WorldWideScience

Sample records for bismuth 210 target

  1. Special hydrogen target (Prop. 210)

    International Nuclear Information System (INIS)

    Halliday, C.E.

    1979-11-01

    This guide contains a description of the electrical control and automatic vacuum systems for the Special Hydrogen Target (Prop. 210) together with the flow diagram and the mimic control panel layout for the system. (U.K.)

  2. Enhanced counting efficiency of Cerenkov radiation from bismuth-210

    International Nuclear Information System (INIS)

    Peck, G.A.; Smith, J.D.

    1998-01-01

    This paper describes the measurement of 210 Bi by Cerenkov counting in a commercial liquid scintillation counter. The counting efficiency in water is 0.17 counts per second per Becquerel (17%). When the enhancers Triton X-100 (15% v/v) and sodium salicylate (1% m/v) are added to the solution the counting efficiency for 210 Bi increases from 17% to 75%. The 210 Po daughter of 210 Bi causes interference of 0.85 counts per second per Becquerel in the presence of the enhancers but not in water. When 210 Bi and 210 Po are present in secular equilibrium the total counting efficiency is 160%. When 210 Bi and 210 Po are not in secular equilibrium the 210 Po can be removed immediately before counting by plating onto silver foil. The use of the enhancers gives a substantial increase in counting efficiency compared to counting in water. Compared with solutions used in liquid scintillation counting the enhancer solution is inexpensive and can be disposed of without environmental hazard. (author)

  3. Size distribution and origin of lead-210, bismuth-210, and polonium-210 on airborne particles in the troposphere

    International Nuclear Information System (INIS)

    Moore, H.E.; Poet, S.E.; Martell, E.A.

    1980-01-01

    Data are presented on the concentration, specific activity and percent of 210 Pb, 210 Bi, and 210 Po vs particle size interval for ground level air samples. Similar data for 90 Sr in air and 226 Ra and 210 Pb in one soil sample are given. Calculated mean aerosol residence times increase with increasing particle size interval; however, specific activities and percent of each isotope decrease with increasing particle size interval. These variations, along with comparision to soil data, suggest that the distribution of these isotopes reflects the initial attachment distribution plus a smaller component due to entrainment of particles from soil and other surfaces

  4. 210Pb targets for nuclear spectroscopy

    International Nuclear Information System (INIS)

    Maier, H.J.; Grossmann, R.

    1987-01-01

    The preparation of metallic 210 Pb targets by vacuum evaporation condensation is described. Lead-210, which is highly radioactive, is available as nitrate in 3M HNO 3 . Solid Pb(NO 3 ) 2 is extracted from this solution and subjected to a reductive evaporation procedure. A special-shaped evaporation crucible yields a collection efficiency of 2.8 mg/cm 2 per milligram of employed material. (orig.)

  5. Lead-210, bismuth-210, polonium-210. Natural activity, internal dosimetry, and dose factors for ingestion and inhalation

    International Nuclear Information System (INIS)

    Jacobi, W.

    1979-02-01

    Starting with a comprehensive review of the normal, natural activity of 210 Pb and 210 Po in the environment and in the tissues of the human body, a model of the activity and dose distributions of this nuclides in the human body is developed. Dose factors for ingestion with food and for inhalation are derived from this model, related to the intake rate unit. This 'natural exposure model' can be used for an estimation of the population exposure due to normal natural radiation as well as to man-made sourcess of these nuclides, e.g. coal-fired power plants. (orig.) [de

  6. Isotopically tailored lead target with reduced polonium and bismuth radio-waste

    International Nuclear Information System (INIS)

    Khorasanov, G.L.; Ivanov, A.P.; Lunev, V.P.; Blokhin, A.I.

    2002-01-01

    Residual activity of a lead target after 1 year irradiation with a high power, 0.8 GeV*30 mA, proton beam is studied. It is concluded that the main radiotoxicity of irradiated lead is connected with bismuth isotope, Bi-207, which is produced in natural lead, mix of several stable isotopes, via (p,2n) reaction with Pb-208 nuclei. It is proposed to use, as a target material, lead enriched with another stable isotope, Pb-206, in order to reduce producing Bi-207 and Po-210. Estimation of charges for obtaining large quantities of lead-206 is also given. Accumulation of hazardous radionuclides, Bi-207, Bi-208, and Po-210, in natural lead to be used as a coolant in future fast reactors and accelerator driven reactors is predicted. In accelerator driven systems a large portion of Bi-207 can be produced via Pb-208(p,2n)Bi-207 reaction in a target of natural lead (Pb-208/Pb-207/Pb-206/Pb-204=52.35/22.08/24.14/1.42 %). A new isotopically tailored coolant-converter for ADS consisting of lead isotope, Pb-206, is proposed. By using this material, it is possible to reduce essentially the production of the most radio-toxic isotopes of Bi and Po and to avoid disposing the large amounts of lead. To provide the future fast reactors and accelerator driven systems with low-activation coolant - converter, the new technology of obtaining the large amounts of natural lead enriched with lead isotope, Pb-206, should be developed. (authors)

  7. Status and future application of pilot lead-bismuth target circuit TC-1 for ADS

    Energy Technology Data Exchange (ETDEWEB)

    Ignatiev, S.; Leonchuk, M.; Orlov, Y.; Pankratov, D.; Reshetnikova, O.; Suvorov, G.; Zabudko, A. [Institute for Physics and Power Engineering, Obninsk (Russian Federation); Stepanov, V.; Klimov, N. [Experimental and Design Organization, Gidropress, Podolsk (Russian Federation); Hechanova, A.; Ma, J. [Nevada Univ., Las Vegas, NV (United States); Li, N. [Los Alamos National Lab., NM (United States); Gudowski, W. [International Science and Technology Center, Moscow (Russian Federation)

    2007-07-01

    A complicated evolution, status and future application of the pilot molten lead-bismuth target circuit of 1 MW proton beam power (TC-1) as an important part of a target-blanket accelerator driven system (ADS), that has been developed, created and twice tested under the auspice of the International Science and Technology Center (ISTC), is analyzed. The target complex TC-1 is a circulation lead-bismuth loop whose beam window is made of ferritic steel EP-823 (this steel was used in the past as material of fuel rods cladding in reactors cooled with lead-bismuth). At present TC-1 is operating at coolant temperature up to 300 C degrees and will be used to study different issues linked to the use of lead-bismuth: -) interaction with air, water and hydrogen, -) different regimes of flow, -) corrosion, -) filtering, or -) slag formation.

  8. Thermal hydraulic studies of lead–bismuth eutectic spallation target of CIADS

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Kang [Institute of Modern Physics, Chinese Academy of Sciences, 509 Nanchang Rd., Lanzhou, Gansu 730000 (China); University of Chinese Academy of Sciences, 19 A Yuquan Rd, Shijingshan District, Beijing 100049 (China); Yang, Yongwei, E-mail: yangyongwei@impcas.ac.cn [Institute of Modern Physics, Chinese Academy of Sciences, 509 Nanchang Rd., Lanzhou, Gansu 730000 (China); Fan, Deliang; Gao, Yucui [Institute of Modern Physics, Chinese Academy of Sciences, 509 Nanchang Rd., Lanzhou, Gansu 730000 (China)

    2016-08-15

    Highlights: • A 3-D fluid-solid coupling thermal-hydraulic analysis is made for the LBE target. • The reactor and the spallation target is coupled in thermal process. • The heat transfer between the inlet and outlet of the spallation target is taken into account. - Abstract: For the China Initiative Accelerator Driven System (CIADS), it includes three sub-systems: accelerator, spallation target, and sub-critical reactor. The sub-system of spallation target is an important component of the CIADS, which is coupled with the other two sub-systems. The proton beam from the accelerator with an energy of 250 MeV and a current intensity of 2 mA reacts with the nuclei of the lead–bismuth eutectic (LBE), approximately 0.5 MW of heat is deposited in the target zone, which must be removed by circulating the LBE. To reach the goal, we carried out the study by using the Computational Fluid Dynamics (CFD) software FLUENT, to study the flow patterns and temperature distribution in the target zone. For these simulations, the heat transferred from the sub-critical reactor was taken into account. The results indicated that the heat deposited in the target zone can be removed safely.

  9. Elemental Technologies for Lead-Bismuth Spallation Target System in J-PARC

    International Nuclear Information System (INIS)

    Obayashi, H.; Yamaguchi, K.; Saito, S.; Sugawara, T.; Takei, H.; Sasa, T.

    2015-01-01

    Japan Atomic Energy Agency (JAEA) has been researching and developing an Accelerator-Driven System (ADS) as a dedicated system for the transmutation of long-lived radioactive nuclides. The ADS proposed by JAEA uses the lead-bismuth eutectic (LBE) alloy as a spallation target material and a coolant. In the various R and D for ADS, construction of the Transmutation Experimental Facility (TEF) is planned under the framework of the J-PARC project as a preceding step before the construction of demonstrative ADS. In this R and D, TEF is considered for the experimental investigation of the feasibility of the beam window, the structural materials, and to investigate the operation properties of the target system by using 400 MeV-250 kW proton beam. This target system is consisted of various elements and must be able to operate without troubles during an operation period of TEF facility. Furthermore, in the maintenance period after the operation, because the inside of a hot cell storing a target is exposed to strong radiations, all elements must be designed as remote control devices. In this study, the present conditions of the design and the result of performance test of each important elements were confirmed in the realisation of the LBE target system, such as the monitoring system of flow rate by using the ultrasonic method, the heater system with the metallic heat insulator joined to a flow channel of LBE, and the operability of remote handing. (authors)

  10. Lead-Bismuth Eutectic cooled experimental Accelerator Driven System. Windowless target unit thermal-hydraulic analysis

    International Nuclear Information System (INIS)

    Bianchi, F.; Ferri, R.; Moreau, V.

    2004-01-01

    A main concern related to the peaceful use of nuclear energy is the safe management of nuclear wastes, with particular attention to long-lived fission products. An increasing attention has recently been addressed to transmutation systems (Accelerator Driven System: ADS) able to 'burn' the actinides and some of the long-lived fission products (High-Level Waste: HLW), transforming them in short or medium-lived wastes that may be easier managed and stored in the geological disposal, with the consequent easier acceptability by population. An ADS consists of a subcritical-core coupled with an accelerator by means of a target. This paper deals with the thermal-hydraulic analysis, performed with STAR-CD and RELAP5 codes for the windowless target unit of Lead-Bismuth Eutectic (LBE) cooled experimental ADS (XADS), both to assess its behaviour during operational and accident sequences and to provide input data for the thermal-mechanical analyses. It also reports a description of modifications properly implemented in the codes used for the assessment of this kind of plants. (author)

  11. MEGAPIE analytical support task : characterization of lead-bismuth eutectic and sodium-cooled tungsten target materials for accelerator driven systems

    International Nuclear Information System (INIS)

    Gohar, Y.

    2002-01-01

    Lead-Bismuth Eutectic and Tungsten are under consideration as target materials with high-energy protons for generating neutrons to drive actinide and fission product transmuters. A detailed characterization has been performed to study the performance of these target materials as a function of the main variables and the design selections. The characterization includes the neutron yield, the spatial energy deposition, the neutron spectrum, the beam window performance, and the target buffer impact on the target performance. The characterization has also considered high-energy deuteron particles to study the impact on the target neutronic performance. The obtained results quantify the performance of the Lead-Bismuth Eutectic and Tungsten target materials as a function of the target variables and design selections

  12. Post-irradiation analysis of an ISOLDE lead-bismuth target: Stable and long-lived noble gas nuclides

    Energy Technology Data Exchange (ETDEWEB)

    Leya, I., E-mail: Ingo.Leya@space.unibe.ch [University of Bern, Space Science and Planetology, Bern (Switzerland); Grimberg, A. [University of Bern, Space Science and Planetology, Bern (Switzerland); Isotope Geochemistry, ETH Zürich, Zürich (Switzerland); David, J.-C. [CEA/Saclay, Irfu/SPhN, 91191 Gif-sur-Yvette, Cedex (France); Schumann, D.; Neuhausen, J. [Paul Scherrer Institut, Villigen (Switzerland); Zanini, L. [Paul Scherrer Institut, Villigen (Switzerland); European Spallation Source ESS AB, P.O. Box 117, SE-22100 Lund (Sweden); Noah, E. [University of Geneva, Département de Physique Nucléaire et Corpusculaire, Geneve (Switzerland)

    2016-07-15

    We measured the isotopic concentrations of long-lived and stable He, Ne, Ar, Kr, and Xe isotopes in a sample from a lead-bismuth eutectic target irradiated with 1.0 and 1.4 GeV protons. Our data indicate for most noble gases nearly complete release with retention fractions in the range of percent or less. Higher retention fractions result from the decay of long-lived radioactive progenitors from groups 1, 2, or 7 of the periodic table. From the data we can calculate a retention fraction for {sup 3}H of 2–3%. For alkaline metals we find retention fractions of about 10%, 30%, and 50% for Na, Rb, and Cs, respectively. For the alkaline earth metal Ba we found complete retention. Finally, the measured Kr and Xe concentrations indicate that there was some release of the halogens Br and I during and/or after the irradiation.

  13. The design of a lead-bismuth target system with a dual injection tube

    International Nuclear Information System (INIS)

    Cho, C.H.; Kim, Y.; Song, T.Y.; Park, W.S.

    2005-01-01

    A spallation target system is a key component to be developed for an accelerator driven system (ADS). It is known that a 15 ∼ 25 MW spallation target is required for a practical 1000 MWth ADS. The design of a 20 MW spallation target is very challenging because more than 60% of the beam power is deposited as heat in a small volume of the target system. In the present work, a numerical design study was performed to obtain the optimal design parameters for a 20 MW spallation target for a 1000 MW ADS. A dual injection tube was proposed for the reduction of the LBE flow rate at the target channel. The results of the present study show that a 30 cm wide proton beam with a uniform beam distribution should be adopted for the spallation target of a 20 MW power. When the dual LBE injection tube is employed, the LBE flow rate could be reduced by a factor of 4 without reducing the maximum allowable beam current. (authors)

  14. Thermal-hydraulics investigations for the Liquid Lead-Bismuth Target of the SINQ spallation source

    International Nuclear Information System (INIS)

    Sigg, B.; Dury, T.; Hudina, M.; Smith, B.

    1991-01-01

    The paper contains a discussion of the thermal-hydraulic problems of the target which require detailed analysis by means of a two- or three-dimensional space- and in part also time-dependent fluid dynamics code. There follows a short description of the general-purpose code ASTEC, which is being used for these investigations, and examples of the target modelling, including results. The final part of the paper is devoted to a short discussion of experiments against which this application of the code has to be validated. (author)

  15. Near target residues from the peripheral interaction of relativistic heavy ions with bismuth

    International Nuclear Information System (INIS)

    Aleklett, K.; Morrissey, D.J.; Loveland, W.; Moody, K.; Seaborg, G.T.

    1979-01-01

    Isotopic distributions for the near target residues Au and Tl were measured radioanalytically for the reaction of 8.0-GeV 20 Ne ions with 209 Bi. The isotopic production cross section for Au and Tl isotopes were calculated by using a macroscopic abrasion-ablation model and a microscopic intranuclear cascade-evaporation model. The importance of the neutron skin in determining the yield of these products from the peripheral interactions was also explored in the framework of the macroscopic model. 3 figures

  16. Measurement of Gas and Volatile Elements Production Cross Section in a Molten Lead-Bismuth Target

    CERN Multimedia

    2002-01-01

    MEGAPIE is a project for a 1 MW liquid PbBi spallation source, to be built at the SINQ facility at the Paul Scherrer Institut, which will be an important step in the roadmap towards the demonstration of the ADS concept and high power molten metal targets in general. In the design and construction of such a challenging project it is extremely important to evaluate the amount and type of gas and volatile elements which will be produced, for a reliable and safe operation of the experiment. Both stable (H, $^{4}$He and other noble gases) and radioactive isotopes are of interest. Currently, different design options are under consideration to deal with the gas produced during operation. \\\\ For a correct estimation of the production cross sections, a measurement with a liquid PbBi target and a proton beam of energy close to the one of MEGAPIE (575 MeV) is necessary. We would like to use the ISOLDE facility, which offers the unique opportunity via its mass spectrometric analysis of the elements present in the gas pha...

  17. Targeted alpha therapy of mCRPC. Dosimetry estimate of {sup 213}bismuth-PSMA-617

    Energy Technology Data Exchange (ETDEWEB)

    Kratochwil, Clemens; Afshar-Oromieh, Ali; Rathke, Hendrik; Giesel, Frederik L. [University Hospital Heidelberg, Department of Nuclear Medicine, Heidelberg (Germany); Schmidt, Karl [ABX-CRO, Dresden (Germany); Bruchertseifer, Frank; Morgenstern, Alfred [European Commission - Joint Research Centre, Directorate for Nuclear Safety and Security, Karlsruhe (Germany); Haberkorn, Uwe [University Hospital Heidelberg, Department of Nuclear Medicine, Heidelberg (Germany); German Cancer Research Center (DKFZ), Cooperation Unit Nuclear Medicine, Heidelberg (Germany)

    2018-01-15

    PSMA-617 is a small molecule targeting the prostate-specific membrane antigen (PSMA). In this work, we estimate the radiation dosimetry for this ligand labeled with the alpha-emitter {sup 213}Bi. Three patients with metastatic prostate cancer underwent PET scans 0.1 h, 1 h, 2 h, 3 h, 4 h and 5 h after injection of {sup 68}Ga-PSMA-617. Source organs were kidneys, liver, spleen, salivary glands, bladder, red marrow and representative tumor lesions. The imaging nuclide {sup 68}Ga was extrapolated to the half-life of {sup 213}Bi. The residence times of {sup 213}Bi were forwarded to the instable daughter nuclides. OLINDA was used for dosimetry calculation. Results are discussed in comparison to literature data for {sup 225}Ac-PSMA-617. Assuming a relative biological effectiveness of 5 for alpha radiation, the dosimetry estimate revealed equivalent doses of mean 8.1 Sv{sub RBE5}/GBq for salivary glands, 8.1 Sv{sub RBE5}/GBq for kidneys and 0.52 Sv{sub RBE5}/GBq for red marrow. Liver (1.2 Sv{sub RBE5}/GBq), spleen (1.4 Sv{sub RBE5}/GBq), bladder (0.28 Sv{sub RBE5}/GBq) and other organs (0.26 Sv{sub RBE5}/GBq) were not dose-limiting. The effective dose is 0.56 Sv{sub RBE5}/GBq. Tumor lesions were in the range 3.2-9.0 Sv{sub RBE5}/GBq (median 7.6 Sv{sub RBE5}/GBq). Kidneys would limit the cumulative treatment activity to 3.7 GBq; red marrow might limit the maximum single fraction to 2 GBq. Despite promising results, the therapeutic index was inferior compared to {sup 225}Ac-PSMA-617. Dosimetry of {sup 213}Bi-PSMA-617 is in a range traditionally considered reasonable for clinical application. Nevertheless, compared to {sup 225}Ac-PSMA-617, it suffers from higher perfusion-dependent off-target radiation and a longer biological half-life of PSMA-617 in dose-limiting organs than the physical half-life of {sup 213}Bi, rendering this nuclide as a second choice radiolabel for targeted alpha therapy of prostate cancer. (orig.)

  18. Pathways for the release of polonium from a lead-bismuth spallation target (thermochemical calculation); Verfluechtigungspfade des Poloniums aus einem Pb-Bi-Spallationstarget (Thermochemische Kalkulation)

    Energy Technology Data Exchange (ETDEWEB)

    Eichler, B.; Neuhausen, J

    2004-06-01

    An analysis of literature data for the thermochemical constants of polonium reveals considerable discrepancies in the relations of these data among each other as well as in their expected trends within the chalcogen group. This fact hinders a reliable assessment of possible reaction paths for the release of polonium from a liquid lead-bismuth spallation target. In this work an attempt is made to construct a coherent data set for the thermochemical properties of polonium and some of its compounds that are of particular importance with respect to the behaviour of polonium in a liquid Pb-Bi target. This data set is based on extrapolations using general trends throughout the periodic table and, in particular, within the chalcogen group. Consequently, no high accuracy should be attributed to the derived data set. However, the data set derived in this work is consistent with definitely known experimental data. Furthermore, it complies with the general trends of physicochemical properties within the chalcogen group. Finally, well known relations between thermochemical quantities are fulfilled by the data derived in this work. Thus, given the lack of accurate experimental data it can be regarded as best available data. Thermochemical constants of polonium hydride, lead polonide and polonium dioxide are derived based on extrapolative procedures. Furthermore, the possibility of formation of the gaseous intermetallic molecule BiPo, which has been omitted from discussion up to now, is investigated. From the derived thermochemical data the equilibrium constants of formation, release and dissociation reactions are calculated for different polonium containing species. Furthermore equilibrium constants are determined for the reaction of lead polonide and polonium dioxide with hydrogen, water vapour and the target components lead and bismuth. The most probable release pathways are discussed. From thermochemical evaluations polonium is expected to be released from liquid lead-bismuth

  19. Measurements of gas and volatile element production rates from an irradiated molten lead and lead-bismuth spallation target with proton beams of 1 and 1.4 GeV

    International Nuclear Information System (INIS)

    Tall, Y.

    2008-03-01

    The integrated project EUROTRANS (European Research Programme for the Transmutation of High Level Nuclear Waste in an Accelerator Driven System) of the 6. EURATOM Framework Programme aims to demonstrate the transmutation of radioactive waste in ADS (Accelerator Driven Sub-critical system). It will carry out a first advanced design of an experimental facility to demonstrate the technical feasibility of transmutation, and will produce a conceptual design of an industrial facility dedicated to transmutation. An ADS consists of three fundamental elements: the accelerator of protons, the sub-critical core and the spallation target. SUBATECH (physique Sub-Atomique et des Technologies associees) laboratory is involved to the study of the chosen liquid lead-bismuth as a spallation ADS target. The irradiation of liquid lead-bismuth target with energetic proton beam generates in addition to neutrons, volatile and radioactive residues. In order to determine experimentally the production rates of gas and volatile elements following a spallation reaction in a lead-bismuth target, the experiment IS419 was performed at the ISOLDE facility at CERN (Centre Europeen de la Recherche Nucleaire). This experiment constitutes the frame of the thesis whose main objective is to assess and study the production and release rates of many gas and volatile element from the irradiated lead-bismuth target with an energetic proton beam. The obtained data are compared to Monte Carlo simulation code (MCNPX) results in order to test the intranuclear cascade model of Bertini and of Cugnon, and the evaporation options of Dresner and Schmidt. (author)

  20. Comparative analysis of CD138 antigen targeting for the treatment of multiple myeloma with bismuth-213 and Melphalan chemotherapy

    International Nuclear Information System (INIS)

    Gouard, S.; Gaschet, J.; Maurel, C.; Barbet, J.; Davodeau, F.; Pallardy, A.; Faivre-Chauvet, A.; Kraeber-Bodere, F.; Bruchertseifer, F.; Morgenstern, A.; Cherel, M.

    2015-01-01

    Full text of publication follows. Aim: multiple myeloma (MM) is a B-cell malignancy of terminally differentiated plasma cells within the bone marrow, with the presence of a monoclonal immunoglobulin in serum and/or urine and development of osteolytic bone lesions in human. Despite intense research to develop new treatments, cure is almost never achieved. Alpha-radioimmunotherapy (RIT) has been shown to be effective in vivo in a multiple myeloma model and seems particularly suited for disseminated tumour cells or small clusters of tumour cells. CD138 (Syndecan-1) is found mainly in epithelial cells, but has been shown to be expressed by most myeloma cells, both in human and in mouse. In order to define where alpha RIT stands in MM treatment, the aim of this study was to compare Melphalan, MM standard treatment, with alpha RIT using a bismuth-213-labelled anti-mouse CD138 rat antibody in a syngeneic mouse MM model. Material and Methods: C57BL/KaLwRij mice were grafted with 10 6 5T33 cells (murine myeloma cells). Luciferase transfected 5T33 were used for in vivo localization of the cells during the course of disease. The first step of the study was to assess the dose-response of Melphalan (100, 200 et 300 μg/mouse), 21 days after engraftment. The second step consisted in therapeutic association: Melphalan followed by RIT at d22 et d25 after engraftment. Toxicity (animal weight, blood cell counts) and treatment efficacy were studied in animals receiving no treatment, injected with Melphalan alone (200 μg), RIT alone at d22 and d25 (3.7 MBq of 213 Bi-anti-CD138) and Melphalan combined with alpha RIT. Results: fifty percent of untreated mice died by d64 after MM engraftment. In mice treated with Melphalan alone, only the 200 μg dose improved median survival. No animal was cured after Melphalan treatment whereas 60% of the mice survived with RIT alone at d22 after tumour engraftment. However, the therapeutic window seems to be narrow, indeed no effect was observed with

  1. Study of Target Fragmentation in the Interaction of 86 MeV/A $^{12}$Carbon with Tantalum, Bismuth and Uranium

    CERN Multimedia

    2002-01-01

    Using radiochemical techniques we will ; a)~~measure the target fragment mass and charge distributions from the interaction of 86~MeV/A |1|2C with Ta, Bi and U; ; b)~~measure the target fragment forward momentum and average kinetic energy using the thick target-thick catcher technique for the above reactions; and ; c)~~measure the target fragment angular and differential energy distributions using thin target-thin catcher techniques for the reactions with Ta and U. \\\\ \\\\ These measurements should allow us to better characterize the transition between low energy and realistic heavy ion reaction mechanisms.

  2. Advisory group meeting on design and performance of reactor and subcritical blanket systems with lead and lead-bismuth as coolant and/or target material. Working material

    International Nuclear Information System (INIS)

    2001-01-01

    The purpose of the IAEA Advisory Group Meeting (AGM) on Design and Performance of Reactor and Sub-critical Blanket Systems with Lead and Lead-Bismuth as Coolant and/or Target Material was to provide a forum for international information exchange on all the topics relevant to Pb and Pb/Bi cooled critical and sub-critical reactors. In addition, the AGM aimed at: (1) finding ways and means to improve international co-ordination efforts in this area; (2) obtaining advice from the Member States with regard to the activities to be implemented in this area by the IAEA, in order to best meet their needs; and (3) laying out the plans for an effective co-ordination and support of the R and D activities in this area. The AGM stressed that nuclear energy is a realistic solution to satisfy the energy demand, considering the limited resources of fossil fuel, its uneven distribution in the world and the impact of its use on the planet, and taking into account the expected doubling of the world population in the 21st century and tripling of the electricity demand (especially in the developing countries). However, the AGM concluded that the development of an innovative nuclear technology meeting the following requirements must be pursued: (a) deterministic exclusion of any severe accident; (b) proliferation resistance; (c) cost competitiveness with alternative energy sources; (d) sustainable fuel supply; and (e) solution of the radioactive waste management problem

  3. K-shell excitation studied for H- and He-like bismuth ions in collisions with low-z target atoms

    International Nuclear Information System (INIS)

    Stoehlker, T.; Bosch, F.; Geissel, H.; Kozhuharov, C.; Ludziejewski, T.; Mokler, P.H.; Scheidenberger, C.; Stachura, Z.; Warczak, A.

    1997-09-01

    The formation of excited projectile states via Coulomb excitation is investigated for hydrogen- and helium-like bismuth projectiles (Z=83) in relativistic ion-atom collisions. The excitation process was unambiguously identified by observing the radiative decay of the excited levels to the vacant 1s shell in coincidence with ions that did not undergo charge exchange in the reaction target. In particular, owing to the large fine structure splitting of Bi, the excitation cross-sections to the various L-shell sublevels are determined separately. The results are compared with detailed relativistic calculations, showing that both the relativistic character of the bound-state wave-functions and the magnetic interaction are of considerable importance for the K-shell excitation process in high-Z ions like Bi. The experimental data confirm the result of the complete relativistic calculations, namely that the magnetic part of the Lienard-Wiechert interaction leads to a significant reduction of the K-shell excitation cross-section. (orig.)

  4. Measurements of gas and volatile element production rates from an irradiated molten lead and lead-bismuth spallation target with proton beams of 1 and 1.4 GeV; Mesures de taux de production d'elements gazeux et volatiles lors de reactions induites par des protons de 1 et 1,4 GeV sur des cibles epaisses de plomb et plomb-bismuth liquides

    Energy Technology Data Exchange (ETDEWEB)

    Tall, Y

    2008-03-15

    The integrated project EUROTRANS (European Research Programme for the Transmutation of High Level Nuclear Waste in an Accelerator Driven System) of the 6. EURATOM Framework Programme aims to demonstrate the transmutation of radioactive waste in ADS (Accelerator Driven Sub-critical system). It will carry out a first advanced design of an experimental facility to demonstrate the technical feasibility of transmutation, and will produce a conceptual design of an industrial facility dedicated to transmutation. An ADS consists of three fundamental elements: the accelerator of protons, the sub-critical core and the spallation target. SUBATECH (physique Sub-Atomique et des Technologies associees) laboratory is involved to the study of the chosen liquid lead-bismuth as a spallation ADS target. The irradiation of liquid lead-bismuth target with energetic proton beam generates in addition to neutrons, volatile and radioactive residues. In order to determine experimentally the production rates of gas and volatile elements following a spallation reaction in a lead-bismuth target, the experiment IS419 was performed at the ISOLDE facility at CERN (Centre Europeen de la Recherche Nucleaire). This experiment constitutes the frame of the thesis whose main objective is to assess and study the production and release rates of many gas and volatile element from the irradiated lead-bismuth target with an energetic proton beam. The obtained data are compared to Monte Carlo simulation code (MCNPX) results in order to test the intranuclear cascade model of Bertini and of Cugnon, and the evaporation options of Dresner and Schmidt. (author)

  5. Experimental study of the features of the running part liquid metal target on lead-bismuth alloy

    International Nuclear Information System (INIS)

    Beznosov, A.V.; Meluzov, A.G.; Novozhilova, O.O.; Efanov, A.D.

    2007-01-01

    The results of experimental investigations of the through part of a full-scale liquid metal target of an accelerator-control system, where the working cavity of the target communicates directly with the particle accelerator cavity, are presented. Two design variants were investigated - with vertical and horizontal orientation of the target axis in space and spinning of the flow in front of the nozzle adapter located in front of the entrance of the eutectic into the working cavity of the target. The profiles obtained for the free coolant surface with liquid metal flowing through vertically and horizontally positioned targets are presented. It is confirmed that when the pressure of the free surface of the liquid metal corresponds to the pressure in the accelerator cavity it is possible that liquid metal will not flow into the cavity simulating the connecting piece for inflow of accelerated particles with the piece oriented vertically or horizontally [ru

  6. Volatile elements production rates in a 1.4 Gev proton-irradiated molten lead-bismuth target

    CERN Document Server

    Zanini, L; Everaerts, P; Fallot, M; Franberg, H; Gröschel, F; Jost, C; Kirchner, T; Kojima, Y; Köster, U; Lebenhaft, J; Manfrina, E; Pitcher, E J; Ravn, H L; Tall, Y; Wagner, W; Wohlmuther, M

    2005-01-01

    Production rates of volatile elements following spallation reaction of 1.4 GeV protons on a liquid Pb/Bi target have been measured. The experiment was performed at the ISOLDE facility at CERN. These data are of interest for the developments of targets for accelerator driven systems such as MEGAPIE. Additional data have been taken on a liquid Pb target. Calculations were performed using the FLUKA and MCNPX Monte Carlo codes coupled with the evolution codes ORIHET3 and FISPACT using different options for the intra-nuclear cascades and evaporation models. Preliminary results from the data analysis show good comparison with calculations for Hg and for noble gases. For other elements such as I it is apparent that only a fraction of the produced isotopes is released. The agreement with the experimental data varies depending on the model combination used. The best results are obtained using MCNPX with the INCL4/ABLA models and with FLUKA. Discrepancies are found for some isotopes produced by fission using the MCNPX ...

  7. MicroRNA-210 regulates mitochondrial free radical response to hypoxia and krebs cycle in cancer cells by targeting iron sulfur cluster protein ISCU.

    Directory of Open Access Journals (Sweden)

    Elena Favaro

    2010-04-01

    Full Text Available Hypoxia in cancers results in the upregulation of hypoxia inducible factor 1 (HIF-1 and a microRNA, hsa-miR-210 (miR-210 which is associated with a poor prognosis.In human cancer cell lines and tumours, we found that miR-210 targets the mitochondrial iron sulfur scaffold protein ISCU, required for assembly of iron-sulfur clusters, cofactors for key enzymes involved in the Krebs cycle, electron transport, and iron metabolism. Down regulation of ISCU was the major cause of induction of reactive oxygen species (ROS in hypoxia. ISCU suppression reduced mitochondrial complex 1 activity and aconitase activity, caused a shift to glycolysis in normoxia and enhanced cell survival. Cancers with low ISCU had a worse prognosis.Induction of these major hallmarks of cancer show that a single microRNA, miR-210, mediates a new mechanism of adaptation to hypoxia, by regulating mitochondrial function via iron-sulfur cluster metabolism and free radical generation.

  8. Power reactors and sub-critical blanket systems with lead and lead-bismuth as coolant and/or target material. Utilization and transmutation of actinides and long lived fission products

    International Nuclear Information System (INIS)

    2003-05-01

    High level radioactive waste disposal is an issue of great importance in the discussion of the sustainability of nuclear power generation. The main contributors to the high radioactivity are the fission products and the minor actinides. The long lived fission products and minor actinides set severe demands on the arrangements for safe waste disposal. Fast reactors and accelerator driven systems (ADS) are under development in Member States to reduce the long term hazard of spent fuel and radioactive waste, taking advantage of their incineration and transmutation capability. Important R and D programmes are being undertaken in many Member States to substantiate this option and advance the basic knowledge in this innovative area of nuclear energy development. The conceptual design of the lead cooled fast reactor concept BREST-OD-300, as well as various other conceptual designs of lead/lead-bismuth cooled fast reactors have been developed to meet enhanced safety and non-proliferation requirements, aiming at both energy production and transmutation of nuclear waste. Some R and D studies indicate that the use of lead and lead-bismuth coolant has some advantages in comparison with existing sodium cooled fast reactor systems, e.g.: simplified design of fast reactor core and BOP, enhanced inherent safety, and easier radwaste management in related fuel cycles. Moreover, various ADS conceptual designs with lead and lead-bismuth as target material and coolant also have been pursued. The results to date are encouraging, indicating that the ADS has the potential to offer an option for meeting the challenges of the back end fuel cycle. During the last decade, there have been substantial advances in several countries with their own R and D programme in the fields of lead/lead-bismuth cooled critical and sub-critical concepts. coolant technology, and experimental validation. In this context, international exchange of information and experience, as well as international

  9. Laser Spectroscopy of Neutron Rich Bismuth Isotopes

    CERN Multimedia

    2002-01-01

    %IS344 :\\\\ \\\\ The aim of the experiment is to measure the optical isotope shifts and hyperfine structures of bismuth isotopes across the N=126 shell closure in order to extract the change in mean square charge radii ($\\delta\\langle r^{2}\\rangle$) and static moments. These include the first isotones of lead to be measured directly above the shell closure and will provide new information on the systematics of the kink ($\\delta\\langle r^{2}\\rangle)$ seen in the lead isotopic chain. After two very successful runs the programme has been extended to include the neutron deficient isotopes below $^{201}$Bi to study the systematics across the $i_{13/2}$ neutron sub-shell closure at N=118.\\\\ \\\\ During the initial 2 runs (9 shifts) the isotope shifts and hyperfine structures of three new isotopes, $ ^{210,212,213}$Bi and the 9$^{-}$ isomer of $^{210}$Bi have been measured. The accuracy of the previous measurements of $^{205,206,208}$Bi have been greatly improved. The samples of $ ^{208,210,210^{m}}$Bi were prepared by c...

  10. Valley polarization in bismuth

    Science.gov (United States)

    Fauque, Benoit

    2013-03-01

    The electronic structure of certain crystal lattices can contain multiple degenerate valleys for their charge carriers to occupy. The principal challenge in the development of valleytronics is to lift the valley degeneracy of charge carriers in a controlled way. In bulk semi-metallic bismuth, the Fermi surface includes three cigar-shaped electron valleys lying almost perpendicular to the high symmetry axis known as the trigonal axis. The in-plane mass anisotropy of each valley exceeds 200 as a consequence of Dirac dispersion, which drastically reduces the effective mass along two out of the three orientations. According to our recent study of angle-dependent magnetoresistance in bismuth, a flow of Dirac electrons along the trigonal axis is extremely sensitive to the orientation of in-plane magnetic field. Thus, a rotatable magnetic field can be used as a valley valve to tune the contribution of each valley to the total conductivity. As a consequence of a unique combination of high mobility and extreme mass anisotropy in bismuth, the effect is visible even at room temperature in a magnetic field of 1 T. Thus, a modest magnetic field can be used as a valley valve in bismuth. The results of our recent investigation of angle-dependent magnetoresistance in other semi-metals and doped semiconductors suggest that a rotating magnetic field can behave as a valley valve in a multi-valley system with sizeable mass anisotropy.

  11. Application of SIMS to the study of selective deposition of trace amounts of lead and bismuth from solution onto the metals nickel and silver

    International Nuclear Information System (INIS)

    Smith, D.; Peck, G.

    1996-01-01

    Full text: The natural 233 U decay series includes the trio 210 Pb, 210 Bi and 210 Po. These are useful in estimating rates of environmental processes and 210 Po is a major contributor to the radiation dose of marine organisms. To develop an understanding of the distribution of these closely related radionuclides in the environment it is necessary to be able to measure all three. Accurate measurements depend on preliminary separation of the nuclides. Isolation and measurement of 210 Bi has been a continuing problem and this has restricted the study of the role of this nuclide in environmental processes. We have developed a sample preparation that includes plating polonium from solution onto a silver disc then plating bismuth onto a nickel disc and leaving the lead in solution. The 210 Bi is measured by Cerenkov counting. Any 210 Pb plating onto nickel with the bismuth would interfere in subsequent counting as it decays rapidly to 210 Bi. We have used SIMS (Secondary Ion Mass Spectrometry) to measure bismuth and lead deposited on the nickel and silver discs. This is possible because the stable isotopes of the four elements do not overlap. SIMS is especially appropriate for this study as the Bi and Pb deposited as thin films on the metal surface. Careful selection of experimental conditions allowed quantitative measurements of lead and bismuth without mutual interference. The results have been used in developing plating conditions that optimise separation of lead and bismuth

  12. Bismuth toxicity in patients treated with bismuth iodoform paraffin packs.

    Science.gov (United States)

    Atwal, A; Cousin, G C S

    2016-01-01

    Bismuth is a heavy metal used in bismuth iodoform paraffin paste (BIPP) antiseptic dressings and in a number of other medical preparations. It can be absorbed systemically and cause toxicity. We report 2 cases of such neurotoxicity after it was used in operations on the jaws. Copyright © 2015. Published by Elsevier Ltd.

  13. Radiochemical determination of lead-210 in uranium ores and air dusts

    International Nuclear Information System (INIS)

    Sill, C.W.; Willis, C.P.

    1977-01-01

    An improved procedure is described by which cellulose, glass fiber, and polystyrene filters can be wet-ashed and siliceous samples dissolved completely without loss of lead by either volatilization or spontaneous reduction to metal that occurs with dry ashing and/or treatment in platinum containers. The solution of bismuth-210 used to calibrate the β counter is prepared by chemical separation from a solution of lead-210 which is much more convenient and results in a product of higher specific activity than one prepared by neutron activation of stable bismuth. After separation from the samples by conventional chemical procedures, the bismuth-210 is precipitated on barium sulfate for β counting which is more convenient and gives a more uniform and reproducible deposit than is obtained by most other means

  14. Void worths in subcritical cores cooled by lead-bismuth

    International Nuclear Information System (INIS)

    Wallenius, Janne; Tucek, Kamil; Gudowski, Waclaw

    2001-01-01

    The introduction lead-bismuth coolant in accelerator driven transmutation systems (ADS) was: good neutron economy (higher source efficiency); natural circulation possible (decay heat removal); synergy with spallation target (simplified coolant management); high temperature of boiling (larger overpower margin); smaller void worths (operation at higher k-values). This paper deals with different aspects of the void worths in JAERI ADS

  15. An acclerator-based installation of small power with the lead-bismuth coolant

    Energy Technology Data Exchange (ETDEWEB)

    Gorshkov, V.T.; Yefimov, E.I.; Novikova, N.N. [Research and Development Bereau, Podolsk (Russian Federation)] [and others

    1995-10-01

    The structure of the accelerator-based installation is described that includes the subcritical reactor-blanket with power 15 MW(h) cooled with lead-bismuth, the lead-bismuth flow target where a beam of {alpha}-particle is injected, the equipment of a primary and secondary curcuits. Some results of calculations and estimations are discussed that have been carried out to justify the target and blanket constructions. Some main characteristics of the installation are presented.

  16. 210Po and 210Pb levels in mussels and fish from Slovenian market and the related dose assessment

    International Nuclear Information System (INIS)

    Planinšek, Petra; Smodiš, Borut; Benedik, Ljudmila

    2013-01-01

    Polonium-210 (t 1/2 = 138 d) is a decay product of uranium-radium decay chain and consequently widely spread in the environment. It enters organisms through direct uptake, ingestion or inhalation. It is a pure alpha emitter and its radiotoxicity is connected with the fact that emits alpha particles with relatively high energy of about 5.3 MeV. It is concentrated in the soft tissues such as mussel, liver and others, where significantly contributes to the internal dose. Beta emitter lead-210 (t 1/2 = 22.17 years) is the second highest radiotoxic radionuclide from uranium-238 decay chain and decays, through bismuth- 210 (t 1/2 = 5.01 d) into 210 Po. Therefore it is necessary to determine the 21P o in foods, especially in seafood, because of its accumulation capacity. 210 Po and 210 Pb were determined in mussels (Mytilus galloprovincialis) and fish (salmon, trout) from Slovenia market. Mussels were bought on the local market as well as from domestic producers. Fish of Slovenian origin were bought on the local market. Samples were freeze dried, homogenized and assayed for 210 Po and 210 Pb. First, radiochemical separation was performed, followed by alpha particle spectrometric measurement of 210 Po and beta counting of 210 Pb on a low background gas-flow proportional counter. The results obtained show that the activity concentrations of 210 Po in mussels varied from 0.9 to 191 Bq/kg of fresh mass and for fish from 0.3 to 2.12 Bq/kg of fresh mass, while for 210 Pb they varied from 1.5 to 6.9 Bq/k of fresh mass for mussels and in fish samples the activity concentrations were less than 1.9 Bq/kg of fresh mass. Combined annual ingestion doses due to 210 Po and 210 Pb for mussels and fish from the Slovenian market is assessed. (author)

  17. Characteristics of polonium contamination from neutral irradiated lead-bismuth eutectic

    International Nuclear Information System (INIS)

    Miura, T.; Obara, T.; Sekimoto, H.

    2004-01-01

    After neutron capture, bismuth-209 changes to polonium-210 that emits α-particles. Lead-Bismuth eutectic (LBE) in reactor system contaminates the system by polonium. We analyzed adsorbed materials from melted LBE on quartz glass plate. Lead, bismuth and their oxides were confirmed in adsorbed materials. And, we evaluated the baking method in vacuum for removal of polonium and adsorbed materials on quartz glass plate. It was evaluated that it is possible to remove almost all the polonium from the quartz glass plate by baking at temperature more than 300 C. degrees. Unfolding method was applied to calculate polonium distribution in LBE ingot. From measured α-particle pulse height distribution, the polonium distribution in depth of LBE ingot was calculated using quadratic programming code, where response functions are calculated by Monte Carlo method. (authors)

  18. Equilibrium evaporation behavior of polonium and its homologue tellurium in liquid lead-bismuth eutectic

    International Nuclear Information System (INIS)

    Ohno, Shuji; Miyahara, Shinya; Kurata, Yuji; Katsura, Ryoei; Yoshida, Shigeru

    2006-01-01

    Experimental study using the transpiration method investigates equilibrium evaporation behavior of radionuclide polonium ( 210 Po) generated and accumulated in liquid lead-bismuth eutectic (LBE) cooled nuclear systems. The experiment consists of two series of tests: preliminary evaporation tests for homologue element tellurium (Te) in LBE, and evaporation tests for 210 Po-accumulated LBE in which test specimens are prepared by neutron irradiation. The evaporation tests of Te in LBE provide the suggestion that Te exists in a chemical form of PbTe as well as the information for confirming the validity of technique and conditions of Po test. From the evaporation tests of 210 Po in LBE, we obtain fundamental data and empirical equations such as 210 Po vapor concentration in the gas phase, 210 Po partial vapor pressure, thermodynamic activity coefficients, and gas-liquid equilibrium partition coefficient of 210 Po in LBE in the temperature range from 450 to 750degC. Additionally, radioactivity concentration of 210 Po and 210m Bi vapor in a cover gas region of a typical LBE-cooled nuclear system is specifically estimated based on the obtained experimental results, and the importance of 210 Po evaporation behavior is quantitatively demonstrated. (author)

  19. Lead-210 and polonium-210 in grass

    Energy Technology Data Exchange (ETDEWEB)

    Hill, C R

    1960-07-16

    It appears that an important contribution to the observed ..cap alpha..-activity of grass may be provided by a process of natural fall-out in which lead-210 resulting from decay of atmospheric radon, together with a fraction of the equilibrium amount of its descendant polonium-210 are deposited by rainfall directly on to foliage. Metabolic uptake of part of this activity by sheep is indicated by the presence in the kidney of polonium-210. 6 references, 1 figure, 2 tables.

  20. Short-term static corrosion tests in lead-bismuth

    Science.gov (United States)

    Soler Crespo, L.; Martín Muñoz, F. J.; Gómez Briceño, D.

    2001-07-01

    Martensitic steels have been proposed to be used as structural materials and as spallation target window in hybrid systems devoted to the transmutation of radioactive waste of long life and high activity. However, their compatibility with lead-bismuth in the operating conditions of these systems depends on the existence of a protective layer such as an oxide film. The feasibility of forming and maintaining an oxide layer or maintaining a pre-oxidised one has been studied. Martensitic steel F82Hmod. (8% Cr) has been tested in lead-bismuth under static and isothermal conditions at 400°C and 600°C. In order to study the first stages of the interaction between the steel and the eutectic, short-term tests (100 and 665 h) have been carried out. Pre-oxidised and as-received samples have been tested in atmospheres with different oxidant potential. For low oxygen concentration in lead-bismuth due to unexpected oxygen consumption in the experimental device, dissolution of as-received F82Hmod. occurs and pre-oxidation does not prevent the material dissolution. For high oxygen concentration, the pre-oxidation layer seems to improve the feasibility of protecting stainless steels controlling the oxygen potential of lead-bismuth with a gas phase.

  1. Short-term static corrosion tests in lead-bismuth

    International Nuclear Information System (INIS)

    Soler Crespo, L.; Martin Munoz, F.J.; Gomez Briceno, D.

    2001-01-01

    Martensitic steels have been proposed to be used as structural materials and as spallation target window in hybrid systems devoted to the transmutation of radioactive waste of long life and high activity. However, their compatibility with lead-bismuth in the operating conditions of these systems depends on the existence of a protective layer such as an oxide film. The feasibility of forming and maintaining an oxide layer or maintaining a pre-oxidised one has been studied. Martensitic steel F82Hmod. (8% Cr) has been tested in lead-bismuth under static and isothermal conditions at 400 o C and 600 o C. In order to study the first stages of the interaction between the steel and the eutectic, short-term tests (100 and 665 h) have been carried out. Pre-oxidised and as-received samples have been tested in atmospheres with different oxidant potential. For low oxygen concentration in lead-bismuth due to unexpected oxygen consumption in the experimental device, dissolution of as-received F82Hmod. occurs and pre-oxidation does not prevent the material dissolution. For high oxygen concentration, the pre-oxidation layer seems to improve the feasibility of protecting stainless steels controlling the oxygen potential of lead-bismuth with a gas phase

  2. Decay studies of a long lived high spin isomer of 210Bi

    International Nuclear Information System (INIS)

    Tuggle, D.G.

    1976-08-01

    A source of approximately 30 μg of pure (> 90%) /sup 210m/Bi (Jπ = 9-) was prepared by irradiating 209 Bi in a nuclear reactor. After chemical separations to remove 210 Po from the irradiated bismuth sample were completed, the 210 Bi was electromagnetically separated from the 209 Bi by a series of two isotope separations to create the source mentioned above. This source was then used to conduct alpha, conversion electron, gamma, gamma-gamma coincidence, and alpha-gamma coincidence spectroscopic studies of the decay of /sup 210m/Bi. The partial half life for the alpha decay of /sup 210m/Bi was measured as 3.0 x 10 6 yr. A lower limit of 10 13 years was set for the partial half life for the decay of /sup 210m/Bi to 210 Po. Alpha decay of /sup 210m/Bi to 8 excited states of 206 Tl was observed. A lower limit of 10 -4 % was set for the branching ratio of the parity forbidden alpha decay of 210 Bi to the 206 Ti ground state. Theoretical decay rates for the alpha decays of /sup 210m/Bi, 210 Bi, 211 Po, and /sup 211m/Po were calculated using the method developed by Hans Mang. A comparison of the calculated and experimentally measured alpha decay rates of /sup 210m/Bi showed good agreement for the relative alpha decay rates

  3. Iodine Gas Trapping using Granular Porous Bismuth

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Jae Hwan; Shin, Jin Myeong; Park, Jang Jin; Park, Geun Il [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Yim, Mansung [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

    2014-05-15

    {sup 129}I is a radionuclide with a very long half-life of 1.57 Χ 10{sup 7} years and has negative health effects to the human body. Therefore, the emission of {sup 129}I into the air is closely regulated by the Environmental Protection Agency (EPA). Many methods for trapping gaseous {sup 129}I have been developed thus far, including wet scrubbing and adsorption using silver loaded zeolites. Although wet scrubbing can effectively remove iodine, it suffers from corrosion of the vessel due to high concentration of the scrubbing solution. Silver loaded zeolites also show effectiveness in capturing {sup 129}I gas, yet weak thermal stability of physisorbed iodine remains a challenge. We studied a novel and facile method to trap iodine gas using bismuth. Granular bismuth having many pores was synthesized using bismuth nitrate and polyvinyl alcohol as a bismuth precursor and pore forming agent, respectively. Reaction of iodine and our samples resulted in an iodine capturing capacity of more than 2 times that of the commercial grade silver exchanged zeolite (AgX). Granular porous bismuths synthesized using bismuth nitrate and PVA show a promising performance in capturing iodine gas. The use of bismuth in trapping {sup 129}I gas can reduce the process cost as bismuth is cheap. Further study is going on to improve the mechanical property of granular porous bismuths for their easy handling.

  4. Iodine Gas Trapping using Granular Porous Bismuth

    International Nuclear Information System (INIS)

    Yang, Jae Hwan; Shin, Jin Myeong; Park, Jang Jin; Park, Geun Il; Yim, Mansung

    2014-01-01

    129 I is a radionuclide with a very long half-life of 1.57 Χ 10 7 years and has negative health effects to the human body. Therefore, the emission of 129 I into the air is closely regulated by the Environmental Protection Agency (EPA). Many methods for trapping gaseous 129 I have been developed thus far, including wet scrubbing and adsorption using silver loaded zeolites. Although wet scrubbing can effectively remove iodine, it suffers from corrosion of the vessel due to high concentration of the scrubbing solution. Silver loaded zeolites also show effectiveness in capturing 129 I gas, yet weak thermal stability of physisorbed iodine remains a challenge. We studied a novel and facile method to trap iodine gas using bismuth. Granular bismuth having many pores was synthesized using bismuth nitrate and polyvinyl alcohol as a bismuth precursor and pore forming agent, respectively. Reaction of iodine and our samples resulted in an iodine capturing capacity of more than 2 times that of the commercial grade silver exchanged zeolite (AgX). Granular porous bismuths synthesized using bismuth nitrate and PVA show a promising performance in capturing iodine gas. The use of bismuth in trapping 129 I gas can reduce the process cost as bismuth is cheap. Further study is going on to improve the mechanical property of granular porous bismuths for their easy handling

  5. Oxygen depletion of bismuth molybdates

    Energy Technology Data Exchange (ETDEWEB)

    Yong, L.K.; Howe, R.F.; Keulks, G.W.; Hall, W.K.

    1978-05-01

    Pure ..cap alpha..-phase bismuth molybdate (Bi/sub 2/Mo/sub 3/O/sub 12/), which is known to be weakly active for selective oxidation, and pure ..gamma..-phase bismuth molybdate (Bi/sub 2/MoO/sub 6/), which has good activity, were subjected to oxidation-reduction cycles with known amounts of hydrogen and oxygen, at 300/sup 0/-570/sup 0/C and with evacuation steps between treatments. The volume of oxygen consumed during reoxidation was equal to half the hydrogen consumed during the reduction on the ..cap alpha..-phase, which indicated that no hydrogen was retained during reduction. For the ..gamma..-phase, the oxygen consumption was greater than half of the hydrogen consumption and it increased with extent of reduction. The excess oxygen was apparently consumed by filling anion vacancies formed during outgassing subsequent to the reduction step. ESR spectroscopy and temperature-programed oxidation-reduction indicated that lattice oxide ions which bridge between bismuth and molybdenum layers of the koechlinite structure become more labile when the catalyst is in a partially reduced state, and that this effect is greater in the ..gamma..- than the ..cap alpha..-phase. Table and 15 references.

  6. Bismuth absorption from sup 205 Bi-labelled pharmaceutical bismuth compounds used in the treatment of peptic ulcer disease

    Energy Technology Data Exchange (ETDEWEB)

    Dresow, B.; Fischer, R.; Gabbe, E.E.; Wendel, J.; Heinrich, H.C. (Eppendorf University Hospital, Hamburg (Germany))

    1992-04-01

    The absorption of bismuth from five {sup 205}Bi-labelled pharmaceutically used bismuth compounds was studied in man. From single oral doses of all compounds under investigation only <0.1% bismuth was absorbed and excreted with the urine. A significantly higher absorption was observed from the colloidal bismuth subcitrate and the basic bismuth gallate than from the basic bismuth salicylate, nitrate and aluminate. No retention of bismuth in the whole body was found from the single dose experiment. The biologic fast-term half-lives of absorbed bismuth were calculated to be 0.12 and 1.5 days. 14 refs., 2 figs., 1 tab.

  7. Levels of lead-210 (210Pb) and polonium 210 (210Po) in Cuban Tobacco products

    International Nuclear Information System (INIS)

    Brigido, F.O.; Barrerras Caballero, A.; Alvarez Rodriguez, D.; Montalvan Estrada, A.

    1999-01-01

    The release of 210Po in tobacco smoke and the radiation dose for man have been studied because of the high incidence of lung cancer among smoker. The electroplating of polonium at two different times onto copper disks and further measurement of alpha activity was the meted used for 210 Po determination in tobacco products. The Polonium daughter is used to determine both the 210Pb and 210Po using the Baseman equations for radioactive growth and decay. A cigarette contains between 10.6 and 14.7 mBq of 210Pb with an average activity of 13.0 mBq and between 8.5 and 12.3 mBq of 210Po with an average activity of 10.4 mBq for different Cuban cigarette brands. For a person smoking a pack of 20 cigarettes a day, the values of intakes estimated range from 32 to 44 mBq for 210Pb and from 34 to 49 mBq for 210 Po with an average daily intake of 39 mBq for 210 Pb and 42 mBq for 210Po. The annual effective dose estimated due to inhalation of these nuclides contained in cigarette smoke shows a value of 66[Sv and was in correspondence with world-wide range dose, 46 - 90 mSv.year 1 - for tobacco product consumption

  8. Dietary intake of barium, bismuth, chromium, lithium, and strontium in a Spanish population (Canary Islands, Spain).

    Science.gov (United States)

    González-Weller, Dailos; Rubio, Carmen; Gutiérrez, Ángel José; González, Gara Luis; Caballero Mesa, José María; Revert Gironés, Consuelo; Burgos Ojeda, Antonio; Hardisson, Arturo

    2013-12-01

    The aim of this study was to analyze barium, bismuth, chromium, lithium, and strontium contents in food and beverages consumed by the population of the Canary Islands (Spain) as well as determine dietary intake of these metals in the archipelago as a whole and in its individual islands. To this end, 440 samples were analyzed by ICP-OES and GFAAS. Barium concentrations ranged from 5.210 ± 2.117 mg/kg in nuts to 0.035 ± 0.043 mg/L in water. Viscera exhibited the highest levels of bismuth (38.07 ± 36.80 mg/kg). The cold meat and sausages group stood out for its high chromium concentrations (0.494 ± 0.257 mg/kg). The highest concentration of lithium and strontium came out in nuts (8.761 ± 5.368 mg/kg and 9.759 ± 5.181 mg/kg, respectively). The total intakes of barium, bismuth, chromium, lithium, and strontium were 0.685, 1.274, 0.087, 3.674, and 1.923 mg/day, respectively. Cereals turned out to contribute most to the dietary intake of barium, bismuth, chromium, and lithium in the Canary Islands, while fruit contributes most to the strontium intake. We also performed a metal intake study by age and sex of the population and compared the outcome with data from other regions, both national and international.

  9. Bismuth ions are metabolized into autometallographic traceable bismuth-sulphur quantum dots

    Directory of Open Access Journals (Sweden)

    M Stoltenberg

    2009-06-01

    Full Text Available Bismuth – sulphur quantum dots can be silver enhanced by autometallography (AMG. In the present study, autometallographic silver enhanced bismuth-sulphur nanocrystals were isolated from unfixed cryo-sections of kidneys and livers of rats exposed to bismuth (Bi207 subnitrate. After being subjected to AMG all the organic material was removed by sonication and enzymatic digestion and the silver enhanced Bi- S quantum dots spun down by an ultracentrifuge and analyzed by scintillation. The analysis showed that the autometallographic technique traces approximately 94% of the total bismuth. This implies that the injected bismuth is ultimately captured in bismuthsulphur quantum dots, i.e., that Bi-S nanocrystals are the end product of bismuth metabolism

  10. Levels of 210 Pb and 210 Po in Brazilian cigarettes

    International Nuclear Information System (INIS)

    Santos, Pedro Lopes dos; Kelecom, Alphonse; Gouvea, Rita de Cassia dos Santos; Dutra, Iedo Ramos

    1996-01-01

    210 Po and 210 Pb concentrations have been determined in 18 Brazilian cigarette samples and compared with known data on U content. U is respectively 3-fold less and 4-fold less abundant than 210 Po or 210 Pb. No correlation could be observed between U concentration and those of Po or Pb. The mean concentration of 210 Pb is higher than that of 210 Pb observed in many other plants, even in plants frown in high background areas. (author)

  11. Natural levels of lead-210, polonium-210 and radium-226 in humans and biota of the Arctic

    Energy Technology Data Exchange (ETDEWEB)

    Holtzman, R B

    1966-06-11

    Relatively high concentrations of some fission products in humans and biota from Lapland and Alaska have been reported. These have been attributed to the continual accumulation of those products on the long-lived, slow-growing Arctic lichens and sedges. Such plants are an important source of forage for reindeer and caribou, the meat of which, in turn, constitutes a substantial portion of the diets of Laplanders and Eskimos. These high levels of fall-out suggest, together with the proposed mechanism of uptake and the similarities to strontium-90 in atmospheric distribution and biochemistry, that in Arctic biota, the naturally occurring airborne nuclides lead-210 and its decay product, polonium-210, may also be present in high concentration. These naturally occurring fall-out activities are of special interest in studies of aerosol precipitation mechanisms because their levels are independent of bomb tests and consequently they have been constant over the years. Because of this constancy and the high energy of the particles emitted by the lead-210 series (a 5.3-MeV ..cap alpha..-particle from polonium-210 and a 0.4-MeV (average energy) ..beta..-particle from bismuth-210 compared with ..beta..-rays with average energies of 0.4 MeV from cesium-137 and 1.1 MeV from strontium-90 (yttrium-90)), the radiation dose to Arctic biota from this source may be quite significant relative to that from artificial ones. 24 references.

  12. Contribution to the study of the geophysical behaviour of lead-210 by application of alpha spectrometry

    International Nuclear Information System (INIS)

    Nezami, M.

    1965-06-01

    A study of the changes in the lead-210 contents of rain-water and of water produced by melting polar ice has required the development of a method for dosing lead-210, an α emitter. This method is 40 times more sensitive than that which measures the lead-210 by bismuth-210, a (β emitter. The first part of the report presents the study of a spectrometry using semiconductor detectors; a catalogue of a spectra shows the advantages of this method. In the second part will be found at first a new chemical separation method for polonium-210 and the results obtained with this method. The main results obtained on the geophysical behaviour of lead-210 are the following: - the monthly lead-210 and polonium-210 contents in rain water are approximately constant with time. - in the Gif-sur-Yvette region, the clean-up by 'dry fall-out' can attain 40 to 50 per cent of the total fall-out. - a study of Antarctic ice samples makes it possible to determine an annual accumulation rate equivalent to 13.8 cm of water and to show discrepancies in the periodic concentrations which correspond to the latest maxima of solar activity. - a balance is drawn up between the radon produced by the continents and the lead-210 fall-out. (author) [fr

  13. Reactive magnetron sputtering deposition of bismuth tungstate onto titania nanoparticles for enhancing visible light photocatalytic activity

    Energy Technology Data Exchange (ETDEWEB)

    Ratova, Marina, E-mail: marina_ratova@hotmail.com [Surface Engineering Group, School of Engineering, Manchester Metropolitan University, Manchester, M1 5GD (United Kingdom); Kelly, Peter J.; West, Glen T. [Surface Engineering Group, School of Engineering, Manchester Metropolitan University, Manchester, M1 5GD (United Kingdom); Tosheva, Lubomira; Edge, Michele [School of Science and the Environment, Manchester Metropolitan University, Manchester M1 5GD (United Kingdom)

    2017-01-15

    Highlights: • Bismuth tungstate coatings were deposited by reactive magnetron sputtering. • Oscillating bowl was introduced to the system to enable coating of nanopartulates. • Deposition of Bi{sub 2}WO{sub 6} enhanced visible light activity of titania nanoparticles. • The best results were obtained for coating with Bi:W ratio of approximately 2:1. • Deposition of Bi{sub 2}WO{sub 6} onto TiO{sub 2} resulted in more efficient electron-hole separation. - Abstract: Titanium dioxide − bismuth tungstate composite materials were prepared by pulsed DC reactive magnetron sputtering of bismuth and tungsten metallic targets in argon/oxygen atmosphere onto anatase and rutile titania nanoparticles. The use of an oscillating bowl placed beneath the two magnetrons arranged in a co-planar closed field configuration enabled the deposition of bismuth tungstate onto loose powders, rather than a solid substrate. The atomic ratio of the bismuth/tungsten coatings was controlled by varying the power applied to each target. The effect of the bismuth tungstate coatings on the phase, optical and photocatalytic properties of titania was investigated by X-ray diffraction, energy-dispersive X-ray spectroscopy (EDX), Brunauer–Emmett–Teller (BET) surface area measurements, transmission electron microscopy (TEM), UV–vis diffuse reflectance spectroscopy and an acetone degradation test. The latter involved measurements of the rate of CO{sub 2} evolution under visible light irradiation of the photocatalysts, which indicated that the deposition of bismuth tungstate resulted in a significant enhancement of visible light activity, for both anatase and rutile titania particles. The best results were achieved for coatings with a bismuth to tungsten atomic ratio of 2:1. In addition, the mechanism by which the photocatalytic activity of the TiO{sub 2} nanoparticles was enhanced by compounding it with bismuth tungstate was studied by microwave cavity perturbation. The results of these

  14. Neutron scattering differential cross sections of carbon and bismuth at 37 MeV

    International Nuclear Information System (INIS)

    Zhou Zuying; Tang Hongqing; Qi Bujia; Zhou Chenwei; Du Yanfeng; Xia Haihong; Walter, R.L.; Tornow, W.; Howell, C.; Braun, R.; Roper, C.; Chen Zemin; Chen Zhengpeng; Chen Yingtang

    1997-01-01

    Elastic differential cross sections of 37 MeV neutrons scattered from carbon and bismuth were measured in the angular range 11 to 160 degrees by means of the multi-detector TOF facility. The 37 MeV neutrons were produced via the T(d,n) 4 He reaction in a tritium gas target. The pulsed 20 MeV deuteron beam was provided by the HI-13 tandem accelerator. The angular distribution of scattered neutrons from carbon and bismuth were measured in the angular range 11 degree to 145 degree and 11 degree to 160 degree respectively in steps of about 3 degree

  15. Study of inclusive proton spectra from 20 MeV deuteron breakup by bismuth

    International Nuclear Information System (INIS)

    Badiger, N.M.; Hallur, B.R.; Madhusoodhanan, T.; Sathyavathiamma, M.P.; Puttaswamy, N.G.; Darshan, V.P.; Sharma, H.; Chintalapudi, S.N.

    1997-01-01

    The breakup of deuteron into proton and neutron has been studied earlier to understand the breakup mechanism. Inclusive measurements show the expected broad bumps near the beam velocity. In the present experiment, the breakup of 20 MeV deuterons by bismuth target has been investigated

  16. Gravimetric Analysis of Bismuth in Bismuth Subsalicylate Tablets: A Versatile Quantitative Experiment for Undergraduate Laboratories

    Science.gov (United States)

    Davis, Eric; Cheung, Ken; Pauls, Steve; Dick, Jonathan; Roth, Elijah; Zalewski, Nicole; Veldhuizen, Christopher; Coeler, Joel

    2015-01-01

    In this laboratory experiment, lower- and upper-division students dissolved bismuth subsalicylate tablets in acid and precipitated the resultant Bi[superscript 3+] in solution with sodium phosphate for a gravimetric determination of bismuth subsalicylate in the tablets. With a labeled concentration of 262 mg/tablet, the combined data from three…

  17. Levels of 210Po and 210Pb in cigars

    International Nuclear Information System (INIS)

    Kelecom, A.; Gouvea, R.C.S.; Santos, P.L.

    2002-01-01

    210 Po and 210 Pb concentrations have been determined in 58 cigar brands manufactured in 11 countries. Cuban and American cigars showed the lowest 210 Po content. The mean levels of 210 Po in Brazilian, European and Dominican cigars were almost identical and somewhat lower than the levels observed for cigars from other Latin American countries. Cuban, American and European cigars contained low levels of 210 Pb. Cigars from the remaining countries contained twice as much 210 Pb. The mean 210 Po/ 210 Pb ratio showed an excess of polonium. In the case of one cigar-a-day smoker, the calculated annual absorbed dose due to 210 Po is ∼16 μGy. (author)

  18. Concentration of Po-210 and Pb-210 in human tissues

    International Nuclear Information System (INIS)

    Zhao Lancai; Takizawa, Y.; Yamamoto, M.

    1990-01-01

    The levels of Pb-210 and Po-210 in human tissues of people in Japan were determined. Various tissue samples were obtained at autopsy from the cadavers of 22 oncologic cases, mainly in Niigata Prefecture in northern Japan during the period of 1986 to 1988. Wet ashing, followed by electrochemical deposition and alpha-ray spectrometry were used to separate and determine the Pb-210 and Po-210 presented. Among the tissues analyzed the highest concentrations of Pb-210 and Po-210 were observed in bone, liver and kidneys: 1.29, 1.69 and 1.22 Bq.kg -1 respectively for Po-210, and 1.27, 0.56 and 0.43 Bq/kg for Pb-210 respectively. The Po-210/Pb-210 ratios in liver and kidney are 3.0 and 2.9 respectively. Po-210/Pb-210 ratios in other tissues are close to one. The total body burden of Pb-210 and Po-210 was found to be approximately 15.8 Bq and 19.1 Bq respectively

  19. Short report: evaluation of Helicobacter pylori eradication with bismuth sucralfate

    NARCIS (Netherlands)

    Reijers, M. H.; Noach, L. A.; Tytgat, G. N.

    1994-01-01

    In a pilot study we have evaluated the clinical efficacy of bismuth sucralfate to eradicate H. pylori. Ten consecutive patients with chronic dyspepsia and H. pylori associated gastritis were treated with bismuth sucralfate (220 mg bismuth per tablet, 4 tablets per day for 4 weeks). If a 14C urea

  20. Environmental radioactivity of radon daughter's radionuclides 210Pb-210Bi-210Po

    International Nuclear Information System (INIS)

    Momoshima, N.

    2003-01-01

    Radionuclide, 210 Pb(22.3 y)- 210 Bi(5.013 d)- 210 Po(138.4 d) belongs to the uranium decay chain and widely distributed in the environment. 222 Rn escaped from the earth surface is a major source of atmospheric 210 Pb. These nuclides attach with atmospheric aerosols and are removed to the ground as wet and dry depositions. The residence time of the atmospheric aerosol, thus, was obtained by activity ratios of 210 Bi/ 210 Pb and 210 Po/ 210 Pb, showing different values. The discrepancy on the residence times are explained with inputs of 210 Po to the atmosphere other than 222 Rn emanated from the earth surface. The removal of aerosol as wet deposition occupies a significant fraction, which reaches 72% on 210 Pb and 89% on 7 Be. In the ocean, the radionuclides are used as tracer to examine dynamic processes occurring in the ocean, such as removal of particulate matter from seawater column to bottom. The 210 Pb and 210 Po concentrations in the ocean water collected off continent decreased from surface toward bottom, and the shortage on 210 Po content relative to that of 210 Po was observed at shallow ocean layers, however, the 210 Po/ 210 Pb activity ratio closed to the radioactive equilibrium at deeper layers. The 210 Pb is a very good tracer to evaluate an accumulation rate of bottom sediment in ocean, lake and river. This is called as 210 Pb dating and is successfully applicable to accumulation circumstances that bottom sediment deposits at constant rate. Most of the actual cases, simultaneous 137 Cs dating is carried out, which uses 137 Cs peak in the core as originated from radioactive fallout of nuclear tests, showing the maximum in 1963. Recently new findings on source of atmospheric 210 Po are report by laboratory experiments and environmental measurements, which proves biologically supported emission of volatile Po compounds to the atmosphere. (author)

  1. Bismuth titanate nanorods and their visible light photocatalytic properties

    International Nuclear Information System (INIS)

    Pei, L.Z.; Liu, H.D.; Lin, N.; Yu, H.Y.

    2015-01-01

    Highlights: • Bismuth titanate nanorods have been synthesized by a simple hydrothermal process. • The size of bismuth titanate nanorods can be controlled by growth conditions. • Bismuth titanate nanorods show good photocatalytic activities of methylene blue and Rhodamine B. - Abstract: Bismuth titanate nanorods have been prepared using a facile hydrothermal process without additives. The bismuth titanate products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM) and UV-vis diffusion reflectance spectrum. XRD pattern shows that the bismuth titanate nanorods are composed of cubic Bi 2 Ti 2 O 7 phase. Electron microscopy images show that the length and diameter of the bismuth titanate nanorods are 50-200 nm and 2 μm, respectively. Hydrothermal temperature and reaction time play important roles on the formation and size of the bismuth titanate nanorods. UV-vis diffusion reflectance spectrum indicates that bismuth titanate nanorods have a band gap of 2.58 eV. The bismuth titanate nanorods exhibit good photocatalytic activities in the photocatalytic degradation of methylene blue (MB) and Rhodamine B (RB) under visible light irradiation. The bismuth titanate nanorods with cubic Bi 2 Ti 2 O 7 phase are a promising candidate as a visible light photocatalyst

  2. Bismuth Subgallate Toxicity in the Age of Online Supplement Use.

    Science.gov (United States)

    Sampognaro, Paul; Vo, Kathy T; Richie, Megan; Blanc, Paul D; Keenan, Kevin

    2017-11-01

    Bismuth salts have been used to treat gastroenterological disorders and are readily available over-the-counter and via the internet. Even though generally considered safe, bismuth compounds can cause a syndrome of subacute, progressive encephalopathy when taken in large quantities. We present the case of woman who developed progressive encephalopathy, aphasia, myoclonus, and gait instability after chronically ingesting large amounts of bismuth subgallate purchased from a major online marketing website to control symptoms of irritable bowel syndrome. After extensive neurological work-up, elevated bismuth levels in her blood, urine, and cerebrospinal fluid confirmed the diagnosis of bismuth-related neurotoxicity. She improved slowly following cessation of exposure. This case highlights bismuth subgallate as a neurotoxic bismuth formulation and reminds providers of the potential for safety misconceptions of positively reviewed online supplements.

  3. Investigation of corrosion, water reaction, polonium evaporation and bismuth resource in liquid metal lead-bismuth technology

    Energy Technology Data Exchange (ETDEWEB)

    Takano, Hideki; Takizuka, Takakazu [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kitano, Teruaki [Mitsui Shipbuilding and Engineering Co. Ltd., Tokyo (Japan)

    2000-10-01

    Lead-bismuth is the first candidate material for liquid metal target find coolant of fueled blanket system in accelerator-driven system (ADS) studied at JAERI. Advantages of the lead-bismuth utilization are non-active material, very low capture cross section, low melting point of 125degC and high boiling point of 1670degC, and beside coolant void reactivity become negative. But problems are due to the high corrosivity to most of the structural materials and the corrosive data are scarcity. In this report, corrosivity, reaction with water, thermal-hydraulics, chemical toxicity etc. are studied by investigating some facilities utilized and researched really for lead or lead-bismuth. And, furthermore, polonium evaporation rate and bismuth resource are investigated. Main results obtained are as follows: (1) In a refinery, there are enough employment experience for liquid Pb-Bi in period of about 17 years and not corrosion for the thermal conductive materials (1Cr-0.5Mo steel) used under the condition of natural convection with temperature around 400degC. (2) In Russia, extensive experience in the use as Russian submarines and in R and D during about 50 years are available. And as a result, it will be able to lead approximately zero corrosion for Cr-Si materials by adjusting oxygen film with oxygen concentration control between 10{sup -7} to 10{sup -5}% mass. However, the corrosion data are not enough systematically collected involving them in radiation dose field. (3) In liquid-dropping experiment, it is shown that interaction between water and high temperature liquid Pb-Bi is reduced steeply with rising of atmosphere pressure. But, in order to design the second circuit removal model of ADS, the interaction should be evaluated by water continuous injection experiment. (4) Polonium forms PbPo in Pb-Bi, and the evaporation rate become less three factor than that of Po, and furthermore, the rate decreases in the atmosphere. The effects of Po on employee and environment

  4. Radio-sensitization of animals by bismuth; Radio sensibilisation de l'animal par le bismuth

    Energy Technology Data Exchange (ETDEWEB)

    Pierotti, T; Verain, A [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1969-07-01

    Digestive absorption of bismuth by animals leads to radio-sensitization. This effect is very marked when the X-rays used are centered on the absorption line of bismuth. This work has involved the use of more than 2000 C3H/JAX mice, and has shown that a maximum lethal effect, with respect to the standard, occurs for bismuth sub-nitrate doses of the order of 3 g/kg and for exposures of 700 R. For stronger or weaker doses, the sensitization effect is less marked. (authors) [French] L'absorption digestive de bismuth provoque une radiosensibilisation de l'animal. Celle-ci est nette quand le rayonnement X utilise est centre sur la raie d'absorption du bismuth. L'etude portant sur plus de 2000 souris C3H/JAX a montre une lethalite maximale par rapport aux temoins pour des doses de sous-nitrate de bismuth de l'ordre de 3 g/kg et pour des expositions de 700 R. Pour des doses plus fortes ou plus faibles, l'effet de sensibilisation est moins net. (auteurs)

  5. Evaluation on the characteristics of tin-silver-bismuth solder

    Science.gov (United States)

    Xia, Z.; Shi, Y.; Chen, Z.

    2002-02-01

    Tin-silver-bismuth solder is characterized by its lower melting point, good wetting behavior, and good mechanical property for which it is expected to be a new lead-free solder to replace tin-lead solder. In this article, Sn-3.33Ag-4.83Bi solder was investigated concerning its physical, spreading, and mechanical properties under specific conditions. Cooling curves and DSC results showed that it was close to eutectic composition (m.p. 210° 212 °C). Coefficiency of thermal expansion (CTE) of this solder, between that of PCBs and copper substrates, was beneficial to alleviate the thermal mismatch of the substrates. It was also a good electrical and thermal conductor. Using a rosin-based, mildly activated (RMA) flux, a spreading test indicated that SnAgBi solder paste had good solderability. Meanwhile, the solder had high tensile strength and fracture energy. Its fracture mechanism was a mixture of ductile and brittle fracture morphology. The metallographic and EDAX analyses indicated that it was composed of a tin-based solid solution and some intermetallic compound (IMC) that could strengthen the substrate. However, these large needle-like IMCs would cut the substrate and this resulted in the decreasing of the toughness of the solder.

  6. 21 CFR 73.2110 - Bismuth citrate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Bismuth citrate. 73.2110 Section 73.2110 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL LISTING OF COLOR... paragraph (c)(1), effective April 27, 2010. For the convenience of the user, the revised text is set forth...

  7. Magnetoreflection studies of ion implanted bismuth

    International Nuclear Information System (INIS)

    Nicolini, C.; Chieu, T.C.; Dresselhaus, M.S.; Massachusetts Inst. of Tech., Cambridge; Dresselhaus, G.

    1982-01-01

    The effect of the implantation of Sb ions on the electronic structure of the semimetal bismuth is studied by the magnetoreflection technique. The results show long electronic mean free paths and large implantation-induced increases in the band overlap and L-point band gap. These effects are opposite to those observed for Bi chemically doped with Sb. (author)

  8. Branching ratio to the 803 keV level in 210Poα decay

    Science.gov (United States)

    Shor, A.; Weissman, L.; Aviv, O.; Eisen, Y.; Brandis, M.; Paul, M.; Plompen, A.; Tessler, M.; Vaintraub, S.

    2018-03-01

    Precise knowledge of the branching ratio in the α decay of 210Po is important for accurate measurement of the 209Bi(n ,γ )Big210 cross section, the reaction involved in the termination of the astrophysical s process. The branching ratio was determined from independent measurements of α and γ spectra of bismuth samples simultaneously irradiated by neutrons near the core of the Soreq research reactor (IRR1). The branching ratio was found to be (1.15 ±0.09 ) ×10-5 , consistent with the results of several measurements performed six decades ago. As a by-product value the 209Bi(n ,γ )Big210 thermal cross section was measured to be 21.6 ±1.1 mb.

  9. Environmental Assessment for Increased Depleted Uranium Use on Target 63-10, Nevada Test and Training Range

    Science.gov (United States)

    2006-09-01

    min. β Bismuth-214 19.9 min. β Polonium -214 1.5 x 10-4 sec. α Lead- 210 22 years β Bismuth- 210 5 days β Polonium - 210 140 days α Lead-206 stable...Uranium-234 2.5 x 105 years α Thorium-230 7.7 x 104 years α Radium-226 1600 years α Radon-222 3.8235 days α Polonium -218 3.05 min. α Lead-214 26.8...the degraded areas where ordnance delivery occurs. This also applies to DU use. These areas do not provide food or habitat resources likely to

  10. Selective resputtering of bismuth in sputtered Bi-Sr-Ca-Cu-O films

    Science.gov (United States)

    Grace, J. M.; McDonald, D. B.; Reiten, M. T.; Olson, J.; Kampwirth, R. T.; Gray, K. E.

    1991-10-01

    We present studies using a dc magnetron in an on-axis configuration to sputter Bi-Sr-Ca-Cu-O films from a composite target. These studies show that bismuth can be preferentially resputtered. The influence of ozone, molecular oxygen, and total pressure on the resputtering of bismuth is investigated and discussed. Ozone, in low concentrations, can dramatically affect the degree of resputtering. By comparing the effects of molecular oxygen and ozone, some insight is gained regarding the possible mechanisms of negative ion formation in the magnetron environment. Based on our results we suggest that molecular oxygen can bring about resputtering primarily by forming O+2, which collides with the target to produce energetic negative oxygen ions. In contrast, ozone may form negative ions by electron impact in the dark space above the target, giving rise to lower-energy negative ions, which can traverse the plasma unneutralized and can be stopped with an applied bias on the sample block. With no added oxidant, negative oxygen ions from the target oxygen may dominate the background resputtering. Similarity is found between our results and those for similar studies on Y-Ba-Cu-O by other workers. Bismuth in Bi-Sr-Ca-Cu-O behaves as barium in Y-Ba-Cu-O with regards to preferential resputtering; furthermore, the response of strontium, calcium, and copper to oxygen in sputtered Bi-Sr-Ca-Cu-O is similar to what is observed for copper in Y-Ba-Cu-O.

  11. Selective resputtering of bismuth in sputtered Bi-Sr-Ca-Cu-O films

    International Nuclear Information System (INIS)

    Grace, J.M.; McDonald, D.B.; Reiten, M.T.; Olson, J.; Kampwirth, R.T.; Gray, K.E.

    1991-01-01

    We present studies using a dc magnetron in an on-axis configuration to sputter Bi-Sr-Ca-Cu-O films from a composite target. These studies show that bismuth can be preferentially resputtered. The influence of ozone, molecular oxygen, and total pressure on the resputtering of bismuth is investigated and discussed. Ozone, in low concentrations, can dramatically affect the degree of resputtering. By comparing the effects of molecular oxygen and ozone, some insight is gained regarding the possible mechanisms of negative ion formation in the magnetron environment. Based on our results we suggest that molecular oxygen can bring about resputtering primarily by forming O + 2 , which collides with the target to produce energetic negative oxygen ions. In contrast, ozone may form negative ions by electron impact in the dark space above the target, giving rise to lower-energy negative ions, which can traverse the plasma unneutralized and can be stopped with an applied bias on the sample block. With no added oxidant, negative oxygen ions from the target oxygen may dominate the background resputtering. Similarity is found between our results and those for similar studies on Y-Ba-Cu-O by other workers. Bismuth in Bi-Sr-Ca-Cu-O behaves as barium in Y-Ba-Cu-O with regards to preferential resputtering; furthermore, the response of strontium, calcium, and copper to oxygen in sputtered Bi-Sr-Ca-Cu-O is similar to what is observed for copper in Y-Ba-Cu-O

  12. Monte Carlo simulations for dose enhancement in cancer treatment using bismuth oxide nanoparticles implanted in brain soft tissue.

    Science.gov (United States)

    Taha, Eslam; Djouider, Fathi; Banoqitah, Essam

    2018-03-26

    The objective of this work is to study the dosimetric performances of bismuth oxide nanoparticles implanted in tumors in cancer radiotherapy. GEANT4 based Monte Carlo numerical simulations were performed to assess dose enhancement distributions in and around a 1 × 1 × 1 cm 3 tumor implanted with different concentrations of bismuth oxide and irradiated with low energies 125 I, 131 Cs, and 103 Pd radioactive sources. Dose contributions were considered from photoelectrons, Auger electrons, and characteristic X-rays. Our results show the dose enhancement increased with increasing both bismuth oxide concentration in the target and photon energy. A dose enhancement factor up to 18.55 was obtained for a concentration of 70 mg/g of bismuth oxide in the tumor when irradiated with 131 Cs source. This study showed that bismuth oxide nanoparticles are innovative agents that could be potentially applicable to in vivo cancer radiotherapy due to the fact that they induce a highly localized energy deposition within the tumor.

  13. 210Pb and 210Po in Finnish cereals

    International Nuclear Information System (INIS)

    Turtiainen, Tuukka; Kostiainen, Eila; Hallikainen, Anja

    2011-01-01

    A survey was carried out on the activity concentrations of 210 Pb and 210 Po in cereal grains produced in Finland. The cereal species were wheat (Triticum aestivum), rye (Secale cereale), oats (Avena sativa) and barley (Hordeum vulgare), which account for 90% of the Finnish consumption of cereal products. The survey consisted of 18 flour and 13 unprocessed cereal samples and one hulled grain sample from 22 flour mills. According to the results, the mean 210 Pb/ 210 Po concentrations in wheat grains, wheat flour, rye flour, oat grains and barley grains were 0.29, 0.12, 0.29, 0.36 and 0.36 Bq kg -1 , respectively. Combined with the consumption rates of the products, we assess that the mean effective doses from 210 Pb and 210 Po in cereal products for the adult male and female population are 22 and 17 μSv per year, respectively.

  14. Study on the excretion of pb-210 and po-210

    Energy Technology Data Exchange (ETDEWEB)

    Okabayashi, Hiroyuki [National Inst. of Radiological Sciences, Chiba (Japan)

    1982-06-01

    The amount of Po-210 excreted in urine and feces was more influenced by Po-210 that was taken with food and drink than taken through inhalation. The amount of Pb-210 in urine of mining workers among uranium mine workers was higher than that of the non-uranium mine workers. It was thought that this fact was due to the working environment in uranium mine the amount of Pb-210 being a few tens times higher than that in normal environment. The activity ratios of Po-210 of faecal to urinary excretion are widely distributed, however, the average value of many samples approached to 10. Urinary excretion of Po-210 was highest after 24 hours of ingestion, but for faecal excretion, it was highest after 3 day.

  15. 210Pb and 210Po in Finnish cereals.

    Science.gov (United States)

    Turtiainen, Tuukka; Kostiainen, Eila; Hallikainen, Anja

    2011-05-01

    A survey was carried out on the activity concentrations of (210)Pb and (210)Po in cereal grains produced in Finland. The cereal species were wheat (Triticum aestivum), rye (Secale cereale), oats (Avena sativa) and barley (Hordeum vulgare), which account for 90% of the Finnish consumption of cereal products. The survey consisted of 18 flour and 13 unprocessed cereal samples and one hulled grain sample from 22 flour mills. According to the results, the mean (210)Pb/(210)Po concentrations in wheat grains, wheat flour, rye flour, oat grains and barley grains were 0.29, 0.12, 0.29, 0.36 and 0.36 Bq kg(-1), respectively. Combined with the consumption rates of the products, we assess that the mean effective doses from (210)Pb and (210)Po in cereal products for the adult male and female population are 22 and 17 μSv per year, respectively. Copyright © 2010 Elsevier Ltd. All rights reserved.

  16. Bismuth( Ⅲ ) Salts: Green Catalysts for Organic Transformations

    Institute of Scientific and Technical Information of China (English)

    C. Le Roux

    2005-01-01

    @@ 1Introduction Bismuth, the heaviest stable element in the periodic table, stands out from other heavy elements (such as mercury, thallium and lead) due to its relatively non-toxic character which confers on bismuth the enviable status of being an eco-friendly element. Therefore, bismuth and its compounds hold considerable promise as useful catalysts for green chemistry. The research presented in this communication is devoted to the applications of bismuth( Ⅲ ) salts as catalysts for organic transformations.After some general comments about bismuth and a short presentation of the various applications of bismuth( Ⅲ ) salts in organic synthesis, this communication will focus on the works done in our research group during the last several years which deals mainly with electrophilic substitutions. When appropriate, some mechanistic details will be given.

  17. Coolant Chemistry Control: Oxygen Mass Transport in Lead Bismuth Eutectic

    International Nuclear Information System (INIS)

    Weisenburger, A.; Mueller, G.; Bruzzese, C.; Glass, A.

    2015-01-01

    In lead-bismuth cooled transmutation systems, oxygen, dissolved in the coolant at defined quantities, is required for stable long-term operation by assuring the formation of protective oxide scales on structural steel surfaces. Extracted oxygen must be permanently delivered to the system and distributed in the entire core. Therefore, coolant chemistry control involves detailed knowledge on oxygen mass transport. Beside the different flow regimes a core might have stagnant areas at which oxygen delivery can only be realised by diffusion. The difference between oxygen transport in flow paths and in stagnant zones is one of the targets of such experiments. To investigate oxygen mass transport in flowing and stagnant conditions, a dedicated facility was designed based on computational fluid dynamics (CFD). CFD also was applied to define the position of oxygen sensors and ultrasonic Doppler velocimetry transducers for flow measurements. This contribution will present the test facility, design relevant CFD calculations and results of first tests performed. (authors)

  18. Thermal decomposition synthesis of nanorods bismuth sulphide from bismuth N-ethyl cyclohexyl dithiocarbamate complex

    International Nuclear Information System (INIS)

    Abdullah, Nurul Hidayah; Zainal, Zulkarnain; Silong, Sidik; Tahir, Mohamed Ibrahim Mohamed; Tan, Kar-Ban; Chang, Sook-Keng

    2016-01-01

    Highlights: • Bismuth N-ethyl cyclohexyl dithiocarbamate was used as single source precursor. • No surfactant was used in the preparation of Bi_2S_3 nanorods. • Pure phase orthorhombic Bi_2S_3 is obtained. • Bismuth sulphide with an average atomic ratio of Bi:S close to 2:3 is obtained. - Abstract: Nanorods of bismuth sulphide were prepared by thermal decomposition of bismuth N-ethyl cyclohexyl dithiocarbamate at different calcination duration. X-ray diffraction (XRD) analysis shows that at 400 °C, the precursor was fully decomposed to orthorhombic bismuth sulphide after 2 h of calcination. Besides, calcination duration does not affect the existence of Bi_2S_3 phase. Field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) analyses reveal that Bi_2S_3 nanorods with an average width ranging from 29–36 nm were obtained. Energy dispersive X-ray (EDX) analysis confirmed the atomic ratio of Bi and S close to 2:3, giving a possible composition of Bi_2S_3. Direct band gap energy of Bi_2S_3 decreases from 1.83 eV to 1.54 eV as calcination time increases.

  19. Polonium-210 in tobacco

    International Nuclear Information System (INIS)

    Harley, N.H.; Cohen, B.S.; Tso, T.C.

    1978-01-01

    The purpose of this paper was to present the measurements that have been made on tobacco and tobacco products and to indicate the studies that show the amount of 210 Po transferred to mainstream smoke and inhaled. The amounts reported to be in the lung are summarized. The authors have shown what average values might be expected in the lung due to normal deposition and clearance of the smoke aerosol and to compare these values with the measurements. The average dose to cells in the bronchial epithelium was estimated for the activities reported to be on the bronchial surface, and a comparison of this dose with a known tumorigenic alpha dose was made

  20. "Chemical contraction" in rubidium-bismuth melts

    Science.gov (United States)

    Khairulin, R. A.; Abdullaev, R. N.; Stankus, S. V.

    2017-10-01

    The density and thermal expansion of liquid rubidium and rubidium-bismuth alloy containing 25.0 at % Bi were measured by the gamma-ray attenuation technique at temperatures from liquidus to 1000 K. The results of this study were compared with the data obtained by other authors. The molar volume of the Rb75Bi25 melt strongly deviates from the additivity rule for ideal solutions.

  1. Electrocatalytic activity of bismuth doped silver electrodes

    CERN Document Server

    Amjad, M

    2002-01-01

    Investigation of redox reactions on silver, and bismuth doped silver electrodes in aqueous KOH solutions, by using potentiostatic steady-state polarization technique, has been carried out. The redox wave potential and current displacements along with multiplicity of the latter have been examined. These electrodes were employed for the oxidation of organic molecules such as ethylamine in alkaline media. Subsequently, these electrodes were ranked with respect to their activity for the redox reactions. (author)

  2. Adsorption of volatile polonium and bismuth species on metals in various gas atmospheres. Pt. I. Adsorption of volatile polonium and bismuth on gold

    Energy Technology Data Exchange (ETDEWEB)

    Maugeri, Emilio Andrea; Neuhausen, Joerg; Dressler, Rugard; Piguet, David; Voegele, Alexander; Schumann, Dorothea [Paul Scherrer Institut (PSI), Villigen (Switzerland). Lab. for Radiochemistry; Eichler, Robert [Paul Scherrer Institut (PSI), Villigen (Switzerland). Lab. for Radiochemistry; Bern Univ. (Switzerland). Dept. for Chemistry and Biochemistry; Rijpstra, Kim [Ghent Univ., Zwijnaarde (Belgium). Center for Molecular Modeling (CMM); Cottenier, Stefaan [Ghent Univ., Zwijnaarde (Belgium). Center for Molecular Modeling (CMM); Ghent Univ., Zwijnaarde (Belgium). Dept. of Materials Science and Engineering

    2016-07-01

    Polonium isotopes are considered the most hazardous radionuclides produced during the operation of accelerator driven systems (ADS) when lead-bismuth eutectic (LBE) is used as the reactor coolant and as the spallation target material. In this work the use of gold surfaces for capturing polonium from the cover gas of the ADS reactor was studied by thermochromatography. The results show that gaseous monoatomic polonium, formed in dry hydrogen, is adsorbed on gold at 1058 K. Its adsorption enthalpy was calculated as -250±7 kJ mol{sup -1}, using a Monte Carlo simulation code. Highly volatile polonium species that were observed in similar experiments in fused silica columns in the presence of moisture in both inert and reducing gas were not detected in the experiments studying adsorption on gold surfaces. PoO{sub 2} is formed in both dry and moist oxygen, and its interaction with gold is characterized by transport reactions. The interaction of bismuth, present in large amounts in the atmosphere of the ADS, with gold was also evaluated. It was found that bismuth has a higher affinity for gold, compared to polonium, in an inert, reducing, and oxidizing atmosphere. This fact must be considered when using gold as a material for filtering polonium in the cover gas of ADS.

  3. Flame spray synthesis under a non-oxidizing atmosphere: Preparation of metallic bismuth nanoparticles and nanocrystalline bulk bismuth metal

    Energy Technology Data Exchange (ETDEWEB)

    Grass, Robert N.; Stark, Wendelin J. [Institute for Chemical and Bioengineering, ETH Zuerich (Switzerland)], E-mail: wendelin.stark@chem.ethz.ch

    2006-10-15

    Metallic bismuth nanoparticles of over 98% purity were prepared by a modified flame spray synthesis method in an inert atmosphere by oxygen-deficient combustion of a bismuth-carboxylate based precursor. The samples were characterized by X-ray diffraction, thermal analysis and scanning electron microscopy confirming the formation of pure, crystalline metallic bismuth nanoparticles. Compression of the as-prepared powder resulted in highly dense, nanocrystalline pills with strong electrical conductivity and bright metallic gloss.

  4. Doping of germanium telluride with bismuth tellurides

    International Nuclear Information System (INIS)

    Abrikosov, N.Kh.; Karpinskij, O.G.; Makalatiya, T.Sh.; Shelimova, L.E.

    1981-01-01

    Effect of germanium telluride doping with bismuth fellurides (Bi 2 Te 3 ; BiTe; Bi 2 Te) on phase transition temperature, lattice parameters and electrophysical properties of alloys is studied. It is shown that in alloys of GeTe-Bi 2 Te 3 (BiTe)(Bi 2 Te) cross sections solid solution of GeTe with Bi 2 Te 3 , characterized by deviation from stoichiometry, and germanium in the second phase the quantity of which increases during the transition from GeTe-Bi 2 Te 3 cross section to GeTe-Bi 2 Te are in equilibrium. Lower values of holes concentration and of electric conductivity and higher values of thermo e.m.f. coefficient in comparison with alloys of GeTe-Bi 2 Te 3 cross section with the same bismuth content are characterized for GeTe-Bi 2 Te cross section alloys. It is shown that in the range of GeTe-base solid solution the α→γ phase transformation which runs trough the two-phase region (α→γ) is observed with tellurium content increase. Extension of α-phase existence region widens with the bismuth content increase. Peculiarities of interatomic interaction in GeTe-base solid solutions with isovalent and heterovalent cation substitution are considered [ru

  5. Polonium-210 and lead-210 in marine food chains

    International Nuclear Information System (INIS)

    Heyraud, M.; Cherry, R.D.

    1979-01-01

    210 Po and 210 Pb have been measured systematically in whole animals, muscle and hepatopancreas of crustaceans and of molluscan cephalopods representative of a pelagic and benthic food chain. The same nuclides were also measured in liver, pyloric caecum, stomach contents and muscle of tuna. The concentration factors from sea water to whole animals were approximately constant along both food chains, being of the order of 10 4 for 210 Po and 10 2 for 210 Pb. The highest concentration factors were found in shrimp of the genus Sergestes. In muscle, the concentration factors were an order of magnitude less; in the hepatopancreas, they were an order of magnitude higher, reaching 10 6 in shrimp of the genus Sergestes. Such concentrations imply alpha-radiation doses of the order of 10 rem per year and more in this organ, which contains about 50 to 90% of the 210 Po in the whole animal in the 11 species analyzed. A detailed study of the intracellular behaviour of 210 Po in the hepatopancreas is clearly indicated. 210 Po can be used as a sensitive natural tracer in biological systems. Thus, feeding Meganyctiphanes norvegica in the laboratory on food low in 210 Po led to an approximate value of about 6 1/2 days for the biological half-life of 210 Po in the hepatopancreas of this euphausiid. Furthermore, the data on 210 Po and 210 Pb in the cephalopod hepatopancreas allowed the time of conservation of frozen squid which had been bought at the market to be estimated. (orig.) 891 AJ/orig. 892 MKO [de

  6. Polonium-210 and lead-210 in marine food chains

    Energy Technology Data Exchange (ETDEWEB)

    Heyraud, M [Musee Oceanographique (Monaco). International Lab. of Marine Radioactivity; Cherry, R D [Cape Town Univ. (South Africa). Dept. of Physics

    1979-01-01

    /sup 210/Po and /sup 210/Pb have been measured systematically in whole animals, muscle and hepatopancreas of crustaceans and of molluscan cephalopods representative of a pelagic and benthic food chain. The same nuclides were also measured in liver, pyloric caecum, stomach contents and muscle of tuna. The concentration factors from sea water to whole animals were approximately constant along both food chains, being of the order of 10/sup 4/ for /sup 210/Po and 10/sup 2/ for /sup 210/Pb. The highest concentration factors were found in shrimp of the genus Sergestes. In muscle, the concentration factors were an order of magnitude less; in the hepatopancreas, they were an order of magnitude higher, reaching 10/sup 6/ in shrimp of the genus Sergestes. Such concentrations imply alpha-radiation doses of the order of 10 rem per year and more in this organ, which contains about 50 to 90% of the /sup 210/Po in the whole animal in the 11 species analyzed. A detailed study of the intracellular behaviour of /sup 210/Po in the hepatopancreas is clearly indicated. /sup 210/Po can be used as a sensitive natural tracer in biological systems. Thus, feeding Meganyctiphanes norvegica in the laboratory on food low in /sup 210/Po led to an approximate value of about 6 1/2 days for the biological half-life of /sup 210/Po in the hepatopancreas of this euphausiid. Furthermore, the data on /sup 210/Po and /sup 210/Pb in the cephalopod hepatopancreas allowed the time of conservation of frozen squid which had been bought at the market to be estimated. (orig.) 891 AJ/orig. 892 MKO.

  7. Effect of excess bismuth on the dielectric and piezoelectric properties of strontium bismuth niobate ceramics

    International Nuclear Information System (INIS)

    Verma, Maya; Tanwar, Amit; Sreenivas, K.

    2013-01-01

    Excess Bismuth Strontium Bismuth Niobate (Sr 2 Bi 2 Nb 2 O 9 + x wt% Bi 2 O 3 ) ceramics were prepared using conventional solid state reaction method by varying x in the range (x=0%wt - 20%wt). X-ray diffraction studies reveal no significant shift in the peak positions as the Bi content increases from 0.0 to 5%wt. However, at a higher content of Bi beyond x = 5wt% secondary phases relating to Bi 2 O 3 are identified. The c-axis orientation is found to be minimum for SBN ceramic prepared with 5% excess bismuth whereas with further increase in excess Bi 2 O 3 addition during processing, SBN ceramics show a much stronger c-axis orientation. Room temperature dielectric constant measured at 100 KHz is found to increase from 117 to 130 with increase in Bi content from x = 0 to 10wt% suggesting Bi addition has make up for the bismuth losses at higher sintering temperature (1200℃), however with further increase in Bi content (x > 10wt%), the dielectric constant decreases, and could be due to the increased probability of segregation of Bi on the grains of SBN ceramics. The improvement in ferroelectric properties were obtained when the bismuth excess is increased from 0% to 5%. It may be observed that on increasing the excess bismuth to 5%, the transition temperature increases from 424 to 450℃, while further increasing to 10%, transition becomes slightly diffused and phase transition temperature gets decreased to 398℃, which may be due to the formation of secondary phase. 5% excess Bi is found to enhance the dielectric and ferroelectricity properties, and any further increase of Bi in excess (>10%) during processing is found to degrade the electrical and functional properties of SBN. (author)

  8. Polonium-210 and lead-210 in marine organisms

    International Nuclear Information System (INIS)

    Yamamoto, M.; Kuwabara, J.; Komura, K.; Ueno, K.

    1994-01-01

    The concentrations of 210 Po and 210 Pb were determined in about 30 species of marine organisms collected mainly from the north-eastern region of Japan to know the levels and distributions of these radionuclides and to estimate their intake levels from marine foods. 210 Po and 210 Pb showed a wide range of concentration in species: 0.6-26 and 0.04-0.54 Bq/kg (wet wt) in fishes, 0.5-220 and 0.2-43 Bq/kg (wet wt) in molluscs, echinoderms and chordatas, and 2.8-4.3 and 0.4-1.3 Bq/kg (wet wt) in algae, respectively. Higher accumulation of 210 Po relative to 210 Pb was found in all of the samples analyzed. The intake levels of 210 Po and 210 Pb by marine foods consumption were roughly estimated to be 0.48-0.69 and 0.022-0.042 Bq/d per person, respectively, on the basis of the statistical data on the consumption of seafood and/or production rates of marine foods. (author) 16 refs.; 6 tabs

  9. Polonium-210 in Bombay diet

    International Nuclear Information System (INIS)

    Khandekar, R.N.

    1977-01-01

    The results of the measurement of concentration levels of 210 Po in most of the common foods in the typical Bombay diet are given and estimates provided of the total daily intake of 210 Po by an individual of Bombay city. (U.K.)

  10. Polonium-210 in Bombay diet

    Energy Technology Data Exchange (ETDEWEB)

    Khandekar, R N [Bhabha Atomic Research Centre, Bombay (India). Air Monitoring Section

    1977-08-01

    The results of the measurement of concentration levels of /sup 210/Po in most of the common foods in the typical Bombay diet are given and estimates provided of the total daily intake of /sup 210/Po by an individual of Bombay city.

  11. Effectiveness of ranitidine bismuth citrate and proton pump inhibitor ...

    African Journals Online (AJOL)

    Effectiveness of ranitidine bismuth citrate and proton pump inhibitor based triple therapies of Helicobacter pylori in Turkey. ... Results: When we look at the eradication rates of the treatment groups, only two groups (ranitidine bismuth citrate and rabeprazole groups) had eradication rates greater than 80%, both at intention to ...

  12. Bismuth-silver mineralization in the Sergozerskoe gold occurrence

    Directory of Open Access Journals (Sweden)

    Kalinin A. A.

    2017-03-01

    Full Text Available Bismuth-silver mineralization attendant to gold mineralization in the Sergozerskoe gold occurrence has been studied in detail. Bi-Ag mineralization is connected with diorite porphyry dykes, which cut volcanic-sedimentary Lopian complexes of the Strel'ninsky greenstone belt – hornblendite and actinolite-chlorite amphibolites, biotite and bi-micaceous gneisses. Distribution of Bi-Ag mineralization similar to gold mineralization is controlled by 80 m thick zone of silicification. Bi minerals are found in brecciated diorite porphyry. Bismuth-silver mineralization includes native metals (bismuth, electrum, silver, tellurides (hedleyite, hessite, selenides (ikunolite, sulfides and sulfosalts of Bi and Ag (matildite, lillianite, eckerite, jalpaite, prustite, acanthite, a few undiagnosed minerals. All Bi and Ag minerals associate with galena. Composition of mineralization evolved from early to late stages of development, depending on intensity of rock alteration. The earliest Bi-Ag minerals were native bismuth and hedleyite formed dissemination in galena, and electrum with 30-45 mass.% Au. Later native bismuth was partly substituted by silver and bismuth sulfosalts and bismuth sulfides. The latest minerals were low-temperature silver sulfides eckerite, jalpaite, and acanthite, which were noted only in the most intensively altered rocks. As soon as the process of formation of Bi-Ag mineralization is the same as formation of gold, findings of bismuth-silver mineralization can serve as a positive exploration sign for gold in the region.

  13. Heat capacity, enthalpy and entropy of bismuth niobate and bismuth tantalate

    Czech Academy of Sciences Publication Activity Database

    Hampl, M.; Strejc, A.; Sedmidubský, D.; Růžička, K.; Hejtmánek, Jiří; Leitner, J.

    2006-01-01

    Roč. 179, - (2006), s. 77-80 ISSN 0022-4596 Institutional research plan: CEZ:AV0Z10100521 Keywords : heat capacity * heat of formation * heat content * bismuth perovskite Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.107, year: 2006

  14. Heat-Pipe Bismuth Laser; Examination of Laser Action at 4722A in Bismuth Vapor

    Science.gov (United States)

    1976-11-01

    11, 15(1975). of Type 6p 3 -6p 2 7s in the Bismuth Atomic Spectrum in Intermediate Coupling," Acta Physica Polonica A47, 231(1975). 19. A.N. Nesmeyanov...Calculated Transit n Probabilities and Lifetimes for the First Excited Configuration np (n+l)s in the Neutral As, Sb and Bi Atoms, " Physica Scripta

  15. Determination of 210Pb and 210Po in cigarette tobacco

    International Nuclear Information System (INIS)

    Peres, Ana Claudia

    1999-01-01

    Cigarette smoking is one of the important pathways that could contribute to enhance the radiation dose to man, due to the relatively large concentrations of 210 Pb and 210 Po found in tobacco leaves. In this work, concentrations of these two radionuclides were determined in eight of the most commercialized cigarette brands produced in Brazil. The samples analyzed were bought randomly in the market. The 210 Pb was determined by counting the beta activity of the 210 Bi in a gas flow proportional detector, after radiochemical separation and precipitation of the PbCr0 4 . The 210 Po was determined by alpha spectrometry, using a surface barrier detector, after radiochemical separation and spontaneous deposition of Po in copper disk. The results showed concentrations ranging from 11,9 to 30,2 mBq per gram of dry tobacco for 210 Pb and from 10,9 to 27,4 mBq per gram of dry tobacco for 210 Po. (author)

  16. Pb-210 and Po-210 from active volcanoes in Japan

    International Nuclear Information System (INIS)

    Komura, K.; Uchida, K.; Yamamoto, M.; Ueno, K.

    1991-01-01

    The concentration of Pb-210 and Po-210 in the surface air of volcanic areas is of considerable interest from the viewpoints of geochemistry, geophysics and also health physics, because these nuclides are the useful tracers for the estimation of the residence time or life time of aerosols, and give the significant radiation dose due to inhalation and ingestion through food stuffs. Since the establishment of Low Level Radioactivity Laboratory, Kanazawa University, in 1976, the measurement of environmental radioactivity has been one of the main subjects, and the measurement of Pb-210 and Po-210 in the surface air of Kagoshima was begun in 1987 to estimate the contribution from Volcano Sakurajima. In this study, the measurement of Pb-210 and Po-210 in air borne particles collected with air samplers, volcanic ash and lava of volcano Sakurajima of which the age of eruption is known. Moreover, the Po-210 in the volcanic gas and sulfur sublimate in the samples collected in four active volcanoes in Hokkaido was measured. The experiment and the results are reported. (K.I.)

  17. 210Pb and 210Po activities in French foodstuffs

    International Nuclear Information System (INIS)

    Renaud, Ph.; Roussel-Debet, S.; Pourcelot, L.; Thebault, H.; Loyen, J.; Gurriaran, R.

    2015-01-01

    The data on 210 Pb and 210 Po activities in French foodstuffs acquired during the last 15 years are numerous enough to derive reference values which will be usable to assess the dose to the French population due to the intake of these two natural radionuclides. The means and ranges are close to those observed in various countries and are most often higher than the reference values proposed by UNSCEAR. Mussels and oysters exhibit the highest 210 Po activities of all kinds of foodstuffs, with a mean value of 27 Bq.kg -1 fresh weight, followed by crustaceans and small fish species (anchovies, mullets, sardines, etc.) with 210 Po activities in the order of 3 to 10 Bq.k -1 fresh weight; cephalopods and other fish species presenting activities around 1 to 3 Bq.kg -1 fresh, close to the UNSCEAR reference value. Below these highest 210 Po activities are those of 210 Po and 210 Pb in terrestrial kinds of foodstuffs, by decreasing order: meats (around 1 Bq.kg -1 fresh), cereals (0.4 Bq.kg -1 ), leafy vegetables (0.3 Bq.kg -1 ), other vegetables and fruits (0.1 Bq.kg -1 ), and milk (from 0.03 to 0.1 Bq.L -1 ). (authors)

  18. Pb-210 and Po-210 from active volcanoes in Japan

    Energy Technology Data Exchange (ETDEWEB)

    Komura, K; Uchida, K; Yamamoto, M; Ueno, K [Kanazawa Univ. (Japan)

    1991-01-01

    The concentration of Pb-210 and Po-210 in the surface air of volcanic areas is of considerable interest from the viewpoints of geochemistry, geophysics and also health physics, because these nuclides are the useful tracers for the estimation of the residence time or life time of aerosols, and give the significant radiation dose due to inhalation and ingestion through food stuffs. Since the establishment of Low Level Radioactivity Laboratory, Kanazawa University, in 1976, the measurement of environmental radioactivity has been one of the main subjects, and the measurement of Pb-210 and Po-210 in the surface air of Kagoshima was begun in 1987 to estimate the contribution from Volcano Sakurajima. In this study, the measurement of Pb-210 and Po-210 in air borne particles collected with air samplers, volcanic ash and lava of volcano Sakurajima of which the age of eruption is known. Moreover, the Po-210 in the volcanic gas and sulfur sublimate in the samples collected in four active volcanoes in Hokkaido was measured. The experiment and the results are reported. (K.I.).

  19. Bismuth X-ray absorber studies for TES microcalorimeters

    International Nuclear Information System (INIS)

    Sadleir, J.E.; Bandler, S.R.; Brekosky, R.P.; Chervenak, J.; Figueroa-Feliciano, E.; Finkbeiner, F.; Iyomoto, N.; Kelley, R.L.; Kilbourne, C.A.; King, J.M.; Porter, F.S.; Robinson, I.K.; Saab, T.; Talley, D.J.

    2006-01-01

    Bismuth's large atomic number and low carrier density makes it an attractive X-ray absorber material for microcalorimeters. Bismuth's long Fermi wavelength and long mean free paths have motivated much interest in the fabrication of high quality bismuth films to study quantum size effects. Despite such incentives, fabrication of high quality bismuth films has proven difficult, and measured properties of such films are highly variable in the literature. Implementing a bismuth deposition process for TES (superconducting Transition Edge Sensor) device fabrication presents additional challenges particularly at interfaces due to the inherent granularity and surface roughness of its films, its low melting point, and its tendency to diffuse and form undesired intermetallic phases. We report observations of Bi-Cu and Bi-Au diffusion in our devices correlating with large shifts in T c (superconducting transition temperature). Using SEM and in situ R vs T annealing experiments we have been able to study these diffusion processes and identify their activation temperatures

  20. Bismuth-Based Quadruple Therapy with Bismuth Subcitrate, Metronidazole, Tetracycline and Omeprazole in the Eradication of Helicobacter pylori

    Directory of Open Access Journals (Sweden)

    Raymond Lahaie

    2001-01-01

    Full Text Available BACKGROUND: A previous study showed that 14 days of qid bismuth-based triple therapy with tetracycline 500 mg, metronidazole 250 mg and colloidal bismuth subcitrate 120 mg resulted in excellent Helicobacter pylori eradication rates (89.5%. The present study looked at a shorter treatment period by adding omeprazole and by reducing the dose of tetracycline.

  1. Polonium-210 budget in cigarettes

    International Nuclear Information System (INIS)

    Khater, A.E.M.

    2004-01-01

    Due to the relatively high activity concentrations of 210 Po and 210 Pb that are found in tobacco and its products, cigarette smoking highly increases the internal intake of both radionuclides and their concentrations in the lung tissues. That might contribute significantly to an increase in the internal radiation dose and in the number of instances of lung cancer observed among smokers. Samples of most frequently smoked fine and popular brands of cigarettes were collected from those available on the Egyptian market. 210 Po activity concentrations were measured by alpha spectrometry, using surface barrier detectors, following the radiochemical separation of polonium. Samples of fresh tobacco, wrapping paper, fresh filters, ash and post-smoking filters were spiked with 208 Po for chemical recovery calculation. The samples were dissolved using mineral acids (HNO 3 , HCl and HF). Polonium was spontaneously plated-out on stainless steel disks from diluted HCl solution. The 210 Po activity concentration in smoke was estimated on the basis of its activity in fresh tobacco and wrapping paper, fresh filter, ash and post-smoking filters. The percentages of 210 Po activity concentrations that were recovered from the cigarette tobacco to ash, post-smoking filters, and smokes were assessed. The results of this work indicate that the average (range) activity concentration of 210 Po in cigarette tobacco was 16.6 (9.7-22.5) mBq/cigarette. The average percentages of 210 Po content in fresh tobacco plus wrapping paper that were recovered by post-smoking filters, ash and smoke were 4.6, 20.7 and 74.7, respectively. Cigarette smokers, who are smoking one pack (20 cigarettes) per day, are inhaling on average 123 mBq/d of 210 Po and 210 Pb each. The annual effective doses were calculated on the basis of 210 Po and 210 Pb intake with the cigarette smoke. The mean values of the annual effective dose for smokers (one pack per day) were estimated to be 193 and 251 μSv from 210 Po and 210

  2. Quantum oscillations of conductivity in bismuth wires

    International Nuclear Information System (INIS)

    Condrea, Elena

    2011-01-01

    Measurements of the resistance of bismuth nanowires with several diameters and different quality reveal oscillations on the dependence of resistance under uniaxial strain at T = 4.2 K. Amplitude of oscillations is significant (38 %) at helium temperature and becomes smearing at T = 77 K. Observed oscillations originate from quantum size effect. A simple evaluation of period of oscillations allows us to identify the groups of carriers involved in transport. Calculated periods of 42.2 and 25.9 nm satisfy approximately the ratio 2:1 for two experimentally observed sets of oscillations from light and heavy electrons.

  3. An evaluated neutronic data file for bismuth

    International Nuclear Information System (INIS)

    Guenther, P.T.; Lawson, R.D.; Meadows, J.W.; Smith, A.B.; Smith, D.L.; Sugimoto, M.; Howerton, R.J.

    1989-11-01

    A comprehensive evaluated neutronic data file for bismuth, extending from 10 -5 eV to 20.0 MeV, is described. The experimental database, the application of the theoretical models, and the evaluation rationale are outlined. Attention is given to uncertainty specification, and comparisons are made with the prior ENDF/B-V evaluation. The corresponding numerical file, in ENDF/B-VI format, has been transmitted to the National Nuclear Data Center, Brookhaven National Laboratory. 106 refs., 10 figs., 6 tabs

  4. Optical Properties of Bismuth Tellurite Based Glass

    Directory of Open Access Journals (Sweden)

    Hooi Ming Oo

    2012-04-01

    Full Text Available A series of binary tellurite based glasses (Bi2O3x (TeO2100−x was prepared by melt quenching method. The density, molar volume and refractive index increase when bismuth ions Bi3+ increase, this is due to the increased polarization of the ions Bi3+ and the enhanced formation of non-bridging oxygen (NBO. The Fourier transform infrared spectroscopy (FTIR results show the bonding of the glass sample and the optical band gap, Eopt decreases while the refractive index increases when the ion Bi3+ content increases.

  5. Optical Properties of Bismuth Tellurite Based Glass

    Science.gov (United States)

    Oo, Hooi Ming; Mohamed-Kamari, Halimah; Wan-Yusoff, Wan Mohd Daud

    2012-01-01

    A series of binary tellurite based glasses (Bi2O3)x (TeO2)100−x was prepared by melt quenching method. The density, molar volume and refractive index increase when bismuth ions Bi3+ increase, this is due to the increased polarization of the ions Bi3+ and the enhanced formation of non-bridging oxygen (NBO). The Fourier transform infrared spectroscopy (FTIR) results show the bonding of the glass sample and the optical band gap, Eopt decreases while the refractive index increases when the ion Bi3+ content increases. PMID:22605999

  6. Lead-Bismuth-Eutectic Spallation Neutron Source for Nuclear Transmuter

    International Nuclear Information System (INIS)

    Gohar, Y.; Herceg, J.; Krajtl, L.; Micklich, B.; Pointer, D.; Saiveau, J.; Sofu, T.; Finck, P.

    2002-01-01

    A lead-bismuth eutectic (LBE) spallation target design concept has been developed for the subcritical multiplier (SCM) design of the accelerator-driven test facility (ADTF). The design is based on a coaxial geometrical configuration, which has been carefully analyzed and designed to achieve an optimum performance. The target design description, the results from the parametric studies, and the design analyses including neutronics, heat transfer, and hydraulics analyses are given in this paper. A detailed MCNPX geometrical model for the target has been developed to generate heating rates and nuclear responses in the structural material for the design process. The beam has a uniform distribution of 600 MeV protons and 5-MW total power. A small LBE buffer is optimized to reduce the irradiation damage in the SCM fuel elements from the scatter protons and the high-energy neutrons, to maximize the neutron yield to the SCM operation, and to provide inlet and outlet manifolds for the LBE coolant. A special attention has been given to the target window design to enhance its lifetime. The window volumetric heating is 766 W/cm 3 relative to 750 W/cm 3 in LBE for a 40-μA/cm 2 current density. The results show that the nuclear heating from the proton beam diminishes at about 32 cm along the beam axis in the LBE target material. The neutron contribution to the atomic displacement is in the range of 94 to ∼100% for the structure material outside the proton beam path. In the beam window, the neutron contribution is ∼74% and the proton beam is responsible for more than 95% of the total gas production. The proton contribution to the gas production vanishes outside the beam path. The LBE average velocity is ∼2 m/s. The heat transfer and the hydraulics analyses have been iterated to reduce the maximum temperature and the thermal stress level in the target window to enhance its operating life. (authors)

  7. Polonium-210 and lead-210 contamination of plants

    Energy Technology Data Exchange (ETDEWEB)

    Popova, O N; Taskaev, A I

    1977-01-01

    A model experiment with a water culture of barley grown in closed vessels, with an increased content of radon-222 in the air, has demonstrated an intensive contamination of the overground part and roots of the plant with polonium-210 and lead-210. Roots having no overground part were affected by radionuclides in a similar way as those of intact plants. Contamination was minimal in the plants grown from soil cultures.

  8. MiR-210 disturbs mitotic progression through regulating a group of mitosis-related genes

    OpenAIRE

    He, Jie; Wu, Jiangbin; Xu, Naihan; Xie, Weidong; Li, Mengnan; Li, Jianna; Jiang, Yuyang; Yang, Burton B.; Zhang, Yaou

    2012-01-01

    MiR-210 is up-regulated in multiple cancer types but its function is disputable and further investigation is necessary. Using a bioinformatics approach, we identified the putative target genes of miR-210 in hypoxia-induced CNE cells from genome-wide scale. Two functional gene groups related to cell cycle and RNA processing were recognized as the major targets of miR-210. Here, we investigated the molecular mechanism and biological consequence of miR-210 in cell cycle regulation, particularly ...

  9. Coating compositions comprising bismuth-alloyed zinc

    DEFF Research Database (Denmark)

    2008-01-01

    The present application discloses (i) a coating composition comprising a particulate zinc-based alloyed material, said material comprising 0.05-0.7% by weight of bismuth (Bi), the D50 of the particulate material being in the range of 2.5-30 µm; (ii) a coated structure comprising a metal structure...... having a first coating of the zinc-containing coating composition applied onto at least a part of the metal structure in a dry film thickness of 5-100 µm; and an outer coating applied onto said zinc-containing coating in a dry film thickness of 30-200 µm; (iii) a particulate zinc-based alloyed material......, wherein the material comprises 0.05-0.7%(w/w) of bismuth (Bi), and wherein the D50 of the particulate material is in the range of 2.5-30 µm; (iv) a composite powder consisting of at least 25%(w/w) of the particulate zinc-based alloyed material, the rest being a particulate material consisting of zinc...

  10. Liquid Lead-Bismuth Materials Test Loop

    International Nuclear Information System (INIS)

    Tcharnotskaia, Valentina; Ammerman, Curtt; Darling, Timothy; King, Joe; Li, Ning; Shaw, Don; Snodgrass, Leon; Woloshun, Keith

    2002-01-01

    We designed and built the Liquid Lead-Bismuth Materials Test Loop (MTL) to study the materials behavior in a flow of molten lead-bismuth eutectic (LBE). In this paper we present a description of the loop with main components and their functions. Stress distribution in the piping due to sustained, occasional and expansion loads is shown. The loop is designed so that a difference of 100 deg. C can be attained between the coldest and the hottest parts at a nominal flow rate of 8.84 GPM. Liquid LBE flow can be activated by a mechanical sump pump or by natural convection. In order to maintain a self-healing protective film on the surface of the stainless steel pipe, a certain concentration of oxygen has to be maintained in the liquid metal. We developed oxygen sensors and an oxygen control system to be implemented in the loop. The loop is outfitted with a variety of instruments that are controlled from a computer based data acquisition system. Initial experiments include preconditioning the loop, filling it up with LBE, running at uniform temperature and tuning the oxygen control system. We will present some preliminary results and discuss plans for the future tests. (authors)

  11. What is the structure of liquid Bismuth?

    International Nuclear Information System (INIS)

    Caspi, El'ad N; Greenberg, Yaron; Yahel, Eyal; Beuneu, Brigitte; Makov, Guy

    2012-01-01

    The structure of liquid Bismuth is probably the best-studied among elemental liquid metals because of a combination of the interesting physical properties of Bismuth and its excellent neutron scattering properties. Over the last six decades there have been more than 10 independent studies of the structure of liquid Bi, near the melting temperature. This remarkable number of measurements provides an opportunity to compare these results and to analyze the different sources of error contributing to the calculated pair distribution function. In the present contribution we analyze possible sources of error by varying the analysis procedure for a given measurement. By repeating a previous measurement in a new experimental configuration we demonstrate that an invariant (i.e. up to an absolute error) structure factor can be obtained. Transforming the structure factor into the radial distribution introduces new sources of error which causes the scatter to be greater than that required to resolve issues such as the existence of liquid-liquid phase transitions in Bi and to obtain correlation between thermo-physical properties and structure. We consider the contribution of different parameters when transforming the structure factor to the radial distribution function.

  12. Study of point defects in bismuth

    International Nuclear Information System (INIS)

    Bois, P.

    1987-03-01

    Single crystalline samples of bismuth, pure and n or p - doped by adding tellurium or tin, were electron irradiated at low temperature (4.2 K and 20 K). In the energy range 0.7 - 2.5 MeV, a displacement threshold energy of 13 eV and an athermal recombination volume of 150 atomic volumes were determined. Joint measurements of resistivity, magnetotransport and positron annihilation enabled to precised the nature of the annealing stages: 40-50 K, free migration of interstitials; 90-120 K long range migration of vacancy. Point defects have according to their nature a different effect on the electronic properties of bismuth: isolated Frenkel pairs are globally donnors with a charge of + 0.16 e- and the vacancy is donnor, which seems to attribute to it a negative formation volume. A simple model with non-deformating bands is no longer sufficient to explain the behaviour under irradiation: one has to take into account an acceptor level with a charge of - 0,27 e-, linked to the cascade-type defects and resonating with the valence band. It's position in the band overlap and it's width (8 meV) could be precised. In first approximation this coupling with less mobile carriers does not affect the simple additive rule which exists for relaxation times. Some yet obscure magnetic properties seem to be linked to this defect level [fr

  13. Development of lead-bismuth coolant technology for nuclear device

    International Nuclear Information System (INIS)

    Kamata, Kin-ya; Kitano, Teruaki; Ono, Mikinori

    2004-01-01

    Liquid lead-bismuth is a promising material as a future fast reactor coolant or an intensive neutron source material for accelerator driven transmutation system (ADS). To develop nuclear plants and their installations using lead-bismuth coolant for practical use, both coolant technologies, inhabitation process of steels and quality control of coolant, and total operation system for liquid lead-bismuth plants are required. Based on the experience of liquid metal coolant, Mitsui Engineering and Shipbuilding Co., Ltd. (MES) has completed the liquid lead-bismuth forced circulation loop and has acquired various engineering data on main components including economizer. As a result of tis operation, MES has developed key technologies of lead-bismuth coolant such as controlling of oxygen content in lead-bismuth and a purification of lead-bismuth coolant. MES participated in the national project, ''The Development of Accelerator Driven Transmutation System'', together with JAERI (Japan Atomic Energy Research Institute) and started corrosion test for beam window of ADS. (author)

  14. MiR-210 disturbs mitotic progression through regulating a group of mitosis-related genes.

    Science.gov (United States)

    He, Jie; Wu, Jiangbin; Xu, Naihan; Xie, Weidong; Li, Mengnan; Li, Jianna; Jiang, Yuyang; Yang, Burton B; Zhang, Yaou

    2013-01-07

    MiR-210 is up-regulated in multiple cancer types but its function is disputable and further investigation is necessary. Using a bioinformatics approach, we identified the putative target genes of miR-210 in hypoxia-induced CNE cells from genome-wide scale. Two functional gene groups related to cell cycle and RNA processing were recognized as the major targets of miR-210. Here, we investigated the molecular mechanism and biological consequence of miR-210 in cell cycle regulation, particularly mitosis. Hypoxia-induced up-regulation of miR-210 was highly correlated with the down-regulation of a group of mitosis-related genes, including Plk1, Cdc25B, Cyclin F, Bub1B and Fam83D. MiR-210 suppressed the expression of these genes by directly targeting their 3'-UTRs. Over-expression of exogenous miR-210 disturbed mitotic progression and caused aberrant mitosis. Furthermore, miR-210 mimic with pharmacological doses reduced tumor formation in a mouse metastatic tumor model. Taken together, these results implicate that miR-210 disturbs mitosis through targeting multi-genes involved in mitotic progression, which may contribute to its inhibitory role on tumor formation.

  15. Internal dosimetry of polonium-210

    International Nuclear Information System (INIS)

    Pucelj, B.

    2007-01-01

    On November 1, 2006, former Russian agent Alexander Litvinenko suddenly fell ill and was hospitalised. He died three weeks later, becoming the first known victim of lethal polonium-210 induced acute radiation syndrome. Po-210 is an alpha emitter and is not a radiological hazard as long as it remains outside the body. If taken into the body, much of Po-210 is subsequently excreted, mostly through faeces and some through urine and other pathways. After uptake by the blood, Po-210 is widely distributed through soft body tissues including bone marrow. The internal dose from polonium in the body gives rise to an increase in lifetime cancer risk. Very high radiation doses can cause severe damage to body tissues and organs and in the extreme can be fatal. The hazard function model was used to estimate the lethal levels of intake of Po-210. In case of Litvinenko the destruction of bone marrow and resulting failure of the immune system was most probably the main cause of death, likely to be compounded by damage caused by higher doses to other organs, including kidneys and liver. It was estimated that the ingestion of several hundreds MBq or just about a microgram of Po-210 can be lethal. (author)

  16. Properties of Nanostructure Bismuth Telluride Thin Films Using Thermal Evaporation

    Directory of Open Access Journals (Sweden)

    Swati Arora

    2017-01-01

    Full Text Available Bismuth telluride has high thermoelectric performance at room temperature; in present work, various nanostructure thin films of bismuth telluride were fabricated on silicon substrates at room temperature using thermal evaporation method. Tellurium (Te and bismuth (Bi were deposited on silicon substrate in different ratio of thickness. These films were annealed at 50°C and 100°C. After heat treatment, the thin films attained the semiconductor nature. Samples were studied by X-ray diffraction (XRD and scanning electron microscopy (SEM to show granular growth.

  17. Potential containment materials for liquid-lead and lead-bismuth eutectic spallation neutron source

    International Nuclear Information System (INIS)

    Park, J.J.; Butt, D.P.; Beard, C.A.

    1997-11-01

    Lead (Pb) and lead-bismuth eutectic (44Pb-56Bi) have been the two primary candidate liquid-metal target materials for the production of spallation neutrons. Selection of a container material for the liquid-metal target will greatly affect the lifetime and safety of the target subsystem. For the lead target, niobium-1 (wt%) zirconium (Nb-1Zr) is a candidate containment material for liquid lead, but its poor oxidation resistance has been a major concern. The oxidation rate of Nb-1Zr was studied based on the calculations of thickness loss due to oxidation. According to these calculations, it appeared that uncoated Nb-1Zr may be used for a one-year operation at 900 C at P O 2 = 1 x 10 -6 torr, but the same material may not be used in argon with 5-ppm oxygen. Coating technologies to reduce the oxidation of Nb-1Zr are reviewed, as are other candidate refractory metals such as molybdenum, tantalum, and tungsten. For the Pb-Bi target, three candidate containment materials are suggested based on a literature survey of the materials compatibility and proton irradiation tests: Croloy 2-1/4, modified 9Cr-1Mo, and 12Cr-1Mo (HT-9) steel. These materials seem to be used only if the lead-bismuth is thoroughly deoxidized and treated with zirconium and magnesium

  18. Contribution to the study of the geophysical behaviour of lead-210 by application of alpha spectrometry; Contribution a l'etude du comportement geophysique du plomb 210 par application de la spectrometrie alpha

    Energy Technology Data Exchange (ETDEWEB)

    Nezami, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1965-06-01

    A study of the changes in the lead-210 contents of rain-water and of water produced by melting polar ice has required the development of a method for dosing lead-210, an {alpha} emitter. This method is 40 times more sensitive than that which measures the lead-210 by bismuth-210, a ({beta} emitter. The first part of the report presents the study of a spectrometry using semiconductor detectors; a catalogue of a spectra shows the advantages of this method. In the second part will be found at first a new chemical separation method for polonium-210 and the results obtained with this method. The main results obtained on the geophysical behaviour of lead-210 are the following: - the monthly lead-210 and polonium-210 contents in rain water are approximately constant with time. - in the Gif-sur-Yvette region, the clean-up by 'dry fall-out' can attain 40 to 50 per cent of the total fall-out. - a study of Antarctic ice samples makes it possible to determine an annual accumulation rate equivalent to 13.8 cm of water and to show discrepancies in the periodic concentrations which correspond to the latest maxima of solar activity. - a balance is drawn up between the radon produced by the continents and the lead-210 fall-out. (author) [French] Une etude sur les variations de la teneur en plomb 210 des eaux de pluie et des eaux de fusion des glaces polaires a necessite la mise au point d'une methode de dosage du plomb 210 emetteur {alpha}. Cette methode permet d'obtenir une sensibilite quarante fois superieure a celle dosant le plomb 210 par le bismuth 210 emetteur {beta}. La premiere partie du travail presente l'etude de la spectrometrie {alpha} par detecteur a semiconducteurs, un catalogue de spectres {alpha} met en evidence les avantages de cette methode. Dans la deuxieme partie on trouvera en premier lieu une nouvelle methode chimique de separation du polonium 210 ainsi que les resultats obtenus grace a cette methode. Les principaux resultats sur le comportement geophysique du

  19. Contribution to the study of the geophysical behaviour of lead-210 by application of alpha spectrometry; Contribution a l'etude du comportement geophysique du plomb 210 par application de la spectrometrie alpha

    Energy Technology Data Exchange (ETDEWEB)

    Nezami, M. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1965-06-01

    A study of the changes in the lead-210 contents of rain-water and of water produced by melting polar ice has required the development of a method for dosing lead-210, an {alpha} emitter. This method is 40 times more sensitive than that which measures the lead-210 by bismuth-210, a ({beta} emitter. The first part of the report presents the study of a spectrometry using semiconductor detectors; a catalogue of a spectra shows the advantages of this method. In the second part will be found at first a new chemical separation method for polonium-210 and the results obtained with this method. The main results obtained on the geophysical behaviour of lead-210 are the following: - the monthly lead-210 and polonium-210 contents in rain water are approximately constant with time. - in the Gif-sur-Yvette region, the clean-up by 'dry fall-out' can attain 40 to 50 per cent of the total fall-out. - a study of Antarctic ice samples makes it possible to determine an annual accumulation rate equivalent to 13.8 cm of water and to show discrepancies in the periodic concentrations which correspond to the latest maxima of solar activity. - a balance is drawn up between the radon produced by the continents and the lead-210 fall-out. (author) [French] Une etude sur les variations de la teneur en plomb 210 des eaux de pluie et des eaux de fusion des glaces polaires a necessite la mise au point d'une methode de dosage du plomb 210 emetteur {alpha}. Cette methode permet d'obtenir une sensibilite quarante fois superieure a celle dosant le plomb 210 par le bismuth 210 emetteur {beta}. La premiere partie du travail presente l'etude de la spectrometrie {alpha} par detecteur a semiconducteurs, un catalogue de spectres {alpha} met en evidence les avantages de cette methode. Dans la deuxieme partie on trouvera en premier lieu une nouvelle methode chimique de separation du polonium 210 ainsi que les resultats obtenus grace a cette methode. Les principaux resultats sur le

  20. 7 CFR 210.13 - Facilities management.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Facilities management. 210.13 Section 210.13... Participation § 210.13 Facilities management. Link to an amendment published at 74 FR 66216, Dec. 15, 2009. (a..., the added text is set forth as follows: § 210.13 Facilities management. (c) Food safety program. The...

  1. Contents of /sup 210/Pb in food

    Energy Technology Data Exchange (ETDEWEB)

    Huang, X; Song, H

    1982-02-01

    The contents of /sup 210/Pb in 30 kinds of commonly used foods are given in the paper. After the radioactive equilibrium between /sup 210/Pb and /sup 210/Pb was nearly established in samples, the concentration of /sup 210/Pb was determined by the method of spontaneous deposition on silver disc. The contents of /sup 210/Pb then were calculated from that of /sup 210/Po. The average contents of /sup 210/Pb in corn, vegetable and meat were 0.14, 15.08 and 1.26 x 10/sup -14/ Ci/g respectively.

  2. Ultrasonic investigations of some bismuth borate glasses doped with ...

    Indian Academy of Sciences (India)

    Keywords. Bismuth borate glasses; elastic moduli; Makishima–Mackenzie model. 1. Introduction ... former because of the small field strength of Bi3+ ion. Bi2O3 ..... Typically, when the material undergoes a phase change, the value of the.

  3. Studies on bismuth carboxylates—synthesis and characterization of ...

    Indian Academy of Sciences (India)

    crystalline modification (4 ) of the previously reported coordination polymer, bismuth tris(picolinate), [Bi(2– .... no significant change in the IR spectrum or the melting behaviour between 4 .... lens et al.7 There are moderate differences in the.

  4. Polonium-210 as Weapon for Mass Destruction

    International Nuclear Information System (INIS)

    Koteng, A.O.

    2010-01-01

    Properties of Po-210 make it possible for its use as weapon of mass destruction. Po-210 occurs naturally in minute quantities in the human body, in Uranium ore (< 0.1 mg Po-210 / ton ) and as a product of Radon-222 gas decay chain. Po-210 also occurs as deposition on vegetation (tobacco leaves). Po-210 is produced by bombardment of Bi-209 with neutrons in a nuclear reactor. Russia produces 8 grams per year for export to USA market

  5. Characterization, Leaching, and Filtration Testing for Bismuth Phosphate Sludge (Group 1) and Bismuth Phosphate Saltcake (Group 2) Actual Waste Sample Composites

    International Nuclear Information System (INIS)

    Lumetta, Gregg J.; Buck, Edgar C.; Daniel, Richard C.; Draper, Kathryn; Edwards, Matthew K.; Fiskum, Sandra K.; Hallen, Richard T.; Jagoda, Lynette K.; Jenson, Evan D.; Kozelisky, Anne E.; MacFarlan, Paul J.; Peterson, Reid A.; Shimskey, Rick W.; Sinkov, Sergey I.; Snow, Lanee A.

    2009-01-01

    A testing program evaluating actual tank waste was developed in response to Task 4 from the M-12 External Flowsheet Review Team (EFRT) issue response plan.() The test program was subdivided into logical increments. The bulk water-insoluble solid wastes that are anticipated to be delivered to the Waste Treatment and Immobilization Plant (WTP) were identified according to type such that the actual waste testing could be targeted to the relevant categories. Eight broad waste groupings were defined. Samples available from the 222S archive were identified and obtained for testing. The actual waste-testing program included homogenizing the samples by group, characterizing the solids and aqueous phases, and performing parametric leaching tests. Two of the eight defined groups - bismuth phosphate sludge (Group 1) and bismuth phosphate saltcake (Group 2) - are the subjects of this report. The Group 1 waste was anticipated to be high in phosphorus and was implicitly assumed to be present as BiPO4 (however, results presented here indicate that the phosphate in Group 1 is actually present as amorphous iron(III) phosphate). The Group 2 waste was also anticipated to be high in phosphorus, but because of the relatively low bismuth content and higher aluminum content, it was anticipated that the Group 2 waste would contain a mixture of gibbsite, sodium phosphate, and aluminum phosphate. Thus, the focus of the Group 1 testing was on determining the behavior of P removal during caustic leaching, and the focus of the Group 2 testing was on the removal of both P and Al. The waste-type definition, archived sample conditions, homogenization activities, characterization (physical, chemical, radioisotope, and crystal habit), and caustic leaching behavior as functions of time, temperature, and hydroxide concentration are discussed in this report. Testing was conducted according to TP-RPP-WTP-467

  6. Synthesis and characterization of superconducting bismuthates

    International Nuclear Information System (INIS)

    Tang, Horngyi.

    1991-01-01

    A new electrosynthetic technique for low-temperature crystal growth of superconducting bismuthates was developed, and its utility demonstrated by growing various high-quality BiO 3 crystals. The crystals of Ba 1-x K x BiO 3 and Ba 1-x Rb x BiO 3 display their T c onset at 31.8k and 28k, respectively, using SQUID magnetometry. The structure of a KBiO 3 x H 2 O single crystal determined by single crystal x-ray diffraction confirms previous results from powder samples that it is isostructural with KSbO 3 . The crystals of Ba 1-x Cs x BiO 3 do not show superconductivity to 4k. Chemical vapor-transport experiments leading to the fabrication of MoS 2 /WSe 2 junctions were also performed and are described in detail

  7. Simultaneous determination of Ra-226, Ra-228 and Pb-210 using a successive coprecipitations techniques

    International Nuclear Information System (INIS)

    Vilhena Schayer Sabino, C. de; Kastner, S.M.S.; Amaral, A.M.

    1990-01-01

    Several techniques for determination of Ra-226, Ra228 and Pb-210. were developed and used in routine at CDTN in the laboratories of radiochemistry. The matrixes were: water and industrial wastes. Some problems of these techniques were the time spent for analyses and chemical separations, interferents, among others. Now-a-days the method in routine developed here is the one of successive coprecipitations, followed α and β countings of the Ra-226 and Ra-228 daughters. This method is based on coprecipitation, purification of barium radium sulfate with EDTA in acetic solution. Lead is dissolved, radium remains precipitated and suffers a new purification and the time for growing of their daughters is waited to be performed the simultaneous α and β countings for Ra-226 and Ra-228 determination. Pb-210 is analyzed in the floating of the first purification with a carrier of bismuth, and the time for Bi-210 growing is waited. Then it is precipitated as hydroxid, purified as phosphate and the β counting of Bi-210 is done. (author) [pt

  8. Polonium-210 and Lead-210 in food and tobacco products: transfer parameters and normal exposure and dose

    International Nuclear Information System (INIS)

    Watson, A.P.

    1985-01-01

    Food-chain transport of Pb-210 and Po-210 from soil to edible plant parts and from animal feed to meat and milk was evaluated from a review of literature. The degree of transfer was characterized by estimating concentration factors as well as the transfer coefficients B/sub v/, B/sub r/, f/sub m/, and f/sub f/. Global dietary intake of Pb-210 and Po-210 was also summarized, and 50-y dose estimates to target organs were calculated. The greatest estimated ingestion doses were those to populations with large dietary complements of animal protein in the form of seafood (Japan) or caribou/reindeer muscle and organ meats (Arctic Eskimos and Lapps). The origin and magnitude of inhalation exposure and dose from tobacco products were also assessed. For the majority of internal organs evaluated, the dose resulting from smoking commercially available tobacco products is comparable with or greater than the dose estimates for ingestion of naturally occurring dietary Pb-210 and Po-210. 79 refs

  9. Flotation atomic absorption determination of bismuth in nonferrous metal alloys

    International Nuclear Information System (INIS)

    Ososkov, V.K.; Plintus, A.M.; Kornelli, M.Eh.; Zakhariya, A.N.; Lozanova, E.V.

    1986-01-01

    Technique of flotation concentration and atomic absorption determination of bismuth microquantities in alloys on the basis of copper and zinc has been developed. Fine-dispersed EhDEh-10P anionite was used as a carrier in flotation concentration. State standard samples (SSS) of brasses and German silver were used as analysed objects. Effect of macrocomponents on the results of bismuth content determination has been studied. Satisfactory coincidence of the results obtained and SSS certificates is shown

  10. Platinum-Bismuth Bimetallic Catalysts: Synthesis, Characterization and Applications

    OpenAIRE

    Saucedo, Jose A, Jr; Xiao, Yang; Varma, Arvind

    2015-01-01

    Bimetallic catalysts have been explored and shown to exhibit unique characteristics which are not present in monometallic catalysts. Platinum is well known as an effective catalyst for oxidation and reduction reactions, and it can be made more effective when bismuth is introduced as a promotor. Thus, the effectiveness of the Pt-Bi catalyst was demonstrated in prior work. What is not clear, however, is the mechanism behind the catalyst function; why addition of bismuth to platinum decreases de...

  11. Antibacterial effect of bismuth subsalicylate nanoparticles synthesized by laser ablation

    International Nuclear Information System (INIS)

    Flores-Castañeda, Mariela; Vega-Jiménez, Alejandro L.; Almaguer-Flores, Argelia; Camps, Enrique; Pérez, Mario; Silva-Bermudez, Phaedra; Berea, Edgardo; Rodil, Sandra E.

    2015-01-01

    The antimicrobial properties of bismuth subsalicylate (BSS) nanoparticles against four opportunistic pathogens; E. coli, P. aeruginosa, S. aureus, and S. epidermidis were determined. BSS nanoparticles were synthesized by pulse laser ablation of a solid target in distilled water under different conditions. The nanoparticles were characterized using high-resolution transmission electron microscopy and absorption spectra and small angle X-ray scattering. The analysis shows that the colloids maintained the BSS structure and presented average particle size between 20 and 60 nm, while the concentration ranges from 95 to 195 mg/L. The antibacterial effect was reported as the inhibition ratio of the bacterial growth after 24 h and the cell viability was measured using the XTT assay. The results showed that the inhibition ratio of E. coli and S. epidermidis was dependant on the NPs size and/or concentration, meanwhile P. aeruginosa and S. aureus were more sensitive to the BSS nanoparticles independently of both the size and the concentration. In general, the BSS colloids with average particle size of 20 nm were the most effective, attaining inhibition ratios >80 %, similar or larger than those obtained with the antibiotic used as control. The results suggest that the BSS colloids could be used as effective antibacterial agents with potential applications in the medical area

  12. Antibacterial effect of bismuth subsalicylate nanoparticles synthesized by laser ablation

    Science.gov (United States)

    Flores-Castañeda, Mariela; Vega-Jiménez, Alejandro L.; Almaguer-Flores, Argelia; Camps, Enrique; Pérez, Mario; Silva-Bermudez, Phaedra; Berea, Edgardo; Rodil, Sandra E.

    2015-11-01

    The antimicrobial properties of bismuth subsalicylate (BSS) nanoparticles against four opportunistic pathogens; E. coli, P. aeruginosa, S. aureus, and S. epidermidis were determined. BSS nanoparticles were synthesized by pulse laser ablation of a solid target in distilled water under different conditions. The nanoparticles were characterized using high-resolution transmission electron microscopy and absorption spectra and small angle X-ray scattering. The analysis shows that the colloids maintained the BSS structure and presented average particle size between 20 and 60 nm, while the concentration ranges from 95 to 195 mg/L. The antibacterial effect was reported as the inhibition ratio of the bacterial growth after 24 h and the cell viability was measured using the XTT assay. The results showed that the inhibition ratio of E. coli and S. epidermidis was dependant on the NPs size and/or concentration, meanwhile P. aeruginosa and S. aureus were more sensitive to the BSS nanoparticles independently of both the size and the concentration. In general, the BSS colloids with average particle size of 20 nm were the most effective, attaining inhibition ratios >80 %, similar or larger than those obtained with the antibiotic used as control. The results suggest that the BSS colloids could be used as effective antibacterial agents with potential applications in the medical area.

  13. Antibacterial effect of bismuth subsalicylate nanoparticles synthesized by laser ablation

    Energy Technology Data Exchange (ETDEWEB)

    Flores-Castañeda, Mariela [Instituto Nacional de Investigaciones Nucleares (Mexico); Vega-Jiménez, Alejandro L., E-mail: argelia.almaguer@mac.com; Almaguer-Flores, Argelia [Universidad Nacional Autónoma de México, Facultad de Odontología, DEPeI, I (Mexico); Camps, Enrique; Pérez, Mario [Instituto Nacional de Investigaciones Nucleares (Mexico); Silva-Bermudez, Phaedra [Instituto Nacional de Rehabilitación, Unidad de Ingeniería de Tejidos, Terapia Celular y Medicina Regenerativa (Mexico); Berea, Edgardo [FarmaQuimia SA de CV. (Mexico); Rodil, Sandra E. [Universidad Nacional Autónoma de México, Instituto de Investigaciones en Materiales (Mexico)

    2015-11-15

    The antimicrobial properties of bismuth subsalicylate (BSS) nanoparticles against four opportunistic pathogens; E. coli, P. aeruginosa, S. aureus, and S. epidermidis were determined. BSS nanoparticles were synthesized by pulse laser ablation of a solid target in distilled water under different conditions. The nanoparticles were characterized using high-resolution transmission electron microscopy and absorption spectra and small angle X-ray scattering. The analysis shows that the colloids maintained the BSS structure and presented average particle size between 20 and 60 nm, while the concentration ranges from 95 to 195 mg/L. The antibacterial effect was reported as the inhibition ratio of the bacterial growth after 24 h and the cell viability was measured using the XTT assay. The results showed that the inhibition ratio of E. coli and S. epidermidis was dependant on the NPs size and/or concentration, meanwhile P. aeruginosa and S. aureus were more sensitive to the BSS nanoparticles independently of both the size and the concentration. In general, the BSS colloids with average particle size of 20 nm were the most effective, attaining inhibition ratios >80 %, similar or larger than those obtained with the antibiotic used as control. The results suggest that the BSS colloids could be used as effective antibacterial agents with potential applications in the medical area.

  14. In situ electron beam irradiated rapid growth of bismuth nanoparticles in bismuth-based glass dielectrics at room temperature

    International Nuclear Information System (INIS)

    Singh, Shiv Prakash; Karmakar, Basudeb

    2011-01-01

    In this study, in situ control growth of bismuth nanoparticles (Bi 0 NPs) was demonstrated in bismuth-based glass dielectrics under an electron beam (EB) irradiation at room temperature. The effects of EB irradiation were investigated in situ using transmission electron microscopy (TEM), selected-area electron diffraction and high-resolution transmission electron microscopy. The EB irradiation for 2–8 min enhanced the construction of bismuth nanoparticles with a rhombohedral structure and diameter of 4–9 nm. The average particle size was found to increase with the irradiation time. Bismuth metal has a melting point of 271 °C and this low melting temperature makes easy the progress of energy induced structural changes during in situ TEM observations. This is a very useful technique in nano-patterning for integrated optics and other applications.

  15. Photon nuclear scattering on lead and bismuth in the region of the giant resonance

    International Nuclear Information System (INIS)

    Tamas, Gabriel.

    1976-01-01

    The results of monochromatic photon nuclear scattering studies on natural lead and bismuth targets are presented. The cross sections for the inelastic scattering leading to the first excited levels of 204 Pb, 206 Pb and 207 Pb are important, in agreement with theoretical predictions. The elastic scattering amplitude is related to the total photon absorption by dispersion relations. It is then possible to determine the spin of resonances excited by the reaction studied. Precise measurements carried out between 14 and 20MeV revealed that the angular distribution cannot be explained by a single dipolar resonance. A quadrupolar resonance at E 2 =14MeV must be introduced [fr

  16. Studies of the balance 210Pb - 210Po in glasses; Estudios del equilibrio 210Pb - 210Po en vidrios

    Energy Technology Data Exchange (ETDEWEB)

    Torre Pérez, J. de la; Martín Sánchez, A.; Ruano Sánchez, A.B.

    2014-07-01

    Retrospective dosimetry requires measurement methods allowing the determination of Radon concentration in the past. One of the such methods is based on the direct measurement of 210Po implanted on the surface of objects, whose activity concentration (Bq/m2), is directly related to the cumulative exposure due to the concentration of 222Rn (Bq/m3) for long time. These determinations are possible taking into consideration the equilibrium between 210Po (T1/2 = 138.378 days) and its parent 210Pb (T1/2 = 22.3 years), being both radionuclides from the 222Rn progeny. In previous works about the determination of the conversion factor (ratio between the concentration of 210Po in objects and the retrospective 222Rn concentration in air), Corresponding equilibria between descendants were assumed. In this work, an experimental study about the equilibrium 210Pb - 210Po in glasses, which were previously exposed to some radon concentrations, has been performed. Two scenarios were studied: a place with, and another place without, continuous cumulative 222Rn concentration. Results were compared with those reached by theoretical calculations from the (Bateman) activity evolution equations. [Spanish] La dosimetría retrospectiva requiere métodos de medida que permitan la determinación de la concentración de radón en el pasado. Uno de estos métodos está basado en la medida directa del 210Po implantado sobre la superficie de objetos, cuya concentración de actividad (Bq/m2), está directamente relacionada con la exposición acumulativa debida a la concentración de 222Rn (Bq/m3) durante largos períodos de tiempo. Estas determinaciones son posibles gracias al equilibrio entre el 210Po (T1/2 = 138,378 días) y su progenitor, el 210Pb (T1/2 = 22,3 años), siendo ambos radionúclidos descendientes del 222Rn. En trabajos anteriores sobre la determinación del factor de conversión (relación entre la concentración de 210Po en los objetos y la concentración de 222Rn retrospectivo en

  17. Determination of 210Pb and 210Po in water samples

    International Nuclear Information System (INIS)

    Ayranov, M.; Tosheva, Z.; Kies, A.

    2004-01-01

    Lead-210 and Polonium-210 are naturally occurring members of the Uranium-238 decay series. They could be found in various environmental samples, such as groundwater, fish and shellfish, contributing an important component of the human natural radiation background. For this reason the development of a fast, reproducible and sensitive method for determination of 210 Pb and 210 Po is of a great concern. The aims of our study were to adopt procedures for radiochemical separation of these radionuclides and radioanalytical methods for their determination. The combination of electrochemical deposition, co-precipitation and extraction chromatography gives the opportunity for fast and effective radiochemical separation of the analytes. Polonium was spontaneously plated on copper disk from the stock solution. Lead was co-precipitated with Fe(OH) 3 and further purified by extraction chromatography on Sr Spec columns. Alpha spectra of polonium were collected on Canberra PIPS detectors with 900 mm 2 active surface. The activities of lead were determined by LSC (Gardian Wallac Oy). The minimum detectable activities for sample size 1000 mL and chemical yield of 88 % for the polonium and 85 % for the lead are presented. The proposed method proved to be fast, accurate and reproducible for routine determination of lead and polonium in environmental water samples. (authors)

  18. Excitation functions for quasi-elastic transfer reactions induced with heavy ions in bismuth

    International Nuclear Information System (INIS)

    Gardes, D.; Bimbot, R.; Maison, J.; Reilhac, L. de; Rivet, M.F.; Fleury, A.; Hubert, F.; Llabador, Y.

    1977-01-01

    The excitation functions for the production of 210 Bi, 210 Po, sup(207-211)At and 211 Rn through quasi-elastic transfer reactions induced with heavy ions in 209 Bi have been measured. The corresponding reactions involved the transfer of one neutron, one proton, two and three charges from projectile to target. The projectiles used were 12 C, 14 N, 16 O, 19 F, 20 Ne, 40 Ca, 56 Fe and 63 Cu. The experimental techniques involved target irradiations and off-line α and γ activity measurements. Chemical separations were used to solve specific problems. Careful measurements of incident energies and cross sections were performed close to the reaction thresholds

  19. Multi-year Surface Deposition of {sup 210}Pb and {sup 210}Po at Lisbon - Atmospheric Depositions of {sup 210}Pb and {sup 210}Po in Lisbon, Portugal

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Fernando P.; Oliveira, Joao M.; Alberto, G. [Instituto Superior Tecnico/ Campus Tecnologico e Nuclear, Universidade Tecnica de Lisboa, E.N. 10, 2686-953 Sacavem (Portugal)

    2014-07-01

    The long lived radon daughters {sup 210}Pb and {sup 210}Po were determined in samples of total atmospheric depositions obtained with surface collectors continuously operated during 5 years, near Lisbon. The average annual {sup 210}Pb flux was 66±12 Bq m{sup -2}, and the average annual {sup 210}Po flux was 8±3 Bq m{sup -2}, with an overall {sup 210}Po/{sup 210}Pb activity ratio of 0.15±0.06. Direct determination of the {sup 210}Pb atmospheric flux was compared with the {sup 210}Pb excess determined in soil surface layers along with atmospheric depositions of {sup 137}Cs. The deposition of atmospheric {sup 210}Pb was positively correlated with seasonal rainfall, while {sup 210}Po was mainly originated in soil particles re-suspension throughout the year and also in seasonal forest fires. Unusually high {sup 210}Po/{sup 210}Pb activity ratios, higher than unity, were occasionally recorded in atmospheric depositions and the sources and causes are discussed. Long time-series of {sup 210}Pb and {sup 210}Po deposition fluxes, as presented herein are useful to test and constrain parameters of the atmospheric Global Circulation Models. (authors)

  20. Potential laboratory health hazard of /sup 210/Pb and a simple procedure for separation of /sup 210/Pb from the daughters /sup 210/Bi and /sup 210/Po

    Energy Technology Data Exchange (ETDEWEB)

    Pounds, J G [Arkansas Univ., Little Rock (USA). Medical Center; Blakemore, W M [The National Center for Toxicological Research, Department of Health and Human Services, Food and Drug Administration, Jefferson, AR, USA

    1981-12-01

    Lead 210 (Radium D) is a naturally occurring radionuclide which is frequently used in toxicological studies due to its long half-life. The use of /sup 210/Pb in tracer studies poses two problems. First /sup 210/Pb, along with its daughters /sup 210/Bi and /sup 210/Po, presents a significant health hazard to laboratory personnel. Second, the presence of the daughter products may interfere with the detection of /sup 210/Pb, particularly by techniques which discriminate poorly between different radioactive emissions, e.g. autoradiography. The potential laboratory health hazards of /sup 210/Pb and its daughters are briefly reviewed and a simple dithiozone extraction procedure which allows quantitative separation of /sup 210/Pb from the daughters /sup 210/Po and /sup 210/Bi is described. The purified /sup 210/Pb may then be utilized to reduce the health hazard from the daughter products and to construct calibration curves for the quantitation of /sup 210/Pb in the presence of /sup 210/Bi and /sup 210/Po by liquid scintillation counting.

  1. Applications of PB-210/RA-226 and PO-210/PB-210 disequilibria in the study of marine geochemical processes

    International Nuclear Information System (INIS)

    Bacon, M.P.

    1976-02-01

    The distribution of 210 Pb and 210 Po in dissolved (less than 0.4 micron) and particulate (greater than 0.4 micron) phases was measured at ten stations in the tropical and eastern North Atlantic and at two stations in the Pacific. Both radionuclides occur principally in the dissolved phase. Unsupported 210 Pb activities, maintained by flux from the atmosphere, were present in the surface mixed layer and penetrated into the thermocline to depths of about 500 m. Dissolved 210 Po was ordinarily present in the mixed layer at less than equilibrium concentrations, suggesting rapid biological removal of this nuclide. Particulate matter was enriched in 210 Po, with 210 Po/ 210 Pb activity ratios greater than 1.0, similar to those reported for phytoplankton. Box-model calculations yield a 2-y residence time for 210 Pb and a 0.6-y residence time for 210 Po in the mixed layer. These residence times are considerably longer than the time calculated for turnover of particles in the mixed layer (about 0.1 y). At depths of 100 to 300 m, 210 Po maxima occurred and unsupported 210 Po was frequently present. Calculations indicate that at least 50 percent of the 210 Po removed from the mixed layer is re-cycled within the thermocline. Similar calculations for 210 Pb suggest much lower re-cycling efficiencies

  2. Radiochemical determination of 210Po

    International Nuclear Information System (INIS)

    Clarence, J.

    1961-04-01

    By spontaneous deposition of Po onto silver, and with the use of Po 208 as a tracer, the accurate spectrographic measurements are made possible. Quantitative recovery of Po 210 from radioactive cellulose filters is obtained by burning of samples in a golden lined calorimetric bomb. (author) [fr

  3. Bismuth ferrite as low-loss switchable material for plasmonic waveguide modulator

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia; Zhukovsky, Sergei; Lavrinenko, Andrei

    2014-01-01

    We propose new designs of plasmonic modulators, which can beused for dynamic signal switching in photonic integrated circuits. We studyperformance of a plasmonic waveguide modulator with bismuth ferrite as atunable material. The bismuth ferrite core is sandwiched between metalplates (metal...

  4. Polonium-210 as a poison

    International Nuclear Information System (INIS)

    Harrison, John; Leggett, Rich; Lloyd, David; Phipps, Alan; Scott, Bobby

    2007-01-01

    The death of Alexander Litvinenko on 23 November 2006 has brought into focus scientific judgements concerning the radiotoxicity of polonium-210 ( 210 Po). This paper does not consider the specific radiological circumstances surrounding the tragic death of Mr Litvinenko; rather, it provides an evaluation of published human and animal data and models developed for the estimation of alpha radiation doses from 210 Po and the induction of potentially fatal damage to different organs and tissues. Although uncertainties have not been addressed comprehensively, the reliability of key assumptions is considered. Concentrating on the possibility of intake by ingestion, the use of biokinetic and dosimetric models to estimate organ and tissue doses from 210 Po is examined and model predictions of the time-course of dose delivery are illustrated. Estimates are made of doses required to cause fatal damage, taking account of the possible effects of dose protraction and the relative biological effectiveness (RBE) of alpha particles compared to gamma and x-rays. Comparison of LD 50 values (dose to cause death for 50% of people) for different tissues with the possible accumulation of dose to these tissues suggests that bone marrow failure is likely to be an important component of multiple contributory causes of death occurring within a few weeks of an intake by ingestion. Animal data on the effects of 210 Po provide good confirmatory evidence of intakes and doses required to cause death within about 3 weeks. The conclusion is reached that 0.1-0.3 GBq or more absorbed to blood of an adult male is likely to be fatal within 1 month. This corresponds to ingestion of 1-3 GBq or more, assuming 10% absorption to blood. Well-characterised reductions in white cell counts would be observed. Bone marrow failure is likely to be compounded by damage caused by higher doses to other organs, including kidneys and liver. Even if the bone marrow could be rescued, damage to other organs can be expected

  5. Study of 210Po and 210Pb in the riverine environments of coastal Karnataka

    International Nuclear Information System (INIS)

    Narayana, Y.; Rajashekara, K.M.

    2010-01-01

    Activity of 210 Po and 210 Pb were measured in soil and sediment samples collected from the major rivers Kali, Sharavathi and Netravathi of Coastal Karnataka. The activity of these two radionuclides were determined by radiochemical separation of 210 Po and counting the activity using a ZnS(Ag) Alpha counter. The activity of 210 Pb was higher than that of 210 Po in the riverine environs. The 210 Po and 210 Pb content in sediment was found to increase with silt/clay and organic matter contents. However no significant correlation was found between the activity 210 Po and 210 Pb with pH in sediments. The activity of 210 Po and 210 Pb and influence of physico-chemical parameters on these radionuclides were studied and discussed in this paper.

  6. Po-210 excretion and radon exposure

    International Nuclear Information System (INIS)

    Breuer, F.; Clemente, G.F.

    1979-01-01

    A mathematical model is given to describe the metabolism of the 210 Po introduced into the systemic compartiments of the human body. The model has been based on the experimental data referred to the 210 Pb- 210 Po intake, excretion and body burden of members of the general italian population. The model fits also very well the experimental data of 210 Pb- 210 Po intake and excretion reported by other authors. The retention function of 210 Po in total body, soft tissue and bone has been evaluated together with the urinary excretion function and the absorbed fraction by ingestion. The model is very valuable to evaluate the lung exposure to Radon decay products on the basis of the 210 Pb- 210 Po urinary excretions

  7. Controlled synthesis of bismuth oxyiodide toward optimization of photocatalytic performance

    Energy Technology Data Exchange (ETDEWEB)

    Liao, Chenxing; Ma, Zhijun [State Key Laboratory of Luminescent Materials and Devices, School of Materials Science and Engineering, South China University of Technology, Wushan Road 381, Guangzhou 510641 (China); Chen, Xiaofeng, E-mail: chenxf@scut.edu.c [Biomaterials Research Institute, School of Materials Science and Engineering, South China University of Technology, Wushan Road 381, Guangzhou 510641 (China); He, Xin [School of Applied Physics and Materials, Wuyi University, Jiangmen 529020 (China); Qiu, Jianrong, E-mail: qjr@scut.edu.cn [State Key Laboratory of Luminescent Materials and Devices, School of Materials Science and Engineering, South China University of Technology, Wushan Road 381, Guangzhou 510641 (China)

    2016-11-30

    Highlights: • Different bismuth oxyiodide was synthesized. • The hollow Bi{sub 4}O{sub 5}I{sub 2} microspheres was obtained. • Formation mechanism of the hollow structure was discussed in detail. - Abstract: A new investigation on the variation rule of the structure, morphology, chemical composition and photocatalytic performance of bismuth oxyiodide synthesized by solvothermal method as a function of reaction conditions was performed here. The composition and morphology of the product could be determined by X-ray diffraction, thermogravimetric analysis and scanning electron microscopy. The results revealed that the particle size together with content of iodide in bismuth oxyiodide decrease with the increase of the concentration of reaction precursors. Hollow Bi{sub 4}O{sub 5}I{sub 2} microsphere with specific surface area as high as 120.88 m{sup 2} g{sup −1} can be easily synthesized when the concentration of the reaction precursors finally increased to 62.5 mM. Photocatalytic water purification performance of the as-prepared samples was evaluated by using Rhodamine B (RhB) as a model contaminant. The results revealed that the hollow Bi{sub 4}O{sub 5}I{sub 2} exhibited the best performance among all the bismuth oxyodide synthesized here for the degradation of RhB under visible light irradiation. Meanwhile, the formation mechanism of the hierarchical hollow structure of bismuth oxyiodide was investigated by the dissolution-recrystallization mechanism.

  8. Lead- or Lead-bismuth-cooled fast reactors

    International Nuclear Information System (INIS)

    Bouchter, J.C.; Courouau, J.L.; Dufour, P.; Guidez, J.; Latge, C.; Martinelli, L.; Renault, C.; Rimpault, G.

    2014-01-01

    Lead-cooled fast reactors are one of the 6 concepts retained for the 4. generation of nuclear reactors. So far no lead-cooled reactors have existed in the world except lead-bismuth-cooled reactors in soviet submarines. Some problems linked to the use of the lead-bismuth eutectic appeared but were satisfactorily solved by a more rigorous monitoring of the chemistry of the lead-bismuth coolant. Lead presents various advantages as a coolant: no reactivity with water and the air,a high boiling temperature and low contamination when irradiated. The main asset of the lead-bismuth alloy is the drop of the fusion temperature from 327 C degrees to 125 C degrees. The main drawback of using lead (or lead-bismuth) is its high corrosiveness with metals like iron, chromium and nickel. The high corrosiveness of the coolant implies low flow velocities which means a bigger core and consequently a bigger reactor containment. Different research programs in the world (in Europe, Russia and the USA) are reviewed in the article but it appears that the development of this type of reactor requires technological breakthroughs concerning materials and the resistance to corrosion. Furthermore the concept of lead-cooled reactors seems to be associated to a range of low output power because of the compromise between the size of the reactor and its resistance to earthquakes. (A.C.)

  9. Oxygen holes and hybridization in the bismuthates

    Science.gov (United States)

    Khazraie, Arash; Foyevtsova, Kateryna; Elfimov, Ilya; Sawatzky, George A.

    2018-02-01

    Motivated by the recently renewed interest in the superconducting bismuth perovskites, we investigate the electronic structure of the parent compounds A BiO3 (A = Sr, Ba) using ab initio methods and tight-binding (TB) modeling. We use the density functional theory (DFT) in the local density approximation (LDA) to understand the role of various interactions in shaping the A BiO3 band structure near the Fermi level. It is established that interatomic hybridization involving Bi-6 s and O-2 p orbitals plays the most important role. Based on our DFT calculations, we derive a minimal TB model and demonstrate that it can describe the properties of the band structure as a function of lattice distortions, such as the opening of a charge gap with the onset of the breathing distortion and the associated condensation of holes onto a1 g-symmetric molecular orbitals formed by the O-2 pσ orbitals on collapsed octahedra. We also derive a single band model involving the hopping of an extended molecular orbital involving both Bi-6 s and a linear combination of six O-2 p orbitals which provides a very good description of the dispersion and band gaps of the low energy scale bands straddling the chemical potential.

  10. Tunneling in cuprate and bismuthate superconductors

    International Nuclear Information System (INIS)

    Zasadzinski, J.F.; Huang, Qiang; Tralshawala, N.

    1991-10-01

    Tunneling measurements using a point-contact technique are reported for the following high temperature superconducting oxides: Ba 1-x K x BiO 3 (BKBO), Nd 2-x Ce x CuO 4 (NCCO), Bi 2 Sr 2 CaCu 2 O 7 (BSCCO) and Tl 2 Ba 2 CaCu 2 O x (TBCCO). For the bismuthate, BKBO, ideal, S-I-N tunneling characteristics are observed using a Au tip. The normalized conductance is fitted to a BCS density of states and thermal smearing only proving there is no fundamental limitation in BKBO for device applications. For the cuprates, the normalized conductance displays BCS-like characteristics, but with a broadening larger than from thermal smearing. Energy gap values are presented for each material. For BKBO and NCCO the Eliashberg functions, α 2 F(ω), obtained from the tunneling are shown to be in good agreement with neutron scattering results. Proximity effect tunneling studies are reported for Au/BSCCO bilayers and show that the energy gap of BSCCO can be observed through Au layers up to 600 Angstrom thick

  11. Use of Russian technology of ship reactors with lead-bismuth coolant in nuclear power

    International Nuclear Information System (INIS)

    Zrodnikov, A.V.; Chitaykin, V.I.; Gromov, B.F.; Grigoryv, O.G.; Dedoul, A.V.; Toshinsky, G.I.; Dragunov, Yu.G.; Stepanov, V.S.

    2000-01-01

    The experience of using lead-bismuth coolant in Russian nuclear submarine reactors has been presented. The fundamental statements of the concept of using the reactors cooled by lead-bismuth alloy in nuclear power have been substantiated. The results of developments for using lead bismuth coolant in nuclear power have been presented. (author)

  12. Prognostic Value of Bismuth Typing and Modified T-stage in Hilar Cholangiocarcinoma

    Directory of Open Access Journals (Sweden)

    Shengen Yi

    2015-01-01

    Conclusion: The majority of our patients with HCC were characterized as Subtype IV in Bismuth typing and Stage T3 in modified T-stage. Both Bismuth typing and modified T-stage showed prognostic value in HCC. Compared with Bismuth typing, modified T-stage is a better indicator of the resectability of HCC.

  13. Microstructure and electrical properties of bismuth and bismuth oxide deposited by magnetron sputtering UBM

    International Nuclear Information System (INIS)

    Otalora B, D. M.; Dussan, A.; Olaya F, J. J.

    2015-01-01

    In this work, bismuth (Bi) and bismuth oxide (Bi 2 O 3 ) thin films were prepared, at room temperature, by Sputtering Unbalanced Magnetron (UBM - Unbalance Magnetron) technique under glass substrates. Microstructural and electrical properties of the samples were studied by X-ray diffraction (XRD) and System for Measuring Physical Properties - PPMS (Physical Property Measurement System). Dark resistivity of the material was measured for a temperature range between 100 and 400 K. From the XRD measurements it was observed a polycrystalline character of the Bi associated to the presence of phases above the main peak, 2θ = 26.42 grades and a growth governed by a rhombohedral structure. Crystal parameters were obtained for both compounds, Bi and Bi 2 O 3 . From the analysis of the spectra of the conductivity as a function of temperature, it was established that the transport mechanism that governs the region of high temperature (T>300 K) is thermally activated carriers. From conductivity measurements the activation energies were obtained of 0.0094 eV and 0.015 eV for Bi 2 O 3 and Bi, respectively. (Author)

  14. Langmuir probe measurement of the bismuth plasma plume formed by an extreme-ultraviolet pulsed laser

    International Nuclear Information System (INIS)

    Pira, P; Burian, T; Kolpaková, A; Tichý, M; Kudrna, P; Daniš, S; Wild, J; Juha, L; Lančok, J; Vyšín, L; Civiš, S; Zelinger, Z; Kubát, P

    2014-01-01

    Properties of the plasma plume produced on a bismuth (Bi) target irradiated by a focused extreme-ultraviolet (XUV) capillary-discharge laser beam were investigated. Langmuir probes were used in both single- and double-probe arrangements to determine the electron temperature and the electron density, providing values of 1–3 eV and ∼10 13 –10 14  m −3 , respectively. Although the temperatures seem to be comparable with values obtained in ablation plasmas produced by conventional, long-wavelength lasers, the density is significantly lower. This finding indicates that the desorption-like phenomena are responsible for the plume formation rather than the ablation processes. A very thin Bi film was prepared on an MgO substrate by pulsed XUV laser deposition. The non-uniform, sub-monolayer character of the deposited bismuth film confirms the Langmuir probe's observation of the desorption-like erosion induced by the XUV laser on the primary Bi target. (paper)

  15. Spatial and depth variation of 210Po and 210Pb in monazite sand along HBRA of coastal Kerala

    International Nuclear Information System (INIS)

    D'Cunha, Primal; Narayana, Y.

    2013-01-01

    The samples collected from high background radiation area were analyzed for 210 Po and 210 Pb activities in order to understand their distribution, enrichment and depth profile in the beach sand. The 210 Po and 210 Pb activities vary from 1.85 to 31.27 Bq kg -1 and 9.77 to 132.30 Bq kg -1 respectively. The 210 Po/ 210 Pb indicate that the radionuclides 210 Po and 210 Pb are not in equilibrium and the accumulation of 210 Pb in sand is greater than for 210 Po. The spatial variations of 210 Po and 210 Pb activities were studied in detail. (author)

  16. 7 CFR 210.14 - Resource management.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Resource management. 210.14 Section 210.14 Agriculture... Participation § 210.14 Resource management. (a) Nonprofit school food service. School food authorities shall.... Expenditures of nonprofit school food service revenues shall be in accordance with the financial management...

  17. 46 CFR 132.210 - Classification.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Classification. 132.210 Section 132.210 Shipping COAST... Portable and Semiportable Fire Extinguishers § 132.210 Classification. (a) Each portable fire extinguisher... Classification Type Size Halon 1211, 1301, and 1211-1301 mixtures kgs. (lbs.) Foam, liters (gallons) Carbon...

  18. 49 CFR 195.210 - Pipeline location.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Pipeline location. 195.210 Section 195.210 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... PIPELINE Construction § 195.210 Pipeline location. (a) Pipeline right-of-way must be selected to avoid, as...

  19. 15 CFR 280.210 - Discovery.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Discovery. 280.210 Section 280.210... STANDARDS AND TECHNOLOGY, DEPARTMENT OF COMMERCE ACCREDITATION AND ASSESSMENT PROGRAMS FASTENER QUALITY Enforcement § 280.210 Discovery. (a) General. The parties are encouraged to engage in voluntary discovery...

  20. 7 CFR 210.3 - Administration.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Administration. 210.3 Section 210.3 Agriculture... CHILD NUTRITION PROGRAMS NATIONAL SCHOOL LUNCH PROGRAM General § 210.3 Administration. (a) FNS. FNS will act on behalf of the Department in the administration of the Program. Within FNS, the CND will be...

  1. 38 CFR 51.210 - Administration.

    Science.gov (United States)

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Administration. 51.210 Section 51.210 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS (CONTINUED) PER DIEM FOR NURSING HOME CARE OF VETERANS IN STATE HOMES Standards § 51.210 Administration. A facility must be...

  2. 42 CFR 93.210 - Good faith.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Good faith. 93.210 Section 93.210 Public Health... MISCONDUCT Definitions § 93.210 Good faith. Good faith as applied to a complainant or witness, means having a... allegation or cooperation with a research misconduct proceeding is not in good faith if made with knowing or...

  3. 22 CFR 210.640 - Employee.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Employee. 210.640 Section 210.640 Foreign... (FINANCIAL ASSISTANCE) Definitions § 210.640 Employee. (a) Employee means the employee of a recipient directly engaged in the performance of work under the award, including— (1) All direct charge employees; (2...

  4. 22 CFR 210.655 - Individual.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Individual. 210.655 Section 210.655 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT GOVERNMENTWIDE REQUIREMENTS FOR DRUG-FREE WORKPLACE (FINANCIAL ASSISTANCE) Definitions § 210.655 Individual. Individual means a natural person. ...

  5. 4 CFR 21.0 - Definitions.

    Science.gov (United States)

    2010-01-01

    ... at GAO. (g) Alternative dispute resolution encompasses various means of resolving cases expeditiously... 4 Accounts 1 2010-01-01 2010-01-01 false Definitions. 21.0 Section 21.0 Accounts GOVERNMENT ACCOUNTABILITY OFFICE GENERAL PROCEDURES BID PROTEST REGULATIONS § 21.0 Definitions. (a)(1) Interested party...

  6. 19 CFR 210.24 - Interlocutory appeals.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Interlocutory appeals. 210.24 Section 210.24 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Motions § 210.24 Interlocutory appeals. Rulings by the administrative...

  7. 19 CFR 210.35 - Prehearing conferences.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Prehearing conferences. 210.35 Section 210.35 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Prehearing Conferences and Hearings § 210.35 Prehearing conferences...

  8. 19 CFR 210.19 - Intervention.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Intervention. 210.19 Section 210.19 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Motions § 210.19 Intervention. Any person desiring to intervene in an...

  9. 19 CFR 210.32 - Subpoenas.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Subpoenas. 210.32 Section 210.32 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Discovery and Compulsory Process § 210.32 Subpoenas. (a) Application for issuance...

  10. 19 CFR 210.25 - Sanctions.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Sanctions. 210.25 Section 210.25 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Motions § 210.25 Sanctions. (a)(1) Any party may file a motion for sanctions for...

  11. 19 CFR 210.2 - General policy.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false General policy. 210.2 Section 210.2 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Rules of General Applicability § 210.2 General policy. It is the policy of the...

  12. 19 CFR 210.22 - [Reserved

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false [Reserved] 210.22 Section 210.22 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Motions § 210.22 [Reserved] ...

  13. 19 CFR 210.38 - Record.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Record. 210.38 Section 210.38 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Prehearing Conferences and Hearings § 210.38 Record. (a) Definition of the record...

  14. 19 CFR 210.64 - Interlocutory appeals.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Interlocutory appeals. 210.64 Section 210.64 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Temporary Relief § 210.64 Interlocutory appeals. There will be no...

  15. 19 CFR 210.37 - Evidence.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Evidence. 210.37 Section 210.37 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Prehearing Conferences and Hearings § 210.37 Evidence. (a) Burden of proof. The...

  16. 19 CFR 210.13 - The response.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false The response. 210.13 Section 210.13 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Pleadings § 210.13 The response. (a) Time for response. Except as provided in...

  17. 19 CFR 210.18 - Summary determinations.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Summary determinations. 210.18 Section 210.18 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Motions § 210.18 Summary determinations. (a) Motions for summary...

  18. 19 CFR 210.29 - Interrogatories.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Interrogatories. 210.29 Section 210.29 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Discovery and Compulsory Process § 210.29 Interrogatories. (a) Scope; use at...

  19. 19 CFR 210.26 - Other motions.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Other motions. 210.26 Section 210.26 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Motions § 210.26 Other motions. Motions pertaining to discovery shall be filed in...

  20. 19 CFR 210.71 - Information gathering.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Information gathering. 210.71 Section 210.71 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Enforcement Procedures and Advisory Opinions § 210.71 Information...

  1. 19 CFR 210.28 - Depositions.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Depositions. 210.28 Section 210.28 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Discovery and Compulsory Process § 210.28 Depositions. (a) When depositions may be...

  2. 19 CFR 210.16 - Default.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Default. 210.16 Section 210.16 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Motions § 210.16 Default. (a) Definition of default. (1) A party shall be found in...

  3. 19 CFR 210.62 - Evidentiary hearing.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Evidentiary hearing. 210.62 Section 210.62 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Temporary Relief § 210.62 Evidentiary hearing. An opportunity for a hearing in...

  4. 19 CFR 210.3 - Definitions.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Definitions. 210.3 Section 210.3 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Rules of General Applicability § 210.3 Definitions. As used in this part...

  5. 19 CFR 210.15 - Motions.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Motions. 210.15 Section 210.15 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Motions § 210.15 Motions. (a) Presentation and disposition. (1) During the period...

  6. Concentration of 210Po in cigars

    International Nuclear Information System (INIS)

    Kelecom, Alphonse; Gouvea, Rita C.S.; Santos, Pedro L.

    2000-01-01

    210 Po concentrations have been determined in 57 different cigar brands manufactured in 11 countries. Cuban and American cigars showed the lowest 210 Po content. The mean levels of 210 Po in Brazilian cigars were almost equal to those of European and Dominican cigars, and somewhat lower than cigars from Central American countries. (author)

  7. 28 CFR 36.210 - Smoking.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Smoking. 36.210 Section 36.210 Judicial Administration DEPARTMENT OF JUSTICE NONDISCRIMINATION ON THE BASIS OF DISABILITY BY PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES General Requirements § 36.210 Smoking. This part does not preclude the prohibition of, or the imposition of...

  8. 46 CFR 121.210 - Heating equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Heating equipment. 121.210 Section 121.210 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... SYSTEMS AND EQUIPMENT Cooking and Heating § 121.210 Heating equipment. (a) Each heater must be so...

  9. 46 CFR 184.210 - Heating equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Heating equipment. 184.210 Section 184.210 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Cooking and Heating § 184.210 Heating equipment...

  10. 12 CFR 411.210 - Reporting.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Reporting. 411.210 Section 411.210 Banks and Banking EXPORT-IMPORT BANK OF THE UNITED STATES NEW RESTRICTIONS ON LOBBYING Activities by Own Employees § 411.210 Reporting. No reporting is required with respect to payments of reasonable compensation made...

  11. 22 CFR 210.665 - State.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false State. 210.665 Section 210.665 Foreign... (FINANCIAL ASSISTANCE) Definitions § 210.665 State. State means any of the States of the United States, the District of Columbia, the Commonwealth of Puerto Rico, or any territory or possession of the United States. ...

  12. 29 CFR 1603.210 - Discovery.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 4 2010-07-01 2010-07-01 false Discovery. 1603.210 Section 1603.210 Labor Regulations... GOVERNMENT EMPLOYEE RIGHTS ACT OF 1991 Hearings § 1603.210 Discovery. (a) Unless otherwise ordered by the administrative law judge, discovery may begin as soon as the complaint has been transmitted to the administrative...

  13. 21 CFR 173.210 - Acetone.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acetone. 173.210 Section 173.210 Food and Drugs..., Lubricants, Release Agents and Related Substances § 173.210 Acetone. A tolerance of 30 parts per million is established for acetone in spice oleoresins when present therein as a residue from the extraction of spice. ...

  14. 45 CFR 604.210 - Reporting.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 3 2010-10-01 2010-10-01 false Reporting. 604.210 Section 604.210 Public Welfare Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION NEW RESTRICTIONS ON LOBBYING Activities by Own Employees § 604.210 Reporting. No reporting is required with respect to payments of...

  15. 45 CFR 1230.210 - Reporting.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 4 2010-10-01 2010-10-01 false Reporting. 1230.210 Section 1230.210 Public Welfare Regulations Relating to Public Welfare (Continued) CORPORATION FOR NATIONAL AND COMMUNITY SERVICE NEW RESTRICTIONS ON LOBBYING Activities by Own Employees § 1230.210 Reporting. No reporting is...

  16. 24 CFR 1710.210 - Roads.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Roads. 1710.210 Section 1710.210... (INTERSTATE LAND SALES REGISTRATION PROGRAM) LAND REGISTRATION Reporting Requirements § 1710.210 Roads. (a) State the estimated cost to the developer of the proposed road system. (b) If the developer is to...

  17. Variation of 210Po and 210Pb Profile in the Sediment Core of Sarawak Coastal Waters

    International Nuclear Information System (INIS)

    Zal U'yun Wan Mahmood; Che Abd Rahim Mohamed; Zaharudin Ahmad; Abdul Kadir Ishak

    2008-01-01

    This study was performed to observe the variation in the distribution of 210 Po and 210 Pb through their activity vertical profile and 210 Po/ 210 Pb activity ratio in the sediment cores that were taken at some sampling stations in the Sarawak coastal waters. It was found that the distribution profile of those radionuclide in the sediment cores varied depending on the sampling location and ANOVA analysis shows significant difference at 95% confidence level for activities of 210 Po (p = 0.000), 210 Pb (p = 0.035) and 210 Po/ 210 Pb (p = 0.000) at all study locations. Generally, the measured activity of 210 Po and 210 Pb ranged from 337 to 2460 Bq/ kg, 11 to 84 Bq/ kg at SR 01; 224 to 2008 Bq/ kg, 6 to 80 Bq/ kg at SR 02; 119 to 1595 Bq/ kg, 6 to 84 Bq/ kg at SR 03; 241 to 2294 Bq/ kg, 5 to 82 Bq/ kg at SR 04 and 175 to 1340 Bq/ kg, 4 to 44 Bq/ kg at SR 05, respectively. In those range it was found that 210 Po activities were higher than 210 Pb with average of 210 Po/ 210 Pb ratios at all stations were from 20 to 35. The variation in the distribution profile for the radionuclides are believed to be influenced by some environmental factors and have strong correlation between the radionuclide distribution and the sediment composition of silt ( 210 Po: r = 0.701 and 210 Pb: r = 0.648), water depth ( 210 Po: r = -0.647) and the distance from the sampling station to the main land ( 210 Po: r = 0.746 and 210 Pb: r = 0.975). Those factors are a major contributions on the variation of 210 Po and 210 Pb in the samples. (author)

  18. 210Po and 210Pb activity concentration in the coral bands of Pulau Tuba, Langkawi

    International Nuclear Information System (INIS)

    Lee Jen Nie; Che Abdul Rahim Mohamed; Zaharuddin Ahmad

    2007-01-01

    We examined the concentrations of 210 Po and 210 Pb in each layers of coral banding of coral skeletons. Concentrations of 210 Po and 210 Pb in massive corals (i.e. Porites, Favites, Platygyra and Goniostrea) from Pulau Tuba, Langkawi were measured using the Alpha-Spectrometry. The concentrations of 210 Po were higher than the concentrations of 210 Pb. This may due to continuing source of 210 Po from 210 Pb. Highest concentration on 210 Po in coral banding was 48.30 ± 28.53 Bq/ kg, meanwhile for 210 Pb was 12.86 ± 5.80 Bq/ kg. The ratios of 210 Po/ 210 Pb were in the range of 2.21 to 5.49. The variation activity concentrations of 210 Po and 210 Pb in the coral bands are important to consider in using coral as retrospective study of environmental changes. The coral can represent the total of 210 Po and 210 Pb in the surrounding water for the past few years. (author)

  19. Investigation of 210Po/210Pb in terrestrial environment of uranium mineralized area of Jaduguda

    International Nuclear Information System (INIS)

    Sethy, N.K.; Jha, V.N.; Singh, S.; Sharma, B.D.; Sahoo, S.K.; Jha, S.K.; Tripathi, R.M.

    2018-01-01

    Soil is the major components for evaluation of migration characteristics and distribution of radionuclides like 210 Po and 210 Pb in a terrestrial ecosystem. In this study spatial profile of 210 Po in to soil and its equilibrium status with 210 Pb in the terrestrial environment have been studied and correlated with basic soil quality parameters

  20. Ra-226, Pb-210, and Po-210 in the Black Forest

    International Nuclear Information System (INIS)

    Schuettelkopf, H.; Kiefer, H.

    1981-01-01

    By measuring Pb-210, Po-210 and Ra 226 in air, water, ground, plants, and food samples the concentration ranges of the radionuclide and the transfer factor important for the calculation of the ingestion dose of man were determined. Po 210 was found to have the lowest radiotoxicity. The highest Po-210 concentrations were found in protein-containing food. (DG) [de

  1. 210Po and 210Pb in food chains lichen - reindeer - man

    International Nuclear Information System (INIS)

    Solatie, D.; Yunttila, M.; Vesterbakka, P.

    2006-01-01

    Migration of 210 Po and its precursor 210 Pb from radioactive fallout through food chain lichen - reindeer - man is studied. Samples of lichens, leaves, grass, mushrooms, soils, and samples of reindeer tissues are selected; their specific radioactivity and ratio 210 Po/ 210 Pb are determined [ru

  2. Numerical Modeling of Lead Oxidation in Controlled Lead Bismuth Eutectic Systems: Chemical Kinetics and Hydrodynamic Effects

    International Nuclear Information System (INIS)

    Wu, Chao; Kanthi Kiran Dasika; Chen, Yitung; Moujaes, Samir

    2002-01-01

    Using liquid Lead-Bismuth Eutectic (LBE) as coolant in nuclear systems has been studied for more than 50 years. And LBE has many unique nuclear, thermo physical and chemical attributes which are attractive for practical application. But, corrosion is one of the greatest concerns in using liquid Lead-Bismuth Eutectic (LBE) as spallation target in the Accelerator-driven Transmutation of Waste (ATW) program. Los Alamos National Laboratory has designed and built the Liquid Lead-Bismuth Materials Test Loop (MTL) to study the materials behavior in a flow of molten LBE. A difference of 100 deg. C was designed between the coldest and the hottest parts at a nominal flow rate of 8.84 GPM. Liquid LBE flow was activated by a mechanical sump pump or by natural convection. In order to maintain a self-healing protective film on the surface of the stainless steel pipe, a certain concentration of oxygen has to be maintained in the liquid metal. Therefore, it is of importance to understand what the oxygen concentrations are in the LBE loop related to the corrosion effects on the metal surface, the temperature profiles, the flow rates, and diffusion rates through the metal surface. The chemical kinetics also needs to be fully understood in the corrosion processes coupled with the hydrodynamics. The numerical simulation will be developed and used to analyze the system corrosion effects with different kind of oxygen concentrations, flow rates, chemical kinetics, and geometries. The hydrodynamics modeling of using computational fluid dynamics will provide the necessary the levels of oxygen and corrosion products close to the boundary or surface. This paper presents an approach towards the above explained tasks by analyzing the reactions between the Lead and oxygen at a couple of sections in the MTL. Attempt is also made to understand the surface chemistry by choosing an example model and estimating the near wall surface concentration values for propane and oxygen. (authors)

  3. Bismuth iron oxide thin films using atomic layer deposition of alternating bismuth oxide and iron oxide layers

    Energy Technology Data Exchange (ETDEWEB)

    Puttaswamy, Manjunath; Vehkamäki, Marko [University of Helsinki, Department of Chemistry, P.O. Box 55, FI-00014 Helsinki (Finland); Kukli, Kaupo, E-mail: kaupo.kukli@helsinki.fi [University of Helsinki, Department of Chemistry, P.O. Box 55, FI-00014 Helsinki (Finland); University of Tartu, Institute of Physics, W. Ostwald 1, EE-50411 Tartu (Estonia); Dimri, Mukesh Chandra [National Institute of Chemical Physics and Biophysics, Akadeemia tee 23, EE-12618 Tallinn (Estonia); Kemell, Marianna; Hatanpää, Timo; Heikkilä, Mikko J. [University of Helsinki, Department of Chemistry, P.O. Box 55, FI-00014 Helsinki (Finland); Mizohata, Kenichiro [University of Helsinki, Department of Physics, P.O. Box 64, FI-00014 Helsinki (Finland); Stern, Raivo [National Institute of Chemical Physics and Biophysics, Akadeemia tee 23, EE-12618 Tallinn (Estonia); Ritala, Mikko; Leskelä, Markku [University of Helsinki, Department of Chemistry, P.O. Box 55, FI-00014 Helsinki (Finland)

    2016-07-29

    Bismuth iron oxide films with varying contributions from Fe{sub 2}O{sub 3} or Bi{sub 2}O{sub 3} were prepared using atomic layer deposition. Bismuth (III) 2,3-dimethyl-2-butoxide, was used as the bismuth source, iron(III) tert-butoxide as the iron source and water vapor as the oxygen source. The films were deposited as stacks of alternate Bi{sub 2}O{sub 3} and Fe{sub 2}O{sub 3} layers. Films grown at 140 °C to the thickness of 200–220 nm were amorphous, but crystallized upon post-deposition annealing at 500 °C in nitrogen. Annealing of films with intermittent bismuth and iron oxide layers grown to different thicknesses influenced their surface morphology, crystal structure, composition, electrical and magnetic properties. Implications of multiferroic performance were recognized in the films with the remanent charge polarization varying from 1 to 5 μC/cm{sup 2} and magnetic coercivity varying from a few up to 8000 A/m. - Highlights: • Bismuth iron oxide thin films were grown by atomic layer deposition at 140 °C. • The major phase formed in the films upon annealing at 500 °C was BiFeO{sub 3}. • BiFeO{sub 3} films and films containing excess Bi favored electrical charge polarization. • Slight excess of iron oxide enhanced saturative magnetization behavior.

  4. Characterization of bismuth nanospheres deposited by plasma focus device

    Energy Technology Data Exchange (ETDEWEB)

    Ahmad, M., E-mail: cscientific2@aec.org.sy [IBA Laboratory, Chemistry Department, Atomic Energy Commission of Syria, P.O. Box 6091, Damascus (Syrian Arab Republic); Al-Hawat, Sh.; Akel, M. [Physics Department, Atomic Energy Commission of Syria, P.O. Box 6091, Damascus (Syrian Arab Republic); Mrad, O. [Chemistry Department, Atomic Energy Commission of Syria, P.O. Box 6091, Damascus (Syrian Arab Republic)

    2015-02-14

    A new method for producing thin layer of bismuth nanospheres based on the use of low energy plasma focus device is demonstrated. Various techniques such as scanning electron microscopy, Rutherford backscattering spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and Raman spectroscopy have been used to characterize the morphology and the composition of the nanospheres. Experimental parameters may be adjusted to favour the formation of bismuth nanospheres instead of microspheres. Therefore, the formation of large surface of homogeneous layer of bismuth nanospheres with sizes of below 100 nm can be obtained. The natural snowball phenomenon is observed to be reproduced in nanoscale where spheres roll over the small nanospheres and grow up to bigger sizes that can reach micro dimensions. The comet-like structure, a reverse phenomenon to snowball is also observed.

  5. Inexpensive laser-induced surface modification in bismuth thin films

    Energy Technology Data Exchange (ETDEWEB)

    Contreras, A. Reyes [Facultad de Ciencias, Universidad Autónoma del Estado de México, Carretera Toluca, Ixtlahuaca Kilómetro 15.5, C.P. 50200 Edo. de México (Mexico); Hautefeuille, M., E-mail: mathieu_h@ciencias.unam.mx [Facultad de Ciencias, Universidad Nacional Autónoma de México, Avenida Universidad 3000, Circuito Exterior S/N, Coyoacán, Ciudad Universitaria, C.P. 04510 D.F. Mexico (Mexico); García, A. Esparza [Fotofísica y Películas Delgadas, Departamento de Tecnociencias, CCADET-UNAM, Circuito exterior s/n C.P. 04510 Cd. Universitaria, D.F. Mexico (Mexico); Mejia, O. Olea [Centro Conjunto de Investigación en Química Sustentable UAEM-UNAM, Carretera Toluca-Atlacomulco, Km 14.5, Unidad El Rosedal, 50200 San Cayetano, Estado de México (Mexico); López, M.A. Camacho [Facultad de Química, Universidad Autónoma del Estado de México, Tollocan s/n, esq. Paseo Colón, Toluca, Estado de México 50110 (Mexico)

    2015-05-01

    Highlights: • Laser-induced microbumps were formed on bismuth films using a simple, low-cost, laser setup. • The patterns, similar to those typically obtained with high-power lasers, were characterized. • Control of laser ablation conditions is critical in the fabrication of surface microbumps. - Abstract: In this work, we present results on texturing a 500 nm thick bismuth film, deposited by sputtering onto a glass slide using a low-cost homemade, near-infrared pulsed laser platform. A 785 nm laser diode of a CD–DVD pickup head was precisely focused on the sample mounted on a motorized two-axis translation stage to generate localized surface microbumps on the bismuth films. This simple method successfully transferred desired micropatterns on the films in a computer-numerical control fashion. Irradiated zones were characterized by atomic force microscopy and scanning electron microscopy. It was observed that final results are strongly dependent on irradiation parameters.

  6. Characterization of bismuth nanospheres deposited by plasma focus device

    International Nuclear Information System (INIS)

    Ahmad, M.; Al-Hawat, Sh.; Akel, M.; Mrad, O.

    2015-01-01

    A new method for producing thin layer of bismuth nanospheres based on the use of low energy plasma focus device is demonstrated. Various techniques such as scanning electron microscopy, Rutherford backscattering spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and Raman spectroscopy have been used to characterize the morphology and the composition of the nanospheres. Experimental parameters may be adjusted to favour the formation of bismuth nanospheres instead of microspheres. Therefore, the formation of large surface of homogeneous layer of bismuth nanospheres with sizes of below 100 nm can be obtained. The natural snowball phenomenon is observed to be reproduced in nanoscale where spheres roll over the small nanospheres and grow up to bigger sizes that can reach micro dimensions. The comet-like structure, a reverse phenomenon to snowball is also observed

  7. Analysis of 210Pb and 210Po concentrations in surface air by an α spectrometric method

    International Nuclear Information System (INIS)

    Winkler, R.; Hoetzl, H.; Chatterjee, B.

    1981-01-01

    A method is presented for determining the concentrations of airborne 210 Pb and 210 Po. The method employs α spectrometry to measure the count rate of 210 Po present on an electrostatic filter sample at two post-sampling times. The individual air concentrations of 210 Po and 210 Pb can be calculated from equations given. Sensitivity of the procedure is about 0.2 fCi 210 Po per m 3 of air. The method was applied to the study of long-term variations and frequency distributions of 210 Po and 210 Pb concentrations in surface air at a nonpolluted location about 10 km outside of Munich, F.R.G., from 1976 through 1979. During this period the average concentration levels were found to be 14.2 fCi 210 Pb per m 3 of air and 0.77 fCi 210 Po per m 3 of air, respectively. (author)

  8. The ratio of lead-210 to polonium-210 in U.K. diet.

    Science.gov (United States)

    Smith-Briggs, J L; Bradley, E J; Potter, M D

    1986-10-01

    The levels of the natural radionuclides, 210Pb and 210Po, in U.K. diet have been measured previously. However, in the earlier measurements, the samples were sufficiently aged for 210Pb and 210Po to have attained secular equilibrium. In order to determine the extent of disequilibrium between these radionuclides in fresh food, measurements have been made on recently collected dietary samples. Disequilibrium has been observed in five food groups. The activity per unit mass of 210Pb was found to be greater than that of 210Po in bread, cereals, sugar and preserves, whereas the opposite was found to be true for eggs and beverages. When account is taken of consumption rates, however, the total intakes of 210Pb and 210Po from these food groups are approximately the same. The annual effective dose equivalents from the ingestion of 210Pb and 210Po have been re-estimated at 41 and 12 mu Sv, respectively.

  9. An evaluation of the exposure to 210Pb-210Po in italian population

    International Nuclear Information System (INIS)

    Clemente, G.F.; Santori, G.; Renzetti, A.

    1979-01-01

    Following an introduction on the behaviour in the environment and in man of 210 Pb- 210 Po, experimental data are reported on 210 Pb- 210 Po exposure of the italian population. The analytical methods used to measure 210 Pb- 210 Po activity in the many biological and environmental samples analyzed are also reported. The data collected refer to the intake, excretion, internal burden and metabolism both in a group of subjects representative of the general population and in other critical groups exposed to high internal contamination of 210 Pb- 210 Po, as the radioactive spa wopkes and the miners. The absorbed dose due to 210 Pb- 210 Po has also been evaluated, on the basis of data referring to the various population groups

  10. Biological implications and clinical value of mir-210 in gastrointestinal cancer.

    Science.gov (United States)

    Yang, Wanli; Ma, Jiaojiao; Zhou, Wei; Zhou, Xin; Cao, Bo; Fan, Daiming; Hong, Liu

    2017-06-01

    Hypoxia, a common feature of tumor microenvironment, is known to accelerate tumor development and growth by promoting the formation of a neoplastic environment. Recent studies have provided a wealth of evidence that miRNAs are significant members of the adaptive response to low oxygen in tumors. miR-210 is one of the hypoxia-induced miRNAs, which has been reported extensively in cancer researches. However, there is no systematic discussion about the role of miR-210 in gastrointestinal cancer. We conducted a literature research in database including PubMed, Elsevier Science Direct and Medline before 16 September 2016, in order to collect articles of miR-210 in gastrointestinal cancer. Areas covered: In the present review, we mainly discuss the following aspects: hypoxia-induced dysregulation of miR-210, the expression of miR-210 and tumorigenesis, the resultant changes of miR-210 targets and its roles in different types of gastrointestinal cancer progression, the diagnostic, therapeutic and prognostic value of miR-210 in gastrointestinal cancer. Expert commentary: Numerous researches have demonstrated the values of miR-210 in cancer diagnosis, prognosis and targeted therapies, especially in gastrointestinal cancers. However, there are also some existing problems and challenges in translating the new research findings into clinical utility. Further investigations and studies are still urgently required.

  11. Accumulation of 210Po in Baltic invertebrates

    International Nuclear Information System (INIS)

    Skwarzec, B.; Falkowski, L.

    1988-01-01

    This paper presents the results of an investigation of the 210 Po contents of Baltic marine invertebrates. The 210 Po concentrations fall within the range 11.3-78.9 Bq kg -1 (dry wt), the higher values relating to polychaeta, priapulida and malacostraca and the lower levels to bivalvia. It is demonstrated that 210 Po is non-uniformly distributed within the isopod Mesidotea entomon and the bivalve Mya arenaria. The 210 Po contents of the internal organs decreasing in the order-hepatopancreas > alimentary tract > gill > muscle. Moreover, the results indicate the dominant role of the digestive organs of these invertebrates in controlling absorption and elimination of 210 Po. (author)

  12. MES lead bismuth forced circulation loop and test results

    International Nuclear Information System (INIS)

    Ono, Mikinori; Mine, Tatsuya; Kitano, Teruaki; Kamata, Kin-ya

    2003-01-01

    Liquid lead-bismuth is a promising material as future reactor coolant or intensive neutron source material for accelerator driven system (ADS). Mitsui Engineering and Shipbuilding Co., Ltd. (MES) completed lead-bismuth coolant (LBC) forced circulation loop in May 2001 and acquired engineering data on economizer, electro magnetic pump, electro magnetic flow meter and so on. For quality control of LBC, oxygen sensor and filtering element are developing using some hydrogen and moisture mixed gases. Structural materials corrosion test for accelerator driver system (ADS) will start soon. And thermal hydraulic test for ADS will start in tree years. (author)

  13. Hydrolysis studies on bismuth nitrate: synthesis and crystallization of four novel polynuclear basic bismuth nitrates.

    Science.gov (United States)

    Miersch, L; Rüffer, T; Schlesinger, M; Lang, H; Mehring, M

    2012-09-03

    Hydrolysis of Bi(NO(3))(3) in aqueous solution gave crystals of the novel compounds [Bi(6)O(4)(OH)(4)(NO(3))(5)(H(2)O)](NO(3)) (1) and [Bi(6)O(4)(OH)(4)(NO(3))(6)(H(2)O)(2)]·H(2)O (2) among the series of hexanuclear bismuth oxido nitrates. Compounds 1 and 2 both crystallize in the monoclinic space group P2(1)/n but show significant differences in their lattice parameters: 1, a = 9.2516(6) Å, b = 13.4298(9) Å, c = 17.8471(14) Å, β = 94.531(6)°, V = 2210.5(3) Å(3); 2, a = 9.0149(3) Å, b = 16.9298(4) Å, c = 15.6864(4) Å, β = 90.129(3)°, V = 2394.06(12) Å(3). Variation of the conditions for partial hydrolysis of Bi(NO(3))(3) gave bismuth oxido nitrates of even higher nuclearity, [{Bi(38)O(45)(NO(3))(24)(DMSO)(26)}·4DMSO][{Bi(38)O(45)(NO(3))(24)(DMSO)(24)}·4DMSO] (3) and [{Bi(38)O(45)(NO(3))(24)(DMSO)(26)}·2DMSO][{Bi(38)O(45)(NO(3))(24)(DMSO)(24)}·0.5DMSO] (5), upon crystallization from DMSO. Bismuth oxido clusters 3 and 5 crystallize in the triclinic space group P1 both with two crystallographically independent molecules in the asymmetric unit. The following lattice parameters are observed: 3, a = 20.3804(10) Å, b = 20.3871(9) Å, c = 34.9715(15) Å, α = 76.657(4)°, β = 73.479(4)°, γ = 60.228(5)°, V = 12021.7(9) Å(3); 5, a = 20.0329(4) Å, b = 20.0601(4) Å, c = 34.3532(6) Å, α = 90.196(1)°, β = 91.344(2)°, γ = 119.370(2)°, V = 12025.8(4) Å(3). Differences in the number of DMSO molecules (coordinated and noncoordinated) and ligand (nitrate, DMSO) coordination modes are observed.

  14. 210Pb and 210Po in tobacco - with a special focus on estimating the doses of 210Po to man

    International Nuclear Information System (INIS)

    Takizawa, Y.; Zhang, L.; Zhao, L.

    1994-01-01

    Inhalation of tobacco smoke is ranked second to food as a source of 210 Pb and 210 Po exposure to man. assay of 210 Pb and 210 Po in commercially available tobacco collected from many countries have been carried out to assess the potential risk from 210 Po present in tobacco. The range of 210 Po contained in the tobacco grands varied from 10.08 to 15.0 mBq/tob or 13.0 to 20.1 mBq/g and the mean was 11.6 mBq/tob or 15.4 mBq/g. During the International Standard Smoking process about 50% of 210 Po present in tobaccos was transferred into the smoke and the other 50% remained in the ash and butt. About 10% of the total 210 Po of tobacco was inhaled by smoke through mainstream smoke. One pack-a-day smoker inhaled 24 mBq of 210 Po per day through smoking and the annual inhalation was 8.8 Bq. The risk of mortality from lung cancer caused by 210 Po in tobaccos was 18 per million persons for the above model. (author) 6 refs.; 1 fig.; 4 tabs

  15. Bismuth oxyfluoride @ CMK-3 nanocomposite as cathode for lithium ion batteries

    Science.gov (United States)

    Ni, Dan; Sun, Wang; Xie, Liqiang; Fan, Qinghua; Wang, Zhenhua; Sun, Kening

    2018-01-01

    Bismuth oxyfluoride impregnated CMK-3 nanocomposite is synthesized by a facile nanocasting approach. Mesoporous carbon CMK-3 can suppress the aggregation and growth of bismuth oxyfluoride particles and offer rapid electron and Li ion passageways. Bismuth oxyfluoride nanoparticles are embedded in the mesoporous channels with particle size less than 20 nm. The bismuth oxyfluoride@CMK-3 nanocomposite maintains 148 mA h g-1 after 40 cycles with the capacity from both the bismuth oxyfluoride and the functional groups on the mesoporous carbon. The hybrid with confined bismuth oxyfluoride nanoparticles, conductive carbon network, and oxygen functional groups on the carbon matrix exhibits higher capacity and cycling stability than bulk bismuth oxyfluoride particles when used as lithium ion batteries cathode.

  16. Temperature gradient compatibility tests of some refractory metals and alloys in bismuth and bismuth--lithium solutions

    International Nuclear Information System (INIS)

    DiStefano, J.R.; Cavin, O.B.

    1976-11-01

    Quartz, T-111, and Mo thermal-convection loop tests were conducted at temperatures up to 700 0 C (100 0 C ΔT) to determine the compatibility of several refractory metals/alloys with bismuth and bismuth-lithium solutions for molten salt breeder reactor applications. Methods of evaluation included weight change measurements, metallographic examination, chemical and electron microprobe analysis, and mechanical properties tests. Molybdenum, T-111, and TA--10 percent W appear to be the most promising containment materials, while niobium and iron-based alloys are unacceptable

  17. Functionalized bismuth ferrite harmonic nanoparticles for cancer cells labeling and imaging

    Energy Technology Data Exchange (ETDEWEB)

    Passemard, Solène; Staedler, Davide; Sonego, Giona [Ecole Polytechnique Fédérale de Lausanne, Institute of Chemical Sciences and Engineering (Switzerland); Magouroux, Thibaud [Université de Genève, GAP-Biophotonics (Switzerland); Schneiter, Guillaume Stéphane [Ecole Polytechnique Fédérale de Lausanne, Institute of Chemical Sciences and Engineering (Switzerland); Juillerat-Jeanneret, Lucienne [University Institute of Pathology, CHUV-UNIL (Switzerland); Bonacina, Luigi [Université de Genève, GAP-Biophotonics (Switzerland); Gerber-Lemaire, Sandrine, E-mail: Sandrine.Gerber@epfl.ch [Ecole Polytechnique Fédérale de Lausanne, Institute of Chemical Sciences and Engineering (Switzerland)

    2015-10-15

    Bismuth ferrite (BFO) harmonic nanoparticles (NPs) display high nonlinear optical efficiency and excellent biocompatibility profile which make them attractive for the development of diagnostic applications as contrast agents. In this study, we present a general method for the functionalization of this material with chemical ligands targeting cancer molecular biomarkers. In particular, a conjugation protocol based on click reaction between alkynyl-containing targeting ligands and poly(ethylene glycol)-coated BFO NPs (67.7 nm) displaying surface reactive azido groups was developed. Copper-free click reaction allowed fast and efficient conjugation of a covalent inhibitor of prolyl-specific endopeptidases to coated BFO NPs. The ability of these functionalized nanomaterials (134.2 nm) to act as imaging probes for cancer cells was demonstrated by the selective labeling of human lung cancer cells.

  18. Metallothionein bioconjugates as delivery vehicles for bismuth-212 alpha particle therapy

    International Nuclear Information System (INIS)

    Macklis, R.M.; Morris, C.; Humm, J.; Hines, J.; Atcher, R.

    1991-01-01

    Metallothioneins (MTHs) are small cysteine-rich polypeptides that binds cationic metals at physiologic pH ranges through noncovalent -SH ligand interactions. Some leucine-rich renal MTHs have a particular avidity for bismuth. The authors have examined the ability of MTHs to selectively incorporate Bi-212, a short-lived high-energy alpha particle emitter currently under exploration as a potential therapeutic radiolabel for use in molecularly targeted cancer therapy. They find that under physiologic conditions, MTH will selectively incorporate Bi-212 after incubation with an equilibrium mixture of its upstream and downstream parents. The MTH moieties may be linked to tumor-binding macromolecules such as antibodies via thiolation reactions using SPDP, and the resultant Bismuth-avid molecules may be used either as primary delivery vehicles for the Bi-212 or as part of a 2-step release-and-catch isotope localization system in which the MTH-antibody conjugate is pre-localized at the tumor site and the radiometal is then administered and chelated in situ. They present the chemistry, dosimetry and potential clinical applications of this system

  19. Parameters promoting liquid metal embrittlement of the T91 steel in lead-bismuth eutectic alloy

    International Nuclear Information System (INIS)

    Proriol Serre, I.; Ye, C.; Vogt, J.B.

    2015-01-01

    The use of liquid lead-bismuth eutectic (LBE) as a spallation target and a coolant in accelerator-driven systems raises the question of the reliability of structural materials, such as T91 martensitic steel in terms of liquid metal assisted damage and corrosion. In this study, the mechanical behaviour of the T91 martensitic steel was examined in liquid lead-bismuth eutectic (LBE) and in inert atmosphere. Several conditions showed the most sensitive embrittlement factor. The Small Punch Test technique was employed using smooth specimens. In this standard heat treatment, T91 appeared in general as a ductile material, and became brittle in the considered conditions if the test was performed in LBE. It turns out that the loading rate appeared as a critical parameter for the occurrence of liquid metal embrittlement (LME) of the T91 steel in LBE. Loading the T91 very slowly instead of rapidly in oxygen saturated LBE resulted in brittle fracture. Furthermore, low-oxygen content in LBE and an increase in temperature promote LME. (authors)

  20. Neutronics design for lead-bismuth cooled accelerator-driven system for transmutation of minor actinide

    International Nuclear Information System (INIS)

    Tsujimoto, Kazufumi; Sasa, Toshinobu; Nishihara, Kenji; Oigawa, Hiroyuki; Takano, Hideki

    2004-01-01

    Neutronics design study was performed for lead-bismuth cooled accelerator-driven system (ADS) to transmute minor actinides. Early study for ADS indicated two problems: a large burnup reactivity swing and a significant peaking factor. To solve these problems, effect of design parameters on neutronics characteristics were searched. The design parameters were initial plutonium loading, buffer region between spallation target and core, and zone fuel loading. Parametric survey calculations were performed considering fuel cycle consisting of burnup and recycle. The results showed that burnup reactivity swing depends on the plutonium fraction in the initial fuel loading, and the lead-bismuth buffer region and the two-zone loading were effective for solving the problems. Moreover, an optimum value for the effective multiplication factor was also evaluated using reactivity coefficients. From the result, the maximum allowable value of the effective multiplication factor for a practical ADS can be set at 0.97. Consequently, a new core concept combining the buffer region and the two-zone loading was proposed base on the results of the parametric survey. (author)

  1. 226Ra, 210Pb and 210Po disequilibria in the western North Pacific

    International Nuclear Information System (INIS)

    Nozaki, Y.; Isunogai, S.

    1976-01-01

    226 Ra, 210 Pb and 210 Po were measured in oceanic profiles at two stations near the Bonin and Kurile trenches. 210 Po is depleted by 50% on average relative to 210 Pb in the surface water. In the deep water, 210 Pb is about 25% deficient relative to 226 Ra. Based on the deficiency, 210 Pb residence time with respect to removal by particulate matter was estimated to be less than 96 years in the deep water. 210 Pb deficiency in the bottom water was significantly greater than that of the adjacent deep water, indicating more effective removal near or at the bottom interface. 210 Pb, 210 Po and Th appear to have similar overall rate constants of particulate removal throughout the water column. (Auth.)

  2. Intake of lead210 and polonium210 by inhalation of atmospheric air and cigarette smoke

    International Nuclear Information System (INIS)

    Brigido Flores, Osvaldo; Montalvan Estrada, Adelmo; Alonso Hernandez, Carlos; Tomas Zerquera, Juan

    2004-01-01

    The electroplating of polonium at two different times onto copper disks and further measurement of alpha activity was the method used for 210Po determination in atmospheric air and tobacco products. The Polonium daughter is used to determine both the 210 Pb and 210 Po using the Bateman equations for radioactive growth and decay. The values of 210 Pb and 210 Po measured in the ground-level air reported average concentrations of 0.65 and 0.06 mBq.m-3, respectively. A cigarette contains an average activity of 13.0 mBq of 210 Pb and 10.4 mBq of 210 Po for different Cuban cigarette brands. The weighted-average annual effective dose estimated due to inhalation of these nuclides was computed to be 38 Sv, corresponding to the 26.8% of the total effective dose received by intake of 210 Pb and 210 Po in area of natural radioactive background

  3. Exposure of cuban population due to dietary intake of lead 210 and polonium 210

    International Nuclear Information System (INIS)

    Brigido Flores, O.; Barreras Caballero, A.; Montalvan Estrada, A.; Alonso Hernandez, C.; Tomas Zerquera, J.

    2000-01-01

    Data are presented on the concentrations of 210Pb and 210Po in potable water and different food items collected from various locations in Cuba. The electroplating of polonium at two different times onto copper disks and further measurement of alpha activity was the method used for 210Po determination in foods and water. The Polonium daughter is used to determine both the 210Pb and 210Po using the Bateman equations for radioactive growth and decay. The average 210Pb and 210Po concentration in potable water was 3 and 2 mBq.l-1, respectively and concentration in total diet averaged 47.7 mBq.kg-1 for 210Pb and 131.9 mBq.kg-1 for 210Po. The annual effective dose estimated due to ingestion of these nuclides contained in foods and potable water reported a value of 77.7 [Sv corresponding the 95.7 % to the food consuming

  4. 210Po and 210Pb in a pelagic trophic chain

    International Nuclear Information System (INIS)

    Radakovitch, O.; Strady, E.; Veron, A.; Chiffoleau, J.F.; Tronczynski, J.; Harmelin-Vivien, M.

    2013-01-01

    The ANR-COSTAS program studied the bioaccumulation and biomagnification of organic and inorganic contaminants through the trophic chains of two small pelagic fish, anchovy and sardine, on the continental shelf of the Gulf of Lion (Northwestern Mediterranean Sea). 210 Po and 210 Pb were analysed at various levels of this trophic chain, as well as trace metal elements, lead isotopes and C and N isotopes which provide additional information on both biogeochemical cycles and trophic transfer. To our knowledge, this is the first time that an entire trophic chain is analysed for these two radionuclides. Water, suspended particles, phytoplankton and zooplankton were collected at 7 stations during two contrast seasons. Phyto and zooplankton were separated in 6 classes through size-sieving: 6-60 μm; 60-200; 200-500; 500-1000; 1000-2000 and > 2000 μm. Anchovy and sardine were collected also two times and analyses were performed on muscle and liver independently for both sexes

  5. Optical properties of Dy3+ doped bismuth boro-tellurite glasses for WLED applications

    Science.gov (United States)

    Karthikeyan, P.; Marimuthu, K.

    2016-05-01

    The Dy3+ doped bismuth boro-tellurite glasses with the chemical composition (79.5-x) B2O3+xTeO2+10Bi2O3+10PbF2+0.5Dy2O3 (where x = 10, 20, 30 and 40 in wt%) have been prepared by melt quenching technique. The optical properties of the prepared glasses have been studied through absorption and emission spectral measurements. The bonding parameters, optical band gap energy, Urbach's energy and Judd-Ofelt (JO) intensity parameters (Ωλ, λ = 2, 4 and 6) were calculated from the absorption spectra. The radiative properties like transition probability (A), stimulated emission cross-section (σPE) and branching ratios (βR) were calculated from the emission spectra using JO theory. The strong emissions in the visible region, large stimulated emission cross-section and higher branching ratio values observed for the title glasses are found to be suitable for lasers and WLED applications.

  6. MicroRNA-210 contributes to preeclampsia by downregulating potassium channel modulatory factor 1.

    Science.gov (United States)

    Luo, Rongcan; Shao, Xuan; Xu, Peng; Liu, Yanlei; Wang, Yongqing; Zhao, Yangyu; Liu, Ming; Ji, Lei; Li, Yu-Xia; Chang, Cheng; Qiao, Jie; Peng, Chun; Wang, Yan-Ling

    2014-10-01

    Preeclampsia is a pregnancy-specific syndrome manifested by the onset of hypertension and proteinuria after the 20th week of gestation. Abnormal placenta development has been generally accepted as the initial cause of the disorder. Recently, microRNA-210 (miR-210) has been found to be upregulated in preeclamptic placentas compared with normal placentas, indicating a possible association of this small molecule with the placental pathology of preeclampsia. However, the function of miR-210 in the development of the placenta remains elusive. The aim of this study was to characterize the molecular mechanism of preeclampsia development by examining the role of miR-210. In this study, miR-210 and potassium channel modulatory factor 1 (KCMF1) expressions were compared in placentas from healthy pregnant individuals and patients with preeclampsia, and the role of miR-210 in trophoblast cell invasion via the downregulation of KCMF1 was investigated in the immortal trophoblast cell line HTR8/SVneo. The levels of KCMF1 were significantly lower in preeclamptic placenta tissues than in gestational week-matched normal placentas, which was inversely correlated with the level of miR-210. KCMF1 was validated as the direct target of miR-210 using real-time polymerase chain reaction, Western blotting, and dual luciferase assay in HTR8/SVneo cells. miR-210 inhibited the invasion of trophoblast cells, and this inhibition was abrogated by the overexpression of KCMF1. The inflammatory factor tumor necrosis factor-α could upregulate miR-210 while suppressing KCMF1 expression in HTR8/SVneo cells. This is the first report on the function of KCMF1 in human placental trophoblast cells, and the data indicate that aberrant miR-210 expression may contribute to the occurrence of preeclampsia by interfering with KCMF1-mediated signaling in the human placenta. © 2014 American Heart Association, Inc.

  7. Measured and evaluated neutron cross sections of elemental bismuth

    International Nuclear Information System (INIS)

    Smith, A.; Guenther, P.; Smith, D.; Whalen, J.; Howerton, R.

    1980-04-01

    Neutron total cross sections of elemental bismuth are measured with broad resolution from 1.2 to 4.5 MeV to accuracies of approx. = 1%. Neutron-differential-elastic-scattering cross sections of bismuth are measured from 1.5 to 4.0 MeV at incident neutron energy intervals of approx.< 0.2 MeV over the scattered-neutron angular range approx. = 20 to 160 deg. Differential neutron cross sections for the excitation of observed states in bismuth at 895 +- 12, 1606 +- 14, 2590 +- 15, 2762 +- 29, 3022 +- 21, and 3144 +- 15 keV are determined at incident neutron energies up to 4.0 MeV. An optical-statistical model is deduced from the measured values. This model, the present experimental results, and information available elsewhere in the literature are used to construct a comprehensive evaluated nuclear data file for elemental bismuth in the ENDF format. The evaluated file is particularly suited to the neutronic needs of the fusion-fission hybrid designer. 87 references, 10 figures, 6 tables

  8. The reduction of background signal in bismuth germanate scintillators

    International Nuclear Information System (INIS)

    Lewis, T.A.

    1986-07-01

    Bismuth germanate (BGO) is one of several new scintillator materials developed in recent years. It has similar energy resolution (6-8%) to sodium iodide (NaI) but it is non-hygroscopic, has a much better Peak-to-Compton ratio and a stopping power about 2.3 times greater than NaI. For counting activated foils it represents an improvement on NaI for high efficiency counting where the resolution of a germanium spectrometer is not required. Two scintillators bought for this purpose were found to have a higher than expected background signal between 500 keV and 2 MeV which was traced to Bi207, an active isotope of bismuth with a 38 year half-life and not listed as occurring naturally. Reference to the manufacturer showed all crystals to be similarly contaminated. It is speculated that this active isotope arises from cosmic proton activation of associated lead in the ore from which the bismuth is extracted. Although not confirmed rigorously it has been shown that bismuth extracted from ore with a low lead content does not contain Bi207. Scintillators have been manufactured from uncontaminated material and reductions in the background signal of more than an order of magnitude have been achieved. This reduction will be of immediate benefit for monitoring nickel foils (fast flux monitors) activated in zero-energy reactors and should also permit the exploitation of other low probability reactions previously not thought to be feasible. (author)

  9. Pairing from dynamically screened Coulomb repulsion in bismuth

    Science.gov (United States)

    Ruhman, Jonathan; Lee, Patrick A.

    2017-12-01

    Recently, Prakash et al. have discovered bulk superconductivity in single crystals of bismuth, which is a semimetal with extremely low carrier density. At such low density, we argue that conventional electron-phonon coupling is too weak to be responsible for the binding of electrons into Cooper pairs. We study a dynamically screened Coulomb interaction with effective attraction generated on the scale of the collective plasma modes. We model the electronic states in bismuth to include three Dirac pockets with high velocity and one hole pocket with a significantly smaller velocity. We find a weak-coupling instability, which is greatly enhanced by the presence of the hole pocket. Therefore we argue that bismuth is the first material to exhibit superconductivity driven by retardation effects of Coulomb repulsion alone. By using realistic parameters for bismuth we find that the acoustic plasma mode does not play the central role in pairing. We also discuss a matrix element effect, resulting from the Dirac nature of the conduction band, which may affect Tc in the s -wave channel without breaking time-reversal symmetry.

  10. Synthesis and structural characterization of Ce-doped bismuth titanate

    International Nuclear Information System (INIS)

    Pavlovic, Nikolina; Srdic, Vladimir V.

    2009-01-01

    Ce-modified bismuth titanate nanopowders Bi 4-x Ce x Ti 3 O 12 (x ≤ 1) have been synthesized using a coprecipitation method. DTA/TG, FTIR, XRD, SEM/EDS and BET methods were used in order to investigate the effect of Ce-substitution on the structure, morphology and sinterability of the obtained powders. The phase structure investigation revealed that after calcinations at 600 deg. C powder without Ce addition exhibited pure bismuth titanate phase; however, powders with Ce (x = 0.25, 0.5 and 0.75) had bismuth titanate pyrochlore phase as the second phase. The strongest effect of Ce addition on the structure was noted for the powder with the highest amount of Ce (x = 1) having a cubic pyrochlore structure. The presence of pure pyrochlore phase was explained by its stabilization due to the incorporation of cerium ions in titanate structure. Ce-modified bismuth titanate ceramic had a density over 95% of theoretical density and the fracture in transgranular manner most probably due to preferable distribution of Ce in boundary region

  11. Preparation of Ferroelectric Thin Films of Bismuth Layer Structured Compounds

    Science.gov (United States)

    Watanabe, Hitoshi; Mihara, Takashi; Yoshimori, Hiroyuki; Araujo, Carlos

    1995-09-01

    Ferroelectric thin films of bismuth layer structured compounds, SrBi2Ta2O9, SrBi2Nb2O9, SrBi4Ti4O15 and their solid solutions, were formed onto a sputtered platinum layer on a silicon substrate using spin-on technique and metal-organic decomposition (MOD) method. X-ray diffraction (XRD) analysis and some electrical measurements were performed on the prepared thin films. XRD results of SrBi2(Ta1- x, Nb x)2O9 films (0≤x≤1) showed that niobium ions substitute for tantalum ions in an arbitrary ratio without any change of the layer structure and lattice constants. Furthermore, XRD results of SrBi2 xTa2O9 films (0≤x≤1.5) indicated that the formation of the bismuth layer structure does not always require an accurate bismuth content. The layer structure was formed above 50% of the stoichiometric bismuth content in the general formula. SrBi2(Ta1- x, Nb x)2O9 films with various Ta/Nb ratios have large enough remanent polarization for nonvolatile memory application and have shown high fatigue resistance against 1011 cycles of full switching of the remanent polarization. Mixture films of the three compounds were also investigated.

  12. Ultrafast electron diffraction studies of optically excited thin bismuth films

    International Nuclear Information System (INIS)

    Rajkovic, Ivan

    2008-01-01

    This thesis contains work on the design and the realization of an experimental setup capable of providing sub-picosecond electron pulses for ultrafast electron diffraction experiments, and performing the study of ultrafast dynamics in bismuth after optical excitation using this setup. (orig.)

  13. Bismuth Ferrite for Active Control of Surface Plasmon Polariton Modes

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia; Zhukovsky, Sergei; Lavrinenko, Andrei

    2014-01-01

    We propose and investigate several layouts of m etal-insulator-metal waveguide with active core which can be utilized for dynamic switching in photonic integrated circuits. The active material, bismuth ferrite (BiFeO3), is sandwiched between metal plates and changes i ts refractive index through...

  14. Ultrafast electron diffraction studies of optically excited thin bismuth films

    Energy Technology Data Exchange (ETDEWEB)

    Rajkovic, Ivan

    2008-10-21

    This thesis contains work on the design and the realization of an experimental setup capable of providing sub-picosecond electron pulses for ultrafast electron diffraction experiments, and performing the study of ultrafast dynamics in bismuth after optical excitation using this setup. (orig.)

  15. Phase transition of bismuth telluride thin films grown by MBE

    DEFF Research Database (Denmark)

    Fülöp, Attila; Song, Yuxin; Charpentier, Sophie

    2014-01-01

    A previously unreported phase transition between Bi2Te3 and Bi4Te3 in bismuth telluride grown by molecular beam epitaxy is recorded via XRD, AFM, and SIMS observations. This transition is found to be related to the Te/Bi beam equivalent pressure (BEP) ratio. BEP ratios below 17 favor the formation...

  16. Behavior of 210Pb and 210Bi in soil-rice system and the effects of carrier-Pb

    International Nuclear Information System (INIS)

    Li Shuding

    1993-01-01

    Chemical species of 210 Pb and 210 Bi in soil and rice were investigated using 210 Pb trace experiment. 79%-91% of 210 Pb in the soil was in available fraction. On the contrary, 80%-98% of 210 Bi was bound. The available 210 Pb in the soil was changed slowly into bound fraction, while the bound 210 Bi transformed gradually into available one. Much of 210 Pb and 210 Bi entered into rice were as inorganic free ions. The bound 210 Pb in rice was less than 1% and the bound 210 Bi was around 40%. The different adsorption affinities between 210 Pb and 210 Bi were demonstrated by the different behavior of them. The effect of carrier-Pb on adsorption of 210 Pb and 210 Bi was also discussed

  17. Levels of {sup 210} Pb and {sup 210} Po in Brazilian cigarettes

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Pedro Lopes dos; Kelecom, Alphonse; Gouvea, Rita de Cassia dos Santos; Dutra, Iedo Ramos [Universidade Federal Fluminense, Niteroi, RJ (Brazil). Dept. de Biologia Geral

    1996-12-01

    {sup 210} Po and {sup 210} Pb concentrations have been determined in 18 Brazilian cigarette samples and compared with known data on U content. U is respectively 3-fold less and 4-fold less abundant than {sup 210} Po or {sup 210} Pb. No correlation could be observed between U concentration and those of Po or Pb. The mean concentration of {sup 210} Pb is higher than that of {sup 210} Pb observed in many other plants, even in plants frown in high background areas. (author) 19 refs., 1 fig., 1 tab.

  18. 210Po and 210Pb in Forest Soil and in Wild Berries in Finland

    International Nuclear Information System (INIS)

    Vaaramaa, Kaisa; Lehto, Jukka; Solatie, Dina; Aro, Lasse

    2008-01-01

    The behaviour of 210 Po and 210 Pb was investigated in forests in the Southern Finland site and in the Northern Finland site. Sampling sites were in Scots pine (Pinus sylvestris) forests. Maximum activities of 210 Po and 210 Pb in soil columns were found in organic layers. According to preliminary results of wild berry samples, the lowest 210 Po concentrations were found in berries. The highest concentration of 210 Po was found in stems of the blueberry (Vaccinium myrtillus) and the lingonberry (Vaccinium vitis-idaea) samples

  19. Contribution to the study of polonium-210 and lead-210 in marine organisms and their environment

    International Nuclear Information System (INIS)

    Heyraud, M.

    1982-06-01

    The following topics were emphasized: the role of 210 Po as a major source of natural radiation dose received by marin organisms; the contribution of 210 Po to the total α radioactivity in the hepatopancreas of crustaceans or mollusc cephalopods is more than 95%; in the euphausiid Meganyctiphanes norvegica, the main source of 210 Po is the food they consume; the possible use of 210 Po as a natural biological tracer of the feeding of deep-sea mesopelagic animals; the 210 Po/ 210 Pb ratio is a good indicator of the importance of biological processes in the marine environment [fr

  20. Content of [sup 210]Pb and [sup 210]Po in main foods of Hunan province

    Energy Technology Data Exchange (ETDEWEB)

    Jiaquan, Yan [Hunan Inst. for Labour Hygiene, Propylaxis and Treatment of Occupational Diseases (China); Radiological Health Group collabrated

    1992-03-01

    Investigation results were reported of content of [sup 210]Pb and [sup 210]Po in main foods of Hunan province from 1988 to early 1989. The content of [sup 210]Pb and [sup 210]Po in 17 kinds of foods investigated ranges from 0.02 to 11.8 Bqkg[sup -1] and from 0.04 to 15.6 Bqkg[sup -1] respectively. The estimated committed dose equivalents of residents were 102.6 [mu]Sv and 29.6 [mu]Sv for [sup 210]Pb and [sup 210]Po taken through foods respectively.

  1. Is ecological food also radioecological? - 210Po and 210Pb studies.

    Science.gov (United States)

    Strumińska-Parulska, Dagmara; Olszewski, Grzegorz

    2018-01-01

    Presented are results of a study on accumulation of naturally occurring 210 Po and 210 Pb in ecological and conventional farming food products in Poland: fruits, vegetables and cereals. The main idea behind this research was to determine the activity concentrations of 210 Po and 210 Pb in ecological and commercial food as well as calculate and compare the effective dose (radiation) connected to different origin of analyzed food products consumption. The studies showed the majority of all compared food samples contained similar 210 Po and 210 Pb activities and statistically, the consumption of organic and commercial food would give similar annual effective dose. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Content of 210Pb and 210Po in main foods of Hunan province

    International Nuclear Information System (INIS)

    Yan Jiaquan

    1992-01-01

    Investigation results were reported of content of 210 Pb and 210 Po in main foods of Hunan province from 1988 to early 1989. The content of 210 Pb and 210 Po in 17 kinds of foods investigated ranges from 0.02 to 11.8 Bqkg -1 and from 0.04 to 15.6 Bqkg -1 respectively. The estimated committed dose equivalents of residents were 102.6 μSv and 29.6 μSv for 210 Pb and 210 Po taken through foods respectively

  3. Separation of 210 Pb, 210 Bi and 210 Po by ion exchange and their liquid scintillation standardization

    International Nuclear Information System (INIS)

    Rodriguez, L.; Jimenez, A.; Grau, A.

    1996-01-01

    We applied the CIEMAT/NIST method and alpha/beta discrimination to ''210 Pb samples in equilibrium with its daughters, by preparing homogeneous and gel samples. The stability of samples was tested in different available cocktails, HiSafe''tm II, HiSafe''tmIII, Ultima-Gold''tm, Ultima-Gold''tmXR, Ultima-Gold''tmAB, Insta-Gel and e Insta-Gel II. Also we analyzed the disequilibrium of the radioactive chain ''210Pb+''210Bi+''210Po, achieving and excellent agreement between the results of the spectrum unfolding method and the experimental values. (Author) 13 refs

  4. Separation of 210Pb, 210Bi and 210Po by ion exchange and their Iiquid scintillation standardization

    International Nuclear Information System (INIS)

    Rodriguez, L.; Jimenez, A.; Grau, A.

    1996-01-01

    We applied the CIEMAT/NIST method and alpha/beta discrimination to ''210Pb samples in equilibrium with its daughters, by preparing homogeneous and gel samples. The stability of samples was tested in different available cocktails, HiSafe''TM II, HiSafe''TM III, Ultima-Gold''TM, Ultima-Gold''TM XR, Ultima-Gold''TM AB, Insta-Gel''R and e Insta-Gel''R lI. Also we analyzed the disequilibrium of the radioactive chain 210Pb+210Bi+210Po, achieving an excellent agreement between the results of the spectrum unfolding method and the experimental values. (Author) 13 refs

  5. AB initio energetics of lanthanum substitution in ferroelectric bismuth titanate

    International Nuclear Information System (INIS)

    Shah, S.H.

    2012-01-01

    Density functional theory based electronic structure calculations play a vital role in understanding, controlling and optimizing physical properties of materials at microscopic level. In present study system of interest is bismuth titanate (Bi/sub 4/Ti/sub 3/O/sub 12/)/(BIT) which has wide range of applications such as a high temperature piezoelectric and one of the best material for memory devices. However, it also suffers from serious issues such as oxygen vacancies which degrade its performance as a memory element and piezoelectric material. In this context, the bulk and defect properties of orthorhombic bismuth titanate (Bi/sub 4/Ti/sub 3/O/sub 12/) and bismuth lanthanum titanate (Bi/sub 3.25/La/sub 0.75/Ti/sub 3/O/sub 12/)/(BLT, x=0.75) were investigated by using first principles calculations and atomistic thermodynamics. Heats of formation, valid chemical conditions for synthesis, lanthanum substitution energies and oxygen and bismuth vacancy formation energies were computed. The study improves understanding of how native point defects and substitutional impurities influence the ferroelectric properties of these layered perovskite materials. It was found that lanthanum incorporation could occur on either of the two distinct bismuth sites in the structure and that the effect of substitution is to increase the formation energy of nearby native oxygen vacancies. The results provide direct atomistic evidence over a range of chemical conditions for the suggestion that lanthanum incorporation reduces the oxygen vacancy concentration. Oxygen vacancies contribute to ferroelectric fatigue by interacting strongly with domain walls and therefore a decrease in their concentration is beneficial. (orig./A.B.)

  6. Efficient enhancement of bismuth NIR luminescence by aluminum and its mechanism in bismuth doped germanate laser glass

    DEFF Research Database (Denmark)

    Wang, L.P.; Tan, L.L.; Yue, Yuanzheng

    2016-01-01

    As a new member of laser glass family, bismuth-doped glasses have received rising interests due to the application of fiber amplifiers and laser sources in the new spectral range for the next-generation optical communication system. For practical application of the glasses, it must be considered ...

  7. Formation of gas-phase π-allyl radicals from propylene over bismuth oxide and γ-bismuth molybdate catalysts

    International Nuclear Information System (INIS)

    Martir, W.; Lunsford, J.H.

    1981-01-01

    Gas-phase π-allyl radicals were produced when propylene reacted over Bi 2 O 3 and γ-bismuth molybdate catalysts at 723 K. The pressure in the catalyst zone was varied between 5 x 10 -3 and 1 torr. The radicals were detected by EPR spectroscopy together with a matrix isolation technique in which argon was used as the diluent. The matrix was formed on a sapphire rod at 12 K which was located 33-cm downstream from the catalyst. Bismuth oxide was more effective in the production of gas-phase allyl radicals than γ-bismuth molybdate. By contrast α-bismuth molybdate was ineffective in forming allyl radicals and MoO 3 acted as a sink for radicals which were produced elsewhere in the system. Comparison of the π-allyl radical and the stable product concentrations over Bi 2 O 3 revealed that gas-phase radical recombination reactions served as a major pathway for the formation of 1,5-hexadiene. Addition of small amounts of gas-phase oxygen increased the concentration of allyl radicals, and at greater oxygen levels allyl peroxy radicals were detected. Because of the effect of temperature on the equilibrium between allyl and allyl peroxy radicals, the latter product must be formed in the cooler part of the system

  8. 210Pb ingestion in Akita City, Japan

    International Nuclear Information System (INIS)

    Hisamatsu, Shunichi; Takizawa, Yukio; Komura, Kazuhisa; Tada, Tetsuo.

    1992-01-01

    Ingestion of 210 Pb in Akita City, northern Japan was studied with food category samples and total diet samples by means of a low energy photon spectrometry. Results for food category samples revealed that the contribution of marine products to total 210 Pb ingestion was the largest. Mean 210 Pb ingestion of the two total diet samples was found to be 0.19 Bq d -1 , and approximately 1/3 of a previous reported value which was cited in an UNSCEAR report as an example of high 210 Pb ingestion by marine foods consumption. (author)

  9. Analysis of 210Pb and 210Po in Brazilian foods and diets

    International Nuclear Information System (INIS)

    Cunha, I.L.; Bueno, L.; Favaro, D.I.T.; Maihara, V.A.; Cozzollino, S.

    2001-01-01

    Radiochemical procedures for the analysis of 210 Pb and 210 Po in foods and diets are presented. Because of the low beta energy of 210 Pb, its analysis was based on a separation of the daughter radionuclide 210 Bi by precipitation of lead sulphate, 210 Bi ingrowing and beta counting of this nuclide. 210 Po analysis was based on wet dissolution of the sample, deposition onto silver disc and counting by alpha-spectrometry. Levels of these radionuclides in individual items and diets of selected university students were determined in order to evaluate the intakes of 210 Pb and 210 Po as well as the dose due to ingestion of foods and diets in Sao Paulo city. (author)

  10. Determination of 210Pb e 210Po in marine samples and aerosols

    International Nuclear Information System (INIS)

    Saito, Roberto Tatsuya

    1996-01-01

    In this work the methodologies for 210 Pb e 210 Po analyses in marine samples, such as fish, seaweed, sediment, and aerosol samples are presented. The 210 Pb levels in the samples were obtained by both 210 Bi and 210 Po ingrowth. The 210 Pb analysis via 210 Bi presents the following steps: 210 Pb leaching from samples with 8 M nitric acid and hydrogen peroxide; lead sulphate precipitation; conversion to carbonate; dissolution; lead sulphate precipitation; gravimetric analysis of lead; waiting of time to reach radioactive equilibrium and 210 Bi beta counting by employing a Geiger-Mueller detector with a low background radiation. The 210 Pb analysis via 210 Po presents the following steps: 210 Pb and 210 Po leaching from samples with 8 M nitric acid and hydrogen peroxide; nitric acid elimination by heating and hydrochloric acid addition; spontaneous deposition onto silver disc and alpha counting of polonium in silicon surface-barrier detector. In order to determine 210 Pb activity, the solution was percolated in the Dowex AG 1-X 8 anion exchange resin; preconditioned with 8 M nitric acid; the lead was eluted by 8 M hydrochloric acid; the solution was gently evaporated to dryness and diluted with 0.5 N hydrochloric acid. After 3-6 months a second 210 Po spontaneous deposition onto silver disc was carried out. The methodology for 210 Pb analysis via 210 Bi showed lead recoveries from 63 to 100%. In the method via 210 Po the polonium recoveries were varied from 39 to 63% under manual agitation, and from 60 to 100% under mechanical agitation. The radiochemical methods for 210 Po and 210 Pb analyses were applied in reference samples from International Atomic Energy Agency (IAEA) and the results obtained showed the good precision and accuracy of the established methods. The analysis of marine sediment samples of Antarctica presented 210 Pb and Po levels from 8 to 60 Bq.kg -1 , and fish samples from Sao Paulo Coast presented 210 Po levels from 0.5 to 5.3 Bq.kg -1 . These

  11. 17 CFR 210.9-01 - Application of §§ 210.9-01 to 210.9-07

    Science.gov (United States)

    2010-04-01

    ... COMMISSION FORM AND CONTENT OF AND REQUIREMENTS FOR FINANCIAL STATEMENTS, SECURITIES ACT OF 1933, SECURITIES....9-01 Application of §§ 210.9-01 to 210.9-07 This article is applicable to consolidated financial statements filed for bank holding companies and to any financial statements of banks that are included in...

  12. Geochemical behavior of 210Pb and 210Po in the nearshore waters off western Taiwan

    International Nuclear Information System (INIS)

    Wei, Ching-Ling; Lin, Shiao-Yu; Wen, Liang-Saw; Sheu, David D.-D.

    2012-01-01

    Highlights: ► 210 Pb and 210 Po in the nearshore waters were determined off western coast of Taiwan. ► Partitioning of the radionuclides in turbid waters was discussed. ► Removal flux of particulate organic carbon was quantified using 210 Po proxy. - Abstract: Dissolved and particulate 210 Pb and 210 Po were determined at 15 stations along the coastline off western Taiwan in April 2007. The 210 Pb activities in dissolved and particulate phases fell within a relatively small range of 2.4–5.2 dpm 100 L −1 and 1.0–3.2 dpm 100 L −1 , respectively. The dissolved and particulate 210 Po activities also fell within a small range of 0.8–3.4 dpm 100 L −1 and 1.1–2.9 dpm 100 L −1 , respectively. The correlation of the distribution coefficients (K d ) of 210 Pb and 210 Po with particle concentration in turbid waters are not as evident as in the open ocean. The mass balance calculation shows that the residence times of 210 Pb and 210 Po with respect to particle removal from the nearshore waters ranges from 3 to 15 days and from 14 to 125 days, respectively. The flux of particulate organic carbon was estimated by 210 Po proxy and ranged from 4.8 to 33.7 mmol-C m −2 d −1 .

  13. Target preparation

    International Nuclear Information System (INIS)

    Hinn, G.M.

    1984-01-01

    A few of the more interesting of the 210 targets prepared in the Laboratory last year are listed. In addition the author continues to use powdered silver mixed with /sup 9,10/BeO to produce sources for accelerator radio dating of Alaskan and South Polar snow. Currently, he is trying to increase production by multiple sample processing. Also the author routinely makes 3 μg/cm 2 cracked slacked carbon stripper foils and is continuing research with some degree of success in making enriched 28 Si targets starting with the oxide

  14. Bismuth-, Tin-, and Lead-Containing Metal-Organic Materials: Synthesis, Structure, Photoluminescence, Second Harmonic Generation, and Ferroelectric Properties

    Science.gov (United States)

    Wibowo, Arief Cahyo

    Metal-Organic Materials (MOMs) contain metal moieties and organic ligands that combine to form discrete (e.g. metal-organic polyhedra, spheres or nanoballs, metal-organic polygons) or polymeric structures with one-, two-, or three-dimensional periodicities that can exhibit a variety of properties resulting from the presence of the metal moieties and/or ligand connectors in the structure. To date, MOMs with a range of functional attributes have been prepared, including record-breaking porosity, catalytic properties, molecular magnetism, chemical separations and sensing ability, luminescence and NLO properties, multiferroic, ferroelectric, and switchable molecular dielectric properties. We are interested in synthesizing non-centrosymmetric MOM single crystals possessing one of the ten polar space groups required for non-linear optical properties (such as second harmonic generation) and ferroelectric applications. This thesis is divided into two main parts: materials with optical properties, such as photoluminescence and materials for targeted applications such as second harmonic generation and ferroelectric properties. This thesis starts with an introduction describing material having centrosymmetric, non-polar space groups, single crystals structures and their photoluminescence properties. These crystals exhibit very interesting and rare structures as well as interesting photoluminescence properties. Chapters 2-5 of this thesis focus on photoluminescent properties of new MOMs, and detail the exploratory research involving the comparatively rare bismuth, lead, and tin coordination polymers. Specifically, the formation of single white-light emitting phosphors based on the combination of bismuth or lead with pyridine-2,5-dicarboxylate is discussed (Chapter 2). The observation of a new Bi2O2 layer and a new Bi4O 3 chain in bismuth terephthalate-based coordination polymers is presented in Chapter 3, while the formation of diverse structures of tin-based coordination

  15. Polonium-210 and lead-210 in the terrestrial environment: a historical review.

    Science.gov (United States)

    Persson, Bertil R R; Holm, Elis

    2011-05-01

    The radionuclides (210)Po and (210)Pb widely present in the terrestrial environment are the final long-lived radionuclides in the decay of (238)U in the earth's crust. Their presence in the atmosphere is due to the decay of (222)Rn diffusing from the ground. The range of activity concentrations in ground level air for (210)Po is 0.03-0.3 Bq m(-3) and for (210)Pb 0.2-1.5 Bq m(-3). In drinking water from private wells the activity concentration of (210)Po is in the order of 7-48 mBq l(-1) and for (210)Pb around 11-40 mBq l(-1). From water works, however, the activity concentration for both (210)Po and (210)Pb is only in the order of 3 mBq l(-1). Mosses, lichens and peat have a high efficiency in capturing (210)Po and (210)Pb from atmospheric fallout and exhibit an inventory of both (210)Po and (210)Pb in the order of 0.5-5 kBq m(-2) in mosses and in lichens around 0.6 kBq m(-2). The activity concentrations in lichens lies around 250 Bq kg(-1), dry mass. Reindeer and caribou graze lichen which results in an activity concentration of (210)Po and (210)Pb of about 1-15 Bq kg(-1) in meat from these animals. The food chain lichen-reindeer or caribou, and Man constitutes a unique model for studying the uptake and retention of (210)Po and (210)Pb in humans. The effective annual dose due to (210)Po and (210)Pb in people with high consumption of reindeer/caribou meat is estimated to be around 260 and 132 μSv a(-1) respectively. In soils, (210)Po is adsorbed to clay and organic colloids and the activity concentration varies with soil type and also correlates with the amount of atmospheric precipitation. The average activity concentration levels of (210)Po in various soils are in the range of 20-240 Bq kg(-1). Plants become contaminated with radioactive nuclides both by absorption from the soil (supported Po) and by deposition of radioactive fallout on the plants directly (unsupported Po). In fresh leafy plants the level of (210)Po is particularly high as the result of the

  16. Polonium-210 and lead-210 in the terrestrial environment: a historical review

    International Nuclear Information System (INIS)

    Persson, Bertil R.R.; Holm, Elis

    2011-01-01

    The radionuclides 210 Po and 210 Pb widely present in the terrestrial environment are the final long-lived radionuclides in the decay of 238 U in the earth's crust. Their presence in the atmosphere is due to the decay of 222 Rn diffusing from the ground. The range of activity concentrations in ground level air for 210 Po is 0.03-0.3 Bq m -3 and for 210 Pb 0.2-1.5 Bq m -3 . In drinking water from private wells the activity concentration of 210 Po is in the order of 7-48 mBq l -1 and for 210 Pb around 11-40 mBq l -1 . From water works, however, the activity concentration for both 210 Po and 210 Pb is only in the order of 3 mBq l -1 . Mosses, lichens and peat have a high efficiency in capturing 210 Po and 210 Pb from atmospheric fallout and exhibit an inventory of both 210 Po and 210 Pb in the order of 0.5-5 kBq m -2 in mosses and in lichens around 0.6 kBq m -2 . The activity concentrations in lichens lies around 250 Bq kg -1 , dry mass. Reindeer and caribou graze lichen which results in an activity concentration of 210 Po and 210 Pb of about 1-15 Bq kg -1 in meat from these animals. The food chain lichen-reindeer or caribou, and Man constitutes a unique model for studying the uptake and retention of 210 Po and 210 Pb in humans. The effective annual dose due to 210 Po and 210 Pb in people with high consumption of reindeer/caribou meat is estimated to be around 260 and 132 μSv a -1 respectively. In soils, 210 Po is adsorbed to clay and organic colloids and the activity concentration varies with soil type and also correlates with the amount of atmospheric precipitation. The average activity concentration levels of 210 Po in various soils are in the range of 20-240 Bq kg -1 . Plants become contaminated with radioactive nuclides both by absorption from the soil (supported Po) and by deposition of radioactive fallout on the plants directly (unsupported Po). In fresh leafy plants the level of 210 Po is particularly high as the result of the direct deposition of 222 Rn

  17. Flow characteristics of natural circulation in a lead-bismuth eutectic loop

    Institute of Scientific and Technical Information of China (English)

    Chen-Chong Yue; Liu-Li Chen; Ke-Feng Lyu; Yang Li; Sheng Gao; Yue-Jing Liu; Qun-Ying Huang

    2017-01-01

    Lead and lead-alloys are proposed in future advanced nuclear system as coolant and spallation target.To test the natural circulation and gas-lift and obtain thermal-hydraulics data for computational fluid dynamics (CFD) and system code validation,a lead-bismuth eutectic rectangular loop,the KYLIN-Ⅱ Thermal Hydraulic natural circulation test loop,has been designed and constructed by the FDS team.In this paper,theoretical analysis on natural circulation thermal-hydraulic performance is described and the steady-state natural circulation experiment is performed.The results indicated that the natural circulation capability depends on the loop resistance and the temperature and center height differences between the hot and cold legs.The theoretical analysis results agree well with,while the CFD deviate from,the experimental results.

  18. Equilibrium evaporation test of lead-bismuth eutectic and of tellurium in lead-bismuth

    International Nuclear Information System (INIS)

    Ohno, Shuji; Nishimura, Masahiro; Hamada, Hirotsugu; Miyahara, Shinya; Sasa, Toshinobu; Kurata, Yuji

    2005-01-01

    A series of equilibrium evaporation experiment was performed to acquire the essential and the fundamental knowledge about the transfer behavior of lead-bismuth eutectic (LBE) and impurity tellurium in LBE from liquid to gas phase. The experiments were conducted using the transpiration method in which saturated vapor in an isothermal evaporation pot was transported by inert carrier gas and collected outside of the pot. The size of the used evaporation pot is 8 cm inner diameter and 15 cm length. The weight of the LBE pool in the pot is about 500 g. The investigated temperature range was 450degC to 750degC. From this experiment and discussion using the data in literature, we have obtained several instructive and useful data on the LBE evaporation behavior such as saturated vapor pressure of LBE, vapor concentration of Pb, Bi and Bi 2 in LBE saturated gas phase, and activity coefficient of Pb in the LBE. The LBE vapor pressure equation is represented as the sum of Pb, Bi and Bi 2 vapor in the temperature range between 550degC and 750degC as logP[Pa]=10.2-10100/T[k]. The gas-liquid equilibrium partition coefficient of tellurium in LBE is in the range of 10 to 100, with no remarkable temperature dependency between 450degC and 750degC. This research was founded by the Ministry of Education, Culture, Sports, Science and Technology (MEXT). (author)

  19. 22 CFR 210.650 - Grant.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Grant. 210.650 Section 210.650 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT GOVERNMENTWIDE REQUIREMENTS FOR DRUG-FREE WORKPLACE... to transfer a thing of value to the recipient to carry out a public purpose of support or stimulation...

  20. 12 CFR 19.210 - Scope.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Scope. 19.210 Section 19.210 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY RULES OF PRACTICE AND PROCEDURE Equal Access to... adjudicatory proceedings under this part are set forth at 31 CFR part 6. ...

  1. 31 CFR 560.210 - Exempt transactions.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Exempt transactions. 560.210 Section 560.210 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE OF... services to market, produce or co-produce, create or assist in the creation of information and...

  2. 31 CFR 537.210 - Exempt transactions.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Exempt transactions. 537.210 Section 537.210 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE OF... assist in the creation of information or informational materials; and, with respect to information or...

  3. Polonium-210 in food and tobacco

    Energy Technology Data Exchange (ETDEWEB)

    Ali, S K [Sudan Academy of Science, Atomic Energy Research Coordination Council, Khartoum (Sudan)

    2006-04-15

    The objective of this study is concerned with the radioactivity in food and tobacco, derived mainly from {sup 210}Po which contribute to the radiation dose received through diet and smoking. This subject was covered under four chapters. Chapter one deals with historical background of polonium-210 and its behavior in living system. Sources of polonium-210 in food and tobacco are explained in the second chapter. Relevant issues such as separation and measurement of polonium-210 covered in subsequent chapter. Chapter four reviewed recent studies on polonium-210. It was found that the main source of this radionuclide is the phosphatic fertilizers that used in food and tobacco cultivation. These fertilizers contain the decay products of {sup 238}U series of which {sup 210}Po is known to be very important from environmental point of view. Many studies conducted showed that the committed effective dose derived mainly from {sup 210} Po due to the consumption of food, particularly sea food is significant, furthermore {sup 210}Po in tobacco is known to be the main cause of many diseases such as lung cancer.(Author)

  4. 41 CFR 101-29.210 - Product.

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Product. 101-29.210... FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 29-FEDERAL PRODUCT DESCRIPTIONS 29.2-Definitions § 101-29.210 Product. The term product is any end item, either manufactured or produced, and also...

  5. 19 CFR 210.79 - Advisory opinions.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Advisory opinions. 210.79 Section 210.79 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE... of the Tariff Act of 1930, would be in the public interest, and would benefit consumers and...

  6. The determination of 210Po in urine

    International Nuclear Information System (INIS)

    Bale, W.F.; Helmkamp, R.W.; Hrynyszyn, V.; Contreras, M.A.

    1975-01-01

    To measure 210 Po present in normal human urine a technique was developed in which a 4.5 x 11cm silver foil was shaken at room temperature for 48-hr periods in each of two successive volumes of 1.7 l. of urine acidified to 0.5N with HCl. Alpha rays were counted with an ionization chamber, coupled to a vibrating reed electrometer, and capable of measuring α-ray pulses originating on both sides of the silver foil serving as a central electrode. The background α-count was less than 2/hr. Analyses of human urine spiked with 0.29 to 0.58pCi of 210 Po, together with studies of urine from dogs carrying significant body burdens of 210 Pb, indicated that the average recovery of added 210 Po from 1.7 l. volumes of spiked human urine was 72%. If it is assumed that the same percentage of 210 Po is extracted from non-spiked urine, then the average 210 Po concentration found in 13 analyses of 2 x 1.7 l. samples from 26 different pools of fresh human urine was 0.023pCi/l. Substantial additional 210 Po was generated on short aging of the urine through radioactive decay of excreted 210 Bi. (author)

  7. Polonium-210 in food and tobacco

    International Nuclear Information System (INIS)

    Ali, S.K.

    2006-04-01

    The objective of this study is concerned with the radioactivity in food and tobacco, derived mainly from 210 Po which contribute to the radiation dose received through diet and smoking. This subject was covered under four chapters. Chapter one deals with historical background of polonium-210 and its behavior in living system. Sources of polonium-210 in food and tobacco are explained in the second chapter. Relevant issues such as separation and measurement of polonium-210 covered in subsequent chapter. Chapter four reviewed recent studies on polonium-210. It was found that the main source of this radionuclide is the phosphatic fertilizers that used in food and tobacco cultivation. These fertilizers contain the decay products of 238 U series of which 210 Po is known to be very important from environmental point of view. Many studies conducted showed that the committed effective dose derived mainly from 210 Po due to the consumption of food, particularly sea food is significant, furthermore 210 Po in tobacco is known to be the main cause of many diseases such as lung cancer.(Author)

  8. 40 CFR 86.210-94 - [Reserved

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false [Reserved] 86.210-94 Section 86.210-94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF... Year Gasoline-Fueled New Light-Duty Vehicles, New Light-Duty Trucks and New Medium-Duty Passenger...

  9. 18 CFR 706.210 - Coercion.

    Science.gov (United States)

    2010-04-01

    ... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Coercion. 706.210 Section 706.210 Conservation of Power and Water Resources WATER RESOURCES COUNCIL EMPLOYEE... financial benefit to himself or another person, particularly one with whom he has family, business, or...

  10. 31 CFR 210.10 - RDFI liability.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false RDFI liability. 210.10 Section 210.10 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE, DEPARTMENT OF THE TREASURY FINANCIAL MANAGEMENT SERVICE FEDERAL GOVERNMENT PARTICIPATION IN THE AUTOMATED...

  11. 31 CFR 210.6 - Agencies.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Agencies. 210.6 Section 210.6 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE, DEPARTMENT OF THE TREASURY FINANCIAL MANAGEMENT SERVICE FEDERAL GOVERNMENT PARTICIPATION IN THE AUTOMATED...

  12. 31 CFR 210.3 - Governing law.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Governing law. 210.3 Section 210.3 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE, DEPARTMENT OF THE TREASURY FINANCIAL MANAGEMENT SERVICE FEDERAL GOVERNMENT PARTICIPATION IN THE AUTOMATED...

  13. 31 CFR 210.2 - Definitions.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Definitions. 210.2 Section 210.2 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE, DEPARTMENT OF THE TREASURY FINANCIAL MANAGEMENT SERVICE FEDERAL GOVERNMENT PARTICIPATION IN THE AUTOMATED...

  14. 31 CFR 210.11 - Limited liability.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Limited liability. 210.11 Section 210.11 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE, DEPARTMENT OF THE TREASURY FINANCIAL MANAGEMENT SERVICE FEDERAL GOVERNMENT PARTICIPATION IN THE AUTOMATED...

  15. 31 CFR 210.8 - Financial institutions.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Financial institutions. 210.8 Section... CLEARING HOUSE General § 210.8 Financial institutions. (a) Status as a Treasury depositary. The origination or receipt of an entry subject to this part does not render a financial institution a Treasury...

  16. 210Polonium and 210lead content of marine birds from Southeastern Brazil

    International Nuclear Information System (INIS)

    Godoy, José Marcus; Siciliano, Salvatore; Carvalho, Zenildo Lara de; Tavares, Davi C.; Fulgencio de Moura, Jaílson

    2014-01-01

    In this study, we report the 210 Po and 210 Pb concentrations of bone, muscle and liver samples that were obtained from twelve different marine bird species stranded on beaches in the central–north region of Rio de Janeiro State. Both radionuclides were highly concentrated in the liver samples; however, the lowest mean 210 Po/ 210 Pb activity ratio (1.3) was observed in bones compared with liver and muscle (16.8 and 13.8, respectively). Among the species that were studied, Fregata magnificens, with a diet based exclusively on fish, had the lowest 210 Pb and 210 Po concentrations and the lowest 210 Po/ 210 Pb activity ratio. The 210 Po concentrations in Puffinus spp. liver samples followed a log-normal distribution, with a geometric mean of 300 Bq kg -1 wet weight . Only two references pertaining to 210 Po in marine birds were found in a Web of Science search of the literature, and each study reported a different concentration value. The values determined in this experiment are consistent with those in one of the previous studies, which also included one of the species studied in this work. No values for 210 Pb in marine birds have been published previously. - Highlights: • 210 Po and 210 Pb were determined in muscle, liver and bone samples of marine birds. • For both radionuclides, the highest concentrations were observed on liver samples. • Only three previous publications on 210 Po in marine birds were found in the literature. • The obtained results represent the first one related to 210 Pb in marine birds

  17. Rapid semi-quantitative determination of bismuth in minerals using ascending paper chromatography (1961)

    International Nuclear Information System (INIS)

    Agrinier, H.

    1961-01-01

    The bismuth is separated by a solvent made up of acetone, water, and hydrofluoric and hydrochloric acids. The bismuth is developed with dimercapto-2.5 thio-diazole-1.3.4 and ammonium sulphide. The use of this method for the detection of bismuth in minerals makes it possible to determine the metal at a concentration of 5 x 10 -6 . (author) [fr

  18. Downregulation of miR-210 expression inhibits proliferation, induces apoptosis and enhances radiosensitivity in hypoxic human hepatoma cells in vitro

    International Nuclear Information System (INIS)

    Yang, Wei; Sun, Ting; Cao, Jianping; Liu, Fenju; Tian, Ye; Zhu, Wei

    2012-01-01

    Hypoxia is a common feature of solid tumors and an important contributor to tumor radioresistance. miR-210 is the most consistently and robustly induced microRNA under hypoxia in different types of tumor cells and normal cells. In the present study, to explore the feasibility of miR-210 as an effective therapeutic target, lentiviral-mediated anti-sense miR-210 gene transfer technique was employed to downregulate miR-210 expression in hypoxic human hepatoma SMMC-7721, HepG2 and HuH7 cells, and phenotypic changes of which were analyzed. Hypoxia led to an increased hypoxia inducible factor-1α (HIF-1α) and miR-210 expression and cell arrest in the G 0 /G 1 phase in all cell lines. miR-210 downregulation significantly suppressed cell viability, induced cell arrest in the G 0 /G 1 phase, increased apoptotic rate and enhanced radiosensitivity in hypoxic human hepatoma cells. Moreover, apoptosis-inducing factor, mitochondrion-associated, 3 (AIFM3) was identified as a direct target gene of miR-210. AIFM3 downregulation by siRNA attenuated radiation induced apoptosis in miR-210 downregulated hypoxic human hepatoma cells. Taken together, these data suggest that miR-210 might be a potential therapeutic target and specific inhibition of miR-210 expression in combination with radiotherapy might be expected to exert strong anti-tumor effect on hypoxic human hepatoma cells. -- Highlights: ► miR-210 downregulation radiosensitized hypoxic hepatoma. ► AIFM3 was identified as a direct target gene of miR-210. ► miR-210 might be a therapeutic target to hypoxic hepatoma.

  19. Downregulation of miR-210 expression inhibits proliferation, induces apoptosis and enhances radiosensitivity in hypoxic human hepatoma cells in vitro

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Wei, E-mail: detachedy@yahoo.com.cn [Department of Radiobiology, School of Radiological Medicine and Protection, Soochow University, Suzhou (China); Sun, Ting [Brain and Nerve Research Laboratory, The First Affiliated Hospital, Soochow University, Suzhou (China); Cao, Jianping; Liu, Fenju [Department of Radiobiology, School of Radiological Medicine and Protection, Soochow University, Suzhou (China); Tian, Ye [Department of Radiotherapy and Oncology, The Second Affiliated Hospital, Soochow University, Suzhou (China); Zhu, Wei [Department of Radiobiology, School of Radiological Medicine and Protection, Soochow University, Suzhou (China)

    2012-05-01

    Hypoxia is a common feature of solid tumors and an important contributor to tumor radioresistance. miR-210 is the most consistently and robustly induced microRNA under hypoxia in different types of tumor cells and normal cells. In the present study, to explore the feasibility of miR-210 as an effective therapeutic target, lentiviral-mediated anti-sense miR-210 gene transfer technique was employed to downregulate miR-210 expression in hypoxic human hepatoma SMMC-7721, HepG2 and HuH7 cells, and phenotypic changes of which were analyzed. Hypoxia led to an increased hypoxia inducible factor-1{alpha} (HIF-1{alpha}) and miR-210 expression and cell arrest in the G{sub 0}/G{sub 1} phase in all cell lines. miR-210 downregulation significantly suppressed cell viability, induced cell arrest in the G{sub 0}/G{sub 1} phase, increased apoptotic rate and enhanced radiosensitivity in hypoxic human hepatoma cells. Moreover, apoptosis-inducing factor, mitochondrion-associated, 3 (AIFM3) was identified as a direct target gene of miR-210. AIFM3 downregulation by siRNA attenuated radiation induced apoptosis in miR-210 downregulated hypoxic human hepatoma cells. Taken together, these data suggest that miR-210 might be a potential therapeutic target and specific inhibition of miR-210 expression in combination with radiotherapy might be expected to exert strong anti-tumor effect on hypoxic human hepatoma cells. -- Highlights: Black-Right-Pointing-Pointer miR-210 downregulation radiosensitized hypoxic hepatoma. Black-Right-Pointing-Pointer AIFM3 was identified as a direct target gene of miR-210. Black-Right-Pointing-Pointer miR-210 might be a therapeutic target to hypoxic hepatoma.

  20. Influence of bismuth on structural, elastic and spectroscopic properties of Nd{sup 3+} doped Zinc–Boro-Bismuthate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, Gaurav; Sontakke, Atul D.; Karmakar, P.; Biswas, K.; Balaji, S.; Saha, R.; Sen, R.; Annapurna, K., E-mail: annapurnak@cgcri.res.in

    2014-05-01

    The present investigation reports, influence of bismuth addition on structural, elastic and spectral properties of [(99.5−x) {4ZnO−3B_2O_3}−0.5Nd{sub 2}O{sub 3}−x Bi{sub 2}O{sub 3} where x=0, 5, 10, 20, 30, 40, 50 and 60] glasses. The measured FTIR reflectance spectra facilitated a thorough insight of methodical modifications that are arising in the glass structure from borate (build by BO{sub 3} and BO{sub 4} units) to bismuthate (BiO{sub 3} and BiO{sub 6} units) network due to the increase of bismuth content ensuing with a steady decrease in host phonon energy (ν{sub ph}). The elastic properties estimated from measured longitudinal and shear ultrasonic velocities (U{sub L} and U{sub s}) demonstrated the reduction in network rigidity of glasses on Bi{sub 2}O{sub 3} inclusion. The three phenomenological Judd–Ofelt intensity parameters (Ω{sub 2,4,6}) were obtained from recorded absorption spectra of Nd{sup 3+} ions in these glasses and have been used to predict radiative properties as a function of variation in bismuth content. The reduced host phonon energy and high optical basicity effect due to Bi{sub 2}O{sub 3} incorporation remarkably improved the Nd{sup 3+} luminescence properties such as emission intensity, quantum yield and emission cross-section. The quantum yield showed a strong increase from mere 16% in Zinc–Borate glass to almost 73% in 60 mol% Bi{sub 2}O{sub 3} containing glass. Similarly, the emission cross-section for Nd{sup 3+4}F{sub 3/2}→{sup 4}I{sub 11/2} laser transition raised from 2.43×10{sup −20} cm{sup 2} to 3.95×10{sup −20} cm{sup 2} in studied concentration suggesting a strong improvement in Nd{sup 3+} laser spectroscopic properties in Zinc–Boro-Bismuthate glass. These materials may be promising for compact solid state infrared lasers. - Highlights: • Continuous structural changes associated with reduction in host phonon energy by Bi{sub 2}O{sub 3} inclusion. • Ultrasonic velocity study revealed reduced Debye

  1. Phase transition of solid bismuth under high pressure

    International Nuclear Information System (INIS)

    Chen Hai-Yan; Xiang Shi-Kai; Yan Xiao-Zhen; Zhang Yi; Liu Sheng-Gang; Bi Yan; Zheng Li-Rong

    2016-01-01

    As a widely used pressure calibrator, the structural phase transitions of bismuth from phase I, to phase II, to phase III, and then to phase V with increasing pressure at 300 K have been widely confirmed. However, there are different structural versions for phase III, most of which are determined by x-ray diffraction (XRD) technology. Using x-ray absorption fine structure (XAFS) measurements combined with ab initio calculations, we show that the proposed incommensurate composite structure of bismuth of the three configurations is the best option. An abnormal continuous increase of the nearest-neighbor distance of phase III with elevated pressure is also observed. The electronic structure transformation from semimetal to metal is responsible for the complex behavior of structure transformation. (paper)

  2. Ac irreversibility line of bismuth-based high temperature superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Mehdaoui, A. [Laboratoire de Physique et de Spectroscopie Electronique, URA 1435 Faculte des Sciences, Universite de Haute Alsace 4, rue des Freres Lumiere, 68093 Mulhouse Cedex (France); Beille, J. [Laboratoire Louis Neel, CNRS, BP 166, 38042 Grenoble Cedex 9 (France); Berling, D.; Loegel, B. [Laboratoire de Physique et de Spectroscopie Electronique, URA 1435 Faculte des Sciences, Universite de Haute Alsace 4, rue des Freres Lumiere, 68093 Mulhouse Cedex (France); Noudem, J.G.; Tournier, R. [EPM-MATFORMAG, Laboratoire dElaboration par Procede Magnetique, CNRS, BP 166, 38042 Grenoble Cedex 9 (France)

    1997-09-01

    We discuss the magnetic properties of lead doped Bi-2223 bulk samples obtained through combined magnetic melt texturing and hot pressing (MMTHP). The ac complex susceptibility measurements are achieved over a broad ac field range (1 Oe{lt}h{sub ac}{lt}100 Oe) and show highly anisotropic properties. The intergranular coupling is improved in the direction perpendicular to the applied stress and magnetic field direction, and an intragranular loss peak is observed for the first time. A comparison is made with other bismuth-based compounds and it is shown that the MMTHP process shifts the ac irreversibility line (ac IL) toward higher fields. It is also shown that all the ac IL{close_quote}s for quasi 2D bismuth-based compounds show a nearly quadratic temperature dependence and deviate therefore strongly from the linear behavior observed in quasi 3D compounds and expected from a critical state model.{copyright} {ital 1997 Materials Research Society.}

  3. Ac irreversibility line of bismuth-based high temperature superconductors

    International Nuclear Information System (INIS)

    Mehdaoui, A.; Beille, J.; Berling, D.; Loegel, B.; Noudem, J.G.; Tournier, R.

    1997-01-01

    We discuss the magnetic properties of lead doped Bi-2223 bulk samples obtained through combined magnetic melt texturing and hot pressing (MMTHP). The ac complex susceptibility measurements are achieved over a broad ac field range (1 Oe ac <100 Oe) and show highly anisotropic properties. The intergranular coupling is improved in the direction perpendicular to the applied stress and magnetic field direction, and an intragranular loss peak is observed for the first time. A comparison is made with other bismuth-based compounds and it is shown that the MMTHP process shifts the ac irreversibility line (ac IL) toward higher fields. It is also shown that all the ac IL close-quote s for quasi 2D bismuth-based compounds show a nearly quadratic temperature dependence and deviate therefore strongly from the linear behavior observed in quasi 3D compounds and expected from a critical state model.copyright 1997 Materials Research Society

  4. Quantum nernst effect in a bismuth single crystal

    International Nuclear Information System (INIS)

    Matsuo, M.; Endo, A.; Hatano, N.; Nakamura, H.; Shirasaki, R.; Sugihara, K.

    2009-07-01

    We calculate the phonon-drag contribution to the transverse (Nernst) thermoelectric power S yx in a bismuth single crystal subjected to a quantizing magnetic field. The calculated heights of the Nernst peaks originating from the hole Landau levels and their temperature dependence reproduce the right order of magnitude for those of the pronounced magneto-oscillations recently reported by Behnia et al. A striking experimental finding that S yx is much larger than the longitudinal (Seebeck) thermoelectric power S xx can be naturally explained as the effect of the phonon drag, combined with the well-known relation between the longitudinal and the Hall resistivity ρ xx >> |ρ yx | in a semi-metal bismuth. The calculation that includes the contribution of both holes and electrons suggests that some of the hitherto unexplained minor peaks located roughly at the fractional filling of the hole Landau levels are attributable to the electron Landau levels. (author)

  5. Nanophotonic Modulator with Bismuth Ferrite as Low-loss Switchable Material

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia; Zhukovsky, Sergei; Lavrinenko, Andrei

    2015-01-01

    We propose a nanophotonic waveguide modulator with bismuth ferrite as a tunable material. Due to near-zero losses in bismuth ferrite, modulation with up to 20 dB/μm extinction ratio and 12 μm propagation length is achieved.......We propose a nanophotonic waveguide modulator with bismuth ferrite as a tunable material. Due to near-zero losses in bismuth ferrite, modulation with up to 20 dB/μm extinction ratio and 12 μm propagation length is achieved....

  6. Inhalation of {sup 210}Po and {sup 210}Pb from cigarette smoking in Poland

    Energy Technology Data Exchange (ETDEWEB)

    Skwarzec, B. E-mail: bosk@chemik.chem.univ.gda.pl; Ulatowski, J.; Struminska, D.I.; Borylo, A

    2001-07-01

    The carcinogenic effect of {sup 210}Po and {sup 210}Pb with respect to lung cancer is an important problem in many countries with very high cigarette consumption. Poland has one of the highest consumptions of cigarettes in the world. The results of {sup 210}Po determination on the 14 most frequently smoked brands of cigarettes which constitute over 70% of the total cigarette consumption in Poland are presented and discussed. Moreover, the polonium content in cigarette smoke was estimated on the basis of its activity in fresh tobaccos, ash, fresh filters and post-smoking filters. The annual effective doses were calculated on the basis of {sup 210}Po and {sup 210}Pb inhalation with the cigarette smoke. The results of this work indicate that Polish smokers who smoke one pack (20 cigarettes) per day inhale from 20 to 215 mBq of {sup 210}Po and {sup 210}Pb each. The mean values of the annual effective dose for smokers were estimated to be 35 and 70 {mu}Sv from {sup 210}Po and {sup 210}Pb, respectively. For persons who smoke two packs of cigarettes with higher radionuclide concentrations, the effective dose is much higher (471 {mu}Sv yr{sup -1}) in comparison with the intake in diet. Therefore, cigarettes and the absorption through the respiratory system are the main sources and the principal pathway of {sup 210}Po and {sup 210}Pb intake of smokers in Poland.

  7. Inhalation of 210Po and 210Pb from cigarette smoking in Poland

    International Nuclear Information System (INIS)

    Skwarzec, B.; Ulatowski, J.; Struminska, D.I.; Borylo, A.

    2001-01-01

    The carcinogenic effect of 210 Po and 210 Pb with respect to lung cancer is an important problem in many countries with very high cigarette consumption. Poland has one of the highest consumptions of cigarettes in the world. The results of 210 Po determination on the 14 most frequently smoked brands of cigarettes which constitute over 70% of the total cigarette consumption in Poland are presented and discussed. Moreover, the polonium content in cigarette smoke was estimated on the basis of its activity in fresh tobaccos, ash, fresh filters and post-smoking filters. The annual effective doses were calculated on the basis of 210 Po and 210 Pb inhalation with the cigarette smoke. The results of this work indicate that Polish smokers who smoke one pack (20 cigarettes) per day inhale from 20 to 215 mBq of 210 Po and 210 Pb each. The mean values of the annual effective dose for smokers were estimated to be 35 and 70 μSv from 210 Po and 210 Pb, respectively. For persons who smoke two packs of cigarettes with higher radionuclide concentrations, the effective dose is much higher (471 μSv yr -1 ) in comparison with the intake in diet. Therefore, cigarettes and the absorption through the respiratory system are the main sources and the principal pathway of 210 Po and 210 Pb intake of smokers in Poland

  8. Metabolism of 210Po in rats: Volatile 210Po from faeces

    International Nuclear Information System (INIS)

    Sadi, B. B.; Li, C.; Wyatt, H.; Bugden, M.; Wilkinson, D.; Kramer, G.

    2011-01-01

    The metabolic formation of volatile 210 Po species in a rat that was intravenously administered with 210 Po-citrate was investigated in this study. A slurry of the faecal sample was prepared in water and was bubbled with nitrogen gas in a closed system. The discharged gas was passed through a trapping device filled with liquid scintillation cocktail in order to capture any volatile 210 Po species. The amount of 210 Po trapped in the scintillation cocktail was measured by a liquid scintillation analyser that provided evidence of the presence of volatile 210 Po species in the faeces. The presence of volatile 210 Po in the faeces indicates that the metabolic formation of volatile 210 Po is likely to occur in the gut due to bacterial activity. The amount of volatile 210 Po species was compared with the daily faecal excretion of 210 Po. After 2 h of bubbling, the volatile 210 Po collected from the faeces sample was found to be between 1.0 and 1.7 % of the daily faecal excretion for the 4 d following 210 Po-citrate administration. (authors)

  9. Lead-210, polonium-210, and stable lead in the food-chain lichen, reindeer and man

    International Nuclear Information System (INIS)

    Persson, B.R.

    1972-01-01

    The measurements of stable lead and the natural fallout radionuclides lead-210 and polonium-210 in communities of lichen (Cladonia alpestris) in central Sweden from 1961 to 1970 indicate a quite constant level. The average lead-210 content per unit area in lichen carpets was found to be 15 +- 2 nCi m -2 , the average lead-210 activity concentration 6.7 +- 0.9 nCi per kg dry weight and the lead-210 specific activity 630 +- 60 nCi per g of stable lead. The polonium-210/lead-210 activity ratio was about 0.9 +- 0.1. The vertical distribution of lead-210 in the lichen carpet showed a maximum concentration in the top layer. The distribution was similar during 1967 and 1968 but the low amount of precipitation during 1968 and 1969 disturbed the distribution pattern in 1969 and 1970. The transfer of lead-210, polonium-210 and stable lead through the food chain: lichen, reindeer, and man was characterized. The absorbed dose rate in Lapps due to polonium-210 was estimated to be about 6 to 8 mrad per year in gonads and 8 to 20 mrad per year in bone tissues. This is about ten percent of their entire absorbed dose contribution from all natural radiation sources. (U.S.)

  10. Levels and transfer of 210Po and 210Pb in Nordic terrestrial ecosystems

    DEFF Research Database (Denmark)

    Brown, J.E.; Gjelsvik, R.; Roos, Per

    2011-01-01

    concentrations of the main dose forming radionuclides 210Po and 210Pb in biota from terrestrial ecosystems thus providing insight into the behaviour of these radioisotopes. Samples of soil, plants and animals were collected at Dovrefjell, Central Norway and Olkiluoto, Finland. Soil profiles from Dovrefjell...... exhibited an approximately exponential fall in 210Pb activity concentrations from elevated levels in humus/surface soils to “supported” levels at depth. Activity concentrations of 210Po in fauna (invertebrates, mammals, birds) ranged between 2 and 123 Bq kg−1 d.w. and in plants and lichens between 20...... and 138 Bq kg−1 d.w.. The results showed that soil humus is an important reservoir for 210Po and 210Pb and that fauna in close contact with this media may also exhibit elevated levels of 210Po. Concentration ratios appear to have limited applicability with regards to prediction of activity concentrations...

  11. Dose reduction using Bismuth protectors in chest computed tomography

    International Nuclear Information System (INIS)

    Anaya, R.

    2012-01-01

    This monography is about the Dose reduction using Bismuth protectors in chest CT. The radiation protection of specific areas is necessary when the tissues or radiosensitive organs are near the path of light beam. The correct use of protection represents a challenge for the radiologist because of the time and materials required. The method used was a prospective investigatio in CHPR (TC service) and the doses was measured with TLD dosimeters. It is important to use these protectors in children hospitals.

  12. Polonium-210 and lead-210 in food and tobacco products: a review of parameters and an estimate of potential exposure and dose

    Energy Technology Data Exchange (ETDEWEB)

    Watson, A.P.

    1983-07-01

    Food-chain transport of Pb-210 and Po-210 from soil to edible plant parts and from animal feed to meat and milk were evaluated from a review of literature. The degree of transfer was characterized by estimating concentration factors (unweighted arithmetic means) as well as the transfer coefficients B/sub v/, B/sub r/ (unweighted geometric means, f/sub m/ and f/sub f/ (unweighted arithmetic means). Global dietary intake of Pb-210 and Po-210 was also summarized, and 50-year dose estimates to target organs calculated. The greatest estimated ingestion doses were those to populations with large dietary complements of animal protein in the form of seafood (Japan) or caribou/reindeer muscle and organ meats (Arctic Eskimos and Lapps). The magnitude of this latter source illustrates the importance of simple food chains in generating significant exposures to populations dependent upon them. The origin and magnitude of inhalation exposure and dose from tobacco products was also assessed. For the majority of internal organs evaluated, the dose resulting from smoking commercially available tobacco products is comparable to or greater than the dose estimates for ingestion of naturally occurring dietary Pb-210 and Po-210.

  13. Polonium-210 and lead-210 in food and tobacco products: a review of parameters and an estimate of potential exposure and dose

    International Nuclear Information System (INIS)

    Watson, A.P.

    1983-07-01

    Food-chain transport of Pb-210 and Po-210 from soil to edible plant parts and from animal feed to meat and milk were evaluated from a review of literature. The degree of transfer was characterized by estimating concentration factors (unweighted arithmetic means) as well as the transfer coefficients B/sub v/, B/sub r/ (unweighted geometric means, f/sub m/ and f/sub f/ (unweighted arithmetic means). Global dietary intake of Pb-210 and Po-210 was also summarized, and 50-year dose estimates to target organs calculated. The greatest estimated ingestion doses were those to populations with large dietary complements of animal protein in the form of seafood (Japan) or caribou/reindeer muscle and organ meats (Arctic Eskimos and Lapps). The magnitude of this latter source illustrates the importance of simple food chains in generating significant exposures to populations dependent upon them. The origin and magnitude of inhalation exposure and dose from tobacco products was also assessed. For the majority of internal organs evaluated, the dose resulting from smoking commercially available tobacco products is comparable to or greater than the dose estimates for ingestion of naturally occurring dietary Pb-210 and Po-210

  14. Baseline concentration of 210Po and 210Pb in Sargassum from the northern Gulf

    International Nuclear Information System (INIS)

    Uddin, S.; Aba, A.; Bebhehani, M.

    2015-01-01

    Highlights: • This is the first baseline for 210 Po and 210 Pb in Sargassum from northern Gulf. • 210 Po concentration in Sargassum boveanum is higher than Sargassum oligocystum. • 210 Pb concentrations in two Sargassum species was not statistically significant. • The concentration factor is microalgae is slightly higher than IAEA recommended value. - Abstract: This baseline study highlights the 210 Po and 210 Pb concentration in two species of the benthic macroalgae Sargassum from northern Gulf, also known as the ROPME Sea Area (RSA). Within the marine environment, 210 Po is initially absorbed from water and concentrated by phytoplankton and macroalgae, and this concentrated 210 Po can then readily be passed along to the higher trophic level of the marine food web. The 210 Po concentration measured in Sargassum boveanum (22.5–25.6 Bq kg −1 ) was higher than that in Sargassum oligocystum (20.2–22.5 Bq kg −1 ), but is not statistically significant (p > 0.064), where as the difference between 210 Pb concentrations in Sargassum boveanum (15.3–16.8 Bq kg −1 ) and Sargassum oligocystum (18.4–22.0 Bq kg −1 ) was statistically significant (p > 0.019). The measured concentration factor for 210 Po in Sargassum in the northern Gulf varied between 0.55 and 1.2 × 10 4 , values higher to the IAEA recommended value of 1 × 10 3 . The 210 Po enrichment is observed in both the species of Sargassum, 210 Po/ 210 Pb ratio was >1 at all the stations for all the samples

  15. Oxide layer stability in lead-bismuth at high temperature

    Science.gov (United States)

    Martín, F. J.; Soler, L.; Hernández, F.; Gómez-Briceño, D.

    2004-11-01

    Materials protection by 'in situ' oxidation has been studied in stagnant lead-bismuth, with different oxygen levels (H 2/H 2O ratios of 0.3 and 0.03), at temperatures from 535 °C to 600 °C and times from 100 to 3000 h. The materials tested were the martensitic steels F82Hmod, EM10 and T91 and the austenitic stainless steels, AISI 316L and AISI 304L. The results obtained point to the existence of an apparent threshold temperature above which corrosion occurs and the formation of a protective and stable oxide layer is not possible. This threshold temperature depends on material composition, oxygen concentration in the liquid lead-bismuth and time. The threshold temperature is higher for the austenitic steels, especially for the AISI 304L, and it increases with the oxygen concentration in the lead-bismuth. The oxide layer formed disappear with time and, after 3000 h all the materials, except AISI 304L, suffer corrosion, more severe for the martensitic steels and at the highest temperature tested.

  16. Theoretical study of bismuth-doped cadmium telluride

    Science.gov (United States)

    Menendez-Proupin, E.; Rios-Gonzalez, J. A.; Pena, J. L.

    Cadmium telluride heavily doped with bismuth has been proposed as an absorber with an intermediate band for solar cells. Increase in the photocurrent has been shown recently, although the overall cell efficiency has not improved. In this work, we study the electronic structure and the formation energies of the defects associated to bismuth impurities. We have performed electronic structure calculations within generalized density functional theory, using the exchange-correlation functional HSE(w) , where the range-separation parameter w has been tuned to reproduce the CdTe bandgap. Improving upon previous reports, we have included the spin-orbit interaction, which modifies the structure of the valence band and the energy levels of bismuth. We have found that interstitial Bi (Bii) tends to occupy Cd vacancies, cadmium substitution (BiCd) creates single donor level, while tellurium substitution (BiTe) is a shallow single acceptor. We investigate the interaction between these point defects and how can they be combined to create a partially filled intermediate band. Supported by FONDECYT Grant 1130437, CONACYT-SENER SUSTENTABILIDAD ENERGETICA/project CeMIE-Sol PY-207450/25 and PY-207450/26. JARG acknowledges CONACYT fellowship for research visit. Powered@NLHPC (ECM-02).

  17. Study of barium bismuth titanate prepared by mechanochemical synthesis

    Directory of Open Access Journals (Sweden)

    Lazarević Z.Ž.

    2009-01-01

    Full Text Available Barium-bismuth titanate, BaBi4Ti4O15 (BBT, a member of Aurivillius bismuth-based layer-structure perovskites, was prepared from stoichiometric amounts of barium titanate and bismuth titanate obtained via mechanochemical synthesis. Mechanochemical synthesis was performed in air atmosphere in a planetary ball mill. The reaction mechanism of BaBi4Ti4O15 and the preparation and characteristics of BBT ceramic powders were studied using XRD, Raman spectroscopy, particle analysis and SEM. The Bi-layered perovskite structure of BaBi4Ti4O15 ceramic forms at 1100 °C for 4 h without a pre-calcination step. The microstructure of BaBi4Ti4O15 exhibits plate-like grains typical for the Bi-layered structured material and spherical and polygonal grains. The Ba2+ addition leads to changes in the microstructure development, particularly in the change of the average grain size.

  18. Aerosol deposition of (Cu,Ti) substituted bismuth vanadate films

    Energy Technology Data Exchange (ETDEWEB)

    Exner, Jörg, E-mail: Functional.Materials@Uni-Bayreuth.de [University of Bayreuth, Department of Functional Materials, Universitätsstraße 30, 95440 Bayreuth (Germany); Fuierer, Paul [Materials and Metallurgical Engineering Department, New Mexico Institute of Mining and Technology, Socorro, NM 87801 (United States); Moos, Ralf [University of Bayreuth, Department of Functional Materials, Universitätsstraße 30, 95440 Bayreuth (Germany)

    2014-12-31

    Bismuth vanadate, Bi{sub 4}V{sub 2}O{sub 11}, and related compounds with various metal (Me) substitutions, Bi{sub 4}(Me{sub x}V{sub 1−x}){sub 2}O{sub 11−δ}, show some of the highest ionic conductivities among the known solid oxide electrolytes. Films of Cu and Ti substituted bismuth vanadate were prepared by an aerosol deposition method, a spray coating process also described as room temperature impact consolidation. Resultant films, several microns in thickness, were dense with good adhesion to the substrate. Scanning electron microscopy and high temperature X-ray diffraction were used to monitor the effects of temperature on the structure and microstructure of the film. The particle size remained nano-scale while microstrain decreased rapidly up to 500 °C, above which coarsening and texturing increased rapidly. Impedance measurements of films deposited on inter-digital electrodes revealed an annealing effect on the ionic conductivity, with the conductivity exceeding that of a screen printed film, and approaching that of bulk ceramic. - Highlights: • Cu and Ti doped bismuth vanadate films were prepared by aerosol deposition (AD). • Dense 3–5 μm thick films were deposited on alumina, silicon and gold electrodes. • Annealing of the AD-layer increases the conductivity by 1.5 orders of magnitude. • Effect of temperature on structure and microstructure was investigated.

  19. Soluble Lead and Bismuth Chalcogenidometallates: Versatile Solders for Thermoelectric Materials

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Hao [Department; Son, Jae Sung [Department; School; Dolzhnikov, Dmitriy S. [Department; Filatov, Alexander S. [Department; Hazarika, Abhijit [Department; Wang, Yuanyuan [Department; Hudson, Margaret H. [Department; Sun, Cheng-Jun [Advanced; Chattopadhyay, Soma [Physical; Talapin, Dmitri V. [Department; Center

    2017-07-27

    Here we report the syntheses of largely unexplored lead and bismuth chalcogenidometallates in the solution phase. Using N2H4 as the solvent, new compounds such as K6Pb3Te6·7N2H4 were obtained. These soluble molecular compounds underwent cation exchange processes using resin chemistry, replacing Na+ or K+ by decomposable N2H5+ or tetraethylammonium cations. They also transformed into stoichiometric lead and bismuth chalcogenide nanomaterials with the addition of metal salts. Such a versatile chemistry led to a variety of composition-matched solders to join lead and bismuth chalcogenides and tune their charge transport properties at the grain boundaries. Solution-processed thin films composed of Bi0.5Sb1.5Te3 microparticles soldered by (N2H5)6Bi0.5Sb1.5Te6 exhibited thermoelectric power factors (~28 μW/cm K2) comparable to those in vacuum-deposited Bi0.5Sb1.5Te3 films. The soldering effect can also be integrated with attractive fabrication techniques for thermoelectric modules, such as screen printing, suggesting the potential of these solders in the rational design of printable and moldable thermoelectrics.

  20. Shape-controlled solvothermal synthesis of bismuth subcarbonate nanomaterials

    International Nuclear Information System (INIS)

    Cheng Gang; Yang Hanmin; Rong Kaifeng; Lu Zhong; Yu Xianglin; Chen Rong

    2010-01-01

    Much effort has been devoted to the synthesis of novel nanostructured materials because of their unique properties and potential applications. Bismuth subcarbonate ((BiO) 2 CO 3 ) is one of commonly used antibacterial agents against Helicobacter pylori (H. pylori). Different (BiO) 2 CO 3 nanostructures such as cube-like nanoparticles, nanobars and nanoplates, were fabricated from bismuth nitrate via a simple solvothermal method. The nanostructures were characterized by powder X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). It was found that the solvents and precursors have an influence on the morphologies of (BiO) 2 CO 3 nanostructures. The possible formation mechanism of different (BiO) 2 CO 3 nanostructures fabricated under different conditions was also discussed. - Graphical abstract: Different bismuth subcarbonate ((BiO) 2 CO 3 ) nanostructures were successfully synthesized by a simple solvothermal method. It was found that the solvents and precursors have an influence on the morphologies of (BiO) 2 CO 3 nanostructures.

  1. Bismuth Oxysulfide and Its Polymer Nanocomposites for Efficient Purification

    Directory of Open Access Journals (Sweden)

    Yidong Luo

    2018-03-01

    Full Text Available The danger of toxic organic pollutants in both aquatic and air environments calls for high-efficiency purification material. Herein, layered bismuth copper oxychalcogenides, BiCuSO, nanosheets of high photocatalytic activity were introduced to the PVDF (Polyvinylidene Fluoride. The fibrous membranes provide an easy, efficient, and recyclable way to purify organic pollutant. The physical and photophysical properties of the BiCuSO and its polymer composite were characterized by scanning electron microscopy (SEM, X-ray diffraction (XRD, ultraviolet-visible diffuse reflection spectroscopy (DRS, X-ray photoelectron spectroscopy (XPS, electron spin resonance (EPR. Photocatalysis of Congo Red reveals that the BiCuSO/PVDF shows a superior photocatalytic activity of a 55% degradation rate in 70 min at visible light. The high photocatalytic activity is attributed to the exposed active {101} facets and the triple vacant associates V B i ‴ V O • • V B i ‴ . By engineering the intrinsic defects on the surface of bismuth oxysulfide, high solar-driven photocatalytic activity can be approached. The successful fabrication of the bismuth oxysulfide and its polymer nanocomposites provides an easy and general approach for high-performance purification materials for various applications.

  2. Nafion/2,2'-bipyridyl-modified bismuth film electrode for anodic stripping voltammetry

    International Nuclear Information System (INIS)

    Torma, Ferenc; Kadar, Mihaly; Toth, Klara; Tatar, Eniko

    2008-01-01

    This paper describes the fabrication, characterisation and the application of a Nafion/2,2'-bipyridyl/bismuth composite film-coated glassy carbon electrode (NC(Bpy)BiFE) for the anodic stripping voltammetric determination of trace metal ions (Zn 2+ , Cd 2+ and Pb 2+ ). The NC(Bpy)BiFE electrode is prepared by first applying a 2.5 mm 3 drop of a coating solution containing 0.5 wt% Nafion and 0.1% (w/v) 2,2'-bipyridil (Bpy) onto the surface of a glassy carbon electrode, while the Bi film was plated in situ simultaneously with the target metal ions at -1.4 V. The main advantage of the polymer coated bismuth film electrode is that the sensitivity of the stripping responses is increased considerably due to the incorporation of the neutral chelating agent of 2,2'-bipyridyl (Bpy) in the Nafion film, while the Nafion coating improved the mechanical stability of the bismuth film and its resistance to the interference of surfactants. The key experimental parameters relevant to both the electrode fabrication and the voltammetric measurement were optimized on the basis of the stripping signals. With a 2 min deposition time in the presence of oxygen, linear calibration curves were obtained in a wide concentration range (about 2-0.001 μM) with detection limits of 8.6 nM (0.56 μg dm -3 ) for Zn 2+ , 1.1 nM (0.12 μg dm -3 ) for Cd 2+ and 0.37 nM (0.077 μg dm -3 ) for Pb 2+ . For nine successive preconcentration/determination/electrode renewal experiments the standard deviations were between 3 and 5% at 1.2 μM for zinc and 0.3-0.3 μM concentration level for lead and cadmium, respectively, and the method exhibited excellent selectivity in the presence of the excess of several potential interfering metal ions. The analytical utility of the stripping voltammetric method elaborated was tested in the assay of heavy metals in some real samples and the method was validated by ICP-MS technique

  3. Determination of {sup 210}Pb and {sup 210}Po in cigarette tobacco; Determinacao de {sup 210}Pb e {sup 210}Po em tabaco de cigarros nacionais

    Energy Technology Data Exchange (ETDEWEB)

    Peres, Ana Claudia

    1999-07-01

    Cigarette smoking is one of the important pathways that could contribute to enhance the radiation dose to man, due to the relatively large concentrations of {sup 210}Pb and {sup 210}Po found in tobacco leaves. In this work, concentrations of these two radionuclides were determined in eight of the most commercialized cigarette brands produced in Brazil. The samples analyzed were bought randomly in the market. The {sup 210}Pb was determined by counting the beta activity of the {sup 210}Bi in a gas flow proportional detector, after radiochemical separation and precipitation of the PbCr0{sub 4}. The {sup 210}Po was determined by alpha spectrometry, using a surface barrier detector, after radiochemical separation and spontaneous deposition of Po in copper disk. The results showed concentrations ranging from 11,9 to 30,2 mBq per gram of dry tobacco for {sup 210}Pb and from 10,9 to 27,4 mBq per gram of dry tobacco for {sup 210}Po. (author)

  4. Diagenesis and {sup 210}Pb; Diagenesis y {sup 210}Pb

    Energy Technology Data Exchange (ETDEWEB)

    Ruiz-Fernandez, Ana Carolina [Universidad Nacional Autonoma de Mexico, Instituto de Ciencias del Mar y Limnologia (Mexico); Sanchez-Cabeza, Joan-Albert [Organismo Internacional de la Energia Atomica, Laboratorios del Medio Marino (Monaco)

    2012-07-01

    One of the basic questions when studying cores for historical reconstructions of environmental changes is whether the profiles of {sup 210}Pb heavy metals and temporal distributions represent actual or have been affected by diagenetic processes. The term refers to processes occurring in the sediment during and after its formation. Such processes can be physical (such as water loss by compaction in clay sludge), biogeochemical (as the decomposition of organic matter) or biological (eg the ingestion of sediments by infauna.) In this chapter we will refer specifically to diagenetic processes caused by the establishment of a vertical zonation of redox conditions and their effects on concentrations of Fe, Mn and other redox-sensitive metals associated. The redox conditions (defined redox potential Eh) of sediments are primarily controlled by the bacterial decomposition of sedimentary organic matter, and are limited by the rate of supply of organic matter (primary production or other sources) and the rate at that accumulates (rate of accumulation of organic matter). During the bacterial decomposition occurs a sequence of reactions involving a succession of oxidants (or electron acceptors) between which the primary oxidant is O{sub 2}. However, when the dissolved O{sub 2} is consumed and the redox potential has decreased enough to favor the most efficient oxidizing the organic matter decomposition can continue through secondary sources of oxidants (suboxic diagenesis). [Spanish] Una de las preguntas basicas cuando estudiamos cores para realizar reconstrucciones historicas de cambios ambientales es si los perfiles de {sup 210}Pb y metales pesados representan las distribuciones temporales reales o si han sido afectados por procesos diageneticos. El termino diagenesis sedimentaria se refiere a los procesos que ocurren en el sedimento durante y despues de su formacion. Estos procesos pueden ser fisicos (como la perdida de agua en lodos arcillosos por compactacion

  5. Po-210 and Pb-210 in water and fish from Taboshar uranium mining Pit Lake, Tajikistan

    International Nuclear Information System (INIS)

    Skipperud, L.; Jørgensen, A.G.; Heier, L.S.; Salbu, B.; Rosseland, B.O.

    2013-01-01

    Polonium-210 in water and 210 Pb and 210 Po in different fish organs from 3 different fish species in Taboshar Pit Lake (n = 13), located in the uranium mining area in Tajikistan, and in Kairakkum Reservoir (reference lake, n = 3), have been determined as part of a Joint project between Norway, Kazakhstan, Kyrgyzstan and Tajikistan. The average activity concentration of 210 Pb and 210 Po in liver, muscle and bone of Carassius auratus was higher than the concentration in similar tissues of C. carpio and Sander lucioperca from the reference site. The accumulation of 210 Po was higher than for 210 Pb, and the accumulation of 210 Po was highest in the liver of C. auratus (3673 ± 434 Bq kg −1 ww). Although the average activity concentration of 210 Pb in liver and bones of C. auratus from Pit Lake were fairly similar, a huge variation in the liver activity concentrations (25–327 Bq kg −1 ww) was found. The results confirm direct uptake of unsupported 210 Po into the liver, and that the distributions of 210 Po and 210 Pb in fish organs were different. The BCF (L/kg) for 210 Po in bone, liver and muscle clearly demonstrates high accumulation of 210 Po in C. auratus, especially in the liver. The average BCFs of liver, bone and muscle were >1.4 × 10 5 , >2.5 × 10 4 and >1.4 × 10 4 , respectively. All fish in the Pit Lake were found to be in the same trophic level, however, a linear correlation between log 210 Po in liver and δ 15 N could indicate biomagnification of 210 Po in liver of C. auratus. In regards to the recommended Annual Limit of Intake (ALI) for 210 Po, the concentration of 210 Po in muscle tissues of C. auratus is alarming, as there is a high probability for the local population at risk to exceed the recommended ALI through consumption of fish from Taboshar Pit Lake

  6. Study on corrosion test techniques in lead bismuth eutectic flow. Joint research report in JFY2002

    International Nuclear Information System (INIS)

    Takahashi, Minoru; Sekimoto, Hiroshi

    2003-03-01

    The evaluation of corrosion behaviors of core and structural materials in lead bismuth eutectic is one of the key issues for the utilization of lead bismuth eutectic as a coolant of the primary loops of lead bismuth cooled fast breeder reactors (FBRs) and the intermediate heat transport media of new-type steam generators of the sodium cooled FBRs. The purpose of the present study is to establish corrosion test techniques in lead bismuth eutectic flow. The techniques of steel corrosion test and oxygen control in flowing lead bismuth eutectic, and the technologies of a lead bismuth flow test at high temperature and high velocity were developed through corrosion test using a lead bismuth flow test loop of the Tokyo Institute of Technology in JFY2002. The major results are summarized as follows: (1) Techniques of fabrication, mount and rinse of corrosion specimens, measurement method of weight loss, and SEM/EDX analysis method have been established through lead bismuth corrosion test. (2) Weight losses were measured, corrosion and lead bismuth-adhered layers and eroded parts were observed in two 1000 hr-corrosion tests, and the results were compared with each other for twelve existing steels including ODS, F82H and SUH-3. (3) An oxygen sensor made of zirconia electrolyte structurally resistant to thermal stress and thermal shock was developed and tested in the lead bismuth flow loop. Good performance has been obtained. (4) An oxygen control method by injecting argon and hydrogen mixture gas containing steam into lead bismuth was applied to the lead bismuth flow loop, and technical issues for the development of the oxygen control method were extracted. (5) Technical measures for freezing and leakage of lead bismuth in the flow loop were accumulated. (6) Technical measures for flow rate decrease/blockage due to precipitation of oxide and corrosion products in a low temperature section of the lead bismuth flow loop were accumulated. (7) Electromagnetic flow meters with MI

  7. 210Pb and 210Po Determination in Bottled Water Available on the Croatian Market

    International Nuclear Information System (INIS)

    Rogic, M.; Rozmaric Macefat, M.; Benedik, Lj.; Strok, M.

    2011-01-01

    An alpha emitting radionuclide 210Po and beta emitting radionuclide 210Pb are decay products of 238U. Due to their nuclear properties they are considered as radionuclides with the highest radiotoxicity and contribute significantly to the internal dose to the population received by drinking water. For radiological impact assessment 210Pb and 210Po must be measured routinely and accurately, with low detection limits. The aim of our study was determination of activity concentrations of 210Pb and 210Po in bottled drinking and mineral waters available on Croatian market. For their determination a procedure for their simultaneous separation from the water samples was used. After addition of 209Po tracer and lead carrier, radionuclides were preconcentrated from large volume by MnO 2 and their separation from interfering elements by Sr resin was done. 210Po source for alpha-particle spectrometric measurement was prepared by selfdeposition on silver disc, while lead was precipitated as lead sulphate and the beta activity of its daughter 210Bi was counted on a beta proportional counter. The results obtained show that values for activity concentrations of 210Pb and 210Po in all examined waters are in accordance with allowed activity concentration according to the European Commission Recommendation 2001/928/Euratom and Guidelines for Drinking Water Quality, published by WHO in 2006. (author)

  8. Biogeochemistry of (210)Pb and (210)Po in fresh waters and sediments. Doctoral thesis

    International Nuclear Information System (INIS)

    Benoit, G.

    1988-06-01

    The geochemical cycling of (210)Pb in a Massachusetts lake was studied. A mass balance for the epilimnion showed that (210)Pb inputs by precipitation were matched by outputs on settling particles, so direct uptake by bottom sediments was inconsequential. Below the epilimnion, vertical mixing was very low because of a steep temperature/density gradient, and this limited vertical transport. Anoxic conditions caused remobilization of iron and (210)Pb, which reprecipitated at the oxycline and returned to the bottom via settling. Below the zone of precipitation, (210)Pb and iron distributions resulted from constant release from anoxic sediments and dilution in the water column. Sediment (210)Pb distributions were caused by sedimentation and Fickian transport. The Fickian component was equal to the pore water diffusive flux. In pore waters, (210)Pb and (210)Po were 100 times greater that in overlying water and had steep concentration gradients, unlike Fe, Mn, S(-II), and alkalinity. (210)Pb partition coefficients decreased from 15000 to 1500 with depth controlled by sorption on iron oxides. Remobilization to the water column comes from a thin layer of iron-rich floc near the sediment/water interface. Deeper in the cores, diffusive transport can cause redistribution of (210)Pb to an extent that can affect (210)Pb dating

  9. Intake of 226Ra, 210Pb and 210Po with food in Poland

    International Nuclear Information System (INIS)

    Pietrzak-Flis, Z.; Chrzanowski, E.; Dembinska, S.

    1997-01-01

    Intake with food and water of 226 Ra, 210 Pb and 210 Po was determined for an adult population in regions of central, northern and northeastern Poland. The content of radionuclides was determined in the daily diet and, in the central region, also in foodstuffs and drinking water. The annual intake with foodstuffs was estimated on the basis of their average annual consumption. The 226 Ra intake in northeastern Poland was approximately 17% higher than the overall average, correlating well with the higher concentration of this radionuclide in the soil. The 210 Po/ 210 Pb ratio was close to unity in the continental regions, whereas at the Baltic Sea coast it was approximately 1.5. The latter value can be ascribed to a larger consumption of fish for which the 210 Po/ 210 Pb ratio was found to be approximately 10. In central Poland the largest intake of 226 Ra was with flour and vegetables (contribution approx. 60%), the largest intake of 210 Pb was with flour and meat (approx. 50%) and the largest intake of 210 Po was with fish (approx. 34%). From the intake and dose coefficient, annual effective doses were calculated. The dose from 210 Pb and 210 Po was approx. 54 μSv year -1 , and the dose from 226 Ra was approx. 4 μSv year -1

  10. 17 CFR 210.3A-01 - Application of § 210.3A-01 to § 210.3A-05.

    Science.gov (United States)

    2010-04-01

    ... Financial Statements § 210.3A-01 Application of § 210.3A-01 to § 210.3A-05. Sections 210.3A-01 to 210.3A-05 shall govern the presentation of consolidated and combined financial statements. [44 FR 19386, Apr. 3... COMMISSION FORM AND CONTENT OF AND REQUIREMENTS FOR FINANCIAL STATEMENTS, SECURITIES ACT OF 1933, SECURITIES...

  11. Use of lead-210 and polonium-210 as tracers of atmospheric processes

    International Nuclear Information System (INIS)

    Nevissi, A.; Schell, W.R.

    1980-01-01

    The inputs of 210 Pb and 210 Po have been measured in two marine environments to trace atmospheric processes. Precipitation and dry fallout samples were collected monthly at Seattle, Wash., over a period of 4 years, and air filter samples were collected biweekly at the ground level on Amchitka Island, Alaska, over a period of 3 years. The results for both stations show that 210 Pb undergoes seasonal variations in surface deposition with minimum values in relatively dry months of summer and maximum values in the fall or winter. The seasonal variations of 210 Pb are attributed to several factors including: 210 Pb content of the air masses involved, changes in the meteorological conditions, and local input of 210 Pb as a result of radon exhalation and soil resuspension

  12. Aspects on the analysis of 210Po.

    Science.gov (United States)

    Henricsson, F; Ranebo, Y; Holm, E; Roos, P

    2011-05-01

    There has been little development regarding analysis of polonium (Po) in environmental samples since the 1960 ies. This is due to the straightforward spontaneous deposition of this element on silver (Ag), nickel (Ni) or copper (Cu) without any radiochemical separation. For many years, no radiochemical yield determinant was used and it was generally supposed that the yield was 100% after two depositions. Counting was often done using ZnS scintillation counter coupled to a photomultiplier tube. However, the use of the yield determinants (208)Po and (209)Po and the development of alpha spectrometry showed that the yield was lower. Furthermore, the tendency of Po to volatilize at low temperatures constrains the sample preparation techniques; dry-ashing cannot be used. But during the wet-ashing procedure, there are still some losses. The aim of this study was to evaluate the Po losses during wet-ashing by the use of a double-tracer technique. We have found that the losses were about 30% when open glass beakers were used and about 17% when the samples were digested in microwave oven. When long-necked bottles (Kjeldahl flasks) were used, a loss of about 20% was registered. It has also been observed that (210)Pb to some extent is plating out together with its daughter nuclide Po during the electrochemical deposition. This will result in a systematic error since an unknown amount of supported (210)Po will be produced from the (210)Pb decay depending on the fraction of (210)Pb being deposited on the disc and the waiting time between deposition and measurement of the sample. A further consequence of this is that in the assessment of the (210)Pb content in the sample, very often the remaining liquid is stored after deposition for build-up of (210)Po. Since some (210)Pb is lost on the disc, the result for (210)Pb will be too low. Both these systematic errors give rise to a too high (210)Po/(210)Pb ratio. The fraction of (210)Pb which is plating out has been assessed in this

  13. A single drug for Helicobacter pylori infection: first results with a new bismuth triple monocapsule

    NARCIS (Netherlands)

    de Boer, W. A.; van Etten, R. J.; Schneeberger, P. M.; Tytgat, G. N.

    2000-01-01

    In this pilot study we investigated the efficacy and tolerability of a new monocapsule that contains a bismuth compound, tetracycline, and metronidazole. If proven to be effective, this monotherapy would turn the well-accepted multidrug regimen of standard bismuth-based triple therapy into an easy

  14. Method of Creating Micro-scale Silver Telluride Grains Covered with Bismuth Nanoparticles

    Science.gov (United States)

    Kim, Hyun-Jung (Inventor); Choi, Sang Hyouk (Inventor); King, Glen C. (Inventor); Park, Yeonjoon (Inventor); Lee, Kunik (Inventor)

    2014-01-01

    Provided is a method of enhancing thermoelectric performance by surrounding crystalline semiconductors with nanoparticles by contacting a bismuth telluride material with a silver salt under a substantially inert atmosphere and a temperature approximately near the silver salt decomposition temperature; and recovering a metallic bismuth decorated material comprising silver telluride crystal grains.

  15. Build-up enhancement of photoluminescence from phenylazomethine bismuth dendrimer using Bi(OTf)3

    Science.gov (United States)

    Kambe, Tetsuya; Imaoka, Shotaro; Imaoka, Takane; Yamamoto, Kimihisa

    2018-05-01

    Metal assembly to a dendrimer can provide various functionalities based on the branched structure. Here, we researched assembly phenomena of bismuth salts in the phenylazomethine dendrimer and achieved enhancement of emission intensity per metal unit by using Bi(OTf)3. This enhancement suggested increasing of Bi-N coordination bonds derived from the bismuth units in the dendrimer.

  16. Selective oxidation of propylene to acrolein by silica-supported bismuth molybdate catalysts

    DEFF Research Database (Denmark)

    Duc, Duc Truong; Ha, Hanh Nguyen; Fehrmann, Rasmus

    2011-01-01

    Silica-supported bismuth molybdate catalysts have been prepared by impregnation, structurally characterized and examined as improved catalysts for the selective oxidation of propylene to acrolein. Catalysts with a wide range of loadings (from 10 to 90 wt%) of beta bismuth molybdate (β-Bi2Mo2O9) w...

  17. Speciation of 210Po and 210Pb in air particulates determined by sequential extraction.

    Science.gov (United States)

    Al-Masri, M S; Al-Karfan, K; Khalili, H; Hassan, M

    2006-01-01

    Speciation of (210)Po and (210)Pb in air particulates of two Syrian phosphate sites with different climate conditions has been studied. The sites are the mines and Tartous port at the Mediterranean Sea. Air filters were collected during September 2000 until February 2002 and extracted chemically using different selective fluids in an attempt to identify the different forms of these two radionuclides. The results have shown that the inorganic and insoluble (210)Po and (210)Pb (attached to silica and soluble in mineral acids) portion was found to be high in both sites and reached a maximum value of 94% and 77% in the mine site and Tartous port site, respectively. In addition, only 24% of (210)Pb in air particulates was found to be associated with organic materials probably produced from the incomplete burning of fuel vehicle and similar activities. Moreover, the (210)Po/(210)Pb activity ratio in air particulates was higher than that in all samples at both sites and varied between 3.85 in November 2000 at Tartous port site and 20 in April 2001 at the mine area. These activity ratios were also higher than the natural levels. The (210)Po/(210)Pb activity ratio was also determined in each portion resulting from the selective extraction and found to be higher than that in most samples. The sources of (210)Po excess in these portions are discussed. Soil suspension, which is common in the dry climate dominant in the area, sea water spray and heating of phosphate ores were considered; polonium is more volatile than the lead compounds at even moderate temperature. Furthermore, variations in the chemical forms of (210)Po and (210)Pb during the year were also investigated. However, the results of this study can also be utilized for dose assessment to phosphate industry workers.

  18. The speciation and determination of 210Pb and 210Po in soil samples

    International Nuclear Information System (INIS)

    Jia Guogang; Liu Senlin; Xu Changheng; Xiao Xuefu; Chen Ling; Yang Hetao; Maria Belli; Umberto Sansone; Silvia Rosamilia; Stefania Gaudino

    2005-01-01

    A method for speciation and determination of 21 0Pb and 210 Po in soil samples was developed. The speciation was carried out by fractionating the soil samples into 5 fractions which are water soluble or exchangeable, bound to carbonates, bound to Fe-Mn oxides, bound to organic matter and bound to residue. After mineralisation, 10% solution of each fraction was used to spontaneously deposit polonium on a silver disk at 85-90 degree C and pH 1.5 and 210 Po was measured by α-spectrometry; the remain solution was used to separate lead by anion-exchange resin and purified by precipitation as PbS and PbSO 4 , and 210 Pb was determined by a low background β-counter. IAEA-327 reference material (soil) has been studied for 210 Pb and 210 Po speciation. The results show that: (1) the average yields are 88.7±6.4% for 210 Pb and 93.8±8.2% for 210 Po; (2) if compared to the total 210 Pb activity in the sample, 210 Pb fractions are 0.95% in exchangeable form, 10.6% bound to carbonates, 14.3% bound to Fe-Mn oxides, 7.00% bound to organic matter, and 67.2% bound to residue or acid soluble, and the corresponding values for 210 Po are 0.17%, 0.97%, 21.0%, 0.47% and 77.4%, respectively; and (3) the obtained 210 Pb concentration is in good agreement with the recommended value given by IAEA.

  19. Polonium-210 in Euphauslids: A Detailed Study

    Energy Technology Data Exchange (ETDEWEB)

    Heyraud, M.; Fowler, S. W.; Beasley, T. M.; Cherry, R. D.

    1976-07-01

    A detailed study of {sup 210}Po, the predominant alpha-emitting nuclide found in most marine organisms, has been undertaken in a particular zooplanktonic species, the euphausiid Meganyctiphanes norvegica. The purpose was to obtain information concerning the origin, the localization and the flux of the nuclide in and through this organism. Measurements of {sup 210}Po were made in euphausiids of different sizes, in dissected organs and tissues, and in excretion products. The results show higher concentrations in the smaller specimens; this fact cannot be explained on the basis of surface adsorption, but is probably related to the ingestion of food. Dissection results show that the distribution of {sup 210}Po in euphausiids is not homogeneous, but that the majority is concentrated in the internal organs, the alimentary tract and the hepatopancreas in particular. The natural radiation dose received by these organs is in consequence much higher than that received by the whole animal. Use of a dynamic model allowed the flux of {sup 210}Po through M. norvegica to be calculated. The calculations confirm that food is the principal sauce of {sup 210}Po for this species, and clearly show that fecal pellets constitute the major elimination route. Extrapolation of the data to zooplankton in general leads to the conclusion that zooplankton metabolic activity plays an important role in transporting {sup 210}Po from the surface layers of the ocean to depth. (author)

  20. Polonium-210 in Euphauslids: A Detailed Study

    International Nuclear Information System (INIS)

    Heyraud, M.; Fowler, S.W.; Beasley, T.M.; Cherry, R.D.

    1976-01-01

    A detailed study of 210 Po, the predominant alpha-emitting nuclide found in most marine organisms, has been undertaken in a particular zooplanktonic species, the euphausiid Meganyctiphanes norvegica. The purpose was to obtain information concerning the origin, the localization and the flux of the nuclide in and through this organism. Measurements of 210 Po were made in euphausiids of different sizes, in dissected organs and tissues, and in excretion products. The results show higher concentrations in the smaller specimens; this fact cannot be explained on the basis of surface adsorption, but is probably related to the ingestion of food. Dissection results show that the distribution of 210 Po in euphausiids is not homogeneous, but that the majority is concentrated in the internal organs, the alimentary tract and the hepatopancreas in particular. The natural radiation dose received by these organs is in consequence much higher than that received by the whole animal. Use of a dynamic model allowed the flux of 210 Po through M. norvegica to be calculated. The calculations confirm that food is the principal sauce of 210 Po for this species, and clearly show that fecal pellets constitute the major elimination route. Extrapolation of the data to zooplankton in general leads to the conclusion that zooplankton metabolic activity plays an important role in transporting 210 Po from the surface layers of the ocean to depth. (author)

  1. Polonium-210 in euphausiids: a detailed study

    Energy Technology Data Exchange (ETDEWEB)

    Heyraud, M; Fowler, S W; Beasley, T M; Cherry, R D

    1976-02-13

    A detailed study of /sup 210/Po, the predominant alpha-emitting nuclide found in most marine organisms, has been undertaken in a particular zooplanktonic species, the euphausiid Meganyctiphanes norvegica. Information was obtained concerning the origin, the localization and the flux of the nuclide in and through the organism. Measurements of /sup 210/Po were made in euphausiids of different sizes, in dissected organs and tissues, and in excretion products. The results show higher concentrations in the smaller specimens; this fact cannot be explained on the basis of surface adsorption, but is probably related to the ingestion of food. Dissection results show that the distribution of /sup 210/Po in euphausiids is not homogeneous, but that the majority is concentrated in the internal organs, the alimentary tract and the hepatopancreas in particular. The natural radiation dose received by these organs is in consequence much higher than that received by the whole animal. Use of a dynamic model allowed the flux of /sup 210/Po through M. norvegica to be calculated. The calculations confirm that food is the principal source of /sup 210/Po for this species, and clearly show that fecal pellets constitute the major elimination route. Extrapolation of the data to zooplankton in general leads to the conclusion that zooplankton metabolic activity plays an important role in transporting /sup 210/Po from the surface layers of the ocean to depth. (auth)

  2. Metabolic balances of 210Pb and 210Po at natural levels

    International Nuclear Information System (INIS)

    Spencer, H.; Holtzman, R.B.; Kramer, L.; Ilcewicz, F.H.

    1977-01-01

    Metabolic balances of 210 Po and 210 Pb were determined under strictly controlled dietary conditions in adult males. The intakes of the two nuclides were due to the dietary contents of these radioisotopes, inhalation from the atmosphere, and smoking of cigarettes. No additional radioisotope was given. The mean dietary intake of 210 Pb was 1.25 pCi/day and of 210 Po, 1.63 pCi/day. The major pathway of excretion of both nuclides is via the gastrointestinal tract and the urinary excretion is much lower. The total excretions of 210 Pb and 210 Po were greater than the dietary intake and the overall balances were -0.28 and -0.16 pCi/day for the two nuclides, respectively, during a low calcium intake. The 210 Pb balances did not change significantly when the calcium intake was increased 7- to 10-fold except for one patient in whom the balance became more negative. The 210 Po balance was more negative during calcium intakes of 800 and 2200 mg than during a low calcium intake of 200 mg/day. The urinary and fecal excretions of the two radionuclides were not affected by the intake of sodium fluoride, while the diuretic compound Hydrodiuril appeared to decrease the fecal 210 Pb excretion

  3. Metabolic balances of 210Pb and 210Po at natural levels

    International Nuclear Information System (INIS)

    Spencer, H.; Holtzman, R.B.; Kramer, L.; Ilcewicz, F.H.

    1977-01-01

    Metabolic balances of 210 Po and 210 Pb were determined under strictly controlled dietary conditions in adult males. The intakes of the two nuclides were due to the dietary contents of these radioisotopes, inhalation from the atmosphere, and smoking of cigarettes. No additional radioisotope was given. The mean dietary intake of 210 Pb was 1.25 pCi/day and of 210 Po, 1.63 pCi/day. The major pathway of excretion of both nuclides is via the gastrointestinal tract; the urinary excretion is much lower. The total excretions of 210 Pb and 210 Po were greater than the dietary intake and the overall balances were -0.28 and -0.16 pCi/day for the two nuclides, respectively, during a low calcium intake. The 210 Pb balances did not change significantly when the calcium intake was increased 7- to 10-fold except for one patient in whom the balance became more negative. The 210 Po balance was more negative during calcium intakes of 800 and 2200 mg than during a low calcium intake of 200 mg/day. The urinary and fecal excretions of the two radionuclides were not affected by the intake of sodium fluoride, while the diuretic compound, Hydrodiuril, appeared to decrease the fecal 210 Pb excretion

  4. Levels and transfer of 210Po and 210Pb in Nordic terrestrial ecosystems

    International Nuclear Information System (INIS)

    Brown, J.E.; Gjelsvik, R.; Roos, P.; Kalas, J.A.; Outola, I.; Holm, E.

    2011-01-01

    Recent developments regarding environmental impact assessment methodologies for radioactivity have precipitated the need for information on levels of naturally occurring radionuclides within and transfer to wild flora and fauna. The objectives of this study were therefore to determine activity concentrations of the main dose forming radionuclides 210 Po and 210 Pb in biota from terrestrial ecosystems thus providing insight into the behaviour of these radioisotopes. Samples of soil, plants and animals were collected at Dovrefjell, Central Norway and Olkiluoto, Finland. Soil profiles from Dovrefjell exhibited an approximately exponential fall in 210 Pb activity concentrations from elevated levels in humus/surface soils to 'supported' levels at depth. Activity concentrations of 210 Po in fauna (invertebrates, mammals, birds) ranged between 2 and 123 Bq kg -1 d.w. and in plants and lichens between 20 and 138 Bq kg -1 d.w. The results showed that soil humus is an important reservoir for 210 Po and 210 Pb and that fauna in close contact with this media may also exhibit elevated levels of 210 Po. Concentration ratios appear to have limited applicability with regards to prediction of activity concentrations of 210 Po in invertebrates and vertebrates. Biokinetic models may provide a tool to explore in a more mechanistic way the behaviour of 210 Po in this system.

  5. Levels and transfer of {sup 210}Po and {sup 210}Pb in Nordic terrestrial ecosystems

    Energy Technology Data Exchange (ETDEWEB)

    Brown, J.E., E-mail: justin.brown@nrpa.n [Norwegian Radiation Protection Authority, PO Box 55, N-1332, Osteras (Norway); Gjelsvik, R. [Norwegian Radiation Protection Authority, PO Box 55, N-1332, Osteras (Norway); Roos, P. [RISO-DTU P.O. Box 49 DK-4000 Roskilde (Denmark); Kalas, J.A. [Norwegian Institute for Nature Research (NINA), Tungasletta 2, 7485 Trondheim (Norway); Outola, I. [STUK, Laippatie 4/P.O. BOX 14, 00881 Helsinki (Finland); Holm, E. [Norwegian Radiation Protection Authority, PO Box 55, N-1332, Osteras (Norway)

    2011-05-15

    Recent developments regarding environmental impact assessment methodologies for radioactivity have precipitated the need for information on levels of naturally occurring radionuclides within and transfer to wild flora and fauna. The objectives of this study were therefore to determine activity concentrations of the main dose forming radionuclides {sup 210}Po and {sup 210}Pb in biota from terrestrial ecosystems thus providing insight into the behaviour of these radioisotopes. Samples of soil, plants and animals were collected at Dovrefjell, Central Norway and Olkiluoto, Finland. Soil profiles from Dovrefjell exhibited an approximately exponential fall in {sup 210}Pb activity concentrations from elevated levels in humus/surface soils to 'supported' levels at depth. Activity concentrations of {sup 210}Po in fauna (invertebrates, mammals, birds) ranged between 2 and 123 Bq kg{sup -1} d.w. and in plants and lichens between 20 and 138 Bq kg{sup -1} d.w. The results showed that soil humus is an important reservoir for {sup 210}Po and {sup 210}Pb and that fauna in close contact with this media may also exhibit elevated levels of {sup 210}Po. Concentration ratios appear to have limited applicability with regards to prediction of activity concentrations of {sup 210}Po in invertebrates and vertebrates. Biokinetic models may provide a tool to explore in a more mechanistic way the behaviour of {sup 210}Po in this system.

  6. A cost effective method for the determination of 210Po and 210Pb in environmental materials

    International Nuclear Information System (INIS)

    Clayton, R.F.; Bradley, E.J.

    1995-01-01

    The majority of the methods for the determination of 210 Pb and 210 Po in environmental materials were developed in the 1960s. However, with the advances in technology since that time, particularly in the areas of ion-exchange chromatography and instrumentation, new methods may be more appropriate to measure these radionuclides in environmental media such as foodstuffs. A review was conducted of potentially suitable methods. Four methods were selected for detailed evaluation on the basis of cost and sensitivity. A cheap, sensitive and simple method is recommended for the analysis of 210 Pb and 210 Po in environmental materials

  7. Determination of internal radiation dose due to intake of polonium 210 and lead 210 via smoking

    International Nuclear Information System (INIS)

    Al-Masri, M. S.; Kharita, M.H.; Nashawati, A.; Amin, Y.; Al-Akel, B.

    2004-12-01

    In this study, 18 kind of cigarettes and five kinds of molasses consumed by Syrians were collected and analyzed for radioactivity in order to estimate the internal radiation dose caused by 210 Po and 210 Pb intake. Polonium 210 and lead 210 concentrations varied between 4 and 16.4 m Bq/cigarette, while 210 Po distribution ratios in different parts of consumed cigarette were %12, %73, %1.6 in ash, smoke and filter, respectively. In addition, annual intake of 210 Po by a main smoker was varied between 4.4 and 18 Bq/year assuming that the main smoker breathes about 15% of the total 210 Po present in tobacco. Using the values of the annual intake, annual equivalent radiation dose caused by smoking has reached 178 μSv/year. Moreover, mean concentration of 210 Po in nonsmokers and smokers bloods has reached 130 and 97 mBq/l, respectively, while the mean value of 210 Po concentration was relatively higher and reached 176 and 155 mBq/l in smokers and non smoker bloods, respectively (Authors)

  8. Levels of /sup 209/Tl and /sup 211/Pb populated in the /sup 210/Pb(t,. cap alpha. )/sup 209/Tl and /sup 210/Pb(t,d)/sup 211/Pb reactions. [J,. pi.

    Energy Technology Data Exchange (ETDEWEB)

    Ellegaard, C; Barnes, P D [Carnegie-Mellon Univ., Pittsburgh, Pa. (USA); Flynn, E R [Los Alamos Scientific Lab., N.Mex. (USA)

    1976-03-22

    The reactions /sup 210/Pb(t,..cap alpha..)/sup 209/Tl and /sup 210/Pb(t,d)/sup 211/Pb have been studied with 20 MeV tritons. Seven levels in /sup 209/Tl have been identified in the /sup 210/Pb(t,..cap alpha..)/sup 209/Tl reaction. Level spins have been suggested by comparing the observed spectrum with that of the corresponding reaction on /sup 208/Pb. Nineteen levels in /sup 211/Pb were identified in the /sup 210/Pb(t,d)/sup 211/Pb reaction. Angular distributions were measured and lsub(n) values and spectroscopic factors were extracted by DWBA calculations. In both cases the spectra are very similar to the spectra obtained with /sup 208/Pb as a target. The deviations from these simple spectra would appear to be amenable to a description in terms of a coupling of the extra particle or hole to the /sup 210/Pb core.

  9. Evaluation of uncertainty and detection limits in 210Pb and 210Po measurement in water by alpha spectrometry using 210Po spontaneous deposition onto a silver disk

    International Nuclear Information System (INIS)

    Fernández, Pedro L.; Gómez, José; Ródenas, Carmen

    2012-01-01

    An easy and accurate method for the determination of 210 Pb and 210 Po in water using 210 Po spontaneous deposition onto a silver disk is proposed and assessed for its detection capabilities according to the ISO Guide for the expression of uncertainty in measurement (GUM) and ISO Standard 11929-7 concerning the evaluation of the characteristic limits for ionizing radiation measurements. The method makes no assumption on the initial values of the activity concentrations of 210 Pb, 210 Bi and 210 Po in the sample to be analyzed, and is based on the alpha spectrometric measurement of 210 Po in two different aliquots: the first one measured five weeks after the sampling date to ensure radioactive equilibrium between 210 Pb and 210 Bi and the second after a sufficient time for the ingrowth of 210 Po from 210 Pb to be significant. As shown, for a recommended time interval of seven months between 210 Po measurements, the applicability of the proposed method is limited to water samples with a 226 Ra to 210 Pb activity ratio C Ra /C Pb ≤4, as usual in natural waters. Using sample and background counting times of 24 h and 240 h, respectively, the detection limit of the activity concentration of each radionuclide at the sampling time for a 1 L sample typically varies between 0.7 and 16 mBq L −1 for 210 Pb in water samples with an initial activity of 210 Po in the range 0–200 mBq L −1 , and between 0.6 and 8.5 mBq L −1 for 210 Po in water samples with an initial activity of 210 Pb in the same range. - Highlights: ► 210 Pb and 210 Po measurement in water by 210 Po spontaneous deposition onto silver disks. ► 210 Pb and 210 Po determination based on 210 Po measurement in two different aliquots. ► Evaluation of characteristic limits in radioactivity measurements using ISO 11929-7. ► 10 Pb - 210 Po detection limits decrease with time elapsed between 210 Po measurements.

  10. Localization and Related Phenomena in Multiply Connected Nanostructured Inverse Opal Bismuth

    Science.gov (United States)

    Bleiweiss, Michael; Saygi, Salih; Amirzadeh, Jafar; Datta, Timir; Lungu, Anca; Yin, Ming; Palm, Eric; Brandt, Bruce; Iqbal, Zafar

    2001-03-01

    The nanostructures were fabricated by pressure infiltration of bismuth into porous artificial opal and were characterized using SEM, EDX and XRD. These structures form a regular three-dimensional network in which the bismuth regions percolate in all directions between the close packed spheres of SiO_2. The sizes of the conducting regions are of the order of tens of nanometers. The static magnetic properties of both bismuth inverse opal and bulk bismuth were studied using a SQUID magnetometer. Transport measurements, including Hall, were done using standard ac four and six probe techniques in fields up to 17 T* and temperatures between 4.2 and 150 K. The results of these measurements, including the observation of localization phenomena, will be discussed. Comparisons will be made with published results on bismuth nanowires. *Performed at the National High Magnetic Field Lab (NHMFL) FSU, Tallahassee, FL. Partially supported by a grant from NASA.

  11. An improved method for the separation of 210Bi and 210Po from 210Pb by using solid-phase extraction disk membranes: environmental applications

    International Nuclear Information System (INIS)

    Marley, N.A.; Gaffney, J.S.; Orlandini, K.A.; Cunningham, M.M.; Drayton, P.J.

    1999-01-01

    An improved method is described for the rapid separation of 210 Bi and 210 Po from the parent radionuclide, 210 Pb, in environmental samples. After the metals were leached from a variety of matrices, they were converted to their anionic chloride complexes by addition of 1 M HCl. These complexes can be separated by solid-phase extraction with disk extraction membranes impregnated with anionic chelating particles. This separation technique takes advantage of the differences in sorption behavior of the chloride complexes to strongly basic anion exchange groups. The extraction membranes can then be counted directly for 210 Bi and 210 Po. If sufficient time is allowed for ingrowth of the daughter, the concentration of the parent 210 Pb in the original sample can be determined from the concentration of 210 Bi. In addition, the ratios of 210 Bi/ 210 Pb and 210 Po/ 210 Pb can be obtained by immediate extraction of 210 Bi followed by ingrowth of 210 Bi for a second determination to establish 210 Pb concentration levels. This can be accomplished easily in order to estimate the residence times of atmospheric aerosols or aqueous colloidal materials. This new technique avoids the time consuming extraction, precipitation, and electroplating procedures used previously and eliminates the experimental errors associated with multiple sample manipulations. (orig.)

  12. DOSE210, A Semi-empirical Model for Prediction of Organ Distribution and Radiation Doses from Long Term Exposure to 210Pb and 210Po

    International Nuclear Information System (INIS)

    Salmon, P.L.; Bondarenko, O.A.; Henshaw, D.L.

    1999-01-01

    The DOSE210 model is an internal dosimetric model for 210 Pb and 210 Po which is based on current ICRP generic models. It is constrained and validated by reference to up-to-date published biokinetic data for both nuclides. The model has been validated primarily in regard to the relation between levels of chronic lifetime intake and organ concentrations of 210 Pb and 210 Po. To this end some adjustments to current ICRP biokinetic parameters have been made. The most substantial changes have been made to bone surface biokinetics of 210 Pb and 210 Po to reflect recent experimental studies on the microdistribution and radioactive equilibrium of these nuclides in bone, as well as measurements in biopsied human red bone marrow. An important dosimetric prediction of DOSE210 is a substantially lower dose to skeletal tissues from internal 210 Pb and 210 Po than that predicted by the current ICRP model. The most significant dose component predicted from lifetime environmental exposure to 210 Pb and 210 Po is the alpha dose to liver and kidney in infancy. Recycling of historic intakes of 210 Pb in the adult, principally from bone, is calculated to account for 22% of 210 Pb present in the plasma. (author)

  13. Sup(210)Pb and 210Po distributions and disequilibrium in the coastal and shelf waters of the southern North Sea

    International Nuclear Information System (INIS)

    Zhizheng, Zuo; Eisma, Doeke

    1993-01-01

    Concentration profiles of 210 Pb and 210 Po were measured at 10 stations in the coastal and shelf areas of the southern North Sea. Scavenging processes in this study area are revealed by 210 Po/ 210 Pb disequilibrium and their distributions in the water column. Results for 210 Po show strong excess, relative to 210 Pb, in both dissolved and particulate forms, indicating an additional flux of 210 Po from the coastal and shelf sediment. A significant maximum of the dissolved 210 Po and 210 Pb over the fine grained depositional area (Oyster Ground) was observed to correspond with resuspension of the underlying muddy sediments. A comparison of the data between the water and sediment columns shows that the excess of 210 Po found in the water body could be balanced by only a small amount of deficit of 210 Po in the sediment, due to the characteristics of this continental shelf area. (author)

  14. Unusually large 210Po deficiencies relative to 210Pb in the Kuroshio Current of the East China and Philippine seas

    International Nuclear Information System (INIS)

    Yoshiyuki Nozaki; Naoko Ikuta; Mayumi Yashima

    1990-01-01

    Three vertical water profiles of 210 Pb and 210 Po have been measured in the East China and Philippine seas. All the profiles show a large 210 Po deficiency of ∼ 8 dpm/cm 2 relative to 210 Pb in the top ∼ 1,000 m of the water column. Based on the 210 Po deficiency, the steady state flux for 210 Po removal from the surface water is estimated to be 14 dpm cm -2 /yr. The 210 Po/ 210 Pb ratio of sinking particles will be too high unless an additional source of 210 Pb into the surface is accounted for. Thus the large 210 Po deficit is probably caused by the increased atmospheric input of 210 Pb without any significant 210 Po, which is focused in the Kuroshio region by isopycnal transport, and the preferential scavenging of 210 Po relative to 210 Pb by settling particles. The transient model calculations indicate that the model can account for the observed high excess 210 Pb inventory and large 210 Po deficiency in the water column if focusing of atmospherically derived 210 Pb in the Kuroshio water is a factor of 2-3 more than the local input. Such lateral redistribution by the western North Pacific gyre circulation is not inconsistent with the deeper penetration and the high water column inventories of anthropogenic substances observed in this region

  15. Thermodynamics Calculation and Experimental Study on Separation of Bismuth from a Bismuth Glance Concentrate Through a Low-Temperature Molten Salt Smelting Process

    Science.gov (United States)

    Yang, Jian-Guang; He, De-Wen; Tang, Chao-Bo; Chen, Yong-Ming; Sun, Ya-Hui; Tang, Mo-Tang

    2011-08-01

    The main purpose of this study is to characterize and separate bismuth from a bismuth glance concentrate through a low-temperature, sulfur-fixing smelting process. This article reports on a study conducted on the optimization of process parameters, such as Na2CO3 and zinc oxide wt pct in charging, smelting temperature, smelting duration on the bismuth yield, resultant crude bismuth grade, and sulfur-fixing rate. A maximum bismuth recovery of 97.31 pct, crude bismuth grade of 96.93 pct, and 98.23 pct sulfur-fixing rate are obtained when a charge (containing 63.50 wt pct of Na2CO3 and 22.50 wt pct of bismuth glance, as well as 5 pct in excess of the stoichiometric requirement of zinc oxide dosage) is smelted at 1000 K (727 °C) for 150 minutes. This smelting operation is free from atmospheric pollution because zinc oxide is used as the sulfur-fixing agent, which can capture sulfur from bismuth sulfide and form the more thermodynamic-stable compound, zinc sulfide. The solid residue is subjected to a mineral dressing operation to obtain suspension, which is filtered to produce a cake, representing the solid particles of zinc sulfide. Based on the results of the chemical content analysis of the as-resultant zinc sulfide, more than 93 pct zinc sulfide can be recovered, and the recovered zinc sulfide grade can reach 60.20 pct. This material can be sold as zinc sulfide concentrate or roasted to be regenerated as zinc oxide.

  16. Bioavailability and chronic toxicity of bismuth citrate to earthworm Eisenia andrei exposed to natural sandy soil.

    Science.gov (United States)

    Omouri, Zohra; Hawari, Jalal; Fournier, Michel; Robidoux, Pierre Yves

    2018-01-01

    The present study describes bioavailability and chronic effects of bismuth to earthworms Eisenia andrei using OECD reproduction test. Adult earthworms were exposed to natural sandy soil contaminated artificially by bismuth citrate. Average total concentrations of bismuth in soil recovered by HNO 3 digestion ranged from 75 to 289mg/kg. Results indicate that bismuth decreased significantly all reproduction parameters of Eisenia andrei at concentrations ≥ 116mg/kg. However, number of hatched cocoons and number of juveniles seem to be more sensitive than total number of cocoons, as determined by IC 50 ; i.e., 182, 123 and > 289mg/kg, respectively. Bismuth did not affect Eisenia andrei growth and survival, and had little effect on phagocytic efficiency of coelomocytes. The low immunotoxicity effect might be explained by the involvement of other mechanisms i.e. bismuth sequestered by metal-binding compounds. After 28 days of exposure bismuth concentrations in earthworms tissue increased with increasing bismuth concentrations in soil reaching a stationary state of 21.37mg/kg dry tissue for 243mg Bi/kg dry soil total content. Data indicate also that after 56 days of incubation the average fractions of bismuth available extracted by KNO 3 aqueous solution in soil without earthworms varied from 0.0051 to 0.0229mg/kg, while in soil with earthworms bismuth concentration ranged between 0.310-1.347mg/kg dry soil. We presume that mucus and chelating agents produced by earthworms and by soil or/and earthworm gut microorganisms could explain this enhancement, as well as the role of dermal and ingestion routes of earthworms uptake to soil contaminant. Copyright © 2017 Elsevier Inc. All rights reserved.

  17. Bismuth oxide nanotubes-graphene fiber-based flexible supercapacitors

    Science.gov (United States)

    Gopalsamy, Karthikeyan; Xu, Zhen; Zheng, Bingna; Huang, Tieqi; Kou, Liang; Zhao, Xiaoli; Gao, Chao

    2014-07-01

    Graphene-bismuth oxide nanotube fiber as electrode material for constituting flexible supercapacitors using a PVA/H3PO4 gel electrolyte is reported with a high specific capacitance (Ca) of 69.3 mF cm-2 (for a single electrode) and 17.3 mF cm-2 (for the whole device) at 0.1 mA cm-2, respectively. Our approach opens the door to metal oxide-graphene hybrid fibers and high-performance flexible electronics.Graphene-bismuth oxide nanotube fiber as electrode material for constituting flexible supercapacitors using a PVA/H3PO4 gel electrolyte is reported with a high specific capacitance (Ca) of 69.3 mF cm-2 (for a single electrode) and 17.3 mF cm-2 (for the whole device) at 0.1 mA cm-2, respectively. Our approach opens the door to metal oxide-graphene hybrid fibers and high-performance flexible electronics. Electronic supplementary information (ESI) available: Equations and characterization. SEM images of GGO, XRD and XPS of Bi2O3 NTs, HRTEM images and EDX Spectra of Bi2O3 NT5-GF, CV curves of Bi2O3NT5-GF, Bi2O3 NTs and bismuth nitrate in three-electrode system (vs. Ag/AgCl). CV and GCD curves of Bi2O3 NT1-GF and Bi2O3 NT3-GF. See DOI: 10.1039/c4nr02615b

  18. Conduction mechanism in bismuth silicate glasses containing titanium

    International Nuclear Information System (INIS)

    Dult, Meenakshi; Kundu, R.S.; Murugavel, S.; Punia, R.; Kishore, N.

    2014-01-01

    Bismuth silicate glasses mixed with different concentrations of titanium dioxide having compositions xTiO 2 –(60−x)Bi 2 O 3 –40SiO 2 with x=0, 5, 10, 15 and 20 were prepared by the normal melt quench technique. The frequency dependence of the ac electrical conductivity of different compositions of titanium bismuth silicate glasses has been studied in the frequency range 10 −1 Hz to 10 MHz and in the temperature range 623–703 K. The temperature and frequency dependent conductivity is found to obey Jonscher's universal power law for all the compositions of titanium bismuth silicate glass system. The dc conductivity (σ dc ), so called crossover frequency (ω H ), and frequency exponent (s) have been estimated from the fitting of experimental data of ac conductivity with Jonscher's universal power law. Enthalpy to dissociate the cation from its original site next to a charge compensating center (H f ) and enthalpy of migration (H m ) have also been estimated. The conductivity data have been analyzed in terms of different theoretical models to determine the possible conduction mechanism. Analysis of the conductivity data and the frequency exponent shows that the correlated barrier hopping of electrons between Ti 3+ and Ti 4+ ions in the glasses is the most favorable mechanism for ac conduction. The temperature dependent dc conductivity has been analyzed in the framework of theoretical variable range hopping model (VRH) proposed by Mott which describe the hopping conduction in disordered semiconducting systems. The various polaron hopping parameters have also been deduced. Mott's VRH model is found to be in good agreement with experimental data and the values of inverse localization length of s-like wave function (α) obtained by this model with modifications suggested by Punia et al. are close to the ones reported for a number of oxide glasses

  19. Yttrium bismuth titanate pyrochlore mixed oxides for photocatalytic hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Merka, Oliver

    2012-10-18

    In this work, the sol-gel synthesis of new non-stoichiometric pyrochlore titanates and their application in photocatalytic hydrogen production is reported. Visible light response is achieved by introducing bismuth on the A site or by doping the B site by transition metal cations featuring partially filled d orbitals. This work clearly focusses on atomic scale structural changes induced by the systematical introduction of non-stoichiometry in pyrochlore mixed oxides and the resulting influence on the activity in photocatalytic hydrogen production. The materials were characterized in detail regarding their optical properties and their atomic structure. The pyrochlore structure tolerates tremendous stoichiometry variations. The non-stoichiometry in A{sub 2}O{sub 3} rich compositions is compensated by distortions in the cationic sub-lattice for the smaller Y{sup 3+} cation and by evolution of a secondary phase for the larger Bi{sup 3+} cation on the A site. For TiO{sub 2} rich compositions, the non-stoichiometry leads to a special vacancy formation in the A and optionally O' sites. It is shown that pyrochlore mixed oxides in the yttrium bismuth titanate system represent very active and promising materials for photocatalytic hydrogen production, if precisely and carefully tuned. Whereas Y{sub 2}Ti{sub 2}O{sub 7} yields stable hydrogen production rates over time, the bismuth richer compounds of YBiTi{sub 2}O{sub 7} and Bi{sub 2}Ti{sub 2}O{sub 7} are found to be not stable under irradiation. This drawback is overcome by applying a special co-catalyst system consisting of a precious metal core and a Cr{sub 2}O{sub 3} shell on the photocatalysts.

  20. Determination of 210Pb and 210Po in Brazilian cigarette tobacco

    International Nuclear Information System (INIS)

    Peres, A.C.; Hiromoto, G.

    2000-01-01

    Cigarette smoking is one of the important pathways that could contribute to enhance the radiation dose to man, due to the relatively large concentrations of 210 Pb and 210 Po found in tobacco leaves. In this work, concentrations of these two radionuclides were determined in eight of the most commercialized cigarette brands produced in Brazil. The samples analyzed were bought randomly in the market. The 210 Pb was determined by counting the beta activity of the 210 Bi in a gas flow proportional detector, after radiochemical separation and precipitation of the PbCrO 4 . The 210 Po was determined by alpha spectrometry, using a surface barrier detector, after radiochemical separation and spontaneous deposition of Po in copper disk. The results showed concentrations ranging from 15,8 to 30,2 mBq per gram of dry tobacco for 210 Pb and from 18,8 to 27,4 mBq per gram of dry tobacco for 210 Po. Taking in account the experimental error of the measurements, radioactive equilibrium between 210 Pb and 210 Po is observed for all analyzed samples. This result was expected, since the delayed time from the harvest of tobacco leaves to the introduction of cigarettes in the market is enough to reach that equilibrium. Assuming a 20 cigarettes per day consumption, and a 10% of Pb and 20% of Po being inhaled by the primary smokers, it is obtained a value of yearly intake of 11,3 Bq of 210 Pb and 21,2 Bq of 210 Po, due to cigarette consumption. These values lead to an increment to the committed effective dose of 0,025 mSv year -1 and an increment to the probability of getting cancer of 1 x 10 -6 per year. (author)

  1. Solution combustion synthesis and characterization of nanosized bismuth ferrite

    Science.gov (United States)

    Sai Kumar, V. Sesha; Rao, K. Venkateswara; Krishnaveni, T.; Kishore Goud, A. Shiva; Reddy, P. Ranjith

    2012-06-01

    The present paper describes a simple method of nanosized BiFeO3 by the solution combustion synthesis using bismuth and iron nitrates as oxidizers and the combination fuel of citric acid and ammonium hydroxide, with fuel to oxidizer ratio (Ψ = 1) one. The X-ray Diffraction results indicated rhombohedral phase (R3m) with JCPDS data card no: 72-2035. The ferroelectric transition of the sample at 8310C was detected by differential thermal analysis. Thermal analysis was done by Thermal gravimetric-Differential thermal analyzer and obtained results were presented in this paper.

  2. miR-210 inhibits trophoblast invasion and is a serum biomarker for preeclampsia.

    Science.gov (United States)

    Anton, Lauren; Olarerin-George, Anthony O; Schwartz, Nadav; Srinivas, Sindhu; Bastek, Jamie; Hogenesch, John B; Elovitz, Michal A

    2013-11-01

    Preeclampsia is characterized by hypertension and proteinuria in pregnant women. Its exact cause is unknown. Preeclampsia increases the risk of maternal and fetal morbidity and mortality. Although delivery, often premature, is the only known cure, early targeted interventions may improve maternal and fetal outcomes. Successful intervention requires a better understanding of the molecular etiology of preeclampsia and the development of accurate methods to predict women at risk. To this end, we tested the role of miR-210, a miRNA up-regulated in preeclamptic placentas, in first-trimester extravillous trophoblasts. miR-210 overexpression reduced trophoblast invasion, a process necessary for uteroplacental perfusion, in an extracellular signal-regulated kinase/mitogen-activated protein kinase-dependent manner. Conversely, miR-210 inhibition promoted invasion. Furthermore, given that the placenta secretes miRNAs into the maternal circulation, we tested if serum expression of miR-210 was associated with the disease. We measured miR-210 expression in two clinical studies: a case-control study and a prospective cohort study. Serum miR-210 expression was significantly associated with a diagnosis of preeclampsia (P = 0.007, area under the receiver operator curves = 0.81) and was predictive of the disease, even months before clinical diagnosis (P preeclampsia that can help in identifying at-risk women for monitoring and treatment. Copyright © 2013 American Society for Investigative Pathology. Published by Elsevier Inc. All rights reserved.

  3. Technologically enhanced 210Pb and 210Po in iron and steel industry

    International Nuclear Information System (INIS)

    Khater, Ashraf E.M.; Bakr, Wafaa F.

    2011-01-01

    Iron and steel manufacture has been ranked as the largest industrial source of environmental contamination in the USA; the wastes generated in their production processes contain heavy elements that can be a source of contamination, and natural radionuclides that can produce an occupational and/or public radiological impact. In this work the potential occupational effective dose rate (μSv/y) due to inhalation in four integrated steel-making factories from Egypt has been evaluated, by assuming a well defined scenario and with basis in the 210 Pb and 210 Po activity concentrations determined in ore and wastes collected in the aforementioned factories. Activity concentrations, in Bq/kg, of 210 Pb and 210 Po, and leachable Pb and Fe were measured using gamma-ray spectrometry based on HPGe detector, alpha particle spectrometry based on PIPS detector, and inductively coupled plasma-mass spectrometry (ICP-MS). Levels of 210 Pb and 210 Po in the range of 210 Pb and 210 Po radionuclides. → Both radionuclides are enriched through the thermal processes. → For radiation dose assessment inhalation would be the main route of exposure.

  4. 210Pb and 210Po determination in environmental samples using liquid scintillation counting and alpha spectrometry

    International Nuclear Information System (INIS)

    Perez Sanchez, D.; Martin Sanchez, A.; Jurado Vargas, M.

    2003-01-01

    A simple radiochemical procedure has been developed to determine 210 Pb and 210 Po in environmental samples from the same matrix. Sediment samples are decomposed by leaching with mineral acids or by microwave digestion, while water samples are pre-concentrated. One part of the resulting solution, spiked with 209 Po, is used for 210 Po determination by spontaneous deposition onto nickel disks (a-spectrometry). The other part is assayed for 210 Pb, separating the Pb either by anion-exchange (sediment samples), or by solvent extraction (water samples). The 210 Pb source is finally prepared by precipitation as oxalate and the chemical recovery determined by gravimetry. The 210 Pb activity concentration is determined by liquid scintillation. A standard sediment sample supplied by IAEA and spiked water samples were analysed to check the procedure. The 210 Pb and 210 Po measurements agreed well with the certifications, deviations being less than 10%. The mean recoveries for Pb and Po were (70±12)% and (77±8)% for sediments, and (70±10)% and (81±7)% for waters, respectively. (author)

  5. Unusual 210Po/210Pb ratios in the surface water of the Gulf of Lions

    International Nuclear Information System (INIS)

    Radakovitch, O.; Heussner, S.; Cherry, R.D.; Heyraud, M.

    1998-01-01

    Concentrations of 210 Po and 210 Pb have been measured in sea water collected in the Grand Rhone Canyon. Concentrations of 210 Pb are at similar levels to those found in other Mediterranean sea water samples, and are at the levels which would be expected in comparison with global sea water data. The same applies to the 210 Po concentrations in samples from below 100 m depth. Surface samples from above 100 m have 210 Po at levels rather higher than expected, and their 210 Po/ 210 Pb ratios are about 1 or more as compared with the usual open ocean ratio 0.5. These data can be interpreted as indicating another source of supply of 210 Po to the surface layer in addition to the normal atmospheric input. We suggest that an episodic advective particulate input, probably originating in the output of the Rhone river and perhaps involving resuspension of fine particulates from the bottom sediments as a result of storm conditions, is he most likely candidate for this additional source. (authors)

  6. Distribution of lead-210 and polonium-210 between soluble and particulate phases in seawater

    International Nuclear Information System (INIS)

    Spencer, D.W.

    1975-01-01

    Results are reported from radiometric measurements of the distribution of 210 Pb and 210 Po in surface seawater and suspended particulate matter. Samples of plankton and sediments collected from some locations were also analyzed. Samples of seawater and suspended particulate matter were collected from stations located in the Gulf of Maine, the North Atlantic, and approximately 500 miles southwest of Gilbraltar. (U.S.)

  7. Natural concentrations of Pb/sup 210/ and Po/sup 210/ in plants of steppe phytocoenoses

    Energy Technology Data Exchange (ETDEWEB)

    Ladinskaya, L A; Parfenov, Yu D; Arutyunov, P S; Popov, D K [Leningradskij Inst. Radiatsionnoj Gigieny (USSR)

    1976-01-01

    Data are presented on the concentration of /sup 210/Pb and /sup 210/Po in summer vegetation in the aerial and root parts of sown fodder crops from steppes, saline meadows and marshy meadows and also in the leaves and branches of trees and bushes. The average concentrations of /sup 110/Pb and /sup 210/Po in the plants of individual communities have been evaluated, together with the /sup 210/Po//sup 210/Pb ratios in the aerial parts and roots and the accumulation coefficients. The variation distribution of the /sup 210/Po and /sup 210/Pb concentrations follows a log-normal law.

  8. Research on the behavior of polonium produced in lead-bismuth eutectic irradiated with neutrons. JAERI's nuclear research promotion program, H10-026. Contract research

    International Nuclear Information System (INIS)

    Sekimoto, Hiroshi; Igashira, Masayuki; Yano, Toyohiko; Obara, Toru; Ohsaki, Toshiro

    2002-03-01

    Lead-Bismuth Eutectic (LBE) is proposed by several research institutes as a coolant of liquid metal cooled fast reactors, instead of sodium, and a target of accelerator driven subcritical nuclear reactor systems (ADS). LBE has some advantages that it is chemically inert compared to sodium and that its melting point is low like sodium. A problem might be that bismuth produces polonium, which is an alpha emitter, by irradiation of neutrons. The purpose of the study is to get information for quantitative estimations of the release of polonium on LBE cooled fast reactors and on ADSs by making it clear about production rate of polonium (information about cross section) by neutron irradiation of LBE, release rate of the produced polonium from LBE, and adsorption rate of the polonium on various materials. To get the information about production rate of polonium, neutron cross sections of bismuth were measured in keV energy region, which was important in fast reactors, by using the Pelletron accelerator in Research Laboratory for Nuclear Reactors, Tokyo Institute of Technology. The obtained neutron capture cross sections were from 1/2 to 1/3 of the evaluated values in JENDL and the obtained polonium production cross sections were almost 1/3 of it. At the same time, an experimental device was designed for heating and adsorption experiments and the performance was tested. The performance of alpha spectrometer was tested also. By those the method was established for the measurement of polonium released from melted LBE after neutron irradiation. (author)

  9. Radioactive {sup 210}Po in magnesium supplements

    Energy Technology Data Exchange (ETDEWEB)

    Struminska-Parulska, Dagmara Ida [Gdansk Univ. (Poland). Environmental Chemistry and Radiochemistry Chair

    2016-08-01

    The aim of this pioneer study was to determine polonium {sup 210}Po in the most popular magnesium supplements in Poland and estimate the possible related dose assessment to the consumers. The analyzed magnesium pharmaceutics contained organic or inorganic magnesium compounds; some from natural sources. The objectives of this research were to investigate the naturally occurring {sup 210}Po activity concentrations in magnesium supplements, find the correlations between {sup 210}Po concentration in medicament and magnesium chemical form, and calculate the effective radiation dose connected to analyzed magnesium supplement consumption. The highest {sup 210}Po activity concentrations were determined in mineral tablets made from sedimentary rocks, namely dolomite - 3.84 ± 0.15 mBq g{sup -1} (sample Mg17). The highest annual radiation dose from {sup 210}Po taken with 1 tablet of magnesium supplement per day or with 400 mg of pure Mg daily would come from sample Mg17 (dolomite) - 1.35 ± 0.5 and 8.44 ± 0.33 μSv year{sup -1} respectively.

  10. Radioactive 210Po in magnesium supplements

    International Nuclear Information System (INIS)

    Struminska-Parulska, Dagmara Ida

    2016-01-01

    The aim of this pioneer study was to determine polonium 210 Po in the most popular magnesium supplements in Poland and estimate the possible related dose assessment to the consumers. The analyzed magnesium pharmaceutics contained organic or inorganic magnesium compounds; some from natural sources. The objectives of this research were to investigate the naturally occurring 210 Po activity concentrations in magnesium supplements, find the correlations between 210 Po concentration in medicament and magnesium chemical form, and calculate the effective radiation dose connected to analyzed magnesium supplement consumption. The highest 210 Po activity concentrations were determined in mineral tablets made from sedimentary rocks, namely dolomite - 3.84 ± 0.15 mBq g -1 (sample Mg17). The highest annual radiation dose from 210 Po taken with 1 tablet of magnesium supplement per day or with 400 mg of pure Mg daily would come from sample Mg17 (dolomite) - 1.35 ± 0.5 and 8.44 ± 0.33 μSv year -1 respectively.

  11. Handbook on lead-bismuth eutectic alloy and lead properties, materials compatibility, thermal-hydraulics and technologies

    International Nuclear Information System (INIS)

    2007-01-01

    As part of the development of advanced nuclear systems, including accelerator-driven systems (ADS) proposed for high-level radioactive waste transmutation and generation IV reactors, heavy liquid metals such as lead (Pb) or lead-bismuth eutectic (LBE) are under evaluation as reactor core coolant and ADS neutron target material. Heavy liquid metals are also being envisaged as target materials for high-power neutron spallation sources. The objective of this handbook is to collate and publish properties and experimental results on Pb and LBE in a consistent format in order to provide designers with a single source of qualified properties and data and to guide subsequent development efforts. The handbook covers liquid Pb and LBE properties, materials compatibility and testing issues, key aspects of the thermal-hydraulics and system technologies, existing test facilities, open issues and perspectives. (author)

  12. Design of an Actinide-Burning, Lead or Lead-Bismuth Cooled Reactor that Produces Low-Cost Electricity

    Energy Technology Data Exchange (ETDEWEB)

    Mac Donald, Philip Elsworth; Weaver, Kevan Dean; Davis, Cliff Bybee; MIT folks

    2000-07-01

    indirect cycle designs has investigated the effects of various parameters to increase electric production at full power. For the direct-contact reactor, major issues related to the direct-contact heat transfer rate and entrainment and carryover of liquid lead-bismuth to the turbine have been identified and analyzed. An economic analysis approach was also developed to determine the cost of electricity production in the lead-bismuth reactor. The approach will be formulated into a model and applied to develop scientific cost estimates for the different reactor designs and thus aid in the selection of the most economic option. In the area of lead-bismuth coolant activation, the radiological hazard was evaluated with particular emphasis on the direct-contact reactor. In this system, the lack of a physical barrier between the primary and secondary coolant favors the release of the alpha-emitter Po?210 and its transport throughout the plant. Modeling undertaken on the basis of the scarce information available in the literature confirmed the importance of this issue, as well as the need for experimental work to reduce the uncertainties on the basic characteristics of volatile polonium chemical forms.

  13. MicroRNA-210 Modulates Endothelial Cell Response to Hypoxia and Inhibits the Receptor Tyrosine Kinase Ligand Ephrin-A3*S⃞

    Science.gov (United States)

    Fasanaro, Pasquale; D'Alessandra, Yuri; Di Stefano, Valeria; Melchionna, Roberta; Romani, Sveva; Pompilio, Giulio; Capogrossi, Maurizio C.; Martelli, Fabio

    2008-01-01

    MicroRNAs (miRNAs) are small non-protein-coding RNAs that function as negative gene expression regulators. In the present study, we investigated miRNAs role in endothelial cell response to hypoxia. We found that the expression of miR-210 progressively increased upon exposure to hypoxia. miR-210 overexpression in normoxic endothelial cells stimulated the formation of capillary-like structures on Matrigel and vascular endothelial growth factor-driven cell migration. Conversely, miR-210 blockade via anti-miRNA transfection inhibited the formation of capillary-like structures stimulated by hypoxia and decreased cell migration in response to vascular endothelial growth factor. miR-210 overexpression did not affect endothelial cell growth in both normoxia and hypoxia. However, anti-miR-210 transfection inhibited cell growth and induced apoptosis, in both normoxia and hypoxia. We determined that one relevant target of miR-210 in hypoxia was Ephrin-A3 since miR-210 was necessary and sufficient to down-modulate its expression. Moreover, luciferase reporter assays showed that Ephrin-A3 was a direct target of miR-210. Ephrin-A3 modulation by miR-210 had significant functional consequences; indeed, the expression of an Ephrin-A3 allele that is not targeted by miR-210 prevented miR-210-mediated stimulation of both tubulogenesis and chemotaxis. We conclude that miR-210 up-regulation is a crucial element of endothelial cell response to hypoxia, affecting cell survival, migration, and differentiation. PMID:18417479

  14. Curie temperature, exchange integrals, and magneto-optical properties in off-stoichiometric bismuth iron garnet epitaxial films

    Science.gov (United States)

    Vertruyen, B.; Cloots, R.; Abell, J. S.; Jackson, T. J.; da Silva, R. C.; Popova, E.; Keller, N.

    2008-09-01

    We have studied the influence of the stoichiometry on the structural, magnetic, and magneto-optical properties of bismuth iron garnet (Bi3Fe5O12) thin films grown by pulsed laser deposition. Films with different stoichiometries have been obtained by varying the Bi/Fe ratio of the target and the oxygen pressure during deposition. Stoichiometry variations influence the Curie temperature TC by tuning the (Fe)-O-[Fe] geometry: TC increases when the lattice parameter decreases, contrary to what happens in the case of stoichiometric rare-earth iron garnets. The thermal variation of the magnetization, the Faraday rotation, and the Faraday ellipticity have been analyzed in the frame of the Néel two-sublattice magnetization model giving energies of -48K (4.1 meV), -29K (2.5 meV), and 84 K (7.3 meV) for the three magnetic exchange integrals jaa , jdd , and jad , respectively. Magneto-optical spectroscopy linked to compositional analysis by Rutherford backscattering spectroscopy shows that Bi and/or Fe deficiencies also affect the spectral variation (between 1.77 and 3.1 eV). Our results suggest that bismuth deficiency has an effect on the magneto-optical response of the tetrahedral Fe sublattice, whereas small iron deficiencies affect predominantly the magneto-optical response of the octahedral sublattice.

  15. Use of the transpiration method to study polonium evaporation from liquid lead-bismuth eutectic at high temperature

    International Nuclear Information System (INIS)

    Prieto, Borja Gonzalez; Lim, Jun; Rosseel, Kris; Bosch, Joris van den; Aerts, Alexander; Martens, Johan; Rizzi, Matthias; Neuhausen, Joerg

    2014-01-01

    Qualitative and quantitative understanding of Po volatilization under different conditions is of key importance for safety assessments of lead-bismuth eutectic (LBE) based nuclear reactors, spallation targets and accelerator driven systems. In this work we explore the possibilities of the transpiration method in combination with simple models to study the equilibrium and kinetics of Po evaporation from highly diluted solutions in lead-bismuth eutectic between 600 and 1000 C in Ar/5% H 2 and Ar. On the basis of evaporation experiments at various carrier gas flow rates, we identified the conditions of vapor saturation allowing the determination of equilibrium constants. From the limiting behavior at high flow rates, values for the maximal evaporation rate of Po from LBE were estimated. Measurements of evaporation as a function of time were consistent with the assumption that polonium dissolved in LBE obeys Henry's law. A theoretical analysis furthermore suggested that diffusion of polonium in LBE was not a rate limiting factor for evaporation under vapor saturation conditions. Newly determined values for the Henry constant of Po in LBE between 600 and 1000 C were consistent with previously derived correlations.

  16. Bismuth Silver Oxysulfide for Photoconversion Applications: Structural and Optoelectronic Properties

    KAUST Repository

    Baqais, Amal Ali Abdulallh; Curutchet, Antton; Ziani, Ahmed; Ait Ahsaine, Hassan; Sautet, Philippe; Takanabe, Kazuhiro; Le Bahers, Tangui

    2017-01-01

    Single-phase bismuth silver oxysulfide, BiAgOS, was prepared by a hydrothermal method. Its structural, morphological and optoelectronic properties were investigated and compared with bismuth copper oxysulfide (BiCuOS). Rietveld refinement of the powder X-ray diffraction (XRD) measurements revealed that the BiAgOS and BiCuOS crystals have the same structure as ZrSiCuAs: the tetragonal space group P4/nmm. X-ray photoelectron spectroscopy (XPS) analyses confirmed that the BiAgOS has a high purity, in contrast with BiCuOS, which tends to have Cu vacancies. The Ag has a monovalent oxidation state, whereas Cu is present in the oxidation states of +1 and +2 in the BiCuOS system. Combined with experimental measurements, density functional theory calculations employing the range-separated hybrid HSE06 exchange-correlation functional with spin-orbit coupling quantitatively elucidated photophysical properties such as ab-sorption coefficients, effective masses and dielectric constants. BiCuOS and BiAgOS were found to have indirect bandgaps of 1.1 and 1.5 eV, respectively. Both possess high dielectric constants and low electron and hole effective masses. Therefore, these materials are expected to have high exciton dissociation capabilities and excellent carrier diffusion properties. This study reveals that BiAgOS is a promising candidate for photoconversion applications.

  17. Synthesis and characterization of bismuth alkaline titanate powders

    Energy Technology Data Exchange (ETDEWEB)

    Torres-Huerta, A.M., E-mail: atorresh@ipn.mx [CICATA-Altamira, Instituto Politecnico Nacional, Km. 14.5 Carretera Tampico Puerto Industrial Altamira, Altamira, Tamps. 89600 (Mexico); Dominguez-Crespo, M.A. [CICATA-Altamira, Instituto Politecnico Nacional, Km. 14.5 Carretera Tampico Puerto Industrial Altamira, Altamira, Tamps. 89600 (Mexico); Hernandez-Perez, M.A. [ESIQIE, Metalurgia, Instituto Politecnico Nacional, Mexico, D. F (Mexico); Garcia-Zaleta, D.S. [CICATA-Altamira, Instituto Politecnico Nacional, Km. 14.5 Carretera Tampico Puerto Industrial Altamira, Altamira, Tamps. 89600 (Mexico); Brachetti-Sibaja, S.B. [CICATA-Altamira, Instituto Politecnico Nacional, Km. 14.5 Carretera Tampico Puerto Industrial Altamira, Altamira, Tamps. 89600 (Mexico); Instituto Tecnologico de Ciudad Madero, Av. 1o. de Mayo esq. Sor Juana Ines de la Cruz s/n Col. Los Mangos C.P.89440 Cd. Madero Tamaulipas (Mexico)

    2011-06-15

    In this work, samples of bismuth alkaline titanate, (K{sub 0.5}Na{sub 0.5}){sub (2-x/2)}Bi{sub (x/6)}TiO{sub 3}, (x = 0.05-0.75) have been prepared by conventional ceramic technique and molten salts. Metal oxides or carbonates powders were used as starting raw materials. The crystalline phase of the synthesized powders was identified by the X-ray diffraction (XRD) and particle morphology was characterized by scanning electron microscopy (SEM). Solid state reaction method was unsuccessful to obtain pellets. From XRD results, a rhombohedral structure was detected and the parameter lattice were estimated to be a = 5.5478 A and {alpha} = 59.48{sup o}. These parameters were used to refine the structure by Rietveld analysis. SEM results showed several morphologies. Apparently, bismuth is promoting the grain growth whose sizes vary from 30 nm to 180 nm It is expected that these materials can be utilized in practical applications as substitutes for lead zirconatetitanate (PZT)-based ceramics.

  18. Angle Dependence of the Orbital Magnetoresistance in Bismuth

    Directory of Open Access Journals (Sweden)

    Aurélie Collaudin

    2015-06-01

    Full Text Available We present an extensive study of angle-dependent transverse magnetoresistance in bismuth, with a magnetic field perpendicular to the applied electric current and rotating in three distinct crystallographic planes. The observed angular oscillations are confronted with the expectations of semiclassic transport theory for a multivalley system with anisotropic mobility and the agreement allows us to quantify the components of the mobility tensor for both electrons and holes. A quadratic temperature dependence is resolved. As Hartman argued long ago, this indicates that inelastic resistivity in bismuth is dominated by carrier-carrier scattering. At low temperature and high magnetic field, the threefold symmetry of the lattice is suddenly lost. Specifically, a 2π/3 rotation of magnetic field around the trigonal axis modifies the amplitude of the magnetoresistance below a field-dependent temperature. By following the evolution of this anomaly as a function of temperature and magnetic field, we map the boundary in the (field, temperature plane separating two electronic states. In the less symmetric state, confined to low temperature and high magnetic field, the three Dirac valleys cease to be rotationally invariant. We discuss the possible origins of this spontaneous valley polarization, including a valley-nematic scenario.

  19. Bismuth Silver Oxysulfide for Photoconversion Applications: Structural and Optoelectronic Properties

    KAUST Repository

    Baqais, Amal Ali Abdulallh

    2017-09-18

    Single-phase bismuth silver oxysulfide, BiAgOS, was prepared by a hydrothermal method. Its structural, morphological and optoelectronic properties were investigated and compared with bismuth copper oxysulfide (BiCuOS). Rietveld refinement of the powder X-ray diffraction (XRD) measurements revealed that the BiAgOS and BiCuOS crystals have the same structure as ZrSiCuAs: the tetragonal space group P4/nmm. X-ray photoelectron spectroscopy (XPS) analyses confirmed that the BiAgOS has a high purity, in contrast with BiCuOS, which tends to have Cu vacancies. The Ag has a monovalent oxidation state, whereas Cu is present in the oxidation states of +1 and +2 in the BiCuOS system. Combined with experimental measurements, density functional theory calculations employing the range-separated hybrid HSE06 exchange-correlation functional with spin-orbit coupling quantitatively elucidated photophysical properties such as ab-sorption coefficients, effective masses and dielectric constants. BiCuOS and BiAgOS were found to have indirect bandgaps of 1.1 and 1.5 eV, respectively. Both possess high dielectric constants and low electron and hole effective masses. Therefore, these materials are expected to have high exciton dissociation capabilities and excellent carrier diffusion properties. This study reveals that BiAgOS is a promising candidate for photoconversion applications.

  20. Magneto-photoconductivity of three dimensional topological insulator bismuth telluride

    Science.gov (United States)

    Cao, Bingchen; Eginligil, Mustafa; Yu, Ting

    2018-03-01

    Magnetic field dependence of the photocurrent in a 3D topological insulator is studied. Among the 3D topological insulators bismuth telluride has unique hexagonal warping and spin texture which has been studied by photoemission, scanning tunnelling microscopy and transport. Here, we report on low temperature magneto-photoconductivity, up to 7 T, of two metallic bismuth telluride topological insulator samples with 68 and 110 nm thicknesses excited by 2.33 eV photon energy along the magnetic field perpendicular to the sample plane. At 4 K, both samples exhibit negative magneto-photoconductance below 4 T, which is as a result of weak-antilocalization of Dirac fermions similar to the previous observations in electrical transport. However the thinner sample shows positive magneto-photoconductance above 4 T. This can be attributed to the coupling of surface states. On the other hand, the thicker sample shows no positive magneto-photoconductance up to 7 T since there is only one surface state at play. By fitting the magneto-photoconductivity data of the thicker sample to the localization formula, we obtain weak antilocalization behaviour at 4, 10, and 20 K, as expected; however, weak localization behaviour at 30 K, which is a sign of surface states masked by bulk states. Also, from the temperature dependence of phase coherence length bulk carrier-carrier interaction is identified separately from the surface states. Therefore, it is possible to distinguish surface states by magneto-photoconductivity at low temperature, even in metallic samples.

  1. Genotoxic effects of bismuth (III oxide nanoparticles by comet assay

    Directory of Open Access Journals (Sweden)

    Reecep Liman

    2015-06-01

    Full Text Available Bismuth oxide is one of the important transition metal oxides and it has been intensively studied due to their peculiar characteristics (semiconductor band gap, high refractive index, high dielectric permittivity, high oxygen conductivity, resistivity, photoconductivity and photoluminescence etc.. Therefore, it is used such as microelectronics, sensor technology, optical coatings, transparent ceramic glass manufacturing, nanoenergetic gas generator, biosensor for DNA hybridization, potential immobilizing platforms for glucose oxidase and polyphenol oxidase, fuel cells, a additive in paints, an astringent in a variety of medical creams and topical ointments, and for the determination of heavy metal ions in drinking water, mineral water and urine. In addition this, Bismuth (III oxide nanoparticles (BONPs are favorable for the biomolecules adsorption than regular sized particles because of their greater advantages and novel characteristics (much higher specific surface, greater surface free energy, and good electrochemical stability etc.. Genotoxic effects of BONPs were investigated on the root cells of Allium cepa by Comet assay. A. cepa roots were treated with the aqueous dispersions of BONPs at 5 different concentrations (12.5, 25, 50, 75, and 100 ppm for 4 h. A significant increase in DNA damage was also observed at all concentrations of BONPs except 12.5 ppm by Comet assay. The results were also analyzed statistically by using SPSS for Windows; Duncan’s multiple range test was performed. These result indicate that BONPs exhibit genotoxic activity in A. cepa root meristematic cells.

  2. Magnetic anisotropies in ultrathin bismuth iron garnet films

    International Nuclear Information System (INIS)

    Popova, Elena; Franco Galeano, Andres Felipe; Deb, Marwan; Warot-Fonrose, Bénédicte; Kachkachi, Hamid; Gendron, François; Ott, Frédéric

    2013-01-01

    Ultrathin bismuth iron garnet Bi 3 Fe 5 O 12 films were grown epitaxially on (001)-oriented gadolinium gallium garnet substrates. Film thickness varied from two to three dozens of unit cells. Bi 3 Fe 5 O 12 films grow pseudomorphically on substrates up to a thickness of 20 nm, and then a lattice relaxation occurs. Magnetic properties of the films were studied as a function of bismuth iron garnet thickness. The magnetization and cubic anisotropy decrease with decreasing film thickness. The uniaxial magnetocrystalline anisotropy is constant for all film thicknesses. For two unit cell thick films, the easy magnetization axis changes from in-plane to perpendicular to the plane direction. Such a reorientation takes place as a result of the competition of constant uniaxial perpendicular anisotropy with weakening film magnetization. - Highlights: ► Ultrathin Bi 3 Fe 5 O 12 films were grown epitaxially on structure-matching substrates. ► Magnetic properties of Bi 3 Fe 5 O 12 were studied down to the thickness of 2.5 nm. ► Reorientation of easy magnetization axis as a function of film thickness was observed

  3. Magnetic anisotropies in ultrathin bismuth iron garnet films

    Energy Technology Data Exchange (ETDEWEB)

    Popova, Elena, E-mail: popova@physique.uvsq.fr [Groupe d' Etude de la Matière Condensée (GEMaC), CNRS/Université de Versailles-Saint-Quentin, 45 Avenue des Etats-Unis, 78035 Versailles (France); Franco Galeano, Andres Felipe [Laboratoire PROcédés, Matériaux et Energie Solaire (PROMES), CNRS/Université de Perpignan Via Domitia, 52 Avenue Paul Alduy, 66860 Perpignan (France); Deb, Marwan [Groupe d' Etude de la Matière Condensée (GEMaC), CNRS/Université de Versailles-Saint-Quentin, 45 Avenue des Etats-Unis, 78035 Versailles (France); Warot-Fonrose, Bénédicte [Centre d' Elaboration de Matériaux et d' Etudes Structurales (CEMES), CNRS, 29 rue Jeanne Marvig, 31055 Toulouse (France); Transpyrenean Associated Laboratory for Electron Microscopy (TALEM), CEMES-INA, CNRS–Universidad de Zaragoza (Spain); Kachkachi, Hamid [Laboratoire PROcédés, Matériaux et Energie Solaire (PROMES), CNRS/Université de Perpignan Via Domitia, 52 Avenue Paul Alduy, 66860 Perpignan (France); Gendron, François [Institut des NanoSciences de Paris (INSP), CNRS/Université Pierre et Marie Curie-Paris 6, 4 place Jussieu, Boîte courrier 840, 75252 Paris Cedex 05 (France); Ott, Frédéric [Laboratoire Léon Brillouin (LLB), CNRS/CEA, Bâtiment 563, CEA Saclay, 91191 Gif sur Yvette Cedex (France); and others

    2013-06-15

    Ultrathin bismuth iron garnet Bi{sub 3}Fe{sub 5}O{sub 12} films were grown epitaxially on (001)-oriented gadolinium gallium garnet substrates. Film thickness varied from two to three dozens of unit cells. Bi{sub 3}Fe{sub 5}O{sub 12} films grow pseudomorphically on substrates up to a thickness of 20 nm, and then a lattice relaxation occurs. Magnetic properties of the films were studied as a function of bismuth iron garnet thickness. The magnetization and cubic anisotropy decrease with decreasing film thickness. The uniaxial magnetocrystalline anisotropy is constant for all film thicknesses. For two unit cell thick films, the easy magnetization axis changes from in-plane to perpendicular to the plane direction. Such a reorientation takes place as a result of the competition of constant uniaxial perpendicular anisotropy with weakening film magnetization. - Highlights: ► Ultrathin Bi{sub 3}Fe{sub 5}O{sub 12} films were grown epitaxially on structure-matching substrates. ► Magnetic properties of Bi{sub 3}Fe{sub 5}O{sub 12} were studied down to the thickness of 2.5 nm. ► Reorientation of easy magnetization axis as a function of film thickness was observed.

  4. Superconductivity in Bismuth. A New Look at an Old Problem.

    Science.gov (United States)

    Mata-Pinzón, Zaahel; Valladares, Ariel A; Valladares, Renela M; Valladares, Alexander

    2016-01-01

    To investigate the relationship between atomic topology, vibrational and electronic properties and superconductivity of bismuth, a 216-atom amorphous structure (a-Bi216) was computer-generated using our undermelt-quench approach. Its pair distribution function compares well with experiment. The calculated electronic and vibrational densities of states (eDOS and vDOS, respectively) show that the amorphous eDOS is about 4 times the crystalline at the Fermi energy, whereas for the vDOS the energy range of the amorphous is roughly the same as the crystalline but the shapes are quite different. A simple BCS estimate of the possible crystalline superconducting transition temperature gives an upper limit of 1.3 mK. The e-ph coupling is more preponderant in a-Bi than in crystalline bismuth (x-Bi) as indicated by the λ obtained via McMillan's formula, λc = 0.24 and experiment λa = 2.46. Therefore with respect to x-Bi, superconductivity in a-Bi is enhanced by the higher values of λ and of eDOS at the Fermi energy.

  5. System design study of small lead-bismuth cooled reactor

    International Nuclear Information System (INIS)

    Chikazawa, Yoshitaka; Hori, Toru; Konomura, Mamoru

    2003-07-01

    In phase II of the feasibility study of JNC, we will make a concept of a dispersion power source reactor with various requirements, such as economical competitiveness and safety. In the study of a small lead-bismuth cooled reactor, a concept whose features are long life core, inherent safety, natural convection of cooling system and steam generators in the reactor vessel has been designed since 2000. The investigations which have been done in 2002 are shown as follows; Safety analysis of UTOP considering uncertainty of reactivity. Possibility of reduction of number of control rods. Estimation of construction cost. Transient analyses of UTOP have been done in considering uncertainty of reactivity in order to show the inherent safety in the probabilistic method. And the inherent safety in UTOP is realized under the condition of considering uncertainty. Transient analyses of UTOP with various numbers of control rods have been done and it is suggested that there is possibility of reduction of the number of control rods considering accident managements. The method of cost estimation is a little modified. The cost of reactor vessel is estimated from that of medium sized lead-bismuth cooled reactor and the estimation of a purity control system is by coolant volume flow rate. The construction cost is estimated 850,000yen/kWe. (author)

  6. Electrodeposition of bismuth alloys by the controlled potential method

    International Nuclear Information System (INIS)

    Lopez Alvarez, F.A.

    1993-01-01

    We worked with the electrodeposition of three bismuth alloys, the composition of the first electrolyte was: 0.3 g/l. Bi; 20 g/l. Ni; and the conditions were pH = 5.2 - 5.6; T = 25 Centigrade degrees; current density 0.3 A / dm 2 - 6.6 A / dm 2 . Following alloy was between Bi - Pb, composition of the electrolyte was 3.18 g/l. Bi (metallic); 31.81 g/l. Pb (Pb(NO 3 ) 2 ) pH : 1; T = 20 Centigrade degrees; current density 10.20 A/dm 2 . The third electrolyte was Bi-Cu, its composition was: 20.89 g/l. Bi; (metallic) 63.54 g/l Cu (Cu(NO 3 ) 2 ) pH : 1.5 - 1.8; T = 25-30 Centigrade degrees; current density 1-2 A/dm 2 . The best results were obtained with the third electrolyte. The purpose of this work was to experiment with different parameters like temperature, pH and the electrolyte concentration to obtain a bismuth alloy. (Author)

  7. Polonium-210 and lead-210 in the terrestrial environment: a historical review

    Energy Technology Data Exchange (ETDEWEB)

    Persson, Bertil R.R., E-mail: bertil_r.persson@med.lu.s [Dept. of Medical Radiation Physics, Lund University, Barngatan 2, SE-221 85 Lund (Sweden); Holm, Elis [Norwegian Radiation Protection Authority, Osteras (Norway)

    2011-05-15

    The radionuclides {sup 210}Po and {sup 210}Pb widely present in the terrestrial environment are the final long-lived radionuclides in the decay of {sup 238}U in the earth's crust. Their presence in the atmosphere is due to the decay of {sup 222}Rn diffusing from the ground. The range of activity concentrations in ground level air for {sup 210}Po is 0.03-0.3 Bq m{sup -3} and for {sup 210}Pb 0.2-1.5 Bq m{sup -3}. In drinking water from private wells the activity concentration of {sup 210}Po is in the order of 7-48 mBq l{sup -1} and for {sup 210}Pb around 11-40 mBq l{sup -1}. From water works, however, the activity concentration for both {sup 210}Po and {sup 210}Pb is only in the order of 3 mBq l{sup -1}. Mosses, lichens and peat have a high efficiency in capturing {sup 210}Po and {sup 210}Pb from atmospheric fallout and exhibit an inventory of both {sup 210}Po and {sup 210}Pb in the order of 0.5-5 kBq m{sup -2} in mosses and in lichens around 0.6 kBq m{sup -2}. The activity concentrations in lichens lies around 250 Bq kg{sup -1}, dry mass. Reindeer and caribou graze lichen which results in an activity concentration of {sup 210}Po and {sup 210}Pb of about 1-15 Bq kg{sup -1} in meat from these animals. The food chain lichen-reindeer or caribou, and Man constitutes a unique model for studying the uptake and retention of {sup 210}Po and {sup 210}Pb in humans. The effective annual dose due to {sup 210}Po and {sup 210}Pb in people with high consumption of reindeer/caribou meat is estimated to be around 260 and 132 {mu}Sv a{sup -1} respectively. In soils, {sup 210}Po is adsorbed to clay and organic colloids and the activity concentration varies with soil type and also correlates with the amount of atmospheric precipitation. The average activity concentration levels of {sup 210}Po in various soils are in the range of 20-240 Bq kg{sup -1}. Plants become contaminated with radioactive nuclides both by absorption from the soil (supported Po) and by deposition of radioactive

  8. Measurements and FLUKA simulations of bismuth and aluminium activation at the CERN Shielding Benchmark Facility (CSBF)

    Science.gov (United States)

    Iliopoulou, E.; Bamidis, P.; Brugger, M.; Froeschl, R.; Infantino, A.; Kajimoto, T.; Nakao, N.; Roesler, S.; Sanami, T.; Siountas, A.

    2018-03-01

    The CERN High Energy AcceleRator Mixed field facility (CHARM) is located in the CERN Proton Synchrotron (PS) East Experimental Area. The facility receives a pulsed proton beam from the CERN PS with a beam momentum of 24 GeV/c with 5 ṡ1011 protons per pulse with a pulse length of 350 ms and with a maximum average beam intensity of 6.7 ṡ1010 p/s that then impacts on the CHARM target. The shielding of the CHARM facility also includes the CERN Shielding Benchmark Facility (CSBF) situated laterally above the target. This facility consists of 80 cm of cast iron and 360 cm of concrete with barite concrete in some places. Activation samples of bismuth and aluminium were placed in the CSBF and in the CHARM access corridor in July 2015. Monte Carlo simulations with the FLUKA code have been performed to estimate the specific production yields for these samples. The results estimated by FLUKA Monte Carlo simulations are compared to activation measurements of these samples. The comparison between FLUKA simulations and the measured values from γ-spectrometry gives an agreement better than a factor of 2.

  9. Supported Lead in Pb-210 Chronology

    Energy Technology Data Exchange (ETDEWEB)

    Pittauerova, D.; Hettwig, B.; Fischer, H. W. [Institute of Environmental Physics, University of Bremen, Bremen (Germany)

    2013-07-15

    A widely applied method of supported lead estimation in sediments using gamma spectrometric {sup 226}Ra determination via {sup 222}Rn short lived daughter products relies on radioactive equilibrium between {sup 226}Ra and {sup 222}Rn being established after sealing the samples. Advantages and disadvantages of methods of {sup 226}Ra estimation in sediments, using either {sup 222}Rn daughter products or direct estimation by 186.2 keV gamma emissions are discussed. An equilibrium experiment was performed using test samples and in one case radioactive equilibrium was not reached. On a theoretical sediment profile it was shown how systematic errors in supported {sup 210}Pb estimation can lead to incorrect interpretations of {sup 210}Pb{sub xs} profiles and therefore affect {sup 210}Pb derived chronologies. (author)

  10. Helicobacter pylori second-line rescue therapy with levofloxacin- and bismuth-containing quadruple therapy, after failure of standard triple or non-bismuth quadruple treatments.

    Science.gov (United States)

    Gisbert, J P; Romano, M; Gravina, A G; Solís-Muñoz, P; Bermejo, F; Molina-Infante, J; Castro-Fernández, M; Ortuño, J; Lucendo, A J; Herranz, M; Modolell, I; Del Castillo, F; Gómez, J; Barrio, J; Velayos, B; Gómez, B; Domínguez, J L; Miranda, A; Martorano, M; Algaba, A; Pabón, M; Angueira, T; Fernández-Salazar, L; Federico, A; Marín, A C; McNicholl, A G

    2015-04-01

    The most commonly used second-line Helicobacter pylori eradication regimens are bismuth-containing quadruple therapy and levofloxacin-containing triple therapy, both offering suboptimal results. Combining bismuth and levofloxacin may enhance the efficacy of rescue eradication regimens. To evaluate the efficacy and tolerability of a second-line quadruple regimen containing levofloxacin and bismuth in patients whose previous H. pylori eradication treatment failed. This was a prospective multicenter study including patients in whom a standard triple therapy (PPI-clarithromycin-amoxicillin) or a non-bismuth quadruple therapy (PPI-clarithromycin-amoxicillin-metronidazole, either sequential or concomitant) had failed. Esomeprazole (40 mg b.d.), amoxicillin (1 g b.d.), levofloxacin (500 mg o.d.) and bismuth (240 mg b.d.) was prescribed for 14 days. Eradication was confirmed by (13) C-urea breath test. Compliance was determined through questioning and recovery of empty medication envelopes. Incidence of adverse effects was evaluated by questionnaires. 200 patients were included consecutively (mean age 47 years, 67% women, 13% ulcer). Previous failed therapy included: standard clarithromycin triple therapy (131 patients), sequential (32) and concomitant (37). A total of 96% took all medications correctly. Per-protocol and intention-to-treat eradication rates were 91.1% (95%CI = 87-95%) and 90% (95%CI = 86-94%). Cure rates were similar regardless of previous (failed) treatment or country of origin. Adverse effects were reported in 46% of patients, most commonly nausea (17%) and diarrhoea (16%); 3% were intense but none was serious. Fourteen-day bismuth- and levofloxacin-containing quadruple therapy is an effective (≥90% cure rate), simple and safe second-line strategy in patients whose previous standard triple or non-bismuth quadruple (sequential or concomitant) therapies have failed. © 2015 John Wiley & Sons Ltd.

  11. Complexometric consequent titration of bismuth-titanium mixtures in the μg-region

    International Nuclear Information System (INIS)

    Schaefer, H.

    1975-01-01

    A quantitative method is described for the determination of microquantities of bismuth and titanium. Both metals are determined complexometrically with EDTA and potentiometric equivalence point indication using a Cu-ion sensitive electrode in a consequent titration. The analysis is conducted as back-titration with standard Cu-solution. The relative error of the determination is 0.8% for bismuth (50-100 μg) and for titanium (10-30 μg) at 1.0%. Under the chosen conditions, it is possible to determine as little as 15 μg bismuth and 5 μg titanium by means of this procedure. (author)

  12. Specificities of reactor coolant pumps units with lead and lead-bismuth coolant

    International Nuclear Information System (INIS)

    Beznosov, A.V.; Anotonenkov, M.A.; Bokov, P.A.; Baranova, V.S.; Kustov, M.S.

    2009-01-01

    The analysis results of impact of lead and lead-bismuth coolants specific properties on the coolants flow features in flow channels of the main and auxiliary circulating pumps are presented. Impossibility of cavitation initiation in flow channels of vane pumps pumping lead and lead-bismuth coolants was demonstrated. The experimental research results of discontinuity of heavy liquid metal coolant column were presented and conditions of gas cavitation initiation in coolant flow were discussed. Invalidity of traditional calculation methods of water and sodium coolants circulation pumps calculations for lead and lead-bismuth coolants circulation pumps was substantiated [ru

  13. Topological Insulator State in Thin Bismuth Films Subjected to Plane Tensile Strain

    Science.gov (United States)

    Demidov, E. V.; Grabov, V. M.; Komarov, V. A.; Kablukova, N. S.; Krushel'nitskii, A. N.

    2018-03-01

    The results of experimental examination of galvanomagnetic properties of thin bismuth films subjected to plane tensile strain resulting from the difference in thermal expansion coefficients of the substrate material and bismuth are presented. The resistivity, the magnetoresistance, and the Hall coefficient were studied at temperatures ranging from 5 to 300 K in magnetic fields as strong as 0.65 T. Carrier densities were calculated. A considerable increase in carrier density in films thinner than 30 nm was observed. This suggests that surface states are more prominent in thin bismuth films on mica substrates, while the films themselves may exhibit the properties of a topological insulator.

  14. 210Po- and 210Pb- determination in Hungarian tobacco leaves and dose assessment

    International Nuclear Information System (INIS)

    Kovacs, T.; Bodrogi, E.; Somlai, J.; Baranyi, A.; Dombovari, P.

    2003-01-01

    Because the tobacco of the cigarettes sold in Hungary are domestically grown; the aim of our investigations was to determine the concentrations of 210 Po and 210 Pb in the tobacco plants coming from the different areas of Hungary. Additionally, soil samples and phosphor fertilisers as the potential sources of these radionuclides were also investigated. Special attention was given to the tobacco grown at a tailing pond of a former uranium mine under remediation and the plants grown nearby. One of the biggest tobacco plants is situated there. The 210 Po and 210 Pb concentrations of the investigated tobaccos and cigarettes do not differ considerably, so during the cigarette making process the concentration of these radionuclides does not change to a great extent. The 210 Po concentrations of the phosphate fertilizers available in Hungary were not found extremely high in either case. The ( 210 Po 72-1498 mBq/g, 210 Pb 313-985 mBq/g) concentrations of the tobacco grown at the experiment plant situated at a former uranium mine (waste hip) were high, as expected. This territory is not available for agricultural purposes. Our results also indicate that it is reasonable. The samples from the totally covered (re-mediated) tailing pond are under investigation. (authors)

  15. 210Pb and 210Po as tracers of particle transport mechanisms on continental margins

    International Nuclear Information System (INIS)

    Radakovitch, O.; Heussner, S.; Biscaye, P.; Abassi, A.

    1997-01-01

    The natural radionuclides 210 Po and 210 Pb, members of the 238 U decay chain, are particularly helpful to the understanding of particle transport processes in the ocean. These isotopes were analysed on sediment trap particles collected during 3 one-year experiments on continental margins. In the Bay of Biscay (Northeastern Atlantic) and in the Gulf of Lion (Northwestern Mediterranean Sea) both as part of the French ECOMARGE programme, and in the Middle Atlantic Bight (Northwestern Atlantic) as part of the SEEP programme. They yielded great insights into scenarios of particle transfer at each site, mainly based on the spatial and temporal distribution of 210 Pb particulate concentrations and fluxes. (author)

  16. Transfer of 7Be, 210Pb and 210Po in a forest canopy of Japanese cedar

    International Nuclear Information System (INIS)

    Osaki, S.; Tagawa, Y.; Sugihara, S.; Maeda, Y.; Inokura, Y.

    2003-01-01

    The concentrations of 7 Be, 210 Pb and 210 Po of ca. 60 parts of a whole tree of Japanese cedar and of underlying litter and soil samples were determined for studying their transfer in a forest canopy. The results suggest that the mean residence times of 7 Be and 210 Pb in the forest canopy were ca. 20 and 900 days, respectively, and the dry deposition rate of 7 Be on the forest canopy was about a half of the total deposition rate. (author)

  17. Chemical structure of bismuth compounds determines their gastric ulcer healing efficacy and anti-Helicobacter pylori activity.

    Science.gov (United States)

    Sandha, G S; LeBlanc, R; Van Zanten, S J; Sitland, T D; Agocs, L; Burford, N; Best, L; Mahoney, D; Hoffman, P; Leddin, D J

    1998-12-01

    The recognition of the role of Helicobacter pylori in the pathogenesis of peptic ulcer disease has led to renewed interest in bismuth pharmacology since bismuth compounds have both anti-Helicobacter pylori and ulcer healing properties. The precise chemical structure of current bismuth compounds is not known. This has hindered the development of new and potentially more efficacious formulations. We have created two new compounds, 2-chloro-1,3-dithia-2-bismolane (CDTB) and 1,2-[bis(1,3-dithia-2-bismolane)thio]ethane (BTBT), with known structure. In a rat model of gastric ulceration, BTBT was comparable to, and CDTB was significantly less effective than colloidal bismuth subcitrate in healing cryoprobe-induced ulcers. However, both BTBT and CDTB inhibited H. pylori growth in vitro at concentrations <1/10 that of colloidal bismuth subcitrate. The effects on ulcer healing are not mediated by suppression of acid secretion, pepsin inhibition, or prostaglandin production. Since all treated animals received the same amount of elemental bismuth, it appears that the efficacy of bismuth compounds varies with compound structure and is not simply dependent on the delivery of bismuth ion. Because the structure of the novel compounds is known, our understanding of the relationship of bismuth compound structure and to biologic activity will increase. In the future it may be possible to design other novel bismuth compounds with more potent anti-H. pylori and ulcer healing effects.

  18. Theoretical Investigation of Bismuth-Based Semiconductors for Photocatalytic Applications

    KAUST Repository

    Laradhi, Shaikhah

    2017-11-01

    Converting solar energy to clean fuel has gained remarkable attention as an emerged renewable energy resource but optimum efficiency in photocatalytic applications has not yet been reached. One of the dominant factors is designing efficient photocatalytic semiconductors. The research reveals a theoretical investigation of optoelectronic properties of bismuth-based metal oxide and oxysulfide semiconductors using highly accurate first-principles quantum method based on density functional theory along with the range-separated hybrid HSE06 exchange-correlation functional. First, bismuth titanate compounds including Bi12TiO20, Bi4Ti3O12, and Bi2Ti2O7 were studied in a combined experimental and theoretical approach to prove its photocatalytic activity under UV light. They have unique bismuth layered structure, tunable electronic properties, high dielectric constant and low electron and effective masses in one crystallographic direction allowing for good charge separation and carrier diffusion properties. The accuracy of the investigation was determined by the good agreement between experimental and theoretical values. Next, BiVO4 with the highest efficiency for oxygen evolution was investigated. A discrepancy between the experimental and theoretical bandgap was reported and inspired a systematic study of all intrinsic defects of the material and the corresponding effect on the optical and transport properties. A candidate defective structure was proposed for an efficient photocatalytic performance. To overcome the carrier transport limitation, a mild hydrogen treatment was also introduced. Carrier lifetime was enhanced due to a significant reduction of trap-assisted recombination, either via passivation of deep trap states or reduction of trap state density. Finally, an accurate theoretical approach to design a new family of semiconductors with enhanced optoelectronic properties for water splitting was proposed. We simulated the solid solutions Bi1−xRExCuOS (RE = Y, La

  19. 7 CFR 1160.210 - Expenses.

    Science.gov (United States)

    2010-01-01

    ... and Orders; Milk), DEPARTMENT OF AGRICULTURE FLUID MILK PROMOTION PROGRAM Fluid Milk Promotion Order National Fluid Milk Processor Promotion Board § 1160.210 Expenses. (a) The Board is authorized to incur... funds to the entity authorized by the laws of the State of California to conduct an advertising program...

  20. 7 CFR 210.29 - Management evaluations.

    Science.gov (United States)

    2010-01-01

    ... Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS NATIONAL SCHOOL LUNCH PROGRAM Additional Provisions § 210.29 Management... State agency's monitoring responsibilities; initiation and completion of corrective action; recovery of...

  1. 7 CFR 210.18 - Administrative reviews.

    Science.gov (United States)

    2010-01-01

    ... this section. (d) Scheduling school food authorities. The State agency shall use its own criteria to... claims review process required under § 210.8(b)(2) of this part in the selection of school food... is encouraged to review all schools meeting the school selection criteria specified in paragraph (e...

  2. 48 CFR 210.001 - Policy.

    Science.gov (United States)

    2010-10-01

    ... DEFENSE ACQUISITION PLANNING MARKET RESEARCH 210.001 Policy. (a) In addition to the requirements of FAR 10.001(a), agencies shall— (i) Conduct market research appropriate to the circumstances before— (A... 109-163); and (ii) Use the results of market research to determine— (A) Whether consolidation of...

  3. Aspects on the analysis of 210Po

    DEFF Research Database (Denmark)

    Henricsson, F.; Ranebo, Y.; Holm, E.

    2011-01-01

    -ashing by the use of a double-tracer technique. We have found that the losses were about 30% when open glass beakers were used and about 17% when the samples were digested in microwave oven. When long-necked bottles (Kjeldahl flasks) were used, a loss of about 20% was registered. It has also been observed that 210...

  4. Determination of 210 Po in cigarettes

    International Nuclear Information System (INIS)

    Peres, Ana Claudia; Hiromoto, Goro

    1999-01-01

    A radiochemical procedure for the determination of 110 Po in cigarettes is presented. The method is based on solvent extraction, followed by spontaneous deposition on copper disks and counting by alpha spectrometry. Some commercial cigarette brands available in the national market were analysed, obtaining 210 Po concentrations ranging from 15 to 26 mBq per gram of dry tobacco. (author)

  5. 19 CFR 210.42 - Initial determinations.

    Science.gov (United States)

    2010-04-01

    ... Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Determinations and Actions Taken § 210.42 Initial determinations. (a... Justice, the Federal Trade Commission, the U.S. Customs Service, and such other departments and agencies...

  6. 48 CFR 12.210 - Contract financing.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Contract financing. 12.210... financing. Customary market practice for some commercial items may include buyer contract financing. The contracting officer may offer Government financing in accordance with the policies and procedures in part 32. ...

  7. 7 CFR 210.21 - Procurement.

    Science.gov (United States)

    2010-01-01

    ... Responsibilities § 210.21 Procurement. (a) General. State agencies and school food authorities shall comply with... violation of law are to be referred to the local, State, or Federal authority that has proper jurisdiction... title are followed. A school food authority may use its own procurement procedures which reflect...

  8. 210Po and 210Pb variations in fish species from the Aegean Sea and the contribution of 210Po to the radiation dose

    International Nuclear Information System (INIS)

    Mat Çatal, Ebru; Uğur, Aysun; Özden, Banu; Filizok, Işık

    2012-01-01

    In recent years, there has been increasing interest in the significance of natural radionuclides, particularly 210 Po, in the marine environment. 210 Po, a naturally occurring alpha emitter, accumulates in marine organisms and reflects differences in their diets. In the literature, there is no data for 210 Po and 210 Pb activity concentrations for fish species on the Turkish coast of Aegean Sea. Therefore, in this study, multiple fish species were collected from six stations seasonally on the Turkish coast of Aegean Sea and were analyzed for their 210 Po and 210 Pb content. The 210 Po and 210 Pb concentrations in the fish samples were found to vary from undetectable levels to 499 ± 44 Bq kg −1 dry weight (dw) and from 1.0 ± 0.3 Bq kg −1 to 35 ± 4.0 Bq kg −1 (dw), respectively. There were no significant differences in the activity concentrations of 210 Po and 210 Pb in fish samples between seasons (ANOVA, P > 0.05). The highest dose contribution of 210 Po to humans was calculated to be 10,530 μSv year −1 .

  9. Study of distribution of 210Po and 210Pb in the environmental matrices of Chikmagalur, Karnataka, India

    International Nuclear Information System (INIS)

    Jayasheelan, A.; Sannappa, J.; Umeshareddy, K.; Ningappa, C.; Manjunatha, S.

    2013-01-01

    Polonium-210 and lead-210 are amongst the more radiotoxic nuclides and their concentration in soil and drinking water is very important from a radiological point of view. 210 Po is produced from the decay of 222 Rn gas in the atmosphere from which it is deposited on the earth's surface. 210 Po and 210 Pb in natural environment provide considerable radiation exposure to humans. In the present study, the concentrations of 210 Po and 210 Pb in the environment of Tumkur were studied. Soil and water samples were collected from ten Taluks of Tumkur and 210 Po and 210 Pb were determined by wet ashing method. Samples containing polonium was digested using conc. nitric acid and later converted into chloride medium with HCL. Polonium is deposited on the surface of the silver planchet and the activity on both sides were counted in a low background alpha counting system. The sample solution after estimation of 210 Po was preserved for 6-8 months for sufficient growth of 210 Po from 210 Pb. Then the 210 Po was re-estimated to determine the 210 Pb concentration by knowing its growth factor. The concentrations of 210 Po and 210 Pb in soils of different Taluks varied from 13.6 BqKg -1 and 26.8 to 113.4 BqKg -1 respectively. The concentrations of 210 Po and 210 Pb in water was low compared to soil, they varied 0.12 Bql -1 to 0.54 Bql -1 and 0.42 Bql -1 to 1.12 Bql -1 . (author)

  10. Polonium-210 and lead-210 in edible molluscs from near the Cape of Good Hope: sources of variability in polonium-210 concentrations

    International Nuclear Information System (INIS)

    Heyraud, M.; Cherry, R.D.; Oschadleus, H.-D.; Cherry, M.I.; Sealy, J.C.

    1994-01-01

    Measurements of the natural radionuclides 210 Po and 210 Pb in mussels, squid and oysters from near the Cape of Good Hope are reported and compared with previously published 210 Po and 210 Pb data from Northern Hemisphere organisms in the same taxa. Emphasis is laid on discussing the causes of variability in the concentrations of 210 Po in marine organisms. No systematic evidence is found for a 'latitude' effect, but allometric effects, intertaxon differences, change of diet with animal size and regional effects are all significant for 210 Po. The consequences for human radiation dose calculations of variability of 210 Po levels in seafoods are discussed briefly; particular reference is made to the case of a Stone Age mussel-eating community in South Africa. (author)

  11. Shielding property of bismuth glass based on MCNP 5 and WINXCOM simulated calculation

    International Nuclear Information System (INIS)

    Zhang Zhicheng; Zhang Jinzhao; Liu Ze; Lu Chunhai; Chen Min

    2013-01-01

    Background: Currently, lead glass is widely used as observation window, while lead is toxic heavy metal. Purpose: Non-toxic materials and their shielding effects are researched in order to find a new material to replace lead containing material. Methods: The mass attenuation coefficients of bismuth silicate glass were investigated with gamma-ray's energy at 0.662 MeV, 1.17 MeV and 1.33 MeV, respectively, by MCNP 5 (Monte Carlo) and WINXCOM program, and compared with those of the lead glass. Results: With attenuation factor K, shielding and mechanical properties taken into consideration bismuth glass containing 50% bismuth oxide might be selected as the right material. Dose rate distributions of water phantom were calculated with 2-cm and 10-cm thick glass, respectively, irradiated by 137 Cs and 60 Co in turn. Conclusion: Results show that the bismuth glass may replace lead glass for radiation shielding with appropriate energy. (authors)

  12. Corrosion by liquid lead and lead-bismuth: experimental results review and analysis

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jinsuo [Los Alamos National Laboratory

    2008-01-01

    Liquid metal technologies for liquid lead and lead-bismuth alloy are under wide investigation and development for advanced nuclear energy systems and waste transmutation systems. Material corrosion is one of the main issues studied a lot recently in the development of the liquid metal technology. This study reviews corrosion by liquid lead and lead bismuth, including the corrosion mechanisms, corrosion inhibitor and the formation of the protective oxide layer. The available experimental data are analyzed by using a corrosion model in which the oxidation and scale removal are coupled. Based on the model, long-term behaviors of steels in liquid lead and lead-bismuth are predictable. This report provides information for the selection of structural materials for typical nuclear reactor coolant systems when selecting liquid lead or lead bismuth as heat transfer media.

  13. On the origin of near-IR luminescence in SiO{sub 2} glass with bismuth as the single dopant. Formation of the photoluminescent univalent bismuth silanolate by SiO{sub 2} surface modification

    Energy Technology Data Exchange (ETDEWEB)

    Romanov, A.N., E-mail: alexey.romanov@list.ru; Haula, E.V.; Shashkin, D.P.; Vtyurina, D.N.; Korchak, V.N.

    2017-03-15

    Near infrared photoluminescent bismuth(I) silanolate centers ((≡Si-O){sub 3}Si–O-Bi) were prepared on the surface of SiO{sub 2} xerogel, by the treatment in the vapors of bismuth(I) chloride. The optical properties of these groups are almost identical to that of photoluminescent centers in the bulk SiO{sub 2} glasses with bismuth as the single dopant. - Highlights: • univalent bismuth silanolate can be prepared on SiO{sub 2} surface by treatment in BiCl vapors. • univalent bismuth silanolate is responsible for NIR photoluminescence in Bi-doped SiO{sub 2} glass. • univalent bismuth silanolate is the active center in laser, operating on Bi-doped SiO{sub 2} fiber.

  14. Study of irradiation defects in bismuth by electric transport measurements

    International Nuclear Information System (INIS)

    Le Goff, M.

    1984-01-01

    Pure monocrystalline bismuth is irradiated near 4K by electrons of different energies. Irradiation effects are measured by galvanomagnetic properties at low temperature. Frenkel pairs created during irradiation have a strong effect on carrier mobilities. The data are quantitatively analyzed assuming a rigid band model. After irradiation with 1 MeV electrons, each Frankel pair created corresponds to a total charge of 0.14 electrons. This result obtained by magnetoresistance and Hall effect is confirmed by Shubnikov-de Haas experiments. There is a linear variation between the excess carrier density (p-n) and the Frenkel pair concentration. The more important step of annealing is observed around 40-50 K. This step is attributed to interstitial migration. Resistivity presents a minimum at low temperature after irradiation with electrons of energy over 1.3 MeV. This is explained by virtual bound levels near the Fermi level. The Kondo effect bound to magnetic defects is discussed [fr

  15. Ni-rich precipitates in a lead bismuth eutectic loop

    International Nuclear Information System (INIS)

    Kikuchi, K.; Saito, S.; Hamaguchi, D.; Tezuka, M.

    2010-01-01

    Solidified LBE was sampled from the specimens, electro-magnetic pump, filter, drain valve and oxygen sensor at the JAEA Lead Bismuth Loop-1 (JLBL-1) where the structural material was made of SS316. The concentration of Ni, Fe and Cr in LBE were analyzed by the Inductive Coupled Plasma atomic emission spectrometer. It was concluded that the solution of Ni into LBE was not saturated although the concentration of Fe and Cr almost achieved to the values in the literature. A needle-type structure appeared on the surface of solidified LBE inside the tube specimens. It was found to be Ni-rich precipitates by X-ray analyses (Field Emission Scanning Electron Microscope, FE-SEM). LBE samples collected from a circulating loop after discharging did not show the amount of impurities equivalent to the LBE bulk property.

  16. Ni-rich precipitates in a lead bismuth eutectic loop

    Energy Technology Data Exchange (ETDEWEB)

    Kikuchi, K., E-mail: kikuchik@mx.ibaraki.ac.j [Ibaraki University, IQBRC, Tokai, Ibaraki 319-1106 (Japan); Saito, S.; Hamaguchi, D.; Tezuka, M. [J-PARC Center, JAEA, Tokai, Ibaraki 319-1195 (Japan)

    2010-03-15

    Solidified LBE was sampled from the specimens, electro-magnetic pump, filter, drain valve and oxygen sensor at the JAEA Lead Bismuth Loop-1 (JLBL-1) where the structural material was made of SS316. The concentration of Ni, Fe and Cr in LBE were analyzed by the Inductive Coupled Plasma atomic emission spectrometer. It was concluded that the solution of Ni into LBE was not saturated although the concentration of Fe and Cr almost achieved to the values in the literature. A needle-type structure appeared on the surface of solidified LBE inside the tube specimens. It was found to be Ni-rich precipitates by X-ray analyses (Field Emission Scanning Electron Microscope, FE-SEM). LBE samples collected from a circulating loop after discharging did not show the amount of impurities equivalent to the LBE bulk property.

  17. Ni-rich precipitates in a lead bismuth eutectic loop

    Science.gov (United States)

    Kikuchi, K.; Saito, S.; Hamaguchi, D.; Tezuka, M.

    2010-03-01

    Solidified LBE was sampled from the specimens, electro-magnetic pump, filter, drain valve and oxygen sensor at the JAEA Lead Bismuth Loop-1 (JLBL-1) where the structural material was made of SS316. The concentration of Ni, Fe and Cr in LBE were analyzed by the Inductive Coupled Plasma atomic emission spectrometer. It was concluded that the solution of Ni into LBE was not saturated although the concentration of Fe and Cr almost achieved to the values in the literature. A needle-type structure appeared on the surface of solidified LBE inside the tube specimens. It was found to be Ni-rich precipitates by X-ray analyses (Field Emission Scanning Electron Microscope, FE-SEM). LBE samples collected from a circulating loop after discharging did not show the amount of impurities equivalent to the LBE bulk property.

  18. Bismuth Sodium Titanate Based Materials for Piezoelectric Actuators.

    Science.gov (United States)

    Reichmann, Klaus; Feteira, Antonio; Li, Ming

    2015-12-04

    The ban of lead in many electronic products and the expectation that, sooner or later, this ban will include the currently exempt piezoelectric ceramics based on Lead-Zirconate-Titanate has motivated many research groups to look for lead-free substitutes. After a short overview on different classes of lead-free piezoelectric ceramics with large strain, this review will focus on Bismuth-Sodium-Titanate and its solid solutions. These compounds exhibit extraordinarily high strain, due to a field induced phase transition, which makes them attractive for actuator applications. The structural features of these materials and the origin of the field-induced strain will be revised. Technologies for texturing, which increases the useable strain, will be introduced. Finally, the features that are relevant for the application of these materials in a multilayer design will be summarized.

  19. Lead-Bismuth technology ; corrosion resistance of structural materials

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Ji Young; Park, Won Seok [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-02-01

    Lead-Bismuth (Pb-Bi) eutectic alloy was determined as a coolant material for the HYPER system being studied by KAERI. The Pb-Bi alloy as a coolant, has a number of the favorable thermo-physical and technological properties, while it is comparatively corrosive to the structural materials. It is necessary to solve this problem for providing a long failure-proof operation of the facilities with Pb-Bi coolant. It seems to be possible to maintain corrosion resistance on structural material up to 600 deg C by using of various technologies, but it needs more studies for application to large-scale NPPs. 22 refs., 11 figs., 7 tabs. (Author)

  20. Stimulated Raman scattering of sub-millimeter waves in bismuth

    Science.gov (United States)

    Kumar, Pawan; Tripathi, V. K.

    2007-12-01

    A high-power sub-millimeter wave propagating through bismuth, a semimetal with non-spherical energy surfaces, parametrically excites a space-charge mode and a back-scattered electromagnetic wave. The free carrier density perturbation associated with the space-charge wave couples with the oscillatory velocity due to the pump to derive the scattered wave. The scattered and pump waves exert a pondermotive force on electrons and holes, driving the space-charge wave. The collisional damping of the decay waves determines the threshold for the parametric instability. The threshold intensity for 20 μm wavelength pump turns out to be ˜2×1012 W/cm2. Above the threshold, the growth rate scales increase with ωo, attain a maximum around ωo=6.5ωp, and, after this, falls off.

  1. Radiopacity and histological assessment of Portland cement plus bismuth oxide.

    Science.gov (United States)

    Coutinho-Filho, Tauby; De-Deus, Gustavo; Klein, Leila; Manera, Gisele; Peixoto, Carla; Gurgel-Filho, Eduardo Diogo

    2008-12-01

    The present study evaluated the subcutaneous connective tissue reactions and the radiopacity of MTA, Portland cement (PC), and Portland cement plus bismuth oxide (BO). Forty rats were divided into 5 groups (n = 8 per group): A1: Control (empty capsule); A2: Pro-Root MTA; A3: PC; A4: PC + BO 1:1; and A5: PC + BO 2:1. Polyethylene tubes were filled with the test materials and standardized radiographic images were taken. Histological evaluation was done after 7 and 60 days. Student t test and Fisher's test were used in the statistical analysis (P A4 > A5 > A3. No differences were found for the tissue response in the 2 experimental periods. A positive correlation between BO concentration and radiopacity of PC was determined. The histological evaluation suggests that all studied materials were biocompatible at 7 and 60 days.

  2. High ionic conductivity in confined bismuth oxide-based heterostructures

    Directory of Open Access Journals (Sweden)

    Simone Sanna

    2016-12-01

    Full Text Available Bismuth trioxide in the cubic fluorite phase (δ-Bi2O3 exhibits the highest oxygen ionic conductivity. In this study, we were able to stabilize the pure δ-Bi2O3 at low temperature with no addition of stabilizer but only by engineering the interface, using highly coherent heterostructures made of alternative layers of δ-Bi2O3 and Yttria Stabilized Zirconia (YSZ, deposited by pulsed laser deposition. The resulting [δ-Bi2O3/YSZ] heterostructures are found to be stable over a wide temperature range (500-750 °C and exhibits stable high ionic conductivity over a long time comparable to the value of the pure δ-Bi2O3, which is approximately two orders of magnitude higher than the conductivity of YSZ bulk.

  3. High ionic conductivity in confined bismuth oxide-based heterostructures

    DEFF Research Database (Denmark)

    Sanna, Simone; Esposito, Vincenzo; Christensen, Mogens

    2016-01-01

    Bismuth trioxide in the cubic fluorite phase (δ-Bi2O3) exhibits the highest oxygen ionic conductivity. In this study, we were able to stabilize the pure -Bi2O3 at low temperature with no addition of stabilizer but only by engineering the interface, using highly coherent heterostructures made...... of alternative layers of δ-Bi2O3 and Yttria Stabilized Zirconia (YSZ), deposited by pulsed laser deposition. The resulting [δ-Bi2O3=YSZ] heterostructures are found to be stable over a wide temperature range (500-750 °C) and exhibits stable high ionic conductivity over a long time comparable to the value...... of the pure δ-Bi2O3, which is approximately two orders of magnitude higher than the conductivity of YSZ bulk....

  4. Study of bismuth minerals belonging to the mineralogical collection from the National Museum

    International Nuclear Information System (INIS)

    Baptista, A.; Baptista, N.R.

    1991-09-01

    With the purpose of searching the presence of Tellurium minerals in the Ouro Preto-Mariana country, Minas Gerais State, and considering the existence of a great number of minerals in which this element come across allied with Bismuth, samples of the mineralogical collection of the Museu Nacional, proceeding that region and classified as Bismuth minerals were studied by X-ray fluorescence analysis and diffractometric analysis. In this report the results of this research are presented. (Author)

  5. About thermo-electric properties of bismuth telluride doped by gadolinium

    International Nuclear Information System (INIS)

    Akperov, M.M.; Ismailov, Sh.S.; Shukyurova, A.A.

    2004-01-01

    Results of study of the Gd impurities effect on the bismuth telluride thermo-electric properties are presented. The experiment was carried out within the temperature range T=300-700 K. It is determined, that at temperature increase the energy level is appreciably closing up to bismuth telluride forbidden zone which makes up 0.16-0.24 eV. Such anomalous energy properties of gadolinium in telluride affect on material thermoelectric properties

  6. Bismuth oxide nanorods based immunosensor for mycotoxin detection

    Energy Technology Data Exchange (ETDEWEB)

    Solanki, Pratima R., E-mail: pratimarsolanki@gmail.com [DST Centre for Biomolecular Electronics, CSIR-National Physical Laboratory, K.S. Krishnan Marg, New Delhi (India); Special Centre for Nano Sciences, Jawaharlal Nehru University, New Delhi 110067 (India); Singh, Jay [DST Centre for Biomolecular Electronics, CSIR-National Physical Laboratory, K.S. Krishnan Marg, New Delhi (India); Department of Applied Chemistry and Polymer Technology, Delhi Technological University, Shahbad Daulatpur, Main Bawana Road, Delhi 110042 (India); Rupavali, Bharti [DST Centre for Biomolecular Electronics, CSIR-National Physical Laboratory, K.S. Krishnan Marg, New Delhi (India); Tiwari, Sachchidanand [Special Centre for Nano Sciences, Jawaharlal Nehru University, New Delhi 110067 (India); Malhotra, Bansi D., E-mail: bansi.malhotra@gmail.com [DST Centre for Biomolecular Electronics, CSIR-National Physical Laboratory, K.S. Krishnan Marg, New Delhi (India); Department of Biotechnology, Delhi Technological University, Shahbad Daulatpur, Main Bawana Road, Delhi 110042 (India)

    2017-01-01

    We report results of the studies relating to fabrication of an efficient immunosensor based on bismuth oxide nanorods (nBi{sub 2}O{sub 3}), electrophoretically deposited onto indium-tin-oxide (ITO) coated glass substrate. This immunosensor was fabricated by immobilization of anti-aflatoxin monoclonal antibodies (Ab-AFB1) and bovine serum albumin (BSA) for aflatoxin B1 detection. The structural and morphological studies of n-Bi{sub 2}O{sub 3} have been carried out by XRD, UV–vis spectrophotometer; SEM, AFM and FTIR. It was found that the nBi{sub 2}O{sub 3} provided improved sensing characteristics to the electrode interface in terms of electroactive surface area, diffusion coefficient, charge transfer rate constant and electron transfer kinetics. The results of electrochemical response studies of this BSA/Ab-AFB1/nBi{sub 2}O{sub 3}/ITO immunosensor revealed good linearity in the range of 1–70 ng dL{sup −1} with low detection limit of 8.715 ng/dL, improved sensitivity of 1.132 μA/(ng/dL cm{sup −2}), regression coefficient R{sup 2} of 0.918 and reproducibility of > 11 times. The association constant for the BSA/Ab-AFB1/nBi{sub 2}O{sub 3}/ITO immunosensor was determined as 7.318 ng/dL. - Highlights: • Use of Bismuth oxide nanorods for aflatoxin B1 detection. • It improved the electrochemical properties. • First report on nBi{sub 2}O{sub 3} for mycotoxin detection.

  7. Magnetic properties of the binary Nickel/Bismuth alloy

    Energy Technology Data Exchange (ETDEWEB)

    Keskin, Mustafa; Şarlı, Numan, E-mail: numansarli82@gmail.com

    2017-09-01

    Highlights: • We model and investigate the magnetic properties of the Ni/Bi alloy within the EFT. • Magnetizations of the Ni/Bi alloy are observed as Bi1 > Bi2 > Ni/Bi > Ni at T < Tc. • Magnetization of the Bi1 is dominant and Ni is at least dominant T < Tc. • Total magnetization of the Ni/Bi alloy is close to those of Ni at T < Tc. • Hysteresis curves are overlap at T < 0.1 and they behave separately at T > 0.1. - Abstract: Magnetic properties of the binary Nickel/Bismuth alloy (Ni/Bi) are investigated within the effective field theory. The Ni/Bi alloy has been modeled that the rhombohedral Bi lattice is surrounded by the hexagonal Ni lattice. According to lattice locations, Bi atoms have two different magnetic properties. Bi1 atoms are in the center of the hexagonal Ni atoms (Ni/Bi1 single layer) and Bi2 atoms are between two Ni/Bi1 bilayers. The Ni, Bi1, Bi2 and Ni/Bi undergo a second-order phase transition from the ferromagnetic phase to paramagnetic phase at Tc = 1.14. The magnetizations of the Ni/Bi alloy are observed as Bi1 > Bi2 > Ni/Bi > Ni at T < Tc; hence the magnetization of the Bi1 is dominant and Ni is at least dominant. However, the total magnetization of the Ni/Bi alloy is close to magnetization of the Ni at T < Tc. The corcivities of the Ni, Bi1, Bi2 and Ni/Bi alloy are the same with each others, but the remanence magnetizations are different. Our theoretical results of M(T) and M(H) of the Ni/Bi alloy are in quantitatively good agreement with the some experimental results of binary Nickel/Bismuth systems.

  8. Discharge of 210Po and 210Pb in coastal groundwater to the ocean

    International Nuclear Information System (INIS)

    Kim, Intae; Kim, Tae-hoon; Kim, Guebuem

    2013-01-01

    The activities of 210 Po and 210 Pb were measured for the truly dissolved (<10 kDa) and colloidal (10 kDa - 0.45 ìm) phases in coastal ground water in 2010 and 2011. The sampling sites include the coast of a large tidal flat (Hampyeong Bay) and a volcanic island, Jeju, Korea, where submarine groundwater discharge (SGD) were reported to be higher than typical continental margins. The total dissolved fraction was separated into the colloidal and truly dissolved fractions using a tangential flow filtration (TFF) system (PLCGC Pellicon). The total 210 Po and 210 Pb activities in ground water were 1.0 - 18.2 dpm/100L (9.7±7.6 dpm/100L) an 2.9 - 29.1 dpm/100L (16.8±10.7 dpm/100L) in the Hampyeong Bay and Jeju Island samples, respectively. The total 210 Po and 210 Pb activities in groundwater were similar to or even slightly lower than those in the typical seawater. These lower activities seem to be due to the rapid adsorption of Po and Pb on to particles in the subterranean estuary. The proportions of the truly dissolved and colloidal phases were, respectively, 73±5% and 27±5% for 210 Po, and 60±5% and 40±5% for 210 Pb. This result is consistent with the earlier study that more than half of the some dissolved trace metals in coastal ground water are in the colloidal form. Thus, our result implies that the colloidal forms are important in controlling the behaviour of Po, Pb, and other trace metals in the subterranean estuary and SGD-associated fluxes to the ocean. (author)

  9. Speciation of 210Po and 210Pb in air particulates determined by sequential extraction

    International Nuclear Information System (INIS)

    Al-Masri, M.S.; Al-Karfan, K.; Khalili, H.; Hassan, M.

    2006-01-01

    Speciation of 210 Po and 210 Pb in air particulates of two Syrian phosphate sites with different climate conditions has been studied. The sites are the mines and Tartous port at the Mediterranean Sea. Air filters were collected during September 2000 until February 2002 and extracted chemically using different selective fluids in an attempt to identify the different forms of these two radionuclides. The results have shown that the inorganic and insoluble 21 Po and 21 Pb (attached to silica and soluble in mineral acids) portion was found to be high in both sites and reached a maximum value of 94% and 77% in the mine site and Tartous port site, respectively. In addition, only 24% of 21 Pb in air particulates was found to be associated with organic materials probably produced from the incomplete burning of fuel vehicle and similar activities. Moreover, the 210 Po/ 21- Pb activity ratio in air particulates was higher than that in all samples at both sites and varied between 3.85 in November 2000 at Tartous port site and 20 in April 2001 at the mine area. These activity ratios were also higher than the natural levels. The 210 Po/ 210 Pb activity ratio was also determined in each portion resulting from the selective extraction and found to be higher than that in most samples. The sources of 210 Po excess in these portions are discussed. Soil suspension, which is common in the dry climate dominant in the area, sea water spray and heating of phosphate ores were considered; polonium is more volatile than the lead compounds at even moderate temperature. Furthermore, variations in the chemical forms of 210 Po and 210 Pb during the year were also investigated. However, the results of this study can also be utilized for dose assessment to phosphate industry workers

  10. Uptake and kinetics of 226Ra, 210Pb and 210Po in big sagebrush

    International Nuclear Information System (INIS)

    Simon, S.L.

    1985-01-01

    Root uptake of 226 Ra, 210 Pb and 210 Po by mature sagebrush was studied using a soil injection method for spiking the soil with minimal root disturbance. The main objective was to measure vegetation concentrations and determine concentration ratios (CR's) due to root uptake as a function of time in mature big sagebrush. Concentration ratios obtained in mature vegetation and in steady-state situations may be valuable in assessing the impact of uranium mining and milling. The vegetation was sampled approximately every 3 months for a 2 year period. Significant levels of activity were detected in the vegetation beginning at the first sampling (81 days after soil injection for 226 Ra, 28 days for 210 Pb and 210 Po). There was an exponential decrease in concentration to an apparent steady-state value. Mean values (geometric) of the data pooled over the second year period indicated that the steady-state CR's for 226 Ra, 210 Pb and 210 Po, as determined in mature sagebrush, were 0.04, 0.009, and 0.08, respectively. A three compartment mathematical model was formulated to help understand mechanisms of plant uptake and to predict, if possible, the concentration of 226 Ra, 210 Pb and 210 Po in vegetation as a function of time after soil spiking. A numerical solution was determined by 'calibrating' the general model solution with constants determined from regressions of concentrations in vegetation, soil leaching and leaf leaching data. Validation of the model is currently not possible because of an absence of similar time-dependent uptake studies. 168 refs., 19 figs., 18 tabs

  11. Normal dietary levels of radium-226, radium-228, lead-210, and polonium-210 for man

    International Nuclear Information System (INIS)

    Holtzman, R.B.

    1980-01-01

    A review of the literature and the results of some recent measurements on the levels in man's diet of the naturally occurring radionuclides 226 Ra, 228 Ra, 210 Pb, and 210 Po are presented. Intakes in other countries are similar to those in the United States, but in localized populations the 226 Ra intake can be 8 or more pCi/day. The few data on 228 Ra show that intake of this nuclide is about 80% that of 226 Ra except in monazite areas where intakes of up to 160 pCi 228 Ra/day are reported. Drinking water contributes less than 5% to daily intake except in special areas. For 210 Pb, higher levels have been noted for Germany and the Union of Soviet Socialist Republics than for the United States. Persons in the Arctic who consume reindeer or caribou meat may ingest 210 Pb at the rate of 10 to 40 pCi/day. Normal dietary levels of 210 Po are about 20 to 30% higher than those of 210 Pb, except in the Arctic. The levels of these nuclides in classes of foods are compared to show that the higher levels observed in certain diets are due to the levels in particular foods. Because of the high levels of 210 Pb intake in Japan, total skeletal dose rates in that country are estimated to be more than twice those in the United States. The use of dietary intake for estimating metabolic parameters, such as intestinal absorption of 226 Ra and 210 Pb, is discussed

  12. Variability of excretion rates of 210Pb and 210Po of humans at environmental levels

    International Nuclear Information System (INIS)

    Spencer, H.; Holtzman, R.B.; Ilcewicz, F.H.; Kramer, L.

    1977-01-01

    Variability of the excretion rates of the nuclides 210 Pb and 210 Po at natural levels was studied in a group of samples collected from men maintained under the carefully controlled conditions of a metabolic ward. They consumed only the standard diet of the ward in which they had been resident for at least several months prior to this study. The mean urinary rates were about 0.1 to 0.5 pCi/day for both 210 Pb and 210 Po, while fecal rates ranged from 1 to 2.7 pCi/day for the two nuclides. For urinary 210 Pb the coefficients of variation (ratio of standard deviation to mean) for three subjects ranged from 19 to 45 percent for eight continuous 24-hr samples compared to 11 to 13 percent for subsequently collected multiday samples (4 to 9 days each) for each subject. However, the standard errors of the means for the one day collections were about equal to the standard deviations of the pooled samples. Similar variability was noted for the 210 Po data. Six day fecal collections from these time periods exhibited higher variabilities than did the urine, from about 12 percent to 50 percent for each of the nuclides. Multiday collections for 12 subjects showed mean coefficients of variation of about 16 percent for 210 Pb and 13 percent for the 210 Po for urine and 21 and 25 percent, respectively, in fecal collections. Since dietary intake was maintained fairly constant, excreta collections were carefully controlled, and the analytical precision was about 5 percent, these variabilities appear to be due to biological variations and are characteristic of the individuals studied. Some possible causes of these effects are discussed

  13. Hair and feathers as indicator of internal contamination of 210Po and 210Pb

    Energy Technology Data Exchange (ETDEWEB)

    Holm, E. (ed.); Gwynn, J.; Zaborska, A.; Gaefvert, T. (Norwegian Radiation Protection Authority (Norway)); Roos, P. (Technical Univ. of Denmark, Risoe National Lab. for Sustainable Energy, Roskilde (Denmark)); Henricsson, F. (Lund Univ., Lund (Sweden))

    2010-03-15

    The activities of the NKS-B HAIRPOL project is summarised in this report. The objective was to investigate if hair and feathers were suitable matrices for the estimation of the intake of 210Po. Human hair from people of different sex and age was analysed for 210Po showing concentrations between 0.4 to 11 Bq/kg dry weight. Samples from horses, mane, fur and tail showed concentration from 6 to 17 Bq/kg with no significant difference between the different sample types. Musk ox from Greenland showed much higher concentrations since the animal has to graze a large surface. In fur the concentration was 260 Bq/kg. A considerable fraction of the total 210Po in this animal is contained in the hair. Also different organs were analysed and the highest concentration was found in kidney, 2 700 Bq/kg. The 210Pb concentration in hair was estimated to about 20 Bq/kg. Three different seabirds from Svalbard were analysed. Feathers from all three seabird species show increasing activity concentrations of 210Po and 210Pb from the base to the tip of the feather, but it was difficult to relate feather concentrations to muscle concentrations due to a number of complicating factors. (author)

  14. Hair and feathers as indicator of internal contamination of 210Po and 210Pb

    International Nuclear Information System (INIS)

    Holm, E.; Roos, P.; Henricsson, F.

    2010-03-01

    The activities of the NKS-B HAIRPOL project is summarised in this report. The objective was to investigate if hair and feathers were suitable matrices for the estimation of the intake of 210 Po. Human hair from people of different sex and age was analysed for 210 Po showing concentrations between 0.4 to 11 Bq/kg dry weight. Samples from horses, mane, fur and tail showed concentration from 6 to 17 Bq/kg with no significant difference between the different sample types. Musk ox from Greenland showed much higher concentrations since the animal has to graze a large surface. In fur the concentration was 260 Bq/kg. A considerable fraction of the total 210 Po in this animal is contained in the hair. Also different organs were analysed and the highest concentration was found in kidney, 2 700 Bq/kg. The 210 Pb concentration in hair was estimated to about 20 Bq/kg. Three different seabirds from Svalbard were analysed. Feathers from all three seabird species show increasing activity concentrations of 210 Po and 210 Pb from the base to the tip of the feather, but it was difficult to relate feather concentrations to muscle concentrations due to a number of complicating factors. (author)

  15. Concentration of 210Po and 210Pb in the diet at the Marshall Islands

    International Nuclear Information System (INIS)

    Noshkin, Victor E.; Robison, William L.; Wong, Kai M.

    1994-01-01

    The concentrations of 210 Po and 210 Pb have been determined in many local foods consumed by societies residing on different atolls in the Marshall Islands. The average daily intake of these two naturally occurring radionuclides from local and imported food is estimated to be 2.18 and 0.36 Bq, respectively. Local foods contribute 87% of the 210 Po and 47% of the 210 Pb associated with the diet. The items contributing the majority of the activity to the diet are derived from the marine environment and include parts of fish, invertebrates, seabirds and eggs of seabirds. The committed effective dose from ingestion of 210 Po and 210 Pb is 2 mSv/year (200 mrem/year). This pathway now contributes 83% of the natural background irradiation received by residents in the Marshall Islands. Because the naturally occurring radionuclides are omnipresent in terrestrial and marine foods at all atolls, the annual intake and computed dose can be considered as typical values for individuals with comparable diets and inhabiting other islands in the Pacific

  16. Polonium-210 and lead-210 in marine organisms: allometric relationships and their significance

    International Nuclear Information System (INIS)

    Cherry, R.D.; Heyraud, M.

    1991-01-01

    Allometric relationships which indicate that Po-210 concentrations in marine organisms decrease with increasing organism mass have been reported previously in a few taxa. We report here the results of a study of nearly 400 data covering nine taxa of marine organisms. The data for each taxon are fitted to the allometric equation log Q = log a + b log M, where Q is the Po-210 concentration (mBq/g dry mass) and M is the dry mass per individual (g). The weighted mean of the nine Po-210 slopes is -0.24 ± 0.05, and of the eight Pb-210 slopes is -0.22 ± 0.05. These values are close to the slope of -0.25 frequently found in mass-specific allometric relationships in biology; an association between radionuclide concentration and food ingestion rate is indicated. The intertaxon variations in the intercept log a are large, nearly two orders of magnitude for Po-210, a fact which almost certainly reflects intertaxon differences in diet and/or assimilation. Within taxa, sub-groupings of the Po-210 data are found; these are discussed and an attempt is made to classify them statistically for the data as a whole. (Author)

  17. Concentration of 210Po and 210Pb in the diet at the Marshall Islands.

    Science.gov (United States)

    Noshkin, V E; Robison, W L; Wong, K M

    1994-09-30

    The concentrations of 210Po and 210Pb have been determined in many local foods consumed by societies residing on different atolls in the Marshall Islands. The average daily intake of these two naturally occurring radionuclides from local and imported food is estimated to be 2.18 and 0.36 Bq, respectively. Local foods contribute 87% of the 210Po and 47% of the 210Pb associated with the diet. The items contributing the majority of the activity to the diet are derived from the marine environment and include parts of fish, invertebrates, seabirds and eggs of seabirds. The committed effective dose from ingestion of 210Po and 210Pb is approximately 2 mSv/year (200 mrem/year). This pathway now contributes 83% of the natural background irradiation received by residents in the Marshall Islands. Because the naturally occurring radionuclides are omnipresent in terrestrial and marine foods at all atolls, the annual intake and computed dose can be considered as typical values for individuals with comparable diets and inhabiting other islands in the Pacific.

  18. Technologically enhanced 210Pb and 210Po in iron and steel industry.

    Science.gov (United States)

    Khater, Ashraf E M; Bakr, Wafaa F

    2011-05-01

    Iron and steel manufacture has been ranked as the largest industrial source of environmental contamination in the USA; the wastes generated in their production processes contain heavy elements that can be a source of contamination, and natural radionuclides that can produce an occupational and/or public radiological impact. In this work the potential occupational effective dose rate (μSv/y) due to inhalation in four integrated steel-making factories from Egypt has been evaluated, by assuming a well defined scenario and with basis in the (210)Pb and (210)Po activity concentrations determined in ore and wastes collected in the aforementioned factories. Activity concentrations, in Bq/kg, of (210)Pb and (210)Po, and leachable Pb and Fe were measured using gamma-ray spectrometry based on HPGe detector, alpha particle spectrometry based on PIPS detector, and inductively coupled plasma-mass spectrometry (ICP-MS). Levels of (210)Pb and (210)Po in the range of

  19. 210Po and 210Pb concentration of cigarettes traded in Hungary and their estimated dose contribution due to smoking

    International Nuclear Information System (INIS)

    Kovacs, Tibor; Somlai, Janos; Nagy, Katalin; Szeiler, Gabor

    2007-01-01

    It is known that tobacco leaves may contain 210 Pb and 210 Po in significant concentrations. The cumulative alpha-radiation dose due to the radioactive content of inhaled cigarette smoke and the increasing number of lung cancer cases explain the importance of the investigation. The present study investigated the activity concentrations of these two radionuclides in 29 Hungarian cigarette samples. The relation between 210 Po/ 210 Pb activity and nicotine/tar content of these cigarettes was also examined. 210 Po was determined by alpha spectrometry using a PIPS detector after chemical leaching and spontaneous deposition of 210 Po on a high nickel-content (25%) stainless steel disk. The 210 Pb activity was calculated from the 210 Po originated from the decay of 210 Pb after a waiting period of eight months. The 210 Po activity concentrations of the measured types of cigarettes ranged from 10.0 to 33.5 mBq/cigarette, and the activity of 210 Pb varied from 9.6 to 32.5 mBq/cigarette. The average annual committed effective dose is estimated to be 185.6±70.6μSv/y and 58.7±22.7μSv/y due to cigarette smoking (20 cigarettes/day) for 210 Po and 210 Pb, respectively

  20. Studies of corrosion resistance of Japanese steels in liquid lead-bismuth

    International Nuclear Information System (INIS)

    Kamata, Kin-ya; Ono, Hiroshi; Kitano, Teruaki; Ono, Mikinori

    2003-01-01

    Liquid lead-bismuth has attractive characteristics as a coolant in future fast reactors and Accelerator Driven Sub-critical Systems (ADS) applications. The corrosion behavior of structural materials in lead-bismuth eutectic is one of key problems in developing nuclear power plants and installations using lead-bismuth coolant. Our experiences with heat exchangers using liquid lead-bismuth and the results of corrosion tests of Japanese steels are reported in this paper. A series of corrosion tests was carried out in collaboration with the Institute of Physics and Power Engineering (IPPE). Test specimens of various Japanese steels were exposed in a non-isothermal forced circulation loop. The influence of maximum temperature and oxygen content in lead bismuth were chosen for study as the primary causes of corrosion in Japanese steels. After the corrosion tests, corrosion behavior was analyzed by visual inspection, measurement of weight loss and metallurgical examination of the microstructure of the corroded zone. The corrosion mechanism in liquid lead bismuth is discussed on the basis of the metallurgical examination of the corroded zone. (author)

  1. Nano sized bismuth oxy chloride by metal organic chemical vapour deposition

    Energy Technology Data Exchange (ETDEWEB)

    Jagdale, Pravin, E-mail: pravin.jagdale@polito.it [Department of Applied Science and Technology (DISAT), Politecnico di Torino, 10129 (Italy); Castellino, Micaela [Center for Space Human Robotics, Istituto Italiano di Tecnologia, Corso Trento 21, 10129 Torino (Italy); Marrec, Françoise [Laboratory of Condensed Matter Physics, University of Picardie Jules Verne (UPJV), Amiens 80039 (France); Rodil, Sandra E. [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexicom (UNAM), Mexico D.F. 04510 (Mexico); Tagliaferro, Alberto [Department of Applied Science and Technology (DISAT), Politecnico di Torino, 10129 (Italy)

    2014-06-01

    Metal organic chemical vapour deposition (MOCVD) method was used to prepare thin films of bismuth based nano particles starting from bismuth salts. Nano sized bismuth oxy chloride (BiOCl) crystals were synthesized from solution containing bismuth chloride (BiCl{sub 3}) in acetone (CH{sub 3}-CO-CH{sub 3}). Self-assembly of nano sized BiOCl crystals were observed on the surface of silicon, fused silica, copper, carbon nanotubes and aluminium substrates. Various synthesis parameters and their significant impact onto the formation of self-assembled nano-crystalline BiOCl were investigated. BiOCl nano particles were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy and Micro-Raman spectroscopy. These analyses confirm that bismuth nanometer-sized crystal structures showing a single tetragonal phase were indeed bismuth oxy chloride (BiOCl) square platelets 18–250 nm thick and a few micrometres wide.

  2. Evaluation of the strength and radiopacity of Portland cement with varying additions of bismuth oxide.

    Science.gov (United States)

    Saliba, E; Abbassi-Ghadi, S; Vowles, R; Camilleri, J; Hooper, S; Camilleri, J

    2009-04-01

    To study the effect of addition of various proportions of bismuth oxide on compressive strength and radiopacity of Portland cement. The compressive strength of white Portland cement and cement replaced with 10, 15, 20, 25 and 30% bismuth oxide was evaluated by testing cylinders 6 mm in diameter and 12 mm high. Twelve cylinders were tested for each material under study. The radiopacity of the cements tested was evaluated using an aluminium step-wedge and densitometer. The optical density was compared with the relevant thickness of aluminium (Al). Statistical analysis was performed using Analysis of Variance (ANOVA) with P = 0.05 and Tukey test to perform multiple comparison tests. Various additions of bismuth oxide had no significant effect on the strength of the material when compared with the unmodified Portland cement (P > 0.05). The radiopacity of the cements tested ranged from 2.02 mm Al for Portland cement to 9.79 mm Al for the highest bismuth replacement. Addition of bismuth oxide did not affect the compressive strength of Portland cement. All the bismuth oxide cement mixtures had radio-opacities higher than 3 mm thickness of aluminium.

  3. Extreme Pressure Synergistic Mechanism of Bismuth Naphthenate and Sulfurized Isobutene Additives

    Science.gov (United States)

    Xu, Xin; Hu, Jianqiang; Yang, Shizhao; Xie, Feng; Guo, Li

    A four-ball tester was used to evaluate the tribological performances of bismuth naphthenate (BiNap), sulfurized isobutene (VSB), and their combinations. The results show that the antiwear properties of BiNap and VSB are not very visible, but they possess good extreme pressure (EP) properties, particularly sulfur containing bismuth additives. Synergistic EP properties of BiNap with various sulfur-containing additives were investigated. The results indicate that BiNap exhibits good EP synergism with sulfur-containing additives. The surface analytical tools, such as X-ray photoelectron spectrometer (XPS) scanning electron microscope (SEM) and energy dispersive X-ray (EDX), were used to investigate the topography, composition contents, and depth profile of some typical elements on the rubbing surface. Smooth topography of wear scar further confirms that the additive showed good EP capacities, and XPS and EDX analyzes indicate that tribochemical mixed protective films composed of bismuth, bismuth oxides, sulfides, and sulfates are formed on the rubbing surface, which improves the tribological properties of lubricants. In particular, a large number of bismuth atoms and bismuth sulfides play an important role in improving the EP properties of oils.

  4. Intrinsic stress of bismuth oxide thin films: effect of vapour chopping and air ageing

    International Nuclear Information System (INIS)

    Patil, R B; Puri, R K; Puri, V

    2008-01-01

    Bismuth oxide thin films of thickness 1000 A 0 have been prepared by thermal oxidation (in air) of vacuum evaporated bismuth thin films (on glass substrate) at different oxidation temperatures and duration. Both the vapour chopped and nonchopped bismuth oxide thin films showed polycrystalline and polymorphic structure. The monoclinic bismuth oxide was found to be predominant in both the cases. The effect of vapour chopping and air exposure for 40 days on the intrinsic stress of bismuth oxide thin films has been studied. The vapour chopped films showed low (3.92 - 4.80 x 10 9 N/m 2 ) intrinsic stress than those of nonchopped bismuth oxide thin films (5.77 - 6.74 x 10 9 N/m 2 ). Intrinsic stress was found to increase due to air ageing. The effect of air ageing on the vapour chopped films was found low. The vapour chopped films showed higher packing density. Higher the packing density, lower the film will age. The process of chopping vapour flow creates films with less inhomogenety i.e. a low concentration of flaws and non-planar defects which results in lower intrinsic stress

  5. Removal of polonium contamination by lead-bismuth eutectic in nuclear systems

    International Nuclear Information System (INIS)

    Miura, Terumitsu; Obara, Toru; Sekimoto, Hiroshi

    2003-01-01

    Lead-Bismuth eutectic (LBE) is considered as a promising candidate of the coolant of liquid metal cooled fast reactor, and the coolant and/or target of accelerator driven system. LBE has various good characters for coolant, but it has also some problems such as polonium production. It is necessary to take polonium contamination into consideration, when LBE is used as the coolant. In the present paper, the removal of contaminating polonium from material surface is studied. Baking method is investigated for polonium removal from contaminated quartz glass plate in vacuum. Before and after baking, the mass of the contaminants on the surface and alpha particle counts from contaminated surface is measured. When the contaminated quartz glass plates are baked at more than 400degC for a few minutes, alpha particle counts from the surface decreases by more than 99.7%, and the mass of contaminants decreases by more than 50%. When the baking was performed at 300degC for 15 minutes and more, alpha particle count decreases by more than 80%, and the mass decreases in little. When, the baking temperature is lower than 200degC, alpha particle counts and mass do not decrease. (author)

  6. Bismuth-boron multiple bonding in BiB_2O"- and Bi_2B"-

    International Nuclear Information System (INIS)

    Jian, Tian; Cheung, Ling Fung; Chen, Teng-Teng; Wang, Lai-Sheng

    2017-01-01

    Despite its electron deficiency, boron is versatile in forming multiple bonds. Transition-metal-boron double bonding is known, but boron-metal triple bonds have been elusive. Two bismuth boron cluster anions, BiB_2O"- and Bi_2B"-, containing triple and double B-Bi bonds are presented. The BiB_2O"- and Bi_2B"- clusters are produced by laser vaporization of a mixed B/Bi target and characterized by photoelectron spectroscopy and ab initio calculations. Well-resolved photoelectron spectra are obtained and interpreted with the help of ab initio calculations, which show that both species are linear. Chemical bonding analyses reveal that Bi forms triple and double bonds with boron in BiB_2O"- ([Bi≡B-B≡O]"-) and Bi_2B"- ([Bi=B=Bi]"-), respectively. The Bi-B double and triple bond strengths are calculated to be 3.21 and 4.70 eV, respectively. This is the first experimental observation of Bi-B double and triple bonds, opening the door to design main-group metal-boron complexes with multiple bonding. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  7. Transfer analysis of 210Po and 210Pb in the terrestrial environment

    International Nuclear Information System (INIS)

    Persson, B.R.R.

    2013-01-01

    The transfer of 210 Po and 210 Pb between various compartments in the terrestrial environment has been analysed by using published data. The average activity concentration of 210 Po in dry soil is 61 ± 14 Bq.kg -1 (median 44 Bq.kg -1 ). Ground water concentrations of 210 Po in drilled wells might be as high as 6.5 Bq/l. But in regular drinking water it is just about 3-5 mBq/l. The uptake of radionuclides from soil to plant is usually given as the ratio of dry matter radionuclide-activity concentrations of plant (AC plant ) and soil (AC soil ) respectively. This ratio is called the soil transfer factor: STF = AC plant /AC soil . The soil transfer factor varies widely between various types of crops with an average of about 0.056±0.003. The activity concentrations in leafy plants are, however highly affected by the atmospheric deposition of 210 Pb and 210 Po. By comparing the activity concentrations in plants grown on an open field with those grown on a field sheltered by a polyethylene tent, it has been possible to estimate a deposition transfer factor: DTF = Difference of the dry matter activity concentration (Bq.kg -1 ) of plant grown in open field and plants grown in tent shelter, divided by the atmospheric deposition during the vegetation period (Bq.m -2 ). The deposition transfer factor for 210 Pb thus estimated is in the order of 0.5-1.0 (m 2 .kg -1 dry matter) for leafy plants like grass and 0.1-0.5 for less leafy plant and straw. For various grains it is < 0.2 and for root fruits it is < 0.003 (m 2 .kg -1 dry matter). Corresponding values for 210 Po are about a factor 3 times higher. The world average activity concentration of 210 Po in fresh leafy vegetable is estimated to 320±190 mBq.kg -1 , and in cereals and grain products 240±80 mBq.kg -1 . The average activity concentration in milk products is 59 ± 13 mBq.kg -1 and in meat products about 70 ± 39 mBq.kg -1 . The dietary intake of milk and meat products is 170 kg.a - which is the highest of all food

  8. Hypoxia induces miR-210, leading to anti-apoptosis in ovarian follicular cells of marine medaka Oryzias melastigma

    International Nuclear Information System (INIS)

    Tse, Anna Chung-Kwan; Li, Jing-Woei; Chan, Ting-Fung; Wu, Rudolf Shiu-Sun; Lai, Keng-Po

    2015-01-01

    Highlights: • We demonstrate hypoxia induced miR-210 in ovarian follicular cells. • We show anti-apoptotic roles of miR-210 in ovarian follicular cells under hypoxia. • Apoptotic genes (DLC1, SLK, TNFRSF10B, RBM25, and USP7) are target of miR-210. • MiR-210 is vital for ovarian follicular cells proliferation in response to hypoxia. - Abstract: Hypoxia is a major global problem that impairs reproductive functions and reduces the quality and quantity of gametes and the fertilization success of marine fish. Nevertheless, the detailed molecular mechanism underlying hypoxia-induced female reproductive impairment remains largely unknown. There is increasing evidence that miRNA is vital in regulating ovarian functions and is closely associated with female fertility in humans. Certain miRNAs that regulate apoptotic genes can be induced by hypoxia, resulting in cell apoptosis. Using primary ovarian follicular cells of the marine medaka, Oryzias melastigma, as a model, we investigated the response of miR-210 to hypoxic stress in ovarian tissues to see if it would interrupt reproductive functions. A significant induction of miR-210 was found in primary ovarian follicular cells exposed to hypoxia, and gene ontology analysis further highlighted the potential roles of miR-210 in cell proliferation, cell differentiation, and cell apoptosis. A number of miR-210 target apoptotic genes, including Deleted in liver cancer 1 protein (DLC1), STE20-like serine/threonine-protein kinase (SLK), tumor necrosis factor receptor superfamily member 10b (TNFRSF10B), RNA binding motif protein 25 (RBM25), and Ubiquitin-specific-processing protease 7 (USP7), were identified. We further showed that ectopic expression of miR-210 would result in down-regulation of these apoptotic genes. On the other hand, the inhibition of miR-210 promoted apoptotic cell death and the expression of apoptotic marker – caspase 3 in follicular cells under hypoxic treatment, supporting the regulatory role of mi

  9. Hypoxia induces miR-210, leading to anti-apoptosis in ovarian follicular cells of marine medaka Oryzias melastigma

    Energy Technology Data Exchange (ETDEWEB)

    Tse, Anna Chung-Kwan [School of Biological Sciences, The University of Hong Kong, Pokfulam Road, Hong Kong SAR (China); State Key Laboratory in Marine Pollution, Hong Kong SAR (China); Li, Jing-Woei; Chan, Ting-Fung [School of Life Sciences, Hong Kong Bioinformatics Centre, The Chinese University of Hong Kong, Hong Kong SAR (China); Wu, Rudolf Shiu-Sun [School of Biological Sciences, The University of Hong Kong, Pokfulam Road, Hong Kong SAR (China); State Key Laboratory in Marine Pollution, Hong Kong SAR (China); Lai, Keng-Po, E-mail: balllai@hku.hk [School of Biological Sciences, The University of Hong Kong, Pokfulam Road, Hong Kong SAR (China); State Key Laboratory in Marine Pollution, Hong Kong SAR (China)

    2015-08-15

    Highlights: • We demonstrate hypoxia induced miR-210 in ovarian follicular cells. • We show anti-apoptotic roles of miR-210 in ovarian follicular cells under hypoxia. • Apoptotic genes (DLC1, SLK, TNFRSF10B, RBM25, and USP7) are target of miR-210. • MiR-210 is vital for ovarian follicular cells proliferation in response to hypoxia. - Abstract: Hypoxia is a major global problem that impairs reproductive functions and reduces the quality and quantity of gametes and the fertilization success of marine fish. Nevertheless, the detailed molecular mechanism underlying hypoxia-induced female reproductive impairment remains largely unknown. There is increasing evidence that miRNA is vital in regulating ovarian functions and is closely associated with female fertility in humans. Certain miRNAs that regulate apoptotic genes can be induced by hypoxia, resulting in cell apoptosis. Using primary ovarian follicular cells of the marine medaka, Oryzias melastigma, as a model, we investigated the response of miR-210 to hypoxic stress in ovarian tissues to see if it would interrupt reproductive functions. A significant induction of miR-210 was found in primary ovarian follicular cells exposed to hypoxia, and gene ontology analysis further highlighted the potential roles of miR-210 in cell proliferation, cell differentiation, and cell apoptosis. A number of miR-210 target apoptotic genes, including Deleted in liver cancer 1 protein (DLC1), STE20-like serine/threonine-protein kinase (SLK), tumor necrosis factor receptor superfamily member 10b (TNFRSF10B), RNA binding motif protein 25 (RBM25), and Ubiquitin-specific-processing protease 7 (USP7), were identified. We further showed that ectopic expression of miR-210 would result in down-regulation of these apoptotic genes. On the other hand, the inhibition of miR-210 promoted apoptotic cell death and the expression of apoptotic marker – caspase 3 in follicular cells under hypoxic treatment, supporting the regulatory role of mi

  10. Extraction of lanthanide elements and bismuth in molten lithium chloride-liquid bismuth-lithium alloy system

    International Nuclear Information System (INIS)

    Harada, Makoto; Adachi, Motonari; Kai, Yuichi; Koike, Kenichi

    1987-01-01

    The equilibrium distributions of neodymium and samarium between molten LiCl and liquid Bi-Li alloy were measured in a wide range of Li-mole fraction in the alloy phase, X Li . These lanthanide elements were extracted through redox reactions. In high X Li range, X Li > 0.03, the distributions of neodymium and bismuth in the salt phase increased markedly. The anomalous increase is attributed to the formation of the compound comprized of Nd, Li, Bi and oxygen in the salt phase. The reaction processes in samarium and neodymium were very fast and the extraction rates are controlled by the diffusion processes of the solutes and metallic lithium. (author)

  11. Separation of 210Pb, 210Bi and 210Po by ion exchange and their Iiquid scintillation standardization; Separacion del 210Pb, 210Bi y 2I0Po mediante columna de cambio ionico y su calibracion por centelleo liquido

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, L.; Jimenez, A.; Grau, A.

    1996-07-01

    We applied the CIEMAT/NIST method and alpha/beta discrimination to ''210Pb samples in equilibrium with its daughters, by preparing homogeneous and gel samples. The stability of samples was tested in different available cocktails, HiSafe''TM II, HiSafe''TM III, Ultima-Gold''TM, Ultima-Gold''TM XR, Ultima-Gold''TM AB, Insta-Gel''R and e Insta-Gel''R lI. Also we analyzed the disequilibrium of the radioactive chain 210Pb+210Bi+210Po, achieving an excellent agreement between the results of the spectrum unfolding method and the experimental values. (Author) 13 refs.

  12. 46 CFR 28.210 - First aid equipment and training.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false First aid equipment and training. 28.210 Section 28.210....210 First aid equipment and training. (a) Each vessel must have on board a complete first aid manual... location. (b) First aid and cardiopulmonary resuscitation (CPR) course certification. Certification in...

  13. 42 CFR 422.210 - Assurances to CMS.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 3 2010-10-01 2010-10-01 false Assurances to CMS. 422.210 Section 422.210 Public...) MEDICARE PROGRAM MEDICARE ADVANTAGE PROGRAM Relationships With Providers § 422.210 Assurances to CMS. (a) Assurances to CMS. Each organization will provide assurance satisfactory to the Secretary that the...

  14. 9 CFR 113.210 - Feline Calicivirus Vaccine, Killed Virus.

    Science.gov (United States)

    2010-01-01

    ... Virus. 113.210 Section 113.210 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE VIRUSES, SERUMS, TOXINS, AND ANALOGOUS PRODUCTS; ORGANISMS AND VECTORS STANDARD REQUIREMENTS Killed Virus Vaccines § 113.210 Feline Calicivirus Vaccine, Killed Virus. Feline Calicivirus...

  15. 29 CFR 99.210 - Subrecipient and vendor determinations.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 1 2010-07-01 2010-07-01 true Subrecipient and vendor determinations. 99.210 Section 99.210 Labor Office of the Secretary of Labor AUDITS OF STATES, LOCAL GOVERNMENTS, AND NON-PROFIT ORGANIZATIONS Audits § 99.210 Subrecipient and vendor determinations. (a) General. An auditee may be a recipient...

  16. 10 CFR 1015.210 - Liquidation of collateral.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Liquidation of collateral. 1015.210 Section 1015.210... for the Administrative Collection of Claims § 1015.210 Liquidation of collateral. (a) DOE may liquidate security or collateral through the exercise of a power of sale in the security instrument or a...

  17. 19 CFR 210.77 - Temporary emergency action.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Temporary emergency action. 210.77 Section 210.77 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Enforcement Procedures and Advisory Opinions § 210.77 Temporary...

  18. 19 CFR 210.48 - Disposition of petitions for reconsideration.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Disposition of petitions for reconsideration. 210.48 Section 210.48 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Determinations and Actions Taken § 210.48...

  19. 19 CFR 210.51 - Period for concluding investigation.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Period for concluding investigation. 210.51 Section 210.51 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Determinations and Actions Taken § 210.51 Period for...

  20. 19 CFR 210.58 - Provisional acceptance of the motion.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Provisional acceptance of the motion. 210.58 Section 210.58 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Temporary Relief § 210.58 Provisional acceptance of...

  1. 19 CFR 210.73 - Review of reports.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Review of reports. 210.73 Section 210.73 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Enforcement Procedures and Advisory Opinions § 210.73 Review of reports. (a...

  2. 19 CFR 210.31 - Requests for admission.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Requests for admission. 210.31 Section 210.31 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Discovery and Compulsory Process § 210.31 Requests for admission. (a...

  3. 19 CFR 210.47 - Petitions for reconsideration.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Petitions for reconsideration. 210.47 Section 210.47 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Determinations and Actions Taken § 210.47 Petitions for...

  4. 19 CFR 210.4 - Written submissions; representations; sanctions.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Written submissions; representations; sanctions. 210.4 Section 210.4 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Rules of General Applicability § 210.4...

  5. 19 CFR 210.72 - Confidentiality of information.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Confidentiality of information. 210.72 Section 210.72 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Enforcement Procedures and Advisory Opinions § 210.72...

  6. 19 CFR 210.74 - Modification of reporting requirements.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Modification of reporting requirements. 210.74 Section 210.74 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Enforcement Procedures and Advisory Opinions § 210.74...

  7. 19 CFR Appendix A to Part 210 - Adjudication and Enforcement

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Adjudication and Enforcement A Appendix A to Part 210 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Pt. 210, App. A Appendix A to Part 210—Adjudication and...

  8. 19 CFR 210.57 - Amendment of the motion.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Amendment of the motion. 210.57 Section 210.57 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Temporary Relief § 210.57 Amendment of the motion. A motion for...

  9. 19 CFR 210.36 - General provisions for hearings.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false General provisions for hearings. 210.36 Section 210.36 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Prehearing Conferences and Hearings § 210.36 General...

  10. 19 CFR 210.61 - Discovery and compulsory process.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Discovery and compulsory process. 210.61 Section 210.61 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Temporary Relief § 210.61 Discovery and compulsory...

  11. 19 CFR 210.5 - Confidential business information.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Confidential business information. 210.5 Section 210.5 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Rules of General Applicability § 210.5 Confidential...

  12. 19 CFR 210.65 - Certification of the record.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Certification of the record. 210.65 Section 210.65 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Temporary Relief § 210.65 Certification of the record. When the...

  13. 19 CFR 210.27 - General provisions governing discovery.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false General provisions governing discovery. 210.27 Section 210.27 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Discovery and Compulsory Process § 210.27 General...

  14. 19 CFR 210.23 - Suspension of investigation.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Suspension of investigation. 210.23 Section 210.23 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Motions § 210.23 Suspension of investigation. Any party may move to...

  15. 19 CFR 210.41 - Termination of investigation.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Termination of investigation. 210.41 Section 210.41 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Determinations and Actions Taken § 210.41 Termination of...

  16. 19 CFR 210.53 - Motion filed after complaint.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Motion filed after complaint. 210.53 Section 210.53 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Temporary Relief § 210.53 Motion filed after complaint. (a) A...

  17. 19 CFR 210.20 - Declassification of confidential information.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Declassification of confidential information. 210.20 Section 210.20 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Motions § 210.20 Declassification of...

  18. 19 CFR 210.49 - Implementation of Commission action.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Implementation of Commission action. 210.49 Section 210.49 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Determinations and Actions Taken § 210.49...

  19. 19 CFR 210.55 - Content of service copies.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Content of service copies. 210.55 Section 210.55 Customs Duties UNITED STATES INTERNATIONAL TRADE COMMISSION INVESTIGATIONS OF UNFAIR PRACTICES IN IMPORT TRADE ADJUDICATION AND ENFORCEMENT Temporary Relief § 210.55 Content of service copies. (a) Any...

  20. 21 CFR 107.210 - Firm-initiated product removals.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Firm-initiated product removals. 107.210 Section 107.210 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION INFANT FORMULA Infant Formula Recalls § 107.210 Firm-initiated product...

  1. 7 CFR 210.16 - Food service management companies.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Food service management companies. 210.16 Section 210... Authority Participation § 210.16 Food service management companies. (a) General. Any school food authority... management company to manage its food service operation in one or more of its schools. However, no school or...

  2. 7 CFR 3565.210 - Maximum interest rate.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Maximum interest rate. 3565.210 Section 3565.210... AGRICULTURE GUARANTEED RURAL RENTAL HOUSING PROGRAM Loan Requirements § 3565.210 Maximum interest rate. The interest rate for a guaranteed loan must not exceed the maximum allowable rate specified by the Agency in...

  3. 22 CFR 210.635 - Drug-free workplace.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Drug-free workplace. 210.635 Section 210.635 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT GOVERNMENTWIDE REQUIREMENTS FOR DRUG-FREE WORKPLACE (FINANCIAL ASSISTANCE) Definitions § 210.635 Drug-free workplace. Drug-free workplace means a site for the...

  4. 7 CFR 210.11 - Competitive food services.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Competitive food services. 210.11 Section 210.11 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF... Participation § 210.11 Competitive food services. (a) Definitions. For the purpose of this section: (1...

  5. Improved optimum condition for recovery and measurement of 210 ...

    African Journals Online (AJOL)

    The aim of this study was to determine the optimum conditions for deposition of 210Po and evaluate the accuracy and precision of the results for its determination in environmental samples. To improve the technique for measurement of polonium-210(210Po) in environmental samples. The optimization of five factors (volume ...

  6. The 210Pb technique for dating sediments, and some applications

    International Nuclear Information System (INIS)

    Eakins, J.D.

    1983-01-01

    The use of 210 Pb for dating sediment in time scale 100-150 years is described. Various methods of determination of 210 Pb concentration are reviewed and the problem of the initial 210 Pb concentration using two models for interpretation of data is discussed. (author)

  7. Measurements and FLUKA Simulations of Bismuth, Aluminium and Indium Activation at the upgraded CERN Shielding Benchmark Facility (CSBF)

    Science.gov (United States)

    Iliopoulou, E.; Bamidis, P.; Brugger, M.; Froeschl, R.; Infantino, A.; Kajimoto, T.; Nakao, N.; Roesler, S.; Sanami, T.; Siountas, A.; Yashima, H.

    2018-06-01

    The CERN High energy AcceleRator Mixed field (CHARM) facility is situated in the CERN Proton Synchrotron (PS) East Experimental Area. The facility receives a pulsed proton beam from the CERN PS with a beam momentum of 24 GeV/c with 5·1011 protons per pulse with a pulse length of 350 ms and with a maximum average beam intensity of 6.7·1010 protons per second. The extracted proton beam impacts on a cylindrical copper target. The shielding of the CHARM facility includes the CERN Shielding Benchmark Facility (CSBF) situated laterally above the target that allows deep shielding penetration benchmark studies of various shielding materials. This facility has been significantly upgraded during the extended technical stop at the beginning of 2016. It consists now of 40 cm of cast iron shielding, a 200 cm long removable sample holder concrete block with 3 inserts for activation samples, a material test location that is used for the measurement of the attenuation length for different shielding materials as well as for sample activation at different thicknesses of the shielding materials. Activation samples of bismuth, aluminium and indium were placed in the CSBF in September 2016 to characterize the upgraded version of the CSBF. Monte Carlo simulations with the FLUKA code have been performed to estimate the specific production yields of bismuth isotopes (206 Bi, 205 Bi, 204 Bi, 203 Bi, 202 Bi, 201 Bi) from 209 Bi, 24 Na from 27 Al and 115 m I from 115 I for these samples. The production yields estimated by FLUKA Monte Carlo simulations are compared to the production yields obtained from γ-spectroscopy measurements of the samples taking the beam intensity profile into account. The agreement between FLUKA predictions and γ-spectroscopy measurements for the production yields is at a level of a factor of 2.

  8. Distribution and enrichment of 210Po and 210Pb in the environment of Mangalore, South West coast of India

    International Nuclear Information System (INIS)

    Prakash, V.; Rajashekara, K.M.; Narayana, Y.

    2013-01-01

    The paper deals with the distribution and enrichment of 210 Po and 210 Pb in soil samples of Mangalore South west coast of India. The soil samples collected from the region were analyzed for 210 Po and 210 Pb activity using radiochemical analytical techniques to understand the distribution and enrichment of those radionuclides. The 210 Po activity in soil in the environment of Mangalore varies from 1.5 Bq kg -1 to 26.9 Bq kg -1 with a mean value of 12.6 Bq kg -1 and that of 210 Pb varies in the range 7.6 Bq kg -1 to 67.5 Bq kg -1 with a mean value of 38.9 Bq kg -1 . The mean 210 Po/ 210 Pb ratio observed was 0.3 and it shows that the radionuclides 210 Po and 210 Pb are not in equilibrium and the accumulation of 210 Pb in soil is more compared to 210 Po. A good correlation exists between the activities of 210 Po and 210 Pb with correlation coefficient r = 0.7. The absorbed gamma dose in the environment of the region varies from 39.4 nGy h -1 to 78.8 nGy h -1 with a mean value of 48.2 nGy h -1 . The results of the systematic studies on the distribution and enrichment of 210 Po and 210 Pb and the absorbed gamma dose rate in air are presented and discussed in this paper. (author)

  9. Distribution of 210Pb and 210Po concentrations in wild berries and mushrooms in boreal forest ecosystems

    International Nuclear Information System (INIS)

    Vaaramaa, Kaisa; Solatie, Dina; Aro, Lasse

    2009-01-01

    The activity concentrations and distribution of 210 Pb and 210 Po in wild berries and edible mushrooms were investigated in Finnish forests. The main study areas were located in Scots pine (Pinus sylvestris L.) forests in southern and northern Finland. The activity concentrations of 210 Pb and 210 Po in blueberry (Vaccinium myrtillus L.) and lingonberry (Vaccinium vitis-idaea L.) samples decreased in the order: stems > leaves > berries (i.e. fruits). The activity ratios of 210 Po/ 210 Pb in the wild berry samples were mainly higher than one, indicating elevated activity concentrations of polonium in the samples. In mushrooms the activity concentrations of 210 Pb and especially 210 Po were higher than in fruits of the wild berries. The highest activity concentration of 210 Pb was detected in Cortinarius armillatus L. (16.2 Bq kg -1 d.w.) and the lowest in Leccinum vulpinum L. (1.38 Bq kg -1 d.w.). The 210 Po activity concentrations of the whole fruiting bodies ranged from 7.14 Bq kg -1 d.w. (Russula paludosa L.) to 1174 Bq kg -1 d.w. (L. vulpinum L.). In general, the highest activity concentrations of 210 Po were recorded in boletes. The caps of mushrooms of the Boletaceae family showed higher activity concentrations of 210 Po compared to the stipes. In most of the mushrooms analyzed, the activity concentrations of 210 Po were higher than those of 210 Pb. 210 Po and 210 Pb dominate the radiation doses received via ingestion of wild berries and mushrooms in northern Finland, while in southern Finland the ingested dose is dominated by 137 Cs from the Chernobyl fallout.

  10. Distribution of {sup 210}Pb and {sup 210}Po concentrations in wild berries and mushrooms in boreal forest ecosystems

    Energy Technology Data Exchange (ETDEWEB)

    Vaaramaa, Kaisa, E-mail: Kaisa.Vaaramaa@Helsinki.fi [Laboratory of Radiochemistry, Department of Chemistry, P.O. Box 55, FI-00014 University of Helsinki (Finland); Solatie, Dina [STUK-Radiation and Nuclear Safety Authority, Regional Laboratory in Northern Finland, FI-96500 Rovaniemi (Finland); Aro, Lasse [Finnish Forest Research Institute (METLA), Parkano Research Unit, FI-39700 Parkano (Finland)

    2009-12-15

    The activity concentrations and distribution of {sup 210}Pb and {sup 210}Po in wild berries and edible mushrooms were investigated in Finnish forests. The main study areas were located in Scots pine (Pinus sylvestris L.) forests in southern and northern Finland. The activity concentrations of {sup 210}Pb and {sup 210}Po in blueberry (Vaccinium myrtillus L.) and lingonberry (Vaccinium vitis-idaea L.) samples decreased in the order: stems > leaves > berries (i.e. fruits). The activity ratios of {sup 210}Po/{sup 210}Pb in the wild berry samples were mainly higher than one, indicating elevated activity concentrations of polonium in the samples. In mushrooms the activity concentrations of {sup 210}Pb and especially {sup 210}Po were higher than in fruits of the wild berries. The highest activity concentration of {sup 210}Pb was detected in Cortinarius armillatus L. (16.2 Bq kg{sup -1} d.w.) and the lowest in Leccinum vulpinum L. (1.38 Bq kg{sup -1} d.w.). The {sup 210}Po activity concentrations of the whole fruiting bodies ranged from 7.14 Bq kg{sup -1} d.w. (Russula paludosa L.) to 1174 Bq kg{sup -1} d.w. (L. vulpinum L.). In general, the highest activity concentrations of {sup 210}Po were recorded in boletes. The caps of mushrooms of the Boletaceae family showed higher activity concentrations of {sup 210}Po compared to the stipes. In most of the mushrooms analyzed, the activity concentrations of {sup 210}Po were higher than those of {sup 210}Pb. {sup 210}Po and {sup 210}Pb dominate the radiation doses received via ingestion of wild berries and mushrooms in northern Finland, while in southern Finland the ingested dose is dominated by {sup 137}Cs from the Chernobyl fallout.

  11. Neutron activation determination of impurities in high-purity bismuth with separation of matrix in form of hydroxide

    International Nuclear Information System (INIS)

    Artyukhin, P.I.; Shavinskij, B.M.; Mityakin, Yu.L.

    1979-01-01

    The technique of neutron activation determination of 15 impurity elements (Au, Ag, Ba, Cd, Co, Cs, Cu, Hg, K, Na, Ni, Se, Sr, Te, Zn) in high-purity bismuth (impurity content is approximately 10 -6 -10 -10 %) is presented. Bismuth hydroxide precipitation by ammonia from nitric acid solutions was used to separate bismuth from alkali, alkaline earth metals and elements forming stable ammines. Gold, selenium and tellurium are isolated in the form of metals at reduction by muriatic hydrazine. Results of analyzing two samples of special purity bismuth are presented. Neutron flux comprised 0.8-1x10 13 n/cm 2 xs. Radiation time was equal to 90 hours

  12. 210Pb dating of Baltic Sea sediments

    International Nuclear Information System (INIS)

    Gellermann, R.

    1990-01-01

    The paper reports on the results of 210 Pb measurement in sediment cores from the Baltic Sea. The models used for the interpretation are derived and discussed. In general, the sedimentation parameters calculated with different models are consistent. However, parameters of cores independently taken on same partly show clearly differing values. The reasons of this observation have to be analysed by further studies. An essential problem considered in this paper is the dating of disturbed sediments. The use of such cores for the reconstruction of the input history of chemical indicators requires a deconvolution of data. The response function necessary for this procedure can be derived from 210 Pb measurements. The results of such a reconstruction considerably differ from those obtained by conventional dating models. The analysis of the measuring uncertainty of the indicator (e.g. lead) in the deconvolution procedure unveals the limits of the method and prevents it from overinterpretation. (orig.) [de

  13. Separation and electrodeposited of 210 Po

    International Nuclear Information System (INIS)

    Ordonez R, E.; Iturbe G, J.L.

    1991-12-01

    Presently work it was determined the selective separation of the 210 Po that is in an uraniferous mineral, by means of acid leaching of the mineral and the purification was carried out by means of partition chromatography whose stationary phase is 2-ethylhexyl phosphoric acid (D 2 EHPA), it has been possible to isolate the 210 Po of the rest of the radioactive elements that conform the family 4 N +2 , the optimal elutriation conditions of this element were settled down of manner of not dragging other radioelements. Another of the achievements presented in this communication has been the electrodeposition of this element has more than enough stainless steel discs with a superior yield to 95%. (Author)

  14. 210Pb and 210Po determination in environmental samples using liquid scintillation counting and alpha spectrometry

    International Nuclear Information System (INIS)

    Sanchez, D.P.; Sanchez, A.M.; Vargas, M.J.

    2002-01-01

    A simple radiochemical procedure has been developed to determine 210 Pb and 210 Po in environmental samples. After adding 209 Po tracer and Pb carrier, an aliquot of the sample is decomposed by microwave digestion or by evaporation with mineral acids (depending on the expected activity of the sample). Part of the leaching solution must be used for 210 Po determination, preparing a polonium source by spontaneous deposition onto a nickel disk. The quantitative recoveries are determined using a standard 209 Po tracer, and the activity concentration is determined by isotopic dilution alpha spectrometry. The remaining part of the leaching solution is used for 210 Pb determination by means of two alternative methods: lead can be retained from 1.5 M HCl by the DOWEX 1 X 8, Cl - form resin in a chromatographic column, and stripped with deionised water, or it can be separated by solvent extraction as a lead bromide complex with the organic compound ALIQUAT-336 in toluene (this second method is used preferably in water samples). The Pb source for measurement is prepared by precipitation as oxalate and the chemical recovery determined by gravimetry. The activity concentration of 210 Pb is calculated from the spectra measured with a liquid scintillation spectrometer. Several certified material samples supplied by IAEA were analysed to check the procedure. The measured values for 210 Pb and 210 Po were in good agreement with the certified values presenting deviations lower than 5%. Several environmental samples (river and well waters and also sediments) from zones impacted by Uranium mine exploitation were analysed using the described procedure. The mean yields of Pb and Po were (70 ± 10)% and (81 ± 7)% for waters and (70 ± 12)% and (77 ± 8)% for sediments. (author)

  15. Improved analytical procedure for the determination of 210Pb and 210Po using alpha-spectrometric isotope dilution

    International Nuclear Information System (INIS)

    Urnezis, P.W.; Holtzman, R.B.

    1981-01-01

    An isotope dilution method has been incorporated into the 210 Pb- 210 Po analysis. A known amount of 209 Po is added to the sample before analysis. Then both 209 Po and 210 Po are deposited on a silver planchet which is assayed in an alpha spectrometer to determine the activities of each isotope. The recoveries generally range from 70% to 90%

  16. An assessment of 210Pb and 210Po in terrestrial foodstuffs from regions of England and Wales

    International Nuclear Information System (INIS)

    McDonald, P.; Jackson, D.; Leonard, D.R.P.; McKay, K.

    1999-01-01

    Based on data for nationally available foodstuffs, naturally occurring 210 Pb and 210 Po contribute significantly to the UK radiation dose from dietary intake. To provide a more complete overview of radiological implications to the public, samples of offal, cereal, fruit, root and green vegetables were collected from 11 sites, including regions of potential 210 Pb and 210 Po enhancement. Considerable variability was evident in levels of 210 Pb and 210 Po from all sites and in all food types investigated. Higher concentrations were typically found in offal and cereals. Lowest concentrations were generally found in root vegetables. Between sites, the only evidence of elevated concentrations of 210 Po occurred at Helston ( 210 Po 3.0 Bq kg -1 in bovine liver, no other offal sample exceeding 0.8 Bq kg -1 ), and Holyhead 210 Po 0.4 Bq kg -1 in blackberries, no other fruit sample exceeding 0.1 Bq kg -1 ). Other foodstuffs from these sites did not show similar enhanced levels of 210 Po. The maximum dose arising from consumption of 210 Pb and 210 Po in foods surveyed in this study is estimated to be around 120 μSv year -1 to adults. This compares with an estimated UK average consumption dose from all nuclides and foodstuffs of 300 μSv year -1 (broad range 100-1000 μSv year -1 ). (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

  17. 210Pb content in phytocoenoses with cranberry

    International Nuclear Information System (INIS)

    Dushanskene-Duzh, R.F.; Butkus, V.F.

    1983-01-01

    The purpose of the paper is to study 210 Pb concentration levels in different biotopes of cranberry growing (Oxycoccus palustris Pers.), to determine concentration distribution of this radionuclide over the organs of this plant and to reveal the effect of ecological conditions on concentration levels. Material is collected in southern Lithua in five biotopes in the form of certain belts of plant communities: reed brushwood (mesotrophic place of groWth), lake mire (mesotrophic place of growing), grassy-forest belt (oligotropic bog), forest belt (low slope of the upper ologotrophic bog), head mire (central part of oligotrophic bog). It is stated that levels and distribution of 210 Pb concentration in cranberry organs growing in oligotrophic and mesotrophic biotopes are approximately equal. Its largest part is concentrated in roots, then come shoots with leaves and only negligible part falls on fruits. Direct correlation exists between 210 Pb concentration in roots and shoots with leaves, and back correlation exists between shoots with leaves and fruits

  18. The Litvinenko 210polonium case. German experiences

    International Nuclear Information System (INIS)

    Kroeger, Emily Alice

    2009-01-01

    The high scientific standards of the BfS were necessary in order to characterize and evaluate the low activities of 210 Po found during the deployment in Hamburg. The evaluation of the measurements enabled the BfS to offer effective radiation protection advice and to assist the police investigation. The majority of the 210 Po traces were found in places that had been in skin contact with Kovtun, leading to the conclusion that Kovtun had most probably incorporated 210 Po before his visit to Hamburg in October 2006. As yet, no formal charges have been brought by the German authorities against Kovtun and the costs of the operation remain under discussion. Strategies to improve the internal and external deployment communication of the ZUB are being developed and implemented to deal with both the real and the perceived threats that occur during such an incident. Open communication from the onset of a deployment is essential, both between the institutions involved and between deployment leaders and the press. This will save precious time and resources, lower anxiety in the public and emergency workers and could, in a culture of trust where radiation protection advice is listened to and followed, ultimately save lives. (orig.)

  19. Distribution of lead, Pb 210 in Kuala Muda sediment

    International Nuclear Information System (INIS)

    Jalal Sharib; Zaharudin Ahmad; Yii Mei Wo; Ahmad Sanadi Abu Bakar; Norfaizal Mohamed; Kamarozaman Ishak; Zulkifli Daud

    2008-08-01

    Activity of lead-210, Pb 210 concentration and their distributions in the core sediment from coastal area of Kuala Muda, Kedah was carried out using alpha spectrometry system. The sampling of core sediment for this study was carried out in stages from June 2007 - Nov 2007 as part of Post-Tsunami Environment Impact Assessment Project. The results show that the distribution of lead-210 activity, Pb 210 in core sediment is not consistent and the profiles show no discernable trend. This fluctuation is due to high sedimentation rates and sample disturbance. Compared to previous measurement of nearby area, current results show some increase of Pb 210 activity. (Author)

  20. Measurement of 210Po in vegetables of Gudalore

    International Nuclear Information System (INIS)

    Selvasekarapandian, S.; Sivakumar, R.; Mugunthamanikandan, N.; Ragunath, V.M.; Meenashisundaram, V.

    1999-01-01

    Intake of 210 Po with food was determined for the population in Gudalore taluka of Nilgiri district. The content of 210 Po in different vegetable samples was determined. The annual intake of 210 Po due different vegetables was estimated on the basis of their average annual consumption. The intake of 210 Po varied from 0.056 to 11.97 Bq/kg. The largest intake of 210 Po was with tapioca. From the intake annual effective dose was calculated. Effective dose equivalent due to polonium in different vegetables varied between 0.0121 to 2.872 μSv/Y. (author)

  1. /sup 210/Pb and /sup 210/Po in liver and kidneys of cattle. 1. Animals from an area with little traffic or industry

    Energy Technology Data Exchange (ETDEWEB)

    Bunzl, K; Kracke, W [Gesellschaft fuer Strahlen- und Umweltforschung m.b.H., Neuherberg (Germany, F.R.). Inst. fuer Strahlenschutz; Kreuzer, W

    1979-09-01

    The concentrations of /sup 210/Pb, /sup 210/Po and stable lead were determined in liver and kidneys of 40 animals from a mainly agricultural region with little traffic or industry. Median liver concentrations of 18.0 pCi /sup 210/Pb and 33.3 pCi /sup 210/Po per wet tissue, and median kidney concentrations of 44.0 pCi /sup 210/Pb and 178.5 pCi /sup 210/Po/kg wet tissue were observed. The specific activity of /sup 210/Pb was 161 and 132 nCi /sup 210/Pb/g Pb in liver and kidneys, respectively. On the average, the kidneys contained 2.37 more /sup 210/Pb, 5.05 more /sup 210/Po and 2.89 more Pb than the livers. The ratio /sup 210/Po//sup 210/Pb was 2.18 in the liver and 3.95 in the kidneys. Correlation analysis revealed significant correlations between /sup 210/Po in liver and kidneys, Pb in liver and kidneys, /sup 210/Po and /sup 210/Pb in kidneys, /sup 210/Pb and Pb in liver, /sup 210/Pb and Pb in kidneys, /sup 210/Po and Pb in liver, as well as /sup 210/Po and Pb in kidneys. No significant correlation was observed between the concentrations of either /sup 210/Po or /sup 210/Pb in liver or kidneys and the age of the animals.

  2. Assessment of 210Po exposure for the Italian population

    International Nuclear Information System (INIS)

    Clemente, G.F.; Renzetti, A.; Santori, G.; Breuer, F.

    1980-01-01

    A summary is given of the data required to evaluate the 210 Po internal burden and the relative dose given to the members of the Italian general public and to those groups of subjects who are exposed in non-uranium mines and spas to high radon and daughter product air concentrations. Data on the daily intake, daily excretion, total body burden and skeletal burden of 210 Pb and 210 Po for the general public provide the components of the 210 Pb- 210 Po metabolic balance. A mathematical model has been developed on the basis of this data and can be used to evaluate the 210 Pb- 210 Po body burden of subjects exposed to high levels of radon and daughter products on the basis of their 210 Pb- 210 Po daily excretion. Data is presented for the 210 Pb- 210 Po skeletal and soft tissue burden and the yearly dose rate to the skeleton in non-smokers, smokers, non-uranium miners and spa employees. (UK)

  3. Temporal changes of 210Po in temperate coastal waters

    International Nuclear Information System (INIS)

    Wildgust, M.A.; White, K.N.; McDonald, P.

    1998-01-01

    The temporal variation of Polonium-210 ( 210 Po) was examined in coastal sea water, the mussel Mytilus edulis, the winkle Littorina littorea and green algae Ulva lactuca in order to investigate the entry of 210 Po into the marine food chain. More than 99% of 210 Po in the water column occurred in the particulate phase. Dissolved 210 Po concentrations peaked during the spring phytoplankton bloom and it is suggested this is related to preferential scavenging of 210 Po by the increased numbers of bacteria, viruses and small dissolved particulates. Changes in L. Littorea 210 Po specific activity are thought not to be related to food, but to a drop in body weight following spawning. Much of the 210 Po accumulated by M. edulis was located in the digestive gland. The specific activity of 210 Po in the digestive gland of M. edulis was shown to be strongly correlated with changes in sea water suspended particulate specific activity. Examination of other trace metal (Ag, Al, As, Ca, Cd, Cr, Co, Cu, Fe, Hg, K, Mg, Mn, Na, Ni Sb, Se, Sn and Zn) variations in the digestive gland revealed that class B and borderline metals had a strong positive correlation with 210 Po. On-going work is investigating whether the accumulation and loss of 210 Po is affected by the presence of metallothioneins

  4. Temporal changes of 210Po in temperate coastal waters.

    Science.gov (United States)

    Wildgust, M A; McDonald, P; White, K N

    1998-06-18

    The temporal variation of Polonium-210 (210Po) was examined in coastal sea water, the mussel Mytilus edulis, the winkle Littorina littorea and green alga Ulva lactuca in order to investigate the entry of 210Po into the marine food chain. More than 99% of 210Po in the water column occurred in the particulate phase. Dissolved 210Po concentrations peaked during the spring phytoplankton bloom and it is suggested this is related to preferential scavenging of 210Po by the increased numbers of bacteria, viruses and small dissolved particulates. Changes in L. littorea 210Po specific activity are thought not to be related to food, but to a drop in body weight following spawning. Much of the 210Po accumulated by M. edulis was located in the digestive gland. The specific activity of 210Po in the digestive gland of M. edulis was shown to be strongly correlated with changes in sea water suspended particulate specific activity. Examination of other trace metal (Ag, Al, As, Ca, Cd, Cr, Co, Cu, Fe, Hg, K, Mg, Mn, Na, Ni, Sb, Se, Sn and Zn) variations in the digestive gland revealed that class B and borderline metals had a strong positive correlation with 210Po. On-going work is investigating whether the accumulation and loss of 210Po is affected by the presence of metallothioneins.

  5. Dissolved {sup 210}Po and {sup 210}Pb in Guarani aquifer groundwater, Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Bonotto, D.M. [Departamento de Petrologia e Metalogenia, Universidade Estadual Paulista (UNESP), Av. 24-A No. 1515, C.P. 178, CEP 13506-900 Rio Claro, Sao Paulo (Brazil)], E-mail: danielbonotto@yahoo.com.br; Caprioglio, L.; Bueno, T.O.; Lazarindo, J.R. [Departamento de Petrologia e Metalogenia, Universidade Estadual Paulista (UNESP), Av. 24-A No. 1515, C.P. 178, CEP 13506-900 Rio Claro, Sao Paulo (Brazil)

    2009-03-15

    The huge Guarani aquifer located in the South American continent is a very important resource for the region, and its drinking water quality has been investigated according to international standards, inclusive radiological parameters. This paper describes {sup 210}Po and {sup 210}Pb activity concentration data in groundwater samples collected at the Brazilian portion of Guarani aquifer, that is characterized by a great variability of temperature (18-70 deg. C), pH (4.0-9.9), sodium content (0.3-322 mg/l), bicarbonate content (0.1-318 mg/l), etc. Non-expensive alpha counting following some radiochemical steps for extracting and depositing dissolved {sup 210}Po was used. The results of the measurements for samples collected in duplicate yielded a maximum {sup 210}Po activity concentration of 3.7 mBq/L and a maximum {sup 210}Pb activity concentration of 6.7 mBq/l, that are values greatly lower than the guidance level of 0.1 Bq/l established by the WHO for their presence in drinking water. The high sensitivity of the method allowed its applicability on the identification of complexes geochemical and hydrogeological processes occurring in Guarani aquifer as well on the evaluation of the drinking water quality in terms of dose calculations.

  6. Dissolved 210Po and 210Pb in Guarani aquifer groundwater, Brazil

    International Nuclear Information System (INIS)

    Bonotto, D.M.; Caprioglio, L.; Bueno, T.O.; Lazarindo, J.R.

    2009-01-01

    The huge Guarani aquifer located in the South American continent is a very important resource for the region, and its drinking water quality has been investigated according to international standards, inclusive radiological parameters. This paper describes 210 Po and 210 Pb activity concentration data in groundwater samples collected at the Brazilian portion of Guarani aquifer, that is characterized by a great variability of temperature (18-70 deg. C), pH (4.0-9.9), sodium content (0.3-322 mg/l), bicarbonate content (0.1-318 mg/l), etc. Non-expensive alpha counting following some radiochemical steps for extracting and depositing dissolved 210 Po was used. The results of the measurements for samples collected in duplicate yielded a maximum 210 Po activity concentration of 3.7 mBq/L and a maximum 210 Pb activity concentration of 6.7 mBq/l, that are values greatly lower than the guidance level of 0.1 Bq/l established by the WHO for their presence in drinking water. The high sensitivity of the method allowed its applicability on the identification of complexes geochemical and hydrogeological processes occurring in Guarani aquifer as well on the evaluation of the drinking water quality in terms of dose calculations.

  7. Determination of {sup 210}Pb and other radionuclides; Determinacion de {sup 210}Pb y otros radionuclidos

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Orellana, Jordi [Universitat Autonoma de Barcelona (Spain)

    2012-07-01

    {sup 210}Pb is an {beta}-{gamma} emitter, with two emissions of {beta} E{sub 1max} = 63.1 keV energies and E{sub 2max} = 16.6 keV {gamma} emission of 46.5 keV. Being twice emitter allows direct determination by different techniques, but also can determine its activity indirectly through its descendant the {sup 210}Po. The most common technique recommended for determining the {sup 210}Pb in coastal sediments is a measure of {sup 210}Po spectrometric {alpha}. In these records we can assume that the {sup 210}Pb and its descendant {sup 210}Po are in secular equilibrium, although the possibility exists that in the upper core this is not always met. The advantages of this technique are that i) radiochemical processing of samples is not complicated, ii) {alpha} spectrometers allow fast counting to obtain acceptable statistics (<10%) and iii) the amount of sample required is small (0.2 to 1 g). The ease of handling samples and the simplicity of spectral treatment allows exploratory profiles of the cores to determine the quality of sedimentary profile before the onset of other analysis. Direct measurement of the {sup 210}Pb {gamma} spectrometry with Ge detectors of high resolution is also very common. Advantages of this technique are that: - it is a nondestructive technique and thus allows reuse of other samples for analysis - preparation of measurement geometries is simple and requires no radiochemical processes; - allows simultaneous measurement of other {gamma} radionuclides of interest ({sup 137}Cs, {sup 241}Am, {sup 226}Ra, {sup 40}K and {sup 23} {sup 4}Th). There are also some disadvantages: - high cost of measurement systems and need for low background shields without {sup 210}Pb; - calibration of the equipment is complex in the area of {sup 210}Pb; - low efficiencies that require long counting time to obtain acceptable statistics (<10%); - need to have at least 5 g of sample well detectors and at least about 20 g for coaxial detectors, although some authors use

  8. Corrosion behavior of Si-enriched steels for nuclear applications in liquid lead–bismuth

    Energy Technology Data Exchange (ETDEWEB)

    Kurata, Yuji, E-mail: kurata.yuji@jaea.go.jp [Japan Atomic Energy Agency, Tokai-mura, Ibaraki-ken 319-1195 (Japan)

    2013-06-15

    Highlights: ► The corrosion behavior of Si-enriched steels in liquid lead–bismuth was studied. ► The corrosion tests were conducted at the two controlled oxygen levels. ► The Si addition reduces the scale thickness under the high oxygen condition. ► The Si addition has no significant effect under the low oxygen condition. -- Abstract: The corrosion behavior of Si-enriched steels in liquid lead–bismuth was studied in order to develop accelerator driven systems for transmutation of long-lived radioactive wastes and lead–bismuth cooled fast reactors. The corrosion tests of 316SS, Si-enriched 316SS, Mod.9Cr–1Mo steel (T91) and Si-enriched T91 were conducted at 550 °C in liquid lead–bismuth at the two controlled oxygen levels. Both the additions of 2.5 wt.% Si to 316SS and 1.5 wt.% Si to T91 had the effect of reducing the thickness of oxide layer in liquid lead–bismuth at the high oxygen concentration (2.5 × 10{sup −5} wt.%). Although the Si addition to 316SS reduced the depth of ferritization caused by Ni dissolution in liquid lead–bismuth at the low oxygen concentration (4.4 × 10{sup −8} wt.%), it could not suppress the ferritization and the penetration of Pb and Bi completely. The Si addition to T91 did not have the effect of preventing the penetration of Pb and Bi in the liquid lead–bismuth at the low oxygen concentration. The oxide scales formed on both Si-enriched steels did not have sufficient corrosion resistance under the low oxygen condition.

  9. Zerovalent bismuth nanoparticles inhibit Streptococcus mutans growth and formation of biofilm

    Directory of Open Access Journals (Sweden)

    Hernandez-Delgadillo R

    2012-04-01

    Full Text Available Rene Hernandez-Delgadillo1, Donaji Velasco-Arias2, David Diaz2, Katiushka Arevalo-Niño1, Marianela Garza-Enriquez1, Myriam A De la Garza-Ramos1, Claudio Cabral-Romero11Instituto de Biotecnologia, Centro de Investigacion y Desarrollo en Ciencias de la Salud, CIDICS, Facultad de Odontologia, Universidad Autonoma de Nuevo Leon, UANL, Monterrey, Nuevo Leon, 2Facultad de Quimica, Universidad Nacional Autonoma de Mexico, Distrito Federal, MexicoBackground and methods: Despite continuous efforts, the increasing prevalence of resistance among pathogenic bacteria to common antibiotics has become one of the most significant concerns in modern medicine. Nanostructured materials are used in many fields, including biological sciences and medicine. While some bismuth derivatives has been used in medicine to treat vomiting, nausea, diarrhea, and stomach pain, the biocidal activity of zerovalent bismuth nanoparticles has not yet been studied. The objective of this investigation was to analyze the antimicrobial activity of bismuth nanoparticles against oral bacteria and their antibiofilm capabilities.Results: Our results showed that stable colloidal bismuth nanoparticles had 69% antimicrobial activity against Streptococcus mutans growth and achieved complete inhibition of biofilm formation. These results are similar to those obtained with chlorhexidine, the most commonly used oral antiseptic agent. The minimal inhibitory concentration of bismuth nanoparticles that interfered with S. mutans growth was 0.5 mM.Conclusion: These results suggest that zerovalent bismuth nanoparticles could be an interesting antimicrobial agent to be incorporated into an oral antiseptic preparation.Keywords: zerovalent bismuth nanoparticles, antimicrobial agent, biofilm, Streptococcus mutans

  10. Bismuth oxide aqueous colloidal nanoparticles inhibit Candida albicans growth and biofilm formation

    Directory of Open Access Journals (Sweden)

    Hernandez-Delgadillo R

    2013-04-01

    Full Text Available Rene Hernandez-Delgadillo,1 Donaji Velasco-Arias,3 Juan Jose Martinez-Sanmiguel,2 David Diaz,3 Inti Zumeta-Dube,3 Katiushka Arevalo-Niño,1 Claudio Cabral-Romero2 1Facultad de Ciencias Biológicas, Instituto de Biotecnologia, Universidad Autonoma de Nuevo Leon, UANL, Monterrey, Mexico; 2Facultad de Odontología, Universidad Autonoma de Nuevo Leon, UANL, Monterrey, México; 3Facultad de Quimica, Universidad Nacional Autonoma de Mexico, UNAM, Distrito Federal, México Abstract: Multiresistance among microorganisms to common antimicrobials has become one of the most significant concerns in modern medicine. Nanomaterials are a new alternative to successfully treat the multiresistant microorganisms. Nanostructured materials are used in many fields, including biological sciences and medicine. Recently, it was demonstrated that the bactericidal activity of zero-valent bismuth colloidal nanoparticles inhibited the growth of Streptococcus mutans; however the antimycotic potential of bismuth nanostructured derivatives has not yet been studied. The main objective of this investigation was to analyze the fungicidal activity of bismuth oxide nanoparticles against Candida albicans, and their antibiofilm capabilities. Our results showed that aqueous colloidal bismuth oxide nanoparticles displayed antimicrobial activity against C. albicans growth (reducing colony size by 85% and a complete inhibition of biofilm formation. These results are better than those obtained with chlorhexidine, nystatin, and terbinafine, the most effective oral antiseptic and commercial antifungal agents. In this work, we also compared the antimycotic activities of bulk bismuth oxide and bismuth nitrate, the precursor metallic salt. These results suggest that bismuth oxide colloidal nanoparticles could be a very interesting candidate as a fungicidal agent to be incorporated into an oral antiseptic. Additionally, we determined the minimum inhibitory concentration for the synthesized

  11. Sulfate-reducing bacteria slow intestinal transit in a bismuth-reversible fashion in mice.

    Science.gov (United States)

    Ritz, N L; Lin, D M; Wilson, M R; Barton, L L; Lin, H C

    2017-01-01

    Hydrogen sulfide (H 2 S) serves as a mammalian cell-derived gaseous neurotransmitter. The intestines are exposed to a second source of this gas by sulfate-reducing bacteria (SRB). Bismuth subsalicylate binds H 2 S rendering it insoluble. The aim of this study was to test the hypothesis that SRB may slow intestinal transit in a bismuth-reversible fashion. Eighty mice were randomized to five groups consisting of Live SRB, Killed SRB, SRB+Bismuth, Bismuth, and Saline. Desulfovibrio vulgaris, a common strain of SRB, was administered by gavage at the dose of 1.0 × 10 9 cells along with rhodamine, a fluorescent dye. Intestinal transit was measured 50 minutes after gavage by euthanizing the animals, removing the small intestine between the pyloric sphincter and the ileocecal valve and visualizing the distribution of rhodamine across the intestine using an imaging system (IVIS, Perkin-Elmer). Intestinal transit (n=50) was compared using geometric center (1=minimal movement, 100=maximal movement). H 2 S concentration (n=30) was also measured when small intestinal luminal content was allowed to generate this gas. The Live SRB group had slower intestinal transit as represented by a geometric center score of 40.2 ± 5.7 when compared to Saline: 73.6 ± 5.7, Killed SRB: 77.9 ± 6.9, SRB+Bismuth: 81.0 ± 2.0, and Bismuth: 73.3 ± 4.2 (Pfashion in mice. Our results demonstrate that intestinal transit is slowed by SRB and this effect could be abolished by H 2 S-binding bismuth. © 2016 John Wiley & Sons Ltd.

  12. Leaching of 210Po in human saliva from smokeless tobacco

    International Nuclear Information System (INIS)

    Syed, U.F.; Bari, A.; Husain, L.; Husain, L.

    2009-01-01

    Use of smokeless tobacco (SLT) is associated with cancer of the oral cavity. 210 Po, a known carcinogen present in SLT may leach into the saliva when the snuff is held in the mouth. Alpha emission from leached 210 Po can cause oral tissue damage, especially in the presence of non healing ulcers seen frequently in snuff users' mouth. Leaching of 210 Po from SLT in human saliva was determined for six popular US snuff brands. 210 Po was leached into human saliva for 30 min, separated radiochemically and its activity was determined by α-counting. Approximately 2-10% of 210 Po present in SLT was observed to leach. Annual exposure from leached 210 Po, based on average daily consumption of 15 g of SLT, was calculated to range from 1.1 to 3.8 Bq year -1 . (author)

  13. Dicty_cDB: SSF210 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available SS (Link to library) SSF210 (Link to dictyBase) - - - Contig-U16581-1 SSF210P (Link... to Original site) SSF210F 183 SSF210Z 197 SSF210P 380 - - Show SSF210 Library SS (Link to library) Clone ID SSF210 (Link to dict...yBase) Atlas ID - NBRP ID - dictyBase ID - Link to Contig Contig-U16581-1 Original site URL http://dict...nt alignments: (bits) Value N D16417 |D16417.1 Dictyostelium discoideum mRNA. 339...01670 Skin cDNA library Ictalurus punctatus cDNA 5' similar to Ictacalcin, mRNA s

  14. Determination of the mean aerosol residence times in the atmosphere and additional 210Po input on the base of simultaneous determination of 7Be, 22Na, 210Pb, 210Bi and 210Po in urban air

    International Nuclear Information System (INIS)

    Magdalena Dlugosz-Lisiecka; Henryk Bem

    2012-01-01

    The significant differences in the activities of 210 Pb, 210 Bi, 210 Po and cosmogenic 7 Be and 22 Na radionuclides in the urban aerosol samples collected in the summers 2010 and 2011 in the Lodz city of Poland were observed. Simultaneous measurement of these radionuclides, after a simple modification of the one compartment model, allows us to calculate both: the corrected aerosol residence times in the troposphere (1 / 25 days) and in the lower stratosphere (103 / 205 days). The relative input of the additional sources (beside of the 222 Rn decay in the air) to the total activity concentrations of 210 Pb, 210 Bi and 210 Po radionuclides in the urban air, plays a substantial role (up to 97% of the total activity) only in the case of 210 Po. (author)

  15. Spectroscopic Characterization of Extracellular Polymeric Substances from Escherichia coli and Serratia marcescens: Suppression using Sub-Inhibitory Concentrations of Bismuth Thiols

    Energy Technology Data Exchange (ETDEWEB)

    Badireddy, Appala R.; Korpol, Bhoom Reddy; Chellam, Shankararaman; Gassman, Paul L.; Engelhard, Mark H.; Lea, Alan S.; Rosso, Kevin M.

    2008-10-21

    Free and capsular EPS produced by Escherichia coli and Serratia marcescens were characterized in detail using Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and Auger electron spectroscopy (AES). Total EPS production decreased upon treatment with sub-inhibitory concentrations of lipophilic bismuth thiols (bismuth dimercaptopropanol, BisBAL; bismuth ethanedithiol, BisEDT; and bismuth pyrithione, BisPYR), BisBAL being most effective. Bismuth thiols also influenced acetylation and carboxylation of polysaccharides in EPS from S. marcescens. Extensive homology between EPS samples in the presence and absence of bismuth was observed with proteins, polysaccharides, and nucleic acids varying predominantly only in the total amount expressed. Second derivative analysis of the amide I region of FTIR spectra revealed decreases in protein secondary structures in the presence of bismuth thiols. Hence, anti-fouling properties of bismuth thiols appear to originate in their ability to suppress O-acetylation and protein secondary structures in addition to total EPS secretion.

  16. 137Cs and 210Po in Pacific Walrus and Bearded Seal from St. Lawrence Island, Alaska

    International Nuclear Information System (INIS)

    Hamilton, T F; Seagars, D J; Jokela, T; Layton, D

    2005-01-01

    The activity concentration of Cesium-137 ( 137 Cs) and naturally-occurring Polonium-210 ( 210 Po) were measured in the muscle tissue, kidney and liver of Pacific walrus (Odobenus rosmarus divergens) and bearded seal (Erignathus barbatus) collected by native hunters from the Bering Sea. The mean 137 Cs concentrations in muscle, liver and kidney of Pacific walrus were 0.07, 0.09 and 0.07 Bq kg -1 (N= 5, wet weight), respectively, and 0.17, 0.10, and 0.17 Bq kg -1 (N=2, wet weight), respectively, in bearded seal. In general, 137 Cs tissue concentrations are significantly lower than those previously reported for mammals from other regions. By comparison, 210 Po activity concentrations appear to be higher than those reported elsewhere but a larger variation. The mean 210 Po concentration in the muscle tissue, liver and kidney of Pacific walrus (N=5, wet weight) were 28.7, 189, and 174 Bq kg -1 , respectively. This compares with 210 Po concentration values (N=2, wet weight) of 27, 207, and 68 Bq kg -1 measured in the muscle tissue, liver and kidney, of bearded seal, respectively. Estimated bioaccumulation factors--as defined by the radionuclide concentration ratio between the target tissue to that in sea water--were two to three orders of magnitude higher for 210 Po that those of 137 Cs. We conclude from radiological dose estimates that ingestion of 137 Cs in foods derived from walrus and seal will pose no threat to human health. This work has important implications for assessing health risks to Alaskan coastal communities concerned about the dumping of nuclear waste in the Russia Arctic

  17. 137Cs and 210Po in Pacific walrus and bearded seal from St. Lawrence Island, Alaska

    International Nuclear Information System (INIS)

    Hamilton, Terry; Seagars, Dana; Jokela, Terry; Layton, David

    2008-01-01

    The activity concentration of Cesium-137 ( 137 Cs) and naturally-occurring Polonium-210 ( 210 Po) were measured in the muscle tissue, kidney and liver of Pacific walrus (Odobenus rosmarus divergens) and bearded seal (Erignathus barbatus) collected by native hunters from the Bering Sea during May 1996. The mean 137 Cs concentrations in muscle, liver and kidney of Pacific walrus were 0.07, 0.09 and 0.07 Bq kg -1 (n = 5, wet weight), respectively, and 0.17, 0.10, and 0.17 Bq kg -1 (n = 2, wet weight), respectively, in bearded seal. In general, 137 Cs tissue concentrations are significantly lower than those previously reported for mammals from other regions. By comparison, 210 Po activity concentrations are more variable and appear to be higher level compared with mammal data from other regions. The mean 210 Po concentration in the muscle tissue, liver and kidney of Pacific walrus (n = 5, wet weight) were 28.7, 189, and 174 Bq kg -1 , respectively. This compares with 210 Po concentration values (n = 2, wet weight) of 27, 207 and 68 Bq kg -1 measured in the muscle tissue, liver and kidney, of bearded seal, respectively. Estimated concentration factors-as defined by the radionuclide concentration ratio between the target tissue to that in sea water-were two to three orders of magnitude higher for 210 Po that those of 137 Cs. We conclude from radiological dose estimates that ingestion of 137 Cs in foods derived from walrus and seal will pose no threat to human health. This work has important implications for assessment of risks of Alaskan coastal communities concerned about the dumping of nuclear waste in the Russia Arctic

  18. 137Cs and 210Po in Pacific walrus and bearded seal from St. Lawrence Island, Alaska.

    Science.gov (United States)

    Hamilton, Terry; Seagars, Dana; Jokela, Terry; Layton, David

    2008-06-01

    The activity concentration of Cesium-137 ((137)Cs) and naturally-occurring Polonium-210 ((210)Po) were measured in the muscle tissue, kidney and liver of Pacific walrus (Odobenus rosmarus divergens) and bearded seal (Erignathus barbatus) collected by native hunters from the Bering Sea during May 1996. The mean (137)Cs concentrations in muscle, liver and kidney of Pacific walrus were 0.07, 0.09 and 0.07 Bq kg(-1) (n=5, wet weight), respectively, and 0.17, 0.10, and 0.17 Bq kg(-1) (n=2, wet weight), respectively, in bearded seal. In general, (137)Cs tissue concentrations are significantly lower than those previously reported for mammals from other regions. By comparison, (210)Po activity concentrations are more variable and appear to be higher level compared with mammal data from other regions. The mean (210)Po concentration in the muscle tissue, liver and kidney of Pacific walrus (n=5, wet weight) were 28.7, 189, and 174 Bq kg(-1), respectively. This compares with (210)Po concentration values (n=2, wet weight) of 27, 207 and 68 Bq kg(-1) measured in the muscle tissue, liver and kidney, of bearded seal, respectively. Estimated concentration factors--as defined by the radionuclide concentration ratio between the target tissue to that in sea water--were two to three orders of magnitude higher for (210)Po that those of (137)Cs. We conclude from radiological dose estimates that ingestion of (137)Cs in foods derived from walrus and seal will pose no threat to human health. This work has important implications for assessment of risks of Alaskan coastal communities concerned about the dumping of nuclear waste in the Russia Arctic.

  19. {sup 210}Pb and {sup 210}Po as tracers of particle transport mechanisms on continental margins

    Energy Technology Data Exchange (ETDEWEB)

    Radakovitch, O.; Heussner, S. [Perpignan Univ., 66 (France). Lab. de Sedimentologie et Geochimie Marines; Biscaye, P.; Abassi, A. [Columbia Univ., Palisades, NY (United States). Lamont Doherty Earth Observatory

    1997-12-31

    The natural radionuclides {sup 210}Po and {sup 210}Pb, members of the {sup 238}U decay chain, are particularly helpful to the understanding of particle transport processes in the ocean. These isotopes were analysed on sediment trap particles collected during 3 one-year experiments on continental margins. In the Bay of Biscay (Northeastern Atlantic) and in the Gulf of Lion (Northwestern Mediterranean Sea) both as part of the French ECOMARGE programme, and in the Middle Atlantic Bight (Northwestern Atlantic) as part of the SEEP programme. They yielded great insights into scenarios of particle transfer at each site, mainly based on the spatial and temporal distribution of {sup 210}Pb particulate concentrations and fluxes. (author) 11 refs.

  20. Radiation poisoning with Po-210 in London: The medical implications

    International Nuclear Information System (INIS)

    Perkins, A.C.

    2007-01-01

    Full text: The death of Alexander Litvinenko on 23 November 2006 has elevated the prospect of a deliberate radiation poisoning from a theoretical possibility to a reality. This was an unprecedented event in the UK. Poison that was certainly not the work of an amateur assassin was found, and it is possible that there have been previous killings of this nature outside the UK. Po-210 is a highly toxic radioactive heavy metal with a half-life of 138 days that decays, giving off 5.3MeV alpha particles having a range of 40-50mm in tissue. The poison was probably administered in a small volume of liquid or as a solid powder added to food or drink. Dispersal of the material resulted in widespread contamination that was detected across London and on British Airways' flights to the east. Following the event, the main task of the UK Health Protection Agency was of contamination monitoring and reassurance of the general public. With many researchers now investigating the use of targeted alpha therapy, this incident has highlighted the possible effects from the uptake of alpha emitters into the sensitive normal tissues. On reaching the bloodstream, Po- 210 is rapidly deposited in major organs and tissues including the liver, kidneys and bone marrow. The intense alpha radiation within these tissues would result in massive destruction of cells, leading to a rapid decline in health. It has been concluded that ingestion of 1-3 GBq or greater of Po-210 is likely to result in death within a few weeks, assuming there is 10% absorption to blood. Anyone receiving such doses would show symptoms of acute radiation sickness syndrome, with death resulting from multiple organ failure. Remedial medical treatment strategies would be unsuccessful within a few hours of ingestion, once significant amounts of Po-210 had entered the blood stream and deposited in tissues. The surreptitious nature of this act almost escaped detection. The fact that the nature of the poison was not known until the