WorldWideScience

Sample records for bismuth germanates

  1. Thermal degradation of ultrabroad bismuth NIR luminescence in bismuth-doped tantalum germanate laser glasses.

    Science.gov (United States)

    Wang, Liping; Zhao, Yanqi; Xu, Shanhui; Peng, Mingying

    2016-04-01

    Because of ultra-broadband luminescence in 1000-1700 nm and consequent applications in fiber amplifier and lasers in the new spectral range where traditional rare earth cannot work, bismuth-doped laser glasses have received rising interest recently. For long-term practical application, thermal degradation must be considered for the glasses. This, however, has seldom been investigated. Here we report the thermal degradation of bismuth-doped germanate glass. Heating and cooling cycle experiments at high temperature reveal strong dependence of the thermal degradation on glass compositions. Bismuth and tantalum lead to the reversible degradation, while lithium can produce permanent irreversible degradation. The degradation becomes worse as lithium content increases in the glass. Absorption spectra show this is due to partial oxidation of bismuth near-infrared emission center. Surprisingly, we notice the emission of bismuth exhibits blueshift, rather than redshift at a higher temperature, and the blueshift can be suppressed by increasing the lithium content. PMID:27192231

  2. Thermal stimulation of exoelectronic emission in bismuth germanate single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Kalent' ev, V.A.; Kargin, V.F.; Kargin, Yu.F.; Kortov, V.S.; Skorikov, V.M.; Shul' gin, B.V.

    1987-08-01

    A systematic study of the properties of Bi/sub 4/Ge/sub 3/O/sub 12/ (BGO) indicates that these crystals, along with photoemission (luminescence and scintillation) show exoelectronic emission following thermal excitation from x-ray irradiation. Samples of BGO studied in this paper were grown by the Czochralski method. It is found that the relationship between exoemission in BGO and ordinary GeO/sub 2/ indicates the dominant role played by perturbation of the germanium oxide sublattice in the emission process in bismuth germanate.

  3. Production of bismuth germanate ceramic scintillators by combustion synthesis route

    International Nuclear Information System (INIS)

    The present work presents the results from production of ceramic scintillator Bi4Ge3O12 (bismuth germanate – BGO), which is very sensitive to beta, gamma and X-rays. The production route adopted was combustion synthesis. In this route, the precursors germanium oxide and bismuth nitrate were mixed to urea, used as fuel, and heated up to the ignition temperature, 500 °C. The ignition starts an exothermic reaction that promotes the formation of the desired crystalline phase. It was observed a dependency of the agglomeration of the synthesized powders upon the pH of the initial mixture. The pH was controlled through the addition of ammonium dioxide, and was varied from zero up to 9. Intermediate crystalline phases were observed by DRX measurements of the product of the combustion reaction. After calcination at 600 °C/24 h, the Bi12GeO20 content was enhanced. The optimum conditions of synthesis and sintering of the samples were determined through auxiliary techniques such as DTA and SEM. The synthesized powders presented particle size near 10 nm, whereas the sintered grains reached near 2 μm. The relative density of sintered ceramics, obtained from Archimedes’ method, was 96%. (author)

  4. Energy levels scheme simulation of divalent cobalt doped bismuth germanate

    International Nuclear Information System (INIS)

    The aim of this paper is to simulate the energy levels scheme for Bismuth Germanate (BGO) doped with divalent cobalt, in order to give a reliable explanation for spectral experimental data. In the semiempirical crystal field theory we first modeled the Crystal Field Parameters (CFPs) of BGO:Cr2+ system, in the frame of Exchange Charge Model (ECM), with actually site symmetry of the impurity ions after doping. The values of CFPs depend on the geometry of doped host matrix and by parameter G of ECM. First, we optimized the geometry of undoped BGO host matrix and afterwards, that of doped BGO with divalent cobalt. The charges effect of ligands and covalence bonding between cobalt cations and oxygen anions, in the cluster approach, also were taken into account. With the obtained values of the CFPs we simulate the energy levels scheme of cobalt ions, by diagonalizing the matrix of the doped crystal Hamiltonian. Obviously, energy levels and estimated Racah parameters B and C were compared with the experimental spectroscopic data and discussed. Comparison of obtained results with experimental data shows quite satisfactory, which justify the model and simulation schemes used for the title system

  5. Energy levels scheme simulation of divalent cobalt doped bismuth germanate

    Energy Technology Data Exchange (ETDEWEB)

    Andreici, Emiliana-Laura, E-mail: andreicilaura@yahoo.com [Department of Physics, West University of Timisoara, Bd. V. Parvan 4,300223 Timisoara (Romania); Petkova, Petya [Shumen University “Konstantin Preslavsky”, 115 Universitetska street, 9712 Shumen (Bulgaria); Avram, Nicolae M. [Department of Physics, West University of Timisoara, Bd. V. Parvan 4,300223 Timisoara (Romania); Academy of Romanian Scientists, Independentei 54, 050094-Bucharest (Romania)

    2015-12-07

    The aim of this paper is to simulate the energy levels scheme for Bismuth Germanate (BGO) doped with divalent cobalt, in order to give a reliable explanation for spectral experimental data. In the semiempirical crystal field theory we first modeled the Crystal Field Parameters (CFPs) of BGO:Cr{sup 2+} system, in the frame of Exchange Charge Model (ECM), with actually site symmetry of the impurity ions after doping. The values of CFPs depend on the geometry of doped host matrix and by parameter G of ECM. First, we optimized the geometry of undoped BGO host matrix and afterwards, that of doped BGO with divalent cobalt. The charges effect of ligands and covalence bonding between cobalt cations and oxygen anions, in the cluster approach, also were taken into account. With the obtained values of the CFPs we simulate the energy levels scheme of cobalt ions, by diagonalizing the matrix of the doped crystal Hamiltonian. Obviously, energy levels and estimated Racah parameters B and C were compared with the experimental spectroscopic data and discussed. Comparison of obtained results with experimental data shows quite satisfactory, which justify the model and simulation schemes used for the title system.

  6. Femtosecond Laser-Written Waveguides in a Bismuth Germanate Single Crystal

    International Nuclear Information System (INIS)

    We demonstrate the fabrication of symmetric waveguides in a bismuth germanate (BGO) single crystal using a double line approach by an 800 nm femtosecond laser. The optical attenuation of the single mode waveguide is measured to be 4.2 dB/cm at 633 nm. The influence of pulse energy and focal depth on the end facet of the irradiated region is also studied. This technique is promising to fabricate buried BGO waveguide arrays used in positron emission tomography systems. (general)

  7. New Bismuth Germanate Oxide Nanoparticle Material for Biolabel Applications in Medicine

    OpenAIRE

    M. J. Oviedo; Contreras, O. E.; Y. Rosenstein; Vazquez-Duhalt, R.; Z. S. Macedo; Carbajal-Arizaga, G. G.; G. A. Hirata

    2016-01-01

    Bismuth germanate (Bi4Ge3O12, BGO) has been the focus of several studies due to its scintillation properties. It has been employed as detector in scientific research and medicine, and herein we studied its possible biomedical applications. The photoluminescence properties of the uncoated and protein-coated nanoparticles were analyzed in different body fluids, at different pH. The nanoparticles yielded blueish-white luminescence with a maximum emission peak at 485 nm corresponding to the 3P1→1...

  8. Laser-diode excited intense upconversion luminescence of Er3+ in bismuth-lead-germanate glasses

    Institute of Scientific and Technical Information of China (English)

    Li Tao; Zhang Qin-Yuan; Jiang Zhong-Hong

    2007-01-01

    We have investigated infrared-to-visible upconversion luminescence of Er3 in bismuth-lead-germanate glasses.The UV cutoff wavelength is shortened while its lifetime is increased almost linearly, with PbF2 substituting for PbO in the bismuth-lead-germanate glasses. Three emissions centred at around 529, 545 and 657 nm are clearly observed, which are identified as originating from the 2H11/2 →4 I15/2,4 Ss/2 →4 I15/2 and 4F9/2 →4 I15/2 transitions, respectively. It is noted that all the upconversion emission intensities increase with PbF2 concentration increasing. The ratio between the intensities of red and green emissions increases with the increasing of PbF2 content. Energy transfer processes and nonradiative phonon-assisted decays account for the populations of the 2H11/2,4 S3/2 and 4F9/2 levels. The quadratic dependence of fluorescence on excitation laser power confirms a two-photon process to contribute to the upconversion emissions.

  9. Performance of bismuth germanate active shielding on a balloon flight over Antarctica

    Science.gov (United States)

    Rester, A. C.; Coldwell, R. L.; Trombka, J. I.; Starr, R.; Eichhorn, G.

    1990-01-01

    The GRAD (Gamma-Ray Advanced Detector) gamma-ray spectrometer was flown on a balloon at an altitude of 36.6 km over Antarctica on January 8-10, 1988, where it was used to make observations of SN 1987A. The performance of the bismuth germanate (BGO) active shielding in the near-space environment over Antarctica is examined. The promised effectiveness of this shielding in the suppression of unwanted background has been demonstrated. The BGO-shielded GRAD spectrometer detected gamma-ray lines with fluxes of 0.002/sq cm sec from SN 1987A in a radiation background approximately a factor of 4 more intense than that over Alice Springs, Australia. This level of sensitivity indicates that BGO is at least as effective as CsI when used as active shielding. Isomerism is common, both in the bismuth and germanium regions of the nuclear chart, but is found to be less of a problem for background suppression in the latter region than in the former.

  10. Spectroscopic properties of bismuth-germanate glasses co-doped with erbium and holmium ions

    Science.gov (United States)

    Ragin, Tomasz; Kochanowicz, Marcin; Żmojda, Jacek; Dorosz, Dominik

    2014-05-01

    In the article an analysis of thermal and spectroscopic properties of heavy metal oxide glasses from the Bi2O3-Ga2O3- Na2O-Ge2O3 system doped with rare earth elements were presented. It has been focused on the elaboration of the glass composition in terms of low phonon energy, high transparency in the range of infrared region and high thermal stability (ΔT=160 °C) required in optical fiber technology. Fabricated glasses co-doped with Er3+/Ho3+ions under 980 nm laser diode excitation exhibit emission at 1.55 μm (Er3+: 4I 13/2 → 4I15/2) and 2.0 μm (Ho3+: 4I7 → 5I8). The emission at 2.0 μm results from the Er3+ → Ho3+energy transfer. Taking into account great thermal stability and good optical properties such as high transparency (up to 80%) or high refractive index (2.23), the fabricated bismuth-germanate glass co-doped with Er3+/Ho3+ is promising material for construction of active optical fibers operating in the range of mid-infrared.

  11. A bismuth germanate-avalanche photodiode module designed for use in high resolution positron emission tomography

    International Nuclear Information System (INIS)

    A light-tight, hermetically sealed module for use in high resolution positron emission tomography systems is described. The module has external dimensions 3.8 x 13.2 x 33 mm and contains two 3 x 5 x 20 Bismuth Germanate (BGO) scintillators, each with its own 3 x 3 mm silicon avalanche photodiode. When stacked, the vertical packing fraction is 80%. As measured with a 137Cs (662 keV) source, the typical energy resolution is 20% at 220C, reducing to 16% at 00C. The single detector time resolution for the 22Na gamma at 511 keV is typically less 20 ns at 220C, reducing to less than 15 ns at 00C. Further cooling does not improve the performance since the emission time of light from BGO increases at lower temperature. Preliminary results with Gadolinium Orthosilicate show similar energy resolution, better timing resolution (under 10 ns), but as is known, a slightly poorer photofraction and stopping power

  12. Neutron detection and multiplicity counting using a boron-loaded plastic scintillator/bismuth germanate phoswich detector array

    International Nuclear Information System (INIS)

    Neutron detection and multiplicity counting has been investigated using a boron-loaded plastic scintillator/bismuth germanate phoswich detector array. Boron-loaded plastic combines neutron moderation (H) and detection (10B) at the molecular level, thereby physically coupling increasing detection efficiency and decreasing die-away time with detector volume. Both of these characteristics address a fundamental limitation of thermal-neutron multiplicity counters, where 3He proportional counters are embedded in a polyethylene matrix. Separation of the phoswich response into its plastic scintillator and bismuth germanate components was accomplished on a pulse-by-pulse basis using custom integrator and timing circuits. In addition, a custom time-tag module was used to provide a time for each detector event. Analysis of the combined energy and time event stream was performed by calibrating each detector's response and filtering based on the presence of a simultaneous energy deposition corresponding to the 10B(n,alpha) reaction products in the plastic scintillator (93 keVee) and the accompanying neutron-capture gamma ray in the bismuth germanate (478 keV). Time-correlation analysis was subsequently performed on the filtered event stream to obtain shift-register-type singles and doubles count rates. Proof-of-principle measurements were conducted with a variety of gamma-ray and neutron sources including 137Cs, 54Mn, AmLi, and 252Cf. Results of this study indicate that a neutron-capture probability of ∼10% and a die-away time of ∼10 micros are possible with a 4-detector array with a detector volume of 1600 cm3. Simulations were performed that indicate neutron-capture probabilities on the order of 50% and die-away times of less than 4 micros are realistically achievable. While further study will be required for practical application of such a detection system, the results obtained in this investigation are encouraging and may lead to a new class of high-efficiency, short

  13. Performance of bismuth germanate active shielding on a balloon flight over Antarctica

    Energy Technology Data Exchange (ETDEWEB)

    Rester, A.C.; Coldwell, R.L. (Institute for Astrophysics and Planetary Exploration, Univ. of Florida, Alachua, FL (US)); Trombka, J.I. (National Aeronautics and Space Administration, Greenbelt, MD (USA). Goddard Space Flight Center); Starr, R. (Catholic Univ. of America, Washington, DC (USA). Dept. of Physics); Eichhorn, G. (Steward Observatory, Tucson, AZ (USA)); Lasche, G.P. (Defense Advanced Research Projects Agency, Arlington, VA (USA))(Defense Advanced Research Projects Agency, Arlington, VA (USA))

    1990-04-01

    The GRAD gamma-ray spectrometer was flown on a high-altitude balloon at an altitude of 36.6 km over Antarctica on January 8-10, 1988 where it was used to make observations of Supernova 1987a. The performance of the bismuth germinate active shielding in the near-space environment over Antarctica is examined.

  14. Performance of bismuth germanate active shielding on a balloon flight over Antarctica

    International Nuclear Information System (INIS)

    The GRAD gamma-ray spectrometer was flown on a high-altitude balloon at an altitude of 36.6 km over Antarctica on January 8-10, 1988 where it was used to make observations of Supernova 1987a. The performance of the bismuth germinate active shielding in the near-space environment over Antarctica is examined

  15. Fabrication and testing of diamond-machined gratings in ZnSe, GaP, and bismuth germanate for the near-infrared and visible

    Science.gov (United States)

    Kuzmenko, Paul J.; Little, Steve L.; Ikeda, Yuji; Kobayashi, Naoto

    2008-07-01

    High quality immersion gratings for infrared applications have been demonstrated in silicon and germanium. To extend this technology to shorter wavelengths other materials must be investigated. We selected three materials, zinc selenide, gallium phosphide and bismuth germanate (Bi4Ge3O12), based on high refractive index, good visible transmission and commercial availability in useful sizes. Crystal samples were diamond turned on an ultra-precision lathe to identify preferred cutting directions. Using this information we diamond-flycut test gratings over a range of feed rates to determine the optimal cutting conditions. For both ZnSe and GaP good surface quality was achieved at feed rates up to 1.0 cm/minute using a special compound angle diamond tool with negative rake angles on both cutting surfaces. The surface roughness of the groove facets was about 4 nm. A Zygo interferometer measured grating wavefront errors in reflection. For the ZnSe the RMS error was 80%), low random groove error (2.0 nm rms), and Rowland ghost intensities at < 0.1%. Preliminary tests on bismuth germanate show high tool wear.

  16. Fabrication and testing of diamond-machined gratings in ZnSe, GaP, and bismuth germanate for the near infrared and visible

    Energy Technology Data Exchange (ETDEWEB)

    Kuzmenko, P J; Little, S L; Ikeda, Y; Kobayashi, N

    2008-06-22

    High quality immersion gratings for infrared applications have been demonstrated in silicon and germanium. To extend this technology to shorter wavelengths other materials must be investigated. We selected three materials, zinc selenide, gallium phosphide and bismuth germanate (Bi{sub 4}Ge{sub 3}O{sub 12}), based on high refractive index, good visible transmission and commercial availability in useful sizes. Crystal samples were diamond turned on an ultra-precision lathe to identify preferred cutting directions. Using this information we diamond-flycut test gratings over a range of feed rates to determine the optimal cutting conditions. For both ZnSe and GaP good surface quality was achieved at feed rates up to 1.0 cm/minute using a special compound angle diamond tool with negative rake angles on both cutting surfaces. The surface roughness of the groove facets was about 4 nm. A Zygo interferometer measured grating wavefront errors in reflection. For the ZnSe the RMS error was < {lambda}/20 at 633nm. More extensive testing was performed with a HeNe laser source and a cooled CCD camera. These measurements demonstrated high relative diffraction efficiency (> 80%), low random groove error (2.0 nm rms), and Rowland ghost intensities at < 0.1%. Preliminary tests on bismuth germanate show high tool wear.

  17. Surface plasmon resonance-enhanced 2 μm emission of bismuth germanate glasses doped with Ho3+/Tm3+ ions

    Science.gov (United States)

    Tang, Junzhou; Lu, Kelun; Zhang, Shaoqian; Zhang, Peiqing; Chen, Feifei; Dai, Shixun; Xu, Yinsheng

    2016-04-01

    In this paper, we report 2 μm emission in bismuth germanate glasses doped with Ho3+/Tm3+ ions enhanced by surface plasmon resonance of Ag nanoparticles (NPs) under 800 nm laser excitation. We perform broadband mid-infrared emissions from 1700 nm to 2200 nm corresponding to Tm3+: 3F4 → 3H6 and Ho3+: 5I7 → 5I8 transitions. The energy transfer from Tm3+ to Ho3+ ions results in a strong 2030 nm emission. Results demonstrate that the emission intensity of the sample containing Ag NPs is much higher than that of the sample without Ag addition. For the best AgTH6 sample, the absorption and emission cross sections of Ho3+ transition (5I8 → 5I7) reach 0.5 × 10-20 cm2 at 1945 nm and 0.78 × 10-20 cm2 at 2030 nm, respectively. The comparative performances, i.e., σe × full width at half maximum and σe × τ, are approximately 129 × 10-20 cm2 nm and 24.8 × 10-24 cm2 s, respectively. Therefore, the glass has a potential application as 2.0 μm laser active media.

  18. Single- and double energy N+ ion irradiated planar optical waveguides in Er: Tungsten–tellurite oxide glass and sillenite type Bismuth Germanate crystals working up to telecommunications wavelengths

    International Nuclear Information System (INIS)

    Ion implantation proved to be a universal technique for producing waveguides in most optical materials. Tellurite glasses are good hosts of rare-earth elements for the development of fibre and integrated optical amplifiers and lasers covering all the main telecommunication bands. Er3+-doped tellurite glasses are good candidates for the fabrication of broadband amplifiers in wavelength division multiplexing around 1.55 μm, as they exhibit large stimulated cross sections and broad emission bandwidth. Fabrication of channel waveguides in such a material via N+ ion implantation was reported recently. Sillenite type Bismuth Germanate (BGO) crystals are good nonlinear optical materials. Parameters of waveguide fabrication in both materials via implantation of MeV-energy N+ ions were optimized. First single-energy implantations at 3.5 MeV at various fluences were applied. Waveguide operation up to 1.5 μm was observed in both materials. Then double-energy implantations at a fixed upper energy of 3.5 MeV and lower energies between 2.5 and 3.1 MeV were performed to suppress leaky modes by increasing barrier width. Improvement of waveguide characteristics was found by m-line spectroscopy and spectroscopic ellipsometry

  19. Ultrasonic and optical properties and emission of Er3+/Yb3+ doped lead bismuth-germanate glass affected by Bi+/Bi2+ ions

    International Nuclear Information System (INIS)

    Rare earth doped heavy metal oxide glasses instead of silicates are interesting research area, especially, for their potential application in optoelectronics. In addition, contribution of different bismuth ionization states in photoluminescence spectra is still an open question. In this research work, [GeO2]60–[PbO]40−x–[½Bi2O3]x, glass hosts where x=0, 10, 20, 30, and 40 mol% and 0.5 wt% of Er2O3 and 1.5 wt% of Yb2O3 as doping agents were studied. The activated heavy metal oxide glass samples were synthesized by conventional melt quenching method. The optical properties were studied by refractive index, UV–visible absorption and photoluminescence (PL) measurements, and explained in terms of the Judd–Ofelt theory. The glass was also studied by ultrasonic measurements and showed that the velocity of sound is lower in Pb-rich samples. Our results also, showed that emission intensities are higher in host glasses with lower sound velocities, which is attributed mainly to multiphonon relaxation. In addition, variation of PL intensities with increase of bismuth composition was related not only to the variation of Debye temperature and refractive index; but also, to the increase of Ω6 in Pb-rich samples due to the ligand field and existence of Bi2+/Bi+ ions in Bi-rich glasses. -- Highlights: • The ultrasonic measurements on glass showed that the velocity of sound is higher in Pb-rich samples. • The PL intensity is higher in glasses with lower Debye temperature and higher refractive index. • The PL intensity is related to the multiphonon relaxation, ligand field (Ω6) and Bi2+/Bi+ ions

  20. Bismuth, Metronidazole, and Tetracycline

    Science.gov (United States)

    Helidac® (as a kit containing Bismuth Subsalicylate, Metronidazole, Tetracycline) ... Bismuth, metronidazole, and tetracycline is used along with other ulcer medications to treat duodenal ulcers. It is in a class of medications called ...

  1. Novel Bismuth Nanotubes

    Institute of Scientific and Technical Information of China (English)

    苏长荣; 李家明

    2002-01-01

    Theoretical investigations show that bismuth nanotubes are semiconductors for all diameters. For smalldiameter bismuth nanotubes, the band structures and bandgaps vary strongly with the strong hybridization effect. When the diameters are larger than 18 A, the bandgaps ofBi (n, n) and (n, 0) nanotubes approach 0.63 e V, corresponding to the bandgap of bismuth sheet at the Γ point. Thus, bismuth nanotubes are expected to be a potential semiconductor nanomaterial in future nanoelectronics.

  2. The bismuth burden - a challenge for the accident insurance (Berufsgenossenschaften)

    International Nuclear Information System (INIS)

    The Soviet-German Bismuth AG was a state within a state in the former GDR. Uranium mining not only caused great ecological burdens but also gave rise to many problems for the accident insurance. Occupational diseases are of course, very important in the context of malignous growth caused by ionised radiation. The accident insurances (Berufsgenossenschaften) recognised the size of this unique problem and have initiated measures towards its solution. (orig.)

  3. Valley polarization in bismuth

    Science.gov (United States)

    Fauque, Benoit

    2013-03-01

    The electronic structure of certain crystal lattices can contain multiple degenerate valleys for their charge carriers to occupy. The principal challenge in the development of valleytronics is to lift the valley degeneracy of charge carriers in a controlled way. In bulk semi-metallic bismuth, the Fermi surface includes three cigar-shaped electron valleys lying almost perpendicular to the high symmetry axis known as the trigonal axis. The in-plane mass anisotropy of each valley exceeds 200 as a consequence of Dirac dispersion, which drastically reduces the effective mass along two out of the three orientations. According to our recent study of angle-dependent magnetoresistance in bismuth, a flow of Dirac electrons along the trigonal axis is extremely sensitive to the orientation of in-plane magnetic field. Thus, a rotatable magnetic field can be used as a valley valve to tune the contribution of each valley to the total conductivity. As a consequence of a unique combination of high mobility and extreme mass anisotropy in bismuth, the effect is visible even at room temperature in a magnetic field of 1 T. Thus, a modest magnetic field can be used as a valley valve in bismuth. The results of our recent investigation of angle-dependent magnetoresistance in other semi-metals and doped semiconductors suggest that a rotating magnetic field can behave as a valley valve in a multi-valley system with sizeable mass anisotropy.

  4. Optical properties of bismuth-doped SiO2- or GeO2-based glass core optical fibers

    OpenAIRE

    Firstova, Elena G.

    2015-01-01

    A detailed study of optical properties of bismuth-doped fibers based on SiO2 and GeO2 glasses containing no other dopants has been carried out. To provide important information about spectroscopic properties of IR bismuth-related active centers (BAC) the excitation-emission fluorescence spectra for a spectral region of 220-2000 nm have been measured. The obtained three-dimensional spectra have been presented for different host glass compositions: silicate, germanate, aluminosilicate and phosp...

  5. Energetics of bismuth vanadate

    Energy Technology Data Exchange (ETDEWEB)

    Nagabhushana, G.P.; Tavakoli, A.H.; Navrotsky, A., E-mail: anavrotsky@ucdavis.edu

    2015-05-15

    Bismuth vanadate has gained considerable interest as a photoanode for water splitting reactions under visible light. It exists in four different polymorphs, out of which three of them have been synthesized. Thermodynamic properties of these three polymorphs are investigated using high temperature oxide melt solution calorimetry. The monoclinic scheelite phase which exhibits photocatalytic activity under visible light is found to be the most stable polymorph, followed by tetragonal scheelite which exhibits activity under UV light. The photocatalytically inactive tetragonal zircon form is found to be the least stable polymorph. The small difference in enthalpy of formation between the two scheelite structures (−8 kJ/mol) is in accord with the reversibility of the transformation between them and the larger difference between the most stable monoclinic phase and the least stable tetragonal zircon phase (−23 kJ/mol) is in accord with the irreversible (monoclinic→tetragonal zircon) phase transformation. - Graphical abstract: Schematic representation of polymorphic transitions in BiVO{sub 4} along with their formation enthalpies. - Highlights: • Bismuth vanadate crystallizes in three different polymorphs. • High temperature calorimetric measurements were made to determine their formation enthalpies. • Enthalpy of formation decreases in the order BV-ms→BV-ts→BV-tz. • Photocatalytically active monoclinic-BiVO{sub 4} was found to be the most stable polymorph.

  6. An Unusual Bismuth Ethanedisulfonate Network

    Directory of Open Access Journals (Sweden)

    Fabienne Gschwind

    2012-09-01

    Full Text Available The three dimensional bismuth ethanedisulfonate framework Bi(O3SC2H4SO31.5(H2O2 was synthesized under hydrothermal conditions using the bidentate ligand 1,2-ethanedisulfonate and then characterized through X-ray diffraction and elemental analyses. The bismuth cation coordinates at three different ethanedisulfonate ligands and has a coordination number of eight, which is accompanied by a distorted square antiprismatic configuration. Here, we report on the crystal structure of this bismuth metal–organic framework and its coordination behavior, which has thus far not been reported in heavier main group elements.

  7. German technology

    Energy Technology Data Exchange (ETDEWEB)

    Woof, M.

    2002-09-01

    A selection of short articles reports on: German underground coal and potash developments in equipment for surface coal mining and for crushing and conveying and designs and applications of hydraulic shovels. 11 photos.

  8. Unusual anti-thermal degradation of bismuth NIR luminescence in bismuth doped lithium tantalum silicate laser glasses.

    Science.gov (United States)

    Tan, Linling; Wang, Liping; Peng, Mingying; Xu, Shanhui; Zhang, Qinyuan

    2016-08-01

    For application of bismuth laser glasses in either fiber amplifier or laser, their performance stability in long run should be understood especially in extreme conditions. However, so far, there are few reports on it. Here, we found, after the cycle experiments on heating and cooling, that the proper increase of lithium content in lithium tantalum silicate laser glass can lead to unusual anti-thermal degradation of bismuth NIR luminescence, which completely differs from the scenario in germanate glass. FTIR, 29Si MAS NMR spectra, absorption and dynamic photoluminescence spectra are employed to unravel how this happens. The results illustrate that it should be due to the decrease of polymerization of silicate glass network, which in turn allows the regeneration at 250°C, and therefore, the content increase of bismuth NIR emission centers. In the meanwhile, we noticed though Bi luminescence can be thermally quenched its peak does not shift along with temperature, which seldom appears in laser materials. The unique property might guarantee the unshift of Bi fiber laser wavelength once such glass was made into fiber devices even as the environmental temperature changes. The role of lithium is discussed in the evolution of glass structures, the suppression of glass heterogeneity, and the thermal stability of Bi luminescence, and it should be helpful to design homogeneous silicate laser glass with outstanding thermal stability. PMID:27505827

  9. Superconducting transition temperature of metastable, crystalline lead-bismuth alloys

    International Nuclear Information System (INIS)

    The increase of the superconducting temperature by ion implantation with bismuth-ions in a saturated lead-bismuth alloy, by recoil-implantation and by quenching of a lead-bismuth alloy with bismuth precipitates was studied. At room-temperature an increase of 11 at% Bi over the thermodynamic solution limit in a lead-bismuth alloy could be measured. The highest superconducting temperature was 9.02 K for a lead-bismuth alloy with 43 at% bismuth. (orig.)

  10. Bismuth bronze from machu picchu, peru.

    Science.gov (United States)

    Gordon, R B; Rutledge, J W

    1984-02-10

    The decorative bronze handle of a tumi excavated at the Inca city of Machu Picchu, Peru, contains 18 percent bismuth and appears to be the first known example of the use of bismuth with tin to make bronze. The alloy is not embrittled by the bismuth because the bismuth-rich constituent does not penetrate the grain boundaries of the matrix phase. The use of bismuth facilitates the duplex casting process by which the tumi was made and forms an alloy of unusual color. PMID:17749940

  11. German Studies in America. German Studies Notes.

    Science.gov (United States)

    Sander, Volkmar; Osterle, Heinz D.

    This volume contains two papers, "German Studies in America," by Volkmar Sander, and "Historicism, Marxism, Structuralism: Ideas for German Culture Courses," by Heinz D. Osterle. The first paper discusses the position of German studies in the United States today. The greatest challenge comes from low enrollments; therefore, German departments must…

  12. Comparative Study of Semiconductors Bismuth Iodate, Bismuth Triiodide and Bismuth Trisulphide Crystals

    Directory of Open Access Journals (Sweden)

    T.K. Patil

    2012-12-01

    Full Text Available In the present investigation, crystals of Bismuth Iodate[Bi(IO33], Bismuth Iodide[BiI3] and Bismuth- Tri Sulphide [Bi2S3] were grown by a simple gel technique using single diffusion method. The optimum growth conditions were established by varying various parameters such as pH of gel solution, gel concentration, gel setting time, concentration of reactant etc. Gel was prepared by mixing sodium meta silicate (Na2SiO35H2O, glacial acetic acid (CH3COOH and supernant bismuth chloride (BiCl3 at pH value 4.4 and transferred in glass tube of diameter 2.5 cm and 25 cm in length. The mouth of test tube was covered by cotton plug and kept it for the setting. After setting the gel, it was left for aging. After 13 days duration the second supernant K(IO3, KI3 and H2S water gas solution was poured over the set gel by using pipette then it was kept undisturbed. After 72 hours of pouring the second supernatant, the small nucleation growth was observed at below the interface of gel. The good quality crystals of [Bi(IO33], [BiI3] and [Bi2S3] were grown. These grown crystals were characterized by XRD, FTIR, Chemical Analysis and Electrical Conductivity.

  13. Bismuth absorption from 205 Bi-labelled pharmaceutical bismuth compounds used in the treatment of peptic ulcer disease

    International Nuclear Information System (INIS)

    The absorption of bismuth from five 205Bi-labelled pharmaceutically used bismuth compounds was studied in man. From single oral doses of all compounds under investigation only <0.1% bismuth was absorbed and excreted with the urine. A significantly higher absorption was observed from the colloidal bismuth subcitrate and the basic bismuth gallate than from the basic bismuth salicylate, nitrate and aluminate. No retention of bismuth in the whole body was found from the single dose experiment. The biologic fast-term half-lives of absorbed bismuth were calculated to be 0.12 and 1.5 days. 14 refs., 2 figs., 1 tab

  14. Bismuth absorption from sup 205 Bi-labelled pharmaceutical bismuth compounds used in the treatment of peptic ulcer disease

    Energy Technology Data Exchange (ETDEWEB)

    Dresow, B.; Fischer, R.; Gabbe, E.E.; Wendel, J.; Heinrich, H.C. (Eppendorf University Hospital, Hamburg (Germany))

    1992-04-01

    The absorption of bismuth from five {sup 205}Bi-labelled pharmaceutically used bismuth compounds was studied in man. From single oral doses of all compounds under investigation only <0.1% bismuth was absorbed and excreted with the urine. A significantly higher absorption was observed from the colloidal bismuth subcitrate and the basic bismuth gallate than from the basic bismuth salicylate, nitrate and aluminate. No retention of bismuth in the whole body was found from the single dose experiment. The biologic fast-term half-lives of absorbed bismuth were calculated to be 0.12 and 1.5 days. 14 refs., 2 figs., 1 tab.

  15. Bismuth ions are metabolized into autometallographic traceable bismuth-sulphur quantum dots

    Directory of Open Access Journals (Sweden)

    M Stoltenberg

    2009-06-01

    Full Text Available Bismuth – sulphur quantum dots can be silver enhanced by autometallography (AMG. In the present study, autometallographic silver enhanced bismuth-sulphur nanocrystals were isolated from unfixed cryo-sections of kidneys and livers of rats exposed to bismuth (Bi207 subnitrate. After being subjected to AMG all the organic material was removed by sonication and enzymatic digestion and the silver enhanced Bi- S quantum dots spun down by an ultracentrifuge and analyzed by scintillation. The analysis showed that the autometallographic technique traces approximately 94% of the total bismuth. This implies that the injected bismuth is ultimately captured in bismuthsulphur quantum dots, i.e., that Bi-S nanocrystals are the end product of bismuth metabolism

  16. Extraction and separation of bismuth(III).

    Science.gov (United States)

    Langade, A D; Shinde, V M

    1981-10-01

    Separation of bismuth from beryllium, lead, iron(III), indium, scandium, lanthanum, antimony(III), zirconium, titanium, thorium, vanadium(V), molybdenum(VI), uranium (VI) and chromium(VI) is achieved by selective extraction of bismuth from 0.1M sodium salicylate solution (adjusted to pH 7) into mesityl oxide (MeO). The extracted species is Bi (HOC(6)H(4)COO)(3).3MeO. The results are accurate within +/- 0.5%, with a standard deviation of 0.8%. The separation and determination of bismuth takes only 15 min. PMID:18963000

  17. Gravimetric Analysis of Bismuth in Bismuth Subsalicylate Tablets: A Versatile Quantitative Experiment for Undergraduate Laboratories

    Science.gov (United States)

    Davis, Eric; Cheung, Ken; Pauls, Steve; Dick, Jonathan; Roth, Elijah; Zalewski, Nicole; Veldhuizen, Christopher; Coeler, Joel

    2015-01-01

    In this laboratory experiment, lower- and upper-division students dissolved bismuth subsalicylate tablets in acid and precipitated the resultant Bi[superscript 3+] in solution with sodium phosphate for a gravimetric determination of bismuth subsalicylate in the tablets. With a labeled concentration of 262 mg/tablet, the combined data from three…

  18. Hydrothermal synthesis map of bismuth titanates

    International Nuclear Information System (INIS)

    The hydrothermal synthesis of four bismuth titanate materials from common bismuth and titanium precursors under hydrothermal conditions is described. Reaction of NaBiO3·2H2O and anatase TiO2 in concentrated NaOH solution at 240 °C is shown to produce perovskite and sillenite phases Na0.5Bi0.5TiO3 and Bi12TiO20, depending on the ratio of metal precursors used. When KOH solution is used and a 1:1 ratio of the same precursors, a pyrochlore Bi1.43Ti2O6(OH)0.29(H2O)0.66 is formed. The use of a mixture of HNO3 and NaOH is shown to facilitate the formation of the Aurivillius-type bismuth titanate Bi4Ti3O12. The phases have been isolated separately as phase-pure powders and profile refinement of powder X-ray diffraction data allows comparisons with comparable materials reported in the literature. Analysis of Bi LIII-edge X-ray absorption near edge structure (XANES) spectra of the materials shows the oxidation state of bismuth is +3 in all of the hydrothermally derived products. - Graphical abstract: Use of NaBiO3·2H2O and TiO2 as reagents under hydrothermal conditions allows the phase-pure preparation of four crystalline bismuth titanate materials. Highlights: ► NaBiO3 and TiO2 under hydrothermal conditions allow formation of bismuth titanates. ► Synthesis of four distint phases has been mapped. ► Bi LIII-edge XANES shows Bi is reduced to oxidation state +3 in all materials. ► A new hydrated bismuth titanate pyrochlore has been isolated

  19. Metabolism of Bismuth Subsalicylate and Intracellular Accumulation of Bismuth by Fusarium sp. Strain BI

    OpenAIRE

    Dodge, Anthony G.; Wackett, Lawrence P

    2005-01-01

    Enrichment cultures were conducted using bismuth subsalicylate as the sole source of carbon and activated sludge as the inoculum. A pure culture was obtained and identified as a Fusarium sp. based on spore morphology and partial sequences of 18S rRNA, translation elongation factor 1-α, and β-tubulin genes. The isolate, named Fusarium sp. strain BI, grew to equivalent densities when using salicylate or bismuth subsalicylate as carbon sources. Bismuth nitrate at concentrations of up to 200 μM d...

  20. Electrodeposition and Characterization of Bismuth Telluride Nanowires

    Science.gov (United States)

    Frantz, C.; Stein, N.; Gravier, L.; Granville, S.; Boulanger, C.

    2010-09-01

    In this work, we report thermoelectric measurements on electroplated bismuth telluride nanowires. Porous polycarbonate membranes, obtained by ion-track irradiation lithography, were chosen as electroplating templates. Bismuth telluride nanowires were achieved in acidic media under potentiostatic conditions at -100 mV versus saturated silver chloride electrode. The filling ratio of the pores was increased to 80% by adding dimethyl sulfoxide to the electrolyte. Whatever the experimental conditions, the nanowires were polycrystalline in the rhombohedral phase of Bi2Te3. Finally, the power output of arrays of bismuth telluride nanowires was analyzed as a function of load resistance. The results were strongly dependent on the internal resistance, which can be significantly reduced by the presence of dimethyl sulfoxide during electroplating.

  1. Liquid Bismuth Feed System for Electric Propulsion

    Science.gov (United States)

    Markusic, T. E.; Polzin, K. A.; Stanojev, B. J.

    2006-01-01

    Operation of Hall thrusters with bismuth propellant has been shown to be a promising path toward high-power, high-performance, long-lifetime electric propulsion for spaceflight missions. For example, the VHITAL project aims td accurately, experimentally assess the performance characteristics of 10 kW-class bismuth-fed Hall thrusters - in order to validate earlier results and resuscitate a promising technology that has been relatively dormant for about two decades. A critical element of these tests will be the precise metering of propellant to the thruster, since performance cannot be accurately assessed without an accurate accounting of mass flow rate. Earlier work used a pre/post-test propellant weighing scheme that did not provide any real-time measurement of mass flow rate while the thruster was firing, and makes subsequent performance calculations difficult. The motivation of the present work was to develop a precision liquid bismuth Propellant Management System (PMS) that provides real-time propellant mass flow rate measurement and control, enabling accurate thruster performance measurements. Additionally, our approach emphasizes the development of new liquid metal flow control components and, hence, will establish a basis for the future development of components for application in spaceflight. The design of various critical components in a bismuth PMS are described - reservoir, electromagnetic pump, hotspot flow sensor, and automated control system. Particular emphasis is given to material selection and high-temperature sealing techniques. Open loop calibration test results are reported, which validate the systems capability to deliver bismuth at mass flow rates ranging from 10 to 100 mg/sec with an uncertainty of less than +/- 5%. Results of integrated vaporizer/liquid PMS tests demonstrate all of the necessary elements of a complete bismuth feed system for electric propulsion.

  2. Maury Journals - German Vessels

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — German vessels observations, after the 1853 Brussels Conference that set International Maritime Standards, modeled after Maury Marine Standard Observations.

  3. Burnout current density of bismuth nanowires

    Science.gov (United States)

    Cornelius, T. W.; Picht, O.; Müller, S.; Neumann, R.; Völklein, F.; Karim, S.; Duan, J. L.

    2008-05-01

    Single bismuth nanowires with diameters ranging from 100nmto1μm were electrochemically deposited in ion track-etched single-pore polycarbonate membranes. The maximum current density the wires are able to carry was investigated by ramping up the current until failure occurred. It increases by three to four orders of magnitude for nanowires embedded in the template compared to bulk bismuth and rises with diminishing diameter. Simulations show that the wires are heated up electrically to the melting temperature. Since the surface-to-volume ratio rises with diminishing diameter, thinner wires dissipate the heat more efficiently to the surrounding polymer matrix and, thus, can tolerate larger current densities.

  4. Holographic data storage in photorefractive bismuth tellurite

    International Nuclear Information System (INIS)

    Bismuth tellurite is a photorefractive material for holographic data storage offering unique fixing capabilities. Important material and electro-optic properties obtained by four-wave-mixing and data storage experiments are reviewed and recent results concerning the applicability of bismuth tellurite for holographic data storage, including dynamic range, multiplexing capabilities and bit-error evaluations, are presented. Furthermore, it is demonstrated how the latest progress in growing Bi2TeO5 made this crystal a candidate for durable holographic recording media.

  5. Electron microscopy of barium bismuth titanate multilayer ceramics

    International Nuclear Information System (INIS)

    For a number of years bismuth containing compounds have been used with pre-calcined barium titanate to reduce the sintering temperature of the capacitor formulations. As reported earlier the backscattered electron (BSE) SEM micrographs of the bismuth containing barium titanate ceramic reveal that the grains having an average size of 1.2μm consist of a two phase structure consisting of relatively pure barium titanate grain cores surrounded by bismuth rich grain shells. The TEM and STEM studies along with the EDS analyses show that the bismuth concentration increases sharply as one steps towards the grain boundary with a maximum bismuth content at the grain boundary. It is the purpose of this work to investigate the distribution of bismuth in these formulations including the bismuth content, if any, at the ceramic metal interface as affected by the sintering temperature. The subsequent effect on the electrical resistivity of these ceramics in the multilayer configuration is reported

  6. Metabolism of bismuth subsalicylate and intracellular accumulation of bismuth by Fusarium sp. strain BI.

    Science.gov (United States)

    Dodge, Anthony G; Wackett, Lawrence P

    2005-02-01

    Enrichment cultures were conducted using bismuth subsalicylate as the sole source of carbon and activated sludge as the inoculum. A pure culture was obtained and identified as a Fusarium sp. based on spore morphology and partial sequences of 18S rRNA, translation elongation factor 1-alpha, and beta-tubulin genes. The isolate, named Fusarium sp. strain BI, grew to equivalent densities when using salicylate or bismuth subsalicylate as carbon sources. Bismuth nitrate at concentrations of up to 200 muM did not limit growth of this organism on glucose. The concentration of soluble bismuth in suspensions of bismuth subsalicylate decreased during growth of Fusarium sp. strain BI. Transmission electron microscopy and energy-dispersive spectroscopy revealed that the accumulated bismuth was localized in phosphorus-rich granules distributed in the cytoplasm and vacuoles. Long-chain polyphosphates were extracted from fresh biomass grown on bismuth subsalicylate, and inductively coupled plasma optical emission spectrometry showed that these fractions also contained high concentrations of bismuth. Enzyme activity assays of crude extracts of Fusarium sp. strain BI showed that salicylate hydroxylase and catechol 1,2-dioxygenase were induced during growth on salicylate, indicating that this organism degrades salicylate by conversion of salicylate to catechol, followed by ortho cleavage of the aromatic ring. Catechol 2,3-dioxygenase activity was not detected. Fusarium sp. strain BI grew with several other aromatic acids as carbon sources: benzoate, 3-hydroxybenzoate, 4-hydroxybenzoate, gentisate, d-mandelate, l-phenylalanine, l-tyrosine, phenylacetate, 3-hydroxyphenylacetate, 4-hydroxyphenylacetate, and phenylpropionate. PMID:15691943

  7. Headstart German Program. Cumulative Glossary.

    Science.gov (United States)

    Defense Language Inst., Monterey, CA.

    This glossary lists the vocabulary words used in the ten modules of the German Headstart program. It is a German-English and English-German glossary. The module number in which each word first occurs is given. (AMH)

  8. Probing bismuth ferrite nanoparticles by hard x-ray photoemission: Anomalous occurrence of metallic bismuth

    International Nuclear Information System (INIS)

    We have investigated bismuth ferrite nanoparticles (∼75 nm and ∼155 nm) synthesized by a chemical method, using soft X-ray (1253.6 eV) and hard X-ray (3500, 5500, and 7500 eV) photoelectron spectroscopy. This provided an evidence for the variation of chemical state of bismuth in crystalline, phase pure nanoparticles. X-ray photoelectron spectroscopy analysis using Mg Kα (1253.6 eV) source showed that iron and bismuth were present in both Fe3+ and Bi3+ valence states as expected for bismuth ferrite. However, hard X-ray photoelectron spectroscopy analysis of the bismuth ferrite nanoparticles using variable photon energies unexpectedly showed the presence of Bi0 valence state below the surface region, indicating that bismuth ferrite nanoparticles are chemically inhomogeneous in the radial direction. Consistently, small-angle X-ray scattering reveals a core-shell structure for these radial inhomogeneous nanoparticles.

  9. Photosensitive bismuth ions in lead tungstate

    Czech Academy of Sciences Publication Activity Database

    Vazhenin, V.A.; Potapov, A.P.; Asatryan, G.R.; Nikl, Martin

    2013-01-01

    Roč. 55, č. 4 (2013), s. 803-806. ISSN 1063-7834 Institutional support: RVO:68378271 Keywords : PbWO 4 * single crystal * bismuth * electron paramagnetic resonance Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.782, year: 2013

  10. Hydrothermal synthesis map of bismuth titanates

    Science.gov (United States)

    Sardar, Kripasindhu; Walton, Richard I.

    2012-05-01

    The hydrothermal synthesis of four bismuth titanate materials from common bismuth and titanium precursors under hydrothermal conditions is described. Reaction of NaBiO3·2H2O and anatase TiO2 in concentrated NaOH solution at 240 °C is shown to produce perovskite and sillenite phases Na0.5Bi0.5TiO3 and Bi12TiO20, depending on the ratio of metal precursors used. When KOH solution is used and a 1:1 ratio of the same precursors, a pyrochlore Bi1.43Ti2O6(OH)0.29(H2O)0.66 is formed. The use of a mixture of HNO3 and NaOH is shown to facilitate the formation of the Aurivillius-type bismuth titanate Bi4Ti3O12. The phases have been isolated separately as phase-pure powders and profile refinement of powder X-ray diffraction data allows comparisons with comparable materials reported in the literature. Analysis of Bi LIII-edge X-ray absorption near edge structure (XANES) spectra of the materials shows the oxidation state of bismuth is +3 in all of the hydrothermally derived products.

  11. Bismuth titanate ceramics obtained by hot forging

    International Nuclear Information System (INIS)

    In this work, bismuth titanate samples were obtained from powder calcined at 800 deg C for 24 h through conventional sintering (OF) and hot-forging (HF) methods. The plate-like morphology grains were observed in ceramics obtained in both process. Samples produced by HF showed higher grain orientation, ≅ 90%. (author)

  12. Polyvinyl chloride filled with bismuth oxychloride powder

    Czech Academy of Sciences Publication Activity Database

    Polášková, M.; Sedláček, T.; Kharlamov, Alexander; Pivokonský, Radek; Saha, P.

    Larnaca : Polymer Processing Society, 2009, s. 242. [Polymer Processing Society Europe/Africa Regional Meeting. Larnaca (GR), 18.10.2009-21.10.2009] Institutional research plan: CEZ:AV0Z20600510 Keywords : olyvinyl chloride * bismuth oxychloride * radiopaque agents Subject RIV: BK - Fluid Dynamics

  13. Hydrothermal synthesis map of bismuth titanates

    Energy Technology Data Exchange (ETDEWEB)

    Sardar, Kripasindhu [Department of Chemistry, University of Warwick, Coventry, CV4 7AL (United Kingdom); Walton, Richard I., E-mail: r.i.walton@warwick.ac.uk [Department of Chemistry, University of Warwick, Coventry, CV4 7AL (United Kingdom)

    2012-05-15

    The hydrothermal synthesis of four bismuth titanate materials from common bismuth and titanium precursors under hydrothermal conditions is described. Reaction of NaBiO{sub 3}{center_dot}2H{sub 2}O and anatase TiO{sub 2} in concentrated NaOH solution at 240 Degree-Sign C is shown to produce perovskite and sillenite phases Na{sub 0.5}Bi{sub 0.5}TiO{sub 3} and Bi{sub 12}TiO{sub 20}, depending on the ratio of metal precursors used. When KOH solution is used and a 1:1 ratio of the same precursors, a pyrochlore Bi{sub 1.43}Ti{sub 2}O{sub 6}(OH){sub 0.29}(H{sub 2}O){sub 0.66} is formed. The use of a mixture of HNO{sub 3} and NaOH is shown to facilitate the formation of the Aurivillius-type bismuth titanate Bi{sub 4}Ti{sub 3}O{sub 12}. The phases have been isolated separately as phase-pure powders and profile refinement of powder X-ray diffraction data allows comparisons with comparable materials reported in the literature. Analysis of Bi L{sub III}-edge X-ray absorption near edge structure (XANES) spectra of the materials shows the oxidation state of bismuth is +3 in all of the hydrothermally derived products. - Graphical abstract: Use of NaBiO{sub 3}{center_dot}2H{sub 2}O and TiO{sub 2} as reagents under hydrothermal conditions allows the phase-pure preparation of four crystalline bismuth titanate materials. Highlights: Black-Right-Pointing-Pointer NaBiO{sub 3} and TiO{sub 2} under hydrothermal conditions allow formation of bismuth titanates. Black-Right-Pointing-Pointer Synthesis of four distint phases has been mapped. Black-Right-Pointing-Pointer Bi LIII-edge XANES shows Bi is reduced to oxidation state +3 in all materials. Black-Right-Pointing-Pointer A new hydrated bismuth titanate pyrochlore has been isolated.

  14. Bismuth pyrochlore thin films for dielectric energy storage

    International Nuclear Information System (INIS)

    Thin films of cubic pyrochlore bismuth zinc niobate, bismuth zinc tantalate, and bismuth zinc niobate tantalate were fabricated using chemical solution deposition. This family of materials exhibited moderate relative permittivities between 55 ± 2 and 145 ± 5 for bismuth zinc tantalate and bismuth zinc niobate, respectively, and low loss tangents on the order of 0.0008 ± 0.0001. Increases in the concentration of the tantalum end member increased the dielectric breakdown strength. For example, at 10 kHz, the room temperature breakdown strength of bismuth zinc niobate was 5.1 MV/cm, while that of bismuth zinc tantalate was 6.1 MV/cm. This combination of a high breakdown strength and a moderate permittivity led to a high discharged energy storage density for all film compositions. For example, at a measurement frequency of 10 kHz, bismuth zinc niobate exhibited a maximum recoverable energy storage density of 60.8 ± 2.0 J/cm3, while bismuth zinc tantalate exhibited a recoverable energy storage density of 60.7 ± 2.0 J/cm3. Intermediate compositions of bismuth zinc niobate tantalate offered higher energy storage densities; at 10 mol. % tantalum, the maximum recoverable energy storage density was ∼66.9 ± 2.4 J/cm3

  15. German energy market 2014

    International Nuclear Information System (INIS)

    In 2014 the German government's primary goal of engaging German power suppliers to step up their production of renewable energy while speeding up energy efficiency improvement measures continued to dominate the debate. The present article provides an updated overview of the German energy market. Following on from last year's edition it gives a condensed synopsis of key indicators of the energy economy. Besides summarising general facts about the energy mix it goes into detail about the following individual energy resources: crude oil, natural gas, brown coal, hard coal, nuclear energy and renewable energies. It also explains current price trends in both the international and domestic markets.

  16. Bismuth( Ⅲ ) Salts: Green Catalysts for Organic Transformations

    Institute of Scientific and Technical Information of China (English)

    C. Le Roux

    2005-01-01

    @@ 1Introduction Bismuth, the heaviest stable element in the periodic table, stands out from other heavy elements (such as mercury, thallium and lead) due to its relatively non-toxic character which confers on bismuth the enviable status of being an eco-friendly element. Therefore, bismuth and its compounds hold considerable promise as useful catalysts for green chemistry. The research presented in this communication is devoted to the applications of bismuth( Ⅲ ) salts as catalysts for organic transformations.After some general comments about bismuth and a short presentation of the various applications of bismuth( Ⅲ ) salts in organic synthesis, this communication will focus on the works done in our research group during the last several years which deals mainly with electrophilic substitutions. When appropriate, some mechanistic details will be given.

  17. German-Chinese wedding

    Energy Technology Data Exchange (ETDEWEB)

    Iken, Joern

    2010-07-01

    German wind power technology is widely regarded as being ahead of its competitors worldwide. Combine this technology with production in China and a renowned designer and you should get a competitive product. (orig.)

  18. German Medical Science ausgezeichnet

    OpenAIRE

    Müller, W.

    2011-01-01

    German Medical Science - das medizinische Publikationsportal von AWMF, DIMDI und ZB MED - wird am 21. Oktober 2011 von der Initiative "Deutschland - Land der Ideen" als "Ausgewählter Ort im Land der Ideen 2011" ausgezeichnet.

  19. German export performance

    OpenAIRE

    Arndt, Sven W.

    1983-01-01

    The Federal Republic of Germany's exports in 1980 represented approximately 23% of GNP. Germany's share of total world exports, however, declined throughout the seventies. What are the factors influencing German export performance? What is the outlook for the future?

  20. West German Ostpolitik and the German Question

    OpenAIRE

    GERT KRELL

    1991-01-01

    The specific problems of West German Ostpolitik during the Cold War and the period of detente have acquired new interest under the current conditions of radical systemic change. The various options pursued by the Federal Republic and their development provide criteria for an evaluation of the future course of the united Germany's foreign policy. The article starts with laying out the basic conditions of the FRG's Ostpolitik and their inherent contradictions: revisionism versus reconciliation,...

  1. German Business in Russia

    Directory of Open Access Journals (Sweden)

    Irakliy D. Gvazava

    2013-01-01

    Full Text Available Since Perestroika German-Russian relationships have been steadily developing fueled by close contacts between the leaders of both countries. Boris Yeltsin and Helmut Kohl, Vladimir Putin and Gerhard Schröder, Dmitry Medvedev and Angela Merkel had friendly relations resulted in some fruitful business projects, intergovernmental economic forums etc. In my article I will consider the activities of German companies in Russia, advantages, barriers and expectations

  2. Electroanalysis of organic compounds at bismuth electrodes: a short review

    OpenAIRE

    Lezi, Nikolitsa; Vyskočil, Vlastimil; Economou, Anastasios; Barek, Jiří

    2012-01-01

    Over the last twelve years, it has been demonstrated that bismuth electrodes have comparable electroanalytical performance to mercury electrodes in the negative potential range. Since the toxicicty of bismuth is lower than that of mercury, bismuth can serve as an alternative “green” electrode material to mercury. However, the great majority of published work at bismuth–based electrodes is concerned with the determination of trace metals by voltammetric techniques with only few applications de...

  3. Electron Paramagnetic Resonance Study of Thermally Treated Bismuth Subgallate

    OpenAIRE

    2014-01-01

    Complex of bismuth, an anti-inflammatory drug, was studied by EPR spectroscopy. The aim of this study was to determine concentrations and properties of free radicals formed during thermal sterilization of bismuth subgallate according to pharmacopoeia norms to optimize its sterilization process. Different temperatures (160°C, 170°C, and 180°C) and times (120 minutes, 60 minutes, and 30 minutes) of sterilization were used. Interactions of bismuth subgallate with DPPH, the model free radical ref...

  4. Stress-driven growth of bismuth nanowires

    Science.gov (United States)

    Cheng, Yang-Tse; Weiner, Anita M.; Wong, Curtis A.; Balogh, Michael P.; Lukitsch, Michael J.

    2003-03-01

    We recently reported that compressive stresses in thin films can be exploited to grow nanowires (Ref.1). Nanowires of bismuth (Bi) with diameters ranging from 30 to 200 nm and lengths up to several millimeters were formed spontaneously at the rate of a few micrometers per second at room temperature on surfaces of freshly grown composite thin films consisting of Bi and chrome-nitride (CrN). The high compressive stress in the composite thin films was shown to be the driving force responsible for the nanowire formation. In this presentation, the effects of stress, composition, and temperature on the growth and structure of bismuth nanowires will be discussed. This method of growing nanowires can also be extended to other material systems. Ref. 1. Yang-Tse Cheng, Anita M. Weiner, Curtis A. Wong, Michael P. Balogh, and Michael J. Lukitsch, Applied Physics Letters 81, 3248 (2002).

  5. Magnetoconductance fluctuations in open bismuth quantum dots

    Science.gov (United States)

    Hackens, B.; Minet, J. P.; Farhi, G.; Crahay, A.; Faniel, S.; Gustin, C.; Bayot, V.

    2002-03-01

    We investigate the low temperature (300 mK - 10 K) magnetoconductance of open circular bismuth quantum dots (diameter: 500 nm). The structures are fabricated using a combination of electron beam lithography, lift off and plasma etching techniques on bismuth thin films evaporated on heated SiO2 substrates. We observe reproducible magnetoconductance fluctuations (UCFs) up to 5T, qualitatively similar to conductance fluctuations evidenced in open quantum dots patterned in high mobility semiconductor heterostructures. In our samples, UCFs are superposed on a slowly varying negative magnetoconductance background. We also observe a sharp conductance maximum centered in B=0, which is reminescent of the spin-orbit induced anti-localisation phenomenon. The behavior of UCFs and of the conductance maximum is discussed as a function of the temperature, thickness and degree of cristallinity of the cavity.

  6. Electrocatalytic activity of bismuth doped silver electrodes

    CERN Document Server

    Amjad, M

    2002-01-01

    Investigation of redox reactions on silver, and bismuth doped silver electrodes in aqueous KOH solutions, by using potentiostatic steady-state polarization technique, has been carried out. The redox wave potential and current displacements along with multiplicity of the latter have been examined. These electrodes were employed for the oxidation of organic molecules such as ethylamine in alkaline media. Subsequently, these electrodes were ranked with respect to their activity for the redox reactions. (author)

  7. Bismuth film electrodes for heavy metals determination

    Science.gov (United States)

    Rehacek, Vlastimil; Hotovy, Ivan; Vojs, Marian; Mika, Fedor

    2007-05-01

    Bismuth film electrodes (BiFEs) have a potential to replace toxic mercury used most frequently for determination of heavy metals (Cd, Pb, Zn) by anodic stripping voltammetry. We prepared a graphite disc electrode (0.5 mm in diameter) from a pencil-lead rod and developed a nitrogen doped diamond-like carbon (NDLC) microelectrode array consisting of 50 625 microdiscs with 3 μm in diameter and interelectrode distances of 20 μm on a highly conductive silicon substrate as a support for BiFEs. The disc graphite BiFE was used for simultaneous determination of Pb(II), Cd(II) and Zn(II) by square wave voltammetry (SWV) in an aqueous solution. We found the optimum bismuth-to-metal concentration ratio in the solution to be 20. The dependence of the stripping responses on the concentration of target metals was linear in the range from 1×10 -8 to 1.2×10 -7 mol/L. Detection limits 2.4×10 -9 mol/L for Pb(II), 2.9×10 -9 mol/L for Cd(II) and 1.2×10 -8 mol/L for Zn(II) were estimated. A bismuth-plated NDLC microelectrode array was used for Pb(II) determination by differential pulse voltammetry (DPV) in an aqueous solution. We found that the stripping current for bismuth-plated NDLC array was linear in the concentration range of Pb(II) from 2×10 -8 to 1.2×10 -7 mol/L. The detection limit 2.2×10 -8 mol/L was estimated from a calibration plot.

  8. Influence of bismuth content on viscosity of lead-bismuth alloy

    International Nuclear Information System (INIS)

    In this paper, viscosities of Pb44.5 Bi55.5 (LBE), Pb60 Bi40, Pb70 Bi30, Pb80 Bi20 and Pb are studied in a certain temperature range above liquidus, the results show that the viscosities of five melts decrease with the increase of temperature. Excepting for pure Pb, anomalous changes in the viscosity values are found in LBE, Pb60 Bi40, Pb70 Bi30 and Pb80 Bi20 in the test temperature range, it is presumed that melts structure occurs at the anomalous point of the viscosity. In the temperature range of 623∼923 K, viscosity value of Pb60 Bi40 is obviously higher than that of the other proportion of lead bismuth alloy, and it increases with the decrease of bismuth content at temperature above 1023 K. The experimental results provide data support for the choice of lead-bismuth hypoeutectic applied in advanced nuclear reactor. (authors)

  9. Flame spray synthesis under a non-oxidizing atmosphere: Preparation of metallic bismuth nanoparticles and nanocrystalline bulk bismuth metal

    International Nuclear Information System (INIS)

    Metallic bismuth nanoparticles of over 98% purity were prepared by a modified flame spray synthesis method in an inert atmosphere by oxygen-deficient combustion of a bismuth-carboxylate based precursor. The samples were characterized by X-ray diffraction, thermal analysis and scanning electron microscopy confirming the formation of pure, crystalline metallic bismuth nanoparticles. Compression of the as-prepared powder resulted in highly dense, nanocrystalline pills with strong electrical conductivity and bright metallic gloss

  10. Spin dynamics of complex oxides, bismuth-antimony alloys, and bismuth chalcogenides

    Science.gov (United States)

    Sahin, Cuneyt

    The emerging field of spintronics relies on the manipulation of electron spin in order to use it in spin-based electronics. Such a paradigm change has to tackle several challenges including finding materials with sufficiently long spin lifetimes and materials which are efficient in generating pure spin currents. This thesis predicts that two types of material families could be a solution to the aforementioned challenges: complex oxides and bismuth based materials. We derived a general approach for constructing an effective spin-orbit Hamiltonian which is applicable to all nonmagnetic materials. This formalism is useful for calculating spin-dependent properties near an arbitrary point in momentum space. We also verified this formalism through comparisons with other approaches for III-V semiconductors, and its general applicability is illustrated by deriving the spin-orbit interaction and predicting spin lifetimes for strained strontium titanate (STO) and a two-dimensional electron gas in STO (such as at the LAO/STO interface). Our results suggest robust spin coherence and spin transport properties in STO related materials even at room temperature. In the second part of the study we calculated intrinsic spin Hall conductivities for bismuth-antimony (BISb) semimetals with strong spin-orbit couplings, from the Kubo formula and using Berry curvatures evaluated throughout the Brillouin zone from a tight-binding Hamiltonian. Nearly crossing bands with strong spin-orbit interaction generate giant spin Hall conductivities in these materials, ranging from 474 ((h/e)O--1cm--1) for bismuth to 96((h/e)O--1cm --1) for antimony; the value for bismuth is more than twice that of platinum. The large spin Hall conductivities persist for alloy compositions corresponding to a three-dimensional topological insulator state, such as Bi0.83Sb0.17. The spin Hall conductivity could be changed by a factor of 5 for doped Bi, or for Bi0.83Sb0.17, by changing the chemical potential by 0.5 e

  11. German Process of Qualification

    International Nuclear Information System (INIS)

    The current German qualification practice uses an envigilated capability demonstration of a NDT method for an inspection task at a specific component. Instead of having a qualification body or the regulators doing the envigilation, an independent third-party agent, the German TU (Technischer Uberwachungsverein) acts as a technical expert contracted by the safety authority. It envigilates the capability demonstration and gives recommendations to the state-authority which is the responsible local authority for every power station. A lot of technical constraints necessary in the qualification procedure are already defined in the German KTA-rules for inservice inspection and the German standards (DIN standards) for inspection techniques applied in nuclear industry. With those prerequisites the German national ENIQ-initiative tries to realise and implement the general principles of the ENIQ-Methodology under the constraints of long term evolved qualification practice. A hardware qualification and a component qualification divided into three categories are presented, followed by qualification procedure and responsibilities, documentation of qualification, qualification of personnel, handling of qualifications conducted in the past. An example is given with the Hardware qualification of the SAPHIR UT-system developed by Siemens/KWU

  12. German energy market 2013

    International Nuclear Information System (INIS)

    The general course projected for the national energy supply in the German federal government's energy concept, namely to expand the use of renewable energy resources while improving energy efficiency, continued to dominate the discussion in 2013. Yet in spite of this many sectors have seen an increase in energy consumption. This is conveyed by the present overview of the German energy market. This year's report once more gives a condensed synopsis with key figures on the German energy economy. As in previous years, the article not only summarises general facts on the energy mix but reports in detail on developments relating to the individual energy resources, i.e. crude oil, natural gas, brown and hard coal, nuclear energy and renewable energies. It also explains price trends in both the international and the domestic markets.

  13. Hall-Effect Thruster Utilizing Bismuth as Propellant

    Science.gov (United States)

    Szabo, James; Gasdaska, Charles; Hruby, Vlad; Robin, Mike

    2008-01-01

    A laboratory-model Hall-effect spacecraft thruster was developed that utilizes bismuth as the propellant. Xenon was used in most prior Hall-effect thrusters. Bismuth is an attractive alternative because it has a larger atomic mass, a larger electron-impact-ionization cross-section, and is cheaper and more plentiful.

  14. Optical spectroscopy of Bismuth-doped pure silica fiber preform

    OpenAIRE

    Razdobreev, Igor,; El Hamzaoui, Hicham; Ivanov, V. Yu; Kustov, E. F.; Capoen, Bruno; Bouazaoui, Mohamed

    2010-01-01

    International audience We report on the optical spectroscopy of monolithic fiber preform prepared from nanoporous bismuth-doped silica glass. The experiments reveal the existence of at least two different types of active centers and clearly demonstrate that the presence in the glass matrix of other dopant is not necessary to obtain the near-IR photoluminescence connected to Bismuth.

  15. Dirty German everyday slang

    CERN Document Server

    Chaffey, Daniel

    2010-01-01

    GET D!RTYNext time you're traveling or just chattin' in German with your friends, drop the textbook formality and bust out with expressions they never teach you in school, including:•Cool slang•Funny insults•Explicit sex terms•Raw swear wordsDirty German teaches the casual expressions heard every day on the streets of Germany:•What's up?Wie geht's?•I'm smashed.Ich bin total angeschickert.•Fuckin' Munich fans.Scheiß München Fans.•That shit reeks.Das riecht aber ü

  16. Bismuth(III) dialkyldithiophosphates: Facile single source precursors for the preparation of bismuth sulfide nanorods and bismuth phosphate thin films

    Energy Technology Data Exchange (ETDEWEB)

    Biswal, Jasmine B. [Department of Chemistry, University of Mumbai, Vidyanagari, Santacruz (East), Mumbai 400098 (India); Garje, Shivram S., E-mail: ssgarje@chem.mu.ac.in [Department of Chemistry, University of Mumbai, Vidyanagari, Santacruz (East), Mumbai 400098 (India); Nuwad, Jitendra; Pillai, C.G.S. [Chemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India)

    2013-08-15

    Two different phase pure materials (Bi{sub 2}S{sub 3} and Bi{sub 2}P{sub 4}O{sub 13}) have been prepared under different conditions using the same single source precursors. Solvothermal decomposition of the complexes, Bi(S{sub 2}P(OR){sub 2}){sub 3} [where, R=Methyl (Me) (1), Ethyl (Et) (2), n-Propyl (Pr{sup n}) (3) and iso-Propyl (Pr{sup i}) (4)] in ethylene glycol gave orthorhombic bismuth sulfide nanorods, whereas aerosol assisted chemical vapor deposition (AACVD) of the same precursors deposited monoclinic bismuth tetraphosphate (Bi{sub 2}P{sub 4}O{sub 13}) thin films on glass substrates. Surface study of the thin films using SEM illustrated the formation of variety of nanoscale morphologies (spherical-, wire-, pendent-, doughnut- and flower-like) at different temperatures. AFM studies were carried out to evaluate quality of the films in terms of uniformity and roughness. Thin films of average roughness as low as 1.4 nm were deposited using these precursors. Photoluminescence studies of Bi{sub 2}P{sub 4}O{sub 13} thin films were also carried out. - Graphical abstract: Solvothermal decomposition of bismuth(III) dialkyldithiophosphates in ethylene glycol gave Bi{sub 2}S{sub 3} nanoparticles, whereas aerosol assisted chemical vapor deposition of these single source precursors deposited Bi{sub 2}P{sub 4}O{sub 13} thin films. Display Omitted - Highlights: • Preparation of phase pure orthorhombic Bi{sub 2}S{sub 3} nanorods and monoclinic Bi{sub 2}P{sub 4}O{sub 13} thin films. • Use of single source precursors for deposition of bismuth phosphate thin films. • Use of solvothermal decomposition and AACVD methods. • Morphology controlled synthesis of Bi{sub 2}P{sub 4}O{sub 13} thin films. • Bi{sub 2}S{sub 3} nanorods and Bi{sub 2}P{sub 4}O{sub 13} thin films using same single source precursors.

  17. A case of bismuth intoxication with irreversible renal damage

    Directory of Open Access Journals (Sweden)

    Erden A

    2013-11-01

    Full Text Available Abdulsamet Erden, Samet Karahan, Kadir Bulut, Mustafa Basak, Tuncay Aslan, Ali Cetinkaya, Hatice Karagoz, Deniz Avci Internal Medicine Department, Kayseri Training and Research Hospital, Kayseri, Turkey Abstract: Bismuth is a chemical element symbolized as Bi and is a trivalent poor metal, which chemically resembles arsenic and antimony. Colloidal bismuth subcitrate (CBS and bismuth subsalicylate are the bismuth salts widely used in the treatment of peptic ulcers, functional dyspepsia, and chronic gastritis. Intoxications with CBS are rare. In a few case reports, acute renal failure was described, but the literature review revealed no chronic renal failure related to CBS intoxication. In this case report we present a 21-year old female with chronic renal failure after a one year follow-up of CBS intoxication. Keywords: acute renal failure, bismuth, intoxication, chronic renal failure

  18. An evaluated neutronic data file for bismuth

    International Nuclear Information System (INIS)

    A comprehensive evaluated neutronic data file for bismuth, extending from 10-5 eV to 20.0 MeV, is described. The experimental database, the application of the theoretical models, and the evaluation rationale are outlined. Attention is given to uncertainty specification, and comparisons are made with the prior ENDF/B-V evaluation. The corresponding numerical file, in ENDF/B-VI format, has been transmitted to the National Nuclear Data Center, Brookhaven National Laboratory. 106 refs., 10 figs., 6 tabs

  19. Electron Paramagnetic Resonance Study of Thermally Treated Bismuth Subgallate

    Directory of Open Access Journals (Sweden)

    Paweł Ramos

    2014-01-01

    Full Text Available Complex of bismuth, an anti-inflammatory drug, was studied by EPR spectroscopy. The aim of this study was to determine concentrations and properties of free radicals formed during thermal sterilization of bismuth subgallate according to pharmacopoeia norms to optimize its sterilization process. Different temperatures (160°C, 170°C, and 180°C and times (120 minutes, 60 minutes, and 30 minutes of sterilization were used. Interactions of bismuth subgallate with DPPH, the model free radical reference, were checked. g-Factors, amplitudes (A, integral intensities (I, and linewidths (ΔBpp were obtained. Integral intensities were obtained by double integration of the first-derivative EPR lines. The influence of microwave power in the range of 2.2–70 mW on shape and parameters of the EPR spectra was examined. Thermal sterilization produced free radicals in bismuth subgallate in all tested cases. Strong interactions with free radicals were pointed out for all the analysed samples containing bismuth independent of sterilization conditions. Optimal conditions of thermal sterilization for bismuth subgallate with the lowest free radical formation are temperature 170°C and time of heating 60 minutes. Strong dipolar interactions exist in thermally sterilized bismuth subgallate. EPR spectroscopy is a useful method of examination of thermal sterilization conditions.

  20. Electron paramagnetic resonance study of thermally treated bismuth subgallate.

    Science.gov (United States)

    Ramos, Paweł; Pilawa, Barbara

    2014-01-01

    Complex of bismuth, an anti-inflammatory drug, was studied by EPR spectroscopy. The aim of this study was to determine concentrations and properties of free radicals formed during thermal sterilization of bismuth subgallate according to pharmacopoeia norms to optimize its sterilization process. Different temperatures (160°C, 170°C, and 180°C) and times (120 minutes, 60 minutes, and 30 minutes) of sterilization were used. Interactions of bismuth subgallate with DPPH, the model free radical reference, were checked. g-Factors, amplitudes (A), integral intensities (I), and linewidths (ΔB pp) were obtained. Integral intensities were obtained by double integration of the first-derivative EPR lines. The influence of microwave power in the range of 2.2-70 mW on shape and parameters of the EPR spectra was examined. Thermal sterilization produced free radicals in bismuth subgallate in all tested cases. Strong interactions with free radicals were pointed out for all the analysed samples containing bismuth independent of sterilization conditions. Optimal conditions of thermal sterilization for bismuth subgallate with the lowest free radical formation are temperature 170°C and time of heating 60 minutes. Strong dipolar interactions exist in thermally sterilized bismuth subgallate. EPR spectroscopy is a useful method of examination of thermal sterilization conditions. PMID:25525421

  1. Determining the background levels of bismuth in tissues of wild game birds: a first step in addressing the environmental consequences of using bismuth shotshells

    International Nuclear Information System (INIS)

    Bismuth shotshells have been approved as a 'nontoxic' alternative to lead in North America. Approval was based on a limited number of studies; even background levels of bismuth in wildfowl were unknown. We report on the concentration of bismuth (and lead) in muscle and liver tissues of wildfowl (Anas platyrhynchos, Anas acuta, Anas crecca, Branta canadensis, Chen caerulescens) harvested with lead shotshell. Average liver-bismuth levels detected in the present study (e.g., teal, 0.05 μg/g dw; mallard, 0.09 μg/g dw) suggest analytical error in other studies examining the effects of bismuth in birds. Significant positive relationships between bismuth- and lead-tissue levels for muscle when all species were combined (and for B. canadensis and C. caerulescens separately) can be explained by noting that bismuth is a contaminant of lead. Thus, more research is recommended to confirm the appropriateness of bismuth as a 'nontoxic' shot alternative

  2. On the use of tapered bismuth germanate crystals in positron emission tomography

    International Nuclear Information System (INIS)

    An analytical model of gamma ray transport within the detectors of a positron camera, based on exponential absorption, has been developed and verified experimentally. The model has been used to study the intrinsic resolution obtained with scintillation detectors that have had their front corners removed. It is concluded that for crystals greater than 0.8 cm wide, tapering the face of the detector results in improved uniformity of resolution. Thus it is useful for medium and low resolution scanners. In these cases, it has been found that the loss in sensitivity resulting from the use of tapered crystals is less than that which occurs when septa are placed between crystals to achieve comparable uniformity of resolution. It has also been established that, in some instances, reducing the length of the detectors results in a more uniform resolution than that obtained with tapered crystals, although this leads to a loss in ring sensitivity and an increase in the detected scatter fraction. (orig.)

  3. Visible to infrared low temperature photoluminescence of rare earth doped bismuth germanate crystals.

    Science.gov (United States)

    Canimoglu, A; Ayvacikli, M; Karabulut, Y; Karali, T; Can, N

    2016-05-01

    In this paper, the influence of a series of rare earth (Eu, Tm, Nd) and Cr ion doping on the optical properties of BGO was investigated by means of photoluminescence (PL) from visible to IR region in the 10-300K temperature range using different types of detectors, namely, photomultiplier tube (PMT), InGaAs (IGA), and Si. Several samples were investigated having dopants concentrations of 0.3wt%Nd, 0.4wt%Tm, 0.06wt% Cr and 3ppm Eu. The PL spectra of the samples showed different luminescence behaviour which is assigned to the 4f intra shell transition from rare earth ions. The temperature dependence of the PL from rare earth doped BGO crystals is also examined. PMID:26943903

  4. Photoluminescence of Bismuth Germanate Phosphors with a Silica-shell Structure

    Science.gov (United States)

    Oviedo, M. J.; Han, J. K.; Contreras, O.; Macedo, Z. S.; Hirata, G. A.; McKittrick, J.

    An intense bluish-white emitting phosphor Bi4Ge3O12 (BGO) was synthesized by tartaric acid-assisted solgel method and covered with a SiO2 nanolayer by the sol-gel method. The cubic crystal structure of BGO was confirmed by X-ray diffraction. Transmission electron microscopy analysis revealed the particle size to be in the range of 6-20 nm. Under excitation with 4.3 eV photons the BGO powders showed a PL contribution centered at 2.43 eV that corresponds to the typical BGO luminescence associated with 3P1à1S0 of Bi3+ electron transitions. Radioluminescence measurements showed the predominant emission centered at 2.43 eV due to the intra-ionic Bi3+ transitions. The PL emission of the silica coated BGO nanoparticles presented a luminescence enhancement of more than 200% compared with the uncoated nanoparticles. This enhancement in photoluminescence is proposed to be related to the reflectivity (refractive index) between air-silica-BGO layers.

  5. Dynamic positron emission tomography in man using small bismuth germanate crystals

    International Nuclear Information System (INIS)

    Primary considerations for the design of positron emission tomographs for medical studies in humans are the need for high imaging sensitivity, whole organ coverage, good spatial resolution, high maximum data rates, adequate spatial sampling with minimum mechanical motion, shielding against out of plane activity, pulse height discrimination against scattered photons, and timing discrimination against accidental coincidences. We discuss the choice of detectors, sampling motion, shielding, and electronics to meet these objectives

  6. [German ophthalmologists and NSDAP

    Science.gov (United States)

    Rohrbach, Jens Martin

    2008-01-01

    Approximately 40-45 % of all German physicians joined the National Socialist German Workers Party (NSDAP) until 1945. Reasons for party membership are manifold and still a matter of debate. Very likely, the extraordinary high representation of medical doctors in the NSDAP was rather a result of active entry than recruitment by the party. There are only few data concerning the willingness of ophthalmologists to become a party member ("Parteigenosse", "Pg"). According to the list of University teachers in Germany ("Hochschullehrerkarte"; Federal Archive, Berlin), the list of the members of the German Ophthalmological Society (DOG) of 1934 and especially the list of NSDAP-members (Federal Archive, Berlin) the following conclusions can be drawn: 1. Directors of German University eye hospitals (chairmen) were members of the NSDAP with a frequency of 23% in 1933 and 48% in 1938 as well as in 1943. The motivation for joining the party was most likely the perspective of acceleration of the academic career. 2. "Only" 30% of the ophthalmologists working in private praxis were "Pg" (until 1945). 3. Both chairmen and ophthalmologists in private praxis were equally hindered to join the NSDAP between May 1st 1933 and May 1st 1937 when the party temporarily stopped registration. 4. The majority of ophthalmologists who joined the NSDAP were born between 1880 and 1900 and thus had taken part in World War I as soldiers or had experienced the times of need after WW I. Only few ophthalmologists succeeded in the NS-hierarchy and probably only one ophthalmologist, Walther Löhlein from Berlin, came in personal contact with Adolf Hitler who was constantly in fear for his sight after his eye injury in October 1918. The "Law for the prevention of genetically disabled offsprings" ("Gesetz zur Verhütung erbkranken Nachwuchses") from July 14th, 1933 separated ophthalmologists into two parties: those advocating sterilization to a high degree and those recommending sterilization only

  7. Hierarchical bismuth phosphate microspheres with high photocatalytic performance

    Energy Technology Data Exchange (ETDEWEB)

    Pei, Lizhai; Wei, Tian; Lin, Nan; Yu, Haiyun [Anhui University of Technology, Ma' anshan (China). Key Laboratory of Materials Science and Processing of Anhui Province

    2016-05-15

    Hierarchical bismuth phosphate microspheres have been prepared by a simple hydrothermal process with polyvinyl pyrrolidone. Scanning electron microscopy observations show that the hierarchical bismuth phosphate microspheres consist of nanosheets with a thickness of about 30 nm. The diameter of the microspheres is about 1 - 3 μm. X-ray diffraction analysis shows that the microspheres are comprised of triclinic Bi{sub 23}P{sub 4}O{sub 44.5} phase. The formation of the hierarchical microspheres depends on polyvinyl pyrrolidone concentration, hydrothermal temperature and reaction time. Gentian violet acts as the pollutant model for investigating the photocatalytic activity of the hierarchical bismuth phosphate microspheres under ultraviolet-visible light irradiation. Irradiation time, dosage of the hierarchical microspheres and initial gentian violet concentration on the photocatalytic efficiency are also discussed. The hierarchical bismuth phosphate microspheres show good photocatalytic performance for gentian violet removal in aqueous solution.

  8. Bismuth electrodes, an alternative in stripping voltammetry

    International Nuclear Information System (INIS)

    The heavy metals are known as highly toxic contaminants, the processes carried out in industry contribute that finally they remain dispersed in effluents and sewage, doing part of the food chain. The importance of controlling the levels of these heavy metals has become an international policy, so it has generated interest in developing new analytical methodologies for its determination [1, 2, 3, 4]. The stripping voltammetry has been considered as a family of electro-sensitive analytical techniques useful for the determination of trace levels of many metals in environmental, clinical and industrial samples [3, 4]. This work presents an overview of these bismuth-based electrodes which were introduced around 2000, which have interesting characteristics for detection of heavy metals and which represent an alternative to mercury electrodes

  9. Bismuth electrodes, an alternative in stripping voltammetry

    Science.gov (United States)

    Barón-Jaimez, J.; Joya, M. R.; Barba-Ortega, J.

    2013-11-01

    The heavy metals are known as highly toxic contaminants, the processes carried out in industry contribute that finally they remain dispersed in effluents and sewage, doing part of the food chain. The importance of controlling the levels of these heavy metals has become an international policy, so it has generated interest in developing new analytical methodologies for its determination [1, 2, 3, 4]. The stripping voltammetry has been considered as a family of electro-sensitive analytical techniques useful for the determination of trace levels of many metals in environmental, clinical and industrial samples [3, 4]. This work presents an overview of these bismuth-based electrodes which were introduced around 2000, which have interesting characteristics for detection of heavy metals and which represent an alternative to mercury electrodes.

  10. High magnetoresistance in inhomogeneous bismuth microwires

    International Nuclear Information System (INIS)

    The present paper describes investigation of the dependence of magnetoresistance of microwires made of semimetal or semiconductor materials with high electric mobility doped with impurities introduced in the form of deposits at solidification. Till present it has been assumed that microscopic inhomogeneity in semimetals or semiconductors leads to a decrease of mobilities due to additional dispersion of charge carriers on impurities. Wolfe et al. have shown that impurities in the material with high mobility lead to an increase of mobilities due to geometric effect. In our case it is shown that presence of magnetic impurities in bismuth semimetal characterized by high mobility leads to an increase of magnetoresistance. This increase is very important for the technology of magnetic field converters and especially for application of high velocities of record of a magnetic head with a high capability of magnetic record. (authors)

  11. Platinum-Bismuth Bimetallic Catalysts: Synthesis, Characterization and Applications

    OpenAIRE

    Saucedo, Jose A, Jr; Xiao, Yang; Varma, Arvind

    2015-01-01

    Bimetallic catalysts have been explored and shown to exhibit unique characteristics which are not present in monometallic catalysts. Platinum is well known as an effective catalyst for oxidation and reduction reactions, and it can be made more effective when bismuth is introduced as a promotor. Thus, the effectiveness of the Pt-Bi catalyst was demonstrated in prior work. What is not clear, however, is the mechanism behind the catalyst function; why addition of bismuth to platinum decreases de...

  12. Electron cooling and Debye-Waller effect in photoexcited bismuth

    OpenAIRE

    Arnaud, B.; Giret, Y.

    2012-01-01

    By means of first principles calculations, we computed the effective electron-phonon coupling constant $G_0$ governing the electron cooling in photoexcited bismuth. $G_0$ strongly increases as a function of electron temperature, which can be traced back to the semi-metallic nature of bismuth. We also used a thermodynamical model to compute the time evolution of both electron and lattice temperatures following laser excitation. Thereby, we simulated the time evolution of (1 -1 0), (-2 1 1) and...

  13. Piezoelectric bismuth titanate ceramics for high temperature applications

    OpenAIRE

    Shulman, Holly Sue; Setter, Nava

    2005-01-01

    Bismuth titanate (Bi4Ti3O12) shows promise in piezoelectric applications in a temperature range (300-600 °C) which is not well served by standard piezoelectric ceramics. The proposal to use bismuth titanate ceramics for these applications has a major flaw, namely that the high electrical conductivity precludes the efficient polarization of these materials in an electric field. The degree of polarization is critical since it is directly related to the piezoelectric response. In addition, once ...

  14. Studies on bismuth carboxylates—synthesis and characterization of a new structural form of bismuth(III) dipicolinate

    Indian Academy of Sciences (India)

    O Anjaneyulu; K C Kumara Swamy

    2011-03-01

    Synthesis and X-ray structure of a new bismuth dipicolinate cooordination polymer, {[Bi((2,6-O2C)2C5H3N)((2-HO2C-6-O2C)C5H3N)(H2O)]2.5H2O} (7) are presented. Compound 7 has dimeric units with a Bi2O2 skeleton that are linked by additional weak Bi-O interactions leading to a polymeric structure. The overall coordination number at bismuth is 9 [two Bi-N and seven Bi-O bonds]. New routes to a second crystalline modification (4′) of the previously reported coordination polymer, bismuth tris(picolinate), [Bi(2-O2C-C5H4N)3] (4), are described; bond parameters in the two crystalline forms (4 and 4′) are compared. In both the compounds 4′ and 7, bismuth has a distorted tricapped trigonal prismatic geometry.

  15. The German drought monitor

    Science.gov (United States)

    Zink, Matthias; Samaniego, Luis; Kumar, Rohini; Thober, Stephan; Mai, Juliane; Schäfer, David; Marx, Andreas

    2016-07-01

    The 2003 drought event in Europe had major implications on many societal sectors, including energy production, health, forestry and agriculture. The reduced availability of water accompanied by high temperatures led to substantial economic losses on the order of 1.5 Billion Euros, in agriculture alone. Furthermore, soil droughts have considerable impacts on ecosystems, forest fires and water management. Monitoring soil water availability in near real-time and at high-resolution, i.e., 4 × 4 km2, enables water managers to mitigate the impact of these extreme events. The German drought monitor was established in 2014 as an online platform. It uses an operational modeling system that consists of four steps: (1) a daily update of observed meteorological data by the German Weather Service, with consistency checks and interpolation; (2) an estimation of current soil moisture using the mesoscale hydrological model; (3) calculation of a quantile-based soil moisture index (SMI) based on a 60 year data record; and (4) classification of the SMI into five drought classes ranging from abnormally dry to exceptional drought. Finally, an easy to understand map is produced and published on a daily basis on www.ufz.de/droughtmonitor. Analysis of the ongoing 2015 drought event, which garnered broad media attention, shows that 75% of the German territory underwent drought conditions in July 2015. Regions such as Northern Bavaria and Eastern Saxony, however, have been particularly prone to drought conditions since autumn 2014. Comparisons with historical droughts show that the 2015 event is amongst the ten most severe drought events observed in Germany since 1954 in terms of its spatial extent, magnitude and duration.

  16. Electricity: the German example

    International Nuclear Information System (INIS)

    The author proposes some comments on the content of the Energiewende, i.e. the definition of the energy transition in Germany which aims at producing and consuming a green energy, without carbon nor nuclear. He comments the German energy mix for 2010 in terms of electricity production per origin (nuclear, coal and lignite, gas, oil, wind, solar photovoltaic, other renewable sources) and of installed capacities per origin. He notices that gas and coal still have a major weight in this mix, and discusses the content of a scenario based 100 per cent renewable energies as it has been studied by the Fraunhofer Institute, notably in terms of production level and of costs

  17. Crash Testing German Banks

    OpenAIRE

    Klaus Duellmann; Martin Erdelmeier

    2009-01-01

    In this paper we stress-test credit portfolios of twenty-eight German banks based on a Merton-type multifactor credit-risk model. The stress scenario is an economic downturn in the automobile sector. Although the percentage of loans in the automobile sector is relatively low for all banks in the sample, the expected loss conditional on the stress event increases substantially by 70–80 percent for the total portfolio. This result confirms the need to account for hidden sectoral concentration r...

  18. German Soldier and German Unity: Political Foundations of the German Armed Forces

    OpenAIRE

    Abenheim, Donald

    1991-01-01

    The unification of Germany has transformed the political-military landscape of central Europe. Not the least of the issues raised by the union of the Federal Republic and the German Democratic Republic is the fate of the professional soldier in a united Germany. The present study analyzes the concept of military professionalism in the setting of the two former German states, placing emphasis on the political-ethical foundations of the West German armed forces and the political mechanisms of t...

  19. Synthesis and Characterization of High-Purity Bismuth Nanowires via Seed-Assisted Growth Approach

    Science.gov (United States)

    Mu, Xin; Zhao, Wen-Yu; He, Dan-Qi; Zhou, Hong-Yu; Zhu, Wan-Ting; Zhang, Qing-Jie

    2015-06-01

    Nanowires are considered as high-performance thermoelectric materials with large Seebeck coefficients due to quantum confinement and low thermal conductivity because of enhanced boundary scattering of phonons. In this work, a seed-assisted growth method has been developed to synthesize high-purity bismuth nanowires. The bismuth seeds were first synthesized by reducing BiCl3 in the ice water with NaBH4. The high-purity bismuth nanowires about 40-50 nm in diameter and several tens of micrometers in length were then grown on bismuth seeds by reducing NaBiO3 with ethylene glycol. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were employed to characterize the crystal structure, microstructure, and growth direction of the bismuth seeds and nanowires. The effects of temperature, reductant, and bismuth seeds template on the microstructures of the bismuth nanowires were also investigated. The synthesis conditions of bismuth seeds and nanowires were optimized. The selected area electron diffraction pattern confirms that the growth direction of bismuth nanowires is parallel to [] direction. It was discovered that high-purity bismuth nanowires with high aspect ratio can be synthesized by precisely controlling the temperature to adjust the nucleation rate of the bismuth nuclei, selecting the appropriate reductant to maintain a low nucleation rate, and using bismuth seeds as the template of the epitaxial growth of the bismuth nuclei.

  20. The German pressure vessel code

    International Nuclear Information System (INIS)

    The philosophy and the safety aspects of the German pressure vessel code is summarised. Emphasis is laid upon material selection, design, manufacture and inspection. The AD specifications, which are embedded in the German regulation for the prevention of accidents 'Pressure Vessels' are compiled primarily to give a measure of safety to the average plant. The possible types of failure are discussed in connection with design aspects. It is shown in detail how the AD specifications count for inelastic material behaviour. A comparison is also made between the German code and the ASME boiler and pressure vessel code. Comparatively, the allowable stresses due to the German code are higher, leading to thinner walls in many cases. This is compensated for by rigorous inspection and non-destructive testing during manufacture. Regular examinations round up the system of safety. It is concluded that the German code gives a high degree of safety and flexibility to the manufacturer. (author)

  1. German visits to CERN

    CERN Multimedia

    2007-01-01

    State secretary to Germany's Federal Ministry of Education and Research, Frieder Meyer-Krahmer, with CERN's Director-General Robert Aymar.On 21 February, Professor Frieder Meyer-Krahmer, State Secretary to Germany's Federal Ministry of Education and Research, came to CERN. He visited the ALICE and ATLAS experiments and the computing centre before meeting the CERN's Director-General, some German physicists and members of the top management. The Minister of Science, Research and the Arts of the Baden-Württemberg regional government, Peter Frankenberg, and CERN's Director-General, Robert Aymar, signing an agreement on education. In the background: Sigurd Lettow, CERN's Director of Finance and Human Resources, and Karl-Heinz Meisel, Rector of the Fachhochschule Karlsruhe. The Minister of Science, Research and the Arts of the Baden-Württemberg regional government, Prof. Peter Frankenberg, visited CERN on 23 February. He was accompanied by the Rector of the Fachhochschule Karlsruhe, Prof. Karl-Heinz Meisel, and b...

  2. German process of qualification

    International Nuclear Information System (INIS)

    In the course of the performed general qualification of the SAPHIR system neither the inspection technique (in accordance with KTA 3201.4) nor the manipulation technique were new and needed a qualification. Therefore, the qualification trials focussed on the functional proof of the phased array technique, the co-operation of the subsystems and the handling and evaluation of inspection results. The full qualification process for routine operation in the region of the German regulators was therefore completed during several days. This is rather effective in economical sense and flexible in terms of adaptation to other qualification tasks. Qualification for those specific inspection tasks can focus on the reliability and efficiency of the used techniques and rely on the general qualification by arguing in the technical Justification. (orig.)

  3. Treatment of ulcerative reflux oesophagitis with colloidal bismuth subcitrate in combination with cimetidine.

    OpenAIRE

    Borkent, M V; Beker, J A

    1988-01-01

    Twenty patients took part in a controlled double blind study comparing the efficacy of colloidal bismuth and cimetidine (800 mg at night) with cimetidine alone in the treatment of ulcerative reflux oesophagitis. Colloidal bismuth 120 mg was administered through an intraoesophageal tube four times a day. Cimetidine with colloidal bismuth gives significantly (p less than 0.001) better results than cimetidine alone. Of 10 patients treated with cimetidine and bismuth, seven had no endoscopic sign...

  4. The German Drought Monitor

    Science.gov (United States)

    Marx, Andreas; Zink, Matthias; Pommerencke, Julia; Kumar, Rohini; Thober, Stephan; Samaniego, Luis

    2015-04-01

    Soil moisture droughts reduce the amount of water available to plant growth potentially leading e.g. to crop failure or increased forest fire risk. The threat of human livelihoods in developing countries and large economic losses in developed ones are severe consequences of these events. Monitoring the current state of soil water content allows to improve water management to mitigate the associated damages. Since summer 2014, the German Drought Monitor (GDM, available at: www.ufz.de/droughtmonitor) has been established using an operational hydrological modeling system, which consists of 3 steps: (1) the daily download of meteorological forcing data, consistency check and interpolation of this data, (2) running the mesoscale Hydrologic Model (mHM; Samaniego et al. 2010) and saving the state variables at the end of the model run as restart-file for the next days run, and (3) calculation of the soil moisture index (SMI, Samaniego et al. 2013, JHM) and visualization of the drought data. The hydrological model mHM was used to generate daily soil moisture fields for the period 1954-2013 over the entire area of Germany at a high spatial resolution of 4 x 4 km². The model requires daily precipitation, temperature, and potential evapotranspiration as forcing. A three-layer soil scheme was used to model the soil moisture dynamics over the entire root zone depth. Based on the 60 year simulation of soil moisture, the frequency distributions have been calculated for each grid cell to derive the soil moisture index. In this beta version, we do a monthly online update of the SMI. Furthermore, a trend analysis of drought events for 69 German subregions since 1954 was conducted. It showed that for most parts of Germany, the frequency of abnormally dry conditions increased while the stronger drought situations with SMIindicators shall be provided, and how the information and data shall be presented and distributed.

  5. Optical properties of bismuth-doped SiO2- or GeO2-based glass core optical fibers

    CERN Document Server

    Firstova, Elena G

    2015-01-01

    A detailed study of optical properties of bismuth-doped fibers based on SiO2 and GeO2 glasses containing no other dopants has been carried out. To provide important information about spectroscopic properties of IR bismuth-related active centers (BAC) the excitation-emission fluorescence spectra for a spectral region of 220-2000 nm have been measured. The obtained three-dimensional spectra have been presented for different host glass compositions: silicate, germanate, aluminosilicate and phosphosilicate. Energy-level configuration and main radiative transitions associated with BACs in GeO2 and SiO2 glasses have been revealed. Fluorescence lifetime analysis of the basic radiative transitions of BAC have been carried out. It has been shown that the energy-level schemes of BAC-Si and BAC-Ge (BAC associated with silicon and germanium, respectively) are similar, corresponding BAC-Ge energy levels lying 10-16% lower than those of BAC-Si. It has been determined that BAC-Si, BAC-Ge and BAC-Si, BAC-P can exist simultan...

  6. Ultrasonication of Bismuth Telluride Nanocrystals Fabricated by Solvothermal Method

    Science.gov (United States)

    Chu, Sang-Hyon; Choi, Sang H.; Kim, Jae-Woo; King, Glen C.; Elliott, James R.

    2006-01-01

    The objective of this study is to evaluate the effect of ultrasonication on bismuth telluride nanocrystals prepared by solvothermal method. In this study, a low dimensional nanocrystal of bismuth telluride (Bi2Te3) was synthesized by a solvothermal process in an autoclave at 180 C and 200 psi. During the solvothermal reaction, organic surfactants effectively prevented unwanted aggregation of nanocrystals in a selected solvent while controlling the shape of the nanocrystal. The atomic ratio of bismuth and tellurium was determined by energy dispersive spectroscopy (EDS). The cavitational energy created by the ultrasonic probe was varied by the ultrasonication process time, while power amplitude remained constant. The nanocrystal size and its size distribution were measured by field emission scanning electron microscopy (FESEM) and a dynamic light scattering system. When the ultrasonication time increased, the average size of bismuth telluride nanocrystal gradually increased due to the direct collision of nanocrystals. The polydispersity of the nanocrystals showed a minimum when the ultrasonication was applied for 5 min. Keywords: bismuth telluride, nanocrystal, low-dimensional, ultrasonication, solvothermal

  7. Laser Spectroscopy of Neutron Rich Bismuth Isotopes

    CERN Multimedia

    2002-01-01

    %IS344 :\\\\ \\\\ The aim of the experiment is to measure the optical isotope shifts and hyperfine structures of bismuth isotopes across the N=126 shell closure in order to extract the change in mean square charge radii ($\\delta\\langle r^{2}\\rangle$) and static moments. These include the first isotones of lead to be measured directly above the shell closure and will provide new information on the systematics of the kink ($\\delta\\langle r^{2}\\rangle)$ seen in the lead isotopic chain. After two very successful runs the programme has been extended to include the neutron deficient isotopes below $^{201}$Bi to study the systematics across the $i_{13/2}$ neutron sub-shell closure at N=118.\\\\ \\\\ During the initial 2 runs (9 shifts) the isotope shifts and hyperfine structures of three new isotopes, $ ^{210,212,213}$Bi and the 9$^{-}$ isomer of $^{210}$Bi have been measured. The accuracy of the previous measurements of $^{205,206,208}$Bi have been greatly improved. The samples of $ ^{208,210,210^{m}}$Bi were prepared by c...

  8. Ultrasound in lead-bismuth eutectic

    International Nuclear Information System (INIS)

    The Belgian Nuclear Research Centre (SCK.CEN) is in the process of designing MYRRHA, a new multi-purpose irradiation facility to replace the ageing BR2. MYRRHA is a fast spectrum reactor cooled with lead-bismuth eutectic (LBE). As liquid metal is opaque to visual light, ultrasonic measurement techniques are selected to fulfill essential tasks that, according to our assessment, will be demanded by licensing authorities, in particular: fuel assembly identification and localization of a lost fuel assembly. To that end, a considerable research effort at SCK.CEN is devoted to study ultrasonic propagation in LBE. As ultrasonic experiments in LBE are elaborate and expensive to set up, we are particularly interested in to what extent experiments in water can be extrapolated to LBE - one of the main focuses of this article. We describe and present results of a first experiment with this goal which shows that the signal to noise ratio is better in LBE and that we even see small diffuse reflections up to 40 deg. off normal. On the other hand, we do not see internal reflections in stainless steel objects in LBE which we do in water. Therefore, we conclude that experiments in water can be used to validate algorithms for LBE on the condition that they do not rely on internal reflections. We also present solutions to tackle the essential tasks: fuel assembly identification and lost object localization. The requirements for the ultrasonic equipment implementing these solutions are also discussed. (authors)

  9. Use of Russian technology of ship reactors with lead-bismuth coolant in nuclear power

    International Nuclear Information System (INIS)

    The experience of using lead-bismuth coolant in Russian nuclear submarine reactors has been presented. The fundamental statements of the concept of using the reactors cooled by lead-bismuth alloy in nuclear power have been substantiated. The results of developments for using lead bismuth coolant in nuclear power have been presented. (author)

  10. 40 CFR 471.10 - Applicability; description of the lead-tin-bismuth forming subcategory.

    Science.gov (United States)

    2010-07-01

    ...-tin-bismuth forming subcategory. 471.10 Section 471.10 Protection of Environment ENVIRONMENTAL... POINT SOURCE CATEGORY Lead-Tin-Bismuth Forming Subcategory § 471.10 Applicability; description of the lead-tin-bismuth forming subcategory. This subpart applies to discharges of pollutants to waters of...

  11. Prognostic Value of Bismuth Typing and Modified T-stage in Hilar Cholangiocarcinoma

    Directory of Open Access Journals (Sweden)

    Shengen Yi

    2015-01-01

    Conclusion: The majority of our patients with HCC were characterized as Subtype IV in Bismuth typing and Stage T3 in modified T-stage. Both Bismuth typing and modified T-stage showed prognostic value in HCC. Compared with Bismuth typing, modified T-stage is a better indicator of the resectability of HCC.

  12. Phase transitions in the Hubbard model for the bismuth nickelate

    Science.gov (United States)

    Kojima, Shoya; Nasu, Joji; Koga, Akihisa

    2016-07-01

    We study low temperature properties of the Hubbard model for the bismuth nickelate, where degenerate orbitals in the nickel ions and a single orbital in the bismuth ions are taken into account, combining dynamical mean-field theory with the continuous-time quantum Monte Carlo method. We discuss the effect of the attractive interactions to mimic the valence skipping phenomenon in the bismuth ions. We demonstrate how the charge and magnetically ordered states are stable against thermal fluctuations. It is furthermore clarified that the ferromagnetically ordered and orbital ordered states are stabilized due to the presence of the orbital degeneracy at low temperatures. The crossover between metallic and insulating states is also discussed.

  13. Inexpensive laser-induced surface modification in bismuth thin films

    International Nuclear Information System (INIS)

    Highlights: • Laser-induced microbumps were formed on bismuth films using a simple, low-cost, laser setup. • The patterns, similar to those typically obtained with high-power lasers, were characterized. • Control of laser ablation conditions is critical in the fabrication of surface microbumps. - Abstract: In this work, we present results on texturing a 500 nm thick bismuth film, deposited by sputtering onto a glass slide using a low-cost homemade, near-infrared pulsed laser platform. A 785 nm laser diode of a CD–DVD pickup head was precisely focused on the sample mounted on a motorized two-axis translation stage to generate localized surface microbumps on the bismuth films. This simple method successfully transferred desired micropatterns on the films in a computer-numerical control fashion. Irradiated zones were characterized by atomic force microscopy and scanning electron microscopy. It was observed that final results are strongly dependent on irradiation parameters

  14. Inexpensive laser-induced surface modification in bismuth thin films

    Energy Technology Data Exchange (ETDEWEB)

    Contreras, A. Reyes [Facultad de Ciencias, Universidad Autónoma del Estado de México, Carretera Toluca, Ixtlahuaca Kilómetro 15.5, C.P. 50200 Edo. de México (Mexico); Hautefeuille, M., E-mail: mathieu_h@ciencias.unam.mx [Facultad de Ciencias, Universidad Nacional Autónoma de México, Avenida Universidad 3000, Circuito Exterior S/N, Coyoacán, Ciudad Universitaria, C.P. 04510 D.F. Mexico (Mexico); García, A. Esparza [Fotofísica y Películas Delgadas, Departamento de Tecnociencias, CCADET-UNAM, Circuito exterior s/n C.P. 04510 Cd. Universitaria, D.F. Mexico (Mexico); Mejia, O. Olea [Centro Conjunto de Investigación en Química Sustentable UAEM-UNAM, Carretera Toluca-Atlacomulco, Km 14.5, Unidad El Rosedal, 50200 San Cayetano, Estado de México (Mexico); López, M.A. Camacho [Facultad de Química, Universidad Autónoma del Estado de México, Tollocan s/n, esq. Paseo Colón, Toluca, Estado de México 50110 (Mexico)

    2015-05-01

    Highlights: • Laser-induced microbumps were formed on bismuth films using a simple, low-cost, laser setup. • The patterns, similar to those typically obtained with high-power lasers, were characterized. • Control of laser ablation conditions is critical in the fabrication of surface microbumps. - Abstract: In this work, we present results on texturing a 500 nm thick bismuth film, deposited by sputtering onto a glass slide using a low-cost homemade, near-infrared pulsed laser platform. A 785 nm laser diode of a CD–DVD pickup head was precisely focused on the sample mounted on a motorized two-axis translation stage to generate localized surface microbumps on the bismuth films. This simple method successfully transferred desired micropatterns on the films in a computer-numerical control fashion. Irradiated zones were characterized by atomic force microscopy and scanning electron microscopy. It was observed that final results are strongly dependent on irradiation parameters.

  15. Characterization of bismuth nanospheres deposited by plasma focus device

    International Nuclear Information System (INIS)

    A new method for producing thin layer of bismuth nanospheres based on the use of low energy plasma focus device is demonstrated. Various techniques such as scanning electron microscopy, Rutherford backscattering spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and Raman spectroscopy have been used to characterize the morphology and the composition of the nanospheres. Experimental parameters may be adjusted to favour the formation of bismuth nanospheres instead of microspheres. Therefore, the formation of large surface of homogeneous layer of bismuth nanospheres with sizes of below 100 nm can be obtained. The natural snowball phenomenon is observed to be reproduced in nanoscale where spheres roll over the small nanospheres and grow up to bigger sizes that can reach micro dimensions. The comet-like structure, a reverse phenomenon to snowball is also observed

  16. Mixed-phase bismuth ferrite nanoflake electrodes for supercapacitor application

    Science.gov (United States)

    Jadhav, Vijaykumar V.; Zate, Manohar K.; Liu, Shude; Naushad, Mu.; Mane, Rajaram S.; Hui, K. N.; Han, Sung-Hwan

    2016-04-01

    Nanoflake bismuth ferrite thin film was synthesized by means of electrodeposition technique at room temperature. The morphology and phase evaluation of the synthesized electrode were analyzed using scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and surface wettability techniques. Specifically, the bismuth ferrite nanoflake electrode exhibited high specific capacitance of 72.2 F g-1 at a current density of 1 A g-1, and high rate capability with 37 % retention of capacitance even up to 20A g-1, and excellent cycling stability with 82.8 % retention of the initial capacitance after 1500 charge/discharge cycles, supporting that the bismuth ferrite thin-film electrode could be a potential candidate for supercapacitor application.

  17. Thermal, structural and electrical studies of bismuth zinc borate glasses

    Science.gov (United States)

    Shanmugavelu, B.; Ravi Kanth Kumar, V. V.

    2013-06-01

    Bismuth Zinc Borate glasses with compositions xBi2O3-30ZnO-(70 - x)B2O3 (where x = 30, 35, 40 and 45 mol %) have been prepared by melt quenching method. These glasses were characterized by X-ray diffraction (XRD), Differential Thermal Analysis (DTA), Fourier Transform Infrared Spectrometer (FTIR) and Broad Band Dielectric Spectrometer (BDS). DTA and FTIR analysis reveals that Non-Bridging Oxygens (NBOs) increase with increase of bismuth content in the glass. Electrical data have been analyzed in the framework of impedance and modulus formalisms. The activation energy for dc conductivity decreases with increase of bismuth concentration. The imaginary part of modulus spectra has been fitted to non-exponential Kohlrausch-Williams-Watts (KWW) function and the value of the stretched exponent (β) is found to be almost independent of temperature but slightly dependent on composition.

  18. Characterization of bismuth nanospheres deposited by plasma focus device

    Energy Technology Data Exchange (ETDEWEB)

    Ahmad, M., E-mail: cscientific2@aec.org.sy [IBA Laboratory, Chemistry Department, Atomic Energy Commission of Syria, P.O. Box 6091, Damascus (Syrian Arab Republic); Al-Hawat, Sh.; Akel, M. [Physics Department, Atomic Energy Commission of Syria, P.O. Box 6091, Damascus (Syrian Arab Republic); Mrad, O. [Chemistry Department, Atomic Energy Commission of Syria, P.O. Box 6091, Damascus (Syrian Arab Republic)

    2015-02-14

    A new method for producing thin layer of bismuth nanospheres based on the use of low energy plasma focus device is demonstrated. Various techniques such as scanning electron microscopy, Rutherford backscattering spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and Raman spectroscopy have been used to characterize the morphology and the composition of the nanospheres. Experimental parameters may be adjusted to favour the formation of bismuth nanospheres instead of microspheres. Therefore, the formation of large surface of homogeneous layer of bismuth nanospheres with sizes of below 100 nm can be obtained. The natural snowball phenomenon is observed to be reproduced in nanoscale where spheres roll over the small nanospheres and grow up to bigger sizes that can reach micro dimensions. The comet-like structure, a reverse phenomenon to snowball is also observed.

  19. Participation Behaviour of East German Women After German Unification

    OpenAIRE

    Bonin, Holger; Euwals, Rob

    2002-01-01

    The Paper studies the determinants of labour force participation by East German women after unification. To isolate the role of preferences on labour force participation from individual characteristics, we develop a panel data model that simultaneously explains participation, employment and wages. The model, estimated for East and West Germany on the basis of the German Socio-Economic Panel, indicates that distinct preferences could explain the regional difference in participation rates at un...

  20. Compact and Integrated Liquid Bismuth Propellant Feed System

    Science.gov (United States)

    Polzin, Kurt A.; Stanojev, Boris; Korman, Valentin; Gross, Jeffrey T.

    2007-01-01

    Operation of Hall thrusters with bismuth propellant has been shown to be a promising path toward high-power, high-performance, long-lifetime electric propulsion for spaceflight missions [1]. There has been considerable effort in the past three years aimed at resuscitating this promising technology and validating earlier experimental results indicating the advantages of a bismuth-fed Hall thruster. A critical element of the present effort is the precise metering of propellant to the thruster, since performance cannot be accurately assessed without an accurate accounting of mass flow rate. Earlier work used a pre./post-test propellant weighing scheme that did not provide any real-time measurement of mass flow rate while the thruster was firing, and makes subsequent performance calculations difficult. The motivation of the present work is to develop a precision liquid bismuth Propellant Management System (PMS) that provides hot, molten bismuth to the thruster while simultaneously monitoring in real-time the propellant mass flow rate. The system is a derivative of our previous propellant feed system [2], but the present system represents a more compact design. In addition, all control electronics are integrated into a single unit and designed to reside on a thrust stand and operate in the relevant vacuum environment where the thruster is operating, significantly increasing the present technology readiness level of liquid metal propellant feed systems. The design of various critical components in a bismuth PMS are described. These include the bismuth reservoir and pressurization system, 'hotspot' flow sensor, power system and integrated control system. Particular emphasis is given to selection of the electronics employed in this system and the methods that were used to isolate the power and control systems from the high-temperature portions of the feed system and thruster. Open loop calibration test results from the 'hotspot' flow sensor are reported, and results of

  1. Tin-silver-bismuth solders for electronics assembly

    Science.gov (United States)

    Vianco, Paul T.; Rejent, Jerome A.

    1995-01-01

    A lead-free solder alloy for electronic assemblies composed of a eutectic alloy of tin and silver with a bismuth addition, x, of 0tin effective to depress the melting point of the tin-silver composition to a desired level. Melting point ranges from about 218.degree. C. down to about 205.degree. C. depending an the amount of bismuth added to the eutectic tin-silver alloy as determined by DSC analysis, 10.degree. C./min. A preferred alloy composition is 91.84Sn-3.33Ag-4.83Bi (weight percent based on total alloy weight).

  2. High-Q bismuth silicate nonlinear glass microsphere resonators

    OpenAIRE

    Wang, Pengfei; Murugan, Ganapathy; Lee, Timothy; Ding, Ming; Brambilla, Gilberto; Semenova, Yuliya; Wu, Qiang; Koizumi,Fumihito; Farrell, Gerald

    2012-01-01

    The fabrication and characterization of a bismuth-silicate glass microsphere resonator has been demonstrated. At wavelengths near 1550 nm, high-modes can be efficiently excited in a 179-μm diameter bismuth-silicate glass microsphere via evanescent coupling using a tapered silica fiber with a waist diameter of circa 2 μm. Resonances with Q-factors as high as were observed. The dependence of the spectral response on variations in the input power level was studied in detail to gain an insight in...

  3. Lead–bismuth eutectic technology for Hyperion reactor

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, J., E-mail: Zhang.3558@osu.edu [Dept. of Mechanical and Aerospace Engineering, The Ohio State University, 201 W, 19th Avenue, Columbus, OH 43210 (United States); Nuclear Engineering and Nonproliferation Division, Los Alamos National Laboratory, Los Alamos, NM 87544 (United States); Kapernick, R.J.; McClure, P.R. [Nuclear Engineering and Nonproliferation Division, Los Alamos National Laboratory, Los Alamos, NM 87544 (United States); Trapp, T.J. [Hyperion Power Generation (United States)

    2013-10-15

    A small lead–bismuth eutectic-cooled reactor concept (referred to as the Hyperion reactor concept) is being studied at Los Alamos National Laboratory and Hyperion Power Generation. In this report, a critical assessment of the lead–bismuth eutectic technology for Hyperion reactor is presented based on currently available knowledge. Included are: material compatibility, oxygen control, thermal hydraulics, polonium control. The key advances in the technology and their applications to Hyperion reactor design are analyzed. Also, the near future studies in main areas of the technology are recommended for meeting the design requirements.

  4. Bismuth onion thin film in situ grown on silicon wafer synthesized through a hydrothermal approach

    International Nuclear Information System (INIS)

    Bismuth onion structured nanospheres with the same structure as carbon onions have been synthesized and observed. The nanospheres were synthesized through a hydrothermal method using bismuth hydroxide and silicon wafer as reactants. By controlling the heating temperature, heating time, and the pressure, nanoscale bismuth spheres can be in situ synthesized on silicon wafer, and forms a bismuth onion film on the substrate. The electronic property of the films was investigated. A formation mechanism of the formation of bismuth onions and the onion film has been proposed on the basis of experimental observations.

  5. Bismuth centred magnetic perovskite: A projected multiferroic

    International Nuclear Information System (INIS)

    In recent time substantial attention has been initiated to understand the physics behind multiferroism and to design new multiferroic materials. BiMnO3 and BiFeO3 are the well-studied Bi-centred multiferroic oxides. BiMnO3 is a ferromagnetic–ferroelectric (metastable) phase and require drastic conditions to synthesize. However, lanthanum substituted BiMnO3 phases stabilized at ambient pressure. It is thus of major importance to increase the number of ferromagnetic perovskites with Bi cations that could be designed under ambient conditions. In this article, we have presented an up to date report of investigations on Bi-centred magnetic perovskites, a prospective material for multiferroic application. Central focus is concentrated on La0.5Bi0.5MnO3 perovskite with various substitutions at different levels. A few of these perovskites are found to be of practical importance e.g. La0.5Bi0.5Mn0.67Co0.33O3 with high dielectric permittivity coupled with ferromagnetism. A comprehensive analysis of different physical functionalities and their interrelation for a wide range of compositions of these Bi-centred perovskites is presented. It has been found that the complex magnetic behaviour originates from mixed valence metal ions. The ferroelectricity is associated with the 6s2 lone pair of Bi3+ cations. The magnetic ground state influences the dielectric properties reflecting the multiferroism in a single material. - Highlights: • Multiferroics have attracted increasing attention due to their possible device applications. • Bismuth centred magnetic perovskite is one kind of such promising multiferroic materials. • Ferromagnetic Bi-perovskites, which are synthesized at ambient conditions, have been discussed

  6. A new German law

    International Nuclear Information System (INIS)

    A new law about the production of electricity came into effect last april in Germany. A renewable energy expert presents this law and its consequences to the electricity market. The previous EFL (electricity feed-in law, 1991) has greatly contributed to the development of wind energy during the last decade but a new law was necessary to comply with European regulations about free electricity market and with European Commission 's aim of doubling the contribution of renewable energies to the European energy balance by 2010. This law sets the purchase prices of electricity by delivery companies according to the renewable energy (wind, photovoltaic,biomass, biogas, mine gas and geothermal) and a compensation system has been thoroughly elaborated. At the end the customer will have to pay the bill but the price is reasonable, the extra-cost is expected to be somewhere between 35 and 70 French francs a year for each electricity consumer but with the perspective of a doubling of the contribution of renewable energies to the German electricity market between 1995 and 2010. (A.C.)

  7. Mark Twain and "The Awful German Language."

    Science.gov (United States)

    Hedderich, Norbert

    2003-01-01

    Analyzes Mark Twain's 1869 essay "The Awful German Language" in terms of Twain's comments on morphological, syntactical, lexical, and phonological features of German. The topic is presented in the context of Twain's German language learning experience. Relevance of the article for German language instruction today is also described. (Author/VWL)

  8. German labour markets after unification

    OpenAIRE

    Franz, Wolfgang

    1991-01-01

    This paper contains a description and analysis of the labour market in East Germany and an econometric evaluation of some effects of German unification on the West German labour market. At the outset, recent developments of employment and unemployment in East Germany are summarized together with an attempt at evaluation of the sources of joblessness. Moreover,'wage determination and wage dynamics are discussed at some length. It is investigated to what extent wage theories can contribute to a...

  9. Immobile Complex Verbs in Germanic

    DEFF Research Database (Denmark)

    Vikner, Sten

    Certain complex verbs in Dutch, German, and Swiss German do not undergo verb movement. The suggestion to be made in this article is that these ‘‘immobile'' verbs have to fulfill both the requirements imposed on complex verbs of the V° type (=verbs with non-separable prefixes) and the requirements...... immobile, - why such verbs are not found in Germanic VO-languages such as English and Scandinavian.......Certain complex verbs in Dutch, German, and Swiss German do not undergo verb movement. The suggestion to be made in this article is that these ‘‘immobile'' verbs have to fulfill both the requirements imposed on complex verbs of the V° type (=verbs with non-separable prefixes) and the requirements...... the V° requirements or the V* requirements. Haider (1993, p. 62) and Koopman (1995), who also discuss such immobile verbs, only account for verbs with two prefix-like parts (e.g., German uraufführen ‘to perform (a play) for the first time' or Dutch herinvoeren ‘to reintroduce'), not for the more...

  10. German status report

    International Nuclear Information System (INIS)

    Since there will be operating NPPs in Germany for about 20 years, it is necessary to preserve the appropriate competence in industry as well as with the authorities and the TSOs. Because of early retirement programmes of the utilities and minor reductions of manpower in the NPPs, there is a potential risk of degradations of the existing level of technical qualification within the NPPs. A fast replacement of the retired NPP staff by young engineers, technicians or craftsmen, can create a common problem. There are some small hints, that a relative fast replacement of staff in some utilities has contributed to unexpected events during the last 2 years in German NPPs. Therefore it is necessary to observe carefully developments and trends in plant performance also in the future. The regulatory bodies have started some initiatives to observe more closely manning and technical qualification situation in the German NPPs as in the past. The situation looks even more difficult for the authorities and in particular the TSOs as young engineers are not willing to work in the nuclear field due to the perspectives. Nevertheless, substitutions of retiring staff are meanwhile necessary after a long period of personnel reduction. As the peak in the age structure of the employees is at an age of nearly 60 years, it is a very urgent matter to care for the preservation of competence. The problem has been realized and first steps are going to be taken, e.g. loss of competence analysis, organization of training courses and updating of existing training material, elaboration of a training concept for initial training. The deregulation in the energy market has led to efforts for cost reduction by the utilities. One of the possibilities for cost reduction which was taken into account was the reduction of costs for the NPP personnel. In this context 3 ways were considered: reduction of the absolute staff figure; substitution of old staff members by young ones; outsourcing. The responsible

  11. Bismuth Ferrite for Active Control of Surface Plasmon Polariton Modes

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia; Zhukovsky, Sergei; Lavrinenko, Andrei

    We propose and investigate several layouts of m etal-insulator-metal waveguide with active core which can be utilized for dynamic switching in photonic integrated circuits. The active material, bismuth ferrite (BiFeO3), is sandwiched between metal plates and changes i ts refractive index through ...

  12. Ultrafast electron diffraction studies of optically excited thin bismuth films

    International Nuclear Information System (INIS)

    This thesis contains work on the design and the realization of an experimental setup capable of providing sub-picosecond electron pulses for ultrafast electron diffraction experiments, and performing the study of ultrafast dynamics in bismuth after optical excitation using this setup. (orig.)

  13. Polymeric architectures of bismuth citrate based on dimeric building blocks

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Four bismuth complexes, (H2En)[Bi2(cit)2(H2O)4/3]·(H2O)x (1), (H2En)3[Bi2(cit)2Cl4]·(H2O)x (2), (HPy)2[Bi2(cit)2(H2O)8/5]·(H2O)x (3) and (H2En)[Bi2(cit)2](H2O)x (4) [cit = citrate4-; En = ethylenediamine; Py = pyridine] have been synthesized and crystallized. The crystal structures reveal that the basic building blocks in all of these complexes are bismuth citrate dimeric units which combine to form polymeric architectures. The embedded protonated ethylenediamine and pyridine moieties in the polymeric frameworks have been identified by X-ray crystallography and solid-state cross polarization/magic angle spinning (CP/MAS) 13C NMR. Based on the framework of complex 1, a structural model of a clinically used antiulcer drug, ranitidine bismuth citrate (RBC) was generated. The behavior of the protonated amine-bismuth citrate complexes in acidic aqueous solution has been studied by electrospray ionization-mass spectrometry (ESI-MS).

  14. Bismuth Ferrite for Active Control of Surface Plasmon Polariton Modes

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia; Zhukovsky, Sergei; Lavrinenko, Andrei

    2014-01-01

    We propose and investigate several layouts of m etal-insulator-metal waveguide with active core which can be utilized for dynamic switching in photonic integrated circuits. The active material, bismuth ferrite (BiFeO3), is sandwiched between metal plates and changes i ts refractive index through...

  15. Synthesis and structural characterization of Ce-doped bismuth titanate

    International Nuclear Information System (INIS)

    Ce-modified bismuth titanate nanopowders Bi4-xCexTi3O12 (x ≤ 1) have been synthesized using a coprecipitation method. DTA/TG, FTIR, XRD, SEM/EDS and BET methods were used in order to investigate the effect of Ce-substitution on the structure, morphology and sinterability of the obtained powders. The phase structure investigation revealed that after calcinations at 600 deg. C powder without Ce addition exhibited pure bismuth titanate phase; however, powders with Ce (x = 0.25, 0.5 and 0.75) had bismuth titanate pyrochlore phase as the second phase. The strongest effect of Ce addition on the structure was noted for the powder with the highest amount of Ce (x = 1) having a cubic pyrochlore structure. The presence of pure pyrochlore phase was explained by its stabilization due to the incorporation of cerium ions in titanate structure. Ce-modified bismuth titanate ceramic had a density over 95% of theoretical density and the fracture in transgranular manner most probably due to preferable distribution of Ce in boundary region

  16. Measured and evaluated neutron cross sections of elemental bismuth

    International Nuclear Information System (INIS)

    Neutron total cross sections of elemental bismuth are measured with broad resolution from 1.2 to 4.5 MeV to accuracies of approx. = 1%. Neutron-differential-elastic-scattering cross sections of bismuth are measured from 1.5 to 4.0 MeV at incident neutron energy intervals of approx.< 0.2 MeV over the scattered-neutron angular range approx. = 20 to 160 deg. Differential neutron cross sections for the excitation of observed states in bismuth at 895 +- 12, 1606 +- 14, 2590 +- 15, 2762 +- 29, 3022 +- 21, and 3144 +- 15 keV are determined at incident neutron energies up to 4.0 MeV. An optical-statistical model is deduced from the measured values. This model, the present experimental results, and information available elsewhere in the literature are used to construct a comprehensive evaluated nuclear data file for elemental bismuth in the ENDF format. The evaluated file is particularly suited to the neutronic needs of the fusion-fission hybrid designer. 87 references, 10 figures, 6 tables

  17. Ultrafast electronic dynamics in laser-excited crystalline bismuth

    Directory of Open Access Journals (Sweden)

    Chekalin S.

    2013-03-01

    Full Text Available Femtosecond spectroscopy was applied to capture complex dynamics of non equilibrium electrons in bismuth. Data analysis reveals significant wavevector dependence of electron-hole and electron-phonon coupling strength along the Γ-T direction of the Brillouin zone

  18. Ultrafast electron diffraction studies of optically excited thin bismuth films

    Energy Technology Data Exchange (ETDEWEB)

    Rajkovic, Ivan

    2008-10-21

    This thesis contains work on the design and the realization of an experimental setup capable of providing sub-picosecond electron pulses for ultrafast electron diffraction experiments, and performing the study of ultrafast dynamics in bismuth after optical excitation using this setup. (orig.)

  19. Phase transition of bismuth telluride thin films grown by MBE

    DEFF Research Database (Denmark)

    Fülöp, Attila; Song, Yuxin; Charpentier, Sophie;

    2014-01-01

    A previously unreported phase transition between Bi2Te3 and Bi4Te3 in bismuth telluride grown by molecular beam epitaxy is recorded via XRD, AFM, and SIMS observations. This transition is found to be related to the Te/Bi beam equivalent pressure (BEP) ratio. BEP ratios below 17 favor the formatio...

  20. Surface depletion in the vacuum distillation of metals from bismuth

    International Nuclear Information System (INIS)

    Surface depletion was investigated in laboratory- and plant-scale distillation units with mixing by natural convection or by mechanical surface agitation. A model was developed for predicting the degree of surface depletion during the distillation of metals from bismuth as a function of temperature, still pot dimensions, and degree of agitation. This paper discusses those findings

  1. Discovery of the thallium, lead, bismuth, and polonium isotopes

    OpenAIRE

    Fry, C; Thoennessen, M

    2012-01-01

    Currently, forty-two thallium, forty-two lead, forty-one bismuth, and forty-two polonium isotopes have so far been observed; the discovery of these isotopes is discussed. For each isotope a brief summary of the first refereed publication, including the production and identification method, is presented.

  2. Third order nonlinear optical properties of bismuth zinc borate glasses

    International Nuclear Information System (INIS)

    Third order nonlinear optical characterization of bismuth zinc borate glasses are reported here using different laser pulse durations. Bismuth zinc borate glasses with compositions xBi2O3-30ZnO-(70-x) B2O3 (where x = 30, 35, 40, and 45 mol. %) have been prepared by melt quenching method. These glasses were characterized by Raman, UV-Vis absorption, and Z scan measurements. Raman and UV-Vis spectroscopic results indicate that non-bridging oxygens increase with increase of bismuth content in the glass. Nonlinear absorption and refraction behavior in the nanosecond (ns), picosecond (ps), and femtosecond (fs) time domains were studied in detail. Strong reverse saturable absorption due to dominant two-photon absorption (TPA) was observed with both ps and fs excitations. In the case of ns pulse excitations, TPA and free-carrier absorption processes contribute for the nonlinear absorption. Two-photon absorption coefficient (β) and the absorption cross section due to free carriers (σe) are estimated by theoretical fit of the open aperture Z-scan measurements and found to be dependent on the amount of bismuth oxide in the glass composition. In both ns and fs regimes the sign and magnitude of the third order nonlinearity are evaluated, and the optical limiting characteristics are also reported

  3. Third order nonlinear optical properties of bismuth zinc borate glasses

    Science.gov (United States)

    Shanmugavelu, B.; Ravi Kanth Kumar, V. V.; Kuladeep, R.; Narayana Rao, D.

    2013-12-01

    Third order nonlinear optical characterization of bismuth zinc borate glasses are reported here using different laser pulse durations. Bismuth zinc borate glasses with compositions xBi2O3-30ZnO-(70-x) B2O3 (where x = 30, 35, 40, and 45 mol. %) have been prepared by melt quenching method. These glasses were characterized by Raman, UV-Vis absorption, and Z scan measurements. Raman and UV-Vis spectroscopic results indicate that non-bridging oxygens increase with increase of bismuth content in the glass. Nonlinear absorption and refraction behavior in the nanosecond (ns), picosecond (ps), and femtosecond (fs) time domains were studied in detail. Strong reverse saturable absorption due to dominant two-photon absorption (TPA) was observed with both ps and fs excitations. In the case of ns pulse excitations, TPA and free-carrier absorption processes contribute for the nonlinear absorption. Two-photon absorption coefficient (β) and the absorption cross section due to free carriers (σe) are estimated by theoretical fit of the open aperture Z-scan measurements and found to be dependent on the amount of bismuth oxide in the glass composition. In both ns and fs regimes the sign and magnitude of the third order nonlinearity are evaluated, and the optical limiting characteristics are also reported.

  4. Third order nonlinear optical properties of bismuth zinc borate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Shanmugavelu, B.; Ravi Kanth Kumar, V. V., E-mail: ravi.phy@pondiuni.edu.in [Department of Physics, Pondicherry University, Puducherry 605 014 (India); Kuladeep, R.; Narayana Rao, D. [School of Physics, University of Hyderabad, Hyderabad 500046, Andhra Pradesh (India)

    2013-12-28

    Third order nonlinear optical characterization of bismuth zinc borate glasses are reported here using different laser pulse durations. Bismuth zinc borate glasses with compositions xBi{sub 2}O{sub 3}-30ZnO-(70-x) B{sub 2}O{sub 3} (where x = 30, 35, 40, and 45 mol. %) have been prepared by melt quenching method. These glasses were characterized by Raman, UV-Vis absorption, and Z scan measurements. Raman and UV-Vis spectroscopic results indicate that non-bridging oxygens increase with increase of bismuth content in the glass. Nonlinear absorption and refraction behavior in the nanosecond (ns), picosecond (ps), and femtosecond (fs) time domains were studied in detail. Strong reverse saturable absorption due to dominant two-photon absorption (TPA) was observed with both ps and fs excitations. In the case of ns pulse excitations, TPA and free-carrier absorption processes contribute for the nonlinear absorption. Two-photon absorption coefficient (β) and the absorption cross section due to free carriers (σ{sub e}) are estimated by theoretical fit of the open aperture Z-scan measurements and found to be dependent on the amount of bismuth oxide in the glass composition. In both ns and fs regimes the sign and magnitude of the third order nonlinearity are evaluated, and the optical limiting characteristics are also reported.

  5. New German abortion law agreed.

    Science.gov (United States)

    Karcher, H L

    1995-07-15

    The German Bundestag has passed a compromise abortion law that makes an abortion performed within the first three months of pregnancy an unlawful but unpunishable act if the woman has sought independent counseling first. Article 218 of the German penal code, which was established in 1871 under Otto von Bismarck, had allowed abortions for certain medical or ethical reasons. After the end of the first world war, the Social Democrats tried to legalize all abortions performed in the first three months of pregnancy, but failed. In 1974, abortion on demand during the first 12 weeks was declared legal and unpunishable under the social liberal coalition government of chancellor Willy Brandt; however, the same year, the German Federal Constitution Court in Karlsruhe ruled the bill was incompatible with article 2 of the constitution, which guarantees the right to life and freedom from bodily harm to everyone, including the unborn. The highest German court also ruled that a pregnant woman had to seek a second opinion from an independent doctor before undergoing an abortion. A new, extended article 218, which included a clause giving social indications, was passed by the Bundestag. When Germany was unified, East Germans agreed to be governed by all West German laws, except article 218. The Bundestag was given 2 years to revise the article; however, in 1993, the Federal Constitution Court rejected a version legalizing abortion in the first 3 months of the pregnancy if the woman sought counsel from an independent physician, and suggested the recent compromise passed by the Bundestag, the lower house of the German parliament. The upper house, the Bundesrat, where the Social Democrats are in the majority, still has to pass it. Under the bill passed by the Bundestag, national health insurance will pay for an abortion if the monthly income of the woman seeking the abortion falls under a certain limit. PMID:7613423

  6. Bismuth-based oxide semiconductors: Mild synthesis and practical applications

    Science.gov (United States)

    Timmaji, Hari Krishna

    In this dissertation study, bismuth based oxide semiconductors were prepared using 'mild' synthesis techniques---electrodeposition and solution combustion synthesis. Potential environmental remediation and solar energy applications of the prepared oxides were evaluated. Bismuth vanadate (BiVO4) was prepared by electrodeposition and solution combustion synthesis. A two step electrosynthesis strategy was developed and demonstrated for the first time. In the first step, a Bi film was first electrodeposited on a Pt substrate from an acidic BiCl3 medium. Then, this film was anodically stripped in a medium containing hydrolyzed vanadium precursor, to generate Bi3+, and subsequent BiVO4 formation by in situ precipitation. The photoelectrochemical data were consistent with the in situ formation of n-type semiconductor films. In the solution combustion synthesis procedure, BiVO4 powders were prepared using bismuth nitrate pentahydrate as the bismuth precursor and either vanadium chloride or vanadium oxysulfate as the vanadium precursor. Urea, glycine, or citric acid was used as the fuel. The effect of the vanadium precursor on the photocatalytic activity of combustion synthesized BiVO 4 was evaluated in this study. Methyl orange was used as a probe to test the photocatalytic attributes of the combustion synthesized (CS) samples, and benchmarked against a commercial bismuth vanadate sample. The CS samples showed superior activity to the commercial benchmark sample, and samples derived from vanadium chloride were superior to vanadium oxysulfate counterparts. The photoelectrochemical properties of the various CS samples were also studied and these samples were shown to be useful both for environmental photocatalytic remediation and water photooxidation applications. Silver bismuth tungstate (AgBiW2O8) nanoparticles were prepared for the first time by solution combustion synthesis by using silver nitrate, bismuth nitrate, sodium tungstate as precursors for Ag, Bi, and W

  7. German cancer statistics 2004

    Directory of Open Access Journals (Sweden)

    Ziese Thomas

    2010-02-01

    Full Text Available Abstract Background For years the Robert Koch Institute (RKI has been annually pooling and reviewing the data from the German population-based cancer registries and evaluating them together with the cause-of-death statistics provided by the statistical offices. Traditionally, the RKI periodically estimates the number of new cancer cases in Germany on the basis of the available data from the regional cancer registries in which registration is complete; this figure, in turn, forms the basis for further important indicators. Methods This article gives a brief overview of current indicators - such as incidence, prevalence, mortality, survival rates - on the most common types of cancer, as well as important ratios on the risks of developing and dying of cancer in Germany. Results According to the latest estimate, there were a total of 436,500 new cancer cases in Germany in 2004. The most common cancer in men is prostate cancer with over 58,000 new cases per annum, followed by colorectal and lung cancer. In women, breast cancer remains the most common cancer with an estimated 57,000 new cases every year, also followed by colorectal cancer. These and further findings on selected cancer sites can be found in the current brochure on "Cancer in Germany", which is regularly published by the RKI together with the Association of Population-based Cancer Registries in Germany (GEKID. In addition, the RKI made cancer-prevalence estimates and calculated current morbidity and mortality risks at the federal level for the first time. According to these figures, the 5-year partial prevalence - i.e. the total number of cancer patients diagnosed over the past five years who are currently still living - exceeds 600,000 in men; the figure is about the same among women. Here, too, the most common cancers are prostate cancer in men and breast cancer in women. The lifetime risk of developing cancer, which is more related to the individual, is estimated to be higher among

  8. Dividend Policy of German Firms

    OpenAIRE

    M. Goergen; Renneboog, L.D.R.; Correia Da Silva, L.

    2004-01-01

    German firms pay out a lower proportion of their cash flows than UK and US firms.However, on a published profits basis, the pattern is reversed.Company law provisions and accounting policies account for these conflicting results.A partial adjustment model is used to estimate the implicit target payout ratio and the speed of adjustment of dividends towards a long run target payout ratio. We find that German firms do not base their dividend decisions on published earnings, but on cash flows.The...

  9. The Danish Press during the German Occupation

    DEFF Research Database (Denmark)

    Roslyng-Jensen, Palle

    2010-01-01

    Censorship, self-censorship in Danish newspapers and Danish Radio during the German occupation of Denmark 1940-45......Censorship, self-censorship in Danish newspapers and Danish Radio during the German occupation of Denmark 1940-45...

  10. Hyperfine Clock Transitions of Bismuth Donors in Silicon Detected by Spin Dependent Recombination

    OpenAIRE

    Mortemousque, Pierre-André; Berger, Simon; Sekiguchi, Takeharu; Culan, Christophe; Elliman, Robert G.; Kohei M. Itoh

    2014-01-01

    Bismuth donors ion-implanted in $^{28}$Si and $^\\text{nat}$Si are studied using magnetic resonance spectroscopy based on spin dependent recombination. The hyperfine clock transition, at which the linewidth is significantly narrowed, is observed for the bismuth donors. The experimental results are modeled quantitatively by molecular orbital theory for a coupled pair consisting of a bismuth donor and a spin dependent recombination readout center, including the effect of hyperfine and Zeeman int...

  11. Bismuth nitrate-induced microwave-assisted expeditious synthesis of vanillin from curcumin

    OpenAIRE

    Bandyopadhyay, Debasish; Banik, Bimal K

    2012-01-01

    Background Curcumin and vanillin are the two useful compounds in food and medicine. Bismuth nitrate pentahydrate is an economical and ecofriendly reagent. Method Bismuth nitrate pentahydrate impregnated montmorillonite KSF clay and curcumin were subjected to microwave irradiation. Results Microwave-induced bismuth nitrate-promoted synthesis of vanillin from curcumin has been accomplished in good yield under solvent-free condition. Twenty-five different reaction conditions have been studied to...

  12. Rapid semi-quantitative determination of bismuth in minerals using ascending paper chromatography (1961)

    International Nuclear Information System (INIS)

    The bismuth is separated by a solvent made up of acetone, water, and hydrofluoric and hydrochloric acids. The bismuth is developed with dimercapto-2.5 thio-diazole-1.3.4 and ammonium sulphide. The use of this method for the detection of bismuth in minerals makes it possible to determine the metal at a concentration of 5 x 10-6. (author)

  13. Standard triple, bismuth pectin quadruple and sequential therapies for Helicobacter pylori eradication

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    AIM: To compare the effectiveness of standard triple, bismuth pectin quadruple and sequential therapies for Helicobacter pylori (H. pylori ) eradication in a randomized, double-blinded, comparative clinical trial in China. METHODS: A total of 215 H. pylori -positive patients were enrolled in the study and randomly allocated into three groups: group A (n = 72) received a 10-d bismuth pectin quadruple therapy (20 mg rabeprazole bid , 1000 mg amoxicillin bid , 100 mg bismuth pectin qid , and 500 mg levofloxaci...

  14. Dividend Policy of German Firms

    NARCIS (Netherlands)

    Goergen, M.; Renneboog, L.D.R.; Correia Da Silva, L.

    2004-01-01

    German firms pay out a lower proportion of their cash flows than UK and US firms.However, on a published profits basis, the pattern is reversed.Company law provisions and accounting policies account for these conflicting results.A partial adjustment model is used to estimate the implicit target payo

  15. Influence of bismuth on structural, elastic and spectroscopic properties of Nd{sup 3+} doped Zinc–Boro-Bismuthate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, Gaurav; Sontakke, Atul D.; Karmakar, P.; Biswas, K.; Balaji, S.; Saha, R.; Sen, R.; Annapurna, K., E-mail: annapurnak@cgcri.res.in

    2014-05-01

    The present investigation reports, influence of bismuth addition on structural, elastic and spectral properties of [(99.5−x) {4ZnO−3B_2O_3}−0.5Nd{sub 2}O{sub 3}−x Bi{sub 2}O{sub 3} where x=0, 5, 10, 20, 30, 40, 50 and 60] glasses. The measured FTIR reflectance spectra facilitated a thorough insight of methodical modifications that are arising in the glass structure from borate (build by BO{sub 3} and BO{sub 4} units) to bismuthate (BiO{sub 3} and BiO{sub 6} units) network due to the increase of bismuth content ensuing with a steady decrease in host phonon energy (ν{sub ph}). The elastic properties estimated from measured longitudinal and shear ultrasonic velocities (U{sub L} and U{sub s}) demonstrated the reduction in network rigidity of glasses on Bi{sub 2}O{sub 3} inclusion. The three phenomenological Judd–Ofelt intensity parameters (Ω{sub 2,4,6}) were obtained from recorded absorption spectra of Nd{sup 3+} ions in these glasses and have been used to predict radiative properties as a function of variation in bismuth content. The reduced host phonon energy and high optical basicity effect due to Bi{sub 2}O{sub 3} incorporation remarkably improved the Nd{sup 3+} luminescence properties such as emission intensity, quantum yield and emission cross-section. The quantum yield showed a strong increase from mere 16% in Zinc–Borate glass to almost 73% in 60 mol% Bi{sub 2}O{sub 3} containing glass. Similarly, the emission cross-section for Nd{sup 3+4}F{sub 3/2}→{sup 4}I{sub 11/2} laser transition raised from 2.43×10{sup −20} cm{sup 2} to 3.95×10{sup −20} cm{sup 2} in studied concentration suggesting a strong improvement in Nd{sup 3+} laser spectroscopic properties in Zinc–Boro-Bismuthate glass. These materials may be promising for compact solid state infrared lasers. - Highlights: • Continuous structural changes associated with reduction in host phonon energy by Bi{sub 2}O{sub 3} inclusion. • Ultrasonic velocity study revealed reduced Debye

  16. Influence of bismuth on structural, elastic and spectroscopic properties of Nd3+ doped Zinc–Boro-Bismuthate glasses

    International Nuclear Information System (INIS)

    The present investigation reports, influence of bismuth addition on structural, elastic and spectral properties of [(99.5−x) {4ZnO−3B2O3}−0.5Nd2O3−x Bi2O3 where x=0, 5, 10, 20, 30, 40, 50 and 60] glasses. The measured FTIR reflectance spectra facilitated a thorough insight of methodical modifications that are arising in the glass structure from borate (build by BO3 and BO4 units) to bismuthate (BiO3 and BiO6 units) network due to the increase of bismuth content ensuing with a steady decrease in host phonon energy (νph). The elastic properties estimated from measured longitudinal and shear ultrasonic velocities (UL and Us) demonstrated the reduction in network rigidity of glasses on Bi2O3 inclusion. The three phenomenological Judd–Ofelt intensity parameters (Ω2,4,6) were obtained from recorded absorption spectra of Nd3+ ions in these glasses and have been used to predict radiative properties as a function of variation in bismuth content. The reduced host phonon energy and high optical basicity effect due to Bi2O3 incorporation remarkably improved the Nd3+ luminescence properties such as emission intensity, quantum yield and emission cross-section. The quantum yield showed a strong increase from mere 16% in Zinc–Borate glass to almost 73% in 60 mol% Bi2O3 containing glass. Similarly, the emission cross-section for Nd3+4F3/2→4I11/2 laser transition raised from 2.43×10−20 cm2 to 3.95×10−20 cm2 in studied concentration suggesting a strong improvement in Nd3+ laser spectroscopic properties in Zinc–Boro-Bismuthate glass. These materials may be promising for compact solid state infrared lasers. - Highlights: • Continuous structural changes associated with reduction in host phonon energy by Bi2O3 inclusion. • Ultrasonic velocity study revealed reduced Debye temperature and elastic properties with bismuth addition. • Correlation of Judd–Ofelt parameters with structural modifications. • Realization of enhanced fluorescence quantum yield with

  17. Ab initio electronic structure and optical conductivity of bismuth tellurohalides

    CERN Document Server

    Schwalbe, Sebastian; Starke, Ronald; Schober, Giulio A H; Kortus, Jens

    2016-01-01

    We investigate the electronic structure, dielectric and optical properties of bismuth tellurohalides BiTeX (X = I, Cl, Br) by means of all-electron density functional theory. In particular, we present the ab initio conductivities and dielectric tensors calculated over a wide frequency range, and compare our results with the recent measurements by Akrap et al. , Makhnev et al. , and Rusinov et al. . We show how the low-frequency branch of the optical conductivity can be used to identify characteristic intra- and interband transitions between the Rashba spin-split bands in all three bismuth tellurohalides. We further calculate the refractive indices and dielectric constants, which in turn are systematically compared to previous predictions and measurements. We expect that our quantitative analysis will contribute to the general assessment of bulk Rashba materials for their potential use in spintronics devices.

  18. Chrysanthemum-like bismuth sulfide microcrystals: Synthesis, characterization, and properties

    Science.gov (United States)

    Jiang, Jinghui; Gao, Guanhua; Yu, Runnan; Qiu, Guanzhou; Liu, Xiaohe

    2011-02-01

    Uniform chrysanthemum-like bismuth sulfide (Bi 2S 3) microcrystals assembled from nanosheet building blocks were successfully synthesized via a convenient hydrothermal synthetic route under mild conditions in which hydrated bismuth nitrate and L-cysteine were employed to supply Bi and S source and ethylenediaminetetraacetic acid disodium salt (EDTA-Na 2) was employed as chelating agent. The influences of reaction temperatures and time on the morphologies of final products were investigated. The phase structures, morphologies, and properties of as-prepared products were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, high-resolution transmission electron microscope, and photoluminescence spectra. The possible growth mechanism for the formation of chrysanthemum-like Bi 2S 3 microcrystals was discussed on the basis of the experimental results.

  19. Quantum nernst effect in a bismuth single crystal

    International Nuclear Information System (INIS)

    We calculate the phonon-drag contribution to the transverse (Nernst) thermoelectric power Syx in a bismuth single crystal subjected to a quantizing magnetic field. The calculated heights of the Nernst peaks originating from the hole Landau levels and their temperature dependence reproduce the right order of magnitude for those of the pronounced magneto-oscillations recently reported by Behnia et al. A striking experimental finding that Syx is much larger than the longitudinal (Seebeck) thermoelectric power Sxx can be naturally explained as the effect of the phonon drag, combined with the well-known relation between the longitudinal and the Hall resistivity ρxx >> |ρyx| in a semi-metal bismuth. The calculation that includes the contribution of both holes and electrons suggests that some of the hitherto unexplained minor peaks located roughly at the fractional filling of the hole Landau levels are attributable to the electron Landau levels. (author)

  20. Thermophysical properties of liquid lead-bismuth eutectic

    International Nuclear Information System (INIS)

    Background: Liquid lead-bismuth eutectic (LBE) is important spallation target materials and candidate coolant materials in accelerator driven subcritical (ADS) system. Purpose: Its thermodynamic physical properties are keys to understand the basic problems in ADS R&D. Methods: By the calculation of scientific laws as well as fitting other scholars' experimental results, we tried to obtain the above thermodynamics physical properties. Results: By the calculation, we got formula about characteristic temperatures, density, specific heat, viscosity and thermal conductivity of liquid lead-bismuth alloy. And by fitting other scholars' experimental results, we got the fitting formula. Conclusions: Finally, by the contrast analysis, we found that the fitting formula and calculation formula agree well, and fitting formula more approaches the experimental value with a high accuracy whose differential deviation is not over 1%. (authors)

  1. Colloidal bismuth subcitrate in non-ulcer dyspepsia.

    Directory of Open Access Journals (Sweden)

    Khanna M

    1992-07-01

    Full Text Available The effect of colloidal bismuth subcitrate (De-Nol on symptoms, Helicobacter pylori status and histological features was studied in 35 patients with non-ulcer dyspepsia. Pain (34 cases and gas bloat (18 were the predominant symptoms. H pylori was present in 26 (74.3% patients. Gastritis and duodenitis were present in 29 of 32 and 22 of 31 cases respectively in whom biopsies were available. Relief in symptoms after treatment was seen in 29 (82.8% cases. Improvement in gastritis and duodenitis was noted in 60.8% and 58.8% respectively; over 70% of H pylori positive patients cleared the organism. These changes did not correlate with the relief in symptoms. We conclude that colloidal bismuth subcitrate is effective in the short term treatment of non-ulcer dyspepsia. It also clears H pylori infection and results in improvement of histological features.

  2. Effects of microwave sintering power on microstructure, dielectric, ferroelectric and magnetic properties of bismuth ferrite ceramics

    International Nuclear Information System (INIS)

    Highlights: ► Single-phase BFO ceramics have been prepared by microwave sintering. ► The lower sintering power is benefit for the decrease of its dielectric loss and leakage. ► Pr and Ec decrease with the increase of sintering power. ► Mr and Hc increase as sintering power increases. -- Abstract: Multiferroic bismuth ferrite ceramics were fabricated via microwave sintering. The microstructure, dielectric, ferroelectric and magnetic properties of bismuth ferrite ceramics sintered at different microwave powers are characterized by X-ray diffraction, scanning electron microscope, impedance analyzers, ferroelectric test system and vibrating sample magnetometer. Bismuth ferrite ceramics sintered at 3.4 kW is single phase and has dense structure and uniform grains. The lower microwave sintering power for bismuth ferrite ceramics is benefit for the decrease of its dielectric loss. The remnant polarization and coercive electric field of bismuth ferrite ceramics decrease with the increasing of microwave sintering power. The remnant polarization and the coercive electric field of bismuth ferrite ceramics decrease simultaneously as frequency increases. The leakage current of bismuth ferrite ceramics increases with the increase of microwave sintering power. Bismuth ferrite ceramics prepared by microwave sintering exhibit typical antiferromagnetic behaviors and the remnant magnetization and coercive magnetic field increase as the microwave sintering power increases. It is inferred that the optimum microwave sintering power for bismuth ferrite ceramics is 3.4 kW

  3. Optimal biliary drainage for inoperable Klatskin's tumor based on Bismuth type

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    AIM: To investigate differences in the effects of biliary drainage procedures in patients with inoperable Klatskin's tumor based on Bismuth type, considering endoscopic retrograde biliary drainage (ERBD), external percutaneous transhepatic biliary drainage (EPTBD) and internal biliary stenting via the PTBD tract (IPTBD).METHODS: The initial success rate, cumulative patency rate, and complication rate were compared retrospectively, according to the Bismuth type and ERBD,EPTBD, and IPTBD. Patency was defined as the duration for adequate initial bile drainage or to the point of the patient's death associated with inadequate drainage.RESULTS: One hundred thirty-four patients (93 men,41 women; 21 Bismuth type Ⅱ, 47 Ⅲ, 66 Ⅳ; 34 ERBD,66 EPTBD, 34 IPTBD) were recruited. There were no differences in demographics among the groups.Adequate initial relief of jaundice was achieved in 91% of patients without a significant difference in the results among different procedures or Bismuth types. The cumulative patency rates for ERBD and IPTBD were better than those for EPTBD with Bismuth type Ⅲ.IPTBD provided an excellent response for Bismuth type Ⅳ. However, there was no difference in the patency rate among drainage procedures for Bismuth type Ⅱ.Procedure-related cholangitis occurred less frequently with EPTBD than with ERBD and IPTBD.CONCLUSION: ERBD is recommended as the firstline drainage procedure for the palliation of jaundice in patients with inoperable Klatskin's tumor of Bismuth type Ⅱ or Ⅲ, but IPTBD is the best option for Bismuth type Ⅳ.

  4. Preparation of high-purity bismuth by sulphur deleadization in vacuum distillation

    Institute of Scientific and Technical Information of China (English)

    熊利芝; 何则强; 刘文萍; 麻成金; 戴永年

    2004-01-01

    The feasibility of separation of impurities in refined bismuth and sulphur deleadization with vacuum distillation was studied theoretically. Experimental studies on sulphur deleadization were carried out under vacuum.The influences of amount of sulphur, distillation temperature, vacuum degree and distillation time on deleadization were investigated and an optimal technical condition was achieved. The content of lead in refined bismuth can be decreased from 30 μg/g to 0.21 μg/g, which has reached the level of "5N" high-purity bismuth. Other impurities in refined bismuth can be also removed effectively under certain conditions.

  5. The Foreign Workers and Foreign Workers' German.

    Science.gov (United States)

    Blackshire-Belay, Carol

    Foreign Workers' German (FWG) refers to the acquired German language skills of workers from various countries who were recruited to West Germany between 1955 and 1973 to fill menial, undesirable jobs. Contact between these workers and native German speakers was limited because of the nature of the foreigners' work, the tendency toward residential…

  6. Layers of root nouns in Germanic

    DEFF Research Database (Denmark)

    Hansen, Bjarne Simmelkjær Sandgaard

    2015-01-01

    The root-noun declension became productive in early Germanic, containing (I) inherited root nouns, (IIa) original substrate or loan words, and transitions from other declensions in (IIb) Proto-Germanic and (III) North Germanic. As ablaut was abolished, the inherited type would display ablaut grades...

  7. Magnetic Properties of Bismuth Ferrite Nanopowder Obtained by Mechanochemical Synthesis

    OpenAIRE

    Szafraniak-Wiza, I.; Andrzejewski, B.; Hilczer, B.

    2014-01-01

    Multiferroic bismuth ferrite (BiFeO3) nanopowders have been obtained in room temperature by mechanical synthesis. Depending on the post-synthesis processing the nanopowders have exhibited differences in the mean sizes, presence of amorphous layer and/or secondary phases. Extended magnetic study performed for fresh, annealed and hot-pressed nanopowders have revealed substantial improvement of the magnetic properties in the as-prepared powder.

  8. Structural and electromechanical properties of bismuth-strontium titanate ceramics

    International Nuclear Information System (INIS)

    Bismuth-strontium titanate ceramics were obtained by conventional sinterization method (without orientation of grains - OF) and hot-forging (with oriented grains - HF). The physics, dielectrics and plutocracies properties these ceramics were compared. At piezoelectric characterization, the Kt values were higher in ceramics obtained by hot-forging (HF) when compared to ceramics obtained by OF, which indicates the high anisotropy of these materials. (author)

  9. Tunneling behavior of bismuth telluride nanoplates in electrical transport

    OpenAIRE

    Eginligil, Mustafa; Zhang, Weiqing; Kalitsov, Alan; Lu, Xianmao; Yang, Hyunsoo

    2012-01-01

    We study the electrical transport properties of ensembles of bismuth telluride (Bi2Te3) nanoplates grown by solution based chemical synthesis. Devices consisting of Bi2Te3 nanoplates are fabricated by surface treatment after dropping the solution on the structured gold plates and the temperature dependence of resistance shows a nonmetallic behavior. Symmetric tunneling behavior in I-V was observed in both our experimental results and theoretical calculation of surface conductance based on a s...

  10. Dose reduction using Bismuth protectors in chest computed tomography

    International Nuclear Information System (INIS)

    This monography is about the Dose reduction using Bismuth protectors in chest CT. The radiation protection of specific areas is necessary when the tissues or radiosensitive organs are near the path of light beam. The correct use of protection represents a challenge for the radiologist because of the time and materials required. The method used was a prospective investigatio in CHPR (TC service) and the doses was measured with TLD dosimeters. It is important to use these protectors in children hospitals.

  11. In vivo cellular uptake of bismuth ions from shotgun pellets

    OpenAIRE

    Stoltenberg, M; Locht, L.; Larsen, Agnete; Jensen, D.

    2003-01-01

    Shotgun pellets containing bismuth (Bi) are widely used and may cause a rather intense exposure of some wild animals to Bi. A Bi shotgun pellet was implanted intramuscularly in the triceps surae muscle of 18 adult male Wistar rats. Another group of 9 animals had a Bi shotgun pellet implanted intracranially in the neocortex. Eight weeks to 12 months later the release of Bi ions was analysed by autometallography (AMG) of tissue sections from different organs (bra...

  12. Lead-bismuth coolant cleaning from solid impurities using filtration

    International Nuclear Information System (INIS)

    The factors, influencing the efficiency of the circuit cleaning of the lead-bismuth coolant from the solid phase impurities through filtration, are analyzed. The choice of the filtration material is substantiated proceeding from the properties of the given coolant as a dispersion system. The results of the experiments on determining the efficiency of cleaning capacity by retained impurities, throughput and regeneration made it possible to develop the industrial filters for the NPU needs

  13. Weak antilocalization and UCFs in an open bismuth quantum dot

    Science.gov (United States)

    Hackens, B.; Minet, J. P.; Farhi, G.; Faniel, G.; Gustin, C.; Bayot, V.

    2003-04-01

    We report on the observation of weak antilocalization and universal conductance fluctuations in the magnetoconductance of an open quasi-ballistic bismuth nano-cavity. The electron decoherence length is comparable to sample dimensions at low temperature, while the spin-orbit coupling length is smaller. The temperature dependence of both the conductance and the dephasing length are consistent with two-dimensional electron-electron interactions being the dominant decoherence process.

  14. Proton irradiation on textured bismuth based cuprate superconductors

    International Nuclear Information System (INIS)

    Textured bulk polycrystalline samples of bismuth based cuprate superconductors have been subjected to irradiation with 15 MeV protons. In case of Bi-2212, there has been substantial increase in Tc, which may be due to proton induced knock-out of loosely bound oxygen. In case of (Bi,Pb)-2223, there has been a reduction in Tc. The difference in behaviour in these two systems towards proton irradiation has been explained. (author). 7 refs., 3 figs., 1 tab

  15. Shape-controlled solvothermal synthesis of bismuth subcarbonate nanomaterials

    International Nuclear Information System (INIS)

    Much effort has been devoted to the synthesis of novel nanostructured materials because of their unique properties and potential applications. Bismuth subcarbonate ((BiO)2CO3) is one of commonly used antibacterial agents against Helicobacter pylori (H. pylori). Different (BiO)2CO3 nanostructures such as cube-like nanoparticles, nanobars and nanoplates, were fabricated from bismuth nitrate via a simple solvothermal method. The nanostructures were characterized by powder X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). It was found that the solvents and precursors have an influence on the morphologies of (BiO)2CO3 nanostructures. The possible formation mechanism of different (BiO)2CO3 nanostructures fabricated under different conditions was also discussed. - Graphical abstract: Different bismuth subcarbonate ((BiO)2CO3) nanostructures were successfully synthesized by a simple solvothermal method. It was found that the solvents and precursors have an influence on the morphologies of (BiO)2CO3 nanostructures.

  16. Aerosol deposition of (Cu,Ti) substituted bismuth vanadate films

    International Nuclear Information System (INIS)

    Bismuth vanadate, Bi4V2O11, and related compounds with various metal (Me) substitutions, Bi4(MexV1−x)2O11−δ, show some of the highest ionic conductivities among the known solid oxide electrolytes. Films of Cu and Ti substituted bismuth vanadate were prepared by an aerosol deposition method, a spray coating process also described as room temperature impact consolidation. Resultant films, several microns in thickness, were dense with good adhesion to the substrate. Scanning electron microscopy and high temperature X-ray diffraction were used to monitor the effects of temperature on the structure and microstructure of the film. The particle size remained nano-scale while microstrain decreased rapidly up to 500 °C, above which coarsening and texturing increased rapidly. Impedance measurements of films deposited on inter-digital electrodes revealed an annealing effect on the ionic conductivity, with the conductivity exceeding that of a screen printed film, and approaching that of bulk ceramic. - Highlights: • Cu and Ti doped bismuth vanadate films were prepared by aerosol deposition (AD). • Dense 3–5 μm thick films were deposited on alumina, silicon and gold electrodes. • Annealing of the AD-layer increases the conductivity by 1.5 orders of magnitude. • Effect of temperature on structure and microstructure was investigated

  17. Atomic Layer Deposition of Bismuth Vanadates for Solar Energy Materials.

    Science.gov (United States)

    Stefik, Morgan

    2016-07-01

    The fabrication of porous nanocomposites is key to the advancement of energy conversion and storage devices that interface with electrolytes. Bismuth vanadate, BiVO4 , is a promising oxide for solar water splitting where the controlled fabrication of BiVO4 layers within porous, conducting scaffolds has remained a challenge. Here, the atomic layer deposition of bismuth vanadates is reported from BiPh3 , vanadium(V) oxytriisopropoxide, and water. The resulting films have tunable stoichiometry and may be crystallized to form the photoactive scheelite structure of BiVO4 . A selective etching process was used with vanadium-rich depositions to enable the synthesis of phase-pure BiVO4 after spinodal decomposition. BiVO4 thin films were measured for photoelectrochemical performance under AM 1.5 illumination. The average photocurrents were 1.17 mA cm(-2) at 1.23 V versus the reversible hydrogen electrode using a hole-scavenging sulfite electrolyte. The capability to deposit conformal bismuth vanadates will enable a new generation of nanocomposite architectures for solar water splitting. PMID:27246652

  18. Study of barium bismuth titanate prepared by mechanochemical synthesis

    Directory of Open Access Journals (Sweden)

    Lazarević Z.Ž.

    2009-01-01

    Full Text Available Barium-bismuth titanate, BaBi4Ti4O15 (BBT, a member of Aurivillius bismuth-based layer-structure perovskites, was prepared from stoichiometric amounts of barium titanate and bismuth titanate obtained via mechanochemical synthesis. Mechanochemical synthesis was performed in air atmosphere in a planetary ball mill. The reaction mechanism of BaBi4Ti4O15 and the preparation and characteristics of BBT ceramic powders were studied using XRD, Raman spectroscopy, particle analysis and SEM. The Bi-layered perovskite structure of BaBi4Ti4O15 ceramic forms at 1100 °C for 4 h without a pre-calcination step. The microstructure of BaBi4Ti4O15 exhibits plate-like grains typical for the Bi-layered structured material and spherical and polygonal grains. The Ba2+ addition leads to changes in the microstructure development, particularly in the change of the average grain size.

  19. Aerosol deposition of (Cu,Ti) substituted bismuth vanadate films

    Energy Technology Data Exchange (ETDEWEB)

    Exner, Jörg, E-mail: Functional.Materials@Uni-Bayreuth.de [University of Bayreuth, Department of Functional Materials, Universitätsstraße 30, 95440 Bayreuth (Germany); Fuierer, Paul [Materials and Metallurgical Engineering Department, New Mexico Institute of Mining and Technology, Socorro, NM 87801 (United States); Moos, Ralf [University of Bayreuth, Department of Functional Materials, Universitätsstraße 30, 95440 Bayreuth (Germany)

    2014-12-31

    Bismuth vanadate, Bi{sub 4}V{sub 2}O{sub 11}, and related compounds with various metal (Me) substitutions, Bi{sub 4}(Me{sub x}V{sub 1−x}){sub 2}O{sub 11−δ}, show some of the highest ionic conductivities among the known solid oxide electrolytes. Films of Cu and Ti substituted bismuth vanadate were prepared by an aerosol deposition method, a spray coating process also described as room temperature impact consolidation. Resultant films, several microns in thickness, were dense with good adhesion to the substrate. Scanning electron microscopy and high temperature X-ray diffraction were used to monitor the effects of temperature on the structure and microstructure of the film. The particle size remained nano-scale while microstrain decreased rapidly up to 500 °C, above which coarsening and texturing increased rapidly. Impedance measurements of films deposited on inter-digital electrodes revealed an annealing effect on the ionic conductivity, with the conductivity exceeding that of a screen printed film, and approaching that of bulk ceramic. - Highlights: • Cu and Ti doped bismuth vanadate films were prepared by aerosol deposition (AD). • Dense 3–5 μm thick films were deposited on alumina, silicon and gold electrodes. • Annealing of the AD-layer increases the conductivity by 1.5 orders of magnitude. • Effect of temperature on structure and microstructure was investigated.

  20. Word order in the Germanic languages

    DEFF Research Database (Denmark)

    Holmberg, Anders; Rijkhoff, Jan

    The Germanic branch of Indo-European consists of three main groups (Ruhlen 1987: 327):- East Germanic: Gothic, Vandalic, Burgundian (all extinct);- North Germanic (or: Scandinavian): Runic (extinct), Danish, Swedish, Norwegian, Icelandic, Faroese;- West Germanic: German, Yiddish, Luxembourgeois......, Dutch, Afrikaans, Frisian, English.Here we will only consider the languages that are currently spoken in geographical Europe. Thus Afrikaans, which is spoken in South Africa, and the extinct languages Gothic, Vandalic, Burgundian, and Runic will not be taken into account (but see e.g. König & van der...

  1. Properties of lead-bismuth coolant and perspectives of non-electric applications of lead-bismuth reactor

    International Nuclear Information System (INIS)

    Key physical and chemical properties of lead-bismuth eutectic alloy are reviewed. Based on the low chemical activity of the alloy to other work media, a new concept of direct contact heat exchangers is proposed. A series of experiments were performed to validate the concept, using water, model salt solutions of sodium chloride, and oil. Key experimental results are summarized in the report. (author)

  2. Bismuth Propellant Feed System Development at NASA-MSFC

    Science.gov (United States)

    Polzin, Kurt A.

    2007-01-01

    NASA-MSFC has been developing liquid metal propellant feed systems capable of delivering molten bismuth at a prescribed mass flow rate to the vaporizer of an electric thruster. The first such system was delivered to NASA-JPL as part of the Very High Isp Thruster with Anode Layer (VHITAL) program. In this system, the components pictured were placed in a vacuum chamber and heated while the control electronics were located outside the chamber. The system was successfully operated at JPL in conjunction with a propellant vaporizer, and data was obtained demonstrating a new liquid bismuth flow sensing technique developed at MSFC. The present effort is aimed at producing a feed-system for use in conjunction with a bismuth-fed Hall thruster developed by Busek Co. Developing this system is more ambitious, however, in that it is designed to self-contain all the control electronics inside the same vacuum chamber as an operating bismuth-fed thruster. Consequently, the entire system, including an on-board computer, DC-output power supplies, and a gas-pressurization electro-pneumatic regulator, must be designed to survive a vacuum environment and shielded to keep bismuth plasma from intruding on the electronics and causing a shortcircuit. In addition, the hot portions of the feed system must be thermally isolated from the electronics to avoid failure due to high heat loads. This is accomplished using a thermal protection system (TPS) consisting of multiple layers of aluminum foil. The only penetrations into the vacuum chamber are an electrically isolated (floating) 48 VDC line and a fiberoptic line. The 48 VDC provides power for operation of the power supplies and electronics co-located with the system in the vacuum chamber. The fiberoptic Ethernet connection is used to communicate user-input control commands to the on-board computer and transmit real-time data back to the external computer. The partially assembled second-generation system is shown. Before testing at Busek, a

  3. Study on corrosion test techniques in lead bismuth eutectic flow. Joint research report in JFY2002

    International Nuclear Information System (INIS)

    The evaluation of corrosion behaviors of core and structural materials in lead bismuth eutectic is one of the key issues for the utilization of lead bismuth eutectic as a coolant of the primary loops of lead bismuth cooled fast breeder reactors (FBRs) and the intermediate heat transport media of new-type steam generators of the sodium cooled FBRs. The purpose of the present study is to establish corrosion test techniques in lead bismuth eutectic flow. The techniques of steel corrosion test and oxygen control in flowing lead bismuth eutectic, and the technologies of a lead bismuth flow test at high temperature and high velocity were developed through corrosion test using a lead bismuth flow test loop of the Tokyo Institute of Technology in JFY2002. The major results are summarized as follows: (1) Techniques of fabrication, mount and rinse of corrosion specimens, measurement method of weight loss, and SEM/EDX analysis method have been established through lead bismuth corrosion test. (2) Weight losses were measured, corrosion and lead bismuth-adhered layers and eroded parts were observed in two 1000 hr-corrosion tests, and the results were compared with each other for twelve existing steels including ODS, F82H and SUH-3. (3) An oxygen sensor made of zirconia electrolyte structurally resistant to thermal stress and thermal shock was developed and tested in the lead bismuth flow loop. Good performance has been obtained. (4) An oxygen control method by injecting argon and hydrogen mixture gas containing steam into lead bismuth was applied to the lead bismuth flow loop, and technical issues for the development of the oxygen control method were extracted. (5) Technical measures for freezing and leakage of lead bismuth in the flow loop were accumulated. (6) Technical measures for flow rate decrease/blockage due to precipitation of oxide and corrosion products in a low temperature section of the lead bismuth flow loop were accumulated. (7) Electromagnetic flow meters with MI

  4. The accurate determination of bismuth in lead concentrates and other non-ferrous materials by AAS after separation and preconcentration of the bismuth with mercaptoacetic acid.

    Science.gov (United States)

    Howell, D J; Dohnt, B R

    1982-05-01

    A method for determining 0.0001% and upwards of bismuth in lead, zinc or copper concentrates, metals or alloys and other smelter residues is described. Bismuth is separated from lead, iron and gangue materials with mercaptoacetic acid after reduction of the iron with hydrazine. Large quantities of tin can be removed during the dissolution. An additional separation is made for materials high in copper and/or sulphate. The separated and concentrated bismuth is determined by atomic-absorption spectrometry using the Bi line at 223.1 nm. The proposed method also allows the simultaneous separation and determination of silver. PMID:18963145

  5. German energy market in 2015

    International Nuclear Information System (INIS)

    The given basic orientation of the energy concept of the federal government for the German energy supply increased towards renewable energy while increasing energy efficiency determines the market trend. In the present case, a current overview of the German energy market will be given of this year providing a concentrated compilation of the central main features of the energy industry. As in previous years, the article summarizes not only general facts about the energy, but also goes in detail on the development of the individual fuels such as oil, natural gas, lignite and hard coal, nuclear energy and renewable energies. Furthermore, the price trends are described in the international markets and in the domestic market.

  6. German cross-cultural psychology

    OpenAIRE

    Trommsdorff, Gisela

    1986-01-01

    The present study deals with German-language cross-cultural research in different fields of psychology which attempts to achieve one Or more goals of cross-cultural psychology. First, methodological problems are discussed, followed by a selective presentation of cross-cultural research in personality, clinical, ethological, developmental, and social psychology. The theoretical and methodological advancement of these studies is investigated with respect to four approaches - universals in cross...

  7. German energy policy; Deutsche Energiepolitik

    Energy Technology Data Exchange (ETDEWEB)

    Kleinwaechter, L. (ed.)

    2007-07-01

    In his introductory paper on energy supply assurance, Frank Umbach analyzes central challenges in energy supply in Europe and the USA in the decades to come. He assumes that petroleum and natural gas will continue to be important energy sources for some time to come. Roland Goetz investigates the role of Russia in petroleum and natural gas supply and points out the mutual interdependence: While Russia is the most important energy supplier for the EU, Western Europe is the biggest market for Russian energy sources. Elisabeth strecker investigates the subject of energy from an information and communication aspect. For example, different scales and forecasts of resources, ranges, production volumes and prices are the result of an information policy governed by specific interests. Kai Kleinwaechter goes into the current problem of electricity market regulation in Germany. Starting from a historical outline, the financial, oranisational and personal interdependences between the EU, the German government, the German states governments, public utilities and industrial consumers (''iron pentagram'') are presented. WErner Schilling discusses energy policy on a state basis, using the example of the German state of Brandenburg (orig.)

  8. Selective oxidation of propylene to acrolein by silica-supported bismuth molybdate catalysts

    DEFF Research Database (Denmark)

    Duc, Duc Truong; Ha, Hanh Nguyen; Fehrmann, Rasmus;

    2011-01-01

    Silica-supported bismuth molybdate catalysts have been prepared by impregnation, structurally characterized and examined as improved catalysts for the selective oxidation of propylene to acrolein. Catalysts with a wide range of loadings (from 10 to 90 wt%) of beta bismuth molybdate (β-Bi2Mo2O9) w...

  9. Attenuation and image quality in the use of protective bismuth in chest CT scans

    International Nuclear Information System (INIS)

    For chest CT scans are protective of bismuth (Bi) with the aim of reducing the dose in the breast. The aim of this study was to evaluate the attenuation with thermoluminescent dosimeters in the glandular dose average when using these protective breast CT scans and to evaluate the image quality with and without protective Bismuth.

  10. Electronic Properties of Tin and Bismuth from Angular Correlation of Annihilation Photons

    DEFF Research Database (Denmark)

    Mogensen, O.E.; Trumpy, Georg

    1969-01-01

    liquid-metal curves are smaller and of another form than the tails of polycrystalline curves; no Gaussian with only one adjustable constant factor can give a fit to both tails. No useful method for interpreting liquid-metal angular-correlation curves seems to exist. Two deformed bismuth samples gave......A linear slit setup has been used to obtain results of angular-correlation measurements in (a) tin single crystals in three orientations: [001], [100], and [110], (b) bismuth single crystals in four orientations: [111], [100], [1¯10], and [2¯1¯1], (c) solid and liquid tin and bismuth, and (d......) deformed bismuth. For both metals, the single-crystal angular-correlation curves lie near to the free-electron parabola. The tin curves show more anisotropy than the bismuth curves. An important result is the clear anisotropy found in the high-momentum part of the curves—the tails—for both metals. Little...

  11. Conduction mechanism in bismuth silicate glasses containing titanium

    International Nuclear Information System (INIS)

    Bismuth silicate glasses mixed with different concentrations of titanium dioxide having compositions xTiO2–(60−x)Bi2O3–40SiO2 with x=0, 5, 10, 15 and 20 were prepared by the normal melt quench technique. The frequency dependence of the ac electrical conductivity of different compositions of titanium bismuth silicate glasses has been studied in the frequency range 10−1 Hz to 10 MHz and in the temperature range 623–703 K. The temperature and frequency dependent conductivity is found to obey Jonscher's universal power law for all the compositions of titanium bismuth silicate glass system. The dc conductivity (σdc), so called crossover frequency (ωH), and frequency exponent (s) have been estimated from the fitting of experimental data of ac conductivity with Jonscher's universal power law. Enthalpy to dissociate the cation from its original site next to a charge compensating center (Hf) and enthalpy of migration (Hm) have also been estimated. The conductivity data have been analyzed in terms of different theoretical models to determine the possible conduction mechanism. Analysis of the conductivity data and the frequency exponent shows that the correlated barrier hopping of electrons between Ti3+ and Ti4+ ions in the glasses is the most favorable mechanism for ac conduction. The temperature dependent dc conductivity has been analyzed in the framework of theoretical variable range hopping model (VRH) proposed by Mott which describe the hopping conduction in disordered semiconducting systems. The various polaron hopping parameters have also been deduced. Mott's VRH model is found to be in good agreement with experimental data and the values of inverse localization length of s-like wave function (α) obtained by this model with modifications suggested by Punia et al. are close to the ones reported for a number of oxide glasses

  12. Effect of FGMs on thermoelectric cooling properties of bismuth telluride

    International Nuclear Information System (INIS)

    Every thermoelectric material shows high performance at a specific narrow temperature range. The temperature range with high performance can be expanded by joining the materials with different peak temperature. This is the concept of an FGM. The FGMs for Peltier cooling materials have never been reported though the FGMs for thermoelectric power generation were reported to enhance conversion efficiency. Bismuth telluride is the best material for cooling devices at around room temperature. Then we investigated the thermoelectric cooling properties for bismuth telluride with two steps graded structure FGM. Two kinds of melt-grown materials of p-type bismuth telluride (hereafter, sample 1 and sample 2) were used. The samples 1 and 2 of 3 mm square x 2.5 mm were joined to form an FGM of 3 mm square x 5 mm in length by soldering with ultrasonic vibration. Thermoelectric cooling properties were evaluated by observing the maximum temperature drop to electric current when the high temperature side was kept constant. When the high temperature side is kept at 370 K, the temperature drop of the monolithic sample 1 was 34.6 K, and 39.7 K for sample 2, because of the difference of the carrier density. In the case of the FGM, the temperature drop was 45.2 K when the sample 1 was placed at the high temperature side. On the other hand, the temperature drop was only 27.6 K when the sample 2 was placed at the high temperature side. From these results, it is clear that high performance can be obtained by forming an FGM when the proper material arrangement is performed along the temperature gradient. (orig.)

  13. Yttrium bismuth titanate pyrochlore mixed oxides for photocatalytic hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Merka, Oliver

    2012-10-18

    In this work, the sol-gel synthesis of new non-stoichiometric pyrochlore titanates and their application in photocatalytic hydrogen production is reported. Visible light response is achieved by introducing bismuth on the A site or by doping the B site by transition metal cations featuring partially filled d orbitals. This work clearly focusses on atomic scale structural changes induced by the systematical introduction of non-stoichiometry in pyrochlore mixed oxides and the resulting influence on the activity in photocatalytic hydrogen production. The materials were characterized in detail regarding their optical properties and their atomic structure. The pyrochlore structure tolerates tremendous stoichiometry variations. The non-stoichiometry in A{sub 2}O{sub 3} rich compositions is compensated by distortions in the cationic sub-lattice for the smaller Y{sup 3+} cation and by evolution of a secondary phase for the larger Bi{sup 3+} cation on the A site. For TiO{sub 2} rich compositions, the non-stoichiometry leads to a special vacancy formation in the A and optionally O' sites. It is shown that pyrochlore mixed oxides in the yttrium bismuth titanate system represent very active and promising materials for photocatalytic hydrogen production, if precisely and carefully tuned. Whereas Y{sub 2}Ti{sub 2}O{sub 7} yields stable hydrogen production rates over time, the bismuth richer compounds of YBiTi{sub 2}O{sub 7} and Bi{sub 2}Ti{sub 2}O{sub 7} are found to be not stable under irradiation. This drawback is overcome by applying a special co-catalyst system consisting of a precious metal core and a Cr{sub 2}O{sub 3} shell on the photocatalysts.

  14. Determination of lead-210 in bottom sediments via bismuth-210

    International Nuclear Information System (INIS)

    Determination of lead-210 in bottom sediments is applied for evaluation of sedimentation rates and sediments ages by concentration profiles of disequilibrated lead-210 from atmospheric sources. Advances in low level liquid scintillation spectrometry (LS) fitted for natural radioactivity measurements, permit to combine the possibility of immediate bismuth-210 separation with its radioactivity registration using LS spectrometer Quantulus (LKS-1220, Wallak, Finland). The method was tested on bottom sediment samples from Baltic Sea shelf, collected during the 76th cruise of RV 'Academician S. Vavilov'. (author) 6 refs.; 1 tab

  15. Thermal-hydraulics of lead bismuth for accelerator driven systems

    International Nuclear Information System (INIS)

    Full text of publication follows: Lead bismuth has been selected as one of the most suitable coolants to be used in accelerator driven systems (ADS) for transmutation of minor actinides. It serves both, as a target material of the spallation source to balance the neutron economy, and as a coolant with high thermal inertia to provide a safe and reliable heat transfer to the secondary power cycle. With the aim to develop the required technologies to enable the later design of such ADS systems, the Karlsruhe Lead bismuth LAboratory KALLA, consisting of three test loops, has been built and set into operation at the Forschungszentrum Karlsruhe since 2000, keeping more than 45 t of PbBi in operation at temperatures up to 550 deg. C. The test program includes oxygen control systems, heat flux simulation tools, electro-magnetic and mechanical pump technologies, heat transfer and flow measurements, reliability and corrosion tests. In a first test campaign, a technology loop called THESYS was built to develop measurement technologies for the acquisition of scalar quantities, like pressures, temperatures, concentrations, and flow rates, as well as velocity fields, which are required for both operational and scientific purposes. THESYS also allowed to perform generic turbulent heat transfer experiments necessary to provide liquid metal adapted turbulent heat transfer models for ADS design analyses. The second loop, the thermalhydraulic loop THEADES with an installed power of 2.5 MW, has been built to conduct prototypical component experiments for beam windows (e.g. MEGAPIE or MYHRRA) or fuel rod configurations. First test results will be reported. The experimental team is supported by a numerical team who studied the thermal hydraulics of the tested components in order to enable a later transfer of the results to industrial systems. Three different types of codes are being improved: lumped parameter codes (e.g. ATHLET) to perform system analyses for lead bismuth in loops

  16. Colloidal bismuth subcitrate in non-ulcer dyspepsia.

    OpenAIRE

    Khanna M; Abraham P; Nair N; Mistry F; Vora I

    1992-01-01

    The effect of colloidal bismuth subcitrate (De-Nol) on symptoms, Helicobacter pylori status and histological features was studied in 35 patients with non-ulcer dyspepsia. Pain (34 cases) and gas bloat (18) were the predominant symptoms. H pylori was present in 26 (74.3%) patients. Gastritis and duodenitis were present in 29 of 32 and 22 of 31 cases respectively in whom biopsies were available. Relief in symptoms after treatment was seen in 29 (82.8%) cases. Improvement in gastri...

  17. Fano interference for large-amplitude coherent phonons in bismuth

    International Nuclear Information System (INIS)

    We report femtosecond time-resolved measurements of lattice dynamics in bismuth made over a wide range of temperatures and excitation levels. We demonstrate that time-integrated Fourier transforms for both the fully symmetric A1g and doubly degenerate Eg coherent oscillations of large amplitude exhibit asymmetric line shapes described by the Fano formula. Measuring the real and imaginary part of the phonon self-energy, we attempt to identify the nature of the continuum responsible for the configuration mixing. Based on the measured pump and temperature dependences, we suggest that the continuum responsible for the interference includes both the electronic and lattice degrees of freedom

  18. Melting and solidification of bismuth inclusions in aluminium

    DEFF Research Database (Denmark)

    Thoft, N.B.; Bohr, J.; Buras, B.;

    1995-01-01

    experimental methods (and on different samples) agree remarkably well. The inclusions melt at temperatures at or below the bismuth bulk melting point, and the solid/liquid phase transition exhibits a hysteresis of 100-150 K. Average inclusion sizes ranged from a few nm to some tens of nm. The x-ray diffraction...... melting data are discussed in relation to different existing models for the melting temperature of an inclusion as a function of its size. From this an approximate size distribution for the inclusions is derived....

  19. Gamma-ray attenuation coefficients in bismuth borate glasses

    International Nuclear Information System (INIS)

    Mass attenuation coefficients of glasses in the system: xBi2O3(1-x)B2O3 (x=0.30, 0.35, 0.40, 0.45 and 0.55) were determined at 356, 662, 1173 and 1332 keV photon energies using a narrow beam transmission method. Appreciable variations were observed in these coefficients due to changes in the chemical composition of glasses. These coefficients were then used to determine effective atomic numbers of glass samples, which were found to be constant with bismuth concentration and energy

  20. STM observation of twin microlayers on cleaved bismuth surfaces

    Science.gov (United States)

    Edel'man, V. S.

    1996-02-01

    Scanning tunneling microscopy of cleaved bismuth surfaces at low temperatures revealed the presence of thin twin microlayers, whose width ∼70 Å is determined by the fact that the height gained in crossing such a microlayer due to its tilt with respect to the surface of the undisturbed crystal equals the interlunar distance in the [0001] direction. The microlayers were strictly aligned with the surface atomic rows. Their lengths were macroscopically large, being no smaller than a few fractions of a micron. It was found that, near the microlayer boundaries, the electron properties were significantly different from those at other points on the surface.

  1. LOVE IN GERMAN AND SERBIAN IDIOMS

    Directory of Open Access Journals (Sweden)

    Gordana Ristić

    2012-12-01

    Full Text Available The aim of the paper is to carry through a comparative study of somatic idioms in the semantic field of LOVE in German and Serbian language, on the basis of the cognitive and conceptual linguistic theory. The somatisms will be examined from the interlingual German-Serbian aspect, with German being the source language, and Serbian the target language. The corpus has been excerpted from the relevant monolingual and bilingual idiom dictionaries.

  2. Geogenic heavy metal concentrations in German soils

    International Nuclear Information System (INIS)

    In the area of the German Federal Republic, 6,300 soil samples of 526 soil profiles were examined for the concentrations of lead, copper, zinc, cadmium, nickel, cobalt, mercury, antimony, arsenic and lithium. The soil profiles were selected so that the prevailing loose and solid rock floors of the German Federal Republic were represented. The analysis data of these samples formed the basis for the calculation of average geogenic heavy metal concentrations in the soils of the German Federal Republic. (orig.)

  3. DIMA – Annotation guidelines for German intonation

    OpenAIRE

    Kügler, Frank; Smolibocki, Bernadett; Arnold, Denis; Baumann, Stefan; Braun, Bettina; Grice, Martine; Jannedy, Stefanie; Michalsky, Jan; Niebuhr, Oliver; Peters, Jörg; Ritter, Simon; Röhr, Christine T.; Schweitzer, Antje; Schweitzer, Katrin; Wagner, Petra

    2015-01-01

    This paper presents newly developed guidelines for prosodic annotation of German as a consensus system agreed upon by German intonologists. The DIMA system is rooted in the framework of autosegmental-metrical phonology. One important goal of the consensus is to make exchanging data between groups easier since German intonation is currently annotated according to different models. To this end, we aim to provide guidelines that are easy to learn. The guidelines were e...

  4. Semantic gender agreement: Dutch and German compared

    OpenAIRE

    Kraaikamp, M. Van

    2016-01-01

    This paper compares pronominal gender agreement in Dutch and German. Pronouns do not always agree with the gender of their antecedent: instead of agreeing with the lexical gender of the noun, they show semantic gender agreement. This is known to occur with human referents in both Dutch and German. In Dutch, pronouns can agree semantically with non-human referents as well, based on their degree of individuation. This type of agreement has been found in several Germanic varieties. It has been s...

  5. Out of the German parliament into the German Museum?

    International Nuclear Information System (INIS)

    It is currently discussed whether the German Bundestag can deal with the interdepartmental problems of technology assessment with the Commissions of Inquiry on the one hand and whether it has adequate instruments available with the department-related standing Bundestag committees in order to deal with technology assessment. In its report the Commission of Inquiry for Technology Assessment of the past legislative period came to the conclusion that the US parliamentary advisory model which has been realized with OTA could, of course, not be transferred to the situation of the German Bundestag without hesitation, but that the Bundestag should also have a permanent scientific department staff with a sufficient number of personnel and material. The congress was to offer the possibility to discuss the problems of technology assessment with regard to this up-to-date background with experts and members of parliament of the various commissions of inquiry and commissions of the Bundestag which were summoned in order to judge essential technologies and also to solve the problem of the institutionalization of technology assessment. (orig./DG)

  6. German versus Nordic Board Models

    DEFF Research Database (Denmark)

    Ringe, Georg

    2016-01-01

    Board structure is an important component of the individual governance of firms, and the appropriateness of the various models is one of the most debated issues in corporate governance today. A comparison of the Nordic and German approaches to the structure of corporate boards reveals stark...... changes and developments in business practice, the article argues that board practices in the two systems effectively blur the structural distinction, and that board organization is converging in practice. It thereby contributes to the broader debates on functionality and comparative corporate law and...

  7. 63rd German radiological congress

    International Nuclear Information System (INIS)

    The book of abstracts contains abstracts of 171 papers read at the German Radiological Congress in Berlin as well as abstracts of two papers not read for lack of time. Further, there are 31 brief descriptions of the scientific exhibition. Subjects: Diagnosis of gall bladder diseases and inflammatory diseases of the large intestine; hyperthermia and irradiation in tumour therapy; nuclear methods in the diagnosis of growing and displacing processes, skeletal diseases, thromboses, embolisms, gastrointestinal and liver affections; new techniques and methods, diagnostics of the spinal tract; radiooncology; carcinoma of the ovaries; diagnostics and therapy of tumours of the lungs; computerized tomography; angiography; ultrasonic diagnosis. (MG)

  8. German Medical Science - "open access" ist erfolgreich

    OpenAIRE

    Müller, W.

    2008-01-01

    Im Portal German Medical Science (gemeinschaftlich betrieben von AWMF, DIMDI und ZB MED) werden zur Zeit 13 Zeitschriften und eine Schriftenreihe elektronisch mit freiem Zugriff ("open access") publiziert:

  9. The Proto-Germanic n-stems

    DEFF Research Database (Denmark)

    Kroonen, Guus Jan

    The n-stems are an intriguing part of Proto-Germanic morphology. Unlike any other noun class, the n-stems have roots that are characterized by systematic consonant and vowel alternations across the different Germanic dialects. This monograph represents a diachronic investigation of this root...... variation. It traces back the Germanic n-stems to their Indo-European origin, and clarifies their formal characteristics by an interaction of sound law and analogy. This book therefore is not just an attempt to account for the typology of the Germanic n-stems, but also a case study of the impact that sound...

  10. Investigation of corrosion, water reaction, polonium evaporation and bismuth resource in liquid metal lead-bismuth technology

    Energy Technology Data Exchange (ETDEWEB)

    Takano, Hideki; Takizuka, Takakazu [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kitano, Teruaki [Mitsui Shipbuilding and Engineering Co. Ltd., Tokyo (Japan)

    2000-10-01

    Lead-bismuth is the first candidate material for liquid metal target find coolant of fueled blanket system in accelerator-driven system (ADS) studied at JAERI. Advantages of the lead-bismuth utilization are non-active material, very low capture cross section, low melting point of 125degC and high boiling point of 1670degC, and beside coolant void reactivity become negative. But problems are due to the high corrosivity to most of the structural materials and the corrosive data are scarcity. In this report, corrosivity, reaction with water, thermal-hydraulics, chemical toxicity etc. are studied by investigating some facilities utilized and researched really for lead or lead-bismuth. And, furthermore, polonium evaporation rate and bismuth resource are investigated. Main results obtained are as follows: (1) In a refinery, there are enough employment experience for liquid Pb-Bi in period of about 17 years and not corrosion for the thermal conductive materials (1Cr-0.5Mo steel) used under the condition of natural convection with temperature around 400degC. (2) In Russia, extensive experience in the use as Russian submarines and in R and D during about 50 years are available. And as a result, it will be able to lead approximately zero corrosion for Cr-Si materials by adjusting oxygen film with oxygen concentration control between 10{sup -7} to 10{sup -5}% mass. However, the corrosion data are not enough systematically collected involving them in radiation dose field. (3) In liquid-dropping experiment, it is shown that interaction between water and high temperature liquid Pb-Bi is reduced steeply with rising of atmosphere pressure. But, in order to design the second circuit removal model of ADS, the interaction should be evaluated by water continuous injection experiment. (4) Polonium forms PbPo in Pb-Bi, and the evaporation rate become less three factor than that of Po, and furthermore, the rate decreases in the atmosphere. The effects of Po on employee and environment

  11. Investigation of corrosion, water reaction, polonium evaporation and bismuth resource in liquid metal lead-bismuth technology

    International Nuclear Information System (INIS)

    Lead-bismuth is the first candidate material for liquid metal target find coolant of fueled blanket system in accelerator-driven system (ADS) studied at JAERI. Advantages of the lead-bismuth utilization are non-active material, very low capture cross section, low melting point of 125degC and high boiling point of 1670degC, and beside coolant void reactivity become negative. But problems are due to the high corrosivity to most of the structural materials and the corrosive data are scarcity. In this report, corrosivity, reaction with water, thermal-hydraulics, chemical toxicity etc. are studied by investigating some facilities utilized and researched really for lead or lead-bismuth. And, furthermore, polonium evaporation rate and bismuth resource are investigated. Main results obtained are as follows: (1) In a refinery, there are enough employment experience for liquid Pb-Bi in period of about 17 years and not corrosion for the thermal conductive materials (1Cr-0.5Mo steel) used under the condition of natural convection with temperature around 400degC. (2) In Russia, extensive experience in the use as Russian submarines and in R and D during about 50 years are available. And as a result, it will be able to lead approximately zero corrosion for Cr-Si materials by adjusting oxygen film with oxygen concentration control between 10-7 to 10-5% mass. However, the corrosion data are not enough systematically collected involving them in radiation dose field. (3) In liquid-dropping experiment, it is shown that interaction between water and high temperature liquid Pb-Bi is reduced steeply with rising of atmosphere pressure. But, in order to design the second circuit removal model of ADS, the interaction should be evaluated by water continuous injection experiment. (4) Polonium forms PbPo in Pb-Bi, and the evaporation rate become less three factor than that of Po, and furthermore, the rate decreases in the atmosphere. The effects of Po on employee and environment will not be

  12. Deutschunterricht und deutsche Hochlautung (German Instruction and the High German Pronunciation)

    Science.gov (United States)

    Kelz, Heinrich P.

    1976-01-01

    Discusses the questions of which pronunciation model should be used in German courses and how closely students should be expected to duplicate it. After a short history of efforts to standardize German, it is suggested that the new "Aussprache Duden" is a good basis for teaching pronunciation. (Text is in German.) (TL)

  13. French pollution and German lignite

    International Nuclear Information System (INIS)

    After having recalled that the German energy transition is based on a complete shutting down of nuclear power stations to replace them by renewable energy sources on the one hand, and by coal (lignite, i.e. the dirtiest coal) and gas on the other hand to compensate the intermittency of the former ones, this article notices that pollution peaks occurred in France when an eastern of north-eastern wind was blowing, and not in case of western wind. The author then wanders whether this pollution comes from Germany, and more particularly from the releases of lignite-fuelled power stations. Then, the author comments the high level of pollution associated with coal extraction and exploitation in Germany, causing thousands of deaths and resulting in lung diseases or cancers, myocardial infractions. The author then makes a parallel between, on the one hand, the ignorance of this German pollution and, on the other hand, evacuation measures around Fukushima for a radioactivity which the author considers as less dangerous in terms of life expectancy

  14. Synthesis and characterization of bismuth alkaline titanate powders

    International Nuclear Information System (INIS)

    In this work, samples of bismuth alkaline titanate, (K0.5Na0.5)(2-x/2)Bi(x/6)TiO3, (x = 0.05-0.75) have been prepared by conventional ceramic technique and molten salts. Metal oxides or carbonates powders were used as starting raw materials. The crystalline phase of the synthesized powders was identified by the X-ray diffraction (XRD) and particle morphology was characterized by scanning electron microscopy (SEM). Solid state reaction method was unsuccessful to obtain pellets. From XRD results, a rhombohedral structure was detected and the parameter lattice were estimated to be a = 5.5478 A and α = 59.48o. These parameters were used to refine the structure by Rietveld analysis. SEM results showed several morphologies. Apparently, bismuth is promoting the grain growth whose sizes vary from 30 nm to 180 nm It is expected that these materials can be utilized in practical applications as substitutes for lead zirconatetitanate (PZT)-based ceramics.

  15. Field-induced polarization of Dirac valleys in bismuth

    Science.gov (United States)

    Behnia, Kamran; Zhu, Zengwei; Callaudin, Aurelie; Fauque, Benoit; Kang, Woun

    2012-02-01

    The principal challenge in the field of ``valleytronics'' is to lift the valley degeneracy of electrons in a controlled way. In graphene, a number of methods to generate a valley-polarized flow of electrons have been proposed, which are yet to be experimentally realized. In bulk semi-metallic bismuth, the Fermi surface includes three cigar-shaped electron valleys lying almost perpendicular to the high-symmetry axis known as the trigonal axis. The in-plane mass anisotropy of each valley exceeds 200 as a consequence of Dirac dispersion, which drastically reduces the effective mass along two out of the three orientations. We present a study of angle-dependent magnetoresistance in bismuth which shows that a flow of Dirac electrons along the trigonal axis is extremely sensitive to the orientation of in-plane magnetic field. The effect is visible even at room temperature. Thus, a rotatable magnetic field can be used as a valley valve to tune the contribution of each valley to the total conductivity. At high temperature and low magnetic field, the three valleys are interchangeable and the three-fold symmetry of the underlying lattice is respected. As the temperature is decreased or the magnetic field increased, this symmetry is spontaneously lost. This loss may be an experimental manifestation of the recently proposed valley-nematic Fermi liquid state.

  16. Electrodeposition of bismuth alloys by the controlled potential method

    International Nuclear Information System (INIS)

    We worked with the electrodeposition of three bismuth alloys, the composition of the first electrolyte was: 0.3 g/l. Bi; 20 g/l. Ni; and the conditions were pH = 5.2 - 5.6; T = 25 Centigrade degrees; current density 0.3 A / dm2 - 6.6 A / dm2. Following alloy was between Bi - Pb, composition of the electrolyte was 3.18 g/l. Bi (metallic); 31.81 g/l. Pb (Pb(NO3)2) pH : 1; T = 20 Centigrade degrees; current density 10.20 A/dm2 . The third electrolyte was Bi-Cu, its composition was: 20.89 g/l. Bi; (metallic) 63.54 g/l Cu (Cu(NO3)2) pH : 1.5 - 1.8; T = 25-30 Centigrade degrees; current density 1-2 A/dm2 . The best results were obtained with the third electrolyte. The purpose of this work was to experiment with different parameters like temperature, pH and the electrolyte concentration to obtain a bismuth alloy. (Author)

  17. Magnetic anisotropies in ultrathin bismuth iron garnet films

    International Nuclear Information System (INIS)

    Ultrathin bismuth iron garnet Bi3Fe5O12 films were grown epitaxially on (001)-oriented gadolinium gallium garnet substrates. Film thickness varied from two to three dozens of unit cells. Bi3Fe5O12 films grow pseudomorphically on substrates up to a thickness of 20 nm, and then a lattice relaxation occurs. Magnetic properties of the films were studied as a function of bismuth iron garnet thickness. The magnetization and cubic anisotropy decrease with decreasing film thickness. The uniaxial magnetocrystalline anisotropy is constant for all film thicknesses. For two unit cell thick films, the easy magnetization axis changes from in-plane to perpendicular to the plane direction. Such a reorientation takes place as a result of the competition of constant uniaxial perpendicular anisotropy with weakening film magnetization. - Highlights: ► Ultrathin Bi3Fe5O12 films were grown epitaxially on structure-matching substrates. ► Magnetic properties of Bi3Fe5O12 were studied down to the thickness of 2.5 nm. ► Reorientation of easy magnetization axis as a function of film thickness was observed

  18. Layered bismuth oxyhalide nanomaterials for highly efficient tumor photodynamic therapy

    Science.gov (United States)

    Xu, Yu; Shi, Zhenzhi; Zhang, Ling'e.; Brown, Eric Michael Bratsolias; Wu, Aiguo

    2016-06-01

    Layered bismuth oxyhalide nanomaterials have received much more interest as promising photocatalysts because of their unique layered structures and high photocatalytic performance, which can be used as potential inorganic photosensitizers in tumor photodynamic therapy (PDT). In recent years, photocatalytic materials have been widely used in PDT and photothermal therapy (PTT) as inorganic photosensitizers. This investigation focuses on applying layered bismuth oxyhalide nanomaterials toward cancer PDT, an application that has never been reported so far. The results of our study indicate that the efficiency of UV-triggered PDT was highest when using BiOCl nanoplates followed by BiOCl nanosheets, and then TiO2. Of particular interest is the fact that layered BiOCl nanomaterials showed excellent PDT effects under low nanomaterial dose (20 μg mL-1) and low UV dose (2.2 mW cm-2 for 10 min) conditions, while TiO2 showed almost no therapeutic effect under the same parameters. BiOCl nanoplates and nanosheets have shown excellent performance and an extensive range of applications in PDT.

  19. Mechanically activating formation of layered structured bismuth titanate

    International Nuclear Information System (INIS)

    Bismuth titanate-Bi4Ti3O12 (BIT) with wide application in the electronic industry as capacitors, memory devices and sensors is the simplest compound in the Aurivillius family, which consists of (Bi2O2)2+ sheets alternating with (Bi2Ti3O10)2- perovskite-like layers. The synthesis of more resistive BIT ceramics would be preferable advance in obtaining of well-densified ceramic with small grains randomly oriented to limit the conductivity along the (Bi2O2)2+ layers. Having in mind that the conventional ceramic route for the synthesis can lead to non-stoichiometry in composition, in consequence of the undesirable loss in bismuth content through volatilization of Bi2O3 at elevated temperature, our efforts were addressed to preparation of BIT by mechanical activation the constituent oxides. The nucleation and phase formation of BIT, crystal structure, microstructure, powder particle size and specific surface area were followed by XRD, Rietveld refinement analysis, thermal analysis, scanning electron microscopy (SEM) and the BET specific surface area measurements

  20. Genotoxic effects of bismuth (III oxide nanoparticles by comet assay

    Directory of Open Access Journals (Sweden)

    Reecep Liman

    2015-06-01

    Full Text Available Bismuth oxide is one of the important transition metal oxides and it has been intensively studied due to their peculiar characteristics (semiconductor band gap, high refractive index, high dielectric permittivity, high oxygen conductivity, resistivity, photoconductivity and photoluminescence etc.. Therefore, it is used such as microelectronics, sensor technology, optical coatings, transparent ceramic glass manufacturing, nanoenergetic gas generator, biosensor for DNA hybridization, potential immobilizing platforms for glucose oxidase and polyphenol oxidase, fuel cells, a additive in paints, an astringent in a variety of medical creams and topical ointments, and for the determination of heavy metal ions in drinking water, mineral water and urine. In addition this, Bismuth (III oxide nanoparticles (BONPs are favorable for the biomolecules adsorption than regular sized particles because of their greater advantages and novel characteristics (much higher specific surface, greater surface free energy, and good electrochemical stability etc.. Genotoxic effects of BONPs were investigated on the root cells of Allium cepa by Comet assay. A. cepa roots were treated with the aqueous dispersions of BONPs at 5 different concentrations (12.5, 25, 50, 75, and 100 ppm for 4 h. A significant increase in DNA damage was also observed at all concentrations of BONPs except 12.5 ppm by Comet assay. The results were also analyzed statistically by using SPSS for Windows; Duncan’s multiple range test was performed. These result indicate that BONPs exhibit genotoxic activity in A. cepa root meristematic cells.

  1. Superconductivity in Bismuth. A New Look at an Old Problem.

    Science.gov (United States)

    Mata-Pinzón, Zaahel; Valladares, Ariel A; Valladares, Renela M; Valladares, Alexander

    2016-01-01

    To investigate the relationship between atomic topology, vibrational and electronic properties and superconductivity of bismuth, a 216-atom amorphous structure (a-Bi216) was computer-generated using our undermelt-quench approach. Its pair distribution function compares well with experiment. The calculated electronic and vibrational densities of states (eDOS and vDOS, respectively) show that the amorphous eDOS is about 4 times the crystalline at the Fermi energy, whereas for the vDOS the energy range of the amorphous is roughly the same as the crystalline but the shapes are quite different. A simple BCS estimate of the possible crystalline superconducting transition temperature gives an upper limit of 1.3 mK. The e-ph coupling is more preponderant in a-Bi than in crystalline bismuth (x-Bi) as indicated by the λ obtained via McMillan's formula, λc = 0.24 and experiment λa = 2.46. Therefore with respect to x-Bi, superconductivity in a-Bi is enhanced by the higher values of λ and of eDOS at the Fermi energy. PMID:26815431

  2. Synthesis and characterization of bismuth alkaline titanate powders

    Energy Technology Data Exchange (ETDEWEB)

    Torres-Huerta, A.M., E-mail: atorresh@ipn.mx [CICATA-Altamira, Instituto Politecnico Nacional, Km. 14.5 Carretera Tampico Puerto Industrial Altamira, Altamira, Tamps. 89600 (Mexico); Dominguez-Crespo, M.A. [CICATA-Altamira, Instituto Politecnico Nacional, Km. 14.5 Carretera Tampico Puerto Industrial Altamira, Altamira, Tamps. 89600 (Mexico); Hernandez-Perez, M.A. [ESIQIE, Metalurgia, Instituto Politecnico Nacional, Mexico, D. F (Mexico); Garcia-Zaleta, D.S. [CICATA-Altamira, Instituto Politecnico Nacional, Km. 14.5 Carretera Tampico Puerto Industrial Altamira, Altamira, Tamps. 89600 (Mexico); Brachetti-Sibaja, S.B. [CICATA-Altamira, Instituto Politecnico Nacional, Km. 14.5 Carretera Tampico Puerto Industrial Altamira, Altamira, Tamps. 89600 (Mexico); Instituto Tecnologico de Ciudad Madero, Av. 1o. de Mayo esq. Sor Juana Ines de la Cruz s/n Col. Los Mangos C.P.89440 Cd. Madero Tamaulipas (Mexico)

    2011-06-15

    In this work, samples of bismuth alkaline titanate, (K{sub 0.5}Na{sub 0.5}){sub (2-x/2)}Bi{sub (x/6)}TiO{sub 3}, (x = 0.05-0.75) have been prepared by conventional ceramic technique and molten salts. Metal oxides or carbonates powders were used as starting raw materials. The crystalline phase of the synthesized powders was identified by the X-ray diffraction (XRD) and particle morphology was characterized by scanning electron microscopy (SEM). Solid state reaction method was unsuccessful to obtain pellets. From XRD results, a rhombohedral structure was detected and the parameter lattice were estimated to be a = 5.5478 A and {alpha} = 59.48{sup o}. These parameters were used to refine the structure by Rietveld analysis. SEM results showed several morphologies. Apparently, bismuth is promoting the grain growth whose sizes vary from 30 nm to 180 nm It is expected that these materials can be utilized in practical applications as substitutes for lead zirconatetitanate (PZT)-based ceramics.

  3. Superconductivity in Bismuth. A New Look at an Old Problem.

    Directory of Open Access Journals (Sweden)

    Zaahel Mata-Pinzón

    Full Text Available To investigate the relationship between atomic topology, vibrational and electronic properties and superconductivity of bismuth, a 216-atom amorphous structure (a-Bi216 was computer-generated using our undermelt-quench approach. Its pair distribution function compares well with experiment. The calculated electronic and vibrational densities of states (eDOS and vDOS, respectively show that the amorphous eDOS is about 4 times the crystalline at the Fermi energy, whereas for the vDOS the energy range of the amorphous is roughly the same as the crystalline but the shapes are quite different. A simple BCS estimate of the possible crystalline superconducting transition temperature gives an upper limit of 1.3 mK. The e-ph coupling is more preponderant in a-Bi than in crystalline bismuth (x-Bi as indicated by the λ obtained via McMillan's formula, λc = 0.24 and experiment λa = 2.46. Therefore with respect to x-Bi, superconductivity in a-Bi is enhanced by the higher values of λ and of eDOS at the Fermi energy.

  4. Effect of O-vacancies on magnetic properties of bismuth ferrite nanoparticles by solution evaporation method

    Science.gov (United States)

    Afzal, A. M.; Umair, M.; Dastgeer, G.; Rizwan, M.; Yaqoob, M. Z.; Rashid, R.; Munir, H. S.

    2016-02-01

    Bismuth ferrite is a multiferroic material which shows high magnetization and polarization at room temperature. In present work, the effect of Oxygen (O) vacancies on magnetic properties of bismuth ferrite nanoparticles is studied. Bismuth ferrite nanoparticles (BiFeO3) were synthesized by solution evaporation method (SEM) at room temperature. The sample was annealed under two different atmospheres such as in air and oxygen, to check the effect of O-vacancies on magnetic properties. The average crystallite size of Bismuth ferrite nanoparticles (NPs) as calculated by X-ray diffraction (XRD) falls in the range of 23-32 nm and 26-39 nm for the case of air and oxygen respectively. The crystallite size of bismuth ferrite nanoparticles increases as the temperature was varied from 450 °C to 650 °C. Further the influence of annealing temperature on the magnetic properties of the bismuth ferrite nanoparticles was also observed. It was concluded that the magnetic properties of Bismuth ferrite nanoparticles are directly interconnected to annealing atmosphere and annealing temperature. The magnetic properties were increased in the case of oxygen annealing, which actually leads in our case to an improvement of the crystallinity.

  5. Ultra-flat bismuth films for diamagnetic levitation by template-stripping

    Energy Technology Data Exchange (ETDEWEB)

    Kokorian, J. [University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands); TU Delft — 3mE-PME, Mekelweg 2, 2628 CD Delft (Netherlands); Engelen, J.B.C. [University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands); IBM Research — Zurich, Säumerstrasse 4, CH-8803 Rüschlikon (Switzerland); Vries, J. de; Nazeer, H.; Woldering, L.A. [University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands); Abelmann, L., E-mail: l.abelmann@utwente.nl [University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands)

    2014-01-01

    In this paper we present a method to deposit thin films of bismuth with sub-nanometer surface roughness for application to diamagnetic levitation. Evaporated films of bismuth have a high surface roughness with peak to peak values in excess of 100 nm and average values on the order of 20 nm. We expose the smooth backside of the films using a template stripping method, resulting in a great reduction of the average surface roughness, to 0.8 nm. Atomic force microscope and X-ray diffraction measurements show that the films have a polycrystalline texture with preferential c-axis orientation. On the back side of the film, fine grains are grouped into larger clusters. Cantilever resonance shift measurements indicate that the Young's modulus of the films is on the order of 20 GPa. - Highlights: • We deposited continuous but rough bismuth films of 200–500 nm in thickness by thermal evaporation. • We analyzed the material properties of bismuth films using a variety of measurement techniques. • We reduced the roughness of bismuth films from 20 nm to 0.8 nm by a template stripping method. • The Young's modulus of bismuth thin films is comparable to bulk bismuth.

  6. Bismuth Modified Carbon-Based Electrodes for the Determination of Selected Neonicotinoid Insecticides

    OpenAIRE

    Marko Rodić; Olga Vajdle; Valéria Guzsvány; Jasmina Zbiljić; Zsigmond Papp

    2011-01-01

    Two types of bismuth modified electrodes, a bismuth-film modified glassy carbon (BiF-GCE) and a bismuth bulk modified carbon paste, were applied for the determination of selected nitroguanidine neonicotinoid insecticides. The method based on an ex situ prepared BiF-GCE operated in the differential pulse voltammetric (DPV) mode was applied to determine clothianidin in the concentration range from 2.5 to 23 μg cm−3 with a relative standard deviation (RSD) not exceeding 1.5%. The tricresyl phosp...

  7. Structural and optical characterization of thermally evaporated bismuth and antimony films for photovoltaic applications

    Science.gov (United States)

    Srimathy, N.; Ruban Kumar, A.

    2016-05-01

    In this present study, the thin film of bismuth and antimony is coated by thermal evaporation system equipped with the inbuilt ultra high vacuum system. XRD analysis confirmed the rhombohedral structure of Bismuth and Antimony on the prepared film. The surface roughness and physical appearance is analyzed by Atomic force microscopy. The results of Raman Spectroscopy show the wave functions and the spectrum of electrons. The preparation technique and conditions strongly influence the crystalline structure and the phase composition of bismuth and antimony thin films. The electrical and optical properties for the prepared film are analyzed. The results show a great interest and promising applications in Photovoltaic devices.

  8. Exploiting Chemistry to Improve Performance of Screen-Printed, Bismuth Film Electrodes (SP-BiFE

    Directory of Open Access Journals (Sweden)

    Carlo Dossi

    2016-07-01

    Full Text Available Mercury substitution is a big issue in electroanalysis, and the search for a suitable, and less toxic, replacement is still under development. Of all the proposed alternatives, bismuth films appear to be the most viable solution, although they are still suffering some drawbacks, particularly the influence of deposition conditions and linearity at low concentrations. In this paper, the most promising strategies for bismuth film deposition on screen-printed electrodes (surface modifications, polymeric film deposition, insoluble salt precursors will be evaluated for trace metal analysis. Particular attention will be devoted to bismuth chemistry, aiming to rationalize their electroanalytic performance.

  9. Bismuth ferrite as low-loss switchable material for plasmonic waveguide modulator

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia; Zhukovsky, Sergei; Lavrinenko, Andrei

    2014-01-01

    We propose new designs of plasmonic modulators, which can beused for dynamic signal switching in photonic integrated circuits. We studyperformance of a plasmonic waveguide modulator with bismuth ferrite as atunable material. The bismuth ferrite core is sandwiched between metalplates (metal-insulator-metal...... modulation in both phase andamplitude control schemes. Due to high field confinement between themetal layers, existence of mode cut-offs for certain values of the corethickness, and near-zero material losses in bismuth ferrite, efficientmodulation performance is achieved. For the phase control scheme...

  10. Increased InAs quantum dot size and density using bismuth as a surfactant

    International Nuclear Information System (INIS)

    We have investigated the growth of self-assembled InAs quantum dots using bismuth as a surfactant to control the dot size and density. We find that the bismuth surfactant increases the quantum dot density, size, and uniformity, enabling the extension of the emission wavelength with increasing InAs deposition without a concomitant reduction in dot density. We show that these effects are due to bismuth acting as a reactive surfactant to kinetically suppress the surface adatom mobility. This mechanism for controlling quantum dot density and size has the potential to extend the operating wavelength and enhance the performance of various optoelectronic devices

  11. Functional Categories in Early Child German.

    Science.gov (United States)

    Clahsen, Harald; And Others

    1994-01-01

    Examined the representation of phrase structure in early child German through the investigation of longitudinal data from seven German-speaking toddlers with respect to verb placement, verb inflection, negation, /wh/ pronouns, and complementizers. It is argued that children construct phrase-structure trees in a gradual fashion, on the basis of…

  12. Massive job cuts threaten East German science

    CERN Multimedia

    Hamer, M

    1990-01-01

    German reunification could result in thousands of scientists losing their jobs. At the end of this year the East German state budget for science will run out. Scientists in the East are keen to find Western support to protect their research (1 page).

  13. The Role of German in Japan.

    Science.gov (United States)

    Sang, Juergen

    This historical overview of German studies in Japan, dating from the birth of modern Japan in the 1870's to the present time, includes commentary on the nature and scope of existing language programs. The importance of German idealism--reflected in the philosophy of Kant, Hegel, Schopenhauer, Nietzsche, and Marx--on Japanese culture is noted.…

  14. Teaching German for Musicians: A Practical Perspective.

    Science.gov (United States)

    Matthias, Bettina

    2003-01-01

    Explores the opportunities for teaching German for musicians and offers it as an approach to teaching beginning German in general. A short theoretical discussion of the impact of music on foreign language learning precedes the presentation of various teaching tools and ideas that map the territory in which musical foreign language teaching can…

  15. Semantic gender agreement: Dutch and German compared

    NARCIS (Netherlands)

    M. Kraaikamp

    2016-01-01

    This paper compares pronominal gender agreement in Dutch and German. Pronouns do not always agree with the gender of their antecedent: instead of agreeing with the lexical gender of the noun, they show semantic gender agreement. This is known to occur with human referents in both Dutch and German. I

  16. German Rap Music in the Classroom.

    Science.gov (United States)

    Schmidt, Johannes

    2003-01-01

    Provides background information on German rap artists and bands and discusses how to implement the music in various classroom situations at all levels. Highlights some of the available material on German rap music and provides information on how to locate rap texts, information, and other material via the Internet and other sources. (Author/VWL)

  17. German family policy at the crossroads

    DEFF Research Database (Denmark)

    Wüst, Miriam

    2009-01-01

    . Microsimulation helps to overcome these problems. It compares policy options - actual reforms or reform plans - simultaneously and provides a comparable measure: the disposable income of model families. This article uses a type-case approach to investigate recent reforms of the German parental leave benefit...... introduce a new concept of fairness and a focus on gender equality to German family policies....

  18. Facebook Used in a German Film Project

    Science.gov (United States)

    Leier, Vera

    2011-01-01

    Looking for a way to make German language study more relevant and to step out of the conventional classroom setting, I introduced Facebook (FB) as a learning platform to my intermediate German students at the University of Canterbury, New Zealand. The students took part in a film competition. A FB group was created and the films were uploaded. The…

  19. Language History for Teaching and Learning German

    Science.gov (United States)

    Lightfoot, Douglas

    2007-01-01

    This article presents information about the history of the German language and makes pertinent suggestions for teaching German as a Foreign Language. The reasoning for such an approach is presented, along with supportive new empirical data and a related professional directive. A selected survey of historical, explanatory points from the literature…

  20. The Dividend Policy of German Firms

    NARCIS (Netherlands)

    Andres, C.; Betzer, A.; Goergen, M.; Renneboog, L.D.R.

    2008-01-01

    German firms pay out a lower proportion of their cash flows, but a higher proportion of their published profits than UK and US firms. We estimate partial adjustment models and report two major findings. First, German firms base their dividend decisions on cash flows rather than published earnings as

  1. The Dividend Policy of German Firms

    NARCIS (Netherlands)

    Andres, C.; Betzer, A.; Goergen, M.; Renneboog, L.D.R.

    2008-01-01

    Abstract: German firms pay out a lower proportion of their cash flows, but a higher proportion of their published profits than UK and US firms. We estimate partial adjustment models and report two major findings. First, German firms base their dividend decisions on cash flows rather than published e

  2. When do German Firms Change their Dividends?

    NARCIS (Netherlands)

    Correia Da Silva, L.; Goergen, M.; Renneboog, L.D.R.

    2002-01-01

    Anecdotal evidence suggests that the dividend policy of German firms is more flexible than the one of their Anglo-American counterparts.This paper analyses the decision to change the dividend for a panel of 221 German firms from 1984 to 1994.The choice of the period of study is motivated by the fact

  3. The juridification of the German equalisation system

    NARCIS (Netherlands)

    Roberts, Edward

    1999-01-01

    This article is mainly about the contribution of the German Constitutional Court ('Bundesverfassungsgericht') in the implementation of the Financial Chapter of the German Constitution. The Court has defined in a legal way concepts which are also applied in the actual sharing of government income in

  4. Teuton vs Slav: The Great War Sinks Chicago's German "Kultur."

    Science.gov (United States)

    Holli, Melvin G.

    1981-01-01

    Describes the fervent political and cultural nationalism of German Americans in Chicago during World War I. Discusses how this nationalism, combined with ethnic conflict between Germans and Slavs, helped to sway public opinion against Chicago's German community. (GC)

  5. Swiss Themes in Three "Pluricentric" German Language Textbooks.

    Science.gov (United States)

    Boss, Bettina

    2003-01-01

    Examines three current textbooks for German as a foreign language with regard to their coverage of Switzerland as a German-speaking nation. Concludes by suggesting that pluricentric German language textbooks for beginners are rare. (Author/VWL)

  6. German versus Nordic Board Models

    DEFF Research Database (Denmark)

    Ringe, Georg

    2016-01-01

    Board structure is an important component of the individual governance of firms, and the appropriateness of the various models is one of the most debated issues in corporate governance today. A comparison of the Nordic and German approaches to the structure of corporate boards reveals stark...... conceptual differences, as emphasized by the 2014 Lekvall Report on the Nordic Corporate Governance Model. This article provides a conceptual comparison between the two approaches to board structure and confirms the fundamental divergence between both models. However, relying on a number of recent legal...... changes and developments in business practice, the article argues that board practices in the two systems effectively blur the structural distinction, and that board organization is converging in practice. It thereby contributes to the broader debates on functionality and comparative corporate law and...

  7. [The German Environmental Specimen Bank].

    Science.gov (United States)

    Schröter-Kermani, Christa; Gies, Andreas; Kolossa-Gehring, Marike

    2016-03-01

    The main objective of the German Environmental Specimen Bank (ESB) is the long-term storage of environmental and human samples under stable deep-freeze conditions for future research. The ESB is unique in providing a continuous historical record of environmental and human exposure to chemicals in Germany. ESB was started parallel to the development of the first German Chemicals Legislation in the late 1970s. In 1979, the ESB test operation began. After the Chemicals Law came into force in 1982, the ESB was established as a permanent facility in 1985. With the new European Chemicals Legislation, REACH, in 2007 responsibility for the safety of commercial chemicals and risk assessment was assigned to the industry. Since then, the ESB has become even more important in verifying the self-assessment of the industry, in evaluating the effectiveness of regulations, thus ensuring the protection of humans and the environment against adverse effects caused by exposure to chemicals. These objectives are pursued by the regular monitoring of contaminations and the assessment of temporal trends. Demonstrating the necessity of deriving exposure reduction measures, ESB results serve as key information for policy-makers. Information on preventing exposure to chemicals is available to the general public and to the public health services. The ESB is thus an important monitoring instrument of the Federal Ministry for the Environment, Nature Conservation, Building and Nuclear Safety. The Federal Environment Agency operates the ESB based on its own concepts, heads the scientific data evaluation and transfers results into the environmental policy arena and to the general public. PMID:26753867

  8. Conduction mechanism in bismuth silicate glasses containing titanium

    Energy Technology Data Exchange (ETDEWEB)

    Dult, Meenakshi; Kundu, R.S. [Department of Applied Physics, Guru Jambheshwar University of Science and Technology, Hisar 125001 (India); Murugavel, S. [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India); Punia, R., E-mail: rajeshpoonia13@gmail.com [Department of Applied Physics, Guru Jambheshwar University of Science and Technology, Hisar 125001 (India); Kishore, N. [Department of Applied Physics, Guru Jambheshwar University of Science and Technology, Hisar 125001 (India)

    2014-11-01

    Bismuth silicate glasses mixed with different concentrations of titanium dioxide having compositions xTiO{sub 2}–(60−x)Bi{sub 2}O{sub 3}–40SiO{sub 2} with x=0, 5, 10, 15 and 20 were prepared by the normal melt quench technique. The frequency dependence of the ac electrical conductivity of different compositions of titanium bismuth silicate glasses has been studied in the frequency range 10{sup −1} Hz to 10 MHz and in the temperature range 623–703 K. The temperature and frequency dependent conductivity is found to obey Jonscher's universal power law for all the compositions of titanium bismuth silicate glass system. The dc conductivity (σ{sub dc}), so called crossover frequency (ω{sub H}), and frequency exponent (s) have been estimated from the fitting of experimental data of ac conductivity with Jonscher's universal power law. Enthalpy to dissociate the cation from its original site next to a charge compensating center (H{sub f}) and enthalpy of migration (H{sub m}) have also been estimated. The conductivity data have been analyzed in terms of different theoretical models to determine the possible conduction mechanism. Analysis of the conductivity data and the frequency exponent shows that the correlated barrier hopping of electrons between Ti{sup 3+} and Ti{sup 4+} ions in the glasses is the most favorable mechanism for ac conduction. The temperature dependent dc conductivity has been analyzed in the framework of theoretical variable range hopping model (VRH) proposed by Mott which describe the hopping conduction in disordered semiconducting systems. The various polaron hopping parameters have also been deduced. Mott's VRH model is found to be in good agreement with experimental data and the values of inverse localization length of s-like wave function (α) obtained by this model with modifications suggested by Punia et al. are close to the ones reported for a number of oxide glasses.

  9. Shielding property of bismuth glass based on MCNP 5 and WINXCOM simulated calculation

    International Nuclear Information System (INIS)

    Background: Currently, lead glass is widely used as observation window, while lead is toxic heavy metal. Purpose: Non-toxic materials and their shielding effects are researched in order to find a new material to replace lead containing material. Methods: The mass attenuation coefficients of bismuth silicate glass were investigated with gamma-ray's energy at 0.662 MeV, 1.17 MeV and 1.33 MeV, respectively, by MCNP 5 (Monte Carlo) and WINXCOM program, and compared with those of the lead glass. Results: With attenuation factor K, shielding and mechanical properties taken into consideration bismuth glass containing 50% bismuth oxide might be selected as the right material. Dose rate distributions of water phantom were calculated with 2-cm and 10-cm thick glass, respectively, irradiated by 137Cs and 60Co in turn. Conclusion: Results show that the bismuth glass may replace lead glass for radiation shielding with appropriate energy. (authors)

  10. Three-component synthesis of amidoalkyl naphthols catalyzed by bismuth(Ⅲ) nitrate pentahydrate

    Institute of Scientific and Technical Information of China (English)

    Min Wang; Yan Liang; Ting Ting Zhang; Jing Jing Gao

    2012-01-01

    Bismuth(Ⅲ) nitrate pentahydrate catalyzed the three-component condensation of β-naphthol,aldehydes and amines/urea under solvent-free conditions to afford the corresponding amidoalkyl naphthols in excellent yields.

  11. Surface tension of liquid dilute solutions of lead-cesium and bismuth-cesium systems

    International Nuclear Information System (INIS)

    Method of the maximal pressure in a drop was used to measure the surface tension of 15 liquid dilute solutions of lead-cesium system in 0-0.214 at% concentration range and of 12 diluted solutions of bismuth-cesium system in 0-0.160 at.% cesium range from solidification temperature up to 500 dec C. It was found that cesium was characterized as surfactant in lead and bismuth melts. It was established that the temperature coefficient of surface tension changes sufficiently in maximally diluted solutions of alkali metals in bismuth and lead melts. Effect of sodium, potassium, rubidum and cesium on the value of surface tension of lead and bismuth was systematized. Growth of activity in sodium, potassium, rubidium and cesium series was noted

  12. Corrosion by liquid lead and lead-bismuth: experimental results review and analysis

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jinsuo [Los Alamos National Laboratory

    2008-01-01

    Liquid metal technologies for liquid lead and lead-bismuth alloy are under wide investigation and development for advanced nuclear energy systems and waste transmutation systems. Material corrosion is one of the main issues studied a lot recently in the development of the liquid metal technology. This study reviews corrosion by liquid lead and lead bismuth, including the corrosion mechanisms, corrosion inhibitor and the formation of the protective oxide layer. The available experimental data are analyzed by using a corrosion model in which the oxidation and scale removal are coupled. Based on the model, long-term behaviors of steels in liquid lead and lead-bismuth are predictable. This report provides information for the selection of structural materials for typical nuclear reactor coolant systems when selecting liquid lead or lead bismuth as heat transfer media.

  13. RECYCLING TECHNOLOGY INTO INDUSTRIAL TURNOVER OF BISMUTH AND MOLYBDENUM FROM DEAD CATALYST

    Directory of Open Access Journals (Sweden)

    O. S. Komarov

    2015-05-01

    Full Text Available The technology of separate extraction of bismuth and molybdenum from spent catalyst was presented and information on the effectiveness of its use in a composition of comprehensive modifier in the iron-carbon alloy was given.

  14. Standard triple, bismuth pectin quadruple and sequential therapies for Helicobacter pylori eradication

    OpenAIRE

    Gao, Xiao-Zhong; Qiao, Xiu-li; Song, Wen-chong; Wang, Xiao-Feng; Liu, Feng

    2010-01-01

    AIM: To compare the effectiveness of standard triple, bismuth pectin quadruple and sequential therapies for Helicobacter pylori (H. pylori) eradication in a randomized, double-blinded, comparative clinical trial in China.

  15. Azo dyes photobleaching and operando FTIR study of acetaldehyde photoinduced decomposition on bismuth doped titania

    Czech Academy of Sciences Publication Activity Database

    Henych, Jiří; Štengl, Václav; Mattsson, A.; Österlund, L.

    Thessaloniki : Aristotle University of Thessaloniki, 2014. s. 101. [European Meeting on Solar Chemistry and Photocatalysis: Environmental Applications (SPEA) /8./. 25.6.2014-28.6.2014, Thessaloniki] Institutional support: RVO:61388980 Keywords : bismuth doped titania Subject RIV: CA - Inorganic Chemistry

  16. A novel synthesis of perovskite bismuth ferrite nanoparticles

    Directory of Open Access Journals (Sweden)

    Alexandre Z. Simões

    2011-09-01

    Full Text Available Microwave assisted hydrothermal (MAH method was used to synthesize crystalline bismuth ferrite (BiFeO3 nanoparticles (BFO at temperature of 180°C with times ranging from 5 min to 1 h. For comparison, BFO powders were also crystallized by the soft chemistry route in a conventional furnace at a temperature of 850°C for 4 h. X-ray diffraction (XRD results verified the formation of perovskite BFO crystallites while infrared data showed no traces of carbonate. Field emission scanning microcopy (FE/SEM revealed a homogeneous size distribution of nanometric BFO powders. MAH method produced nanoparticles of 96% pure perovskite, with a size of 130 nm. These results are in agreement with Raman scattering values which show that the MAH synthesis route is rapid and cost effective. This method could be used as an alternative to other chemical methods in order to obtain BFO nanoparticles.

  17. Vibrational spectra and structure of bismuth based quaternary glasses

    International Nuclear Information System (INIS)

    Quaternary bismuthate glasses containing Li2O, ZnO and B2O3 have been prepared by melt quench technique and studied by density, DSC, IR and Raman spectroscopy. Raman and infrared spectroscopy have been employed to investigate the (75 - x)Bi2O3-xLi2O-10ZnO-15B2O3 glasses in order to obtain information about the competitive role of Bi2O3 and B2O3 in the formation of glass network. The increase of Bi2O3 content causes a progressive conversion of three- to four-fold coordinated boron. IR and Raman spectra show that these glasses are made up of [BiO3] pyramidal and [BiO6] octahedral units. The formation of Zn in tetrahedral coordination was observed

  18. Evaporation of mercury impurity from liquid lead–bismuth eutectic

    International Nuclear Information System (INIS)

    The equilibrium evaporation of mercury from dilute solutions in liquid lead–bismuth eutectic (LBE) was studied in argon atmosphere. Mercury present as impurity in LBE was evaporated and detected by atomic fluorescence spectroscopy. A method which could accurately simulate the experimental data was developed. Coefficients of the Henry constant temperature correlation for mercury dissolved in LBE were determined. Experiments with samples from several different batches of LBE revealed that mercury at mole fractions between 10−6 and 10−12 and temperatures between 150 and 350 °C evaporated from liquid LBE close to ideal behavior. Evaporation of mercury from solid LBE on the other hand was unexpectedly high. These results are important for safety evaluations of LBE based spallation targets and accelerator driven systems

  19. High power and compact switchable bismuth based multiwavelength fiber laser

    International Nuclear Information System (INIS)

    A compact switchable multiwavelength fibre laser (SWFL) is proposed and demonstrated using a bismuth based erbium doped fibre amplifier (Bi-EDFA) and a Sagnac loop mirror (SLM) in a ring cavity. The proposed compact SWFL can generate up to 6 switchable wavelengths with an average peak power of 11 dBm and also shows good stability over time with a high side mode signal ratio (SMSR) of 40 dB that negates minor fluctuations in the laser output. The Bi-EDF based gain medium gives the SWFL a large usable bandwidth of up to 80 nm, and it is expected that this will allow the SWFL to be used as a tunable laser source for high power applications to meet increasing demand

  20. Structural investigation of Zn doped sodium bismuth borate glasses

    Science.gov (United States)

    Bhatia, V.; Kumar, D.; Singh, D.; Singh, S. P.

    2016-05-01

    A series of Bismuth Borate Oxide Glass samples with composition x(ZnO):(15-x)Na2O:15Bi2O3:70B2O3 (variation in x is from 6 to 12 mole %) have been prepared by conventional melt quenching technique. All the chemicals used were of Analytical Grade. In order to verify the amorphous nature of the prepared samples the X-Ray Diffraction (XRD) was done. The physical and structural properties have been explored by using the techniques such as density, molar volume and FTIR in order to understand the effect of alkali and transition metal ions on the structure of these glasses. The results obtained by these techniques are in good agreement to one another and with literature as well. With the increase in the content of ZnO, the increase in density and some variations in structural coordination (ratio of BO3 & BO4 structural units) have been observed.

  1. Compatibility of structural materials with liquid bismuth, lead, and mercury

    Energy Technology Data Exchange (ETDEWEB)

    Weeks, J.R. [Brookhaven National Lab., Upton, NY (United States)

    1996-06-01

    During the 1950s and 1960s, a substantial program existed at Brookhaven National Laboratory as part of the Liquid Metal Fuel reactor program on the compatibility of bismuth, lead, and their alloys with structural materials. Subsequently, compatibility investigations of mercury with structural materials were performed in support of development of Rankine cycle mercury turbines for nuclear applications. The present talk will review present understanding of the corrosion/mass-transfer reactions of structural materials with these liquid metal coolants. Topics to be discussed include the basic solubility relationships of iron, chromium, nickel, and refractory metals in these liquid metals, the results of inhibition studies, the role of oxygen on the corrosion processes, and specialized topics such as cavitation-corrosion and liquid metal embrittlement. Emphasis will be placed on utilizing the understanding gained in this earlier work on the development of heavy liquid metal targets in spallation neutron sources.

  2. Formic Acid Oxidation at Platinum-Bismuth Clusters

    DEFF Research Database (Denmark)

    Lovic, J. D.; Stevanovic, S. I.; Tripkovic, D. V.; Tripkovic, Vladimir; Stevanovic, R. M.; Popovic, K. Dj.; Jovanovic, V. M.

    2014-01-01

    Formic acid oxidation was studied on platinum-bismuth deposits on glassy carbon (GC) substrate. The catalysts of equimolar ratio were prepared by potentiostatic deposition using chronocoulometry. Bimetallic structures obtained by two-step process, comprising deposition of Bi followed by deposition...... dissolution, deposits were subjected to electrochemical oxidation, in the relevant potential range and supporting electrolyte, prior to use as catalysts for HCOOH oxidation. Anodic striping charges indicated that along oxidation procedure most of deposited Bi was oxidized. ICP mass spectroscopy analysis of...... latter. Catalysts prepared in this way exhibit about 10 times higher activity for formic acid oxidation in comparison to pure Pt, as revealed both by potentiodynamic and quasy-potentiostatic measurements. This high activity is the result of well-balanced ensemble effect induced by Bi-oxide species...

  3. Ni-rich precipitates in a lead bismuth eutectic loop

    Science.gov (United States)

    Kikuchi, K.; Saito, S.; Hamaguchi, D.; Tezuka, M.

    2010-03-01

    Solidified LBE was sampled from the specimens, electro-magnetic pump, filter, drain valve and oxygen sensor at the JAEA Lead Bismuth Loop-1 (JLBL-1) where the structural material was made of SS316. The concentration of Ni, Fe and Cr in LBE were analyzed by the Inductive Coupled Plasma atomic emission spectrometer. It was concluded that the solution of Ni into LBE was not saturated although the concentration of Fe and Cr almost achieved to the values in the literature. A needle-type structure appeared on the surface of solidified LBE inside the tube specimens. It was found to be Ni-rich precipitates by X-ray analyses (Field Emission Scanning Electron Microscope, FE-SEM). LBE samples collected from a circulating loop after discharging did not show the amount of impurities equivalent to the LBE bulk property.

  4. Evaporation of mercury impurity from liquid lead–bismuth eutectic

    Energy Technology Data Exchange (ETDEWEB)

    Aerts, A., E-mail: aaertsl@sckcen.be [SCK-CEN (Belgian Nuclear Research Centre), Boeretang 200, 2400 Mol (Belgium); Danaci, S. [SCK-CEN (Belgian Nuclear Research Centre), Boeretang 200, 2400 Mol (Belgium); Gonzalez Prieto, B. [SCK-CEN (Belgian Nuclear Research Centre), Boeretang 200, 2400 Mol (Belgium); Centre for Surface Chemistry and Catalysis, KU Leuven, Kasteelpark Arenberg 23, 3001 Heverlee (Belgium); Van den Bosch, J. [SCK-CEN (Belgian Nuclear Research Centre), Boeretang 200, 2400 Mol (Belgium); Neuhausen, J. [Laboratory for Radio- and Environmental Chemistry, Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland)

    2014-05-01

    The equilibrium evaporation of mercury from dilute solutions in liquid lead–bismuth eutectic (LBE) was studied in argon atmosphere. Mercury present as impurity in LBE was evaporated and detected by atomic fluorescence spectroscopy. A method which could accurately simulate the experimental data was developed. Coefficients of the Henry constant temperature correlation for mercury dissolved in LBE were determined. Experiments with samples from several different batches of LBE revealed that mercury at mole fractions between 10{sup −6} and 10{sup −12} and temperatures between 150 and 350 °C evaporated from liquid LBE close to ideal behavior. Evaporation of mercury from solid LBE on the other hand was unexpectedly high. These results are important for safety evaluations of LBE based spallation targets and accelerator driven systems.

  5. Process dependent thermoelectric properties of EDTA assisted bismuth telluride

    Science.gov (United States)

    Kulsi, Chiranjit; Kargupta, Kajari; Banerjee, Dipali

    2016-04-01

    Comparison between the structure and thermoelectric properties of EDTA (Ethylene-diamine-tetra-acetic acid) assisted bismuth telluride prepared by electrochemical deposition and hydrothermal route is reported in the present work. The prepared samples have been structurally characterized by high resolution X-ray diffraction spectra (HRXRD), field emission scanning electron microscopy (FESEM) and high resolution transmission electron microscopic images (HRTEM). Crystallite size and strain have been determined from Williamson-Hall plot of XRD which is in conformity with TEM images. Measurement of transport properties show sample in the pellet form (S1) prepared via hydrothermal route has higher value of thermoelectric power (S) than the electrodeposited film (S2). But due to a substantial increase in the electrical conductivity (σ) of the film (S2) over the pellet (S1), the power factor and the figure of merit is higher for sample S2 than the sample S1 at room temperature.

  6. Enhanced multiferroic properties of Pr doped bismuth ferrite ceramics

    International Nuclear Information System (INIS)

    Pr modified Bi0.9-xLa0.1PrxFeO3 (BLPFO-x, x = 0, 0.1 and 0.2) ceramics were prepared by solid state reaction using oxide reagents and a detailed multiferroic properties is reported. X-ray analysis shows the formation of a bismuth ferrite rhombohedral phase. Pr doping significantly increases the resistivity and leads to a successful observation of electrical polarization hysteresis loops. All the samples have been found to possess a spontaneous magnetic moment at room temperature which increases further at low temperatures. The strong dependence of remnant polarization and dielectric constant on the strength of magnetic field is a direct evidence of magnetoelectric coupling in BLPFO ceramics. (author)

  7. Scanning tunneling microscopy of the cleavage surface of bismuth crystals

    International Nuclear Information System (INIS)

    The results of in situ studies of the surface structure of the cleavages of bismuth crystals by the method of scanning tunneling microscopy are presented. It is established that cleavage 'opens' the (111) surface with atomically smooth terraces of diatomic steps whose heights are equal to 0.4 nm or a multiple of this value. If the cleavage is made at room temperature, the boundaries of the terraces are usually curved and diffuse owing to the thermal motion with the activation energy of ∼700 K. The cleavage at liquid nitrogen or helium temperatures provides the formation of straight boundaries along the atomic rows on the surface. Twin interlayers of the quantized width of ∼7 nm are revealed. This width value indicates that the atomic planes on both sides of such interlayers intergrow with the interlayer planes inclined to them at a small angle

  8. Toxicity of Volatile Methylated Species of Bismuth, Arsenic, Tin, and Mercury in Mammalian Cells In Vitro

    OpenAIRE

    Rettenmeier, A W; Zimmermann, U.; Richard, J.; R. A. Diaz-Bone; Hippler, J; U. von Recklinghausen; Dopp, E.; Hirner, A. V.

    2011-01-01

    The biochemical transformation of mercury, tin, arsenic and bismuth through formation of volatile alkylated species performs a fundamental role in determining the environmental processing of these elements. While the toxicity of inorganic forms of most of these compounds are well documented (e.g., arsenic, mercury) and some of them are of relatively low toxicity (e.g., tin, bismuth), the more lipid-soluble organometals can be highly toxic. In the present study we investigated the cyto- and ge...

  9. Determination of vanadium concentration in bismuth titanate monocrystals and its relation to optical properties and photoconductivity

    International Nuclear Information System (INIS)

    Using Czochralski method optically perfect bismuth titanate crytals doped by vanadium (0.14-0.46 mass.%) are prepared. A technique of vanadium concentration measurement by Raman spectra is developed. Photoconductivity and optical properties of tehse monocrystals are studied. It is shown that in λ > 530 nm wave range photoconductivity of doped monocrystals is by 1-2 order higher than in pure bismuth titanate monocrystal

  10. In vitro synergistic activity between bismuth subcitrate and various antimicrobial agents against Campylobacter pyloridis (C. pylori).

    OpenAIRE

    Van Caekenberghe, D L; Breyssens, J

    1987-01-01

    The in vitro interactions between bismuth subcitrate and a variety of antimicrobial agents against 12 Campylobacter pyloridis (C. pylori) isolates were studied by the agar dilution checkerboard technique. The combination of bismuth subcitrate with the older quinolone, oxolinic acid, produced synergistic activity against all strains. This observation, however, could not be extended to the (aryl) fluoroquinolones, norfloxacin, ofloxacin, and difloxacin, since synergy was rare or absent when bis...

  11. Intermetallic growth at the interface between copper and bismuth-tin solder

    OpenAIRE

    Vollweiler, Fred O. P.

    1993-01-01

    Approved for public release; distribution is unlimited. Tin-bismuth alloys have been proposed as alternatives to lead containing solders for interconnection and packaging applications. Consequently, the interface between copper metallizations and bismuth-tin solders needs to be evaluated with respect to brittle intermetallic formation. In the binary Bi-Sn alloys both the Cu6Sn5 and Cu3Sn intermetallic phases were found at the Cu/ solder interface after exposure at 250 deg C, 300 deg C, and...

  12. Shock compression and adiabatic decompression of a dense bismuth plasma at extreme thermal energy densities

    International Nuclear Information System (INIS)

    Experimental results on the shock-wave compression of solid and porous bismuth samples at pressures over the range 0.4-6 Mbar are reported. The course of the supercritical decompression isentropes between a highly compressed condensed state and a low-density plasma has been determined. The experimental results are used to write a thermodynamic description of the high-energy states of a dense bismuth plasma. 11 references

  13. Direct Electrochemical Synthesis of Bismuth(III) Phenoxides and their Coordination Compounds

    OpenAIRE

    Harpreet Kaur; Baljit Singh

    2012-01-01

    Bismuth(III) phenoxides have been synthesized by electrochemical reactions of 1-naphthol, 2-naphthol, 4-aminophenol, 2-nitrophenol, 4-nitrophenol, 2-hydroxybenzoic acid, p-cresol, phenol, resorcinol, 2-tert-butylphenol and 2-tert-butyl-4-methoxyphenol at sacrificial bismuth anode and inert platinum cathode using tetrabutylammonium chloride as supporting electrolyte. The coordination compounds of these phenols with 1, 10-phenanthroline and 2, 2ʼ-bipyridyl have also been synthesized electrochem...

  14. Study of bismuth minerals belonging to the mineralogical collection from the National Museum

    International Nuclear Information System (INIS)

    With the purpose of searching the presence of Tellurium minerals in the Ouro Preto-Mariana country, Minas Gerais State, and considering the existence of a great number of minerals in which this element come across allied with Bismuth, samples of the mineralogical collection of the Museu Nacional, proceeding that region and classified as Bismuth minerals were studied by X-ray fluorescence analysis and diffractometric analysis. In this report the results of this research are presented. (Author)

  15. Lead-bismuth eutectic corrosion behaviors of ferritic/martensitic steels in low oxygen concentration environment

    OpenAIRE

    Liu, Jian; Shi, Quanqiang; Luan, He; Yan, Wei; Sha, Wei; Wang, Wei; Shan, Yiyin; Yang, Ke

    2015-01-01

    In order to investigate the compatibility of candidate structural materials with liquid metals, two kinds of ferritic/martensitic steels were chosen to contact with lead–bismuth eutectic in sealed quartz–glass tubes. The corrosion exposures were for 500 and 3000 h. Results showed that the oxidation layer and carbide dissolution layer on the two steels grew with contact time under oxygen unsaturated condition. Short-term corrosion behavior of a newly developed steel showed better lead–bismuth ...

  16. Comparison of radiation shielding ratios of nano-sized bismuth trioxide and molybdenum

    Science.gov (United States)

    Cho, J. H.; Kim, M. S.; Rhim, J. D.

    2015-07-01

    In this study, radiation shielding fibers using non-hazardous nano-sized bismuth trioxide and molybdenum instead of lead were developed and evaluated. Among the elements with high densities and atomic numbers, non-hazardous elements such as bismuth trioxide and molybdenum were chosen as a shielding element. Then, bismuth trioxide (Bi2O3) with average particle size 1-500 µm was ball milled for 10 min to produce a powdered form of nanoparticles with average particle size of 10-100 nm. Bismuth trioxide nanoparticles were dispersed to make a colloidal suspension, followed by spreading and hardening onto one or two sides of fabric, to create the radiation shielding fabric. The thicknesses of the shielding sheets using nano-sized bismuth and molybdenum were 0.4 and 0.7 mm. According to the lead equivalent test of X-ray shielding products suggested by KS, the equivalent dose was measured, followed by calculation of the shielding rate. The shielding rate of bismuth with 0.4 mm thickness and at 50 kVp was 90.5%, which is comparable to lead of 0.082 mm thickness. The shielding rate of molybdenum was 51.89%%, which is comparable to lead of 0.034 mm. At a thickness of 0.7 mm, the shielding rate of bismuth was 98.73%, equivalent to 0.101 mm Pb, whereas the shielding rate of molybdenum was 74.68%, equivalent to 0.045 mm Pb. In conclusion, the radiation shielding fibers using nano-sized bismuth developed in this study are capable of reducing radiation exposure by X-ray and its low-dose scatter ray.

  17. Ferroelectric thin film bismuth titanate prepared from acetate precursors

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yanxia; Hoelzer, D.T.; Schulze, W.A. [Alfred Univ., NY (United States); Tuttle, B.A.; Potter, B.G. [Sandia National Labs., Albuquerque, NM (United States)

    1994-10-01

    Bismuth titanate (Bi{sub 4}Ti{sub 3}O{sub 12}) thin films were fabricated by spin coat deposition followed by rapid thermal processing (RTP). Acetate derived solutions for deposition were synthesized by blending bismuth acetate in aqueous acetic acid and then adding titanium acetate. A series of electrically insulating, semiconducting and conducting substrates were evaluated for Bi{sub 4}Ti{sub 3}O{sub 12} film deposition. While X-ray diffraction and TEM analyses indicated that the initial perovskite crystallization temperature was 500{degrees}C or less for these Bi{sub 4}Ti{sub 3}O{sub 12} films, a 700{degrees}C crystallization treatment was used to obtain single phase perovskite films. Bi{sub 4}Ti{sub 3}O{sub 12} film crystallographic orientation was shown to depend on three factors: substrate surface morphology, the number of coating layers and thermal processing. While preferred c-direction orientation was observed for Bi{sub 4}Ti{sub 3}O{sub 12} films deposited on silver foil substrates, preferred a-direction orientation was obtained for films deposited on both Si and Pt coated Si wafers. The films were dense, smooth, crack free, and had grain sizes ranging from 20 nm to 100 nm. Film thickness and refractive index were determined using a combination of ellipsometry, waveguide refractometry and TEM measurements. Both low field dielectric and ferroelectric properties were measured for an 800 nm thick film deposited on a Pt coated MgO substrate. A remanent polarization of 38 {mu}C/cm{sup 2} and a coercive field of 98 kV/cm were measured for this film that was crystallized at 700{degrees}C.

  18. Polonium problem in lead-bismuth flow target

    Energy Technology Data Exchange (ETDEWEB)

    Pankratov, D.V.; Yefimov, E.I.; Bugreev, M.I. [State Scientific Centre of Russian Federation-Institute of Physics and Power Engineering, Obninsk (Russian Federation)

    1996-06-01

    Alpha-active polonium nuclides Po198 - Po210 are formed in a lead-bismuth target as results of reactions Bi{sup 209}(n,{gamma})Bi{sup 210} {yields} Po{sup 210}, Bi{sup 209}(p,xn)Po{sup 210} {yields} Po{sup 210 {minus} x} (x = 1-12), Pb{sup 208}({alpha},xn) {yields} Po{sup 210 {minus} x + 2} (x = 2-14). The most important nuclides are Po-210 (T{sub {1/2}}=138.4 day), Po-209 (T{sub {1/2}}=102 years) and Po-208 (T{sub {1/2}}=2.9 years). Polonium activity of the circuit for SINQ - conditions is about 15,000 Ci after 1-year operation. Polonium radiation hazard is connected with its output from the coolant and formation of aerosol and surface alpha-activity after the circuit break-down for repair works or in accidents. One of the important issues of polonium removal system creation is containing and storing polonium removed. Its storage in solidified alkaline is not expedient because of secondary neutron formation as a result of ({alpha},n) - reaction on oxygen and sodium nucleus. The estimations carried out demonstrated that by polonium concentration {approx} 100 Ci/l neutron current on the container surface can reach {approx} 10{sup 4}n/(cm{sup 2}s). Concentration and storage of polonium in solidified lead-bisumth seems the most convenient. The calculations demonstrated that in a 100 l container 50,000 Ci of polonium can be stored (as much as 3 times more than 1-year polonium product in SINQ-conditions) under temperature in the container less than melting point of lead bismuth (the wall temperature is about 100{degrees}C).

  19. [The boycott against German scientists and the German language after World War I].

    Science.gov (United States)

    Reinbothe, R

    2013-12-01

    After the First World War, the Allied academies of sciences staged a boycott against German scientists and the German language. The objective of the boycott was to prevent the re-establishment of the prewar dominance of German scientists, the German language and German publications in the area of international scientific cooperation. Therefore the Allies excluded German scientists and the German language from international associations, congresses and publications, while they created new international scientific organizations under their leadership. Medical associations and congresses were also affected, e. g. congresses on surgery, ophthalmology and tuberculosis. Allied physicians replaced the "International Anti-Tuberculosis Association" founded in Berlin in 1902 with the "Union Internationale contre la Tuberculose"/"International Union against Tuberculosis", founded in Paris in 1920. Only French and English were used as the official languages of the new scientific organizations, just as in the League of Nations. The boycott was based on the fact that the German scientists had denied German war guilt and war crimes and glorified German militarism in a manifesto "To The Civilized World!" in 1914. The boycott first started in 1919 and had to be abolished in 1926, when Germany became a member of the League of Nations. Many German and foreign physicians as well as other scientists protested against the boycott. Some German scientists and institutions even staged a counter-boycott impeding the resumption of international collaboration. The boycott entailed an enduring decline of German as an international scientific language. After the Second World War scientists of the victorious Western Powers implemented a complete reorganization of the international scientific arena, based on the same organizational structures and language restrictions they had built up in 1919/1920. At the same time scientists from the U.S.A. staged an active language and publication policy, in

  20. Nano sized bismuth oxy chloride by metal organic chemical vapour deposition

    Energy Technology Data Exchange (ETDEWEB)

    Jagdale, Pravin, E-mail: pravin.jagdale@polito.it [Department of Applied Science and Technology (DISAT), Politecnico di Torino, 10129 (Italy); Castellino, Micaela [Center for Space Human Robotics, Istituto Italiano di Tecnologia, Corso Trento 21, 10129 Torino (Italy); Marrec, Françoise [Laboratory of Condensed Matter Physics, University of Picardie Jules Verne (UPJV), Amiens 80039 (France); Rodil, Sandra E. [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexicom (UNAM), Mexico D.F. 04510 (Mexico); Tagliaferro, Alberto [Department of Applied Science and Technology (DISAT), Politecnico di Torino, 10129 (Italy)

    2014-06-01

    Metal organic chemical vapour deposition (MOCVD) method was used to prepare thin films of bismuth based nano particles starting from bismuth salts. Nano sized bismuth oxy chloride (BiOCl) crystals were synthesized from solution containing bismuth chloride (BiCl{sub 3}) in acetone (CH{sub 3}-CO-CH{sub 3}). Self-assembly of nano sized BiOCl crystals were observed on the surface of silicon, fused silica, copper, carbon nanotubes and aluminium substrates. Various synthesis parameters and their significant impact onto the formation of self-assembled nano-crystalline BiOCl were investigated. BiOCl nano particles were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy and Micro-Raman spectroscopy. These analyses confirm that bismuth nanometer-sized crystal structures showing a single tetragonal phase were indeed bismuth oxy chloride (BiOCl) square platelets 18–250 nm thick and a few micrometres wide.

  1. Adverse events with bismuth salts for Helicobacter pylori eradication:Systematic review and meta-analysis

    Institute of Scientific and Technical Information of China (English)

    Alexander C Ford; Peter Malfertheiner; Monique Giguére; José Santana; Mostafizur Khan; Paul Moayyedi

    2008-01-01

    AIM:To assess the safety of bismuth used in Helicobacter pylori (H pylori) eradication therapy regimens.METHODS:We conducted a systematic review and meta-analysis.MEDLINE and EMBASE were searched (up to October 2007) to identify randomised controlled trials comparing bismuth with placebo or no treatment,or bismuth salts in combination with antibiotics as part of eradication therapy with the same dose and duration of antibiotics alone or,in combination,with acid suppression.Total numbers of adverse events were recorded.Data were pooled and expressed as relative risks with 95% confidence intervals (CI).RESULTS:We identified 35 randomised controlled trials containing 4763 patients.There were no serious adverse events occurring with bismuth therapy.There was no statistically significant difference detected in total adverse events with bismuth [relative risk (RR)=1.01;95% CI:0.87-1.16],specific individual adverse events,with the exception of dark stools (RR = 5.06;95% CI:1.59-16.12),or adverse events leading to withdrawal of therapy (RR = 0.86;95% CI:0.54-1.37).CONCLUSION:Bismuth for the treatment of H pylori is safe and well-tolerated.The only adverse event occurring significantly more commonly was dark stools.

  2. German energy market 2014; Deutscher Energiemarkt 2014

    Energy Technology Data Exchange (ETDEWEB)

    Schiffer, Hans-Wilhelm [World Energy Council, London (United Kingdom). World Energy Resources; Weltenergierat - Deutschland, Berlin (Germany). Arbeitsgruppe ' Energie fuer Deutschland'

    2015-03-15

    In 2014 the German government's primary goal of engaging German power suppliers to step up their production of renewable energy while speeding up energy efficiency improvement measures continued to dominate the debate. The present article provides an updated overview of the German energy market. Following on from last year's edition it gives a condensed synopsis of key indicators of the energy economy. Besides summarising general facts about the energy mix it goes into detail about the following individual energy resources: crude oil, natural gas, brown coal, hard coal, nuclear energy and renewable energies. It also explains current price trends in both the international and domestic markets.

  3. German innovation initiative for nanotechnology

    International Nuclear Information System (INIS)

    In many areas of nanotechnology, Germany can count on a good knowledge basis due to its diverse activities in nanosciences. This knowledge basis, when paired with the production and sales structures needed for implementation and the internationally renowned German talent for system integration, should consequently lead to success in the marketplace. And this is exactly the field of application for the innovation initiative 'Nanotechnologie erobert Maerkte' (nanotechnology conquers markets) and for the new BMBF strategy in support of nanotechnology. Until now, aspects of nanotechnology have been advanced within the confines of their respective technical subject areas. However, the primary aim of incorporating them into an overall national strategy is to build on Germany's well-developed and internationally competitive research in science and technology to tap the potential of Germany's important industrial sectors for the application of nanotechnology through joint research projects (leading-edge innovations) that strategically target the value-added chain. This development is to be supported by government education policy to remedy a threatening shortage of skilled professionals. To realize that goal, forward-looking political policymaking must become oriented to a uniform concept of innovation, one that takes into consideration all facets of new technological advances that can contribute to a new culture of innovation in Germany. And that includes education and research policy as well as a climate that encourages and supports innovation in science, business and society

  4. The German power supply situation

    International Nuclear Information System (INIS)

    The first key statement of this paper runs like this: The situation of power supply in Germany basically is good. However, two qualifications should be added: The current situation is still good. Power outages as a consequence of power plant failures of the kind experienced in other countries must not be expected to occur in Germany. German utilities work hard to offer this assurance also for the future. This is where politics comes in with the need to guarantee reliable framework conditions. After deregulation of the electricity market, reregulation resulting from government interventions is becoming potentially more and more problematic. Energy issues remain at the top of the political agenda, e.g. with the amendment to the Power Economy Act. This is a matter involving a variety of questions and projects on the part of legislators which require delicate handling because, in addition to the prices to be paid by consumers, they also involve as the most important factor the continuity of supply. Nuclear power today covers a major part of our baseload supply, in addition to lignite and hard coal which are used mainly in the medium-load range. Supported by the findings of recent studies, such as the dena Study, the Prognos and EWI Energy Report, the problem is how to replace this share reliably, in a way protecting the climate and economically viable, in line with the political conditions stipulating residual electricity outputs of nuclear power plants. Other countries can be seen to pursue different policies in using nuclear power. (orig.)

  5. German Grid Initiative D-Grid

    OpenAIRE

    2007-01-01

    This publication gives a detailed overview of the current state of the German Grid Initative with emphasis on the long-term strategic grid research and development activities for academia and industry.

  6. A German format for pupils’ training

    CERN Multimedia

    Antonella Del Rosso

    2012-01-01

    Every year CERN welcomes thousands of pupils from schools worldwide for a half-day visit to the Laboratory. However, since 2011 about ten selected students from Germany have been given the opportunity to experience CERN in much greater depth. They are fully sponsored by the German Ministry of Education and supported by an organising structure at TU Dresden - the Dresden University of Technology - led by Michael Kobel. It’s an investment that's paying off in Germany.   The German teachers who participated in the “Netzwerk Teilchenwelt” project, at CERN last week. “Netzwerk Teilchenwelt” is a project that involves 23 German universities, the DESY Laboratory, several schools and, of course, CERN. Launched in 2010 with a contribution from the German Ministry for Science and Research of about 1 million euros over three years, the project has so far involved over 4,000 students and 500 teachers. “Thanks to this project, both pupils...

  7. The German Model of Bilingual Education.

    Science.gov (United States)

    Masch, Nando

    1993-01-01

    The German model of bilingual education is described in terms of its history, syllabus, rationale, and aims and objectives. The essential features of the model are contrasted with other forms of bilingual education. (Contains 23 references.) (JL)

  8. Crossing the Lexicon: Anglicisms in the German Hip Hop Community

    Science.gov (United States)

    Garley, Matthew E.

    2012-01-01

    The influence of English on German has been an ongoing subject of intense popular and academic interest in the German sphere. In order to better understand this language contact situation, this research project investigates anglicisms--instances of English language material in a German language context--in the German hip hop community, where the…

  9. African Americans Who Teach German Language and Culture.

    Science.gov (United States)

    Fikes, Robert Jr.

    2001-01-01

    A large number of black scholars have pursued advanced degrees in the German language, history, and culture. Describes the history of African American interest in the German language and culture, highlighting various black scholars who have studied German over the years. Presents data on African Americans in German graduate programs and examines…

  10. Explaining Institutional Change in German Capitalism

    OpenAIRE

    Glassmann Ulrich

    2009-01-01

    This article explains why actors in the German political economy supported incremental change in institutional sectors which the advocates of the varieties of capitalism approach identify as being crucial for the efficient delivery of innovation measures. What causes these gradual shifts by which German capitalism departs from the Rhenish equilibrium? My central thesis is that incremental change has created resources of flexibility which help to sustain strong and traditional industries. In t...

  11. A German Perspective on Security Research

    Science.gov (United States)

    Thoma, Klaus; Hiller, Daniel; Leismann, Tobias; Drees, Birgit

    Prior to 2007, there was no coherent federal approach to conceptualise and fund security research in Germany. This changed with the initiation of the national program for civil security research, managed by the German Ministry for Education and Research (BMBF). Over the course of only four years a continuous build-up of national capacities on civil security was established to better protect German citizens, commodities and infrastructures against terrorism, organised crime and the effects of man-made and natural disasters.

  12. Recent Developments in German Corporate Governance

    OpenAIRE

    Goergen, M.; Manjon, M.C.; Renneboog, L.D.R.

    2004-01-01

    This paper provides an overview of the German corporate governance system. We review the governance role of large shareholders, creditors, the product market and the supervisory board. We also discuss the importance of mergers and acquisitions, the market in block trades, and the lack of a hostile takeover market. Given that Germany is often referred to as a bank-based economy, we pay particular attention to the role of the universal banks (Hausbanken). We show that the German system is chara...

  13. The Great War and German Memory

    DEFF Research Database (Denmark)

    Leese, Peter

    2012-01-01

    Review essay on Jason Crouthamel, The Great War and German Memory. Society, Politics and Psychological Trauma, 1914-18 (2009) and Anton Kaes, Shell Shock Cinema: Weimar Culture and the Wounds of War (2009)......Review essay on Jason Crouthamel, The Great War and German Memory. Society, Politics and Psychological Trauma, 1914-18 (2009) and Anton Kaes, Shell Shock Cinema: Weimar Culture and the Wounds of War (2009)...

  14. Religious freedom and the German circumcision debate

    OpenAIRE

    Marianne Heimbach-Steins

    2013-01-01

    In May 2012, a German court in Cologne ruled that circumcising young boys represents grievous bodily harm. This decision, which touched upon the questions of freedom of religious practice, identity and children’s rights, was condemned by Jewish and Muslim representatives in Germany, but it was also widely and controversially debated by civil society and politicians. The German Parliament recently passed legislation protecting circumcision as a religious practice, but the debate is likely to c...

  15. Price volatility on the German Agricultural Markets

    OpenAIRE

    Ledebur, Oliver von; Schmitz, Jochen

    2012-01-01

    In this contribution, the development of price volatility on German agricultural markets is analyzed. We quantify the degree of price volatility for selected German agricultural markets and determine how it evolves over time and search for policy driven structural changes in volatility levels measured by the historical volatility. Based on annualised historical volatilities t test were performed to identify if the change in the volatility levels show any relationship to the process of reform ...

  16. German Environmental Law; Doitsu no kankyoho

    Energy Technology Data Exchange (ETDEWEB)

    Abe, Yasutaka [Kobe University, Hyogo (Japan). Faculty of Law

    1999-12-16

    The German environmental law scheme, one of the top runners in the world, has a lot of policy suggestions for developing a more reasonable and rational regulatory institution. Paying careful attention to the differences between German and Japanese systems, this research makes a comprehensive analysis of the German law from a comparative perspective. Our research method is as follows : a library research of the German environmental law, questionnaires to German regulators and scholars, interviews with some of them in Germany. Summing up some findings, the economic incentive, as a regulatory tool, is considered to be 'the last resort', when the 'command-and-control' approach turns out a failure ; the regulatory agency, not a developer, is charged with environmental impact assessment because of its 'neutrality' and 'reliability'. Further research on this field is to be conducted in coming few years, which is followed by a publication of 'The German Environmental Law', the first academic achievement in Japan. (author)

  17. Accent, Intelligibility, and the Role of the Listener: Perceptions of English-Accented German by Native German Speakers

    Science.gov (United States)

    Hayes-Harb, Rachel; Watzinger-Tharp, Johanna

    2012-01-01

    We explore the relationship between accentedness and intelligibility, and investigate how listeners' beliefs about nonnative speech interact with their accentedness and intelligibility judgments. Native German speakers and native English learners of German produced German sentences, which were presented to 12 native German speakers in accentedness…

  18. Capturing the Zeitgeist. Native German Loanwords in English

    OpenAIRE

    Þorsteinn Hjaltason 1984

    2011-01-01

    English is an international language, which has had great influence on other languages, including German; but it is also a language that has borrowed intensively from other languages, including German. When counting German loanwords in English, some scholars include all words that have ever been created by a German speaker. This is what Pfeffer and Cannon (1994) do in their comprehensive dictionary on German loanwords, but they count about 6,000 words. The aim of this essay is twofold: ...

  19. Electrical transport measurements of individual bismuth nanowires and carbon nanotubes

    Science.gov (United States)

    Jang, Wan Young

    Nanostructures are defined by reducing dimensions. When the reduced size of materials is comparable to the Fermi wavelength, quantum size effect occurs. Dimensionality plays a critical role in determining the electronic properties of materials, because the density of states of materials is quite different. Nanowires have attracted much attention recently due to their fundamental interest and potential applications. A number of materials have been tried. Among them, bismuth has unique properties. Bismuth has the smallest effective mass as small as 0.001me. This small effective mass of Bi nanowires allows one to observe the quantum confinement effect easily. Also Bi nanowires are good candidates for a low-dimensional transport study due to long mean free path. Because of these remarkable properties of Bi nanowires, many efforts have been made to study Bi nanowires. However, because bismuth is extremely sensitive to the oxide, it is very difficult to make a reliable device. So far, array measurements of Bi nanowires have been reported. The study is focused on the synthesis and electric transport measurements of individual Bi nanowires. Bi nanowires are synthesized by electrodeposition using either anodic aluminum oxide (AAO) templates or commercially available track etched polycarbonate membranes (PCTE). The desired nanowire has a heterostructure of Au - Bi - Au. Au wires on both sides serve as contact electrodes with Bi. To extract nanowires from PCTE or AAO, several attempts have been made. Devices consisting of single Bi nanowires grown by hydrothermal method are fabricated and electrical measurements have been carried out after in-situ deposition of Pt electrodes. The temperature dependence of resistance of majority of nanowires increases with decreasing temperature, showing polycrystalline nature of nanowires. However, some nanowires show resistance peaks at low temperature, suggesting quantum size effect (QSE). Magnetoresistance (MR) has also been measured. We

  20. Corrosion behavior of Si-enriched steels for nuclear applications in liquid lead–bismuth

    Energy Technology Data Exchange (ETDEWEB)

    Kurata, Yuji, E-mail: kurata.yuji@jaea.go.jp [Japan Atomic Energy Agency, Tokai-mura, Ibaraki-ken 319-1195 (Japan)

    2013-06-15

    Highlights: ► The corrosion behavior of Si-enriched steels in liquid lead–bismuth was studied. ► The corrosion tests were conducted at the two controlled oxygen levels. ► The Si addition reduces the scale thickness under the high oxygen condition. ► The Si addition has no significant effect under the low oxygen condition. -- Abstract: The corrosion behavior of Si-enriched steels in liquid lead–bismuth was studied in order to develop accelerator driven systems for transmutation of long-lived radioactive wastes and lead–bismuth cooled fast reactors. The corrosion tests of 316SS, Si-enriched 316SS, Mod.9Cr–1Mo steel (T91) and Si-enriched T91 were conducted at 550 °C in liquid lead–bismuth at the two controlled oxygen levels. Both the additions of 2.5 wt.% Si to 316SS and 1.5 wt.% Si to T91 had the effect of reducing the thickness of oxide layer in liquid lead–bismuth at the high oxygen concentration (2.5 × 10{sup −5} wt.%). Although the Si addition to 316SS reduced the depth of ferritization caused by Ni dissolution in liquid lead–bismuth at the low oxygen concentration (4.4 × 10{sup −8} wt.%), it could not suppress the ferritization and the penetration of Pb and Bi completely. The Si addition to T91 did not have the effect of preventing the penetration of Pb and Bi in the liquid lead–bismuth at the low oxygen concentration. The oxide scales formed on both Si-enriched steels did not have sufficient corrosion resistance under the low oxygen condition.

  1. Bismuth oxide aqueous colloidal nanoparticles inhibit Candida albicans growth and biofilm formation

    Directory of Open Access Journals (Sweden)

    Hernandez-Delgadillo R

    2013-04-01

    Full Text Available Rene Hernandez-Delgadillo,1 Donaji Velasco-Arias,3 Juan Jose Martinez-Sanmiguel,2 David Diaz,3 Inti Zumeta-Dube,3 Katiushka Arevalo-Niño,1 Claudio Cabral-Romero2 1Facultad de Ciencias Biológicas, Instituto de Biotecnologia, Universidad Autonoma de Nuevo Leon, UANL, Monterrey, Mexico; 2Facultad de Odontología, Universidad Autonoma de Nuevo Leon, UANL, Monterrey, México; 3Facultad de Quimica, Universidad Nacional Autonoma de Mexico, UNAM, Distrito Federal, México Abstract: Multiresistance among microorganisms to common antimicrobials has become one of the most significant concerns in modern medicine. Nanomaterials are a new alternative to successfully treat the multiresistant microorganisms. Nanostructured materials are used in many fields, including biological sciences and medicine. Recently, it was demonstrated that the bactericidal activity of zero-valent bismuth colloidal nanoparticles inhibited the growth of Streptococcus mutans; however the antimycotic potential of bismuth nanostructured derivatives has not yet been studied. The main objective of this investigation was to analyze the fungicidal activity of bismuth oxide nanoparticles against Candida albicans, and their antibiofilm capabilities. Our results showed that aqueous colloidal bismuth oxide nanoparticles displayed antimicrobial activity against C. albicans growth (reducing colony size by 85% and a complete inhibition of biofilm formation. These results are better than those obtained with chlorhexidine, nystatin, and terbinafine, the most effective oral antiseptic and commercial antifungal agents. In this work, we also compared the antimycotic activities of bulk bismuth oxide and bismuth nitrate, the precursor metallic salt. These results suggest that bismuth oxide colloidal nanoparticles could be a very interesting candidate as a fungicidal agent to be incorporated into an oral antiseptic. Additionally, we determined the minimum inhibitory concentration for the synthesized

  2. New bismuth borophosphate Bi4BPO10: Synthesis, crystal structure, optical and band structure analysis

    International Nuclear Information System (INIS)

    New bismuth borophosphate Bi4BPO10 was obtained by spontaneous crystallization from the melt of correspondent composition at 804 °C. Crystal structure with orthorhombic lattice parameters: a = 22.5731(3) Å, b = 14.0523(2) Å, c = 5.5149(1) Å, V = 1749.34(4), Z = 8, SG Pcab was determined by X-ray powder diffraction technique. The [Bi2O2]2+ -layers, which are typical for bismuth oxide compounds, transform into cationic endless strips of 4 bismuth atoms width directed along the c-axis in Bi4BPO10. The strips combining stacks are separated by flat triangle [BO3]3− -anions within stacks. Neighboring stacks are separated by tetrahedral [PO4]3−-anions and shifted relatively to each other. Bismuth atoms are placed in 5–7 vertex oxygen irregular polyhedra. Bi4BPO10 is stable up to 812 °C, then melts according to the peritectic law. The absorption spectrum in the range 350–700 nm was obtained and the width of the forbidden band was estimated as 3.46 eV. The band electronic structure of Bi4BPO10 was modeled using DFT approach. The calculated band gap (3.56 eV) is in good agreement with the experimentally obtained data. - Graphical abstract: Display Omitted - Highlights: • New bismuth borophosphate with composition Bi4BPO10 was synthesized. • The crystal structure was determined by X-ray powder diffraction technique. • Bismuth-oxygen part [Bi4O3]6+ forms endless strips of 4 bismuth atoms width. • Electronic structure was modeled by DFT method. • The calculated band gap (3.56 eV) is very close to the experimental one (3.46 eV)

  3. Zerovalent bismuth nanoparticles inhibit Streptococcus mutans growth and formation of biofilm

    Directory of Open Access Journals (Sweden)

    Hernandez-Delgadillo R

    2012-04-01

    Full Text Available Rene Hernandez-Delgadillo1, Donaji Velasco-Arias2, David Diaz2, Katiushka Arevalo-Niño1, Marianela Garza-Enriquez1, Myriam A De la Garza-Ramos1, Claudio Cabral-Romero11Instituto de Biotecnologia, Centro de Investigacion y Desarrollo en Ciencias de la Salud, CIDICS, Facultad de Odontologia, Universidad Autonoma de Nuevo Leon, UANL, Monterrey, Nuevo Leon, 2Facultad de Quimica, Universidad Nacional Autonoma de Mexico, Distrito Federal, MexicoBackground and methods: Despite continuous efforts, the increasing prevalence of resistance among pathogenic bacteria to common antibiotics has become one of the most significant concerns in modern medicine. Nanostructured materials are used in many fields, including biological sciences and medicine. While some bismuth derivatives has been used in medicine to treat vomiting, nausea, diarrhea, and stomach pain, the biocidal activity of zerovalent bismuth nanoparticles has not yet been studied. The objective of this investigation was to analyze the antimicrobial activity of bismuth nanoparticles against oral bacteria and their antibiofilm capabilities.Results: Our results showed that stable colloidal bismuth nanoparticles had 69% antimicrobial activity against Streptococcus mutans growth and achieved complete inhibition of biofilm formation. These results are similar to those obtained with chlorhexidine, the most commonly used oral antiseptic agent. The minimal inhibitory concentration of bismuth nanoparticles that interfered with S. mutans growth was 0.5 mM.Conclusion: These results suggest that zerovalent bismuth nanoparticles could be an interesting antimicrobial agent to be incorporated into an oral antiseptic preparation.Keywords: zerovalent bismuth nanoparticles, antimicrobial agent, biofilm, Streptococcus mutans

  4. Synthesis, Characterization and Molecular Structures of some Bismuth(III) Complexes with Thiosemicarbazones and Dithiocarbazonic Acid Methylester Derivatives with Activity against Helicobacter Pylori

    OpenAIRE

    Diemer, Rolf; Dittes, Uwe; Nuber, Bernhard; Seifried, Volker; Opferkuch, Wolfgang; Keppler, Bernhard K.

    1995-01-01

    The reactions of bismuth(III) nitrate pentahydrate and bismuth(III) chloride with heterocyclic thiosemicarbazones and derivatives of dithiocarbazonic acid methylester were used to synthesize the respective bismuth(III) complexes, which could be divided into five groups D-H because of their stoichiometrical properties and their molecular structures. The molecular structure and the near coordination sphere of the bismuth(III) central atom of four representative compounds were determined by sing...

  5. Dictionary for veterinary science and biosciences. German-English/English-German. With trilingual appendix: Latin terms

    International Nuclear Information System (INIS)

    This dictionary has been compiled as a result of many years experience of translating German texts in the biological sciences, particularly veterinary medicine. The author's aim is to supplement the standard German-English general dictionaries with technical terms to in the fields of anatomy, microbiology, physiology, parasitology, pathology, pharmacology, toxicology and zootechny, with special reference to domestic animals and their diseases. (orig.)

  6. German Basic Course. Cumulative Word List: Lessons 1-92. German-English.

    Science.gov (United States)

    Defense Language Inst., Monterey, CA.

    This glossary contains all the words and idioms in the nine volumes of the elementary and intermediate phases of a basic course in German. In each entry the German word is listed first followed by the English word and the number of the lesson in which the word first appeared. (AMH)

  7. German Basic Course. Cumulative Word List: Lessons 1-92. English-German.

    Science.gov (United States)

    Defense Language Inst., Monterey, CA.

    This glossary contains all the words and idioms in the nine volumes of the elementary and intermediate phases of a basic course in German. In each entry the English word is listed first followed by the German word and the number of the lesson in which the word first appeared. (AMH)

  8. Electrochemical study on determination of diffusivity, activity and solubility of oxygen in liquid bismuth

    Energy Technology Data Exchange (ETDEWEB)

    Ganesan, Rajesh [Liquid Metals and Structural Chemistry Division, Chemistry Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India); Gnanasekaran, T. [Liquid Metals and Structural Chemistry Division, Chemistry Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102 (India)]. E-mail: gnani@igcar.ernet.in; Srinivasa, Raman S. [Department of Metallurgical Engineering and Materials Science, Indian Institute of Technology Bombay, Mumbai 400 076 (India)

    2006-06-15

    Diffusivity of oxygen in liquid bismuth was measured by potentiostatic method and is given bylg(D{sub O}{sup Bi}/cm{sup 2}.s{sup -1})(+/-0.042)=-3.706-1377/(TK{sup -1})(804bismuth was determined by coulometric titrations and using the measured data standard free energy of dissolution of oxygen in liquid bismuth was derived for the reaction:1/2O{sub 2}(g)=[O]{sub Bi}(at.%)and is given by{delta}G{sub O(Bi)}{sup o}/(J.g-atomO{sup -1})(+/-720)=-108784+20.356TK{sup -1}(753bismuth was derived as a function of temperature and is given by the following expressions:lg(S/at%O)(+/-0.05)=-4476/TK{sup -1}+4.05(753bismuth is compared with the literature data.

  9. Bismuth nanoparticles synthesized by laser ablation in lubricant oils for tribological tests

    International Nuclear Information System (INIS)

    Highlights: • Bismuth nanoparticles have been obtained by laser ablation of solids in liquids. • The technique allows controlling the size and concentration of the samples. • Bi np’s in base oils can improve the tribological characteristics of the lubricant. - Abstract: The improvement of the tribological properties of mineral base oils through the addition of bismuth nanoparticles as an additive, together with the idea of obtaining lubricants free of heavy metals, was evaluated. Bismuth nanoparticles were produced directly in the heavy and light viscosity mineral base oils (BS900 and BS6500) using the technique of laser ablation of solids immersed in liquids. Transmission electron microscopy measurements showed the presence of pure bismuth nanoparticles. Small Angle X-ray Scattering (SAXS) measurements showed that the average size of the nanoparticles was between 7 and 65 nm depending on the experimental conditions used. The tribological properties of the base oil with the bismuth nanoparticles additives were evaluated using a four-ball tester. Tests were performed using the base oil with and without Bi nanoparticles. It was observed that the coefficient of friction of the oil decrease with an increasing concentration of the nanoparticles. The results also showed that the wear rate was reduced when the Bi nanoparticle additives were used

  10. Crystallinity and electrical properties of neodymium-substituted bismuth titanate thin films

    International Nuclear Information System (INIS)

    We report on the properties of Nd-substituted bismuth titanate Bi4-xNd xTi3O12 (BNdT) thin films for ferroelectric non-volatile memory applications. The Nd-substituted bismuth titanate thin films fabricated by modified chemical solution deposition technique showed much improved properties compared to pure bismuth titanate. A pyrochlore free crystalline phase was obtained at a low annealing temperature of 640 deg. C and grain size was found to be considerably increased as the annealing temperature increased. The film properties were found to be strongly dependent on the Nd content and annealing temperatures. The measured dielectric constant of BNdT thin films was in the range 172-130 for Bi4-xNd xTi3O12 with x 0.0-0.75. Ferroelectric properties of Nd-substituted bismuth titanate thin films were significantly improved compared to pure bismuth titanate. For example, the observed 2P r and E c for Bi3.25Nd0.75Ti3O12, annealed at 680 deg. C, were 38 μC/cm2 and 98 kV/cm, respectively. The improved microstructural and ferroelectric properties of BNdT thin films suggest their suitability for high density ferroelectric random access memory applications

  11. Bismuth Modified Carbon-Based Electrodes for the Determination of Selected Neonicotinoid Insecticides

    Directory of Open Access Journals (Sweden)

    Marko Rodić

    2011-05-01

    Full Text Available Two types of bismuth modified electrodes, a bismuth-film modified glassy carbon (BiF-GCE and a bismuth bulk modified carbon paste, were applied for the determination of selected nitroguanidine neonicotinoid insecticides. The method based on an ex situ prepared BiF-GCE operated in the differential pulse voltammetric (DPV mode was applied to determine clothianidin in the concentration range from 2.5 to 23 μg cm−3 with a relative standard deviation (RSD not exceeding 1.5%. The tricresyl phosphate-based carbon paste electrodes (TCP-CPEs, bulk modified with 5 and 20 w/w% of bismuth, showed a different analytical performance in the determination of imidacloprid, regarding the peak shape, potential window, and noise level. The TCP-CPE with 5% Bi was advantageous, and the developed DPV method based on it allowed the determination in the concentration range from 1.7 to 60 μg cm−3 with an RSD of 2.4%. To get a deeper insight into the morphology of the bismuth-based sensor surfaces, scanning electron microscopic measurements were performed of both the surface film and the bulk modified electrodes.

  12. Bioaccumulation and biosorption of bismuth Bi (III) by filamentous fungus Aspergillus clavatus

    International Nuclear Information System (INIS)

    In this work we focused on bismuth (III) biosorption and bioaccumulation. Prior the bioaccumulation experiments the 7-day-old conidia were collected from mycelia surface of filamentous fungus Aspergillus clavatus and used as inocula for 50 ml of nutrient media with different bismuth (III) concentrations. After 15-day cultivation under laboratory conditions (dark, 25 grad C) the bismuth concentration in grown fungal biomass was measured using ICP OES. Maximum achieved accumulation capacity of dry biomass was 112 μmol.g-1. Batch biosorption experiments were performed in Erlenmeyer flasks with pelletized wet fungal biomass/solution ratio 1.8% and with various bismuth (III) concentrations. The equilibrium time was studied within the time interval of 0-240 min. The reaction kinetics were well described by both pseudo-first and pseudo-second order rate models, and equilibrium was reached after 50 min. Langmuir and Freundlich isotherm models were used to represent equilibrium data, and the calculated maximum biosorption capacity of fungal biomass for bismuth(III) was 0.40 mmol.g-1. (authors)

  13. Bismuth nanoparticles synthesized by laser ablation in lubricant oils for tribological tests

    Energy Technology Data Exchange (ETDEWEB)

    Flores-Castañeda, M., E-mail: mar.floc@hotmail.com [Universidad Autónoma del Estado de México, Av. Instituto Literario No. 100, Oriente Col. Centro, Toluca, Estado de México C.P. 50000, México (Mexico); Instituto Nacional de Investigaciones Nucleares, Carretera México-Toluca s/n, La Marquesa, Ocoyoacac, Edo. de México C.P. 52750, México (Mexico); Camps, E. [Instituto Nacional de Investigaciones Nucleares, Carretera México-Toluca s/n, La Marquesa, Ocoyoacac, Edo. de México C.P. 52750, México (Mexico); Camacho-López, M. [Universidad Autónoma del Estado de México, Av. Instituto Literario No. 100, Oriente Col. Centro, Toluca, Estado de México C.P. 50000, México (Mexico); Muhl, S. [Instituto de Investigación en Materiales (UNAM), Circuito Exterior, Ciudad Universitaria, Coyoacán, 04510 México, D.F., México (Mexico); and others

    2015-09-15

    Highlights: • Bismuth nanoparticles have been obtained by laser ablation of solids in liquids. • The technique allows controlling the size and concentration of the samples. • Bi np’s in base oils can improve the tribological characteristics of the lubricant. - Abstract: The improvement of the tribological properties of mineral base oils through the addition of bismuth nanoparticles as an additive, together with the idea of obtaining lubricants free of heavy metals, was evaluated. Bismuth nanoparticles were produced directly in the heavy and light viscosity mineral base oils (BS900 and BS6500) using the technique of laser ablation of solids immersed in liquids. Transmission electron microscopy measurements showed the presence of pure bismuth nanoparticles. Small Angle X-ray Scattering (SAXS) measurements showed that the average size of the nanoparticles was between 7 and 65 nm depending on the experimental conditions used. The tribological properties of the base oil with the bismuth nanoparticles additives were evaluated using a four-ball tester. Tests were performed using the base oil with and without Bi nanoparticles. It was observed that the coefficient of friction of the oil decrease with an increasing concentration of the nanoparticles. The results also showed that the wear rate was reduced when the Bi nanoparticle additives were used.

  14. Role of bismuth in improving Helicobacter pylori eradication with triple therapy.

    Science.gov (United States)

    Dore, Maria Pina; Lu, Hong; Graham, David Y

    2016-05-01

    In most regions of the world, antimicrobial resistance has increased to the point where empirical standard triple therapy forHelicobacter pylorieradication is no longer recommended. The treatment outcome in a population is calculated as the sum of the treatment success in the subpopulation with susceptible infections plus treatment success in the subpopulation with resistant infections. The addition of bismuth (ie, 14-day triple therapy plus bismuth) can improve cure rates despite a high prevalence of antimicrobial resistance. The major bismuth effect is to add an additional 30%-40% to the success with resistant infections. The overall result is therefore dependent on the prevalence of resistance and the treatment success in the subpopulation with resistant infections (eg, with proton-pump inhibitor-amoxicillin dual therapy). Here, we explore the contribution of each component and the mechanisms of how bismuth might enhance the effectiveness of triple therapy. We also discuss the limitations of this approach and provide suggestions how triple therapy plus bismuth might be further improved. PMID:26848181

  15. Magnetoelectric Effect in Ceramics Based on Bismuth Ferrite

    Science.gov (United States)

    Jartych, Elżbieta; Pikula, Tomasz; Kowal, Karol; Dzik, Jolanta; Guzdek, Piotr; Czekaj, Dionizy

    2016-04-01

    Solid-state sintering method was used to prepare ceramic materials based on bismuth ferrite, i.e., (BiFeO3)1 - x -(BaTiO3) x and Bi1 - x Nd x FeO3 solid solutions and the Aurivillius Bi5Ti3FeO15 compound. The structure of the materials was examined using X-ray diffraction, and the Rietveld method was applied to phase analysis and structure refinement. Magnetoelectric coupling was registered in all the materials using dynamic lock-in technique. The highest value of magnetoelectric coupling coefficient α ME was obtained for the Bi5Ti3FeO15 compound ( α ME ~ 10 mVcm-1 Oe-1). In the case of (BiFeO3)1 - x -(BaTiO3) x and Bi1 - x Nd x FeO3 solid solutions, the maximum α ME is of the order of 1 and 2.7 mVcm-1 Oe-1, respectively. The magnitude of magnetoelectric coupling is accompanied with structural transformation in the studied solid solutions. The relatively high magnetoelectric effect in the Aurivillius Bi5Ti3FeO15 compound is surprising, especially since the material is paramagnetic at room temperature. When the materials were subjected to a preliminary electrical poling, the magnitude of the magnetoelectric coupling increased 2-3 times.

  16. Ferroelectric and photocatalytic behavior of bismuth ferrite nano wire

    Science.gov (United States)

    William, R. V.; Marikani, A.; Madhavan, D.

    2016-05-01

    Multiferroic bismuth ferrite nanowires are prepared through polyol method with an average diameter of 35 nm with a narrow size distribution. The band gap was determined to be 2.10 eV, indicating their potential application as visible-light-response photo catalyst. The magnificent photocatalytic behaviors of BiFeO3 nanowires are understood from the methyl violet degradation under visible light irradiation. Moreover, the nano-wire takes only a lesser time for the diffusion of electron-hole pair from the surface of the sample. Further the BiFeO3 nano-wire was characterized using XRD, SEM, and U-V. The ferroelectric studies of BiFeO3 nano-wire show a frequency dependent property and maximum coercivity of 2.7 V/cm were achieved with a remanent polarization at 0.5 µC/cm2 at the frequency 4 kHz. The coercivity of BiFeO3 nano wire changes with variation of frequency from 1 kHz to 4 kHz.

  17. Characterization of electrodeposited bismuth-tellurium nanowires and nanotubes

    International Nuclear Information System (INIS)

    Arrays of nanowires and nanotubes of bismuth-tellurium (Bi-Te) were fabricated by electrodeposition techniques. Scanning electron microscopy was employed to characterize the morphology of the fabricated BiTe nanowires and nanotubes. The fabricated BiTe nanowire and nanotube arrays are shown to be polycrystalline with no preferred orientation. Wavelength dispersive spectroscopy analysis shows that either p-type (Bi rich) or n-type (Te rich) nanowires or nanotubes can be obtained by changing the electrodeposition potentials. The lamellar thickness of the nanowires and nanotube crystallites were determined using the Scherrer equation and found to be ∼17-24 nm. The Seebeck coefficient measurements at room temperature obtained for the nanowires and nanotubes deposited at -400 mV were +11.5 and +17 μV K-1, respectively, whereas those obtained at -65 mV were -48 and -63 μV K-1, respectively. The electrical resistance measurements indicated that the resistance of the nanowires and nanotubes decreased with increasing temperature, suggesting that these nanostructures behave like semiconductors.

  18. Transport phenomena in nanowires based on bismuth alloys

    International Nuclear Information System (INIS)

    Full text: In this work, we study the conductivity and thermopower of quantum wires (QW) based on bismuth alloys. Calculations are carried out for nanowires with degenerate and nondegenerate gas of carriers at various crystalline orientations taking into account the real band structure of Bi. We find the energy eigenvalues of holes and taking into account the nonparabolicity of the band, the energy eigenvalues for electrons. The conductivity and thermopower determined with the use of the Kubo formulae in the case when the basic mechanism of carrier scattering is assumed to be elastic acoustic-phonon scattering and on a roughness surface of QW. Dependences of kinetic coefficients on temperature, nanowire diameter and crystalline orientation are investigated. The conductivity and thermopower of a QW contains the contributions of electrons and holes. Taking into account values of carrier effective masses and other band parameters of Bi, it is possible to conclude that the contribution of holes to the conductivity of nondegenerate carriers of QWs is more less than that of electrons, which is attributed to smaller effective mass of electrons. For a semiconducting Bi QW the conductivity depends exponentially on a temperature and wire diameter. The thermopower of a semiconducting and of a semimetallic Bi QW at low temperatures can be positive and change sign in more higher temperatures. The theoretical results are close to experiment for Bi wires with diameter of 50-100 nm. (author)

  19. Bismuth alloying properties in GaAs nanowires

    International Nuclear Information System (INIS)

    First-principles calculations have been performed to investigate the structural, electronic and optical properties of bismuth alloying in GaAs nanowires. A typical model of Ga31As31 nanowires is introduced for its reasonable band gap. The band gap of GaAs1−xBix shrinks clearly with the increasing Bi concentration and the band edge shifts when spin–orbit coupling (SOC) is considered. The insertion of Bi atom leads to hybridization of Ga/As/Bi p states which contributes a lot around Fermi level. Scissor effect is involved. The optical properties are presented, including dielectric function, optical absorption spectra and reflectivity, which are also varied with the increasing of Bi concentrations. - Graphical abstract: Top view of Bi-doped GaAs nanowires. Ga, As, and Bi atoms are denoted with grey, purple and red balls, respectively. Display Omitted - Highlights: • A typical model of Ga31As31 nanowires is introduced for its reasonable band gap. • The band gap of GaAs1−xBix shrinks clearly with the increasing Bi concentration. • The band edge shifts when spin–orbit coupling (SOC) is considered. • The insertion of Bi atom leads to hybridization of Ga/As/Bi p states

  20. Antibacterial effect of bismuth subsalicylate nanoparticles synthesized by laser ablation

    Energy Technology Data Exchange (ETDEWEB)

    Flores-Castañeda, Mariela [Instituto Nacional de Investigaciones Nucleares (Mexico); Vega-Jiménez, Alejandro L., E-mail: argelia.almaguer@mac.com; Almaguer-Flores, Argelia [Universidad Nacional Autónoma de México, Facultad de Odontología, DEPeI, I (Mexico); Camps, Enrique; Pérez, Mario [Instituto Nacional de Investigaciones Nucleares (Mexico); Silva-Bermudez, Phaedra [Instituto Nacional de Rehabilitación, Unidad de Ingeniería de Tejidos, Terapia Celular y Medicina Regenerativa (Mexico); Berea, Edgardo [FarmaQuimia SA de CV. (Mexico); Rodil, Sandra E. [Universidad Nacional Autónoma de México, Instituto de Investigaciones en Materiales (Mexico)

    2015-11-15

    The antimicrobial properties of bismuth subsalicylate (BSS) nanoparticles against four opportunistic pathogens; E. coli, P. aeruginosa, S. aureus, and S. epidermidis were determined. BSS nanoparticles were synthesized by pulse laser ablation of a solid target in distilled water under different conditions. The nanoparticles were characterized using high-resolution transmission electron microscopy and absorption spectra and small angle X-ray scattering. The analysis shows that the colloids maintained the BSS structure and presented average particle size between 20 and 60 nm, while the concentration ranges from 95 to 195 mg/L. The antibacterial effect was reported as the inhibition ratio of the bacterial growth after 24 h and the cell viability was measured using the XTT assay. The results showed that the inhibition ratio of E. coli and S. epidermidis was dependant on the NPs size and/or concentration, meanwhile P. aeruginosa and S. aureus were more sensitive to the BSS nanoparticles independently of both the size and the concentration. In general, the BSS colloids with average particle size of 20 nm were the most effective, attaining inhibition ratios >80 %, similar or larger than those obtained with the antibiotic used as control. The results suggest that the BSS colloids could be used as effective antibacterial agents with potential applications in the medical area.

  1. Investigation of solution-processed bismuth-niobium-oxide films

    Energy Technology Data Exchange (ETDEWEB)

    Inoue, Satoshi, E-mail: s-inoue@jaist.ac.jp [Green Device Research Center, Japan Advanced Institute of Science and Technology (JAIST), 2-13 Asahidai, Nomi, Ishikawa 923-1211 (Japan); School of Material Science, Japan Advanced Institute of Science and Technology (JAIST), 1-1 Asahidai, Nomi, Ishikawa 923-1292 (Japan); Ariga, Tomoki [Green Device Research Center, Japan Advanced Institute of Science and Technology (JAIST), 2-13 Asahidai, Nomi, Ishikawa 923-1211 (Japan); ERATO Shimoda Nano-Liquid Process Project, Japan Science and Technology Agency (JST), 2-13 Asahidai, Nomi, Ishikawa 923-1211 (Japan); Matsumoto, Shin [School of Material Science, Japan Advanced Institute of Science and Technology (JAIST), 1-1 Asahidai, Nomi, Ishikawa 923-1292 (Japan); Onoue, Masatoshi; Miyasako, Takaaki [ERATO Shimoda Nano-Liquid Process Project, Japan Science and Technology Agency (JST), 2-13 Asahidai, Nomi, Ishikawa 923-1211 (Japan); Tokumitsu, Eisuke; Shimoda, Tatsuya [Green Device Research Center, Japan Advanced Institute of Science and Technology (JAIST), 2-13 Asahidai, Nomi, Ishikawa 923-1211 (Japan); School of Material Science, Japan Advanced Institute of Science and Technology (JAIST), 1-1 Asahidai, Nomi, Ishikawa 923-1292 (Japan); ERATO Shimoda Nano-Liquid Process Project, Japan Science and Technology Agency (JST), 2-13 Asahidai, Nomi, Ishikawa 923-1211 (Japan); Chinone, Norimichi; Cho, Yasuo [Research Institute of Electrical Communication, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan)

    2014-10-21

    The characteristics of bismuth-niobium-oxide (BNO) films prepared using a solution process were investigated. The BNO film annealed at 550°C involving three phases: an amorphous phase, Bi₃NbO₇ fluorite microcrystals, and Nb-rich cubic pyrochlore microcrystals. The cubic pyrochlore structure, which was the main phase in this film, has not previously been reported in BNO films. The relative dielectric constant of the BNO film was approximately 140, which is much higher than that of a corresponding film prepared using a conventional vacuum sputtering process. Notably, the cubic pyrochlore microcrystals disappeared with increasing annealing temperature and were replaced with triclinic β-BiNbO₄ crystals at 590°C. The relative dielectric constant also decreased with increasing annealing temperature. Therefore, the high relative dielectric constant of the BNO film annealed at 550°C is thought to result from the BNO cubic pyrochlore structure. In addition, the BNO films annealed at 500°C contained approximately 6.5 atm.% carbon, which was lost at approximately 550°C. This result suggests that the carbon in the BNO film played an important role in the formation of the cubic pyrochlore structure.

  2. Optical bleaching of bismuth implanted silica glass: A threshold effect

    International Nuclear Information System (INIS)

    The near surface regions of high purity silica glass discs, Spectrosil A, were modified by implantation with bismuth ions at 160 keV and room temperature. The glasses implanted with a nominal dose of 6 x 1016 Bi/cm2 at ∼5 μA/cm2 were subsequently bleached with a 5.0 eV KrF pulsed excimer laser. The laser had an average pulse duration of ∼20 ns and repetition rate of 10 Hz, It was found that the bleaching was dependent upon the power density of the laser for a constant total integrated energy. Ion backscattering and optical absorption measurements were made before and after laser irradiation. Large changes in optical density and depth distribution of the implanted ions were observed at power densities of ≥45 mJ/cm2-pulse. On the basis of the experimental results, the onset of the threshold for bleaching of silica glass implanted with 6 x 1016 Bi/cm2 at 160 keV and at room temperature is between 30 and 45 mJ/cm2-pulse

  3. Modular Lead-Bismuth Fast Reactors in Nuclear Power

    Directory of Open Access Journals (Sweden)

    Vladimir Petrochenko

    2012-09-01

    Full Text Available On the basis of the unique experience of operating reactors with heavy liquid metal coolant–eutectic lead-bismuth alloy in nuclear submarines, the concept of modular small fast reactors SVBR-100 for civilian nuclear power has been developed and validated. The features of this innovative technology are as follows: a monoblock (integral design of the reactor with fast neutron spectrum, which can operate using different types of fuel in various fuel cycles including MOX fuel in a self-providing mode. The reactor is distinct in that it has a high level of self-protection and passive safety, it is factory manufactured and the assembled reactor can be transported by railway. Multipurpose application of the reactor is presumed, primarily, it can be used for regional power to produce electricity, heat and for water desalination. The Project is being realized within the framework of state-private partnership with joint venture OJSC “AKME-Engineering” established on a parity basis by the State Atomic Energy Corporation “Rosatom” and the Limited Liability Company “EuroSibEnergo”.

  4. A detailed study of 2223 bismuth superconductor system

    International Nuclear Information System (INIS)

    In an attempt to obtain improved Phase conditions, Critical current density and Tc, in Bismuth based 2223 superconducting, eleven batches of samples of Bi/sub 2-x/, (Pb/sub x-y/ Sb/sub y/) Sr/sub 2/ Ca/sub 2/Cu/sub 3/O delta series, where (x,y) =(0.5,0.4), (0.32, 0), (0.4, 0.2), (o.4, 0.1), (0.3, 0.2), (0.3, 0.1), (0.2, 0.1), (0.1, 0.1) and (0.1, 0) were prepared using solid state reaction method. Electrical resistivity measurements on samples showed normal superconductor behavior with a dominating superconducting phase of 110K as well as a quite improved critical current. However two samples of series showed semiconductor behavior up to LN2 temperature. X-ray diffraction analysis have also been made on samples which showed a multiphase. (author)

  5. Synthesis and characterization of bismuth zinc niobate pyrochlore nanopowders

    Directory of Open Access Journals (Sweden)

    Sonia Maria Zanetti

    2007-09-01

    Full Text Available Bismuth zinc niobate pyrochlores Bi1.5ZnNb1.5O7 (alpha-BZN, and Bi2(Zn1/3Nb2/32O 7 (beta-BZN have been synthesized by chemical method based on the polymeric precursors. The pyrochlore phase was investigated by differential scanning calorimetry, infrared spectroscopy, and X ray diffraction. Powder and sintered pellets morphology was examined by scanning electron microscopy. The study of alpha-BZN phase formation reveals that, at 500 °C, the pyrochlore phase was already present while a single-phased nanopowder was obtained after calcination at 700 °C. The crystallization mechanism of the beta-BZN is quite different, occurring through the crystallization of alpha-BZN and BiNbO4 intermediary phases. Both compositions yielded soft agglomerated powders. alpha-BZN pellets, sintered at 800 °C for 2 hours, presented a relative density of 97.3% while those of beta-BZN, sintered at 900 °C for 2 hours, reached only 91.8%. Dielectric constant and dielectric loss, measured at 1 MHz, were 150 and 4 x/10-4 for a-BZN, and 97 and 8 x 10-4 for beta-BZN.

  6. Synthesis and characterization of bismuth doped barium sulphide nanoparticles

    International Nuclear Information System (INIS)

    We have synthesized BaS:Bi nanocrystalline powder of average grain size 35 nm by solid-state diffusion method using sodium thiosulphate as a flux. During this work we have optimized the nature and amount of flux, amount of the dopant and temperature of firing for maximum yield of photoluminescence. The samples were characterized by X-ray powder diffraction (XRD) method, transmission electron microscopy (TEM), photoluminescence (PL) and UV-visible techniques. On excitation by 425 nm, these nanophosphors give one emission peak at 575 nm which corresponds to green color. In the excitation spectra of these particles there are two peaks at 350 nm and 425 nm. The effect of dopant concentration on the photoluminescence of BaS:Bi nanocrystallites has been studied which is in agreement with the principle of concentration quenching. The energy band gap of bismuth doped BaS nanopowder has been calculated to be 4.25 eV and is blue shifted in comparison to their bulk counterparts. The blue shift may be due to the quantum confinement in the particles.

  7. Optical bleaching of bismuth implanted silica glass: A threshold effect

    International Nuclear Information System (INIS)

    The near surface regions of high purity silica glass discs, Spectrosil A, were modified by implantation with bismuth ions at 160 key and room temperature. The glasses implanted with a nominal dose of 6x1016 Bi/cm2 at ∼5 μA/cm2 were subsequently bleached with a 5.0 eV KrF pulsed excimer laser. The laser had an average pulse duration of ∼20 ns and repetition rate of 10 Hz. It was found that the bleaching was dependent upon the power density of the laser for a constant total integrated energy. Ion backscattering and optical absorption measurements were made before and after laser irradiation. Large changes in optical density and depth distribution of the implanted ions were observed at power densities of ≥45 mJ/cm2-pulse. Onset of threshold for bleaching of silica glass implanted with 6x1016 Bi/cm2 at 160 key and at room temperature is between 30 and 45 mJ/cm2-pulse

  8. Bismuth nanoparticles integration into heavy metal electrochemical stripping sensor.

    Science.gov (United States)

    Cadevall, Miquel; Ros, Josep; Merkoçi, Arben

    2015-08-01

    Between their many applications bismuth nanoparticles (BiNPs) are showing interest as pre-concentrators in heavy metals detection while being applied as working electrode modifiers used in electrochemical stripping analysis. From the different reported methods to synthesize BiNPs we are focused on the typical polyol method, largely used in these types of metallic and semi-metallic nanoparticles. This study presents the strategy for an easy control of the shape and size of BiNPs including nanocubes, nanosferes and triangular nanostructures. To improve the BiNP size and shape, different reducing agents (ethylene glycol or sodium hypophosphite) and stabilizers (polyvinyl pyrrolidone, PVP, in different amounts) have been studied. The efficiency of BiNPs for heavy metals analysis in terms of detection sensitivity while being used as modifiers of screen-printed carbon electrodes including the applicability of the developed device in real sea water samples is shown. A parallel study between the obtained nanoparticles and their performance in heavy metal sensing has been described in this communication. PMID:25994368

  9. Investigation of solution-processed bismuth-niobium-oxide films

    International Nuclear Information System (INIS)

    The characteristics of bismuth-niobium-oxide (BNO) films prepared using a solution process were investigated. The BNO film annealed at 550 °C involving three phases: an amorphous phase, Bi3NbO7 fluorite microcrystals, and Nb-rich cubic pyrochlore microcrystals. The cubic pyrochlore structure, which was the main phase in this film, has not previously been reported in BNO films. The relative dielectric constant of the BNO film was approximately 140, which is much higher than that of a corresponding film prepared using a conventional vacuum sputtering process. Notably, the cubic pyrochlore microcrystals disappeared with increasing annealing temperature and were replaced with triclinic β-BiNbO4 crystals at 590 °C. The relative dielectric constant also decreased with increasing annealing temperature. Therefore, the high relative dielectric constant of the BNO film annealed at 550 °C is thought to result from the BNO cubic pyrochlore structure. In addition, the BNO films annealed at 500 °C contained approximately 6.5 atm. % carbon, which was lost at approximately 550 °C. This result suggests that the carbon in the BNO film played an important role in the formation of the cubic pyrochlore structure.

  10. German neutron scattering conference. Programme and abstracts

    International Nuclear Information System (INIS)

    The German Neutron Scattering Conference 2012 - Deutsche Neutronenstreutagung DN 2012 offers a forum for the presentation and critical discussion of recent results obtained with neutron scattering and complementary techniques. The meeting is organized on behalf of the German Committee for Research with Neutrons - Komitee Forschung mit Neutronen KFN - by the Juelich Centre for Neutron Science JCNS of Forschungszentrum Juelich GmbH. In between the large European and international neutron scattering conferences ECNS (2011 in Prague) and ICNS (2013 in Edinburgh), it offers the vibrant German and international neutron community an opportunity to debate topical issues in a stimulating atmosphere. Originating from ''BMBF Verbundtreffen'' - meetings for projects funded by the German Federal Ministry of Education and Research - this conference series has a strong tradition of providing a forum for the discussion of collaborative research projects and future developments in the field of research with neutrons in general. Neutron scattering, by its very nature, is used as a powerful probe in many different disciplines and areas, from particle and condensed matter physics through to chemistry, biology, materials sciences, engineering sciences, right up to geology and cultural heritage; the German Neutron Scattering Conference thus provides a unique chance for exploring interdisciplinary research opportunities. It also serves as a showcase for recent method and instrument developments and to inform users of new advances at neutron facilities.

  11. German neutron scattering conference. Programme and abstracts

    Energy Technology Data Exchange (ETDEWEB)

    Brueckel, Thomas (ed.)

    2012-07-01

    The German Neutron Scattering Conference 2012 - Deutsche Neutronenstreutagung DN 2012 offers a forum for the presentation and critical discussion of recent results obtained with neutron scattering and complementary techniques. The meeting is organized on behalf of the German Committee for Research with Neutrons - Komitee Forschung mit Neutronen KFN - by the Juelich Centre for Neutron Science JCNS of Forschungszentrum Juelich GmbH. In between the large European and international neutron scattering conferences ECNS (2011 in Prague) and ICNS (2013 in Edinburgh), it offers the vibrant German and international neutron community an opportunity to debate topical issues in a stimulating atmosphere. Originating from ''BMBF Verbundtreffen'' - meetings for projects funded by the German Federal Ministry of Education and Research - this conference series has a strong tradition of providing a forum for the discussion of collaborative research projects and future developments in the field of research with neutrons in general. Neutron scattering, by its very nature, is used as a powerful probe in many different disciplines and areas, from particle and condensed matter physics through to chemistry, biology, materials sciences, engineering sciences, right up to geology and cultural heritage; the German Neutron Scattering Conference thus provides a unique chance for exploring interdisciplinary research opportunities. It also serves as a showcase for recent method and instrument developments and to inform users of new advances at neutron facilities.

  12. Chapter 10. On average contents of bismuth, indium and thallium in secondary sediments of depression of Tajikistan

    International Nuclear Information System (INIS)

    In this part of book author made conclusion that background contents of bismuth, indium and thallium in secondary sediments of depression of Tajikistan depend from petrographic composition of layers of drainage area, facial-climatic conditions and lithologic layer type; accumulation of investigated elements pass at coastal phases; clayey sediments more enriched by bismuth, indium and thallium than sandstones

  13. Overview of the use of ATHENA for thermal-hydraulic analysis of systems with lead-bismuth coolant

    International Nuclear Information System (INIS)

    The INEEL and MIT are investigating the suitability of lead-bismuth cooled fast reactor for producing low-cost electricity as well as for actinide burning. This paper is concerned with the general area of thermal-hydraulics of lead-bismuth cooled reactors. The ATHENA code is being used in the thermal-hydraulic design and analysis of lead-bismuth cooled reactors. The ATHENA code was reviewed to determine its applicability for simulating lead-bismuth cooled reactors. Two modifications were made to the code as a result of this review. Specifically, a correlation to represent heat transfer from rod bundles to a liquid metal and a void correlation based on data taken in a mixture of lead-bismuth and steam were added the code. The paper also summarizes the analytical work that is being performed with the code and plans for future analytical work

  14. Assessment of the Eye Lens Dose Reduction by Bismuth Shields in Rando Phantom Undergoing CT of the Head

    International Nuclear Information System (INIS)

    The aim of this study is to assess the dose reduction of eye lens and availability of bismuth garments resulting from the use of radioprotective bismuth garments to shield the eyes of patients undergoing head CT. Rando phantom and TLDs were used to determine the amount of dose reduction by bismuth shielding of the eye in the following simulated CT scans : (a) scanning of the head including orbits, (b) scanning of the whole head, and (c) angled scanning of the head excluding orbits. The average dose reduction of eye lens was 43.2%, 36.0% and 1.4% for the three CT scans listed above. Significant reduction in the eye lens dose was achieved by using superficial orbital bismuth shielding during head CT scans. However, bismuth shields should not be used for the patients when their eyes are excluded from the primarily exposed region.

  15. German pilot projects of mammography screening

    International Nuclear Information System (INIS)

    The carriers of the German Statutory Health Care System have recognized that only mammographic screening according to the European Guidelines for the Quality Assurance of Mammography Screening will permit early detection of breast cancer with an acceptable risk/benefit ratio. In the German pilot projects, regional mammography screening programmes according to the European guidelines are being tested in the framework of the German health care system. The European guidelines require comprehensive quality assurance of all relevant steps in the chain of events involved in screening, from invitation on to therapy and follow-up. Such comprehensive quality assurance involves several medical specialities and other professional groups dealing with out-patient and in-patient health care and requires long-term cooperation with public institutions (population registries, cancer registries). The objective of the pilot projects is to test the organizational and legal conditions essential to introduction of a mammographic screening programme according to the European quality assurance guidelines in Germany. (orig.)

  16. The German risk study. Pt. 2

    International Nuclear Information System (INIS)

    A severe nuclear power plant accident can be followed by a considerable release of radioactive effluents into the atmosphere. Due to atmospheric dispersion, areas of different sizes can be contaminated. The corresponding doses can cause early illnesses, early fatalities, latent effects and genetic effects. They are accompanied by economic effects. Within the consequence model of the German Risk Study, early and late fatalities and genetically significant doses are calculated. The calculations are based on real data or phenomena such as the population around 19, present or future German sites, or 115 real weather sequences, as well as on models such as an atmospheric dispersion model, a dose model, a model of protective actions or a health effects model. Within this lecture, the consequence model applied in the German Risk Study will be discussed in detail and the results will be presented. (orig./RW)

  17. Melting behaviour of lead and bismuth nano-particles in quasicrystalline matrix - The role of interfaces

    Indian Academy of Sciences (India)

    Alok Singh; A P Tsai

    2003-02-01

    Nanomaterials are playing an increasingly important role in modern technologies. Interfaces are crucial in nanotechnology. In this study, we have examined the stability of nanoparticles. Major emphasis is on understanding the effect of interfaces on melting. Melting behaviour of nanocrystalline interfaces, created by embedding lead and bismuth nanoparticles in quasicrystalline matrices, was studied. Sharply faceted and coherent interfaces can be related to sharper melting transitions, while irregularly shaped and incoherent interfaces can be directly correlated with lowering of melting temperatures. It is shown here that solid lead forms a high energy interface with phason strain-free quasicrystal (resulting in a lowering of the melting temperature) while bismuth forms a low energy interface with the quasicrystal (resulting in superheating, unusual for bismuth).

  18. Bismuth subcarbonate as filler particle for an Epoxy-based root canal sealer

    Directory of Open Access Journals (Sweden)

    Eduardo Schwartzer

    2013-01-01

    Full Text Available Introduction: The aim of this study was to evaluate the addition of bismuth subcarbonate with different concentrations regarding the rheological properties of an experimental epoxy-based root canal sealer. Materials and Methods: Endodontic sealers were prepared with epoxy resin-based sealer with bismuth subcarbonate additions of 20%, 40%, 60%, 80%, 100%, and 120%. Flow, film thickness, working time, setting time, dimensional change, sorption, solubility, and cytotoxicity were studied according to the ISO standards. Data were statistically analyzed by one-way ANOVA, and Tukey multiple comparisons were used, with a significance level of 5%. Results: The flow, working time, water sorption, and solubility significantly decreased and the film thickness and dimensional change increased with higher filler particle addition. There were no statistically significant differences for setting time and cytotoxicity between the filler particle proportions. Conclusion: Experimental resin-based sealer with bismuth subcarbonate addition up to 40% can be an alternative for root canal sealer.

  19. Fluorescence Emission Centres and the Corresponding Infrared Fluorescence Saturation in a Bismuth-Doped Silica Fibre

    Institute of Scientific and Technical Information of China (English)

    QIU Yan-Qing; SHEN Yong-Hang

    2008-01-01

    We investigate the fluorescence characteristics of bismuth doped silica fibres with and without Al co-dopant which are fabricated by means of modified chemical vapour deposition (MCVD) technique, and find that the fluorescences in the red region (centred around 750nm) and in the infrared region (centred around 1100nm) may originate from different emission sites in the fibre. Strong upconversion phenomena are observed in both Al-codoped and non Al codoped bismuth fibres when the fibres are excited by an acoustic-optic Q-switched Nd: YVO4 laser. Both the aspects indicate that the upper energy level absorption reported in the work of the bismuth doped silica fibre lasers may result from the fluorescence emission sites that are not responsible for the infrared emission. It is thus expected that optimizing the compositions and the fabrication conditions of the fibre and then transferring more fluorescence emission centres are helpful for the infrared emission.

  20. Sintering characteristics of La/Nd doped Bi4Ti3O12 bismuth titanate ceramics

    Directory of Open Access Journals (Sweden)

    Islam Aminul Md.

    2015-01-01

    Full Text Available A good understanding about the properties of La/Nd doped Bismuth Titanate (BIT ceramics at high temperature is very important as the new materials being developed based on the BIT. Pure BIT, La doped (BLT, Nd doped (BNT and La and Nd co-doped BIT (BLNT powders were synthesized by solid state reaction method. Prepared powders were calcined at different temperatures and structural properties measured by XRD. For pure BIT better crystal quality was obtained at 750 0C and for both BLT and BNT better result obtained at 800 0C. Calcined powders were formed into pellets and sintered at different temperatures and its dielectric properties were characterized. Optimum sintering temperature for both BLT and BNT showed was 850 0C and La and Nd co-doped bismuth titanate (BLNT revealed optimum sintering temperature of 950 0C. Therefore, optimum sintering temperature of bismuth titanate was increased due to La and Nd doping.

  1. Bismuth- and lithium-loaded plastic scintillators for gamma and neutron detection

    International Nuclear Information System (INIS)

    Transparent plastic scintillators based on polyvinyltoluene (PVT) have been fabricated with high loading of bismuth carboxylates for gamma spectroscopy, and with lithium carboxylates for neutron detection. When activated with a combination of standard fluors, 2,5-diphenyloxazole (PPO) and tetraphenylbutadiene (TPB), gamma light yields with 15 wt% bismuth tripivalate of 5000 Ph/MeV are measured. A PVT plastic formulation including 30 wt% lithium pivalate and 30 wt% PPO offers both pulse shape discrimination, and a neutron capture peak at ~400 keVee. In another configuration, a bismuth-loaded PVT plastic is coated with ZnS(6Li) paint, permitting simultaneous gamma and neutron detection via pulse shape discrimination with a figure-of-merit of 3.8, while offering gamma spectroscopy with energy resolution of R(662 keV)=15%

  2. Bismuth- and lithium-loaded plastic scintillators for gamma and neutron detection

    Energy Technology Data Exchange (ETDEWEB)

    Cherepy, Nerine J., E-mail: cherepy1@llnl.gov [Lawrence Livermore National Laboratory, Livermore, CA (United States); Sanner, Robert D.; Beck, Patrick R.; Swanberg, Erik L.; Tillotson, Thomas M.; Payne, Stephen A. [Lawrence Livermore National Laboratory, Livermore, CA (United States); Hurlbut, Charles R. [Eljen Technology, Sweetwater, TX (United States)

    2015-04-01

    Transparent plastic scintillators based on polyvinyltoluene (PVT) have been fabricated with high loading of bismuth carboxylates for gamma spectroscopy, and with lithium carboxylates for neutron detection. When activated with a combination of standard fluors, 2,5-diphenyloxazole (PPO) and tetraphenylbutadiene (TPB), gamma light yields with 15 wt% bismuth tripivalate of 5000 Ph/MeV are measured. A PVT plastic formulation including 30 wt% lithium pivalate and 30 wt% PPO offers both pulse shape discrimination, and a neutron capture peak at ~400 keVee. In another configuration, a bismuth-loaded PVT plastic is coated with ZnS({sup 6}Li) paint, permitting simultaneous gamma and neutron detection via pulse shape discrimination with a figure-of-merit of 3.8, while offering gamma spectroscopy with energy resolution of R(662 keV)=15%.

  3. Design of an Actinide Burning, Lead-Bismuth Cooled Reactor That Produces Low Cost Electricity

    Energy Technology Data Exchange (ETDEWEB)

    C. Davis; S. Herring; P. MacDonald; K. McCarthy; V. Shah; K. Weaver (INEEL); J. Buongiorno; R. Ballinger; K. Doyoung; M. Driscoll; P. Hejzler; M. Kazimi; N. Todreas (MIT)

    1999-07-01

    The purpose of this project is to investigate the suitability of lead-bismuth cooled fast reactors for producing low-cost electricity as well as for actinide burning. The goal is to identify and analyze the key technical issues in core neutronics, materials, thermal-hydraulics, fuels, and economics associated with the development of this reactor concept. The choice of lead-bismuth for the reactor coolant is an actinide burning fast reactor offers enhanced safety and reliability. The advantages of lead-bismuth over sodium as a coolant are related to the following material characteristics: chemical inertness with air and water; higher atomic number; lower vapor pressure at operating temperatures; and higher boiling temperature. Given the status of the field, it was agreed that the focus of this investigation in the first two years will be on the assessment of approaches to optimize core and plant arrangements in order to provide maximum safety and economic potential in this type of reactor.

  4. Poisoning effect of bismuth on modification behaviour of strontium in LM25 alloy

    Indian Academy of Sciences (India)

    S Farahany; A Ourdjini; M H Idris; L T Thai

    2011-10-01

    Nucleation and growth, temperature measurements andmicrostructure observations of silicon phase are presented for strontium modified Al–7%Si (LM25) cast alloy treated with bismuth. The results show that addition of bismuth in strontium modified alloys may have a poisoning effect resulting in lost modification of the silicon phase. With increasing Bi/Sr ratio, thermal analysis measurements showed that the eutectic growth temperature increased remarkably to 573°C and recalescence decreased to 0.2°C and the morphology of silicon displayed the same flakelike structure as in the unmodified alloys. Microstructural observation showed that a minimum Bi/Sr ratio of 1.2 which is equivalent to a Sr/Bi ratio of 0.43 is required for effective strontium modification and neutralization of the poisoning effect of bismuth.

  5. Preparation of bismuth-based nanosheets by ultrasound-assisted liquid laser ablation

    Science.gov (United States)

    Escobar-Alarcón, L.; Velarde Granados, E.; Solís-Casados, D. A.; Olea-Mejía, O.; Espinosa-Pesqueira, M.; Haro-Poniatowski, E.

    2016-04-01

    The preparation of bismuth nanosheets ablating a high purity Bi target immersed in water subjected to an ultrasound wave is reported. The effect of the laser fluence used for ablation on the size and shape of the nanostructures synthesized was investigated. The obtained results reveal the formation of nanosheets with square-like shape and sizes from approximately 140-543 nm. In comparison, experiments without the ultrasound field lead to the formation of quasi-spherical nanoparticles. The nanosheets were characterized by means of transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS), UV-Vis and Raman spectroscopies. The bismuth nanosheets, as deposited, are highly crystalline, and depending on the preparation conditions, the α or β phases of Bi2O3 are obtained. UV-Vis measurements show the typical band absorption characteristic of bismuth with nanometric size. Raman spectra confirm the formation of Bi2O3 nanostructures.

  6. Application of Thermodynamic Calculations to the Pyro-refining Process for Production of High Purity Bismuth

    Science.gov (United States)

    Mezbahul-Islam, Mohammad; Belanger, Frederic; Chartrand, Patrice; Jung, In-Ho; Coursol, Pascal

    2016-04-01

    The present work has been performed with the aim to optimize the existing process for the production of high purity bismuth (99.999 pct). A thermo-chemical database including most of the probable impurities of bismuth (Bi-X, X = Ag, Au, Al, Ca, Cu, Fe, Mg, Mn, Na, Ni, Pb, S, Sb, Sn, Si, Te, Zn) has been constructed to perform different thermodynamic calculations required for the refining process. Thermodynamic description for eight of the selected binaries, Bi-Ca, Cu, Mn, Ni, Pb, S, Sb, and Sn, has been given in the current paper. Using the current database, different thermodynamic calculations have been performed to explain the steps involved in the bismuth refining process.

  7. Characteristics of polonium contamination from neutral irradiated lead-bismuth eutectic

    International Nuclear Information System (INIS)

    After neutron capture, bismuth-209 changes to polonium-210 that emits α-particles. Lead-Bismuth eutectic (LBE) in reactor system contaminates the system by polonium. We analyzed adsorbed materials from melted LBE on quartz glass plate. Lead, bismuth and their oxides were confirmed in adsorbed materials. And, we evaluated the baking method in vacuum for removal of polonium and adsorbed materials on quartz glass plate. It was evaluated that it is possible to remove almost all the polonium from the quartz glass plate by baking at temperature more than 300 C. degrees. Unfolding method was applied to calculate polonium distribution in LBE ingot. From measured α-particle pulse height distribution, the polonium distribution in depth of LBE ingot was calculated using quadratic programming code, where response functions are calculated by Monte Carlo method. (authors)

  8. Radioactive Iodine (I-129) Gas Adsorption by Using Bismuth-Embedded SBA-15

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Jae Hwan; Cho, Yong-Jun; Park, Jang Jin; Ahn, Do-Hee [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Yim, Man-Sung [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

    2015-05-15

    The efficient capture of the long-lived I-129, released as off-gas from nuclear fuel reprocessing, have been of significant concern in the waste management field. In this study, bismuth-embedded SBA-15 mesoporous silica was firstly applied for iodine capture and storage. SBA-15 was functionalized with thiol (-SH) groups, followed by bismuth adsorption with Bi-S bonding, which was thermally treated to form Bi{sub 2}S{sub 3} within SBA-15. The bismuth-embedded SBA-15s demonstrated high iodine loading capacities with 540 mg-I/g-sorbent maximally, which benefitted from the high surface area and porosity of SBA-15 as well as the formation of thermodynamically stable BiI{sub 3} compound. Iodine physisorption could effectively be suppressed due to the large pores present in SBA-15, resulting in chemisorption as a main mechanism for iodine confinement.

  9. Influence of bismuth on the charging ability of negative plates in lead-acid batteries

    Science.gov (United States)

    Lam, L. T.; Ceylan, H.; Haigh, N. P.; Manders, J. E.

    To examine the influence of bismuth on the charging ability of negative plates in lead-acid batteries, plates are made from three types of oxides: (i) leady oxide of high quality which contains virtually no bismuth (termed 'control oxide'); (ii) control oxide in which bismuth oxide is blended at bismuth levels from 0.01 to 0.12 wt.%; (iii) leady oxide produced from Pasminco VRLA Refined™ lead (0.05-0.06 wt.%Bi). An experimental tool—the 'conversion indicator'—is developed to assess the charging ability of the test negative plates when cycling under either zero percent state-of-charge (SoC)/full-charge or partial state-of-charge (PSoC) duty. Although the conversion indicator is not the true charging efficiency, the two parameters have a close relationship, namely, the higher the conversion indicator, the greater the charging efficiency. Little difference is found in the charging ability, irrespective of bismuth content and discharge rate, when the plates are subjected to zero percent SoC/full-charge duty; the conversion indicator lies in the range 81-84%. By contrast, there is a marked difference when the negative plates are subjected to PSoC duty, i.e. consecutive cycling through 90-60, 70-40, 80-40 and 90-40% SoC windows. Up to 0.06 wt.%Bi improves the charging ability, especially with a low and narrow PSoC window (40-70% SoC) of the type that will be experienced in 42 V powernet automobile and hybrid electric duties. To maximize this beneficial effect, bismuth must be distributed uniformly in the plates. This is best achieved by using VRLA Refined™ lead for oxide production.

  10. Syntheses, crystal structures and characterizations of two new bismuth(III) arsenites

    International Nuclear Information System (INIS)

    Two new bismuth arsenites with two different structural types, namely, Bi2O(AsO3)Cl (1), Bi8O6(AsO3)2(AsO4)2 (2), have been synthesized by the solid-state reactions. Compound 1 exhibits novel 2D bismuth arsenite layers with Bi4O4 rings capped by oxide anions, which are further interconnected by Bi–Cl–Bi bridges into a 3D network. Compound 2 contains both arsenite and arsenate anions, its 3D structures are based on 1D bismuth arsenite and 1D bismuth arsenate chains both along b-axis, which are interconnected by oxide anions via Bi–O–Bi bridges, forming 1D tunnels of Bi4As4 8-membered rings (MRs) along b-axis, the lone pairs of the arsenite groups are orientated toward the centers of the above tunnels. Thermogravimetric analysis indicated that both compounds display high thermal stability. Optical property measurements revealed that they are wide band-gap semiconductors. Both compounds display broad green-light emission bands centered at 506 nm under excitation at 380 and 388 nm. - Graphical abstract: Solid state reactions of Bi2O3 (BiCl3) and As2O3 yielded two new compounds with two different structural types, namely, Bi2O(AsO3)Cl (1), Bi8O6(AsO3)2(AsO4)2 (2). They represent the first examples of bismuth arsenates. Highlights: ► Solid state reactions of Bi2O3 (BiCl3) and As2O3 yielded two new phases. ► They represent the first examples of bismuth arsenites. ► The two compounds exhibit two different structural types.

  11. The effect of bismuth subcitrate in patients with diarrhea predominant irritable bowel syndrome

    Directory of Open Access Journals (Sweden)

    Kalani M

    2010-09-01

    Full Text Available "nBackground: The irritable bowel syndrome (IBS is one of the most common chronic medical conditions. Various mechanisms, including altered gut flora and/or small bowel bacterial overgrowth, have been suggested to play a role in the development of gas-related symptoms aim of study. The clinical evidence of small intestinal bacterial overgrowth as an important etiology of irritable bowel syndrome continues to accumulate. Clinical symptoms of bacterial overgrowth and irritable bowel syndrome are similar; however, a definitive cause-and-effect relationship remains unproven. It is unclear whether motility dysfunction causes bacterial overgrowth or gas products of"nenteric bacteria affect intestinal motility in irritable bowel syndrome."n "nMethods: In a randomized double-blind placebo-controlled trial consisting of treatment with bismuth subcitrate. Primary efficacy variable was subjective symptoms; frequency of abdominal pain, Number of bowel movement & Bloating/distension."n "nResults: 119 patients were enrolled (59 bismuth subcitrate and 60 placebo recipients. At the end of phase 2, all symptom scores dropped significantly both in bismuth subcitrate and placebo group (p<0.001. There was not a significant difference in symptom relief with bismuth subcitrate versus placebo administration."n "nConclusions: There was not a significant difference in symptom relief with bismuth subcitrate versus placebo in IBS patients. Whether antibiotics can improve quality of life in patients with irritable bowel syndrome warrants further research."nInterventions: Participants were randomly assigned to receive 120mg bismuth subcitrate four times daily for 14 days (n=59 or placebo (n=60.

  12. Basic principles of lead and lead-bismuth eutectic application in blanket of fusion reactors

    International Nuclear Information System (INIS)

    High magnetohydrodynamic pressure drop is an important issue for liquid metal blanket concepts. To decrease magnetohydrodynamic resistance authors propose to form insulating coatings on internal surface of blanket ducts at any moment of fusion reactor exploitation. It may be achieved easily if lead or lead-bismuth eutectic is used and technology of oxidative potential handling is applied. A number of experiments carried out in NNSTU show the availability of the proposed technology. It bases on formation of the insulating coatings that consist of the oxides of components of the structural materials and of the coolant components. In-situ value of the insulating coatings characteristics ρδ is ∼ 10-5 Ohm·m2 for steels and 5,0x10-6 - 5,0x10-5 Ohm·m2 for vanadium alloys. Thermal cycling is possible during exploitation of a blanket. The experimental research of the insulating coatings properties during thermal cycling have shown that the coatings formed into the lead and lead-bismuth coolants save there insulating properties. Experience of many years is an undoubted advantage of the lead-bismuth coolant and less of the lead coolant in comparison with lithium. Russian Federation possesses of experience of exploitation of the research and industrial facilities, of experience of creation of the pumps, steamgenerators and equipment with heavy liquid metal coolants. The unique experience of designing, assembling and exploitation of the fission reactors with lead-bismuth coolant is also available. The problem of technology of lead and lead-bismuth coolants for power high temperature radioactive facilities has been solved. Accidents, emergency situations such as leakage of steamgenerators or depressurization of gas system in facilities with lead and lead-bismuth coolants have been explored and suppressed. (author)

  13. Level 2 PRA for a German BWR

    International Nuclear Information System (INIS)

    A concept for a Level 2 Probabilistic Risk Assessment (L2 PRA) for a German Boiling Water Reactor (BWR) has been developed taking into account the role of L2 PRA within the German regulatory landscape. According to this concept, a plant specific evaluation of the severe accident phenomenology as well as analyses of the accident progression for the severe accident scenarios has been performed. Furthermore a plant specific MELCOR 1.8.6 model has been developed and special MELCOR source term calculations have been performed for the different release paths. This paper will present examples from the different areas described above. (author)

  14. Structure of the German electricity industry

    International Nuclear Information System (INIS)

    The German integrated association is a union of those electric power supply utilities in the Federal Republic of Germany which cooperate in the integrated operation of 220 kV and 380 kV. The German integrated association (DVG) was founded in 1948. Its main task is to create the technical, operational and legal conditions for the cooperation in the national and international integrated system. The inclusion of the new Federal States has been practiced for the first time with the 320 MW power station in Offleben. (DG)

  15. The German heritage in Balkan languages

    Directory of Open Access Journals (Sweden)

    Helmut Wilhelm Schaller

    2015-09-01

    Full Text Available The German heritage in Balkan languagesAll Balkan languages show some German elements in their vocabulary, beginning with Old Bulgarian Bible texts up to modern Balkan languages, including Bulgarian, Macedonian, Serbian, Albanian, Romanian and Modern Greek. Etymologies of Balkan words and German words must be distinguished. Loanwords in Balkan languages are confined to words which are traceable back to Germanic languages, e. g. Gothic, Old and Middle High German and contemporary German. Not only the word store but also onomastics were occasionally influenced by German languages, but it is not possible to speak of a German substrat or adstrat in the way we can speak of a Thracian or Illyrian substrat, or Greek or Romance adstrat. Dziedzictwo germańskie w językach bałkańskichW słownictwie każdego z języków bałkańskich występują pewne germańskie elementy, poczynając od starobułgarskich tekstów biblijnych, a kończąc na współczesnych językach bałkańskich, jakimi są: bułgarski, macedoński, serbski, albański, rumuński i nowogrecki. W badaniach nad etymologią należy wyraźnie rozgraniczać dwa nurty rozwojowe: germański i bałkański. Katalog zapożyczeń ograniczamy do wyrazów obecnych w językach bałkańskich, których etymologię możemy prześledzić wstecz do gockiego, staro- i środkowo-wysoko-niemieckiego oraz współczesnego niemieckiego. Nie tylko słownictwo, lecz także onomastyka wykazują okazjonalnie wpływy niemieckie, jednak w żadnym razie nie ma podstaw, by mówić o germańskim substracie czy adstracie w takim sensie, w jakim mówimy o substracie trackim czy iliryjskim, bądź adstracie romańskim lub greckim.

  16. German energy policy in deregulated Europe

    International Nuclear Information System (INIS)

    The author argues in favor of a more fact-oriented German energy policy: Firstly, German energy policy must accept the new European framework of a market economy. This means that German utilities must no longer be burdened with the implementation of political objectives. The German power industry needs a level playing field for competition on a European scale. Consequently, also the European partner countries should not limit themselves to the minimum conditions of the Single Market Directive in opening their markets. Secondly, German energy policy must develop new forms of cooperation with the power industry so as to maintain domestic employment and the addition of value despite considerably stronger competitive pressure. Also the conflicting targets of sustainability, continuity of supply, and economic viability must not only be discussed, but must be turned into productive approaches. Thirdly, this means that there must be no inadmissible solution in matters nuclear. If the German power industry is to remain strong, in the interest of domestic jobs and opportunities for the future, it must not lose any more domestic market share to other European companies. Fourthly, we need a new energy policy which takes cognizance of the results of market development in a more rational, less emotional way. In this respect, it should be limited henceforth to supporting renewable energies and technologies so as to enhance energy efficiency in line with market requirements. Fifthly, German energy policy must not commit the mistake of enforcing deregulation and, at the same time, exempting large segments of the market from competition. Thus, the planned expansion of renewable energies, and the increase in cogeneration to more than thirty percent of the German electricty generation, by way of quotas and revenues for electricity from these sources fed into the public grid, are incompatible with competition in Europe. The electricity tax within the framework of the eco tax, the

  17. Testing the Lexical Competence of German in Slovak-German and German(Austrian-Czech/Slovak Adolescent Bilinguals

    Directory of Open Access Journals (Sweden)

    Pallay Jozef

    2014-06-01

    Full Text Available The paper builds on our previous work in the field of bilingual education and/ or the process of natural bilingualisation of Slovak-German bilinguals in Slovak educational diasporas (educational islands in Austria. Starting point of psycholinguistic testing based on classic American Peabody Picture Vocabulary Test ( PPVT -III in its revised and German version presented in this paper is the thesis of initial lagging behind of linguistic (lexical, grammatical competence level of language L2 of bilingual children from preschool age in relation to various sociolinguistic variables, which, however, with age may, under certain favourable conditions nearly equal competence of monolinguals and in the area of reception of language even exceed it. For testing the reception levels of German mental lexicon we used two approximately equally large groups of respondents in a bilingual secondary grammar school in Bratislava and Vienna. The hypothesis of our research was that bilingual Austrian-Czech/Slovak bilinguals from Austria would achieve significantly better results than the Slovak-German bilinguals from Slovakia. The test results, however, surprisingly disproved our hypothesis and want to contribute to the debate on setting minimum standards of language competence of bilinguals as well as on optimisation of conditions of bilingual or monolingual education of not only Slovaks abroad.

  18. Deposition of Visible Light Active Photocatalytic Bismuth Molybdate Thin Films by Reactive Magnetron Sputtering

    OpenAIRE

    Marina Ratova; Kelly, Peter J; Glen T. West; Xiaohong Xia; Yun Gao

    2016-01-01

    Bismuth molybdate thin films were deposited by reactive magnetron co-sputtering from two metallic targets in an argon/oxygen atmosphere, reportedly for the first time. Energy dispersive X-ray spectroscopy (EDX) analysis showed that the ratio of bismuth to molybdenum in the coatings can be effectively controlled by varying the power applied to each target. Deposited coatings were annealed in air at 673 K for 30 min. The crystalline structure was assessed by means of Raman spectroscopy and X-ra...

  19. Equilibrium distribution of lanthanum, neodymium, and thorium between lithium chloride melt and liquid bismuth

    Science.gov (United States)

    Zagnit'ko, A. V.; Ignat'ev, V. V.

    2013-04-01

    The distribution of lanthanum, neodymium, and thorium between a lithium chloride melt and liquid bismuth with additions of lithium as a reducing agent are investigated at 650°C. Equilibrium values of their distribution constants are measured. It is shown that in contrast to neodymium and lanthanum, thorium cannot be extracted from bismuth into lithium chloride. This allows us to propose an efficient scheme for separating lanthanides and thorium in a system for the extraction of fuel salts in molten-salt nuclear reactors.

  20. Basic principles of lead and lead-bismuth eutectic application in blanket of fusion reactors

    International Nuclear Information System (INIS)

    Full text: One of the main requirements of advanced nuclear-power engineering is inherent safety of power installations. It initiates R and D of heavy liquid metals (lead, lead- bismuth eutectic) application in fission reactors as substitute of sodium. The same requirement makes advisable R and D of the lead and lead-bismuth eutectic application in blanket of fusion reactors as substitute of lithium. High magnetohydrodynamic pressure drop is an important issue for liquid metal blanket concepts. To decrease MHD-resistance authors propose to form electro-insulating coatings on internal surface of blanket ducts at any moment of fusion reactor exploitation. It may be achieved easily if lead or lead-bismuth eutectic is used and technology of oxidative potential handling is applied. A number of experiments carried out in NNSTU show the availability of the proposed technology. It bases on formation of the insulating coatings that consist of the oxides of components of the structural materials and of the coolant components. In-situ value of the electro-insulating coatings characteristics rd (r - specific resistance of coatings, d - thickness) is ∼ 10-5Ω·m2 for steels and 5, 0x10-6 - 5, 0x10-5Ω·m2 for vanadium alloys. Thermal cycling is possible during exploitation of a blanket. The experimental research of the insulating coatings properties during thermal cycling have shown that the coatings formed into the lead and lead-bismuth coolants save there electro-insulating properties. Experience of many years is an undoubted advantage of the lead-bismuth coolant and less of the lead coolant in comparison with lithium. Russian Federation possesses of experience of exploitation of the research and industrial facilities, of experience of creation of the pumps, steam generators and another equipment with heavy liquid metal coolants. The unique experience of designing, assembling and exploitation of the fission reactors with lead-bismuth coolant is also available. The problem

  1. Optical properties of thermally reduced bismuth-doped sodium aluminosilicate glasses

    DEFF Research Database (Denmark)

    Nielsen, K.H.; Smedskjær, Morten Mattrup; Yue, Yuanzheng;

    Heat-treatment of multivalent ion containing glasses in a hydrogen atmosphere may cause both reduction of the multivalent ions and ionic inward diffusion, resulting in improved glass properties. Bismuth-doped glasses are also interesting objects not only concerning the reduction induced diffusion......, but also concerning the metal particle formation, and the broadband near infrared luminescence. Both the inward diffusion and the infrared luminescence depend on the bismuth oxidation state. The latter can be varied by adjusting the parameters of the heat-treatment, e.g., time, temperature, and...

  2. Electrical properties of niobium doped barium bismuth-titanate ceramics

    International Nuclear Information System (INIS)

    Highlights: ► Pure and doped BaBi4Ti4O15 were prepared via the solid-state reaction method. ► The grain size was suppressed in Nb-doped samples. ► The diffuseness of the dielectric peak increased with dopant concentration. ► Niobium affected on relaxor behavior of barium bismuth titanate ceramics. ► The conductivity change was noticed in doped samples. -- Abstract: BaBi4Ti4–5/4xNbxO15 (BBNTx, x = 0, 0.05, 0.15, 0.30) ceramics have been prepared by solid state method. XRD data indicate the formation of single-phase-layered perovskites for all compositions. SEM micrographs suggest that the grain size decreases with Nb doping. The effect of niobium doping on the dielectric and relaxor behavior of BaBi4Ti4O15 ceramics was investigated in a wide range of temperatures (20–777 °C) and frequencies (1.21 kHz to 1 MHz). Nb doping influences Tc decrease as well as the decrease of dielectric permittivity at Curie temperature. At room temperature, undoped BaBi4Ti4O15 exhibits dielectric constant of ∼204 at 100 kHz, that slightly increases with Nb doping. The conductivity of BBNT5 ceramics is found to be lower than that of other investigated compositions. The value of activation energy of σDC was found to be 0.89 eV, 1.01 eV, 0.93 eV and 0.71 eV for BBT, BBNT5, BBNT15 and BBNT30, respectively.

  3. Electrical properties of niobium doped barium bismuth-titanate ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Bobić, J.D., E-mail: jelenabobic@yahoo.com [Institute for Multidisciplinary Researches, Belgrade University, Kneza Viseslava 1, Belgrade (Serbia); Vijatović Petrović, M.M. [Institute for Multidisciplinary Researches, Belgrade University, Kneza Viseslava 1, Belgrade (Serbia); Banys, J. [Faculty of Physics, Vilnius University, 9 Sauletekio Str., Vilnius (Lithuania); Stojanović, B.D. [Institute for Multidisciplinary Researches, Belgrade University, Kneza Viseslava 1, Belgrade (Serbia)

    2012-08-15

    Highlights: ► Pure and doped BaBi{sub 4}Ti{sub 4}O{sub 15} were prepared via the solid-state reaction method. ► The grain size was suppressed in Nb-doped samples. ► The diffuseness of the dielectric peak increased with dopant concentration. ► Niobium affected on relaxor behavior of barium bismuth titanate ceramics. ► The conductivity change was noticed in doped samples. -- Abstract: BaBi{sub 4}Ti{sub 4–5/4x}Nb{sub x}O{sub 15} (BBNTx, x = 0, 0.05, 0.15, 0.30) ceramics have been prepared by solid state method. XRD data indicate the formation of single-phase-layered perovskites for all compositions. SEM micrographs suggest that the grain size decreases with Nb doping. The effect of niobium doping on the dielectric and relaxor behavior of BaBi{sub 4}Ti{sub 4}O{sub 15} ceramics was investigated in a wide range of temperatures (20–777 °C) and frequencies (1.21 kHz to 1 MHz). Nb doping influences T{sub c} decrease as well as the decrease of dielectric permittivity at Curie temperature. At room temperature, undoped BaBi{sub 4}Ti{sub 4}O{sub 15} exhibits dielectric constant of ∼204 at 100 kHz, that slightly increases with Nb doping. The conductivity of BBNT5 ceramics is found to be lower than that of other investigated compositions. The value of activation energy of σ{sub DC} was found to be 0.89 eV, 1.01 eV, 0.93 eV and 0.71 eV for BBT, BBNT5, BBNT15 and BBNT30, respectively.

  4. Formic acid oxidation at platinum-bismuth catalysts

    Directory of Open Access Journals (Sweden)

    Popović Ksenija Đ.

    2015-01-01

    Full Text Available The field of heterogeneous catalysis, specifically catalysis on bimetallic surfaces, has seen many advances over the past few decades. Bimetallic catalysts, which often show electronic and chemical properties that are distinct from those of their parent metals, offer the opportunity to obtain new catalysts with enhanced selectivity, activity, and stability. The oxidation of formic acid is of permanent interest as a model reaction for the mechanistic understanding of the electrooxidation of small organic molecules and because of its technical relevance for fuel cell applications. Platinum is one of the most commonly used catalysts for this reaction, despite the fact that it shows a few significant disadvantages: high cost and extreme susceptibility to poisoning by CO. To solve this problem, several approaches have been used, but generally, they all consist in the modification of platinum with a second element. Especially, bismuth has received significant attention as Pt modifier. According to the results presented in this survey dealing with the effects influencing the formic acid oxidation it was found that two types of Pt-Bi bimetallic catalysts (bulk and low loading deposits on GC showed superior catalytic activity in terms of the lower onset potential and oxidation current density, as well as exceptional stability compared to Pt. The findings in this report are important for the understanding of mechanism of formic acid electrooxidation on a bulk alloy and decorated surface, for the development of advanced anode catalysts for direct formic acid fuel cells, as well as for the synthesis of novel low-loading bimetallic catalysts. The use of bimetallic compounds as the anode catalysts is an effective solution to overcoming the problems of the formic acid oxidation current stability for long term applications. In the future, the tolerance of both CO poisoning and electrochemical leaching should be considered as the key factors in the development

  5. China as A Growing Strategic Market for German Business

    Institute of Scientific and Technical Information of China (English)

    Zhu Zijun

    2011-01-01

    @@ German Companies view China as a more strategically important market, despite their concerns over China's regulatory environment, according to a re-port from the German Chamber of Commerce in China.

  6. The 101 translation problems between Japanese and German/English

    OpenAIRE

    Fujinami, Tsutomu; Nanz, Christine

    1997-01-01

    We investigate differences between Japanese and German/English and explain characteristic phenomena to Japanese. The study helps us to realize what can be problematic when translating Japanese into German/English and vice versa.

  7. Tense and Agreement in German Agrammatism

    Science.gov (United States)

    Wenzlaff, Michaela; Clahsen, Harald

    2004-01-01

    This study presents results from sentence-completion and grammaticality-judgment tasks with 7 German-speaking agrammatic aphasics and 7 age-matched control subjects examining tense and subject-verb agreement marking. For both experimental tasks, we found that the aphasics achieved high correctness scores for agreement, while tense marking was…

  8. Analysis on the German Functionalist Translation Theory

    Institute of Scientific and Technical Information of China (English)

    LI Ying

    2013-01-01

    German functionalist approach makes considerable contributions to translation studies for considering translation as an fact of intercultural communication and concentrate on the purpose and function of the target text. It distinctively promoted translation theory against the traditional translation views. The paper analyzes its main ideas ,contribution and criticism of the Ger⁃man Functionalist Translation Theory.

  9. Lombard speech database for German language

    OpenAIRE

    Soloducha, Michal; Raake, Alexander; Kettler, Frank; Voigt, Peter

    2016-01-01

    This is a publication of Lombard speech database for German language. Additionally, a GitHub project has been created where information about database updates and related data will be stored: https://github.com/Telecommunication-Telemedia-Assessment/Lombard-Speech-database.git

  10. The Legislator and the German University

    Science.gov (United States)

    Hennis, Wilhelm

    1977-01-01

    Changes in German higher education stemming from student uprisings in the late 1960's are reviewed with focus on recent legislative regulations and general state-institution relationships. Issues considered include personnel and financial administration, founding of new universities, militancy, and access. (LBH)

  11. Michael Sadler and the German Connection.

    Science.gov (United States)

    Higginson, J. H.

    1990-01-01

    Chronicles works of Michael Sadler who compared British and German educational systems, emphasizing Germany's contributions in technical education. Presents Sadler's 1912 recommendations--eight lessons premised upon powerful centralized government's ability to implement policy. Reflects on how World War I and Nazism influenced Sadler's thought and…

  12. Phocine Distemper in German Seals, 2002

    OpenAIRE

    Müller, Gundi; Wohlsein, Peter; Beineke, Andreas; Haas, Ludwig; Greiser-Wilke, Irene; Siebert, Ursula; Fonfara, Sonja; Harder, Timm; Stede, Michael; Achim D Gruber; Baumgärtner, Wolfgang.

    2004-01-01

    Approximately 21,700 seals died during a morbillivirus epidemic in northwestern Europe in 2002. Phocine distemper virus 1 was isolated from seals in German waters. The sequence of the P gene showed 97% identity with the Dutch virus isolated in 1988. There was 100% identity with the Dutch isolate from 2002 and a single nucleotide mismatch with the Danish isolate.

  13. German Academic Libraries: Tradition and Change.

    Science.gov (United States)

    Bunzel, Jurgen; Poll, Roswitha

    2002-01-01

    Describes academic libraries in Germany and how they have been influenced by restructuring and reforming the higher education system, changes in information technology and information industry, and effects of the German reunification process. Discusses library resources, including staff, buildings, and collections; catalogs; preservation; user…

  14. Dengue Antibody Prevalence in German Travelers

    OpenAIRE

    Wichmann, Ole; Lauschke, Annekathrin; Frank, Christina; Shu, Pei-Yun; Niedrig, Matthias; Huang, Jyh-Hsiung; Stark, Klaus; Jelinek, Tomas

    2005-01-01

    We studied 2,259 German citizens after they returned from dengue-endemic countries from 1996 to 2004. Serotype-specific dengue antibodies indicated acute infections in 51 (4.7%) travelers with recent fever and 13 (1.1%) travelers with no recent fever, depending largely on destination and epidemic activity in the countries visited.

  15. Gifted Education in German-Speaking Countries

    Science.gov (United States)

    Herrmann, Anna; Nevo, Baruch

    2011-01-01

    The purpose of this article is to provide the reader with a comprehensive yet detailed account of the current giftedness and gifted education situation in Austria, Germany, and Switzerland. It is concerned with four main research questions: (1) How is "giftedness" defined in German-speaking countries? (2) How are gifted children identified? (3)…

  16. Roots and Rogues in German Child Language

    Science.gov (United States)

    Duffield, Nigel

    2008-01-01

    This article is concerned with the proper characterization of subject omission at a particular stage in German child language. It focuses on post-verbal null subjects in finite clauses, here termed Rogues. It is argued that the statistically significant presence of Rogues, in conjunction with their distinct developmental profile, speaks against a…

  17. Vygotsky, Consciousness, and the German Psycholinguistic Tradition

    Science.gov (United States)

    Leitch, David G.

    2011-01-01

    This article argues that Vygotsky's choice of word meaning as the basic unit of analysis for cultural psychology connects him to a German psycholinguistic tradition--exemplified in the work of G. W. F. Hegel and J. G. Herder--distinct from the Marxist tradition. While later commentators criticize Vygotsky's reliance on word meaning, arguing that…

  18. Balancing energy in the German market design

    OpenAIRE

    Möller, Christoph

    2010-01-01

    Among electricity marketplaces balancing energy takes a central role in mediating the supply and demand equilibrium. This thesis analyzes strategies employed in the balancing energy market, as well as their implications for other marketplaces in the setting of the German electricity market.

  19. Gifted Education in German-Speaking Europe

    Science.gov (United States)

    Ziegler, Albert; Stoeger, Heidrun; Harder, Bettina; Balestrini, Daniel Patrick

    2013-01-01

    The authors first briefly describe how the concepts of talents and giftedness found in German-speaking Europe have evolved in the school system and in general over the past two centuries, and how the variety of gifted-education efforts found within and beyond schools as well as counseling efforts attest to these changes. They then discuss four…

  20. German and Russian Adolescents' Environmental Awareness.

    Science.gov (United States)

    Szagun, Gisela; Pavlov, Vladimir I.

    German (n=610) and Russian (n=610) adolescents in 3 age groups, 12, 15, and 18 years, were given a questionnaire assessing their feelings towards environmental destruction, their readiness for pro-environmental action, and their ethical attitude toward nature. In both nationalities anxiety, sadness, and anger about environmental destruction were…

  1. DIMA – Annotation guidelines for German intonation

    DEFF Research Database (Denmark)

    Kügler, Frank; Smolibocki, Bernadett; Arnold, Denis;

    2015-01-01

    easier since German intonation is currently annotated according to different models. To this end, we aim to provide guidelines that are easy to learn. The guidelines were evaluated running an inter-annotator reliability study on three different speech styles (read speech, monologue and dialogue...

  2. Using Projects to Teach Professional German

    OpenAIRE

    Hager, Michael

    2010-01-01

    The article demonstrates the use of projects in the teaching of business German in a third-year college course. First, background information about implementing projects in foreign language instruction will be discussed. Next, concrete examples of how this can be done using the textbook Deutsch im Berufsalltag will be provided. Finally, students’ reactions to using projects in this course will be supplied.

  3. How to Find Out in: German.

    Science.gov (United States)

    Flower, Clara K.

    This library handbook is an informal guide for the student studying the German language and literature. It lists reference materials basic to general research and gives their locations in the Fogler Library at the University of Maine. Reference works for study of the language include (1) dictionaries and encyclopedias, (2) histories of the…

  4. Dictionary of chemistry. English/German

    International Nuclear Information System (INIS)

    This English/German dictionary covers more than 100.000 terms from chemistry, chemical engineering and related fields. It also contains molecular formulas, as well as numerous synonyms and areas of application. IUPAC terminology is emphasized, and outdated or rare terminology is indicated. (MM)

  5. Content, Joseph Schwab and German "Didaktik"

    Science.gov (United States)

    Deng, Zongyi

    2015-01-01

    This article attempts to extend and deepen the conversation concerning the knowledge-based approach to curriculum espoused by Michael Young in his 2013 "JCS" paper through revisiting the structure of the disciplines thinking of Joseph Schwab and German "Didaktik." It argues that curriculum making requires a theory of knowledge…

  6. Who can become German? Xenophobia and Attitudes Towards Naturalization

    OpenAIRE

    Diehl, Claudia; Tucci, Ingrid

    2011-01-01

    International audience Germans are opening up to the topic of immigration: According to the representative data of this report, less and less Germans without a migration background feel threatened by immigration. Also, their attitude towards naturalization has changed. The question “What is the decisive factor for granting German nationality?” is now answered differently than in the 1990s. A significant part of the population without migration background considers ethnic German descent as ...

  7. Analysis of the first Romanian-German economic relations

    OpenAIRE

    FLEISCHER Wiegand Helmut

    2013-01-01

    The first Romanian-German economic relations were initiated by the German colonists who had settled on the territory of Transylvania since the 12th century. Over the centuries, the Romanian- German economic relations had some fluctuations, but the tradition of these relations is indisputable. The fluctuations in the Romanian-German economic relations were caused by the economic evolution in Romania and Germany, the politic relations between the two states as well as the European political and...

  8. LATVIA AS A TOURISM DESTINATION FOR GERMAN TOURISTS

    OpenAIRE

    Blatt, Benjamin

    2015-01-01

    The German source market offers a high potential for the Latvian tourism industry. This paper provides an analysis of the German outgoing tourism which allows evaluating how good the Latvian tourism market can satisfy the needs of the German outgoing tourists. This research study assesses the conformity between the needs of German travellers and the Latvian tourism offers. The methods used in this research study are as follows: evaluation and analysis of surveys, content analysis, graphical a...

  9. The perception of the fehmarnbelt connection among german stakeholders

    DEFF Research Database (Denmark)

    Lohse, Sandrina; Jespersen, Per Homann

    This report gives an overview of the planned improvements of the German hinterland infrastructure connected to the fixed Fehmarn Belt Link (FBL), as well as the views of the key German stake holders towards the FBL.......This report gives an overview of the planned improvements of the German hinterland infrastructure connected to the fixed Fehmarn Belt Link (FBL), as well as the views of the key German stake holders towards the FBL....

  10. Anaphoric Resolution and Text Comprehension for Readers of German.

    Science.gov (United States)

    Berkemeyer, Victoria C.

    1994-01-01

    This study examines whether readers of German can identify correctly the coreferents of anaphoric expressions in a German text and whether this ability is related to their overall comprehension of the text and their baseline German language ability. Findings reveal a positive relationship between the ability to resolve anaphoric references and…

  11. Turkey and Turks in the German media

    Directory of Open Access Journals (Sweden)

    Necla Mora

    2009-10-01

    Full Text Available It is known that the prejudices, which have emerged in the historical process, are engraved in the social memory of the nations; conveyed from the past to the future in language, art, literature, history and many other fields; and reproduced via media especially in the periods of crisis.Firstly, Turkish-German relations must be examined in the historical process in order to understand how Turkey and Turks are represented in the German media. Accordingly, Turkish-German relations are also important in terms of drawing a general framework on how the West, which has been preserving its topicality for centuries, sees Turkey.How the subjects and groups are represented in the media texts and what kind of an image are formed in relation with them reveals the social memory of the countries in which the media texts are produced.The prejudices which have emerged in the social memory of the German people in the historical process have an effect in forming the negative image of Turks by being reproduced via active media especially in the periods of crisis. A negative image of Turks is brought forward with the concepts such as human rights violations, fundamentalism, oppression against the women and the minorities, Kurdish-Turkish discrimination and Alawi-Sunni discrimination.German media uses as evidence and tries to emphasize their justness on the publications, photographs and images that take place in the Turkish media in terms of especially the concepts mentioned above.Media texts are dialogues which are formed between the target audience and the narrator who reflects the opinions of the authority elites that are the sources of news. For that reason, representation forms of Turkey and Turks will be associated with the historical prejudices and analyzed with the critical discourse analysis approach in the scope of this study.

  12. Sprechen sie deutsch? German language and revitalization of ethnic identity of the Germans in Bačka

    OpenAIRE

    Krel Aleksandar

    2012-01-01

    This paper? analyzes the use of German langue in the public and private spheres of communication among members of three local associations of Germans in Bačka. Their efforts to preserve native idiom, after decades of "ethnic mimicry" of German community in Vojvodina, and under the hardship of asymmetrical bilingualism favoring Serbian and Hungarian languages, are directed not only to preserve German language, but they also play a significant role in the process of (re) construction of t...

  13. Potentiation of the action of metronidazole on Helicobacter pylori by omeprazole and bismuth subcitrate

    DEFF Research Database (Denmark)

    Andersen, L P; Colding, H; Kristiansen, J E

    2000-01-01

    regimens that include proton pump inhibitors. In the present study, the synergistic effect of subinhibitory concentrations (0.25-0.5 MIC) of either bismuth subcitrate or omeprazole with metronidazole on the susceptibility of 42 H. pylori strains was investigated by agar dilution method and the Epsilometer...

  14. Robust synthesis of bismuth titanate pyrochlore nanorods and their photocatalytic applications.

    Science.gov (United States)

    Murugesan, Sankaran; Subramanian, Vaidyanathan Ravi

    2009-09-14

    A facile and template-free reverse micelle-based method can be employed to synthesize highly crystalline and pure stoichiometric bismuth titanate (Bi(2)Ti(2)O(7)) pyrochlore nanorods 400-500 nm long and 40-50 nm in diameter which demonstrate promising photoactivity. PMID:20448962

  15. Effect of bismuth citrate, lactose, and organic acid on necrotic enteritis in broilers

    Science.gov (United States)

    Clostridium perfringens – associated necrotic enteritis causes significant losses and increased morbidity in poultry. The objective of this study was to evaluate the effect of bismuth citrate and acidifiers on the development of necrotic enteritis in broilers. The first study was a dose response t...

  16. Examination of dielectric dispersion of complex oxides on the basis of bismuth-containing titanates

    International Nuclear Information System (INIS)

    In the present work the samples of complex oxide compounds on the basis of bismuth titanates with chalcolamprite structure type and layered perovskite doped with Cr, Fe and Co were studied at room temperature by the method of dielectric spectroscopy in the frequency range of 30 to 106 Hz

  17. Azo dyes photobleaching and operando FTIR study of acetaldehyde photoinduced decomposition on bismuth doped titania

    Czech Academy of Sciences Publication Activity Database

    Henych, Jiří; Štengl, Václav; Mattsson, A.; Österlund, L.

    Thessaloniki: Aristotle University of Thessaloniki, 2014, 41 PC-2-4. [European Meeting on Solar Chemistry and Photocatalysis: Environmental Applications (SPEA) /8./. Thessaloniki (GR), 25.6.2014-28.6.2014] Institutional support: RVO:61388980 Keywords : bismuth doped titania * photocatalytic Subject RIV: CA - Inorganic Chemistry

  18. Renal pigmentation due to chronic bismuth administration in a rhesus macaque (Macaca mulatta).

    Science.gov (United States)

    Johnson, A L; Blaine, E T; Lewis, A D

    2015-05-01

    Renal pigmentation due to the administration of exogenous compounds is an uncommon finding in most species. This report describes renal pigmentation and intranuclear inclusions of the proximal convoluted tubules due to chronic bismuth administration in a rhesus macaque. An 11-year-old Indian-origin rhesus macaque with a medical history of chronic intermittent vomiting had been treated with bismuth subsalicylate, famotidine, and omeprazole singly or in combination over the course of 8 years. At necropsy, the renal cortices were diffusely dark green to black. Light and electron microscopy revealed intranuclear inclusions within the majority of renal proximal tubular epithelial cells. These inclusions appeared magenta to brown when stained with hematoxylin and eosin and were negative by the Ziehl-Neelsen acid-fast stain. Elemental analysis performed on frozen kidney measured bismuth levels to be markedly elevated at 110.6 ppm, approximately 500 to 1000 times acceptable limits. To our knowledge, this is the first report of renal bismuth deposition in a rhesus macaque resulting in renal pigmentation and intranuclear inclusions. PMID:24990482

  19. A sensitive fluorescence quenching method for determination of bismuth with tiron

    International Nuclear Information System (INIS)

    We describe a fluorescence quenching method for determination of bismuth with tiron. The method is based on the reaction of tiron by bismuth(III) in acidic media. The influence of variables such as the pH, type of buffer, tiron concentration, reaction time and temperature were investigated. Under optimized conditions, the fluorescence quenching extent is proportional to the concentration of bismuth for Bi–tiron system at the range 0.13–2.09 μg mL−1 and the detection limit is 0.05 μg mL−1. The proposed sensor presented good repeatability, evaluated in terms of relative standard deviation (R.S.D.=±0.498%) for 11 replicates. This sensitive, rapid and accurate method has been successfully applied to the determination of trace bismuth(III) in water and hair samples and certified reference materials. -- Highlights: • No previous paper report on use of fluorescence quenching for determination of Bi. • Fluorescence quenching of trion is a sensitive method for determination of Bi(III). • Under the optimum conditions the detection limit is very low (0.05 μg mL−1). • The procedure is simple and safe and has high tolerance limit to interferences

  20. Dynamics and coherent control of high-amplitude optical phonons in bismuth

    Science.gov (United States)

    Decamp, M. F.; Reis, D. A.; Bucksbaum, P. H.; Merlin, R.

    2001-09-01

    High-amplitude optical phonons in bismuth are generated through impulsive stimulated Raman scattering and detected through the induced change in the optical reflectivity. Reflectivity changes greater than 1% have been recorded. Phonon dynamics and coherent control in the high-amplitude regime are reported.

  1. Microwave-assisted facile and rapid Friedel-Crafts benzoylation of arenes catalysed by bismuth trifluoromethanesulfonate

    DEFF Research Database (Denmark)

    Tran, Phoung Hoang; Hansen, Poul Erik; Pham, Thuy Than;

    2014-01-01

    The catalytic activity of metal triflates was investigated in Friedel–Crafts benzoylation under microwave irradiation. Friedel–Crafts benzoylation with benzoyl chloride of a variety of arenes containing electron-rich and electron-poor rings using bismuth triflate under microwave irradiation is...

  2. Nanodomains and nanometer-scale disorder in multiferroic bismuth ferrite single crystals

    Czech Academy of Sciences Publication Activity Database

    Jia, C.L.; Jin, L.; Wang, D.; Mi, S.B.; Alexe, M.; Hesse, D.; Reichlová, Helena; Martí, Xavier; Bellaiche, L.; Urban, K.W.

    2015-01-01

    Roč. 82, Jan (2015), s. 356-368. ISSN 1359-6454 Institutional support: RVO:68378271 Keywords : bismuth ferrite * crystal growth * high-resolution electron microscopy * atomic structure * first-principles calculations Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 4.465, year: 2014

  3. Group III-nitride thin films grown using MBE and bismuth

    Science.gov (United States)

    Kisielowski, Christian K.; Rubin, Michael

    2000-01-01

    The present invention comprises growing gallium nitride films in the presence of bismuth using MBE at temperatures of about 1000 K or less. The present invention further comprises the gallium nitride films fabricated using the inventive fabrication method. The inventive films may be doped with magnesium or other dopants. The gallium nitride films were grown on sapphire substrates using a hollow anode Constricted Glow Discharge nitrogen plasma source. When bismuth was used as a surfactant, two-dimensional gallium nitride crystal sizes ranging between 10 .mu.m and 20 .mu.m were observed. This is 20 to 40 times larger than crystal sizes observed when GaN films were grown under similar circumstances but without bismuth. It is thought that the observed increase in crystal size is due bismuth inducing an increased surface diffusion coefficient for gallium. The calculated value of 4.7.times.10.sup.-7 cm.sup.2 /sec. reveals a virtual substrate temperature of 1258 K which is 260 degrees higher than the actual one.

  4. Determination of (111) ordered domains on platinum electrodes by irreversible adsorption of bismuth.

    Science.gov (United States)

    Rodríguez, Paramaconi; Solla-Gullón, José; Vidal-Iglesias, Francisco J; Herrero, Enrique; Aldaz, Antonio; Feliu, Juan M

    2005-08-15

    Irreversible adsorbed bismuth can be used to determine the fraction of (111) domains on a given platinum sample. On Pt(111) electrodes, the surface redox process of adsorbed bismuth takes place at 0.63 V in a well-defined peak. The behavior of this redox process on the Pt(111) vicinal surfaces indicates that the bismuth atoms involved in the redox process are only those deposited on the (111) terrace sites and that the charge under the peak at 0.63 V is directly proportional to the number of sites on (111) ordered domains (terraces). The good linear relationship obtained between the charge for the bismuth redox process and the number of (111) terrace sites on the vicinal surfaces allows construction of a calibration curve. This calibration curve has been used to directly estimate the amount of (111) ordered domain terrace sites on polycrystalline platinum samples with different surface ordered domains. The results agree with what we would expect from our knowledge of these surfaces. PMID:16097774

  5. Microwave and magneto-optic properties of bismuth-substituted yttrium iron garnet thin films

    Science.gov (United States)

    Butler, J. C.; Kramer, J. J.; Esman, R. D.; Craig, A. E.; Lee, J. N.; Ryuo, T.

    1990-05-01

    Microwave and magneto-optic measurements have been made on bismuth-substituted yttrium iron garnet (BiYIG) films. Forward-volume (FV) magnetostatic-wave (MSW) attenuation has been measured from ferrimagnetic resonance and from pulse delay data. We report the indirect observation of FV MSW in BiYIG using two independent techniques: a pulse transmission technique and a passband measurement technique. Faraday rotation in the films was also recorded at a wavelength of 1.3 μm. The bismuth-substituted films are grown on carefully cleaned substrates and have yttrium:bismuth ratios of 1:1. The composition of the bismuth substituted films is Y1.5Bi1.5Fe5O12 deduced from lattice parameters and absolute Faraday rotation. These films show particular promise for use in waveguide-type high-speed MSW-optical devices where low MSW attenuation and high Faraday rotation are among the necessary criteria for successful operation.

  6. The antimicrobial effects and metabolomic footprinting of carboxyl-capped bismuth nanoparticles against Helicobacter pylori.

    Science.gov (United States)

    Nazari, P; Dowlatabadi-Bazaz, R; Mofid, M R; Pourmand, M R; Daryani, N E; Faramarzi, M A; Sepehrizadeh, Z; Shahverdi, A R

    2014-01-01

    Organic salts of bismuth are currently used as antimicrobial agents against Helicobacter pylori. This study evaluated the antibacterial effect of elemental bismuth nanoparticles (Bi NPs) using a serial agar dilution method for the first time against different clinical isolates and a standard strain of H. pylori. The Bi NPs were biologically prepared and purified by a recently described method and subjected to further characterization by infrared spectroscopy and anti-H. pylori evaluation. Infrared spectroscopy results showed the presence of carboxyl functional groups on the surface of biogenic Bi NPs. These biogenic nanoparticles showed good antibacterial activity against all tested H. pylori strains. The resulting MICs varied between 60 and 100 μg/ml for clinical isolates of H. pylori and H. pylori (ATCC 26695). The antibacterial effect of bismuth ions was also tested against all test strains. The antimicrobial effect of Bi ions was lower than antimicrobial effect of bismuth in the form of elemental NPs. The effect of Bi NPs on metabolomic footprinting of H. pylori was further evaluated by (1)H NMR spectroscopy. Exposure of H. pylori to an inhibitory concentration of Bi NPs (100 μg/ml) led to release of some metabolites such as acetate, formic acid, glutamate, valine, glycine, and uracil from bacteria into their supernatant. These findings confirm that these nanoparticles interfere with Krebs cycle, nucleotide, and amino acid metabolism and shows anti-H. pylori activity. PMID:24104691

  7. Bio-assisted synthesis and characterization of nanostructured bismuth (III) sulphide using Clostridium acetobutylicum

    International Nuclear Information System (INIS)

    Nanostructured bismuth (III) sulphide is synthesized at room temperature using a hydrogen sulphide producing microorganism namely Clostridium acetobutylicum. On contrary to chemical routes involving both the high and room temperature methods, the present experimental procedure involves a bio-assisted approach. This method is free from the usage of toxic and hazardous chemicals making it an environment friendly route. The synthesized bismuth sulphide is characterized using transmission electron microscope (TEM), powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry (CV). From our experiments we find that bismuth sulphide produced using this bio-assisted approach exhibits a hexagonal shaped plate-like structures and is stabilized by the extracellular proteins present in the culture medium. - Graphical abstract: A green chemistry approach towards the synthesis of bismuth (III) sulphide nanostructures at room temperature using a hydrogen sulphide producing microorganism namely, Clostridium acetobutylicum is demonstrated. - Highlights: • Environmentally benign (greener) route towards synthesis of Bi2S3 nanostructures. • Bio-assisted synthesis of Bi2S3 at room temperature using Clostridium acetobutylicum. • Extracellular proteins in H2S producing microorganism as stabilizer for Bi2S3 NPs. • Hexagonal platelets of Bi2S3 possessing an orthorhombic crystalline structure

  8. Electrodeposition of bismuth telluride nanowires with controlled composition in polycarbonate membranes

    International Nuclear Information System (INIS)

    Bismuth telluride nanowires were potentiostatically deposited from a water/DMSO 50%, v/v electrolyte within polycarbonate etched ion-track membranes covered by a platinum substrate. The presence of DMSO shifts the potentials to more negative values and slows down the cation diffusion. Cyclic voltammetries on recessed Pt nanoelectrodes using polycarbonate membranes highlight a complex electrochemical behavior through several cathodic and anodic peaks which are not observed onto platinum discs macroelectrodes. Analytical investigations enabled the determination of appropriate deposition conditions to finely tune the average composition of the nanowires. Calibrated TEM-EDX analyses evidence high aspect ratio nanowires, whose composition is strongly dependent on the deposition potential. In the same manner as for bismuth telluride film electroplating, bismuth enrichment occurs at more cathodic deposition potential whereas tellurium enrichment is observed at low cathodic potentials. Stoichiometric nanowires of 60 nm diameter were obtained at −100 mV vs Ag/AgCl from an electrolyte which contains [Bi3+] = 1.5[HTeO2+] = 15 mM. The composition is homogeneous along the nanowire except at both edges: the cap is rich in bismuth whereas the base is rich in tellurium. The composition at the nanowire base is adjusted by setting a short initial voltage step (Ui = −300 mV vs Ag/AgCl, ti = 2 s). In the case of stoichiometric compounds, the resulting nanostructures were found to be polycrystalline with a preferential orientation along the direction perpendicular to the planes (0 1 5).

  9. Electrodeposition of bismuth telluride thermoelectric films from a nonaqueous electrolyte using ethylene glycol

    NARCIS (Netherlands)

    Nguyen, H.P.; Wu, M.; Su, J.; Vullers, R.J.M.; Vereecken, P.M.; Fransaer, J.

    2012-01-01

    Ethylene glycol was studied as an electrolyte for the electrodeposition of thermoelectric bismuth telluride films by cyclic voltammetry, rotating ring disk electrode and electrochemical quartz crystal microbalance (EQCM). The reduction of both Bi3+ and Te4+ ions proceeds in one step without the form

  10. Structural Engineering of Vacancy Defected Bismuth Tellurides for Thermo-electric Applications

    Directory of Open Access Journals (Sweden)

    Chumakov Y.

    2012-10-01

    Full Text Available Molecular Dynamics and ab-initio simulations are used to find the most stable stoichiometries of Bismuth Tellurides with vacancy defects. The interest is to decrease the thermal conductivity of these compounds a key point to achieve high figure of merits. A reduction of 70% of the thermal conductivity is observed with Te vacancies of only 5%.

  11. Bio-assisted synthesis and characterization of nanostructured bismuth (III) sulphide using Clostridium acetobutylicum

    Energy Technology Data Exchange (ETDEWEB)

    Kamaraj, Sathish Kumar; Venkatachalam, Ganesh; Arumugam, Palaniappan; Berchmans, Sheela, E-mail: sheelaberchmans@yahoo.com

    2014-02-14

    Nanostructured bismuth (III) sulphide is synthesized at room temperature using a hydrogen sulphide producing microorganism namely Clostridium acetobutylicum. On contrary to chemical routes involving both the high and room temperature methods, the present experimental procedure involves a bio-assisted approach. This method is free from the usage of toxic and hazardous chemicals making it an environment friendly route. The synthesized bismuth sulphide is characterized using transmission electron microscope (TEM), powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry (CV). From our experiments we find that bismuth sulphide produced using this bio-assisted approach exhibits a hexagonal shaped plate-like structures and is stabilized by the extracellular proteins present in the culture medium. - Graphical abstract: A green chemistry approach towards the synthesis of bismuth (III) sulphide nanostructures at room temperature using a hydrogen sulphide producing microorganism namely, Clostridium acetobutylicum is demonstrated. - Highlights: • Environmentally benign (greener) route towards synthesis of Bi{sub 2}S{sub 3} nanostructures. • Bio-assisted synthesis of Bi{sub 2}S{sub 3} at room temperature using Clostridium acetobutylicum. • Extracellular proteins in H{sub 2}S producing microorganism as stabilizer for Bi{sub 2}S{sub 3} NPs. • Hexagonal platelets of Bi{sub 2}S{sub 3} possessing an orthorhombic crystalline structure.

  12. Fridel-Crafts acylation using bismuth triflate in [BMI][PF6

    DEFF Research Database (Denmark)

    Tran, Phuong Hoang; Duus, Fritz; Le, Thach Ngoc

    2012-01-01

    Bismuth trifluoromethanesulfonate was found to be a good catalyst for the Friedel–Craftsacylation. Bismuthtriflate immobilized in an ionic liquid was the most efficient catalytic system. Bismuthtriflate in [BMI][PF6] catalyzes this reaction under microwave irradiation allowing the rapid synthesis...

  13. Thermodynamics of neptunium in LiCl-KCl eutectic/liquid bismuth systems

    International Nuclear Information System (INIS)

    Thermodynamic properties of neptunium in LiCl-KCl eutectic/liquid bismuth systems in the temperature range 400--500 C have been studied using a galvanic cell method for the pyrometallurgical reprocessing of nuclear spent fuels. The standard potential of the Np/Np(III) couple vs. the Ag/AgCl (1 wt% AgCl) reference electrode in LiCl-KCl eutectic was measured and given by the equation ENp/Np(III)0 = minus2.0667 + 0.0007892 T (σ = 0.0009), where E is in volts, T is in kelvin, and σ is the standard deviation. The potential of neptunium-bismuth alloy, ENp-Bi, was measured as a function of neptunium concentration, XNpinBi. The curves for EBi-Np vs. log XNpinBi indicated the neptunium solubility in liquid bismuth to be 0.34 ± 0.02, 0.61 ± 0.08, and 1.06 ± 0.09 (±σ) atom % at 400, 450, and 500 C, respectively. The excess partial free energy of neptunium in liquid bismuth was represented by the equation, Δbar GNpxs (kcal/g atom) = minus32.5 (±0.7) + 0.0072 (±0.0010) T. The values of the solubility and excess partial free energy for neptunium were closer to those for plutonium rather than uranium

  14. Optimal biliary drainage for inoperable Klatskin's tumor based on Bismuth type

    OpenAIRE

    Lee, Sang Hyub; Park, Joo Kyung; Yoon, Won Jae; Lee, Jun Kyu; Ryu, Ji Kon; Yoon, Yong Bum; Kim, Yong-Tae

    2007-01-01

    AIM: To investigate differences in the effects of biliary drainage procedures in patients with inoperable Klatskin’s tumor based on Bismuth type, considering endoscopic retrograde biliary drainage (ERBD), external percutaneous transhepatic biliary drainage (EPTBD) and internal biliary stenting via the PTBD tract (IPTBD).

  15. [The Germans from Hungary in the German Federal Republic. Impacts of the banishment on policy, the economy, and culture].

    Science.gov (United States)

    Eberl, I

    1993-01-01

    The ethnic composition of the population of the former German Federal Republic is analyzed, with a focus on the numbers of Germans who emigrated from Hungary after World War II. Consideration is given to political factors behind the migration of ethnic Germans, and the effects of this migration on politics, economy, and social life in the Federal Republic of Germany. PMID:12158120

  16. Hall Plateaus at magic angles in ultraquantum Bismuth

    Science.gov (United States)

    Benoît, Fauqué.

    2009-03-01

    The behaviour of a three-dimensional electron gas in the presence of a magnetic field strong enough to put all carriers in the first Landau level (i.e. beyond the quantum limit) is a longstanding question of theoretical condensed matter physics [1]. This issue has been recently explored by two high-field experiments on elemental semi-metal Bismuth. In a first study of transport coefficients (which are dominated by hole-like carriers), the Nernst coefficient presented three unexpected maxima that are concomitant with quasi-plateaux in the Hall coefficient [2]. In a second series of experiments, torque magnetometry (which mainly probes the three Dirac valley electron pockets) detected a field-induced phase transition [3]. The full understanding of the electron and hole behaviours above the quantum limit of pure Bi is therefore still under debate. In this talk, we will present our measurement of the Hall resistivity and torque magnetometry with magnetic field up to 31 T and rotating in the trigonal-bisectrix plane [4]. The Hall response is dominated by the hole pockets according to its sign as well as the period and the angular dependence of its quantum oscillations. In the vicinity of the quantum limit, it presents additional anomalies which are the fingerprints of the electron pockets. We found that for particular orientations of the magnetic field (namely ``magic angles''), the Hall response becomes field-independent within the experimental resolution around 20T. This drastic dependence of the plateaux on the field orientation provides strong constraints for theoretical scenarios. [4pt] [1] Bertrand I. Halperin, Japanese Journal of Applied Physics, 26, Supplement 26-3 (1987).[0pt] [2] Kamran Behnia, Luis Balicas, Yakov Kopelevich, Science, 317, 1729 (2008).[0pt] [3] Lu Li, J. G. Checkelsky, Y. S. Hor, C. Uher, A. F. Hebard, R. J. Cava, and N. P. Ong , Science, 321, 5888 (2008).[0pt] [4] Benoît Fauqu'e, Luis Balicas, Ilya Sheikin, Jean Paul Issi and Kamran Behnia

  17. Improvements to a Flow Sensor for Liquid Bismuth-Fed Hall Thrusters

    Science.gov (United States)

    Bonds, Kevin; Polzin, Kurt A.

    2010-01-01

    Recently, there has been significant interest in using bismuth metal as a propellant in Hall Thrusters [1, 2]. Bismuth offers some considerable cost, weight, and space savings over the traditional propellant--xenon. Quantifying the performance of liquid metal-fed Hall thrusters requires a very precise measure of the low propellant flow rates [1, 2]. The low flow rates (10 mg/sec) and the temperature at which free flowing liquid bismuth exists (above 300 C) preclude the use of off-the-shelf flow sensing equipment [3]. Therefore a new type of sensor is required. The hotspot bismuth flow sensor, described in Refs. [1-5] is designed to perform a flow rate measurement by measuring the velocity at which a thermal feature moves through a flow chamber. The mass flow rate can be determined from the time of flight of the thermal peak, [4, 5]. Previous research and testing has been concerned mainly with the generation of the thermal peak and it's subsequent detection. In this paper, we present design improvements to the sensor concept; and the results of testing conducted to verify the functionality of these improvements. A ceramic material is required for the sensor body (see Fig. 1), which must allow for active heating of the bismuth flow channel to keep the propellant in a liquid state. The material must be compatible with bismuth and must be bonded to conductive elements to allow for conduction of current into the liquid metal and measurement of the temperature in the flow. The new sensor requires fabrication techniques that will allow for a very small diameter flow chamber, which is required to produce useful measurements. Testing of various materials has revealed several that are potentially compatible with liquid bismuth. Of primary concern in the fabrication and testing of a robust, working prototype, is the compatibility of the selected materials with one another. Specifically, the thermal expansion rates of the materials relative to the ceramic body cannot expand so

  18. Laser spectroscopy of the ground-state hyperfine structure in H-like and Li-like bismuth

    International Nuclear Information System (INIS)

    The LIBELLE experiment performed at the experimental storage ring (ESR) at the GSI Helmholtz Center in Darmstadt aims for the determination of the ground state hyperfine (HFS) transitions and lifetimes in hydrogen-like (209Bi82+) and lithium-like (209Bi80+) bismuth. The study of HFS transitions in highly charged ions enables precision tests of QED in extreme electric and magnetic fields otherwise not attainable in laboratory experiments. While the HFS transition in H-like bismuth was already observed in earlier experiments at the ESR, the LIBELLE experiment succeeded for the first time to measure the HFS transition in Li-like bismuth in a laser spectroscopy experiment

  19. Synthesis and performance of bismuth trioxide nanoparticles for high energy gas generator use

    Energy Technology Data Exchange (ETDEWEB)

    Martirosyan, K S; Wang, L; Vicent, A; Luss, D, E-mail: kmartirossian@uh.ed [Department of Chemical and Biomolecular Engineering, University of Houston, Houston, TX 77204 (United States)

    2009-10-07

    Our experiments showed that the combustion of an Al-Bi{sub 2}O{sub 3} nanoparticle mixture generated the highest pressure pulse among common nanothermite reactions and can potentially be used as a nanoenergetic gas generator. The combustion front propagation velocity and rate of energy release increased by up to three orders of magnitude when the particle size was reduced to a nanosize range for both the aluminum and the oxidizer. We developed a novel one-step (metal nitrate-glycine) combustion synthesis of nanostructured amorphous-like and highly crystalline bismuth trioxide nanoparticles. The combustion synthesis was conducted using a solution of molten bismuth nitrate as an oxidizer and glycine as a fuel. The glycine was completely combusted during the thermal decomposition of the bismuth nitrate pentahydrate and generated a temperature front that propagated through the sample. Increasing the fuel concentration increased the maximum combustion temperature from 280 to 1200 {sup 0}C and the Bi{sub 2}O{sub 3} particle size from 20 to 100 nm. The oxidizer/fuel ratio had a strong impact on the bismuth trioxide particle crystallinity. At low temperature (280 {sup 0}C), amorphous-like bismuth trioxide nanoparticles formed, while at T{>=}370 {sup 0}C the structures were crystalline. A peak pressure of {approx}12 MPa and a thermal front propagating velocity of {approx}2500 m s{sup -1} were achieved during the combustion of an Al-Bi{sub 2}O{sub 3} mixture containing 80 wt% of the synthesized Bi{sub 2}O{sub 3} crystalline nanoparticles (size: 40-50 nm).

  20. Experience and results of MELCOR application for German PWRs

    International Nuclear Information System (INIS)

    An introduction into severe accident research work performed at GRS with regard to the use of the MELCOR code is given in Chapter One of the paper. Experience in applying MELCOR 1.8.3 for German PWRs and results of MELCOR calculations done within the project 'Accident management - Mitigation' for German LWRs are presented in Chapter Two. This 3-year project was finished February 1998. It was funded by the German Ministry for Environment, Nature Conservation and Nuclear Safety - BMU. In Chapter Three, a short overview of a training course on 'Phenomenology of Severe Accidents in PWR-Plants' is given. Mainly due to the interest from German NPPs GRS developed this special training session in 1996. Since 1996 it has been held several times for operators, shift personnel and the management board of two different German NPPs and for lecture of the German NPP training centre in Essen. In Chapter Four, results of the application of MELCOR 1.8.4 for German PWRs are presented. This work is done within a new project on 'Accident Management - Mitigation' for German LWRs. It was started in March 1998 and is again funded by the German Federal Ministry BMU. An objective of this project is to perform further MELCOR calculations, to be used within a PSA level 2 study for a German PWR, which is done at GRS in parallel. The experience of using MELCOR for German PWRs are summarised in Chapter Five. (author)

  1. Making sense of the German Wikipedia community

    Directory of Open Access Journals (Sweden)

    Rikke Frank Jørgensen

    2012-08-01

    Full Text Available This article presents the findings from a qualitative study of the German Wikipedia community, focusing on how people engaged with Wikipedia make sense of norms, collaborative practices and means of regulation within the community. The study highlights the strong focus on the quality of the end-product (the encyclopedia in the German community, stressing that article quality is seen as more important than the wiki-process as such. As the community has grown, an increasing number of rules and mechanisms have been deployed to resolve various issues and conflicts, however the interviewees do not perceive Wikipedia as being bureaucratic, but rather describe it as a “rule-governed anarchy”. The findings suggest that people contribute for a variety of reasons, yet point to reactions from and interactions with fellow Wikipedians as one of the strongest motivational drivers for participation.

  2. On the intonation of German intonation questions

    DEFF Research Database (Denmark)

    Petrone, Caterina; Niebuhr, Oliver

    2014-01-01

    German questions and statements are distinguished not only by lexical and syntactic but also by intonational means. This study revisits, for Northern Standard German, how questions are signalled intonationally in utterances that have neither lexical nor syntactic cues. Starting from natural...... productions of such 'intonation questions', two perception experiments were run. Experiment 1 is based on a gating paradigm, which was applied to naturally produced questions and statements. Experiment 11 includes two indirect-identification tasks. Resynthesized stimuli were judged in relation to two context...... to the intonational nucleus. Rather, listeners can refer to shape, slope, and alignment differences of the preceding prenuclear pitch accent to identify sentence mode. These findings are in line with studies suggesting that the utterance-final rise versus fall contrast is not directly related to sentence modality...

  3. Psychological training of German science astronauts

    Science.gov (United States)

    Manzey, Dietrich; Schiewe, Albrecht

    Although the significance of psychosocial issues of manned space flights has been discussed very often in recent literature, up to now, very few attempts have been made in North-America or Europe to provide astronaut candidates or spacecrew members with some kind of psychological training. As a first attempt in this field, a psychological training program for science astronauts is described, which has been developed by the German Aerospace Research Establishment and performed as part of the mission-independent biomedical training of the German astronauts' team. In contrast to other training concepts, this training program focused not only on skills needed to cope with psychosocial issues regarding long-term stays in space, but also on skills needed to cope with the different demands during the long pre-mission phase. Topics covered in the training were "Communication and Cooperation", "Stress-Management", "Coping with Operational Demands", "Effective Problem Solving in Groups", and "Problem-Oriented Team Supervision".

  4. German public opinion on admitting refugees

    OpenAIRE

    Gerhards, Jürgen; Hans, Silke; Schupp, Jürgen

    2016-01-01

    Since the beginning of 2016, the Socio-Economic Panel (SOEP) study has been conducting a monthly survey of German attitudes, expectations, and fears concerning migration. The third wave of the survey,-the Barometer of Public Opinion on Refugees in Germany (Stimmungsbarometer zu Geflüchteten in Deutschland)-, conductedin March 2016, shows that more than half of all respondents still associate the influx of refugees with more risks than opportunities. Nonetheless, a clear majority (81 percent o...

  5. Quo Vadis German Scholarly Communication in Economics?

    OpenAIRE

    Mazarakis, Athanasios; Peters, Isabella

    2015-01-01

    In this paper we study the situation of scholarly communication in Economics and Business Studies in Germany. We combine findings from an online survey, focus group interviews and a panel discussion. Some of the results of the survey are that economists at German universities and research institutes most frequently use the online encyclopedia Wikipedia, content sharing services, video and image hosting services as well as video conferencing systems. In a professional context, economists prima...

  6. Evaluating Automatic Detection of Misspellings in German

    OpenAIRE

    Anne Rimrott; Trude Heift

    2008-01-01

    his study investigates the performance of a spell checker designed for native writers on misspellings made by second language (L2) learners. It addresses two research questions: 1) What is the correction rate of a generic spell checker for L2 misspellings? 2) What factors influence the correction rate of a generic spell checker for L2 misspellings? To explore these questions, the study considers a corpus of 1,027 unique misspellings from 48 Anglophone learners of German and classifies these a...

  7. Treebank-based grammar acquisition for German

    OpenAIRE

    Rehbein, Ines

    2009-01-01

    Manual development of deep linguistic resources is time-consuming and costly and therefore often described as a bottleneck for traditional rule-based NLP. In my PhD thesis I present a treebank-based method for the automatic acquisition of LFG resources for German. The method automatically creates deep and rich linguistic presentations from labelled data (treebanks) and can be applied to large data sets. My research is based on and substantially extends previous work on automatically ac...

  8. Compensation and Incentives in German Corporations

    OpenAIRE

    Moritz Heimes; Steffen Seemann

    2011-01-01

    In this paper we analyze executive compensation in Germany for the period 2005-2009. We use a self-collected dataset on compensation arrangements in German corporations to estimate the impact of firm performance and firm risk on executive pay. To be in line with earlier studies in this literature, we first measure firm performance and firm risk based on stock market returns. Our findings support the prediction from agency theory that incentive pay decreases with firm risk. We find, however, t...

  9. Experiences with the new German Energy Act

    Energy Technology Data Exchange (ETDEWEB)

    Kraus, M. [Price Waterhouse Coopers, Berlin (Germany)

    1998-11-01

    The new German Energy Act has been in force since April this year, but competition has been slow to develop so far. New alliances and joint ventures are being formed to exploit the new freedoms that the Law brings, but the structures needed to operate competition are still being built. The question many are asking is whether an electricity exchange can bring the breakthrough? (Author)

  10. Can German wine cooperatives compete on quality?

    Directory of Open Access Journals (Sweden)

    Schamel Guenter H.

    2015-01-01

    Full Text Available The paper analyzes how German cooperative wineries compete with private (i.e. non-cooperative wineries regarding reputation, quality categorization and varietal selection. Among the reasons why German cooperatives lag behind in terms of reputation for quality wine are organization principles of cooperatives and the difficulty to manage growers supplying grapes of different qualities. Cooperatives turn their supply of grapes into wine often classified as quality wine without much distinction. Conversely, privately owned wineries growing their own grapes may have more control over quality along their production chain and are able to produce more distinctive wines. In turn, they gain more reputation with final consumers with respect to quality. We analyze data for private and cooperative wineries from Germany. Our objective is to identify key differences in terms of reputation for quality wine production. Specifically, we look at interaction effects based on organizational form (cooperative vs. private and the German wine quality categorization (i.e. basic quality wine vs. Kabinett, Spätlese, or Auslese as well as varietal effects. We employ a hedonic pricing model to test the hypothesis that wines produced by private producers receive a reputation premium relative to cooperatives. Moreover, we hypothesize that private wineries receive a price premium relative to coopera- tives for other than basic quality wines and distinct varieties such as Riesling and Pinot Noir. The empirical analysis confirms both hypotheses. The estimated coefficients indicate that cooperatives are unable to gain quality premium for most quality cat- egories and gain price premiums only for non-distinct varieties such as Lemberger and Dornfelder. We can argue that German cooperatives are stuck in the low quality corner of the quality and variety spectrum and are currently not able to compete with private wineries in terms of quality. This result supports the observation

  11. The United States Needs German Economic Leadership

    OpenAIRE

    Adam S. Posen

    2006-01-01

    Only together can the United States and Germany keep the global economy integrated--by removing agricultural roadblocks to a WTO deal, coordinating on relations with China, and securing the flow of international investment. The new German chancellor, Angela Merkel, could save the Doha Round by reinterpreting the budget deal just made on agricultural support funds at the EU summit, something US pleas and attempts to shame France cannot achieve. Both countries have an interest in making a commo...

  12. Assimilation and cohort effects for German immigrants

    OpenAIRE

    Gundel, Sebastian; Peters, Heiko

    2008-01-01

    Demographic change and the rising demand for highly qualified labor in Germany attracts notice to the analysis of immigration. In addition, the pattern of immigration changed markedly during the past decades. Therefore we use the latest data of the German Socioeconomic Panel up to the year 2006 in order to investigate the economic performance of immigrants. We perform regressions of three pooled cross sections (1986, 1996, 2006) to estimate assimilation and quality of immigrants as reflected ...

  13. Lessons learned from PSA's for German NPP's

    International Nuclear Information System (INIS)

    The results are discussed of Probabilistic Safety Analyses performed at German nuclear power plants: (i) Evaluating the well-balancedness of safety relevant system design; (ii) Deterministic safety requirements and plant safety level; (iii) Need for (and problems of) best-estimate analyses; (iv) Influence of dependent failures on system reliability; (v) Decision making based on PSAs. (J.B.) 2 tabs., 2 figs., 5 refs

  14. Optimal use of German Army maintenance resources

    OpenAIRE

    Wellbrink, Joerg

    1998-01-01

    Approved for public release; distribution is unlimited The German Army's maintenance branch has lost 25 percent of its soldiers since the end of the cold war. The maintenance branch has insufficient military personnel within maintenance units to maintain all combat unit equipment. The Army, therefore, purchases civilian man hours (mhrs) to satisfy some required maintenance. This thesis develops a mixed integer linear program, named ADOPT (administrative order optimizer), to optimally assig...

  15. The politics of the German company network

    OpenAIRE

    Höpner, Martin; Krempel, Lothar

    2003-01-01

    For over 100 years, the German company network was a major feature of organized corporate governance in Germany. This paper uses network visualization techniques and qualitative-historical analysis to discuss the structure, origins and development of this network and to analyze the reasons for its recent erosion. Network visualization makes it possible to identify crucial entanglement patterns that can be traced back historically. In three phases of network formation – the 1880s, 1920s and th...

  16. Topicalization in German, Czech and English

    Czech Academy of Sciences Publication Activity Database

    Štícha, František

    Madrid: Arco/Libros S.L, 2006 - (Geparde, F.; Ruis, G.; Gualda, V.), s. 2067-2077 ISBN 84-7635-632-3. [Análisis del discurso: Lengua , cultura, valores. Pamplona (ES), 01.11.2002] R&D Projects: GA ČR GA405/03/0377; GA ČR GA405/06/1057 Institutional research plan: CEZ:AV0Z9061902 Keywords : topicalization * comparative study * German * Czech * English Subject RIV: AI - Linguistics

  17. The Litvinenko Polonium-210 case - German experiences

    International Nuclear Information System (INIS)

    This paper brings together the measurement results taken and the lessons learned by the German Federal Office for Radiation Protection during the polonium-210 incident in Hamburg in late 2006. The incident was pivotal in confirming the importance of the defence against nuclear hazards in Germany and for highlighting the role of communication in the success of a deployment. The background of the case is reviewed and an overview of the German defence against nuclear hazards is given. The various measurement tasks, both at the scene and in the laboratory, and their results are summarized along with the communication challenges experienced. The main conclusions are that the traces of polonium-210 found at the sites were of little radiological consequence and the German defence against nuclear hazards in Germany delivered an excellent and measured response to the incident. However, communication challenges still exist and communication with the public and the emergency responders has to be given high priority during future deployments in order to ensure their success. (author)

  18. The Litvinenko polonium-210 case - German experiences

    International Nuclear Information System (INIS)

    This paper brings together the measurement results taken and the lessons learned by the German Federal Office for Radiation Protection during the polonium-210 incident in Hamburg in late 2006. The incident was pivotal in confirming the importance of the defence against nuclear hazards in Germany and for highlighting the role of communication in the success of a deployment. The background of the case is reviewed and an overview of the German defence against nuclear hazards is given. The various measurement tasks, both at the scene and in the laboratory, and their results are summarized along with the communication challenges experienced. The main conclusions are that the traces of polonium-210 found at the sites were of little radiological consequence and the German defence against nuclear hazards in Germany delivered an excellent and measured response to the incident. However, communication challenges still exist and communication with the public and the emergency responders has to be given high priority during future deployments in order to ensure their success. (author)

  19. Recovery potential of German sewage sludge ash.

    Science.gov (United States)

    Krüger, Oliver; Adam, Christian

    2015-11-01

    Incineration of sewage sludge is expected to increase in the future due to growing concerns about the direct use of sludge in agriculture. Sewage sludge is the pollutant sink of wastewater treatment and thus loaded with contaminants that might pose environmental hazards. Incineration degrades organic pollutants efficiently, but since the ash is currently mostly disposed of, all valuable component like phosphorus (P) and technologically relevant metals present in the sewage sludge ash (SSA) are removed from the economic cycle entirely. We conducted a complete survey of SSA from German mono-incineration facilities and determined the theoretical recovery potential of 57 elements. German SSA contains up to 19,000 t/a P which equals approximately 13% of phosphorus applied in the German agriculture in form of phosphate rock based mineral fertilizers. Thus, SSA is an important secondary resource of P. However, its P-solubility in ammonium citrate solution, an indicator for the bioavailability, is only about 26%. Treatment of SSA is recommended to enhance P bioavailability and remove heavy metals before it is applied as fertilizer. The recovery potential for technologically relevant metals is generally low, but some of these elements might be recovered efficiently in the course of P recovery exploiting synergies. PMID:25697389

  20. APPOSITIONS IN GERMAN AND IN TURKISH

    Directory of Open Access Journals (Sweden)

    Umut BALCI

    2012-03-01

    Full Text Available Turkish and German grammar books include word parts combined with secondary nouns. We call these, which exemplify the noun, as apposition. Turkish grammar books draw different conclusions from the term Apposition and it shows that it needs to be especially explicated. The apposition can be seen as resumption of same meaningful lexical units considered as a stylistic device providing a context-dependent credibility of expression, coherence, clarity, variation, adequacy and facility. We use many appositions consciously or unconsciously both in speaking and written language. When we compare the frequency of apposition usage with the relative clause, displaying the same function, apposition is surprisingly higher. According to statistical data, in every 100 sentences chosen from any text, there are about 30 appositions. Nevertheless, the apposition receives little attention especially in grammar teaching books, sometimes it even does not. Although it’s rare occurrence in the grammar books, we constantly encounter their syntactic, semantic and pragmatic dimensions in various types of texts. The reason why the Apposition in grammar teaching has received little discussionmight be a topic of other studies and we are not going to deal with this issue here. The purpose of this particular study is to reveal how much the Apposition is known as a grammatical category by our students and what can be done to increase the related awareness in this regard. Within the scope of this research study, the relative clauses present significance, as they are the most preferred and used ones among the Turkish learners who learn German as a foreign language. Due to their morphosyntactic structural difficulties, they are often memorized more than other forms of sentence. Moreover, they require more effort and in spoken form, they are economically impractical. However, it does not mean that theyarenotused or exaggerated in their usage because each mode of expression has

  1. The new German radiation protection ordinance

    International Nuclear Information System (INIS)

    According to European law, the Basic Safety Standards (BSS) published by the European Council in 1996 and the Council Directive on health protection of individuals against dangers of ionising radiation in relation to medical exposure had to be transferred into national law within due time. In 2001 the new Ordinance for the Implementation of the Euratom Guidelines on Radiation Protection] was published, which replaces the old Radiation Protection Ordinance. The new German Ordinance adapts the European Directive to German law, covering the general principles but even giving more details in many fields of radiation protection. The BSS scope certainly is much broader than the prescriptions important for the field of radiation protection in nuclear power plants. According to the scope of this workshop on occupational exposure in nuclear power plants - and as the BSS most probably will be quite familiar to all of you - after a short general overview on relevant contents of the German Ordinance, this presentation will focus on the main issues important in the operation of NPP and especially on some areas which may give rise to necessary changes caused by the new Ordinance. (A.L.B.)

  2. Interaction of oxygen vacancies in yttrium germanates

    KAUST Repository

    Wang, Hao

    2012-01-01

    Forming a good Ge/dielectric interface is important to improve the electron mobility of a Ge metal oxide semiconductor field-effect transistor. A thin yttrium germanate capping layer can improve the properties of the Ge/GeO 2 system. We employ electronic structure calculations to investigate the effect of oxygen vacancies in yttrium-doped GeO 2 and the yttrium germanates Y 2Ge 2O 7 and Y 2GeO 5. The calculated densities of states indicate that dangling bonds from oxygen vacancies introduce in-gap states, but the system remains insulating. However, yttrium-doped GeO 2 becomes metallic under oxygen deficiency. Y-doped GeO 2, Y 2Ge 2O 7 and Y 2GeO 5 are calculated to be oxygen substoichiometric under low Fermi energy conditions. The use of yttrium germanates is proposed as a way to effectively passivate the Ge/dielectric interface. This journal is © 2012 the Owner Societies.

  3. German Atomic Energy Act turns fifty

    International Nuclear Information System (INIS)

    The German Atomic Energy Act entered into force on January 1, 1960. It turns fifty at the beginning of 2010. Is this a reason to celebrate or rather the opposite? Lawyers, in principle, can view old pieces of legislation from 2 perspectives: On the one hand, aged laws are treated in a spirit of veneration and are celebrated as proven. On the other hand, an anniversary of this kind can be a welcome reason for demands to abolish or, at least, fundamentally renew that law. Over the past half century, the German Atomic Energy Act went through stormy and varied phases both of a legal and a political character. Its 50th anniversary is likely to spark off very conflicting evaluations as well. A review of legal history shows that the German or, rather, the Federal German Atomic Energy Act (AtG) was not a first-of-its-kind piece of legislation but stemmed from the 1957 EURATOM Treaty, in a way representing a latecomer of that treaty. The Atomic Energy Act experienced a number of important developments throughout its history: - In 1975, compulsory licensing of fuel element factories was introduced. - The back end of the fuel cycle, especially final storage, were incorporated in the Atomic Energy Act comprehensively first in 1976. - In 1985, legislators decided in favor of unlimited nuclear liability. - In 1994 and 1998, only some innovations in special items were introduced under the headings of environmental impact assessment and suitability for repository storage because the controversy about nuclear power did not permit a fundamental alignment towards a more comprehensive modern safety law. - The decision to opt out of the peaceful uses of nuclear power in 2002 drew the final line so far of decisions about directions of nuclear law in a major amendment. In parallel, the decisions by the Federal Constitutional Court and the Federal Administrative Court in the late 1970s and, above all, the 1980s provided important assistance which has remained valid to this day. What is

  4. ELECTRA: A European Lead-bismuth Cooled Training Reactor

    International Nuclear Information System (INIS)

    The lack of low power liquid metal cooled reactors has meant that few engineers within the nuclear power industry and research community are familiar with operational procedures of this family of coolants, expected to be used for Generation IV fast neutron systems. The reasons for this lack may include safety issues related to use of Mercury, NaK or sodium as applied in early low power reactors. Especially in western Europe, no low power liquid metal cooled reactor was ever in operation. Here, we present the design of a 2 MWth lead-bismuth cooled reactor with (Pu,Zr)N fuel, relying on natural convection for full power operation. The combination of low power density with natural convection for heat removal makes the reactor ideal for training purposes. The large thermal expansion of heavy liquid metals makes is possible to design low power fast neutron reactors relying on natural convection. Since at present, there exists no suitable material for pumps operating at high velocity in lead alloy environments, the only possible short term solution for constructing such a reactor is anyway to design for 100% natural circulation of the coolant. For this purpose, a small core height, a large difference between coolant inlet and outlet temperatures and a low coolant velocity is desired. By application of (Pu,Zr)N fuel, criticality can be achieved with a fissile inventory of 100 kg LWR grade plutonium. Monte Carlo simulations show that 19 hexagonal fuel assemblies, each with 91 fuel pins having an outer diameter of 1.1 cm, and an active height of 15 cm is sufficient to obtain a critical core. Including end pellets, gas plenum and end caps, the total core height is limited to 30 cm. Adopting P/D = 1.25 and a heat exchanger elevation of 4 m, it is found that 2 MW of thermal power may be removed by a natural circulation velocity of 0.4 m/s. This corresponds to a linear rating of 8 kW/m and a temperature increase of the coolant equal to 240 degrees. Limiting the clad temperature

  5. In vitro synergy testing of clarithromycin and 14-hydroxyclarithromycin with amoxicillin or bismuth subsalicylate against Helicobacter pylori.

    OpenAIRE

    Meyer, J.M.; Ryu, S; Pendland, S L; Danziger, L H

    1997-01-01

    The activity of clarithromycin-14-hydroxyclarithromycin (2:1 ratio) and bismuth subsalicylate or amoxicillin against Helicobacter pylori was determined by the checkerboard technique in vitro. Clarithromycin-14-hydroxyclarithromycin and amoxicillin resulted in additive effects in 7 of 22 isolates, compared to 14 of 22 isolates when bismuth subsalicylate was substituted for amoxicillin. Synergy was not demonstrated and is probably not responsible for the clinical success of treatment combinatio...

  6. Electrodes modified with bismuth, antimony and tin precursor compounds for electrochemical stripping analysis of trace metals (a short review)

    OpenAIRE

    Lezi, Nikolitsa; Economou, Anastasios; Barek, Jiří

    2014-01-01

    Over the last decade, intensive research is being carried out towards the development of “green” electrochemical sensors. Bismuth, antimony and tin electrodes have been proposed as potential substitutes of mercury electrodes in electrochemical stripping analysis of trace metals. The main advantage of these metals as electrode materials is their lower toxicity compared to mercury. Among the different configuration of bismuth, antimony and tin electrodes, one of the most attractive inv...

  7. Calculation of the two-electron vacuum-polarization corrections to the hyperfine splitting in Li-like bismuth

    International Nuclear Information System (INIS)

    Ab initio calculation of the two-electron vacuum-polarization corrections to the hyperfine splitting in Li-like bismuth is presented. The diagrams with electric and magnetic vacuum-polarization loops are evaluated rigorously to all orders in αZ. The accuracy of the theoretical prediction for the screened quantum electrodynamics contribution to the specific difference of the hyperfine splitting values of H- and Li-like bismuth is improved by a factor of 3. (paper)

  8. Learning from the Germans? History and Memory in German and European Discourses of Integration

    Directory of Open Access Journals (Sweden)

    Andrew Beattie

    2007-08-01

    Full Text Available History and memory appear to be increasingly important to discussions of European values and identity, as exemplified by references to ‘bitter experiences’ and ‘divided pasts’ in the draft EU constitution. The article takes recent suggestions that Europe could learn from German experiences of confronting multiple difficult pasts as its starting point, and considers critically what lessons those German experiences might in fact hold for ‘Europe’. It explores similarities and differences in the two integration contexts and their dominant approaches to, and assumptions about history and public memory. Specifically, it considers debates about the east-west division of the Cold War and about the place of communism and nazism in public memory. Contrary to common assumptions, the article argues that German experiences are not necessarily worth of European emulation.

  9. Pharmacokinetics and bioequivalence of ranitidine and bismuth derived from two compound preparations

    Institute of Scientific and Technical Information of China (English)

    Quan Zhou; Zou-Rong Ruan; Hong Yuan; Bo Jiang; Dong-Hang Xu

    2006-01-01

    AIM: To evaluate the bioequivalence of ranitidine and bismuth derived from two compound preparations.METHODS: The bioavailability was measured in 20healthy male Chinese volunteers following a single oral dose (equivalent to 200 mg of ranitidine and 220 mg of bismuth) of the test or reference products in the fasting state. Then blood samples were collected for 24 h.Plasma concentrations of ranitidine and bismuth were analyzed by high-performance liquid chromatography and inductively coupled plasma-mass spectrometry (ICPMS), respectively. The non-compartmental method was used for pharmacokinetic analysis. Log-transformed Cmax,AUC(0-t) and AUC(0-∞) were tested for bioequivalence using ANOVA and Schuirmann two-one sided t-test. Tmax was analyzed by Wilcoxon's test.RESULTS: Various pharmacokinetic parameters of ranitidine derived from the two compound preparations,including Cmax, AUC(0-t), AUC(0-∞), Tmax and T1/2, were nearly consistent with previous observations. These parameters derived from test and reference drug were as follows: Cmax(0.67 ± 0.21 vs 0.68 ± 0.22mg/L), AUC(0-t)(3.1 ± 0.6 vs 3.0 ± 0.7 mg/L per hour),AUC(0-∞)(3.3 ± 0.6 vs 3.2 ± 0.8 mg/L per hour),Tmax (2.3 ± 0.9 vs 2.1 ± 0.9 h) and T1/2 (2.8 ± 0.3 vs 3.1± 0.4 h). In addition, double-peak absorption profiles of ranitidine were found in some Chinese volunteers.For bismuth, those parameters derived from test and reference drug were as follows: Cmax (11.80 ± 7.36 vs 11.40 ± 6.55 μg/L),AUC(0-t) (46.65 ± 16.97 vs 47.03 ±21.49 μg/L per hour), Tmax (0.50 ± 0.20 vs 0.50 ± 0.20 h)and T1/2 (10.2 ± 2.3 vs 13.0 ± 6.9 h). Ninety percent of confidence intervals for the test/reference ratio of Cmax,AUC(0-t) and AUC(0-∞) derived from both ranitidine and bismuth were found within the bioequivalence acceptable range of 80%-125%. No significant difference was found in Tmax derived from both ranitidine and bismuth.CONCLUSION: The two compound preparations are bioequivalent and may be prescribed

  10. Syntheses, crystal structures and characterizations of two new bismuth(III) arsenites

    Energy Technology Data Exchange (ETDEWEB)

    Liu Junhui [State Key Laboratory of Structural Chemistry, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou 350002 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100039 (China); Kong Fang [State Key Laboratory of Structural Chemistry, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou 350002 (China); Gai Yanli [State Key Laboratory of Structural Chemistry, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou 350002 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100039 (China); Mao Jianggao, E-mail: mjg@fjirsm.ac.cn [State Key Laboratory of Structural Chemistry, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou 350002 (China)

    2013-01-15

    Two new bismuth arsenites with two different structural types, namely, Bi{sub 2}O(AsO{sub 3})Cl (1), Bi{sub 8}O{sub 6}(AsO{sub 3}){sub 2}(AsO{sub 4}){sub 2} (2), have been synthesized by the solid-state reactions. Compound 1 exhibits novel 2D bismuth arsenite layers with Bi{sub 4}O{sub 4} rings capped by oxide anions, which are further interconnected by Bi-Cl-Bi bridges into a 3D network. Compound 2 contains both arsenite and arsenate anions, its 3D structures are based on 1D bismuth arsenite and 1D bismuth arsenate chains both along b-axis, which are interconnected by oxide anions via Bi-O-Bi bridges, forming 1D tunnels of Bi{sub 4}As{sub 4} 8-membered rings (MRs) along b-axis, the lone pairs of the arsenite groups are orientated toward the centers of the above tunnels. Thermogravimetric analysis indicated that both compounds display high thermal stability. Optical property measurements revealed that they are wide band-gap semiconductors. Both compounds display broad green-light emission bands centered at 506 nm under excitation at 380 and 388 nm. - Graphical abstract: Solid state reactions of Bi{sub 2}O{sub 3} (BiCl{sub 3}) and As{sub 2}O{sub 3} yielded two new compounds with two different structural types, namely, Bi{sub 2}O(AsO{sub 3})Cl (1), Bi{sub 8}O{sub 6}(AsO{sub 3}){sub 2}(AsO{sub 4}){sub 2} (2). They represent the first examples of bismuth arsenates. Highlights: Black-Right-Pointing-Pointer Solid state reactions of Bi{sub 2}O{sub 3} (BiCl{sub 3}) and As{sub 2}O{sub 3} yielded two new phases. Black-Right-Pointing-Pointer They represent the first examples of bismuth arsenites. Black-Right-Pointing-Pointer The two compounds exhibit two different structural types.

  11. Synthesis and characterization of Bismuth ferrite (BiFeO{sub 3}) nanoparticles by solution evaporation method

    Energy Technology Data Exchange (ETDEWEB)

    Manzoor, A., E-mail: alinamanzoor@hotmail.com; Afzal, A.M., E-mail: amirafzal461@gmail.com; Umair, M., E-mail: umairranwerr@gmail.com; Ali, Adnan, E-mail: adnnan_1982@yahoo.com; Rizwan, M., E-mail: h.rizwan70@gmail.com; Yaqoob, M.Z., E-mail: zeeshaan32@yahoo.com

    2015-11-01

    Single phase Bismuth ferrite (BiFeO{sub 3}) with high magnetization and polarization was synthesized by solution evaporation method (SEM) at room temperature. The influence of temperature and size of nanoparticles on magnetic properties was studied. The prepared Bismuth ferrite (BiFeO{sub 3}) was characterized by X-ray diffraction (XRD) to investigate the structure and size of crystal. The average crystallite size of nanoparticles (NPs) as calculated by X-ray diffraction (XRD) falls in the range of 22–31 nm. The crystallite size of Bismuth ferrite increased as the temperature varied from 450 °C to 650 °C. Magnetic properties were studied by using physical properties measurement system (PPMS). It was also observed that the magnetic properties were directly related to the size and temperature of Bismuth ferrite nanoparticles. It has been investigated that the magnetization was decreased as the temperature and crystallite size increased. - Highlights: • Bismuth ferrite magnetic material was synthesized by solution evaporation method. • Bismuth ferrite shows ferromagnetic properties at room temperature. • Influence of temperature and crystallite size on magnetic properties was observed. • The magnetization was decreased as the temperature and crystallite size increased. • The magnetic moments were found larger in the smaller crystalline size.

  12. Characterization, Leaching, and Filtration Testing for Bismuth Phosphate Sludge (Group 1) and Bismuth Phosphate Saltcake (Group 2) Actual Waste Sample Composites

    Energy Technology Data Exchange (ETDEWEB)

    Lumetta, Gregg J.; Buck, Edgar C.; Daniel, Richard C.; Draper, Kathryn; Edwards, Matthew K.; Fiskum, Sandra K.; Hallen, Richard T.; Jagoda, Lynette K.; Jenson, Evan D.; Kozelisky, Anne E.; MacFarlan, Paul J.; Peterson, Reid A.; Shimskey, Rick W.; Sinkov, Sergey I.; Snow, Lanee A.

    2009-02-19

    A testing program evaluating actual tank waste was developed in response to Task 4 from the M-12 External Flowsheet Review Team (EFRT) issue response plan.() The test program was subdivided into logical increments. The bulk water-insoluble solid wastes that are anticipated to be delivered to the Waste Treatment and Immobilization Plant (WTP) were identified according to type such that the actual waste testing could be targeted to the relevant categories. Eight broad waste groupings were defined. Samples available from the 222S archive were identified and obtained for testing. The actual waste-testing program included homogenizing the samples by group, characterizing the solids and aqueous phases, and performing parametric leaching tests. Two of the eight defined groups—bismuth phosphate sludge (Group 1) and bismuth phosphate saltcake (Group 2)—are the subjects of this report. The Group 1 waste was anticipated to be high in phosphorus and was implicitly assumed to be present as BiPO4 (however, results presented here indicate that the phosphate in Group 1 is actually present as amorphous iron(III) phosphate). The Group 2 waste was also anticipated to be high in phosphorus, but because of the relatively low bismuth content and higher aluminum content, it was anticipated that the Group 2 waste would contain a mixture of gibbsite, sodium phosphate, and aluminum phosphate. Thus, the focus of the Group 1 testing was on determining the behavior of P removal during caustic leaching, and the focus of the Group 2 testing was on the removal of both P and Al. The waste-type definition, archived sample conditions, homogenization activities, characterization (physical, chemical, radioisotope, and crystal habit), and caustic leaching behavior as functions of time, temperature, and hydroxide concentration are discussed in this report. Testing was conducted according to TP-RPP-WTP-467.

  13. Synthesis of α-Bismuth oxide using solution combustion method and its photocatalytic properties

    Science.gov (United States)

    Astuti, Y.; Fauziyah, A.; Nurhayati, S.; Wulansari, A. D.; Andianingrum, R.; Hakim, A. R.; Bhaduri, G.

    2016-02-01

    The monoclinic bismuth oxide was prepared by the solution combustion method using bismuthyl nitrate as the raw material and citric acid as fuel. The synthesis process consisted of the formation of a clear transparent solution and the formation of white powder after heating the mixture at 250 °C for 2 hours. The yellow pale crystalline materials were obtained after calcination of the white powder at 600 °C for 80 minutes. Furthermore, the photocatalytic activity of the product was also studied using methyl orange as a model pollutant. The result showed that the coral reef-like bismuth oxide was able to degrade 50 mL methyl orange (5 ppm) by 37.8% within 12 hours irradiation using 75-watt tungsten lamp.

  14. A route for polonium 210 production from alpha-particle irradiated bismuth-209 target

    International Nuclear Information System (INIS)

    A method is proposed for production of polonium-210 via the 209Bi(α,3n)210 At nuclear reaction. Bombardment of a bismuth-209 target was performed with a 37 MeV alpha-particle beam that leads to the production of astatine-210 (T1/2 = 8.1 h), which decays to polonium-210. It is purified from the bismuth target matrix by employing liquid-liquid extraction using tributyl phosphate (TBP) in para-xylene from 7 M hydrochloric acid. Back extraction of polonium-210 was performed by 9 M nitric acid. This method allows to purify a tracer amount of Po-210 (2.6 x 10-13 mol) from macroscopic amount of Bi (2.8 x 10-2 mol).

  15. Designing and operating experience on solid electrolyte activity meters for oxygen in lead-bismuth coolant

    International Nuclear Information System (INIS)

    The device for measuring the oxygen activity in the lead and bismuth meets within the range of 1-10-7 with the inertia up to 5 s is developed and tested on the basis of applying the ZrO2-Y2O3 solid-electrolytes in combination with the liquid-metal reference electrodes (Bi, In, Pb). The range of the working temperatures of the activity meter constitutes 280-600 deg C; the stability by thermoshocks up to 50 deg C/s is guaranteed. The device is recommended for application in the circulating systems with the lead and bismuth meets at the coolant pressures up to 60 atm

  16. Compatibility tests on steels in molten lead and lead-bismuth

    International Nuclear Information System (INIS)

    The compatibility of steels with liquid lead and liquid lead-bismuth is a critical issue for the development of accelerator-driven system (ADS). In this work the results of a set of preliminary tests carried out in stagnant molten lead at 737 K and in lead-bismuth at 573, 673 and 749 K are summarised. The tests were conducted for 700, 1200, 1500 and 5000 h. Three steels were tested: two martensitic steels (mod. F82H and MANET II) and one austenitic steel (AISI 316L). The martensitic steels underwent oxidation phenomena at the higher testing temperature, due to oxygen dissolved in the melts. At a lower test temperature (573 K) and higher exposure time (5000 h) the oxidation rate of the martensitic steel seems to be lower and the developed oxide layer protective against liquid metal corrosion. The austenitic steel, in turn, exhibited an acceptable resistance to corrosion-oxidation under the test conditions

  17. Elastic properties of bismuth layer-structure perovskite single crystals studied by brillouin scattering

    International Nuclear Information System (INIS)

    Elastic properties of bismuth layered perovskite compounds, LaxBi4-xTi3O12 (LBT-x) and SrBi2Ta2O9 (SBT), were examined at room temperature by Brillouin scattering. Elastic stiffness coefficients, c33 and c44, defined in the pseudotetragonal symmetry, were obtained. The longitudinal sound velocities propagating along the c axis, were 3985 m/s and 3118 m/s for the pure bismuth titanate (BTO) and SBT, respectively. The sound velocity of SBT is very slow and is believed to be related with the weak interlayer bonding of this layer-structure compound. A simple linear chain model showed that the difference in the sound velocity between BTO and SBT is mainly due to the difference in the c axis lattice constant. The sound velocity of LBT-x increased slightly with the increase of x, while c33 seems to be insensitive to x

  18. Recovery of IR luminescence in photobleached bismuth-doped fibers by thermal annealing

    Science.gov (United States)

    Firstov, S. V.; Firstova, E. G.; Alyshev, S. V.; Khopin, V. F.; Riumkin, K. E.; Melkumov, M. A.; Guryanov, A. N.; Dianov, E. M.

    2016-08-01

    The effect of annealing temperature on the luminescent properties of bismuth-doped fibers bleached by 532 nm laser radiation was investigated. The photoluminescence (PL) measurements were performed in pristine and photobleached samples which were thermally annealed at various temperatures ranging from 100 to 900 °C and slowly cooled. We observed that the intensity of the PL band at 1700 nm in the photobleached fibers recovered its pre-bleached level. Moreover, it was shown that a significant increase of the PL level could be achieved using the special annealing regime. Thereby, we obtained the experimental evidence of a thermally activated recovery process of the PL intensity showing that photoinduced changes of PL in bismuth-doped fibers are completely reversible. The mechanism of the thermal recovery of the PL is discussed.

  19. MYRRHA ADS DATABASE: Part I. Thermophysical properties of molten lead-bismuth eutectic. Version 1

    International Nuclear Information System (INIS)

    This report is an update of the internal SCK-CEN report IR-18 'Database of thermal properties for the melted lead-bismuth eutectic' issued in 2002. This compilation takes into account larger amount of original sources and, partially, the work performed in the framework of the preparation of a 'zero' version of the HLMC Handbook by the OECD/NEA Working Group on LBE Technology. An analysis is performed of the previous recommendations using some general physical laws and referencing to the properties of lead and bismuth. The updated and extended version of the molten LBE thermal properties database is developed and the correlations are proposed for the design calculations of ADS MYRRHA. (author)

  20. Graphite felt modified with bismuth nanoparticles as negative electrode in a vanadium redox flow battery.

    Science.gov (United States)

    Suárez, David J; González, Zoraida; Blanco, Clara; Granda, Marcos; Menéndez, Rosa; Santamaría, Ricardo

    2014-03-01

    A graphite felt decorated with bismuth nanoparticles was studied as negative electrode in a vanadium redox flow battery (VRFB). The results confirm the excellent electrochemical performance of the bismuth modified electrode in terms of the reversibility of the V(3+) /V(2+) redox reactions and its long-term cycling performance. Moreover a mechanism that explains the role that Bi nanoparticles play in the redox reactions in this negative half-cell is proposed. Bi nanoparticles favor the formation of BiHx , an intermediate that reduces V(3+) to V(2+) and, therefore, inhibits the competitive irreversible reaction of hydrogen formation (responsible for the commonly observed loss of Coulombic efficiency of VRFBs). Thus, the total charge consumed during the cathodic sweep in this electrode is used to reduce V(3+) to V(2+) , resulting in a highly reversible and efficient process. PMID:24520000

  1. Intercalation of pyridine and its derivatives into crystalline bismuth molybdenum hydrous oxide

    International Nuclear Information System (INIS)

    Bismuth molybdenum hydrous oxide was prepared by water-thermally direct precipitation in relatively concentrated solutions. The composition of the resulting product was Bi2Mo3O12 x 3.86 H2O determined by thermal analysis and ICP. The X-ray powder diffraction patterns of the crystal synthesized was identical with that of Bi2Mo3O12 x 4.75 H2O. Pyridine, 2,5-dimethylpyridine and 4-benzylpiridine were intercalated into inorganic crystal, significantly expanding interlayer distance along b axis in the monoclinic cell unit of bismuth molybdenum hydrous oxide. The organic molecules were intercalated by solvent exchange mechanism which mainly devoted to the expansion of interlayer spacing. (author)

  2. Synthesis of Bismuth Ferrite Nanoparticles via a Wet Chemical Route at Low Temperature

    Directory of Open Access Journals (Sweden)

    Yongming Hu

    2011-01-01

    Full Text Available Nanoparticles (NPs of multiferroic bismuth ferrite (BiFeO3 with narrow size distributions were synthesized via a wet chemical route using bismuth nitrate and iron nitrate as starting materials and excess tartaric acid and citric acid as chelating agent, respectively, followed by thermal treatment. It was found that BiFeO3 NPs crystallized at ∼350∘C when using citric acid as chelating agent. Such crystallization temperature is much lower than that of conventional chemical process in which other types of chelating agent are used. BiFeO3 NPs with different sizes distributions show obvious ferromagnetic properties, and the magnetization is increased with reducing the particle size.

  3. The photorefractive characteristics of bismuth-oxide doped lithium niobate crystals

    International Nuclear Information System (INIS)

    Bismuth-doped lithium niobate (LN:Bi) crystals were grown by Czochralski method and their optical damage resistance, photorefraction, absorption spectra, and defect energy levels were investigated. The experimental results indicate that the photorefractive properties of LN:Bi were enhanced as compared with congruent one, the photorefractive response time was greatly shortened, the photorefractive sensitivity was increased, and the diffraction efficiency of near-stoichiometric LN:Bi (SLN:Bi) reached 31.72% and 49.08% at 532 nm and 488 nm laser, respectively (light intensity of 400 mW/cm2). An absorption peak at about 350 nm was observed in the absorption spectrum of LN:Bi. And the defect energy levels simulation indicates new defect levels appear in the forbidden gap of LN:Bi crystals. Therefore bismuth can act as photorefractive centers in LN crystals

  4. An evaluation of activated bismuth isotopes in environmental samples from the former Western Pacific Proving Grounds

    International Nuclear Information System (INIS)

    207Bi (T1/2 =32.2 y) was generated by activation of weapons material during a few 'clean' nuclear tests at the U.S. Westren Pacific Provung Grounds of Enewetak and Bikini Atolls. The radionuclides first appeared in the Enewetak environment during 1958 and in the environment of Bikini during 1956. Crater sediments from Bikini with high levels of 207Bi were analyzed by gamma-spectrometry in an attempt to determine the relative concentrations of 208Bi (T1/2 = 3.68 x 105 y). The bismuth isotopes were probably generated during the 'clean', 9.3 Mt Poplar test held on 7/12/58. The atom ratio of 208Bi to 207Bi (R value) ranges from ∼ 12 to over 200 in sections of core sediments from the largest nuclear crater at Bikini atoll. The presence of bismuth in the device is suggested to account for R values in excess of 10. (author)

  5. Spectral investigation of highly ionized bismuth plasmas produced by subnanosecond Nd:YAG laser pulses

    Science.gov (United States)

    Wu, Tao; Higashiguchi, Takeshi; Li, Bowen; Arai, Goki; Hara, Hiroyuki; Kondo, Yoshiki; Miyazaki, Takanori; Dinh, Thanh-Hung; Dunne, Padraig; O'Reilly, Fergal; Sokell, Emma; O'Sullivan, Gerry

    2016-02-01

    The unresolved transition arrays (UTAs) emitted from laser produced bismuth (Bi) plasma sources show potential for single-shot live cell imaging. We have measured extreme ultraviolet spectra from bismuth laser produced plasmas in the 1-7 nm region using a λ = 1064 nm Nd:YAG laser with a pulse duration of 150 ps. Comparison of spectra obtained under different laser power densities with calculations using the Hartree-Fock with configuration interaction Cowan suite of codes and the UTA formalism, as well as consideration of previous predictions of isoelectronic trends, are employed to identify lines and a number of new features in spectra from Bi XXIII to Bi XLVII. The results show that Δn = 0, n = 4-4 emission from highly charged ions merges to form intense UTAs in the 4 nm region and Δn = 1, n = 4-5 resonance transitions UTAs dominate the 1-3 nm region of the Bi spectrum.

  6. 67 cm long bismuth-based erbium doped fiber amplifier with wideband operation

    International Nuclear Information System (INIS)

    In this paper, we demonstrate a wideband Bismuth-based erbium doped fiber amplifier (Bi-EDFA) using two pieces of bismuth-based erbium-doped fiber (Bi-EDF) with a total length of 67 cm as gain media in a double pass parallel configuration. Both Bi-EDFs have an erbium ion concentration of 6300 ppm. Compared to conventional silica-based erbium-doped fiber amplifier (Si-EDFA) with the same amount of erbium ions, the Bi-EDFA provides a higher attainable gain as well as a greater amplification bandwidth, which ranging from 1525 to 1620 nm. The proposed Bi-EDFA achieved a wideband gain of around 18 dB within the wavelength region from 1530 to 1565 nm. The noise figures are maintained below 10 dB within a wide wavelength region from 1535 nm to 1620 nm

  7. Mixed-layered bismuth--oxygen--iodine materials for capture and waste disposal of radioactive iodine

    Energy Technology Data Exchange (ETDEWEB)

    Krumhansl, James L; Nenoff, Tina M

    2015-01-06

    Materials and methods of synthesizing mixed-layered bismuth oxy-iodine materials, which can be synthesized in the presence of aqueous radioactive iodine species found in caustic solutions (e.g. NaOH or KOH). This technology provides a one-step process for both iodine sequestration and storage from nuclear fuel cycles. It results in materials that will be durable for repository conditions much like those found in Waste Isolation Pilot Plant (WIPP) and estimated for Yucca Mountain (YMP). By controlled reactant concentrations, optimized compositions of these mixed-layered bismuth oxy-iodine inorganic materials are produced that have both a high iodine weight percentage and a low solubility in groundwater environments.

  8. Synthesis and Electrochemical Sensing Toward Heavy Metals of Bunch-like Bismuth Nanostructures

    Science.gov (United States)

    Zhang, Zhi; Yu, Ke; Bai, Dan; Zhu, Ziqiang

    2010-02-01

    Large-scale bunch-like bismuth (Bi) nanostructures were the first time to be synthesized via two-step electrochemical deposition. The growth mechanism of the nanostructures was discussed. Such a designed bunch-like Bi electrode has high sensitivity to detect the heavy metal ions due to its unique three-dimensional structures and strong ability of adsorbing the heavy metal ions. The bunch-like Bi electrode’s detection of heavy metals was statically performed using anodic stripping voltammetry (ASV). The detection in the Pb(II) concentration range of 2.5-50 μg/l was also performed. Based on the experimental results, this bunch-like Bi electrode can be considered as an interesting alternative to common mercury electrodes and bismuth film electrodes for possible use in electrochemical studies and electroanalytical applications.

  9. Quantum transport, anomalous dephasing, and spin-orbit coupling in an open ballistic bismuth nanocavity

    Science.gov (United States)

    Hackens, B.; Minet, J. P.; Faniel, S.; Farhi, G.; Gustin, C.; Issi, J. P.; Heremans, J. P.; Bayot, V.

    2003-03-01

    The phase coherence time τφ and spin-orbit coupling time τso are measured in a bismuth quasiballistic nanocavity and in bismuth thin films using weak antilocalization and universal conductance fluctuations. The cavity is found to be zero dimensional for phase-coherent processes at low temperature. Weak antilocalization seems weakly affected by this drastic reduction of dimensionality. The temperature dependence of τφ is similar in both types of samples, qualitatively consistent with low-energy transfer two-dimensional electron-electron interaction effects as the dominant dephasing mechanism. Strikingly, τφ in the dot is found to be an order-of-magnitude smaller than in the film, and orders-of-magnitude smaller than the theoretical prediction.

  10. Equilibrium evaporation of trace polonium from liquid lead–bismuth eutectic at high temperature

    International Nuclear Information System (INIS)

    Highlights: •We studied evaporation of trace polonium from liquid lead–bismuth eutectic. •Our methods for Po are validated through analysis of LBE evaporation. •At low concentration Po evaporates from LBE according to Henry’s law. •New Henry constant-temperature correlations for Po in LBE are presented. -- Abstract: The evaporation of Po from its dilute solution in liquid lead–bismuth eutectic (LBE) was determined between 700 and 1000 °C in Ar/5%H2 by the transpiration method. Concurrent measurements of the evaporation of LBE could be well reproduced by calculations using literature data, confirming conditions of equilibrium and convective vapor transport in our transpiration method experiments. This allowed to model the Po evaporation data and extract accurate temperature correlations for the Henry constant for Po dissolved in LBE at two different Po concentrations. Extrapolations of the new correlations were in excellent agreement with existing data at lower temperature

  11. Ab initio lattice dynamics and thermochemistry of layered bismuth telluride (Bi2Te3)

    Science.gov (United States)

    Zurhelle, Alexander F.; Deringer, Volker L.; Stoffel, Ralf P.; Dronskowski, Richard

    2016-03-01

    We present density-functional theory calculations of the lattice dynamics of bismuth telluride, yielding force constants, mean-square displacements and partial densities of phonon states which corroborate and complement previous nuclear inelastic scattering experiments. From these data, we derive an element- and energy-resolved view of the vibrational anharmonicity, quantified by the macroscopic Grüneisen parameter γ which results in 1.56. Finally, we calculate thermochemical properties in the quasiharmonic approximation, especially the heat capacity at constant pressure and the enthalpy of formation for bismuth telluride; the latter arrives at ▵H f (Bi2Te3)  =  -102 kJ mol-1 at 298 K.

  12. Evaluation of bismuth shielding effectiveness in reducing breast absorbed dose during thoracic CT scan

    Energy Technology Data Exchange (ETDEWEB)

    Alonso, T. C.; Mourao, A. P.; Santana, P. C.; Silva, T. A. [Federal University of Minas Gerais, Program of Nuclear Science and Techniques, Av. Pte. Antonio Carlos 6627, 31270-901 Belo Horizonte, Minas Gerais (Brazil)

    2015-10-15

    Computed Tomography (CT) is an essential method for tracking neoplasia and efficiently diagnosing a wide variety of thoracic diseases. CT is generally considered the most accurate choice for lung examination. Due to the growing use of CT, breast and other superficial and radiosensitive organs are unnecessarily irradiated during radiological procedures, thus requiring the development of strategies appropriate to optimize and, if possible, to reduce the radiation dose. The use of bismuth shielding to reduce radiation dose absorbed by breast during thoracic CT examinations has been the subject of many studies recently published by Brazilian and foreign authors of various fields. The purpose of this paper is both to accurately determine the glandular dose when breast is exposed to radiation and to assess the reduction in absorbed dose during thoracic CT examinations, using a set of Thermoluminescent Dosimeters, an anthropomorphic phantom and bismuth shielding. (Author)

  13. Gamma-ray shielding and structural properties of barium-bismuth-borosilicate glasses

    Science.gov (United States)

    Bootjomchai, Cherdsak; Laopaiboon, Jintana; Yenchai, Chadet; Laopaiboon, Raewat

    2012-07-01

    The attenuation coefficients of barium-bismuth-borosilicate glasses have been measured for gamma-ray photon energies of 662, 1173 and 1332 keV using a narrow beam transmission geometry. These coefficients were then used to obtain the values of mass attenuation coefficients, effective atomic number, effective electron density and mean free path. Good agreement has been observed between experimental and theoretical values of these parameters. From the obtained results it is reported here that from the barium-bismuth-borosilicate glasses are better shields to gamma-radiations in comparison to the standard radiation shielding concretes from the shielding point of view. The molar volume, FTIR and acoustic investigations have been used to study the structural properties of the prepared glass system. The obtained results reveal that the formation of non-bridging oxygens occurs at higher concentration of Bi2O3.

  14. Evaluation of bismuth shielding effectiveness in reducing breast absorbed dose during thoracic CT scan

    International Nuclear Information System (INIS)

    Computed Tomography (CT) is an essential method for tracking neoplasia and efficiently diagnosing a wide variety of thoracic diseases. CT is generally considered the most accurate choice for lung examination. Due to the growing use of CT, breast and other superficial and radiosensitive organs are unnecessarily irradiated during radiological procedures, thus requiring the development of strategies appropriate to optimize and, if possible, to reduce the radiation dose. The use of bismuth shielding to reduce radiation dose absorbed by breast during thoracic CT examinations has been the subject of many studies recently published by Brazilian and foreign authors of various fields. The purpose of this paper is both to accurately determine the glandular dose when breast is exposed to radiation and to assess the reduction in absorbed dose during thoracic CT examinations, using a set of Thermoluminescent Dosimeters, an anthropomorphic phantom and bismuth shielding. (Author)

  15. Mesozoic Rifting in the German North Sea

    Science.gov (United States)

    Lutz, R.; Jähne, F.; Arfai, J.

    2013-12-01

    The Central Graben is the southernmost expressions of the Mesozoic North Sea rift system that includes the Viking Graben, Moray Firth-Witch Ground grabens and the Horda-Egersund half graben. In the southern North Sea the Central Graben extends across the Dutch and the German exclusive economic zones. The structure of the Central Graben in German territorial waters was mapped in great detail in 2D and 3D seismic data and the stratigraphy has been constraint by borehole data. We provide a detailed review of the rifting activity in the German North Sea sector both in time and space and the link between rifting and salt movement. Major rifting activity started in the Central Graben during the Late Triassic and peaked during the Late Jurassic when extensive rift grabens formed, further influenced by halokinetic movements. First subsidence in the Central Graben area appears in the Early Triassic. This is documented by thickness variations in the sedimentary strata from the Triassic to the Jurassic. Remarkably thick sediments were deposited during the Late Triassic along the eastern border fault of the Central Graben and in the Late Jurassic sediments accumulated along graben-wide extensional faults and in rim-synclines of salt-structures. A basin inversion commenced in the Late Cretaceous resulting in an erosion of wide portions of Lower Cretaceous rocks or even complete removal in some parts. The area to the east of the Central Graben faced a completely different evolution. In this area major rifting activity initiated already in the Early to Middle Triassic. This is evident from huge packages of Middle Buntsandstein to Muschelkalk (Middle Triassic) sediments in the Horn Graben. Jurassic doming, forming the Mid-North Sea High, resulted in almost complete erosion of Lower and Middle Jurassic sediments in the central German North Sea. Sedimentation continued during the Early and Late Cretaceous. The Glückstadt Graben, which is a structure located farther east has a

  16. Short Takes: Intelligence-Service Psychology: A German Perspective

    Directory of Open Access Journals (Sweden)

    Dr. Helmut Müller-Enbergs

    2008-01-01

    Full Text Available To date, four German volumes in the series "Intelligence-Service Psychology" (Nachrichtendienstpsychologie have been published. These volumes generated interest in both the German and non-German speaking communities. It was therefore decided to translate some of the basic articles of the series into English (Litzcke, Müller-Enbergs & Ungerer, 2008, making them accessible to a wider range of readers. This article contains abbreviated versions of the articles in the book.

  17. On German-Croatian and Italian-Croatian Language Contact

    OpenAIRE

    Glovacki-Bernardi, Zrinjka; Jernej, Mirna

    2004-01-01

    Croatia has always been a multilingual environment. The influence of German and Italian was empowered through direct political influence. During the second part of the 18th and in the 19th century native speakers of German and Italian used Croatian as a second language carrying out their duties at work. This bilingualism can tentatively be referred to as bureaucratic bilingualism. Native Croatian speakers used Italian and German as a second language in certain social areas. Suc...

  18. The role of accounting in the German financial system

    OpenAIRE

    Leuz, Christian; Wüstemann, Jens

    2003-01-01

    This chapter analyzes the role of financial accounting in the German financial system. It starts from the common perception that German accounting is rather "uninformative". This characterization is appropriate from the perspective of an arm’s length or outside investor and when confined to the financial statements per se. But it is no longer accurate when a broader perspective is adopted. The German accounting system exhibits several arrangements that privately communicate information to ins...

  19. The representation of work in German grammar books

    OpenAIRE

    Leahy, Angela

    2004-01-01

    This dissertation explores the language of three German grammar books and accompanying exercise books which are produced in Germany for international students of German. It examines how the examples and exercises presented in these books constitute ‘colony texts’ which convey different representations of human activity to the reader. Analysis of the language used in the German grammar books centres on the Linguistics of Representation and borrows techniques used normally in Corpus Linguistics...

  20. German and English comparison of fluency development and stuttering.

    OpenAIRE

    Dworzynski, K.

    2004-01-01

    The thesis explored disfluencies in stuttering through linguistic contrasts between English and German. Part one focused on the analysis of speech samples of German speaking adults and children who stutter. Part two analysed bilingual German-English language development aiming to examine whether increased cognitive load of two languages is related to language errors. Since people who stutter do not speak disfluently all the time, but have stretches where speech is fluent, research has investi...

  1. The Burden of History? Civic Education at German Schools

    OpenAIRE

    Christa Händle

    2002-01-01

    The following essay gives an overview of the development of civic education at German schools in the 20th century. This is based on the study of German contributions to the international comparative project "Civic Education" within the scheme of the International Association for Evaluation of Educational achievement (IEA), which were published internationally and by the German project group. Essential empirical findings are taken into account to describe civic education in Germany in an inter...

  2. Border effects and border regions: Lessons from the German unification

    OpenAIRE

    Nitsch, Volker

    2002-01-01

    This paper examines data on trade flows between West German Bundesländer (federal states) and East Germany to explore the effect of national borders on trade. Although the data cover only a small fraction of intra-German trade flows, I find a home bias of about factor 2.2; West German shipments to East Germany are about 120% larger than deliveries to an otherwise similar foreign country. Based on this result, possible implications for border regions are discussed

  3. STERN – A Rocket programme for German Students

    OpenAIRE

    Stamminger, Andreas; Ciezki, Helmut; Kitsche, Wolfgang; Kobald, M.; Lappöhn, Karsten; Schmidt, Alexander

    2013-01-01

    In April 2012 the German Aerospace Center DLR, launched a support programme for students to develop, build and launch their own rockets. The programme goes by the acronym STERN (STudentische Experimental-RaketeN) which is also the German word for star. Supported by funds from the Federal Ministry of Economics and Technology (BMWi) and conducted by the DLR Space Administration of the German Aerospace Center DLR, the STERN programme provides aerospace engineering faculties at universities with ...

  4. Industrial Policy and the East German Productivity Puzzle

    OpenAIRE

    Klodt, Henning

    1999-01-01

    Catching-up of East German productivity to West German levels has completely faded out since the mid l990s. The remaining productivity gap cannot be attributed to an inferior capital endowment. Instead, it appears to be the result of an inappropriate design of industrial policy which fostered the specialization of East German industry on capital intensive smoke-stack industries. These industries are absorbing a large share of factor inputs, whereas their contribution to aggregate output is ra...

  5. Entrepreneurial ventures and wage differentials between Germans and immigrants

    OpenAIRE

    Constant, Amelie; Shachmurove, Yochanan

    2003-01-01

    This paper focuses on the entrepreneurial undertaking of immigrants and natives in Germany. We first study factors that affect the sorting of individuals into self-employment and then we investigate whether self-employment has a differential effect on the wages of individual workers and can lead them to economic success. We employ recent data from the German Socioeconomic Panel that allow us to identify and compare four distinct groups: West Germans, East Germans, guestworkers, and ethnic Ger...

  6. HRM in the German business system: A review

    OpenAIRE

    Giardini, Angelo; Kabst, Rüdiger; Müller-Carmen, Michael

    2005-01-01

    Human resource management in Germany is deeply rooted in its institutional environment. Thus, US style HRM cannot be simply transferred to the German context. Nevertheless, the German business system is not hostile to HRM principles. Rather, these practices have to be adapted to the demands and constrains of the German socio-economic context. The key labour market institutions of collective bargaining, co-determination, and initial vocational training in particular require a pluralist style o...

  7. What is Economics? Attitudes and views of German economists

    OpenAIRE

    Frey, Bruno S.; Humbert, Silke; Schneider, Friedrich

    2009-01-01

    Which schools of thought are favored by German economists? What makes a good economist and which economists have been most influential? These questions were addressed in a survey, conducted in the summer of 2006 among the members of the ‘Verein für Socialpolitik’, the association of German speaking economists. An econometric analysis is used to identify to what extent ideological preferences or personal factors determine the respondents’ answers. Our results suggest that German economists fav...

  8. Determinants of German Foreign Direct Investment: A Case of Failure?

    OpenAIRE

    Dr. Ioannis-Dionysios Salavrakos

    2009-01-01

    The aim of this paper is to explain Foreign Direct Investment of German enterprises. The theory of Foreign Direct Investment identifies a variety of location-specific, strategic, financial, as well as other motives which firms have in order to become multinationals. We apply the above theoretical schemata to the case of German enterprises and we also consider the evolution of German FDI in a historical context. The main conclusion of the research findings is that financial, strategic and loca...

  9. Sibling Rivalry in Educational Attainment: The German Case

    OpenAIRE

    Bauer, Thomas K.; Ira N. Gang

    2000-01-01

    Recent studies exploring sibling rivalry in the allocation of household resources in the U.S. produce conflicting results. We contribute to this discussion by addressing the role of sibling rivalry in educational attainment in Germany. Using the German Socioeconomic Panel (GSOEP) we are able to distinguish how the effects of sibling rivalry vary by cultural affiliation, i.e., among families of West German, East German and foreign origin. We also point out and correct for a reference group pro...

  10. Reflections and reciprocity : China and German modernist literature

    OpenAIRE

    Tsui, Chiann Karen

    2013-01-01

    This dissertation examines the portrayal of China in German modernist literature, as well as the adaptation of said literature in post-Mao China. It analyzes how the German texts of the modernist period negotiate cultural and political identity in the age of imperialism and Orientalism, and how their Chinese interpretations approach similar issues of representation and reform in different decades of China after Mao. How do the de-nationalizing elements of the original German-language writings...

  11. Input Modifications by Instructors in Traditional and Business German Courses

    OpenAIRE

    Schierloh, Maren; Paulsell, Patricia R.

    2010-01-01

    Inspired by the debate on the effi cacy of modifi ed input (i.e., teacher talk), this study explored the use of input modifi cations in a traditional German course compared to a business German course. Overall, the business language instructor resorted to less simplifi cation than the instructor of the traditional German course. In terms of general modifications, the business language instructor used frequent repetitions of context-specifi c vocabulary and expressions, while focusing on stude...

  12. German Market Analysis: Tourist Behavior Research: case Rock and Lake

    OpenAIRE

    Koppalova, Nadezhda

    2014-01-01

    The research problem of this thesis was to identify a potential tourist market segment in Germany for the Finnish company Rock and Lake which provides accommodation and activities. The main objectives of this work were to identify the current trends of a German travel market in selecting vacation destinations, study the attitude of German tourists towards different types of vacations and holiday parameters, analyze German tourist market segmentation and analyze “Rock and Lake’...

  13. Colombian-German entrepreneurial and scientific cooperation

    Energy Technology Data Exchange (ETDEWEB)

    Oettel, Eberhard [Foerdergesellschaft Erneuerbare Energien e.V. (FEE), Berlin (Germany)

    2009-07-01

    German and Colombian strategic objectives, strengths and needs suit for a long-lasting cooperation ot mutual advantage in the fields of renewable energy resources (RES), energy efficiency biodiversity, biofuels: Colombia as a country rich of fossil primary energy carriers strives to substitute them by its abundant RES for the supply of electricity, heat (cold) and fuels, set them free for exporting to gain financial revenues for a self-determined technological development. Despite of its for a developing country relatively high technological level an indigenous industry of renewable energy hardly does not exist. Favourable interfaces in many regard prevail too in the energy related science, among others in biotechnology and the brand-new branch of urban agriculture. German middle-class enterprises and scientific institutes dispose of exactly suitable necessary technologies, engineering kow-how of their application and are increasingly obliged to look for foreign markets just in this segment. Joint research, development and implementation, including adapting high technologies to Colombian conditions is welcome to develop advanced knowledge and new applications. By growing cooperation of Latin American countries the chances for joint venturing with Colombian partners in the this market increase. FEE Foerdergesellschaft Erneuerbare Energien e.V. (Society for the Promotion of Renewable Energy) as a national network for innovations of enterprises, research institutes and experts has established a strong plexus to market relevant partners in Colombia since 2005, ready for manifold use by German partners in the branches of RES, energy efficiency and biofuels. FEE had been integrated into two Centres of Excellence recognized by the Colombian Research Council COLCIENCIAS. Powerful enterprises and associations signed official Letters of Interest. In first joint projects confidence was created, expertise proved and a reliable basement founded for entrepreneural business

  14. Structural, optical and glass transition studies on Nd3+-doped lead bismuth borate glasses

    International Nuclear Information System (INIS)

    Nd3+-doped lead bismuth borate (PbO-Bi2O3-B2O3) glasses were prepared with different concentrations of Nd3+. The structural studies were done through FTIR spectral analysis. The glass transition studies were done through differential scanning calorimetry. The optical analysis was done by using Judd-Ofelt theory. The structural study reveals that the glass has [BiO3], BO4, BO3 and PbO4 units as the local structures

  15. Large-scale synthesis of bismuth sulfide nanorods by microwave irradiation

    International Nuclear Information System (INIS)

    Graphical abstract: Display Omitted Research highlights: → Large-scale Bi2S3 nanorods have been prepared by microwave irradiation methods. → CTAB and β-CD are beneficial to the formation of Bi2S3 nanorods. → DMF, EG and DEG were favorable solvents. → Bismuth and sulfur precursors influenced the size and morphology. → A proposed formation mechanism of Bi2S3 nanorods was summarized. - Abstract: Bismuth sulfide (Bi2S3) has attracted considerable interest due to its potential applications in thermoelectric and electronic devices, optoelectronic devices, and biomedicine. In this study, large-scale highly crystalline Bi2S3 nanorods were successfully prepared from bismuth citrate and thiourea (Tu) by microwave irradiation methods. The products were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM, HRTEM) and selected area electron diffraction (SAED). The influences of reaction time, surfactants, solvents, and precursors on the formation of Bi2S3 nanorods were discussed. The microwave irradiation method reduced reaction time by at least 80% in the synthesis of Bi2S3 nanorods compared with the refluxing method. Cetyltrimethylammonium bromide (CTAB) and β-cyclodextrin (β-CD) were found to be beneficial to the formation of Bi2S3 nanorods. N,N-dimethylformamide, ethylene glycol, and diethylene glycol were the favorable solvents in the fabrication of these nanorods. It was found that different bismuth and sulfur precursors influenced the sizes and morphologies of the Bi2S3 nanorods. The proposed growth mechanism of Bi2S3 nanorods was also discussed.

  16. Eye-lens bismuth shielding in paediatric head CT: artefact evaluation and reduction

    International Nuclear Information System (INIS)

    CT scans of the brain, sinuses and petrous bones performed as the initial imaging test for a variety of indications have the potential to expose the eye-lens, considered among the most radiosensitive human tissues, to a radiation dose. There are several studies in adults discussing the reduction of orbital dose resulting from the use of commercially available bismuth-impregnated latex shields during CT examinations of the head. To evaluate bismuth shielding-induced artefacts and to provide suggestions for optimal eye-lens shielding in paediatric head CT. A bismuth shield was placed over the eyelids of 60 consecutive children undergoing head CT. Images were assessed for the presence and severity of artefacts with regard to eye-shield distance and shield wrinkling. An anthropomorphic paediatric phantom and thermoluminescence dosimeters (TLDs) were used to study the effect of eye lens-to-shield distance on shielding efficiency. Shields were tolerated by 56/60 children. Artefacts were absent in 45% of scans. Artefacts on orbits, not affecting and affecting orbit evaluation were noted in 39% and 14% of scans, respectively. Diagnostically insignificant artefacts on intracranial structures were noted in 1 case (2%) with shield misplacement. Mean eye-lens-to-shield distance was 8.8 mm in scans without artefacts, and 4.3 mm and 2.2 mm in scans with unimportant and diagnostically important artefacts, respectively. Artefacts occurred in 8 out of 9 cases with shield wrinkling. Dose reduction remained unchanged for different shield-to-eye distances. Bismuth shielding-related artefacts occurring in paediatric head CT are frequent, superficial and diagnostically insignificant when brain pathology is assessed. Shields should be placed 1 cm above the eyes when orbital pathology is addressed. Shield wrinkling should be avoided. (orig.)

  17. Study of some health physics parameters of bismuth-ground granulated blast furnace slag shielding concretes

    Science.gov (United States)

    Kumar, Sandeep; Singh, Sukhpal

    2016-05-01

    The Bismuth-ground granulated blastfurnace slang (Bi-GGBFS) concrete samples were prepared. The weight percentage of different elements present inBi-GGBFS Shielding concretewas evaluated by Energy Dispersive X-ray Microanalysis (EDX). The exposure rate and absorbed dose rate characteristics were calculated theoretically for radioactive sources namely 241Am and 137Cs. Our calculations reveal that the Bi-GGBFS concretes are effective in shielding material for gamma radiations.

  18. Report - Melter Testing of New High Bismuth HLW Formulations VSL-13R2770-1

    Energy Technology Data Exchange (ETDEWEB)

    Kruger, Albert A.; Pegg, I. L.; Kot, W. K.; Gan, H.; Matlack, K. S.

    2013-11-13

    The primary objective of the work described was to test two glasses formulated for a high bismuth waste stream on the DM100 melter system. Testing was designed to determine processing characteristics and production rates, assess the tendency for foaming, and confirm glass properties. The glass compositions tested were previously developed to maintain high waste loadings and processing rates while suppressing the foaming observed in previous tests

  19. Compositional dependence of optical band gap and refractive index in lead and bismuth borate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Mallur, Saisudha B.; Czarnecki, Tyler; Adhikari, Ashish; Babu, Panakkattu K.

    2015-08-15

    Highlights: • Refractive indices increase with increasing PbO/Bi{sub 2}O{sub 3} content. • Optical band gap arises due to direct forbidden transition. • Optical band gaps decrease with increasing PbO/Bi{sub 2}O{sub 3} content. • New empirical relation between the optical band gap and the refractive index. - Abstract: We prepared a series of lead and bismuth borate glasses by varying PbO/Bi{sub 2}O{sub 3} content and studied refractive index and optical band gap as a function of glass composition. Refractive indices were measured very accurately using a Brewster’s angle set up while the optical band gaps were determined by analyzing the optical absorption edge using the Mott–Davis model. Using the Lorentz–Lorentz method and the effective medium theory, we calculated the refractive indices and then compared them with the measured values. Bismuth borate glasses show better agreement between the calculated values of the refractive index and experimental values. We used a differential method based on Mott–Davis model to obtain the type of transition and optical band gap (E{sub opt}) which in turn was compared with the value of E{sub opt} obtained using the extinction coefficient. Our analysis shows that in both lead and bismuth borate glasses, the optical band gap arises due to direct forbidden transition. With increasing PbO/Bi{sub 2}O{sub 3} content, the absorption edge shifts toward longer wavelengths and the optical band gap decreases. This behavior can be explained in terms of changes to the Pb−O/Bi−O chemical bonds with glass composition. We obtained a new empirical relation between the optical band gap and the refractive index which can be used to accurately determine the electronic oxide polarizability in lead and bismuth oxide glasses.

  20. Compositional dependence of optical band gap and refractive index in lead and bismuth borate glasses

    International Nuclear Information System (INIS)

    Highlights: • Refractive indices increase with increasing PbO/Bi2O3 content. • Optical band gap arises due to direct forbidden transition. • Optical band gaps decrease with increasing PbO/Bi2O3 content. • New empirical relation between the optical band gap and the refractive index. - Abstract: We prepared a series of lead and bismuth borate glasses by varying PbO/Bi2O3 content and studied refractive index and optical band gap as a function of glass composition. Refractive indices were measured very accurately using a Brewster’s angle set up while the optical band gaps were determined by analyzing the optical absorption edge using the Mott–Davis model. Using the Lorentz–Lorentz method and the effective medium theory, we calculated the refractive indices and then compared them with the measured values. Bismuth borate glasses show better agreement between the calculated values of the refractive index and experimental values. We used a differential method based on Mott–Davis model to obtain the type of transition and optical band gap (Eopt) which in turn was compared with the value of Eopt obtained using the extinction coefficient. Our analysis shows that in both lead and bismuth borate glasses, the optical band gap arises due to direct forbidden transition. With increasing PbO/Bi2O3 content, the absorption edge shifts toward longer wavelengths and the optical band gap decreases. This behavior can be explained in terms of changes to the Pb−O/Bi−O chemical bonds with glass composition. We obtained a new empirical relation between the optical band gap and the refractive index which can be used to accurately determine the electronic oxide polarizability in lead and bismuth oxide glasses