WorldWideScience

Sample records for bis2-ethylhexyl sodium sulfosuccinate

  1. Influence of sodium bis(2-ethylhexyl) sulfosuccinate (AOT) on zinc electrodeposition

    Energy Technology Data Exchange (ETDEWEB)

    Lehr, I.L. [Instituto de Ingenieria Electroquimica y Corrosion (INIEC), Departamento de Ingenieria Quimica, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina); Saidman, S.B., E-mail: ssaidman@criba.edu.ar [Instituto de Ingenieria Electroquimica y Corrosion (INIEC), Departamento de Ingenieria Quimica, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina)

    2012-03-01

    This work is a study of the electrodeposition of zinc onto SAE 4140 steel electrodes using solutions containing zinc sulfate and bis(2-ethylhexyl) sodium sulfosuccinate (AOT). The influence of different parameters such as electrolyte concentration, electrodeposition time and temperature on the morphology of the electrodeposits was analyzed. The deposits were characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and X-ray diffraction. The variation of open circuit potential over time in chloride solutions was also evaluated. The nucleation-growth process and consequently the morphology of the electrodeposits are modified in the presence of AOT. The surfactant induces the formation of a porous deposit.

  2. Characterization of polypyrrole films electrosynthesized onto titanium in the presence of sodium bis(2-ethylhexyl) sulfosuccinate (AOT)

    Energy Technology Data Exchange (ETDEWEB)

    Flamini, D.O. [Instituto de Ingenieria Electroquimica y Corrosion (INIEC), Departamento de Ingenieria Quimica, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina); Saidman, S.B., E-mail: ssaidman@criba.edu.a [Instituto de Ingenieria Electroquimica y Corrosion (INIEC), Departamento de Ingenieria Quimica, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina)

    2010-04-15

    Films of polypyrrole (PPy) were successfully electrosynthesized onto titanium in neutral and alkaline solutions of sodium bis(2-ethylhexyl) sulfosuccinate (Aerosol OT or AOT) by potentiodynamic, galvanostatic and potentiostatic techniques. Results of the characterization of the films by cyclic voltammetry, scanning electron microscopy (SEM) and adhesion measurements are presented. It was found that the AOT molecule remains entrapped within the polymer matrix. The initial growth of the polymer produces electroactive toroidal deposits whereas for electropolymerization of longer duration the typical globular structure is developed. Adherence to Ti increases with deposition time and this result is interpreted as a consequence of the growth of a composite PPy/Ti oxide.

  3. Characterizing interfacial friction in bis(2-ethylhexyl) sodium sulfosuccinate reverse micelles from photoisomerization studies of carbocyanine derivatives

    Science.gov (United States)

    Gangamallaiah, V.; Dutt, G. B.

    2011-01-01

    Photoisomerization of two carbocyanine derivatives has been examined in bis(2-ethylhexyl) sodium sulfosuccinate (AOT) reverse micelles to understand the factors that govern this process in the interfacial region of organized assemblies. To this effect, fluorescence lifetimes and quantum yields of 3,3'-diethyloxadicarbocyanine iodide and merocyanine 540 have been measured in AOT/isooctane/water and AOT/cyclohexane/water reverse micellar systems as a function of the mole ratio of water to the surfactant, W. The nonradiative rate constants, which have been identified as the rates of photoisomerization for these solutes, were obtained from the experimentally measured parameters. The steady rise and subsequent saturation observed in the nonradiative rate constants upon increasing W has been rationalized in terms of micellar packing. An inverse correlation has been obtained between the nonradiative rate constants and the critical packing parameter, indicating that the interfacial friction experienced by the solute molecule is essentially described by this parameter.

  4. The effect of linoleic acid on pH inside sodium bis(2-ethylhexyl)sulfosuccinate reverse micelles in isooctane and on the enzymic activity of soybean lipoxygenase.

    Science.gov (United States)

    Rodakiewicz-Nowak, J; Maślakiewicz, P; Haber, J

    1996-06-01

    The effective pH of sodium bis(2-ethylhexyl)sulfosuccinate (AOT) reverse micelles (pHrm), containing buffers of different pH (pHst) and various amounts of linoleic acid, was studied within the range of compositions used to study the activity of soybean lipoxygenase in reverse micelles. Significant shifts of pHrm versus pHst were observed for the solutions of relatively higher pHst, dependent on linoleic acid and buffer concentrations. The effect diminished as pHst became closer to 7. When low-ionic-strength buffers were added to AOT solutions in isooctane, a significant buffering effect of linoleic acid in reverse micelles was observed. Solubilization of > 3 mM linoleic acid in micellar solutions containing 25 mM buffers gave the observed pHrm values almost independent of pHst. This effect diminished with the ionic strength of the buffering solution, but did not vanish even at 200 mM buffer. The observed effects result from the balance between ionization of linoleic acid and its partition between the water pool and the micellar interface. The enzymic activity of soybean lipoxygenase in the AOT reverse micellar solutions of the determined pHrm values was also studied. A significant reduction of the kinetics of the enzymic activity was observed, for all studied reverse micellar solutions. Changes of pHrm, caused by the presence of acidic substrate (linoleic acid) do not explain the observed reduction of activity directly through the effect on the enzyme. Due to unfavourable partition of the substrate between the microphases present in the systems, enhanced by reduction of pH at higher total concentrations of linoleic acid, the saturation of the enzyme with the substrate was not observed in the system and is difficult to attain experimentally in reverse micelles. A shift of the lipoxygenase activity/pHrm profile but negligible shift of the activity/pHst profile, with respect to aqueous buffer solutions, were observed. This indicates that either the information given

  5. Effects of water content and chain length of n-alkane on the interaction enthalpy between the droplets in water/sodium bis(2-ethylhexyl)-sulfosuccinate/n-alkane microemulsions.

    Science.gov (United States)

    Fan, Dashuang; Zheng, Peizhu; Ma, Yuanming; Yin, Tianxiang; Zhao, Jihua; Shen, Weiguo

    2015-04-14

    The concentration-dependent enthalpies of mixing for water/sodium bis(2-ethylhexyl)-sulfosuccinate (AOT)/n-alkane microemulsions with different water contents ω0 and chain lengths n of n-alkane were determined by isothermal titration microcalorimetry (ITC) and flow-mixing microcalorimetry at 298.15 K and used to calculate the interaction enthalpies (-ΔH(C)) between the droplets. It was found that -ΔH(C) increased with ω0, and changed from negative to positive at about ω0 = 10. The investigation of the dependence of -ΔH(C) on n revealed that the values of -ΔH(C) were negative and had a minimum for ω0 = 5; while they were positive and had a maximum for ω0 = 15. These phenomena were discussed based on the competition of the overlapping contribution of the surfactant tails between two neighbouring droplets and the penetration contribution of the solvent molecules into the surfactant tails. These results indicated the important role of entropy in the stability of the microemulsion systems.

  6. Micelles and reverse micelles in the nickel bis(2-ethylhexyl) sulfosuccinate/water/isooctane microemulsion.

    Science.gov (United States)

    Garza, Cristina; Carbajal-Tinoco, Mauricio D; Castillo, Rolando

    2004-12-01

    The ternary system Ni(2+)(AOT)(2) (nickel 2-bis[2-ethylhexyl] sulfosuccinate)/water/isooctane presents w/o and o/w microemulsions with a Winsor progression (2Phi-3Phi-2Phi), without the addition of salt; the "fish diagram" was obtained for alpha=0.5 and gamma=0.02-0.22. Using static and dynamic light scattering the micellar size, the ratio of water to surfactant, and the density of micelles for this system were estimated. In addition, the mean interfacial curvature as a function of temperature was obtained.

  7. Integral physicochemical properties of reverse micelles of sodium bis(2-ethylhexyl) sulfosuccinate (AOT)

    Science.gov (United States)

    Fedyaeva, O. A.; Shubenkova, E. G.; Poshelyuzhnaya, E. G.; Lutaeva, I. A.

    2016-08-01

    The effect the degree of hydration has on optical and electrophysical properties of water/AOT/ n-hexane system is studied. It is found that AOT reverse micelles form aggregates whose dimensions grow along with the degree of hydration and temperature. Aggregation enhances their electrical conductivity and shifts the UV spectrum of AOT reverse emulsions to the red region. Four states of water are found in the structure of AOT reverse micelles.

  8. Temperature-dependent solvation dynamics of water in sodium bis(2-ethylhexyl)sulfosuccinate/isooctane reverse micelles.

    Science.gov (United States)

    Mitra, Rajib Kumar; Sinha, Sudarson Sekhar; Pal, Samir Kumar

    2008-01-01

    In this paper, for the first time, we report a detailed study of the temperature-dependent solvation dynamics of a probe fluorophore, coumarin-500, in AOT/isooctane reverse micelles (RMs) with varying degrees of hydration (w0) of 5, 10, and 20 at four different temperatures, 293, 313, 328, and 343 K. The average solvation time constant becomes faster with the increase in w0 values at a particular temperature. The solvation dynamics of a RM with a fixed w0 value also becomes faster with the increase in temperature. The observed temperature-induced faster solvation dynamics is associated with a transition of bound- to free-type water molecules, and the corresponding activation energy value for the w0 = 5 system has been found to be 3.4 kcal mol-1, whereas for the latter two systems, it is approximately 5 kcal mol-1. Dynamic light scattering measurements indicate an insignificant change in size with temperature for RMs with w0 = 5 and 10, whereas for a w0 = 20 system, the hydrodynamic diameter increases with temperature. Time-resolved fluorescence anisotropy studies reveal a decrease in the rotational restriction on the probe with increasing temperature for all systems. Wobbling-in-cone analysis of the anisotropy data also supports this finding.

  9. Droplet polydispersity and shape fluctuations in AOT [bis(2-ethylhexyl)sulfosuccinate sodium salt] microemulsions studied by contrast variation small-angle neutron scattering

    DEFF Research Database (Denmark)

    Arleth, L.; Pedersen, J.S.

    2001-01-01

    Microemulsions consisting of AOT water, and decane or iso-octane are studied in the region of the phase diagram where surfactant covered water droplets are formed. The polydispersity and shape fluctuations of the microemulsion droplets are determined and compared in the two different alkane types....... Conductivity measurements show that there is a pronounced dependence of the temperature behavior of the microemulsion on the type of alkane used. In both cases the microemulsion droplets start to form larger aggregates when the temperature increases. But in the system with decane this aggregation temperature...... occurs at a temperature about 10 degreesC lower than in a similar system with iso-octane. Aggregation phenomena are avoided and the two systems are at approximately the same reduced temperature with respect to the aggregation temperature when the temperature of the AOT/D2O/decane microemulsion is 10...

  10. Contemporary carbon content of bis (2-ethylhexyl) phthalate in butter.

    Science.gov (United States)

    Tong, T; Ondov, J M; Buchholz, B A; VanDerveer, M C

    2016-01-01

    The fraction of naturally produced bis (2-ethylhexyl) phthalate (DEHP), a ubiquitous plasticizer known to contaminate packaged foods, was determined for each of five 1.10 kg samples of unsalted market butter by accelerator mass spectrometry (AMS). After extraction and concentration enrichment with liquid-liquid extraction, flash column chromatography, and preparative-scale high performance liquid chromatography, each sample provided ≈ 250 μg extracts of DEHP with carbon purity ranging from 92.5 ± 1.2% (n = 3, 1σ) to 97.1 ± 0.8% (n = 3, 1σ) as measured with gas chromatography mass spectrometry (GC-MS). After corrections for method blank DEHP, co-eluting compounds, and unidentified carbon, the mean fraction of naturally produced DEHP in butter was determined to be 0.16 ± 0.12 (n = 5, 1σ). To our knowledge, this is the first report of the contemporary fraction of DEHP isolated from market butter in the U.S.

  11. Liquid-liquid extraction of palladium(II) from nitric acid by bis(2-ethylhexyl) sulphoxide

    Energy Technology Data Exchange (ETDEWEB)

    Shukla, J.P. (Radiochemistry Division, Bhabha Atomic Research Centre, Trombay, Bombay 400085 (India)); Singh, R.K.; Sawant, S.R.; Varadarajan, N. (Power Reactor Fuel Reprocessing Plant, Bhabha Atomic Research Centre, Trombay, Bombay 400085 (India))

    1993-04-15

    The extraction of palladium(II) nitrate by bis(2-ethylhexyl) sulphoxide (BESO) was evaluated over a wide range of acidity, and BESO was shown to have a strong extraction ability toward this thiophilic 'soft' metal. Essentially quantitative extraction of trace and macro amounts of palladium is easily accomplished from about 8 M HNO 8 M HNO[sub 3] down to pH 2 solutions by 0.2 M BESO into toluene. Optimum conditions such as aqueous phase acidity, solvent, period of equilibration, aqueous to organic phase ratios, reagent concentration and strippant were established for the selective and reversible extraction and separation of palladium. Slope analyses applied to Pd(II) distribution experiments from nitrate solutions showed a predominant formation of the solvated organic phase complex Pd(NO[sub 3])[sub 2].2BESO. Recovery of the extractant from loaded palladium is easily accomplished by using sodium thiosulphate or a mixture of 2 M sodium carbonate+0.5 M ammonia solution. The extracted complex was characterized by elemental analysis and IR and UV-visible spectrometry, and its composition was confirmed to be Pd(NO[sub 3])[sub 2].2BESO

  12. 21 CFR 172.520 - Cocoa with dioctyl sodium sulfosuccinate for manufacturing.

    Science.gov (United States)

    2010-04-01

    ... manufacturing. 172.520 Section 172.520 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... sodium sulfosuccinate for manufacturing. The food additive “cocoa with dioctyl sodium sulfosuccinate for manufacturing,” conforming to § 163.117 of this chapter and § 172.810, is used or intended for use as a...

  13. 21 CFR 163.117 - Cocoa with dioctyl sodium sulfosuccinate for manufacturing.

    Science.gov (United States)

    2010-04-01

    ... manufacturing. 163.117 Section 163.117 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... Standardized Cacao Products § 163.117 Cocoa with dioctyl sodium sulfosuccinate for manufacturing. (a) Description. Cocoa with dioctyl sodium sulfosuccinate for manufacturing is the food additive complying with...

  14. Vaporization behavior of tetraoctylphosphonium bis(2-ethylhexyl)phosphate ionic liquid

    Science.gov (United States)

    McMurray, J. W.; Zhou, Y.; Luo, H. M.; Qu, J.

    2017-01-01

    The equilibrium vapor pressures, pe, of the ionic liquid tetraoctylphosphonium bis(2-ethylhexyl)phosphate ([P8888][DEHP]) over the temperature range 409-495 K were determined for the first time using mass loss Knudsen effusion. The pe versus temperature relationship compares well to 1-methyl-3-octylimidazolium bis(trifluoromethylsulfonyl)imide ([C8mim][NTf2]) but is lower than that of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C2mim][NTf2]) when measured using the same technique. The discrepancies between the pe determined in this work for [C8mim][NTf2] and [C2mim][NTf2] with previous studies is discussed. The enthalpy and entropy of vaporization for all three fluids are estimated from the Clasius-Clapeyron relation.

  15. Thallium extraction from hydrochloric acid media into a deep eutectic solvent using bis(2-ethylhexyl) phosphate

    Science.gov (United States)

    Tran, Kate; Volia, Merinda; Tereshatov, Evgeny; Folden, Charles, III

    2016-09-01

    The chemical properties of superheavy elements are relatively unknown due to their short half-lives and difficulty of production. In preparation for a future experiment to study the chemical properties of element 113, separation techniques have been used to study the behavior of its homologs, In and Tl. Previous work studied the liquid-liquid extraction of radioactive 201Tl (t1 / 2 = 3 . 04 d) from various concentrations of HCl into a mixture of menthol and lauric acid that formed a so-called deep eutectic solvent (DES). This work focuses on the effects of adding an extraction agent, bis(2-ethylhexyl) phosphate (HDEHP), to the DES on the efficiency of thallium extraction. The extraction of Tl(I) was generally poor, both with and without HDEHP added. In contrast, 111In (t1 / 2 = 2 . 80 d) showed significant extraction using HDEHP added to the same DES. This difference in behavior could potentially be exploited in a future experiment on the chemistry of element 113. National Science Foundation.

  16. Emerging dynamics in surfactant-based liquid mixtures: Octanoic acid/bis(2-ethylhexyl) amine systems

    Science.gov (United States)

    Calandra, Pietro; Mandanici, Andrea; Turco Liveri, Vincenzo; Pochylski, Mikolaj; Aliotta, Francesco

    2012-02-01

    This work focuses on the dynamic phenomena emerging in self-assembled transient intermolecular networks formed when two different surfactants are mixed. In particular, the relaxation processes in liquid mixtures composed by bis(2-ethylhexyl)amine (BEEA) and octanoic acid (OA) in the whole composition range has been investigated by dielectric spectroscopy and Brillouin spectroscopy. A thorough analysis of all the experimental data consistently suggests that, mainly driven by acid-base interactions arising when the two surfactants are mixed, supra-molecular aggregates formation causes the slowing down of molecular dynamics. This, in turn, reflects to longer-range relaxations. These changes have been found to be composition-dependent, involving strong departures of the mixture physico-chemical properties from an ideal behaviour, and reflecting the structural and dynamical features of local structures. In particular, the peculiar dynamic processes occurring in these local inter-molecular structures, have been found to be the factors responsible for the observed and quite surprising increase of direct-current conductivity which occurs when two different (and pretty non-conductive) surfactants are mixed. The discovery can be used not only to design novel materials for application purposes but also to shed more light on the basic principles regulating charge migration in structured liquid systems.

  17. The use of bis (-2-ethylhexyl) phosphoric acid for the extraction of zinc from concentrated ammonium chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Amer, S.; Luis, A.; Cuadra, A. de la; Caravaca, C.

    1994-01-01

    The extraction of zinc from concentrated ammonium chloride solutions by means of the bis(-2-ethylhexyl) phosphoric acid is studied. Mass balances and chemical equilibria relating the different chemical species in both phases are presented in order to establish a model describing the behaviour of the different species. Good agreement between experimental data and theoretical curves is obtained. A comparison of the zinc extraction from a strong complexing medium as that of concentrated ammonium chloride solutions with an uncomplexing zinc perchlorate solution is made, in order to see the influence of the complexing effect of the aqueous phase on zinc extraction. (Author) 36 p.

  18. Decoupling of dynamic processes in surfactant-based liquid mixtures: the case of lithium-containing bis(2-ethylhexyl)phosphoric acid/bis(2-ethylhexyl)amine systems.

    Science.gov (United States)

    Nicotera, Isabella; Oliviero Rossi, Cesare; Turco Liveri, Vincenzo; Calandra, Pietro

    2014-07-22

    Pure surfactant liquids and their binary mixtures, because of the amphiphilic nature of the molecules involved, can exhibit nanosegregation and peculiar transport properties. The idea that inspired this work is that the possibility of including in such media salts currently used for technological applications should lead to a synergy between the properties of the salt and those of the medium. Therefore, the dynamic features of bis(2-ethylhexyl)amine (BEEA) and bis(2-ethylhexyl)phosphoric acid (HDEHP) liquid mixtures were investigated as a function of composition and temperature by (1)H nuclear magnetic resonance (NMR) spectroscopy and rheometry. Inclusion of litium trifluoromethanesulfonate (LiT) has been investigated by infrared spectroscopy, pulsed field gradient NMR, and conductimetry methods to highlight the solubilizing and confining properties of these mixtures as well as the lithium conductivity. It was found that BEEA/HDEHP binary liquid mixtures show zero-threshold percolating self-assembly with a maximum in viscosity and a minimum in molecular diffusion at a 1:1 composition. Dissolution of LiT in such system can occur via confinement in the locally self-assembled polar domains. Despite this confinement, Li(+) conduction is scarcely dependent on the medium composition because of the possibility of a field-induced hopping decoupled by the structural and dynamical features of the medium.

  19. 21 CFR 172.810 - Dioctyl sodium sulfo-suc-cinate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Dioctyl sodium sulfo-suc-cinate. 172.810 Section 172.810 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... agent in the following fumaric acid-acidulated foods: Dry gelatin dessert, dry beverage base, and fruit...

  20. Effect of ultrasonication and Fenton oxidation on biodegradation of bis(2-ethylhexyl) phthalate (DEHP) in wastewater sludge.

    Science.gov (United States)

    Pham, T T H; Tyagi, R D; Brar, S K; Surampalli, R Y

    2011-02-01

    The presence of bis(2-ethylhexyl) phthalate (DEHP) and its metabolites, i.e. 2-ethylhexanol, 2-ethylhexanal, and 2-ethylhexanoic acid in wastewater sludge (WWS) were investigated during aerobic digestion and Bacillus thuringiensis (Bt)-based fermentation of WWS. Ultrasonication and Fenton oxidation pre-treatment was applied to improve biodegradability of WWS and bioavailability of the target compounds for digestion and fermentation. DEHP and 2-ethylhexanoic acid were observed at higher concentration, meanwhile 2-ethylhexanol and 2-ethylhexanal were observed at lower concentration in WWS. After 20-day aerobic digestion, DEHP removal was 72%, 89%, and 85%, and 2-ethylhexanoic acid removal was 71%, 84%, 79%, respectively for raw, ultrasonicated, and Fenton-oxidized sludges. Bt was found to degrade DEHP, leading to DEHP removal of 21%, 40%, and 30%, respectively for raw, ultrasonicated, and Fenton-oxidized sludges in the fermentation. The results suggested that aerobic stabilization and Bt-based fermentation can remove the phthalates, and pre-treatment of WWS was also effective in improvement of DEHP biodegradation. Hence, Bt-based biopesticide production from WWS can be applied safely when taking into consideration the phthalate contaminants.

  1. Rodent Thyroid, Liver, and Fetal Testis Toxicity of the Monoester Metabolite of Bis-(2-ethylhexyl) Tetrabromophthalate (TBPH), a Novel Brominated Flame Retardant Present in Indoor Dust

    OpenAIRE

    2012-01-01

    Background: Bis-(2-ethylhexyl) tetrabromophthalate (TBPH) is widely used as a replacement for polybrominated diphenyl ethers (PBDEs) in commercial flame retardant mixtures such as Firemaster 550. It is also used in a commercial mixture called DP 45. Mono-(2-ethyhexyl) tetrabromophthalate (TBMEHP) is a potentially toxic metabolite. Objectives: We used in vitro and rodent in vivo models to evaluate human exposure and the potential metabolism and toxicity of TBPH. Methods: Dust collected from ho...

  2. The Emulsion Polymerization of Each of Vinyl Acetate and Butyl Acrylate Monomers Using bis (2-ethylhexyl Maleate for Improving the Physicomechanical Properties of Paints and Adhesive Films

    Directory of Open Access Journals (Sweden)

    K. A. Shaffei

    2009-01-01

    Full Text Available Improving the water sensitivity of polyvinyl acetate PVAc films as well as pressure sensitivity, adhesion and washability of polybutyl acrylate were achieved by using bis (2-ethylhexyl maleate (BEHM. The emulsion polymerization kinetics of vinyl acetate and butyl acrylate in presence of BEHM was studied. The order of the polymerization reaction with respect to the BEHM in presence of each of vinyl acetate and butyl acrylate was studied. The physicomechanical properties of the polyvinyl acetate films and vinyl acetate-butyl acrylate copolymer films were studied in presence of BEHM and the obtained results were matched with those prepared in the presence of pluronic F 108 and showed superior values. The obtained mean average molecular weights were found to be smaller in presence of BEHM assuring the presence of chain transfer reaction.

  3. Effective remediation of phenol,2,4-bis(1,1-dimethylethyl) and bis(2-ethylhexyl) phthalate in farm effluent using Guar gum--A plant based biopolymer.

    Science.gov (United States)

    Kee, Yang Ling; Mukherjee, Sumona; Pariatamby, Agamuthu

    2015-10-01

    This study was carried out to evaluate the efficiency of Guar gum in removing Persistent Organic Pollutants (POPs), viz. phenol,2,4-bis(1,1-dimethylethyl) and bis(2-ethylhexyl) phthalate (DEHP), from farm effluent. The removal efficiency was compared with alum. The results indicated that 4.0 mg L(-1) of Guar gum at pH 7 could remove 99.70% and 99.99% of phenol,2,4-bis(1,1-dimethylethyl) and DEHP, respectively. Box Behnken design was used for optimization of the operating parameters for optimal POPs removal. Scanning Electron Microscopy (SEM) and Fourier Transform Infrared (FTIR) spectroscopy studies were conducted on the flocs. SEM micrographs showed numerous void spaces in the flocs produced by Guar gum as opposed to those produced by alum. This indicated why Guar gum was more effective in capturing and removal of suspended particles and POPs as compared to alum. FTIR spectra indicated a shift in the bonding of functional groups in the flocs produced by Guar gum as compared to raw Guar gum powder signifying chemical attachment of the organics present in the effluent to the coagulant resulting in their removal. Guar gum is highly recommended as a substitute to chemical coagulant in treating POPs due to its non-toxic and biodegradable characteristics.

  4. Controlled release of the pineal hormone melatonin from hydroxypropylmethylcellulose/sodium alginate matrices in aqueous media containing dioctyl sulfosuccinate.

    Science.gov (United States)

    Vlachou, Marilena; Tsiakoulia, Athanasia; Eikosipentaki, Aphrodite

    2007-06-01

    An investigation of the controlled release profile of mono-layered formulations of the hormone melatonin in modified aqueous media is described. The tablets used were comprised of hydroxypropylmethylcellulose (HPMC K15M) and sodium alginate with melatonin (fully soluble in the dioctyl sulfosuccinate (DSS) containing simulated intestinal solution). Three different sets of tablets (diameters 7.5, 10.0 and 13.0 mm) were tested with respect to the influence of their sizes on the hormone's release; the general trend observed was that tablets with larger surface area values had lower % release. A decrease in the value of W(o), obtained from the ratio [H(2)O]/[DSS], results to the predominance of DSS conformers in the aqueous media, which are less likely to solubilize melatonin effectively.

  5. 75 FR 34045 - Sodium 1,4-Dialkyl Sulfosuccinates; Exemption from the Requirement of a Tolerance

    Science.gov (United States)

    2010-06-16

    ... post-harvest uses, as well as, for application to animals. For ease of reading this document the sodium... antimicrobial hard surface cleaners) as well as from other, nonpesticidal, residential use products containing... pesticide formulations for pre-harvest and post- harvest uses, as well as for application to...

  6. Presence of the Corexit component dioctyl sodium sulfosuccinate in Gulf of Mexico waters after the 2010 Deepwater Horizon oil spill

    Science.gov (United States)

    Gray, James L.; Kanagy, Leslie K.; Furlong, Edward T.; Kanagy, Chris J.; McCoy, Jeff W.; Mason, Andrew; Lauenstein, Gunnar

    2014-01-01

    Between April 22 and July 15, 2010, approximately 4.9 million barrels of oil were released into the Gulf of Mexico from the Deepwater Horizon oil well. Approximately 16% of the oil was chemically dispersed, at the surface and at 1500 m depth, using Corexit 9527 and Corexit 9500, which contain dioctyl sodium sulfosuccinate (DOSS) as a major surfactant component. This was the largest documented release of oil in history at substantial depth, and the first time large quantities of dispersant (0.77 million gallons of approximately 1.9 million gallons total) were applied to a subsurface oil plume. During two cruises in late May and early June, water samples were collected at the surface and at depth for DOSS analysis. Real-time fluorimetry data was used to infer the presence of oil components to select appropriate sampling depths. Samples were stored frozen and in the dark for approximately 6 months prior to analysis by liquid chromatography/tandem mass spectrometry with isotope-dilution quantification. The blank-limited method detection limit (0.25 μg L−1) was substantially less than the U.S. Environmental Protection Agency’s (USEPA) aquatic life benchmark of 40 μg L−1. Concentrations of DOSS exceeding 200 μg L−1 were observed in one surface sample near the well site; in subsurface samples DOSS did not exceed 40 μg L−1. Although DOSS was present at high concentration in the immediate vicinity of the well where it was being continuously applied, a combination of biodegradation, photolysis, and dilution likely reduced persistence at concentrations exceeding the USEPA aquatic life benchmark beyond this immediate area.

  7. Presence of the Corexit component dioctyl sodium sulfosuccinate in Gulf of Mexico waters after the 2010 Deepwater Horizon oil spill.

    Science.gov (United States)

    Gray, James L; Kanagy, Leslie K; Furlong, Edward T; Kanagy, Chris J; McCoy, Jeff W; Mason, Andrew; Lauenstein, Gunnar

    2014-01-01

    Between April 22 and July 15, 2010, approximately 4.9 million barrels of oil were released into the Gulf of Mexico from the Deepwater Horizon oil well. Approximately 16% of the oil was chemically dispersed, at the surface and at 1500 m depth, using Corexit 9527 and Corexit 9500, which contain dioctyl sodium sulfosuccinate (DOSS) as a major surfactant component. This was the largest documented release of oil in history at substantial depth, and the first time large quantities of dispersant (0.77 million gallons of approximately 1.9 million gallons total) were applied to a subsurface oil plume. During two cruises in late May and early June, water samples were collected at the surface and at depth for DOSS analysis. Real-time fluorimetry data was used to infer the presence of oil components to select appropriate sampling depths. Samples were stored frozen and in the dark for approximately 6 months prior to analysis by liquid chromatography/tandem mass spectrometry with isotope-dilution quantification. The blank-limited method detection limit (0.25 μg L(-1)) was substantially less than the U.S. Environmental Protection Agency's (USEPA) aquatic life benchmark of 40 μg L(-1). Concentrations of DOSS exceeding 200 μg L(-1) were observed in one surface sample near the well site; in subsurface samples DOSS did not exceed 40 μg L(-1). Although DOSS was present at high concentration in the immediate vicinity of the well where it was being continuously applied, a combination of biodegradation, photolysis, and dilution likely reduced persistence at concentrations exceeding the USEPA aquatic life benchmark beyond this immediate area.

  8. Improvement in enzyme activity and stability by addition of low molecular weight polyethylene glycol to sodium bis(2-ethyl-L-hexyl)sulfosuccinate/isooctane reverse micellar system.

    Science.gov (United States)

    Talukder, M M R; Takeyama, T; Hayashi, Y; Wu, J C; Kawanishi, T; Shimizu, N; Ogino, C

    2003-08-01

    The activity and stability of Chromobacterium viscosum lipase (glycerolester hydrolase, EC 3.1.1.3)-catalyzed olive oil hydrolysis in sodium bis (2-ethyl-l-hexyl)sulfosuccinate (AOT)/isooctane reverse micelles is increased appreciably when low molecular weight polyethylene glycol (PEG 400) is added to the reverse micelles. To understand the effect of PEG 400 on the phase behavior of the reverse micellar system, the phase diagram of AOT/ PEG 400/water/isooctane system was studied. The influences of relevant parameters on the catalytic activity in AOT/PEG 400 reverse micelles were investigated and compared with the results in the simple AOT reverse micelles. In the presence of PEG 400, the linear decreasing trend of the lipase activity with AOT concentration, which is observed in the simple AOT reverse micelles, disappeared. Enzyme entrapped in AOT/PEG reverse micelles was very stable, retaining >75% of its initial activity after 60 d, whereas the half-life in simple AOT reverse micelles was 38 d. The kinetics parameter maximum velocity (Vmax) exhibiting the temperature dependence and the activation energy obtained by Arrhenius plot was suppressed significantly by the addition of PEG 400.

  9. Dynamic and spectroscopic studies of nano-micelles comprising dye in water/ dioctyl sodium sulfosuccinate /decane droplet microemulsion at constant water content

    Science.gov (United States)

    Rahdar, Abbas; Almasi-Kashi, Mohammad

    2017-01-01

    In the present work, the dynamic and spectroscopic properties of water-in-decane dioctyl sodium sulfosuccinate (AOT) microemulsions comprising dye, Rhodamine B (RB), were studied by varying content of decane at the constant water content (W = 20), by using dynamic light scattering (DLS), UV/visible, and fluorescence techniques. The characterization results of DLS of AOT micelles showed that by decreasing concentration of Rhodamine B in the water/AOT/decane microemulsion, the inter-droplet interactions changed from attractive to repulsive as the mass fraction of nano-droplets (MFD) increased. A deviation in the absorption spectra of Rhodamine B from the Beer's law at the high Rhodamine B concentration (0.001) was observed in the AOT reversed micelles. The Quenching in the emission intensity of AOT droplets comprising Rhodamine B and red shift in λmax of fluorescence of dye was observed as a function of concentration of RB in AOT RMs. The Stokes shift of AOT droplets containing the high concentration of RB, increased with mass fraction of nano-droplet (MFD), whereas at the low Rhodamine B concentration, its variation remained constant up to MFD = 0.07, and then increased.

  10. Structural Studies on Nonequilibrium Microstructures of Dioctyl Sodium Dodecyl Sulfosuccinate (Aerosol-OT in p-Toluenesulfonic Acid and Phosphatidylcholine

    Directory of Open Access Journals (Sweden)

    M. K. Temgire

    2012-01-01

    Full Text Available Several microstructures are evolved at the interface when sparingly soluble solid surfactants come in contact with water. One class of these microstructures is termed as “myelin figures”; these were observed when phosphatidylcholine came in contact with water. Although the myelins are initially simple rod-like, complex forms like helices, coils and so forth. appear in the later stage. Finally, the myelins fuse together to form a complex mosaic-like structure. When studied by taking a cross-section using cryoscanning electron microscopy, it revealed concentric circular pattern inside the myelin figures. The cross-sections of (dioctyl sodium dodecyl sulfosiccinate AOT/water system myelin internal structures were lost. When p-toluenesulfonic acid (PTS 2 wt% was present in the water phase, AOT myelins revealed the internal microstructures. It has annular concentric ring-like structure with a core axon at the centre. Further investigation revealed new microstructures for the first time having multiple axons in the single-myelin strand.

  11. Aggregation of sulfosuccinate surfactants in water

    Energy Technology Data Exchange (ETDEWEB)

    Magid, L.J.; Daus, K.A.; Butler, P.D.; Quincy, R.B.

    1983-12-22

    The aggregation of sodium di-n-alkyl sulfosuccinates in water (H/sub 2/O and D/sub 2/O at 45/sup 0/C) has been investigated. A self-consistent picture of the dependence of sodium ion binding on surfactant concentration is obtained from emf measurements, conductimetry, and small-angle neutron scattering (SANS) measurements. The concentration dependence of the micellar agregation number for the sulfosuccinates and related double-tailed surfactants depends markedly on surfactant solubility. A sphere-to-disk transition in micellar shape, which might have been expected as a precursor to formation of a lamellar mesophase, was not observed as the surfactant concentration was increased. 8 figures, 2 tables.

  12. Porphyrins in Reverse Micelles:the Side-chain Length and the Triplet-state Lifetime

    Institute of Scientific and Technical Information of China (English)

    Jun Hua YU; Yu Xiang WENG; Xue Song WANG; Lei ZHANG; Bao Wen ZHANG; Yi CAO

    2003-01-01

    Using bis(2-ethylhexyl) sodium sulfosuccinate (AOT) as surfactant, two amphiphilic porphyrin terminated with imidazole were studied in AOT/iso-octane/water reverse micelles, intending to mimic the relationship between microenvironments in organism and the amphiphilic properties of porphyrins for photodynamic therapy drugs.

  13. Water in oil microemulsions as reaction media for a Diels-Alder reaction between N-ethylmaleimide and cyclopentadiene

    NARCIS (Netherlands)

    Engberts, JBFN; Fernandez, E; Garcia-Rio, L; Leis, J.R.

    2006-01-01

    The Diels-Alder reaction between N-ethylmaleimide and cyclopentadiene in water/AOT/isooctane microemulsions, where AOT denotes sodium bis(2-ethylhexyl) sulfosuccinate, was studied. The rate of the reaction was found to be higher than that obtained in pure isooctane, irrespective of the particular mi

  14. Water in oil microemulsions as reaction media for a Diels-Alder reaction between N-ethylmaleimide and cyclopentadiene

    NARCIS (Netherlands)

    Engberts, JBFN; Fernandez, E; Garcia-Rio, L; Leis, J.R.

    2006-01-01

    The Diels-Alder reaction between N-ethylmaleimide and cyclopentadiene in water/AOT/isooctane microemulsions, where AOT denotes sodium bis(2-ethylhexyl) sulfosuccinate, was studied. The rate of the reaction was found to be higher than that obtained in pure isooctane, irrespective of the particular

  15. Fluorescence dynamics of green fluorescent protein in AOT reversed micelles

    NARCIS (Netherlands)

    Uskova, M.A.; Borst, J.W.; Hink, M.A.; Hoek, van A.; Schots, A.; Klyachko, N.L.; Visser, A.J.W.G.

    2000-01-01

    We have used the enhanced green fluorescent protein (EGFP) to investigate the properties of surfactant-entrapped water pools in organic solvents (reversed micelles) with steady-state and time-resolved fluorescence methods. The surfactant used was sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and the

  16. Effects of Crude Oil/Dispersant Mixture and Dispersant Components on PPARγ Activity in Vitro and in Vivo: Identification of Dioctyl Sodium Sulfosuccinate (DOSS; CAS #577-11-7) as a Probable Obesogen

    Science.gov (United States)

    Temkin, Alexis M.; Bowers, Robert R.; Magaletta, Margaret E.; Holshouser, Steven; Maggi, Adriana; Ciana, Paolo; Guillette, Louis J.; Bowden, John A.; Kucklick, John R.; Baatz, John E.; Spyropoulos, Demetri D.

    2015-01-01

    Background The obesity pandemic is associated with multiple major health concerns. In addition to diet and lifestyle, there is increasing evidence that environmental exposures to chemicals known as obesogens also may promote obesity. Objectives We investigated the massive environmental contamination resulting from the Deepwater Horizon (DWH) oil spill, including the use of the oil dispersant COREXIT in remediation efforts, to determine whether obesogens were released into the environment during this incident. We also sought to improve the sensitivity of obesogen detection methods in order to guide post-toxicological chemical assessments. Methods Peroxisome proliferator–activated receptor gamma (PPARγ) transactivation assays were used to identify putative obesogens. Solid-phase extraction (SPE) was used to sub-fractionate the water-accommodated fraction generated by mixing COREXIT, cell culture media, and DWH oil (CWAF). Liquid chromatography–mass spectrometry (LC-MS) was used to identify components of fractionated CWAF. PPAR response element (PPRE) activity was measured in PPRE-luciferase transgenic mice. Ligand-binding assays were used to quantitate ligand affinity. Murine 3T3-L1 preadipocytes were used to assess adipogenic induction. Results Serum-free conditions greatly enhanced the sensitivity of PPARγ transactivation assays. CWAF and COREXIT had significant dose-dependent PPARγ transactivation activities. From SPE, the 50:50 water:ethanol volume fraction of CWAF contained this activity, and LC-MS indicated that major components of COREXIT contribute to PPARγ transactivation in the CWAF. Molecular modeling predicted several components of COREXIT might be PPARγ ligands. We classified dioctyl sodium sulfosuccinate (DOSS), a major component of COREXIT, as a probable obesogen by PPARγ transactivation assays, PPAR-driven luciferase induction in vivo, PPARγ binding assays (affinity comparable to pioglitazone and arachidonic acid), and in vitro murine

  17. 壬基酚聚氧乙烯醚琥珀酸二酯磺酸钠的合成及染色应用%Preparation of nonylphenol polyoxyethylene ether sodium sulfosuccinate and its application in dyeing

    Institute of Scientific and Technical Information of China (English)

    丁阳; 季定纬; 黄丹

    2016-01-01

    以烷基酚聚氧乙烯醚、马来酸酐和亚硫酸氢钠为主要反应物,采用超声-微波协同技术合成了烷基酚聚氧乙烯醚型磺基琥珀酸二酯钠盐Gemini表面活性剂,并用FT-IR和1H-NMR对产物结构进行表征.将其应用于毛/涤混纺织物分散染料的一浴法染色.探讨了pH、浴比、温度和NS用量对染色效果的影响,毛/涤混纺织物分散染料一浴法染色最佳染色工艺条件为:染液pH =3~4,浴比=25∶1,w(NS)=3% (owf),染色温度为95℃.在此工艺条件下,分散橙30、分散蓝2BW、分散红73和分散红SE-F3B的染色效果均有提升,且色牢度达4级以上.在染色体系中添加NS可以降低染色温度,显著提高分散染料的上染率.%An alkylphenol polyoxyethylene ether sulfosuccinate ester sodium salt Gemini surfactant is prepared by ultrasonic-microwave synergistic method using alkylphenol ethoxylate,maleic anhydride and sodium bisulfite as main raw materials.The structure of resulting products is characterized by FTIR and 1HNMR.This Gemini surfactant is then applied to one bath dyeing process of.wool/polyester blended fabric.The influences of pH value,bath ratio,dyeing temperature and the dosage of auxiliary agent on the dyeing effects are discussed.The optimized dyeing conditions are:3-4 of pH value,25∶1 of bath ratio,95℃ of dyeing temperature,3% (owl) of w(NS).Under this condition,the dyeing effects of Disperse Orange 30,Disperse Blue 2BW,Disperse Red 73 and Disperse Red SE-F3B are all improved,and the fastness of wet rubbing is 4 or/and 4-5 grade.The dye-uptake and K/S value can be significantly increased with the auxiliary agent NS in the dyeing process.

  18. Spontaneous vesicle formation from DSB/AOT mixed system

    Institute of Scientific and Technical Information of China (English)

    CHEN Wenjun; ZHAI Limin; LI Ganzuo; MENG Xiangguang; ZENG Xiancheng

    2003-01-01

    Spontaneous vesicles from the aqueous mixtures of dodecyl sulfonate betaine (DSB) and sodium bis (2-ethylhexyl) sulfosuccinate (AOT) at certain mixingratios have been demonstrated by using calorimetry, freeze-frac- ture transmission electronic microscopy (TEM), negative- staining TEM and dynamic light scattering (DLS) methods. The addition of NaCl will promote vesicle formation and the heat effect of monodisperse vesicle system is greatest. Meanwhile the mechanism was analyzed from the viewpoint of packing parameter f, molecular geometry structure and interaction.

  19. Layer-by-layer Assembly of Noble Metal Nanoparticles on Glassy Carbon Electrode

    Institute of Scientific and Technical Information of China (English)

    CHEN Da; ZHENG Long-Zhen

    2008-01-01

    Silver,gold,platinum and palladium nanoparticles were initially prepared in the AOT[sodium bis(2-ethylhexyl)-sulfosuccinate]micelle and characterized by ultraviolet-visible spectroscopy,transmission electron macroscopy,X-ray diffraction,Fourier transform-infrared spectroscopy,and zeta potential analysis.The negatively charged Pt nanoparticles were self-assembled on a glassy carbon electrode by a layer-by-layer method and the modified electrode electrocatalytic reactivity toward methanol oxidation was studied.

  20. Determination of the anionic surfactant di(ethylhexyl) sodium sulfosuccinate in water samples collected from Gulf of Mexico coastal waters before and after landfall of oil from the Deepwater Horizon oil spill, May to October, 2010

    Science.gov (United States)

    Gray, James L.; Kanagy, Leslie K.; Furlong, Edward T.; McCoy, Jeff W.; Kanagy, Chris J.

    2011-01-01

    On April 22, 2010, the explosion on and subsequent sinking of the Deepwater Horizon oil drilling platform resulted in the release of crude oil into the Gulf of Mexico. At least 4.4 million barrels had been released into the Gulf of Mexico through July 15, 2010, 10 to 29 percent of which was chemically dispersed, primarily using two dispersant formulations. Initially, the dispersant Corexit 9527 was used, and when existing stocks of that formulation were exhausted, Corexit 9500 was used. Over 1.8 million gallons of the two dispersants were applied in the first 3 months after the spill. This report presents the development of an analytical method to analyze one of the primary surfactant components of both Corexit formulations, di(ethylhexyl) sodium sulfosuccinate (DOSS), the preliminary results, and the associated quality assurance/quality control (QA/QC) from samples collected from various points on the Gulf Coast between Texas and Florida. Seventy water samples and 8 field QC samples were collected before the predicted landfall of oil (pre-landfall) on the Gulf Coast, and 51 water samples and 10 field QC samples after the oil made landfall (post-landfall). Samples were collected in Teflon(Registered) bottles and stored at -20(degrees)C until analysis. Extraction of whole-water samples used sorption onto a polytetrafluoroethylene (PTFE) filter to isolate DOSS, with subsequent 50 percent methanol/water elution of the combined dissolved and particulate DOSS fractions. High-performance liquid chromatography/tandem mass spectrometry (LC/MS/MS) was used to identify and quantify DOSS by the isotope dilution method, using a custom-synthesized 13C4-DOSS labeled standard. Because of the ubiquitous presence of DOSS in laboratory reagent water, a chromatographic column was installed in the LC/MS/MS between the system pumps and the sample injector that separated this ambient background DOSS contamination from the sample DOSS, minimizing one source of blank contamination

  1. Safety Assessment of Alkyl PEG Sulfosuccinates as Used in Cosmetics.

    Science.gov (United States)

    Johnson, Wilbur; Heldreth, Bart; Bergfeld, Wilma F; Belsito, Donald V; Hill, Ronald A; Klaassen, Curtis D; Liebler, Daniel C; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Andersen, F Alan

    2015-09-01

    The Cosmetic Ingredient Review (CIR) Expert Panel (Panel) reviewed the safety of alkyl polyethylene glycol (PEG) sulfosuccinates, which function in cosmetics mostly as surfactants/cleansing agents. Although these ingredients may cause ocular and skin irritation, dermal penetration is unlikely because of the substantial polarity and molecular size of these ingredients. The Panel considered the negative oral carcinogenicity and reproductive and developmental toxicity data on chemically related laureths (PEG lauryl ethers) and negative repeated dose toxicity and skin sensitization data on disodium laureth sulfosuccinate supported the safety of these alkyl PEG sulfosuccinates in cosmetic products, but. The CIR Expert Panel concluded that the alkyl PEG sulfosuccinates are safe in the present practices of use and concentration when formulated to be nonirritating.

  2. Electrodeposition of polypyrrole onto NiTi and the corrosion behaviour of the coated alloy

    Energy Technology Data Exchange (ETDEWEB)

    Flamini, D.O. [Instituto de Ingenieria Electroquimica y Corrosion (INIEC), Departamento de Ingenieria Quimica, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina); Saidman, S.B. [Instituto de Ingenieria Electroquimica y Corrosion (INIEC), Departamento de Ingenieria Quimica, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina)], E-mail: ssaidman@criba.edu.ar

    2010-01-15

    Polypyrrole (PPy) films were electrodeposited onto nickel--titanium alloy (NiTi) employing sodium bis(2-ethylhexyl) sulfosuccinate (Aerosol OT or AOT) solutions. Polarizing anodically NiTi samples recovered by PPy in a monomer-free solution increases adhesion of the coating. Electrochemical techniques, scanning electron microscopy (SEM) and element analysis were used in determining the corrosion performance of the coated samples in chloride solution. The polymer improves the corrosion performance at the open circuit potential and at potentials where the bare substrate suffers pitting attack. The improvement in both, adhesion and corrosion performance, is discussed considering substrate/polymer interaction, overoxidation of PPy and the role played by AOT.

  3. Phase behavior of supercritical CO2 microemulsion with food-grade surfactant AOT

    Institute of Scientific and Technical Information of China (English)

    ZHOU Yongsheng; AN Xueqin; SHEN Weiguo; ZHANG Yinghua

    2006-01-01

    Phase behavior of scCO2 microemulsion formed with food grade surfactant sodium bis-(2-ethylhexyl) sulfosuccinate (AOT) was studied. Critical microemulsion concentration (cμc) was deduced from the dependence of pressure of cloud points on the concentration of surfactant AOT at constant temperature and water concentration. The results show that there are transition points on the cloud point curve in a very narrow range of concentration of surfactant AOT. The transition points were changed with the temperature and water concentration. These phenomena show that lower temperature is suitable to forming microemulsion droplet and the microemulsion with high water concentration is likely to absorb more surfactants to structure the interface.

  4. Fractal lattice of gelatin nanoglobules

    Science.gov (United States)

    Novikov, D. V.; Krasovskii, A. N.

    2012-11-01

    The globular structure of polymer coatings on a glass, which were obtained from micellar solutions of gelatin in the isooctane-water-sodium (bis-2-ethylhexyl) sulfosuccinate system, has been studied using electron microscopy. It has been shown that an increase in the average globule size is accompanied by the formation of a fractal lattice of nanoglobules and a periodic physical network of macromolecules in the coating. The stability of such system of the "liquid-in-a-solid" type is limited by the destruction of globules and the formation of a homogeneous network structure of the coating.

  5. Chromatographic Separation Method for the Simulant Mixture of Triisopropyl Phosphite and Bis(2-Ethylhexyl) Hydrogen Phosphite

    Science.gov (United States)

    1991-08-01

    that of diisopropyl hydrogen phosphite (DIP) that could yield an error in the purity results if coelu- tion with TIP occurs. The DIP component is a...source of potential error if it is not completely separated from the TIP. The purpose of this investigation is to perform the initial GC development...8217 Retention Time 2 (min) Area3 1. 2-propanol 1.1 981078 2. TIP 3.44 15685456 3. DIP 5.68 7205570 4. TIPO 1.15 3584104 5. --- 14.63 720318 6. 17.63

  6. Synthesis of sol–gel silica particles in reverse micelles with mixed-solvent polar cores: tailoring nanoreactor structure and properties

    Energy Technology Data Exchange (ETDEWEB)

    Bürglová, Kristýna; Hlaváč, Jan [Institute of Molecular and Translational Medicine, Faculty of Medicine and Dentistry (Czech Republic); Bartlett, John R., E-mail: jbartlett@usc.edu.au [University of the Sunshine Coast, Faculty of Science, Health, Education and Engineering (Australia)

    2015-07-15

    In this paper, we describe a new approach for producing metal oxide nano- and microparticles via sol–gel processing in confined media (sodium bis(2-ethylhexyl)sulfosuccinate reverse micelles), in which the chemical and physical properties of the polar aqueous core of the reverse micelles are modulated by the inclusion of a second polar co-solvent. The co-solvents were selected for their capacity to solubilise compounds with low water solubility and included dimethylsulfoxide, dimethylformamide, ethylene glycol, n-propanol, dimethylacetamide and N-methylpyrrolidone. A broad range of processing conditions across the sodium bis(2-ethylhexyl)sulfosuccinate/cyclohexane/water phase diagram were identified that are suitable for preparing particles with dimensions <50 to >500 nm. In contrast, only a relatively narrow range of processing conditions were suitable for preparing such particles in the absence of the co-solvents, highlighting the role of the co-solvent in modulating the properties of the polar core of the reverse micelles. A mechanism is proposed that links the interactions between the various reactive sites on the polar head group of the surfactant and the co-solvent to the nucleation and growth of the particles.

  7. Flavonoid-surfactant interactions: A detailed physicochemical study

    Science.gov (United States)

    Singh, Onkar; Kaur, Rajwinder; Mahajan, Rakesh Kumar

    2017-01-01

    The aim of this article is to study the interactions between flavonoids and surfactants with attention of finding the probable location of flavonoids in micellar media that can be used for controlling their antioxidant behavior. In present study, the micellar and interfacial behavior of twin tailed anionic surfactants viz. sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and sodium bis(2-ethylhexyl)phosphate (NaDEHP) in the presence of two flavonoids, namely quercetin (QUE) and kaempferol (KFL) have been studied by surface tension measurements. UV-visible, fluorescence and differential pulse voltammetric (DPV) measurements have been employed to predict the probable location of flavonoids (QUE/KFL) within surfactant (AOT/NaDEHP) aggregates. Dynamic light scattering (DLS) measurements further confirmed the solubilization of QUE/KFL in AOT/NaDEHP aggregates deduced from increased hydrodynamic diameter (Dh) of aggregates in the presence of flavonoids. Both radical scavenging activity (RSA) and degradation rate constant (k) of flavonoids are found to be higher in NaDEHP micelles as compared to AOT micelles.

  8. Synthesis of Silver Nanoparticles by Precipitation in Bicontinuous Microemulsions

    Directory of Open Access Journals (Sweden)

    Pamela Y. Reyes

    2010-01-01

    Full Text Available Silver nanoparticles precipitation was carried out at 70∘C in bicontinuous microemulsions stabilized with a mixture of surfactants sodium bis (2-ethylhexyl sulfosuccinate/sodium dodecyl sulfate (2/1, w/w containing an aqueous solution of 0.5 M silver nitrate and toluene as organic phase. Various concentrations of aqueous solution of sodium borohydride (precipitating agent and their dosing times on microemulsions were studied. Regardless of dosing time, higher and medium concentrations of precipitating agent promoted the formation of worm-like nanostructures, while the lowest concentration allowed to obtain a mixture of isolated silver nanoparticles (mean diameter ≈3 nm and worm-like nanostructures. Experimental yields much higher than those typical in precipitation of silver nanoparticles in reverse microemulsions were obtained. An explanation for formation of worm-like nanostructures based on the development of local zones inside the microemulsions channels with high particle concentrations was proposed.

  9. Optimization of Indium Recovery and Separation from LCD Waste by Solvent Extraction with Bis(2-ethylhexyl Phosphate (D2EHPA

    Directory of Open Access Journals (Sweden)

    Jiaxu Yang

    2014-01-01

    Full Text Available Indium tin oxide (ITO is currently the choice of electrode material in liquid crystal displays (LCDs. D2EHPA is known to be an extractant that can be used to selectively recover indium from 1 M sulfuric acid. In order to optimize the extraction and separation of indium from LCD waste, the effects of pH, temperature, time, and extractant concentration on the distribution ratios of In(III and the major impurities such as Al(III, Cu(II, Fe(III, and Zn(II were investigated. Metal concentrations in the aqueous feed were based on the concentrations found in the leach liquor of LCD panel glass at 0.1 g/mL S/L ratio. This study showed that extraction of indium could be increased at 293 K. Furthermore, by increasing D2EHPA concentration from 0.1 M to 0.25 M, extraction of indium could be increased from 70% to >95%.

  10. DISTRIBUTION OF LANTHANIDE AND ACTINIDE ELEMENTS BETWEEN BIS-(2-ETHYLHEXYL)PHOSPHORIC ACID AND BUFFERED LACTATE SOLUTIONS CONTAINING SELECTED COMPLEXANTS

    Energy Technology Data Exchange (ETDEWEB)

    Rudisill, Tracy S.; Diprete, David P.; Thompson, Major C.

    2013-04-15

    With the renewed interest in the closure of the nuclear fuel cycle, the TALSPEAK process is being considered for the separation of Am and Cm from the lanthanide fission products in a next generation reprocessing plant. However, an efficient separation requires tight control of the pH which likely will be difficult to achieve on a large scale. To address this issue, we measured the distribution of lanthanide and actinide elements between aqueous and organic phases in the presence of complexants which were potentially less sensitive to pH control than the diethylenetriaminepentaacetic (DTPA) used in the process. To perform the extractions, a rapid and accurate method was developed for measuring distribution coefficients based on the preparation of lanthanide tracers in the Savannah River National Laboratory neutron activation analysis facility. The complexants tested included aceto-, benzo-, and salicylhydroxamic acids, N,N,N',N'-tetrakis(2-pyridylmethyl)ethylenediamine (TPEN), and ammonium thiocyanate (NH{sub 4}SCN). The hydroxamic acids were the least effective of the complexants tested. The separation factors for TPEN and NH{sub 4}SCN were higher, especially for the heaviest lanthanides in the series; however, no conditions were identified which resulted in separations factors which consistently approached those measured for the use of DTPA.

  11. Electromembrane extraction of polar basic drugs from plasma with pure bis(2-ethylhexyl) phosphite as supported liquid membrane

    DEFF Research Database (Denmark)

    Huang, Chuixiu; Seip, Knut Fredrik; Gjelstad, Astrid

    2016-01-01

    , electrolysis in the sample and acceptor solution was kept at an acceptable level with no detrimental consequences. For the polar model analytes, representing a log P range from -0.40 to 1.32, recoveries in the range 25-91% were obtained from human plasma. Strong hydrogen bonding and dipole interactions were...... probably responsible for efficient transfer of the model analytes into the SLM, and this is the first report on efficient EME of highly polar analytes without using any ionic carrier in the SLM....

  12. FT-IR studies on the conformation and effective head-group area of AOT molecules in W/O microemulsions

    Institute of Scientific and Technical Information of China (English)

    周国伟; 鲍猛; 李干佐; 陈文君

    2002-01-01

    Using Fourier transform infrared(FT-IR) spectroscopy technique, the carbonyl stretching vibration bands of AOT in sodium bis(2-ethylhexyl)sulfosuccinate (AOT)/isooctane/water reverse (W/O) microemulsions system have been investigated by least square curve fitting. The results indicate that an asymmetric adsorbed peak of carbonyl stretching vibration of AOT molecule is situated in (1739 ± 1) and (1725 ± 2) cm-1. The two peaks correspond to different carbonyls in gauche conformation and trans conformation of AOT molecules, respectively. With different water contents (W0), the variations of peak intensity ratio (/= l1739/l1725) reflect the change of the ratio for the two conformation populations and the variations of the effective head-group area of AOT molecule have relations to the ratio of two conformation populations.

  13. Formation of reverse micelles in supercritical carbon dioxide and its thermodynamics

    Institute of Scientific and Technical Information of China (English)

    WEN Zhen; DANG Zhi; ZONG Minhua; ZHU Zhixin

    2007-01-01

    The solubilization behavior of methyl orange as a solvation probe in multiple systems composed of supercritical carbon dioxide,surfactants and co-solvents,is studied.It is coneluded that some surfactants,such as sodium bis-(2-ethylhexyl)sulfosuccinate(AOT)and isooctyl phenol polyethoxylate (TX-10),could form reverse micelles in supercritical carbon dioxide under the action of butanol.The formation of reverse micelles is a spontaneous process thermodynamically.Specifically for the nonionic surfactant TX-10,the formation of reverse micelles is dependent on the entropy increase in the system,while for the anionic surfactant AOT,the micellization is mainly dominated by the increase in enthalpy at higher temperatures,but by the increase in entropy at lower temperatures.

  14. Separating excess surfactant from silver and gold nanoparticles in micellar concentrates by means of nonaqueous electrophoresis

    Science.gov (United States)

    Bulavchenko, A. I.; Demidova, M. G.; Popovetskiy, P. S.; Podlipskaya, T. Yu.; Plyusnin, P. E.

    2017-08-01

    It is shown by physicochemical means (IR Fourier spectroscopy, CHN-analysis with preliminary sorption of surfactant on SiO2) that the content of sodium bis(2-ethylhexyl)sulfosuccinate (AOT) in an electrophoretic concentrate remains unchanged during the electrophoretic concentration of silver and gold nanoparticles. Diluting the concentrate and carrying out the second stage of electrophoresis reduces the concentration of surfactant from 0.25 to 0.015 M while maintaining the mass concentration of nanoparticles. Nanoparticles in organosols before and after electrophoresis are characterized by means of photon correlation spectroscopy, phase analysis light scattering, and spectrophotometry. Conducting films on glass substrates are obtained from concentrates with a different contents of surfactant via water-alcohol treatment and thermolysis.

  15. Stabilization of {alpha}-amylase by using anionic surfactant during the immobilization process

    Energy Technology Data Exchange (ETDEWEB)

    El-Batal, A.I. [National Center for Radiation Research and Technology, P.O. Box 29, Nasr City, Cairo (Egypt); Atia, K.S. [Nuclear Research Center, Radioisotopes Applications Division, Abo-Zable, P.O. Box 13759, Cairo (Egypt)]. E-mail: ks_atia@yahoo.com; Eid, M. [National Center for Radiation Research and Technology, P.O. Box 29, Nasr City, Cairo (Egypt)

    2005-10-01

    This work describes the entrapment of {alpha}-amylase into butylacrylate-acrylic acid copolymer (BuA/AAc) using {gamma} irradiation. The effect of an anionic surfactant (AOT), the reuse efficiency, and kinetic behavior of immobilized {alpha}-amylase were studied. Covering of {alpha}-amylase with bis-(2-ethylhexyl)sulfosuccinate sodium salt (AOT) made the enzyme more stable than the uncovered form. The hydrolytic activity of the pre-coated immobilized {alpha}-amylase was increased below the critical micelle concentration (cmc) (10mmol/L). The results showed an increase in the relative activity with increase in the degree of hydration. The pre-coated immobilized {alpha}-amylase showed a higher k{sub cat}/K{sub m} and lower activation energy compared to the free and uncoated-immobilized preparation, respectively. The results suggest that the immobilization of {alpha}-amylase is a potentially useful approach for commercial starch hydrolysis in two-phase systems.

  16. A reliable and reproducible method for the lipase assay in an AOT/isooctane reversed micellar system: modification of the copper-soap colorimetric method.

    Science.gov (United States)

    Kwon, Chang Woo; Park, Kyung-Min; Choi, Seung Jun; Chang, Pahn-Shick

    2015-09-01

    The copper-soap method, which is based on the absorbance of a fatty acid-copper complex at 715 nm, is a widely used colorimetric assay to determine the lipase activity in reversed micellar system. However, the absorbance of the bis(2-ethylhexyl) sodium sulfosuccinate (AOT)-copper complex prevents the use of an AOT/isooctane reversed micellar system. An extraction step was added to the original procedure to remove AOT and eliminate interference from the AOT-copper complex. Among the solvents tested, acetonitrile was determined to be the most suitable because it allows for the generation of a reproducible calibration curve with oleic acid that is independent of the AOT concentrations. Based on the validation data, the modified method, which does not experience interference from the AOT-copper complex, could be a useful method with enhanced accuracy and reproducibility for the lipase assay.

  17. FT-IR studies on the conformation and effective head-group area of AOT molecules in W/O microemulsions

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Using Fourier transform infrared(FT-IR) spectroscopy technique, the carbonyl stretching vibration bands of AOT in sodium bis(2-ethylhexyl)sulfosuccinate(AOT)/isooctane/water reverse(W/O) microemulsions system have been investigated by least square curve fitting. The results indicate that an asymmetric adsorbed peak of carbonyl stretching vibration of AOT molecule is situated in(1739 ± 1) and(1725 ± 2) cm-1. The two peaks correspond to different carbonyls in gau-che conformation and trans conformation of AOT molecules, respectively. With different water contents(W0), the variations of peak intensity ratio(Ir1 = I1739/I1725) reflect the change of the ratio for the two conformation populations and the variations of the effective head-group area of AOT mo-lecule have relations to the ratio of two conformation populations.

  18. Stabilization of α-amylase by using anionic surfactant during the immobilization process

    Science.gov (United States)

    El-Batal, A. I.; Atia, K. S.; Eid, M.

    2005-10-01

    This work describes the entrapment of α-amylase into butylacrylate-acrylic acid copolymer (BuA/AAc) using γ irradiation. The effect of an anionic surfactant (AOT), the reuse efficiency, and kinetic behavior of immobilized α-amylase were studied. Covering of α-amylase with bis-(2-ethylhexyl)sulfosuccinate sodium salt (AOT) made the enzyme more stable than the uncovered form. The hydrolytic activity of the pre-coated immobilized α-amylase was increased below the critical micelle concentration (cmc) (10 mmol/L). The results showed an increase in the relative activity with increase in the degree of hydration. The pre-coated immobilized α-amylase showed a higher k/K and lower activation energy compared to the free and uncoated-immobilized preparation, respectively. The results suggest that the immobilization of α-amylase is a potentially useful approach for commercial starch hydrolysis in two-phase systems.

  19. Precipitation of Zinc Oxide Nanoparticles in Bicontinuous Microemulsions

    Directory of Open Access Journals (Sweden)

    Liliana E. Romo

    2011-01-01

    Full Text Available Zinc oxide nanoparticles were obtained directly, avoiding the calcination step, by precipitation at 70°C in bicontinuous microemulsions stabilized with a mixture of surfactants sodium bis (2-ethylhexyl sulfosuccinate/sodium dodecyl sulfate (2/1, wt./wt. containing 0.7 M zinc nitrate aqueous solution. Two concentrations of aqueous solution of precipitating agent sodium hydroxide were used under different dosing times on microemulsion. Characterization by X-ray diffraction and electron microscopy allowed us to identify particles with an acicular rod-like morphology and a hexagonal wurtzite crystal structure as small as 8.5 and 30 nm in average diameter and length, respectively. Productivities much higher than those typical in the preparation of zinc oxide nanoparticles via reverse microemulsions were obtained. Particle size was the same at the two studied sodium hydroxide concentrations, while it increases as dosing time of the precipitant agent increases. It is believed that the surfactant film on the microemulsion channels restricts the particle diameter growth.

  20. Silver nanoparticles of variable morphology synthesized in aqueous foams as novel templates

    Indian Academy of Sciences (India)

    Saikat Mandal; Sujatha K Arumugam; Renu Pasricha; Murali Sastry

    2005-08-01

    In this paper, we describe the synthesis of silver nanocrystals within aqueous foams as a template. More specifically, we show that aqueous Ag+ ions may be electrostatically complexed with the anionic surfactants aerosol OT (sodium bis-2-ethylhexyl-sulfosuccinate, (AOT) and sodium dodecyl sulphate (SDS)) in a highly stable liquid foam. After drainage of the foam, the silver ions are reduced in situ by introducing sodium borohydride into the foam by capillary flow. This leads to the formation of silver nanoparticles of spherical, tape- and sheet-like morphology in the foam. The structure of the foam is extremely complex and presents reaction sites of different spatial extent. The differences in foam reaction–site geometry are believed to be responsible for the morphology variation in the silver nanoparticles observed. The silver nanoparticles are observed to be extremely stable in solution suggesting that the AOT or SDS molecules stabilize them. This approach appears promising for application in large-scale synthesis of nanoparticles and may be readily extended to other chemical compositions.

  1. Preparation of Silver Nanostructures from Bicontinuous Microemulsions

    Directory of Open Access Journals (Sweden)

    M. A. Pedroza-Toscano

    2012-01-01

    Full Text Available Precipitation of silver nanoparticles at 70°C was carried out by dosing a 1.3 M sodium borohydride aqueous solution over bicontinuous microemulsions formed with a mixture of sodium bis(2-ethylhexyl sulfosuccinate (AOT and sodium dodecylsulfate (SDS as surfactants, a 0.5 M silver nitrate aqueous solution, and toluene. Weight ratios of 2.5/1 and 3/1 AOT/SDS were used in the precipitation reactions. Silver nanoparticles were characterized by transmission electronic microscopy, X-ray diffraction, and atomic absorption spectroscopy. A mixture of isolated spheroidal nanoparticles (≈15 wt.% with an average diameter around 10 nm and wormlike structures (≈85 wt.% with an average length close to 480 nm and an average diameter ca. 40 nm was obtained, regardless of the AOT/SDS ratio. Higher yields were obtained compared with those reported when reverse microemulsions were employed. Formation of wormlike structures was ascribed to one-dimensional aggregation of crystal and particles within the channels of bicontinuous microemulsions, which performed as templates.

  2. Determination of water states and the structural parameters of W/O microemulsions

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The states of water in sodium bis(2-ethylhexyl) sulfosuccinate (AOT)/isooctane/water reverse(W/O) microemulsions system have been investigated by using Fourier transform infrared spectroscopy(FT-IR) technique. The broad peak obtained for hydroxy(O-H) of water has been resolved by least square curve-fitting. It has been observed that the water solubilized in microemulsion droplets has four states, i.e. bound water with sulfo-group, free water, bound water with sodium counterion in the water pool of microemulsion droplets and a small amount of trapped water in the palisade layer of microemulsion droplets. The following have also been determined: the aggregation number (n), the radius of the water pool in the microemulsions(rw), the thickness of the bound water with sulfo-group(d1), the thickness of the bound water with sodium counterion(d2), the total thickness of the bound water ( d ) and the effective area of head groups of AOT(AAOT).

  3. High-Yield Synthesis of Silver Nanoparticles by Precipitation in a High-Aqueous Phase Content Reverse Microemulsion

    Directory of Open Access Journals (Sweden)

    Y. D. Sosa

    2010-01-01

    Full Text Available Silver nanoparticles were precipitated at 70°C in a reverse microemulsion containing a high concentration of 0.5 M silver nitrate aqueous solution, toluene as organic phase, and a mixture of surfactants sodium bis (2-ethylhexyl sulfosuccinate/sodium dodecyl sulfate (2/1, w/w. Nanoparticles were characterized by X-ray diffraction, atomic absorption spectroscopy, and high-resolution transmission electron microscopy. In spite of the high-water/surfactant molar ratio and concentration of silver nitrate solution used in this study, characterizations demonstrated that nanoparticles were silver crystals (purity >99% with 8.6–8.8 nm in average diameter and 2.9–4.7 nm in standard deviation. It is proposed that slow dosing rate of aqueous solution of precipitating agent and the small molecular volume of toluene attenuated both particle aggregation and polydispersity widening. Experimental yield of silver nanoparticles obtained in this study was much higher than theoretical yields calculated from available data in the literature on preparation of silver nanoparticles in reverse microemulsions.

  4. Organo-gel de heptano: diagrama de fases e aplicações sintéticas

    Directory of Open Access Journals (Sweden)

    Queiroz Neide

    1999-01-01

    Full Text Available The phase diagram formation of microemulsion-based gels composed of an anionic surfactant aerosol-OT sodium bis (2-ethylhexyl-sulphosuccinate, water, gelatin and an organic solvent is presented for heptane. The stability of this organo- gel, when an enzyme is immobilized is discussed in terms of its reutilization in various esters synthesis.

  5. Organo-gel de heptano: diagrama de fases e aplicações sintéticas

    OpenAIRE

    Queiroz Neide; Nascimento

    1999-01-01

    The phase diagram formation of microemulsion-based gels composed of an anionic surfactant aerosol-OT sodium bis (2-ethylhexyl)-sulphosuccinate), water, gelatin and an organic solvent is presented for heptane. The stability of this organo- gel, when an enzyme is immobilized is discussed in terms of its reutilization in various esters synthesis.

  6. Molecular Dynamics Simulations of Cytochrome c un-folding in AOT Reverse Micelles: the first steps

    CERN Document Server

    Abel, Stéphane; Marchi, Massimo

    2009-01-01

    This paper explores the reduced form of horse cytochrome c confined in reverse micelles (RM) of so-dium bis-(2-ethylhexyl) sulfosuccinate (AOT) in isooctane by molecular dynamics simulation. RMs of two sizes were constructed at a water content of Wo = [H2O]/[AOT] = 5.5 and 9.1. Our results show that the protein secondary structure and the heme conformation both depend on micellar hydration. At low hydration, the protein structure and the heme moiety remain stable, whereas at high water content the protein becomes unstable and starts to unfold. At Wo = 9.1, according to the X-ray structure, conforma-tional changes are mainly localized on protein loops and around the heme moiety, where we observe a partial opening of the heme crevice. These findings suggest that within our time window (10 ns), the structural changes observed at the heme level are the first steps of the protein denaturation process, pre-viously described experimentally in micellar solutions. In addition, a specific binding of AOT molecules to a ...

  7. Enzyme-Catalyzed Regioselective Modification of Starch Nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Chakraborty, Soma [Polytechnic Univ., Brooklyn, NY (United States). National Science Foundation (NSF) Center for Biocatalysis and Bioprocessing of Macromolecules, Othmer Dept. of Chemical and Biological Science and Engineering; Sahoo, Bishwabhusan [Polytechnic Univ., Brooklyn, NY (United States). National Science Foundation (NSF) Center for Biocatalysis and Bioprocessing of Macromolecules, Othmer Dept. of Chemical and Biological Science and Engineering; Teraoka, Iwao [Polytechnic Univ., Brooklyn, NY (United States). National Science Foundation (NSF) Center for Biocatalysis and Bioprocessing of Macromolecules, Othmer Dept. of Chemical and Biological Science and Engineering; Miller, Lisa M. [Brookhaven National Lab. (BNL), Upton, NY (United States). National Synchrotron Light Source (NSLS); Gross, Richard A. [Polytechnic Univ., Brooklyn, NY (United States). National Science Foundation (NSF) Center for Biocatalysis and Bioprocessing of Macromolecules, Othmer Dept. of Chemical and Biological Science and Engineering

    2004-12-13

    The selective esterification of starch nanoparticles was performed using as catalyst Candida antartica Lipase B (CAL-B) in its immobilized (Novozym 435) and free (SP-525) forms. The starch nanoparticles were made accessible for acylation reactions by formation of Aerosol-OT (AOT, bis(2-ethylhexyl)sodium sulfosuccinate) stabilized microemulsions. Starch nanoparticles in microemulsions were reacted with vinyl stearate, ε-caprolactone, and maleic anhydride at 40 °C for 48 h to give starch esters with degrees of substitution (DS) of 0.8, 0.6, and 0.4, respectively. Substitution occurred regioselectively at the C-6 position of the glucose repeat units. Infrared microspectroscopy (IRMS) revealed that AOT-coated starch nanoparticles diffuse into the outer 50 μm shell of catalyst beads. Thus, even though CAL-B is immobilized within a macroporous resin, CAL-B is sufficiently accessible to the starch nanoparticles. When free CAL-B was incorporated along with starch within AOT-coated reversed micelles, CAL-B was also active and catalyzed the acylation with vinyl stearate (24 h, 40 °C) to give DS = 0.5. After removal of surfactant from the modified starch nanoparticles, they were dispersed in DMSO or water and were shown to retain their nanodimensions.

  8. The forward and backward transport processes in the AOT/hexane reversed micellar extraction of soybean protein.

    Science.gov (United States)

    Chen, Jun; Chen, Fengliang; Wang, Xianchang; Zhao, Xiaoyan; Ao, Qiang

    2014-10-01

    Soybean protein was taken as a model protein to investigate two aspects of the protein extraction by sodium bis(2-ethylhexyl) sulfosuccinate (AOT) reverse micelles: (1) the forward protein extraction from the solid state, and the effect of pH, AOT concentration, alcohol and water content (W0) on the transfer efficiency; (2) the back-transfer, the capability of the protein to be recovered from the micellar solution. The experimental results led to the conclusion that the highest forward extraction efficiency of soybean protein was reached at AOT concentration 180 mmol l(-1), aqueous pH 7.0, KCl concentration 0.05 mol l(-1), 0.5 % (v/v) alcohol, W0 18. Under these conditions, the forward extraction efficiency of soybean protein achieved 70.1 %. It was noted that the percentage of protein back extraction depended on the salt concentration and pH value. Around 92 % of protein recovery was obtained after back extraction.

  9. Kinetic Studies on the Lignin Peroxidase Catalyzed Oxidation of Veratryl Alcohol by H2O2 in AOT/Isooctane/Toluene/Water Reverse Micelles

    Institute of Scientific and Technical Information of China (English)

    LIU Jin-Ting; HUANG Xi-Rong; GAO Pei-ji

    2007-01-01

    The steady state kinetics of the lignin peroxidase (LIP) catalyzed oxidation of veratryl alcohol (VA) by H2O2 in a sodium bis(2-ethylhexyl) sulfosuccinate (AOT)/isooctane/toluene/water reverse micellar medium was studied and a comparison with the corresponding aqueous medium was made to understand the effect of the reverse micellar medium on the catalytic mechanism and kinetic parameters. Results indicated that the model reaction in the AOT medium were the same as those in bulk aqueous medium, but the kinetic parameters except Km,H2O2 were greatly different in the two media. The kcat and Ki values in the reverse micelle were approximately 2 and 20 times smaller than the corresponding values in the aqueous solution, but the Michaelis constant of VA was approximately 100times greater than that in the aqueous solution. The above mentioned differences in the kinetic parameters were caused by the microheterogeneity and the interface of the AOT reverse micelle, which resulted in the partitioning of VA and H2O2, and by the changes of the conformation of LiP and the reactivity of the substrates.

  10. Phase and sedimentation behavior of oil (octane) dispersions in the presence of model mineral aggregates.

    Science.gov (United States)

    Gupta, Anju; Sender, Maximilian; Fields, Sarah; Bothun, Geoffrey D

    2014-10-15

    Adsorption of suspended particles to the interface of surfactant-dispersed oil droplets can alter emulsion phase and sedimentation behavior. This work examines the effects of model mineral aggregates (silica nanoparticle aggregates or SNAs) on the behavior of oil (octane)-water emulsions prepared using sodium bis(2-ethylhexyl) sulfosuccinate (DOSS). Experiments were conducted at different SNA hydrophobicities in deionized and synthetic seawater (SSW), and at 0.5mM and 2.5mM DOSS. SNAs were characterized by thermogravimetric analysis (TGA) and dynamic light scattering (DLS), and the emulsions were examined by optical and cryogenic scanning electron microscopy. In deionized water, oil-in-water emulsions were formed with DOSS and the SNAs did not adhere to the droplets or alter emulsion behavior. In SSW, water-in-oil emulsions were formed with DOSS and SNA-DOSS binding through cation bridging led to phase inversion to oil-in-water emulsions. Droplet oil-mineral aggregates (OMAs) were observed for hydrophilic SNAs, while hydrophobic SNAs yielded quickly sedimenting agglomerated OMAs.

  11. How Anionic Vesicles Steer the Oligomerization of Enzymatically Oxidized p-Aminodiphenylamine (PADPA) toward a Polyaniline Emeraldine Salt (PANI-ES)-Type Product.

    Science.gov (United States)

    Luginbühl, Sandra; Bertschi, Louis; Willeke, Martin; Schuler, Lukas D; Walde, Peter

    2016-09-27

    The oxidation of the aniline dimer, p-aminodiphenylamine (PADPA), with Trametes versicolor laccase and O2 in an aqueous solution of pH 3.5 is controlled by negatively charged AOT (sodium bis(2-ethylhexyl) sulfosuccinate) vesicles. With vesicles, a product resembling polyaniline in its emeraldine salt form (PANI-ES) is obtained, in contrast to the reaction without vesicles where no such product is formed. To understand this observation, the product distribution and structures from the reaction with and without vesicles were determined by using partially selectively deuterated PADPA as a starting material and analyzing the products with HPLC-MS. We found that in the presence of vesicles the main product is obtained in about 50% yield, which is the N-C-para-coupled PADPA dimer that has spectroscopic properties of PANI-ES, as determined by time-dependent density functional theory (TD-DFT) calculations. A secondary reaction route leads to longer PADPA oligomers that must contain a phenazine core. Without vesicles, PADPA and its products undergo partial hydrolysis, but in the presence of vesicles, hydrolysis does not occur. Because molecular dynamics (MD) simulations show that the main intermediate oxidation product is embedded within the vesicle membrane, where the water content is very low, we propose that the microenvironment of the vesicle membrane protects the oxidation products from unwanted hydrolysis.

  12. Selective production of 1-monocaprin by porcine liver carboxylesterase-catalyzed esterification: Its enzyme kinetics and catalytic performance.

    Science.gov (United States)

    Park, Kyung-Min; Lee, Jong-Hyuk; Hong, Sung-Chul; Kwon, Chang Woo; Jo, Minje; Choi, Seung Jun; Kim, Keesung; Chang, Pahn-Shick

    2016-01-01

    Porcine liver carboxylesterase (PLE) belongs to carboxylesterase family (EC 3.1.1.1) as a serine-type esterase. The PLE-catalyzed esterification of capric acid with glycerol in reverse micelles was investigated on the catalytic performance and enzyme kinetics. The most suitable structure of reverse micelles was comprised of isooctane (reaction medium) and bis(2-ethylhexyl) sodium sulfosuccinate (AOT, anionic surfactant) with 0.1 of R-value ([water]/[surfactant]) and 3.0 of G/F-value ([glycerol]/[fatty acid]) for the PLE-catalyzed esterification. In the aspect of regio-selectivity, the PLE mainly produced 1-monocaprin without any other products (di- and/or tricaprins of subsequent reactions). Furthermore, the degree of esterification at equilibrium state (after 4 h from the initiation) was 62.7% under the optimum conditions at pH 7.0 and 60 °C. Based on Hanes-Woolf plot, the apparent Km and Vmax values were calculated to be 16.44 mM and 38.91 μM/min/mg protein, respectively.

  13. Ultrafast dynamics of solvation and charge transfer in a DNA-based biomaterial.

    Science.gov (United States)

    Choudhury, Susobhan; Batabyal, Subrata; Mondol, Tanumoy; Sao, Dilip; Lemmens, Peter; Pal, Samir Kumar

    2014-05-01

    Charge migration along DNA molecules is a key factor for DNA-based devices in optoelectronics and biotechnology. The association of a significant amount of water molecules in DNA-based materials for the intactness of the DNA structure and their dynamic role in the charge-transfer (CT) dynamics is less documented in contemporary literature. In the present study, we have used a genomic DNA-cetyltrimethyl ammonium chloride (CTMA) complex, a technological important biomaterial, and Hoechest 33258 (H258), a well-known DNA minor groove binder, as fluorogenic probe for the dynamic solvation studies. The CT dynamics of CdSe/ZnS quantum dots (QDs; 5.2 nm) embedded in the as-prepared and swollen biomaterial have also been studied and correlated with that of the timescale of solvation. We have extended our studies on the temperature-dependent CT dynamics of QDs in a nanoenvironment of an anionic, sodium bis(2-ethylhexyl)sulfosuccinate reverse micelle (AOT RMs), whereby the number of water molecules and their dynamics can be tuned in a controlled manner. A direct correlation of the dynamics of solvation and that of the CT in the nanoenvironments clearly suggests that the hydration barrier within the Arrhenius framework essentially dictates the charge-transfer dynamics.

  14. Biocatalytic Synthesis of Flavor Ester “Pentyl Valerate” Using Candida rugosa Lipase Immobilized in Microemulsion Based Organogels: Effect of Parameters and Reusability

    Science.gov (United States)

    Raghavendra, Tripti; Panchal, Nilam; Divecha, Jyoti; Shah, Amita; Madamwar, Datta

    2014-01-01

    Pentyl valerate was synthesized biocatalytically using Candida rugosa lipase (CRL) immobilized in microemulsion based organogels (MBGs). The optimum conditions were found to be pH 7.0, temperature of 37°C, ratio of concentration of water to surfactant (Wo) of 60, and the surfactant sodium bis-2-(ethylhexyl)sulfosuccinate (AOT) for MBG preparation. Although kinetic studies revealed that the enzyme in free form had high affinity towards substrates (Km = 23.2 mM for pentanol and 76.92 mM for valeric acid) whereas, after immobilization, the Km values increased considerably (74.07 mM for pentanol and 83.3 mM for valeric acid) resulting in a slower reaction rate, the maximum conversion was much higher in case of immobilized enzyme (~99%) as compared to free enzyme (~19%). Simultaneous effects of important parameters were studied using response surface methodology (RSM) conjugated with Box-Behnken design (BBD) with five variables (process parameters), namely, enzyme concentration, initial water content (Wo), solvent used for MBG preparation, substrate ratio and time, and response as the final product formation, that is, pentyl valerate (%). The MBGs were reused for 10 consecutive cycles for ester synthesis. Efficacy of AOT/isooctane as dehydrating agent for extracting excess water from MBGs was found to exert a positive effect on the esterification reaction. PMID:25093166

  15. Impact of a surfactant on the electroactivity of proteins at an aqueous-organogel microinterface array.

    Science.gov (United States)

    O'Sullivan, Shane; Arrigan, Damien W M

    2013-02-05

    The impact of surfactant addition to the organic phase on the electroactivity of proteins at the aqueous-organogel interface was examined by voltammetry. The presence of bis(2-ethylhexyl)sulfosuccinate (AOT) in the organogel phase, as the sodium salt, caused marked changes in the peak currents for myoglobin detection. The protein desorption voltammetric peak exhibited a 6-fold increase in the current compared to the corresponding experiment without surfactant. Interfacial coverage showed a 17-fold increase in the adsorbed protein at the interface, from 50 pmol cm(-2), in the absence of surfactant, to 850 pmol cm(-2), in the presence of 10 mM surfactant. Additionally, the presence of the surfactant resulted in a second pair of adsorption/desorption peaks at lower potentials and in a change in the capacitance of the system. The formation of surfactant-protein and surfactant-protein-organic anion deposits is proposed on the basis of these features, leading to increased voltammetric signals for myoglobin, hemoglobin, and cytochrome c. The mechanism of protein-surfactant interaction was probed by using the surfactant as the anion in the organic phase electrolyte salt. Repetitive cyclic voltammetry of cytochrome c showed that in the presence of surfactant there was an enhancement of the signal, caused by a buildup of the protein-surfactant-electrolyte anion assembly at the interface. These findings provide the basis for surfactant-modified interfaces to enhance the electroanalytical performance for protein detection.

  16. Kinetics and mechanism of the cutinase-catalyzed transesterification of oils in AOT reversed micellar system.

    Science.gov (United States)

    Badenes, Sara M; Lemos, Francisco; Cabral, Joaquim M S

    2011-11-01

    The kinetics of the enzymatic transesterification between a mixture of triglycerides (oils) and methanol for biodiesel production in a bis(2-ethylhexyl) sodium sulfosuccinate (AOT)/isooctane reversed micellar system, using recombinant cutinase from Fusarium solani pisi as a catalyst, was investigated. In order to describe the results that were obtained, a mechanistic scheme was proposed, based on the literature and on the experimental data. This scheme includes the following reaction steps: the formation of the active enzyme-substrate complex, the addition of an alcohol molecule to the complex followed by the separation of a molecule of the fatty acid alkyl ester and a glycerol moiety, and release of the active enzyme. Enzyme inhibition and deactivation effects due to methanol and glycerol were incorporated in the model. This kinetic model was fitted to the concentration profiles of the fatty acid methyl esters (the components of biodiesel), tri-, di- and monoglycerides, obtained for a 24 h transesterification reaction performed in a stirred batch reactor under different reaction conditions of enzyme and initial substrates concentration.

  17. On the composition fluctuations of reverse micelles.

    Science.gov (United States)

    Tovstun, Sergey A; Razumov, Vladimir F

    2010-11-15

    The polydispersity of the reverse micelles is determined mainly by the fluctuations of their composition. The composition of the reverse micelle is a two-dimensional random variable whose components are the numbers of water (i) and surfactant (j) molecules. In this study the fluctuations of the composition of the reverse micelles are considered in the Gaussian approximation. It is shown that the standard deviation of the quantity w=i/j may be calculated from the dependence of the water vapor pressure above the microemulsion on the molar ratio W=[water]/[surfactant]. The estimation based on the literature data for microemulsion system sodium bis(2-ethylhexyl)sulfosuccinate/water/isooctane at 37°C in the range W=0-18 has shown that the relative standard deviation of the quantity w is about 10%. It is shown that the value of the composition fluctuations is related to the dependence of average composition on the concentration of reverse micelles at constant parameter W.

  18. Synthesis of single-walled carbon nanotube networks using monodisperse metallic nanocatalysts encapsulated in reverse micelles

    Directory of Open Access Journals (Sweden)

    Gayduchenko Igor A.

    2016-01-01

    Full Text Available We report on a method of synthesis of single-walled carbon nanotubes percolated networks on silicon dioxide substrates using monodisperse Co and Ni catalyst. The catalytic nanoparticles were obtained by modified method of reverse micelles of bis-(2-ethylhexyl sulfosuccinate sodium in isooctane solution that provides the nanoparticle size control in range of 1 to 5 nm. The metallic nanoparticles of Ni and Co were characterized using transmission electron microscopy (TEM and atomic-force microscopy (AFM. Carbon nanotubes were synthesized by chemical vapor deposition of CH4/H2 composition at temperature 1000 °С on catalysts pre-deposited on silicon dioxide substrate. Before temperature treatment during the carbon nanotube synthesis most of the catalyst material agglomerates due to magnetic forces while during the nanotube growth disintegrates into the separate nanoparticles with narrow diameter distribution. The formed nanotube networks were characterized using AFM, scanning electron microscopy (SEM and Raman spectroscopy. We find that the nanotubes are mainly single-walled carbon nanotubes with high structural perfection up to 200 μm long with diameters from 1.3 to 1.7 nm consistent with catalyst nanoparticles diameter distribution and independent of its material.

  19. 超声辅助AOT反胶束提取花生蛋白后萃取工艺的优化%Backward Extraction of Peanut Protein through SDS Reverse Micelles Assisted by Ultrasound

    Institute of Scientific and Technical Information of China (English)

    高艳秀; 陈复生; 刘昆仑; 郭珍; 杨颖莹

    2013-01-01

    研究超声辅助AOT(二-(2-乙基己基)瑚珀酸酯磺酸钠)/异辛烷反胶束体系萃取花生蛋白的后萃取过程,并分析各因素对蛋白后萃取率的影响,通过正交试验得到了最佳后萃取工艺条件为:缓冲溶液pH值为8.5、萃取时间为50min、萃取温度为40℃、超声功率240W、KCl浓度为1.5 mol/L,在此条件下,蛋白后萃取率为82.17+1.52%.%The backward of peanut protein was studied by AOT (sodium bis-(2-ethylhexyl) sulfosuccinate)/isooctane reverse micelles system from full-fat peanut powder with sonication. The main factors effecting reverse micelles extraction were analyzed. The orthogonal test design results showed that the optimum conditions of backward extraction were pH 8.5, extraction time 40 min, temperature 40 ℃, ultrasonic power 240 W, and KC1 concentration 1.5 mol/L, under which the extraction rate was 82.17± 1.52%.

  20. Thermostability of Cromobacterium viscosum lipase in AOT/isooctane reverse micelle.

    Science.gov (United States)

    Talukder, M M R; Zaman, M M; Hayashi, Y; Wu, J C; Kawanishi, T

    2007-04-01

    The thermostability of Cromobacterium viscosum lipase (EC 3.1.1.3) entrapped in AOT (sodium bis-[2-ethylhexyl] sulfosuccinate) reverse micelles was increased by the addition of short-chain polyethylene glycol (PEG 400). Two different approaches were considered: (1) the determination of half-life time and (2) the mechanistic analysis of deactivation kinetics. The half-life of lipase entrapped in AOT/isooctane reverse micelles with PEG 400 at 60 degrees C was 28 h, ninefold higher than that in reverse micelles without PEG 400. The lipase entrapped in both reverse micellar systems followed a series-type deactivation mechanism involving two first-order steps. The deactivation constant for the first step at 60 degrees C in PEG containing reverse micelles was 0.055 h!1, 11-fold lower than that in reverse micelles without PEG, whereas it remained almost constant for the second step. The inactivation energy of the lipase entrapped in reverse micelles with and without PEG 400 was 88.12 and 21.97 kJ/mol, respectively.

  1. Time-dependent solubilization of IgG in AOT-brine-isooctane microemulsions: role of cluster formation.

    Science.gov (United States)

    Gerhardt, N I; Dungan, S R

    2002-04-05

    The stability and structure of protein-containing water-in-oil (w/o) microemulsions were investigated by using the large protein immunoglobulin G (IgG, MW 155,000) in a mixture comprised of brine, sulfosuccinic acid bis [2-ethylhexyl]ester (sodium salt), and isooctane. We explored factors affecting the initial uptake of IgG into the w/o microemulsion and its subsequent release to a solid (precipitate) phase, and the kinetics of the latter process. Influences of such parameters as pH, ionic strength, and protein concentration on the solubilization and precipitation of bovine IgG in the organic phase are described. The structure and dynamics in microemulsions containing bovine IgG were probed by using dynamic light scattering, and it was found that the presence of IgG in the microemulsion induced strong attractive forces between the droplets. Based on results obtained by using these various experimental approaches, a model for protein solubilization and release is proposed. In this model, we propose the formation of clusters within which bovine IgG resides and which substantially slow the kinetics of protein release from the droplets to the precipitate phase.

  2. Surface characterization of 7S and 11S globulin powders from soy protein examined by X-ray photoelectron spectroscopy and scanning electron microscopy.

    Science.gov (United States)

    Zhao, Xiaoyan; Chen, Jun; Zhu, Qingjun; Du, Fangling; Ao, Qiang; Liu, Jie

    2011-09-01

    In this study the surface composition of 7S and 11S globulin powders from soybean proteins by aqueous buffer and reverse micelle extractions had been examined using X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). Analysis by XPS revealed that the O and N atomic percentage of 7S and 11S globulin surfaces from bis(2-ethylhexyl) sodium sulfosuccinate (AOT) reverse micelle was higher than from aqueous buffer, but the C atomic percentage was lower. The O/C ratio of the 7S globulin powder from aqueous buffer and reverse micelle was similar while significant differences were obtained in the O/C ratio of the 11S globulin powder, N/C atom ratios of the 7S and 11S globulin powders and high-resolution XPS C 1s, N 1s, O 1s spectra. Powder microstructure after reverse micelle treatment showed the presence of small pores, indicating the effect of reverse micelle on the 7S and 11S globulin structure. The obtained results indicated that the reverse micelle could affect the C, O and N components on the surface of soybean proteins. Copyright © 2011 Elsevier B.V. All rights reserved.

  3. Dielectric Spectra of Aerosol OT/Water Systems at Different Concentrations and Temperatures

    Institute of Scientific and Technical Information of China (English)

    ZHAO Kong-shuang; JIA Zhan-jie; YANG Li-kun; XIAO Jin-xin

    2011-01-01

    The dielectric spectra of aerosol OT[AOT,sodium(bis-2-ethylhexyl)sulfosuccinate]/water systems at different concentrations and temperatures were investigated by the dielectric relaxation spectroscopy(DRS).Through the dielectric spectra of different concentrations,two dielectric relaxations were observed over a frequency range from 40 Hz to 110 MHz and the mechanisms of the relaxations were also interpreted based on the Grosse's model.The low-frequency relaxation(around 105 Hz)was attributed to the radial diffusion of counterions along the long-half axis of the rod-like micelle,and the high-frequency relaxation(around 106 Hz)was ascribed to the radial diffusion of counterions along the short-half axis.Furthermore,specific emphasis was placed on studying the effects of temperature on system's conductivity.It was observed that the low-frequency limit of conductivity(k1)decreased and then increased with the increment of temperature under the measured concentration.On the other hand,the conductivity(km and kh)in meso-and high-frequency ranges always increased as temperature increased.Both the tendencies of alteration which mentioned above should be related to the phase transition of AOT/water system.

  4. Room temperature synthesis of rod-like FeC2O4·2H2O and its transition to maghemite, magnetite and hematite nanorods through controlled thermal decomposition

    Science.gov (United States)

    Zhou, Weiwei; Tang, Kaibin; Zeng, Suyuan; Qi, Yunxia

    2008-02-01

    FeC2O4·2H2O nanorods with diameter of about 50 nm and length of up to several micrometers were synthesized at room temperature in a surfactant-assisted system, which was obtained by dissolving bis(2-ethylhexyl)sodium sulfosuccinate (AOT) in a mixed solution composed of water and ethylene glycol (EG). The influence of reaction conditions on the morphology of FeC2O4·2H2O is discussed in detail. Through direct thermal decomposition of FeC2O4·2H2O under different calcination conditions, maghemite (γ-Fe2O3), magnetite (Fe3O4) and hematite (α-Fe2O3) can be selectively obtained, preserving the rod-like morphology. Transmission electron microscope (TEM) and high-resolution transmission electron microscope (HRTEM) characterizations showed that the as-obtained iron oxide nanorods were composed of fine particles with different crystal orientations. The magnetic properties of the as-obtained iron oxide nanorods were systematically investigated.

  5. Probing interactions of neurotransmitters with twin tailed anionic surfactant: A detailed physicochemical study.

    Science.gov (United States)

    Kaur, Rajwinder; Sanan, Reshu; Mahajan, Rakesh Kumar

    2016-05-01

    Keeping in view the role of neurotransmitters (NTs) in central nervous system diseases and in controlling various physiological processes, present study is aimed to study the binding of neurotransmitters (NTs) such as norepinephrine hydrochloride (NE) and serotonin hydrochloride (5-HT) with twin tailed surfactant sodium bis(2-ethylhexyl)sulfosuccinate (AOT). Spectroscopic and electrochemical measurements combined with microcalorimetric measurements were used to characterize the interactions between AOT and NTs. Meteoric modifications to emission profile and absorption spectra of NTs upon addition of AOT are indicative of the binding of NTs with AOT. Distinct interactional states such as formation of ion-pairs, induced and regular micelles with adsorbed NTs molecules have been observed in different concentration regimes of AOT. The formation of ion-pairs from oppositely charged NTs and AOT is confirmed by the reduced absorbance, quenched fluorescence intensity and decrease in peak current (ipa) as well as shifts in peak potential (Epa) values. The stoichiometry and formation of the NTs-AOT complexes has been judged and the extent of interactions is quantitatively discussed in terms of binding constant (K) and free energy of binding (ΔG°). The enthalpy (ΔH°mic) and free energy of micellization (ΔG°mic) for AOT in presence and absence of NTs are determined from the enthalpy curves.

  6. Dynamic light scattering of nano-gels of xanthan gum biopolymer in colloidal dispersion

    Directory of Open Access Journals (Sweden)

    Abbas Rahdar

    2016-09-01

    Full Text Available The dynamical properties of nanogels of xanthan gum (XG with hydrodynamic radius controlled in a size range from 5 nm to 35 nm, were studied at the different XG concentrations in water/sodium bis-2-ethylhexyl-sulfosuccinate (AOT/decane reverse micelles (RMs vs. mass fraction of nano-droplet (MFD at W = 40, using dynamic light scattering (DLS. The diffusion study of nanometer-sized droplets by DLS technique indicated that enhancing concentration of the XG polysaccharide resulted in exchanging the attractive interaction between nano-gels to repulsive interaction, as the mass fraction of nano-droplets increased. The reorientation time (τr of water nanodroplets decreased with MFD for water-in-oil AOT micro-emulsion comprising high concentration (0.0000625 of XG. On the other hand, decreasing concentration of biopolymer led to increasing the rotational correlation time of water nanodroplets with MFD. In conclusion, a single relaxation curve was observed for AOT inverse microemulsions containing different XG concentrations. Furthermore, the interaction between nanogels was changed from attractive to repulsive versus concentration of XG in the AOT RMs.

  7. Solution phase photophysics of 5,7-dimethoxy-2,3,4,9-tetrahydro-1H-carbazol-1-one: Analysing the lineaments of a new fluorosensor to probe different micro-environments

    Energy Technology Data Exchange (ETDEWEB)

    Mitra, Amrit Krishna [Department of Clinical and Experimental Pharmacology, School of Tropical Medicine, Kolkata 700073 (India); Ghosh, Sujay; Sau, Abhishek [Chemical Sciences Division, Saha Institute of Nuclear Physics, Kolkata 700064 (India); Saha, Chandan [Department of Clinical and Experimental Pharmacology, School of Tropical Medicine, Kolkata 700073 (India); Basu, Samita, E-mail: samita.basu@saha.ac.in [Chemical Sciences Division, Saha Institute of Nuclear Physics, Kolkata 700064 (India)

    2015-11-15

    We present here a detailed photophysical study of a newly synthesised fluorophore 5,7-dimethoxy-2,3,4,9-tetrahydro-1H-carbazol-1-one (KTHC-57). Spectroscopic investigation of the compound has been carried out in 14 different protic and aprotic solvents, as well as in different binary solvent mixtures, using absorption, steady-state and time-resolved fluorescence techniques. The spectral behaviour of this compound is found to be extremely sensitive to the polarity and hydrogen bonding nature of the solvent. When considered in micelles, reverse micelles and β-cyclodextrin, KTHC-57 behaves as a reporter of its immediate microenvironment. Extent of hypsochromic shift varies as we move from cationic surfactant cetyltrimethylammonium bromide (~40 nm) to anionic surfactant sodium dodecyl sulphate (~23 nm) to non-ionic surfactant Triton X-100 (~37 nm). In case of anionic reverse micellar nanocavities composed of sodium bis(2-ethylhexyl) sulfosuccinate (AOT)/heptane with increasing water contents, a bathochromic shift of ~50 nm is observed. A quantitative assessment of the emission intensity data on Benesi–Hildebrand equation reveals a 1:1 stoichiometry for KTHC-57:β-CD complex. Triethylamine (TEA) is a simple aliphatic organic molecule that interacts with KTHC-57 in polar aprotic medium. Within β-CD environment, fluorescence quenching takes place along with a bathochromic shift. Interaction of (TEA) with KTHC-57 in β-CD nano-confinement is studied using absorption spectroscopy, steady-state as well as time-resolved fluorescence spectroscopy and laser flash photolysis in conjunction with an external magnetic field. - Highlights: • Excited state properties of KTHC-57 vary with its H-bonding environment. • KTHC-57 interacts differently in various microheterogeneous environments. • Benesi–Hildebrand equation reveals a 1:1 stoichiometry for KTHC-57:β-CD complex. • Organic base TEA quench KTHC-57 fluorescence in polar aprotic solvents. • PET takes place from

  8. Molecular simulation study of water mobility in aerosol-OT reverse micelles.

    Science.gov (United States)

    Chowdhary, Janamejaya; Ladanyi, Branka M

    2011-06-16

    In this work, we present results from molecular dynamics simulations on the single-molecule relaxation of water within reverse micelles (RMs) of different sizes formed by the surfactant aerosol-OT (AOT, sodium bis(2-ethylhexyl)sulfosuccinate) in isooctane. Results are presented for RM water content w(0) = [H(2)O]/[AOT] in the range from 2.0 to 7.5. We show that translational diffusion of water within the RM can, to a good approximation, be decoupled from the translation of the RM through the isooctane solvent. Water translational mobility within the RM is restricted by the water pool dimensions, and thus, the water mean-squared displacements (MSDs) level off in time. Comparison with models of diffusion in confined geometries shows that a version of the Gaussian confinement model with a biexponential decay of correlations provides a good fit to the MSDs, while a model of free diffusion within a sphere agrees less well with simulation results. We find that the local diffusivity is considerably reduced in the interfacial region, especially as w(0) decreases. Molecular orientational relaxation is monitored by examining the behavior of OH and dipole vectors. For both vectors, orientational relaxation slows down close to the interface and as w(0) decreases. For the OH vector, reorientation is strongly affected by the presence of charged species at the RM interface and these effects are especially pronounced for water molecules hydrogen-bonded to surfactant sites that serve as hydrogen-bond acceptors. For the dipole vector, orientational relaxation near the interface slows down more than that for the OH vector due mainly to the influence of ion-dipole interactions with the sodium counterions. We investigate water OH and dipole reorientation mechanisms by studying the w(0) and interfacial shell dependence of orientational time correlations for different Legendre polynomial orders.

  9. Liquid-Liquid Phase Equilibria and Interactions between Droplets in Water-in-Oil Microemulsions.

    Science.gov (United States)

    Yin, Tianxiang; Wang, Mingjie; Tao, Xiaoyi; Shen, Weiguo

    2016-12-20

    The liquid-liquid phase equilibria of [water/sodium bis(2-ethylhexyl)sulfosuccinate (AOT)/n-decane] with the molar ratio w0 of water to AOT being 37.9 and [water/AOT/ethoxylated-2,5,8,11-tetramethyl-6-dodecyne-5,8-diol(Dynol-604)/n-decane] with w0 = 37.9 and the mole fraction α of Dynol-604 in the total surfactants being 0.158 were measured in this study. From the data collected in the critical region, the critical exponent β corresponding to the width of the coexistence curve was determined, which showed good agreement with the 3D-Ising value. A thermodynamic approach based on the Carnahan-Starling-van der Waals type equation was proposed to describe the coexistence curves and to deduce the interaction properties between droplets in the microemulsions. The interaction enthalpies were found to be positive for the studied systems, which evidenced that the entropy effect dominated the phase separations as the temperature increased. The addition of Dynol-604 into the (water/AOT/n-decane) microemulsion resulted in the decrease in the critical temperature and the interaction enthalpy. Combining the liquid-liquid equilibrium data for (water/AOT/n-decane) microemulsions with various w0 values determined previously, it was shown that the interaction enthalpy decreased with w0 and tended to change its sign at low w0, which coincided with the results from the isothermal titration calorimetry investigation. All of these behaviors were interpreted by the effects of entropy and enthalpy and their competition, which resulted from the release of solvent molecules entrapped in the interface of microemulsion droplets and were dependent on the rigidity of the surfactant layers and the size of the droplet.

  10. Insight into the template effect of vesicles on the laccase-catalyzed oligomerization of N-phenyl-1,4-phenylenediamine from Raman spectroscopy and cyclic voltammetry measurements

    Science.gov (United States)

    Ležaić, Aleksandra Janoševic; Luginbühl, Sandra; Bajuk-Bogdanović, Danica; Pašti, Igor; Kissner, Reinhard; Rakvin, Boris; Walde, Peter; Ćirić-Marjanović, Gordana

    2016-08-01

    We report about the first Raman spectroscopy study of a vesicle-assisted enzyme-catalyzed oligomerization reaction. The aniline dimer N-phenyl-1,4-phenylenediamine (= p-aminodiphenylamine, PADPA) was oxidized and oligomerized with Trametes versicolor laccase and dissolved O2 in the presence of sodium bis(2-ethylhexyl)sulfosuccinate (AOT) vesicles (80-100 nm diameter) as templates. The conversion of PADPA into oligomeric products, poly(PADPA), was monitored during the reaction by in situ Raman spectroscopy. The results obtained are compared with UV/vis/NIR and EPR measurements. All three complementary methods indicate that at least some of the poly(PADPA) products, formed in the presence of AOT vesicles, resemble the conductive emeraldine salt form of polyaniline (PANI-ES). The Raman measurements also show that structural units different from those of “ordinary” PANI-ES are present too. Without vesicles PANI-ES-like products are not obtained. For the first time, the as-prepared stable poly(PADPA)-AOT vesicle suspension was used directly to coat electrodes (without product isolation) for investigating redox activities of poly(PADPA) by cyclic voltammetry (CV). CV showed that poly(PADPA) produced with vesicles is redox active not only at pH 1.1-as expected for PANI-ES-but also at pH 6.0, unlike PANI-ES and poly(PADPA) synthesized without vesicles. This extended pH range of the redox activity of poly(PADPA) is important for applications.

  11. Effect of the addition of a nonaqueous polar solvent (glycerol) on enzymatic catalysis in reverse micelles. Hydrolysis of 2-naphthyl acetate by alpha-chymotrypsin.

    Science.gov (United States)

    Falcone, R Darío; Biasutti, M Alicia; Correa, N Mariano; Silber, Juana J; Lissi, Eduardo; Abuin, Elsa

    2004-07-06

    The kinetics of hydrolysis of 2-naphthyl acetate (2-NA) catalyzed by alpha-chymotrypsin (alpha-CT), in reverse micellar solutions formed by glycerol (GY)-water (38% v/v) mixture/sodium bis(2-ethylhexyl)sulfosuccinate (AOT)/n-heptane has been determined by spectroscopic measurements. To compare the efficiency of this reaction with that observed in micelles with water in the core, as well as in the corresponding homogeneous media, the reaction was also studied in water/AOT/n-heptane reverse micellar solutions and in both homogeneous media (water and GY-water, 38% v/v mixture). In every media, alpha-CT was characterized by the absorption and emission spectra, the fluorescence lifetimes, and the fluorescence anisotropy of its tryptophan residues. The effect of AOT concentration on the kinetic parameters obtained in the micellar systems was determined, at a constant molar ratio of the inner polar solvent and surfactant. Moreover, the data obtained allowed the evaluation of the 2-NA partition constant between the organic and the micellar pseudophase. It is shown that the addition of GY to the micelle interior results in an increase in the catalytic properties of alpha-CT. The fluorescence anisotropy studies in the different media show that the addition of GY increases the viscosity as compared with the aqueous systems. It seems that the GY addition to the reverse micellar aggregates results in a decrease of the conformational mobility of alpha-CT, which leads to an increase of the enzyme stability and activity.

  12. REVERSE MICROEMULSION OF IGEPAL Co-720 SYSTEM AS MICROREACTOR FOR CdS SYNTHESIS

    Directory of Open Access Journals (Sweden)

    Fitria Rahmawati

    2016-08-01

    Full Text Available A Research on CdS synthesis in reverse microemulsion of Igepal CO-720 system has been conducted at various weight ratio of water to surfactant. Igepal CO-720 naturally forms oil in water (o/w emulsion type due to its high HLB (Hydrophilic -Lipophilic Balance value. Therefore, in this research the Igepal CO-720 system was inversed into water in oil (w/o system before it was used as microreactor for CdS synthesis. As comparison, a system of AOT (Aerosol OT; sodium bis (2-ethylhexyl sulfosuccinate which is naturally w/o system was also used as microreactor for CdS synthesis. The prepared CdS was analyzed by X-ray diffraction for crystal identification, scanning electron microscope for morphological analysis, UV-Vis for absorption edge determination and photoelectrochemical testing for photoactivity. The results show that the Igepal CO -720 system can be inverted into w/o system and can be used as microreactor for CdS synthesis. The prepared CdS is in nanosize with the average diameter of 2.517 ± 0.014 nm and the average gap energy of 3.805 ± 0.178 eV. The prepared CdS in Igepal CO-720 system has less regular form in comparison with morphology of the prepared CdS in AOT system. As the ω values decreases the particle diameter decreases, the gap energy increases and the % IPCE increases. It indicates that high surfactant concentration allows small size micelles formation and produced smaller CdS particle that has high surface area and therefore provide higher photocatalytic activity which was indicated by high value of its % IPCE.

  13. Structural and dynamical transformations between neighboring dense microemulsion phases

    Science.gov (United States)

    Kotlarchyk, M.; Sheu, E. Y.; Capel, M.

    1992-07-01

    A small-angle x-ray scattering (SAXS) study of dense AOT-water-decane microemulsions [AOT denotes sodium bis(2-ethylhexyl) sulfosuccinate] was undertaken in order to delineate clearly the phase behavior and corresponding structural transitions for AOT-plus-water volume fractions ranging from φ=0.60 to 0.95. Spectra were collected for temperatures between T=3 and 65 °C. The resulting T-vs-φ phase diagram indicates three distinct structural domains when the water-to-AOT molar ratio is fixed at W=40.8, namely, the previously investigated L2 droplet phase, a high-temperature Lα lamellar phase, and a low-temperature L3 phase consisting of randomly connected lamellar sheets. A significantly wide coexistence region accompanies the droplet-to-lamellar phase transition, which is demonstrated to be first order. For W between 15 and 40, an analysis of the lamellar structure using a one-dimensional paracrystal model produces a Hosemann g factor indicative of an approximately constant variation in the lamellar spacing of about 8%. The SAXS study was supplemented by dielectric-relaxation, shear-viscosity, and quasielastic light-scattering measurements in order to substantiate the observed phase transitions and further our understanding of the structural and dynamical properties of the L3 phase. It was found that the L3 phase exhibits Newtonian behavior up to a shear rate of 790 s-1, in contradiction to previous theoretical considerations. The phase exhibits two distinct relaxation modes. A relaxation time of ~1 ms characterizes the Brownian motion of a single lamellar sheet, while the motion of the entire interconnected sheet assembly has a relaxation time on the order of 1 s.

  14. EPR study of polyaniline synthesized enzymatically in the presence of submicrometer-sized AOT vesicles.

    Science.gov (United States)

    Rakvin, Boris; Carić, Dejana; Andreis, Mladen; Junker, Katja; Walde, Peter

    2014-02-27

    EPR spectroscopy was used to examine the magnetic properties of two enzymatically synthesized polyaniline (PANI) samples obtained in the presence of submicrometer-sized vesicles formed from sodium bis(2-ethylhexyl)sulfosuccinate (AOT) as templates. PANI-HRPC-AOT was synthesized with horseradish peroxidase isoenzyme C (HRPC) and hydrogen peroxide (H2O2) as oxidant while PANI-TvL-AOT was prepared with Trametes versicolor laccase (TvL) and dioxygen (O2) as oxidant. A commercial conductive sample of the emeraldine salt form of polyaniline (PANI-ES) was also used for comparison in order to correlate the experimental data obtained for PANI-HRPC-AOT and PANI-TvL-AOT with the properties of the well-characterized PANI-ES. It was shown that a model based on the concept of correlated polaronic bands could be applied for the interpretation of the EPR spectra of all three examined samples, although PANI-HRPC-AOT and PANI-TvL-AOT were significantly less conductive than PANI-ES. The magnetic properties of the PANI samples could be related to their conductivities, whereby a low conductivity was ascribed to decreased interchain spin interactions which were detectable from a splitting of the triplet spectrum at low temperatures (5-10 K). The obtained effective distance between the polyaniline chains is larger for enzymatically synthesized PANI than for PANI-ES, most likely mainly due to the presence of AOT which could not be removed completely during the work-up. AOT influences the chain conformation and the average chain-chain distance.

  15. Electron beam induced and microemulsion templated synthesis of CdSe quantum dots: tunable broadband emission and charge carrier recombination dynamics

    Science.gov (United States)

    Guleria, Apurav; Singh, Ajay K.; Rath, Madhab C.; Adhikari, Soumyakanti

    2015-04-01

    CdSe quantum dots (QDs) were synthesized by a rapid and one step templated approach inside the water pool of AOT (sodium bis(2-ethylhexyl) sulfosuccinate) based water-in-oil microemulsions (MEs) via electron beam (EB) irradiation technique with high dose rate, which favours high nucleation rate. The interplay of different experimental parameters such as precursor concentration, absorbed dose and {{W}0} values (aqueous phase to surfactant molar ratio) of MEs were found to have interesting consequences on the morphology, photoluminescence (PL), surface composition and carrier recombination dynamics of as-grown QDs. For instance, highly stable ultrasmall (∼1.7 nm) bluish-white light emitting QDs were obtained with quantum efficiency (η) of ∼9%. Furthermore, QDs were found to exhibit tunable broadband light emission extending from 450 to 750 nm (maximum FWHM ∼180 nm). This could be realized from the CIE (Commission Internationale d’Eclairage) chromaticity co-ordinates, which varied across the blue region to the orange region thereby, conferring their potential application in white light emitting diodes. Additionally, the average PL lifetime ≤ft( ≤ft \\right) values could be varied from 18 ns to as high as 74 ns, which reflect the role of surface states in terms of their density and distribution. Another interesting revelation was the self-assembling of the initially formed QDs into nanorods with high aspect ratios ranging from 7 to 20, in correspondence with the {{W}0} values. Besides, the fundamental roles of the chemical nature of water pool and the interfacial fluidity of AOT MEs in influencing the photophysical properties of QDs were investigated by carrying out a similar study in CTAB (cetyltrimethylammonium bromide; cationic surfactant) based MEs. Surprisingly, very profound and contrasting results were observed wherein ≤ft and η of the QDs in case of CTAB MEs were found to be at least three times lower as compared to that in AOT MEs.

  16. Synthesis of zinc oxide nanoparticles elaborated by microemulsion method

    Energy Technology Data Exchange (ETDEWEB)

    Yildirim, Ozlem Altintas [Department of Metallurgical and Materials Engineering, Middle East Technical University, 06531 Ankara (Turkey); Durucan, Caner, E-mail: cdurucan@metu.edu.t [Department of Metallurgical and Materials Engineering, Middle East Technical University, 06531 Ankara (Turkey)

    2010-09-17

    Graphical abstract: . Display Omitted Research highlights: {yields} Spherical and rod-like ZnO nanostructures obtained in reverse microemulsion. {yields} Morphological variations for microemulsion products with surfactant amount. {yields} Formation mechanism for ZnO nanosructres in a reverse emulsion system. {yields} Optical properties of the ZnO nanoparticles. - Abstract: Zinc oxide (ZnO) nanoparticles were synthesized by a reverse microemulsion system formed from sodium bis(2-ethylhexyl)sulfosuccinate (Aerosol OT, or AOT):glycerol:n-heptane. The zinc precursor was zinc acetate dihydrate. The formation of ZnO nanoparticles was achieved by calcination of premature zinc glycerolate microemulsion product in air at 300, 400 and 500 {sup o}C. The crystal structure and the morphology of the ZnO nanoparticles were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Thermal analysis was employed to reveal structural and chemical changes during calcination. Both surfactant concentrations - AOT - in the initial microemulsion formulation and the calcination temperature influenced the morphology and size of the ZnO nanoparticles. Low surfactant concentrations (5:5:90, AOT:glycerol:n-heptane, wt.%) resulted in formation of spherical ZnO nanoparticles. The average particle size increased from 15 {+-} 1 to 24 {+-} 1 nm with calcination temperature, but spherical morphology remained unchanged after all calcination treatments. The microemulsion system containing higher surfactant amount (30:5:65, AOT:glycerol:n-heptane, wt.%) resulted in rod-like ZnO nanostructures after calcination at 300 and 400 {sup o}C, with a diameter of 22 {+-} 3 and 28 {+-} 1 nm; and with a length of 66 {+-} 3 and 72 {+-} 1 nm, respectively. Further increase in the calcination temperature to 500 {sup o}C initiated rod-to-sphere shape transformation for the ZnO nanoparticles produced using this particular microemulsion formulation. For all ZnO microemulsion products, the

  17. Inhibited phenol ionization in reverse micelles: confinement effect at the nanometer scale.

    Science.gov (United States)

    Silva, O Fernando; Fernández, Mariana A; Silber, Juana J; de Rossi, Rita H; Correa, N Mariano

    2012-01-16

    We found that the absorption spectra of 2-acetylphenol (2-HAP), 4-acetylphenol (4-HAP), and p-nitrophenol (p-NPh) in water/sodium 1,4-bis(2-ethylhexyl)sulfosuccinate (AOT)/n-heptane reverse micelles (RMs) at various W(0) (W(0) = [H(2)O]/[surfactant]) values studied changed with time if (-)OH ions were present in the RM water pool. There is an evolution of ionized phenol (phenolate) bands to nonionized phenol absorption bands with time and this process is faster at low W(0) values and with phenols with higher bulk water pK(a) values. That is, in bulk water and at the hydroxide anion concentration used, only phenolate species are observed, whereas in AOT RMs at this fixed hydroxide anion concentration, ionized phenols convert into nonionized phenol species over time. Furthermore, we demonstrate that, independent of the (-)OH concentration used to prepare the AOT RMs, the nonionized phenols are the more stable species in the RM media. We explain our results by considering that strong hydrogen-bonding interactions between phenols and the AOT polar head groups result in the existence of only nonionized phenols at the AOT RM interface. The situation is quite different when the phenols are dissolved in cationic benzyl-n-hexadecyldimethylammonium chloride RMs. Therein, only phenolates species are present at the (-)OH concentrations used. The results clearly demonstrate that the classical definition of pH does not apply in a confined environment, such as in the interior of RMs and challenge the general idea that pH can be determined inside RMs.

  18. Degradation of carbofuran derivatives in restricted water environments: basic hydrolysis in AOT-based microemulsions.

    Science.gov (United States)

    Morales, Jorge; Manso, José A; Cid, Antonio; Lodeiro, Carlos; Mejuto, Juan Carlos

    2012-04-15

    The effect of sodium bis(2-ethylhexyl)sulfosuccinate/isooctane/water microemulsions on the stability of 2,2-dimethyl-2,3-dihydro-1-benzofuran-7-yl methylcarbamate (carbofuran, CF), 3-hydroxy-2,3-dihydro-2,2-dimethylbenzofuran-7-yl methylcarbamate (3-hydroxycarbofuran, HCF) and 3-keto-2,3-dihydro-2,2-dimethylbenzofuran-7-yl methylcarbamate (3-ketocarbofuran, KCF) in basic media has been studied. The presence of these microheterogeneous media implies a large basic hydrolysis of CF and HCF on increasing surfactant concentration and, also, on increasing water content in the microemulsion. The hydrolysis rate constants are approximately 2- and 10-fold higher than those in pure water for HCF and CF, respectively. In contrast, a steep descent in the rate of decomposition for KCF was observed. These behaviours can be ascribed to the presence of CF derivatives both in the hydrophilic phase and in the lipophilic phase, while the hydroxyl ions are only restricted to the water pool of the microemulsion (hydrophilic phase). The kinetic rate constants for the basic hydrolysis in AOT-based microemulsions have been obtained on the basis of a pseudophase model. Taking into account that an important part of soils are colloids, the possibility of the presence of restricted water environments implies that soil composition and its structure will play an important role in the stability of these carbamates. In fact, we observed that the presence of these restricted aqueous media in the environment, in particular in watersheds and in wastewaters, could reduce significantly the half-life of these pesticides (33% and 91% for HCF and CF, respectively).

  19. Insight into the template effect of vesicles on the laccase-catalyzed oligomerization of N-phenyl-1,4-phenylenediamine from Raman spectroscopy and cyclic voltammetry measurements.

    Science.gov (United States)

    Ležaić, Aleksandra Janoševic; Luginbühl, Sandra; Bajuk-Bogdanović, Danica; Pašti, Igor; Kissner, Reinhard; Rakvin, Boris; Walde, Peter; Ćirić-Marjanović, Gordana

    2016-08-26

    We report about the first Raman spectroscopy study of a vesicle-assisted enzyme-catalyzed oligomerization reaction. The aniline dimer N-phenyl-1,4-phenylenediamine (= p-aminodiphenylamine, PADPA) was oxidized and oligomerized with Trametes versicolor laccase and dissolved O2 in the presence of sodium bis(2-ethylhexyl)sulfosuccinate (AOT) vesicles (80-100 nm diameter) as templates. The conversion of PADPA into oligomeric products, poly(PADPA), was monitored during the reaction by in situ Raman spectroscopy. The results obtained are compared with UV/vis/NIR and EPR measurements. All three complementary methods indicate that at least some of the poly(PADPA) products, formed in the presence of AOT vesicles, resemble the conductive emeraldine salt form of polyaniline (PANI-ES). The Raman measurements also show that structural units different from those of "ordinary" PANI-ES are present too. Without vesicles PANI-ES-like products are not obtained. For the first time, the as-prepared stable poly(PADPA)-AOT vesicle suspension was used directly to coat electrodes (without product isolation) for investigating redox activities of poly(PADPA) by cyclic voltammetry (CV). CV showed that poly(PADPA) produced with vesicles is redox active not only at pH 1.1-as expected for PANI-ES-but also at pH 6.0, unlike PANI-ES and poly(PADPA) synthesized without vesicles. This extended pH range of the redox activity of poly(PADPA) is important for applications.

  20. The use of Trametes versicolor laccase for the polymerization of aniline in the presence of vesicles as templates.

    Science.gov (United States)

    Junker, Katja; Kissner, Reinhard; Rakvin, Boris; Guo, Zengwei; Willeke, Martin; Busato, Stephan; Weber, Thomas; Walde, Peter

    2014-02-01

    The enzymatic polymerization of aniline to polyaniline (PANI) with Trametes versicolor laccase (TvL) as catalyst and dioxygen (O₂) as oxidant was investigated in an aqueous medium containing unilamellar vesicles with an average diameter of about 80 nm formed from AOT (=sodium bis(2-ethylhexyl) sulfosuccinate). Compared to the same reaction carried out with horseradish peroxidase isoenzyme C (HRPC) as catalyst and hydrogen peroxide (H₂O₂) as oxidant, notable differences were found in the kinetics of the reaction, as well as in the characteristics of the PANI obtained. Under comparable optimal conditions, which are pH 3.5 for TvL/O₂ and pH 4.3 for HRPC/H₂O₂, the reaction with TvL/O₂ was much slower than with HRPC/H₂O₂, i.e. ≈27 days vs. 1 day reaction time to reach equilibrium with >90% yield at 25 °C. Although in both cases, aniline monomer coupling occurred mainly via the carbon atom in para position of aniline, UV-vis-NIR absorption and EPR measurements indicate that the reaction with TvL/O₂ yielded mainly overoxidized products (with λ(max)=730 nm). These products had a lower amount of unpaired electrons if compared with the products obtained with HRPC/H₂O₂ (with λ(max)≈1000 nm, which is characteristic for the polaron state of PANI-ES, the emeraldine salt form of PANI). Similarly to previous findings with HRPC/H₂O₂, enzyme inactivation occurred during the polymerization also in the case of TvL/O₂. Since the aqueous PANI-vesicle suspensions obtained are of high colloidal stability, they can be used directly as ink in a conventional thermal inkjet printer for printing on paper or on surface treated polyimide films. Printed PANI-ES patterns on paper changed colour from green (emeraldine salt) to blue (emeraldine base) upon exposure to ammonia gas, demonstrating the expected ammonia sensing properties.

  1. Catalytic activity of lignin peroxidase and partition of veratryl alcohol in AOT/isooctane/toluene/water reverse micelles.

    Science.gov (United States)

    Zhang, Wenjuan; Huang, Xirong; Li, Yuezhong; Qu, Yinbo; Gao, Peiji

    2006-04-01

    The activity of lignin peroxidase (LiP) and the partition of its optimum substrate veratryl alcohol (VA) in sodium bis(2-ethylhexyl)sulfosuccinate (AOT)/isooctane/toluene/water reverse micelles were studied in this paper to understand the microheterogeneous effect of the medium on the catalytic properties of LiP hosted in the reverse micelle. Results showed that LiP from Phanerochaete chrysosporium could express its activity in the reverse micelles, but its activity depended, to a great extent, on the composition of the reverse micelles. Optimum activity occurred at a molar ratio of water to AOT (omega0) of 11, a pH value of 3.6, and a volume ratio of isooctane to toluene of 7-9. Under optimum conditions, the half-life of LiP was circa 12 h. The dependence of LiP activity on the volume fraction of water in the medium (theta), at a constant omega0 value of 11, indicated that VA was mainly solubilized in the pseudophase of the reverse micelle. Based on the pseudobiphasic model and the corresponding kinetic method, a linear line can be obtained in a plot of apparent Michaelis constant of VA vs theta, and the partition coefficient of VA between the pseudophase and the organic solvent phase was determined to be 35.8, which was higher than that (22.3) between bulk water and the corresponding mixed organic solvent. H2O2 inhibited LiP at concentrations higher than 80 microM; this concentration value seems to be different from that in aqueous solution (about 3 mM). The differences mentioned above should be ascribed to the microheterogeneity and the interface of the AOT reverse micelle.

  2. Spectrometric study of AOT-hydrolysis reaction in water/AOT/isooctane microemulsions using phenolphthalein as a chemical probe.

    Science.gov (United States)

    Mao, Shiyan; Chen, Zhiyun; Fan, Dashuang; An, Xueqin; Shen, Weiguo

    2012-01-12

    The kinetics of the alkaline hydrolysis of sodium bis(2-ethylhexyl)sulfosuccinate (AOT) in water/AOT/isooctane microemulsions has been studied by monitoring the absorbance change of the phenolphthalein in the system with time. The apparent first-order rate constant k(obs) has been obtained and found to be dependent on both the molar ratio of water to AOT ω and the temperature. The dependences of k(obs) on ω have been analyzed by a pseudophase model which gives the true rate constants k(i) of the AOT-hydrolysis reaction on the interface and the partition coefficients K(wi) for the distribution of OH(-) between aqueous and interface pseudophases at various temperatures; the latter is almost independent of the temperature and ω. The temperature dependences of the reaction rate constants k(obs) and k(i) have been analyzed to obtain enthalpy ΔH(≠), entropy ΔS(≠), and energy E(a) of activation, which indicate that the distribution of OH(-) between aqueous and interface pseudophases increases ΔS(≠) but makes no contribution to E(a) and ΔH(≠). The influence of the overall concentration of AOT in the system on the rate constant has been examined and found to be negligible. It contradicts with what was reported by García-Río et al. (1) but confirms that the first-order reaction of the AOT-hydrolysis takes place on the surfactant interface. The study of the influence of AOT-hydrolysis on the kinetics of the alkaline fading of crystal violet or phenolphthalein in the water/AOT/isooctane microemulsions suggests that corrections for the AOT-hydrolysis in these reactions are required.

  3. Preparation and Characterization of Nanosized Hydroxyapatite Particles in AOT Inverse Microemulsion

    Institute of Scientific and Technical Information of China (English)

    REN Wei; LI Shi-pu; WANG You-fa; CAO Xian-ying; CHEN Xiao-ming

    2004-01-01

    Nanosized particles of hydroxyapatite (HAP) were synthesized by reacting Ca(H2PO4)2*H2O solution complex with equimolar Ca(OH)2 saturated solution in sodium bis(2-ethylhexyl) sulfosuccinate (AOT)/isooctane water-in-oil microemulsion.The formation of microemulsion strongly depended on water content w (w=[H2O]/[AOT] molar ratio) and concentration of surfactant and cosurfactant (1-octanol).By the variety of conductivity with w and the partial ternary phase diagram derived from a series of demarcation points,we set the basic component of microemulsions:[AOT]=0.1M(mol/dm3),[1-octanol]=0.1M and w=3-9.Dynamic light scattering (DLS),UV-visible absorbance,TEM analysis and X-ray diffraction were used to characterize the microemulsion,formation of particles and resulting HAP particles.At low water content(w<9),the water pool radius of the droplet in the Ca(H2PO4)2*H2O microemulsion lineally depended on w.The size of final HAP particles was strongly affected by water content w and reactant concentration.With increasing water content w from 3 to 9,the size of HAP particles increased from 10-20nm to 40-50 nm at reactant concentration [Ca(H2PO4)2*H2O]=12×10-3 mol/dm3.The resulting HAP particles were poorly crystallized and spherical in morphology.

  4. Model study of enhanced oil recovery by flooding with aqueous surfactant solution and comparison with theory.

    Science.gov (United States)

    Fletcher, Paul D I; Savory, Luke D; Woods, Freya; Clarke, Andrew; Howe, Andrew M

    2015-03-17

    With the aim of elucidating the details of enhanced oil recovery by surfactant solution flooding, we have determined the detailed behavior of model systems consisting of a packed column of calcium carbonate particles as the porous rock, n-decane as the trapped oil, and aqueous solutions of the anionic surfactant sodium bis(2-ethylhexyl) sulfosuccinate (AOT). The AOT concentration was varied from zero to above the critical aggregation concentration (cac). The salt content of the aqueous solutions was varied to give systems of widely different, post-cac oil-water interfacial tensions. The systems were characterized in detail by measuring the permeability behavior of the packed columns, the adsorption isotherms of AOT from the water to the oil-water interface and to the water-calcium carbonate interface, and oil-water-calcium carbonate contact angles. Measurements of the percent oil recovery by pumping surfactant solutions into calcium carbonate-packed columns initially filled with oil were analyzed in terms of the characterization results. We show that the measured contact angles as a function of AOT concentration are in reasonable agreement with those calculated from values of the surface energy of the calcium carbonate-air surface plus the measured adsorption isotherms. Surfactant adsorption onto the calcium carbonate-water interface causes depletion of its aqueous-phase concentration, and we derive equations which enable the concentration of nonadsorbed surfactant within the packed column to be estimated from measured parameters. The percent oil recovery as a function of the surfactant concentration is determined solely by the oil-water-calcium carbonate contact angle for nonadsorbed surfactant concentrations less than the cac. For surfactant concentrations greater than the cac, additional oil removal occurs by a combination of solubilization and emulsification plus oil mobilization due to the low oil-water interfacial tension and a pumping pressure increase.

  5. Size and diffusion phenomena of AOT/alcohol/water system in the presence of morin by dynamic light scattering.

    Science.gov (United States)

    Bhattarai, Ajaya; Wilczura-Wachnik, Hanna

    2015-01-30

    Presented paper is a continuation of our studies on morin interaction with AOT (sodium bis(2-ethylhexyl) sulfosuccinate) reversed micelles solutions in two solvents: ethanol and n-decanol. Now we focused on morin influence on size and diffusion phenomena in the system morin/solvent/AOT/water. In this paper precise measurements of dynamic light scattering (DLS) of the effects of temperature, solvents (alcohols), water on the size and diffusion of AOT reversed micelles in the morin/AOT/alcohol/water system are reported. The concentrations of AOT were varied from 0.51 to 0.78mol/L. Morin concentration in during auto-correlation function registration was not the same in each solvent because of its different solubility depending on the solvent. Water concentration in the studied systems was defined by R parameter according to relation: R=(H2O)/(AOT) and was equal 0 and 30 in ethanol, and 0 in n-decanol. DLS measurements were done at 298.15 and 308.15K. DLS experiment involved on detection two relaxation modes (fast and slow) in the systems containing AOT reversed micelles, water, morin and solvents (ethanol and n-decanol). The DLS data clearly show the solvent influence as well as morin presence on AOT reversed micelles size and consequently their diffusion coefficients. Contrary to n-decanol strong competition between morin and ethanol molecules in AOT reversed micelles palisade layer has been found. It suggests that morin molecules replaced ethanol in AOT reversed micelles and locate in their palisade layer strongly increasing AOT reversed micelles size. Furthermore, it was found a sharp increase in correlation radii of slow modes of AOT reversed micelles containing morin molecules and their diffusion coefficients diminishing.

  6. Synthesis, spectroscopic properties and photodynamic activity of two cationic BODIPY derivatives with application in the photoinactivation of microorganisms.

    Science.gov (United States)

    Agazzi, Maximiliano L; Ballatore, M Belén; Reynoso, Eugenia; Quiroga, Ezequiel D; Durantini, Edgardo N

    2017-01-27

    Two cationic BODIPYs 3 and 4 were synthesized by acid-catalyzed condensation of the corresponding pyrrole and benzaldehyde, followed by complexation with boron and methylation. Compound 3 contains methyl at the 1,3,5 and 7 positions of the s-indacene ring and a N,N,N-trimethylamino group attached to the phenylene unit, while 4 is not substituted by methyl groups and the cationic group is bound by an aliphatic spacer. UV-visible absorption spectra of these BODIPYs show an intense band at ∼500 nm in solvents of different polarities and n-heptane/sodium bis(2-ethylhexyl)sulfosuccinate (AOT)/water reverse micelles. Compound 3 exhibits a higher fluorescence quantum yield (ΦF = 0.29) than 4 (ΦF = 0.030) in N,N-dimethylformamide (DMF) due to sterically hindered rotation of the phenylene ring. BODIPYs 3 and 4 induce photosensitized oxidation of 1,3-diphenylisobenzofuran (DPBF) with yields of singlet molecular oxygen of 0.07 and 0.03, respectively. However, the photodynamic activity increases in a microheterogenic medium formed by AOT micelles. Also, both BODIPYs sensitize the photodecomposition of l-tryptophan (Trp). In presence of diazabicyclo[2.2.2]octane (DABCO) or D-mannitol, a reduction in the photooxidation of Trp was found, indicating a contribution of type I photoprocess. Moreover, the addition of KI produces fluorescence quenching of BODIPYs and reduces the photooxidation of DPBF. In contrast, this inorganic salt increases the photoinduced decomposition of Trp, possibly due to the formation of reactive iodine species. The effect of KI was also observed in the potentiation of the photoinactivation of microorganisms. Therefore, the presence of KI could increase the decomposition of biomolecules induced by these BODIPYs in a biological media, leading to a higher cell photoinactivation.

  7. Controlled formation of calcium-phosphate-based hybrid mesocrystals by organic-inorganic co-assembly.

    Science.gov (United States)

    Zhai, Halei; Chu, Xiaobin; Li, Li; Xu, Xurong; Tang, Ruikang

    2010-11-01

    An understanding of controlled formation of biomimetic mesocrystals is of great importance in materials chemistry and engineering. Here we report that organic-inorganic hybrid plates and even mesocrystals can be conveniently synthesized using a one-pot reaction in a mixed system of protein (bovine serum albumin (BSA)), surfactant (sodium bis(2-ethylhexyl) sulfosuccinate (AOT)) and supersaturated calcium phosphate solution. The morphologies of calcium-phosphate-based products are analogous to the general inorganic crystals but they have abnormal and interesting substructures. The hybrids are constructed by the alternate stacking of organic layer (thickness of 1.31 nm) and well-crystallized inorganic mineral layer (thickness of 2.13 nm) at the nanoscale. Their morphologies (spindle, rhomboid and round) and sizes (200 nm-2 μm) can be tuned gradually by changing BSA, AOT and calcium phosphate concentrations. This modulation effect can be explained by a competition between the anisotropic and isotropic assembly of the ultrathin plate-like units. The anisotropic assembly confers mesocrystal characteristics on the hybrids while the round ones are the results of isotropic assembly. However, the basic lamellar organic-inorganic substructure remains unchanged during the hybrid formation, which is a key factor to ensure the self-assembly from molecule to micrometre scale. A morphological ternary diagram of BSA-AOT-calcium phosphate is used to describe this controlled formation process, providing a feasible strategy to prepare the required materials. This study highlights the cooperative effect of macromolecule (frame structure), small biomolecule (binding sites) and mineral phase (main component) on the generation and regulation of biomimetic hybrid mesocrystals.

  8. Sodium Test

    Science.gov (United States)

    ... low levels of cortisol, aldosterone and sex hormones ( Addison disease ) Drinking too much water as might occur during ... urinary sodium levels may indicate diuretic use or Addison disease. Sodium levels are often evaluated in relation to ...

  9. Sodium Phosphate

    Science.gov (United States)

    Sodium phosphate is used in adults 18 years of age or older to empty the colon (large intestine, bowel) ... view of the walls of the colon. Sodium phosphate is in a class of medications called saline ...

  10. Sodium Oxybate

    Science.gov (United States)

    Sodium oxybate is used to prevent attacks of cataplexy (episodes of muscle weakness that begin suddenly and ... urge to sleep during daily activities, and cataplexy). Sodium oxybate is in a class of medications called ...

  11. Sodium and Food Sources

    Science.gov (United States)

    ... Sources Top 10 Sources of Sodium How to Reduce Sodium Sodium Reduction Resources for Everyone Sodium Reduction Fact ... in processed food [PDF-867K] and how to reduce sodium. Sodium Reduction Is Challenging Types of food matter: ...

  12. Sodium in diet

    Science.gov (United States)

    Diet - sodium (salt); Hyponatremia - sodium in diet; Hypernatremia - sodium in diet; Heart failure - sodium in diet ... The body uses sodium to control blood pressure and blood volume. Your body also needs sodium for your muscles and nerves to work ...

  13. Hidden Sodium

    Centers for Disease Control (CDC) Podcasts

    2013-03-04

    In this podcast, learn about reducing sodium intake by knowing what to eat and the main sources of sodium in the diet. It's important for a healthy lifestyle.  Created: 3/4/2013 by National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP).   Date Released: 3/4/2013.

  14. Enhancement of the luminescence efficiency of europium(III) tris(β-diketonato) complex in organic media by quaternary ammonium salts with anionic ligands.

    Science.gov (United States)

    Katano, Hajime; Uematsu, Kohei; Tsukatani, Toshihide

    2011-01-01

    Benzyldimethyltetradecylammonium (BA14(+)) salts with anionic ligands (X(-)), such as bis(2-ethylhexyl)sulfosuccinate, bis(2-ethylhexyl)phosphate (BEHP(-)), and benzotriazole (BTA(-)) anions, were prepared. These salts were soluble in various organic solvents. The luminescence emission spectra of organic solutions of a red luminescent, tris(1,1,1,2,2,3,3-heptafluoro-7,7-dimethyl-4,6-octadionato)europium(III) complex in the presence of the BA14X's were recorded. The emission intensity of the Eu(III) complex was increased remarkably by the addition of BA14X (X(-) = BEHP(-) and BTA(-)). This effect can be attributed to the formation of 1:1 X(-)-adducts of the Eu(III) complex, in which the asymmetry of the ligand field is increased so as to enhance the emission efficiency of the (5)D(0)→(5)F(2) transition. The enhancement effect by BA14X was higher than that of charge-neutral ligands, such as tri-n-octylphosphine oxide and 1,10-phenanthroline, which have been used as second ligands to enhance the emission efficiency of tris(β-diketonato)europium(III) complexes.

  15. Dietary sodium

    DEFF Research Database (Denmark)

    Graudal, Niels

    2015-01-01

    The 2013 Institute of Medicine (IOM) report "Sodium Intake in Populations: Assessment of Evidence" did not support the current recommendations of the IOM and the American Heart Association (AHA) to reduce daily dietary sodium intake to below 2,300 mg. The report concluded that the population...... Control (CDC), other public health advisory bodies, and major medical journals have continued to support the current policy of reducing dietary sodium.......-based health outcome evidence was not sufficient to define a safe upper intake level for sodium. Recent studies have extended this conclusion to show that a sodium intake below 2,300 mg/day is associated with increased mortality. In spite of this increasing body of evidence, the AHA, Centers for Disease...

  16. Interfacial chemistry in solvent extraction systems. Final report for the period June 1, 1994 - May 31, 1998

    Energy Technology Data Exchange (ETDEWEB)

    Neuman, Ronald D.

    2000-03-01

    The interfacial chemistry that occurs in the liquid/liquid extraction of metals ions still remains very incompletely understood at the molecular level. The objective of this comprehensive research program has been to further the fundamental understanding of this complex chemistry by systematically investigating the interfacial behavior of extraction reagents and their interactions with metal ions at both macroscopic (liquid/liquid) and microscopic (reversed micelles) interfaces. Although the importance of the macroscopic interface is well recognized, it is less appreciated that microscopic interfaces, i.e., association microstructure such as reversed micelles, are often present under practical conditions and play a key role in liquid/liquid extraction. An improved knowledge of the interfacial behavior of extractant molecules is of the utmost importance as it relates to the efficacy (extent, selectivity and rate) of the extraction process. During the recent grant period the authors have more intensively investigated the physicochemical nature of metal-extractant aggregates (or microscopic interfaces) in the organic phase of acidic organophosphorus extraction systems from the perspective of colloid and surface science. Since industrial extraction systems are very complex, the authors emphasized the study of the aggregation behavior in model extraction systems of pure metal salts of bis(2-ethylhexyl)phosphoric acid (HDEHP) (e.g., NaDEHP, Ni(DEHP){sub 2} CO(DEHP){sub 2}) or bis(2-ethylhexyl) sulfosuccinate, whose sodium salt (AOT) is the classical surfactant used often in studies of the structure and properties of reversed micelles, to eliminate any possible uncertainty in the metal-extractant complex composition. This approach evolved into a new initiative that utilized molecular modeling in order to clarify the molecular structure of metal-extractant micellar aggregates for which information is very difficult to obtain from direct experimental measurements

  17. Sodium - blood

    Science.gov (United States)

    ... gland problems such as Cushing syndrome or hyperaldosteronism Diabetes insipidus (type of diabetes in which kidneys are not able to conserve water) Too much salt or sodium bicarbonate in the diet Use of certain medicines, including corticosteroids, laxatives, lithium, ...

  18. Solvation dynamics of coumarin 153 embedded in AOT + phenol organogels studied by time-resolved fluorescence spectroscopy

    Science.gov (United States)

    Nishiyama, Katsura; Takata, Kei; Watanabe, Keiichi; Shigematsu, Hirotake

    2012-03-01

    We investigate solvation dynamics of organogel utilizing ps-ns fluorescence spectroscopy. The organogel studied in this Letter comprises bis(2-ethylhexyl) sulfosuccinate (AOT) and p-chlorophenol in the m-xylene solvent, that produce an organogel architecture with self-assembly. Within the organogel, an emitting probe, coumarin 153 (C153), is embedded. We then obtain dynamic response functions of solvation derived from the time-resolved fluorescence spectra of C153. We propose that total energy of the C153-organogel system relaxes with a relaxation time of 3.9 ns, whereas the entire rearrangement of the organogel structure around C153 is achieved with that of 6.1 ns, respectively.

  19. The effect of water on the microstructure and properties of benzene/[bmim][AOT]/[bmim][BF4] microemulsions.

    Science.gov (United States)

    Bai, Tingting; Ge, Rile; Gao, Yanan; Chai, Jinling; Slattery, John M

    2013-11-28

    In the present contribution, results concerning the role of small amounts of water in the 1-butyl-3-methylimidazolium bis 2-ethylhexyl sulfosuccinate ([bmim][AOT]) based 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF4])-in-benzene reverse microemulsions are emphasized. The microemulsion aggregates have demonstrated features in common with traditional aqueous systems, such as a normal microemulsion droplet size and decreased stability due to the addition of a polar component. Dynamic light scattering (DLS) showed that the size change of microemulsion with added water depends on the loaded [bmim][BF4] content in the microemulsion: when the [bmim][BF4] content is low, the microemulsion diameter first decreases and then increases, while the size remains about the same for microemulsions with a moderate [bmim][BF4] loading and a successive increase in size was found for high-loaded [bmim][BF4] microemulsions. (1)H NMR along with two-dimensional rotating frame nuclear Overhauser effect (NOE) experiments (ROESY) revealed that water molecules formed wide interactions with both 1-butyl-3-methylimidazolium ([bmim]) and bis 2-ethylhexyl sulfosuccinate ([AOT]), leading to a decrease in the headgroup area of [bmim][AOT], i.e. α value, which will decrease the microemulsion size. On the other hand, addition of water can simultaneously swell the microemulsions, causing an increase in the diameter. It is also deduced that the Coulomb forces between the [AOT] and [bmim] should be one of the main driving forces for the formation of [bmim][BF4]-in-benzene microemulsions.

  20. Test Your Sodium Smarts

    Science.gov (United States)

    ... You may be surprised to learn how much sodium is in many foods. Sodium, including sodium chloride ... foods with little or no salt. Test your sodium smarts by answering these 10 questions about which ...

  1. Low sodium diet (image)

    Science.gov (United States)

    ... for you. Look for these words on labels: low-sodium, sodium-free, no salt added, sodium-reduced, or ... for you. Look for these words on labels: low-sodium, sodium-free, no salt added, sodium-reduced, or ...

  2. Proton-conducting membrane based on epoxy resin-poly(vinyl alcohol)-sulfosuccinic acid blend and its nanocomposite with sulfonated multiwall carbon nanotubes for fuel-cell application

    Science.gov (United States)

    Kakati, Nitul; Das, Gautam; Yoon, Young Soo

    2016-01-01

    A blend of poly(vinyl alcohol) (PVA) with diglycidyl ether of bisphenol-A (DGB) in the presence of sulfosuccinic acid (SSA) was investigated as hydrolytically-stable proton-conducting membrane. The PVA modification was carried out by varying the DGB:SSA ratio (20:20, 10:20, and 5:20). A nanocomposite of the blend (20:20) was prepared with sulfonated multiwall carbon nanotubes (viz., 1, 3 and 5 wt%). The water uptake behavior and the proton conductivity of the prepared membranes were evaluated. The ionic conductivity of the membranes and the water uptake behavior depended on the s-MWCNT and the DGB contents. The ionic conductivity showed an enhancement for the blend and for the nanocomposite membrane as compared to the pristine polymer.

  3. Quinapyramine sulfate-loaded sodium alginate nanoparticles show enhanced trypanocidal activity.

    Science.gov (United States)

    Manuja, Anju; Kumar, Sandeep; Dilbaghi, Neeraj; Bhanjana, Gaurav; Chopra, Meenu; Kaur, Harmanmeet; Kumar, Rajender; Manuja, Balvinder K; Singh, Shailendra K; Yadav, Suresh C

    2014-08-01

    To reduce the dose, toxic effects and to ensure sustained release of quinapyramine sulfate (QS), a highly effective drug against Trypanosoma evansi. QS-loaded sodium alginate nanoparticles (QS-NPs) were formed by emulsion-crosslinking technology using dioctyl-sodium-sulfosuccinate and sodium alginate. The formulation was characterized for size, stability, morphology and functional groups by a zetasizer, scanning electron microscopy, atomic force microscopy, transmission electron microscopy and Fourier transform infrared spectroscopy. In vitro safety and toxicity studies were performed by metabolic assay in Vero cell lines, and in vivo efficacy was evaluated in mice. QS-NPs were <60 nm with 96.48% entrapment efficiency and 3.70% drug loading. The formulation showed an initial burst effect followed by slow drug release in accordance with quasi-Fickian Higuchi diffusion mechanism. QS-NPs were much less toxic and able to clear the parasite at a much lower concentration than QS. The QS-NPs synthesized are safe, less toxic and highly effective compared with QS.

  4. Preparation of ZrO2 nano-particles by the hydrolysis of ZrOCl2 solution in the reverse micelles

    Institute of Scientific and Technical Information of China (English)

    Chensha Li; Tongxiang Liang; Tianyong Luo

    2006-01-01

    Zirconia nano-particles have been produced by the hydrolysis of ZrOGl2 solution in the reverse micelles of a liquid-liquid two-phase system, in which sodium bis(2-ethylhexyl) sulfosuccinite (AOT) and toluene were chosen as the surfactant and organic phase, respectively. The reverse micelles prevented the aggregation of primary particles and reduced the diameters of zirconia nanoparticles. Superfine zirconia powders soft-aggregated by the zirconia nano-particles were obtained. The diameters of zirconia nanoparticles were influenced by the quantity of the surfactant.

  5. Influence of microwave radiation on the growth of gold nanoparticles and microporous zincophosphates in a reverse micellar system.

    Science.gov (United States)

    Doolittle, John W; Dutta, Prabir K

    2006-05-09

    The water core of reverse micelles has been extensively used as the site for synthesis of a variety of materials. However, water-in-oil reverse micelles have a limited range of temperatures over which they are stable as a single phase. Directing heat to the water cores, the usual site of synthesis without heating the bulk provides added opportunities for synthesis. Microwave radiation is a method for superheating the water cores. In this study, we use an H2O-sodium bis(2-ethylhexyl) sulfosuccinate (AOT)-heptane reverse micelle system for the synthesis of Au particles by hydrazine reduction of HAuCl4 in the presence and absence of microwave radiation. The duration of the microwave radiation was limited to a 2-min duration at a power of 300 W, thereby ensuring that the reverse micelle phase is maintained during the synthesis. At all hydrazine concentrations studied (0.5-2 M), the presence of microwave radiation led to an increase in the particle size of Au. The second system examined was the growth of microporous zincophosphate-X (ZnPO-X, an analogue of the faujasite structure) synthesized from H2O-dioctyldimethylammonium chloride (DODMAC)-heptane reverse micelle system. Microwave radiation was applied for 1 min at 150 W at various stages of the nucleation and growth process, and did not disrupt the reverse micelle system. Product analysis after 48 h of reaction showed that the 1-min microwave pulse, if applied during the nucleation stage (the first 4 h), promoted the formation of NaZnPO4.H2O over ZnPO-X. The effect of the microwave pulse at the growth stage was to promote the formation of ZnPO-X. Absorption of the microwave radiation by the water core and surrounding polar surfactant molecules leads to a rapid rise in local temperature (predicted to be approximately 150 degrees C/min for the AOT system), increasing the rates of intramicellar reactions.

  6. Fragmentation of the lamellae and fractionation of polymer coils upon mixing poly(dimethylacrylamide) with the lamellar phase of aerosol OT in water.

    Science.gov (United States)

    Pacios, Isabel E; Renamayor, Carmen S; Horta, Arturo; Lindman, Björn; Thuresson, Krister

    2005-12-22

    The lamellar mesophase formed by surfactant 1,4-bis(2-ethylhexyl) sodium sulfosuccinate (AOT) in deuterated water is mixed with poly(dimethylacrylamide) (PDMAA) polymers of low molecular weight (Mn= (2-20) x 10(3)). The mixtures separate into microphases (lamellar plus isotropic polymer solution). Their microstructures are studied by microscopy, small-angle X-ray scattering (SAXS), and deuterium NMR (2H NMR). According to SAXS, the lamellar phase fractionates the molecular weight distribution of the polymer, by dissolving only chains with coil sizes smaller than the thickness of the water layers between lamellae, and keeping larger chains segregated from the lamellar phase. The fraction of polymer that is segregated from the lamellar phase grows with Mn of the polymer. In 2H NMR, there are two signals, a quadrupolar doublet (water molecules hydrating the anisotropic lamellar phase contribute to this doublet) and a singlet (water molecules in the isotropic polymer solution contribute to this singlet). These two signals are deconvoluted to analyze the phases. Mixing with the polymer produces the partial dispersion of the lamellar phase into small fragments (microcrystallites). The structure of these microcrystallites is such that they conserve the regular long period spacing of the macrophase, and are thus identified in SAXS, but they are smaller than the minimum size required to produce quadrupolar splitting (about 4 microm), and therefore, in 2H NMR, they contribute to the singlet. 2H NMR can thus not distinguish between small microcrystallites and an isotropic polymer solution segregated from the lamellar phase; instead small microcrystallites are detected as an apparent increase of the isotropic solution. The degree of dispersion produced by the polymer in the lamellar phase is correlated with the degree of segregation that the polymer suffers. Thus, much greater dispersion into microcrystallites is produced by the higher Mn polymers than by the lower Mn polymers

  7. Synthesis, Structure and Hydration of Sodium Dioleyl Sulfosuccinate%琥珀酸二油脂磺酸钠的合成、结构及水合作用

    Institute of Scientific and Technical Information of China (English)

    于艳春; 肖鹤鸣

    2009-01-01

    通过增加磺化反应时间.补加NaHSO,,以液液萃取法代替重结品法提纯产品,大幅度提高了合成琥珀酸二油酯磺酸钠(sDss)的产品得率.用量子化学密度泛函理论以及B3LYP/6-31G@·方法全优化计算了SDSS阴离子的几何和电子结构,确证其反反-异构体较为稳定,解释了以相关反胶束提取蛋白质的实验事实.还在B3LYP/6-31G·水平上研究了 SDSS阴离子的水合作用,报道了 SDSS阴离了水合物的几何、电了结构和水合能,阐述了SDSS阴离子的亲水机理.

  8. Drug: D04406 [KEGG MEDICUS

    Lifescience Database Archive (English)

    Full Text Available D04406 Mixture, Drug Dioctyl sodium sulfosuccinate - casanthranol mixt; Vemas S (TN...) Dioctyl sodium sulfosuccinate [DR:D00305], Casanthranol [DR:D03417] Therapeutic category: 2359 Therapeutic...Purgatives, clysters 2359 Others D04406 Dioctyl sodium sulfosuccinate - casanthranol mixt PubChem: 17398095 ...

  9. Study of Removing Magnesium from Wet - Process Phosphoric Acid by Emulsi on Liquid Membrane Technique Using Bis(2- ethylhexyl) Phospate Acid as Carrier%乳状液膜法去除湿法磷酸中Mg(Ⅱ)的研究

    Institute of Scientific and Technical Information of China (English)

    高枫; 郭瓦力; 王祝敏; 孙怀宇; 刘涛

    2005-01-01

    采用乳化液膜技术对湿法磷酸进行脱镁净化是一种净化湿法磷酸的新途径.以二(2一乙基己基)磷酸酯为流动载体乳状液膜体系,系统研究了油水体积比(Roi)、膜试剂、增稠剂(石蜡量)、外水相pH值等因素对Mg(Ⅱ)的迁移行为.得出了乳化液膜法去除湿法磷酸中镁离子的最佳工艺条件:表面活性剂:L113A,膜试剂:环己烷;反萃取剂:HCl 3 mol/L,增稠剂:石蜡量0.5 mL.

  10. Diclofenac sodium overdose

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/article/002630.htm Diclofenac sodium overdose To use the sharing features on this page, please enable JavaScript. Diclofenac sodium is a prescription medicine used to relieve pain ...

  11. Naproxen sodium overdose

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/article/002507.htm Naproxen sodium overdose To use the sharing features on this page, please enable JavaScript. Naproxen sodium is a nonsteroidal anti-inflammatory drug (NSAID) used ...

  12. Docusate Sodium and Pregnancy

    Science.gov (United States)

    ... live chat Live Help Fact Sheets Share Docusate Sodium Friday, 01 April 2016 In every pregnancy, a ... This sheet talks about whether exposure to docusate sodium may increase the risk for birth defects over ...

  13. Sodium carbonate poisoning

    Science.gov (United States)

    Sodium carbonate (known as washing soda or soda ash) is a chemical found in many household and ... products. This article focuses on poisoning due to sodium carbonate. This article is for information only. Do ...

  14. Sodium Ferric Gluconate Injection

    Science.gov (United States)

    Sodium ferric gluconate injection is used to treat iron-deficiency anemia (a lower than normal number of ... are also receiving the medication epoetin (Epogen, Procrit). Sodium ferric gluconate injection is in a class of ...

  15. Sodium sieving in children.

    NARCIS (Netherlands)

    Rusthoven, E.; Krediet, R.T.; Willems, H.L.; Monnens, L.A.H.; Schroder, C.H.

    2005-01-01

    Sodium sieving is a consequence of dissociation between the amount of water and sodium transported over the peritoneal membrane. This dissociation occurs in the presence of aquaporin-mediated water transport. Sieving of sodium can be used as a rough measure for aquaporin-mediated water transport. Ic

  16. Sodium in feline nutrition.

    Science.gov (United States)

    Nguyen, P; Reynolds, B; Zentek, J; Paßlack, N; Leray, V

    2016-08-23

    High sodium levels in cat food have been controversial for a long time. Nonetheless, high sodium levels are used to enhance water intake and urine volume, with the main objective of reducing the risk of urolithiasis. This article is a review of current evidence of the putative risks and benefits of high dietary sodium levels. Its secondary aim is to report a possible safe upper limit (SUL) for sodium intake. The first part of the manuscript is dedicated to sodium physiology, with a focus on the mechanisms of sodium homeostasis. In this respect, there is only few information regarding possible interactions with other minerals. Next, the authors address how sodium intake affects sodium balance; knowledge of these effects is critical to establish recommendations for sodium feed content. The authors then review the consequences of changes in sodium intake on feline health, including urolithiasis, blood pressure changes, cardiovascular alterations and kidney disease. According to recent, long-term studies, there is no evidence of any deleterious effect of dietary sodium levels as high as 740 mg/MJ metabolizable energy, which can therefore be considered the SUL based on current knowledge.

  17. Renal sodium handling and sodium sensitivity

    Directory of Open Access Journals (Sweden)

    Alissa A. Frame

    2017-06-01

    Full Text Available The pathophysiology of hypertension, which affects over 1 billion individuals worldwide, involves the integration of the actions of multiple organ systems, including the kidney. The kidney, which governs sodium excretion via several mechanisms including pressure natriuresis and the actions of renal sodium transporters, is central to long term blood pressure regulation and the salt sensitivity of blood pressure. The impact of renal sodium handling and the salt sensitivity of blood pressure in health and hypertension is a critical public health issue owing to the excess of dietary salt consumed globally and the significant percentage of the global population exhibiting salt sensitivity. This review highlights recent advances that have provided new insight into the renal handling of sodium and the salt sensitivity of blood pressure, with a focus on genetic, inflammatory, dietary, sympathetic nervous system and oxidative stress mechanisms that influence renal sodium excretion. Increased understanding of the multiple integrated mechanisms that regulate the renal handling of sodium and the salt sensitivity of blood pressure has the potential to identify novel therapeutic targets and refine dietary guidelines designed to treat and prevent hypertension.

  18. Cerebrospinal fluid sodium rhythms

    Directory of Open Access Journals (Sweden)

    Johnson Benjamin

    2010-01-01

    Full Text Available Abstract Background Cerebrospinal fluid (CSF sodium levels have been reported to rise during episodic migraine. Since migraine frequently starts in early morning or late afternoon, we hypothesized that natural sodium chronobiology may predispose susceptible persons when extracellular CSF sodium increases. Since no mammalian brain sodium rhythms are known, we designed a study of healthy humans to test if cation rhythms exist in CSF. Methods Lumbar CSF was collected every ten minutes at 0.1 mL/min for 24 h from six healthy participants. CSF sodium and potassium concentrations were measured by ion chromatography, total protein by fluorescent spectrometry, and osmolarity by freezing point depression. We analyzed cation and protein distributions over the 24 h period and spectral and permutation tests to identify significant rhythms. We applied the False Discovery Rate method to adjust significance levels for multiple tests and Spearman correlations to compare sodium fluctuations with potassium, protein, and osmolarity. Results The distribution of sodium varied much more than potassium, and there were statistically significant rhythms at 12 and 1.65 h periods. Curve fitting to the average time course of the mean sodium of all six subjects revealed the lowest sodium levels at 03.20 h and highest at 08.00 h, a second nadir at 09.50 h and a second peak at 18.10 h. Sodium levels were not correlated with potassium or protein concentration, or with osmolarity. Conclusion These CSF rhythms are the first reports of sodium chronobiology in the human nervous system. The results are consistent with our hypothesis that rising levels of extracellular sodium may contribute to the timing of migraine onset. The physiological importance of sodium in the nervous system suggests that these rhythms may have additional repercussions on ultradian functions.

  19. Solubilities of sodium nitrate, sodium nitrite, and sodium aluminate in simulated nuclear waste

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, D.A.; Herting, D.L.

    1984-09-01

    Solubilities were determined for sodium nitrate, sodium nitrite, and sodium aluminate in synthetic nuclear waste liquor. Solubilities were determined as a function of temperature and solution composition (concentrations of sodium hydroxide, sodium nitrate, sodium nitrite, and sodium aluminate). Temperature had the greatest effect on the solubilities of sodium nitrate and sodium nitrite and a somewhat lesser effect on sodium aluminate solubility. Hydroxide had a great effect on the solubilities of all three salts. Other solution components had minor effects. 2 references, 8 figures, 11 tables.

  20. Decode the Sodium Label Lingo

    Science.gov (United States)

    ... For Preschooler For Gradeschooler For Teen Decode the Sodium Label Lingo Published January 24, 2013 Print Email Reading food labels can help you slash sodium. Here's how to decipher them. "Sodium free" or " ...

  1. [Sodium and hypertension].

    Science.gov (United States)

    de Wardener, H E

    1996-09-01

    Over several million years the human race was programmed to eat a diet which contained about 15 mmol of sodium (1 g of sodium chloride) per day. It is only five to ten thousand years ago that we became addicted to salt. Today we eat about 150 mmol of sodium (9-12 g of salt) per day. It is now apparent that this sudden rise in sodium intake (in evolutionary terms) is the most likely cause for the rise in blood pressure with age that occurs in the majority of the world's population. Those which consume less than 60 mmol/day do not develop hypertension. The reason for the rise in sodium intake is not known but it is probable that an important stimulus was the discovery that meat could be preserved by immersion into a concentrated salt solution. This seemingly miraculous power endowed salt with such magical and medicinal qualities that it became a symbol of goodness and health. It was not until 1904 Ambard and Beaujard suggested that on the contrary dietary salt could be harmful and raise the blood pressure. At first the idea did not prosper and it continues to be opposed by a diminishing band. The accumulated evidence that sodium intake is related to the blood pressure in normal man and animals and in inherited forms of hypertension has been obtained from experimental manipulations and studies of human populations. The following observation links sodium and hypertension. An increase in sodium intakes raises the blood pressure of the normal rat, dog, rabbit, baboon, chimpanzee and man. Population studies have demonstrated a significant correlation between sodium intake and the customary rise in blood pressure with age. The development of hypertensive strains of rats has revealed that the primary genetic lesion which gives rise to hypertension resides in the kidney where it impairs the urinary excretion of sodium. There is similar but less convincing evidence in essential hypertension. The kidney in both essential hypertension and hypertensive strains of rats share a

  2. Methodology for Extraction of Remaining Sodium of Used Sodium Containers

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Minhwan; Kim, Jongman; Cho, Youngil; Jeong, Jiyoung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    Sodium used as a coolant in the SFR (Sodium-cooled Fast Reactor) reacts easily with most elements due to its high reactivity. If sodium at high temperature leaks outside of a system boundary and makes contact with oxygen, it starts to burn and toxic aerosols are produced. In addition, it generates flammable hydrogen gas through a reaction with water. Hydrogen gas can be explosive within the range of 4.75 vol%. Therefore, the sodium should be handled carefully in accordance with standard procedures even though there is a small amount of target sodium remainings inside the containers and drums used for experiment. After the experiment, all sodium experimental apparatuses should be dismantled carefully through a series of draining, residual sodium extraction, and cleaning if they are no longer reused. In this work, a system for the extraction of the remaining sodium of used sodium drums has been developed and an operation procedure for the system has been established. In this work, a methodology for the extraction of remaining sodium out of the used sodium container has been developed as one of the sodium facility maintenance works. The sodium extraction system for remaining sodium of the used drums was designed and tested successfully. This work will contribute to an establishment of sodium handling technology for PGSFR. (Prototype Gen-IV Sodium-cooled Fast Reactor)

  3. Sodium urine test

    Science.gov (United States)

    ... urine sodium level may be a sign of: Adrenal glands releasing too much hormone ( hyperaldosteronism ) Not enough fluid in the body (dehydration) Diarrhea and fluid loss Heart failure Kidney problems, such as chronic kidney disease or ...

  4. Skeletal muscle sodium channelopathies.

    Science.gov (United States)

    Nicole, Sophie; Fontaine, Bertrand

    2015-10-01

    This is an update on skeletal muscle sodium channelopathies since knowledge in the field have dramatically increased in the past years. The relationship between two phenotypes and SCN4A has been confirmed with additional cases that remain extremely rare: severe neonatal episodic laryngospasm mimicking encephalopathy, which should be actively searched for since patients respond well to sodium channel blockers; congenital myasthenic syndromes, which have the particularity to be the first recessive Nav1.4 channelopathy. Deep DNA sequencing suggests the contribution of other ion channels in the clinical expressivity of sodium channelopathies, which may be one of the factors modulating the latter. The increased knowledge of channel molecular structure, the quantity of sodium channel blockers, and the availability of preclinical models would permit a most personalized choice of medication for patients suffering from these debilitating neuromuscular diseases. Advances in the understanding of the molecular structure of voltage-gated sodium channels, as well as availability of preclinical models, would lead to improved medical care of patients suffering from skeletal muscle, as well as other sodium channelopathies.

  5. Cardiac sodium channelopathies.

    Science.gov (United States)

    Amin, Ahmad S; Asghari-Roodsari, Alaleh; Tan, Hanno L

    2010-07-01

    Cardiac sodium channel are protein complexes that are expressed in the sarcolemma of cardiomyocytes to carry a large inward depolarizing current (INa) during phase 0 of the cardiac action potential. The importance of INa for normal cardiac electrical activity is reflected by the high incidence of arrhythmias in cardiac sodium channelopathies, i.e., arrhythmogenic diseases in patients with mutations in SCN5A, the gene responsible for the pore-forming ion-conducting alpha-subunit, or in genes that encode the ancillary beta-subunits or regulatory proteins of the cardiac sodium channel. While clinical and genetic studies have laid the foundation for our understanding of cardiac sodium channelopathies by establishing links between arrhythmogenic diseases and mutations in genes that encode various subunits of the cardiac sodium channel, biophysical studies (particularly in heterologous expression systems and transgenic mouse models) have provided insights into the mechanisms by which INa dysfunction causes disease in such channelopathies. It is now recognized that mutations that increase INa delay cardiac repolarization, prolong action potential duration, and cause long QT syndrome, while mutations that reduce INa decrease cardiac excitability, reduce electrical conduction velocity, and induce Brugada syndrome, progressive cardiac conduction disease, sick sinus syndrome, or combinations thereof. Recently, mutation-induced INa dysfunction was also linked to dilated cardiomyopathy, atrial fibrillation, and sudden infant death syndrome. This review describes the structure and function of the cardiac sodium channel and its various subunits, summarizes major cardiac sodium channelopathies and the current knowledge concerning their genetic background and underlying molecular mechanisms, and discusses recent advances in the discovery of mutation-specific therapies in the management of these channelopathies.

  6. Development of sodium technology

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Sung Tai; Nam, H. Y.; Choi, Y. D. [and others

    2000-05-01

    The objective of present study is to produce the experimental data for development and verification of computer codes for development of LMR and to develop the preliminary technologies for the future large scale verification experiments. A MHD experimental test loop has been constructed for the quantitative analysis of the effect of magnetic field on the sodium flow and experiments are carried out for three EM pumps. The previous pressure drop correlations are evaluated using the experimental data obtained from the pressure drop experiment in a 19-pin fuel assembly with wire spacer. An dimensionless variable is proposed to describe the amplitude and frequency of the fluctuation of free surface using the experimental data obtained from free surface experimental apparatus and an empirical correlation is developed using this dimensionless variable. An experimental test loop is constructed to measure the flow characteristics in IHX shell side and the local pressure drop in fuel assembly, and to test the vibration behaviour of fuel pins due to flow induced vibration. The sodium two-phase flow measuring technique using the electromagnetic flowmeter is developed and the sodium differential pressure drop measuring technique using the method of direct contact of sodium and oil is established. The work on the analysis of sodium fire characteristics and produce data for vlidation of computer code is performed. Perfect reopen time of self plugged leak path was observed to be about 130 minutes after water leak initiation. Reopen shape of a specimen appeared to be double layer of circular type, and reopen size of this specimen surface was about 2mm diameter on sodium side. In small water leakage experiments, the following correlation equation about the reopen time between sodium temperature and initial leak rate was obtained, {tau}{sub c} = {delta}{center_dot}g{sup -0.83}{center_dot}10{sup (3570/T{sub Na}-3.34)}, in 400-500 deg C of liquid sodium atmosphere. The characteristics

  7. Base stable quaternary ammonium ionic liquids

    OpenAIRE

    Lethesh, Kallidanthiyil Chellappan; Dehaen, Wim; Binnemans, Koen

    2014-01-01

    Ionic liquids with the bis(2-ethylhexyl)dimethylammonium cation, [BEDMA]+, were prepared by a halide-free route starting from the readily available secondary amine bis(2-ethylhexyl)amine. The following anions were considered: chloride, bromide, iodide, nitrate, hydrogensulphate, dihydrogenphosphate, formate, acetate, propionate, trifluoroacetate, methyl sulphate, methanesulphonate, tosylate, isonicotinate, nicotinate and picolinate. Several of the compounds are room-temperature ionic liquids,...

  8. Melting of sodium clusters

    CERN Document Server

    Reyes-Nava, J A; Beltran, M R; Michaelian, K

    2002-01-01

    Thermal stability properties and the melting-like transition of Na_n, n=13-147, clusters are studied through microcanonical molecular dynamics simulations. The metallic bonding in the sodium clusters is mimicked by a many-body Gupta potential based on the second moment approximation of a tight-binding Hamiltonian. The characteristics of the solid-to-liquid transition in the sodium clusters are analyzed by calculating physical quantities like caloric curves, heat capacities, and root-mean-square bond length fluctuations using simulation times of several nanoseconds. Distinct melting mechanisms are obtained for the sodium clusters in the size range investigated. The calculated melting temperatures show an irregular variation with the cluster size, in qualitative agreement with recent experimental results. However, the calculated melting point for the Na_55 cluster is about 40 % lower than the experimental value.

  9. Too Much Sodium

    Centers for Disease Control (CDC) Podcasts

    2012-02-07

    This podcast is based on the February 2012 CDC Vital Signs report. Ninety percent of Americans age two and older eat too much sodium which can increase your risk for high blood pressure and often leads to heart disease and stroke, two leading causes of death in the US. Learn several small steps you can take to reduce the amount of sodium in your diet.  Created: 2/7/2012 by Centers for Disease Control and Prevention (CDC).   Date Released: 2/7/2012.

  10. 不同反胶束体系后萃取花生蛋白质的比较%Comparison of the Backward Extraction of Peanut Protein in Different Reverse Micelles

    Institute of Scientific and Technical Information of China (English)

    高艳秀; 陈复生; 郭珍; 杨颖莹; 李润洁

    2013-01-01

    对AOT[二-(2-乙基己基)琥珀酸酯磺酸钠]/异辛烷,SDS(十二烷基硫酸钠)/异辛烷-正辛醇,DTAC(十二烷基三甲基氯化铵)/正庚烷-正己醇3种反胶束体系萃取花生蛋白质的后萃工艺进行研究.主要研究了缓冲溶液pH值、萃取时间、萃取温度、超声功率、KCl浓度对花生蛋白后萃率的影响,分别得到了3种反胶束体系萃取花生蛋白质的最佳后萃工艺条件,并做验证试验.在最优工艺条件下制备不同的花生蛋白样品.通过色差分析,从宏观上比较不同反胶束体系制备的花生蛋白产品色泽的差异,进一步对比不同反胶束体系制备的花生蛋白的扫描电镜(SEM)照片,分析其微观结构的差别,试验结果表明最适合萃取花生蛋白的反胶束体系是AOT反胶束体系,且该体系萃取花生蛋白的后萃率为83.17%,较另外2种体系的后萃率都高.%Peanut protein was extracted using AOT[sodium bis-(2-ethylhexyl) sulfosuccinate] / isooctane,SDS (sodium dodecyl sulfonate) / isooctane-heptylane capryl alcohol,DTAC (heptanes-hexanol reverse micelle systems,and the backward extraction was studied.The effects of pH,extraction time,and temperature,ultrasonic power,KCl concentration on the backward extraction rates were investigated.And the optimum conditions of the three reverse micelle systems in the backward extraction were obtained and verification test were designed to verify the results.On the optimum conditions,various peanut protein samples were prepared.Through the color difference analysis,we compared the color difference of respective peanut protein products on macroscopic.Furthermore,comparing scanning electron microscopy (SEM) pictures of three kinds of peanut proteins extracted from the respective reverse micelle systems,we analyzed the differences of microstructure.The results of the test showed that the most suitable reverse micelle system for the extraction of peanut protein was AOT reverse micelle system; the

  11. Cardiac sodium channelopathies

    NARCIS (Netherlands)

    Amin, A.S.; Asghari-Roodsari, A.; Tan, H.L.

    2010-01-01

    Cardiac sodium channel are protein complexes that are expressed in the sarcolemma of cardiomyocytes to carry a large inward depolarizing current (I-Na) during phase 0 of the cardiac action potential. The importance of I-Na for normal cardiac electrical activity is reflected by the high incidence of

  12. Cardiac sodium channelopathies

    NARCIS (Netherlands)

    Amin, A.S.; Asghari-Roodsari, A.; Tan, H.L.

    2010-01-01

    Cardiac sodium channel are protein complexes that are expressed in the sarcolemma of cardiomyocytes to carry a large inward depolarizing current (I-Na) during phase 0 of the cardiac action potential. The importance of I-Na for normal cardiac electrical activity is reflected by the high incidence of

  13. Sodium fluxes in sweet pepper exposed to varying sodium concentrations

    NARCIS (Netherlands)

    Blom-Zandstra, M.; Vogelzang, S.A.; Veen, B.W.

    1998-01-01

    The sodium transport and distribution of sweet pepper (Capsicum annuum L.) under saline conditions were studied after transferring the plants to a sodium-free nutrient solution. Sodium stress up to 60 mM did not affect the growth of sweet pepper, as it appears able to counteract the unfavourable phy

  14. Sodium fluxes in sweet pepper exposed to varying sodium concentrations

    NARCIS (Netherlands)

    Blom-Zandstra, M.; Vogelzang, S.A.; Veen, B.W.

    1998-01-01

    The sodium transport and distribution of sweet pepper (Capsicum annuum L.) under saline conditions were studied after transferring the plants to a sodium-free nutrient solution. Sodium stress up to 60 mM did not affect the growth of sweet pepper, as it appears able to counteract the unfavourable

  15. Technology for sodium purity control

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Ji Young; Kim, B. H.; Kim, T. J. [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-10-01

    When sodium is used as heat transfer fluid, the plugging in coolant flow, the corrosion of structure material and the transfer of radioactive material caused by the impurities in sodium are worth considerable. Accordingly, these impurities must be monitored and controlled continuously by sodium purification devices in the heat transfer system which sodium is used as coolant. Sodium purification loop was constructed for the purpose of accumulating the technology for purity control of the coolant, developing and verifying further efficient instruments for sodium purification. The plugging meter and the cold trap is used as the implement for measuring and controlling the oxygen and the hydrogen, the main impurities in sodium coolant. They are capable of excellent performance as the implements which could detect and monitor the impurities to the concentration limit required for nuclear reactor. Sodium purification loop could be used variably according to the experimental purpose. 18 refs., 34 figs., 8 tabs. (Author)

  16. Inhaled sodium metabisulphite induced bronchoconstriction: inhibition by nedocromil sodium and sodium cromoglycate.

    Science.gov (United States)

    Dixon, C M; Ind, P W

    1990-01-01

    1. The effects of nedocromil sodium and sodium cromoglycate on bronchoconstriction induced by inhaled sodium metabisulphite have been studied in eight atopic subjects, three of whom had mild asthma. 2. Nedocromil sodium (4 mg, 7.8 X 10(-6) M), sodium cromoglycate (10 mg, 24.1 X 10(-6) M) and matched placebo were administered by identical metered dose inhalers 30 min before a dose-response to sodium metabisulphite (5-100 mg ml-1) was performed. 3. Maximum fall in sGaw after placebo pre-treatment was -43.9 +/- 3.3% baseline (mean +/- s.e. mean). At the same metabisulphite concentration maximum fall in sGaw after sodium cromoglycate was -13.0 +/- 3.6% and after nedocromil sodium was +4.3 +/- 6.8%. Nedocromil sodium prevented any significant fall in sGaw even after higher concentrations of metabisulphite. 4. Both nedocromil sodium, 4 mg, and sodium cromoglycate, 10 mg, inhibited sodium metabisulphite induced bronchoconstriction but nedocromil sodium was significantly more effective. Relative in vivo potency of the two drugs is broadly in line with other in vivo and in vitro studies. PMID:2171616

  17. Slicing sodium from bakery products

    NARCIS (Netherlands)

    Noort, M.

    2012-01-01

    The need for sodium reduction in our diet is clear to consumers, dieticians and food manufacturers. As sodium concentration has a strengthening effect on gluten, sodium reduction decreases dough mixing tolerance, dough resistance and induces dough stickiness. In particular, the latter may cause

  18. Slicing sodium from bakery products

    NARCIS (Netherlands)

    Noort, M.

    2012-01-01

    The need for sodium reduction in our diet is clear to consumers, dieticians and food manufacturers. As sodium concentration has a strengthening effect on gluten, sodium reduction decreases dough mixing tolerance, dough resistance and induces dough stickiness. In particular, the latter may cause prob

  19. Hanford site sodium management plan

    Energy Technology Data Exchange (ETDEWEB)

    Guttenberg, S.

    1995-09-25

    The Hanford Site Sodium Management Plan, Revision 1, provides changes to the major elements and management strategy to ensure an integrated and coordinated approach for disposition of the more than 350,000 gallons of sodium and related sodium facilities located at the DOE`s Hanford Site

  20. Sodium hydride precipitation in sodium cold traps

    Energy Technology Data Exchange (ETDEWEB)

    McPheeters, C.C.; Raue, D.J.

    1980-06-01

    A series of experiments have been performed to test a calculational model for precipitation of NaH in sodium cold traps. The calculational model, called ACTMODEL, is a computer simulation that uses the system geometry and operating conditions as input to calculate a mass-transfer coefficient and the distribution of NaH in a cold trap. The ACTMODEL was tested using an analytical cold trap (ACT) that is simple and essentially one-dimensional. The ACT flow and temperature profile can be controlled at any desired condition. The ACT was analyzed destructively after each test to measure the actual NaH distribution. Excellent agreement was obtained between the ACTMODEL simulations and the experiments. Mass-transfer coefficients ranging upward from 6 x 10/sup -5/ m/s were measured in both packless and packed traps. As much as a fourfold increase in precipitation surface area was observed with increasing amount of NaH deposited. 11 figures, 2 tables.

  1. 21 CFR 201.64 - Sodium labeling.

    Science.gov (United States)

    2010-04-01

    ... paragraph (b) of this section). (e) The term very low sodium may be used in the labeling of OTC drug... milligrams or less. (f) The term low sodium may be used in the labeling of OTC drug products intended for... substituted for the term sodium. (h) The terms sodium free, very low sodium, and low sodium shall be in print...

  2. A small angle neutron scattering study on the mixtures of pluronic L121 and anionic surfactant AOT

    Indian Academy of Sciences (India)

    G Ghosh; V K Aswal; D Varade

    2008-11-01

    Small angle neutron scattering (SANS) experiments have been carried out on the micellar solutions containing mixtures of a hydrophobic triblock copolymer (L121, EO5PO68EO5) and a hydrophobic anionic surfactant (AOT, sodium bis(2-ethylhexyl)sulphosuccinate) in water with varying ratio () of AOT to L121 for = 0.15, 0.2, 0.3, 0.5 and 0.6. It is known that either L121 or AOT alone forms vesicles in water, but in the mixture with appropriate ratio of the two components a thermodynamically stable, isotropic solution of apparently small micelle-like aggregates is formed. We find that these micelles are prolate ellipsoidal.

  3. Surface modification of Fe304 nanoparticles and their magnetic properties

    Institute of Scientific and Technical Information of China (English)

    Hao Yan; Jian-cheng Zhang; Chen-xia You; Zhen-wei Song; Ben-wei Yu; Yue Shen

    2009-01-01

    Fe3O4 magnetic nanoparticles were synthesized by the hydrothermal method, and the influences of the surfactant sodium bis(2-ethylhexyl) sulfosuecinate (AOT) on the particles were investigated. The structure, morphology, and magnetic properties of the products were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infra-red spectroscopy (FT-IR), and vibrating sample magnetometer (VSM). It is confirmed that the as-prepared nanopartieles have been modified by using the surfactant during the synthesis process. The amount of the surfactant has an effect on the size, the dispersal, and the magnetic properties of the particles. Besides, the mechanisms of the influences were also discussed.

  4. A study on sodium-concrete reaction

    Energy Technology Data Exchange (ETDEWEB)

    Bae, Jae Heum; Min, Byong Hun [Suwon University, Suwon (Korea, Republic of)

    1997-07-01

    A small sodium-concrete reaction facility was designed, manufactured and installed. this facility has been operated under inert gas(N{sub 2}) with different experimental variables such as sodium injection temperature, injection amount of sodium, aging period of concrete, sodium reservoir temperature. As a result, it was found that sodium injection temperature and injected amount of sodium has little effect on sodium-concrete reaction. However, sodium reservoir temperature and aging period of concrete has relatively high impact on sodium-concrete reaction. Sodium-concrete reaction model has also been developed and compared with experimental results. (Author) 51 refs., 16 tabs., 64 figs.

  5. Magnetometry with mesospheric sodium

    Science.gov (United States)

    Higbie, James M.; Rochester, Simon M.; Patton, Brian; Holzlöhner, Ronald; Bonaccini Calia, Domenico; Budker, Dmitry

    2011-01-01

    Measurement of magnetic fields on the few 100-km length scale is significant for many geophysical applications including mapping of crustal magnetism and ocean circulation measurements, yet available techniques for such measurements are very expensive or of limited accuracy. We propose a method for remote detection of magnetic fields using the naturally occurring atomic sodium-rich layer in the mesosphere and existing high-power lasers developed for laser guide star applications. The proposed method offers a dramatic reduction in cost and opens the way to large-scale, parallel magnetic mapping and monitoring for atmospheric science, navigation, and geophysics. PMID:21321235

  6. Magnetometry with Mesospheric Sodium

    CERN Document Server

    Higbie, J M; Patton, B; Holzlöhner, R; Calia, D Bonaccini; Budker, D

    2009-01-01

    Measurement of magnetic fields on the few-hundred-kilometer length scale is significant for a variety of geophysical applications including mapping of crustal magnetism and ocean-circulation measurements, yet available techniques for such measurements are very expensive or of limited accuracy. We propose a scheme for remote detection of magnetic fields using the naturally occurring atomic-sodium-rich layer in the mesosphere and existing high-power lasers developed for laser guide-star applications. The proposed scheme offers dramatic reduction in cost, opening the way to large-scale magnetic mapping missions.

  7. Sodium diffusion in boroaluminosilicate glasses

    DEFF Research Database (Denmark)

    Smedskjaer, Morten M.; Zheng, Qiuju; Mauro, John C.

    2011-01-01

    of isothermal sodium diffusion in BAS glasses by ion exchange, inward diffusion, and tracer diffusion experiments. By varying the [SiO2]/[Al2O3] ratio of the glasses, different structural regimes of sodium behavior are accessed. We show that the mobility of the sodium ions decreases with increasing [SiO2]/[Al2O......3] ratio, revealing that sodium is more mobile when it acts as a charge compensator to stabilize network formers than when it acts as a creator of non-bridging oxygens on tetrahedrally-coordinated silicon and trigonal boron. The impacts of both the addition of iron and its redox state on the sodium...... be attributed to the fact that for sodium inward diffusion, the charge compensation for electron holes is a rather slow process that limits the rate of diffusion. (C) 2011 Elsevier B.V. All rights reserved....

  8. 21 CFR 184.1724 - Sodium alginate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium alginate. 184.1724 Section 184.1724 Food and... Substances Affirmed as GRAS § 184.1724 Sodium alginate. (a) Sodium alginate (CAS Reg. No. 9005-38-3) is the sodium salt of alginic acid, a natural polyuronide constituent of certain brown algae. Sodium alginate...

  9. Sodium-glucose cotransport

    Science.gov (United States)

    Poulsen, Søren Brandt; Fenton, Robert A.; Rieg, Timo

    2017-01-01

    Purpose of review Sodium-glucose cotransporters (SGLTs) are important mediators of glucose uptake across apical cell membranes. SGLT1 mediates almost all sodium-dependent glucose uptake in the small intestine, while in the kidney SGLT2, and to a lesser extent SGLT1, account for more than 90% and nearly 3%, respectively, of glucose reabsorption from the glomerular ultrafiltrate. Although the recent availability of SGLT2 inhibitors for the treatment of diabetes mellitus has increased the number of clinical studies, this review has a focus on mechanisms contributing to the cellular regulation of SGLTs. Recent findings Studies have focused on the regulation of SGLT expression under different physiological/pathophysiological conditions, for example diet, age or diabetes mellitus. Several studies provide evidence of SGLT regulation via cyclic adenosine monophosphate/protein kinase A, protein kinase C, glucagon-like peptide 2, insulin, leptin, signal transducer and activator of transcription-3 (STAT3), phosphoinositide-3 kinase (PI3K)/Akt, mitogen-activated protein kinases (MAPKs), nuclear factor-kappaB (NF-kappaB), with-no-K[Lys] kinases/STE20/SPS1-related proline/alanine-rich kinase (Wnk/SPAK) and regulatory solute carrier protein 1 (RS1) pathways. Summary SGLT inhibitors are important drugs for glycemic control in diabetes mellitus. Although the contribution of SGLT1 for absorption of glucose from the intestine as well as SGLT2/SGLT1 for renal glucose reabsorption has been comprehensively defined, this review provides an up-to-date outline for the mechanistic regulation of SGLT1/SGLT2. PMID:26125647

  10. Evolutionary primacy of sodium bioenergetics

    Directory of Open Access Journals (Sweden)

    Wolf Yuri I

    2008-04-01

    Full Text Available Abstract Background The F- and V-type ATPases are rotary molecular machines that couple translocation of protons or sodium ions across the membrane to the synthesis or hydrolysis of ATP. Both the F-type (found in most bacteria and eukaryotic mitochondria and chloroplasts and V-type (found in archaea, some bacteria, and eukaryotic vacuoles ATPases can translocate either protons or sodium ions. The prevalent proton-dependent ATPases are generally viewed as the primary form of the enzyme whereas the sodium-translocating ATPases of some prokaryotes are usually construed as an exotic adaptation to survival in extreme environments. Results We combine structural and phylogenetic analyses to clarify the evolutionary relation between the proton- and sodium-translocating ATPases. A comparison of the structures of the membrane-embedded oligomeric proteolipid rings of sodium-dependent F- and V-ATPases reveals nearly identical sets of amino acids involved in sodium binding. We show that the sodium-dependent ATPases are scattered among proton-dependent ATPases in both the F- and the V-branches of the phylogenetic tree. Conclusion Barring convergent emergence of the same set of ligands in several lineages, these findings indicate that the use of sodium gradient for ATP synthesis is the ancestral modality of membrane bioenergetics. Thus, a primitive, sodium-impermeable but proton-permeable cell membrane that harboured a set of sodium-transporting enzymes appears to have been the evolutionary predecessor of the more structurally demanding proton-tight membranes. The use of proton as the coupling ion appears to be a later innovation that emerged on several independent occasions. Reviewers This article was reviewed by J. Peter Gogarten, Martijn A. Huynen, and Igor B. Zhulin. For the full reviews, please go to the Reviewers' comments section.

  11. CDC Vital Signs: Where's the Sodium?

    Science.gov (United States)

    ... serve food can Consider joining voluntary initiatives to reduce sodium such as the National Salt Reduction Initiative Give choices to consumers to help them reduce sodium in their diet by: Stocking lower sodium foods. ...

  12. Are Reductions in Population Sodium Intake Achievable?

    OpenAIRE

    Levings, Jessica L.; Cogswell, Mary E.; Janelle Peralez Gunn

    2014-01-01

    The vast majority of Americans consume too much sodium, primarily from packaged and restaurant foods. The evidence linking sodium intake with direct health outcomes indicates a positive relationship between higher levels of sodium intake and cardiovascular disease risk, consistent with the relationship between sodium intake and blood pressure. Despite communication and educational efforts focused on lowering sodium intake over the last three decades data suggest average US sodium intake has r...

  13. Susceptibility of Clostridium difficile to the food preservatives sodium nitrite, sodium nitrate and sodium metabisulphite.

    Science.gov (United States)

    Lim, Su-Chen; Foster, Niki F; Riley, Thomas V

    2016-02-01

    Clostridium difficile is an important enteric pathogen of humans and food animals. Recently it has been isolated from retail foods with prevalences up to 42%, prompting concern that contaminated foods may be one of the reasons for increased community-acquired C. difficile infection (CA-CDI). A number of studies have examined the prevalence of C. difficile in raw meats and fresh vegetables; however, fewer studies have examined the prevalence of C. difficile in ready-to-eat meat. The aim of this study was to investigate the in vitro susceptibility of 11 C. difficile isolates of food animal and retail food origins to food preservatives commonly used in ready-to-eat meats. The broth microdilution method was used to determine the minimum inhibitory concentrations (MIC) and minimum bactericidal concentrations (MBC) for sodium nitrite, sodium nitrate and sodium metabisulphite against C. difficile. Checkerboard assays were used to investigate the combined effect of sodium nitrite and sodium nitrate, commonly used in combination in meats. Modal MIC values for sodium nitrite, sodium nitrate and sodium metabisulphite were 250 μg/ml, >4000 μg/ml and 1000 μg/ml, respectively. No bactericidal activity was observed for all three food preservatives. The checkerboard assays showed indifferent interaction between sodium nitrite and sodium nitrate. This study demonstrated that C. difficile can survive in the presence of food preservatives at concentrations higher than the current maximum permitted levels allowed in ready-to-eat meats. The possibility of retail ready-to-eat meats contaminated with C. difficile acting as a source of CDI needs to be investigated.

  14. Synthesis and characterization of sodium alkoxides

    Indian Academy of Sciences (India)

    K Chandran; R Nithya; K Sankaran; A Gopalan; V Ganesan

    2006-04-01

    Alcohol route is being adopted for cleaning sodium from sodium-wetted small components of coolant circuits of fast reactors. For better understanding of sodium–alcohol reactions and their energetics, the data on thermo-chemical properties such as heats of sodium–alcohol reactions, heats of dissolution, heat capacities, thermal decomposition behaviour, etc of their end products are essential. In order to generate such data, high purity sodium alkoxides, viz. sodium methoxide, sodium ethoxide and sodium -propoxide, were prepared by reacting sodium metal with respective alcohol. These compounds were characterized using X-ray diffraction technique and IR spectroscopy. The elemental analysis was carried out by CHNS analyser and atomic emission spectroscopy. Normal chain sodium alkoxides were found to exhibit tetragonal crystal structure. Crystal structures of sodium ethoxide and sodium -propoxide are reported for the first time. The IR spectrum of sodium -propoxide is also reported for the first time.

  15. Sodium management in dialysis by conductivity.

    Science.gov (United States)

    Bosetto, A; Bene, B; Petitclerc, T

    1999-07-01

    The determination of dialysate sodium concentration is one of the challenges of dialysis prescription, because no accurate information on the predialytic sodium overload is available. Too low dialysate sodium is responsible for intradialytic intolerance symptoms, whereas too high sodium may lead to long-term water sodium overload with cardiovascular hazards (hypertension, left heart failure). We propose here a biofeedback system based on noninvasive repeated measures of ionic dialysance and plasma water conductivity used here as a surrogate of plasma water sodium. This system achieves a stable postdialytic sodium pool and subsequently a dialysate sodium concentration adapted to the inter dialytic sodium load. This new tool in dialysate sodium prescription aims at reducing the morbidity related to patient sodium balance impairment.

  16. Designing microstructures for sodium reduction

    OpenAIRE

    Chiu, N. X. N.

    2016-01-01

    The aim of this project was to develop the tools and knowledge to reduce dietary sodium by mitigating restrictions to flavour delivery and enhancing saltiness perception through sodium contrast effects in the mouth. This is achieved by restructuring semi-solid and liquid model food systems to achieve maximum flavour delivery for enhanced perception. The project considered two model systems: stable foams and double emulsions. Stable foams were developed to evaluate air inclusions as a p...

  17. Stability of Ampicillin Sodium, Nafcillin Sodium, And Oxacillin Sodium in AutoDose Infusion System Bags.

    Science.gov (United States)

    Zhang, Yanping; Trissel, Lawrence A

    2002-01-01

    The objective of this study was to evaluate the physical and chemical stability of ampicillin sodium 1g/100mL, nafcillin sodium 1g/100mL, and oxacillin sodium 1g/100mL, each of which was admixed in 0.9% sodium chloride injection and packaged in an AutoDose Infusion System bag. Triplicate test samples were prepared by reconstituting the penicillin antibiotics and bringing the required amount of each drug to a final volume of 100 mL with 0.9% sodium chloride injection. The test solutions were packaged in AutoDose Bags, which are ethylene vinyl acetate plastic containers designed for use in the AutoDose Infusion System. Samples were stored protected from light and were evaluated at appropriate intervals for up to 7 days at 23 deg C and up to 30 days at 4 deg C. Physical stability was assessed by means of a multistep evaluation procedure that included both turbidimetric and particulate measurement as well as visual inspection. Chemical stability was assesed with stability-indicating high-perofrmance liquid chromatographic (HPLC) analytical techniques based on the determination of drug concentrations initially and at appropriate intervals over the study periods. All the penicillin admixtures were initially clear when viewed in normal fluorescent room light. When the admixtures were viewed with a Tyndall beam, a trace haze was observed with the ampicillin sodium and nafcillin sodium mixtures but not with the oxacillin sodium mixture. Measured turbidity and particulate content were low and exhibited little change in the ampicillin sodium and oxacillin sodium samples throughout the study. The nafcillin sodium samples stored at room temperature remained clear, but a microprecipitate developed in the refrigerated samples between 14 and 21 days of storage. All samples were essentially colorless throughout the study. HPLC analysis indicated some decomposition in the samples. Ampicillin sodium, which was the least stable, exhibited a 10% loss after 24 hours at 23 deg C. In the

  18. Dietary sodium and cardiovascular disease.

    Science.gov (United States)

    Smyth, Andrew; O'Donnell, Martin; Mente, Andrew; Yusuf, Salim

    2015-06-01

    Although an essential nutrient, higher sodium intake is associated with increasing blood pressure (BP), forming the basis for current population-wide sodium restriction guidelines. While short-term clinical trials have achieved low intake (6 months). Guidelines assume that low sodium intake will reduce BP and reduce cardiovascular disease (CVD), compared to moderate intake. However, current observational evidence suggests a J-shaped association between sodium intake and CVD; the lowest risks observed with 3-5 g/day but higher risk with 5 g/day) and increased risk of CVD. Although lower intake may reduce BP, this may be offset by marked increases in neurohormones and other adverse effects which may paradoxically be adverse. Large randomised clinical trials with sufficient follow-up are required to provide robust data on the long-term effects of sodium reduction on CVD incidence. Until such trials are completed, current evidence suggests that moderate sodium intake for the general population (3-5 g/day) is likely the optimum range for CVD prevention.

  19. Sodium voiding analysis in Kalimer

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Won-Pyo; Jeong, Kwan-Seong; Hahn, Dohee [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    2001-07-01

    A sodium boiling model has been developed for calculations of the void reactivity feedback as well as the fuel and cladding temperatures in the KALIMER core after onset of sodium boiling. The sodium boiling in liquid metal reactors using sodium as coolant should be modeled because of phenomenon difference observed from that in light water reactor systems. The developed model is a multiple -bubble slug ejection model. It allows a finite number of bubbles in a channel at any time. Voiding is assumed to result from formation of bubbles that fill the whole cross section of the coolant channel except for liquid film left on the cladding surface. The vapor pressure, currently, is assumed to be uniform within a bubble. The present study is focused on not only demonstration of the sodium voiding behavior predicted by the developed model, but also confirmation on qualitative acceptance for the model. In results, the model catches important phenomena for sodium boiling, while further effort should be made for the complete analysis. (author)

  20. Central regulation of sodium appetite.

    Science.gov (United States)

    Geerling, Joel C; Loewy, Arthur D

    2008-02-01

    Sodium appetite, the behavioural drive to ingest salt, is stimulated by prolonged physiological sodium deficiency in many animal species. The same neural mechanisms that are responsible for sodium appetite in laboratory animals may influence human behaviour as well, with particular relevance to the dietary salt intake of patients with diseases such as heart failure, renal failure, liver failure and salt-sensitive hypertension. Since the original experimental work of Curt Richter in the 1930s, much has been learned about the regulation of salt-ingestive behaviour. Here, we review data from physiology, pharmacology, neuroanatomy and neurobehavioural investigations into the stimulatory and inhibitory signals that regulate sodium appetite. A rudimentary framework is proposed for the brain circuits that integrate peripheral information representing the need for sodium with neural signals for the gustatory detection of salt in order to drive a motivated ingestive response. Based on this model, areas of remaining uncertainty are highlighted where future information would allow a more detailed understanding of the neural circuitry responsible for sodium appetite.

  1. Sodium: Tips for People with Chronic Kidney Disease (CKD)

    Science.gov (United States)

    ... l Fresh meat, poultry, seafood l Low-fat, low-sodium cheese l Unsalted nuts l Low- and reduced- ... for foods labeled: sodium free, salt free, very low sodium, low sodium, reduced or less sodium, light in ...

  2. 21 CFR 172.175 - Sodium nitrite.

    Science.gov (United States)

    2010-04-01

    ... Preservatives § 172.175 Sodium nitrite. The food additive sodium nitrite may be safely used in or on specified... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium nitrite. 172.175 Section 172.175 Food and... preservative and color fixative, with sodium nitrate, in meat-curing preparations for the home curing of...

  3. Are Reductions in Population Sodium Intake Achievable?

    Directory of Open Access Journals (Sweden)

    Jessica L. Levings

    2014-10-01

    Full Text Available The vast majority of Americans consume too much sodium, primarily from packaged and restaurant foods. The evidence linking sodium intake with direct health outcomes indicates a positive relationship between higher levels of sodium intake and cardiovascular disease risk, consistent with the relationship between sodium intake and blood pressure. Despite communication and educational efforts focused on lowering sodium intake over the last three decades data suggest average US sodium intake has remained remarkably elevated, leading some to argue that current sodium guidelines are unattainable. The IOM in 2010 recommended gradual reductions in the sodium content of packaged and restaurant foods as a primary strategy to reduce US sodium intake, and research since that time suggests gradual, downward shifts in mean population sodium intake are achievable and can move the population toward current sodium intake guidelines. The current paper reviews recent evidence indicating: (1 significant reductions in mean population sodium intake can be achieved with gradual sodium reduction in the food supply, (2 gradual sodium reduction in certain cases can be achieved without a noticeable change in taste or consumption of specific products, and (3 lowering mean population sodium intake can move us toward meeting the current individual guidelines for sodium intake.

  4. 21 CFR 522.460 - Cloprostenol sodium.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Cloprostenol sodium. 522.460 Section 522.460 Food... Cloprostenol sodium. (a)(1) Specifications. Each milliliter of the aqueous solution contains 263 micrograms of cloprostenol sodium (equivalent to 250 micrograms of cloprostenol) in a sodium citrate, anhydrous citric...

  5. 21 CFR 172.170 - Sodium nitrate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium nitrate. 172.170 Section 172.170 Food and... Preservatives § 172.170 Sodium nitrate. The food additive sodium nitrate may be safely used in or on specified... sablefish, smoked, cured salmon, and smoked, cured shad, so that the level of sodium nitrate does not...

  6. 21 CFR 173.73 - Sodium polyacrylate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium polyacrylate. 173.73 Section 173.73 Food and... Substances and Polymer Adjuvants for Food Treatment § 173.73 Sodium polyacrylate. Sodium polyacrylate (CAS... of Weight Average and Number Average Molecular Weight of Sodium Polyacrylate,” which is...

  7. A Patient with MSUD: Acute Management with Sodium Phenylacetate/Sodium Benzoate and Sodium Phenylbutyrate

    OpenAIRE

    Melis Köse; Ebru Canda; Mehtap Kagnici; Sema Kalkan Uçar; Mahmut Çoker

    2017-01-01

    In treatment of metabolic imbalances caused by maple syrup urine disease (MSUD), peritoneal dialysis, and hemofiltration, pharmacological treatments for elimination of toxic metabolites can be used in addition to basic dietary modifications. Therapy with sodium phenylacetate/benzoate or sodium phenylbutyrate (NaPB) in urea-cycle disorder cases has been associated with a reduction in branched-chain amino acid (BCAA) concentrations when the patients are on adequate dietary protein intake. Moreo...

  8. Treprostinil sodium Pharmacia.

    Science.gov (United States)

    Chattaraj, Sarat C

    2002-04-01

    United Therapeutics Corp (UTC) is developing treprostinil sodium (Remodulin, UT-15), a stable structural analog of prostacyclin, for the potential treatment of primary pulmonary (arterial) hypertension (PAH), peripheral vascular disease (PVD) and other cardiovascular conditions [327593], including critical limb ischemia (CLI) [412483]. In August 2000, UTC submitted the initial, non-clinical sections of an NDA for the treatment of pulmonary hypertension [378906]. Treprostinil, which had previously been designated as an Orphan Drug, was also awarded Priority Review status by the US FDA in October 2000 [385864], [386271]. In December 2000, UTC agreed with the FDA that the NDA for treprostinil did not need to be presented to the Cardiovascular and Renal Drugs Advisory Committee, which was expected to allow UTC and the FDA to work towards the 6-month Priority Review timeline [393888]. On August 9, 2001, the advisory committee recommended approval of treprostinil and UTC refiled the NDA on the same day [418682]. In February 2002, the FDA issued an approvable letter for treprostinil injection for the treatment of PAH. The FDA proposed drug labeling for PAH consistent with the treatment of both primary and secondary pulmonary hypertension in patients with New York Heart Association (NYHA) Class II-IV symptoms. The approvable letter also stated that the FDA intended to approve treprostinil with a requirement that UTC subsequently conduct a post-marketing controlled clinical trial to verify and further describe the drug's clinical benefit [439278]. In February 2001, UTC submitted a marketing authorization application (MAA) in France for approval of treprostinil for the treatment of PAH. Upon approval of the MAA, UTC planned to file for Mutual Recognition in other European countries and was also preparing similar submissions to non-European countries [391986], [397958]. By early 2001, phase II trials of treprostinil for the treatment of CLI were underway [412483]. In March

  9. Sodium Velocity Maps on Mercury

    Science.gov (United States)

    Potter, A. E.; Killen, R. M.

    2011-01-01

    The objective of the current work was to measure two-dimensional maps of sodium velocities on the Mercury surface and examine the maps for evidence of sources or sinks of sodium on the surface. The McMath-Pierce Solar Telescope and the Stellar Spectrograph were used to measure Mercury spectra that were sampled at 7 milliAngstrom intervals. Observations were made each day during the period October 5-9, 2010. The dawn terminator was in view during that time. The velocity shift of the centroid of the Mercury emission line was measured relative to the solar sodium Fraunhofer line corrected for radial velocity of the Earth. The difference between the observed and calculated velocity shift was taken to be the velocity vector of the sodium relative to Earth. For each position of the spectrograph slit, a line of velocities across the planet was measured. Then, the spectrograph slit was stepped over the surface of Mercury at 1 arc second intervals. The position of Mercury was stabilized by an adaptive optics system. The collection of lines were assembled into an images of surface reflection, sodium emission intensities, and Earthward velocities over the surface of Mercury. The velocity map shows patches of higher velocity in the southern hemisphere, suggesting the existence of sodium sources there. The peak earthward velocity occurs in the equatorial region, and extends to the terminator. Since this was a dawn terminator, this might be an indication of dawn evaporation of sodium. Leblanc et al. (2008) have published a velocity map that is similar.

  10. Methods to Compose Sodium Fire Extinguishing Equipment on Sodium Test Facility

    Energy Technology Data Exchange (ETDEWEB)

    Kim, B. H.; Kim, J. M.; Jeong, J. Y.; Choi, B. H

    2008-06-15

    Sodium fire is graded 'D' and it is difficult to extinguish sodium fire. In this report, the characteristics of sodium fire and the methods composing the suitable fire extinguishing systems to suppress fire effectively were described.

  11. Clinical experience with pegaptanib sodium

    Directory of Open Access Journals (Sweden)

    Chiara Rosina

    2008-10-01

    Full Text Available Chiara Rosina, Ferdinando Bottoni, Giovanni StaurenghiLuigi Sacco Hospital, University of Milano, ItalyAbstract: Pegaptanib sodium (Macugen® blocks the extracellular vascular endothelial growth factor (VEGF isoform VEGF165, whose elevated levels are associated with the development of choroidal neovascularization (CNV. This selective inhibition prevents binding to the VEGF receptors and the development of the increased vascular permeability and the CNV associated with neovascular age-related degeneration (AMD. The VEGF Inhibition Study In Ocular Neovascularization (VISION demonstrated that pegaptanib sodium confers clinically meaningful benefit in the treatment of all angiographic subtypes of neovascular AMD. It also has a favorable safety profile after 1 and 2 years of continuous treatment, and recent data suggest that the agent has a disease-modifying effect. Post hoc analysis of VISION suggests that treatment benefit may be greatest in patients with early lesions, in whom 80% achieved the primary endpoint of <15 letters lost, 47% maintained visual acuity (VA, and 20% gained ≥15 letters of vision. Similarly, our own clinical experience indicates that pegaptanib sodium achieves better outcomes in early lesions than in established lesions, particularly in patients with previously untreated minimally classic and occult lesions in whom VA improvement and lesion size stabilization has been recorded. Observations indicate that pegaptanib sodium has a slower mode of action than unselective VEGF inhibitors, resulting in an average of 3–4 injections being required to stabilize VA and lesion size. Pegaptanib sodium has good efficacy and safety profiles and represents a good treatment option for patients with early CNV membranes associated with neovascular AMD.Keywords: vascular endothelial growth factor (VEGF, choroidal neovasularization (CNV, age-related macular degeneration (AMD, pegaptanib sodium, early lesions, visual acuity (VA

  12. Too Much Sodium PSA (:60)

    Centers for Disease Control (CDC) Podcasts

    2012-02-07

    This 60 second PSA is based on the February 2012 CDC Vital Signs report. Ninety percent of Americans age two and older eat too much sodium which can increase your risk for high blood pressure and often leads to heart disease and stroke, two leading causes of death in the US. Learn several small steps you can take to reduce the amount of sodium in your diet.  Created: 2/7/2012 by Centers for Disease Control and Prevention (CDC).   Date Released: 2/7/2012.

  13. Contact allergy to sodium sulfite and its relationship to sodium metabisulfite.

    Science.gov (United States)

    Oliphant, Thomas; Mitra, Angana; Wilkinson, Mark

    2012-03-01

    Sulfites are in widespread use as preservatives/antioxidants. There is increasing recognition of allergic contact dermatitis caused by sodium metabisulfite; however, contact allergy to sodium sulfite is less well recognized. We sought to establish the prevalence of positive patch test reactions to sodium sulfite in our patient population and investigate its relationship with sodium metabisulfite. Over a 4-month period, 183 patients referred for patch testing were tested with sodium sulfite 1% pet. in addition to sodium metabisulfite 1% pet., which already forms part of our baseline series. Positive allergic reactions occurred to sodium metabisulfite in 5.5% of the tested patients and to sodium sulfite in 3.8% of the tested patients. Sixty per cent of patients with a positive reaction to sodium metabisulfite were positive to sodium sulfite. Only 1 patient (0.6%) with a negative reaction to sodium metabisulfite showed a positive reaction to sodium sulfite. This study shows that the majority of patients with positive reactions to sodium metabisulfite are also positive to sodium sulphite. Routinely patch testing with sodium sulfite is probably unnecessary, as most patients with positive reactions will also react to sodium metabisulfite. Clinicians should consider advising patients to avoid sodium sulfite and other sulfites when a positive allergic reaction to sodium metabisulfite occurs. © 2012 John Wiley & Sons A/S.

  14. Dietary Sodium Intake in Type 2 Diabetes.

    Science.gov (United States)

    Provenzano, Laura Ferreira; Stark, Sue; Steenkiste, Ann; Piraino, Beth; Sevick, Mary Ann

    2014-07-01

    Patients with type 2 diabetes have an increased risk for cardiovascular and chronic kidney disease. Superimposed hypertension further increases the risk and is associated with increased dietary sodium intake. There are few data available on dietary sodium intake in type 2 diabetes. The aim of this study was to quantify dietary sodium intake in a cohort of self-referred patients with type 2 diabetes and to identify sociodemographic characteristics associated with it. Sodium intake in this cohort was far greater than current recommendations. Increased awareness of sodium intake in this population might lead to target interventions to reduce sodium intake and potentially improve long-term outcomes.

  15. Effects of temperature and sodium carboxylate additives on mineralization of calcium oxalate in silica gel systems

    Institute of Scientific and Technical Information of China (English)

    OUYANG; Jianming; DENG; Suiping; LI; Xiangping; TAN; Yanh

    2004-01-01

    [1]Ouyang, J. M., Yao, X. Q., Su, Z. X. et al., Simulation of calcium oxalate stone in Vitro, Science in China, Ser. B, 2003, 46(3):234-242.[2]Xu, S. H., Chen, J. Q., Zhou, H., Nepidemiological study of renal calculus in Shenshen region, Chin. J. Urol. (in Chinese), 1999,20(11): 655-657.[3]Bretherton, T., Rodgers, A., Crystallization of calcium oxalate in minimally diluted urine, J. Crystal Growth, 1998, 192: 448-455.[4]Grover, P. K., Ryall, R. L., Effect of seed crystals of uric acid and monosodium urate on the crystallization of CaOxa in undiluted human urine in vitro, Clin. Sci., 1997, 92: 205-213.[5]Laube, N., Mohr, B., Hesse, A., Laser-probe-based investigation of the evolution of particle size distributions of calcium oxalate particles formed in artificial urines, J. Crystal Growth, 2001, 233:367-374.[6]Tunik, L., Fueredi-Milhofer, H., Garti, N., Adsorption of sodium diisooctyl sulfosuccinate onto calcium oxalate crystals, Langmuir,1998, 14: 3351-3355.[7]Cody, A. M., Cody, R. D., Calcium oxalate trihydrate phase control by structurally-specific carboxylic acids, J. Cryst. Growth,1994, 135: 234-245.[8]Ouyang, J. M., Duan, L., Tieke, B., Effects of carboxylic acids on the crystal growth of calcium oxalate nanoparticles in lecithin-water liposome systems, Langmuir, 2003, 19: 8980-8985.[9]Guo, S., Ward, M. D., Wesson, J. A., Direct visualization of calcium oxalate monohydrate crystallization and dissolution with atomic force microscopy and the role of polymeric additives,Langmuir, 2002, 18:4284-4291.[10]Yasui, T., Sato, M., Fujita, K., Effects of citrate on renal stone formation and osteopontin expression in a rat urolithiasis model,Urol. Res., 2001,29: 50-56.[11]Ouyang, J. M., Deng, S. P., Controlled and uncontrolled crystallization of calcium oxalate monohydrate in the presence of citric acid, Dalton Transactions, 2003, (14): 2846-2851.[12]Khan, S. R., Whalen, P. O., Glenton, P. A., Heterogeneous nucleation of

  16. 40 CFR 437.26 - Pretreatment standards for new sources (PSNS).

    Science.gov (United States)

    2010-07-01

    ...) EFFLUENT GUIDELINES AND STANDARDS THE CENTRALIZED WASTE TREATMENT POINT SOURCE CATEGORY Oils Treatment and...: Standards for chromium, cobalt, copper, lead, tin, zinc, carbazole, n-decane, bis(2-ethylhexyl)...

  17. 40 CFR 469.22 - Specialized definitions.

    Science.gov (United States)

    2010-07-01

    ... methylene chloride naphthalene 2 Nitrophenol phenol bis (2-ethylhexyl) phthalate tetrachloroethylene toluene... crystals” means the growing of crystals and/or the production of crystal wafers for use in the manufacture...

  18. Phthalate Intakes

    Data.gov (United States)

    U.S. Environmental Protection Agency — Compilation of literature-reported intake values of phthalates; specifically dibutyl phthalate (DBP), bis(2-ethylhexyl) phthalate, and diisononyl phthalate (DiNP)....

  19. Borocaptate sodium (BSH) toxicity issues

    Energy Technology Data Exchange (ETDEWEB)

    LaHann, T.

    1995-11-01

    ISU`s Center for Toxicology Research has been conducting toxicity testing of borocaptate sodium (BSH) to aid in assessing if proposed human studies of BSH are likely to be acceptably safe. This report describes BSH interactions with other biological agents.

  20. Spectra of sodium aluminate solutions

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The UV spectra of sodium aluminate solutions were obtained in the sodium oxide concentration range from 59 to 409 g/L and the caustic ratio range from 1.5 to 4.0 to reveal the structure characteristics of them. It is found that a new peak appears at about 370 nm besides peaks at about 220 and 266 nm in all solutions. The new peak is strongly favored by high hydroxide concentration and high caustic ratio. And it only appears when the solutions are prepared by dissolving sodium hydroxide and aluminum hydroxide.In addition, the IR and Raman spectra of sodium aluminate solutions with high alkali concentration and high caustic ratio were measured, and the UV spectra of aqueous solutions of Al(H2O)63+ and AlF63- were measured as well. According to the crystal field theory in coordination chemistry as well as the above spectra characteristics, this new peak at about 370 nm is determined as the evidence of a new species of aluminate ion with a coordination number of 6.

  1. Urinary Sodium and Potassium Excretion and Dietary Sources of Sodium in Maputo, Mozambique.

    Science.gov (United States)

    Queiroz, Ana; Damasceno, Albertino; Jessen, Neusa; Novela, Célia; Moreira, Pedro; Lunet, Nuno; Padrão, Patrícia

    2017-08-03

    This study aimed to evaluate the urinary excretion of sodium and potassium, and to estimate the main food sources of sodium in Maputo dwellers. A cross-sectional evaluation of a sample of 100 hospital workers was conducted between October 2012 and May 2013. Sodium and potassium urinary excretion was assessed in a 24-h urine sample; creatinine excretion was used to exclude unlikely urine values. Food intake in the same period of urine collection was assessed using a 24-h dietary recall. The Food Processor Plus(®) was used to estimate sodium intake corresponding to naturally occurring sodium and sodium added to processed foods (non-discretionary sodium). Salt added during culinary preparations (discretionary sodium) was computed as the difference between urinary sodium excretion and non-discretionary sodium. The mean (standard deviation) urinary sodium excretion was 4220 (1830) mg/day, and 92% of the participants were above the World Health Organization (WHO) recommendations. Discretionary sodium contributed 60.1% of total dietary sodium intake, followed by sodium from processed foods (29.0%) and naturally occurring sodium (10.9%). The mean (standard deviation) urinary potassium excretion was 1909 (778) mg/day, and 96% of the participants were below the WHO potassium intake recommendation. The mean (standard deviation) sodium to potassium molar ratio was 4.2 (2.4). Interventions to decrease sodium and increase potassium intake are needed in Mozambique.

  2. Urinary Sodium and Potassium Excretion and Dietary Sources of Sodium in Maputo, Mozambique

    Directory of Open Access Journals (Sweden)

    Ana Queiroz

    2017-08-01

    Full Text Available This study aimed to evaluate the urinary excretion of sodium and potassium, and to estimate the main food sources of sodium in Maputo dwellers. A cross-sectional evaluation of a sample of 100 hospital workers was conducted between October 2012 and May 2013. Sodium and potassium urinary excretion was assessed in a 24-h urine sample; creatinine excretion was used to exclude unlikely urine values. Food intake in the same period of urine collection was assessed using a 24-h dietary recall. The Food Processor Plus® was used to estimate sodium intake corresponding to naturally occurring sodium and sodium added to processed foods (non-discretionary sodium. Salt added during culinary preparations (discretionary sodium was computed as the difference between urinary sodium excretion and non-discretionary sodium. The mean (standard deviation urinary sodium excretion was 4220 (1830 mg/day, and 92% of the participants were above the World Health Organization (WHO recommendations. Discretionary sodium contributed 60.1% of total dietary sodium intake, followed by sodium from processed foods (29.0% and naturally occurring sodium (10.9%. The mean (standard deviation urinary potassium excretion was 1909 (778 mg/day, and 96% of the participants were below the WHO potassium intake recommendation. The mean (standard deviation sodium to potassium molar ratio was 4.2 (2.4. Interventions to decrease sodium and increase potassium intake are needed in Mozambique.

  3. Drug: D00305 [KEGG MEDICUS

    Lifescience Database Archive (English)

    Full Text Available MENTARY TRACT AND METABOLISM A06 DRUGS FOR CONSTIPATION A06A DRUGS FOR CONSTIPATION A06AA Softeners, emoll...ients A06AA02 Docusate sodium D00305 Dioctyl sodium sulfosuccinate (JAN); Docusate

  4. Sodium Balance During Extra Corporeal Dialysis

    Directory of Open Access Journals (Sweden)

    Locatelli Francesco

    2001-01-01

    Full Text Available In order to reduce intradialytic and interdialytic morbidity, it is important to obtain a zero sodium balance at the end of each dialysis session. This can be achieved by matching exactly the interdialytic sodium and water intake with the intradialytic sodium and water removal. A positive sodium balance can be obtained by using hypernatric dialysis or "sodium ramping" or convective techniques. While reducing the intradialytic side effects (hypotension, cramps, nausea, vomiting, these methods may increase the interdialytic side effects (thirst, weight gain, hypertension and pulmonary edema. Given the highly variable amounts of sodium introduced during the interdialytic periods, the use of sodium-conductivity kinetic models allows removing exactly the amount of sodium accumulated in the interdialytic period. This strategy may be advantageous towards cardiovascular stability in patients prone to dialysis hypotension.

  5. Solar control of sodium escape from Io

    National Research Council Canada - National Science Library

    Grava, Cesare; Schneider, Nicholas M; Leblanc, François; Morgenthaler, Jeffrey P; Mangano, Valeria; Barbieri, Cesare

    2014-01-01

    We report ground‐based spectroscopic observations of the Io sodium cloud before and after eclipse by Jupiter, in a search for possible effects of sunlight on the total atomic sodium content in Io's exosphere...

  6. 21 CFR 186.1750 - Sodium chlorite.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium chlorite. 186.1750 Section 186.1750 Food and... Substances Affirmed as GRAS § 186.1750 Sodium chlorite. (a) Sodium chlorite (NaCLO2, CAS Reg. No. 7758-19-2... into a solution of sodium hydroxide and hydrogen peroxide. (b) the ingredient is used at levels from...

  7. 21 CFR 184.1751 - Sodium citrate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium citrate. 184.1751 Section 184.1751 Food and... Substances Affirmed as GRAS § 184.1751 Sodium citrate. (a) Sodium citrate (C6H5Na3O7·2H2O, CAS Reg. No. 68... may be prepared in an anhydrous state or may contain two moles of water per mole of sodium citrate....

  8. Dietary Sodium Intake in Type 2 Diabetes

    OpenAIRE

    Provenzano, Laura Ferreira; Stark, Sue; Steenkiste, Ann; Piraino, Beth; Sevick, Mary Ann

    2014-01-01

    Patients with type 2 diabetes have an increased risk for cardiovascular and chronic kidney disease. Superimposed hypertension further increases the risk and is associated with increased dietary sodium intake. There are few data available on dietary sodium intake in type 2 diabetes. The aim of this study was to quantify dietary sodium intake in a cohort of self-referred patients with type 2 diabetes and to identify sociodemographic characteristics associated with it. Sodium intake in this coho...

  9. Normal range of human dietary sodium intake

    DEFF Research Database (Denmark)

    McCarron, David A; Kazaks, Alexandra G; Geerling, Joel C

    2013-01-01

    The recommendation to restrict dietary sodium for management of hypertensive cardiovascular disease assumes that sodium intake exceeds physiologic need, that it can be significantly reduced, and that the reduction can be maintained over time. In contrast, neuroscientists have identified neural...... circuits in vertebrate animals that regulate sodium appetite within a narrow physiologic range. This study further validates our previous report that sodium intake, consistent with the neuroscience, tracks within a narrow range, consistent over time and across cultures....

  10. 21 CFR 582.3731 - Sodium ascorbate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium ascorbate. 582.3731 Section 582.3731 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL....3731 Sodium ascorbate. (a) Product. Sodium ascorbate. (b) Conditions of use. This substance...

  11. 21 CFR 182.3731 - Sodium ascorbate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium ascorbate. 182.3731 Section 182.3731 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Sodium ascorbate. (a) Product. Sodium ascorbate. (b) Conditions of use. This substance is...

  12. 21 CFR 182.1778 - Sodium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium phosphate. 182.1778 Section 182.1778 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Substances § 182.1778 Sodium phosphate. (a) Product. Sodium phosphate (mono-, di-, and tribasic)....

  13. 21 CFR 582.6778 - Sodium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium phosphate. 582.6778 Section 582.6778 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Sodium phosphate. (a) Product. Sodium phosphate (mono-, di-, and tribasic). (b) Conditions of use....

  14. 21 CFR 582.1778 - Sodium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium phosphate. 582.1778 Section 582.1778 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1778 Sodium phosphate. (a) Product. Sodium phosphate (mono-, di-, and tribasic)....

  15. 21 CFR 582.5778 - Sodium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium phosphate. 582.5778 Section 582.5778 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Supplements 1 § 582.5778 Sodium phosphate. (a) Product. Sodium phosphate (mono-, di-, and tribasic)....

  16. 21 CFR 178.3900 - Sodium pentachlorophenate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium pentachlorophenate. 178.3900 Section 178... SANITIZERS Certain Adjuvants and Production Aids § 178.3900 Sodium pentachlorophenate. Sodium pentachlorophenate may be safely used as a preservative for ammonium alginate employed as a processing aid in the...

  17. 21 CFR 522.1145 - Hyaluronate sodium.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Hyaluronate sodium. 522.1145 Section 522.1145 Food... Hyaluronate sodium. (a)(1) Specifications. Each milliliter of sterile aqueous solution contains 10 milligrams of hyaluronate sodium. (2) Sponsor. See 000009 in § 510.600(c). (3) Conditions of use—(i)...

  18. 21 CFR 526.365 - Cephapirin sodium.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Cephapirin sodium. 526.365 Section 526.365 Food... DRUGS, FEEDS, AND RELATED PRODUCTS INTRAMAMMARY DOSAGE FORMS § 526.365 Cephapirin sodium. (a) Specifications. Each 10-milliliter dose contains 200 milligrams of cephapirin sodium activity in a peanut-oil...

  19. Mixed Solvent Reactive Recrystallization of Sodium Carbonate

    NARCIS (Netherlands)

    Gaertner, R.S.

    2005-01-01

    Investigation of the reactive recrystallization of trona (sodium sesquicarbonate) and sodium bicarbonate to sodium carbonate (soda) in a mixed solvent led to the design of several alternative, less energy consumptive, economically very attractive process routes for the production of soda from all pr

  20. 21 CFR 558.60 - Arsanilate sodium.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Arsanilate sodium. 558.60 Section 558.60 Food and... in Animal Feeds § 558.60 Arsanilate sodium. (a) Appprovals. Type A medicated articles: 20, 50, or 100...) Arsanilate sodium may be used in accordance with the provisions of this section in the combinations...

  1. 21 CFR 556.620 - Sulfabromomethazine sodium.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sulfabromomethazine sodium. 556.620 Section 556... Tolerances for Residues of New Animal Drugs § 556.620 Sulfabromomethazine sodium. Tolerances for residues of sulfabromomethazine sodium in food are established as follows: (a) In the uncooked edible tissues of cattle at...

  2. Polymorphism of Metallic Sodium under Nanoconfinement.

    Science.gov (United States)

    Uskov, A V; Nefedov, D Yu; Charnaya, E V; Haase, J; Michel, D; Kumzerov, Yu A; Fokin, A V; Bugaev, A S

    2016-01-13

    (23)Na NMR studies of sodium nanoparticles confined to porous glass with the 3.5 nm mean pore size were carried out. The emergence of the second component of the NMR line was observed below 240 K that evidences the occurrence of another modification of metallic sodium. The phase transition temperature is much higher than the martensite transformation temperature in bulk sodium.

  3. 21 CFR 582.6751 - Sodium citrate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium citrate. 582.6751 Section 582.6751 Food and..., FEEDS, AND RELATED PRODUCTS SUBSTANCES GENERALLY RECOGNIZED AS SAFE Sequestrants 2 § 582.6751 Sodium citrate. (a) Product. Sodium citrate. (b) Conditions of use. This substance is generally recognized...

  4. 21 CFR 582.1751 - Sodium citrate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium citrate. 582.1751 Section 582.1751 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS....1751 Sodium citrate. (a) Product. Sodium citrate. (b) Conditions of use. This substance is...

  5. Sodium: How to Tame Your Salt Habit

    Science.gov (United States)

    ... sodium than are luncheon meat, bacon, hot dogs, sausage and ham. Buy fresh or frozen poultry or ... ducing-Sodium-in-a-Salty-World_UCM_457519_Article.jsp#.VuD81cfAju8. Accessed March 10, 2016. Sodium: Tips ...

  6. The influence of moderate reduction in dietary sodium on human salivary sodium concentration.

    Science.gov (United States)

    Christensen, C M; Bertino, M; Beauchamp, G K; Navazesh, M; Engelman, K

    1986-01-01

    Twenty-four healthy subjects were placed for 12-13 weeks on diets that reduced average sodium intake from 145 to 74 m-equiv. Na+/day as determined by multiple 24-h urine collections before and during the diet. Whole-mouth resting and stimulated saliva was collected and analysed for flow rate and sodium concentration several times before and during the low-sodium period. Sodium restriction did not influence salivary flow rates but salivary sodium levels fell 25 per cent for resting and 17 per cent for stimulated saliva. Thus moderate reductions in sodium intake are accompanied by significantly lower salivary sodium levels.

  7. CDC Vital Signs: Reducing Sodium in Children's Diets

    Science.gov (United States)

    ... foods sold and served in schools that will reduce sodium up to 50% by 2022. Reducing sodium intake ... have already made efforts to reduce added sodium. Replace sodium with alternatives like spices, herbs, and vegetables. Shop ...

  8. Sodium intake and dietary sources of sodium in undergraduate students from Novi Sad, Serbia

    OpenAIRE

    Jovičić-Bata Jelena; Grujičić Maja; Rađen Slavica; Novaković Budimka

    2016-01-01

    Background/Aim. Data on sodium intake and sources of sodium in the diet in Serbia are limited. The aim of this study was to estimate the sodium intake and identify the sources of sodium in the diet of undergraduate students attending the University of Novi Sad. Methods. Students completed a questionnaire to gather data on their gender, age and university faculty attended, and then a 24 h dietary recall. The sodium intake of the students was calculated using...

  9. Stability of Ranitidine Hydrochloride with Cefazolin Sodium, Cefbuperazone Sodium, Cefoxitin Sodium and Cephalothin Sodium during Simulated Y-Site Administration.

    Science.gov (United States)

    Inagaki, K; Miyamoto, Y; Kurata, N; Nakane, S; Gill, M A; Nishida, M

    2000-01-01

    The compatibility and stability of ranitidine hydrochloride when comixed with four cephalosporins (cefazolin sodium, cefoxitin sodium, cephalothin sodium and cefbuperazone sodium) during simulated Y-site injection were studied. The mixtures were prepared by mixing equal volumes (2 mL) of ranitidine hydrochloride (1mg/mL) and each tested cephalosporin (20 mg/mL) in a 10 mL glass test tube. All study mixtures were prepared in triplicate and stored at room temperature under normal fluorescent room lighting. The physical appearaance and pH of each mixture were recorded; the chemical stability of each drug was immediatedly determined by stability-indicating high-performance liquid chromatography from samples stored for up to four hours after mixing. Stability was defined as the retention of more than 90% of the initial concentration of each drug. Visual inspection revealed no color or clarity change and the pH changes were less than 0.2 pH units in the tested mixtures for cefazolin and cefoxitin: however, there were significant pH changes for cefbuperazone and cephalothin after four hours of storage. Ranitidine retained greater than 90% of its original concentration within the tested period in the mixture with 20 mg/mL of each tested cephalosporin, except for cephalothin (86.6% of control). In the presence of 10 mg/mL cephalothin, however, ranitidine retained greater than 90% for four hours. Meanwhile, all four cephalosporins retained greater than 90% of their original concentrations for up to four hours in the mixture with ranitidine. From the results obtained, it is clear that ranitidine solution may be coadministered with a solution of either cefazolin, cefoxitin or cefbuperazone during Y-site administration for up to four hours after mxining. On the other hand, since ranitidine with cephalothin (20 mg/mL) fell below 90%, the amount of cephalothin should not exceed 10 mg/mL when coadminstered with ranitidine solution.

  10. Sodium cromoglycate in nocturnal asthma.

    OpenAIRE

    1986-01-01

    To investigate whether mast cell degranulation was important in producing nocturnal asthma, the effect of a single high dose of nebulised sodium cromoglycate on overnight bronchoconstriction, oxygen saturation, and breathing patterns in eight patients with nocturnal wheeze was examined. The study took the form of a double blind placebo controlled crossover comparison. Treatment with cromoglycate did not reduce the overnight fall in FEV1 or FVC, although it was associated with improved nocturn...

  11. Enhancement of Aminoacylase Activity by Sodium Citrate

    Institute of Scientific and Technical Information of China (English)

    于范利; 曹志方; 李森; 周海梦

    2001-01-01

    Kidney and other tissues of animals and humans have a high concentration of citrate which is an important intermediate substance in the citrate cycle. Citrate may play an important physiological role in metabolism. In this paper, we studied the interaction of the sodium salt of citrate with aminoacylase which is an important enzyme in metabolism and found sodium citrate can enhance the activity of aminoacylase. The maximum enzyme activity induced by sodium citrate increased approximately 3 folds over the enzyme activity without sodium citrate. The initial reaction rates (Ⅴ) for different concentrations of sodium citrate were obtained, showing that sodium citrate is a non-competitive activator. The result of the ANS binding fluorescence measurements for aminoacylase indicated that increasing sodium citrate concentrations markedly increased the ANS binding fluorescence with a blue shift of the emission spectra peak. This suggests the formation of more hydrophobic regions. Aggregates formed quickly when aminoacylase was incubated with sodium citrate (0.3 mol/L) and guanidinium chloride (0- 3. 5 mol/L). Aminoacylase lost enzyme activity in the guanidinium chloride more quickly in the presence of sodium citrate than in the absence of sodium citrate. The intrinsic fluorescence emission intensity decreased more quickly and the red shift of the emission spectra peak was larger than that without sodium citrate.

  12. [Sodium determination in biological fluids].

    Science.gov (United States)

    Cristol, J-P; Balint, B; Canaud, B; Daurés, M-F

    2007-09-01

    Electrolyte disorders are frequently observed in nephrology and intensive care unit department and Na determination is routinely performed in biochemistry laboratories. Three methods are currently available. Flame photometry remains the reference method. With this method the serum sample is diluted before the actual measurement is obtained. Results are expressed as molarity (per Liter of plasma). Potentiometric methods have an increasing importance due to the advances in ion sensitive (selective) electrodes (ISE). Whereas the instruments for routine chemical analysis typically use indirect potentiometry (involving te dilution of samples) to measure sodium levels, the equipment for measuring arterial blood gases use direct potentiometry without any dilution. Thus, results obtained with indirect potentiometry are expressed in molarity (per liter of plasma) while results obtained with direct potentiometry are initially given in morality (per kg of plasma water) then converted in molarity. Analytical performances are in all cases satisfactory and therefore all the methods could be used in both normal and pathological ranges. Methods involving sample dilution such as flame photometry or indirect potentiometry, the serum sodium value would be expected to be low in case of decrease plasma water (pseudohyponatremia). By contrast, with direct potentiometry where no sample dilution takes place, no interference would be expected since the activity of sodium in the water phase only is being measured. Thus, the classical pseudohyponatremia observed with hyperlipemia or paraproteinemia are not further observed with direct potentiometry. These differences in methodology should be taken into account to explain discrepancies between results obtained with classical biochemistry analyser and with blood gas apparatus.

  13. Compared With Usual Sodium Intake, Low- and Excessive-Sodium Diets Are Associated With Increased Mortality

    DEFF Research Database (Denmark)

    Graudal, Niels; Jürgens, Gesche; Baslund, Bo

    2014-01-01

    BACKGROUND: The effect of sodium intake on population health remains controversial. The objective was to investigate the incidence of all-cause mortality (ACM) and cardiovascular disease events (CVDEs) in populations exposed to dietary intakes of low sodium (sodium (low usual...... sodium: 115-165 mmol; high usual sodium: 166-215 mmol), and high sodium (>215 mmol). METHODS: The relationship between individual measures of dietary sodium intake vs. outcome in cohort studies and randomized controlled trials (RCTs) measured as hazard ratios (HRs) were integrated in meta......-analyses. RESULTS: No RCTs in healthy population samples were identified. Data from 23 cohort studies and 2 follow-up studies of RCTs (n = 274,683) showed that the risks of ACM and CVDEs were decreased in usual sodium vs. low sodium intake (ACM: HR = 0.91, 95% confidence interval (CI) = 0.82-0.99; CVDEs: HR = 0...

  14. Effects of sodium cromoglycate and nedocromil sodium on histamine secretion from human lung mast cells.

    Science.gov (United States)

    Leung, K B; Flint, K C; Brostoff, J; Hudspith, B N; Johnson, N M; Lau, H Y; Liu, W L; Pearce, F L

    1988-01-01

    Sodium cromoglycate and nedocromil sodium produced a dose dependent inhibition of histamine secretion from human pulmonary mast cells obtained by bronchoalveolar lavage and by enzymatic dissociation of lung parenchyma. Both compounds were significantly more active against the lavage cells than against the dispersed lung cells, and nedocromil sodium was an order of magnitude more effective than sodium cromoglycate against both cell types. Tachyphylaxis was observed with the parenchymal cells but not with the lavage cells. Nedocromil sodium and sodium cromoglycate also inhibited histamine release from the lavage cells of patients with sarcoidosis and extrinsic asthma. PMID:2462755

  15. Organic electrolytes for sodium batteries

    Science.gov (United States)

    Vestergaard, B.

    1992-09-01

    A summary of earlier given status reports in connection with the project on organic electrolytes for sodium batteries is presented. The aim of the investigations was to develop new room temperature molten salts electrolytes mainly with radical substituted heterocyclic organic chlorides mixed with aluminum chloride. The new electrolytes should have an ionic conductivity comparable with MEIC1:AlCl3 or better. A computer model program MOPAC (Molecular Orbital Package) was to be included to calculate theoretically reduction potentials for a variety of organic cations. Furthermore, MOPAC could be utilized to predict the electron densities, and then give a prediction of the stability of the organic cation.

  16. Sodium cacodylate as antimitotic agent

    Directory of Open Access Journals (Sweden)

    Jadwiga A. Tarkowska

    2014-01-01

    Full Text Available The effect of pure sodium cacodylate on dividing cells was studied. The root meristematic cells of Allium cepa L. (the roots were squashed in acetoorcein and endosperm cells of Haemanthus katherinae Bak. (in vitro observations were used. Serious disturbances in karyokinesis and cytokinesis were found that led most often to the formation of polyploid or multinucleate (A. cepa cells. These results point to damage of the mitotic spindle and phragmoplast. Careful use of cacodylate buffer in ultrastructural studies of microtubules is advised.

  17. Sodium cromoglycate in nocturnal asthma.

    Science.gov (United States)

    Morgan, A D; Connaughton, J J; Catterall, J R; Shapiro, C M; Douglas, N J; Flenley, D C

    1986-01-01

    To investigate whether mast cell degranulation was important in producing nocturnal asthma, the effect of a single high dose of nebulised sodium cromoglycate on overnight bronchoconstriction, oxygen saturation, and breathing patterns in eight patients with nocturnal wheeze was examined. The study took the form of a double blind placebo controlled crossover comparison. Treatment with cromoglycate did not reduce the overnight fall in FEV1 or FVC, although it was associated with improved nocturnal oxygenation. This study suggests that mast cell degranulation may not be important in the pathogenesis of nocturnal asthma. PMID:3085257

  18. Sodium intake and dietary sources of sodium in undergraduate students from Novi Sad, Serbia

    Directory of Open Access Journals (Sweden)

    Jovičić-Bata Jelena

    2016-01-01

    Full Text Available Background/Aim. Data on sodium intake and sources of sodium in the diet in Serbia are limited. The aim of this study was to estimate the sodium intake and identify the sources of sodium in the diet of undergraduate students attending the University of Novi Sad. Methods. Students completed a questionnaire to gather data on their gender, age and university faculty attended, and then a 24 h dietary recall. The sodium intake of the students was calculated using the dietary recall data and data on the sodium content of foods. The contribution of different food groups as well as of specific foodstuffs to the total sodium intake was calculated. Results. The mean estimated sodium intake of the students was 3,938.5 ± 1,708.1 mg/day. The sodium intake of 89.1% of the surveyed students exceeded the guideline for sodium intake, the majority of the sodium coming from processed foods (78.9% of the total sodium intake. The food groups that contributed the most to the total sodium intake of the students were meat and meat products (21.7% and cereals and cereal-based products (18.6%. Bread and other bakery products were responsible for 13.1% of the total sodium intake. Conclusion. High sodium intake in students of the University of Novi Sad puts them at high risk of developing high blood pressure. The food industry should work towards reformulating products with high sodium content, especially bread and other bakery products. Efforts should be taken to reduce sodium intake among undergraduate students in Novi Sad.

  19. Parametric Effect of Sodium Hydroxide and Sodium Carbonate on the Potency of a Degreaser

    Directory of Open Access Journals (Sweden)

    Babatope Abimbola Olufemi

    2016-01-01

    Full Text Available Normal 0 false false false EN-US X-NONE X-NONE Experimental and statistical analysis was carried out on the comparative effect of sodium hydroxide and sodium carbonate on the potency of a laboratory produced degreaser in this work. The materials used include; octadecyl benzene sulphonic acid, sodium hydroxide, sodium carbonate, sodium metasilicate, carboxyl methyl cellulose (C.M.C, formadelhyde, perfume, colourant and distilled water. Different samples of degreaser were produced with varying composition of sodium hydroxide and sodium carbonate respectively. Statistical significance through methods like analysis of variance (ANOVA of some parameters on various concentrations of sodium hydroxide and sodium carbonate was investigated. The effect of the varying compositions of sodium hydroxide and sodium carbonate was also determined by using a gray scale (GS test, and also subjecting surfaces heavily stained with crude oil to determine and characterize the cleansing action of the degreaser. It was found that as the concentration of sodium hydroxide increases, the cleansing ability also increases, whereas the increase in concentration of sodium carbonate had no effect on the cleansing ability. The work would enable production of effective, useful and property controlled degreasers at moderate cost.

  20. Reduced Dietary Sodium Intake Increases Heart Rate

    DEFF Research Database (Denmark)

    Graudal, Niels A; Hubeck-Graudal, Thorbjørn; Jürgens, Gesche

    2016-01-01

    Reduced dietary sodium intake (sodium reduction) increases heart rate in some studies of animals and humans. As heart rate is independently associated with the development of heart failure and increased risk of premature death a potential increase in heart rate could be a harmful side......-effect of sodium reduction. The purpose of the present meta-analysis was to investigate the effect of sodium reduction on heart rate. Relevant studies were retrieved from an updated pool of 176 randomized controlled trials (RCTs) published in the period 1973-2014. Sixty-three of the RCTs including 72 study...... populations reported data on heart rate. In a meta-analysis of these data sodium reduction increased heart rate with 1.65 beats per minute [95% CI: 1.19, 2.11], p sodium reduction...

  1. Neurotransmitter: Sodium Symporters: Caught in the Act!

    DEFF Research Database (Denmark)

    Malinauskaite, Lina

    The neurotransmitter: sodium symporters in the neurons. Communication between neurons is mediated by the release of molecules called neurotransmitters (blue dots) from first neuron and sensed by receptors on the surface of the second (purple sphere). The signal is ended by active reuptake...... of these neurotransmitters by a family of proteins called neurotransmitter: sodium symporters (NSS), which are driven using the large concentration difference of sodium (orange dots) between the outside and the inside of the cell...

  2. Diffusion coefficients in viscous sodium alginate solutions

    OpenAIRE

    Aoki, K.; Wang, B; Chen, J.; Nishiumi, T.

    2012-01-01

    Sodium alginate solution, being viscous hydrocolloid, was examined voltammetricallyin the context of viscous effects by use of a ferrocenyl compound as a redox probe.Voltammograms were almost independent of concentrations of sodium alginate even ina solid-like state. Diffusion coefficients of the ferrocenyl compound did not vary withviscosity evaluated by a viscometer. Ionic conductivity of sodium alginate was alsoindependent of the viscosity. In contrast, diffusion coefficients of the latex ...

  3. Neuronal Sodium Channels in Neurodegeneration and Neuroprotection

    Science.gov (United States)

    2002-06-01

    NIL) of the Univ Michigan. Ann Arbor Mr, USA. rat pituitary gland exhibit a 40-50% decrease in sodium current density from postnatal day 3 (P3) to...that deleted all residues beyond the tyr (gIL182STOP). Ankyrin rec of channel production may underlie the suppression of sodium current density. To...subunits con- 11 critical is for ankyrin association. Homophilic cell adhesion through 81 subunits m tributes to the suppression of melanotrope sodium

  4. The zero field self-organization of cobalt/surfactant nanocomposite thin films

    Energy Technology Data Exchange (ETDEWEB)

    Cataldo, Sebastiano; Pignataro, Bruno; Ruggirello, Angela; Liveri, Vincenzo Turco [Dipartimento di Chimica Fisica ' F. Accascina' , Universita di Palermo, Viale delle Scienze, Parco D' Orleans II, Ed 17-90128 Palermo (Italy); Bongiorno, Corrado [Istituto per la Microelectronica e Microsistemi (IMM), Stradale Primosole 50, 95121 Catania (Italy)], E-mail: bruno.pignataro@unipa.it, E-mail: a.ruggirello@unipa.it

    2009-06-03

    Cobalt nanostructures have been prepared by a chemical route based on the Co(II) reduction in the confined space of cobalt bis(2-ethylhexyl)sulfosuccinate (Co(DEHSS){sub 2}) reverse micelles dispersed in n-heptane. This procedure involves the rapid formation of surfactant softly coated Co nanostructures followed by a slow separation process of the magnetic-field responsive Co/surfactant nanocomposites from the liquid phase. The detailed structure of thin films of the Co/surfactant nanocomposites has been investigated by scanning force microscopy (SFM). The thin films were characterized by different anisotropic features. Micrometric long domains of self-aligned ellipsoidal NPs (tens of nanometers in size) have been observed, together with bendable micrometric long homogeneous nanofibers (NFs). The film structures were strongly dependent on the Co/surfactant ratio and, by increasing the Co percentage, the system was forced towards the formation of mutually connected superstructures consisting of anisotropic bands of self-aligned NFs and anisotropic 2D close packed Co-NP super-lattices. Transmission electron microscopy (TEM) showed that the NPs observed by SFM are in effect composed of almost spherical and oxygen-free cobalt nanoparticles, 1-3 nm in size, which typically assemble in larger ellipsoidal systems tens of nanometers in size. Magnetic force microscopy (MFM) demonstrates the magnetic response of these thin films, highlighting the different behavior (attractive/repulsive) of the Co-NPs aggregates towards the oscillating magnetized tip. The above structural findings have been interpreted in terms of nanostructures/matrix interaction along with a fine balance between short-range isotropic repulsions, van der Waals attractions and long-range anisotropic magnetic interactions.

  5. Sodium cleaning from sodium contaminated components and operation for experimental equipment

    Energy Technology Data Exchange (ETDEWEB)

    Kim, B. H.; Kim, J. M.; Kim, T. J.; Nam, H. Y.; Jeong, J. Y.; Choi, B. H.; Choi, J. H

    2007-11-15

    An objective of washing technology development for sodium contaminated equipment is to clean and reuse safely and effectively the used equipment through a washing and maintenance, and recovery of the sodium wastes generated during washing.

  6. Electrolytic process to produce sodium hypochlorite using sodium ion conductive ceramic membranes

    Energy Technology Data Exchange (ETDEWEB)

    Balagopal, Shekar; Malhotra, Vinod; Pendleton, Justin; Reid, Kathy Jo

    2012-09-18

    An electrochemical process for the production of sodium hypochlorite is disclosed. The process may potentially be used to produce sodium hypochlorite from seawater or low purity un-softened or NaCl-based salt solutions. The process utilizes a sodium ion conductive ceramic membrane, such as membranes based on NASICON-type materials, in an electrolytic cell. In the process, water is reduced at a cathode to form hydroxyl ions and hydrogen gas. Chloride ions from a sodium chloride solution are oxidized in the anolyte compartment to produce chlorine gas which reacts with water to produce hypochlorous and hydrochloric acid. Sodium ions are transported from the anolyte compartment to the catholyte compartment across the sodium ion conductive ceramic membrane. Sodium hydroxide is transported from the catholyte compartment to the anolyte compartment to produce sodium hypochlorite within the anolyte compartment.

  7. Mechanical properties of cement mortar in sodium sulfate and sodium chloride solutions

    Institute of Scientific and Technical Information of China (English)

    熊良宵; 虞利军

    2015-01-01

    To investigate the mechanical properties of cement mortar in sodium sulfate and sodium chloride solutions, uniaxial compression test and ultrasonic test were performed. Test results show that the relative dynamic elastic modulus, the mass variation, and the compressive strength of cement mortar increase first, and then decrease with increasing erosion time in sodium sulfate and sodium chloride solutions. The relative dynamic elastic moduli and the compressive strengths of cement mortars with water/cement ratios of 0.55 and 0.65 in sodium sulfate solution are lower than those in sodium chloride solution with the same concentration at the 420th day of immersion. The compressive strength of cement mortar with water/cement ratio of 0.65 is more sensitive to strain rate than that with water/cement ratio of 0.55. In addition, the strain-rate sensitivity of compressive strength of cement mortar will increase under attacks of sodium sulfate or sodium chloride solution.

  8. Development of dismantling and sodium removal technique for large sodium components

    Energy Technology Data Exchange (ETDEWEB)

    Hirakawa, Yasushi; Nakai, Satoru [Japan Nuclear Cycle Development Inst., Oarai, Ibaraki (Japan). Oarai Engineering Center

    2002-06-01

    Large sodium test facilities that had been constructed to perform R and D for Monju were dismantled after the removal of sodium. Because experience of such tasks in limited, for the establishment of the technology, information on past experiences, R and D results, the results of small-scale sodium removal experiments and related information were gathered worldwide. Different sodium removal processes such as the alcohol process, water vapor nitrogen process, aestivation process etc. were selected based on the component structure and were applied to various components such as the steam generator, cold trap, intermediate heat exchanger etc. As a result, sodium removal and dismantling of these facilities were conducted successfully without sodium fires, injuries caused by sodium and with little burden to the environment. Furthermore, problems to be solved when applying these processes to the radioactive sodium components were identified and an R and D plan was drawn up. (author)

  9. EVALUATION OF THE URINARY SODIUM EXCRETION IN PATIENTS WITH LOW SODIUM DIET

    Directory of Open Access Journals (Sweden)

    Andrea Emanuela

    2012-06-01

    We conclude that sodium intake in this population at risk is excessive. There was good correlation between the intake of sodium and excretion. Future studies should examine the impact of nutritional interventions aimed at reducing sodium intake in this group of patients.

  10. 77 FR 71006 - Sodium Nitrite Injection and Sodium Thiosulfate Injection Drug Products Labeled for the Treatment...

    Science.gov (United States)

    2012-11-28

    ... HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2012-N-1134 Sodium Nitrite Injection and Sodium Thiosulfate Injection Drug Products Labeled for the Treatment of Cyanide Poisoning; Enforcement... products containing sodium nitrite labeled for the treatment of cyanide poisoning and unapproved...

  11. Inhaled sodium cromoglycate for asthma in children

    NARCIS (Netherlands)

    van der Wouden, Johannes C.; Uijen, Johannes H. J. M.; Bernsen, Roos M. D.; Tasche, Marjolein J. A.; de Jongste, Johan C.; Ducharme, Francine

    2008-01-01

    Background Sodium cromoglycate has been recommended as maintenance treatment for childhood asthma for many years. Its use has decreased since 1990, when inhaled corticosteroids became popular, but it is still used in many countries. Objectives To determine the efficacy of sodium cromoglycate compare

  12. 21 CFR 582.7724 - Sodium alginate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium alginate. 582.7724 Section 582.7724 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... alginate. (a) Product. Sodium alginate. (b) Conditions of use. This substance is generally recognized...

  13. 21 CFR 573.700 - Sodium nitrite.

    Science.gov (United States)

    2010-04-01

    ... Listing § 573.700 Sodium nitrite. Sodium nitrite may be safely used in canned pet food containing meat and fish in accordance with the following prescribed conditions: (a) It is used or intended for use alone as a preservative and color fixative in canned pet food containing fish, meat, and fish and...

  14. 21 CFR 182.8778 - Sodium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium phosphate. 182.8778 Section 182.8778 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... phosphate. (a) Product. Sodium phosphate (mono-, di-, and tribasic). (b) Conditions of use. This...

  15. 21 CFR 182.6778 - Sodium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium phosphate. 182.6778 Section 182.6778 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... phosphate. (a) Product. Sodium phosphate (mono-, di-, and tribasic). (b) Conditions of use. This...

  16. Assessment of sodium conductor distribution cable

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-06-01

    The study assesses the barriers and incentives for using sodium conductor distribution cable. The assessment considers environmental, safety, energy conservation, electrical performance and economic factors. Along with all of these factors considered in the assessment, the sodium distribution cable system is compared to the present day alternative - an aluminum conductor system. (TFD)

  17. The Sodium Tail of the Moon

    Science.gov (United States)

    Matta, M.; Smith, S.; Baumgardner, J.; Wilson, J.; Martinis, C.; Mendillo, M.

    2009-01-01

    During the few days centered about new Moon, the lunar surface is optically hidden from Earth-based observers. However, the Moon still offers an observable: an extended sodium tail. The lunar sodium tail is the escaping "hot" component of a coma-like exosphere of sodium generated by photon-stimulated desorption, solar wind sputtering and meteoroid impact. Neutral sodium atoms escaping lunar gravity experience solar radiation pressure that drives them into the anti-solar direction forming a comet-like tail. During new Moon time, the geometry of the Sun, Moon and Earth is such that the anti-sunward sodium flux is perturbed by the terrestrial gravitational field resulting in its focusing into a dense core that extends beyond the Earth. An all-sky camera situated at the El Leoncito Observatory (CASLEO) in Argentina has been successfully imaging this tail through a sodium filter at each lunation since April 2006. This paper reports on the results of the brightness of the lunar sodium tail spanning 31 lunations between April 2006 and September 2008. Brightness variability trends are compared with both sporadic and shower meteor activity, solar wind proton energy flux and solar near ultra violet (NUV) patterns for possible correlations. Results suggest minimal variability in the brightness of the observed lunar sodium tail, generally uncorrelated with any single source, yet consistent with a multi-year period of minimal solar activity and non-intense meteoric fluxes.

  18. Sodium Heat Engine Development Program

    Energy Technology Data Exchange (ETDEWEB)

    Singh, J.P.; Kupperman, D.S.; Majumdar, S.; Dorris, S.; Gopalsami, N.; Dieckman, S.L.; Jaross, R.A.; Johnson, D.L.; Gregar, J.S.; Poeppel, R.B.; Raptis, A.C.; Valentin, R.A.

    1992-01-01

    The Sodium Heat Engine (SHE) is an efficient thermoelectric conversion device which directly generates electricity from a thermally regenerative electrochemical cell that relies on the unique conduction properties of {beta}{double prime}-alumina solid electrolyte (BASE). Laboratory models of a variety of SHE devices have demonstrated the feasibility and efficiency of the system, engineering development of large prototype devices has been slowed by a series of materials and fabrication problems. Failure of the electrolyte tubes has been a recurring problem and a number of possible causes have been postulated. To address these issues, a two-phase engineering development program was undertaken. This report summarizes the final results of the first phase of the program, which included extensive materials characterization activities, a study of applicable nondestructive evaluation methods, an investigation of possible stress states that would contribute to fracture, and certain operational issues associated with the electromagnetic pumps used in the SHE prototype. Mechanical and microstructural evaluation of commercially obtained BASE tubes revealed that they should be adequate for SHE applications and that sodium exposure produced no appreciable deleterious strength effects. Processing activities to produce a more uniform and smaller grain size for the BASE tubes were completed using isostatic pressing, extrusion, and slip casting. Green tubes were sintered by conventional and microwave plasma methods. Of particular interest is the residual stress state in the BASE tubes, and both analysis and nondestructive evaluation methods were employed to evaluate these stresses. X-ray and neutron diffraction experiments were performed to determine the bulk residual stresses in commercially fabricated BASE tubes; however, tube-to-tube variations and variations among the various methods employed did not allow formulation of a definitive definition of the as-fabricated stress state.

  19. Sodium hypochlorite-induced acute kidney injury.

    Science.gov (United States)

    Peck, Brandon W; Workeneh, Biruh; Kadikoy, Huseyin; Abdellatif, Abdul

    2014-03-01

    Sodium hypochlorite (bleach) is commonly used as an irrigant during dental procedures as well as a topical antiseptic agent. Although it is generally safe when applied topically, reports of accidental injection of sodium hypochlorite into tissue have been reported. Local necrosis, pain and nerve damage have been described as a result of exposure, but sodium hypo-chlorite has never been implicated as a cause of an acute kidney injury (AKI). In this report, we describe the first case of accidental sodium hypochlorite injection into the infraorbital tissue during a dental procedure that precipitated the AKI. We speculate that oxidative species induced by sodium hypochlorite caused AKI secondary to the renal tubular injury, causing mild acute tubular necrosis.

  20. Sodium hypochlorite-induced acute kidney injury

    Directory of Open Access Journals (Sweden)

    Brandon W Peck

    2014-01-01

    Full Text Available Sodium hypochlorite (bleach is commonly used as an irrigant during dental proce-dures as well as a topical antiseptic agent. Although it is generally safe when applied topically, reports of accidental injection of sodium hypochlorite into tissue have been reported. Local necrosis, pain and nerve damage have been described as a result of exposure, but sodium hypo-chlorite has never been implicated as a cause of an acute kidney injury (AKI. In this report, we describe the first case of accidental sodium hypochlorite injection into the infraorbital tissue during a dental procedure that precipitated the AKI. We speculate that oxidative species induced by sodium hypochlorite caused AKI secondary to the renal tubular injury, causing mild acute tubular necrosis.

  1. The role of sodium in the body

    Directory of Open Access Journals (Sweden)

    Munteanu Constantin

    2011-05-01

    Full Text Available Sodium is a metallic element with the symbol Na , in the same group with Li, K, Rb, Cs; is widespread in nature in the form of salts (nitrates, carbonates, chlorides, atomic number 11 and atomic weight 22,9898 . It,s a soft metal, reactive and with a low melting point , with a relative density of 0,97 at 200C (680 F. From the commercial point of view, sodium is the most important of all the alkaline metals. Elemental sodium was first isolated by Humpry Davy in 1807 by passing an electric current through molten sodium hydroxide. Elemental sodium does not occur naturally on earth, because it quickly oxidizes in air and is violently reactive with water, so it must be stored in a non-oxidizing medium, such as liquid hydrocarbon . The free metal is used for some chemical synthesis, analysis, and heat transfer applications .

  2. Effect of sodium ascorbate and sodium nitrite on protein and lipid oxidation in dry fermented sausages.

    Science.gov (United States)

    Berardo, A; De Maere, H; Stavropoulou, D A; Rysman, T; Leroy, F; De Smet, S

    2016-11-01

    The effects of sodium nitrite and ascorbate on lipid and protein oxidation were studied during the ripening process of dry fermented sausages. Samples were taken at day 0, 2, 8, 14, 21 and 28 of ripening to assess lipid (malondialdehyde) and protein (carbonyls and sulfhydryl groups) oxidation. Sodium ascorbate and nitrite were separately able to reduce the formation of malondialdehyde. Their combined addition resulted in higher amounts of carbonyl compounds compared to their separate addition or the treatment without any of both compounds. Moreover, sodium nitrite limited the formation of γ-glutamic semialdehyde whereas sodium ascorbate showed a pro-oxidant effect. A loss of thiol groups was observed during ripening, which was not affected by the use of sodium ascorbate nor sodium nitrite. In conclusion, sodium nitrite and ascorbate affected protein and lipid oxidation in different manners. The possible pro-oxidant effect of their combined addition on carbonyl formation might influence the technological and sensory properties of these products.

  3. Sodium-NaK engineering handbook. Volume III. Sodium systems, safety, handling, and instrumentation. [LMFBR

    Energy Technology Data Exchange (ETDEWEB)

    Foust, O J [ed.

    1978-01-01

    The handbook is intended for use by present and future designers in the Liquid Metals Fast Breeder Reactor (LMFBR) Program and by the engineering and scientific community performing other type investigation and exprimentation requiring high-temperature sodium and NaK technology. The arrangement of subject matter progresses from a technological discussion of sodium and sodium--potassium alloy (NaK) to discussions of varius categories and uses of hardware in sodium and NaK systems. Emphasis is placed on sodium and NaK as heat-transport media. Sufficient detail is included for basic understanding of sodium and NaK technology and of technical aspects of sodium and NaK components and instrument systems. Information presented is considered adequate for use in feasibility studies and conceptual design, sizing components and systems, developing preliminary component and system descriptions, identifying technological limitations and problem areas, and defining basic constraints and parameters.

  4. Sodium D-line emission in Comet West (1975n) and the sodium source in Comets

    Energy Technology Data Exchange (ETDEWEB)

    Oppenheimer, M.

    1980-09-15

    A spectrum of the sodium D-line emission from Comet West (1975n) taken at heliocentric distance 1.4 AU is analyzed by comparing the D-line brightness to that in the underlying continuum. Using the observations of this comet by Ney and Merrill, we find that the dust grains which dominate the visible and infrared continua are too cool to to provide the observed sodium atoms through evaporation of sodium metal or a sodium compound from grain surfaces. Though sodium metal may evaporate from a small-grain component, we suggest that molecules embedded in the volatile nuclear matrix are a more plausible source of sodium. The relationship between this source and the interstellar sodium abundance is discussed.

  5. Nutritional impact of sodium reduction strategies on sodium intake from processed foods

    Science.gov (United States)

    Hendriksen, M A H; Verkaik-Kloosterman, J; Noort, M W; van Raaij, J M A

    2015-01-01

    Background/objectives: Sodium intake in the Netherlands is substantially above the recommended intake of 2400 mg/day. This study aimed to estimate the effect of two sodium reduction strategies, that is, modification of the composition of industrially processed foods toward the technologically feasible minimum level or alteration of consumers' behavior on sodium intake in the Netherlands. Subjects/methods: Data from the Dutch National Food Consumption Survey (2007–2010) and the Food Composition Table (2011) were used to estimate the current sodium intake. In the first scenario, levels in processed foods were reduced toward their technologically feasible minimum level (sodium reduction in processed foods scenario). The minimum feasible levels were based on literature searches or expert judgment. In the second scenario, foods consumed were divided into similar food (sub)groups. Subsequently, foods were replaced by low-sodium alternatives (substitution of processed foods scenario). Sodium intake from foods was calculated based on the mean of two observation days for the current food consumption pattern and the scenarios. Results: Sodium levels of processed foods could be reduced in most food groups by 50%, and this may reduce median sodium intake from foods by 38% (from 3042 to 1886 mg/day in adult men). Substitution of foods may reduce sodium intake by 47% (from 3042 to 1627 mg/day in adult men), owing to many low-sodium alternatives within food groups. Conclusions: In the Netherlands, reduction of sodium intake by modification of food composition or by alteration of behavior may substantially reduce the median sodium intake from foods below the recommended sodium intake. PMID:25782426

  6. Hydrogen embrittlement of type 410 stainless steel in sodium chloride, sodium sulfate, and sodium hydroxide environments at 90 C

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez-Rodriguez, J.G.; Salinas-Bravo, V.M. [Inst. de Investigaciones Electricas, Cuernavaca (Mexico). Dept. Fisico Quimica Aplicada; Martinez-Villafane, A. [Centro de Investigaciones en Materiales Avanzados Leon Tolstoi, Chihuahua (Mexico)

    1997-06-01

    Susceptibility of martensitic type 410 (UNS S41000) stainless steel (SS) to environmental cracking was evaluated at 90 C in concentrated sodium chloride, sodium sulfate and sodium hydroxide solutions, all of which are environments related to steam turbine conditions, using the slow strain rate testing (SSRT) technique. In NaCl, the effects of solution pH, concentration, and anodic and cathodic polarization were investigated. Tests were supplemented by detailed electron fractography and hydrogen permeation measurements. A clear correlation was found between the degree of embrittlement and the amount of hydrogen permeating the steel, suggesting a hydrogen-induced cracking mechanism.

  7. Sodium-metal halide and sodium-air batteries.

    Science.gov (United States)

    Ha, Seongmin; Kim, Jae-Kwang; Choi, Aram; Kim, Youngsik; Lee, Kyu Tae

    2014-07-21

    Impressive developments have been made in the past a few years toward the establishment of Na-ion batteries as next-generation energy-storage devices and replacements for Li-ion batteries. Na-based cells have attracted increasing attention owing to low production costs due to abundant sodium resources. However, applications of Na-ion batteries are limited to large-scale energy-storage systems because of their lower energy density compared to Li-ion batteries and their potential safety problems. Recently, Na-metal cells such as Na-metal halide and Na-air batteries have been considered to be promising for use in electric vehicles owing to good safety and high energy density, although less attention is focused on Na-metal cells than on Na-ion cells. This Minireview provides an overview of the fundamentals and recent progress in the fields of Na-metal halide and Na-air batteries, with the aim of providing a better understanding of new electrochemical systems. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Design and Commissioning Test of WKN Sodium Thermodynamic Test Loop

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    In the research of fast reactor a sodium thermodynamic test loop was designed and commissioned. Its highest operating temperature is 700℃, after the sodium is passed the cooler, the temperature of the sodium can be reduced to 300 ℃; the sodium flow is 0.2 m3/h. The loop consists of sodium electromagnetic pump, sodium flow meter, two groups of heater, two groups of cooler, surge tank, sodium vapor trap, diffusion cold trap, sodium transportation tank, electric control panel and microprocessor. It has two experimental bypass loops for research of heat transfer

  9. Scientific Opinion on the safety evaluation of the active substances, sodium carbonate peroxyhydrate coated with sodium carbonate and sodium silicate, bentonite, sodium chloride, sodium carbonate for use in active food contact materials

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids (CEF

    2013-04-01

    Full Text Available This scientific opinion of the Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids deals with the safety evaluation of the powder mixture of the active substances sodium carbonate peroxyhydrate coated with sodium carbonate and sodium silicate (FCM substance No 1009, bentonite (CAS No 1302-78-9, FCM No 393, sodium chloride (CAS No 7647-14-5, FCM No 985, sodium carbonate (CAS No 497-19-8, FCM No 1008 which are intended to be used as combined oxygen generator and carbon dioxide absorber in packaging containing whole fresh fruits. The powder mixture is placed in a nonwoven polyethylene sachet separated from the food by a pad. In the presence of moisture, sodium carbonate peroxyhydrate first decomposes into sodium carbonate and hydrogen peroxide which decomposes into water and oxygen. Sodium carbonate reacts with carbon dioxide to form sodium bicarbonate. Because the sachet is not placed in direct contact with the food or food exudates, only hydrogen peroxide which decomposes to water and oxygen may be released with no other potential migration of volatile compounds. Based on the conclusion drawn in the EU Risk Assessment Report that hydrogen peroxide is not classified as a mutagen and the results from a subchronic toxicity study with hydrogen peroxide, the Panel concluded that hydrogen peroxide does not raise a safety concern under the intended conditions of use. Therefore the CEF Panel concluded that sodium carbonate peroxyhydrate coated with sodium carbonate and sodium silicate, bentonite, sodium chloride and sodium carbonate do not raise a safety concern for the consumer when used as combined oxygen generator and carbon dioxide absorber, for packaging of whole fruits. The substances should be used in sachets which prevent the release of the powder mixture into the food. Sachets should not be in direct contact with food or food exudates.

  10. A Global Model of Meteoric Sodium

    Science.gov (United States)

    Marsh, Daniel R.; Janches, Diego; Feng, Wuhu; Plane, John M. C.

    2013-01-01

    A global model of sodium in the mesosphere and lower thermosphere has been developed within the framework of the National Center for Atmospheric Research's Whole Atmosphere Community Climate Model (WACCM). The standard fully interactive WACCM chemistry module has been augmented with a chemistry scheme that includes nine neutral and ionized sodium species. Meteoric ablation provides the source of sodium in the model and is represented as a combination of a meteoroid input function (MIF) and a parameterized ablation model. The MIF provides the seasonally and latitudinally varying meteoric flux which is modeled taking into consideration the astronomical origins of sporadic meteors and considers variations in particle entry angle, velocity, mass, and the differential ablation of the chemical constituents. WACCM simulations show large variations in the sodium constituents over time scales from days to months. Seasonality of sodium constituents is strongly affected by variations in the MIF and transport via the mean meridional wind. In particular, the summer to winter hemisphere flow leads to the highest sodium species concentrations and loss rates occurring over the winter pole. In the Northern Hemisphere, this winter maximum can be dramatically affected by stratospheric sudden warmings. Simulations of the January 2009 major warming event show that it caused a short-term decrease in the sodium column over the polar cap that was followed by a factor of 3 increase in the following weeks. Overall, the modeled distribution of atomic sodium in WACCM agrees well with both ground-based and satellite observations. Given the strong sensitivity of the sodium layer to dynamical motions, reproducing its variability provides a stringent test of global models and should help to constrain key atmospheric variables in this poorly sampled region of the atmosphere.

  11. Pharmacologic inhibition of intestinal sodium uptake: a gut centric approach to sodium management.

    Science.gov (United States)

    Spencer, Andrew G; Greasley, Peter J

    2015-09-01

    Impaired sodium excretion in patients with chronic kidney disease (CKD) can drive fluid overload and hypertension and accelerate CKD progression. Diuretics reduce fluid overload but require residual kidney function to work. Adherence to dietary sodium restriction is generally poor. Here, we review an alternative pharmacologic strategy aimed at reducing sodium absorption from the gut. Genetic studies implicate the sodium/hydrogen exchanger isoform 3 (NHE3) as the major absorptive sodium transporter. Pharmacologic inhibition of apically expressed gut NHE3 offers the potential of reducing sodium absorption and fluid overload independent of kidney function and with better safety than systemic drugs. Two small-molecule inhibitors of NHE3 (tenapanor and SAR218034) with minimal systemic exposure reduce urinary sodium and increase stool sodium in a dose-dependent manner in rodents, with similar results observed with tenapanor in humans. These molecules also reduce blood pressure in rat models of CKD (tenapanor) and hypertension (SAR218034). Clinical trials of tenapanor in patients with CKD-related disorders are ongoing. Pharmacologic inhibition of gut NHE3 may be a viable strategy for managing sodium load in patients with CKD or with sodium-sensitive hypertension in general. Ongoing clinical trials will shed further light on the potential benefits of this approach.

  12. Radioimmunoassay of sodium cromoglycate in human plasma

    Energy Technology Data Exchange (ETDEWEB)

    Brown, K.; Gardner, J.J.; Lockley, W.J.S.; Preston, J.R.; Wilkinson, D.J. (Fisons plc, Loughborough (UK). Pharmaceutical Div.)

    1983-01-01

    A sensitive radioimmunoassay method for sodium cromoglycate in human plasma is described. The lowest quantifiable concentration of sodium cromoglycate is 0.93 nmol/l when 0.1 ml plasma samples are analysed. The range of the method is limited; both 0.01 and 0.1 ml volumes of plasma must be analysed to encompass the concentration range 0.93-139 nmol/l which may be encountered in plasma samples from patients and human volunteers. The method is specific for sodium cromoglycate as indicated by a low cross-reactivity of the anti-cromoglycate antiserum with a number of drugs.

  13. Interaction of theobromine with sodium benzoate

    Energy Technology Data Exchange (ETDEWEB)

    Nishijo, J.; Yonetani, I.

    1982-03-01

    The interaction of theobromine with sodium benzoate was investigated by PMR spectroscopy. The interaction of theobromine with pentadeuterated benzoic acid (benzoic acid-d5) was examined in the same manner but to a lesser degree. Chemical shifts of theobromine protons were determined as a function of sodium benzoate concentration in deuterium oxide at 30 and 15 degrees. Signals of both methyl groups of theobromine underwent significant upfield shifts when sodium benzoate was added to a theobromine solution. This fact suggests that a complex is formed by vertical stacking or plane-to-plane stacking. The same results were obtained for benzoic acid-d5.

  14. Formaldehyde impairs transepithelial sodium transport

    Science.gov (United States)

    Cui, Yong; Li, Huiming; Wu, Sihui; Zhao, Runzhen; Du, Deyi; Ding, Yan; Nie, Hongguang; Ji, Hong-Long

    2016-01-01

    Unsaturated oxidative formaldehyde is a noxious aldehyde in cigarette smoke that causes edematous acute lung injury. However, the mechanistic effects of formaldehyde on lung fluid transport are still poorly understood. We examined how formaldehyde regulates human epithelial sodium channels (ENaC) in H441 and expressed in Xenopus oocytes and exposed mice in vivo. Our results showed that formaldehyde reduced mouse transalveolar fluid clearance in vivo. Formaldehyde caused a dose-dependent inhibition of amiloride-sensitive short-circuit Na+ currents in H441 monolayers and of αβγ-ENaC channel activity in oocytes. α-ENaC protein was reduced, whereas phosphorylation of the extracellular regulated protein kinases 1 and 2 (ERK1/2) increased significantly post exposure. Moreover, both α- and γ-ENaC transcripts were down-regulated. Reactive oxygen species (ROS) was elevated significantly by formaldehyde in addition to markedly augmented membrane permeability of oocytes. These data suggest that formaldehyde contributes to edematous acute lung injury by reducing transalveolar Na+ transport, through decreased ENaC activity and enhanced membrane depolarization, and by elevating ROS production over long-term exposure. PMID:27762337

  15. Heterogeneous Transmutation Sodium Fast Reactor

    Energy Technology Data Exchange (ETDEWEB)

    S. E. Bays

    2007-09-01

    The threshold-fission (fertile) nature of Am-241 is used to destroy this minor actinide by capitalizing upon neutron capture instead of fission within a sodium fast reactor. This neutron-capture and its subsequent decay chain leads to the breeding of even neutron number plutonium isotopes. A slightly moderated target design is proposed for breeding plutonium in an axial blanket located above the active “fast reactor” driver fuel region. A parametric study on the core height and fuel pin diameter-to-pitch ratio is used to explore the reactor and fuel cycle aspects of this design. This study resulted in both non-flattened and flattened core geometries. Both of these designs demonstrated a high capacity for removing americium from the fuel cycle. A reactivity coefficient analysis revealed that this heterogeneous design will have comparable safety aspects to a homogeneous reactor of comparable size. A mass balance analysis revealed that the heterogeneous design may reduce the number of fast reactors needed to close the current once-through light water reactor fuel cycle.

  16. Estimating 24-hour urinary sodium excretion from casual urinary sodium concentrations in Western populations

    DEFF Research Database (Denmark)

    Brown, Ian J; Dyer, Alan R; Chan, Queenie

    2013-01-01

    High intakes of dietary sodium are associated with elevated blood pressure levels and an increased risk of cardiovascular disease. National and international guidelines recommend reduced sodium intake in the general population, which necessitates population-wide surveillance. We assessed...... the utility of casual (spot) urine specimens in estimating 24-hour urinary sodium excretion as a marker of sodium intake in the International Cooperative Study on Salt, Other Factors, and Blood Pressure. There were 5,693 participants recruited in 1984-1987 at the ages of 20-59 years from 29 North American...... and European samples. Participants were randomly assigned to test or validation data sets. Equations derived from casual urinary sodium concentration and other variables in the test data were applied to the validation data set. Correlations between observed and estimated 24-hour sodium excretion were 0...

  17. Radioimmunoassay of sodium cromoglycate in human plasma

    Energy Technology Data Exchange (ETDEWEB)

    Brown, K.; Gardner, J.J.; Lockley, W.J.S.; Preston, J.R.; Wilkinson, D.J. (Fisons Ltd., Loughborough (UK). Pharmaceutical Div.)

    1983-01-01

    A sensitive radioimmunoassay method for sodium cromoglycate in human plasma is described. The lowest quantifiable concentration of sodium cromoglycate is 0.93 nmol/1 when 0.1 ml plasma samples are analysed. Direct analysis of sodium cromoglycate concentrations in plasma samples collected up to several hours after the administration of single therapeutic doses of the compound is possible. The range of the method is limited; both 0.01 and 0.1 ml volumes of plasma must be analysed to encompass the concentration range 0.93-139 nmol/1 which may be encountered in plasma samples from patients and human volunteers. The method is specific for sodium cromoglycate as indicated by a low cross-reactivity of the anti-cromoglycate antiserum with a number of drugs.

  18. Brain Sodium Channel and Febrile Seizure Mechanism

    Directory of Open Access Journals (Sweden)

    J Gordon Millichap

    2009-10-01

    Full Text Available Researchers at the University of Melbourne, Australia, measured the effect of temperature on brain sodium channel, Nav1.2, properties, using a computer model of the dentate gyrus granule cell.

  19. 21 CFR 184.1763 - Sodium hydroxide.

    Science.gov (United States)

    2010-04-01

    ... HUMAN CONSUMPTION (CONTINUED) DIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of.... 1310-73-2) is also known as sodium hydrate, soda lye, caustic soda, white caustic, and lye....

  20. Trifluoromethylation of Carbonyl Compounds with Sodium Trifluoroacetate

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    In the presence of copper (Ⅰ) halide as catalyst, a variety of carbonyl compounds could be trifluoromethylated with sodium trifluoroacetate to give the corresponding alcohols in moderate to high yields.

  1. Kinetics of wet sodium vapor complex plasma

    Science.gov (United States)

    Mishra, S. K.; Sodha, M. S.

    2014-04-01

    In this paper, we have investigated the kinetics of wet (partially condensed) Sodium vapor, which comprises of electrons, ions, neutral atoms, and Sodium droplets (i) in thermal equilibrium and (ii) when irradiated by light. The formulation includes the balance of charge over the droplets, number balance of the plasma constituents, and energy balance of the electrons. In order to evaluate the droplet charge, a phenomenon for de-charging of the droplets, viz., evaporation of positive Sodium ions from the surface has been considered in addition to electron emission and electron/ion accretion. The analysis has been utilized to evaluate the steady state parameters of such complex plasmas (i) in thermal equilibrium and (ii) when irradiated; the results have been graphically illustrated. As a significant outcome irradiated, Sodium droplets are seen to acquire large positive potential, with consequent enhancement in the electron density.

  2. Astrocyte Sodium Signalling and Panglial Spread of Sodium Signals in Brain White Matter.

    Science.gov (United States)

    Moshrefi-Ravasdjani, Behrouz; Hammel, Evelyn L; Kafitz, Karl W; Rose, Christine R

    2017-02-18

    In brain grey matter, excitatory synaptic transmission activates glutamate uptake into astrocytes, inducing sodium signals which propagate into neighboring astrocytes through gap junctions. These sodium signals have been suggested to serve an important role in neuro-metabolic coupling. So far, it is unknown if astrocytes in white matter-that is in brain regions devoid of synapses-are also able to undergo such intra- and intercellular sodium signalling. In the present study, we have addressed this question by performing quantitative sodium imaging in acute tissue slices of mouse corpus callosum. Focal application of glutamate induced sodium transients in SR101-positive astrocytes. These were largely unaltered in the presence of ionotropic glutamate receptors blockers, but strongly dampened upon pharmacological inhibition of glutamate uptake. Sodium signals induced in individual astrocytes readily spread into neighboring SR101-positive cells with peak amplitudes decaying monoexponentially with distance from the stimulated cell. In addition, spread of sodium was largely unaltered during pharmacological inhibition of purinergic and glutamate receptors, indicating gap junction-mediated, passive diffusion of sodium between astrocytes. Using cell-type-specific, transgenic reporter mice, we found that sodium signals also propagated, albeit less effectively, from astrocytes to neighboring oligodendrocytes and NG2 cells. Again, panglial spread was unaltered with purinergic and glutamate receptors blocked. Taken together, our results demonstrate that activation of sodium-dependent glutamate transporters induces sodium signals in white matter astrocytes, which spread within the astrocyte syncytium. In addition, we found a panglial passage of sodium signals from astrocytes to NG2 cells and oligodendrocytes, indicating functional coupling between these macroglial cells in white matter.

  3. Clinical evaluation of nedocromil sodium in asthma.

    Science.gov (United States)

    Holgate, S T

    1986-01-01

    The recognition that inflammatory events in the airways play a key role in the pathogenesis of asthma has led to a relentless search for pharmacological agents which modify these processes. Nedocromil sodium (Tilade) represents one such agent. Nedocromil sodium, when inhaled by patients with asthma (0.05-0.50% nebulized, 0.5-4.0 mg m.d.i.), has been shown to inhibit immediate bronchoconstriction provoked by challenges with allergen (10 studies), exercise (five studies), isocapnic hyperventilation, fog and sulphur dioxide (one study each) and adenosine (two studies). With these challenges, inhibition of bronchoconstriction exhibited dose-dependency up to 4 mg, with nedocromil sodium being up to four times more potent than sodium cromoglycate. When inhaled prior to allergen provocation, nedocromil sodium inhibited the late asthmatic reaction; when taken regularly during the pollen season, it attenuated the allergen-induced increase in non-specific bronchial responsiveness. The efficacy of nedocromil sodium (4 mg q.i.d.) in the treatment of clinical asthma was initially shown in four open studies and subsequently confirmed in nine double-blind, placebo-controlled 4-12 week studies on patients with seasonal and perennial asthma. Further clinical trials (eight studies) identified some difficulty in replacing inhaled corticosteroids with nedocromil sodium, especially if the corticosteroids were reduced rapidly (four studies). However, two studies have shown that nedocromil sodium produced further improvement in asthma symptoms when used in addition to bronchodilators and inhaled corticosteroids. Treatment with nedocromil sodium (4 mg q.i.d.) for up to 52 weeks demonstrated a progressive reduction in bronchodilator usage throughout the whole treatment period. During clinical assessment, nedocromil sodium was well tolerated, side-effects being unpleasant taste, nausea and headache. In most cases the adverse reactions were mild and transient, although in approximately 3% of

  4. Light scattering measurement of sodium polyacrylate products

    Science.gov (United States)

    Lama, Nisha; Norwood, David; Boone, Steven; Massie-Boyer, Valerie

    2015-03-01

    In the presentation, we will describe the use of a multi-detector HPLC incorporating the DAWN EOS multi-angle laser light scattering (MALLS) detector to measure the properties such as molecular weight, RMS radius, contour and persistence length and polydispersity of sodium polyacrylate products. The samples of sodium polyacrylate are used in various industries as thickening agents, coating dispersants, artificial snow, laundry detergent and disposable diapers. Data and results obtained from the experiment will be presented.

  5. Assessment of flow induced vibration in a sodium-sodium heat exchanger

    Energy Technology Data Exchange (ETDEWEB)

    Prakash, V. [Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India)], E-mail: prakash@igcar.gov.in; Thirumalai, M.; Prabhakar, R.; Vaidyanathan, G. [Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India)

    2009-01-15

    The 500 MWe Prototype Fast Breeder Reactor (PFBR) is under construction at Kalpakkam. It is a liquid metal sodium cooled pool type fast reactor with all primary components located inside a sodium pool. The heat produced due to fission in the core is transported by primary sodium to the secondary sodium in a sodium to sodium Intermediate Heat Exchanger (IHX), which in turn is transferred to water in the steam generator. PFBR IHX is a shell and tube type heat exchanger with primary sodium on shell side and secondary sodium in the tube side. Since IHX is one of the critical components placed inside the radioactive primary sodium, trouble-free operation of the IHX is very much essential for power plant availability. To validate the design and the adequacy of the support system provided for the IHX, flow induced vibration (FIV) experiments were carried out in a water test loop on a 60 deg. sector model. This paper discusses the flow induced vibration measurements carried out in 60 deg. sector model of IHX, the modeling criteria, the results and conclusion.

  6. Advanced sodium fast reactor accident source terms :

    Energy Technology Data Exchange (ETDEWEB)

    Powers, Dana Auburn; Clement, Bernard; Denning, Richard; Ohno, Shuji; Zeyen, Roland

    2010-09-01

    An expert opinion elicitation has been used to evaluate phenomena that could affect releases of radionuclides during accidents at sodium-cooled fast reactors. The intent was to identify research needed to develop a mechanistic model of radionuclide release for licensing and risk assessment purposes. Experts from the USA, France, the European Union, and Japan identified phenomena that could affect the release of radionuclides under hypothesized accident conditions. They qualitatively evaluated the importance of these phenomena and the need for additional experimental research. The experts identified seven phenomena that are of high importance and have a high need for additional experimental research: High temperature release of radionuclides from fuel during an energetic event Energetic interactions between molten reactor fuel and sodium coolant and associated transfer of radionuclides from the fuel to the coolant Entrainment of fuel and sodium bond material during the depressurization of a fuel rod with breached cladding Rates of radionuclide leaching from fuel by liquid sodium Surface enrichment of sodium pools by dissolved and suspended radionuclides Thermal decomposition of sodium iodide in the containment atmosphere Reactions of iodine species in the containment to form volatile organic iodides. Other issues of high importance were identified that might merit further research as development of the mechanistic model of radionuclide release progressed.

  7. 21 CFR 181.34 - Sodium nitrite and potassium nitrite.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium nitrite and potassium nitrite. 181.34...-Sanctioned Food Ingredients § 181.34 Sodium nitrite and potassium nitrite. Sodium nitrite and potassium... fixatives and preservative agents, with or without sodium or potassium nitrate, in the curing of red...

  8. 21 CFR 133.121 - Low sodium colby cheese.

    Science.gov (United States)

    2010-04-01

    ... common name or names of the ingredient or ingredients used as a salt substitute. (f) Low sodium colby... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Low sodium colby cheese. 133.121 Section 133.121... Cheese and Related Products § 133.121 Low sodium colby cheese. Low sodium colby cheese is the food...

  9. Thermochemical analysis of laterite ore alkali roasting: Comparison of sodium carbonate, sodium sulfate, and sodium hydroxide

    Science.gov (United States)

    Samadhi, Tjokorde Walmiki

    2017-01-01

    The abundance of global nickel reserve is in fact dominated by low grade laterite ores containing only approximately 1.0-1.8 %-Ni. Indonesia is a major limonite and saprolite ores source, particularly in the Sulawesi, northern Maluku, and Papua islands. Production of nickel from laterites typically requires a pre-concentration step which breaks down the mineral crystalline structure, thereby facilitating the subsequent extraction of the valuable metals. This work discusses the thermochemical analysis of the alkali roasting of an Indonesian saprolite ore using Na2CO3, Na2SO4, and NaOH. These alkali compounds are selected due to their relatively low cost. The Factsage thermochemical computation package is used to predict thermodynamically stable gaseous, solution, pure liquid, and pure solid phases present in the roasting process at temperatures from 100 to 1200°C at ambient pressure, in inert atmosphere. The formation of a liquid solution (or slag) phase is interpreted as a major indicator of mineral structure breakdown. The computed slag formation temperatures are 373.2, 1041.4, and 792.0°C when using Na2CO3, Na2SO4, and NaOH, respectively. The masses of volatilized alkali at 1200°C with a total feed mass of 100 gram are 0.49, 3.24, and 3.25 mg for Na2CO3, Na2SO4, and NaOH, respectively. It is therefore hypothesized that Na2CO3 is the most competitive sodium-based alkali for saprolite ore roasting.

  10. 76 FR 37129 - Determination That SODIUM FLUORIDE F 18 (Sodium Fluoride F-18) Injection, 10 to 200 Millicuries...

    Science.gov (United States)

    2011-06-24

    ... HUMAN SERVICES Food and Drug Administration Determination That SODIUM FLUORIDE F 18 (Sodium Fluoride F... Drug Administration (FDA) has determined that SODIUM FLUORIDE F 18 (sodium fluoride F-18) injection, 10... FLUORIDE F 18 injection, 10 to 200 mCi/mL, if all other legal and regulatory requirements are met. FOR...

  11. Sodium stimulates growth of Panicum coloratum through enhanced photosynthesis

    Energy Technology Data Exchange (ETDEWEB)

    Matoh, Toru; Murata, Shinji (Kyoto Univ. (Japan))

    1990-04-01

    A sodium-requiring C{sub 4} plant, Panicum coloratum Walt. cv Kabulabula, was grown with and without sodium. Rate of nitrogen uptake and photosynthesis were measured during the recovery from sodium deficiency. The beneficial effect of sodium on growth was apparent irrespective of nitrogen source, ammonium- or nitrate-nitrogen. The leaf photosynthetic rate ({sup 14}CO{sub 2} fixation) doubled by sodium within 1 hour of the application.

  12. Sodium Stimulates Growth of Panicum coloratum through Enhanced Photosynthesis.

    Science.gov (United States)

    Matoh, T; Murata, S

    1990-04-01

    A sodium-requiring C(4) plant, Panicum coloratum Walt. cv Kabulabula, was grown with and without sodium. Rate of nitrogen uptake and photosynthesis were measured during the recovery from sodium deficiency. The beneficial effect of sodium on growth was apparent irrespective of nitrogen source, ammonium- or nitrate-nitrogen. The leaf photosynthetic rate ((14)CO(2) fixation) doubled by sodium within 1 hour of the application.

  13. Analysis of the action of lidocaine on insect sodium channels

    OpenAIRE

    Song, Weizhong; Silver, Kristopher S.; Du, Yuzhe; Liu, Zhiqi; Dong, Ke

    2010-01-01

    A new class of sodium channel blocker insecticides (SCBIs), which include indoxacarb, its active metabolite, DCJW, and metaflumizone, preferably block inactivated states of both insect and mammalian sodium channels in a manner similar to that by which local anesthetic (LA) drugs block mammalian sodium channels. A recent study showed that two residues in the cockroach sodium channel, F1817 and Y1824, corresponding to two key LA-interacting residues identified in mammalian sodium channels are n...

  14. Sodium Purification Device for Production of Tantalum Powder

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    In the process of tantalum powder production it requires pure sodium to reduce potassium fluotantalate, thus the design of a sodium purification device is improved, later it is built and commissioned. The device includes sodium transportation tank, storage tank, filter, cold trap, final storage tank, metering tank, regulating valve, argon purification system, electric control panel and instrument. Industrial purity sodium is purified, the impurities in the sodium were reduced to very

  15. Salt craving: the psychobiology of pathogenic sodium intake.

    Science.gov (United States)

    Morris, Michael J; Na, Elisa S; Johnson, Alan Kim

    2008-08-06

    Ionic sodium, obtained from dietary sources usually in the form of sodium chloride (NaCl, common table salt) is essential to physiological function, and in humans salt is generally regarded as highly palatable. This marriage of pleasant taste and physiological utility might appear fortunate--an appealing taste helps to ensure that such a vital substance is ingested. However, the powerful mechanisms governing sodium retention and sodium balance are unfortunately best adapted for an environment in which few humans still exist. Our physiological and behavioral means for maintaining body sodium and fluid homeostasis evolved in hot climates where sources of dietary sodium were scarce. For many reasons, contemporary diets are high in salt and daily sodium intakes are excessive. High sodium consumption can have pathological consequences. Although there are a number of obstacles to limiting salt ingestion, high sodium intake, like smoking, is a modifiable behavioral risk factor for many cardiovascular diseases. This review discusses the psychobiological mechanisms that promote and maintain excessive dietary sodium intake. Of particular importance are experience-dependent processes including the sensitization of the neural systems underlying sodium appetite and the effects of sodium balance on hedonic state and mood. Accumulating evidence suggests that plasticity within the central nervous system as a result of experience with high salt intake, sodium depletion, or a chronic unresolved sodium appetite fosters enduring changes in sodium related appetitive and consummatory behaviors.

  16. Concordance of dietary sodium intake and concomitant phosphate load : Implications for sodium interventions

    NARCIS (Netherlands)

    Humalda, J K; Keyzer, C A; Binnenmars, S H; Kwakernaak, A J; Slagman, M C J; Laverman, G D; Bakker, S J L; de Borst, M H; Navis, G J

    2016-01-01

    BACKGROUND AND AIMS: Both a high dietary sodium and high phosphate load are associated with an increased cardiovascular risk in patients with chronic kidney disease (CKD), and possibly also in non-CKD populations. Sodium and phosphate are abundantly present in processed food. We hypothesized that (m

  17. Concordance of dietary sodium intake and concomitant phosphate load : Implications for sodium interventions

    NARCIS (Netherlands)

    Humalda, J. K.; Keyzer, C. A.; Binnenmars, S. H.; Kwakernaak, A. J.; Slagman, M. C. J.; Laverman, G. D.; Bakker, S. J. L.; de Borst, M. H.; Navis, G. J.

    2016-01-01

    Background and aims: Both a high dietary sodium and high phosphate load are associated with an increased cardiovascular risk in patients with chronic kidney disease (CKD), and possibly also in non-CKD populations. Sodium and phosphate are abundantly present in processed food. We hypothesized that (m

  18. Nutritional impact of sodium reduction strategies on sodium intake from processed foods

    NARCIS (Netherlands)

    Hendriksen, M.A.H.; Verkaik-Kloosterman, J.; Noort, M.W.; Raaij, J.M.A. van

    2015-01-01

    Background/objectives: Sodium intake in the Netherlands is substantially above the recommended intake of 2400 mg/day. This study aimed to estimate the effect of two sodium reduction strategies, that is, modification of the composition of industrially processed foods toward the technologically feasib

  19. Nutritional impact of sodium reduction strategies on sodium intake from processed foods

    NARCIS (Netherlands)

    Hendriksen, M.A.H.; Verkaik-Kloosterman, J.; Noort, M.W.J.; Raaij, van J.M.A.

    2015-01-01

    Background/objectives: Sodium intake in the Netherlands is substantially above the recommended intake of 2400¿mg/day. This study aimed to estimate the effect of two sodium reduction strategies, that is, modification of the composition of industrially processed foods toward the technologically feasib

  20. Concordance of dietary sodium intake and concomitant phosphate load : Implications for sodium interventions

    NARCIS (Netherlands)

    Humalda, J K; Keyzer, C A; Binnenmars, S H; Kwakernaak, A J; Slagman, M C J; Laverman, G D; Bakker, S J L; de Borst, M H; Navis, G J

    2016-01-01

    BACKGROUND AND AIMS: Both a high dietary sodium and high phosphate load are associated with an increased cardiovascular risk in patients with chronic kidney disease (CKD), and possibly also in non-CKD populations. Sodium and phosphate are abundantly present in processed food. We hypothesized that (m

  1. Concordance of dietary sodium intake and concomitant phosphate load : Implications for sodium interventions

    NARCIS (Netherlands)

    Humalda, J. K.; Keyzer, C. A.; Binnenmars, S. H.; Kwakernaak, A. J.; Slagman, M. C. J.; Laverman, G. D.; Bakker, S. J. L.; de Borst, M. H.; Navis, G. J.

    2016-01-01

    Background and aims: Both a high dietary sodium and high phosphate load are associated with an increased cardiovascular risk in patients with chronic kidney disease (CKD), and possibly also in non-CKD populations. Sodium and phosphate are abundantly present in processed food. We hypothesized that (m

  2. Bradykinin-induced bronchoconstriction: inhibition by nedocromil sodium and sodium cromoglycate.

    Science.gov (United States)

    Dixon, C M; Barnes, P J

    1989-01-01

    1. The effects of inhaled nedocromil sodium and sodium cromoglycate on bradykinin-induced bronchoconstriction have been studied in a double-blind, placebo controlled study, in eight mild asthmatic subjects. 2. The subjects attended on four occasions. Fifteen minutes after drug pre-treatment a bradykinin challenge was performed. Increasing concentrations were inhaled until a greater than 40% fall in expiratory flow at 30% of vital capacity from a partial flow volume manoeuvre (V p30) was demonstrated. 3. Inhaled bradykinin (0.06-8.0 mg ml-1) caused dose-related bronchoconstriction with the geometric mean cumulative dose causing a 40% fall in V p30 (PD40) of 0.035 (95% CI: 0.02-0.07) mumol, after placebo inhalation, which was similar to that measured before the trial (0.04: 0.02-0.09 mumol). 4. Both nedocromil sodium (4 mg) and sodium cromoglycate (10 mg) gave significant protection (P less than 0.05) against bradykinin-induced bronchoconstriction (PD40 0.37: 0.19-0.72 mumol after nedocromil sodium and 0.22: 0.11-0.49 after sodium cromoglycate). 5. Since bradykinin-induced bronchoconstriction is probably neurally mediated we conclude that both nedocromil sodium and sodium cromoglycate have an action on neural pathways which may be useful in the control of asthma symptoms. PMID:2547408

  3. Nutritional impact of sodium reduction strategies on sodium intake from processed foods

    NARCIS (Netherlands)

    Hendriksen, M.A.H.; Verkaik-Kloosterman, J.; Noort, M.W.J.; Raaij, van J.M.A.

    2015-01-01

    Background/objectives: Sodium intake in the Netherlands is substantially above the recommended intake of 2400¿mg/day. This study aimed to estimate the effect of two sodium reduction strategies, that is, modification of the composition of industrially processed foods toward the technologically

  4. Nutritional impact of sodium reduction strategies on sodium intake from processed foods

    NARCIS (Netherlands)

    Hendriksen, M.A.H.; Verkaik-Kloosterman, J.; Noort, M.W.; Raaij, J.M.A. van

    2015-01-01

    Background/objectives: Sodium intake in the Netherlands is substantially above the recommended intake of 2400 mg/day. This study aimed to estimate the effect of two sodium reduction strategies, that is, modification of the composition of industrially processed foods toward the technologically

  5. Concordance of dietary sodium intake and concomitant phosphate load : Implications for sodium interventions

    NARCIS (Netherlands)

    Humalda, J. K.; Keyzer, C. A.; Binnenmars, S. H.; Kwakernaak, A. J.; Slagman, M. C. J.; Laverman, G. D.; Bakker, S. J. L.; de Borst, M. H.; Navis, G. J.

    Background and aims: Both a high dietary sodium and high phosphate load are associated with an increased cardiovascular risk in patients with chronic kidney disease (CKD), and possibly also in non-CKD populations. Sodium and phosphate are abundantly present in processed food. We hypothesized that

  6. Interactions between Different Classes of Surfactants and Metmyoglobin%不同类型表面活性剂与高铁肌红蛋白相互作用

    Institute of Scientific and Technical Information of China (English)

    张莹莹; 曹洪玉; 唐乾; 郑学仿

    2011-01-01

    通过UV-Vis 吸收光谱、同步荧光光谱、圆二色(CD)光谱等方法对阴离子型表面活性剂--琥珀酸二辛酯磺酸钠(AOT)和十二烷基苯磺酸钠(SDBS)、阳离子型表面活性剂--十六烷基三甲基溴化铵(CTAB)和十二烷基三甲基溴化铵(DTAB)、两性离子型表面活性剂--3-[(3-胆固醇氨丙基)二甲基氨基]-1-丙磺酸(CHAPS)与马心高铁肌红蛋白(metMb)的不同作用机理进行了探讨.结果显示:阴、阳离子型表面活性剂可以与蛋白发生较强烈的作用,且相互作用与表面活性剂的浓度密切相关.AOT和SDBS浓度的升高使得metMb的Soret 带发生红移且出现两个新的Q带,伴随着配体金属电荷转移(LMCT)带的消失,蛋白从水合的六配位高自旋复合物(6-cHs)转化成六配位低自旋高铁血红素复合物(6-cLs),低浓度的AOT和SDBS对Tyr 和Trp 微环境均有影响,能使metMb的二级结构发生变化; 而CTAB和DTAB在低浓度时对metMb的血红素中心影响不大,但是对Trp和Tyr 的微环境影响很大,高浓度时主要通过静电吸引作用以聚合体形式直接作用于血红素中心,使Soret 带发生蓝移,metMb 形成五配位高自旋(5-cHs)复合物,血红素从疏水腔中释放出来,metMb 的α螺旋含量减少.DTAB由于自身结构的特点,与CTAB作用于蛋白的过程有些区别,形成了一个中间态,但最终也导致血红素的暴露.两性离子型表面活性剂在测定浓度范围内不与metMb 发生作用,原因是CHAPS整体呈电中性,其与metMb的阴离子性或者阳离子性位点作用的能力很弱,同时也说明metMb表面带相反电荷的位点相距较远.结果充分证明表面活性剂与蛋白相互作用的方式与表面活性剂的种类、结构及其浓度有关.%Complexes of horse metmyoglobin (metMb) with the anionic surfactants sodium bis(2-ethylhexyl) sulfosuccinate (AOT) and sodium dodecyl benzene sulfonate (SDBS), the cationic surfactants dodecyl trimethylammonium bromide

  7. Sodium intake in US ethnic subgroups and potential impact of a new sodium reduction technology: NHANES Dietary Modeling

    OpenAIRE

    Fulgoni, Victor L.; Agarwal, Sanjiv; Spence, Lisa; Samuel, Priscilla

    2014-01-01

    Background Because excessive dietary sodium intake is a major contributor to hypertension, a reduction in dietary sodium has been recommended for the US population. Using the National Health and Nutrition Examination Survey (NHANES) 2007–2010 data, we estimated current sodium intake in US population ethnic subgroups and modeled the potential impact of a new sodium reduction technology on sodium intake. Methods NHANES 2007–2010 data were analyzed using The National Cancer Institute method to e...

  8. Method and system for producing hydrogen using sodium ion separation membranes

    Science.gov (United States)

    Bingham, Dennis N; Klingler, Kerry M; Turner, Terry D; Wilding, Bruce M; Frost, Lyman

    2013-05-21

    A method of producing hydrogen from sodium hydroxide and water is disclosed. The method comprises separating sodium from a first aqueous sodium hydroxide stream in a sodium ion separator, feeding the sodium produced in the sodium ion separator to a sodium reactor, reacting the sodium in the sodium reactor with water, and producing a second aqueous sodium hydroxide stream and hydrogen. The method may also comprise reusing the second aqueous sodium hydroxide stream by combining the second aqueous sodium hydroxide stream with the first aqueous sodium hydroxide stream. A system of producing hydrogen is also disclosed.

  9. Sodium phosphate as an ergogenic aid.

    Science.gov (United States)

    Buck, Christopher L; Wallman, Karen E; Dawson, Brian; Guelfi, Kym J

    2013-06-01

    Legal nutritional ergogenic aids can offer athletes an additional avenue to enhance their performance beyond what they can achieve through training. Consequently, the investigation of new nutritional ergogenic aids is constantly being undertaken. One emerging nutritional supplement that has shown some positive benefits for sporting performance is sodium phosphate. For ergogenic purposes, sodium phosphate is supplemented orally in capsule form, at a dose of 3-5 g/day for a period of between 3 and 6 days. A number of exercise performance-enhancing alterations have been reported to occur with sodium phosphate supplementation, which include an increased aerobic capacity, increased peak power output, increased anaerobic threshold and improved myocardial and cardiovascular responses to exercise. A range of mechanisms have been posited to account for these ergogenic effects. These include enhancements in 2,3-Diphosphoglycerate (2,3-DPG) concentrations, myocardial efficiency, buffering capacity and adenosine triphosphate/phosphocreatine synthesis. Whilst there is evidence to support the ergogenic benefits of sodium phosphate, many studies researching this substance differ in terms of the administered dose and dosing protocol, the washout period employed and the fitness level of the participants recruited. Additionally, the effect of gender has received very little attention in the literature. Therefore, the purpose of this review is to critically examine the use of sodium phosphate as an ergogenic aid, with a focus on identifying relevant further research.

  10. Toxicity of aerosols of sodium reaction products.

    Science.gov (United States)

    Zwicker, G M; Allen, M D; Stevens, D L

    1979-01-01

    Sodium is used as the heat transfer medium in several new energy technologies such as liquid-metal fast-breeder reactors and solar-thermal collection systems. Because sodium burns in air and reacts violently with water, the potential exists for an airborne release of sodium combustion products and subsequent human exposure. To help evaluate the potential short-term hazard from an accidental sodium fire, male juvenile or adult Wistar rats were exposed to sodium aerosols for 2 hours to determine the dose at which 50 percent of the animals were affected (ED50) for each age group. The estimated ED50 of 510 microgram/l for adults was not significantly different from the estimated ED50 of 489 microgram/l for juveniles. The incidence of acute laryngitis, attributed to exposure, was three times higher for juvenile rats than for adults, and the degree of severity of this lesion was significantly (P less than 0.05) higher for juveniles.

  11. Idraparinux sodium: SANORG 34006, SR 34006.

    Science.gov (United States)

    2004-01-01

    Idraparinux sodium [SANORG 34006, SR 34006], a synthetic, anti Xa pentasaccharide and analogue of SR 32701 and fondaparinux sodium, was in development with Sanofi (now Sanofi-Synthélabo) and Organon (Akzo Nobel) in Europe and the USA (now Sanofi-Synthélabo alone). It may have potential in the treatment and secondary prevention of thrombosis, especially deep-vein thrombosis (DVT). Because of the long duration of action of idraparinux sodium, it may be suitable for once-weekly administration. In January 2004, Sanofi-Synthélabo announced it was to acquire, before the end of the first quarter 2004, all the rights of Organon relating to idraparinux sodium, subject to approval of the regulatory authorities. Sanofi-Synthélabo is to make payments to Organon based on future sales. Idraparinux sodium has completed phase IIb development with the PERSIST study and it is in phase III clinical trials. In June 2003, Organon announced the initiation of pivotal phase III studies as a once-weekly treatment of DVT and pulmonary embolism (PE), and for the prevention of stroke in patients with atrial fibrillation. The AMADEUS study will focus on patients with atrial fibrillation while the Van Gogh PE, Van Gogh DVT and the Van Gogh extension (EXT) will focus on patients with DVT or PE.

  12. Sodium ascorbyl phosphate in topical microemulsions.

    Science.gov (United States)

    Spiclin, Polona; Homar, Miha; Zupancic-Valant, Andreja; Gasperlin, Mirjana

    2003-04-30

    Sodium ascorbyl phosphate is a hydrophilic derivative of ascorbic acid, which has improved stability arising from its chemical structure. It is used in cosmetic and pharmaceutical preparations since it has many favorable effects in the skin, the most important being antioxidant action. In order to achieve this, it has to be converted into free ascorbic acid by enzymatic degradation in the skin. In the present work, o/w and w/o microemulsions composed of the same ingredients, were selected as carrier systems for topical delivery of sodium ascorbyl phosphate. We showed that sodium ascorbyl phosphate was stable in both types of microemulsion with no significant influence of its location in the carrier system. To obtain liquid microemulsions appropriate for topical application, their viscosity was increased by adding thickening agents. On the basis of rheological characterization, 4.00% (m/m) colloidal silica was chosen as a suitable thickening agent for w/o microemulsions and 0.50% (m/m) xanthan gum for the o/w type. The presence of thickening agent and the location of sodium ascorbyl phosphate in the microemulsion influenced the in vitro drug release profiles. When incorporated in the internal aqueous phase, sustained release profiles were observed. This study confirmed microemulsions as suitable carrier systems for topical application of sodium ascorbyl phosphate.

  13. Temporal sodium release related to gel microstructural properties-implications for sodium reduction.

    Science.gov (United States)

    Kuo, Wan-Yuan; Lee, Youngsoo

    2014-11-01

    The microstructure of food can be engineered to enhance sodium release during mastication, which may be used as a strategy to reduce sodium content in foods. This study aimed to relate sodium release to microstructural properties of solid lipoproteic colloid (SLC) foods. The SLC gels with 1.5% (w/w) NaCl were prepared by homogenization of whey protein isolate and anhydrous milk fat, followed by heat-induced gelation. The gels varied in protein content (8% or 16%), fat content (0%, 11%, 22%, or 33%), and homogenization pressures (14 or 55 MPa). The maximum rate of sodium release during the initial gel compression increased with increasing gel porosity and pore size. This was due to more releasable serum in the gels with larger pore volume and larger pores. The maximum concentration of sodium at the end of sodium release increased with reduced size of the fat particles in the gels. The smaller fat particles were dispersed more uniformly and interrupted the protein network more, and facilitated the gel breakdown. The above findings suggested that, during the breakdown of the SLC gels, the major mechanisms of sodium release are via serum release followed by sodium diffusion, which are governed by the gel porosity and the particle size of fat, respectively. This study demonstrated the dependence of temporal sodium release properties on the microstructural properties of an SLC food system. The findings from this study could lay the foundation for further investigation of the dependence of saltiness perception on SLC microstructure, which can provide insight for sodium reduction in SLC products. © 2014 Institute of Food Technologists®

  14. The Effect of Chronic Sodium Loading and Sodium Restriction on Plasma Prostaglandin A, E and F Concentrations in Normal Humans

    Science.gov (United States)

    Zusman, Randall M.; Spector, David; Caldwell, Burton V.; Speroff, Leon; Schneider, George; Mulrow, Patrick J.

    1973-01-01

    It has been suggested that prostaglandins may be involved in the control of sodium homeostasis. Prostaglandin A and prostaglandin E have been shown to increase renal blood flow and urinary sodium excretion and prostaglandin A has been shown to stimulate aldosterone release. The purpose of this study was to determine the effect of chronic sodium loading and sodium restriction on plasma prostaglandin A, E, and F concentrations. Seven normal human volunteers were placed on three sodium intake diets: (a) ad lib. sodium intake, (b) high sodium intake, and (c) low sodium intake. Plasma prostaglandin A, E, and F concentrations were measured by radioimmunoassay. Mean prostaglandin A levels on the ad lib. diet were 1.60 ng/ml. Prostaglandin A levels decreased 49% to 0.82 ng/ml on the high sodium intake and increased 34% to 2.14 ng/ml on the low sodium intake. Prostaglandin A levels increased 161% on the low sodium diet in comparison with levels on the high sodium diet. Plasma prostaglandin E and F concentrations did not change significantly during variation in sodium intake. These results show that dietary sodium content markedly effects plasma prostaglandin A levels and that prostaglandins may play a role in the physiologic mechanism of sodium homeostasis. PMID:4700484

  15. Sodium Intake Requirements for Preterm Neonates: Review and Recommendations.

    Science.gov (United States)

    Bischoff, Adrianne R; Tomlinson, Christopher; Belik, Jaques

    2016-12-01

    It is widely accepted that sodium is an essential nutritional electrolyte and its deficiency is associated with neurological sequelae and poor growth. The provision of an adequate sodium intake to preterm neonates is hampered by the technical difficulty in clinically assessing total body sodium content. As addressed in this review, there is a lack of consensus on the definition of hyponatremia early in life, but there is no evidence that it should deviate from the widely accepted normative data for adult subjects. A low urinary sodium content is accepted by many as reflecting total body sodium deficiency, yet spot urinary sodium measurements are of questionable clinical value. The hormonal regulation of sodium homeostasis is here reviewed and the mechanism accounting for sodium deficiency-induced growth impairment in preterm infants addressed. Lastly, we provide evidence-based gestational and postnatal age-dependent recommendations for the provision of adequate sodium intake to preterm neonates.

  16. An emerging antiarrhythmic target: late sodium current.

    Science.gov (United States)

    Banyasz, T; Szentandrássy, N; Magyar, J; Szabo, Z; Nánási, P P; Chen-Izu, Y; Izu, L T

    2015-01-01

    The cardiac late sodium current (INa,L) has been in the focus of research in the recent decade. The first reports on the sustained component of voltage activated sodium current date back to the seventies, but early studies interpreted this tiny current as a product of a few channels that fail to inactivate, having neither physiologic nor pathologic implications. Recently, the cardiac INa,L has emerged as a potentially major arrhythmogenic mechanism in various heart diseases, attracting the attention of clinicians and researchers. Research activity on INa,L has exponentially increased since Ranolazine, an FDA-approved antianginal drug was shown to successfully suppress cardiac arrhythmias by inhibiting INa,L. This review aims to summarize and discuss a series of papers focusing on the cardiac late sodium current and its regulation under physiological and pathological conditions. We will discuss critical evidences implicating INa,L as a potential target for treating myocardial dysfunction and cardiac arrhythmias.

  17. Is sodium chloride worth its salt?

    Science.gov (United States)

    McIntosh, Euan; Andrews, Peter J

    2013-06-11

    The choice of fluid for resuscitation of the brain-injured patient remains controversial, and the 'ideal' resuscitation fluid has yet to be identified. Large volumes of hypotonic solutions must be avoided because of the risk of cerebral swelling and intracranial hypertension. Traditionally, 0.9% sodium chloride has been used in patients at risk of intracranial hypertension, but there is increasing recognition that 0.9% saline is not without its problems. Roquilly and colleagues show a reduction in the development of hyperchloremic acidosis in brain-injured patients given 'balanced' solutions for maintenance and resuscitation compared with 0.9% sodium chloride. In this commentary, we explore the idea that we should move away from 0.9% sodium chloride in favor of a more 'physiological' solution.

  18. Electrochemical Oxygen Sensor Development for Liquid Sodium

    Science.gov (United States)

    Nollet, Billy K.

    Safe operation of a sodium-cooled fast reactor (SFR) requires in-depth understanding of the corrosion implications of liquid sodium coolant on reactor materials. Dissolved oxygen concentration is of particular importance in characterizing sodium attack, so an accurate means of measuring and controlling oxygen is crucial. There is significant room for improvement in current oxygen sensing technology, so extensive research has been conducted at the University of Wisconsin-Madison to address this issue. Experimental facilities and electrochemical oxygen sensors have been developed, tested, and analyzed. This research is discussed in detail in this report. The oxygen sensors tested in this research were developed using a yttria stabilized zirconia (YSZ) electrolyte whereas many of the past research in this field was conducted with yttria doped thoria (YDT or YST) electrolytes. Thorium, an alpha emitter, is expensive and increasingly difficult to acquire, so motivation to switch to a new material exists. YSZ is commonly used as the electrolyte for solid oxide fuel cells, and ample data is available for high temperature ionic conduction of this material. While some work has been done with YSZ in oxygen sensors (the automotive field, for example, uses YSZ O2 sensors), research on YSZ sensors in sodium is limited. A thorough study of YSZ-based electrochemical oxygen sensors must include detailed corrosion testing and analysis of YSZ in liquid sodium, careful oxygen sensor development and testing, and finally, a comprehensive analysis of the acquired sensor data. The research presented in this report describes the design and development of an electrochemical oxygen sensor for use in sodium using a YSZ electrolyte through the previously-mentioned steps. The designed sensors were subjected to a series of hypotheses which advance common understanding of oxygen sensor signal. These results were used in conjunction with past research to form reliable conclusions.

  19. High Temperature Sodium Thermal Convection Test Loop

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A project for the evaluation of compatibility characteristic of structural materials used in China experimental fast reactor(CEFR) has been in operation. The conditions which these structural materials contact with liquid sodium in reactor can be simulated by the tests in high temperature sodium thermal convection test loop. The main aims of designing and constructing the thermal convection test loop is for the corrosion test of CEFR materials, and the objective is to obtain the corrosion data of domestic materials.The main features of the test loop are shown in Fig.1. The primary components of the loop

  20. LOW SODIUM DIET: PROS AND CONS

    Directory of Open Access Journals (Sweden)

    O. M. Drapkina

    2015-01-01

    Full Text Available Currently, there is rather contradictory evidence on the effectiveness of a low sodium diet for the prevention of various diseases. At that, it is a generally accepted fact, that it is necessary to reduce salt intake in order to reduce high blood pressure. An internist should remember that the degree of blood pressure reduction is individual and not always depends on the level of salt intake. Moreover, the low-sodium diet helps to reduce the rate of telomere shortening, thereby slowing down the aging process.

  1. Bleaching of Wool with Sodium Borohydride

    Directory of Open Access Journals (Sweden)

    Duygu Yilmazer, MSc.

    2009-09-01

    Full Text Available An untreated wool fabric was bleached both with sodium borohydride (SBH in the presence of sodium bisulphite (SBS solution and with a commercial H2O2 bleaching method. The concentration effects of SBH and SBS, bleaching time, pH and temperature on SBH bleaching process were investigated. Whiteness, yellowness and alkali solubility results were assessed for both bleaching methods. The results showed that whiteness degrees obtained with SBH bleaching was comparable with that of H2O2 bleaching method; whereas the alkali solubility values of the SBH bleaching was superior to the H2O2 bleaching.

  2. Sodium fast reactors with closed fuel cycle

    CERN Document Server

    Raj, Baldev; Vasudeva Rao, PR 0

    2015-01-01

    Sodium Fast Reactors with Closed Fuel Cycle delivers a detailed discussion of an important technology that is being harnessed for commercial energy production in many parts of the world. Presenting the state of the art of sodium-cooled fast reactors with closed fuel cycles, this book:Offers in-depth coverage of reactor physics, materials, design, safety analysis, validations, engineering, construction, and commissioning aspectsFeatures a special chapter on allied sciences to highlight advanced reactor core materials, specialized manufacturing technologies, chemical sensors, in-service inspecti

  3. Analysis of Nitrogen in Sodium by Spectrophotometry

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Sodium sample in which nitrogen exists in form of sodium nitride, lithium nitride and calcium nitrideis solved by distilled water and produce ammonia. Ammonia is relieved when solution is heated, then it isabsorbed by hydrochloric acid to produce ammnium chloride. In alkaline solution, ammonium chlorideconverts into ammonia. Ammonia reacts with hypochlorite and phenol that produces a blue indophenol.Nitrogen is determined by 751G type spectrophotometry at the absorption wavelength of 635 nm. The work condition of 751G type spectroscopy, colorimetric condition, smicture of the apparatus

  4. LOW SODIUM DIET: PROS AND CONS

    Directory of Open Access Journals (Sweden)

    O. M. Drapkina

    2015-09-01

    Full Text Available Currently, there is rather contradictory evidence on the effectiveness of a low sodium diet for the prevention of various diseases. At that, it is a generally accepted fact, that it is necessary to reduce salt intake in order to reduce high blood pressure. An internist should remember that the degree of blood pressure reduction is individual and not always depends on the level of salt intake. Moreover, the low-sodium diet helps to reduce the rate of telomere shortening, thereby slowing down the aging process.

  5. Green synthesis of gold nanoparticles reduced and stabilized by sodium glutamate and sodium dodecyl sulfate.

    Science.gov (United States)

    Cabrera, Gil Felicisimo S; Balbin, Michelle M; Eugenio, Paul John G; Zapanta, Charleo S; Monserate, Juvy J; Salazar, Joel R; Mingala, Claro N

    2017-03-18

    The Turkevich method has been used for many years in the synthesis of gold nanoparticles. Lately, the use of plant extracts and amino acids has been reported, which is valuable in the field of biotechnology and biomedicine. The AuNPs was synthesized from the reduction of HAuCl4 3H2O by sodium glutamate and stabilized with sodium dodecyl sulfate. The optimum concentrations for sodium glutamate and sodium dodecyl sulfate in the synthesis process were determined. The characteristics of the synthesized AuNPs was analysed through UV-Vis Spectroscopy and SEM. The AuNPs have spherical shape with a mean diameter of approximately 21.62 ± 4.39 nm and is well dispersed. FTIR analysis of the AuNPs reflected that the sulfate head group of sodium dodecyl sulfate is adsorbed at the surface of the AuNPs. Thus, we report herein the synthesis of AuNPs using sodium glutamate and sodium dodecyl sulfate. Copyright © 2017 Elsevier Inc. All rights reserved.

  6. Impact Of Sodium Oxalate, Sodium Aluminosilicate, and Gibbsite/Boehmite on ARP Filter Performance

    Energy Technology Data Exchange (ETDEWEB)

    Poirier, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-11-01

    The Savannah River Site (SRS) is currently treating radioactive liquid waste with the Actinide Removal Process (ARP) and the Modular Caustic Side Solvent Extraction Unit (MCU). Recently, the low filter flux through the ARP of approximately 5 gallons per minute has limited the rate at which radioactive liquid waste can be treated. Salt Batch 6 had a lower processing rate and required frequent filter cleaning. Savannah River Remediation (SRR) has a desire to understand the causes of the low filter flux and to increase ARP/MCU throughput. SRR requested SRNL to conduct bench-scale filter tests to evaluate whether sodium oxalate, sodium aluminosilicate, or aluminum solids (i.e., gibbsite and boehmite) could be the cause of excessive fouling of the crossflow or secondary filter at ARP. The authors conducted the tests by preparing slurries containing 6.6 M sodium Salt Batch 6 supernate, 2.5 g MST/L slurry, and varying concentrations of sodium oxalate, sodium aluminosilicate, and aluminum solids, processing the slurry through a bench-scale filter unit that contains a crossflow primary filter and a dead-end secondary filter, and measuring filter flux and transmembrane pressure as a function of time. Among the conclusions drwn from this work are the following: (1) All of the tests showed some evidence of fouling the secondary filter. This fouling could be from fine particles passing through the crossflow filter. (2) The sodium oxalate-containing feeds behaved differently from the sodium aluminosilicate- and gibbsite/boehmite-containing feeds.

  7. Wound healing evaluation of sodium fucidate-loaded polyvinylalcohol/sodium carboxymethylcellulose-based wound dressing.

    Science.gov (United States)

    Lee, Jeong Hoon; Lim, Soo-Jeong; Oh, Dong Hoon; Ku, Sae Kwang; Li, Dong Xun; Yong, Chul Soon; Choi, Han-Gon

    2010-07-01

    The cross-linked hydrogel films containing sodium fucidate were previously reported to be prepared polyvinyl alcohol (PVA) and sodium carboxymethylcellulose (Na-CMC) using the freeze-thawing method and their physicochemical property was investigated. For the development of novel sodium fucidate-loaded wound dressing, here its in vivo wound healing test and histopathology were performed compared with the conventional ointment product. In wound healing test, the sodium fucidate-loaded composed of 2.5% PVA, 1.125% Na-CMC and 0.2% drug showed faster healing of the wound made in rat dorsum than the hydrogel without drug, indicating the potential healing effect of sodium fucidate. Furthermore, from the histological examination, the healing effect of sodium fucidate-loaded hydrogel was greater than that of the conventional ointment product and hydrogel without drug, since it might gave an adequate level of moisture and build up the exudates on the wound area. Thus, the sodium fucidate-loaded wound dressing composed of 5% PVA, 1.125% Na-CMC and 0.2% drug is a potential wound dressing with excellent wound healing.

  8. Restraining Sodium Volatilization in the Ferric Bauxite Direct Reduction System

    Directory of Open Access Journals (Sweden)

    Wentao Hu

    2016-03-01

    Full Text Available Direct reduction is an emerging utilization technology of ferric bauxite. However, it requires much more sodium carbonate than ordinary bauxite does. The volatilization is one of the most significant parts of sodium carbonate consumption, as reported in previous studies. Based on the new direct reduction method for utilization of ferric bauxite, this paper has systematically investigated factors including heating temperature, heating time, and sodium carbonate dosage influencing sodium volatilization. For the purpose of reducing sodium volatilization, the Box–Benhken design was employed, and the possibility of separating iron and sodium after direct reduction was also investigated.

  9. Inhibition of neutrophil and eosinophil induced chemotaxis by nedocromil sodium and sodium cromoglycate.

    Science.gov (United States)

    Bruijnzeel, P. L.; Warringa, R. A.; Kok, P. T.; Kreukniet, J.

    1990-01-01

    1. Neutrophils and eosinophils infiltrate the airways in association with the allergen-induced late phase asthmatic reaction. Mobilization of these cells takes place via lipid-like and protein-like chemotactic factors. In this study platelet-activating factor (PAF), leukotriene B4 (LTB4), zymosan-activated serum (ZAS) and N-formyl-methionyl-leucyl-phenylalanine (FMLP) were used as illustrative examples of both groups. Chemotaxis was studied in human neutrophils and eosinophils. The inhibitory effects of nedocromil sodium and sodium cromoglycate were evaluated. 2. All chemotactic factors tested attracted neutrophils with the following rank order of activity: ZAS greater than PAF identical to FMLP identical to LTB4. Eosinophils were only mobilized by PAF, LTB4 and ZAS with the following rank order of activity: ZAS greater than PAF greater than LTB4. 3. Nedocromil sodium and sodium cromoglycate were equally active as the PAF antagonist BN 52021 in inhibiting the PAF-induced chemotaxis of neutrophils (IC50 approximately 10(-8) M). Both drugs were also equally active in inhibiting the chemotaxis of neutrophils induced by ZAS (IC50 approximately 10(-7)-10(-6) M), FMLP (IC50 approximately 10(-7) M) and LTB4 (IC50 approximately 10(-6) M). 4. Nedocromil sodium significantly inhibited the chemotaxis of eosinophils induced by PAF (IC50 approximately 10(-6) M) and LTB4 (IC50 approximately 10(-7) M). The inhibitory potency of BN 52021 was similar to that of nedocromil sodium on the PAF-induced chemotaxis of eosinophils. Sodium cromoglycate was incapable of eliciting significant inhibition of these chemotactic responses. However, sodium cromoglycate significantly inhibited the chemotaxis of eosinophils induced by ZAS (IC50 approximately 10(-7) M), whereas nedocromil sodium was ineffective. PMID:2163279

  10. Increased brain tissue sodium concentration in Huntington's Disease - a sodium imaging study at 4 T.

    Science.gov (United States)

    Reetz, Kathrin; Romanzetti, Sandro; Dogan, Imis; Saß, Christian; Werner, Cornelius J; Schiefer, Johannes; Schulz, Jörg B; Shah, N Jon

    2012-10-15

    The neuropathological hallmark of the autosomal dominantly inherited, neurodegenerative disorder Huntington's disease is progressive striatal loss starting several years prior to symptom manifestation. Magnetic resonance (MR) imaging has been widely used to detect altered structure in premanifest and early Huntington's disease. Given that neurodegeneration is likely preceded by substantial neuronal dysfunction, we used in vivo sodium MR imaging, which has been shown to be sensitive to cell death and viability, to investigate cellular and metabolic integrity of Huntington's disease brain tissue. We studied a total of thirteen healthy controls and thirteen Huntington's disease gene carriers (11 manifest and 2 premanifest). The manifest Huntington's disease group was subdivided into stages 1 and 2 according to their Total Functional Capacity scores. Clinical total motor and cognitive scores, as well as calibrated sodium and T1-weighted MR images were obtained with a 4 T Siemens MR scanner. Sodium images were acquired by means of a constant time imaging technique with an ultra-short "echo time". T1-weighted MR images were further analysed with voxel-based morphometry. The absolute total sodium concentration and grey matter values were measured in several Huntington's disease-specific and also non-specific areas. Statistical analysis of variance and Pearson correlation were applied. In Huntington's disease subjects, we found an increase of total sodium concentration of the entire brain compared to controls. Increased total sodium concentration values were found in structurally affected, but also in some non-affected, regions. The highest total sodium concentration values were found in the bilateral caudate, which was associated with caudate grey matter atrophy and CAG repeat length. In all Huntington's disease subjects we further found a profound increase of total sodium concentration in the putamen, pallidum, thalamus, hippocampus, insula, precuneus and occipital

  11. Modeling and Validation of Sodium Plugging for Heat Exchangers in Sodium-cooled Fast Reactor Systems

    Energy Technology Data Exchange (ETDEWEB)

    Ferroni, Paolo [Westinghouse Electric Company LLC, Cranberry Township, PA (United States). Global Technology Development; Tatli, Emre [Westinghouse Electric Company LLC, Cranberry Township, PA (United States); Czerniak, Luke [Westinghouse Electric Company LLC, Cranberry Township, PA (United States); Sienicki, James J. [Argonne National Lab. (ANL), Argonne, IL (United States); Chien, Hual-Te [Argonne National Lab. (ANL), Argonne, IL (United States); Yoichi, Momozaki [Argonne National Lab. (ANL), Argonne, IL (United States); Bakhtiari, Sasan [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-06-29

    The project “Modeling and Validation of Sodium Plugging for Heat Exchangers in Sodium-cooled Fast Reactor Systems” was conducted jointly by Westinghouse Electric Company (Westinghouse) and Argonne National Laboratory (ANL), over the period October 1, 2013- March 31, 2016. The project’s motivation was the need to provide designers of Sodium Fast Reactors (SFRs) with a validated, state-of-the-art computational tool for the prediction of sodium oxide (Na2O) deposition in small-diameter sodium heat exchanger (HX) channels, such as those in the diffusion bonded HXs proposed for SFRs coupled with a supercritical CO2 (sCO2) Brayton cycle power conversion system. In SFRs, Na2O deposition can potentially occur following accidental air ingress in the intermediate heat transport system (IHTS) sodium and simultaneous failure of the IHTS sodium cold trap. In this scenario, oxygen can travel through the IHTS loop and reach the coldest regions, represented by the cold end of the sodium channels of the HXs, where Na2O precipitation may initiate and continue. In addition to deteriorating HX heat transfer and pressure drop performance, Na2O deposition can lead to channel plugging especially when the size of the sodium channels is small, which is the case for diffusion bonded HXs whose sodium channel hydraulic diameter is generally below 5 mm. Sodium oxide melts at a high temperature well above the sodium melting temperature such that removal of a solid plug such as through dissolution by pure sodium could take a lengthy time. The Sodium Plugging Phenomena Loop (SPPL) was developed at ANL, prior to this project, for investigating Na2O deposition phenomena within sodium channels that are prototypical of the diffusion bonded HX channels envisioned for SFR-sCO2 systems. In this project, a Computational Fluid Dynamic (CFD) model capable of simulating the thermal-hydraulics of the SPPL test

  12. Sodium reduction in margarine using NaCl substitutes

    Directory of Open Access Journals (Sweden)

    CARLA GONÇALVES

    2017-08-01

    Full Text Available ABSTRACT Sodium chloride is traditionally used as a food additive in food processing. However, because of its high sodium content, NaCl has been associated with chronic diseases. Margarine is a popular product that is used in several preparations, but it includes high sodium content; therefore, it is among the products whose sodium content should be reduced. Thus, the objective of this study was to produce margarines with reduced sodium content prepared using a salt mixture. The following 4 margarine formulations were prepared: Formulation A (control - 0% sodium reduction, Formulation B (20.8% less sodium, Formulation C (33.0% less sodium and Formulation D (47.4% less sodium. The low sodium formulations were produced using a salt mixture consisting of NaCl, KCl, and monosodium glutamate at different concentrations. The margarines were evaluated using an acceptance test and descriptive tests: time-intensity and temporal dominance of sensations. The mixture used is a good alternative for preparing low sodium margarine because the low sodium formulations feature equal salinity and do not produce a strange or bad taste. Furthermore, it may be possible to prepare margarines with up to 47.4% less sodium and that are acceptable to consumers.

  13. Sodium reduction in margarine using NaCl substitutes.

    Science.gov (United States)

    Gonçalves, Carla; Rodrigues, Jéssica; Júnior, Heraldo; Carneiro, João; Freire, Tassyana; Freire, Luísa

    2017-08-17

    Sodium chloride is traditionally used as a food additive in food processing. However, because of its high sodium content, NaCl has been associated with chronic diseases. Margarine is a popular product that is used in several preparations, but it includes high sodium content; therefore, it is among the products whose sodium content should be reduced. Thus, the objective of this study was to produce margarines with reduced sodium content prepared using a salt mixture. The following 4 margarine formulations were prepared: Formulation A (control - 0% sodium reduction), Formulation B (20.8% less sodium), Formulation C (33.0% less sodium) and Formulation D (47.4% less sodium). The low sodium formulations were produced using a salt mixture consisting of NaCl, KCl, and monosodium glutamate at different concentrations. The margarines were evaluated using an acceptance test and descriptive tests: time-intensity and temporal dominance of sensations. The mixture used is a good alternative for preparing low sodium margarine because the low sodium formulations feature equal salinity and do not produce a strange or bad taste. Furthermore, it may be possible to prepare margarines with up to 47.4% less sodium and that are acceptable to consumers.

  14. 21 CFR 582.3733 - Sodium benzoate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium benzoate. 582.3733 Section 582.3733 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  15. 21 CFR 582.3784 - Sodium propionate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium propionate. 582.3784 Section 582.3784 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  16. 21 CFR 182.3795 - Sodium sorbate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium sorbate. 182.3795 Section 182.3795 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives § 182.3795...

  17. 21 CFR 582.3766 - Sodium metabisulfite.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium metabisulfite. 582.3766 Section 582.3766 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  18. 21 CFR 582.3798 - Sodium sulfite.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium sulfite. 582.3798 Section 582.3798 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  19. 21 CFR 582.3739 - Sodium bisulfite.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium bisulfite. 582.3739 Section 582.3739 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  20. 21 CFR 182.3739 - Sodium bisulfite.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium bisulfite. 182.3739 Section 182.3739 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  1. 21 CFR 582.3795 - Sodium sorbate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium sorbate. 582.3795 Section 582.3795 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  2. 21 CFR 182.3798 - Sodium sulfite.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium sulfite. 182.3798 Section 182.3798 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives § 182.3798...

  3. 21 CFR 182.3766 - Sodium metabisulfite.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium metabisulfite. 182.3766 Section 182.3766 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  4. The antimicrobial activity of sodium lactate

    NARCIS (Netherlands)

    Houtsma, P.C.

    1996-01-01


    In this thesis, the action spectrum and mechanism of microbial growth inhibition by sodium lactate were examined, with special emphasis on its use in meat products.

    The concentrations (mM) of lactate needed to prevent growth of various spoilage organisms and pathogens in a broth

  5. Chloride binding site of neurotransmitter sodium symporters

    DEFF Research Database (Denmark)

    Kantcheva, Adriana Krassimirova; Quick, Matthias; Shi, Lei

    2013-01-01

    Neurotransmitter:sodium symporters (NSSs) play a critical role in signaling by reuptake of neurotransmitters. Eukaryotic NSSs are chloride-dependent, whereas prokaryotic NSS homologs like LeuT are chloride-independent but contain an acidic residue (Glu290 in LeuT) at a site where eukaryotic NSSs...

  6. Fused deposition modelling of sodium caseinate dispersions

    NARCIS (Netherlands)

    Schutyser, M.A.I.; Houlder, S.; Wit, de Martin; Buijsse, C.A.P.; Alting, A.C.

    2017-01-01

    Only recently, researchers have started experimenting with 3D printing of foods. The aim of this study was to investigate 3D printed objects from sodium caseinate dispersions, exhibiting reversible gelation behaviour. Gelation and dispensing behaviour were explored and structures of different pro

  7. Sodium Alanate Nanoparticles for Hydrogen Storage

    NARCIS (Netherlands)

    Baldé, C.P.

    2008-01-01

    Preparation and characterization of sodium alanate (NaAlH4) based hydrogen storage materials are described in this book. The effect of the NaAlH4 particle size, particularly in the nanometer size range deposited on carbon materials, will be linked to the hydrogen storage characteristics. Moreover, r

  8. Sodium Valproate Withdrawal Correlates with Reduced Aggression

    Science.gov (United States)

    Pritchard, Duncan; Hoerger, Marguerite; Dyer, Tim; Graham, Nicola; Penney, Heather; Mace, F. Charles

    2014-01-01

    People with learning disabilities are sometimes prescribed psychotropic medication to help manage their challenging behaviour. This case study describes how a multicomponent behavioural intervention in conjunction with the systematic withdrawal of sodium valproate was strongly correlated with reduced aggression. No symptoms of bipolar disorder or…

  9. Mixed cation effect in sodium aluminosilicate glasses

    DEFF Research Database (Denmark)

    Kjeldsen, Jonas; Smedskjær, Morten Mattrup; Mauro, John C.

    , network structure, and the resistances associated with the deformation processes in mixed cation glasses by partially substituting magnesium for calcium and calcium for lithium in sodium aluminosilicate glasses. We use Raman and 27Al NMR spectroscopies to obtain insights into the structural...

  10. Sodium Magnetic Resonance Imaging: Biomedical Applications

    CERN Document Server

    Madelin, Guillaume

    2012-01-01

    In this article, we present an up-to-date overview of the potential biomedical applications of sodium MRI in vivo. Sodium MRI is a subject of increasing interest in translational research as it can give some direct and quantitative biochemical information on the tissue viability, cell integrity and function, and therefore not only help the diagnosis but also the prognosis of diseases and treatment outcomes. It has already been applied in vivo in most of human tissues, such as brain for stroke or tumor detection and therapeutic response, in breast cancer, in articular cartilage, in muscle and in kidney, and it was shown in some studies that it could provide very useful new information not available through standard proton MRI. However, this technique is still very challenging due to the low detectable sodium signal in biological tissue with MRI and hardware/software limitations of the clinical scanners. The article is divided in three parts: (1) the role of sodium in biological tissues, (2) a short review on s...

  11. The antimicrobial activity of sodium lactate.

    NARCIS (Netherlands)

    Houtsma, P.C.

    1996-01-01

    In this thesis, the action spectrum and mechanism of microbial growth inhibition by sodium lactate were examined, with special emphasis on its use in meat products.The concentrations (mM) of lactate needed to prevent growth of various spoilage organisms and pathogens in a broth were determined and c

  12. 21 CFR 186.1771 - Sodium palmitate.

    Science.gov (United States)

    2010-04-01

    ..., CAS Reg. No. 408-35-5) is the sodium salt of palmitic acid (hexadecanoic acid). It exists as a white... hydroxide and palmitic acid. (b) In accordance with § 186.1(b)(1), the ingredient is used as a...

  13. Positron Impact Mransitions of Atomic Sodium

    Institute of Scientific and Technical Information of China (English)

    CHENG Yong-Jun; ZHOU YarJun

    2011-01-01

    @@ We present a new investigation of elastic and inelastic positron-sodium scattering by using the coupled-channel optical method(CCO)at an incident energy region of 2-100eV.The ionization continuum and positronium formation channels have been included via a complex equivalent-local optical potential.The present calculations are compared with available theoretical data and our investigation indicates that the inclusion of ionization and Ps-formation channels in the present calculations has a significant effect on the cross sections of elastic and inelastic positron-sodium scattering at lower energies.%We present a new investigation of elastic and inelastic positron-sodium scattering by using the coupled-channel optical method (CCO) at an incident energy region of 2-100eV. The ionization continuum and positronium formation channels have been included via a complex equivalent-local optical potential. The present calculations are compared with available theoretical data and our investigation indicates that the inclusion of ionization and Ps-formation channels in the present calculations has a significant effect on the cross sections of elastic and inelastic positron-sodium scattering at lower energies.

  14. Decomposition of supersaturated sodium aluminate solution

    Institute of Scientific and Technical Information of China (English)

    陈启元; 李洁; 尹周澜; 张平民

    2003-01-01

    The decomposition of supersaturated sodium aluminate solution in the process of alumina production was reviewed. Some fundamental problems, such as the structure of supersaturated sodium aluminate solution and the growth unit of gibbsite precipitation as well as the decomposition mechanism of sodium aluminate solution, were investigated by model analytic technique and theoretical calculation. It is found that the main Al-contained species is S4 symmetric [Al(OH)4(H2O)4]-. [Na+(H2O)4*Al(OH)-4] is found to form in intermediate concentrated solution while [Na+(H2O)2*Al(OH)-4] in highly concentrated solution. Meanwhile, it is proved that [(H2O)2Al(OH)4]- is the basic growth unit of gibbsite and [Al6(OH)18(H2O)6] is a favorable growth unit. Based on above results and ab initio quantum mechanical calculation and transition state theory, a reaction pathway of the decomposition of supersaturated sodium aluminate solution was put forward, in which the transformation of pentacoordinate aluminates ion to hexacoordinate basic growth unit as well as the formation of circled growth unit [Al6(OH)22(H2O)2]4- are the controlling steps.

  15. CHEMICAL ANALYSES OF SODIUM SYSTEMS FINAL REPORT

    Energy Technology Data Exchange (ETDEWEB)

    Greenhalgh, W. O.; Yunker, W. H.; Scott, F. A.

    1970-06-01

    BNWL-1407 summarizes information gained from the Chemical Analyses of Sodium Systems Program pursued by Battelle- Northwest over the period from July 1967 through June 1969. Tasks included feasibility studies for performing coulometric titration and polarographic determinations of oxygen in sodium, and the development of new separation techniques for sodium impurities and their subsequent analyses. The program was terminated ahead of schedule so firm conclusions were not obtained in all areas of the work. At least 40 coulometric titrations were carried out and special test cells were developed for coulometric application. Data indicated that polarographic measurements are theoretically feasible, but practical application of the method was not verified. An emission spectrographic procedure for trace metal impurities was developed and published. Trace metal analysis by a neutron activation technique was shown to be feasible; key to the success of the activation technique was the application of a new ion exchange resin which provided a sodium separation factor of 10{sup 11}. Preliminary studies on direct scavenging of trace metals produced no conclusive results.

  16. Characterization and monitoring of 300 Area facility liquid waste streams: 1994 Annual report

    Energy Technology Data Exchange (ETDEWEB)

    Riley, R.G.; Ballinger, M.Y.; Damberg, E.G.; Evans, J.C.; Julya, J.L.; Olsen, K.B.; Ozanich, R.M.; Thompson, C.J.; Vogel, H.R.

    1995-04-01

    This report summarizes the results of characterizing and monitoring the following sources during calendar year 1994: liquid waste streams from Buildings 306, 320, 324, 326, 331, and 3720 in the 300 Area of Hanford Site and managed by the Pacific Northwest Laboratory; treated and untreated Columbia River water (influent); and water at the confluence of the waste streams (that is, end-of-pipe). Data were collected from March to December before the sampling system installation was completed. Data from this initial part of the program are considered tentative. Samples collected were analyzed for chemicals, radioactivity, and general parameters. In general, the concentrations of chemical and radiological constituents and parameters in building wastewaters which were sampled and analyzed during CY 1994 were similar to historical data. Exceptions were the occasional observances of high concentrations of chloride, nitrate, and sodium that are believed to be associated with excursions that were occurring when the samples were collected. Occasional observances of high concentrations of a few solvents also appeared to be associated with infrequent building r eases. During calendar year 1994, nitrate, aluminum, copper, lead, zinc, bis(2-ethylhexyl) phthalate, and gross beta exceeded US Environmental Protection Agency maximum contaminant levels.

  17. Activity, stability and kinetic parameters for -chymotrypsin catalysed reactions in AOT/isooctane reverse micelles with nonionic and zwitterionic mixed surfactants

    Indian Academy of Sciences (India)

    Santosh Kumar Verma; Kallol K Ghosh

    2013-07-01

    Reverse micelles (RMs) of sodium 1,4-bis(2-ethylhexyl)sulphosuccinate (AOT) in nonpolar organic solvents are widely known to have very high solubilization power for water. The method is applied to the hydrolysis of -nitrophenyl acetate (PNPA) catalysed by -chymotrypsin (-CT) in AOT/isooctane/buffer RMs. The increase in -CT activity and stability was an optimum at wo ([H2O]/[AOT]) = 10, z [Isooctane]/[AOT]) = 5. Three typical surfactants were selected based on their head group charges: a non-ionic surfactant Triton-X 100 and two zwitterionic sulphobetaine surfactants of the type CH2+1N+Me2 (CH2)3 SO$^{−}_{3}$ (n = 10; SB3-10, n = 16; SB3-16). The kinetic parameters (such as cat and M) of the -CT at 27°C were determined and compared in the absence and presence of three surfactants. The effect of chain length of zwitterionic surfactant (SB3-10 and SB3-16) on the enzymatic efficacy of -CT as a function of mixed surfactant addition has been investigated in AOT/isooctane RMs at pH 7.75.

  18. A novel sensor for monitoring of iron(III) ions based on porphyrins.

    Science.gov (United States)

    Vlascici, Dana; Fagadar-Cosma, Eugenia; Popa, Iuliana; Chiriac, Vlad; Gil-Agusti, Mayte

    2012-01-01

    Three A(3)B porphyrins with mixed carboxy-, phenoxy-, pyridyl-, and dimethoxy-substituent functionalization on the meso-phenyl groups were obtained by multicomponent synthesis, fully characterized and used as ionophores for preparing PVC-based membrane sensors selective to iron(III). The membranes have an ionophore:PVC:plasticizer composition ratio of 1:33:66. Sodium tetraphenylborate was used as additive (20 mol% relative to ionophore). The performance characteristics (linear concentration range, slope and selectivity) of the sensors were investigated. The best results were obtained for the membrane based on 5-(4-carboxyphenyl)-10,15,20-tris(4-phenoxyphenyl)-porphyrin plasticized with bis(2-ethylhexyl)sebacate, in a linear range from 1 × 10(-7)-1 × 10(-1) M with a slope of 21.6 mV/decade. The electrode showed high selectivity with respect to alkaline and heavy metal ions and a response time of 20 s. The influence of pH on the sensor response was studied. The sensor was used for a period of six weeks and the utility has been tested for the quantitative determination of Fe(III) in recovered solutions from spent lithium ion batteries and for the quantitative determination of Fe(III) in tap water samples.

  19. A Novel Sensor for Monitoring of Iron(III) Ions Based on Porphyrins

    Science.gov (United States)

    Vlascici, Dana; Fagadar-Cosma, Eugenia; Popa, Iuliana; Chiriac, Vlad; Gil-Agusti, Mayte

    2012-01-01

    Three A3B porphyrins with mixed carboxy-, phenoxy-, pyridyl-, and dimethoxy-substituent functionalization on the meso-phenyl groups were obtained by multicomponent synthesis, fully characterized and used as ionophores for preparing PVC-based membrane sensors selective to iron(III). The membranes have an ionophore:PVC:plasticizer composition ratio of 1:33:66. Sodium tetraphenylborate was used as additive (20 mol% relative to ionophore). The performance characteristics (linear concentration range, slope and selectivity) of the sensors were investigated. The best results were obtained for the membrane based on 5-(4-carboxyphenyl)-10,15,20-tris(4-phenoxyphenyl)-porphyrin plasticized with bis(2-ethylhexyl)sebacate, in a linear range from 1 × 10−7–1 × 10−1 M with a slope of 21.6 mV/decade. The electrode showed high selectivity with respect to alkaline and heavy metal ions and a response time of 20 s. The influence of pH on the sensor response was studied. The sensor was used for a period of six weeks and the utility has been tested for the quantitative determination of Fe(III) in recovered solutions from spent lithium ion batteries and for the quantitative determination of Fe(III) in tap water samples. PMID:22969395

  20. Polymeric plasticizer extends the lifetime of PVC-membrane ion-selective electrodes.

    Science.gov (United States)

    Zahran, Elsayed M; New, Andrea; Gavalas, Vasilis; Bachas, Leonidas G

    2014-02-21

    The nature of the plasticizer plays a pivotal role in the analytical performance of polymer membrane ion sensors. Conventional plasticizers suffer leaching or migration from the membrane and exudation, both of which could limit the lifetime of sensors based on plasticized membranes. Herein, we describe the use of polyester sebacate (PES), a model polymeric plasticizer, in the preparation of poly (vinyl chloride) (PVC) membrane ion-selective electrodes (ISEs) using valinomycin as ionophore. PVC membrane electrodes plasticized with polyester sebacate demonstrated potentiometric response characteristics that compared favorably to ones plasticized with the conventional and similarly structured plasticizer bis(2-ethylhexyl) sebacate (DOS). Increasing the content of polyester sebacate in the membrane enhanced the response and improved the selectivity of valinomycin-based ISEs toward potassium over sodium. Various methods, including electrochemical impedance spectroscopy, UV-vis spectroscopy, dark field optical microscopy, and potentiometry were employed to study the effect of plasticizer on the leaching of the membrane components and the lifetime of both DOS- and PES-plasticized membranes. PES-plasticized electrodes maintained Nernstian response and high selectivity for more than four months, an improvement over DOS-plasticized membrane electrodes. This was attributed to enhanced retention of the membrane components because of the high polymeric nature of the polyester sebacate. These characteristics suggest that polyester sebacate is a good candidate to replace the conventional plasticizers in preparing PVC membrane electrodes with longer lifetime.

  1. Mutual separation of americium(III) and europium(III) using glycolamic acid and thioglycolamic acid

    Energy Technology Data Exchange (ETDEWEB)

    Suneesh, A.S.; Venkatesan, K.A.; Syamala, K.V.; Antony, M.P.; Vasudeva Rao, P.R. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Fuel Chemistry Div.

    2012-07-01

    The extractants, bis(2-ethylhexyl)diglycolamicacid (HDEHDGA) and bis(2-ethylhexy)thiodiglycolamic acid (HDEHSDGA) were synthesized and characterized by {sup 1}H and {sup 13}C NMR, mass and IR spectroscopy. The extraction behaviour of {sup (152+154})Eu(III) and {sup 241}Am(III) from nitric acid medium by a solution of HDEHDGA (or HDEHSDGA) in n-dodecane (n-DD) was studied for the mutual separation of actinides and lanthanides. The effect of various parameters such as the pH, concentrations of HDEHDGA, HDEHSDGA, sodium nitrate, N,N,N',N'-tetrakis(2-pyridylmethyl)ethylenediamine (TPEN) and diethylenetriaminepentaacetic acid (DTPA) on the separation factor (SF) of americium(III) over europium(III) and vice versa was studied, and the conditions needed for the preferential separation were optimised. The results show that HDEHDGA exhibits higher extraction for {sup (152+154)}Eu(III) and HDEHSDGA shows the superior selectivity for {sup 241}Am(III). (orig.)

  2. 恒电位自动滴定法分析脂肪酶水解活性影响因素%Factors Affecting Lipase Activity Assay by Automatic pH-Stat Potentiometric Titration Method

    Institute of Scientific and Technical Information of China (English)

    赵炜; 黄卓楠; 李娜

    2011-01-01

    An accurate quantitative analytical method of lipase activity was established. The activity of Candida rugosa lipase (CRL) in the hydrolysis reaction of olive oil was analyzed by automatic pH-stat potentiometric titration method. Various factors influencing lipase activity assay were discussed and appropriate analysis conditions were selected. The results showed that the hydrolytic activity of CRL was linearly proportional to enzyme protein concentration only within 0.01-0.07 g/L range of protein concentration at 37 ℃. The corresponding range of enzyme activity was 1-14 μmol/min. Kinetics studies showed that the corresponding values of Km and Vmax were 4.828×10-4 mol/L and 3.498×10-3 mol/min, respectively. The optimum temperature, pH value and stirring speed were 37 ℃ 7. 2 and 1200 r/min, respectively. Low content of polyvingl alcohol (PVA) and lecithin promoted CRL activity but high content of them inhibited CRL activity. The maximum relative activity of CRL reached to 297% at 2.0 g/L of PVA or 154% at 5.0 g/L of lecithin in the system. PVA and lecithin showed inhibiting effect on CRL activity at more than 4.0 g/L and 10.0 g/L of content, respectively.In contrast, low concentration of AOT restrained CRL activity, while high concentration of it (more than 12.5 g/L) enhanced CRL activity. The maximum relative activity of CRL reached to 255% at 50g/L of AOT in the system. Tween-80 significantly inhibited CRL activity. A several of imidazole ionic liquids improved CRL activity greatly in sequence of[OMIM][Br] 〉[BMIM][Br]>[EMIM][Br]>[OMIM][BF4]>[BMIM][BF4 ]>[EMIM] [BF4 ]. The maximum relative activity of CRL reached to1734%, 1709%, 1579%, 1063%, 1030% and 960% with 12, 43, 90, 5, 45 and 88 g/L of corresponding concentration of the ionic liquids, respectively. The promotion effect of the ionic liquids on CRL activity were much better than those of PVA, lecithin and bis(2-ethylhexyl)sulfosuccinate sodium (AOT). The impact of anions in

  3. Sodium sulfide leaching of low-grade jamesonite concentrate in production of sodium pyroantimoniate

    Institute of Scientific and Technical Information of China (English)

    YANG Tian-zu; JIANG Ming-xi; LAI Qiong-lin; CHEN Jin-zhong

    2005-01-01

    Sodium sulfide leaching of a low-grade jamesonite concentrate in the production of sodium pyroantimoniate through the air oxidation process and the influencing factors on the leaching rate of antimony were investigated.In order to decrease the consumption of sodium sulfide and increase the concentration of antimony in the leaching solution, two-stage leaching of jamesonite concentrate and combination leaching of high-grade stibnite concentrate and jamesonite concentrate were used. The experimental results showthat the consumptions of sodium sulfide for the two-stage leaching process and the combination leaching process are decreased by 20% and 60% compared to those of one-stage leaching process respectively. The final concentrations of antimony in the leaching solutions of both processes are above 100 g/L.

  4. Cementing properties of steel slag activated by sodium silicates and sodium hydroxide

    Institute of Scientific and Technical Information of China (English)

    Wen Ni; En Wang; Jianping Li; Han Sun

    2005-01-01

    Steel slag which is mainly composed of γ-CasSiO4 and other silicates or alumino-silicates is activated by sodium silicates and sodium hydroxide. The powders of such steel slag are usually inert to hydrate and subsequently have very low ability of cementing. But when sodium silicates and sodium hydroxide are used as activators the steel slag shows very good properties of cementing. When activated with NaOH solution the hardened slurry of the steel slag has a compressive strength of 11.13 MPa after being cured for 28 days. When activated with Na2SiO3 solution the samples after being cured for 28 days have an average compressive strength of 40.23 MPa. While the steel slag slurry which is only mixed with water has a compressive of 0.88 MPa after being cured for 28 days.

  5. Sodium MRI in human heart: a review.

    Science.gov (United States)

    Bottomley, Paul A

    2016-02-01

    This paper offers a critical review of the properties, methods and potential clinical application of sodium ((23)Na) MRI in human heart. Because the tissue sodium concentration (TSC) in heart is about ~40 µmol/g wet weight, and the (23)Na gyromagnetic ratio and sensitivity are respectively about one-quarter and one-11th of that of hydrogen ((1)H), the signal-to-noise ratio of (23)Na MRI in the heart is about one-6000th of that of conventional cardiac (1)H MRI. In addition, as a quadrupolar nucleus, (23)Na exhibits ultra-short and multi-component relaxation behavior (T1 ~ 30 ms; T2 ~ 0.5-4 ms and 12-20 ms), which requires fast, specialized, ultra-short echo-time MRI sequences, especially for quantifying TSC. Cardiac (23)Na MRI studies from 1.5 to 7 T measure a volume-weighted sum of intra- and extra-cellular components present at cytosolic concentrations of 10-15 mM and 135-150 mM in healthy tissue, respectively, at a spatial resolution of about 0.1-1 ml in 10 min or so. Currently, intra- and extra-cellular sodium cannot be unambiguously resolved without the use of potentially toxic shift reagents. Nevertheless, increases in TSC attributable to an influx of intra-cellular sodium and/or increased extra-cellular volume have been demonstrated in human myocardial infarction consistent with prior animal studies, and arguably might also be seen in future studies of ischemia and cardiomyopathies--especially those involving defects in sodium transport. While technical implementation remains a hurdle, a central question for clinical use is whether cardiac (23)Na MRI can deliver useful information unobtainable by other more convenient methods, including (1)H MRI.

  6. Epithelial Sodium and Chloride Channels and Asthma

    Institute of Scientific and Technical Information of China (English)

    Wen Wang; Hong-Long Ji

    2015-01-01

    Objective:To focus on the asthmatic pathogenesis and clinical manifestations related to epithelial sodium channel (ENaC)/chlorine ion channel.Data Sources:The data analyzed in this review were the English articles from 1980 to 2015 from journal databases,primarily PubMed and Google Scholar.The terms used in the literature search were:(1) ENaCs;cystic fibrosis (CF) transmembrane conductance regulator (CFTR);asthma/asthmatic,(2) ENaC/sodium salt;CF;asthma/asthmatic,(3) CFTR/chlorine ion channels;asthma/asthmatic,(4) ENaC/sodium channel/scnn1a/scnn1b/scnn1g/scnn1d/amiloride-sensitive/amiloride-inhibtable sodium channels/sodium salt;asthma/asthmatic,lung/pulmonary/respiratory/tracheal/alveolar,and (5) CFTR;CF;asthma/asthmatic (ti).Study Selection:These studies included randomized controlled trials or studies covering asthma pathogenesis and clinical manifestations related to ENaC/chlorine ion channels within the last 25 years (from 1990 to 2015).The data involving chronic obstructive pulmonary disease and CF obtained from individual studies were also reviewed by the authors.Results:Airway surface liquid dehydration can cause airway inflammation and obstruction.ENaC and CFTR are closely related to the airway mucociliary clearance.Ion transporters may play a critical role in pathogenesis of asthmatic exacerbations.Conclusions:Ion channels have been the center of many studies aiming to understand asthmatic pathophysiological mechanisms or to identify therapeutic targets for better control of the disease.

  7. Antiorthostatic immobilization with varied sodium intake

    Science.gov (United States)

    Hinghofer-Szalkay, H.; Haditsch, B.; Pilz, K.; Rössler, A.; Laszlo, Z.

    The study investigated, in 10 normotensive male persons, heart rate responses to graded lower body suction (LBNP) with adaptation to various oral sodium clamping during both ambulatory (AMB) conditions for 4 days, and thereafter to additional antiorthostatic (6° head down) positioning. A ,low' (LS: 143+/-10 mM Na +/ d excreted) and a ,high' (HS: 434+/-17 mM Na +/d excreted) sodium treatment - in randomized order and separated =1 mo - followed a ,conditioning' run with moderate sodium (237+/-9 mM Na +/d excreted). Urinary volume and sodium output were monitored, hormone levels (PRA, aldosterone, AVP) determined, and extracellular volume (ECV) estimated by whole body electrical impedance spectroscopy. ECV was not differently reduced (p>0.1) in LS (-5.8+/-2.3%, p=0.018) and HS (-4.0+/-1.0%. p=0.002). Morning AVP was lower (5.5+/-0.1 pg/ml) in HS than in LS (7.2+/-0.3 pg/ml; N=7 days), as well as aldosterone (69+/-7 pg/ml in HS vs. 180+/-24 pg/ml in LS). LBNP dose responses of PRA and aldosterone were higher in LS than HS after 8 days AOB, whereas microvascular fluid filtration was unchanged by any experimental condition. Heart rate responses to LBNP were unchanged by sodium supply, whereas mean arterial and pulse pressure was lower in LS than HS during all LBNP intensities. Thus, HS was able to increase arterial blood and pulse pressure and reduced PRA and aldosterone levels during graded simulated orthostatic challenge, but did neither ameliorate AOB-induced ECV decrease nor alter LBNP-induced filtration and heart rate responses. These results are relevant for planning of future countermeasures in astronauts. Supported by the Austrian Research Fund (P13451-MED)

  8. Optimization of Low Sodium Salts Mix for Shoestring Potatoes.

    Science.gov (United States)

    Pereira, Heverton Carrara; de Souza, Vanessa Rios; Azevedo, Natália Csizmar; Rodrigues, Daniela Maria; Nunes, Cleiton Antônio; Pinheiro, Ana Carla Marques

    2015-06-01

    Several studies have shown the close relationship between the sodium consumption and health problems such as hypertension and cardiovascular disease. Thus, the demand for products with reduced sodium content, but with sensory quality, is increasing every day. In this context, this study aimed to optimize a low sodium salts mix using sodium chloride, potassium chloride, and monosodium glutamate to the development of shoestring potatoes with low sodium content and high sensory quality, through mixture design and response surface methodology. The salts mix that promotes the same salting power and similar sensory acceptability that the shoestring potatoes with 1.6% sodium chloride (ideal concentration) and at the same time promotes the greatest possible reduction of sodium, about 65%, should provide the composition as follows: 0.48% of sodium chloride, 0.92% of potassium chloride, and 0.43% of monosodium glutamate.

  9. Efficiency of sodium oxybate in episodic cluster headache.

    Science.gov (United States)

    Hidalgo, Hildegard; Uhl, Verena; Gantenbein, Andreas R; Sándor, Peter S; Kallweit, Ulf

    2013-10-01

    We report the case of a 60-year-old man suffering from episodic cluster headache treated successfully with sodium oxybate. Sodium oxybate may be a therapeutic option in attacks of episodic cluster headache.

  10. TREATMENT OF SODIUM DISORDERS AFTER SURGERY OF CRANIOPHARYNGIOMA

    Institute of Scientific and Technical Information of China (English)

    黄文宇; 石祥恩

    2000-01-01

    Objective. To study the treatment of the patients with blood sodium disorder after cramophatyrgioma stagery.Method. The blood sodium in 44 patients with craniopharyngiomas was daily examined from operative to post-op-erative days. Hypematremia is defined as [Na] > 145 mmol/l, and hyponatremia as [Na] < 135 nmml/L.Results. Of the 44 patients, 36 developed sodium disorder. Among them, simple hyponatremia was 16 patients,simple hypematremia was 9 patients, and alternative sodium disorder was 11 patients. Condusion. The blood sodium disorder in patients with craniopharyngiomas after surgery appears to present com-plicated changes. Three types of blood sodium disorder could be determined as simple hyponatremia, simple hyperna-tremia, and alternative sodium disorder. Treatment of the sodium disorder in patients with craniopharyngiomas after surgery could be carried in accordance with the above three types.

  11. Sodium Picosulfate, Magnesium Oxide, and Anhydrous Citric Acid

    Science.gov (United States)

    Sodium picosulfate, magnesium oxide, and anhydrous citric acid combination powder is used to empty the colon (large ... clear view of the walls of the colon. Sodium picosulfate is in a class of medications called ...

  12. Measurement and Analysis of Sodium Void Reactivity Effect in CEFR

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    The sodium void reactivity effect (SVRE) is one of the important parameters in the design and safety analysis of sodium-cooled fast reactors. In some serious accident conditions, for example the total instantaneous blockage (TIB) accident,

  13. EFFECT OF MONENSIN, SODIUM BICARBONATE AND VITAMIN A ...

    African Journals Online (AJOL)

    These are the feeding of ever increasing levels of grain and the use ... feeding of high grain diets results in the rapid ..... weight gains, efficiency of gains and consumption of rations ... Whole wheat plus sodium buffers or sodium chloride. Austr.

  14. Strategies to reduce sodium intake in the United States

    National Research Council Canada - National Science Library

    Henney, Jane E; Taylor, Christine Lewis; Boon, Caitlin S

    2010-01-01

    "Reducing the intake of sodium is an important public health goal for Americans. Since the 1970s, an array of public health interventions and national dietary guidelines has sought to reduce sodium intake. However, the U.S...

  15. Viscosity and density tables of sodium chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Fair, J.A.; Ozbek, H. (comps.)

    1977-04-01

    A file is presented containing tabulated data extracted from the scientific literature on the density and viscosity of aqueous sodium chloride solutions. Also included is a bibliography of the properties of aqueous sodium chloride solutions. (MHR)

  16. Research on Technology of Filling Sodium into Fuel Test Capsules

    Institute of Scientific and Technical Information of China (English)

    XU; Chi; XIE; Chun; WANG; Shu-xing; MI; Zheng-feng; YU; Tuan-jie; CUI; Chao; WANG; Ming-zheng

    2015-01-01

    In order to provide a high pure sodium environment for properties testing in the fuel research for fast reactor,it is essential to fill sodium into fuel testing capsules.By the method of vacuum,temperature-controlling and inert gas protection,quantificational sodium had been filled into the fuel testing capsules.Fig.1shows the schematic diagram of sodium filling device.Table 1shows

  17. Sodium Borohydride/Hydrogen Peroxide Fuel Cells For Space Application

    Science.gov (United States)

    Valdez, T. I.; Deelo, M. E.; Narayanan, S. R.

    2006-01-01

    This viewgraph presentation examines Sodium Borohydride and Hydrogen Peroxide Fuel Cells as they are applied to space applications. The topics include: 1) Motivation; 2) The Sodium Borohydride Fuel Cell; 3) Sodium Borohydride Fuel Cell Test Stands; 4) Fuel Cell Comparisons; 5) MEA Performance; 6) Anode Polarization; and 7) Electrode Analysis. The benefits of hydrogen peroxide as an oxidant and benefits of sodium borohydride as a fuel are also addressed.

  18. THE SODIUM PREVALENCE IN CARBONATED SOFT DRINKS SOLD IN BRAZIL

    OpenAIRE

    Sandra Fernanda Nunes; Sonia Maria Freire; Maria Margarida Castel-Branco; Isabel Vitória Figueiredo

    2012-01-01

    The carbonated soft drinks intake has changed the children eating habits. This factor may be directly associated with arterial hypertension due the high consumption of sodium present in foods and drinks industrialized. This study was to compare sodium levels between two different types of carbonated soft drinks, carbonated sugar drinks and diet drinks to define what type of drink has the lowest sodium content and alerting healthcare professionals about the presence of sodium in industrialized...

  19. 21 CFR 133.116 - Low sodium cheddar cheese.

    Science.gov (United States)

    2010-04-01

    ... ingredients used as a salt substitute. (d) Low sodium cheddar cheese is subject to § 105.69 of this chapter... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Low sodium cheddar cheese. 133.116 Section 133.116... Cheese and Related Products § 133.116 Low sodium cheddar cheese. Low sodium cheddar cheese is the food...

  20. Attenuation of aspirin-induced bronchoconstriction by sodium cromoglycate and nedocromil sodium.

    Science.gov (United States)

    Robuschi, M; Gambaro, G; Sestini, P; Pieroni, M G; Refini, R M; Vaghi, A; Bianco, S

    1997-04-01

    The protective activity of nedocromil sodium and of sodium cromoglycate against aspirin-induced asthma has never been investigated in controlled studies. Because it has been reported that aspirin-induced platelet-mediated cytotoxic activity in vitro is inhibited after treatment in vivo with nedocromil but not with cromoglycate, we investigated whether these compounds also exhibit a different protective activity against aspirin-induced bronchoconstriction. Ten patients with aspirin-induced asthma underwent three bronchial challenges with a single dose of lysine acetylsalicylate (LASA) that caused a decrease in FEV1 of 25% or more in a preliminary dose-response test 30 min after inhalation of 4 mg nedocromil sodium, 10 mg sodium cromoglycate, or placebo. FEV1 and SRaw were recorded at intervals for 195 min. After placebo, LASA caused a maximal decrease in FEV1 of 42 +/- 4% of baseline. After cromoglycate and nedocromil the maximal decrease in FEV1 was reduced to 20 +/- 3% and 18 +/- 4%, respectively (p sodium cromoglycate and nedocromil sodium are equally effective in attenuating aspirin-induced bronchoconstriction and that it is unlikely that platelet activation participates in the pathogenesis of aspirin-induced asthma.

  1. Survey of the transport properties of sodium superionic conductor materials for use in sodium batteries

    Science.gov (United States)

    Guin, M.; Tietz, F.

    2015-01-01

    One important issue in future scenarios predominantly using renewable energy sources is the electrochemical storage of electricity in batteries. Among all rechargeable battery technologies, Li-ion cells have the largest energy density and output voltage today, but they have yet to be optimized in terms of capacity, safety and cost for use as stationary systems. Recently, sodium batteries have been attracting attention again because of the abundant availability of Na. However, much work is still required in the field of sodium batteries in order to mature this technology. Sodium superionic conductor (NASICON) materials are a thoroughly studied class of solid electrolytes. In this study, their crystal structure, compositional diversity and ionic conductivity are surveyed and analysed in order to correlate the lattice parameters and specific crystal structure data with sodium conductivity and activation energy using as much data sets as possible. Approximately 110 compositions with the general formula Na 1 + 2 w + x - y + zMw(II) Mx(III) My(V) M2- w - x - y (IV) (SiO4)z(PO4) 3 - z were included in the data collection to determine an optimal size for the M cations. In addition, the impact of the amount of Na per formula unit on the conductivity and the substitution of P with Si are discussed. An extensive study of the size of the structural bottleneck for sodium conduction (formed by triangles of oxygen ions) was carried out to validate the influence of this geometrical parameter on sodium conductivity.

  2. [Progress in sodium channelopathies and biological functions of voltage-gated sodium channel blockers].

    Science.gov (United States)

    Wang, Hongyan; Gou, Meng; Xiao, Rong; Li, Qingwei

    2014-06-01

    Voltage-gated sodium channels (VGSCs), which are widely distributed in the excitable cells, are the primary mediators of electrical signal amplification and propagation. They play important roles in the excitative conduction of the neurons and cardiac muscle cells. The abnormalities of the structures and functions of VGSCs can change the excitability of the cells, resulting in a variety of diseases such as neuropathic pain, epilepsy and arrhythmia. At present, some voltage-gated sodium channel blockers are used for treating those diseases. In the recent years, several neurotoxins have been purified from the venom of the animals, which could inhibit the current of the voltage-gated sodium channels. Usually, these neurotoxins are compounds or small peptides that have been further designed and modified for targeted drugs of sodium channelopathies in the clinical treatment. In addition, a novel cysteine-rich secretory protein (CRBGP) has been isolated and purified from the buccal gland of the lampreys (Lampetra japonica), and it could inhibit the Na+ current of the hippocampus and dorsal root neurons for the first time. In the present study, the progress of the sodium channelopathies and the biological functions of voltage-gated sodium channel blockers are analyzed and summarized.

  3. 21 CFR 520.608 - Dicloxacillin sodium monohydrate capsules.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Dicloxacillin sodium monohydrate capsules. 520.608 Section 520.608 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... Dicloxacillin sodium monohydrate capsules. (a) Specifications. Each capsule contains dicloxacillin sodium...

  4. 21 CFR 73.125 - Sodium copper chlorophyllin.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Sodium copper chlorophyllin. 73.125 Section 73.125... COLOR ADDITIVES EXEMPT FROM CERTIFICATION Foods § 73.125 Sodium copper chlorophyllin. (a) Identity. (1) The color additive sodium copper chlorophyllin is a green to black powder prepared from chlorophyll...

  5. 21 CFR 173.325 - Acidified sodium chlorite solutions.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acidified sodium chlorite solutions. 173.325... HUMAN CONSUMPTION Specific Usage Additives § 173.325 Acidified sodium chlorite solutions. Acidified sodium chlorite solutions may be safely used in accordance with the following prescribed conditions: (a...

  6. Sodium Channel (Dys)Function and Cardiac Arrhythmias

    NARCIS (Netherlands)

    C.A. Remme; C.R. Bezzina

    2010-01-01

    P>Cardiac voltage-gated sodium channels are transmembrane proteins located in the cell membrane of cardiomyocytes. Influx of sodium ions through these ion channels is responsible for the initial fast upstroke of the cardiac action potential. This inward sodium current thus triggers the initiation an

  7. 21 CFR 582.1781 - Sodium aluminum phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium aluminum phosphate. 582.1781 Section 582.1781 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Additives § 582.1781 Sodium aluminum phosphate. (a) Product. Sodium aluminum phosphate. (b) Conditions...

  8. 21 CFR 182.1781 - Sodium aluminum phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium aluminum phosphate. 182.1781 Section 182.1781 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Food Substances § 182.1781 Sodium aluminum phosphate. (a) Product. Sodium aluminum phosphate....

  9. 21 CFR 182.6085 - Sodium acid phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium acid phosphate. 182.6085 Section 182.6085 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD... Sodium acid phosphate. (a) Product. Sodium acid phosphate. (b) Conditions of use. This substance...

  10. 21 CFR 522.1883 - Prednisolone sodium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Prednisolone sodium phosphate. 522.1883 Section... § 522.1883 Prednisolone sodium phosphate. (a) Specifications. Each milliliter of solution contains 20 milligrams (mg) prednisolone sodium phosphate (equivalent to 14.88 mg of prednisolone). (b) Sponsor. See...

  11. 21 CFR 582.6085 - Sodium acid phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium acid phosphate. 582.6085 Section 582.6085 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Sodium acid phosphate. (a) Product. Sodium acid phosphate. (b) Conditions of use. This substance...

  12. Sodium and sulfur release and recapture during black liquor burning

    Energy Technology Data Exchange (ETDEWEB)

    Frederick, W.J.; Iisa, K.; Wag, K.; Reis, V.V.; Boonsongsup, L.; Forssen, M.; Hupa, M.

    1995-08-01

    The objective of this study was to provide data on sulfur and sodium volatilization during black liquor burning, and on SO2 capture by solid sodium carbonate and sodium chloride. This data was interpreted and modeled into rate equations suitable for use in computational models for recovery boilers.

  13. 21 CFR 176.320 - Sodium nitrate-urea complex.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium nitrate-urea complex. 176.320 Section 176... Substances for Use Only as Components of Paper and Paperboard § 176.320 Sodium nitrate-urea complex. Sodium nitrate-urea complex may be safely used as a component of articles intended for use in...

  14. Monitoring sodium in commercially processed foods from stores and restaurants

    Science.gov (United States)

    Most of the sodium we eat comes from commercially processed foods from stores and restaurants. Sodium reduction in these foods is a key component of several recent public health efforts. Agricultural Research Service (ARS) of USDA, CDC and FDA have launched a collaborative program to monitor sodium ...

  15. 40 CFR 141.41 - Special monitoring for sodium.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Special monitoring for sodium. 141.41... and Prohibition on Lead Use § 141.41 Special monitoring for sodium. (a) Suppliers of water for... distribution system for the determination of sodium concentration levels; samples must be collected...

  16. Beam-profile monitor using a sodium-vapour

    CERN Multimedia

    1972-01-01

    Beam-profile monitor using a sodium-vapour curtain at 45 degrees to the ISR beam in Ring I (sodium generator is in white cylinder just left of centre). Electrons produced by ionization of the sodium vapour give an image of the beam on a fluorescent screen that is observed by a TV camera (at upper right).

  17. Process for the production of sodium carbonate anhydrate

    NARCIS (Netherlands)

    Oosterhof, H.; Van Rosmalen, G.M.; Witkamp, G.J.; De Graauw, J.

    2000-01-01

    The invention is directed to a process for the production of sodium carbonate-anhydrate having a bulk density of at least 800 kg/m<3>, said process comprising: providing a suspension of solid sodium carbonate and/or solid sodium bicarbonate and/or solid double salts at least comprising one of

  18. 46 CFR 153.1065 - Sodium chlorate solutions.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Sodium chlorate solutions. 153.1065 Section 153.1065... Procedures § 153.1065 Sodium chlorate solutions. (a) No person may load sodium chlorate solutions into a... solutions are immediately washed away. Approval of Surveyors and Handling of Categories A, B, C, and D...

  19. Effect of sodium environment on breeder reactor components

    Energy Technology Data Exchange (ETDEWEB)

    Eichelberger, R.L.; Brehm, W.F.

    1978-01-01

    This paper reviews the interaction phenomena between sodium and reactor materials, and the application to reactor design and operation. Both corrosion and deposition are considered. Sodium removal and decontamination is briefly mentioned, together with some recent developments that are still in the experimental stage. No new theories of sodium-material interaction behavior are offered. 56 references.

  20. Structure-rheology relations in sodium caseinate containing systems

    NARCIS (Netherlands)

    Ruis, H.G.M.

    2007-01-01

    The general aim of the work described in this thesis was to investigate structure-rheologyrelations for dairy related products, focusing on model systems containing sodium caseinate. The acid inducedgelationof sodium caseinate, of sodium caseinate

  1. 21 CFR 181.33 - Sodium nitrate and potassium nitrate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium nitrate and potassium nitrate. 181.33...-Sanctioned Food Ingredients § 181.33 Sodium nitrate and potassium nitrate. Sodium nitrate and potassium nitrate are subject to prior sanctions issued by the U.S. Department of Agriculture for use as sources...

  2. 76 FR 63305 - Approaches To Reducing Sodium Consumption; Public Meeting

    Science.gov (United States)

    2011-10-12

    ... as current and emerging approaches designed to promote sodium reduction. The purpose of the public... review the FDA's Sodium Reduction Web page located at http://www.fda.gov/Food/FoodIngredientsPackaging... to identify opportunities for sodium reduction. II. Purpose and Format of the Meeting If you wish to...

  3. Metabolic attributes, yield and stability of milk in Jersey cows fed diets containing sodium citrate and sodium bicarbonate

    OpenAIRE

    2013-01-01

    The objective of this work was to evaluate the inclusion of sodium citrate and sodium bicarbonate in the diet of lactating Jersey cows, and its effects on the metabolic attributes, productivity and stability of milk. We evaluated urinary pH, levels of glucose and urea in blood, body weight, body condition score, milk yield, milk stability (ethanol test), and milk physicochemical properties of 17 cows fed diets containing sodium citrate (100 g per cow per day), sodium bicarbonate (40 g per cow...

  4. Actions of Ethanol on Voltage-Sensitive Sodium Channels. Effects on Neurotoxin-Stimulated Sodium Uptake in Synaptosomes

    Science.gov (United States)

    1985-01-01

    concentration in the nonaqueuus (membrane) phase (Lyon et aL, 1981). Concentration- effect summarized in table 1 . When sodium channels were activated curves were...Voltage-Sensitive Sodium Channels : Effects on Neurotoxin-Stimulated Sodium Uptake in DT (7 Synaptosomes E L C MICHAEL J. MULLIN’ and WALTER A. HUNT...1984). At the present time, the 8 1 structural and functional properties of the voltage-sensitive sodium channels are understood most completely

  5. Time to Consider Use of the Sodium-to-Potassium Ratio for Practical Sodium Reduction and Potassium Increase.

    Science.gov (United States)

    Iwahori, Toshiyuki; Miura, Katsuyuki; Ueshima, Hirotsugu

    2017-07-05

    Pathogenetic studies have demonstrated that the interdependency of sodium and potassium affects blood pressure. Emerging evidences on the sodium-to-potassium ratio show benefits for a reduction in sodium and an increase in potassium compared to sodium and potassium separately. As presently there is no known review, this article examined the practical use of the sodium-to-potassium ratio in daily practice. Epidemiological studies suggest that the urinary sodium-to-potassium ratio may be a superior metric as compared to separate sodium and potassium values for determining the relation to blood pressure and cardiovascular disease risks. Higher correlations and better agreements are seen for the casual urine sodium-to-potassium ratio than for casual urine sodium or potassium alone when compared with the 24-h urine values. Repeated measurements of the casual urine provide reliable estimates of the 7-day 24-h urine value with less bias for the sodium-to-potassium ratio as compared to the common formulas used for estimating the single 24-h urine from the casual urine for sodium and potassium separately. Self-monitoring devices for the urinary sodium-to-potassium ratio measurement makes it possible to provide prompt onsite feedback. Although these devices have been evaluated with a view to support an individual approach for sodium reduction and potassium increase, there has yet to be an accepted recommended guideline for the sodium-to-potassium ratio. This review concludes with a look at the practical use of the sodium-to-potassium ratio for assistance in practical sodium reduction and potassium increase.

  6. Analysis of the action of lidocaine on insect sodium channels.

    Science.gov (United States)

    Song, Weizhong; Silver, Kristopher S; Du, Yuzhe; Liu, Zhiqi; Dong, Ke

    2011-01-01

    A new class of sodium channel blocker insecticides (SCBIs), which include indoxacarb, its active metabolite, DCJW, and metaflumizone, preferably block inactivated states of both insect and mammalian sodium channels in a manner similar to that by which local anesthetic (LA) drugs block mammalian sodium channels. A recent study showed that two residues in the cockroach sodium channel, F1817 and Y1824, corresponding to two key LA-interacting residues identified in mammalian sodium channels are not important for the action of SCBIs on insect sodium channels, suggesting unique interactions of SCBIs with insect sodium channels. However, the mechanism of action of LAs on insect sodium channels has not been investigated. In this study, we examined the effects of lidocaine on a cockroach sodium channel variant, BgNa(v)1-1a, and determined whether F1817 and Y1824 are also critical for the action of LAs on insect sodium channels. Lidocaine blocked BgNa(v)1-1a channels in the resting state with potency similar to that observed in mammalian sodium channels. Lidocaine also stabilized both fast-inactivated and slow-inactivated states of BgNa(v)1-1a channels, and caused a limited degree of use- and frequency-dependent block, major characteristics of LA action on mammalian sodium channels. Alanine substitutions of F1817 and Y1824 reduced the sensitivity of the BgNa(v)1-1a channel to the use-dependent block by lidocaine, but not to tonic blocking and inactivation stabilizing effects of lidocaine. Thus, similar to those on mammalian sodium channels, F1817 and Y1824 are important for the action of lidocaine on cockroach sodium channels. Our results suggest that the receptor sites for lidocaine and SCBIs are different on insect sodium channels.

  7. Analysis of Design of Sodium Reception and Secondary Loop Sodium Plugging and Removal System for Fast Reactor

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Through comparison of sodium reception and secondary loop sodium plugging and removal system on CEFR with BN-800, the main difference of the two designs is as follows: 1) System division is different. BN-800 can be divided into sodium reception system,

  8. 21 CFR 872.3490 - Carboxymethylcellulose sodium and/or polyvinylmethylether maleic acid calcium-sodium double salt...

    Science.gov (United States)

    2010-04-01

    ... polyvinylmethylether maleic acid calcium-sodium double salt denture adhesive. 872.3490 Section 872.3490 Food and Drugs... DENTAL DEVICES Prosthetic Devices § 872.3490 Carboxymethylcellulose sodium and/or polyvinylmethylether maleic acid calcium-sodium double salt denture adhesive. (a) Identification. A carboxymethylcellulose...

  9. The effect of nedocromil sodium and sodium cromoglycate on antigen-induced bronchoconstriction in the Ascaris-sensitive monkey.

    Science.gov (United States)

    Eady, R. P.; Greenwood, B.; Jackson, D. M.; Orr, T. S.; Wells, E.

    1985-01-01

    Nedocromil sodium inhibited the bronchoconstriction caused by antigen challenge in Ascaris-sensitive monkeys and in addition it prevented the release of histamine from mast cells lavaged from sensitive monkeys. Sodium cromoglycate was relatively inactive in both these systems. It is suggested that nedocromil sodium can stabilize both mucosal and connective tissue mast cells and may represent a new type of drug. PMID:2992657

  10. Final report on the safety assessment of sodium sulfite, potassium sulfite, ammonium sulfite, sodium bisulfite, ammonium bisulfite, sodium metabisulfite and potassium metabisulfite.

    Science.gov (United States)

    Nair, Bindu; Elmore, Amy R

    2003-01-01

    Sodium Sulfite, Ammonium Sulfite, Sodium Bisulfite, Potassium Bisulfite, Ammonium Bisulfite, Sodium Metabisulfite, and Potassium Metabisulfite are inorganic salts that function as reducing agents in cosmetic formulations. All except Sodium Metabisulfite also function as hair-waving/straightening agents. In addition, Sodium Sulfite, Potassium Sulfite, Sodium Bisulfite, and Sodium Metabisulfite function as antioxidants. Although Ammonium Sulfite is not in current use, the others are widely used in hair care products. Sulfites that enter mammals via ingestion, inhalation, or injection are metabolized by sulfite oxidase to sulfate. In oral-dose animal toxicity studies, hyperplastic changes in the gastric mucosa were the most common findings at high doses. Ammonium Sulfite aerosol had an acute LC(50) of >400 mg/m(3) in guinea pigs. A single exposure to low concentrations of a Sodium Sulfite fine aerosol produced dose-related changes in the lung capacity parameters of guinea pigs. A 3-day exposure of rats to a Sodium Sulfite fine aerosol produced mild pulmonary edema and irritation of the tracheal epithelium. Severe epithelial changes were observed in dogs exposed for 290 days to 1 mg/m(3) of a Sodium Metabisulfite fine aerosol. These fine aerosols contained fine respirable particle sizes that are not found in cosmetic aerosols or pump sprays. None of the cosmetic product types, however, in which these ingredients are used are aerosolized. Sodium Bisulfite (tested at 38%) and Sodium Metabisulfite (undiluted) were not irritants to rabbits following occlusive exposures. Sodium Metabisulfite (tested at 50%) was irritating to guinea pigs following repeated exposure. In rats, Sodium Sulfite heptahydrate at large doses (up to 3.3 g/kg) produced fetal toxicity but not teratogenicity. Sodium Bisulfite, Sodium Metabisulfite, and Potassium Metabisulfite were not teratogenic for mice, rats, hamsters, or rabbits at doses up to 160 mg/kg. Generally, Sodium Sulfite, Sodium

  11. From menu to mouth: opportunities for sodium reduction in restaurants.

    Science.gov (United States)

    Levings, Jessica Lee; Gunn, Janelle Peralez

    2014-01-23

    Restaurant foods can be a substantial source of sodium in the American diet. According to the Institute of Medicine, the significant contribution made by restaurants and food service menu items to Americans' sodium intake warrants targeted attention. Public health practitioners are uniquely poised to support sodium-reduction efforts in restaurants and help drive demand for lower-sodium products through communication and collaboration with restaurant and food service professionals and through incentives for restaurants. This article discusses the role of the public health practitioner in restaurant sodium reduction and highlights select strategies that have been taken by state and local jurisdictions to support this effort.

  12. SODIUM LOSS INDUCED HYPONATREMIA IN THE ELDERLY ON A LOW SODIUM DIET

    Directory of Open Access Journals (Sweden)

    Juan F. Macías Núñez

    2006-04-01

    Full Text Available RESUMENLa hiponatremia es un desorden electrolítico que consiste en un aumento relativo a nivel corporal del contenido acuoso respecto del salino.La retención de agua libre o la pérdida de sodio son sus mecanismos causales principales, siendo el primero de ellos el más frecuente. Sin embargo, dado que los ancianos normales poseen un aumento en la excreción urinaria de sodio respecto de los jóvenes, pueden desarrollar hiponatremia secundaria a deplección salina cuando han estado en forma prolongada bajo una dieta hiposódica.En este reporte presentamos un caso de hiponatremia que fue resuelto mediante la restitución de sodio y no mediante la restricción hídrica. Analizamos también la baja confiabilidad de la excreción fraccional de urea en la interpretación de la etiología de la hiponatremia en los ancianos.BSTRACTHyponatremia is an electrolyte disorder which consist of a relative increase in body free water content respect to sodium one. Free water retention or sodium loss are its possible mechanisms, being the former more frequent than the latter. However, since urinary sodium loss is increased in healthy elderly, sodium depletion can be a frequent etiology of hyponatremia in this people when they have been on a low sodium diet for a long period.In this report a case of hyponatremia that solved with sodium restitution instead of water restriction is presented, and the name of senile sodium leakage hyponatremia is proposed for this entity. It is also analyzed the low reliability that fractional excretion of urea seems to have in the evaluation of this syndrome.

  13. [Sodium transport in chronic renal insufficiency].

    Science.gov (United States)

    Noé, D

    1985-03-24

    From an analysis of the literature covering the problem of sodium contribution in uraemic patients subjected to both conservative treatment and maintenance dialysis, it has been shown that excessive reduction in dietary sodium intake can be harmful unless it is justified by severe hypertension or oedema since it aggravates the state of uraemia. In these cases, the addition of a minimum controlled amount of hyposodic salt to an otherwise salt free diet is undoubtedly useful. The hyposodic salt, "Misura" manufactured by the company "Plasmon" was used in the dietary treatment of a series of patients subjected to mild restriction in dietary salt intake. Misura was well tolerated and well accepted thanks to its pleasing taste.

  14. Sodium fast reactor evaluation: Core materials

    Science.gov (United States)

    Cheon, Jin Sik; Lee, Chan Bock; Lee, Byoung Oon; Raison, J. P.; Mizuno, T.; Delage, F.; Carmack, J.

    2009-07-01

    In the framework of the Generation IV Sodium Fast Reactor (SFR) Program the Advanced Fuel Project has conducted an evaluation of the available fuel systems supporting future sodium cooled fast reactors. In this paper the status of available and developmental materials for SFR core cladding and duct applications is reviewed. To satisfy the Generation IV SFR fuel requirements, an advanced cladding needs to be developed. The candidate cladding materials are austenitic steels, ferritic/martensitic (F/M) steels, and oxide dispersion strengthened (ODS) steels. A large amount of irradiation testing is required, and the compatibility of cladding with TRU-loaded fuel at high temperatures and high burnup must be investigated. The more promising F/M steels (compared to HT9) might be able to meet the dose requirements of over 200 dpa for ducts in the GEN-IV SFR systems.

  15. Biotransformation of the pesticide sodium arsenate.

    Science.gov (United States)

    Shariatpanahi, M; Anderson, A C; Abdelghani, A A; Englande, A J; Hughes, J; Wilkinson, R F

    1981-01-01

    Biotransformation is an important parameter in assessing the environmental impact and fate of pesticides since metabolites produced may be either more or less toxic than the parent compound. Sodium arsenate (+5 inorganic), the wood preservative and insecticide, may be converted to both inorganic (+3) and organic compounds (-3) by microorganisms in soil, sediment and water bodies. Biotransformation of sodium arsenate was studied in pure cultures of 5 bacterial species using a mineral salt and limited carbon source medium. Arsenate concentrations were 10 microgram/ml and 100 microgram/ml of arsenic respectively. The rate of biodegradation of the parent compound was described by a first order composite exponential equation of the form Ct = C1e-k1t+C2e-k2t. Rates of production of metabolites (arsenite, monomethylarsine, dimethylarsine and trimethylarsine) were described by a first order exponential equation of the form Ct = Co (1-e-kt).

  16. Using Sodium Hydrogen Carbonate for Foaming Polymers

    Directory of Open Access Journals (Sweden)

    Satin Lukáš

    2016-09-01

    Full Text Available All plastics products are made of the essential polymer mixed with a complex blend of materials known collectively as additives. Without additives, plastics would not work, but with them, they can be made safer, cleaner, tougher and more colourful. Additives cost money, but by reducing production costs and making products live longer, they help us save money and conserve the world's precious raw material reserves. In fact, our world would be a lot less safe, a lot more expensive and a great deal duller without the additives that turn basic polymers into useful plastics. One of these additives is sodium bicarbonate. Influence of sodium bicarbonate on properties of the product made of polystyrene was observed in the research described in this paper. Since polystyrene is typically used as a material for electrical components, the mechanical properties of tensile strength and inflammability were measured as a priority. Inflammability parameters were measured using a cone calorimeter.

  17. Mechanism of action of sodium hypochlorite

    Directory of Open Access Journals (Sweden)

    Estrela Carlos

    2002-01-01

    Full Text Available The choice of an irrigating solution for use in infected root canals requires previous knowledge of the microorganisms responsible for the infectious process as well as the properties of different irrigating solutions. Complex internal anatomy, host defenses and microorganism virulence are important factors in the treatment of teeth with asymptomatic apical periodontitis. Irrigating solutions must have expressive antimicrobial action and tissue dissolution capacity. Sodium hypochlorite is the most used irrigating solution in endodontics, because its mechanism of action causes biosynthetic alterations in cellular metabolism and phospholipid destruction, formation of chloramines that interfere in cellular metabolism, oxidative action with irreversible enzymatic inactivation in bacteria, and lipid and fatty acid degradation. The aim of this work is to discuss the mechanism of action of sodium hypochlorite based on its antimicrobial and physico-chemical properties.

  18. Computer model for analyzing sodium cold traps

    Energy Technology Data Exchange (ETDEWEB)

    McPheeters, C C; Raue, D J

    1983-05-01

    A computer model was developed to simulate the processes that occur in sodium cold traps. The Model for Analyzing Sodium Cold Traps (MASCOT) simulates any desired configuration of mesh arrangements and dimensions and calculates pressure drops and flow distributions, temperature profiles, impurity concentration profiles, and impurity mass distributions. The calculated pressure drop as a function of impurity mass content determines the capacity of the cold trap. The accuracy of the model was checked by comparing calculated mass distributions with experimentally determined mass distributions from literature publications and with results from our own cold trap experiments. The comparisons were excellent in all cases. A parametric study was performed to determine which design variables are most important in maximizing cold trap capacity.

  19. Enabling room temperature sodium metal batteries

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Ruiguo; Mushra, Kuber; Li, Xiaolin; Qian, Jiangfeng; Engelhard, Mark H.; Bowden, Mark E.; Han, Kee Sung; Mueller, Karl T.; Henderson, Wesley A.; Zhang, Jiguang

    2016-12-01

    Rechargeable batteries based upon sodium (Na+) cations are at the core of many new battery chemistries beyond Li-ion batteries. Rather than using carbon or alloy-based anodes, the direct utilization of solid sodium metal as an anode would be highly advantageous, but its use has been highly problematic due to its high reactivity. In this work, however, it is demonstrated that, by tailoring the electrolyte formulation, solid Na metal can be electrochemically plated/stripped at ambient temperature with high efficiency (> 99%) on both copper and inexpensive aluminum current collectors thereby enabling a shift in focus to new battery chemical couples based upon Na metal operating at ambient temperature. These highly concentrated electrolytes has enabled stable cycling of Na metal batteries based on a Na metal anode and Na3V2(PO4)3 cathode at high rates with very high efficiency.

  20. Gamma heated subassembly for sodium boiling experiments

    Energy Technology Data Exchange (ETDEWEB)

    Artus, S.C.

    1975-01-01

    The design of a system to boil sodium in an LMFBR is examined. This design should be regarded as a first step in a series of boiling experiments. The reactor chosen for the design of the boiling apparatus is the Experimental Breeder Reactor-II (EBR-II), located at the National Reactor Testing Station in Idaho. Criteria broadly classified as design objectives and design requirements are discussed.

  1. Sputtering of sodium on the planet Mercury

    Science.gov (United States)

    Mcgrath, M. A.; Johnson, R. E.; Lanzerotti, L. J.

    1986-01-01

    It is shown here that ion sputtering cannot account for the observed neutral sodium vapor column density on Mercury, but that it is an important loss mechanism for Na. Photons are likely to be the dominant stimulus, both directly through photodesorption and indirectly through thermal desorption of absorbed Na. It is concluded that the atmosphere produced is characterized by the planet's surface temperature, with the ion-sputtered Na contributing to a lesser, but more extended, component of the atmosphere.

  2. SELECTIVE SODIUM REMOVAL FROM LITHIUM CHLORIDE ...

    African Journals Online (AJOL)

    Preferred Customer

    properties against alkaline cations due to their structure. .... Impurities contents in the feedstock brine. Component. LiCl. Na. Ca. Mg. SO4. 2- ... The pH was varied from 5.0 to 9.0 by careful addition of 0.01 M HCl or ... effect on the structure. ... with sodium ion in lithium chloride brine as follows. +. +. +. +. −= +. yLi. PO. Zr. La.

  3. 21 CFR 184.1754 - Sodium diacetate.

    Science.gov (United States)

    2010-04-01

    ... used in food at levels not to exceed current good manufacturing practice in accordance with § 184.1(b...) of this chapter; and 0.05 percent for snack foods as defined in § 170.3(n)(37) of this chapter and... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium diacetate. 184.1754 Section 184.1754 Food...

  4. 21 CFR 184.1721 - Sodium acetate.

    Science.gov (United States)

    2010-04-01

    .... (d) The ingredient is used in food at levels not to exceed current good manufacturing practice in... defined in § 170.3(n)(23) of this chapter and snack foods as defined in § 170.3(n)(37) of this chapter; 0... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium acetate. 184.1721 Section 184.1721 Food and...

  5. Sputtering of sodium on the planet Mercury

    Science.gov (United States)

    Mcgrath, M. A.; Johnson, R. E.; Lanzerotti, L. J.

    1986-01-01

    It is shown here that ion sputtering cannot account for the observed neutral sodium vapor column density on Mercury, but that it is an important loss mechanism for Na. Photons are likely to be the dominant stimulus, both directly through photodesorption and indirectly through thermal desorption of absorbed Na. It is concluded that the atmosphere produced is characterized by the planet's surface temperature, with the ion-sputtered Na contributing to a lesser, but more extended, component of the atmosphere.

  6. Interpretation of postmortem vitreous concentrations of sodium and chloride.

    Science.gov (United States)

    Zilg, B; Alkass, K; Berg, S; Druid, H

    2016-06-01

    Vitreous fluid can be used to analyze sodium and chloride levels in deceased persons, but it remains unclear to what extent such results can be used to diagnose antemortem sodium or chloride imbalances. In this study we present vitreous sodium and chloride levels from more than 3000 cases. We show that vitreous sodium and chloride levels both decrease with approximately 2.2mmol/L per day after death. Since potassium is a well-established marker for postmortem interval (PMI) and easily can be analyzed along with sodium and chloride, we have correlated sodium and chloride levels with the potassium levels and present postmortem reference ranges relative the potassium levels. We found that virtually all cases outside the reference range show signs of antemortem hypo- or hypernatremia. Vitreous sodium or chloride levels can be the only means to diagnose cases of water or salt intoxication, beer potomania or dehydration. We further show that postmortem vitreous sodium and chloride strongly correlate and in practice can be used interchangeably if analysis of one of the ions fails. It has been suggested that vitreous sodium and chloride levels can be used to diagnose drowning or to distinguish saltwater from freshwater drowning. Our results show that in cases of freshwater drowning, vitreous sodium levels are decreased, but that this mainly is an effect of postmortem diffusion between the eye and surrounding water rather than due to the drowning process, since the decrease in sodium levels correlates with immersion time.

  7. Molecular biology of insect sodium channels and pyrethroid resistance.

    Science.gov (United States)

    Dong, Ke; Du, Yuzhe; Rinkevich, Frank; Nomura, Yoshiko; Xu, Peng; Wang, Lingxin; Silver, Kristopher; Zhorov, Boris S

    2014-07-01

    Voltage-gated sodium channels are essential for the initiation and propagation of the action potential in neurons and other excitable cells. Because of their critical roles in electrical signaling, sodium channels are targets of a variety of naturally occurring and synthetic neurotoxins, including several classes of insecticides. This review is intended to provide an update on the molecular biology of insect sodium channels and the molecular mechanism of pyrethroid resistance. Although mammalian and insect sodium channels share fundamental topological and functional properties, most insect species carry only one sodium channel gene, compared to multiple sodium channel genes found in each mammalian species. Recent studies showed that two posttranscriptional mechanisms, alternative splicing and RNA editing, are involved in generating functional diversity of sodium channels in insects. More than 50 sodium channel mutations have been identified to be responsible for or associated with knockdown resistance (kdr) to pyrethroids in various arthropod pests and disease vectors. Elucidation of molecular mechanism of kdr led to the identification of dual receptor sites of pyrethroids on insect sodium channels. Many of the kdr mutations appear to be located within or close to the two receptor sites. The accumulating knowledge of insect sodium channels and their interactions with insecticides provides a foundation for understanding the neurophysiology of sodium channels in vivo and the development of new and safer insecticides for effective control of arthropod pests and human disease vectors.

  8. Molecular Biology of Insect Sodium Channels and Pyrethroid Resistance

    Science.gov (United States)

    Dong, Ke; Du, Yuzhe; Rinkevich, Frank; Nomura, Yoshiko; Xu, Peng; Wang, Lingxin; Silver, Kristopher; Zhorov, Boris S.

    2015-01-01

    Voltage-gated sodium channels are essential for the initiation and propagation of the action potential in neurons and other excitable cells. Because of their critical roles in electrical signaling, sodium channels are targets of a variety of naturally occurring and synthetic neurotoxins, including several classes of insecticides. This review is intended to provide an update on the molecular biology of insect sodium channels and the molecular mechanism of pyrethroid resistance. Although mammalian and insect sodium channels share fundamental topological and functional properties, most insect species carry only one sodium channel gene, compared to multiple sodium channel genes found in each mammalian species. Recent studies showed that two posttranscriptional mechanisms, alternative splicing and RNA editing, are involved in generating functional diversity of sodium channels in insects. More than 50 sodium channel mutations have been identified to be responsible for or associated with knockdown resistance (kdr) to pyrethroids in various arthropod pests and disease vectors. Elucidation of molecular mechanism of kdr led to the identification of dual receptor sites of pyrethroids on insect sodium channels. Most of the kdr mutations appear to be located within or close to the two receptor sites. The accumulating knowledge of insect sodium channels and their interactions with insecticides provides a foundation for understanding the neurophysiology of sodium channels in vivo and the development of new and safer insecticides for effective control of arthropod pests and human disease vectors. PMID:24704279

  9. Skin Sodium Concentration Correlates with Left Ventricular Hypertrophy in CKD.

    Science.gov (United States)

    Schneider, Markus P; Raff, Ulrike; Kopp, Christoph; Scheppach, Johannes B; Toncar, Sebastian; Wanner, Christoph; Schlieper, Georg; Saritas, Turgay; Floege, Jürgen; Schmid, Matthias; Birukov, Anna; Dahlmann, Anke; Linz, Peter; Janka, Rolf; Uder, Michael; Schmieder, Roland E; Titze, Jens M; Eckardt, Kai-Uwe

    2017-06-01

    The pathogenesis of left ventricular hypertrophy in patients with CKD is incompletely understood. Sodium intake, which is usually assessed by measuring urinary sodium excretion, has been inconsistently linked with left ventricular hypertrophy. However, tissues such as skin and muscle may store sodium. Using (23)sodium-magnetic resonance imaging, a technique recently developed for the assessment of tissue sodium content in humans, we determined skin sodium content at the level of the calf in 99 patients with mild to moderate CKD (42 women; median [range] age, 65 [23-78] years). We also assessed total body overhydration (bioimpedance spectroscopy), 24-hour BP, and left ventricular mass (cardiac magnetic resonance imaging). Skin sodium content, but not total body overhydration, correlated with systolic BP (r=0.33, P=0.002). Moreover, skin sodium content correlated more strongly than total body overhydration did with left ventricular mass (r=0.56, Pskin sodium content is a strong explanatory variable for left ventricular mass, unaffected by BP and total body overhydration. In conclusion, we found skin sodium content to be closely linked to left ventricular mass in patients with CKD. Interventions that reduce skin sodium content might improve cardiovascular outcomes in these patients. Copyright © 2017 by the American Society of Nephrology.

  10. Mercury's Seasonal Sodium Exosphere: MESSENGER Orbital Observations

    Science.gov (United States)

    Cassidy, Timothy A.; Merkel, Aimee W.; Burger, Matthew H.; Killen, Rosemary M.; McClintock, William E.; Vervack, Ronald J., Jr.; Sarantos, Menelaos

    2014-01-01

    The Mercury Atmospheric and Surface Composition Spectrometer (MASCS) Ultraviolet and Visible Spectrometer (UVVS) on the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft now orbiting Mercury provides the first close-up look at the planet's sodium exosphere. UVVS has observed the exosphere from orbit almost daily for over 10 Mercury years. In this paper we describe and analyze a subset of these data: altitude profiles taken above the low-latitude dayside and south pole. The observations show spatial and temporal variations, but there are no obvious year-to-year variations in most of the observations. We do not see the episodic variability reported by some ground-based observers. We used these altitude profiles to make estimates of sodium density and temperature. The bulk of the exosphere, at about 1200 K, is much warmer than Mercury's surface. This value is consistent with some ground-based measurements and suggests that photon-stimulated desorption is the primary ejection process. We also observe a tenuous energetic component but do not see evidence of the predicted thermalized (or partially thermalized) sodium near Mercury's surface temperature. Overall we do not see the variable mixture of temperatures predicted by most Monte Carlo models of the exosphere.

  11. Developmental programing of thirst and sodium appetite.

    Science.gov (United States)

    Mecawi, Andre S; Macchione, Ana F; Nuñez, Paula; Perillan, Carmen; Reis, Luis C; Vivas, Laura; Arguelles, Juan

    2015-04-01

    Thirst and sodium appetite are the sensations responsible for the motivated behaviors of water and salt intake, respectively, and both are essential responses for the maintenance of hydromineral homeostasis in animals. These sensations and their related behaviors develop very early in the postnatal period in animals. Many studies have demonstrated several pre- and postnatal stimuli that are responsible for the developmental programing of thirst and sodium appetite and, consequently, the pattern of water and salt intake in adulthood in need-free or need-induced conditions. The literature systematically reports the involvement of dietary changes, hydromineral and cardiovascular challenges, renin-angiotensin system and steroid hormone disturbances, and lifestyle in these developmental factors. Therefore, this review will address how pre- and postnatal challenges can program lifelong thirst and sodium appetite in animals and humans, as well as which neuroendocrine substrates are involved. In addition, the possible epigenetic molecular mechanisms responsible for the developmental programing of drinking behavior, the clinical implications of hydromineral disturbances during pre- and postnatal periods, and the developmental origins of adult hydromineral behavior will be discussed.

  12. Properties of enteric coated sodium valproate pellets.

    Science.gov (United States)

    Bruce, L Diane; Petereit, Hans-Ulrich; Beckert, Thomas; McGinity, James W

    2003-10-02

    The influence of subcoat application and micro-environmental pH on the dissolution properties of enteric coated sodium valproate pellets was investigated. The pellets were prepared by solution-layering or wet-mass extrusion-spheronization methods. In order to pass the USP enteric test, the solution-layered and wet-mass extruded pellets required 35 and 25% weight gain of Eudragit L 30D-55, respectively. The application of a subcoat of either Methocel-E5 (HPMC) or Opadry AMB to the pellets resulted in a delay in sodium valproate release in 0.1N HCl. Further delay in drug release was observed when citric acid was present in a HPMC subcoat or when added to the core pellet formulation. The amount of drug released from coated pellets was a function of the level of citric acid in the pellet core or subcoat and subsequent micro-environmental pH of the pellets. Citric acid exerted a plasticizing effect on the enteric polymer film and improved film formation and polymer coalescence. When greater than 10% (w/w) citric acid was present in the pellets, a decrease in drug content was observed due to the conversion of sodium valproate to the volatile compound, valproic acid. Pellets containing less than 10% (w/w) citric acid maintained potency during processing.

  13. How and when to prescribe sodium fluoride.

    Science.gov (United States)

    Shambaugh, G E

    1989-03-01

    Sodium fluoride has now been used for 24 years in an effort to slow down or arrest sensorineural hearing nerve deterioration in patients with stapedial otosclerosis or after stapedectomy, as well as in patients with pure cochlear otosclerosis. Extensive clinical experience in thousands of patients with this therapy has demonstrated its value in arresting previously progressive sensorineural hearing loss. For a long time there were those who objected to this therapy on the basis that it had not been adequately proven by double-blind, placebo-controlled studies. They have been answered by Bretlau's study in Denmark and Fisch's from Switzerland; both investigators confirmed on small groups the value of sodium fluoride by double-blind, placebo-controlled studies. Extensive research by Professor Petrovic of Strasbourg while at our tissue culture laboratory at Northwestern University demonstrated the action of sodium fluoride on bone. A nicely designed study with radioactive strontium by Linthicum, House, and Althaus demonstrated its value in promoting maturation of a spongiotic focus. Today there is no reason to hesitate in prescribing this useful, effective, and safe medication to promote maturation of otospongiotic lesions, and thus to slow down or to arrest progression in sensorineural hearing loss.

  14. Transient sodium current at subthreshold voltages: activation by EPSP waveforms.

    Science.gov (United States)

    Carter, Brett C; Giessel, Andrew J; Sabatini, Bernardo L; Bean, Bruce P

    2012-09-20

    Tetrodotoxin (TTX)-sensitive sodium channels carry large transient currents during action potentials and also "persistent" sodium current, a noninactivating TTX-sensitive current present at subthreshold voltages. We examined gating of subthreshold sodium current in dissociated cerebellar Purkinje neurons and hippocampal CA1 neurons, studied at 37°C with near-physiological ionic conditions. Unexpectedly, in both cell types small voltage steps at subthreshold voltages activated a substantial component of transient sodium current as well as persistent current. Subthreshold EPSP-like waveforms also activated a large component of transient sodium current, but IPSP-like waveforms engaged primarily persistent sodium current with only a small additional transient component. Activation of transient as well as persistent sodium current at subthreshold voltages produces amplification of EPSPs that is sensitive to the rate of depolarization and can help account for the dependence of spike threshold on depolarization rate, as previously observed in vivo.

  15. TREATMENT OF SODIUM DISORDERS AFTER SURGERY OF CRANIOPHARYNGIOMA

    Institute of Scientific and Technical Information of China (English)

    黄文宇; 石祥恩

    2000-01-01

    Objective. To study the treatment of the patients with blood sodium disorder after craniopharyngioma surgery. Method. The blood sodium in 44 patients with craniopharyngiomas was daily examined from operative to post-op erative days. Hypernatremia is defined as [Na] > 145 mmol/1, and hyponatremia as [Na] < 135 mmol/L. Results. Of the 44 patients, 36 developed sodium disorder. Among them, simple hyponatremia was 16 patients, simple hypernatremia was 9 patients, and alternative sodiu m disorder was 11 patients. Conclusion. The blood sodium disorder in patients with craniopharyngiomas after surgery appears to present com plicated changes. Three types of blood sodium disorder could be determined as simple hyponatremia, simple hyperna tremia, and alternative sodium disorder. Treatment of the sodium disorder in patients with craniopharyngiomas after surgery could be carried in accordance with the above three types.

  16. Red blood cell sodium transport in patients with cirrhosis

    DEFF Research Database (Denmark)

    Henriksen, Ulrik Lütken; Kiszka-Kanowitz, Marianne; Bendtsen, Flemming

    2016-01-01

    Patients with advanced cirrhosis have abnormal sodium homoeostasis. The study was undertaken to quantify the sodium transport across the plasma membrane of red blood cells (RBC) in patients with cirrhosis. RBC efflux and influx of sodium were studied in vitro with tracer (22) Na(+) according...... to linear kinetics in 24 patients with cirrhosis and 14 healthy controls. The sodium efflux was modified by ouabain (O), furosemide (F) and a combination of O and F (O + F). RBC sodium was significantly decreased (4·6 versus control 6·3 mmol l(-1) , Psodium (r = 0·57, P......sodium efflux was higher in patients with cirrhosis (+46%, Psodium buffers showed that the F-insensitive sodium efflux was twice as high in cirrhosis as in controls (P = 0...

  17. Reduction of sodium content in spicy soups using monosodium glutamate

    DEFF Research Database (Denmark)

    Jinap, Selamat; Hajeb, Parvaneh; Karim, Roslina

    2016-01-01

    Background: Excessive dietary sodium intake causes several diseases, such as hypertension, cardiovascular and renal disease, etc. Hence, reducing sodium intake has been highly recommended. In this study the effect of monosodium glutamate (MSG), as an umami substance, on saltiness and sodium...... reduction was investigated.Methods and Results: The trained panellists were presented with basic spicy soups (curry chicken and chili chicken) containing different amounts of sodium chloride (NaCl) (0-1.2%) and MSG (0-1.2%). They tasted the optimum concentrations of NaCl and MSG for the two spicy soups...... that with the addition of MSG, it is possible to reduce sodium intake without changing the overall acceptability of the spicy soup. A 32.5% reduction in sodium level is made feasible by adding 0.7% MSG to the spicy soups.Conclusions: This study suggests that low-sodium soups can be developed by the addition...

  18. Sodium Nitrite and Sodium Thiosulfate Are Effective Against Acute Cyanide Poisoning When Administered by Intramuscular Injection.

    Science.gov (United States)

    Bebarta, Vikhyat S; Brittain, Matthew; Chan, Adriano; Garrett, Norma; Yoon, David; Burney, Tanya; Mukai, David; Babin, Michael; Pilz, Renate B; Mahon, Sari B; Brenner, Matthew; Boss, Gerry R

    2017-06-01

    The 2 antidotes for acute cyanide poisoning in the United States must be administered by intravenous injection. In the out-of-hospital setting, intravenous injection is not practical, particularly for mass casualties, and intramuscular injection would be preferred. The purpose of this study is to determine whether sodium nitrite and sodium thiosulfate are effective cyanide antidotes when administered by intramuscular injection. We used a randomized, nonblinded, parallel-group study design in 3 mammalian models: cyanide gas inhalation in mice, with treatment postexposure; intravenous sodium cyanide infusion in rabbits, with severe hypotension as the trigger for treatment; and intravenous potassium cyanide infusion in pigs, with apnea as the trigger for treatment. The drugs were administered by intramuscular injection, and all 3 models were lethal in the absence of therapy. We found that sodium nitrite and sodium thiosulfate individually rescued 100% of the mice, and that the combination of the 2 drugs rescued 73% of the rabbits and 80% of the pigs. In all 3 species, survival in treated animals was significantly better than in control animals (log rank test, Pcyanide poisoning in 3 clinically relevant animal models of out-of-hospital emergency care. Copyright © 2016 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

  19. Spot urinary sodium for assessing dietary sodium restriction in cirrhotic ascites

    Institute of Scientific and Technical Information of China (English)

    Mohammed Abdelhamid El-Bokl; Bahaa Eldeen Senousy; Khaled Zakaria El-Karmouty; Inas El-Khedr Mohammed; Sherif Monier Mohammed; Sherif Sadek Shabana; Hassan Shalaby

    2009-01-01

    AIM: To evaluate the accuracy of spot urinary Na/K and Na/creatinine (Cr) ratios as an alternative to 24-h urinary sodium in monitoring dietary compliance in patients with liver cirrhosis and ascites treated with diuretics. METHODS: The study was carried on 40 patients with liver cirrhosis and ascites treated with diuretic therapy. Patients were divided into two groups according to 24-h urinary sodium. We measured spot urine Na/K ratio, Na/ Cr ratio and 24-h urinary sodium. Student's t test was used to compare the interval variables and χ2 test to compare the nominal variables between the two groups. Receiver operator characteristic curve was used to identify the best cutoff point for Na/K and Na/Cr ratio. RESULTS: The best cutoff point for Na/K ratio was 2.5 ( P < 0.001) and area under the curve (AUC) was 0.9, and for Na/Cr ratio, the best cutoff point was 35 ( P < 0.001) and AUC was 0.885. Na/K ratio showed higher sensitivity and accuracy compared to Na/Cr ratio (87.5% and 87% for Na/K ratio; 81% and 85% for Na/Cr ratio, respectively). CONCLUSION: Spot urine Na/K ratio has adequate accuracy for assessment of dietary sodium restriction compared with 24-h urinary sodium in patients with liver cirrhosis and ascites.

  20. Investigation on the sodium leak accident of Monju. Sodium leak test simulating the Monju leak

    Energy Technology Data Exchange (ETDEWEB)

    Shimoyama, Kazuhito; Nishimura, Masahiro; Miyahara, Shinya; Miyake, Osamu; Tanabe, Hiromi [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center; Usami, Masayuki

    1996-11-01

    Sodium fire experiments were carried out two times using the Sodium Fire Test Rig (SOFT-1) in the Power Reactor and Nuclear Fuel Development Corp (PNC) as a part of works to research the cause of the accident in secondary main cooling system of Monju. The purposes of these experiments are to confirm the leak rate and leakage form of sodium from damaged thermometer, to confirm the damage to the piping insulating structure around the thermometer and to the flexible tube, and to compare the temperature history of the signal from the thermometer between the experiments and Monju. In the experiments 56({+-}2)g/sec was obtained as the leak rate under the condition of ensuring the leakage pass in the simulated thermometer. This leak rate was corrected to 53g/sec to take account of manufacturing error of the thermometer between the experiment and Monju. In calculation of this leak rate, it is assumed that the annulus size of thermometer well tip is a nominal distance and pressure value to the leakage sodium is 1.65kg/cm{sup 2}G, which was the maximum one during the leakage of Monju. The behavior of signal from the simulated thermometer was very similar to that of the damaged thermometer in Monju and it was confirmed this temperature history could be sufficiently explained by moving of the temperature contact position of the thermocouple following the runoff of leakage sodium. (J.P.N.)

  1. Sodium-calcium exchanger and multiple sodium channel isoforms in intra-epidermal nerve terminals

    Directory of Open Access Journals (Sweden)

    Gasser Andreas

    2010-11-01

    Full Text Available Abstract Background Nociception requires transduction and impulse electrogenesis in nerve fibers which innervate the body surface, including the skin. However, the molecular substrates for transduction and action potential initiation in nociceptors are incompletely understood. In this study, we examined the expression and distribution of Na+/Ca2+ exchanger (NCX and voltage-gated sodium channel isoforms in intra-epidermal free nerve terminals. Results Small diameter DRG neurons exhibited robust NCX2, but not NCX1 or NCX3 immunolabeling, and virtually all PGP 9.5-positive intra-epidermal free nerve terminals displayed NCX2 immunoreactivity. Sodium channel NaV1.1 was not detectable in free nerve endings. In contrast, the majority of nerve terminals displayed detectable levels of expression of NaV1.6, NaV1.7, NaV1.8 and NaV1.9. Sodium channel immunoreactivity in the free nerve endings extended from the dermal boundary to the terminal tip. A similar pattern of NCX and sodium channel immunolabeling was observed in DRG neurons in vitro. Conclusions NCX2, as well as NaV1.6, NaV1.7, NaV1.8 and NaV1.9, are present in most intra-epidermal free nerve endings. The presence of NCX2, together with multiple sodium channel isoforms, in free nerve endings may have important functional implications.

  2. Transient Studies of a Sodium Sulfur Cell

    Science.gov (United States)

    Caprio, Sarah

    Modern grids will include input from fossil-fueled power generation facilities as well as renewable energy sources, and these are expected to work together actively. One major problem with this integrated power production is that most renewable energy sources are intermittent and variable, and thus introduce a very challenging situation with regard to grid stability and reliability. Also, fossil-fueled power generation facilities have load cycles based on expected usage. A non-reliable power source cannot feasibly be used to supply the grid with proper amounts of energy needed in peak times. A solution to this dilemma is power storage. The sodium-sulfur battery has high potential for electrical storage at the grid level due to its high energy density, low cost of the reactants, and high open-circuit voltage. However, the use of sodium-sulfur batteries at the grid level requires high current density operation that can cause cell deterioration, leading to lower sulfur utilization and lower energy efficiency. In addition, it can result in undesired thermal runaway leading to potentially hazardous situations. A rigorous, dynamic model of a sodium-sulfur battery can be used to study these phenomena, design the battery for optimal transient performance, and develop mitigation strategies. Most literature on sodium-sulfur batteries is concerned the dynamics of the sulfur electrode (a sodium-polysulfide melt). There is limited data in the open literature for dynamics of an entire cell. With this motivation, a first-principles dynamic model of a sodium-sulfur cell (with beta"-alumina electrolyte) has been developed. The state of discharge (SOD) of a sodium-sulfur cell significantly affects the heat generation rate, rates of electrochemical reactions, and internal resistance. To capture these phenomena correctly, a fully coupled thermal-electrochemical model has been developed. The thermal model considers heat generation due to Ohmic loss, Peltier heat, and heat due to the

  3. Transformation of Sodium Bicarbonate and CO2 into Sodium Formate over NiPd Nanoparticle Catalyst

    Directory of Open Access Journals (Sweden)

    Mengnan eWang

    2013-09-01

    Full Text Available The present research systematically investigated, for the first time, the transformation of sodium bicarbonate and CO2 into sodium formate over a series of Ni based metal nanoparticles (NPs. Ni NPs and eight NiM (M stands for a second metal NPs were prepared by a facile wet chemical process and then their catalytic performance were evaluated in sodium bicarbonate hydrogenation. Bimetallic NiPd NPs with a composition of 7:3 were found to be superior for this reaction, which are more active than both pure Ni and Pd NPs. Hot filtration experiment suggested the NPs to be the truly catalytic active species and kinetic analysis indicated the reaction mechanism to be different than most homogeneous catalysts. The enhanced activity of the bimetallic nanoparticles may be attributed to their smaller size and improved stability.

  4. Transformation of Sodium Bicarbonate and CO2 into Sodium Formate over NiPd Nanoparticle Catalyst

    Science.gov (United States)

    Wang, Mengnan; Zhang, Jiaguang; Yan, Ning

    2013-09-01

    The present research systematically investigated, for the first time, the transformation of sodium bicarbonate and CO2 into sodium formate over a series of Ni based metal nanoparticles (NPs). Ni NPs and eight NiM (M stands for a second metal) NPs were prepared by a facile wet chemical process and then their catalytic performance were evaluated in sodium bicarbonate hydrogenation. Bimetallic NiPd NPs with a composition of 7:3 were found to be superior for this reaction, which are more active than both pure Ni and Pd NPs. Hot filtration experiment suggested the NPs to be the truly catalytic active species and kinetic analysis indicated the reaction mechanism to be different than most homogeneous catalysts. The enhanced activity of the bimetallic nanoparticles may be attributed to their smaller size and improved stability.

  5. Theoretical assessment of particle generation from sodium pool fires

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, M., E-mail: monica.gmartin@ciemat.es [CIEMAT, Unit of Nuclear Safety Research, Av. Complutense, 40, 28040 Madrid (Spain); Herranz, L.E., E-mail: luisen.herranz@ciemat.es [CIEMAT, Unit of Nuclear Safety Research, Av. Complutense, 40, 28040 Madrid (Spain); Kissane, M.P., E-mail: Martin.KISSANE@oecd.org [Nuclear Safety Technology and Regulation Division, OECD Nuclear Energy Agency (NEA), 46 quai Alphonse Le Gallo, 92100 Boulogne-Billancourt (France)

    2016-12-15

    Highlights: • Development of particle generation model for sodium-oxides aerosol formation. • Development of partially validated numerical simulations to build up maps of saturation ratio. • Nucleation of supersaturated vapours as relevant source of aerosols over sodium pools. • Prediction of high concentrations of primary particles in the combustion zone. - Abstract: Potential sodium discharge in the containment during postulated Beyond Design Basis Accidents (BDBAs) in Sodium-cooled Fast Reactors (SFRs) would have major consequences for accident development in terms of energetics and source term. In the containment, sodium vaporization and subsequent oxidation would result in supersaturated oxide vapours that would undergo rapid nucleation creating toxic aerosols. Therefore, modelling this vapour nucleation is essential to proper source term assessment in SFRs. In the frame of the EU-JASMIN project, a particle generation model to calculate the particle generation rate and their primary size during an in-containment sodium pool fire has been developed. Based on a suite of individual models for sodium vaporization, oxygen natural circulation (3D modelling), sodium-oxygen chemical reactions, sodium-oxides-vapour nucleation and condensation, its consistency has been partially validated by comparing with available experimental data. As an outcome, large temperature and vapour concentration gradients set over the sodium pool have been found which result in large particle concentrations in the close vicinity of the pool.

  6. Sodium movements in perfused squid giant axons. Passive fluxes.

    Science.gov (United States)

    Rojas, E; Canessa-Fischer, M

    1968-08-01

    Sodium movements in internally perfused giant axons from the squid Dosidicus gigas were studied with varying internal sodium concentrations and with fluoride as the internal anion. It was found that as the internal concentration of sodium was increased from 2 to 200 mM the resting sodium efflux increased from 0.09 to 34.0 pmoles/cm(2)sec and the average resting sodium influx increased from 42.9 to 64.5 pmoles/cm(2)sec but this last change was not statistically significant. When perfusing with a mixture of 500 mM K glutamate and 100 mM Na glutamate the resting efflux was 10 +/- 3 pmoles/cm(2)sec and 41 +/- 10 pmoles/cm(2)sec for sodium influx. Increasing the internal sodium concentration also increased both the extra influx and the extra efflux of sodium due to impulse propagation. At any given internal sodium concentration the net extra influx was about 5 pmoles/cm(2)impulse. This finding supports the notion that the inward current generated in a propagated action potential can be completely accounted for by movements of sodium.

  7. PLASMA SODIUM AND NaCl-SENSITIVE HYPERTENSION

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Objective To test the following three hypotheses: ①plasma sodium concentration displays a 24-hour rhythm; ②the circadian rhyt hm of plasma sodium is disrupted in SHR fed a basal NaCl diet; ③high NaCl diet elevates plasma sodium concentration and may lead to an increase in mean arteria l pressure (MAP) of SHR. Methods After having been instrumen ted with arterial catheter at 9 weeks of age, all rats (Spontaneously Hypertensi ve Rat, SHR; Wistar-Kyoto Rat, WKY) experienced two experimental protocols, th e mean arterial pressure and heart rate were monitored and the blood samples als o been analysed for sodium contents. Results On basal NaCl diet, plasma sodium concentrations in SHR w ere significantly higher than those of WKY at almost every time point measured a nd the plasma sodium concentration and MAP rhythms were in nearly opposite phase s; on high NaCl diet, the MAP and plasma sodium rhythms were essentially opposit e in WKY. In SHR, the plasma sodium rhythm was inversely related to the MAP rhyt hm. Conclusion Plasma sodium displays a significant circadian rhythm in rats. The high NaCl diet disrupts the normal plasma sodium circadian rhythm only in SHR.

  8. PLASMA SODIUM AND NaCl-SENSITIVE HYPERTENSION

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Objective:To test the following three hypotheses:(1)plasma sodium concentration displays a 24-hour rhythm;(2)the circadian rhythm of plasma sodium is disrupted in SHR fed a basal NaCl diet;(3)high NaCl diet elevates lpasma sodium concentration and may lead to an increase in mean arterial pressure(MAP)of SHR.Methods:After having been instrumented with arterial catheter at 9 weeks of age,all rats(Spontaneously Hypertensive Rat,SHR; Wistar-Kyoto Rat,WKY) experienced two experimental protocols,the mean arterial pressure and heart rate were monitored and the blood samples also been analysed for sodium contents.Results:On basal NaCl diet,plasma sodium concentrations in SHR were significantly higher than those of WKY at almost every time point measured and the plasma sodium concentration and MAP rhythms were in nearly opposite phases;on high NaCl diet,the MAP and plasma sodium rhythms were essentially opposite in WKY,In SHR,the plasma sodium rhythm was inversely related to the MAP rhythm.Conclusion:Plasma sodium displays a significant ciradian rhythm in rats.The high NaCl diet disrupts the normal plasma sodium circadian rhythm only in SHR.

  9. NSAIDs in the Treatment of Adult Asthma: Sodium Cromoglycate and Nedocromil Sodium

    Directory of Open Access Journals (Sweden)

    Michel-Y Rouleau

    1995-01-01

    Full Text Available Among nonsteroidal anti-inflammatory drugs used in the treatment of adult asthma, sodium cromoglycate and nedocromil sodium are the most frequently prescribed. These medications have a similar efficacy profile in asthma although it has been suggested that nedocromil is more powerful than cromoglycate, particularly in its steroid sparing effects. Both drugs have been recommended as alternatives to steroids in the treatment of mild asthma. They are useful in the prevention of bronchospasm induced by exposure to allergens or to a variety of other stimuli. In comparison with theophylline or low dose inhaled steroids, cromoglycate and nedocromil have shown a similar antiasthmatic efficacy, although this is variable among patients.

  10. On the Effect of Sodium Chloride and Sodium Sulfate on Cold Denaturation.

    Directory of Open Access Journals (Sweden)

    Andrea Pica

    Full Text Available Both sodium chloride and sodium sulfate are able to stabilize yeast frataxin, causing an overall increase of its thermodynamic stability curve, with a decrease in the cold denaturation temperature and an increase in the hot denaturation one. The influence of low concentrations of these two salts on yeast frataxin stability can be assessed by the application of a theoretical model based on scaled particle theory. First developed to figure out the mechanism underlying cold denaturation in water, this model is able to predict the stabilization of globular proteins provided by these two salts. The densities of the salt solutions and their temperature dependence play a fundamental role.

  11. Factors contributing to the breakdown of sodium beta-alumina

    Energy Technology Data Exchange (ETDEWEB)

    Buechele, A.C.

    1982-05-01

    Clarification of the breakdown process occurring during charge transfer in sodium beta alumina solid electrolytes was derived from: (1) studying the effects of molten sodium contact at 350/sup 0/C on single crystal sodium beta alumina and polycrystalline sodium beta alumina; (2) determination of critical current density by monitoring acoustic emissions accompanying crack growth in sodium/sodium beta alumina/sodium cells subjected to linear current ramping at 1 mA cm/sup -2/ sec/sup -1/; (3) failure analysis conducted on cycled electrolytes, some from commercial sodium/sulfur cells, which had been subjected to up to 703 Ahr cm/sup -2/ of charge transfer. Gray coloration developing in beta aluminas in contact with molten sodium was found to be a consequence of formation, through reduction by sodium, of oxygen vacancies charge compensated by electrons. Electronic conductivity of the electrolyte increases as a result. No second phase formation was detected. Colored electrolytes from sodium/sulfur cells show evidence of a newly recognized degradation mechanism in which fracture occurs when sodium is reduced and deposited internally under pressure as metal in regions where an electronic conductivity gradient exists. Heating colored beta aluminas in air produces reoxidation and bleaching. Kinetics and other properties of the coloration and bleaching processes were determined. Critical current density was found to bear an inverse relation to average electrolyte grain size. Evidence was found in the cycled electrolytes for a slow crack growth mechanism and a progressive mode of degradation advancing from the sulfur electrode interface. Implications of the findings for the construction and operation of sodium/sulfur battery systems are discussed.

  12. 21 CFR 133.178 - Pasteurized neufchatel cheese spread with other foods.

    Science.gov (United States)

    2010-04-01

    ... karaya, gum tragacanth, carob bean gum, gelatin, algin (sodium alginate), propylene glycol alginate, guar gum, sodium carboxymethylcellulose (cellulose gum), carrageenan, oat gum, or xanthan gum. The total...)(1)(i) of this section are used, dioctyl sodium sulfosuccinate complying with the requirements of...

  13. Modeling and Validation of Sodium Plugging for Heat Exchangers in Sodium-cooled Fast Reactor Systems

    Energy Technology Data Exchange (ETDEWEB)

    Ferroni, Paolo [Westinghouse Electric Company LLC, Cranberry Township, PA (United States). Global Technology Development; Tatli, Emre [Westinghouse Electric Company LLC, Cranberry Township, PA (United States); Czerniak, Luke [Westinghouse Electric Company LLC, Cranberry Township, PA (United States); Sienicki, James J. [Argonne National Lab. (ANL), Argonne, IL (United States); Chien, Hual-Te [Argonne National Lab. (ANL), Argonne, IL (United States); Yoichi, Momozaki [Argonne National Lab. (ANL), Argonne, IL (United States); Bakhtiari, Sasan [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-06-29

    The project “Modeling and Validation of Sodium Plugging for Heat Exchangers in Sodium-cooled Fast Reactor Systems” was conducted jointly by Westinghouse Electric Company (Westinghouse) and Argonne National Laboratory (ANL), over the period October 1, 2013- March 31, 2016. The project’s motivation was the need to provide designers of Sodium Fast Reactors (SFRs) with a validated, state-of-the-art computational tool for the prediction of sodium oxide (Na2O) deposition in small-diameter sodium heat exchanger (HX) channels, such as those in the diffusion bonded HXs proposed for SFRs coupled with a supercritical CO2 (sCO2) Brayton cycle power conversion system. In SFRs, Na2O deposition can potentially occur following accidental air ingress in the intermediate heat transport system (IHTS) sodium and simultaneous failure of the IHTS sodium cold trap. In this scenario, oxygen can travel through the IHTS loop and reach the coldest regions, represented by the cold end of the sodium channels of the HXs, where Na2O precipitation may initiate and continue. In addition to deteriorating HX heat transfer and pressure drop performance, Na2O deposition can lead to channel plugging especially when the size of the sodium channels is small, which is the case for diffusion bonded HXs whose sodium channel hydraulic diameter is generally below 5 mm. Sodium oxide melts at a high temperature well above the sodium melting temperature such that removal of a solid plug such as through dissolution by pure sodium could take a lengthy time. The Sodium Plugging Phenomena Loop (SPPL) was developed at ANL, prior to this project, for investigating Na2O deposition phenomena within sodium channels that are prototypical of the diffusion bonded HX channels envisioned for SFR-sCO2 systems. In this project, a Computational Fluid Dynamic (CFD) model capable of simulating the thermal-hydraulics of the SPPL test

  14. Toxicology and pharmacology of sodium ricinoleate.

    Science.gov (United States)

    Burdock, George A; Carabin, Ioana G; Griffiths, James C

    2006-10-01

    Ricinoleic acid constitutes approximately 90% of the fatty acid content of castor oil. Castor oil is known for its purgative effects and can be used to induce labor. Both castor oil and ricinoleic acid are approved for use in food. The mechanistic basis for purgative actions likely includes the membrane-disruptive effects of detergent-like molecules, such as sodium ricinoleate (a 'soap'). These effects have been shown to be dose-related and to exhibit a threshold below which no laxative response was evident, in both animals and in humans. Castor oil was not toxic in subchronic feeding studies in rodents at doses ranging up to 10-20% of the diet. Sodium ricinoleate, as a surfactant, demonstrates predictable skin and mucus membrane irritant effects, and may induce a Type IV dermal sensitization response in those previously sensitized to it. However, food-grade castor oil and sodium ricinoleate are prepared in such a manner as to be free of the castor bean constituents that have been proven to be the source of reported Type I immediate hypersensitivity responses. Feeding studies with castor oil in rodents provide a basis for a no observable adverse effect level (NOAEL) estimate of 7,500 mg/kg/day and 5,000 mg/kg/day in mice and rats, respectively (). Applying an uncertainty factor of 100 to the lesser of these NOAELs, one can thus estimate an acceptable daily intake (ADI) in man to be 50 mg/kg, or 3,000 mg of castor oil per day in an average 60 kg person. As ricinoleic acid constitutes approximately 90% of castor oil, applying this calculation to the 3,000 mg/day estimated ADI in humans for castor oil (given the rapid hydrolysis of castor oil glyceride in the gastrointestinal tract), the acceptable daily intake of ricinoleic acid may be as high as 2,400 mg/person.

  15. Effects of low-sodium diet vs. high-sodium diet on blood pressure, renin, aldosterone, catecholamines, cholesterol, and triglyceride (Cochrane Review)

    DEFF Research Database (Denmark)

    Graudal, Niels A; Hubeck-Graudal, Thorbjørn; Jürgens, Gesche

    2012-01-01

    The question of whether reduced sodium intake is effective as a health prophylaxis initiative is unsolved. The purpose was to estimate the effects of low-sodium vs. high-sodium intake on blood pressure (BP), renin, aldosterone, catecholamines, and lipids.......The question of whether reduced sodium intake is effective as a health prophylaxis initiative is unsolved. The purpose was to estimate the effects of low-sodium vs. high-sodium intake on blood pressure (BP), renin, aldosterone, catecholamines, and lipids....

  16. Difference of Sodium Currents between Pediatric and Adult Human Atrial Myocytes: Evidence for Developmental Changes of Sodium Channels

    Directory of Open Access Journals (Sweden)

    Benzhi Cai, Xiaoqin Mu, Dongmei Gong, Shulin Jiang, Jianping Li, Qingxin Meng, Yunlong Bai, Yanju Liu, Xinyue Wang, Xueying Tan, Baofeng Yang, Yanjie Lu

    2011-01-01

    Full Text Available Voltage-gated calcium currents and potassium currents were shown to undergo developmental changes in postnatal human and animal cardiomocytes. However, so far, there is no evidence whether sodium currents also presented the developmental changes in postnatal human atrial cells. The aim of this study was to observe age-related changes of sodium currents between pediatric and adult atrial myocytes. Human atrial myocytes were acutely isolated and the whole-cell patch clamp technique was used to record sodium currents isolated from pediatric and adult atrial cardiomocytes. The peak amplitude of sodium currents recorded in adult atrial cells was significantly larger than that in pediatric atrial myocytes. However, there was no significant difference of the activation voltage for peak sodium currents between two kinds of atrial myocytes. The time constants for the activation and inactivation of sodium currents were smaller in adult atria than pediatric atria. The further study revealed that the voltage-dependent inactivation of sodium currents were more slow in adult atrial cardiomyocytes than pediatric atrial cells. A significant difference was also observed in the recovery process of sodium channel from inactivation. In summary, a few significant differences were demonstrated in sodium currents characteristics between pediatric and adult atrial myocytes, which indicates that sodium currents in human atria also undergo developmental changes.

  17. Characterization of Sodium Mobility and Binding by (23) Na NMR Spectroscopy in a Model Lipoproteic Emulsion Gel for Sodium Reduction.

    Science.gov (United States)

    Okada, Kyle S; Lee, Youngsoo

    2017-07-01

    The effects of formulation and processing parameters on sodium availability in a model lipid/protein-based emulsion gel were studied for purposes of sodium reduction. Heat-set model gels were prepared with varying levels of protein, lipid, and NaCl contents and high pressure homogenization treatments. Single quantum and double quantum-filtered (23) Na NMR spectroscopy experiments were used to characterize sodium mobility, structural order around "bound" (restricted mobility) sodium, and sodium binding, which have been correlated to saltiness perception in food systems previously. Total sodium mobility was lower in gels with higher protein or fat content, and was not affected by changes in homogenization pressure. The gels with increased protein, fat, or homogenization pressure had increased structure surrounding "bound" sodium and more relative "bound" sodium due to increased interfacial protein interactions. The data obtained in this study provide information on factors affecting sodium availability, which can be applied towards sodium reduction in lipid/protein-based foods. © 2017 Institute of Food Technologists®.

  18. Lidocaine block of cardiac sodium channels

    OpenAIRE

    Bean, BP; Cohen, CJ; Tsien, RW

    1983-01-01

    Lidocaine block of cardiac sodium channels was studied in voltage-clamped rabbit purkinje fibers at drug concentrations ranging from 1 mM down to effective antiarrhythmic doses (5-20 μM). Dose-response curves indicated that lidocaine blocks the channel by binding one-to-one, with a voltage-dependent K(d). The half-blocking concentration varied from more than 300 μM, at a negative holding potential where inactivation was completely removed, to approximately 10 μM, at a depolarized holding pote...

  19. [Color reactions for identification of sodium cromoglycate].

    Science.gov (United States)

    Görlitzer, K; Badia, G; Jones, P G

    2001-05-01

    Chromone-2-carboxylic acid (3) reacts with aminopyrazolone (2) in methanolic hydrochloric acid to yield the orange-red polymethine dye 4. Treating dimethyl cromoglicate (6) with compound 2 and perchloric acid leads to the tetraperchlorate 7 of the red azamerocyanine 8. The phenol 9, obtained from alkaline hydrolysis of sodium cromoglicate (1a), couples with diazotized sulfanilic acid to form the red azo dye 10. The chromone 6 condenses with 1,3-dimethylbarbituric acid (DMBA) in acetic anhydride/acetic acid to the red oxonole 12. Cromoglicinic acid (1b) reacts under these conditions to yield the yellow polymethine dye 14, whose structure is elucidated by X-ray analysis.

  20. Multiphysics Modelling of Sodium Sulfur Battery

    Science.gov (United States)

    Mason, Jerry Hunter

    Due to global climate change and the desire to decrease greenhouse gas emissions, large scale energy storage has become a critical issue. Renewable energy sources such as wind and solar will not be a viable energy source unless the storage problem is solved. One of the practical and cost effective solutions for this problem is sodium sulfur batteries. These batteries are comprised of liquid electrode materials suspended in porous media and operate at relatively high temperatures (>300°C). The sodium anode and the sulfur/sodium-polysulfide cathode are separated by a solid electrolyte made of beta-alumina or NASICON material. Due to the use of porous materials in the electrodes, capillary pressure and the combination of capillary action and gravity become important. Capillary pressure has a strong dependence on the wetting phase (liquid electrode material) saturation; therefore sharp concentration gradients can occur between the inert gas and the electrode liquid, especially within the cathode. These concentration gradients can have direct impacts on the electrodynamics of the battery as they may produce areas of high electrical potential variation, which can decrease efficiency and even cause failures. Then, thermal management also becomes vital since the electrochemistry and material properties are sensitive to temperature gradients. To investigate these phenomena in detail and to attempt to improve upon battery design a multi-dimensional, multi-phase code has been developed and validated in this study. Then a porous media flow model is implemented. Transport equations for charge, mass and heat are solved in a time marching fashion using finite volume method. Material properties are calculated and updated as a function of time. The porous media model is coupled with the continuity equation and a separate diffusion equation for the liquid sodium in the melt. The total mass transport model is coupled with charge transport via Faraday's law. Results show that

  1. Photoabsorption of small sodium and magnesium clusters

    DEFF Research Database (Denmark)

    Solov'yov, Ilia; Greiner, Walter

    2004-01-01

    We predict the strong enhancement in the photoabsorption of small Mg clusters in the region of 4-5 eV due to the resonant excitation of the plasmon oscillations of cluster electrons. The photoabsorption spectra for neutral Mg clusters consisting of up to N=11 atoms have been calculated using it a...... deformation is analysed. The reliability of the used calculation scheme has been proved by performing the test calculation for a number of sodium clusters and the comparison of the results obtained with the results of other methods and experiment....

  2. A hot topic: temperature sensitive sodium channelopathies.

    Science.gov (United States)

    Egri, Csilla; Ruben, Peter C

    2012-01-01

    Perturbations to body temperature affect almost all cellular processes and, within certain limits, results in minimal effects on overall physiology. Genetic mutations to ion channels, or channelopathies, can shift the fine homeostatic balance resulting in a decreased threshold to temperature induced disturbances. This review summarizes the functional consequences of currently identified voltage-gated sodium (NaV) channelopathies that lead to disorders with a temperature sensitive phenotype. A comprehensive knowledge of the relationships between genotype and environment is not only important for understanding the etiology of disease, but also for developing safe and effective treatment paradigms.

  3. Sodium N-chloro-2-methylbenzenesulfonamidate sesquihydrate

    Directory of Open Access Journals (Sweden)

    B. Thimme Gowda

    2009-06-01

    Full Text Available In the title salt, Na+·C7H7ClNO2S−·1.5H2O, one of the water molecules lies on a twofold axis. The sodium ion shows an O6 octahedral coordination defined by three water O atoms and three sulfonyl O atoms derived from three different anions. The S—N distance of 1.5898 (19 Å is consistent with an S=N double bond. The crystal structure is stabilized by N—H...O and O—H...Cl hydrogen bonds.

  4. Progress toward sodium reduction in the United States.

    Science.gov (United States)

    Levings, Jessica; Cogswell, Mary; Curtis, Christine J; Gunn, Janelle; Neiman, Andrea; Angell, Sonia Y

    2012-10-01

    The average adult in the United States of America consumes well above the recommended daily limit of sodium. Average sodium intake is about 3 463 mg/day, as compared to the 2010 dietary guidelines for Americans recommendation of sodium reduction policies and programs in the United States at the federal, state, and local levels; efforts to monitor the health impact of sodium reduction; ways to assess consumer knowledge, attitudes, and behavior; and how these activities depend on and inform global efforts to reduce sodium intake. Reducing excess sodium intake is a public health opportunity that can save lives and health care dollars in the United States and globally. Future efforts, including sharing successes achieved and barriers identified in the United States and globally, may quicken and enhance progress.

  5. Reproductive toxicity of sodium valproate in male rats

    Directory of Open Access Journals (Sweden)

    Bairy Laxminarayana

    2010-01-01

    Full Text Available Objectives: To assess the effects of sodium valproate on rat sperm morphology, sperm count, motility, and histopathological changes in testis. Materials and Methods: Male Wistar rats (12 week old were treated with sodium valpraote and sacrificed at the end of 2 nd , 4 th , 5 th , 7 th , 10 th and 15 th week after the last exposure to sodium valproate. Epididymal sperm count, sperm motility, sperm morphology, and histopathology of testes were analyzed. Results: Sperm count and sperm motility were decreased significantly by sodium valproate. The percentage of abnormal sperms increased in a dose-dependent manner. A histopathological study revealed that sodium valproate had caused sloughing of epithelial cells in testes. Conclusion: Sodium valproate causes reversible change in sperm motility, sperm count, morphology, and cytoarchitecture of testes.

  6. Imaging of sodium in the brain: a brief review.

    Science.gov (United States)

    Shah, N Jon; Worthoff, Wieland A; Langen, Karl-Josef

    2016-02-01

    Sodium-based MRI plays a vital role in the study of metabolism and can unveil valuable information about emerging and existing pathology--in particular in the human brain. Sodium is the second most abundant MR active nucleus in living tissue and, due to its quadrupolar nature, has magnetic properties not common to conventional proton MRI, which can reveal further insights, such as information on the compartmental distribution of intra- and extracellular sodium. Nevertheless, the use of sodium nuclei for imaging comes at the expense of a lower sensitivity and significantly reduced relaxation times, making in vivo sodium studies feasible only at high magnetic field strength and by the use of dedicated pulse sequences. Hybrid imaging combining sodium MRI and positron emission tomography (PET) simultaneously is a novel and promising approach to access information on dynamic metabolism with much increased, PET-derived specificity. Application of this new methodology is demonstrated herein using examples from tumour imaging.

  7. Dietary sodium and health: more than just blood pressure.

    Science.gov (United States)

    Farquhar, William B; Edwards, David G; Jurkovitz, Claudine T; Weintraub, William S

    2015-03-17

    Sodium is essential for cellular homeostasis and physiological function. Excess dietary sodium has been linked to elevations in blood pressure (BP). Salt sensitivity of BP varies widely, but certain subgroups tend to be more salt sensitive. The mechanisms underlying sodium-induced increases in BP are not completely understood but may involve alterations in renal function, fluid volume, fluid-regulatory hormones, the vasculature, cardiac function, and the autonomic nervous system. Recent pre-clinical and clinical data support that even in the absence of an increase in BP, excess dietary sodium can adversely affect target organs, including the blood vessels, heart, kidneys, and brain. In this review, the investigators review these issues and the epidemiological research relating dietary sodium to BP and cardiovascular health outcomes, addressing recent controversies. They also provide information and strategies for reducing dietary sodium.

  8. Isotonic and hypertonic sodium loading in supine humans

    DEFF Research Database (Denmark)

    Andersen, L J; Jensen, T U; Bestle, M H

    1999-01-01

    The hypothesis that hypertonic saline infusion induces a greater natriuresis than infusion of the same amount of sodium as isotonic saline was tested in 8 supine subjects on fixed sodium intake of 150 mmol NaCl day(-1). Sodium loads equivalent to the amount of sodium contained in 10% of measured...... extracellular volume were administered intravenously over 90 min either as isotonic saline or as hypertonic saline (850 mmol L(-1)). A third series without saline infusion served as time control. Experiments lasted 8 h. Water balance and sodium loads were maintained by replacing the excreted amounts every hour....... Plasma sodium concentrations only increased following hypertonic saline infusion (by 2.7 +/- 0.3 mmol L(-1)). Oncotic pressure decreased significantly more with isotonic saline (4.1 +/- 0.3 mmHg) than with hypertonic saline (3.2 +/- 0.2 mmHg), indicating that isotonic saline induced a stronger volumetric...

  9. CFD Modeling of Sodium-Oxide Deposition in Sodium-Cooled Fast Reactor Compact Heat Exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Tatli, Emre; Ferroni, Paolo; Mazzoccoli, Jason

    2015-09-02

    The possible use of compact heat exchangers (HXs) in sodium-cooled fast reactors (SFR) employing a Brayton cycle is promising due to their high power density and resulting small volume in comparison with conventional shell-and-tube HXs. However, the small diameter of their channels makes them more susceptible to plugging due to Na2O deposition during accident conditions. Although cold traps are designed to reduce oxygen impurity levels in the sodium coolant, their failure, in conjunction with accidental air ingress into the sodium boundary, could result in coolant oxygen levels that are above the saturation limit in the cooler parts of the HX channels. This can result in Na2O crystallization and the formation of solid deposits on cooled channel surfaces, limiting or even blocking coolant flow. The development of analysis tools capable of modeling the formation of these deposits in the presence of sodium flow will allow designers of SFRs to properly size the HX channels so that, in the scenario mentioned above, the reactor operator has sufficient time to detect and react to the affected HX. Until now, analytical methodologies to predict the formation of these deposits have been developed, but never implemented in a high-fidelity computational tool suited to modern reactor design techniques. This paper summarizes the challenges and the current status in the development of a Computational Fluid Dynamics (CFD) methodology to predict deposit formation, with particular emphasis on sensitivity studies on some parameters affecting deposition.

  10. Primate response to angiotensin infusion and high sodium intake differ by sodium lithium countertransport phenotype

    NARCIS (Netherlands)

    Spradling-Reeves, K.D.; Shade, R.E.; Haywood, J.R.; Cox, L.A.E.

    2017-01-01

    An increased level of sodium-lithium countertransport (SLC) activity has been associated with salt-sensitive hypertension. Previous findings have suggested that dysregulation of the renin-angiotensin-aldosterone system (RAAS) may be involved in the mechanism linking elevated SLC activity and hyperte

  11. Photodissociation of sodium iodide and resonant ionization of sodium atom produced

    Institute of Scientific and Technical Information of China (English)

    HUO Bing-hai; Z.T.Salim; A.H.Bakery

    2004-01-01

    Resonant ionization spectroscopy (RIS) and resonant ionization mass spectroscopy (RIMS) are employed to detect the photodissociation product of sodium iodide molecules in a molecular beam in an intense laser field in the absence of the buffer gases. Time of flight mass spectra is recorded. In particular, the appearances of multiphoton ionization are discussed.

  12. 49 CFR 173.189 - Batteries containing sodium or cells containing sodium.

    Science.gov (United States)

    2010-10-01

    ..., by aircraft. Batteries containing liquid sodium may be transported by motor vehicle, rail car or... preventing external short circuits, such as by providing complete electrical insulation of battery terminals or other external electrical connectors. Battery terminals or other electrical connectors penetrating...

  13. Canadian Initiatives to Prevent Hypertension by Reducing Dietary Sodium

    Directory of Open Access Journals (Sweden)

    Robert Strang

    2011-08-01

    Full Text Available Hypertension is the leading risk for premature death in the world. High dietary sodium is an important contributor to increased blood pressure and is strongly associated with other important diseases (e.g., gastric cancer, calcium containing kidney stones, osteoporosis, asthma and obesity. The average dietary sodium intake in Canada is approximately 3400 mg/day. It is estimated that 30% of hypertension, more than 10% of cardiovascular events and 1.4 billion dollars/year in health care expenses are caused by this high level of intake in Canada. Since 2006, Canada has had a focused and evolving effort to reduce dietary sodium based on actions from Non Governmental Organizations (NGO, and Federal and Provincial/Territorial Government actions. NGOs initiated Canadian sodium reduction programs by developing a policy statement outlining the health issue and calling for governmental, NGO and industry action, developing and disseminating an extensive health care professional education program including resources for patient education, developing a public awareness campaign through extensive media releases and publications in the lay press. The Federal Government responded by striking a Intersectoral Sodium Work Group to develop recommendations on how to implement Canada’s dietary reference intake values for dietary sodium and by developing timelines and targets for foods to be reduced in sodium, assessing key research gaps with funding for targeted dietary sodium based research, developing plans for public education and for conducting evaluation of the program to reduce dietary sodium. While food regulation is a Federal Government responsibility Provincial and Territorial governments indicated reducing dietary sodium needed to be a priority. Federal and Provincial Ministers of Health have endorsed a target to reduce the average consumption of sodium to 2300 mg/day by 2016 and the Deputy Ministers of Health have tasked a joint committee to review the

  14. Simultaneous modifications of sodium channel gating by two scorpion toxins.

    OpenAIRE

    1982-01-01

    The effects of purified scorpion toxins from two different species on the kinetics of sodium currents were evaluated in amphibian myelinated nerves under voltage clamp. A toxin from Leiurus quinquestriatus slowed and prevented sodium channel inactivation, exclusively, and a toxin from Centruroides sculpturatus Ewing reduced transient sodium currents during a maintained depolarization, and induced a novel inward current that appeared following repolarization, as previously reported by Cahalan ...

  15. Transperitoneal transport of sodium during hypertonic peritoneal dialysis

    DEFF Research Database (Denmark)

    Graff, J; Fugleberg, S; Brahm, J

    1996-01-01

    The mechanisms of transperitoneal sodium transport during hypertonic peritoneal dialysis were evaluated by kinetic modelling. A total of six nested mathematical models were designed to elucidate the presence or absence of diffusive, non-lymphatic convective and lymphatic convective solute transport....... Experimental results were obtained from 26 non-diabetic patients undergoing peritoneal dialysis. The model validation procedure demonstrated that only diffusive and non-lymphatic convective transport mechanisms were identifiable in the transperitoneal transport of sodium. Non-lymphatic convective sodium...

  16. Modelling Homogeneous Nucleation in Sodium Fast Reactors under BDBA Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, M.; Herranz, L. E.; Kissane, M.

    2014-07-01

    During postulated Beyond Design Basis Accidents (BDBAs) in Sodium-cooled Fast Reactors (SFRs), the contaminated coolant discharge at high temperature into the containment is considered as a potential scenario during the severe accident progression. In this scenario, the vaporization of sodium and its subsequent combustion (oxidation) would result in supersaturated sodium oxide vapours and formation of large quantities of contaminated aerosols by nucleation of these combustion products. (Author)

  17. Canadian initiatives to prevent hypertension by reducing dietary sodium.

    Science.gov (United States)

    Campbell, Norm R C; Willis, Kevin J; L'Abbe, Mary; Strang, Robert; Young, Eric

    2011-08-01

    Hypertension is the leading risk for premature death in the world. High dietary sodium is an important contributor to increased blood pressure and is strongly associated with other important diseases (e.g., gastric cancer, calcium containing kidney stones, osteoporosis, asthma and obesity). The average dietary sodium intake in Canada is approximately 3400 mg/day. It is estimated that 30% of hypertension, more than 10% of cardiovascular events and 1.4 billion dollars/year in health care expenses are caused by this high level of intake in Canada. Since 2006, Canada has had a focused and evolving effort to reduce dietary sodium based on actions from Non Governmental Organizations (NGO), and Federal and Provincial/Territorial Government actions. NGOs initiated Canadian sodium reduction programs by developing a policy statement outlining the health issue and calling for governmental, NGO and industry action, developing and disseminating an extensive health care professional education program including resources for patient education, developing a public awareness campaign through extensive media releases and publications in the lay press. The Federal Government responded by striking a Intersectoral Sodium Work Group to develop recommendations on how to implement Canada's dietary reference intake values for dietary sodium and by developing timelines and targets for foods to be reduced in sodium, assessing key research gaps with funding for targeted dietary sodium based research, developing plans for public education and for conducting evaluation of the program to reduce dietary sodium. While food regulation is a Federal Government responsibility Provincial and Territorial governments indicated reducing dietary sodium needed to be a priority. Federal and Provincial Ministers of Health have endorsed a target to reduce the average consumption of sodium to 2300 mg/day by 2016 and the Deputy Ministers of Health have tasked a joint committee to review the recommendations of

  18. A TRIAL OF SODIUM VALPROATE IN TARDIVE-DYSKINESIA

    OpenAIRE

    Chadda, R.; Kulhara, P.

    1986-01-01

    SUMMARY This study reports the results of an open trial of Sodium Valproate in tardive-dyskinesia. Fifteen patients identified having tardive dyskinesia by two psychiatrists independently were treated with Sodium Valproate in dosage of 1200 mg/day for 4 weeks. Assessments were made on abbreviated Dyskinesia Scale. There was statistically significant improvement after 2 and 4 weeks of treatment. Authors found Sodium Valproate quite effective in the management of tardive-dyskinesia.

  19. Sodium valproate induced increased frequency of micturition and enuresis.

    Science.gov (United States)

    Gosavi, Devesh D; Suman, Akanksha; Jain, Manish

    2013-01-01

    Sodium valproate is a commonly used antiepileptic drug (AED) for control of a broad range of seizures. Adverse drug reactions (ADR) due to sodium valproate range from sedation to nausea, vomiting, weight gain, idiosyncratic adverse effects like hepatotoxicity and life threatening conditions like pancreatitis. We present a case of sodium valproate induced enuresis in child. This ADR of valproate is an underreported ADR and requires special attention of pediatricians as it can interfere with the further treatment of the disease.

  20. Determination of solubility of uranium in liquid sodium

    Institute of Scientific and Technical Information of China (English)

    YANG Tongzai; XING Pifeng; YE Shiyou; LONG Kaiming; FU Zhonghua; HE Yuhui; JIANG Tao

    2008-01-01

    An experimental technique has been developed which overcomes the two major problems common to liquid metal solubility measurements, namely, maintaining the integrity of the samples during transfer of the liquid sodium from container to whatever device is used for analysis and detecting solute at very low concentration in liquid sodium. The solubility of uranium in liquid sodium has been measured over the temperature range 150~400℃, by equilibration and sampling technique, the solubility of uranium is approximately 0.00001%.

  1. A TRIAL OF SODIUM VALPROATE IN TARDIVE-DYSKINESIA

    OpenAIRE

    Chadda, R.; Kulhara, P.

    1986-01-01

    SUMMARY This study reports the results of an open trial of Sodium Valproate in tardive-dyskinesia. Fifteen patients identified having tardive dyskinesia by two psychiatrists independently were treated with Sodium Valproate in dosage of 1200 mg/day for 4 weeks. Assessments were made on abbreviated Dyskinesia Scale. There was statistically significant improvement after 2 and 4 weeks of treatment. Authors found Sodium Valproate quite effective in the management of tardive-dyskinesia.

  2. Gastrointestinal osmoreceptors and renal sodium excretion in humans

    DEFF Research Database (Denmark)

    Andersen, L J; Skram, Thomas Ulrik; Bestle, M H;

    2000-01-01

    The hypothesis that natriuresis can be induced by stimulation of gastrointestinal osmoreceptors was tested in eight supine subjects on constant sodium intake (150 mmol NaCl/day). A sodium load equivalent to the amount contained in 10% of measured extracellular volume was administered by a nasogas......The hypothesis that natriuresis can be induced by stimulation of gastrointestinal osmoreceptors was tested in eight supine subjects on constant sodium intake (150 mmol NaCl/day). A sodium load equivalent to the amount contained in 10% of measured extracellular volume was administered......-angiotensin system....

  3. CDC grand rounds: dietary sodium reduction - time for choice.

    Science.gov (United States)

    2012-02-10

    Excess dietary sodium is a major contributor to hypertension (high blood pressure) and a critical public health issue in the United States. Nearly one in three U.S. adults, or 68 million persons, has hypertension, and half of those do not have their condition under control. Hypertension is a major contributor to cardiovascular diseases, which are a leading cause of death, disability, and health-care costs in the United States. The average sodium intake among persons in the United States aged ≥2 years is 3,266 mg/day (excluding table salt). Current dietary guidelines recommend that reducing consumption of sodium to sodium intake by most U.S. residents considerably exceeds recommended levels. Reducing sodium intake to 2,300 mg/day potentially could prevent 11 million cases of hypertension and save billions of dollars in health-care expenditures; reducing sodium intake further would yield additional benefits. To achieve those reductions and help consumers make healthful choices, expanded educational efforts and monitoring of the sodium content of the food supply are needed. Increased availability of lower sodium products and reductions in the amount of sodium in foods served or sold in the marketplace also are needed.

  4. Decaying wood is a sodium source for mountain gorillas.

    Science.gov (United States)

    Rothman, Jessica M; Van Soest, Peter J; Pell, Alice N

    2006-09-22

    Like several other non-human primates, mountain gorillas (Gorilla beringei beringei) in Bwindi Impenetrable National Park, Uganda consume decaying wood, an interesting but puzzling behaviour. This wood has little obvious nutritional value; it is low in protein and sugar, and high in lignin compared to other foods. We collected pieces of wood eaten and avoided by gorillas, and other foods consumed by gorillas, and measured their sodium content. Wood was substantially higher in sodium than other dietary items, and wood pieces from stumps eaten contained more sodium than those that were avoided. Wood represented only 3.9% of the wet weight food intake of gorillas, but contributed over 95% of dietary sodium, leading us to conclude that decaying wood is an important sodium source for Bwindi gorillas. Because sodium has been leached from the weathered soils characteristic of the subhumid and humid tropics, and because terrestrial plants generally do not require sodium, tropical herbivores, including gorillas, often encounter problems locating the sodium essential for their well-being. Decaying wood is an unexpected sodium source.

  5. Strategies to reduce sodium consumption: a food industry perspective.

    Science.gov (United States)

    Dötsch, Mariska; Busch, Johanneke; Batenburg, Max; Liem, Gie; Tareilus, Erwin; Mueller, Rudi; Meijer, Gert

    2009-11-01

    The global high prevalence of hypertension and cardiovascular disease has raised concerns regarding the sodium content of the foods which we consume. Over 75% of sodium intake in industrialized diets is likely to come from processed and restaurant foods. Therefore international authorities, such as the World Health Organisation, are encouraging the food industry to reduce sodium levels in their products. Significant sodium reduction is not without complications as salt plays an important role in taste, and in some products is needed also for preservation and processing. The most promising sodium reduction strategy is to adapt the preference of consumers for saltiness by reducing sodium in products in small steps. However, this is a time-consuming approach that needs to be applied industry-wide in order to be effective. Therefore the food industry is also investigating solutions that will maintain the same perceived salt intensity at lower sodium levels. Each of these has specific advantages, disadvantages, and time lines for implementation. Currently applied approaches are resulting in sodium reduction between 20-30%. Further reduction will require new technologies. Research into the physiology of taste perception and salt receptors is an emerging area of science that is needed in order to achieve larger sodium reductions.

  6. Lessons Learned From Community-Based Approaches to Sodium Reduction

    Science.gov (United States)

    Kane, Heather; Strazza, Karen; Losby PhD, Jan L.; Lane, Rashon; Mugavero, Kristy; Anater, Andrea S.; Frost, Corey; Margolis, Marjorie; Hersey, James

    2017-01-01

    Purpose This article describes lessons from a Centers for Disease Control and Prevention initiative encompassing sodium reduction interventions in six communities. Design A multiple case study design was used. Setting This evaluation examined data from programs implemented in six communities located in New York (Broome County, Schenectady County, and New York City); California (Los Angeles County and Shasta County); and Kansas (Shawnee County). Subjects Participants (n = 80) included program staff, program directors, state-level staff, and partners. Measures Measures for this evaluation included challenges, facilitators, and lessons learned from implementing sodium reduction strategies. Analysis The project team conducted a document review of program materials and semi structured interviews 12 to 14 months after implementation. The team coded and analyzed data deductively and inductively. Results Five lessons for implementing community-based sodium reduction approaches emerged: (1) build relationships with partners to understand their concerns, (2) involve individuals knowledgeable about specific venues early, (3) incorporate sodium reduction efforts and messaging into broader nutrition efforts, (4) design the program to reduce sodium gradually to take into account consumer preferences and taste transitions, and (5) identify ways to address the cost of lower-sodium products. Conclusion The experiences of the six communities may assist practitioners in planning community-based sodium reduction interventions. Addressing sodium reduction using a community-based approach can foster meaningful change in dietary sodium consumption. PMID:24575726

  7. Sodium fast reactor safety and licensing research plan. Volume II.

    Energy Technology Data Exchange (ETDEWEB)

    Ludewig, H. (Brokhaven National Laboratory, Upton, NY); Powers, D. A.; Hewson, John C.; LaChance, Jeffrey L.; Wright, A. (Argonne National Laboratory, Argonne, IL); Phillips, J.; Zeyen, R. (Institute for Energy Petten, Saint-Paul-lez-Durance, France); Clement, B. (IRSN/DPAM.SEMIC Bt 702, Saint-Paul-lez-Durance, France); Garner, Frank (Radiation Effects Consulting, Richland, WA); Walters, Leon (Advanced Reactor Concepts, Los Alamos, NM); Wright, Steve; Ott, Larry J. (Oak Ridge National Laboratory, Oak Ridge, TN); Suo-Anttila, Ahti Jorma; Denning, Richard (Ohio State University, Columbus, OH); Ohshima, Hiroyuki (Japan Atomic Energy Agency, Ibaraki, Japan); Ohno, S. (Japan Atomic Energy Agency, Ibaraki, Japan); Miyhara, S. (Japan Atomic Energy Agency, Ibaraki, Japan); Yacout, Abdellatif (Argonne National Laboratory, Argonne, IL); Farmer, M. (Argonne National Laboratory, Argonne, IL); Wade, D. (Argonne National Laboratory, Argonne, IL); Grandy, C. (Argonne National Laboratory, Argonne, IL); Schmidt, R.; Cahalen, J. (Argonne National Laboratory, Argonne, IL); Olivier, Tara Jean; Budnitz, R. (Lawrence Berkeley National Laboratory, Berkeley, CA); Tobita, Yoshiharu (Japan Atomic Energy Agency, Ibaraki, Japan); Serre, Frederic (Centre d' %C3%94etudes nucl%C3%94eaires de Cadarache, Cea, France); Natesan, Ken (Argonne National Laboratory, Argonne, IL); Carbajo, Juan J. (Oak Ridge National Laboratory, Oak Ridge, TN); Jeong, Hae-Yong (Korea Atomic Energy Research Institute, Daejeon, Korea); Wigeland, Roald (Idaho National Laboratory, Idaho Falls, ID); Corradini, Michael (University of Wisconsin-Madison, Madison, WI); Thomas, Justin (Argonne National Laboratory, Argonne, IL); Wei, Tom (Argonne National Laboratory, Argonne, IL); Sofu, Tanju (Argonne National Laboratory, Argonne, IL); Flanagan, George F. (Oak Ridge National Laboratory, Oak Ridge, TN); Bari, R. (Brokhaven National Laboratory, Upton, NY); Porter D. (Idaho National Laboratory, Idaho Falls, ID); Lambert, J. (Argonne National Laboratory, Argonne, IL); Hayes, S. (Idaho National Laboratory, Idaho Falls, ID); Sackett, J. (Idaho National Laboratory, Idaho Falls, ID); Denman, Matthew R.

    2012-05-01

    Expert panels comprised of subject matter experts identified at the U.S. National Laboratories (SNL, ANL, INL, ORNL, LBL, and BNL), universities (University of Wisconsin and Ohio State University), international agencies (IRSN, CEA, JAEA, KAERI, and JRC-IE) and private consultation companies (Radiation Effects Consulting) were assembled to perform a gap analysis for sodium fast reactor licensing. Expert-opinion elicitation was performed to qualitatively assess the current state of sodium fast reactor technologies. Five independent gap analyses were performed resulting in the following topical reports: (1) Accident Initiators and Sequences (i.e., Initiators/Sequences Technology Gap Analysis), (2) Sodium Technology Phenomena (i.e., Advanced Burner Reactor Sodium Technology Gap Analysis), (3) Fuels and Materials (i.e., Sodium Fast Reactor Fuels and Materials: Research Needs), (4) Source Term Characterization (i.e., Advanced Sodium Fast Reactor Accident Source Terms: Research Needs), and (5) Computer Codes and Models (i.e., Sodium Fast Reactor Gaps Analysis of Computer Codes and Models for Accident Analysis and Reactor Safety). Volume II of the Sodium Research Plan consolidates the five gap analysis reports produced by each expert panel, wherein the importance of the identified phenomena and necessities of further experimental research and code development were addressed. The findings from these five reports comprised the basis for the analysis in Sodium Fast Reactor Research Plan Volume I.

  8. Phenomenological studies on sodium for CSP applications: A safety review

    Science.gov (United States)

    Armijo, Kenneth M.; Andraka, Charles E.

    2016-05-01

    Sodium Heat transfer fluids (HTF) such as sodium, can achieve temperatures above 700°C to obtain power cycle performance improvements for reducing large infrastructure costs of high-temperature systems. Current concentrating solar power (CSP) sensible HTF's (e.g. air, salts) have poor thermal conductivity, and thus low heat transfer capabilities, requiring a large receiver. The high thermal conductivity of sodium has demonstrated high heat transfer rates on dish and towers systems, which allow a reduction in receiver area by a factor of two to four, reducing re-radiation and convection losses and cost by a similar factor. Sodium produces saturated vapor at pressures suitable for transport starting at 600°C and reaches one atmosphere at 870°C, providing a wide range of suitable operating conditions that match proposed high temperature, isothermal power cycles. This advantage could increase the efficiency while lowering the cost of CSP tower systems. Although there are a number of desirable thermal performance advantages associated with sensible sodium, its propensity to rapidly oxidize presents safety challenges. This investigation presents a literature review that captures historical operations/handling lessons for advanced sodium receiver designs, and the current state-of-knowledge related to sodium combustion behavior. Technical and operational solutions addressing sodium safety and applications in CSP will be discussed, including unique safety hazards and advantages using latent sodium. Lessons obtained from the nuclear industry with sensible and latent systems will also be discussed in the context of safety challenges and risk mitigation solutions.

  9. Excitability constraints on voltage-gated sodium channels.

    Directory of Open Access Journals (Sweden)

    Elaine Angelino

    2007-09-01

    Full Text Available We study how functional constraints bound and shape evolution through an analysis of mammalian voltage-gated sodium channels. The primary function of sodium channels is to allow the propagation of action potentials. Since Hodgkin and Huxley, mathematical models have suggested that sodium channel properties need to be tightly constrained for an action potential to propagate. There are nine mammalian genes encoding voltage-gated sodium channels, many of which are more than approximately 90% identical by sequence. This sequence similarity presumably corresponds to similarity of function, consistent with the idea that these properties must be tightly constrained. However, the multiplicity of genes encoding sodium channels raises the question: why are there so many? We demonstrate that the simplest theoretical constraints bounding sodium channel diversity--the requirements of membrane excitability and the uniqueness of the resting potential--act directly on constraining sodium channel properties. We compare the predicted constraints with functional data on mammalian sodium channel properties collected from the literature, including 172 different sets of measurements from 40 publications, wild-type and mutant, under a variety of conditions. The data from all channel types, including mutants, obeys the excitability constraint; on the other hand, channels expressed in muscle tend to obey the constraint of a unique resting potential, while channels expressed in neuronal tissue do not. The excitability properties alone distinguish the nine sodium channels into four different groups that are consistent with phylogenetic analysis. Our calculations suggest interpretations for the functional differences between these groups.

  10. An experiment on multibubble sonoluminescence spectra in sodium chloride solution

    Institute of Scientific and Technical Information of China (English)

    CHEN Zhan; XU JunFeng; HUANG Wei; CHEN WeiZhong; MIAO GuoQing

    2008-01-01

    We investigated experimentally the spectra of MBSL in sodium chloride water solution with krypton as dissolved gas. We observed and compared the spectra of hydroxyl ion at 310 nm and that of sodium atom at 589 nm. It has been found that under the same experimental condition, the intensity of sodium atom spectra is obviously higher than that of the hydroxyl ion spectra, and is more sensitive to the experimental condition. The krypton content, the concentration of sodium chloride solution, and the driving sound pressure obviously affect the spectra intensity in certain range.

  11. DDESC: Dragon database for exploration of sodium channels in human

    Directory of Open Access Journals (Sweden)

    Radovanovic Aleksandar

    2008-12-01

    Full Text Available Abstract Background Sodium channels are heteromultimeric, integral membrane proteins that belong to a superfamily of ion channels. The mutations in genes encoding for sodium channel proteins have been linked with several inherited genetic disorders such as febrile epilepsy, Brugada syndrome, ventricular fibrillation, long QT syndrome, or channelopathy associated insensitivity to pain. In spite of these significant effects that sodium channel proteins/genes could have on human health, there is no publicly available resource focused on sodium channels that would support exploration of the sodium channel related information. Results We report here Dragon Database for Exploration of Sodium Channels in Human (DDESC, which provides comprehensive information related to sodium channels regarding different entities, such as "genes and proteins", "metabolites and enzymes", "toxins", "chemicals with pharmacological effects", "disease concepts", "human anatomy", "pathways and pathway reactions" and their potential links. DDESC is compiled based on text- and data-mining. It allows users to explore potential associations between different entities related to sodium channels in human, as well as to automatically generate novel hypotheses. Conclusion DDESC is first publicly available resource where the information related to sodium channels in human can be explored at different levels. This database is freely accessible for academic and non-profit users via the worldwide web http://apps.sanbi.ac.za/ddesc.

  12. Sodium adduct formation efficiency in ESI source.

    Science.gov (United States)

    Kruve, Anneli; Kaupmees, Karl; Liigand, Jaanus; Oss, Merit; Leito, Ivo

    2013-06-01

    Formation of sodium adducts in electrospray (ESI) has been known for long time, but has not been used extensively in practice, and several important aspects of Na(+) adduct formation in ESI source have been almost unexplored: the ionization efficiency of different molecules via Na(+) adduct formation, its dependence on molecular structure and Na(+) ion concentration in solution, fragmentation behaviour of the adducts as well as the ruggedness (a prerequisite for wider practical use) of ionization via Na(+) adduct formation. In this work, we have developed a parameter describing sodium adducts formation efficiency (SAFE) of neutral molecules and have built a SAFE scale that ranges for over four orders of magnitude and contains 19 compounds. In general, oxygen bases have higher efficiency of Na(+) adducts formation than nitrogen bases because of the higher partial negative charge on oxygen atoms and competition from protonation in the case of nitrogen bases. Chelating ability strongly increases the Na(+) adduct formation efficiency. We show that not only protonation but also Na(+) adduct formation is a quantitative and reproducible process if relative measurements are performed.

  13. Nanostructures of sodium titanate/zirconium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Carolina M., E-mail: carolina@iqm.unicamp.br; Ferreira, Odair P., E-mail: opferreira@gmail.com; Alves, Oswaldo L., E-mail: oalves@iqm.unicamp.b [Instituto de Quimica, Universidade Estadual de Campinas (UNICAMP), Laboratorio de Quimica do Estado Solido (LQES) (Brazil)

    2010-09-15

    In this work is reported the synthesis of nanotubes and nanoribbons from mixed oxides (Ti{sub 1-x}Zr{sub x}O{sub 2}.nH{sub 2}O), employing hydrothermal treatment in a highly alkaline medium. The morphology and crystal structure of the products obtained via hydrothermal treatment depend on the value of x. For example, for x equal to 0 and 0.50 were observed the presence of nanotubes (diameter around 9 nm) and nanoribbons (diameter around 200 nm), respectively. However, for x values above 0.50, there was no morphological change. Regarding the crystalline structure of these samples, for x equal to 0 was observed the sodium titanate phase; already for x values up to 0.50, we observed the presence of two crystalline phases: sodium titanate and tetragonal ZrO{sub 2}. For x values above 0.50, only tetragonal ZrO{sub 2} was observed. Furthermore, only the product obtained from x equal to 0.15 was observed the presence of three-dimensional flower-like arrangements. The results obtained by the characterization techniques showed the segregation of zirconium after hydrothermal treatment of precursors with x less or equal to 0.50. Thus, we describe the important role that Ti/Zr molar ratio of the precursor plays on the morphology and crystalline phase of the products formed by hydrothermal treatment.

  14. Sodium Reactor Experiment decommissioning. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Carroll, J.W.; Conners, C.C.; Harris, J.M.; Marzec, J.M.; Ureda, B.F.

    1983-08-15

    The Sodium Reactor Experiment (SRE) located at the Rockwell International Field Laboratories northwest of Los Angeles was developed to demonstrate a sodium-cooled, graphite-moderated reactor for civilian use. The reactor reached full power in May 1958 and provided 37 GWh to the Southern California Edison Company grid before it was shut down in 1967. Decommissioning of the SRE began in 1974 with the objective of removing all significant radioactivity from the site and releasing the facility for unrestricted use. Planning documentation was prepared to describe in detail the equipment and techniques development and the decommissioning work scope. A plasma-arc manipulator was developed for remotely dissecting the highly radioactive reactor vessels. Other important developments included techniques for using explosives to cut reactor vessel internal piping, clamps, and brackets; decontaminating porous concrete surfaces; and disposing of massive equipment and structures. The documentation defined the decommissioning in an SRE dismantling plan, in activity requirements for elements of the decommissioning work scope, and in detailed procedures for each major task.

  15. Chloride binding site of neurotransmitter sodium symporters.

    Science.gov (United States)

    Kantcheva, Adriana K; Quick, Matthias; Shi, Lei; Winther, Anne-Marie Lund; Stolzenberg, Sebastian; Weinstein, Harel; Javitch, Jonathan A; Nissen, Poul

    2013-05-21

    Neurotransmitter:sodium symporters (NSSs) play a critical role in signaling by reuptake of neurotransmitters. Eukaryotic NSSs are chloride-dependent, whereas prokaryotic NSS homologs like LeuT are chloride-independent but contain an acidic residue (Glu290 in LeuT) at a site where eukaryotic NSSs have a serine. The LeuT-E290S mutant displays chloride-dependent activity. We show that, in LeuT-E290S cocrystallized with bromide or chloride, the anion is coordinated by side chain hydroxyls from Tyr47, Ser290, and Thr254 and the side chain amide of Gln250. The bound anion and the nearby sodium ion in the Na1 site organize a connection between their coordinating residues and the extracellular gate of LeuT through a continuous H-bond network. The specific insights from the structures, combined with results from substrate binding studies and molecular dynamics simulations, reveal an anion-dependent occlusion mechanism for NSS and shed light on the functional role of chloride binding.

  16. Cast Stone Formulation At Higher Sodium Concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Fox, K. M.; Edwards, T. A.; Roberts, K. B.

    2013-10-02

    A low temperature waste form known as Cast Stone is being considered to provide supplemental Low Activity Waste (LAW) immobilization capacity for the Hanford site. Formulation of Cast Stone at high sodium concentrations is of interest since a significant reduction in the necessary volume of Cast Stone and subsequent disposal costs could be achieved if an acceptable waste form can be produced with a high sodium molarity salt solution combined with a high water to premix (or dry blend) ratio. The objectives of this study were to evaluate the factors involved with increasing the sodium concentration in Cast Stone, including production and performance properties and the retention and release of specific components of interest. Three factors were identified for the experimental matrix: the concentration of sodium in the simulated salt solution, the water to premix ratio, and the blast furnace slag portion of the premix. The salt solution simulants used in this study were formulated to represent the overall average waste composition. The cement, blast furnace slag, and fly ash were sourced from a supplier in the Hanford area in order to be representative. The test mixes were prepared in the laboratory and fresh properties were measured. Fresh density increased with increasing sodium molarity and with decreasing water to premix ratio, as expected given the individual densities of these components. Rheology measurements showed that all of the test mixes produced very fluid slurries. The fresh density and rheology data are of potential value in designing a future Cast Stone production facility. Standing water and density gradient testing showed that settling is not of particular concern for the high sodium compositions studied. Heat of hydration measurements may provide some insight into the reactions that occur within the test mixes, which may in turn be related to the properties and performance of the waste form. These measurements showed that increased sodium

  17. Cast Stone Formulation At Higher Sodium Concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Fox, K. M.; Roberts, K. A.; Edwards, T. B.

    2014-02-28

    A low temperature waste form known as Cast Stone is being considered to provide supplemental Low Activity Waste (LAW) immobilization capacity for the Hanford site. Formulation of Cast Stone at high sodium concentrations is of interest since a significant reduction in the necessary volume of Cast Stone and subsequent disposal costs could be achieved if an acceptable waste form can be produced with a high sodium molarity salt solution combined with a high water to premix (or dry blend) ratio. The objectives of this study were to evaluate the factors involved with increasing the sodium concentration in Cast Stone, including production and performance properties and the retention and release of specific components of interest. Three factors were identified for the experimental matrix: the concentration of sodium in the simulated salt solution, the water to premix ratio, and the blast furnace slag portion of the premix. The salt solution simulants used in this study were formulated to represent the overall average waste composition. The cement, blast furnace slag, and fly ash were sourced from a supplier in the Hanford area in order to be representative. The test mixes were prepared in the laboratory and fresh properties were measured. Fresh density increased with increasing sodium molarity and with decreasing water to premix ratio, as expected given the individual densities of these components. Rheology measurements showed that all of the test mixes produced very fluid slurries. The fresh density and rheology data are of potential value in designing a future Cast Stone production facility. Standing water and density gradient testing showed that settling is not of particular concern for the high sodium compositions studied. Heat of hydration measurements may provide some insight into the reactions that occur within the test mixes, which may in turn be related to the properties and performance of the waste form. These measurements showed that increased sodium

  18. Cast Stone Formulation At Higher Sodium Concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Fox, K. M.; Roberts, K. A.; Edwards, T. B.

    2013-09-17

    A low temperature waste form known as Cast Stone is being considered to provide supplemental Low Activity Waste (LAW) immobilization capacity for the Hanford site. Formulation of Cast Stone at high sodium concentrations is of interest since a significant reduction in the necessary volume of Cast Stone and subsequent disposal costs could be achieved if an acceptable waste form can be produced with a high sodium molarity salt solution combined with a high water to premix (or dry blend) ratio. The objectives of this study were to evaluate the factors involved with increasing the sodium concentration in Cast Stone, including production and performance properties and the retention and release of specific components of interest. Three factors were identified for the experimental matrix: the concentration of sodium in the simulated salt solution, the water to premix ratio, and the blast furnace slag portion of the premix. The salt solution simulants used in this study were formulated to represent the overall average waste composition. The cement, blast furnace slag, and fly ash were sourced from a supplier in the Hanford area in order to be representative. The test mixes were prepared in the laboratory and fresh properties were measured. Fresh density increased with increasing sodium molarity and with decreasing water to premix ratio, as expected given the individual densities of these components. Rheology measurements showed that all of the test mixes produced very fluid slurries. The fresh density and rheology data are of potential value in designing a future Cast Stone production facility. Standing water and density gradient testing showed that settling is not of particular concern for the high sodium compositions studied. Heat of hydration measurements may provide some insight into the reactions that occur within the test mixes, which may in turn be related to the properties and performance of the waste form. These measurements showed that increased sodium

  19. Working with grocers to reduce dietary sodium: lessons learned from the Broome County Sodium Reduction in Communities pilot project.

    Science.gov (United States)

    Johnston, Yvonne A; McFadden, Mary; Lamphere, Marissa; Buch, Karen; Stark, Beth; Salton, Judith Lynn

    2014-01-01

    The purpose of this article is to describe implementation of and lessons learned from the Broome County Sodium Reduction in Communities grocery store initiative. This pilot project was conducted in collaboration with a regional supermarket chain and endeavored to develop population-based strategies for reducing sodium intake. Key interventions included marketing strategies, taste test demonstrations, and a public media campaign. Project staff worked closely with corporate registered dietitian nutritionists, a nutrition specialist, and an advertising agency in its development and implementation. A social marketing approach was used to educate consumers about the hidden sources of dietary sodium, to raise awareness of the adverse health effects of excess sodium intake, to encourage consumers to read food labels, and to urge them to purchase food items lower in sodium. The lessons learned from this experience may be of assistance to other communities that seek to implement similar sodium-reduction strategies in the grocery store environment.

  20. Quaternary liquid/liquid equilibria of sodium sulfate, sodium sulfite and water with two solvents: Acetone and 2-propanol

    Energy Technology Data Exchange (ETDEWEB)

    Schiozer, A.L.

    1994-03-01

    Aqueous solutions of sodium sulfate and sodium sulfite are produced from sodium carbonate in flue-gas scrubbers; recovery of these salts often requires multi-effect evaporators; however, a new energy-efficient unit operation called extractive crystallization has been shown to have reduced energy costs. In this process, an organic solvent is added to the aqueous salt solution to precipitate salt. Acetone is a suitable solvent for this process, better than 2-propanol. Liquid/liquid/solid equilibria for ternary systems containing a salt, water, and an organic solvent were measured. Systems investigated were sodium sulfite/water/acetone and sodium sulfite/water/2-propanol. Experiments were conducted at salt saturation covering a temperature range between the lower consolute temperature and 48.6{degrees}C. In the attempt to improve the extractive crystallization process for recovery of sodium sulfate from flue-gas scrubbers, attention was given to a feed containing a mixture of sodium sulfite and sodium sulfate. Liquid-liquid equilibria for quaternary systems containing two salts, water, and an organic solvent were experimentally determined at 35{degrees}C. The systems investigated were sodium sulfate/sodium sulfite/water/acetone and sodium sulfate/sodium sulfite/water/2propanol. The systems were studied at three salt ratios. For each salt ratio, experiments were conducted starting at saturation, water was then added until the one-phase region was reached. Mixtures of the two salts proved to have a small disadvantage relative to the 100 % sulfate feed process. Therefore, a sulfate-based extractive crystallization process is recommended.