WorldWideScience

Sample records for biscyanate ester resin

  1. Application conditions for ester cured alkaline phenolic resin sand

    Directory of Open Access Journals (Sweden)

    Ren-he Huang

    2016-07-01

    Full Text Available Five organic esters with different curing speeds: propylene carbonate (i.e. high-speed ester A; 1, 4-butyrolactone; glycerol triacetate (i.e. medium-speed ester B; glycerol diacetate; dibasic ester (DBE (i.e. low-speed ester C, were chosen to react with alkaline phenolic resin to analyze the application conditions of ester cured alkaline phenolic resin. The relationships between the curing performances of the resin (including pH value, gel pH value, gel time of resin solution, heat release rate of the curing reaction and tensile strength of the resin sand and the amount of added organic ester and curing temperature were investigated. The results indicated the following: (1 The optimal added amount of organic ester should be 25wt.%-30wt.% of alkaline phenolic resin and it must be above 20wt.%-50 wt.% of the organic ester hydrolysis amount. (2 High-speed ester A (propylene carbonate has a higher curing speed than 1, 4-butyrolactone, and they were both used as high-speed esters. Glycerol diacetate is not a high-speed ester in alkaline phenolic resin although it was used as a high-speed ester in ester cured sodium silicate sand; glycerol diacetate and glycerol triacetate can be used as medium-speed esters in alkaline phenolic resin. (3 High-speed ester A, medium-speed ester B (glycerol triacetate and low-speed ester C (dibasic ester, i.e., DBE should be used below 15 ìC, 35 ìC and 50 ìC, respectively. High-speed ester A or low-speed ester C should not be used alone but mixed with medium-speed ester B to improve the strength of the resin sand. (4 There should be a suitable solid content (generally 45wt.%-65wt.% of resin, alkali content (generally 10wt.%-15wt.% of resin and viscosity of alkaline phenolic resin (generally 50-300 mPa≤s in the preparation of alkaline phenolic resin. Finally, the technique conditions of alkaline phenolic resin preparation and the application principles of organic ester were discussed.

  2. Emission and Mechanical Evaluations of Vinyl-Ester Resin Systems

    National Research Council Canada - National Science Library

    Sands, James

    2003-01-01

    Vinyl-ester resins (VE) are frequently used in liquid molding of composite materials for several applications including naval and army structures, commercial boat manufacturing, and building construction...

  3. Characterization and Process Development of Cyanate Ester Resin and Composite

    Energy Technology Data Exchange (ETDEWEB)

    Frame, B.J.

    1998-03-01

    Cyanate ester (or polycyanate) resins offer advantages as composite matrices because of their high thermal stability, low outgassing, low water absorption and radiation resistance. This report describes the results of a processing study to develop high-strength hoop-wound composite by the wet-filament winding method using Toray T1000G carbon fiber and YLA RS-14A polycyanate resin as the constituent materials. Process trials, tests and analyses were conducted in order to gain insight into factors that can affect final properties of the cured cyanate ester resin and its composites. The study shows that the cyanate ester resin has a broad process envelope but that an inert-atmosphere cure is essential for obtaining optimum resin and composite properties. Minimizing moisture exposure prior to cure is also crucial as it affects the T{sub g} of the resin and composite. Recommendations for reducing moisture contact with the resin during wet-winding are presented. High fiber volume fraction ({approximately}80%) composites wound and cured with these methods yielded excellent hoop tensile strengths (660 to 670 ksi average with individual rings failing above 700 ksi), which are believed to be the highest recorded strengths for this class of materials. The measured transverse properties were also exceptional for these high fiber fraction composites. Based on the available data, this cyanate ester resin system and its composites are recommended for space and vacuum applications only. Further testing is required before these materials can be recommended for long term use at elevated temperatures in an ambient air environment. The results of all analyses and tests performed as part of this study are presented as well as baseline process for fabricating thick, stage-cured composites. The manufacture of a 1 in. thick composite cylinder made with this process is also described.

  4. New phenolic esters from the resinous exudate of Haplopappus taeda.

    Science.gov (United States)

    Faini, Francesca; Labbé, Cecilia; Torres, René; Rodilla, Jesús M; Silva, Lucía; Delle Monache, Franco

    2007-12-01

    Two new phenolic esters 9-trans-p-coumaroyloxy-alpha-terpineol (1) and 7-trans-p-coumaroyloxy-taedol (2), both endowed with free radical scavenger activity and cleroda-3,13 (E)-dien-15,18-diol (3) for which a cis stereochemistry at the decalin junction was found, were isolated from the resinous exudate from Haplopappus taeda upper parts.

  5. Curing reaction of bisphenol-A based benzoxazine with cyanate ester resin and the properties of the cured thermosetting resin

    Directory of Open Access Journals (Sweden)

    H. Kimura

    2011-12-01

    Full Text Available Curing reaction of bisphenol-A based benzoxazine with cyanate ester resin and the properties of the cured thermosetting resin were investigated. The cure behavior of benzoxazine with cyanate ester resin was monitored by model reaction using nuclear magnetic resonance (NMR. As a result of the model reaction, the ring opening reaction of benzoxazine ring and thermal self-cyclotrimerization of cyanate ester group occurred, and then the phenolic hydoroxyl group generated by the ring opening reaction of benzoxazine ring co-reacted with cyanate ester group. The properties of the cured thermosetting resin were estimated by mechanical properties, electrical resistivity, water resistance and heat resistance. The cured thermosetting resin from benzoxazine and cyanate ester resin showed good heat resistance, high electrical resistivity and high water resistance, compared with the cured thermosetting resin from benzoxazine and epoxy resin.

  6. Environmentally Friendly Bio-Based Vinyl Ester Resins for Military Composite Structures

    Science.gov (United States)

    2008-12-01

    formulations have been developed. The FAVE-L resin uses 65% Bisphenol A vinyl ester monomer, 20 wt% styrene, and 15 wt% methacrylated lauric acid (MLau...composites, fatty acid , vinyl ester 9. Distribution $tatement (requr’iedl lsmanuscript subjectto export control? E ruo I yes Circfe appropriate l tter and...resins is to replace some or all of the styrene with fatty acid -based monomers. These fatty acid vinyl ester resins allow for the formulation of high

  7. Synthesis, properties and applications of interacting blends of acrylated novalac epoxy resin based poly(ester-amides and vinyl ester

    Directory of Open Access Journals (Sweden)

    Pragnesh N. Dave

    2016-09-01

    Full Text Available Epoxy resin based unsaturated poly(ester-amide resins (UPEAs were prepared by the reported method. These UPEAs were then treated with acryloyl chloride to afford acrylated UPEAs resin (i.e. AUPEAs. Interacting blends of equal proportional AUPEAs and vinyl ester epoxy (VE resin were prepared. APEAs and AUPEAs were characterized by elemental analysis, molecular weight determined by vapor pressure osmometer and by IR spectral study and by thermogravimetry. The curing of interacting blends was monitored on differential scanning calorimeter (DSC. Based on DSC data in situ glass reinforced composites of the resultant blends have been prepared and characterized for mechanical, electrical and chemical properties. Unreinforced blends were characterized by thermogravimetry (TGA.

  8. Predicting the Viscosity of Low VOC Vinyl Ester and Fatty Acid-Based Resins

    National Research Council Canada - National Science Library

    LaScala, John J; Jeyarajasingam, Amutha; Winston, Cherise; Sand, James M; Palmese, Guiseppe R

    2005-01-01

    .... The viscosities of these resins were measured as a function of reactive diluent content and type, temperature, and vinyl ester molecular weight to determine the operating window for composite manufacture...

  9. Industrial alkyd resins: characterization of pentaerythritol and phthalic acid esters using integrated mass spectrometry.

    Science.gov (United States)

    La Nasa, Jacopo; Degano, Ilaria; Modugno, Francesca; Colombini, Maria Perla

    2015-02-15

    Alkyd resins are synthetic polyesters used as paints and coatings. Current approaches for their analysis do not allow the characterization of pentaerythritol and phthalic acid esters, whose detection is interesting to fully characterize the materials, e.g. for forensic or cultural heritage applications. A combined analytical approach based on Gas Chromatography/Mass Spectrometry (GC/MS), High-Performance Liquid Chromatography (HPLC)/MS and flow injection analysis (FIA)/MS was adopted. GC/MS was used to characterize the fatty acid profile and the polybasic acids in extracts from industrial alkyd resins. HPLC/MS and FIA/MS were used for the characterization of the triglyceride profile of the oil used to manufacture the resin and for the identification of reaction products deriving from the synthesis process. The multi-analytical approach was applied on two different industrial alkyd resins produced from two different oils. The GC/MS analysis was successful in characterizing the fatty acid profile and the aromatic fraction of the resin. The HPLC/MS analysis allowed us to characterize the pentaerythritol and phthalic acid ester and the triglycerides residues from the synthesis process, by studying their high-resolution tandem mass spectra. The application of liquid chromatography coupled with high-resolution tandem mass spectrometry to the study of industrial alkyd resins allowed us to characterize for the first time the esters formed by the transesterification reactions involving pentaerythritol, phthalic acid and triglycerides. Copyright © 2014 John Wiley & Sons, Ltd.

  10. Graphene Oxide and Thermally Exfoliated Graphene Cyanate Ester Resin Composites

    Science.gov (United States)

    2013-05-01

    arranged in a honey -comb lattice, its high surface to volume ratio allows property improvements at lower weight fractions than other composite fillers...Resin Composites 5a. CONTRACT NUMBER In-House 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Josiah T. Reams, Kevin R. Lamison...materials for space and propulsion applications have brought attention to the need for high temperature composite materials with improved stiffness

  11. Evaluation of bisphenol E cyanate ester for the resin-injection repair of advanced composites

    Energy Technology Data Exchange (ETDEWEB)

    Lio, Wilber Yaote [Iowa State Univ., Ames, IA (United States)

    2009-12-01

    This thesis is a compilation of a general introduction and literature review that ties together the subsequent chapters which consist of two journal articles that have yet to be submitted for publication. The overall topic relates to the evaluation and application of a new class of cyanate ester resin with unique properties that lend it applicable to use as a resin for injection repair of high glass transition temperature polymer matrix composites. The first article (Chapter 2) details the evaluation and optimization of adhesive properties of this cyanate ester and alumina nanocomposites under different conditions. The second article (Chapter 3) describes the development and evaluation of an injection repair system for repairing delaminations in polymer matrix composites.

  12. Usage of methyl ester of tall oil fatty acids and resinic acids as alternative diesel fuel

    International Nuclear Information System (INIS)

    Keskin, Ali; Yasar, Abdulkadir; Guerue, Metin; Altiparmak, Duran

    2010-01-01

    In the experimental study, tall oil fatty and resinic acids were investigated as alternative diesel fuels. The fatty acids, obtained by distilling the crude tall oil, were esterified with methanol in order to obtain tall oil methyl ester (biodiesel). Blends of the methyl ester, resinic acids and diesel fuel were prepared for test fuels. Performance and emission tests of the test fuels were carried out in an unmodified direct injection diesel engine on full load conditions. The results showed that the specific fuel consumption (SFC) with the blend fuels did not show a significant change. CO emission and smoke level decreased up to 23.91% and 19.40%, respectively. In general, NO x emissions showed on trend of increasing with the blend fuels (up to 25.42%). CO 2 emissions did not vary with the blend fuels significantly.

  13. Usage of methyl ester of tall oil fatty acids and resinic acids as alternative diesel fuel

    Energy Technology Data Exchange (ETDEWEB)

    Keskin, Ali; Yasar, Abdulkadir [Tarsus Technical Education Faculty, Mersin University, 33500 Mersin (Turkey); Guerue, Metin [Engineering and Architectural Faculty, Gazi University, 06570 Maltepe, Ankara (Turkey); Altiparmak, Duran [Technical Education Faculty, Gazi University, 06500 Ankara (Turkey)

    2010-12-15

    In the experimental study, tall oil fatty and resinic acids were investigated as alternative diesel fuels. The fatty acids, obtained by distilling the crude tall oil, were esterified with methanol in order to obtain tall oil methyl ester (biodiesel). Blends of the methyl ester, resinic acids and diesel fuel were prepared for test fuels. Performance and emission tests of the test fuels were carried out in an unmodified direct injection diesel engine on full load conditions. The results showed that the specific fuel consumption (SFC) with the blend fuels did not show a significant change. CO emission and smoke level decreased up to 23.91% and 19.40%, respectively. In general, NO{sub x} emissions showed on trend of increasing with the blend fuels (up to 25.42%). CO{sub 2} emissions did not vary with the blend fuels significantly. (author)

  14. A positron annihilation study on the microstructure of the interpenetration polymer networks of cyanate ester resin/epoxy resin

    International Nuclear Information System (INIS)

    Qi Chenze; Li Chunqing; Zeng Minfeng; Zhang Jian; Wang Baoyi

    2010-01-01

    Cyanate ester (CE) resin was blended with epoxy resin (EP) at different mass ratios (CE/EP: 100/0, 90/10, 70/30, 50/50, 30/70, 10/90, 0/100). The free volume size of CE/EP IPNs has been determined by positron annihilation lifetime spectroscopy (PALS). The size decreased as the epoxy resin content increased. The PALS results are consistent with the chemical structure changes for the copolymerizing between CE and EP. The crosslinking units of curing products (oxazoline, oxazolidinone, and polyether network) of the blends are all smaller in size than those of triazine ring structure from neat CE. Therefore, the free volume size of the blends decreases with increase of EP content. Examination of the mechanical properties, thermal stability, and morphology of the blend systems showed that addition of epoxy resin resulted in improved toughness but a little sacrifice in thermal stability when compared with pure CE. The correlations between the free volume properties and physical properties (thermal stability and mechanical properties) have been discussed.

  15. The effects of water absorption on an ester vinyl resin system

    Directory of Open Access Journals (Sweden)

    Ledjane Lima Sobrinho

    2009-09-01

    Full Text Available Derakene is a vinyl ester resin largely employed as matrix for polymeric based composite systems. In this work, the performance of such polymeric system was evaluated considering the effect of hygrothermal aging. The mechanical and thermal properties were examined for the processed material before and after ageing in water at 60 ºC for a maximum period of 64 days. Both analyses indicated the occurrence of post cure of the system after 16 days due to exposition at 60 ºC in water, which was also confirmed by analyses in samples with post cure treatment. Moreover, it was observed plasticizing of resin after 36 and 64 days of ageing. Micro structural and fracture surface analyses were carried out in order to characterize the samples. The appearance of surface voids was also observed.

  16. Tailoring the toughness and CTE of high temperature bisphenol E cyanate ester (BECy resin

    Directory of Open Access Journals (Sweden)

    M. Thunga

    2014-05-01

    Full Text Available The objective of the present work is to enhancing the toughness and minimizing the CTE of a special class of bisphenol E cyanate ester (BECy resin by blending it with a thermoplastic toughening agent. Poly(ether sulfone was chosen as a high temperature resistant thermoplastic resin to enhance the thermo-mechanical properties of BECy. The influence of poly(ether sulfone/BECy blend composition on the morphology and phase behavior was studied using scanning electron microscopy and dynamic mechanical analysis. The mechanical properties of the blends were evaluated by flexural tests, which demonstrated significant enhancement in the material’s toughness with an increase in PES concentration from 0 to 15 wt%. The coefficient of thermal expansion of pure BECy was reduced from 61 to 48 ppm/°C in the blends with PES, emphasizing the multi-functional benefits of PES as a toughening agent in BECy.

  17. Effects of gamma irradiation on the mechanical and thermal properties of cyanate ester/benzoxazine resin

    Science.gov (United States)

    Zegaoui, Abdeldjalil; Wang, An-ran; Qadeer Dayo, Abdul; Tian, Bo; Liu, Wen-bin; Wang, Jun; Liu, Yu-guang

    2017-12-01

    In this study, thermosetting resin blends composed of cyanate ester (CE) and benzoxazine (BOZ) were prepared and then subjected to gamma-ray irradiation with doses up to 1000 kGy from a cobalt-60 gamma irradiator. The objective of this present study was to experimentally assess the effect of γ-ray irradiation on the mechanical behaviour, chemical structure and thermal properties of the CE/BOZ resin blends by the bending test, dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), Fourier Transform Infrared (FTIR) and thermogravimetric analysis (TGA). The results showed that at a low radiation dose (250 kGy), the flexural strength and modulus, thermal stability, storage modulus and glass transition temperature of the CE/BOZ resin gradually declined first, then sharply increased when the radiation dose increased to 500 kGy and finally slightly dropped at the end with a dose of 1000 kGy. The decrease in the aforementioned properties could be ascribed to the degradation process including the rupture of chemical bonds and scission of molecular chains of the CE/BOZ resin blends, which were confirmed by the FTIR and SEM. However, a significant improvement in the thermal and mechanical properties of the blend was found when the radiation dose increased to 500 kGy.

  18. Development of solvent-free offset ink using vegetable oil esters and high molecular-weight resin.

    Science.gov (United States)

    Park, Jung Min; Kim, Young Han; Kim, Sung Bin

    2013-01-01

    In the development of solvent-free offset ink, the roles of resin molecular weight and used solvent on the ink performance were evaluated by examining the relationship between the various properties of resin and solvent and print quality. To find the best performing resin, the soy-oil fatty acid methyl ester (FAME) was applied to the five modified-phenolic resins having different molecular weights. It is found from the experimental results that the ink made of higher molecular weight and better solubility resin gives better printability and print quality. It is because larger molecular weight resin with better solubility gives higher rate of ink transfer. From the ink application of different esters to high molecular weight resin, the best printing performance was yielded from the soy-oil fatty acid butyl ester (FABE). It is due to its high kinematic viscosity resulting in the smallest change of ink transfer weight upon multiple number of printing, which improves the stability of ink quality.

  19. Thermal curing behavior of MWCNT modified vinyl ester-Polyester resin suspensions prepared with 3-roll milling technique

    OpenAIRE

    Seyhan, Abdullah Tuğrul; De La Vega, Alejandra; Tanoğlu, Metin; Schulte, Karl

    2009-01-01

    This study aims to investigate the curing behavior of a vinyl ester-polyester resin suspensions containing 0.3 wt % of multiwalled carbon nanotubes with and without amine functional groups (MWCNTs and MWCNT-NH2). For this purpose, various analytical techniques, including Differential Scanning Calorimetry (DSC), Fourier infrared spectroscopy (FTIR), Raman Spectroscopy, and Thermo Gravimetric Analyzer (TGA) were conducted. The resin suspensions with carbon nanotubes (CNTs) were prepared via 3-r...

  20. Toward reliable morphology assessment of thermosets via physical etching: Vinyl ester resin as an example

    Directory of Open Access Journals (Sweden)

    J. Karger-Kocsis

    2013-05-01

    Full Text Available The morphology of peroxide-cured, styrene crosslinked, bisphenol A-based vinyl ester (VE resin was investigated by atomic force microscopy (AFM after ‘physical’ etching with different methods. Etching was achieved by laser ablation, atmospheric plasma treatment and argon ion bombardment. Parameters of the etching were varied to get AFM scans of high topography resolution. VE exhibited a nanoscaled nodular structure the formation of which was ascribed to complex intra- and intermolecular reactions during crosslinking. The microstructure resolved after all the above physical etching techniques was similar provided that optimized etching and suitable AFM scanning conditions were selected. Nevertheless, with respect to the ‘morphology visualization’ these methods follow the power ranking: argon bombardment > plasma treatment > laser ablation.

  1. Anti-flammable vinyl ester resin nano-composite with nano-titania

    Science.gov (United States)

    Das, Rajib

    Anti-flammable material is a common expectation for any industry and household applications to protect the material from fire accident. Polymer composites also play a significant role in preparing anti flammable materials. Vinyl ester resins (VERs) are thermosetting resins that have excellent mechanical and thermal properties of epoxy resins and Nanotitania is an inexpensive, nontoxic and biocompatible inorganic material. In this paper to investigate the flame retardency of polymer nanocomposites VER is used as polymer matrix and TiO2 is used as inorganic nanofiller.3-[2-(2-aminoethylamino) ethylamino]propyl-trimethoxysilane (TATMS), a kind of silane is used as a coupling agent to functionalize the surface of nanoTiO2 to improve its flame retardency by adding Si and N2 group. TGA test and FTIR test have been performed and different peaks for Si and N2 in the modified nanofiller and weight loss of fabricated nanofiller confirmed that fabrication method was successful. After that, nanocomposite sample of VERs reinforced with nano TiO2 prepared and the effects of different loadings on mechanical and flame retardant properties are investigated after and before the modification of nanofillers. From tensile test result it is found that up to 5% loading of modified nanofiller the tensile strength is 62 MPa that is almost as same as pure VER and the tensile strength of unmodified nanofiller based PNC is 68 MPa which is not significant improvement in its mechanical property. From MCC test of flame retardancy it is found that the normalized heat release capacity of modified nanofiller based nanocomposite is decreased by 27.7% than unmodified nanofiller based PNC that is 9.8%. Also the normalized total heat release of modified nanofiller based PNC is 21.4% than unmodified PNC that is 12.4%.

  2. Morphological, Mechanical and Physio-chemical Performance of ortho-Cresol Epoxy Novolac Based Vinyl Ester Resin

    Directory of Open Access Journals (Sweden)

    Jaswal Shipra

    2015-09-01

    Full Text Available Vinyl ester resin (VEOCN was prepared from o-cresol epoxy resin (EOCN and methacrylic acid in the presence of triphenyl phosphine as catalyst and hydroquinone as inhibitor with acid value of ~ 7 mg of KOH per gram of solid. O-cresol based novolac resin (OCN, OCN based epoxy resin (EOCN and VEOCN were characterized by Fourier transform infra red spectroscopy (FT-IR, 1H-NMR and 13C-NMR. The thermal and mechanical behavior of the samples prepared at 30°C from VEOCN using styrene and methyl-methacrylate respectively as reactive diluents, in the presence of benzoyl peroxide (2 phr as initiator was studied using Differential Scanning Calorimetry (DSC, Thermogravimetric analysis (TGA and Universal Testing Machine (UTM. Chemical resistance of above VER samples was also evaluated as a function of % weight loss and with the help of Scanning Electron Microscopy (SEM, upon immersing the VEOCN samples in different solutions for 90 days.

  3. Laminates based on vinyl ester resin and glass fabric: A study on the thermal, mechanical and morphological characteristics

    International Nuclear Information System (INIS)

    Sultania, Minakshi; Yadaw, S.B.; Rai, J.S.P.; Srivastava, Deepak

    2010-01-01

    The effects of variation of styrene content on the thermal, mechanical and morphological behaviours of epoxy novolac vinyl ester resin (EVER)/glass fabric laminate have been investigated. The vinyl ester resin matrix was synthesized indigenously using epoxy novolac resin and methacrylic acid catalyzed by triphenylphosphine at a temperature of 85 deg. C in nitrogen atmosphere. Fourier-transform infra-red spectroscopic (FT-IR) analysis was used to see the structural changes during the synthesis of the EVER. Differential scanning calorimetric (DSC) technique was used to investigate the curing behaviour of the EVER matrix. Exothermic peaks (T p ) appeared in the range of 117-127 deg. C for all the samples of epoxy resin and EVERs. Thermal stability of the prepared samples was analyzed by dynamic thermogravimetric runs. The TG/DTG trace of epoxy showed two-step mass loss decomposition behaviour whereas that of vinyl ester resin exhibited a single step mass loss. Mechanical properties such as tensile, flexural and impact strengths of the prepared laminates were determined and it was found cured resin containing 40% styrene showed the best balance of properties and EVER/glass fabric laminates exhibited better properties as compared to the epoxy/glass fabric laminates Dynamic mechanical analyses of the samples were done to determine the viscoelastic properties. T g decreased significantly with increased styrene concentration due to increase in cross-linking density. Cross-sections of the cured samples, which failed during impact testing, have been critically studied through scanning electron microscopic (SEM) analysis to gain insight into the phase morphology.

  4. Synthetic resin-bound truncated Candida antarctica lipase B for production of fatty acid alkyl esters by transesterification of corn and soybean oils with ethanol or butanol.

    Science.gov (United States)

    Hughes, Stephen R; Moser, Bryan R; Robinson, Samantha; Cox, Elby J; Harmsen, Amanda J; Friesen, Jon A; Bischoff, Kenneth M; Jones, Marjorie A; Pinkelman, Rebecca; Bang, Sookie S; Tasaki, Ken; Doll, Kenneth M; Qureshi, Nasib; Liu, Siqing; Saha, Badal C; Jackson, John S; Cotta, Michael A; Rich, Joseph O; Caimi, Paolo

    2012-05-31

    A gene encoding a synthetic truncated Candida antarctica lipase B (CALB) was generated via automated PCR and expressed in Saccharomyces cerevisiae. Western blot analysis detected five truncated CALB variants, suggesting multiple translation starts from the six in-frame ATG codons. The longest open reading frame, which corresponds to amino acids 35-317 of the mature lipase, appeared to be expressed in the greatest amount. The truncated CALB was immobilized on Sepabeads® EC-EP resin and used to produce ethyl and butyl esters from crude corn oil and refined soybean oil. The yield of ethyl esters was 4-fold greater from corn oil than from soybean oil and was 36% and 50% higher, respectively, when compared to a commercially available lipase resin (Novozym 435) using the same substrates. A 5:1 (v/v) ratio of ethanol to corn oil produced 3.7-fold and 8.4-fold greater yields than ratios of 15:1 and 30:1, respectively. With corn oil, butyl ester production was 56% higher than ethyl ester production. Addition of an ionic catalytic resin step prior to the CALB resin increased yields of ethyl esters from corn oil by 53% compared to CALB resin followed by ionic resin. The results suggest resin-bound truncated CALB has potential application in biodiesel production using biocatalysts. Published by Elsevier B.V.

  5. Improvement of epoxy resin properties by incorporation of TiO2 nanoparticles surface modified with gallic acid esters

    International Nuclear Information System (INIS)

    Radoman, Tijana S.; Džunuzović, Jasna V.; Jeremić, Katarina B.; Grgur, Branimir N.; Miličević, Dejan S.; Popović, Ivanka G.; Džunuzović, Enis S.

    2014-01-01

    Highlights: • Nanocomposites of epoxy resin and TiO 2 nanoparticles surface modified with gallates. • The T g of epoxy resin was increased by incorporation of surface modified TiO 2 . • WVTR of epoxy resin decreased in the presence of surface modified TiO 2 nanoparticles. • WVTR of nanocomposites was reduced with increasing gallates hydrophobic chain length. • Modified TiO 2 nanoparticles react as oxygen scavengers, inhibiting steel corrosion. - Abstract: Epoxy resin/titanium dioxide (epoxy/TiO 2 ) nanocomposites were obtained by incorporation of TiO 2 nanoparticles surface modified with gallic acid esters in epoxy resin. TiO 2 nanoparticles were obtained by acid catalyzed hydrolysis of titanium isopropoxide and their structural characterization was performed by X-ray diffraction and transmission electron microscopy. Three gallic acid esters, having different hydrophobic part, were used for surface modification of the synthesized TiO 2 nanoparticles: propyl, hexyl and lauryl gallate. The gallate chemisorption onto surface of TiO 2 nanoparticles was confirmed by Fourier transform infrared and ultraviolet–visible spectroscopy, while the amount of surface-bonded gallates was determined using thermogravimetric analysis. The influence of the surface modified TiO 2 nanoparticles, as well as the length of hydrophobic part of the gallate used for surface modification of TiO 2 nanoparticles, on glass transition temperature, barrier, dielectric and anticorrosive properties of epoxy resin was investigated by differential scanning calorimetry, water vapor transmission test, dielectric spectroscopy, electrochemical impedance spectroscopy and polarization measurements. Incorporation of surface modified TiO 2 nanoparticles in epoxy resin caused increase of glass transition temperature and decrease of the water vapor permeability of epoxy resin. The water vapor transmission rate of epoxy/TiO 2 nanocomposites was reduced with increasing hydrophobic part chain length of

  6. Ester-free Thiol-X Resins: New Materials with Enhanced Mechanical Behavior and Solvent Resistance

    OpenAIRE

    Podgórski, Maciej; Becka, Eftalda; Chatani, Shunsuke; Claudino, Mauro; Bowman, Christopher N.

    2015-01-01

    A series of thiol-Michael and radical thiol-ene network polymers were successfully prepared from ester-free as well as ester-containing monomer formulations. Polymerization reaction rates, dynamic mechanical analysis, and solvent resistance experiments were performed and compared between compositions with varied ester loading. The incorporation of ester-free alkyl thiol, vinyl sulfone and allylic monomers significantly improved the mechanical properties when compared with commercial, mercapto...

  7. Thermo-mechanical correlations to erosion performance of short carbon fibre reinforced vinyl ester resin composites

    International Nuclear Information System (INIS)

    Kumar, Sandeep; Satapathy, Bhabani K.; Patnaik, Amar

    2011-01-01

    Research highlights: → Composite with 30 wt.% of short carbon fibres exhibit highest energy dissipation. → Optimum erosion resistance conditions have been found. → A direct correlation emerged between erosive wear rate and loss-modulus inverse. → Mechanistic equivalence between erosion and dynamic loading modes is established. -- Abstract: Thermo-mechanical properties and erosion performance of short carbon fibre reinforced vinyl ester resin based isotropic polymer composites with four different fibre weight fractions have been investigated. The storage, loss and damping characteristics were analysed to assess the energy absorption/viscous recoverable energy dissipation and reinforcement efficiency of the composites as a function of fibre content in the temperature range of 0-140 o C. The composite with 30 wt.% of short carbon fibres has been observed to exhibit superior thermo-mechanical response with highest energy dissipation/damping ability accompanied with a constant storage modulus without any substantial decay till 60 o C. The erosion rates (Er) of these composites are evaluated at different impingement angles (30-90 o ), fibre loadings (20-50 wt.%), impact velocities (43-76 m/s), stand-off distances (55-85 mm) and erodent sizes (250-600 μm) following the erosion test schedule in an air jet type test rig. An optimal parameter combination is determined and subsequently validated for erosion rate minimization following Taguchi method and by conducting confirmation experiments. A correlation between the loss-modulus inverse and the erosion rate has been observed which conceptually establishes a possible mechanistic equivalence between erosion and dynamic mechanical loading modes. The morphologies of eroded surface are examined by the scanning electron microscopy to investigate the nature of wear-craters, material damage mode and other qualitative attributes responsible for promoting erosion.

  8. Blending of Hydrocarbon and Rosin Ester-basedResins to Study its Effect on the Physical andMechanical Properties of Thermoplastic Road Markings

    Directory of Open Access Journals (Sweden)

    S.M. Mirabedini

    2009-12-01

    Full Text Available In this study, the effect of hydrocarbon and rosin ester resins combination on the physical and mechanical properties of thermoplastic road markings were evaluated. At first, two basic thermoplastic road marking formulations based on hydrocarbon and rosin ester resins were prepared. Several samples of the blends of two basic formulations for thermoplastic road marking were characterized and compared by their softening points, abrasion resistance, color data changes, DMTA and tensile strength values. The results showed that hydrocarbon-based thermoplastic road markings have better weathering resistance and rosin ester based materials illustrated enhanced heat resistance. The inclusion of rosin ester thermoplastic road marking into the hydrocarbon-based formulations, improves compatibility of the hydrocarbon resin and dibutyl phthalate (DBP(, as well as their physical and mechanical properties. The unique properties of rosin arise from its hydrophobic chain skeleton and its hydrophilic carboxy groups which contribute to its excellent solubility and compatibility with a variety of other synthetic resins. The best performance was obtained with 50 wt % inclusion of rosin ester to hydrocarbon based compound. DMTA analysis revelation with combination of hydrocarbon and rosin ester-based road markings showed that the decreasing trend in elastic modulus is shifted to higher temperature, and as a result it keeps the hardness and ductile properties of thermoplastic road markings unchanged. More favored raw materials for compatibilization of compounds in road marking formulations lead to higher elongation- at-break and an increased toughness.

  9. Ester-free Thiol-X Resins: New Materials with Enhanced Mechanical Behavior and Solvent Resistance.

    Science.gov (United States)

    Podgórski, Maciej; Becka, Eftalda; Chatani, Shunsuke; Claudino, Mauro; Bowman, Christopher N

    A series of thiol-Michael and radical thiol-ene network polymers were successfully prepared from ester-free as well as ester-containing monomer formulations. Polymerization reaction rates, dynamic mechanical analysis, and solvent resistance experiments were performed and compared between compositions with varied ester loading. The incorporation of ester-free alkyl thiol, vinyl sulfone and allylic monomers significantly improved the mechanical properties when compared with commercial, mercaptopropionate-based thiol-ene or thiol-Michael networks. For polymers with no hydrolytically degradable esters, glass transition temperatures (T g 's) as high as 100 °C were achieved. Importantly, solvent resistance tests demonstrated enhanced stability of ester-free formulations over PETMP-based polymers, especially in concentrated basic solutions. Kinetic analysis showed that glassy step-growth polymers are readily formed at ambient conditions with conversions reaching 80% and higher.

  10. Development and Characterization of Novel Interpenetrating Network (IPN Foams from Epoxy Ester and Aliphatic Epoxy Resin

    Directory of Open Access Journals (Sweden)

    Kanuprasad Patel

    2009-01-01

    Full Text Available Diglycidyl ether of bisphenol-A (DGEBA was reacted with acrylate monomer at variable molar ratios. The reaction between glycerine and epichlorohydrine form glycidyl ether of polyol aliphatic epoxy resin. The resultant resins were characterized duly. Both the resins were mixed at different ratios with constant high shear stirring. The obtained mixture and suitable additives were heated at 150oC for one and half hour. The so called Interpenetrating Network (IPN transformed into foams. The performance of foams was evaluated by testing for compression in both parallel and perpendicular to rise direction. The tests were carried out at room temperature and at the elevated temperature. The compression properties showed a decreasing trend for increasing amounts of glycerine resin. The density and thermal properties of epoxy foams were also evaluated. The relation between the composition, density and properties of the foam was analyzed.

  11. Preparation of carbon fiber unsaturated sizing agent for enhancing interfacial strength of carbon fiber/vinyl ester resin composite

    Science.gov (United States)

    Jiao, Weiwei; Cai, Yemeng; Liu, Wenbo; Yang, Fan; Jiang, Long; Jiao, Weicheng; Wang, Rongguo

    2018-05-01

    The practical application of carbon fiber (CF) reinforced vinyl ester resin (VE) composite was hampered seriously by the poor interfacial adhesion property. In this work, a novel unsaturated sizing agent was designed and prepared to improve the interfacial strength by covalently bonding CF with VE matrix. The main component of the sizing agent, N-(4‧4-diaminodiphenyl methane)-2-hydroxypropyl methacrylate (DMHM), was synthesized and confirmed by FTIR and NMR. XPS results of sized carbon fiber (SCF) showed that DMHM has adhered to desized fiber surface and reacted with some active functional groups on the surface. The SCF was characterized by high surface roughness and surface energy (especially the polar component), which means better wettability by VE. As a result, the interface shear strength and interlaminar shear strength of SCF/VE composite were enhanced by 96.56% and 66.07% respectively compared with CF/VE composite, benefited mainly from the strong and tough interphase.

  12. Bio-Based Cyanate Ester Resins: Improved Performance Through Network Structure Enhancement (Briefing Charts)

    Science.gov (United States)

    2014-03-17

    a Monomer Source 6 • Trans-anethole is widely available as an essential oil extracted from star anise ( Illicium verum ), an evergreen tree native to...and cyanate esters are similar Photograph of fruits of star anise (’’ Illicium verum ’’), taken 17th October 2006 by Brian Arthur and released under

  13. Structure/Property Relationships of Cyanate Ester Resins from Renewable Sources

    Science.gov (United States)

    2013-04-11

    with Near Zero Coefficient of Hygroscopic Expansion Δ Distribution A. Approved for public release; distribution is unlimited. Cyanate...distribution is unlimited. DSC of Creosol-Based Cyanate Esters 11 liquid at RT 120 kJ/mol Post-cure Tg: 153 °C (indicates degradation) m.p

  14. Cyanate Ester Resin Modified with Nano-particles for Inclusion in Continuous Fiber Reinforced Composites

    Science.gov (United States)

    2011-02-25

    transition. The impact strength of the fully cured specimens were determined using a Tinius Olsen Charpy impact strength tester. The samples were machined...by swinging the pendulum for 11 half cycles. 2.3 Results and Discussion The effect of CNT loading on the viscosity of BECy resin at 23 oC is

  15. Enhancing the quality of alkyd resins using methyl esters of rubber ...

    African Journals Online (AJOL)

    All the alkyd samples were fairly resistant to brine, acid and water but poorly resistant to alkali. However, the MERSO alkyds were observed to have a better resistance than the RSO alkyd resins. The scratch/gouge pencil hardness shows that the hardness of the alkyd films decreases with the oil length. Keywords: Alkyd ...

  16. The elastoplastic response of and moisture diffusion through a vinyl ester resin-clay nanocomposite

    DEFF Research Database (Denmark)

    Drozdov, Aleksey D.; Christiansen, Jesper de Claville; Gupta, R.K.

    2002-01-01

    Experimental data are reported on the elastoplastic response of and moisture diffusion through a vinyl ester resin–montmorillonite clay nanocomposite with various amounts of filler. Two simple models are developed for the elastoplastic behavior of a nanocomposite and for the anomalous diffusion...... of penetrant molecules. Adjustable parameters in the constitutive equations are found by fitting the observations. It is revealed that some critical concentration of filler exists (about 1 wt.-%): in the sub-critical region of concentrations, molecular mobility of the host polymer strongly decreases...

  17. Catalytic effect of carbon nanotubes on polymerization of cyanate ester resins

    Directory of Open Access Journals (Sweden)

    2009-08-01

    Full Text Available Kinetic peculiarities of polycyclotrimerization process of dicyanate ester of bisphenol A (DCBA in the presence of multi-walled carbon nanotubes (MWCNTs have been investigated using Fourier Transform Infrared Spectroscopy (FTIR spectroscopy technique. It has been found that even very small amounts of MWCNTs (0.01–0.1 wt% catalyze the reaction of polycyclotrimerization of DCBA leading to formation of polycyanurate network (PCN/MWCNTs nanocomposite. However, some decrease in final degree of conversion for nanocomposites compared to the neat PCN within the temperature/time schedule used was observed. The kinetic rate constants increased with addition of MWCNTs and energies of activation were found to be significantly decreased even at low contents of MWCNTs.

  18. Hybrid thermosets from vinyl ester resin and acrylated epoxidized soybean oil (AESO

    Directory of Open Access Journals (Sweden)

    2011-01-01

    Full Text Available A series of hybrids composed of styrene crosslinkable vinyl ester (VE and acrylated epoxidized soybean oil (AESO were produced via free radical-induced crosslinking. The VE/AESO ratio was changed between 75/25 and 25/75 wt%. Moreover, to support phase grafting the VE/AESO = 50/50 wt% hybrid was modified with phthalic anhydride in various amounts (1, 5 and 10 wt%. The structure of the hybrid systems was investigated by dynamic mechanical thermal analysis (DMTA, differential scanning calorimetry (DSC, and atomic force microscopy (AFM. The properties of the systems were assessed by static flexural and fracture mechanical tests. The resistance to thermal degradation was inspected by thermogravimetric analysis (TGA. The results suggested that the hybrids have an interpenetrating network (IPN structure. With increasing AESO content the stiffness (modulus, strength and glass transition temperature (Tg of the hybrids decreased, whereas their ductility increased. Phthalic anhydride caused an adverse trend. Both the fracture toughness and fracture energy increased with increasing AESO content. They were less affected by adding phthalic anhydride phase couplant. Interestingly, the hybrids outperformed the parent VE and AESO in respect to resistance to thermal degradation.

  19. Batatins I and II, ester-type dimers of acylated pentasaccharides from the resin glycosides of sweet potato.

    Science.gov (United States)

    Escalante-Sánchez, Edgar; Pereda-Miranda, Rogelio

    2007-06-01

    Batatins I (1) and II (2), two ester-type dimers of acylated pentasaccharides, have been isolated by recycling HPLC from the hexane-soluble extract of sweet potato (Ipomoea batatas var. batatas). The structures were elucidated by a combination of high-resolution NMR spectroscopy and mass spectrometry. Complete analysis and unambiguous assignments of the 1H and 13C NMR spectra of 1 and 2 were achieved by 2D shift correlation measurements. The glycosidic acid forming each branched pentasaccharide monomeric unit was confirmed as simonic acid B. Three different fatty acids esterify this core at the same positions in both batatins: C-2 on the second rhamnose unit and C-4 and C-2 (or C-3) on the third rhamnose moiety. The acylating residues were identified as (+)-(2S)-methylbutanoic, dodecanoic (lauric), and cinnamic acids. The site of lactonization by the aglycon in unit A was placed at C-3 of the second saccharide. The position for the ester linkage for monomeric unit B on the macrocylic unit A was identified as C-3 of the terminal rhamnose' ''. Through spectroscopic simulation of these complex oligosaccharides, the chemical shifts and coupling constants were deduced for the overlapped proton resonances with a non-first-order resolution. The experimental NMR spectroscopic values registered for batatinoside I (3), a new polyacylated macroyclic pentasaccharide also isolated from this plant, were used as the starting point for spectral simulation of 1 and 2. Both polymers 1 and 2 represent dimers of compound 3.

  20. Method of making a cyanate ester foam

    Science.gov (United States)

    Celina, Mathias C.; Giron, Nicholas Henry

    2014-08-05

    A cyanate ester resin mixture with at least one cyanate ester resin, an isocyanate foaming resin, other co-curatives such as polyol or epoxy compounds, a surfactant, and a catalyst/water can react to form a foaming resin that can be cured at a temperature greater than 50.degree. C. to form a cyanate ester foam. The cyanate ester foam can be heated to a temperature greater than 400.degree. C. in a non-oxidative atmosphere to provide a carbonaceous char foam.

  1. Allied, MGC link on cyanate esters

    International Nuclear Information System (INIS)

    Wood, A.

    1993-01-01

    In the latest of a line of joint ventures in its plastics business, Allied Signal has reached agreement with Mitsubishi Gas Chemical (MGC) to jointly develop thermoset cyanate ester resins and blends. The deal will involve further development of Allied Signal's Primaset phenol-formaldehyde cyanate ester resins, a new entrant in the thermoset arena. Although the Primaset resins were discovered in the 1960s, this would be the first time they are available commercially. The deal will marry Primaset technology with MGC's Skylex bisphenol A cyanate ester resins, says Fred DiAntonis, director/advanced materials at Allied Signal. The two firms are looking at marketing blends of the two materials. The potential market for these resins, used commercially by the electronics industry in printed circuit boards and by the aerospace industry in composites, is significant, says Robert P. Viarengo, Allied Signal president/performance materials. By aligning ourselves with MGC, the world leader in cyanate ester resin, we anticipate moving forward aggressively. The main competitor is Ciba, which acquired bisphenol A cyanate ester resins with its purchase of Rhone-Poulenc's high temperature resins business. DiAntonis estimates the market for cyanate ester resins could be worth $150 million by the end of the decade, although development costs have been in the tens of millions of dollars range

  2. Rice husk bio-oil upgrading by means of phase separation and the production of esters from the water phase, and novolac resins from the insoluble phase

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Junming; Jiang, Jianchun; Lv, Wei; Dai, Weidi; Sun, Yunjuan [Institute of Chemical Industry of Forest Products, CAF; National Engineering Lab, For Biomass Chemical Utilization; Key and Open Lab. on Forest Chemical Engineering, SFA, Nanjing 210042 (China)

    2010-07-15

    A new method of utilization of original bio-oil was developed in this paper. The procedure chosen was based on the fractionation of the bio-oils with water into water soluble and insoluble fractions. After oxidizing the aldehydes to acids by hydrogen peroxide, water soluble fraction was used to obtain upgraded bio-oil (light oil) with ethanol through reactive rectification. The yield of light oil was 20.6% (account to original bio-oil) and the components of upgraded bio-oil were characterized by HPLC and FT-IR. The analysis showed that the main components were ethyl acetate, ethyl formate, methyl acetate and methyl formate. Using water insoluble fractions as starting materials in synthesis of novolac resins was also studied. The water insoluble fraction was used as a substitute of phenol at different ratio to prepare novolac resins. Main properties of obtained resin such as cure time and soft point were characterized. The novolac property of resins was determined by DSC. (author)

  3. The fabrication of monolithic capillary column based on poly (bisphenol A epoxy vinyl ester resin-co-ethylene glycol dimethacrylate) and its applications for the separation of small molecules in high performance liquid chromatography.

    Science.gov (United States)

    Niu, Wenjing; Wang, Lijuan; Bai, Ligai; Yang, Gengliang

    2013-07-05

    A new polymeric monolith was synthesized in fused-silica capillary by in situ polymerization technique. In the polymerization, bisphenol A epoxy vinyl ester resin (VER) was used as the functional monomer, ethylene glycol dimethacrylate (EDMA) as the crosslinking monomer, 1,4-butanediol, 1-propanol and water as the co-porogens, and azobisisobutyronitrile (AIBN) as the initiator. The conditions of polymerization have been optimized. Morphology of the prepared poly (VER-co-EDMA) monolith was investigated by the scanning electron microscopy (SEM); pore properties were assayed by mercury porosimetry and nitrogen adsorption. The optimized poly (VER-co-EDMA) monolith showed a uniform structure, good permeability and mechanical stability. Then, the column was used as the stationary phase of high performance liquid chromatography (HPLC) to separate the mixture of benzene derivatives. The best column efficiency achieved for phenol was 235790 theoretical plates per meter. Baseline separations of benzene derivatives and halogenated benzene compounds under optimized isocratic mode conditions were achieved with high column efficiency. The column showed good reproducibility: the relative standard deviation (RSD) values based on the retention times (n=3) for run-to-run, column-to-column and batch-to-batch were less than 0.98, 1.68, 5.48%, respectively. Compared with poly (BMA-co-EDMA) monolithic column, the proposed monolith exhibited more efficiency in the separation of small molecules. Copyright © 2013 Elsevier B.V. All rights reserved.

  4. Synthesis of improved phenolic and polyester resins

    Science.gov (United States)

    Delano, C. B.

    1980-01-01

    Thirty-seven cured phenolic resin compositions were prepared and tested for their ability to provide improved char residues and moisture resistance over state of the art epoxy resin composite matrices. Cyanate, epoxy novolac and vinyl ester resins were investigated. Char promoter additives were found to increase the anaerobic char yield at 800 C of epoxy novolacs and vinyl esters. Moisture resistant cyanate and vinyl ester compositions were investigated as composite matrices with Thornel 300 graphite fiber. A cyanate composite matrix provided state of the art composite mechanical properties before and after humidity exposure and an anaerobic char yield of 46 percent at 800 C. The outstanding moisture resistance of the matrix was not completely realized in the composite. Vinyl ester resins showed promise as candidates for improved composite matrix systems.

  5. Natural fiber reinforced composites with moringa and vnyl ester matrix

    OpenAIRE

    Sundara, Babu Jagannathan

    2015-01-01

    In this research work an attempt is carried out for producing a Natural Plant Based fiber Reinforced Composites using the Moringa Resins and Vinyl Ester by utilizing the wastage of natural plant based fiber as Reinforcement material and Matrix material as Natural Resin and Vinyl Ester. The objective of the work is Utilization of Natural Plant Based Bio- degardable wastage into an alternative materials in the industrial applications by analyzing, Various Manufacturing and testing. Initially th...

  6. Interacting Blends of Novel Unsaturated Polyester Amide Resin with Styrene

    OpenAIRE

    Patel, Hasmukh S.; Panchal, Kumar K.

    2004-01-01

    Novel unsaturated poly (ester-amide) resins (UPEAs) were prepared by the reaction between an epoxy resin, namely diglycidyl ether of bisphenol–A (DGEBA) and unsaturated aliphatic bisamic acids using a base catalyst. These UPEAs were then blended with a vinyl monomer namely, Styrene (STY.) to produce a homogeneous resin syrup. The curing of these UPEAs-STY. resin blends was carried out by using benzoyl peroxide (BPO) as a catalyst and was monitored by using a differential scanning calorimeter ...

  7. Cost and Performance Report: Low-Hazardous Air Pollutant (HAP)/Volatile Organic Compound (VOC)-Compliant Resins for Military Applications

    Science.gov (United States)

    2012-03-01

    acid chain length decrease (4), but cost is also a factor. Methacrylated lauric acid monomers represent a balance of these factors...affects the cost. Shorter fatty acids , such as octanoic acid , are more expensive than longer acids , such as lauric acid . Novolac resins are more... acid vinyl ester resin system FAVE-L fatty acid vinyl ester resin system based on lauric acid FAVE-O fatty acid vinyl ester resin system based

  8. Epoxy hydantoins as matrix resins

    Science.gov (United States)

    Weiss, J.

    1983-01-01

    Tensile strength and fracture toughness of castings of the hydantoin resins cured with methylenedianiline are significantly higher than MY 720 control castings. Water absorption of an ethyl, amyl hydantoin formulation is 2.1 percent at equilibrium and Tg's are about 160 C, approximately 15 deg below the final cure temperature. Two series of urethane and ester-extended hydantoin epoxy resins were synthesized to determine the effect of crosslink density and functional groups on properties. Castings cured with methylenedianiline or with hexahydrophthalic anhydride were made from these compounds and evaluated. The glass transition temperatures, tensile strengths and moduli, and fracture toughness values were all much lower than that of the simple hydantoin epoxy resins. Using a methylene bishydantoin epoxy with a more rigid structure gave brittle, low-energy fractures, while a more flexible, ethoxy-extended hydantoin epoxy resin gave a very low Tg.

  9. Studies on novel interpenetrating networks of urethane modified poly(ester-amide and vinyl ester of bisphenol-C

    Directory of Open Access Journals (Sweden)

    Pragnesh N. Dave

    2016-05-01

    Full Text Available Bisphthalamic acids were prepared by reaction of maleic anhydride and aromatic diamines. Novel poly(ester-amides (PEAs were prepared by reaction of DGEBF with bisphthalamic acids. Acrylation of PEAs was carried out using acryloyl chloride; products are called acrylated poly(ester-amides (APEAs. Epoxy resin based unsaturated poly(ester-amide resins (UPEAs can be prepared by many methods but here these were prepared by reported method. These UPEAs were then treated with acryloyl chloride to afford acrylated UPEAs resin (i.e. AUPEAs. Interpenetrating networks of equal proportional urethane modified poly(ester-amide and acrylated poly(ester-amide and vinyl ester of biaphenol c (VE resin were prepared. Urethane modified APEAs and AUPEAs were characterized by elemental analysis, molecular weight was determined by vapor pressure osmometer and by IR spectral study and by thermogravimetry. Based on DSC data in situ glass reinforced composites of the resultant blends have been prepared and characterized for mechanical, electrical and chemical properties. Unreinforced blends were characterized by thermogravimetry (TGA.

  10. Comparison of XAD macroporous resins for the concentration of fulvic acid from aqueous solution

    Science.gov (United States)

    Aiken, G.R.

    1979-01-01

    Five macroreticular, nonlonlc AmberlHe XAD resins were evaluated for concentration and Isolation of fulvlc acid from aqueous solution. The capacity of each resin for fulvlc acid was measured by both batch and column techniques. Elution efficiencies were determined by desorptlon with 0.1 N NaOH. Highest recoveries were obtained with the acrylic ester resins which proved to be most efficient for both adsorption and elution of fulvlc acid. Compared to the acrylic ester resins, usefulness of the styrene dvlnybenzene resins to remove fulvlc acid is limited because of slow diffusion-controlled adsorption and formation of charge-transfer complexes, which hinders elution. ?? 1979 American Chemical Society.

  11. Enhanced Cyanate Ester Nanocomposites through Improved Nanoparticle Surface Interactions

    Science.gov (United States)

    2013-05-09

    uptake properties and processability of cyanate ester resins . This work seeks to better understand the root of these improvements by comparing thermal and...Sensing 4 Distribution A: Approved for public release; distribution is unlimited. Known Unknowns • Particle Dispersion • Resin Cure – Is there a...breaks up agglomeration, but not completely. 7 Distribution A: Approved for public release; distribution is unlimited. Water Removal TGA of As

  12. Paramagnetic epoxy resin

    Directory of Open Access Journals (Sweden)

    E. C. Vazquez Barreiro

    2017-01-01

    Full Text Available This work illustrates that macrocycles can be used as crosslinking agents for curing epoxy resins, provided that they have appropriate organic functionalities. As macrocycles can complex metal ions in their structure, this curing reaction allows for the introduction of that metal ion into the resin network. As a result, some characteristic physical properties of the metallomacrocycle could be transferred to the new material. The bisphenol A diglycidyl ether (BADGE, n = 0 and hemin (a protoporphyrin IX containing the Fe(III ion, and an additional chloride ligand have been chosen. The new material has been characterized by differential scanning calorimetry (DSC, thermogravimetric analysis (TGA, Fourier Transform Infrared (FT-IR, Nuclear Magnetic Resonance (NMR, Transmission Electron Microscopy (TEM, and magnetic susceptibility measurements. Fe(III remains in the high-spin state during the curing process and, consequently, the final material exhibits the magnetic characteristics of hemin. The loss of the chlorine atom ligand during the cure of the resin allows that Fe(III can act as Lewis acid, catalyzing the crosslinking reactions. At high BADGE n = 0/hemin ratios, the formation of ether and ester bonds occurs simultaneously during the process.

  13. Studies on Viscoelastic, Thermal and Morphological Properties of Vinyl Ester – Mixed Diluents System

    Directory of Open Access Journals (Sweden)

    Ranjan Jagesh Kumar

    2017-09-01

    Full Text Available Vinyl ester resin networks formed by using mixture of diluents were prepared. Methyl methacrylate (MMA diluent was mixed in various proportions with vinyl ester resin which was already premixed with styrene diluent (45 wt. %. Weight ratios e.g. 80:20, 70:30 and 60:40 of VE resin: MMA diluents were studied. Viscoelastic properties of the cross-linked resin were studied by dynamic mechanical analyzer in terms of storage modulus and tanδ. Thermal analysis was performed using non-isothermal mode of Differential scanning calorimetry. The samples with mixed diluents, showed higher modulus, and glass transition temperature in comparison to that of the pure vinyl ester-styrene resin cross-linked in presence of styrene only. The difference in thermal stability between vinyl ester-styrene and vinyl ester-MMA-styrene was checked. Vinyl Ester - 20 wt. % MMA-Styrene samples have the best thermal property among all other prepared samples. Multiphase morphology was formed for the thermoset crosslinked with mixed diluents in contrast to that formed with single diluent. With increase in MMA content in the resin dispersed domain size increased.

  14. Solidification of ion exchange resin wastes

    International Nuclear Information System (INIS)

    1982-08-01

    Solidification media investigated included portland type I, portland type III and high alumina cements, a proprietary gypsum-based polymer modified cement, and a vinyl ester-styrene thermosetting plastic. Samples formulated with hydraulic cement were analyzed to investigate the effects of resin type, resin loading, waste-to-cement ratio, and water-to-cement ratio. The solidification of cation resin wastes with portland cement was characterized by excessive swelling and cracking of waste forms, both after curing and during immersion testing. Mixed bed resin waste formulations were limited by their cation component. Additives to improve the mechanical properties of portland cement-ion exchange resin waste forms were evaluated. High alumina cement formulations dislayed a resistance to deterioration of mechanical integrity during immersion testing, thus providing a significant advantage over portland cements for the solidification of resin wastes. Properties of cement-ion exchange resin waste forms were examined. An experiment was conducted to study the leachability of 137 Cs, 85 Sr, and 60 Co from resins modified in portland type III and high alumina cements. The cumulative 137 Cs fraction release was at least an order of magnitude greater than that of either 85 Sr or 60 Co. Release rates of 137 Cs in high alumina cement were greater than those in portland III cement by a factor of two.Compressive strength and leach testing were conducted for resin wastes solidified with polymer-modified gypsum based cement. 137 Cs, 85 Sr, and 60 Co fraction releases were about one, two and three orders of magnitude higher, respectively, than in equivalent portland type III cement formulations. As much as 28.6 wt % dry ion exchange resin was successfully solidified using vinyl ester-styrene compared with a maximum of 25 wt % in both portland and gypsum-based cement

  15. Interacting Blends of Novel Unsaturated Polyester Amide Resin with Vinyl Acetate

    OpenAIRE

    Patel, H. S.; Panchal, K. K.; Patel, S. R.; Desai, S. N.

    2004-01-01

    Novel unsaturated poly (ester- amide) resins (UPEAs) were prepared by the reaction between an epoxy resin, namely diglycidyl ether of bisphenol–A (DGEBA) and unsaturated aliphatic bisamic acids using a base catalyst. These UPEAs were then blended with a vinyl monomer namely, Vinyl acetate (VA) to produce a homogeneous resin syrup. The curing of these UPEAs-VA resin blends was carried out by using benzoyl peroxide (BPO) as an initiator for the radical polymerization and was monitored by using ...

  16. Cyanate Ester-Based Encapsulation Material for High-Temperature Applications

    Science.gov (United States)

    Chidambaram, Vivek; Rong, Eric Phua Jian; Lip, Gan Chee; Daniel, Rhee Min Woo

    2013-09-01

    Cyanate ester resin-based composite materials have been proposed as potential encapsulants for high-temperature applications. The objective of this study is to develop a cyanate ester-based encapsulant, which can also serve as a flip-chip underfill as well as for traditional encapsulation. Two different materials, quartz and alumina fillers, have been studied. The impact of shapes and sizes of the fillers on the overall thermomechanical properties has been investigated. The adhesion strengths of the materials to the ceramic substrate, Kovar lid, and silicon die have also been characterized. The modulus of the resin and the shape of the fillers play a pivotal role in minimizing thermal stress, generated by coefficient of thermal expansion mismatches. Smaller filler particles were found to have better adhesion to the cyanate ester resin. The high-temperature performance of the cyanate ester-based encapsulants was evaluated by thermal aging at 300°C for up to 500 h.

  17. Plastic casting resin poisoning

    Science.gov (United States)

    Epoxy poisoning; Resin poisoning ... Epoxy and resin can be poisonous if they are swallowed or their fumes are breathed in. ... Plastic casting resins are found in various plastic casting resin products.

  18. Resin composites

    DEFF Research Database (Denmark)

    Benetti, Ana Raquel; Peutzfeldt, Anne; Lussi, Adrian

    2014-01-01

    OBJECTIVE: To investigate how the modulus of elasticity of resin composites influences marginal quality in restorations submitted to thermocyclic and mechanical loading. METHODS: Charisma, Filtek Supreme XTE and Grandio were selected as they were found to possess different moduli of elasticity...... of resin composite (p=0.81) on the quality of dentine margins was observed, before or after loading. Deterioration of all margins was evident after loading (p....008). CONCLUSIONS: The resin composite with the highest modulus of elasticity resulted in the highest number of gap-free enamel margins but with an increased incidence of paramarginal enamel fractures. CLINICAL SIGNIFICANCE: The results from this study suggest that the marginal quality of restorations can...

  19. Ester Tuiksoo / Ester Tuiksoo ; interv. Piret Tali

    Index Scriptorium Estoniae

    Tuiksoo, Ester, 1965-

    2007-01-01

    Juhan Partsi valitsuse (05.04.2004-13.04.2005) ja Andrus Ansipi valitsuse (13.04.2005-) põllumajandusminister Ester Tuiksoo oma lapsepõlvest ja elukutsevalikust, poliitilise karjääri algusest ja erakonna valikust, ministritöö kogemustest, naistest poliitikas

  20. Interacting Blends of Novel Unsaturated Polyester Amide Resin with Styrene

    Directory of Open Access Journals (Sweden)

    Hasmukh S. Patel

    2004-01-01

    Full Text Available Novel unsaturated poly (ester-amide resins (UPEAs were prepared by the reaction between an epoxy resin, namely diglycidyl ether of bisphenol–A (DGEBA and unsaturated aliphatic bisamic acids using a base catalyst. These UPEAs were then blended with a vinyl monomer namely, Styrene (STY. to produce a homogeneous resin syrup. The curing of these UPEAs-STY. resin blends was carried out by using benzoyl peroxide (BPO as a catalyst and was monitored by using a differential scanning calorimeter (DSC. The glass fibre reinforced composites (i.e. laminates of these UPEA-STY. resin blends were fabricated using the DSC data. The chemical, mechanical and electrical properties of the glass fibre composites have also been evaluated. The unreinforced cured samples of the UPEA-STY. resin blends were also analyzed by thermogravimetry (TGA.

  1. Low HAP/VOC Compliant Resins for Military Applications

    Science.gov (United States)

    2011-09-01

    on lauric acid FAVE-O fatty acid vinyl ester resin system based on octanoic acid FTIR Fourier transform infrared GIC Mode 1 fracture energy... lauric acid MOct methacrylated octanoic acid MPa megapascals Msi 1 million lb per square inch mW mega watt NESHAP National Emissions Standard... lauric acid (MLau) monomers represent a balance of these factors, as they have good resin and polymer properties, and low cost. Due to the low cost of

  2. Ionization radiation curable polyacrylate resin coatings

    International Nuclear Information System (INIS)

    Miller, L.S.

    1975-01-01

    A carboxylic acid chloride or bromide, a sulfonyl chloride or bromide, cyanuric chloride, calcium hypochlorite or phosphorus oxychloride and optionally a buffering pigment are combined with a liquid, acrylate ester resin curable by exposure to high-energy ionizing radiation to yield a coating composition which upon being cured in air by exposure to ionizing radition yields a coating having an essentially tack-free surface. (Patent Office Record)

  3. Two cases of occupational allergic contact dermatitis from a cycloaliphatic epoxy resin in a neat oil

    DEFF Research Database (Denmark)

    Jensen, Charlotte D; Andersen, Klaus E

    2003-01-01

    to a neat oil used in metal processing. Patch testing revealed that the relevant contact allergen was a cycloaliphatic epoxy resin, 1,2-cyclohexanedicarboxylic acid, bis(oxiranylmethyl) ester, added to the oil as a stabilizer. None of the patients had positive reactions to the bisphenol A-based epoxy resin...... product is essential....

  4. A New Resin Glycoside, Muricatin IX, from the Seeds of Ipomoea muricata.

    Science.gov (United States)

    Ono, Masateru; Taketomi, Saki; Kakiki, Yuichi; Yasuda, Shin; Okawa, Masafumi; Kinjo, Junei; Yoshimitsu, Hitoshi; Nohara, Toshihiro

    2016-01-01

    A new resin glycoside, named muricatin IX (1), was isolated from the seeds of Ipomoea muricata (L.) JACQ. (Convolvulaceae). The structure of 1 was determined on the basis of spectroscopic data as well as chemical evidence. Compound 1 is the first representative of resin glycosides in which an organic acid connects the sugar moiety and the aglycone moiety to form macrocyclic ester ring.

  5. Studies concerning the anion ex-change resins catalyzed esterification of epichlorohydrin with organic acids

    Directory of Open Access Journals (Sweden)

    E.I. Muresan

    2009-09-01

    Full Text Available The paper studies the esterification of carboxylic acids with epichlorohydrin over two macroporous strong base anion exchange resins with different polymer matrix. For both resins, the influence of reaction parameters (temperature, catalyst loading, molar ratio on the reaction rate and the yields of the two isomeric esters were investigated.

  6. Review: Resin Composite Filling

    OpenAIRE

    Desmond Ng; Jimmy C. M. Hsiao; Keith C. T. Tong; Harry Kim; Yanjie Mai; Keith H. S. Chan

    2010-01-01

    The leading cause of oral pain and tooth loss is from caries and their treatment include restoration using amalgam, resin, porcelain and gold, endodontic therapy and extraction. Resin composite restorations have grown popular over the last half a century because it can take shades more similar to enamel. Here, we discuss the history and use of resin, comparison between amalgam and resin, clinical procedures involved and finishing and polishing techniques for resin restoration. Although resin ...

  7. Resin Characterization

    Science.gov (United States)

    2015-06-01

    to see plastic deformation of the surface. 8.1.4.3 Density: Density using the Archimedes principle (ASTM D 792). 8.1.4.4 Density as a Function of...the cure and postcure, quickly cool the sample to 0 °C or lower the temperature to quench the reaction, and then ramp the temperature at 5 °C/min to...prepared by pouring 10 g of resin into a 30-mL screw-cap scintillation vial and adding appropriate amounts of initiator, catalyst, and inhibitor

  8. Maximization of fructose esters synthesis by response surface methodology.

    Science.gov (United States)

    Neta, Nair Sampaio; Peres, António M; Teixeira, José A; Rodrigues, Ligia R

    2011-07-01

    Enzymatic synthesis of fructose fatty acid ester was performed in organic solvent media, using a purified lipase from Candida antartica B immobilized in acrylic resin. Response surface methodology with a central composite rotatable design based on five levels was implemented to optimize three experimental operating conditions (temperature, agitation and reaction time). A statistical significant cubic model was established. Temperature and reaction time were found to be the most significant parameters. The optimum operational conditions for maximizing the synthesis of fructose esters were 57.1°C, 100 rpm and 37.8 h. The model was validated in the identified optimal conditions to check its adequacy and accuracy, and an experimental esterification percentage of 88.4% (±0.3%) was obtained. These results showed that an improvement of the enzymatic synthesis of fructose esters was obtained under the optimized conditions. Copyright © 2011 Elsevier B.V. All rights reserved.

  9. Immobilization of spent resin with epoxy resin

    International Nuclear Information System (INIS)

    Gultom, O.; Suryanto; Sayogo; Ramdan

    1997-01-01

    immobilization of spent resin using epoxy resin has been conducted. The spent resin was mixtured with epoxy resin in variation of concentration, i.e., 30, 40, 50, 60, 70 weight percent of spent resin. The mixture were pour into the plastic tube, with a diameter of 40 mm and height of 40 mm. The density, compressive strength and leaching rate were respectively measured by quanta chrome, paul weber apparatus and gamma spectrometer. The results showed that the increasing of waste concentration would be decreased the compressive strength, and increased density by immobilized waste. The leaching rate of 137 Cs from waste product was not detected in experiment (author)

  10. Sustainable, Green Vinyl Ester Resin (VER) from Renewable Resources

    Science.gov (United States)

    2017-04-02

    134 Figure 138. Experimental “degree of cure” profiles for GVER-1 at 3 different temperatures ... 135 Figure 139. Comparison...by MSB in the manufacture of Biodiesel is used vegetable oil sourced from numerous restaurants in the New England area. Currently, they ship the...concentration resulted in very fast reaction and 4 h, all nonfunctional TBBPA was consumed and 28.7 % of the monofunctional TBBPA remained in the system as

  11. Cyanate Ester Composite Resins Derived from Renewable Polyphenol Sources

    Science.gov (United States)

    2011-03-16

    Stop 6303 China Lake, CA 93555-6106 Lead Principal Investigator: Dr. Benjamin G. Harvey 760-939-0247 (phone) 760-939-1617...N. Knox Road, Stop 6303 China Lake, CA 93555 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10. SPONSOR/MONITOR’S ACRONYM(S) Strategic...The reaction was allowed to proceed for 1.5 hours, at which point TLC showed the reaction to be incomplete. At this point an additional 0.5

  12. A Comparative Study on the Thermal Resistance, Flammability and Mechanical Properties of Unsaturated Polyester and Epoxy Resins

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Fathizadeh

    2015-11-01

    Full Text Available Thermal properties, flammability and mechanical properties of three different kinds of unsaturated polyester resins, ortho, iso and vinyl ester and an epoxy resin based on diglycidyl ether of bisphenol-A were investigated. Since these resins are widely used in the composite industry it is vital to recognize their properties. For this purpose, viscosity, burning rate, limiting oxygen index (LOI and flexural properties were measured. Fourier transform infrared (FTIR spectroscopy and thermal gravimetric analysis were also performed. The viscosity of unsaturated polyester resins which was in the range of 300 to 450 cp showed an advantage compared to the viscosity of epoxy resin which was in the range of 600 to 1000 cp. The low viscosity property which is usually seen in unsaturated polyester resins is very important from the processing point of view, which in turn helps to ensure a simple processing. The ortho resin showed the highest conversion and conversion rate among the three unsaturated polyester resins. The vinyl ester resin showed a higher conversion than the iso resin. The results showed that the vinyl ester resin had the highest thermal resistance, flammability and mechanical properties among the unsaturated polyester resins used in this work. On the other hand, although the epoxy resin showed the highest burning rate but it had the highest carbon residue or char yield (12.4% and LOI (20.2%, and consequently the highest thermal resistance. The results of flexural test showed that the epoxy resin had the highest flexural strength (116 MPa and modulus (4.1 GPa and the lowest deflection-at-break (2.8% and toughness in comparison with the unsaturated polyester resins used in this work.

  13. Valyl benzyl ester chloride

    Directory of Open Access Journals (Sweden)

    Grzegorz Dutkiewicz

    2010-02-01

    Full Text Available In the title compound (systematic name: 1-benzyloxy-3-methyl-1-oxobutan-2-aminium chloride, C12H18NO2+·Cl−, the ester group is approximately planar, with a maximum deviation of 0.040 (2 Å from the least-squares plane, and makes a dihedral angle of 28.92 (16° with the phenyl ring. The crystal structure is organized by N—H...Cl hydrogen bonds which join the two components into a chain along the b axis. Pairs of chains arranged antiparallel are interconnected by further N—H...Cl hydrogen bonds, forming eight-membered rings. Similar packing modes have been observed in a number of amino acid ester halides with a short unit-cell parameter of ca 5.5 Å along the direction in which the chains run.

  14. Lignin model compounds as bio-based reactive diluents for liquid molding resins.

    Science.gov (United States)

    Stanzione, Joseph F; Sadler, Joshua M; La Scala, John J; Wool, Richard P

    2012-07-01

    Lignin is a copious paper and pulping waste product that has the potential to yield valuable, low molecular weight, single aromatic chemicals when strategically depolymerized. The single aromatic lignin model compounds, vanillin, guaiacol, and eugenol, were methacrylated by esterification with methacrylic anhydride and a catalytic amount of 4-dimethylaminopyridine. Methacrylated guaiacol (MG) and methacrylated eugenol (ME) exhibited low viscosities at room temperature (MG: 17 cP and ME: 28 cP). When used as reactive diluents in vinyl ester resins, they produced resin viscosities higher than that of vinyl ester-styrene blends. The relative volatilities of MG (1.05 wt% loss in 18 h) and ME (0.96 wt% loss in 18 h) measured by means of thermogravimetric analysis (TGA) were considerably lower than that of styrene (93.7 wt% loss in 3 h) indicating the potential of these chemicals to be environmentally friendly reactive diluents. Bulk polymerization of MG and ME generated homopolymers with glass transition temperatures (T(g)s) of 92 and 103 °C, respectively. Blends of a standard vinyl ester resin with MG and ME (50 wt % reactive diluent) produced thermosets with T(g)s of 127 and 153 °C, respectively, which are comparable to vinyl ester-styrene resins, thus demonstrating the ability of MG and ME to completely replace styrene as reactive diluents in liquid molding resins without sacrificing cured-resin thermal performance. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Review: Resin Composite Filling

    Directory of Open Access Journals (Sweden)

    Desmond Ng

    2010-02-01

    Full Text Available The leading cause of oral pain and tooth loss is from caries and their treatment include restoration using amalgam, resin, porcelain and gold, endodontic therapy and extraction. Resin composite restorations have grown popular over the last half a century because it can take shades more similar to enamel. Here, we discuss the history and use of resin, comparison between amalgam and resin, clinical procedures involved and finishing and polishing techniques for resin restoration. Although resin composite has aesthetic advantages over amalgam, one of the major disadvantage include polymerization shrinkage and future research is needed on reaction kinetics and viscoelastic behaviour to minimize shrinkage stress.

  16. Review: Resin Composite Filling

    Science.gov (United States)

    Chan, Keith H. S.; Mai, Yanjie; Kim, Harry; Tong, Keith C. T.; Ng, Desmond; Hsiao, Jimmy C. M.

    2010-01-01

    The leading cause of oral pain and tooth loss is from caries and their treatment include restoration using amalgam, resin, porcelain and gold, endodontic therapy and extraction. Resin composite restorations have grown popular over the last half a century because it can take shades more similar to enamel. Here, we discuss the history and use of resin, comparison between amalgam and resin, clinical procedures involved and finishing and polishing techniques for resin restoration. Although resin composite has aesthetic advantages over amalgam, one of the major disadvantage include polymerization shrinkage and future research is needed on reaction kinetics and viscoelastic behaviour to minimize shrinkage stress.

  17. Influence of the molecular structure on hydrolyzability of epoxy resins

    International Nuclear Information System (INIS)

    Pays, M.F.

    1996-01-01

    EDF has decided to use glass reinforced composites for certain pipework in Pressurized Water Reactors (service water, emergency-supplied service water, fine pipe works, etc...) as a replacement for traditional materials. In practice, steel is prone to rapid corrosion in these circuits; introducing composites could prove economically viable if their long term behaviour can be demonstrated. However, composite materials can undergo deterioration in service through hydrolysis of the resin or the fibre-matrix interface. Different resins can be chosen depending on the programmed use. A first study has covered the hydrolyzability of polyester and vinyl ester resins. The present document undertakes the resistance to hydrolysis of epoxy resins, concentrating on those reputed to withstand high temperatures. This research uses model monomer, linking the molecular structure of the materials to their resistance to hydrolysis. (author)

  18. Method of making alkyl esters

    Science.gov (United States)

    Elliott, Brian

    2010-09-14

    Methods of making alkyl esters are described herein. The methods are capable of using raw, unprocessed, low-cost feedstocks and waste grease. Generally, the method involves converting a glyceride source to a fatty acid composition and esterifying the fatty acid composition to make alkyl esters. In an embodiment, a method of making alkyl esters comprises providing a glyceride source. The method further comprises converting the glyceride source to a fatty acid composition comprising free fatty acids and less than about 1% glyceride by mass. Moreover, the method comprises esterifying the fatty acid composition in the presence of a solid acid catalyst at a temperature ranging firm about 70.degree. C. to about 120.degree. C. to produce alkyl esters, such that at least 85% of the free fatty acids are converted to alkyl esters. The method also incorporates the use of packed bed reactors for glyceride conversion and/or fatty acid esterification to make alkyl esters.

  19. Resin-Powder Dispenser

    Science.gov (United States)

    Standfield, Clarence E.

    1994-01-01

    Resin-powder dispenser used at NASA's Langley Research Center for processing of composite-material prepregs. Dispenser evenly distributes powder (resin polymer and other matrix materials in powder form) onto wet uncured prepregs. Provides versatility in distribution of solid resin in prepreg operation. Used wherever there is requirement for even, continuous distribution of small amount of powder.

  20. Apomorphine and its esters

    DEFF Research Database (Denmark)

    Borkar, Nrupa; Chen, Zhizhong; Saaby, Lasse

    2016-01-01

    Oral delivery of apomorphine via prodrug principle may be a potential treatment for Parkinson's disease. The purpose of this study was to investigate the transport and stability of apomorphine and its esters across Caco-2 cell monolayer and their affinity towards chylomicrons. Apomorphine......, monolauroyl apomorphine (MLA) and dilauroyl apomorphine (DLA) were subjected to apical to basolateral (A-B) and basolateral to apical (B-A) transport across Caco-2 cell monolayer. The stability of these compounds was also assessed by incubation at intestinal pH and physiological pH with and without Caco-2...

  1. Esters with water esters 2-c to 6-c

    CERN Document Server

    Getzen, F W; Hefter, G T; Maczynski, Andrzej

    1992-01-01

    This volume is the first of two devoted to esters and water. It includes solubility data for binary systems containing an ester and water up to the end of 1988. The critical evaluations were all prepared by one author and an introductory section has been included to elaborate the philosophy and methodology followed in the evaluations.

  2. The resin glycosides from the sweet potato (Ipomoea batatas L. LAM.).

    Science.gov (United States)

    Noda, Naoki; Horiuchi, Yoshinori

    2008-11-01

    Four new and two known ether-soluble resin glycosides were isolated from popular sweet potato (the roots of Ipomoea batatas L. LAM., Kokei 14 go, Convolvulaceae) in Japan. Unlike ester-type dimers, batatins I and II, obtained from other sweet potato (Ipomoea batabas var. batatas), the glycosides were tetra or pentasaccharide monomers in which the sugar moieties are partially acylated by organic acids and combine with the aglycone, jalapinolic acid, to form a macrocyclic ester.

  3. Rheological and dynamic-mechanical behavior of carbon nanotube/vinyl ester-polyester suspensions and their nanocomposites

    OpenAIRE

    Seyhan, Abdullah Tuğrul; Gojny, F. H.; Tanoğlu, Metin; Schulte, K.

    2007-01-01

    Rheological properties of vinyl ester-polyester resin suspensions containing various amounts (0.05, 0.1 and 0.3 wt.%) of multi walled carbon nanotubes (MWCNT) with and without amine functional groups (-NH2) were investigated by utilization of oscillatory rheometer with parallel plate geometry. Dispersion of corresponding carbon nanotubes within the resin blend was accomplished employing high shear mixing technique (3-roll milling). Based on the dynamic viscoelastic measurements, it was observ...

  4. Fossilization History of Fossil Resin from Jambi Province (Sumatra, Indonesia Based on Physico-Chemical Studies

    Directory of Open Access Journals (Sweden)

    Beata Naglik

    2018-03-01

    Full Text Available A unique specimen of fossil resin originating from the Dipterocarpaceae tree family found in Miocene brown coal deposits in Jambi Province (Sumatra, Indonesia was investigated via microscopic observations, microhardness testing and infrared and Raman spectroscopic methods. Its form is rare in nature, being an aggregate of three varieties of resin differing in colour, transparency and internal structure. This suggests the formation of the resins at different stages. Further alteration processes, including fossilization and maturation of the resin in a swamp environment resulted in stepwise aromatization of the cyclohexane ring in steroids and cross-linking through formation of ester bonds as well as carbon–carbon bonds between steroid molecules. The various environmental and geological conditions affecting the formation processes of the resins were recorded in their physico-chemical properties. Additionally, heating conditions accelerated by volcanism were proposed as a factor determining the maturation grade of the resin.

  5. Interacting Blends of Novel Unsaturated Polyester Amide Resin with Vinyl Acetate

    Directory of Open Access Journals (Sweden)

    H. S. Patel

    2004-01-01

    Full Text Available Novel unsaturated poly (ester- amide resins (UPEAs were prepared by the reaction between an epoxy resin, namely diglycidyl ether of bisphenol–A (DGEBA and unsaturated aliphatic bisamic acids using a base catalyst. These UPEAs were then blended with a vinyl monomer namely, Vinyl acetate (VA to produce a homogeneous resin syrup. The curing of these UPEAs-VA resin blends was carried out by using benzoyl peroxide (BPO as an initiator for the radical polymerization and was monitored by using a differential scanning calorimeter (DSC. The glass fibre reinforced composites (i.e. laminates of these UPEA-VA resin blends were fabricated using the DSC data. The chemical, mechanical and electrical properties of the glass fibre composites have also been evaluated. The unreinforced cured samples of the UPEA-VA resin blends were also analyzed by thermogravimetry (TGA.

  6. Properties of halloysite nanotube-epoxy resin hybrids and the interfacial reactions in the systems

    Energy Technology Data Exchange (ETDEWEB)

    Liu Mingxian; Guo Baochun; Du Mingliang; Cai Xiaojia; Jia Demin [Department of Polymer Materials and Engineering, South China University of Technology, Guangzhou 510640 (China)

    2007-11-14

    A naturally occurred microtubullar silicate, halloysite nanotubes (HNTs), was co-cured with epoxy/cyanate ester resin to form organic-inorganic hybrids. The coefficient of thermal expansion (CTE) of the hybrids with low HNT concentration was found to be substantially lower than that of the plain cured resin. The moduli of the hybrids in the glassy state and rubbery state were significantly higher than those for the plain cured resin. The dispersion of HNTs in the resin matrix was very uniform as revealed by the transmission electron microscopy (TEM) results. The interfacial reactions between the HNTs and cyanate ester (CE) were revealed by the results of Fourier transform infrared spectroscopy (FTIR) and x-ray photoelectron spectroscopy (XPS). The substantially increased properties of the hybrids were attributed to the covalent bonding between the nanotubes and the matrix.

  7. Properties of halloysite nanotube epoxy resin hybrids and the interfacial reactions in the systems

    Science.gov (United States)

    Liu, Mingxian; Guo, Baochun; Du, Mingliang; Cai, Xiaojia; Jia, Demin

    2007-11-01

    A naturally occurred microtubullar silicate, halloysite nanotubes (HNTs), was co-cured with epoxy/cyanate ester resin to form organic-inorganic hybrids. The coefficient of thermal expansion (CTE) of the hybrids with low HNT concentration was found to be substantially lower than that of the plain cured resin. The moduli of the hybrids in the glassy state and rubbery state were significantly higher than those for the plain cured resin. The dispersion of HNTs in the resin matrix was very uniform as revealed by the transmission electron microscopy (TEM) results. The interfacial reactions between the HNTs and cyanate ester (CE) were revealed by the results of Fourier transform infrared spectroscopy (FTIR) and x-ray photoelectron spectroscopy (XPS). The substantially increased properties of the hybrids were attributed to the covalent bonding between the nanotubes and the matrix.

  8. Mechanical and Thermal Properties of Unsaturated Polyester/Vinyl Ester Blends Cured at Room Temperature

    Science.gov (United States)

    Ardhyananta, H.; Puspadewa, F. D.; Wicaksono, S. T.; Widyastuti; Wibisono, A. T.; Kurniawan, B. A.; Ismail, H.; Salsac, A. V.

    2017-05-01

    Unsaturated polyester (UP) resin containing aromatic ring was blended with vinyl ester (VE) at wide range composition (10, 20, 30, 40,and 80 wt.%) using mechanical blending method. The blends were cured at room temperature using methyl ethyl ketone peroxide (MEKP) (4 wt.%) as catalyst initiator without the presence of catalystaccelerator. The effect of vinyl ester composition on theenhancement of mechanical and thermal properties of unsaturated polyester/vinyl ester blends was investigated. The polymer blends were characterized by Fourier Transform Infra Red (FTIR)spectroscopy, tensile testing, hardness testing, scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). IR spectra showed UP and VE peaks. The curing copolymerization reactionoccurred at vinyl (C=C) bonds. The addition of vinyl esters enhanced mechanical and thermal properties. The UP/VE blends showed homogeneous morphology, transparent and copolymer thermoset blend.

  9. Carboxylic ester hydrolases from hyperthermophiles

    NARCIS (Netherlands)

    Levisson, M.; Oost, van der J.; Kengen, S.W.M.

    2009-01-01

    Carboxylic ester hydrolyzing enzymes constitute a large group of enzymes that are able to catalyze the hydrolysis, synthesis or transesterification of an ester bond. They can be found in all three domains of life, including the group of hyperthermophilic bacteria and archaea. Esterases from the

  10. Lipoate ester multifunctional lubricant additives

    Science.gov (United States)

    Seven lipoate esters were synthesized by esterification of lipoic acid with different structures of alcohols in the presence of a solid acid catalyst and without solvent. The esters were obtained in good yield, characterized using 1H NMR and GPC; and their physical properties investigated. Four of t...

  11. Esters production via carboxylates from anaerobic paper mill wastewater treatment.

    Science.gov (United States)

    Cabrera-Rodríguez, Carlos I; Moreno-González, Mónica; de Weerd, Florence A; Viswanathan, Vidhvath; van der Wielen, Luuk A M; Straathof, Adrie J J

    2017-08-01

    This paper describes a new option for integrated recovery and esterification of carboxylates produced by anaerobic digestion at a pH above the pK a . The carboxylates (acetate, propionate, butyrate, valerate and lactate) are recovered using a strong anion exchange resin in the bicarbonate form, and the resin is regenerated using a CO 2 -expanded alcohol technique, which allows for low chemicals consumption and direct esterification. Paper mill wastewater was used to study the effect of pH and the presence of other inorganic anions and cations on the adsorption and desorption with CO 2 -expanded methanol. Calcium, which is present in paper mill wastewater, can cause precipitation problems, especially at high pH. Esters yields ranged from 1.08±0.04mol methyl acetate/mol of acetate in to 0.57±0.02mol methyl valerate/mol of valerate in . Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Synthesis and Properties of a Novel Environmental Epoxidized Glycidyl Ester of Ricinoleic Acetic Ester Plasticizer for Poly(vinyl chloride

    Directory of Open Access Journals (Sweden)

    Jie Chen

    2017-11-01

    Full Text Available A novel renewable plasticizer based on castor oil, epoxidized glycidyl ester of ricinoleic acetic ester (EGERAE, was synthesized and applied into Poly(vinyl chloride (PVC for the first time. Its molecular structure was characterized by FT-IR and 1H NMR. The effects of replacement of petroleum-based commercial plasticizer dioctyl phthalate (DOP with EGERAE in poly(vinyl chloride (PVC films were researched. Thermal stability, dynamic mechanical property and mechanical properties of PVC films were investigated with thermogravimetric analysis (TGA, dynamic mechanical analysis (DMA and tensile tests. The results indicated that this castor oil-based plasticizer was able to improve the thermal stability of PVC blends when partially of completely substituting for DOP. Furthermore, EGERAE endowed PVC resin with enhanced flexibility. In addition, the exudation, volatility and extraction resistance characteristics of plasticizers were researched. The degradation mechanism and possible interaction between EGERAE and PVC molecules in the plasticized system were also investigated.

  13. Environmentally Compliant Vinyl Ester Resin (VER) Composite Matrix Resin Derived from Renewable Resources

    Science.gov (United States)

    2011-11-01

    range of reactions of industrial importance. For example, it can be used for the production of acrolein , widely used for organic synthesis and...dry column of silica gel used to conduct chromatographic purification of reaction product. 5a.2 Procedure b.1.a Setup and testing of high-pressure...pressure reactor was pressurized to 1000psi nitrogen pressure and tested for leaks. No leaks were detected, indicating that the apparatus was ready

  14. Effect of resin system on the mechanical properties and water absorption of kenaf fibre reinforced laminates

    International Nuclear Information System (INIS)

    Rassmann, S.; Paskaramoorthy, R.; Reid, R.G.

    2011-01-01

    The objective of this study is to compare the mechanical and water absorption properties of kenaf (Hibiscus cannabinus L.) fibre reinforced laminates made of three different resin systems. The use of different resin systems is considered so that potentially complex and expensive fibre treatments are avoided. The resin systems used include a polyester, a vinyl ester and an epoxy. Laminates of 15%, 22.5% and 30% fibre volume fraction were manufactured by resin transfer moulding. The laminates were tested for strength and modulus under tensile and flexural loading. Additionally, tests were carried out on laminates to determine the impact energy, impact strength and water absorption. The results revealed that properties were affected in markedly different ways by the resin system and the fibre volume fraction. Polyester laminates showed good modulus and impact properties, epoxy laminates displayed good strength values and vinyl ester laminates exhibited good water absorption characteristics. Scanning electron microscope studies show that epoxy laminates fail by fibre fracture, polyester laminates by fibre pull-out and vinyl ester laminates by a combination of the two. A comparison between kenaf and glass laminates revealed that the specific tensile and flexural moduli of both laminates are comparable at the volume fraction of 15%. However, glass laminates have much better specific properties than the kenaf laminates at high fibre volume fractions for all three resins used.

  15. Development of a solid-phase 'asymmetric resin-capture-release' process: application of an ephedrine chiral resin in an approach to gamma-butyrolactones.

    Science.gov (United States)

    Kerrigan, Nessan J; Hutchison, Panee C; Heightman, Tom D; Procter, David J

    2004-09-07

    The potential of a solid-phase asymmetric resin-capture-release strategy for high-throughput synthesis has been evaluated. Fukuzawa's Sm(ii)-mediated, asymmetric approach to gamma-butyrolactones was selected to illustrate the feasibility of such a process. Alpha,beta-unsaturated esters immobilised on an ephedrine chiral resin have been applied in an asymmetric approach to gamma-butyrolactones. Lactone products are obtained in moderate isolated yields with selectivities up to 96% ee. In addition, we have shown that the ephedrine resin can be conveniently recovered and recycled although in some cases lower yields were obtained on reuse of the chiral resin. A short synthesis of a moderate DNA-binding microbial metabolite using asymmetric resin-capture-release is also described. Copyright 2004 The Royal Society of Chemistry

  16. OPTIMASI PRODUKSI METIL ESTER SULFONAT DARI METIL ESTER MINYAK JELANTAH

    Directory of Open Access Journals (Sweden)

    Sri Hidayati

    2012-11-01

    Full Text Available OPTIMATION OF METHYL ESTER SULFONATES PRODUCTION FROM WASTE COOKING METHYL ESTER. An experiment of sulfonation process of methyl ester to produce methyl ester sulfonates (MES was caried out using waste palm methyl ester and sulfuric acid as sulfonating agent with variation of H2SO4 concentration (60% (K1, 70% (K2, dan 80% (K3 and sulfonation time (60 minute (L1, 75 minute (L2 and 90 minute (L3 using factorial on Randomized Complete Design Block. The experiment result showed the best sulfonation condition present in 80% H2SO4 concentration and sulfonation time of 90 minutes.  The best characteristic of MES is produced showed surface tension of 27.35 dyne/cm, emulsion stability of 89.44%, acid value of 17.72 mg KOH/g and interfacial tension of 0.0361 dyne/cm at MES concentration of 2% in 10,000 ppm salinity water. Sebuah penelitian tentang proses produksi metil ester sulfonat menggunakan minyak bekas kelapa sawit dilakukan dengan menggunakan H2SO4 sebagai agen pensulfonasi dengan variasi konsentrasi H2SO4 (60% (K1, 70% (K2, dan 80% (K3 dan lama sulfonasi (60 menit (L1, 75 menit (L2 and 90 menit (L3 dengan menggunakan faktorial dalam Rancangan Kelompok Teracak Lengkap. Hasil penelitian menunjukkan bahwa kondisi proses sulfonasi terbaik terdapat pada konsentrasi H2SO4 80% dan lama reaksi 90 menit. Karakteristik Metil Ester Sulfonat (MES terbaik yang dihasilkan memperlihatkan nilai tegangan permukaan 27,35 dyne/cm, stabilitas emulsi 89,44%, nilai bilangan asam antara 17,72 mg KOH/g dan nilai tegangan antar muka pada konsentrasi MES 2% di dalam air dengan salinitas 10.000 ppm yaitu 0,0361 dyne/cm.

  17. A convenient procedure for the solid-phase synthesis of hydroxamic acids on PEGA resins

    DEFF Research Database (Denmark)

    Nandurkar, Nitin Subhash; Petersen, Rico; Qvortrup, Katrine

    2011-01-01

    An efficient method for the solid-phase synthesis of hydroxamic acids is described. The method comprises the nucleophilic displacement of esters immobilized on PEGA resins with hydroxylamine/sodium hydroxide in isopropanol. The hydroxyaminolysis protocol is compatible with a broad range of PEGA...

  18. Merremins A-G, resin glycosides from Merremia hederacea with multidrug resistance reversal activity.

    Science.gov (United States)

    Wang, Wen-qiong; Song, Wei-bin; Lan, Xiao-jing; Huang, Min; Xuan, Li-jiang

    2014-10-24

    Five new pentasaccharide resin glycosides, named merremins A-E (1-5), two new pentasaccharide resin glycoside methyl esters, named merremins F and G (6, 7), and four known resin glycosides, murucoidin IV, murucoidin V, stoloniferin IV, and murucoidin XVII, were obtained from the aerial parts of Merremia hederacea. This is the first report of resin glycosides obtained from M. hederacea. In addition, the new compounds can be divided into three types: those possessing an 18-membered ring (1-4), compound 5 with a 20-membered ring, and those with an acyclic core (6, 7). Furthermore, the different types of resin glycosides were evaluated for their multidrug resistance reversal activities. Compounds 1, 5, 6, and murucoidin V were noncytotoxic and enhanced the cytotoxicity of vinblastine by 2.3-142.5-fold at 25 μM. Compound 5 and murucoidin V, with 20-membered rings, were more active than compound 1, with an 18-membered ring.

  19. Enlightening the past: analytical proof for the use of Pistacia exudates in ancient Egyptian embalming resins.

    Science.gov (United States)

    Nicholson, Tim M; Gradl, Manuela; Welte, Beatrix; Metzger, Michael; Pusch, Carsten M; Albert, Klaus

    2011-12-01

    Mastic, the resinous exudate of the evergreen shrub Pistacia lentiscus, is frequently discussed as one of the ingredients used for embalming in ancient Egypt. We show the identification of mastic in ancient Egyptian embalming resins by an unambiguous assignment of the mastic triterpenoid fingerprint consisting of moronic acid, oleanonic acid, isomasticadienonic and masticadienonic acid through the consolidation of NMR and GC/MS analysis. Differences in the observed triterpenoid fingerprints between mummy specimens suggest that more than one plant species served as the triterpenoid resin source. Analysis of the triterpenoid acids of ancient embalming resin samples in the form of their methyl- and trimethylsilyl esters is compared. In addition we show a simple way to differentiate between residues of mastic from its use as incense during embalming or from direct mastic application in the embalming resin. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Reduction of polyester resin shrinkage by means of epoxy resin

    International Nuclear Information System (INIS)

    Pietrzak, M.; Brzostowski, A.

    1981-01-01

    An attempt was made to decrease the shrinkage of unsaturated polyester resin, taking place during radiation-induced curing, by the addition of epoxy resin. In order to combine chemically both resins, the epoxy component was modified with cinnamic and acrylic acids. A composition of 90 parts of polyester resin, 10 parts of epoxy resin modified with cinnamic acid, and 150 parts of a silica filler showed a volume shrinkage of 1.2%. (author)

  1. Resin composite repair: Quantitative microleakage evaluation of resin-resin and resin-tooth interfaces with different surface treatments

    OpenAIRE

    Celik, Cigdem; Cehreli, Sevi Burcak; Arhun, Neslihan

    2015-01-01

    Objective: The aim was to evaluate the effect of different adhesive systems and surface treatments on the integrity of resin-resin and resin-tooth interfaces after partial removal of preexisting resin composites using quantitative image analysis for microleakage testing protocol. Materials and Methods: A total of 80 human molar teeth were restored with either of the resin composites (Filtek Z250/GrandioSO) occlusally. The teeth were thermocycled (1000?). Mesial and distal 1/3 parts of the res...

  2. Environmental effect of rapeseed oil ethyl ester

    International Nuclear Information System (INIS)

    Makareviciene, V.; Janulis, P.

    2003-01-01

    Exhaust emission tests were conducted on rapeseed oil methyl ester (RME), rapeseed oil ethyl ester (REE) and fossil diesel fuel as well as on their mixtures. Results showed that when considering emissions of nitrogen oxides (NO x ), carbon monoxide (CO) and smoke density, rapeseed oil ethyl ester had less negative effect on the environment in comparison with that of rapeseed oil methyl ester. When fuelled with rapeseed oil ethyl ester, the emissions of NO x showed an increase of 8.3% over those of fossil diesel fuel. When operated on 25-50% bio-ester mixed with fossil diesel fuel, NO x emissions marginally decreased. When fuelled with pure rapeseed oil ethyl ester, HC emissions decreased by 53%, CO emissions by 7.2% and smoke density 72.6% when compared with emissions when fossil diesel fuel was used. Carbon dioxide (CO 2 ) emissions, which cause greenhouse effect, decreased by 782.87 g/kWh when rapeseed oil ethyl ester was used and by 782.26 g/kWh when rapeseed oil methyl ester was used instead of fossil diesel fuel. Rapeseed oil ethyl ester was more rapidly biodegradable in aqua environment when compared with rapeseed oil methyl ester and especially with fossil diesel fuel. During a standard 21 day period, 97.7% of rapeseed oil methyl ester, 98% of rapeseed oil ethyl ester and only 61.3% of fossil diesel fuel were biologically decomposed. (author)

  3. Devices using resin wafers and applications thereof

    Science.gov (United States)

    Lin, YuPo J [Naperville, IL; Henry, Michael P [Batavia, IL; Snyder, Seth W [Lincolnwood, IL; Martin, Edward [Libertyville, IL; Arora, Michelle [Woodridge, IL; de la Garza, Linda [Woodridge, IL

    2009-03-24

    Devices incorporating a thin wafer of electrically and ionically conductive porous material made by the method of introducing a mixture of a thermoplastic binder and one or more of anion exchange moieties or cation exchange moieties or mixtures thereof and/or one or more of a protein capture resin and an electrically conductive material into a mold. The mixture is subjected to temperatures in the range of from about 60.degree. C. to about 170.degree. C. at pressures in the range of from about 0 to about 500 psig for a time in the range of from about 1 to about 240 minutes to form thin wafers. Devices include electrodeionization and separative bioreactors in the production of organic and amino acids, alcohols or esters for regenerating cofactors in enzymes and microbial cells.

  4. Synthesis of substituted 2-cyanoarylboronic esters

    DEFF Research Database (Denmark)

    Lysén, Morten; Hansen, Henriette M; Begtrup, Mikael

    2006-01-01

    The synthesis of substituted 2-cyanoarylboronic esters is described via lithiation/in situ trapping of the corresponding methoxy-, trifluoromethyl-, fluoro-, chloro-, and bromobenzonitriles. The crude arylboronic esters were obtained in high yields and purities and with good regioselectivities....

  5. Mechanical properties and chemical stability of pivalolactone-based poly(ether ester)s

    NARCIS (Netherlands)

    Tijsma, E.J.; Tijsma, E.J.; van der Does, L.; Bantjes, A.; Bantjes, A.; Vulic, I.

    1994-01-01

    The processing, mechanical and chemical properties of poly(ether ester)s, prepared from pivalolactone (PVL), 1,4-butanediol (4G) and dimethyl terephthalate (DMT), were studied. The poly(ether ester)s could easily be processed by injection moulding, owing to their favourable rheological and thermal

  6. Regioselective Synthesis of Cellulose Ester Homopolymers

    Science.gov (United States)

    Daiqiang Xu; Kristen Voiges; Thomas Elder; Petra Mischnick; Kevin J. Edgar

    2012-01-01

    Regioselective synthesis of cellulose esters is extremely difficult due to the small reactivity differences between cellulose hydroxyl groups, small differences in steric demand between acyl moieties of interest, and the difficulty of attaching and detaching many protecting groups in the presence of cellulose ester moieties without removing the ester groups. Yet the...

  7. Synthesis and characterization of an N-(2-hydroxyethyl)-ethylenediaminetriacetic acid resin

    International Nuclear Information System (INIS)

    Lai, Y.F.

    1977-10-01

    A chelating ion-exchange resin with N-(2-hydroxyethyl)ethylene-diaminetriacetic acid (HEDTA) used as the ligand chemically bonded to XAD-4 by an ester linkage, HEDTA-4, was synthesized. It is stable under normal experimental conditions with the liquid chromatograph. The structure of the resin was confirmed by an infrared spectrum, and by potentiometric titrations. The capacity of the resin was also obtained by potentiometric titration and by a nitrogen analysis. The resin was used to pack a column of 5 mm internal diameter and 5 cm long. The effect of pH on the retention of different metal ions on the resin was studied. It was found that the resin was most selective for chromium(III), copper(II), lead(II), mercury(II), uranium(VI), zirconium(IV) and zinc(II) at a pH of less than 3. Furthermore, the resin proves to be functioning with a chelating mechanism rather than ion-exchange, and it can concentrate trace metal ions in the presence of a large excess of calcium and magnesium. This makes the resin potentially useful for purifying and analyzing drinking water

  8. An Evaluation of Fracture Toughness of Vinyl Ester Composites Cured under Microwave Conditions

    Science.gov (United States)

    Ku, H.; Chan, W. L.; Trada, M.; Baddeley, D.

    2007-12-01

    The shrinkage of vinyl ester particulate composites has been reduced by curing the resins under microwave conditions. The reduction in the shrinkage of the resins by microwaves will enable the manufacture of large vinyl ester composite items possible (H.S. Ku, G. Van Erp, J.A.R. Ball, and S. Ayers, Shrinkage Reduction of Thermoset Fibre Composites during Hardening using Microwaves Irradiation for Curing, Proceedings, Second World Engineering Congress, Kuching, Malaysia, 2002a, 22-25 July, p 177-182; H.S. Ku, Risks Involved in Curing Vinyl Ester Resins Using Microwaves Irradiation. J. Mater. Synth. Proces. 2002b, 10(2), p 97-106; S.H. Ku, Curing Vinyl Ester Particle Reinforced Composites Using Microwaves. J. Comp. Mater., (2003a), 37(22), p 2027-2042; S.H. Ku and E. Siores, Shrinkage Reduction of Thermoset Matrix Particle Reinforced Composites During Hardening Using Microwaves Irradiation, Trans. Hong Kong Inst. Eng., 2004, 11(3), p 29-34). In tensile tests, the yield strengths of samples cured under microwave conditions obtained are within 5% of those obtained by ambient curing; it is also found that with 180 W microwave power, the tensile strengths obtained for all duration of exposure to microwaves are also within the 5% of those obtained by ambient curing. While, with 360 W microwave power, the tensile strengths obtained for all duration of exposure to microwaves are 5% higher than those obtained by ambient curing. Whereas, with 540 W microwave power, the tensile strengths obtained for most samples are 5% below those obtained by ambient curing (H. Ku, V.C. Puttgunta, and M. Trada, Young’s Modulus of Vinyl Ester Composites Cured by Microwave Irradiation: Preliminary Results, J. Electromagnet. Waves Appl., 2007, 20(14), p. 1911-1924). This project, using 33% by weight fly ash reinforced vinyl ester composite [VE/FLYSH (33%)], is to further investigate the difference in fracture toughness between microwave cured vinyl ester particulate composites and those cured

  9. Catalytic Ester to Stannane Functional Group Interconversion via Decarbonylative Cross-Coupling of Methyl Esters

    KAUST Repository

    Yue, Huifeng

    2018-01-03

    An unprecedented conversion of methyl esters to stannanes was realized, providing access to a series of arylstannanes via nickel catalysis. Various common esters including ethyl, cyclohexyl, benzyl, and phenyl esters can undergo the newly developed decarbonylative stannylation reaction. The reaction shows broad substrate scope, can differentiate between different types of esters, and if applied in consecutive fashion, allows the transformation of methyl esters into aryl fluorides or biaryls via fluororination or arylation.

  10. Method for removing contaminants from plastic resin

    Science.gov (United States)

    Bohnert, George W [Harrisonville, MO; Hand, Thomas E [Lee's Summit, MO; DeLaurentiis, Gary M [Jamestown, CA

    2008-12-09

    A resin recycling method that produces essentially contaminant-free synthetic resin material in an environmentally safe and economical manner. The method includes receiving the resin in container form. The containers are then ground into resin particles. The particles are exposed to a solvent, the solvent contacting the resin particles and substantially removing contaminants on the resin particles. After separating the particles and the resin, a solvent removing agent is used to remove any residual solvent remaining on the resin particles after separation.

  11. Calysolins I-IV, resin glycosides from Calystegia soldanella.

    Science.gov (United States)

    Takigawa, Ayako; Muto, Haruka; Kabata, Kiyotaka; Okawa, Masafumi; Kinjo, Junei; Yoshimitsu, Hitoshi; Nohara, Toshihiro; Ono, Masateru

    2011-11-28

    Four new resin glycosides having intramolecular cyclic ester structures (jalapins), named calysolins I-IV (1-4), were isolated from the methanol extract of leaves, stems, and roots of Calystegia soldanella , along with one known jalapin (5) derivative. The structures of 1-4 were determined on the basis of spectroscopic data and chemical evidence. They fall into two types, one having a 22-membered ring (1 and 4) and the other with a 27-membered ring (2 and 3). The sugar moieties of 1-4 were partially acylated by some organic acids. Compound 4 is the first example of a hexaglycoside of jalapin.

  12. Contact allergy to epoxy resin

    DEFF Research Database (Denmark)

    Bangsgaard, Nannie; Thyssen, Jacob Pontoppidan; Menné, Torkil

    2012-01-01

    to epoxy resin remained stable over the study period. Of the patients with an epoxy resin-positive patch test, 71% returned a questionnaire; 95 patients had worked with epoxy resin in the occupational setting, and, of these, one-third did not use protective gloves and only 50.5% (48) had participated...

  13. Highly efficient synthetic method onpyroacm resin using the boc SPPS protocol for C-terminal cysteine peptide synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Juvekar, Vinayak; Kim, Kang Tae; Gong, Young Dae [Innovative Drug Library Research Center, Dept. of Chemistry, College of Science, Dongguk University, Seoul (Korea, Republic of)

    2017-01-15

    A very effective process on Pyroacm resin was developed for solid-phase peptide synthesis (SPPS) of C-terminal cysteine and cysteine ester peptides. The process uses cysteine side chain anchoring to the Pyroacm resin and the Boc protocol for SPPS. The Pyroacm resin showed remarkable stability under standard trifluoromethanesulfonic acid (TFMSA) cleavage condition. TFMSA cleavage of protecting groups generates a peptide-linked resin, which can be subjected to peptide modification reactions. Finally, the peptide can be cleaved from the resin using methoxycarbonylsulfenyl chloride. The utility of this protocol was demonstrated by its applications to the synthesis of model peptides, key intermediates in the preparation of natural products riparin 1.2 and a-factor.

  14. Enhancement of adhesion between resin coating materials and resin cements.

    Science.gov (United States)

    Udo, Tomoaki; Nikaido, Toru; Ikeda, Masaomi; Weerasinghe, Dinesh S; Harada, Naoko; Foxton, Richard M; Tagami, Junji

    2007-07-01

    Resin coating technique is a unique method that improves the dentin bond strength of resin cements in indirect restorations. However, the weak link of a specimen bonded using the resin coating technique was reported to be the bonded interface between the resin coating material and resin cement. The purpose of this study, therefore, was to enhance the bonding performance between a resin coating material and a resin cement. Two light-cured flowable composites, Protect Liner F and Clearfil Flow FX, were used as coating materials, and two dual-cure composite materials, Panavia F 2.0 and Clearfil DC Core Automix, were used as resin cements. The ultimate tensile strength of each material and the microtensile bond strengths of the bonded specimens of resin coating material and resin cement were measured using a crosshead speed of 1.0 mm/min. Three-way ANOVA (p=0.05) revealed that the highest microtensile bond strength was obtained using a combination of Clearfil Flow FX and Clearfil DC Core Automix, and when the surface of the coating material was treated with ED Primer II. It was strongly suggested that materials with a higher ultimate tensile strength, when used in both resin coating and cementation, could enhance the bond strength between the two.

  15. Resin impregnation process for producing a resin-fiber composite

    Science.gov (United States)

    Palmer, Raymond J. (Inventor); Moore, William E. (Inventor)

    1994-01-01

    Process for vacuum impregnation of a dry fiber reinforcement with a curable resin to produce a resin-fiber composite, by drawing a vacuum to permit flow of curable liquid resin into and through a fiber reinforcement to impregnate same and curing the resin-impregnated fiber reinforcement at a sufficient temperature and pressure to effect final curing. Both vacuum and positive pressure, e.g. autoclave pressure, are applied to the dry fiber reinforcement prior to application of heat and prior to any resin flow to compact the dry fiber reinforcement, and produce a resin-fiber composite of reduced weight, thickness and resin content, and improved mechanical properties. Preferably both a vacuum and positive pressure, e.g. autoclave pressure, are also applied during final curing.

  16. Development of high radiation-resistant glass fiber reinforced plastics with cyanate-based resin for superconducting magnet systems

    Energy Technology Data Exchange (ETDEWEB)

    Idesaki, Akira, E-mail: idesaki.akira@qst.go.jp [Quantum Beam Science Directorate, Japan Atomic Energy Agency, Watanuki 1233, Takasaki, Gunma 370-1292 (Japan); Nakamoto, Tatsushi [Cryogenic Science Center, High Energy Accelerator Research Organization (KEK), 1-1 Oho, Tsukuba, Ibaraki 305-0801 (Japan); Yoshida, Makoto [Institute of Particle and Nuclear Studies, High Energy Accelerator Research Organization (KEK), 1-1 Oho, Tsukuba, Ibaraki 305-0801 (Japan); Shimada, Akihiko [Quantum Beam Science Directorate, Japan Atomic Energy Agency, Watanuki 1233, Takasaki, Gunma 370-1292 (Japan); Iio, Masami; Sasaki, Kenichi; Sugano, Michinaka [Cryogenic Science Center, High Energy Accelerator Research Organization (KEK), 1-1 Oho, Tsukuba, Ibaraki 305-0801 (Japan); Makida, Yasuhiro [Institute of Particle and Nuclear Studies, High Energy Accelerator Research Organization (KEK), 1-1 Oho, Tsukuba, Ibaraki 305-0801 (Japan); Ogitsu, Toru [Cryogenic Science Center, High Energy Accelerator Research Organization (KEK), 1-1 Oho, Tsukuba, Ibaraki 305-0801 (Japan)

    2016-11-15

    Highlights: • GFRPs for superconducting magnet systems were developed. • Cyanate-based resins were used for GFRPs as matrices. • Radiation resistance was evaluated based on gas evolution and mechanical properties. • GFRP with bismaleimide-triazine resin exhibited excellent radiation resistance. - Abstract: Glass fiber reinforced plastics (GFRPs) with cyanate ester resin/epoxy resin, bismaleimide resin/epoxy resin, and bismaleimide-triazine resin as matrices were developed for the superconducting magnet systems used in high intensity accelerators. The radiation resistance of these GFRPs was evaluated based on their gas evolution and changes in their mechanical properties after gamma-ray irradiation with dose of 100 MGy in vacuum at ambient temperature. After irradiation, a small amount of gas was evolved from all of the GFRPs, and a slight decrease in mechanical properties was observed compared with the conventional epoxy resin-GFRP, G10. Among the GFRPs, the smallest amount of gas (6 × 10{sup −5} mol/g) was evolved from the GFRP with the bismaleimide-triazine resin, which also retained more than 88% of its flexural strength after 100 MGy irradiation; this GFRP is thus considered the most promising material for superconducting magnet systems.

  17. Multifunctional properties of multi-wall carbon nanotubes/cyanate-ester nanocomposites and CFRPs

    Science.gov (United States)

    Baltopoulos, A.; Fiamegkou, E.; Vavouliotis, A.; Karapappas, P.; Athanasopoulos, N.; Fotiou, I.; Kostopoulos, V.; Maagt, P. D.; Rohr, T.

    2009-07-01

    The incorporation of multi-wall carbon nanotubes at weight fractions of 0.5% wt. and 1% wt. in a PRIMASET cyanate ester system (PT-30) was examined. The thermo-mechanical and electrical properties of the developed nanopolymers were investigated and were compared with the neat matrix properties. A preparation method was developed for the incorporation of the fillers in the resin system. The phenomenon of re-agglomeration of nanotubes took place in the first stages of curing schedule but nevertheless according to the SEM images a good dispersion was generally achieved. DSC, DMA, TGA and thermal conductivity tests were performed for the thermal characterization. For the electrical characterization, AC and DC measurements took place. No significant change in the glass transition temperature (Tg), thermal conductivity and mass loss values was observed in comparison with the neat resin systems. However, in both cases the improvement of electrical conductivity was about nine orders of magnitude, indicating that percolation had been achieved. The elastic modulus in bending was examined and a slight increase was observed in direct comparison with the neat resin. Finally, the developed doped nanopolymer was used as matrix for the CFRPs manufacturing. A full manufacturing protocol was developed in order to overcome the challenging issues concerning the cyanate esters' handling and manufacturing processes. Moreover AC and DC measurements were performed along with thermal conductivity measurements and TMA. The produced modified composites were tested for short beam strength.

  18. Production of novel "functional oil" rich in diglycerides and phytosterol esters with "one-pot" enzymatic transesterification.

    Science.gov (United States)

    Zheng, Ming-Ming; Huang, Qing; Huang, Feng-Hong; Guo, Ping-Mei; Xiang, Xia; Deng, Qian-Chun; Li, Wen-Lin; Wan, Chu-Yun; Zheng, Chang

    2014-06-04

    Diglycerides and phytosterol esters are two important functional lipids. Phytosterol esters mixed with dietary diglyceride could not only influence body weight but also prevent or reverse insulin resistance and hyperlipidemia. In this study, a kind of novel "functional oil" rich in both diglycerides and phytosterol esters was prepared with "one-pot" enzymatic transesterification. First, lipase AYS (Candida rugosa) was immobilized on the porous cross-linked polystyrene resin beads (NKA) via hydrophobic interaction. The resulting immobilized AYS showed much better transesterification activity and thermal stability to freeways. On the basis of the excellent biocatalyst prepared, a method for high-efficiency enzymatic esterification of phytosterols with different triglycerides to produce corresponding functional oils rich in both diglycerides and phytosterol esters was developed. Four functional oils rich in both diglycerides and phytosterol esters with conversions >92.1% and controllable fatty acid composition were obtained under the optimized conditions: 80 mmol/L phytosterols, 160 mmol/L triglycerides, and 25 mg/mL AYS@NKA at 180 rpm and 50 °C for 12 h in hexane. The prepared functional oil possessed low acid value (≤1.0 mgKOH/g), peroxide value (≤2.1 mmol/kg), and conjugated diene value (≤1.96 mmol/kg) and high diglyceride and phytosterol ester contents (≥10.4 and ≥20.2%, respectively). All of the characteristics favored the wide application of the functional oil in different fields of functional food.

  19. Ester Tuiksoo. Proua Suhkru kibedad päevad / Ester Tuiksoo ; interv. Piret Tali

    Index Scriptorium Estoniae

    Tuiksoo, Ester, 1965-

    2005-01-01

    Põllumajandusminister Ester Tuiksoo, kellel peagi täitub ministri ametis aasta Euroopa Liidu suhkrutrahvist, maaettevõtlusest, põllumajandusest, Euroopa Liidu toetustest, ministri elu- ja teenistuskäigust. Lisa: Ester Tuiksoo

  20. Steroidal esters from Ferula sinkiangensis.

    Science.gov (United States)

    Li, Guangzhi; Li, Xiaojin; Cao, Li; Shen, Liangang; Zhu, Jun; Zhang, Jing; Wang, Junchi; Zhang, Lijing; Si, Jianyong

    2014-09-01

    Two new steroidal esters with an unusual framework, Sinkiangenorin A and B, a new organic acid glycoside, Sinkiangenorin C, and four known lignin compounds were isolated from the seeds of Ferula sinkiangensis. The structures of these compounds were established by spectroscopic analysis and single-crystal X-ray diffraction. All of the isolated compounds were tested against Hela, K562 and AGS human cancer cell lines. Sinkiangenorin C showed cytotoxic activity against AGS cells with an IC50 of 36.9 μM. Copyright © 2014 Elsevier B.V. All rights reserved.

  1. Flame Retardant Epoxy Resins

    Science.gov (United States)

    Thompson, C. M.; Smith, J. G., Jr.; Connell, J. W.; Hergenrother, P. M.; Lyon, R. E.

    2004-01-01

    As part of a program to develop fire resistant exterior composite structures for future subsonic commercial aircraft, flame retardant epoxy resins are under investigation. Epoxies and their curing agents (aromatic diamines) containing phosphorus were synthesized and used to prepare epoxy formulations. Phosphorus was incorporated within the backbone of the epoxy resin and not used as an additive. The resulting cured epoxies were characterized by thermogravimetric analysis, propane torch test, elemental analysis and microscale combustion calorimetry. Several formulations showed excellent flame retardation with phosphorous contents as low as 1.5% by weight. The fracture toughness of plaques of several cured formulations was determined on single-edge notched bend specimens. The chemistry and properties of these new epoxy formulations are discussed.

  2. Bismaleimide Copolymer Matrix Resins

    Science.gov (United States)

    Parker, John A.; Heimbuch, Alvin H.; Hsu, Ming-Ta S.; Chen, Timothy S.

    1987-01-01

    Graphite composites, prepared from 1:1 copolymer of two new bismaleimides based on N,N'-m-phenylene-bis(m-amino-benzamide) structure have mechanical properties superior to those prepared from other bismaleimide-type resins. New heat-resistant composites replace metal in some structural applications. Monomers used to form copolymers with superior mechanical properties prepared by reaction of MMAB with maleic or citraconic anhydride.

  3. System for removing contaminants from plastic resin

    Science.gov (United States)

    Bohnert, George W.; Hand, Thomas E.; DeLaurentiis, Gary M.

    2010-11-23

    A resin recycling system that produces essentially contaminant-free synthetic resin material in an environmentally safe and economical manner. The system includes receiving the resin in container form. A grinder grinds the containers into resin particles. The particles are exposed to a solvent in one or more solvent wash vessels, the solvent contacting the resin particles and substantially removing contaminants on the resin particles. A separator is used to separate the resin particles and the solvent. The resin particles are then placed in solvent removing element where they are exposed to a solvent removing agent which removes any residual solvent remaining on the resin particles after separation.

  4. Batatins III-VI, glycolipid ester-type dimers from Ipomoea batatas.

    Science.gov (United States)

    Rosas-Ramírez, Daniel; Escalante-Sánchez, Edgar; Pereda-Miranda, Rogelio

    2011-06-01

    Batatins III-VI (1-4), glycolipid ester-type dimers, were isolated from the tuberous roots of sweet potato (Ipomoea batatas) using recycle high performance liquid chromatography. Their structures were characterized by means of several high-resolution NMR and mass spectrometry techniques. These compounds are the first examples of ester-type dimers which consist of two units of the heterotetrasaccharide operculinic acid C. Each unit was esterified by a different amount and type of acid residues: (2S)-methylbutanoic, cinnamic, decanoic (capric) and dodecanoic (lauric) acids. Batatins III-VI (1-4) are an example of the presence of a large number of resin glycoside congeners in each morning glory species caused by partial acylation of their constitutive saccharide cores. Copyright © 2011 Elsevier Ltd. All rights reserved.

  5. Analysis in vitro of direct bonding system with cyanoacrylate ester and orthodontic wires.

    Science.gov (United States)

    Manfrin, Thais Mara; Poi, Wilson Roberto; de Mendonça, Marcos Rogério; Cardoso, Leandro Carvalho; Massa Sundefeld, Maria Lúcia Marçal; Sonoda, Celso Koogi; Panzarini, Sônia Regina

    2009-04-01

    The aim of this study was to evaluate the tensile strength of orthodontic wires bonded onto the enamel with cyanoacrylate ester. To obtain the specimens, 120 human premolars (extracted for orthodontic or periodontal reasons) were included in acrylic blocks of rapid polymerization with three teeth each. Four groups were formed with ten specimens each. In the specimens, a dental splint model was made with cyanoacrylate ester and round stainless steel wire. In groups I, II and III, cyanoacrylate ester was used with round steel wires, with variation in diameter: 0.014 inches; 0.016 inches and 0.018 inches, respectively. In group IV, round steel wire 0.018 inches was used with photo polymerizing resin composite with previous acid etching. The adhesive force of the materials was measured in two points under the action of the tensiometer (ETM-USA). The number of loose wires was counted along with those that remained fixed according to the different levels of force applied because of the direction of the tensile force (vertical or horizontal) and the diameter of the wire used. The data obtained were first submitted to a descriptive analysis and then submitted to a statistical analysis (Friedman's Test and Dunn's Test of Multiple Comparison - Epi-info 3.2). Within the limitations of the experimental conditions presented, the cyanoacrylate ester or 'Super Bonder' maintained bonded to enamel and steel wires (0.016 and 0.018 inches) during the tensile strength tests under different levels of applied forces.

  6. Biokompatibilitas Gelas Ionomer Modifikasi Resin

    OpenAIRE

    Rotua Lestari M

    2008-01-01

    Saat ini banyak berkembang material baru dalam dunia kedokteran gigi diantaranya adalah Gelas ionomer modifikasi resin yang dikembangkan untuk mengatasi kekurangan-kekurangan dari gelas ionomer konvensional. Adanya penambahan monomer resin daIam bentuk 2-hydroxyethylmetacylate (HEMA) telah meningkatkan kekuatan dari bahan ini. Gelas ionomer modifikasi resin mempunyai sifat-sifat fisis dan mekanis yang lebih baik dibandingkan dengan gelas ionomer konvensional. Gelas ionomer modifikasi ...

  7. Preparation of Spirocyclic β-Proline Esters

    DEFF Research Database (Denmark)

    Fjelbye, Kasper; Marigo, Mauro; Clausen, Rasmus Prætorius

    2017-01-01

    A series of novel N-Bn-protected spirocyclic β-proline esters were prepared using [3+2] cycloaddition and subsequently converted into their corresponding aldehydes. In addition, two novel N-Cbz-protected spirocyclic β-proline esters were prepared using intramolecular cyclization starting from sim...

  8. Anticholinesterase activity of fluorochloronitroacetic acid esters

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, Yu.Ya.; Brel, V.K. Martynov, I.V.

    1984-11-01

    Results are presented from pharmacologic and biochemical experiments leading to the conclusion that fluorochloronitroacetic acid esters have anticholinesterase activity. Since the esters caused muscular weakness in mice, experiments were performed on isolated tissue preparation. The biochemical experiments consisted of finding the biomolecular constants of irreversible inhibition of acetylcholinesterase by the esters, using acetylcholinesterase from human erythrocytes, as well as horse serum cholinesterase. The ethyl and n-propyl esters of halogen nitroacetic acid were used in all experiments. It was found that the propyl ester caused an increase in the force of individual contractions in the isolated muscle specimens, plus an inability of the muscle to retain tetanus. The substances were determined to have an anticholinesterase effect. The mechanism of cholinesterase inhibition is not yet known. It is probable that the substances acylate the serine hydroxyl of the esterase center of the cholinestersase. 7 references, 1 figure.

  9. Hyperbranched polysiloxane functionalized graphene oxide for dicyclopentadiene bisphenol dicyanate ester nanocomposites with high performance

    Directory of Open Access Journals (Sweden)

    H. X. Yan

    2014-06-01

    Full Text Available We report an efficient and novel method to functionalize graphene oxide (GO with hyperbranched polysiloxane and successfully compound them with dicyclopentadiene bisphenol dicyanate ester (DCPDCE to prepare nanocomposites. X-ray photoelectron spectroscopy (XPS and Fourier-transform infrared spectra (FT-IR were employed to examine the surface functionalization of GO. The effects of functionalized GO on the curing reaction, mechanical, dielectric and thermal properties of DCPDCE resin were investigated systematically. Results of DSC show that the addition of modified GO can facilitate the curing reaction of DCPDCE and decrease the curing temperature of DCPDCE. Compared with pure DCPDCE resin, the impact and flexural strengths of the nanocomposite materials are improved markedly with up to 66 and 50% increasing magnitude, respectively. Meanwhile, the modified GO/DCPDCE systems exhibit lower dielectric constant and loss than pure DCPDCE resin over the testing frequency from 10 to 60 MHz. In addition, the thermal stability and moisture resistance of modified GO/DCPDCE nanocomposties are also superior to that of pure DCPDCE resin.

  10. Process study of polycyanate resin for wet-filament wound high-strength composites

    Energy Technology Data Exchange (ETDEWEB)

    Frame, B.J.

    1997-12-31

    Polycyanate (or cyanate ester) resins offer advantages as composite matrices because of their high thermal stability, low outgassing, low water absorption and radiation resistance. This report describes the results of a processing study to develop high-strength hoop-wound composite by the wet-filament winding method using Toray T1000G carbon fiber and YLA RS-14 polycyanate resin as the constituent materials. T1000G/RS-14 composite cylinders were wet-wound and cured using different process schedules and then evaluated for hoop tensile strength and modulus, transverse flexural strength and short beam shear strength. The results of material characterization tests performed on the T1000G carbon fiber and RS-14 resin constituents used in this study are also presented.

  11. Evaluation and improvement of gamma-ray stability of chelating resins containing oxy-acid groups of phosphorus

    International Nuclear Information System (INIS)

    Jyo, Akinori; Yamabe, Kazunori; Shuto, Taketomi

    1998-01-01

    Chelating resins containing oxy-acid groups of phosphorus, such as phosphonic and phosphoric acid groups have been studied from the point of view of solvent extraction processes for the separation of nuclear fuel elements as well as of fission product ones. The present work was planned to evaluate the effect of gamma-ray on properties of the resins and to obtain directional information for design of the resins having high stability to gamma-ray. It was clarified that gamma-ray stability of the resins is not high; tolerance limit is ca. 2.3x10 3 C/kg. The present work also clarified that polymers crosslinked with divinylbenzene have much higher gamma-ray stability than ones crosslinked with dimetacrylate esters of oligo (ethylene glycol)s. (J.P.N.)

  12. Properties of the Carboxylate ion exchange resins

    International Nuclear Information System (INIS)

    Allard, Bert; Dario, Maarten; Boren, Hans; Torstenfelt, Boerje; Puigdomenech, Ignasi; Johansson, Claes

    2002-09-01

    Weakly acidic, carboxylic resin has been selected, together with strong base anion resins, for water purification at the Forsmark 1 and 2 reactors. For the strong (but not the weak) ion exchange resin the Nuclear Power Inspectorate has given permission to dispose the spent resins in the SFR 1 (the Final Repository for Radioactive Operational Waste). This report gives a review of the carboxylic resins and comes to the conclusion that the resins are very stable and that there should not exist any risks for increased leaching of radionuclides from SFR 1 if these resins are disposed (compared to the strong resins)

  13. [Acrylic resin removable partial dentures

    NARCIS (Netherlands)

    Baat, C. de; Witter, D.J.; Creugers, N.H.J.

    2011-01-01

    An acrylic resin removable partial denture is distinguished from other types of removable partial dentures by an all-acrylic resin base which is, in principle, solely supported by the edentulous regions of the tooth arch and in the maxilla also by the hard palate. When compared to the other types of

  14. Cure shrinkage in casting resins

    Energy Technology Data Exchange (ETDEWEB)

    Spencer, J. Brock [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-02-01

    A method is described whereby the shrinkage of a casting resin can be determined. Values for the shrinkage of several resin systems in frequent use by Sandia have been measured. A discussion of possible methods for determining the stresses generated by cure shrinkage and thermal contraction is also included.

  15. Synthesis of Trimethylolpropane Esters of Calophyllum Methyl Esters : Effect of Temperature and Molar Ratio

    Directory of Open Access Journals (Sweden)

    Yeti Widyawati

    2014-12-01

    Full Text Available Trimethylolpropane esters were synthesized by transesterification of calophyllum methyl esters and trimethylolpropane using a calcium oxide as the catalyst. The results showed that the optimal reaction conditions (temperature: 130 0C, reaction time: 5 h, reactant molar ratio: 3.9:1, catalyst amount 3%w/w, and formed  trimethylolpropane ester of 79.0% were obtained. The basic physicochemical properties of the trimethylolpropane esters were the following : kinematic viscosities of 56.40 cSt and 8.8 cSt at 40 0C and 100 0C,  viscosity index 193, flash point 218 0C and pour point -3 0C. So Methyl esters of fatty acids of would callophylum  methyl ester is good raw material for the synthesis of lubricating oils.

  16. Cobalt-catalyzed hydrogenation of esters to alcohols: unexpected reactivity trend indicates ester enolate intermediacy.

    Science.gov (United States)

    Srimani, Dipankar; Mukherjee, Arup; Goldberg, Alexander F G; Leitus, Gregory; Diskin-Posner, Yael; Shimon, Linda J W; Ben David, Yehoshoa; Milstein, David

    2015-10-12

    The atom-efficient and environmentally benign catalytic hydrogenation of carboxylic acid esters to alcohols has been accomplished in recent years mainly with precious-metal-based catalysts, with few exceptions. Presented here is the first cobalt-catalyzed hydrogenation of esters to the corresponding alcohols. Unexpectedly, the evidence indicates the unprecedented involvement of ester enolate intermediates. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. 21 CFR 172.854 - Polyglycerol esters of fatty acids.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polyglycerol esters of fatty acids. 172.854 Section... HUMAN CONSUMPTION Multipurpose Additives § 172.854 Polyglycerol esters of fatty acids. Polyglycerol esters of fatty acids, up to and including the decaglycerol esters, may be safely used in food in...

  18. Pharmacokinetics of Ketorolac Pentyl Ester, a Novel Ester Derivative of Ketorolac, in Rabbits

    Directory of Open Access Journals (Sweden)

    Jann-Inn Tzeng

    2005-08-01

    Full Text Available Ketorolac is a potent nonsteroidal anti-inflammatory drug. Recently, a novel ester of ketorolac, ketorolac pentyl ester, was synthesized. When prepared in injectable oil, the new agent demonstrated a long duration of action. Ketorolac pentyl ester was synthesized using a prodrug design by esterification of ketorolac, and appeared to be a prodrug of ketorolac in vivo, which needed to be confirmed. The aim of the present study was to establish the prodrug's pharmacokinetics in vivo, and to confirm whether or not ketorolac pentyl ester was a prodrug of ketorolac. Pharmacokinetic profiles of intravenous ketorolac and its pentyl ester on an equal-molar basis in six rabbits were evaluated. A high-performance liquid chromatographic method was used to determine the plasma concentrations of ketorolac and its pentyl ester. We found that the plasma concentrations of ketorolac pentyl ester declined rapidly after injection and so did the conversion of ketorolac pentyl ester to ketorolac. Also, the conversion of ketorolac was proved complete when compared with intravenous ketorolac under an equi-molar basis. In conclusion, this in vivo pharmacokinetic study confirmed that keterolac pentyl ester was a prodrug of keterolac.

  19. [Acrylic resin removable partial dentures].

    Science.gov (United States)

    de Baat, C; Witter, D J; Creugers, N H J

    2011-01-01

    An acrylic resin removable partial denture is distinguished from other types of removable partial dentures by an all-acrylic resin base which is, in principle, solely supported by the edentulous regions of the tooth arch and in the maxilla also by the hard palate. When compared to the other types of removable partial dentures, the acrylic resin removable partial denture has 3 favourable aspects: the economic aspect, its aesthetic quality and the ease with which it can be extended and adjusted. Disadvantages are an increased risk of caries developing, gingivitis, periodontal disease, denture stomatitis, alveolar bone reduction, tooth migration, triggering of the gag reflex and damage to the acrylic resin base. Present-day indications are ofa temporary or palliative nature or are motivated by economic factors. Special varieties of the acrylic resin removable partial denture are the spoon denture, the flexible denture fabricated of non-rigid acrylic resin, and the two-piece sectional denture. Furthermore, acrylic resin removable partial dentures can be supplied with clasps or reinforced by fibers or metal wires.

  20. Structural identification and biological activity of six new Shellolic esters from Lac.

    Science.gov (United States)

    Lu, Jin; Shang, Lei; Wen, Huimin; Huang, Jian; Li, Guoyu; Wang, Jinhui

    2018-03-01

    Six new sesquiterpenoid esters, named Shellolic ester A-F (1-6), along with four known Lac dyes (7-10) were isolated from methanol extract of the secretions of Laccifer lacca. Their structures were established on the basis of spectroscopic analyses (IR, HR-ESI-MS, 1D and 2D NMR) and by comparison with published data. Biological activities evaluation of the isolates showed that they were inactive against human cancer cell lines (HepG2, MCF-7, Hela and C6) and LPS-treated RAW264.7, which is well consistent with that Lac resin used as nontoxic material in agriculture applications, pharmaceutical formulations, and food additives. However, compound 2, 4, 7, 9, 10 were found to be considerable active against B. subtilis, E. coli, and S. aureus microorganisms. The results complements the current knowledge about Lac produced from China. Meanwhile, Our present study further reveals that Lac resin are edible with no toxicity and physiologically harmless at the level employed as an excipient. Copyright © 2017. Published by Elsevier B.V.

  1. Tensile mechanical behavior and fracture toughness of MWCNT and DWCNT modified vinyl-ester/polyester hybrid nanocomposites produced by 3-roll milling

    OpenAIRE

    Seyhan, Abdullah Tuğrul; Tanoğlu, Metin; Schulte, Karl

    2009-01-01

    This study aims to investigate the tensile mechanical behavior and fracture toughness of vinyl-ester/polyester hybrid nanocomposites containing various types of nanofillers, including multi- and double-walled carbon nanotubes with and without amine functional groups (MWCNTs, DWCNTs, MWCNT-NH2 and DWCNT-NH2). To prepare the resin suspensions, very low contents (0.05, 0.1 and 0.3 wt.%) of carbon nanotubes (CNTs) were dispersed within a specially synthesized styrene-free polyester resin, conduct...

  2. Conversion of carbohydrates to levulinic acid esters

    DEFF Research Database (Denmark)

    2014-01-01

    The present invention relates to the field of converting carbohydrates into levulinic acid, a platform chemical for many chemical end products. More specifically the invention relates to a method for converting carbohydrates such as mono-, di- or polysaccharides, obtained from for example biomass...... production into a suitable levulinic acid ester in the presence of a zeolite or zeotype catalyst and a suitable alcohol, and the ester may be further converted into levulinic acid if desired....

  3. Chromatography resin support

    Science.gov (United States)

    Dobos, James G.

    2002-01-01

    An apparatus and method of using an improved chromatography resin support is disclosed. The chromatography support platform is provided by a stainless steel hollow cylinder adapted for being inserted into a chromatography column. An exterior wall of the stainless steel cylinder defines a groove for carrying therein an "O"-ring. The upper surface of the stainless steel column is covered by a fine stainless steel mesh welded to the edges of the stainless steel cylinder. When placed upon a receiving ledge defined within a chromatography column, the "O"-ring provides a fluid tight seal with the inner edge wall of the chromatography cylinder. The stainless steel mesh supports the chromatography matrix and provides a back flushable support which is economical and simple to construct.

  4. 21 CFR 872.3140 - Resin applicator.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Resin applicator. 872.3140 Section 872.3140 Food... DEVICES DENTAL DEVICES Prosthetic Devices § 872.3140 Resin applicator. (a) Identification. A resin applicator is a brushlike device intended for use in spreading dental resin on a tooth during application of...

  5. Allenyl esters as quenching agents for ruthenium olefin metathesis catalysts.

    Science.gov (United States)

    Roy, Animesh; Silvestri, Maximilian A; Hall, Robert A; Lepore, Salvatore D

    2017-01-04

    In the attempt to synthesize substituted allenyl esters through a metathesis coupling of unsubstituted allenyl esters and alkenes using a variety of ruthenium catalysts, it was discovered that allenyl esters themselves cleanly arrested the activity of the catalysts. Further studies suggests possible utility of allene esters as general quenching agents for metathesis reactions. To explore this idea, several representative olefin metathesis reactions, including ring closing, were successfully terminated by the addition of simple allenyl esters for more convenient purification.

  6. Bulk-Fill Resin Composites

    DEFF Research Database (Denmark)

    Benetti, Ana Raquel; Havndrup-Pedersen, Cæcilie; Honoré, Daniel

    2015-01-01

    the restorative procedure. The aim of this study, therefore, was to compare the depth of cure, polymerization contraction, and gap formation in bulk-fill resin composites with those of a conventional resin composite. To achieve this, the depth of cure was assessed in accordance with the International Organization...... for Standardization 4049 standard, and the polymerization contraction was determined using the bonded-disc method. The gap formation was measured at the dentin margin of Class II cavities. Five bulk-fill resin composites were investigated: two high-viscosity (Tetric EvoCeram Bulk Fill, SonicFill) and three low......-viscosity (x-tra base, Venus Bulk Fill, SDR) materials. Compared with the conventional resin composite, the high-viscosity bulk-fill materials exhibited only a small increase (but significant for Tetric EvoCeram Bulk Fill) in depth of cure and polymerization contraction, whereas the low-viscosity bulk...

  7. and phenol–formaldehyde resin

    Indian Academy of Sciences (India)

    formaldehyde resin (PFR) modified with tetraethylorthosilicate are investigated in detail. The chemical synthesis of PFR, its modification with nanometer- sized SiO2 particles created by sol–gel method and subsequent coating, enables a preparation of ...

  8. Bending characteristics of resin concretes

    Directory of Open Access Journals (Sweden)

    Ribeiro Maria Cristina Santos

    2003-01-01

    Full Text Available In this research work the influence of composition and curing conditions in bending strength of polyester and epoxy concrete is analyzed. Various mixtures of resin and aggregates were considered in view of an optimal combination. The Taguchi methodology was applied in order to reduce the number of tests, and in order to evaluate the influence of various parameters in concrete properties. This methodology is very useful for the planning of experiments. Test results, analyzed by this methodology, shown that the most significant factors affecting bending strength properties of resin concretes are the type of resin, resin content and charge content. An optimal formulation leading to a maximum bending strength was achieved in terms of material parameters.

  9. Use of Anion Exchange Resins for One-Step Processing of Algae from Harvest to Biofuel

    Directory of Open Access Journals (Sweden)

    Martin Poenie

    2012-07-01

    Full Text Available Some microalgae are particularly attractive as a renewable feedstock for biodiesel production due to their rapid growth, high content of triacylglycerols, and ability to be grown on non-arable land. Unfortunately, obtaining oil from algae is currently cost prohibitive in part due to the need to pump and process large volumes of dilute algal suspensions. In an effort to circumvent this problem, we have explored the use of anion exchange resins for simplifying the processing of algae to biofuel. Anion exchange resins can bind and accumulate the algal cells out of suspension to form a dewatered concentrate. Treatment of the resin-bound algae with sulfuric acid/methanol elutes the algae and regenerates the resin while converting algal lipids to biodiesel. Hydrophobic polymers can remove biodiesel from the sulfuric acid/methanol, allowing the transesterification reagent to be reused. We show that in situ transesterification of algal lipids can efficiently convert algal lipids to fatty acid methyl esters while allowing the resin and transesterification reagent to be recycled numerous times without loss of effectiveness.

  10. Resin glycosides from Porana duclouxii.

    Science.gov (United States)

    Ding, Wen-Bing; Zhang, Dai-Gui; Liu, Chun-Jie; Li, Guan-Hua; Li, You-Zhi

    2014-01-01

    A new intact resin glycoside (3) and two glycosidic acids (1 and 2), all having a common trisaccharide moiety and (11S)-hydroxytetradecanoic acid or (3S,11S)-dihydroxytetradecanoic acid as the aglycone, were obtained from the roots of Porana duclouxii. Their structures were elucidated by spectroscopic analyses and chemical correlations. These compounds represent the first examples of resin glycosides from the genus Porana.

  11. Karakteristik Komposit Resin Berkemampuan Mengalir

    Directory of Open Access Journals (Sweden)

    Bambang Irawan

    2015-10-01

    Full Text Available The use of resin composites as posterior restoratives has markedly increased over the past decade. The patients demand for better esthetics, concerns related to possible mercury toxicity from amalgam and improvements in resin composite materials have significantly contributed the popularity of these materials. Early problems related to composites included excessive wear, less of anatomic form, post operative sensitivity, secondary caries and marginal leakage. Marginal adaptation still remains an unavoidable problem for composite restoration, especially at the gingival wall of cervical or Class II restoration. In an attempt to improve marginal sealing, many techniques and lining materials have been designed. To reduce stress generated by polymerization shrinkage, applying and curing of resin composites in layers is often recommended. Using a thick adhesive layer or low-viscosity resin may, due to its elastic properties, serve as a flexible intermediate layer and compensate for the polymerization stress created in resin composite. Flowable composites were created by retaining the same small particle size of traditional hybrid composite but reducing the filler content and allowing the increased resin to reduce the viscosity of the mixture. Flowable composites were introduced in 1996 as liners, fissure sealants and also in tunnel preparations. They have been suggested for Class I, II, III and V cavity restorations, preventive resin restorations and composite, porcelain and amalgam repairing. Their usage as a liner under high filled resins in posterior restorations has been shown to improve the adaptation of composites and effectively achieve clinically acceptable results. This article attempts to give a broad characteristics of different types of flowable composites. 

  12. Liquid monobenzoxazine based resin system

    Science.gov (United States)

    Tietze, Roger; Nguyen, Yen-Loan; Bryant, Mark

    2014-10-07

    The present invention provides a liquid resin system including a liquid monobenzoxazine monomer and a non-glycidyl epoxy compound, wherein the weight ratio of the monobenzoxazine monomer to the non-glycidyl epoxy compound is in a range of about 25:75 to about 60:40. The liquid resin system exhibits a low viscosity and exceptional stability over an extended period of time making its use in a variety of composite manufacturing methods highly advantageous.

  13. Methyl esters from vegetable oils with hydroxy fatty acids: Comparison of lesquerella and castor methyl esters

    Science.gov (United States)

    The search for alternative feedstocks for biodiesel as partial replacement for petrodiesel has recently extended to castor oil. In this work, the castor oil methyl esters were prepared and their properties determined in comparison to the methyl esters of lesquerella oil, which in turn is seen as alt...

  14. Characteristics of resin floc dispersion of anion and cation exchange resin in precoat filter using powdered ion exchange resin

    Energy Technology Data Exchange (ETDEWEB)

    Adachi, Tetsurou (Nitto Denko Corp., Ibaraki, Osaka (Japan)); Sawa, Toshio; Shindoh, Toshikazu

    1989-09-01

    The filtration performance of mixed filter aid consisting of powdered anion and cation exchange resins used in the precoat filter is closely related to the characteristics of resin floc dispersion. The factors related to resin floc dispersion of anion and cation exchange resin were investigated by measuring the specific settle volume of resin floc as an evaluating index in addition to the measurement of physical, chemical and electrochemical properties of powdered ion exchange resin. The effect of adsorption of iron oxide and polymer electrolyte and of ion exchange were determined. In addition, considered floc dispersion with adsorbing iron oxide, it was assumed that the amount and filling ratio of resin floc were related to summation and multiplication of surface electric charge respectively. An experimental expression was obtained for simulation of the change of specific settle volume of resin floc by particle size, surface area, ion exchange capacity and degree of ionization of the powdered ion exchange resin. (author).

  15. Characteristics of resin floc dispersion of anion and cation exchange resin in precoat filter using powdered ion exchange resin

    International Nuclear Information System (INIS)

    Adachi, Tetsurou; Sawa, Toshio; Shindoh, Toshikazu.

    1989-01-01

    The filtration performance of mixed filter aid consisting of powdered anion and cation exchange resins used in the precoat filter is closely related to the characteristics of resin floc dispersion. The factors related to resin floc dispersion of anion and cation exchange resin were investigated by measuring the specific settle volume of resin floc as an evaluating index in addition to the measurement of physical, chemical and electrochemical properties of powdered ion exchange resin. The effect of adsorption of iron oxide and polymer electrolyte and of ion exchange were determined. In addition, considered floc dispersion with adsorbing iron oxide, it was assumed that the amount and filling ratio of resin floc were related to summation and multiplication of surface electric charge respectively. An experimental expression was obtained for simulation of the change of specific settle volume of resin floc by particle size, surface area, ion exchange capacity and degree of ionization of the powdered ion exchange resin. (author)

  16. Silane Reduction of 5-Hydroxy-6-methyl-pyridine-3,4-dicarboxylic Acid Diethyl Ester: Synthesis of Vitamin B6

    Directory of Open Access Journals (Sweden)

    Andrew G. Gum

    2003-12-01

    Full Text Available Alternative methods for the synthesis of pyridoxine have been investigated. The key intermediate, 5-hydroxy-6-methyl-pyridine-3,4-dicarboxylic acid diethyl ester (5, was reduced with either a silane monomer (MeSiH(OEt2 or a polysiloxane (polymethylhydrosiloxane, PMHS to afford crude pyridoxine. An isolation technique utilizing a commercially available resin was devised, affording the desired product, vitamin B6, in an overall yield of 38-54 % and a purity of 76%.

  17. Synthesis of biodiesel from pongamia oil using heterogeneous ion-exchange resin catalyst.

    Science.gov (United States)

    Jaya, N; Selvan, B Karpanai; Vennison, S John

    2015-11-01

    Biodiesel is a clean-burning renewable substitute fuel for petroleum. Biodiesel could be effectively produced by transesterification reaction of triglycerides of vegetable oils with short-chain alcohols in the presence of homogeneous or heterogeneous catalysts. Conventionally, biodiesel manufacturing processes employ strong acids or bases as catalysts. But, separation of the catalyst and the by-product glycerol from the product ester is too expensive to justify the product use as an automobile fuel. Hence heterogeneous catalysts are preferred. In this study, transesterification of pongamia oil with ethanol was performed using a solid ion-exchange resin catalyst. It is a macro porous strongly basic anion exchange resin. The process parameters affecting the ethyl ester yield were investigated. The reaction conditions were optimized for the maximum yield of fatty acid ethyl ester (FAEE) of pongamia oil. The properties of FAEE were compared with accepted standards of biodiesel. Engine performance was also studied with pongamia oil diesel blend and engine emission characteristics were observed. Copyright © 2015 Elsevier Inc. All rights reserved.

  18. Solid-phase peptide synthesis of endothelin receptor antagonists on novel flexible, styrene-acryloyloxyhydroxypropyl methacrylate-tripropyleneglycol diacrylate [SAT] resin.

    Science.gov (United States)

    Siyad, M A; Nair, Arun S V; Kumar, G S Vinod

    2010-03-08

    Novel cross-linked polymeric support by the copolymerization of styrene and 3-(acryloyloxy)-2-hydroxypropyl methacrylate with Tri(propyleneglycol) diacryalte (SAT) for solid-phase peptide synthesis is presented here. The synthesis of SAT is based on the cross-linking of 3-(acryloyloxy)-2-hydroxypropyl methacrylate with styrene by free-radical suspension polymerization, consisting of an ester and a secondary hydroxyl group. An additional cross-linker tri(propyleneglycol) diacryalte provides a hydrophilic environment throughout the resin, which will enhance the physicochemical properties of the resin toward organic synthesis. The resins were synthesized in various cross-linking densities to check the swelling property, mechanical stability, and functional loading capacity. The resin was characterized by the IR, (13)C NMR, and SEM techniques. The extent of swelling properties of the polymer of different cross-linking densities were studied and compared with Merrifield resin and TentaGel. To demonstrate the efficiency of SAT support was proved by synthesizing the challenging peptide sequence of acyl carrier protein (ACP) and compared with commercially available Merrifield resin. It was further tested by synthesizing endothelial receptor antagonist peptides using SAT resin and compared with commercially available TentaGel resin. The standard Fmoc strategy was adopted for peptide synthesis and was characterized by MALDI-TOF MS and analyzed the purity of peptides by HPLC.

  19. Esters of ricebran oil with short chain alcohols as alternative fuel for diesel engines

    Directory of Open Access Journals (Sweden)

    F.A. Zaher

    2016-06-01

    Full Text Available The potential of ricebran oil as a feedstock for the production of a fuel for diesel engines alternative to regular diesel fuel has been assessed. Esterification rate of crude ricebran oil with methyl alcohol was studied using different volumetric ratios of alcohol to oil, different catalyst loads and catalyst types. Catalysts used were sulfuric acid at a concentration of 2% of the oil/alcohol mixture in addition to hydrochloric acid and Amberlite IR-120 cation exchange resin at the same molar concentration of H+ as in case of sulfuric acid. The reaction was fastest using sulfuric acid which has been then used to prepare esters of ricebran oil with methyl, ethyl, propyl and butyl alcohols. The four products have been evaluated as a fuel for diesel engines according to their fuel properties compared to regular diesel fuel. These properties include the calorific value, flash point, viscosity, pour point, cetane number, sulfur content and ASTM distillation characteristics. The results have shown that the methyl as well as the ethyl esters have the closest properties to those of regular diesel fuel. Diesel engine performance using blends of regular diesel fuel with methyl and ethyl esters of ricebran oil have been tested and compared to that using regular diesel fuel. The results have shown that the engine performance using a blend of 50% regular diesel fuel and 50% methyl esters of ricebran oil is better than that using regular diesel fuel. The brake thermal efficiency at full load was 30.2% using the fuel blend compared to 27.5% in case of regular fuel.

  20. High Performance Fatty Acid-Based Vinyl Ester Resin for Liquid Molding

    National Research Council Canada - National Science Library

    Geng, Xing; La Scala, John J; Sands, James M; Palmese, Guiseppe R

    2007-01-01

    ...% compared to 40-60 wt% associated with commercial products. In addition, fatty acid-based monomers can bring about other benefits like higher toughness, lower exothermal heat and low volume shrinkage...

  1. High-Performance Bio-Based Cyanate Ester Resins with Low Moisture Uptake

    Science.gov (United States)

    2012-08-22

    available as an essential oil extracted from star anise ( Illicium verum ), an evergreen tree native to southwest China (Yunnan and Guangxi provinces) and...fruits of star anise (’’ Illicium verum ’’), taken 17th October 2006 by Brian Arthur and released under the GNU Free Documentation License. All remaining

  2. Zero birefringence films of pullulan ester derivatives

    Science.gov (United States)

    Danjo, Takahiro; Enomoto, Yukiko; Shimada, Hikaru; Nobukawa, Shogo; Yamaguchi, Masayuki; Iwata, Tadahisa

    2017-04-01

    High-performance films with almost zero-birefringence and zero-wavelength dispersion were succeeded to prepare from pullulan esters derivatives (PLEs) without any additives. Optical transmittance analysis, birefringence measurement of PLE cast film and hot stretched films, and infrared dichroism analysis were conducted to characterize optical properties of PLE films comparing with cellulose triacetate which is commercially used as low-birefringence in optical devices. The aims of this study, characterization of optical properties of pullulan esters, can develop a deep understanding of the fundamental knowing and applicability of polysaccharides. Accordingly, authors believe this paper will open the gate for researches in the application of polysaccharides.

  3. Resin technologies: construction and staining of resin TMA's.

    Science.gov (United States)

    Howat, William J; Wilson, Susan J

    2010-01-01

    The traditional formaldehyde-fixed paraffin-embedded tissue, and therefore the tissue microarrays created from it, provide good morphology but with a compromised antigenicity when compared to frozen tissue. In contrast, while solving the issue of antigenicity, frozen tissue suffers from a lack of morphology. We have demonstrated that tissue microarrays constructed in glycol methacrylate resin, when combined with a cold acetone fixation step, have been able to combine the superior morphology of resin-embedded sections with the superior antigenicity of frozen tissue for prospectively collected material.

  4. Epoxy Resins in Electron Microscopy

    Science.gov (United States)

    Finck, Henry

    1960-01-01

    A method of embedding biological specimens in araldite 502 (Ciba) has been developed for materials available in the United States. Araldite-embedded tissues are suitable for electron microscopy, but the cutting qualities of the resin necessitates more than routine attention during microtomy. The rather high viscosity of araldite 502 also seems to be an unnecessary handicap. The less viscous epoxy epon 812 (Shell) produces specimens with improved cutting qualities, and has several features—low shrinkage and absence of specimen damage during cure, minimal compression of sections, relative absence of electron beam-induced section damage, etc.—which recommends it as a routine embedding material. The hardness of the cured resin can be easily adjusted by several methods to suit the materials embedded in it. Several problems and advantages of working with sections of epoxy resins are also discussed. PMID:13822825

  5. Process for Molding Nonreinforced (Neat) Resins

    Science.gov (United States)

    Dickerson, G. E.

    1983-01-01

    Void free moldings obtained for neat, condensation, thermosetting resins. Thermally and mechanically treat resin prior to molding to reduce amount of volatiles. With volatiles reduced molding temperature and pressure are applied in way to drive out remaining volatiles during molding.

  6. 21 CFR 172.280 - Terpene resin.

    Science.gov (United States)

    2010-04-01

    ... CONSUMPTION (CONTINUED) FOOD ADDITIVES PERMITTED FOR DIRECT ADDITION TO FOOD FOR HUMAN CONSUMPTION Coatings, Films and Related Substances § 172.280 Terpene resin. The food additive terpene resin may be safely used...

  7. Action of ionizing radiation on epoxy resins

    Energy Technology Data Exchange (ETDEWEB)

    Van de Voorde, M. E.

    1970-12-01

    The resistance of classical and experimental epoxy resins to irradiation was studied. The resistance to irradiation of epoxy resins of diverse compositions as well as the development of resins having a radioresistance that approaches that of certain ceramics are discussed. Sources of irradiation and the techniques of dosimetry used are described. The structures of certain epoxy resins and of hardeners are given. The preparation of these resins and their physical properties is described. The effects of radiation on epoxy resins, as well as conditions of irradiation, and suggested mechanisms for degradation of the irradiated resins are discussed. The relationship between chemical structure of the resins and their physical properties is evaluated. (115 references) (JCB)

  8. Synthesis and stability of new spiroaminoborate esters

    OpenAIRE

    Stepanenko, Viatcheslav; de Jesús, Melvin; Garcia, Carmelo; Barnes, Charles L.; Ortiz-Marciales, Margarita

    2012-01-01

    New spiroaminoborate esters derived from 1,1-diphenylprolinol, ephedrine and dihydroquinine with different alkoxy substituents were prepared as stable crystalline compounds and characterized by spectroscopical analysis and specific rotation. The structure of the spiroborate 4 derived from 1,1-diphenylprolinol and dicyclohexyl-1,1′-diol was confirmed by X-ray analysis.

  9. 1347-IJBCS-Article-Dr Innocent Ester

    African Journals Online (AJOL)

    KODJIO NORBERT

    Say (Culicidae: Diptera). Ester INNOCENT 1*, Eliangiringa KAALE 2 and Zakaria H. MBWAMBO 1. 1 Institute of Traditional Medicine, Muhimbili University of Health and Allied Sciences,. P.O. Box 65001, Dar es Salaam, Tanzania. 2Department of Medicinal Chemistry, School of Pharmacy, Muhimbili University of Health and ...

  10. Two New Phorbol Esters from Euphorbia bothae

    African Journals Online (AJOL)

    NICO

    Euphorbias of South Africa: Two New Phorbol Esters from. Euphorbia bothae. Wendy L. Popplewell,1 Eloise A. Marais,1 Linda Brand,2. Brian H. Harvey2 and Michael T. Davies-Coleman1*. 1Department of Chemistry, Rhodes University, Grahamstown, 6140 South Africa. 2Unit for Drug Research and Development, Division ...

  11. Naturally Occurring Cinnamic Acid Sugar Ester Derivatives

    Directory of Open Access Journals (Sweden)

    Yuxin Tian

    2016-10-01

    Full Text Available Cinnamic acid sugar ester derivatives (CASEDs are a class of natural product with one or several phenylacrylic moieties linked with the non-anomeric carbon of a glycosyl skeleton part through ester bonds. Their notable anti-depressant and brains protective activities have made them a topic of great interest over the past several decades. In particular the compound 3′,6-disinapoylsucrose, the index component of Yuanzhi (a well-known Traditional Chinese Medicine or TCM, presents antidepressant effects at a molecular level, and has become a hotspot of research on new lead drug compounds. Several other similar cinnamic acid sugar ester derivatives are reported in traditional medicine as compounds to calm the nerves and display anti-depression and neuroprotective activity. Interestingly, more than one third of CASEDs are distributed in the family Polygalaceae. This overview discusses the isolation of cinnamic acid sugar ester derivatives from plants, together with a systematic discussion of their distribution, chemical structures and properties and pharmacological activities, with the hope of providing references for natural product researchers and draw attention to these interesting compounds.

  12. Avocado and olive oil methyl esters

    Science.gov (United States)

    Biodiesel, the mono-alkyl esters of vegetable oils, animal fats or other triacylglycerol-containing materials and an alternative to conventional petroleum-based diesel fuel, has been derived from a variety of feedstocks. Numerous feedstocks have been investigated as potential biodiesel sources, incl...

  13. Method for loading resin beds

    International Nuclear Information System (INIS)

    Notz, K.J.; Rainey, R.H.; Greene, C.W.; Shockley, W.E.

    1978-01-01

    An improved method of preparing nuclear reactor fuel by carbonizing a uranium loaded cation exchange resin provided by contacting a H+ loaded resin with a uranyl nitrate solution deficient in nitrate, comprises providing the nitrate deficient solution by a method comprising the steps of reacting in a reaction zone maintained between about 145 to 200 0 C, a first aqueous component comprising a uranyl nitrate solution having a boiling point of at least 145 0 C with a second aqueous component to provide a gaseous phase containing HNO 3 and a reaction product comprising an aqueous uranyl nitrate solution deficient in nitrate

  14. Uranium sorption by tannin resins

    International Nuclear Information System (INIS)

    Olivares Rieumont, S.; Martinez Luzardo, J.; Torres Hernandez, J.; Lima Cazorla, D. de la Rosa.

    1998-01-01

    The sorption of uranium by immobilised Eucalyptus Saligna Sm. and Lysiloma latisiliqua L tannins was investigated. Immobilization condition were analyzed. These resins resulted suitable adsorbent for the concentration of uranium from aqueous systems. The sorption of uranium is pH dependent. At pH 5.5 maximum in sorption capacity is registered. The presence of appreciable amount of sodium chloride do not have any effect on uranium removal. Carbonate and calcium ions in concentrations similar to these that could be found in sea water and other natural water do not decrease the uranium uptake. Tannin resins can be used several times without an appreciable decay of their sorption capacity

  15. Ester Tuiksoo - Eesti esimene naissoost põllumajandusminister / Ester Tuiksoo ; interv. Toomas Verrev

    Index Scriptorium Estoniae

    Tuiksoo, Ester, 1965-

    2007-01-01

    Ametist lahkuv põllumajandusminister Ester Tuiksoo räägib saadud juhtimiskogemusest, Euroopa Liidu ühise põllumajanduspoliitika juurutamisest, rahvuskala valimisest, Rahvaliidu käekäigust parlamendivalimistel

  16. QSAR for cholinesterase inhibition by organophosphorus esters and CNDO/2 calculations for organophosphorus ester hydrolysis

    Science.gov (United States)

    Johnson, H.; Kenley, R. A.; Rynard, C.; Golub, M. A.

    1985-01-01

    Quantitative structure-activity relationships were derived for acetyl- and butyrylcholinesterase inhibition by various organophosphorus esters. Bimolecular inhibition rate constants correlate well with hydrophobic substituent constants, and with the presence or absence of catonic groups on the inhibitor, but not with steric substituent constants. CNDO/2 calculations were performed on a separate set of organophosphorus esters, RR'P(O)X, where R and R' are alkyl and/or alkoxy groups and X is fluorine, chlorine or a phenoxy group. For each subset with the same X, the CNDO-derived net atomic charge at the central phosphorus atom in the ester correlates well with the alkaline hydrolysis rate constant. For the whole set of esters with different X, two equations were derived that relate either charge and leaving group steric bulk, or orbital energy and bond order to the hydrogen hydrolysis rate constant.

  17. Euphorbias of South Africa: Two New Phorbol Esters from ...

    African Journals Online (AJOL)

    Euphorbias of South Africa: Two New Phorbol Esters from Euphorbia bothae. ... WL Popplewell, EA Marais, L Brand, BH Harvey, MT Davies-Coleman. Abstract. Two known phorbol esters, 12-deoxyphorbol-13-isobutyrate-20-acetate (1) and 12-deoxyphorbol-13-(2-methylbutyrate)-20-acetate (2), and two new phorbol esters, ...

  18. Biocatalytic synthesis and antioxidant capacities of ascorbyl esters ...

    African Journals Online (AJOL)

    ajl yemi

    2011-11-28

    Nov 28, 2011 ... available on the comparison of antioxidant activities of ascorbyl esters biosynthesized using alkyl ester, fatty acid and triglyceride as acyl donors. Therefore, this study focused on the enzymatic synthesis of L-ascorbyl acid fatty acid esters catalyzed by immobilized lipase from C. antarctica (Novozym 435) in.

  19. 21 CFR 172.848 - Lactylic esters of fatty acids.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Lactylic esters of fatty acids. 172.848 Section 172... CONSUMPTION Multipurpose Additives § 172.848 Lactylic esters of fatty acids. Lactylic esters of fatty acids... prepared from lactic acid and fatty acids meeting the requirements of § 172.860(b) and/or oleic acid...

  20. 21 CFR 172.859 - Sucrose fatty acid esters.

    Science.gov (United States)

    2010-04-01

    ... solvents which may be used in the preparation of sucrose fatty acid esters are those generally recognized... preparation of sucrose fatty acid esters. (b) Sucrose fatty acid esters meet the following specifications: (1..., 5100 Paint Branch Pkwy., College Park, MD 20740, or available for inspection at the National Archives...

  1. 21 CFR 175.210 - Acrylate ester copolymer coating.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acrylate ester copolymer coating. 175.210 Section... COATINGS Substances for Use as Components of Coatings § 175.210 Acrylate ester copolymer coating. Acrylate ester copolymer coating may safely be used as a food-contact surface of articles intended for packaging...

  2. Activated Sludge Biodegradation of 12 Commercial Phthalate Esters

    OpenAIRE

    O'Grady, Dean P.; Howard, Philip H.; Werner, A. Frances

    1985-01-01

    The activated sludge biodegradability of 12 commercial phthalate esters was evaluated in two test systems: (i) a semicontinuous activated sludge test and (ii) an acclimated 19-day die-away procedure. Both procedures demonstrated that phthalate esters are rapidly biodegraded under activated sludge conditions when loss of the parent phthalate ester (primary degradation) is measured.

  3. Celorbicol, isocelorbicol, and their esters: new sesquiterpenoids from Celastrus orbiculatus

    Energy Technology Data Exchange (ETDEWEB)

    Smith, C.R. Jr. (Dept. of Agriculture, Peoria, IL); Miller, R.W.; Weisleder, D.; Rohwedder, W.K.; Eickman, N.; Clardy, J.

    1976-10-01

    Esters of two new sesquiterpenoid polyalcohols - celorbicol and isocelorbicol - have been isolated from Celastrus orbiculatus. Structures of the parent alcohols have been established by x-ray crystallography, and those of the derived esters have been assigned by NMR spectroscopy. These compounds are structurally related to other polyesters and ester alkaloids from the Celastraceae, all of which are based on the dihydroagarofuran ring system.

  4. Method of removing contaminants from plastic resins

    Energy Technology Data Exchange (ETDEWEB)

    Bohnert, George W. (Harrisonville, MO); Hand, Thomas E. (Lee' s Summit, MO); DeLaurentiis, Gary M. (Jamestown, CA)

    2008-11-18

    A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

  5. Method of removing contaminants from plastic resins

    Energy Technology Data Exchange (ETDEWEB)

    Bohnert,George W. (Harrisonville, MO); Hand,Thomas E. (Lee' s Summit, MO); Delaurentiis,Gary M. (Jamestown, CA)

    2007-08-07

    A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

  6. Method for removing contaminants from plastic resin

    Science.gov (United States)

    Bohnert, George W.; Hand, Thomas E.; DeLaurentiis, Gary M.

    2008-12-30

    A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

  7. Poly(ester-anhydride):poly(beta-amino ester) micro- and nanospheres: DNA encapsulation and cellular transfection.

    Science.gov (United States)

    Pfeifer, Blaine A; Burdick, Jason A; Little, Steve R; Langer, Robert

    2005-11-04

    Poly(ester-anhydride) delivery devices allow flexibility regarding carrier dimensions (micro- versus nanospheres), degradation rate (anhydride versus ester hydrolysis), and surface labeling (through the anhydride functional unit), and were therefore tested for DNA encapsulation and transfection of a macrophage P388D1 cell line. Poly(l-lactic acid-co-sebacic anhydride) and poly(l-lactic acid-co-adipic anhydride) were synthesized through melt condensation, mixed with 25 wt.% poly(beta-amino ester), and formulated with plasmid DNA (encoding firefly luciferase) into micro- and nanospheres using a double emulsion/solvent evaporation technique. The micro- and nanospheres were then characterized (size, morphology, zeta potential, DNA release) and assayed for DNA encapsulation and cellular transfection over a range of poly(ester-anhydride) copolymer ratios. Poly(ester-anhydride):poly(beta-amino ester) composite microspheres (6-12 microm) and nanospheres (449-1031 nm), generated with copolymers containing between 0 and 25% total polyanhydride content, encapsulated plasmid DNA (>or=20% encapsulation efficiency). Within this polyanhydride range, poly(adipic anhydride) copolymers provided DNA encapsulation at an increased anhydride content (10%, microspheres; 10-25%, nanospheres) compared to poly(sebacic anhydride) copolymers (1%, microspheres and nanospheres) with cellular transfection correlating with the observed DNA encapsulation.

  8. Rearrangement of beta,gamma-unsaturated esters with thallium trinitrate: synthesis of indans bearing a beta-keto ester moiety

    Directory of Open Access Journals (Sweden)

    Silva Jr. Luiz F.

    2006-01-01

    Full Text Available The rearrangement of beta,gamma-unsaturated esters, such as 2-(3,4-dihydronaphthalen-1-yl-propionic acid ethyl ester, with thallium trinitrate (TTN in acetic acid leads to 3-indan-1-yl-2-methyl-3-oxo-propionic acid ethyl ester in good yield, through a ring contraction reaction. The new indans thus obtained feature a beta-keto ester moiety, which would be useful for further functionalization.

  9. Seasonal variation and resin composition in the Andean tree Austrocedrus chilensis.

    Science.gov (United States)

    Olate, Verónica Rachel; Soto, Alex; Schmeda-Hirschmann, Guillermo

    2014-05-21

    Little is known about the changes in resin composition in South American gymnosperms associated with the different seasons of the year. The diterpene composition of 44 resin samples from seven Austrocedrus chilensis (Cupressaceae) trees, including male and female individuals, was investigated in three different seasons of the year (February, June and November). Twelve main diterpenes were isolated by chromatographic means and identified by gas chromatography-mass spectrometry and nuclear magnetic resonance (NMR). The diterpene composition was submitted to multivariate analysis to find possible associations between chemical composition and season of the year. The principal component analysis showed a clear relation between diterpene composition and season. The most characteristic compounds in resins collected in summer were Z-communic acid (9) and 12-oxo-labda-8(17),13E-dien-19 oic acid methyl ester (10) for male trees and 8(17),12,14-labdatriene (7) for female trees. For the winter samples, a clear correlation of female trees with torulosic acid (6) was observed. In spring, E-communic acid (8) and Z-communic acid (9) were correlated with female trees and 18-hydroxy isopimar-15-ene (1) with male tree resin. A comparison between percent diterpene composition and collection time showed p < 0.05 for isopimara-8(9),15-diene (2), sandaracopimaric acid (4), compound (7) and ferruginol (11).

  10. Cyanate ester-nanoparticle composites as multifunctional structural capacitors

    Science.gov (United States)

    De Leon, J. Eliseo

    An important goal of engineering is to increase the energy density of electrical energy storage devices used to deliver power onboard mobile platforms. Equally important is the goal to reduce the overall mass of the vehicles transporting these devices to achieve increased fuel and cost efficiency. One approach to meeting both these objectives is to develop multifunctional systems that serve as both energy storage and load bearing structural devices. Multifunctional devices consist of constituents that individually perform a subset of the overall desired functions. However, the synergy achieved by the combination of each constituent's characteristics allows for system-level benefits that cannot be achieved by simply optimizing the separate subsystems. We investigated multifunctional systems consisting of light weight polymer matrix and high dielectric constant fillers to achieve these objectives. The monomer of bisphenol E cyanate ester exhibited excellent processing ability because of its low room temperature viscosity. Additionally, the fully cured thermoset demonstrated excellent thermal stability, specific strength and stiffness. Fillers, including multi-walled carbon nanotubes, nanometer scale barium titanate and nanometer scale calcium copper titanate, offer high dielectric constants that raised the effective dielectric constant of the polymer matrix composite. The combination of high epsilon'and high dielectric strength produce high energy density components exhibiting increased electrical energy storage. Mechanical (load bearing) improvements of the PMCs were attributed to covalently bonded nanometer and micrometer sized filler particles, as well as the continuous glass fiber, integrated into the resin systems which increased the structural characteristics of the cured composites. Breakdown voltage tests and dynamic mechanical analysis were employed to demonstrate that precise combinations of these constituents, under the proper processing conditions, can

  11. Diterpene resin acids in conifers.

    Science.gov (United States)

    Keeling, Christopher I; Bohlmann, Jörg

    2006-11-01

    Diterpene resin acids are a significant component of conifer oleoresin, which is a viscous mixture of terpenoids present constitutively or inducibly upon herbivore or pathogen attack and comprises one form of chemical resistance to such attacks. This review focuses on the recent discoveries in the chemistry, biosynthesis, molecular biology, regulation, and biology of these compounds in conifers.

  12. Occupational exposure to epoxy resins

    NARCIS (Netherlands)

    Terwoert, J.; Kersting, K.

    2014-01-01

    Products based on epoxy resins as a binder have become popular in various settings, among which the construction industry and in windmill blade production, as a result of their excellent technical properties. However, due to the same properties epoxy products are a notorious cause of allergic skin

  13. Batatins VIII-XI, glycolipid ester-type dimers from Ipomoea batatas.

    Science.gov (United States)

    Rosas-Ramírez, Daniel; Pereda-Miranda, Rogelio

    2015-01-23

    Sweet potato (Ipomoea batatas) is native to the tropics of Central and South America, where many varieties have been consumed for more that 5000 years. In developing countries, this crop is a recognized effective food for fighting malnutrition. Purification of the minor lipophilic glicolipids found in the n-hexane-soluble resin glycosides from the white-skinned variety was performed by preparative-scale recycling HPLC. Application of column overload, peak shaving, heart cutting, and recycling techniques permitted the purification of four new oligosaccharide ester-type dimer derivatives of jalapinolic acid, batatins VIII-XI (1-4). The structural characterization of these complex lipo-oligosaccharides was performed through NMR spectroscopy and MS, indicating that batatins VIII-XI (1-4) possess an oligomeric structure consisting of two pentasaccharide units of the known simonic acid B.

  14. Influence of Stitching Parameters on Tensile Strength of Aramid/Vinyl Ester Composites

    Directory of Open Access Journals (Sweden)

    Mehmet KARAHAN

    2013-03-01

    Full Text Available Stitching process is used to provide structural integrity and through-the-thickness reinforcement in the composite materials. In this study, the effect of sewing parameters on tensile strength in stitched composite laminates was examined. In the production of composite laminates, Twaron T-750 type plain weave fabric was used as reinforcement material and a Polives 702 Bisphenol-A type epoxy based vinyl ester as resin. The effects of stitch density and stitch direction or stitch pattern on tensile strength of composite samples were studied and, as a result of the experiments, it was observed that higher tensile strength occurs with low stitch densities in stitched laminates.DOI: http://dx.doi.org/10.5755/j01.ms.19.1.3829

  15. Mechanical and dielectric properties of epoxy/dicyclopentadiene bisphenol cyanate ester/glass fabric composites

    Directory of Open Access Journals (Sweden)

    2008-02-01

    Full Text Available The impact and flexural strengths of epoxy-dicyclopentadiene bisphenol cyanate ester (EP-DCPDCE hybrid thermoset as well as the interlaminar shear strength (ILSS and flexural strength of the composites consisting of the hybrid thermoset and glass fabric were studied. It is found that the addition of epoxy resin (EP-51 can improve the mechanical properties, particularly, the impact strength of DCPDCE matrix and the ILSS of glass fabric reinforced composites. The improvements of the mechanical properties were obvious when the content of EP-51 is from 15 to 30 wt%. The investigations of the interphase of composites by scanning electron microscope (SEM and dynamic mechanical analysis (DMA confirm the improvement of mechanical properties of the composites. However the addition of EP-51 has negative effects on the thermal and dielectric property of the composites.

  16. Viscoelastic and shock response of nanoclay and graphite platelet reinforced vinyl ester nanocomposites

    Science.gov (United States)

    Almagableh, Ahmad Mohammad

    The focus of ongoing research at University of Mississippi is to develop stronger, safer and more cost-effective structural materials for the new generation naval ships with an emphasis on lightweight nanoparticle reinforced glass/carbon polymeric based composites and structural foams for blast, shock and impact mitigation. Brominated 510A-40 vinyl ester nanocomposite resin systems are planned to be used in the composite face sheets of sandwich structures with fire-resistant foam layered in between to further reduce flammability along with optimal flexural rigidity, vibration damping and enhanced energy absorption. In this work, the viscoelastic and dynamic performance of brominated nanoclay and graphite platelet reinforced vinyl ester nanocomposites for blast (shock) loading applications are studied. The Dynamic Mechanical Analyzer (DMA Q800) was used to obtain the viscoelastic properties, modulus (stiffness), creep/ stress relaxation, and damping (energy dissipation), of 1.25 and 2.5 wt. percent nanoclay and exfoliated graphite nanoplatelet (xGnP) reinforced brominated vinyl ester. Effects of frequency (time) on the viscoelastic behavior were investigated by sweeping the frequency over three decades: 0.01, 0.1, 1 and 10 Hz, and temperature range from 30-150°C at a step rate of 4°C per minute. Master curves were generated by time-temperature superpositioning of the experimental data at a reference temperature. Bromination of vinyl ester resin was found to significantly increase the glass transition temperature (Tg) and damping for all nanocomposites. The nano reinforced composites, however showed a drop in initial storage modulus with bromination. Nanocomposites with 1.25 and 2.5 M. percent graphite had the highest storage modulus along with the lowest damping among brominated specimens. In this research, a shock Tube, servo-hydraulic Material Testing System (MTS) and Split-Hopkinson Pressure Bar (SHPB) are used to characterize the mechanical response and energy

  17. Real-Time monitoring of intracellular wax ester metabolism

    Directory of Open Access Journals (Sweden)

    Karp Matti

    2011-09-01

    Full Text Available Abstract Background Wax esters are industrially relevant molecules exploited in several applications of oleochemistry and food industry. At the moment, the production processes mostly rely on chemical synthesis from rather expensive starting materials, and therefore solutions are sought from biotechnology. Bacterial wax esters are attractive alternatives, and especially the wax ester metabolism of Acinetobacter sp. has been extensively studied. However, the lack of suitable tools for rapid and simple monitoring of wax ester metabolism in vivo has partly restricted the screening and analyses of potential hosts and optimal conditions. Results Based on sensitive and specific detection of intracellular long-chain aldehydes, specific intermediates of wax ester synthesis, bacterial luciferase (LuxAB was exploited in studying the wax ester metabolism in Acinetobacter baylyi ADP1. Luminescence was detected in the cultivation of the strain producing wax esters, and the changes in signal levels could be linked to corresponding cell growth and wax ester synthesis phases. Conclusions The monitoring system showed correlation between wax ester synthesis pattern and luminescent signal. The system shows potential for real-time screening purposes and studies on bacterial wax esters, revealing new aspects to dynamics and role of wax ester metabolism in bacteria.

  18. Synthesis of Estolide 2-ethylhexyl Ester from Ricinus communis

    International Nuclear Information System (INIS)

    Nazrizawati Ahmad Tajuddin; Nor Habibah Rosli

    2013-01-01

    Estolide 2-ethylhexyl ester synthesized through condensation reaction between ricinoleic acid from castor oil (Ricinus communis) and lauric acid, and then capped with 2-ethylhexyl alcohol. The reaction was continuously conducted under vacuum for 24 hours. Product of 2-ethylhexyl ester was characterized by using Fourier Transform Infrared (FTIR) to determine functional group and Nuclear Magnetic Resonans (NMR) for structure's determination. The presence of ester group at 1738.23 cm -1 wavenumber indicates that the formation of estolide ester has occurred. The vibration peak of C-O at 1174.60 cm -1 and 1117.10 cm -1 support the formation of ester. The presence of CH 2 bending indicated the long-chain compound. The ester methine signal at 3.8669 ppm indicated the estolide linkage in the 1 H-NMR spectrum while the 13 C-NMR showed two carbonyl signals at 173.41 ppm for acid and 173.56 ppm for ester. (author)

  19. EDF specifications on nuclear grade resins

    International Nuclear Information System (INIS)

    Mascarenhas, Darren; Gressier, Frederic; Taunier, Stephane; Le-Calvar, Marc; Ranchoux, Gilles; Marteau, Herve; Labed, Veronique

    2012-09-01

    Ion exchange resins are widely used across EDF, especially within the nuclear division for the purification of water. Important applications include primary circuit, secondary circuit and effluent treatment, which require high quality nuclear grade resins to retain the dissolved species, some of which may be radioactive. There is a need for more and more efficient purification in order to decrease worker dose during maintenance but also to decrease volumes of radioactive resin waste. Resin performance is subject to several forms of degradation, including physical, chemical, thermal and radioactive, therefore appropriate resin properties have to be selected to reduce such effects. Work has been done with research institutes, manufacturers and on EDF sites to select these properties, create specifications and to continuously improve on these specifications. An interesting example of research regarding resin performance is the resin degradation under irradiation. Resins used in the CVCS circuit of EDF nuclear power plants are subject to irradiation over their lifetime. A study was carried out on the effects of total integrated doses of 0.1, 1 and 10 MGy on typically used EDF mixed bed resins in a 'mini-CVCS' apparatus to simultaneously test actual primary circuit fluid. The tests confirmed that the resins still perform efficiently after a typical CVCS radiation dose. Certain resins also need additional specifications in order to maintain the integrity of the particular circuits they are used in. Recently, EDF has updated its requirements on these high purity nuclear grade resins, produced generic doctrines for all products and materials used on site which include resins of all grades, and as a result have also updated a guide on recommended resin usage for the French fleet of reactors. An overview of the evolutions will be presented. (authors)

  20. Enzymatic synthesizing of phytosterol oleic esters.

    Science.gov (United States)

    Pan, Xinxin; Chen, Biqiang; Wang, Juan; Zhang, Xinzhi; Zhul, Biyun; Tan, Tianwei

    2012-09-01

    A method of synthesizing the phytosterol esters from oleic acid and sterols was studied, using immobilized lipase Candida sp. 99-125 as catalyst. Molar ratio (oleic acid/phytosterols), temperature, reaction period, organic solvents, catalyst, and silica-gel drier were optimized, and the result showed that 93.4% of the sterols had been esterified under the optimal synthetic condition: the molar ratio of oleic acid/phytosterol is 1:1 in 10 mL iso-octane, immobilized lipase (w, 140% of the sterols), incubated in an orbital shaker (200 rpm) at a temperature of 45 °C for 24 h. The immobilized lipase could be reused for at least 13 times with limited loss of esterification activity. The conversion still maintained up to 86.6%. Hence, this developed process for synthesizing phytosterol esters could be considered as simple and low-energy consumption compared to existing chemical processes.

  1. Atmospheric oxidation of selected alcohols and esters

    Energy Technology Data Exchange (ETDEWEB)

    Becker, K.H.; Cavalli, F.

    2001-03-01

    The decision whether it is appropriate and beneficial for the environment to deploy specific oxygenated organic compounds as replacements for traditional solvent types requires a quantitative assessment of their potential atmospheric impacts including tropospheric ozone and other photooxidant formation. This involves developing chemical mechanisms for the gasphase atmospheric oxidation of the compounds which can be reliably used in models to predict their atmospheric reactivity under a variety of environmental conditions. Until this study, there was very little information available concerning the atmospheric fate of alcohols and esters. The objectives of this study were to measure the atmospheric reaction rates and to define atmospheric reaction mechanisms for the following selected oxygenated volatile organic compounds: the alcohols, 1-butanol and 1-pentanol, and the esters, methyl propionate and dimethyl succinate. The study has successfully addressed these objectives. (orig.)

  2. Naturally occurring antifungal aromatic esters and amides

    International Nuclear Information System (INIS)

    Ali, M.S.; Shahnaz; Tabassum, S.; Ogunwande, I.A.; Pervez, M.K.

    2010-01-01

    During the search of antifungal natural products from terrestrial plants, a new long chained aromatic ester named grandiflorate along with spatazoate from Portulaca grandiflora and N-[2-methoxy-2-(4-methoxyphenyl) ethyl]-trans-cinnamide and aegeline from Solanum erianthum of Nigeria were isolated and tested against six fungal species. The known constituents have not been reported so far from mentioned investigated plants. Structures of the isolated compounds were elucidated with the aid of spectroscopic techniques including two dimensional NMR experiments. Among the compounds, the esters found more potent than amides against Candida albicans and Aspergillus flavus. The new compound grandiflorate gave response against all tested fungal species while aegeline was found to give lowest inhibition during this study. (author)

  3. Synthetic Methods for Ester Bond Formation and Conformational Analysis of Ester-Containing Carbohydrates

    Science.gov (United States)

    Hackbusch, Sven

    This dissertation encompasses work related to synthetic methods for the formation of ester linkages in organic compounds, as well as the investigation of the conformational influence of the ester functional group on the flexibility of inter-saccharide linkages, specifically, and the solution phase structure of ester-containing carbohydrate derivatives, in general. Stereoselective reactions are an important part of the field of asymmetric synthesis and an understanding of their underlying mechanistic principles is essential for rational method development. Here, the exploration of a diastereoselective O-acylation reaction on a trans-2-substituted cyclohexanol scaffold is presented, along with possible reasons for the observed reversal of stereoselectivity dependent on the presence or absence of an achiral amine catalyst. In particular, this work establishes a structure-activity relationship with regard to the trans-2-substituent and its role as a chiral auxiliary in the reversal of diastereoselectivity. In the second part, the synthesis of various ester-linked carbohydrate derivatives, and their conformational analysis is presented. Using multidimensional NMR experiments and computational methods, the compounds' solution-phase structures were established and the effect of the ester functional group on the molecules' flexibility and three-dimensional (3D) structure was investigated and compared to ether or glycosidic linkages. To aid in this, a novel Karplus equation for the C(sp2)OCH angle in ester-linked carbohydrates was developed on the basis of a model ester-linked carbohydrate. This equation describes the sinusoidal relationship between the C(sp2)OCH dihedral angle and the corresponding 3JCH coupling constant that can be determined from a J-HMBC NMR experiment. The insights from this research will be useful in describing the 3D structure of naturally occurring and lab-made ester-linked derivatives of carbohydrates, as well as guiding the de novo-design of

  4. Methyl and ethyl soybean esters production

    Energy Technology Data Exchange (ETDEWEB)

    Pighinelli, Anna Leticia Montenegro Turtelli; Park, Kil Jin; Zorzeto, Thais Queiroz [Universidade Estadual de Campinas (FEAGRI/UNICAMP), SP (Brazil). Fac. de Engenharia Agricola], E-mail: annalets@feagri.unicamp.br; Bevilaqua, Gabriela [Universidade Estadual de Campinas (IQ/UNICAMP), SP (Brazil). Inst. de Quimica

    2008-07-01

    Biodiesel is a fuel obtained from triglycerides found in nature, like vegetable oils and animal fats. Nowadays it has been the subject of many researches impulses by the creation of the Brazilian law that determined the blend of 2% of biodiesel with petrodiesel. Basically, there are no limitations on the oilseed type for chemical reaction, but due to high cost of this major feedstock, it is important to use the grain that is available in the region of production. Soybean is the oilseed mostly produced in Brazil and its oil is the only one that is available in enough quantity to supply the current biodiesel demand. The objective of this work was to study the effects of reaction time and temperature on soybean oil transesterification reaction with ethanol and methanol. A central composite experimental design with five variation levels was used and response surface methodology applied for the data analysis. The statistical analysis of the results showed that none of the factors affected the ethyl esters production. However, the methyl esters production suffered the influence of temperature (linear effect), reaction time (linear and quadratic) and interaction of these two variables. None of the generated models showed significant regression consequently it was not possible to build the response surface. The experiments demonstrated that methanol is the best alcohol for transesterification reactions and the ester yield was up to 85%. (author)

  5. On-resin N-formylation of peptides: a head-to-head comparison of reagents in solid-phase synthesis of ligands for formyl peptide receptors

    DEFF Research Database (Denmark)

    Christensen, Simon Bendt; Hansen, Anna Mette; Franzyk, Henrik

    2017-01-01

    General conditions for efficient on-resin N-formylation of peptides were identified by screening of a number of reagents comprising aliphatic formates (ethyl formate, 2,2,2-trifluoroethyl formate, and cyanomethyl formate), aromatic esters (phenyl formate and p-nitrophenyl formate), and N-formylim......General conditions for efficient on-resin N-formylation of peptides were identified by screening of a number of reagents comprising aliphatic formates (ethyl formate, 2,2,2-trifluoroethyl formate, and cyanomethyl formate), aromatic esters (phenyl formate and p-nitrophenyl formate), and N......-formylimidazole and in situ activation of formic acid with the coupling reagent 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide. Initially, reaction time and influence of solvent were examined for the formylation of a short model peptide. The most efficient reagents were examined further by using different linkers and solid...

  6. Foam, Foam-resin composite and method of making a foam-resin composite

    Science.gov (United States)

    Cranston, John A. (Inventor); MacArthur, Doug E. (Inventor)

    1995-01-01

    This invention relates to a foam, a foam-resin composite and a method of making foam-resin composites. The foam set forth in this invention comprises a urethane modified polyisocyanurate derived from an aromatic amino polyol and a polyether polyol. In addition to the polyisocyanurate foam, the composite of this invention further contains a resin layer, wherein the resin may be epoxy, bismaleimide, or phenolic resin. Such resins generally require cure or post-cure temperatures of at least 350.degree. F.

  7. Vinyl Ester Oligomer Crosslinked Porous Polymers Prepared via Surfactant-Free High Internal Phase Emulsions

    Directory of Open Access Journals (Sweden)

    Yun Zhu

    2012-01-01

    Full Text Available Using vinyl ester resin (VER containing styrene (or methyl methacrylate and vinyl ester oligomer (VEO as external phase, Pickering high internal phase emulsions (Pickering HIPEs having internal phase volume fraction of up to 95 vol% were prepared with copolymer particles as sole stabilizer. Polymerizing the external phase of these Pickering HIPEs led to porous polymers (poly-Pickering-HIPEs. Compared to the polystyrene- (PS- based poly-Pickering-HIPEs which were prepared with mixture of styrene and divinylbenzene (DVB as crosslinker, the poly-Pickering-HIPEs herein showed much higher elastic modulus and toughness. The elastic modulus of these poly-Pickering-HIPEs increased with increasing the VEO concentration in the external phase, while it decreased with increasing internal phase volume fraction. Increasing VEO concentration in the external phase also resulted in a decrease in the average void diameter as well as a narrow void diameter distribution of the resulting poly-Pickering-HIPEs. In addition, there were many small pores in the voids surface caused by the volume contraction of VER during the polymerization, which suggests a new method to fabricate porous polymers having a well-defined hierarchical pore structure.

  8. Interpenetrating polymer networks based on cyanate ester and fluorinated ethynyl-terminated imide oligomers

    Directory of Open Access Journals (Sweden)

    Y. Wen

    2017-12-01

    Full Text Available Highly soluble fluorinated ethynyl-terminated imide (FETI oligomers were prepared via a conventional one-step method in m-cresol, using 4, 4′-(hexafluoroisopropylidene diphthalic anhydride and 2, 2′-bis(trifluoromethyl benzidine as the monomers, and ethynylphthalic anhydride as the end-capper; then interpenetrating polymer networks (IPN were formulated from FETI oligomers and bisphenol A dicyanate ester (BADCy through a solvent-free procedure, and their thermal, mechanical, and dielectric properties were fully characterized. The curing mechanism was studied by model reactions using nitrogen nuclear magnetic resonance. As evidenced by differential scanning calorimetry analysis and rheological measurements, the FETI/BADCy blends exhibited lower curing temperature and shorter gelation time in comparison with pure BADCy due to the catalytic effects of ethynyl and residue amic acid groups. The properties of IPNs were fully compared with those of polycyanurate, and the results revealed that the incorporation of FETI into cyanate ester resins could significantly improve the toughness, glass transition temperatures, mechanical and dielectric properties of the resultant IPNs.

  9. Potential problems associated with ion-exchange resins used in the decontamination of light-water reactor systems

    International Nuclear Information System (INIS)

    Soo, P.; Adams, J.W.; Kempf, C.R.

    1987-01-01

    During a typical decontamination event, ion-exchange resin beds are used to remove corrosion products (radioactive and nonradioactive) and excess decontamination reagents from waste streams. The spent resins may be solidified in a binder, such as cement, or sealed in a high-integrity container (HIC) in order to meet waste stability requirements specified by the Nuclear Regulatory Commission. Lack of stability of low-level waste in a shallow land burial trench may lead to trench subsidence, enhanced water infiltration and waste leaching, which would result in accelerated transport of radionuclides and the complexing agents used for decontamination. The current program is directed at investigating safety problems associated with the handling, solidification and containerization of decontamination resin wastes. The three tasks currently underway include freeze-thaw cycling of cementitious and vinyl ester-styrene forms to determine if mechanical integrity is compromised, a study of the corrosion of container materials by spent decontamination waste resins, and investigations of resin degradation mechanisms

  10. Space charge dynamic of irradiated cyanate ester/epoxy at cryogenic temperatures

    Science.gov (United States)

    Wang, Shaohe; Tu, Youping; Fan, Linzhen; Yi, Chengqian; Wu, Zhixiong; Li, Laifeng

    2018-03-01

    Glass fibre reinforced polymers (GFRPs) have been widely used as one of the main electrical insulating structures for superconducting magnets. A new type of GFRP insulation material using cyanate ester/epoxy resin as a matrix was developed in this study, and the samples were irradiated by Co-60 for 1 MGy and 5 MGy dose. Space charge distributed within the sample were tested using the pulsed electroacoustic method, and charge concentration was found at the interfaces between glass fibre and epoxy resin. Thermally stimulated current (TSC) and dc conduction current were also tested to evaluate the irradiation effect. It was supposed that charge mobility and density were suppressed at the beginning due to the crosslinking reaction, and for a higher irradiation dose, molecular chain degradation dominated and led to more sever space charge accumulation at interfaces which enhance the internal electric field higher than the external field, and transition field for conduction current was also decreased by irradiation. Space charge dynamic at cryogenic temperature was revealed by conduction current and TSC, and space charge injection was observed for the irradiated samples at 225 K, which was more obvious for the irradiated samples.

  11. Synthesis of Hydrophobic, Crosslinkable Resins.

    Science.gov (United States)

    1984-12-01

    Bismaleimides have also been crosslinked with radical initiators to produce brittle networks [4].If a damine is added, chain extension and radical crosslinkinq...are produced during cure.The company also produced a similar phenylene based resin, with pendant nitrile groups which could be crosslinked without the...benzenes and tetra substituted cyclopentadienones [881. g. Preparation of poly 1,4 phenylene by nickel (0> catalysed electropolymerisation 1891. Cont’d

  12. Evaluation of adhesion of reline resins to the thermoplastic denture base resin for non-metal clasp denture.

    Science.gov (United States)

    Kim, Ji Hye; Choe, Han Cheol; Son, Mee Kyoung

    2014-01-01

    This study aimed to evaluate the tensile and transverse bond strength of chairside reline resins (Tokuyama Rebase II, Mild Rebaron LC) to a thermoplastic acrylic resin (Acrytone) used for non metal clasp denture. The results were compared with those of a conventional heat polymerized acrylic resin (Paladent 20) and a thermoplastic polyamide resin (Biotone). The failure sites were examined by scanning electron microscopy to evaluate the mode of failure. As results, the bond strength of reline resins to a thermoplastic acrylic resin was similar to the value of a conventional heat polymerized acrylic resin. However, thermoplastic polyamide resin showed the lowest value. The results of this study indicated that a thermoplastic acrylic resin for non metal clasps denture allows chairside reline and repair. It was also found that the light-polymerized reline resin had better bond strength than the autopolymerizing reline resin in relining for a conventional heat polymerized acrylic resin and a thermoplastic acrylic resin.

  13. Environmentally friendly properties of vegetable oil methyl esters

    Directory of Open Access Journals (Sweden)

    Gateau Paul

    2005-07-01

    Full Text Available Measurements were carried out on Vegetable Oil Methyl Esters (VOME or FAME answering the most recent specifications. The products tested are RME (Rapeseed oil Methyl Ester, ERME (Erucic Rapeseed oil Methyl Esters, SME (Sunflower oil Methyl Esters, and HOSME (High Oleic Sunflower oil Methyl Esters. They contain more than 99.5% of fatty acid mono esters. The compositions are given. VOME are not volatile and they are not easily flammable. They are not soluble in water and they are biodegradable. According to the methods implemented for the determination of the German classification of substances hazardous to waters WGK, they are not toxic on mammals and unlike diesel fuel they are not toxic on fish, daphnia, algae and bacteria. The RME is not either toxic for shrimps. According to tests on rabbits, RME and SME are not irritating for the skin and the eyes. VOME display particularly attractive environmental properties.

  14. Resin selection criteria for tough composite structures

    Science.gov (United States)

    Chamis, C. C.; Smith, G. T.

    1983-01-01

    Resin selection criteria are derived using a structured methodology consisting of an upward integrated mechanistic theory and its inverse (top-down structured theory). These criteria are expressed in a "criteria selection space" which are used to identify resin bulk properties for improved composite "toughness". The resin selection criteria correlate with a variety of experimental data including laminate strength, elevated temperature effects and impact resistance.

  15. Solidifying power station resins and sludges

    International Nuclear Information System (INIS)

    Willis, A.S.D.; Haigh, C.P.

    1984-01-01

    Radioactive ion exchange resins and sludges arise at nuclear power stations from various operations associated with effluent treatment and liquid waste management. As the result of an intensive development programme, the Central Electricity Generating Board (CEGB) has designed a process to convert power station resins and sludges into a shielded, packaged solid monolithic form suitable for final disposal. Research and development, the generic CEGB sludge/resin conditioning plant and the CEGB Active Waste Project are described. (U.K.)

  16. Volumetric polymerization shrinkage of contemporary composite resins

    OpenAIRE

    Nagem Filho, Halim; Nagem, Haline Drumond; Francisconi, Paulo Afonso Silveira; Franco, Eduardo Batista; Mondelli, Rafael Francisco Lia; Coutinho, Kennedy Queiroz

    2007-01-01

    The polymerization shrinkage of composite resins may affect negatively the clinical outcome of the restoration. Extensive research has been carried out to develop new formulations of composite resins in order to provide good handling characteristics and some dimensional stability during polymerization. The purpose of this study was to analyze, in vitro, the magnitude of the volumetric polymerization shrinkage of 7 contemporary composite resins (Definite, Suprafill, SureFil, Filtek Z250, Fill ...

  17. Porous Ceramic Spheres from Ion Exchange Resin

    Science.gov (United States)

    Dynys, Fred

    2005-01-01

    A commercial cation ion exchange resin, cross-linked polystyrene, has been successfully used as a template to fabricate 20 to 50 micron porous ceramic spheres. Ion exchange resins have dual template capabilities. Pore architecture of the ceramic spheres can be altered by changing the template pattern. Templating can be achieved by utilizing the internal porous structure or the external surface of the resin beads. Synthesis methods and chemical/physical characteristics of the ceramic spheres will be reported.

  18. Bond strength of resin-resin interfaces contaminated with saliva and submitted to different surface treatments

    OpenAIRE

    Furuse, Adilson Yoshio; Cunha, Leonardo Fernandes da; Benetti, Ana Raquel; Mondelli, José

    2007-01-01

    The purpose of this study was to investigate the effect of different surface treatments on shear bond strength of saliva-contaminated resin-resin interfaces. Flat resin surfaces were fabricated. In the control group, no contamination or surface treatment was performed. The resin surfaces of the experimental groups were contaminated with saliva and air-dried, and then submitted to: (G1) rinsing with water and drying; (G2) application of an adhesive system; (G3) rinsing and drying, abrasion wit...

  19. Mutagenic activity of phthalate esters in bacterial liquid suspension assays.

    OpenAIRE

    Seed, J L

    1982-01-01

    The mutagenic activities of several phthalate esters have been evaluated in an 8-azaguanine resistance assay in Salmonella typhimurium. Three phthalate esters were found to be mutagenic: dimethyl phthalate, diethyl phthalate and di-n-butyl phthalate. A number of other phthalate esters were not found to be mutagenic, including di(2-ethylhexyl) phthalate, di-n-octyl phthalate, diallyl phthalate, diisobutyl phthalate and diisodecyl phthalate. A metabolite of di(2-ethylhexyl) phthalate, 2-ethylhe...

  20. Parameters affecting ethyl ester production by Saccharomyces cerevisiae during fermentation.

    Science.gov (United States)

    Saerens, S M G; Delvaux, F; Verstrepen, K J; Van Dijck, P; Thevelein, J M; Delvaux, F R

    2008-01-01

    Volatile esters are responsible for the fruity character of fermented beverages and thus constitute a vital group of aromatic compounds in beer and wine. Many fermentation parameters are known to affect volatile ester production. In order to obtain insight into the production of ethyl esters during fermentation, we investigated the influence of several fermentation variables. A higher level of unsaturated fatty acids in the fermentation medium resulted in a general decrease in ethyl ester production. On the other hand, a higher fermentation temperature resulted in greater ethyl octanoate and decanoate production, while a higher carbon or nitrogen content of the fermentation medium resulted in only moderate changes in ethyl ester production. Analysis of the expression of the ethyl ester biosynthesis genes EEB1 and EHT1 after addition of medium-chain fatty acid precursors suggested that the expression level is not the limiting factor for ethyl ester production, as opposed to acetate ester production. Together with the previous demonstration that provision of medium-chain fatty acids, which are the substrates for ethyl ester formation, to the fermentation medium causes a strong increase in the formation of the corresponding ethyl esters, this result further supports the hypothesis that precursor availability has an important role in ethyl ester production. We concluded that, at least in our fermentation conditions and with our yeast strain, the fatty acid precursor level rather than the activity of the biosynthetic enzymes is the major limiting factor for ethyl ester production. The expression level and activity of the fatty acid biosynthetic enzymes therefore appear to be prime targets for flavor modification by alteration of process parameters or through strain selection.

  1. Isolation and identification of an ester from a crude oil

    Science.gov (United States)

    Phillips, H.F.; Breger, I.A.

    1958-01-01

    A dioctylphthalate has been isolated from a crude oil by means of adsorption column chromatography. The ester was identified by means of elemental analysis, refractive index, and its infra-red absorption spectrum. Saponification of the isolate and examination of the resultant alcohol by means of infrared absorption spectra led to the conclusion that the ester is a branched chain dioctylphthalate. This is the first reported occurrence of an ester in crude petroleum. ?? 1958.

  2. Novel silica-based ion exchange resin

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    Eichrom`s highly successful Diphonixo resin resembles a conventional ion exchange resin in its use of sulfonic acid ligands on a styrene- divinylbenzene matrix. Diphonix resin exhibits rapid exchange kinetics that allow economical operation of ion exchange systems. Unlike conventional resins, Diphonix resin contains chelating ligands that are diphosphonic acid groups that recognize and remove the targeted metals and reject the more common elements such as sodium, calcium and magnesium. This latter property makes Diphonix ideal for many industrial scale applications, including those involving waste treatment. For treatment of low-level, transuranic (TRU) and high- level radioactive wastes, Diphonix`s polystyrene backbone hinders its application due to radiolytic stability of the carbon-hydrogen bonds and lack of compatibility with expected vitrification schemes. Polystyrene-based Diphonix is approximately 60% carbon- hydrogen. In response to an identified need within the Department of Energy for a resin with the positive attributes of Diphonix that also exhibits greater radiolytic stability and final waste form compatibility, Eichrom has successfully developed a new, silica-based resin version of Diphonix. Target application for this new resin is for use in environmental restoration and waste management situations involving the processing of low-level, transuranic and high-level radioactive wastes. The resin can also be used for processing liquid mixed waste (waste that contains low level radioactivity and hazardous constituents) including mixed wastes contaminated with organic compounds. Silica-based Diphonix is only 10% carbon-hydrogen, with the bulk of the matrix silica.

  3. Microbiological study of water-softener resins.

    Science.gov (United States)

    Stamm, J M; Engelhard, W E; Parsons, J E

    1969-09-01

    Microbial identification using effluents backflushed from exhausted urban and rural tank resins and cleaned resins containing the sulfonated copolymer of styrene and divinylbenzene (SDB) were completed, along with microbial assessment of the concentrated stock salt brine. Forty-four different bacterial and fungal genera were identified. Extensive biochemical and animal virulence tests completed on one of the six bacterial salt brine isolates indicated a pathogenic staphylococcal strain. The retention of Staphylococcus aureus, a Flavobacterium sp, and Escherichia coli B bacteriophage was demonstrated both by using the nonexhausted sodium-regenerated resin and by using the same resin exchanged with different mono-, di-, and trivalent cations. Effluent counts completed after bacterial seepage through the resins indicated the Pb(++) exchanged resin removed 55% of the bacteria; Na(+), Fe(++), and Al(+++) removed 31 to 36% and Ca(++) and Cu(++) removed about 10 to 15%. Seventy per cent or more of the bacteriophage was removed by Fe(++), Cu(++), and Al(+++), whereas the Ca(++) and Na(++) cations removed 25 to 31%. Over a 77-day period, nonsterile tap water was passed through bacterial seeded and uninoculated SDB (Na) resin columns. Effluent and resin elution counts demonstrated the growth and survival of 2 different bacteria per column. Increased bacterial retention, survival, and multiplication occurred concomitantly with accumulation of organic and inorganic materials and the Ca(++) and Mg(++) cations from the tap water. Furthermore, microbial elution from resin particles taken from column depths of 1, 8, and 16 cm indicated a bacterial diminution with increasing depths.

  4. Heat-cured Acrylic Resin versus Light-activated Resin: A Patient ...

    African Journals Online (AJOL)

    Context: Although light-activated resins (Eclipse) have been reported to possess superior physical and mechanical properties compared with the heat-cured acrylic resins (Lucitone-199), a few studies have compared overdentures with a locator attachment constructed from heat-cured acrylic resins with those constructed ...

  5. Biotransformation--XXXIV. Metabolism of testosterone esters in fungi cultures.

    Science.gov (United States)

    Brzezowska, E; Dmochowska-Gładysz, J; Kołek, T; Nobilec, E

    1993-08-01

    Seven esters of testosterone: acetate, propionate, enanthate, caprate, undecanoate, isobutyrate and isocaproate (some of them are used as drugs) were transformed by microorganisms: Absidia coerulea, Acremonium roseum, Aphanocladium album and Rhodotorula mucilaginosa to obtain some information about their metabolism. It was observed that the presence and structure of the acyl group mainly influenced the degree of transformation. The first step of the reaction was probably hydrolysis of ester, followed by testosterone transformation. Only the branched chain esters were transformed by R. mucilaginosa without hydrolysis of the ester bond.

  6. A novel thermooxidatively stable poly(ester-imide-benzoxazole)

    Energy Technology Data Exchange (ETDEWEB)

    Sundar, R.A.; Mathias, L.J. [Univ. of Sothern Mississippi, Hattiesburg, MS (United States)

    1993-12-31

    A poly(ester-amide-imide) was synthesized by the low temperature solution polycondensation of 4-amino-5-hydroxy-N,4{prime}-hydroxyphenyl phthalimide with isophthaloyl chloride. Subsequent thermal cyclodehydration of the poly(ester-amide-imide) at 320{degrees}C in vacuum afforded the poly(ester-imide-benzoxazole). This polymer was only soluble in sulfuric acid. FTIR and NMR spectra confirmed structure. The poly(ester-imide-benzoxazole) had no detectable thermal transitions up to 500{degrees}C in nitrogen, and was reasonably stable in air and nitrogen, with weight retentions of 95% at 500{degrees}C.

  7. Investigation of bifunctional ester additives for methanol-gasoline system

    International Nuclear Information System (INIS)

    Zhang, J.; Yang, C.; Tang, Y.; Du, Q.; Song, N.; Zhang, Z.

    2014-01-01

    To explore new and multifunctional additives for methanol-gasoline, tartaric ester were synthesized and screened as phase stabilizer and saturation vapor pressure depressor for methanol-gasoline. The effect of the esters structure on the efficiency was discussed. The results show that the stabilities of the blends depend on the length of the glycolic esters alkoxy group. In addition, the tartaric esters also can depress the saturation vapor pressure of methanol-gasoline effectively in M15. Effect of the structure on the efficiency was also discussed. (author)

  8. Tandem transformation of glycerol to esters.

    Science.gov (United States)

    Sotenko, Maria V; Rebroš, Martin; Sans, Victor S; Loponov, Konstantin N; Davidson, Matthew G; Stephens, Gill; Lapkin, Alexei A

    2012-12-31

    Tandem transformation of glycerol via microbial fermentation and enzymatic esterification is presented. The reaction can be performed with purified waste glycerol from biodiesel production in a continuous mode, combining continuous fermentation with membrane-supported enzymatic esterification. Continuous anaerobic fermentation was optimized resulting in the productivity of 2.4 g L⁻¹ h⁻¹ of 1,3-propanediol. Biphasic esterification of 1,3-propanediol was optimized to achieve ester yield of up to 75%. A hollow fibre membrane contactor with immobilized Rhizomucor miehei lipase was demonstrated for the continuous tandem fermentation-esterification process. Copyright © 2012 Elsevier B.V. All rights reserved.

  9. Comparison of Cashew Nut Shell Liquid (CNS ) Resin with ...

    African Journals Online (AJOL)

    synthetic) resin. Compressive and tensile strength tests conducted proved that composites developed with cashew nut shell liquid (CNSL) resin were comparable to those developed with polyester resin. In the results, CNSL has an ultimate ...

  10. Palladium-catalysed arylation of acetoacetate esters to yield 2-arylacetic acid esters

    CSIR Research Space (South Africa)

    Zeevaart, JG

    2004-05-24

    Full Text Available The coupling reaction between ethyl acetoacetate and a number of aryl halides in the presence of palladium acetate, a bulky and electron rich phosphine and K3PO4 is described. The arylated acetoacetate ester is de-acylated under the reaction...

  11. Resin composite for sealing and its use in a solar cell. Fushiyo jushi soseibutsu oyobi sore wo mochiita taiyo denchi

    Energy Technology Data Exchange (ETDEWEB)

    Toma, H.; Mimura, T.; Takehara, N.

    1994-01-28

    This invention presents resin composites for sealing of a solar cell composed of a hardening resin and a thermoplastic resin which has a number average molecular weight larger than that of the hardening resin and is soluble in the hardening resin, and the invention affords a solar cell to endure a long-term stable operation and to give a good performance. The hardening resin includes unsaturated polyester resin, phenolic resin, alkyd resin, unsaturated acrylic resin, epoxy resin, polyurethane resin, melamine resin, diallyl phthalate resin, their oligomers and their modifications. The thermoplastic resin includes saturated polyester resin, phenolic resin, acrylic resin, styrene resin, epoxy resin, polyurethane resin, polyvinyl acetate resin, polyvinyl chloride resin, polyvinyl alcohol resin, polyacetal resin, their modifications and their copolymer resin. 2 figs., 3 tabs.

  12. Curing kinetics of alkyd/melamine resin mixtures

    OpenAIRE

    Jovičić Mirjana C.; Radičević Radmila Ž.

    2009-01-01

    Alkyd resins are the most popular and useful synthetic resins applied as the binder in protective coatings. Frequently they are not used alone but are modified with other synthetic resins in the manufacture of the coatings. An alkyd/melamine resin mixture is the usual composition for the preparation of coating called 'baking enamel' and it is cured through functional groups of resins at high temperatures. In this paper, curing kinetics of alkyd resins based on castor oil and dehydrated castor...

  13. Sensomics analysis of key bitter compounds in the hard resin of hops (Humulus lupulus L.) and their contribution to the bitter profile of Pilsner-type beer.

    Science.gov (United States)

    Dresel, Michael; Dunkel, Andreas; Hofmann, Thomas

    2015-04-08

    Recent brewing trials indicated the occurrence of valuable bitter compounds in the hard resin fraction of hop. Aiming at the discovery of these compounds, hop's ε-resin was separated by means of a sensory guided fractionation approach and the key taste molecules were identified by means of UV/vis, LC-TOF-MS, and 1D/2D-NMR studies as well as synthetic experiments. Besides a series of literature known xanthohumol derivatives, multifidol glucosides, flavon-3-on glycosides, and p-coumaric acid esters, a total of 11 bitter tastants are reported for the first time, namely, 1",2"-dihydroxanthohumol F, 4'-hydroxytunicatachalcone, isoxantholupon, 1-methoxy-4-prenylphloroglucinol, dihydrocyclohumulohydrochinone, xanthohumols M, N, and P, and isoxanthohumols M, N, and P, respectively. Human sensory analysis revealed low bitter recognition threshold concentrations ranging from 5 (co-multifidol glucopyranoside) to 198 μmol/L (trans-p-coumaric acid ethyl ester) depending on their chemical structure. For the first time, LC-MS/MS quantitation of these taste compounds in Pilsner-type beer, followed by taste re-engineering experiments, revealed the additive contribution of iso-α-acids and the identified hard resin components to be truly necessary and sufficient for constructing the authentic bitter percept of beer. Finally, brewing trails using the ε-resin as the only hop source impressively demonstrated the possibility to produce beverages strongly enriched with prenylated hop flavonoids.

  14. Neutral Lipid Biosynthesis in Engineered Escherichia coli: Jojoba Oil-Like Wax Esters and Fatty Acid Butyl Esters

    OpenAIRE

    Kalscheuer, Rainer; Stöveken, Tim; Luftmann, Heinrich; Malkus, Ursula; Reichelt, Rudolf; Steinbüchel, Alexander

    2006-01-01

    Wax esters are esters of long-chain fatty acids and long-chain fatty alcohols which are of considerable commercial importance and are produced on a scale of 3 million tons per year. The oil from the jojoba plant (Simmondsia chinensis) is the main biological source of wax esters. Although it has a multitude of potential applications, the use of jojoba oil is restricted, due to its high price. In this study, we describe the establishment of heterologous wax ester biosynthesis in a recombinant E...

  15. Input to Resin Column Structural Analysis if Autocatalytic Resin Reaction Occurs in HB-Line Phase II

    Energy Technology Data Exchange (ETDEWEB)

    Hallman, D.F.

    2001-07-10

    Solutions of plutonium in nitric acid are purified and concentrated using anion resin prior to precipitation. There have been instances of resin column explosions caused by autocatalytic reactions of anion resins in nitric acid within the DOE complex

  16. Gold Loading on Ion Exchange Resins in Non-Ammoniacal Resin-Solution Systems

    Directory of Open Access Journals (Sweden)

    Abrar Muslim

    2010-12-01

    Full Text Available The loading of gold using strong base anion exchange resin in non-ammoniac resin-solution (NARS systems has been studied. The loading of gold onto ion exchange resins is affected by polythionate concentration, and trithionate can be used as the baseline in the system. The results also show that resin capacity on gold loading increases due to the increase in the equilibrium thiosulfate concentration in the NARS system. Gold loading performances show the need of optimization the equilibrium concentrations of thiosulfate in the NARS system. Keywords: equilibrium, gold loading, resin capacity, thiosulfate, trithionate

  17. Polyimide Resins Resist Extreme Temperatures

    Science.gov (United States)

    2009-01-01

    Spacecraft and aerospace engines share a common threat: high temperature. The temperatures experienced during atmospheric reentry can reach over 2,000 F, and the temperatures in rocket engines can reach well over 5,000 F. To combat the high temperatures in aerospace applications, Dr. Ruth Pater of Langley Research Center developed RP-46, a polyimide resin capable of withstanding the most brutal temperatures. The composite material can push the service temperature to the limits of organic materials. Designed as an environmentally friendly alternative to other high-temperature resins, the RP-46 polyimide resin system was awarded a 1992 "R&D 100" award, named a "2001 NASA Technology of the Year," and later, due to its success as a spinoff technology, "2004 NASA Commercial Invention of the Year." The technology s commercial success also led to its winning the Langley s "Paul F. Holloway Technology Transfer Award" as well as "Richard T. Whitcom Aerospace Technology Transfer Award" both for 2004. RP-46 is relatively inexpensive and it can be readily processed for use as an adhesive, composite, resin molding, coating, foam, or film. Its composite materials can be used in temperatures ranging from minus 150 F to 2,300 F. No other organic materials are known to be capable of such wide range and extreme high-temperature applications. In addition to answering the call for environmentally conscious high-temperature materials, RP-46 provides a slew of additional advantages: It is extremely lightweight (less than half the weight of aluminum), chemical and moisture resistant, strong, and flexible. Pater also developed a similar technology, RP-50, using many of the same methods she used with RP-46, and very similar in composition to RP-46 in terms of its thermal capacity and chemical construction, but it has different applications, as this material is a coating as opposed to a buildable composite. A NASA license for use of this material outside of the Space Agency as well as

  18. The solidification of spent resin

    International Nuclear Information System (INIS)

    Shiao, S. J.; Tsai, C. M.; Shyu, Y. H.

    1991-01-01

    A quasi-steady apparatus was applied to measure the thermal conductivity of solids ranging in size for 0.3 to 200 L, and temperature distributions in the solids were recorded during the curing, and theoretical equation for conduction in a cylindrical form with uniform energy generation was established to define the thermal state of reaction. The heat of reaction calculated from the theoretical equation with experimental values for the maximum temperature and thermal conductivity agrees very well with the data reported. The relationships among heat of reaction and amount of curing agent, retardant, loading of spent resin, and water were established

  19. Antifungal activity against Botrytis cinerea of labdane-type diterpenoids isolated from the resinous exudate of Haplopappus velutinus Remy (Asteraceae).

    Science.gov (United States)

    Echeverría, Javier; González-Teuber, Marcia; Urzúa, Alejandro

    2018-02-25

    Two labdane diterpenoids were isolated, from the resinous exudate of Haplopappus velutinus Remy (Asteraceae); the main compound was identified as 7,13-(E)-labdadien-15,18-dioic-acid-18-methyl ester (1) and the minor compound identified as 7-labden-15,18-dioic-acid-18-methyl ester (2). Their structures were obtained using FTIR, MS, HRMS and NMR data: 1D NMR ( 1 H, 13 C and DEPT-135), 2D homonuclear NMR (COSY and NOESY) and heteronuclear NMR (HSQC and HMBC). The trans stereochemistry of the decalin moiety of compounds 1 and 2 was established through NOESY experiments of the reduction product of 1; 7-labden-15,18-diol (1a). Diterpenoids 1 and 1a are described for the first time and showed antifungal activity, inhibiting approximately 40% mycelial growth of Botrytis cinerea.

  20. Comparison of Cashew Nut Shell Liquid (CNS Resin with Polyester Resin in Composite Development

    Directory of Open Access Journals (Sweden)

    C. C. Ugoamadi

    2013-12-01

    Full Text Available Natural resins can compete effectively with the synthetic ones in composite development. In this research, cashew nuts were picked and processed for the extraction of the resin content. The resin (natural resin so obtained was mixed with cobalt amine (accelerator, methyl ethyl ketone peroxide (catalyst to develop two sets of composite specimens – specimens without fibres and specimens reinforced with glass fibres. This method of sample specimen development was repeated with polyester (synthetic resin. Compressive and tensile strength tests conducted proved that composites developed with cashew nut shell liquid (CNSL resin were comparable to those developed with polyester resin. In the results, CNSL has an ultimate compressive strength of 55MPa compared to that of polyester resin with an ultimate strength of 68MPa. The result of tensile strength proved cashew nut shell liquid resin (with ultimate strength of 44MPa to be better than polyester resin with 39MPa as ultimate tensile strength. This means that natural resins could be a better substitute for the synthetic ones when the required quantities of fibers (reinforcements and fillers are used in the fibre-reinforced plastic composite developments.

  1. Bond strength of resin-resin interfaces contaminated with saliva and submitted to different surface treatments.

    Science.gov (United States)

    Furuse, Adilson Yoshio; da Cunha, Leonardo Fernandes; Benetti, Ana Raquel; Mondelli, José

    2007-12-01

    The purpose of this study was to investigate the effect of different surface treatments on shear bond strength of saliva-contaminated resin-resin interfaces. Flat resin surfaces were fabricated. In the control group, no contamination or surface treatment was performed. The resin surfaces of the experimental groups were contaminated with saliva and air-dried, and then submitted to: (G1) rinsing with water and drying; (G2) application of an adhesive system; (G3) rinsing and drying, abrasion with finishing disks, etching and application of adhesive system; (G4) rinsing and drying, etching, application of silane and adhesive system. Resin cylinders were placed over the treated surfaces. The specimens were stored in water or ethanol. Shear bond strength tests were performed and the mode of failure was evaluated. Data were submitted to two-way ANOVA and Dunnett T3 test. Contamination of resin-resin interfaces with saliva significantly reduced shear strength, especially after prolonged storage (presin increments.

  2. resin as polymer-supported synthesis support

    Indian Academy of Sciences (India)

    Administrator

    dichloro-5,6-dicyano- benzoqunone ... ports used most widely in SPOS are Merrifield resin .... (2 × 10 mL). The resin was dried at 50°C for one hour to give white beads. IR (KBr): 3108, 3312 cm–1. 1H-NMR (500 MHz, CDCl3): δ 7⋅13 (br s, PS), 7⋅01.

  3. [Delayed asthma bronchiale due to epoxy resin].

    Science.gov (United States)

    Authried, Georg; Al-Asadi, Haifaa; Møller, Ulla; Sherson, David Lee

    2013-10-28

    Epoxy resin is a low molecular weight agent, which can cause both acute and delayed allergic reactions. However, it is known causing skin reactions with direct or airborne contact. Rarely it can cause airway reactions like asthma bronchiale. We describe a case of a windmill worker who developed delayed asthma bronchiale due to airborne contact with epoxy resin.

  4. Epoxidation of linseed oil-Alkyd resins

    International Nuclear Information System (INIS)

    Motawie, A.M.; Ismail, E.A.; Mazroua, A.M.; Abd EI Aziem, M.S.; Ramadan, A.M.

    2004-01-01

    Three types of different linseed oil-alkyd resin ( Alk (I), Alk (II), and Alk (III) ) were prepared with the calculated amounts of mono glycerides and adipic acid (1:1, 1:2, and 2:1 Eq.Wt) respectively via monoglyceride method. The obtained alkyd resins were epoxidized via reaction with the calculated quantities of peracetic acid, which was prepared by the reaction of acetic anhydride with H 2 O 2 . Epoxidation occurred with the ratio (1: 1, 1 :3, and 1:6 Eq. Wt) of alkyd to peracetic acid. The effect of reaction time on the epoxy group content was measured during the epoxidation process. The prepared alkyd resins were analyzed by IR and H 1 NMR. The metal coated film properties of epoxidized alkyd resins were compared with those of unmodified alkyd resins. It was observed that the coating films of epoxidized alkyd resins have better in drying properties, hardness, adhesion, impact and flexibility than those of un epoxidized alkyd resins. The flammability properties of the paper coated films for the prepared brominated epoxidized alkyd resins were found to be fire retardant

  5. Facile synthesis of hypercrosslinked resins via chloromethylation ...

    Indian Academy of Sciences (India)

    A sort of non-polystyrene type hypercrosslinked resin was firstly synthesized through chloromethylation of simple aryl molecules (benzene, toluene, naphthalene, diphenyl), succedent continuous Friedel–Crafts alkylation polymerization and post-crosslinking reaction. The chemical and porous structures of these novel resins ...

  6. Physical Properties of Synthetic Resin Materials

    Science.gov (United States)

    Fishbein, Meyer

    1939-01-01

    A study was made to determine the physical properties of synthetic resins having paper, canvas, and linen reinforcements, and of laminated wood impregnated with a resin varnish. The results show that commercial resins have moduli of elasticity that are too low for structural considerations. Nevertheless, there do exist plastics that have favorable mechanical properties and, with further development, it should be possible to produce resin products that compare favorably with the light-metal alloys. The results obtained from tests on Compound 1840, resin-impregnated wood, show that this material can stand on its own merit by virtue of a compressive strength four times that of the natural wood. This increase in compressive strength was accomplished with an increase of density to a value slightly below three times the normal value and corrected one of the most serious defects of the natural product.

  7. Electrodialytic decontamination of spent ion exchange resins

    International Nuclear Information System (INIS)

    Nott, B.R.

    1982-01-01

    Development of a novel electrodialytic decontamination process for the selective removal of radioactive Cs from spent ion exchange resins containing large amounts of Li is described. The process involves passage of a dc electric current through a bed of the spent ion exchange resin in a specially designed electrodialytic cell. The radiocesium so removed from a volume of the spent resin is concentrated onto a much smaller volume of a Cs selective sorbent to achieve a significant radioactive waste volume reduction. Technical feasibility of the electrodialytic resin decontamination process has been demonstrated on a bench scale with a batch of simulated spent ion exchange resin and using potassium cobalt ferrocyanide as the Cs selective sorbent. A volume reduction factor between 10 and 17 has been estimated. The process appears to be economically attractive. Improvements in process economics can be expected from optimization of the process. Other possible applications of the EDRD process have been identified

  8. Embedding of reactor wastes in plastic resins

    International Nuclear Information System (INIS)

    1979-01-01

    STEAG Kernenergie GmbH is so far the only firm commercially to condition radioactive bead ion exchange resins by embedding in polystyrene resins. The objective of the work reported here was to study and develop methods for immobilization of other reactor wastes in plastic resins. Comparison studies on high quality cement however showed favourable results for cement with respect to process safety and economy. For this reason STEAG interrupted its work in the field of resin embedding after about one year. The work carried out during this period is surveyed in this report, which includes a comprehensive literature study on reactor wastes and their solidification in plastic resins as well as on regulations with regard to radioactive waste disposal in the member states of the European Communities

  9. Disinfection of denture base acrylic resin.

    Science.gov (United States)

    Lin, J J; Cameron, S M; Runyan, D A; Craft, D W

    1999-02-01

    During repair or adjustments of acrylic resin removable complete and partial dentures, particles of the acrylic resin from the interior of the prosthesis may expose dental personnel to microbial health hazards if the prosthesis has not been thoroughly disinfected. This study investigates the efficacy of a commercially prepared microbial disinfectant (Alcide) on the external and internal surfaces of acrylic resins. Four groups of acrylic resin were incubated in an experimental model to simulate the oral environment over time. Specimens were treated in 2 groups, disinfected and not disinfected, and then further grouped by breaking and not breaking. Analysis was performed with microbial colony counts, SEM, and statistical analyses. Viable microorganisms still remain on the internal and external surfaces of treated resins. Chlorine dioxide reduces, but does not eliminate, viable microorganisms on these dental prostheses.

  10. Preparation of esters of gallic acid with higher primary alcohols

    NARCIS (Netherlands)

    Kerk, G.J.M. van der; Verbeek, J.H.; Cleton, J.C.F.

    1951-01-01

    The esters of gallic acid and higher primary alcohols, especially fatty alcohols, have recently gained considerable interest as possible antioxidants for fats. Two independent methods for the preparation of these esters are described. In the first method the hitherto unknown compound galloyl

  11. Production of both esters and biogas from Mexican poppy

    African Journals Online (AJOL)

    AJL

    esters, use oils of plant origin like vegetable oils and tree born oil seeds are ... Usage of ester will allow a balance to be sought between agriculture .... Sci. Technol. Plastic tube. Stopper. Glass bottle. (1 liter capacity). Rubber cap. Gas collector. Digester. Displaced water. Figure 1. Reactor design (see experimental set up).

  12. Alternative Production of Fatty Acid Methyl Esters from Triglycerides ...

    African Journals Online (AJOL)

    The catalysts activity was tested in thermocatalytic cracking of triglyceride; a direct conversion process for fatty acid methyl esters (biodiesel). The SZ1 not only exhibited higher conversion of triglycerides but higher fatty acid methyl esters (FAMEs) yields of approximately 59% after 3h as compared to SZ2 (32%). In addition ...

  13. Effect of Sucrose Esters on the Physicochemical Properties of Wheat ...

    African Journals Online (AJOL)

    HP

    modified starch were analyzed by Fourier transform infrared spectroscopy (FITR), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). Results: The properties of wheat starch changed greatly by adding different sucrose esters to their structures. Starch containing 0.30 % sucrose esters had the ...

  14. Phthalic acid esters found in municipal organic waste

    DEFF Research Database (Denmark)

    Hartmann, Hinrich; Ahring, Birgitte Kiær

    2003-01-01

    Contamination of the organic fraction of municipal solid waste (OFMSW) with xenobiotic compounds and their fate during anaerobic digestion was investigated. The phthalic acid ester di-(2- ethylhexyl)phthalate (DEHP) was identified as the main contaminant in OFMSW in concentrations more than half...... matter with high biogas yields and efficient reduction of the phthalic acid ester contamination....

  15. Determination of Phthalate Esters in the Aquatic Environment ...

    African Journals Online (AJOL)

    The use of solid phase extraction and capillary GLC provides the basis for selective determination of phthalate ester plasticizers in rivers and marine water samples. Of the several solvent ratios (methanol in dichloromethane) that were tried for selective elution of phthalate esters from the C18 solid phase glass catridge, the ...

  16. Protective effect of glucosamine cyclohexyl ester on osteoarthritis in ...

    African Journals Online (AJOL)

    Purpose: To investigate the therapeutic effect of glucosamine cyclohexyl ester on osteoarthritis (OA) in a rat model. Methods: Reverse transcription-quantitative polymerase chain reaction (RT-qPCR) and western blot assays were used to analyze the effect of glucosamine cyclohexyl ester on changes in mRNA and protein ...

  17. Effect of Sucrose Esters on the Physicochemical Properties of Wheat ...

    African Journals Online (AJOL)

    HP

    International Pharmaceutical Abstract, Chemical Abstracts, Embase, Index Copernicus, EBSCO, African Index. Medicus, JournalSeek .... Table 1: Rapid visco-analyzer parameters for wheat starch modified with sucrose esters. Content of sucrose esters δ%ε. Peak. (cP). Trough. (cP). Breakdown. (cP). Final. (cP). Setback.

  18. Distribution of phthalate esters in underground water from power ...

    African Journals Online (AJOL)

    This study investigates the distribution of phthalateacid esters (PAEs) in groundwater from some power stations in Delta State. Groundwater samples were collected from eight power transmission and distribution stations. Concentrations (μg/L) of six phthalate acid esters compounds in the groundwater ranged from ...

  19. Protective effect of glucosamine cyclohexyl ester on osteoarthritis in ...

    African Journals Online (AJOL)

    Purpose: To investigate the therapeutic effect of glucosamine cyclohexyl ester on osteoarthritis (OA) in a rat model. Methods: Reverse transcription-quantitative polymerase chain reaction (RT-qPCR) and western blot assays were used to analyze the effect of glucosamine cyclohexyl ester on changes in mRNA and.

  20. Two cases of occupational allergic contact dermatitis from a cycloaliphatic epoxy resin in a neat oil: Case Report

    Science.gov (United States)

    Jensen, Charlotte D; Andersen, Klaus E

    2003-01-01

    Background Metal-working fluids contain complex mixtures of chemicals and metal workers constitute a potential risk group for the development of allergic contact dermatitis. Case presentation Two metal workers developed allergic contact dermatitis on the hands and lower arms from exposure to a neat oil used in metal processing. Patch testing revealed that the relevant contact allergen was a cycloaliphatic epoxy resin, 1,2-cyclohexanedicarboxylic acid, bis(oxiranylmethyl) ester, added to the oil as a stabilizer. None of the patients had positive reactions to the bisphenol A-based epoxy resin in the standard series. Conclusions These cases emphasize that well-known contact allergens may show up from unexpected sources of exposure. Further, it can be a long-lasting, laborious process to detect an occupational contact allergen and cooperation from the patient and the manufacturer of the sensitizing product is essential. PMID:12685935

  1. Rapid NIR determination of alkyl esters in virgin olive oil

    International Nuclear Information System (INIS)

    Cayuela, J.A.

    2017-01-01

    The regulation of The European Union for olive oil and olive pomace established the limit of 35 mg·kg-1 for fatty acids ethyl ester contents in extra virgin olive oils, from grinding seasons after 2016. In this work, predictive models have been established for measuring fatty acid ethyl and methyl esters and to measure the total fatty acid alkyl esters based on near infrared spectroscopy (NIRS), and used successfully for this purpose. The correlation coefficients from the external validation exercises carried out with these predictive models ranged from 0.84 to 0.91. Different classification tests using the same models for the thresholds 35 mg·kg-1 for fatty acid ethyl esters and 75 mg·kg-1 for fatty acid alkyl esters provided success percentages from 75.0% to 95.2%. [es

  2. Continuous biodiesel production in a fixed bed reactor packed with anion-exchange resin as heterogeneous catalyst.

    Science.gov (United States)

    Ren, Yanbiao; He, Benqiao; Yan, Feng; Wang, Hong; Cheng, Yu; Lin, Ligang; Feng, Yaohui; Li, Jianxin

    2012-06-01

    A continuous biodiesel production from the transesterification of soybean oil with methanol was investigated in a fixed bed reactor packed with D261 anion-exchange resin as a heterogeneous catalyst. The conversion to biodiesel achieved 95.2% within a residence time 56 min under the conditions: reaction temperature of 323.15K, n-hexane/soybean oil weight rate of 0.5, methanol/soybean oil molar ratio of 9:1 and feed flow rate of 1.2 ml/min. The resin can be regenerated in-situ and restored to the original activity to achieve continuous production after the resin deactivation. The product obtained was mainly composed of methyl esters. No glycerol in the product was detected due to the resin adsorbing glycerol in the fixed bed, which solved the issue of glycerol separation from biodiesel. It is believed that the fixed bed reactor with D261 has a potential commercial application in the transesterification of triglyceride. Copyright © 2011 Elsevier Ltd. All rights reserved.

  3. Tensile mechanical behavior and fracture toughness of MWCNT and DWCNT modified vinyl-ester/polyester hybrid nanocomposites produced by 3-roll milling

    Energy Technology Data Exchange (ETDEWEB)

    Seyhan, A. Tugrul [Department of Materials Science and Engineering, Anadolu University (Australia), Iki Eylul Campus, 26550 Eskisehir (Turkey); Tanoglu, Metin, E-mail: metintanoglu@iyte.edu.tr [Izmir Institute of Technology (IZTECH), Mechanical Engineering Department, Gulbahce Campus 35437, Izmir (Turkey); Schulte, Karl [Technicshe Universitat Hamburg-Harburg (TUHH), Polymer Composites Section, Denickestrasse 15, D-21073 Hamburg (Germany)

    2009-10-15

    This study aims to investigate the tensile mechanical behavior and fracture toughness of vinyl-ester/polyester hybrid nanocomposites containing various types of nanofillers, including multi- and double-walled carbon nanotubes with and without amine functional groups (MWCNTs, DWCNTs, MWCNT-NH{sub 2} and DWCNT-NH{sub 2}). To prepare the resin suspensions, very low contents (0.05, 0.1 and 0.3 wt.%) of carbon nanotubes (CNTs) were dispersed within a specially synthesized styrene-free polyester resin, conducting 3-roll milling technique. The collected resin stuff was subsequently blended with vinyl-ester via mechanical stirring to achieve final suspensions prior to polymerization. Nanocomposites containing MWCNTs and MWCNT-NH{sub 2} were found to exhibit higher tensile strength and modulus as well as larger fracture toughness and fracture energy compared to neat hybrid polymer. However, incorporation of similar contents of DWCNTs and DWCNT-NH{sub 2} into the hybrid resin did not reflect the same improvement in the corresponding mechanical properties. Furthermore, experimentally measured elastic moduli of the nanocomposites containing DWCNTs, DWCNT-NH{sub 2}, MWCNTs and MWCNT-NH{sub 2} were fitted to Halphin-Tsai model. Regardless of amine functional groups or content of carbon nanotubes, MWCNT modified nanocomposites exhibited better agreement between the predicted and the measured elastic moduli values compared to nanocomposites with DWCNTs. Furthermore, Transmission Electron Microscopy (TEM) and Scanning Electron Microscopy (SEM) were used to reveal dispersion state of the carbon nanotubes within the hybrid polymer and to examine the CNT induced failure modes that occurred under mechanical loading, respectively. Based on the experimental findings obtained, it was emphasized that the types of CNTs and presence of amine functional groups on the surface of CNTs affects substantially the chemical interactions at the interface, thus tuning the ultimate mechanical

  4. Methods of refining and producing dibasic esters and acids from natural oil feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Snead, Thomas E.; Cohen, Steven A.; Gildon, Demond L.

    2016-06-14

    Methods and systems for making dibasic esters and/or dibasic acids using metathesis are generally disclosed. In some embodiments, the methods comprise reacting a terminal olefin ester with an internal olefin ester in the presence of a metathesis catalyst to form a dibasic ester and/or dibasic acid. In some embodiments, the terminal olefin ester or the internal olefin ester are derived from a renewable feedstock, such as a natural oil feedstock. In some such embodiments, the natural oil feedstock, or a transesterified derivative thereof, is metathesized to make the terminal olefin ester or the internal olefin ester.

  5. Activated sludge degradation of adipic acid esters.

    Science.gov (United States)

    Saeger, V W; Kalley, R G; Hicks, O; Tucker, E S; Mieure, J P

    1976-01-01

    The biodegradability of three aliphatic adipic acid diesters and a 1,3-butylene glycol adipic acid polyester was determined in acclimated, activated sludge systems. Rapid primary biodegradation from 67 to 99+% was observed at 3- and 13-mg/liter feed levels for di-n-hexyl adipate, di(2-ethylhexyl) adipate, and di(heptyl, nonyl) adipate in 24 h. When acclimated, activated sludge microorganisms were employed as the seed for two carbon dioxide evolution procedures, greater than 75% of the theoretical carbon dioxide was evolved for the three diesters and the polyester in a 35-day test period. The essentially complete biodegradation observed in these studies suggests that these esters would not persist when exposed to similar mixed microbial populations in the environment. PMID:1275494

  6. Ketone ester effects on metabolism and transcription.

    Science.gov (United States)

    Veech, Richard L

    2014-10-01

    Ketosis induced by starvation or feeding a ketogenic diet has widespread and often contradictory effects due to the simultaneous elevation of both ketone bodies and free fatty acids. The elevation of ketone bodies increases the energy of ATP hydrolysis by reducing the mitochondrial NAD couple and oxidizing the coenzyme Q couple, thus increasing the redox span between site I and site II. In contrast, metabolism of fatty acids leads to a reduction of both mitochondrial NAD and mitochondrial coenzyme Q causing a decrease in the ΔG of ATP hydrolysis. In contrast, feeding ketone body esters leads to pure ketosis, unaccompanied by elevation of free fatty acids, producing a physiological state not previously seen in nature. The effects of pure ketosis on transcription and upon certain neurodegenerative diseases make approach not only interesting, but of potential therapeutic value.

  7. Evaluation of Resin-Resin Interface in Direct Composite Restoration Repair

    Science.gov (United States)

    Stoleriu, S.; Andrian, S.; Pancu, G.; Nica, I.; Iovan, G.

    2017-06-01

    The aim of this study was to evaluate the resin-resin interface when a universal bonding agent was used in two different strategies in direct restoration repair. Two composite resins (a micro-filled hybrid and a nano-filled hybrid) as old restorations that have to be repair, a universal bonding agent and a micro-filled hybrid composite resin (different then that aged) as new material for repair were chosen for the study. Non-aged samples were used as control and aged samples were used as study groups. The universal bonding agent was applied in etch-and-rinse and in self-etch strategies. The interface between old and new composite resins was evaluated by SEM and the microleakage was assessed by scoring the dye penetration. Very good adaptation of the two different composite resins placed in direct contact in non-aged samples was recorded. No gaps or defects were visible and strong resin-resin contact was observed. After aging, enlargement of resin-resin junction were observed in most of the samples and a increased dye penetration was recorded irrespective of the strategy (etch-and-rinse or self-etch) used for bonding agent application.

  8. Viscosity of aqueous and cyanate ester suspensions containing alumina nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Lawler, Katherine [Iowa State Univ., Ames, IA (United States)

    2009-01-01

    The viscosities of both aqueous and cyanate ester monomer (BECy) based suspensions of alumina nanoparticle were studied. The applications for these suspensions are different: aqueous suspensions of alumina nanoparticles are used in the production of technical ceramics made by slip casting or tape casting, and the BECy based suspensions are being developed for use in an injection-type composite repair resin. In the case of aqueous suspensions, it is advantageous to achieve a high solids content with low viscosity in order to produce a high quality product. The addition of a dispersant is useful so that higher solids content suspensions can be used with lower viscosities. For BECy suspensions, the addition of nanoparticles to the BECy resin is expected to enhance the mechanical properties of the cured composite. The addition of saccharides to aqueous suspensions leads to viscosity reduction. Through DSC measurements it was found that the saccharide molecules formed a solution with water and this resulted in lowering the melting temperature of the free water according to classic freezing point depression. Saccharides also lowered the melting temperature of the bound water, but this followed a different rule. The shear thinning and melting behaviors of the suspensions were used to develop a model based on fractal-type agglomeration. It is believed that the structure of the particle flocs in these suspensions changes with the addition of saccharides which leads to the resultant viscosity decrease. The viscosity of the BECy suspensions increased with solids content, and the viscosity increase was greater than predicted by the classical Einstein equation for dilute suspensions. Instead, the Mooney equation fits the viscosity behavior well from 0-20 vol% solids. The viscosity reduction achieved at high particle loadings by the addition of benzoic acid was also investigated by NMR. It appears that the benzoic acid interacts with the surface of the alumina particle which may

  9. Bond strength of a chairside autopolymerizing reline resin to injection-molded thermoplastic denture base resins.

    Science.gov (United States)

    Hamanaka, Ippei; Shimizu, Hiroshi; Takahashi, Yutaka

    2017-01-01

    This study evaluated the shear bond strength of a chairside autopolymerizing reline resin to injection-molded thermoplastic denture base resins. Four kinds of injection-molded thermoplastic resins (two polyamides, a polyethylene terephthalate copolymer and a polycarbonate) and PMMA, as a control, were tested. The eight types of surface treatment: ((1) no treatment, (2) air abrasion, (3) dichloromethane, (4) ethyl acetate, (5) 4-META/MMA-TBB resin, (6) air abrasion and 4-META/MMA-TBB resin, (7) tribochemical silica coating, and (8) tribochemical silica coating and 4-META/MMA-TBB resin) were applied to each specimen. The chairside autopolymerizing reline resins were bonded to disks of the injection-molded thermoplastic denture base resins. All of the specimens were immersed in water for 4 months and then thermocycled for 10,000 cycles in water between 5 and 55°C. The shear bond strengths were determined. The shear bond strengths of the two polyamides treated using air abrasion, dichloromethane and ethyl acetate and no treatment were exceedingly low. The greatest bond strength was recorded for the polyethylene terephthalate copolymer specimens treated with tribochemical silica coating and 4-META/MMA-TBB resin (22.5MPa). The bond strengths of the other injection-molded thermoplastic denture base resins increased using 4-META/MMA-TBB resin. Tribochemical silica coating and 4-META/MMA-TBB resin were the most effective surface treatments among all denture base resins tested. Copyright © 2016 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

  10. Organophosphorus ester-induced chronic neurotoxicity.

    Science.gov (United States)

    Abou-Donia, Mohamed B

    2003-08-01

    Organophosphorus compounds are potent neurotoxic chemicals that are widely used in medicine, industry, and agriculture. The neurotoxicity of these chemicals has been documented in accidental human poisoning, epidemiological studies, and animal models. Organophosphorus compounds have 3 distinct neurotoxic actions. The primary action is the irreversible inhibition of acetylcholinesterase, resulting in the accumulation of acetylcholine and subsequent overstimulation of the nicotinic and muscarinic acetylcholine receptors, resulting in cholinergic effects. Another action of some of these compounds, arising from single or repeated exposure, is a delayed onset of ataxia, accompanied by a Wallerian-type degeneration of the axon and myelin in the most distal portion of the longest tracts in both the central and peripheral nervous systems, and is known as organophosphorus ester-induced delayed neurotoxicity (OPIDN). In addition, since the introduction and extensive use of synthetic organophosphorus compounds in agriculture and industry half a century ago, many studies have reported long-term, persistent, chronic neurotoxicity symptoms in individuals as a result of acute exposure to high doses that cause acute cholinergic toxicity, or from long-term, low-level, subclinical doses of these chemicals. The author attempts to define the neuronal disorder that results from organophosphorus ester-induced chronic neurotoxicity (OPICN), which leads to long-term neurological and neurobehavioral deficits. Although the mechanisms of this neurodegenerative disorder have yet to be established, the sparse available data suggest that large toxic doses of organophosphorus compounds cause acute necrotic neuronal cell death in the brain, whereas sublethal or subclinical doses produce apoptotic neuronal cell death and involve oxidative stress.

  11. Mineralogy of fossil resins in Northern Eurasia

    Science.gov (United States)

    Bogdasarov, M. A.

    2007-12-01

    The investigation is focused on identification and origin of fossil resins from the Cretaceous, Tertiary, and Quaternary sediments of Northern Eurasia on the basis of detailed study of their physical and chemical characteristics: morphology; size; mass; density; optical, mechanical, and thermal properties; chemical composition; etc. The composition of amorphous organic minerals with polymeric structure, fossil resins included, is studied with IR spectrometry, the EPR method, derivatography at low heating rates, XRD, chemical analysis, emission spectrometry, etc. The results of investigation summarized for the Baltic-Dnieper, North Siberian, and Far East amber-bearing provinces show some similarity of fossil resins in combination with specific features inherent to each province. Resins from the Baltic-Dnieper province should be termed as amber (succinite). Their variety is the most characteristic of Northern and Eastern Europe. Amber-like fossil resins from the North Siberian and Far East provinces are irrelevant to succinite. They usually occur as brittle resins, namely, retinite and gedanite, without jewelry value. Viscous fossil resin rumänite with an expected high economic value occurs in the Far East, on the shore of Sakhalin Island.

  12. Investigation of fossil resins and amber

    Directory of Open Access Journals (Sweden)

    E.Yu. Makarova

    2017-05-01

    Full Text Available Fossil resins and amber are a product of lithogenesis of resinous substances of higher plants – resinite. These components of plants, like other lipoid ingredients (suberins, coutines, sporinins, natural rubbers are resistant to microbial action, so they are well preserved in bacterial processing of organic matter in the stages of sedimento- and diagenesis, and are well diagnosed in microscopic studies. They occur in a rather wide age range of sedimentary rocks. The amber of the Baltic region of the Eocene age is most fully studied. The article presents the results of a study of the collection of fossil resins and amber from various regions of the world. Samples were studied microscopically; carbon isotope analysis, infrared spectroscopy (IR spectroscopy were performed. The most informative analysis of high-molecular polymeric compounds is IR spectroscopy. It was found that in the analyzed samples of fossil resins of different ages, aromatic compounds are not observed, most of which are first volatilized in fossilization processes. The possibility of influencing the group composition of amber and amber-like resins for sedimentation, diagenesis and catagenesis is discussed. The IR spectra of fossil and modern resin conifers are compared. Using the IR spectroscopy method, an attempt was made to identify the botanical origin of fossil resins.

  13. Melamine-modified urea formaldehyde resin for bonding particleboards

    Science.gov (United States)

    Chung-Yun Hse; Feng Fu; Hui Pan

    2008-01-01

    For the development of a cost-effective melamine-modified urea formaldehyde resin (MUF), the study evaluated the effects of reaction pH and melamine content on resin properties and bond performance of the MUF resin adhesive systems. Eight resins, each with three replicates, were prepared in a factorial experiment that included two formulation variables: two reaction...

  14. Traumatic resin ducts as indicators of bark beetle outbreaks

    Science.gov (United States)

    R. Justin DeRose; Matthew F. Bekker; James N. Long

    2017-01-01

    The formation of traumatic resin ducts (TRDs) represents an important induced defense in woody plants that enhances oleoresin production and flow in response to environmental perturbations. In some genera (Pinus), resin ducts are copious and conspicuous; however, in others (Picea), resin ducts are relatively rare. The occurrence and strength of resin ducts, in...

  15. Properties of a nanodielectric cryogenic resin

    Energy Technology Data Exchange (ETDEWEB)

    Polyzos, Georgios [ORNL; Tuncer, Enis [ORNL; Sauers, Isidor [ORNL; More, Karren Leslie [ORNL

    2010-01-01

    Physical properties of a nanodielectric composed of in situ synthesized titanium dioxide (TiO{sub 2}) nanoparticles ({le} 5 nm in diameter) and a cryogenic resin are reported. The dielectric losses were reduced by a factor of 2 in the nanocomposite, indicating that the presence of small TiO{sub 2} nanoparticles restricted the mobility of the polymer chains. Dielectric breakdown data of the nanodielectric was distributed over a narrower range than that of the unfilled resin. The nanodielectric had 1.56 times higher 1% breakdown probability than the resin, yielding 0.64 times thinner insulation thickness for the same voltage level, which is beneficial in high voltage engineering.

  16. SEM and elemental analysis of composite resins

    International Nuclear Information System (INIS)

    Hosoda, H.; Yamada, T.; Inokoshi, S.

    1990-01-01

    Twenty-four chemically cured, 21 light-cured anterior, three light-cured anterior/posterior, and 18 light-cured posterior composite resins were examined using scanning electron microscopy, and the elemental composition of their filler particles was analyzed with an energy dispersive electron probe microanalyzer. According to the results obtained, the composite resins were divided into five groups (traditional, microfilled type, submicrofilled type, hybrid type, and semihybrid), with two additional hypothetical categories (microfilled and hybrid). Characteristics of each type were described with clinical indications for selective guidance of respective composite resins for clinical use

  17. In-depth disinfection of acrylic resins.

    Science.gov (United States)

    Chau, V B; Saunders, T R; Pimsler, M; Elfring, D R

    1995-09-01

    This study demonstrated that bacteria penetrate three kinds of dental acrylic resin after a short time period. Samples of acrylic resin were contaminated with a variety of bacteria and were then placed in three different disinfecting solutions as directed by the manufacturers. After the specific dilution and immersion time, cultures were made from the resin samples. The only effective disinfectant was a 0.525% solution of sodium hypochlorite at a 10-minute immersion. It disinfected not only the surfaces but also the bacteria that penetrated the surfaces to a depth of 3 mm.

  18. Immobilisation of ion exchange resins in cement

    International Nuclear Information System (INIS)

    Howard, C.G.; Jolliffe, C.B.; Lee, D.J.

    1990-09-01

    The removal of activity from spent decontaminating solutions eg LOMI can be achieved using organic ion exchange resins. These resins can be successfully immobilised in cement based matrices. The optimum cement system contained 10% ordinary Portland cement 84% gg blast furnace slag, 6% microsilica with a water cement ratio of 0.5 and a dry resin loading of 36% with respect to total weight. This formulation was successfully scaled up to 200 litres giving a product with acceptable compressive strength, dimensional stability and elastic modulus. Storage of samples under water appears to have no detrimental effects on the product's properties. (author)

  19. Cobalt Ions Improve the Strength of Epoxy Resins

    Science.gov (United States)

    Stoakley, D. M.; St. Clair, A. K.

    1986-01-01

    Technique developed for improving mechanical strength of epoxy resins by adding cobalt ions in form of tris(acetylacetonato)cobalt (III) complex. Solid cast disks prepared from cobalt ion-containing epoxy resins tested for flexural strength and stiffness. Incorporation of cobalt ions into epoxies increased flexural strength of resins by 10 to 95 percent. Suitable resins for this technique include any liquid or solid TGMDA resins. Improved epoxy formulation proves useful as composite matrix resin, adhesive, or casting resin for applications on commercial and advanced aircraft.

  20. Thermal and mechanical properties of fatty acid starch esters.

    Science.gov (United States)

    Winkler, H; Vorwerg, W; Rihm, R

    2014-02-15

    The current study examined thermal and mechanical properties of fatty acid starch esters (FASEs). All highly soluble esters were obtained by the sustainable, homogeneous transesterification of fatty acid vinyl esters in dimethylsulfoxide (DMSO). Casted films of products with a degree of substitution (DS) of 1.40-1.73 were compared with highly substituted ones (DS 2.20-2.63). All films were free of any plasticizer additives. Hydrophobic surfaces were characterized by contact angle measurements. Dynamic scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) revealed thermal transitions (T(g), T(m)) which were influenced by the internal plasticizing effect of the ester groups. Thermal gravimetric analysis (TGA) measurements showed the increased thermal stability toward native starch. Tensile tests revealed the decreasing strength and stiffness of the products with increasing ester-group chain length while the elongation increased up to the ester group laurate and after that decreased. Esters of the longest fatty acids, palmitate and stearate turned out to be brittle materials due to super molecular structures of the ester chains such as confirmed by X-ray. Summarized products with a DS 1.40-1.73 featured more "starch-like" properties with tensile strength up to outstanding 43 MPa, while products with a DS >2 behaved more "oil-like". Both classes of esters should be tested as a serious alternative to commercial starch blends and petrol-based plastics. The term Cnumber is attributed to the number of total C-Atoms of the fatty acid (e.g. C6=Hexanoate). Copyright © 2013 Elsevier Ltd. All rights reserved.

  1. Shear bond strength of an autopolymerizing repair resin to injection-molded thermoplastic denture base resins.

    Science.gov (United States)

    Hamanaka, Ippei; Shimizu, Hiroshi; Takahashi, Yutaka

    2013-09-01

    This study investigated the shear bond strength of an autopolymerizing repair resin to injection-molded thermoplastic denture base resins. Four injection-molded thermoplastic resins (two polyamides, a polyethylene terephthalate copolymer and a polycarbonate) were used in this study. The specimens were divided into eight groups according to the type of surface treatment given: (1) no treatment, (2) air abrasion with alumina, (3) dichloromethane, (4) ethyl acetate, (5) 4-META/MMA-TBB resin, (6) alumina and 4-META/MMA-TBB resin, (7) tribochemical silica coating or (8) tribochemical silica coating and 4-META/MMA-TBB resin. Half of the specimens in groups 1, 5, 6 and 8 were thermocycled for 10,000 cycles in water between 5-55°C with a dwell time of 1 min at each temperature. The shear bond strengths were determined. The shear bond strengths to the two polyamides treated with alumina, dichloromethane and ethyl acetate and no treatment were very low. The greatest post-thermocycling bond strengths to polyamides were recorded for the specimens treated with tribochemical silica coating and 4-META/MMA-TBB resin (PA12: 16.4 MPa, PACM12: 17.5 MPa). The greatest post-thermocycling bond strengths to polyethylene terephthalate copolymer and polycarbonate were recorded for the treatment with alumina and 4-META/MMA-TBB resin (22.7 MPa, 20.8 MPa). Polyamide was exceedingly difficult to bond to an autopolymerizing repair resin; the shear bond strength improved using tribochemical silica coating followed by the application of 4-META/MMA-TBB resin. Both polyethylene terephthalate copolymer and polycarbonate were originally easy to bond to an autopolymerizing repair resin. However, with 4-META/MMA-TBB resin, the bond was more secure.

  2. Magnetic ion-exchange resin treatment: Impact of water type and resin use

    OpenAIRE

    Mergen, Maxime Rodolphe Denis; Jefferson, Bruce; Parsons, Simon A.; Jarvis, Peter

    2008-01-01

    Three raw waters of fundamentally different natural organic matter (NOM) character were treated by magnetic resin using a bench-scale method designed to mimic how the resin is used in continuous operation. Increasing water hydrophobicity resulted in reduced dissolved organic carbon (DOC) removal with removal of 56%, 33% and 25% for waters containing 21%, 50% and 75% hydrophobic NOM, respectively. Study of consecutive resin uses showed that the NOM in the hydrophobic water ha...

  3. 5-year clinical performance of resin composite versus resin modified glass ionomer restorative system in non-carious cervical lesions

    DEFF Research Database (Denmark)

    Franco, Eduardo Batista; Benetti, Ana Raquel; Ishikiriama, Sérgio Kiyoshi

    2006-01-01

    To comparatively assess the 5-year clinical performance of a 1-bottle adhesive and resin composite system with a resin-modified glass ionomer restorative in non-carious cervical lesions.......To comparatively assess the 5-year clinical performance of a 1-bottle adhesive and resin composite system with a resin-modified glass ionomer restorative in non-carious cervical lesions....

  4. 21 CFR 175.380 - Xylene-formaldehyde resins condensed with 4,4′-isopropylidenediphenol-epichlorohydrin epoxy resins.

    Science.gov (United States)

    2010-04-01

    ...-isopropylidenediphenol-epichlorohydrin epoxy resins. 175.380 Section 175.380 Food and Drugs FOOD AND DRUG ADMINISTRATION... Xylene-formaldehyde resins condensed with 4,4′-isopropylidenediphenol-epichlorohydrin epoxy resins. The...′-isopropylidenediphenol-epichlorohydrin epoxy resins, to which may have been added certain optional adjuvant substances...

  5. Boric Ester-Type Molten Salt via Dehydrocoupling Reaction

    OpenAIRE

    Noriyoshi Matsumi; Yoshiyuki Toyota; Prerna Joshi; Puhup Puneet; Raman Vedarajan; Toshihiro Takekawa

    2014-01-01

    Novel boric ester-type molten salt was prepared using 1-(2-hydroxyethyl)-3-methylimidazolium chloride as a key starting material. After an ion exchange reaction of 1-(2-hydroxyethyl)-3-methylimidazolium chloride with lithium (bis-(trifluoromethanesulfonyl) imide) (LiNTf2), the resulting 1-(2-hydroxyethyl)-3-methylimidazolium NTf2 was reacted with 9-borabicyclo[3.3.1]nonane (9-BBN) to give the desired boric ester-type molten salt in a moderate yield. The structure of the boric ester-type molt...

  6. Catalytic Oxidation of Allylic Alcohols to Methyl Esters

    DEFF Research Database (Denmark)

    Gallas-Hulin, Agata; Kotni, Rama Krishna; Nielsen, Martin

    2017-01-01

    Aerobic oxidation of allylic alcohols to methyl esters using gold nanoparticles supported on different metal oxide carriers has been performed successfully under mild conditions (room temperature, 0.1 MPa O2) without significant loss of catalytic activity. The effects of different reaction...... parameters are studied to find the suitable reaction conditions. All catalysts are characterised by XRD, XRF and TEM. Among these catalysts, Au/TiO2 showed the most efficient catalytic activity towards the selective oxidation of allylic alcohols to the corresponding esters. Moreover, the same Au/TiO2...... to synthesize methyl esters from allylic alcohols....

  7. Sugar ester surfactants: enzymatic synthesis and applications in food industry.

    Science.gov (United States)

    Neta, Nair S; Teixeira, José A; Rodrigues, Lígia R

    2015-01-01

    Sugar esters are non-ionic surfactants that can be synthesized in a single enzymatic reaction step using lipases. The stability and efficiency of lipases under unusual conditions and using non-conventional media can be significantly improved through immobilization and protein engineering. Also, the development of de novo enzymes has seen a significant increase lately under the scope of the new field of synthetic biology. Depending on the esterification degree and the nature of fatty acid and/or sugar, a range of sugar esters can be synthesized. Due to their surface activity and emulsifying capacity, sugar esters are promising for applications in food industry.

  8. Acyl-lupeol esters from Parahancornia amapa (Apocynaceae

    Directory of Open Access Journals (Sweden)

    Carvalho Mário G. de

    2001-01-01

    Full Text Available From the roots of Parahancornia amapa, family Apocynaceae, the following compounds were isolated and identified nine new and ten known 3beta-O-acyl lupeol esters, beta-sitosterol, stigmasterol, beta-sitosterone, the triterpenoids beta-amyrin, alpha-amyrin, lupeol and their acetyl derivatives. The structures of these compounds were established by spectroscopic data, mainly ¹H and 13C (HBBD and DEPT NMR spectra. The methyl esters obtained by hydrolysis of acyl lupeol esters and methylation of the corresponding acids were characterized by MS-GC analysis.

  9. The strengthening of resin cemented dental ceramic materials

    OpenAIRE

    Hooi, Paul

    2013-01-01

    The aim of the current investigation was to advance the understanding of the mechanism of resin-strengthening conferred to dental ceramic materials by resin-based composite materials. The investigation is presented as a series of manuscripts. In the first study (Manuscript 3.1), dental porcelain disc-shaped specimens were resin-coated with three resin-based composite materials with different flexural moduli at discrete resin thicknesses. The discs were loaded to failure in a biaxial flexure t...

  10. Pengaruh Sifat-Sifat Fisik Resin Akrilik Terhadap Basis Protesa

    OpenAIRE

    Amriani Syahfitri

    2008-01-01

    Saat ini resin akrilik banyak digunakan secara umum untuk konstruksi gigi tiruan. Sebagai bahan basis prothesa, penggunaan resin akrilik terutama resin heat cured adalah yang paling sering digunakan selain bernilai estetis, juga lebih ekonomis. Pada prothesa yang ideal memerlukan suatu basis yang kuat, Syarat- syarat basis protesa tidak semuanya dapat dipenuhi oleh basis resin akrilik. Sifat-sifat fisik resin akrilik mempunyai pengaruh terhadap basis protesa. Untuk menghindari k...

  11. Resin Flow Analysis in the Injection Cycle of a Resin Transfer Molded Radome

    Science.gov (United States)

    Golestanian, Hossein; Poursina, Mehrdad

    2007-04-01

    Resin flow analysis in the injection cycle of an RTM process was investigated. Fiberglass and carbon fiber mats were used as reinforcements with EPON 826 epoxy resin. Numerical models were developed in ANSYS finite element software to simulate resin flow behavior into a mold of conical shape. Resin flow into the woven fiber mats is modeled as flow through porous media. The injection time for fiberglass/epoxy composite is found to be 4407 seconds. Required injection time for the carbon/epoxy composite is 27022 seconds. Higher injection time for carbon/epoxy part is due to lower permeability value of the carbon fibers compared to glass fiber mat.

  12. Dental repair material: a resin-modified glass-ionomer bioactive ionic resin-based composite.

    Science.gov (United States)

    Croll, Theodore P; Berg, Joel H; Donly, Kevin J

    2015-01-01

    This report documents treatment and repair of three carious teeth that were restored with a new dental repair material that features the characteristics of both resin-modified glass-ionomer restorative cement (RMGI) and resin-based composite (RBC). The restorative products presented are reported by the manufacturer to be the first bioactive dental materials with an ionic resin matrix, a shock-absorbing resin component, and bioactive fillers that mimic the physical and chemical properties of natural teeth. The restorative material and base/liner, which feature three hardening mechanisms, could prove to be a notable advancement in the adhesive dentistry restorative materials continuum.

  13. Nanosilica Modification of Elastomer-Modified VARTM Epoxy Resins for Improved Resin and Composite Toughness

    National Research Council Canada - National Science Library

    Robinette, Jason; Bujanda, Andres; DeSchepper, Daniel; Dibelka, Jessica; Costanzo, Philip; Jensen, Robert; McKnight, Steven

    2007-01-01

    Recent publications have reported a synergy between rubber and silica in modified epoxy resins that results in significantly improved fracture toughness without reductions in other material properties...

  14. Posterior bulk-filled resin composite restorations.

    DEFF Research Database (Denmark)

    van Dijken, Jan WV; Pallesen, Ulla

    2016-01-01

    Purpose/aim: To evaluate in a randomized controlled study the 5-year clinical durability of a flowable resin composite bulk-fill technique in Class I and Class II restorations. Materials and methods: 38 pairs Class I and 62 pairs Class II restorations were placed in 44 male and 42 female (mean age...... 52.4 years). Each patient received at least two, as similar as possible, extended Class I or Class II restorations. In all cavities, a 1-step self-etch adhesive (Xeno V+) was applied. Randomized, one of the cavities of each pair received the flowable bulk-filled resin composite (SDR), in increments...... up to 4mm as needed to fill the cavity 2mm short of the occlusal cavosurface. The occlusal part was completed with the nano-hybrid resin composite (Ceram X mono+). In the other cavity, the resin composite-only (Ceram X mono+) was placed in 2mm increments. The restorations were evaluated using...

  15. 21 CFR 177.1380 - Fluorocarbon resins.

    Science.gov (United States)

    2010-04-01

    ...) Chlorotrifluoroethylene-1,1-difluoroethylene-tetrafluoroethylene co-polymer resins produced by copolymerization of..., Extrusion, and Coating Materials,” which is incorporated by reference in accordance with 5 U.S.C. 552(a) and...

  16. Liquid Resins With Low VOC Emissions

    National Research Council Canada - National Science Library

    LaScala, John J; Sands, James M; Palmese, Guiseppe R

    2004-01-01

    .... The polymer properties were similar to that of commercial resins, including Tg greater than 120 C, flex strength greater than 100 MPa, modulus of approximately 3 GPa, and fracture toughness greater than 200 J/m2...

  17. 21 CFR 177.1655 - Polysulfone resins.

    Science.gov (United States)

    2010-04-01

    ... by osmotic pressure in monochlorobenzene; or (2) 1,1′-Sulfonylbis[4-chlorobenzene] polymer with 4,4... determined by osmotic pressure in dimethylformamide. (b) The basic polysulfone resins identified in paragraph...

  18. Volumetric polymerization shrinkage of contemporary composite resins

    Directory of Open Access Journals (Sweden)

    Halim Nagem Filho

    2007-10-01

    Full Text Available The polymerization shrinkage of composite resins may affect negatively the clinical outcome of the restoration. Extensive research has been carried out to develop new formulations of composite resins in order to provide good handling characteristics and some dimensional stability during polymerization. The purpose of this study was to analyze, in vitro, the magnitude of the volumetric polymerization shrinkage of 7 contemporary composite resins (Definite, Suprafill, SureFil, Filtek Z250, Fill Magic, Alert, and Solitaire to determine whether there are differences among these materials. The tests were conducted with precision of 0.1 mg. The volumetric shrinkage was measured by hydrostatic weighing before and after polymerization and calculated by known mathematical equations. One-way ANOVA (a or = 0.05 was used to determine statistically significant differences in volumetric shrinkage among the tested composite resins. Suprafill (1.87±0.01 and Definite (1.89±0.01 shrank significantly less than the other composite resins. SureFil (2.01±0.06, Filtek Z250 (1.99±0.03, and Fill Magic (2.02±0.02 presented intermediate levels of polymerization shrinkage. Alert and Solitaire presented the highest degree of polymerization shrinkage. Knowing the polymerization shrinkage rates of the commercially available composite resins, the dentist would be able to choose between using composite resins with lower polymerization shrinkage rates or adopting technical or operational procedures to minimize the adverse effects deriving from resin contraction during light-activation.

  19. Cycloaliphatic epoxide resins for cationic UV - cure

    International Nuclear Information System (INIS)

    Verschueren, K.; Balwant Kaur

    1999-01-01

    This paper introduces the cyclo - aliphatic epoxide resins used for the various applications of radiation curing and their comparison with acrylate chemistry. Radiation curable coatings and inks are pre - dominantly based on acrylate chemistry but over the last few years, cationic chemistry has emerged successfully with the unique properties inherent with cyclo - aliphatic epoxide ring structures. Wide variety of cationic resins and diluents, the formulation techniques to achieve the desired properties greatly contributes to the advancement of UV - curing technology

  20. Damage evolution in a filled epoxy resin

    International Nuclear Information System (INIS)

    Depoorter, Nicolas; Coutellier, Daniel; Muzic, Markus; Berg-Pollack, Antje; Cai Ye; Zimmermann, Andre

    2006-01-01

    A method is proposed for studying damage evolution in a filled epoxy resin submitted to low-cycle fatigue loading. Transmission electron microscopy analysis was performed, which indicates a damage mechanism that corresponds well to the decreasing slope of the stress-strain hysteresis observed in strain-controlled fatigue experiments. Also, the suggested damage model appears to be suitable for the simulation of strain-controlled cyclic tests and fits the damage evolution of the filled epoxy resin fairly well [de

  1. PROCESS FOR HYDROGENOLYSIS OF ALPHA-HYDROXY ESTERS OR ACIDS USING A HETEROGENEOUS CATALYST

    DEFF Research Database (Denmark)

    2017-01-01

    The present invention relates to a method for hydrogenolysis of alpha-hydroxy esters or acids, comprising reacting the alpha-hydroxy ester or acid in the presence of a heterogeneous catalyst. The present invention also relates to a method for producing propionic acid ester, and the use of any...... of the methods for the production of propionic acid esters, such as alkyl propionate....

  2. Complex formation of technetium with the methyl esters of MAG2 and MAG1

    International Nuclear Information System (INIS)

    Noll, B.; Noll, S.; Grosse, B.; Johannsen, B.; Spies, H.

    1993-01-01

    Mercaptoacetylglycine methyl ester (MAG 2 ester) and mercaptoacetyldiglycine methyl ester (MAG 1 ester) were included to investigate complex formation of SH/amide ligands with technetium. The studies are aimed at finding out how blocking the carboxylic groups influences the complexation reaction, with a view to finding an approach to new lipophilic species. (orig./BBR)

  3. 21 CFR 172.852 - Glyceryl-lacto esters of fatty acids.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Glyceryl-lacto esters of fatty acids. 172.852... HUMAN CONSUMPTION Multipurpose Additives § 172.852 Glyceryl-lacto esters of fatty acids. Glyceryl-lacto esters of fatty acids (the lactic acid esters of mono- and diglycerides) may be safely used in food in...

  4. Chemoenzymatic Synthesis and Chemical Recycling of Poly(ester-urethanes

    Directory of Open Access Journals (Sweden)

    Hiroto Hayashi

    2011-08-01

    Full Text Available Novel poly(ester-urethanes were prepared by a synthetic route using a lipase that avoids the use of hazardous diisocyanate. The urethane linkage was formed by the reaction of phenyl carbonate with amino acids and amino alcohols that produced urethane-containing diacids and hydroxy acids, respectively. The urethane diacid underwent polymerization with polyethylene glycol and a,w-alkanediols and also the urethane-containing hydroxy acid monomer was polymerized by the lipase to produce high-molecular-weight poly(ester-urethanes. The periodic introduction of ester linkages into the polyurethane chain by the lipase-catalyzed polymerization afforded chemically recyclable points. They were readily depolymerized in the presence of lipase into cyclic oligomers, which were readily repolymerized in the presence of the same enzyme. Due to the symmetrical structure of the polymers, poly(ester-urethanes synthesized in this study showed higher Tm, Young’s modulus and tensile strength values.

  5. Space-Qualifiable Cyanate Ester Elastomer, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Cornerstone Research Group, Inc. (CRG) proposes to design and develop a space-qualifiable cyanate ester elastomer for application in self-deployable space structures...

  6. Biocatalytic synthesis and antioxidant capacities of ascorbyl esters ...

    African Journals Online (AJOL)

    ajl yemi

    2011-11-28

    , 2009). Lipases, especially that from Candida antarctica, have been successfully used to catalyze the synthesis of ascorbyl esters in tertiary alcohols, acetone and even in ionic liquids, employing saturated and unsaturated ...

  7. [Exposure to vegetal esters based metal cutting fluids: health effects].

    Science.gov (United States)

    Riva, M M; Bellini, M; Leghissa, P; Gambini, D; Mosconi, G

    2012-01-01

    The aim of our research is to study respiratory and dermatologic diseases (irritative and allergic) in a cohort of workers exposed to vegetal esters based metal cutting fluids of the latest generation. A cohort of 81 workers (mean age 34.5 years, seniority 17.4 years), with mean exposure to vegetal esters based metal cutting fluids of 2.8 years, has been subjected to clinical evaluations. The investigation did not reveal any disease or disorder of the respiratory system, any folluculitis or any allergic contact dermatitis caused by sensitization to vegetal esters based metal cutting fluids. On the contrary we documented 5 cases of irritant contact dermatitis, even if favored by an improper use of protection devices. According to early results, the introduction of vegetal esters based metal cutting fluids seems to reduce the risk to the worker's health. A longitudinal surveillance is still needed to confirm that even in the medium and long-term sensitizations will not occur.

  8. Diterpene esters of aristolochic acids from Aristolochia pubescens.

    Science.gov (United States)

    Nascimento, Isabele R; Lopes, Lucia M X

    2003-08-01

    From the acetone and ethanol extracts of the tubercula of Aristolochia pubescens, two diterpene esters of aristolochic acids were isolated, together with 23 known compounds. The structures of the compounds were determined on the basis of spectroscopic analysis.

  9. Space-Qualifiable Cyanate Ester Elastomer, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — In Phase 1, CRG demonstrated the feasibility of a novel approach to prepare cyanate ester based elastomers. This approach polymerizes in-situ siloxane within a...

  10. Incorporation of Epicatechin Esters into Lignin Enhances Cell Wall Fermentability

    Science.gov (United States)

    Polyphenolic catechin esters are potentially attractive targets for lignin bioengineering because their copolymerization with monolignols could reduce lignin hydrophobicity and cross-linking to polysaccharides, or facilitate delignification by biomass pretreatments. To test this hypothesis, we biomi...

  11. Baker's yeast: production of D- and L-3-hydroxy esters

    DEFF Research Database (Denmark)

    Dahl, Allan Carsten; Madsen, Jørgen Øgaard

    1998-01-01

    Baker's yeast grown under oxygen limited conditions and used in the reduction of 3-oxo esters results in a shift of the stereoselectivity of the yeast towards D-hydroxy esters as compared with ordinary baker's yeast. The highest degree of stereoselectivity was obtained with growing yeast or yeast...... harvested while growing. In contrast, the stereoselectivity was shifted towards L-hydroxy esters when the oxo esters were added slowly to ordinary baker's yeast supplied with gluconolactone as co-substrate. The reduction rate with gluconolactone was increased by active aeration. Ethyl L-(S)-3......-hydroxybutanoate was afforded in >99% ee. Both enantiomers of ethyl 3-hydroxypentanoate, D-(R) in 96% ee and L-(S) in 93% ee, and of ethyl 4-chloro-3-hydroxybutanoate, D-(S) in 98% ee and L-(R) in 94% ee, were obtained. The results demonstrate that the stereoselectivity of baker's yeast can be controlled...

  12. Thiolsulfonate functionalized polystyrene resin: preparation and application in the isolation and identification of electrophilic mutagens.

    Science.gov (United States)

    Wu, E; Carlson, Robert M

    2007-01-01

    A new approach for isolation and identification of elecrtophilic mutagens from complex matrix was developed. Thiosulfonic anion was immobilized onto polystyrene beads and used as separation media. Potassium polystyryl-thiosulfonate, prepared from polystyrylsulfonyl chloride and KHS, was observed to selectively react with model electrophilic mutagens such as alkyl halides, a-chloroketones and alpha-chloroesters to produce polystyryl-thiosulfonic esters. After separation from other nonreactive organic compounds, the beads then reacted with ethanethiol to produce unsymmetrical ethyl disulfides which are easily detected by GC/MS. For one mutagenic compound, only one unsymmetrical disulfide was found to contain its structure part. Thus, the structure of the parent mutagens could be deduced from that of the unsymmetrical disulfides. The degree of functionalization of the potassium polystyryl-thiosulfonate resin was 1.11 mmol/g. Its reactivity was discussed and its recycling method was reported here.

  13. Combustion characteristics of the mustard methyl esters

    International Nuclear Information System (INIS)

    Bannikov, M.G.; Vasilev, I.P.

    2011-01-01

    Mustard Methyl Esters (further bio diesel) and regular diesel fuel were tested in direct injection diesel engine. Analysis of experimental data was supported by an analysis of fuel injection and combustion characteristics. Engine fuelled with bio diesel had increased brake specific fuel consumption, reduced nitrogen oxides emission and smoke opacity, moderate increase in carbon monoxide emission with essentially unchanged unburned hydrocarbons emission. Increase in fuel consumption was attributed to lesser heating value of bio diesel and partially to decreased fuel conversion efficiency. Analysis of combustion characteristics revealed earlier start of injection and shorter ignition delay period of bio diesel. Resulting decrease in maximum rate of heat release and cylinder pressure was the most probable reason for reduced emission of nitrogen oxides. Analysis of combustion characteristics also showed that cetane index determined by ASTM Method D976 is not a proper measure of ignition quality of bio diesel. Conclusion was made on applicability of mustard oil as a source for commercial production of bio diesel in Pakistan. Potentialities of on improving combustion and emissions characteristics of diesel engine by reformulating bio diesel were discussed. (author)

  14. Sulfur deactivation of fatty ester hydrogenolysis catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Brands, D.S.; U-A-Sai, G.; Poels, E.K.; Bliek, A. [Univ. of Amsterdam (Netherlands). Dept. of Chemical Engineering

    1999-08-15

    Trace organosulfur compounds present as natural impurities in oleochemical feedstocks may lead to activation of copper-containing catalysts applied for hydrogenolysis of esters toward fatty alcohols. In this paper, the sulfur deactivation of Cu/SiO{sub 2} and Cu/ZnO/SiO{sub 2} catalysts was studied in the liquid-phase hydrogenolysis of methyl palmitate. The rate of deactivation is fast and increases as a function of the sulfur-containing compound present: octadecanethiol {approx} dihexadecyl disulfide < benzyl isothiocyanate < methyl p-toluene sulfonate < dihexadecyl sulfide < dibenzothiophene. The rapid deactivation is caused by the fact that sulfur is quantitatively removed from the reaction mixture and because mainly surface sulfides are formed under hydrogenolysis conditions. The life time of a zinc-promoted catalyst is up to two times higher than that of the Cu/SiO{sub 2} catalyst, most likely due to zinc surface sulfide formation. The maximum sulfur coverage obtained after full catalyst deactivation with dibenzothiophene and dihexadecyl sulfide--the sulfur compounds that cause the fastest deactivation--may be as low as 0.07. This is due to the fact that decomposition of these compounds as well as the hydrogenolysis reaction itself proceeds on ensembles of copper atoms. Catalyst regeneration studies reveal that activity cannot be regained by reduction or combined oxidation/reduction treatments. XRD, TPR, and TPO results confirm that no distinct bulk copper or zinc sulfide or sulfate phases are present.

  15. Solid state crystallisation of oligosaccharide ester derivatives

    CERN Document Server

    Wright, E A

    2002-01-01

    An investigation of the solid state properties of oligosaccharide ester derivatives (OEDs) with potential applications in drug delivery has been carried out. The amorphous form of two OEDs, trehalose octa-acetate (TOAC) and 6:6'-di-(beta-tetraacetyl glucuronyl)-hexaacetyl trehalose (TR153), was investigated as a matrix for the sustained release of active ingredients. The matrices showed a tendency to crystallise and so polymorph screens were performed to provide crystalline samples for structural analysis. The crystal structures of TOAC methanolate and TR153 acetonitrile solvate have been determined by single-crystal laboratory X-ray diffraction. TOAC methanolate crystallises in the orthorhombic space group P2 sub 1 2 sub 1 2 sub 1 with a = 15.429(18) A, b = 17.934(19) A and c = 13.518(4) A at 123 K. The structure is isomorphous with the previously reported structure of TOAC monohydrate form II. TR153 acetonitrile solvate crystallises in the monoclinic spacegroup C2 with a = 30:160(6) A, b = 11.878(3) A, c 20...

  16. How Well Does BODIPY-Cholesteryl Ester Mimic Unlabeled Cholesteryl Esters in High Density Lipoprotein Particles?

    DEFF Research Database (Denmark)

    Karilainen, Topi; Vuorela, Timo; Vattulainen, Ilpo

    2015-01-01

    We compare the behavior of unlabeled and BODIPY-labeled cholesteryl ester (CE) in high density lipoprotein by atomistic molecular dynamics simulations. We find through replica exchange umbrella sampling and unbiased molecular dynamics simulations that BODIPY labeling has no significant effect...... on the partitioning of CE between HDL and the water phase. However, BODIPY-CE was observed to diffuse more slowly and locate itself closer to the HDL-water interface than CE due to the BODIPY probe that is constrained to the surface region, and because the CE body in BODIPY-CE prefers to align itself away from...

  17. Methods of refining and producing dibasic esters and acids from natural oil feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Snead, Thomas E.; Cohen, Steven A.; Gildon, Demond L.

    2016-03-15

    Methods are provided for refining natural oil feedstocks and producing dibasic esters and/or dibasic acids. The methods comprise reacting a terminal olefin with an internal olefin in the presence of a metathesis catalyst to form a dibasic ester and/or dibasic acid. In certain embodiments, the olefin esters are formed by reacting the feedstock in the presence of a metathesis catalyst under conditions sufficient to form a metathesized product comprising olefins and esters, separating the olefins from the esters in the metathesized product, and transesterifying the esters in the presence of an alcohol to form a transesterified product having olefin esters.

  18. Methods of refining and producing dibasic esters and acids from natural oil feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Snead, Thomas E; Cohen, Steven A; Gildon, Demond L

    2015-04-07

    Methods are provided for refining natural oil feedstocks and producing dibasic esters and/or dibasic acids. The methods comprise reacting a terminal olefin with an internal olefin in the presence of a metathesis catalyst to form a dibasic ester and/or dibasic acid. In certain embodiments, the olefin esters are formed by reacting the feedstock in the presence of a metathesis catalyst under conditions sufficient to form a metathesized product comprising olefins and esters, separating the olefins from the esters in the metathesized product, and transesterifying the esters in the presence of an alcohol to form a transesterified product having olefin esters.

  19. RAFT Polymerization of Vinyl Esters: Synthesis and Applications

    OpenAIRE

    Simon Harrisson; Xuan Liu; Jean-Noël Ollagnier; Olivier Coutelier; Jean-Daniel Marty; Mathias Destarac

    2014-01-01

    This article is the first comprehensive review on the study and use of vinyl ester monomers in reversible addition fragmentation chain transfer (RAFT) polymerization. It covers all the synthetic aspects associated with the definition of precision polymers comprising poly(vinyl ester) building blocks, such as the choice of RAFT agent and reaction conditions in order to progress from simple to complex macromolecular architectures. Although vinyl acetate was by far the most studied monomer of th...

  20. The enantioselective b-keto ester reductions by Saccharomyces cerevisiae

    Directory of Open Access Journals (Sweden)

    HASSAN TAJIK

    2006-09-01

    Full Text Available The enantioselective yeast reduction of aromatic b-keto esters, by use of potassium dihydrogen phosphate, calcium phosphate (monobasic, magnesium sulfate and ammonium tartrate (diammonium salt (10:1:1:50 in water at pH 7 as a buffer for 72–120 h with 45–90 % conversion to the corresponding aromatic -hydroxy esters was achieved by means of Saccharomyces cerevisiae.

  1. Methods of refining and producing isomerized fatty acid esters and fatty acids from natural oil feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Snead, Thomas E.; Cohen, Steven A.; Gildon, Demond L.; Beltran, Leslie V.; Kunz, Linda A.; Pals, Tessa M.; Quinn, Jordan R; Behrends, Jr., Raymond T.; Bernhardt, Randal J.

    2016-07-05

    Methods are provided for refining natural oil feedstocks and producing isomerized esters and acids. The methods comprise providing a C4-C18 unsaturated fatty ester or acid, and isomerizing the fatty acid ester or acid in the presence of heat or an isomerization catalyst to form an isomerized fatty ester or acid. In some embodiments, the methods comprise forming a dibasic ester or dibasic acid prior to the isomerizing step. In certain embodiments, the methods further comprise hydrolyzing the dibasic ester to form a dibasic acid. In certain embodiments, the olefin is formed by reacting the feedstock in the presence of a metathesis catalyst under conditions sufficient to form a metathesized product comprising olefins and esters, separating the olefins from the esters in the metathesized product, and transesterifying the esters in the presence of an alcohol to form a transesterified product having unsaturated esters.

  2. A study of the autoxidation of some unsaturated fatty acid methyl esters using Fourier transform Raman spectroscopy

    Science.gov (United States)

    Agbenyega, J. K.; Claybourn, M.; Ellis, G.

    Near-infrared Fourier transform Raman and Fourier transform infrared spectroscopy have been used to investigate the chemical changes taking place during the curing reaction of several fatty acid methyl esters, which are used for modelling processes in the autoxidation of alkyd resin coatings. We have studied methyl oleate, methyl linoleate, and methyl linolenate in an attempt to monitor the degree of unsaturation within the fatty acid methyl esters (FAMES) during the complex autoxidation/polymerisation reaction that takes place once the paint system is coated onto a substrate and exposed to the atmosphere. The peaks around 1655 cm -1 have been assigned as follows: to the trans isomer at 1670 cm -1, the cis isomer at 1655 cm -1 and the conjugated structure at 1640 cm -1 [B. Schrader, Raman/Infrared Atlas of Organic Compounds (2nd Edn), VCH, Weinheim (1989); J. K. Abenyega, M. Claybourn and G. Ellis, in preparations]. Raman spectra for the cure of methyl linoleate after 24 h show several interesting features, suggesting the formation of a highly conjugated cyclic structure. Current theories about the mechanism for the autoxidation of methyl linoleate make no mention of this aromatic product.

  3. The mystery of the 'resin-of-canuaru': a medicine used by caboclos river-dwellers of the Amazon, Amazonas, Brazil.

    Science.gov (United States)

    Rodrigues, E; Santos, J de F L; Souza, S M; Lago, J H G

    2012-12-18

    'Resin-of-canuaru' is a medicine utilized by caboclos living in the Amazon Region, Brazil. There is a mystery regarding its origin because the caboclos maintain that this substance is derived only from animal secretions (from a frog called canuaru), whereas the historic literature claims that 'resin-of-canuaru' is derived solely from a plant exudate (resin). Based on our ethnographic studies, we hypothesized that this substance is a combination of both. Because the past reports on this resiniferous material in the literature are based solely on observations, we aimed to present ethnographic, zoological and chemical data to try to elucidate the origin of the 'resin-of-canuaru'. Ethnographic techniques and methods were applied, including participant observation, the use of field diaries and informal and unstructured interviews. The canuaru frog (Trachycephalus resinifictrix Goeldi, 1907) and 'resin-of-canuaru' were collected for taxonomic identification and chemical analysis, respectively. The resiniferous 'resin-of-canuaru' was extracted using MeOH and then analyzed by silica gel TLC and NMR. Canuaru frogs live in tree cavities and secrete a large amount of substances during spawning, resulting in a resiniferous material. NMR analysis of the MeOH extract of this crude material showed peaks assigned to 3,4-secofriedel-4(23)-en-3-oic acid (putranjuvic acid) and its methyl ester derivative (methyl putranjivate) and to biogenetic precursor of these two compounds (a lactone derivative), which is formed by the oxidation of friedelin. Based on evidence that Protium species accumulate primarily tetracyclic/pentacyclic triterpenoids and that the co-occurrence of the compounds listed above is rarely described in plant species, we suggest that these compounds could be products of the biotransformation of friedelin by the frog. According to our data, the 'resin-of-canuaru' seems to have both animal and vegetal origins. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

  4. Imide modified epoxy matrix resins

    Science.gov (United States)

    Scola, D. A.

    1984-01-01

    The results of a program designed to develop tough imide modified epoxy resins cured by bisimide amine (BIA) hardeners are described. State-of-the-art epoxides MY720 and DER383 were used, and four bismide amines were evaluated. These were the BIA's derived from the 6F anhydride (4,4'-(hexafluoroisopropylidene) bis(phthalic anhydride) and the diamines 3,3'-diaminodiphynyl sulfone, 4,4'-oxygianiline, 4,4'-methylene dianiline, and 1,12-dodecane diamine. A key intermediate, designated 6F anhydride, is required for the synthesis of the bisimide amines. Reaction parameters to synthesize a precursor to the 6F anhydride (6FHC) in high yields were investigated. The catalyst trifluoromethane sulfonic acid was studied. Although small scale runs yielded the 6FHC in 50 percent yield, efforts to ranslate these results to a larger scale synthesis gave the 6FHC in only 9 percent yield. Results show that the concept of using bisimide amine as curing agents to improve the toughness properties of epoxies is valid.

  5. Resin elasticity and the strengthening of all-ceramic restorations.

    Science.gov (United States)

    Addison, O; Marquis, P M; Fleming, G J P

    2007-06-01

    Resin luting of all-ceramic restorations results in increased performance; however, the strengthening mechanism and the role of the mechanical properties of the resin are not fully understood. The hypothesis tested is that ceramic strength enhancement is dependent on the elastic modulus of the resin. Three-point flexural moduli of a flowable, luting, and hybrid composite resin were characterized. Two hundred forty porcelain discs were air-abraded. One group acted as a control, and 3 additional groups were coated with 120 +/- 20 microm of each resin prior to bi-axial flexure testing. All resins significantly increased in mean strength, and the associated strength increase was related to the elastic modulus of the resin (R(2) = 0.9885), so the hypothesis was accepted. The combination of Poisson constraint and the creation of a resin-inter-penetrating layer sensitive to the elastic modulus of the resin may provide an explanation of the strengthening mechanism.

  6. Effect of resin coating on dentin bonding of resin cement in Class II cavities.

    Science.gov (United States)

    Sultana, Shamim; Nikaido, Toru; Matin, Khairul; Ogata, Miwako; Foxton, Richard M; Tagami, Junji

    2007-07-01

    This study was designed to evaluate the efficacy of resin coating on the regional microtensile bond strength (MTBS) of a resin cement to the dentin walls of Class II cavities. Twenty mesio-occlusal cavities were prepared in human molars. In 10 cavities, a resin coating consisting of a self-etching primer bonding system, Clearfil SE Bond, and a low-viscosity microfilled resin, Protect Liner F, was applied. The other 10 teeth served as a non-coating group. After impression taking and temporization, they were kept in water for one day. Composite inlays were then cemented with a dual-cure resin cement, Panavia F 2.0, and stored in water for one day. Thereafter, MTBSs were measured. Two-way ANOVA (p=0.05) revealed that the MTBS of resin cement to dentin was influenced by resin coating, but not by regional difference. In conclusion, application of a resin coating to the dentin surface significantly improved the MTBS in indirect restorations.

  7. Bond strength of resin-resin interfaces contaminated with saliva and submitted to different surface treatments

    Directory of Open Access Journals (Sweden)

    Adilson Yoshio Furuse

    2007-12-01

    Full Text Available The purpose of this study was to investigate the effect of different surface treatments on shear bond strength of saliva-contaminated resin-resin interfaces. Flat resin surfaces were fabricated. In the control group, no contamination or surface treatment was performed. The resin surfaces of the experimental groups were contaminated with saliva and air-dried, and then submitted to: (G1 rinsing with water and drying; (G2 application of an adhesive system; (G3 rinsing and drying, abrasion with finishing disks, etching and application of adhesive system; (G4 rinsing and drying, etching, application of silane and adhesive system. Resin cylinders were placed over the treated surfaces. The specimens were stored in water or ethanol. Shear bond strength tests were performed and the mode of failure was evaluated. Data were submitted to two-way ANOVA and Dunnett T3 test. Contamination of resin-resin interfaces with saliva significantly reduced shear strength, especially after prolonged storage (p<0.05. Similar values to the original bond strength were obtained after abrasion and application of adhesive (G3 or etching and application of silane and adhesive (G4. If contamination occurs, a surface treatment is required to guarantee an adequate interaction between the resin increments.

  8. Bond strength of resin-resin interfaces contaminated with saliva and submitted to different surface treatments

    DEFF Research Database (Denmark)

    Furuse, Adilson Yoshio; da Cunha, Leonardo Fernandes; Benetti, Ana Raquel

    2007-01-01

    of silane and adhesive system. Resin cylinders were placed over the treated surfaces. The specimens were stored in water or ethanol. Shear bond strength tests were performed and the mode of failure was evaluated. Data were submitted to two-way ANOVA and Dunnett T3 test. Contamination of resin...

  9. Ester Tuiksoo võitleb viina puhtuse eest / Ester Tuiksoo ; interv. Silja Lättemäe

    Index Scriptorium Estoniae

    Tuiksoo, Ester, 1965-

    2006-01-01

    Põllumajandusminister Ester Tuiksoo lubab Euroopa Liidu piiritusjookide määruse eelnõu arutusel kaitsta seisukohta, et viinaks tuleb pidada üksnes teraviljast või kartulist valmistatud piiritusjooki

  10. [Modified Mechanism of Cell Walls from Chinese Fir Treated with Low-Molecular-Weight Phenol Formaldehyde Resin].

    Science.gov (United States)

    Huang, Yan-hui; Fei, Ben-hua; Zhao, Rong-jun

    2015-12-01

    Study on the modified mechanism of wood cell walls, it is very important for improving treatment reagents, optimizing treatment technology, and enhancing wood density, mechanical properties, dimensional stability, and so on. Samples of plantation Chinese fir were treated gradually with synthesized water-soluble low-molecular-weight phenol formaldehyde (PF) resins under vacuum and pressure. The correlated physical and chemical properties of the treated and untreated reference samples were determined by X-ray diffractometer (XRD), Fourier transform infrared spectrometer (FTIR), and nuclear magnetic resonance spectrometer(NMR) (Using method of Cross Polarization/Magic Angle Spinning for continuous testing) with high precision and resolution. The results showed that, after treated with water-soluble low-molecular-weight PF resin, the average values of crystallinity from the treated samples were decreased obviously, and the average reduction rate was 12.67%, 11.91% and 6.26%, respectively. Comparing water-soluble, low-molecular-weight PF resin modified Chinese fir with untreated reference samples, no new chemical shifts and characteristic peaks of functional groups from esters, ethers, etc. were present by using FTIR and ¹³C NMR spectrum. It was considered that there was no distinct chemical reaction between the water-soluble low-molecular-weight PF resin and Chinese Fir cell walls. But water-soluble low-molecular-weight PF resin could enter into the structure relatively loose, large size spaces, relatively area large amorphous regions in cell walls of Chinese fir tracheids, and form physical filling, which resulting in the decreasing of relative crystallinity. This study has important reference value for the development of new wood modification reagents and the optimization of wood modification process. The findings also provide important theoretical foundation for further proving the modification mechanisms of wood cell walls and enriching the modified theories of

  11. ESTIMATION OF HYDROLYSIS RATE CONSTANTS OF CARBOXYLIC ACID ESTER AND PHOSPHATE ESTER COMPOUNDS IN AQUEOUS SYSTEMS FROM MOLECULAR STRUCTURE BY SPARC

    Science.gov (United States)

    SPARC (SPARC Performs Automated Reasoning in Chemistry) chemical reactivity models were extended to calculate hydrolysis rate constants for carboxylic acid ester and phosphate ester compounds in aqueous non- aqueous and systems strictly from molecular structure. The energy diffe...

  12. Neutral lipid biosynthesis in engineered Escherichia coli: jojoba oil-like wax esters and fatty acid butyl esters.

    Science.gov (United States)

    Kalscheuer, Rainer; Stöveken, Tim; Luftmann, Heinrich; Malkus, Ursula; Reichelt, Rudolf; Steinbüchel, Alexander

    2006-02-01

    Wax esters are esters of long-chain fatty acids and long-chain fatty alcohols which are of considerable commercial importance and are produced on a scale of 3 million tons per year. The oil from the jojoba plant (Simmondsia chinensis) is the main biological source of wax esters. Although it has a multitude of potential applications, the use of jojoba oil is restricted, due to its high price. In this study, we describe the establishment of heterologous wax ester biosynthesis in a recombinant Escherichia coli strain by coexpression of a fatty alcohol-producing bifunctional acyl-coenzyme A reductase from the jojoba plant and a bacterial wax ester synthase from Acinetobacter baylyi strain ADP1, catalyzing the esterification of fatty alcohols and coenzyme A thioesters of fatty acids. In the presence of oleate, jojoba oil-like wax esters such as palmityl oleate, palmityl palmitoleate, and oleyl oleate were produced, amounting to up to ca. 1% of the cellular dry weight. In addition to wax esters, fatty acid butyl esters were unexpectedly observed in the presence of oleate. The latter could be attributed to solvent residues of 1-butanol present in the medium component, Bacto tryptone. Neutral lipids produced in recombinant E. coli were accumulated as intracytoplasmic inclusions, demonstrating that the formation and structural integrity of bacterial lipid bodies do not require specific structural proteins. This is the first report on substantial biosynthesis and accumulation of neutral lipids in E. coli, which might open new perspectives for the biotechnological production of cheap jojoba oil equivalents from inexpensive resources employing recombinant microorganisms.

  13. Bulk-filled posterior resin restorations based on stress-decreasing resin technology

    DEFF Research Database (Denmark)

    van Dijken, Jan W.V.; Pallesen, Ulla

    2017-01-01

    This randomized study evaluated a flowable resin composite bulk-fill technique in posterior restorations and compared it intraindividually with a conventional 2-mm resin composite layering technique over a 6-yr follow-up period. Thirty-eight pairs of Class II restorations and 15 pairs of Class I...... restorations were placed in 38 adults. In all cavities a single-step self-etch adhesive (Xeno V) was applied. In the first cavity of each pair, the flowable resin composite (SDR) was placed, in bulk increments of up to 4 mm. The occlusal part was completed with a layer of nanohybrid resin composite (Ceram X...... mono). In the second cavity of each pair, the hybrid resin composite was placed in 2-mm increments. The restorations were evaluated using slightly modified US Public Health Service (USPHS) criteria at baseline and then annually for a time period of 6 yr. After 6 yr, 72 Class II restorations and 26...

  14. Side-chain crystallization in alkyl-substituted cellulose esters and hydroxypropyl cellulose esters.

    Science.gov (United States)

    Chen, Xi; Zheng, Nan; Wang, Qiao; Liu, Lingzhi; Men, Yongfeng

    2017-04-15

    The differences in side chain crystallization behavior between cellulose esters (CEs) and hydroxypropyl cellulose esters (HPCEs) were systematically investigated by a combination of differential scanning calorimetry (DSC) and small and wide-angle X-ray scattering techniques. DSC investigation indicated that under the same side chain length, the fusion enthalpy and the number of crystallized CH 2 of CEs were smaller than HPCEs. At the same time, their d-spacing and molecular arrangements were also different from each other. For the CEs, the side chains are perpendicular to the main chain, while the side chains most probably tend to tilt to main chain in the HPCEs as was evidenced by X-ray scattering results. The phenomenon can be understood as a consequence of different flexibility of attachment bridges in both kinds of side chain polymers and the steric hindrance of methyl group in the hydroxypropyl group in HPCEs. In addition, the added hydroxypropyl substituents make the side chain length increasing. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Extraction and Liquid Chromatography-Tandem Mass Spectrometry Detection of 3-Monochloropropanediol Esters and Glycidyl Esters in Infant Formula.

    Science.gov (United States)

    Leigh, Jessica K; MacMahon, Shaun

    2016-12-14

    A method was developed for the extraction of fatty acid esters of 3-chloro-1,2-propanediol (3-MCPD) and glycidol from infant formula, followed by quantitative analysis of the extracts using liquid chromatography-tandem mass spectrometry (LC-MS/MS). These process-induced chemical contaminants are found in refined vegetable oils, and studies have shown that they are potentially carcinogenic and/or genotoxic, making their presence in edible oils (and processed foods containing these oils) a potential health risk. The extraction procedure involves a liquid-liquid extraction, where powdered infant formula is dissolved in water and extracted with ethyl acetate. Following shaking, centrifugation, and drying of the organic phase, the resulting fat extract is cleaned-up using solid-phase extraction and analyzed by LC-MS/MS. Method performance was confirmed by verifying the percent recovery of each 3-MCPD and glycidyl ester in a homemade powdered infant formula reference material. Average ester recoveries in the reference material ranged from 84.9 to 109.0% (0.6-9.5% RSD). The method was also validated by fortifying three varieties of commercial infant formulas with a 3-MCPD and glycidyl ester solution. Average recoveries of the esters across all concentrations and varieties of infant formula ranged from 88.7 to 107.5% (1.0-9.5% RSD). Based on the validation results, this method is suitable for producing 3-MCPD and glycidyl ester occurrence data in all commercially available varieties of infant formula.

  16. Thermal rearrangement of novolak resins used in microlithography

    Science.gov (United States)

    Hardy, Ricky; Zampini, Anthony; Monaghan, Michael J.; O'Leary, Michael J.; Cardin, William J.; Eugster, Timothy J.

    1995-06-01

    Changes in phenolic-formaldehyde resin properties are described in terms of thermal exposure. At high temperature, resin molecular weight, dissolution properties and chemical composition change depending on the presence or absence of monomers. Without monomer in the resin melt at 220 degree(s)C, resin molecular weight increases with a corresponding decrease in dissolution rate. In the presence of monomer, molecular weight generally decreases. Dissolution rate may fluctuate depending on the monomer mixture. Three,five- Xylenol and 2,3,5-trimethylphenol co-monomers induced the most extreme changes in resin properties with thermal treatment. Resin degradation-recombination processes suggest a classical Friedel-Craft rearrangement mechanism.

  17. New bismaleimide matrix resins for graphite fiber composites

    Science.gov (United States)

    Hsu, M.-T. S.; Chen, T. S.; Parker, J. A.; Heimbuch, A. H.

    1985-01-01

    Two new bismaleimide resins based on the N,N'-m-phenylene-bis(m-amino-benzamide) structure have been synthesized and characterized. The mixtures of the two resins gave better handling, processing, mechanical, and thermal properties in graphite composites than did the individual resins. The mechanical strength of the cured graphite composites prepared from the 1:1 copolymer of the two bismaleimide resins was excellent at both ambient and elevated temperatures. The physical and mechanical properties of the composites from the new bismaleimide matrix resin systems are compared with conventional composites based on epoxy and other bismaleimide systems. The copolymer system provides another method for improving bismaleimide resins.

  18. Thermal cycling effects on adhesion of resin-bovine enamel junction among different composite resins.

    Science.gov (United States)

    Chen, Wen-Cheng; Ko, Chia-Ling; Wu, Hui-Yu; Lai, Pei-Ling; Shih, Chi-Jen

    2014-10-01

    Thermal cycling is used to mimic the changes in oral cavity temperature experienced by composite resins when used clinically. The purpose of this study is to assess the thermal cycling effects of in-house produced composite resin on bonding strength. The dicalcium phosphate anhydrous filler surfaces are modified using nanocrystals and silanization (w/NP/Si). The resin is compared with commercially available composite resins Filtek Z250, Z350, and glass ionomer restorative material GIC Fuji-II LC (control). Different composite resins were filled into the dental enamel of bovine teeth. The bond force and resin-enamel junction graphical structures of the samples were determined after thermal cycling between 5 and 55°C in deionized water for 600 cycles. After thermal cycling, the w/NP/Si 30wt%, 50wt% and Filtek Z250, Z350 groups showed higher shear forces than glass ionomer GIC, and w/NP/Si 50wt% had the highest shear force. Through SEM observations, more of the fillings with w/NP/Si 30wt% and w/NP/Si 50wt% groups flowed into the enamel tubule, forming closed tubules with the composite resins. The push-out force is proportional to the resin flow depth and uniformity. The push-out tubule pore and resin shear pattern is the most uniform and consistent in the w/NP/Si 50wt% group. Accordingly, this developed composite resin maintains great mechanical properties after thermal cycling. Thus, it has the potential to be used in a clinical setting when restoring non-carious cervical lesions. Copyright © 2014 Elsevier Ltd. All rights reserved.

  19. Sorption of organophosphate esters by carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Wei; Yan, Li [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); Duan, Jinming [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Jing, Chuanyong, E-mail: cyjing@rcees.ac.cn [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China)

    2014-05-01

    Graphical abstract: The interfacial interactions between the OPE molecules and CNTs. - Highlights: • Oxygen-containing groups on CNTs change the sorption property for OPEs. • Molecular configuration of OPEs has insignificant impact on their sorption. • Hydrophobic, π–π EDA and Brønsted acid–base interaction occurred between the CNTs and OPEs. - Abstract: Insights from the molecular-level mechanism of sorption of organophosphate esters (OPEs) on carbon nanotubes (CNTs) can further our understanding of the fate and transport of OPEs in the environment. The motivation for our study was to explore the sorption process of OPEs on multi-walled CNTs (MWCNTs), single-walled CNTs (SWCNTs) and their oxidized counterparts (O-MWCNTs and O-SWCNTs), and its molecular mechanism over a wide concentration range. The sorption isotherm results revealed that the hydrophobicity of OPEs dominated their affinities on a given CNT and the π–π electron donor–acceptor (EDA) interaction also played an important role in the sorption of aromatic OPEs. This π–π EDA interaction, verified with Raman and FT-IR spectroscopy, could restrict the radial vibration of SWCNTs and affect the deformation vibration γ(CH) bands of OPE molecules. The OPE surface coverage on CNTs, estimated using the nonlinear Dubinin–Ashtakhov model, indicated that the oxygen-containing functional groups on CNTs could interact with water molecules by H-bonding, resulting in a decrease in effective sorption sites. In addition, FTIR analysis also confirmed the occurrence of Brønsted acid–base interactions between OPEs and surface OH groups of SWCNTs. Our results should provide mechanistic insights into the sorption mechanism of OPE contaminants on CNTs.

  20. Smart Manufacturing Methods for Carbon/Vinyl Ester Structures

    National Research Council Canada - National Science Library

    Erickson, Curtis G

    2008-01-01

    .... Vacuum Assisted Resin Transfer Molding (VARTM) a common composite fabrication methodology for composite structures is extremely sensitive to the material systems used and the production set-up or design...

  1. Inhibition of platelet aggregation by diterpene acids from Pinus massoniana resin.

    Science.gov (United States)

    Cheung, H T; Fu, S L; Smal, M A

    1994-01-01

    The acidic fraction of the resin of Pinus massoniana Lamb. from China was converted to the p-nitrophenyl esters, and the esters separated by chromatography. The separated p-nitrophenyl esters were individually hydrolysed by potassium hydroxide in acetone-water at room temperature to 8 diterpene acids of the pimarane and abietane groups: pimaric acid (8(14),15-pimaradien-18-oic acid) (1), levopimaric acid (8(14),12-abietadien-18-oic acid) (2), palustric acid (8,13-abietadien-18-oic acid) (3), neobietic acid (8(14),13(15)-abietadien-18-oic acid) (4), abietic acid (7,13-abietadien-18-oic acid) (5), dehydroabietic acid (8,11,13-abietatrien-18-oic acid) (6), 7-oxodehydroabietic acid (7-oxo-8,11,13-abietatrien-18-oic acid) (7) and 7 alpha-hydroxydehydroabietic acid (7 alpha-hydroxy-8,11,13-abietatrien-18-oic acid) (8). The structure (and stereochemistry) of the diterpene acids were substantiated by nuclear magnetic resonance spectroscopy (proton and carbon-13, one and two dimensional), by mass spectrometry (electron impact and methane chemical ionization) and by rotation measurements. The 8 diterpene acids were tested for their ability to inhibit the aggregation of washed rabbit platelets induced by platelet activating factor (PAF), adenosine diphosphate (ADP) and by calcium ionophore A23187. With platelet aggregation induced by the latter two agonists, activities comparable with or higher than linolenic acid were given by the first 4 acids. With aggregation induced by PAF, the first 3 acids show activity, but at a level significantly lower than that of linolenic acid. Levopimaric acid has the highest activity among the diterpene acids tested. It is proposed that this activity is related to the folded shape of the molecule.

  2. Growth inhibitory properties of lactose fatty acid esters

    Directory of Open Access Journals (Sweden)

    Seung-Min Lee

    2017-11-01

    Full Text Available Sugar esters are biodegradable, nonionic surfactants which have microbial inhibitory properties. The influence of the fatty acid chain length on the microbial inhibitory properties of lactose esters was investigated in this study. Specifically, lactose monooctanoate (LMO, lactose monodecanoate (LMD, lactose monolaurate (LML and lactose monomyristate (LMM were synthesized and dissolved in both dimethyl sulfoxide (DMSO and ethanol. Minimum inhibitory concentrations (MIC and minimum bactericidal concentrations (MBC were determined in growth media. LML was the most effective ester, exhibiting MIC values of <0.05 to <5 mg/ml for each Gram-positive bacteria tested (Bacillus cereus, Mycobacterium KMS, Streptococcus suis, Listeria monocytogenes, Enterococcus faecalis, and Streptococcus mutans and MBC values of <3 to <5 mg/ml for B. cereus, M. KMS, S. suis, and L. monocytogenes. LMD showed MIC and MBC values of <1 to <5 mg/ml for B. cereus, M. KMS, S. suis, L. monocytogenes, and E. faecalis, with greater inhibition when dissolved in ethanol. LMM showed MIC and MBC values of <1 to <5 mg/ml for B. cereus, M. KMS, and S. suis. LMO was the least effective showing a MBC value of <5 mg/ml for only B. cereus, though MIC values for S. suis and L. monocytogenes were observed when dissolved in DMSO. B. cereus and S. suis were the most susceptible to the lactose esters tested, while S. mutans and E. faecalis were the most resilient and no esters were effective on Escherichia coli O157:H7. This research showed that lactose esters esterified with decanoic and lauric acids exhibited greater microbial inhibitory properties than lactose esters of octanoate and myristate against Gram-positive bacteria.

  3. Durability of resin-dentin bonds.

    Science.gov (United States)

    Shono, Y; Terashita, M; Shimada, J; Kozono, Y; Carvalho, R M; Russell, C M; Pashley, D H

    1999-01-01

    The purpose of this study was to determine if the durability of resin-dentin bonds could be evaluated more quickly if the bond specimen was divided into 1 x 1 x 8 mm beams incubated at 37 degrees C for a 90-day period. Extracted human third molars were prepared for bonding by removing the occlusal surface near the dento-enamel junction (superficial dentin group) or near the pulp (deep dentin group). The teeth were bonded either with MacBond, One Step or Clearfil Liner Bond 2, and then builtup to form a flat resin composite crown. After 24 hours in water, each buildup was vertically divided into slabs 1 mm thick, the top half of which was resin, with the bottom half as dentin. Each slab was then vertically sectioned at 1-mm increments to create 1 x 1 x 8-mm beams of resin-bonded dentin. They were incubated for 1 day or 90 days at 37 degrees C, followed by measurement of the tensile bond strengths. The results were analyzed by the Least-Squares Means method at the 95% confidence level. MacBond gave the highest (p durability of resin-dentin bonds.

  4. Processing of exhausted resins for Trino NPP,

    International Nuclear Information System (INIS)

    Benvenuto, F.; Bitetti, G.; Maggini, F.; Scarsi, G.

    2009-01-01

    Decomposition of organic compounds contained in the spent ion exchange resins is considered effective in reducing the waste volume. A system using the wet-oxidation process has been studied for the treatment of the spent resins stored at Trino Nuclear Power Plant owned by SOGIN. Compared with various processes for treating sludge and resin, the wet-oxidation system is rather simple and the process conditions are mild. Not contaminated ion exchange resin samples similar to those ones used in Trino NPP were processed by wet-oxidation and appropriate decomposition of the organic compounds was verified. After decomposition the residue can be solidified with cement for final disposal. When compared with direct solidification without decomposition, the number of waste packages can be significantly reduced. Additional measures for conditioning secondary waste products have also been studied, and their applicability to the Trino Nuclear Power Plant was verified. Some of conditions studied were specific to the Trino Nuclear Power Plant, but it is expected that the system will provide an effective solution for resin treatment at other Italian NPPs. (authors)

  5. EPICOR-II: a field leaching test of solidified radioactively loaded ion exchange resin

    Energy Technology Data Exchange (ETDEWEB)

    Davis, E.C.; Marshall, D.S.; Todd, R.A.; Craig, P.M.

    1986-08-01

    As part of an ongoing research program investigating the disposal of radioactive solid wastes in the environment' the Oak Ridge National Laboratory (ORNL) is participating with Argonne National Laboratory, the Idaho National Engineering Laboratory, and the Nuclear Regulatory Commission in a study of the leachability of solidified EPICOR-II ion-exchange resin under simulated disposal conditions. To simulate disposal, a group of five 2-m/sup 3/ soil lysimeters has been installed in Solid Waste Storage Area Six at ORNL, with each lysimeter containing a small sample of solidified resin at its center. Two solidification techniques are being investigated: a Portland cement and a vinyl ester-styrene treatment. During construction, soil moisture temperature cells were placed in each lysimeter, along with five porous ceramic tubes for sampling water near the waste source. A meteorological station was set up at the study site to monitor climatic conditions (primarily precipitation and air temperature), and a data acquisition system was installed to keep daily records of these meteorological parameters as well as lysimeter soil moisture and temperature conditions. This report documents the first year of the long-term field study and includes discussions of lysimeter installation, calibration of soil moisture probes, installation of the site meteorological station, and the results of the first-quarter sampling for radionuclides in lysimeter leachate. In addition, the data collection and processing system developed for this study is documented, and the results of the first three months of data collection are summarized in Appendix D.

  6. A new resin glycoside from Calystegia soldanella and its antiviral activity towards herpes.

    Science.gov (United States)

    Ono, Masateru; Kanemaru, Yukiyo; Yasuda, Shin; Okawa, Masafumi; Kinjo, Junei; Miyashita, Hiroyuki; Yokomizo, Kazumi; Yoshimitsu, Hitoshi; Nohara, Toshihiro

    2017-11-01

    A new resin glycoside, named calysolin XVIII (1), was isolated from the leaves, stems and roots of Calystegia soldanella Roem. et Schult. (Convolvulaceae). The structure of 1 was defined as 11S-jalapinolic acid 11-O-β-d-glucopyranosyl-(1 → 3)-O-(2-O-2S-methylbutyryl,4-O-3-hydroxy-2-methylenebutyryl)-α-l-rhamnopyranosyl-(1 → 2)-[O-β-d-glucopyranosyl-(1 → 6)-O-(34-di-O-2S-methylbutyryl)-β-d-glucopyranosyl-(1 → 3)]-O-β-d-glucopyranosyl-(1 → 2)-β-d-quinovopyranoside, intramolecular 1,2″'″'-ester on the basis of spectroscopic data. Compound 1 is the first known resin glycoside to feature 3-hydroxy-2-methylenebutyric acid as a component organic acid. In addition, 1 demonstrated an antiviral activity against herpes simplex virus type 1, with an IC 50 value 2.3 μM.

  7. Biodiesel production from acid oils and ethanol using a solid basic resin as catalyst

    International Nuclear Information System (INIS)

    Marchetti, J.M.; Errazu, A.F.

    2010-01-01

    In the search of an alternative fuel to substitute diesel fuel, biodiesel appears as one of the most promising sources of energy for diesel engines because of its environmental advantages and also due to the evolution of the petroleum market. Refined oil is the conventional raw material for the production of this biofuel; however, its major disadvantage is the high cost of its production. Therefore, frying oils, waste oils, crude oils and/or acid oils are being tested as alternative raw materials; nevertheless, there will be some problems if a homogeneous basic catalyst (NaOH) is employed due to the high amount of free fatty acid present in the raw oil. In this work, the transesterification reaction of acid oil using solid resin, Dowex monosphere 550 A, was studied as an alternative process. Ethanol was employed to have a natural and sustainable final product. The reaction temperature's effects, the initial amount of free fatty acid, the molar ratio of alcohol/oil and the type of catalyst (homogeneous or heterogeneous) over the main reaction are analyzed and their effects compared. The results obtained show that the solid resin is an alternative catalyst to be used to produce fatty acid ethyl esters (FAEEs) by a transesterification reaction with a final conversion over 90%. On the other hand, the time required to achieve this conversion is bigger than the one required using conventional technology which employs a homogeneous basic catalyst. This reaction time needs to be optimized. (author)

  8. Ponderosa pine resin defenses and growth: metrics matter.

    Science.gov (United States)

    Hood, Sharon; Sala, Anna

    2015-11-01

    Bark beetles (Coleoptera: Curculionidae, Scolytinae) cause widespread tree mortality in coniferous forests worldwide. Constitutive and induced host defenses are important factors in an individual tree's ability to survive an attack and in bottom-up regulation of bark beetle population dynamics, yet quantifying defense levels is often difficult. For example, in Pinus spp., resin flow is important for resistance to bark beetles but is extremely variable among individuals and within a season. While resin is produced and stored in resin ducts, the specific resin duct metrics that best correlate with resin flow remain unclear. The ability and timing of some pine species to produce induced resin is also not well understood. We investigated (i) the relationships between ponderosa pine (Pinus ponderosa Lawson & C. Lawson) resin flow and axial resin duct characteristics, tree growth and physiological variables, and (ii) if mechanical wounding induces ponderosa pine resin flow and resin ducts in the absence of bark beetles. Resin flow increased later in the growing season under moderate water stress and was highest in faster growing trees. The best predictors of resin flow were nonstandardized measures of resin ducts, resin duct size and total resin duct area, both of which increased with tree growth. However, while faster growing trees tended to produce more resin, models of resin flow using only tree growth were not statistically significant. Further, the standardized measures of resin ducts, density and duct area relative to xylem area, decreased with tree growth rate, indicating that slower growing trees invested more in resin duct defenses per unit area of radial growth, despite a tendency to produce less resin overall. We also found that mechanical wounding induced ponderosa pine defenses, but this response was slow. Resin flow increased after 28 days, and resin duct production did not increase until the following year. These slow induced responses may allow

  9. Application of ethyl esters and d3-methyl esters as internal standards for the gas chromatographic quantification of transesterified fatty acid methyl esters in food.

    Science.gov (United States)

    Thurnhofer, Saskia; Vetter, Walter

    2006-05-03

    Ethyl esters (FAEE) and trideuterium-labeled methyl esters (d3-FAME) of fatty acids were prepared and investigated regarding their suitability as internal standards (IS) for the determination of fatty acids as methyl esters (FAME). On CP-Sil 88, ethyl esters of odd-numbered fatty acids eluted approximately 0.5 min after the respective FAME, and only coelutions with minor FAME were observed. Depending on the problem, one or even many FAEE can be added as IS for the quantification of FAME by both GC-FID and GC-MS. By contrast, d3-FAME coeluted with FAME on the polar GC column, and the use of the former as IS requires application of GC-MS. In the SIM mode, m/z 77 and 90 are suggested for d3-methyl esters of saturated fatty acids, whereas m/z 88 and 101 are recommended for ethyl esters of saturated fatty acids. These m/z values give either no or very low response for FAME and can thus be used for the analysis of FAME in food by GC-MS in the SIM mode. Fatty acids in sunflower oil and mozzarella cheese were quantified using five saturated FAEE as IS. Gravimetric studies showed that the transesterification procedure could be carried out without of loss of fatty acids. GC-EI/MS full scan analysis was suitable for the quantitative determination of all unsaturated fatty acids in both food samples, whereas GC-EI/MS in the SIM mode was particularly valuable for quantifying minor fatty acids. The novel GC-EI/MS/SIM method using fatty acid ethyl esters as internal standards can be used to quantify individual fatty acids only, that is, without determination of all fatty acids (the common 100% method), although this is present. This was demonstrated by the exclusive quantification of selected fatty acids including methyl-branched fatty acids, erucic acid (18:1n-9trans), and polyunsaturated fatty acids in cod liver oil and goat's milk fat.

  10. Microshear bond strength of composite resins to enamel and porcelain substrates utilizing unfilled versus filled resins.

    Science.gov (United States)

    Najafi-Abrandabadi, Ahmad; Najafi-Abrandabadi, Siamak; Ghasemi, Amir; Kotick, Philip G

    2014-11-01

    Failures such as marginal discoloration and composite chipping are still the problems of tooth-colored restorations on the substrate of enamel and porcelain, which some of these problems are consequently as a result of failures in the bonding layer. Using filled resin has been recently introduced to increase the bond strength of this layer. The aim of this study was to compare the microshear bond strength (μ-SBS) of composite resins to enamel incubated in periods of 24 h and 9 months and porcelain with unfilled resin and flowable composites (filled resin). In this in vitro study, two groups of 75 enamel samples with different storage times (24 h and 9 months) and a group of 75 porcelain samples were used. They were divided into 5 experimental groups of 15 samples in each. Composite cylinders in tygon tubes were bonded on the surface of acid-etched enamel and pretreated porcelain. Wave, Wave MV, Wave HV, Grandioflow and Margin Bond were used as bonding agents. The μ-SBS was measured at the speed of 1.0 mm/min. The bond strengths were analyzed with one-way analysis of variance (ANOVA) test followed by Tukey test. P composites (filled resins) can be used instead of unfilled resins in bonding composite resins to enamel and porcelain substrates.

  11. Comparative study of resin sealant and resin modified glass ionomer as pit and fissure sealant

    Directory of Open Access Journals (Sweden)

    Shirin Malek

    2017-02-01

    Full Text Available The purpose of the present study was to compare the marginal integrity of resin modified glass ionomer cement with that of resin sealant, in vitro. Forty artificial pit and fissure cavities were prepared in occlusal surface of extracted premolar teeth by using ¼ round carbide bur. Cavities were condensed with artificial organic debris followed by cleaning with prophylaxis pumice brush and paste and then separated into two treatment groups. In Group A, 15 fissure cavities were sealed by resin sealant and in Group B, 15 fissure cavities were sealed by resin modified glass ionomer sealant. These specimens were subjected to thermo-cycling followed by dye penetration test. The remaining 5 cavities from each group were analyzed for debris score by the SEM. The results of the microleakage test showed that the efficacy of preventing microleakage of samples sealed by resin modified glass ionomer sealant was higher than the samples sealed by resin sealant. However, no significant differences were found. It can be concluded that use of resin modified glass ionomer sealant is a good alternative for sealing pits and fissures.

  12. Derivatization Technique To Identify Specifically Carbonyl Groups by Infrared Spectroscopy: Characterization of Photooxidative Aging Products in Terpenes and Terpeneous Resins.

    Science.gov (United States)

    Zumbühl, Stefan; Brändle, Andreas; Hochuli, Andreas; Scherrer, Nadim C; Caseri, Walter

    2017-02-07

    Analysis of bioorganic materials by infrared spectroscopy (FT-IR) is frequently limited due to overlapping of diagnostic bands from the various components, which poses a fundamental problem to this analytical technique. The distinction of oxidized di- and triterpenes, for example, is hindered by the superposition of similar absorption bands of carbonyl functional groups summing up to a broad, nondistinctive signal. This study presents a technique for selective fluorination of various carboxylic acids by exposure to gaseous sulfur tetrafluoride. The derivatization treatment leads to characteristic band shifts, allowing the separation of otherwise overlapping bands. Accordingly, the IR bands of primary acids, α,β-unsaturated acids, tertiary acids, peroxy acids, esters, ketones, and α,β-unsaturated ketones are split into distinct absorption bands. The capability of this method is demonstrated on the example of natural resins and their ingredients, which are commonly known to be susceptible to oxidation at ambient conditions. The derivatization method enables one to identify various carbonyl containing functional groups by infrared spectroscopy, even in complex mixtures of terpenes. It unveils previously hidden degradation reactions running in terpenes and natural resins exposed to artificial aging by irradiation with light. New insight is presented on the individual reaction pathways of the terpenes hydroxydammarenone and abietic acid as well as of natural resin varnishes made from dammar and colophony.

  13. Aging in CTBN modified epoxy resin stocks

    International Nuclear Information System (INIS)

    Creed, K.E. Jr.

    1979-01-01

    The cause of degradation in the glass transition temperature (T/sub G/) of a partially crystallized polymer was investigated. Sample epoxy resin filled capacitors were cured at 90 0 C for 24 hours, then stored at room atmospheric conditions. These showed typical degradation in T/sub G/ after storage for one month. One set of epoxy resin castings was stored at room atmosphere and another set was stored in a dry box at 0% relative humidity and 27 0 C. The samples at room atmospheric conditions showed typical degradation in T/sub G/, while the T/sub G/ for those stored in the dry box increased. Further tests were then made on epoxy resin castings at various curing temperatures and times at both room atmosphere and 0% humidity. Resulting data indicated that absorption of moisture during storage was the predominant cause of T/sub G/ degradation, with stress relaxation another, though smaller, contributing factor

  14. Resin injection in clays with high plasticity

    Science.gov (United States)

    Nowamooz, Hossein

    2016-11-01

    Regarding the injection process of polyurethane resins in clays with high plasticity, this paper presents the experimental results of the pressuremeter and cone penetration tests before and after injection. A very important increase in pressure limit or in soil resistance can be observed for all the studied depths close to the injection points. An analytical analysis for cylindrical pore cavity expansion in cohesive frictional soils obeying the Mohr-Coulomb criterion was then used to reproduce the pressuremeter tests before and after injection. The model parameters were calibrated by maintaining constant the elasticity parameters as well as the friction angel before and after injection. A significant increase in cohesion was observed because of soil densification after resin expansion. The estimated undrained cohesions, derived from the parameters of the Mohr-Coulomb criterion, were also compared with the cone penetration tests. Globally, the model predictions show the efficiency of resin injection in clay soils with high plasticity.

  15. Restoration of traumatized teeth with resin composites

    DEFF Research Database (Denmark)

    Pallesen, Ulla; van Dijken, Jan WV

    2018-01-01

    For a long time, the primary choice for initial restoration of a crown-fractured front tooth has been resin composite material. The restoration can in most cases be performed immediately after injury if there is no sign of periodontal injury. The method’s adhesive character is conservative to tooth......-structure and with minimal risk of pulpal complication. In addition, it offers an aesthetic solution to the patient immediately after an injury, which may bring a little comfort in a sad situation. The resin composite build-up is often changed or repaired a couple of times, before the tooth is restored with a porcelain...... present an aesthetic problem due to exposure of un-aesthetic crown-margins. The invasive permanent crown restorations are therefore often not suc-cessful on a long-term scale. On the other hand, a conservative direct restoration of an extensively fractured incisor crown with resin composite may...

  16. Investigations of toughening mechanisms of epoxy resins

    Science.gov (United States)

    Koenig, T.

    1986-01-01

    Composite material technology was applied to the solid rocket booster by the development of a carbon filament-epoxy resin case which yields a net increase of 4000 lbs. in payload in the shuttle. The question of reusability of the new composite tanks has not yet been answered and will depend on the toughness of the matrix resin. The present study was aimed at providing conditions whereby test specimens of the epoxy resin (EPON/85) and curing agents of systematically varied structures could be produced in a controlled manner. Three sets of conditions were found that might allow the isolation of the structural effects on toughness from the cure effects. The kinetic methods leading to the determination of these conditions are described.

  17. Effect of proximal box elevation with resin composite on marginal quality of resin composite inlays in vitro.

    Science.gov (United States)

    Roggendorf, Matthias J; Krämer, Norbert; Dippold, Christoph; Vosen, Vera E; Naumann, Michael; Jablonski-Momeni, Anahita; Frankenberger, Roland

    2012-12-01

    To evaluate marginal quality and resin-resin transition of lab made resin composite inlays in deep proximal cavities with and without 3 mm proximal box elevation (PBE) using resin composites before and after thermo-mechanical loading (TML). MOD cavities with one proximal box beneath the cementoenamel junction were prepared in 40 extracted human third molars. Proximal boxes ending in dentine were elevated 3 mm with different resin composites (G-Cem, Maxcem Elite as self-adhesive resin cements and Clearfil Majesty Posterior as restorative resin composite in one or three layers bonded with AdheSE), or left untreated. Clearfil Majesty Posterior inlays were luted with Syntac and Variolink II (n = 8). Marginal quality as well as the PBE-composite inlay interface was analyzed under an SEM using epoxy resin replicas before and after thermomechanical loading (100,000 × 50 N and 2500 thermocylces between +5 °C and +55 °C). Bonding resin composite inlays directly to dentine showed similar amounts of gap-free margins in dentine compared to PBE applied in three consecutive layers (p > 0.05). The groups with self-adhesive resin cements for PBE exhibited significantly more gaps in dentine (p < 0.05). With layered resin composite, PBE is effective in indirect resin composite bonding to deep proximal boxes. Self-adhesive resin cements are not suitable for this indication. Copyright © 2012 Elsevier Ltd. All rights reserved.

  18. 76 FR 8774 - Granular Polytetrafluoroethylene Resin From Japan

    Science.gov (United States)

    2011-02-15

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Granular Polytetrafluoroethylene Resin From Japan AGENCY: United States International Trade... polytetrafluoroethylene resin from Japan would be likely to lead to continuation or recurrence of material injury. On...

  19. Composite resin fillings and inlays: An 11-year evaluation

    DEFF Research Database (Denmark)

    Pallesen, U.; Qvist, V.

    2003-01-01

    Clinical trial, composite resin, direct restorations, indirect restorations, long-term behaviour, posterior teeth......Clinical trial, composite resin, direct restorations, indirect restorations, long-term behaviour, posterior teeth...

  20. Development of 3-methoxy-4-benzyloxybenzyl alcohol (MBBA) resin ...

    Indian Academy of Sciences (India)

    step sequence under microwave irradiation involving the reaction of commercially available Merrifield resin with vanillin, followed by reduction with sodium borohydride. MBBA resin was treated with bromides in the presence of sodium hydride to ...

  1. Fluorinated Alkyl Ether Epoxy Resin Compositions and Applications Thereof

    Science.gov (United States)

    Wohl, Christopher J. (Inventor); Connell, John W. (Inventor); Smith, Joseph G. (Inventor); Siochi, Emilie J. (Inventor); Gardner, John M. (Inventor); Palmieri, Frank M. (Inventor)

    2017-01-01

    Epoxy resin compositions prepared using amino terminated fluoro alkyl ethers. The epoxy resin compositions exhibit low surface adhesion properties making them useful as coatings, paints, moldings, adhesives, and fiber reinforced composites.

  2. Biphenyl liquid crystalline epoxy resin as a low-shrinkage resin-based dental restorative nanocomposite.

    Science.gov (United States)

    Hsu, Sheng-Hao; Chen, Rung-Shu; Chang, Yuan-Ling; Chen, Min-Huey; Cheng, Kuo-Chung; Su, Wei-Fang

    2012-11-01

    Low-shrinkage resin-based photocurable liquid crystalline epoxy nanocomposite has been investigated with regard to its application as a dental restoration material. The nanocomposite consists of an organic matrix and an inorganic reinforcing filler. The organic matrix is made of liquid crystalline biphenyl epoxy resin (BP), an epoxy resin consisting of cyclohexylmethyl-3,4-epoxycyclohexanecarboxylate (ECH), the photoinitiator 4-octylphenyl phenyliodonium hexafluoroantimonate and the photosensitizer champhorquinone. The inorganic filler is silica nanoparticles (∼70-100 nm). The nanoparticles were modified by an epoxy silane of γ-glycidoxypropyltrimethoxysilane to be compatible with the organic matrix and to chemically bond with the organic matrix after photo curing. By incorporating the BP liquid crystalline (LC) epoxy resin into conventional ECH epoxy resin, the nanocomposite has improved hardness, flexural modulus, water absorption and coefficient of thermal expansion. Although the incorporation of silica filler may dilute the reinforcing effect of crystalline BP, a high silica filler content (∼42 vol.%) was found to increase the physical and chemical properties of the nanocomposite due to the formation of unique microstructures. The microstructure of nanoparticle embedded layers was observed in the nanocomposite using scanning and transmission electron microscopy. This unique microstructure indicates that the crystalline BP and nanoparticles support each other and result in outstanding mechanical properties. The crystalline BP in the LC epoxy resin-based nanocomposite was partially melted during exothermic photopolymerization, and the resin expanded via an order-to-disorder transition. Thus, the post-gelation shrinkage of the LC epoxy resin-based nanocomposite is greatly reduced, ∼50.6% less than in commercialized methacrylate resin-based composites. This LC epoxy nanocomposite demonstrates good physical and chemical properties and good biocompatibility

  3. Phytosterol ester constituents affect micellar cholesterol solubility in model bile.

    Science.gov (United States)

    Brown, Andrew W; Hang, Jiliang; Dussault, Patrick H; Carr, Timothy P

    2010-09-01

    Plant sterols and stanols (phytosterols) and their esters are nutraceuticals that lower LDL cholesterol, but the mechanisms of action are not fully understood. We hypothesized that intact esters and simulated hydrolysis products of esters (phytosterols and fatty acids in equal ratios) would differentially affect the solubility of cholesterol in model bile mixed micelles in vitro. Sodium salts of glycine- and taurine-conjugated bile acids were sonicated with phosphatidylcholine and either sterol esters or combinations of sterols and fatty acids to determine the amount of cholesterol solubilized into micelles. Intact sterol esters did not solubilize into micelles, nor did they alter cholesterol solubility. However, free sterols and fatty acids altered cholesterol solubility independently (no interaction effect). Equal contents of cholesterol and either campesterol, stigmasterol, sitosterol, or stigmastanol (sitostanol) decreased cholesterol solubility in micelles by approximately 50% compared to no phytosterol present, with stigmasterol performing slightly better than sitosterol. Phytosterols competed with cholesterol in a dose-dependent manner, demonstrating a 1:1 M substitution of phytosterol for cholesterol in micelle preparations. Unsaturated fatty acids increased the micelle solubility of sterols as compared with saturated or no fatty acids. No differences were detected in the size of the model micelles. Together, these data indicate that stigmasterol combined with saturated fatty acids may be more effective at lowering cholesterol micelle solubility in vivo.

  4. Development of continuous deglycerolisation reactor for ethyl ester production

    Directory of Open Access Journals (Sweden)

    Ruamporn Nikhom

    2014-12-01

    Full Text Available In this work, the development of continuous deglycerolisation (CD reactor for ethyl ester production was investigated to improve the ethyl ester conversion. The device to assist separation of glycerol, in the CD unit, integrates transesterification (mixing zone and separation (settling zone into one unit. For reversible transesterification, removing glycerol during reaction can drive the equilibrium to the product side in order to achieve high conversion. Two models of device to assist separation of glycerol have been carried out to investigate the suitable conditions for ethyl ester production. Results showed that the fin-type model could separate higher amount of glycerol from the reaction system in order to achieve high transesterification conversion. The suitable conditions found in this study were: molar ratio of oil to ethanol of 1:5, KOCH3 concentration of 1.6 %wt. retention time of 15 min and reaction temperature of 70°C. At these conditions, ethyl ester’s purity and yield were 97.3%wt. and 92.0%wt., respectively. In addition, the fuel properties of the final ethyl ester product met the biodiesel standard for methyl ester which specified by Department of Energy Business.

  5. The influence of resin flexural modulus on the magnitude of ceramic strengthening.

    LENUS (Irish Health Repository)

    Fleming, Garry J P

    2012-07-01

    The aim was to determine the magnitude of ceramic resin-strengthening with resin-based materials with varying flexural moduli using a regression technique to assess the theoretical strengthening at a \\'zero\\' resin-coating thickness. The hypothesis tested was that experimentally, increasing resin flexural modulus results in increased resin-strengthening observed at a theoretical \\'zero\\' resin-coating thickness.

  6. Determination of testosterone esters and estradiol esters in bovine and porcine blood serum.

    Science.gov (United States)

    Rejtharová, Martina; Rejthar, Libor; Čačková, Katarína

    2017-04-01

    Monitoring of steroid esters in blood serum is desirable in order to detect the possible illegal use of natural hormones as growth promoters. A method for the determination of testosterone propionate, testosterone benzoate, testosterone isocaproate, testosterone decanoate and estradiol benzoate in bovine and porcine blood serum was developed. The procedure consists of protein precipitation and removal of phospholipids using a HybridSPE®-Phospholipid column followed by clean-up on a hydrophilic modified styrene polymer Supel TM -Select HLB column and LC-MS/MS measurement. The method was validated according to Commission Decision 2002/657/EC. Decision limits for all analytes were observed in the range 5-30 pg ml - 1 . The method was shown to be robust for bovine and porcine serum analyses and can be applied for both screening and confirmatory determination in routine residue monitoring.

  7. Performances and improvement of copper-hydrazine complexation deoxidising resin

    International Nuclear Information System (INIS)

    Liu Fenfen; Zhang Hao; Sun Haijun; Liu Xiaojie

    2012-01-01

    Copper-hydrazine complexation deoxidising resin is tested to examine its performances including effluent water quality and capacity of deoxidisation. By the means of changing the resin type and regeneration, the deoxidising capacity of the resin can be improved to 13 times more than before. At the same time, physical performances of the resin are also greatly improved while maintaining its velocity of deoxidisation and effluent quality. (authors)

  8. Recovery of tretrachloroaurate through ion exchange with Dowex 11 resin

    International Nuclear Information System (INIS)

    Alguacil, F.J.

    1998-01-01

    The recovery of the tretrachloroaurate complex by the anionic ion exchange resin Dowex 11 has been studied. The kinetics of gold adsorption were dependent of both gold and resin concentrations and temperature. The adsorption isotherm can be described by the expression Q=kC''n. The loaded resin could be eluted by an acidic thiourea solution at 20 degree centigree. After several adsorption-elution cycles there is not any apparent loss in the adsorption properties of the resin. (Author) 6 refs

  9. Gamma-irradiation on cured glycidyl amino-epoxy resin

    International Nuclear Information System (INIS)

    Yang, Ting; Wei, Chengsha; Liu, Hewen

    2010-01-01

    ITER is an international project to design and build an experimental fusion reactor based on the superconductive 'tokamak' concept. Amounts of epoxy resin are used in the superconductive tokamak device as impregnant resins, insulation breaks, etc. Resistance to ionizing radiation is a demanding performance of those epoxy resins. In this work, we study the effects of γ-irradiation on the mechanical properties and chemical structures of glycidyl amino-epoxy resins

  10. Synthesis of a boron modified phenolic resin

    Directory of Open Access Journals (Sweden)

    Aparecida M. Kawamoto

    2010-08-01

    Full Text Available Phenolic resin has long been used as matrix for composites mainly because of its flame retardant behavior and high char yield after pyrolysis, which results in a self supporting structure. The addition of ceramic powders, such as SiC and B4C, as fillers to the phenolic resin, results in better thermo-oxidative stability, but as drawbacks, it has poor homogeneity, adhesion and processing difficulties during molding of the composites. The addition of single elements, such as boron, silicon and phosphorus in the main backbone of the thermo-set resin is a new strategy to obtain special high performance resins, which results in higher mechanical properties, avoiding the drawbacks of simply adding fillers, which results in enhanced thermo-oxidative stability compared to conventional phenol-formaldehyde resins. Therefore, the product can have several applications, including the use as ablative thermal protection for thermo-structural composites. This work describes the preparation of a boron-modified phenolic resin (BPR using salicyl alcohol and boric acid. The reaction was performed in refluxing toluene for a period of four hours, which produced a very high viscosity amber resin in 90% yield.The final structure of the compound, the boric acid double, substituted at the hydroxyl group of the aromatic ring, was determined with the help of the Infrared Spectroscopy, ¹H-NMR, TGA-DSC and boron elemental analysis. The absorption band of the group B-O at 1349 cm ˉ¹ can be visualized at the FT-IR spectrum. ¹H-NMR spectra showed peaks at 4.97-5.04 ppm and 3.60-3.90 ppm assigned to belong to CH2OH groups from the alcohol. The elemental analysis was also performed for boron determination.The product has also been tested in carbon and silicon fibers composite for the use in thermal structure. The results of the tests showed composites with superior mechanical properties when compared with the conventional phenolic resin.

  11. Development of amino resin for paint formulation: Copolymerization ...

    African Journals Online (AJOL)

    SERVER

    2007-06-18

    Jun 18, 2007 ... The moisture uptake of the different resin films was determined gravimetrically. Known weights of each of ... as the moisture intake by the resin (Barminas and Osemeahon,. 2006). All determinations were performed ... Therefore during the condensation reactions of methylol urea resins into polymer chains, ...

  12. Facile synthesis of allyl resinate monomer in an aqueous solution ...

    Indian Academy of Sciences (India)

    as oligomer products such as inks and coatings. Com- pared with the oligomer from fossil resources such as acrylic resins and styrene resins, we believe the intro- duction of the resin structure into polymer products can provide specific mechanical properties, such as hardness and flexibility. GC analysis of each component ...

  13. 21 CFR 872.3670 - Resin impression tray material.

    Science.gov (United States)

    2010-04-01

    ... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3670 Resin impression tray material. (a) Identification. Resin impression tray material is a device intended for use in a two-step dental mold fabricating... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Resin impression tray material. 872.3670 Section...

  14. Evaluation of some anionic exchange resins as potential tablet ...

    African Journals Online (AJOL)

    The effect of resin concentration and compression force on the properties of tablets using the selected resin was investigated. In addition, the disintegrant efficacy of the selected resin in the tablet formulations containing either a basic drug, e.g., dextromethorphan hydrobromide (DMP), or an acidic drug, e.g., diclofenac ...

  15. 21 CFR 173.40 - Molecular sieve resins.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Molecular sieve resins. 173.40 Section 173.40 Food... Polymer Substances and Polymer Adjuvants for Food Treatment § 173.40 Molecular sieve resins. Molecular sieve resins may be safely used in the processing of food under the following prescribed conditions: (a...

  16. 75 FR 67105 - Granular Polytetrafluoroethylene Resin From Italy and Japan

    Science.gov (United States)

    2010-11-01

    ... COMMISSION Granular Polytetrafluoroethylene Resin From Italy and Japan AGENCY: United States International... granular polytetrafluoroethylene resin from Italy and Japan. SUMMARY: The Commission hereby gives notice... polytetrafluoroethylene resin from Italy and Japan would be likely to lead to continuation or recurrence of material...

  17. Photosensitive filler minimizes internal stresses in epoxy resins

    Science.gov (United States)

    Dillon, J. N.

    1967-01-01

    Photosensitive filler is added to curable epoxy resins to minimize stress from internal shrinkage during curing or polymerization. Cinnamic acid resins and cinnamal ketones may be added in the amount of 1 to 3 percent by weight of the resin mixture.

  18. Color change of composite resins subjected to accelerated artificial aging.

    Science.gov (United States)

    Tornavoi, Denise Cremonezzi; Agnelli, José Augusto Marcondes; Panzeri, Heitor; Dos Reis, Andréa Cândido

    2013-01-01

    The aim of this study was to evaluate the influence of accelerated artificial aging (AAA) on the color change of composite resins used in dentistry. Three composite resins were evaluated: Two microhybrids and one hybrid of higher viscosity, with different amounts and sizes of filler particles, shades C2 and B2. A total of 54 specimens were obtained (18 for each composite resin), made of a Teflon matrix (15 mm in diameter and 2 mm in height). The color measurements were obtained with a Spectrophotometer, (PCB 6807 BYK Gardner) before and after AAA. Data were submitted to the Kolmogorov-Smirnov test (α >0.05), ANOVA and Tukey test (α composite resins with the same shades was analyzed. All composite resins showed unacceptable color changes after AAA (ΔE > 3). Considering the variable ∆E, it was observed that the color tone C2 was already statistically different for the microhybrid composite resin prior to AAA (P composite resins (P composite resin group, before aging the composite resin hybrid of higher viscosity B2 showed the highest color variation rate and microhybrid with zirconium/silica C2 showed the lowest. All composite resins presented unacceptable color changes after 382 h of aging and different composite resins with same hue, presented different colors before being subjected to the aging process (B2 and C2) and after (B2). It was also observed color difference within a group of the same composite resin and same hue.

  19. Development of radiation-curable resin based on natural rubber

    International Nuclear Information System (INIS)

    Dahlan Mohd; Abdul Ghani Harun

    1993-01-01

    A new radiation curable resin based on natural rubber has been developed. The resin was based on the reaction between low molecular weight epoxidised natural rubber and acrylic acid. When formulated with reactive monomers and photoinitiator, it solidified upon irradiation with UV light. The resin may find applications in coating for cellulosic-based substrates and pressure-sensitive adhesive

  20. Resin impregnation of cellulose nanofibril films facilitated by water swelling

    Science.gov (United States)

    Yan Qing; Ronald Sabo; Zhiyong Cai; Yiqiang Wu

    2013-01-01

    Flexible composite films were produced by impregnating aqueous phenol formaldehyde (PF) resin into water-swollen cellulose nanofibril (CNF) films. CNF films were prepared using a pressurized filtration method in combination with freeze drying. The freeze-dried films were swollen with water then impregnated with PF resin by soaking in aqueous resin solutions of varying...

  1. 21 CFR 177.2355 - Mineral reinforced nylon resins.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Mineral reinforced nylon resins. 177.2355 Section... as Components of Articles Intended for Repeated Use § 177.2355 Mineral reinforced nylon resins. Mineral reinforced nylon resins identified in paragraph (a) of this section may be safely used as articles...

  2. 21 CFR 177.2260 - Filters, resin-bonded.

    Science.gov (United States)

    2010-04-01

    ... a pH above 5.0. (j) Resin-bonded filters conforming with the specifications of paragraph (j) (1) of... bulk quantities of nonalcoholic, aqueous foods having a pH of 5.0 or below. (k) Resin-bonded filters...: List of Substances and Limitations (1) Fibers: Cellulose pulp. Cotton. Nylon. (From nylon resins...

  3. 40 CFR 721.5908 - Modified phenolic resin (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Modified phenolic resin (generic). 721... Substances § 721.5908 Modified phenolic resin (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as modified phenolic resin (PMN P...

  4. 40 CFR 721.2673 - Aromatic epoxide resin (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Aromatic epoxide resin (generic). 721... Substances § 721.2673 Aromatic epoxide resin (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as aromatic epoxide resin (PMN P...

  5. Treatment of White Spot Lesions with Icon (Resin Infiltration)

    Science.gov (United States)

    2017-03-23

    FROM: 59 MDW/SGVU SUBJECT: Professional Presentation Approval 8 MAR2017 1. Your paper, entitled T reatment of White Spot Lesions with Icon ( Resin ... Resin Infiltration) 6. TITLE OF MATERIAL TO BE PUBLISHED OR PRESENTED: Treatment of White Spot lesions with Icon ( Resin In filtration) 7. FUNDING

  6. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573.120 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid resin...

  7. 40 CFR 721.9499 - Modified silicone resin.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Modified silicone resin. 721.9499... Substances § 721.9499 Modified silicone resin. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a modified silicone resin (PMN P-96-1649) is...

  8. 40 CFR 721.4380 - Modified hydrocarbon resin.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Modified hydrocarbon resin. 721.4380... Substances § 721.4380 Modified hydrocarbon resin. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a modified hydrocarbon resin (P-91-1418) is...

  9. 40 CFR 721.5905 - Modified phenolic resin (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Modified phenolic resin (generic). 721... Substances § 721.5905 Modified phenolic resin (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a modified phenolic resin (PMN...

  10. 21 CFR 872.3200 - Resin tooth bonding agent.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Resin tooth bonding agent. 872.3200 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3200 Resin tooth bonding agent. (a) Identification. A resin tooth bonding agent is a device material, such as methylmethacrylate, intended to be painted...

  11. 40 CFR 721.5762 - Aromatic aldehyde phenolic resin (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Aromatic aldehyde phenolic resin... Specific Chemical Substances § 721.5762 Aromatic aldehyde phenolic resin (generic). (a) Chemical substance... aromatic aldehyde phenolic resin (PMN P-01-573) is subject to reporting under this section for the...

  12. 21 CFR 872.3690 - Tooth shade resin material.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Tooth shade resin material. 872.3690 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3690 Tooth shade resin material. (a) Identification. Tooth shade resin material is a device composed of materials such as bisphenol-A glycidyl...

  13. Development of 3-methoxy-4-benzyloxybenzyl alcohol (MBBA) resin ...

    Indian Academy of Sciences (India)

    Administrator

    Abstract. 3-Methoxy-4-benzyloxybenzyl alcohol (MBBA) resin was synthesized by a two-step se- quence under microwave irradiation involving the reaction of commercially available Merrifield resin with vanillin, followed by reduction with sodium borohydride. MBBA resin was treated with bromides in the presence of sodium ...

  14. Color change of composite resins subjected to accelerated artificial aging

    Directory of Open Access Journals (Sweden)

    Denise Cremonezzi Tornavoi

    2013-01-01

    Conclusions: All composite resins presented unacceptable color changes after 382 h of aging and different composite resins with same hue, presented different colors before being subjected to the aging process (B2 and C2 and after (B2. It was also observed color difference within a group of the same composite resin and same hue.

  15. 21 CFR 177.2510 - Polyvinylidene fluoride resins.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polyvinylidene fluoride resins. 177.2510 Section... as Components of Articles Intended for Repeated Use § 177.2510 Polyvinylidene fluoride resins. Polyvinylidene fluoride resins may be safely used as articles or components of articles intended for repeated use...

  16. 21 CFR 872.3300 - Hydrophilic resin coating for dentures.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Hydrophilic resin coating for dentures. 872.3300... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3300 Hydrophilic resin coating for dentures. (a) Identification. A hydrophilic resin coating for dentures is a device that consists of a water...

  17. 21 CFR 872.3310 - Coating material for resin fillings.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Coating material for resin fillings. 872.3310... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3310 Coating material for resin fillings. (a) Identification. A coating material for resin fillings is a device intended to be applied to the...

  18. 76 FR 4936 - Granular Polytetrafluoroethylene Resin From Italy

    Science.gov (United States)

    2011-01-27

    ... Polytetrafluoroethylene Resin From Italy AGENCY: United States International Trade Commission. ACTION: Revised schedule... granular polytetrafluoroethylene resin (``granular PTFE resin'') from Italy. DATES: Effective Date: January... from Italy and Japan (75 FR 67082-67083 and 67105-67108, November 1, 2010). However, Commerce's notice...

  19. 76 FR 39896 - Granular Polytetrafluoroethylene Resin From Italy

    Science.gov (United States)

    2011-07-07

    ... Polytetrafluoroethylene Resin From Italy Determination On the basis of the record \\1\\ developed in the subject five-year... granular polytetrafluoroethylene resin from Italy would be likely to lead to continuation or recurrence of... Polytetrafluoroethylene Resin from Italy: Investigation No. 731-TA-385 (Third Review). By order of the Commission. Issued...

  20. 21 CFR 872.3820 - Root canal filling resin.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Root canal filling resin. 872.3820 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3820 Root canal filling resin. (a) Identification. A root canal filling resin is a device composed of material, such as methylmethacrylate, intended...

  1. 40 CFR 721.3135 - Phosphorous modified epoxy resin (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Phosphorous modified epoxy resin... Specific Chemical Substances § 721.3135 Phosphorous modified epoxy resin (generic). (a) Chemical substance... phosphorous modified epoxy resin (PMNs P-00-992 and P-01-471) is subject to reporting under this section for...

  2. 40 CFR 721.2752 - Epoxy resin containing phosphorus (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Epoxy resin containing phosphorus... Specific Chemical Substances § 721.2752 Epoxy resin containing phosphorus (generic). (a) Chemical substance... epoxy resin containing phosphorus (PMN P-00-912) is subject to reporting under this section for the...

  3. 40 CFR 721.2755 - Cycloaliphatic epoxy resin (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Cycloaliphatic epoxy resin (generic... Substances § 721.2755 Cycloaliphatic epoxy resin (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as cycloaliphatic epoxy resin (PMN...

  4. Boric ester-type molten salt via dehydrocoupling reaction.

    Science.gov (United States)

    Matsumi, Noriyoshi; Toyota, Yoshiyuki; Joshi, Prerna; Puneet, Puhup; Vedarajan, Raman; Takekawa, Toshihiro

    2014-11-14

    Novel boric ester-type molten salt was prepared using 1-(2-hydroxyethyl)-3-methylimidazolium chloride as a key starting material. After an ion exchange reaction of 1-(2-hydroxyethyl)-3-methylimidazolium chloride with lithium (bis-(trifluoromethanesulfonyl) imide) (LiNTf2), the resulting 1-(2-hydroxyethyl)-3-methylimidazolium NTf2 was reacted with 9-borabicyclo[3.3.1]nonane (9-BBN) to give the desired boric ester-type molten salt in a moderate yield. The structure of the boric ester-type molten salt was supported by 1H-, 13C-, 11B- and 19F-NMR spectra. In the presence of two different kinds of lithium salts, the matrices showed an ionic conductivity in the range of 1.1 × 10⁻⁴-1.6 × 10⁻⁵ S cm⁻¹ at 51 °C. This was higher than other organoboron molten salts ever reported.

  5. Saliva-catalyzed hydrolysis of a ketobemidone ester prodrug

    DEFF Research Database (Denmark)

    Hansen, L.B.; Christrup, Lona Louring; Bundgaard, H.

    1992-01-01

    Saliva enzyme-catalysed hydrolysis of ester prodrugs or drugs containing sensitive ester groups may be a limiting factor for the buccal absorption of such compounds. Using the isopropyl carbonate ester of ketobemidone as a model substance of a hydrolysis-sensitive prodrug the esterase activity...... of human saliva has been characterized as a function of various factors. The esterase activity was found to decrease rapidly upon storage of the saliva at 37°C. The activity increased with increasing pH in the range 4.5-7.4 and with increasing salivation flow rate up to a rate of 0.9 ml min. Under resting...... conditions, the flow rate was about 0.2 ml min which implied a greatly decreased esterase activity. The activity was highest after fasting and decreased after intake of a meal. The intraindividual variation in the saliva esterase activity was small whereas a larger interindividual variation was found....

  6. Long-Acting Diclofenac Ester Prodrugs for Joint Injection

    DEFF Research Database (Denmark)

    Mertz, Nina; Larsen, Susan Weng; Kristensen, Jesper

    2016-01-01

    A prodrug approach for local and sustained diclofenac action after injection into joints based on ester prodrugs having a pH-dependent solubility is presented. Inherent ester prodrug properties influencing the duration of action include their pH-dependent solubility and charge state, as well...... as susceptibility to undergo esterase facilitated hydrolysis. In this study, physicochemical properties and pH rate profiles of 3 diclofenac ester prodrugs differing with respect to the spacer carbon chain length between the drug and the imidazole-based promoiety were determined and a rate equation for prodrug...... degradation in aqueous solution in the pH range 1-10 was derived. In the pH range 6-10, the prodrugs were subject to parallel degradation to yield diclofenac and an indolinone derivative. The prodrug degradation was found to be about 6-fold faster in 80% (vol/vol) human plasma as compared to 80% (vol...

  7. Isolation and pharmacological activity of phenylpropanoid esters from Marrubium vulgare.

    Science.gov (United States)

    Sahpaz, Sevser; Garbacki, Nancy; Tits, Monique; Bailleul, Francois

    2002-03-01

    The isolation and identification of major phenylpropanoid esters from Marrubium vulgare: (+) (E)-caffeoyl-L-malic acid 1, acteoside 2, forsythoside B 3, arenarioside 4, ballotetroside 5, as well as their anti-inflammatory activity are reported for the first time. We evaluated the inhibitory effects of these five compounds on cyclooxygenase (Cox) catalysed prostaglandin biosynthesis activity. Only the glycosidic phenylpropanoid esters showed an inhibitory activity towards the Cox-2 enzyme and three of them: acteoside 2, forsythoside B 3, arenarioside 4, exhibited higher inhibitory potencies on Cox-2 than on Cox-1. These results are of interest, as Cox-2 is mainly associated with inflammation and the Cox-1 inhibition with adverse side effects often observed with non-steroidal anti-inflammatory drugs. The occurrence of these phenylpropanoid esters could also explain some other pharmacological properties of M. vulgare.

  8. Boric Ester-Type Molten Salt via Dehydrocoupling Reaction

    Directory of Open Access Journals (Sweden)

    Noriyoshi Matsumi

    2014-11-01

    Full Text Available Novel boric ester-type molten salt was prepared using 1-(2-hydroxyethyl-3-methylimidazolium chloride as a key starting material. After an ion exchange reaction of 1-(2-hydroxyethyl-3-methylimidazolium chloride with lithium (bis-(trifluoromethanesulfonyl imide (LiNTf2, the resulting 1-(2-hydroxyethyl-3-methylimidazolium NTf2 was reacted with 9-borabicyclo[3.3.1]nonane (9-BBN to give the desired boric ester-type molten salt in a moderate yield. The structure of the boric ester-type molten salt was supported by 1H-, 13C-, 11B- and 19F-NMR spectra. In the presence of two different kinds of lithium salts, the matrices showed an ionic conductivity in the range of 1.1 × 10−4–1.6 × 10−5 S cm−1 at 51 °C. This was higher than other organoboron molten salts ever reported.

  9. Three new fatty acid esters from the mushroom Boletus pseudocalopus.

    Science.gov (United States)

    Kim, Ki Hyun; Choi, Sang Un; Lee, Kang Ro

    2012-06-01

    A bioassay-guided fractionation and chemical investigation of a MeOH extract of the Korean wild mushroom Boletus pseudocalopus resulted in the identification of three new fatty acid esters, named calopusins A-C (1-3), along with two known fatty acid methyl esters (4-5). These new compounds are structurally unique fatty acid esters with a 2,3-butanediol moiety. Their structures were elucidated through 1D- and 2D-NMR spectroscopic data and GC-MS analysis as well as a modified Mosher's method. The new compounds 1-3 showed significant inhibitory activity against the proliferation of the tested cancer cell lines with IC(50) values in the range 2.77-12.51 μM.

  10. A Comparison Study: The New Extended Shelf Life Isopropyl Ester PMR Technology versus The Traditional Methyl Ester PMR Approach

    Science.gov (United States)

    Alston, William B.; Scheiman, Daniel A.; Sivko, Gloria S.

    2005-01-01

    Polymerization of Monomeric Reactants (PMR) monomer solutions and carbon cloth prepregs of PMR II-50 and VCAP-75 were prepared using both the traditional limited shelf life methanol based PMR approach and a novel extended shelf life isopropanol based PMR approach. The methyl ester and isopropyl ester based PMR monomer solutions and PMR prepregs were aged for up to four years at freezer and room temperatures. The aging products formed were monitored using high pressure liquid chromatography (HPLC). The composite processing flow characteristics and volatile contents of the aged prepregs were also correlated versus room temperature storage time. Composite processing cycles were developed and six ply cloth laminates were fabricated with prepregs after various extended room temperature storage times. The composites were then evaluated for glass transition temperature (Tg), thermal decomposition temperature (Td), initial flexural strength (FS) and modulus (FM), long term (1000 hours at 316 C) thermal oxidative stability (TOS), and retention of FS and FM after 1000 hours aging at 316 C. The results for each ester system were comparable. Freezer storage was found to prevent the formation of aging products for both ester systems. Room temperature storage of the novel isopropyl ester system increased PMR monomer solution and PMR prepreg shelf life by at least an order of magnitude while maintaining composite properties.

  11. Application of Ester based Drilling Fluid for Shale Gas Drilling

    Science.gov (United States)

    Sauki, Arina; Safwan Zazarli Shah, Mohamad; Bakar, Wan Zairani Wan

    2015-05-01

    Water based mud is the most commonly used mud in drilling operation. However, it is ineffective when dealing with water-sensitive shale that can lead to shale hydration, consequently wellbore instability is compromised. The alternative way to deal with this kind of shale is using synthetic-based mud (SBM) or oil-based mud (OBM). OBM is the best option in terms of technical requirement. Nevertheless, it is toxic and will create environmental problems when it is discharged to onshore or offshore environment. SBM is safer than the OBM. The aim of this research is to formulate a drilling mud system that can carry out its essential functions for shale gas drilling to avoid borehole instability. Ester based SBM has been chosen for the mud formulation. The ester used is methyl-ester C12-C14 derived from palm oil. The best formulation of ester-based drilling fluid was selected by manipulating the oil-water ratio content in the mud which are 70/30, 80/20 and 90/10 respectively. The feasibility of using this mud for shale gas drilling was investigated by measuring the rheological properties, shale reactivity and toxicity of the mud and the results were compared with a few types of OBM and WBM. The best rheological performance can be seen at 80/20 oil-water ratio of ester based mud. The findings revealed that the rheological performance of ester based mud is comparable with the excellent performance of sarapar based OBM and about 80% better than the WBM in terms of fluid loss. Apart from that, it is less toxic than other types of OBM which can maintain 60% prawn's survival even after 96 hours exposure in 100,000 ppm of mud concentration in artificial seawater.

  12. Functionalization of epoxy esters with alcohols as stoichiometric reagents.

    Science.gov (United States)

    Pavlović, Dona; Modec, Barbara; Dolenc, Darko

    2015-01-01

    Glycidyl esters, frequently employed as reactive groups on polymeric supports, were functionalized with alcohols as stoichiometric reagents, yielding β-alkoxyalcohols. Among the solvents studied, best results were obtained in ethers in the presence of a strong proton acid as a catalyst. Alcohols include simple alkanols, diols, protected polyols, 3-butyn-1-ol 3-hydroxypropanenitrile and cholesterol. This protocol represents a convenient way for introduction of various functionalities onto epoxy-functionalized polymers. Under the reaction conditions, some side reactions take place, mostly due to the reactive ester group and water present in the reaction mixture.

  13. Low-melt Viscosity Polyimide Resins for Resin Transfer Molding (RTM) II

    Science.gov (United States)

    Chuang, Kathy C.; Criss, Jim M.; Mintz, Eric A.; Scheiman, Daniel A.; Nguyen, Baochau N.; McCorkle, Linda S.

    2007-01-01

    A series of polyimide resins with low-melt viscosities in the range of 10-30 poise and high glass transition temperatures (Tg s) of 330-370 C were developed for resin transfer molding (RTM) applications. These polyimide resins were formulated from 2,3,3 ,4 -biphenyltetracarboxylic dianhydride (a-BPDA) with 4-phenylethynylphthalic anhydride endcaps along with either 3,4 - oxyaniline (3,4 -ODA), 3,4 -methylenedianiline, (3,4 -MDA) or 3,3 -methylenedianiline (3,3 -MDA). These polyimides had pot lives of 30-60 minutes at 260-280 C, enabling the successful fabrication of T650-35 carbon fiber reinforced composites via RTM process. The viscosity profiles of the polyimide resins and the mechanical properties of the polyimide carbon fiber composites will be discussed.

  14. Resin Flow in Fiber Preformed by Vacuum Assisted Resin Transfer Molding with Flexible Tools

    Directory of Open Access Journals (Sweden)

    M.M. Shokrieh

    2008-12-01

    Full Text Available Vacuum assisted resin transfer molding, as a sub-branch of RTM is a method of manufacturing composite specimens. Considering the industrial development of this method, different modified techniques are designed to improve its performance. Among these techniques, using a half flexible mold is regarded as an important method. In this work, dominant equations of resin flow through the mold in polar coordinates are solved analytically. Based on this approach, closed-form solutions have been presented for different parameters such as thickness variation of preformed fiber, resin pressure, resin velocity and fiber volume fraction as functions of two variables, namely, time and the distance from injection port. After verification of the approach employed in this work, the results are presented. Important parameters influencing the quality and the rate production are studied in detail.

  15. 21 CFR 177.1580 - Polycarbonate resins.

    Science.gov (United States)

    2010-04-01

    ... condensation of 4,4′-iso-propylidenediphenol and carbonyl chloride to which may have been added certain optional adjuvant substances required in the production of the resins; or by (2) The reaction of molten 4,4′-iso-propylidenediphenol with molten diphenyl carbonate in the presence of the disodium salt of 4,4...

  16. Effect of Resin Extract from Commiphora swynnertonii

    African Journals Online (AJOL)

    Dr Olaleye

    of Commiphora swynnertonii resin on biochemical parameters in rats was investigated. Sixty rats were ... significantly elevated protein and albumin levels but had no significant effect on bilirubin and all the liver enzymes in the rats. These findings are ... hypoglycemic and hypolipidemic effects against high fat diet- induced ...

  17. Microbial treatment of ion exchange resins

    International Nuclear Information System (INIS)

    Kouznetsov, A.; Kniazev, O.

    2001-01-01

    A bioavailability of ion exchange resins to a microbial destruction as one of the alternative methods of compacting used ionites from the nuclear fuel manufacturing cycle enterprises has been investigated. The bio-destruction was studied after a preliminary chemical treatment or without it. A sensitivity of the ion exchange resins (including highly acidic cationite KU-2-8) to the microbial destruction by heterotrophic and chemo-litho-trophic microorganisms under aerobic conditions was shown in principle. The biodegradation of the original polymer is possible in the presence of the water soluble fraction of the resin obtained after its treatment by Fenton reagent and accelerated in the presence of Mn-ions in optimal concentration 1-2 g of Mn per liter of medium. Thus, the process of bio-destruction of ionite polymer by heterotrophic microorganisms can be compared with the bio-destruction of lignin or humic substances. The optimum parameters of bio-destruction and microorganisms used must be different for resins with different functional groups. (authors)

  18. Liquid Resins-Based Additive Manufacturing

    Science.gov (United States)

    Wang, Fei; Wang, Fuke

    In this review, additive manufacturing technologies using liquid resins as materials are reviewed from the perspective of printing technologies and materials. Most importantly, recent progress of new printing technologies and printers as well as novel printing materials and their applications are summarized, based on which potential future research directions are discussed at the end of this review.

  19. Evaluation of resins for use in brachytherapy

    International Nuclear Information System (INIS)

    Carvalho, Luiz Claudio F.M. Garcia; Ferraz, Wilmar Barbosa; Chrcanovic, Bruno Ramos; Santos, Ana Maria M.

    2011-01-01

    Brachytherapy is an advanced cancer treatment where radioactive seeds or sources are placed near or directly into the tumor thus reducing the radiation exposure in the surrounding healthy tissues. Prostate cancer can be treated with interstitial brachytherapy in initial stage of the disease in which tiny radioactive seeds with cylindrical geometry are used. Several kinds of seeds have been developed in order to obtain a better dose distribution around them and with a lower cost manufacturing. These seeds consist of an encapsulation, a radionuclide carrier, and X-ray marker. Among the materials that have potential for innovation in the construction of seeds, biocompatible resins appear as an important option. In this paper, we present some characterization results with Fourier transform infrared spectroscopic (FTIR) and ultraviolet-visible spectroscopy (UV-vis) performed on two types of resins in which curing temperatures for each one were varied as also the results of coatings with these resins under titanium substrates. Interactions of these resins in contact with the simulated body fluid were evaluated by atomic force microscopy, scanning electron microscopy, and energy dispersive X-ray spectroscopy. (author)

  20. Biodegradation of acrylic based resins: A review.

    Science.gov (United States)

    Bettencourt, Ana F; Neves, Cristina B; de Almeida, Marise S; Pinheiro, Lídia M; Oliveira, Sofia Arantes e; Lopes, Luís P; Castro, Matilde F

    2010-05-01

    The development of different types of materials with application in dentistry is an area of intense growth and research, due to its importance in oral health. Among the different materials there are the acrylic based resins that have been extensively used either in restorations or in dentures. The objective of this manuscript was to review the acrylic based resins biodegradation phenomena. Specific attention was given to the causes and consequences of materials degradation under the oral environment. Information from scientific full papers, reviews or abstracts published from 1963 to date were included in the review. Published material was searched in dental literature using general and specialist databases, like the PubMED database. Published studies regarding the description of biodegradation mechanisms, in vitro and in vivo release experiments and cell based studies conducted on acrylic based resins or their components were evaluated. Studies related to the effect of biodegradation on the physical and mechanical properties of the materials were also analyzed. Different factors such as saliva characteristics, chewing or thermal and chemical dietary changes may be responsible for the biodegradation of acrylic based resins. Release of potential toxic compounds from the material and change on their physical and mechanical properties are the major consequences of biodegradation. Increasing concern arises from potential toxic effects of biodegradation products under clinical application thus justifying an intensive research in this area. 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  1. 21 CFR 177.1585 - Polyestercarbonate resins.

    Science.gov (United States)

    2010-04-01

    .... Copies are available from the Office of Premarket Approval, Center for Food Safety and Applied Nutrition... examined at the Center for Food Safety and Applied Nutrition's Library, Food and Drug Administration, 5100...) Extractives limitations. The polyestercarbonate resins to be tested shall be ground or cut into small...

  2. Facile synthesis of hypercrosslinked resins via chloromethylation ...

    Indian Academy of Sciences (India)

    Administrator

    Abstract. A sort of non-polystyrene type hypercrosslinked resin was firstly synthesized through chloromethyla- tion of simple aryl molecules (benzene, toluene, naphthalene, diphenyl), succedent continuous Friedel–Crafts alkylation polymerization and post-crosslinking reaction. The chemical and porous structures of these ...

  3. Triterpenes from the resin of Boswellia neglecta

    African Journals Online (AJOL)

    Boswellia neglecta S. Moore (Burseraceae) is found in Bale, Gamo Gofa, Hararghe and Sidamo. (Ethiopia) and also in neighbouring countries such as Kenya, Somalia, Tanzania and Uganda [1]. The plant produces aromatic resins used widely as incense known as “Dakara” (Oromifa),. "Borena Etan" (Amharic) or "Borena ...

  4. Extended Resin Composite Restorations: Techniques and Procedures

    NARCIS (Netherlands)

    Loomans, B.A.C.; Hilton, T.

    2016-01-01

    This article gives an overview of the state of the art of different restorative treatment procedures and techniques needed for placing extended posterior resin composite restorations. Clinical aspects related to the procedure are discussed and reviewed based on the current literature, such as the

  5. Microbial treatment of ion exchange resins

    Energy Technology Data Exchange (ETDEWEB)

    Kouznetsov, A.; Kniazev, O. [D. Mendeleyev University of Chemical Technology of Russia, Dept. Biotechnology, Mocow (Russian Federation)

    2001-07-01

    A bioavailability of ion exchange resins to a microbial destruction as one of the alternative methods of compacting used ionites from the nuclear fuel manufacturing cycle enterprises has been investigated. The bio-destruction was studied after a preliminary chemical treatment or without it. A sensitivity of the ion exchange resins (including highly acidic cationite KU-2-8) to the microbial destruction by heterotrophic and chemo-litho-trophic microorganisms under aerobic conditions was shown in principle. The biodegradation of the original polymer is possible in the presence of the water soluble fraction of the resin obtained after its treatment by Fenton reagent and accelerated in the presence of Mn-ions in optimal concentration 1-2 g of Mn per liter of medium. Thus, the process of bio-destruction of ionite polymer by heterotrophic microorganisms can be compared with the bio-destruction of lignin or humic substances. The optimum parameters of bio-destruction and microorganisms used must be different for resins with different functional groups. (authors)

  6. Evaluation of resins for use in brachytherapy

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Luiz Claudio F.M. Garcia; Ferraz, Wilmar Barbosa; Chrcanovic, Bruno Ramos; Santos, Ana Maria M., E-mail: ferrazw@cdtn.b, E-mail: amms@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2011-07-01

    Brachytherapy is an advanced cancer treatment where radioactive seeds or sources are placed near or directly into the tumor thus reducing the radiation exposure in the surrounding healthy tissues. Prostate cancer can be treated with interstitial brachytherapy in initial stage of the disease in which tiny radioactive seeds with cylindrical geometry are used. Several kinds of seeds have been developed in order to obtain a better dose distribution around them and with a lower cost manufacturing. These seeds consist of an encapsulation, a radionuclide carrier, and X-ray marker. Among the materials that have potential for innovation in the construction of seeds, biocompatible resins appear as an important option. In this paper, we present some characterization results with Fourier transform infrared spectroscopic (FTIR) and ultraviolet-visible spectroscopy (UV-vis) performed on two types of resins in which curing temperatures for each one were varied as also the results of coatings with these resins under titanium substrates. Interactions of these resins in contact with the simulated body fluid were evaluated by atomic force microscopy, scanning electron microscopy, and energy dispersive X-ray spectroscopy. (author)

  7. 21 CFR 177.1555 - Polyarylate resins.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polyarylate resins. 177.1555 Section 177.1555 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... in contact with all foods except beverages containing more than 8 volume percent ethanol under...

  8. Electron-beam curing of epoxy resins

    Indian Academy of Sciences (India)

    Electron-beam (e-beam) induced polymerization of epoxy resins proceeds via cationic mechanism in presence of suitable photoinitiator. Despite good thermal properties and significant processing advantages, epoxy-based composites manufactured using e-beam curing suffer from low compressive strength, poor ...

  9. 21 CFR 177.1595 - Polyetherimide resin.

    Science.gov (United States)

    2010-04-01

    ... and Applied Nutrition (HFS-200), Food and Drug Administration, 5100 Paint Branch Pkwy., College Park... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polyetherimide resin. 177.1595 Section 177.1595 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD...

  10. Method for curing alkyd resin compositions by applying ionizing radiation

    International Nuclear Information System (INIS)

    Watanabe, T.; Murata, K.; Maruyama, T.

    1975-01-01

    An alkyd resin composition is prepared by dissolving a polymerizable alkyd resin having from 10 to 50 percent of oil length into a vinyl monomer. The polymerizable alkyd resin is obtained by a half-esterification reaction of an acid anhydride having a polymerizable unsaturated group and an alkyd resin modified with conjugated unsaturated oil having at least one reactive hydroxyl group per one molecule. The alkyd resin composition thus obtained is coated on an article, and ionizing radiation is applied on the article to cure the coated film thereon. (U.S.)

  11. PENGARUH RASIO MOL REAKTAN DAN LAMA SULFONASI TERHADAP KARAKTERISTIK METHYL ESTER SULFONIC (MES DARI METIL ESTER MINYAK SAWIT

    Directory of Open Access Journals (Sweden)

    Sri Hidayati

    2016-04-01

    Full Text Available An experiment of sulfonation process of methyl ester to produce methyl ester sulfonates (MES was caried out using methyl ester palm oil in factorial design and NaHSO as sulfonating agent with variation of ratio mol NaHSO : methyl ester (1:1.25, 1:1.5, 1:1.75 and 1:2 and sulfonation time (3 hour (L1, 4.5 hour (L2 and 6 hour (L3. The result showed that the best sulfonation condition present in 1:1,5 mol ratio and sulfonation time of 4,5 hour. The best characteristic of MES was produced emulsion stability of 68.25%, acid value of 2.57 mg KOH/g, iod value 10.91 g 1od/100 g sample, interfacial tension of 1.806 dyne/cm at MES concentration of 1% (w/w. The optimal salinity occured at concentration of 20.000 ppm which 1FT value of 0.0055 dyne/cm. Heating at a temperature of 800 C for 30 days with the addition of 2 3. Keywords: MES, sulfonation, NaHSO   ABSTRAK Sebuah penelitian tentang proses produksi metil ester sulfonat menggunakan bahan baku metil ester minyak kelapa sawit dilakukan secara faktorial menggunakan NaHSO sebagai agen pensulfonasi dengan variasi rasio mol NaHSO 1:1,25, 1:1,5, 1:1,75 dan 1:2 dan lama sulfonasi.dengan variasi 3; 45; dan 6 jam. Hasil penelitian menunjukkan bahwa kondisi proses sulfonasi terbaik terdapat pada rasio metil ester dan mol reaktan 1:1,5 dan  lama reaksi  4,5 jam dan suhu reaksi lOOoC yang menghasilkan nilai stabilitas emulsi 68,25%, bilangan asam 2,57 mg KOH/g sampel, bilangan iod 10,91 g 1od/100 g sampel. Konsentrasi metil ester sulfonat MES terbaik untuk menghasilkan 1FT terendah adalah 1% (b/b yaitu 1,806 dyne/cm, salinitas optimal terjadi pada 20.000 ppm NaCl dengan nilai 1FT 0,0055 dyne/cm. 0,098 dyne/cm. Kata kunci: MES, proses sulfonasi, NaHSO

  12. Hydrocarbon-soluble epoxidized fatty acid esters as lubricity modifiers for lubricating oils

    Energy Technology Data Exchange (ETDEWEB)

    Coupland, K.; Smith, C.R.

    1981-01-13

    Hydrocarbon-soluble epoxidized fatty acid esters prepared by the epoxidation of unsaturated carboxylic acid esters are useful hydrocarbon additives. Their incorporation into a suitable hydrocarbon functional fluid such as a lubricating oil gives improved antiwear and antifriction properties.

  13. Synthesis and characterizations of melamine-based epoxy resins.

    Science.gov (United States)

    Ricciotti, Laura; Roviello, Giuseppina; Tarallo, Oreste; Borbone, Fabio; Ferone, Claudio; Colangelo, Francesco; Catauro, Michelina; Cioffi, Raffaele

    2013-09-05

    A new, easy and cost-effective synthetic procedure for the preparation of thermosetting melamine-based epoxy resins is reported. By this innovative synthetic method, different kinds of resins can be obtained just by mixing the reagents in the presence of a catalyst without solvent and with mild curing conditions. Two types of resins were synthesized using melamine and a glycidyl derivative (resins I) or by adding a silane derivative (resin II). The resins were characterized by means of chemical-physical and thermal techniques. Experimental results show that all the prepared resins have a good thermal stability, but differ for their mechanical properties: resin I exhibits remarkable stiffness with a storage modulus value up to 830 MPa at room temperature, while lower storage moduli were found for resin II, indicating that the presence of silane groups could enhance the flexibility of these materials. The resins show a pot life higher than 30 min, which makes these resins good candidates for practical applications. The functionalization with silane terminations can be exploited in the formulation of hybrid organic-inorganic composite materials.

  14. Component composition of essential oils and ultrastructure of secretory cells of resin channel needles Juniperus communis (Cupressaceae

    Directory of Open Access Journals (Sweden)

    N. V. Gerling

    2015-12-01

    Full Text Available The results of determining the qualitative and quantitative composition of essential oil Juniperus communis, growing under the canopy of spruce blueberry sphagnum subzone middle taiga. Juniperus communis essential oil is liquid light yellow color. The content of essential oil was 0.46 % in shoots with needles. 37 substances of components identified. Mass fraction of components in the essential oil of Juniperus communis reached 89 %. The highest percentage of occupied fraction of monoterpenes (82.3 %, the proportion of sesquiterpenes less than 0.5 % of the total composition of essential oils, alcohols 3.5 and 0.7 % esters. In monoterpenes fraction predominant α-pinene (24.5–32.6 %, β-pinene (15–20.3 % and α-phellandrene (6.4–8.8 %. Essential oil of Juniperus communis is characterized by high content of monoterpenoids in contrast to other conifers of the taiga zone. All stages of biosynthesis essential oils occur in the epithelial cells of the resin channel (terpenoidogennyh cells. An oval shape have epithelial cells of the resin channel needles in transverse sections the Juniperus communis, which is situated vacuole in the center. Large number of lipid globules (up to 40 noted in the hyaloplasm of explored cells. Leucoplasts surrounded by membranes of smooth endoplasmic reticulum in cross sections of epithelial cells in resin channel of juniper. Endoplasmic reticulum is poorly developed in epithelial cells, which corresponds to the low content of sesquiterpenes in the needles during the study period. Development of large leucoplasts and large number of mitochondria associated with predominance of synthesis monoterpenoids the in the epithelium cells resin channel.

  15. Effects of resins on asphaltene self-association and solubility

    Energy Technology Data Exchange (ETDEWEB)

    Yarranton, H.W.; Fox, W.A.; Svrcek, W.Y. [Calgary Univ., AB (Canada). Dept. of Chemical and Petroleum Engineering

    2007-10-15

    This paper described a method of modelling the self-association and precipitation of asphaltenes and resins. Self-association was assessed using vapor pressure osmometry (VPO) measurements of asphaltene and resin mixtures. A modified asphaltene self-association model was used to fit and interpret data. The molar mass distribution of the asphaltene-resin aggregates was characterized. Precipitation data were obtained by measuring asphaltenes and resins in solutions of asphaltenes, resins, toluene, and heptane. The molar mass distribution was then used as an input to the regular solution model. Results of the study suggested that resins participate in asphaltene self-association. It was concluded that both asphaltenes and resins are best characterized as a combined pseudo-component with a single molar mass distribution of the aggregated species. 30 refs., 4 tabs., 5 figs.

  16. FDI report on adverse reactions to resin-based materials.

    Science.gov (United States)

    Fan, P L; Meyer, D M

    2007-02-01

    Resin-based restorative materials are considered safe for the vast majority of dental patients. Although constituent chemicals such as monomers, accelerators and initiators can potentially leach out of cured resin-based materials after placement, adverse reactions to these chemicals are rare and reaction symptoms commonly subside after removal of the materials. Dentists should be aware of the rare possibility that patients could have adverse reactions to constituents of resin-based materials and be vigilant in observing any adverse reactions after restoration placement. Dentists should also be cognisant of patient complaints about adverse reactions that may result from components of resin-based materials. To minimise monomer leaching and any potential risk of dermatological reactions, resin-based materials should be adequately cured. Dental health care workers should avoid direct skin contact with uncured resin-based materials. Latex and vinyl gloves do not provide adequate barrier protection to the monomers in resin-based materials.

  17. Lubricity of bio-based lubricant derived from chemically modified jatropha methyl ester

    OpenAIRE

    N.W.M. Zulkifli; H.H. Masjuki; M.A. Kalam; R. Yunus; S.S.N. Azman

    2014-01-01

    Many studies have been undertaken with a view to using chemically modified vegetable oil as a bio-based lubricant. This research focused on tribological properties of trimethylolpropane (TMP) ester, which is derived from renewable resource. This TMP ester was produced from jatropha methyl ester; it is biodegradable and has high lubricity properties. Two different conditions of lubrication are being investigated: extreme pressure and anti-wear. It was found that the TMP ester (Jatropha) has be...

  18. Comparison of Mechanical Properties of Resin Composites with Resin Modified Glass Ionomers

    Directory of Open Access Journals (Sweden)

    Taha NA

    2015-06-01

    Full Text Available Statement of Problem: There are controversial reports regarding physical and mechanical properties of resin composites and glass ionomer cements. Some revealed higher strength and hardness for resin composites while others showed a comparable value for glass ionomer cements. Evaluation of mechanical properties of different types of resin composites in comparison with resin modified glass ionomers is not widely studied. Objectives: To measure and compare the flexural strength and Vickers hardness of three resin composites and two resins modified glass ionomer cements before and after ageing. Materials and Methods: Three resin composites, i.e. Filtek Supreme XTE (3M ESPE, Ice (SDI, Gradia (GC, and two resins modified glass ionomers, i.e. Fuji II LC (GC and Riva Light Cure (SDI, were selected. Ten barshaped specimens were prepared for each material and cured using LED curing light. After 24 hours storage in distilled water at 37oC, the specimens were randomly divided into two equal groups (n=5. The first group was tested as a baseline and the second group was restored at 37oC for another 29 days. Flexural strength was performed by four-point bending test using universal testing machine at crosshead speed of 0.5mm/min, and the maximum load at failure was recorded. The specimen’s halves were used for evaluating Vickers hardness, using a Digital Hardness Tester (300 g/15 sec and the Vickers hardness number (VHN was recorded. Data were analyzed using one-way analysis of variance (ANOVA, Tukey’s and student’s t-test. Results: After 24 hours of immersion, the highest hardness number was found for Filtek Supreme and Ice and the highest flexural strength was obtained for Gradia. After 30 days of storage, hardness of Fuji II LC and Gradia showed a significant decrease; flexural strength of Ice and Fuji II LC revealed a significant increase while Gradia and Filtek Supreme showed a significant decrease. Conclusions: Resin modified glass ionomers showed

  19. Hydrolytic Stability of Boronate Ester-Linked Covalent Organic Frameworks

    KAUST Repository

    Li, Huifang

    2018-01-30

    The stability of covalent organic frameworks (COFs) is essential to their applications. However, the common boronate ester-linked COFs are susceptible to attack by nucleophiles (such as water molecules) at the electron-deficient boron sites. To provide an understanding of the hydrolytic stability of the representative boronate ester-linked COF-5 and of the associated hydrolysis mechanisms, density functional theory (DFT) calculations were performed to characterize the hydrolysis reactions of the molecule formed by the condensation of 1,4-phenylenebis(boronic acid) (PBBA) and 2,3,6,7,10,11-hexahydroxytriphenylene (HHTP) monomers; two cases were considered, one dealing with the freestanding molecule and the other with the molecule interacting with COF layers. It was found that the boronate ester (B–O) bond dissociation, which requires one H2O molecule, has a relatively high energy barrier of 22.3 kcal mol−1. However, the presence of an additional H2O molecule significantly accelerates hydrolysis by reducing the energy barrier by a factor of 3. Importantly, the hydrolysis of boronate ester bonds situated in a COF environment follows reaction pathways that are different and have increased energy barriers. These results point to an enhanced hydrolytic stability of COF-5 crystals.

  20. Effect of a novel insulinotropic agent, succinic acid monoethyl ester ...

    Indian Academy of Sciences (India)

    Madhu

    In the present study, the effect of succinic acid monoethyl ester (EMS) on the pattern of lipids and lipoproteins in streptozotocin-nicotinamide induced type 2 diabetes was investigated. Type 2 diabetes was induced in male Wistar rats by single intraperitoneal injection (i.p.) of 45 mg/kg streptozotocin, 15 min after the i.p ...

  1. Production of both esters and biogas from Mexican poppy | Singh ...

    African Journals Online (AJOL)

    This paper details a dynamic evaluation of a procedure for extracting both, ester and biogas from seeds and waste of Mexican poppy (Argemone mexicana) using simple and inexpensive technique. Results showed that A. mexicana seed contains 30% oil. Through the process of transestrification, oil extracted from seed, ...

  2. Enzymatic synthesis of oligo- and polysaccharide fatty acid esters

    NARCIS (Netherlands)

    Broek, van den L.A.M.; Boeriu, C.G.

    2013-01-01

    Amphiphilic oligo- and polysaccharides (e.g. polysaccharide alkyl or alkyl-aryl esters) form a new class of polymers with exceptional properties. They function as polymeric surfactants, whilst maintaining most of the properties of the starting polymeric material such as emulsifying, gelling, and

  3. Synthesis and physical properties of petroselinic based estolide esters

    Science.gov (United States)

    A new series of petroselinic (Coriandrum sativum L.)-based estolide 2-ethylhexyl (2-EH) esters were synthesized, as the capping material varied in length and in degrees of unsaturation, in a perchloric acid catalyzed one-pot process with the esterification process incorporated into an in situ second...

  4. Catalytic Synthesis of Ethyl Ester From Some Common Oils ...

    African Journals Online (AJOL)

    Catalytic conversion of ethanol to fatty acid ethyl esters (FAEE) was carried out by homogeneous and heterogeneous transesterification of melon seed, shea butter and neem seed oils using NaOH, KOH and 5wt%CaO/Al2O3 catalyst systems respectively. Oil content of the seeds from n-hexane or hot water extract ranged ...

  5. Effect of Sucrose Esters on the Physicochemical Properties of Wheat ...

    African Journals Online (AJOL)

    In addition, the structure and thermodynamic properties of the modified starch were analyzed by Fourier transform infrared spectroscopy (FITR), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). Results: The properties of wheat starch changed greatly by adding different sucrose esters to their ...

  6. A method for the deprotection of alkylpinacolyl boronate esters.

    Science.gov (United States)

    Sun, Jing; Perfetti, Michael T; Santos, Webster L

    2011-05-06

    A two-step procedure for deprotection of alkylpinacolyl boronate esters via transesterification with diethanolamine followed by hydrolysis was successfully developed with the advantages of tolerance to various functional groups, short reaction time, and ease of product isolation. © 2011 American Chemical Society

  7. Ethyl ester purpurine-18 from Gossypium mustelinum (Malvaceae)

    International Nuclear Information System (INIS)

    Silva, Tania Maria Sarmento; Camara, Celso Amorim; Barbosa-Filho, Jose Maria; Giulietti, Ana Maria

    2010-01-01

    The phaeophorbide ethyl ester named Purpurine-18 and the flavonoids quercetin and kaempferol were obtained by chromatographic procedures from the chloroform fraction of aerial parts of Gossypium mustelinum. The structure of these compound was determined by NMR, IR and mass spectra data analysis. This is the first occurrence of this compound in Angiosperm. (author)

  8. Effect of a novel insulinotropic agent, succinic acid monoethyl ester ...

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Biosciences; Volume 31; Issue 5. Effect of a novel insulinotropic agent, succinic acid monoethyl ester, on lipids and lipoproteins levels in rats with streptozotocin-nicotinamideinduced type 2 diabetes. Ramalingam Saravanan Leelavinothan Pari. Articles Volume 31 Issue 5 December 2006 pp 581- ...

  9. Evaluation of the levels of phthalate ester plasticizers in surface ...

    African Journals Online (AJOL)

    The objective of this study was to determine the level of phthalate ester plasticizers in Ethiope River water samples. Gas chromatography (GC) coupled with mass spectrometer (MS) was used to evaluate the levels of dimethyl phthalate (DMP), diethyl phthalate (DEP), dibuthyl phthalate (DBP), diethylhexyl phthalate (DEHP), ...

  10. FEL induced molecular operation on cultured fibroblast and cholesterol ester

    International Nuclear Information System (INIS)

    Awazu, Kunio; Ogino, Seiji; Nishimura, Eiichi; Tomimasu, Takio; Yasumoto, Masato.

    1997-01-01

    Free Electron Lasers can be used to molecular operation such as the delivery of a number of molecules into cells or the separation of cholesterol ester. First, cultured NIH3T3 cells are exposed to high-intensity short pulse Free Electron Laser (FEL). The FEL is tuned to an absorption maximum wavelength, 6.1 μm, which was measured by microscopic FTIR. A fluorescence dye in the cell suspension is more absorbed into the cell with the FEL exposure due to the FEL-induced mechanical stress to the cell membrane. A quantitative fluorescence microscopy is used to determine the efficiency of delivery. Second, as a compound in a lipid cell, cholesterol ester was exposed to 5.75 μm FEL. FTIR measurement was done to evaluate the modification of the cholesterol ester. The result showed that the fluorescence intensity of sample cells were higher than that of control cells, and there was significant difference between the control and the sample group. Blebbing and the colony formation of the cells were observed for cells with mechanical stress. As for the cholesterol ester, it can be modified by the FEL irradiation. These results showed that FEL can be used as a molecular operational tool by photo-chemical and photo-mechanical interaction. (author)

  11. Preparation of Jojoba Oil Ester Derivatives for Biodiesel Evaluation

    Science.gov (United States)

    As a result of the increase in commodity vegetable oil prices, it is imperative that non-food oils should be considered as alternative feedstocks for biodiesel production. Jojoba oil is unusual in that it is comprised of wax esters as opposed to the triglycerides found in typical vegetable oils. A...

  12. Metronidazole citrate ester as the new prodrug of metronidazole

    Directory of Open Access Journals (Sweden)

    Elżbieta Dąbrowska-Maś

    2017-07-01

    Full Text Available Many attempts have been made since 1960th to obtain ester prodrugs of metronidazole active moiety to be used for parenteral forms, with the same action against microorganisms. Until now there is not any ester prodrug marketed for this route of administration. The synthesis from metronidazole and citric acid of new ester prodrug of metronidazole with citric acid in a form of disodium salt and the way of purification were described. The structure of sodium metronidazole citrate was elucidated with IR, MS, 1H NMR and 13C NMR spectra. Also impurities present in this ester were identified using 1H NMR technique. Additionally, the solubility in water was measured as well as pH of 10% (w/w aqueous solution, and both values indicated that there is a possibility to obtain concentrated solutions for injection of neutral pH, even without need of buffering. Finally, the Ames assay using six tester strains S. typhimurium TA98, TA100, TA1535, TA1537 and E. coli uvrA, [pKM101] shown weak genotoxic potential, comparable with metronidazole.

  13. Phthalate ester plasticizers in freshwater systems of Venda, South ...

    African Journals Online (AJOL)

    Phthalate ester plasticizers were determined in rivers and dams of the Venda region, South Africa. Liquid-liquid extraction, column chromatographic clean-up and capillary gas chromatography were the methods used for the quantitative analyses. Levels of phthalates in water samples from the rivers and dams ranged from ...

  14. Biocatalytic synthesis and antioxidant capacities of ascorbyl esters ...

    African Journals Online (AJOL)

    Novozym 435 was used to catalyze the synthesis of fatty acid (FA) ascorbyl esters in tert-butanol using methyl palmitate, oleic and linoleic acids, and soybean oil as acyl donors. Response surface methodology (RSM) and three-level-four-factor central composite rotatable design (CCRD) were employed to optimize the ...

  15. Physical proprieties of low viscosity estolide 2-ethylhexyl esters

    Science.gov (United States)

    Acetic- and butyric-capped oleic estolide 2-ethylhexyl (2-EH) esters were synthesized in a perchloric acid catalyzed (0.05 equiv) one-pot process from industrial 90% oleic acid and either acetic or butyric fatty acids at two different ratios. This was directly followed by the esterification process ...

  16. Presidendiauto jalakäijate teel / Ester Shank

    Index Scriptorium Estoniae

    Šank, Ester, 1956-

    2003-01-01

    Presidendi pressinõunik Ester Shank selgitab, miks president Arnold Rüütel sõitis eskorauto saatel lauluväljakule Andrea Bocelli ja Annely Peebo kontserdile läbi Kadrioru pargi jalakäijate teed mööda

  17. Analysis of phthalate esters contamination in drinking water samples ...

    African Journals Online (AJOL)

    The optimum condition method was successfully applied to the analysis of phthalate esters contamination in bottled drinking water samples. The concentration of DMP, DEP and DBP in drinking water samples were below allowable levels, while the DEHP concentration in three samples was found to be greater than the ...

  18. RAFT Polymerization of Vinyl Esters: Synthesis and Applications

    Directory of Open Access Journals (Sweden)

    Simon Harrisson

    2014-05-01

    Full Text Available This article is the first comprehensive review on the study and use of vinyl ester monomers in reversible addition fragmentation chain transfer (RAFT polymerization. It covers all the synthetic aspects associated with the definition of precision polymers comprising poly(vinyl ester building blocks, such as the choice of RAFT agent and reaction conditions in order to progress from simple to complex macromolecular architectures. Although vinyl acetate was by far the most studied monomer of the range, many vinyl esters have been considered in order to tune various polymer properties, in particular, solubility in supercritical carbon dioxide (scCO2. A special emphasis is given to novel poly(vinyl alkylates with enhanced solubilities in scCO2, with applications as reactive stabilizers for dispersion polymerization and macromolecular surfactants for CO2 media. Other miscellaneous uses of poly(vinyl esters synthesized by RAFT, for instance as a means to produce poly(vinyl alcohol with controlled characteristics for use in the biomedical area, are also covered.

  19. Synthesis of fatty acid starch esters in supercritical carbon dioxide

    NARCIS (Netherlands)

    Muljana, Henky; van der Knoop, Sjoerd; Keijzer, Danielle; Picchioni, Francesco; Janssen, Leon P. B. M.; Heeres, Hero J.

    2010-01-01

    This manuscript describes an exploratory study on the synthesis of fatty acid/potato starch esters using supercritical carbon dioxide (scCO(2)) as the solvent. The effects of process variables such as pressure (6-25 MPa), temperature (120-150 degrees C) and various basic catalysts and fatty acid

  20. Selective synthesis of thiodiglycol dicarboxylic acid esters via p ...

    Indian Academy of Sciences (India)

    The esterification of thiodiglycol and long alkyl-chain carboxylic acids is reported. Reaction of thiodiglycol with carboxylic acid via -TsOH/C-catalysed direct esterification afforded thiodiglycol dicarboxylic acid esters in good yields and chemoselectivity. The use of immobilized -TsOH on activated carbon as catalyst is ...

  1. A Convenient Synthesis of Amino Acid Methyl Esters

    Directory of Open Access Journals (Sweden)

    Yaowu Sha

    2008-05-01

    Full Text Available A series of amino acid methyl ester hydrochlorides were prepared in good toexcellent yields by the room temperature reaction of amino acids with methanol in thepresence of trimethylchlorosilane. This method is not only compatible with natural aminoacids, but also with other aromatic and aliphatic amino acids.

  2. Carboxylic ester hydrolases in mitochondria from rat skeletal muscle

    DEFF Research Database (Denmark)

    Kirkeby, S; Moe, D; Zelander, T

    1990-01-01

    A mitochondrial pellet, prepared from rat skeletal muscle, contained a number of carboxylic ester hydrolase isoenzymes. The esterases which split alpha-naphthyl acetate were organophosphate sensitive, whereas two out of three indoxyl acetate hydrolysing enzymes were resistant to both organophosph...

  3. Polyfluorinated alkyl phosphate ester surfactants - current knowledge and knowledge gaps

    DEFF Research Database (Denmark)

    Taxvig, Camilla; Rosenmai, Anna Kjerstine; Vinggaard, Anne Marie

    2014-01-01

    information on fluorochemicals. Polyfluorinated alkyl phosphate ester surfactants (PAPs) belong to the group of polyfluorinated alkyl surfactants. They have been detected in indoor dust and are widely used in food-contact materials, from which they have the ability to migrate into food. Toxicological data...

  4. Structure and Reactivity of the Cysteine Methyl Ester Radical Cation

    NARCIS (Netherlands)

    Osburn, S.; Steill, J. D.; Oomens, J.; O' Hair, R. A. J.; Van Stipdonk, M.; Ryzhov, V.

    2011-01-01

    The structure and reactivity of the cysteine methyl ester radical cation, CysOMe(center dot+), have been examined in the gas phase using a combination of experiment and density functional theory (DFT) calculations. CysOMe(center dot+) undergoes rapid ion molecule reactions with dimethyl disulfide,

  5. Enantioselective Reduction of Prochiral Ketones using Spiroborate Esters as Catalysts

    Science.gov (United States)

    Stepanenko, Viatcheslav; De Jesus, Melvin; Correa, Wildeliz; Guzman, Irisbel; Vazquez, Cindybeth; de la Cruz, Wilanet; Ortiz-Marciales, Margarita; Barnes, Charles L.

    2009-01-01

    Novel spiroborate esters derived nonracemic 1,2-aminoalcohols and ethylene glycol are reported as highly effective catalysts for the asymmetric borane reduction of a variety of prochiral ketones with borane-dimethyl sulfide complex at room temperature. Optically active alcohols were obtained in excellent chemical yields using 0.1 to 10 mol % of catalysts with up to 99% ee. PMID:19554205

  6. Ranking of aquatic toxicity of esters modelled by QSAR.

    Science.gov (United States)

    Papa, Ester; Battaini, Francesca; Gramatica, Paola

    2005-02-01

    Alternative methods like predictions based on Quantitative Structure-Activity Relationships (QSARs) are now accepted to fill data gaps and define priority lists for more expensive and time consuming assessments. A heterogeneous data set of 74 esters was studied for their aquatic toxicity, and available experimental toxicity data on algae, Daphnia and fish were used to develop statistically validated QSAR models, obtained using multiple linear regression (MLR) by the OLS (Ordinary Least Squares) method and GA-VSS (Variable Subset Selection by Genetic Algorithms) to predict missing values. An ESter Aquatic Toxicity INdex (ESATIN) was then obtained by combining, by PCA, experimental and predicted toxicity data, from which model outliers and esters highly influential due to their structure had been eliminated. Finally this integrated aquatic toxicity index, defined by the PC1 score, was modelled using only a few theoretical molecular descriptors. This last QSAR model, statistically validated for its predictive power, could be proposed as a preliminary evaluative method for screening/prioritising esters according to their integrated aquatic toxicity, just starting from their molecular structure.

  7. Controlled grafting of cellulose esters using SET-LRP process

    Czech Academy of Sciences Publication Activity Database

    Vlček, Petr; Raus, Vladimír; Janata, Miroslav; Kříž, Jaroslav; Sikora, Antonín

    2011-01-01

    Roč. 49, č. 1 (2011), s. 164-173 ISSN 0887-624X R&D Projects: GA ČR GA106/09/1348 Institutional research plan: CEZ:AV0Z40500505 Keywords : cellulose esters * copolymerization * graft copolymers Subject RIV: JI - Composite Materials Impact factor: 3.919, year: 2011

  8. Selective synthesis of thiodiglycol dicarboxylic acid esters via p ...

    Indian Academy of Sciences (India)

    highly valuable from both environmental and economi- cal points of view. This illustrates the potential utility of the methodology for the construction of various long alkyl-chain esters of thiodiglycol. References. 1. (a) Pollack M A and Penville N J 1948 US patent,. 2454568. (b) Boussely J, Chandavoine M, Chignac M et al.

  9. Enol esters: versatile substrates for Mannich-type multicomponent reactions.

    Science.gov (United States)

    Isambert, Nicolas; Cruz, Montse; Arévalo, María José; Gómez, Elena; Lavilla, Rodolfo

    2007-10-11

    The interaction of cyclic enol esters with diversely substituted anilines and ethyl glyoxalate yields, under Sc(OTf)3 catalysis, disubstituted N-aryl lactams in a multicomponent reaction. The protocol allows access to the trans stereoisomers after an epimerization of the initial mixture in which the cis isomers predominate. Vinyl acetate yields quinoline derivatives, whereas isopropenyl acetate leads to the corresponding Mannich adducts.

  10. Caffeic Acid Phenethyl Ester (CAPE) mediated decrease in ...

    African Journals Online (AJOL)

    Background: Caffeic acid phenethyl ester (CAPE) is a phytochemically active component obtained from honeybee hive propolis. CAPE has been reported to show antimitogenic, anticancer, and other beneficial medicinal properties. Many of its activities have been reported to be mediated by inhibiting levels of matrix ...

  11. Diorganotin(IV) Complexes with Methionine Methyl Ester. Equilibria ...

    African Journals Online (AJOL)

    IV) (DBT) and diphenyltin(IV) (DPT) was investigated at 25 °C and 0.1 mol dm–3 ionic strength in water for dimethyltin(IV) and in 50 % dioxane–water mixture for dibutyltin(IV) and diphenyltin(IV). Methionine methyl ester forms1:1 and 1:2 ...

  12. Diorganotin(IV) Complexes with Methionine Methyl Ester. Equilibria ...

    African Journals Online (AJOL)

    NICO

    Diorganotin(IV) Complexes with Methionine Methyl Ester. Equilibria and Displacement by DNA Constituents. M.M. Shoukry1,2,* Ayser Al-Alousi2 and Sameya M. Tarek. 1Deparment of Chemistry, Faculty of Science, Islamic University, Madina, Saudi Arabia. 2Department of Chemistry, Faculty of Science, Cairo University, ...

  13. Iodine-Catalyzed Synthesis of Mixed Cellulose Esters

    Science.gov (United States)

    A novel method for the preparation of cellulose mixed acetate is described herein, involving the concurrent use of iodine and mixed anhydride. The method is simple, rapid, efficient, and solvent-less. With this method, cellulose mixed esters has been synthesized. ...

  14. Encapsulating fatty acid esters of bioactive compounds in starch

    Science.gov (United States)

    Lay Ma, Ursula Vanesa

    Interest in the use of many bioactive compounds in foods is growing in large part because of the apparent health benefits of these molecules. However, many of these compounds can be easily degraded during processing, storage, or their passage through the gastrointestinal tract before reaching the target site. In addition, they can be bitter, acrid, or astringent, which may negatively affect the sensory properties of the product. Encapsulation of these molecules may increase their stability during processing, storage, and in the gastrointestinal tract, while providing controlled release properties. The ability of amylose to form inclusion complexes and spherulites while entrapping certain compounds has been suggested as a potential method for encapsulation of certain molecules. However, complex formation and spherulitic crystallization are greatly affected by the type of inclusion molecules, type of starch, and processing conditions. The objectives of the present investigation were to: (a) study the effect of amylose, amylopectin, and intermediate material on spherulite formation and its microstructure; (b) investigate the formation of amylose and high amylose starch inclusion complexes with ascorbyl palmitate, retinyl palmitate, and phytosterol esters; (c) evaluate the ability of spherulites to form in the presence of fatty acid esters and to entrap ascorbyl palmitate, retinyl palmitate, and phytosterol esters; and (d) evaluate the effect of processing conditions on spherulite formation and fatty acid ester entrapment. Higher ratios of linear to branched molecules resulted in the formation of more and rounder spherulites with higher heat stability. In addition to the presence of branches, it appears that spherulitic crystallization is also affected by other factors, such as degree of branching, chain length, and chain length distribution. Amylose and Hylon VII starch formed inclusion complexes with fatty acid esters of ascorbic acid, retinol, or phytosterols

  15. Characteristics of floc formation of anion and cation exchange resin in precoat filter using powdered ion exchange resin

    International Nuclear Information System (INIS)

    Adachi, Tetsurou; Sawa, Toshio; Shindoh, Toshikazu.

    1989-01-01

    The filtration performance of mixed filter aid consisting of powdered anion and cation exchange resins used in the precoat filter is closely related to the characteristics of floc formation. The physical, chemical and electrochemical properties of powdered ion exchange resin were measured and the factors related to floc formation of anion and cation exchange resin were investigated by measuring the specific settle volume of resin floc as an evaluating index. It was found that these factors were mixing ratio, nature of resins and particle size of resins. In addition, it was assumed on the bases of these results that the amount of resin floc was related to sum of the surface electric charges of both resins. The filling ratio of resin floc was related to their product by multiplication and an experimental expression was obtained. The specific settle volume of resin floc could then be simulated by particle size, surface area, ion exchange capacity and degree of ionization of the powdered ion exchange resin. (author)

  16. Characteristics of floc formation of anion and cation exchange resin in precoat filter using powdered ion exchange resin

    Energy Technology Data Exchange (ETDEWEB)

    Adachi, Tetsurou (Nitto Denko Corp., Ibaraki, Osaka (Japan)); Sawa, Toshio; Shindoh, Toshikazu

    1989-09-01

    The filtration performance of mixed filter aid consisting of powdered anion and cation exchange resins used in the precoat filter is closely related to the characteristics of floc formation. The physical, chemical and electrochemical properties of powdered ion exchange resin were measured and the factors related to floc formation of anion and cation exchange resin were investigated by measuring the specific settle volume of resin floc as an evaluating index. It was found that these factors were mixing ratio, nature of resins and particle size of resins. In addition, it was assumed on the bases of these results that the amount of resin floc was related to sum of the surface electric charges of both resins. The filling ratio of resin floc was related to their product by multiplication and an experimental expression was obtained. The specific settle volume of resin floc could then be simulated by particle size, surface area, ion exchange capacity and degree of ionization of the powdered ion exchange resin. (author).

  17. Two-generation reproductive toxicity study of plant stanol esters in rats

    NARCIS (Netherlands)

    Whittaker, M.H.; Frankos, V.H.; Wolterbeek, A.P.M.; Waalkens-Berendsen, D.H.

    1999-01-01

    Plant stanol esters are intended for use as an ingredient in food to reduce the absorption of cholesterol from the gastrointestinal tract. Consumption of plant stanol esters has a demonstrated diet-derived public health benefit, as shown by numerous clinical studies. Plant stanol esters are

  18. 21 CFR 178.3600 - Methyl glucoside-coconut oil ester.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methyl glucoside-coconut oil ester. 178.3600... SANITIZERS Certain Adjuvants and Production Aids § 178.3600 Methyl glucoside-coconut oil ester. Methyl glucoside-coconut oil ester identified in § 172.816(a) of this chapter may be safely used as a processing...

  19. 21 CFR 172.816 - Methyl glucoside-coconut oil ester.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methyl glucoside-coconut oil ester. 172.816 Section... HUMAN CONSUMPTION Multipurpose Additives § 172.816 Methyl glucoside-coconut oil ester. Methyl glucoside-coconut oil ester may be safely used in food in accordance with the following conditions: (a) It is the...

  20. 21 CFR 573.640 - Methyl esters of higher fatty acids.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Methyl esters of higher fatty acids. 573.640... ANIMALS Food Additive Listing § 573.640 Methyl esters of higher fatty acids. The food additive methyl esters of higher fatty acids may be safely used in animal feeds in accordance with the following...

  1. Variability of some diterpene esters in coffee beverages as influenced by brewing procedures.

    Science.gov (United States)

    Moeenfard, Marzieh; Erny, Guillaume L; Alves, Arminda

    2016-11-01

    Several coffee brews, including classical and commercial beverages, were analyzed for their diterpene esters content (cafestol and kahweol linoleate, oleate, palmitate and stearate) by high performance liquid chromatography with diode array detector (HPLC-DAD) combined with spectral deconvolution. Due to the coelution of cafestol and kahweol esters at 225 nm, HPLC-DAD did not give accurate quantification of cafestol esters. Accordingly, spectral deconvolution was used to deconvolve the co-migrating profiles. Total cafestol and kahweol esters content of classical coffee brews ranged from 5-232 to 2-1016 mg/L, respectively. Commercial blends contained 1-54 mg/L of total cafestol esters and 2-403 mg/L of total kahweol esters. Boiled coffee had the highest diterpene esters content, while filtered and instant brews showed the lowest concentrations. However, individual diterpene esters content was not affected by brewing procedure as in terms of kahweol esters, kahweol palmitate was the main compound in all samples, followed by kahweol linoleate, oleate and stearate. Higher amounts of cafestol palmitate and stearate were also observed compared to cafestol linoleate and cafestol oleate. The ratio of diterpene esters esterified with unsaturated fatty acids to total diterpene esters was considered as measure of their unsaturation in analyzed samples which varied from 47 to 52%. Providing new information regarding the diterpene esters content and their distribution in coffee brews will allow a better use of coffee as a functional beverage.

  2. 40 CFR 721.8340 - Mono esters from 2- propenoic acid (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Mono esters from 2- propenoic acid... Specific Chemical Substances § 721.8340 Mono esters from 2- propenoic acid (generic). (a) Chemical... as mono esters from 2-propenoic acid (PMN P-01-85) is subject to reporting under this section for the...

  3. 21 CFR 184.1101 - Diacetyl tartaric acid esters of mono- and diglycerides.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Diacetyl tartaric acid esters of mono- and... acid esters of mono- and diglycerides. (a) Diacetyl tartaric acid esters of mono- and diglycerides... prepared by the reaction of diacetyl tartaric anhydride with mono- and diglycerides that are derived from...

  4. Post-irradiation hardness of resin-modified glass ionomer cements and a polyacid-modified composite resin

    International Nuclear Information System (INIS)

    Yap, A.U.J.

    1997-01-01

    This study examined the post-irradiation hardness of resin-modified glass ionomer cements and a polyacid-modified composite resin using a digital microhardness tester. Change in hardness of these materials over a period of 6 months was compared to that of conventional glass ionomer cements and a composite resin. With the exception of the composite resin, all materials showed a significant increase in hardness over 24 h after their initial set. Dual-cure resin-modified glass ionomer cements showed decreased hardness with increased storage time in saline at 37 o C. Results suggest that the addition of resins to glass ionomer cements does not improve initial hardness and does not negate the acid-base reaction of conventional cements. Resin addition may, however, lead to increased water sorption and decreased hardness. (author)

  5. Synthesis of thermoplastic poly(ester-olefin elastomers

    Directory of Open Access Journals (Sweden)

    Tanasijević Branka

    2004-01-01

    Full Text Available A series of thermoplastic poly(ester-olefin elastomers, based on poly(ethylene-stat-butylene, HO-PEB-OH, as the soft segment and poly (butylene terephthalate, PBT, as the hard segment, were synthesized by a catalyzed transesterification reaction in solution. The incorporation of soft hydrogenated poly(butadiene segments into the copolyester backbone was accomplished by the polycondensation of α, ω-dihydroxyl telechelic HO-PEB-OH, (PEB Mn = 3092 g/mol with 1,4-butanediol (BD and dimethyl terephthalate (DMT in the presence of a 50 wt-% high boiling solvent i.e., 1,2,4-trichlorobenzene. The molar ratio of the starting comonomers was selected to result in a constant hard to soft weight ratio of 60:40. The synthesis was optimized in terms of both the concentration of catalyst, tetra-n-butyl-titanate (Ti(OBu4, and stabilizer, N,N'-diphenyl-p-phenylenediamine (DPPD, as well as the reaction time. It was found that the optimal catalyst concentration (Ti(OBu4 for the synthesis of these thermoplastic elastomers was 1.0 mmol/mol ester and the optimal DPPD concentration was 1.0 wt-%. The extent of the reaction was followed by measuring the inherent viscosity of the reaction mixture. The effectiveness of the incorporation of the soft segments into the copolymer chains was proved by Soxhlet extraction with chloroform. The molecular structures, composition and the size of the synthesized poly(ester-butylenes were verified by 1H NMR spectroscopy, viscometry of dilute solutions and the complex dynamic melt viscosity. The thermal properties of poly(ester-olefins were investigated by differential scanning calorimetry (DSC. The degree of crystallinity was also determined by DSC. The thermal and thermo-oxidative stability were investigated by thermogravimetric analysis (TGA. The rheological properties of poly(ester-olefins were investigated by dynamic mechanical spectroscopy in the melt and solid state.

  6. Nanomechanical properties of dental resin-composites.

    Science.gov (United States)

    El-Safty, S; Akhtar, R; Silikas, N; Watts, D C

    2012-12-01

    To determine by nanoindentation the hardness and elastic modulus of resin-composites, including a series with systematically varied filler loading, plus other representative materials that fall into the categories of flowable, bulk-fill and conventional nano-hybrid types. Ten dental resin-composites: three flowable, three bulk-fill and four conventional were investigated using nanoindentation. Disc specimens (15mm×2mm) were prepared from each material using a metallic mold. Specimens were irradiated in the mold at top and bottom surfaces in multiple overlapping points (40s each) with light curing unit at 650mW/cm(2). Specimens were then mounted in 3cm diameter phenolic ring forms and embedded in a self-curing polystyrene resin. After grinding and polishing, specimens were stored in distilled water at 37°C for 7 days. Specimens were investigated using an Agilent Technologies XP nanoindenter equipped with a Berkovich diamond tip (100nm radius). Each specimen was loaded at one loading rate and three different unloading rates (at room temperature) with thirty indentations, per unloading rate. The maximum load applied by the nanoindenter to examine the specimens was 10mN. Dependent on the type of the resin-composite material, the mean values ranged from 0.73GPa to 1.60GPa for nanohardness and from 14.44GPa to 24.07GPa for elastic modulus. There was a significant positive non-linear correlation between elastic modulus and nanohardness (r(2)=0.88). Nonlinear regression revealed a significant positive correlation (r(2)=0.62) between elastic moduli and filler loading and a non-significant correlation (r(2)=0.50) between nanohardness and filler loading of the studied materials. Varying the unloading rates showed no consistent effect on the elastic modulus and nanohardness of the studied materials. For a specific resin matrix, both elastic moduli and nanohardness correlated positively with filler loading. For the resin-composites investigated, the group-average elastic

  7. Valimiskaotuse haavu raviva Rahvaliidu ajutine juht Ester Tuiksoo : "Meil on tugev küünarnukitunne" / Ester Tuiksoo

    Index Scriptorium Estoniae

    Tuiksoo, Ester, 1965-

    2007-01-01

    Ilmunud ka: Severnoje Poberezhje, 28. märts 2007, lk. 2. Delfi lugejate küsimustele vastab Rahvaliidu ajutine juht ja lahkuva valitsuse põllumajandusminister Ester Tuiksoo, kellelt päriti nii erakonna maine taastamise, eesti toidu kui ka jopede jagamise kohta

  8. Contact allergy to epoxy resin: risk occupations and consequences.

    Science.gov (United States)

    Bangsgaard, Nannie; Thyssen, Jacob Pontoppidan; Menné, Torkil; Andersen, Klaus Ejner; Mortz, Charlotte G; Paulsen, Evy; Sommerlund, Mette; Veien, Niels Kren; Laurberg, Grete; Kaaber, Knud; Thormann, Jens; Andersen, Bo Lasthein; Danielsen, Anne; Avnstorp, Christian; Kristensen, Berit; Kristensen, Ove; Vissing, Susanne; Nielsen, Niels Henrik; Johansen, Jeanne Duus

    2012-08-01

    Epoxy resin monomers are strong skin sensitizers that are widely used in industrial sectors. In Denmark, the law stipulates that workers must undergo a course on safe handling of epoxy resins prior to occupational exposure, but the effectiveness of this initiative is largely unknown. To evaluate the prevalence of contact allergy to epoxy resin monomer (diglycidyl ether of bisphenol A; MW 340) among patients with suspected contact dermatitis and relate this to occupation and work-related consequences. The dataset comprised 20 808 consecutive dermatitis patients patch tested during 2005-2009. All patients with an epoxy resin-positive patch test were sent a questionnaire. A positive patch test reaction to epoxy resin was found in 275 patients (1.3%), with a higher proportion in men (1.9%) than in women (1.0%). The prevalence of sensitization to epoxy resin remained stable over the study period. Of the patients with an epoxy resin-positive patch test, 71% returned a questionnaire; 95 patients had worked with epoxy resin in the occupational setting, and, of these, one-third did not use protective gloves and only 50.5% (48) had participated in an educational programme. The 1% prevalence of epoxy resin contact allergy is equivalent to reports from other countries. The high occurrence of epoxy resin exposure at work, and the limited use of protective measures, indicate that reinforcement of the law is required. © 2012 John Wiley & Sons A/S.

  9. Handling sticky resin by stingless bees (Hymenoptera, Apidae

    Directory of Open Access Journals (Sweden)

    Markus Gastauer

    2011-06-01

    Full Text Available For their nest defense, stingless bees (Meliponini collect plant resins which they stick on intruders like ants or cleptobiotic robber bees causing their immobilization. The aim of this article is to identify all parts of stingless bee workers contacting these sticky resins. Of special interest are those body parts with anti-adhesive properties to resin, where it can be removed without residues. For that, extensive behavioral observations during foraging flight, handling and application of the resin have been carried out. When handling the resin, all tarsi touch the resin while walking above it. For transportation from plants to the nest during foraging flight, the resin is packed to the corbicula via tarsi and basitarsi of front and middle legs. Once stuck to the resin or after the corbicula had been unloaded, the bee's legs have to be cleaned thoroughly. Only the tips of the mandibles, that form, cut and apply the sticky resin, seem to have at least temporarily resin-rejecting properties.

  10. Petroleum Resins: Separation, Character, and Role in Petroleum

    DEFF Research Database (Denmark)

    Andersen, Simon Ivar; Speight, James

    2001-01-01

    In petroleum science, the term resin generally implies material that has been eluted from various solid adsorbents, whereas the term maltenes (or petrolenes) indicates a mixture of the resins and oils obtained as filtrates from the asphaltene precipitation. Thus, after the asphaltenes are precipi......In petroleum science, the term resin generally implies material that has been eluted from various solid adsorbents, whereas the term maltenes (or petrolenes) indicates a mixture of the resins and oils obtained as filtrates from the asphaltene precipitation. Thus, after the asphaltenes...... are precipitated, adsorbents are added to the n-pentane solutions of the resins and oils, by which process the resins are adsorbed and subsequently recovered by the use of a more polar solvent, and the oils remain in solution. The resin fraction plays an important role in the stability of petroleum and prevents...... of the fact that the resin fraction is extremely important to the stability of petroleum, there is surprisingly little work reported on the characteristics of the resins. This article summarizes the work that has been carried out in determining the character and properties of the resin constituents...

  11. Anion-exchange resin-based desulfurization process. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Sheth, A C; Dharmapurikar, R; Strevel, S D

    1994-01-01

    The following investigations were performed: (1) batch mode screening of eleven(11) commercially available resins and selection of three candidate resins for further evaluation in a fixed-bed setup. (2) Process variables study using three candidate resins in the fixed-bed setup and selection of the ``best`` resin for process economics development. (3) Exhaustion efficiency and solution concentration were found to be inversely related necessitating a trade-off between the resin cost versus the cost of evaporation/concentration of ensuing effluents. (4) Higher concentration of the HCO{sub 3}{sup {minus}} form of active sites over less active CO{sub 3}{sup 2{minus}} form of sites in the resin was believed to be the main reason for the observed increase in the equilibrium capacity of the resin at an elevated static CO{sub 2}-pressure. This Increase in capacity was found to level off around 80--120 psig range. The increase in CO{sub 2}-pressure, however, did not appear to affect the overall ion-exchange kinetics. (5) In the fixed-bed mode, the solution concentration was found to affect the equilibrium capacity of candidate resins. Their relationship was well satisfied by the Langmuir type non-linear equilibrium isotherm. Alternatively, the effect of solution concentration on overall ion-exchange kinetics varied from resin to resin. (6) Product inhibition effect on the resin was observed as an initial increase followed by a significant decrease in the resin`s equilibrium capacity for SO{sub 4}{sup 2{minus}} as the HCO{sub 3}{sup {minus}}/SO{sub 4}{sup 2{minus}} molar ratio in the solution was increased from 0 to 1.0. This ratio, however, did not affect the overall ion-exchange kinetics.

  12. Sequestration Resins for Accelerating Removal of Radioactive Contaminants

    International Nuclear Information System (INIS)

    Frattini, Paul-L.; Wells, Daniel-M.; Garcia, Susan-E.; Richard, Kohlmann; Asay, Roger; Yengoyan, Leon

    2012-09-01

    The Electric Power Research Institute (EPRI) is developing sequestration resins that can be used in the treatment of nuclear plant water streams for the enhanced removal of ionic cobalt. EPRI is focusing on three key areas of success: 1. Plant safety. The resins that are synthesized must be fully tested to determine that no leachable species or decomposition products (in the event of a resin bed failure) would be introduced to the plant. 2. Acceptable system performance. The resins are currently being synthesized in a powdered form for use in the reactor water clean-up and fuel pool clean-up systems that utilize pre-coatable filter elements. The resins must have effective flocking behavior; uniform application over the underlay resin and efficient removal from the septa elements after use. Bead type resins are also under development. 3. Enhanced cobalt removal. The resins are expected to out-perform the currently used ion exchange resins in the removal of ionic cobalt. During nuclear plant maintenance or refueling outages, current ion exchange resins may require several days to reduce concentrations of cobalt (for example, radio-cobalt 60 Co and 58 Co) and other activated corrosion products to safe levels in reactor coolant streams. This performance limitation often delays key maintenance activities. EPRI's resins are expected to provide at least a three-fold increase in removal capacity in light water reactor coolants. These resins also offer the potential for higher overall removal efficiencies reducing occupational exposures and waste management costs. This paper addresses issues from the range of novel resin development for radio-cobalt removal from synthesis at the bench-top level through scale-up to demonstration of use in an actual operating nuclear power plant. (authors)

  13. Curing kinetics of alkyd/melamine resin mixtures

    Directory of Open Access Journals (Sweden)

    Jovičić Mirjana C.

    2009-01-01

    Full Text Available Alkyd resins are the most popular and useful synthetic resins applied as the binder in protective coatings. Frequently they are not used alone but are modified with other synthetic resins in the manufacture of the coatings. An alkyd/melamine resin mixture is the usual composition for the preparation of coating called 'baking enamel' and it is cured through functional groups of resins at high temperatures. In this paper, curing kinetics of alkyd resins based on castor oil and dehydrated castor oil with melamine resin, has been studied by DSC method with programmed heating and in isothermal mode. The results determined from dynamic DSC curves were mathematically transformed using the Ozawa isoconversional method for obtaining the isothermal data. These results, degree of curing versus time, are in good agreement with those determined by the isothermal DSC experiments. By applying the Ozawa method it is possible to calculate the isothermal kinetic parameters for the alkyd/melamine resin mixtures curing using only calorimetric data obtained by dynamic DSC runs. Depending on the alkyd resin type and ratio in mixtures the values of activation energies of curing process of resin mixtures are from 51.3 to 114 kJ mol-1. The rate constant of curing increases with increasing the content of melamine resin in the mixture and with curing temperature. The reaction order varies from 1.12 to 1.37 for alkyd based on dehydrated castor oil/melamine resin mixtures and from 1.74 to 2.03 for mixtures with alkyd based on castor oil. Based on the results obtained, we propose that dehydrated castor oil alkyd/melamine resin mixtures can be used in practice (curing temperatures from 120 to 160°C.

  14. Mechanistic understanding of fouling of protein A chromatography resin.

    Science.gov (United States)

    Pathak, Mili; Rathore, Anurag S

    2016-08-12

    This paper aims to provide a thorough understanding of how fouling of Protein A resin takes place. Binding and mass transport properties of widely used agarose-based Protein A resin, MabSelect SuRe™, have been examined to understand the mechanism of resin fouling. There could be various factors that impact resin fouling. These include product/impurity build-up due to components in the feed material and ligand degradation due to the use of harsh buffers. To unravel their contributions, cycling studies were performed with and without product loading. The results presented in this paper provide a lucid understanding of the causative factors that limit Protein A chromatographic resin lifetime. The capacity fall for protein A resin at the end of 100th cycle due to use of feed material was found to be five times greater than that without using feed material. Compared to the fresh resin, the cycled resin samples shows 24% reduction in particle porosity and 51% reduction in pore mass transfer coefficient. Transmission electron microscopy (TEM) was used to qualitatively monitor accumulation of foulants on the cycled resin. Fouled resin sample contained a dense residue in the interior and exterior of resin particle both as a film at the bead surface and as granules. The surface activation energy increased five times in the case of fouled resin sample. The major event in fouling was identified as the non-specific adsorption of the feed material components on resin, signaling that pore diffusion is the rate limiting step. It is anticipated that these findings will assist in development of a more robust and economical downstream manufacturing process for monoclonal antibody purification. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. Epoxy resins used to seal brachytherapy seed

    International Nuclear Information System (INIS)

    Ferreira, Natalia Carolina Camargos; Ferraz, Wilmar Barbosa; Reis, Sergio Carneiro dos; Santos, Ana Maria Matildes dos

    2013-01-01

    Prostate cancer treatment with brachytherapy is recommended for patients with cancer at an early stage. In this treatment, small radioactive seeds are implanted directly in the prostate gland. These seeds are composed at least of one radionuclide carrier and an X-ray marker enclosed within a metallic tube usually sealed by laser process. This process is expensive and, furthermore, it can provoke a partial volatilization of the radionuclide and change the isotropy in dose distribution around the seed. In this paper, we present a new sealing process using epoxy resin. Three kinds of resins were utilized and characterized by scanning electron microscopy (SEM), energy dispersive X ray (EDS) and by differential scanning calorimetry (DSC) after immersion in simulated body fluid (SBF) and in sodium iodine solution (NaI). The sealing process showed excellent potential to replace the sealing laser usually employed. (author)

  16. Flammability of Epoxy Resins Containing Phosphorus

    Science.gov (United States)

    Hergenrother, P. M.; Thompson, C. M.; Smith, J. G.; Connell, J. W.; Hinkley, J. A.

    2005-01-01

    As part of a program to develop fire-resistant exterior composite structures for future subsonic commercial and general aviation aircraft, flame-retardant epoxy resins are under investigation. Epoxies and their curing agents (aromatic diamines) containing phosphorus were synthesized and used to prepare epoxy formulations. Phosphorus was incorporated within the backbone of the epoxy resin and not used as an additive. The resulting cured neat epoxy formulations were characterized by thermogravimetric analysis, propane torch test, elemental analysis, microscale combustion calorimetry, and fire calorimetry. Several formulations showed excellent flame retardation with phosphorous contents as low as 1.5% by weight. The fracture toughness and compressive strength of several cured formulations showed no detrimental effect due to phosphorus content. The chemistry and properties of these new epoxy formulations are discussed.

  17. Epoxy resins in the construction industry.

    Science.gov (United States)

    Spee, Ton; Van Duivenbooden, Cor; Terwoert, Jeroen

    2006-09-01

    Epoxy resins are used as coatings, adhesives, and in wood and concrete repair. However, epoxy resins can be highly irritating to the skin and are strong sensitizers. Some hardeners are carcinogenic. Based on the results of earlier Dutch studies, an international project on "best practices,"--Epoxy Code--with epoxy products was started. Partners were from Denmark, Germany, the Netherlands, and the UK. The "Code" deals with substitution, safe working procedures, safer tools, and skin protection. The feasibility of an internationally agreed "ranking system" for the health risks of epoxy products was studied. Such a ranking system should inform the user of the harmfulness of different epoxies and stimulate research on less harmful products by product developers.

  18. Resin gathering in neotropical resin bugs (Insecta: Hemiptera: Reduviidae): functional and comparative morphology.

    Science.gov (United States)

    Forero, Dimitri; Choe, Dong-Hwan; Weirauch, Christiane

    2011-02-01

    Apiomerini (Reduviidae: Harpactorinae) collect plant resins with their forelegs and use these sticky substances for prey capture or maternal care. These behaviors have not been described in detail and morphological structures involved in resin gathering, transfer, and storage remain virtually undocumented. We here describe these behaviors in Apiomerus flaviventris and document the involved structures. To place them in a comparative context, we describe and document leg and abdominal structures in 14 additional species of Apiomerini that represent all but one of the 12 recent genera in the tribe. Based on these morphological data in combination with the behavioral observations on A. flaviventris, we infer behavioral and functional hypotheses for the remaining genera within the tribe Apiomerini. Setal abdominal patches for resin storage are associated with maternal care so far only documented for species of Apiomerus. Based on the occurrence of these patches in several other genera, we propose that maternal care is widespread within the tribe. Ventral abdominal glands are widespread within female Apiomerini. We propose that their products may prevent hardening of stored resins thus providing long-term supply for egg coating. Judging from the diverse setal types and arrangements on the front legs, we predict six different behavioral patterns of resin gathering within the tribe. Copyright © 2010 Wiley-Liss, Inc.

  19. Four Pentasaccharide Resin Glycosides from Argyreia acuta.

    Science.gov (United States)

    Yu, Bang-Wei; Sun, Jing-Jing; Pan, Jie-Tao; Wu, Xiu-Hong; Yin, Yong-Qin; Yan, You-Shao; Hu, Jia-Yan

    2017-03-11

    Four pentasaccharide resin glycosides, acutacoside F-I ( 1 - 4 ), were isolated from the aerial parts of Argyreia acuta . These compounds were characterized as a group of macrolactones of operculinic acid A, and their lactonization site of 11 S -hydroxyhexadecanoic acid was esterified at the second saccharide moiety (Rhamnose) at C-2. The absolute configuration of the aglycone was S . Their structures were elucidated by established spectroscopic and chemical methods.

  20. Rheology of Polyaniline Dispersions in Acrylic Resin

    OpenAIRE

    PLESU, Nicoleta; LIESCU, Smaranda; ILIA, Gheorghe

    2006-01-01

    Acrylic dispersions based on polyaniline were obtained and characterised. The polyaniline was obtained by chemical polymerisation of aniline in different organic acid containing phosphorous, in the presence of ammonium-peroxidisulphate as oxidant agent. The blends were obtained by mechanical dispersion of polyaniline in commercially available acrylic resin. The flow behaviour of these dispersions at different shear rates was studied. Furthermore, the resulting acrylic dispersions w...