WorldWideScience

Sample records for biphasic extraction system

  1. Ionic-Liquid-Based Acidic Aqueous Biphasic Systems for Simultaneous Leaching and Extraction of Metallic Ions.

    Science.gov (United States)

    Gras, Matthieu; Papaiconomou, Nicolas; Schaeffer, Nicolas; Chainet, Eric; Tedjar, Farouk; Coutinho, Joao A P; Billard, Isabelle

    2018-02-05

    The first instance of an acidic aqueous biphasic system (AcABS) based on tributyltetradecyl phosphonium chloride ([P 44414 ][Cl]) and an acid is here reported. This AcABS exhibits pronounced thermomorphic behavior and is shown to be applicable to the extraction of metal ions from concentrated acidic solutions. Metal ions such as cobalt(II), iron(III), platinum(IV) and nickel(II) are found to partition preferentially to one of the phases of the acidic aqueous biphasic system and it is here shown that it successfully allows the difficult separation of Co II from Ni II , here studied at 24 and 50 °C. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Improved extraction of fluoroquinolones with recyclable ionic-liquid-based aqueous biphasic systems.

    Science.gov (United States)

    Almeida, Hugo F D; Freire, Mara G; Marrucho, Isabel M

    2016-05-07

    In the past few years, the improvement of advanced analytical tools allowed to confirm the presence of trace amounts of metabolized and unchanged active pharmaceutical ingredients (APIs) in wastewater treatment plants (WWTPs) as well as in freshwater surfaces. It is known that the continuous contact with APIs, even at very low concentrations (ng L -1 -μg L -1 ), leads to serious human health problems. In this context, this work shows the feasibility of using ionic-liquid-based aqueous biphasic systems (IL-based ABS) in the extraction of quinolones present in aqueous media. In particular, ABS composed of imidazolium- and phosphonium-based ILs and aluminium-based salts (already used in water treatment plants) were evaluated in one-step extractions of six fluoroquinolones (FQs), namely ciprofloxacin, enrofloxacin, moxifloxacin, norfloxacin, ofloxacin and sarafloxacin, and extraction efficiencies up to 98% were obtained. Despite the large interest devoted to IL-based ABS as extractive systems of outstanding performance, their recyclability/reusability has seldomly been studied. An efficient extraction/cleaning process of the IL-rich phase is here proposed by FQs induced precipitation. The recycling of the IL and its further reuse without losses in the ABS extractive performance for FQs were established, as confirmed by the four consecutive removal/extraction cycles evaluated. This novel recycling strategy supports IL-based ABS as sustainable and cost-efficient extraction platforms.

  3. Electrochemical assessment of water|ionic liquid biphasic systems towards cesium extraction from nuclear waste

    International Nuclear Information System (INIS)

    Stockmann, T. Jane; Zhang, Jing; Montgomery, Anne-Marie; Ding, Zhifeng

    2014-01-01

    Highlights: • Electroanalytical chemistry was employed to assess cesium ion extraction in biphasic systems. • Water|ionic liquid systems are much more efficient than traditional water|organic ones. • The metal ion to ligand stoichiometry and overall complexation constant were determined. • The stoichiometry was confirmed by mass spectrometry. • The ligand CMPO used in TRUEX processes was found to be effective for the FIT. - Abstract: A room temperature ionic liquid (IL) composed of a quaternary alkylphosphonium (trihexyltetradecylphosphonium, P 66614 + ) and tetrakis(pentafluorophenyl)borate anion (TB − ) was employed within a water|P 66614 TB (w|P 66614 TB or w|IL) biphasic system to evaluate cesium ion extraction in comparison to that with a traditional water|organic solvent (w|o) combination. 137 Cs is a major contributor to the radioactivity of spent nuclear fuel as it leaves the reactor, and its extraction efficiency is therefore of considerable importance. The extraction was facilitated by the ligand octyl(phenyl)-N,N′-diisobutylcarbamoylphosphine oxide (CMPO) used in TRans-Uranium EXtraction processes and investigated through well established liquid|liquid electrochemistry. This study gave access to the metal ion to ligand (1:n) stoichiometry and overall complexation constant, β, of the interfacial complexation reaction which were determined to be 1:3 and 1.6 × 10 11 at the w|P 66614 TB interface while the study at w|o elicited an n equal to 1 with β equal to 86.5. Through a straightforward relationship, these complexation constant values were converted to distribution coefficients, δ α , with the ligand concentrations studied for comparison to other studies present in the literature; the w|o and w|IL systems gave δ α of 2 and 8.2 × 10 7 , respectively, indicating a higher overall extraction efficiency for the latter. For the w|o system, the metal ion-ligand stoichiometries were confirmed through isotopic distribution analysis of mass

  4. AQUEOUS BIPHASE EXTRACTION FOR PROCESSING OF FINE COAL

    Energy Technology Data Exchange (ETDEWEB)

    K. Osseo-Asare; X. Zeng

    2002-01-01

    The objective of this research project is to develop an aqueous biphase extraction process for the treatment of fine coals. Aqueous biphase extraction is an advanced separation technology that relies on the ability of an aqueous system consisting of a water-soluble polymer and another component, e.g., another polymer, an inorganic salt, or a nonionic surfactant, to separate into two immiscible aqueous phases. The principle behind the partition of solid particles in aqueous biphase systems is the physicochemical interaction between the solid surface and the surrounding liquid solution. In order to remove sulfur and mineral matter from fine coal with aqueous biphasic extraction, it is necessary to know the partitioning behavior of coal, as well as the inorganic mineral components. Therefore, in this research emphasis was placed on the partitioning behavior of fine coal particles as well as model fine inorganic particles in aqueous biphase systems.

  5. AQUEOUS BIPHASE EXTRACTION FOR PROCESSING OF FINE COAL; FINAL

    International Nuclear Information System (INIS)

    K. Osseo-Asare; X. Zeng

    2002-01-01

    The objective of this research project is to develop an aqueous biphase extraction process for the treatment of fine coals. Aqueous biphase extraction is an advanced separation technology that relies on the ability of an aqueous system consisting of a water-soluble polymer and another component, e.g., another polymer, an inorganic salt, or a nonionic surfactant, to separate into two immiscible aqueous phases. The principle behind the partition of solid particles in aqueous biphase systems is the physicochemical interaction between the solid surface and the surrounding liquid solution. In order to remove sulfur and mineral matter from fine coal with aqueous biphasic extraction, it is necessary to know the partitioning behavior of coal, as well as the inorganic mineral components. Therefore, in this research emphasis was placed on the partitioning behavior of fine coal particles as well as model fine inorganic particles in aqueous biphase systems

  6. Enhanced extraction of bovine serum albumin with aqueous biphasic systems of phosphonium- and ammonium-based ionic liquids

    Science.gov (United States)

    Pereira, Matheus M.; Pedro, Sónia N.; Quental, Maria V.; Lima, Álvaro S.; Coutinho, João A. P.; Freire, Mara G.

    2016-01-01

    Novel aqueous biphasic systems (ABS) composed of phosphonium- or ammonium-based ionic liquids (ILs), combined with a buffered aqueous solution of potassium citrate/citric acid (pH=7.0), were investigated for the extraction of proteins. For that purpose, the phase diagrams, tie-lines and tie-line lengths were determined at 25ºC, and the performance of these ABS for the extraction of bovine serum albumin (BSA) was then evaluated. The obtained results reveal that, with the exception of the more hydrophobic ILs, most of the systems investigated allow the complete extraction of BSA for the IL-rich phase in a single-step. These remarkable extraction efficiencies are far superior to those afforded by more conventional extraction systems previously reported. The composition of the biphasic systems, i.e., the amount of phase-forming components, was also investigated aiming at reducing the overall costs of the process without losing efficiency on the protein extraction. It is shown that the extraction efficiencies of BSA are maintained at 100% up to high protein concentrations (at least up to 10 g.L-1). The recovery of the BSA from the IL-rich phase by dialysis is also shown in addition to the demonstration of the IL recyclability and reusability, at least for 3 times. In the sequential three-step extractions (BSA recovery/IL reusability), the extraction efficiencies of BSA for the IL-rich phase were maintained at 100%. For the improved ABS, the preservation of the protein native conformation was confirmed by Size Exclusion High-Performance Liquid Chromatography (used also as the quantification method) and by Fourier Transform Infra-Red spectroscopy. According to the results herein reported, ABS composed of phosphonium- or ammonium-based ILs and a biodegradable organic salt represent an alternative and remarkable platform for the extraction of BSA and may be extended to other proteins of interest. PMID:25865275

  7. Improving the extraction and purification of immunoglobulin G by the use of ionic liquids as adjuvants in aqueous biphasic systems

    Science.gov (United States)

    Mondal, Dibyendu; Coutinho, João A. P.; Freire, Mara G.

    2017-01-01

    Immunoglobulins G (IgG) could become widespread biopharmaceuticals if cost-efficient processes for their extraction and purification are available. In this work, aqueous biphasic systems (ABS) composed of polyethylene glycols and a buffered salt, and with ionic liquids (ILs) as adjuvants, have been studied as alternative extraction and purification platforms of IgG from a rabbit serum source. Eleven ILs were investigated to provide insights on the chemical features which maximize the IgG partitioning. It is shown that in polymer-salt systems pure IgG preferentially partitions to the polymer-rich phase; yet, the complete extraction was never attained. Remarkably, after the addition of 5 wt% of adequate ILs to polymer-salt ABS, the complete extraction of pure IgG in a single-step was accomplished. The best systems and conditions were then applied to the extraction and purification of IgG directly from rabbit serum samples. The complete extraction of IgG in a single-step was maintained while its purity in the polymer-rich phase was enhanced by ca. 37% as compared to the IL-free ABS. The antibody stability was also evaluated revealing that appropriate ILs are able to maintain the IgG stability and can be used as phase-forming components of ABS when envisaging the purification of high-cost biopharmaceuticals. PMID:27568168

  8. Metal separations using aqueous biphasic partitioning systems

    International Nuclear Information System (INIS)

    Chaiko, D.J.; Zaslavsky, B.; Rollins, A.N.; Vojta, Y.; Gartelmann, J.; Mego, W.

    1996-01-01

    Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that the authors have studied are generated by combining an aqueous salt solution with an aqueous polymer solution. They have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. They have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS). In this report they review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation

  9. Actinide recovery using aqueous biphasic extraction: Initial developmental studies

    International Nuclear Information System (INIS)

    Chaiko, D.J.; Mensah-Biney, R.; Mertz, C.J.; Rollins, A.N.

    1992-08-01

    Aqueous biphasic extraction systems are being developed to treat radioactive wastes. The separation technique involves the selective partitioning of either solutes or colloid-size particles between two scible aqueous phases. Wet grinding of plutonium residues to an average particle size of one micron will be used to liberate the plutonium from the bulk of the particle matrix. The goal is to produce a plutonium concentrate that will integrate with existing and developing chemical recovery processes. Ideally, the process would produce a nonTRU waste stream. Coupling physical beneficiation with chemical processing will result in a substantial reduction in the volume of mixed wastes generated from dissolution recovery processes. As part of this program, we will also explore applications of aqueous biphasic extraction that include the separation and recovery of dissolved species such as metal ions and water-soluble organics. The expertise and data generated in this work will form the basis for developing more cost-effective processes for handling waste streams from environmental restoration and waste management activities within the DOE community. This report summarizes the experimental results obtained during the first year of this effort. Experimental efforts were focused on elucidating the surface and solution chemistry variables which govern partitioning behavior of plutonium and silica in aqueous biphasic extraction systems. Additional efforts were directed toward the development of wet grinding methods for producing ultrafine particles with diameters of one micron or less

  10. Actinide recovery using aqueous biphasic extraction: Initial developmental studies

    Energy Technology Data Exchange (ETDEWEB)

    Chaiko, D.J.; Mensah-Biney, R.; Mertz, C.J.; Rollins, A.N.

    1992-08-01

    Aqueous biphasic extraction systems are being developed to treat radioactive wastes. The separation technique involves the selective partitioning of either solutes or colloid-size particles between two scible aqueous phases. Wet grinding of plutonium residues to an average particle size of one micron will be used to liberate the plutonium from the bulk of the particle matrix. The goal is to produce a plutonium concentrate that will integrate with existing and developing chemical recovery processes. Ideally, the process would produce a nonTRU waste stream. Coupling physical beneficiation with chemical processing will result in a substantial reduction in the volume of mixed wastes generated from dissolution recovery processes. As part of this program, we will also explore applications of aqueous biphasic extraction that include the separation and recovery of dissolved species such as metal ions and water-soluble organics. The expertise and data generated in this work will form the basis for developing more cost-effective processes for handling waste streams from environmental restoration and waste management activities within the DOE community. This report summarizes the experimental results obtained during the first year of this effort. Experimental efforts were focused on elucidating the surface and solution chemistry variables which govern partitioning behavior of plutonium and silica in aqueous biphasic extraction systems. Additional efforts were directed toward the development of wet grinding methods for producing ultrafine particles with diameters of one micron or less.

  11. Host-Guest Inclusion Complexes between Amlodipine Enantiomers in Biphasic Recognition Chiral Extraction System using Tartaric Acid and β-Cyclodextrin Derivatives as Positive Confirmation Using of their Enantioselective Extraction

    OpenAIRE

    AZZAM, Khaldun; ABDALLAH, Hassan; HALIM, Hairul; AHMAD, Maizatul; SHAIBAH, Hassan

    2015-01-01

    The current work reports an extended theoretical study from our previous experimental work for the enantioselective extraction of amlodipine enantiomers in a biphasic recognition chiral extraction system (BRCES) consisting of hydrophobic D-diisopropyl tartrate dissolved in organic phase (n-decanol) and hydrophilic hydroxypropyl-?-cyclodextrin (HP-?-CD) in aqueous phase (acetate buffer) which preferentially recognize the R-enantiomer and S-enantiomer, respectively. The calculations were simula...

  12. Pseudo-biphasic extraction and liquid membrane transport of ionic solutes using micelle-based processes

    International Nuclear Information System (INIS)

    Tondre, Ch.

    1995-01-01

    Different aspects between micellar extraction and solvent extraction were discussed. One way of using micellar systems to perform metal ion extraction consists in solubilizing lipophilic complexing agents in the hydrophobic core of the micelles, similarly to their solubilization in the organic phase in classical biphasic extraction. Metal ions dissolved in the continuous phase will be complexed or not, depending on their affinity for the micelle-solubilized extractant, the microscopic micelle/water interface playing a part analogous to the macroscopic organic/water interface in biphasic extraction. The yields of extraction (after ultrafiltration of the micellar pseudo-phase) when parameters such as the extractant/metal ratio or the extractant hydrophobicity are changed, show similar trends as those reported in the case of solvent extraction, but only diluted solutions can be treated that way. 14 refs

  13. The laws governing ionic liquid extraction of cations: partition of 1-ethylpyridinium monocation and paraquat dication in ionic liquid/water biphasic systems.

    Science.gov (United States)

    Hamamoto, Takuya; Okai, Miho; Katsuta, Shoichi

    2015-05-21

    To find the laws governing the extraction of cations from aqueous solutions into hydrophobic ionic liquids (ILs), we investigated the partition of 1-ethylpyridinium monocation and paraquat (1,1'-dimethyl-4,4'-bipyridinium) dication in various IL/water biphasic systems. Ten different ILs of 1-butyl-3-methylimidazolium-based or bis(trifluoromethanesulfonyl)amide-based salts were used. The distribution ratio of the target cations (T(n+)) was dependent on the initial concentration in the aqueous phase and also very sensitive to the kind of IL. The behavior was quantitatively explained on the basis of a model in which the extraction goes through both the ion exchange and ion pair transfer processes, while keeping the product of the aqueous concentrations of the IL constituent ions a constant value (solubility product, Ksp). The distribution ratio of T(n+) is expressed as a function of the difference between the initial and equilibrium concentrations of T(n+) in the aqueous phase (Δ[T(n+)]W), the aqueous solubility of IL (Ksp(1/2)), and the cation valence n. The distribution ratio is a nearly constant value (D0) when Δ[T(n+)]W ≪ Ksp(1/2)/n and decreases inversely proportional to the nth power of Δ[T(n+)]W when Δ[T(n+)]W ≫ Ksp(1/2)/n. The log D0 versus log Ksp(1/2) plot gives a linear relationship with a slope of +n for the ILs with the same anion but different cations and that with a slope of nearly -n for the ILs with the same cation but different anions. This means that the extractability dependence on the kinds of IL constituent ions is greater for the divalent cation than for the monovalent one.

  14. AQUEOUS BIPHASE EXTRACTION FOR PROCESSING OF FINE COAL

    Energy Technology Data Exchange (ETDEWEB)

    K. Osseo-Asare; X. Zeng

    2001-06-30

    Ever-stringent environmental constraints dictate that future coal cleaning technologies be compatible with micron-size particles. This research program seeks to develop an advanced coal cleaning technology uniquely suited to micron-size particles, i.e., aqueous biphase extraction. The partitioning behaviors of silica in the polyethylene glycol (PEG)/dextran (Dex) and dextran/Triton X-100 (TX100) systems have been investigated, and the effects of sodium dodecylsulfate (SDS) and dodecyltrimethylammonium bromide (DTAB) on solid partition have been studied. In both biphase systems, silica particles stayed in the top PEG-rich phase at low pH. With increase in pH, the particles moved from the top phase to the interface, then to the bottom phase. At very high pH, the solids preferred the top phase again. These trends are attributable to variations in the polymer/solid and nonionic surfactant/solid interactions. Addition of ionic surfactants into these two systems introduces a weakly charged environment, since ionic surfactants concentrate into one phase, either the top phase or the bottom phase. Therefore, coulombic forces also play a key role in the partition of silica particles because electrostatic attractive or repulsive forces are produced between the solid surface and the ionic-surfactant-concentrated phase. For the PEG/dextran system in the presence of SDS, SiO{sub 2} preferred the bottom dextran-rich phase above its pH{sub PZC}. However, addition of DTAB moved the oxide particles from the top phase to the interface, and then to the bottom phase, with increase in pH. These different behaviors are attributable to the fact that SDS and DTAB concentrated into the opposite phase of the PEG/dextran system. On the other hand, in the dextran/Triton X-100 system, both ionic surfactants concentrated in the top surfactant-rich phase and formed mixed micelles with TX100. Therefore, addition of the anionic surfactant, SDS, moved the silica particles from top phase to the

  15. A method for separating water soluble organics from a process stream by aqueous biphasic extraction

    Energy Technology Data Exchange (ETDEWEB)

    Chaiko, David J.; Mego, William A.

    1997-12-01

    The present invention relates to a method for separating water-miscible organic species from a process stream by aqueous biphasic extraction. In particular, the method includes extracting the organic species into a polymer-rich phase of an aqueous biphase system in which the process stream comprises the salt-rich phase, and, next, separating the polymer from the extracted organic species by contacting the loaded, polymer-rich phase with a water-immiscible organic phase. Alternatively, the polymer can be separated from the extracted organic species by raising the temperature of the loaded, polymer-rich phase above the cloud point, such that the polymer and the water-soluble organic species separate into two distinct aqueous phases. In either case, a substantially salt-free, concentrated aqueous solution containing the organic species is recovered.

  16. Evaluation of the Capability of Ionic Liquid-Amino Acid Aqueous Systems for the Formation of Aqueous Biphasic Systems and Their Applications in Extraction.

    Science.gov (United States)

    Noshadi, Sajjad; Sadeghi, Rahmat

    2017-03-30

    To obtain further experimental evidence for a better understanding of the molecular mechanisms responsible for the soluting-out effect phenomena in ternary systems composed of an ionic liquid (IL), amino acid, and water, systematic studies on the vapor-liquid, liquid-liquid, and solid-liquid equilibrium behavior of aqueous solutions of several ILs were carried out in the presence of a range of amino acids. Water activities for binary and ternary aqueous solutions containing 1-butyl-3-methylimidazolium chloride, [C 4 mim]Cl, 1-hexyl-3-methylimidazolium chloride, [C 6 mim]Cl, 1-butyl-3-methyl-imidazolium trifluoromethanesulfonate, [C 4 mim][CF 3 SO 3 ], l-Ser, Gly, Ala, and l-Pro were measured using both vapor pressure osmometry and isopiestic methods. All of the ternary IL + amino acid + water systems show negative deviations from semi-ideal behavior and therefore soluting-out effects have been observed in these systems. In the case of the [C 4 mim][CF 3 SO 3 ] + amino acids aqueous systems, the IL is soluted-out by the amino acids and the soluting-out effect appears by aqueous biphasic system formation. For these systems, the phase diagram and partition coefficient of caffeine were measured at 298.15 K. However, for the [C 4 mim]Cl and [C 6 mim]Cl containing systems, the amino acids are soluted-out by the ILs and the soluting-out effect appears by precipitation of the amino acids from the solution, and the solubilities of the amino acids in the aqueous solutions decrease in the presence of [C 4 mim]Cl and [C 6 mim]Cl.

  17. A Framework for the Modelling of Biphasic Reacting Systems

    DEFF Research Database (Denmark)

    Anantpinijwatna, Amata; Sin, Gürkan; O’Connell, John P.

    2014-01-01

    Biphasic reacting systems have a broad application range from organic reactions in pharmaceutical and agro-bio industries to CO 2 capture. However, mathematical modelling of biphasic reacting systems is a formidable challenge due to many phenomena underlying the process such as chemical equilibrium...

  18. Applications of ionic liquids in biphasic separation: Aqueous biphasic systems and liquid-liquid equilibria.

    Science.gov (United States)

    Shukla, Shashi Kant; Pandey, Shubha; Pandey, Siddharth

    2017-10-10

    Ionic liquids (ILs) have been receiving much attention in many fields of analytical chemistry because of their various interesting properties which distinguish them from volatile organic compounds. They offer both directional and non-directional forces towards a solute molecule and therefore act as excellent solvents for a wide range of polar and non-polar compounds. Because of the presence of various possible interactions, ILs easily undergo biphasic separation with water and other less polar/non-polar organic solvents. Their ability to create biphasic splitting makes them a promising candidate for liquid-liquid separation processes, such as aqueous biphasic systems and liquid-liquid equilibria. Various aspects of ILs in these separation methods are discussed in view of the origin of physical forces responsible for the biphasic interactions, the effect of structural components, temperature, pressure, pH and additives. The specific advantages of using ILs in aqueous biphasic systems and liquid-liquid equilibria in binary and ternary systems are discussed with a view to defining their future role in separation processes by giving major emphasis on developing non-toxic ILs with physical and solution properties tailored to the needs of specific sample preparation techniques. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Host-Guest Inclusion Complexes between Amlodipine Enantiomers in the Biphasic Recognition Chiral Extraction System using Tartaric Acid and β-Cyclodextrin Derivatives as Positive Confirmation by using their Enantioselective Extraction.

    Science.gov (United States)

    Al Azzam, Khaldun M; Abdallah, Hassan H; Halim, Hairul N Abdul; Ahmad, Maizatul Akmam; Shaibah, Hassan

    2015-01-01

    The current work reports an extended theoretical study from our previous experimental work for the enantioselective extraction of amlodipine enantiomers in a biphasic recognition chiral extraction system (BRCES) consisting of hydrophobic D-diisopropyl tartrate dissolved in organic phase (n-decanol) and hydrophilic hydroxypropyl-β-cyclodextrin (HP-β-CD) in aqueous phase (acetate buffer) which preferentially recognize the R-enantiomer and S-enantiomer, respectively. The calculations were simulated using a semi-empirical PM3 method as a part of the Gaussian09 software package and were used to optimize the structures of the hosts, guests, and host-guest complexes in the gas phase without any restrictions. It was found that HP-β-CD has the strongest recognition ability among the three β-CD derivatives studied, namely HP-β-CD, hydroxyethyl-β-cyclodextrin (HE-β-CD), and methylated-β-cyclodextrin (Me-β-CD), due to the large interaction energies (Ecomp = -14.3025 kcal/ mol), while D-diisopropyl tartrate has the strongest ability among the four tartaric acid derivatives studied namely; L-diisopropyl tartrate, D-diisopropyl tartrate, L-diethyl tartrate, and D-diethyl tartrate (Ecomp = -5.9964 kcal/ mol). The computational calculations for the enantioselective partitioning of amlodipine enantiomers rationalized the reasons for the different behaviors for this extraction. The present theoretical results may be informative to scientists who are devoting themselves to developing models for their experimental parts or for enhancing the hydrophobic drug solubility in drug delivery systems.

  20. Host-Guest Inclusion Complexes between Amlodipine Enantiomers in the Biphasic Recognition Chiral Extraction System using Tartaric Acid and β-Cyclodextrin Derivatives as Positive Confirmation by using their Enantioselective Extraction

    Science.gov (United States)

    Al Azzam, Khaldun M.; Abdallah, Hassan H.; Halim, Hairul N. Abdul; Ahmad, Maizatul Akmam; Shaibah, Hassan

    2015-01-01

    The current work reports an extended theoretical study from our previous experimental work for the enantioselective extraction of amlodipine enantiomers in a biphasic recognition chiral extraction system (BRCES) consisting of hydrophobic D-diisopropyl tartrate dissolved in organic phase (n-decanol) and hydrophilic hydroxypropyl-β-cyclodextrin (HP-β-CD) in aqueous phase (acetate buffer) which preferentially recognize the R-enantiomer and S-enantiomer, respectively. The calculations were simulated using a semi-empirical PM3 method as a part of the Gaussian09 software package and were used to optimize the structures of the hosts, guests, and host-guest complexes in the gas phase without any restrictions. It was found that HP-β-CD has the strongest recognition ability among the three β-CD derivatives studied, namely HP-β-CD, hydroxyethyl-β-cyclodextrin (HE-β-CD), and methylated-β-cyclodextrin (Me-β-CD), due to the large interaction energies (Ecomp = −14.3025 kcal/ mol), while D-diisopropyl tartrate has the strongest ability among the four tartaric acid derivatives studied namely; L-diisopropyl tartrate, D-diisopropyl tartrate, L-diethyl tartrate, and D-diethyl tartrate (Ecomp = −5.9964 kcal/ mol). The computational calculations for the enantioselective partitioning of amlodipine enantiomers rationalized the reasons for the different behaviors for this extraction. The present theoretical results may be informative to scientists who are devoting themselves to developing models for their experimental parts or for enhancing the hydrophobic drug solubility in drug delivery systems. PMID:26839848

  1. Polyethylene glycol-based aqueous biphasic systems: Inexpensive, nontoxic alternatives for Hanford tank remediation

    International Nuclear Information System (INIS)

    Rogers, R.D.; Bond, A.H.; Bauer, C.B.; Song, Y.; Zhang, J.; Chomko, R.R.

    1994-01-01

    The potential for cleaner, cheaper, safer separations technologies with polyethylene glycol (PEG)-based aqueous biphasic systems stems from the inexpensive, nontoxic, nonflammable nature, and general availability of the PEG and inorganic salts which form them, and the lack of organic diluent. The authors have demonstrated that simulants of the highly alkaline waste stored at Westinghouse Hanford will induce biphase formation when contacted with aqueous PEG-2000 solutions. They have also demonstrated that the long lived and environmentally mobile radioactive ions 99 TcO 4 - and 129 I - can be partitioned from the salt rich to the PEG-rich phase in these aqueous biphasic systems. In addition, they have shown that Group 1 and 2 cation extraction can be accomplished from highly alkaline systems via addition of an appropriate water-soluble extractant. This paper focuses on the factors affecting the distribution ratios and the work on developing a viable separations process

  2. Method for separating water soluble organics from a process stream by aqueous biphasic extraction

    Science.gov (United States)

    Chaiko, David J.; Mego, William A.

    1999-01-01

    A method for separating water-miscible organic species from a process stream by aqueous biphasic extraction is provided. An aqueous biphase system is generated by contacting a process stream comprised of water, salt, and organic species with an aqueous polymer solution. The organic species transfer from the salt-rich phase to the polymer-rich phase, and the phases are separated. Next, the polymer is recovered from the loaded polymer phase by selectively extracting the polymer into an organic phase at an elevated temperature, while the organic species remain in a substantially salt-free aqueous solution. Alternatively, the polymer is recovered from the loaded polymer by a temperature induced phase separation (cloud point extraction), whereby the polymer and the organic species separate into two distinct solutions. The method for separating water-miscible organic species is applicable to the treatment of industrial wastewater streams, including the extraction and recovery of complexed metal ions from salt solutions, organic contaminants from mineral processing streams, and colorants from spent dye baths.

  3. Aqueous biphasic extraction of uranium and thorium from contaminated soils. Final report

    International Nuclear Information System (INIS)

    Chaiko, D.J.; Gartelmann, J.; Henriksen, J.L.; Krause, T.R.; Deepak; Vojta, Y.; Thuillet, E.; Mertz, C.J.

    1995-07-01

    The aqueous biphasic extraction (ABE) process for soil decontamination involves the selective partitioning of solutes and fine particulates between two immiscible aqueous phases. The biphase system is generated by the appropriate combination of a water-soluble polymer (e.g., polyethlene glycol) with an inorganic salt (e.g., sodium carbonate). Selective partitioning results in 99 to 99.5% of the soil being recovered in the cleaned-soil fraction, while only 0.5 to 1% is recovered in the contaminant concentrate. The ABE process is best suited to the recovery of ultrafine, refractory material from the silt and clay fractions of soils. During continuous countercurrent extraction tests with soil samples from the Fernald Environmental Management Project site (Fernald, OH), particulate thorium was extracted and concentrated between 6- and 16-fold, while the uranium concentration was reduced from about 500 mg/kg to about 77 mg/kg. Carbonate leaching alone was able to reduce the uranium concentration only to 146 mg/kg. Preliminary estimates for treatment costs are approximately $160 per ton of dry soil. A detailed flowsheet of the ABE process is provided

  4. Generic Model-Based Tailor-Made Design and Analysis of Biphasic Reaction Systems

    DEFF Research Database (Denmark)

    Anantpinijwatna, Amata

    systems have a broad range of application, such as the manufacture of petroleum based chemicals, pharmaceuticals, and agro-bio products. Major considerations in the design and analysis of biphasic reaction systems are physical and chemical equilibria, kinetic mechanisms, and reaction rates. The primary...... different organic solvents leading to an improved and innovative design of the system.......Biphasic reaction systems are composed of immiscible aqueous and organic liquid phases where reactants, products, and catalysts are partitioned. These biphasic conditions point to novel synthesis paths, higher yields, and faster reactions, as well as facilitate product separation. The biphasic...

  5. Non-conventional solvents in liquid phase microextraction and aqueous biphasic systems.

    Science.gov (United States)

    An, Jiwoo; Trujillo-Rodríguez, María J; Pino, Verónica; Anderson, Jared L

    2017-06-02

    The development of rapid, convenient, and high throughput sample preparation approaches such as liquid phase microextraction techniques have been continuously developed over the last decade. More recently, significant attention has been given to the replacement of conventional organic solvents used in liquid phase microextraction techniques in order to reduce toxic waste and to improve selectivity and/or extraction efficiency. With these objectives, non-conventional solvents have been explored in liquid phase microextraction and aqueous biphasic systems. The utilized non-conventional solvents include ionic liquids, magnetic ionic liquids, and deep eutectic solvents. They have been widely used as extraction solvents or additives in various liquid phase microextraction modes including dispersive liquid-liquid microextraction, single-drop microextraction, hollow fiber-liquid phase microextraction, as well as in aqueous biphasic systems. This review provides an overview into the use of non-conventional solvents in these microextraction techniques in the past 5 years (2012-2016). Analytical applications of the techniques are also discussed. Copyright © 2017 Elsevier B.V. All rights reserved.

  6. Aqueous biphasic systems involving alkylsulfate-based ionic liquids

    Energy Technology Data Exchange (ETDEWEB)

    Deive, Francisco J. [Instituto de Tecnologia Quimica e Biologica, UNL, Av. Republica, Apartado 127, 2780-901 Oeiras (Portugal); Department of Chemical Engineering, University of Vigo, P.O. Box 36310, Vigo (Spain); Rodriguez, Ana [Department of Chemical Engineering, University of Vigo, P.O. Box 36310, Vigo (Spain); Marrucho, Isabel M., E-mail: imarrucho@itqb.unl.pt [Instituto de Tecnologia Quimica e Biologica, UNL, Av. Republica, Apartado 127, 2780-901 Oeiras (Portugal); Rebelo, Luis P.N. [Instituto de Tecnologia Quimica e Biologica, UNL, Av. Republica, Apartado 127, 2780-901 Oeiras (Portugal)

    2011-11-15

    Highlights: > K{sub 3}PO{sub 4}, K{sub 2}CO{sub 3}, Na{sub 2}CO{sub 3}, and (NH{sub 4}){sub 2}SO{sub 4} act as phase promoter in aqueous solutions of ILs. > Remarkable influence of alkyl-chain length on solubility curves of alkylsulfate-based ILs. > Merchuck correlation was used for describing these systems. > {Delta}S{sub hyd} and Hofmeister series were used to discuss the different salting out effects. - Abstract: The specific effects of K{sub 3}PO{sub 4}, K{sub 2}CO{sub 3}, Na{sub 2}CO{sub 3}, and (NH{sub 4}){sub 2}SO{sub 4}, as high charge-density inorganic salts and thus inducers of the formation of aqueous biphasic systems (ABS) containing several ethyl-methylimidazolium alkylsulfate ionic liquids, C{sub 2}MIM C{sub n}SO{sub 4} (n = 2, 4, 6, or 8), have been assessed at T = 298.15 K. The results are analyzed in the light of the Hofmeister series. The influence of different alkyl chain lengths in the anion, together with the ability of the selected inorganic salts to induce the formation of ABS, is discussed. Phase diagrams have been determined through turbidimetry, including tie lines assignments from mass phase ratios according to the lever - arm rule. The Merchuck equation was satisfactorily used to correlate the solubility curve.

  7. New technetium-99m generator technologies utilizing polyethylene glycol-based aqueous biphasic systems

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, R.D.; Bond, A.H.; Zhang, Jianhua [Northern Illinois Univ., De Kalb, IL (United States). Dept. of Chemistry; Horwitz, P. [Argonne National Lab., IL (United States)

    1995-12-31

    Two new schemes for TcO{sub 4}{sup {minus}}/MoO{sub 4}{sup 2{minus}} separations from OH{sup {minus}} and MoO{sub 4}{sup 2{minus}} media using polyethylene glycol (PEG)-based aqueous biphasic systems (ABS) have been developed. The two most important salt solutions in current {sup 99m}Tc-generator technologies, OH{sup {minus}} and MoO{sub 4}{sup 2{minus}}, also salt out PEG to form ABS. In liquid/liquid PEG- ABS, pertechnetate can be separated from molybdate with separation factors as high as 10,000. Stripping is accomplished by reduction of the TcO{sub 4}{sup {minus}} and back extraction into a salt solution. the strip solution can be the salt of an imaging agent (e.g., Na{sub 4}HEDPA) and thus may, under the appropriate conditions, be injected directly into the human body. {sup 99m}TcO{sub 4}{sup {minus}} can also be concentrated from a dilute load solution of {sup 99}MoO{sub 4}{sup 2{minus}} in NaOH using an aqueous biphasic extraction chromatographic technique (ABEC). A rinse with K{sub 2}CO{sub 3} assures that all {sup 99}MoO{sub 4}{sup 2{minus}} is removed from the column and this is confirmed by a rapid drop in {sup 99}Mo activity by the fourth free column volume (fcv) of rinse. The {sup 99m}TcO{sub 4}{sup {minus}} is then eluted with water. This chromatographic separation affords 94% of the {sup 99m}TcO{sub 4}{sup {minus}} activity in 5 fcv, with the y spectrum showing less than 2 {times} 10{sup {minus}4} of the original {sup 99}Mo activity.

  8. Single-Step Purification of Ovalbumin from Egg White Using Aqueous Biphasic Systems.

    Science.gov (United States)

    Pereira, Matheus M; Cruz, Rafaela A P; Almeida, Mafalda R; Lima, Álvaro S; Coutinho, João A P; Freire, Mara G

    2016-06-01

    The ability of aqueous biphasic systems (ABS) composed of polyethylene glycols of different molecular weights (PEG 400, 600 and 1000) and buffered aqueous solutions of potassium citrate/citric acid (pH = 5.0 - 8.0) to selectively extract ovalbumin from egg white was here investigated. Phase diagrams, tie-lines and tie-line lengths were determined at 25ºC and the partitioning of ovalbumin in these systems was then evaluated. Aiming at optimizing the selective extraction of ovalbumin in the studied ABS, factors such as pH, PEG molecular weight and amount of the phase-forming components were initially investigated with pure commercial ovalbumin. In almost all ABS, it was observed a preferential partitioning of ovalbumin to the polymer-rich phase, with extraction efficiencies higher than 90%. The best ABS were then applied in the purification of ovalbumin from the real egg white matrix. In order to ascertain on the ovalbumin purity and yield, sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE) and size exclusion high performance liquid chromatography (SE-HPLC) analyses were conducted, confirming that the isolation/purification of ovalbumin from egg white was completely achieved in a single-step with a recovery yield of 65%. The results obtained show that polymer-salt-based ABS allow the selective extraction of ovalbumin from egg white with a simpler approach and better performance than previously reported. Finally, it is shown that ovalbumin can be completely recovered from the PEG-rich phase by an induced precipitation using an inexpensive and sustainable separation platform which can be easily applied on an industrial scale.

  9. Subtle Effects of Aliphatic Alcohol Structure on Water Extraction and Solute Aggregation in Biphasic Water/ n -Dodecane

    Energy Technology Data Exchange (ETDEWEB)

    Knight, Andrew W.; Qiao, Baofu; Chiarizia, Renato; Ferru, Geoffroy; Forbes, Tori; Ellis, Ross J.; Soderholm, L.

    2017-04-03

    Organic phase aggregation behavior of 1-octanol and its structural isomer, 2-ethylhexanol, in a biphasic n-dodecane water system is studied with a combination of physical measurement, small-angle X-ray scattering (SAXS), and atomistic molecular dynamic simulations. Physical properties of the organic phases are probed following their mixing and equilibration with immiscible water phases. Studies reveal that the interfacial tension decreases as a function of increasing alcohol concentration over the solubility range of the alcohol with no evidence for a critical aggregate concentration (cac). An uptake of water into the organic phases is quantified, as a function of alcohol content, by Karl Fischer titrations. The extraction of water into dodecane was further assessed as a function of alcohol concentration via the slope-analysis method sometimes employed in chemical separations. This provides a qualitative understanding of solute (water/alcohol) aggregation in the organic phase. The physical results are supported by analyses of SAXS data that reveals an emergence of aggregates in n-dodecane at elevated alcohol concentrations. The observed aggregate structure is dependent on the alcohol tail group geometry, consistent with surfactant packing parameter. The formation of these aggregates is discussed at a molecular level, where alcohol-alcohol and alcohol-water H-bonding interactions likely dominate the occurrence and morphology of the aggregates.

  10. Recycling nanoparticle catalysts without separation based on a pickering emulsion/organic biphasic system.

    Science.gov (United States)

    Liu, Huifang; Zhang, Zhiming; Yang, Hengquan; Cheng, Fangqin; Du, Zhiping

    2014-07-01

    A conceptually novel methodology is explored for in situ recycling of nanoparticle catalysts based on transforming a conventional organic/aqueous biphasic system into a Pickering emulsion/organic biphasic system (PEOBS). The suggested PEOBS exists as two phases, with the nanoparticle catalyst "anchored" in the Pickering emulsion phase, but is "continuous" between the organic phase and the continuous phase of the Pickering emulsion. Aqueous hydrogenations are used to evaluate the reaction performances of PEOBS, and the underlying principles of PEOBS are preliminarily elaborated. The unique properties of PEOBS lead to many intriguing findings, which are unlikely to be achieved in the reported biphasic systems. PEOBS exhibits more than a fourfold enhancement in catalysis efficiency in comparison with a conventional biphasic system. Impressively, PEOBS enables the organic product to be facilely isolated through simple decantation and the nanoparticle catalyst can be recycled in situ without the need for "separation". Its recycling effectiveness is justified by ten reaction cycles without significant catalyst loss. The simple protocol, in conjunction with the stability to simultaneously achieve high catalysis efficiency and excellent catalyst recyclability, makes PEOBS a promising methodology to develop more sustainable nanocatalysis. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Comparison of the lysis-centrifugation and agitated biphasic blood culture systems for detection of fungemia.

    Science.gov (United States)

    Murray, P R

    1991-01-01

    Although the detection of fungemia has been improved by the use of vented or biphasic blood culture bottles, the best recovery and earliest detection have been reported in the Isolator lysis-centrifugation system. It was recently demonstrated that improved detection of both bacteria and fungi was accomplished by mechanically agitating blood culture bottles for the first 24 h of incubation. In this study the detection of fungemia by use of the Isolator system was compared with that of an agitated biphasic system. A total of 182 fungi were isolated from blood specimens inoculated into both culture systems. No difference in the overall recovery of fungi or individual species of yeasts was observed between the two systems. However, all seven isolates of Histoplasma capsulatum were recovered in the Isolator system only. The time required to detect fungemia with each of the two systems was also compared. No statistically significant difference was observed. From the data collected during this 18-month study, it can be concluded that the overall recovery and time of detection of yeasts are equivalent in the lysis-centrifugation system and the agitated biphasic blood culture system. The lysis-centrifugation system is still superior for the detection of filamentous fungi such as H. capsulatum. PMID:1993772

  12. Development of Modified-Release Tablets of Zolpidem Tartrate by Biphasic Quick/Slow Delivery System

    OpenAIRE

    Mahapatra, Anjan Kumar; Sameeraja, N. H.; Murthy, P. N.

    2014-01-01

    Zolpidem tartrate is a non-benzodiazepine analogue of imidazopyridine of sedative and hypnotic category. It has a short half-life with usual dosage regimen being 5 mg, two times a day, or 10 mg, once daily. The duration of action is considered too short in certain circumstances. Thus, it is desirable to lengthen the duration of action. The formulation design was implemented by preparing extended-release tablets of zolpidem tartrate using the biphasic delivery system technology, where sodium s...

  13. A hybrid composite system of biphasic calcium phosphate granules loaded with hyaluronic acid-gelatin hydrogel for bone regeneration.

    Science.gov (United States)

    Faruq, Omar; Kim, Boram; Padalhin, Andrew R; Lee, Gun Hee; Lee, Byong-Taek

    2017-10-01

    An ideal bone substitute should be made of biocompatible materials that mimic the structure, characteristics, and functions of natural bone. Many researchers have worked on the fabrication of different bone scaffold systems including ceramic-polymer hybrid system. In the present study, we incorporated hyaluronic acid-gelatin hydrogel to micro-channeled biphasic calcium phosphate granules as a carrier to improve cell attachment and proliferation through highly interconnected porous structure. This hybrid system is composed of ceramic biphasic calcium phosphate granules measuring 1 mm in diameter with seven holes and hyaluronic acid-gelatin hydrogel. This combination of biphasic calcium phosphate and hyaluronic acid-gelatin retained suitable characteristics for bone regeneration. The resulting scaffold had a porosity of 56% with a suitable pore sizes. The mechanical strength of biphasic calcium phosphate granule increased after loading hyaluronic acid-gelatin from 4.26 ± 0.43 to 6.57 ± 0.25 MPa, which is highly recommended for cancellous bone substitution. Swelling and degradation rates decreased in the hybrid scaffold compared to hydrogel due to the presence of granules in hybrid scaffold. In vitro cytocompatibility studies were observed by preosteoblasts (MC3T3-E1) cell line and the result revealed that biphasic calcium phosphate/hyaluronic acid-gelatin significantly increased cell growth and proliferation compared to biphasic calcium phosphate granules. Analysis of micro-computed tomography data and stained tissue sections from the implanted samples showed that the hybrid scaffold had good osseointegration and better bone formation in the scaffold one and two months postimplantation. Histological section confirmed the formation of dense collagenous tissue and new bone in biphasic calcium phosphate/hyaluronic acid-gelatin scaffolds at two months. Our study demonstrated that such hybrid biphasic calcium phosphate/hyaluronic acid-gelatin scaffold is a

  14. Enhancing productivity for cascade biotransformation of styrene to (S)-vicinal diol with biphasic system in hollow fiber membrane bioreactor.

    Science.gov (United States)

    Gao, Pengfei; Wu, Shuke; Praveen, Prashant; Loh, Kai-Chee; Li, Zhi

    2017-03-01

    Biotransformation is a green and useful tool for sustainable and selective chemical synthesis. However, it often suffers from the toxicity and inhibition from organic substrates or products. Here, we established a hollow fiber membrane bioreactor (HFMB)-based aqueous/organic biphasic system, for the first time, to enhance the productivity of a cascade biotransformation with strong substrate toxicity and inhibition. The enantioselective trans-dihydroxylation of styrene to (S)-1-phenyl-1,2-ethanediol, catalyzed by Escherichia coli (SSP1) coexpressing styrene monooxygenase and an epoxide hydrolase, was performed in HFMB with organic solvent in the shell side and aqueous cell suspension in the lumen side. Various organic solvents were investigated, and n-hexadecane was found as the best for the HFMB-based biphasic system. Comparing to other reported biphasic systems assisted by HFMB, our system not only shield much of the substrate toxicity but also deflate the product recovery burden in downstream processing as the majority of styrene stayed in organic phase while the diol product mostly remained in the aqueous phase. The established HFMB-based biphasic system enhanced the production titer to 143 mM, being 16-fold higher than the aqueous system and 1.6-fold higher than the traditional dispersive partitioning biphase system. Furthermore, the combination of biphasic system with HFMB prevents the foaming and emulsification, thus reducing the burden in downstream purification. HFMB-based biphasic system could serve as a suitable platform for enhancing the productivity of single-step or cascade biotransformation with toxic substrates to produce useful and valuable chemicals.

  15. Investigation of the salting-out of polyethylene glycol-2000 in aqueous biphasic systems

    International Nuclear Information System (INIS)

    Wodziak, E.; Zhang, J.; Rogers, R.D.

    1995-01-01

    We have been investigating the potential for the use of polyethylene glycol (PEG)-based aqueous biphasic systems in the separation of metal ions in such diverse fields as nuclear medicine, nuclear waste, and hydrometallurgy. PEG-based ABS may provide cheaper, cleaner, safer separation technologies. In order to realize this potential, we need to expand the number of known phase-forming salts and investigate their interactions with PEG. Phase diagrams are an invaluable tool for this purpose. In this presentation, systematic investigation of the salting-out ability of several phase-forming salts will be presented and their behavior discussed

  16. Thermodynamics of biphasic lanthanide extraction by tripodal diglycolamide: a solution calorimetry study

    NARCIS (Netherlands)

    Ansari, S.A.; Mohapatra, P.K.; Verboom, Willem; Rao, L.

    2016-01-01

    Isothermal titration calorimetry was employed for the direct measurement of the enthalpy of extraction (ΔHextr) of Eu(NO3)3 by using a tripodal diglycolamide (T-DGA) ligand dissolved in n-dodecane containing 5% (v/v) 2-decanol. The enthalpy of extraction obtained by titration calorimetry was in good

  17. Production of Phytotoxic Metabolite Using Biphasic Fermentation System from Strain C1136 of Lasiodiplodia pseudotheobromae, a Potential Bioherbicidal Agent

    Directory of Open Access Journals (Sweden)

    Charles Oluwaseun ADETUNJI

    2017-09-01

    Full Text Available Formulation of effective and environmental friendly bioherbicides depends on the type of fermentation medium used for the production of phytotoxic metabolites. The effect of biomass, colony forming unit and the phytotoxic metabolite produced from the biphasic fermentation was carried out, while the phytotoxic metabolite was tested in vivo and in-vitro on Echinochola crus-galli and dicotyledonous Chromolaena odorata. The mutant strain of Lasiodiplodia pseudotheobromae C1136 (Lp90 produced the highest amount of conidia and the largest necrotic area on the two tested weeds when compared to its wild strain in the different biphasic media combinations. The study revealed that the biphasic system containing PDB + rice produced the highest bioherbicidal activities. Therefore, the phytotoxic metabolites from strain C1136 are suggested for large scale production of bioherbicides for the management of weeds in conventional farming to improve yield and enhance food security.

  18. Pickering interfacial catalysis for biphasic systems: from emulsion design to green reactions.

    Science.gov (United States)

    Pera-Titus, Marc; Leclercq, Loïc; Clacens, Jean-Marc; De Campo, Floryan; Nardello-Rataj, Véronique

    2015-02-09

    Pickering emulsions are surfactant-free dispersions of two immiscible fluids that are kinetically stabilized by colloidal particles. For ecological reasons, these systems have undergone a resurgence of interest to mitigate the use of synthetic surfactants and solvents. Moreover, the use of colloidal particles as stabilizers provides emulsions with original properties compared to surfactant-stabilized emulsions, microemulsions, and micellar systems. Despite these specific advantages, the application of Pickering emulsions to catalysis has been rarely explored. This Minireview describes very recent examples of hybrid and composite amphiphilic materials for the design of interfacial catalysts in Pickering emulsions with special emphasis on their assets and challenges for industrially relevant biphasic reactions in fine chemistry, biofuel upgrading, and depollution. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Application of the e-KT-UNIFAC Model for the Improved and Innovative Design of Biphasic Reacting Systems

    DEFF Research Database (Denmark)

    Anantpinijwatna, Amata; Kim, Sun H.; Sales-Cruz, Mauricio

    2016-01-01

    Biphasic reacting systems contain effectively immiscible aqueous and organic liquid phases in which reactants, products, and catalysts can partition. These conditions allow novel synthesis paths, higher yields, and faster reactions, as well as facilitate product(s) separation. A systematic modeli...... of epoxidation of palm oil and production of furan derivatives....

  20. Kinetic studies on the Rhizomucor miehei lipase catalyzed esterification reaction of oleic acid with 1-butanol in a biphasic system

    NARCIS (Netherlands)

    Kraai, G.N.; Winkelman, J.G.M.; de Vries, Johannes; Heeres, H.J.

    2008-01-01

    The kinetics of the esterification of oleic acid with 1 -butanol catalyzed by free Rhizomucor miehei lipase in a biphasic system was studied in a batch reactor. The reaction appeared to proceed via a Ping Pong bi-bi mechanism with I -butanol inhibition. The kinetic constants of the model were

  1. Mass transfer studies in miniature Rotating Disc Contactor (RDC) with 30% TBP/nitric acid biphasic system

    International Nuclear Information System (INIS)

    Balasubramonian, S.; Sivakumar, D.; Kumar, Shekhar; Kamachi Mudali, U.

    2014-01-01

    The rotating disc contactor is the widely used liquid-liquid extraction equipment for its high throughput and efficiency. In this work mass transfer performance of the miniature RDC column for the 30% TBP/nitric acid biphasic system was studied in terms of the operating variables such as rotor speed and flow rate of the aqueous and organic phase. The RDC column used in the experiments was shown. The column shell is made up of thick glass having diameter of 10.5 cm and height 100 cm. The rotor diameter is 5.3 cm and stator opening diameter is 6.3 cm. Totally 25 number of rotor discs were welded in the rotating shaft. This shaft was aligned in such a way that each rotor was placed in the centre of the compartment formed in between the two stator rings. The experiments were carried out to study the effect of rotor speed and superficial velocity of the dispersed and continuous phase on mass transfer efficiency. The organic solvent was made as the continuous phase and O/A ratio was set as 4 in both the continuous to dispersed phase(c-d) and dispersed to continuous phase (d-c) mass transfer experiments. The Number of Transfer Units (NTU) was estimated based on the solvent phase. The graphical representation of NTU was shown. The NTU value was observed as 4 and 3 respectively for extraction and stripping at the combined through put of 60 L/h and the rotor speed of 1000 rpm. This corresponds to the Height of Transfer Unit (HTU) value of 15 cm and 20 cm respectively for d-c and c-d mass transfer. The estimated overall mass transfer coefficient was increasing with rotor speed and superficial velocity of the liquid phases. The overall mass transfer coefficient also increases with increase in hold up

  2. Modulating the Partitioning of Microparticles in a Polyethylene Glycol (PEG-Dextran (DEX Aqueous Biphasic System by Surface Modification

    Directory of Open Access Journals (Sweden)

    Chang Kyu Byun

    2018-02-01

    Full Text Available Aqueous two-phase systems (ATPSs or aqueous biphasic systems are useful for biological separation/preparation and cell micropatterning. Specifically, aqueous two-phase systems (ATPSs are not harmful to cells or biomaterials; therefore, they have been used to partition and isolate these materials from others. In this study, we suggest chemically modifying the surface of target materials (micro/nanoparticles, for example with polymers, such as polyethylene glycol and dextran, which are the same polymer solutes as those in the ATPS. As a simple model, we chemically coated polyethylene glycol or dextran to the surface of polystyrene magnetic particles and observed selective partitioning of the surface modified particles to the phase in which the same polymer solutes are dominant. This approach follows the principle “like dissolves like” and can be expanded to other aqueous biphasic or multiphasic systems while consuming fewer chemicals than the conventional modulation of hydrophobicities of solute polymers to control partitioning in aqueous biphasic or multiphasic systems.

  3. Liquid / liquid biphasic electrochemistry in ultra-turrax dispersed acetonitrile / aqueous electrolyte systems

    International Nuclear Information System (INIS)

    Watkins, John D.; Amemiya, Fumihiro; Atobe, Mahito; Bulman-Page, Philip C.; Marken, Frank

    2010-01-01

    Unstable acetonitrile | aqueous emulsions generated in situ with ultra-turrax agitation are investigated for applications in dual-phase electrochemistry. Three modes of operation for liquid / liquid aqueous-organic electrochemical processes are demonstrated with no intentionally added electrolyte in the organic phase based on (i) the formation of a water-soluble product in the aqueous phase in the presence of the organic phase, (ii) the formation of a product and ion transfer at the liquid / liquid-electrode triple phase boundary, and (iii) the formation of a water-insoluble product in the aqueous phase which then transfers into the organic phase. A three-electrode electrolysis cell with ultra-turrax agitator is employed and characterised for acetonitrile / aqueous 2 M NaCl two phase electrolyte. Three redox systems are employed in order to quantify the electrolysis cell performance. The one-electron reduction of Ru(NH 3 ) 6 3+ in the aqueous phase is employed to determine the rate of mass transport towards the electrode surface and the effect of the presence of the acetonitrile phase. The one-electron oxidation of n-butylferrocene in acetonitrile is employed to study triple phase boundary processes. Finally, the one-electron reduction of cobalticenium cations in the aqueous phase is employed to demonstrate the product transfer from the electrode surface into the organic phase. Potential applications in biphasic electrosynthesis are discussed.

  4. Development of modified-release tablets of zolpidem tartrate by biphasic quick/slow delivery system.

    Science.gov (United States)

    Mahapatra, Anjan Kumar; Sameeraja, N H; Murthy, P N

    2015-06-01

    Zolpidem tartrate is a non-benzodiazepine analogue of imidazopyridine of sedative and hypnotic category. It has a short half-life with usual dosage regimen being 5 mg, two times a day, or 10 mg, once daily. The duration of action is considered too short in certain circumstances. Thus, it is desirable to lengthen the duration of action. The formulation design was implemented by preparing extended-release tablets of zolpidem tartrate using the biphasic delivery system technology, where sodium starch glycolate acts as a superdisintegrant in immediate-release part and hydroxypropyl methyl cellulose as a release retarding agent in extended-release core. Tablets were prepared by direct compression. Both the core and the coat contained the drug. The pre-compression blends were evaluated for angle of repose, bulk density, and compressibility index. The tablets were evaluated for thickness, hardness, weight variation test, friability, and in vitro release studies. No interaction was observed between zolpidem tartrate and excipients from the Fourier transform infrared spectroscopy and differential scanning calorimetry analysis. The results of all the formulations prepared were compared with reference product Stilnoct®. Optimized formulations showed release patterns that match the United States Pharmacopeia (USP) guidelines for zolpidem tartrate extended-release tablets. The mechanism of drug release was studied using different mathematical models, and the optimized formulation has shown Fickian diffusion. Accelerated stability studies were performed on the optimized formulation.

  5. Information extraction system

    Science.gov (United States)

    Lemmond, Tracy D; Hanley, William G; Guensche, Joseph Wendell; Perry, Nathan C; Nitao, John J; Kidwell, Paul Brandon; Boakye, Kofi Agyeman; Glaser, Ron E; Prenger, Ryan James

    2014-05-13

    An information extraction system and methods of operating the system are provided. In particular, an information extraction system for performing meta-extraction of named entities of people, organizations, and locations as well as relationships and events from text documents are described herein.

  6. Biphasic thermoelectric materials derived from the half-Heusler/full-Heusler system Ti-Ni-Sn

    Science.gov (United States)

    Douglas, Jason Everett

    Among the possible avenues for increasing the efficiency of global energy usage, thermoelectrics are an exciting, solid-state option. Thermoelectric materials, which convert an internal temperature gradient into a voltage and vice versa, have found applications in refrigeration as well as power generation from waste heat. TiNiSn, a semiconductor of the half-Heusler (hH) crystal structure, is of particular interest due to its very favorable electronic transport properties, conductivity (sigma) and Seebeck coefficient ( S), at relevant temperature regimes (between 600 K and 900 K). Unfortunately, its overall efficiency is hampered by a comparatively high thermal conductivity (kappa). In the design of thermoelectric materials, a number of approaches have been taken to increase the thermoelectric figure of merit, ZT = ( S2sigma/kappa)T, where T is temperature. In this work we examine how microstructure can be used to alter these thermoelectric propertiesin a biphasic Ti-Ni-Sn materials containing full-Heusler (fH) TiNi2Sn embedded within hH thermoelectric TiNiSn. We explored a wide range of Ni compositions in TiNi1+xSn--from stoichiometric TiNiSn to high Heusler volume fraction, TiNi1.25Sn--materials prepared by levitation induction melting followed by annealing. Phase distributions and microstructure were characterized using synchrotron x-ray diffraction and optical and electron microscopy. In a sample of the nominal composition TiNi1.15Sn, a significant decrease in thermal conductivity (about 30%) is observed for the biphasic material despite the metallic second-phase particles existing at the micrometer scale; a 50% increase in the electrical conductivity is also measured. These result in a maximum figure of merit, ZT, of 0.44 at 800 K, which is 25% greater than is observed for the x = 0 sample. Density functional theory calculations using hybrid functionals were performed to determine band alignments between the half- and full-Heusler compounds, as well as

  7. Design and hydraulic characteristics of a field-scale bi-phasic bioretention rain garden system for storm water management.

    Science.gov (United States)

    Yang, H; Florence, D C; McCoy, E L; Dick, W A; Grewal, P S

    2009-01-01

    A field-scale bioretention rain garden system was constructed using a novel bi-phasic (i.e. sequence of anaerobic to aerobic) concept for improving retention and removal of storm water runoff pollutants. Hydraulic tests with bromide tracer and simulated runoff pollutants (nitrate-N, phosphate-P, Cu, Pb, and Zn) were performed in the system under a simulated continuous rainfall. The objectives of the tests were (1) to determine hydraulic characteristics of the system, and (2) to evaluate the movement of runoff pollutants through the system. For the 180 mm/24 h rainfall, the bi-phasic bioretention system effectively reduced both peak flow (approximately 70%) and runoff volume (approximately 42%). The breakthrough curves (BTCs) of bromide tracer suggest that the transport pattern of the system is similar to dispersed plug flow under this large runoff event. The BTCs of bromide showed mean 10% and 90% breakthrough times of 5.7 h and 12.5 h, respectively. Under the continuous rainfall, a significantly different transport pattern was found between each runoff pollutant. Nitrate-N was easily transported through the system with potential leaching risk from the initial soil medium, whereas phosphate-P and metals were significantly retained indicating sorption-mediated transport. These findings support the importance of hydraulics, in combination with the soil medium, when creating bioretention systems for bioremediation that are effective for various rainfall sizes and intervals.

  8. Kinetic resolution of racemic styrene oxide at a high concentration by recombinant Aspergillus usamii epoxide hydrolase in an n-hexanol/buffer biphasic system.

    Science.gov (United States)

    Hu, Die; Wang, Rui; Shi, Xiao-Ling; Ye, Hui-Hua; Wu, Qin; Wu, Min-Chen; Chu, Jian-Jun

    2016-10-20

    Using the cell-free extract of engineered E. coli/Aueh2, expressing the recombinant Aspergillus usamii epoxide hydrolase (reAuEH2), as a biocatalyst, the kinetic resolution technique of racemic styrene oxide (rac-SO) was examined. In a phosphate buffer system (50mM, pH 7.0), 200mM rac-SO was efficiently resolved, obtaining (S)-SO with 98.1% enantiomeric excess (e.e.), whereas (S)-SO only with 45.2% e.e. was obtained from 750mM rac-SO. The analytical results verified that reAuEH2 shows tolerance towards high substrate concentration but is inactivated at a product concentration of 300mM. To produce (S)-SO with the high concentration, e.e. and volumetric productivity, n-hexanol was selected from a variety of water-miscible and water-immiscible organic solvents to construct an n-hexanol/buffer biphasic system. The optimal phase volume ratio, substrate over enzyme ratio and temperature were 1:1 (v/v), 6:1 (w/w) and 25°C, respectively. In an optimized biocatalytic system, a gram-scale resolution of rac-SO at a high concentration of 1M (120g/L) was performed at 25°C for 2h, obtaining (S)-SO with 98.2% e.e., 34.3% yield (maximum yield of 50%). The substrate concentration and volumetric productivity (1M, 20.6g/L/h) in a biphasic system significantly increased compared with those (0.2M, 3.1g/L/h) in a phosphate buffer system. The efficient resolution of rac-SO at a high concentration in a biphasic system makes it a promising technique for preparing a highly value-added enantiopure (S)-SO with high volumetric productivity. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Improved levulinic acid production from agri-residue biomass in biphasic solvent system through synergistic catalytic effect of acid and products.

    Science.gov (United States)

    Kumar, Sandeep; Ahluwalia, Vivek; Kundu, Pranati; Sangwan, Rajender S; Kansal, Sushil K; Runge, Troy M; Elumalai, Sasikumar

    2018-03-01

    In this study, levulinic acid (LA) was produced from rice straw biomass in co-solvent biphasic reactor system consisting of hydrochloric acid and dichloromethane organic solvent. The modified protocol achieved a 15% wt LA yield through the synergistic effect of acid and acidic products (auto-catalysis) and the designed system allowed facile recovery of LA to the organic phase. Further purification of the resulting extractant was achieved through traditional column chromatography, which yielded a high purity LA product while recovering ∼85% wt. Upon charcoal treatment of the resultant fraction generated an industrial grade target molecule of ∼99% purity with ∼95% wt recovery. The system allows the solvent to be easily recovered, in excess of 90%, which was shown to be able to be recycled up to 5 runs without significant loss of final product concentrations. Overall, this system points to a method to significantly reduce manufacturing cost during large-scale LA preparation. Copyright © 2017 Elsevier Ltd. All rights reserved.

  10. Partition of lead in milk-pectin aqueous biphasic system with complexation agents

    International Nuclear Information System (INIS)

    Bartos, P.; Macasek, F.; Gerhart, P.

    1997-01-01

    In present work, decontamination of raw cow milk from lead was investigated using the 'membraneless dialysis'. The 4% w/w solutions of apple pectin, degree of esterification 70%, containing various complexing agents were used for experiments at the initial volume ration pectin : milk = 3:7 which changed to 8:2 at equilibration. Radioactive indicator 212 Pb was prepared from 228 Th emanator. After dissolution in Jennes-Koops buffer with 10 -5 M Pb 2+ carrier, milk was spiked with the indicator for 100 minutes. Distribution equilibrium of water and lead was achieved after next 100 minutes but yield of lead extraction into pectin phase was less then 2.3% in the case of raw milk, and less then 3.0% in the case of pasteurized milk. Due to denaturation of raw milk, there are strongly limited possibilities to influence the radionuclide partition in the systems. Various non-toxic complexation agents (glycine, alanine, histidine, cysteine, Edtacal) were applied to improve extraction of lead to pectin phase. Glycine and histidine have not influence on lead extraction yields but there was observed an increased yield, 3,8% for alanine and even 25% for 0.002 M cysteine. As the most interesting appeared application of Edtacal, calcium salt of ethylenediaminetetraacetic acid, EDTA by which the recovery of lead with with pectin phase reached about 80% at concentration of EDTA in initial pectin phase 0.001 M. The retention of Pb 2+ cation in milk phase is extraordinary high as compared with strontium and corresponds to behavior of trivalent ions what is attributed to specific interactions with thiol groups of milk components

  11. Kinetic studies on the transesterification of sunflower oil with 1-butanol catalyzed by Rhizomucor miehei lipase in a biphasic aqueous-organic system

    NARCIS (Netherlands)

    Ilmi, Miftahul; Hommes, Arne; Winkelman, Jozef; Hidayat, C.; Heeres, Hero

    2016-01-01

    The kinetics of sunflower oil transesterification with 1-butanol using a homogeneous lipase (Rhizomucor miehei) in an aqueous-organic biphasic system were studied in a stirred batch reactor set-up. An initial screening study was performed to optimize relevant process conditions (enzyme

  12. SPS extraction systems

    CERN Multimedia

    CERN PhotoLab

    1973-01-01

    One of the 3-m long electrostatics septa. The septum itself consists of 0.15 mm thick molybdenum wires with a 1.5 mm pitch. Each of the two SPS extraction systems will contain four of these electrostatic septa.

  13. Alternative (Potentially Green) Separations Media: Aqueous Biphasic and Related Systems Extending the Frontier Final Report For Period September 1, 2002 January 31, 2007

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, Robin D

    2007-06-25

    Through the current DoE-BES funding, we have extended our fundamental understanding of the critical phase separation of aqueous polymer solutions at the molecular level, and have developed a similar understanding of their application as novel solvent systems. Our principal aims included mode of delivery of the aqueous biphasic system (ABS) solvent system and the application of this system to problems of reactive extraction. In the former case we have developed novel solid phase analogues, in the form of cross-linked polyethylene glycol hydrogels, and in the latter case we have examined the role that ABS might play in reaction engineering, with a view to greener, simpler, and safer processes. We have also developed a new salt/salt ABS and have extended our understanding of this system as well. The major outcomes are as follows: (1) Through the use of variable temperature phase diagrams, coupled with differential scanning calorimetry (DSC) measurements of the phases, a better understanding of the thermodynamics of phase formation was obtained. Evidence to the existence and role of an upper critical solution temperature (UCST) or lower critical solution temperature (LCST) (or both) in these systems was gained. With variable temperature solute partitioning, thermodynamic parameters were calculated, and inter-system comparisons were made. Through the use of Abraham's linear solvation energy regression (LSER) the solvent-solute properties of liquid/liquid ABS were examined. We have shown that ABS are indeed very tunable and LSERs have been used as a tool to compare these systems to traditional organic/water and other liquid/liquid systems. (2) We have successfully shown the development of novel reaction media for chemical synthesis and reaction; Aqueous Biphasic Reactive Extraction (ABRE). As a proof of concept, we have shown the synthesis of adipic acid from cyclohexene in an ABS, which represents an important development in the exploitation of this technology

  14. Surface chemistry and catalytic properties of VO{sub X}/Ti-MCM-41 catalysts for dibenzothiophene oxidation in a biphasic system

    Energy Technology Data Exchange (ETDEWEB)

    González, J. [ESIQIE, Instituto Politécnico Nacional, Av. Instituto Politécnico Nacional s/n, 07738 Col. Zacatenco, Mexico City (Mexico); Chen, L.F., E-mail: lchen@ipn.mx [ESIQIE, Instituto Politécnico Nacional, Av. Instituto Politécnico Nacional s/n, 07738 Col. Zacatenco, Mexico City (Mexico); Wang, J.A.; Manríquez, Ma.; Limas, R. [ESIQIE, Instituto Politécnico Nacional, Av. Instituto Politécnico Nacional s/n, 07738 Col. Zacatenco, Mexico City (Mexico); Schachat, P.; Navarrete, J. [Dirección de Investigación, Instituto Mexicano del Petróleo, Eje Lázaro Cárdenas 152, 07730 México D.F. (Mexico); Contreras, J.L. [Laboratorio de Catálisis y Polímeros, División de Ciencias Básicas e Ingeniería, Universidad Autónoma Metropolitana-A, Av. San Pablo No. 180, 02200 México D.F. (Mexico)

    2016-08-30

    Highlights: • Oxidative desulfurization of model diesel was tested in a biphasic system. • ODS activity was proportional to the V{sup 5+}/(V{sup 4+} + V{sup 5+}) values of the catalysts. • Lewis acidity was related to vanadium content and catalytic activity. • 99.9% DBT was oxidized using 25%V{sub 2}O{sub 5}/Ti-MCM-41 at 60 °C within 60 min. - Abstract: A series of vanadium oxide supported on Ti-MCM-41 catalysts was synthesized via the incipient impregnation method by varying the vanadia loading from 5 wt% to 10, 15, 20 and 25 wt%. These catalysts were characterized by a variety of advanced techniques for investigating their crystalline structure, textural properties, and surface chemistry information including surface acidity, reducibility, vanadium oxidation states, and morphological features. The catalytic activities of the catalysts were evaluated in a biphasic reaction system for oxidative desulfurization (ODS) of a model diesel containing 300 ppm of dibenzothiophene (DBT) where acetonitrile was used as extraction solvent and H{sub 2}O{sub 2} as oxidant. ODS activity was found to be proportional to the V{sup 5+}/(V{sup 4+} + V{sup 5+}) values of the catalysts, indicating that the surface vanadium pentoxide (V{sub 2}O{sub 5}) was the active phase. Reaction temperature would influence significantly the ODS efficiency; high temperature, i.e., 80 °C, would lead to low ODS reaction due to the partial decomposition of oxidant. All the catalysts contained both Lewis and Brønsted acid sites but the former was predominant. The catalysts with low vanadia loading (5 or 10 wt%V{sub 2}O{sub 5}) had many Lewis acid sites and could strongly adsorb DBT molecule via the electron donation/acceptance action which resulted in an inhibition for the reaction of DBT with the surface peroxometallic species. The catalyst with high vanadia loading (25wt%V{sub 2}O{sub 5}/Ti-MCM-41) showed the highest catalytic activity and could remove 99.9% of DBT at 60 °C within 60 min.

  15. Dual lifetime referencing enables pH-control for oxidoreductions in hydrogel-stabilized biphasic reaction systems.

    Science.gov (United States)

    Begemann, Jens; Spiess, Antje C

    2015-09-01

    pH-shifts are a serious challenge in cofactor dependent biocatalytic oxidoreductions. Therefore, a pH control strategy was developed for reaction systems, where the pH value is not directly measurable. Such a reaction system is the biphasic aqueous-organic reaction system, where the oxidoreduction of hydrophobic substrates in organic solvents is catalysed by hydrogel-immobilized enzymes, and enzyme-coupled cofactor regeneration is accomplished via formate dehydrogenase, leading to a pH-shift. Dual lifetime referencing (DLR), a fluorescence spectroscopic method, was applied for online-monitoring of the pH-value within the immobilizates during the reaction, allowing for a controlled dosage of formic acid. It could be shown that by applying trisodium 8-hydroxypyrene-1, 3, 6-trisulfonate as pH indicator and Ru(II) tris(4, 7-diphenyl-1, 10-phenantroline) (Ru[dpp]) as a reference luminophore the control of the pH-value in a macroscopic gel-bead-stabilized aqueous/organic two phase system in a range of pH 6.5 to 8.0 is possible. An experimental proof of concept could maintain a stable pH of 7.5 ± 0.15 during the reaction for at least 105 h. With these results, it could be shown that DLR is a powerful tool for pH-control within reaction systems with no direct access for conventional pH-measurement. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. User's manual of BISHOP. A Bi-Phase, Sodium-Hydrogen-Oxygen system, chemical equilibrium calculation program

    International Nuclear Information System (INIS)

    Okano, Yasushi; Yamaguchi, Akira

    2001-07-01

    In an event of sodium leakage in liquid metal fast breeder reactors, liquid sodium flows out of piping, and droplet combustion might occur under a certain environmental condition. The combustion heat and reaction products should be evaluated in the sodium fire analysis codes for investigating the influence of the sodium leak age and fire incident. In order to analyze the reaction heat and products, the multi-phase chemical equilibrium calculation program for a sodium, oxygen and hydrogen system has been developed. The developed numerical program is named BISHOP, which denotes 'Bi-Phase, Sodium-Hydrogen-Oxygen, Chemical Equilibrium Calculation Program'. The Gibbs free energy minimization method is used because of the following advantages. Chemical species are easily added and changed. A variety of thermodynamic states, such as isothermal and isentropic changes, can be dealt with in addition to constant temperature and pressure processes. In applying the free energy minimization method to solve the multi-phase sodium reaction system, three new numerical calculation techniques are developed. One is theoretical simplification of phase description in equation system, the other is to extend the Gibbs free energy minimization method to a multi-phase system, and the last is to establish the efficient search for the minimum value. The reaction heat and products at the equilibrium state can be evaluated from the initial conditions, such as temperature, pressure and reactants, using BISHOP. This report describes the thermochemical basis of chemical equilibrium calculations, the system of equations, simplification models, and the procedure to prepare input data and usage of BISHOP. (author)

  17. Aqueous Biphasic Systems for the Synthesis of Formates by Catalytic CO2 Hydrogenation: Integrated Reaction and Catalyst Separation for CO2‐Scrubbing Solutions

    Science.gov (United States)

    Scott, Martin; Blas Molinos, Beatriz; Westhues, Christian

    2017-01-01

    Abstract Aqueous biphasic systems were investigated for the production of formate–amine adducts by metal‐catalyzed CO2 hydrogenation, including typical scrubbing solutions as feedstocks. Different hydrophobic organic solvents and ionic liquids could be employed as the stationary phase for cis‐[Ru(dppm)2Cl2] (dppm=bis‐diphenylphosphinomethane) as prototypical catalyst without any modification or tagging of the complex. The amines were found to partition between the two phases depending on their structure, whereas the formate–amine adducts were nearly quantitatively extracted into the aqueous phase, providing a favorable phase behavior for the envisaged integrated reaction/separation sequence. The solvent pair of methyl isobutyl carbinol (MIBC) and water led to the most practical and productive system and repeated use of the catalyst phase was demonstrated. The highest single batch activity with a TOFav of approximately 35 000 h−1 and an initial TOF of approximately 180 000 h−1 was achieved in the presence of NEt3. Owing to higher stability, the highest productivities were obtained with methyl diethanolamine (Aminosol CST 115) and monoethanolamine (MEA), which are used in commercial scale CO2‐scrubbing processes. Saturated aqueous solutions (CO2 overpressure 5–10 bar) of MEA could be converted into the corresponding formate adducts with average turnover frequencies up to 14×103 h−1 with an overall yield of 70 % based on the amine, corresponding to a total turnover number of 150 000 over eleven recycling experiments. This opens the possibility for integrated approaches to carbon capture and utilization. PMID:28103428

  18. Aqueous Biphasic Systems for the Synthesis of Formates by Catalytic CO2Hydrogenation: Integrated Reaction and Catalyst Separation for CO2-Scrubbing Solutions.

    Science.gov (United States)

    Scott, Martin; Blas Molinos, Beatriz; Westhues, Christian; Franciò, Giancarlo; Leitner, Walter

    2017-03-22

    Aqueous biphasic systems were investigated for the production of formate-amine adducts by metal-catalyzed CO 2 hydrogenation, including typical scrubbing solutions as feedstocks. Different hydrophobic organic solvents and ionic liquids could be employed as the stationary phase for cis-[Ru(dppm) 2 Cl 2 ] (dppm=bis-diphenylphosphinomethane) as prototypical catalyst without any modification or tagging of the complex. The amines were found to partition between the two phases depending on their structure, whereas the formate-amine adducts were nearly quantitatively extracted into the aqueous phase, providing a favorable phase behavior for the envisaged integrated reaction/separation sequence. The solvent pair of methyl isobutyl carbinol (MIBC) and water led to the most practical and productive system and repeated use of the catalyst phase was demonstrated. The highest single batch activity with a TOF av of approximately 35 000 h -1 and an initial TOF of approximately 180 000 h -1 was achieved in the presence of NEt 3 . Owing to higher stability, the highest productivities were obtained with methyl diethanolamine (Aminosol CST 115) and monoethanolamine (MEA), which are used in commercial scale CO 2 -scrubbing processes. Saturated aqueous solutions (CO 2 overpressure 5-10 bar) of MEA could be converted into the corresponding formate adducts with average turnover frequencies up to 14×10 3  h -1 with an overall yield of 70 % based on the amine, corresponding to a total turnover number of 150 000 over eleven recycling experiments. This opens the possibility for integrated approaches to carbon capture and utilization. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

  19. Role of apparent pKa of carboxylic acids in lipase-catalyzed esterifications in biphasic systems

    NARCIS (Netherlands)

    Dominguez de Maria, Pablo; Fernandez-Alvaro, Elena; ten Kate, Antoon; Bargeman, Gerrald

    2009-01-01

    Lipase-catalyzed esterifications in biphasic media (heptane–water, 1:1) were conducted by using Thermomyces lanuginosus lipase (TLL) as biocatalyst. Different carboxylic acids (from acetic to lauric) were thus esterified with 1-butanol at different pH values (2–10). For all carboxylic acids tested,

  20. The Biphasic Effect of Vitamin D on the Musculoskeletal and Cardiovascular System

    Science.gov (United States)

    2017-01-01

    This narrative review summarizes beneficial and harmful vitamin D effects on the musculoskeletal and cardiovascular system. Special attention is paid to the dose-response relationship of vitamin D with clinical outcomes. In infants and adults, the risk of musculoskeletal diseases is highest at circulating 25-hydroxyvitamin D (25OHD) concentrations below 25 nmol/L and is low if 40–60 nmol/L are achieved. However, evidence is also accumulating that in elderly people the risk of falls and fractures increases again at circulating 25OHD levels > 100 nmol/L. Cohort studies report a progressive increase in cardiovascular disease (CVD) events at 25OHD levels  100 nmol/L, but the threshold may be influenced by the level of physical activity. In conclusion, dose-response relationships indicate deleterious effects on the musculoskeletal system and probably on the cardiovascular system at circulating 25OHD levels 100 nmol/L. Future studies should focus on populations with 25OHD levels  100 nmol/L. PMID:28912809

  1. Production of Beauveria bassiana Air Conidia by Means of Optimization of Biphasic System Technology

    Directory of Open Access Journals (Sweden)

    Vladimir Gouli

    2014-08-01

    Full Text Available Air conidia production of Beauveria bassiana, strain CA-603 was studied based on modified diphasic system. The biomass yield obtained in the first phase based on submerged cultivation of fungus was processed using methodology providing different contact with air space. Our study indicated that productivity of the second stage of diphasic system is had inversely proportional dependence on depth of liquid fungal biomass. Increase of biomass depth is significantly decreased production of air conidia. Two methodology of biomass processing extending contact biomass with air space including distribution of fungal material on surface of hygroscopic paper and starch packaging peanuts were investigated. The novel substrates provided optimal contact between the submerged fungal biomass and the air, and overall, conidial production was directly proportional to the total area of air-to-fungal surface. Technologies based on the starch peanuts and hygroscopic paper were the most productive in comparison to the common technology where the submerged culture was transferred to flat containers. The advantages and disadvantages of these different production methods are discussed.

  2. Extraction systems of the SPS

    CERN Multimedia

    CERN PhotoLab

    1973-01-01

    A pair of prototype septum magnets for the extraction systems of the SPS. Each of the two extraction systems will contain eighteen of these septum magnets (eight with a 4 mm septum and ten with a 16 mm septum) mounted in pairs in nine vacuum tanks.

  3. Significant enhancement of (R)-mandelic acid production by relieving substrate inhibition of recombinant nitrilase in toluene-water biphasic system.

    Science.gov (United States)

    Zhang, Zhi-Jun; Pan, Jiang; Liu, Jun-Feng; Xu, Jian-He; He, Yu-Cai; Liu, You-Yan

    2011-03-10

    The enantioselective hydrolysis of mandelonitrile with whole cells of a recombinant Escherichia coli expressing nitrilase activity was severely inhibited by the substrate at high concentrations (>300mM), which resulted in a low yield of the target product (R)-(-)-mandelic acid. To relieve the substrate inhibition and to enhance the (R)-(-)-mandelic acid productivity, eight water-organic solvent biphasic systems were attempted in this work. Toluene was found to be the most suitable solvent as the organic phase among the solvents tested. Various parameters were systematically examined and optimized in shake flasks. The phase volume ratio, buffer pH and reaction temperature were shown to be sensitive parameters affecting both the yield and the enantiopurity of product in the biphasic system. Under the optimized conditions, significant enhancement of substrate tolerance from 200mM to 500mM and average productivity from 179.6gl(-1)d(-1) to 352.6gl(-1)d(-1) were achieved. Subsequently, the biocatalytic hydrolysis of mandelonitrile was successfully carried out in a stirred reactor (2-l scale) by repeated use of the calcium alginate entrapped cells for 5 batches, affording 110.7g (R)-(-)-mandelic acid in 98.0% ee (enantiomeric excess) and a specific production of 13.8g (mandelic acid) g(-1) (cell), respectively. Copyright © 2011 Elsevier B.V. All rights reserved.

  4. Expression of matrix metalloproteinases and components of the endocannabinoid system in the knee joint are associated with biphasic pain progression in a rat model of osteoarthritis

    Directory of Open Access Journals (Sweden)

    Pajak A

    2017-08-01

    Full Text Available Agnieszka Pajak, Magdalena Kostrzewa, Natalia Malek, Michal Korostynski, Katarzyna Starowicz Institute of Pharmacology, Polish Academy of Sciences, Krakow, Poland Abstract: Matrix metalloproteinases (MMPs are considered important in articular cartilage breakdown during osteoarthritis (OA. Similarly, the endocannabinoid system (ECS is implicated in joint function and modulation of nociceptive processing. Functional interplay between ECS and MMPs has been recently indicated. Here, we tested if changes in the expression of selected MMPs and major ECS elements temporally correlate with the intensity of OA-related pain. Knee OA was induced in male Wistar rats by intra-articular sodium monoiodoacetate injection. OA-like pain behavior was tested using the dynamic weight bearing. Joint tissue samples at different time points after OA induction were subjected to gene (quantitative polymerase chain reaction and protein (Western blot expression analyses. Monoiodoacetate-induced nocifensive responses in rats showed a biphasic progression pattern. The alterations in expression of selected MMPs elegantly corresponded to the two-stage development of OA pain. The most substantial changes in the expression of the ECS system were revealed at a later stage of OA progression. Alterations within ECS are involved in the process of adaptation to persistent painful stimuli. The accumulation of MMPs in osteoarthritic cartilage may have a role in the biphasic progression of OA-related pain. Temporal association of changes in ECS and MMPs expression shows a potential therapeutic approach that utilizes the concept of combining indirect ECS-mediated MMP inhibition and ECS modulation of pain transduction. Keywords: osteoarthritis, monoiodoacetate, pain, matrix metalloproteinases, endocannabinoid system

  5. In vitro study on biomineralization of biphasic calcium phosphate ...

    Indian Academy of Sciences (India)

    Abstract. In this study, we report the preparation of a bone graft material, having cylindrical shape, containing biphasic calcium phosphate (BCP), gelatin (G), chitosan (C) and Terminalia chebula (TC) extract. TC extract was used as a crosslinker that gives stability to bone graft when it is placed in SBF. The graft was stable in ...

  6. In vitro study on biomineralization of biphasic calcium phosphate ...

    Indian Academy of Sciences (India)

    In this study, we report the preparation of a bone graft material, having cylindrical shape, containing biphasic calcium phosphate (BCP), gelatin (G), chitosan (C) and Terminalia chebula (TC) extract. TC extract was used as a crosslinker that gives stability to bone graft when it is placed in SBF. The graft was stable in the SBF ...

  7. New AGS fast extraction system

    International Nuclear Information System (INIS)

    Weng, W.T.

    1980-09-01

    Both the high energy physics program and ISA injection require an improved fast extraction system from the AGS. The proposed new system consists of a fast kicker at H5 and an ejector magnet at H10. The H5 kicker is capable of producing 1.2 mrad deflection and rising up to 99% strength in 150 nsec with flat top ripple within +- 1%. It is found that the focusing strengths and positions of UQ3-UQ7 have to be modified to achieve an achromatic condition at the end of 8 0 -bend. Also, the conceptual design of the H5 magnet and the pulser system are discussed

  8. DESIGNING AN EVENT EXTRACTION SYSTEM

    Directory of Open Access Journals (Sweden)

    Botond BENEDEK

    2017-06-01

    Full Text Available In the Internet world, the amount of information available reaches very high quotas. In order to find specific information, some tools were created that automatically scroll through the existing web pages and update their databases with the latest information on the Internet. In order to systematize the search and achieve a result in a concrete form, another step is needed for processing the information returned by the search engine and generating the response in a more organized form. Centralizing events of a certain type is useful first of all for creating a news service. Through this system we are pursuing a knowledge - events from the Internet documents - extraction system. The system will recognize events of a certain type (weather, sports, politics, text data mining, etc. depending on how it will be trained (the concept it has in the dictionary. These events can be provided to the user, or it can also extract the context in which the event occurred, to indicate the initial form in which the event was embedded.

  9. Ligand modification for mono- and biphasic oxosynthesis

    Energy Technology Data Exchange (ETDEWEB)

    Haerter, P.; Herrmann, W.A.; Baskakov, D. [Technische Univ. Muenchen (Germany). Dept. Chemie

    2006-07-01

    The use of aqueous/organic biphasic systems has attracted huge interest in catalytic reactions by transition metal complexes. [1,2,3] The biphasic systems have benefits in catalyst separation and recycling, and the reduction or elimination of organic solvents is also advantageous for the development of economical and environmentally friendly processes. The key for such biphasic catalysis is the use of water soluble phosphines as ligands. Since the launch of the commercial propylene hydroformylation process by Ruhrchemie/Rhone-Poulenc, sulfonated ligands such as TPPTS (1), and BINAS (2) have been widely used as ligands in hydroformylation, hydrogenation and related reactions catalyzed by transition metals. One of the draw backs of ligands 1 and 2 are corrosive production conditions and therefore unfavorable costs. With the synthesis of aminoacid based trishydroxymethylphosphine derivatives (THMP-aminoacid) we introduce to our knowledge a new group of water soluble and cheap to produce ligands [8]. The properties of catalysts based on these compounds in the hydroformylation reaction of propene are discussed in comparison to normally used catalyst systems. In a second part the performance of catalysts containing NHC-ligands in the hydroformylation of 1-octene is discussed [9]. These investigations show, that the activity can be influenced by the electron donating ability of the NHC ligand. Sterical variations on the NHC ligands have no effect on the selectivity performance of the the catalysts. (orig.)

  10. Sonolytic and Silent Polymerization of Methacrlyic Acid Butyl Ester Catalyzed by a New Onium Salt with bis-Active Sites in a Biphasic System — A Comparative Investigation

    Directory of Open Access Journals (Sweden)

    Perumberkandgai A. Vivekanand

    2013-02-01

    Full Text Available Currently, ingenious new analytical and process experimental techniques which are environmentally benign techniques, viz., ultrasound irradiation, have become immensely popular in promoting various reactions. In this work, a novel soluble multi-site phase transfer catalyst (PTC viz., 1,4-bis-(propylmethyleneammounium chloridebenzene (BPMACB was synthesized and its catalytic efficiency was assessed by observing the kinetics of sonolytic polymerization of methacrylic acid butyl ester (MABE using potassium persulphate (PPS as an initiator. The ultrasound–multi-site phase transfer catalysis (US-MPTC-assisted polymerization reaction was compared with the silent (non-ultrasonic polymerization reaction. The effects of the catalyst and various reaction parameters on the catalytic performance were in detail investigated by following the kinetics of polymerization of MABE in an ethyl acetate-water biphasic system. From the detailed kinetic investigation we propose a plausible mechanism. Further the kinetic results demonstrate clearly that ultrasound-assisted phase-transfer catalysis significantly increased the reaction rate when compared to silent reactions. Notably, this environmentally benign and cost-effective process has great potential to be applied in various polymer industries.

  11. Acute Biphasic Effects of Ayahuasca.

    Science.gov (United States)

    Schenberg, Eduardo Ekman; Alexandre, João Felipe Morel; Filev, Renato; Cravo, Andre Mascioli; Sato, João Ricardo; Muthukumaraswamy, Suresh D; Yonamine, Maurício; Waguespack, Marian; Lomnicka, Izabela; Barker, Steven A; da Silveira, Dartiu Xavier

    2015-01-01

    Ritual use of ayahuasca, an amazonian Amerindian medicine turned sacrament in syncretic religions in Brazil, is rapidly growing around the world. Because of this internationalization, a comprehensive understanding of the pharmacological mechanisms of action of the brew and the neural correlates of the modified states of consciousness it induces is important. Employing a combination of electroencephalogram (EEG) recordings and quantification of ayahuasca's compounds and their metabolites in the systemic circulation we found ayahuasca to induce a biphasic effect in the brain. This effect was composed of reduced power in the alpha band (8-13 Hz) after 50 minutes from ingestion of the brew and increased slow- and fast-gamma power (30-50 and 50-100 Hz, respectively) between 75 and 125 minutes. Alpha power reductions were mostly located at left parieto-occipital cortex, slow-gamma power increase was observed at left centro-parieto-occipital, left fronto-temporal and right frontal cortices while fast-gamma increases were significant at left centro-parieto-occipital, left fronto-temporal, right frontal and right parieto-occipital cortices. These effects were significantly associated with circulating levels of ayahuasca's chemical compounds, mostly N,N-dimethyltryptamine (DMT), harmine, harmaline and tetrahydroharmine and some of their metabolites. An interpretation based on a cognitive and emotional framework relevant to the ritual use of ayahuasca, as well as it's potential therapeutic effects is offered.

  12. Acute Biphasic Effects of Ayahuasca.

    Directory of Open Access Journals (Sweden)

    Eduardo Ekman Schenberg

    Full Text Available Ritual use of ayahuasca, an amazonian Amerindian medicine turned sacrament in syncretic religions in Brazil, is rapidly growing around the world. Because of this internationalization, a comprehensive understanding of the pharmacological mechanisms of action of the brew and the neural correlates of the modified states of consciousness it induces is important. Employing a combination of electroencephalogram (EEG recordings and quantification of ayahuasca's compounds and their metabolites in the systemic circulation we found ayahuasca to induce a biphasic effect in the brain. This effect was composed of reduced power in the alpha band (8-13 Hz after 50 minutes from ingestion of the brew and increased slow- and fast-gamma power (30-50 and 50-100 Hz, respectively between 75 and 125 minutes. Alpha power reductions were mostly located at left parieto-occipital cortex, slow-gamma power increase was observed at left centro-parieto-occipital, left fronto-temporal and right frontal cortices while fast-gamma increases were significant at left centro-parieto-occipital, left fronto-temporal, right frontal and right parieto-occipital cortices. These effects were significantly associated with circulating levels of ayahuasca's chemical compounds, mostly N,N-dimethyltryptamine (DMT, harmine, harmaline and tetrahydroharmine and some of their metabolites. An interpretation based on a cognitive and emotional framework relevant to the ritual use of ayahuasca, as well as it's potential therapeutic effects is offered.

  13. Odd-even effect on the formation of aqueous biphasic systems formed by 1-alkyl-3-methylimidazolium chloride ionic liquids and salts

    Science.gov (United States)

    Belchior, Diana C. V.; Sintra, Tânia E.; Carvalho, Pedro J.; Soromenho, Mário R. C.; Esperança, José M. S. S.; Ventura, Sónia P. M.; Rogers, Robin D.; Coutinho, João A. P.; Freire, Mara G.

    2018-05-01

    This work provides a comprehensive evaluation of the effect of the cation alkyl side chain length of the 1-alkyl-3-methylimidazolium chloride series ([CnC1im]Cl, n = 2-14) of ionic liquids (ILs) on their capability to form aqueous biphasic systems (ABSs) with salts and self-aggregation derived properties. The liquid-liquid phase behavior of ternary systems composed of [CnC1im]Cl, water, and K3PO4 or K2CO3 and the respective Setschenow salting-out coefficients (ks), a quantitative measure of the two-phase formation ability, were determined. An odd-even effect in the ks values along the number of methylene groups of the longest IL cation alkyl side chain was identified for the ABS formed by K2CO3, a weaker salting-out agent where the phenomenon is clearly identified. In general, cations with even alkyl side chains, being likely to display higher molar volumes, are more easily salted-out and thus more prone to undergo phase separation. The odd-even effect in the ks values is, however, more significant in ILs up to n = 6, where the nanostructuration/nanosegregation of ILs plays a less relevant role. Still, with the [CnC1im]Cl (n = 7-14) series of ILs, an odd-even effect was also identified in the ILs' ionization degree, molar conductivity, and conductivity at infinite dilution. In summary, it is shown here that the ILs' odd-even effect occurs in IL aqueous solutions and not just in neat ILs, an already well-established phenomenon occurring in a series of ILs' properties described as a result of the orientation of the terminal methyl groups to the imidazolium ring cation and consequent effect in the ILs' cohesive energy.

  14. Primary intrathoracic biphasic synovial sarcoma.

    Science.gov (United States)

    Tezcan, Yilmaz; Koc, Mehmet; Kocak, Husnu; Kaya, Yusuf

    2012-05-01

    Synovial sarcomas are most frequently observed in the extremities. Although synovial sarcomas are the third most common histological type of soft-tissue sarcomas of the extremities, primary mediastinal synovial sarcoma is extremely rare. Monophasic synovial sarcoma is the most commonly observed subtype. whereas the biphasic subtype is less common. We present our case which was diagnosed as biphasic synovial sarcoma located in the anterior mediastinum, which is considered to be a rare entity. The patient underwent surgical resection together with multimodal adjuvant radiotherapy and chemotherapy.

  15. Irradiation of Oil / Water Biphasic Systems: the Importance of Interfacial Surface Area on the Production of Hydrogen and Other Deleterious Products

    International Nuclear Information System (INIS)

    Causey, Patrick-W.; Stuart, Craig-R.

    2012-09-01

    -water interfacial surface area, control of headspace gas composition, and removal of sample aliquots. Results highlight the importance of interfacial surface area in affecting the radiolytic degradation of the studied hydrocarbons. In particular, experiments having higher oil-water interfacial surface areas generate greater quantities of oil degradation products as compared with lower surface area samples. As expected, one notable result from these irradiations was the formation of significant quantities of hydrogen, which was found to be dependent on the interfacial surface area. Presented here is a review of the radiolytic degradation of insoluble organic material in aqueous systems, a summary of experimental results focusing on biphasic systems and a description of a strategy to mitigate the effects of insoluble organic material ingress and to aid in developing station-appropriate responses. (authors)

  16. Pd(II-dissolved in ionic liquids: a recyclable catalytic system for the selective biphasic hydrogenation of dienes to monoenes

    Directory of Open Access Journals (Sweden)

    Dupont Jairton

    2000-01-01

    Full Text Available Palladium acetylacetonate dissolved in 1-n-butyl-3-methylimidazolium tetrafluoroborate ionic liquid catalyses the selective two-phase hydrogenation of conjugated and non-conjugated (functionalized and non-functionalized dienes into the respective monoenes. The system does not require the use of organic solvents, the products are removed by simple decantation or distillation and the recovered ionic catalytic solution can be reused several times without any significant changes in its catalytic activity and selectivity.

  17. Liquid biphase systems formed in ternary mixtures of two organic solvents and ethylene oxide oligomers or polymers

    Directory of Open Access Journals (Sweden)

    Spitzer Marcos

    2000-01-01

    Full Text Available Phase equilibrium data were determined for ternary systems containing ethylene oxide oligomers or polymers, heptane and one of three organic solvents (methanol, dichloromethane or chloroform. The effects of temperature, of polymer molecular weight and of the chemical nature of the organic solvent on phase equilibrium were investigated. For all the studied systems, the miscibility region was reduced as temperature decreased, indicating an exothermic phase separation process. For both binary and ternary mixtures, the miscibility also decreased as the macromolecule size increased, although this effect was less significant for the ternary mixtures. These features suggest that phase separation is more influenced by enthalpic than entropic contributions. Regarding the different polar solvents investigated, methanol presented a much smaller miscibility region, in accordance with its inferior solvation ability for PEO. The largest miscibility region was observed with chloroform, not much different from the behaviour observed with dichloromethane. Tie lines were determined for some systems, confirming the strong segregation between polymer and the hydrocarbon solvent.

  18. Speciation of native cations and added radionuclides in raw bovine milk. I. membraneless dialysis in aqueous biphasic systems

    International Nuclear Information System (INIS)

    Macasek, F.; Gerhart, P.; Malovikova, A.; Celkova, A.

    1996-01-01

    Partition of native sodium, potassium, magnesium, calcium and radioisotopes of cesium, strontium and europium was investigated in the aqueous liquid-liquid systems formed after agitation of fresh pasteurized skim bovine milk with 4% w/w water solution of pectin of various degree of esterification (60-93%). The partition of the ions in the 'membraneless dialysis' was described by Donnan equilibria and ion-exchange in the macro-and microheterogenous systems and, within uncertainty of results, does not depend on the degree of esterification. Strong negative non-ideality of Sr and Eu in milk phase is attributed to binding with proteins, casein particles in particular, and complexation with low molecular ligands. Separation factor α = D(Sr)/D(Ca) is 0.70 ±0.06, in favor of strontium concentration in pectin phase. While>96% of cesium is diffusible to pectin phase, only 43-56% (depending on physico-chemical model of dialysis) of strontium behaves in that way, and in original milk phase the percent of strontium cationic from may be as low as 13%. (author). 24 refs., 8 figs., 4 tabs

  19. Reactive extraction at liquid-liquid systems

    Science.gov (United States)

    Wieszczycka, Karolina

    2018-01-01

    The chapter summarizes the state of knowledge about a metal transport in two-phase system. The first part of this review focuses on the distribution law and main factors determination in classical solvent extraction (solubility and polarity of the solute, as well as inter- and intramolecules interaction. Next part of the chapter is devoted to the reactive solvent extraction and the molecular modeling requiring knowledge on type of extractants, complexation mechanisms, metals ions speciation and oxidation during complexes forming, and other parameters that enable to understand the extraction process. Also the kinetic data that is needed for proper modeling, simulation and design of processes needed for critical separations are discussed. Extraction at liquid-solid system using solvent impregnated resins is partially identical as in the case of the corresponding solvent extraction, therefore this subject was also presented in all aspects of separation process (equilibrium, mechanism, kinetics).

  20. Biphasic Catalysis with Disaccharide Phosphorylases: Chemoenzymatic Synthesis of alpha-D-Glucosides Using Sucrose Phosphorylase

    Czech Academy of Sciences Publication Activity Database

    De Winter, K.; Desmet, T.; Devlamynck, T.; Van Renterghem, L.; Verhaeghe, T.; Pelantová, Helena; Křen, Vladimír; Soetaert, W.

    2014-01-01

    Roč. 18, č. 6 (2014), s. 781-787 ISSN 1083-6160 R&D Projects: GA MŠk(CZ) 7E11011 Institutional support: RVO:61388971 Keywords : biphasic systems * pyrogallol * biphasic catalysis Subject RIV: CE - Biochemistry Impact factor: 2.528, year: 2014

  1. Production of levulinic acid, furfural, and gamma valerolactone from C.sub.5 and C.sub.6 carbohydrates in mono- and biphasic systems using gamma-valerolactone as a solvent

    Energy Technology Data Exchange (ETDEWEB)

    Dumesic, James A.; Alonso, David Martin; Gurbuz, Elif I.; Wettstein, Stephanie G.

    2013-03-19

    A method to make levulinic acid (LA), furfural, or gamma-valerolactone (GVL). React cellulose (and/or other C.sub.6 carbohydrates) or xylose (and/or other C.sub.5 carbohydrates) or combinations thereof in a monophasic reaction medium comprising GVL and an acid; or (ii) a biphasic reaction system comprising an organic layer comprising GVL, and a substantially immiscible aqueous layer. At least a portion of the cellulose (and/or other C.sub.6 carbohydrates), if present, is converted to LA and at least a portion of the xylose (and/or other C.sub.5 carbohydrates), if present, is converted into furfural.

  2. Statistical feature extraction based iris recognition system

    Indian Academy of Sciences (India)

    Atul Bansal

    Abstract. Iris recognition systems have been proposed by numerous researchers using different feature extraction techniques for accurate and reliable biometric authentication. In this paper, a statistical feature extraction technique based on correlation between adjacent pixels has been proposed and implemented. Ham-.

  3. Effective extraction of cephalosporin C from whole fermentation ...

    African Journals Online (AJOL)

    The biphasic system was prepared by mixing equal aliquots of 15% w/w polyethylene glycol (PEG) 3350 with 15% (NH4)2SO4. The effects of pH, neutral salts, temperature and centrifugal force on partitioning in ATPS to develop efficient extraction system for recovery of CPC from fermentation broth were also examined.

  4. Operation of the tevatron extraction system

    International Nuclear Information System (INIS)

    Finley, D.A.; Harrison, M.; Merz, W.; Pfeffer, H.

    1985-01-01

    The Fermilab Tevatron is currently in the middle of its second running period for fixed target physics. Steady operation has been established at 800 GeV with l X 10 13 protons being extracted. Beam spill over the 20 - 23 second flattop is regulated by a closed loop feedback and a feed forward learning system controlled by a microprocessor. Eight power supplies have their waveforms programmed by the microprocessor in an attempt to reduce the modulation on the beam spill. In addition the microprocessor can insert a pause in the slow spill and cause the extraction of a high intensity (3 X 10 12 ) fast (1-2 milliseconds long) pulse. A description of the extraction system as well as analysis of the spill modulation encountered during commissioning are presented in this paper. Current status of the spill structure is also discussed

  5. Statistical feature extraction based iris recognition system

    Indian Academy of Sciences (India)

    Atul Bansal

    features obtained from one's face [1], finger [2], voice [3] and/or iris [4, 5]. Iris recognition system is widely used in high security areas. A number of researchers have proposed various algorithms for feature extraction. A little work [6,. 7] however, has been reported using statistical techniques directly on pixel values in order to ...

  6. Ionic liquid pre-treatment of microalgae and extraction of biomolecules

    NARCIS (Netherlands)

    Desai, Rupali K.

    2016-01-01

    Liquid-liquid extraction (LLE) techniques are widely used in separation primarily due to ease of scale up. Conventional (LLE) systems based on organic solvents are not suitable for extraction of fragile molecules such as proteins as it would result in denaturation. On the other hand aqueous biphasic

  7. Production, Purification, and Identification of Cholest-4-en-3-one Produced by Cholesterol Oxidase from sp. in Aqueous/Organic Biphasic System

    Directory of Open Access Journals (Sweden)

    Ke Wu

    2015-01-01

    Full Text Available Cholest-4-en-3-one has positive uses against obesity, liver disease, and keratinization. It can be applied in the synthesis of steroid drugs as well. Most related studies are focused on preparation of cholest-4-en-3-one by using whole cells as catalysts, but production of high-quality cholest-4-en-3-one directly from cholesterol oxidase (COD using an aqueous/organic two-phase system has been rarely explored. This study set up an enzymatic reaction system to produce cholest-4-en-3-one. We developed and optimized the enzymatic reaction system using COD from COX5-6 (a strain of Rhodococcus instead of whole-cell biocatalyst. This not only simplifies and accelerates the production but also benefits the subsequent separation and purification process. Through extraction, washing, evaporation, column chromatography, and recrystallization, we got cholest-4-en-3-one with purity of 99.78%, which was identified by nuclear magnetic resonance, mass spectroscopy, and infrared spectroscopy. In addition, this optimized process of cholest-4-en-3-one production and purification can be easily scaled up for industrial production, which can largely decrease the cost and guarantee the purity of the product.

  8. A portable foot-parameter-extracting system

    Science.gov (United States)

    Zhang, MingKai; Liang, Jin; Li, Wenpan; Liu, Shifan

    2016-03-01

    In order to solve the problem of automatic foot measurement in garment customization, a new automatic footparameter- extracting system based on stereo vision, photogrammetry and heterodyne multiple frequency phase shift technology is proposed and implemented. The key technologies applied in the system are studied, including calibration of projector, alignment of point clouds, and foot measurement. Firstly, a new projector calibration algorithm based on plane model has been put forward to get the initial calibration parameters and a feature point detection scheme of calibration board image is developed. Then, an almost perfect match of two clouds is achieved by performing a first alignment using the Sampled Consensus - Initial Alignment algorithm (SAC-IA) and refining the alignment using the Iterative Closest Point algorithm (ICP). Finally, the approaches used for foot-parameterextracting and the system scheme are presented in detail. Experimental results show that the RMS error of the calibration result is 0.03 pixel and the foot parameter extracting experiment shows the feasibility of the extracting algorithm. Compared with the traditional measurement method, the system can be more portable, accurate and robust.

  9. Salting Out Effect of Electrolyte Solutions in The Extraction of ...

    African Journals Online (AJOL)

    USER

    ABSTRACT: The salting-out effect of various solutions of electrolyte in the extraction of tantalum and niobium using aqueous biphasic system (ABS) was investigated. This was achieved by leaching ball-milled Tantalite ore with mineral acids (H2SO4 and HF) in the ratio of 3:1. The leached liquor was then divided into five ...

  10. BUILDING EXTRACTION USING MULTI SENSOR SYSTEMS

    Directory of Open Access Journals (Sweden)

    N. Yastikli

    2013-05-01

    Full Text Available In this study, the automatic building extraction is aimed using object-based image analysis method with multi sensor system includes LiDAR, digital camera and GPS/IMU. The image processing techniques, segmentation and classification methods were used for automatic object extraction with defined rule set. The proposed method based on object based classification to overcome the limitation of traditional pixel based classification such as confusion of classes. The generated Digital Surface Model (DSM from LiDAR point cloud was used to separate building and vegetation classes. The morphologic filters were utilized also optimization of mixed classes. In our proposed approach for building extraction, multi-resolution, contrast-difference and chessboard segmentations were applied. The object-based classification method was preferred in classification process with defined fuzzy rules. First, vegetation and ground classes were generated than building regions were derived with using the results of the classification and segmentation. The data set was obtained from the project of "NABUCCO Gas Pipeline Project". The data set actually was collected for corridor mapping of pipeline which will link the Eastern border of Turkey, to Baumgarten in Austria via Bulgaria, Romania and Hungary. The study area is a suburban neighborhood located in the city of Sivas, Turkey. The Leica ALS60 LiDAR system, DiMAC, Dalsa Area Bayer RGB Charge Coupled (CCD Camera and GPS and CUS6 IMU system were used for data collection. The additional data sets were generated with point cloud collected by LiDAR and RGB images from digital camera. The rule sets for automatic building extraction were developed in Definiens e-Cognition Developer 8.64 program system. To evaluate the performance of proposed automatic building extraction approach, reference data set was generated with digitizing of extracted building over the orthoimage. The accuracy assessment was performed with completeness and

  11. Extracting the information backbone in online system.

    Science.gov (United States)

    Zhang, Qian-Ming; Zeng, An; Shang, Ming-Sheng

    2013-01-01

    Information overload is a serious problem in modern society and many solutions such as recommender system have been proposed to filter out irrelevant information. In the literature, researchers have been mainly dedicated to improving the recommendation performance (accuracy and diversity) of the algorithms while they have overlooked the influence of topology of the online user-object bipartite networks. In this paper, we find that some information provided by the bipartite networks is not only redundant but also misleading. With such "less can be more" feature, we design some algorithms to improve the recommendation performance by eliminating some links from the original networks. Moreover, we propose a hybrid method combining the time-aware and topology-aware link removal algorithms to extract the backbone which contains the essential information for the recommender systems. From the practical point of view, our method can improve the performance and reduce the computational time of the recommendation system, thus improving both of their effectiveness and efficiency.

  12. Transient Behaviour of Interacting Extractive System

    International Nuclear Information System (INIS)

    El-Bialy, S.H.; Elsherbiny, A.E.

    2000-01-01

    The aim of this study is to investigate the dynamic behaviour of mixer-settler extractive system, which represents an interacting one. When a stimulus single is introduced to aqueous feed; the response of the aqueous phase of the first stage is considered as stimulus signals to both organic phase in the same stage and the aqueous phase of the second one. The response of the last phase represents-in turn- stimulus signals to both organic phase in the same stage and the aqueous phase in the next one. Mathematical model was derived for a system consisting of two stages in the cascade. The model assumed a continuous stirred tank reactor (CSTR) for mixer zone and variable holdups and flow rates of both aqueous and organic phases during operation. Non-linear equilibrium was considered. The obtained model-being non-linear- was linearized and Laplace transformation method was used to solve the model. The system constants are those corresponding to extraction of uranyl nitrate from 3 N nitric acid solution using Tbp dissolved in kerosene at 30% of the former. Stimulus-response test was carried out on the model by considering a step increase in solute concentration in aqueous feed stream. The system behaviour was tested at different values of operating parameters. First order behaviour for the first stage was observed and higher order for the rest of the system. A general relation for the difference in the power of the denominator and numerator of the transfer function of the i th stage was concluded for aqueous phase. The study showed that the system overdamp over the practical range of chosen parameters as explained from the values of transfer function roots

  13. Cu(II)-mediated atom transfer radical polymerization of methyl methacrylate via a strategy of thermo-regulated phase-separable catalysis in a liquid/liquid biphasic system: homogeneous catalysis, facile heterogeneous separation, and recycling.

    Science.gov (United States)

    Pan, Jinlong; Zhang, Bingjie; Jiang, Xiaowu; Zhang, Lifen; Cheng, Zhenping; Zhu, Xiulin

    2014-09-01

    A strategy of thermo-regulated phase-separable catalysis (TPSC) is applied to the Cu(II)-mediated atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in a p-xylene/PEG-200 biphasic system. Initiators for continuous activator regeneration ATRP (ICAR ATRP) are used to establish the TPSC-based ICAR ATRP system using water-soluble TPMA as a ligand, EBPA as an initiator, CuBr2 as a catalyst, and AIBN as a reducing agent. By heating to 70 °C, unlimited miscibility of both solvents is achieved and the polymerization can be carried out under homogeneous conditions; then on cooling to 25 °C, the mixture separates into two phases again. As a result, the catalyst complex remains in the PEG-200 phase while the obtained polymers stay in the p-xylene phase. The catalyst can therefore be removed from the resultant polymers by easily separating the two different layers and can be reused again. It is important that well-defined PMMA with a controlled molecular weight and narrow molecular weight distribution could be obtained using this TPSC-based ICAR ATRP system. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Extraction of quantifiable information from complex systems

    CERN Document Server

    Dahmen, Wolfgang; Griebel, Michael; Hackbusch, Wolfgang; Ritter, Klaus; Schneider, Reinhold; Schwab, Christoph; Yserentant, Harry

    2014-01-01

    In April 2007, the  Deutsche Forschungsgemeinschaft (DFG) approved the  Priority Program 1324 “Mathematical Methods for Extracting Quantifiable Information from Complex Systems.” This volume presents a comprehensive overview of the most important results obtained over the course of the program.   Mathematical models of complex systems provide the foundation for further technological developments in science, engineering and computational finance.  Motivated by the trend toward steadily increasing computer power, ever more realistic models have been developed in recent years. These models have also become increasingly complex, and their numerical treatment poses serious challenges.   Recent developments in mathematics suggest that, in the long run, much more powerful numerical solution strategies could be derived if the interconnections between the different fields of research were systematically exploited at a conceptual level. Accordingly, a deeper understanding of the mathematical foundations as w...

  15. Simultaneous extraction and concentration of water pollution tracers using ionic-liquid-based systems.

    Science.gov (United States)

    Dinis, Teresa B V; Passos, Helena; Lima, Diana L D; Sousa, Ana C A; Coutinho, João A P; Esteves, Valdemar I; Freire, Mara G

    2017-07-29

    Human activities are responsible for the release of innumerous substances into the aquatic environment. Some of these substances can be used as pollution tracers to identify contamination sources and to prioritize monitoring and remediation actions. Thus, their identification and quantification are of high priority. However, due to their presence in complex matrices and at significantly low concentrations, a pre-treatment/concentration step is always required. As an alternative to the currently used pre-treatment methods, mainly based on solid-phase extractions, aqueous biphasic systems (ABS) composed of ionic liquids (ILs) and K 3 C 6 H 5 O 7 are here proposed for the simultaneous extraction and concentration of mixtures of two important pollution tracers, caffeine (CAF) and carbamazepine (CBZ). An initial screening of the IL chemical structure was carried out, with extraction efficiencies of both tracers to the IL-rich phase ranging between 95 and 100%, obtained in a single-step. These systems were then optimized in order to simultaneously concentrate CAF and CBZ from water samples followed by HPLC-UV analysis, for which no interferences of the ABS phase-forming components and other interferents present in a wastewater effluent sample have been found. Based on the saturation solubility data of both pollution tracers in the IL-rich phase, the maximum estimated concentration factors of CAF and CBZ are 28595- and 8259-fold. IL-based ABS can be thus envisioned as effective pre-treatment techniques of environmentally-related aqueous samples for a more accurate monitoring of mixtures of pollution tracers. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Data extraction system for underwater particle holography

    Science.gov (United States)

    Nebrensky, J. J.; Craig, Gary; Hobson, Peter R.; Lampitt, R. S.; Nareid, Helge; Pescetto, A.; Trucco, Andrea; Watson, John

    2000-08-01

    Pulsed laser holography in an extremely powerful technique for the study of particle fields as it allows instantaneous, non-invasive high- resolution recording of substantial volumes. By relaying the real image one can obtain the size, shape, position and - if multiple exposures are made - velocity of every object in the recorded field. Manual analysis of large volumes containing thousands of particles is, however, an enormous and time-consuming task, with operator fatigue an unpredictable source of errors. Clearly the value of holographic measurements also depends crucially on the quality of the reconstructed image: not only will poor resolution degrade the size and shape measurements, but aberrations such as coma and astigmatism can change the perceived centroid of a particle, affecting position and velocity measurements. For large-scale applications of particle field holography, specifically the in situ recording of marine plankton with Holocam, we have developed an automated data extraction system that can be readily switched between the in-line and off-axis geometries and provides optimised reconstruction from holograms recorded underwater. As a videocamera is automatically stepped through the 200 by 200 by 1000mm sample volume, image processing and object tracking routines locate and extract particle images for further classification by a separate software module.

  17. Use of Saccharomyces cerevisiae yeasts in the chemo selective bioreduction of (1E,4E)-1,5-bis(4-methoxyphenyl)-1,4-pentadien-3-one in biphasic system

    Energy Technology Data Exchange (ETDEWEB)

    Schaefer, Cesar A.; Silva, Vanessa D.; Nascimento, Maria da G., E-mail: maria.nascimento@ufsc.br [Departamento de Quimica, Universidade Federal de Santa Catarina, Florianopolis-SC (Brazil); Stambuk, Boris U. [Departamento de Bioquimica, Universidade Federal de Santa Catarina, Florianopolis-SC (Brazil)

    2013-07-15

    This work describes the chemoselective bioreduction of (1E,4E)-1,5-bis(4-methoxyphenyl)- 1,4-pentadien-3-one (1) mediated by baker's yeast (BY, Saccharomyces cerevisiae cells) in an aqueous/organic solvent biphasic system. The biotransformation of this compound was chemoselective and formed only the corresponding saturated ketone 1,5-bis(4-methoxyphenyl)- 3-pentanone (2). The influence of various factors which may alter the bioreduction of 1, such as the type and percentage of co-solvents, use of six different S. cerevisiae yeast samples (four commercial and two industrial), variations in the substrate and yeast concentrations, temperature, pH and volume of aqueous and organic phases, was investigated. The best reaction conditions were 66.7 g L{sup -1} of Fleischmann BY, 8.3 Multiplication-Sign 10{sup -3} mol L{sup -1} of substrate, pH 6.5 at 35 deg C in the presence of 2.5% (v/v) of N,N-dimethyl sulfoxide (DMSO) as an additive and a V{sub aq}/V{sub org} ratio of 70/30. Under these conditions, the product 2 was recovered in conversions of 82% in 5 h reaction. (author)

  18. Design of a high current extraction/strypping system using extraction and stripping isotherms

    OpenAIRE

    Danovska, Milena; Karanfilov, Dejan; Golomeova, Mirjana; Krstev, Boris; Zendelska, Afrodita

    2015-01-01

    The isotherms define the capacity of some extragent for its capability to extract required metal (in this case copper). They are used to evaluate how the system extraction/stripping works, or expected to work. The construction of extraction isotherm consists of the following stages: preparation of laboratory extragent, the organic phase is brought into contact with the electrolyte, optimization of the extraction equilibrium isotherm. Similarly, construct and stripping isotherm: or...

  19. Extracting the information backbone in online system.

    Directory of Open Access Journals (Sweden)

    Qian-Ming Zhang

    Full Text Available Information overload is a serious problem in modern society and many solutions such as recommender system have been proposed to filter out irrelevant information. In the literature, researchers have been mainly dedicated to improving the recommendation performance (accuracy and diversity of the algorithms while they have overlooked the influence of topology of the online user-object bipartite networks. In this paper, we find that some information provided by the bipartite networks is not only redundant but also misleading. With such "less can be more" feature, we design some algorithms to improve the recommendation performance by eliminating some links from the original networks. Moreover, we propose a hybrid method combining the time-aware and topology-aware link removal algorithms to extract the backbone which contains the essential information for the recommender systems. From the practical point of view, our method can improve the performance and reduce the computational time of the recommendation system, thus improving both of their effectiveness and efficiency.

  20. Extracting the Information Backbone in Online System

    Science.gov (United States)

    Zhang, Qian-Ming; Zeng, An; Shang, Ming-Sheng

    2013-01-01

    Information overload is a serious problem in modern society and many solutions such as recommender system have been proposed to filter out irrelevant information. In the literature, researchers have been mainly dedicated to improving the recommendation performance (accuracy and diversity) of the algorithms while they have overlooked the influence of topology of the online user-object bipartite networks. In this paper, we find that some information provided by the bipartite networks is not only redundant but also misleading. With such “less can be more” feature, we design some algorithms to improve the recommendation performance by eliminating some links from the original networks. Moreover, we propose a hybrid method combining the time-aware and topology-aware link removal algorithms to extract the backbone which contains the essential information for the recommender systems. From the practical point of view, our method can improve the performance and reduce the computational time of the recommendation system, thus improving both of their effectiveness and efficiency. PMID:23690946

  1. Temporally rendered automatic cloud extraction (TRACE) system

    Science.gov (United States)

    Bodrero, Dennis M.; Yale, James G.; Davis, Roger E.; Rollins, John M.

    1999-10-01

    Smoke/obscurant testing requires that 2D cloud extent be extracted from visible and thermal imagery. These data are used alone or in combination with 2D data from other aspects to make 3D calculations of cloud properties, including dimensions, volume, centroid, travel, and uniformity. Determining cloud extent from imagery has historically been a time-consuming manual process. To reduce time and cost associated with smoke/obscurant data processing, automated methods to extract cloud extent from imagery were investigated. The TRACE system described in this paper was developed and implemented at U.S. Army Dugway Proving Ground, UT by the Science and Technology Corporation--Acuity Imaging Incorporated team with Small Business Innovation Research funding. TRACE uses dynamic background subtraction and 3D fast Fourier transform as primary methods to discriminate the smoke/obscurant cloud from the background. TRACE has been designed to run on a PC-based platform using Windows. The PC-Windows environment was chosen for portability, to give TRACE the maximum flexibility in terms of its interaction with peripheral hardware devices such as video capture boards, removable media drives, network cards, and digital video interfaces. Video for Windows provides all of the necessary tools for the development of the video capture utility in TRACE and allows for interchangeability of video capture boards without any software changes. TRACE is designed to take advantage of future upgrades in all aspects of its component hardware. A comparison of cloud extent determined by TRACE with manual method is included in this paper.

  2. Ionic Liquid-salt based aqueous biphasic system for quick separation of no-carrier-added 203Pb from proton irradiated natTl2CO3 target

    International Nuclear Information System (INIS)

    Choudhury, Dibyasree; Ghosh, Kaustab; Lahiri, Susanta; Sarkar, Kangkana; Naskar, Nabanita

    2016-01-01

    In the present study, no-carrier-added (NCA) 203 Pb was radiochemically separated from bulk Tl target applying the ABS composing of 4 M K 2 HPO 4 and 0.1 mL of different strengths of IL (bmim)Cl ranging from 40% to 80% (w/v). Bulk Tl was spiked with 200Tl (T 1/2 = 26.1 h). A separation condition was achieved with 70% IL concentration and with 10 min shaking and 10 min settling time, where ∼84% of NCA 203 Pb was extracted into the IL rich phase with ∼10% contamination from bulk Tl. Therefore, further studies, i.e. variation in shaking and settling time were carried out keeping the concentration of IL fixed at 70%

  3. Startup Report for Ground Water Extraction, Treatment, and Recharge System

    National Research Council Canada - National Science Library

    Lamb, Steve

    1997-01-01

    The document presents startup procedures, observations and measurements conducted during the startup of the Groundwater Extraction, Treatment and Recharge System, built for the 162nd Fighter Wing, Air...

  4. Micrometer-scale mixing with Pickering emulsions: biphasic reactions without stirring.

    Science.gov (United States)

    Zhang, Wenjuan; Fu, Luman; Yang, Hengquan

    2014-02-01

    A general strategy that avoids stirring for organic/aqueous reactions involving solid catalysts is reported. The strategy involves converting a conventional biphasic system into a Pickering emulsion phase with micrometer-scale droplets ensuring good mixing. In test reactions, nitrotoluene reduction and epoxidation of allylic alcohols, the reaction efficiency is comparable to conventional stirrer-driven biphasic catalysis reaction systems. Short diffusion distances, arising from the compartmentalization of densely packed droplets, play an important role in boosting the reaction efficiency. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. A new kinetic biphasic approach applied to biodiesel process intensification

    Energy Technology Data Exchange (ETDEWEB)

    Russo, V.; Tesser, R.; Di Serio, M.; Santacesaria, E. [Naples Univ. (Italy). Dept. of Chemistry

    2012-07-01

    Many different papers have been published on the kinetics of the transesterification of vegetable oil with methanol, in the presence of alkaline catalysts to produce biodiesel. All the proposed approaches are based on the assumption of a pseudo-monophasic system. The consequence of these approaches is that some experimental aspects cannot be described. For the reaction performed in batch conditions, for example, the monophasic approach is not able to reproduce the different plateau obtained by using different amount of catalyst or the induction time observed at low stirring rates. Moreover, it has been observed by operating in continuous reactors that micromixing has a dramatic effect on the reaction rate. At this purpose, we have recently observed that is possible to obtain a complete conversion to biodiesel in less than 10 seconds of reaction time. This observation is confirmed also by other authors using different types of reactors like: static mixers, micro-reactors, oscillatory flow reactors, cavitational reactors, microwave reactors or centrifugal contactors. In this work we will show that a recently proposed biphasic kinetic approach is able to describe all the aspects before mentioned that cannot be described by the monophasic kinetic model. In particular, we will show that the biphasic kinetic model can describe both the induction time observed in the batch reactors, at low stirring rate, and the very high conversions obtainable in a micro-channel reactor. The adopted biphasic kinetic model is based on a reliable reaction mechanism that will be validated by the experimental evidences reported in this work. (orig.)

  6. The AGS accelerator complex with the new fast extraction system

    International Nuclear Information System (INIS)

    Tanaka, M.; Bleser, E.J.; Glenn, J.W.; Lee, Y.Y.; Soukas, A.

    1995-01-01

    The delivery of a beam with characteristics appropriate for the g-2 muon storage ring and the filling of the RHIC heavy ion collider from the AGS main ring requires a new fast extracted beam (FEB) system. The new FEB system will be capable of performing both one-turn fast extraction and single bunch multiple extraction of either a heavy ion beam or a high intensity proton beam at a rate of 30 Hz up to 12 times per AGS cycle. The new system consists of a fast multi-pulsing kicker and an ejector septum magnet with local extraction orbit bumps

  7. Biphase sinusoidal oscillator based on negative resistor.

    Science.gov (United States)

    Bayard, Jean

    2010-06-01

    This paper describes a biphase sinusoidal generator which provides two signals: v(ref)=V(M) sin(omegat) and v(out)=V(M) sin(omegat+DeltaPhi), where DeltaPhi is in the range 0, pi/2 or -pi/2, 0 and is not dependent on the frequency value. It is based on a negative resistor and it requires very few components. SPICE simulations and measurements on an experimental setup confirm the theoretical analysis.

  8. The biphasic effects of moderate alcohol consumption with a meal on ambiance-induced mood and autonomic nervous system balance: a randomized crossover trial.

    Directory of Open Access Journals (Sweden)

    Ilse C Schrieks

    Full Text Available BACKGROUND: The pre-drinking mood state has been indicated to be an important factor in the mood effects of alcohol. However, for moderate alcohol consumption there are no controlled studies showing this association. Also, the mood effects of consuming alcohol combined with food are largely unknown. The aim of this study was to investigate the effects of moderate alcohol combined with a meal on ambiance-induced mood states. Furthermore effects on autonomic nervous system activity were measured to explore physiological mechanisms that may be involved in changes of mood state. METHODS: In a crossover design 28 women (age 18-45 y, BMI 18.5-27 kg/m2 were randomly allocated to 4 conditions in which they received 3 glasses of sparkling white wine (30 g alcohol or alcohol-free sparkling white wine while having dinner in a room with either a pleasant or unpleasant created ambiance. Subjects filled out questionnaires (B-BAES, POMS and postprandial wellness questionnaire at different times. Skin conductance and heart rate variability were measured continuously. RESULTS: Moderate alcohol consumption increased happiness scores in the unpleasant, but not in the pleasant ambiance. Alcohol consumption increased happiness and stimulation feelings within 1 hour and increased sedative feelings and sleepiness for 2.5 hour. Skin conductance was increased after alcohol within 1 hour and was related to happiness and stimulation scores. Heart rate variability was decreased after alcohol for 2 hours and was related to mental alertness. CONCLUSION: Mood inductions and autonomic nervous system parameters may be useful to evaluate mood changes by nutritional interventions. Moderate alcohol consumption elevates happiness scores in an unpleasant ambiance. However, drinking alcohol during a pleasant mood results in an equally positive mood state. TRIAL REGISTRATION: Clinicaltrials.gov NCT01426022.

  9. The biphasic effects of moderate alcohol consumption with a meal on ambiance-induced mood and autonomic nervous system balance: a randomized crossover trial.

    Science.gov (United States)

    Schrieks, Ilse C; Stafleu, Annette; Kallen, Victor L; Grootjen, Marc; Witkamp, Renger F; Hendriks, Henk F J

    2014-01-01

    The pre-drinking mood state has been indicated to be an important factor in the mood effects of alcohol. However, for moderate alcohol consumption there are no controlled studies showing this association. Also, the mood effects of consuming alcohol combined with food are largely unknown. The aim of this study was to investigate the effects of moderate alcohol combined with a meal on ambiance-induced mood states. Furthermore effects on autonomic nervous system activity were measured to explore physiological mechanisms that may be involved in changes of mood state. In a crossover design 28 women (age 18-45 y, BMI 18.5-27 kg/m2) were randomly allocated to 4 conditions in which they received 3 glasses of sparkling white wine (30 g alcohol) or alcohol-free sparkling white wine while having dinner in a room with either a pleasant or unpleasant created ambiance. Subjects filled out questionnaires (B-BAES, POMS and postprandial wellness questionnaire) at different times. Skin conductance and heart rate variability were measured continuously. Moderate alcohol consumption increased happiness scores in the unpleasant, but not in the pleasant ambiance. Alcohol consumption increased happiness and stimulation feelings within 1 hour and increased sedative feelings and sleepiness for 2.5 hour. Skin conductance was increased after alcohol within 1 hour and was related to happiness and stimulation scores. Heart rate variability was decreased after alcohol for 2 hours and was related to mental alertness. Mood inductions and autonomic nervous system parameters may be useful to evaluate mood changes by nutritional interventions. Moderate alcohol consumption elevates happiness scores in an unpleasant ambiance. However, drinking alcohol during a pleasant mood results in an equally positive mood state. Clinicaltrials.gov NCT01426022.

  10. The Biphasic Effects of Moderate Alcohol Consumption with a Meal on Ambiance-Induced Mood and Autonomic Nervous System Balance: A Randomized Crossover Trial

    Science.gov (United States)

    Schrieks, Ilse C.; Stafleu, Annette; Kallen, Victor L.; Grootjen, Marc; Witkamp, Renger F.; Hendriks, Henk F. J.

    2014-01-01

    Background The pre-drinking mood state has been indicated to be an important factor in the mood effects of alcohol. However, for moderate alcohol consumption there are no controlled studies showing this association. Also, the mood effects of consuming alcohol combined with food are largely unknown. The aim of this study was to investigate the effects of moderate alcohol combined with a meal on ambiance-induced mood states. Furthermore effects on autonomic nervous system activity were measured to explore physiological mechanisms that may be involved in changes of mood state. Methods In a crossover design 28 women (age 18–45 y, BMI 18.5–27 kg/m2) were randomly allocated to 4 conditions in which they received 3 glasses of sparkling white wine (30 g alcohol) or alcohol-free sparkling white wine while having dinner in a room with either a pleasant or unpleasant created ambiance. Subjects filled out questionnaires (B-BAES, POMS and postprandial wellness questionnaire) at different times. Skin conductance and heart rate variability were measured continuously. Results Moderate alcohol consumption increased happiness scores in the unpleasant, but not in the pleasant ambiance. Alcohol consumption increased happiness and stimulation feelings within 1 hour and increased sedative feelings and sleepiness for 2.5 hour. Skin conductance was increased after alcohol within 1 hour and was related to happiness and stimulation scores. Heart rate variability was decreased after alcohol for 2 hours and was related to mental alertness. Conclusion Mood inductions and autonomic nervous system parameters may be useful to evaluate mood changes by nutritional interventions. Moderate alcohol consumption elevates happiness scores in an unpleasant ambiance. However, drinking alcohol during a pleasant mood results in an equally positive mood state. Trial Registration Clinicaltrials.gov NCT01426022. PMID:24465955

  11. Reactivity of the biphasic trichloroacetonitrile-CH2Cl2/H2O2 system in the epoxidation of soybean oil

    Directory of Open Access Journals (Sweden)

    Martinelli, Márcia

    2002-06-01

    Full Text Available In this work we report on the epoxidation of soybean oil by the trichloroacetonitrile -CH2Cl2/H2O2 byphasic system. The reaction was carried out at room temperature and, most importantly, in non acid conditions which prevent the opening of the oxirane ring. The epoxidized soybean oil was characterized by infrared, 1H and 13C NMR. A maximum conversion of 81 % was achieved in two hours with 86% of selectivity in epoxy groupsEn el presente trabajo informamos sobre la epoxidación de aceite de soja mediante el sistema bifásico tricloroacetonitrilo-CH2Cl2/H2O2. La reacción fue realizada bajo condiciones de temperatura ambiente y, lo más importante, en condición no ácida, lo que evita la apertura del anillo oxirano. El aceite de soja fue caracterizado por infrarrojo y RMN de 1H and 13C. En dos horas se alcanzó una conversión máxima del 81 % obteniéndose una selectividad del 86 % en grupos epóxidos

  12. Study of the anti-inflammatory effects of low-dose radiation. The contribution of biphasic regulation of the antioxidative system in endothelial cells

    Energy Technology Data Exchange (ETDEWEB)

    Large, Martin; Hehlgans, Stephanie; Reichert, Sebastian; Roedel, Claus; Roedel, Franz [Goethe University Frankfurt, Department of Radiotherapy and Oncology, Frankfurt am Main (Germany); Gaipl, Udo S. [University Hospital Erlangen, Department of Radiation Oncology, Erlangen (Germany); Fournier, Claudia [GSI Helmholtz Center for Heavy Ion Research, Department of Biophysics, Darmstadt (Germany); Weiss, Christian [Goethe University Frankfurt, Department of Radiotherapy and Oncology, Frankfurt am Main (Germany); Klinikum Darmstadt, Institute for Radiooncology and Radiotherapy, Darmstadt (Germany)

    2015-09-15

    We examined (a) the expression of the antioxidative factor glutathione peroxidase (GPx) and the transcription factor nuclear factor E2-related factor 2 (Nrf2) following low-dose X-irradiation in endothelial cells (ECs) and (b) the impact of reactive oxygen species (ROS) and Nrf2 on functional properties of ECs to gain further knowledge about the anti-inflammatory mode of action of low doses of ionizing radiation. EA.hy926 ECs and primary human dermal microvascular ECs (HMVEC) were stimulated by tumor necrosis factor-α (TNF-α, 20 ng/ml) 4 h before irradiation with single doses ranging from 0.3 to 3 Gy. The expression and activity of GPx and Nrf2 were analyzed by flow cytometry, colorimetric assays, and real-time PCR. The impact of ROS and Nrf2 on peripheral blood mononuclear cell (PBMC) adhesion was assayed in the presence of the ROS scavenger N-acetyl-L-cysteine (NAC) and Nrf2 activator AI-1. Following a low-dose exposure, we observed in EA.hy926 EC and HMVECs a discontinuous expression and enzymatic activity of GPx concomitant with a lowered expression and DNA binding activity of Nrf2 that was most pronounced at a dose of 0.5 Gy. Scavenging of ROS by NAC and activation of Nrf2 by AI-1 significantly diminished a lowered adhesion of PBMC to EC at a dose of 0.5 Gy. Low-dose irradiation resulted in a nonlinear expression and activity of major compounds of the antioxidative system that might contribute to anti-inflammatory effects in stimulated ECs. (orig.) [German] Ziel der Studie war die Untersuchung der Expression des antioxidativen Enzyms Glutathionperoxidase (GPx) und des Transkriptionsfaktors ''nuclear factor E2-related factor 2'' (Nrf2) in Endothelzellen nach niedrigdosierter Roentgenbestrahlung. Des Weiteren wurde der Einfluss von reaktiven Sauerstoffmetaboliten (ROS) und von Nrf2 auf funktionelle Eigenschaften von Endothelzellen analysiert, um weitere Erkenntnisse ueber die antientzuendliche Wirkung von niedrigdosierten Roentgenstrahlen

  13. Compressive Information Extraction: A Dynamical Systems Approach

    Science.gov (United States)

    2016-01-24

    sparsely encoded in very large data streams. (a) Target tracking in an urban canyon; (b) and (c) sample frames showing contextually abnormal events: onset...tractable convex relaxation can be obtained by using the nuclear norm as a surrogate for rank, leading to a convex semi- definite program that can be...extraction to identify contextually abnormal se- quences (see section 2.2.3). Formally, the problem of interest can be stated as establishing whether a noisy

  14. Temperature dependence of microwave absorption phenomena in single and biphase soft magnetic microwires

    Czech Academy of Sciences Publication Activity Database

    El Kammouni, R.; Vázquez, M.; Lezama, L.; Kurlyandskaya, G.; Kraus, Luděk

    2014-01-01

    Roč. 368, Nov (2014), 126-132 ISSN 0304-8853 Institutional support: RVO:68378271 Keywords : magnetic microwire * ferromagnetic resonance * microwave absorption * biphase magnetic system Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.970, year: 2014

  15. Preliminary thermal analysis of grids for twin source extraction system

    International Nuclear Information System (INIS)

    Pandey, Ravi; Bandyopadhyay, Mainak; Chakraborty, Arun K.

    2017-01-01

    The TWIN (Two driver based Indigenously built Negative ion source) source provides a bridge between the operational single driver based negative ion source test facility, ROBIN in IPR and an ITER-type multi driver based ion source. The source is designed to be operated in CW mode with 180kW, 1MHz, 5s ON/600s OFF duty cycle and also in 5Hz modulation mode with 3s ON/20s OFF duty cycle for 3 such cycle. TWIN source comprises of ion source sub-assembly (consist of driver and plasma box) and extraction system sub-assembly. Extraction system consists of Plasma grid (PG), extraction grid (EG) and Ground grid (GG) sub assembly. Negative ion beams produced at plasma grid seeing the plasma side of ion source will receive moderate heat flux whereas the extraction grid and ground grid would be receiving majority of heat flux from extracted negative ion and co-extracted electron beams. Entire Co-extracted electron beam would be dumped at extraction grid via electron deflection magnetic field making the requirement of thermal and hydraulic design for extraction grid to be critical. All the three grids are made of OFHC Copper and would be actively water cooled keeping the peak temperature rise of grid surface within allowable limit with optimum uniformity. All the grids are to be made by vacuum brazing process where joint strength becomes crucial at elevated temperature. Hydraulic design must maintain the peak temperature at the brazing joint within acceptable limit

  16. Slow extraction control system of HIRFL-CSR

    International Nuclear Information System (INIS)

    Liu Wufeng; Qiao Weimin; Yuan Youjin; Mao Ruishi; Zhao Tiecheng

    2013-01-01

    For heavy-ion radiotherapy, HIRFL-CSR (Heavy Ion Research Facility in Lanzhou-Cooler Storage Ring) needs a long term uniform ion beam extraction from HIRFL-CSR main ring to high energy beam transport line to meet the requirement of heavy-ion radiotherapy's ion beam. Slow extraction control system uses the synchronous signal of HIRFL-CSR control system's timing system to realize process control. When the synchronous event data of HIRFL-CSR control system's timing system trigger controlling and changing data (frequency value, tune value, voltage value), the waveform generator will generate waveform by frequency value, tune value and voltage value, and will amplify the generated waveform by power amplifier to electrostatic deflector to achieve RF-KO slow extraction. The synchronous event receiver of slow extraction system is designed by using FPGA and optical fiber interface to keep high transmission speed and anti-jamming. HIRFL-CSR's running for heavy-ion radiotherapy and ten thousand seconds long period slow extraction experiments show that slow extraction control system is workable and can meet the requirement of heavy-ion radiotherapy's ion beam. (authors)

  17. Genotoxicity assessment of biphasic calcium phosphate of modified porosity on human dental pulp cells using Ames and Comet assays.

    Science.gov (United States)

    Wahab, Nur Fathin Alia Che; Kannan, Thirumulu Ponnuraj; Mahmood, Zuliani; Rahman, Ismail Ab; Ismail, Hanafi

    2018-03-01

    Biphasic Calcium Phosphate (BCP) with a ratio of 20/80 Hydroxyapatite (HA)/Beta-tricalcium phosphate (β-TCP) promotes the differentiation of human dental pulp cells (HDPCs). In the current study, the genotoxicity of locally produced BCP of modified porosity (65%) with a mean pore size of 300micrometer (μm) was assessed using Comet and Ames assays. HDPCs were treated with BCP extract at three different inhibitory concentrations which were obtained based on cytotoxicity test conducted with concurrent negative and positive controls. The tail moment of HDPCs treated with BCP extract at all three concentrations showed no significant difference compared to negative control (p>0.05), indicating that BCP did not induce DNA damage to HDPCs. The BCP was evaluated using five tester strains of Salmonella typhimurium TA98, TA100, TA102, TA1537 and TA1538. Each strain was incubated with BCP extract with five different concentrations in the presence and absence of metabolic activation system (S9) mix. Concurrently, negative and positive controls were included. The average number of revertant colonies per plate treated with the BCP extract was less than double as compared to the number of revertant colonies in negative control plate and no dose-related increase was observed. Results from both assays suggested that the BCP of modified porosity did not exhibit any genotoxic effect under the present test conditions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Beam extraction control systems of the fast-cycling synchrotron

    International Nuclear Information System (INIS)

    Toumanian, A.; Zapolski, N.; Nickogosian, V.; Ananian, A.; Kazarian, A.; Khoetsian, M.; Agababian, A.; Matevosian, A.

    1992-01-01

    A compact system controlling the extraction of different beams (gamma, electron, synchrotron radiation) in single and simultaneous operation modes at high electromagnetic disturbances level based on using one computer of IBM PC/AT type is described. (author)

  19. LHC beam dumping system Extraction channel layout and acceptance

    CERN Document Server

    Goddard, B; Uythoven, J; Veness, R; Weterings, W

    2003-01-01

    The LHC beam dumping system must safely abort the LHC beams under all conditions, including those resulting from abnormal behaviour of machine elements or subsystems of the beam dumping system itself. The extraction channels must provide sufficient aperture both for the circulating and extracted beams, over the whole energy range and under various beam parameters. These requirements impose tight constraints on the tolerances of various extraction channel components, and also on the allowed range of beam positions in the region of these components. Operation of the beam dumping system under various fault states has been considered, and the resulting apertures calculated. After describing briefly the beam dumping system and the extraction channel geometry, the various assumptions made in the analysis are presented, before deriving tolerance limits for the relevant equipment and beam parameters.

  20. Biphasic activity of a jumping spider

    Science.gov (United States)

    Okuyama, Toshinori

    2011-01-01

    Individual variation is a ubiquitous and important factor that affects ecological dynamics. This study examined individual variation in the nest-use pattern of the jumping spider Phidippus audax. Although the jumping spider is a diurnal species, field observations in this study revealed that the majority of individuals remained in their nests during the day. An accompanying examination of the hunger level of the spiders revealed that spiders that remained in nests were more starved than those observed outside nests. If spiders actively forage when they are starved, as has been suggested by previous studies, one would expect to see the opposite trend (i.e., spiders that remained in nests are more satiated). Thus, the pattern observed in the field contradicts the known behavioral pattern of the spiders. An individual-based model was used to investigate the behavioral mechanism of the spider and the discrepancy found in the observations. A basic assumption of the model is that spiders possess distinct inactive and active phases (biphasic activity pattern), and transitions between the two phases are regulated by the hunger level of the spider. Data from a laboratory experiment were used to examine the assumptions of the model partially. The model was able to capture patterns observed in the data, suggesting that the pattern of transitions in biphasic activity is an important trait of the foraging behavior of the jumping spider.

  1. Statistical feature extraction based iris recognition system

    Indian Academy of Sciences (India)

    Performance of the proposed iris recognition system (IRS) has been measured by recording false acceptance rate (FAR) and false rejection rate (FRR) at differentthresholds in the distance metric. System performance has been evaluated by computing statistical features along two directions, namely, radial direction of ...

  2. Interaction of Plant Extracts with Central Nervous System Receptors

    Directory of Open Access Journals (Sweden)

    Kenneth Lundstrom

    2017-02-01

    Full Text Available Background: Plant extracts have been used in traditional medicine for the treatment of various maladies including neurological diseases. Several central nervous system receptors have been demonstrated to interact with plant extracts and components affecting the pharmacology and thereby potentially playing a role in human disease and treatment. For instance, extracts from Hypericum perforatum (St. John’s wort targeted several CNS receptors. Similarly, extracts from Piper nigrum, Stephania cambodica, and Styphnolobium japonicum exerted inhibition of agonist-induced activity of the human neurokinin-1 receptor. Methods: Different methods have been established for receptor binding and functional assays based on radioactive and fluorescence-labeled ligands in cell lines and primary cell cultures. Behavioral studies of the effect of plant extracts have been conducted in rodents. Plant extracts have further been subjected to mood and cognition studies in humans. Results: Mechanisms of action at molecular and cellular levels have been elucidated for medicinal plants in support of standardization of herbal products and identification of active extract compounds. In several studies, plant extracts demonstrated affinity to a number of CNS receptors in parallel indicating the complexity of this interaction. In vivo studies showed modifications of CNS receptor affinity and behavioral responses in animal models after treatment with medicinal herbs. Certain plant extracts demonstrated neuroprotection and enhanced cognitive performance, respectively, when evaluated in humans. Noteworthy, the penetration of plant extracts and their protective effect on the blood-brain-barrier are discussed. Conclusion: The affinity of plant extracts and their isolated compounds for CNS receptors indicates an important role for medicinal plants in the treatment of neurological disorders. Moreover, studies in animal and human models have confirmed a scientific basis for the

  3. Antioxidant Activity of Flaxseed Extracts in Lipid Systems

    Directory of Open Access Journals (Sweden)

    Adriana Slavova-Kazakova

    2015-12-01

    Full Text Available The aim of this work was to compare the antioxidant activity of the extract of flaxseed and its alkaline hydrolysate in two model systems: lipid autoxidation of triacylglycerols of sunflower oil (TGSO—in a homogeneous lipid media and during β-carotene-linoleate emulsion system. In addition, pure lignans were tested. The material was defatted with hexane and then phenolic compounds were extracted using dioxane-ethanol (50:50, v/v mixture. Carbohydrates were removed from the crude extract using an Amberlite XAD-16 column chromatography. The content of total phenolic compounds in the crude extract and after alkaline hydrolysis was determined using a Folin-Ciocalteu’s phenol reagent. Individual phenolic compounds were determined by nordihydroguaiaretic acid (RP-HPLC method in gradient system. The alkaline hydrolysis increased the content of total phenolics in the extract approximately by 10%. In the extracts of flaxseed, phenolic compounds were present in the form of macromolecular complex. In the alkaline hydrolysate, secoisolariciresinol diglucoside (SDG was found as the main phenolic compound. Small amounts of p-coumaric and ferulic acids were also determined. SDG and both extracts were not able to inhibit effectively lipid autoxidation. The kinetics of TGSO autoxidation at 80 °C in absence and in presence of the extract before hydrolysis (EBH and after hydrolysis (EAH was monitored and compared with known standard antioxidants. Ferulic acid (FA and butylated hydroxyl toluene (BHT showed much higher antioxidant efficiency and reactivity than that of both extracts. Secoisolariciresinol (SECO showed a higher activity in both model systems than SDG. However, the activity of SECO was much lower than that of nordihydroquaiaretic acid (NDGA.

  4. A functional biphasic biomaterial homing mesenchymal stem cells for in vivo cartilage regeneration.

    Science.gov (United States)

    Huang, Hongjie; Zhang, Xin; Hu, Xiaoqing; Shao, Zhenxing; Zhu, Jingxian; Dai, Linghui; Man, Zhentao; Yuan, Lan; Chen, Haifeng; Zhou, Chunyan; Ao, Yingfang

    2014-12-01

    Cartilage regeneration after trauma is still a great challenge for clinicians and researchers due to many reasons, such as joint load-bearing, synovial movement and the paucity of endogenous repair cells. To overcome these limitations, we constructed a functional biomaterial using a biphasic scaffold platform and a bone-derived mesenchymal stem cells (BMSCs)-specific affinity peptide. The biphasic scaffold platform retains more cells homogeneously within the sol-gel transition of chitosan and provides sufficient solid matrix strength. This biphasic scaffold platform is functionalized with an affinity peptide targeting a cell source of interest, BMSCs. The presence of conjugated peptide gives this system a biological functionality towards BMSC-specific homing both in vitro and in vivo. The functional biomaterial can stimulate stem cell proliferation and chondrogenic differentiation during in vitro culture. Six months after in vivo implantation, compared with routine surgery or control scaffolds, the functional biomaterials induced superior cartilage repair without complications, as indicated by histological observations, magnetic resonance imaging and biomechanical properties. Beyond cartilage repair, this functional biphasic scaffold may provide a biomaterial framework for one-step tissue engineering strategy by homing endogenous cells to stimulate tissue regeneration. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. ChemEx: information extraction system for chemical data curation.

    Science.gov (United States)

    Tharatipyakul, Atima; Numnark, Somrak; Wichadakul, Duangdao; Ingsriswang, Supawadee

    2012-01-01

    Manual chemical data curation from publications is error-prone, time consuming, and hard to maintain up-to-date data sets. Automatic information extraction can be used as a tool to reduce these problems. Since chemical structures usually described in images, information extraction needs to combine structure image recognition and text mining together. We have developed ChemEx, a chemical information extraction system. ChemEx processes both text and images in publications. Text annotator is able to extract compound, organism, and assay entities from text content while structure image recognition enables translation of chemical raster images to machine readable format. A user can view annotated text along with summarized information of compounds, organism that produces those compounds, and assay tests. ChemEx facilitates and speeds up chemical data curation by extracting compounds, organisms, and assays from a large collection of publications. The software and corpus can be downloaded from http://www.biotec.or.th/isl/ChemEx.

  6. The graphic model of the spent fuel rod extracting system

    International Nuclear Information System (INIS)

    Yoon, Jee Sup; Kim, Sung Hyun

    1997-01-01

    The spent fuel rod extracting system is being developed in KAERI to deal with problems associated with utilization of storage pools at nuclear power plants. This system consists of an equipment system for extracting rods from spent fuel assemblies, a machine controller, and a supervisory controller. The performance of extraction system has been investigated through a series of experiments. Even though the system is designed to automatically perform sequential procedures, several problems have been found such as the gripper stucking to fuel rod caused by misaligned positioning and the socket jamming of impact wrench into the nut, etc. Up to this end the graphical model of the rod extracting system has been made so that possible sequences of operations including error detection and recovery actions are verified by using a graphic simulation before real operations. For the implementation, IGRIP is being used as a multifunctional tool for developing the rod extraction system. IGRIP is not only an excellent visualization tool, but it also highlights modeling virtual machine. (author). 6 refs., 1 tab., 6 figs

  7. Abu Dhabi's strategic tunnel enhancement programme: odour extraction system approaches.

    Science.gov (United States)

    Cowden, Scott; Witherspoon, Jay; Orakzai, Shahzad; Krause, T

    2012-01-01

    The Emirate of Abu Dhabi has experienced tremendous growth since the mid-1970s resulting in significant overloading of its existing sewerage system. Master planning determined that the best long-term wastewater collection and conveyance solution was construction of a deep tunnel sewer system. Implementation of this massive project faced numerous challenges, including the goal of no odours and limited odour control facilities. To accomplish this, the consultant team examined a unique approach of a single odour control system installed at the proposed downstream tunnel pumping station. Rigorous analysis utilising computer-based models confirmed the viability of this approach. However, other approaches including multiple satellite (localised or regional) odour extraction systems were considered. To better understand entrained air forces at vortex drops, and to confirm the preferred odour extraction approach, physical modelling of drop structures and overall tunnel system was implemented. Results and findings concluded that a regional odour extraction system approach was preferred over a single (centralised) extraction approach. This paper focuses on the process of selecting the preferred odour extraction approach and preliminary capacity sizing of regional systems.

  8. Comparison of defibrillation efficacy using biphasic waveforms delivered from various capacitances/pulse widths.

    Science.gov (United States)

    Lin, J H; Stotts, L J; Rosborough, J P; Frederick, H

    1997-01-01

    The efficacy of the biphasic waveform shock for the defibrillation of the ventricular myocardium has been reported by researchers and physicians. Although many authors have suggested that biphasic waveforms delivered from lower capacitances and shorter pulse widths could result in the reduction of the energy required for successful defibrillation, no report has described the smallest capacitance and pulse width yielding the lowest DFT. In this study, we compared efficacies of the biphasic waveform shocks and DFT safety margins among five different capacitances (175 mu f, 125 mu f. 100 mu f. 75 mu f, and 50 mu f) combined with 1-3 pulse widths. These experiments performed in six dogs used an endocardial lead/subcutaneous patch defibrillation electrode system. The average DFTs at E50 for 175 mu f (6.5/3.5 ms), 125 mu f (6.5/3.5 ms), 100 mu f (6.0/3.0 ms), 75 mu f (4.0/2.0) ms, and 50 mu f (3.0/2.0 ms) were 8.5, 10.0, 11.0, 14.0, and 16.5), respectively. These results indicate that a biphasic waveform delivered from a larger capacitance with a proper pulse width could achieve a higher defibrillation efficacy. All DFTs at E50 for all waveforms were compared to their deliverable energies and maximum stored energies. This comparison indicated a narrow DFT safety margin with capacitances below 100 mu f. Therefore, it is concluded that higher energy and higher leading edge voltage are required for a biphasic waveform delivered from a smaller capacitance with a shorter pulse width. Since the current capacitor technology provides a maximum voltage of 750 V using two capacitors in series, with the electrode impedance system used in this study, smaller capacitors appear to have a decreased probability of defibrillation success at a given energy.

  9. Smart Extraction and Analysis System for Clinical Research.

    Science.gov (United States)

    Afzal, Muhammad; Hussain, Maqbool; Khan, Wajahat Ali; Ali, Taqdir; Jamshed, Arif; Lee, Sungyoung

    2017-05-01

    With the increasing use of electronic health records (EHRs), there is a growing need to expand the utilization of EHR data to support clinical research. The key challenge in achieving this goal is the unavailability of smart systems and methods to overcome the issue of data preparation, structuring, and sharing for smooth clinical research. We developed a robust analysis system called the smart extraction and analysis system (SEAS) that consists of two subsystems: (1) the information extraction system (IES), for extracting information from clinical documents, and (2) the survival analysis system (SAS), for a descriptive and predictive analysis to compile the survival statistics and predict the future chance of survivability. The IES subsystem is based on a novel permutation-based pattern recognition method that extracts information from unstructured clinical documents. Similarly, the SAS subsystem is based on a classification and regression tree (CART)-based prediction model for survival analysis. SEAS is evaluated and validated on a real-world case study of head and neck cancer. The overall information extraction accuracy of the system for semistructured text is recorded at 99%, while that for unstructured text is 97%. Furthermore, the automated, unstructured information extraction has reduced the average time spent on manual data entry by 75%, without compromising the accuracy of the system. Moreover, around 88% of patients are found in a terminal or dead state for the highest clinical stage of disease (level IV). Similarly, there is an ∼36% probability of a patient being alive if at least one of the lifestyle risk factors was positive. We presented our work on the development of SEAS to replace costly and time-consuming manual methods with smart automatic extraction of information and survival prediction methods. SEAS has reduced the time and energy of human resources spent unnecessarily on manual tasks.

  10. Qualitative feature extractions of chaotic systems

    International Nuclear Information System (INIS)

    Vicha, T.; Dohnal, M.

    2008-01-01

    The theory of chaos offers useful tools for systems analysis. However, models of complex systems are based on a network of inconsistent, space and uncertain knowledge items. Traditional quantitative methods of chaos analysis are therefore not applicable. The paper by the same authors [Vicha T, Dohnal M. Qualitative identification of chaotic systems behaviours. Chaos, Solitons and Fractals, in press, [Log. No. 601019] ] presents qualitative interpretation of some chaos concepts. There are only three qualitative values positive/increasing, negative/decreasing and zero/constant. It means that any set of qualitative multidimensional descriptions of unsteady state behaviours is discrete and finite. A finite upper limit exists for the total number of qualitatively distinguishable scenarios. A set of 21 published chaotic models is solved qualitatively and 21 sets of all existing qualitative scenarios are presented. The intersection of all 21 scenario sets is empty. There is no such a behaviour which is common for all 21 models. The set of 21 qualitative models (e.g. Lorenz, Roessler) can be used to compare chaotic behaviours of an unknown qualitative model with them to evaluate if its chaotic behaviours is close to e.g. Lorenz chaotic model and how much

  11. Obtaining of ceramics biphasic dense and porous

    International Nuclear Information System (INIS)

    Pallone, E.M.J.A.; Rigo, E.C.S.; Fraga, A.F.

    2010-01-01

    Among the bioceramic hydroxyapatite (HAP) and beta-tricalcium phosphate (beta-TCP) are materials commonly used in biomedical field. Their combined properties result in a material with absorbable and at the same time with bioactive surface. Called biphasic ceramics such materials respond more quickly when exposed to physiological environment. In this work, powders of HAP/beta-TCP were obtained by chemical precipitation. After obtaining the post-phase was added at a ratio of 0, 15% and 30w% aqueous solutions of corn starch in order to obtain porous bodies. After mixing the resulting solutions were dried, resigned in tablet form and sintered at 1300 deg C. The initial powder was characterized by X-ray diffraction with Rietveld refinement to quantify the phases present. Bodies-of-evidence has been characterized by calculating the bulk density, X-ray diffraction (XRD), scanning electron microscopy and diametral compression. (author)

  12. Biphasic versus monophasic waveforms for transthoracic defibrillation in out-of-hospital cardiac arrest.

    Science.gov (United States)

    Faddy, Steven C; Jennings, Paul A

    2016-02-10

    Transthoracic defibrillation is a potentially life-saving treatment for people with ventricular fibrillation (VF) and haemodynamically unstable ventricular tachycardia (VT). In recent years, biphasic waveforms have become more commonly used for defibrillation than monophasic waveforms. Clinical trials of internal defibrillation and transthoracic defibrillation of short-duration arrhythmias of up to 30 seconds have demonstrated the superiority of biphasic waveforms over monophasic waveforms. However, out-of-hospital cardiac arrest (OHCA) involves a duration of VF/VT of several minutes before defibrillation is attempted. To determine the efficacy and safety of biphasic defibrillation waveforms, compared to monophasic, for resuscitation of people experiencing out-of-hospital cardiac arrest. We searched the following electronic databases for potentially relevant studies up to 10 September 2014: the Cochrane Central Register of Controlled Trials (CENTRAL), MEDLINE and EMBASE. Also we checked the bibliographies of relevant studies and review articles, contacted authors of published reviews and reviewed webpages (including those of device manufacturers) relevant to the review topic. We handsearched the abstracts of conference proceedings for the American Heart Association, American College of Cardiology, European Society of Cardiology, European Resuscitation Council, Society of Critical Care Medicine and European Society of Intensive Care Medicine. Regarding language restrictions, we did not apply any. We included randomised controlled trials (RCTs) that compared biphasic and monophasic waveform defibrillation in adults with OHCA. Two review authors independently screened the literature search results. Two review authors independently extracted data from the included trials and performed 'Risk of bias' assessments. We resolved any disagreements by discussion and consensus. The primary outcome was the risk of failure to achieve return of spontaneous circulation (ROSC

  13. Operation and Performance of a Biphase Turbine Power Plant at the Cerro Prieto Geothermal Field (Final Report)

    Energy Technology Data Exchange (ETDEWEB)

    Hays, Lance G. [Douglas Energy Company, Placentia, CA (United States)

    2000-09-01

    % after implementations of this method in March 2000. However, failures of instrumentation and control system components led to additional plant down time and damage to the bearings and seals. The enthalpy and pressure of well 103 declined substantially from the inception of the project. When the project was started the wellhead pressure and enthalpy were 760 psig and 882 Btu/lb respectively. At the time the plant was placed in standby the corresponding values were only 525 psig and 658 Btu/lb. This reduced the available plant power to only 400 kWe making the project economically unfeasible. However, replacement of the existing rotor with the Dual Pressure Rotor and replacement of the bearings and seals will enable the existing Biphase turbine to produce 1190 kWe at the present well conditions without the backpressure steam turbine. Operation with the present staff can then be sustained by selling power under the existing Agreement with CFE. Implementation of this option is recommended with operation of the facility to continue as a demonstration plant. Biphase turbine theory, design and performance are reported herein. The construction of the Biphase turbine and power plant and operational experience are detailed. Improvements in the Biphase turbine are indicated and analyzed. The impact of Biphase techonology on geothermal power production is discussed and recommendations made.

  14. Extractive text summarization system to aid data extraction from full text in systematic review development.

    Science.gov (United States)

    Bui, Duy Duc An; Del Fiol, Guilherme; Hurdle, John F; Jonnalagadda, Siddhartha

    2016-12-01

    Extracting data from publication reports is a standard process in systematic review (SR) development. However, the data extraction process still relies too much on manual effort which is slow, costly, and subject to human error. In this study, we developed a text summarization system aimed at enhancing productivity and reducing errors in the traditional data extraction process. We developed a computer system that used machine learning and natural language processing approaches to automatically generate summaries of full-text scientific publications. The summaries at the sentence and fragment levels were evaluated in finding common clinical SR data elements such as sample size, group size, and PICO values. We compared the computer-generated summaries with human written summaries (title and abstract) in terms of the presence of necessary information for the data extraction as presented in the Cochrane review's study characteristics tables. At the sentence level, the computer-generated summaries covered more information than humans do for systematic reviews (recall 91.2% vs. 83.8%, psummarization system. Copyright © 2016 Elsevier Inc. All rights reserved.

  15. Optical characteristics of two electrode and three electrode extraction system of an ECR-ion source

    International Nuclear Information System (INIS)

    Siljegovic, M.; Dobrosavljevic, A.

    2001-01-01

    Two extraction systems, single gap extraction system and accel-decel three electrode extraction system, are investigated. The extraction of ions from ECR-sources is usually done in a single extraction gap. But, this type of extraction system has the disadvantage of a low flexibility during operation. In the case of accel-decel system, optimisation of its optical characteristics, in respect to certain ion species, is simply performed by changing the negative potential on the screening electrode (author)

  16. Influence of Biphasic Stimulation on Olfactory Ensheathing Cells for Neuroprosthetic Devices

    OpenAIRE

    Rachelle Therese Hassarati; Leslie John Foster; Rylie Adelle Green; Rylie Adelle Green

    2016-01-01

    The recent success of olfactory ensheathing cell (OEC) assisted regeneration of injured spinal cord has seen a rising interest in the use of these cells in tissue-engineered systems. Previously shown to support neural cell growth through glial scar tissue, OECs have the potential to assist neural network formation in living electrode systems to produce superior neuroprosthetic electrode surfaces. The following study sought to understand the influence of biphasic electrical stimulation (ES), i...

  17. X-ray studies of interfacial strontium-extractant complexes in a model solvent extraction system.

    Science.gov (United States)

    Bu, Wei; Mihaylov, Miroslav; Amoanu, Daniel; Lin, Binhua; Meron, Mati; Kuzmenko, Ivan; Soderholm, L; Schlossman, Mark L

    2014-10-30

    The interfacial behavior of a model solvent extraction liquid-liquid system, consisting of solutions of dihexadecyl phosphate (DHDP) in dodecane and SrCl2 in water, was studied to determine the structure of the interfacial ion-extractant complex and its variation with pH. Previous experiments on a similar extraction system with ErCl3 demonstrated that the kinetics of the extraction process could be greatly retarded by cooling through an adsorption transition, thus providing a method to immobilize ion-extractant complexes at the interface and further characterize them with X-ray interface-sensitive techniques. Here, we use this same method to study the SrCl2 system. X-ray reflectivity and fluorescence near total reflection measured the molecular-scale interfacial structure above and below the adsorption transition for a range of pH. Below the transition, DHDP molecules form a homogeneous monolayer at the interface with Sr(2+) coverage increasing from zero to saturation (one Sr(2+) per two DHDP) within a narrow range of pH. Experimental values of Sr(2+) interfacial density determined from fluorescence measurements are larger than those from reflectivity measurements. Although both techniques probe Sr(2+) bound to DHDP, only the fluorescence provides adequate sensitivity to Sr(2+) in the diffuse double layer. A Stern equation determines the Sr(2+) binding constant from the reflectivity measurements and the additional Sr(2+) measured in the diffuse double layer is accounted for by Gouy-Chapman theory. Above the transition temperature, a dilute concentration of DHDP-Sr complexes resides at the interface, even for temperatures far above the transition. A comparison is made of the structure of the interfacial ion-extractant complex for this divalent metal ion to recent results on trivalent Er(3+) metal ions, which provides insight into the role of metal ion charge on the structure of interfacial ion-extractant complexes, as well as implications for extraction of these two

  18. A Risk Assessment System with Automatic Extraction of Event Types

    Science.gov (United States)

    Capet, Philippe; Delavallade, Thomas; Nakamura, Takuya; Sandor, Agnes; Tarsitano, Cedric; Voyatzi, Stavroula

    In this article we describe the joint effort of experts in linguistics, information extraction and risk assessment to integrate EventSpotter, an automatic event extraction engine, into ADAC, an automated early warning system. By detecting as early as possible weak signals of emerging risks ADAC provides a dynamic synthetic picture of situations involving risk. The ADAC system calculates risk on the basis of fuzzy logic rules operated on a template graph whose leaves are event types. EventSpotter is based on a general purpose natural language dependency parser, XIP, enhanced with domain-specific lexical resources (Lexicon-Grammar). Its role is to automatically feed the leaves with input data.

  19. Central nervous system activity of Illicium verum fruit extracts.

    Science.gov (United States)

    Chouksey, Divya; Upmanyu, Neeraj; Pawar, R S

    2013-11-01

    To research the acute toxicity of Illicium verum (I. verum) fruit extracts and its action on central nervous system. The TLC and HPTLC techniques were used as fingerprints to determine the chemical components present in I. verum. Male albino rats and mice were utilized for study. The powdered material was successively extracted with n-hexane, ethyl acetate and methanol using a Soxhlet extractor. Acute toxicity studies were performed as per OECD guidelines. The CNS activity was evaluated on parameters of general behavior, sleeping pattern, locomotor activity, anxiety and myocoordination activity. The animals were trained for seven days prior to experiments and the divided into five groups with six animals in each. The drug was administered by intraperitoneal route according to body weight. The dosing was done as prescribed in each protocol. Toxicity studies reported 2 000 mg/kg as toxicological dose and 1/10 of the same dose was taken as therapeutic dose Intraperitoneal injection of all extracts at dose of 200 mg prolonged phenobarbitone induced sleeping time, produced alteration in general behavior pattern, reduced locomotor activity and produced anxiolytic effects but the extracts do not significantly alter muscles coordination activity. The three extracts of I. verum at the dose of 200 mg, methanol extract was found to produce more prominent effects, then hexane and ethylacetate extracts. The observation suggested that the extracts of I. verum possess potent CNS depressant action and anxiolytic effect without interfering with motor coordination. Copyright © 2013 Hainan Medical College. Published by Elsevier B.V. All rights reserved.

  20. MBA: a literature mining system for extracting biomedical abbreviations.

    Science.gov (United States)

    Xu, Yun; Wang, ZhiHao; Lei, YiMing; Zhao, YuZhong; Xue, Yu

    2009-01-09

    The exploding growth of the biomedical literature presents many challenges for biological researchers. One such challenge is from the use of a great deal of abbreviations. Extracting abbreviations and their definitions accurately is very helpful to biologists and also facilitates biomedical text analysis. Existing approaches fall into four broad categories: rule based, machine learning based, text alignment based and statistically based. State of the art methods either focus exclusively on acronym-type abbreviations, or could not recognize rare abbreviations. We propose a systematic method to extract abbreviations effectively. At first a scoring method is used to classify the abbreviations into acronym-type and non-acronym-type abbreviations, and then their corresponding definitions are identified by two different methods: text alignment algorithm for the former, statistical method for the latter. A literature mining system MBA was constructed to extract both acronym-type and non-acronym-type abbreviations. An abbreviation-tagged literature corpus, called Medstract gold standard corpus, was used to evaluate the system. MBA achieved a recall of 88% at the precision of 91% on the Medstract gold-standard EVALUATION Corpus. We present a new literature mining system MBA for extracting biomedical abbreviations. Our evaluation demonstrates that the MBA system performs better than the others. It can identify the definition of not only acronym-type abbreviations including a little irregular acronym-type abbreviations (e.g., ), but also non-acronym-type abbreviations (e.g., ).

  1. Terra Vac In Situ Vacuum Extraction System: Applications Analysis Report

    Science.gov (United States)

    This document is an evaluation of the Terra Vac in situ vacuum extraction system and its applicability as a treatment method for waste site cleanup. This report analyzes the results from the Superfund Innovative Technology Evaluation (SITE) Program’s 56-day demonstration at t...

  2. Extracted-beam-detection system around synchrotron saturne

    International Nuclear Information System (INIS)

    Anne, Remy; Milleret, Gerard; Giuliani, Arlette; Lefol, Andre; Perret, Robert; Poupard, Joseph; Trogno, Andre; Van den Bossche, Maurice; N'Guyen Sieu Viet.

    1977-07-01

    The extracted-beam-detection system working around the synchrotron Saturne is presented. The whole system is composed of about forty multiwire chambers used for beam tuning and providing beams profiles. Optic beam parameters such as position, divergence, dimension, emittance can be easily measured, or calculated with a program running on a computer. They are working in large range intensity beams (10 2 to 5.10 11 p/cm 2 /s of protons, alpha particles, deutons, pions, tritons and electrons [fr

  3. System and method for extracting a sample from a surface

    Science.gov (United States)

    Van Berkel, Gary; Covey, Thomas

    2015-06-23

    A system and method is disclosed for extracting a sample from a sample surface. A sample is provided and a sample surface receives the sample which is deposited on the sample surface. A hydrophobic material is applied to the sample surface, and one or more devices are configured to dispense a liquid on the sample, the liquid dissolving the sample to form a dissolved sample material, and the one or more devices are configured to extract the dissolved sample material from the sample surface.

  4. Biphasic Scaffolds from Marine Collagens for Regeneration of Osteochondral Defects

    Directory of Open Access Journals (Sweden)

    Anne Bernhardt

    2018-03-01

    Full Text Available Background: Collagens of marine origin are applied increasingly as alternatives to mammalian collagens in tissue engineering. The aim of the present study was to develop a biphasic scaffold from exclusively marine collagens supporting both osteogenic and chondrogenic differentiation and to find a suitable setup for in vitro chondrogenic and osteogenic differentiation of human mesenchymal stroma cells (hMSC. Methods: Biphasic scaffolds from biomimetically mineralized salmon collagen and fibrillized jellyfish collagen were fabricated by joint freeze-drying and crosslinking. Different experiments were performed to analyze the influence of cell density and TGF-β on osteogenic differentiation of the cells in the scaffolds. Gene expression analysis and analysis of cartilage extracellular matrix components were performed and activity of alkaline phosphatase was determined. Furthermore, histological sections of differentiated cells in the biphasic scaffolds were analyzed. Results: Stable biphasic scaffolds from two different marine collagens were prepared. An in vitro setup for osteochondral differentiation was developed involving (1 different seeding densities in the phases; (2 additional application of alginate hydrogel in the chondral part; (3 pre-differentiation and sequential seeding of the scaffolds and (4 osteochondral medium. Spatially separated osteogenic and chondrogenic differentiation of hMSC was achieved in this setup, while osteochondral medium in combination with the biphasic scaffolds alone was not sufficient to reach this ambition. Conclusions: Biphasic, but monolithic scaffolds from exclusively marine collagens are suitable for the development of osteochondral constructs.

  5. Electron beam extraction system with a ring radiation field

    International Nuclear Information System (INIS)

    Auslender, V.L.; Kuksanov, N.K.; Polyakov, V.A.; Salimov, R.A.; Chertok, I.L.

    1979-01-01

    Description and results of testings of two electron beam extraction systems for shaping of a circular irradiation field are given. One of the systems contains three 20 cm long outlet windows arranged at 120 deg angle with respect to each other. Tests at the ILU-6 accelerator have shown that the given system provides 150 mm zone irradiation from three sides. Beam utilization factor when irradiating three 40 mm dia tubes amounted to 35% which provides capacity of 2.5 txMrad/h at 20 kW beam power. The other extraction system includes two C-form magnets producing nonuniform and opposing magnetic fields. This system tests at the EhLV-2 accelerator have shown that at 0.8-1.5 MeV electron energy it is possible to irradiate of 60 and 100 mm dia objects, accordingly. The system may be used together with both constant-action and pulse-action accelerators having extraction with linear scanning [ru

  6. New biphasic monocomponent composite material obtained by the partial oxypropylation of bacterial cellulose

    International Nuclear Information System (INIS)

    Rosa, Joyce Rover; Silva, Ingrid S.V. da; Pasquini, Daniel; Santos, Daniele B. dos; Barud, Hernane S.; Ribeiro, Sidney J.L.

    2011-01-01

    This study aimed to partial oxypropylation of bacterial cellulose (CB), as well as the characterization of pure CB, oxypropylated CB (CBO) and oxypropylated CB after Soxhlet extraction with hexane (CBOE). The oxypropylation reaction was carried out by propylene oxide polymerization, catalyzed by KOH, in the presence of CB The CB samples, before and after modification, were subjected to analysis of scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). It was possible verify that the partial transformation of bacterial cellulose by inserting a layer of thermoplastic polymer on its surface occurred efficiently, obtaining a biphasic monocomponent composite material. (author)

  7. Arduino-based automation of a DNA extraction system.

    Science.gov (United States)

    Kim, Kyung-Won; Lee, Mi-So; Ryu, Mun-Ho; Kim, Jong-Won

    2015-01-01

    There have been many studies to detect infectious diseases with the molecular genetic method. This study presents an automation process for a DNA extraction system based on microfluidics and magnetic bead, which is part of a portable molecular genetic test system. This DNA extraction system consists of a cartridge with chambers, syringes, four linear stepper actuators, and a rotary stepper actuator. The actuators provide a sequence of steps in the DNA extraction process, such as transporting, mixing, and washing for the gene specimen, magnetic bead, and reagent solutions. The proposed automation system consists of a PC-based host application and an Arduino-based controller. The host application compiles a G code sequence file and interfaces with the controller to execute the compiled sequence. The controller executes stepper motor axis motion, time delay, and input-output manipulation. It drives the stepper motor with an open library, which provides a smooth linear acceleration profile. The controller also provides a homing sequence to establish the motor's reference position, and hard limit checking to prevent any over-travelling. The proposed system was implemented and its functionality was investigated, especially regarding positioning accuracy and velocity profile.

  8. Factors influencing phase-disengagement rates in solvent-extraction systems employing tertiary amine extractants

    International Nuclear Information System (INIS)

    Moyer, B.A.; McDowell, W.J.

    1981-01-01

    The primary purpose of the present investigation was to examine the effects of amine size and structure on phase disengagement. Nine commercial tertiary amines were tested together with four laboratory-quality amines for uranium extraction and both organic-continuous (OC) and aqueous-continuous (AC) phase disengagement under Amex-type conditions. Synthetic acid sulfate solutions with and without added colloidal silica and actual ore leach solutions were used as the aqueous phases. Phase disengagement results were correlated with amine size and branching and solution wetting behavior on a silicate (glass) surface. The results suggest that the performance of some Amex systems may be improved by using branched chain tertiary amine extractants of higher molecular weight than are now normally used

  9. Biphasic catalysis using amphiphilic polyphenols-chelated noble metals as highly active and selective catalysts

    Science.gov (United States)

    Mao, Hui; Yu, Hong; Chen, Jing; Liao, Xuepin

    2013-01-01

    In the field of catalysis, it is highly desired to develop novel catalysts that combine the advantages of both homogeneous and heterogeneous catalysts. Here we disclose that the use of plant pholyphenol as amphiphilic large molecule ligand/stabilizer allows for the preparation of noble metal complex and noble metal nanoparticle catalysts. These catalysts are found to be highly selective and active in aqueous-organic biphasic catalysis of cinnamaldehyde and quinoline, and can be reused at least 3 times without significant loss of activity. Moreover, the catalytic activity and reusability of the catalysts can be rationally controlled by simply adjusting the content of polyphenols in the catalysts. Our strategy may be extended to design a wide range of aqueous-organic biphasic catalysis system. PMID:23863916

  10. Biphasic catalysis using amphiphilic polyphenols-chelated noble metals as highly active and selective catalysts.

    Science.gov (United States)

    Mao, Hui; Yu, Hong; Chen, Jing; Liao, Xuepin

    2013-01-01

    In the field of catalysis, it is highly desired to develop novel catalysts that combine the advantages of both homogeneous and heterogeneous catalysts. Here we disclose that the use of plant polyphenol as amphiphilic large molecule ligand/stabilizer allows for the preparation of noble metal complex and noble metal nanoparticle catalysts. These catalysts are found to be highly selective and active in aqueous-organic biphasic catalysis of cinnamaldehyde and quinoline, and can be reused at least 3 times without significant loss of activity. Moreover, the catalytic activity and reusability of the catalysts can be rationally controlled by simply adjusting the content of polyphenols in the catalysts. Our strategy may be extended to design a wide range of aqueous-organic biphasic catalysis system.

  11. Extraction of metal ions in aqueous polyethylene glycol-inorganic salt two-phase systems in the presence of inorganic extractants: correlation between extraction behaviour and stability constants of extracted species.

    Science.gov (United States)

    Bulgariu, Laura; Bulgariu, Dumitru

    2008-07-04

    The use of aqueous polyethylene glycol-inorganic salt two-phase systems for the extraction of metal ions has a great potential due to their durability, non-toxicity and relative low cost. The aqueous phases can be easily separated by centrifugation, and the operation is possible in a range of experimental conditions. The experimental results have shown that for a given aqueous two-phase system, the extraction behaviour of metal ions in presence of inorganic extractants is mainly dependent on the stability of extracted species. In this paper we review our results obtained at metal ion extraction using inorganic extractants and discuss three major types of extraction behaviours.

  12. Simulation of equilibrium distribution data in a solvent extraction system

    International Nuclear Information System (INIS)

    Mondal, S.; Giriyalkar, A.B.; Singh, A.K.; Singh, D.K.; Hubli, R.C.

    2014-01-01

    In hydrometallurgy, solvent extraction has been proved to be the purification method to recover metal in high-pure form from impure solution. Any solvent extraction process is complex and based on some operating parameters which always lure the scientists to model them. Operating parameters like aqueous to organic volume ratio and concentration of feed are related to required number of stages for a product with specific recovery. So to determine final feed concentration or aqueous to organic volume ratio for a specific extractant concentration, one needs to carry out a number of extraction experiments tediously supported by analysis. Here an attempt is being made to model the distribution of solute between organic and aqueous phases with minimum analytical and experimental support for any system. The model can predict the effect on solvent extraction for a change in the aqueous to organic volume ratio i.e. slope of operating line, percentage loading of solvent, feed concentration, solvent concentration, number of stages and in the process it can help in optimizing conditions for the best result from a solvent extraction system. Uranium-7% TBP in dodecane system was taken up to validate the model. The predicted values of the model was tallied against uranium distribution between aqueous and organic phases in a running mixer settler. The equation for operating line i.e. straight line is derived from O/A=1.5 and considering barren organic contains 2 ppm uranium: y 1 = 0.667x 0 - .002. The extraction isotherm i.e. parabola equation came as : x 1 = 0.003y 0 2 + 0.723y 0 considering three points i.e. (0,0), (13,16.7) (uranium analysis for first stage of mixer-settler) and (25, 30.69) (feed concentration, loading capacity of solvent). Using these two equations the results that were obtained, predicted the solute distribution across different stages exactly as it is in the running mixer settler. Individual isotherms could also be drawn with the predicted results from the

  13. Stoichiometric implications of a biphasic life cycle.

    Science.gov (United States)

    Tiegs, Scott D; Berven, Keith A; Carmack, Douglas J; Capps, Krista A

    2016-03-01

    Animals mediate flows of elements and energy in ecosystems through processes such as nutrient sequestration in body tissues, and mineralization through excretion. For taxa with biphasic life cycles, the dramatic shifts in anatomy and physiology that occur during ontogeny are expected to be accompanied by changes in body and excreta stoichiometry, but remain little-explored, especially in vertebrates. Here we tested stoichiometric hypotheses related to the bodies and excreta of the wood frog (Lithobates sylvaticus) across life stages and during larval development. Per-capita rates of nitrogen (N) and phosphorus (P) excretion varied widely during larval ontogeny, followed unimodal patterns, and peaked midway through development (Taylor-Kollros stages XV and XII, respectively). Larval mass did not increase steadily during development but peaked at stage XVII and declined until the termination of the experiment at stage XXII. Mass-specific N and P excretion rates of the larvae decreased exponentially during development. When coupled with population-biomass estimates, population-level excretion rates were greatest at stages VIII-X. Percent carbon (C), N, and C:N of body tissue showed weak trends across major life stages; body P and C:P, however, increased sixfold during development from egg to adult. Our results demonstrate that intraspecific ontogenic changes in nutrient contents of excretion and body tissues can be significant, and that N and P are not always excreted proportionally throughout life cycles. These results highlight the dynamic roles that species play in ecosystems, and how the morphological and physiological changes that accompany ontogeny can influence ecosystem-level processes.

  14. Extraction of Trivalent Actinides and Lanthanides from Californium Campaign Rework Solution Using TODGA-based Solvent Extraction System

    Energy Technology Data Exchange (ETDEWEB)

    Benker, Dennis [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Delmau, Laetitia Helene [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Dryman, Joshua Cory [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-07-01

    This report presents the studies carried out to demonstrate the possibility of quantitatively extracting trivalent actinides and lanthanides from highly acidic solutions using a neutral ligand-based solvent extraction system. These studies stemmed from the perceived advantage of such systems over cationexchange- based solvent extraction systems that require an extensive feed adjustment to make a low-acid feed. The targeted feed solutions are highly acidic aqueous phases obtained after the dissolution of curium targets during a californium (Cf) campaign. Results obtained with actual Cf campaign solutions, but highly diluted to be manageable in a glove box, are presented, followed by results of tests run in the hot cells with Cf campaign rework solutions. It was demonstrated that a solvent extraction system based on the tetraoctyl diglycolamide molecule is capable of quantitatively extracting trivalent actinides from highly acidic solutions. This system was validated using actual feeds from a Cf campaign.

  15. Development of alternate extractant systems for fast reactor fuel cycle

    International Nuclear Information System (INIS)

    Vasudeva Rao, P.R.; Suresh, A.; Venkatesan, K.A.; Srinivasan, T.G.; Raj, Baldev

    2007-01-01

    Due to the limitations of TBP in processing of high burn-up, Pu-rich fast reactor fuels, there is a need to develop alternate extractants for fast reactor fuel processing. In this context, our Centre has been examining the suitability of alternate tri-alkyl phosphates. Third phase formation in the extraction of Th(IV) by TBP, tri-n-amyl phosphate (TAP) and tri-2-methyl-butyl phosphate (T2MBP) from nitric acid media has been investigated under various conditions to derive conclusions on their application for extraction of Pu at macro levels. The chemical and radiolytic degradation of tri-n-amyl-phosphate (TAP) diluted in normal paraffin hydrocarbon (NPH) in the presence of nitric acid has been investigated by the measurement of plutonium retention in organic phase. The potential application of room temperature ionic liquids (RTILs) for reprocessing of spent nuclear fuel has been explored. Extraction of uranium (VI) and palladium (II) from nitric acid medium by commercially available RTIL and tri-n-butyl phosphate solution in RTIL have been studied and the feasibility of electrodeposition of uranium as uranium oxide (UO 2 ) and palladium (II) as metallic palladium from the loaded organic phase have been demonstrated. This paper describes results of the above studies and discusses the suitability of the systems for fast reactor fuel reprocessing. (authors)

  16. Extraction of L-Aspartic Acid with Reverse Micelle System

    Directory of Open Access Journals (Sweden)

    Özlem AYDOĞAN

    2009-02-01

    Full Text Available The aim of this study is to investigate the extraction L-aspartic acid which is a hydrophobic amino acid with reverse micelle system. Production of amino acids by fermentation has been more important in recent years. These amino acids are obtained in dilute aqueous solutions and have to be separated from excess substrate, inorganic salts and by-products. Recently, separation of amino acids from fermentation media by reverse micelle extraction has received a great deal of attention. In this study, reverse micelle phase includes aliquat-336 as a surfactant, 1-decanol as a co-surfactant and isooctane as an apolar solvent. Experiments were performed at 150 rpm stirring rate, at 30 oC, for 30 min extraction time with equal volumes of reverse micelle and aqueous phases. Concentration of L-aspartic acid was analyzed by liquid chromatography (HPLC. The extraction yield increased with increasing pH and aliquat-336 concentration and with decreasing initial amino acid concentration. Maximum ekstraction yield (68 % was obtained at pH of 12, surfactant concentration of 200 mM and an initial amino acid concentration of 5 mM.

  17. Nitric oxide interacts with salicylate to regulate biphasic ethylene production during the hypersensitive response.

    Science.gov (United States)

    Mur, Luis A J; Laarhoven, Lucas J J; Harren, Frans J M; Hall, Michael A; Smith, Aileen R

    2008-11-01

    C(2)H(4) is associated with plant defense, but its role during the hypersensitive response (HR) remains largely uncharacterized. C(2)H(4) production in tobacco (Nicotiana tabacum) following inoculation with HR-eliciting Pseudomonas syringae pathovars measured by laser photoacoustic detection was biphasic. A first transient rise (C(2)H(4)-I) occurred 1 to 4 h following inoculation with HR-eliciting, disease-forming, and nonpathogenic strains and also with flagellin (flg22). A second (avirulence-dependent) rise, at approximately 6 h (C(2)H(4)-II), was only seen with HR-eliciting strains. Tobacco leaves treated with the C(2)H(4) biosynthesis inhibitor, aminoethoxyvinylglycine, suggested that C(2)H(4) influenced the kinetics of a HR. Challenging salicylate hydroxylase-expressing tobacco lines and tissues exhibiting systemic acquired resistance suggested that C(2)H(4) production was influenced by salicylic acid (SA). Disrupted expression of a C(2)H(4) biosynthesis gene in salicylate hydroxylase tobacco plants implicated transcriptional control as a mechanism through which SA regulates C(2)H(4) production. Treating leaves to increase oxidative stress or injecting with SA initiated monophasic C(2)H(4) generation, but the nitric oxide (NO) donor sodium nitroprusside initiated biphasic rises. To test whether NO influenced biphasic C(2)H(4) production during the HR, the NO synthase inhibitor N(G)-nitro-L-arginine methyl ester was coinoculated with the avirulent strain of P. syringae pv phaseolicola into tobacco leaves. The first transient C(2)H(4) rise appeared to be unaffected by N(G)-nitro-L-arginine methyl ester, but the second rise was reduced. These data suggest that NO and SA are required to generate the biphasic pattern of C(2)H(4) production during the HR and may influence the kinetics of HR formation.

  18. Large change in voltage at phase reversal improves biphasic defibrillation thresholds. Parallel-series mode switching.

    Science.gov (United States)

    Yamanouchi, Y; Mowrey, K A; Nadzam, G R; Hills, D G; Kroll, M W; Brewer, J E; Donohoo, A M; Wilkoff, B L; Tchou, P J

    1996-10-01

    Multiple factors contribute to an improved defibrillation threshold of biphasic shocks. The leading-edge voltage of the second phase may be an important factor in reducing the defibrillation threshold. We tested two experimental biphasic waveforms with large voltage changes at phase reversal. The phase 2 leading-edge voltage was twice the phase 1 trailing-edge voltage. This large voltage change was achieved by switching two capacitors from parallel to series mode at phase reversal. Two capacitors were tested (60/15 microfarads [microF] and 90/22.5 microF) and compared with two control biphasic waveforms for which the phase 1 trailing-edge voltage equaled the phase 2 leading-edge voltage. The control waveforms were incorporated into clinical (135/135 microF) or investigational devices (90/90 microF). Defibrillation threshold parameters were evaluated in eight anesthetized pigs by use of a nonthoracotomy transvenous lead to a can electrode system. The stored energy at the defibrillation threshold (ion joules) was 8.2 +/- 1.5 for 60/15 microF (P voltage changes at phase reversal caused by parallel-series mode switching appeared to improve the ventricular defibrillation threshold in a pig model compared with a currently available biphasic waveform. The 60/15-microF capacitor performed as well as the 90/ 22.5-microF capacitor in the experimental waveform. Thus, smaller capacitors may allow reduction in device size without sacrificing defibrillation threshold energy requirements.

  19. PCA Fault Feature Extraction in Complex Electric Power Systems

    Directory of Open Access Journals (Sweden)

    ZHANG, J.

    2010-08-01

    Full Text Available Electric power system is one of the most complex artificial systems in the world. The complexity is determined by its characteristics about constitution, configuration, operation, organization, etc. The fault in electric power system cannot be completely avoided. When electric power system operates from normal state to failure or abnormal, its electric quantities (current, voltage and angles, etc. may change significantly. Our researches indicate that the variable with the biggest coefficient in principal component usually corresponds to the fault. Therefore, utilizing real-time measurements of phasor measurement unit, based on principal components analysis technology, we have extracted successfully the distinct features of fault component. Of course, because of the complexity of different types of faults in electric power system, there still exists enormous problems need a close and intensive study.

  20. Stable emulsions in extraction systems containing zirconium and silicic acid

    International Nuclear Information System (INIS)

    Sinegribova, O.A.; Chizhevskaya, S.V.; Kotenko, A.A.

    1989-01-01

    The effect of zirconium nitrate compound nature and silicic acid on the rate of emulsions stratification in extraction systems depending on the components concentration, solution acidity, its past history, is studied. It is stated that stable multinuclear zirconium compounds have an influence on formation of stable emulsions in systems containing silicic acid. On the basis of results of chemical analysis and properties of interphase precipitates, being part of stable emulsion, suppositions on mechanism of interaction of zirconium nitrate compounds with silicic acid β-form are made

  1. Model-Based Extracted Water Desalination System for Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Dees, Elizabeth M. [General Electric Global Research Center, Niskayuna, NY (United States); Moore, David Roger [General Electric Global Research Center, Niskayuna, NY (United States); Li, Li [Pennsylvania State Univ., University Park, PA (United States); Kumar, Manish [Pennsylvania State Univ., University Park, PA (United States)

    2017-05-28

    Over the last 1.5 years, GE Global Research and Pennsylvania State University defined a model-based, scalable, and multi-stage extracted water desalination system that yields clean water, concentrated brine, and, optionally, salt. The team explored saline brines that ranged across the expected range for extracted water for carbon sequestration reservoirs (40,000 up to 220,000 ppm total dissolved solids, TDS). In addition, the validated the system performance at pilot scale with field-sourced water using GE’s pre-pilot and lab facilities. This project encompassed four principal tasks, in addition to Project Management and Planning: 1) identify a deep saline formation carbon sequestration site and a partner that are suitable for supplying extracted water; 2) conduct a techno-economic assessment and down-selection of pre-treatment and desalination technologies to identify a cost-effective system for extracted water recovery; 3) validate the downselected processes at the lab/pre-pilot scale; and 4) define the scope of the pilot desalination project. Highlights from each task are described below: Deep saline formation characterization The deep saline formations associated with the five DOE NETL 1260 Phase 1 projects were characterized with respect to their mineralogy and formation water composition. Sources of high TDS feed water other than extracted water were explored for high TDS desalination applications, including unconventional oil and gas and seawater reverse osmosis concentrate. Technoeconomic analysis of desalination technologies Techno-economic evaluations of alternate brine concentration technologies, including humidification-dehumidification (HDH), membrane distillation (MD), forward osmosis (FO), turboexpander-freeze, solvent extraction and high pressure reverse osmosis (HPRO), were conducted. These technologies were evaluated against conventional falling film-mechanical vapor recompression (FF-MVR) as a baseline desalination process. Furthermore, a

  2. Model-based Extracted Water Desalination System for Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Gettings, Rachel; Dees, Elizabeth

    2017-03-23

    The focus of this research effort centered around water recovery from high Total Dissolved Solids (TDS) extracted waters (180,000 mg/L) using a combination of water recovery (partial desalination) technologies. The research goals of this project were as follows: 1. Define the scope and test location for pilot-scale implementation of the desalination system, 2.Define a scalable, multi-stage extracted water desalination system that yields clean water, concentrated brine, and, salt from saline brines, and 3. Validate overall system performance with field-sourced water using GE pre-pilot lab facilities. Conventional falling film-mechanical vapor recompression (FF-MVR) technology was established as a baseline desalination process. A quality function deployment (QFD) method was used to compare alternate high TDS desalination technologies to the base case FF-MVR technology, including but not limited to: membrane distillation (MD), forward osmosis (FO), and high pressure reverse osmosis (HPRO). Technoeconomic analysis of high pressure reverse osmosis (HPRO) was performed comparing the following two cases: 1. a hybrid seawater RO (SWRO) plus HPRO system and 2. 2x standard seawater RO system, to achieve the same total pure water recovery rate. Pre-pilot-scale tests were conducted using field production water to validate key process steps for extracted water pretreatment. Approximately 5,000 gallons of field produced water was processed through, microfiltration, ultrafiltration, and steam regenerable sorbent operations. Improvements in membrane materials of construction were considered as necessary next steps to achieving further improvement in element performance at high pressure. Several modifications showed promising results in their ability to withstand close to 5,000 PSI without gross failure.

  3. Progress on the biphase turbine at Cerro Prieto

    Energy Technology Data Exchange (ETDEWEB)

    Cerini, D.; Hays, L.; Studhalter, W. [Douglas Energy Company, Placentia, CA (United States)

    1997-12-31

    The status of a Biphase turbine power plant being installed at the Cerro Prieto geothermal field is presented. The major modules for the power plant are completed except for a back pressure steam turbine. The power plant will be started in April 1997 with the Biphase turbine alone followed by the addition of the steam turbine module two months later. The current power plant performance level is 2780 kWe due to a decline in the well. An increase in power output to 4060 kWe by adding the flow from another well is planned. The addition of five Biphase power plants with a total power output of 21.2 megawatts is described.

  4. Planetary Airplane Extraction System Development and Subscale Testing

    Science.gov (United States)

    Teter, John E., Jr.

    2006-01-01

    The Aerial Regional-scale Environmental Survey (ARES) project will employ an airplane as the science platform from which to collect science data in the previously inaccessible, thin atmosphere of Mars. In order for the airplane to arrive safely in the Martian atmosphere, a number of sequences must occur. A critical element in the entry sequence at Mars is an extraction maneuver to separate the airplane quickly (in less than a second) from its protective backshell to reduce the possibility of re-contact, potentially leading to mission failure. This paper describes the development, testing, and lessons learned from building a 1/3 scale model of this airplane extraction system. This design, based on the successful Mars Exploration Rover (MER) extraction mechanism, employs a series of trucks rolling along tracks located on the surface of the central parachute can. Numerous tests using high speed video were conducted at the Langley Research Center to validate this concept. One area of concern was that that although the airplane released cleanly, a pitching moment could be introduced. While targeted for a Mars mission, this concept will enable environmental surveys by aircraft in other planetary bodies with a sensible atmosphere such as Venus or Saturn's moon, Titan.

  5. Biphasic Malignant Pleural Mesothelioma Masquerading as a Primary Skeletal Tumor

    Directory of Open Access Journals (Sweden)

    James Benjamin Gleason

    2016-01-01

    Full Text Available Biphasic malignant pleural mesothelioma is a rare malignant tumor, usually presenting as a pleural-based mass in a patient with history of chronic asbestos exposure. We herein report a case of a 41-year-old man who presented with chest pain and had a chest computed tomography (CT scan suggestive of a primary skeletal tumor originating from the ribs (chondrosarcoma or osteosarcoma, with no history of asbestos exposure. CT-guided core needle biopsies were diagnosed as malignant sarcomatoid mesothelioma. Surgical resection and chest wall reconstruction were performed, confirming the diagnosis and revealing a secondary histologic component (epithelioid, supporting the diagnosis of biphasic malignant mesothelioma.

  6. Spoken Language Understanding Systems for Extracting Semantic Information from Speech

    CERN Document Server

    Tur, Gokhan

    2011-01-01

    Spoken language understanding (SLU) is an emerging field in between speech and language processing, investigating human/ machine and human/ human communication by leveraging technologies from signal processing, pattern recognition, machine learning and artificial intelligence. SLU systems are designed to extract the meaning from speech utterances and its applications are vast, from voice search in mobile devices to meeting summarization, attracting interest from both commercial and academic sectors. Both human/machine and human/human communications can benefit from the application of SLU, usin

  7. Study on system for extracted type infrared gas analysis

    Science.gov (United States)

    Gu, Ruirui; Yao, Jun; Li, Wei; Li, Wenzhong; Zhang, Shaohua; Liu, Zhe; Wen, Qiang

    2015-12-01

    Based on the Beer-Lambert law and the characteristic IR absorption spectrum of CO, a system for extracted type infrared gas analysis has been designed and manufactured, which utilizes different absorptive degrees infrared light gain under different concentration degrees of the gas to be measured to the value of detect CO concentration, including optical path, electric circuit and gas path. A forward and backward gas detection chamber equipped with a micro flow sensor has been used in the optical path as well as a multistage high precision amplifier and filter circuit has been used in the electric circuit. The experimental results accord with the testing standard.

  8. Birch Bark Dry Extract by Supercritical Fluid Technology: Extract Characterisation and Use for Stabilisation of Semisolid Systems

    Directory of Open Access Journals (Sweden)

    Markus Armbruster

    2017-03-01

    Full Text Available Triterpene compounds like betulin, betulinic acid, erythrodiol, oleanolic acid and lupeol are known for many pharmacological effects. All these substances are found in the outer bark of birch. Apart from its pharmacological effects, birch bark extract can be used to stabilise semisolid systems. Normally, birch bark extract is produced for this purpose by extraction with organic solvents. Employing supercritical fluid technology, our aim was to develop a birch bark dry extract suitable for stabilisation of lipophilic gels with improved properties while avoiding the use of toxic solvents. With supercritical carbon dioxide, three different particle formation methods from supercritical solutions have been tested. First, particle deposition was performed from a supercritical solution in an expansion chamber. Second, the Rapid Expansion of Supercritical Solutions (RESS method was used for particle generation. Third, a modified RESS-procedure, forming the particles directly into the thereby gelated liquid, was developed. All three methods gave yields from 1% to 5.8%, depending on the techniques employed. The triterpene composition of the three extracts was comparable: all three gave more stable oleogels compared to the use of an extract obtained by organic solvent extraction. Characterizing the rheological behaviour of these gels, a faster gelling effect was seen together with a lower concentration of the extract required for the gel formation with the supercritical fluid (SCF-extracts. This confirms the superiority of the supercritical fluid produced extracts with regard to the oleogel forming properties.

  9. 16-Channel biphasic current-mode programmable charge balanced neural stimulation.

    Science.gov (United States)

    Li, Xiaoran; Zhong, Shunan; Morizio, James

    2017-08-14

    Neural stimulation is an important method used to activate or inhibit action potentials of the neuronal anatomical targets found in the brain, central nerve and peripheral nerve. The neural stimulator system produces biphasic pulses that deliver balanced charge into tissue from single or multichannel electrodes. The timing and amplitude of these biphasic pulses are precisely controlled by the neural stimulator software or imbedded algorithms. Amplitude mismatch between the anodic current and cathodic current of the biphasic pulse will cause permanently damage for the neural tissues. The main goal of our circuit and layout design is to implement a 16-channel biphasic current mode programmable neural stimulator with calibration to minimize the current mismatch caused by inherent complementary metal oxide semiconductor (CMOS) manufacturing processes. This paper presents a 16-channel constant current mode neural stimulator chip. Each channel consists of a 7-bit controllable current DAC used as sink and source current driver. To reduce the LSB quantization error and the current mismatch, an automatic calibration circuit and flow diagram is presented in this paper. There are two modes of operation of the stimulator chip-namely, stimulation mode and calibration mode. The chip also includes a digital interface used to control the stimulator parameters and calibration levels specific for each individual channel. This stimulator Application Specific Integrated Circuit (ASIC) is designed and fabricated in a 0.18 μm High-Voltage CMOS technology that allows for ±20 V power supply. The full-scale stimulation current was designed to be at 1 mA per channel. The output current was shown to be constant throughout the timing cycles over a wide range of electrode load impedances. The calibration circuit was also designed to reduce the effect of CMOS process variation of the P-channel metal oxide semiconductor (PMOS) and N-channel metal oxide semiconductor (NMOS) devices that will

  10. Chiral separation of α-cyclohexylmandelic acid enantiomers by high-speed counter-current chromatography with biphasic recognition

    Science.gov (United States)

    Tong, Shengqiang

    2010-01-01

    This work concentrates on a novel chiral separation technology named biphasic recognition applied to resolution of α-cyclohexylmandelic acid enantiomers by high-speed counter-current chromatography (HSCCC). The biphasic chiral recognition HSCCC was performed by adding lipophilic (−)-2-ethylhexyl tartrate in the organic stationary phase and hydrophilic hydroxypropyl-β-cyclodextrin in the aqueous mobile phase, which preferentially recognized the (−)-enantiomer and (+)-enantiomer, respectively. The two-phase solvent system composed of n-hexane-methyl tert-butyl ether-water (9:1:10, v/v/v) with the above chiral selectors was selected according to the partition coefficient and separation factor of the target enantiomers. Various parameters involved in the chiral separation were investigated, namely the types of the chiral selector (CS); the concentration of each chiral selector; pH of the mobile phase; and the separation temperature. The mechanism involved in this biphasic recognition chiral separation by HSCCC was discussed. Langmuirian isotherm was employed to estimate the loading limits for each chiral selector. The overall experimental results show that the HSCCC separation of enantiomer based on biphasic recognition is much more efficient than the traditional monophasic recognition chiral separation, since it utilizes the cooperation of both lipophilic and hydrophilic chiral selectors. PMID:20303497

  11. Optimized Bone Regeneration in Calvarial Bone Defect Based on Biodegradation-Tailoring Dual-shell Biphasic Bioactive Ceramic Microspheres.

    Science.gov (United States)

    Xu, Antian; Zhuang, Chen; Xu, Shuxin; He, Fuming; Xie, Lijun; Yang, Xianyan; Gou, Zhongru

    2018-02-21

    Bioceramic particulates capable of filling bone defects have gained considerable interest over the last decade. Herein, dual-shell bioceramic microspheres (CaP@CaSi@CaP, CaSi@CaP@CaSi) with adjustable beta-tricalcium phosphate (CaP) and beta-calcium silicate (CaSi) distribution were fabricated using a co-concentric capillary system enabling bone repair via a tailorable biodegradation process. The in vitro results showed the optimal concentration (1/16 of 200 mg/ml) of extracts of dual-shell microspheres could promote bone marrow mesenchymal cell (BMSC) proliferation and enhance the level of ALP activity and Alizarin Red staining. The in vivo bone repair and microsphere biodegradation in calvarial bone defects were compared using micro-computed tomography and histological evaluations. The results indicated the pure CaP microspheres were minimally resorbed at 18 weeks post-operatively and new bone tissue was limited; however, the dual-shell microspheres were appreciably biodegraded with time in accordance with the priority from CaSi to CaP in specific layers. The CaSi@CaP@CaSi group showed a significantly higher ability to promote bone regeneration than the CaP@CaSi@CaP group. This study indicates that the biphasic microspheres with adjustable composition distribution are promising for tailoring material degradation and bone regeneration rate, and such versatile design strategy is thought to fabricate various advanced biomaterials with tailorable biological performances for bone reconstruction.

  12. Soil Vapor Extraction System Optimization, Transition, and Closure Guidance

    Energy Technology Data Exchange (ETDEWEB)

    Truex, Michael J.; Becker, Dave; Simon, Michelle A.; Oostrom, Martinus; Rice, Amy K.; Johnson, Christian D.

    2013-02-08

    Soil vapor extraction (SVE) is a prevalent remediation approach for volatile contaminants in the vadose zone. A diminishing rate of contaminant extraction over time is typically observed due to 1) diminishing contaminant mass, and/or 2) slow rates of removal for contamination in low-permeability zones. After a SVE system begins to show indications of diminishing contaminant removal rate, SVE performance needs to be evaluated to determine whether the system should be optimized, terminated, or transitioned to another technology to replace or augment SVE. This guidance specifically addresses the elements of this type of performance assessment. While not specifically presented, the approach and analyses in this guidance could also be applied at the onset of remediation selection for a site as a way to evaluate current or future impacts to groundwater from vadose zone contamination. The guidance presented here builds from existing guidance for SVE design, operation, optimization, and closure from the U.S. Environmental Protection Agency, U.S. Army Corps of Engineers, and the Air Force Center for Engineering and the Environment. The purpose of the material herein is to clarify and focus on the specific actions and decisions related to SVE optimization, transition, and/or closure.

  13. The SPS Fast Extraction Kicker System in LSS6

    CERN Document Server

    Gaxiola, E; Ducimetière, L; Faure, P; Kroyer, T; Versolatto, B; Vossenberg, G

    2006-01-01

    A new fast extraction has been set up in SPS LSS6 to transfer 450 GeV/c protons as well as ions to Ring 1 of the LHC, via the transfer line TI 2. The system includes four travelling wave kicker magnets, all powered in series, energised by a single PFN generator and terminated by a short circuit. The layout and the modifications to the magnets and the high voltage circuit are described along with the impact of design choices on the performance of the system. Results from laboratory tests are reported on approaches to overcome the effects of the beam induced kicker heating observed earlier, including a beam screen in form of metallic stripes printed directly onto the ferrites and the use of high Curie temperature ferrites. Prospects for further improvements are briefly discussed.

  14. A Bayesian approach to extracting meaning from system behavior

    Energy Technology Data Exchange (ETDEWEB)

    Dress, W.B.

    1998-08-01

    The modeling relation and its reformulation to include the semiotic hierarchy is essential for the understanding, control, and successful re-creation of natural systems. This presentation will argue for a careful application of Rosen`s modeling relationship to the problems of intelligence and autonomy in natural and artificial systems. To this end, the authors discuss the essential need for a correct theory of induction, learning, and probability; and suggest that modern Bayesian probability theory, developed by Cox, Jaynes, and others, can adequately meet such demands, especially on the operational level of extracting meaning from observations. The methods of Bayesian and maximum Entropy parameter estimation have been applied to measurements of system observables to directly infer the underlying differential equations generating system behavior. This approach by-passes the usual method of parameter estimation based on assuming a functional form for the observable and then estimating the parameters that would lead to the particular observed behavior. The computational savings is great since only location parameters enter into the maximum-entropy calculations; this innovation finesses the need for nonlinear parameters altogether. Such an approach more directly extracts the semantics inherent in a given system by going to the root of system meaning as expressed by abstract form or shape, rather than in syntactic particulars, such as signal amplitude and phase. Examples will be shown how the form of a system can be followed while ignoring unnecessary details. In this sense, the authors are observing the meaning of the words rather than being concerned with their particular expression or language. For the present discussion, empirical models are embodied by the differential equations underlying, producing, or describing the behavior of a process as measured or tracked by a particular variable set--the observables. The a priori models are probability structures that

  15. Biphasic Clinical Course Among Kenyan Children With Cerebral ...

    African Journals Online (AJOL)

    Biphasic Clinical Course Among Kenyan Children With Cerebral Malaria. ... African Journal of Neurological Sciences ... Method We undertook a retrospective study of children admitted to Kilifi District Hospital with a history of impaired consciousness and Falciparum infection between January 1994 and December 2004.

  16. Biphasic Clinical Course Among Kenyan Children With Cerebral ...

    African Journals Online (AJOL)

    Background Cerebral malaria is the most severe neurological complication of Falciparum malaria. It is associated with a significant risk of death and neurological sequelae. A biphasic clinical picture is associated with an even greater risk of neurological sequelae. Objective To examine the incidence and clinical ...

  17. Evaluation of degree of readsorption of radionuclides during sequential extraction in soil: comparison between batch and dynamic extraction systems

    DEFF Research Database (Denmark)

    Petersen, Roongrat; Hansen, Elo Harald; Hou, Xiaolin

    developed in our laboratory for heavy metal fractionation has shown the reduction of readsorption problem in comparison with the batch techniques. Moreover, the system shows many advantages over the batch system such as speed of extraction, simple procedure, fully automatic, less risk of contamination......Sequential extraction techniques have been widely used to fractionate metals in solid samples (soils, sediments, solid wastes, etc.) due to their leachability. The results are useful for obtaining information about bioavailability, potential mobility and transport of element in natural environments....... However, the techniques have an important problem with redistribution as a result of readsorption of dissolved analytes onto the remaining solids phases during extraction. Many authors have demonstrated the readsorption problem and inaccuracy from it. In our previous work, a dynamic extraction system...

  18. Central Nervous System Effects of Ginkgo Biloba, a Plant Extract.

    Science.gov (United States)

    Itil, Turan M.; Eralp, Emin; Tsambis, Elias; Itil, Kurt Z.; Stein, Ulrich

    1996-01-01

    Extracts of Ginkgo biloba (EGb) are among the most prescribed drugs in France and Germany. EGb is claimed to be effective in peripheral arterial disorders and in "cerebral insufficiency." The mechanism of action is not yet well understood. Three of the ingredients of the extract have been isolated and found to be pharmacologically active, but which one alone or in combination is responsible for clinical effects is unknown. The recommended daily dose (3 x 40 mg extract) is based more on empirical data than on clinical dose-findings studies. However, despite these, according to double-blind, placebo-controlled clinical trials, EGb has therapeutic effects, at least, on the diagnostic entity of "cerebral insufficiency," which is used in Europe as synonymous with early dementia. To determine whether EGb has significant pharmacological effects on the human brain, a pharmacodynamic study was conducted using the Quantitative Pharmacoelectroencephalogram (QPEEG(R)) method. It was established that the pharmacological effects (based on a predetermined 7.5--13.0-Hz alpha frequency band in a computer-analyzed electroencephalogram = CEEG(R)) of EGb on the central nervous system (CNS) are significantly different than placebo, and the high and low doses could be discriminated from each other. The 120-mg, but particularly the 240-mg, single doses showed the most consistent CNS effects with an earlier onset (1 h) and longer duration (7 h). Furthermore, it was established that the electrophysiological effects of EGb in CNS are similar to those of well-known cognitive activators such as "nootropics" as well as tacrine, the only marketed "antidementia" drug currently available in the United States.

  19. [A minimally invasive extraction technique using Benex Extraction System in flapless immediate implant placement in anterior teeth].

    Science.gov (United States)

    Ren, Shu-Xin; Hu, Xiu-Lian; Li, Jian-Hui; Jiang, Xi; Lin, Ye

    2016-06-01

    To evaluate the feasibility and clinical outcomes of an atraumatic extraction technique using Benex Extraction System in flapless immediate implant placement in anterior teeth. Twenty-five patients with single hopeless anterior maxillary teeth were enrolled in the study. The involved teeth were extracted using Benex Extraction System and implants were immediately placed in a flapless way. Healing abutments were connected immediately. After 4-6 months of healing, screw-retained implant temporary crowns were used to reshape the peri-implant gingiva. Permanent restorations were delivered 3 months later. Extraction time was recorded and the technique feasibility was evaluated using visual analogue scale (VAS). Peri-implant marginal bone resorption was measured in X- ray films after loading for 1 year later. Pink esthetic score (PES) was checked to evaluate the gingival esthetics. Questionnaire was delivered and collected to assess patients' satisfaction on surgical experience and esthetic outcomes. SPSS 13.0 software package was used for statistical analysis. Twenty-five implants osseointegrated successfully. The marginal bone resorption was (0.21±0.23) mm and PES was 8.8±1.19 after loading for 1 year. The mean extraction time was 6.87 minutes and the VAS was 3.32. All patients were satisfied with the final esthetic outcomes and felt comfort during surgery. According to the limited data in the study, Benex extraction System is a convenient, atraumatic and predictable technique during flapless immediate implant placement in anterior teeth.

  20. Differential Biphasic Transcriptional Host Response Associated with Coevolution of Hemagglutinin Quasispecies of Influenza A Virus

    Directory of Open Access Journals (Sweden)

    Himanshu Manchanda

    2016-08-01

    Full Text Available Severe influenza associated with strong symptoms and lung inflammation can be caused by intra-host evolution of quasispecies with aspartic acid or glycine in hemagglutinin position 222 (HA-222D/G; H1 numbering. To gain insights into the dynamics of host response to this coevolution and to identify key mechanisms contributing to copathogenesis, the lung transcriptional response of BALB/c mice infected with an A(H1N1pdm09 isolate consisting HA-222D/G quasispecies was analyzed from day 1 to 12 post infection (p.i. At day 2 p.i. 968 differentially expressed genes (DEGs were detected. The DEG number declined to 359 at day 4 and reached 1001 at day 7 p.i. prior to recovery. Interestingly, a biphasic expression profile was shown for the majority of these genes. Cytokine assays confirmed these results on protein level exemplarily for two key inflammatory cytokines, interferon gamma and interleukin 6. Using a reverse engineering strategy, a regulatory network was inferred to hypothetically explain the biphasic pattern for selected DEGs. Known regulatory interactions were extracted by Pathway Studio 9.0 and integrated during network inference. The hypothetic gene regulatory network revealed a positive feedback loop of Ifng, Stat1, and Tlr3 gene signaling that was triggered by the HA-G222 variant and correlated with a clinical symptom score indicating disease severity.

  1. Development of Systems Engineering Model for Spent Fuel Extraction Process

    International Nuclear Information System (INIS)

    Sun, Lijian; Royyuru, Haritha; Hsieh, Hsuan-Tsung 'Sean'; Chen, Yitung; Clarksean, Randy; Vandegrift, George; Copple, Jackie; Laidler, James

    2004-01-01

    The mission of the Transmutation Research Program (TRP) at University of Nevada, Las Vegas (UNLV) is to establish a nuclear engineering test bed that can carry out effective transmutation and advanced reactor research and development effort. The Nevada Center for Advanced Computational Methods (NCACM) at UNLV is currently developing the systems engineering model, TRPSEMPro (Transmutation Research Program System Engineering Model Project, that provides process optimization through the automatic adjustment on input parameters, such as feed compositions, stages, flow rates, etc., based on the extraction efficiency of components and concerned output factors. An object-oriented programming (OOP) is considered. Such systems engineering model consists of task manager, task integration and solution monitor modules. A MS SQL server database is implemented for managing data flow from optimization processing. Task manager coordinates and interacts with other two modules. Task integration module works as a flowsheet constructor that builds task hierarchy, input parameter values and constrains. Task solution monitor component presents both in-progress and final outputs in tabulated and graphical formats. The system can monitor parameter justification outputs from optimization toolbox developed by Mathworks' MatLab commercial software. While initial parameter constraint identifications for using optimization process is tedious and time-consuming, the interface also provides a multiple-run process that executes a design matrix without invoking any optimization module. Experimental reports can be flexibly generated through database query and formatting. (authors)

  2. System and method for free-boundary surface extraction

    KAUST Repository

    Algarni, Marei

    2017-10-26

    A method of extracting surfaces in three-dimensional data includes receiving as inputs three-dimensional data and a seed point p located on a surface to be extracted. The method further includes propagating a front outwardly from the seed point p and extracting a plurality of ridge curves based on the propagated front. A surface boundary is detected based on a comparison of distances between adjacent ridge curves and the desired surface is extracted based on the detected surface boundary.

  3. Effect of changing capacitors between phases of a biphasic defibrillation shock.

    Science.gov (United States)

    Walcott, G P; Rollins, D L; Smith, W M; Ideker, R E

    1996-06-01

    In this study, we examined the effect of changing capacitor values between phases of a biphasic waveform with the goal of lowering leading edge voltage (LEV), total delivered energy (TDE), and total stored energy (TSE). Defibrillation thresholds were determined in 18 open-chest swine using epicardial patch electrodes. In part I, three combinations of capacitors were tested: 150:150 microF; 150:300 microF; and 300:150 microF. Waveform durations were 6/0, 6/2, 6/4, 6/6, and 6/8 ms. In part II, phase 1 capacitance was 150 microF. Three phase 2 capacitance values were used: 150 microF; 75 microF; and 37.5 microF. Phase 2 LEV was a multiple of phase 1 trailing edge voltage: x 0.5; x 0.75; x 1; x 2; x 3; and x 4. A 3.5/2.0 ms biphasic waveform was used. In part III, thresholds were determined for two sets of capacitor values, which can be created by switching a pair of capacitors from in parallel to in series, 150:37.5 microF and 300:75 microF, and nine waveform durations, 4/0, 4/2, 4/4, 6/0, 6/3, 6/6, 8/0, 8/4 and 8/8 ms. In part I, the 300:150 microF system defibrillated with the lowest LEV, TDE and TSE were not different for any of the biphasic waveforms tested except for the 6/8 ms, which was higher. In part II, there was no difference in LEV among any of the three phase 2 capacitor values. LEV was lowest for the x 2, x 3, x 4 multipliers. Peak voltage was lowest for the x 1 and x 2 multipliers. TDE was lowest for the x 0.5, x 0.75, x 1, and x 2 multipliers. In part III, the 300:75 microF system defibrillated at a lower LEV than did the 150:37.5 microF system. The 150:37.5 microF system defibrillated at a lower total delivered energy than did the 300:75 microF. These results suggest that defibrillation can be accomplished with lower LEV, TDE, and TSE if two capacitors are switched from a parallel configuration to a series configuration between phases of the biphasic waveform.

  4. Biphasic catalytic conversion of fructose by continuous hydrogenation of HMF over a hydrophobic ruthenium catalyst.

    Science.gov (United States)

    Yang, Yanliang; Du, Zhongtian; Ma, Jiping; Lu, Fang; Zhang, Junjie; Xu, Jie

    2014-05-01

    The production of chemicals directly from sugars is an important step in biomass conversion. Herein, tetrahydro-2,5-furandimethanol (THFDM), obtained from fructose, is formed by using a combination of acid and hydrophobic Ru/SiO2 in a water/cyclohexane biphasic system. Two key factors enable the high selectivity towards THFDM: modifying the hydrogenation catalyst so that it has hydrophobic properties, and the continuous hydrogenation of generated 5-(hydroxymethyl)furfural in the cyclohexane phase. Moreover, the selectivity towards THFDM is found to depend strongly on the acid catalyst used. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Technology Demonstration Summary: Terra Vac In Situ Vacuum Extraction System, Groveland, Massachusetts

    Science.gov (United States)

    Terra Vac Inc's vacuum extraction system was demonstrated at the Valley Manufactured Products Company, Inc., site in Groveland, Massachusetts. The property is part of the Groveland Wells Superfund site and is contaminated mainly by trichloroethylene (TCE). Vacuum extraction...

  6. Prednisolone multicomponent nanoparticle preparation by aerosol solvent extraction system.

    Science.gov (United States)

    Moribe, Kunikazu; Fukino, Mika; Tozuka, Yuichi; Higashi, Kenjirou; Yamamoto, Keiji

    2009-10-01

    Prednisolone nanoparticles were prepared in the presence of a hydrophilic polymer and a surfactant by the aerosol solvent extraction system (ASES). A ternary mixture of prednisolone, polyethylene glycol (PEG), and sodium dodecyl sulfate (SDS) dissolved in methanol was sprayed through a nozzle into the reaction vessel filled with supercritical carbon dioxide. After the ASES process was repeated, precipitates of the ternary components were obtained by depressurizing the reaction vessel. When a methanolic solution of prednisolone/PEG 4000/SDS at a weight ratio of 1:6:2 was sprayed under the optimized ASES conditions, the mean particle size of prednisolone obtained after dispersing the precipitates in water was observed to be ca. 230 nm. Prednisolone nanoparticles were not obtained by the binary ASES process for prednisolone, in the presence of either PEG or SDS. Furthermore, ternary cryogenic cogrinding, as well as solvent evaporation, was not effective for the preparation of prednisolone nanoparticles. As the ASES process can be conducted under moderate temperature conditions, the ASES process that was applied to the ternary system appeared to be one of the most promising methods for the preparation of drug nanoparticles using the multicomponent system.

  7. Review of biphasic insulin aspart in the treatment of type 1 and 2 diabetes

    Directory of Open Access Journals (Sweden)

    Nazia Raja-Khan

    2008-01-01

    Full Text Available Nazia Raja-Khan, Sarah S Warehime, Robert A GabbayDivision of Endocrinology, Diabetes, and Metabolism, Penn State Institute for Diabetes and Obesity, Pennsylvania State University College of Medicine, Hershey, Pennsylvania, USABackground: Insulin is an effective treatment for achieving glycemic control and preventing complications in patients with diabetes. In order to make insulin therapy more acceptable to patients, newer formulations of insulin have been developed, such as biphasic insulins. Biphasic insulins conveniently provide both prandial and basal insulin in a single injection. One of the most well-studied biphasic insulins is biphasic insulin aspart 70/30.Objective: Our goal was to review the current literature on the safety and efficacy of biphasic insulin aspart in type 1 and type 2 diabetes.Methods: A MEDLINE search was conducted using the terms “biphasic insulin aspart” to identify clinical studies and reviews.Results: Biphasic insulin aspart more effectively reduces post-prandial glucose compared to other biphasic insulins and basal insulins. Compared to biphasic insulin aspart, fasting glucose levels are lower with NPH, similar with glargine, and similar or lower with biphasic human insulin. Treat-to-target trials have shown that a goal HbA1c below 6.5 or 7% can be achieved with biphasic insulin aspart. The risk of hypoglycemia is similar to or less than that seen with other biphasic insulins or NPH insulin.Conclusion: Biphasic insulin aspart 70/30 is a safe and effective treatment option for patients with diabetes.Keywords: biphasic insulin aspart, insulin, diabetes

  8. Binary Solvent Extraction System and Extraction Time Effects on Phenolic Antioxidants from Kenaf Seeds (Hibiscus cannabinus L.) Extracted by a Pulsed Ultrasonic-Assisted Extraction

    OpenAIRE

    Yu Hua Wong; Hwee Wen Lau; Chin Ping Tan; Kamariah Long; Kar Lin Nyam

    2014-01-01

    The aim of this study was to determine the best parameter for extracting phenolic-enriched kenaf (Hibiscus cannabinus L.) seeds by a pulsed ultrasonic-assisted extraction. The antioxidant activities of ultrasonic-assisted kenaf seed extracts (KSE) were determined by a 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging capacity assay, 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) radical scavenging assay, β -carotene bleaching inhibition assay, and ferric reducing antioxi...

  9. A Lagrange multiplier mixed finite element formulation for three-dimensional contact of biphasic tissues.

    Science.gov (United States)

    Yang, Taiseung; Spilker, Robert L

    2007-06-01

    A three-dimensional (3D) contact finite element formulation has been developed for biological soft tissue-to-tissue contact analysis. The linear biphasic theory of Mow, Holmes, and Lai (1984, J. Biomech., 17(5), pp. 377-394) based on continuum mixture theory, is adopted to describe the hydrated soft tissue as a continuum of solid and fluid phases. Four contact continuity conditions derived for biphasic mixtures by Hou et al. (1989, ASME J. Biomech. Eng., 111(1), pp. 78-87) are introduced on the assumed contact surface, and a weighted residual method has been used to derive a mixed velocity-pressure finite element contact formulation. The Lagrange multiplier method is used to enforce two of the four contact continuity conditions, while the other two conditions are introduced directly into the weighted residual statement. Alternate formulations are possible, which differ in the choice of continuity conditions that are enforced with Lagrange multipliers. Primary attention is focused on a formulation that enforces the normal solid traction and relative fluid flow continuity conditions on the contact surface using Lagrange multipliers. An alternate approach, in which the multipliers enforce normal solid traction and pressure continuity conditions, is also discussed. The contact nonlinearity is treated with an iterative algorithm, where the assumed area is either extended or reduced based on the validity of the solution relative to contact conditions. The resulting first-order system of equations is solved in time using the generalized finite difference scheme. The formulation is validated by a series of increasingly complex canonical problems, including the confined and unconfined compression, the Hertz contact problem, and two biphasic indentation tests. As a clinical demonstration of the capability of the contact analysis, the gleno-humeral joint contact of human shoulders is analyzed using an idealized 3D geometry. In the joint, both glenoid and humeral head

  10. Intervertebral Disc Tissue Engineering with Natural Extracellular Matrix-Derived Biphasic Composite Scaffolds.

    Directory of Open Access Journals (Sweden)

    Baoshan Xu

    Full Text Available Tissue engineering has provided an alternative therapeutic possibility for degenerative disc diseases. However, we lack an ideal scaffold for IVD tissue engineering. The goal of this study is to fabricate a novel biomimetic biphasic scaffold for IVD tissue engineering and evaluate the feasibility of developing tissue-engineered IVD in vitro and in vivo. In present study we developed a novel integrated biphasic IVD scaffold using a simple freeze-drying and cross-linking technique of pig bone matrix gelatin (BMG for the outer annulus fibrosus (AF phase and pig acellular cartilage ECM (ACECM for the inner nucleus pulposus (NP phase. Histology and SEM results indicated no residual cells remaining in the scaffold that featured an interconnected porous microstructure (pore size of AF and NP phase 401.4 ± 13.1 μm and 231.6 ± 57.2 μm, respectively. PKH26-labeled AF and NP cells were seeded into the scaffold and cultured in vitro. SEM confirmed that seeded cells could anchor onto the scaffold. Live/dead staining showed that live cells (green fluorescence were distributed in the scaffold, with no dead cells (red fluorescence being found. The cell-scaffold constructs were implanted subcutaneously into nude mice and cultured for 6 weeks in vivo. IVD-like tissue formed in nude mice as confirmed by histology. Cells in hybrid constructs originated from PKH26-labeled cells, as confirmed by in vivo fluorescence imaging system. In conclusion, the study demonstrates the feasibility of developing a tissue-engineered IVD in vivo with a BMG- and ACECM-derived integrated AF-NP biphasic scaffold. As well, PKH26 fluorescent labeling with in vivo fluorescent imaging can be used to track cells and analyse cell--scaffold constructs in vivo.

  11. Biphasic liquid interface derived magnetite nanocrystals: synthesis, properties and growth mechanism

    Science.gov (United States)

    Hou, Yue; Hou, Chuanxin; Fan, Yuqi; Dang, Feng; Li, Bao-Wen

    2017-12-01

    Magnetite (Fe3O4) nanocubes were synthesized from a water-toluene biphasic liquid system. The Fe3O4 nuclei generated in aqueous phase were transferred into the toluene solution by modifying oleic acid (OLA) at the organic–inorganic interface. Well-dispersed Fe3O4 nanocubes with a size of 20 nm were prepared in this process. Octylamine was found to play a dominant role in controlling the dispersibility, morphology and particle size of nanocubes. Only alkylamine with proper chain length had effects on the morphology control in the biphasic liquid synthesis system. The remanence (7.04 emu g‑1) and coercivity (170 Oe) of the nanocubes were 3 times higher than those (the remanence and coercivity value were 2.03 emu g‑1 and 68 Oe) of irregular particles. Magnetite (Fe3O4) iron oxide nanoparticles can be used in various fields, including developing biomarker detection systems for disease diagnosis, ferrofluids, drug delivery, magnetic resonance imaging (MRI), energy storage, sensing, etc.

  12. Preparation and Characterization of Apatitic Biphasic Calcium Phosphate

    International Nuclear Information System (INIS)

    Thin Thin Nwe; Kyaw Naing; Khin Mar Tun; Nyunt Wynn

    2005-09-01

    The apatitic biphasic calcium phosphate (ABcp) consisting of hydroxyapatite (HA) and -tricalcium phosphate ( -Tcp) has been prepared by precipitation technique using slaked lime and orthophosphoric acid. The X-ray diffraction analysis of the product I (hydroxyapatite) revealed that ABcp was partially crystalline state. However, on heating at 800 C for 8 hrs, XRD pattern indicated a perfectly crystalline form of ABcp. This observation was supported by FT-IR measurement. The change in morphology regarding in the functional nature was infered by the shift in the FT-IR frequency. The optimization of the apatitic biphasic calcium phosphate was done by the variation of disodium hydrogen phosphate concentration, setting time, hardening time as well as compressive strength. The perpared cement may be used as an artificial substitution bone

  13. Comb polymer architecture and particle size effects on the behavior of biphasic nanoparticle inks for direct-write assembly

    Science.gov (United States)

    Yoshikawa, Jun

    the repulsive particle size. Additionally, we find that biphasic suspensions composed of both identical and different mean particle sizes exhibit larger φ-scaling exponents for compressive yield stress than shear yield stress, indicating that such systems become more resistant to compression with increasing φ. This observation suggests that the biphasic suspensions flowing through fine nozzles are more resistant to filter pressing. Our findings provide new insights into controlling rheological properties of suspensions, which are applicable to a broad range of colloidal processing techniques. Finally, the printing behavior of biphasic nanoparticle inks is investigated as a function of attractive-to-repulsive volume fraction and particle size ratio. Ink flow behavior is characterized by extrusion measurements, which reveals that the suspension viscosity, and, hence, pressure drop within micronozzles decrease as either the fraction or size of repulsive particles increases. We find that the shape retention of spanning filaments is improved by having a larger fraction of repulsive particles of smaller mean size, since this enhances the initial modulus recovery immediately after shear deformation. Biphasic inks composed of both identical and different mean particle sizes exhibit excellent flowability through fine nozzles compared to purely attractive inks, enabling fine-scale printing. These observations provide guidelines for optimizing the composition of biphasic inks for direct-write assembly of fine-scale, 3D structures.

  14. Biphasic products of dicalcium phosphate-rich cement with injectability and nondispersibility

    International Nuclear Information System (INIS)

    Ko, Chia-Ling; Chen, Jian-Chih; Hung, Chun-Cheng; Wang, Jen-Chyan; Tien, Yin-Chun; Chen, Wen-Cheng

    2014-01-01

    In this study, a calcium phosphate cement was developed using tetracalcium phosphate and surface-modified dicalcium phosphate anhydrous (DCPA). This developed injectable bone graft substitute can be molded to the shape of the bone cavity and set in situ through the piping system that has an adequate mechanical strength, non-dispersibility, and biocompatibility. The materials were based on the modified DCPA compositions of calcium phosphate cement (CPC), where the phase ratio of the surface-modified DCPA is higher than that of the conventional CPC for forming dicalcium phosphate (DCP)-rich cement. The composition and morphology of several calcium phosphate cement specimens during setting were analyzed via X-ray diffractometry and transmission electron microscopy coupled with an energy dispersive spectroscopy system. The compressive strength of DCP-rich CPCs was greater than 30 MPa after 24 h of immersion in vitro. The reaction of the CPCs produced steady final biphasic products of DCPs with apatite. The composites of calcium phosphate cements derived from tetracalcium phosphate mixed with surface-modified DCPA exhibited excellent mechanical properties, injectability, and interlocking forces between particles, and they also featured nondispersive behavior when immersed in a physiological solution. - Highlights: • Bone cement precursor with nanocrystals is characterized. • DCP-rich CPCs with nanocrystals exhibited biphasic product phases. • Nanocrystals in cement significantly affected the interlocking ability. • Nanocrystals in cement exhibited higher strength and anti-dispersion. • DCP-rich CPCs increase the potential of bioresorption after reaction

  15. Biphasic products of dicalcium phosphate-rich cement with injectability and nondispersibility

    Energy Technology Data Exchange (ETDEWEB)

    Ko, Chia-Ling [Advanced Medical Devices and Composites Laboratory, Department of Fiber and Composite Materials, Feng Chia University, Taichung, 407, Taiwan (China); Dental Medical Devices and Materials Research Center, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Chen, Jian-Chih [Department of Orthopaedics, Kaohsiung Medical University Hospital, Kaohsiung 807, Taiwan (China); Department of Orthopaedics, College of Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Hung, Chun-Cheng; Wang, Jen-Chyan [Dental Medical Devices and Materials Research Center, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Department of Dentistry, Kaohsiung Medical University Hospital, Kaohsiung 807, Taiwan (China); Tien, Yin-Chun [Department of Orthopaedics, Kaohsiung Medical University Hospital, Kaohsiung 807, Taiwan (China); Department of Orthopaedics, College of Medicine, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Chen, Wen-Cheng, E-mail: wencchen@fcu.edu.tw [Advanced Medical Devices and Composites Laboratory, Department of Fiber and Composite Materials, Feng Chia University, Taichung, 407, Taiwan (China)

    2014-06-01

    In this study, a calcium phosphate cement was developed using tetracalcium phosphate and surface-modified dicalcium phosphate anhydrous (DCPA). This developed injectable bone graft substitute can be molded to the shape of the bone cavity and set in situ through the piping system that has an adequate mechanical strength, non-dispersibility, and biocompatibility. The materials were based on the modified DCPA compositions of calcium phosphate cement (CPC), where the phase ratio of the surface-modified DCPA is higher than that of the conventional CPC for forming dicalcium phosphate (DCP)-rich cement. The composition and morphology of several calcium phosphate cement specimens during setting were analyzed via X-ray diffractometry and transmission electron microscopy coupled with an energy dispersive spectroscopy system. The compressive strength of DCP-rich CPCs was greater than 30 MPa after 24 h of immersion in vitro. The reaction of the CPCs produced steady final biphasic products of DCPs with apatite. The composites of calcium phosphate cements derived from tetracalcium phosphate mixed with surface-modified DCPA exhibited excellent mechanical properties, injectability, and interlocking forces between particles, and they also featured nondispersive behavior when immersed in a physiological solution. - Highlights: • Bone cement precursor with nanocrystals is characterized. • DCP-rich CPCs with nanocrystals exhibited biphasic product phases. • Nanocrystals in cement significantly affected the interlocking ability. • Nanocrystals in cement exhibited higher strength and anti-dispersion. • DCP-rich CPCs increase the potential of bioresorption after reaction.

  16. Influence of Biphasic Stimulation on Olfactory Ensheathing Cells for Neuroprosthetic Devices.

    Science.gov (United States)

    Hassarati, Rachelle T; Foster, L John R; Green, Rylie A

    2016-01-01

    The recent success of olfactory ensheathing cell (OEC) assisted regeneration of injured spinal cord has seen a rising interest in the use of these cells in tissue-engineered systems. Previously shown to support neural cell growth through glial scar tissue, OECs have the potential to assist neural network formation in living electrode systems to produce superior neuroprosthetic electrode surfaces. The following study sought to understand the influence of biphasic electrical stimulation (ES), inherent to bionic devices, on cell survival and function, with respect to conventional metallic and developmental conductive hydrogel (CH) coated electrodes. The CH utilized in this study was a biosynthetic hydrogel consisting of methacrylated poly(vinyl-alcohol) (PVA), heparin and gelatin through which poly(3,4-ethylenedioxythiophene) (PEDOT) was electropolymerised. OECs cultured on Pt and CH surfaces were subjected to biphasic ES. Image-based cytometry yielded little significant difference between the viability and cell cycle of OECs cultured on the stimulated and passive samples. The significantly lower voltages measured across the CH electrodes (147 ± 3 mV) compared to the Pt (317 ± 5 mV), had shown to influence a higher percentage of viable cells on CH (91-93%) compared to Pt (78-81%). To determine the functionality of these cells following electrical stimulation, OECs co-cultured with PC12 cells were found to support neural cell differentiation (an indirect measure of neurotrophic factor production) following ES.

  17. Influence of Biphasic Stimulation on Olfactory Ensheathing Cells for Neuroprosthetic Devices

    Directory of Open Access Journals (Sweden)

    Rachelle Therese Hassarati

    2016-10-01

    Full Text Available The recent success of olfactory ensheathing cell (OEC assisted regeneration of injured spinal cord has seen a rising interest in the use of these cells in tissue-engineered systems. Previously shown to support neural cell growth through glial scar tissue, OECs have the potential to assist neural network formation in living electrode systems to produce superior neuroprosthetic electrode surfaces. The following study sought to understand the influence of biphasic electrical stimulation (ES, inherent to bionic devices, on cell survival and function, with respect to conventional metallic and developmental conductive hydrogel (CH coated electrodes. The CH utilised in this study was a biosynthetic hydrogel consisting of methacrylated poly(vinyl-alcohol (PVA, heparin and gelatin through which poly(3,4-ethylenedioxythiophene (PEDOT was electropolymerised. OECs cultured on Pt and CH surfaces were subjected to biphasic ES. Image-based cytometry yielded little significant difference between the viability and cell cycle of OECs cultured on the stimulated and passive samples. The significantly lower voltages measured across the CH electrodes (147 ± 3 mV compared to the Pt (317 ± 5 mV, had shown to influence a higher percentage of viable cells on CH (91 - 93 % compared to Pt (78 - 81 %. To determine the functionality of these cells following electrical stimulation, OECs co-cultured with PC12 cells were found to support neural cell differentiation (an indirect measure of neurotrophic factor production following ES.

  18. Binary solvent extraction system and extraction time effects on phenolic antioxidants from kenaf seeds (Hibiscus cannabinus L.) extracted by a pulsed ultrasonic-assisted extraction.

    Science.gov (United States)

    Wong, Yu Hua; Lau, Hwee Wen; Tan, Chin Ping; Long, Kamariah; Nyam, Kar Lin

    2014-01-01

    The aim of this study was to determine the best parameter for extracting phenolic-enriched kenaf (Hibiscus cannabinus L.) seeds by a pulsed ultrasonic-assisted extraction. The antioxidant activities of ultrasonic-assisted kenaf seed extracts (KSE) were determined by a 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging capacity assay, 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) radical scavenging assay, β -carotene bleaching inhibition assay, and ferric reducing antioxidant power (FRAP) assay. Total phenolic content (TPC) and total flavonoid content (TFC) evaluations were carried out to determine the phenolic and flavonoid contents in KSE. The KSE from the best extraction parameter was then subjected to high performance liquid chromatography (HPLC) to quantify the phenolic compounds. The optimised extraction condition employed 80% ethanol for 15 min, with the highest values determined for the DPPH, ABTS, and FRAP assay. KSE contained mainly tannic acid (2302.20 mg/100 g extract) and sinapic acid (1198.22 mg/100 g extract), which can be used as alternative antioxidants in the food industry.

  19. Molecular and supramolecular speciation of monoamide extractant systems

    International Nuclear Information System (INIS)

    Ferru, G.

    2012-01-01

    DEHiBA (N,N-di-(ethyl-2-hexyl)isobutyramide, a monoamide, was chosen as selective extractant for the recovery of uranium in the first cycle of the GANEX process, which aims to realize the grouped extraction of actinides in the second step of the process. The aim of this work is an improved description of monoamide organic solutions in alkane diluent after solutes extraction: water, nitric acid and uranyl nitrate. A parametric study was undertaken to characterize species at molecular scale (by IR spectroscopy, UV-visible spectroscopy, time-resolved laser-induced fluorescence spectroscopy, and electro-spray ionisation mass spectrometry) and at supramolecular scale (by vapor pressure osmometry and small angle X-ray scattering coupled to molecular dynamic simulations). Extraction isotherms were modelled taking into account the molecular and supramolecular speciation. These works showed that the organization of the organic solution depends on the amide concentration, the nature and the concentration of the extracted solute. Three regimes can be distinguished. 1/For extractant concentration less than 0.5 mol/L, monomers are predominate species. 2/ For extractant concentrations between 0.5 and 1 mol/L, small aggregates are formed containing 2 to 4 molecules of monoamide. 3/ For more concentrated solutions (greater than 1 mol/L), slightly larger species can be formed after water or nitric acid extraction. Concerning uranyl nitrate extraction, an important and strong organization of the organic phase is observed, which no longer allows the formation of well spherical defined aggregates. At molecular scale, complexes are not sensitive to the organization of the solution: the same species are observed, regardless of the solute and extractant concentrations in organic phase. (author) [fr

  20. Biphasic-to-monophasic successive Co-assembly approach to yolk-shell structured mesoporous organosilica nanoparticles.

    Science.gov (United States)

    Dang, Meng; Teng, Zhaogang; Su, Xiaodan; Tao, Jun; Hao, Qing; Ma, Xiaobo; Zhang, Yunlei; Li, Yanjiao; Tian, Ying; Zhang, Junjie; Lu, Guangming; Wang, Lianhui

    2017-12-01

    In this work, we report a facile biphasic-to-monophasic successive co-assembly approach to synthesize yolk-shell structured mesoporous organosilica nanoparticles (MONs). The yolk-shell structured MONs possess ethane-bridged frameworks, high surface area (1023m 2 g -1 ), radially oriented mesochannels (3.8nm), large pore volume (0.99cm 3 g -1 ), and tunable diameter (147-324nm) and shell thickness (23-53nm). The biphasic-to-monophasic successive co-assembly method is intrinsically simple and requires neither sacrificial templates nor multistep coating processes. The key of the method is that the interiors of the mesostructured organosilica nanospheres grown in the biphasic system have a lower condensation degree and Si-C-C-Si species content than the outer shells formed in the monophasic system. Thus, the interior layer is attracted by OH -1 anions and dissolved in the monophasic system, forming the yolk-shell structures. In vitro cytotoxicity and haemolysis assays demonstrate that the ethane-bridged yolk-shell MONs possess excellent biocompatibility. Furthermore, the chemotherapy drug doxorubicin (DOX) is loaded into the yolk-shell MONs to kill drug-resistant MCF-7/ADR human breast cancer cells. Compared with free DOX and DOX-loaded typical MONs, the DOX-loaded yolk-shell MONs have higher chemotherapeutic efficacy against MCF-7/ADR cells, suggesting the great potential of yolk-shell MONs synthesized via the biphasic-to-monophasic successive co-assembly approach in the biomedical field. Copyright © 2017 Elsevier Inc. All rights reserved.

  1. Radiation chemical behaviour of actinides in extraction system

    International Nuclear Information System (INIS)

    Vladimirova, M.V.; Fedoseev, D.A.; Bojkova, I.A.; Milovanova, A.S.

    1984-01-01

    Pu(4) physicochemical state (valent, complex, aggregation states) in γ-irradiated (Esub(γ)=3H10sup(5) Gr) TBP solutions in dodecane in the presence of U(6) macroamounts has been studied. Pu(4) concertration in extractant constitutes 4x10 -3 - 7x10 -3 mol/l, J(6) concentration is from 2x10 -2 up to 1.25x10 -1 mol/l, HNO 3 concentration is approximately equal to 0.5 mol/l. It has been established on the base of analysis of absorption spectrum of γ-irradiated solution that a change of Pu(4) valency does not take place, and plutonium di-n-buthyl-phosphate complex is formed. A decrease of a solution optical density with a growth of γ-irradiation dose testifies on complex formation. Spectrophotometric (SP) titration of allowed one to determine effective (seeming) complexing consU(6) and Pu(4) solut ons has been carried out. SP titration tants of Pu(4) and U(6) with DBPK and some peculiarities of this complexing. Identity of qualitative and quantitative characteristics of absorption spectra of model and γ-irradiated solutions allows one to consider the latter as two-component (in an optical respect) and closed (in the absence of deposits) systems. This permits to use the Firordt equations for the calculation of Pu(4) and U(6) complex concentrations in irradiated systems. Possibility to calculate radiation yields of PU(4) complexes with di-n-buthylphosphate acid for Pu(4) concentrations -2 mol/l both in the presence of this complex and without it has been revealed

  2. Low-tilt monophasic and biphasic waveforms compared with standard biphasic waveforms in the transvenous defibrillation of ventricular fibrillation.

    Science.gov (United States)

    Bennett, Johan R; Darragh, Karen M; Walsh, Simon J; Allen, Desmond J; Scott, Michael; Stevenson, Michael; Adgey, Jennifer A A; Anderson, John M C J; Manoharan, Ganesh

    2014-03-01

    Commercially available implantable defibrillators utilize a high-tilt waveform. Studies in atrial fibrillation and transthoracic defibrillation of ventricular fibrillation (VF) have shown improved defibrillation efficacy using low-tilt (LT) waveforms. We investigated the feasibility, efficacy, and safety of a LT waveform in the transvenous defibrillation of VF and hypothesized that it would be more efficacious than standard tilted biphasic (STB) waveforms. The investigation was performed in four phases in a porcine model: an efficacy study of LT monophasic waveforms (n = 9), an efficacy study of LT biphasic waveforms (n = 9), a comparison study between the most successful LT waveforms and clinically available STB waveforms (n = 15), and a safety study (n = 9). A total of 1,056 shocks were delivered (phase 1: 288, phase 2: 288, phase 3: 480). The LT biphasic 8/4-ms waveform was significantly more likely to successfully defibrillate than the LT monophasic and STB waveforms with an odds ratio of 122.3 (95% confidence interval: 32.5, 460.2, P defibrillation threshold (E50) for the LT 8/4-ms waveform was 12.7 J compared to 43.5 J and 45.5 J for STB waveforms 6/6 ms and 8/4 ms, respectively, and 47.7 J for LT 12-ms waveform. The LT 8/4-ms waveform had no lasting detrimental effect on cardiac function, and any transient hemodynamical or biochemical changes observed were comparable to those observed with STB waveforms. LT waveforms are effective and appear safe in transvenous defibrillation in a porcine model of VF. The LT biphasic 8/4-ms waveform is more efficacious than conventional waveforms. ©2013, The Authors. Journal compilation ©2013 Wiley Periodicals, Inc.

  3. Numerical Capacitance Extraction for Large-Area Systems

    Science.gov (United States)

    Pham, Hoan Huu

    is to provide an alternative to the current methods for N-body problems involving millions of particles. (iii) A new formulation is proposed for the charge density problem. It yields integral equations of the second kind, for which efficient numerical algorithms are available. The resultant discretization matrices have improved conditioning and the convergence rate is faster. (iv) A simulator is designed and implemented for numerically extracting capacitance of multi-layered dielectric multi-conductor systems. It is used for studying capacitance associated with amorphous silicon thin-film transistors and imaging arrays.

  4. Biphasic alloplastic graft used to preserve the dimension of the edentulous ridge: an experimental study in the dog.

    Science.gov (United States)

    Lindhe, J; Araújo, M G; Bufler, M; Liljenberg, B

    2013-10-01

    Loss of teeth results in marked qualitative and quantitative alterations of the alveolar process at the edentulous site. It was observed that a graft comprised of bovine bone mineral placed in the fresh extraction socket delayed tissue modeling, but preserved the dimension of the ridge at edentulous sites. To analyze the influence of a biphasic synthetic graft on tissue modeling and remodeling during healing of extraction wounds. Five beagle dogs were used. Two premolars in the maxilla and two in the mandible were included. Full thickness flaps were elevated and the distal roots were removed. An alloplastic graft (BPCAP; α-TCP core coated with nanocrystalline biomimetic hydroxyapatite) embedded in porcine collagen was placed to fill the fresh extraction socket of the premolar sites. Flaps were replaced to cover the entrance of the extraction sockets during early healing. The extraction and grafting procedures were scheduled to allow for the study of 1, 2, and 3 months socket healing. The biopsies from the maxillary sites were decalcified, embedded in paraffin, and stained to allow the study of various aspects of hard tissue formation. The biopsies from the mandibular sites were processed for ground sectioning and used to evaluate alterations of ridge dimensions after 3 months of socket healing. It was documented that the biphasic alloplastic graft did not undergo marked resorption during tissue modeling and remodeling, but allowed large amounts of bone to form within the post-extraction site. Grafting the experimental sites with this biomaterial furthermore counteracted ridge resorption that otherwise occurs following tooth extraction. © 2012 John Wiley & Sons A/S.

  5. Biphasic electrical currents stimulation promotes both proliferation and differentiation of fetal neural stem cells.

    Directory of Open Access Journals (Sweden)

    Keun-A Chang

    2011-04-01

    Full Text Available The use of non-chemical methods to differentiate stem cells has attracted researchers from multiple disciplines, including the engineering and the biomedical fields. No doubt, growth factor based methods are still the most dominant of achieving some level of proliferation and differentiation control--however, chemical based methods are still limited by the quality, source, and amount of the utilized reagents. Well-defined non-chemical methods to differentiate stem cells allow stem cell scientists to control stem cell biology by precisely administering the pre-defined parameters, whether they are structural cues, substrate stiffness, or in the form of current flow. We have developed a culture system that allows normal stem cell growth and the option of applying continuous and defined levels of electric current to alter the cell biology of growing cells. This biphasic current stimulator chip employing ITO electrodes generates both positive and negative currents in the same culture chamber without affecting surface chemistry. We found that biphasic electrical currents (BECs significantly increased the proliferation of fetal neural stem cells (NSCs. Furthermore, BECs also promoted the differentiation of fetal NSCs into neuronal cells, as assessed using immunocytochemistry. Our results clearly show that BECs promote both the proliferation and neuronal differentiation of fetal NSCs. It may apply to the development of strategies that employ NSCs in the treatment of various neurodegenerative diseases, such as Alzheimer's and Parkinson's diseases.

  6. Optimized FIR filters for digital pulse compression of biphase codes with low sidelobes

    Science.gov (United States)

    Sanal, M.; Kuloor, R.; Sagayaraj, M. J.

    In miniaturized radars where power, real estate, speed and low cost are tight constraints and Doppler tolerance is not a major concern biphase codes are popular and FIR filter is used for digital pulse compression (DPC) implementation to achieve required range resolution. Disadvantage of low peak to sidelobe ratio (PSR) of biphase codes can be overcome by linear programming for either single stage mismatched filter or two stage approach i.e. matched filter followed by sidelobe suppression filter (SSF) filter. Linear programming (LP) calls for longer filter lengths to obtain desirable PSR. Longer the filter length greater will be the number of multipliers, hence more will be the requirement of logic resources used in the FPGAs and many time becomes design challenge for system on chip (SoC) requirement. This requirement of multipliers can be brought down by clustering the tap weights of the filter by kmeans clustering algorithm at the cost of few dB deterioration in PSR. The cluster centroid as tap weight reduces logic used in FPGA for FIR filters to a great extent by reducing number of weight multipliers. Since k-means clustering is an iterative algorithm, centroid for weights cluster is different in different iterations and causes different clusters. This causes difference in clustering of weights and sometimes even it may happen that lesser number of multiplier and lesser length of filter provide better PSR.

  7. MDCT urography: experience with a bi-phasic excretory phase examination protocol

    International Nuclear Information System (INIS)

    Meindl, Thomas; Coppenrath, Eva; Degenhart, Christoph; Reiser, Maximilian F.; Mueller-Lisse, Ullrich G.; Mueller-Lisse, Ulrike L.

    2007-01-01

    The benefit of multidetector computed tomographic urography (MDCTU) for visualising early and late excretory phase (EP) upper urinary tract (UUT) opacification has been studied. UUT opacification was retrospectively evaluated in 45 bi-phasic four-row MDCTU examinations. The UUT was divided into intrarenal collecting system (IRCS), proximal, middle and distal ureter. Two independent readers rated opacification: 1, none; 2, partial; 3, complete. Numbers of segments and percentages of UUTs at each score were calculated for each EP and two EPs combined. Results of a single EP and of combined EPs were compared by Wilcoxon matched-pairs signed-ranks. IRCS and proximal ureter were at least partially opacified in each EP in >95%. The middle ureter was at least partially opacified in the early and late EP in 85% and 93%, respectively. The distal ureter was opacified in 65% (49/75) in the early EP and in 78% (59/75) in the late EP. Combining two EPs, non-opacified distal segments decreased to 9% (7/75). Significant improvement between a single EP and combining two EPs were found for the middle and distal ureter (P < 0.03). Bi-phasic MDCTU substantially improved opacification of the middle and distal ureter. IRCS and proximal ureter are reliably opacified with one EP. (orig.)

  8. MDCT urography: experience with a bi-phasic excretory phase examination protocol

    Energy Technology Data Exchange (ETDEWEB)

    Meindl, Thomas; Coppenrath, Eva; Degenhart, Christoph; Reiser, Maximilian F.; Mueller-Lisse, Ullrich G. [University Munich, Department of Clinical Radiology, Munich (Germany); Mueller-Lisse, Ulrike L. [University Munich, Department of Urology, Munich (Germany)

    2007-10-15

    The benefit of multidetector computed tomographic urography (MDCTU) for visualising early and late excretory phase (EP) upper urinary tract (UUT) opacification has been studied. UUT opacification was retrospectively evaluated in 45 bi-phasic four-row MDCTU examinations. The UUT was divided into intrarenal collecting system (IRCS), proximal, middle and distal ureter. Two independent readers rated opacification: 1, none; 2, partial; 3, complete. Numbers of segments and percentages of UUTs at each score were calculated for each EP and two EPs combined. Results of a single EP and of combined EPs were compared by Wilcoxon matched-pairs signed-ranks. IRCS and proximal ureter were at least partially opacified in each EP in >95%. The middle ureter was at least partially opacified in the early and late EP in 85% and 93%, respectively. The distal ureter was opacified in 65% (49/75) in the early EP and in 78% (59/75) in the late EP. Combining two EPs, non-opacified distal segments decreased to 9% (7/75). Significant improvement between a single EP and combining two EPs were found for the middle and distal ureter (P < 0.03). Bi-phasic MDCTU substantially improved opacification of the middle and distal ureter. IRCS and proximal ureter are reliably opacified with one EP. (orig.)

  9. Autonomous gas chromatograph system for Thermal Enhanced Vapor Extraction System (TEVES) proof of concept demonstration

    International Nuclear Information System (INIS)

    Peter, F.J.; Laguna, G.R.

    1996-09-01

    An autonomous gas chromatograph system was designed and built to support the Thermal Enhanced Vapor Extraction System (TEVES) demonstration. TEVES is a remediation demonstration that seeks to enhance an existing technology (vacuum extraction) by adding a new technology (soil heating). A pilot scale unit was set up at one of the organic waste disposal pits at the Sandia National Laboratories Chemical Waste Landfill (CWL) in Tech Area 3. The responsibility for engineering a major part of the process instrumentation for TEVES belonged to the Manufacturing Control Subsystems Department. The primary mission of the one-of-a-kind hardware/software system is to perform on-site gas sampling and analysis to quantify a variety of volatile organic compounds (VOCs) from various sources during TEVES operations. The secondary mission is to monitor a variety of TEVES process physical parameters such as extraction manifold temperature, pressure, humidity, and flow rate, and various subsurface pressures. The system began operation in September 1994 and was still in use on follow-on projects when this report was published

  10. Effect of biphasic calcium phosphate scaffold porosities on odontogenic differentiation of human dental pulp cells.

    Science.gov (United States)

    AbdulQader, Sarah T; Rahman, Ismail A; Thirumulu, Kannan P; Ismail, Hanafi; Mahmood, Zuliani

    2016-04-01

    Calcium phosphates (CaP) of different porosities have been widely and successfully used as scaffolds with osteoblast cells for bone tissue regeneration. However, the effects of scaffold porosities on cell viability and differentiation of human dental pulp cells for dentin tissue regeneration are not well known. In this study, biphasic calcium phosphate (BCP) scaffolds of 20/80 hydroxyapatite to beta tricalcium phosphate ratio with a mean pore size of 300 μm were prepared into BCP1, BCP2, BCP3, and BCP4 of 25%, 50%, 65%, and 75% of total porosities, respectively. The extracts of these scaffolds were assessed with regard to cell viability, proliferation, and differentiation of human dental pulp cells. The high alkalinity, and more calcium and phosphate ions release that were exhibited by BCP3 and BCP4 decreased the viability and proliferation of human dental pulp cells as compared to BCP1 and BCP2. BCP2 significantly increased both cell viability and cell proliferation. However, the cells cultured with BCP3 extract revealed high alkaline phosphatase (ALP) activity and high expression of odontoblast related genes, collagen type I alpha 1, dentin matrix protein-1, and dentin sialophosphoprotein as compared to that cultured with BCP1, BCP2, and BCP4 extracts. The results highlight the effect of different scaffold porosities on the cell microenvironment and demonstrate that BCP3 scaffold of 65% porosity can support human dental pulp cells differentiation for dentin tissue regeneration. © The Author(s) 2016.

  11. Evaluation of a Unique Defibrillation Unit with Dual-Vector Biphasic Waveform Capabilities: Towards a Miniaturized Defibrillator.

    Science.gov (United States)

    Okamura, Hideo; Desimone, Christopher V; Killu, Ammar M; Gilles, Emily J; Tri, Jason; Asirvatham, Roshini; Ladewig, Dejae J; Suddendorf, Scott H; Powers, Joanne M; Wood-Wentz, Christina M; Gray, Peter D; Raymond, Douglas M; Savage, Shelley J; Savage, Walter T; Bruce, Charles J; Asirvatham, Samuel J; Friedman, Paul A

    2017-02-01

    Automated external defibrillators can provide life-saving therapies to treat ventricular fibrillation. We developed a prototype unit that can deliver a unique shock waveform produced by four independent capacitors that is delivered through two shock vectors, with the rationale of providing more robust shock pathways during emergent defibrillation. We describe the initial testing and feasibility of this unique defibrillation unit, features of which may enable downsizing of current defibrillator devices. We tested our defibrillation unit in four large animal models (two canine and two swine) under general anesthesia. Experimental defibrillation thresholds (DFT) were obtained by delivery of a unique waveform shock pulse via a dual-vector pathway with four defibrillation pads (placed across the chest). DFTs were measured and compared with those of a commercially available biphasic defibrillator (Zoll M series, Zoll Medical, Chelmsford, MA, USA) tested in two different vectors. Shocks were delivered after 10 seconds of stable ventricular fibrillation and the output characteristics and shock outcome recorded. Each defibrillation series used a step-down to failure protocol to define the defibrillation threshold. A total of 96 shocks were delivered during ventricular fibrillation in four large animals. In comparison to the Zoll M series, which delivered a single-vector, biphasic shock, the energy required for successful defibrillation using the unique dual-vector biphasic waveform did not differ significantly (P = 0.65). Our early findings support the feasibility of a unique external defibrillation unit using a dual-vector biphasic waveform approach. This warrants further study to leverage this unique concept and work toward a miniaturized, portable shock delivery system. © 2016 Wiley Periodicals, Inc.

  12. Carrier system for a plant extract or bioactive compound from a plant

    DEFF Research Database (Denmark)

    2018-01-01

    This invention relates to a carrier system for use in producing a beverage with a metered amount of plant extract or bioactive compound.......This invention relates to a carrier system for use in producing a beverage with a metered amount of plant extract or bioactive compound....

  13. Biphasic Insulin Analogues in Type 2 Diabetes: Expert Panel Recommendations

    Directory of Open Access Journals (Sweden)

    Sema Akalın

    2011-09-01

    Full Text Available Recently, the prevalence of type 2 diabetes has reached pandemic levels all over the world, and the problem is still growing. Type 2 diabetes is a progressive disease, in which insulin resistance and decrease in beta cell function accompany obesity. Early disorder, which ensues in clinical progression of the disease, is the defect of early phase insulin secretion. Patients have already lost approximately half of their beta cell reserve at the time of diagnosis. Aims of type 2 diabetes treatment are to eliminate hyperglycemia caused by insufficient insulin secretion and/or insulin resistance, to slow down beta cell destruction/depletion, to improve concomitant metabolic problems and to prevent complications. In treatment algorithms, insulin is evaluated as a replacement therapy at the following stage after life style changes (medical nutrition therapy, exercise and oral anti-diabetic drugs (OADs options. Since beta cell depletion is present at initial stages of the disease, it transforms insulin therapy into an earlier approach in treatment stages. Premixed insulin forms are one of the proposed treatment options in patients with hyperglycemia that is not controlled by OADs. These types of insulins are developed to meet both basal and postprandial insulin requirements of patients. Currently, premixed human insulin forms are replaced by analogue insulin forms, which can mimic the physiological secretion in more acceptable manner. Biphasic analogue insulin is one of the readily available pre-mixed analogue insulin forms, an example of this, Biphasic Insulin aspart 30 which is the one of the premixed analoge insulin forms, contains 30% insulin aspart and 70% protaminated insulin aspart. Consensus recommending the individualized approach in insulin therapy implies that physicians should have more detailed information about the use of different insulin forms. Although a global consensus report about initiation, titration and intensification and the use

  14. Arc detector system for extraction switches in LHC CERN

    CERN Document Server

    Dahlerup-Petersen, K; Kuper, E; Ovchar, V; Zverev, S

    2006-01-01

    The opening switches, which will be used in case of quenches or other failures in CERN’s future LHC collider to extract the large amounts of energy stored in the magnetic field of the superconducting chains of main dipoles (8 chains with 1350 MJ each) and main quadrupoles (16 chains with about 24 MJ each) consist of an array of series/parallel connected, electro-mechanical D.C. breakers, specifically designed for this particular application. During the opening process the magnet excitation current is transferred from the cluster of breakers to extraction resistors for rapid de-excitation of the magnet chain. An arc detector has been developed in order to facilitate the determination of the need for maintenance interventions on the switches. The paper describes the arc detector and highlight results from operation of the detector with a LHC pilot extraction...

  15. Estimation of acceptance of the beam extraction system of K500 superconducting cyclotron

    International Nuclear Information System (INIS)

    Paul, S.; Bhunia, U.; Agrawal, A.; Debnath, J.; Dutta, A.; Pradhan, J.; Dey, M.K.

    2015-01-01

    The extraction system of the KSOO superconducting cyclotron consists of two electrostatic deflectors and eight passive magnetic channels, spanning over an azimuthal length of 330 degrees, with radial aperture of ∼6 mm. The radial position of the elements can be varied within ±6 mm. The extraction path is within the fringing field of the cyclotron. So, different positions of the magnetic elements change the optical properties of the extraction system, as seen by the beam. Here we have approximated the entire extraction path by a series of equivalent combined function magnetic elements, having variable field and gradient for different ion species and energies. The acceptance of the extraction system at the entry of first deflector has been determined. The accelerated beam can be extracted only if its emittance matches with this acceptance aperture. The acceptance calculation also predicts the tolerance limit of the magnetic field imperfections in the acceleration zone. (author)

  16. The Streptococcus pneumoniae pilus-1 displays a biphasic expression pattern.

    Directory of Open Access Journals (Sweden)

    Gabriella De Angelis

    Full Text Available The Streptococcus pneumoniae pilus-1 is encoded by pilus islet 1 (PI-1, which has three clonal variants (clade I, II and III and is present in about 30% of clinical pneumococcal isolates. In vitro and in vivo assays have demonstrated that pilus-1 is involved in attachment to epithelial cells and virulence, as well as protection in mouse models of infection. Several reports suggest that pilus-1 expression is tightly regulated and involves the interplay of numerous genetic regulators, including the PI-1 positive regulator RlrA. In this report we provide evidence that pilus expression, when analyzed at the single-cell level in PI-1 positive strains, is biphasic. In fact, the strains present two phenotypically different sub-populations of bacteria, one that expresses the pilus, while the other does not. The proportions of these two phenotypes are variable among the strains tested and are not influenced by genotype, serotype, growth conditions, colony morphology or by the presence of antibodies directed toward the pilus components. Two sub-populations, enriched in pilus expressing or not expressing bacteria were obtained by means of colony selection and immuno-detection methods for five strains. PI-1 sequencing in the two sub-populations revealed the absence of mutations, thus indicating that the biphasic expression observed is not due to a genetic modification within PI-1. Microarray expression profile and western blot analyses on whole bacterial lysates performed comparing the two enriched sub-populations, revealed that pilus expression is regulated at the transcriptional level (on/off regulation, and that there are no other genes, in addition to those encoded by PI-1, concurrently regulated across the strains tested. Finally, we provide evidence that the over-expression of the RrlA positive regulator is sufficient to induce pilus expression in pilus-1 negative bacteria. Overall, the data presented here suggest that the observed biphasic pilus

  17. Catalytic membrane reactor for tritium extraction system from He purge

    International Nuclear Information System (INIS)

    Santucci, Alessia; Incelli, Marco; Sansovini, Mirko; Tosti, Silvano

    2016-01-01

    Highlights: • In the HCBB blanket, the produced tritium is recovered by purging with helium; membrane technologies are able to separate tritium from helium. • The paper presents the results of two experimental campaigns. • In the first, a Pd–Ag diffuser for hydrogen separation is tested at several operating conditions. • In the second, the ability of a Pd–Ag membrane reactor for water decontamination is assessed by performing isotopic swamping and water gas shift reactions. - Abstract: In the Helium Cooled Pebble Bed (HCPB) blanket concept, the produced tritium is recovered purging the breeder with helium at low pressure, thus a tritium extraction system (TES) is foreseen to separate the produced tritium (which contains impurities like water) from the helium gas purge. Several R&D activities are running in parallel to experimentally identify most promising TES technologies: particularly, Pd-based membrane reactors (MR) are under investigation because of their large hydrogen selectivity, continuous operation capability, reliability and compactness. The construction and operation under DEMO relevant conditions (that presently foresee a He purge flow rate of about 10,000 Nm 3 /h and a H 2 /He ratio of 0.1%) of a medium scale MR is scheduled for next year, while presently preliminary experiments on a small scale reactor are performed to identify most suitable operative conditions and catalyst materials. This work presents the results of an experimental campaign carried out on a Pd-based membrane aimed at measuring the capability of this device in separating hydrogen from the helium. Many operative conditions have been investigated by considering different He/H 2 feed flow ratios, several lumen pressures and reactor temperatures. Moreover, the performances of a membrane reactor (composed of a Pd–Ag tube having a wall thickness of about 113 μm, length 500 mm and diameter 10 mm) in processing the water contained in the purge gas have been measured by using

  18. Catalytic membrane reactor for tritium extraction system from He purge

    Energy Technology Data Exchange (ETDEWEB)

    Santucci, Alessia, E-mail: alessia.santucci@enea.it [ENEA for EUROfusion, Via E. Fermi 45, 00044 Frascati, Roma (Italy); Incelli, Marco [ENEA for EUROfusion, Via E. Fermi 45, 00044 Frascati, Roma (Italy); DEIM, University of Tuscia, Via del Paradiso 47, 01100 Viterbo (Italy); Sansovini, Mirko; Tosti, Silvano [ENEA for EUROfusion, Via E. Fermi 45, 00044 Frascati, Roma (Italy)

    2016-11-01

    Highlights: • In the HCBB blanket, the produced tritium is recovered by purging with helium; membrane technologies are able to separate tritium from helium. • The paper presents the results of two experimental campaigns. • In the first, a Pd–Ag diffuser for hydrogen separation is tested at several operating conditions. • In the second, the ability of a Pd–Ag membrane reactor for water decontamination is assessed by performing isotopic swamping and water gas shift reactions. - Abstract: In the Helium Cooled Pebble Bed (HCPB) blanket concept, the produced tritium is recovered purging the breeder with helium at low pressure, thus a tritium extraction system (TES) is foreseen to separate the produced tritium (which contains impurities like water) from the helium gas purge. Several R&D activities are running in parallel to experimentally identify most promising TES technologies: particularly, Pd-based membrane reactors (MR) are under investigation because of their large hydrogen selectivity, continuous operation capability, reliability and compactness. The construction and operation under DEMO relevant conditions (that presently foresee a He purge flow rate of about 10,000 Nm{sup 3}/h and a H{sub 2}/He ratio of 0.1%) of a medium scale MR is scheduled for next year, while presently preliminary experiments on a small scale reactor are performed to identify most suitable operative conditions and catalyst materials. This work presents the results of an experimental campaign carried out on a Pd-based membrane aimed at measuring the capability of this device in separating hydrogen from the helium. Many operative conditions have been investigated by considering different He/H{sub 2} feed flow ratios, several lumen pressures and reactor temperatures. Moreover, the performances of a membrane reactor (composed of a Pd–Ag tube having a wall thickness of about 113 μm, length 500 mm and diameter 10 mm) in processing the water contained in the purge gas have been

  19. Financial Information Extraction Using Pre-defined and User-definable Templates in the LOLITA System

    OpenAIRE

    Costantino, Marco; Morgan, Richard G.; Collingham, Russell J.

    1996-01-01

    This paper addresses the issue of information extraction in the financial domain within the framework of a large Natural Language Processing system: LOLITA. The LOLITA system, Large-scale Object-based Linguistic Interactor Translator and Analyser, is a general purpose natural language processing system. Different kinds of applications have been built around the system's core. One of these is the financial information extraction application, which has been designed in close contact with expert...

  20. Lithium NLP: A System for Rich Information Extraction from Noisy User Generated Text on Social Media

    OpenAIRE

    Bhargava, Preeti; Spasojevic, Nemanja; Hu, Guoning

    2017-01-01

    In this paper, we describe the Lithium Natural Language Processing (NLP) system - a resource-constrained, high- throughput and language-agnostic system for information extraction from noisy user generated text on social media. Lithium NLP extracts a rich set of information including entities, topics, hashtags and sentiment from text. We discuss several real world applications of the system currently incorporated in Lithium products. We also compare our system with existing commercial and acad...

  1. Dynamic materials accounting for solvent-extraction systems

    Energy Technology Data Exchange (ETDEWEB)

    Cobb, D.D.; Ostenak, C.A.

    1979-01-01

    Methods for estimating nuclear materials inventories in solvent-extraction contactors are being developed. These methods employ chemical models and available process measurements. Comparisons of model calculations and experimental data for mixer-settlers and pulsed columns indicate that this approach should be adequate for effective near-real-time materials accounting in nuclear fuels reprocessing plants.

  2. Dynamic materials accounting for solvent-extraction systems

    International Nuclear Information System (INIS)

    Cobb, D.D.; Ostenak, C.A.

    1979-01-01

    Methods for estimating nuclear materials inventories in solvent-extraction contactors are being developed. These methods employ chemical models and available process measurements. Comparisons of model calculations and experimental data for mixer-settlers and pulsed columns indicate that this approach should be adequate for effective near-real-time materials accounting in nuclear fuels reprocessing plants

  3. Development of an Aqueous Palm Oil Extraction System | Owolarafe ...

    African Journals Online (AJOL)

    Discovery and Innovation ... Continuous attempts have been made to re-examine the aqueous extraction of palm oil (through pit technology) and device a means of improving the technology particularly for the small-scale ... The factors considered were fruit sterilization time, variety of fruit and processing technology.

  4. Ru-Catalyzed Estragole Isomerization under Homogeneous and Ionic Liquid Biphasic Conditions

    Science.gov (United States)

    2017-01-01

    The isomerization of estragole to trans-anethole is an important reaction and is industrially performed using an excess of NaOH or KOH in ethanol at high temperatures with very low selectivity. Simple Ru-based transition-metal complexes, under homogeneous, ionic liquid (IL)-supported (biphasic) and “solventless” conditions, can be used for this reaction. The selectivity of this reaction is more sensitive to the solvent/support used than the ligands associated with the metal catalyst. Thus, under the optimized reaction conditions, 100% conversion can be achieved in the estragole isomerization, using as little as 4 × 10–3 mol % (40 ppm) of [RuHCl(CO)(PPh3)3] in toluene, reflecting a total turnover number (TON) of 25 000 and turnover frequencies (TOFs) of up to 500 min–1 at 80 °C. Using a dimeric Ru precursor, [RuCl(μ-Cl)(η3:η3-C10H16)]2, in ethanol associated with P(OEt)3, a TON of 10 000 and a TOF of 125 min–1 are obtained with 100% conversion and 99% selectivity. These two Ru catalytic systems can be transposed to biphasic IL systems by using ionic-tagged P-ligands such as 1-(3-(diphenylphosphanyl)propyl)-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide immobilized in 1-(3-hydroxypropyl)-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl) imide with up to 99% selectivity and almost complete estragole conversion. However, the reaction is much slower than that performed under solventless or homogeneous conditions. The use of ionic-tagged ligands significantly reduces the Ru leaching to the organic phase, compared to that in reactions performed under homogeneous conditions, where the catalytic system loses catalytic performance after the second recycling. Detailed kinetic investigations of the reaction catalyzed by [RuHCl(CO)(PPh3)3] indicate that a simplified kinetic model (a monomolecular reversible first-order reaction) is adequate for fitting the homogeneous reaction at 80 °C and under biphasic conditions. However, the kinetics of

  5. A construction scheme of web page comment information extraction system based on frequent subtree mining

    Science.gov (United States)

    Zhang, Xiaowen; Chen, Bingfeng

    2017-08-01

    Based on the frequent sub-tree mining algorithm, this paper proposes a construction scheme of web page comment information extraction system based on frequent subtree mining, referred to as FSM system. The entire system architecture and the various modules to do a brief introduction, and then the core of the system to do a detailed description, and finally give the system prototype.

  6. Process for preparing organoclays for aqueous and polar-organic systems

    Science.gov (United States)

    Chaiko, David J.

    2001-01-01

    A process for preparing organoclays as thixotropic agents to control the rheology of water-based paints and other aqueous and polar-organic systems. The process relates to treating low-grade clay ores to achieve highly purified organoclays and/or to incorporate surface modifying agents onto the clay by adsorption and/or to produce highly dispersed organoclays without excessive grinding or high shear dispersion. The process involves the treatment of impure, or run-of-mine, clay using an aqueous biphasic extraction system to produce a highly dispersed clay, free of mineral impurities and with modified surface properties brought about by adsorption of the water-soluble polymers used in generating the aqueous biphasic extraction system. This invention purifies the clay to greater than 95%.

  7. Development and Characterization of Biphasic Hydroxyapatite/β-TCP Cements.

    Science.gov (United States)

    Gallinetti, Sara; Canal, Cristina; Ginebra, Maria-Pau; Ferreira, J

    2014-04-01

    Biphasic calcium phosphate bioceramics composed of hydroxyapatite (HA) and β-tricalcium phosphate (β-TCP) have relevant properties as synthetic bone grafts, such as tunable resorption, bioactivity, and intrinsic osteoinduction. However, they have some limitations associated to their condition of high-temperature ceramics. In this work self-setting Biphasic Calcium Phosphate Cements (BCPCs) with different HA/β-TCP ratios were obtained from self-setting α-TCP/β-TCP pastes. The strategy used allowed synthesizing BCPCs with modulated composition, compressive strength, and specific surface area. Due to its higher solubility, α-TCP was fully hydrolyzed to a calcium-deficient HA (CDHA), whereas β-TCP remained unreacted and completely embedded in the CDHA matrix. Increasing amounts of the non-reacting β-TCP phase resulted in a linear decrease of the compressive strength, in association to the decreasing amount of precipitated HA crystals, which are responsible for the mechanical consolidation of apatitic cements. Ca 2+ release and degradation in acidic medium was similar in all the BCPCs within the timeframe studied, although differences might be expected in longer term studies once β-TCP, the more soluble phase was exposed to the surrounding media.

  8. A premolar extraction case using the Invisalign system.

    Science.gov (United States)

    Hönn, Mirjam; Göz, Gernot

    2006-09-01

    Invisalign therapy is an orthodontic treatment method using removable transparent polyurethane splints. Its applicability in extraction cases is limited. This case report documents the treatment with Invisalign of a patient in whom four premolars had to be extracted due to dental crowding. The patient's primary objective was to undergo treatment to resolve her anterior crowding as esthetically inconspicuously as possible. Diagnostic findings were: constriction of the maxillary and mandibular arch with anterior dental crowding; proclination and anteposition of the anteriors; neutroclusion with an overjet of 6 mm and an overbite of 1 mm. The radiographs showed a mesial tilt of the lower canines and premolars and a mild skeletal Class II relationship with a vertical craniofacial configuration. Treatment was initiated by extracting the four first premolars and placing the attachments (Tetric Ceram composite). After the Invisalign aligners had been worn, the anterior segment was uprighted and retracted, the crowding resolved, and the arches well-aligned. The patient's neutroclusion was maintained, physiological anterior relations in the sagittal and vertical planes were achieved, and the lower canines and premolars were uprighted. Active treatment lasted 1 year and 8 1/2 months and involved 43 maxillary and 28 mandibular aligners. Particularly in cases with an extended indication for this new treatment modality, due consideration must be given to the importance of comprehensive and meticulous diagnostics and treatment planning, and a solid grasp of the biological and mechanical fundamentals.

  9. Fully Automated Electro Membrane Extraction Autosampler for LC-MS Systems Allowing Soft Extractions for High-Throughput Applications

    DEFF Research Database (Denmark)

    Fuchs, David; Pedersen-Bjergaard, Stig; Jensen, Henrik

    2016-01-01

    was optimized for soft extraction of analytes and high sample throughput. Further, it was demonstrated that by flushing the EME-syringe with acidic wash buffer and reverting the applied electric potential, carry-over between samples can be reduced to below 1%. Performance of the system was characterized (RSD......, a complete analytical workflow of purification, separation, and analysis of sample could be achieved within only 5.5 min. With the developed system large sequences of samples could be analyzed in a completely automated manner. This high degree of automation makes the developed EME-autosampler a powerful tool...

  10. Bi-phasic hitting with constraints on impact velocity and temporal precision

    NARCIS (Netherlands)

    Caljouw, S.R.; van der Kamp, J.; Savelsbergh, G.J.P.

    2005-01-01

    The aim of the experiment was to investigate how bi-phasic hitting movements are organized to comply with both impact and temporal precision constraints. 'Bi-phasic' refers to a sequential movement with a preparatory movement away from the interception location followed by a strike phase. The

  11. Specification of an Expert system for the control of extraction units in reprocessing plants

    International Nuclear Information System (INIS)

    Jorda, A.; Charon, E.; Coppens, P.; Romet, J.L.

    1986-01-01

    Industrial operation of extraction units in reprocessing plants is very complex because the great number of chemical and hydraulic parameters to take into account. This complexity associated to the impossibility to see inside the active enclosures make difficult the operation processes, diagnosis and corrections. Management of parameters by an expert system will increase productivity and safety of solvent extraction in pulsed columns [fr

  12. Utilizing a sequential injection system furnished with an extraction microcolumn as a novel approach for executing sequential extractions of metal species in solid samples

    DEFF Research Database (Denmark)

    Chomchoei, R.; Hansen, Elo Harald; Shiowatana, J.

    2007-01-01

    This communication presents a novel approach to perform sequential extraction of elements in solid samples by using a sequential injection (SI) system incorporating a specially designed extraction microcolumn. Based on the operation of the syringe pump, different modes of extraction are potentially...... that the system entails many advantages such as being fully automated, and besides being characterised by rapidity, ease of operation and robustness, it is less prone to risks of contamination and personal errors as encountered in traditional batch systems. Moreover, improvement of the precision and accuracy...... of the chemical fractionation of metal in solids as compared with previous reports are obtained. The system ensures that extraction is performed at designated pH values. Variation of sample weight to column volume ratios do not affect the amounts of extractable metals, nor do extraction flow rates ranging from 50...

  13. Corner Feature Extraction: Techniques for Landmark Based Navigation Systems

    OpenAIRE

    Namoshe, Molaletsa; Matsebe, Oudetse; Tlale, Nkgatho

    2010-01-01

    In this paper we discussed the results of an EKF SLAM using real data logged and computed offline. One of the most important parts of the SLAM process is to accurately map the environment the robot is exploring and localize in it. To achieve this however, is depended on the precise acquirement of features extracted from the external sensor. We looked at corner detection methods and we proposed an improved version of the method discussed in section 2.1.1. It transpired that methods found in th...

  14. Development of Ingredients of the Feed-stuff for Improving Immune system using Centipede grass Extracts

    Energy Technology Data Exchange (ETDEWEB)

    Bai, Hyoungwoo; Chung, Byungyeoup; Lee, Seungsik; Lee, Sungbeom

    2013-09-15

    The purpose of the this project provides new application areas using naturally occurring flavonoids, cenetpedegrass extracts, for improving immune system and used as ingredients for feed-stuff. In order to provide the immune improving effects of centipedegrass, cell and animal experiments were carried out. Research scope includes determine the effect of centipedegrass extracts on immune functions using LPS-induced RAW cells and found that cytokines, IL-6 and IL-10, which were induced by LPS, were reduced by inhibiting phosphorylation of STAT-3, determine the effects of immune stimulating activity of centipedegrass in animals, cenetipedegrass extracts were administrated once a day for 2 weeks. After treated with LPS, immune suppressor, cytokines were down regulated, however, the cytokines in the group pretreated with centipedegrass extracts, were not down regulated as much as non treated group. The overall mechanism of immune stimulating effect of centipedegrass extracts, was that STAT-3 phosphorylation was inhibited by contipedegrass extracts.

  15. Extraction of Data from a Hospital Information System to Perform Process Mining.

    Science.gov (United States)

    Neira, Ricardo Alfredo Quintano; de Vries, Gert-Jan; Caffarel, Jennifer; Stretton, Erin

    2017-01-01

    The aim of this work is to share our experience in relevant data extraction from a hospital information system in preparation for a research study using process mining techniques. The steps performed were: research definition, mapping the normative processes, identification of tables and fields names of the database, and extraction of data. We then offer lessons learned during data extraction phase. Any errors made in the extraction phase will propagate and have implications on subsequent analyses. Thus, it is essential to take the time needed and devote sufficient attention to detail to perform all activities with the goal of ensuring high quality of the extracted data. We hope this work will be informative for other researchers to plan and execute extraction of data for process mining research studies.

  16. A hybrid system for emotion extraction from suicide notes.

    Science.gov (United States)

    Nikfarjam, Azadeh; Emadzadeh, Ehsan; Gonzalez, Graciela

    2012-01-01

    The reasons that drive someone to commit suicide are complex and their study has attracted the attention of scientists in different domains. Analyzing this phenomenon could significantly improve the preventive efforts. In this paper we present a method for sentiment analysis of suicide notes submitted to the i2b2/VA/Cincinnati Shared Task 2011. In this task the sentences of 900 suicide notes were labeled with the possible emotions that they reflect. In order to label the sentence with emotions, we propose a hybrid approach which utilizes both rule based and machine learning techniques. To solve the multi class problem a rule-based engine and an SVM model is used for each category. A set of syntactic and semantic features are selected for each sentence to build the rules and train the classifier. The rules are generated manually based on a set of lexical and emotional clues. We propose a new approach to extract the sentence's clauses and constitutive grammatical elements and to use them in syntactic and semantic feature generation. The method utilizes a novel method to measure the polarity of the sentence based on the extracted grammatical elements, reaching precision of 41.79 with recall of 55.03 for an f-measure of 47.50. The overall mean f-measure of all submissions was 48.75% with a standard deviation of 7%.

  17. System for extracting protein from a fermentation product

    Energy Technology Data Exchange (ETDEWEB)

    Lawton, Jr., John Warren; Bootsma, Jason Alan; Lewis, Stephen Michael

    2016-04-26

    A method of producing bioproducts from a feedstock in a system configured to produce ethanol and distillers grains from a fermentation product is disclosed. A system configured to process feedstock into a fermentation product and bioproducts including ethanol and meal is disclosed. A bioproduct produced from a fermentation product produced from a feedstock in a biorefining system is disclosed.

  18. Cobalt Hydroformylation of Olefins in a Biphasic System Using Ionic Liquids – Development and Reaction Optimization by a Design Experiment Approach Hydroformylation des oléfines par le cobalt en milieu liquide ionique – Développement et optimisation de la réaction par plans d’expériences

    Directory of Open Access Journals (Sweden)

    Magna L.

    2013-06-01

    Full Text Available The present paper describes the use of experimental designs (DoE in association with high throughput experimentation devices for the optimization of cobalt hydroformylation of olefins in a biphasic system using ionic liquids. The main goal of the study was to gain insight into the various factors ([Co]NAIL, L/Co, Phorg/PhNAIL, pressure and temperature and how they interact and influence the activity and selec-tivity of the catalyst. On the basis of a D-Optimal design, the study pointed out that temperature and to a less extend “Phaseorga/PhaseNAIL” ratio are the most critical parameters. These conclusions confirm to a certain extend, the initial hypothesis formulated to describe the process operation. Furthermore, this strategy in association with high throughput experimentation devices, allows to predict catalytic results in the major part of a cubic space (representing the experimental domain giving us the opportunity to determine the most suitable catalysts composition and optimal reaction conditions. Ce document décrit l’utilisation des plans d’expériences en association avec des équipements d’expérimentation haut débit, pour le développement et l’optimisation de la réaction d’hydroformylation des oléfines par le cobalt en milieu liquide ionique. L’objectif principal de ce travail était d’identifier la manière dont les différents paramètres de réaction ([Co]Li, L/Co, Phorg/PhNAIL, pression et température interagissent les uns avec les autres et d’évaluer leur influence sur l’activité et la sélectivité du catalyseur. Sur la base d’un plan d’expériences D-Optimal, cette étude fait ressortir la température et dans une moindre mesure le ratio “Phaseorga/PhaseNAIL” comme étant les paramètres critiques du procédé. Ces conclusions confirment dans une certaine mesure, les hypothèses formulées initialement pour décrire le principe de fonctionnement du procédé mis en oeuvre. Cette strat

  19. Bioactivity of marine organisms: Part 7- Effect of seaweed extract on central nervous system

    Digital Repository Service at National Institute of Oceanography (India)

    Kamat, S.Y.; Wahidullah, S.; DeSouza, L.; Naik, C.G.; Ambiye, V.; Bhakuni, D.S.; Jain, S.; Goel, A.K.; Srimal, R.C.

    Alcohol extracts of marine algae (Rhodophyceae, Phaeophyceae and Chlorophyceae) was screened for their effect on central nervous system. Of 69 species investigated 8 appeared biologically active, 6 being CNS stimulant, sites and dates of collection...

  20. Lunar South Pole space water extraction and trucking system

    International Nuclear Information System (INIS)

    Zuppero, A.; Zupp, G.; Schnitzler, B.; Larson, T.K.; Rice, J.W.

    1998-03-01

    This concept proposes to use thermal processes alone to extract water from the lunar South Pole and launch payloads to low lunar orbit. Thermal steam rockets would use water propellant for space transportation. The estimated mass of a space water tanker powered by a nuclear heated steam rocket suggests it can be designed for launch in the Space Shuttle bay. The performance depends on the feasibility of a nuclear reactor rocket engine producing steam at 1,100 degrees Kelvin, with a power density of 150 Megawatts per ton of rocket, and operating for thousands of 20 minute cycles. An example uses reject heat from a small nuclear electric power supply to melt 17,800 tons per year of lunar ice. A nuclear heated steam rocket would use the propellant water to launch and deliver 3,800 tons of water per year to a 100 km low lunar orbit

  1. Estimation of multiply digital process control system extractive distillation stability

    Directory of Open Access Journals (Sweden)

    V. S. Kudryashov

    2016-01-01

    Full Text Available An approach to stability analysis of digital control systems associated non-stationary object on the example of the rectification process. Object modeling with cross-connections and the control scheme of the described system, discrete transfer functions in the shift operators. The equations of connection for each output of the closed-loop system. To solve this problem developed an algorithm for estimating the margin of stability of multivariable digital control systems based on the discrete root criterion, comprising the following main stages: obtaining of the characteristic polynomial of the closed-loop system for each output; computation of eigenvalues of the system matrix in the state space to determine roots of the characteristic equation and the stability of the system; determination of the stability and margin of stability by the deviation of maximum module of the root from the boundary of the high variability. To obtain the characteristic polynomial of a as discrete models of controllers and channels of IP object-use the transfer function of the first order with transport delay. The simulation was performed at different parameters of the control object, which is characterized by a stable and an unstable state of the system. VA-den analysis of the numerical values of the roots and character of their location on the complex plane, which to you-water that the system is stable or unstable. To confirm the obtained results were calculated and presented dynamic characteristics of the closed-loop system under different conditions, which confirm the initial assessment, the root criterion. To determine the factor stability of multivariable digital systems is proposed to use the deviation of the maximum root of the characteristic equation from the stability boundary. The obtained results apply to the class of symmetric multivariable control objects. The approach to assessing the sustainability of multivariable system regulation can be effectively

  2. Biphasic 201thallium scintgraphy after dipyridamole in mitral valve diseases

    International Nuclear Information System (INIS)

    Schmoliner, R.; Dudczak, R.; Kronik, G.; Moesslacher, H.; Kletter, K.; Frischauf, H.

    1980-01-01

    The results of biphasic 201 thallium scintigraphy after dipyridamole i.v. could neither prove nor exclude the presence of small focal lesions in the myocardium of 17 patients with mitral valve diseases. The frequent finding of a decrease in activity in the anterolateral myocardium is probably due to a relative increase in activity in the region of the inferior wall with superimposed areas of the papillary muscle and right ventricular myocardium. If the right ventricle is visualized in stress- or redistribution images, an increase in mean pulmonary artery pressure can be accepted. According to Cohen's criteria, a grade 2 or 3 virtually proves the existence of pulmonary hypertension, a grade 1 makes this finding rather probable. The possibility of pulmonary hypertension can not be excluded if the right ventricular myocardium is not visualized. (orig.) [de

  3. Process boundaries of irreversible scCO2 -assisted phase separation in biphasic whole-cell biocatalysis.

    Science.gov (United States)

    Brandenbusch, Christoph; Glonke, Sebastian; Collins, Jonathan; Hoffrogge, Raimund; Grunwald, Klaudia; Bühler, Bruno; Schmid, Andreas; Sadowski, Gabriele

    2015-11-01

    The formation of stable emulsions in biphasic biotransformations catalyzed by microbial cells turned out to be a major hurdle for industrial implementation. Recently, a cost-effective and efficient downstream processing approach, using supercritical carbon dioxide (scCO2 ) for both irreversible emulsion destabilization (enabling complete phase separation within minutes of emulsion treatment) and product purification via extraction has been proposed by Brandenbusch et al. (2010). One of the key factors for a further development and scale-up of the approach is the understanding of the mechanism underlying scCO2 -assisted phase separation. A systematic approach was applied within this work to investigate the various factors influencing phase separation during scCO2 treatment (that is pressure, exposure of the cells to CO2 , and changes of cell surface properties). It was shown that cell toxification and cell disrupture are not responsible for emulsion destabilization. Proteins from the aqueous phase partially adsorb to cells present at the aqueous-organic interface, causing hydrophobic cell surface characteristics, and thus contribute to emulsion stabilization. By investigating the change in cell-surface hydrophobicity of these cells during CO2 treatment, it was found that a combination of catastrophic phase inversion and desorption of proteins from the cell surface is responsible for irreversible scCO2 mediated phase separation. These findings are essential for the definition of process windows for scCO2 -assisted phase separation in biphasic whole-cell biocatalysis. © 2015 Wiley Periodicals, Inc.

  4. Diagnostic accuracy of segmental enhancement inversion for diagnosis of renal oncocytoma at biphasic contrast enhanced CT: systematic review

    International Nuclear Information System (INIS)

    Schieda, Nicola; McInnes, Matthew D.F.; Cao, Lilly

    2014-01-01

    To use systematic review to evaluate the diagnostic accuracy of segmental enhancement inversion (SEI) at contrast-enhanced biphasic multi-detector computed tomography (MDCT) for the diagnosis of renal oncocytoma. Several electronic databases were searched through October 2013. Two reviewers independently selected studies that met the inclusion criteria and extracted data. Study quality was assessed with the QUADAS-2 tool. The primary 2 x 2 data were investigated with forest plot and ROC plot of sensitivity and specificity. Four studies met the inclusion criteria (307 patients). Considerable heterogeneity between studies precluded meta-analysis. Two studies from the same group of investigators demonstrated reasonable diagnostic accuracy (sensitivity 59-80 % and specificity 87-99 %), while two others did not (sensitivity 0-6 %, specificity 93-100 %). Possible reasons for this include timing of biphasic MDCT and methods of interpretation but not size of lesion. SEI is a specific imaging finding of renal oncocytoma with highly variable sensitivity. This substantial heterogeneity across studies and between institutions suggests that further validation of this imaging finding is necessary prior to application in clinical practice. (orig.)

  5. Diagnostic accuracy of segmental enhancement inversion for diagnosis of renal oncocytoma at biphasic contrast enhanced CT: systematic review

    Energy Technology Data Exchange (ETDEWEB)

    Schieda, Nicola; McInnes, Matthew D.F.; Cao, Lilly [Ottawa Hospital Research Institute, Department of Medical Imaging, Ottawa, ON (Canada)

    2014-06-15

    To use systematic review to evaluate the diagnostic accuracy of segmental enhancement inversion (SEI) at contrast-enhanced biphasic multi-detector computed tomography (MDCT) for the diagnosis of renal oncocytoma. Several electronic databases were searched through October 2013. Two reviewers independently selected studies that met the inclusion criteria and extracted data. Study quality was assessed with the QUADAS-2 tool. The primary 2 x 2 data were investigated with forest plot and ROC plot of sensitivity and specificity. Four studies met the inclusion criteria (307 patients). Considerable heterogeneity between studies precluded meta-analysis. Two studies from the same group of investigators demonstrated reasonable diagnostic accuracy (sensitivity 59-80 % and specificity 87-99 %), while two others did not (sensitivity 0-6 %, specificity 93-100 %). Possible reasons for this include timing of biphasic MDCT and methods of interpretation but not size of lesion. SEI is a specific imaging finding of renal oncocytoma with highly variable sensitivity. This substantial heterogeneity across studies and between institutions suggests that further validation of this imaging finding is necessary prior to application in clinical practice. (orig.)

  6. Bone tissue modelling and remodelling following guided bone regeneration in combination with biphasic calcium phosphate materials presenting different microporosity.

    Science.gov (United States)

    Dahlin, Christer; Obrecht, Marcel; Dard, Michel; Donos, Nikos

    2015-07-01

    The aim of this study was to investigate bone regeneration following application of a novel biphasic calcium phosphate (BCP I) composed of microstructured granules of 90% β-tricalcium phosphate (β-TCP)/10% hydroxyapatite (HA) compared to BCP non-microstructured biphasic calcium phosphate with a composite of 60% hydroxyapatite/40% β-TCP (BCP II) and a deproteinized bovine bone mineral (DBBM) at surgically created defects in the mandible of minipigs in a combined approach with guided bone regeneration (GBR). Sixteen minipigs were used for the study. Lower premolars P2, P3, P4 and first molar M1 were extracted. Following 3 months of healing, two defects with a width and depth of 7 mm were created bilaterally in the mandible. The different grafting materials were randomly placed in the created defects and covered by means of a collagen membrane. After 3 and 8 weeks, biopsies were sampled. All specimens were evaluated with descriptive histology and histomorphometric evaluations complemented by micro-CT scan analysis. All three biomaterials presented with higher bone volume at 8 weeks compared to 3 weeks (P bone formation compared to BCP II at 8 weeks (P bone formation at 8 weeks. BCP I showed significant higher amounts of newly formed bone despite a higher remaining graft volume compared to the other groups. With regard to the regenerative outcome, all the three materials can be recommended for clinical use. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  7. Extracting Process and Mapping Management for Heterogennous Systems

    Science.gov (United States)

    Hagara, Igor; Tanuška, Pavol; Duchovičová, Soňa

    2013-12-01

    A lot of papers describe three common methods of data selection from primary systems. This paper defines how to select the correct method or combinations of methods for minimizing the impact of production system and common operation. Before using any method, it is necessary to know the primary system and its databases structures for the optimal use of the actual data structure setup and the best design for ETL process. Databases structures are usually categorized into groups, which characterize their quality. The classification helps to find the ideal method for each group and thus design a solution of ETL process with the minimal impact on the data warehouse and production system.

  8. Use of Respiratory Support in the Biphase Ventilation Airway Mode in the Newborn

    Directory of Open Access Journals (Sweden)

    S. N. Koval

    2006-01-01

    Full Text Available Biphasic positive airway pressure (BIPAP (also known as DuoPAP, BiLevel, BiVent, PCV+, SPAP is a mode of ventilation with cycling variations between two continuous positive airway pressure levels. It is a mixture of pressure controlled ventilation and spontaneous breathing, which is unrestricted in each phase of the respiratory cycle. The volume displacement caused by the difference between Phigh and Plow airway pressure level. The phase time ratio (PTR — the BIPAP frequency is calculated as the ratio between the durations of the two pressure phases, a PTR greater than 1:1 is called APRV (airway pressure release ventilation. In patients with ARDS maintained spontaneous breathing with BIPAP resulted in lower venous admixture and better arterial blood oxygenation as compared with A/C. Only a few studies with BIPAP have been performed in newborn and infants until now. We studied the use of BIPAP in newborn (body mass > 3kg and randomised 40 patients with respiratory failure for ventilation with BIPAP (n=20 or conventional mechanical ventilatory support (assist-control A/C — synchronised intermittent mandatory ventilation (SIMV (n=20. The Pediatric Risk of Mortality score (PRISM were collected for each patient. Fentanyl, diazepam, GABA were used as sedatives and adjusted in accordance with the Cook scale. We compared ventilatory parameters, information pertaining to pulmonary function and oxygen delivery, cardiac output, additional descriptors of organ system functions, duration and complications of ventilation and number and dosages of sedatives administered. All the patients that we intended to ventilate with BIPAP were successfully ventilated, we can conclude that biphasic ventilatory support suitable mode of ventilation for newborn with a decreased need of analgetics and sedatives than A/C. Finally, BIPAP is an a effective safe, and easy to use for personal mode of mechanical ventilatory support in newborn. 

  9. Charge-burping theory correctly predicts optimal ratios of phase duration for biphasic defibrillation waveforms.

    Science.gov (United States)

    Swerdlow, C D; Fan, W; Brewer, J E

    1996-11-01

    For biphasic waveforms, it is accepted that the ratio of the duration of phase 2 to the duration of phase 1 (phase-duration ratio) should be theory postulates that the beneficial effects of phase 2 are maximal when it completely removes the charge delivered by phase 1. It predicts that the phase-duration ratio should be defibrillation system (tau s) exceeds the time constant of the cell membrane (tau m) but > 1 when tau s defibrillator capacitance and pathway resistance). In a canine model of transvenous defibrillation (n = 8), we determined stored-energy defibrillation thresholds (DFTs) for biphasic waveforms from conventional capacitors (140 microF. tau s = 7.1 +/- 0.8 ms) and very small capacitors (40 microF. tau s = 2.0 +/- 0.2 ms). Each capacitance was tested with phase-duration ratios of 0.5, 1, 2, and 3. The duration of phase 1 approximated the optimal monophasic waveform, 6.3 +/- 0.7 ms for 140-microF waveforms and 2.8 +/- 0.2 ms for 40-microF waveforms. For 140-microF waveforms, the DFT was lower for phase-duration ratios 1 (P = .0003). The reverse was true for 40-microF capacitors (P = .0008). There was a significant interaction between the effects of capacitance and phase-duration ratio on DFT (P = .0002). The lowest DFT for 40-microF waveforms was less than the lowest DFT for 140-microF waveforms (4.9 +/- 2.5 versus 6.4 +/- 2.4 J, P 1 for small capacitors. This supports the predictions of the charge-burping theory.

  10. A micro hot test of the Chalmers-GANEX extraction system on used nuclear fuel

    Energy Technology Data Exchange (ETDEWEB)

    Bauhn, L.; Hedberg, M.; Aneheim, E.; Ekberg, C.; Loefstroem-Engdahl, E.; Skarnemark, G. [Department of Chemical and Biological Engineering, Nuclear Chemistry, Chalmers University of Technology, Kemivaegen 4, SE-412 96 Goeteborg (Sweden)

    2013-07-01

    In the present study, a 'micro hot test' has been performed using the Chalmers-GANEX (Group Actinide Extraction) system for partitioning of used nuclear fuel. The test included a pre-extraction step using N,N-di-2- ethylhexyl-butyramide (DEHBA) in n-octanol to remove the bulk part of the uranium. This pre-extraction was followed by a group extraction of actinides using the mixture of TBP and CyMe{sub 4}-BTBP in cyclohexanone as suggested in the Chalmers-GANEX process, and a three stage stripping of the extracted actinides. Distribution ratios for the extractions and stripping were determined based on a combination of γ- and α-spectrometry, as well as ICP-MS measurements. Successful extraction of uranium, plutonium and the minor actinides neptunium, americium and curium was achieved. However, measurements also indicated that co-extraction of europium occurs to some extent during the separation. These results were expected based on previous experiments using trace concentrations of actinides and lanthanides. Since this test was only performed in one stage with respect to the group actinide extraction, it is expected that multi stage tests will give even better results. (authors)

  11. Cd(II extraction in PEG (1550–(NH42SO4 aqueous two-phase systems using halide extractants

    Directory of Open Access Journals (Sweden)

    LAURA BULGARIU

    2008-03-01

    Full Text Available The extraction of Cd(II was studied in an aqueous PEG–(NH42SO4 two-phase system, formed from a water-soluble polymer (poly(ethylene glycol, PEG and an inorganic salt ((NH42SO4, in the presence of halide ions. In the absence of a suitable extracting agent, Cd(II remains predominantly in the salt-rich phase of the extraction system. By addition of halide ions as extractants, Cd(II is extracted into the PEG-rich phase due to the formation of cadmium halide species. The efficiency of the extractants increased in the order: Cl– < Br– < I–. From the distribution coefficients determined as a function of the concentration of the halide ions, the compositions of the extracted species were assumed and the “conditional” extractions constants calculated. The experimental results indicate that the extractability of Cd(II in such extraction systems depends on the type of Cd(II halide species (which is mainly determined by the acidity of salt stock solution and of their stability.

  12. Synergy in extraction system chemistry: combining configurational entropy, film bending and perturbation of complexation

    International Nuclear Information System (INIS)

    Rey, Julien

    2016-01-01

    Separative chemistry is a pillar of technologic development in extraction, separation and selective remediation of metals and molecules. It finds its applications in the fields of electronic, renewable energy, medicine and chemistry, which require more than ever the use of 'Strategic Metals'. The liquid-liquid extraction is a separation technique that is involved in hydrometallurgical processes for the recovery of strategic metals from primary deposits, secondary and urban mines. This work is part of global vision of optimization of liquid-liquid extraction processes used in synergy, consisting in understanding the mechanisms underlying the synergy, and generalizing these mechanisms to all synergistic extraction systems. The understanding of these mechanisms underlying synergism aims at predicting and developing new synergistic extractants mixtures.To better understand the driving forces at the origin of synergistic phenomena, a suitable methodology for the characterization of supramolecular structures of extractant in the organic phase was exploited during this thesis work. The use of techniques like Small Angle Neutron/X-ray Scattering (SAXS/ANS) and interfacial tensiometry was crucial for the understanding of the synergistic mechanisms. A thermodynamical was also proposed to estimate quantitatively the key driving forces involved in the liquid-liquid extraction mechanisms. The application of these keys of comprehension helped to design a new synergistic system for the extraction of rare earths elements from phosphoric medium. (author) [fr

  13. Biologically-based signal processing system applied to noise removal for signal extraction

    Science.gov (United States)

    Fu, Chi Yung; Petrich, Loren I.

    2004-07-13

    The method and system described herein use a biologically-based signal processing system for noise removal for signal extraction. A wavelet transform may be used in conjunction with a neural network to imitate a biological system. The neural network may be trained using ideal data derived from physical principles or noiseless signals to determine to remove noise from the signal.

  14. Omnidirectional vision systems calibration, feature extraction and 3D information

    CERN Document Server

    Puig, Luis

    2013-01-01

    This work focuses on central catadioptric systems, from the early step of calibration to high-level tasks such as 3D information retrieval. The book opens with a thorough introduction to the sphere camera model, along with an analysis of the relation between this model and actual central catadioptric systems. Then, a new approach to calibrate any single-viewpoint catadioptric camera is described.  This is followed by an analysis of existing methods for calibrating central omnivision systems, and a detailed examination of hybrid two-view relations that combine images acquired with uncalibrated

  15. The setup of an extraction system coupled to a hydrogen isotopes distillation column

    International Nuclear Information System (INIS)

    Zamfirache, M.; Bornea, A.; Stefanescu, I.; Bidica, N.; Balteanu, O.; Bucur, C.

    2008-01-01

    Among the most difficult problems of cryogenic distillation one stands apart: the extraction of the heavy fraction. By an optimal design of the cycle scheme, this problem could be avoided. A 'worst case scenario' is usually occurring when the extracted fraction consists of one prevalent isotope such as hydrogen and small amounts of the other two hydrogen isotopes (deuterium and/or tritium). This situation is further complicated by two parameters of the distillation column: the extraction flow rate and the hold-up. The present work proposes the conceptual design of an extraction system associated to the cryogenic distillation column used in hydrogen separation processes. During this process, the heavy fraction (DT, T 2 ) is separated, its concentration being the highest at the bottom of the distillation column. From this place the extraction of the gaseous phase can now begin. Being filled with adsorbent, the extraction system is used to temporarily store the heavy fraction. Also the extraction system provides samples for the gas Chromatograph. The research work is focused on the existent pilot plant for tritium and deuterium separation from our institute to validate the experiments carried out until now. (authors)

  16. Simulation of the Plasma Meniscus with and without Space Charge using Triode Extraction System

    International Nuclear Information System (INIS)

    Abdel Rahman, M.M.; EI-Khabeary, H.

    2007-01-01

    In this work simulation of the singly charged argon ion trajectories for a variable plasma meniscus is studied with and without space charge for the triode extraction system by using SIMION 3D (Simulation of Ion Optics in Three Dimensions) version 7 personal computer program. Tbe influence of acceleration voltage applied to tbe acceleration electrode of the triode extraction system on the shape of the plasma meniscus has been determined. The plasma electrode is set at +5000 volt and the acceleration voltage applied to the acceleration electrode is varied from -5000 volt to +5000 volt. In the most of the concave and convex plasma shapes ion beam emittance can be calculated by using separate standard deviations of positions and elevations angles. Ion beam emittance as a function of the curvature of the plasma meniscus for different plasma shapes ( flat concave and convex ) without space change at acceleration voltage varied from -5000 volt to +5000 volt applied to the acceleration electrode of the triode extraction system has been investigated. Tbe influence of the extraction gap on ion beam emittance for a plasma concave shape of 3.75 mm without space charge at acceleration voltage, V a cc = -2000 volt applied to the acceleration electrode of the triode extraction system has been determined. Also the influence of space charge on ion beam emittance for variable plasma meniscus at acceleration voltage, V a cc = - 2000 volt applied to the acceleration electrode of. the triode extraction system has been studied

  17. Simulation of the plasma meniscus with and without space charge using triode extraction system

    International Nuclear Information System (INIS)

    Rahman, M.M.Abdel; El-Khabeary, H.

    2009-01-01

    In this work, simulation of the singly charged argon ion trajectories for a variable plasma meniscus is studied with and without space charge for the triode extraction system by using SIMION 3D (Simulation of Ion Optics in Three Dimensions) version 7 personal computer program. The influence of acceleration voltage applied to the acceleration electrode of the triode extraction system on the shape of the plasma meniscus has been determined. The plasma electrode is set at +5000 volt and the acceleration voltage applied to the acceleration electrode is varied from -5000 volt to +5000 volt. In the most of the concave and convex plasma shapes, ion beam emittance can be calculated by using separate standard deviations of positions and elevations angles. Ion beam emittance as a function of the curvature of the plasma meniscus for different plasma shapes ( flat, concave and convex ) without space charge at acceleration voltage varied from -5000 volt to +5000 volt applied to the acceleration electrode of the triode extraction system has been investigated. The influence of the extraction gap on ion beam emittance for a plasma concave shape of 3.75 mm without space charge at acceleration voltage, V acc = -2000 volt applied to the acceleration electrode of the triode extraction system has been determined. Also the influence of space charge on ion beam emittance for variable plasma meniscus at acceleration voltage, V acc = -2000 volt applied to the acceleration electrode of the triode extraction system has been studied. (author)

  18. DEMONSTRATION BULLETIN: IN SITU ELECTROKINETIC EXTRACTION SYSTEM - SANDIA NATIONAL LABORATORIES

    Science.gov (United States)

    Sandia National Laboratories (SNL) has developed an in situ soil remediation system that uses electrokinetic principles to remediate hexavalent chromium-contaminated unsaturated or partially saturated soils. The technology involves the in situ application of direct current to the...

  19. Towards a Technique for Extracting Microservices from Monolithic Enterprise Systems

    OpenAIRE

    Levcovitz, Alessandra; Terra, Ricardo; Valente, Marco Tulio

    2016-01-01

    The idea behind microservices architecture is to develop a single large, complex application as a suite of small, cohesive, independent services. On the other way, monolithic systems get larger over the time, deviating from the intended architecture, and becoming risky and expensive to evolve. This paper describes a technique to identify and define microservices on monolithic enterprise systems. As the major contribution, our evaluation shows that our approach was able to identify relevant ca...

  20. A System for Extracting Study Design Parameters from Nutritional Genomics Abstracts

    Directory of Open Access Journals (Sweden)

    Kelly Cassidy

    2013-06-01

    Full Text Available The extraction of study design parameters from biomedical journal articles is an important problem in natural language processing (NLP. Such parameters define the characteristics of a study, such as the duration, the number of subjects, and their profile. Here we present a system for extracting study design parameters from sentences in article abstracts. This system will be used as a component of a larger system for creating nutrigenomics networks from articles in the nutritional genomics domain. The algorithms presented consist of manually designed rules expressed either as regular expressions or in terms of sentence parse structure. A number of filters and NLP tools are also utilized within a pipelined algorithmic framework. Using this novel approach, our system performs extraction at a finer level of granularity than comparable systems, while generating results that surpass the current state of the art.

  1. A System for Extracting Study Design Parameters from Nutritional Genomics Abstracts.

    Science.gov (United States)

    Kelly, Cassidy; Yang, Hui

    2013-06-01

    The extraction of study design parameters from biomedical journal articles is an important problem in natural language processing (NLP). Such parameters define the characteristics of a study, such as the duration, the number of subjects, and their profile. Here we present a system for extracting study design parameters from sentences in article abstracts. This system will be used as a component of a larger system for creating nutrigenomics networks from articles in the nutritional genomics domain. The algorithms presented consist of manually designed rules expressed either as regular expressions or in terms of sentence parse structure. A number of filters and NLP tools are also utilized within a pipelined algorithmic framework. Using this novel approach, our system performs extraction at a finer level of granularity than comparable systems, while generating results that surpass the current state of the art.

  2. NuMI proton kicker extraction magnet termination resistor system

    Energy Technology Data Exchange (ETDEWEB)

    Reeves, S.R.; Jensen, C.C.; /Fermilab

    2005-05-01

    The temperature stability of the kicker magnet termination resistor assembly directly affects the field flatness and amplitude stability. Comprehensive thermal enhancements were made to the existing Main Injector resistor assembly design to satisfy NuMI performance specifications. Additionally, a fluid-processing system utilizing Fluorinert{reg_sign} FC-77 high-voltage dielectric was built to precisely control the setpoint temperature of the resistor assembly from 70 to 120F, required to maintain constant resistance during changing operational modes. The Fluorinert{reg_sign} must be continually processed to remove hazardous breakdown products caused by radiation exposure to prevent chemical attack of system components. Design details of the termination resistor assembly and Fluorinert{reg_sign} processing system are described. Early performance results will be presented.

  3. NuMI Proton Kicker Extraction Magnet Termination Resistor System

    CERN Document Server

    Reeves, Scott

    2005-01-01

    The temperature stability of the kicker magnet termination resistor assembly directly affects the field flatness and amplitude stability of the kick. Comprehensive thermal enhancements were made to the existing Main Injector resistor assembly design to satisfy NuMI performance specifications. Additionally, a fluid-processing system utilizing Fluorinert® FC-77 high-voltage dielectric was built to precisely control the setpoint temperature of the resistor assembly from 70 to 120F, required to maintain constant resistance during changing operational modes. The Fluorinert® must be continually processed to remove hazardous breakdown products caused by radiation exposure to prevent chemical attack of system components. Design details of the termination resistor assembly and Fluorinert® processing system are described. Early performance results will be presented.

  4. Third phase formation in the extraction of Th(NO{sub 3}){sub 4} by Tri-sec-butyl phosphate. A comparison with Tri-n-butyl phosphate

    Energy Technology Data Exchange (ETDEWEB)

    Chandrasekar, Aditi; Suresh, A.; Sivaraman, N. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Chemistry Group

    2017-06-01

    Earlier studies carried out in our laboratory indicated that Tri-sec-butyl phosphate (TsBP) is a potential extractant for U/Th separation. Also, the third phase formation tendency of TsBP is lower compared to its isomers, Tri-n-butyl-phosphate (TBP) and Tri-iso-butyl phosphate (TiBP). In this context, the extraction and third phase formation behaviour of 1.1 M solutions of TiBP and TsBP in n-dodecane in the extraction of Th(IV) from 1 M HNO{sub 3} at 303 K over a wide range of Th concentrations were investigated in the present study and the results are compared with the literature data on TBP system. Concentrations of Th(IV) and HNO{sub 3} loaded in the organic phase before third phase formation (biphasic region) as well as in third phase and diluent-rich phase after third phase formation (triphasic region) were measured as a function of equilibrium aqueous phase Th(IV) concentration. The density of loaded organic phase was also measured at various Th(IV) concentrations. The extraction profiles in the biphasic region indicated that extraction of Th(IV) by TBP is higher than that of TiBP which in turn is higher than that of TsBP. Extractant concentration in the diluent-rich phase and third phase was measured for the triphasic region.

  5. Upgrade and Tests of the SPS Fast Extraction Kicker System for LHC and CNGS

    CERN Document Server

    Gaxiola, E; Burkel, P; Carlier, E; Castronuovo, F; Ducimetière, L; Sillanoli, Y; Timmins, M; Uythoven, J

    2004-01-01

    A fast extraction kicker system has been installed in the SPS and successfully used in extraction tests in 2003. It will serve to send beam to the anticlockwise LHC ring and the CNGS neutrino facility. The magnets and pulse generators have been recuperated from an earlier installation and upgraded to fit the present application. Hardware improvements include diode stacks as replacement of the previous dump thyratron switches, a cooling system of the magnets, sensors for its ferrite temperatures and magnetic field quality assessment. In preparation of the future use for 450 GeV/c transfer to LHC and double batch extraction at 400 GeV/c for CNGS the tests comprised extractions of single bunches, twelve bunches in a single extraction and single bunches in a double extraction. The measured kick characteristics of the upgraded system are presented, along with a discussion of Pspice simulation results. Further improvements will be discussed which are intended to make the system comply with the specifications for CN...

  6. Enhanced refrigerant capacity in Gd-Al-Co microwires with a biphase nanocrystalline/amorphous structure

    International Nuclear Information System (INIS)

    Shen, H. X.; Xing, D. W.; Liu, Y. F.; Sun, J. F.; Sánchez Llamazares, J. L.; Sánchez-Valdés, C. F.; Belliveau, H.; Srikanth, H.; Phan, M. H.; Wang, H.; Qin, F. X.

    2016-01-01

    A class of biphase nanocrystalline/amorphous Gd (50+5x) Al (30−5x) Co 20 (x = 0, 1, 2) microwires fabricated directly by melt-extraction is reported. High resolution transmission electron microscopy and Fourier function transform based analysis indicate the presence of a volume fraction (∼20%) of ∼10 nm sized nanocrystallities uniformly embedded in an amorphous matrix. The microwires possess excellent magnetocaloric properties, with large values of the isothermal entropy change (−ΔS M  ∼ 9.7 J kg −1 K −1 ), the adiabatic temperature change (ΔT ad  ∼ 5.2 K), and the refrigerant capacity (RC ∼ 654 J kg −1 ) for a field change of 5 T. The addition of Gd significantly alters T C while preserving large values of the ΔS M and RC. The nanocrystallites allow for enhanced RC as well as a broader operating temperature span of a magnetic bed for energy-efficient magnetic refrigeration.

  7. Enhanced refrigerant capacity in Gd-Al-Co microwires with a biphase nanocrystalline/amorphous structure

    Energy Technology Data Exchange (ETDEWEB)

    Shen, H. X. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Department of Physics, University of South Florida, Tampa, Florida 33620 (United States); Xing, D. W.; Liu, Y. F.; Sun, J. F. [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Sánchez Llamazares, J. L. [Instituto Potosino de Investigación Científica y Tecnológica A.C., Camino a la Presa San José 2055 Col. Lomas 4a, San Luis Potosí, S.L.P. 78216 (Mexico); Sánchez-Valdés, C. F. [Centro de Nanociencias y Nanotecnología, Universidad Nacional Autónoma de México, AP 14, Ensenada 22860, Baja California (Mexico); Belliveau, H.; Srikanth, H.; Phan, M. H., E-mail: phanm@usf.edu [Department of Physics, University of South Florida, Tampa, Florida 33620 (United States); Wang, H.; Qin, F. X. [Institute for Composites Science and Innovation (InCSI), College of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China)

    2016-02-29

    A class of biphase nanocrystalline/amorphous Gd{sub (50+5x)}Al{sub (30−5x)}Co{sub 20} (x = 0, 1, 2) microwires fabricated directly by melt-extraction is reported. High resolution transmission electron microscopy and Fourier function transform based analysis indicate the presence of a volume fraction (∼20%) of ∼10 nm sized nanocrystallities uniformly embedded in an amorphous matrix. The microwires possess excellent magnetocaloric properties, with large values of the isothermal entropy change (−ΔS{sub M} ∼ 9.7 J kg{sup −1} K{sup −1}), the adiabatic temperature change (ΔT{sub ad} ∼ 5.2 K), and the refrigerant capacity (RC ∼ 654 J kg{sup −1}) for a field change of 5 T. The addition of Gd significantly alters T{sub C} while preserving large values of the ΔS{sub M} and RC. The nanocrystallites allow for enhanced RC as well as a broader operating temperature span of a magnetic bed for energy-efficient magnetic refrigeration.

  8. You’ve Got Email: a Workflow Management Extraction System

    NARCIS (Netherlands)

    P. Chaipornkaew (Piyanuch); T. Prexawanprasut (Takorn); M.J. McAleer (Michael)

    2017-01-01

    textabstractEmail is one of the most powerful tools for communication. Many businesses use email as the main channel for communication, so it is possible that substantial data are included in email content. In order to help businesses grow faster, a workflow management system may be required. The

  9. Crown ethers as size-selective synergists in solvent extraction systems: a new selectivity parameter

    International Nuclear Information System (INIS)

    Kinard, W.F.; McDowell, W.J.

    1981-01-01

    Mixtures of macrocyclic polyethers (crown ethers) and organic-phase-soluble liquid cation exchangers have been found to produce a synergistic effect in the extraction of metal ions. The synergistic effect is size selective; that is, it tends to be greatest for those ions that best fit the crown ether cavity. The mixtures of a liquid cation exchanger and a crown ether also allow metal ion extraction from common mineral-acid anion systems (NO 3 - , Cl - , SO 4 2- ) that would be impossible with the crown ether alone, because of the difficulty of solubilizing those anions in nonpolar solvents. This cooperation makes the use of crown ethers as size-selective coordinators available for process applications. Size selectivity of compounds such as crown ethers may thus become a useful new parameter in designing selective solvent extraction systems. Results are reported for alkali (including Cs) and alkaline earth (including Sr) extraction by HDEHP mixed with various crown ethers. (author)

  10. Antiepileptic and central nervous system depressant activity of Sechium edule fruit extract

    Directory of Open Access Journals (Sweden)

    Sayeed Mohammed Firdous Mumtaz

    2012-08-01

    Full Text Available The effect of ethanol extract of fruits of Sechium edule on antiepileptic and central nervous system (CNS depressant model was studied in rats. The extract (200 mg/kg body weight, orally significantly reduced the duration of various phases of convulsions in both MES-induce seizures and in PTZ-induced convulsion. In CNS depressant model, the locomotor activity was also decreased in a dose dependent manner as compared to control group the extract and the rota rod test revealed a significant loss of muscular coordination.

  11. Design of the CERN MEDICIS Collection and Sample Extraction System

    CERN Document Server

    Brown, Alexander

    MEDICIS is a new facility at CERN ISOLDE that aims to produce radio-isotopes for medical research. Possible designs for the collection and transport system for the collection of radio-isotopes was investigated. A system using readily available equipment was devised with the the aim of keeping costs to a minimum whilst maintaining the highest safety standards. FLUKA, a Monte Carlo radiation transport code, was used to simulate the radiation from the isotopes to be collected. Of the isotopes to be collected 44Sc was found to give the largest dose by simulating the collection of all isotopes of interest to CERN’s MEDICIS facility, for medical research. The simulations helped guide the amount of shielding used in the final design. Swiss Regulations stipulating allowed activity level of individual isotopes was also considered within the body of the work.

  12. Multiple-Feature Extracting Modules Based Leak Mining System Design

    Directory of Open Access Journals (Sweden)

    Ying-Chiang Cho

    2013-01-01

    mining system that is equipped with SQL injection vulnerability detection, by means of an algorithm developed for the web crawler. In addition, we analyze portal sites of the governments of various countries or regions in order to investigate the information leaking status of each site. Subsequently, we analyze the database structure and content of each site, using the data collected. Thus, we make use of practical verification in order to focus on information security and privacy through black-box testing.

  13. The visual system discounts emotional deviants when extracting average expression.

    Science.gov (United States)

    Haberman, Jason; Whitney, David

    2010-10-01

    There has been a recent surge in the study of ensemble coding, the idea that the visual system represents a set of similar items using summary statistics (Alvarez & Oliva, 2008; Ariely, 2001; Chong & Treisman, 2003; Parkes, Lund, Angelucci, Solomon, & Morgan, 2001). We previously demonstrated that this ability extends to faces and thus requires a high level of object processing (Haberman & Whitney, 2007, 2009). Recent debate has centered on the nature of the summary representation of size (e.g., Myczek & Simons, 2008) and whether the perceived average simply reflects the sampling of a very small subset of the items in a set. In the present study, we explored this further in the context of faces, asking observers to judge the average expressions of sets of faces containing emotional outliers. Our results suggest that the visual system implicitly and unintentionally discounts the emotional outliers, thereby computing a summary representation that encompasses the vast majority of the information present. Additional computational modeling and behavioral results reveal that an intentional cognitive sampling strategy does not accurately capture observer performance. Observers derive precise ensemble information given a 250-msec exposure, suggesting a rapid and flexible system not bound by the limits of serial attention.

  14. Optical Matching of Slowly Extracted Beam with Transport System at HIMAC

    CERN Document Server

    Furukawa, Takuji; Katsumata, Masashi; Noda, Koji; Shibuya, Shinji; Shiraishi, Tadahiro; Takada, Eiichi; Torikoshi, Masami; Uesugi, Takehiro; Yamada, Satoru

    2005-01-01

    The optical matching between the ring and the transport line plays important role in order to control the beam size and profile after the transport. At HIMAC, thus, we have studied the optical matching of the slowly extracted beam. As a result, it was verified that the beam size of the slowly extracted beam were controlled owing to the optical matching. It was also found that small deviation of quadrupole strength in the ring brings orbit distortion at the transport system.

  15. Membrane contactor assisted water extraction system for separating hydrogen peroxide from a working solution, and method thereof

    Science.gov (United States)

    Snyder, Seth W [Lincolnwood, IL; Lin, Yupo J [Naperville, IL; Hestekin', Jamie A [Fayetteville, AR; Henry, Michael P [Batavia, IL; Pujado, Peter [Kildeer, IL; Oroskar, Anil [Oak Brook, IL; Kulprathipanja, Santi [Inverness, IL; Randhava, Sarabjit [Evanston, IL

    2010-09-21

    The present invention relates to a membrane contactor assisted extraction system and method for extracting a single phase species from multi-phase working solutions. More specifically one preferred embodiment of the invention relates to a method and system for membrane contactor assisted water (MCAWE) extraction of hydrogen peroxide (H.sub.2O.sub.2) from a working solution.

  16. Electronic simulation of the supported liquid membrane in electromembrane extraction systems: Improvement of the extraction by precise periodical reversing of the field polarity

    International Nuclear Information System (INIS)

    Moazami, Hamid Reza; Nojavan, Saeed; Zahedi, Pegah; Davarani, Saied Saeed Hosseiny

    2014-01-01

    Highlights: • A simple equivalent circuit has been proposed for a supported liquid membrane. • A dual charge transfer mechanism was proposed for electromembrane extraction. • An improvement was observed by precise periodical reversing of the field polarity. - Abstract: In order to understand the limitations of electromebrane extraction procedure better, a simple equivalent circuit has been proposed for a supported liquid membrane consisting of a resistor and a low leakage capacitor in series. To verify the equivalent circuit, it was subjected to a simulated periodical polarity changing potential and the resulting time variation of the current was compared with that of a real electromembrane extraction system. The results showed a good agreement between the simulated current patterns and those of the real ones. In order to investigate the impact of various limiting factors, the corresponding values of the equivalent circuit were estimated for a real electromembrane extraction system and were attributed to the physical parameters of the extraction system. A dual charge transfer mechanism was proposed for electromembrane extraction by combining general migration equation and fundamental aspects derived from the simulation. Dual mechanism comprises a current dependent contribution of analyte in total current and could support the possibility of an improvement in performance of an electromembrane extraction by application of an asymmetric polarity changing potential. The optimization of frequency and duty cycle of the asymmetric polarity exchanging potential resulted in a higher recovery (2.17 times greater) in comparison with the conventional electromebrane extraction. The simulation also provided more quantitative approaches toward the investigation of the mechanism of extraction and contribution of different limiting factors in electromembrane extraction. Results showed that the buildup of the double layer is the main limiting factor and the Joule heating has

  17. Systems studies on the extraction of uranium from seawater

    International Nuclear Information System (INIS)

    Driscoll, M.J.; Best, F.R.

    1981-11-01

    This report summarizes the work done at MIT during FY 1981 on the overall system design of a uranium-from-seawater facility. It consists of a sequence of seven major chapters, each of which was originally prepared as a stand-alone internal progress report. These chapters trace the historical progression of the MIT effort, from an early concern with scoping calculations to define the practical boundaries of a design envelope, as constrained by elementary economic and energy balance considerations, through a parallel evaluation of actively-pumped and passive current-driven concepts, and thence to quantification of the features of a second generation system based on a shipboard-mounted, actively-pumped concept designed around the use of thin beds of powdered ion exchange resin supported by cloth fiber cylinders (similar to the baghouse flyash filters used on power station offgas). An assessment of the apparently inherent limitations of even thin settled-bed sorber media then led to selection of an expanded bed (in the form of an ion exchange wool), which would permit an order of magnitude increase in flow loading, as a desirable advance. Thus the final two chapters evaluate ways in which this approach could be implemented, and the resulting performance levels which could be attained. Overall, U 3 O 8 production costs under 200 $/lb appear to be within reach if a high capacity (several thousand ppM U) ion exchange wool can be developed

  18. Portable test bench for the studies concerning ion sources and ion beam extraction and focusing systems

    International Nuclear Information System (INIS)

    Cordero Lopez, F.

    1961-01-01

    A portable test bench is described, which was designed to check ion sources, ion beam extraction and focusing systems before its use in a 600 KeV Cockcroft-Walton accelerator. The vacuum possibilities of the system are specially analyzed in connection with its particular use. The whole can be considered as a portable accelerator of low energy (50 keV). (Author)

  19. Long-Term Survival of Leptospira in a Biphasic Culture Medium Containing Charcoal

    Science.gov (United States)

    Myers, Donald M.; Varela-Díaz, Victor M.; Siniuk, Alicia A.

    1973-01-01

    A comparison was made of the survival of 28 leptospiral serotypes in Fletcher semisolid medium and in the same medium containing a basal layer of Fletcher medium plus 0.7% of agar and 0.5% of activated animal charcoal. A year after culture, more motile leptospires were observed by microscope examination in the biphasic medium. Two years after culture, 4 serotypes grown in the biphasic medium and 11 in Fletcher medium did not show motile cells. Nineteen of the serotypes maintained in Fletcher medium and 25 in the biphasic medium for 2 years grew on subculture into Fletcher medium. Subcultures from the biphasic medium showed the characteristic leptospiral ring growth earlier during the incubation period. PMID:4735486

  20. Biphasic cuirass ventilation is better than bag-valve mask ventilation for resuscitation following organophosphate poisoning

    Directory of Open Access Journals (Sweden)

    Ilan Gur

    2015-01-01

    Conclusions: The noninvasive, easy-to-operate Biphasic Cuirass Ventilation device was effective in reducing OP-induced mortality and might be advantageous in an organophosphate mass casualty event. This finding should be validated in further investigations.

  1. Development of a biphasic dissolution test for Deferasirox dispersible tablets and its application in establishing an in vitro-in vivo correlation.

    Science.gov (United States)

    Al Durdunji, Amal; AlKhatib, Hatim S; Al-Ghazawi, Mutasim

    2016-05-01

    In a biphasic dissolution medium, the integration of the in vitro dissolution of a drug in an aqueous phase and its subsequent partitioning into an organic phase is hypothesized to simulate the in vivo drug absorption. Such a methodology is expected to improve the probability of achieving a successful in vitro-in vivo correlation. Dissolution of Dispersible tablets of Deferasirox, a biopharmaceutics classification system type II compound, was studied in a biphasic dissolution medium using a flow-through dissolution apparatus coupled to a paddle apparatus. The experimental parameters associated with dissolution were optimized to discriminate between Deferasirox dispersible tablets of different formulations. The dissolution profiles obtained from this system were subsequently used to construct a level A in vitro-in vivo correlation. Copyright © 2016 Elsevier B.V. All rights reserved.

  2. Biphasic influence of dexamethasone exposure on embryonic vertebrate skeleton development

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Xin; Chen, Jian-long; Ma, Zheng-lai; Zhang, Zhao-long; Lv, Shun; Mai, Dong-mei; Liu, Jia-jia [Department of Histology and Embryology, Key Laboratory for Regenerative Medicine of the Ministry of Education, School of Medicine, Jinan University, Guangzhou 510632 (China); Chuai, Manli [Division of Cell and Developmental Biology, University of Dundee, Dundee DD1 5EH (United Kingdom); Lee, Kenneth Ka Ho; Wan, Chao [Stem Cell and Regeneration Thematic Research Programme, School of Biomedical Sciences, Chinese University of Hong Kong, Shatin (Hong Kong); Yang, Xuesong, E-mail: yang_xuesong@126.com [Department of Histology and Embryology, Key Laboratory for Regenerative Medicine of the Ministry of Education, School of Medicine, Jinan University, Guangzhou 510632 (China); Institute of Fetal-Preterm Labor Medicine, Jinan University, Guangzhou 510632 (China)

    2014-11-15

    increased in mesenchymal cell mass treated by low concentration of Dex. Mmp-13 expression was obviously up-regulated by Dex in both mesenchymal cells and primary chondrocyte cultures. And Col10a1 expression was also increased by Dex exposure in chondrocyte. In summary, we have revealed that different concentrations of Dex exposure during early gestation could exert a biphasic effect on vertebrate skeletal development. - Highlights: • Chick embryos occurred shortening of the long bone following Dex exposure. • Dex suppressed chondrocytes proliferation and promoted apoptosis. • Dex exposure decreased ALP production and up-regulated Runx-2 and Mmp-13. • Dex exhibited biphasic effects on chondrogenic proliferation and nodule formation. • The hypertrophy and ossification were accelerated by Dex both in vivo and in vitro.

  3. Biphasic influence of dexamethasone exposure on embryonic vertebrate skeleton development

    International Nuclear Information System (INIS)

    Cheng, Xin; Chen, Jian-long; Ma, Zheng-lai; Zhang, Zhao-long; Lv, Shun; Mai, Dong-mei; Liu, Jia-jia; Chuai, Manli; Lee, Kenneth Ka Ho; Wan, Chao; Yang, Xuesong

    2014-01-01

    in mesenchymal cell mass treated by low concentration of Dex. Mmp-13 expression was obviously up-regulated by Dex in both mesenchymal cells and primary chondrocyte cultures. And Col10a1 expression was also increased by Dex exposure in chondrocyte. In summary, we have revealed that different concentrations of Dex exposure during early gestation could exert a biphasic effect on vertebrate skeletal development. - Highlights: • Chick embryos occurred shortening of the long bone following Dex exposure. • Dex suppressed chondrocytes proliferation and promoted apoptosis. • Dex exposure decreased ALP production and up-regulated Runx-2 and Mmp-13. • Dex exhibited biphasic effects on chondrogenic proliferation and nodule formation. • The hypertrophy and ossification were accelerated by Dex both in vivo and in vitro

  4. Improvement of extraction system geometry with suppression of possible Penning discharge ignition

    Science.gov (United States)

    Delferrière, O.; Gobin, R.; Harrault, F.; Nyckees, S.; Tuske, O.

    2014-02-01

    During the past two years, a new ECR 2.45 GHz type ion source has been developed especially dedicated to intense light ion injector project like IPHI (Injecteur Proton Haute Intensité), IFMIF (International Fusion Materials Irradiation Facility), to reduce beam emittance at RFQ entrance by shortening the length of the LEBT. This new ALISES concept (Advanced Light Ion Source Extraction System) is based on the use of an additional LEBT short length solenoid very close to the extraction aperture. The fringe field of this new solenoid produces the needed magnetic field to create the ECR resonance in the plasma chamber. Such geometry allows first putting the solenoid at ground potential, while saving space in front of the extraction to move the first LEBT solenoid closer and focus earlier the intense extracted beam. During the commissioning of the source in 2011-2012, ALISES has produced about 20 mA extracted from a 6 mm diameter plasma extraction hole at 23 kV. But the magnetic configuration combined to the new extraction system geometry led to important Penning discharge conditions in the accelerator column. Lots of them have been eliminated by inserting glass pieces between electrodes to modify equipotential lines with unfavorable ExB vacuum zones where particles were produced and trapped. To study Penning discharge location, several 3D calculations have been performed with OPERA-3D/TOSCA code to simulate the possible production and trapping of electrons in the extraction system. The results obtained on different sources already built have shown very good agreement with sparks location observed experimentally on electrodes. The simulations results as well as experimental measurements are presented and solutions to prevent possible Penning discharge in future source geometries are established.

  5. Aqueous Two-Phase Extraction of Polyphenols Using a Microchannel System – Process Optimization and Intensification

    Directory of Open Access Journals (Sweden)

    Ivana Rukavina

    2011-01-01

    Full Text Available Polyphenols are one of the most numerous and widespread groups of compounds in the plant world. Nowadays, organic solvents such as methanol, ethanol, acetone, dimethylformamide, ethyl acetate and diethylether are mainly used for the extraction of polyphenols. These solvents require special process conditions and special care in the disposal of the used solvents. In this paper, the extraction of polyphenols from the model solution was performed using the aqueous two-phase system which contains 80.90 % water and represents low burden on the environment. The aqueous solution of gallic acid (GA was used as a model solution of polyphenols. The extraction was performed in the aqueous two-phase system containing PEG6000/H2O/(NH42SO4 in a macroextractor (V=10 mL and microextractor (V=14 ƒμL. The influence of the process parameters, the concentration of gallic acid, pH and composition of the aqueous two-phase system was investigated in order to maximize the partition coefficient. The method of multifactor experimental planning was used to optimize the extraction process and the results were statistically analysed using the evolutionary operation method (EVOP. Optimal operating conditions of the extraction process were pH=6.50, γGA=4.50 g/L, the mass fraction of polyethylene glycol (PEG wPEG=0.1037 g/g and the mass fraction of ammonium sulphate (AMS wAMS=0.0925 g/g. Under these conditions the maximal partition coefficient of K=5.54 and the extraction efficiency of E=89.11 % were achieved and successfully applied for total phenol extraction from white wine in the macro- and microextractor. Approximately the same partition coefficients and extraction efficiency were achieved in the microextractor within a 60-fold shorter residence time.

  6. Use of ethyl lactate to extract bioactive compounds from Cytisus scoparius: Comparison of pressurized liquid extraction and medium scale ambient temperature systems.

    Science.gov (United States)

    Lores, Marta; Pájaro, Marta; Álvarez-Casas, Marta; Domínguez, Jorge; García-Jares, Carmen

    2015-08-01

    An important trend in the extraction of chemical compounds is the application of new environmentally friendly, food grade solvents. Ethyl lactate (ethyl 2-hydroxypropanoate), produced by fermentation of carbohydrates, is miscible with both hydrophilic and hydrophobic compounds being a potentially good solvent for bioactive compounds. Despite its relatively wide use as a general solvent, the utilization of ethyl lactate as an extraction solvent has only recently been considered. Here, we evaluate the possible use of ethyl lactate to extract phenolic compounds from wild plants belonging to Cytisus scoparius, and we compare the characteristics of the extracts obtained by Pressurized Solvent Extraction (the total phenolics content, the antioxidant activity and the concentration of the major polyphenols) with those of other extracts obtained with methanol. In order to explore the industrial production of the ethyl lactate Cytisus extract, we also evaluate medium scale ambient temperature setups. The whole plant and the different parts (flowers, branches, and seed pods) were evaluated separately as potential sources of polyphenols. All extracts were analyzed by LC-MS/MS for accurate identification of the major polyphenols. Similar phenolic profiles were obtained when using ethyl lactate or methanol. The main bioactives found in the Cytisus extract were the non-flavonoid phenolic compounds caffeic and protocatechuic acids and 3,4-dihydroxybenzaldehyde; the flavonoids rutin, kaempferol and quercetin; the flavones chrysin, orientin and apigenin; and the alkaloid lupanine. Regarding the comparison of the extraction systems, although the performance of the PLE was much better than that of the ambient-temperature columns, the energy consumption was also much higher. Ethyl lactate has resulted an efficient extraction solvent for polyphenols from C. scoparius, yielding extracts with high levels of plant phenolics and antioxidant activity. The antimicrobial activity of these

  7. An Effective Fault Feature Extraction Method for Gas Turbine Generator System Diagnosis

    Directory of Open Access Journals (Sweden)

    Jian-Hua Zhong

    2016-01-01

    Full Text Available Fault diagnosis is very important to maintain the operation of a gas turbine generator system (GTGS in power plants, where any abnormal situations will interrupt the electricity supply. The fault diagnosis of the GTGS faces the main challenge that the acquired data, vibration or sound signals, contain a great deal of redundant information which extends the fault identification time and degrades the diagnostic accuracy. To improve the diagnostic performance in the GTGS, an effective fault feature extraction framework is proposed to solve the problem of the signal disorder and redundant information in the acquired signal. The proposed framework combines feature extraction with a general machine learning method, support vector machine (SVM, to implement an intelligent fault diagnosis. The feature extraction method adopts wavelet packet transform and time-domain statistical features to extract the features of faults from the vibration signal. To further reduce the redundant information in extracted features, kernel principal component analysis is applied in this study. Experimental results indicate that the proposed feature extracted technique is an effective method to extract the useful features of faults, resulting in improvement of the performance of fault diagnosis for the GTGS.

  8. Application of raisin extracts as preservatives in liquid bread and bread systems.

    Science.gov (United States)

    Wei, Q; Wolf-Hall, C; Hall, C A

    2009-01-01

    Interest in natural ingredients with multifunctions in food has led to the investigation of the antimicrobial activity of raisins, a traditional baking ingredient. Water and 60% ethanol extracts, and raisin juice concentrate (RJC, a commercial food ingredient) were assessed for their ability to inhibit the growth of ropy-bread-causing Bacillus species. The ability of these additives and raisin paste were tested for antifungal activity in liquid bread model system and bread. In the liquid bread model, concentrations as low as 20 and 36 mg crude extract or RJC per gram media significantly (P RJC (70 mg/g dough) produced bread that had equivalent mold-free shelf life. The mean mold-free shelf life of the bread containing 7.5% water extract was 18.1 +/- 3.3 d at room temperature while the negative control was mold free for 9.4 +/- 2.4 d. The antifungal efficacy of the extracts in bread was equivalent to 0.24% calcium propionate in 21 d of storage. Doubling the concentration of the extract did not improve the mold-retarding property in bread. The bread containing raisin paste, the percentage of which in dough was equivalent to 15% raisin extract, exhibited a stronger antifungal activity than did the extracts in bread.

  9. A generalizable NLP framework for fast development of pattern-based biomedical relation extraction systems.

    Science.gov (United States)

    Peng, Yifan; Torii, Manabu; Wu, Cathy H; Vijay-Shanker, K

    2014-08-23

    Text mining is increasingly used in the biomedical domain because of its ability to automatically gather information from large amount of scientific articles. One important task in biomedical text mining is relation extraction, which aims to identify designated relations among biological entities reported in literature. A relation extraction system achieving high performance is expensive to develop because of the substantial time and effort required for its design and implementation. Here, we report a novel framework to facilitate the development of a pattern-based biomedical relation extraction system. It has several unique design features: (1) leveraging syntactic variations possible in a language and automatically generating extraction patterns in a systematic manner, (2) applying sentence simplification to improve the coverage of extraction patterns, and (3) identifying referential relations between a syntactic argument of a predicate and the actual target expected in the relation extraction task. A relation extraction system derived using the proposed framework achieved overall F-scores of 72.66% for the Simple events and 55.57% for the Binding events on the BioNLP-ST 2011 GE test set, comparing favorably with the top performing systems that participated in the BioNLP-ST 2011 GE task. We obtained similar results on the BioNLP-ST 2013 GE test set (80.07% and 60.58%, respectively). We conducted additional experiments on the training and development sets to provide a more detailed analysis of the system and its individual modules. This analysis indicates that without increasing the number of patterns, simplification and referential relation linking play a key role in the effective extraction of biomedical relations. In this paper, we present a novel framework for fast development of relation extraction systems. The framework requires only a list of triggers as input, and does not need information from an annotated corpus. Thus, we reduce the involvement of domain

  10. Energy Extracting and Quench Protection System in the LHC

    CERN Document Server

    Abu Siam, Mansour

    2016-01-01

    quadrupole magnets. The electromagnets are built of special cables that operate in superconducting state by cooling them to 1.9K (-271.3℃); the superconducting magnets of the LHC are powered in about 1700 electrical circuits. A phenomenon called quench can spontaneously occur in superconducting magnets, which means that the superconductivity is lost in part of their windings. The energy stored within the magnet, up to 1.3 GJ, can cause severe damage. In order to protect the superconducting elements after a resistive transition, the energy is dissipated into a dump resistor installed in series with the magnet chain that is switched into the circuit by opening circuit breakers. The system described above is utilized for magnets installed in the LHC that operate under currents ranging from 600A up to 13kA. For the next LHC upgrade (High Luminosity) there is a need for circuit breakers capable of interrupting high DC currents in a solely inductive circuit within one millisecond and under development of very hig...

  11. Multiple-feature extracting modules based leak mining system design.

    Science.gov (United States)

    Cho, Ying-Chiang; Pan, Jen-Yi

    2013-01-01

    Over the years, human dependence on the Internet has increased dramatically. A large amount of information is placed on the Internet and retrieved from it daily, which makes web security in terms of online information a major concern. In recent years, the most problematic issues in web security have been e-mail address leakage and SQL injection attacks. There are many possible causes of information leakage, such as inadequate precautions during the programming process, which lead to the leakage of e-mail addresses entered online or insufficient protection of database information, a loophole that enables malicious users to steal online content. In this paper, we implement a crawler mining system that is equipped with SQL injection vulnerability detection, by means of an algorithm developed for the web crawler. In addition, we analyze portal sites of the governments of various countries or regions in order to investigate the information leaking status of each site. Subsequently, we analyze the database structure and content of each site, using the data collected. Thus, we make use of practical verification in order to focus on information security and privacy through black-box testing.

  12. Overall requirements for an advanced underground coal extraction system

    Energy Technology Data Exchange (ETDEWEB)

    Goldsmith, M.; Lavin, M.L.

    1980-10-15

    This report presents overall requirements on underground mining systems suitable for coal seams exploitable in the year 2000, with particular relevance to the resources of Central Appalachia. These requirements may be summarized as follows: (1) Production Cost: demonstrate a return on incremental investment of 1.5 to 2.5 times the value required by a low-risk capital project. (2) Miner Safety: achieve at least a 50% reduction in deaths and disabling injuries per million man-hours. (3) Miner Health: meet the intent of all applicable regulations, with particular attention to coal dust, carcinogens, and mutagens; and with continued emphasis on acceptable levels of noise and vibration, lighting, humidity and temperature, and adequate work space. (4) Environmental Impact: maintain the value of mined and adjacent lands at the pre-mining value following reclamation; mitigation of off-site impacts should not cost more than the procedures used in contemporary mining. (5) Coal Conservation: the recovery of coal from the seam being mined should be at least as good as the best available contemporary technology operating in comparable conditions. No significant trade-offs between production cost and other performance indices were found.

  13. Design of the Injection and extraction system and related machine protection for the Clic Damping Rings

    CERN Document Server

    Apsimon, Robert; Barnes, Mike; Borburgh, Jan; Goddard, Brennan; Papaphilippou, Yannis; Uythoven, Jan

    2014-01-01

    Linear machines such as CLIC have relatively low rates of collision between bunches compared to their circular counterparts. In order to achieve the required luminosity, a very small spot size is envisaged at the interaction point, thus a low emittance beam is needed. Damping rings are essential for producing the low emittances needed for the CLIC main beam. It is crucial that the beams are injected and extracted from the damping rings in a stable and repeatable fashion to minimise emittance blow-up and beam jitter at the interaction point; both of these effects will deteriorate the luminosity at the interaction point. In this paper, the parameters and constraints of the injection and extraction systems are considered and the design of these systems is optimised within this parameter space. Related machine protection is considered in order to prevent damage from potential failure modes of the injection and extraction systems.

  14. [System evaluation on Ginkgo Biloba extract in the treatment of acute cerebral infarction].

    Science.gov (United States)

    Wang, Lin; Zhang, Tao; Bai, Kezhen

    2015-10-01

    To evaluate the effect and safety of Ginkgo Biloba extract on the treatment of acute cerebral infarction.
 The Database of Wanfang, China National Knowledge Infrastructure (CNKI) and VIPU were screened for literatures regarding Ginkgo Biloba extract in the treatment of acute cerebral infarction, including the clinical randomized controlled trials. Meta-analysis based on the Revman 4.2 system was performed.
 Compared with the control group, treatment with Ginkgo Biloba extract enhanced efficacy in the treatment of acute cerebral infarction (OR: 1.60-5.53), which displayed an improved neural function defect score [WMD -3.12 (95%CI: -3.96- -2.28)].
 Ginkgo Biloba extract is beneficial to the improvement of neurological function in patients with acute cerebral infarction and it is safe for patients.

  15. [Study on biopharmaceutics classification system for Chinese materia medica of extract of Huanglian].

    Science.gov (United States)

    Liu, Yang; Yin, Xiu-Wen; Wang, Zi-Yu; Li, Xue-Lian; Pan, Meng; Li, Yan-Ping; Dong, Ling

    2017-11-01

    One of the advantages of biopharmaceutics classification system of Chinese materia medica (CMMBCS) is expanding the classification research level from single ingredient to multi-components of Chinese herb, and from multi-components research to holistic research of the Chinese materia medica. In present paper, the alkaloids of extract of huanglian were chosen as the main research object to explore their change rules in solubility and intestinal permeability of single-component and multi-components, and to determine the biopharmaceutical classification of extract of Huanglian from holistic level. The typical shake-flask method and HPLC were used to detect the solubility of single ingredient of alkaloids from extract of huanglian. The quantitative research of alkaloids in intestinal absorption was measured in single-pass intestinal perfusion experiment while permeability coefficient of extract of huanglian was calculated by self-defined weight coefficient method. Copyright© by the Chinese Pharmaceutical Association.

  16. Biphasic oxidation of oxy-hemoglobin in bloodstains.

    Directory of Open Access Journals (Sweden)

    Rolf H Bremmer

    Full Text Available BACKGROUND: In forensic science, age determination of bloodstains can be crucial in reconstructing crimes. Upon exiting the body, bloodstains transit from bright red to dark brown, which is attributed to oxidation of oxy-hemoglobin (HbO(2 to met-hemoglobin (met-Hb and hemichrome (HC. The fractions of HbO(2, met-Hb and HC in a bloodstain can be used for age determination of bloodstains. In this study, we further analyze the conversion of HbO(2 to met-Hb and HC, and determine the effect of temperature and humidity on the conversion rates. METHODOLOGY: The fractions of HbO(2, met-Hb and HC in a bloodstain, as determined by quantitative analysis of optical reflectance spectra (450-800 nm, were measured as function of age, temperature and humidity. Additionally, Optical Coherence Tomography around 1300 nm was used to confirm quantitative spectral analysis approach. CONCLUSIONS: The oxidation rate of HbO(2 in bloodstains is biphasic. At first, the oxidation of HbO(2 is rapid, but slows down after a few hours. These oxidation rates are strongly temperature dependent. However, the oxidation of HbO(2 seems to be independent of humidity, whereas the transition of met-Hb into HC strongly depends on humidity. Knowledge of these decay rates is indispensable for translating laboratory results into forensic practice, and to enable bloodstain age determination on the crime scene.

  17. A biphasic model for bleeding in soft tissue

    Science.gov (United States)

    Chang, Yi-Jui; Chong, Kwitae; Eldredge, Jeff D.; Teran, Joseph; Benharash, Peyman; Dutson, Erik

    2017-11-01

    The modeling of blood passing through soft tissues in the body is important for medical applications. The current study aims to capture the effect of tissue swelling and the transport of blood under bleeding or hemorrhaging conditions. The soft tissue is considered as a non-static poro-hyperelastic material with liquid-filled voids. A biphasic formulation effectively, a generalization of Darcy's law-is utilized, treating the phases as occupying fractions of the same volume. The interaction between phases is captured through a Stokes-like friction force on their relative velocities and a pressure that penalizes deviations from volume fractions summing to unity. The soft tissue is modeled as a hyperelastic material with a typical J-shaped stress-strain curve, while blood is considered as a Newtonian fluid. The method of Smoothed Particle Hydrodynamics is used to discretize the conservation equations based on the ease of treating free surfaces in the liquid. Simulations of swelling under acute hemorrhage and of draining under gravity and compression will be demonstrated. Ongoing progress in modeling of organ tissues under injuries and surgical conditions will be discussed.

  18. Evolution of the optimum bidirectional (+/- biphasic) wave for defibrillation.

    Science.gov (United States)

    Geddes, L A; Havel, W

    2000-01-01

    Introduction of the asymmetric bidirectional (+/- biphasic) current waveform has made it possible to achieve ventricular defibrillation with less energy and current than are needed with a unidirectional (monophasic) waveform. The symmetrical bidirectional (sinusoidal) waveform was used for the first human-heart defibrillation. Subsequent studies employed the underdamped and overdamped sine waves, then the trapezoidal (monophasic) wave. Studies were then undertaken to investigate the benefit of adding a second identical and inverted wave; little success rewarded these efforts until it was discovered that the second inverted wave needed to be much less in amplitude to lower the threshold for defibrillation. However, there is no physiologic theory that explains the mechanism of action of the bidirectional wave, nor does any theory predict the optimum amplitude and time dimensions for the second inverted wave. The authors analyze the research that shows that the threshold defibrillation energy is lowest when the charge in the second, inverted phase is slightly more than a third of that in the first phase. An ion-flux, spatial-K+ summation hypothesis is presented that shows the effect on myocardial cells of adding the second inverted current pulse.

  19. Functional properties of the isomorphic biphasic algal life cycle.

    Science.gov (United States)

    Thornber, Carol S

    2006-10-01

    Many species of marine algae have life cycles that involve multiple separate, free-living phases that frequently differ in ploidy levels. These complex life cycles have received increasing scientific attention over the past few decades, due to their usefulness for both ecological and evolutionary studies. I present a synthesis of our current knowledge of the ecological functioning and evolutionary implications of the isomorphic, biphasic life cycles commonly found in many species of marine algae. There are both costs and benefits to life cycles with 2 morphologically similar but separate, free-living phases that differ in ploidy levels (haploids and diploids). Evolutionary theory predicts that the existence of subtle yet important differences between the phases may be what allows these life cycles to be maintained. Different phases of the same species can vary in abundance, in demographic parameters such as mortality and fecundity, in their physiology, and in their resistance to herbivory. Some taxonomic groups within the red algae have received significant attention toward these issues, while our knowledge of these properties for brown and green algae remains limited.

  20. Comparison between FEBio and Abaqus for biphasic contact problems.

    Science.gov (United States)

    Meng, Qingen; Jin, Zhongmin; Fisher, John; Wilcox, Ruth

    2013-09-01

    Articular cartilage plays an important role in the function of diarthrodial joints. Computational methods have been used to study the biphasic mechanics of cartilage, and Abaqus has been one of the most widely used commercial software packages for this purpose. A newly developed open-source finite element solver, FEBio, has been developed specifically for biomechanical applications. The aim of this study was to undertake a direct comparison between FEBio and Abaqus for some practical contact problems involving cartilage. Three model types, representing a porous flat-ended indentation test, a spherical-ended indentation test, and a conceptual natural joint contact model, were compared. In addition, a parameter sensitivity study was also performed for the spherical-ended indentation test to investigate the effects of changes in the input material properties on the model outputs, using both FEBio and Abaqus. Excellent agreement was found between FEBio and Abaqus for all of the model types and across the range of material properties that were investigated.

  1. The validation of forensic DNA extraction systems to utilize soil contaminated biological evidence.

    Science.gov (United States)

    Kasu, Mohaimin; Shires, Karen

    2015-07-01

    The production of full DNA profiles from biological evidence found in soil has a high failure rate due largely to the inhibitory substance humic acid (HA). Abundant in various natural soils, HA co-extracts with DNA during extraction and inhibits DNA profiling by binding to the molecular components of the genotyping assay. To successfully utilize traces of soil contaminated evidence, such as that found at many murder and rape crime scenes in South Africa, a reliable HA removal extraction system would often be selected based on previous validation studies. However, for many standard forensic DNA extraction systems, peer-reviewed publications detailing the efficacy on soil evidence is either lacking or is incomplete. Consequently, these sample types are often not collected or fail to yield suitable DNA material due to the use of unsuitable methodology. The aim of this study was to validate the common forensic DNA collection and extraction systems used in South Africa, namely DNA IQ, FTA elute and Nucleosave for processing blood and saliva contaminated with HA. A forensic appropriate volume of biological evidence was spiked with HA (0, 0.5, 1.5 and 2.5 mg/ml) and processed through each extraction protocol for the evaluation of HA removal using QPCR and STR-genotyping. The DNA IQ magnetic bead system effectively removed HA from highly contaminated blood and saliva, and generated consistently acceptable STR profiles from both artificially spiked samples and crude soil samples. This system is highly recommended for use on soil-contaminated evidence over the cellulose card-based systems currently being preferentially used for DNA sample collection. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  2. Performance of a demand controlled mechanical extract ventilation system for dwellings

    Directory of Open Access Journals (Sweden)

    I. Pollet

    2013-10-01

    Full Text Available The main aim of ventilation is to guarantee a good indoor air quality, related to the energy consumed for heating and fan(s. Active or passive heat recovery systems seem to focus on the reduction of heating consumption at the expense of fan electricity consumption and maintenance. In this study, demandcontrolled mechanical extract ventilation systems of Renson (DCV1 and DCV2, based on natural supply in the habitable rooms and mechanical extraction in the wet rooms (or even the bedrooms, was analysed for one year by means of multi-zone Contam simulations on a reference detached house and compared with standard MEV and mechanical extract ventilation systems with heat recovery (MVHR. To this end, IAQ, total energy consumption, CO2 emissions and total cost of the systems are determined. The results show that DCV systems with increased supply air flow rates or direct mechanical extract from bedrooms can significantly improve IAQ, while reducing total energy consumption compared to MEV. Applying DCV reduces primary heating energy consumption and yearly fan electricity consumption at most by 65% to 50% compared to MEV. Total operational energy costs and CO2 emissions of DCV are similar when compared to MVHR. Total costs of DCV systems over 15 years are smaller when compared to MVHR due to lower investment and maintenance costs.

  3. Extracting and standardizing medication information in clinical text - the MedEx-UIMA system.

    Science.gov (United States)

    Jiang, Min; Wu, Yonghui; Shah, Anushi; Priyanka, Priyanka; Denny, Joshua C; Xu, Hua

    2014-01-01

    Extraction of medication information embedded in clinical text is important for research using electronic health records (EHRs). However, most of current medication information extraction systems identify drug and signature entities without mapping them to standard representation. In this study, we introduced the open source Java implementation of MedEx, an existing high-performance medication information extraction system, based on the Unstructured Information Management Architecture (UIMA) framework. In addition, we developed new encoding modules in the MedEx-UIMA system, which mapped an extracted drug name/dose/form to both generalized and specific RxNorm concepts and translated drug frequency information to ISO standard. We processed 826 documents by both systems and verified that MedEx-UIMA and MedEx (the Python version) performed similarly by comparing both results. Using two manually annotated test sets that contained 300 drug entries from medication list and 300 drug entries from narrative reports, the MedEx-UIMA system achieved F-measures of 98.5% and 97.5% respectively for encoding drug names to corresponding RxNorm generic drug ingredients, and F-measures of 85.4% and 88.1% respectively for mapping drug names/dose/form to the most specific RxNorm concepts. It also achieved an F-measure of 90.4% for normalizing frequency information to ISO standard. The open source MedEx-UIMA system is freely available online at http://code.google.com/p/medex-uima/.

  4. Ant-based extraction of rules in simple decision systems over ontological graphs

    Directory of Open Access Journals (Sweden)

    Pancerz Krzysztof

    2015-06-01

    Full Text Available In the paper, the problem of extraction of complex decision rules in simple decision systems over ontological graphs is considered. The extracted rules are consistent with the dominance principle similar to that applied in the dominancebased rough set approach (DRSA. In our study, we propose to use a heuristic algorithm, utilizing the ant-based clustering approach, searching the semantic spaces of concepts presented by means of ontological graphs. Concepts included in the semantic spaces are values of attributes describing objects in simple decision systems

  5. New method to enhance the extraction yield of rutin from Sophora japonica using a novel ultrasonic extraction system by determining optimum ultrasonic frequency.

    Science.gov (United States)

    Liao, Jianqing; Qu, Baida; Liu, Da; Zheng, Naiqin

    2015-11-01

    A new method has been proposed for enhancing extraction yield of rutin from Sophora japonica, in which a novel ultrasonic extraction system has been developed to perform the determination of optimum ultrasonic frequency by a two-step procedure. This study has systematically investigated the influence of a continuous frequency range of 20-92 kHz on rutin yields. The effects of different operating conditions on rutin yields have also been studied in detail such as solvent concentration, solvent to solid ratio, ultrasound power, temperature and particle size. A higher extraction yield was obtained at the ultrasonic frequency of 60-62 kHz which was little affected under other extraction conditions. Comparative studies between existing methods and the present method were done to verify the effectiveness of this method. Results indicated that the new extraction method gave a higher extraction yield compared with existing ultrasound-assisted extraction (UAE) and soxhlet extraction (SE). Thus, the potential use of this method may be promising for extraction of natural materials on an industrial scale in the future. Copyright © 2015 Elsevier B.V. All rights reserved.

  6. Automatic knowledge extraction in sequencing analysis with multiagent system and grid computing.

    Science.gov (United States)

    González, Roberto; Zato, Carolina; Benito, Rocío; Bajo, Javier; Hernández, Jesús M; De Paz, Juan F; Vera, Vicente; Corchado, Juan M

    2012-12-01

    Advances in bioinformatics have contributed towards a significant increase in available information. Information analysis requires the use of distributed computing systems to best engage the process of data analysis. This study proposes a multiagent system that incorporates grid technology to facilitate distributed data analysis by dynamically incorporating the roles associated to each specific case study. The system was applied to genetic sequencing data to extract relevant information about insertions, deletions or polymorphisms.

  7. Automatic knowledge extraction in sequencing analysis with multiagent system and grid computing

    Directory of Open Access Journals (Sweden)

    González Roberto

    2012-12-01

    Full Text Available Advances in bioinformatics have contributed towards a significant increase in available information. Information analysis requires the use of distributed computing systems to best engage the process of data analysis. This study proposes a multiagent system that incorporates grid technology to facilitate distributed data analysis by dynamically incorporating the roles associated to each specific case study. The system was applied to genetic sequencing data to extract relevant information about insertions, deletions or polymorphisms.

  8. Extracting foreground ensemble features to detect abnormal crowd behavior in intelligent video-surveillance systems

    Science.gov (United States)

    Chan, Yi-Tung; Wang, Shuenn-Jyi; Tsai, Chung-Hsien

    2017-09-01

    Public safety is a matter of national security and people's livelihoods. In recent years, intelligent video-surveillance systems have become important active-protection systems. A surveillance system that provides early detection and threat assessment could protect people from crowd-related disasters and ensure public safety. Image processing is commonly used to extract features, e.g., people, from a surveillance video. However, little research has been conducted on the relationship between foreground detection and feature extraction. Most current video-surveillance research has been developed for restricted environments, in which the extracted features are limited by having information from a single foreground; they do not effectively represent the diversity of crowd behavior. This paper presents a general framework based on extracting ensemble features from the foreground of a surveillance video to analyze a crowd. The proposed method can flexibly integrate different foreground-detection technologies to adapt to various monitored environments. Furthermore, the extractable representative features depend on the heterogeneous foreground data. Finally, a classification algorithm is applied to these features to automatically model crowd behavior and distinguish an abnormal event from normal patterns. The experimental results demonstrate that the proposed method's performance is both comparable to that of state-of-the-art methods and satisfies the requirements of real-time applications.

  9. Energy extraction from a large-scale microbial fuel cell system treating municipal wastewater

    Science.gov (United States)

    Ge, Zheng; Wu, Liao; Zhang, Fei; He, Zhen

    2015-11-01

    Development of microbial fuel cell (MFC) technology must address the challenges associated with energy extraction from large-scale MFC systems consisting of multiple modules. Herein, energy extraction is investigated with a 200-L MFC system (effective volume of 100 L for this study) treating actual municipal wastewater. A commercially available energy harvesting device (BQ 25504) is used successfully to convert 0.8-2.4 V from the MFCs to 5 V for charging ultracapacitors and running a DC motor. Four different types of serial connection containing different numbers of MFC modules are examined for energy extraction and conversion efficiency. The connection containing three rows of the MFCs has exhibited the best performance with the highest power output of ∼114 mW and the conversion efficiency of ∼80%. The weak performance of one-row MFCs negatively affects the overall performance of the connected MFCs in terms of both energy production and conversion. Those results indicate that an MFC system with balanced performance among individual modules will be critical to energy extraction. Future work will focus on application of the extracted energy to support MFC operation.

  10. Advances in passive-remote and extractive Fourier transform infrared spectroscopic systems

    International Nuclear Information System (INIS)

    Demirgian, J.C.; Hammer, C.; Hwang, E.; Mao, Zhuoxiong.

    1993-01-01

    The Clean Air Act of 1990 requires the monitoring of air toxics including those from incinerator emissions. Continuous emission monitors (CEM) would demonstrate the safety of incinerators and address public concern about emissions of hazardous organic compounds. Fourier transform infrared (FTIR) spectroscopy can provide the technology for continuous emission monitoring of stacks. Stack effluent can be extracted and analyzed in less than one minute with conventional FTIR spectrometers. Passive-remote FTIR spectrometers can detect certain emission gases over 1 km away from a stack. The authors discuss advances in both extractive and passive-remote FTIR technology. Extractive systems are being tested with EPA protocols, which will soon replace periodic testing methods. Standard operating procedures for extractive systems are being developed and tested. Passive-remote FTIR spectrometers have the advantage of not requiring an extracted sample; however, they have less sensitivity. We have evaluated the ability of commercially available systems to detect fugitive plumes and to monitor carbon monoxide at a coal-fired power plant

  11. The general properties of water - nitrobenzene - crown - bis-1,2-dicarbollylcobaltate extraction systems

    International Nuclear Information System (INIS)

    Vanura, P.

    2003-01-01

    The extraction and stability constants in the system water - nitrobenzene have been collected and general rules valid for water - nitrobenzene - crown - bis-1,2-dicarbollylcobaltate extraction system have been found. The main principles are size compatibility of ion diameter and crown cavity diameters, the flexibility of crown, the basicity of crown and the steric factor of both the ligand and the extracted ion. The extraction in the system water - mineral acid or salt polyoxyethylene compound - bis-1,2-dicarbollylcobaltate - nitrobenzene is more complicated than can be expected from usually used ion diameter - crown cavity diameter compatibility principle. The other important factors are the basicity and the deformability of crown, steric aspect and the angles of bonds of extracted ion. The binuclear 'sandwich' complexes with H + ion and Sr 2+ or Ba 2+ ions have been proved for dibenzo-18-crown-6 (DB18C6). On the other hand, only SrL 2 and BaL 2 (L = 15C5) complexes are formed in nitrobenzene saturated with water. The addition of polyoxyethylene compound usually increases the distribution ratio of alkali earth metal ions and the selectivity of its mutual separation. (authors)

  12. Extraction of Oxytetracycline Hydrochloride in Aqueous Two-phase System of Acetone and Ammonium Sulfate

    International Nuclear Information System (INIS)

    Han, J.

    2013-01-01

    Summary: Aqueous two-phase system (ATPS) is an efficient implement for separation of various substrates, and extracted by an aqueous two-phase system has been successful ly applied in the downstream processing of various biological compounds. In this research, the extraction of oxytetracycline hydrochloride (OTC-HCl) was carried out in an aqueous two-phase system containing acetone and ammonium sulfate solution, which partitioned the antibiotic to the upper phase. The effects of some parameters on the extraction efficiency of OTC-HCl were studied in detail, including temperature, the volume of acetone, the pH value of ammonium sulfate solution, the concentrations of (NH/sub 4/)/sub 2/ SO/sub 4/ and OTC-HCl. The results showed that the volume of acetone, the pH value of ammonium sulfate solution and the concentration of OTC-HCl in feed had significant effects on the extraction efficiency of OTC-HCl, but the effects of temperature on the extraction of OTC-HCl was not obvious. (author)

  13. Sawtooth first phase biphasic defibrillation waveform: a comparison with standard waveform in clinical devices.

    Science.gov (United States)

    Yamanouchi, Y; Brewer, J E; Mowrey, K A; Kroll, M W; Donohoo, A M; Wilkoff, B L; Tchou, P J

    1997-05-01

    A major limitation in a conventional truncated exponential waveform is the rapid drop in current that results in short duration of high current or longer duration with a lower average current. We hypothesized that increasing the first phase average current by boosting the decaying waveform prior to phase reversal may improve defibrillation efficacy. To better simulate a "rectangular" waveform during the first phase, a "sawtooth" defibrillation waveform was constructed using "parallel-series" switching of capacitances (each 30 microF) during the first phase. This permitted a boost in the voltage late in the first phase. This sawtooth biphasic waveform (sawtooth) was compared to two clinical waveforms: a 135-microF capacitance (control-1) and a 90-microF capacitance (control-2) waveform. Defibrillation threshold (DFT) parameters were evaluated in 13 anesthetized pig models using a system consisting of a transvenous right ventricular apex lead (anode) and a left pectoral "hot can" electrode (cathode) system. DFT was determined by a "down-up down-up" protocol. The stored energy for sawtooth, control-1, and control-2 was 10.5 +/- 2.8 J, 12.3 +/- 3.7 J*, and 12.2 +/- 2.8 J*, respectively (*P series" switching system of smaller capacitors can improve defibrillation efficacy. A higher average current in the first phase generated by such a waveform may contribute to more efficient defibrillation by facilitating myocyte capture.

  14. Recognition of a Phase-Sensitivity OTDR Sensing System Based on Morphologic Feature Extraction.

    Science.gov (United States)

    Sun, Qian; Feng, Hao; Yan, Xueying; Zeng, Zhoumo

    2015-06-29

    This paper proposes a novel feature extraction method for intrusion event recognition within a phase-sensitive optical time-domain reflectometer (Φ-OTDR) sensing system. Feature extraction of time domain signals in these systems is time-consuming and may lead to inaccuracies due to noise disturbances. The recognition accuracy and speed of current systems cannot meet the requirements of Φ-OTDR online vibration monitoring systems. In the method proposed in this paper, the time-space domain signal is used for feature extraction instead of the time domain signal. Feature vectors are obtained from morphologic features of time-space domain signals. A scatter matrix is calculated for the feature selection. Experiments show that the feature extraction method proposed in this paper can greatly improve recognition accuracies, with a lower computation time than traditional methods, i.e., a recognition accuracy of 97.8% can be achieved with a recognition time of below 1 s, making it is very suitable for Φ-OTDR system online vibration monitoring.

  15. Arrhythmia Classification Based on Multi-Domain Feature Extraction for an ECG Recognition System.

    Science.gov (United States)

    Li, Hongqiang; Yuan, Danyang; Wang, Youxi; Cui, Dianyin; Cao, Lu

    2016-10-20

    Automatic recognition of arrhythmias is particularly important in the diagnosis of heart diseases. This study presents an electrocardiogram (ECG) recognition system based on multi-domain feature extraction to classify ECG beats. An improved wavelet threshold method for ECG signal pre-processing is applied to remove noise interference. A novel multi-domain feature extraction method is proposed; this method employs kernel-independent component analysis in nonlinear feature extraction and uses discrete wavelet transform to extract frequency domain features. The proposed system utilises a support vector machine classifier optimized with a genetic algorithm to recognize different types of heartbeats. An ECG acquisition experimental platform, in which ECG beats are collected as ECG data for classification, is constructed to demonstrate the effectiveness of the system in ECG beat classification. The presented system, when applied to the MIT-BIH arrhythmia database, achieves a high classification accuracy of 98.8%. Experimental results based on the ECG acquisition experimental platform show that the system obtains a satisfactory classification accuracy of 97.3% and is able to classify ECG beats efficiently for the automatic identification of cardiac arrhythmias.

  16. Solvent. I. Extraction systems applied to uranium analysis. I. Extraction studies with Tributyl phosphate-Methyl-isobutyl-ketone

    International Nuclear Information System (INIS)

    Vera Palomino, J.; Palomares Delgado, F.; Petrement Eguiluz, J. C.

    1964-01-01

    A factorial study of the selective extraction of uranium with a mixture of TBP-MIC was carried out using 0,8 N nitric acid and different salting agents. We use the most suitable salting agent to develop new factorial experiments in order to get an equation involving the percent of extracted uranium, E, the concentration of the extraction agent in the organic phase, c, and the concentration of the slating agent in the aqueous phase, n. (Author) 3 refs

  17. Application of analytic hierarchy process to extract the user's purpose of expert systems

    International Nuclear Information System (INIS)

    Gofuku, Akio; Wakabayashi, Jiro; Morimoto, Takashi.

    1992-01-01

    This paper deals with an application of analytic hierarchy process (AHP) to extract the user's purpose which must be input to expert systems. In the AHP, the process to obtain the weights for criteria by pairwise comparisons is interpreted as the extraction of the decision marker's idea about the importance of each criterion. With this interpretation, the analytic hierarchy process is applied to extract the analyst's idea of the weights of several factors to select constitutive equations suitable for a target analysis in a model selection support expert system under development for numerical simulation of nuclear thermal-hydraulics; the constitutive equations are ordinary introduced in a liquid-vapor two-phase flow analysis. Furthermore, an algorithm by applying the graph theory is shown to evaluate covering condition to obtain the weights from incomplete pairwise comparisons. (author)

  18. Antioxidant effect of seaweed extracts in food emulsion systems enriched with fish oil

    DEFF Research Database (Denmark)

    Larsen, Ditte Baun; Farvin, Sabeena; Jacobsen, Charlotte

    a wide range of polyphenols with potential antioxidant activity. Thus, in vitro antioxidant properties of F. vesiculosus extracts have been found to be related to the total polyphenolic content. It has been suggested that the primary antioxidant activity comes from secondary metabolites......Natural antioxidants derived from marine algae have a high content of bioactive components with potential for improving oxidative stability of lipids in food systems. In this presentation we will discuss results from our ongoing work on the brown algae Fucus vesiculosus. This seaweed contains...... such as phlorotannins, a dominant polyphenolic compound. However, studies on the effectiveness of seaweed extracts in food model systems are sparse, therefore there is a need to look further into this area. Results obtained in our lab with different extracts of F. Vesiculosus in a range of different food models...

  19. Preliminary design of the pulse generator for the CLIC damping ring extraction system

    CERN Document Server

    Holma, Janne; Ovaska, Seppo

    2011-01-01

    The spent drive beam must be cleanly extracted and bent away from the decelerator axis at the end of each CLIC decelerator in order to leave space for injecting a fresh beam train in the next sector. Then the spent beam must be safely absorbed. A compact extraction system made of a single dipole is proposed. The spent beam is driven to a water dump located at 20m downstream of the extraction point and transversely 6m away of the axis of the main linac. An adequate spread of the beam impact map on the dump offers small temperature excursions in both the dump and its entrance window, allowing for reliable operation and a long lifetime of the system.

  20. Enzyme mass-transfer coefficient in aqueous two-phase systems using static mixer extraction column.

    Science.gov (United States)

    Rostami, K; Alamshahi, M

    2002-09-01

    Recent technical advances in aqueous two-phase systems (ATPS) have made this a sound technique for the extraction of biomacromolecules. The extraction of alpha-amylase was investigated using aqueous two-phase systems formed by sodium sulphate-polyethylene glycol (PEG) in water in a 47-mm inner diameter spray column packed with three types of static mixers. The effects of dispersed-phase flow rate, phase composition, column height and diameter were studied. The extraction column was operated in a semi-batch manner. It was found that the hold-up and volumetric mass transfer coefficients increased with an increase in dispersed (PEG-rich) phase velocity and decreased with increasing phase composition. Empirical correlations were developed for fractional dispersed-phase hold-up and volumetric mass transfer coefficients.

  1. A neuro-fuzzy system for extracting environment features based on ultrasonic sensors.

    Science.gov (United States)

    Marichal, Graciliano Nicolás; Hernández, Angela; Acosta, Leopoldo; González, Evelio José

    2009-01-01

    In this paper, a method to extract features of the environment based on ultrasonic sensors is presented. A 3D model of a set of sonar systems and a workplace has been developed. The target of this approach is to extract in a short time, while the vehicle is moving, features of the environment. Particularly, the approach shown in this paper has been focused on determining walls and corners, which are very common environment features. In order to prove the viability of the devised approach, a 3D simulated environment has been built. A Neuro-Fuzzy strategy has been used in order to extract environment features from this simulated model. Several trials have been carried out, obtaining satisfactory results in this context. After that, some experimental tests have been conducted using a real vehicle with a set of sonar systems. The obtained results reveal the satisfactory generalization properties of the approach in this case.

  2. A Neuro-Fuzzy System for Extracting Environment Features Based on Ultrasonic Sensors

    Directory of Open Access Journals (Sweden)

    Evelio José González

    2009-12-01

    Full Text Available In this paper, a method to extract features of the environment based on ultrasonic sensors is presented. A 3D model of a set of sonar systems and a workplace has been developed. The target of this approach is to extract in a short time, while the vehicle is moving, features of the environment. Particularly, the approach shown in this paper has been focused on determining walls and corners, which are very common environment features. In order to prove the viability of the devised approach, a 3D simulated environment has been built. A Neuro-Fuzzy strategy has been used in order to extract environment features from this simulated model. Several trials have been carried out, obtaining satisfactory results in this context. After that, some experimental tests have been conducted using a real vehicle with a set of sonar systems. The obtained results reveal the satisfactory generalization properties of the approach in this case.

  3. The Development and the Evaluation of a System for Extracting Events from Web Pages

    Directory of Open Access Journals (Sweden)

    Mihai-Constantin AVORNICULUI

    2010-01-01

    Full Text Available The centralization of a particular event is primarily useful for running news services. These services should provide updated information, if possible even in real time, on a specific type of event. These events and their extraction involved the automatic analysis of linguistic structure documents to determine the possible sequences in which these events occur in documents. This analysis will provide structured and semi-structured documents in which the unit events can be extracted automatically. In order to measure the quality of a system, a methodology will be introduced, which describes the stages and how the decomposition of a system for extracting events in components, quality attributes and properties will be defined for these components, and finally will be introduced metrics for evaluation.

  4. The extraction of uranium from wet process phosphoric acid using a liquid surfactant membrane system

    International Nuclear Information System (INIS)

    Dickens, N.; Davies, G.A.

    1984-01-01

    A liquid membrane extraction process is examined for the extraction of uranium from wet process phosphoric acid. Uranium is present in the acid in concentrations up to 100 ppm which in principle makes it ideal for treatment with a membrane process. The membrane system studied is based on extraction using DEHPA-TOPO reagents which are contained within the organic phase of a water in oil emulsion. Formulations of the emulsion membrane system have been studied, the limitations of acid temperature, P 2 O 5 concentration and solid dispersed impurities in the acid have been studied in laboratory batch experiments and in a continuous pilot plant unit capable of treating 5l of concentrated acid per minute. Data from the pilot plant work has been used to develop a flowsheet for a commercial unit based on this process. (author)

  5. Leaf-Cutter Ant Fungus Gardens Are Biphasic Mixed Microbial Bioreactors That Convert Plant Biomass to Polyols with Biotechnological Applications

    Science.gov (United States)

    Somera, Alexandre F.; Lima, Adriel M.; dos Santos-Neto, Álvaro J.; Lanças, Fernando M.

    2015-01-01

    Leaf-cutter ants use plant matter to culture the obligate mutualistic basidiomycete Leucoagaricus gongylophorus. This fungus mediates ant nutrition on plant resources. Furthermore, other microbes living in the fungus garden might also contribute to plant digestion. The fungus garden comprises a young sector with recently incorporated leaf fragments and an old sector with partially digested plant matter. Here, we show that the young and old sectors of the grass-cutter Atta bisphaerica fungus garden operate as a biphasic solid-state mixed fermenting system. An initial plant digestion phase occurred in the young sector in the fungus garden periphery, with prevailing hemicellulose and starch degradation into arabinose, mannose, xylose, and glucose. These products support fast microbial growth but were mostly converted into four polyols. Three polyols, mannitol, arabitol, and inositol, were secreted by L. gongylophorus, and a fourth polyol, sorbitol, was likely secreted by another, unidentified, microbe. A second plant digestion phase occurred in the old sector, located in the fungus garden core, comprising stocks of microbial biomass growing slowly on monosaccharides and polyols. This biphasic operation was efficient in mediating symbiotic nutrition on plant matter: the microbes, accounting for 4% of the fungus garden biomass, converted plant matter biomass into monosaccharides and polyols, which were completely consumed by the resident ants and microbes. However, when consumption was inhibited through laboratory manipulation, most of the plant polysaccharides were degraded, products rapidly accumulated, and yields could be preferentially switched between polyols and monosaccharides. This feature might be useful in biotechnology. PMID:25911490

  6. Feasibility of Injection/Extraction Systems for Muon FFAG Rings in the Neutrino Factory

    International Nuclear Information System (INIS)

    Pasternak, J.; Berg, J.; Aslaninejad, M.; Kelliher, D.; Machida, S.

    2010-01-01

    Non-scaling FFAG rings have been proposed for muon acceleration in a neutrino factory. In order to achieve small orbit excursion and small time of flight variation, lattices with a very compact cell structure and short straight sections are required. The resulting geometry places very challenging constraints on the injection/extraction systems. The feasibility of injection/extraction is discussed and various implementations focusing on minimization of kicker/septum strength are presented. The injection and extraction systems in the nonscaling FFAG for muon acceleration in a neutrino factory were studied in the ring based on FODO lattice. The vertical direction was found to be preferential for both injection and extraction, which allows for lower kicker strengths and facilitates the distribution of kickers due to a lower phase advance per cell in comparison with the horizontal plane. It is possible to design mirror-symmetric schemes in which the kickers can be reused for both signs of muons. The disadvantage of these solutions is a need for special magnets with large aperture in the injection/extraction region due to the large kicked beam oscillations. The strengths of the required kickers are still very challenging and the fields in the septum magnets dictates the need for a superconducting design.

  7. Design and evaluation of lornoxicam bilayered tablets for biphasic release

    Directory of Open Access Journals (Sweden)

    Songa Ambedkar Sunil

    2012-12-01

    Full Text Available The objective of the present investigation was to develop bilayered tablets of lornoxicam to achieve biphasic release pattern. A bilayered tablet, consisting of an immediate and controlled release layer, was prepared by direct compression technique. The controlled release effect was achieved by using various hydrophilic natural, semi synthetic and synthetic controlled release polymers such as xanthan gum, hydroxypropyl methylcellulose (HPMC and polyethylene oxide (PEO to modulate the release of the drug. The in vitro drug release profiles showed the biphasic release behavior in which the immediate release (IR layer containing the lornoxicam was released within 15 minutes, whereas the controlled release (CR layer controlled the drug release for up to 24 h. All the bilayered tablets formulated have followed the zero order release with non-Fickian diffusion controlled release mechanism after the initial burst release. FTIR studies revealed that there was no interaction between the drug and polymers used in the study. Statistical analysis (ANOVA showed no significant difference in the cumulative amount of drug release after 15 min, but significant difference (p O objetivo do presente trabalho foi desenvolver comprimidos bicamada de lornoxicam para atingir padrão de liberação bifásica. Preparou-se, por compressão direta, comprimido bicamada, consistindo de uma camada de liberação imediata e uma de liberação controlada. A liberação controlada foi obtida pelo uso de vários polímeros naturais hidrofílicos, semi-sintéticos e sintéticos, tais como goma xantana, hidroxipropilmetil celulose (HPMC e óxido de polietileno (PEO para modular a liberação do fármaco. Os perfis de liberação in vitro mostraram comportamento bifásico em que a camada de liberação imediata (IR contendo lornoxicam foi liberada em 15 minutos, enquanto a camada de liberação controlada (CR liberou o fármaco em mais de 24 horas, Todos os comprimidos bicamada

  8. Micro-Lid For Sealing Sample Reservoirs of micro-Extraction Systems

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop a proof-of-concept micro-Lid (µLid) to tightly seal a micro-sampler or micro-extraction system. Fabrication of µLid would be conducted in the...

  9. Some Central Nervous System Effects of the aqueous Extract of the ...

    African Journals Online (AJOL)

    The leaves of Phyllanthus amarus is used in Southern Nigeria to treat variety of diseases including epilepsy. The aqueous extract of the leaves of Phyllanthus amarus was investigated for some central nervous system effects. Two animals models (maximal electroshock and pentylenetetrazol-induced convulsion), were used ...

  10. Biphasic Peptide Amphiphile Nanomatrix Embedded with Hydroxyapatite Nanoparticles for Stimulated Osteoinductive Response

    Science.gov (United States)

    Anderson, Joel M.; Patterson, Jessica L.; Vines, Jeremy B.; Javed, Amjad; Gilbert, Shawn R.; Jun, Ho-Wook

    2013-01-01

    Formation of the native bone extracellular matrix (ECM) provides an attractive template for bone tissue engineering. The structural support and biological complexity of bone ECM are provided within a composite microenvironment that consists of an organic fibrous network reinforced by inorganic hydroxyapatite (HA) nanoparticles. Recreating this biphasic assembly, a bone ECM analogous scaffold comprised of self-assembling peptide amphiphile (PA) nanofibers and interspersed HA nanoparticles was investigated. PAs were endowed with biomolecular ligand signaling using a synthetically inscribed peptide sequence (i.e. RGDS) and integrated with HA nanoparticles to form a biphasic nanomatrix hydrogel. It was hypothesized the biphasic hydrogel would induce osteogenic differentiation of human mesenchymal stem cells (hMSCs) and improve bone healing as mediated by RGDS ligand signaling within PA nanofibers and embedded HA mineralization source. Viscoelastic stability of the biphasic PA hydrogels was evaluated with different weight concentrations of HA for improved gelation. After demonstrating initial viability, long-term cellularity and osteoinduction of encapsulated hMSCs in different PA hydrogels were studied in vitro. Temporal progression of osteogenic maturation was assessed by gene expression of key markers. A preliminary animal study demonstrated bone healing capacity of the biphasic PA nanomatrix under physiological conditions using a critical size femoral defect rat model. The combination of RGDS ligand signaling and HA nanoparticles within the biphasic PA nanomatrix hydrogel demonstrated the most effective osteoinduction and comparative bone healing response. Therefore, the biphasic PA nanomatrix establishes a well-organized scaffold with increased similarity to natural bone ECM with the prospect for improved bone tissue regeneration. PMID:22077993

  11. Biphasic functions for the GDNF-Ret signaling pathway in chemosensory neuron development and diversification.

    Science.gov (United States)

    Donnelly, Christopher R; Shah, Amol A; Mistretta, Charlotte M; Bradley, Robert M; Pierchala, Brian A

    2018-01-16

    The development of the taste system relies on the coordinated regulation of cues that direct the simultaneous development of both peripheral taste organs and innervating sensory ganglia, but the underlying mechanisms remain poorly understood. In this study, we describe a novel, biphasic function for glial cell line-derived neurotrophic factor (GDNF) in the development and subsequent diversification of chemosensory neurons within the geniculate ganglion (GG). GDNF, acting through the receptor tyrosine kinase Ret, regulates the expression of the chemosensory fate determinant Phox2b early in GG development. Ret -/- mice, but not Ret fx/fx ; Phox2b -Cre mice, display a profound loss of Phox2b expression with subsequent chemosensory innervation deficits, indicating that Ret is required for the initial amplification of Phox2b expression but not its maintenance. Ret expression is extinguished perinatally but reemerges postnatally in a subpopulation of large-diameter GG neurons expressing the mechanoreceptor marker NF200 and the GDNF coreceptor GFRα1. Intriguingly, we observed that ablation of these neurons in adult Ret -Cre/ER T2 ; Rosa26 LSL-DTA mice caused a specific loss of tactile, but not chemical or thermal, electrophysiological responses. Overall, the GDNF-Ret pathway exerts two critical and distinct functions in the peripheral taste system: embryonic chemosensory cell fate determination and the specification of lingual mechanoreceptors. Copyright © 2018 the Author(s). Published by PNAS.

  12. Inverted supercritical carbon dioxide/aqueous biphasic media for rhodium-catalyzed hydrogenation reactions.

    Science.gov (United States)

    Burgemeister, Katja; Franciò, Giancarlo; Gego, Volker H; Greiner, Lasse; Hugl, Herbert; Leitner, Walter

    2007-01-01

    An inverted supercritical carbon dioxide (scCO(2))/aqueous biphasic system has been used as reaction media for Rh-catalysed hydrogenation of polar substrates. Chiral and achiral CO(2)-philic catalysts were efficiently immobilised in scCO(2) as the stationary phase, while the polar substrates and products were contained in water as the mobile phase. Notably, product separation and catalyst recycling were conducted without depressurisation of the autoclave. The catalyst phase was reused several times with high conversion and product recovery of more than 85 %. Loss of rhodium and phosphorus by leaching were found to be below the detection limit after the first two cycles in the majority of repetitive experiments. The reaction conditions were optimised with a minimum of experiments by using a simplex algorithm in a sequential optimisation. Total turnover numbers (TTNs) of up to 1600, turnover frequencies (TOFs) of up to 340 h(-1) and ee's up to 99 % were obtained in repetitive batch operations. The scope of the devised catalytic system has been investigated and a semicontinuous reaction setup has been implemented. The chiral ligand (R,S)-3-H(2)F(6)-BINAPHOS allowed highly enantioselective hydrogenation of itaconic acid and methyl-2-acetamidoacrylate combined with a considerable catalyst stability in these reaction media.

  13. The extraction of Zn(II in aqueous PEG (1550 – (NH42SO4 two-phase system using Cl– ions as extracting agent

    Directory of Open Access Journals (Sweden)

    DUMITRU BULGARIU

    2007-03-01

    Full Text Available The extraction of Zn(II in an aqueous PEG (1550 – (NH42SO4 two-phase system as a function of several experimental parameters was studied. PEG-based aqueous two-phase systems are composed of two immiscible phases: a polymer-rich phase and a salt-rich phase, which can be used for extraction experiments. In the absence of a suitable extracting agent, for the system consisting of a mixture of equal volumes of 40 mass% PEG and 40 mass% (NH42SO4 aqueous solutions, Zn(II remained predominantly in the salt-rich phase. Variation of the pH of the salt stock solution did not change very much the extraction efficiency. By adding chloride ions, an enhancement of the Zn(II extraction was observed. The Zn(II extraction efficiency in presence of Cl- depends on the acidity of the salt stock solution and on the concentration of chloride ions added into the system.

  14. Extractables characterization for five materials of construction representative of packaging systems used for parenteral and ophthalmic drug products.

    Science.gov (United States)

    Jenke, Dennis; Castner, James; Egert, Thomas; Feinberg, Tom; Hendricker, Alan; Houston, Christopher; Hunt, Desmond G; Lynch, Michael; Shaw, Arthur; Nicholas, Kumudini; Norwood, Daniel L; Paskiet, Diane; Ruberto, Michael; Smith, Edward J; Holcomb, Frank

    2013-01-01

    Polymeric and elastomeric materials are commonly encountered in medical devices and packaging systems used to manufacture, store, deliver, and/or administer drug products. Characterizing extractables from such materials is a necessary step in establishing their suitability for use in these applications. In this study, five individual materials representative of polymers and elastomers commonly used in packaging systems and devices were extracted under conditions and with solvents that are relevant to parenteral and ophthalmic drug products (PODPs). Extraction methods included elevated temperature sealed vessel extraction, sonication, refluxing, and Soxhlet extraction. Extraction solvents included a low-pH (pH = 2.5) salt mixture, a high-pH (pH = 9.5) phosphate buffer, a 1/1 isopropanol/water mixture, isopropanol, and hexane. The resulting extracts were chemically characterized via spectroscopic and chromatographic means to establish the metal/trace element and organic extractables profiles. Additionally, the test articles themselves were tested for volatile organic substances. The results of this testing established the extractables profiles of the test articles, which are reported herein. Trends in the extractables, and their estimated concentrations, as a function of the extraction and testing methodologies are considered in the context of the use of the test article in medical applications and with respect to establishing best demonstrated practices for extractables profiling of materials used in PODP-related packaging systems and devices. Plastic and rubber materials are commonly encountered in medical devices and packaging/delivery systems for drug products. Characterizing the extractables from these materials is an important part of determining that they are suitable for use. In this study, five materials representative of plastics and rubbers used in packaging and medical devices were extracted by several means, and the extracts were analytically

  15. Core-shell nanoreactors for efficient aqueous biphasic catalysis.

    Science.gov (United States)

    Zhang, Xuewei; Cardozo, Andrés F; Chen, Si; Zhang, Wenjing; Julcour, Carine; Lansalot, Muriel; Blanco, Jean-François; Gayet, Florence; Delmas, Henri; Charleux, Bernadette; Manoury, Eric; D'Agosto, Franck; Poli, Rinaldo

    2014-11-17

    Water-borne phosphine-functionalized core-cross-linked micelles (CCM) consisting of a hydrophobic core and a hydrophilic shell were obtained as stable latexes by reversible addition-fragmentation chain transfer (RAFT) in water in a one-pot, three-step process. Initial homogeneous aqueous-phase copolymerization of methacrylic acid (MAA) and poly(ethylene oxide) methyl ether methacrylate (PEOMA) is followed by copolymerization of styrene (S) and 4-diphenylphosphinostyrene (DPPS), yielding P(MAA-co-PEOMA)-b-P(S-co-DPPS) amphiphilic block copolymer micelles (M) by polymerization-induced self-assembly (PISA), and final micellar cross-linking with a mixture of S and diethylene glycol dimethacrylate. The CCM were characterized by dynamic light scattering and NMR spectroscopy to evaluate size, dispersity, stability, and the swelling ability of various organic substrates. Coordination of [Rh(acac)(CO)2 ] (acac=acetylacetonate) to the core-confined phosphine groups was rapid and quantitative. The CCM and M latexes were then used, in combination with [Rh(acac)(CO)2 ], to catalyze the aqueous biphasic hydroformylation of 1-octene, in which they showed high activity, recyclability, protection of the activated Rh center by the polymer scaffold, and low Rh leaching. The CCM latex gave slightly lower catalytic activity but significantly less Rh leaching than the M latex. A control experiment conducted in the presence of the sulfoxantphos ligand pointed to the action of the CCM as catalytic nanoreactors with substrate and product transport into and out of the polymer core, rather than as a surfactant in interfacial catalysis. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Production of 93mMo through natY(7Li, 3n) reaction and subsequent studies on separation and extraction behaviour of no-carrier-added 93mMo from an yttrium target

    International Nuclear Information System (INIS)

    Nayak, Dalia; Lahiri, Susanta

    2008-01-01

    The present work reports heavy-ion-assisted production of 93m Mo from a natural yttrium target using the 89 Y( 7 Li, 3n) 93m Mo reaction. Three different methodologies based on liquid-liquid extraction (LLX), aqueous biphasic extraction and precipitation, have been developed for separation and extraction of no-carrier-added (nca) 93m Mo (T 1/2 =6.85 h) radionuclide from bulk yttrium target. Complete separation of nca Mo from the target Y has been achieved by employing LLX technique with 0.1 M trioctylamine (TOA) dissolved in cyclohexane and 8 M HCl. Quantitative separation of 93m Mo from the yttrium target is also possible by precipitating bulk yttrium with 1 M oxalic acid. However, for this particular case, studies have shown that the aqueous biphasic extraction is not the method of choice for separation of nca Mo. Nevertheless, the extraction pattern is important in the context of simulation experiments for studying the behaviour of 106 Sg. Similarity or dissimilarity between the extraction patterns in various analytical systems will be helpful to decisively place Sg in the right position in the periodic table

  17. Ascending-ramp biphasic waveform has a lower defibrillation threshold and releases less troponin I than a truncated exponential biphasic waveform.

    Science.gov (United States)

    Huang, Jian; Walcott, Gregory P; Ruse, Richard B; Bohanan, Scott J; Killingsworth, Cheryl R; Ideker, Raymond E

    2012-09-11

    We tested the hypothesis that the shape of the shock waveform affects not only the defibrillation threshold but also the amount of cardiac damage. Defibrillation thresholds were determined for 11 waveforms-3 ascending-ramp waveforms, 3 descending-ramp waveforms, 3 rectilinear first-phase biphasic waveforms, a Gurvich waveform, and a truncated exponential biphasic waveform-in 6 pigs with electrodes in the right ventricular apex and superior vena cava. The ascending, descending, and rectilinear waveforms had 4-, 8-, and 16-millisecond first phases and a 3.5-millisecond rectilinear second phase that was half the voltage of the first phase. The exponential biphasic waveform had a 60% first-phase and a 50% second-phase tilt. In a second study, we attempted to defibrillate after 10 seconds of ventricular fibrillation with a single ≈30-J shock (6 pigs successfully defibrillated with 8-millisecond ascending, 8-millisecond rectilinear, and truncated exponential biphasic waveforms). Troponin I blood levels were determined before and 2 to 10 hours after the shock. The lowest-energy defibrillation threshold was for the 8-milliseconds ascending ramp (14.6±7.3 J [mean±SD]), which was significantly less than for the truncated exponential (19.6±6.3 J). Six hours after shock, troponin I was significantly less for the ascending-ramp waveform (0.80±0.54 ng/mL) than for the truncated exponential (1.92±0.47 ng/mL) or the rectilinear waveform (1.17±0.45 ng/mL). The ascending ramp has a significantly lower defibrillation threshold and at ≈30 J causes 58% less troponin I release than the truncated exponential biphasic shock. Therefore, the shock waveform affects both the defibrillation threshold and the amount of cardiac damage.

  18. An Ascending Ramp Biphasic Waveform Has a Lower Defibrillation Threshold and Releases Less Troponin I Than a Truncated Exponential Biphasic Waveform

    Science.gov (United States)

    Huang, Jian; Walcott, Gregory P.; Ruse, Richard B.; Bohanan, Scott J.; Killingsworth, Cheryl R.; Ideker, Raymond E.

    2014-01-01

    Background We tested the hypothesis that the shape of the shock waveform affects not only the defibrillation threshold (DFT), but also the amount of cardiac damage. Methods and Results DFTs were determined for 11 waveforms: 3 ascending ramp, 3 descending ramp, and 3 rectilinear first phase biphasic waveforms, a Gurvich waveform, and a truncated exponential biphasic waveform in 6 pigs with electrodes in the RV apex and SVC. The ascending, descending and rectilinear waveforms had 4, 8 and 16 ms 1st phases and a 3.5 ms 2nd rectilinear phase half the voltage of the 1st phase. The exponential biphasic waveform had a 60% 1st phase and a 50% 2nd phase tilt. In a second study, we attempted to defibrillate after 10 s of VF with a single ≈ 30 J shock (6 pigs successfully defibrillated with 8 ms ascending, 8 ms rectilinear wave and truncated exponential biphasic waveforms). Troponin I blood levels were determined before and 2 to 10 hrs after the shock. The lowest energy DFT was for the 8 ms ascending ramp (14.6±7.3 SD J), which was significantly less than for the truncated exponential (19.6±6.3 J). Six hours postshock, troponin I in ng/ml was significantly less for the ascending ramp (0.80±0.54) than for the truncated exponential (1.92±0.47) or the rectilinear waveform (1.17 ±0.45). Conclusions The ascending ramp has a significantly lower DFT, and at ≈ 30 J causes 58% less troponin I release than the truncated exponential biphasic shock. Therefore, the shock waveform affects both the DFT and the amount of cardiac damage. PMID:22865891

  19. Dual Pump Recovery (DPR System to Extract Freshwater in Coastal Aquifers

    Directory of Open Access Journals (Sweden)

    C. Otto

    2002-06-01

    Full Text Available The paper describes the hydraulic theory of recovering a dense plume using a newly devised dual pump recover system (DPR and its feasibility to half the remediation time of a contaminated unconfined aquifer in a coastal urban environment. Although the DPR system was successfully applied to clean up the polluted aquifer, the hydraulic principles and techniques are also applicable to extract fresh groundwater from coastal aquifers without the risk of saltwater incursion.

  20. A magnetometer for the cryogen-free systems: extraction and integration method

    International Nuclear Information System (INIS)

    Tripathi, T.S.; Tewari, G.C.; Rastogi, A.K.

    2008-01-01

    We have developed a highly versatile low cost magnetometer that can be attached to the popular cryogen-free helium refrigerator systems for low temperature and high magnetic field measurements. The method of slow extraction of magnetized specimen and precise integration of voltages induced in the pickup coil assembly gives the magnetization. The drawing details of the various parts like extraction unit, pickup coil assembly, high quality integrator circuit and timing circuit will be presented and we shall demonstrate a bench top unit at the conference site. (author)

  1. Extraction of self-diffusivity in systems with nondiffusive short-time behavior

    Science.gov (United States)

    Shanbhag, Sachin

    2013-10-01

    We consider a toy model that captures the short-time nondiffusive behavior seen in many physical systems, to study the extraction of self-diffusivity from particle trajectories. We propose and evaluate a simple method to automatically detect the transition to diffusive behavior. We simulate the toy model to generate data sets of varying quality and test different methods of extracting the self-diffusion coefficient and characterizing its uncertainty. We find that weighted least-squares with statistical bootstrap is the most accurate and efficient means for analyzing the trajectory data. The analysis suggests an iterative recipe for designing simulations to conform to a specified level of accuracy.

  2. Column Extraction and Separation of Some Metal Ions by Diethylenetriamine Polysiloxane Immobilized Ligand System

    OpenAIRE

    El-Ashgar, Nizam M.

    2008-01-01

    An extraction chromatographic solid porous polysiloxane functionalized by chelating diethylenetriamine ligand of the general formula P-(CH2)3-NH(CH2)2NH(CH2)2NH2, (Where P represents [Si-O]n siloxane network) has been evaluated for the separation of Co(II), Ni(II) and Cu(II) from aqueous solutions. The chromatographic parameters of the separation method have been optimized. The ligand system retained Co(II), Cu(II) and Zn(II) effectively when used as a metal ion extractant by controlling the...

  3. Use of Dimethyl Pimelimidate with Microfluidic System for Nucleic Acids Extraction without Electricity.

    Science.gov (United States)

    Jin, Choong Eun; Lee, Tae Yoon; Koo, Bonhan; Choi, Kyung-Chul; Chang, Suhwan; Park, Se Yoon; Kim, Ji Yeun; Kim, Sung-Han; Shin, Yong

    2017-07-18

    The isolation of nucleic acids in the lab on a chip is crucial to achieve the maximal effectiveness of point-of-care testing for detection in clinical applications. Here, we report on the use of a simple and versatile single-channel microfluidic platform that combines dimethyl pimelimidate (DMP) for nucleic acids (both RNA and DNA) extraction without electricity using a thin-film system. The system is based on the adaption of DMP into nonchaotropic-based nucleic acids and the capture of reagents into a low-cost thin-film platform for use as a microfluidic total analysis system, which can be utilized for sample processing in clinical diagnostics. Moreover, we assessed the use of the DMP system for the extraction of nucleic acids from various samples, including mammalian cells, bacterial cells, and viruses from human disease, and we also confirmed that the quality and quantity of the nucleic acids extracted were sufficient to allow for the robust detection of biomarkers and/or pathogens in downstream analysis. Furthermore, this DMP system does not require any instruments and electricity, and has improved time efficiency, portability, and affordability. Thus, we believe that the DMP system may change the paradigm of sample processing in clinical diagnostics.

  4. Piezoelectric ultrasonic bone surgery system in the extraction surgery of supernumerary teeth.

    Science.gov (United States)

    Gao, Yongbo; Lin, Zhenyan; Rodella, Luigi Fabrizio; Buffoli, Barbara; Wu, Xifeng; Zhou, Yanmin

    2014-12-01

    The anterior maxillary region is a common site for supernumerary teeth. The aim of this study was to compare the use of piezoelectric ultrasonic bone surgery for the extraction of supernumerary teeth and the use of traditional method using bone chisels. 60 patients with supernumerary anterior maxillary teeth were considered in this study. They were randomly divided into two groups: 1) the control group, in which the supernumerary teeth were extracted using the traditional bone chisels method; 2) the experimental group, in which the supernumerary teeth were extracted using a piezoelectric ultrasonic bone surgery system. The operative time, amount of bleeding and post-operative pain were quantified and compared; in addition, the post-operative swelling was evaluated. We observed a significant decrease (P supernumerary teeth was longer using the piezoelectric ultrasonic bone surgery system, the amount of bleeding and the post-operative complications were less, so this system could be considered an appropriate surgical method for the extraction of supernumerary teeth. Crown Copyright © 2014. Published by Elsevier Ltd. All rights reserved.

  5. Using decision-tree classifier systems to extract knowledge from databases

    Science.gov (United States)

    St.clair, D. C.; Sabharwal, C. L.; Hacke, Keith; Bond, W. E.

    1990-01-01

    One difficulty in applying artificial intelligence techniques to the solution of real world problems is that the development and maintenance of many AI systems, such as those used in diagnostics, require large amounts of human resources. At the same time, databases frequently exist which contain information about the process(es) of interest. Recently, efforts to reduce development and maintenance costs of AI systems have focused on using machine learning techniques to extract knowledge from existing databases. Research is described in the area of knowledge extraction using a class of machine learning techniques called decision-tree classifier systems. Results of this research suggest ways of performing knowledge extraction which may be applied in numerous situations. In addition, a measurement called the concept strength metric (CSM) is described which can be used to determine how well the resulting decision tree can differentiate between the concepts it has learned. The CSM can be used to determine whether or not additional knowledge needs to be extracted from the database. An experiment involving real world data is presented to illustrate the concepts described.

  6. Liquid-liquid extraction of uranium(VI) in the system with a membrane contactor.

    Science.gov (United States)

    Biełuszka, Paweł; Zakrzewska, Grażyna; Chajduk, Ewelina; Dudek, Jakub

    Raising role of the nuclear power industry, including governmental plans for the construction of first nuclear power plant in Poland, creates increasing demand for the uranium-based nuclear fuels. The project implemented by Institute of Nuclear Chemistry and Technology concerns the development of effective methods for uranium extraction from low-grade ores and phosphorites for production of yellow cake-U 3 O 8 . The Liqui-Cel ® Extra-Flow 2.5 × 8 Membrane Contactor produced by CELGARD LLC (Charlotte, NC) company is the main component of the installation for liquid-liquid extraction applied for processing of post leaching liquors. In the process of membrane extraction the uranyl ions from aqueous phase are transported through the membrane into organic phase. The flow of two phases in the system was arranged in co-current mode. The very important element of the work was a selection of extracting agents appropriate for the membrane process. After preliminary experiments comprising tests of membrane resistivity and determination of extraction efficiency, di(2-ethylhexyl)phosphoric acid was found to be most favourable. An important aspect of the work was the adjustment of hydrodynamic conditions in the capillary module. To avoid the membrane wettability by organic solvent and mixing two phases equal pressure drops along the membrane module to minimize the transmembrane pressure, were assumed. Determination of pressure drop along the module was conducted using Bernoulli equation. The integrated process of extraction/re-extraction conducted in continuous mode with application of two contactors was designed.

  7. Assessment of metal bioavailability in the vineyard soil-grapevine system using different extraction methods.

    Science.gov (United States)

    Vázquez Vázquez, Francisco A; Pérez Cid, Benita; Río Segade, Susana

    2016-10-01

    This study was focused on the assessment of single and sequential extraction methods to predict the bioavailability of metals in the vineyard soil-grapevine system. The modified BCR sequential extraction method and two single-step extraction methods based on the use of EDTA and acetic acid were applied to differently amended vineyard soils. The variety effect was studied on the uptake of metals by leaves and grapes. Most of the elements studied (Ca, Mg, Cu, Fe, Mn, Zn and Pb) were weakly mobilized from vineyard soils, with the exception of Cu and Mn. The determination of total metal content in leaves and grapes showed a different accumulation pattern in the two parts of the vine. A significant relationship was observed, for all the elements studied except for Fe, between the content bioavailable in the soil and the accumulated in both leaves and grapes (R=0.602-0.775, p<0.01). Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. The extraction system: Eu3+-water-NaCl-HDBM-Benzene

    International Nuclear Information System (INIS)

    Jimenez R, M.; Solache R, M.; Rojas H, A.

    1998-01-01

    It was studied the behavior as in acid as alkaline media of the extraction system with dissolvant integrated by trivalent europium in a 2a sodium chloride media and dibenzoylmethane (HDBM) in benzene at 303 K. It was established: the time in which the balance is reached, the influence of europium hydrolysis, the influence of atmospheric carbon dioxide, the influence of a competitive ligand such as diglycolic acid and the number of HDBM molecules that are consumed by each europium ion during extraction. The europium hydrolysis constants were determined by the potentiometric method, in presence or absence of carbonate ions and with those data distribution diagrams of the europium chemical species were obtained which were present in the aqueous phases of the extraction with dissolvant. (Author)

  9. MedTime: a temporal information extraction system for clinical narratives.

    Science.gov (United States)

    Lin, Yu-Kai; Chen, Hsinchun; Brown, Randall A

    2013-12-01

    Temporal information extraction from clinical narratives is of critical importance to many clinical applications. We participated in the EVENT/TIMEX3 track of the 2012 i2b2 clinical temporal relations challenge, and presented our temporal information extraction system, MedTime. MedTime comprises a cascade of rule-based and machine-learning pattern recognition procedures. It achieved a micro-averaged f-measure of 0.88 in both the recognitions of clinical events and temporal expressions. We proposed and evaluated three time normalization strategies to normalize relative time expressions in clinical texts. The accuracy was 0.68 in normalizing temporal expressions of dates, times, durations, and frequencies. This study demonstrates and evaluates the integration of rule-based and machine-learning-based approaches for high performance temporal information extraction from clinical narratives. Copyright © 2013 Elsevier Inc. All rights reserved.

  10. In vitro study on biomineralization of biphasic calcium phosphate ...

    Indian Academy of Sciences (India)

    hydrolysable tannins from Terminalia chebula (TC) extract as gelatin cross linking agent instead of glutaraldhyde to reduce the cytotoxicity (Julie et al 2002). Chemical con- stituents of TC extract are chebulagic acid, chebulinic acid, corilagin, beta-sitosterol, gallic acid, ellagic acid, ethyl gal- late, tannic acid, galloyl glucose ...

  11. Evaluation of the finite element software ABAQUS for biomechanical modelling of biphasic tissues.

    Science.gov (United States)

    Wu, J Z; Herzog, W; Epstein, M

    1998-02-01

    The biphasic cartilage model proposed by Mow et al. (1980) has proven successful to capture the essential mechanical features of articular cartilage. In order to analyse the joint contact mechanics in real, anatomical joints, the cartilage model needs to be implemented into a suitable finite element code to approximate the irregular surface geometries of such joints. However, systematic and extensive evaluation of the capacity of commercial software for modelling the contact mechanics with biphasic cartilage layers has not been made. This research was aimed at evaluating the commercial finite element software ABAQUS for analysing biphasic soft tissues. The solutions obtained using ABAQUS were compared with those obtained using other finite element models and analytical solutions for three numerical tests: an unconfined indentation test, a test with the contact of a spherical cartilage surface with a rigid plate, and an axi-symmetric joint contact test. It was concluded that the biphasic cartilage model can be implemented into the commercial finite element software ABAQUS to analyse practical joint contact problems with biphasic articular cartilage layers.

  12. Ultrasound-Assisted Aqueous Two-Phase System for Extraction and Enrichment of Zanthoxylum armatum Lignans

    Directory of Open Access Journals (Sweden)

    Tao Guo

    2015-08-01

    Full Text Available In the study, an aqueous two phase system (ATPS coupled with ultrasound was employed to extract lignans from Zanthoxylum armatum. Three standard lignans, namely (−-fargesin, sesamin and L-asarinin, were used as marker compounds, and extraction was optimized and projected by response surface methodology (RSM and artificial neural network (ANN. The optimal condition for ATPS with 20% n-propanol and 24% (NH42SO4 coupled with ultrasonic-assisted extraction including a solvent to solid ratio of 15:1, a temperature of 40 °C, and a treatment time of 55 min was obtained. Under the condition, the yield of (−-fargesin increased 15.12%, and the purities of (−-fargesin, sesamin and L-asarinin reached 2.222%, 1.066%, and 1.583%, with an increase of 44.38%, 25.70%, and 26.34% compared to those extracted with 95% ethanol, respectively. Coefficient of the determined (0.9855 and mean squared error (0.0018 of ANN model suggested good fitness and generalization of the ANN. Taken together, the results showed that ultrasonic-assisted ATPS can be a suitable method for extraction and enrichment of lignans from Z. armatum.

  13. Ultrasound-Assisted Aqueous Two-Phase System for Extraction and Enrichment of Zanthoxylum armatum Lignans.

    Science.gov (United States)

    Guo, Tao; Su, Dan; Huang, Yan; Wang, Ya; Li, Yong-Hui

    2015-08-20

    In the study, an aqueous two phase system (ATPS) coupled with ultrasound was employed to extract lignans from Zanthoxylum armatum. Three standard lignans, namely (-)-fargesin, sesamin and L-asarinin, were used as marker compounds, and extraction was optimized and projected by response surface methodology (RSM) and artificial neural network (ANN). The optimal condition for ATPS with 20% n-propanol and 24% (NH4)2SO4 coupled with ultrasonic-assisted extraction including a solvent to solid ratio of 15:1, a temperature of 40 °C, and a treatment time of 55 min was obtained. Under the condition, the yield of (-)-fargesin increased 15.12%, and the purities of (-)-fargesin, sesamin and L-asarinin reached 2.222%, 1.066%, and 1.583%, with an increase of 44.38%, 25.70%, and 26.34% compared to those extracted with 95% ethanol, respectively. Coefficient of the determined (0.9855) and mean squared error (0.0018) of ANN model suggested good fitness and generalization of the ANN. Taken together, the results showed that ultrasonic-assisted ATPS can be a suitable method for extraction and enrichment of lignans from Z. armatum.

  14. A flow reactor setup for photochemistry of biphasic gas/liquid reactions

    Directory of Open Access Journals (Sweden)

    Josef Schachtner

    2016-08-01

    Full Text Available A home-built microreactor system for light-mediated biphasic gas/liquid reactions was assembled from simple commercial components. This paper describes in full detail the nature and function of the required building elements, the assembly of parts, and the tuning and interdependencies of the most important reactor and reaction parameters. Unlike many commercial thin-film and microchannel reactors, the described set-up operates residence times of up to 30 min which cover the typical rates of many organic reactions. The tubular microreactor was successfully applied to the photooxygenation of hydrocarbons (Schenck ene reaction. Major emphasis was laid on the realization of a constant and highly reproducible gas/liquid slug flow and the effective illumination by an appropriate light source. The optimized set of conditions enabled the shortening of reaction times by more than 99% with equal chemoselectivities. The modular home-made flow reactor can serve as a prototype model for the continuous operation of various other reactions at light/liquid/gas interfaces in student, research, and industrial laboratories.

  15. Interfacial Tensions of Aged Organic Aerosol Particle Mimics Using a Biphasic Microfluidic Platform.

    Science.gov (United States)

    Metcalf, Andrew R; Boyer, Hallie C; Dutcher, Cari S

    2016-02-02

    Secondary organic aerosol (SOA) particles are a major component of atmospheric particulate matter, yet their formation processes and ambient properties are not well understood. These complex particles often contain multiple interfaces due to internal aqueous- and organic-phase partitioning. Aerosol interfaces can profoundly affect the fate of condensable organic compounds emitted into the atmosphere by altering the way in which ambient organic vapors interact with suspended particles. To accurately predict the evolution of SOA in the atmosphere, we must improve our understanding of aerosol interfaces. In this work, biphasic microscale flows are used to measure interfacial tension of reacting methylglyoxal, formaldehyde, and ammonium sulfate aqueous mixtures with a surrounding oil phase. Our experiments show a suppression of interfacial tension as a function of organic content that remains constant with reaction time for methylglyoxal-ammonium sulfate systems. We also reveal an unexpected time dependence of interfacial tension over a period of 48 h for ternary solutions of both methylglyoxal and formaldehyde in aqueous ammonium sulfate, indicating a more complicated behavior of surface activity where there is competition among dissolved organics. From these interfacial tension measurements, the morphology of aged atmospheric aerosols with internal liquid-liquid phase separation is inferred.

  16. Study of volume fractions on biphasic stratified regime using gamma ray

    Energy Technology Data Exchange (ETDEWEB)

    Salgado, William L.; Brandão, Luis E.B., E-mail: william.otero@hotmail.com, E-mail: brandao@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2017-07-01

    In the oil industries, interconnected pipelines are used to carry large quantities of petroleum and its byproducts. This modal has an advantage because they are more economical, eliminate a need for stocks and, in addition, great safety in operation minimizing a possibility of loss or theft when transported another way. In many cases, especially in the petrochemical industry, the same pipeline is used to carry more than one type of product. They are called poliduct. In the operation of a poliduct there is a sequence of products to be transported and during the exchange of the product, there are still fractions of the previous product and this generates contamination. It is therefore important to identify precisely this region in order to reduce the costs of reprocessing and treatment of discarded products. In this way, this work presents a methodology to evaluate the sensitivity of the gamma densitometry technique in a study of the calculation of volume fractions in biphasic systems, submitted to the stratified flow regime. Using computational simulations using the Monte Carlo Method with the MCNPX code measurement geometry was proposed that presented a higher sensitivity for the calculation of volume fractions. The relevant technical data to perform a simulation of the scintillator detectors were based on information obtained from the gammagraphy technique. The study had a theoretical validation through analytical equations, and the results show that it is possible to identify volume fractions equivalent to 3%. (author)

  17. A biphasic epigenetic switch controls immunoevasion, virulence and niche adaptation in non-typeable Haemophilus influenzae.

    Science.gov (United States)

    Atack, John M; Srikhanta, Yogitha N; Fox, Kate L; Jurcisek, Joseph A; Brockman, Kenneth L; Clark, Tyson A; Boitano, Matthew; Power, Peter M; Jen, Freda E-C; McEwan, Alastair G; Grimmond, Sean M; Smith, Arnold L; Barenkamp, Stephen J; Korlach, Jonas; Bakaletz, Lauren O; Jennings, Michael P

    2015-07-28

    Non-typeable Haemophilus influenzae contains an N(6)-adenine DNA-methyltransferase (ModA) that is subject to phase-variable expression (random ON/OFF switching). Five modA alleles, modA2, modA4, modA5, modA9 and modA10, account for over two-thirds of clinical otitis media isolates surveyed. Here, we use single molecule, real-time (SMRT) methylome analysis to identify the DNA-recognition motifs for all five of these modA alleles. Phase variation of these alleles regulates multiple proteins including vaccine candidates, and key virulence phenotypes such as antibiotic resistance (modA2, modA5, modA10), biofilm formation (modA2) and immunoevasion (modA4). Analyses of a modA2 strain in the chinchilla model of otitis media show a clear selection for ON switching of modA2 in the middle ear. Our results indicate that a biphasic epigenetic switch can control bacterial virulence, immunoevasion and niche adaptation in an animal model system.

  18. The Data Extraction Using Distributed Crawler Inside Multi-Agent System

    Directory of Open Access Journals (Sweden)

    Karel Tomala

    2013-01-01

    Full Text Available The paper discusses the use of web crawler technology. We created an application based on standard web crawler. Our application is determined for data extraction. Primarily, the application was designed to extract data using keywords from a social network Twitter. First, we created a standard crawler, which went through a predefined list of URLs and gradually download page content of each of the URLs. Page content was then parsed and important text and metadata were stored in a database. Recently, the application was modified in to the form of the multi-agent system. The system was developed in the C# language, which is used to create web applications and sites etc. Obtained data was evaluated graphically. The system was created within Indect project at the VSB-Technical University of Ostrava.

  19. Application of the code Slac to the study of Ion Extraction Systems in Neutral Injectors

    International Nuclear Information System (INIS)

    Garcia, M.; Liniers, M.; Guasp, J.

    1997-01-01

    In this study different extraction geometries for intense ion beams have been analyzed with the code SLAC, in view of its possible application to the neutral injectors of TJ-II. With this aim, we have introduced several modifications in the code in order to correctly simulate the transition between the ion source plasma and the extraction region, which has great impact on the beam optics. These modifications include the introduction of a population of Boltzmann electrons in the transition region, and the implementation of an option to simulate the thermal velocity of the ions in the source. We have found a better agreement between the results obtained with the new version of the code and the experimental data in two well known systems. With this new version of the code two different studies have been carried out: in the first place an optimization of the ATF injectors extraction system for its use on TJ-II, leading to an optimum value of the gap in the energy range 30-40 KeV, and in the second place a systematic study of extraction geometries at 40 KeV. As a result of this second study we have found the combinations of parameters that can be used under different working conditions (e.g. different pulse lengths), leading to acceptable values of the beam divergence. (Author)

  20. Evaluation of various solvent systems for lipid extraction from wet microalgal biomass and its effects on primary metabolites of lipid-extracted biomass.

    Science.gov (United States)

    Ansari, Faiz Ahmad; Gupta, Sanjay Kumar; Shriwastav, Amritanshu; Guldhe, Abhishek; Rawat, Ismail; Bux, Faizal

    2017-06-01

    Microalgae have tremendous potential to grow rapidly, synthesize, and accumulate lipids, proteins, and carbohydrates. The effects of solvent extraction of lipids on other metabolites such as proteins and carbohydrates in lipid-extracted algal (LEA) biomass are crucial aspects of algal biorefinery approach. An effective and economically feasible algae-based oil industry will depend on the selection of suitable solvent/s for lipid extraction, which has minimal effect on metabolites in lipid-extracted algae. In current study, six solvent systems were employed to extract lipids from dry and wet biomass of Scenedesmus obliquus. To explore the biorefinery concept, dichloromethane/methanol (2:1 v/v) was a suitable solvent for dry biomass; it gave 18.75% lipids (dry cell weight) in whole algal biomass, 32.79% proteins, and 24.73% carbohydrates in LEA biomass. In the case of wet biomass, in order to exploit all three metabolites, isopropanol/hexane (2:1 v/v) is an appropriate solvent system which gave 7.8% lipids (dry cell weight) in whole algal biomass, 20.97% proteins, and 22.87% carbohydrates in LEA biomass. Graphical abstract: Lipid extraction from wet microalgal biomass and biorefianry approach.

  1. Stepwise elution of a three-phase solvent system in centrifugal partition extraction: a new strategy for the fractionation and phytochemical screening of a crude bark extract.

    Science.gov (United States)

    Hamzaoui, Mahmoud; Renault, Jean-Hugues; Nuzillard, Jean-Marc; Reynaud, Romain; Hubert, Jane

    2013-01-01

    Tree bark represents an interesting source of bioactive molecules for the discovery of new pharmaceutical agents. However, the detailed screening of secondary metabolites in crude bark extracts is often hampered by the presence of tannins, which are difficult to separate from other plant constituents. In the present study, a new centrifugal partition extraction (CPE) method was developed in order to fractionate a crude bark extract of Anogeissus leiocarpus Guill. & Perr. (Combretaceae). A three-phase solvent system composed of n-heptane, methyl tert-butyl ether, acetonitrile and water was optimised for the stepwise elution at 20 mL/min of different phytochemical classes according to their hydrophobicity. Onedimensional and two-dimensional NMR analyses of the simplified fractions were then performed in order to characterise potentially interesting metabolites. In one step, 5 g of the initial crude extract were efficiently fractionated to yield highly simplified fractions that contained triterpenes, ellagic acid derivatives, flavonoids and phenolic compounds. All undesired compounds, that is, the highly abundant water-soluble tannins (78.8%), were totally removed and each run was rapidly achieved in 90 min on a the multi-gram scale and with low solvent volumes. Centrifugal partition extraction in the elution mode using a three-phase solvent system can thus be proposed as an efficient and cost-effective alternative for a rapid fractionation of crude bark extracts and for an effective screening of potentially active secondary metabolites. Copyright © 2013 John Wiley & Sons, Ltd.

  2. Biphasic Synergistic Gel Materials with Switchable Mechanics and Self-Healing Capacity.

    Science.gov (United States)

    Zhao, Ziguang; Liu, Yuxia; Zhang, Kangjun; Zhuo, Shuyun; Fang, Ruochen; Zhang, Jianqi; Jiang, Lei; Liu, Mingjie

    2017-10-16

    A fabrication strategy for biphasic gels is reported, which incorporates high-internal-phase emulsions. Closely packed micro-inclusions within the elastic hydrogel matrix greatly improve the mechanical properties of the materials. The materials exhibit excellent switchable mechanics and shape-memory performance because of the switchable micro- inclusions that are incorporated into the hydrogel matrix. The produced materials demonstrated a self-healing capacity that originates from the noncovalent effect of the biphasic heteronetwork. The aforementioned characteristics suggest that the biphasic gels may serve as ideal composite gel materials with validity in a variety of applications, such as soft actuators, flexible devices, and biological materials. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. The Septum Magnet System of the New Fast Extraction Channel of the SPS at CERN

    CERN Document Server

    Balhan, B; Rizzo, A; Weterings, W

    2004-01-01

    In the Long Straight Section LSS4 of the Super Proton Synchrotron (SPS) at CERN, a new fast extraction system has been installed in order to extract the beam to ring 2 of the Large Hadron Collider (LHC) and the CERN Neutrino to Gran Sasso facility (CNGS). The system consists of horizontal closed orbit bumper magnets, extraction kicker magnets, enlarged aperture quadrupoles and six conventional DC electromagnetic septum magnets (MSE). A protection element (TPSG) has been placed immediately upstream of the first septum coil. The septum magnets and TPSG are mounted on a single mobile retractable support girder. The MSE septa are connected by a so-called plug-in system to a rigid water-cooled bus-bar, powered by water-cooled cables. The whole system is kept at the required vacuum pressure by ion pumps attached to separate pumping modules. In this note we present the design features and parameters of the MSE septum magnets, describe the function of the related main equipment elements, briefly report on the control...

  4. In Vitro effect of some medicinal plant extracts on stimulating theimmune system in cancer patients

    International Nuclear Information System (INIS)

    Shawar, Said M.; Al-Aqtum, Musa T.; Al-Kayed, Sameer A.

    2008-01-01

    The difficulty to treat cancer without side effects by surgery,chemotherapy, radiotherapy and immunotherapy, has led investigators to lookfor phytotherapy as a new strategy in cancer medicine. The immune systemplays an important role in anti-tumor defenses, thus, we evaluated theproliferation potential of aqueous extracts from five medicinal plants onperipheral blood lymphocytes (PBLs) from 118 properly consented volunteers.We examined the aqueous extract of Thyme, Sage, Clove, Calament and BlackSeed in vitro on PBLs from 100 cancer patients seeking treatment atAl-Basheer Hospital in Amman and 18 apparently healthy volunteers. PBLs wereisolated from blood samples collected in heparin tubes. Then,Ficoll-Hypaquedensity gradient configuration was employed to enrich forlymphocytes. Cells were collected in RPMI containing 10% human serum at106/mL before culturing them at an appropriate density. Three concentrationsof the aqueous extract from each plant were assayed in duplicates on culturedPBLs for 72 hours. Cell proliferation was quantified using 3-(4,5-Dimethylthiazol-2yl)-2, 5-diphenyltetrazolium bromide (MTT) standardmethod. Phytohemagglutinin (PHA) was used as a positive proliferation controland sterile RPMI medium was used as a negative control. Among the fivedifferent aqueous extracts used in this study, only sage aqueous extractdemonstrated promising results. Sage extract was effective in proliferatingPBLs of all normal controls and cancer patients tested. Proliferation of themajority of PBLs from cancer patients was highly effective. However, somesamples showed a weaker index of proliferation. PBLs proliferation exhibiteda dose-dependent effect. The effectiveness among cancer patients was age,sex, cancer-type and cancer-stage independent. Our data suggest that theaqueous extract of sage contains a polyclonal mitogen(s) that enhances theimmune system in a non-specific fashion. (author)

  5. A Structurally and Functionally Biomimetic Biphasic Scaffold for Intervertebral Disc Tissue Engineering

    Science.gov (United States)

    Choy, Andrew Tsz Hang; Chan, Barbara Pui

    2015-01-01

    Tissue engineering offers high hopes for the treatment of intervertebral disc (IVD) degeneration. Whereas scaffolds of the disc nucleus and annulus have been extensively studied, a truly biomimetic and mechanically functional biphasic scaffold using naturally occurring extracellular matrix is yet to be developed. Here, a biphasic scaffold was fabricated with collagen and glycosaminoglycans (GAGs), two of the most abundant extracellular matrix components in the IVD. Following fabrication, the scaffold was characterized and benchmarked against native disc. The biphasic scaffold was composed of a collagen-GAG co-precipitate making up the nucleus pulposus-like core, and this was encapsulated in multiple lamellae of photochemically crosslinked collagen membranes comprising the annulus fibrosus-like lamellae. On mechanical testing, the height of our engineered disc recovered by ~82-89% in an annulus-independent manner, when compared with the 99% recovery exhibited by native disc. The annulus-independent nature of disc height recovery suggests that the fluid replacement function of the engineered nucleus pulposus core might mimic this hitherto unique feature of native disc. Biphasic scaffolds comprised of 10 annulus fibrosus-like lamellae had the best overall mechanical performance among the various designs owing to their similarity to native disc in most aspects, including elastic compliance during creep and recovery, and viscous compliance during recovery. However, the dynamic mechanical performance (including dynamic stiffness and damping factor) of all the biphasic scaffolds was similar to that of the native discs. This study contributes to the rationalized design and development of a biomimetic and mechanically viable biphasic scaffold for IVD tissue engineering. PMID:26115332

  6. Antioxidant Effect of Seaweed Extracts in Vitro and in Food Emulsion Systems Enriched With Fish Oil

    DEFF Research Database (Denmark)

    Larsen, Ditte Baun; Farvin, Sabeena; Jacobsen, Charlotte

    ongoing work on the brown algae Fucus vesiculosus. This seaweed contains a wide range of polyphenols with potential antioxidant activity. Thus, in vitro antioxidant properties of F. vesiculosus extracts have been found to be related to the total polyphenolic content. It has been suggested that the primary...... antioxidant activity comes from secondary metabolites such as phlorotannins, a dominant polyphenolic compound. However, studies on the effectiveness of seaweed extracts in food model systems are sparse, therefore there is a need to look further into this area. Results obtained in our lab with different......Natural antioxidants derived from marine algae have a high content of bioactive components with potential for improving oxidative stability of lipids in food systems. Bioactive components like polyphenols have been identified in marine algae. In this presentation we will discuss results from our...

  7. The extraction of uranyl nitrate and chloride in octaethyltetraamidopyrophosphate (OETAPP)-HCl, HNO3 systems

    International Nuclear Information System (INIS)

    Jankowska, M.; Kulawik, J.; Mikulski, J.

    1975-01-01

    The extraction of uranium was studied in the system of 0.1 M OETAPP in CHCl 3 /HCl or HNO 3 . The distribution coefficients of HCl and HNO 3 were calculated as a function of OETAPP concentration. The amount of OETAPP in the aqueous phase containing HCl and HNO 3 was found from the measurements of surface tension of this phase. The distribution of HCl or HNO 3 between the organic and aqueous phases was studied as a function of the concentration of the acid used in the aqueous phase. The solvation energy of the extracted complexes was calculated from the measured potential differences. Cohesion and adhesion energies of the studied systems are also given. (author)

  8. Electrokinetic electrode system for extraction of soil contaminants from unsaturated soils

    Science.gov (United States)

    Lindgren, Eric R.; Mattson, Earl D.

    1995-01-01

    There is presented an electrokinetic electrode assembly for use in extraction of soil contaminants from unsaturated soil in situ. The assembly includes a housing for retaining a liquid comprising an electrolyte solution, pure water, and soil water, the housing being in part of porous material capable of holding a vacuum. An electrode is mounted in the housing. The housing is provided with a vacuum orifice for effecting a vacuum within the housing selectively to control flow of soil water through the housing into the chamber and to control outflow of the liquid from the chamber. The assembly further includes conduit means for removing the liquid from the housing and returning the electrolyte solution to the housing, and a conduit for admitting pure water to the housing. There is further presented an electrode system and method for extraction of soil contaminants, the system and method utilizing at least two electrode assemblies as described above.

  9. Radiator Enhanced Geothermal System - A Revolutionary Method for Extracting Geothermal Energy

    Science.gov (United States)

    Karimi, S.; Marsh, B. D.; Hilpert, M.

    2017-12-01

    A new method of extracting geothermal energy, the Radiator Enhanced Geothermal System (RAD-EGS) has been developed. RAD-EGS attempts to mimic natural hydrothermal systems by 1) generating a vertical vane of artificially produced high porosity/permeability material deep in a hot sedimentary aquifer, 2) injecting water at surface temperatures to the bottom of the vane, where the rock is the hottest, 3) extracting super-heated water at the top of the vane. The novel RAD-EGS differs greatly from the currently available Enhanced Geothermal Systems in vane orientation, determined in the governing local crustal stress field by Shmax and Sl (meaning it is vertical), and in the vane location in a hot sedimentary aquifer, which naturally increases the longevity of the system. In this study, we explore several parameters regimes affecting the water temperature in the extraction well, keeping in mind that the minimum temperature of the extracted water has to be 150 °C in order for a geothermal system to be commercially viable. We used the COMSOL finite element package to simulate coupled heat and fluid transfer within the RAD-EGS model. The following geologic layers from top to bottom are accounted for in the model: i) confining upper layer, ii) hot sedimentary aquifer, and iii) underlying basement rock. The vane is placed vertically within the sedimentary aquifer. An injection well and an extraction well are also included in the simulation. We tested the model for a wide range of various parameters including background heat flux, thickness of geologic layers, geometric properties of the vane, diameter and location of the wells, fluid flow within the wells, regional hydraulic gradient, and permeability and porosity of the layers. The results show that among the aforementioned parameters, background heat flux and the depth of vane emplacement are highly significant in determining the level of commercial viability of the geothermal system. These results indicate that for the

  10. Getting Objects Methods and Interactions by Extracting Business Rules from Legacy Systems

    Directory of Open Access Journals (Sweden)

    Omar El Beggar

    2014-08-01

    Full Text Available The maintenance of legacy systems becomes over the years extremely complex and highly expensive due to the incessant changes of company activities and policies. In this case, a new or an improved system must replace the previous one. However, replacing those systems completely from scratch is also very expensive and it represents a huge risk. The optimal scenario is evolving those systems by profiting from the valuable knowledge embedded in them. This paper aims to present an approach for knowledge acquisition from existing legacy systems by extracting business rules from source code. In fact, the business rules are extracted and assigned next to the domain entities in order to generate objects methods and interactions in an object-oriented platform. Furthermore, a rules translation in natural language is given. The aim is advancing a solution for re-engineering legacy systems, minimize the cost of their modernization and keep very small the gap between the company business and the renovated systems.

  11. Evaluation of solvent systems for optimized extractables studies of single use bioprocessing solutions.

    Science.gov (United States)

    Dorival-García, Noemí; Bones, Jonathan

    2017-09-01

    Despite their advantages, there is concern that single-use systems used in biopharmaceutical manufacture might release potentially toxic substances during standard unit operations that negatively impact cell growth. Characterization of the extractables profile for single-use systems is necessary to know which compounds potentially become leachables under operational cell culture conditions. A key issue in the design of extractables studies is the composition of the model solvent, in particular its pH and polarity. In this study, a new approach, based on design of experiments (DoE), has been applied to determine the composition of the model solvent for extractable profiling of single-use bags (SUBs). Particular focus was placed on the determination of the degradation products of the antioxidant Irgafos 168 ® , due to evidence that some of these degradation products have cytotoxic effects on CHO cells. Results indicated that 2-propanol:water is the most appropriate solvent for the extraction of highly hydrophobic compounds with polar groups and/or acid-base properties from SUBs. The described DoE approach simplifies the number of experiments, evaluates all possible solvent water mixtures to select the best extraction solvent based on polarity, establishes the influence of each variable and provides information about variable interaction, which represents an important improvement over current best practice. The developed approach was applied to seven SUBs from different vendors and production dates facilitating the identification of potentially non-satisfactory films for cultivation of CHO cell lines under process conditions. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Integrated silicon grid ion extraction system for O sub 2 processes

    Energy Technology Data Exchange (ETDEWEB)

    Korzec, D.; Engemann, J.; Bansky, J.; Keller, H.M. (University of Wuppertal, Department of Electrical Engineering, 5600 Wuppertal 1, West Germany (DE))

    1990-11-01

    A novel multibeamlet very low energy ion extraction optic technology avoiding cumbersome grid readjustment and thermal degradation of beam properties during a reactive process has been developed. In this approach anisotropically etched silicon grids ((100)-oriented Si wafers) are permanently integrated into a holder made of layered ceramics or micromachined AlN. The performance of such extraction systems having 300, 600, and 900 {mu}m grid separation was tested in a 3 cm capacitively coupled rf-ion source. Stable system operation with use of oxygen has been achieved for an extended period of time ({gt}100 h) for a total extraction voltage of 140 V which represents the maximum voltage to be applied for a grid separation of 0.3 mm. Additionally detailed Faraday-cup measurements of the extracted ion beam have been carried out for a total voltage range of 0--600 V, a vacuum chamber pressure of 1{times}10{sup {minus}4}--1{times}10{sup {minus}3} mbar, rf-power levels of 10--170 W, a net-to-total voltage ratio of 0.5--1.0 and an axial magnetic field of up to 22 mT. For O{sub 2} an ion current density of 1.3 mA/cm{sup 2} could be extracted with ions having a mean energy of 60 eV. Even for energies as low as 50-eV current densities of 0.8 mA/cm{sup 2} could be achieved. In combination with the filamentless capacitively coupled rf source used, this approach has promise in various fields of materials research and processing such as ion beam assisted deposition of high-{ital T}{sub {ital c}} YBaCuO layers and etching/modification of diamondlike, diamond and polymer thin films.

  13. The standard biphasic-contrast examination of the stomach and duodenum

    International Nuclear Information System (INIS)

    Op den Orth, J.O.

    1979-01-01

    A standard examination has been developed, called biphasic, because it combines the advantages of positive-contrast and double-contrast techniques. The theoretical background and technique of this examination are described and the basic interpretation of double-contrast studies stated. General remarks on the results and on the complementary role of radiological examination and endoscopy are included. A quantitative study of standard biphasic-contrast examinations in patients over a period of 3 years is presented. Finally a radiological atlas of common lesions of the stomach and duodenum is given. (C.F.)

  14. Paired associative stimulation targeting the tibialis anterior muscle using either mono or biphasic transcranial magnetic stimulation

    DEFF Research Database (Denmark)

    Mrachacz-Kersting, Natalie; Stevenson, Andrew James Thomas

    2017-01-01

    Paired associative stimulation (PAS) protocols induce plastic changes within the motor cortex. The objectives of this study were to investigate PAS effects targeting the tibialis anterior (TA) muscle using a biphasic transcranial magnetic stimulation (TMS) pulse form and, to determine whether...... a reduced intensity of this pulse would lead to significant changes as has been reported for hand muscles using a monophasic TMS pulse. Three interventions were investigated: (1) suprathreshold PAbi-PAS (n = 11); (2) suprathreshold PAmono-PAS (n = 11) where PAS was applied using a biphasic or monophasic...

  15. Master data extraction and adaptation based on collected production data in manufacturing execution systems

    OpenAIRE

    Dimitrov, T.; Baumann, M.; Schenk, M.

    2010-01-01

    This paper presents an approach to extraction and correction of manufacturing master data, needed by Manufacturing Execution Systems (MES) to control and schedule the production. The implementation of the created schedule and the improvement of Key Performance Indicators depends strongly on the quality of the master data. The master data of most enterprises ages or the enterprises cannot fully provide it, because a highly manual expense for statistical analysis and administration is needed. T...

  16. Mixing in three-phase systems: Implications for enhanced oil recovery and unconventional gas extraction

    Science.gov (United States)

    Jimenez-Martinez, J.; Porter, M. L.; Hyman, J.; Carey, J. W.; Viswanathan, H. S.

    2015-12-01

    Although the mixing of fluids within a porous media is a common process in natural and industrial systems, how the degree of mixing depends on the miscibility of multiple phases is poorly characterized. Often, the direct consequence of miscible mixing is the modification of the resident fluid (brine and hydrocarbons) rheological properties. We investigate supercritical (sc)CO2 displacement and mixing processes in a three-phase system (scCO2, oil, and H2O) using a microfluidics experimental system that accommodates the high pressures and temperatures encountered in fossil fuel extraction operations. The miscibility of scCO2 with the resident fluids, low with aqueous solutions and high with hydrocarbons, impacts the mixing processes that control sweep efficiency in enhanced oil recovery (EOR) and the unlocking of the system in unconventional oil and gas extraction. Using standard volume-averaging techniques we upscale the aqueous phase saturation to the field-scale (i.e., Darcy scale) and interpret the results as a simpler two-phase system. This process allows us to perform a statistical analysis to quantify i) the degree of heterogeneity in the system resulting from the immiscible H2O and ii) how that heterogeneity impacts mixing between scCO2 and oil and their displacement. Our results show that when scCO2 is used for miscible displacement, the presence of an aqueous solution, which is common in secondary and tertiary EOR and unconventional oil and gas extraction, strongly impacts the mixing of scCO2 with the hydrocarbons due to low scCO2-H2O miscibility. H2O, which must be displaced advectively by the injected scCO2, introduces spatio-temporal variability into the system that acts as a barrier between the two miscibile fluids. This coupled with the effect of viscosity contrast, i.e., viscous fingering, has an impact on the mixing of the more miscible pair.

  17. Ficaria verna Huds. extracts and their β-cyclodextrin supramolecular systems

    Directory of Open Access Journals (Sweden)

    Hădărugă Nicoleta G

    2012-03-01

    Full Text Available Abstract Background Obtaining new pharmaceutical materials with enhanced properties by using natural compounds and environment-friendly methods is a continuous goal for scientists. Ficaria verna Huds. is a widespread perennial plant with applications in the treat of haemorrhoids and to cure piles; it has also anti-inflammatory, astringent, and antibiotic properties. The goal of the present study is the obtaining and characterization of new F. verna extract/β-cyclodextrin complexes by using only natural compounds, solvents, and environment-friendly methods in order to increase the quality and acceptability versus toxicity indicator. Thus, the flavonoid content (as quercetin of Ficaria verna Huds. flowers and leaves from the West side of Romania was determined and correlated with their antioxidant activity. Further, the possibility of obtaining β-cyclodextrin supramolecular systems was studied. Results F. verna flowers and leaves extracts were obtained by semi-continuous solid-liquid extraction. The raw concentrated extract was spectrophotometrically analyzed in order to quantify the flavonoids from plant parts and to evaluate the antioxidant activity of these extracts. The F. verna extracts were used for obtaining β-cyclodextrin complexes; these were analyzed by scanning electron microscopy and Karl Fischer water titration; spectrophotometry was used in order to quantifying the flavonoids and evaluates the antioxidant activity. A higher concentration of flavonoids of 0.5% was determined in complexes obtained by crystallisation method, while only a half of this value was calculated for kneading method. The antioxidant activity of these complexes was correlated with the flavonoid content and this parameter reveals possible controlled release properties. Conclusions The flavonoid content of F. verna Huds. from the West side of Romania (Banat county is approximately the same in flowers and leaves, being situated at a medium value among other

  18. Laboratory studies of the behavior of undissolved solids in both pulsed and packed column extraction systems

    International Nuclear Information System (INIS)

    Siemer, D.D.

    1989-01-01

    A substantial fraction of the finely divided undissolved solid material found in nuclear fuel reprocessing dissolver-product solutions is hydrophobic and tends to ''seek'' any organic-aqueous interface existing within countercurrent liquid-liquid extraction systems. While passing through pulsed-type columns this material is swept out of the aqueous phase by the combined surface area of the tiny bubbles of dispersed phase. Because these bubbles have a net velocity towards the end of the column where the nominal interface is located, the solids are swept in that direction too. These solids tend to gather in a three-phase ''crud'' layer at the nominal interface point. At equilibrium, about the same amount breaks off from the crud layer and escapes into the liquid exiting from that end of the column as enters it from the other side. If large enough, the crud layer can even interfere with interface detection and control equipment. In packed-column extraction systems, an additional problem is that feed solids can accumulate within the packing material to the point that the column '' floods'' or even totally plugs. The keys to preventing solids-related problems is the correct choice of interface level, and with packed columns, the addition of a ''pulsing leg'' at the bottom of the column. Pulsing packed column systems not only prevents solids from settling onto packing material but it also increses the number of theoretical stages available for extraction. 3 figs., 2 tabs

  19. Radiation-chemical transformations of extraction system components in the presence of palladium

    International Nuclear Information System (INIS)

    Zajtsev, V.D.; Egorov, G.F.

    1988-01-01

    The effect of palladium concentrations in aqueous phase on radiation-chemical destruction of components of two-phase extraction system, containing organic 30% TBP solution in dodecane and aqueous solution of 1.31 mol/l uranyl nitrate in 3 mol/l nitric acid, is studied. The change in palladium extraction behaviour, depending on the dose of 60 Co gamma-radiation at the dose rate of 7 Gy/s absorbed by the system, is investigated. It is shown that palladium presence increases considerably the stationary concentration of nitric acid in irradiated aqueous solution, which results in the increase of organic nitrates yield in case of two-phase system irradiation. Palladium presence neither changes the yields of nitrocompounds and carboxyl-containing oxidation products of diluent, nor the yields of TBP radiation decomposition acid product formation. It is shown that noticeable increase in palladium distribution coefficients is observed already at th doses above 72 kGy. Extracted palladium is removed from the organic phase, irradiated by the dose exceeding 100 kGy, with great difficulty

  20. Work extraction in an isolated quantum lattice system: Grand canonical and generalized Gibbs ensemble predictions.

    Science.gov (United States)

    Modak, Ranjan; Rigol, Marcos

    2017-06-01

    We study work extraction (defined as the difference between the initial and the final energy) in noninteracting and (effectively) weakly interacting isolated fermionic quantum lattice systems in one dimension, which undergo a sequence of quenches and equilibration. The systems are divided in two parts, which we identify as the subsystem of interest and the bath. We extract work by quenching the on-site potentials in the subsystem, letting the entire system equilibrate, and returning to the initial parameters in the subsystem using a quasistatic process (the bath is never acted upon). We select initial states that are direct products of thermal states of the subsystem and the bath, and consider equilibration to the generalized Gibbs ensemble (GGE, noninteracting case) and to the Gibbs ensemble (GE, weakly interacting case). We identify the class of quenches that, in the thermodynamic limit, results in GE and GGE entropies after the quench that are identical to the one in the initial state (quenches that do not produce entropy). Those quenches guarantee maximal work extraction when thermalization occurs. We show that the same remains true in the presence of integrable dynamics that results in equilibration to the GGE.

  1. Using Auditory Cues to Perceptually Extract Visual Data in Collaborative, Immersive Big-Data Display Systems

    Science.gov (United States)

    Lee, Wendy

    The advent of multisensory display systems, such as virtual and augmented reality, has fostered a new relationship between humans and space. Not only can these systems mimic real-world environments, they have the ability to create a new space typology made solely of data. In these spaces, two-dimensional information is displayed in three dimensions, requiring human senses to be used to understand virtual, attention-based elements. Studies in the field of big data have predominately focused on visual representations and extractions of information with little focus on sounds. The goal of this research is to evaluate the most efficient methods of perceptually extracting visual data using auditory stimuli in immersive environments. Using Rensselaer's CRAIVE-Lab, a virtual reality space with 360-degree panorama visuals and an array of 128 loudspeakers, participants were asked questions based on complex visual displays using a variety of auditory cues ranging from sine tones to camera shutter sounds. Analysis of the speed and accuracy of participant responses revealed that auditory cues that were more favorable for localization and were positively perceived were best for data extraction and could help create more user-friendly systems in the future.

  2. Biphasic poly-dispersions modelling with applications in nuclear safety

    International Nuclear Information System (INIS)

    Gimenez, Marcelo

    2005-01-01

    Many technological, scientific and environmental areas require of the understanding of multiple-phase, polydisperse systems.Particularly, in nuclear safety area, under hypothetical severe accident conditions, the fission products are released as gases and airborne particles.In the present thesis a contribution to the modeling of confined polydisperse systems (aerosols and liquid-gas) is presented. A family of one and two dimensional models was developed, describing the impact of the particles size on the aerosol evolution, taking into account the transport mechanisms by the carrying media, settling, lift, thermophoresis, diffusion, coagulation and condensation, considering the spatial dependence. The aerosol general dynamic balance equation -no-linear integral-differential equation-, is treated by means of the Moments Method, imposing a prescribed volume size distribution, and obtaining a model based in the first few moments.This yields to a relatively simple convection-diffusion set of coupled equations, that describes the evolution of the parameters that characterize the size distribution, with a low computational cost that allows to deal the heterogeneities of the spatial distribution of the aerosol.A complementary model, based also on the Moments Method, is developed to perform sensitivity analysis due to uncertainties in the constitutive equations and in the input parameters.The Perturbative Method, Differential-formalism, is used to develop a set of sensitivity equations, which are useful for designing experiments and theoretical studies.The model results are compared with exact solutions and numerical and experimental data extracted from the open literature.Various physical phenomena involved in different simulated case are analysed in detail.Particularly, the study is oriented to the analysis of the concentration gradients and the validation of the aerosol well-mixed hypothesis, typically used in present numerical codes.Deviations were observed from the

  3. Biphasic defibrillation using a single capacitor with large capacitance: reduction of peak voltages and ICD device size.

    Science.gov (United States)

    Block, M; Hammel, D; Böcker, D; Borggrefe, M; Budde, T; Isbruch, F; Scheld, H H; Breithardt, G

    1996-02-01

    The volume of current implantable cardioverter defibrillators (ICD) is not convenient for pectoral implantation. One way to reduce the size of the pulse generator is to find a more effective defibrillation pulse waveform generated from smaller volume capacitors. In a prospective randomized crossover study we compared the step-down defibrillation threshold (DFT) of a standard biphasic waveform (STD), delivered by two 250-microF capacitors connected in series with an 80% tilt, to an experimental biphasic waveform delivered by a single 450-microF capacitor with a 60% tilt. The experimental waveform delivered the same energy with a lower peak voltage and a longer duration (LVLD). Intraoperatively, in 25 patients receiving endocardial (n = 12) or endocardial-subcutaneous array (n = 13) defibrillation leads, the DFT was determined for both waveforms. Energy requirements did not differ at DFT for the STD and LVLD waveforms with the low impedance (32 +/- 4 omega) endocardial-subcutaneous array defibrillation lead system (6.4 +/- 4.4 J and 5.9 +/- 4.2 J, respectively) or increased slightly (P = 0.06) with the higher impedance (42 +/- 4 omega) endocardial lead system (10.4 +/- 4.6 J and 12.7 +/- 5.7 J, respectively). However, the voltage needed at DFT was one-third lower with the LVLD waveform than with the STD waveform for both lead systems (256 +/- 85 V vs 154 +/- 51 V and 348 +/- 76 V vs 232 +/- 54 V, respectively). Thus, a single capacitor with a large capacitance can generate a defibrillation pulse with a substantial lower peak voltage requirement without significantly increasing the energy requirements. The volume reduction in using a single capacitor can decrease ICD device size.

  4. Extraction of fetal electrocardiogram using adaptive neuro-fuzzy inference systems.

    Science.gov (United States)

    Assaleh, Khaled

    2007-01-01

    In this paper, we investigate the use of adaptive neuro-fuzzy inference systems (ANFIS) for fetal electrocardiogram (FECG) extraction from two ECG signals recorded at the thoracic and abdominal areas of the mother's skin. The thoracic ECG is assumed to be almost completely maternal (MECG) while the abdominal ECG is considered to be composite as it contains both the mother's and the fetus' ECG signals. The maternal component in the abdominal ECG signal is a nonlinearly transformed version of the MECG. We use an ANFIS network to identify this nonlinear relationship, and to align the MECG signal with the maternal component in the abdominal ECG signal. Thus, we extract the FECG component by subtracting the aligned version of the MECG signal from the abdominal ECG signal. We validate our technique on both real and synthetic ECG signals. Our results demonstrate the effectiveness of the proposed technique in extracting the FECG component from abdominal signals of very low maternal to fetal signal-to-noise ratios. The results also show that the technique is capable of extracting the FECG even when it is totally embedded within the maternal QRS complex.

  5. EXTRACT OF Punica granatum L.: AN ALTERNATIVE TO BHT AS AN ANTIOXIDANT IN SEMISSOLID EMULSIFIED SYSTEMS

    Directory of Open Access Journals (Sweden)

    Jéssica Tiago Tozetto

    Full Text Available Pomegranate (Punica granatum L. is a fruit which has important pharmacological activities and has been attracting attention due to its important antioxidant activity, a significant feature in relation to cosmetics. Formulations containing different concentrations of an ethanolic extract of pomegranate (0.1, 1.0 and 5.0% (w/w as an antioxidant agent showed that this is an interesting alternative for the use of natural products with biological activity. The stability and rheology of semissolid systems containing an extract of this plant were evaluated. Preliminary stability studies showed greater physico-chemical stability of the formulation, and thus it was used in an accelerated stability study, as well the quantification of total phenolic compounds and the determination of antioxidant activity. It was observed that different concentrations of the extract did not significantly influence the stability. Moreover, the formulation was found to have better stability when stored at room temperature than under heated or cooled conditions. Formulations containing 0.1 and 5.0% of extract showed more stable rheological behavior, due to the absence of a solid/liquid transition in the rheogram. Tests confirmed the high phenolic content and antioxidant activity, demonstrating the potential of this plant for use in cosmetology as an antioxidant.

  6. Vaccine adverse event text mining system for extracting features from vaccine safety reports.

    Science.gov (United States)

    Botsis, Taxiarchis; Buttolph, Thomas; Nguyen, Michael D; Winiecki, Scott; Woo, Emily Jane; Ball, Robert

    2012-01-01

    To develop and evaluate a text mining system for extracting key clinical features from vaccine adverse event reporting system (VAERS) narratives to aid in the automated review of adverse event reports. Based upon clinical significance to VAERS reviewing physicians, we defined the primary (diagnosis and cause of death) and secondary features (eg, symptoms) for extraction. We built a novel vaccine adverse event text mining (VaeTM) system based on a semantic text mining strategy. The performance of VaeTM was evaluated using a total of 300 VAERS reports in three sequential evaluations of 100 reports each. Moreover, we evaluated the VaeTM contribution to case classification; an information retrieval-based approach was used for the identification of anaphylaxis cases in a set of reports and was compared with two other methods: a dedicated text classifier and an online tool. The performance metrics of VaeTM were text mining metrics: recall, precision and F-measure. We also conducted a qualitative difference analysis and calculated sensitivity and specificity for classification of anaphylaxis cases based on the above three approaches. VaeTM performed best in extracting diagnosis, second level diagnosis, drug, vaccine, and lot number features (lenient F-measure in the third evaluation: 0.897, 0.817, 0.858, 0.874, and 0.914, respectively). In terms of case classification, high sensitivity was achieved (83.1%); this was equal and better compared to the text classifier (83.1%) and the online tool (40.7%), respectively. Our VaeTM implementation of a semantic text mining strategy shows promise in providing accurate and efficient extraction of key features from VAERS narratives.

  7. Antioxidant activity and sensory analysis of murtilla (Ugni molinae Turcz.) fruit extracts in an oil model system

    International Nuclear Information System (INIS)

    Augusto-Obara, T.R.; Pirce, F.; Scheuermann, E.; Spoto, M.H.F.; Vieira, T.M.F.S.

    2017-01-01

    An oil model system was used to analyze the antioxidant activity of Chilean fruit extracts and to determine their odor sensory effect. Hydroalcoholic extracts from wild and 14-4 genotype murtilla (Ugni molinae Turcz.) fruit were assessed by the Response Surface Methodology. The optimal conditions for producing high total phenolic-content extracts were 49.5% (v/v) ethanol at 30 ºC, which yielded 18.39 and 26.14 mg GAE·g−1 dry matter, respectively. The optimized extracts were added to a lipid model system and evaluated via the Schaal Oven Test. After 96 hours, 150 and 200 mg·kg−1 oil of the wild and 14-4 genotype extracts, respectively, showed an antioxidant capacity similar to TBHQ (200 mg·kg−1 oil) in terms of peroxide values and odor. Thus, murtilla fruit extracts are a natural source of antioxidants for protecting lipidic foods, such as soybean oil. [es

  8. Preparation of novel cross-linked and octylated caseinates using a biphasic enzymatic procedure and their functional properties.

    Science.gov (United States)

    Zhang, Yaqiong; Niu, Yuge; Yao, Fangyi; Dai, Bona; Wang, Qin; Yu, Liangli Lucy

    2014-08-27

    A novel microbial transglutaminase-catalyzed aqueous-organic biphasic reaction system was successfully developed to prepare caseinate derivatives by cross-linking and incorporating nonpolar octyl tails for the first time. SDS-PAGE and (1)H NMR analysis confirmed that cross-linking and octyl conjugation occurred simultaneously. The octyl substitution degree (SD) was measured by (1)H NMR and used as an index to determine a suitable reaction condition. It was found that at the condition of 0.125% (w/v) protein concentration and 6 h of reaction time, the modified caseinate had the highest SD of 28.96%. The modified caseinate also had an increased surface hydrophobicity, better emulsifying activity, and improved thermal and salt stabilities. However, its emulsion stability or in vitro enzymatic digestibility was slightly lower than that of the native caseinate.

  9. Mass extraction container closure integrity physical testing method development for parenteral container closure systems.

    Science.gov (United States)

    Yoon, Seung-Yil; Sagi, Hemi; Goldhammer, Craig; Li, Lei

    2012-01-01

    Container closure integrity (CCI) is a critical factor to ensure that product sterility is maintained over its entire shelf life. Assuring the CCI during container closure (C/C) system qualification, routine manufacturing and stability is important. FDA guidance also encourages industry to develop a CCI physical testing method in lieu of sterility testing in a stability program. A mass extraction system has been developed to check CCI for a variety of container closure systems such as vials, syringes, and cartridges. Various types of defects (e.g., glass micropipette, laser drill, wire) were created and used to demonstrate a detection limit. Leakage, detected as mass flow in this study, changes as a function of defect length and diameter. Therefore, the morphology of defects has been examined in detail with fluid theories. This study demonstrated that a mass extraction system was able to distinguish between intact samples and samples with 2 μm defects reliably when the defect was exposed to air, water, placebo, or drug product (3 mg/mL concentration) solution. Also, it has been verified that the method was robust, and capable of determining the acceptance limit using 3σ for syringes and 6σ for vials. Sterile products must maintain their sterility over their entire shelf life. Container closure systems such as those found in syringes and vials provide a seal between rubber and glass containers. This seal must be ensured to maintain product sterility. A mass extraction system has been developed to check container closure integrity for a variety of container closure systems such as vials, syringes, and cartridges. In order to demonstrate the method's capability, various types of defects (e.g., glass micropipette, laser drill, wire) were created in syringes and vials and were tested. This study demonstrated that a mass extraction system was able to distinguish between intact samples and samples with 2 μm defects reliably when the defect was exposed to air, water

  10. An extraction-chromogenic system for vanadium(IV,V based on 2,3-dihydroxynaphtahlene

    Directory of Open Access Journals (Sweden)

    Gavazov Kiril B.

    2016-10-01

    Full Text Available A liquid-liquid extraction-chromogenic system for vanadium(IV, V containing 2,3-dihydroxynaphtahlene (DN, 2,3,5-triphenyl-2H-tetrazolium chloride (TTC, water and chloroform was studied in detail. When the vanadium is in the oxidation state of IV, the extracted species are aggregates containing three 1:2:1 (V:DN:TTC ion-pair units composed of triphenyltetrazolium cations (TT+ and chelate anions {[VIVO(DN(DNH]− (I and/or [VIV(OH(DN2]− (II}. When the initial oxidation state of vanadium is V and the DN concentration is high, vanadium(V is reduced by DN to a lower oxidation state, V(IV. However, at low DN concentration, vanadium(V can enter the organic phase as a part of an ion-pair consisting of TT+ and [VVO2(DN]− (III. The ground-state equilibrium geometries of the anions I, II, and III were optimized by quantum chemical calculations using BLYP/6-31++G⋆. The following characteristics were determined under the optimum conditions for VIV extraction: absorption maximum λmax = 333 nm, molar absorptivity ε333= 2.1x104 dm3 mol−1 cm−1, Sandell’s sensitivity SS = 2.4 ng cm−2, and fraction extracted E = 98%. The conditional extraction constant was calculated by two independent methods. The calibration graph was linear in the range 0.1-3.1 μg cm−3 (R2=0.9994 and the limit of detection was 0.03 μg cm−3.

  11. Column Extraction and Separation of Some Metal Ions by Diethylenetriamine Polysiloxane Immobilized Ligand System

    Directory of Open Access Journals (Sweden)

    Nizam M. El-Ashgar

    2008-01-01

    Full Text Available An extraction chromatographic solid porous polysiloxane functionalized by chelating diethylenetriamine ligand of the general formula P-(CH23-NH(CH22NH(CH22NH2, (Where P represents [Si-O]n siloxane network has been evaluated for the separation of Co(II, Ni(II and Cu(II from aqueous solutions. The chromatographic parameters of the separation method have been optimized. The ligand system retained Co(II, Cu(II and Zn(II effectively when used as a metal ion extractant by controlling the pH value. The ligand system also shows a good separation of a mixture of metal ions Co(II, Ni(II and Cu(II when used as chromatographic stationary phase. The optimum separation pH values were 4.5, 4 for Co(II and Ni(II respectively, while a solution of 0.1 M HNO3 was used to elute Cu(II. Metal ions were also preconcentrated at pH 5.5. The chemisorbed metal ions were regenerated from the solid extractant using 0.5 M HCl.

  12. Direct 3D powder printing of biphasic calcium phosphate scaffolds for substitution of complex bone defects.

    Science.gov (United States)

    Castilho, Miguel; Moseke, Claus; Ewald, Andrea; Gbureck, Uwe; Groll, Jürgen; Pires, Inês; Teßmar, Jörg; Vorndran, Elke

    2014-03-01

    The 3D printing technique based on cement powders is an excellent method for the fabrication of individual and complex bone substitutes even in the case of large defects. The outstanding bone remodeling capacity of biphasic calcium phosphates (BCPs) containing hydroxyapatite (HA) as well as tricalcium phosphate (TCP) in varying ratios makes the adaption of powder systems resulting in BCP materials to this fabrication technique a desirable aim. This study presents the synthesis and characterization of a novel powder system for the 3D printing process, intended for the production of complexly shaped BCP scaffolds by a hydraulic setting reaction of calcium carbonate and TCP with phosphoric acid. The HA/TCP ratio in the specimens could be tailored by the calcium/phosphate ratio of the starting powder. The scaffolds could be fabricated with a dimensional accuracy of >96.5% and a minimal macro pore size of 300 µm. Independent of the phase composition the printed specimens showed a microporosity of approximately 68%, while the compressive strength strongly depended on the chemical composition and increased with rising TCP content in the scaffolds to a maximum of 1.81 MPa. Post-treatment of the scaffolds with a polylactic-co-glycolic acid-solution enhanced the mechanical properties by a factor of 8. In vitro studies showed that all BCP scaffolds were cytocompatible and enhanced the cell viability as well as the cell proliferation, as compared with pure TCP. Cell proliferation is even better on BCP when compared to HA and cell viability is in a similar range on these materials.

  13. A technique system for the measurement, reconstruction and character extraction of rice plant architecture.

    Directory of Open Access Journals (Sweden)

    Xumeng Li

    Full Text Available This study developed a technique system for the measurement, reconstruction, and trait extraction of rice canopy architectures, which have challenged functional-structural plant modeling for decades and have become the foundation of the design of ideo-plant architectures. The system uses the location-separation-measurement method (LSMM for the collection of data on the canopy architecture and the analytic geometry method for the reconstruction and visualization of the three-dimensional (3D digital architecture of the rice plant. It also uses the virtual clipping method for extracting the key traits of the canopy architecture such as the leaf area, inclination, and azimuth distribution in spatial coordinates. To establish the technique system, we developed (i simple tools to measure the spatial position of the stem axis and azimuth of the leaf midrib and to capture images of tillers and leaves; (ii computer software programs for extracting data on stem diameter, leaf nodes, and leaf midrib curves from the tiller images and data on leaf length, width, and shape from the leaf images; (iii a database of digital architectures that stores the measured data and facilitates the reconstruction of the 3D visual architecture and the extraction of architectural traits; and (iv computation algorithms for virtual clipping to stratify the rice canopy, to extend the stratified surface from the horizontal plane to a general curved surface (including a cylindrical surface, and to implement in silico. Each component of the technique system was quantitatively validated and visually compared to images, and the sensitivity of the virtual clipping algorithms was analyzed. This technique is inexpensive and accurate and provides high throughput for the measurement, reconstruction, and trait extraction of rice canopy architectures. The technique provides a more practical method of data collection to serve functional-structural plant models of rice and for the

  14. Thermal enhanced vapor extraction systems: Design, application and performance prediction including contaminant behavior

    International Nuclear Information System (INIS)

    Phelan, J.M.; Webb, S.W.

    1994-01-01

    Soil heating technologies have been proposed as a method to accelerate contaminant removal from subsurface soils. These methods include the use of hot air, steam, conductive heaters, in-situ resistive heating and in-situ radiofrequency heating (Buettner et.al., EPA, Dev et.al., Heath et.al.). Criteria for selection of a particular soil heating technology is a complex function of contaminant and soil properties, and efficiency in energy delivery and contaminant removal technologies. The work presented here seeks to expand the understanding of the interactions of subsurface water, contaminant, heat and vacuum extraction through model predictions and field data collection. Field demonstration will involve the combination of two soil heating technologies (resistive and dielectric) with a vacuum vapor extraction system and will occur during the summer of 1994

  15. Disposable and removable nucleic acid extraction and purification cartridges for automated flow-through systems

    Science.gov (United States)

    Regan, John Frederick

    2014-09-09

    Removable cartridges are used on automated flow-through systems for the purpose of extracting and purifying genetic material from complex matrices. Different types of cartridges are paired with specific automated protocols to concentrate, extract, and purifying pathogenic or human genetic material. Their flow-through nature allows large quantities sample to be processed. Matrices may be filtered using size exclusion and/or affinity filters to concentrate the pathogen of interest. Lysed material is ultimately passed through a filter to remove the insoluble material before the soluble genetic material is delivered past a silica-like membrane that binds the genetic material, where it is washed, dried, and eluted. Cartridges are inserted into the housing areas of flow-through automated instruments, which are equipped with sensors to ensure proper placement and usage of the cartridges. Properly inserted cartridges create fluid- and air-tight seals with the flow lines of an automated instrument.

  16. Biphasic calcium phosphate–casein bone graft fortified with Cassia ...

    Indian Academy of Sciences (India)

    The results revealed that CO extract-incorporated bone implants possessed better compression strength and it was able to induce proliferation and enhance alkaline phosphatase activity in SaOS-2 cells. The implant proves to be promising for bone tissue engineering, and hence it demands further in vivo evaluation.

  17. Liquid-Liquid Extraction in Systems Containing Butanol and Ionic Liquids – A Review

    Directory of Open Access Journals (Sweden)

    Kubiczek Artur

    2017-03-01

    Full Text Available Room-temperature ionic liquids (RTILs are a moderately new class of liquid substances that are characterized by a great variety of possible anion-cation combinations giving each of them different properties. For this reason, they have been termed as designer solvents and, as such, they are particularly promising for liquid-liquid extraction, which has been quite intensely studied over the last decade. This paper concentrates on the recent liquid-liquid extraction studies involving ionic liquids, yet focusing strictly on the separation of n-butanol from model aqueous solutions. Such research is undertaken mainly with the intention of facilitating biological butanol production, which is usually carried out through the ABE fermentation process. So far, various sorts of RTILs have been tested for this purpose while mostly ternary liquid-liquid systems have been investigated. The industrial design of liquid-liquid extraction requires prior knowledge of the state of thermodynamic equilibrium and its relation to the process parameters. Such knowledge can be obtained by performing a series of extraction experiments and employing a certain mathematical model to approximate the equilibrium. There are at least a few models available but this paper concentrates primarily on the NRTL equation, which has proven to be one of the most accurate tools for correlating experimental equilibrium data. Thus, all the presented studies have been selected based on the accepted modeling method. The reader is also shown how the NRTL equation can be used to model liquid-liquid systems containing more than three components as it has been the authors’ recent area of expertise.

  18. Protocol: A high-throughput DNA extraction system suitable for conifers

    Directory of Open Access Journals (Sweden)

    Rajora Om P

    2008-08-01

    Full Text Available Abstract Background High throughput DNA isolation from plants is a major bottleneck for most studies requiring large sample sizes. A variety of protocols have been developed for DNA isolation from plants. However, many species, including conifers, have high contents of secondary metabolites that interfere with the extraction process or the subsequent analysis steps. Here, we describe a procedure for high-throughput DNA isolation from conifers. Results We have developed a high-throughput DNA extraction protocol for conifers using an automated liquid handler and modifying the Qiagen MagAttract Plant Kit protocol. The modifications involve change to the buffer system and improving the protocol so that it almost doubles the number of samples processed per kit, which significantly reduces the overall costs. We describe two versions of the protocol: one for medium-throughput (MTP and another for high-throughput (HTP DNA isolation. The HTP version works from start to end in the industry-standard 96-well format, while the MTP version provides higher DNA yields per sample processed. We have successfully used the protocol for DNA extraction and genotyping of thousands of individuals of several spruce and a pine species. Conclusion A high-throughput system for DNA extraction from conifer needles and seeds has been developed and validated. The quality of the isolated DNA was comparable with that obtained from two commonly used methods: the silica-spin column and the classic CTAB protocol. Our protocol provides a fully automatable and cost effective solution for processing large numbers of conifer samples.

  19. DiMeX: A Text Mining System for Mutation-Disease Association Extraction.

    Science.gov (United States)

    Mahmood, A S M Ashique; Wu, Tsung-Jung; Mazumder, Raja; Vijay-Shanker, K

    2016-01-01

    The number of published articles describing associations between mutations and diseases is increasing at a fast pace. There is a pressing need to gather such mutation-disease associations into public knowledge bases, but manual curation slows down the growth of such databases. We have addressed this problem by developing a text-mining system (DiMeX) to extract mutation to disease associations from publication abstracts. DiMeX consists of a series of natural language processing modules that preprocess input text and apply syntactic and semantic patterns to extract mutation-disease associations. DiMeX achieves high precision and recall with F-scores of 0.88, 0.91 and 0.89 when evaluated on three different datasets for mutation-disease associations. DiMeX includes a separate component that extracts mutation mentions in text and associates them with genes. This component has been also evaluated on different datasets and shown to achieve state-of-the-art performance. The results indicate that our system outperforms the existing mutation-disease association tools, addressing the low precision problems suffered by most approaches. DiMeX was applied on a large set of abstracts from Medline to extract mutation-disease associations, as well as other relevant information including patient/cohort size and population data. The results are stored in a database that can be queried and downloaded at http://biotm.cis.udel.edu/dimex/. We conclude that this high-throughput text-mining approach has the potential to significantly assist researchers and curators to enrich mutation databases.

  20. Modeling Biphasic Environmental Decay of Pathogens and Implications for Risk Analysis.

    Science.gov (United States)

    Brouwer, Andrew F; Eisenberg, Marisa C; Remais, Justin V; Collender, Philip A; Meza, Rafael; Eisenberg, Joseph N S

    2017-02-21

    As the appreciation for the importance of the environment in infectious disease transmission has grown, so too has interest in pathogen fate and transport. Fate has been traditionally described by simple exponential decay, but there is increasing recognition that some pathogens demonstrate a biphasic pattern of decay-fast followed by slow. While many have attributed this behavior to population heterogeneity, we demonstrate that biphasic dynamics can arise through a number of plausible mechanisms. We examine the identifiability of a general model encompassing three such mechanisms: population heterogeneity, hardening off, and the existence of viable-but-not-culturable states. Although the models are not fully identifiable from longitudinal sampling studies of pathogen concentrations, we use a differential algebra approach to determine identifiable parameter combinations. Through case studies using Cryptosporidium and Escherichia coli, we show that failure to consider biphasic pathogen dynamics can lead to substantial under- or overestimation of disease risks and pathogen concentrations, depending on the context. More reliable models for environmental hazards and human health risks are possible with an improved understanding of the conditions in which biphasic die-off is expected. Understanding the mechanisms of pathogen decay will ultimately enhance our control efforts to mitigate exposure to environmental contamination.

  1. Occurrence of amylose-lipid complexes in teff and maize starch biphasic pastes

    CSIR Research Space (South Africa)

    Wokadala, OC

    2012-09-01

    Full Text Available The occurrence of amylose–lipid complexes was determined in maize and teff starch biphasic pastes i.e. peak viscosity pastes at short and prolonged pasting times. Maize and teff starches were pasted for 11.5 and 130 min with or without added stearic...

  2. A New Type of Biphasic Calcium Phosphate Cement as a Gentamicin Carrier for Osteomyelitis

    Directory of Open Access Journals (Sweden)

    Wen-Yu Su

    2013-01-01

    Full Text Available Osteomyelitis therapy is a long-term and inconvenient procedure for a patient. Antibiotic-loaded bone cements are both a complementary and alternative treatment option to intravenous antibiotic therapy for the treatment of osteomyelitis. In the current study, the biphasic calcium phosphate cement (CPC, called α-TCP/HAP (α-tricalcium phosphate/hydroxyapatite biphasic cement, was prepared as an antibiotics carrier for osteomyelitis. The developed biphasic cement with a microstructure of α-TCP surrounding the HAP has a fast setting time which will fulfill the clinical demand. The X-ray diffraction and Fourier transform infrared spectrometry analyses showed the final phase to be HAP, the basic bone mineral, after setting for a period of time. Scanning electron microscopy revealed a porous structure with particle sizes of a few micrometers. The addition of gentamicin in α-TCP/HAP would delay the transition of α-TCP but would not change the final-phase HAP. The gentamicin-loaded α-TCP/HAP supplies high doses of the antibiotic during the initial 24 hours when they are soaked in phosphate buffer solution (PBS. Thereafter, a slower drug release is produced, supplying minimum inhibitory concentration until the end of the experiment (30 days. Studies of growth inhibition of Staphylococcus aureus and Pseudomonas aeruginosa in culture indicated that gentamicin released after 30 days from α-TCP/HAP biphasic cement retained antibacterial activity.

  3. A pilot trial of square biphasic pulse deep brain stimulation for dystonia: The BIP dystonia study.

    Science.gov (United States)

    Almeida, Leonardo; Martinez-Ramirez, Daniel; Ahmed, Bilal; Deeb, Wissam; Jesus, Sol De; Skinner, Jared; Terza, Matthew J; Akbar, Umer; Raike, Robert S; Hass, Chris J; Okun, Michael S

    2017-04-01

    Dystonia often has inconsistent benefits and requires more energy-demanding DBS settings. Studies suggest that squared biphasic pulses could provide significant clinical benefit; however, dystonia patients have not been explored. To assess safety and tolerability of square biphasic DBS in dystonia patients. This study included primary generalized or cervical dystonia patients with bilateral GPi DBS. Square biphasic pulses were implemented and patients were assessed at baseline, immediately postwashout, post-30-minute washout, 1 hour post- and 2 hours postinitiation of investigational settings. Ten participants completed the study. There were no patient-reported or clinician-observed side effects. There was improvement across time on the Toronto Western Spasmodic Torticollis Rating Scale (χ 2  = 10.7; P = 0.031). Similar improvement was detected in objective gait measurements. Square biphasic stimulation appears safe and feasible in dystonia patients with GPi DBS. Further studies are needed to evaluate possible effectiveness particularly in cervical and gait features. © 2016 International Parkinson and Movement Disorder Society. © 2017 International Parkinson and Movement Disorder Society.

  4. Preparation of highly infective Leishmania promastigotes by cultivation on SNB-9 biphasic medium.

    Science.gov (United States)

    Grekov, Igor; Svobodová, Milena; Nohýnková, Eva; Lipoldová, Marie

    2011-12-01

    Protozoan hemoflagellates Leishmania are causative agents of leishmaniases and an important biological model for study of host-pathogen interaction. A wide range of methods of Leishmania cultivation on both biphasic and liquid media is available. Biphasic media are considered to be superior for initial isolation of the parasites and obtaining high promastigote infectivity; however, liquid media are more suitable for large-scale experiments. The aim of the present study was the adaptation and optimization of the cultivation of Leishmania promastigotes on a biphasic SNB-9 (saline-neopeptone-blood 9) medium that was originally developed for Trypanosoma cultivation and combines the advantages of biphasic and liquid media. SNB-9 medium is characterized with a large volume of the liquid phase, which facilitates the manipulation with the culture and provides parasite yields comparable to parasite yields on such liquid medium as Schneider's Insect Medium. We demonstrate that SNB-9 very considerably surpasses Schneider's Insect Medium in in vitro infectivity of the parasites. Additionally, we show that the ratio of apoptotic parasites, which are important for the infectivity of the inoculum, in Leishmania culture in SNB-9 is higher than in Leishmania culture in Schneider's Insect Medium. Thus, we demonstrate that the cultivation of Leishmania on SNB-9 reliably yields highly infective promastigotes suitable for experimental infection. Copyright © 2011 Elsevier B.V. All rights reserved.

  5. A knowledge-based decision support system in bioinformatics: an application to protein complex extraction

    Directory of Open Access Journals (Sweden)

    Fiannaca Antonino

    2013-01-01

    Full Text Available Abstract Background We introduce a Knowledge-based Decision Support System (KDSS in order to face the Protein Complex Extraction issue. Using a Knowledge Base (KB coding the expertise about the proposed scenario, our KDSS is able to suggest both strategies and tools, according to the features of input dataset. Our system provides a navigable workflow for the current experiment and furthermore it offers support in the configuration and running of every processing component of that workflow. This last feature makes our system a crossover between classical DSS and Workflow Management Systems. Results We briefly present the KDSS' architecture and basic concepts used in the design of the knowledge base and the reasoning component. The system is then tested using a subset of Saccharomyces cerevisiae Protein-Protein interaction dataset. We used this subset because it has been well studied in literature by several research groups in the field of complex extraction: in this way we could easily compare the results obtained through our KDSS with theirs. Our system suggests both a preprocessing and a clustering strategy, and for each of them it proposes and eventually runs suited algorithms. Our system's final results are then composed of a workflow of tasks, that can be reused for other experiments, and the specific numerical results for that particular trial. Conclusions The proposed approach, using the KDSS' knowledge base, provides a novel workflow that gives the best results with regard to the other workflows produced by the system. This workflow and its numeric results have been compared with other approaches about PPI network analysis found in literature, offering similar results.

  6. Multiple Adaptive Neuro-Fuzzy Inference System with Automatic Features Extraction Algorithm for Cervical Cancer Recognition

    Directory of Open Access Journals (Sweden)

    Mohammad Subhi Al-batah

    2014-01-01

    Full Text Available To date, cancer of uterine cervix is still a leading cause of cancer-related deaths in women worldwide. The current methods (i.e., Pap smear and liquid-based cytology (LBC to screen for cervical cancer are time-consuming and dependent on the skill of the cytopathologist and thus are rather subjective. Therefore, this paper presents an intelligent computer vision system to assist pathologists in overcoming these problems and, consequently, produce more accurate results. The developed system consists of two stages. In the first stage, the automatic features extraction (AFE algorithm is performed. In the second stage, a neuro-fuzzy model called multiple adaptive neuro-fuzzy inference system (MANFIS is proposed for recognition process. The MANFIS contains a set of ANFIS models which are arranged in parallel combination to produce a model with multi-input-multioutput structure. The system is capable of classifying cervical cell image into three groups, namely, normal, low-grade squamous intraepithelial lesion (LSIL and high-grade squamous intraepithelial lesion (HSIL. The experimental results prove the capability of the AFE algorithm to be as effective as the manual extraction by human experts, while the proposed MANFIS produces a good classification performance with 94.2% accuracy.

  7. Information extraction approaches to unconventional data sources for "Injury Surveillance System": the case of newspapers clippings.

    Science.gov (United States)

    Berchialla, Paola; Scarinzi, Cecilia; Snidero, Silvia; Rahim, Yousif; Gregori, Dario

    2012-04-01

    Injury Surveillance Systems based on traditional hospital records or clinical data have the advantage of being a well established, highly reliable source of information for making an active surveillance on specific injuries, like choking in children. However, they suffer the drawback of delays in making data available to the analysis, due to inefficiencies in data collection procedures. In this sense, the integration of clinical based registries with unconventional data sources like newspaper articles has the advantage of making the system more useful for early alerting. Usage of such sources is difficult since information is only available in the form of free natural-language documents rather than structured databases as required by traditional data mining techniques. Information Extraction (IE) addresses the problem of transforming a corpus of textual documents into a more structured database. In this paper, on a corpora of Italian newspapers articles related to choking in children due to ingestion/inhalation of foreign body we compared the performance of three IE algorithms- (a) a classical rule based system which requires a manual annotation of the rules; (ii) a rule based system which allows for the automatic building of rules; (b) a machine learning method based on Support Vector Machine. Although some useful indications are extracted from the newspaper clippings, this approach is at the time far from being routinely implemented for injury surveillance purposes.

  8. Multiple adaptive neuro-fuzzy inference system with automatic features extraction algorithm for cervical cancer recognition.

    Science.gov (United States)

    Al-batah, Mohammad Subhi; Isa, Nor Ashidi Mat; Klaib, Mohammad Fadel; Al-Betar, Mohammed Azmi

    2014-01-01

    To date, cancer of uterine cervix is still a leading cause of cancer-related deaths in women worldwide. The current methods (i.e., Pap smear and liquid-based cytology (LBC)) to screen for cervical cancer are time-consuming and dependent on the skill of the cytopathologist and thus are rather subjective. Therefore, this paper presents an intelligent computer vision system to assist pathologists in overcoming these problems and, consequently, produce more accurate results. The developed system consists of two stages. In the first stage, the automatic features extraction (AFE) algorithm is performed. In the second stage, a neuro-fuzzy model called multiple adaptive neuro-fuzzy inference system (MANFIS) is proposed for recognition process. The MANFIS contains a set of ANFIS models which are arranged in parallel combination to produce a model with multi-input-multioutput structure. The system is capable of classifying cervical cell image into three groups, namely, normal, low-grade squamous intraepithelial lesion (LSIL) and high-grade squamous intraepithelial lesion (HSIL). The experimental results prove the capability of the AFE algorithm to be as effective as the manual extraction by human experts, while the proposed MANFIS produces a good classification performance with 94.2% accuracy.

  9. Statistical Feature Extraction for Fault Locations in Nonintrusive Fault Detection of Low Voltage Distribution Systems

    Directory of Open Access Journals (Sweden)

    Hsueh-Hsien Chang

    2017-04-01

    Full Text Available This paper proposes statistical feature extraction methods combined with artificial intelligence (AI approaches for fault locations in non-intrusive single-line-to-ground fault (SLGF detection of low voltage distribution systems. The input features of the AI algorithms are extracted using statistical moment transformation for reducing the dimensions of the power signature inputs measured by using non-intrusive fault monitoring (NIFM techniques. The data required to develop the network are generated by simulating SLGF using the Electromagnetic Transient Program (EMTP in a test system. To enhance the identification accuracy, these features after normalization are given to AI algorithms for presenting and evaluating in this paper. Different AI techniques are then utilized to compare which identification algorithms are suitable to diagnose the SLGF for various power signatures in a NIFM system. The simulation results show that the proposed method is effective and can identify the fault locations by using non-intrusive monitoring techniques for low voltage distribution systems.

  10. Reverse micellar extraction systems for the purification of pharmaceutical grade plasmid DNA.

    Science.gov (United States)

    Streitner, Nadine; Voss, Carsten; Flaschel, Erwin

    2007-08-31

    Plasmid DNA as an active pharmaceutical ingredient (API) is gaining more and more importance. For the production of multigram quantities of this substance robust and scalable processes comprising several purification steps have to be designed. One main challenge is the initial separation of plasmid DNA and RNA in such a purification scheme. In this study we investigated the distribution of plasmid DNA and RNA in reverse micellar two-phase systems which is considered to be the basis for the development of an extractive purification step that can easily be integrated into common processes. For this purpose the distribution of the 4.6kb plasmid pUT649 and Escherichia coli RNA in systems comprising isooctane, ethylhexanol, and the surfactant methyltrioctylammoniumchloride (TOMAC) under the influence of different salts was studied. Anion concentrations at which the partitioning behaviour for nucleic acids inverted (inversion point) were identified. Systems capable of separating RNA from plasmid DNA were further analysed and applied to extract RNA from plasmid DNA out of a preconditioned cleared lysate. The capability of reverse micellar systems for plasmid form separation was also shown by capillary and agarose gel electrophoresis.

  11. Caustic-Side Solvent-Extraction Modeling for Hanford Interim Pretreatment System

    Energy Technology Data Exchange (ETDEWEB)

    Moyer, B.A.; Birdwell, J.F.; Delmau, L. H.; McFarlane, J.

    2008-06-01

    The purpose of this work is to examine the applicability of the Caustic-Side Solvent Extraction (CSSX) process for the removal of cesium from Hanford tank-waste supernatant solutions in support of the Hanford Interim Pretreatment System (IPS). The Hanford waste types are more challenging than those at the Savannah River Site (SRS) in that they contain significantly higher levels of potassium, the chief competing ion in the extraction of cesium. It was confirmed by use of the CSSX model that the higher levels of potassium depress the cesium distribution ratio (DCs), as validated by measurement of DCs values for four of eight specified Hanford waste-simulant compositions. The model predictions were good to an apparent standard error of ±11%. It is concluded from batch distribution experiments, physical-property measurements, equilibrium modeling, flowsheet calculations, and contactor sizing that the CSSX process as currently employed for cesium removal from alkaline salt waste at the SRS is capable of treating similar Hanford tank feeds. For the most challenging waste composition, 41 stages would be required to provide a cesium decontamination factor (DF) of 5000 and a concentration factor (CF) of 5. Commercial contacting equipment with rotor diameters of 10 in. for extraction and 5 in. for stripping should have the capacity to meet throughput requirements, but testing will be required to confirm that the needed efficiency and hydraulic performance are actually obtainable. Markedly improved flowsheet performance was calculated for a new solvent formulation employing the more soluble cesium extractant BEHBCalixC6 used with alternative scrub and strip solutions, respectively 0.1 M NaOH and 10 mM boric acid. The improved system can meet minimum requirements (DF = 5000 and CF = 5) with 17 stages or more ambitious goals (DF = 40,000 and CF = 15) with 19 stages. Potential benefits of further research and development are identified that would lead to reduced costs, greater

  12. Leaf-cutter ant fungus gardens are biphasic mixed microbial bioreactors that convert plant biomass to polyols with biotechnological applications.

    Science.gov (United States)

    Somera, Alexandre F; Lima, Adriel M; Dos Santos-Neto, Álvaro J; Lanças, Fernando M; Bacci, Maurício

    2015-07-01

    Leaf-cutter ants use plant matter to culture the obligate mutualistic basidiomycete Leucoagaricus gongylophorus. This fungus mediates ant nutrition on plant resources. Furthermore, other microbes living in the fungus garden might also contribute to plant digestion. The fungus garden comprises a young sector with recently incorporated leaf fragments and an old sector with partially digested plant matter. Here, we show that the young and old sectors of the grass-cutter Atta bisphaerica fungus garden operate as a biphasic solid-state mixed fermenting system. An initial plant digestion phase occurred in the young sector in the fungus garden periphery, with prevailing hemicellulose and starch degradation into arabinose, mannose, xylose, and glucose. These products support fast microbial growth but were mostly converted into four polyols. Three polyols, mannitol, arabitol, and inositol, were secreted by L. gongylophorus, and a fourth polyol, sorbitol, was likely secreted by another, unidentified, microbe. A second plant digestion phase occurred in the old sector, located in the fungus garden core, comprising stocks of microbial biomass growing slowly on monosaccharides and polyols. This biphasic operation was efficient in mediating symbiotic nutrition on plant matter: the microbes, accounting for 4% of the fungus garden biomass, converted plant matter biomass into monosaccharides and polyols, which were completely consumed by the resident ants and microbes. However, when consumption was inhibited through laboratory manipulation, most of the plant polysaccharides were degraded, products rapidly accumulated, and yields could be preferentially switched between polyols and monosaccharides. This feature might be useful in biotechnology. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

  13. Development of novel solvent extraction system by utilizing the metal ions excitation with ultraviolet pulse laser

    International Nuclear Information System (INIS)

    Saeki, Morihisa; Sasaki, Yuji; Yokoyama, Atsushi

    2010-01-01

    Novel liquid-liquid extraction technique was developed using ultraviolet pulse laser. The liquid-liquid system was composed of pure water and the 1-octanol solution of EuCl 3 and TODGA (TODGA = N,N,N',N'-tetraoctyl-diglycolamide). The Eu 3+ ion, which was formed to be the Eu 3+ (TODGA) n complex in 1-octanol, was reduced to Eu 2+ by irradiation of fourth harmonic of Nd:YAG laser (266 nm). The Eu 2+ ion was stabilized by addition of 15-Crown-5 (15C5). The observation by in-situ emission spectroscopy showed that the Eu 2+ ion reduced by the 266 nm-laser irradiation resulted in back-extraction of Eu from the 1-octanol solution to the water. The emission spectrum observed in 1-octanol suggested the change from the Eu 3+ (TODGA) n to the Eu 2+ (15C5) m complex after the reduction by the 266 nm laser. Time dependence of the concentration of Eu 2+ (15C5) m was investigated at the aqueous phase, the organic one and their interface. The results suggest that (1) rapid formation of Eu 2+ (15C5) m in 1-octanol after the irradiation of the 266 nm laser, (2) slow diffusion of Eu 2+ (15C5) m in 1-octanol, and (3) existence of time-lag between the formation of Eu 2+ (15C5) m in 1-octanol and its back-extraction to the water. (author)

  14. Antinociceptive Activity of Stephanolepis hispidus Skin Aqueous Extract Depends Partly on Opioid System Activation

    Directory of Open Access Journals (Sweden)

    Hugo Castro-Faria-Neto

    2013-04-01

    Full Text Available Stephanolepis hispidus is one of the most common filefish species in Brazil. Its skin is traditionally used as a complementary treatment for inflammatory disorders. However, there are very few studies on chemical and pharmacological properties using the skin of this fish. This study was undertaken in order to investigate the effect of aqueous crude extract of S. hispidus skin (SAE in different nociception models. Here, we report that intraperitoneal administration of SAE inhibited the abdominal constrictions induced by acetic acid in mice. In addition to the effect seen in the abdominal constriction model, SAE was also able to inhibit the hyperalgesia induced by carrageenan and prostaglandin E2 (PGE2 in mice. This potent antinociceptive effect was observed in the hot plate model too, but not in tail-flick test. Naloxone, an opioid receptor antagonist, was able to block the antinociceptive effect of SAE in the abdominal constriction and hot plate models. In addition, SAE did not present cytotoxic or genotoxic effect in human peripheral blood cells. Our results suggest that aqueous crude extract from S. hispidus skin has antinociceptive activity in close relationship with the partial activation of opioid receptors in the nervous system. Moreover, aqueous crude extract from S. hispidus skin does not present toxicity and is therefore endowed with the potential for pharmacological control of pain.

  15. Electromagnetic Coupling Between High Intensity LHC Beams and the Synchrotron Radiation Monitor Light Extraction System

    CERN Document Server

    Andreazza, W; Bravin, E; Caspers, F; Garlasch`e, M; Gras, J; Goldblatt, A; Lefevre, T; Jones, R; Metral, E; Nosych, A; Roncarolo_, F; Salvant, B; Trad, G; Veness, R; Vollinger, C; Wendt, M

    2013-01-01

    The CERN LHC is equipped with two Synchrotron Radiation Monitor (BSRT) systems used to characterise transverse and longitudinal beam distributions. Since the end of the 2011 LHC run the light extraction system, based on a retractable mirror, has suffered deformation and mechanical failure that is correlated to the increase in beam intensity. Temperature probes have associated these observations to a strong heating of the mirror support with a dependence on the longitudinal bunch length and shape, indicating the origin as electromagnetic coupling between the beam and the structure. This paper combines all this information with the aim of characterising and improving the system in view of its upgrade during the current LHC shutdown. Beam-based observations are presented along with electromagnetic and thermomechanical simulations and complemented by laboratory measurements, including the study of the RF properties of different mirror bulk and coating materials.

  16. 3D information extraction based on a novel x ray imaging system

    Science.gov (United States)

    Yu, Chunyu; Kong, Lingli; Zhang, Junju; Zhang, Shengdong

    2011-08-01

    In this paper, a novel x-ray imaging system was introduced. It was a CCD based system, but different from the traditional CCD based x-ray imaging system, which was composed of the x-ray intensifying screen, the CCD and the low light level image intensifier, specially using the zoom lens for coupling. Zoom lens can give a continuous variable visual field, which not only reduce the geometrical blur but also can produce several image pairs for stereo imaging. It is convenient for three dimension information extraction from a group of two dimension x-ray images and is valuable for stereovision radiography in the application of medical diagnosis, security checking, non-destructive testing, and industry detection. This stereo imaging method is also referential for the three dimension reconstruction daily living.

  17. Advanced Recovery and Integrated Extraction System (ARIES) program plan. Rev. 1

    International Nuclear Information System (INIS)

    Nelson, T.O.; Massey, P.W.; Cremers, T.L.

    1996-01-01

    The Advanced Recovery and Integrated Extraction System (ARIES) demonstration combines various technologies, some of which were/are being developed under previous/other Department of Energy (DOE) funded programs. ARIES is an overall processing system for the dismantlement of nuclear weapon primaries. The program will demonstrate dismantlement of nuclear weapons and retrieval of the plutonium into a form that is compatible with long term storage and that is inspectable in an unclassified form appropriate for the application of traditional international safeguards. The success of the ARIES demonstration would lead to the development of a transportable modular or other facility type systems for weapons dismantlement to be used at other DOE sites as well as in other countries

  18. Design, demonstration and evaluation of a thermal enhanced vapor extraction system

    Energy Technology Data Exchange (ETDEWEB)

    Phelan, J.; Reavis, B.; Swanson, J. [and others

    1997-08-01

    The Thermal Enhanced Vapor Extraction System (TEVES), which combines powerline frequency heating (PLF) and radio frequency (RF) heating with vacuum soil vapor extraction, was used to effectively remove volatile organic compounds (VOCs) and semi-volatile organic compounds (SVOCs) from a pit in the chemical waste landfill (CWL) at Sandia National Laboratories (SNL) within a two month heating period. Volume average temperatures of 83{degrees}C and 112{degrees}C were reached for the PLF and RF heating periods, respectively, within the 15 ft x 45 ft x 18.5 ft deep treated volume. This resulted in the removal of 243 lb of measured toxic organic compounds (VOCs and SVOCs), 55 gallons of oil, and 11,000 gallons of water from the site. Reductions of up to 99% in total chromatographic organics (TCO) was achieved in the heated zone. Energy balance calculations for the PLF heating period showed that 36.4% of the heat added went to heating the soil, 38.5% went to evaporating water and organics, 4.2% went to sensible heat in the water, 7.1% went to heating the extracted air, and 6.6% was lost. For the RF heating period went to heating the soil, 23.5% went to evaporating water and organics, 2.4% went to sensible heat in the water, 7.5% went to heating extracted air, and 9.7% went to losses. Energy balance closure was 92.8% for the PLF heating and 98% for the RF heating. The energy input requirement per unit soil volume heated per unit temperature increase was 1.63 kWH/yd{sup 3}-{degrees}C for PLF heating and 0.73 kWH/yd{sup 3}{degrees}C for RF heating.

  19. Design, demonstration and evaluation of a thermal enhanced vapor extraction system

    International Nuclear Information System (INIS)

    Phelan, J.; Reavis, B.; Swanson, J.

    1997-08-01

    The Thermal Enhanced Vapor Extraction System (TEVES), which combines powerline frequency heating (PLF) and radio frequency (RF) heating with vacuum soil vapor extraction, was used to effectively remove volatile organic compounds (VOCs) and semi-volatile organic compounds (SVOCs) from a pit in the chemical waste landfill (CWL) at Sandia National Laboratories (SNL) within a two month heating period. Volume average temperatures of 83 degrees C and 112 degrees C were reached for the PLF and RF heating periods, respectively, within the 15 ft x 45 ft x 18.5 ft deep treated volume. This resulted in the removal of 243 lb of measured toxic organic compounds (VOCs and SVOCs), 55 gallons of oil, and 11,000 gallons of water from the site. Reductions of up to 99% in total chromatographic organics (TCO) was achieved in the heated zone. Energy balance calculations for the PLF heating period showed that 36.4% of the heat added went to heating the soil, 38.5% went to evaporating water and organics, 4.2% went to sensible heat in the water, 7.1% went to heating the extracted air, and 6.6% was lost. For the RF heating period went to heating the soil, 23.5% went to evaporating water and organics, 2.4% went to sensible heat in the water, 7.5% went to heating extracted air, and 9.7% went to losses. Energy balance closure was 92.8% for the PLF heating and 98% for the RF heating. The energy input requirement per unit soil volume heated per unit temperature increase was 1.63 kWH/yd 3 -degrees C for PLF heating and 0.73 kWH/yd 3 degrees C for RF heating

  20. Viability in the production of a drug extracted from Ananas comosus by a flat membrane system

    Directory of Open Access Journals (Sweden)

    Francisco Luiz Gumes Lopes

    2012-06-01

    Full Text Available The aim of this work was to study the production of e bromelain from the Ananas comosus L. Merril, by determining the process conditions using flat membranes. The production system modeling generated a hyperbolical curve and the optimization by response surfaces showed an influence of the transmembrane pressure higher than the pH influence. The cost of the production of bromelain from A. comosus was estimated 9 to 13 times lower than Sigma's retail sales price and 6.5 to 8.5 times lower than when this enzyme was obtained through a liquid-liquid extraction, which showed the economical feasibility of the process.

  1. Automated concept and relationship extraction for the semi-automated ontology management (SEAM) system.

    Science.gov (United States)

    Doing-Harris, Kristina; Livnat, Yarden; Meystre, Stephane

    2015-01-01

    We develop medical-specialty specific ontologies that contain the settled science and common term usage. We leverage current practices in information and relationship extraction to streamline the ontology development process. Our system combines different text types with information and relationship extraction techniques in a low overhead modifiable system. Our SEmi-Automated ontology Maintenance (SEAM) system features a natural language processing pipeline for information extraction. Synonym and hierarchical groups are identified using corpus-based semantics and lexico-syntactic patterns. The semantic vectors we use are term frequency by inverse document frequency and context vectors. Clinical documents contain the terms we want in an ontology. They also contain idiosyncratic usage and are unlikely to contain the linguistic constructs associated with synonym and hierarchy identification. By including both clinical and biomedical texts, SEAM can recommend terms from those appearing in both document types. The set of recommended terms is then used to filter the synonyms and hierarchical relationships extracted from the biomedical corpus. We demonstrate the generality of the system across three use cases: ontologies for acute changes in mental status, Medically Unexplained Syndromes, and echocardiogram summary statements. Across the three uses cases, we held the number of recommended terms relatively constant by changing SEAM's parameters. Experts seem to find more than 300 recommended terms to be overwhelming. The approval rate of recommended terms increased as the number and specificity of clinical documents in the corpus increased. It was 60% when there were 199 clinical documents that were not specific to the ontology domain and 90% when there were 2879 documents very specific to the target domain. We found that fewer than 100 recommended synonym groups were also preferred. Approval rates for synonym recommendations remained low varying from 43% to 25% as the

  2. Factors influencing the thermodynamic isotope effect of lithium in polyetherlithium liquid-liquid extraction systems

    International Nuclear Information System (INIS)

    Fu Lian; Fang Shengqiang; Yao Zhongqi; Gao Zhichang; Tan Ganzhu

    1989-01-01

    The published data up to now concerning polyether-lithium liquid-liquid extraction systems, can be summarized by the equation, ε p = (α-1)/[1 + 0.46(1-P)], where α denotes the isotope separation factor; P - the ratio of the lithium concentration in the organic phase to the initial concentration of crown ethers; ε p -the enrichment coefficient as P = 100%. Based on the changes in ε p , P, α and D(distribution ratio), the functions of factors such as polyether's structure, polyether's side group, polyether's concentration, organic solvent, negative ion of lithium salt and lithium salt's concentration, are discussed and reported

  3. Synergistic extraction of Gd3+ by ternary system of AAB species composed of HBMBP-P507-TBP in toluene

    International Nuclear Information System (INIS)

    Chen Dingfang; Lu Xiuzhen; Peng Lie; Wang Wenqing

    1990-01-01

    Trivalent lanthanide systems have been shown to exhibit variable coordination number ranging from 6 to 12 with which 7 and 8 are a common sight. Those ions which have the coordination number twice as large as the number of valence electrons may easily produce synergic effect. In order to prove the regularity of synergistic extraction and the exploration of new ternary synergic system proposed by Xu Guangxian and to search a new solvent extract system for separating the lanthanide elements, the synergic extraction of Cd 3+ from perchloric acid solution by HBMBP P507-TBP in toluene was studied. The system is composed of two chelate extracting ligands and one neutral extractants, namely AAB species. The equilibrium constants were determined to be logβ 1 = -4.24 (HPMBP system, extracted complex Gd(PMBP) 3 ); logβ * 1 = -2.88 (extracted complex Gd(PMBP) 3 (HPMBP)); logβ 12 = -1.04 (HPMBP-P507 system, synergic complex Gd(HA 2 )(PMBP) 2 ); logβ 13 = -0.316 (HPMBP-TBP system, synergic complex Gd(HMBP) 3 TBP); logβ * 13 = 1.87 (synergic complex Gd(PMBP) 3 2TBP); logβ 123 = 1.04 (HPMBP-P507-TBP system, ternary synergic complex Gd(HA 2 )(PMBP) 2 TBP) respectively. According to Xu Guangxian's opinion, the synergistic effect of chelate, neutral complex in ternary system arises from satisfying the electricity neutrality principle, loss-of-hydrophilic principle and coordinate substitution principle. From the structure of ternary extraction compound, it is shown that the existence of the different size molecules of P507 and PMBP increases the unsymmetry of coordinate ions. Perhaps that is the reason to produce an obvious ternary synergic effect

  4. KneeTex: an ontology-driven system for information extraction from MRI reports.

    Science.gov (United States)

    Spasić, Irena; Zhao, Bo; Jones, Christopher B; Button, Kate

    2015-01-01

    In the realm of knee pathology, magnetic resonance imaging (MRI) has the advantage of visualising all structures within the knee joint, which makes it a valuable tool for increasing diagnostic accuracy and planning surgical treatments. Therefore, clinical narratives found in MRI reports convey valuable diagnostic information. A range of studies have proven the feasibility of natural language processing for information extraction from clinical narratives. However, no study focused specifically on MRI reports in relation to knee pathology, possibly due to the complexity of knee anatomy and a wide range of conditions that may be associated with different anatomical entities. In this paper we describe KneeTex, an information extraction system that operates in this domain. As an ontology-driven information extraction system, KneeTex makes active use of an ontology to strongly guide and constrain text analysis. We used automatic term recognition to facilitate the development of a domain-specific ontology with sufficient detail and coverage for text mining applications. In combination with the ontology, high regularity of the sublanguage used in knee MRI reports allowed us to model its processing by a set of sophisticated lexico-semantic rules with minimal syntactic analysis. The main processing steps involve named entity recognition combined with coordination, enumeration, ambiguity and co-reference resolution, followed by text segmentation. Ontology-based semantic typing is then used to drive the template filling process. We adopted an existing ontology, TRAK (Taxonomy for RehAbilitation of Knee conditions), for use within KneeTex. The original TRAK ontology expanded from 1,292 concepts, 1,720 synonyms and 518 relationship instances to 1,621 concepts, 2,550 synonyms and 560 relationship instances. This provided KneeTex with a very fine-grained lexico-semantic knowledge base, which is highly attuned to the given sublanguage. Information extraction results were evaluated

  5. Micro-Sample Extraction System for In-Situ Missions to Planets, Planetary Satellites, and Primitive Bodies

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop a proof-of-concept Micro-Sample Extraction System (µSES) to enable microfluidic instruments, currently under development at NASA Goddard Space...

  6. Influence of the extraction procedure on the antioxidative activity of lentil seed extracts in a β-carotene-linoleate model system

    Directory of Open Access Journals (Sweden)

    Chavan, U.

    2001-04-01

    Full Text Available Phenolic compounds were extracted from lentil seeds using three solvent systems: 80% (v/v acetone, 80% (v/v methanol, and 80% (v/v ethanol. Each extract was subsequently separated into two fractions by chromatoghraphy on a column with Toyo Pearl HW-40 using water (fraction I and methanol (fraction II for elution. Antioxidative activity of extracts and their respective fractions were examined in a β-carotene-linoleate model system. All three extracts exhibited similar antioxidant activity. Considering the level of phenolic compounds in extracts it seems that phenolic compounds from the acetone extract were less active than those from either the methanolic and ethanolic ones. Because the content of phenolics was about 16-fold lower in fraction I of the methanolic and ethanolic extracts compared to fraction II, the phenolics in fraction I of the methanol and ethanol extracts from lentil seeds are much more active than these in fraction II. A stronger antioxidant activity of fraction I from the acetone extract compared to the crude acetone extract was observed during the latter incubation stage. The reason was a relatively high level of phenolic compounds in this fraction. UV spectra confirmed that the phenolic compounds from the acetone extract were different compared to methanolic and ethanolic extracts.Los compuestos fenólicos fueron extraídos de semillas de lenteja usando tres sistemas de disolventes: acetona del 80% (v/v, metanol del 80% (v/v, y etanol del 80% (v/v. Cada extracto fue separado posteriormente en dos fracciones por cromatografía en columna con Toyo Pearl HW-40 usando agua (fracción I y metanol (fracción II para la elución. La actividad antioxidante de los extractos y de sus fracciones respectivas fueron examinadas en un sistema modelo β-caroteno-linoleato. Los tres extractos exhibieron actividad antioxidante similar. Atendiendo al nivel de compuestos fenólicos en los extractos parece que los compuestos del extracto

  7. Flow system for optical activity detection of vegetable extracts employing molecular exclusion continuous chromatographic detection

    Science.gov (United States)

    Fajer, V.; Rodríguez, C.; Naranjo, S.; Mesa, G.; Mora, W.; Arista, E.; Cepero, T.; Fernández, H.

    2006-02-01

    The combination of molecular exclusion chromatography and laser polarimetric detection has turned into a carbohydrate separation and quantification system for plant fluids of industrial value, making it possible the evaluation of the quality of sugarcane juices, agave juices and many other plant extracts. Some previous papers described a system where liquid chromatography separation and polarimetric detection using a LASERPOL 101M polarimeter with He-Ne light source allowed the collection and quantification of discrete samples for analytical purposes. In this paper, the authors are introducing a new improved system which accomplishes polarimetric measurements in a continuous flux. Chromatograms of several carbohydrates standard solutions were obtained as useful references to study juice quality of several sugarcane varieties under different physiological conditions. Results by either discrete or continuous flux systems were compared in order to test the validation of the new system. An application of the system to the diagnostics of scalded foliar is described. A computer program allowing the output of the chromatograms to a display on line and the possibility of digital storing, maxima detections, zone integration, and some other possibilities make this system very competitive and self-convincing.

  8. Permit to Work System Conformity Analysis based on the System Standard Criteria in an Oil and Gas Extraction Company

    Directory of Open Access Journals (Sweden)

    A. Ghahramani

    2007-04-01

    Full Text Available Background and Aims   Permit to work (PTW system as an operational control methods, is an accepted system for control of maintenance activities hazards in chemical industries. The main objective of this study was degree of conformity analysis between existing situation of PTW system and audit criteria.     Methods   In this cross - sectional study, PTW system was audited in an oil and gas extracting   industry by checklist.     Results   Major nonconformities include outdating of system legal and regulation, non existence of permit for majority of dangerous activities, unidentified training needs, incomplete  identification and risk assessment of maintenance hazards before doing them, unspecified   inspection and survey frequencies during works and nonexistence of scheduled auditing for the system.     Conclusion   PTW audit results showed that there is a noticeable gap between audit criteria and  audit evidences. So that the examined system had nonconformities in all of the checklist sections; system, training and competency, permit, coordination and monitoring.  

  9. A novel technique to extract events from access control system and locate persons

    International Nuclear Information System (INIS)

    Vincent, M.; Vaidyanathan, Mythili; Patidar, Suresh Chandra; Prabhakara Rao, G.

    2011-01-01

    Indira Gandhi Centre for Atomic Research houses many laboratories which handle radioactive materials and classified materials. Protection and accounting of men and material and critical facilities are important aspect of nuclear security. Access Control System (ACS) is used to enhance the protective measures against elevated threat environment. Access control system hardware consists of hand geometry readers, RFID readers, Controllers, Electromagnetic door locks, Turnstiles, fiber cable laying and termination etc. Access Control System controls and monitors the people accessing the secured facilities. Access Control System generates events on: 1. Showing of RFID card, 2. Rotation of turnstile, 3. Download of valid card numbers, 4. Generation of alarms etc. Access control system turnstiles are located in main entrance of a facility, entrance of inside laboratory and door locks are fixed on secured facilities. Events are stored in SQL server database. From the events stored in database a novel technique is developed to extract events and list the persons in a particular facility, list all entry/exit events on one day, list the first in and last out entries. This paper discusses the complex multi level group by queries and software developed to extract events from database, locate persons and generate reports. Software is developed as a web application in ASP.Net and query is written in SQL. User can select the doors, type of events and generate reports. Reports are generated using the master data stored about employees RFID cards and events data stored in tables. Four types of reports are generated 1. Plant Emergency Report, 2. Locate User Report, 3. Entry - Exit Report, 4. First in Last out Report. To generate plant emergency report for whole plant only events generated in outer gates have to be considered. To generate plant emergency report for inside laboratory, events generated in entrance gates have to be ignored. (author)

  10. Performance of multi-aperture grid extraction systems for an ITER-relevant RF-driven negative hydrogen ion source

    Science.gov (United States)

    Franzen, P.; Gutser, R.; Fantz, U.; Kraus, W.; Falter, H.; Fröschle, M.; Heinemann, B.; McNeely, P.; Nocentini, R.; Riedl, R.; Stäbler, A.; Wünderlich, D.

    2011-07-01

    The ITER neutral beam system requires a negative hydrogen ion beam of 48 A with an energy of 0.87 MeV, and a negative deuterium beam of 40 A with an energy of 1 MeV. The beam is extracted from a large ion source of dimension 1.9 × 0.9 m2 by an acceleration system consisting of seven grids with 1280 apertures each. Currently, apertures with a diameter of 14 mm in the first grid are foreseen. In 2007, the IPP RF source was chosen as the ITER reference source due to its reduced maintenance compared with arc-driven sources and the successful development at the BATMAN test facility of being equipped with the small IPP prototype RF source ( {\\sim}\\frac{1}{8} of the area of the ITER NBI source). These results, however, were obtained with an extraction system with 8 mm diameter apertures. This paper reports on the comparison of the source performance at BATMAN of an ITER-relevant extraction system equipped with chamfered apertures with a 14 mm diameter and 8 mm diameter aperture extraction system. The most important result is that there is almost no difference in the achieved current density—being consistent with ion trajectory calculations—and the amount of co-extracted electrons. Furthermore, some aspects of the beam optics of both extraction systems are discussed.

  11. Fetal ECG extraction via Type-2 adaptive neuro-fuzzy inference systems.

    Science.gov (United States)

    Ahmadieh, Hajar; Asl, Babak Mohammadzadeh

    2017-04-01

    We proposed a noninvasive method for separating the fetal ECG (FECG) from maternal ECG (MECG) by using Type-2 adaptive neuro-fuzzy inference systems. The method can extract FECG components from abdominal signal by using one abdominal channel, including maternal and fetal cardiac signals and other environmental noise signals, and one chest channel. The proposed algorithm detects the nonlinear dynamics of the mother's body. So, the components of the MECG are estimated from the abdominal signal. By subtracting estimated mother cardiac signal from abdominal signal, fetal cardiac signal can be extracted. This algorithm was applied on synthetic ECG signals generated based on the models developed by McSharry et al. and Behar et al. and also on DaISy real database. In environments with high uncertainty, our method performs better than the Type-1 fuzzy method. Specifically, in evaluation of the algorithm with the synthetic data based on McSharry model, for input signals with SNR of -5dB, the SNR of the extracted FECG was improved by 38.38% in comparison with the Type-1 fuzzy method. Also, the results show that increasing the uncertainty or decreasing the input SNR leads to increasing the percentage of the improvement in SNR of the extracted FECG. For instance, when the SNR of the input signal decreases to -30dB, our proposed algorithm improves the SNR of the extracted FECG by 71.06% with respect to the Type-1 fuzzy method. The same results were obtained on synthetic data based on Behar model. Our results on real database reflect the success of the proposed method to separate the maternal and fetal heart signals even if their waves overlap in time. Moreover, the proposed algorithm was applied to the simulated fetal ECG with ectopic beats and achieved good results in separating FECG from MECG. The results show the superiority of the proposed Type-2 neuro-fuzzy inference method over the Type-1 neuro-fuzzy inference and the polynomial networks methods, which is due to its

  12. Simultaneous Extraction, Enrichment and Removal of Dyes from Aqueous Solutions Using a Magnetic Aqueous Micellar Two-Phase System

    Directory of Open Access Journals (Sweden)

    Shuanggen Wu

    2017-12-01

    Full Text Available The magnetic aqueous micellar two-phase system (MAMTPS has the advantages combined of magnetic solid phase extraction (MSPE and aqueous micellar two-phase system (AMTPS. Thus, MAMTPS based on Fe3O4 magnetic nanoparticles (MNPs and a nonionic surfactant Triton X-114 (TX-114 was developed for the extraction, enrichment and removal of three dyes (Congo red, methyl blue, and methyl violet from aqueous solutions in this study. The MNPs Fe3O4@NH2 was screened as the optimal MNPs benefiting the extraction. Then, the influencing factors of MNPs amount, TX-114 concentration, vibration time, and extraction temperature were investigated in detail. The results showed that the extraction efficiencies of three dyes almost reached 100% using MAMTPS under the optimal conditions; MAMTPS had higher extraction ability than the individual MSPE or AMTPS. Thus, MAMTPS had the advantages of simple operation, high extraction ability, easy recycling of MNPs, and short phase-separation time, which showspotential for use in the extraction and analysis of contaminants from water samples.

  13. Extraction of Salinity-Gradient Energy by a Hybrid Capacitive-Mixing System.

    Science.gov (United States)

    Lee, Jiho; Yoon, Hongsik; Lee, Jaehan; Kim, Taeyoung; Yoon, Jeyong

    2017-04-10

    Salinity-gradient energy (SGE) is a renewable energy source available wherever two solutions with different salinity mix. Capacitive-mixing (Capmix) is a technology that directly extracts the SG potential through the movements of ions in high- and low-concentration solutions. However, the energy-harvesting performance of Capmix needs further improvement. Herein, a hybrid Capmix that consists of a battery and capacitive electrodes is proposed. In this system, sodium ions and anions are captured/released by the metal oxide and carbon electrodes, respectively. The hybrid Capmix extracted an energy density that was approximately three times higher (130 J m -2 ) and exhibited a notable power output (97 mW m -2 ) compared to the previous Capmix using ion-exchange membranes. Furthermore, the hybrid system operated successfully with real river water and seawater. These results suggest that the hybrid Capmix could be a viable option to harvest energy from salinity gradients. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Separation and concentration of uranium by extraction chromatography : U(VI) - H3PO4 system

    International Nuclear Information System (INIS)

    Nobre, J.S.M.

    1981-01-01

    The feasibility of using the extraction chromatographic technique as a way to recover uranium from phosphatic rocks evaluated. The behaviour of uranium from raw phsophoric acid solutions in chromatographic systems using the mixture di(2-ethylhexyl) orthophosphoric acid (D2EHPA) - tributyl phosphate (TBP) as the stationary phase was studied. Materials as alumina, activated carbon and the macroporous resins XAD-4 and XAD-7 were used as supports for organic stationary phase. The best results were obtained with poliacrilic polymer XAD-7, due to its excellent chromatographic properties and efficient organic phase retention. Uranium was quantitatively retained by D2EHPA-TBP-XAD-7 columns from synthetic phosphoric acid solutions with typical composition of phosphatic acid liquors. The elution of uranium from this system was also studied, and the best results were obtained with phosphoric acid solutions. This chromatographic column presented a high stability, not changing their properties even after more than twenty cycles, including the conditioning, sorption, wasking and elution steps. Uranium determinations were perfpormed by indirect titration with potassium dichromate and by molecular absorption spectrophotometry with hydrogen peroxide- carbonate. A new and more sensitive method for uranium determination in phosphoric medium, which might be applied to acid liquors of phosphatic ores, was developed. An extraction-photometric method was used, with Arsenazo III (1,8-dihydroxynaphtalene-3,6-disulphonic acid-2,7-bis(azo-2)-phenylarsonic acid) as the reagent for uranium. (Author) [pt

  15. The Combination of GIS and Biphasic to Better Predict In Vivo Dissolution of BCS Class IIb Drugs, Ketoconazole and Raloxifene.

    Science.gov (United States)

    Tsume, Yasuhiro; Igawa, Naoto; Drelich, Adam J; Amidon, Gregory E; Amidon, Gordon L

    2018-01-01

    The formulation developments and the in vivo assessment of Biopharmaceutical Classification System (BCS) class II drugs are challenging due to their low solubility and high permeability in the human gastrointestinal (GI) tract. Since the GI environment influences the drug dissolution of BCS class II drugs, the human GI characteristics should be incorporated into the in vitro dissolution system to predict bioperformance of BCS class II drugs. An absorptive compartment may be important in dissolution apparatus for BCS class II drugs, especially for bases (BCS IIb) because of high permeability, precipitation, and supersaturation. Thus, the in vitro dissolution system with an absorptive compartment may help predicting the in vivo phenomena of BCS class II drugs better than compendial dissolution apparatuses. In this study, an absorptive compartment (a biphasic device) was introduced to a gastrointestinal simulator. This addition was evaluated if this in vitro system could improve the prediction of in vivo dissolution for BCS class IIb drugs, ketoconazole and raloxifene, and subsequent absorption. The gastrointestinal simulator is a practical in vivo predictive tool and exhibited an improved in vivo prediction utilizing the biphasic format and thus a better tool for evaluating the bioperformance of BCS class IIb drugs than compendial apparatuses. Copyright © 2018. Published by Elsevier Inc.

  16. Bi-phasic growth of Listeria monocytogenes in chemically defined medium at low temperatures.

    Science.gov (United States)

    Tyrovouzis, Nikolaos A; Angelidis, Apostolos S; Stoforos, Nikolaos G

    2014-09-01

    The present work reports a novel observation regarding the growth of L. monocytogenes in modified Welshimer's broth (MWB) at low temperatures. Specifically, the direct monitoring of the growth of L. monocytogenes Scott A using plate count data revealed that the pathogen displays a bi-phasic growth pattern in MWB at 7 °C. This bi-phasic growth pattern is masked (not observed) when optical density (OD) measurements are used to monitor growth due to the inability of OD readings to detect L. monocytogenes population density increases up to 10(7) CFU/mL. This bi-phasic growth phenomenon was further investigated as a function of growth temperature (4 °C, 7 °C, 10 °C, 14 °C and 18 °C), medium composition (by altering the MWB composition by ten-fold increases in different sets of medium constituents), inoculum level (10(2), 10(3), 10(4), 10(5), 10(6), and 10(7) CFU/mL) and L. monocytogenes strain (10 strains). The growth of L. monocytogenes Scott A in MWB at 7 °C, 10 °C and 14 °C was consistently bi-phasic and independent of growth rate; at 18 °C, growth was consistently mono-phasic (single-phase, typical sigmoid growth curves), whereas no growth was observed at 4 °C. The tested modifications in the composition of MWB did not influence the bi-phasic nature of L. monocytogenes Scott A growth at 7 °C, and, overall, we could not point out any strain-, or serotype-specific effects. On the other hand, the initial inoculum level appears to affect the form of the growth curve, as there was a shift towards mono-phasic growth in trials with increasing initial inocula. A mathematical model, based on a stepwise response and described through two sequential sigmoid curves, was used to describe bi-phasic growth and estimate the kinetic parameters of L. monocytogenes growth. An alternative hypothesis, based on the assumption of the existence of two subpopulations, possessing different growth kinetics, materialized under the stress imposed on L. monocytogenes cells due to the

  17. Ventilator Data Extraction with a Video Display Image Capture and Processing System.

    Science.gov (United States)

    Wax, David B; Hill, Bryan; Levin, Matthew A

    2017-06-01

    Medical hardware and software device interoperability standards are not uniform. The result of this lack of standardization is that information available on clinical devices may not be readily or freely available for import into other systems for research, decision support, or other purposes. We developed a novel system to import discrete data from an anesthesia machine ventilator by capturing images of the graphical display screen and using image processing to extract the data with off-the-shelf hardware and open-source software. We were able to successfully capture and verify live ventilator data from anesthesia machines in multiple operating rooms and store the discrete data in a relational database at a substantially lower cost than vendor-sourced solutions.

  18. Extraction of Structural System Matrices from AN Identified State-Space System Using the Combined Measurements of Dva

    Science.gov (United States)

    KO, W. J.; HUNG, C. F.

    2002-01-01

    A time domain method for the extraction of the structural system matrices (mass, damping and stiffness matrices) from an identified state-space system is proposed in this paper using the combined measurements of displacement, velocity and acceleration (DVA) together with the input excitations. The method is based on the invariance of continuous-time Markov parameters. An explicit expression of the relationship between the continuous-time Markov parameters, the structural system matrices, and the influence matrices for output DVA as well as the input force has been derived. The determination of structural system matrices is also valid when only the displacement, velocity or acceleration responses are measured. In this paper, the equivalent state system matrices are obtained by an algorithm, which combines the eigensystem realization algorithm (ERA) and the autoregressive with exogeneous (ARX) model. The ARX model provides the necessary discrete-time Markov parameters from the measured input and output data, and then the equivalent state system matrices are identified from discrete-time Markov parameters by using the ERA. A lumped mass model with three degrees of freedom is employed to illustrate the accuracy and feasibility of the presented method.

  19. A Spatial Division Clustering Method and Low Dimensional Feature Extraction Technique Based Indoor Positioning System

    Directory of Open Access Journals (Sweden)

    Yun Mo

    2014-01-01

    Full Text Available Indoor positioning systems based on the fingerprint method are widely used due to the large number of existing devices with a wide range of coverage. However, extensive positioning regions with a massive fingerprint database may cause high computational complexity and error margins, therefore clustering methods are widely applied as a solution. However, traditional clustering methods in positioning systems can only measure the similarity of the Received Signal Strength without being concerned with the continuity of physical coordinates. Besides, outage of access points could result in asymmetric matching problems which severely affect the fine positioning procedure. To solve these issues, in this paper we propose a positioning system based on the Spatial Division Clustering (SDC method for clustering the fingerprint dataset subject to physical distance constraints. With the Genetic Algorithm and Support Vector Machine techniques, SDC can achieve higher coarse positioning accuracy than traditional clustering algorithms. In terms of fine localization, based on the Kernel Principal Component Analysis method, the proposed positioning system outperforms its counterparts based on other feature extraction methods in low dimensionality. Apart from balancing online matching computational burden, the new positioning system exhibits advantageous performance on radio map clustering, and also shows better robustness and adaptability in the asymmetric matching problem aspect.

  20. Intensification of separation of extraction emulsions in systems with tributyl phosphate in ultrasonic field

    International Nuclear Information System (INIS)

    Khavskij, N.N.; Kagerman'yan, V.S.; Kanevskij, I.N.; Kim, S.P.

    1976-01-01

    The fundamental principles have been studied determining the separation of extraction emulsions appearing in the course of the aqueous and ammonia reextraction of molybdenum from tributylphosphate (TBP) in the ultrasonic field. Piezoelectric radiators with a frequency of 0.8 to 1,0 MHz are used as ultrasonic generators. The organic extract contains 7 g/1 Mo within the hydrosolvate complex. Acceleration of the separation process has been established to take place in the ultrasound region 0.25 to 1.25 W/cm 2 for the aqueous and ammonia systems. The optimal conditions for the separation process exist within 0.5 to 0.65 W/cm 2 , they being 18 minutes for the aqueous and 16 minutes for the ammonia emulsion. It is demonstrated that as a result of the superposition of the ultrasound over the emulsions being formed by TBP with water and ammonia, the separation of the aqueous emulsions increases by a factor of 5 to 6 and of the ammonia emulsions - by a factor of 50 to 80. It is advisable that the ultrasound emulsion treatment for 5 to 10 minutes be coupled with a subsequent settling. As this takes place, the total period of the phase separation will be 18 to 20 minutes. The separation rate increases with temperature. The maximum emulsion separation acceleration is observed within 25 to 30 deg C. The possibility has been revealed to realize the process of the ultrasound intensification of the emulsion separation process by using small-sized extraction equipment

  1. Comparison of solvent/derivatization agent systems for determination of extractable toluene diisocyanate from flexible polyurethane foam.

    Science.gov (United States)

    Vangronsveld, Erik; Berckmans, Steven; Spence, Mark

    2013-06-01

    Flexible polyurethane foam (FPF) is produced from the reaction of toluene diisocyanate (TDI) and polyols. Limited and conflicting results exist in the literature concerning the presence of unreacted TDI remaining in FPF as determined by various solvent extraction and analysis techniques. This study reports investigations into the effect of several solvent/derivatization agent combinations on extractable TDI results and suggests a preferred method. The suggested preferred method employs a syringe-based multiple extraction of foam samples with a toluene solution of 1-(2-methoxyphenyl)-piperazine. Extracts are analyzed by liquid chromatography using an ion trap mass spectrometry detection technique. Detection limits of the method are ~10ng TDI g(-1) foam (10 ppb, w/w) for each TDI isomer (i.e. 2,4-TDI and 2,6-TDI). The method was evaluated by a three-laboratory interlaboratory comparison using two representative foam samples. The total extractable TDI results found by the three labs for the two foams were in good agreement (relative standard deviation of the mean of 30-40%). The method has utility as a basis for comparing FPFs, but the interpretation of extractable TDI results using any solvent as the true value for 'free' or 'unreacted' TDI in the foam is problematic, as demonstrated by the difference in the extracted TDI results from the different extraction systems studied. Further, a consideration of polyurethane foam chemistry raises the possibility that extractable TDI may result from decomposition of parts of the foam structure (e.g. dimers, biurets, and allophanates) by the extraction system.

  2. Effect of concentration of the height of a transfer unit in a liquid/liquid solvent-extraction system

    International Nuclear Information System (INIS)

    Chamberlain, D.B.

    1981-05-01

    Pulsed, sieve-plate extraction columns were used to examine the effect of solute concentration on extraction efficiency. Cerium was extracted from an aqueous coprocessing solution, simulating reprocessing wastes produced at the Idaho Chemical Processing Plant. The organic extractant used in this process was dihexyl-N, N-diethylcarbamylmethylene phosphonate. Subsequently, cerium was stripped from the organic phase with 0.05 M nitric acid. The Heights of a Transfer Unit were calculated from the extraction and stripping column operating data. Both interstage and overall transfer units were calculated. Nine extraction and nine stripping tests were performed. Three extraction feed concentrations, each repeated at three different pulse frequencies were used to study the affect of concentration on height of a transfer unit. The stripping column was operated simultaneously with the extraction column. Both columns were operated at pulse amplitudes of 2.5 cm. Data based upon the overall extraction column showed a slight decrease in the height of a transfer unit as the solute concentration decreased. Based upon the overall stripping column data, a decrease in solute concentration resulted in a very slight increase in the height of a transfer unit. However, interstage transfer unit calculations for both columns indicated solute concentration had no significant effect on the height of a transfer unit. Based on the experimental tests, it was concluded that solute concentration caused only slight changes in extraction efficiency for the concentration range studied. Other factors such as pulse frequency, aqueous/organic flow ratio, and possibly the dispersed phase bubble size had a much greater effect on the extraction efficiency for the system studied

  3. Extraction and separation of tungsten (VI) from aqueous media with Triton X-100-ammonium sulfate-water aqueous two-phase system without any extractant.

    Science.gov (United States)

    Yongqiang Zhang; Tichang Sun; Tieqiang Lu; Chunhuan Yan

    2016-11-25

    An aqueous two-phase system composed of Triton X-100-(NH 4 ) 2 SO 4 -H 2 O was proposed for extraction and separation of tungsten(VI) from aqueous solution without using any extractant. The effects of aqueous pH, concentration of ammonium sulfate, Triton X-100 and tungsten, extracting temperature on the extraction of tungsten were investigated. The extraction of tungsten has remarkable relationship with aqueous pH and are to above 90% at pH=1.0-3.0 under studied pH range (pH=1.0-7.0) and increases gradually with increasing Triton X-100 concentration, but decreases slightly with increasing ammonium sulfate concentration. The extraction percentage of tungsten is hardly relevant to temperature but its distribution coefficient linearly increases with increasing temperature within 303.15-343.15K. The distribution coefficient of tungsten increases with the increase of initial tungsten concentration (0.1-3%) and temperature (303.15 K-333.15K). The solubilization capacity of tungsten in Triton X-100 micellar phase is independent of temperature. FT-IR analysis reveals that there is no evident interaction between polytungstate anion and ether oxygen unit in Triton X-100, and DLS analysis indicates that zeta potential of Triton X-100 micellar phase have a little change from positive to negative after extracting tungsten. Based on the above-mentioned results, it can be deduced that polytungstate anions are solubilized in hydrophilic outer shell of Triton X-100 micelles by electrostatic attraction depending on its relatively high hydrophobic nature. The stripping of tungsten is mainly influenced by temperature and can be easily achieved to 95% in single stage stripping. The tungsten (VI) is separated out from solution containing Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Al(III), Cr(III) and Mn(II) under the suitable conditions. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. Multicompartment retinal ganglion cells response to high frequency bi-phasic pulse train stimulation: Simulation results.

    Science.gov (United States)

    Maturana, Matias I; Grayden, David B; Burkitt, Anthony N; Meffin, Hamish; Kameneva, Tatiana

    2013-01-01

    Retinal ganglion cells (RGCs) are the sole output neurons of the retina that carry information about a visual scene to the brain. By stimulating RGCs with electrical stimulation, it is possible to elicit a sensation of light for people with macular degeneration or retinitis pigmentosa. To investigate the responses of RGCs to high frequency bi-phasic pulse train stimulation, we use previously constrained models of multi-compartment OFF RGCs. The morphologies of mouse RGCs are taken from the Chalupa set of the NeuroMorpho database. The cell models are divided into compartments representing the dendrites, soma and axon that vary between the cells. A total of 132 cells are simulated in the NEURON environment. Results show that the cell morphology plays an important role in the response characteristics of the cell to high frequency bi-phasic pulse train stimulation.

  5. Validation of a heterogeneous elastic-biphasic model for the numerical simulation of the PDL.

    Science.gov (United States)

    Favino, Marco; Gross, Christian; Drolshagen, Marcel; Keilig, Ludger; Deschner, James; Bourauel, Christoph; Krause, Rolf

    2013-01-01

    An elastic-biphasic model for the simulation of the periodontal ligament (PDL) and the adjacent tooth is presented and investigated. The PDL is modelled as a biphasic material following the work of Ehlers and Markert (2001 ), whereas the tooth is modelled as a linear elastic body. A spatial discretisation scheme is proposed based on mixed finite elements for the spatial discretisation. Due to nonlinearity in the model, a predictor-corrector scheme is employed as a temporal discretisation scheme. In order to validate the PDL model, in vitro measurements are compared with numerical simulations. The numerical simulations are performed using geometries resulting from micro-CT scanner of the same porcine tooth, which was employed for the in vitro measurements.

  6. Biphasic and boundary lubrication mechanisms in artificial hydrogel cartilage: A review.

    Science.gov (United States)

    Murakami, Teruo; Yarimitsu, Seido; Nakashima, Kazuhiro; Sakai, Nobuo; Yamaguchi, Tetsuo; Sawae, Yoshinori; Suzuki, Atsushi

    2015-12-01

    Various studies on the application of artificial hydrogel cartilage to cartilage substitutes and artificial joints have been conducted. It is expected in clinical application of artificial hydrogel cartilage that not only soft-elastohydrodynamic lubrication but biphasic, hydration, gel-film and boundary lubrication mechanisms will be effective to sustain extremely low friction and minimal wear in daily activities similar to healthy natural synovial joints with adaptive multimode lubrication. In this review article, the effectiveness of biphasic lubrication and boundary lubrication in hydrogels in thin film condition is focused in relation to the structures and properties of hydrogels. As examples, the tribological behaviors in three kinds of poly(vinyl alcohol) hydrogels with high water content are compared, and the importance of lubrication mechanism in biomimetic artificial hydrogel cartilage is discussed to extend the durability of cartilage substitute. © IMechE 2015.

  7. Efficacy and safety of biphasic insulin aspart and biphasic insulin lispro mix in patients with type 2 diabetes: A review of the literature

    Directory of Open Access Journals (Sweden)

    Ajay Kumar

    2016-01-01

    Full Text Available Type 2 diabetes (T2D represents an escalating burden worldwide, particularly in China and India. Compared with Caucasians, Asian people with diabetes have lower body mass index, increased visceral adiposity, and postprandial glucose (PPG/insulin resistance. Since postprandial hyperglycemia contributes significantly to total glycemic burden and is associated with heightened cardiovascular risk, targeting PPG early in T2D is paramount. Premixed insulin regimens are widely used in Asia due to their convenience and effectiveness. Data from randomized controlled trials and observational studies comparing efficacy and safety of biphasic insulin aspart 30 (BIAsp 30 with biphasic insulin lispro mix (LM 25/50 and versus other insulin therapies or oral antidiabetic drugs (OADs in T2D demonstrated that BIAsp 30 and LM 25/50 were associated with similar or greater improvements in glycemic control versus comparator regimens, such as basal–bolus insulin, in insulin-naÏve, and prior insulin users. Studies directly comparing BIAsp 30 and LM 25 provided conflicting glycemic control results. Safety data generally showed increased hypoglycemia and weight gain with premixed insulins versus basal–bolus insulin or OADs. However, large observational trials documented improvements in glycated hemoglobin, PPG, and hypoglycemia with BIAsp 30 in multi-ethnic patient populations. In summary, this literature review demonstrates that premixed insulin regimens are an appropriate and effective treatment choice in T2D.

  8. A total analytical system featuring a novel solid-liquid extraction chamber for solid sample flow analysis.

    Science.gov (United States)

    Galvis-Sánchez, Andrea C; Santos, João Rodrigo; Rangel, António O S S

    2016-11-01

    In this work, a total flow analysis system based on a novel solid-liquid extraction chamber is presented. This strategy enables all the main experimental procedures for the analysis of a solid sample to be performed automatically: enrichment of the liquid extract, sample treatment, filtration of the liquid extract from the solid sample, directing the extract towards detection, and finally cleansing of the chamber for the following solid sample to be analyzed. The chamber designed to be incorporated in the flow manifold presents two main features: it accommodates stirring bars for enhancing the extraction process, and it presents replaceable solid sample containers (a spare part of the solid-liquid extraction chamber) to easily replace the solid sample and therefore enhance sample analysis throughput. The chamber performance was assessed using two different solid samples, an ion exchanger resin and vegetable samples, focussing on proton and nitrate ion extraction, respectively. The main figures of merit achieved were relative standard deviation (RSD) and relative error values below 7 % for all determinations. The determination rate for vegetable samples was ca. 12 samples h -1 . The proposed strategy may be exploited to perform automatically the analysis of solid samples as it embodies a simple automatic strategy of a very important but time-consuming and laborious analytical operation. Graphical abstract TAS for solid liquid extraction and nitrate potentiometric determination of vegetable samples.

  9. Sliding Window Based Feature Extraction and Traffic Clustering for Green Mobile Cyberphysical Systems

    Directory of Open Access Journals (Sweden)

    Jiao Zhang

    2017-01-01

    Full Text Available Both the densification of small base stations and the diversity of user activities bring huge challenges for today’s heterogeneous networks, either heavy burdens on base stations or serious energy waste. In order to ensure coverage of the network while reducing the total energy consumption, we adopt a green mobile cyberphysical system (MCPS to handle this problem. In this paper, we propose a feature extraction method using sliding window to extract the distribution feature of mobile user equipment (UE, and a case study is presented to demonstrate that the method is efficacious in reserving the clustering distribution feature. Furthermore, we present traffic clustering analysis to categorize collected traffic distribution samples into a limited set of traffic patterns, where the patterns and corresponding optimized control strategies are used to similar traffic distributions for the rapid control of base station state. Experimental results show that the sliding window is more superior in enabling higher UE coverage over the grid method. Besides, the optimized control strategy obtained from the traffic pattern is capable of achieving a high coverage that can well serve over 98% of all mobile UE for similar traffic distributions.

  10. Evaluation of a preservative system in a gel containing hydroalcoholic extract of Schinus terebinthifolius

    Directory of Open Access Journals (Sweden)

    Túlio Flávio A. L. Moura

    2011-06-01

    Full Text Available Currently, microbial contamination is one of the major problems faced by the phytomedicine industry with respect to the quality of the raw materials. The objective of this study was to evaluate the effectiveness of a preservative system in a formulation with hydrogel containing hydroalcoholic extract of Schinus terebinthifolius Raddi, Anacardiaceae ("aroeira" or "Brazilian Peppertree", through the challenge test. The extracts were prepared by maceration at a ratio of 1:10 plant/solvent in 40% alcohol. Gel samples were artificially contaminated with separate inocula of Aspergillus niger, Candida albicans, Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa and the number of viable microorganisms determined in triplicate by the "pour plate" method for counting colonies at 0, 24 and 48h, 7, 14, 21 and 28 days. The addition of the preservatives (methyl and propylparaben in the "aroeira" gel proved to be effective against the studied species when the samples were evaluated using the challenge test. According to the criterion A of the European Pharmacopoeia, it was verified that the hydrogel product showed good conservation in a 28 days period.

  11. Extracting the orbital axis from gravitational waves of precessing binary systems

    Science.gov (United States)

    Kawaguchi, Kyohei; Kyutoku, Koutarou; Nakano, Hiroyuki; Shibata, Masaru

    2018-01-01

    We present a new method for extracting the instantaneous orbital axis only from gravitational wave strains of precessing binary systems observed from a particular observer direction. This method enables us to reconstruct the coprecessing frame waveforms only from observed strains for the ideal case with the high signal-to-noise ratio. Specifically, we do not presuppose any theoretical model of the precession dynamics and coprecessing waveforms in our method. We test and measure the accuracy of our method using the numerical relativity simulation data of precessing binary black holes taken from the SXS Catalog. We show that the direction of the orbital axis is extracted within ≈0.07 rad error from gravitational waves emitted during the inspiral phase. The coprecessing waveforms are also reconstructed with high accuracy; the mismatch (assuming white noise) between them and the original coprecessing waveforms is typically a few times 10-3 including the merger-ringdown phase, and can be improved by an order of magnitude focusing only on the inspiral waveform. In this method, the coprecessing frame waveforms are not only the purely technical tools for understanding the complex nature of precessing waveforms but also direct observables.

  12. Antimicrobial Activity of a Neem Cake Extract in a Broth Model Meat System

    Directory of Open Access Journals (Sweden)

    Marcello Nicoletti

    2013-08-01

    Full Text Available This work reports on the antimicrobial activity of an ethyl acetate extract of neem (Azadirachta indica cake (NCE against bacteria affecting the quality of retail fresh meat in a broth model meat system. NCE (100 µg was also tested by the agar disc diffusion method. It inhibited the growth of all tested microorganisms. The NCE growth inhibition zone (IZ ranged 11.33–22.67 mm while the ciprofloxacin (10 µg IZ ranged from 23.41–32.67 mm. There was no significant difference (p ≤ 0.05 between the antimicrobial activity of NCE and ciprofloxacin vs. C. jejuni and Leuconostoc spp. The NCE antibacterial activity was moreover determined at lower concentrations (1:10–1:100,000 in micro-assays. The percent growth reduction ranged from 61 ± 2.08–92 ± 3.21. The higher bacterial growth reduction was obtained at 10 µg concentration of NCE. Species-specific PCR and multiplex PCR with the DNA dye propidium monoazide were used to directly detect viable bacterial cells from experimentally contaminated meat samples. The numbers of bacterial cells never significantly (p ≤ 0.05 exceeded the inocula concentration used to experimentally contaminate the NCE treated meat. This report represents a screening methodology to evaluate the antimicrobial capability of a herbal extract to preserve meat.

  13. Antimicrobial activity of a neem cake extract in a broth model meat system.

    Science.gov (United States)

    Del Serrone, Paola; Nicoletti, Marcello

    2013-08-02

    This work reports on the antimicrobial activity of an ethyl acetate extract of neem (Azadirachta indica) cake (NCE) against bacteria affecting the quality of retail fresh meat in a broth model meat system. NCE (100 µg) was also tested by the agar disc diffusion method. It inhibited the growth of all tested microorganisms. The NCE growth inhibition zone (IZ) ranged 11.33-22.67 mm while the ciprofloxacin (10 µg) IZ ranged from 23.41-32.67 mm. There was no significant difference (p ≤ 0.05) between the antimicrobial activity of NCE and ciprofloxacin vs. C. jejuni and Leuconostoc spp. The NCE antibacterial activity was moreover determined at lower concentrations (1:10-1:100,000) in micro-assays. The percent growth reduction ranged from 61 ± 2.08-92 ± 3.21. The higher bacterial growth reduction was obtained at 10 µg concentration of NCE. Species-specific PCR and multiplex PCR with the DNA dye propidium monoazide were used to directly detect viable bacterial cells from experimentally contaminated meat samples. The numbers of bacterial cells never significantly (p ≤ 0.05) exceeded the inocula concentration used to experimentally contaminate the NCE treated meat. This report represents a screening methodology to evaluate the antimicrobial capability of a herbal extract to preserve meat.

  14. Preparation of highly infective Leishmania promastigotes by cultivation on SNB-9 biphasic medium

    Czech Academy of Sciences Publication Activity Database

    Grekov, Igor; Svobodová, M.; Nohýnková, E.; Lipoldová, Marie

    2011-01-01

    Roč. 87, č. 3 (2011), s. 273-277 ISSN 0167-7012 R&D Projects: GA MŠk(CZ) LC06009; GA ČR GA310/08/1697 Institutional research plan: CEZ:AV0Z50520514 Keywords : Leishmania * SNB-9 * biphasic culture medium * parasite infectivity Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 2.086, year: 2011

  15. Use of Respiratory Support in the Biphase Ventilation Airway Mode in the Newborn

    OpenAIRE

    S. N. Koval; A. Ye. Kulagin

    2006-01-01

    Biphasic positive airway pressure (BIPAP) (also known as DuoPAP, BiLevel, BiVent, PCV+, SPAP) is a mode of ventilation with cycling variations between two continuous positive airway pressure levels. It is a mixture of pressure controlled ventilation and spontaneous breathing, which is unrestricted in each phase of the respiratory cycle. The volume displacement caused by the difference between Phigh and Plow airway pressure level. The phase time ratio (PTR — the BIPAP frequency) is calculated ...

  16. A simulation study of the reaction of human heart to biphasic electrical shocks

    Directory of Open Access Journals (Sweden)

    Seemann Gunnar

    2004-06-01

    Full Text Available Abstract Background This article presents a study, which examines the effects of biphasic electrical shocks on human ventricular tissue. The effects of this type of shock are not yet fully understood. Animal experiments showed the superiority of biphasic shocks over monophasic ones in defibrillation. A mathematical computer simulation can increase the knowledge of human heart behavior. Methods The research presented in this article was done with different models representing a three-dimensional wedge of ventricular myocardium. The electrophysiology was described with Priebe-Beuckelmann model. The realistic fiber twist, which is specific to human myocardium was included. Planar electrodes were placed at the ends of the longest side of the virtual cardiac wedge, in a bath medium. They were sources of electrical shocks, which varied in magnitude from 0.1 to 5 V. In a second arrangement ring electrodes were placed directly on myocardium for getting a better view on secondary electrical sources. The electrical reaction of the tissue was generated with a bidomain model. Results The reaction of the tissue to the electrical shock was specific to the initial imposed characteristics. Depolarization appeared in the first 5 ms in different locations. A further study of the cardiac tissue behavior revealed, which features influence the response of the considered muscle. It was shown that the time needed by the tissue to be totally depolarized is much shorter when a biphasic shock is applied. Each simulation ended only after complete repolarization was achieved. This created the possibility of gathering information from all states corresponding to one cycle of the cardiac rhythm. Conclusions The differences between the reaction of the homogeneous tissue and a tissue, which contains cleavage planes, reveals important aspects of superiority of biphasic pulses. ...

  17. Study of hMSC proliferation and differentiation on Mg and Mg–Sr containing biphasic β-tricalcium phosphate and amorphous calcium phosphate ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Satish S., E-mail: sss42@pitt.edu [Department of Chemical & Petroleum Engineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Roy, Abhijit, E-mail: abr20@pitt.edu [Department of Bioengineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Lee, Boeun [Department of Bioengineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Kumta, Prashant N., E-mail: pkumta@pitt.edu [Department of Chemical & Petroleum Engineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Department of Bioengineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Center for Craniofacial Regeneration, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Department of Mechanical Engineering and Materials Science, University of Pittsburgh, PA 15261 (United States)

    2016-07-01

    Biphasic mixtures of either Mg{sup 2+} or combined Mg{sup 2+} and Sr{sup 2+} cation substituted β-tricalcium phosphate (β-TCP) and amorphous calcium phosphate (ACP) were prepared using a low temperature chemical phosphatizing and hydrolysis reaction approach. Scaffolds prepared using the cation substituted calcium phosphates were capable of supporting similar levels of human mesenchymal stem cell proliferation in comparison to commercially available β-TCP. The concentrations of Mg{sup 2+}, Sr{sup 2+}, and PO{sub 4}{sup 3−} released from these scaffolds were also within the ranges desired from previous reports to support both hMSC proliferation and osteogenic differentiation. Interestingly, hMSCs cultured directly on scaffolds prepared with only Mg{sup 2+} substituted β-TCP were capable of supporting statistically significantly increased alkaline phosphatase activity, osteopontin, and osteoprotegerin expression in comparison to all compositions containing both Mg{sup 2+} and Sr{sup 2+}, and commercially available β-TCP. hMSCs cultured in the presence of scaffold extracts also exhibited similar trends in the expression of osteogenic markers as was observed during direct culture. Therefore, it was concluded that the enhanced differentiation observed was due to the release of bioactive ions rather than the surface microstructure. The role of these ions on transforming growth factor-β and bone morphogenic protein signaling was also evaluated using a PCR array. It was concluded that the release of these ions may support enhanced differentiation through SMAD dependent TGF-β and BMP signaling. - Highlights: • Synthesis of Mg and Mg-Sr containing biphasic beta tricalcium phosphate ceramics • Magnesium substitution influences ALP activity compared to strontium content. • Solution extract plays a more dominant role on hMSC differentiation. • Direct and indirect Mg and Mg-Sr TCP culture show similar OPG and OPN expression.

  18. HIGH-PRECISION BIOLOGICAL EVENT EXTRACTION: EFFECTS OF SYSTEM AND OF DATA.

    Science.gov (United States)

    Cohen, K Bretonnel; Verspoor, Karin; Johnson, Helen L; Roeder, Chris; Ogren, Philip V; Baumgartner, William A; White, Elizabeth; Tipney, Hannah; Hunter, Lawrence

    2011-11-01

    We approached the problems of event detection, argument identification, and negation and speculation detection in the BioNLP'09 information extraction challenge through concept recognition and analysis. Our methodology involved using the OpenDMAP semantic parser with manually written rules. The original OpenDMAP system was updated for this challenge with a broad ontology defined for the events of interest, new linguistic patterns for those events, and specialized coordination handling. We achieved state-of-the-art precision for two of the three tasks, scoring the highest of 24 teams at precision of 71.81 on Task 1 and the highest of 6 teams at precision of 70.97 on Task 2. We provide a detailed analysis of the training data and show that a number of trigger words were ambiguous as to event type, even when their arguments are constrained by semantic class. The data is also shown to have a number of missing annotations. Analysis of a sampling of the comparatively small number of false positives returned by our system shows that major causes of this type of error were failing to recognize second themes in two-theme events, failing to recognize events when they were the arguments to other events, failure to recognize nontheme arguments, and sentence segmentation errors. We show that specifically handling coordination had a small but important impact on the overall performance of the system. The OpenDMAP system and the rule set are available at http://bionlp.sourceforge.net.

  19. HIGH-PRECISION BIOLOGICAL EVENT EXTRACTION: EFFECTS OF SYSTEM AND OF DATA

    Science.gov (United States)

    Cohen, K. Bretonnel; Verspoor, Karin; Johnson, Helen L.; Roeder, Chris; Ogren, Philip V.; Baumgartner, William A.; White, Elizabeth; Tipney, Hannah; Hunter, Lawrence

    2013-01-01

    We approached the problems of event detection, argument identification, and negation and speculation detection in the BioNLP’09 information extraction challenge through concept recognition and analysis. Our methodology involved using the OpenDMAP semantic parser with manually written rules. The original OpenDMAP system was updated for this challenge with a broad ontology defined for the events of interest, new linguistic patterns for those events, and specialized coordination handling. We achieved state-of-the-art precision for two of the three tasks, scoring the highest of 24 teams at precision of 71.81 on Task 1 and the highest of 6 teams at precision of 70.97 on Task 2. We provide a detailed analysis of the training data and show that a number of trigger words were ambiguous as to event type, even when their arguments are constrained by semantic class. The data is also shown to have a number of missing annotations. Analysis of a sampling of the comparatively small number of false positives returned by our system shows that major causes of this type of error were failing to recognize second themes in two-theme events, failing to recognize events when they were the arguments to other events, failure to recognize nontheme arguments, and sentence segmentation errors. We show that specifically handling coordination had a small but important impact on the overall performance of the system. The OpenDMAP system and the rule set are available at http://bionlp.sourceforge.net. PMID:25937701

  20. Design and experimental investigation of an oxy-fuel combustion system for magnetohydrodynamic power extraction

    Science.gov (United States)

    Hernandez, Manuel Johannes

    A general consensus in the scientific and research community is the need to restrict carbon emissions in energy systems. Therefore, extensive research efforts are underway to develop the next generation of energy systems. In the field of power generation, researchers are actively investigating novel methods to produce electricity in a cleaner, efficient form. Recently, Oxy-Combustion for magnetohydrodynamic power extraction has generated significant interest, since the idea was proposed as a method for clean power generation in coal and natural gas power plants. Oxy-combustion technologies have been proposed to provide high enthalpy, electrically conductive flows for direct conversion of electricity. Direct power extraction via magnetohydrodynamics (MHD) can occur as a consequence of the motion of "seeded" combustion products in the presence of magnetic fields. However, oxy-combustion technologies for MHD power extraction has not been demonstrated in the available literature. Furthermore, there are still fundamental unexplored questions remaining, associated with this technology, for MHD power extraction. In this present study, previous magnetohydrodynamic combustion technologies and technical issues in this field were assessed to develop a new combustion system for electrically conductive flows. The research aims were to fully understand the current-state-of-the-art of open-cycle magnetohydrodynamic technologies and present new future directions and concepts. The design criteria, methodology, and technical specifications of an advanced cooled oxy-combustion technology are presented in this dissertation. The design was based on a combined analytical, empirical, and numerical approach. Analytical one-dimensional (1D) design tools initiated design construction. Design variants were analyzed and vetted against performance criteria through the application of computational fluid dynamics modeling. CFD-generated flow fields permitted insightful visualization of the

  1. Impact of ICD lead on the system durability, predictors of long-term survival following ICD system extraction.

    Science.gov (United States)

    Jacheć, Wojciech; Tomasik, Andrzej; Polewczyk, Anna; Kutarski, Andrzej

    2017-10-01

    Implantable cardioverter-defibrillator (ICD) and cardiac resynchronization therapy defibrillator (CRT-D) systems are considered as having higher risk of complication and shorter durability but reasons of this multifactorial phenomenon remain unclear. We aimed to analyze this problem in population of patients with ICD leads referred for lead extraction (TLE). We have compared TLE indications, procedural results, and defined the long-term outcomes of TLE in patients with ICD/CRT-D devices (n  =  482, ICD (+)) with lead extractions in patients with standard pacemakers (n  =  1,402, ICD (-)). Demographic, clinical characteristics, and procedural outcomes were ascertained from single, primary operator registry. Long-term survival data were provided by the National Health Fund. The ICD (+) subgroup had a significantly higher incidence rate of either infective or noninfective indications for TLE. The clinical success rate of extraction was 99.2% in ICD (+) versus 97.4% in ICD (-) (P  =  0.05) at a complication rate of 1.04% versus 2.14% (NS), respectively. In the median follow-up of 3.39 years, 142 patients from the ICD (+) subgroup and 303 from the ICD (-) subgroup died. The highest mortality rate of 41.1% was observed in the ICD (+) subgroup with infective indications. Infection, renal failure, diabetes, and age were the multivariate factors associated with increased mortality in the ICD (+) subgroup. ICD leads remain more vulnerable, with respect to mechanical failure and their propensity to infection, in comparison to pacing leads. Their TLE is very effective at least complication rate, when performed by a highly skilled and experienced operator. However, long-term mortality after their TLE is high and is affected mostly by infections or patient-related factors. © 2017 Wiley Periodicals, Inc.

  2. Spectroscopic study of photoreduction by the fourth harmonic of Nd:YAG laser in a liquid-liquid extraction system

    International Nuclear Information System (INIS)

    Saeki, Morihisa; Yokoyama, Atsushi; Sasaki, Yuji

    2009-01-01

    A new technique for the back-extraction using photoreduction by the fourth harmonic of Nd:YAG laser has been successfully demonstrated in a liquid-liquid extraction system composed of a 1-octanol solution of Eu 3+ (TODGA) n complex and water. The reduced product, Eu 2+ ion, was stabilized by addition of 15-crown-5. The back-extraction process was investigated by laser-induced fluorescence spectroscopy. The results indicated slow diffusion of Eu 2+ (15-crown-5) m in the organic phase and fast transfer through the interface to the water. (author)

  3. Low-High and High-Low Biphasic Injection Forms in Computed Tomography Examinations of the Upper Abdomen

    International Nuclear Information System (INIS)

    Marti-Bonmati, L.; Arana, E.; Tobarra, E.; Sierra, C.

    2006-01-01

    Purpose: To analyze the influence of different biphasic and monophasic injection rate protocols in abdominal computed tomography (CT). Material and Methods: A randomized, consecutive, parallel group study was designed and conducted in 60 patients studied with the same CT helical protocol. Patients were randomly distributed into three groups: (A) monophasic (120 ml at 2.5 ml/s); (B) low-high biphasic (120 ml, first 60 ml at a rate of 2 ml/s, the other 60 ml at 2.5 ml/s); and (C) high-low biphasic (120 ml, first 60 ml at a rate of 2.5 ml/s, the other 60 ml at 2 ml/s). All patients were injected with 300 mg I/ml non-ionic contrast media at a fixed delay time of 55 s. Contrast enhancement efficacy was evaluated by attenuation coefficient measurements. Results: Although non-significant, monophasic protocol enhancements were higher than biphasic protocol enhancements in all measurements except aortic bifurcation (p = 0.003). At this level, biphasic protocols obtained an increased mean enhancement from 7.6% to 2.5% compared to monophasic protocols. Conclusion: Monophasic contrast agent injection in helical CT of the upper abdomen produces a higher enhancement of parenchymal and venous structures. No significant difference was observed between low-high and high-low biphasic protocols

  4. Synchronized oscillations of dimers in biphasic charged fd-virus suspensions.

    Science.gov (United States)

    Kang, K; Piao, S H; Choi, H J

    2016-08-01

    Micron-sized colloidal spheres that are dispersed in an isotropic-nematic biphasic host suspension of charged rods (fd-virus particles) are shown to spontaneously form dimers, which exhibit a synchronized oscillatory motion. Dimer formation is not observed in the monophase of isotropic and nematic suspensions. The synchronized oscillations of dimers are connected to the inhomogeneous state of the host suspension of charged rods (fd viruses) where nematic domains are in coexistence with isotropic regions. The synchronization of oscillations occurs in bulk states, in the absence of an external field. With a low field strength of an applied electric field, the synchronization is rather reduced, but it recovers again when the field is turned off. In this Rapid Communication, we report this observation as an example of the strange attractor, occurring in the mixture of PS (polystyrene) dimers in an isotropic-nematic coexistence biphasic fd-virus network. Furthermore, we highlight that the synchronization of PS-dimer oscillations is the result of a global bifurcation diagram, driven by a delicate balance between the short-attractive "twisted" interaction of PS dimers and long-ranged electrostatic repulsive interactions of charged fd rods. The interest is then in the local enhancement of "twist-nematic" elasticity in reorientation of the dimer oscillations. An analysis of image-time correlations is provided with the data movies and Fourier transforms of averaged orientations for the synchronized oscillations of dimers in the biphasic I-N coexistence concentration of charged fd-virus suspensions.

  5. The influence of topic and systemic administration of copaiba oil on the alveolar wound healing after tooth extraction in rats

    OpenAIRE

    Dias-da-Silva, Marco-Antonio; Pereira, Andresa-Costa; Marin, Miguel-Christian-Castillo; Salgado, Miguel-Angel-Castillo [UNESP

    2013-01-01

    The Copaiba oil has been used as an auxiliary treatment of inflammations, skin disorders and stomach ulcers, however, in dentistry, this alternative medicine has not been investigated yet. The purpose of this study was to evaluate the influence of topic and systemic administration of copaiba oil on the alveolar wound healing after tooth extraction. Twenty-eight wistar male rats had their lower first molar teeth extracted. Subsequently, they were divided in four groups, according to the treatm...

  6. On-line coupling of Micro-Extraction by Packed Sorbent with Sequential Injection Chromatography system for direct extraction and determination of betaxolol in human urine.

    Science.gov (United States)

    Šrámková, Ivana; Chocholouš, Petr; Sklenářová, Hana; Šatínský, Dalibor

    2015-10-01

    A novel approach for automation of Micro-Extraction by Packed Sorbent (MEPS), a solid phase extraction technique, is presented, enabling precise and repeatable liquid handling due to the employment of sequential injection technique. The developed system was used for human urine sample clean-up and pre-concentration of betaxolol before its separation and determination. A commercial MEPS C-18 cartridge was integrated into an SIChrom™ system. The chromatographic separation was performed on a monolithic High Resolution C18 (50×4.6 mm) column which was coupled on-line in the system with Micro-Extraction using an additional selection valve. A mixture of acetonitrile and aqueous solution of 0.5% triethylamine with acetic acid, pH adjusted to 4.5 in ratio 30:70 was used as a mobile phase for elution of betaxolol from MEPS directly onto the monolithic column where the separation took place. Betaxolol was quantified by a fluorescence detector at wavelengths λ(ex)=220 nm and λ(em)=305 nm. The linear calibration range of 5-400 ng mL(-1), with limit of detection 1.5 ng mL(-1) and limit of quantification 5 ng mL(-1) and correlation r=0.9998 for both the standard and urine matrix calibration were achieved. The system recovery was 105±5%; 100±4%; 108±1% for three concentration levels of betaxolol in 10 times diluted urine - 5, 20 and 200 ng mL(-1), respectively. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Energy extraction system using dual-capacitor switching for quench protection of HTS magnet

    International Nuclear Information System (INIS)

    Chi, Yo Jong; Song, Seung Hyun; Jeon, Hae Ryong; Ko, Tae Kuk; Lee, Woo Seung; Kang, Hyoung Ku

    2017-01-01

    The superconducting magnets have a large inductance as well as high operating current. Therefore, mega-joule scale energy can be stored in the magnet. The energy stored in the magnet is sufficient to damage the magnet when a quench occurs. Quench heater and dump resistor can be used to protect the magnet. However, using quench heater to create quench resistors through heat transfer can be slower than instantly switching resistors. Also, electrical short, overheating and breakdown can occur due to quench heater. Moreover, the number of dump resistor should be limited to avoid large terminal voltage. Therefore, in this paper, we propose a quench protection method for extracting the energy stored in a magnet by charging and discharging energy through a capacitor switching without increasing resistance. The simulation results show that the proposed system has a faster current decay within the allowable voltage level

  8. Energy extraction system using dual-capacitor switching for quench protection of HTS magnet

    Energy Technology Data Exchange (ETDEWEB)

    Chi, Yo Jong; Song, Seung Hyun; Jeon, Hae Ryong; Ko, Tae Kuk [Yonsei University, Seoul (Korea, Republic of); Lee, Woo Seung [JH ENGINEERING CO., LTD., Anyang (Korea, Republic of); Kang, Hyoung Ku [Korea National University of Transportation, Chungju (Korea, Republic of)

    2017-09-15

    The superconducting magnets have a large inductance as well as high operating current. Therefore, mega-joule scale energy can be stored in the magnet. The energy stored in the magnet is sufficient to damage the magnet when a quench occurs. Quench heater and dump resistor can be used to protect the magnet. However, using quench heater to create quench resistors through heat transfer can be slower than instantly switching resistors. Also, electrical short, overheating and breakdown can occur due to quench heater. Moreover, the number of dump resistor should be limited to avoid large terminal voltage. Therefore, in this paper, we propose a quench protection method for extracting the energy stored in a magnet by charging and discharging energy through a capacitor switching without increasing resistance. The simulation results show that the proposed system has a faster current decay within the allowable voltage level.

  9. Signal processing method and system for noise removal and signal extraction

    Science.gov (United States)

    Fu, Chi Yung; Petrich, Loren

    2009-04-14

    A signal processing method and system combining smooth level wavelet pre-processing together with artificial neural networks all in the wavelet domain for signal denoising and extraction. Upon receiving a signal corrupted with noise, an n-level decomposition of the signal is performed using a discrete wavelet transform to produce a smooth component and a rough component for each decomposition level. The n.sup.th level smooth component is then inputted into a corresponding neural network pre-trained to filter out noise in that component by pattern recognition in the wavelet domain. Additional rough components, beginning at the highest level, may also be retained and inputted into corresponding neural networks pre-trained to filter out noise in those components also by pattern recognition in the wavelet domain. In any case, an inverse discrete wavelet transform is performed on the combined output from all the neural networks to recover a clean signal back in the time domain.

  10. System architecture for temporal information extraction, representation and reasoning in clinical narrative reports.

    Science.gov (United States)

    Zhou, Li; Friedman, Carol; Parsons, Simon; Hripcsak, George

    2005-01-01

    Exploring temporal information in narrative Electronic Medical Records (EMRs) is essential and challenging. We propose an architecture for an integrated approach to process temporal information in clinical narrative reports. The goal is to initiate and build a foundation that supports applications which assist healthcare practice and research by including the ability to determine the time of clinical events (e.g., past vs. present). Key components include: (1) an annotation schema for temporal expressions and the development of an associated tagger; (2) a natural language processing (NLP) system for encoding and extracting medical events and associating them with formalized temporal data; (3) a post-processor, with a knowledge-based subsystem to help discover implicit information, that resolves temporal expressions and deals with issues such as granularity and vagueness; and (4) a reasoning mechanism which models clinical reports as Simple Temporal Problems (STPs).

  11. Lithium isotope effect in the extraction systems of polyethers: effect of salt concentration

    International Nuclear Information System (INIS)

    Fang Shengqiang; Fu Lian

    1991-01-01

    Separation factors of lithium isotopes at 20 deg C were determined in the extraction systems of B15C5-CHCl 3 /LiBr-H 2 O. The initial concentration of LiBr was controlled in the extent of more than 2 mol/l. It may be established that the increase of LiBr concentration causes a remarkable increase of the separation factor. The essence of this effect due to the change in salt concentration was discussed in connection with examination of relevant phenomena in literature. It can be concluded that the relationship between α and Cm, the concentration of lithium salt, is dependent on K Q and K P express respectively, lithium isotope exchange equilibrium constants between Li-crownether complex and hydrated lithium ion for lithium concentration less than 1-2 mol/l, and between lithium salt ion pair and hydrated lithium ion for lithium concentration more than 2 mol/l in aqueous phase

  12. Basic design of an asymmetric double slow extraction system for the KEK-PS

    International Nuclear Information System (INIS)

    Shoji, Yoshihiko; Marutsuka, Katsumi; Toyama, Takeshi; Sato, Hikaru

    1995-01-01

    Simultaneous extraction to two beam lines of the KEK 12 GeV Proton Synchrotron (KEK-PS) has been theoretically calculated. Unlike double extractions at other facilities, the two extraction lines are not equal in resonant phase. The test operation is also reported. (author)

  13. Pharmacodynamic Study of Interaction of Aqueous Leaf Extract of Psidium Guajava Linn. (Myrtaceae) with Receptor Systems Using Isolated Tissue Preparations.

    Science.gov (United States)

    Mahaseth, R K; Kumar, S; Dutta, Shagun; Sehgal, Ratika; Rajora, Preety; Mathur, Rajani

    2015-01-01

    The present study investigates the interaction of aqueous leaf extract of Psidium guajava with muscarinic, serotonergic and adrenergic receptor system using isolated rat ileum, gastric fundus and trachea, respectively. The concentration-dependent contractile response of aqueous leaf extract of Psidium guajava was parallel and rightward of standard agonists, ACh and 5-HT indicating agonistic activity on muscarinic and serotonergic receptor systems. The inhibition of aqueous leaf extract of Psidium guajava mediated contractions in presence of atropine (10(-7) M) and ketanserin (10(-6) M) confirmed the activity. Relaxant effect of PG (0.2 mg/ml) on carbachol induced pre-contracted rat tracheal chain indicated its agonistic action on adrenergic receptor system. Inhibition (P<0.05) of the action in the presence of propranolol (1 ng/ml) confirmed the activity. It may be concluded that PG possesses agonistic action on muscarinic, serotonergic and adrenergic receptor systems.

  14. EnvMine: A text-mining system for the automatic extraction of contextual information

    Directory of Open Access Journals (Sweden)

    de Lorenzo Victor

    2010-06-01

    Full Text Available Abstract Background For ecological studies, it is crucial to count on adequate descriptions of the environments and samples being studied. Such a description must be done in terms of their physicochemical characteristics, allowing a direct comparison between different environments that would be difficult to do otherwise. Also the characterization must include the precise geographical location, to make possible the study of geographical distributions and biogeographical patterns. Currently, there is no schema for annotating these environmental features, and these data have to be extracted from textual sources (published articles. So far, this had to be performed by manual inspection of the corresponding documents. To facilitate this task, we have developed EnvMine, a set of text-mining tools devoted to retrieve contextual information (physicochemical variables and geographical locations from textual sources of any kind. Results EnvMine is capable of retrieving the physicochemical variables cited in the text, by means of the accurate identification of their associated units of measurement. In this task, the system achieves a recall (percentage of items retrieved of 92% with less than 1% error. Also a Bayesian classifier was tested for distinguishing parts of the text describing environmental characteristics from others dealing with, for instance, experimental settings. Regarding the identification of geographical locations, the system takes advantage of existing databases such as GeoNames to achieve 86% recall with 92% precision. The identification of a location includes also the determination of its exact coordinates (latitude and longitude, thus allowing the calculation of distance between the individual locations. Conclusion EnvMine is a very efficient method for extracting contextual information from different text sources, like published articles or web pages. This tool can help in determining the precise location and physicochemical

  15. New sample preparation method based on task-specific ionic liquids for extraction and determination of copper in urine and wastewater.

    Science.gov (United States)

    Trtić-Petrović, Tatjana; Dimitrijević, Aleksandra; Zdolšek, Nikola; Đorđević, Jelena; Tot, Aleksandar; Vraneš, Milan; Gadžurić, Slobodan

    2018-01-01

    In this study, four hydrophilic ionic liquids (ILs) containing 1-alkyl-3-methylimidazolim cation and either salicylate or chloride anions were synthetized and studied as new task-specific ionic liquids (TSILs) suitable for aqueous biphasic system (ABS) formation and selective one-step extraction of copper(II). TSILs are designed so that the anion is responsible for forming the complex with metal(II) and preventing hydrolysis of metal cations at very strong alkaline pH, whereas the cation is responsible for selective extraction of metal(II)-salicylate complexes. It was found that 1-butyl-3-methylimidazolium salicylate could be used for selective extraction of Cu(II) in the presence of Zn(II), Cd(II), and Pb(II) at very alkaline solution without metal hydroxide formation. It was assumed that formation of metal(II)-salicylate complexes prevents the hydrolysis of the metal ions in alkaline solutions. The determined stability constants for Cu(II)-salicylate complexes, where salicylate was derived from different ionic liquids, indicated that there was no significant influence of the cation of the ionic liquid on the stability of the complexes. The ABS based on 1-butyl-3-methylimidazolium salicylate has been applied as the sample preparation step prior to voltammetric determination of Cu(II). The effect of volume of aqueous sample and IL and extraction time were investigated and optimum extraction conditions were determined. The obtained detection limits were 8 ng dm -3 . The optimized method was applied for the determination of Cu(II) in tap water, wastewater, and urine. The study indicated that application of the ABS based on 1-butyl-3-methylimidazolium salicylate ionic liquid could be successfully applied as the sample preparation method for the determination of Cu(II) from various environmental samples. Graphical abstract Aqueous biphasic system based on task-specific ionic liquid as a sample pretreatment for selective determination of Cu(II) in biological and

  16. Selective extraction and recovery of rare earth metals from phosphor powders in waste fluorescent lamps using an ionic liquid system

    International Nuclear Information System (INIS)

    Yang, Fan; Kubota, Fukiko; Baba, Yuzo; Kamiya, Noriho; Goto, Masahiro

    2013-01-01

    Highlights: • Recycling of rare earth metals from fluorescent lamps was conducted by ionic liquid-mediated extraction. • Acid leaching from a waste phosphor powder was carried out using sulfuric and nitric acids. • An ionic liquid was used as extracting solvent for the rare earth metals. • Selective extraction of rare earth metals from leach solutions was attained. •The extracting ionic liquid phase was recyclable in the recovery process. -- Abstract: The recycling of rare earth metals from phosphor powders in waste fluorescent lamps by solvent extraction using ionic liquids was studied. Acid leaching of rare earth metals from the waste phosphor powder was examined first. Yttrium (Y) and europium (Eu) dissolved readily in the acid solution; however, the leaching of other rare earth metals required substantial energy input. Ionization of target rare earth metals from the waste phosphor powders into the leach solution was critical for their successful recovery. As a high temperature was required for the complete leaching of all rare earth metals, ionic liquids, for which vapor pressure is negligible, were used as an alternative extracting phase to the conventional organic diluent. An extractant, N, N-dioctyldiglycol amic acid (DODGAA), which was recently developed, showed a high affinity for rare earth metal ions in liquid–liquid extraction although a conventional commercial phosphonic extractant did not. An effective recovery of the rare earth metals, Y, Eu, La and Ce, from the metal impurities, Fe, Al and Zn, was achieved from the acidic leach solution of phosphor powders using an ionic liquid containing DODGAA as novel extractant system

  17. Determination of available phosphorus in soils by using a new extraction procedure and a flow injection amperometric system.

    Science.gov (United States)

    Jakmunee, Jaroon; Junsomboon, Jaroon

    2009-09-15

    A new extraction procedure based on an off-line extraction column was proposed for extracting of available phosphorus from soils. The column was fabricated from a plastic syringe fitted at the bottom with a cotton wool and a piece of filter paper to support a soil sample. An aliquot (50 mL) of extracting solution (0.05 M HCl+0.0125 M H(2)SO(4)) was used to extract the sample under gravity flow and the eluate was collected in a polyethylene bottle. The extract was then analyzed for phosphorus contents by a simple flow injection amperometric system, employing a set of three-way solenoid valves as an injection valve. The method is based on the electrochemical reduction of 12-molybdophosphate which is produced on-line by the reaction of orthophosphate with acidic molybdate and the electrical current produced was directly proportional to the concentration of phosphate in range of 0.1-10.0 mg L(-1) PO(4)-P, with a detection limit of 0.02 mg L(-1). Relative standard for 11 replicate injections of 5 mg L(-1) PO(4)-P was 0.5%. A sample through put of 35 h(-1) was achieved, with consumption of 14 mg KCl, 10mg ammonium molybdate and 0.05 mL H(2)SO(4) per analysis. The detection system does not suffer from the interferences that are encountered in the photometric method such as colored substances, colloids, metal ions, silicate and refractive index effect (Schlieren effect). The results obtained by the column extraction procedure were well correlated with those obtained by the steady-state extraction procedure, but showed slightly higher extraction efficiency.

  18. HYPER (hybrid power extraction reactor): a system for clean nuclear energy

    International Nuclear Information System (INIS)

    Park, W.S.; Shin, U.; Han, S.-J.; Song, T.Y.; Choi, B.H.; Park, C.K.

    2000-01-01

    The Korea Atomic Energy Research Institute (KAERI) has been performing accelerator driven system related research and development (RID) called HYPER (hybrid power extraction reactor) for the transmutation of nuclear waste and energy production through the transmutation process. HYPER program is within the frame work of the national mid and long-term nuclear research plan. KAERI is aiming to develop the elemental technologies for the subcritical transmutation system by the year of 2001 and build a small bench scale test facility (∝5 MW) by the year of 2006. Some major features of HYPER have been developed and employed. On-power fueling concepts are employed to keep system power constant with a minimum variation of accelerator power. A hollow cylinder-type metal fuel is designed for the on-line refueling concept. Lead-bismuth (Pb-Bi) is adopted as a coolant and spallation target material. 1 GeV 16 mA proton beam is designed to be provided for HYPER. HYPER is to transmute about 380 kg of TRU a year and produce 1000 MW of power. The support ratio of HYPER for LWR units producing the same power is believed to be 5∝6. (orig.)

  19. RAMI modeling of plant systems for proposed tritium production and extraction facilities

    International Nuclear Information System (INIS)

    Blanchard, A.

    2000-01-01

    The control of life-cycle cost is a primary concern during the development, construction, operation, and decommissioning of DOE systems and facilities. An effective tool that can be used to control these costs, beginning with the design stage, is called a reliability, availability, maintainability, and inspectability analysis or, simply, RAMI for short. In 1997, RAMI technology was introduced to the Savannah River Site with applications at the conceptual design stage beginning with the Accelerator Production of Tritium (APT) Project and later extended to the Commercial Light Water Reactor (CLWR) Tritium Extraction Facility (TEF) Project. More recently it has been applied to the as-build Water Treatment Facilities designed for ground water environmental restoration. This new technology and database was applied to the assessment of balance-of-plant systems for the APT Conceptual Design Report. Initial results from the Heat Removal System Assessment revealed that the system conceptual design would cause the APT to fall short of its annual production goal. Using RAM technology to immediately assess this situation, it was demonstrated that the product loss could be gained back by upgrading the system's chiller unit capacity at a cost of less than $1.3 million. The reclaimed production is worth approximately $100 million. The RAM technology has now been extended to assess the conceptual design for the CLWR-TEF Project. More specifically, this technology and database is being used to translate high level availability goals into lower level system design requirements that will ensure the TEF meets its production goal. Results, from the limited number of system assessments performed to date, have already been used to modify the conceptual design for a remote handling system, improving its availability to the point that a redundant system, with its associated costs of installation and operation may no longer be required. RAMI results were also used to justify the elimination

  20. Silica-based ionic liquid coating for 96-blade system for extraction of aminoacids from complex matrixes

    Energy Technology Data Exchange (ETDEWEB)

    Mousavi, Fatemeh; Pawliszyn, Janusz, E-mail: janusz@uwaterloo.ca

    2013-11-25

    Graphical abstract: -- Highlights: •Silica-based 1-vinyl-3-octadecylimidazolium bromide ionic liquid was synthesized and characterized. •The synthesized polymer was immobilized on the stainless steel blade using polyacrylonitrile glue. •SiImC{sub 18}-PAN 96-blade SPME was applied as an extraction phase for extraction of highly polar compounds in grape matrix. •This system provides high extraction efficiency and reproducibility for up to 50 extractions from tartaric buffer and 20 extractions from grape pulp. -- Abstract: 1-Vinyl-3-octadecylimidazolium bromide ionic liquid [C{sub 18}VIm]Br was prepared and used for the modification of mercaptopropyl-functionalized silica (Si-MPS) through surface radical chain-transfer addition. The synthesized octadecylimidazolium-modified silica (SiImC{sub 18}) was characterized by thermogravimetric analysis (TGA), infrared spectroscopy (IR), {sup 13}C NMR and {sup 29}Si NMR spectroscopy and used as an extraction phase for the automated 96-blade solid phase microextraction (SPME) system with thin-film geometry using polyacrylonitrile (PAN) glue. The new proposed extraction phase was applied for extraction of aminoacids from grape pulp, and LC–MS–MS method was developed for separation of model compounds. Extraction efficiency, reusability, linearity, limit of detection, limit of quantitation and matrix effect were evaluated. The whole process of sample preparation for the proposed method requires 270 min for 96 samples simultaneously (60 min preconditioning, 90 min extraction, 60 min desorption and 60 min for carryover step) using 96-blade SPME system. Inter-blade and intra-blade reproducibility were in the respective ranges of 5–13 and 3–10% relative standard deviation (RSD) for all model compounds. Limits of detection and quantitation of the proposed SPME-LC–MS/MS system for analysis of analytes were found to range from 0.1 to 1.0 and 0.5 to 3.0 μg L{sup −1}, respectively. Standard addition calibration was

  1. Characterization of Carya illinoiensis and Juglans regia oils obtained by different extraction systems

    Directory of Open Access Journals (Sweden)

    Tainara Costa-Singh

    2015-05-01

    Full Text Available It is extremely important to evaluate the extraction processes of vegetable oils used in food, considering that the nuts are rich sources of triacylglycerols. Thus, the present study aimed at comparing the methods of solvent extraction and extraction by pressing of the lipid fractions of walnut (Juglans regia and pecan nut (Carya illinoensis, in order to elucidate their influence on the content of bioactive substances. The samples were analyzed regarding fatty acid profile, tocopherols, phytosterols, carotenoids, and phenolic compounds, presenting relevant quantities of these bioactive substances. It was found that the extraction of oils by pressing minimized degradation of tocopherol when compared to solvent extraction. However, solvent extraction is more efficient to extract bioactive compounds such as phytosterols, carotenoids, and phenolic compounds.

  2. The effects of Vitex agnus castus extract and its interaction with dopaminergic system on LH and testosterone in male mice.

    Science.gov (United States)

    Nasri, Sima; Oryan, Shahrbano; Rohani, Ali Haeri; Amin, Gholam Reza

    2007-07-15

    The purpose of this study was to evaluate the probable effects of Vitex agnus castus (Vac.) on the male reproductive physiology. It is a well known fact that LH secretion from the anterior pituitary of mammals is controlled by many neurotransmiters such as dopamine. In this experiment, we have studied the effect of Vac. extract on the LH and testosterone hormones and its interaction with the dopaminergic system on male mice. In order to evaluate these effects, we used the hydroalcoholic Vac. extract (for extraction we used percolation technique) injection with the following doses: 65, 165, 265, 365 and 465 mg kg-', bromocriptine as a dopamine receptor agonist (5, 10, 20 mg kg(-1)) and haloperidol as a dopamine receptor antagonist (1, 1.5, 2, 2.5, 3 mg kg(-1)). To study the interaction between Vac. extract and dopaminergic system, we injected the optimum doses of Vac. with bromocriptine or haloperidol at the same time. Intraperitoneal injections were applied in all experiments, once a day for 30 days. The control group remained intact and the sham group received vehicle. After the last injection, we collected the animal blood serums for hormonal assays. LH and testosterone were measured by Radio Immuno Assay (RIA). LH and testosterone, showed significant decrease in bromocriptine group and haloperidol increased these hormones. Vac. extract decreased significantly the LH and testosterone levels. The coadministration of Vac. extract and bromocriptine decreased LH and testosterone. Coadministration of Vac. extract and haloperidol decreased LH and testosterone levels. These results suggest: dopamine regulates the gonadotroph-leydig cells axis. It appears that Vac. exertes effects through dopaminergic system and other pathways. The findings of this study show we can use Vac. extract for pathological cases of increasing LH and testosterone.

  3. MODULAR CAUSTIC SIDE SOLVENT EXTRACTION UNIT (MCU) GAMMA MONITORS SYSTEM FINAL REPORT

    Energy Technology Data Exchange (ETDEWEB)

    Casella, V

    2005-12-15

    The Department of Energy (DOE) selected Caustic-Side Solvent Extraction (CSSX) as the preferred technology for the removal of radioactive cesium from High-Level Waste (HLW) at the Savannah River Site (SRS). Before the full-scale Salt Waste Processing Facility (SWPF) becomes operational, the Closure Business Unit (CBU) plans to process a portion of dissolved saltcake waste through a Modular CSSX Unit (MCU). This work was derived from Technical Task Request SP-TTR-2004-00013, ''Gamma Monitor for MCU''. The deliverables for this task are the hardware and software for the gamma monitors and a report summarizing the testing and acceptance of this equipment for use in the MCU. Gamma-ray monitors are required to: (1) Measure the Cs-137 concentration in the decontaminated salt solution before entering the DSS (Decontaminated Salt Solution) Hold Tank, (2) Measure the Cs-137 concentration in the strip effluent before entering the Strip Effluent Hold Tank, (3) Verify proper operation of the solvent extraction system by verifying material balance within the process (The DSS Hold Tank Cs-137 concentration will be very low and the Cs-137 concentration in the Strip Effluent Hold Tank will be fifteen times higher than the Cs-137 concentration in the Feed Tank.) Sodium iodide monitors are used to measure the Cs-137 concentration in the piping before the DSS Hold tank, while GM monitors are used for Cs-137 measurements before the Strip Effluent Hold Tank. Tungsten shields were designed using Monte Carlo calculations and fabricated to reduce the process background radiation at the detector positions. These monitors were calibrated with NIST traceable standards that were specially made to be the same as the piping being monitored. Since this gamma ray monitoring system is unique, specially designed software was written and acceptance tested by Savannah River National Laboratory personnel. The software is a LabView-based application that serves as a unified

  4. MODULAR CAUSTIC SIDE SOLVENT EXTRACTION UNIT (MCU) GAMMA MONITORS SYSTEM FINAL REPORT

    International Nuclear Information System (INIS)

    Casella, V

    2005-01-01

    The Department of Energy (DOE) selected Caustic-Side Solvent Extraction (CSSX) as the preferred technology for the removal of radioactive cesium from High-Level Waste (HLW) at the Savannah River Site (SRS). Before the full-scale Salt Waste Processing Facility (SWPF) becomes operational, the Closure Business Unit (CBU) plans to process a portion of dissolved saltcake waste through a Modular CSSX Unit (MCU). This work was derived from Technical Task Request SP-TTR-2004-00013, ''Gamma Monitor for MCU''. The deliverables for this task are the hardware and software for the gamma monitors and a report summarizing the testing and acceptance of this equipment for use in the MCU. Gamma-ray monitors are required to: (1) Measure the Cs-137 concentration in the decontaminated salt solution before entering the DSS (Decontaminated Salt Solution) Hold Tank, (2) Measure the Cs-137 concentration in the strip effluent before entering the Strip Effluent Hold Tank, (3) Verify proper operation of the solvent extraction system by verifying material balance within the process (The DSS Hold Tank Cs-137 concentration will be very low and the Cs-137 concentration in the Strip Effluent Hold Tank will be fifteen times higher than the Cs-137 concentration in the Feed Tank.) Sodium iodide monitors are used to measure the Cs-137 concentration in the piping before the DSS Hold tank, while GM monitors are used for Cs-137 measurements before the Strip Effluent Hold Tank. Tungsten shields were designed using Monte Carlo calculations and fabricated to reduce the process background radiation at the detector positions. These monitors were calibrated with NIST traceable standards that were specially made to be the same as the piping being monitored. Since this gamma ray monitoring system is unique, specially designed software was written and acceptance tested by Savannah River National Laboratory personnel. The software is a LabView-based application that serves as a unified interface for controlling

  5. Extraction of Uranium from Seawater: Design and Testing of a Symbiotic System

    Energy Technology Data Exchange (ETDEWEB)

    Slocum, Alex [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

    2018-02-22

    The U.S. Department of Energy in October 2014 awarded the Massachusetts Institute of Technology (MIT) a Nuclear Energy University Program grant (DE-NE0008268) to investigate the design and testing of a symbiotic system to harvest uranium from seawater. As defined in the proposal, the goals for the project are: 1. Address the design of machines for seawater uranium mining. 2. Develop design rules for a uranium harvesting system that would be integrated into an offshore wind power tower. 3. Fabricate a 1/50th size scale prototype for bench and pool-testing to verify initial analysis and theory. 4. Design, build, and test a second 1/10th size scale prototype in the ocean for more comprehensive testing and validation. This report describes work done as part of DE-NE0008268 from 10/01/2014 to 11/30/2017 entitled, “Extraction of Uranium from Seawater: Design and Testing of a Symbiotic System.” This effort is part of the Seawater Uranium Recovery Program. This report details the publications and presentations to date on the project, an introduction to the project’s goals and background research into previous work done to achieve these goals thus far. From there, the report describes an algorithm developed during the project used to optimize the adsorption of uranium by changing mechanical parameters such as immersion time and adsorbent reuses is described. Next, a design tool developed as part of the project to determine the global feasibility of symbiotic uranium harvesting systems. Additionally, the report details work done on shell enclosures for uranium adsorption. Moving on, the results from the design, building, and testing of a 1/50th physical scale prototype of a highly feasible symbiotic uranium harvester is described. Then, the report describes the results from flume experiment used to determine the affect of enclosure shells on the uptake of uranium by the adsorbent they enclose. From there the report details the design of a Symbiotic Machine for Ocean u

  6. Application of Ultrasound in a Closed System: Optimum Condition for Antioxidants Extraction of Blackberry (Rubus fructicosus) Residues.

    Science.gov (United States)

    Zafra-Rojas, Quinatzin Y; Cruz-Cansino, Nelly S; Quintero-Lira, Aurora; Gómez-Aldapa, Carlos A; Alanís-García, Ernesto; Cervantes-Elizarrarás, Alicia; Güemes-Vera, Norma; Ramírez-Moreno, Esther

    2016-07-21

    Blackberry processing generates up to 20% of residues composed mainly of peel, seeds and pulp that are abundant in flavonoids. The objective of this study was to optimize the ultrasound conditions, in a closed system, for antioxidants extraction, using the response surface methodology. Blackberry (Rubus fructicosus) residues were analyzed for total phenolics, total anthocyanins, and antioxidant activity by ABTS and DPPH. The selected independent variables were ultrasound amplitude (X₁: 80%-90%) and extraction time (X₂: 10-15 min), and results were compared with conventional extraction methods. The optimal conditions for antioxidants extraction were 91% amplitude for 15 min. The results for total phenolic content and anthocyanins and antioxidant activity by ABTS and DPPH were of 1201.23 mg gallic acid equivalent (GAE)/100 g dry weight basis (dw); 379.12 mg/100 g·dw; 6318.98 µmol Trolox equivalent (TE)/100 g·dw and 9617.22 µmol TE/100 g·dw, respectively. Compared to solvent extraction methods (water and ethanol), ultrasound achieved higher extraction of all compounds except for anthocyanins. The results obtained demonstrated that ultrasound is an alternative to improve extraction yield of antioxidants from fruit residues such as blackberry.

  7. Application of Ultrasound in a Closed System: Optimum Condition for Antioxidants Extraction of Blackberry (Rubus fructicosus Residues

    Directory of Open Access Journals (Sweden)

    Quinatzin Y. Zafra-Rojas

    2016-07-01

    Full Text Available Blackberry processing generates up to 20% of residues composed mainly of peel, seeds and pulp that are abundant in flavonoids. The objective of this study was to optimize the ultrasound conditions, in a closed system, for antioxidants extraction, using the response surface methodology. Blackberry (Rubus fructicosus residues were analyzed for total phenolics, total anthocyanins, and antioxidant activity by ABTS and DPPH. The selected independent variables were ultrasound amplitude (X1: 80%–90% and extraction time (X2: 10–15 min, and results were compared with conventional extraction methods. The optimal conditions for antioxidants extraction were 91% amplitude for 15 min. The results for total phenolic content and anthocyanins and antioxidant activity by ABTS and DPPH were of 1201.23 mg gallic acid equivalent (GAE/100 g dry weight basis (dw; 379.12 mg/100 g·dw; 6318.98 µmol Trolox equivalent (TE/100 g·dw and 9617.22 µmol TE/100 g·dw, respectively. Compared to solvent extraction methods (water and ethanol, ultrasound achieved higher extraction of all compounds except for anthocyanins. The results obtained demonstrated that ultrasound is an alternative to improve extraction yield of antioxidants from fruit residues such as blackberry.

  8. High temperature high velocity direct power extraction using an open-cycle oxy-combustion system

    Energy Technology Data Exchange (ETDEWEB)

    Love, Norman [Univ. of Texas, El Paso, TX (United States)

    2017-09-29

    The implementation of oxy-fuel technology in fossil-fuel power plants may contribute to increased system efficiencies and a reduction of pollutant emissions. One technology that has potential to utilize the temperature of undiluted oxy-combustion flames is open-cycle magnetohydrodynamic (MHD) power generators. These systems can be configured as a topping cycle and provide high enthalpy, electrically conductive flows for direct conversion of electricity. This report presents the design and modeling strategies of a MHD combustor operating at temperatures exceeding 3000 K. Throughout the study, computational fluid dynamics (CFD) models were extensively used as a design and optimization tool. A lab-scale 60 kWth model was designed, manufactured and tested as part of this project. A fully-coupled numerical method was developed in ANSYS FLUENT to characterize the heat transfer in the system. This study revealed that nozzle heat transfer may be predicted through a 40% reduction of the semi-empirical Bartz correlation. Experimental results showed good agreement with the numerical evaluation, with the combustor exhibiting a favorable performance when tested during extended time periods. A transient numerical method was employed to analyze fuel injector geometries for the 60-kW combustor. The ANSYS FLUENT study revealed that counter-swirl inlets achieve a uniform pressure and velocity ratio when the ports of the injector length to diameter ratio (L/D) is 4. An angle of 115 degrees was found to increase distribution efficiency. The findings show that this oxy-combustion concept is capable of providing a high-enthalpy environment for seeding, in order to render the flow to be conductive. Based on previous fin