WorldWideScience

Sample records for biomasse lignocellulosiche produzione

  1. Ethanol from lignocellulosic biomasses; Etanolo da biomasse lignocellulosiche. Produzione di etanolo da paglia di grano mediante pretrattamento di steam explosion, idrolisi enzimatica e fermentazione

    Energy Technology Data Exchange (ETDEWEB)

    Ricci, E.; Viola, E.; Zimbardi, F.; Braccio, G. [ENEA, Divisione Fonti Rinnovabili di Energia, Centro Ricerche Trisaia, Policoro, Matera (Italy); Cuna, D. [Faucitano Srl, Milan (Italy)

    2001-07-01

    In this report are presented results achieved on the process optimisation of bioethanol production from wheat straw, carried out within the ENEA's project of biomass exploitation for renewable energy. The process consists of three main steps: 1) biomass pretreatment by means of steam explosion; 2) enzymatic hydrolysis of the cellulose fraction; 3) fermentation of glucose. To perform the hydrolysis step, two commercial enzymatic mixtures have been employed, mainly composed by {beta}-glucosidase (cellobiase), endo-glucanase and exo-glucanase. The ethanologenic yeast Saccharomyces cerevisiae has been used to ferment the glucose in he hydrolyzates. Hydrolysis yield of 97% has been obtained with steam exploded wheat straw treated at 220{sup 0}C for 3 minutes and an enzyme to substrate ratio of 4%. It has been pointed out the necessity of washing with water the pretreated what straw, in order to remove the biomass degradation products, which have shown an inhibition effect on the yeast. At the best process conditions, a fermentation yield of 95% has been achieved. In the Simultaneous Saccharification and Fermentation process, a global conversion of 92% has been obtained, which corresponds to the production of about 170 grams of ethanol per kilogram of exploded straw. [Italian] Si riportano i risultati di un'attivita' di ricerca finalizzata all'ottimizzazione del processo di produzione di etanolo da paglia di grano. Il processo esaminato consta di un pretrattamento mediante steam explosion della paglia, seguito da idrolisi enzimatica della cellulosa e fermentazione del glucosio ottenuto. Per effettuare l'idrolisi sono stati utilizzati due preparati enzimatici disponibili commercialmente, costituiti da {beta}-glucosidasi, endo-glucanasi ed eso-glucanasi. Per la fermentazione del glucosio negli idrolizzati e' stato impiegato il lievito Saccharomyces cerevisae. E' stata raggiunta un'efficienza massima di idrolisi del 97% utilizzando

  2. State of the art on bioethanol production; Stato dell'arte della produzione di bioetanolo

    Energy Technology Data Exchange (ETDEWEB)

    Barisano, D.; De Bari, I.; Viola, E.; Zimbardi, F.; Braccio, G. [ENEA, Divisione Fonti Rinnovabili di Energia, Centro Ricerche Trisaia, Policoro, Matera (Italy); Cantarella, M.; Gallifuoco, A. [L' Aquila Univ., L' Aquila (Italy). Dipt. di Ingegneria Chimica e dei Materiali

    2001-07-01

    The state of the art, deals with the ethanol production from current processes based on the use of sugar and starch as feedstock and those under development based on lignocellulosic biomass. In the first section are reported the commercially available processes together with hints to the newest technologies. As regard the ethanol production from lignocellulosics, it has been collected data on the biomass availability in Europe as energy crops, industrial crops, agricultural residues and domestic waste. It is provided a bibliographic study on the technologies and processes under development worldwide for the conversion of lignocellulosics into ethanol. Finally, a brief discussion on the economics highlights the near term viability of producing ethanol by this way. [Italian] Questo lavoro tratta della produzione di etanolo da diverse biomasse, compreso i materiali lignocellulosici. Sono riportati cenni al mercato mondiale ed europeo dell'etanolo insieme ad una breve rassegna dei processi impiegati correntemente; si tratta per lo piu' di tecnologie ormai mature basate sull'utilizzo di piante ad alto contenuto di zucchero o di amido. Per quanto riguarda la produzione di etanolo da biomasse lignocellulosiche, sono riportati i risultati di un'indagine statistica sulla disponibilita' in Europa di questi materiali in termini di coltivazini dedicate, residui agro-forestali e rifiuti domestici. E' riportata altresi una ricerca bibliografica sui recenti sviluppi dei processi di conversione a etanolo su scala banco e pilota. Infine, una breve discussione sugli aspetti economici connessi all'utilizzo di materiali lignocellulosici per la produzione di etanolo mostra come questi processi si stiano avvicinando alla completa fattibilita'.

  3. Steam explosion and new production processes for pulping industry: technical and economical feasibility; Steam explosion e nuovi processi di produzione cartaria: fattibilita` tecnico-economica

    Energy Technology Data Exchange (ETDEWEB)

    Viggiano, D. [ENEA, Centro Ricerche Trisaia, Rotondella, Matera (Italy). Dipt. Energia; Bramanti, O. [ENEA, Centro Ricerche Trisaia, Rotondella, Matera (Italy). Dipt. Innovazione

    1998-05-01

    scientifica e tecnologica internazionali sono stati sempre piu` indirizzati allo sviluppo di nuovi processi di lavorazione ed alla valorizzazione, al recupero es alla trasformazione di materie prime alternative e, soprattutto, rinnovabili. A tale riguardo, gia` da alcuni anni, si sta affermando la consapevolezza da parte degli imprenditori della carta di rispondere ad una triplice esigenza: quella dovuta alle normative antinquinamento sempre piu` severe, quella relativa all`opinione pubblica sensibile alla tutela ambientale e quella di mercato legata all`acquisizione di un `vantaggio competitivo` nei confronti della concorrenza. Il presente lavoro si inserisce in tale scenario realizzando una valutazione tecnico-economica dell`applicazione in ambito industriale della tecnologia di steam-explosion ed delle biomasse ligno-cellulosiche, intese sia come scarti di lavorazione agro-industriali che nella piu` recente accezione di colture industriali (specie C{sub 4}, C{sub 5}) specificatamente destinate al recupero di aree marginali (set aside) e successivo utilizzo a fini produttivi ed energetici. Nel contempo, viene preso in esame l`introduzione del processo di trattamento di Steam Explosion per un conveniente inserimento in cicli di produzione industriale, con particolare riferimento a quelli della carta.

  4. Orso, ghianda e faggiola: produzione trofica e fattori ambientali

    Directory of Open Access Journals (Sweden)

    M. Romano

    2003-10-01

    Full Text Available La produzione di ghianda e faggiola è stata monitorata nel 2001 e 2002 nell'area del progetto LIFE tramite griglia di plot (maglia= 500 m distribuiti in maniera sistematica nell'area di studio. In faggeta sono stati campionati 214 plot da settembre a dicembre 2001 e 130 tra ottobre e novembre 2002. Nei querceti sono stati campionati 143 plot da gennaio a marzo 2002 e 143 plot da settembre a dicembre 2002. Nei plot (circolari, Ø= 40 m i frutti sono stati raccolti in 17 stazioni (superficie= 1 m² e sono stati successivamente divisi in 5 tipi in base alla grandezza e condizione del seme. Sia il numero totale di faggiole raccolte (148.1369 vs. 9.412 sia il numero medio di faggiole/plot (692,2 vs. 72,4 è stato maggiore nel 2001 rispetto al 2002. Analogamente, la densità media di faggiole (tipo 1+2 nell'autunno 2001 è stata maggiore di quella del 2002 (26,8 vs. 1,8. La produzione della ghianda di cerro è stata maggiore nel 2002 rispetto al 2001. Nell'inverno 2001/2002 sono state raccolte 5.445 ghiande, mentre nell'autunno 2002 il numero di ghiande raccolte è stato pari a 13.814. Il numero medio di ghiande di cerro totali / plot è stato pari a 57,9 nel 2001/2002 e a 121,2 nel 2002. Le evidenti differenze di produzione di faggiola (0,34 1259 g e ghianda (0,434 - 9,99 g tra i plot sembrano attribuibili alla gestione selvicolturale. Infatti, analisi preliminari hanno evidenziato che i fattori stazionali (quota, esposizione non incidono in misura significativa sulla quantità di frutti prodotti. L'uso dello spazio nell'orso bruno è influenzato dalla disponibilità trofica, che nel periodo autunnale è importante in relazione a svernamento e gravidanza. Poiché, in funzione della disponibilità di faggiola risulta una variazione nell'alimentazione, si raccomandano interventi di monitoraggio della produzione e distribuzione della faggiola e delle fonti trofiche che ad essa si alternano. Così, sarà possibile inquadrare in un contesto territoriale

  5. VALUTAZIONE DELLA PRODUZIONE SCRITTA: PARAMETRI, GRIGLIE E SOGGETTIVITÀ

    Directory of Open Access Journals (Sweden)

    Claudia Matthiae

    2010-09-01

    Full Text Available La valutazione della produzione scritta non costituisce certo un compito agevole per il docente. Quali parametri vanno necessariamente valutati e su quanti livelli/punti dovrebbero spalmarsi? Come conferire rigore e scientificità alla correzione sottraendola alla soggettività? Gli enti certificatori delle competenze linguistiche si avvalgono di parametri rigorosi, ma sembrerebbe che nella prassi quotidiana i docenti siano piuttosto restii  all'impiego di griglie. Il presente contributo, alieno da ogni pretesa di esaustività, si prefigge come obiettivo quello di affrontare un problema spinoso suggerendo percorsi valutativi possibili nella consapevolezza che, alla stregua di quanto avviene per il manuale, la scelta dell'eventuale griglia di valutazione  è e deve rimanere una questione meramente personale.   It is certainly not an easy task for teachers to evaluate writing. Which parameters should be evaluated, on how many levels and how many points should they be worth? How can correction be rigorous and scientific and not subjective? Linguistic competency certifiers refer to strict parameters, but it seems that in daily practice teachers do not like to use grids very much. This paper, far from being exhaustive, aims at addressing this difficult problem by suggesting possible ways for carrying out evaluation, keeping in mind that in the same was as for a manual, the choice of using an evaluation grid is and should remain a merely personal question.

  6. IL PROCESSO DI PRODUZIONE SCRITTA: LA COESIONE VERBALE IN TESTI DI SCUOLA PRIMARIA

    Directory of Open Access Journals (Sweden)

    Fabiana Rosi

    2015-02-01

    Full Text Available Una delle principali difficoltà che incontrano i bambini della scuola primaria nella produzione scritta riguarda la coesione verbale, ovvero il mantenimento lungo il testo della dimensione temporale inizialmente selezionata per riportare gli eventi. L’articolo esamina questo specifico tipo di competenza testuale negli alunni di sei classi del secondo ciclo della scuola primaria, tre delle quali hanno partecipato alla sperimentazione educativa sulla produzione di testi scritti “Osservare l’interlingua”. Il confronto fra i dati raccolti all’inizio e alla fine dell’anno scolastico mostra una riduzione dei salti immotivati da un tempo verbale all’altro, definiti shift temporali, nei testi prodotti nelle classi del campione sperimentale in misura maggiore rispetto a quelle di controllo e sottolinea gli effetti positivi, a breve e lungo termine, di una didattica task-based condotta con approccio inclusivo, cooperativo ed attivo.  The process of writing: verb cohesion in primary school textsOne of principal difficulties in producing written texts for primary school pupils concerns verb cohesion, i.e. maintaining the temporal dimension initially chosen for expressing events throughout the text. The paper examines this specific textual competence in pupils from six classes within second cycle of primary school. Three of these classes were involved in the “Observing interlanguage” project focused on written production. The comparison of data collected at the beginning and the end of school year shows a decrease in temporal shifts (transitions from one verb tense to another in the texts produced by the students involved in the project with regard to the control group. These findings highlight the positive effects, both short-term and long-term, of task-based teaching through an inclusive, cooperative and active approach. 

  7. Le Terme a sud del Pretorio di Gortina. Produzione e circolazione dei contenitori da trasporto

    Directory of Open Access Journals (Sweden)

    Ilaria De Aloe

    2010-03-01

    Full Text Available La posizione centrale nell’Egeo ed i pochi giorni di navigazione dall’Africa e dall’Egitto, come dalla Siria e Palestina, hanno reso la città di Gortina, e Creta stessa, un punto nevralgico all’interno delle rotte commerciali di collegamento e distribuzione di beni tra le sponde del Mediterraneo. Lo studio delle anfore rinvenute nelle campagne di scavo 2003-2006 presso le Terme a sud del Pretorio, ed il necessario confronto con le grandi quantità di materiali provenienti soprattutto dai contesti del Pretorio confermano questa intricata rete commerciale. Già tra Ellenismo e prima età imperiale romana, Gortina svolse una funzione di mercato di raccolta e probabilmente di smistamento delle merci provenienti dall’Occidente e dall’Egeo, assumendo poi nella piena età imperiale, un ruolo sempre più attivo nella produzione delle stesse. La mutata situazione socio-economica dell’età tardo romana - bizantina, nonché la fondazione di una nuova capitale, Costantinopoli, portò Creta e Gortina ad avere scambi commerciali e collegamenti intensi soprattutto con le aree orientali del Mediterraneo privilegiando l’importazione di prodotti dall’esterno.

  8. Methane production in the biosphere; La produzione di metano nella biosfera: il ruolo degli animali da allevamento

    Energy Technology Data Exchange (ETDEWEB)

    Sauvant, D. [Stazione di Nutrizione e Alimentazione (Italy)

    1999-04-01

    Methane is a greenhouse gas. A part of methane production is of agricultural origin. The emissions related to animal organisms are evaluated and discussed. [Italian] Il metano e' una molecola che contribuisce all'effetto serra e alle conseguenze climatiche che ne derivano. Una parte di metano e' di orgine agricola, legata in particolare alla produzione animale. Questo breve documento vuole focalizzare le conoscenze su quest'ultimo aspetto, limitandosi alle emissioni attribuibili agli organismi animali, escludendo pero' i loro rifiuti.

  9. Produzione di bioidrogeno in dark fermentation da scarti dell'industria agroalimentale mediante l'impiego di batteri ipertermofili

    OpenAIRE

    Alberini, Andrea

    2013-01-01

    La presente tesi di dottorato ha come argomento la produzione d’idrogeno per via fermentativa sfruttando il metabolismo anaerobico di particolari batteri estremofili del genere Thermotoga. In questo lavoro, svolto in seno al progetto Bio-Hydro, sfruttando reattori batch da 116 mL, è stato selezionato il ceppo migliore di Thermotoga fra i quatto ceppi testati: T. neapolitana. Una volta individuato il candidato batterico migliore è stato individuato il valore ottimale di pH (8.5 a t.amb) per la...

  10. Ascoli 1808-1940. Luoghi della produzione e architetture per il lavoro

    Directory of Open Access Journals (Sweden)

    Roberto Di Girolami

    2014-06-01

    Full Text Available Nel quadro economico-produttivo dell’Italia tra Ottocento e Novecento, Ascoli rappresenta un caso forse di minor interesse in ambito nazionale o internazionale, ma un caso non certamente anomalo. Sul binomio arretratezza/sviluppo, come altre realtà urbane anche il capoluogo piceno inizia il suo lento processo di modernizzazione economico-produttiva, con effettivi riscontri sull’aspetto fisico della città. La conoscenza storica della struttura produttiva di Ascoli ha messo in luce il carattere più o meno innovativo delle produzioni e dei processi lavorativi, nonché una realtà fisica di natura particolare, con la presenza di una rete di unità produttive diffuse nel tessuto urbano e con un alto grado di integrazione con la città, contribuendo a delinearne la storia e la forma stessa. Riflettendo su un possibile futuro del passato urbano di Ascoli, va evidenziato che storia della città, storia dell’industria e storia dei luoghi della produzione s’intrecciano senza soluzione di continuità.  Within the Italian production context between the 19th and 20th century, Ascoli may have been a less interesting case both on a national and international level but it certainly hasn’t been an anomalous one. As for backwardness and development, like other urban realities, Ascoli also begins a slow process of economic modernization, which has a significant impact on the town’s physical features. Studies on the evolution of Ascoli’s production network, have highlighted the somewhat innovative character of the products and working process, as well as a particular appearance characterized by several manufacturing plants rising throughout the town area, which perfectly integrate with the town itself and contribute to build its history and shape. Thinking about the possible reuse of Ascoli’s old buildings, it’s important to point out that town history and history of the industry and production areas weave together with no interruption.

  11. Ricerca del bosone di Higgs in produzione associata col bosone vettore W, nello stato finale $WH ->(\\mu\

    CERN Document Server

    Grippo, Maria Teresa

    Il Modello Standard (MS) è la teoria scientifica più dibattuta degli ultimi anni nel mondo della fisica delle alte energie. Essa racchiude i fondamenti della materia e descrive le interazioni che regolano l'universo. Il MS è stato confermato in numerosi esperimenti, quali LEP e Tevatron, ma presenta ancora un ultimo interrogativo relativo all'origine della massa delle particelle. Il MS cerca di spiegare ciò tramite il meccanismo di Higgs, proposto da Peter Higgs nel 1964 \\cite{Higgs}: viene introdotta una nuova particella, chiamata \\emph{bosone di Higgs}, che ha lo scopo tramite il suddetto meccanismo di fornire massa alle particelle. Di tale particella non si conosce la massa, che viene infatti assunta come parametro libero della teoria. Scopo di tale lavoro di tesi è stato quello di studiare presso l'esperimento CMS (\\emph{Compact Muon Solenoid}) a LHC (\\emph{Large Hadron Collider}) il canale di produzione associata WH, nell'intervallo di massa 115 GeV/$c^{2} \\leq m_H \\leq $ 135 GeV/$c^{2}$, negli stat...

  12. Il museo partecipativo sul web: forme di partecipazione dell’utente alla produzione culturale e alla creazione di valore culturale

    Directory of Open Access Journals (Sweden)

    Elisa Bonacini

    2012-05-01

    Full Text Available Obiettivo di questo lavoro è un inquadramento sia del nuovo rapporto fra il museo partecipativo e l’utenza che delle forme di partecipazione dell’utenza alla produzione culturale e alla creazione di valore culturale, alla luce delle potenzialità offerte dalle ICT, soprattutto dal web e dai vari social media. Questo nuovo rapporto, che ha le sue radici più profonde proprio nell’ampia adozione di tutte le piattaforme tecnologiche oggi in uso, consente anche una reinterpretazione del significato stesso di cultural value. Il quadro, che viene qui delineato ed arricchito da numerosi esempi soprattutto stranieri, chiarisce anche quanto l’aspetto partecipativo e l’utilizzo di tags, folksonomie e user generated contents possano incidere sulla fidelizzazione dell’utenza. Infine, in una tabella presentata a fine del contributo, si evidenziano le maggiori componenti che caratterizzano il definitivo passaggio dalla fase Museo 1.0 alla fase Museo 2.0. The aim of this paper is a framework both of the new relationship between the participatory museum and the audience and a framework of multiple forms of audience participation in cultural production and in the creation of cultural value, given the potential offered by ICTs, especially the web and various social media. This new relationship, which has its deepest roots just in the adoption of all technology platforms in use today, also allows for a reinterpretation of the meaning of cultural value. The framework, outlined here and enriched by numerous examples especially foreigners, also makes clear that participation and use of tags, folksonomies and user-generated contents may have an impact on users loyalty. Finally, presented in a table at the end of the paper, we highlight the most important features characterizing the transition from the Museum 1.0 phase to the Museum 2.0 one.

  13. Verso un'estetica della macchina. Le nozioni di oggetto e di reale nella produzione artistica postmoderna

    Directory of Open Access Journals (Sweden)

    Simone Frangi

    2011-10-01

    Full Text Available

    Il saggio esamina la pratica del ready-made nella scena artistica post-storica. Nel contesto di una ricodificazione del rapporto tra artistico e politico, i concetti di reale e oggetto veicolano una riflessione sul problema del realismo nella produzione Pop e Minimalista. Grazie ad una costellazione di autori (Lyotard, Deleuze e Guattari, Francastel, Lacan, Rancière esploreremo il modo in cui il Postmoderno modula la propria impresa veritativa catturando atti extra-artistici e registrando l’emergenza di una dimensione macchinina.

    Towards an aesthetics of the machine.The notions of object and real in postmodernist artistic production

    This essay is conceived as a theoretical inquiry that seeks to examine ready-made practice as one of the most pertinent moments of the genesis of the post-historical artistic scene. In the framework of a recoded articulation of the art and the politics, concepts of Real and object will constitute the ground for a theoretical speculation on the question of realism in Pop Art and Minimalism. Thanks to a constellation of authors (Lyotard, Deleuze e Guattari, Francastel, Lacan, Rancière we will explore how Postmodernism shapes its enterprise by “capturing” extra-artistic acts and how this intrusion implies the emergence of mechanical dimension.

  14. Experimental valuation of specific hospital waste production in sanitary departments and surgeries; Valutazione sperimenatle della produzione specifica di rifiuti sanitari a rischio infettivo da reparti e gruppi operatori di una struttura ospedaliera

    Energy Technology Data Exchange (ETDEWEB)

    Serra, R.

    1999-10-01

    Experimental measures of hospital waste production in sanitary departments and surgeries at highly specialised hospital have been carried out. The salient differences in waste specific production in several departments explain relevantly the variability of hospital waste production reported in technical literature. [Italian] Sono state effettuate rilevazioni sperimentali della produzione di rifiuti speciali sanitari a rischio infettivo dai reparti digenza, di terapia intensiva e dalle sale operatorie di una struttura opsedaliera ad alta specializzazione. Le differenze significative riscontrate tra reparti o sale operatorie afferenti a unita' funzionali diverse, rendono conto della variabilita' dei valori di produzione di rifiuti speciali sanitari a rischio infettivo da strutture ospedaliere riscontrate nella letteratura.

  15. Impact of nitrous acid photolysis on the total hydroxyl radical budget during the Limitation of Oxidant Production/Pianura Padana Produzione di Ozono study in Milan

    Science.gov (United States)

    Alicke, B.; Platt, U.; Stutz, J.

    2002-11-01

    The photolysis of nitrous acid (HONO) in the early morning hours is believed to be a significant source of hydroxyl radicals (OH), the most important daytime oxidizing species. Although the importance of this mechanism has been recognized for many years, no accurate experimental quantification is available. Here we present measurements of HONO, NO2, SO2, O3 and HCHO by Differential Optical Absorption Spectroscopy (DOAS) during the Limitation of Oxidant Production/Pianura Padana Produzione di Ozono (LOOP/PIPAPO) study in May-June 1998 in Milan, Italy. The concentration of NO and J(NO2)/J(HONO) were simultaneously monitored by in situ monitors. The photolysis frequencies of HCHO and O3 were determined with a radiative transfer model. High nocturnal HONO mixing ratios of up to 4.4 ppb were regularly observed. Elevated daytime HONO levels during cloudy periods show that the formation of HONO proceeds after sunrise and therefore also represents a source of hydroxyl radicals throughout the day. Averaged over 24 hours, HCHO photolysis is the most important source of OH in Milan, followed by either ozone or HONO photolysis. Our observations indicate that on certain days the OH production from HONO can be even more important than that from ozone photolysis. The diurnal variation of the different OH formation mechanisms shows that HONO photolysis is by far the most important source in the early hours of the morning, and can be as large as and even surpass the total OH production at noon.

  16. Biomass pretreatment

    Science.gov (United States)

    Hennessey, Susan Marie; Friend, Julie; Elander, Richard T; Tucker, III, Melvin P

    2013-05-21

    A method is provided for producing an improved pretreated biomass product for use in saccharification followed by fermentation to produce a target chemical that includes removal of saccharification and or fermentation inhibitors from the pretreated biomass product. Specifically, the pretreated biomass product derived from using the present method has fewer inhibitors of saccharification and/or fermentation without a loss in sugar content.

  17. Biomass recalcitrance

    DEFF Research Database (Denmark)

    Felby, Claus

    2009-01-01

    , enzymatic hydrolysis, and product fermentation options. Biomass Recalcitrance is essential reading for researchers, process chemists and engineers working in biomass conversion, also plant scientists working in cell wall biology and plant biotechnology. This book examines the connection between biomass...... - this collective resistance is known as "biomass recalcitrance." Breakthrough technologies are needed to overcome barriers to developing cost-effective processes for converting biomass to fuels and chemicals. This book examines the connection between biomass structure, ultrastructure, and composition......, to resistance to enzymatic deconstruction, with the aim of discovering new cost-effective technologies for biorefineries. It contains chapters on topics extending from the highest levels of biorefinery design and biomass life-cycle analysis, to detailed aspects of plant cell wall structure, chemical treatments...

  18. Biomass recalcitrance

    DEFF Research Database (Denmark)

    Felby, Claus

    2009-01-01

    Alternative and renewable fuels derived from lignocellulosic biomass offer a promising alternative to conventional energy sources, and provide energy security, economic growth, and environmental benefits. However, plant cell walls naturally resist decomposition from microbes and enzymes - this co......Alternative and renewable fuels derived from lignocellulosic biomass offer a promising alternative to conventional energy sources, and provide energy security, economic growth, and environmental benefits. However, plant cell walls naturally resist decomposition from microbes and enzymes...... - this collective resistance is known as "biomass recalcitrance." Breakthrough technologies are needed to overcome barriers to developing cost-effective processes for converting biomass to fuels and chemicals. This book examines the connection between biomass structure, ultrastructure, and composition......, to resistance to enzymatic deconstruction, with the aim of discovering new cost-effective technologies for biorefineries. It contains chapters on topics extending from the highest levels of biorefinery design and biomass life-cycle analysis, to detailed aspects of plant cell wall structure, chemical treatments...

  19. Experimental comparison between RBCOD production from OFMSW and from primary sludge for BNR systems; Analisi comparativa sperimentale della produzione di RBCOD da FORSU e da fanghi primari per sistemi BNR

    Energy Technology Data Exchange (ETDEWEB)

    Andreottola, G.; Bombieri, A.; Foladori, P.; Ragazzi, M.; Zanetti, G. [Trent Univ., Trent (Italy). Dipt. di Ingegneria Civile e Ambientale

    2000-12-01

    The topic of this work is the comparison of two ways of readily biodegradable COD production (RBCOD) in order to use it in wastewater treatment plants WWWTP aimed at nutrient removal. In the catchment area of a WWTP both primary sludge and organic fraction municipal solid waste are available for fermentation. Two experimentations were developed in order to study the efficiency of the strategies. Balances were developed for a comparison referring to the same catchment area for wastewater and solid waste. [Italian] Il presente lavoro ha lo scopo di mettere a confronto due diverse modalita' di produzione di COD rapidamente biodegradabile (RBCOD) da utilizzare negli impianti di depurazione per la rimozione biologica dei nutrienti. Come fonte per tale produzione, in un medesimo bacino di servizio di un depruatore, si dispone infatti dei fanghi primari oppure della frazione organica putrescibile di rifiuti urbani. Entrambi i materiali possono essere fatti fermentare per produrre RBCOD. A tal fine sono state sviluppate due sperimentazioni per studiare il comportamento dei suddetti materiali e sono stati elaborati bilanci per poter confrontare le due soluzioni a parita' di bacino di servizio.

  20. Biomass [updated

    Energy Technology Data Exchange (ETDEWEB)

    Turhollow Jr, Anthony F [ORNL

    2016-01-01

    Biomass resources and conversion technologies are diverse. Substantial biomass resources exist including woody crops, herbaceous perennials and annuals, forest resources, agricultural residues, and algae. Conversion processes available include fermentation, gasification, pyrolysis, anaerobic digestion, combustion, and transesterification. Bioderived products include liquid fuels (e.g. ethanol, biodiesel, and gasoline and diesel substitutes), gases, electricity, biochemical, and wood pellets. At present the major sources of biomass-derived liquid fuels are from first generation biofuels; ethanol from maize and sugar cane (89 billion L in 2013) and biodiesel from vegetable oils and fats (24 billion liters in 2011). For other than traditional uses, policy in the forms of mandates, targets, subsidies, and greenhouse gas emission targets has largely been driving biomass utilization. Second generation biofuels have been slow to take off.

  1. Correlation between leachate production and construction-operation criteria of MSW landfills; Correlazione tra la produzione di percolato e le caratteristiche costruttive e gestionali di discariche per RSU

    Energy Technology Data Exchange (ETDEWEB)

    Collivignarelli, C.; Bertanza, G.; Cavallari, S. [Brescia Univ., Brescia (Italy). Dipt. di Ingegneria Civile

    2001-06-01

    seguito all'esperienza progressivamente acquisita. L'analisi dei dati gestionali conferma che alcuni fattori hanno influenzato la produzione di percolato; in particolare, per quanto riguarda i criteri costruttivi: le caratteristiche dei pozzi di estrazione del biogas (durante la fase di discarica aperta); le caratteristiche del sistema di copertura (nella fase di post-chiusura); per quanto riguarda i criteri gestionali: la compattazione dei rifiuti (in fase di discarica aperta); la durata del periodo precedente la realizzazione della copertura finale.

  2. Biomass potential

    Energy Technology Data Exchange (ETDEWEB)

    Asplund, D. [VTT Energy, Espoo (Finland)

    1996-12-31

    Biomass resources of the industrialised countries are enormous, if only a small fraction of set-aside fields were used for energy crops. Forest resources could also be utilised more efficiently than at present for large-scale energy production. The energy content of the annual net growth of the total wood biomass is estimated to be 180 million toe in Europe without the former USSR, and about 50 million toe of that in the EC area, in 1990. Presently, the harvesting methods of forest biomass for energy production are not yet generally competitive. Among the most promising methods are integrated harvesting methods, which supply both raw material to the industry and wood fuel for energy production. Several new methods for separate harvesting of energy wood are being developed in many countries. (orig.)

  3. La produzione cartografica del CIGA

    Directory of Open Access Journals (Sweden)

    Maurizio Monteleone

    2006-12-01

    Full Text Available L’ Aeronautica Militare per poter assolvere la propria missione ha la necessità di conoscere l’ambiente in cui opera, le caratteristiche morfologiche del territorio e le informazioni relative agli spazi aerei. Già agli albori del volo fu avvertita l’esigenza di avere una cartografia adeguata alle esigenze del nuovo mezzo e furono quindi fatti notevoli sforzi per realizzare carte dedicate alla navigazione aerea: nel 1923 fu pubblicata una carta aeronautica in scala 1:250.000, probabilmente la prima al mondo nel suo genere. A seguito dell’introduzione di sempre più sofisticati sistemi d’arma, fu necessaria la creazione di un Ente specifico che potesse dedicarsi con competenza e specificità all’attività produttiva nel settore della cartografia aeronautica. Il 15 febbraio 1976 presso il palazzo dell’Aeronautica Militare. fu così creato il CIGA (Centro Informazioni GeotopograficheAeronautiche al quale furono affidati i compiti esecutivi della preesistente Sezione Fotocartografica dello SMA che gestiva dal 1941 tutta l’attività cartografica dell’Aeronautica Militare. Nel 1977 il CIGA venne trasferito sull’Aeroporto di Pratica diMare. Dal primo gennaio 2001 il CIGA è ufficialmente riconosciuto come Organo Cartografico dello Stato

  4. Biomass IGCC

    Energy Technology Data Exchange (ETDEWEB)

    Salo, K.; Keraenen, H. [Enviropower Inc., Espoo (Finland)

    1996-12-31

    Enviropower Inc. is developing a modern power plant concept based on pressurised fluidized-bed gasification and gas turbine combined cycle (IGCC). The process is capable of maximising the electricity production with a variety of solid fuels - different biomass and coal types - mixed or separately. The development work is conducted on many levels. These and demonstration efforts are highlighted in this article. The feasibility of a pressurised gasification based processes compared to competing technologies in different applications is discussed. The potential of power production from biomass is also reviewed. (orig.) 4 refs.

  5. Biomass shock pretreatment

    Science.gov (United States)

    Holtzapple, Mark T.; Madison, Maxine Jones; Ramirez, Rocio Sierra; Deimund, Mark A.; Falls, Matthew; Dunkelman, John J.

    2014-07-01

    Methods and apparatus for treating biomass that may include introducing a biomass to a chamber; exposing the biomass in the chamber to a shock event to produce a shocked biomass; and transferring the shocked biomass from the chamber. In some aspects, the method may include pretreating the biomass with a chemical before introducing the biomass to the chamber and/or after transferring shocked biomass from the chamber.

  6. Material flow analysis in sugar production for the assessment of residue production; Anche dallo zucchero si producono residui. Analisi dei flussi di materia della produzione dello zucchero per la stima delle quantita' di residui prodotti

    Energy Technology Data Exchange (ETDEWEB)

    Toscano, G. [Ancona Univ., Ancona (Italy). Dipt. di Biotecnologie agrarie ed ambientali

    2001-06-01

    As far as residue disposal is concerned, sugar production represents one of the most interesting processes of agro-industry. In point of fact, the amount of sugar beets processed in one season by a sugar refinery is in the order of hundreds of thousands of tons, while only a little over one tenth of them is made into sugar. As a consequence, the residual mass gives rise to a disposal problem, which represents an essential aspect of the economy of the whole process, which must, among all else, deal with European Union restrictions. During the last few years, in particular, the sector is undergoing a transformation phase due to the reduction of both sugar exports (EU commitment as a result of the 1994 GATT agreement) and financial support to agriculture production. Moreover, the by-products of the process are ever more suffering the competition of other raw materials made available at competitive prices by the international market. It is therefore necessary to find - also for residues of scarce practical interest - alternative outlets able to redress the difficult balance between a correct environmental destination and the reduction of production costs. This article aims at analysing the set of problems, hoping to offer useful elements for the prospective definition of new disposal techniques. The analysis point of reference is a sugar refinery in central Italy, characterised by a productive potential of over 10,000 ton/day of sugar beets. [Italian] La produzione dello zucchero rappresenta uno dei processi dell'industria agroalimentare piu' interessanti in tema di smaltimento dei residui della lavorazione. Di fatto, la quantita' di barbabietole lavorate nel corso della stagione da parte di uno zuccherificio e' dell'ordine delle centinaia di migliaia di tonnellate a stagione e poco piu' di un decimo di questa viene trasformato in zucchero. Per la restante massa residua, sorge quindi il problema dello smaltimento che rappresenta un aspetto

  7. Biomass torrefaction mill

    Energy Technology Data Exchange (ETDEWEB)

    Sprouse, Kenneth M.

    2016-05-17

    A biomass torrefaction system includes a mill which receives a raw biomass feedstock and operates at temperatures above 400 F (204 C) to generate a dusty flue gas which contains a milled biomass product.

  8. Biomass torrefaction mill

    Science.gov (United States)

    Sprouse, Kenneth M.

    2016-05-17

    A biomass torrefaction system includes a mill which receives a raw biomass feedstock and operates at temperatures above 400 F (204 C) to generate a dusty flue gas which contains a milled biomass product.

  9. Photo catalytic degradation of toluene diamine solution from poliuretane foam land emission treatment; Degradazione fotocatalitica di soluzioni di toluendiammina derivanti dal lavaggio di emissioni da impianti di produzione schiume poliuretamiche

    Energy Technology Data Exchange (ETDEWEB)

    Onofrio, M.; Cugliandolo, A. [Politecnico di Torino (Italy). Dipt. di Georisorse e Territorio

    1999-06-01

    The aim of this work is the study of the abatement of emission of TDI (toluenediisocyanate) from polyurethane foam plants. As the treatment involves wet scrubbing of TDI emissions, the first step of the study has been the analysis of the reaction between TDI and water. Several methods for the measurements of the concentration of the reaction product (TDA, toluenediamine)have been tested. Subsequently a photo catalytic process for TDA removal has been investigated. The laboratory tests have been carried put both in batch and continuous operation mode. TiO{sub 2} has been adopted as photo catalyst for both kind of tests. In the batch configuration it has been suspended in water by mechanical stirring, while the continuous systems has been supported on the walls of the reactor. The obtained results show that the studies contaminant can be actually oxidized by this treatment. Furthermore a theoretical model has been obtained permitting to the predict accurately abatement times and process efficiency. [Italian] Scopo del presete lavoro e' stato lo studio di sistemi per l'abbattimento delle emissioni TDI (toluendiisocianato) provenienti da impianti di produzione di schiume poliuretamiche. Nell'ipotesi di realizzare un abbattimento ad umido dei vapori di TDI, in un primo tempo si e' analizzato il comportamento di tale sostanza in acqua, verificandone la reattivita' con produzione dell'ammina corrispondente TDA (toluendiammina). Successivamente l'obiettivo della ricerca e' stato rivolto allo studio di fattibilita' della degradazione fotocatalitica di questo inquinante in fase acquosa. A tal fine sono state condotte una serie di prove secondo due diverse modalita': una prima parte in batch ed una seconda con alimentazione in continuo. Per entrambi i trattamenti di abbattimento fotocatalitico si e' previsto l'impiego di TiO{sub 2} quale fotocatalizzatore, disperso tramite agitazione continua nelle prove batch e

  10. Energy from Biomass for Conversion of Biomass

    Science.gov (United States)

    Abolins, J.; Gravitis, J.

    2009-01-01

    Along with estimates of minimum energy required by steam explosion pre-treatment of biomass some general problems concerning biomass conversion into chemicals, materials, and fuels are discussed. The energy necessary for processing biomass by steam explosion auto-hydrolysis is compared with the heat content of wood and calculated in terms of the amount of saturated steam consumed per unit mass of the dry content of wood biomass. The fraction of processed biomass available for conversion after steam explosion pre-treatment is presented as function of the amount of steam consumed per unit mass of the dry content of wood. The estimates based on a simple model of energy flows show the energy required by steam explosion pre-treatment of biomass being within 10% of the heat content of biomass - a realistic amount demonstrating that energy for the process can be supplied from a reasonable proportion of biomass used as the source of energy for steam explosion pre-treatment.

  11. My Biomass, Your Biomass, Our Solution

    Science.gov (United States)

    The US is pursuing an array of renewable energy sources to reduce reliance on imported fossil fuels and reduce greenhouse gas emissions. Biomass energy and biomass ethanol are key components in the pursuit. The need for biomass feedstock to produce sufficient ethanol to meet any of the numerous stat...

  12. Biomass treatment method

    Science.gov (United States)

    Friend, Julie; Elander, Richard T.; Tucker, III; Melvin P.; Lyons, Robert C.

    2010-10-26

    A method for treating biomass was developed that uses an apparatus which moves a biomass and dilute aqueous ammonia mixture through reaction chambers without compaction. The apparatus moves the biomass using a non-compressing piston. The resulting treated biomass is saccharified to produce fermentable sugars.

  13. Rheology of concentrated biomass

    Science.gov (United States)

    J.R. Samaniuk; J. Wang; T.W. Root; C.T. Scott; D.J. Klingenberg

    2011-01-01

    Economic processing of lignocellulosic biomass requires handling the biomass at high solids concentration. This creates challenges because concentrated biomass behaves as a Bingham-like material with large yield stresses. Here we employ torque rheometry to measure the rheological properties of concentrated lignocellulosic biomass (corn stover). Yield stresses obtained...

  14. Methods for pretreating biomass

    Science.gov (United States)

    Balan, Venkatesh; Dale, Bruce E; Chundawat, Shishir; Sousa, Leonardo

    2017-05-09

    A method for pretreating biomass is provided, which includes, in a reactor, allowing gaseous ammonia to condense on the biomass and react with water present in the biomass to produce pretreated biomass, wherein reactivity of polysaccharides in the biomass is increased during subsequent biological conversion as compared to the reactivity of polysaccharides in biomass which has not been pretreated. A method for pretreating biomass with a liquid ammonia and recovering the liquid ammonia is also provided. Related systems which include a biochemical or biofuel production facility are also disclosed.

  15. Recovery of metal scrap from recycling processes for the manufacturing of shields for low frequency electromagnetic fields; Recupero di sfridi metallici ottenuti da processi di riciclo per la produzione di pannellature schermanti per campi magnetici a bassa frequenza

    Energy Technology Data Exchange (ETDEWEB)

    Plescia, P.; Maccari, D. [Consiglio delle Ricerche, Istituto per la Tecnologia dei Materiali e dei Processi Energetici, Milan (Italy); De Stefano, L. [Electric Power Production Company, Tuturano, Brindisi (Italy)

    2001-10-01

    In this paper the results about the recycling of metallic scraps for manufacturing of electromagnetic shields are presented. Preliminary data on shields for low frequency magnetic fields are reported. Shielding materials are prepared with metallic scraps derived by recycling process from many kinds of industrial productions. This new shielding material can reduce magnetic field at less than 55% and it can be easily produced at low cost from many kind of industrial wastes. Some characteristics of these new shields are reported. [Italian] Il problema della schermatura dei campi elettromagnetici alternati (CM) nelle strutture abitative sta diventando di interesse prioritario, soprattutto per la forte pressione esercitata dall'opinione pubblica e dalla ricerche epidemiologiche che sembrano indicare una diretta relazione tra campi elettromagnetici a bassa frequenza ed alcune gravi patologie. La ricerca che viene presentata in anteprima in questo lavoro riporta i dati preliminari relativi alla messa a punto di schermi per campi magnetici generati da tensioni alternate a frequenza industriale (50 Hz). I materiali schermanti sono stati preparati con sfridi metallici provenienti da cicli di riciclo di diverse produzioni industriali. Il tipo di materiale prodotto scelto ha una capacita' schermante del campo magnetico pari al 55% del valore iniziale e puo' essere prodotto con facilita' ed a basso costo, partendo da diverse tipologie di polimeri e di rifiuti a base metallica. La particolare tipologia di polimeri utilizzati permette di preparare materiali schermanti con differenti spessori, colori e caratteristiche meccaniche. Il principio di funzionamento, il processo di produzione e i materiali ottenuti sono oggetto di brevetto industriale.

  16. Energy from Biomass.

    Science.gov (United States)

    Carioca, J. O. B.; And Others

    1987-01-01

    Discusses how biomass in the form of fuelwood, crop residues, and animal dung can be converted into fuels such as biogas and ethanol to replace or supplement fossil fuels. Argues for future decentralized, integrated biomass energy development. (TW)

  17. Energy from Biomass.

    Science.gov (United States)

    Carioca, J. O. B.; And Others

    1987-01-01

    Discusses how biomass in the form of fuelwood, crop residues, and animal dung can be converted into fuels such as biogas and ethanol to replace or supplement fossil fuels. Argues for future decentralized, integrated biomass energy development. (TW)

  18. Pretreated densified biomass products

    Science.gov (United States)

    Dale, Bruce E; Ritchie, Bryan; Marshall, Derek

    2014-03-18

    A product comprising at least one densified biomass particulate of a given mass having no added binder and comprised of a plurality of lignin-coated plant biomass fibers is provided, wherein the at least one densified biomass particulate has an intrinsic density substantially equivalent to a binder-containing densified biomass particulate of the same given mass and h a substantially smooth, non-flakey outer surface. Methods for using and making the product are also described.

  19. Small Modular Biomass Systems

    Energy Technology Data Exchange (ETDEWEB)

    None

    2002-12-01

    This fact sheet provides information about modular biomass systems. Small modular biomass systems can help supply electricity to rural areas, businesses, and the billions of people who live without power worldwide. These systems use locally available biomass fuels such as wood, crop waste, animal manures, and landfill gas.

  20. Application of life cycle assessment to production processes of environmentally sustainable concrete, prepared with artificial aggregates; Applicazione della metodologia life cycle assessment alla produzione di conclomerati cementizi di qualita' contenenti aggregati artificiali

    Energy Technology Data Exchange (ETDEWEB)

    Vaccaro, R. [Italrecuperi, Pozzuoli (Italy); Colangelo, F. [Basilicata Univ., Poteza (Italy). Dip. di Ungegneria e Fisica dell' Ambiente; Palumbo, M. [Federico II Univ., Napoli (Italy). Dipartimento di Ingegneria e Fisica dell' Ambiente; Cioffi, R. [Parthenope Univ., Napoli (Italy). Dipartimento per le Tecnologie

    2005-08-01

    This paper is about the application of Life Cycle Assessment (L.C.A.) on environmentally sustainable concrete production processes. The goal of this experimentations is to assess environmental impact and energy demand related to concrete production, by using, in different admixtures, natural and artificial aggregates, belonging from treatments of different kind of industrial wastes characterized by very small particle sizes. Particular attention was concentrated on the utilization of fine fraction since it is difficult to recover in usual fields of recycling (i.e. aggers, crowl spaces, etc.). This study follows the approach from cradle to cradle. This experimentation was conducted in relation to four concrete admixtures produced, one of them containing only natural aggregate, and the other ones obtained by substituting the 10% of aggregate respectively with inert wastes as construction and demolition waste (CeD waste). cement kiln dust (CKD) and marble sludge. For all admixtures six different end-life scenarios have been proposed, one of them considers all materials transported in landfill while the other ones consider a partial transportation on landfill (15%) and a recycle of the 85% of wastes obtained after demolition of structures. [Italian] Il presente lavoro ha come oggetto l'applicazione della metodologia Life Cycle Assessment (L.C.A.) ai processi produttivi di calcestruzzi eco-compatibili. L'obiettivo dello studio e' quello di valutare il carico ambientale ed il consumo energetico associato alla produzione di calcestruzzo impiegando, in differenti miscele, aggregati artificiali provenienti dal trattamento di differenti tipologie di scarti industriali di pezzatura molto piccola. E' stata posta particolare attenzione all'utilizzo della frazione fine in quanto quest'ultima risulta piu' difficilmente recuperabile nei consueti campi d'impiego (es. rienpimento per sottofondi stradali, vespai, etc.). L

  1. Gasification of Woody Biomass.

    Science.gov (United States)

    Dai, Jianjun; Saayman, Jean; Grace, John R; Ellis, Naoko

    2015-01-01

    Interest in biomass to produce heat, power, liquid fuels, hydrogen, and value-added chemicals with reduced greenhouse gas emissions is increasing worldwide. Gasification is becoming a promising technology for biomass utilization with a positive environmental impact. This review focuses specifically on woody biomass gasification and recent advances in the field. The physical properties, chemical structure, and composition of biomass greatly affect gasification performance, pretreatment, and handling. Primary and secondary catalysts are of key importance to improve the conversion and cracking of tars, and lime-enhanced gasification advantageously combines CO2 capture with gasification. These topics are covered here, including the reaction mechanisms and biomass characterization. Experimental research and industrial experience are investigated to elucidate concepts, processes, and characteristics of woody biomass gasification and to identify challenges.

  2. Complex pendulum biomass sensor

    Science.gov (United States)

    Hoskinson, Reed L.; Kenney, Kevin L.; Perrenoud, Ben C.

    2007-12-25

    A complex pendulum system biomass sensor having a plurality of pendulums. The plurality of pendulums allow the system to detect a biomass height and density. Each pendulum has an angular deflection sensor and a deflector at a unique height. The pendulums are passed through the biomass and readings from the angular deflection sensors are fed into a control system. The control system determines whether adjustment of machine settings is appropriate and either displays an output to the operator, or adjusts automatically adjusts the machine settings, such as the speed, at which the pendulums are passed through the biomass. In an alternate embodiment, an entanglement sensor is also passed through the biomass to determine the amount of biomass entanglement. This measure of entanglement is also fed into the control system.

  3. Process for treating biomass

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, Timothy J; Teymouri, Farzaneh

    2015-11-04

    This invention is directed to a process for treating biomass. The biomass is treated with a biomass swelling agent within the vessel to swell or rupture at least a portion of the biomass. A portion of the swelling agent is removed from a first end of the vessel following the treatment. Then steam is introduced into a second end of the vessel different from the first end to further remove swelling agent from the vessel in such a manner that the swelling agent exits the vessel at a relatively low water content.

  4. Gasification-based biomass

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2009-01-18

    The gasification-based biomass section of the Renewable Energy Technology Characterizations describes the technical and economic status of this emerging renewable energy option for electricity supply.

  5. Process for treating biomass

    Science.gov (United States)

    Campbell, Timothy J.; Teymouri, Farzaneh

    2015-08-11

    This invention is directed to a process for treating biomass. The biomass is treated with a biomass swelling agent within the vessel to swell or rupture at least a portion of the biomass. A portion of the swelling agent is removed from a first end of the vessel following the treatment. Then steam is introduced into a second end of the vessel different from the first end to further remove swelling agent from the vessel in such a manner that the swelling agent exits the vessel at a relatively low water content.

  6. Energetische Verwertung von Biomasse

    Science.gov (United States)

    Zahoransky, Richard; Allelein, Hans-Josef; Bollin, Elmar; Oehler, Helmut; Schelling, Udo

    Etwa 0,1% der Solarenergie wandeln sich durch Photosynthese aus dem Kohlendioxid der Luft in Biomasse um. Die Biomassen sind als Festbrennstoff nutzbar oder zu gasförmigen Brennstoffen weiterverarbeitbar. Zwei Arten von Biomassen sind zu unterscheiden: Anfallende Biomasse

  7. World wide biomass resources

    NARCIS (Netherlands)

    Faaij, A.P.C.

    2012-01-01

    In a wide variety of scenarios, policy strategies, and studies that address the future world energy demand and the reduction of greenhouse gas emissions, biomass is considered to play a major role as renewable energy carrier. Over the past decades, the modern use of biomass has increased rapidly in

  8. World wide biomass resources

    NARCIS (Netherlands)

    Faaij, A.P.C.

    2012-01-01

    In a wide variety of scenarios, policy strategies, and studies that address the future world energy demand and the reduction of greenhouse gas emissions, biomass is considered to play a major role as renewable energy carrier. Over the past decades, the modern use of biomass has increased rapidly in

  9. Bulk chemicals from biomass

    NARCIS (Netherlands)

    Haveren, van J.; Scott, E.L.; Sanders, J.P.M.

    2008-01-01

    Given the current robust forces driving sustainable production, and available biomass conversion technologies, biomass-based routes are expected to make a significant impact on the production of bulk chemicals within 10 years, and a huge impact within 20-30 years. In the Port of Rotterdam there is a

  10. Hydrothermal conversion of biomass

    NARCIS (Netherlands)

    Knezevic, Dragan

    2009-01-01

    This thesis presents research of hydrothermal conversion of biomass (HTC). In this process, hot compressed water (subcritical water) is used as the reaction medium. Therefore this technique is suitable for conversion of wet biomass/ waste streams. By working at high pressures, the evaporation of wat

  11. World wide biomass resources

    NARCIS (Netherlands)

    Faaij, A.P.C.

    2012-01-01

    In a wide variety of scenarios, policy strategies, and studies that address the future world energy demand and the reduction of greenhouse gas emissions, biomass is considered to play a major role as renewable energy carrier. Over the past decades, the modern use of biomass has increased

  12. Bulk chemicals from biomass

    NARCIS (Netherlands)

    Haveren, van J.; Scott, E.L.; Sanders, J.P.M.

    2008-01-01

    Given the current robust forces driving sustainable production, and available biomass conversion technologies, biomass-based routes are expected to make a significant impact on the production of bulk chemicals within 10 years, and a huge impact within 20-30 years. In the Port of Rotterdam there is a

  13. Termisk forgasning af biomasse

    DEFF Research Database (Denmark)

    Henriksen, Ulrik Birk

    2005-01-01

    The title of this Ph.D. thesis is: Thermal Gasification of Biomass. Compilation of activities in the ”Biomass Gasification Group” at Technical University of Denmark (DTU). This thesis gives a presentation of selected activities in the Biomass Gasification Group at DTU. The activities are related...... to thermal gasification of biomass. Focus is on gasification for decentralised cogeneration of heat and power, and on related research on fundamental processes. In order to insure continuity of the presentation the other activities in the group, have also been described. The group was started in the late...... nineteen eighties. Originally, the main aim was to collect and transfer knowledge about gasification of straw. Very quickly it became clear, that knowledge was insufficient and the available technology, in most cases, unsuitable for converting the Danish biomass. The need for such technology...

  14. Hydrothermal liquefaction of biomass

    DEFF Research Database (Denmark)

    Toor, Saqib; Rosendahl, Lasse; Rudolf, Andreas

    2011-01-01

    This article reviews the hydrothermal liquefaction of biomass with the aim of describing the current status of the technology. Hydrothermal liquefaction is a medium-temperature, high-pressure thermochemical process, which produces a liquid product, often called bio-oil or bi-crude. During...... the hydrothermal liquefaction process, the macromolecules of the biomass are first hydrolyzed and/or degraded into smaller molecules. Many of the produced molecules are unstable and reactive and can recombine into larger ones. During this process, a substantial part of the oxygen in the biomass is removed...... by dehydration or decarboxylation. The chemical properties of bio-oil are highly dependent of the biomass substrate composition. Biomass constitutes of various components such as protein; carbohydrates, lignin and fat, and each of them produce distinct spectra of compounds during hydrothermal liquefaction...

  15. Archeologia della produzione architettonica. Le tecniche costruttive

    Directory of Open Access Journals (Sweden)

    Mannoni, Tiziano

    2005-12-01

    Full Text Available In the field of the building techniques used in the construction of the walls, the majority of the classifications consists of the formal aspects of visible surfaces. These classifications use some attentions distinguishing stratigraphic units and in the field of the aesthetic aspects of surfaces. As the walls take part of the most important load-bearing structure, isn’t possible to speak of the techniques used in the construction of the walls without trying to understand how the different types of wall effectively operate from a static point of view. So it’s necessary to check and to understand the whole volume of each technique used in the construction of the walls, and if there are general or particular rules deductibles from the visible surfaces. In this paper we suggest, also, an classification of the «families» of the most recognized techniques used in the construction of the walls, on the basis of their constructive, functional and formal systems.La maggior parte delle classificazioni dei modi di costruire murari si basa sugli aspetti formali delle superfici visibili, con certe utilità nel distinguere le unità stratigrafiche murarie e negli aspetti estetici delle superfici stesse. Dal momento però che i muri fanno parte delle strutture portanti più importanti, non si può parlare di tecniche murarie senza cercare di capire come i vari tipi classificati si comportino realmente dal punto di vista statico. Si cerca perciò di verificare e in qualche modo di capire l’intero volume di ogni tecnica muraria, e se vi siano della regole generali o particolari che siano in qualche modo deducibili anche dalle superfici visibili. Si propone infine una classificazione delle «famiglie» di tecniche murarie più note sulla base dei loro sistemi costruttivi e funzionali, oltre che formali.

  16. Ricerca di produzione associata con dark matter

    CERN Document Server

    Valerio Ippolito

    2016-01-01

    Among the experimental strategies for the search for Dark Matter, collider experiments provideunique sensitivity to its non-gravitational interactions with ordinary matter, for a range of DarkMatter masses between a few GeV and hundreds of GeV. We discuss the status of the main DarkMatter searches at the Large Hadron Collider by the ATLAS and CMS experiments, underliningthe complementarity between searches in different final states and between collider and directdetection results.

  17. Biomass CHP Catalog of Technologies

    Science.gov (United States)

    This report reviews the technical and economic characterization of biomass resources, biomass preparation, energy conversion technologies, power production systems, and complete integrated CHP systems.

  18. Biomass Carbon Stock

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — Biomass carbon includes carbon stored in above- and below-ground live plant components (such as leaf, branch, stem and root) as well as in standing and down dead...

  19. Biomass_Master

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Biomass data found in this data set are broken into four regions of the Northeast US Continental Shelf Large Marine Ecosystem: Gulf of Maine, Georges Bank,...

  20. Hydrothermal liquefaction of biomass

    DEFF Research Database (Denmark)

    Toor, Saqib; Rosendahl, Lasse; Hoffmann, Jessica

    2014-01-01

    Biomass is one of the most abundant sources of renewable energy, and will be an important part of a more sustainable future energy system. In addition to direct combustion, there is growing attention on conversion of biomass into liquid en-ergy carriers. These conversion methods are divided...... into liquid biofuels, with the aim of describing the current status and development challenges of the technology. During the hydrothermal liquefaction process, the biomass macromolecules are first hydrolyzed and/or degraded into smaller molecules. Many of the produced molecules are unstable and reactive...... into biochemical/biotechnical methods and thermochemical methods; such as direct combustion, pyrolysis, gasification, liquefaction etc. This chapter will focus on hydrothermal liquefaction, where high pressures and intermediate temperatures together with the presence of water are used to convert biomass...

  1. Biomass for bioenergy

    DEFF Research Database (Denmark)

    Bentsen, Niclas Scott

    for displacing fossil resources and is perceived as one of the main pillars of a future low-carbon or no-carbon energy supply. However, biomass, renewable as it is, is for any relevant, time horizon to be considered a finite resource as it replenishes at a finite rate. Conscientious stewardship of this finite......Across the range of renewable energy resources, bioenergy is probably the most complex, as using biomass to support energy services ties into a number of fields; climate change, food production, rural development, biodiversity and environmental protection. Biomass offer several options...... the undesirable impacts of bioenergy done wrong. However, doing bioenergy right is a significant challenge due to the ties into other fields of society. Fundamentally plant biomass is temporary storage of solar radiation energy and chemically bound energy from nutrients. Bioenergy is a tool to harness solar...

  2. Hydrothermal liquefaction of biomass

    DEFF Research Database (Denmark)

    Toor, Saqib; Rosendahl, Lasse; Hoffmann, Jessica

    2014-01-01

    Biomass is one of the most abundant sources of renewable energy, and will be an important part of a more sustainable future energy system. In addition to direct combustion, there is growing attention on conversion of biomass into liquid en-ergy carriers. These conversion methods are divided...... into biochemical/biotechnical methods and thermochemical methods; such as direct combustion, pyrolysis, gasification, liquefaction etc. This chapter will focus on hydrothermal liquefaction, where high pressures and intermediate temperatures together with the presence of water are used to convert biomass...... into liquid biofuels, with the aim of describing the current status and development challenges of the technology. During the hydrothermal liquefaction process, the biomass macromolecules are first hydrolyzed and/or degraded into smaller molecules. Many of the produced molecules are unstable and reactive...

  3. 2007 Biomass Program Overview

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2009-10-27

    The Biomass Program is actively working with public and private partners to meet production and technology needs. With the corn ethanol market growing steadily, researchers are unlocking the potential of non-food biomass sources, such as switchgrass and forest and agricultural residues. In this way, the Program is helping to ensure that cost-effective technologies will be ready to support production goals for advanced biofuels.

  4. Biomass feedstock analyses

    Energy Technology Data Exchange (ETDEWEB)

    Wilen, C.; Moilanen, A.; Kurkela, E. [VTT Energy, Espoo (Finland). Energy Production Technologies

    1996-12-31

    The overall objectives of the project `Feasibility of electricity production from biomass by pressurized gasification systems` within the EC Research Programme JOULE II were to evaluate the potential of advanced power production systems based on biomass gasification and to study the technical and economic feasibility of these new processes with different type of biomass feed stocks. This report was prepared as part of this R and D project. The objectives of this task were to perform fuel analyses of potential woody and herbaceous biomasses with specific regard to the gasification properties of the selected feed stocks. The analyses of 15 Scandinavian and European biomass feed stock included density, proximate and ultimate analyses, trace compounds, ash composition and fusion behaviour in oxidizing and reducing atmospheres. The wood-derived fuels, such as whole-tree chips, forest residues, bark and to some extent willow, can be expected to have good gasification properties. Difficulties caused by ash fusion and sintering in straw combustion and gasification are generally known. The ash and alkali metal contents of the European biomasses harvested in Italy resembled those of the Nordic straws, and it is expected that they behave to a great extent as straw in gasification. Any direct relation between the ash fusion behavior (determined according to the standard method) and, for instance, the alkali metal content was not found in the laboratory determinations. A more profound characterisation of the fuels would require gasification experiments in a thermobalance and a PDU (Process development Unit) rig. (orig.) (10 refs.)

  5. Northeast Regional Biomass Program

    Energy Technology Data Exchange (ETDEWEB)

    Lusk, P.D.

    1992-12-01

    The Northeast Regional Biomass Program has been in operation for a period of nine years. During this time, state managed programs and technical programs have been conducted covering a wide range of activities primarily aim at the use and applications of wood as a fuel. These activities include: assessments of available biomass resources; surveys to determine what industries, businesses, institutions, and utility companies use wood and wood waste for fuel; and workshops, seminars, and demonstrations to provide technical assistance. In the Northeast, an estimated 6.2 million tons of wood are used in the commercial and industrial sector, where 12.5 million cords are used for residential heating annually. Of this useage, 1504.7 mw of power has been generated from biomass. The use of wood energy products has had substantial employment and income benefits in the region. Although wood and woodwaste have received primary emphasis in the regional program, the use of municipal solid waste has received increased emphasis as an energy source. The energy contribution of biomass will increase as potentia users become more familiar with existing feedstocks, technologies, and applications. The Northeast Regional Biomass Program is designed to support region-specific to overcome near-term barriers to biomass energy use.

  6. Aerosols from biomass combustion

    Energy Technology Data Exchange (ETDEWEB)

    Nussbaumer, T.

    2001-07-01

    This report is the proceedings of a seminar on biomass combustion and aerosol production organised jointly by the International Energy Agency's (IEA) Task 32 on bio energy and the Swiss Federal Office of Energy (SFOE). This collection of 16 papers discusses the production of aerosols and fine particles by the burning of biomass and their effects. Expert knowledge on the environmental impact of aerosols, formation mechanisms, measurement technologies, methods of analysis and measures to be taken to reduce such emissions is presented. The seminar, visited by 50 participants from 11 countries, shows, according to the authors, that the reduction of aerosol emissions resulting from biomass combustion will remain a challenge for the future.

  7. Biomass for bioenergy

    DEFF Research Database (Denmark)

    Bentsen, Niclas Scott

    Across the range of renewable energy resources, bioenergy is probably the most complex, as using biomass to support energy services ties into a number of fields; climate change, food production, rural development, biodiversity and environmental protection. Biomass offer several options...... for displacing fossil resources and is perceived as one of the main pillars of a future low-carbon or no-carbon energy supply. However, biomass, renewable as it is, is for any relevant, time horizon to be considered a finite resource as it replenishes at a finite rate. Conscientious stewardship of this finite...... resource requires not only disciplined research, but also a multidisciplinary approach in the development of viable solutions. It has been suggested that society can neither afford to miss out on global climate change mitigation and local development offered by bioenergy done right nor accept...

  8. YEAR 2 BIOMASS UTILIZATION

    Energy Technology Data Exchange (ETDEWEB)

    Christopher J. Zygarlicke

    2004-11-01

    This Energy & Environmental Research Center (EERC) Year 2 Biomass Utilization Final Technical Report summarizes multiple projects in biopower or bioenergy, transportation biofuels, and bioproducts. A prototype of a novel advanced power system, termed the high-temperature air furnace (HITAF), was tested for performance while converting biomass and coal blends to energy. Three biomass fuels--wood residue or hog fuel, corn stover, and switchgrass--and Wyoming subbituminous coal were acquired for combustion tests in the 3-million-Btu/hr system. Blend levels were 20% biomass--80% coal on a heat basis. Hog fuel was prepared for the upcoming combustion test by air-drying and processing through a hammer mill and screen. A K-Tron biomass feeder capable of operating in both gravimetric and volumetric modes was selected as the HITAF feed system. Two oxide dispersion-strengthened (ODS) alloys that would be used in the HITAF high-temperature heat exchanger were tested for slag corrosion rates. An alumina layer formed on one particular alloy, which was more corrosion-resistant than a chromia layer that formed on the other alloy. Research activities were completed in the development of an atmospheric pressure, fluidized-bed pyrolysis-type system called the controlled spontaneous reactor (CSR), which is used to process and condition biomass. Tree trimmings were physically and chemically altered by the CSR process, resulting in a fuel that was very suitable for feeding into a coal combustion or gasification system with little or no feed system modifications required. Experimental procedures were successful for producing hydrogen from biomass using the bacteria Thermotoga, a deep-ocean thermal vent organism. Analytical procedures for hydrogen were evaluated, a gas chromatography (GC) method was derived for measuring hydrogen yields, and adaptation culturing and protocols for mutagenesis were initiated to better develop strains that can use biomass cellulose. Fly ash derived from

  9. YEAR 2 BIOMASS UTILIZATION

    Energy Technology Data Exchange (ETDEWEB)

    Christopher J. Zygarlicke

    2004-11-01

    This Energy & Environmental Research Center (EERC) Year 2 Biomass Utilization Final Technical Report summarizes multiple projects in biopower or bioenergy, transportation biofuels, and bioproducts. A prototype of a novel advanced power system, termed the high-temperature air furnace (HITAF), was tested for performance while converting biomass and coal blends to energy. Three biomass fuels--wood residue or hog fuel, corn stover, and switchgrass--and Wyoming subbituminous coal were acquired for combustion tests in the 3-million-Btu/hr system. Blend levels were 20% biomass--80% coal on a heat basis. Hog fuel was prepared for the upcoming combustion test by air-drying and processing through a hammer mill and screen. A K-Tron biomass feeder capable of operating in both gravimetric and volumetric modes was selected as the HITAF feed system. Two oxide dispersion-strengthened (ODS) alloys that would be used in the HITAF high-temperature heat exchanger were tested for slag corrosion rates. An alumina layer formed on one particular alloy, which was more corrosion-resistant than a chromia layer that formed on the other alloy. Research activities were completed in the development of an atmospheric pressure, fluidized-bed pyrolysis-type system called the controlled spontaneous reactor (CSR), which is used to process and condition biomass. Tree trimmings were physically and chemically altered by the CSR process, resulting in a fuel that was very suitable for feeding into a coal combustion or gasification system with little or no feed system modifications required. Experimental procedures were successful for producing hydrogen from biomass using the bacteria Thermotoga, a deep-ocean thermal vent organism. Analytical procedures for hydrogen were evaluated, a gas chromatography (GC) method was derived for measuring hydrogen yields, and adaptation culturing and protocols for mutagenesis were initiated to better develop strains that can use biomass cellulose. Fly ash derived from

  10. Biomass co-firing

    DEFF Research Database (Denmark)

    Yin, Chungen

    2013-01-01

    Co-firing biomass with fossil fuels in existing power plants is an attractive option for significantly increasing renewable energy resource utilization and reducing CO2 emissions. This chapter mainly discusses three direct co-firing technologies: pulverized-fuel (PF) boilers, fluidized-bed combus......Co-firing biomass with fossil fuels in existing power plants is an attractive option for significantly increasing renewable energy resource utilization and reducing CO2 emissions. This chapter mainly discusses three direct co-firing technologies: pulverized-fuel (PF) boilers, fluidized......-bed combustion (FBC) systems, and grate-firing systems, which are employed in about 50%, 40% and 10% of all the co-firing plants, respectively. Their basic principles, process technologies, advantages, and limitations are presented, followed by a brief comparison of these technologies when applied to biomass co...

  11. Sustainable Biomass Supply Systems

    Energy Technology Data Exchange (ETDEWEB)

    Erin Searcy; Dave Muth; Erin Wilkerson; Shahab Sokansanj; Bryan Jenkins; Peter Titman; Nathan Parker; Quinn Hart; Richard Nelson

    2009-04-01

    The U.S. Department of Energy (DOE) aims to displace 30% of the 2004 gasoline use (60 billion gal/yr) with biofuels by 2030 as outlined in the Energy Independence and Security Act of 2007, which will require 700 million tons of biomass to be sustainably delivered to biorefineries annually. Lignocellulosic biomass will make an important contribution towards meeting DOE’s ethanol production goals. For the biofuels industry to be an economically viable enterprise, the feedstock supply system (i.e., moving the biomass from the field to the refinery) cannot contribute more that 30% of the total cost of the biofuel production. The Idaho National Laboratory in collaboration with Oak Ridge National Laboratory, University of California, Davis and Kansas State University are developing a set of tools for identifying economical, sustainable feedstocks on a regional basis based on biorefinery siting.

  12. Biomass co-firing

    DEFF Research Database (Denmark)

    Yin, Chungen

    2013-01-01

    Co-firing biomass with fossil fuels in existing power plants is an attractive option for significantly increasing renewable energy resource utilization and reducing CO2 emissions. This chapter mainly discusses three direct co-firing technologies: pulverized-fuel (PF) boilers, fluidized-bed combus......Co-firing biomass with fossil fuels in existing power plants is an attractive option for significantly increasing renewable energy resource utilization and reducing CO2 emissions. This chapter mainly discusses three direct co-firing technologies: pulverized-fuel (PF) boilers, fluidized......-bed combustion (FBC) systems, and grate-firing systems, which are employed in about 50%, 40% and 10% of all the co-firing plants, respectively. Their basic principles, process technologies, advantages, and limitations are presented, followed by a brief comparison of these technologies when applied to biomass co...

  13. SERI Biomass Program

    Science.gov (United States)

    Bergeron, P. W.; Corder, R. E.; Hill, A. M.; Lindsey, H.; Lowenstein, M. Z.

    1983-02-01

    The biomass with which this report is concerned includes aquatic plants, which can be converted into liquid fuels and chemicals; organic wastes (crop residues as well as animal and municipal wastes), from which biogas can be produced via anerobic digestion; and organic or inorganic waste streams, from which hydrogen can be produced by photobiological processes. The Biomass Program Office supports research in three areas which, although distinct, all use living organisms to create the desired products. The Aquatic Species Program (ASP) supports research on organisms that are themselves processed into the final products, while the Anaerobic Digestion (ADP) and Photo/Biological Hydrogen Program (P/BHP) deals with organisms that transform waste streams into energy products. The P/BHP is also investigating systems using water as a feedstock and cell-free systems which do not utilize living organisms. This report summarizes the progress and research accomplishments of the SERI Biomass Program during FY 1982.

  14. Biomass stoves in dwellings

    DEFF Research Database (Denmark)

    Luis Teles de Carvalho, Ricardo

    and analyzed in this session. Experimental results regarding the performance of biomass combustion stoves and the effects of real-life practices in terms of thermal efficiency, particulate and gaseous emissions will be addressed. This research is based on the development of a new testing approach that combines...... laboratory and field measurements established in the context of the implications of the upcoming eco-design directive. The communication will cover technical aspects concerning the operating performance of different types of biomass stoves and building envelopes, in order to map the ongoing opportunities...

  15. Method for pretreating lignocellulosic biomass

    Science.gov (United States)

    Kuzhiyil, Najeeb M.; Brown, Robert C.; Dalluge, Dustin Lee

    2015-08-18

    The present invention relates to a method for pretreating lignocellulosic biomass containing alkali and/or alkaline earth metal (AAEM). The method comprises providing a lignocellulosic biomass containing AAEM; determining the amount of the AAEM present in the lignocellulosic biomass; identifying, based on said determining, the amount of a mineral acid sufficient to completely convert the AAEM in the lignocellulosic biomass to thermally-stable, catalytically-inert salts; and treating the lignocellulosic biomass with the identified amount of the mineral acid, wherein the treated lignocellulosic biomass contains thermally-stable, catalytically inert AAEM salts.

  16. Biomass Deconstruction and Recalcitrance

    DEFF Research Database (Denmark)

    Zhang, Heng

    system, a plate incubator and a high performance liquid chromatography (HPLC) system. In comparison with the reported HTS platforms, the Copenhagen platform is featured by the fully automatic biomass sample preparation system, the bench-scale hydrothermal pretreatment setup, and precise sugar measurement...

  17. Biomass Conversion Factsheet

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-06-05

    To efficiently convert algae, diverse types of cellulosic biomass, and emerging feedstocks into renewable fuels, the U.S. Department of Energy (DOE) supports research, development, and demonstration of technologies. This research will help ensure that these renewable fuels are compatible with today’s vehicles and infrastructure.

  18. Pyrolysis of chitin biomass

    DEFF Research Database (Denmark)

    Qiao, Yan; Chen, Shuai; Liu, Ying

    2015-01-01

    The thermal degradation of chitin biomass with various molecular structures was investigated by thermogravimetric analysis (TG), and the gaseous products were analyzed by connected mass spectroscopy (MS). The chemical structure and morphology of char residues collected at 750°C using the model...

  19. Switchgrass for biomass energy

    Science.gov (United States)

    Switchgrass (Panicum virgatum) is a native warm-season grass and is the model herbaceous perennial biomass energy feedstock for the USA. More than 75-years of experience confirm that switchgrass will be productive and sustainable on rain-fed marginally-productive cropland east of the 100th meridian....

  20. Platform chemicals from biomass

    NARCIS (Netherlands)

    Rasrendra, Carolus Borromeus

    2012-01-01

    Hoogwaardige chemicaliën uit houtafval De ontwikkeling van nieuwe routes voor (bulk)chemicaliën uit biomassa is van groot belang voor toekomstige biobased societies. In dit proefschrift worden katalytische routes beschreven voor platformchemicaliën uit de suikerfractie van lignocellulosische biomass

  1. Biomass Scenario Model

    Energy Technology Data Exchange (ETDEWEB)

    2015-09-01

    The Biomass Scenario Model (BSM) is a unique, carefully validated, state-of-the-art dynamic model of the domestic biofuels supply chain which explicitly focuses on policy issues, their feasibility, and potential side effects. It integrates resource availability, physical/technological/economic constraints, behavior, and policy. The model uses a system dynamics simulation (not optimization) to model dynamic interactions across the supply chain.

  2. Marine biomass research advances

    Energy Technology Data Exchange (ETDEWEB)

    Bender, E.

    1980-08-01

    This paper reports on research in California, New York and elsewhere into marine biomass. A manmade marine farm moored four miles off the coast of southern California pumps deep water up a 450 m pipe to fertilize giant kelp. After harvesting and chopping by existing commercial methods, the kelp would be converted, by either anaerobic bacteria or thermal processes, into methane and other products.

  3. Carbon Fiber from Biomass

    Energy Technology Data Exchange (ETDEWEB)

    Milbrandt, Anelia [Clean Energy Manufacturing Analysis Center, Godlen, CO (United States); Booth, Samuel [Clean Energy Manufacturing Analysis Center, Godlen, CO (United States)

    2016-09-01

    Carbon fiber (CF), known also as graphite fiber, is a lightweight, strong, and flexible material used in both structural (load-bearing) and non-structural applications (e.g., thermal insulation). The high cost of precursors (the starting material used to make CF, which comes predominately from fossil sources) and manufacturing have kept CF a niche market with applications limited mostly to high-performance structural materials (e.g., aerospace). Alternative precursors to reduce CF cost and dependence on fossil sources have been investigated over the years, including biomass-derived precursors such as rayon, lignin, glycerol, and lignocellulosic sugars. The purpose of this study is to provide a comprehensive overview of CF precursors from biomass and their market potential. We examine the potential CF production from these precursors, the state of technology and applications, and the production cost (when data are available). We discuss their advantages and limitations. We also discuss the physical properties of biomass-based CF, and we compare them to those of polyacrylonitrile (PAN)-based CF. We also discuss manufacturing and end-product considerations for bio-based CF, as well as considerations for plant siting and biomass feedstock logistics, feedstock competition, and risk mitigation strategies. The main contribution of this study is that it provides detailed technical and market information about each bio-based CF precursor in one document while other studies focus on one precursor at a time or a particular topic (e.g., processing). Thus, this publication allows for a comprehensive view of the CF potential from all biomass sources and serves as a reference for both novice and experienced professionals interested in CF production from alternative sources.

  4. Enzymes for improved biomass conversion

    Science.gov (United States)

    Brunecky, Roman; Himmel, Michael E.

    2016-02-02

    Disclosed herein are enzymes and combinations of the enzymes useful for the hydrolysis of cellulose and the conversion of biomass. Methods of degrading cellulose and biomass using enzymes and cocktails of enzymes are also disclosed.

  5. Enzymes for improved biomass conversion

    Energy Technology Data Exchange (ETDEWEB)

    Brunecky, Roman; Himmel, Michael E.

    2016-02-02

    Disclosed herein are enzymes and combinations of the enzymes useful for the hydrolysis of cellulose and the conversion of biomass. Methods of degrading cellulose and biomass using enzymes and cocktails of enzymes are also disclosed.

  6. Biomass Feedstock National User Facility

    Data.gov (United States)

    Federal Laboratory Consortium — Bioenergy research at the Biomass Feedstock National User Facility (BFNUF) is focused on creating commodity-scale feed-stocks from native biomass that meet the needs...

  7. Multi-functional biomass systems

    NARCIS (Netherlands)

    Dornburg, Veronika

    2004-01-01

    Biomass can play a role in mitigating greenhouse gas emissions by substituting conventional materials and supplying biomass based fuels. Main reason for the low share of biomass applications in Europe is their often-high production costs, among others due to the relatively low availability of

  8. Biomass gasification in the Netherlands

    Energy Technology Data Exchange (ETDEWEB)

    Van der Drift, A. [ECN Biomass and Energy Efficiency, Petten (Netherlands)

    2013-07-15

    This reports summarizes the activities, industries, and plants on biomass gasification in the Netherlands. Most of the initiatives somehow relate to waste streams, rather than clean biomass, which may seem logic for a densely populated country as the Netherlands. Furthermore, there is an increasing interest for the production of SNG (Substitute Natural Gas) from biomass, both from governments and industry.

  9. High Pressure Biomass Gasification

    Energy Technology Data Exchange (ETDEWEB)

    Agrawal, Pradeep K [Georgia Tech Research Corporation, Atlanta, GA (United States)

    2016-07-29

    According to the Billion Ton Report, the U.S. has a large supply of biomass available that can supplement fossil fuels for producing chemicals and transportation fuels. Agricultural waste, forest residue, and energy crops offer potential benefits: renewable feedstock, zero to low CO2 emissions depending on the specific source, and domestic supply availability. Biomass can be converted into chemicals and fuels using one of several approaches: (i) biological platform converts corn into ethanol by using depolymerization of cellulose to form sugars followed by fermentation, (ii) low-temperature pyrolysis to obtain bio-oils which must be treated to reduce oxygen content via HDO hydrodeoxygenation), and (iii) high temperature pyrolysis to produce syngas (CO + H2). This last approach consists of producing syngas using the thermal platform which can be used to produce a variety of chemicals and fuels. The goal of this project was to develop an improved understanding of the gasification of biomass at high pressure conditions and how various gasification parameters might affect the gasification behavior. Since most downstream applications of synags conversion (e.g., alcohol synthesis, Fischer-Tropsch synthesis etc) involve utilizing high pressure catalytic processes, there is an interest in carrying out the biomass gasification at high pressure which can potentially reduce the gasifier size and subsequent downstream cleaning processes. It is traditionally accepted that high pressure should increase the gasification rates (kinetic effect). There is also precedence from coal gasification literature from the 1970s that high pressure gasification would be a beneficial route to consider. Traditional approach of using thermogravimetric analyzer (TGA) or high-pressure themogravimetric analyzer (PTGA) worked well in understanding the gasification kinetics of coal gasification which was useful in designing high pressure coal gasification processes. However

  10. Biomass to energy; La valorisation energetique de la biomasse

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-06-15

    This road-map proposes by the Group Total aims to inform the public on the biomass to energy. It explains the biomass principle, the possibility of biomass to energy conversion, the first generation of biofuels (bio ethanol, ETBE, bio diesel, flex fuel) and their advantages and limitations, the european regulatory framework and policy with the evolutions and Total commitments in the domain. (A.L.B.)

  11. Biomass process handbook

    Energy Technology Data Exchange (ETDEWEB)

    1983-01-01

    Descriptions are given of 42 processes which use biomass to produce chemical products. Marketing and economic background, process description, flow sheets, costs, major equipment, and availability of technology are given for each of the 42 processes. Some of the chemicals discussed are: ethanol, ethylene, acetaldehyde, butanol, butadiene, acetone, citric acid, gluconates, itaconic acid, lactic acid, xanthan gum, sorbitol, starch polymers, fatty acids, fatty alcohols, glycerol, soap, azelaic acid, perlargonic acid, nylon-11, jojoba oil, furfural, furfural alcohol, tetrahydrofuran, cellulose polymers, products from pulping wastes, and methane. Processes include acid hydrolysis, enzymatic hydrolysis, fermentation, distillation, Purox process, and anaerobic digestion.

  12. Biomass Energy Generation Project

    Energy Technology Data Exchange (ETDEWEB)

    Olthoff, Edward [Cedar Falls Utilities, Cedar Falls, IA (United States)

    2017-05-15

    The Municipal Electric Utility of the City of Cedar Falls (dba Cedar Fals Utilities or CFU) received a congressionally directed grant funded through DOE-EERE to run three short (4 hour) duration test burns and one long (10 days) duration test burn to test the viability of renewable fuels in Streeter Station Boiler #6, a stoker coal fired electric generation unit. The long test burn was intended to test supply chain assumptions, optimize boiler combustion and assess the effects of a longer duration burn of biomass on the boiler.

  13. Biomass Deconstruction and Recalcitrance

    DEFF Research Database (Denmark)

    Zhang, Heng

    reflections of plant species, tissue or organ types, genetic traits and environment. Effects of cultivar type, anatomical distribution, chemical composition, fertilizer level and growth year have been observed during in vitro and in vivo trials. A similar approach is here taken to further investigate: 1). How...... system, a plate incubator and a high performance liquid chromatography (HPLC) system. In comparison with the reported HTS platforms, the Copenhagen platform is featured by the fully automatic biomass sample preparation system, the bench-scale hydrothermal pretreatment setup, and precise sugar measurement...

  14. Entrained Flow Gasification of Biomass

    DEFF Research Database (Denmark)

    Qin, Ke

    of different fuels on syngas products was investigated at 1400 °C with steam addition. The yields of residual particulates (char and/or soot) decreased with increasing straw fraction during straw/wood co-gasification and with increasing biomass fraction (straw or wood) during biomass/coal co......, char-gas and soot-gas reactions, detailed gas-phase reactions, and mass and heat transfer. The model could reasonable predict the yields of syngas products obtained in the biomass gasification experiments. Moreover, the simulation results suggest that the soot can be completely converted and thereby......The present Ph. D. thesis describes experimental and modeling investigations on entrained flow gasification of biomass and an experimental investigation on entrained flow cogasification of biomass and coal. A review of the current knowledge of biomass entrained flow gasification is presented...

  15. Enrichment of cadmium in biomasses

    Energy Technology Data Exchange (ETDEWEB)

    Gwenner, C.; Wittig, H.; Glombitza, F.

    1986-01-01

    The uptake of cadmium ions from an aqueous solution by living, resting, and dead biomasses was investigated. The dependence of the uptaked amounts on pH-value of the medium, temperature and concentration of cadmium ions is demonstrated as well as the rate of uptake. Maximum realisable concentrations were 12 mg/g biomass in living cells and about 20 mg/g biomass in resting or dead cells, respectively.

  16. Energy Recovery from Contaminated Biomass

    Directory of Open Access Journals (Sweden)

    Jiří Moskalík

    2012-01-01

    Full Text Available This study focuses on thermal gasification methods of contaminated biomass in an atmospheric fluidized bed, especially biomass contaminated by undesirable substances in its primary use. For the experiments, chipboard waste was chosen as a representative sample of contaminated biomass. In the experiments, samples of gas and tar were taken for a better description of the process of gasifying chipboard waste. Gas and tar samples also provide information about the properties of the gas that is produced.

  17. PHA recovery from biomass.

    Science.gov (United States)

    Madkour, Mohamed H; Heinrich, Daniel; Alghamdi, Mansour A; Shabbaj, Ibraheem I; Steinbüchel, Alexander

    2013-09-09

    The recovery of polyhydroxyalkanoates (PHAs) from biomass, that is, from bacterial cells, is one of the major obstacles in the industrial production of these polyesters. Since PHAs are naturally synthesized as intracellular storage compounds for carbon and energy and are for this deposited in the cytoplasm of the bacterial cell, PHAs are more or less tightly linked with the entire biomass, and the polyesters must be released from the cells before their isolation and purification can be conducted. This additional step, that is, the release from the cells, is a major difference from most other biotechnological processes where the product occurs outside of the cells because it is secreted into the medium in a bioreactor or because it is synthesized in vitro in an enzyme reactor in a cell free system. This additional step contributes significantly to the overall costs of production. In this review we provide an overview about the different processes that result in the release of PHA from the cells, and we evaluate these processes with regard to the suitability at large scale in the industry.

  18. Regulation possibilities of biomass combustion

    Science.gov (United States)

    Suzdalenko, Vera; Gedrovics, Martins; Zake, Maija; Barmina, Inesa

    2012-11-01

    The focus of the recent experimental research is to analyze the regulation possibilities of biomass combustion. Three possibilities were chosen as part of this research: a) biomass cofiring with propane, b) swirling flow with re-circulation zone, and c) use of a permanent magnet. The aim of the research is to provide stable, controllable and effective biomass combustion with minimum emissions. The special pilot device was created where biomass can be combusted separately and co-fired with propane. Wood pellets were used during the experiments.

  19. Biomass Rapid Analysis Network (BRAN)

    Energy Technology Data Exchange (ETDEWEB)

    2003-10-01

    Helping the emerging biotechnology industry develop new tools and methods for real-time analysis of biomass feedstocks, process intermediates and The Biomass Rapid Analysis Network is designed to fast track the development of modern tools and methods for biomass analysis to accelerate the development of the emerging industry. The network will be led by industry and organized and coordinated through the National Renewable Energy Lab. The network will provide training and other activities of interest to BRAN members. BRAN members will share the cost and work of rapid analysis method development, validate the new methods, and work together to develop the training for the future biomass conversion workforce.

  20. Modelling tree biomasses in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Repola, J.

    2013-06-01

    Biomass equations for above- and below-ground tree components of Scots pine (Pinus sylvestris L), Norway spruce (Picea abies [L.] Karst) and birch (Betula pendula Roth and Betula pubescens Ehrh.) were compiled using empirical material from a total of 102 stands. These stands (44 Scots pine, 34 Norway spruce and 24 birch stands) were located mainly on mineral soil sites representing a large part of Finland. The biomass models were based on data measured from 1648 sample trees, comprising 908 pine, 613 spruce and 127 birch trees. Biomass equations were derived for the total above-ground biomass and for the individual tree components: stem wood, stem bark, living and dead branches, needles, stump, and roots, as dependent variables. Three multivariate models with different numbers of independent variables for above-ground biomass and one for below-ground biomass were constructed. Variables that are normally measured in forest inventories were used as independent variables. The simplest model formulations, multivariate models (1) were mainly based on tree diameter and height as independent variables. In more elaborated multivariate models, (2) and (3), additional commonly measured tree variables such as age, crown length, bark thickness and radial growth rate were added. Tree biomass modelling includes consecutive phases, which cause unreliability in the prediction of biomass. First, biomasses of sample trees should be determined reliably to decrease the statistical errors caused by sub-sampling. In this study, methods to improve the accuracy of stem biomass estimates of the sample trees were developed. In addition, the reliability of the method applied to estimate sample-tree crown biomass was tested, and no systematic error was detected. Second, the whole information content of data should be utilized in order to achieve reliable parameter estimates and applicable and flexible model structure. In the modelling approach, the basic assumption was that the biomasses of

  1. Vegetal and animal biomass; Les biomasses vegetales et animales

    Energy Technology Data Exchange (ETDEWEB)

    Combarnous, M. [Bordeaux-1 Univ., Lab. Energetique et Phenomenes de Transfert, UMR CNRS ENSAM, 33 - Talence (France)

    2005-07-01

    This presentation concerns all types of biomass of the earth and the seas and the relative implicit consumptions. After an evaluation of the food needs of the human being, the author discusses the solar energy conversion, the energetic flux devoted to the agriculture production, the food chain and the biomass. (A.L.B.)

  2. System and process for biomass treatment

    Science.gov (United States)

    Dunson, Jr., James B; Tucker, III, Melvin P; Elander, Richard T; Lyons, Robert C

    2013-08-20

    A system including an apparatus is presented for treatment of biomass that allows successful biomass treatment at a high solids dry weight of biomass in the biomass mixture. The design of the system provides extensive distribution of a reactant by spreading the reactant over the biomass as the reactant is introduced through an injection lance, while the biomass is rotated using baffles. The apparatus system to provide extensive assimilation of the reactant into biomass using baffles to lift and drop the biomass, as well as attrition media which fall onto the biomass, to enhance the treatment process.

  3. ALTENER - Biomass event in Finland

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The publication contains the lectures held in the Biomass event in Finland. The event was divided into two sessions: Fuel production and handling, and Co-combustion and gasification sessions. Both sessions consisted of lectures and the business forum during which the companies involved in the research presented themselves and their research and their equipment. The fuel production and handling session consisted of following lectures and business presentations: AFB-NETT - business opportunities for European biomass industry; Wood waste in Europe; Wood fuel production technologies in EU- countries; new drying method for wood waste; Pellet - the best package for biofuel - a view from the Swedish pelletmarket; First biomass plant in Portugal with forest residue fuel; and the business forum of presentations: Swedish experiences of willow growing; Biomass handling technology; Chipset 536 C Harvester; KIC International. The Co-combustion and gasification session consisted of following lectures and presentations: Gasification technology - overview; Overview of co-combustion technology in Europe; Modern biomass combustion technology; Wood waste, peat and sludge combustion in Enso Kemi mills and UPM-Kymmene Rauma paper mill; Enhanced CFB combustion of wood chips, wood waste and straw in Vaexjoe in Sweden and Grenaa CHP plant in Denmark; Co-combustion of wood waste; Biomass gasification projects in India and Finland; Biomass CFB gasifier connected to a 350 MW{sub t}h steam boiler fired with coal and natural gas - THERMIE demonstration project in Lahti (FI); Biomass gasification for energy production, Noord Holland plant in Netherlands and Arbre Energy (UK); Gasification of biomass in fixed bed gasifiers, Wet cleaning and condensing heat recovery of flue gases; Combustion of wet biomass by underfeed grate boiler; Research on biomass and waste for energy; Engineering and consulting on energy (saving) projects; and Research and development on combustion of solid fuels

  4. Mobile Biomass Pelletizing System

    Energy Technology Data Exchange (ETDEWEB)

    Thomas Mason

    2009-04-16

    This grant project examines multiple aspects of the pelletizing process to determine the feasibility of pelletizing biomass using a mobile form factor system. These aspects are: the automatic adjustment of the die height in a rotary-style pellet mill, the construction of the die head to allow the use of ceramic materials for extreme wear, integrating a heat exchanger network into the entire process from drying to cooling, the use of superheated steam for adjusting the moisture content to optimum, the economics of using diesel power to operate the system; a break-even analysis of estimated fixed operating costs vs. tons per hour capacity. Initial development work has created a viable mechanical model. The overall analysis of this model suggests that pelletizing can be economically done using a mobile platform.

  5. Biomass plantations - energy farming

    Energy Technology Data Exchange (ETDEWEB)

    Paul, S.

    1981-02-01

    Mounting oil import bills in India are restricting her development programmes by forcing the cutting down of the import of other essential items. But the countries of the tropics have abundant sunlight and vast tracts of arable wastelands. Energy farming is proposed in the shape of energy plantations through forestry or energy cropping through agricultural media, to provide power fuels for transport and the industries and also to provide fuelwoods for the domestic sector. Short rotation cultivation is discussed and results are given of two main species that are being tried, ipil-ipil and Casuarina. Evaluations are made on the use of various crops such as sugar cane, cassava and kenaf as fuel crops together with hydrocarbon plants and aquatic biomass. (Refs. 20)

  6. Refining fast pyrolysis of biomass

    NARCIS (Netherlands)

    Westerhof, Roel Johannes Maria

    2011-01-01

    Pyrolysis oil produced from biomass is a promising renewable alternative to crude oil. Such pyrolysis oil has transportation, storage, and processing benefits, none of which are offered by the bulky, inhomogeneous solid biomass from which it originates. However, pyrolysis oil has both a different

  7. Woody biomass logistics [Chapter 14

    Science.gov (United States)

    Robert Keefe; Nathaniel Anderson; John Hogland; Ken Muhlenfeld

    2014-01-01

    The economics of using woody biomass as a fuel or feedstock for bioenergy applications is often driven by logistical considerations. Depending on the source of the woody biomass, the acquisition cost of the material is often quite low, sometimes near zero. However, the cost of harvesting, collection, processing, storage, and transportation from the harvest site to end...

  8. Forest biomass-based energy

    Science.gov (United States)

    Janaki R. R. Alavalapati; Pankaj Lal; Andres Susaeta; Robert C. Abt; David N. Wear

    2013-01-01

    Key FindingsHarvesting woody biomass for use as bioenergy is projected to range from 170 million to 336 million green tons by 2050, an increase of 54 to 113 percent over current levels.Consumption projections for forest biomass-based energy, which are based on Energy Information Administration projections, have a high level of...

  9. Refining fast pyrolysis of biomass

    NARCIS (Netherlands)

    Westerhof, Roel Johannes Maria

    2011-01-01

    Pyrolysis oil produced from biomass is a promising renewable alternative to crude oil. Such pyrolysis oil has transportation, storage, and processing benefits, none of which are offered by the bulky, inhomogeneous solid biomass from which it originates. However, pyrolysis oil has both a different co

  10. Fundamentals of Biomass pellet production

    DEFF Research Database (Denmark)

    Holm, Jens Kai; Henriksen, Ulrik Birk; Hustad, Johan Einar

    2005-01-01

    Pelletizing experiments along with modelling of the pelletizing process have been carried out with the aim of understanding the fundamental physico-chemical mechanisms that control the quality and durability of biomass pellets. A small-scale California pellet mill (25 kg/h) located with the Biomass...

  11. Fusion characterization of biomass ash

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Teng [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Sino-Danish Center for Education and Research, Beijing, 100190 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Fan, Chuigang; Hao, Lifang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Li, Songgeng, E-mail: sgli@ipe.ac.cn [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Song, Wenli [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Lin, Weigang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Department of Chemical and Biochemical Engineering, Technical University of Denmark, 2800 Kgs. Lyngby (Denmark)

    2016-08-20

    Highlights: • A novel method is proposed to analyze fusion characteristics of biomass ash. • T{sub m} can represent the severe melting temperature of biomass ash. • Compared with AFT, TMA is the better choice to analyze the fusion characteristics of biomass ash. - Abstract: The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, T{sub m}, is proposed to represent the severe melting temperature of biomass ash. The fusion characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates.

  12. Biomass pretreatment: fundamentals toward application.

    Science.gov (United States)

    Agbor, Valery B; Cicek, Nazim; Sparling, Richard; Berlin, Alex; Levin, David B

    2011-01-01

    Development of sustainable energy systems based on renewable biomass feedstocks is now a global effort. Lignocellulosic biomass contains polymers of cellulose, hemicellulose, and lignin, bound together in a complex structure. Liquid biofuels, such as ethanol, can be made from biomass via fermentation of sugars derived from the cellulose and hemicellulose within lignocellulosic materials, but the biomass must be subjected to pretreatment processes to liberate the sugars needed for fermentation. Production of value-added co-products along-side biofuels through integrated biorefinery processes creates the need for selectivity during pretreatment. This paper presents a survey of biomass pretreatment technologies with emphasis on concepts, mechanism of action and practicability. The advantages and disadvantages, and the potential for industrial applications of different pretreatment technologies are the highlights of this paper. Copyright © 2011 Elsevier Inc. All rights reserved.

  13. Fusion characterization of biomass ash

    DEFF Research Database (Denmark)

    Ma, Teng; Fan, Chuigang; Hao, Lifang

    2016-01-01

    The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two...... stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, Tm, is proposed to represent the severe melting temperature of biomass ash. The fusion...... characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates....

  14. Conditioning biomass for microbial growth

    Science.gov (United States)

    Bodie, Elizabeth A; England, George

    2015-03-31

    The present invention relates to methods for improving the yield of microbial processes that use lignocellulose biomass as a nutrient source. The methods comprise conditioning a composition comprising lignocellulose biomass with an enzyme composition that comprises a phenol oxidizing enzyme. The conditioned composition can support a higher rate of growth of microorganisms in a process. In one embodiment, a laccase composition is used to condition lignocellulose biomass derived from non-woody plants, such as corn and sugar cane. The invention also encompasses methods for culturing microorganisms that are sensitive to inhibitory compounds in lignocellulose biomass. The invention further provides methods of making a product by culturing the production microorganisms in conditioned lignocellulose biomass.

  15. Conditioning biomass for microbial growth

    Energy Technology Data Exchange (ETDEWEB)

    Bodie, Elizabeth A; England, George

    2015-03-31

    The present invention relates to methods for improving the yield of microbial processes that use lignocellulose biomass as a nutrient source. The methods comprise conditioning a composition comprising lignocellulose biomass with an enzyme composition that comprises a phenol oxidizing enzyme. The conditioned composition can support a higher rate of growth of microorganisms in a process. In one embodiment, a laccase composition is used to condition lignocellulose biomass derived from non-woody plants, such as corn and sugar cane. The invention also encompasses methods for culturing microorganisms that are sensitive to inhibitory compounds in lignocellulose biomass. The invention further provides methods of making a product by culturing the production microorganisms in conditioned lignocellulose biomass.

  16. Energy from biomass. Teaching material; Energie aus Biomasse. Ein Lehrmaterial

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-04-01

    The textbook discusses the available options for power and heat generation from biomass as well as the limits of biomass-based power supply. The main obstacle apart from the high cost is a lack of knowledge, which the book intends to remedy. It addresses students of agriculture, forestry, environmental engineering, heating systems engineering and apprentice chimney sweepers, but it will also be useful to all other interested readers. [German] Biomasse kann aufgrund seiner vielfaeltigen Erscheinungs- und Umwandlungsformen sowohl als Brennstoff zur Waerme- und Stromgewinnung oder als Treibstoff eingesetzt werden. Die energetische Nutzung von Biomasse birgt zudem nicht zu verachtende Vorteile. Zum einen wegen des Beitrags zum Klimaschutz aufgrund der CO{sub 2}-Neutralitaet oder einfach, weil Biomasse immer wieder nachwaechst und von fossilen Ressourcen unabhaengig macht. All den bisher erschlossenen Moeglichkeiten der energetischen Nutzung von Biomasse moechte dieses Lehrbuch Rechnung tragen. Es zeigt aber auch die Grenzen auf, die mit der Energieversorgung durch Bioenergie einhergehen. Hohe Kosten und ein erhebliches Informationsdefizit behinderten bisher eine verstaerkte Nutzung dieses Energietraeges. Letzterem soll dieses Lehrbuch entgegenwirken. Das vorliegende Lehrbuch wurde fuer die Aus- und Weiterbildung erstellt. Es richtet sich vor allem an angehende Land- und Forstwirte, Umwelttechniker, Heizungsbauer und Schornsteinfeger, ist aber auch fuer all diejenigen interessant, die das Thema ''Energie aus Biomasse'' verstehen und ueberblicken moechten. (orig.)

  17. Treatment of biomass to obtain fermentable sugars

    Science.gov (United States)

    Dunson, Jr., James B.; Tucker, Melvin; Elander, Richard; Hennessey, Susan M.

    2011-04-26

    Biomass is pretreated using a low concentration of aqueous ammonia at high biomass concentration. Pretreated biomass is further hydrolyzed with a saccharification enzyme consortium. Fermentable sugars released by saccharification may be utilized for the production of target chemicals by fermentation.

  18. Pilot experiment on utilization of vegetable biomass in Umbria. Part 2. Anaerobic digestion of the wastes coming from the maintenance activity of the lake Trasimeno and the working of energetic cultures; Sperimentazioni pilota sulla utilizzazione delle biomasse vegetali reperibili nella Regione Umbria. Parte 2. Digestione anaerobica dei residui derivanti dall'attivita' manutentiva del lago Trasimeno e dalla lavorazione di culture agro-energetiche

    Energy Technology Data Exchange (ETDEWEB)

    Poletti, A.; Selvaggi, R.; Poletti, L. [Perugia Univ., Perugia (Italy). Dipt. di Chimica, Laboratorio di Chimica Fisica e Modellistica Ambientale

    2000-12-01

    In this work the energetic exploitation has been assessed of the vegetable biomasses available in the region Umbria, derived both from the maintenance operation of Lake Trasimeno and energetic cultures. Biomethanation experiments have been carried out both on laboratory scale, by preparing anaerobic digestion tests in batch and in continuous, and on pilot scale, through the use of a 2000 litres digestor. Throughout the experiment the main chemical and physical process parameters have been monitored and the process efficiency assessed. The experimental values, measured for the anaerobic digestion process, have shown that both types of biomass can be very good substrated for the production of biogas. Their energetic re-use, when considering the broad and complex problems posed by breeding wastes disposal, could positively contribute to a rational sustainability scheme of the activities operating in the territory. [Italian] In questo lavoro viene valutata la valorizzazione energetica di biomasse vegetali disponibili nella regione Umbria, derivanti dalle operazioni di manutenzione dal Lago Trasimeno e da culture energetiche. Gli esperimenti di digestione anaerobica sono stati eseguiti su scala di laboratorio, con prove in batch ed in continuo, e su scala pilota utilizzando un digestore della capacita' di 2000 libri. Durante il corso degli esperimenti sono stati monitorati i principali parametri chimici e fisici del processo e verificati i rendimenti. I valori sperimentali, misurati per il processo di digestione anaerobica, hanno dimostrato che i due tipi di biomassa studiati possono rappresentare un ottimo substrato per la produzione di biogas. Il loro recupero a fini energetici, inserito nella piu' ampia e complessa problematica connessa con lo smaltimento dei reflui zootecnici, potrebbe contribuire ad un inquadramento razionale della sostenibilita' delle attivita' presenti in quel territorio.

  19. EnerGEO biomass pilot

    Energy Technology Data Exchange (ETDEWEB)

    Tum, M.; Guenther, K.P. [German Aerospace Center (DLR), Wessling (Germany). German Remote Sensing Data Center (DFD); McCallum, I.; Balkovic, J.; Khabarov, N.; Kindermann, G.; Leduc, S. [International Institute for Applied Systems Analysis (IIASA), Laxenburg (Austria); Biberacher, M. [Research Studios Austria AG (RSA), Salzburg (Austria)

    2013-07-01

    In the framework of the EU FP7 project EnerGEO (Earth Observations for Monitoring and Assessment of the Environmental Impact of Energy Use) sustainable energy potentials for forest and agricultural areas were estimated by applying three different model approaches. Firstly, the Biosphere Energy Transfer Hydrology (BETHY/DLR) model was applied to assess agricultural and forest biomass increases on a regional scale with the extension to grassland. Secondly, the EPIC (Environmental Policy Integrated Climate) - a cropping systems simulation model - was used to estimate grain yields on a global scale and thirdly the Global Forest Model (G4M) was used to estimate global woody biomass harvests and stock. The general objective of the biomass pilot is to implement the observational capacity for using biomass as an important current and future energy resource. The scope of this work was to generate biomass energy potentials for locations on the globe and to validate these data. Therefore, the biomass pilot was focused to use historical and actual remote sensing data as input data for the models. For validation purposes, forest biomass maps for 1987 and 2002 for Germany (Bundeswaldinventur (BWI-2)) and 2001 and 2008 for Austria (Austrian Forest Inventory (AFI)) were prepared as reference. (orig.)

  20. Plasma Treatments and Biomass Gasification

    Science.gov (United States)

    Luche, J.; Falcoz, Q.; Bastien, T.; Leninger, J. P.; Arabi, K.; Aubry, O.; Khacef, A.; Cormier, J. M.; Lédé, J.

    2012-02-01

    Exploitation of forest resources for energy production includes various methods of biomass processing. Gasification is one of the ways to recover energy from biomass. Syngas produced from biomass can be used to power internal combustion engines or, after purification, to supply fuel cells. Recent studies have shown the potential to improve conventional biomass processing by coupling a plasma reactor to a pyrolysis cyclone reactor. The role of the plasma is twofold: it acts as a purification stage by reducing production of tars and aerosols, and simultaneously produces a rich hydrogen syngas. In a first part of the paper we present results obtained from plasma treatment of pyrolysis oils. The outlet gas composition is given for various types of oils obtained at different experimental conditions with a pyrolysis reactor. Given the complexity of the mixtures from processing of biomass, we present a study with methanol considered as a model molecule. This experimental method allows a first modeling approach based on a combustion kinetic model suitable to validate the coupling of plasma with conventional biomass process. The second part of the paper is summarizing results obtained through a plasma-pyrolysis reactor arrangement. The goal is to show the feasibility of this plasma-pyrolysis coupling and emphasize more fundamental studies to understand the role of the plasma in the biomass treatment processes.

  1. Thermochemical behavior of pretreated biomass

    Energy Technology Data Exchange (ETDEWEB)

    Biswas, Amit Kumar

    2011-07-01

    Mankind has to provide a sustainable alternative to its energy related problems. Bioenergy is considered as one of the potential renewable energy resources and as a result bioenergy market is also expected to grow dramatically in future. However, logistic issues are of serious concern while considering biomass as an alternative to fossil fuel. It can be improved by introducing pretreated wood pellet. The main objective of this thesis is to address thermochemical behaviour of steam exploded pretreated biomass. Additionally, process aspects of torrefaction were also considered in this thesis. Steam explosion (SE) was performed in a laboratory scale reactor using Salix wood chips. Afterwards, fuel and thermochemical aspects of SE residue were investigated. It was found that Steam explosion pretreatment improved both fuel and pellet quality. Pyrolysis of SE residue reveals that alerted biomass composition significantly affects its pyrolysis behaviour. Contribution from depolymerized components (hemicellulose, cellulose and lignin) of biomass was observed explicitly during pyrolysis. When devolatilization experiment was performed on pellet produced from SE residue, effect of those altered components was observed. In summary, pretreated biomass fuel characteristics is significantly different in comparison with untreated biomass. On the other hand, Process efficiency of torrefaction was found to be governed by the choice of appropriate operating conditions and the type of biomass.

  2. Bearings for the biomass boom

    Energy Technology Data Exchange (ETDEWEB)

    MacQueen, Duncan

    2011-03-15

    Biomass energy is booming –– more than two billion people depend on biomass for their energy and the International Energy Agency predicts that biomass' share of the global energy supply will treble by 2050. But in many developing countries it is still regarded as a traditional and dirty solution that is often criminalised, unsustainable and poorly paid. A more sophisticated approach that legalises and secures sustainable production by and for local people could help improve energy security, cut carbon emissions, protect forests and reduce poverty.

  3. Biomass energy and marginal areas

    Energy Technology Data Exchange (ETDEWEB)

    Chassany, J.P.

    1984-01-01

    The aim of this study was to analyze the conditions and effects of a possible development of the biomass energy upgrading in uneconomical or not rentable areas. The physical, social and economical characteristics of these regions (in France) are described; then the different types of biomass are presented (agricultural wastes, energetic cultures, forest and land products and residues, food processing effluents, municipal wastes) as well as the various energy process (production of alcohol, methane, thermochemical processes, vegetable oils). The development and the feasability of these processes in marginal areas are finally analyzed taking into account the accessibility of the biomass and the technical and commercial impacts.

  4. Ash Properties of Alternative Biomass

    DEFF Research Database (Denmark)

    Capablo, Joaquin; Jensen, Peter Arendt; Pedersen, Kim Hougaard

    2009-01-01

    The ash behavior during suspension firing of 12 alternative solid biofuels, such as pectin waste, mash from a beer brewery, or waste from cigarette production have been studied and compared to wood and straw ash behavior. Laboratory suspension firing tests were performed on an entrained flow...... analysis into three main groups depending upon their ash content of silica, alkali metal, and calcium and magnesium. To further detail the biomass classification, the relative molar ratio of Cl, S, and P to alkali were included. The study has led to knowledge on biomass fuel ash composition influence...... on ash transformation, ash deposit flux, and deposit chlorine content when biomass fuels are applied for suspension combustion....

  5. Biomass combustion gas turbine CHP

    Energy Technology Data Exchange (ETDEWEB)

    Pritchard, D.

    2002-07-01

    This report summarises the results of a project to develop a small scale biomass combustor generating system using a biomass combustor and a micro-gas turbine indirectly fired via a high temperature heat exchanger. Details are given of the specification of commercially available micro-turbines, the manufacture of a biomass converter, the development of a mathematical model to predict the compatibility of the combustor and the heat exchanger with various compressors and turbines, and the utilisation of waste heat for the turbine exhaust.

  6. Catalytic gasification of biomass

    Science.gov (United States)

    Robertus, R. J.; Mudge, L. K.; Sealock, L. J., Jr.; Mitchell, D. H.; Weber, S. L.

    1981-12-01

    Methane and methanol synthesis gas can be produced by steam gasification of biomass in the presence of appropriate catalysts. This concept is to use catalysts in a fluidized bed reactor which is heated indirectly. The objective is to determine the technical and economic feasibility of the concept. Technically the concept has been demonstrated on a 50 lb per hr scale. Potential advantages over conventional processes include: no oxygen plant is needed, little tar is produced so gas and water treatment are simplified, and yields and efficiencies are greater than obtained by conventional gasification. Economic studies for a plant processing 2000 T/per day dry wood show that the cost of methanol from wood by catalytic gasification is competitive with the current price of methanol. Similar studies show the cost of methane from wood is competitive with projected future costs of synthetic natural gas. When the plant capacity is decreased to 200 T per day dry wood, neither product is very attractive in today's market.

  7. Biomass catalysis and solvents; Biomasse catalyse et solvants

    Energy Technology Data Exchange (ETDEWEB)

    Pioch, D. [CIRAD-AMIS, programme Agro-Alimentaire, 34 - Montpellier (France); Pouilloux, Y.; Barrault, J. [Centre National de la Recherche Scientifique (CNRS UMR 6503), ESIP, Lab. de Catalyse en Chimie Organique, 86 - Poitiers (France)] [and others

    2000-07-01

    How to develop new technics and products and at the same time to respect the environment? The biomass seems to be an interesting domain in this framework and this document allows the selection of performing products obtain by biomass. Among these products the solvents economic and environmental advantages or consequences are discussed. A great part is also devoted to the voc emissions, bound to the solvents.

  8. Washington State biomass data book

    Energy Technology Data Exchange (ETDEWEB)

    Deshaye, J.A.; Kerstetter, J.D.

    1991-07-01

    This is the first edition of the Washington State Biomass Databook. It assess sources and approximate costs of biomass fuels, presents a view of current users, identifies potential users in the public and private sectors, and lists prices of competing energy resources. The summary describes key from data from the categories listed above. Part 1, Biomass Supply, presents data increasing levels of detail on agricultural residues, biogas, municipal solid waste, and wood waste. Part 2, Current Industrial and Commercial Use, demonstrates how biomass is successfully being used in existing facilities as an alternative fuel source. Part 3, Potential Demand, describes potential energy-intensive public and private sector facilities. Part 4, Prices of Competing Energy Resources, shows current suppliers of electricity and natural gas and compares utility company rates. 49 refs., 43 figs., 72 tabs.

  9. ROE Carbon Storage - Forest Biomass

    Data.gov (United States)

    U.S. Environmental Protection Agency — This polygon dataset depicts the density of forest biomass in counties across the United States, in terms of metric tons of carbon per square mile of land area....

  10. Plant biomass degradation by fungi.

    Science.gov (United States)

    Mäkelä, Miia R; Donofrio, Nicole; de Vries, Ronald P

    2014-11-01

    Plant biomass degradation by fungi has implications for several fields of science. The enzyme systems employed by fungi for this are broadly used in various industrial sectors such as food & feed, pulp & paper, detergents, textile, wine, and more recently biofuels and biochemicals. In addition, the topic is highly relevant in the field of plant pathogenic fungi as they degrade plant biomass to either gain access to the plant or as carbon source, resulting in significant crop losses. Finally, fungi are the main degraders of plant biomass in nature and as such have an essential role in the global carbon cycle and ecology in general. In this review we provide a global view on the development of this research topic in saprobic ascomycetes and basidiomycetes and in plant pathogenic fungi and link this to the other papers of this special issue on plant biomass degradation by fungi. Copyright © 2014 Elsevier Inc. All rights reserved.

  11. Biomass processing over gold catalysts

    CERN Document Server

    Simakova, Olga A; Murzin, Dmitry Yu

    2014-01-01

    The book describes the valorization of biomass-derived compounds over gold catalysts. Since biomass is a rich renewable feedstock for diverse platform molecules, including those currently derived from petroleum, the interest in various transformation routes has become intense. Catalytic conversion of biomass is one of the main approaches to improving the economic viability of biorefineries.  In addition, Gold catalysts were found to have outstanding activity and selectivity in many key reactions. This book collects information about transformations of the most promising and important compounds derived from cellulose, hemicelluloses, and woody biomass extractives. Since gold catalysts possess high stability under oxidative conditions, selective oxidation reactions were discussed more thoroughly than other critical reactions such as partial hydrogenation, acetalization, and isomerization. The influence of reaction conditions, the role of the catalyst, and the advantages and disadvantages of using gold are pre...

  12. On biomass of parasitic plants

    Energy Technology Data Exchange (ETDEWEB)

    He, J H [Modern Textile Institute, Donghua University, 1882 Yan' an Xilu Road, Shanghai 200051 (China); Mo, L-F [School of Information Engineering, Zhejiang Forestry College, Lin' an 311300, Zhejiang (China)], E-mail: jhhe@dhu.edu.cn

    2008-02-15

    An extremely simple and elementary but rigorous derivation of maximal biomass of parasitic plants is given using an assumption that metabolic rate of the parasite should not be larger than that of its host organ.

  13. On biomass of parasitic plants

    Science.gov (United States)

    He, J. H.; Mo, L.-F.

    2008-02-01

    An extremely simple and elementary but rigorous derivation of maximal biomass of parasitic plants is given using an assumption that metabolic rate of the parasite should not be larger than that of its host organ

  14. Liquid biofuels from blue biomass

    DEFF Research Database (Denmark)

    Kádár, Zsófia; Jensen, Annette Eva; Bangsø Nielsen, Henrik

    2011-01-01

    Marine (blue) biomasses, such as macroalgaes, represent a huge unexploited amount of biomass. With their various chemical compositions, macroalgaes can be a potential substrate for food, feed, biomaterials, pharmaceuticals, health care products and also for bioenergy. Algae use seawater as a growth...... be the well suited candidates as feedstock for biofuel production in the future. The aim of our studies is to examine the possibility producing liquid biofuel (ethanol and butanol) from macroalgaes....

  15. Experiences with biomass in Denmark

    DEFF Research Database (Denmark)

    Gregg, Jay Sterling; Bolwig, Simon; Solér, Ola

    The Bioenergy Department in SENER have requested assistance with planning for the deployment of bioenergy (Biomass, biogas and waste incineration) in Mexico and information on Danish experiences with developing policy initiatives promoting bioenergy. This introduction to the Danish experiences...... with biomass use is compiled as preparation for SENER’s potential visit to Denmark in 2014. This report was prepared 19 June, 2014 by DTU System Analysis to Danish Energy Agency (DEA) as part of a frame contract agreement....

  16. Biogas from lignocellulosic biomass

    Energy Technology Data Exchange (ETDEWEB)

    Berglund Odhner, Peter; Schabbauer, Anna [Grontmij AB, Stockholm (Sweden); Sarvari Horvath, Ilona; Mohseni Kabir, Maryam [Hoegskolan i Boraas, Boraas (Sweden)

    2012-01-15

    Grontmij AB has cooperated with the University of Boraas to evaluate the technological and economical possibilities for biogas production from substrates containing lignocellulose, such as forest residues, straw and paper. The state of knowledge regarding biogas production from cellulosic biomass has been summarized. The research in the field has been described, especially focusing on pretreatment methods and their results on increased gas yields. An investigation concerning commercially available pretreatment methods and the cost of these technologies has been performed. An economic evaluation of biogas production from lignocellulosic materials has provided answers to questions regarding the profitability of these processes. Pretreatment with steam explosion was economically evaluated for three feedstocks - wood, straw and paper - and a combination of steam explosion and addition of NaOH for paper. The presented costs pertain to costs for the pretreatment step as it, in this study, was assumed that the pretreatment would be added to an existing plant and the lignocellulosic substrates would be part of a co-digestion process. The results of the investigation indicate that it is difficult to provide a positive net result when comparing the cost of pretreatment versus the gas yield (value) for two of the feedstocks - forest residues and straw. This is mainly due to the high cost of the raw material. For forest residues the steam pretreatment cost exceeded the gas yield by over 50 %, mainly due to the high cost of the raw material. For straw, the production cost was similar to the value of the gas. Paper showed the best economic result. The gas yield (value) for paper exceeded the pretreatment cost by 15 %, which makes it interesting to study paper further.

  17. Biomass for iron ore sintering

    Energy Technology Data Exchange (ETDEWEB)

    Zandi, M.; Martinez-Pacheco, M.; Fray, T.A.T. [Corus Research Development & Technology, Rotherham (United Kingdom)

    2010-11-15

    Within an integrated steelworks, iron ore sinter making is an energy intensive process. In recent years, biomass is becoming an attractive alternative source of energy to traditional fossil fuels such as coal. In this study, commercially available biomass materials suited to sinter making have been identified as an alternative source of fuel to coke breeze. Olive residues, sunflower husk pellets, almond shells, hazelnut shells and Bagasse pellets have been characterised and prepared for sintering. A laboratory sinter pot has been employed for studying sintering behaviour of biomass material. On average, the calorific values of selected biomass materials, on a dry basis, are about 65% of dry coke breeze. It was found that less of this energy would be available in sinter making due to the evaporation of some of the volatile matter ahead of the flame front. At a replacement rate of 25%, the crushed sunflower husk pellets showed the closest thermal profile to that of coke breeze alone in the size range of -0.8 to +0.6 mm. A specification of less than 1 mm has been recommended for the studied biomass materials when co-firing biomass with coke breeze for iron ore sintering.

  18. Potential of cofiring with biomass in Italy

    Energy Technology Data Exchange (ETDEWEB)

    Aresta, M.; Tommasi, I.; Galatola, M. [University of Bari (Italy). Dept. of Chemistry

    1997-12-31

    Biomass is considered a potential fuel and a renewable source for the future. In Italy, the utilization of biomass nowadays is addressed, above all, towards thermal energy production. In the near future, however, it is predictable a higher differentiation in order to use biomass with the more suitable technology. In this paper we review the utilization of residual biomasses. (Author)

  19. Seaweed and Biomass production

    Science.gov (United States)

    Nadiradze, K. T.

    2016-02-01

    The Black Sea has a sensitive ecosystem, vulnerable to the potential impacts by climate, water quality, pollution and etc. Successfully restoring and sustaining healthy Black Sea aqua cultural farming will require concreted action by private sector, civil society, farmer organizations and other stakeholders. But to achieve agri-environmental goals at scale, well-organized policy goals, framework and strategy for Sea Agriculture Green energy, Algae Biomass, Sapropel Production, aquacultures farming are essential for Georgian Farmers. But we must recognizes the most sustainable and at least risky farming systems will be those that build in aqua cultural, environmental, and social management practices resilient to climate ch ange and other risks and shocks evident in Georgia and whole in a Black Sea Basin Countries. Black Sea has more than 600 kinds of seaweeds; these species contain biologically active substances also present in fish - vitamins and omega fatty acids. The task is to specify how Black Sea seaweeds can be used in preparing nutrition additives, medicines and cosmetic products. As elsewhere around the world, governments, civil society, and the private sector in Georgia should work together to develop and implement `Blue Economy' and Green Growth strategies to generate equitable, sustainable economic development through strengthening Sea Agriculture. We are very interested to develop Black Sea seaweed plantation ad farming for multiply purposes fo r livestock as food additives, for human as great natural source of iodine as much iodine are released by seaweeds into the atmosphere to facilitate the development of better models or aerosol formation and atmospheric chemistry. It is well known, that earth's oceans are thought to have absorbed about one quarter of the CO2 humans pumped into the atmosphere over the past 20 years. The flip side of this process is that, as they absorb co2, oceans also become more acidic with dramatic consequences for sea life

  20. Fiscalini Farms Biomass Energy Project

    Energy Technology Data Exchange (ETDEWEB)

    William Stringfellow; Mary Kay Camarillo; Jeremy Hanlon; Michael Jue; Chelsea Spier

    2011-09-30

    In this final report describes and documents research that was conducted by the Ecological Engineering Research Program (EERP) at the University of the Pacific (Stockton, CA) under subcontract to Fiscalini Farms LP for work under the Assistance Agreement DE-EE0001895 'Measurement and Evaluation of a Dairy Anaerobic Digestion/Power Generation System' from the United States Department of Energy, National Energy Technology Laboratory. Fiscalini Farms is operating a 710 kW biomass-energy power plant that uses bio-methane, generated from plant biomass, cheese whey, and cattle manure via mesophilic anaerobic digestion, to produce electricity using an internal combustion engine. The primary objectives of the project were to document baseline conditions for the anaerobic digester and the combined heat and power (CHP) system used for the dairy-based biomass-energy production. The baseline condition of the plant was evaluated in the context of regulatory and economic constraints. In this final report, the operation of the plant between start-up in 2009 and operation in 2010 are documented and an interpretation of the technical data is provided. An economic analysis of the biomass energy system was previously completed (Appendix A) and the results from that study are discussed briefly in this report. Results from the start-up and first year of operation indicate that mesophilic anaerobic digestion of agricultural biomass, combined with an internal combustion engine, is a reliable source of alternative electrical production. A major advantage of biomass energy facilities located on dairy farms appears to be their inherent stability and ability to produce a consistent, 24 hour supply of electricity. However, technical analysis indicated that the Fiscalini Farms system was operating below capacity and that economic sustainability would be improved by increasing loading of feedstocks to the digester. Additional operational modifications, such as increased utilization of

  1. Pyrolytic sugars from cellulosic biomass

    Science.gov (United States)

    Kuzhiyil, Najeeb

    Sugars are the feedstocks for many promising advanced cellulosic biofuels. Traditional sugars derived from starch and sugar crops are limited in their availability. In principle, more plentiful supply of sugars can be obtained from depolymerization of cellulose, the most abundant form of biomass in the world. Breaking the glycosidic bonds between the pyranose rings in the cellulose chain to liberate glucose has usually been pursued by enzymatic hydrolysis although a purely thermal depolymerization route to sugars is also possible. Fast pyrolysis of pure cellulose yields primarily levoglucosan, an anhydrosugar that can be hydrolyzed to glucose. However, naturally occurring alkali and alkaline earth metals (AAEM) in biomass are strongly catalytic toward ring-breaking reactions that favor formation of light oxygenates over anhydrosugars. Removing the AAEM by washing was shown to be effective in increasing the yield of anhydrosugars; but this process involves removal of large amount of water from biomass that renders it energy intensive and thereby impractical. In this work passivation of the AAEM (making them less active or inactive) using mineral acid infusion was explored that will increase the yield of anhydrosugars from fast pyrolysis of biomass. Mineral acid infusion was tried by previous researchers, but the possibility of chemical reactions between infused acid and AAEM in the biomass appears to have been overlooked, possibly because metal cations might be expected to already be substantially complexed to chlorine or other strong anions that are found in biomass. Likewise, it appears that previous researchers assumed that as long as AAEM cations were in the biomass, they would be catalytically active regardless of the nature of their complexion with anions. On the contrary, we hypothesized that AAEM can be converted to inactive or less active salts using mineral acids. Various biomass feedstocks were infused with mineral (hydrochloric, nitric, sulfuric and

  2. COFIRING BIOMASS WITH LIGNITE COAL

    Energy Technology Data Exchange (ETDEWEB)

    Darren D. Schmidt

    2002-01-01

    The University of North Dakota Energy & Environmental Research Center, in support of the U.S. Department of Energy's (DOE) biomass cofiring program, completed a Phase 1 feasibility study investigating aspects of cofiring lignite coal with biomass relative to utility-scale systems, specifically focusing on a small stoker system located at the North Dakota State Penitentiary (NDSP) in Bismarck, North Dakota. A complete biomass resource assessment was completed, the stoker was redesigned to accept biomass, fuel characterization and fireside modeling tests were performed, and an engineering economic analysis was completed. In general, municipal wood residue was found to be the most viable fuel choice, and the modeling showed that fireside problems would be minimal. Experimental ash deposits from firing 50% biomass were found to be weaker and more friable compared to baseline lignite coal. Experimental sulfur and NO{sub x} emissions were reduced by up to 46%. The direct costs savings to NDSP, from cogeneration and fuel saving, results in a 15- to 20-year payback on a $1,680,000 investment, while the total benefits to the greater community would include reduced landfill burden, alleviation of fees for disposal by local businesses, and additional jobs created both for the stoker system as well as from the savings spread throughout the community.

  3. Biomass of cocoa and sugarcane

    Science.gov (United States)

    Siswanto; Sumanto; Hartati, R. S.; Prastowo, B.

    2017-05-01

    The role of the agricultural sector is very important as the upstream addressing downstream sectors and national energy needs. The agricultural sector itself is also highly dependent on the availability of energy. Evolving from it then it must be policies and strategies for agricultural development Indonesia to forward particularly agriculture as producers as well as users of biomass energy or bioenergy for national development including agriculture balance with agriculture and food production. Exports of biomass unbridled currently include preceded by ignorance, indifference and the lack of scientific data and potential tree industry in the country. This requires adequate scientific supporting data. This study is necessary because currently there are insufficient data on the potential of biomass, including tree biomasanya detailing the benefits of bioenergy, feed and food is very necessary as a basis for future policy. Measurement of the main estate plants biomass such as cocoa and sugarcane be done in 2015. Measurements were also conducted on its lignocellulose content. Tree biomass sugarcane potential measured consist of leaves, stems and roots, with the weight mostly located on the stem. Nevertheless, not all the potential of the stem is a good raw material for bioethanol. For cocoa turned out leaves more prospective because of its adequate hemicellulose content. For sugarcane, leaf buds contain a good indicator of digestion of feed making it more suitable for feed.

  4. Biomass living energy; Biomasse l'energie vivante

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    Any energy source originating from organic matter is biomass, which even today is the basic source of energy for more than a quarter of humanity. Best known for its combustible properties, biomass is also used to produce biofuels. This information sheet provides also information on the electricity storage from micro-condensers to hydroelectric dams, how to save energy facing the increasing of oil prices and supply uncertainties, the renewable energies initiatives of Cork (Ireland) and the Switzerland european energy hub. (A.L.B.)

  5. Wind, biomass, hydrogen: renewable energies; Vent, biomasse, hydrogene: energies renouvelables

    Energy Technology Data Exchange (ETDEWEB)

    Rakotosson, V.; Brousse, Th.; Guillemet, Ph.; Scudeller, Y.; Crosnier, O.; Dugas, R.; Favier, F.; Zhou, Y.; Taberna, P.M.; Simon, P.; Toupin, M.; Belanger, D.; Ngo, Ch.; Djamie, B.; Guyard, Ch.; Tamain, B.; Ruer, J.; Ungerer, Ph.; Bonal, J.; Flamant, G

    2007-06-15

    This press kit gathers a series of articles about renewable energies: the compared availabilities of renewable energy sources (comparison at a given time); offshore wind turbines (projects under development, cost optimisation); hydrogen for transports: present day situation (production, transport and storage, hydrogen conversion into mechanical energy, indirect use in biomass conversion); biomass: future carbon source (resource potential in France, pyrolysis and fermentation, development of biofuels and synthetic fuels, stakes for agriculture); beneficial standards for the heat pumps market (market organization and quality approach); collecting solar energy (solar furnaces and future solar power plants, hydrogen generation). (J.S.)

  6. Forestry and biomass energy projects

    DEFF Research Database (Denmark)

    Swisher, J.N.

    1994-01-01

    This paper presents a comprehensive and consistent methodology to account for the costs and net carbon flows of different categories of forestry and biomass energy projects and describes the application of the methodology to several sets of projects in Latin America. The results suggest that both...... is sufficient as either a national or global strategy for sustainable land use or carbon emission reduction. The methodology allows consistent comparisons of the costs and quantities of carbon stored in different types of projects and/or national programs, facilitating the inclusion of forestry and biomass...... biomass energy development and forestry measures including reforestation and forest protection can contribute significantly to the reduction of global CO2 emissions, and that local land-use capacity must determine the type of project that is appropriate in specific cases. No single approach alone...

  7. Biomass furnace: projection and construction

    Energy Technology Data Exchange (ETDEWEB)

    Melo, Fernanda Augusta de Oliveira; Silva, Juarez Sousa e; Silva, Denise de Freitas; Sampaio, Cristiane Pires; Nascimento Junior, Jose Henrique do [Universidade Federal de Vicosa (DEA/UFV), MG (Brazil). Dept. de Engenharia Agricola

    2008-07-01

    Of all the ways to convert biomass into thermal energy, direct combustion is the oldest. The thermal-chemical technologies of biomass conversion such as pyrolysis and gasification, are currently not the most important alternatives; combustion is responsible for 97% of the bio-energy produced in the world (Demirbas, 2003). For this work, a small furnace was designed and constructed to use biomass as its main source of fuel, and the combustion chamber was coupled with a helical transporter which linked to the secondary fuel reservoir to continually feed the combustion chamber with fine particles of agro-industrial residues. The design of the stove proved to be technically viable beginning with the balance of mass and energy for the air heating system. The proposed heat generator was easily constructed as it made use of simple and easily acquired materials, demanding no specialized labor. (author)

  8. A sustainable woody biomass biorefinery.

    Science.gov (United States)

    Liu, Shijie; Lu, Houfang; Hu, Ruofei; Shupe, Alan; Lin, Lu; Liang, Bin

    2012-01-01

    Woody biomass is renewable only if sustainable production is imposed. An optimum and sustainable biomass stand production rate is found to be one with the incremental growth rate at harvest equal to the average overall growth rate. Utilization of woody biomass leads to a sustainable economy. Woody biomass is comprised of at least four components: extractives, hemicellulose, lignin and cellulose. While extractives and hemicellulose are least resistant to chemical and thermal degradation, cellulose is most resistant to chemical, thermal, and biological attack. The difference or heterogeneity in reactivity leads to the recalcitrance of woody biomass at conversion. A selection of processes is presented together as a biorefinery based on incremental sequential deconstruction, fractionation/conversion of woody biomass to achieve efficient separation of major components. A preference is given to a biorefinery absent of pretreatment and detoxification process that produce waste byproducts. While numerous biorefinery approaches are known, a focused review on the integrated studies of water-based biorefinery processes is presented. Hot-water extraction is the first process step to extract value from woody biomass while improving the quality of the remaining solid material. This first step removes extractives and hemicellulose fractions from woody biomass. While extractives and hemicellulose are largely removed in the extraction liquor, cellulose and lignin largely remain in the residual woody structure. Xylo-oligomers, aromatics and acetic acid in the hardwood extract are the major components having the greatest potential value for development. Higher temperature and longer residence time lead to higher mass removal. While high temperature (>200°C) can lead to nearly total dissolution, the amount of sugars present in the extraction liquor decreases rapidly with temperature. Dilute acid hydrolysis of concentrated wood extracts renders the wood extract with monomeric sugars

  9. Leaching From Biomass Gasification Residues

    DEFF Research Database (Denmark)

    Allegrini, Elisa; Boldrin, Alessio; Polletini, A.

    2011-01-01

    The aim of the present work is to attain an overall characterization of solid residues from biomass gasification. Besides the determination of chemical and physical properties, the work was focused on the study of leaching behaviour. Compliance and pH-dependence leaching tests coupled with geoche......The aim of the present work is to attain an overall characterization of solid residues from biomass gasification. Besides the determination of chemical and physical properties, the work was focused on the study of leaching behaviour. Compliance and pH-dependence leaching tests coupled...

  10. Cogasification of Coal and Biomass: A Review

    Directory of Open Access Journals (Sweden)

    J. S. Brar

    2012-01-01

    Full Text Available Recently, there has been significant research interest in cogasification of coal and various types of biomass blends to improve biomass gasification by reducing the tar content in the product gas. In addition, ash present in biomass catalyzes the gasification of coal. However, due to the fibrous nature of biomass and the large difference in gasification temperature of coal and biomass, cogasification in existing systems presents technical challenges. This paper documents research studies conducted on the cogasification of various types of coal and biomass using different types of gasifiers under various sets of operating conditions. In addition, the influence of cogasification on upstream and downstream processing is presented.

  11. Enzyme nanoassemblies for biomass conversion

    Science.gov (United States)

    Biomass represents a vast resource for the production of the world’s fuel and chemical feedstock needs. The use of enzymes to effect these bioconversions offers an alternative that is potentially more specific and environmentally-friendly than harsher chemical methodologies. Some species of anaero...

  12. Biomass energy systems program summary

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-07-01

    Research programs in biomass which were funded by the US DOE during fiscal year 1978 are listed in this program summary. The conversion technologies and their applications have been grouped into program elements according to the time frame in which they are expected to enter the commercial market. (DMC)

  13. Energy from biomass and waste

    NARCIS (Netherlands)

    Faaij, A.P.C.

    2001-01-01

    Biomass, a broad term for all organic matter of plants, trees and crops, is currently regarded as a renewable energy source which can contribute substantially to the world's energy supply in the future. Various scenarios for the development of energy supply and demand, such as compiled by the World

  14. Sustainable Biomass Supply in EU

    Energy Technology Data Exchange (ETDEWEB)

    Elbersen, B. [Alterra, Wageningen University and Research WUR, Wageningen (Netherlands); Van Stralen, J.; Uslu, A. [Unit Policy Studies, Energy research Centre of the Netherlands ECN, Amsterdam (Netherlands); Boettcher, H. [International Institute for Applied Systems Analysis IIASA, Laxenburg (Austria); Panoutsou, C. [Centre for Environmental Policy, Imperial College London, London (United Kingdom); Fritsche, U. [Energy and Climate Division, Oeko-Institut, Darmstadt (Germany)

    2012-04-15

    According to the analysis of the Member States' National Renewable Energy Action Plans, biomass will make up 19% of total renewable electricity in the year 2020, 78% of total renewable heating and cooling in 2020 and 89% of total renewable energy in transport.

  15. Plant biomass degradation by fungi

    NARCIS (Netherlands)

    Mäkelä, Miia R; Donofrio, Nicole; de Vries, Ronald P; van den Brink, J.

    2014-01-01

    Plant biomass degradation by fungi has implications for several fields of science. The enzyme systems employed by fungi for this are broadly used in various industrial sectors such as food & feed, pulp & paper, detergents, textile, wine, and more recently biofuels and biochemicals. In addition, the

  16. Biomass Supply Logistics and Infrastructure

    Science.gov (United States)

    Sokhansanj, Shahabaddine; Hess, J. Richard

    Feedstock supply system encompasses numerous unit operations necessary to move lignocellulosic feedstock from the place where it is produced (in the field or on the stump) to the start of the conversion process (reactor throat) of the biorefinery. These unit operations, which include collection, storage, preprocessing, handling, and transportation, represent one of the largest technical and logistics challenges to the emerging lignocellulosic biorefining industry. This chapter briefly reviews the methods of estimating the quantities of biomass, followed by harvesting and collection processes based on current practices on handling wet and dry forage materials. Storage and queuing are used to deal with seasonal harvest times, variable yields, and delivery schedules. Preprocessing can be as simple as grinding and formatting the biomass for increased bulk density or improved conversion efficiency, or it can be as complex as improving feedstock quality through fractionation, tissue separation, drying, blending, and densification. Handling and transportation consists of using a variety of transport equipment (truck, train, ship) for moving the biomass from one point to another. The chapter also provides typical cost figures for harvest and processing of biomass.

  17. Biomass supply logistics and infrastructure.

    Science.gov (United States)

    Sokhansanj, Shahabaddine; Hess, J Richard

    2009-01-01

    Feedstock supply system encompasses numerous unit operations necessary to move lignocellulosic feedstock from the place where it is produced (in the field or on the stump) to the start of the conversion process (reactor throat) of the biorefinery. These unit operations, which include collection, storage, preprocessing, handling, and transportation, represent one of the largest technical and logistics challenges to the emerging lignocellulosic biorefining industry. This chapter briefly reviews the methods of estimating the quantities of biomass, followed by harvesting and collection processes based on current practices on handling wet and dry forage materials. Storage and queuing are used to deal with seasonal harvest times, variable yields, and delivery schedules. Preprocessing can be as simple as grinding and formatting the biomass for increased bulk density or improved conversion efficiency, or it can be as complex as improving feedstock quality through fractionation, tissue separation, drying, blending, and densification. Handling and transportation consists of using a variety of transport equipment (truck, train, ship) for moving the biomass from one point to another. The chapter also provides typical cost figures for harvest and processing of biomass.

  18. Torrefied biomass-polypropylene composites

    Science.gov (United States)

    Torrefied almond shells and wood chips were incorporated into polypropylene as fillers to produce torrefied biomass-polymer composites. Response surface methodology was used to examine the effects of filler concentration, filler size, and lignin factor (relative lignin to cellulose concentration) on...

  19. Biomass Program Recovery Act Factsheet

    Energy Technology Data Exchange (ETDEWEB)

    None

    2010-03-01

    The Biomass Program has awarded about $718 million in American Recovery and Reinvestment Act (Recovery Act) funds. The projects the Program is supporting are intended to: Accelerate advanced biofuels research, development, and demonstration; Speed the deployment and commercialization of advanced biofuels and bioproducts; Further the U.S. bioindustry through market transformation and creating or saving a range of jobs.

  20. Leaching from biomass combustion ash

    DEFF Research Database (Denmark)

    Maresca, Alberto; Astrup, Thomas Fruergaard

    2014-01-01

    The use of biomass combustion ashes for fertilizing and liming purposes has been widely addressed in scientific literature. Nevertheless, the content of potentially toxic compounds raises concerns for a possible contamination of the soil. During this study five ash samples generated at four...

  1. Energy from biomass and waste

    NARCIS (Netherlands)

    Faaij, A.P.C.

    1997-01-01

    Biomass, a broad term for all organic matter of plants, trees and crops, is currently regarded as a renewable energy source which can contribute substantially to the world's energy supply in the future. Various scenarios for the development of energy supply and demand, such as compiled by the

  2. Photoinduced Biohydrogen Production from Biomass

    Directory of Open Access Journals (Sweden)

    Yutaka Amao

    2008-07-01

    Full Text Available Photoinduced biohydrogen production systems, coupling saccharaides biomass such as sucrose, maltose, cellobiose, cellulose, or saccharides mixture hydrolysis by enzymes and glucose dehydrogenase (GDH, and hydrogen production with platinum colloid as a catalyst using the visible light-induced photosensitization of Mg chlorophyll-a (Mg Chl-a from higher green plant or artificial chlorophyll analog, zinc porphyrin, are introduced.

  3. Plant biomass degradation by fungi

    NARCIS (Netherlands)

    Mäkelä, Miia R; Donofrio, Nicole; de Vries, Ronald P; van den Brink, J.

    2014-01-01

    Plant biomass degradation by fungi has implications for several fields of science. The enzyme systems employed by fungi for this are broadly used in various industrial sectors such as food & feed, pulp & paper, detergents, textile, wine, and more recently biofuels and biochemicals. In addition, the

  4. Fiscalini Farms Biomass Energy Project

    Energy Technology Data Exchange (ETDEWEB)

    William Stringfellow; Mary Kay Camarillo; Jeremy Hanlon; Michael Jue; Chelsea Spier

    2011-09-30

    In this final report describes and documents research that was conducted by the Ecological Engineering Research Program (EERP) at the University of the Pacific (Stockton, CA) under subcontract to Fiscalini Farms LP for work under the Assistance Agreement DE-EE0001895 'Measurement and Evaluation of a Dairy Anaerobic Digestion/Power Generation System' from the United States Department of Energy, National Energy Technology Laboratory. Fiscalini Farms is operating a 710 kW biomass-energy power plant that uses bio-methane, generated from plant biomass, cheese whey, and cattle manure via mesophilic anaerobic digestion, to produce electricity using an internal combustion engine. The primary objectives of the project were to document baseline conditions for the anaerobic digester and the combined heat and power (CHP) system used for the dairy-based biomass-energy production. The baseline condition of the plant was evaluated in the context of regulatory and economic constraints. In this final report, the operation of the plant between start-up in 2009 and operation in 2010 are documented and an interpretation of the technical data is provided. An economic analysis of the biomass energy system was previously completed (Appendix A) and the results from that study are discussed briefly in this report. Results from the start-up and first year of operation indicate that mesophilic anaerobic digestion of agricultural biomass, combined with an internal combustion engine, is a reliable source of alternative electrical production. A major advantage of biomass energy facilities located on dairy farms appears to be their inherent stability and ability to produce a consistent, 24 hour supply of electricity. However, technical analysis indicated that the Fiscalini Farms system was operating below capacity and that economic sustainability would be improved by increasing loading of feedstocks to the digester. Additional operational modifications, such as increased utilization of

  5. Torrefaction of biomass. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-05-15

    The objective of this project was to investigate and understand some of the basics of the process of torrefaction and explore the true characteristics of this new type of solid biomass fuel. Tests with torrefaction of different biomass have thus been conducted in both laboratory scale as well as bench scale investigating samples from milligram up to >100 kg. Test in TGA-FTIR and a lab scale pyro-ofen was used to understand the basic chemistry of the influence of torrefaction temperature on the kinetics of the process as well as the condensable gases leaving the process. The results reveal a process that above 250 deg. C is exothermic and that the major condensable gases consist mainly of methanol, acetic acid and water. Significant amounts of methyl-chloride were detected in the condensable gases and do thereby suggest that a certain amount of corrosive Cl could be reduced from the fuel by means of torrefaction. It was also concluded that great care has to be taken during and after production as the torrefied material was seen to self-ignite in an air environment at temperatures above 200 deg. C. The grindability of the material (energy consumption during milling) is indeed significantly improved by torrefaction and can be reduced up to 6 times compared to raw biomass. The results from test in bench scale as well as in lab scale mills suggested that in order to reach grindability similar to coal a torrefaction temperature above 240 deg. C is required for wood chips and above 290 deg. C for wood pellets. These figures will however differ with the type of biomass torrefied and the particle size of the material torrefied and milled. Moisture uptake in torrefied materials is decreased compared to raw biomass. However, due to formation of cavities in the material during torrefaction, the full effect is met first after densification. The hydrophobicity of the material increases with higher torrefaction temperature, but still a rather significant moisture uptake is

  6. Bioenergy from wastewater-based biomass

    Directory of Open Access Journals (Sweden)

    Ronald C. Sims

    2016-01-01

    Full Text Available The U.S. Department of Energy (DOE has stated that biomass is the only renewable resource that can supplant petroleum-based liquid transportation fuels in the near term. Wastewater is beginning to be viewed as a potential resource that can be exploited for biomass production and conversion to bioenergy. We suggest that using wastewater from municipalities and industries as a resource for cultivating biomass and combining wastewater treatment with the production of biomass for bioenergy would provide benefits to both industries. Two waste-based biomass production systems that currently have large nationwide infrastructures include: (1 wastewater treatment systems that can be used to cultivate algae biomass, and (2 land application/treatment systems for non-food terrestrial biomass. These existing infrastructures could be used in the relatively near future for waste-based biomass production and conversion to bioenergy, thereby reducing capital costs and scalability challenges while making a contribution to energy independence and national security.

  7. New market potential: Torrefaction of Woody Biomass

    Energy Technology Data Exchange (ETDEWEB)

    Jaya Shankar Tumuluru; J. Richard Hess

    2015-07-01

    According to researchers in Idaho National Laboratory’s Bioenergy Program, torrefaction of woody biomass could reduce variability in biomass feedstock and enable development of a commodity-type product for green energy generation and usage.

  8. Treatment of biomass to obtain ethanol

    Science.gov (United States)

    Dunson, Jr., James B.; Elander, Richard T.; Tucker, III, Melvin P.; Hennessey, Susan Marie

    2011-08-16

    Ethanol was produced using biocatalysts that are able to ferment sugars derived from treated biomass. Sugars were obtained by pretreating biomass under conditions of high solids and low ammonia concentration, followed by saccharification.

  9. BSCL Use Plan: Solving Biomass Recalcitrance

    Energy Technology Data Exchange (ETDEWEB)

    Himmel, M.; Vinzant, T.; Bower, S.; Jechura, J.

    2005-08-01

    Technical report describing NREL's new Biomass Surface Characterization Laboratory (BSCL). The BSCL was constructed to provide the most modern commercial surface characterization equipment for studying biomass surfaces.

  10. Development of Solar Biomass Drying System

    OpenAIRE

    Atnaw Samson Mekbib; Bin Che Ku Yahya Che Ku Mohammad Faizal; Jama Oumer Abduaziz

    2017-01-01

    The purpose of this paper focuses on the experimental pre-treatment of biomass in agricultural site using solar energy as power source and contribution of common use and efficiency solar dryer system for consumer. The main purpose of this design for solar cabinet dryer is to dry biomass via direct and indirect heating. Direct heating is the simplest method to dry biomass by exposing the biomass under direct sunlight. The solar cabinet dryer traps solar heat to increase the temperature of the ...

  11. Challenges for sustainable biomass utilisation. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Hiete, Michael; Ludwig, Jens; Bidart, Christian; Schultmann, Frank (eds.)

    2010-07-01

    The energetic use of biomass can provide solutions for the growing worldwide demand for energy and fuel. This book contains the contributions for the final workshop of the ''Biociclo'' research exchange between the Universidad de Concepcion and the Universitaet Karlsruhe. It reflects interdisciplinarity of the workshop's participants with contributed papers about Biomass Utilization Paths in Chile, Pyrolysis and Life-Cycle Assessment of Biomass and Logistic Concepts of Biomass Utilization Concepts. (orig.)

  12. Biomass Power Is Hobbling under Seducement

    Institute of Scientific and Technical Information of China (English)

    Zhao Ran; Ye Qing

    2007-01-01

    @@ Biomass power, just like other renewable power, is facing the difficulty of high price. Since last year, the state has issued a series of incentive policies which has stimulated the flourishing development of biomass power. In April 2007, the admeasurement of biomass power tariff surcharges was initiated, which once again lent allure to biomass power. People, however, may hardly reveal the underneath problems facing so many seducements.

  13. Microwave moisture measurements of flowing biomass

    Science.gov (United States)

    Production of pelleted biomass is a significant emerging industry in the United States. A primary quality attribute of pelleted biomass is moisture content. This parameter is critical in pricing, binding, combustion, and storage of pelleted biomass. In order to produce pellets of a high quality mois...

  14. Process and apparatus for conversion of biomass

    NARCIS (Netherlands)

    Bakker, R.R.C.; Hazewinkel, J.H.O.; Groenestijn, van J.W.

    2006-01-01

    The invention is directed to a process for the conversion of cellulosic biomass, in particular lignocellulose-containing biomass into fermentable sugars. The invention is further directed to apparatus suitable for carrying out such processes. According to the invention biomass is converted into ferm

  15. Switchgrass for Biomass Energy: Status and Progress

    Science.gov (United States)

    Switchgrass has been identified as a perennial biomass energy crop because it can produce high biomass yields on marginal land that is not suitable for grain crop production and provides many conservation benefits. The cellulose and hemi-cellulose of the biomass from switchgrass cell walls can be b...

  16. Trading biomass or GHG emission credits?

    NARCIS (Netherlands)

    Laurijssen, J; Faaij, A.P.C.

    2009-01-01

    Global biomass potentials are considerable but unequally distributed over the world. Countries with Kyoto targets could import biomass to substitute for fossil fuels or invest in bio-energy projects in the country of biomass origin and buy the credits (Clean Development Mechanism (CDM) and Joint

  17. Process and apparatus for conversion of biomass

    NARCIS (Netherlands)

    Bakker, R.R.C.; Hazewinkel, J.H.O.; Groenestijn, van J.W.

    2006-01-01

    The invention is directed to a process for the conversion of cellulosic biomass, in particular lignocellulose-containing biomass into fermentable sugars. The invention is further directed to apparatus suitable for carrying out such processes. According to the invention biomass is converted into

  18. Launching Plan B:Biomass Energy

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    China’s first biomass electricity company focuses on helping farmers as it strives to expand In April 2011,the world’s largest biomass power company,China National Bio Energy Co.Ltd.(NBE),began building a biomass power plant in Shangcai County of central China’s Henan Province.The new plant,due to reach

  19. Review and analysis of biomass gasification models

    DEFF Research Database (Denmark)

    Puig Arnavat, Maria; Bruno, Joan Carles; Coronas, Alberto

    2010-01-01

    The use of biomass as a source of energy has been further enhanced in recent years and special attention has been paid to biomass gasification. Due to the increasing interest in biomass gasification, several models have been proposed in order to explain and understand this complex process, and th...

  20. Evaluation of total aboveground biomass and total merchantable biomass in Missouri

    Science.gov (United States)

    Michael E. Goerndt; David R. Larsen; Charles D. Keating

    2014-01-01

    In recent years, the state of Missouri has been converting to biomass weight rather than volume as the standard measurement of wood for buying and selling sawtimber. Therefore, there is a need to identify accurate and precise methods of estimating whole tree biomass and merchantable biomass of harvested trees as well as total standing biomass of live timber for...

  1. Methods for producing and using densified biomass products containing pretreated biomass fibers

    Science.gov (United States)

    Dale, Bruce E.; Ritchie, Bryan; Marshall, Derek

    2015-05-26

    A process is provided comprising subjecting a quantity of plant biomass fibers to a pretreatment to cause at least a portion of lignin contained within each fiber to move to an outer surface of said fiber, wherein a quantity of pretreated tacky plant biomass fibers is produced; and densifying the quantity of pretreated tacky plant biomass fibers to produce one or more densified biomass particulates, wherein said biomass fibers are densified without using added binder.

  2. Biomass Business Opportunities Viet Nam

    Energy Technology Data Exchange (ETDEWEB)

    Zwebe, D. [SNV Netherlands Development Organisation, Ha Noi (Viet Nam)

    2012-03-15

    The goal of this survey is to provide a more specific and integral perspective in which niches, relevant policy development by the Vietnamese government, legislation and sustainability criteria are clearly addressed to benefit both the Dutch Private sector as well as to stimulate Dutch-Vietnamese cooperation and support the Vietnamese government in its search for tangible options to develop the desired enabling environment for a sustainable biomass/biofuel market. The following activities are defined to be executed to reach the goal of the project: Biomass availability in Vietnam (Chapter 2); Government of Vietnam and Energy (Chapter 3); The opportunities and barriers to enter the market in Vietnam (Chapter 4 and 5); Stakeholder analysis of the bio-energy sector (Chapter 6); and Recommendations (Chapter 7)

  3. Soybean biomass produced in Argentina

    DEFF Research Database (Denmark)

    Semino, Stella; Paul, Helena; Tomei, Julia

    Soybean biomass for biodiesel, produced in Argentina amongst other places, is considered by some to reduce greenhouse gas emissions and mitigate climate change when compared with fossil fuel. To ensure that the production of biofuels is ‘sustainable', EU institutions and national governments...... are currently designing certification schemes for the sustainable production of biomass. This paper questions the validity of proposed environmental standards, using the production of Argentine soybean as a case study. The production of soybean production is associated with profound environmental impacts...... generates emissions of N2O. The large quantity of substances, sprayed by terrestrial and aerial means, has negative impacts on biodiversity, water, soil, and human and animal health. The intensive production of soybeans also leads to social impacts, including loss of livelihoods and food sovereignty...

  4. Proximate analysis for amazon biomass

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Antonio Geraldo de Paula; Feitosa Netto, Genesio Batista; Nogueira, Manoel Fernandes Martins; Coutinho, Manoel Fernandes Martins; Coutinho, Hebert Willian Martins; Rendeiro, Goncalo [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Lab. de Engenharia Mecanica (LABGAS)], e-mail: ageraldo@ufpa.br, e-mail: mfmn@ufpa.br, e-mail: rendeiro@ufpa.br

    2006-07-01

    In order to asses the potentiality of Amazon biomass to generate power, either to supply electric energy to the grid or as fuel to plants supplying power for off-grid location, data for their proximate analysis must be available. A literature review on the subject indicated a lack of information and data concerning typical Amazon rain forest species. This work aimed to characterize (proximate analysis) 80 Amazon species in order to evaluate the energy resource from woody biomass wastes in Amazon region. Higher Heating Value, Carbon, Volatile and Ash contents were measured in a dry basis. The measurements were performed obeying the following Brazilian standards, NBR 6923, NBR 8112, NBR 8633, NBR 6922. (author)

  5. BIOMASS ENERGY AND ENERGY FORESTRY

    Directory of Open Access Journals (Sweden)

    Fahrettin Tilki

    2003-04-01

    Full Text Available Biomass fuels account for nearly 14% of the world’s energy. Energy forestry has been investigated since the mid-1960s to produce fiber for the paper and pulp industry. In the 1970s, following the oil crises, the emphasis switched to producing woody biomass for energy using fast-growing trees. Fastgrowing broadleaved trees, such as poplars and willows are grown at close spacing and under intensive management systems more akin to agriculture practice than forestry. In Turkey, rehabilitation studies in especially oak coppice stands are thought to be a part of the energy forestry, but the areas coppice stands grow on and species common in those areas are not suitable for modern energy forestry used in developed countries.

  6. Agricultural Residues and Biomass Energy Crops

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-06-01

    There are many opportunities to leverage agricultural resources on existing lands without interfering with production of food, feed, fiber, or forest products. In the recently developed advanced biomass feedstock commercialization vision, estimates of potentially available biomass supply from agriculture are built upon the U.S. Department of Agriculture’s (USDA’s) Long-Term Forecast, ensuring that existing product demands are met before biomass crops are planted. Dedicated biomass energy crops and agricultural crop residues are abundant, diverse, and widely distributed across the United States. These potential biomass supplies can play an important role in a national biofuels commercialization strategy.

  7. Chapter 8: Biomass Pyrolysis Oils

    Energy Technology Data Exchange (ETDEWEB)

    McCormick, Robert L.; Baldwin, Robert M.; Arbogast, Stephen; Bellman, Don; Paynter, Dave; Wykowski, Jim

    2016-09-06

    Fast pyrolysis is heating on the order of 1000 degrees C/s in the absence of oxygen to 40-600 degrees C, which causes decomposition of the biomass. Liquid product yield from biomass can be as much as 80% of starting dry weight and contains up to 75% of the biomass energy content. Other products are gases, primarily carbon monoxide, carbon dioxide, and methane, as well as solid char and ash. Residence time in the reactor is only 0.5-2 s so that relatively small, low-capital-cost reactors can be used. The low capital cost combined with greenhouse gas emission reductions relative to petroleum fuels of 50-95% makes pyrolysis an attractive process. The pyrolysis liquids have been investigated as a refinery feedstock and as stand-alone fuels. Utilization of raw pyrolysis oil has proven challenging. The organic fraction is highly corrosive because of its high organic acid content. High water content lowers the net heating value and can increase corrosivity. It can be poorly soluble in petroleum or petroleum products and can readily absorb water. Distillation residues can be as high as 50%, viscosity can be high, oils can exhibit poor stability in storage, and they can contain suspended solids. The ignition quality of raw pyrolysis oils is poor, with cetane number estimates ranging from 0 to 35, but more likely to be in the lower end of that range. While the use of raw pyrolysis oils in certain specific applications with specialized combustion equipment may be possible, raw oils must be significantly upgraded for use in on-highway spark-ignition (SI) and compression-ignition (CI) engines. Upgrading approaches most often involve catalytic hydrodeoxygenation, one of a class of reactions known as hydrotreating or hydroprocessing. This chapter discusses the properties of raw and upgraded pyrolysis oils, as well as the potential for integrating biomass pyrolysis with a petroleum refinery to significantly reduce the hydroprocessing cost.

  8. Biomass gasification for energy production

    Energy Technology Data Exchange (ETDEWEB)

    Lundberg, H.; Morris, M.; Rensfelt, E. [TPS Termiska Prosesser Ab, Nykoeping (Sweden)

    1997-12-31

    Biomass and waste are becoming increasingly interesting as fuels for efficient and environmentally sound power generation. Circulating fluidized bed (CFB) gasification for biomass and waste has been developed and applied to kilns both in the pulp and paper industry and the cement industry. A demonstration plant in Greve-in- Chianti, Italy includes two 15 MW{sub t}h RDF-fuelled CFB gasifiers of TPS design, the product gas from which is used in a cement kiln or in steam boiler for power generation. For CFB gasification of biomass and waste to reach a wider market, the product gas has to be cleaned effectively so that higher fuel to power efficiencies can be achieved by utilizing power cycles based on engines or gas turbines. TPS has developed both CFB gasification technology and effective secondary stage tar cracking technology. The integrated gasification - gas-cleaning technology is demonstrated today at pilot plant scale. To commercialise the technology, the TPS`s strategy is to first demonstrate the process for relatively clean fuels such as woody biomass and then extend the application to residues from waste recycling. Several demonstration projects are underway to commercialise TPS`s gasification and gas cleaning technology. In UK the ARBRE project developed by ARBRE Energy will construct a gasification plant at Eggborough, North Yorkshire, which will provide gas to a gas turbine and steam turbine generation system, producing 10 MW and exporting 8 Mw of electricity. It has been included in the 1993 tranche of the UK`s Non Fossil Fuel Obligation (NFFO) and has gained financial support from EC`s THERMIE programme as a targeted BIGCC project. (author)

  9. Finanziamento della produzione e "finance motive" in Keynes

    Directory of Open Access Journals (Sweden)

    Stefano Figuera

    2012-04-01

    Full Text Available The paper considers whether the Keynesian "finance motive" discussed in the 1937-39 articles represents a development of Keynes' monetary theory, as well as its connections with the analysis conducted in his previous writ-ings. In this study the financing of production is considered as a development of the Treatise on Money in the overall Keynesian thought. If elements were provided to complete the view of Keynes' theoretical work in the articles published after the General Theory, this development must be seen as strictly connected to the first of Keynes' main works. The consideration of Keynesian monetary analysis as a whole is also im-portant to understand better the basic role of the banking system. The issu-ing money from the banks is a tool for the start and the development of the productive process and a factor influencing the income distribution.  JEL Codes: B22, E12Keywords:

  10. Dual Fluidized Bed Biomass Gasification

    Energy Technology Data Exchange (ETDEWEB)

    None

    2005-09-30

    The dual fluidized bed reactor is a recirculating system in which one half of the unit operates as a steam pyrolysis device for biomass. The pyrolysis occurs by introducing biomass and steam to a hot fluidized bed of inert material such as coarse sand. Syngas is produced during the pyrolysis and exits the top of the reactor with the steam. A crossover arm, fed by gravity, moves sand and char from the pyrolyzer to the second fluidized bed. This sand bed uses blown air to combust the char. The exit stream from this side of the reactor is carbon dioxide, water and ash. There is a second gravity fed crossover arm to return sand to the pyrolysis side. The recirculating action of the sand and the char is the key to the operation of the dual fluidized bed reactor. The objective of the project was to design and construct a dual fluidized bed prototype reactor from literature information and in discussion with established experts in the field. That would be appropriate in scale and operation to measure the relative performance of the gasification of biomass and low ranked coals to produce a high quality synthesis gas with no dilution from nitrogen or combustion products.

  11. Engineered plant biomass feedstock particles

    Science.gov (United States)

    Dooley, James H [Federal Way, WA; Lanning, David N [Federal Way, WA; Broderick, Thomas F [Lake Forest Park, WA

    2012-04-17

    A new class of plant biomass feedstock particles characterized by consistent piece size and shape uniformity, high skeletal surface area, and good flow properties. The particles of plant biomass material having fibers aligned in a grain are characterized by a length dimension (L) aligned substantially parallel to the grain and defining a substantially uniform distance along the grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) normal to W and L. In particular, the L.times.H dimensions define a pair of substantially parallel side surfaces characterized by substantially intact longitudinally arrayed fibers, the W.times.H dimensions define a pair of substantially parallel end surfaces characterized by crosscut fibers and end checking between fibers, and the L.times.W dimensions define a pair of substantially parallel top and bottom surfaces. The L.times.W surfaces of particles with L/H dimension ratios of 4:1 or less are further elaborated by surface checking between longitudinally arrayed fibers. The length dimension L is preferably aligned within 30.degree. parallel to the grain, and more preferably within 10.degree. parallel to the grain. The plant biomass material is preferably selected from among wood, agricultural crop residues, plantation grasses, hemp, bagasse, and bamboo.

  12. Biomass gasification and energy production

    Energy Technology Data Exchange (ETDEWEB)

    Mahinpey, N.; Nikoo, M.B. [Regina Univ., SK (Canada). Faculty of Engineering

    2007-07-01

    The ASPEN PLUS simulation program was used to model an atmospheric fluidized bed biomass gasifier. The aim of the study was develop a simulation capable of accurately predicting steady state performance of the gasifier in relation to hydrodynamics and reaction kinetics. The influences of feed decomposition, volatile reactions, gas gasification and gas-solid separation were considered through modularized ASPEN PLUS models. The ASPEN PLUS yield reactor was used to simulate biomass feed decomposition. A separation column model was used to separate volatile materials and solids. Experimental data from a pine biomass gasification experiment conducted in a laboratory-scale fluidized bed gasifier was used to validate the simulation results. Good agreement was shown for gas composition, although carbon dioxide (CO{sub 2}) rates were slightly underestimated. The study also demonstrated that higher temperatures improved the gasification process and carbon conversion. The optimized gasification process produced more carbon monoxide (CO) and less CO{sub 2}. The introduction of lower temperature steam to the gasification process increased tar output. It was concluded that the conversion efficiency increased when the equivalence ratio was increased. 7 refs., 1 tab., 12 figs.

  13. PNEUMATIC CONVEYING OF BIOMASS PARTICLES: A REVIEW

    Institute of Scientific and Technical Information of China (English)

    Heping; Cui

    2006-01-01

    Processes involving biomass are of growing interest, but handling and conveying biomass particles are challenging due to the unusual physical properties of biomass particles. This paper reviews recent work on pneumatic conveying of biomass particles, especially agricultural particles and pulp fibres. Experimental work has been mainly carried out to determine a range of parameters, such as pressure drop, particle velocity, flow regime and electrostatic charging for both horizontal and vertical conveying. Models ranging from empirical to CFD models are also being developed. Difficulties in representing turbulence and interactions among biomass particles and between the particles and fluid have so far limited the success of advanced modeling. Further work is needed to improve understanding of multiphase biomass pneumatic conveying and to assist in the development of biomass energy and conversion processes.

  14. Sustainable Elastomers from Renewable Biomass.

    Science.gov (United States)

    Wang, Zhongkai; Yuan, Liang; Tang, Chuanbing

    2017-07-18

    Sustainable elastomers have undergone explosive growth in recent years, partly due to the resurgence of biobased materials prepared from renewable natural resources. However, mounting challenges still prevail: How can the chemical compositions and macromolecular architectures of sustainable polymers be controlled and broadened? How can their processability and recyclability be enabled? How can they compete with petroleum-based counterparts in both cost and performance? Molecular-biomass-derived polymers, such as polymyrcene, polymenthide, and poly(ε-decalactone), have been employed for constructing thermoplastic elastomers (TPEs). Plant oils are widely used for fabricating thermoset elastomers. We use abundant biomass, such as plant oils, cellulose, rosin acids, and lignin, to develop elastomers covering a wide range of structure-property relationships in the hope of delivering better performance. In this Account, recent progress in preparing monomers and TPEs from biomass is first reviewed. ABA triblock copolymer TPEs were obtained with a soft middle block containing a soybean-oil-based monomer and hard outer blocks containing styrene. In addition, a combination of biobased monomers from rosin acids and soybean oil was formulated to prepare triblock copolymer TPEs. Together with the above-mentioned approaches based on block copolymers, multigraft copolymers with a soft backbone and rigid side chains are recognized as the first-generation and second-generation TPEs, respectively. It has been recently demonstrated that multigraft copolymers with a rigid backbone and elastic side chains can also be used as a novel architecture of TPEs. Natural polymers, such as cellulose and lignin, are utilized as a stiff, macromolecular backbone. Cellulose/lignin graft copolymers with side chains containing a copolymer of methyl methacrylate and butyl acrylate exhibited excellent elastic properties. Cellulose graft copolymers with biomass-derived polymers as side chains were

  15. Lime pretreatment of lignocellulosic biomass

    Science.gov (United States)

    Chang, Shushien

    Lignocellulose is a valuable alternative energy source. The susceptibility of lignocellulosic biomass to enzymatic hydrolysis is constrained due to its structural features, so pretreatment is essential to enhance enzymatic digestibility. Of the chemicals used as pretreatment agents, it has been reported that alkalis improve biomass digestibility significantly. In comparison with other alkalis such as NaOH and ammonia, lime (calcium hydroxide) has many advantages; it is very inexpensive, is safe, and can be recovered by carbonating wash water. The effects of lime pretreatment were explored on switchgrass and poplar wood, representing herbaceous and woody biomass, respectively. The effects of pretreatment conditions (time, temperature, lime loading, water loading, particle size, and oxygen pressure) have been systematically studies. Lime alone enhances the digestibility of switchgrass significantly; under the recommended conditions, the 3-d total sugar (glucose + xylose) yields of lime-treated switchgrass were 7 times that of untreated sample. When treating poplar wood, lime must be combined with oxygen to achieve high digestibility; oxidative lime pretreatment increased the 3-d total sugar yield of poplar wood to 12 times that of untreated sample. In a fundamental study, to determine why lime pretreatment is effective, the effects of three structural features on enzymatic digestibility were studied: lignin content, acetyl content, and crystallinity index (CrI). Poplar wood was treated with peracetic acid, potassium hydroxide, and ball milling to produce model lignocelluloses with a broad spectrum of lignin contents, acetyl contents, and CrI, respectively. Enzymatic hydrolysis was performed on the model lignocelluloses to determine the digestibility. Correlations between lignin/carbohydrate ratio, acetyl/carbohydrate ratio, CrI and digestibility were developed. The 95% prediction intervals show that the correlations predict the 1-h and 3-d total sugar conversions of

  16. Biomass Energy Data Book: Edition 2

    Energy Technology Data Exchange (ETDEWEB)

    Wright, Lynn L [ORNL; Boundy, Robert Gary [ORNL; Badger, Philip C [ORNL; Perlack, Robert D [ORNL; Davis, Stacy Cagle [ORNL

    2009-12-01

    The Biomass Energy Data Book is a statistical compendium prepared and published by Oak Ridge National Laboratory (ORNL) under contract with the Biomass Program in the Energy Efficiency and Renewable Energy (EERE) program of the Department of Energy (DOE). Designed for use as a convenient reference, the book represents an assembly and display of statistics and information that characterize the biomass industry, from the production of biomass feedstocks to their end use, including discussions on sustainability. This is the second edition of the Biomass Energy Data Book which is only available online in electronic format. There are five main sections to this book. The first section is an introduction which provides an overview of biomass resources and consumption. Following the introduction to biomass, is a section on biofuels which covers ethanol, biodiesel and bio-oil. The biopower section focuses on the use of biomass for electrical power generation and heating. The fourth section is on the developing area of biorefineries, and the fifth section covers feedstocks that are produced and used in the biomass industry. The sources used represent the latest available data. There are also four appendices which include frequently needed conversion factors, a table of selected biomass feedstock characteristics, assumptions for selected tables and figures, and discussions on sustainability. A glossary of terms and a list of acronyms are also included for the reader's convenience.

  17. Biomass Energy Data Book: Edition 3

    Energy Technology Data Exchange (ETDEWEB)

    Boundy, Robert Gary [ORNL; Davis, Stacy Cagle [ORNL

    2010-12-01

    The Biomass Energy Data Book is a statistical compendium prepared and published by Oak Ridge National Laboratory (ORNL) under contract with the Biomass Program in the Energy Efficiency and Renewable Energy (EERE) program of the Department of Energy (DOE). Designed for use as a convenient reference, the book represents an assembly and display of statistics and information that characterize the biomass industry, from the production of biomass feedstocks to their end use, including discussions on sustainability. This is the third edition of the Biomass Energy Data Book which is only available online in electronic format. There are five main sections to this book. The first section is an introduction which provides an overview of biomass resources and consumption. Following the introduction to biomass, is a section on biofuels which covers ethanol, biodiesel and bio-oil. The biopower section focuses on the use of biomass for electrical power generation and heating. The fourth section is on the developing area of biorefineries, and the fifth section covers feedstocks that are produced and used in the biomass industry. The sources used represent the latest available data. There are also four appendices which include frequently needed conversion factors, a table of selected biomass feedstock characteristics, and discussions on sustainability. A glossary of terms and a list of acronyms are also included for the reader's convenience.

  18. Biomass Energy Data Book: Edition 1

    Energy Technology Data Exchange (ETDEWEB)

    Wright, Lynn L [ORNL; Boundy, Robert Gary [ORNL; Perlack, Robert D [ORNL; Davis, Stacy Cagle [ORNL; Saulsbury, Bo [ORNL

    2006-09-01

    The Biomass Energy Data Book is a statistical compendium prepared and published by Oak Ridge National Laboratory (ORNL) under contract with the Office of the Biomass Program and the Office of Planning, Budget and Analysis in the Department of Energy's Energy Efficiency and Renewable Energy (EERE) program. Designed for use as a desk-top reference, the book represents an assembly and display of statistics and information that characterize the biomass industry, from the production of biomass feedstocks to their end use. This is the first edition of the Biomass Energy Data Book and is currently only available online in electronic format. There are five main sections to this book. The first section is an introduction which provides an overview of biomass resources and consumption. Following the introduction to biomass is a section on biofuels which covers ethanol, biodiesel and BioOil. The biopower section focuses on the use of biomass for electrical power generation and heating. The fourth section is about the developing area of biorefineries, and the fifth section covers feedstocks that are produced and used in the biomass industry. The sources used represent the latest available data. There are also three appendices which include measures of conversions, biomass characteristics and assumptions for selected tables and figures. A glossary of terms and a list of acronyms are also included for the reader's convenience.

  19. Biomass Energy Data Book: Edition 4

    Energy Technology Data Exchange (ETDEWEB)

    Boundy, Robert Gary [ORNL; Diegel, Susan W [ORNL; Wright, Lynn L [ORNL; Davis, Stacy Cagle [ORNL

    2011-12-01

    The Biomass Energy Data Book is a statistical compendium prepared and published by Oak Ridge National Laboratory (ORNL) under contract with the Biomass Program in the Energy Efficiency and Renewable Energy (EERE) program of the Department of Energy (DOE). Designed for use as a convenient reference, the book represents an assembly and display of statistics and information that characterize the biomass industry, from the production of biomass feedstocks to their end use, including discussions on sustainability. This is the fourth edition of the Biomass Energy Data Book which is only available online in electronic format. There are five main sections to this book. The first section is an introduction which provides an overview of biomass resources and consumption. Following the introduction to biomass, is a section on biofuels which covers ethanol, biodiesel and bio-oil. The biopower section focuses on the use of biomass for electrical power generation and heating. The fourth section is on the developing area of biorefineries, and the fifth section covers feedstocks that are produced and used in the biomass industry. The sources used represent the latest available data. There are also two appendices which include frequently needed conversion factors, a table of selected biomass feedstock characteristics, and discussions on sustainability. A glossary of terms and a list of acronyms are also included for the reader's convenience.

  20. Biomass - Overview of Swiss Research Programme 2003; Biomasse

    Energy Technology Data Exchange (ETDEWEB)

    Binggeli, D.; Guggisberg, B.

    2003-07-01

    This overview for the Swiss Federal Office of Energy (SFOE) discusses the results obtained in 2003 in various research projects worked on in Switzerland on the subject of biomass. In the biomass combustion area, subjects discussed include system optimisation for automatic firing, combustion particles, low-particle pellet furnaces, design and optimisation of wood-fired storage ovens, efficiency of filtering techniques and methane generation from wood. Also, an accredited testing centre for wood furnaces is mentioned and measurements made on an installation are presented. As far as the fermentation of biogenic wastes is concerned, biogas production from dairy-product wastes is described. Other projects discussed include a study on eco-balances of energy products, certification and marketing of biogas, evaluation of membranes, a measurement campaign for solar sludge-drying, the operation of a percolator installation for the treatment of bio-wastes, the effects of compost on the environment and the fermentation of coffee wastes. Also, statistics on biogas production in 2002 is looked at. Finally, a preliminary study on biofuels is presented.

  1. Biomass proximate analysis using thermogravimetry.

    Science.gov (United States)

    García, Roberto; Pizarro, Consuelo; Lavín, Antonio G; Bueno, Julio L

    2013-07-01

    This work proposes a 25 min-last thermogravimetric method as a tool to determine biomass sample's proximate analysis data (moisture, ash, volatile matter and fixed carbon contents) just by direct measure of weight changes on each sample's TG chart. Compared with international standards commonly used to that aim, TG is a faster and easier to develop technique. Obtained results were satisfactory, with AEE under 6% for moisture and volatile matter, close to 10% for fixed carbon determination and AAD of 1.6 points for ash content.

  2. Leaching From Biomass Gasification Residues

    DEFF Research Database (Denmark)

    Allegrini, Elisa; Boldrin, Alessio; Polletini, A.

    2011-01-01

    The aim of the present work is to attain an overall characterization of solid residues from biomass gasification. Besides the determination of chemical and physical properties, the work was focused on the study of leaching behaviour. Compliance and pH-dependence leaching tests coupled...... with geochemical modelling were carried out both on fresh and aged samples. The results showed that the material is comparable to residues from wood combustion and the leaching behaviour was dominated by Ca-containing minerals and solid solutions. Heavy metals were detected in very low concentrations in the bulk...

  3. Fuels from biomass program. Program summary

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-01-01

    An overview of the ongoing research, development, and demonstration efforts of the period Oct. 1, 1976--Sept. 30, 1977 is presented. Accomplishments are highlighted and plans for continued activities are included. Discussion is presented under the following section headings: the Fuels from Biomass Program; organizational and functional responsibilities; program funding; fiscal year 1977 summary tables; current projects: production and collection of biomass and conversion of biomass; bibliography; index of contractors; and, appendix--unsolicited proposal requirements. (JGB)

  4. 3rd annual biomass energy systems conference

    Energy Technology Data Exchange (ETDEWEB)

    1979-10-01

    The main objectives of the 3rd Annual Biomass Energy Systems Conference were (1) to review the latest research findings in the clean fuels from biomass field, (2) to summarize the present engineering and economic status of Biomass Energy Systems, (3) to encourage interaction and information exchange among people working or interested in the field, and (4) to identify and discuss existing problems relating to ongoing research and explore opportunities for future research. Abstracts for each paper presented were edited separately. (DC)

  5. Biomass Compositional Analysis Laboratory (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2014-07-01

    At the Biomass Compositional Analysis Laboratory, NREL scientists have more than 20 years of experience supporting the biomass conversion industry. They develop, refine, and validate analytical methods to determine the chemical composition of biomass samples before, during, and after conversion processing. These high-quality compositional analysis data are used to determine feedstock compositions as well as mass balances and product yields from conversion processes.

  6. Estimates of US biomass energy consumption 1992

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-06

    This report is the seventh in a series of publications developed by the Energy Information Administration (EIA) to quantify the biomass-derived primary energy used by the US economy. It presents estimates of 1991 and 1992 consumption. The objective of this report is to provide updated estimates of biomass energy consumption for use by Congress, Federal and State agencies, biomass producers and end-use sectors, and the public at large.

  7. Simulation study on combustion of biomass

    Science.gov (United States)

    Zhao, M. L.; Liu, X.; Cheng, J. W.; Liu, Y.; Jin, Y. A.

    2017-01-01

    Biomass combustion is the most common energy conversion technology, offering the advantages of low cost, low risk and high efficiency. In this paper, the transformation and transfer of biomass in the process of combustion are discussed in detail. The process of furnace combustion and gas phase formation was analyzed by numerical simulation. The experimental results not only help to optimize boiler operation and realize the efficient combustion of biomass, but also provide theoretical basis for the improvement of burner technology.

  8. Bamboo: An Overlooked Biomass Resource?

    Energy Technology Data Exchange (ETDEWEB)

    Scurlock, J.M.O.

    2000-02-01

    Bamboo is the common term applied to a broad group (1250 species) of large woody grasses, ranging from 10 cm to 40 m in height. Already in everyday use by about 2.5 billion people, mostly for fiber and food within Asia, bamboo may have potential as a bioenergy or fiber crop for niche markets, although some reports of its high productivity seem to be exaggerated. Literature on bamboo productivity is scarce, with most reports coming from various parts of Asia. There is little evidence overall that bamboo is significantly more productive than many other candidate bioenergy crops, but it shares a number of desirable fuel characteristics with certain other bioenergy feedstocks, such as low ash content and alkali index. Its heating value is lower than many woody biomass feedstocks but higher than most agricultural residues, grasses and straws. Although non-fuel applications of bamboo biomass may be actually more profitable than energy recovery, there may also be potential for co-productio n of bioenergy together with other bamboo processing. A significant drawback is the difficulty of selective breeding, given the lack of knowledge of flowering physiology. Further research is also required on propagation techniques, establishment and stand management, and mechanized harvesting needs to be developed.

  9. Engineered plant biomass feedstock particles

    Science.gov (United States)

    Dooley, James H.; Lanning, David N.; Broderick, Thomas F.

    2011-10-11

    A novel class of flowable biomass feedstock particles with unusually large surface areas that can be manufactured in remarkably uniform sizes using low-energy comminution techniques. The feedstock particles are roughly parallelepiped in shape and characterized by a length dimension (L) aligned substantially with the grain direction and defining a substantially uniform distance along the grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) normal to W and L. The particles exhibit a disrupted grain structure with prominent end and surface checks that greatly enhances their skeletal surface area as compared to their envelope surface area. The L.times.H dimensions define a pair of substantially parallel side surfaces characterized by substantially intact longitudinally arrayed fibers. The W.times.H dimensions define a pair of substantially parallel end surfaces characterized by crosscut fibers and end checking between fibers. The L.times.W dimensions define a pair of substantially parallel top surfaces characterized by some surface checking between longitudinally arrayed fibers. The feedstock particles are manufactured from a variety of plant biomass materials including wood, crop residues, plantation grasses, hemp, bagasse, and bamboo.

  10. Lignocellulosic Biomass Pretreatment Using AFEX

    Science.gov (United States)

    Balan, Venkatesh; Bals, Bryan; Chundawat, Shishir P. S.; Marshall, Derek; Dale, Bruce E.

    Although cellulose is the most abundant organic molecule, its susceptibility to hydrolysis is restricted due to the rigid lignin and hemicellulose protection surrounding the cellulose micro fibrils. Therefore, an effective pretreatment is necessary to liberate the cellulose from the lignin-hemicellulose seal and also reduce cellulosic crystallinity. Some of the available pretreatment techniques include acid hydrolysis, steam explosion, ammonia fiber expansion (AFEX), alkaline wet oxidation, and hot water pretreatment. Besides reducing lignocellulosic recalcitrance, an ideal pretreatment must also minimize formation of degradation products that inhibit subsequent hydrolysis and fermentation. AFEX is an important pretreatment technology that utilizes both physical (high temperature and pressure) and chemical (ammonia) processes to achieve effective pretreatment. Besides increasing the surface accessibility for hydrolysis, AFEX promotes cellulose decrystallization and partial hemicellulose depolymerization and reduces the lignin recalcitrance in the treated biomass. Theoretical glucose yield upon optimal enzymatic hydrolysis on AFEX-treated corn stover is approximately 98%. Furthermore, AFEX offers several unique advantages over other pretreatments, which include near complete recovery of the pretreatment chemical (ammonia), nutrient addition for microbial growth through the remaining ammonia on pretreated biomass, and not requiring a washing step during the process which facilitates high solid loading hydrolysis. This chapter provides a detailed practical procedure to perform AFEX, design the reactor, determine the mass balances, and conduct the process safely.

  11. Lignocellulosic biomass pretreatment using AFEX.

    Science.gov (United States)

    Balan, Venkatesh; Bals, Bryan; Chundawat, Shishir P S; Marshall, Derek; Dale, Bruce E

    2009-01-01

    Although cellulose is the most abundant organic molecule, its susceptibility to hydrolysis is restricted due to the rigid lignin and hemicellulose protection surrounding the cellulose micro fibrils. Therefore, an effective pretreatment is necessary to liberate the cellulose from the lignin-hemicellulose seal and also reduce cellulosic crystallinity. Some of the available pretreatment techniques include acid hydrolysis, steam explosion, ammonia fiber expansion (AFEX), alkaline wet oxidation, and hot water pretreatment. Besides reducing lignocellulosic recalcitrance, an ideal pretreatment must also minimize formation of degradation products that inhibit subsequent hydrolysis and fermentation. AFEX is an important pretreatment technology that utilizes both physical (high temperature and pressure) and chemical (ammonia) processes to achieve effective pretreatment. Besides increasing the surface accessibility for hydrolysis, AFEX promotes cellulose decrystallization and partial hemicellulose depolymerization and reduces the lignin recalcitrance in the treated biomass. Theoretical glucose yield upon optimal enzymatic hydrolysis on AFEX-treated corn stover is approximately 98%. Furthermore, AFEX offers several unique advantages over other pretreatments, which include near complete recovery of the pretreatment chemical (ammonia), nutrient addition for microbial growth through the remaining ammonia on pretreated biomass, and not requiring a washing step during the process which facilitates high solid loading hydrolysis. This chapter provides a detailed practical procedure to perform AFEX, design the reactor, determine the mass balances, and conduct the process safely.

  12. Producing liquid fuels from biomass

    Science.gov (United States)

    Solantausta, Yrjo; Gust, Steven

    The aim of this survey was to compare, on techno-economic criteria, alternatives of producing liquid fuels from indigenous raw materials in Finland. Another aim was to compare methods under development and prepare a proposal for steering research related to this field. Process concepts were prepared for a number of alternatives, as well as analogous balances and production and investment cost assessments for these balances. Carbon dioxide emissions of the alternatives and the price of CO2 reduction were also studied. All the alternatives for producing liquid fuels from indigenous raw materials are utmost unprofitable. There are great differences between the alternatives. While the production cost of ethanol is 6 to 9 times higher than the market value of the product, the equivalent ratio for substitute fuel oil produced from peat by pyrolysis is 3 to 4. However, it should be borne in mind that the technical uncertainties related to the alternatives are of different magnitude. Production of ethanol from barley is of commercial technology, while biomass pyrolysis is still under development. If the aim is to reach smaller carbon dioxide emissions by using liquid biofuels, the most favorable alternative is pyrolysis oil produced from wood. Fuels produced from cultivated biomass are more expensive ways of reducing CO2 emissions. Their potential of reducing CO2 emissions in Finland is insignificant. Integration of liquid fuel production to some other production line is more profitable.

  13. Engineered plant biomass feedstock particles

    Science.gov (United States)

    Dooley, James H [Federal Way, WA; Lanning, David N [Federal Way, WA; Broderick, Thomas F [Lake Forest Park, WA

    2011-10-18

    A novel class of flowable biomass feedstock particles with unusually large surface areas that can be manufactured in remarkably uniform sizes using low-energy comminution techniques. The feedstock particles are roughly parallelepiped in shape and characterized by a length dimension (L) aligned substantially with the grain direction and defining a substantially uniform distance along the grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) normal to W and L. The particles exhibit a disrupted grain structure with prominent end and surface checks that greatly enhances their skeletal surface area as compared to their envelope surface area. The L.times.H dimensions define a pair of substantially parallel side surfaces characterized by substantially intact longitudinally arrayed fibers. The W.times.H dimensions define a pair of substantially parallel end surfaces characterized by crosscut fibers and end checking between fibers. The L.times.W dimensions define a pair of substantially parallel top surfaces characterized by some surface checking between longitudinally arrayed fibers. At least 80% of the particles pass through a 1/4 inch screen having a 6.3 mm nominal sieve opening but are retained by a No. 10 screen having a 2 mm nominal sieve opening. The feedstock particles are manufactured from a variety of plant biomass materials including wood, crop residues, plantation grasses, hemp, bagasse, and bamboo.

  14. Combustion, pyrolysis, gasification, and liquefaction of biomass

    Energy Technology Data Exchange (ETDEWEB)

    Reed, T.B.

    1980-09-01

    All the products now obtained from oil can be provided by thermal conversion of the solid fuels biomass and coal. As a feedstock, biomass has many advantages over coal and has the potential to supply up to 20% of US energy by the year 2000 and significant amounts of energy for other countries. However, it is imperative that in producing biomass for energy we practice careful land use. Combustion is the simplest method of producing heat from biomass, using either the traditional fixed-bed combustion on a grate or the fluidized-bed and suspended combustion techniques now being developed. Pyrolysis of biomass is a particularly attractive process if all three products - gas, wood tars, and charcoal - can be used. Gasification of biomass with air is perhaps the most flexible and best-developed process for conversion of biomass to fuel today, yielding a low energy gas that can be burned in existing gas/oil boilers or in engines. Oxygen gasification yields a gas with higher energy content that can be used in pipelines or to fire turbines. In addition, this gas can be used for producing methanol, ammonia, or gasoline by indirect liquefaction. Fast pyrolysis of biomass produces a gas rich in ethylene that can be used to make alcohols or gasoline. Finally, treatment of biomass with high pressure hydrogen can yield liquid fuels through direct liquefaction.

  15. Theme E: Forest Biomass and Bioenergy

    DEFF Research Database (Denmark)

    Bentsen, Niclas Scott; Stupak, Inge; Smith, C

    2014-01-01

    , evaluate and compare forest biomass sourcing potentials and associated forest sustainability challenges in Europe, Russia, Africa, North and South America, under a scenario where international demand for energy wood continue to increase. We focused on environmental sustainability criteria (GHG emission......Several countries in the world have policies for increased use of biomass for energy and biomaterials. It is likely that such policies will lead to increased international demand for wood and increased pressure on the world’s forests. Concerns for forest sustainability have been expressed...... challenges in the different regions for consideration by institutions developing energy biomass sourcing polices and biomass sustainability criteria in the public and private sector....

  16. EERC Center for Biomass Utilization 2006

    Energy Technology Data Exchange (ETDEWEB)

    Zygarlicke, Christopher J. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Hurley, John P. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Aulich, Ted R. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Folkedahl, Bruce C. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Strege, Joshua R. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Patel, Nikhil [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center; Shockey, Richard E. [Univ. of North Dakota, Grand Forks, ND (United States). Energy and Environmental Research Center

    2009-05-27

    The Center for Biomass Utilization® 2006 project at the Energy & Environmental Research Center (EERC) consisted of three tasks related to applied fundamental research focused on converting biomass feedstocks to energy, liquid transportation fuels, and chemicals. Task 1, entitled Thermochemical Conversion of Biomass to Syngas and Chemical Feedstocks, involved three activities. Task 2, entitled Crop Oil Biorefinery Process Development, involved four activities. Task 3, entitled Management, Education, and Outreach, focused on overall project management and providing educational outreach related to biomass technologies through workshops and conferences.

  17. Co-firing of biomass with coal: constraints and role of biomass pretreatment

    NARCIS (Netherlands)

    Maciejewska, A.K.; Veringa, H.; Sanders, J.P.M.; Peteves, S.D.

    2006-01-01

    This report aims at introducing the aspects of co-firing of biomass with coal. The main focus is given to problems and constraints related to utilizing biomass together with coal for power generation, and the potential of biomass pre-treatment in mitigating these constraints. The work is based on a

  18. Residue distribution and biomass recovery following biomass harvest of plantation pine

    Science.gov (United States)

    Johnny Grace III; John Klepac; S. Taylor; Dana Mitchell

    2016-01-01

    Forest biomass is anticipated to play a significant role in addressing an alternative energy supply. However, the efficiencies of current state-of-the-art recovery systems operating in forest biomass harvests are still relatively unknown. Forest biomass harvest stands typically have higher stand densities and smaller diameter trees than conventional stands which may...

  19. Supercritical water gasification of biomass: an experimental study of model compounds and potential biomass feeds

    NARCIS (Netherlands)

    Chakinala, Anand Gupta

    2013-01-01

    Gasification of biomass in supercritical water is a complex process. In supercritical water ideally the biomass structure and the larger molecules are broken down into smaller, gaseous components under the influence of radicals. However, the biomass is normally fed to the system at low temperature a

  20. Biomass Supply and Trade Opportunities of Preprocessed Biomass for Power Generation

    NARCIS (Netherlands)

    Batidzirai, B.; Junginger, M.; Klemm, M.; Schipfer, F.; Thrän, D.

    2016-01-01

    International trade of solid biomass is expected to increase significantly given the global distribution of biomass resources and anticipated expansion of bioenergy deployment in key global power markets. Given the unique characteristics of biomass, its long-distance trade requires optimized logisti

  1. Co-firing of biomass with coal: constraints and role of biomass pretreatment

    NARCIS (Netherlands)

    Maciejewska, A.K.; Veringa, H.; Sanders, J.P.M.; Peteves, S.D.

    2006-01-01

    This report aims at introducing the aspects of co-firing of biomass with coal. The main focus is given to problems and constraints related to utilizing biomass together with coal for power generation, and the potential of biomass pre-treatment in mitigating these constraints. The work is based on a

  2. Biomass in a sustainable energy system

    Energy Technology Data Exchange (ETDEWEB)

    Boerjesson, Paal

    1998-04-01

    In this thesis, aspects of an increase in the utilization of biomass in the Swedish energy system are treated. Modern bioenergy systems should be based on high energy and land use efficiency since biomass resources and productive land are limited. The energy input, including transportation, per unit biomass produced is about 4-5% for logging residues, straw and short rotation forest (Salix). Salix has the highest net energy yield per hectare among the various energy crops cultivated in Sweden. The CO{sub 2} emissions from the production and transportation of logging residues, straw and Salix, are equivalent to 2-3% of those from a complete fuel-cycle for coal. Substituting biomass for fossil fuels in electricity and heat production is, in general, less costly and leads to a greater CO{sub 2} reduction per unit biomass than substituting biomass derived transportation fuels for petrol or diesel. Transportation fuels produced from cellulosic biomass provide larger and less expensive CO{sub 2} emission reductions than transportation fuels from annual crops. Swedish CO{sub 2} emissions could be reduced by about 50% from the present level if fossil fuels are replaced and the energy demand is unchanged. There is a good balance between potential regional production and utilization of biomass in Sweden. Future biomass transportation distances need not be longer than, on average, about 40 km. About 22 TWh electricity could be produced annually from biomass in large district heating systems by cogeneration. Cultivation of Salix and energy grass could be utilized to reduce the negative environmental impact of current agricultural practices, such as the emission of greenhouse gases, nutrient leaching, decreased soil fertility and erosion, and for the treatment of municipal waste and sludge, leading to increased recirculation of nutrients. About 20 TWh biomass could theoretically be produced per year at an average cost of less than 50% of current production cost, if the economic

  3. Conservative species drive biomass productivity in tropical dry forests

    NARCIS (Netherlands)

    Prado-Junior, Jamir A.; Schiavini, Ivan; Vale, Vagner S.; Sande, van der Masha T.; Lohbeck, Madelon; Poorter, Lourens

    2016-01-01

    Forests account for a substantial part of the terrestrial biomass storage and productivity. To better understand forest productivity, we need to disentangle the processes underlying net biomass change. We tested how above-ground net biomass change and its underlying biomass dynamics (biomass recr

  4. 77 FR 47047 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2012-08-07

    ... of Energy Efficiency and Renewable Energy Biomass Research and Development Technical Advisory... open meeting. SUMMARY: This notice announces an open meeting of the Biomass Research ] and Development... Biomass R&D Activities Update on DOE Biomass R&D Activities Review of the recently awarded Biomass...

  5. Gasohol - Analysis and biomass alternatives

    Science.gov (United States)

    1980-11-01

    The economics of fermentation ethanol as a near-term alternative to liquid hydrocarbon fuels are analyzed and alternatives to grain-fermented ethanol are examined. Based on estimates of raw material and production costs and energy consumption, it is shown that net production costs for alcohol fuel from corn amount to $2.14/gallon, with no significant net consumption or gain in energy. It is also pointed out that the use of grain for alcohol production will influence quantities available for livestock production and export, and that land available for grain production is limited. Consideration is then given to the economic potential of using cellulosic biomass from agricultural and forest residues in the production of ethanol fuels and coal gasification for methanol production, and it is pointed out that these alternatives offer economic, energy and oil-savings advantages over ethanol production from grains.

  6. Methane production from plant biomass

    Energy Technology Data Exchange (ETDEWEB)

    Zauner, E.

    1985-01-01

    Methane fermentations of plant biomass were performed to increase basic knowledge necessary for development of suitable conversion technologies. Effects of bacterial inoculants, substrate compounds and varied process conditions were analyzed in batch and continuous fermentation experiments. Use of enriched bacterial populations precultured and adapted to plant materials was proved to be advantageous for inoculation. Methane yields and productivities as well as chemical and bacterial composition of digester fluids were determined at various loading rates and retention times during fermentation of different grass and maize silages. Recycling for favorable amounts of decomposed effluent for neutralization of supplied acid raw materials was important to achieve high methane yields. Quantity and composition of acido-, aceto- and methanogenic bacteria were not essentially influenced by changed fermentation conditions. Results of these laboratory examinations have to be completed by long run and scale up experiments to develop control parameters for plant biogas digesters.

  7. SPECIFIC EMISSIONS FROM BIOMASS COMBUSTION

    Directory of Open Access Journals (Sweden)

    Pavel Skopec

    2014-02-01

    Full Text Available This paper deals with determining the specific emissions from the combustion of two kinds of biomass fuels in a small-scale boiler. The tested fuels were pellets made of wood and pellets made of rape plant straw. In order to evaluate the specific emissions, several combustion experiments were carried out using a commercial 25 kW pellet-fired boiler. The specific emissions of CO, SO2 and NOx were evaluated in relation to a unit of burned fuel, a unit of calorific value and a unit of produced heat. The specific emissions were compared with some data acquired from the reference literature, with relatively different results. The differences depend mainly on the procedure used for determining the values, and references provide no information about this. Although some of our experimental results may fit with one of the reference sources, they do not fit with the other. The reliability of the references is therefore disputable.

  8. Improvements of biomass deconstruction enzymes

    Energy Technology Data Exchange (ETDEWEB)

    Sale, K. L.

    2012-03-01

    Sandia National Laboratories and DSM Innovation, Inc. collaborated on the investigation of the structure and function of cellulases from thermophilic fungi. Sandia's role was to use its expertise in protein structure determination and X-ray crystallography to solve the structure of these enzymes in their native state and in their substrate and product bound states. Sandia was also tasked to work with DSM to use the newly solved structure to, using computational approaches, analyze enzyme interactions with both bound substrate and bound product; the goal being to develop approaches for rationally designing improved cellulases for biomass deconstruction. We solved the structures of five cellulases from thermophilic fungi. Several of these were also solved with bound substrate/product, which allowed us to predict mutations that might enhance activity and stability.

  9. Entrained Flow Gasification of Biomass

    DEFF Research Database (Denmark)

    Qin, Ke

    concentration, larger feeder gas flow, and longer residence time. Wood, straw, and lignin had similar gasification behavior except with regard to soot formation. The soot yield was lowest during straw gasification possibly because of its high potassium content. The equilibrium product compositions under...... from straw gasification had quite low content of soot while high contents of volatilizable KCl and K2SO4, and thereby appeared as irregular crystals (> 100 nm). During lignin gasification, the filter sample mainly consisted of soot and nonvolatilizable inorganic matter. The parent wood particles...... the wood soot with respect to both oxidation and CO2 gasification. Besides, the wood soot produced at higher temperature was more reactive than the soot produced at lower temperature. Biomass and coal co-gasification experiments were performed in the same entrained flow reactor. The effect of mixing ratio...

  10. Mini-biomass electric generation

    Energy Technology Data Exchange (ETDEWEB)

    Elliot, G. [International Applied Engineering, Inc., Atlanta, GA (United States)

    1997-12-01

    Awareness of the living standards achieved by others has resulted in a Russian population which is yearning for a higher standard of living. Such a situation demands access to affordable electricity in remote areas. Remote energy requirements creates the need to transport power or fossil fuels over long distances. Application of local renewable energy resources could eliminate the need for and costs of long distance power supply. Vast forest resources spread over most of Russia make biomass an ideal renewable energy candidate for many off-grid villages. The primary objective for this preliminary evaluation is to examine the economic feasibility of replacing distillate and gasoline fuels with local waste biomass as the primary fuel for village energy in outlying regions of Russia. Approximately 20 million people live in regions where Russia`s Unified Electric System grid does not penetrate. Most of these people are connected to smaller independent power grids, but approximately 8 million Russians live in off-grid villages and small towns served by stand-alone generation systems using either diesel fuel or gasoline. The off-grid villages depend on expensive distillate fuels and gasoline for combustion in small boilers and engines. These fuels are used for both electricity generation and district heating. Typically, diesel generator systems with a capacity of up to 1 MW serve a collective farm, settlement and their rural enterprises (there are an estimated 10,000 such systems in Russia). Smaller gasoline-fueled generator systems with capacities in the range of 0.5 - 5 kW serve smaller farms or rural enterprises (there are about 60,000 such systems in Russia).

  11. Processes for pretreating lignocellulosic biomass: A review

    Energy Technology Data Exchange (ETDEWEB)

    McMillan, J D

    1992-11-01

    This paper reviews existing and proposed pretreatment processes for biomass. The focus is on the mechanisms by which the various pretreatments act and the influence of biomass structure and composition on the efficacy of particular pretreatment techniques. This analysis is used to identify pretreatment technologies and issues that warrant further research.

  12. SERI Biomass Program. FY 1983 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Corder, R.E.; Hill, A.M.; Lindsey, H.; Lowenstein, M.Z.; McIntosh, R.P.

    1984-02-01

    This report summarizes the progress and research accomplishments of the SERI Biomass Program during FY 1983. The SERI Biomass Program consists of three elements: Aquatic Species, Anaerobic Digestion, and Photo/Biological Hydrogen. Each element has been indexed separately. 2 references, 44 figures, 22 tables.

  13. Process and apparatus for conversion of biomass

    NARCIS (Netherlands)

    Bakker, R.R.C.; Hazewinkel, J.H.O.; Groenestijn, van J.W.

    2006-01-01

    The invention is directed to a process for the conversion of biomass, in particular lignocellulose-containing biomass into a product that may be further processes in a fermentation step. The invention is further directed to apparatus suitable for carrying out such processes. According to the inventi

  14. Quality Determination of Biomass for Combustion

    DEFF Research Database (Denmark)

    Liu, Na; Jørgensen, Uffe; Lærke, Poul Erik

    2013-01-01

    A high content of minerals in biomass feedstock may cause fouling, slagging, and corrosion in the furnace during combustion. Here, a new pressurized microwave digestion method for biomass digestion prior to elemental analysis is presented. This high-throughput method is capable of processing...

  15. Materials for Waste Incinerators and Biomass Plants

    DEFF Research Database (Denmark)

    Rademakers, P.; Grossmann, G.; Karlsson, A.

    1998-01-01

    This paper reviews the projects of the sub-package on waste incineration and biomass firing carried out within COST 501 Round III, Work Package 13.......This paper reviews the projects of the sub-package on waste incineration and biomass firing carried out within COST 501 Round III, Work Package 13....

  16. Modeling integrated biomass gasification business concepts

    Science.gov (United States)

    Peter J. Ince; Ted Bilek; Mark A. Dietenberger

    2011-01-01

    Biomass gasification is an approach to producing energy and/or biofuels that could be integrated into existing forest product production facilities, particularly at pulp mills. Existing process heat and power loads tend to favor integration at existing pulp mills. This paper describes a generic modeling system for evaluating integrated biomass gasification business...

  17. Structural Studies of Biomass Degrading Enzyme Systems

    Energy Technology Data Exchange (ETDEWEB)

    Lunin, Vladimir V.; Alahuhta, Markus; Brunecky, Roman; Donohoe, Bryon; Xu, Qi; Bomble, Yannick J.; Himmel, Michael E.

    2014-08-05

    Renewable energy today comprises wind, photovoltaics, geothermal, and biofuels. Biomass is the leading source of renewable, sustainable energy used for the production of liquid transportation fuels. While the focus is shifting today from the ethanol towards next generation or advanced biofuels the real challenge however remains the same: reducing the recalcitrance of biomass to deconstruction, which yields the sugars needed for further processing.

  18. Biomass Program 2007 Accomplishments - Full Report

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2009-10-27

    The Office of Energy Efficiency and Renewable Energy's (EERE’s) Biomass Program works with industry, academia and its national laboratory partners on a balanced portfolio of research in biomass feedstocks and conversion technologies. This document provides Program accomplishments for 2007.

  19. Biomass electrochemistry : from cellulose to sorbitol

    NARCIS (Netherlands)

    Kwon, Youngkook

    2013-01-01

    The primary goal of this thesis is to study the potential role of electrochemistry in finding new routes for sustainable chemicals from biomass in aqueous-phase solutions. In order to assess the potential of electrochemistry in biomass conversion, we developed an online HPLC system by using a

  20. How biomass composition determines protein extractability

    NARCIS (Netherlands)

    Sari, Y.W.; Syafitri, U.; Sanders, J.P.M.; Bruins, M.E.

    2015-01-01

    Biomass consists of a complex mixture of different components, of which protein potentially has a high added value for biorefinery. In this study, protein extractability of different types of biomass, mostly by-products, was analyzed. Protein yield obtained from a three step extraction using alkali

  1. Stabilization of biomass-derived pyrolysis oils

    NARCIS (Netherlands)

    Venderbosch, R. H.; Ardiyanti, A. R.; Wildschut, J.; Oasmaa, A.; Heeres, H. J.

    2010-01-01

    BACKGROUND: Biomass is the only renewable feedstock containing carbon, and therefore the only alternative to fossil-derived crude oil derivatives. However, the main problems concerning the application of biomass for biofuels and bio-based chemicals are related to transport and handling, the limited

  2. Process and apparatus for conversion of biomass

    NARCIS (Netherlands)

    Bakker, R.R.C.; Hazewinkel, J.H.O.; Groenestijn, van J.W.

    2006-01-01

    The invention is directed to a process for the conversion of biomass, in particular lignocellulose-containing biomass into a product that may be further processes in a fermentation step. The invention is further directed to apparatus suitable for carrying out such processes. According to the

  3. Trends and Challenges in Catalytic Biomass Conversion

    DEFF Research Database (Denmark)

    Osmundsen, Christian Mårup; Egeblad, Kresten; Taarning, Esben

    2013-01-01

    . The conversion of biomass-derived substrates, such as glycerol, by hydrogenolysis to the important chemicals ethylene glycol and propane diols. Secondly, the conversion of carbohydrates by Lewis acidic zeolites to yield alkyl lactates, and finally the conversion of lignin, an abundant low value source of biomass...

  4. Processes for pretreating lignocellulosic biomass: A review

    Energy Technology Data Exchange (ETDEWEB)

    McMillan, J.D.

    1992-11-01

    This paper reviews existing and proposed pretreatment processes for biomass. The focus is on the mechanisms by which the various pretreatments act and the influence of biomass structure and composition on the efficacy of particular pretreatment techniques. This analysis is used to identify pretreatment technologies and issues that warrant further research.

  5. Anaerobic digestion in sustainable biomass chains

    NARCIS (Netherlands)

    Pabon Pereira, C.P.

    2009-01-01

    This thesis evaluates the potential contribution of anaerobic digestion (AD) to the sustainability of biomass chains. Results provide insights in the technological potential to recover energy and valuable by-products from energy crops and residues, and evaluate biomass cascades involving AD technolo

  6. How biomass composition determines protein extractability

    NARCIS (Netherlands)

    Sari, Y.W.; Syafitri, U.; Sanders, J.P.M.; Bruins, M.E.

    2015-01-01

    Biomass consists of a complex mixture of different components, of which protein potentially has a high added value for biorefinery. In this study, protein extractability of different types of biomass, mostly by-products, was analyzed. Protein yield obtained from a three step extraction using alkali

  7. Environmental implications of increased biomass energy use

    Energy Technology Data Exchange (ETDEWEB)

    Miles, T.R. Sr.; Miles, T.R. Jr. (Miles (Thomas R.), Portland, OR (United States))

    1992-03-01

    This study reviews the environmental implications of continued and increased use of biomass for energy to determine what concerns have been and need to be addressed and to establish some guidelines for developing future resources and technologies. Although renewable biomass energy is perceived as environmentally desirable compared with fossil fuels, the environmental impact of increased biomass use needs to be identified and recognized. Industries and utilities evaluating the potential to convert biomass to heat, electricity, and transportation fuels must consider whether the resource is reliable and abundant, and whether biomass production and conversion is environmentally preferred. A broad range of studies and events in the United States were reviewed to assess the inventory of forest, agricultural, and urban biomass fuels; characterize biomass fuel types, their occurrence, and their suitability; describe regulatory and environmental effects on the availability and use of biomass for energy; and identify areas for further study. The following sections address resource, environmental, and policy needs. Several specific actions are recommended for utilities, nonutility power generators, and public agencies.

  8. Catalytic gasification of dry and wet biomass

    NARCIS (Netherlands)

    van Rossum, G.; Potic, B.; Kersten, Sascha R.A.; van Swaaij, Willibrordus Petrus Maria

    2009-01-01

    Catalytic gasification of dry biomass and of wet biomass streams in hot compressed water are reviewed and discussed as potential technologies for the production of synthesis gas, hydrogen- and methane-rich gas. Next to literature data also new experimental results from our laboratory on catalytic

  9. A tree biomass and carbon estimation system

    Science.gov (United States)

    Emily B. Schultz; Thomas G. Matney; Donald L. Grebner

    2013-01-01

    Appropriate forest management decisions for the developing woody biofuel and carbon credit markets require inventory and growth-and-yield systems reporting component tree dry weight biomass estimates. We have developed an integrated growth-and-yield and biomass/carbon calculator. The objective was to provide Mississippi’s State inventory system with bioenergy economic...

  10. Materials for Waste Incinerators and Biomass Plants

    DEFF Research Database (Denmark)

    Rademakers, P.; Grossmann, G.; Karlsson, A.

    1998-01-01

    This paper reviews the projects of the sub-package on waste incineration and biomass firing carried out within COST 501 Round III, Work Package 13.......This paper reviews the projects of the sub-package on waste incineration and biomass firing carried out within COST 501 Round III, Work Package 13....

  11. The relative cost of biomass energy transport.

    Science.gov (United States)

    Searcy, Erin; Flynn, Peter; Ghafoori, Emad; Kumar, Amit

    2007-04-01

    Logistics cost, the cost of moving feedstock or products, is a key component of the overall cost of recovering energy from biomass. In this study, we calculate for small- and large-project sizes, the relative cost of transportation by truck, rail, ship, and pipeline for three biomass feedstocks, by truck and pipeline for ethanol, and by transmission line for electrical power. Distance fixed costs (loading and unloading) and distance variable costs (transport, including power losses during transmission), are calculated for each biomass type and mode of transportation. Costs are normalized to a common basis of a giga Joules of biomass. The relative cost of moving products vs feedstock is an approximate measure of the incentive for location of biomass processing at the source of biomass, rather than at the point of ultimate consumption of produced energy. In general, the cost of transporting biomass is more than the cost of transporting its energy products. The gap in cost for transporting biomass vs power is significantly higher than the incremental cost of building and operating a power plant remote from a transmission grid. The cost of power transmission and ethanol transport by pipeline is highly dependent on scale of project. Transport of ethanol by truck has a lower cost than by pipeline up to capacities of 1800 t/d. The high cost of transshipment to a ship precludes shipping from being an economical mode of transport for distances less than 800 km (woodchips) and 1500 km (baled agricultural residues).

  12. Manufacture of Prebiotics from Biomass Sources

    Science.gov (United States)

    Gullón, Patricia; Gullón, Beatriz; Moure, Andrés; Alonso, José Luis; Domínguez, Herminia; Parajó, Juan Carlos

    Biomass from plant material is the most abundant and widespread renewable raw material for sustainable development, and can be employed as a source of polymeric and oligomeric carbohydrates. When ingested as a part of the diet, some biomass polysaccharides and/or their oligomeric hydrolysis products are selectively fermented in the colon, causing prebiotic effects.

  13. Biomass electrochemistry : from cellulose to sorbitol

    NARCIS (Netherlands)

    Kwon, Youngkook

    2013-01-01

    The primary goal of this thesis is to study the potential role of electrochemistry in finding new routes for sustainable chemicals from biomass in aqueous-phase solutions. In order to assess the potential of electrochemistry in biomass conversion, we developed an online HPLC system by using a fracti

  14. Biomass resilience of Neotropical secondary forests.

    Science.gov (United States)

    Poorter, Lourens; Bongers, Frans; Aide, T Mitchell; Almeyda Zambrano, Angélica M; Balvanera, Patricia; Becknell, Justin M; Boukili, Vanessa; Brancalion, Pedro H S; Broadbent, Eben N; Chazdon, Robin L; Craven, Dylan; de Almeida-Cortez, Jarcilene S; Cabral, George A L; de Jong, Ben H J; Denslow, Julie S; Dent, Daisy H; DeWalt, Saara J; Dupuy, Juan M; Durán, Sandra M; Espírito-Santo, Mario M; Fandino, María C; César, Ricardo G; Hall, Jefferson S; Hernandez-Stefanoni, José Luis; Jakovac, Catarina C; Junqueira, André B; Kennard, Deborah; Letcher, Susan G; Licona, Juan-Carlos; Lohbeck, Madelon; Marín-Spiotta, Erika; Martínez-Ramos, Miguel; Massoca, Paulo; Meave, Jorge A; Mesquita, Rita; Mora, Francisco; Muñoz, Rodrigo; Muscarella, Robert; Nunes, Yule R F; Ochoa-Gaona, Susana; de Oliveira, Alexandre A; Orihuela-Belmonte, Edith; Peña-Claros, Marielos; Pérez-García, Eduardo A; Piotto, Daniel; Powers, Jennifer S; Rodríguez-Velázquez, Jorge; Romero-Pérez, I Eunice; Ruíz, Jorge; Saldarriaga, Juan G; Sanchez-Azofeifa, Arturo; Schwartz, Naomi B; Steininger, Marc K; Swenson, Nathan G; Toledo, Marisol; Uriarte, Maria; van Breugel, Michiel; van der Wal, Hans; Veloso, Maria D M; Vester, Hans F M; Vicentini, Alberto; Vieira, Ima C G; Bentos, Tony Vizcarra; Williamson, G Bruce; Rozendaal, Danaë M A

    2016-02-11

    Land-use change occurs nowhere more rapidly than in the tropics, where the imbalance between deforestation and forest regrowth has large consequences for the global carbon cycle. However, considerable uncertainty remains about the rate of biomass recovery in secondary forests, and how these rates are influenced by climate, landscape, and prior land use. Here we analyse aboveground biomass recovery during secondary succession in 45 forest sites and about 1,500 forest plots covering the major environmental gradients in the Neotropics. The studied secondary forests are highly productive and resilient. Aboveground biomass recovery after 20 years was on average 122 megagrams per hectare (Mg ha(-1)), corresponding to a net carbon uptake of 3.05 Mg C ha(-1) yr(-1), 11 times the uptake rate of old-growth forests. Aboveground biomass stocks took a median time of 66 years to recover to 90% of old-growth values. Aboveground biomass recovery after 20 years varied 11.3-fold (from 20 to 225 Mg ha(-1)) across sites, and this recovery increased with water availability (higher local rainfall and lower climatic water deficit). We present a biomass recovery map of Latin America, which illustrates geographical and climatic variation in carbon sequestration potential during forest regrowth. The map will support policies to minimize forest loss in areas where biomass resilience is naturally low (such as seasonally dry forest regions) and promote forest regeneration and restoration in humid tropical lowland areas with high biomass resilience.

  15. Synthetic and Biomass Alternate Fueling in Aviation

    Science.gov (United States)

    Hendricks, Robert C.; Bushnell, Dennis M.

    2009-01-01

    Must use earth's most abundant natural resources - Biomass, Solar, Arid land (43%), Seawater (97%) with nutrients (80%) plus brackish waters and nutrients resolve environmental triangle of conflicts energy-food-freshwater and ultrafine particulate hazards. Requires Paradigm Shift - Develop and Use Solar* for energy; Biomass for aviation and hybrid-electric-compressed air mobility fueling with transition to hydrogen long term.

  16. Lessons learned from existing biomass power plants

    Energy Technology Data Exchange (ETDEWEB)

    Wiltsee, G.

    2000-02-24

    This report includes summary information on 20 biomass power plants, which represent some of the leaders in the industry. In each category an effort is made to identify plants that illustrate particular points. The project experiences described capture some important lessons learned that lead in the direction of an improved biomass power industry.

  17. Electricity and heat production by biomass cogeneration

    Science.gov (United States)

    Marčič, Simon; Marčič, Milan

    2017-07-01

    In Slovenia, approximately 2 % of electricity is generated using cogeneration systems. Industrial and district heating networks ensure the growth of such technology. Today, many existing systems are outdated, providing myriad opportunities for reconstruction. One concept for the development of households and industry envisages the construction of several small biomass units and the application of natural gas as a fuel with a relatively extensive distribution network. This concept has good development potential in Slovenia. Forests cover 56 % of the surface area in Slovenia, which has, as a result, a lot of waste wood to be turned into biomass. Biomass is an important fuel in Slovenia. Biomass is gasified in a gasifier, and the wood gas obtained is used to power the gas engine. This paper describes a biomass cogeneration system as the first of this type in Slovenia, located in Ruše.

  18. Sustainable Biomass Resources for Biogas Production

    DEFF Research Database (Denmark)

    Meyer, Ane Katharina Paarup

    such biomasses in the biogas sector. Sustainability in the use of biomass feedstock for energy production is of key importance for a stable future food and energy supply, and for the functionality of the Earths ecosystems. A range of biomass resources were assessed in respect to sustainability, availability......, and energetic feasibility by combining the use of a geographical information system with laboratory experiments, statistical analyses, field studies, and literature reviews. The biomasses identified as sustainable in this study were animal manure, straw, surplus grass from agricultural production, grass from...... nature conservation, and grass from roadside verges. It was found that a significant potential of the investigated sustainable biomass resources are available in Denmark, but also on European level. In Europe, the energy potential in 2030 from animal manure, straw and surplus grass was projected to range...

  19. Forest Biomass for Climate Change Mitigation

    DEFF Research Database (Denmark)

    Nielsen, Anders Tærø

    Awareness of elevated CO2 levels in the atmosphere and resulting climate change has increased focus on renewable energy sources during recent decades. Biomass for energy has been predicted to have the greatest potential for CO2 reductions in the short term and the IPCC assumes that the use...... of biomass for energy is CO2 neutral. Several studies have however criticized this CO2 neutrality assumption and questioned whether CO2 reductions actually are achieved through use of biomass for energy. The purpose of this thesis is to investigate the biomass production potential of poplar plantations...... on southern Scandinavian sites, managed under different systems both in agriculture and in forests. In addition, the objective is to assess the potential of the poplar plantations to mitigate climate change by using poplar biomass for substitution of fossil fuels in comparison to a traditional product...

  20. [Individual biomass of natural Pinus densiflora].

    Science.gov (United States)

    Wang, C; Jin, Y; Jin, C; Liu, J; Jin, Y

    2000-02-01

    The aboveground biomass of individuals with different growth potentials in natural Pinus densiflora forest with different stand densities was measured in Yanbian, Jilin Province. The variation of individual biomass affected by densities was in order of dominant tree branch > needle > bark. The biomass components of P. densifliora with different growth potentials varied markedly with the approaching of density class III, and the change of intermediate trees was similar to the whole stand. The vertical distributions of biomass of different trees were different from each other, but all showed that the biomass of trunks and barks was mainly distributed below 6 m high from ground, that of branches was within 6-10 m high, that of needles was uniform in the upper, middle and lower layers, and that of branches and needles in upper layer was least affected by density.

  1. Assessment of Biomass Resources in Liberia

    Energy Technology Data Exchange (ETDEWEB)

    Milbrandt, A.

    2009-04-01

    Biomass resources meet about 99.5% of the Liberian population?s energy needs so they are vital to basic welfare and economic activity. Already, traditional biomass products like firewood and charcoal are the primary energy source used for domestic cooking and heating. However, other more efficient biomass technologies are available that could open opportunities for agriculture and rural development, and provide other socio-economic and environmental benefits.The main objective of this study is to estimate the biomass resources currently and potentially available in the country and evaluate their contribution for power generation and the production of transportation fuels. It intends to inform policy makers and industry developers of the biomass resource availability in Liberia, identify areas with high potential, and serve as a base for further, more detailed site-specific assessments.

  2. Biomass: old fuel for modern times

    Energy Technology Data Exchange (ETDEWEB)

    Domac, J. [IEA Bioenergy Task 29, Zagreb (Croatia); Richards, K. [TV Energy Ltd., (United Kingdom); IEA Bioenergy Task 29, Zagreb (Croatia); Segon, V. [Energy Institute Hrvoje Pozar, Zagreb (Croatia)

    2005-08-01

    The article extols the virtues of biomass in terms of environmental benefits, job creation, economics and sustainable development. At present, biomass is the biggest single renewable energy source worldwide and its use amounts to about 1 billion tonnes of oil equivalent. The various routes for deriving bioenergy from biomass are mentioned. Bioenergy is said to have the potential to supply 50% of the world's energy demand during the next century, but so far, in the UK at least, the bioenergy/wood fuel market has not materialised. The barriers and challenges which need to be overcome for the further exploitation of biomass are listed. Biomass has a bright future and should no longer be regarded as the 'poor man's fuel'.

  3. Freshwater aquatic plant biomass production in Florida

    Energy Technology Data Exchange (ETDEWEB)

    Reddy, K.R.; Sutton, D.L.; Bowes, G.

    1983-01-01

    About 8% (1.2 million ha) of the total surface area of Florida is occupied by freshwater. Many of these water bodies are eutrophic. Nutrients present in these water bodies can be potentially used to culture aquatic plants as a possible feedstock for methane production. This paper summarizes the results of known research findings on biomass production potential of freshwater aquatic plants in Florida and identifies key research needs to improve the quality and quantity of biomass yields. Among floating aquatic plants, biomass yield potential was in the order of water-hyacinth > water lettuce > pennywort > salvinia > duckweed > azolla. Pennywort, duckweed, and azolla appear to perform well during the cooler months compared to other aquatic plants. Among emergent plants, biomass yield potential was in the order of southern wild rice > cattails > soft rush > bulrush. Cultural techniques, nutrient management, and environmental factors influencing the biomass yields were discussed. 68 references.

  4. Water vapor release from biomass combustion

    Science.gov (United States)

    Parmar, R. S.; Welling, M.; Andreae, M. O.; Helas, G.

    2008-10-01

    We report on the emission of water vapor from biomass combustion. Concurrent measurements of carbon monoxide and carbon dioxide are used to scale the concentrations of water vapor found, and are referenced to carbon in the biomass. The investigated fuel types include hardwood (oak and African musasa), softwood (pine and spruce, partly with green needles), and African savanna grass. The session-averaged ratio of H2O to the sum of CO and CO2 in the emissions from 16 combustion experiments ranged from 1.2 to 3.7, indicating the presence of water that is not chemically bound. This non-bound biomass moisture content ranged from 33% in the dry African hardwood, musasa, to 220% in fresh pine branches with needles. The moisture content from fresh biomass contributes significantly to the water vapor in biomass burning emissions, and its influence on the behavior of fire plumes and pyro-cumulus clouds needs to be evaluated.

  5. Production of methanol/DME from biomass

    DEFF Research Database (Denmark)

    Ahrenfeldt, Jesper; Henriksen, Ulrik Birk; Münster-Swendsen, Janus

    In this project the production of DME/methanol from biomass has been investigated. Production of DME/methanol from biomass requires the use of a gasifier to transform the solid fuel to a synthesis gas (syngas) - this syngas can then be catalytically converted to DME/methanol. Two different gasifier...... cleaning. This was proved by experiments. Thermodynamic computer models of DME and methanol plants based on using the Two-Stage Gasification concept were created to show the potential of such plants. The models showed that the potential biomass to DME/methanol + net electricity energy efficiency was 51...... gasification, but little information exists on using these types of gasifiers for biomass gasification. The experiments performed provided quantitative data on product and gas composition as a function of operation conditions. Biomass can be gasified with less oxygen consumption compared to coal. The organic...

  6. IMPROVING BIOMASS LOGISTICS COST WITHIN AGRONOMIC SUSTAINABILITY CONSTRAINTS AND BIOMASS QUALITY TARGETS

    Energy Technology Data Exchange (ETDEWEB)

    J. Richard Hess; Kevin L. Kenney; Christopher T. Wright; David J. Muth; William Smith

    2012-10-01

    Equipment manufacturers have made rapid improvements in biomass harvesting and handling equipment. These improvements have increased transportation and handling efficiencies due to higher biomass densities and reduced losses. Improvements in grinder efficiencies and capacity have reduced biomass grinding costs. Biomass collection efficiencies (the ratio of biomass collected to the amount available in the field) as high as 75% for crop residues and greater than 90% for perennial energy crops have also been demonstrated. However, as collection rates increase, the fraction of entrained soil in the biomass increases, and high biomass residue removal rates can violate agronomic sustainability limits. Advancements in quantifying multi-factor sustainability limits to increase removal rate as guided by sustainable residue removal plans, and mitigating soil contamination through targeted removal rates based on soil type and residue type/fraction is allowing the use of new high efficiency harvesting equipment and methods. As another consideration, single pass harvesting and other technologies that improve harvesting costs cause biomass storage moisture management challenges, which challenges are further perturbed by annual variability in biomass moisture content. Monitoring, sampling, simulation, and analysis provide basis for moisture, time, and quality relationships in storage, which has allowed the development of moisture tolerant storage systems and best management processes that combine moisture content and time to accommodate baled storage of wet material based upon “shelf-life.” The key to improving biomass supply logistics costs has been developing the associated agronomic sustainability and biomass quality technologies and processes that allow the implementation of equipment engineering solutions.

  7. Driftless Area Initiative Biomass Energy Project

    Energy Technology Data Exchange (ETDEWEB)

    Wright, Angie [Northeast Iowa Resource Conservation & Development, Inc., Postville, IA (United States); Bertjens, Steve [Natural Resources Conservation Service, Madison, WI (United States); Lieurance, Mike [Northeast Iowa Resource Conservation & Development, Inc., Postville, IA (United States); Berguson, Bill [Univ. of Minnesota, Minneapolis, MN (United States). Natural Resources Research Inst.; Buchman, Dan [Univ. of Minnesota, Minneapolis, MN (United States). Natural Resources Research Inst.

    2012-12-31

    The Driftless Area Initiative Biomass Energy Project evaluated the potential for biomass energy production and utilization throughout the Driftless Region of Illinois, Iowa, Minnesota and Wisconsin. The research and demonstration aspect of the project specifically focused on biomass energy feedstock availability and production potential in the region, as well as utilization potential of biomass feedstocks for heat, electrical energy production, or combined heat and power operations. The Driftless Region was evaluated because the topography of the area offers more acres of marginal soils on steep slopes, wooded areas, and riparian corridors than the surrounding “Corn Belt”. These regional land characteristics were identified as potentially providing opportunity for biomass feedstock production that could compete with traditional agriculture commodity crops economically. The project researched establishment methods and costs for growing switchgrass on marginal agricultural lands to determine the economic and quantitative feasibility of switchgrass production for biomass energy purposes. The project was successful in identifying the best management and establishment practices for switchgrass in the Driftless Area, but also demonstrated that simple economic payback versus commodity crops could not be achieved at the time of the research. The project also analyzed the availability of woody biomass and production potential for growing woody biomass for large scale biomass energy production in the Driftless Area. Analysis determined that significant resources exist, but costs to harvest and deliver to the site were roughly 60% greater than that of natural gas at the time of the study. The project contributed significantly to identifying both production potential of biomass energy crops and existing feedstock availability in the Driftless Area. The project also analyzed the economic feasibility of dedicated energy crops in the Driftless Area. High commodity crop prices

  8. Driftless Area Initiative Biomass Energy Project

    Energy Technology Data Exchange (ETDEWEB)

    Bertjens, Steve; Wright, Angie; Lieurance, Mike; berguson, bill; Buchman, Dan

    2012-12-31

    The Driftless Area Initiative Biomass Energy Project evaluated the potential for biomass energy production and utilization throughout the Driftless Region of Illinois, Iowa, Minnesota and Wisconsin. The research and demonstration aspect of the project specifically focused on biomass energy feedstock availability and production potential in the region, as well as utilization potential of biomass feedstocks for heat, electrical energy production, or combined heat and power operations. The Driftless Region was evaluated because the topography of the area offers more acres of marginal soils on steep slopes, wooded areas, and riparian corridors than the surrounding “Corn Belt”. These regional land characteristics were identified as potentially providing opportunity for biomass feedstock production that could compete with traditional agriculture commodity crops economically. The project researched establishment methods and costs for growing switchgrass on marginal agricultural lands to determine the economic and quantitative feasibility of switchgrass production for biomass energy purposes. The project was successful in identifying the best management and establishment practices for switchgrass in the Driftless Area, but also demonstrated that simple economic payback versus commodity crops could not be achieved at the time of the research. The project also analyzed the availability of woody biomass and production potential for growing woody biomass for large scale biomass energy production in the Driftless Area. Analysis determined that significant resources exist, but costs to harvest and deliver to the site were roughly 60% than that of natural gas at the time of the study. The project contributed significantly to identifying both production potential of biomass energy crops and existing feedstock availability in the Driftless Area. The project also analyzed the economic feasibility of dedicated energy crops in the Driftless Area. High commodity crop prices and

  9. Allometric models for estimating biomass and carbon in Alnus acuminata

    National Research Council Canada - National Science Library

    William Fonseca; Laura Ruíz; Marylin Rojas; Federico Allice

    2013-01-01

    ... (leaves, branches, stem and root) and total tree biomass in Alnus acuminata (Kunth) in Costa Rica. Additionally, models were developed to estimate biomass and carbon in trees per hectare and for total plant biomass per hectare...

  10. 78 FR 46331 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2013-07-31

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Biomass... for candidates to fill vacancies on the Biomass Research and Development Technical Advisory Committee...: http://biomassboard.gov/committee/committee.html . SUPPLEMENTARY INFORMATION: The Biomass Research...

  11. Absolute Quantification of Individual Biomass Concentrations in a Methanogenic Coculture

    NARCIS (Netherlands)

    Junicke, H.; Abbas, B.; Oentoro, J.; Van Loosdrecht, M.; Kleerebezem, R.

    2014-01-01

    Identification of individual biomass concentrations is a crucial step towards an improved understanding of anaerobic digestion processes and mixed microbial conversions in general. The knowledge of individual biomass concentrations allows for the calculation of biomass specific conversion rates whic

  12. Absolute Quantification of Individual Biomass Concentrations in a Methanogenic Coculture

    NARCIS (Netherlands)

    Junicke, H.; Abbas, B.; Oentoro, J.; Van Loosdrecht, M.; Kleerebezem, R.

    2014-01-01

    Identification of individual biomass concentrations is a crucial step towards an improved understanding of anaerobic digestion processes and mixed microbial conversions in general. The knowledge of individual biomass concentrations allows for the calculation of biomass specific conversion rates

  13. Simulation of Biomass Accumulation Pattern in Vapor-Phase Biofilters.

    Science.gov (United States)

    Xi, Jin-Ying; Hu, Hong-Ying; Zhang, Xian

    2012-06-01

    Existence of inert biomass and its impact on biomass accumulation patterns and biofilter performance were investigated. Four biofilters were set up in parallel to treat gaseous toluene. Each biofilter operated under different inlet toluene loadings for 100 days. Two microbial growth models, one with an inert biomass assumption and the other without, were established and compared. Results from the model with the inert biomass assumption showed better agreement with the experimental data than those based on the model without the inert biomass assumption thus verifying that inert biomass accumulation cannot be ignored in the long-term operation of biofilters. According to the model with an inert biomass assumption, the ratio of active biomass to total biomass will decrease and the inert biomass will become dominant in total biomass after a period of time. Filter bed structure simulation results showed that the void fraction is more sensitive to biomass accumulation than the specific surface area. The final void fraction of the biofilters with the highest inlet toluene loading is only 67% of its initial level while the final specific surface area is 82%. Identification and quantification of inert biomass will give a better understanding of biomass accumulation in biofilters and will result in a more exact simulation of biomass change during long-term operations. Results also indicate that an ideal biomass control technique should be able to remove most inert biomass while simultaneously preserving as much active biomass as possible.

  14. 76 FR 77963 - Oglethorpe Power Corporation; Proposed Biomass Power Plant

    Science.gov (United States)

    2011-12-15

    ...; ] DEPARTMENT OF AGRICULTURE Rural Utilities Service Oglethorpe Power Corporation; Proposed Biomass Power Plant... (Oglethorpe) for the construction of a 100 megawatt (MW) biomass plant and related facilities (Proposal)...

  15. Simulation of Biomass Accumulation Pattern in Vapor-Phase Biofilters

    Science.gov (United States)

    Xi, Jin-Ying; Hu, Hong-Ying; Zhang, Xian

    2012-01-01

    Abstract Existence of inert biomass and its impact on biomass accumulation patterns and biofilter performance were investigated. Four biofilters were set up in parallel to treat gaseous toluene. Each biofilter operated under different inlet toluene loadings for 100 days. Two microbial growth models, one with an inert biomass assumption and the other without, were established and compared. Results from the model with the inert biomass assumption showed better agreement with the experimental data than those based on the model without the inert biomass assumption thus verifying that inert biomass accumulation cannot be ignored in the long-term operation of biofilters. According to the model with an inert biomass assumption, the ratio of active biomass to total biomass will decrease and the inert biomass will become dominant in total biomass after a period of time. Filter bed structure simulation results showed that the void fraction is more sensitive to biomass accumulation than the specific surface area. The final void fraction of the biofilters with the highest inlet toluene loading is only 67% of its initial level while the final specific surface area is 82%. Identification and quantification of inert biomass will give a better understanding of biomass accumulation in biofilters and will result in a more exact simulation of biomass change during long-term operations. Results also indicate that an ideal biomass control technique should be able to remove most inert biomass while simultaneously preserving as much active biomass as possible. PMID:22693411

  16. Forest biomass observation: current state and prospective

    Directory of Open Access Journals (Sweden)

    D. G. Schepaschenko

    2017-08-01

    Full Text Available With this article, we provide an overview of the methods, instruments and initiatives for forest biomass observation at global scale. We focus on the freely available information, provided by both remote and in-situ observations. The advantages and limitation of various space borne methods, including optical, radar (C, L and P band and LiDAR, as well as respective instruments available on the orbit (MODIS, Proba-V, Landsat, Sentinel-1, Sentinel-2 , ALOS PALSAR, Envisat ASAR or expecting (BIOMASS, GEDI, NISAR, SAOCOM-CS are discussed. We emphasize the role of in-situ methods in the development of a biomass models, providing calibration and validation of remote sensing data. We focus on freely available forest biomass maps, databases and empirical models. We describe the functionality of Biomass.Geo-Wiki.org portal, which provides access to a collection of global and regional biomass maps in full resolution with unified legend and units overplayed with high-resolution imagery. The Forest-Observation-System.net is announced as an international cooperation to establish a global in-situ forest biomass database to support earth observation and to encourage investment in relevant field-based observations and science. Prospects of unmanned aerial vehicles in the forest inventory are briefly discussed. The work was partly supported by ESA IFBN project (contract 4000114425/15/NL/FF/gp.

  17. Preprocessing Moist Lignocellulosic Biomass for Biorefinery Feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Neal Yancey; Christopher T. Wright; Craig Conner; J. Richard Hess

    2009-06-01

    Biomass preprocessing is one of the primary operations in the feedstock assembly system of a lignocellulosic biorefinery. Preprocessing is generally accomplished using industrial grinders to format biomass materials into a suitable biorefinery feedstock for conversion to ethanol and other bioproducts. Many factors affect machine efficiency and the physical characteristics of preprocessed biomass. For example, moisture content of the biomass as received from the point of production has a significant impact on overall system efficiency and can significantly affect the characteristics (particle size distribution, flowability, storability, etc.) of the size-reduced biomass. Many different grinder configurations are available on the market, each with advantages under specific conditions. Ultimately, the capacity and/or efficiency of the grinding process can be enhanced by selecting the grinder configuration that optimizes grinder performance based on moisture content and screen size. This paper discusses the relationships of biomass moisture with respect to preprocessing system performance and product physical characteristics and compares data obtained on corn stover, switchgrass, and wheat straw as model feedstocks during Vermeer HG 200 grinder testing. During the tests, grinder screen configuration and biomass moisture content were varied and tested to provide a better understanding of their relative impact on machine performance and the resulting feedstock physical characteristics and uniformity relative to each crop tested.

  18. Electricity from biomass: A development strategy

    Science.gov (United States)

    1992-04-01

    The purpose of this document is to review the current status of biomass power technology and to evaluate the future directions for development that could significantly enhance the contribution of biomass power to U.S. production of electricity. This document reviews the basic principles of biomass electric systems, the previous contributions of industry and the National Biomass Energy Programs to technology development, and the options for future technology development. It discusses the market for biomass electric technology and future needs for electric power production to help establish a market-oriented development strategy. It projects trends in the performance and cost of the technology and examines the changing dynamics of the power generation market place to evaluate specific opportunities for biomass power development. In a separate document, the Biomass Power Program Five Year R&D Plan, the details of schedules, funding, and roles of participating R&D organizations within the R&D program funded by the U.S. Department of Energy (DOE) are presented. In evaluating the future directions for research and development, two cases are examined.

  19. Preprocessing Moist Lignocellulosic Biomass for Biorefinery Feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Neal Yancey; Christopher T. Wright; Craig Conner; J. Richard Hess

    2009-06-01

    Biomass preprocessing is one of the primary operations in the feedstock assembly system of a lignocellulosic biorefinery. Preprocessing is generally accomplished using industrial grinders to format biomass materials into a suitable biorefinery feedstock for conversion to ethanol and other bioproducts. Many factors affect machine efficiency and the physical characteristics of preprocessed biomass. For example, moisture content of the biomass as received from the point of production has a significant impact on overall system efficiency and can significantly affect the characteristics (particle size distribution, flowability, storability, etc.) of the size-reduced biomass. Many different grinder configurations are available on the market, each with advantages under specific conditions. Ultimately, the capacity and/or efficiency of the grinding process can be enhanced by selecting the grinder configuration that optimizes grinder performance based on moisture content and screen size. This paper discusses the relationships of biomass moisture with respect to preprocessing system performance and product physical characteristics and compares data obtained on corn stover, switchgrass, and wheat straw as model feedstocks during Vermeer HG 200 grinder testing. During the tests, grinder screen configuration and biomass moisture content were varied and tested to provide a better understanding of their relative impact on machine performance and the resulting feedstock physical characteristics and uniformity relative to each crop tested.

  20. The regional environmental impact of biomass production

    Energy Technology Data Exchange (ETDEWEB)

    Graham, R.L.

    1994-09-01

    The objective of this paper is to present a broad overview of the potential environmental impacts of biomass energy from energy crops. The subject is complex because the environmental impact of using biomass for energy must be considered in the context of alternative energy options while the environmental impact of producing biomass from energy crops must be considered in the context of the alternative land-uses. Using biomass-derived energy can reduce greenhouse gas emissions or increase them; growing biomass energy crops can enhance soil fertility or degrade it. Without knowing the context of the biomass energy, one can say little about its specific environmental impacts. The primary focus of this paper is an evaluation of the environmental impacts of growing energy crops. I present an approach for quantitatively evaluating the potential environmental impact of growing energy crops at a regional scale that accounts for the environmental and economic context of the crops. However, to set the stage for this discussion, I begin by comparing the environmental advantages and disadvantages of biomass-derived energy relative to other energy alternatives such as coal, hydropower, nuclear power, oil/gasoline, natural gas and photovoltaics.

  1. Development of Solar Biomass Drying System

    Directory of Open Access Journals (Sweden)

    Atnaw Samson Mekbib

    2017-01-01

    Full Text Available The purpose of this paper focuses on the experimental pre-treatment of biomass in agricultural site using solar energy as power source and contribution of common use and efficiency solar dryer system for consumer. The main purpose of this design for solar cabinet dryer is to dry biomass via direct and indirect heating. Direct heating is the simplest method to dry biomass by exposing the biomass under direct sunlight. The solar cabinet dryer traps solar heat to increase the temperature of the drying chamber. The biomass absorbs the heat and transforms the moisture content within the biomass into water vapour and then leaves the chamber via the exhaust air outlet. This problem however can be solved by adopting indirect solar drying system. High and controllable temperatures can be achieved as a fan is used to move the air through the solar collector. This project has successfully created a solar cabinet dryer that combines both direct and indirect solar drying systems and functions to dry biomass as well as crops effectively and efficiently with minimal maintenance. Hence, it is indeed a substitution for conventional dryers which are affordable to local farmers.

  2. Difficulties of biomass estimation over natural grassland

    Science.gov (United States)

    Kertész, Péter; Gecse, Bernadett; Pintér, Krisztina; Fóti, Szilvia; Nagy, Zoltán

    2017-04-01

    Estimation of biomass amount in grasslands using remote sensing is a challenge due to the high diversity and different phenologies of the constituting plant species. The aim of this study was to estimate the biomass amount (dry weight per area) during the vegetation period of a diverse semi-natural grassland with remote sensing. A multispectral camera (Tetracam Mini-MCA 6) was used with 3 cm ground resolution. The pre-processing method includes noise reduction, the correction for the vignetting effect and the calculation of the reflectance using an Incident Light Sensor (ILS). Calibration was made with ASD spectrophotometer as reference. To estimate biomass Partial Least Squares Regression (PLSR) statistical method was used with 5 bands and NDVI as input variables. Above ground biomass was cut in 15 quadrats (50×50 cm) as reference. The best prediction was attained in spring (r2=0.94, RMSE: 26.37 g m-2). The average biomass amount was 167 g m-2. The variability of the biomass is mainly determined by the relief, which causes the high and low biomass patches to be stable. The reliability of biomass estimation was negatively affected by the appearance of flowers and by the senescent plant parts during the summer. To determine the effects of flower's presence on the biomass estimation, 20 dominant species with visually dominant flowers in the area were selected and cover of flowers (%) were estimated in permanent plots during measurement campaigns. If the cover of flowers was low (0,9), while at higher cover of flowers (>30%), the estimation failed (r2 <0,2). This effect restricts the usage of the remote sensing method to the spring - early summer period in diverse grasslands.

  3. EERC Center for Biomass Utilization 2005

    Energy Technology Data Exchange (ETDEWEB)

    Zygarlicke, C J; Schmidt, D D; Olson, E S; Leroux, K M; Wocken, C A; Aulich, T A; WIlliams, K D

    2008-07-28

    Biomass utilization is one solution to our nation’s addiction to oil and fossil fuels. What is needed now is applied fundamental research that will cause economic technology development for the utilization of the diverse biomass resources in the United States. This Energy & Environmental Research Center (EERC) applied fundamental research project contributes to the development of economical biomass utilization for energy, transportation fuels, and marketable chemicals using biorefinery methods that include thermochemical and fermentation processes. The fundamental and basic applied research supports the broad scientific objectives of the U.S. Department of Energy (DOE) Biomass Program, especially in the area of developing alternative renewable biofuels, sustainable bioenergy, technologies that reduce greenhouse gas emissions, and environmental remediation. Its deliverables include 1) identifying and understanding environmental consequences of energy production from biomass, including the impacts on greenhouse gas production, carbon emission abatement, and utilization of waste biomass residues and 2) developing biology-based solutions that address DOE and national needs related to waste cleanup, hydrogen production from renewable biomass, biological and chemical processes for energy and fuel production, and environmental stewardship. This project serves the public purpose of encouraging good environmental stewardship by developing biomass-refining technologies that can dramatically increase domestic energy production to counter current trends of rising dependence upon petroleum imports. Decreasing the nation’s reliance on foreign oil and energy will enhance national security, the economy of rural communities, and future competitiveness. Although renewable energy has many forms, such as wind and solar, biomass is the only renewable energy source that can be governed through agricultural methods and that has an energy density that can realistically compete with

  4. Biomass use in chemical and mechanical pulping with biomass-based energy supply

    Energy Technology Data Exchange (ETDEWEB)

    Holmberg, Jonas M.; Gustavsson, Leif [Department of Engineering Physics and Mathematics, Mid Sweden University, SE-831 25 Oestersund (Sweden)

    2007-12-15

    The pulp and paper industry is energy intensive and consumes large amounts of wood. Biomass is a limited resource and its efficient use is therefore important. In this study, the total amount of biomass used for pulp and for energy is estimated for the production of several woodfree (containing only chemical pulp) and mechanical (containing mechanical pulp) printing paper products, under Swedish conditions. Chemical pulp mills today are largely self-sufficient in energy while mechanical pulp mills depend on large amounts of external electricity. Technically, all energy used in pulp- and papermaking can be biomass based. Here, we assume that all energy used, including external electricity and motor fuels, is based on forest biomass. The whole cradle-to-gate chain is included in the analyses. The results indicate that the total amount of biomass required per tonne paper is slightly lower for woodfree than for mechanical paper. For the biomass use per paper area, the paper grammage is decisive. If the grammage can be lowered by increasing the proportion of mechanical pulp, this may lower the biomass use per paper area, despite the higher biomass use per unit mass in mechanical paper. In the production of woodfree paper, energy recovery from residues in the mill accounts for most of the biomass use, while external electricity production accounts for the largest part for mechanical paper. Motor fuel production accounts for 5-7% of the biomass use. The biomass contained in the final paper product is 21-42% of the total biomass use, indicating that waste paper recovery is important. The biomass use was found to be about 15-17% lower for modelled, modern mills compared with mills representative of today's average technology. (author)

  5. Engineering verification of the biomass production chamber

    Science.gov (United States)

    Prince, R. P.; Knott, W. M., III; Sager, J. C.; Jones, J. D.

    1992-01-01

    The requirements for life support systems, both biological and physical-chemical, for long-term human attended space missions are under serious study throughout NASA. The KSC 'breadboard' project has focused on biomass production using higher plants for atmospheric regeneration and food production in a special biomass production chamber. This chamber is designed to provide information on food crop growth rate, contaminants in the chamber that alter plant growth requirements for atmospheric regeneration, carbon dioxide consumption, oxygen production, and water utilization. The shape and size, mass, and energy requirements in relation to the overall integrity of the biomass production chamber are under constant study.

  6. Biomass Indirect Liquefaction Strategy Workshop Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2014-07-01

    This report is based on the proceedings of the U.S. Department of Energy Bioenergy Technologies Office Biomass Indirect Liquefaction Strategy Workshop. The workshop, held March 20–21, 2014, in Golden, Colorado, discussed and detailed the research and development needs for biomass indirect liquefaction. Discussions focused on pathways that convert biomass-based syngas (or any carbon monoxide, hydrogen gaseous stream) to liquid intermediates (alcohols or acids) and further synthesize those intermediates to liquid hydrocarbons that are compatible as either a refinery feed or neat fuel.

  7. Temperature Modelling of the Biomass Pretreatment Process

    DEFF Research Database (Denmark)

    2012-01-01

    In a second generation biorefinery, the biomass pretreatment stage has an important contribution to the efficiency of the downstream processing units involved in biofuel production. Most of the pretreatment process occurs in a large pressurized thermal reactor that presents an irregular temperature...... distribution. Therefore, an accurate temperature model is critical for observing the biomass pretreatment. More than that, the biomass is also pushed with a constant horizontal speed along the reactor in order to ensure a continuous throughput. The goal of this paper is to derive a temperature model...

  8. BIOMASS REBURNING - MODELING/ENGINEERING STUDIES

    Energy Technology Data Exchange (ETDEWEB)

    Vladimir Zamansky; Chris Lindsey; Vitali Lissianski

    2000-01-28

    This project is designed to develop engineering and modeling tools for a family of NO{sub x} control technologies utilizing biomass as a reburning fuel. During the ninth reporting period (September 27--December 31, 1999), EER prepared a paper Kinetic Model of Biomass Reburning and submitted it for publication and presentation at the 28th Symposium (International) on Combustion, University of Edinburgh, Scotland, July 30--August 4, 2000. Antares Group Inc, under contract to Niagara Mohawk Power Corporation, evaluated the economic feasibility of biomass reburning options for Dunkirk Station. A preliminary report is included in this quarterly report.

  9. [Low temperature plasma technology for biomass refinery].

    Science.gov (United States)

    Fu, Xiaoguo; Chen, Hongzhang

    2014-05-01

    Biorefinery that utilizes renewable biomass for production of fuels, chemicals and bio-materials has become more and more important in chemical industry. Recently, steam explosion technology, acid and alkali treatment are the main biorefinery treatment technologies. Meanwhile, low temperature plasma technology has attracted extensive attention in biomass refining process due to its unique chemical activity and high energy. We systemically summarize the research progress of low temperature plasma technology for pretreatment, sugar platflow, selective modification, liquefaction and gasification in biomass refinery. Moreover, the mechanism of low temperature plasma in biorefinery and its further development were also discussed.

  10. Biomass structure of exotic invasive plant Galinsona parviflora

    Institute of Scientific and Technical Information of China (English)

    Shuyan QI; Wenduo XU; Yan WEN

    2008-01-01

    Galinsona parviflora (Asteraceae) is a wide-spread annual weed that is invasive,colonizing new ground where it is able to persist.We studied the bio-mass structure of the G.Parviflora population at the module level by using the methods of field plot invest-igation and weighing at 10 sample plots.Modular bio-mass was calculated and used for analysis of relation-ships between various modules.The results show that there was a positive correlation between plant height and modular biomass,between stem biomass and root biomass,stem biomass and capitulum biomass,above-ground biomass and underground biomass,and lastly,stem biomass and leaf biomass.The preferred model which measured all the relationships was a power func-tion model with absolute coefficients(R2) ranging from 0.6303 to 0.9782.

  11. Assessment of Biomass Resources in Afghanistan

    Energy Technology Data Exchange (ETDEWEB)

    Milbrandt, A.; Overend, R.

    2011-01-01

    Afghanistan is facing many challenges on its path of reconstruction and development. Among all its pressing needs, the country would benefit from the development and implementation of an energy strategy. In addition to conventional energy sources, the Afghan government is considering alternative options such as energy derived from renewable resources (wind, solar, biomass, geothermal). Biomass energy is derived from a variety of sources -- plant-based material and residues -- and can be used in various conversion processes to yield power, heat, steam, and fuel. This study provides policymakers and industry developers with information on the biomass resource potential in Afghanistan for power/heat generation and transportation fuels production. To achieve this goal, the study estimates the current biomass resources and evaluates the potential resources that could be used for energy purposes.

  12. Butanol production from renewable biomass by clostridia.

    Science.gov (United States)

    Jang, Yu-Sin; Malaviya, Alok; Cho, Changhee; Lee, Joungmin; Lee, Sang Yup

    2012-11-01

    Global energy crisis and limited supply of petroleum fuels have rekindled the worldwide focus towards development of a sustainable technology for alternative fuel production. Utilization of abundant renewable biomass offers an excellent opportunity for the development of an economical biofuel production process at a scale sufficiently large to have an impact on sustainability and security objectives. Additionally, several environmental benefits have also been linked with the utilization of renewable biomass. Butanol is considered to be superior to ethanol due to its higher energy content and less hygroscopy. This has led to an increased research interest in butanol production from renewable biomass in recent years. In this paper, we review the various aspects of utilizing renewable biomass for clostridial butanol production. Focus is given on various alternative substrates that have been used for butanol production and on fermentation strategies recently reported to improve butanol production. Copyright © 2012 Elsevier Ltd. All rights reserved.

  13. Upgrading Fuel Properties of Biomass by Torrefaction

    DEFF Research Database (Denmark)

    Shang, Lei; Holm, Jens Kai

    Torrefaction is a mild thermal (200 – 300 ÛC) treatment in an inert atmosphere, which is known to increase the energy density of biomass by evaporating water and a proportion of volatiles. In this work, the influence of torrefaction on the chemical and mechanical properties (grindability and hygr......Torrefaction is a mild thermal (200 – 300 ÛC) treatment in an inert atmosphere, which is known to increase the energy density of biomass by evaporating water and a proportion of volatiles. In this work, the influence of torrefaction on the chemical and mechanical properties (grindability...... biomass were detected in situ by coupling mass spectrometer with a thermogravimetric analyzer (TGA). The main components were water, carbon monoxide, formic acid, formaldehyde, methanol, acetic acid, carbon dioxide, and methyl chloride. The cumulative releases of gas products from three biomass fuels...

  14. 2011 Biomass Program Platform Peer Review: Feedstock

    Energy Technology Data Exchange (ETDEWEB)

    McCann, Laura [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Feedstock Platform Review meeting.

  15. 2011 Biomass Program Platform Peer Review. Infrastructure

    Energy Technology Data Exchange (ETDEWEB)

    Lindauer, Alicia [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Infrastructure Platform Review meeting.

  16. 2011 Biomass Program Platform Peer Review: Algae

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Joyce [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Algae Platform Review meeting.

  17. Community assessment of tropical tree biomass

    DEFF Research Database (Denmark)

    Theilade, Ida; Rutishauser, Ervan; Poulsen, Michael K.

    2015-01-01

    Background REDD+ programs rely on accurate forest carbon monitoring. Several REDD+ projects have recently shown that local communities can monitor above ground biomass as well as external professionals, but at lower costs. However, the precision and accuracy of carbon monitoring conducted by local...... communities have rarely been assessed in the tropics. The aim of this study was to investigate different sources of error in tree biomass measurements conducted by community monitors and determine the effect on biomass estimates. Furthermore, we explored the potential of local ecological knowledge to assess...... measurement, with special attention given to large and odd-shaped trees. A better understanding of traditional classification systems and concepts is required for local tree identifications and wood density estimates to become useful in monitoring of biomass and tree diversity....

  18. Upgrading Fuel Properties of Biomass by Torrefaction

    DEFF Research Database (Denmark)

    Shang, Lei; Holm, Jens Kai

    biomass were detected in situ by coupling mass spectrometer with a thermogravimetric analyzer (TGA). The main components were water, carbon monoxide, formic acid, formaldehyde, methanol, acetic acid, carbon dioxide, and methyl chloride. The cumulative releases of gas products from three biomass fuels......Torrefaction is a mild thermal (200 – 300 ÛC) treatment in an inert atmosphere, which is known to increase the energy density of biomass by evaporating water and a proportion of volatiles. In this work, the influence of torrefaction on the chemical and mechanical properties (grindability...... and hygroscopicity) of wood chips, wood pellets and wheat straw was investigated and compared. The mass loss during torrefaction was found to be a useful indicator for determining the degree of torrefaction. For all three biomass, higher torrefaction temperature or longer residence time resulted in higher mass loss...

  19. Use of biomass today; Biomassenutzung heute

    Energy Technology Data Exchange (ETDEWEB)

    Schimpf, H. [Landesanstalt fuer Landwirtschaft und Gartenbau Sachsen-Anhalt/Koordinierungsstelle Nachwachsende Rohstoffe, Bernburg (Germany)

    2005-12-15

    Biomass is a much-mentioned alternative to fossil fuels today. The contribution investigates its current contribution to power supply, and the situation in the state of Sachsen-Anhalt in particular. (orig.)

  20. Puerto Rico Above Ground Biomass Map, 2000

    Data.gov (United States)

    U.S. Environmental Protection Agency — This image dataset details the U.S. Commonwealth of Puerto Rico above-ground forest biomass (AGB) (baseline 2000) developed by the United States (US) Environmental...

  1. Fast pyrolysis of biomass at high temperatures

    DEFF Research Database (Denmark)

    Trubetskaya, Anna

    This Ph.D. thesis describes experimental and modeling investigations of fast high temperature pyrolysis of biomass. Suspension firing of biomass is widely used for power generation and has been considered as an important step in reduction of greenhouse gas emissions by using less fossil fuels. Fast...... pyrolysis at high temperatures plays a significant role in the overall combustion process since the biomass type, the reaction kinetics and heat transfer rates during pyrolysis influence the volatile gas release. The solid residue yield and its properties in suspension firing, including particle size...... and shape, composition, reactivity and burnout depend significantly on the operating conditions of the fast pyrolysis. Biomass fast pyrolysis experiments were performed in a laboratory-scale wire mesh reactor and bench scale atmospheric pressure drop tube / entrained flow reactors with the aim...

  2. Sustainable Biofuels from Forests: Woody Biomass

    Directory of Open Access Journals (Sweden)

    Edwin H. White

    2011-11-01

    Full Text Available The use of woody biomass feedstocks for bioenergy and bioproducts involves multiple sources of material that together create year round supplies. The main sources of woody biomass include residues from wood manufacturing industries, low value trees including logging slash in forests that are currently underutilized and dedicated short-rotation woody crops. Conceptually a ton of woody biomass feedstocks can replace a barrel of oil as the wood is processed (refined through a biorefinery. As oil is refined only part of the barrel is used for liquid fuel, e.g., gasoline, while much of the carbon in oil is refined into higher value chemical products-carbon in woody biomass can be refined into the same value-added products.

  3. CFD Studies on Biomass Thermochemical Conversion

    Directory of Open Access Journals (Sweden)

    Lifeng Yan

    2008-06-01

    Full Text Available Thermochemical conversion of biomass offers an efficient and economically process to provide gaseous, liquid and solid fuels and prepare chemicals derived from biomass. Computational fluid dynamic (CFD modeling applications on biomass thermochemical processes help to optimize the design and operation of thermochemical reactors. Recent progression in numerical techniques and computing efficacy has advanced CFD as a widely used approach to provide efficient design solutions in industry. This paper introduces the fundamentals involved in developing a CFD solution. Mathematical equations governing the fluid flow, heat and mass transfer and chemical reactions in thermochemical systems are described and sub-models for individual processes are presented. It provides a review of various applications of CFD in the biomass thermochemical process field.

  4. Biomass allocation patterns across China's terrestrial biomes

    National Research Council Canada - National Science Library

    Wang, Limei; Li, Longhui; Chen, Xi; Tian, Xin; Wang, Xiaoke; Luo, Geping

    2014-01-01

    .... In this study, we compiled 2088 pairs of root and shoot biomass data across China's terrestrial biomes to examine variations in the RS and its responses to biotic and abiotic factors including...

  5. Understanding Ionic Liquid Pretreatment of Lignocellulosic Biomasses

    Science.gov (United States)

    Pretreatment of biomass is essential for breaking apart highly ordered and crystalline plant cell walls and loosening the lignin and hemicellulose conjugation to cellulose microfibrills, thereby facilitating enzyme accessibility and adsorption and reducing costs of downstream saccharification proces...

  6. 2011 Biomass Program Platform Peer Review. Sustainability

    Energy Technology Data Exchange (ETDEWEB)

    Eng, Alison Goss [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Sustainability Platform Review meeting.

  7. 2011 Biomass Program Platform Peer Review: Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Haq, Zia [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Analysis Platform Review meeting.

  8. TG-FTIR analysis of biomass pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Bassilakis, R.; Carangelo, R.M.; Wojtowicz, M.A. [Advanced Fuel Research Inc., Hartford, CT (United States)

    2001-10-09

    A great need exists for comprehensive biomass-pyrolysis models that could predict yields and evolution patterns of selected volatile products as a function of feedstock characteristics and process conditions. A thermogravimetric analyzer coupled with Fourier transform infrared analysis of evolving products (TG-FTIR) can provide useful input to such models in the form of kinetic information obtained under low heating rate conditions. In this work, robust TG-FTIR quantification routes were developed for infrared analysis of volatile products relevant to biomass pyrolysis. The analysis was applied to wheat straw, three types of tobacco (Burley, Oriental, and Bright) and three biomass model compounds (xylan, chlorogenic acid, and D-glucose). Product yields were compared with literature data, and species potentially quantifiable by FT-IR are reviewed. Product-evolution patterns are reported for all seven biomass samples. 41 refs., 7 figs., 2 tabs.

  9. Lactic acid fermentation-aided biomass conversion

    Energy Technology Data Exchange (ETDEWEB)

    Martin, A.M. [Memorial Univ. of Newfoundland, St. John`s, NF (Canada). Dept. of Biochemistry

    1996-09-01

    The preservation of fisheries biomass by lactic acid fermentation is discussed. This method is favourably compared to acid ensiling and fish meal production in terms of safety considerations, energy requirements, simplicity of process and product quality. (Author)

  10. Biofuel from hydrothermal carbonisation of biomass

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez Latorre, Marisa [Ingelia, Valencia (Spain)], e-mail: marisa.hernandez@ingelia.com

    2012-11-01

    Main Characteristics of biocoal HTC. Ingelia produce these coal pellets from different types of organic material, such as pruning of gardens and parks, biomass from forest cleaning and agricultural crops.

  11. Protein measurements of microalgal and cyanobacterial biomass.

    Science.gov (United States)

    López, Cynthia Victoria González; García, María del Carmen Cerón; Fernández, Francisco Gabriel Acién; Bustos, Cristina Segovia; Chisti, Yusuf; Sevilla, José María Fernández

    2010-10-01

    The protein content of dry biomass of the microalgae Porphyridium cruentum, Scenedesmus almeriensis, and Muriellopsis sp. and of the cyanobacteria Synechocystis aquatilis and Arthrospira platensis was measured by the Lowry method following disruption of the cells by milling with inert ceramic particles. The measurements were compared with the Kjeldahl method and by elemental analysis. The nitrogen-to-protein conversion factors for biomass obtained from exponentially growing cells with a steady state doubling time of approximately 23 h were 5.95 for nitrogen measured by Kjeldahl and 4.44 for total nitrogen measured by elemental analysis. The protein content in dry biomass ranged from 30% to 55%. The above conversion factors are useful for estimating the protein content of microalgal biomass produced in rapid steady state growth as encountered in many commercial production processes.

  12. Polyhydroxyalkanoate copolymers from forest biomass.

    Science.gov (United States)

    Keenan, Thomas M; Nakas, James P; Tanenbaum, Stuart W

    2006-07-01

    The potential for the use of woody biomass in poly-beta-hydroxyalkanoate (PHA) biosynthesis is reviewed. Based on previously cited work indicating incorporation of xylose or levulinic acid (LA) into PHAs by several bacterial strains, we have initiated a study for exploring bioconversion of forest resources to technically relevant copolymers. Initially, PHA was synthesized in shake-flask cultures of Burkholderia cepacia grown on 2.2% (w/v) xylose, periodically amended with varying concentrations of levulinic acid [0.07-0.67% (w/v)]. Yields of poly(beta-hydroxybutyrate-co-beta-hydroxyvalerate) [P(3HB-co-3HV)] from 1.3 to 4.2 g/l were obtained and could be modulated to contain from 1.0 to 61 mol% 3-hydroxyvalerate (3HV), as determined by 1H and 13C NMR analyses. No evidence for either the 3HB or 4HV monomers was found. Characterization of these P(3HB-co-3HV) samples, which ranged in molecular mass (viscometric, Mv) from 511-919 kDa, by differential scanning calorimetry and thermogravimetric analyses (TGA) provided data which were in agreement for previously reported P(3HB-co-3HV) copolymers. For these samples, it was noted that melting temperature (Tm) and glass transition temperature (Tg) decreased as a function of 3HVcontent, with Tm demonstrating a pseudoeutectic profile as a function of mol% 3HV content. In order to extend these findings to the use of hemicellulosic process streams as an inexpensive carbon source, a detoxification procedure involving sequential overliming and activated charcoal treatments was developed. Two such detoxified process hydrolysates (NREL CF: aspen and CESF: maple) were each fermented with appropriate LA supplementation. For the NREL CF hydrolysate-based cultures amended with 0.25-0.5% LA, P(3HB-co-3HV) yields, PHA contents (PHA as percent of dry biomass), and mol% 3HV compositions of 2.0 g/l, 40% (w/w), and 16-52 mol% were obtained, respectively. Similarly, the CESF hydrolysate-based shake-flask cultures yielded 1.6 g/l PHA, 39% (w

  13. Bioenergy Project Development and Biomass Supply

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-07-01

    Modern biomass, and the resulting useful forms of bioenergy produced from it, are anticipated by many advocates to provide a significant contribution to the global primary energy supply of many IEA member countries during the coming decades. For non-member countries, particularly those wishing to achieve economic growth as well as meet the goals for sustainable development, the deployment of modern bioenergy projects and the growing international trade in biomass-based energy carriers offer potential opportunities.

  14. Closed photobioreactors for production of microalgal biomasses.

    Science.gov (United States)

    Wang, Bei; Lan, Christopher Q; Horsman, Mark

    2012-01-01

    Microalgal biomasses have been produced industrially for a long history for application in a variety of different fields. Most recently, microalgae are established as the most promising species for biofuel production and CO(2) bio-sequestration owing to their high photosynthesis efficiency. Nevertheless, design of photobioreactors that maximize solar energy capture and conversion has been one of the major challenges in commercial microalga biomass production. In this review, we systematically survey the recent developments in this field.

  15. Direct conversion of algal biomass to biofuel

    Science.gov (United States)

    Deng, Shuguang; Patil, Prafulla D; Gude, Veera Gnaneswar

    2014-10-14

    A method and system for providing direct conversion of algal biomass. Optionally, the method and system can be used to directly convert dry algal biomass to biodiesels under microwave irradiation by combining the reaction and combining steps. Alternatively, wet algae can be directly processed and converted to fatty acid methyl esters, which have the major components of biodiesels, by reacting with methanol at predetermined pressure and temperature ranges.

  16. Process for the treatment of lignocellulosic biomass

    Science.gov (United States)

    Dale, Bruce E.

    2014-07-08

    A process for the treatment of biomass to render structural carbohydrates more accessible and/or digestible using concentrated ammonium hydroxide with or without anhydrous ammonia addition, is described. The process preferably uses steam to strip ammonia from the biomass for recycling. The process yields of monosaccharides from the structural carbohydrates are good, particularly as measured by the enzymatic hydrolysis of the structural carbohydrates. The monosaccharides are used as animal feeds and energy sources for ethanol production.

  17. Process for the treatment of lignocellulosic biomass

    Science.gov (United States)

    Dale, Bruce E.; Lynd, Lee R.; Laser, Mark

    2013-03-12

    A process for the treatment of biomass to render structural carbohydrates more accessible and/or digestible using concentrated ammonium hydroxide with or without anhydrous ammonia addition, is described. The process preferably uses steam to strip ammonia from the biomass for recycling. The process yields of monosaccharides from the structural carbohydrates are good, particularly as measured by the enzymatic hydrolysis of the structural carbohydrates. The monosaccharides are used as animal feeds and energy sources for ethanol production.

  18. Levulinic acid production from waste biomass

    OpenAIRE

    Anna Maria Raspolli Galletti,; Claudia Antonetti; Valentina De Luise,; Domenico Licursi,; Nicoletta Nassi

    2012-01-01

    The hydrothermal conversion of waste biomass to levulinic acid was investigated in the presence of homogeneous acid catalysts. Different cheap raw materials (poplar sawdust, paper mill sludge, tobacco chops, wheat straw, olive tree pruning) were employed as substrates. The yields of levulinic acid were improved by optimization of the main reaction parameters, such as type and amount of acid catalyst, temperature, duration, biomass concentration, and electrolyte addition. The catalytic perform...

  19. Appendix B - GPRA06 biomass program documentation

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2009-01-18

    This appendix discusses the assumptions and methods employed in the biomass benefits analysis that is part of the fiscal year 2006 GPRA benefits analysis for all of the Department of Energy’s Energy Efficiency and Renewable Energy (EERE) research and deployment programs. The biomass benefits analysis focuses on the benefits of future achievements by the program and excludes retrospective benefits and benefits resulting from industry’s own initiative and funding.

  20. EMERY BIOMASS GASIFICATION POWER SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Benjamin Phillips; Scott Hassett; Harry Gatley

    2002-11-27

    Emery Recycling Corporation (now Emery Energy Company, LLC) evaluated the technical and economical feasibility of the Emery Biomass Gasification Power System (EBGPS). The gasifier technology is owned and being developed by Emery. The Emery Gasifier for this project was an oxygen-blown, pressurized, non-slagging gasification process that novelly integrates both fixed-bed and entrained-flow gasification processes into a single vessel. This unique internal geometry of the gasifier vessel will allow for tar and oil destruction within the gasifier. Additionally, the use of novel syngas cleaning processes using sorbents is proposed with the potential to displace traditional amine-based and other syngas cleaning processes. The work scope within this project included: one-dimensional gasifier modeling, overall plant process modeling (ASPEN), feedstock assessment, additional analyses on the proposed syngas cleaning process, plant cost estimating, and, market analysis to determine overall feasibility and applicability of the technology for further development and commercial deployment opportunities. Additionally, the project included the development of a detailed technology development roadmap necessary to commercialize the Emery Gasification technology. Process modeling was used to evaluate both combined cycle and solid oxide fuel cell power configurations. Ten (10) cases were evaluated in an ASPEN model wherein nine (9) cases were IGCC configurations with fuel-to-electricity efficiencies ranging from 38-42% and one (1) case was an IGFC solid oxide case where 53.5% overall plant efficiency was projected. The cost of electricity was determined to be very competitive at scales from 35-71 MWe. Market analysis of feedstock availability showed numerous market opportunities for commercial deployment of the technology with modular capabilities for various plant sizes based on feedstock availability and power demand.

  1. Biomass equipments. The wood-fueled heating plants; Materiels pour la biomasse. Les chaudieres bois

    Energy Technology Data Exchange (ETDEWEB)

    Chieze, B. [SA Compte R, 63 - Arlanc (France)

    1997-12-31

    This paper analyzes the consequences of the classification of biomass fuels in the French 2910 by-law on the classification of biomass-fueled combustion installations. Biomass fuels used in such installations must be only wood wastes without any treatment or coating. The design of biomass combustion systems must follow several specifications relative to the fueling system, the combustion chamber, the heat exchanger and the treatment of exhaust gases. Other technical solutions must be studied for other type of wood wastes in order to respect the environmental pollution laws. (J.S.)

  2. Evaluation on Microalgae Biomass for Bioethanol Production

    Science.gov (United States)

    Chng, L. M.; Lee, K. T.; Chan, D. C. J.

    2017-06-01

    The depletion of energy resources has triggered worldwide concern for alternative sources, especially renewable energy. Microalgae biomass offers the most promising feedstock for renewable energy because of their impressive efficient growing characteristics and valuable composition. Simple cell structure of the microalgae would simplify the pretreatment technology thus increase the cost-effectiveness of biofuel production. Scenedesmus dimorphus is a carbohydrate-rich microalgae that has potential as biomass for bioethanol. The cultivation of Scenedesmus dimorphus under aeration of carbon dioxide enriched air resulted 1.47 g/L of dry biomass with composition of 12 w/w total lipid, 53.7 w/w carbohydrate and 17.4 protein. Prior to ethanolic fermentation with Saccharomyces cerevisiae, various pre-treatment methods were investigated to release and degrade the complex carbohydrate in cell biomass thus obtaining the maximal amount of digestible sugar for ethanolic yeast. In this study, sulfuric acid was used as hydrolysis agent while amyloglucosidase as enzymatic agent. Dried biomass via hydrothermal acidic hydrolysis yielded sugar which is about 89 of total carbohydrate at reaction temperature of 125 °C and acid concentration of 4 v/v. While combination of organosolv treatment (mixture of methanol and chloroform) with enzymatic hydrolysis yielded comparable amount of sugar with 0.568 g glucose/g treated-biomass. In this study, the significant information in pre-treatment process ensures the sustainability of the biofuel produced.

  3. Electricity production by advanced biomass power systems

    Energy Technology Data Exchange (ETDEWEB)

    Solantausta, Y. [VTT Energy, Espoo (Finland). Energy Production Technologies; Bridgwater, T. [Aston Univ. Birmingham (United Kingdom); Beckman, D. [Zeton Inc., Burlington, Ontario (Canada)

    1996-11-01

    This report gives the results of the Pyrolysis Collaborative Project organized by the International Energy Agency (IEA) under Biomass Agreement. The participating countries or organizations were Canada, European Community (EC), Finland, United States of America, and the United Kingdom. The overall objective of the project was to establish baseline assessments for the performance and economics of power production from biomass. Information concerning the performance of biomass-fuelled power plants based on gasification is rather limited, and even less data is available of on pyrolysis based power applications. In order to gain further insight into the potential for these technologies, this study undertook the following tasks: (1) Prepare process models to evaluate the cost and performance of new advanced biomass power production concepts, (2) Assess the technical and economic uncertainties of different biomass power concepts, (3) Compare the concepts in small scale and in medium scale production (5 - 50 MW{sub e}) to conventional alternatives. Processes considered for this assessment were biomass power production technologies based on gasification and pyrolysis. Direct combustion technologies were employed as a reference for comparison to the processes assessed in this study. Wood was used a feedstock, since the most data was available for wood conversion

  4. Biomass Resource Allocation among Competing End Uses

    Energy Technology Data Exchange (ETDEWEB)

    Newes, E.; Bush, B.; Inman, D.; Lin, Y.; Mai, T.; Martinez, A.; Mulcahy, D.; Short, W.; Simpkins, T.; Uriarte, C.; Peck, C.

    2012-05-01

    The Biomass Scenario Model (BSM) is a system dynamics model developed by the U.S. Department of Energy as a tool to better understand the interaction of complex policies and their potential effects on the biofuels industry in the United States. However, it does not currently have the capability to account for allocation of biomass resources among the various end uses, which limits its utilization in analysis of policies that target biomass uses outside the biofuels industry. This report provides a more holistic understanding of the dynamics surrounding the allocation of biomass among uses that include traditional use, wood pellet exports, bio-based products and bioproducts, biopower, and biofuels by (1) highlighting the methods used in existing models' treatments of competition for biomass resources; (2) identifying coverage and gaps in industry data regarding the competing end uses; and (3) exploring options for developing models of biomass allocation that could be integrated with the BSM to actively exchange and incorporate relevant information.

  5. BARRIER ISSUES TO THE UTILIZATION OF BIOMASS

    Energy Technology Data Exchange (ETDEWEB)

    Jay R. Gunderson; Bruce C. Folkedahl; Darren D. Schmidt; Greg F. Weber; Christopher J. Zygarlicke

    2002-05-01

    The Energy & Environmental Research Center (EERC) is conducting a project to examine the fundamental issues limiting the use of biomass in small industrial steam/power systems in order to increase the future use of this valuable domestic resource. Specifically, the EERC is attempting to elucidate the ash-related problems--grate clinkering and heat exchange surface fouling--associated with cofiring coal and biomass in grate-fired systems. Utilization of biomass in stoker boilers designed for coal can be a cause of concern for boiler operators. Boilers that were designed for low-volatile fuels with lower reactivities can experience damaging fouling when switched to higher-volatile and more reactive lower-rank fuels, such as when cofiring biomass. Higher heat release rates at the grate can cause more clinkering or slagging at the grate because of higher temperatures. Combustion and loss of volatile matter can start too early with biomass fuels compared to design fuel, vaporizing alkali and chlorides which then condense on rear walls and heat exchange tube banks in the convective pass of the boiler, causing noticeable increases in fouling. In addition, stoker-fired boilers that switch to biomass blends may encounter new chemical species such as potassium sulfates and various chlorides in combination with different flue gas temperatures because of changes in fuel heating value, which can adversely affect ash deposition behavior.

  6. Biomassa e energia Biomass and energy

    Directory of Open Access Journals (Sweden)

    José Goldemberg

    2009-01-01

    Full Text Available Biomass was the dominating source of energy for human activities until the middle 19th century, when coal, oil, gas and other energy sources became increasingly important but it still represents ca. 10% of the worldwide energy supply. The major part of biomass for energy is still "traditional biomass" used as wood and coal extracted from native forests and thus non-sustainable, used with low efficiency for cooking and home heating, causing pollution problems. This use is largely done in rural areas and it is usually not supported by trading activities. There is now a strong trend to the modernization of biomass use, especially making alcohol from sugar cane thus replacing gasoline, or biodiesel to replace Diesel oil, beyond the production of electricity and vegetable coal using wood from planted forests. As recently as in 2004, sustainable "modern biomass" represented 2% of worldwide energy consumption. This article discusses the perspectives of the "first" and "second" technology generations for liquid fuel production, as well as biomass gaseification to make electricity or syngas that is in turn used in the Fischer-Tropsch process.

  7. [Estimation of aboveground biomass of desert plants].

    Science.gov (United States)

    Zhao, Chengyi; Song, Yudong; Wang, Yuchao; Jiang, Pinan

    2004-01-01

    Based on the research of plant quadrate in Sangong River Basin in Xinjiang, the fitted equations were given, which could be used to estimate the aboveground biomass of typical desert plant by using the thicket characteristics such as length of crown diameter, width of crown diameter, number of basal branch, length of new branch, basal diameter (D) and plant height (H) as parameters. Using the length of crown diameter and the width of crown diameter as parameters, the fitted equation was set up and tested for estimating the aboveground biomass of Reaumuria soongorica Maxim. It had a relatively high accuracy and a fine linear relationship between the predicted values and measured values. Its coefficient and relative standard deviation was 0.9989 and 4.79%-10.12%, respectively. The results indicated that the fitted equation was easy and available for estimating the aboveground biomass of Reaumuria soongorica Maxim in large scale. The fitted equations were also set up and tested for estimating the aboveground biomass of Haloxylon ammodendron and Tamarix ramosissima by using the basal diameter and height of plant as the parameters. The coefficients and relative standard deviations of these equations were 0.9902, 0.9875 and 6.87%-19.22%, 7.49%-18.47%, respectively. Therefore, estimating the biomass of Reaumuria soongorica in large scale through crown characteristics was available, and estimating the biomass of Halaxylon Ammodendron and Tamarix ramosissima through crown characteristics would produce certain error.

  8. EFFICIENT USE OF BIOMASS IN IMPROVED COOKSTOVES

    Directory of Open Access Journals (Sweden)

    R. K. PAL

    2016-12-01

    Full Text Available Traditional biomass cookstoves have very low efficiency. The improved cookstoves have very high efficiency. These improved cookstoves with high efficiency saves biomass fuels. Biomass can be saved in case of rocket elbow cookstoves. The amount of biomass which can be saved in case of rocket elbow cookstoves is 65.88 MT. More biomass can be saved in case of gasifier fan cookstoves. The amount of biomass which can be saved is 155.71 MT. The pollutants like particulate matter, black carbon, carbon mono-oxide and carbon dioxide emission is lesser in case of rocket elbow cookstoves. The pollutants are least in case of gasifier fan cookstoves. The reduction in particulate matter, black carbon, carbon mono-oxide and carbon dioxide emission in gasifier fan cookstoves is 1.77 MT, 0.24 MT, 0.71 MT & 151.64 MT respectively in comparison to traditional cookstoves. Therefore indoor air pollution is greatly reduced in case of improved cookstoves especially in case of gasifier fan cookstoves as compared to traditional cookstoves.

  9. Preparation of gasification feedstock from leafy biomass.

    Science.gov (United States)

    Shone, C M; Jothi, T J S

    2016-05-01

    Dried leaves are a potential source of energy although these are not commonly used beside to satisfy daily energy demands in rural areas. This paper aims at preparing a leafy biomass feedstock in the form of briquettes which can be directly used for combustion or to extract the combustible gas using a gasifier. Teak (Tectona grandis) and rubber (Hevea brasiliensis) leaves are considered for the present study. A binder-assisted briquetting technique with tapioca starch as binder is adopted. Properties of these leafy biomass briquettes such as moisture content, calorific value, compressive strength, and shatter index are determined. From the study, briquettes with biomass-to-binder ratio of 3:5 are found to be stable. Higher mass percentage of binder is considered for preparation of briquettes due to the fact that leafy biomasses do not adhere well on densification with lower binder content. Ultimate analysis test is conducted to analyze the gasification potential of the briquettes. Results show that the leafy biomass prepared from teak and rubber leaves has calorific values of 17.5 and 17.8 MJ/kg, respectively, which are comparable with those of existing biomass feedstock made of sawdust, rice husk, and rice straw.

  10. Biomass production by freshwater and marine macrophytes

    Energy Technology Data Exchange (ETDEWEB)

    North, W.J.; Gerard, V.A.; Kuwabara, J.S.

    1981-01-01

    Research on aquatic macrophytes as producers of biomass has been undertaken at Woods Hole Oceanographic Institution (WHOI) on the east coast and on the west coast by a group of collaborators in a joint effort known as the Marine Biomass Project. Studies at WHOI have focused on estuarine and coastal situations with some attention recently to freshwater plants. The Marine Farm Project has primarily been concerned with oceanic biomass production. A group at WHOI has undertaken a wide variety of studies concerning aquatic macrophytes including nutrient uptake, growth, yields, and environmental factors affecting yields. Aquatic biomass production systems have been surveyed on a worldwide basis and currently the role of carbon as a potential limiting nutrient in biomass culturing is being examined. The Marine Farm Project is presently attempting to grow giant kelp in offshore waters off southern California. Other work related to aquatic biomass production includes an investigation at the University of California, Berkeley, of microalgae in ponds. This paper will emphasize discussion of the kelp production phases of the Marine Farm Project. Activities by the WHOI are briefly summarized.

  11. BIOMASS SUPPLY CHAIN ANALYSIS WITH DENSIFIED WASTE

    Directory of Open Access Journals (Sweden)

    Elisangela Fernandes da Silva Campana Possidônio

    2016-04-01

    Full Text Available ABSTRACT The possibility to vary the energy matrix, thus reducing the dependency on fossil fuels, has amplified the acceptance of biomass as an alternative fuel. Despite being a cheap and renewable option and the fact that Brazil is a major producer of waste from agriculture and forestry activities, the use of these materials has barriers due to its low density and low energetic efficiency, which can raise the costs of its utilization. Biomass densification has drawn attention due to its advantage in comparison to in natura biomass due to its better physical and combustion characteristics. The objective of this paper is to evaluate the impact of biomass densification in distribution and transport costs. To reach this objective, a mathematical model was used to represent decisions at a supply chain that coordinates the purchase and sale of forestry and wood waste. The model can evaluate the options to deliver biomass through the supply chain combining demand meeting and low cost. Results point to the possibility of an economy of 60% in transport cost and a reduction of 63% in the required quantity of trucks when densified waste is used. However, costs related to the densifying process lead to an increase of total supply costs of at least 37,8% in comparison to in natura waste. Summing up, the viability of biomass briquettes industry requires a cheaper densification process.

  12. 76 FR 9339 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2011-02-17

    ... of Energy Efficiency and Renewable Energy Biomass Research and Development Technical Advisory... Open Meeting. SUMMARY: This notice announces an open meeting of the Biomass Research and Development... on USDA Biomass R&D Activities. Update on DOE Biomass R&D Activities. Overview of the DOE...

  13. 76 FR 63614 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2011-10-13

    ... Doc No: 2011-26476] DEPARTMENT OF ENERGY Energy Efficiency and Renewable Energy Biomass Research and.... ACTION: Notice of open meeting. SUMMARY: This notice announces an open meeting of the Biomass Research... Update on USDA Biomass R&D Activities; Update on DOE Biomass R&D Activities; Presentation on...

  14. Method of producing hydrogen, and rendering a contaminated biomass inert

    Science.gov (United States)

    Bingham, Dennis N [Idaho Falls, ID; Klingler, Kerry M [Idaho Falls, ID; Wilding, Bruce M [Idaho Falls, ID

    2010-02-23

    A method for rendering a contaminated biomass inert includes providing a first composition, providing a second composition, reacting the first and second compositions together to form an alkaline hydroxide, providing a contaminated biomass feedstock and reacting the alkaline hydroxide with the contaminated biomass feedstock to render the contaminated biomass feedstock inert and further producing hydrogen gas, and a byproduct that includes the first composition.

  15. 48 CFR 1452.237-71 - Utilization of Woody Biomass.

    Science.gov (United States)

    2010-10-01

    ... Biomass. 1452.237-71 Section 1452.237-71 Federal Acquisition Regulations System DEPARTMENT OF THE INTERIOR... Utilization of Woody Biomass. As prescribed in § 1437.7202, insert the following clause: Utilization of Woody Biomass (MAY 2005) (a) The contractor may remove and utilize woody biomass, if: (1) Project work...

  16. Kinetic investigation for slow combustion of biomass

    Energy Technology Data Exchange (ETDEWEB)

    Haykiri-Acma, H.; Yaman, S. [Istanbul Technical Univ., Istanbul (Turkey). Dept. of Chemical Engineering, Faculty of Chemical and Metallurgical Engineering

    2006-07-01

    The renewed interest in biomass as a renewable, clean, and inexpensive fuel was discussed. Many different mechanisms take place simultaneously during biomass combustion and also during other thermal processes such as gasification, pyrolysis or carbonization. These mechanisms have a pronounced influence on the design and operation of thermal conversion processes. In addition, product yields and product distributions from the thermal processes are sensitive to the kinetic properties of biomass. In order to evaluate the combustion mechanisms and the combustion kinetics of biomass, the behavior of these constituents under combustion conditions were properly evaluated. In this study, combustion of biomass samples was carried out in a thermogravimetric analyzer by heating them from ambient to 1173 K with heating rates of 5 K/min and 10 K/min under dynamic dry air atmosphere of 40 mL/min. The biomass samples included olive refuse, sunflower seed shell, rapeseed, grape seed, and hybrid poplar. The purpose of the study was to examine the kinetic properties of biomass during slow combustion for the overall combustion process as well as for some definite temperature intervals at which different combustion mechanisms are present according to the type and complexity of biomass used. Derivative thermogravimetric analysis (DTG) curves were derived, and data obtained from these curves were used to compute the kinetic parameters such as activation energy, pre-exponential factor, and governing mechanisms for the combustion processes. The governing mechanisms for individual temperature intervals were examined along with the overall combustion process. The study showed that at lower temperature intervals, the combustion process was controlled primarily by the chemical reaction. At least 3 sequential mechanisms may occur at different temperature intervals during combustion of biomass. Activation energy and pre-exponential factors were determined for each temperature interval

  17. Carbonic Acid Pretreatment of Biomass

    Energy Technology Data Exchange (ETDEWEB)

    G. Peter van Walsum; Kemantha Jayawardhana; Damon Yourchisin; Robert McWilliams; Vanessa Castleberry

    2003-05-31

    This project sought to address six objectives, outlined below. The objectives were met through the completion of ten tasks. 1) Solidify the theoretical understanding of the binary CO2/H2O system at reaction temperatures and pressures. The thermodynamics of pH prediction have been improved to include a more rigorous treatment of non-ideal gas phases. However it was found that experimental attempts to confirm theoretical pH predictions were still off by a factor of about 1.8 pH units. Arrhenius experiments were carried out and the activation energy for carbonic acid appears to be substantially similar to sulfuric acid. Titration experiments have not yet confirmed or quantified the buffering or acid suppression effects of carbonic acid on biomass. 2) Modify the carbonic acid pretreatment severity function to include the effect of endogenous acid formation and carbonate buffering, if necessary. It was found that the existing severity functions serve adequately to account for endogenous acid production and carbonate effects. 3) Quantify the production of soluble carbohydrates at different reaction conditions and severity. Results show that carbonic acid has little effect on increasing soluble carbohydrate concentrations for pretreated aspen wood, compared to pretreatment with water alone. This appears to be connected to the release of endogenous acids by the substrate. A less acidic substrate such as corn stover would derive benefit from the use of carbonic acid. 4) Quantify the production of microbial inhibitors at selected reaction conditions and severity. It was found that the release of inhibitors was correlated to reaction severity and that carbonic acid did not appear to increase or decrease inhibition compared to pretreatment with water alone. 5) Assess the reactivity to enzymatic hydrolysis of material pretreated at selected reaction conditions and severity. Enzymatic hydrolysis rates increased with severity, but no advantage was detected for the use of carbonic

  18. Carbonic Acid Retreatment of Biomass

    Energy Technology Data Exchange (ETDEWEB)

    Baylor university

    2003-06-01

    This project sought to address six objectives, outlined below. The objectives were met through the completion of ten tasks. (1) Solidify the theoretical understanding of the binary CO{sub 2}/H{sub 2}O system at reaction temperatures and pressures. The thermodynamics of pH prediction have been improved to include a more rigorous treatment of non-ideal gas phases. However it was found that experimental attempts to confirm theoretical pH predictions were still off by a factor of about 1.8 pH units. Arrhenius experiments were carried out and the activation energy for carbonic acid appears to be substantially similar to sulfuric acid. Titration experiments have not yet confirmed or quantified the buffering or acid suppression effects of carbonic acid on biomass. (2) Modify the carbonic acid pretreatment severity function to include the effect of endogenous acid formation and carbonate buffering, if necessary. It was found that the existing severity functions serve adequately to account for endogenous acid production and carbonate effects. (3) Quantify the production of soluble carbohydrates at different reaction conditions and severity. Results show that carbonic acid has little effect on increasing soluble carbohydrate concentrations for pretreated aspen wood, compared to pretreatment with water alone. This appears to be connected to the release of endogenous acids by the substrate. A less acidic substrate such as corn stover would derive benefit from the use of carbonic acid. (4) Quantify the production of microbial inhibitors at selected reaction conditions and severity. It was found that the release of inhibitors was correlated to reaction severity and that carbonic acid did not appear to increase or decrease inhibition compared to pretreatment with water alone. (5) Assess the reactivity to enzymatic hydrolysis of material pretreated at selected reaction conditions and severity. Enzymatic hydrolysis rates increased with severity, but no advantage was detected for

  19. Quantifying the Carbon Intensity of Biomass Energy

    Science.gov (United States)

    Hodson, E. L.; Wise, M.; Clarke, L.; McJeon, H.; Mignone, B.

    2012-12-01

    Regulatory agencies at the national and regional level have recognized the importance of quantitative information about greenhouse gas emissions from biomass used in transportation fuels or in electricity generation. For example, in the recently enacted California Low-Carbon Fuel Standard, the California Air Resources Board conducted a comprehensive study to determine an appropriate methodology for setting carbon intensities for biomass-derived transportation fuels. Furthermore, the U.S. Environmental Protection Agency is currently conducting a multi-year review to develop a methodology for estimating biogenic carbon dioxide (CO2) emissions from stationary sources. Our study develops and explores a methodology to compute carbon emission intensities (CIs) per unit of biomass energy, which is a metric that could be used to inform future policy development exercises. To compute CIs for biomass, we use the Global Change Assessment Model (GCAM), which is an integrated assessment model that represents global energy, agriculture, land and physical climate systems with regional, sectoral, and technological detail. The GCAM land use and land cover component includes both managed and unmanaged land cover categories such as food crop production, forest products, and various non-commercial land uses, and it is subdivided into 151 global land regions (wiki.umd.edu/gcam), ten of which are located in the U.S. To illustrate a range of values for different biomass resources, we use GCAM to compute CIs for a variety of biomass crops grown in different land regions of the U.S. We investigate differences in emissions for biomass crops such as switchgrass, miscanthus and willow. Specifically, we use GCAM to compute global carbon emissions from the land use change caused by a marginal increase in the amount of biomass crop grown in a specific model region. Thus, we are able to explore how land use change emissions vary by the type and location of biomass crop grown in the U.S. Direct

  20. Method and a Mobile Unit for Collecting Biomass

    DEFF Research Database (Denmark)

    2011-01-01

    A method for collecting biomass, such as straw, and for producing a pyrolysis liquid, such as oil or tar, from the biomass, comprises the step of collecting the biomass from a growth site, e.g. a field, by means of a mobile unit. The biomass is continuously fed into a pyrolysis apparatus (200) ac...... for forcing biomass towards a reactive surface in a pyrolysis reactor. The mobile unit may be self-propelled....

  1. FIA's volume-to-biomass conversion method (CRM) generally underestimates biomass in comparison to published equations

    Science.gov (United States)

    David. C. Chojnacky

    2012-01-01

    An update of the Jenkins et al. (2003) biomass estimation equations for North American tree species resulted in 35 generalized equations developed from published equations. These 35 equations, which predict aboveground biomass of individual species grouped according to a taxa classification (based on genus or family and sometimes specific gravity), generally predicted...

  2. Production of methanol/DME from biomass

    Energy Technology Data Exchange (ETDEWEB)

    Ahrenfeldt, J.; Birk Henriksen, U.; Muenster-Swendsen, J.; Fink, A.; Roengaard Clausen, L.; Munkholt Christensen, J.; Qin, K.; Lin, W.; Arendt Jensen, P.; Degn Jensen, A.

    2011-07-01

    In this project the production of DME/methanol from biomass has been investigated. Production of DME/methanol from biomass requires the use of a gasifier to transform the solid fuel to a synthesis gas (syngas) - this syngas can then be catalytically converted to DME/methanol. Two different gasifier types have been investigated in this project: 1) The Two-Stage Gasifier (Viking Gasifier), designed to produce a very clean gas to be used in a gas engine, has been connected to a lab-scale methanol plant, to prove that the gas from the gasifier could be used for methanol production with a minimum of gas cleaning. This was proved by experiments. Thermodynamic computer models of DME and methanol plants based on using the Two-Stage Gasification concept were created to show the potential of such plants. The models showed that the potential biomass to DME/methanol + net electricity energy efficiency was 51-58% (LHV). By using waste heat from the plants for district heating, the total energy efficiencies could reach 87-88% (LHV). 2) A lab-scale electrically heated entrained flow gasifier has been used to gasify wood and straw. Entrained flow gasifiers are today the preferred gasifier type for commercial coal gasification, but little information exists on using these types of gasifiers for biomass gasification. The experiments performed provided quantitative data on product and gas composition as a function of operation conditions. Biomass can be gasified with less oxygen consumption compared to coal. The organic fraction of the biomass that is not converted to gas appears as soot. Thermodynamic computer models of DME and methanol plants based on using entrained flow gasification were created to show the potential of such plants. These models showed that the potential torrefied biomass to DME/methanol + net electricity energy efficiency was 65-71% (LHV). Different routes to produce liquid transport fuels from biomass are possible. They include production of RME (rapeseed oil

  3. Swiss Biomass Programme - Overview report on the 2007 research programme; Programm Biomasse: Ueberblicksbericht zum Forschungsprogramm 2007

    Energy Technology Data Exchange (ETDEWEB)

    Binggeli, D.; Guggisberg, B.

    2008-07-01

    This illustrated report for the Swiss Federal Office of Energy (SFOE) presents an overview of the results obtained in 2007 within the framework of the Swiss Biomass research programme. The potential for biomass use in Switzerland is reviewed and the emphases of the national programme are discussed. The results obtained are noted for the following areas: process optimisation, including - amongst others - particle emissions and control aspects as well as combined wood-pellets and solar heating systems. Projects involving non-wood biomass are reported on, including biomass digesters and various biogas systems. Further reports deal with the analysis and optimisation of material flows, organic pollutants and methane losses. New conversion technologies are reported on. Further reports deal with basic strategies and concepts in the area of biomass usage. National and international co-operation is also discussed. A selection of innovative pilot and demonstration projects is also presented and research and development projects are listed.

  4. Effects of solubility properties of solvents and biomass on biomass pretreatment.

    Science.gov (United States)

    Weerachanchai, Piyarat; Kwak, Sang Kyu; Lee, Jong-Min

    2014-10-01

    Hildebrand solubility parameters of biomasses and pretreatment solvents were examined by a method of intrinsic viscosity. This is to be used as basic information in selecting a suitable solvent for biomass pretreatment processes. The effects of mixing1-ethyl-3-methylimidazolium acetate (EMIM-AC) and different solvents, lignin content in a pretreatment solvent, and biomass type on the Hildebrand solubility parameter and thermodynamic properties were carried out and calculated in this work. The Hildebrand solubility parameters of the mixtures are according to those of organic solvents: δH[EMIM-AC/DMA]=25.07biomass compositions (microcrystalline cellulose, xylan and alkali lignin) and biomasses (cassava pulp residue and rice straw) vary in the ranges of 25.14-26.13. The increases of lignin content in the pretreatment solvents lead to the Hildebrand solubility parameter becoming closer to that of lignin.

  5. Algal biofuels from urban wastewaters: maximizing biomass yield using nutrients recycled from hydrothermal processing of biomass.

    Science.gov (United States)

    Selvaratnam, T; Pegallapati, A K; Reddy, H; Kanapathipillai, N; Nirmalakhandan, N; Deng, S; Lammers, P J

    2015-04-01

    Recent studies have proposed algal cultivation in urban wastewaters for the dual purpose of waste treatment and bioenergy production from the resulting biomass. This study proposes an enhancement to this approach that integrates cultivation of an acidophilic strain, Galdieria sulphuraria 5587.1, in a closed photobioreactor (PBR); hydrothermal liquefaction (HTL) of the wet algal biomass; and recirculation of the nutrient-rich aqueous product (AP) of HTL to the PBR to achieve higher biomass productivity than that could be achieved with raw wastewater. The premise is that recycling nutrients in the AP can maintain optimal C, N and P levels in the PBR to maximize biomass growth to increase energy returns. Growth studies on the test species validated growth on AP derived from HTL at temperatures from 180 to 300°C. Doubling N and P concentrations over normal levels in wastewater resulted in biomass productivity gains of 20-25% while N and P removal rates also doubled.

  6. Biomass compositional analysis for energy applications.

    Science.gov (United States)

    Hames, Bonnie R

    2009-01-01

    In its broadest definition, biomass can be described as all material that was or is a part of a living organism. For renewable energy applications, however, the definition of biomass is usually limited to include only materials that are plant-derived such as agricultural residues (e.g., wheat straw, corn stover) by-products of industrial processes (e.g., sawdust, sugar cane bagasse, pulp residues, distillers grains), or dedicated energy crops (e.g., switchgrass, sorghum, Miscanthus, short-rotation woody crops). This chapter describes analytical methods developed to measure plant components with an emphasis on the measurement of components that are important for biomass conversion. The methods described here can be viewed as a portfolio of analytical methods, with consistent assumptions and compatible sample preparation steps, selected for simplicity, robust application, and the ability to obtain a summative mass closure on most samples that accurately identifies greater than 95% of the mass of a plant biomass sample. The portfolio of methods has been successfully applied to a wide variety of biomass feedstock as well as liquid and solid fractions of both thermochemical pretreatment and enzymatic saccharification (1).

  7. Chemicals from biomass - BioForest

    Energy Technology Data Exchange (ETDEWEB)

    Heiningen, A. van (Aalto University School of Chemical Technology, Espoo (Finland), Dept. of Forest Products Technology), e-mail: adriaan.vanheiningen@aalto.fi; Granstroem, T. (Aalto University School of Chemical Technology, Espoo (Finland), Dept.of Biotechnology and Chemical Technology), e-mail: tom.granstrom@aalto.fi

    2011-11-15

    The objective of the BioForest project is to develop the science and technology of a series of integrated processing steps which economically convert mixed hardwood and softwood biomass and recycled fibers into commodity chemicals at an existing forest products complex which also produces wood and/or pulp and paper. The commodity products will be produced from the biomass carbohydrates using a novel biomass fractionation process, a modified ABE (Acetone- Butanol-Ethanol) fermentation process, and a novel continuous solvent recovery method from the fermentation liquid. The mixture of solvents produced by the modified ABE process consists of isopropanol, butanol and ethanol. The key technological barriers which have been accomplished in the Bioforest project are following: 1. Fundamental understanding of the kinetics of delignification, hemicellulose dissolution and cellulose degradation during SEW fractionation of softwood and hardwood 2. Optimization of SEW fractionation of softwood biomass with a total treatment time as short as 30 minutes 3. Simultaneous SEW fractionation of hardwood and softwood biomass 4. Production of a high concentration (> 100 g/L) hemicellulose monosugar solution from SEW spent fractionation liquor at a sugar yield larger than 85% by multistep conditioning 5. Construction of E.coli strain harboring isopropanol dehydrogenase gene capable of acetone conversion to isopropanol 6. Successful fermentation of the conditioned hemicellulose monosugar solution to ABE (Acetone, Butanol, Ethanol) solvents using advanced column technology (patent pending) or semi-solid pulp fermentations with the volumetric productivities of 5.5 and 13.5 g/L h respectively. (orig.)

  8. Biomass Compositional Analysis for Energy Applications

    Science.gov (United States)

    Hames, Bonnie R.

    In its broadest definition, biomass can be described as all material that was or is a part of a living organism. For renewable energy applications, however, the definition of biomass is usually limited to include only materials that are plant-derived such as agricultural residues (e.g., wheat straw, corn stover) by-products of industrial processes (e.g., sawdust, sugar cane bagasse, pulp residues, distillers grains), or dedicated energy crops (e.g., switchgrass, sorghum, Miscanthus, short-rotation woody crops). This chapter describes analytical methods developed to measure plant components with an emphasis on the measurement of components that are important for biomass conversion. The methods described here can be viewed as a portfolio of analytical methods, with consistent assumptions and compatible sample preparation steps, selected for simplicity, robust application, and the ability to obtain a summative mass closure on most samples that accurately identifies greater than 95% of the mass of a plant biomass sample. The portfolio of methods has been successfully applied to a wide variety of biomass feedstock as well as liquid and solid fractions of both thermochemical pretreatment and enzymatic saccharification (1).

  9. Investigation of Heat Generation from Biomass Fuels

    Directory of Open Access Journals (Sweden)

    Naoharu Murasawa

    2015-06-01

    Full Text Available New biomass fuels are constantly being developed from renewable resources in an effort to counter global warming and to create a sustainable society based on recycling. Among these, biomass fuels manufactured from waste are prone to microbial fermentation, and are likely to cause fires and explosions if safety measures, including sufficient risk assessments and long-term storage, are not considered. In this study, we conducted a series of experiments on several types of newly developed biomass fuels, using combinations of various thermal- and gas-analysers, to identify the risks related to heat- and gas-generation. Since a method for the evaluation of the relative risks of biomass fuels is not yet established in Japan, we also such a method based on our experimental results. The present study found that in cases where safety measures are not thoroughly observed, biomass fuels manufactured from waste materials have a higher possibility of combusting spontaneously at the storage site due to microbial fermentation and heat generation.

  10. Water vapor release from biomass combustion

    Directory of Open Access Journals (Sweden)

    R. S. Parmar

    2008-10-01

    Full Text Available We report on the emission of water vapor from biomass combustion. Concurrent measurements of carbon monoxide and carbon dioxide are used to scale the concentrations of water vapor found, and are referenced to carbon in the biomass. The investigated fuel types include hardwood (oak and African musasa, softwood (pine and spruce, partly with green needles, and African savanna grass. The session-averaged ratio of H2O to the sum of CO and CO2 in the emissions from 16 combustion experiments ranged from 1.2 to 3.7, indicating the presence of water that is not chemically bound. This non-bound biomass moisture content ranged from 33% in the dry African hardwood, musasa, to 220% in fresh pine branches with needles. The moisture content from fresh biomass contributes significantly to the water vapor in biomass burning emissions, and its influence on the behavior of fire plumes and pyro-cumulus clouds needs to be evaluated.

  11. Empowerment model of biomass in west java

    Science.gov (United States)

    Mulyana, C.; Fitriani, N. I.; Saad, A.; Yuliah, Y.

    2017-06-01

    Scarcity of fossil energy accelerates the search of renewable energy sources as the substitution. In West Java, biomass has potential to be developed into bio-briquette because the resources are abundant. The objectives of this research are mapping the potency of biomass as bio-briquette in West Java, and making the model of the empowerment biomass potential involving five fundamental step which are raw material, pre-processing process, conversion mechanism, products, and end user. The main object of this model focused on 3 forms which are solid, liquid, and gas which was made by involving the community component as the owner biomass, district government, academics and researcher communities, related industries as users of biomass, and the central government as the policy holders and investors as a funder. In the model was described their respective roles and mutual relationship one with another so that the bio-briquette as a substitute of fossil fuels can be realized. Application of this model will provide the benefits in renewability energy sources, environmental, socio economical and energy security.

  12. Green Gasification Technology for Wet Biomass

    Directory of Open Access Journals (Sweden)

    W. H. Chong

    2010-12-01

    Full Text Available The world now is facing two energy related threats which are lack of sustainable, secure and affordable energy supplies and the environmental damage acquired in producing and consuming ever-increasing amount of energy. In the first decade of the twenty-first century, increasing energy prices reminds us that an affordable energy plays an important role in economic growth and human development. To overcome the abovementioned problem, we cannot continue much longer to consume finite reserves of fossil fuels, the use of which contributes to global warming. Preferably, the world should move towards more sustainable energy sources such as wind energy, solar energy and biomass. However, the abovementioned challenges may not be met solely by introduction of sustainable energy forms. We also need to use energy more efficiently. Developing and introducing more efficient energy conversion technologies is therefore important, for fossil fuels as well as renewable fuels. This assignment addresses the question how biomass may be used more efficiently and economically than it is being used today. Wider use of biomass, a clean and renewable feedstock may extend the lifetime of our fossil fuels resources and alleviate global warming problems. Another advantage of using of biomass as a source of energy is to make developed countries less interdependent on oil-exporting countries, and thereby reduce political tension. Furthermore, the economies of agricultural regions growing energy crops benefit as new jobs are created. Keywords: energy, gasification, sustainable, wet biomass

  13. A review on biomass as a fuel for boilers

    Energy Technology Data Exchange (ETDEWEB)

    Saidur, R.; Abelaziz, E.A.; Demirbas, A.; Hossain, M.S.; Mekhilef, S. [University of Malaya, Kuala Lumpur (Malaysia). Dept. of Mechanical Engineering

    2011-06-15

    Currently, fossil fuels such as oil, coal and natural gas represent the prime energy sources in the world. However, it is anticipated that these sources of energy will deplete within the next 40-50 years. Moreover, the expected environmental damages such as the global warming, acid rain and urban smog due to the production of emissions from these sources have tempted the world to try to reduce carbon emissions by 80% and shift towards utilizing a variety of renewable energy resources (RES) which are less environmentally harmful such as solar, wind, biomass etc. in a sustainable way. Biomass is one of the earliest sources of energy with very specific properties. In this review, several aspects which are associated with burning biomass in boilers have been investigated such as composition of biomass, estimating the higher heating value of biomass, comparison between biomass and other fuels, combustion of biomass, co-firing of biomass and coal, impacts of biomass, economic and social analysis of biomass, transportation of biomass, densification of biomass, problems of biomass and future of biomass. It has been found that utilizing biomass in boilers offers many economical, social and environmental benefits such as financial net saving, conservation of fossil fuel resources, job opportunities creation and CO{sub 2} and NO emissions reduction. However, care should be taken to other environmental impacts of biomass such as land and water resources, soil erosion, loss of biodiversity and deforestation. Fouling, marketing, low heating value, storage and collections and handling are all associated problems when burning biomass in boilers. The future of biomass in boilers depends upon the development of the markets for fossil fuels and on policy decisions regarding the biomass market.

  14. Biomass energy: Another driver of land acquisitions?

    Energy Technology Data Exchange (ETDEWEB)

    Cotula, Lorenzo; Finnegan, Lynn; MacQueen, Duncan

    2011-08-15

    As governments in the global North look to diversify their economies away from fossil fuel and mitigate climate change, plans for biomass energy are growing fast. These are fuelling a sharp rise in the demand for wood, which, for some countries, could outstrip domestic supply capacity by as much as 600 per cent. It is becoming clear that although these countries will initially look to tap the temperate woodlands of developed countries, there are significant growth rate advantages that may lead them to turn to the tropics and sub-tropics to fill their biomass gap in the near future. Already there is evidence of foreign investors acquiring land in Africa, South America and Southeast Asia to establish tree plantations for biomass energy. If left unchecked, these trends could increase pressures on land access and food security in some of the world's poorest countries and communities.

  15. Biomass Burning Emissions from Fire Remote Sensing

    Science.gov (United States)

    Ichoku, Charles

    2010-01-01

    Knowledge of the emission source strengths of different (particulate and gaseous) atmospheric constituents is one of the principal ingredients upon which the modeling and forecasting of their distribution and impacts depend. Biomass burning emissions are complex and difficult to quantify. However, satellite remote sensing is providing us tremendous opportunities to measure the fire radiative energy (FRE) release rate or power (FRP), which has a direct relationship with the rates of biomass consumption and emissions of major smoke constituents. In this presentation, we will show how the satellite measurement of FRP is facilitating the quantitative characterization of biomass burning and smoke emission rates, and the implications of this unique capability for improving our understanding of smoke impacts on air quality, weather, and climate. We will also discuss some of the challenges and uncertainties associated with satellite measurement of FRP and how they are being addressed.

  16. Ethanol from biomass: A status report

    Energy Technology Data Exchange (ETDEWEB)

    Walker, R. [SWAN Biomass Co., Downers Grove, IL (United States)

    1996-12-31

    Programmatic and technical activities of SWAN Biomass, a company formed by Amoco Corporation and Stone & Webster, to convert non-grain biomass material to ethanol, are highlighted in this presentation. The potential ethanol markets identified are: (1) fuel oxygenate and octane additive, and (2) waste reduction in the agricultural and forestry industries and in municipal waste streams. Differences in the SWAN process from that used in corn-based ethanol facilities include more intense pretreatment of lignocellulosic biomass, different enzymes, hydrolysis and fermentation of sugar polymers is performed in the same vessel, and a typical solid residue of lignin. The major market and technical risks have been assessed as being manageable. 8 figs., 8 tabs.

  17. SERI biomass program annual technical report: 1982

    Energy Technology Data Exchange (ETDEWEB)

    Bergeron, P.W.; Corder, R.E.; Hill, A.M.; Lindsey, H.; Lowenstein, M.Z.

    1983-02-01

    The biomass with which this report is concerned includes aquatic plants, which can be converted into liquid fuels and chemicals; organic wastes (crop residues as well as animal and municipal wastes), from which biogas can be produced via anerobic digestion; and organic or inorganic waste streams, from which hydrogen can be produced by photobiological processes. The Biomass Program Office supports research in three areas which, although distinct, all use living organisms to create the desired products. The Aquatic Species Program (ASP) supports research on organisms that are themselves processed into the final products, while the Anaerobic Digestion (ADP) and Photo/Biological Hydrogen Program (P/BHP) deals with organisms that transform waste streams into energy products. The P/BHP is also investigating systems using water as a feedstock and cell-free systems which do not utilize living organisms. This report summarizes the progress and research accomplishments of the SERI Biomass Program during FY 1982.

  18. Cofiring biomass with coal: Opportunities for Malaysia

    Science.gov (United States)

    Rahman, A. A.; Shamsuddin, A. H.

    2013-06-01

    Malaysia generated 108,175 GWh of electricity in 2010 where 39.51 % was sourced from coal. Coal power generation is also planned to overtake natural gas as the main fuel for electricity generation within the next two decades. Malaysia also has a vast biomass resource that is currently under-utilised for electricity generation. This paper studies the option of cofiring biomass in existing Malaysian coal power plants to increase the nation's renewable energy mix as well as to reduce its power sector carbon dioxide emission. Benefits of cofiring to the nation were discussed and agricultural residues from palm oil and paddy was identified as a potential source of biomass for cofiring. It was also found that there is a willingness for cofiring by stakeholders but barriers existed in the form of technical issues and lack of clear direction and mechanism.

  19. Synthetic and Biomass Alternate Fueling in Aviation

    Science.gov (United States)

    Hendricks, R.C.; Bushnell, D.M.

    2009-01-01

    Worldwide, aviation alone uses 85 to 95 billion gallons of nonrenewable fossil fuel per year (2008). General transportation fueling can accommodate several different fuels; however, aviation fuels have very specific requirements. Biofuels have been flight demonstrated, are considered renewable, have the capacity to become "drop-in" replacements for Jet-A fuel, and solve the CO2 climate change problem. The major issue is cost; current biomass biofuels are not economically competitive. Biofuel feedstock sources being researched are halophytes, algae, cyanobacteria, weeds-to-crops, wastes with contingent restraints on use of crop land, freshwater, and climate change. There are five major renewable energy sources: solar thermal, solar photovoltaic, wind, drilled geothermal and biomass, each of which have an order of magnitude greater capacity to meet all energy needs. All five address aspects of climate change; biomass has massive potential as an energy fuel feedstock.

  20. Hydrothermal pretreatment of biomass for pellet production

    Energy Technology Data Exchange (ETDEWEB)

    Tooyserkani, Z. [British Columbia Univ., Vancouver, BC (Canada). Clean Energy Research Centre, Biomass and Bioenergy Research Group

    2010-07-01

    This presentation discussed innovative technologies for the production of wood pellets using the hydrothermal pre-treatment of biomass. Conventional techniques use low-cost mill residues, such as saw dust and shavings, as feedstock to produce durable, low-ash pellets. However, mill residues are becoming less available as a result of fewer saw mills, increased pellet production, and increased competition for saw dust. Advanced techniques use mixed biomass such as logging residue as feedstock, creating pellets that are durable for handling and long-term storage, of a higher energy density for transport and mixing with coal for co-firing, and a choice feedstock for biofuels. Advanced pellet production uses steam explosion/pre-treatment in which biomass receives a short-term high-pressure steam treatment followed by sudden decompression. Mild torrefaction seems to have positive feedback, and steam-treated pellets are durable with superior hydrophobicity. 3 figs., 3 tabs.

  1. BARRIER ISSUES TO THE UTILIZATION OF BIOMASS

    Energy Technology Data Exchange (ETDEWEB)

    Greg F. Weber; Christopher J. Zygarlicke

    2001-05-01

    In summary, stoker-fired boilers that cofire or switch to biomass fuel may potentially have to deal with ash behavior issues such as production of different concentrations and quantities of fine particulate or aerosols and ash-fouling deposition. Stoker boiler operators that are considering switching to biomass and adding potential infrastructure to accommodate the switch may also at the same time be looking into upgrades that will allow for generating additional power for sale on the grid. This is the case for the feasibility study being done currently for a small (<1-MW) stoker facility at the North Dakota State Penitentiary, which is considering not only the incorporation of a lower-cost biomass fuel but also a refurbishing of the stoker boiler to burn slightly hotter with the ability to generate more power and sell excess energy on the grid. These types of fuel and boiler changes can greatly affect ash behavior issues.

  2. Biomass Burning Emissions from Fire Remote Sensing

    Science.gov (United States)

    Ichoku, Charles

    2010-01-01

    Knowledge of the emission source strengths of different (particulate and gaseous) atmospheric constituents is one of the principal ingredients upon which the modeling and forecasting of their distribution and impacts depend. Biomass burning emissions are complex and difficult to quantify. However, satellite remote sensing is providing us tremendous opportunities to measure the fire radiative energy (FRE) release rate or power (FRP), which has a direct relationship with the rates of biomass consumption and emissions of major smoke constituents. In this presentation, we will show how the satellite measurement of FRP is facilitating the quantitative characterization of biomass burning and smoke emission rates, and the implications of this unique capability for improving our understanding of smoke impacts on air quality, weather, and climate. We will also discuss some of the challenges and uncertainties associated with satellite measurement of FRP and how they are being addressed.

  3. Biomass fuelled indirect fired micro turbine

    Energy Technology Data Exchange (ETDEWEB)

    Pritchard, D.

    2005-07-01

    This report summarises the findings of a project to further develop and improve a system based on the Bowman TG50 50kWe turbine and a C3(S) combustor with a high temperature heat exchanger for the production of electricity from biomass. Details are given of the specific aims of the project, the manufacture of a new larger biomass combustor, the development of startup and shutdown procedures, waste heat recuperation, adaption of a PC-based mathematical model, and capital equipment costs. The significant levels of carbon emission savings and the commercial prospects of the biomass generator gas turbine combined heat and power (CHP) system are considered, and recommendations are presented.

  4. Switchgrass a valuable biomass crop for energy

    CERN Document Server

    2012-01-01

    The demand of renewable energies is growing steadily both from policy and from industry which seeks environmentally friendly feed stocks. The recent policies enacted by the EU, USA and other industrialized countries foresee an increased interest in the cultivation of energy crops; there is clear evidence that switchgrass is one of the most promising biomass crop for energy production and bio-based economy and compounds. Switchgrass: A Valuable Biomass Crop for Energy provides a comprehensive guide to  switchgrass in terms of agricultural practices, potential use and markets, and environmental and social benefits. Considering this potential energy source from its biology, breed and crop physiology to its growth and management to the economical, social and environmental impacts, Switchgrass: A Valuable Biomass Crop for Energy brings together chapters from a range of experts in the field, including a foreword from Kenneth P. Vogel, to collect and present the environmental benefits and characteristics of this a ...

  5. Putney Basketville Site Biomass CHP Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Hunsberger, Randolph [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mosey, Gail [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2013-10-01

    The U.S. Environmental Protection Agency (EPA) Office of Solid Waste and Emergency Response Center for Program Analysis developed the RE-Powering America's Land initiative to reuse contaminated sites for renewable energy generation when aligned with the community's vision for the site. The Putney, Vermont, Basketville site, formerly the location of a basket-making facility and a paper mill andwoolen mill, was selected for a feasibility study under the program. Biomass was chosen as the renewable energy resource based on abundant woody-biomass resources available in the area. Biomass combined heat and power (CHP) was selected as the technology due to nearby loads, including Putney Paper and Landmark College.

  6. Study of Corrosion in a Biomass Boiler

    Directory of Open Access Journals (Sweden)

    C. Berlanga

    2013-01-01

    Full Text Available Biomass plants, apart from producing energy, help to reduce CO2(g emissions. One of the biggest problems for their development is superheater corrosion due to fuel corrosivity, especially of the straw. This limits both the temperature of the vapour and also the effectiveness of the plant. In order to know more about the reactions which happen inside the boiler of biomass, thermodynamic calculations using software (HSC Chemistry have been carried out. Field tests have been carried out in the Sangüesa Biomass Plant in Navarra (Spain: determination of the types of oxides and the deposits formed on the superheaters tubes as well as a program to measure temperatures. Finally, the global results are discussed.

  7. Woody biomass production systems for Florida

    Energy Technology Data Exchange (ETDEWEB)

    Rockwood, D.L.; Pathak, N.N.; Satapathy, P.C. (Florida Univ., Gainesville, FL (United States). Dept. of Forestry)

    1993-01-01

    Woody biomass production research in Florida has addressed genetic improvement, coppice productivity, clonal propagation, biomass properties, and economics of Eucalyptus and other species in short rotation, intensive culture systems. Improved E. grandis seedlings could more than double productivity, but exceptional clones offer more immediate potential in southern Florida. E. tereticornis and E. camaldulensis appear to have frost-resistance and good growth in central and southern Florida. For northern Florida, E. amplifolia has good frost-resilience and coppicing ability. Eucalytpus species are suitable for fermentation processes. Other promising species include Casuarina glauca and Taxodium distichum in southern Florida, and Sapium sebiferum state-wide. Break-even costs for biomass production systems with Eucalyptus range from approximately $2.00 to $4.00 GJ[sup -1]; short rotation culture appears feasible for slash pine in northern and central Florida but cannot yet be advised for sand pine. (author)

  8. An Experimental Research of Biomass Crushing System

    Science.gov (United States)

    Xia, Yue

    2017-05-01

    Biomass crushing is precondition for utilization and transformation of biomass energy. Compressive strength of biomass raw materials is generally small with long fiber, and multiple crushing methods like shocking, shearing and grinding should be used to realize high-efficiency crushing. Based on this, this paper researched and developed a set of biomass fine crushing system, and conducted an optimized study of main parameters influencing crushing process—revolving speed, between blade and cutter head and material moisture content. Results indicated that this set of crushing system could complete fine crushing of biomass, particle size of crushed products was controlled below 250µm, crushing energy consumption was between 70—120kwh/t, both of which were mainly decided by material moisture content and operating parameters of crusher. Revolving speed of crusher was elevated, proportion of particles (d<106µm) with fine particle size in crushed products increased, and unit energy consumption of crushing increased; narrowing space between blade and cutter head could improve crushing effect of biomass, but unit energy consumption increased; the higher the moisture content was, the less the content of fine particles in crushed products would be, and the greater unit energy consumption would be. By comprehensive comparison, the optimal operating conditions for crushing were: revolving speed was 3600r/min, space between impulse blade and cutter head was 8mm, moisture content was 10.6%, energy consumption was 98kwh/t, product particle size distribution was: those with particle size below 106µm occupied 71.5% and those between 106µm—250µm occupied 28.5%.

  9. Validating Community-Led Forest Biomass Assessments.

    Science.gov (United States)

    Venter, Michelle; Venter, Oscar; Edwards, Will; Bird, Michael I

    2015-01-01

    The lack of capacity to monitor forest carbon stocks in developing countries is undermining global efforts to reduce carbon emissions. Involving local people in monitoring forest carbon stocks could potentially address this capacity gap. This study conducts a complete expert remeasurement of community-led biomass inventories in remote tropical forests of Papua New Guinea. By fully remeasuring and isolating the effects of 4,481 field measurements, we demonstrate that programmes employing local people (non-experts) can produce forest monitoring data as reliable as those produced by scientists (experts). Overall, non-experts reported lower biomass estimates by an average of 9.1%, equivalent to 55.2 fewer tonnes of biomass ha(-1), which could have important financial implications for communities. However, there were no significant differences between forest biomass estimates of expert and non-expert, nor were there significant differences in some of the components used to calculate these estimates, such as tree diameter at breast height (DBH), tree counts and plot surface area, but were significant differences between tree heights. At the landscape level, the greatest biomass discrepancies resulted from height measurements (41%) and, unexpectedly, a few large missing trees contributing to a third of the overall discrepancies. We show that 85% of the biomass discrepancies at the tree level were caused by measurement taken on large trees (DBH ≥50 cm), even though they consisted of only 14% of the stems. We demonstrate that programmes that engage local people can provide high-quality forest carbon data that could help overcome barriers to reducing forest carbon emissions in developing countries. Nonetheless, community-based monitoring programmes should prioritise reducing errors in the field that lead to the most important discrepancies, notably; overcoming challenges to accurately measure large trees.

  10. Biomass thermochemical conversion program. 1985 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Schiefelbein, G.F.; Stevens, D.J.; Gerber, M.A.

    1986-01-01

    Wood and crop residues constitute a vast majority of the biomass feedstocks available for conversion, and thermochemical processes are well suited for conversion of these materials. The US Department of Energy (DOE) is sponsoring research on this conversion technology for renewable energy through its Biomass Thermochemical Conversion Program. The Program is part of DOE's Biofuels and Municipal Waste Technology Division, Office of Renewable Technologies. This report briefly describes the Thermochemical Conversion Program structure and summarizes the activities and major accomplishments during fiscal year 1985. 32 figs., 4 tabs.

  11. Production of chemicals and fuels from biomass

    Energy Technology Data Exchange (ETDEWEB)

    Woods, Elizabeth; Qiao, Ming; Myren, Paul; Cortright, Randy D.; Kania, John

    2015-12-15

    Described are methods, reactor systems, and catalysts for converting biomass to fuels and chemicals in a batch and/or continuous process. The process generally involves the conversion of water insoluble components of biomass, such as hemicellulose, cellulose and lignin, to volatile C.sub.2+O.sub.1-2 oxygenates, such as alcohols, ketones, cyclic ethers, esters, carboxylic acids, aldehydes, and mixtures thereof. In certain applications, the volatile C.sub.2+O.sub.1-2 oxygenates can be collected and used as a final chemical product, or used in downstream processes to produce liquid fuels, chemicals and other products.

  12. New market potential: Torrefaction of woody biomass

    Energy Technology Data Exchange (ETDEWEB)

    Tumuluru, Jaya Shankar [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hess, J. Richard [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-06-02

    Biomass was the primary source of energy worldwide until a few generations ago, when the energy-density, storability and transportability of fossil fuels enabled one of the most rapid cultural transformations in the history of humankind: the industrial revolution. In just a few hundred years, coal, oil and natural gas have prompted the development of highly efficient, high-volume manufacturing and transportation systems that have become the foundation of the world economy. But over-reliance on fossil resources has also led to environmental and energy security concerns. In addition, one of the greatest advantages of using biomass to replace fossil fuels is reduced greenhouse gas emissions and carbon footprint.

  13. High Temperature Corrosion in Biomass Incineration Plants

    DEFF Research Database (Denmark)

    Montgomery, Melanie; Maahn, Ernst emanuel; Gotthjælp, K.

    1997-01-01

    The aim of the project is to study the role of ash deposits in high temperature corrosion of superheater materials in biomass and refuse fire combined heat and power plants. The project has included the two main activities: a) A chemical characterisation of ash deposits collected from a major...... number of biomass and refuse fired combined heat and power plant boilers, b) Laboratory exposures and metallurgical examinations of material specimens with ash deposits in well-defined gas environments with HCl and SO2 in a furnace....

  14. Biomass Gasifier Facility (BGF). Environmental Assessment

    Energy Technology Data Exchange (ETDEWEB)

    1992-09-01

    The Pacific International Center for High Technology Research (PICHTR) is planning, to design, construct and operate a Biomass Gasifier Facility (BGF). This facility will be located on a site easement near the Hawaiian Commercial & Sugar company (KC&S) Paia Sugar Factory on Maui, Hawaii. The proposed BGF Project is a scale-up facility, intended to demonstrate the technical and economic feasibility of emerging biomass gasification technology for commercialization. This Executive Summary summarizes the uses of this Environmental Assessment, the purpose and need for the project, project,description, and project alternatives.

  15. Production of methanol/DME from biomass

    DEFF Research Database (Denmark)

    Ahrenfeldt, Jesper; Henriksen, Ulrik Birk; Münster-Swendsen, Janus;

    -58% (LHV). By using waste heat from the plants for district heating, the total energy efficiencies could reach 87-88% (LHV). • A lab-scale electrically heated entrained flow gasifier has been used to gasify wood and straw. Entrained flow gasifiers are today the preferred gasifier type for commercial coal...... gasification, but little information exists on using these types of gasifiers for biomass gasification. The experiments performed provided quantitative data on product and gas composition as a function of operation conditions. Biomass can be gasified with less oxygen consumption compared to coal. The organic...

  16. BARRIER ISSUES TO THE UTILIZATION OF BIOMASS

    Energy Technology Data Exchange (ETDEWEB)

    Bruce C. Folkedahl; Darren D. Schmidt; Greg F. Weber; Christopher J. Zygarlicke

    2001-10-01

    The Energy & Environmental Research Center (EERC) is conducting a project to examine the fundamental issues limiting the use of biomass in small industrial steam/power systems in order to increase the future use of this valuable domestic resource. Specifically, the EERC is attempting to elucidate the ash-related problems--grate clinkering and heat exchange surface fouling--associated with cofiring coal and biomass in grate-fired systems. Utilization of biomass in stoker boilers designed for coal can be a cause of concern for boiler operators. Boilers that were designed for low volatile fuels with lower reactivities can experience damaging fouling when switched to higher volatile and more reactive lower-rank fuels, such as when cofiring biomass. Higher heat release rates at the grate can cause more clinkering or slagging at the grate because of higher temperatures. Combustion and loss of volatile matter can start too early for biomass fuels compared to the design fuel, vaporizing alkali and chlorides which then condense on rear walls and heat exchange tube banks in the convective pass of the stoker, causing noticeable increases in fouling. In addition, stoker-fired boilers that switch to biomass blends may encounter new chemical species such as potassium sulfates and various chlorides, in combination with different flue gas temperatures because of changes in fuel heating value which can adversely affect ash deposition behavior. The goal of this project is to identify the primary ash mechanisms related to grate clinkering and heat exchange surface fouling associated with cofiring coal and biomass--specifically wood and agricultural residuals--in grate-fired systems, leading to future mitigation of these problems. The specific technical objectives of the project are: Modification of an existing EERC pilot-scale combustion system to simulate a grate-fired system; Verification testing of the simulator; Laboratory-scale testing and fuel characterization to determine ash

  17. BARRIER ISSUES TO THE UTILIZATION OF BIOMASS

    Energy Technology Data Exchange (ETDEWEB)

    Bruce C. Folkedahl; Jay R. Gunderson; Darren D. Schmidt; Greg F. Weber; Christopher J. Zygarlicke

    2002-09-01

    The Energy & Environmental Research Center (EERC) has completed a project to examine fundamental issues that could limit the use of biomass in small industrial steam/power systems in order to increase the future use of this valuable domestic resource. Specifically, the EERC attempted to elucidate the ash-related problems--grate clinkering and heat exchange surface fouling--associated with cofiring coal and biomass in grate-fired systems. Utilization of biomass in stoker boilers designed for coal can be a cause of concern for boiler operators. Boilers that were designed for low-volatile fuels with lower reactivities can experience problematic fouling when switched to higher-volatile and more reactive coal-biomass blends. Higher heat release rates at the grate can cause increased clinkering or slagging at the grate due to higher temperatures. Combustion and loss of volatile matter can start much earlier for biomass fuels compared to design fuel, vaporizing alkali and chlorides which then condense on rear walls and heat exchange tube banks in the convective pass of the stoker, causing noticeable increases in fouling. In addition, stoker-fired boilers that switch to biomass blends may encounter new chemical species such as potassium sulfates, various chlorides, and phosphates. These species in combination with different flue gas temperatures, because of changes in fuel heating value, can adversely affect ash deposition behavior. The goal of this project was to identify the primary ash mechanisms related to grate clinkering and heat exchange surface fouling associated with cofiring coal and biomass--specifically wood and agricultural residuals--in grate-fired systems, leading to future mitigation of these problems. The specific technical objectives of the project were: (1) Modification of an existing pilot-scale combustion system to simulate a grate-fired system. (2) Verification testing of the simulator. (3) Laboratory-scale testing and fuel characterization to

  18. Genetic manipulation of lignocellulosic biomass for bioenergy.

    Science.gov (United States)

    Wang, Peng; Dudareva, Natalia; Morgan, John A; Chapple, Clint

    2015-12-01

    Lignocellulosic biomass represents an abundant and sustainable raw material for biofuel production. The recalcitrance of biomass to degradation increases the estimated cost of biofuel production and limits its competitiveness in the market. Genetic engineering of lignin, a major recalcitrance factor, improves saccharification and thus the potential yield of biofuels. Recently, our understanding of lignification and its regulation has been advanced by new studies in various systems, all of which further enhances our ability to manipulate the biosynthesis and deposition of lignin in energy crops for producing cost-effective second generation biofuels.

  19. Modeling and analysis of biomass production systems

    Energy Technology Data Exchange (ETDEWEB)

    Mishoe, J.W.; Lorber, M.N.; Peart, R.M.; Fluck, R.C.; Jones, J.W.

    1984-01-01

    BIOMET is an interactive simulation model that is used to analyze specific biomass and methane production systems. The system model is composed of crop growth models, harvesting, transportation, conversion and economic submodels. By use of menus the users can configure the structure and set selected parameters of the system to analyze the effects of variables within the component models. For example, simulations of a water hyacinth system resulted in yields of 63, 48 and 37 mg/ha/year for different harvest schedules. For napier grass, unit methane costs were $3.04, $2.86 and $2.98 for various yields of biomass. 10 references.

  20. Catalytic routes from biomass to fuels

    DEFF Research Database (Denmark)

    Riisager, Anders

    2014-01-01

    The carbon-based chemicals and fuels that are necessary to meet the energy demand for our society originate presently almost exclusively from inexpensive fossil resources – coal, oil and natural gas. The forecast of diminishing and more expensive petroleum reserves has, however, engaged...... chain unaffected. This presentation will survey the status of biofuels production from different sources, and discuss the sustainability of making transportation fuels from biomass. Furthermore, recently developed chemocatalytic technologies that allow efficient conversion of lignocellulosic biomass...... components into transportation fuels and fuel additives will be highlighted....

  1. Adhesion Strength of Biomass Ash Deposits

    DEFF Research Database (Denmark)

    Laxminarayan, Yashasvi; Jensen, Peter Arendt; Wu, Hao

    2015-01-01

    This study investigates the shear adhesion strength of biomass ash deposits on superheater tubes. Artificial biomass ash deposits were prepared on superheater tubes and sintered in an oven at temperatures up to 1000°C. Subsequently, the deposits were sheared off with the help of an electrically...... controlled arm. Higher sintering temperatures resulted in greater adhesion strengths, with a sharp increase observed near the melting point of the ash. Repetition of experiments with fixed operation conditions revealed considerable variation in the obtained adhesion strengths, portraying the stochastic...

  2. Water vapor release from biomass combustion

    OpenAIRE

    Parmar, R. S.; Welling, M.; Andreae, M. O.; G. Helas

    2008-01-01

    We report on the emission of water vapor from biomass combustion. Concurrent measurements of carbon monoxide and carbon dioxide are used to scale the concentrations of water vapor found, and are referenced to carbon in the biomass. The investigated fuel types include hardwood (oak and African musasa), softwood (pine and spruce, partly with green needles), and African savanna grass. The session-averaged ratio of H2O to the sum of CO and CO2 in the ...

  3. Molecular Scale Drivers of Biomass Recalcitrance

    DEFF Research Database (Denmark)

    Selig, Michael Joseph

    The thesis focus on the basic parameters limiting the breakdown of biomass to sugars. There is a multitude of structures and compounds in the plant cell wall which limits the performance of hydrolytic enzymes. In this thesis it is shown how the interactions between water and the cell wall...... components can be used as a measure of biomass recalcitrance as well as unspecific bonding of enzymes to the cell wall components. The different states of water in the plant cell wall is presented and discussed in relation to enzyme adsorption and activity....

  4. Forest Biomass for Climate Change Mitigation

    DEFF Research Database (Denmark)

    Nielsen, Anders Tærø

    on southern Scandinavian sites, managed under different systems both in agriculture and in forests. In addition, the objective is to assess the potential of the poplar plantations to mitigate climate change by using poplar biomass for substitution of fossil fuels in comparison to a traditional product......Awareness of elevated CO2 levels in the atmosphere and resulting climate change has increased focus on renewable energy sources during recent decades. Biomass for energy has been predicted to have the greatest potential for CO2 reductions in the short term and the IPCC assumes that the use...

  5. Biomass Burning Observation Project Science Plan

    Energy Technology Data Exchange (ETDEWEB)

    Kleinman, KI [Brookhaven National Laboratory; Sedlacek, AJ [Brookhaven National Laboratory

    2013-09-01

    Aerosols from biomass burning perturb Earth’s climate through the direct radiative effect (both scattering and absorption) and through influences on cloud formation and precipitation and the semi-direct effect. Despite much effort, quantities important to determining radiative forcing such as the mass absorption coefficients (MAC) of light-absorbing carbon, secondary organic aerosol (SOA) formation rates, and cloud condensation nuclei (CCN) activity remain in doubt. Field campaigns in northern temperate latitudes have been overwhelmingly devoted to other aerosol sources in spite of biomass burning producing about one-third of the fine particles (PM2.5) in the U.S.

  6. Environmental analysis of biomass-ethanol facilities

    Energy Technology Data Exchange (ETDEWEB)

    Corbus, D.; Putsche, V.

    1995-12-01

    This report analyzes the environmental regulatory requirements for several process configurations of a biomass-to-ethanol facility. It also evaluates the impact of two feedstocks (municipal solid waste [MSW] and agricultural residues) and three facility sizes (1000, 2000, and 3000 dry tons per day [dtpd]) on the environmental requirements. The basic biomass ethanol process has five major steps: (1) Milling, (2) Pretreatment, (3) Cofermentation, (4) Enzyme production, (5) Product recovery. Each step could have environmental impacts and thus be subject to regulation. Facilities that process 2000 dtpd of MSW or agricultural residues would produce 69 and 79 million gallons of ethanol, respectively.

  7. Molecular Scale Drivers of Biomass Recalcitrance

    DEFF Research Database (Denmark)

    Selig, Michael Joseph

    The thesis focus on the basic parameters limiting the breakdown of biomass to sugars. There is a multitude of structures and compounds in the plant cell wall which limits the performance of hydrolytic enzymes. In this thesis it is shown how the interactions between water and the cell wall...... components can be used as a measure of biomass recalcitrance as well as unspecific bonding of enzymes to the cell wall components. The different states of water in the plant cell wall is presented and discussed in relation to enzyme adsorption and activity....

  8. Energy from biomass and wastes: 1979 update

    Energy Technology Data Exchange (ETDEWEB)

    Klass, D.L.

    1979-01-01

    The R and D activities in progress in the United States on the development of biomass and wastes as renewable energy sources have reached the point where all phases of the technology are under active investigation. Highlights of this effort are briefly reviewed from the standpoint of energy impact, funding, carbon dioxide build-up in the atmosphere, and biomass production and its conversion to energy and synthetic fuels. Special attention is given to alcohols because of the current interest in gasohol. Significant accomplishments were reported in 1979, and it is expected that commercial utilization of this information will begin to gather more momentum.

  9. Investigating combustion as a method of processing inedible biomass produced in NASA's biomass production chamber

    Science.gov (United States)

    Dreschel, T. W.; Wheeler, R. M.; Hinkle, C. R.; Sager, J. C.; Knott, W. M.

    1991-01-01

    The Controlled Ecological Life Support System (CELSS) Breadboard Project at the John F. Kennedy Space Center is a research program to integrate and evaluate biological processes to provide air, water, and food for humans in closed environments for space habitation. This project focuses on the use of conventional crop plants as grown in the Biomass Production Chamber (BPC) for the production and recycling of oxygen, food, and water. The inedible portion of these crops has the potential to be converted to edible biomass or directly to the elemental constituents for direct recycling. Converting inedible biomass directly, by combustion, to carbon dioxide, water, and minerals could provide a baseline for estimating partitioning of the mass balance during recycling in a CELSS. Converting the inedible biomass to carbon dioxide and water requires the same amount of oxygen that was produced by photosynthesis. The oxygen produced during crop growth is just equal to the oxygen required to oxidize all the biomass produced during growth. Thus, the amount of oxygen produced that is available for human consumption is in proportion to the amount of biomass actually utilized by humans. The remaining oxygen must be available to oxidize the rest of the biomass back to carbon dioxide and water or the system will not be a regenerative one.

  10. Diagnostics of the BIOMASS feed array prototype

    DEFF Research Database (Denmark)

    Cappellin, Cecilia; Pivnenko, Sergey; Pontoppidan, Kennie Nybo

    2013-01-01

    The 3D reconstruction algorithm is applied to the prototype feed array of the BIOMASS synthetic aperture radar, recently measured at the DTU-ESA Spherical Near-Field Antenna Test Facility in Denmark. Careful analysis of the measured feed array data has shown that the test support structure...

  11. 75 FR 66201 - Biomass Crop Assistance Program

    Science.gov (United States)

    2010-10-27

    ... sugar and starch (other than ethanol derived from corn kernel starch); biofuel derived from waste... mean ``a fuel derived from renewable biomass.'' Corn ethanol would be included in the definition of..., biobased products, or advanced biofuels. For the purposes of BCAP, advanced biofuels do not include...

  12. Process for decomposing lignin in biomass

    Energy Technology Data Exchange (ETDEWEB)

    Rector, Kirk Davin; Lucas, Marcel; Wagner, Gregory Lawrence; Kimball, David Bryan; Hanson, Susan Kloek

    2014-10-28

    A mild inexpensive process for treating lignocellulosic biomass involves oxidative delignification of wood using an aqueous solution prepared by dissolving a catalytic amount of manganese (III) acetate into water and adding hydrogen peroxide. Within 4 days and without agitation, the solution was used to convert poplar wood sections into a fine powder-like delignified, cellulose rich materials that included individual wood cells.

  13. Commodity chemicals from forest biomass - Bioforest

    Energy Technology Data Exchange (ETDEWEB)

    Granstrom, T. [Aalto University, Espoo (Finland)], email: tom.granstrom@aalto.fi

    2012-07-01

    To develop an economic process for production of commodity chemicals from mixed forest biomass (tree tops, limbs, twigs and stumps from softwoods and hardwoods) and recycled fibers within an integrated forest products complex. The chemicals that will be produced are: butanol, isopropanol and ethanol.

  14. Chemicals from biomass - BioForest

    Energy Technology Data Exchange (ETDEWEB)

    van Heiningen, A. (Aalto Univ., Espoo (Finland). Dept. of Forest products Technology), Email: adriaan.vanheiningen@tkk.fi; Granstroem, T. (Aalto Univ. , Espoo (Finland). Dept. of Biotechnology and Chemical Technology), Email: tom.granstrom@tkk.fi

    2010-10-15

    The objective of the BioForest project is to develop the science and technology of a series of integrated processing steps which economically convert mixed hardwood and softwood biomass and recycled fibers into commodity chemicals at an existing forest products complex which produces wood and/or pulp and paper. The commodity products will be produced from the biomass carbohydrates using a novel biomass fractionation process, a modified ABE (Acetone-Butanol-Ethanol) fermentation process, and a novel continuous solvent recovery method from the fermentation liquid. The mixture of solvents produced by the modified ABE process consists of isopropanol, butanol and ethanol. The key technological barriers which will be addressed in the present project are: 1. Production of a high concentration (> 100 g/L) mono sugar solution without costly pretreatment and enzymatic hydrolysis of the biomass, 2. Generation of the modified ABE solvent mixture at high concentration (> 20 g/L) and a fermentation time of 40?60 hours or 4 g/L h productivity, 3. Continuous removal of the ABE solvent mixture from the fermentation broth to overcome the high concentration toxicity of butanol to the Clostridia fermentation strain, and 4. Pretreatment and utilization of recycled fibers for fermentation to ABE solvents. (orig.)

  15. Chemical from biomass - BioForest

    Energy Technology Data Exchange (ETDEWEB)

    Van Heiningen, A. (Helsinki Univ. of Technology, Dept. of Forest Products Technology, Espoo (Finland)), email: adriaan.vanheiningen@tkk.fi; Granstroem, T. (Helsinki Univ. of Technology, Dept. of Biotechnology and Chemical Technology, Espoo (Finland)), email: tom.granstrom@tkk.fi

    2009-10-15

    The objective of the BioForest project is to develop the science and technology of a series of integrated processing steps which economically convert mixed hardwood and softwood biomass and recycled fibers into commodity chemicals at an existing forest products complex which produces wood and/or pulp and paper. The commodity products will be produced from the biomass carbohydrates using a novel biomass fractionation process, a modified ABE (Acetone-Butanol-Ethanol) fermentation process, and a novel continuous solvent recovery method from the fermentation liquid. The mixture of solvents produced by the modified ABE-process consists of isopropanol, butanol and ethanol. The key technological barriers which will be addressed in the present project are: (1) Production of a high concentration (> 100 g/L) mono sugar solution without costly pretreatment and enzymatic hydrolysis of the biomass, (2) Generation of the modified ABE solvent mixture at high concentration (>20 g/L) and a fermentation time of 40-60 hours, Continuous removal of the ABE solvent mixture from the fermentation broth to overcome the high concentration toxicity of butanol to the Clostridia fermentation strain, and (4) Pretreatment and utilization of recycled fibers for fermentation to ABE solvents. (orig.)

  16. Biomass resilience of Neotropical secondary forests

    NARCIS (Netherlands)

    Poorter, Lourens; Bongers, Frans; Aide, T.M.; Almeyda Zambrano, A.M.; Balvanera, Patricia; Jakovac, C.C.; Braga Junqueira, A.; Lohbeck, Madelon; Penã-Claros, Marielos; Rozendaal, D.M.A.

    2016-01-01

    Land-use change occurs nowhere more rapidly than in the tropics, where the imbalance between deforestation and forest regrowth has large consequences for the global carbon cycle. However, considerable uncertainty remains about the rate of biomass recovery in secondary forests, and how these rates

  17. Biomass resilience of Neotropical secondary forests

    NARCIS (Netherlands)

    Poorter, L.; Bongers, F.; Aide, T.M.; Almeyda Zambrano, A.M.; Balvanera, P.; Becknell, J.M.; Boukill, V.; Brancalion, P.H.S.; Jakovac, A.C.; Braga Junqueira, A.; Lohbeck, M.W.M.; Pena Claros, M.; Rozendaal, Danae

    2016-01-01

    Land-use change occurs nowhere more rapidly than in the tropics, where the imbalance between deforestation and forest regrowth has large consequences for the global carbon cycle1. However, considerable uncertainty remains about the rate of biomass recovery in secondary forests, and how these rates a

  18. Nanostructure enzyme assemblies for biomass conversion

    Science.gov (United States)

    Biomass represents a vast resource for production of the world’s fuel and chemical feedstock needs. The use of enzymes to effect these bioconversions offers an alternative that is potentially more specific and environmentally-friendly than harsher chemical methodologies. Some species of anaerobic ...

  19. Air quality on biomass harvesting operations

    Science.gov (United States)

    Dana Mitchell

    2011-01-01

    The working environment around logging operations can be very dusty. But, air quality around logging operations is not well documented. Equipment movements and trafficking on the landing can cause dust to rise into the air. The addition of a biomass chipper creates different air flow patterns and may stir up additional dust. This project addresses two topics related to...

  20. Novel applications of biomass wet pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Sillanpaa, M. [Lappeenranta Univ. of Technology (Finland)], email: mika.sillanpaa@lut.fi

    2012-07-01

    Production of carbonaceous material from unconventional wet biomass sources by thermal processing offers interesting novel opportunities and application possibilities in different fields. Thermal treatment at low temperatures refers to torrefication in general. Disadvantage in this technique is that biomass has to be dried first which consumes a lot energy and time and limits use of biomass materials widely. In wetpyrolysis (hydrothermal carbonization, HTC), biomass source can be wetter, like wood, household wastes, manure or industrial wastewater sludge. Reaction takes place in water environment at higher temperature (180-250 deg C) and pressure which is self-generated. Typically reaction system is high pressure reactor also called autoclave. Comparing to torrefaction HTC produces more solid yield, water soluble organic compounds but formation is low during reaction. Properties of the product can be easily modified by changing reaction conditions, utilization of additives or catalysts. Novel materials obtained by this technique will be used in different applications in water treatment and it will be also interesting to compare purification efficiency of these materials to activated carbon.

  1. Process for decomposing lignin in biomass

    Science.gov (United States)

    Rector, Kirk Davin; Lucas, Marcel; Wagner, Gregory Lawrence; Kimball, David Bryan; Hanson, Susan Kloek

    2014-10-28

    A mild inexpensive process for treating lignocellulosic biomass involves oxidative delignification of wood using an aqueous solution prepared by dissolving a catalytic amount of manganese (III) acetate into water and adding hydrogen peroxide. Within 4 days and without agitation, the solution was used to convert poplar wood sections into a fine powder-like delignified, cellulose rich materials that included individual wood cells.

  2. Hydrothermal pretreatments of macroalgal biomass for biorefineries

    DEFF Research Database (Denmark)

    Ruiz, Héctor A.; Rodríguez-Jasso, Rosa M.; Aguedo, Mario

    2015-01-01

    ecently, macroalgal biomass is gaining wide attention as an alternative in the production of biofuels (as bioetanol and biogas) and compounds with high added value with specific properties (antioxidants, anticoagulants, anti–inflammatories) for applications in food, medical and energy industries ...

  3. SMALL SCALE BIOMASS FUELED GAS TURBINE ENGINE

    Science.gov (United States)

    A new generation of small scale (less than 20 MWe) biomass fueled, power plants are being developed based on a gas turbine (Brayton cycle) prime mover. These power plants are expected to increase the efficiency and lower the cost of generating power from fuels such as wood. The n...

  4. Urban biomass - not an urban legend

    Science.gov (United States)

    Utilizing biomass from urban landscapes could significantly contribute to the nation’s renewable energy needs. There is an estimated 16.4 million hectares of land in urban areas cultivated with turfgrass and associated vegetation. Vegetation in urban areas is intensely managed which lead to regula...

  5. Woody biomass from short rotation energy crops

    Science.gov (United States)

    R.S. Zalesny; M.W. Cunningham; R.B. Hall; J. Mirck; D.L. Rockwood; John Stanturf; T.A. Volk

    2011-01-01

    Short rotation woody crops (SRWCs) are ideal for woody biomass production and management systems because they are renewable energy feedstocks for biofuels, bioenergy, and bioproducts that can be strategically placed in the landscape to conserve soil and water, recycle nutrients, and sequester carbon. This chapter is a synthesis of the regional implications of producing...

  6. Sustainable Production of Switchgrass for Biomass Energy

    Science.gov (United States)

    Switchgrass (Panicum virgatum L.) is a C4 grass native to the North American tallgrass prairies, which historically extended from Mexico to Canada. It is the model perennial warm-season grass for biomass energy. USDA-ARS in Lincoln, NE has studied switchgrass continuously since 1936. Plot-scale rese...

  7. BSCL use plan: Solving biomass recalcitrance

    Energy Technology Data Exchange (ETDEWEB)

    Himmel, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Vinzant, T. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bower, S. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jechura, J. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2005-08-01

    Saccharification of lignocellulosic biomass has long been recognized as a potential low-cost source of mixed sugars for fermentation to fuel ethanol or chemicals. Several technologies have been developed over the years that allow this conversion process to occur, yet the significant challenge remaining is to make the process cost competitive.

  8. Biomass gasification for the production of methane

    NARCIS (Netherlands)

    Nanou, P.

    2013-01-01

    Biomass is very promising as a sustainable alternative to fossil resources because it is a renewable source that contains carbon, an essential building block for gaseous and liquid fuels. Methane is the main component of natural gas, which is a fuel used for heating, power generation and transportat

  9. Forest biodiversity and woody biomass harvesting

    Science.gov (United States)

    Deahn M. Donner; T. Bently Wigley; Darren A. Miller

    2017-01-01

    With the expected increase in demand for woody biomass to help meet renewable energy needs, one principal sustainability question has been whether this material can be removed from forest stands while still conserving biological diversity and retaining ecosystem functioning (Hecht et al. 2009; Berch, Morris, and Malcolm 2011; Ridley et al. 2013). In general,...

  10. Coal + Biomass → Liquids + Electricity (with CCS)

    Science.gov (United States)

    In this presentation, Matt Aitken applies the MARKet ALlocation energy system model to evaluate the market potential for a class of technologies that convert coal and biomass to liquid fuels and electricity (CBtLE), paired with carbon capture and storage (CCS). The technology is ...

  11. Drying of willow biomass in supply chains

    NARCIS (Netherlands)

    Gigler, J.K.

    2000-01-01

    The drying process of willow ( Salix viminalis ) in biomass supply chains to energy plants is quantitatively described. Drying at particle level was modelled for chips and stems by a diffusion equation linked to the mass transfer of moisture to the air. Drying at bulk level is described by a deep be

  12. [Sumac (Rhus chinensis Mill) biomass refinery engineering].

    Science.gov (United States)

    Wang, Lan; Wang, Ning; Li, Tan; Chen, Hongzhang

    2014-05-01

    Sumac (Rhus chinensis Mill) is an abundant and widely distributed Chinese native plant. Sumac fruit contains low content of vegetable oil, as an atypical oil plants hardly being processed through traditional vegetable oil production technologies. Based on our own studies on the characteristics of sumac fruit and branches, we established a novel model of sumac biomass refinery, and constructed the sumac biomass refinery technology system and eco-industrial chain integration. Steam explosion was the key technology, and several components fractionation technologies were integrated in the sumac biomass refinery system. The fractionated components were converted into different products depending on their functional features. Eight products including sumac fruit oil, biodiesel, protein feed, flavonoids, unbleached facial tissue, phenolic resin, biomass briquette and biogas were produced in the refinery. The extracted sumac fruit oil by steam explosion pretreatment was applied for the new food resource of Ministry of Health, and the permit was approved. This research provides a new model for the development of atypical wild plant resources.

  13. Biomass resilience of Neotropical secondary forests

    NARCIS (Netherlands)

    Poorter, Lourens; Bongers, Frans; Aide, T.M.; Almeyda Zambrano, A.M.; Balvanera, Patricia; Jakovac, C.C.; Braga Junqueira, A.; Lohbeck, Madelon; Penã-Claros, Marielos; Rozendaal, D.M.A.

    2016-01-01

    Land-use change occurs nowhere more rapidly than in the tropics, where the imbalance between deforestation and forest regrowth has large consequences for the global carbon cycle. However, considerable uncertainty remains about the rate of biomass recovery in secondary forests, and how these rates

  14. Biomass resilience of Neotropical secondary forests

    NARCIS (Netherlands)

    Poorter, L.; Bongers, F.; Aide, T.M.; Almeyda Zambrano, A.M.; Balvanera, P.; Becknell, J.M.; Boukill, V.; Brancalion, P.H.S.; Jakovac, A.C.; Braga Junqueira, A.; Lohbeck, M.W.M.; Pena Claros, M.; Rozendaal, Danae

    2016-01-01

    Land-use change occurs nowhere more rapidly than in the tropics, where the imbalance between deforestation and forest regrowth has large consequences for the global carbon cycle1. However, considerable uncertainty remains about the rate of biomass recovery in secondary forests, and how these rates a

  15. Wallowa County Integrated Biomass Energy Center

    Energy Technology Data Exchange (ETDEWEB)

    Christoffersen, Nils [Wallowa Resources Community Solutions Inc., Wallowa, OR (United States)

    2014-05-02

    The Integrated Biomass Energy Center (IBEC) is an approximately 0.1 MW CHP integrated biorefinery in Northeastern Oregon which will demonstrate and validate small-scale combined heat and power from lignin intermediates/residues. IBEC will be co-located with feedstock suppliers and thermal and power customers for distributed generation. The project was developed by Wallowa Resources Community Solutions Inc.

  16. Coal + Biomass → Liquids + Electricity (with CCS)

    Science.gov (United States)

    In this presentation, Matt Aitken applies the MARKet ALlocation energy system model to evaluate the market potential for a class of technologies that convert coal and biomass to liquid fuels and electricity (CBtLE), paired with carbon capture and storage (CCS). The technology is ...

  17. BIOMASS-TO-ENERGY FEASIBILITY STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Cecil T. Massie

    2002-09-03

    The purpose of this study was to assess the economic and technical feasibility of producing electricity and thermal energy from biomass by gasification. For an economic model we chose a large barley malting facility operated by Rahr Malting Co. in Shakopee, Minnesota. This plant provides an excellent backdrop for this study because it has both large electrical loads and thermal loads that allowed us to consider a wide range of sizes and technical options. In the end, eleven scenarios were considered ranging from 3.1 megawatts (MWe) to 19.8 MWe. By locating the gasification and generation at an agricultural product processing plant with large electrical and thermal loads, the expectation was that some of the limitations of stand-alone biomass power plants would be overcome. In addition, since the process itself created significant volumes of low value biomass, the hope was that most of the biomass gathering and transport issues would be handled as well. The development of low-BTU gas turbines is expected to fill a niche between the upper limit of multiple spark ignited engine set systems around 5 MWe and the minimum reasonable scale for steam turbine systems around 10 MWe.

  18. Lead removal by Spirulina platensis biomass.

    Science.gov (United States)

    Al-Homaidan, Ali A; Al-Abbad, Aljawharah F; Al-Hazzani, Amal A; Al-Ghanayem, Abdullah A; Alabdullatif, Jamila A

    2016-01-01

    In this investigation, we report on the biosorption of Pb (II) from aqueous solutions by the nonliving biomass of the micro-alga (cyanobacterium) Spirulina platensis. Propagation of the micro-alga was carried out in outside oblong raceway ponds. The biomass was cleaned, dried and used for the investigation. The effects of pH, adsorbent dose, temperature, initial concentration of Pb (II), and contact time on the adsorption of lead by the dry biomass were studied. The experiments were carried out in 250 ml conical flasks containing 100 ml of test solutions using an orbital incubator at 150 rpm. Concentrations of the metal before and after the experiments were measured using Atomic Absorption Spectrophotometer. Very high levels of Pb (II) removal (>91%) were obtained. The optimum conditions for maximal adsorption by S. platensis were found to be pH 3; 2 g of adsorbent dose; incubation at 26°C; 100 mg/l of lead initial concentration and 60 minutes of contact time. The experimental data fitted well with Freundlich isotherm equation with R(2) values greater than 0.97. Based on our results, we recommend the utilization of S. platensis biomass for heavy metal removal from aqueous solutions.

  19. Energy Production from Marine Biomass (Ulva lactuca)

    DEFF Research Database (Denmark)

    Nikolaisen, Lars; Daugbjerg Jensen, Peter; Svane Bech, Karin;

    The background for this research activity is that the 2020 goals for reduction of the CO2 emissions to the atmosphere are so challenging that exorbitant amounts of biomass and other renewable sources of energy must be mobilised in order to – maybe – fulfil the ambitious 2020 goals. The macroalgae...

  20. Drying of willow biomass in supply chains

    NARCIS (Netherlands)

    Gigler, J.

    2000-01-01

    The drying process of willow ( Salix viminalis ) in biomass supply chains to energy plants is quantitatively described. Drying at particle level was modelled for chips and stems by a diffusion equation linked to the mass transfer of moisture to the air. Drying at bulk

  1. Maximum-biomass prediction of homofermentative Lactobacillus.

    Science.gov (United States)

    Cui, Shumao; Zhao, Jianxin; Liu, Xiaoming; Chen, Yong Q; Zhang, Hao; Chen, Wei

    2016-07-01

    Fed-batch and pH-controlled cultures have been widely used for industrial production of probiotics. The aim of this study was to systematically investigate the relationship between the maximum biomass of different homofermentative Lactobacillus and lactate accumulation, and to develop a prediction equation for the maximum biomass concentration in such cultures. The accumulation of the end products and the depletion of nutrients by various strains were evaluated. In addition, the minimum inhibitory concentrations (MICs) of acid anions for various strains at pH 7.0 were examined. The lactate concentration at the point of complete inhibition was not significantly different from the MIC of lactate for all of the strains, although the inhibition mechanism of lactate and acetate on Lactobacillus rhamnosus was different from the other strains which were inhibited by the osmotic pressure caused by acid anions at pH 7.0. When the lactate concentration accumulated to the MIC, the strains stopped growing. The maximum biomass was closely related to the biomass yield per unit of lactate produced (YX/P) and the MIC (C) of lactate for different homofermentative Lactobacillus. Based on the experimental data obtained using different homofermentative Lactobacillus, a prediction equation was established as follows: Xmax - X0 = (0.59 ± 0.02)·YX/P·C.

  2. Column leaching from biomass combustion ashes

    DEFF Research Database (Denmark)

    Maresca, Alberto; Astrup, Thomas Fruergaard

    2015-01-01

    The utilization of biomass combustion ashes for forest soil liming and fertilizing has been addressed in literature. Though, a deep understanding of the ash chemical composition and leaching behavior is necessary to predict potential benefits and environmental risks related to this practice...

  3. Fuel briquettes from biomass-lignite blends

    Energy Technology Data Exchange (ETDEWEB)

    Yaman, S.; Haykiri-Acma, H.; Sesen, K.; Kuecuekbayrak, S. [Chemical Engineering Department, Chemical and Metallurgical Engineering Faculty, Istanbul Technical University, Maslak, 80626 Istanbul (Turkey)

    2001-08-01

    In this study, a western Turkish lignite (Kuetahya-Seyitoemer) was blended with some biomass samples such as molasses, pine cone, olive refuse, sawdust, paper mill waste, and cotton refuse, and these blends was used in the production of fuel briquettes. Blends were subjected to briquetting pressures between 50 and 250 MPa; the ratio of biomass to lignite was changed between 0 and 30 wt.%. The mechanical strength of obtained briquettes was investigated considering shatter index and compressive strength. Effects of the ratio of biomass to lignite and applied pressure on the strength of the briquettes were examined. This study indicated that the mechanical strength of the briquettes produced from Kuetahya-Seyitoemer lignite can be improved by adding some biomass samples. For example, the presence of paper mill waste increased the shatter index of the briquettes obtained. Similarly, sawdust and paper mill waste increased compressive strength of the briquettes. Water resistance of the briquettes can be augmented by adding olive refuse, cotton refuse, pine cone or paper mill waste.

  4. Biomass to energy : turning residue to revenue

    Energy Technology Data Exchange (ETDEWEB)

    Kingston, A. [DynaMotive Energy Systems Corp., Vancouver, BC (Canada)

    2003-07-01

    A business overview of DynaMotive Energy Systems Corp. was presented. The company was founded in 1990 and has developed a fast pyrolysis process called BioTherm{sup TM}, which converts forest and agricultural biomass residue into char and a liquid fuel called BioOil. Fast pyrolysis in a fluidized bed reactor involves the rapid heating of biomass in the absence of oxygen. Feedstocks include bark and whitewood, sugar cane residue, wheat straw, and rice hulls. The environmental advantage of BioTherm technology is that it reduces undesirable emissions to the atmosphere and promotes the use of renewable energy, and waste product utilization. It has been predicted that biomass demand in the future will exceed gas, oil or coal. Other market drivers for the BioTherm process include energy security, energy cost, biomass residue management, and climate change objectives. BioOils can be used as an industrial fuel for boilers, kilns and for district heating. They can also be used as fuel for turbines in power generation. In time, BioOils can be used as a transportation fuel and in chemical refining. This paper described projects currently under development, project financing and output values. It also listed project development partners. 5 tabs., 12 figs.

  5. High Temperature Corrosion in Biomass Incineration Plants

    DEFF Research Database (Denmark)

    Montgomery, Melanie; Maahn, Ernst emanuel; Gotthjælp, K.

    1997-01-01

    The aim of the project is to study the role of ash deposits in high temperature corrosion of superheater materials in biomass and refuse fire combined heat and power plants. The project has included the two main activities: a) A chemical characterisation of ash deposits collected from a major...

  6. Alternative biomass sources for thermal energy generation

    Science.gov (United States)

    Steensen, Torge; Müller, Sönke; Dresen, Boris; Büscher, Olaf

    2015-04-01

    Traditionally, renewable biomass energy sources comprise forests, agriculture and other large vegetation units. With the increasing demand on those landscape elements, including conflicts of interest to nature conservation and food production, the research focus should also incorporate smaller vegetation entities. In this study, we highlight the availability of small-scale features like roadside vegetation or hedges, which are rarely featured in maps. Roadside vegetation, however, is well known and regularly trimmed to allow the passing of traffic but the cut material is rarely harvested. Here, we combine a remote-sensing-based approach to quantify the seasonal biomass harvests with a GIS-based method to outline optimal transportation routes to, and the location of, storage units and power plants. Our main data source will be ESA's upcoming Sentinel-2 optical satellite. Spatial resolution of 10 meters in the visible and near infrared requires the use of spectral unmixing to derive end member spectra of the targeted biomass objects. Additional stereo-matching and LIDAR measurements allow the accompanying height estimate to derive the biomass volume and its changes over time. GIS data bases from the target areas allow the discrimination between traditional, large features (e.g. forests and agriculture) as well as previously unaccounted for, smaller vegetation units. With the mapped biomass occurrence and additional, GIS-based infrastructure information, we can outline transport routes that take into account local restrictions like nature reserve areas, height or weight limitations as well as transport costs in relation to potential gains. This information can then be processed to outline optimal places for power plants. To simulate the upcoming Sentinel-2 data sets, we use airborne data from the AISA Eagle, spatially and spectrally down-sampled to match Sentinel 2's resolution. Our test scenario is an area in western Germany, the Kirchheller Heide, close to the city

  7. Catalytic fast pyrolysis of lignocellulosic biomass

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Changjun; Wang, Huamin; Karim, Ayman M.; Sun, Junming; Wang, Yong

    2014-11-21

    Increasing energy demand, especially in the transportation sector, and soaring CO2 emissions necessitate the exploitation of renewable sources of energy. Despite the large variety of new energy Q3 carriers, liquid hydrocarbon still appears to be the most attractive and feasible form of transportation fuel taking into account the energy density, stability and existing infrastructure. Biomass is an abundant, renewable source of energy; however, utilizing it in a cost-effective way is still a substantial challenge. Lignocellulose is composed of three major biopolymers, namely cellulose, hemicellulose and lignin. Fast pyrolysis of biomass is recognized as an efficient and feasible process to selectively convert lignocellulose into a liquid fuel—bio-oil. However bio-oil from fast pyrolysis contains a large amount of oxygen, distributed in hundreds of oxygenates. These oxygenates are the cause of many negative properties, such as low heating values, high corrosiveness, high viscosity, and instability; they also greatly Q4 limit the application of bio-oil particularly as transportation fuel. Hydrocarbons derived from biomass are most attractive because of their high energy density and compatibility with the existing infrastructure. Thus, converting lignocellulose into transportation fuels via catalytic fast pyrolysis has attracted much attention. Many studies related to catalytic fast pyrolysis of biomass have been published. The main challenge of this process is the development of active and stable catalysts that can deal with a large variety of decomposition intermediates from lignocellulose. This review starts with the current understanding of the chemistry in fast pyrolysis of lignocellulose and focuses on the development of catalysts in catalytic fast pyrolysis. Recent progress in the experimental studies on catalytic fast pyrolysis of biomass is also summarized with the emphasis on bio-oil yields and quality.

  8. Biosorption of nanoparticles to heterotrophic wastewater biomass.

    Science.gov (United States)

    Kiser, Mehlika A; Ryu, Hodon; Jang, Hyunyoung; Hristovski, Kiril; Westerhoff, Paul

    2010-07-01

    Sorption to activated sludge is a major removal mechanism for pollutants, including manufactured nanoparticles (NPs), in conventional activated sludge wastewater treatment plants. The objectives of this work were to (1) image sorption of fluorescent NPs to wastewater biomass; (2) quantify and compare biosorption of different types of NPs exposed to wastewater biomass; (3) quantify the effects of natural organic matter (NOM), extracellular polymeric substances (EPS), surfactants, and salt on NP biosorption; and (4) explore how different surface functionalities for fullerenes affect biosorption. Batch sorption isotherm experiments were conducted with activated sludge as sorbent and a total of eight types of NPs as sorbates. Epifluorescence images clearly show the biosorption of fluorescent silica NPs; the greater the concentration of NPs exposed to biomass, the greater the quantity of NPs that biosorb. Furthermore, biosorption removes different types of NPs from water to different extents. Upon exposure to 400 mg/L total suspended solids (TSS) of wastewater biomass, 97% of silver nanoparticles were removed, probably in part by aggregation and sedimentation, whereas biosorption was predominantly responsible for the removal of 88% of aqueous fullerenes, 39% of functionalized silver NPs, 23% of nanoscale titanium dioxide, and 13% of fullerol NPs. Of the NP types investigated, only aq-nC(60) showed a change in the degree of removal when the NP suspension was equilibrated with NOM or when EPS was extracted from the biomass. Further study of carbonaceous NPs showed that different surface functionalities affect biosorption. Thus, the production and transformations in NP surface properties will be key factors in determining their fate in the environment.

  9. Co-utilisation of coal and biomass

    Energy Technology Data Exchange (ETDEWEB)

    Michal Kubacki; Andrew B. Ross; Jenny M. Jones; Alan Williams [University of Leeds, Leeds (United Kingdom). Energy and Resources Research Institute, School of Process

    2007-07-01

    Co-utilisation of coal and biomass for energy production results in pollutant reduction. Most notable is the impact on NOx, SOx, volatile organic compounds (VOC) and polyaromatic hydrocarbons (PAH). The aim of this study is to improve our understanding of the synergy in toxic organic emission reduction from co-firing or co-gasifying coal and biomass. A new technique was developed to study co-pyrolysis, heated wire mesh pyrolysis coupled to a GC-mass-spectrometer via a probe, which can sample at varying heights from the pyrolysing fuel. The results from this technique were compared to more conventional pyrolysis-GC-MS as well as thermogravimetric (TGA) and batch reactor studies. Co-combustion was studied by TGA and by burning briquettes supported on a needle in a methane air flame. A range of coals of varying rank, different biomass, as well as model compounds were used. Results show that non-additive combustion behaviour is not easily explained by studying devolatilisation because of the difficulty in replicating the conditions of temperature profile and residence time experienced by the volatiles. Thus, conflicting behaviour is exhibited depending upon pyrolysis technique. However, the atmosphere during experiments appears to be more important. Non-additive combustion for both powdered and pelletised fuels was seen by TGA and studies in a methane-air burner. The coal ignites and burns at a lower temperature because of the interaction with the biomass volatile combustion region. Thus it is proposed that the reduction in emissions from co-combustion arises from enhanced reaction of the coal volatiles by mixing with biomass volatiles in a hot oxidising atmosphere. 14 refs., 11 figs., 2 tabs.

  10. Characterization and valorization of biomass ashes.

    Science.gov (United States)

    Trivedi, Nikhilesh S; Mandavgane, Sachin A; Mehetre, Sayaji; Kulkarni, Bhaskar D

    2016-10-01

    In India, farming is the primary source of income for many families. Following each harvest, a huge amount of biomass is generated. These are generally discarded as "agrowaste," but recent reports have indicated several beneficial uses for these biomasses and their ashes. However, before the utilization of biomass ashes (BMAs), their chemical and physical properties need to be investigated (characterized) so as to utilize their potential benefit to the fullest. In this paper, eight different biomass ashes (soybean plant ash, mustard plant ash, maize ash, groundnut plant ash, cotton plant ash, wheat plant ash, pigeon peas ash, and groundnut shell ash) were characterized, and their chemical properties are discussed. Surface chemical composition analysis, proximate analysis, and ultimate analysis were performed on all BMA samples, and properties such as porosity, particle density, bulk density, point of zero charge, BET surface area, water-absorption capacity, and bulk parameters such as surface pH and surface charges were determined. BMAs were characterized by SEM and FTIR. The surface areas of biomass ashes vary from 1.9 to 46 m(2)/g, and point of zero charge for all BMAs exceed 9.8, which confirmed the alkaline nature of these samples. Based on the chemical composition, BMAs are categorized into four types (S, C, K, and CK), and their utilization is proposed based on the type. BMAs find applications in agriculture and construction industries; glass, rubber, and zeolite manufacturing; and in adsorption (as a source of silica/zeolites). The paper also discusses the research challenges and opportunities in utilization of BMAs.

  11. Transport and supply logistics of biomass fuels: Vol. 2. Biomass and strategic modelling

    Energy Technology Data Exchange (ETDEWEB)

    Allen, J.; Browne, M.; Cook, A.; Wicks, N.; Palmer, H.; Hunter, A.; Boyd, J.

    1996-10-01

    This document forms part of the United Kingdom Department of Trade and Industry project ''Transport and Logistics of Biomass Fuels'', which aimed to describe the distribution of existing and potential biomass resources in terms of their supply potential for power stations. Fixed areas of supply, or catchments, have been identified on colour maps of Britain showing the distribution of forest fuel, short rotation coppices, and various types of straw and animal slurry, using a specially written strategic modelling program. Adequate supplies of biomass resources are shown to exist in Britain, but siting of power stations to exploit these resources, will depend on transport and economic considerations appropriate at the time of construction. Biomass power stations in the megawatt capacity range could be resourced. (UK)

  12. Gluconic acid from biomass fast pyrolysis oils: specialty chemicals from the thermochemical conversion of biomass.

    Science.gov (United States)

    Santhanaraj, Daniel; Rover, Marjorie R; Resasco, Daniel E; Brown, Robert C; Crossley, Steven

    2014-11-01

    Fast pyrolysis of biomass to produce a bio-oil followed by catalytic upgrading is a widely studied approach for the potential production of fuels from biomass. Because of the complexity of the bio-oil, most upgrading strategies focus on removing oxygen from the entire mixture to produce fuels. Here we report a novel method for the production of the specialty chemical, gluconic acid, from the pyrolysis of biomass. Through a combination of sequential condensation of pyrolysis vapors and water extraction, a solution rich in levoglucosan is obtained that accounts for over 30% of the carbon in the bio-oil produced from red oak. A simple filtration step yields a stream of high-purity levoglucosan. This stream of levoglucosan is then hydrolyzed and partially oxidized to yield gluconic acid with high purity and selectivity. This combination of cost-effective pyrolysis coupled with simple separation and upgrading could enable a variety of new product markets for chemicals from biomass.

  13. Energy generation from biomass with the aid of fuel cells; Energetische Nutzung von Biomasse mit Brennstoffzellenverfahren

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    To provide an opportunity for information exchange at the interface between biomass use for energy generation and developers of fuel cells, the workshop 'Energy generation from biomass with the aid of fuel cells' was held by the Fachagentur Nachwachsende Rohstoffe on 9 and 10 December 1998. The lectures and discussions permit to assess better the opportunities and restraints resulting from the use of biogenous fuel gas in fuel cells. (orig.) [German] Um an der Schnittstelle zwischen der energetischen Nutzung von Biomasse und den Entwicklern von Brennstoffzellen einen Informationsaustausch zu ermoeglichen, wurde am 9. und 10. Dezember 1998 der Workshop 'Energetische Nutzung von Biomasse mit Brennstoffzellenverfahren' von der FNR veranstaltet. Die Vortraege und die Diskussion erlauben eine bessere Einschaetzung der Moeglichkeiten und Restriktionen, die sich bei dem Einsatz von biogenen Brenngasen in Brennstoffzellen ergeben. (orig.)

  14. Physical Properties of Biomass Fuel Briquette from Oil Palm Residues

    African Journals Online (AJOL)

    Physical Properties of Biomass Fuel Briquette from Oil Palm Residues. ... Journal of Applied Sciences and Environmental Management ... Keywords: Palm kernel shell; Mesocarp fibre; Briquette; Biomass solid fuel; proximate analysis.

  15. Biomass-dependent susceptibility to drought in experimental grassland communities.

    Science.gov (United States)

    Wang, Yongfan; Yu, Shixiao; Wang, Jiang

    2007-05-01

    Earlier studies indicated that plant diversity influences community resistance in biomass when ecosystems are exposed to perturbations. This relationship remains controversial, however. Here we constructed grassland communities to test the relationships between species diversity and productivity under control and experimental drought conditions. Species richness was not correlated with biomass either under constant conditions or under drought conditions. However, communities with lower biomass production were more resistant to drought stress than those that were more productive. Our results also showed that ecosystem resistance to drought is a decreasing but nonlinear function of biomass. In contrast, species diversity had little and an equivocal effect on ecosystem resistance. From the results reported here, and the results of several previous studies, we suggest that high biomass systems exhibited a greater biomass reduction in response to drought than low biomass systems did, regardless of the relationship between plant diversity and community biomass production.

  16. Catalytic conversion of nonfood woody biomass solids to organic liquids

    NARCIS (Netherlands)

    Barta, Katalin; Ford, Peter C

    2014-01-01

    CONSPECTUS: This Account outlines recent efforts in our laboratories addressing a fundamental challenge of sustainability chemistry, the effective utilization of biomass for production of chemicals and fuels. Efficient methods for converting renewable biomass solids to chemicals and liquid fuels wou

  17. Catalytic conversion of nonfood woody biomass solids to organic liquids

    NARCIS (Netherlands)

    Barta, Katalin; Ford, Peter C

    CONSPECTUS: This Account outlines recent efforts in our laboratories addressing a fundamental challenge of sustainability chemistry, the effective utilization of biomass for production of chemicals and fuels. Efficient methods for converting renewable biomass solids to chemicals and liquid fuels

  18. Storing, Transporting and Pre-treating of Contaminated Biomass

    OpenAIRE

    Tlustoš, P.

    2014-01-01

    The proposed technology is a unique method evaluating decrease of risk element release into environment while the contaminated biomass is transported, stored and pre-treated. This biomass was produced on phytoextraction plantations for further energetic purposes.

  19. Treatment of biomass to obtain a target chemical

    Science.gov (United States)

    Dunson, Jr., James B.; Tucker, III, Melvin P.; Elander, Richard T.; Hennessey, Susan Marie

    2010-08-24

    Target chemicals were produced using biocatalysts that are able to ferment sugars derived from treated biomass. Sugars were obtained by pretreating biomass under conditions of high solids and low ammonia concentration, followed by saccharification.

  20. [Applications of GIS in biomass energy source research].

    Science.gov (United States)

    Su, Xian-Ming; Wang, Wu-Kui; Li, Yi-Wei; Sun, Wen-Xiang; Shi, Hai; Zhang, Da-Hong

    2010-03-01

    Biomass resources have the characteristics of widespread and dispersed distribution, which have close relations to the environment, climate, soil, and land use, etc. Geographic information system (GIS) has the functions of spatial analysis and the flexibility of integrating with other application models and algorithms, being of predominance to the biomass energy source research. This paper summarized the researches on the GIS applications in biomass energy source research, with the focus in the feasibility study of bioenergy development, assessment of biomass resources amount and distribution, layout of biomass exploitation and utilization, evaluation of gaseous emission from biomass burning, and biomass energy information system. Three perspectives of GIS applications in biomass energy source research were proposed, i. e., to enrich the data source, to improve the capacity on data processing and decision-support, and to generate the online proposal.

  1. Combined biomass inventory in the scope of REDD (Reducing ...

    African Journals Online (AJOL)

    Combined biomass inventory in the scope of REDD (Reducing Emissions from Deforestation and Forest Degradation) ... This paper presents an approach for combined biomass inventories in the scope of future REDD regimes ... Article Metrics.

  2. 76 FR 20624 - Oglethorpe Power Corporation: Proposed Biomass Power Plant

    Science.gov (United States)

    2011-04-13

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF AGRICULTURE Rural Utilities Service Oglethorpe Power Corporation: Proposed Biomass Power Plant AGENCY: Rural... Corporation (Oglethorpe) for the construction of a 100 megawatt (MW) biomass plant and related...

  3. An Experimental Investigation of Hydrogen Production from Biomass

    Institute of Scientific and Technical Information of China (English)

    吕鹏梅; 常杰; 付严; 王铁军; 陈勇; 祝京旭

    2003-01-01

    In gaseous products of biomass steam gasification, there exist a lot of CO, CH4 and other hydrocarbons that can be converted to hydrogen through steam reforming reactions. There exists potential hydrogen production from the raw gas of biomass steam gasification. In the present work, the characteristics of hydrogen production from biomass steam gasification were investigated in a small-scale fluidized bed. In these experiments, the gasifying agent (air) was supplied into the reactor from the bottom of the reactor and the steam was added into the reactor above biomass feeding location. The effects of reaction temperature, steam to biomass ratio, equivalence ratio (ER) and biomass particle size on hydrogen yield and hydrogen yield potential were investigated. The experimental results showed that higher reactor temperature, proper ER, proper steam to biomass ratio and smaller biomass particle size will contribute to more hydrogen and potential hydrogen yield.

  4. Integrated strategic and tactical biomass-biofuel supply chain optimization.

    Science.gov (United States)

    Lin, Tao; Rodríguez, Luis F; Shastri, Yogendra N; Hansen, Alan C; Ting, K C

    2014-03-01

    To ensure effective biomass feedstock provision for large-scale biofuel production, an integrated biomass supply chain optimization model was developed to minimize annual biomass-ethanol production costs by optimizing both strategic and tactical planning decisions simultaneously. The mixed integer linear programming model optimizes the activities range from biomass harvesting, packing, in-field transportation, stacking, transportation, preprocessing, and storage, to ethanol production and distribution. The numbers, locations, and capacities of facilities as well as biomass and ethanol distribution patterns are key strategic decisions; while biomass production, delivery, and operating schedules and inventory monitoring are key tactical decisions. The model was implemented to study Miscanthus-ethanol supply chain in Illinois. The base case results showed unit Miscanthus-ethanol production costs were $0.72L(-1) of ethanol. Biorefinery related costs accounts for 62% of the total costs, followed by biomass procurement costs. Sensitivity analysis showed that a 50% reduction in biomass yield would increase unit production costs by 11%.

  5. Pretreatments to enhance the digestibility of lignocellulosic biomass

    NARCIS (Netherlands)

    Hendriks, A.T.W.M.; Zeeman, G.

    2009-01-01

    Lignocellulosic biomass represents a rather unused source for biogas and ethanol production. Many factors, like lignin content, crystallinity of cellulose, and particle size, limit the digestibility of the hemicellulose and cellulose present in the lignocellulosic biomass. Pretreatments have as a

  6. The Biomass mission: a step forward in quantifying forest biomass and structure

    Science.gov (United States)

    LE Toan, T.

    2015-12-01

    The primary aim of the ESA BIOMASS mission is to determine, for the first time and in a consistent manner, the global distribution of above-ground forest biomass (AGB) in order to provide greatly improved quantification of the size and distribution of the terrestrial carbon pool, and improved estimates of terrestrial carbon fluxes. Specifically, BIOMASS will measure forest carbon stock, as well as forest height, from data provided by a single satellite giving a biomass map covering tropical, temperate and boreal forests at a resolution of around 200 m every 6 months throughout the five years of the mission. BIOMASS will use a long wavelength SAR (P-band) providing three mutually supporting measurement techniques, namely polarimetric SAR (PolSAR), polarimetric interferometric SAR (PolInSAR) and tomographic SAR (TomoSAR). The combination of these techniques will significantly reduce the uncertainties in biomass retrievals by yielding complementary information on biomass properties. Horizontal mapping: For a forest canopy, the P-band radar waves penetrate deep into the canopy, and their interaction with the structure of the forest will be exploited to map above ground biomass (AGB), as demonstrated from airborne data for temperate, boreal forests and tropical forest. Height mapping: By repeat revisits to the same location, the PolInSAR measurements will be used to estimate the height of scattering in the forest canopy. The long wavelength used by BIOMASS is crucial for the temporal coherence to be preserved over much longer timescales than at L-band, for example. 3D mapping: The P-band frequency used by BIOMASS is low enough to ensure penetration through the entire canopy, even in dense tropical forests. As a consequence, resolution of the vertical structure of the forest will be possible using tomographic methods from the multi-baseline acquisitions. This is the concept of SAR tomography, which will be implemented in the BIOMASS mission. The improvement in the

  7. Indian Farmers’ Perceptions and Willingness to Supply Surplus Biomass to an Envisioned Biomass-Based Power Plant

    Directory of Open Access Journals (Sweden)

    Anas Zyadin

    2015-04-01

    Full Text Available The main objectives of this socio-technical study are to investigate the Indian farmers’ biomass production capacities and their perceptions and willingness to supply their surplus biomass to fuel an envisioned biomass-based power plant in three selected Indian states: Maharashtra, Madhya Pradesh and Tamil Nadu. For doing so, 471 farmers (about one-third from each state have been interviewed in the field with info-sheet filled in by the field investigators. The farmers from all of the states appeared very much willing to sell their surplus biomass directly to a power plant. The farmers seem to depreciate the involvement of a middleman in the biomass procurement process. The farmers, however, appeared to highly appreciate a community-based association to regulate the biomass prices, with varying perceptions regarding government intervention. The majority of the farmers perceived the establishment of a biomass-based power plant in their region with positive economic outcomes. The farmers identified several barriers to supply biomass to a power plant where transportation logistics appeared to be the main barrier. The study recommends considering biomass collection, storage and transportation logistics as a fundamental segment of any envisioned investment in a biomass-based power plant. Biomass processing, such as pelletization or briquetting is recommended for efficient transportation of biomass at longer distances to reduce the transportation costs. The study further encourages the establishment of a farmers’ association aimed at collecting and selling biomass in agriculture areas predominant for small land holdings.

  8. Biomass supply chain management in North Carolina (part 2: biomass feedstock logistical optimization

    Directory of Open Access Journals (Sweden)

    Kevin Caffrey

    2016-03-01

    Full Text Available Biomass logistics operations account for a major portion of the feedstock cost of running a biorefinery, and make up a significant portion of total system operational costs. Biomass is a bulky perishable commodity that is required in large quantities year round for optimal biorefinery operations. As a proof of concept for a decision making tool for biomass production and delivery, a heuristic was developed to determine biorefinery location, considering city size, agricultural density, and regional demographics. Switchgrass and sorghum (with winter canola were selected to examine as viable biomass feedstocks based on positive economic results determined using a predictive model for cropland conversion potential. Biomass harvest systems were evaluated to examine interrelationships of biomass logistical networks and the least cost production system, with results demonstrating a need to shift to maximize supply-driven production harvest operations and limit storage requirements. For this supply-driven production harvest operations approach a harvest window from September until March was selected for producing big square bales of switchgrass for storage until use, forage chopped sorghum from September to December, and forage chopped switchgrass from December to March. A case study of the three major regions of North Carolina (Mountains, Piedmont, and Coastal Plain was used to assess logistical optimization of the proposed supply-driven production harvest system. Potential biomass production fields were determined within a hundred mile radius of the proposed biorefinery location, with individual fields designated for crop and harvest system by lowest transportation cost. From these selected fields, crops and harvest system regional storage locations were determined using an alternate location-allocation heuristic with set storage capacity per site. Model results showed that the supply-driven production harvest system greatly reduced system complexity

  9. LCA from Biomass Powerplants: from Soil to Electricity

    OpenAIRE

    2013-01-01

    International audience; Biomass is one of the most promising renewable energy. The sustainability of biomass to energy chains needs to be assessed from the soil, including forest management, to the biomass valorization process. A strategy is presented to model the whole life cycle inventory of power production from biomass (beech). The forest growth, management and the wood valorization chain (including pulp, timber, etc., and energy) are modeled by a dedicated platform (called "CAPSIS"). It ...

  10. [Aboveground biomass of three conifers in Qianyanzhou plantation].

    Science.gov (United States)

    Li, Xuanran; Liu, Qijing; Chen, Yongrui; Hu, Lile; Yang, Fengting

    2006-08-01

    In this paper, the regressive models of the aboveground biomass of Pinus elliottii, P. massoniana and Cunninghamia lanceolata in Qianyanzhou of subtropical China were established, and the regression analysis on the dry weight of leaf biomass and total biomass against branch diameter (d), branch length (L), d3 and d2L was conducted with linear, power and exponent functions. Power equation with single parameter (d) was proved to be better than the rests for P. massoniana and C. lanceolata, and linear equation with parameter (d3) was better for P. elliottii. The canopy biomass was derived by the regression equations for all branches. These equations were also used to fit the relationships of total tree biomass, branch biomass and foliage biomass with tree diameter at breast height (D), tree height (H), D3 and D2H, respectively. D2H was found to be the best parameter for estimating total biomass. For foliage-and branch biomass, both parameters and equation forms showed some differences among species. Correlations were highly significant (P biomass, with the highest for total biomass. By these equations, the aboveground biomass and its allocation were estimated, with the aboveground biomass of P. massoniana, P. elliottii, and C. lanceolata forests being 83.6, 72. 1 and 59 t x hm(-2), respectively, and more stem biomass than foliage-and branch biomass. According to the previous studies, the underground biomass of these three forests was estimated to be 10.44, 9.42 and 11.48 t x hm(-2), and the amount of fixed carbon was 47.94, 45.14 and 37.52 t x hm(-2), respectively.

  11. Integration of alternative feedstreams for biomass treatment and utilization

    Science.gov (United States)

    Hennessey, Susan Marie [Avondale, PA; Friend, Julie [Claymont, DE; Dunson, Jr., James B.; Tucker, III, Melvin P.; Elander, Richard T [Evergreen, CO; Hames, Bonnie [Westminster, CO

    2011-03-22

    The present invention provides a method for treating biomass composed of integrated feedstocks to produce fermentable sugars. One aspect of the methods described herein includes a pretreatment step wherein biomass is integrated with an alternative feedstream and the resulting integrated feedstock, at relatively high concentrations, is treated with a low concentration of ammonia relative to the dry weight of biomass. In another aspect, a high solids concentration of pretreated biomass is integrated with an alternative feedstream for saccharifiaction.

  12. Potential evaluation of biomass-based energy sources for Turkey

    OpenAIRE

    Mustafa Ozcan; Semra Öztürk; Yuksel Oguz

    2015-01-01

    Turkey has great potential with respect to renewable energy sources (RES) and, among such sources, “biomass energy” is of particular importance. The purpose of this study is to determine the primary electrical energy potential obtainable from the biomass potential, according to different biomass source types. In this study, the biomass sources of municipal solid wastes, energy crops, animal manure and urban wastewater treatment sludge are evaluated. For each source, individual biogas and biom...

  13. Is torrefaction of polysaccharides-rich biomass equivalent to carbonization of lignin-rich biomass?

    Science.gov (United States)

    Bilgic, E; Yaman, S; Haykiri-Acma, H; Kucukbayrak, S

    2016-01-01

    Waste biomass species such as lignin-rich hazelnut shell (HS) and polysaccharides-rich sunflower seed shell (SSS) were subjected to torrefaction at 300°C and carbonization at 600°C under nitrogen. The structural variations in torrefied and carbonized biomasses were compared. Also, the burning characteristics under dry air and pure oxygen (oxy-combustion) conditions were investigated. It was concluded that the effects of carbonization on HS are almost comparable with the effects of torrefaction on SSS in terms of devolatilization and deoxygenation potentials and the increases in carbon content and the heating value. Consequently, it can be proposed that torrefaction does not provide efficient devolatilization from the lignin-rich biomass while it is relatively more efficient for polysaccharides-rich biomass. Heat-induced variations in biomass led to significant changes in the burning characteristics under both burning conditions. That is, low temperature reactivity of biomass reduced considerably and the burning shifted to higher temperatures with very high burning rates.

  14. Torrefied biomass for use in power station sector; Torrefizierte Biomasse zum Einsatz im Kraftwerkssektor

    Energy Technology Data Exchange (ETDEWEB)

    Witt, Janet; Schaubach, Kay [Deutsches Biomasseforschungszentrum (DBFZ) gemeinnuetzige GmbH, Leipzig (Germany). Bereich Bioenergiesysteme; Kiel, Jaap; Carbo, Michiel [Energy Research Centre of the Netherlands (ECN), Petten (Netherlands); Wojcik, Magdalena [OFI Austrian Research Institute for Chemistry and Technology, Vienna (Austria)

    2013-10-01

    In the torrefaction process biomass is heated up in the absence of oxygen to a temperature of at least 250 C. By combining torrefaction with pelletisation or briquetting, biomass materials can be converted into a high-energy-density bioenergy carrier with improved behaviour in (long-distance) transport, handling and storage. Torrefaction also creates superior properties for biomass in many major end-use applications. The process has the potential to provide a significant contribution to an enlarged raw material portfolio for sustainable biomass fuel production inside Europe by including both agricultural and forestry biomass (residues). The article will briefly introduce the concept and objectives of the project and the different torrefaction technologies involved and then focus on the results obtained within the first project phase of the EU-project SECTOR. This comprises production of torrefied biomass batches, subsequent densification (pelletisation and briquetting), characterisation and Round Robin testing of characterisation methods, initial logistics and end-use performance testing, material safety data sheet preparation and sustainability assessment along the value chain. (orig.)

  15. Feasibility of Biomass Biodrying for Gasification Process

    Science.gov (United States)

    Hamidian, Arash

    An important challenge of biomass gasification is the limitation of feedstock quality especially the moisture content, which plays a significant role on the performance of gasification process. Gasification requires low moisture levels (20% and less) and several reports have emphasized on the moisture as a typical problem while gasifying biomass. Moisture affects overall reaction rates in the gasifiers as a result of temperature drop and ultimately increases tar content, decreases gas yield, changes the composition of produced gas and affects the efficiency. Therefore, it is mandatory to pre-treat the biomass before gasification and reduce the moisture content to the suitable and economic level. The well-known solutions are either natural drying (not practical for commercial plants) or conventional drying technologies (have high operating costs). Biodrying is an alternative process, which uses both convective air and heat of biological reactions as a source of energy, to reduce the moisture. In the biodrying reactor heat is generated from exothermic decomposition of organic fraction of biomass and that is why the process is called "self-heating process". Employing such technology for drying biomass at pre-treatment units of gasification process returns several economic and environmental advantages to mills. In Europe, municipal waste treatment (MSW) plants use the biodrying at commercial scale to degrade a part of the biodegradable fraction of waste to generate heat and reduce the moisture content for high quality SRF (Solid Recovered Fuel) production. In Italy, wine industry is seeking to develop biodrying for energy recovery of grape wastes after fermentation and distillation, which returns economic benefits to the industry. In Canada, the development of biodrying technology for pulp and paper industry was started at Ecole polytechnique de Montreal as an option for sludge management solution. Therefore, batch biodrying reactor was successfully developed in 2004

  16. Biomass energy in the making; La biomasse: une energie en devenir

    Energy Technology Data Exchange (ETDEWEB)

    Anon

    2008-07-01

    Wood, straw, agricultural residues, organic wastes, biomass is everywhere you look. But the efficient use of this source of green electricity - the world's second largest renewable energy source - requires optimization of biomass collection and combustion processes. Biomass is back on the political agenda. In mid-June of this year, the French government gave this renewable energy a boost by selecting twenty-two projects to generate power and heat with biomass. The plants, to be commissioned by 2010, will be located in eleven different regions and will consume energy from organic plant matter. The power generated will be bought at a firm price of 128 euros per megawatt-hour. Most of the fuel will come from forest and paper industry waste, but straw and even grape pomace will be used in some cases. The plants will have a combined generating capacity of 300 MWh, raising France's installed biomass capacity to a total of 700 MWe. A drop of water in the ocean in the overall scheme of France's electricity. It is true that France has long neglected biomass. In 2004, electricity generated from biological resources represented a mere 1.74 TWhe in France, just 0.3% of its power consumption. This will rise to 0.6% once the new plants have come on line. The trend is the same in all of the EU's 27 member states, according to Eurostat, the statistical office of the European Communities: the amount of electricity generated from biomass (including biogas, municipal waste and wood) has practically doubled in six years, rising from 40 to 80 TWhe between 2000 and 2005. This is an improvement, but it still only represents 2.5% of the electricity supplied to Europeans. On a global scale, biomass contributes just 1% of total electric power generation. Yet biomass is an energy resource found all over the world, whether as agricultural waste, wood chips, or dried treatment plant sludge, to name but a few. Biomass power plants have managed to gain a foothold mainly in

  17. Plant biomass in the Tanana River Basin, Alaska.

    Science.gov (United States)

    Bert R. Mead

    1995-01-01

    Vegetation biomass tables are presented for the Tanana River basin. Average biomass for each species of tree, shrub, grass, forb, lichen, and moss in the 13 forest and 30 nonforest vegetation types is shown. These data combined with area estimates for each vegetation type provide a tool for estimating habitat carrying capacity for many wildlife species. Tree biomass is...

  18. Materials Problems and Solutions in Biomass Fired Plants

    DEFF Research Database (Denmark)

    Larsen, Ole Hede; Montgomery, Melanie

    2006-01-01

    Due to Denmark’s pledge to reduce carbon dioxide emissions, biomass is utilised increasingly as a fuel for generating energy. Extensive research and demonstration projects especially in the area of material performance for biomass fired boilers have been undertaken to make biomass a viable fuel...

  19. Process and apparatus for the conversion of biomass

    NARCIS (Netherlands)

    Bakker, R.R.C.; Hazewinkel, J.H.O.; Groenestijn, van J.W.

    2008-01-01

    The invention is directed to a process for the conversion of cellulosic biomass, in particular lignocellulose-containing biomass into fermentable sugars. The invention is further directed to apparatus suitable for carrying out such processes. According to the invention biomass is converted into ferm

  20. Reinforcement effect of biomass carbon and protein in elastic biocomposites

    Science.gov (United States)

    Biomass carbon and soy protein were used to reinforce natural rubber biocomposites. The particle size of biomass carbon were reduced and characterized with elemental analysis, x-ray diffraction, infrared spectroscopy, and particle size analysis. The rubber composite reinforced with the biomass carbo...

  1. Allometric models for estimating biomass and carbon in Alnus acuminata

    Directory of Open Access Journals (Sweden)

    William Fonseca

    2013-12-01

    Full Text Available In order to quantify the climate change mitigation potential of forest plantations, information on total biomass and its growth rate is required. Depending on the method used, the study of the biomass behavior can be a complex and expensive activity. The main objective of this research was to develop allometric models to estimate biomass for different tree components (leaves, branches, stem and root and total tree biomass in Alnus acuminata (Kunth in Costa Rica. Additionally, models were developed to estimate biomass and carbon in trees per hectare and for total plant biomass per hectare (trees + herbaceous vegetation + necromass. To construct the tree models, 41 sampling plots were evaluated in seven sites from which 47 trees with a diametric from 4.5 to 44.5 cm were selected to be harvested. In the selected models for the stem, root and total tree biomass, a r 2 >93.87 % was accomplished, while the r 2aj for leaves and branches was 88 %. For the biomass and carbon models for total trees and total plant biomass per hectare the r2 was >99 %. Average biomass expansion factor was 1.22 for aboveground and 1.43 for total biomass (when the root was included. The carbon fraction in plant biomass varied between 32.9 and 46.7 % and the percentage of soil carbon was 3 %.

  2. High-temperature entrained flow gasification of biomass

    DEFF Research Database (Denmark)

    Qin, Ke; Lin, Weigang; Jensen, Peter Arendt

    2012-01-01

    Biomass (wood and straw) gasification has been studied in a laboratory scale atmospheric pressure entrained flow reactor. Effects of reaction temperature, steam/carbon molar ratio, excess air ratio, and biomass type on the solid, liquid and gas products were investigated. The biomass was completely...

  3. 75 FR 56525 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2010-09-16

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Biomass... meeting of the Biomass Research and Development Technical Advisory Committee under Section 9008(d) of the... participation. This notice announces the meeting of the Biomass Research and Development Technical...

  4. 77 FR 6791 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2012-02-09

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Biomass... Biomass Research and Development Technical Advisory Committee. The Federal Advisory Committee Act requires... production of biobased fuels and biobased products. Tentative Agenda Update on USDA Biomass R&D...

  5. 78 FR 44105 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2013-07-23

    ... Efficiency and Renewable Energy Biomass Research and Development Technical Advisory Committee AGENCY: Energy... announces an open meeting of the Biomass Research and Development Technical Advisory Committee. The Federal... contact (Departments of Energy and Agriculture) with respect to the Biomass R&D Initiative...

  6. 75 FR 74026 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2010-11-30

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Biomass... meeting of the Biomass Research and Development Technical Advisory Committee under Section 9008(d) of the... meeting of the Biomass Research and Development Technical Advisory Committee. DATES: December 15, 2010...

  7. 76 FR 22091 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2011-04-20

    ... Efficiency and Renewable Energy Biomass Research and Development Technical Advisory Committee AGENCY: Energy... announces an open meeting of the Biomass Research and Development Technical Advisory Committee. The Federal... products. Tentative Agenda: Agenda will include the following: Update on USDA Biomass R&D Activities...

  8. 77 FR 64970 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2012-10-24

    ... Office of Energy Efficiency and Renewable Energy Biomass Research and Development Technical Advisory... open meeting. SUMMARY: This notice announces an open meeting of the Biomass Research and Development... and biobased products. Tentative Agenda: Agenda will include the following: Update on USDA Biomass...

  9. 75 FR 30804 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2010-06-02

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Biomass... meeting of the Biomass Research and Development Technical Advisory Committee under Section 9008(d) of the... participation. This notice announces the meeting of the Biomass Research and Development Technical...

  10. 77 FR 42298 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2012-07-18

    ... Efficiency and Renewable Energy Biomass Research and Development Technical Advisory Committee AGENCY: Energy... Appointment as a Member of the Biomass Research and Development Technical Advisory Committee. SUMMARY: In... soliciting nominations for candidates to fill vacancies on the Biomass Research and Development...

  11. 78 FR 29125 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2013-05-17

    ... of Energy Efficiency and Renewable Energy Biomass Research and Development Technical Advisory... open meeting. SUMMARY: This notice announces an open meeting of the Biomass Research and Development... ] Energy and Agriculture) with respect to the Biomass R&D Initiative (Initiative) and also makes...

  12. 77 FR 20377 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2012-04-04

    ... of Energy Efficiency and Renewable Energy Biomass Research and Development Technical Advisory... Open Webinar. SUMMARY: This notice announces an open webinar of the Biomass Research and Development..., members of the public are welcome to observe the business of the Biomass Research and...

  13. 75 FR 11526 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2010-03-11

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Biomass... meeting of the Biomass Research and Development Technical Advisory Committee under Section 9008(d) of the... participation. This notice announces the meeting of the Biomass Research and Development Technical...

  14. 77 FR 26276 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2012-05-03

    ... Efficiency and Renewable Energy Biomass Research and Development Technical Advisory Committee AGENCY: Energy... announces an open meeting of the Biomass Research and Development Technical Advisory Committee. The Federal... products. Tentative Agenda: Agenda will include the following: Update on USDA Biomass R&D Activities...

  15. 78 FR 64932 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2013-10-30

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Biomass... Biomass Research and Development Technical Advisory Committee under Section 9008(d) of the Food.... This notice announces the meeting of the Biomass Research and Development Technical Advisory...

  16. 76 FR 56949 - Biomass Crop Assistance Program; Corrections

    Science.gov (United States)

    2011-09-15

    ... Corporation 7 CFR Part 1450 RIN 0560-AI13 Biomass Crop Assistance Program; Corrections AGENCY: Commodity... Commodity Credit Corporation (CCC) is amending the Biomass Crop Assistance Program (BCAP) regulation to..., storage and transportation (CHST) of existing sources of biomass. The limited funding available for...

  17. 78 FR 8500 - Biomass Research and Development Technical Advisory Committee

    Science.gov (United States)

    2013-02-06

    ... of Energy Efficiency and Renewable Energy Biomass Research and Development Technical Advisory... Open Meeting. SUMMARY: This notice announces an open meeting of the Biomass Research and Development.... Tentative Agenda: Agenda will include the following: Update on USDA Biomass R&D Activities Update on...

  18. Process and apparatus for the conversion of biomass

    NARCIS (Netherlands)

    Bakker, R.R.C.; Hazewinkel, J.H.O.; Groenestijn, van J.W.

    2008-01-01

    The invention is directed to a process for the conversion of cellulosic biomass, in particular lignocellulose-containing biomass into fermentable sugars. The invention is further directed to apparatus suitable for carrying out such processes. According to the invention biomass is converted into

  19. EUBIONET III - Solutions to biomass trade and market barriers

    NARCIS (Netherlands)

    Alakangas, E.; Junginger, H.M.; Dam, J.M.C. van; Hinge, J.; Keränen, J.; Olsson, O.; Porsö, C.; Martikainen, A.; Rathbauer, J.; Sulzenbacher, L.; Vesterinen, P.; Vinterbäck, J.

    2012-01-01

    The EUBIONET III project has boosted (i) sustainable, transparent international biomass fuel trade, (ii) investments in best practice technologies and (iii) new services on biomass heat sector. Furthermore, it identified cost-efficient and value-adding use of biomass for energy and industry. The aim

  20. Regional biomass stores and dynamics in forests of coastal Alaska

    Science.gov (United States)

    Mikhaill A. Yatskov; Mark E. Harmon; Olga N. Krankina; Tara M. Barrett; Kevin R. Dobelbower; Andrew N. Gray; Becky Fasth; Lori Trummer; Toni L. Hoyman; Chana M. Dudoit

    2015-01-01

    Coastal Alaska is a vast forested region (6.2 million ha) with the potential to store large amounts of carbon in live and dead biomass thus influencing continental and global carbon dynamics. The main objectives of this study were to assess regional biomass stores, examine the biomass partitioning between live and dead pools, and evaluate the effect of disturbance on...

  1. Evaluation of sampling strategies to estimate crown biomass

    Science.gov (United States)

    Krishna P Poudel; Hailemariam Temesgen; Andrew N Gray

    2015-01-01

    Depending on tree and site characteristics crown biomass accounts for a significant portion of the total aboveground biomass in the tree. Crown biomass estimation is useful for different purposes including evaluating the economic feasibility of crown utilization for energy production or forest products, fuel load assessments and fire management strategies, and wildfire...

  2. Biotrade1: international trade in renewable energy from biomass

    NARCIS (Netherlands)

    Agterberg, A.E.; Faaij, A.P.C.

    2006-01-01

    This paper discusses international trade in renewable energy from biomass. Main objective is to compare options for international trade in energy from biomass and to compare these options with non-trade options like domestic use of biomass and afforestation. Aspects that are taken into account are c

  3. Biotrade1: international trade in renewable energy from biomass

    NARCIS (Netherlands)

    Agterberg, A.E.; Faaij, A.P.C.

    1998-01-01

    This paper discusses international trade in renewable energy from biomass. Main objective is to compare options for international trade in energy from biomass and to compare these options with non-trade options like domestic use of biomass and afforestation. Aspects that are taken into account are

  4. Biomass burning fuel consumption rates: a field measurement database

    CSIR Research Space (South Africa)

    Van Leeuwen, TT

    2014-01-01

    Full Text Available Landscape fires show large variability in the amount of biomass or fuel consumed per unit area burned. These fuel consumption (FC) rates depend on the biomass available to burn and the fraction of the biomass that is actually combusted, and can...

  5. ROOT BIOMASS ALLOCATION IN THE WORLD'S UPLAND FORESTS

    Science.gov (United States)

    Because the world's forests play a major role in regulating nutrient and carbon cycles, there is much interest in estimating their biomass. Estimates of aboveground biomass based on well-established methods are relatively abundant; estimates of root biomass based on standard meth...

  6. Biomass power for rural development. Revised design report.

    Energy Technology Data Exchange (ETDEWEB)

    Neuhauser, Edward

    1999-10-03

    The retrofit of Dunkirk Steam Station to fire biomass fuels is an important part of the Consortium's goal--demonstrating the viability of commercial scale willow energy crop production and conversion to power. The goal for th biomass facilities at Dunkirk is to reliably cofire a combination of wood wastes and willow biomass with coal at approximately 20% by heat input.

  7. Biomass thermochemical gasification: Experimental studies and modeling

    Science.gov (United States)

    Kumar, Ajay

    The overall goals of this research were to study the biomass thermochemical gasification using experimental and modeling techniques, and to evaluate the cost of industrial gas production and combined heat and power generation. This dissertation includes an extensive review of progresses in biomass thermochemical gasification. Product gases from biomass gasification can be converted to biopower, biofuels and chemicals. However, for its viable commercial applications, the study summarizes the technical challenges in the gasification and downstream processing of product gas. Corn stover and dried distillers grains with solubles (DDGS), a non-fermentable byproduct of ethanol production, were used as the biomass feedstocks. One of the objectives was to determine selected physical and chemical properties of corn stover related to thermochemical conversion. The parameters of the reaction kinetics for weight loss were obtained. The next objective was to investigate the effects of temperature, steam to biomass ratio and equivalence ratio on gas composition and efficiencies. DDGS gasification was performed on a lab-scale fluidized-bed gasifier with steam and air as fluidizing and oxidizing agents. Increasing the temperature resulted in increases in hydrogen and methane contents and efficiencies. A model was developed to simulate the performance of a lab-scale gasifier using Aspen Plus(TM) software. Mass balance, energy balance and minimization of Gibbs free energy were applied for the gasification to determine the product gas composition. The final objective was to optimize the process by maximizing the net energy efficiency, and to estimate the cost of industrial gas, and combined heat and power (CHP) at a biomass feedrate of 2000 kg/h. The selling price of gas was estimated to be 11.49/GJ for corn stover, and 13.08/GJ for DDGS. For CHP generation, the electrical and net efficiencies were 37 and 86%, respectively for corn stover, and 34 and 78%, respectively for DDGS. For

  8. Biomass Resource Assessment and Existing Biomass Use in the Madhya Pradesh, Maharashtra, and Tamil Nadu States of India

    Directory of Open Access Journals (Sweden)

    Karthikeyan Natarajan

    2015-05-01

    Full Text Available India is experiencing energy crisis and a widening gap between energy supply and demand. The country is, however, endowed with considerable, commercially and technically available renewable resources, from which surplus agro-biomass is of great importance and a relatively untapped resource. In the policy making process, knowledge of existing biomass use, degree of social reliance, and degree of biomass availability for energy production is unequivocal and pre-conditional. Field observations, documentation, and fill-in sheet tools were used to investigate the potential of biomass resources and the existing domestic, commercial, and industrial uses of biomass in selected Indian states. To do so, a team of field observers/supervisors visited three Indian states namely: Maharashtra (MH, Madhya Pradesh (MP, and Tamil Nadu (TN. Two districts from each state were selected to collect data regarding the use of biomass and the extent of biomass availability for energy production. In total, 471 farmers were interviewed, and approximately 75 farmers with various land holdings have been interviewed in each district. The existing uses of biomass have been documented in this survey study and the results show that the majority of biomass is used as fodder for domestic livestock followed by in-site ploughing, leaving trivial surplus quantities for other productive uses. Biomass for cooking appeared to be insignificant due to the availability and access to Liquefied Petroleum Gas (LPG cylinders in the surveyed districts. Opportunities exist to utilize roadside-dumped biomass, in-site burnt biomass, and a share of biomass used for ploughing. The GIS-based maps show that biomass availability varies considerably across the Taluks of the surveyed districts, and is highly dependent on a number of enviromental and socio-cultural factors. Developing competitive bioenergy market and enhancing and promoting access to more LPG fuel connections seem an appropriate socio

  9. Modeling biomass gasification in circulating fluidized beds

    Science.gov (United States)

    Miao, Qi

    In this thesis, the modeling of biomass gasification in circulating fluidized beds was studied. The hydrodynamics of a circulating fluidized bed operating on biomass particles were first investigated, both experimentally and numerically. Then a comprehensive mathematical model was presented to predict the overall performance of a 1.2 MWe biomass gasification and power generation plant. A sensitivity analysis was conducted to test its response to several gasifier operating conditions. The model was validated using the experimental results obtained from the plant and two other circulating fluidized bed biomass gasifiers (CFBBGs). Finally, an ASPEN PLUS simulation model of biomass gasification was presented based on minimization of the Gibbs free energy of the reaction system at chemical equilibrium. Hydrodynamics plays a crucial role in defining the performance of gas-solid circulating fluidized beds (CFBs). A 2-dimensional mathematical model was developed considering the hydrodynamic behavior of CFB gasifiers. In the modeling, the CFB riser was divided into two regions: a dense region at the bottom and a dilute region at the top of the riser. Kunii and Levenspiel (1991)'s model was adopted to express the vertical solids distribution with some other assumptions. Radial distributions of bed voidage were taken into account in the upper zone by using Zhang et al. (1991)'s correlation. For model validation purposes, a cold model CFB was employed, in which sawdust was transported with air as the fluidizing agent. A comprehensive mathematical model was developed to predict the overall performance of a 1.2 MWe biomass gasification and power generation demonstration plant in China. Hydrodynamics as well as chemical reaction kinetics were considered. The fluidized bed riser was divided into two distinct sections: (a) a dense region at the bottom of the bed where biomass undergoes mainly heterogeneous reactions and (b) a dilute region at the top where most of homogeneous

  10. Biomass Conversion over Heteropoly Acid Catalysts

    KAUST Repository

    Zhang, Jizhe

    2015-04-01

    Biomass is a natural resource that is both abundant and sustainable. Its efficient utilization has long been the focus of research and development efforts with the aim to substitute it for fossil-based feedstock. In addition to the production of biofuels (e.g., ethanol) from biomass, which has been to some degree successful, its conversion to high value-added chemicals is equally important. Among various biomass conversion pathways, catalytic conversion is usually preferred, as it provides a cost-effective and eco-benign route to the desired products with high selectivities. The research of this thesis is focused on the conversion of biomass to various chemicals of commercial interest by selective catalytic oxidation. Molecular oxygen is chosen as the oxidant considering its low cost and environment friendly features in comparison with commonly used hydrogen peroxide. However, the activation of molecular oxygen usually requires high reaction temperatures, leading to over oxidation and thus lower selectivities. Therefore, it is highly desirable to develop effective catalysts for such conversion systems. We use kegging-type heteropoly acids (HPAs) as a platform for catalysts design because of their high catalytic activities and ease of medication. Using HPA catalysts allows the conversion taking place at relatively low temperature, which is beneficial to saving production cost as well as to improving the reaction selectivity. The strong acidity of HPA promotes the hydrolysis of biomass of giant molecules (e.g. cellulose), which is the first as well as the most difficult step in the conversion process. Under certain circumstances, a HPA combines the merits of homogeneous and heterogeneous catalysts, acting as an efficient homogeneous catalyst during the reaction while being easily separated as a heterogeneous catalyst after the reaction. We have successfully applied HPAs in several biomass conversion systems. Specially, we prepared a HPA-based bi-functional catalyst

  11. Biomass energy systems information user study

    Energy Technology Data Exchange (ETDEWEB)

    Belew, W.W.; Wood, B.L.; Marle, T.L.; Reinhardt, C.L.

    1981-02-01

    The results of a series of telephone interviews with groups of users of information on biomass energy systems are described. These results, part of a larger study on many different solar technologies, identify types of information each group needed and the best ways to get information to each group. This report is 1 of 10 discussing study results. The overall study provides baseline data about information needs in the solar community. Results from 12 biomass groups of respondents are analyzed in this report: Federally Funded Researchers (2 groups), Nonfederally Funded Researchers (2 groups), Representatives of Manufacturers (2 groups), Representatives of State Forestry Offices, Private Foresters, Forest Products Engineers, Educators, Cooperative Extension Service County Agents, and System Managers. The data will be used as input to the determination of information products and services the Solar Energy Research Institute, the Solar Energy Information Data Bank Network, and the entire information outreach community should be preparing and disseminating.

  12. Lignin biomass conversion into chemicals and fuels

    DEFF Research Database (Denmark)

    Melián Rodríguez, Mayra

    % of the weight and 40% of the energy content of lignocellulosic biomass. While designated applications for cellulose already exist in form of the current pulp and paper production as well as its prospective hydrolysis and fermentation into biofuels (mainly bioethanol), sustainable ways to valorize the lignin...... fraction of wood are yet to be established, due to its poor solubility and complex heterogeneous structure. This constitutes a major drawback in the economic viability of a biorefinery, where complete valorization of lignocellulosic biomass is necessary. For this reason, and due to its potential...... as a valuable feedstock for the production of organic chemicals, lignin valorization has become an important issue to solve. For a better understanding and analysis of the catalytic performance of lignin, it is common to use lignin model compounds, which contain the most significant linkages present in lignin...

  13. Biomass integrated CFB gasification combined cycle plants

    Energy Technology Data Exchange (ETDEWEB)

    Greil, C.; Hirschfelder, H. (Lurgi Umwelt GmbH, Frankfurt am Main (Germany))

    1998-01-01

    This paper presents an overview on the Lurgi-Circulating Fluidized Bed technology (CFB). CFB units are state of the art and have proven their capability of converting biomass, waste or coal into power and/or steam. CFB reactors are in commercial operation for reduction processes and for combustion and gasification of solid fuels. In this paper reduction processes are not considered. The fact, that world-wide over 80 CFB combustion plants using Lurgi technology are commercially operating proves that this technology is well accepted. Lurgi's CFB gasification technology is at present applied in two industrial plants. It is the key process for the advanced biomass or waste utilisation plants. The paper focuses on CFB fuel gas production for combined cycle plants (IGCC) and for cofiring into existing boiler plants. 5 refs., 4 figs.

  14. Fuel gas from biomass - utilisation concepts

    Energy Technology Data Exchange (ETDEWEB)

    Greil, C.; Vierrath, H. [Lurgi Envirotherm GmbH, Frankfurt am Main (Germany)

    2000-07-01

    This paper presents an overview on the Lurgi-Circulating Fluidized Bed technology (CFB). CFB units are state of the art and have proven their capability of converting biomass, waste of coal into power and/or steam. CFB reactors are in commercial operation for reduction processes and for combustion and gasification of solid fuels. In this paper reduction processes are not considered. The fact, that world-wide over 80 CFB combustion plants using Lurgi technology are commercially operating proves that this technology is well accepted. Lurgi's CFB gasification technology is at present applied in two industrial plants. It is the key process for our advanced biomass or waste utilisation plants. The subject paper will focus on CFB fuel gas production for combined cycle plants (IGCC) and for co-firing into existing boiler plants. (orig.)

  15. Biomass integrated CFB gasification combined cycle plants

    Energy Technology Data Exchange (ETDEWEB)

    Greil, C.; Hirschfelder, H. [Lurgi Umwelt GmbH, Frankfurt am Main (Germany)

    1998-12-31

    This paper presents an overview on the Lurgi-Circulating Fluidized Bed technology (CFB). CFB units are state of the art and have proven their capability of converting biomass, waste or coal into power and/or steam. CFB reactors are in commercial operation for reduction processes and for combustion and gasification of solid fuels. In this paper reduction processes are not considered. The fact, that world-wide over 80 CFB combustion plants using Lurgi technology are commercially operating proves that this technology is well accepted. Lurgi`s CFB gasification technology is at present applied in two industrial plants. It is the key process for the advanced biomass or waste utilisation plants. The paper focuses on CFB fuel gas production for combined cycle plants (IGCC) and for cofiring into existing boiler plants. 5 refs., 4 figs.

  16. Torrefaction of biomass for power production

    DEFF Research Database (Denmark)

    Saleh, Suriyati Binti

    . Straw can be co-fired with coal in suspension fired power plants with a maximum straw share of 10 to 20 wt%. However, 100% straw firing induced several problems that can impede both boiler availability and power efficiency. Straw is highly fibrous and tenacious in nature, therefore a relatively high...... rates, relatively low superheater temperatures have to be applied, which in turn lower the power efficiency. The idea for this Ph.D. project is to develop a biomass pretreatment method that could provide the heating value of the fuel for the boiler, but in a way such that the fuel is easily pulverized...... wheat straw, miscanthus, spruce, beech, pine, and spruce bark) with different chemical and physical properties were pyrolyzed by Simultaneous Thermal Analysis (STA) and torrefied in the simultaneous torrefaction and grinding reactor. The effect of biomass alkali content on torrefaction characteristics...

  17. Bounding biomass in the Fisher equation

    Science.gov (United States)

    Birch, Daniel A.; Tsang, Yue-Kin; Young, William R.

    2007-06-01

    The Fisher-Kolmogorov-Petrovskii-Piskunov equation with a variable growth rate and advection by an incompressible velocity field is considered as a model for plankton dispersed by ocean currents. If the average growth rate is negative then the model has a survival-extinction transition; the location of this transition in the parameter space is constrained using variational arguments and delimited by simulations. The statistical steady state reached when the system is in the survival region of parameter space is characterized by integral constraints and upper and lower bounds on the biomass and productivity that follow from variational arguments and direct inequalities. In the limit of zero-decorrelation time the velocity field is shown to act as Fickian diffusion with an eddy diffusivity much larger than the molecular diffusivity: this allows a one-dimensional model to predict the biomass, productivity, and extinction transitions. All results are illustrated with a simple growth and stirring model.

  18. Determination of kinetic parameters for biomass combustion.

    Science.gov (United States)

    Álvarez, A; Pizarro, C; García, R; Bueno, J L; Lavín, A G

    2016-09-01

    The aim of this work is to provide a wide database of kinetic data for the most common biomass by thermogravimetric analysis (TGA) and differential thermogravimetry (DTG). Due to the characteristic parameters of DTG curves, a two-stage reaction model is proposed and the kinetic parameters obtained from model-based methods with energy activation values for first and second stages in the range 1.75·10(4)-1.55·10(5)J/mol and 1.62·10(4)-2.37·10(5)J/mol, respectively. However, it has been found that Flynn-Wall-Ozawa and Kissinger-Akahira-Sunose model-free methods are not suitable to determine the kinetic parameters of biomass combustion since the assumptions of these two methods were not accomplished in the full range of the combustion process.

  19. LEVULINIC ACID PRODUCTION FROM WASTE BIOMASS

    Directory of Open Access Journals (Sweden)

    Anna Maria Raspolli Galletti,

    2012-02-01

    Full Text Available The hydrothermal conversion of waste biomass to levulinic acid was investigated in the presence of homogeneous acid catalysts. Different cheap raw materials (poplar sawdust, paper mill sludge, tobacco chops, wheat straw, olive tree pruning were employed as substrates. The yields of levulinic acid were improved by optimization of the main reaction parameters, such as type and amount of acid catalyst, temperature, duration, biomass concentration, and electrolyte addition. The catalytic performances were also improved by the adoption of microwave irradiation as an efficient heating method, allowing significant energy and time savings. The hydrothermal conversions of inulin and wheat straw were carried out in the presence of niobium phosphate, which up to now have never been employed in these reactions. The preliminary results appeared to be in need of further optimization.

  20. Bioremoval of heavy metals by bacterial biomass.

    Science.gov (United States)

    Aryal, Mahendra; Liakopoulou-Kyriakides, Maria

    2015-01-01

    Heavy metals are among the most common pollutants found in the environment. Health problems due to the heavy metal pollution become a major concern throughout the world, and therefore, various treatment technologies such as reverse osmosis, ion exchange, solvent extraction, chemical precipitation, and adsorption are adopted to reduce or eliminate their concentration in the environment. Biosorption is a cost-effective and environmental friendly technique, and it can be used for detoxification of heavy metals in industrial effluents as an alternative treatment technology. Biosorption characteristics of various bacterial species are reviewed here with respect to the results reported so far. The role of physical, chemical, and biological modification of bacterial cells for heavy metal removal is presented. The paper evaluates the different kinetic, equilibrium, and thermodynamic models used in bacterial sorption of heavy metals. Biomass characterization and sorption mechanisms as well as elution of metal ions and regeneration of biomass are also discussed.