Estimated quantities of residual materials in a KBS-3H repository at Olkiluoto

International Nuclear Information System (INIS)

Hagros, Annika

2008-12-01

The quantities of residual materials in a KBS-3H type repository have been estimated in this report. The repository is assumed to be constructed at Olkiluoto in Eurajoki, Western Finland. Both the total quantities of the materials introduced into the repository and the quantities of materials that remain in the repository after closure have been calculated. The calculations are largely based on a similar work regarding the material quantities in the Finnish KBS-3V repository and the main goal has been to identify the differences between the KBS-3H and KBS-3V repositories with respect to the type and quantities of residual materials. As the design of the KBS-3H repository is not final yet, the results are only preliminary. Several alternative designs were assumed in the calculations, resulting in different total quantities of materials. The design alternatives that had the greatest effect on the total material quantities were the two different tunnel backfill options, bentonite-crushed rock and Friedland clay. If Friedland clay is used instead of a bentonite-crushed rock mixture, the total quantity of pyrite remaining in the repository is 20 times larger and the quantities of organic materials and gypsum are also increased significantly. The other design alternatives did not have a substantial effect on the total material quantities. The remaining quantity of cement can be reduced by some 20% by selecting the silica grouting alternative in the sealing of the rock mass and low-pH cement in the shotcreting of the repository, instead of using the ordinary cement alternatives. If the total quantity of steel should be minimised, the use of the DAWE design alternative would be better than the Basic Design, although the total reduction would be less than 10%. The main difference between the different drift end plug alternatives is related to the total remaining quantity of silica, which is some 80% smaller if the rock plug is used instead of the LHHP (Low Heat High

40Ar/39Ar age spectra from the KBS Tuff, Koobi Fora Formation

International Nuclear Information System (INIS)

McDougall, I.

1981-01-01

40 Ar/ 39 Ar age spectra on anorthoclase phenocrysts from three pumice clasts in the KBS Tuff yield nearly ideal flat patterns, providing good evidence that the samples have remained undisturbed since crystallization. The ages are concordant at 1.88 = 0.02 Myr, and confirm that the KBS Tuff, a key marker bed in the Koobi Fora Formation, northern Kenya, is now very well dated. These results resolve the conflict between earlier 40 Ar/ 39 Ar and conventional K-Ar dating measurements on the KBS Tuff. (author)

40Ar/39Ar age spectra from the KBS Tuff, Koobi Fora Formation.

Science.gov (United States)

McDougall, Ian

1981-11-12

40 Ar/ 39 Ar age spectra on anorthoclase phenocrysts from three pumice clasts in the KBS Tuff yield nearly ideal flat patterns, providing good evidence that the samples have remained undisturbed since crystallization. The ages are concordant at 1.88±0.02 Myr, and confirm that the KBS Tuff, a key marker bed in the Koobi Fora Formation, northern Kenya, is now very well dated. These results resolve the conflict between earlier 40 Ar/ 39 Ar and conventional K-Ar dating measurements on the KBS Tuff.

Spent nuclear fuel for disposal in the KBS-3 repository

Energy Technology Data Exchange (ETDEWEB)

Grahn, Per; Moren, Lena; Wiborgh, Maria

2010-12-15

The report is included in a set of Production reports, presenting how the KBS-3 repository is designed, produced and inspected. The set of reports is included in the safety report for the KBS-3 repository and repository facility. The report provides input to the assessment of the long-term safety, SR-Site as well as to the operational safety report, SR-Operation. The report presents the spent fuel to be deposited, and the requirements on the handling and selection of fuel assemblies for encapsulation that follows from that it shall be deposited in the KBS-3 repository. An overview of the handling and a simulation of the encapsulation and the resulting canisters to be deposited are presented. Finally, the initial state of the encapsulated spent nuclear fuel is given. The initial state comprises the radionuclide inventory and other data required for the assessment of the long-term safety

Spent nuclear fuel for disposal in the KBS-3 repository

International Nuclear Information System (INIS)

Grahn, Per; Moren, Lena; Wiborgh, Maria

2010-12-01

The report is included in a set of Production reports, presenting how the KBS-3 repository is designed, produced and inspected. The set of reports is included in the safety report for the KBS-3 repository and repository facility. The report provides input to the assessment of the long-term safety, SR-Site as well as to the operational safety report, SR-Operation. The report presents the spent fuel to be deposited, and the requirements on the handling and selection of fuel assemblies for encapsulation that follows from that it shall be deposited in the KBS-3 repository. An overview of the handling and a simulation of the encapsulation and the resulting canisters to be deposited are presented. Finally, the initial state of the encapsulated spent nuclear fuel is given. The initial state comprises the radionuclide inventory and other data required for the assessment of the long-term safety

Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Complementary evaluations of safety

International Nuclear Information System (INIS)

Neall, Fiona; Pastina, Barbara; Snellman, Margit; Smith, Paul; Gribi, P.; Johnson, Lawrence

2008-12-01

The KBS-3H design is a variant of the more general KBS-3 method for the geological disposal of spent nuclear fuel in Finland and Sweden. In the KBS-3H design, multiple assemblies containing spent fuel are emplaced horizontally in parallel, approximately 300 m long, slightly inclined deposition drifts. The copper canisters, each with a surrounding layer of bentonite clay, are placed in perforated steel shells prior to deposition in the drifts; the assembly is called the 'supercontainer'. The other KBS-3 variant is the KBS-3V design, in which the copper canisters are emplaced vertically in individual deposition holes surrounded by bentonite clay but without steel supercontainer shells. SKB and Posiva have conducted a Research, Development and Demonstration programme over the period 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to KBS-3V. As part of this programme, the long-term safety of a KBS-3H repository has been assessed in the KBS-3H safety studies. In order to focus the safety studies, the Olkiluoto site in the municipality of Eurajoki, which is the proposed site for a spent fuel repository in Finland, was used as a hypothetical site for a KBS-3H repository. The present report is part of a portfolio of reports discussing the long-term safety of the KBS-3H repository. The overall outcome of the KBS-3H safety studies is documented in the summary report, 'Safety assessment for a KBS-3H repository for spent nuclear fuel at Olkiluoto'. The purpose and scope of the KBS-3H complementary evaluations of safety report is provided in Posiva's Safety Case Plan, which is based on Regulatory Guide YVL 8.4 and on international guidelines on complementary lines of argument to long-term safety that are considered an important element of a post-closure safety case for geological repositories. Complementary evaluations of safety require the use of evaluations, evidence and qualitative supporting arguments that lie outside the

Gravitational biology on the space station

Science.gov (United States)

Keefe, J. R.; Krikorian, A. D.

1983-01-01

The current status of gravitational biology is summarized, future areas of required basic research in earth-based and spaceflight projects are presented, and potential applications of gravitational biology on a space station are demonstrated. Topics covered include vertebrate reproduction, prenatal/postnatal development, a review of plant space experiments, the facilities needed for growing plants, gravimorphogenesis, thigmomorphogenesis, centrifuges, maintaining a vivarium, tissue culture, and artificial human organ generation. It is proposed that space stations carrying out these types of long-term research be called the National Space Research Facility.

KBS Annual Report 1982. Summaries of technical reports issued during 1982

International Nuclear Information System (INIS)

1983-07-01

The purpose of the KBS Annual Report is to inform interested organizations and individuals of the research and development work perfomed by the division KBS within the Swedish Nuclear Fuel Supply Co. (SKBF) on the handling, treatment and final storage of nuclear wastes in Sweden. In the Annual Report for 1982 the summaries of 27 technical reports and other publications issued during the year are listed. (K.A.E.)

Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Complementary evaluations of safety

Energy Technology Data Exchange (ETDEWEB)

Neall, Fiona; Pastina, Barbara; Snellman, Margit; Smith, Paul; Gribi, P.; Johnson, Lawrence

2008-12-15

The KBS-3H design is a variant of the more general KBS-3 method for the geological disposal of spent nuclear fuel in Finland and Sweden. In the KBS-3H design, multiple assemblies containing spent fuel are emplaced horizontally in parallel, approximately 300 m long, slightly inclined deposition drifts. The copper canisters, each with a surrounding layer of bentonite clay, are placed in perforated steel shells prior to deposition in the drifts; the assembly is called the 'supercontainer'. The other KBS-3 variant is the KBS-3V design, in which the copper canisters are emplaced vertically in individual deposition holes surrounded by bentonite clay but without steel supercontainer shells. SKB and Posiva have conducted a Research, Development and Demonstration programme over the period 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to KBS-3V. As part of this programme, the long-term safety of a KBS-3H repository has been assessed in the KBS-3H safety studies. In order to focus the safety studies, the Olkiluoto site in the municipality of Eurajoki, which is the proposed site for a spent fuel repository in Finland, was used as a hypothetical site for a KBS-3H repository. The present report is part of a portfolio of reports discussing the long-term safety of the KBS-3H repository. The overall outcome of the KBS-3H safety studies is documented in the summary report, 'Safety assessment for a KBS-3H repository for spent nuclear fuel at Olkiluoto'. The purpose and scope of the KBS-3H complementary evaluations of safety report is provided in Posiva's Safety Case Plan, which is based on Regulatory Guide YVL 8.4 and on international guidelines on complementary lines of argument to long-term safety that are considered an important element of a post-closure safety case for geological repositories. Complementary evaluations of safety require the use of evaluations, evidence and qualitative supporting arguments

Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Evolution report

International Nuclear Information System (INIS)

Smith, P.; Johnson, L.; Snellman, M.; Pastina, B.; Gribi, P.

2007-12-01

The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 method. Posiva and SKB have conducted a joint research, demonstration and development (RD and D) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007, have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. In the KBS-3H design alternative, each canister, with a surrounding layer of bentonite clay, is pre-packaged in a perforated steel cylinder prior to emplacement in the deposition drift; the entire assembly is called the supercontainer. Several supercontainers are positioned along parallel, 100 - 300 m long deposition drifts, which are sealed following waste emplacement using drift end plugs. Bentonite distance blocks separate the supercontainers, one from another, along the drift. Steel compartment plugs can be used to seal off drift sections with higher inflow, thus isolating the different compartments within the drift. The present report describes the repository evolution in successive time frames, including key uncertainties. The description of evolution starts with the initial conditions at the time of emplacement of the first canisters. The repository evolves through an early, transient phase to a state where evolution is far slower. Particular attention is given to describing the transient phase, since this is where most of the

Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Evolution report

International Nuclear Information System (INIS)

Smith, Paul; Johnson, Lawrence; Snellman, Margit; Pastina, Barbara; Gribi, Peter

2008-01-01

The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 method. Posiva and SKB have conducted a joint research, demonstration and development (RDandD) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007, have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. In the KBS-3H design alternative, each canister, with a surrounding layer of bentonite clay, is pre-packaged in a perforated steel cylinder prior to emplacement in the deposition drift; the entire assembly is called the supercontainer. Several supercontainers are positioned along parallel, 100-300 m long deposition drifts, which are sealed following waste emplacement using drift end plugs. Bentonite distance blocks separate the supercontainers, one from another, along the drift. Steel compartment plugs can be used to seal off drift sections with higher inflow, thus isolating the different compartments within the drift. The present report describes the repository evolution in successive time frames, including key uncertainties. The description of evolution starts with the initial conditions at the time of emplacement of the first canisters. The repository evolves through an early, transient phase to a state where evolution is far slower. Particular attention is given to describing the transient phase, since this is where most of the

Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Evolution report

Energy Technology Data Exchange (ETDEWEB)

Smith, Paul; Johnson, Lawrence; Snellman, Margit; Pastina, Barbara; Gribi, Peter

2008-01-15

The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 method. Posiva and SKB have conducted a joint research, demonstration and development (RDandD) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007, have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. In the KBS-3H design alternative, each canister, with a surrounding layer of bentonite clay, is pre-packaged in a perforated steel cylinder prior to emplacement in the deposition drift; the entire assembly is called the supercontainer. Several supercontainers are positioned along parallel, 100-300 m long deposition drifts, which are sealed following waste emplacement using drift end plugs. Bentonite distance blocks separate the supercontainers, one from another, along the drift. Steel compartment plugs can be used to seal off drift sections with higher inflow, thus isolating the different compartments within the drift. The present report describes the repository evolution in successive time frames, including key uncertainties. The description of evolution starts with the initial conditions at the time of emplacement of the first canisters. The repository evolves through an early, transient phase to a state where evolution is far slower. Particular attention is given to describing the transient phase, since this is where most of the

Modelling of Fracture Initiation, Propagation and Creep of a KBS-3V and KBS-3H Repository in Sparsely Fractured Rock with Application to the Design at Forsmark Candidate Site

International Nuclear Information System (INIS)

Backers, Tobias; Stephansson, Ove

2008-01-01

The stability issues of deposition holes of a repository layout according to the KBS-3 concept in the sparsely fractured Forsmark granites are analysed with the emphasis on fracture mechanics. At the start of the project the rock mass is viewed as a continuum. In a second step explicit fracture networks are introduced and included in the numerical rock fracture models. The software Fracod2D was used for the rock fracture mechanics analysis. Assuming deposition holes located in a continuous, homogeneous elastic rock mass and The presented stress state of the rock mass the following results were obtained: For single KBS-3H deposition holes oriented in the direction of the minimum horizontal stress, Sh, bore hole breakouts are introduced for all depth levels. For KBS-3H holes which are oriented in direction of SH, no significant fracturing can be expected. In case of vertical deposition holes according to KBS-3V an increased risk of fracturing at greater depth levels (> 500m) is evident. At shallow depth levels ( 5MPa gives a favourable situation about spalling for the KBS-3H and KBS-3V layouts. To prevent spalling, it is important to build up a swelling pressure soon after excavation, so that the enhanced stresses in the surrounding of the deposition ii holes are reduced. This has a positive impact on other excavation activities and also on time-dependent fracturing. After excavation and filling of the deposition holes with subsequent increase of swelling pressure, the temperature will increase in the vicinity of the excavation. For the range of swelling pressures predicted for the KBS-3 concept, i.e. 5.5MPa to 7.2MPa, no significant fracturing for the KBS-3H concept with the axis parallel SH at depths below about 600m was discovered. The results from other layouts bare the risk of partly significant fracturing. About 60ka from closing the repository an ice cover of approximately 3km is expected over Forsmark. This dead load increases the in-situ stresses and

Evaluation of SKB/Posiva's report on the horizontal alternative of the KBS-3 method

International Nuclear Information System (INIS)

Apted, Michael J.; Bennet, David G.; Saario, Timtetr; Savage, David

2009-10-01

The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. The method has two design alternatives: the vertical (KBS-3V) and the horizontal (KBS-3H). In the KBS-3H concept, copper canisters loaded with spen nuclear fuel are encased in a compacted bentonite buffer with an outer supporting supercontainer composed of a mild steel basket, and the entire supercontainer is emplaced horizontally in long emplacement drifts. SKB and Posiva have conducted a joint research, development and demonstration (RDandD) programme in 2002-2007 with the overall aim of establishing whether the KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The objectives have been to demonstrate that the horizontal deposition alternative is technically feasible and that it fulfils the same long-term safety requirement as the KBS-3V. Swedish Radiation Safety Authority (SSM) considers that it is a proper time to evaluate the work carried by SKB and Posiva when this period of joint research is ended and a relatively complete set of reporting is available. SSM therefore required its external expert group BRITE (the Barrier Review, Integration, Tracking and Evaluation) to evaluate the reporting. The aims of the evaluation are to investigate the differences between the horizontal and vertical design alternatives with respect to: Completeness: has SKB/Posiva identified the full set of key topics, and if not, what additional specific key topics should be evaluated; Depth-of-treatment: has SKB/Posiva analysed the key topics in sufficient depth, and if not, on what specific aspects in more detailed consideration required; Status of information: has SKB/ Posiva provided enough information on the current status of knowledge and uncertainties that impact the understanding of each key topic, and if not, what further information should be cited; Feasibility and practicality: for key issues related to the fabrication and

Meddling in the KBS Programme and Swedish Success in Nuclear Waste Management

Energy Technology Data Exchange (ETDEWEB)

Elam, Mark (Univ. of Goeteborg, Goeteborg (Sweden)), e-mail: mark.elam@sts.gu.se; Sundqvist, Goeran (Univ. of Oslo, Oslo (Norway))

2010-09-15

In this paper the intention is to analyse and re/describe the qualities that underlie the current fame and good standing of Swedish nuclear waste management (the so-called KBS Programme). Inspired by work in the actor-network theory tradition, we want to argue that the success of the KBS Programme can be best accounted for with reference to qualities which are the reverse of those you might otherwise expect. While you might imagine its good name to be ascribable to the constancy, solidity and singularity of the solution being advanced, we want to argue that it is rather the infidelity, fluidity and heterogeneity of this solution that can best account for the leading position of Swedish nuclear waste management today. In fact, we wish to assert that it is through the effacement of the inherent importance of the latter set of qualities, that the KBS Programme has been able to promote a vision of itself as successfully imbued with the former set. The enduring template for Swedish nuclear waste management was established in 1977 through the Nuclear Stipulation Act. This gave rise to the cultivation of a new expertise within the Swedish nuclear industry of demonstrating indubitable solutions to nuclear waste problems close at hand. Thus, while it may appear that the KBS Programme has always been about the conception, and step by step implementation of a completely coherent and largely unvarying approach to the geological disposal of nuclear waste, this can be seen as effacing another reality. Bringing this other reality back into view, we see that for the KBS Programme, attaining the goal of the geological disposal of nuclear waste has never been as important as maintaining the ability to demonstrate its attainability. The KBS Programme is firstly a long-running programme in the material semiotics of nuclear fuel safety and the production of palpable signs of the accomplishment of geological disposal close at hand. This production of palpable signs has extended to the

Meddling in the KBS Programme and Swedish Success in Nuclear Waste Management

International Nuclear Information System (INIS)

Elam, Mark; Sundqvist, Goeran

2010-09-01

In this paper the intention is to analyse and re/describe the qualities that underlie the current fame and good standing of Swedish nuclear waste management (the so-called KBS Programme). Inspired by work in the actor-network theory tradition, we want to argue that the success of the KBS Programme can be best accounted for with reference to qualities which are the reverse of those you might otherwise expect. While you might imagine its good name to be ascribable to the constancy, solidity and singularity of the solution being advanced, we want to argue that it is rather the infidelity, fluidity and heterogeneity of this solution that can best account for the leading position of Swedish nuclear waste management today. In fact, we wish to assert that it is through the effacement of the inherent importance of the latter set of qualities, that the KBS Programme has been able to promote a vision of itself as successfully imbued with the former set. The enduring template for Swedish nuclear waste management was established in 1977 through the Nuclear Stipulation Act. This gave rise to the cultivation of a new expertise within the Swedish nuclear industry of demonstrating indubitable solutions to nuclear waste problems close at hand. Thus, while it may appear that the KBS Programme has always been about the conception, and step by step implementation of a completely coherent and largely unvarying approach to the geological disposal of nuclear waste, this can be seen as effacing another reality. Bringing this other reality back into view, we see that for the KBS Programme, attaining the goal of the geological disposal of nuclear waste has never been as important as maintaining the ability to demonstrate its attainability. The KBS Programme is firstly a long-running programme in the material semiotics of nuclear fuel safety and the production of palpable signs of the accomplishment of geological disposal close at hand. This production of palpable signs has extended to the

Biosphere analysis for selected cases in TILA-99 and in KBS-3H safety evaluation 2007

International Nuclear Information System (INIS)

Broed, R.; Avila, R.; Bergstroem, U.; Hjerpe, T.; Ikonen, A.

2008-12-01

The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 spent fuel disposal method. Posiva and SKB have conducted a joint research, demonstration and development (RD and D) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007 have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. This report summarises the biosphere analysis conducted in the KBS-3H safety studies. The most important components of the analysis are presented in this report: i) predictions of the physical terrain and the ecosystems possibly receiving contaminant releases from the repository, ii) modelling of the transport of radionuclides in the entire landscape, taking into account that the ecosystems currently present at the site will evolve over time, and, iii) the estimation of potential doses to humans. The main outcome from the present analysis, dealing with radiological safety and compliance with regulatory requirements, is the annual landscape dose, which is related to individuals fully utilising the maximum production of food and water from the potentially contaminated area. In order to facilitate comparisons with earlier assessments, resulting release rates into the biosphere, from both KBS-3H and TILA-99 calculation cases, were used as inputs for the biosphere analysis. The present study shows that none of the

Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Process report

Energy Technology Data Exchange (ETDEWEB)

Gribi, Peter; Johnson, Lawrence; Suter, Daniel; Smith, Paul; Pastina, Barbara; Snellman, Margit

2008-01-15

The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 spent fuel disposal method. Posiva and SKB have conducted a joint research, demonstration and development (RDandD) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007 have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. In the KBS-3H design alternative, each canister, with a surrounding layer of bentonite clay, is placed in a perforated steel cylinder prior to emplacement; the entire assembly is called the supercontainer. Several supercontainers are positioned along parallel, 100-300 m long deposition drifts, which are sealed following waste emplacement using drift end plugs. Bentonite distance blocks separate the supercontainers, one from another, along the drift. Steel compartment plugs can be used to seal off drift sections with higher inflow, thus isolating the different compartments within the drift. The present report describes the main processes potentially affecting the long-term safety of the system, covering radiation-related, thermal, hydraulic, mechanical, chemical (including microbiological) and radionuclide transport-related processes. The process descriptions deal sequentially with the main sub-systems: fuel/cavity in canister, cast iron insert and copper canister, buffer and other bentonite components, supercontainer

Safety assessment for a KBS-3H spent nuclear fuel repository at Olkiluoto. Process report

International Nuclear Information System (INIS)

Gribi, Peter; Johnson, Lawrence; Suter, Daniel; Smith, Paul; Pastina, Barbara; Snellman, Margit

2008-01-01

The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. KBS-3H and KBS-3V are the two design alternatives of the KBS-3 spent fuel disposal method. Posiva and SKB have conducted a joint research, demonstration and development (RDandD) programme in 2002-2007 with the overall aim of establishing whether KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The overall objectives of the present phase covering the period 2004-2007 have been to demonstrate that the horizontal deposition alternative is technically feasible and to demonstrate that it fulfils the same long-term safety requirements as KBS-3V. The safety studies conducted as part of this programme include a safety assessment of a preliminary design of a KBS-3H repository for spent nuclear fuel located about 400 m underground at the Olkiluoto site, which is the proposed site for a spent fuel repository in Finland. In the KBS-3H design alternative, each canister, with a surrounding layer of bentonite clay, is placed in a perforated steel cylinder prior to emplacement; the entire assembly is called the supercontainer. Several supercontainers are positioned along parallel, 100-300 m long deposition drifts, which are sealed following waste emplacement using drift end plugs. Bentonite distance blocks separate the supercontainers, one from another, along the drift. Steel compartment plugs can be used to seal off drift sections with higher inflow, thus isolating the different compartments within the drift. The present report describes the main processes potentially affecting the long-term safety of the system, covering radiation-related, thermal, hydraulic, mechanical, chemical (including microbiological) and radionuclide transport-related processes. The process descriptions deal sequentially with the main sub-systems: fuel/cavity in canister, cast iron insert and copper canister, buffer and other bentonite components, supercontainer

A low-delay 8 Kb/s backward-adaptive CELP coder

Science.gov (United States)

Neumeyer, L. G.; Leblanc, W. P.; Mahmoud, S. A.

1990-01-01

Code excited linear prediction coding is an efficient technique for compressing speech sequences. Communications quality of speech can be obtained at bit rates below 8 Kb/s. However, relatively large coding delays are necessary to buffer the input speech in order to perform the LPC analysis. A low delay 8 Kb/s CELP coder is introduced in which the short term predictor is based on past synthesized speech. A new distortion measure that improves the tracking of the formant filter is discussed. Formal listening tests showed that the performance of the backward adaptive coder is almost as good as the conventional CELP coder.

K-Ar age estimate for the KBS Tuff, East Turkana, Kenya

International Nuclear Information System (INIS)

McDougall, I.; Maier, R.; Sutherland-Hawkes, P.; Gleadow, A.J.W.

1980-01-01

Stone tools and numerous vertebrate fossils including hominids, have been found in close stratigraphic proximity to the KBS Tuff, whose age has been the subject of much debate. Concordant K-Ar ages, averaging 1.89 +- 0.01 Myr, are reported on anorthoclase phenocrysts from 13 pumice clasts collected from within the KBS Tuff or its correlatives. It is believed that this age is the best estimate currently available for the time of formation of this important marker horizon within the East Turkana Basin. (author)

The KBS concepts - General outline, present study

International Nuclear Information System (INIS)

Pusch, R.

1980-01-01

The Swedish KBS 2 concept, which concerns spent, unreprocessed reactor fuel, implies the use of an 'engineered' barrier of highly compacted Na bentonite for isolating metal canisters with the wastes from the surrounding rock. The isolating power of a barrier of this kind will be so great that it will probably be suggested for other radioactive wastes as well

Evaluation of SKB/Posiva's report on the horizontal alternative of the KBS-3 method

Energy Technology Data Exchange (ETDEWEB)

Apted, Michael J.; Bennet, David G.; Saario, Timtetr; Savage, David

2009-10-15

The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. The method has two design alternatives: the vertical (KBS-3V) and the horizontal (KBS-3H). In the KBS-3H concept, copper canisters loaded with spen nuclear fuel are encased in a compacted bentonite buffer with an outer supporting supercontainer composed of a mild steel basket, and the entire supercontainer is emplaced horizontally in long emplacement drifts. SKB and Posiva have conducted a joint research, development and demonstration (RDandD) programme in 2002-2007 with the overall aim of establishing whether the KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The objectives have been to demonstrate that the horizontal deposition alternative is technically feasible and that it fulfils the same long-term safety requirement as the KBS-3V. Swedish Radiation Safety Authority (SSM) considers that it is a proper time to evaluate the work carried by SKB and Posiva when this period of joint research is ended and a relatively complete set of reporting is available. SSM therefore required its external expert group BRITE (the Barrier Review, Integration, Tracking and Evaluation) to evaluate the reporting. The aims of the evaluation are to investigate the differences between the horizontal and vertical design alternatives with respect to: Completeness: has SKB/Posiva identified the full set of key topics, and if not, what additional specific key topics should be evaluated; Depth-of-treatment: has SKB/Posiva analysed the key topics in sufficient depth, and if not, on what specific aspects in more detailed consideration required; Status of information: has SKB/ Posiva provided enough information on the current status of knowledge and uncertainties that impact the understanding of each key topic, and if not, what further information should be cited; Feasibility and practicality: for key issues related to the fabrication and

Vitrified radwaste from reprocessing. Supplementary geological investigations of the KBS-project, Sweden

International Nuclear Information System (INIS)

1979-01-01

The Swedish nuclear power utilities' application to load two new reactors, according to the so called Stipulation Act was denied by the Swedish Government i Novermber 1978. According to the Government the utilities' KBS-project had not demonstrated the existence of a large, light rockformation suited for disposal of the radioactive wastes or the spent fuels. In this report an account is given of the futher investigations that were undertaken by the KBS-project to prove that such a rockformation exists at Sternoe in Southern Sweden. (L.E.)

Montmorillonite stability. With special respect to KBS-3 conditions

International Nuclear Information System (INIS)

Karnland, Ola; Birgersson, Martin

2006-08-01

The basic advantageous properties, e.g. low hydraulic conductivity and high swelling pressure, of the bentonite buffer in a KBS- repository stem from a strong interaction between water and the montmorillonite mineral in the bentonite. Minerals similar in structure but with substantially lower mineral-water interaction exist in nature. Transformations from montmorillonite to such minerals are observed e.g. in burial diagenesis and in contact metamorphism. A thermodynamic consideration confirms that medium and low charged montmorillonite is not in chemical equilibrium with quartz. From a safety assessment perspective it is therefore of vital importance to quantify the montmorillonite transformation under KBS- conditions. Silica release from the montmorillonite tetrahedral layers is the initial process for several possible transformations. Replacement of silica by aluminum increases the layer charge but maintains the basic atomic structure. A sufficiently high layer charge results in an irreversible collapse of the clay-water structure, i.e. a non-swelling mineral is formed. Compared to other cations, potassium as counter ion leads to a collapse at lower layer charge and the produced phase is generally termed illite. Montmorillonite-to-illite transformation is the most frequently found alteration process in nature. Three different kinetic illitization models are reviewed and the model proposed by Huang et al. is considered the most suitable for quantification in a KBS- repository, since the kinetic rate expression and its associated parameters are systematically determined by laboratory work. The model takes into account temperature, montmorillonite fraction and potassium concentration, but do not include relevant parameters such as pH, temperature gradients and water content. Calculations by use of the Huang illitization model applied for repository conditions yield insignificant montmorillonite transformation also under very pessimistic assumptions. Other non

Montmorillonite stability. With special respect to KBS-3 conditions

Energy Technology Data Exchange (ETDEWEB)

Karnland, Ola; Birgersson, Martin [Clay Technology AB, Lund (Sweden)

2006-08-15

The basic advantageous properties, e.g. low hydraulic conductivity and high swelling pressure, of the bentonite buffer in a KBS- repository stem from a strong interaction between water and the montmorillonite mineral in the bentonite. Minerals similar in structure but with substantially lower mineral-water interaction exist in nature. Transformations from montmorillonite to such minerals are observed e.g. in burial diagenesis and in contact metamorphism. A thermodynamic consideration confirms that medium and low charged montmorillonite is not in chemical equilibrium with quartz. From a safety assessment perspective it is therefore of vital importance to quantify the montmorillonite transformation under KBS- conditions. Silica release from the montmorillonite tetrahedral layers is the initial process for several possible transformations. Replacement of silica by aluminum increases the layer charge but maintains the basic atomic structure. A sufficiently high layer charge results in an irreversible collapse of the clay-water structure, i.e. a non-swelling mineral is formed. Compared to other cations, potassium as counter ion leads to a collapse at lower layer charge and the produced phase is generally termed illite. Montmorillonite-to-illite transformation is the most frequently found alteration process in nature. Three different kinetic illitization models are reviewed and the model proposed by Huang et al. is considered the most suitable for quantification in a KBS- repository, since the kinetic rate expression and its associated parameters are systematically determined by laboratory work. The model takes into account temperature, montmorillonite fraction and potassium concentration, but do not include relevant parameters such as pH, temperature gradients and water content. Calculations by use of the Huang illitization model applied for repository conditions yield insignificant montmorillonite transformation also under very pessimistic assumptions. Other non

KBS Annual Report 1983. Including summaries of technical reports issued during 1983

International Nuclear Information System (INIS)

1984-06-01

The purpose of the KBS Annual Report is to inform interested organizations and individuals of the research and development work performed by the division KBS within the Swedish Nuclear Fuel Supply Co (SKBF) on the handling, treatment and final storage of nuclear wastes in Sweden. The Annual Report normally contains a presentation of the legal and organizational situation followed by an account of the progress within different areas of the R and D-work. This account also includes indications of the activities planned for the future. At the end of the report the summaries of 76 technical reports and other publications issued during the year are listed in special appendices. (K.A.E.)

Biological field stations: research legacies and sites for serendipity

Science.gov (United States)

William K. Michener; Keith L. Bildstein; Arthur McKee; Robert R. Parmenter; William W. Hargrove; Deedra McClearn; Mark Stromberg

2009-01-01

Biological field stations are distributed throughout North America, capturing much of the ecological variability present at the continental scale and encompassing many unique habitats. In addition to their role in supporting research and education, field stations offer legacies of data, specimens, and accumulated knowledge. Such legacies often provide the only...

PASS - Project on Alternative Systems Study. Performance assessment of bentonite clay barrier in three repository concepts: VDH, KBS-3 and VLH

International Nuclear Information System (INIS)

Pusch, R.; Boergesson, L.

1992-12-01

The three repository concepts VDH, KBS3 and VLH have been investigated with respect to their functions in short- and long-term perspectives. The study shows that while KBS3 does not require development of new techniques for excavation and application of buffers and canisters, such development is needed for VLH and VDH. The various physical processes in the deployment part of VDH are more critical and less understood than those in KBS3 and VLH, but the sealing effect of the plugged 'low-temperature' part is sufficiently good to make the concept qualify as a candidate. VLH has the highest and KBS3 the lowest temperature and the latter has the highest potential for good long-term function. (59 refs.)

Leveraging on Information Technology to Teach Construction Law to Built Environment Students: A Knowledge-Based System (KBS Approach

Directory of Open Access Journals (Sweden)

Faisal Manzoor Arain

2009-11-01

Full Text Available Construction law is a vital component of the body of knowledge that is needed by construction professionals in order to successfully operate in the commercial world of construction. Construction law plays an important role in shaping building projects. Construction projects are complex because they involve many human and non-human factors and variables. Teaching construction law is therefore a complex issue with several dimensions. In recent years, Information Technology (IT has become strongly established as a supporting tool for many professions, including teachers. If faculty members have a knowledge base established on similar past projects, it would assist the faculty members to present case studies and contractually based scenarios to students. This paper proposes potential utilisation of a Knowledge-based System (KBS for teaching construction law to built environment students. The KBS is primarily designed for building professionals to learn from similar past projects. The KBS is able to assist professionals by providing accurate and timelyinformation for decision making and a user-friendly tool for analysing and selecting the suggested controls for variations in educational buildings. It is recommended that the wealth of knowledge available in the KBS can be very helpful in teaching construction law to built environment students. The system presents real case studies and scenarios to students to allow them to analyse and learn construction law. The KBS could be useful to students as a general research tool because the students could populate it with their own data and use it with the reported educational projects. With further generic modifications, the KBS will also be useful for built environment students to learn about project management of building projects; thus, it will raise the overall level of professional understanding, and eventually productivity, in the construction industry.

The effect of the FPI-rule on the suitability of the KBS-3H concept

International Nuclear Information System (INIS)

Pekkarinen, M.

2014-12-01

In the KBS-3H design the spent nuclear fuel canisters are placed in horizontal depositions drifts. In this work the degree of utilization, the number of placed canisters, the number of canisters in critical positions, and other related figures are estimated with Monte Carlo simulations. For comparison, the results are also computed for the KBS-3V design, where the canisters are placed in vertical deposition holes below tunnels. Different FPI criteria are evaluated for their performance in detecting the critical positions, i.e. positions where the super-container of the canister intersects a fracture with diameter over 150 m. Two different canister placement algorithms are considered, and the simulations are run with and without considering modeled site scale fault zones. The simple FPI criterion, where all full perimeter intersections are considered critical, was found overly conservative, leading to low degree of utilization (46-73 %). FPI criteria that require that a fracture is an FPI in multiple drifts are better, although the degree of utilization is still poor at the outskirts of the repository. The number of canisters in critical position is also 2-20 times as large as with the simple criterion. In KBS-3V design the criteria reject a much smaller number of canister positions, because the number of FPIs is smaller. A larger number of canisters are placed in critical position in KBS-3V design, because the FPC cannot detect the large fractures below the tunnels. (orig.)

HMCBG processes related to the steel components in the KBS-3H disposal concept

International Nuclear Information System (INIS)

Johnson, Lawrence; Marschall, Paul; Wersin, Paul; Gribi, Peter

2008-05-01

An analysis of the Hydro-Mechanical-Chemical-microBiological processes affected by Gas (HMCBG) related to the steel components of the KBS-3H disposal concept has been performed. The outcome of this study is foreseen to contribute to the KBS-3H Process Report for a repository for spent fuel sited at Olkiluoto. Three different design options for KBS-3H are currently being studied (open tunnel option, two variants of tight distance block option). While the details of the design may influence the short to medium term performance, it is found that the medium to long-term evolution of KBS-3H is not significantly affected by the chosen design option, provided the distance blocks behave according to design. Under repository conditions, the corrosion of the supercontainer will be fairly rapid. Complete conversion of Fe0 to oxidised Fe 2+ /Fe 3+ species may occur within a few thousands of years. The main corrosion products will be magnetite and, depending on the groundwater composition, also iron sulphide and perhaps siderite. Furthermore, corrosion-derived Fe(II) may react with the clay to form Fe(II)-rich silicates. The supercontainer environment will thus experience a volume change and some loss of plasticity of the buffer between the supercontainer and the rock wall may occur. This might promote bacterial activity at the supercontainer surface, which would lead to an enhancement of localised corrosion and probably to destabilisation of the magnetite layer. Previous investigations indicate, however, that there will be no relevant bacterial activity in the main part of the buffer by virtue of its small pore sizes and low water activity. In the course of time, the swelling pressure of bentonite will be affected by a number of processes, including magnetite formation, geochemical degradation, intrusion of bentonite into void space either initially present or created by relative displacement of distance blocks and supercontainer, and by subsequent bentonite erosion. The

HMCBG processes related to the steel components in the KBS-3H disposal concept

Energy Technology Data Exchange (ETDEWEB)

Johnson, Lawrence; Marschall, Paul; Wersin, Paul (National Cooperative for the Disposal of Radioactive Waste, Nagra, Wettingen (Switzerland)); Gribi, Peter (SandR Consult GmbH, Baden (Switzerland))

2008-05-15

An analysis of the Hydro-Mechanical-Chemical-microBiological processes affected by Gas (HMCBG) related to the steel components of the KBS-3H disposal concept has been performed. The outcome of this study is foreseen to contribute to the KBS-3H Process Report for a repository for spent fuel sited at Olkiluoto. Three different design options for KBS-3H are currently being studied (open tunnel option, two variants of tight distance block option). While the details of the design may influence the short to medium term performance, it is found that the medium to long-term evolution of KBS-3H is not significantly affected by the chosen design option, provided the distance blocks behave according to design. Under repository conditions, the corrosion of the supercontainer will be fairly rapid. Complete conversion of Fe0 to oxidised Fe2+/Fe3+ species may occur within a few thousands of years. The main corrosion products will be magnetite and, depending on the groundwater composition, also iron sulphide and perhaps siderite. Furthermore, corrosion-derived Fe(II) may react with the clay to form Fe(II)-rich silicates. The supercontainer environment will thus experience a volume change and some loss of plasticity of the buffer between the supercontainer and the rock wall may occur. This might promote bacterial activity at the supercontainer surface, which would lead to an enhancement of localised corrosion and probably to destabilisation of the magnetite layer. Previous investigations indicate, however, that there will be no relevant bacterial activity in the main part of the buffer by virtue of its small pore sizes and low water activity. In the course of time, the swelling pressure of bentonite will be affected by a number of processes, including magnetite formation, geochemical degradation, intrusion of bentonite into void space either initially present or created by relative displacement of distance blocks and supercontainer, and by subsequent bentonite erosion. The expected

KBS Technical report 1-120 (1977-1978). Summaries

International Nuclear Information System (INIS)

1979-05-01

The Swedish nuclear utilities started early in 1977 the KBS (nuclear fuel safety) project to study the high level waste problem and report on how and where a safe final storage could be arranged in Sweden. The docummentation produced by the project during 1977 and 1978 has been collected in a series of technical reports numbered from 1 to 120. The English summaries of the technical reports have been collected in this separate volume, No. 121. (G.B.)

Whole-Genome Sequence of the Soil Bacterium Micrococcus sp. KBS0714.

Science.gov (United States)

Kuo, V; Shoemaker, W R; Muscarella, M E; Lennon, J T

2017-08-10

We present here a draft genome assembly of Micrococcus sp. KBS0714, which was isolated from agricultural soil. The genome provides insight into the strategies that Micrococcus spp. use to contend with environmental stressors such as desiccation and starvation in environmental and host-associated ecosystems. Copyright © 2017 Kuo et al.

Freefem++ in THM analyses of KBS-3 deposition hole

International Nuclear Information System (INIS)

Lempinen, A.

2006-12-01

The applicability of Freefem++ as a software for thermo-hydro-mechanical analysis of KBS-3V deposition hole was evaluated. Freefem++ is software for multiphysical simulations with finite element method. A set of previously performed analyses were successfully repeated with Freefem++. The only significant problem was to impose unique values for variables at the canister surface. This problem can be circumvented with an iterative method, and it can possibly be solved later, since Freefem++ is opensource software. (orig.)

Review of the KBS II plan for handling and final storage of unreprocessed spent nuclear fuel

International Nuclear Information System (INIS)

1980-01-01

The Swedish utilities programme for disposal of spent nuclear fuel elements (KBS II) is summarized. Comments and criticism to the programme are given by experts from several foreign or international institutions. (L.E.)

Operational and biological effects zones from base stations of cellular telephony

Energy Technology Data Exchange (ETDEWEB)

Geronikolou, St. A., E-mail: sgeronik@bioacademy.gr [Biomedical Research Foundation Academy of Athens, Athens (Greece); Zimeras, S., E-mail: zimste@aegean.gr [University of the Aegean, Karlovassi, Samos (Greece); Tsitomeneas, S. Th., E-mail: stsit@teipir.gr [Piraeus University of Applied Sciences, Aigaleo (Greece)

2016-03-25

The possible environmental impacts of cellular base stations are operational and biological. The operational effects comprise Εlectro-Μagnetic Interference (EMI), lightning alterations and aesthetic degradation. Both thermal and non-thermal biological effects depend on the absorption of UHF radiofrequencies used. We measured, calculated and estimated the impact zones. The results are: (a) The lightning lethal zone equal to the antenna height, (b) the EMI impact in a zone up to 40m and (c) the ICNIRP’s limits exceed to a zone of 8∼20m into the antenna’s radiation pattern (for 2G GSM and 3G UMTS station). Finally we conclude the adverse effects must not expected in a zone of more than 150m from the radiated antenna, whereas, there is possibility of stochastic effects in intermediate distances (20/40-150m).

Project on Alternative Systems Study - PASS. Comparison of technology of KBS-3, MLH, VLH and VDH concepts by using an expert group

International Nuclear Information System (INIS)

Olsson, Lars; Sandstedt, H.

1992-09-01

This report constitutes a technical comparison and ranking of four repository concepts for final disposal of spent nuclear fuel, that have been studied by SKB: KBS-3, Medium Long Holes (MLH), Very Long Holes (VLH) and Very Deep Holes (VDH). The technical comparison is part of the project 'Project on Alternative Systems Study, PASS', which was initiated by SKB. With the objective of presenting a ranking of the four concepts. Besides this comparison of Technology the ranking is separately made for Long-term Performance and Safety, and Costs before the merging into one verdict. The ranking regarding Technology was carried out in accordance with the method Analytical Hierarchy Process, AHP, and by the aid of expert judgement in the form of a group consisting of six experts. The AHP method implies that the criteria for comparison are ordered in a hierarchy and that the ranking is carried out by pairwise comparison of the criteria. In the evaluation process a measure of the relative importance of each criterion is obtained. The result of the expert judgement exercise was that each expert individually ranked the four concepts in the following order with the top ranked alternative first: KBS-3, MLH, VLH and VDH. The common opinion among the experts was that the top ranking of KBS-3 is significant and the the major criteria used in the study could change substantially without changing the top ranking of KBS-3

KBS-3H. Summary report of work done during Basic Design

International Nuclear Information System (INIS)

Thorsager, Peder; Lindgren, Erik

2004-09-01

The aim of this report is to give a brief specification of achieved knowledge from Basic Design. The report will also constitute the basis for decision to continue the project or not with detail design and manufacturing of deposition equipment and other equipment necessary for realization of full scale demonstrations of horizontal deposition in long horizontal drifts at Aespoe during the period 2004-2007. The work with the project has continued during 2004 with mainly preparation of Request for Proposal (RFP) documents for the detailed design and manufacturing of the deposition equipment. Further, SKB has signed a contract with a drilling company for drilling of the horizontal deposition drifts late 2004 at Aespoe HRL. The work with the buffer issues and the safety case for the KBS-3H concept has also continued during 2004. During the work with the RFP documents for the deposition equipment and excavation of deposition drifts, some modifications or changes have been done that is not documented in this report. The main changes in the KBS-3H projects are the following: 1. The excavation of the deposition drift at Aespoe HRL will not be done with the Wassara water hammer technology as described in the report but with blind raiseboring technology instead. 2. The shell of the super container has been redesigned and also the top and bottom plate of the container are perforated and the thickness has been reduced to 8 mm, the same thickness as the container shell, and the designs of the container feet are modified. The use of an electromagnet for holding the super container during the deposition process is therefore no longer feasible with these thin end plates. The electromagnet is now replaced with a mechanical gripper on the deposition machine. These grippes are holding the front feet of the super container during the deposition process. The reader should therefore be aware that some of the description and conclusion from the Basic Design may have changed somewhat after

KBS-3H. Summary report of work done during Basic Design

Energy Technology Data Exchange (ETDEWEB)

Thorsager, Peder [Ramboell Sverige AB, Stockholm (Sweden); Lindgren, Erik [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

2004-09-01

The aim of this report is to give a brief specification of achieved knowledge from Basic Design. The report will also constitute the basis for decision to continue the project or not with detail design and manufacturing of deposition equipment and other equipment necessary for realization of full scale demonstrations of horizontal deposition in long horizontal drifts at Aespoe during the period 2004-2007. The work with the project has continued during 2004 with mainly preparation of Request for Proposal (RFP) documents for the detailed design and manufacturing of the deposition equipment. Further, SKB has signed a contract with a drilling company for drilling of the horizontal deposition drifts late 2004 at Aespoe HRL. The work with the buffer issues and the safety case for the KBS-3H concept has also continued during 2004. During the work with the RFP documents for the deposition equipment and excavation of deposition drifts, some modifications or changes have been done that is not documented in this report. The main changes in the KBS-3H projects are the following: 1. The excavation of the deposition drift at Aespoe HRL will not be done with the Wassara water hammer technology as described in the report but with blind raiseboring technology instead. 2. The shell of the super container has been redesigned and also the top and bottom plate of the container are perforated and the thickness has been reduced to 8 mm, the same thickness as the container shell, and the designs of the container feet are modified. The use of an electromagnet for holding the super container during the deposition process is therefore no longer feasible with these thin end plates. The electromagnet is now replaced with a mechanical gripper on the deposition machine. These grippes are holding the front feet of the super container during the deposition process. The reader should therefore be aware that some of the description and conclusion from the Basic Design may have changed somewhat after

KBS4FIA: Leveraging advanced knowledge-based systems for financial information analysis

OpenAIRE

García-Sánchez, Francisco; Paredes-Valverde, Mario Andrés; Valencia García, Rafael; Alcaraz Mármol, Gema; Almela Sánchez-Lafuente, Ángela

2017-01-01

Decision making takes place in an environment of uncertainty. Therefore, it is necessary to have information which is as accurate and complete as possible in order to minimize the risk that is inherent to the decision-making process. In the financial domain, the situation becomes even more critical due to the intrinsic complexity of the analytical tasks within this field. The main aim of the KBS4FIA project is to automate the processes associated with financial analysis by leveraging the tech...

The disposal alternative deep boreholes. Content and scope of R and D programme necessary for comparison with the KBS-3 method

International Nuclear Information System (INIS)

Wikberg, P.

2000-08-01

Deposition of spent fuel elements in ≥ 2000 m deep boreholes is an alternative to the KBS-3 method that has been developed in Sweden for more than 20 years. This report gives an account of the research and development needed in order to bring the deep borehole method to the same level of development as the KBS-3 method. Five majors areas are discussed: Geoscience, Technical issues, Technical barriers, Safety assessment and Time-plans and costs. It is estimated that a full R,D and D programme would need about 30 years to be completed, and the costs would amount to around 4 billion SEK (over 400 million USD)

Discrete fracture network modelling of a KBS-3H repository at Olkiluoto

Energy Technology Data Exchange (ETDEWEB)

Lanyon, G.W. (Fracture Systems Ltd, St Ives (United Kingdom)); Marschall, P. (Nagra, Wettingen (Switzerland))

2008-06-15

This report presents Discrete Fracture Network (DFN) models of groundwater flow around a KBS-3H repository situated at Olkiluoto. The study was performed in support of the Safety Case for the KBS-3H Concept, being jointly studied by SKB and Posiva. As part of the preliminary assessment of long term safety of a KBS-3H repository, a Process Report and an Evolution Report (evolution of the disposal system from the emplacement of the first canister to the long term) are being produced. In the course of the task definition the project team identified the need for complementary modelling studies aimed at increasing insight into the hydrodynamic evolution of the disposal system after waste emplacement. In particular, the following issues were identified as requiring input from hydrodynamic models: Probability of high inflow points which may cause buffer erosion. Time transients of inflows after construction of deposition drifts. Interference between deposition drifts and transport tunnels. The DFN models represent the fault and fracture system in the planned repository volume at Olkiluoto. In particular, they represent the hydro geologically significant features. The types of hydrogeological features included in the models are: Major Fracture Zones (MFZs). Local Fracture Zones (LFZs) and associated water conducting features (LFZ-WCFs). Water Conducting Features in the background rock (BR-WCFs). These feature types are derived from the current geological and hydrogeological interpretations developed by Posiva. Several model variants were developed during the study and these variants were used for geometric simulations of the WCF network around the deposition drifts. A simple layout adaptation scheme has been applied to the network models to derive statistics for performance measures relating to the deposition drifts, compartments, plugs and super-containers. A single fracture transient flow model was developed to provide insight to transient flow behaviour around

Discrete fracture network modelling of a KBS-3H repository at Olkiluoto

International Nuclear Information System (INIS)

Lanyon, G.W.; Marschall, P.

2008-06-01

This report presents Discrete Fracture Network (DFN) models of groundwater flow around a KBS-3H repository situated at Olkiluoto. The study was performed in support of the Safety Case for the KBS-3H Concept, being jointly studied by SKB and Posiva. As part of the preliminary assessment of long term safety of a KBS-3H repository, a Process Report and an Evolution Report (evolution of the disposal system from the emplacement of the first canister to the long term) are being produced. In the course of the task definition the project team identified the need for complementary modelling studies aimed at increasing insight into the hydrodynamic evolution of the disposal system after waste emplacement. In particular, the following issues were identified as requiring input from hydrodynamic models: Probability of high inflow points which may cause buffer erosion. Time transients of inflows after construction of deposition drifts. Interference between deposition drifts and transport tunnels. The DFN models represent the fault and fracture system in the planned repository volume at Olkiluoto. In particular, they represent the hydro geologically significant features. The types of hydrogeological features included in the models are: Major Fracture Zones (MFZs). Local Fracture Zones (LFZs) and associated water conducting features (LFZ-WCFs). Water Conducting Features in the background rock (BR-WCFs). These feature types are derived from the current geological and hydrogeological interpretations developed by Posiva. Several model variants were developed during the study and these variants were used for geometric simulations of the WCF network around the deposition drifts. A simple layout adaptation scheme has been applied to the network models to derive statistics for performance measures relating to the deposition drifts, compartments, plugs and super-containers. A single fracture transient flow model was developed to provide insight to transient flow behaviour around

Development of the KBS-3 method. Survey of SKB's research programs and safety assessments, reviews by Government authorities and SKB's international research cooperation; Utvecklingen av KBS-3-metoden. Genomgaang av forskningsprogram, saekerhetsanalyser, myndighetsgranskningar samt SKB:s internationella forskningssamarbete

Energy Technology Data Exchange (ETDEWEB)

2010-11-15

The purpose of this report is to outline the origin and development over the past 30 years (up to 2009) of the KBS-3 method proposed by the Swedish Nuclear Fuel and Waste Management Co (SKB) for final disposal of spent nuclear fuel. The KBS-3 method is based on three protective barriers. The spent nuclear fuel is encapsulated in impermeable copper canisters. The canisters are placed in crystalline basement rock at a depth of 400-700 metres, embedded in bentonite clay. After disposal the tunnels and rock caverns are sealed. The account does not claim to cover all parts of the extensive technical and scientific research and development work conducted by SKB in form of collecting data, refining methods and increasing process understanding. The report forms part of the background material which SKB has gathered as a basis for future applications regarding permits under the Environmental Code and the Nuclear Activities Act to build and operate facilities for encapsulation and final disposal of spent nuclear fuel. A prominent feature of the industrial development work on the final disposal of spent nuclear fuel has been an openness for a constant input of ideas and opinions from society and public bodies (the Government, national authorities, universities and other institutes of higher education, municipalities and various non-governmental organizations). The presentation sheds light on developments in a number of areas that are of central importance for safety in a KBS-3 repository. In SKB's RDandD Programme 2007, these areas go under the headings rock line, buffer line, canister line, backfilling line and closure line. Furthermore, attention has been given to issues related to the possible retrieval of deposited canisters, variants of KBS-3, deposition technology and safety assessment, as well as a number of interdisciplinary issues. The development of methods for the safety assessment has been an important part of the development of the KBS-3 method. The work

Boracéia Biological Station: an ornithological review

Directory of Open Access Journals (Sweden)

Vagner Cavarzere

2010-01-01

Full Text Available Boracéia Biological Station, near the city of Salesópolis, SP, is located in one of the most well-defined centers of endemism in eastern Brazil - the Serra do Mar Center. While the station was established only in 1954 under the auspices of the Museu de Zoologia da Universidade de São Paulo, the avifauna of this locality had already attracted the attention of ornithologists by the 1940s, when the first specimens were collected. Here we describe the ornithological history of the Boracéia Biological Station with a review of all the bird species recorded during more than 68 years, including recent transect and mist-netting records. Boracéia's records were found in museums, literature and unpublished reports that totaled 323 bird species when recent data is also considered. Of these, 117 are endemic to the Atlantic forest and 28 are threatened in the state. Although there are a few doubtful records that need to be checked, some species are the only sightings in the state. Boracéia includes a recently discovered species near the station site and is extremely important for the conservation of Atlantic forest birds.A Estação Biológica de Boracéia, localizada em Salesópolis, SP, situa-se na Serra do Mar, importante região biogeográfica e um dos centros de endemismo mais bem definidos do Brasil. Apesar de instituída em 1954, quando passou a pertencer ao Museu de Zoologia da Universidade de São Paulo, a avifauna desta localidade já era objeto de pesquisas desde a década de 1940, época em que foram realizadas as primeiras coletas de aves. Aqui é apresentada pela primeira vez uma revisão de todos os registros avifaunísticos realizados nessa localidade ao longo de mais de 68 anos assim como a adição de novos registros com base em dados coletados recentemente com transectos lineares e redes de neblina. Os registros para Boracéia estiveram representados em museus, na literatura e em dados não publicados que, somados aos registros

Design process for a repository - KBS-3 case

International Nuclear Information System (INIS)

Svemar, C.

1995-01-01

This paper deals with the design process for the Swedish (generic) repository design KBS-3. The repository may have a spiral access ramp, access shafts, or straight access ramps. Galleries lead from a central service area to a small spent fuel storage area, a larger main spent fuel storage area, and a disposal area for other nuclear waste. This, or any, design has to be planned through three stages of layout and design, viz. feasibility study, preliminary planning, and architectural design, followed by detailed planning, and then planning of excavation and construction. Decisions on final design have to wait until construction is imminent, and all the rock data are available. This means that different sections of the repository may be at different planning stages at any one time. In the last stage, the plan of the disposal holes depends on detailed coring results, because a hole will not be bored where there is a fracture. 3 refs., 1 tab., 3 figs

Studies of buffers behaviour in KBS-3H concept. Work during 2002-2004

Energy Technology Data Exchange (ETDEWEB)

Boergesson, Lennart; Sanden, Torbjoern; Faelth, Billy; Aakesson, Mattias [Clay Technology AB, Lund (Sweden); Lindgren, Erik [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

2005-08-01

In the KBS-3H concept, the deposition tunnels are replace by horizontal 300-m long circular deposition drifts which are excavated from a niche in the transport tunnel. About 40 disposal containers will be deposited in each drift. In order to make the deposition process easier the buffer material and one copper canister are assembled in a steel disposal container, which then is pushed into the deposition drift. The disposal container consists of a perforated steel cylinder in which the buffer material and one copper canister are assembled. Distance blocks of bentonite are placed between each disposal container. The purpose of the distance blocks is to seal off each canister position from the other and to prevent transport of water and bentonite along the drift. The distance blocks also separate one canister from the other in order to get the right temperature of the canister. The total thickness of the distance blocks between the disposal containers is mainly determined by the thermal conductivity of the rock and is expected to be in the range of 3-6 m. The main objective for the KBS-3H concept is that the method provides a more efficient way of depositing the canisters in the rock. The reason is that the deposition tunnels of the KBS-3V concept are not needed and the reduction of rock excavation is therefore about 50 percent. This leads to a lower environmental impact during the construction of the repository but also to a reduced disturbance on the hydro-geological situation in the rock mass. Furthermore, the reduction in rock excavation leads to a significant cost saving for the excavation phase and backfilling of the repository. KBS-3H and KBS-3V are very similar with respect to the behaviour of the bentonite buffer. However, there are some differences that require special attention. An early survey of the differences yielded that there are a number of processes and functions that needed to be investigated for evaluating the feasibility of the concept: 1. The

Safety functions and safety function indicators - key elements in SKB'S methodology for assessing long-term safety of a KBS-3 repository

International Nuclear Information System (INIS)

Hedin, A.

2008-01-01

The application of so called safety function indicators in SKB safety assessment of a KBS-3 repository for spent nuclear fuel is presented. Isolation and retardation are the two main safety functions of the KBS-3 concept. In order to quantitatively evaluate safety on a sub-system level, these functions need to be differentiated, associated with quantitative measures and, where possible, with quantitative criteria relating to the fulfillment of the safety functions. A safety function is defined as a role through which a repository component contributes to safety. A safety function indicator is a measurable or calculable property of a repository component that allows quantitative evaluation of a safety function. A safety function indicator criterion is a quantitative limit such that if the criterion is fulfilled, the corresponding safety function is upheld. The safety functions and their associated indicators and criteria developed for the KBS-3 repository are primarily related to the isolating potential and to physical states of the canister and the clay buffer surrounding the canister. They are thus not directly related to release rates of radionuclides. The paper also describes how the concepts introduced i) aid in focussing the assessment on critical, safety related issues, ii) provide a framework for the accounting of safety throughout the different time frames of the assessment and iii) provide key information in the selection of scenarios for the safety assessment. (author)

Comparison between the KBS-3 method and the deep borehole for final disposal of spent nuclear fuel; Jaemfoerelse mellan KBS-3-metoden och deponering i djupa borrhaal foer slutligt omhaendertagande av anvaent kaernbraensle

Energy Technology Data Exchange (ETDEWEB)

Grundfelt, Bertil (Kemakta Konsult AB (Sweden))

2010-09-15

In this report a comparison is made between disposal of spent nuclear fuel according to the KBS-3 method with disposal in very deep boreholes. The objective has been to make a broad comparison between the two methods, and by doing so to pinpoint factors that distinguish them from each other. The ambition has been to make an as fair comparison as possible despite that the quality of the data of relevance is very different between the methods

Thermal condition of open KBS.3H tunnel

International Nuclear Information System (INIS)

Ikonen, Kari

2008-12-01

This report contains the temperature calculations of open KBS-3H type spent nuclear fuel repository, where the fuel canisters are disposed at horizontal position in horizontal tunnels according to the preliminary SKB (Swedish Nuclear Fuel and Waste Management Co) and Posiva plan. The objective of the study is to simulate the operation phase atmospheric conditions in open horizontal tunnels, where the KBS-3H type canister containers and distance blocks are installed. The analyses concern BWR type canisters. The analyses were made as heat conduction problem by taking into account radiation over gaps. A perforated steel plate surrounds a canister and bentonite. Heat transfer through a perforated plate and surrounding air gaps is a complicated three-dimensional heat transfer problem. To simplify the analysis, the gaps around a container and a distance block were taken into account by describing them by a homogenous layer having effective thermal properties. Convection due to natural circulation of humid air in horizontal gaps between the container and rock was not considered. Convection could reduce the temperature variation in the gap. On the other hand, the perforated steel plate has good conductivity and transfers quite well heat in horizontal gaps. Since the actual temperatures of disposal canisters depend in a complicated way on considered time and position, two extreme cases were studied to make the analyses easier. In the first extreme case an infinite queue of canisters are disposed simultaneously. This case overestimates temperatures, since the actual number of canisters is finite and they are not disposed simultaneously. In other extreme case only the first single canister and the first distance block are disposed. This case underestimates temperatures, since the actual number of canisters is greater than one and the canisters heat each other in later phase. The analysis showed that temperatures differ only a little from each other in the two extreme cases

Thermal condition of open KBS.3H tunnel

Energy Technology Data Exchange (ETDEWEB)

Ikonen, Kari (VTT Processes (Finland))

2008-12-15

This report contains the temperature calculations of open KBS-3H type spent nuclear fuel repository, where the fuel canisters are disposed at horizontal position in horizontal tunnels according to the preliminary SKB (Swedish Nuclear Fuel and Waste Management Co) and Posiva plan. The objective of the study is to simulate the operation phase atmospheric conditions in open horizontal tunnels, where the KBS-3H type canister containers and distance blocks are installed. The analyses concern BWR type canisters. The analyses were made as heat conduction problem by taking into account radiation over gaps. A perforated steel plate surrounds a canister and bentonite. Heat transfer through a perforated plate and surrounding air gaps is a complicated three-dimensional heat transfer problem. To simplify the analysis, the gaps around a container and a distance block were taken into account by describing them by a homogenous layer having effective thermal properties. Convection due to natural circulation of humid air in horizontal gaps between the container and rock was not considered. Convection could reduce the temperature variation in the gap. On the other hand, the perforated steel plate has good conductivity and transfers quite well heat in horizontal gaps. Since the actual temperatures of disposal canisters depend in a complicated way on considered time and position, two extreme cases were studied to make the analyses easier. In the first extreme case an infinite queue of canisters are disposed simultaneously. This case overestimates temperatures, since the actual number of canisters is finite and they are not disposed simultaneously. In other extreme case only the first single canister and the first distance block are disposed. This case underestimates temperatures, since the actual number of canisters is greater than one and the canisters heat each other in later phase. The analysis showed that temperatures differ only a little from each other in the two extreme cases

Swelling of the buffer of KBS-3V deposition hole

International Nuclear Information System (INIS)

Lempinen, A.

2006-12-01

At the time of the installation of spent nuclear fuel canister in the KBS-3V deposition hole, empty space is left around bentonite buffer for technical reasons. The gap between the buffer and the canister is about 10 mm, and the gap between the buffer and the rock is 30 to 35 mm. In this study, the swelling of the buffer to fill the gaps was simulated, when the gaps are initially filled with water and no external water is available. The model used here is a thermodynamical model for swelling clay, with parameters determined for bentonite. The simulations presented here were performed with Freefem++ software, which is a finite element application for partial differential equations. These equations come from the material model. The simulation results show that the swelling fills the outer gaps in few years, but no significant swelling pressure is generated. For swelling pressure, external water supply is required. (orig.)

Development of the KBS-3 method. Survey of SKB's research programs and safety assessments, reviews by Government authorities and SKB's international research cooperation

International Nuclear Information System (INIS)

2010-11-01

The purpose of this report is to outline the origin and development over the past 30 years (up to 2009) of the KBS-3 method proposed by the Swedish Nuclear Fuel and Waste Management Co (SKB) for final disposal of spent nuclear fuel. The KBS-3 method is based on three protective barriers. The spent nuclear fuel is encapsulated in impermeable copper canisters. The canisters are placed in crystalline basement rock at a depth of 400-700 metres, embedded in bentonite clay. After disposal the tunnels and rock caverns are sealed. The account does not claim to cover all parts of the extensive technical and scientific research and development work conducted by SKB in form of collecting data, refining methods and increasing process understanding. The report forms part of the background material which SKB has gathered as a basis for future applications regarding permits under the Environmental Code and the Nuclear Activities Act to build and operate facilities for encapsulation and final disposal of spent nuclear fuel. A prominent feature of the industrial development work on the final disposal of spent nuclear fuel has been an openness for a constant input of ideas and opinions from society and public bodies (the Government, national authorities, universities and other institutes of higher education, municipalities and various non-governmental organizations). The presentation sheds light on developments in a number of areas that are of central importance for safety in a KBS-3 repository. In SKB's RDandD Programme 2007, these areas go under the headings rock line, buffer line, canister line, backfilling line and closure line. Furthermore, attention has been given to issues related to the possible retrieval of deposited canisters, variants of KBS-3, deposition technology and safety assessment, as well as a number of interdisciplinary issues. The development of methods for the safety assessment has been an important part of the development of the KBS-3 method. The work with

Comparison between the KBS-3 method and the deep borehole for final disposal of spent nuclear fuel

International Nuclear Information System (INIS)

Grundfelt, Bertil

2010-09-01

In this report a comparison is made between disposal of spent nuclear fuel according to the KBS-3 method with disposal in very deep boreholes. The objective has been to make a broad comparison between the two methods, and by doing so to pinpoint factors that distinguish them from each other. The ambition has been to make an as fair comparison as possible despite that the quality of the data of relevance is very different between the methods

Bioremediation of oil contaminated soil from service stations. Evaluation of biological treatment

International Nuclear Information System (INIS)

Puustinen, J.; Jorgensen, K.S.; Strandberg, T.; Suortti, A.M.

1995-01-01

Biological treatment of contaminated soil has received much attention during the last decade. Microbes are known to be able to degrade many oil hydrocarbons. However, research is needed to ensure that new technologies are implemented in a safe and reliable way under Finnish climatic conditions. The main points of interest are the rate of the degradation as well as the survival and efficiency of microbial inoculants possibly introduced during the treatment. During 1993 the biotreatability of oil-contaminated soil from service stations was investigated in cooperation with the Finnish Petroleum Federation. The goal of this field-scale study was to test how fast lubrication oil can be composted during one Finnish summer season and to find out whether microbial inoculants would enhance the degradation rate. The soil was excavated from three different service stations in the Helsinki metropolitan area and was transported to a controlled composting area. The soil was sieved and compost piles, also called biopiles, were constructed on the site. Bark chips were used as the bulking agent and nutrients and lime were added to enhance the biological activity. Two different commercial bacterial inoculants were added to two of the piles. The piles were turned by a tractor-drawn screw-type mixer at two to four weeks interval. Between the mixings, the piles were covered with tarpaulins to prevent evaporation and potential excessive wetting. Several microbiological parameters were determined during the test period as well as the temperature and mineral oil content

Final repository for spent nuclear fuel in granite - the KBS-3V concept in Sweden and Finland

International Nuclear Information System (INIS)

Pettersson, Stig; Loennerberg, Bengt

2008-01-01

Both Sweden and Finland has advanced plans for design, construction and operation of the final repositories for direct disposal of spent nuclear fuel. Both countries have the same type of host rock - granite. They are also investigating alternative concept for disposal, vertical or horizontal disposal of the canisters with encapsulated spent nuclear fuel, normally called KBS-3V or the KBS-3H disposal concept. The development of the KBS-3V concept started around 1980 and is the reference method for both SKB in Sweden and Posiva in Finland. However, extensive development work is ongoing since 2001 with KBS-3H in order to bring that concept to the same maturity as KBS-3V. This presentation deals with the design and operation of the KBS-3V based on the work done within Sweden and SKB but the development is Finland is identical and it is a close cooperation between SKB in Sweden and Posiva in Finland. In Sweden, the site investigation for location of the repository has been concentrated on two sites, in the Oskarshamn area, about 350 km south of Stockholm, and the Forsmark area, about 180 km north of Stockholm. For information it can be mentioned that Finland plans to locate their repository in the vicinity of the Olkiluoto nuclear power plant site, about 300 km north of Helsinki. The site investigation is completed and the selection of site is scheduled to mid 2009 and sending in the application for location and construction of the repository is scheduled to end 2009. After receiving all necessary permits, construction time and commissioning will take about 7 to 8 years and operation is expected to start about 2020. The KBS-3 system is based on a multi barrier concept and the work with compiling the design requirements for the underground part of the deep repository has been ongoing for some time within the SKB organisation. Today the design requirements for the underground part are documented in a big number of reports that has been produced by specialists and working

General construction requirements for the deep repository in the KBS-3 system

International Nuclear Information System (INIS)

2002-10-01

The KBS-3 systems includes equipment and plants for transport of spent nuclear fuels and encapsulated spent fuels, central intermediate storage, encapsulation and deep geologic disposal. The requirements in this document concern the repository and have been put together in view of the tasks of designing, constructing and building the repository. The report presents: A general review of existing design plans; Laws and regulations relevant for the design of the repository; How the regulations have been broken down to functional demands and dimensioning requirements for the repository; How the site conditions influence the design, and how the layout of the different parts of the repository interact; Relations between the functions of the repository, the safety and the design; A foundation for developing construction plans for the repository. The requirements will be collected in a database that will develop as new knowledge is collected

SANDERLING Final Report: Parts A and B, A Research Study into KBS for Command and Control in Naval and TMD Applications

Science.gov (United States)

1990-04-01

fashion (from both the aspects of finance and effort). Huge amounts of effort have been invested in developing formal and rigorous verification and...validation methods for C2 systems employing conventional software techniques. However, little investment has been made for KBS techniques as most of...panning and scheduling) • Bath University ( fundemental research on novel methods of optimisation) - Prof. Silverman. Cambridge University (recovery

Biological dosimetry to determine the UV radiation climate inside the MIR station and its role in vitamin D biosynthesis

Science.gov (United States)

Rettberg, P.; Horneck, G.; Zittermann, A.; Heer, M.

1998-11-01

The vitamin D synthesis in the human skin, is absolutely dependent on UVB radiation. Natural UVB from sunlight is normally absent in the closed environment of a space station like MIR. Therefore it was necessary to investigate the UV radiation climate inside the station resulting from different lamps as well as from occasional solar irradiation behind a UV-transparent quartz window. Biofilms, biologically weighting and integrating UV dosimeters successfully applied on Earth (e.g. in Antarctica) and in space (D-2, Biopan I) were used to determine the biological effectiveness of the UV radiation climate at different locations in the space station. Biofilms were also used to determine the personal UV dose of an individual cosmonaut. These UV data were correlated with the concentration of vitamin D in the cosmonaut's blood and the dietary vitamin D intake. The results showed that the UV radiation climate inside the Mir station is not sufficient for an adequate supply of vitamin D, which should therefore be secured either by vitamin D supplementat and/or by the regular exposure to special UV lamps like those in sun-beds. The use of natural solar UV radiation through the quartz window for `sunbathing' is dangerous and should be avoided even for short exposure periods.

BIOLOGICAL AND ENVIRONMENTAL RADIATION EXPERIENCE AT INDIAN POINT STATION

Energy Technology Data Exchange (ETDEWEB)

Nelson, H. F.

1963-09-15

The environs monitoring program at Indian Point Station is presented. Thirty sampling stations within a circle of approximately 10 miles of the station are used for the collection of samples of air, water, vegetation, and soil that are then analyzed for gross beta-gamma activity. Data are tabulated. (P.C.H.)

Vegetation composition of the UCM Biological Field Station Finca de Ontalba; Composicion vegetal de la Estacion Biologica de la UCM Finca de Ontalba

Energy Technology Data Exchange (ETDEWEB)

Castoldi, E.; Molina, J. A.

2012-07-01

A vegetation study in the Biological Field Station of the Complutense University of Madrid named Finca de Ontalba, located in Guadarrama Mountains (North Madrid), was carried out. We identified 12 plant communities grouped in the following seven vegetation types: 1) Hygrophilous and aquatic communities; 2) Meadows; 3) Pioneer community of open disturbed soils; 4) Nitrophilous tall-herb vegetation of forest edge; 5) Forest-edge herbaceous community; 6) Forest-edge scrub community; and 7) Forest vegetation. The interest of the Station for research studies is pointed out. Its scope includes primary succession, amphibious environment, soil moisture gradient, ecotones, and forested environment. Besides, the Biological Station hosts a freshwater habitat type listed in the European Community Directive (92/43/EEC) which corresponds to water courses of plain or montane levels with Ranunculion fluitantis and Callitricho- Batrachion vegetation (habitat code 3260). (Author)

Akttvitas Selulase, Amilase Dan Invertase Pada Tanah Kebun Biologi Wamena*[cellulase, Amylase and Invertase Activities Achieved From Soil of Wamena Biological Research Station

OpenAIRE

Rahmansyah, M; Latupapua, HJD

2003-01-01

Enzymatic activities in soil as due to microbes action in organic matter degradation, lead to propose as indicators for determining soil degree enrichment.In this work, the enzymatic activities of cellulase, invertase and amylase were determined in tropical soil collected from Biological Research Station in Wamena. Result of measurement on five soil samples showed that cellulase activity occurred between 0.10 - 0.31 mg reducing sugar/g soil/hour in 2% Carboxymethylcellulose (CMC) substrate, a...

[Investigation of microbial contamination of the air and equipment of a biological waste water purification station].

Science.gov (United States)

Alikbaeva, L A; Figurovskiĭ, A P; Vasil'ev, O D; Ermolaev-Makovskiĭ, M A; Merkur'eva, M A

2010-01-01

The paper describes the results of a study of ambient air microbiological pollution in the working premises and equipment surfaces in the main shops of the biological waste water purification station of a cardboard-polygraphic plant. The findings suggest that there is high microbial contamination of the working environment, which should be born in mind on developing measures to optimize working conditions and on studying morbidity rates among the workers.

SAFE-KBS, Substantiating the safety of systems containing knowledge-based components

International Nuclear Information System (INIS)

Mesa, E.; Jimenez, A.

1998-01-01

The overall objective of the Safe-KBS project is to develop generic development and certification methodologies that allow the introduction of knowledge-based components in safety-related applications. The expert system technology presents a set of features, such as the capability to provide the rationale for its conclusions, that may significantly contribute to the new operation support systems. Nevertheless, the use of this technology in safety-related applications is limited by the lack of recognised methodologies and standards that allow a formal demonstration of the quality and reliability of these systems, as required for obtaining the approval for their use at nuclear power plants. The development methodology is structured in three hierarchical levels: life cycle model, i.e., processes and activities constituting the life cycle, life cycle plans, i.e., tasks, and support packages, i.e., set of techniques and methods to perform certain activities or tasks. The certification methodology consists of a set of certification requirements and a certification scheme for demonstrating the compliance with these requirements. This project was developed within the European framework ESPRIT, with the collaboration of Sextant, Cise, Qualience, Ilog, Computes, DNV and Uninfo. (Author)

Quantitative Assessment of the Potential Significance of Colloids to the KBS-3 Disposal Concept

International Nuclear Information System (INIS)

Klos, R.A.; White, M.J.; Wickham, S.M.; Bennett, D.G.; Hicks, T.W.

2002-06-01

Colloids are minute particles in the size range 1 nm to 1 μm that can remain suspended in water, and may influence radionuclide transport in radioactive waste disposal systems. Galson Sciences Ltd (GSL) has undertaken a quantitative assessment of the impact that colloid-facilitated radionuclide transport may have on the performance of the Swedish KBS-3 concept for disposal of high-level radioactive waste and spent fuel. This assessment has involved the evaluation and application of SKI's colloid transport model, COLLAGE II, modelling of km-scale Pu transport at the Nevada Test Site (NTS), USA, and identification of circumstances under which colloid-facilitated transport could be important for a KBS-3-type environment. Colloids bearing traces of plutonium from the BENHAM underground nuclear test have been detected in samples obtained from Nevada Test Site (NTS) groundwater wells 1.3 km from the detonation point. Plutonium is generally fairly immobile in groundwater systems, and it has been suggested that colloids may have caused the plutonium from the BENHAM test to be transported 1.3 km in only 30 years. This hypothesis has been tested by modelling plutonium transport in a fracture with similar characteristics to those present in the vicinity of the BENHAM test. SKI's colloid transport code, COLLAGE II, considers radionuclide transport in a one-dimensional planar fracture and represents radionuclide-colloid sorption and desorption assuming first-order, linear kinetics. Recently published data from both the ongoing NTS site investigation and from the associated Yucca Mountain Project have been used to define a COLLAGE II dataset. The kinetics of radionuclide-colloid sorption and desorption have been found to be crucial in explaining the transport of plutonium associated with colloids, as inferred at the NTS. Specifically, it has been found that for plutonium to have been transported by colloids over the full 1.3 km transport path, it is likely that the plutonium

Temperature field due to time-dependent heat sources in a large rectangular grid. Application for the KBS-3 repository

International Nuclear Information System (INIS)

Probert, T.; Claesson, Johan

1997-04-01

In the KBS-3 concept canisters containing nuclear waste are deposited along parallel tunnels over a large rectangular area deep below the ground surface. The temperature field in rock due to such a rectangular grid of heat-releasing canisters is studied. An analytical solution for this problem for any heat source has been presented in a preceding paper. The complete solution is summarized in this paper. The solution is by superposition divided into two main parts. There is a global temperature field due to the large rectangular canister area, while a local field accounts for the remaining heat source problem. In this sequel to the first report, the local solution is discussed in detail. The local solution consists of three parts corresponding to line heat sources along tunnels, point heat sources along a tunnel and a line heat source along a canister. Each part depends on two special variables only. These parts are illustrated in dimensionless form. Inside the repository the local temperature field is periodic in the horizontal directions and has a short extent in the vertical direction. This allows us to look at the solution in a parallelepiped around a canister. The solution in the parallelepiped is valid for all canisters that are not too close to the repository edges. The total temperature field is calculated for the KBS-3 case. The temperature field is calculated using a heat release that is valid for the first 10 000 years after deposition. The temperature field is shown in 23 figures in order to illustrate different aspects of the complex thermal process

Thermal analyses of KBS-3H type repository

International Nuclear Information System (INIS)

Ikonen, K.

2003-12-01

This report contains the temperature dimensioning of the KBS-3H type nuclear fuel repository, where the fuel canisters are disposed at horizontal position in the horizontal tunnels according to the preliminary SKB (Swedish Nuclear Fuel and Waste Management Co) and Posiva plan. The maximum temperature on the canister surface is limited to the design temperature of +100 deg C. However, due to uncertainties in thermal analysis parameters (like scattering in rock conductivity) the allowable calculated maximum canister temperature is set to 90 deg C causing a safety margin of 10 deg C. The allowable temperature is controlled by adjusting the space between adjacent canisters, adjacent tunnels and the distance between separate panels of the repository and the pre-cooling time affecting power of the canisters. With reasonable canister and tunnel spacing the maximum temperature 90 deg C is achieved with an initial canister power of 1700 W. It became apparent that the temperature of canister surfaces can be determined by superposing analytic line heat source models much more efficiently than by numerical analysis, if the analytic model is first verified and calibrated by numerical analysis. This was done by comparing the surface temperatures of the central canister in a single infinite canister queue calculated numerically and analytically. In addition, the results from SKB analysis were used for comparison and for confirming the calculation procedure. For the Olkiluoto repository a reference case of one panel having 1500 canisters was analysed. The canisters are disposed in a rectangular geometry in a certain order. The calculation was performed separately for both Olkiluoto BWR canisters and Loviisa PWR canisters. The result was the minimum allowable spacing between canisters. (orig.)

Safety case approach for a KBS-3 type repository in crystalline rock

International Nuclear Information System (INIS)

Pastina, Barbara; Lehikoinen, Jarmo; Puigdomenech, Ignasi

2012-01-01

Barbara Pastina of Saanio and Riekkola described the approach to considering cementitious materials in a safety case for a KBS-3 repository in Finland. In this concept, cements will be used predominantly as tunnel plugs and seals. Part of the Finnish approach has involved identifying the cement-related FEPs. For example, FEPs representing the effects of cement on spent fuel, on the canister and on radionuclide transport include: - Fuel matrix dissolution at high pH. - Copper corrosion at high pH. - Radionuclide speciation and solubility at high pH. - Radionuclide sorption and diffusion at high pH. - Radionuclide transport due to organic materials (e.g. super-plasticisers). - Colloid formation at a high pH plume front. FEPs representing the effects of cement on bentonite in the buffer and backfill include: - Potential changes in swelling pressure due to mass loss, decrease in clay density, and precipitation of secondary minerals. - Potential cracking and increase of hydraulic conductivity due to cementation. - Increase of the cation exchange capacity due to the loss of silica from the montmorillonite structure. Amongst the cement-related FEPs, the main concerns are related to effects on the performance of the bentonite buffer. Cement-bentonite interactions are complex, there are few experimental data, and there are significant modelling uncertainties (e.g. limited knowledge about the reactions that may occur and their rates, and the effects of temperature). Accepting the existence of various uncertainties, preliminary modelling studies performed using the TOUGHREACT code illustrate the potential for porosity reduction and clogging of porosity in bentonite affected by cementitious pore waters. The modelling also suggests that that the high pH of the pore waters moving from the cementitious materials into the bentonite may be rapidly lowered as a result of reactions with the bentonite close to the cement-bentonite interface. Taking account of the various research and

Vitrified radwaste from reprocessing. Material concerning the examination by the Swedish Nuclear Power Inspectorate of the supplementary geology report from the KBS-project

International Nuclear Information System (INIS)

1979-01-01

The Swedish Nuclear Power Inspectorate was designated by the Swedish Government to examine the supplementary geologic investigations performed by the utilities' KBS-project and to judge wheather the area investigated, Sternoe in southern Sweden, could be used for constructing a safe repository for radioactive wastes or not. This report contains material that was ordered by or sent to the Nuclear Power Inspectorate as well as the report by the Inspectorate to the Government. (L.E.)

A synchrotron-based X-ray exposure station for radiation biology experiments

International Nuclear Information System (INIS)

Thompson, A.C.; Blakely, E.A.; Bjornstad, K.A.; Chang, P.Y.; Rosen, C.J.; Schwarz, R.I.

2007-01-01

Synchrotron X-ray sources enable radiation biology experiments that are difficult with conventional sources. A synchrotron source can easily deliver a monochromatic, tunable energy, highly collimated X-ray beam of well-calibrated intensity. An exposure station at beamline 10.3.1 of the Advanced Light Source (ALS) has been developed which delivers a variable energy (5-20 keV) X-ray fan beam with very sharp edges (10-90% in less than 3 μm). A series of experiments have been done with a four-well slide where a stripe (100 μm widex18 mm long) of cells in each well has been irradiated and the dose varied from well to well. With this facility we have begun a series of experiments to study cells adjacent to irradiated cells and how they respond to the damage of their neighbors. Initial results have demonstrated the advantages of using synchrotron radiation for these experiments

A synchrotron-based X-ray exposure station for radiation biology experiments

Energy Technology Data Exchange (ETDEWEB)

Thompson, A.C. [Division of Life Sciences, Lawrence Berkeley National Laboratory, Bld. 50A-6120, Berkeley, CA 94720 (United States)], E-mail: acthompson@lbl.gov; Blakely, E.A.; Bjornstad, K.A. [Division of Life Sciences, Lawrence Berkeley National Laboratory, Bld. 50A-6120, Berkeley, CA 94720 (United States); Chang, P.Y. [Division of Life Sciences, Lawrence Berkeley National Laboratory, Bld. 50A-6120, Berkeley, CA 94720 (United States); SRI International, Menlo Park, CA (United States); Rosen, C.J.; Schwarz, R.I. [Division of Life Sciences, Lawrence Berkeley National Laboratory, Bld. 50A-6120, Berkeley, CA 94720 (United States)

2007-11-11

Synchrotron X-ray sources enable radiation biology experiments that are difficult with conventional sources. A synchrotron source can easily deliver a monochromatic, tunable energy, highly collimated X-ray beam of well-calibrated intensity. An exposure station at beamline 10.3.1 of the Advanced Light Source (ALS) has been developed which delivers a variable energy (5-20 keV) X-ray fan beam with very sharp edges (10-90% in less than 3 {mu}m). A series of experiments have been done with a four-well slide where a stripe (100 {mu}m widex18 mm long) of cells in each well has been irradiated and the dose varied from well to well. With this facility we have begun a series of experiments to study cells adjacent to irradiated cells and how they respond to the damage of their neighbors. Initial results have demonstrated the advantages of using synchrotron radiation for these experiments.

Multiple Paternity in a Reintroduced Population of the Orinoco Crocodile (Crocodylus intermedius) at the El Frío Biological Station, Venezuela.

Science.gov (United States)

Rossi Lafferriere, Natalia A; Antelo, Rafael; Alda, Fernando; Mårtensson, Dick; Hailer, Frank; Castroviejo-Fisher, Santiago; Ayarzagüena, José; Ginsberg, Joshua R; Castroviejo, Javier; Doadrio, Ignacio; Vilá, Carles; Amato, George

2016-01-01

The success of a reintroduction program is determined by the ability of individuals to reproduce and thrive. Hence, an understanding of the mating system and breeding strategies of reintroduced species can be critical to the success, evaluation and effective management of reintroduction programs. As one of the most threatened crocodile species in the world, the Orinoco crocodile (Crocodylus intermedius) has been reduced to only a few wild populations in the Llanos of Venezuela and Colombia. One of these populations was founded by reintroduction at Caño Macanillal and La Ramera lagoon within the El Frío Biological Station, Venezuela. Twenty egg clutches of C. intermedius were collected at the El Frío Biological Station for incubation in the lab and release of juveniles after one year. Analyzing 17 polymorphic microsatellite loci from 335 hatchlings we found multiple paternity in C. intermedius, with half of the 20 clutches fathered by two or three males. Sixteen mothers and 14 fathers were inferred by reconstruction of multilocus parental genotypes. Our findings showed skewed paternal contributions to multiple-sired clutches in four of the clutches (40%), leading to an overall unequal contribution of offspring among fathers with six of the 14 inferred males fathering 90% of the total offspring, and three of those six males fathering more than 70% of the total offspring. Our results provide the first evidence of multiple paternity occurring in the Orinoco crocodile and confirm the success of reintroduction efforts of this critically endangered species in the El Frío Biological Station, Venezuela.

Multiple Paternity in a Reintroduced Population of the Orinoco Crocodile (Crocodylus intermedius at the El Frío Biological Station, Venezuela.

Directory of Open Access Journals (Sweden)

Natalia A Rossi Lafferriere

Full Text Available The success of a reintroduction program is determined by the ability of individuals to reproduce and thrive. Hence, an understanding of the mating system and breeding strategies of reintroduced species can be critical to the success, evaluation and effective management of reintroduction programs. As one of the most threatened crocodile species in the world, the Orinoco crocodile (Crocodylus intermedius has been reduced to only a few wild populations in the Llanos of Venezuela and Colombia. One of these populations was founded by reintroduction at Caño Macanillal and La Ramera lagoon within the El Frío Biological Station, Venezuela. Twenty egg clutches of C. intermedius were collected at the El Frío Biological Station for incubation in the lab and release of juveniles after one year. Analyzing 17 polymorphic microsatellite loci from 335 hatchlings we found multiple paternity in C. intermedius, with half of the 20 clutches fathered by two or three males. Sixteen mothers and 14 fathers were inferred by reconstruction of multilocus parental genotypes. Our findings showed skewed paternal contributions to multiple-sired clutches in four of the clutches (40%, leading to an overall unequal contribution of offspring among fathers with six of the 14 inferred males fathering 90% of the total offspring, and three of those six males fathering more than 70% of the total offspring. Our results provide the first evidence of multiple paternity occurring in the Orinoco crocodile and confirm the success of reintroduction efforts of this critically endangered species in the El Frío Biological Station, Venezuela.

Report on terrestrial biology research and logistics at Baia Terra Nova Station

Directory of Open Access Journals (Sweden)

Satoshi Imura

1999-11-01

Full Text Available From December 4,1998 to January 15,1999,the author stayed at Baia Terra Nova Station (Italy in Antarctica, as an exchange scientist. To compare the biodiversity between Syowa Station and the Baia Terra Nova Station area, many samples of mosses, lichens, algae and micro animals in the soil were collected, and the structure of moss vegetation was studied in various fields around the station. Some characteristic features of logistics at the station were also researched.

Biotechnology opportunities on Space Station

Science.gov (United States)

Deming, Jess; Henderson, Keith; Phillips, Robert W.; Dickey, Bernistine; Grounds, Phyllis

1987-01-01

Biotechnology applications which could be implemented on the Space Station are examined. The advances possible in biotechnology due to the favorable microgravity environment are discussed. The objectives of the Space Station Life Sciences Program are: (1) the study of human diseases, (2) biopolymer processing, and (3) the development of cryoprocessing and cryopreservation methods. The use of the microgravity environment for crystal growth, cell culturing, and the separation of biological materials is considered. The proposed Space Station research could provide benefits to the fields of medicine, pharmaceuticals, genetics, agriculture, and industrial waste management.

Characterization of airborne bacteria at an underground subway station.

Science.gov (United States)

Dybwad, Marius; Granum, Per Einar; Bruheim, Per; Blatny, Janet Martha

2012-03-01

The reliable detection of airborne biological threat agents depends on several factors, including the performance criteria of the detector and its operational environment. One step in improving the detector's performance is to increase our knowledge of the biological aerosol background in potential operational environments. Subway stations are enclosed public environments, which may be regarded as potential targets for incidents involving biological threat agents. In this study, the airborne bacterial community at a subway station in Norway was characterized (concentration level, diversity, and virulence- and survival-associated properties). In addition, a SASS 3100 high-volume air sampler and a matrix-assisted laser desorption ionization-time of flight mass spectrometry-based isolate screening procedure was used for these studies. The daytime level of airborne bacteria at the station was higher than the nighttime and outdoor levels, and the relative bacterial spore number was higher in outdoor air than at the station. The bacterial content, particle concentration, and size distribution were stable within each environment throughout the study (May to September 2010). The majority of the airborne bacteria belonged to the genera Bacillus, Micrococcus, and Staphylococcus, but a total of 37 different genera were identified in the air. These results suggest that anthropogenic sources are major contributors to airborne bacteria at subway stations and that such airborne communities could harbor virulence- and survival-associated properties of potential relevance for biological detection and surveillance, as well as for public health. Our findings also contribute to the development of realistic testing and evaluation schemes for biological detection/surveillance systems by providing information that can be used to mimic real-life operational airborne environments in controlled aerosol test chambers.

Characterization of Airborne Bacteria at an Underground Subway Station

Science.gov (United States)

Dybwad, Marius; Granum, Per Einar; Bruheim, Per

2012-01-01

The reliable detection of airborne biological threat agents depends on several factors, including the performance criteria of the detector and its operational environment. One step in improving the detector's performance is to increase our knowledge of the biological aerosol background in potential operational environments. Subway stations are enclosed public environments, which may be regarded as potential targets for incidents involving biological threat agents. In this study, the airborne bacterial community at a subway station in Norway was characterized (concentration level, diversity, and virulence- and survival-associated properties). In addition, a SASS 3100 high-volume air sampler and a matrix-assisted laser desorption ionization–time of flight mass spectrometry-based isolate screening procedure was used for these studies. The daytime level of airborne bacteria at the station was higher than the nighttime and outdoor levels, and the relative bacterial spore number was higher in outdoor air than at the station. The bacterial content, particle concentration, and size distribution were stable within each environment throughout the study (May to September 2010). The majority of the airborne bacteria belonged to the genera Bacillus, Micrococcus, and Staphylococcus, but a total of 37 different genera were identified in the air. These results suggest that anthropogenic sources are major contributors to airborne bacteria at subway stations and that such airborne communities could harbor virulence- and survival-associated properties of potential relevance for biological detection and surveillance, as well as for public health. Our findings also contribute to the development of realistic testing and evaluation schemes for biological detection/surveillance systems by providing information that can be used to mimic real-life operational airborne environments in controlled aerosol test chambers. PMID:22247150

Review of DDH 280 citadel cleansing station development. Memorandum report

Energy Technology Data Exchange (ETDEWEB)

Dyck, W.R.; McAndless, J.M.; Ho, J.

1994-02-01

A mock-up of a DDH 280 class destroyer Aft Cleansing Station has been modified following several technical evaluations. Chemical and biological simulant trials have been carried out and in the conclusion of these trials it was stated that the integrity of the citadel was maintained within a chemical or biological environment. Procedures have been developed which allowed a single man, or a group of men, or a casualty to proceed through an Aft Cleansing Station with minimum effort, and in a coordinated fashion. Evaluations have now been completed where the cleansing station and the personnel passing through it were challenged with the biological simulant Bacillus globigii (BG), and the chemical intake simulant dimethyl sulfoxide (DMSO). It was concluded, that when the cleansing station was operated properly, and the new procedures were being followed, it was possible to process contaminated personnel through the citadel entry system, and maintain the integrity of the citadel.

The viability of biological treatment at Ibi wastewater treatment station; Viabilidad del tratamiento biologico de aguas residuales

Energy Technology Data Exchange (ETDEWEB)

Flor Garcia, M.V.; Morenilla Martinez, J.J.; Ruiz Zapata, R.

1996-06-01

In this study, we have proved the viability of biological treatment of leaving waters from Ibi Wastewater Treatment Station, where water is subject to the action of coagulant agents, following a physical and chemical process. the experience was based on wastewater treatment by using activated sludge, at experimental scale in a pilot plant. During the experiments, we controlled the main parameters which indicate treatment success; namely, Suspended Solids (SS), pH, Biochemical Oxygen Demand (BOD) and Chemical Oxygen Demand (COD), in addition to other substances such as nutrients and toxicants, and inhibitors of bio metabolism. (Author) 6 refs.

Radionuclide transport paths in the nearfield - a KBS-3 concept study

International Nuclear Information System (INIS)

Pusch, R.

1990-07-01

The general scope of the study has been to identify and define major paths for radionuclide transport from KBS3 canisters, focusing on the nearfield rock. A primary purpose was to document the hydraulic properties of the 'disturbed zones' around blasted tunnels and it is concluded from compilation of theoretical data and field experiment recording that stress relief and blasting effects combine to form a previous zone that extends to about 1 m from the tunnel periphery. It has an average, isotropic hydraulic conductivity of no less than 10 -8 m/s. A second major purpose of the study was to generalize the structure of granitic rock with respect to water-bearing fractures. Forsmark, Finnsjoen, and Stripa data have been considered and found to support the idea of rather regular 'orthogonal' fracture systems with relatively large spacings. The hydraulically active part of the fractures, which can be characterized by simple statistical distributions of persistence, spacing, and aperture, is formed by channels, which can be taken as plane, straight stripes with constant width and aperture. The width can be assumed on the basis of field observations while the aperture is estimated from the bulk conductivity and the geometry of the fracture network. The major transport paths of the rock have been concretized and combined to form a general simplified model intended for calculation of radionuclide transport through water flow and through diffusion through continuous water passages. This model comprises of a circumscribing pervious zone of 'wall disturbance' around the deposition holes in addition to the fracture channels. (author)

Weather Station: Hawaii: Oahu: Coconut Island

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Hawaii Institute of Marine Biology (HIMB) automatic weather station (AWS) records hourly measurements of precipitation, air temperature, wind speed and...

Pilot tests for dismantling by blasting of the biological shield of a shut down nuclear power station

International Nuclear Information System (INIS)

Freund, H.U.

1995-01-01

Following free-field tests on concrete blocks the feasibility of explosive dismantling of the biological shield of nuclear power stations has been succesfully tested at the former hotsteam reaction in Karlstein/Main Germany. For this purpose a model shield of scale 1:2 was embedded into the reactor structure at which bore-hole blasting tests employing up to about 15 kg of explosive were performed. An elaborate measurement system allowed to receive detailed information on the blast side-effects: Special emphasis was focussed on the quantitative registration of the dynamic blast loads; data for the transfer of the dismantling method to the removal of real ractor structures were obtained. (orig.) [de

Modelling the redox front movement in a KBS-3 nuclear waste repository

International Nuclear Information System (INIS)

Romero, L.; Moreno, L.; Neretnieks, I.

1993-05-01

In a KBS-3 repository for spent nuclear fuel, radiolysis can occur if canisters are breached and water comes into contact with the fuel. The oxidants produced by radiolysis may migrate into the clay surrounding the canister and change the redox conditions from reducing to oxidizing. If much oxidants are produced, they can migrate to the water flowing in the fractures in the rock. Some of the oxidants also may oxidize the uranium and other nuclides in the fuel and make them more soluble. The nuclides will then migrate out in a higher oxidation state and may precipitate at the redox front. Calculations were done for a production of 144 moles of oxidants in one million years. A higher and a much lower production were also considered. It was assumed that the canister is either totally or locally corroded. The results show that, for the most probable production rate, a large fraction of oxidants would be consumed in the clay. If the corrosion is local and there is a fracture opposite the damage, the amount of oxidant transported into the fracture would be significant. Here the advance of the redox front in the fracture would be some tens of metres. For the lowest production rate, the oxidants never reach the fractures in the rock. Only with improbably high production rates could the tips of the redox front move very long distances, in isolated channels that are not part of a network

SR 97: Post-closure safety for a KBS 3 type deep repository for spent nuclear fuel

International Nuclear Information System (INIS)

Hedin, A.; Kautsky, U.

2000-03-01

Prior to coming site investigations for siting of a deep repository for spent nuclear fuel, SKB has carried out the long-term safety assessment SR 97, requested by the Swedish Government. The repository is of the KBS-3 type, where the fuel is placed in isolating copper canisters with a high-strength cast iron insert. The canisters are surrounded by bentonite clay in individual deposition holes at a depth of 500 m in granitic bedrock. The future evolution of the repository system is analysed in the form of five scenarios. The first is a base scenario where the repository is postulated to be built entirely according to specifications and where present-day conditions in the surroundings, including climate, persist. The four other scenarios show the evolution if the repository contains a few initially defective canisters, in the event of climate change, in the event of earthquakes, and in the event of future inadvertent human intrusion. The principal conclusion of the assessment is that the prospects of building a safe deep repository for spent nuclear fuel in Swedish granitic bedrock are very good. (author)

The application of risk analysis methods for the evaluation of the KBS-II encapsulation plant

International Nuclear Information System (INIS)

Olshausen, K.D.

1981-01-01

Following a short description of the process of risk analysis and a definition of the objective, the encapsulation plant is described to the extent required. For certain systems, e.g. ventilation, the data was insufficient and some assumptions had to be made. A number of critical events were identified, and one of these, the release of radioactive substances through the ventilation system, was chosen for more detailed analysis. The plant was regarded as a system of barriers to which the substance had to be transported (TO), and through which the substance had to penetrate (THROUGH). The procedure is therefore called the TO/THROUGH method. Detailed fault trees with 'release via ventilation' as the critical event (top event) were drawn. As a numerical example two initiating events from the KBS-II report were treated; 1. degassing of previously damaged pins (2 per year); 2. fall of a fully loaded rack (1 per year). If either of these events coincides with failure of the ventilation system radioactive dust (aerosol) can be released to the atmosphere. The probability for this and the amount of radioactivity released are estimated. (JIW)

Space biology research development

Science.gov (United States)

Bonting, Sjoerd L.

1993-01-01

The purpose of the Search for Extraterrestrial Intelligence (SETI) Institute is to conduct and promote research related activities regarding the search for extraterrestrial life, particularly intelligent life. Such research encompasses the broad discipline of 'Life in the Universe', including all scientific and technological aspects of astronomy and the planetary sciences, chemical evolution, the origin of life, biological evolution, and cultural evolution. The primary purpose was to provide funding for the Principal Investigator to collaborate with the personnel of the SETI Institute and the NASA-Ames Research center in order to plan and develop space biology research on and in connection with Space Station Freedom; to promote cooperation with the international partners in the space station; to conduct a study on the use of biosensors in space biology research and life support system operation; and to promote space biology research through the initiation of an annual publication 'Advances in Space Biology and Medicine'.

Assessment of workers' exposure to microorganisms when using biological degreasing stations.

Science.gov (United States)

Villeneuve, Carol-Anne; Marchand, Geneviève; Gardette, Marie; Lavoie, Jacques; Neesham-Grenon, Eve; Bégin, Denis; Debia, Maximilien

2018-06-01

Biological degreasing stations (BDSs) are used by mechanics. These BDSs use a water-based solution with a microbial degradation process. Occupational exposure during the use of BDSs has not been reported and few studies have identified the bacteria present. The objectives were to measure the concentration of microorganisms during BDSs' use and monitor the bacterial community in the liquid over time. Five mechanical workshops were studied. Six 30-min samples were taken at each workshop over one year. Bioaerosols in the ambient air samples were collected with Andersen impactors near the BDS Bioaerosols in the workers' breathing zone (WBZ) were collected on filters. Fresh bio-degreasing fluids were collected from unopened containers, and used bio-degreasing fluids were collected in the BDS. The results show that the use of BDSs does not seem to increase bioaerosols concentrations in the WBZ (concentrations lower than 480 CFU/m 3 ) and that the bacterial communities (mainly yeasts, Bacillus subtilis and Pseudomonas aeruginosa) in the bio-degreasing fluids change through time and differ from the original community (B. subtilis). This study established that workers using BDSs were exposed to low levels of bioaerosols. No respiratory protection is recommended based on bioaerosols concentrations, but gloves and strict personal hygiene practices are essential. Copyright © 2017 Elsevier Ltd. All rights reserved.

Accommodating life sciences on the Space Station

Science.gov (United States)

Arno, Roger D.

1987-01-01

The NASA Ames Research Center Biological Research Project (BRP) is responsible for identifying and accommodating high priority life science activities, utilizing nonhuman specimens, on the Space Station and is charged to bridge the gap between the science community and the Space Station Program. This paper discusses the approaches taken by the BRP in accomodating these research objectives to constraints imposed by the Space Station System, while maintaining a user-friendly environment. Consideration is given to the particular research disciplines which are given priority, the science objectives in each of these disciplines, the functions and activities required by these objectives, the research equipment, and the equipment suits. Life sciences programs planned by the Space Station participating partners (USA, Europe, Japan, and Canada) are compared.

Disposal of high active nuclear fuel waste. A critical review of the Nuclear Fuel Safety (KBS) project on final disposal of vitrified high active nuclear fuel waste

International Nuclear Information System (INIS)

1978-01-01

This report has been prepared by the Swedish Energy Commission's working group for Safety and Environment. The main contributions are by profs. Jan Rydberg of Chalmers University of Technology, Sweden and John W Winchester of Florida State University, USA. The aim of the report is to discuss weather the KBS-project fullfills the Swedish ''Stipulations Act'', that a absolutely safe way of disposing of the nuclear waste must have been demonstrated before any new reactors are allowed to be taken inot use. Rydberg and Winchester do not arrive at similar conclusions. (L.E.)

Development of the Plate Boundary Observatory GPS Low Latency Salton Trough Radio Network

Science.gov (United States)

Walls, C.; Miller, S.; Wilson, B.; Lawrence, S.; Arnitz, E.

2008-05-01

UNAVCO is developing a 20 GPS station low latency radio network that spans the San Andreas and San Jacinto faults in the region of highest strain in southern California and the narrowest part of the North America-Pacific plate boundary. The Salton Trough Radio Network (STRN) is instrumented with Ethernet bridge Intuicom EB6+ (900 MHz) radios to transmit a high rate low latency data stream from each permanent GPS site for the purpose of the following: 1) telemeter 15 second data (1 MB/day/station) to the Plate Boundary Observatory archive, 2) accommodate the timely download of 1 and 5 sample per second data following large earthquakes (4 MB/hour/station), and 3) test the UStream of 1Hz BINEX and RTCM data. Three of four phases have been completed. Office radio testing yielded transfer rates of 30-50 KB/s with subsecond latency while streaming 1 Hz data. Latency climbed to ~1.8 seconds while simultaneously streaming 1 Hz and downloading hourly 1 and 5 sample per second data files. Field testing demonstrated rates on the order of 30 KB/s. At present the radios are installed and have transfer rates of 10-40 KB/s between sites that span 10-32 km. The final phase will be the installation of the main telemetry relay where master radios will be connected to a high speed ISP near the town of Brawley. The high-rate low latency UStream data will be available to researchers who are developing prototype earthquake early warning systems in Southern California. A goal of the STRN is to make the data available rapidly enough for GPS-derived coseismic and dynamic displacements to be integrated into early warning system earthquake models. The improved earthquake models will better assist emergency response. UStream data will also aid surveyors who wish to use PBO GPS stations as permanent, high-quality base stations in real-time kinematic surveys.

Ada in AI or AI in Ada. On developing a rationale for integration

Science.gov (United States)

Collard, Philippe E.; Goforth, Andre

1988-01-01

The use of Ada as an Artificial Intelligence (AI) language is gaining interest in the NASA Community, i.e., by parties who have a need to deploy Knowledge Based-Systems (KBS) compatible with the use of Ada as the software standard for the Space Station. A fair number of KBS and pseudo-KBS implementations in Ada exist today. Currently, no widely used guidelines exist to compare and evaluate these with one another. The lack of guidelines illustrates a fundamental problem inherent in trying to compare and evaluate implementations of any sort in languages that are procedural or imperative in style, such as Ada, with those in languages that are functional in style, such as Lisp. Discussed are the strengths and weakness of using Ada as an AI language and a preliminary analysis provided of factors needed for the development of criteria for the integration of these two families of languages and the environments in which they are implemented. The intent for developing such criteria is to have a logical rationale that may be used to guide the development of Ada tools and methodology to support KBS requirements, and to identify those AI technology components that may most readily and effectively be deployed in Ada.

Should the Space Station be an ark?

Science.gov (United States)

Wassersug, R

1994-08-01

This essay explores the pros and cons of maximizing the number of species that can be maintained on the Space Station. It reviews some of the history of comparative space biology to show that different cultures have different perspectives on the study of non-traditional research organisms (ie non-rodents) in space. Despite these differences, there are simple principles that all international partners in the Space Station endeavour should be able to uphold when deciding what facilities to build and what species to fly. As an argument for maximizing the taxonomic diversity on the Space Station, examples are given to show how very similar organisms may have different reactions to microgravity. At the same time the political pressure in the USA to make the Space Station an institution specifically servicing the 'health, well-being and economic benefits of people on earth', is acknowledged. Ultimately the justification for what species will be on the Space Station should rest with the quality of the scientific questions being asked.

Developing design premises for a KBS-3V repository based on results from the safety assessment - 16027

International Nuclear Information System (INIS)

Andersson, Johan; Hedin, Allan

2009-01-01

As a part of the planned license application for a final repository for spent nuclear fuel the Swedish Nuclear Fuel and Waste Management Co. (SKB), has developed design premises from a long term safety aspect of a KBS-3V repository for spent nuclear fuel. The purpose is to provide requirements from a long term safety aspect, to form the basis for the development of the reference design of the repository and to justify that design. Design premises typically concern specification on what mechanical loads the barriers must withstand, restrictions on the composition of barrier materials or acceptance criteria for the various underground excavations. These design constraints, if all fulfilled by the actual design, should form a good basis for demonstrating repository safety. The justification for these design premises is derived from SKB's most recent safety assessment SR-Can complemented by a few additional analyses. Some of the design premises may be modified in future stages of SKB's program, as a result of analyses based on more detailed site data and a more developed understanding of processes of importance for long-term safety. (authors)

Risk perception and occupational accidents: a study of gas station workers in southern Brazil.

Science.gov (United States)

Cezar-Vaz, Marta Regina; Rocha, Laurelize Pereira; Bonow, Clarice Alves; Silva, Mara Regina Santos da; Vaz, Joana Cezar; Cardoso, Letícia Silveira

2012-07-01

The present study aimed to identify the perceptions of gas station workers about physical, chemical, biological and physiological risk factors to which they are exposed in their work environment; identify types of occupational accidents involving gas station workers and; report the development of a socioenvironmental intervention as a tool for risk communication to gas station workers. A quantitative study was performed with 221 gas station workers in southern Brazil between October and December 2010. Data collection was performed between October to December 2010 via structured interviews. The data were analyzed using SPSS 19.0. The participants identified the following risk types: chemical (93.7%), physical (88.2%), physiological (64.3%) and biological (62.4%). In this sample, 94.1% of gas station workers reported occupational accidents, and 74.2% reported fuel contact with the eyes (p accidents as an indicator of the dangerous nature of their work environment.

Biological and radioecological investigations at the Ringhals nuclear power station, 1968-1987

International Nuclear Information System (INIS)

Grimaas, U.; Jacobsson, A.; Neuman, E.

1989-09-01

The summary is based on 19 papers, which are presented in the References. The reports concern fish, bottom-living animals, zooplankton and algae as well as the presence of radioactivity in the aquatic and terrestrial environments. The investigation has been conducted at the request of Vaesterbygden's Water Rights Court and present the experiences of twelve operational years, of which the last four years have been with the power station at full capacity. In judging the effects of the operation of the power station, particular emphasis has been placed on questions given priority by the Water Rights Court, namely fishing and radioactivity. As regards fishing, the direct effects of the cooling-system on fish in different developmental stages have been assessed to be of importance. Water-borne radioactivity has been traced in organisms and sediment in the area. The concentrations of different radionucleids originating from the power station are highest in algae and lowest in fish-meat. The results form the basis of calculations of the radioactive dose to man. (orig./HP)

An evaluation of repository-induced disturbances for a KBS-3 type repository

Energy Technology Data Exchange (ETDEWEB)

Savage, D.; McLeod, R.; McEwen, T. [QuantiSci, Melton Mowbray (United Kingdom)

1998-03-01

This report considers the potential physical and chemical perturbations caused by the excavation, operation and backfilling and sealing of a KBS-3 type repository for spent fuel in Sweden. Parts of the underground excavations are likely to remain open to the atmosphere for up to several decades. Time-dependent changes to the chemical environment and the properties of the geological formation will be occurring as well as the initial disturbance of construction and subsequent changes after backfilling. In addition, this report also discusses issues that arise from the co-disposal of spent fuel and intermediate level waste. The processes which are likely to act during each stage of a repository from construction through to backfilling and sealing have been reviewed and the degree to which these processes are understood and represented within the performance assessment is discussed. The areas of particular interest are: The coupling of thermal, hydrogeological and mechanical processes with particular reference to the development of the near-field; Understanding the transient process of re-saturation with particular reference to the buffer material surrounding the waste canisters, including chemical changes to the material; The impact of accidental events during the construction and operational phases of work and their possible consequence on the long term performance of the repository; Chemical issues relating to the co-disposal of spent fuel and intermediate level wastes within a single facility. When consideration of transient processes and coupling is discussed, it is apparent that numerical tools and a complete understanding to provide quantitative information is lacking. The importance of the engineered barrier system within the performance assessment for spent fuel disposal is recognised and the emphasis is placed on the understanding of the coupled processes in the evolution in the near-field of the geosphere 45 refs, 4 fig, 2 tabs

An evaluation of repository-induced disturbances for a KBS-3 type repository

International Nuclear Information System (INIS)

Savage, D.; McLeod, R.; McEwen, T.

1998-03-01

This report considers the potential physical and chemical perturbations caused by the excavation, operation and backfilling and sealing of a KBS-3 type repository for spent fuel in Sweden. Parts of the underground excavations are likely to remain open to the atmosphere for up to several decades. Time-dependent changes to the chemical environment and the properties of the geological formation will be occurring as well as the initial disturbance of construction and subsequent changes after backfilling. In addition, this report also discusses issues that arise from the co-disposal of spent fuel and intermediate level waste. The processes which are likely to act during each stage of a repository from construction through to backfilling and sealing have been reviewed and the degree to which these processes are understood and represented within the performance assessment is discussed. The areas of particular interest are: The coupling of thermal, hydrogeological and mechanical processes with particular reference to the development of the near-field; Understanding the transient process of re-saturation with particular reference to the buffer material surrounding the waste canisters, including chemical changes to the material; The impact of accidental events during the construction and operational phases of work and their possible consequence on the long term performance of the repository; Chemical issues relating to the co-disposal of spent fuel and intermediate level wastes within a single facility. When consideration of transient processes and coupling is discussed, it is apparent that numerical tools and a complete understanding to provide quantitative information is lacking. The importance of the engineered barrier system within the performance assessment for spent fuel disposal is recognised and the emphasis is placed on the understanding of the coupled processes in the evolution in the near-field of the geosphere

Risk Perception and Occupational Accidents: A Study of Gas Station Workers in Southern Brazil

OpenAIRE

Cezar-Vaz, Marta Regina; Rocha, Laurelize Pereira; Bonow, Clarice Alves; da Silva, Mara Regina Santos; Vaz, Joana Cezar; Cardoso, Letícia Silveira

2012-01-01

The present study aimed to identify the perceptions of gas station workers about physical, chemical, biological and physiological risk factors to which they are exposed in their work environment; identify types of occupational accidents involving gas station workers and; report the development of a socioenvironmental intervention as a tool for risk communication to gas station workers. A quantitative study was performed with 221 gas station workers in southern Brazil between October and Decem...

Herpetofauna of the Beni Biological Station Biosphere Reserve, Amazonian Bolivia: Additional information, and current knowledge in context

Science.gov (United States)

Middendorf, G.; Reynolds, R.; Herrera-MacBryde, Olga; Dallmeier, Francisco; MacBryde, Bruce; Cominskey, James A.; Miranda, Carmen

2000-01-01

Previous collections in the Departamento del Beni in tropical Bolivia only hinted at high levels of herpetological biodiversity (Fugler 1986, 1988; de la Riva 1990a; Fugler and de la Riva 1990). Fieldwork (totaling 48 days) in July-August 1988 and September 1987 (dry seasons) and November-December 1990 (wet season) has resulted in collection and identification of 401 amphibian and reptilian specimens from the general area of the Beni Biological Station's (EBB) headquarters at El Porvenir. These collections represent 33 amphibian and 17 reptilian species in 29 genera (14 amphibian, 15 reptilian). The inventory of herpetofauna scientifically documented to occur in the Departamento del Beni is considered to have been increased by 6 amphibian and 10 reptilian species. Specimens that could not be definitively identified (reflecting taxonomic uncertainty and/or probably species new to science) include 3 amphibian species (anurans) and 2 reptilian species (snakes). The EBB harbors the richest savanna for anuran species known in South America.

Risk Perception and Occupational Accidents: A Study of Gas Station Workers in Southern Brazil

Directory of Open Access Journals (Sweden)

Letícia Silveira Cardoso

2012-07-01

Full Text Available The present study aimed to identify the perceptions of gas station workers about physical, chemical, biological and physiological risk factors to which they are exposed in their work environment; identify types of occupational accidents involving gas station workers and; report the development of a socioenvironmental intervention as a tool for risk communication to gas station workers. A quantitative study was performed with 221 gas station workers in southern Brazil between October and December 2010. Data collection was performed between October to December 2010 via structured interviews. The data were analyzed using SPSS 19.0. The participants identified the following risk types: chemical (93.7%, physical (88.2%, physiological (64.3% and biological (62.4%. In this sample, 94.1% of gas station workers reported occupational accidents, and 74.2% reported fuel contact with the eyes (p < 0.05. It is concluded that workers perceive risks, and that they tend to relate risks with the occurrence of occupational accidents as an indicator of the dangerous nature of their work environment.

Long-term safety for KBS-3 repositories at Forsmark and Laxemar - a first evaluation. Main Report of the SR-Can project

International Nuclear Information System (INIS)

Hedin, Allan

2006-10-01

This document is the main report from the safety assessment project SR-Can. The SR-Can project is a preparatory stage for the SR-Site assessment, the report that will be used in support of SKB's application for a final repository. The purposes of the safety assessment SR-Can are the following: 1. To make a first assessment of the safety of potential KBS-3 repositories at Forsmark and Laxemar to dispose of canisters as specified in the application for the encapsulation plant. 2. To provide feedback to design development, to SKB's RandD programme, to further site investigations and to future safety assessment projects. 3. To foster a dialogue with the authorities that oversee SKB's activities, i.e. the Swedish Nuclear Power Inspectorate, SKI, and the Swedish Radiation Protection Authority, SSI, regarding interpretation of applicable regulations, as a preparation for the SR-Site project. The assessment relates to the KBS-3 disposal concept in which copper canisters with a cast iron insert containing spent nuclear fuel are surrounded by bentonite clay and deposited at approximately 500 m depth in saturated, granitic rock. Preliminary data from the Forsmark and Laxemar sites, presently being investigated by SKB as candidates for a KBS-3 repository are used in the assessment. An important aim of this report is to demonstrate the proper handling of requirements placed on the safety assessment in applicable regulations. Therefore, regulations issued by the Swedish Nuclear Power Inspectorate and the Swedish Radiation Protection Institute are reproduced in an Appendix where references are given to sections in the main text where the handling of the different requirements is discussed. The principal acceptance criterion requires that 'the annual risk of harmful effects after closure does not exceed 10 -6 for a representative individual in the group exposed to the greatest risk'. 'Harmful effects' refer to cancer and hereditary effects. The risk limit corresponds to an

Long-term safety for KBS-3 repositories at Forsmark and Laxemar - a first evaluation. Main Report of the SR-Can project

Energy Technology Data Exchange (ETDEWEB)

Hedin, Allan (ed.)

2006-10-15

This document is the main report from the safety assessment project SR-Can. The SR-Can project is a preparatory stage for the SR-Site assessment, the report that will be used in support of SKB's application for a final repository. The purposes of the safety assessment SR-Can are the following: 1. To make a first assessment of the safety of potential KBS-3 repositories at Forsmark and Laxemar to dispose of canisters as specified in the application for the encapsulation plant. 2. To provide feedback to design development, to SKB's RandD programme, to further site investigations and to future safety assessment projects. 3. To foster a dialogue with the authorities that oversee SKB's activities, i.e. the Swedish Nuclear Power Inspectorate, SKI, and the Swedish Radiation Protection Authority, SSI, regarding interpretation of applicable regulations, as a preparation for the SR-Site project. The assessment relates to the KBS-3 disposal concept in which copper canisters with a cast iron insert containing spent nuclear fuel are surrounded by bentonite clay and deposited at approximately 500 m depth in saturated, granitic rock. Preliminary data from the Forsmark and Laxemar sites, presently being investigated by SKB as candidates for a KBS-3 repository are used in the assessment. An important aim of this report is to demonstrate the proper handling of requirements placed on the safety assessment in applicable regulations. Therefore, regulations issued by the Swedish Nuclear Power Inspectorate and the Swedish Radiation Protection Institute are reproduced in an Appendix where references are given to sections in the main text where the handling of the different requirements is discussed. The principal acceptance criterion requires that 'the annual risk of harmful effects after closure does not exceed 10{sup -6} for a representative individual in the group exposed to the greatest risk'. 'Harmful effects' refer to cancer and hereditary effects

Modelling of long term geochemical evolution and study of mechanical perturbation of bentonite buffer of a KBS-3 repository

Energy Technology Data Exchange (ETDEWEB)

Marsal, Francois; Pellegrini, Delphine; Deleruyelle, Frederic; Serres, Christophe (French Inst. for Radiological Protection and Nuclear Safety (IRSN), Fontenay-aux-Roses (FR)); Windt, Laurent de (Ecole des Mines de Paris, Paris (FR))

2008-03-15

PART I: The Swedish Nuclear Fuel and Waste Management Co. (SKB) has recently completed a safety assessment project named SR-Can, related to the KBS-3 disposal concept. In this concept, the waste packages are surrounded by a buffer made of either MX-80 or Deponit CA-N bentonite. Interactions between the buffer and groundwater may modify the buffer composition and thus its containment properties. The Swedish Radiation Protection Authorities (SSI) requested the French Institute for Radiological Protection and Nuclear Safety (IRSN) to perform the present study in support of SSI review of the SR-Can report. The purpose is to assess the geochemical evolution of both potential buffer materials due to the intrusion of different types of groundwater, with a similar modelling layout to that reported in SR-Can and detailed in Arcos et al. Three main categories of water inflows via a fracture intersecting a deposition hole are considered: the Forsmark reference groundwater, a high-salinity groundwater to account for up-rise of deep-seated brines and a diluted water representing ice-melting derived-groundwater. In addition to this, the redox buffering capacity of Deponit CA-N bentonite and the thermal effect on MX-80 bentonite geochemistry have been assessed. This modelling work has been performed using the reactive transport modelling code HYTEC. The main outcome of the present study is that the intrusion of the considered groundwaters should not affect drastically the geochemistry of neither the Deponit CA-N nor the MX-80 bentonite on the longterm (100,000 y). Bentonite pH may reach high values (up to 10.5) in some cases but does not reach SKB criterion value related to bentonite chemical stability. Dissolution-precipitation of accessory minerals is not significant enough to induce important porosity changes (rise by maximum 2 %). Globally, the montmorillonite exchanger undergoes Na by Ca partial replacement, which may decrease the swelling pressure of the bentonite. The

[Danger of cellular telephones and their relay stations].

Science.gov (United States)

Santini, R; Seigne, M; Bonhomme-Faivre, L

2000-07-01

Cellular phones and their base stations emit pulsed microwaves in the environment. Cellular phone users are exposed in the near field and, under this condition, a large part of the electromagnetic energy is absorbed by the head, leading to an increased brain temperature. The general population is exposed under far field conditions to an electromagnetic intensity depending on the distance from the base station, passive re-emitters, the number of communications maintained by the base station and their position in relation to antennae (in front of the antenna or behind). Biological effects have been reported, such as radiofrequency sickness, electroencephalographic and blood pressure changes and also cancer risks in humans and animals exposed to microwave irradiation. Some European countries (Italy, France, Belgium, etc.) have taken measures to protect their populations.

(Case Study: Wastewater Pump Station of Khoramabad

Directory of Open Access Journals (Sweden)

Masoud Taheriyoun

2014-10-01

Full Text Available Evaluation of a Biofilter System for Removal of Hydrogen Sulfide Gas (Case Study: Wastewater Pump Station of Khorramabad Abstract The biofilter system is one of the methods commonly used for the removal of hydrogen sulfide as the main source of odors emitted from wastewater facilities. The system is based on using the contaminant material as bedding to feed microorganisms. To achieve the desirable removal efficiency, it is, therefore, essential to create the proper conditions for the bacteria to grow on the bedding. In this study, a pilot-scale biofilter made of compost and woodchip (with a compost/woodchip ratio of 5:1 was used as the bedding material at Khorrmabad wastewater pumping station to investigate the performance of the system under real conditions. The experiment was carried out over 75 days during which time the input and output H2S concentrations were measured on a regular basis. Moisture was adjusted between 40% and 60% throughout the experiment to provide optimal conditions for bacterial growth. The results showed that the concentration of H2S emitted from the pumping station during 24 hours varied greatly between 0 and 48 PPM. The maximum adsorption capacity of the biological bedding was recorded at 2.874 g/m3.hr and the mean efficiency of H2S removal including the startup time was 89%. The mean performance efficiency during the biological activity after the startup was recorded at 98%.

Consequences of using crushed crystalline rock as ballast in KBS-3 tunnels instead of rounded quartz particles

Energy Technology Data Exchange (ETDEWEB)

Push, R [Clay Technology AB (Sweden)

1995-02-01

The basic question has been whether such replacement alters the hydraulic conductivity and compressibility as well as expandability and also if the physical and chemical stabilities are altered. The key factor is the microstructural constitution of the bentonite/ballast mixtures, which is primarily controlled by the grain size distribution of the ballast. The compact ability of backfills with quartz sand (SB) is higher than that of backfills with crushed rock as ballast (RB). The physical stability of RB backfills in terms of piping and erosion resistance will be somewhat lower than that of SB backfills. The chemical stability is practically independent of whether the ballast is pure quartz or rock with K-bearing minerals because the temperature in the backfill will be too low to yield significant smectite to illite conversion in the short heating period. In order to reach the same densities of SB and RB backfills, which turn out to give fairly similar physical properties, the latter backfills need more effective compaction or, alternatively, a higher bentonite content. It is estimated that if the bentonite content in RB backfills is not increased while the density is enhanced to what is achievable, these backfills will serve equally well as SB backfills with the densities implied by the basic KBS-3 concept. 23 refs, 27 figs, 7 tabs.

Consequences of using crushed crystalline rock as ballast in KBS-3 tunnels instead of rounded quartz particles

International Nuclear Information System (INIS)

Push, R.

1995-02-01

The basic question has been whether such replacement alters the hydraulic conductivity and compressibility as well as expandability and also if the physical and chemical stabilities are altered. The key factor is the microstructural constitution of the bentonite/ballast mixtures, which is primarily controlled by the grain size distribution of the ballast. The compact ability of backfills with quartz sand (SB) is higher than that of backfills with crushed rock as ballast (RB). The physical stability of RB backfills in terms of piping and erosion resistance will be somewhat lower than that of SB backfills. The chemical stability is practically independent of whether the ballast is pure quartz or rock with K-bearing minerals because the temperature in the backfill will be too low to yield significant smectite to illite conversion in the short heating period. In order to reach the same densities of SB and RB backfills, which turn out to give fairly similar physical properties, the latter backfills need more effective compaction or, alternatively, a higher bentonite content. It is estimated that if the bentonite content in RB backfills is not increased while the density is enhanced to what is achievable, these backfills will serve equally well as SB backfills with the densities implied by the basic KBS-3 concept. 23 refs, 27 figs, 7 tabs

Temporal and spatial patterns of anthropogenic disturbance at McMurdo Station, Antarctica

International Nuclear Information System (INIS)

Kennicutt, Mahlon C II; Klein, Andrew; Montagna, Paul; Palmer, Terence; Sweet, Stephen; Wade, Terry; Sericano, Jose; Denoux, Guy

2010-01-01

Human visitations to Antarctica have increased in recent decades, raising concerns about preserving the continent's environmental quality. To understand the spatial and temporal patterns of anthropogenic disturbances at the largest scientific station in Antarctica, McMurdo Station, a long-term monitoring program has been implemented. Results from the first nine years (1999-2007) of monitoring are reported. Most physical disturbance of land surfaces occurred prior to 1970 during initial establishment of the station. Hydrocarbons from fuel and anthropogenic metals occur in patches of tens to hundreds of square meters in areas of fuel usage and storage. Most soil contaminant concentrations are not expected to elicit biological responses. Past disposal practices have contaminated marine sediments with polychlorinated biphenyls (PCBs), petroleum hydrocarbons, and metals in close proximity to the station that often exceed concentrations expected to elicit biological responses. Chemical contamination and organic enrichment reduced marine benthic ecological integrity within a few hundred meters offshore of the station. Contaminants were detected in marine benthic organisms confirming bioavailability and uptake. PCBs in sediments are similar to suspected source materials, indicating minimal microbial degradation decades after release. Anthropogenic disturbance of the marine environment is likely to persist for decades. A number of monitoring design elements, indicators and methodologies used in temperate climates were effective and provide guidance for monitoring programs elsewhere in Antarctica.

Impact of corrosion-derived iron on the bentonite buffer within the KBS-3H disposal concept. The Olkiluoto site as case study

International Nuclear Information System (INIS)

Wersin, Paul; Birgersson, Martin; Olsson, Siv; Karnland, Ola; Snellman, Margit

2008-05-01

Steel components are unstable in EBS environments. They will corrode to fairly insoluble corrosion products, such as magnetite, and also react with the smectitic matrix of the bentonite buffer. In this study, the impact of reduced iron on the buffer's stability has been assessed within the framework of the KBS-H concept. Our work includes two parts. In the first part, available data from experimental and modelling studies have been compiled and interpreted. In the second part, a relatively simple geochemical modelling exercise on the iron-bentonite interaction in the current KBS-3H disposal system has been performed using Olkiluoto as test case. The iron in this case stems from the perforated supercontainer steel shell foreseen to be emplaced around the buffer material. The iron-bentonite interaction under reducing conditions may involve different processes including sorption, redox and dissolution/precipitation reactions, the details of which are not yet understood. One process to consider is the sorption of corrosion-derived Fe(II). This process is fast and leads to strong binding of Fe(II) at the smectite surface. Whether this sorption reaction is accompanied by a redox and surface precipitation reaction is presently not clear. A further process to consider under very reducing conditions is the reduction of structural Fe(III) in the clay which may destabilise the montmorillonite structure. The process of greatest relevance for the buffer's performance is montmorillonite transformation in contact with reduced iron. This process is very slow and experimentally difficult to investigate. Current data suggest that the transformation process may either lead to a Fe-rich smectite (e.g. saponite) or to a non-swelling clay (berthierine or chlorite). In addition, cementation due to precipitation of iron corrosion products or of SiO 2 resulting from montmorillonite transformation may occur. Physical properties of the buffer may in principle be affected by montmorillonite

Impact of corrosion-derived iron on the bentonite buffer within the KBS-3H disposal concept. The Olkiluoto site as case study

Energy Technology Data Exchange (ETDEWEB)

Wersin, Paul (National Cooperative for the Disposal of Radioactive Waste, Nagra, Wettingen (Switzerland)); Birgersson, Martin; Olsson, Siv; Karnland, Ola (Clay Technology AB, Lund (Sweden)); Snellman, Margit (Saanio and Riekkola Oy, Helsinki (Finland))

2008-05-15

Steel components are unstable in EBS environments. They will corrode to fairly insoluble corrosion products, such as magnetite, and also react with the smectitic matrix of the bentonite buffer. In this study, the impact of reduced iron on the buffer's stability has been assessed within the framework of the KBS-H concept. Our work includes two parts. In the first part, available data from experimental and modelling studies have been compiled and interpreted. In the second part, a relatively simple geochemical modelling exercise on the iron-bentonite interaction in the current KBS-3H disposal system has been performed using Olkiluoto as test case. The iron in this case stems from the perforated supercontainer steel shell foreseen to be emplaced around the buffer material. The iron-bentonite interaction under reducing conditions may involve different processes including sorption, redox and dissolution/precipitation reactions, the details of which are not yet understood. One process to consider is the sorption of corrosion-derived Fe(II). This process is fast and leads to strong binding of Fe(II) at the smectite surface. Whether this sorption reaction is accompanied by a redox and surface precipitation reaction is presently not clear. A further process to consider under very reducing conditions is the reduction of structural Fe(III) in the clay which may destabilise the montmorillonite structure. The process of greatest relevance for the buffer's performance is montmorillonite transformation in contact with reduced iron. This process is very slow and experimentally difficult to investigate. Current data suggest that the transformation process may either lead to a Fe-rich smectite (e.g. saponite) or to a non-swelling clay (berthierine or chlorite). In addition, cementation due to precipitation of iron corrosion products or of SiO{sub 2} resulting from montmorillonite transformation may occur. Physical properties of the buffer may in principle be affected by

Radioecological investigations of the Bilibino Nuclear Power Station area

Energy Technology Data Exchange (ETDEWEB)

Emelyanova, L.; Neretin, L. [Moscow State Univ. (Russian Federation). Geographical Faculty]|[Russian Academy of Sciences, Moscow (Russian Federation). P.P. Shirshov Inst. of Oceanology

1995-12-31

The landscape structure of the territory and the current radioactive state of ecosystems in the vicinity of Bilibino Nuclear Power Station (Western Chukotka Peninsula) within the area of its potential influence on the environment were studied in 1989--1990. Accumulation of strontium-90 and cesium-137 radionuclides in several key biological members of the ecosystems has been analyzed. Maximal weighted content of cesium-137 was revealed in mountain pine cones (Pinus pumila) -- 9,200 Bq/kg.d.w., cowberry fruits have demonstrated considerable contamination by strontium and cesium isotopes. The purification of first two components of food chain ``lichen-reindeer-man`` was pointed out in the investigated area. Besides the chemical characteristics, visual biological anomalies of biocomponents nearby the Bilibino NPS ecosystems are observed. On the basis of field radioecological investigations and future work, programs were developed for the conditions of the Bilibino Nuclear Power Station area. This experience could be applied to the researches of radioactive contamination in ecosystems of other northern territories.

Plio-Pleistocene facies environments from the KBS Member, Koobi Fora Formation: implications for climate controls on the development of lake-margin hominin habitats in the northeast Turkana Basin (northwest Kenya).

Science.gov (United States)

Lepre, Christopher J; Quinn, Rhonda L; Joordens, Josephine C A; Swisher, Carl C; Feibel, Craig S

2007-11-01

Climate change is hypothesized as a cause of major events of Plio-Pleistocene East African hominin evolution, but the vertically discontinuous and laterally confined nature of the relevant geological records has led to difficulties with assessing probable links between the two. High-resolution sedimentary sequences from lacustrine settings can provide comprehensive data of environmental changes and detailed correlations with well-established orbital and marine records of climate. Hominin-bearing deposits from Koobi Fora Ridge localities in the northeast Turkana Basin of Kenya are an archive of Plio-Pleistocene lake-margin sedimentation though significant developmental junctures of northern African climates, East African environments, and hominin evolution. This study examines alluvial channel and floodplain, nearshore lacustrine, and offshore lacustrine facies environments for the approximately 136-m-thick KBS Member (Koobi Fora Formation) exposed at the Koobi Fora Ridge. Aspects of the facies environments record information on the changing hydrosedimentary dynamics of the lake margin and give insights into potential climatic controls. Seasonal/yearly climate changes are represented by the varve-like laminations in offshore mudstones and the slickensides, dish-shaped fractures, and other paleosol features overprinted on floodplain strata. Vertical shifts between facies environments, however, are interpreted to indicate lake-level fluctuations deriving from longer-term, dry-wet periods in monsoonal rainfall. Recurrence periods for the inferred lake-level changes range from about 10,000 to 50,000 years, and several are consistent with the average estimated timescales of orbital precession ( approximately 20,000 years) and obliquity ( approximately 40,000 years). KBS Member facies environments from the Koobi Fora Ridge document the development of lake-margin hominin habitats in the northeast Turkana Basin. Environmental changes in these habitats may be a result of

33-Foot-Diameter Space Station Leading to Space Base

Science.gov (United States)

1969-01-01

This picture illustrates a concept of a 33-Foot-Diameter Space Station Leading to a Space Base. In-house work of the Marshall Space Flight Center, as well as a Phase B contract with the McDornel Douglas Astronautics Company, resulted in a preliminary design for a space station in 1969 and l970. The Marshall-McDonnel Douglas approach envisioned the use of two common modules as the core configuration of a 12-man space station. Each common module was 33 feet in diameter and 40 feet in length and provided the building blocks, not only for the space station, but also for a 50-man space base. Coupled together, the two modules would form a four-deck facility: two decks for laboratories and two decks for operations and living quarters. Zero-gravity would be the normal mode of operation, although the station would have an artificial gravity capability. This general-purpose orbital facility was to provide wide-ranging research capabilities. The design of the facility was driven by the need to accommodate a broad spectrum of activities in support of astronomy, astrophysics, aerospace medicine, biology, materials processing, space physics, and space manufacturing. To serve the needs of Earth observations, the station was to be placed in a 242-nautical-mile orbit at a 55-degree inclination. An Intermediate-21 vehicle (comprised of Saturn S-IC and S-II stages) would have launched the station in 1977.

Knowledge-based system for flight information management. Thesis

Science.gov (United States)

Ricks, Wendell R.

1990-01-01

The use of knowledge-based system (KBS) architectures to manage information on the primary flight display (PFD) of commercial aircraft is described. The PFD information management strategy used tailored the information on the PFD to the tasks the pilot performed. The KBS design and implementation of the task-tailored PFD information management application is described. The knowledge acquisition and subsequent system design of a flight-phase-detection KBS is also described. The flight-phase output of this KBS was used as input to the task-tailored PFD information management KBS. The implementation and integration of this KBS with existing aircraft systems and the other KBS is described. The flight tests are examined of both KBS's, collectively called the Task-Tailored Flight Information Manager (TTFIM), which verified their implementation and integration, and validated the software engineering advantages of the KBS approach in an operational environment.

Some environmental effects of emissions from CANDU nuclear generating stations and heavy water plants

International Nuclear Information System (INIS)

Effer, W.R.

Non-radioactive releases during normal operation of Ontario Hydro's nuclear generating stations and heavy water plants are summarized and related to existing regulations and guidelines. Low-grade heat in the circulating cooling water discharge is the most important of the non-radioactive effluents. Some of the hydrological, biological and water quality aspects of thermal discharges are discussed in relation to the operation of Ontario Hydro's thermal generating stations on the Great Lakes. Chemical releases to air or water include chlorine, hydrogen sulphide, water treatment plant effluents, oily waste water and sewage lagoon effluents. The significance of the first two of these releases to the environment is reviewed, particularly in relation to Great Lakes water quality and biological concerns. (author)

Biological investigations off the Oskarshamn nuclear power station during the 1980's

International Nuclear Information System (INIS)

Neuman, E.; Andersson, J.

1990-11-01

The Oscarshamn power station consists of three nuclear reactors, of which the first came into production in 1972 and the last in 1985. The power station uses large volumes of cooling-water; altogether 100 m 3 /s is heated 10 degrees C. During the 1970's, the investigations of the ecological effects of the use of cooling-water had a wide coverage, whereas during the 1980's, the years treated here, the investigations have mainly been concentrated on fish and bottom fauna. The temperature increase stimulates growth of many organisms and causes attraction. The cooling-water plume and the counter-currents it causes increase the transports of nutrients. The concentration of nutrients in different ways contributes to increased production further up in the food chains and strengthens the attraction of fish. The losses of fish in the cooling system have been relatively small. The parasitization frequency of eels in the receiving bay is extremely high, but otherwise there have been no abnormal disease or parasite attacks. Disturbances to the reproduction of fish in the heated water are present. The importance of this, particularly for surrounding areas, should be investigated within the continued monitoring. (authors)

The SNS target station preliminary Title I shielding analyses

International Nuclear Information System (INIS)

Johnson, J.O.; Santoro, R.T.; Lillie, R.A.; Barnes, J.M.; McNeilly, G.S.

2000-01-01

The Department of Energy (DOE) has given the Spallation Neutron Source (SNS) project approval to begin Title I design of the proposed facility to be built at Oak Ridge National Laboratory (ORNL). During the conceptual design phase of the SNS project, the target station bulk-biological shield was characterized and the activation of the major targets station components was calculated. Shielding requirements were assessed with respect to weight, space, and dose-rate constraints for operating, shut-down, and accident conditions utilizing the SNS shield design criteria, DOE Order 5480.25, and requirements specified in 10 CFR 835. Since completion of the conceptual design phase, there have been major design changes to the target station as a result of the initial shielding and activation analyses, modifications brought about due to engineering concerns, and feedback from numerous external review committees. These design changes have impacted the results of the conceptual design analyses, and consequently, have required a re-investigation of the new design. Furthermore, the conceptual design shielding analysis did not address many of the details associated with the engineering design of the target station. In this paper, some of the proposed SNS target station preliminary Title I shielding design analyses will be presented. The SNS facility (with emphasis on the target station), shielding design requirements, calculational strategy, and source terms used in the analyses will be described. Preliminary results and conclusions, along with recommendations for additional analyses, will also be presented. (author)

Impact of corrosion-derived iron on the bentonite buffer within the KBS-3H disposal concept. The Olkiluoto site as case study

Energy Technology Data Exchange (ETDEWEB)

Wersin, P. (Gruner AG, Basel (Switzerland)); Birgersson, M.; Olsson, S.; Karnland, O. (Clay Technology, Lund (Sweden)); Snellman, M. (Saanio and Riekkola Oy, Helsinki (Finland))

2007-12-15

Steel components are unstable in EBS (Engineered Barrier System) environments. They will corrode to fairly insoluble corrosion products, such as magnetite, and also react with the smectitic matrix of the bentonite buffer. In this study, the impact of reduced iron on the buffer's stability has been assessed within the framework of the KBS-H concept. Our work includes two parts. In the first part, available data from experimental and modelling studies have been compiled and interpreted. In the second part, a relatively simple geochemical modelling exercise on the iron-bentonite interaction in the current KBS-3H disposal system has been performed using Olkiluoto as test case. The iron in this case stems from the perforated supercontainer steel shell foreseen to be emplaced around the buffer material. The iron-bentonite interaction under reducing conditions may involve different processes including sorption, redox and dissolution / precipitation reactions, the details of which are not yet understood. One process to consider is the sorption of corrosion-derived Fe(II). This process is fast and leads to strong binding of Fe(II) at the smectite surface. Whether this sorption reaction is accompanied by a redox and surface precipitation reaction is presently not clear. A further process to consider under very reducing conditions is the reduction of structural Fe(III) in the clay which may destabilise the montmorillonite structure. The process of greatest relevance for the buffer's performance is montmorillonite transformation in contact with reduced iron. This process is very slow and experimentally difficult to investigate. Current data suggest that the transformation process may either lead to a Fe-rich smectite (e.g. saponite) or to a non-swelling clay (berthierine or chlorite). In addition, cementation due to precipitation of iron corrosion products or of SiO{sub 2} resulting from montmorillonite transformation may occur. Physical properties of the buffer may

Impact of corrosion-derived iron on the bentonite buffer within the KBS-3H disposal concept. The Olkiluoto site as case study

International Nuclear Information System (INIS)

Wersin, P.; Birgersson, M.; Olsson, S.; Karnland, O.; Snellman, M.

2007-12-01

Steel components are unstable in EBS (Engineered Barrier System) environments. They will corrode to fairly insoluble corrosion products, such as magnetite, and also react with the smectitic matrix of the bentonite buffer. In this study, the impact of reduced iron on the buffer's stability has been assessed within the framework of the KBS-H concept. Our work includes two parts. In the first part, available data from experimental and modelling studies have been compiled and interpreted. In the second part, a relatively simple geochemical modelling exercise on the iron-bentonite interaction in the current KBS-3H disposal system has been performed using Olkiluoto as test case. The iron in this case stems from the perforated supercontainer steel shell foreseen to be emplaced around the buffer material. The iron-bentonite interaction under reducing conditions may involve different processes including sorption, redox and dissolution / precipitation reactions, the details of which are not yet understood. One process to consider is the sorption of corrosion-derived Fe(II). This process is fast and leads to strong binding of Fe(II) at the smectite surface. Whether this sorption reaction is accompanied by a redox and surface precipitation reaction is presently not clear. A further process to consider under very reducing conditions is the reduction of structural Fe(III) in the clay which may destabilise the montmorillonite structure. The process of greatest relevance for the buffer's performance is montmorillonite transformation in contact with reduced iron. This process is very slow and experimentally difficult to investigate. Current data suggest that the transformation process may either lead to a Fe-rich smectite (e.g. saponite) or to a non-swelling clay (berthierine or chlorite). In addition, cementation due to precipitation of iron corrosion products or of SiO 2 resulting from montmorillonite transformation may occur. Physical properties of the buffer may in principle be

Biological reduction of dust nuisance on power station waste dumps

Energy Technology Data Exchange (ETDEWEB)

Kozel, J

1978-01-01

The results of pot trials and succeeding field trials carried out in 1966-72 to find out the best method of reclamationand stabilishing the fly ash and cinder waste dump at the Melnik power station are summarised. The material consists mainly of fine particles with a size range of less than 1 micron to 0.16 mm in diam., and creates a source of blown dust in dry weather. Treatment of the waste material before sowing grass and legume species, the species tested, sowing rates, applied fertilizers, irrigation and treatment of the resulting swards are discussed. The most suitable species were Festuca rubra, F. ovina, perennial ryegrass and Italian ryegrass; the cost of stabilising the dump was lowest with Italian ryegrass. (In English)

Environmental radioactivity at Machu Picchu Scientific Station

Energy Technology Data Exchange (ETDEWEB)

Gonzales, S; Osores, J; Jara, R [Direccion General de Seguridad Radiologica, Instituto Peruano de Energia Nuclear, Lima (Peru)

1998-07-01

Studies on environmental radioactivity at the Peruvian Scientific Station were carried out in the last two austral summer periods. The main objective of this study is to establish an environmental radiological monitoring program for evaluating environmental components and achieving a baseline study related to artificial and natural radioactivity levels. For this purpose, samples such as seaweeds, mosses, lichens, soil seawater, ice, marine sediment and underground water were collected from the area surrounding the station starting from Punta Crepin to Playa Inca and Playa Naylamp; then they were pre-conditioned in Machu Picchu Station and were sent to the Environmental Radioactivity laboratory of 'Racso' Peruvian Nuclear Center to conduct beta and gamma spectrometry. The Obtained results showed the presence of Cs-137 in geological components (soil and sediment) and in biological components (lichens and mosses). Nevertheless, those levels seem to be in a range of normal fluctuations after atmospheric nuclear testing and they are not considered to be dangerous to the ecosystem of the Antarctic Region. On the other hand, high concentration of Be-7 has been detected in seaweed and lichens. Other natural radionuclide detected were Ra-226, Bi-214 and K-40.

Environmental radioactivity at Machu Picchu Scientific Station

International Nuclear Information System (INIS)

Gonzales, S.; Osores, J.; Jara, R.

1998-01-01

Studies on environmental radioactivity at the Peruvian Scientific Station were carried out in the last two austral summer periods. The main objective of this study is to establish an environmental radiological monitoring program for evaluating environmental components and achieving a baseline study related to artificial and natural radioactivity levels. For this purpose, samples such as seaweeds, mosses, lichens, soil seawater, ice, marine sediment and underground water were collected from the area surrounding the station starting from Punta Crepin to Playa Inca and Playa Naylamp; then they were pre-conditioned in Machu Picchu Station and were sent to the Environmental Radioactivity laboratory of 'Racso' Peruvian Nuclear Center to conduct beta and gamma spectrometry. The Obtained results showed the presence of Cs-137 in geological components (soil and sediment) and in biological components (lichens and mosses). Nevertheless, those levels seem to be in a range of normal fluctuations after atmospheric nuclear testing and they are not considered to be dangerous to the ecosystem of the Antarctic Region. On the other hand, high concentration of Be-7 has been detected in seaweed and lichens. Other natural radionuclide detected were Ra-226, Bi-214 and K-40

Biological impact assessment of thermal discharges in the vicinity of Madras Atomic Power Station, Kalpakkam, India

International Nuclear Information System (INIS)

Shahul Hameed, P.; Syed Mohamed, H.E.; Krishnamoorthy, R.

2007-01-01

Madras Atomic Power Station (MAPS), Kalpakkam uses seawater as tertiary coolant at the rate of 35m 3 /sec employing a once through type of circuit. The discharged water travels as a canal and mixes with seawater at the mixing zone. The present study investigated the impact of the discharged thermal effluent on the physical chemical and biological quality of the receiving seawater body. The thermal plume is shore attached and extended up to 300 m from the shore and registered a ΔT of 3-4 degC. The shore attached thermal plume adversely affected the density and distribution of macro benthic animals. The benthos are absent in the mixing zone and their density decreased about 500 m on either side of the mixing zone. The natural shift in the mixing zone provides opportunities for the recolonization of macro benthos. The thermal tolerance study revealed that the experimental fish species Mugil cephalus and Alepeus djidapa did not show any mortality or loss of equilibrium at ΔT 5 degC (33 degC) and ΔT 7 degC (35 degC) and the maximum ΔT recorded at the impact area is 6 degC. The gradual increase in temperature as found in the plume favors the fishes to escape the acute thermal exposures. (author)

Neurobehavioral effects among inhabitants around mobile phone base stations.

Science.gov (United States)

Abdel-Rassoul, G; El-Fateh, O Abou; Salem, M Abou; Michael, A; Farahat, F; El-Batanouny, M; Salem, E

2007-03-01

exposure to RER from mobile phone base station antennas and using of NBTB for regular assessment and early detection of biological effects among inhabitants around the stations are recommended.

The Current Status of the Space Station Biological Research Project: a Core Facility Enabling Multi-Generational Studies under Slectable Gravity Levels

Science.gov (United States)

Santos, O.

2002-01-01

The Space Station Biological Research Project (SSBRP) has developed a new plan which greatly reduces the development costs required to complete the facility. This new plan retains core capabilities while allowing for future growth. The most important piece of equipment required for quality biological research, the 2.5 meter diameter centrifuge capable of accommodating research specimen habitats at simulated gravity levels ranging from microgravity to 2.0 g, is being developed by NASDA, the Japanese space agency, for the SSBRP. This is scheduled for flight to the ISS in 2007. The project is also developing a multi-purpose incubator, an automated cell culture unit, and two microgravity habitat holding racks, currently scheduled for launch in 2005. In addition the Canadian Space Agency is developing for the project an insect habitat, which houses Drosophila melanogaster, and provides an internal centrifuge for 1 g controls. NASDA is also developing for the project a glovebox for the contained manipulation and analysis of biological specimens, scheduled for launch in 2006. This core facility will allow for experimentation on small plants (Arabidopsis species), nematode worms (C. elegans), fruit flies (Drosophila melanogaster), and a variety of microorganisms, bacteria, yeast, and mammalian cells. We propose a plan for early utilization which focuses on surveys of changes in gene expression and protein structure due to the space flight environment. In the future, the project is looking to continue development of a rodent habitat and a plant habitat that can be accommodated on the 2.5 meter centrifuge. By utilizing the early phases of the ISS to broadly answer what changes occur at the genetic and protein level of cells and organisms exposed to the ISS low earth orbit environment, we can generate interest for future experiments when the ISS capabilities allow for direct manipulation and intervention of experiments. The ISS continues to hold promise for high quality, long

Simulation of Martian EVA at the Mars Society Arctic Research Station

Science.gov (United States)

Pletser, V.; Zubrin, R.; Quinn, K.

The Mars Society has established a Mars Arctic Research Station (M.A.R.S.) on Devon Island, North of Canada, in the middle of the Haughton crater formed by the impact of a large meteorite several million years ago. The site was selected for its similarities with the surface of the Mars planet. During the Summer 2001, the MARS Flashline Research Station supported an extended international simulation campaign of human Mars exploration operations. Six rotations of six person crews spent up to ten days each at the MARS Flashline Research Station. International crews, of mixed gender and professional qualifications, conducted various tasks as a Martian crew would do and performed scientific experiments in several fields (Geophysics, Biology, Psychology). One of the goals of this simulation campaign was to assess the operational and technical feasibility of sustaining a crew in an autonomous habitat, conducting a field scientific research program. Operations were conducted as they would be during a Martian mission, including Extra-Vehicular Activities (EVA) with specially designed unpressurized suits. The second rotation crew conducted seven simulated EVAs for a total of 17 hours, including motorized EVAs with All Terrain Vehicles, to perform field scientific experiments in Biology and Geophysics. Some EVAs were highly successful. For some others, several problems were encountered related to hardware technical failures and to bad weather conditions. The paper will present the experiment programme conducted at the Mars Flashline Research Station, the problems encountered and the lessons learned from an EVA operational point of view. Suggestions to improve foreseen Martian EVA operations will be discussed.

The International Space Station: A Pathway to the Future

Science.gov (United States)

Kitmacher, Gary H.; Gerstenmaier, William H.; Bartoe, John-David F.; Mustachio, Nicholas

2004-01-01

Nearly six years after the launch of the first International Space Station element, and four years after its initial occupation, the United States and our 16 international partners have made great strides in operating this impressive Earth orbiting research facility. This past year we have done so in the face of the adversity of operating without the benefit of the Space Shuttle. In his January 14, 2004, speech announcing a new vision for America's space program, President Bush affirmed the United States' commitment to completing construction of the International Space Station by 2010. The President also stated that we would focus our future research aboard the Station on the longterm effects of space travel on human biology. This research will help enable human crews to venture through the vast voids of space for months at a time. In addition, ISS affords a unique opportunity to serve as an engineering test bed for hardware and operations critical to the exploration tasks. NASA looks forward to working with our partners on International Space Station research that will help open up new pathways for future exploration and discovery beyond low Earth orbit. This paper provides an overview of the International Space Station Program focusing on a review of the events of the past year, as well as plans for next year and the future.

Biological monitoring of radiation exposure

Science.gov (United States)

Horneck, G.

1998-11-01

Complementary to physical dosimetry, biological dosimetry systems have been developed and applied which weight the different components of environmental radiation according to their biological efficacy. They generally give a record of the accumulated exposure of individuals with high sensitivity and specificity for the toxic agent under consideration. Basically three different types of biological detecting/monitoring systems are available: (i) intrinsic biological dosimeters that record the individual radiation exposure (humans, plants, animals) in measurable units. For monitoring ionizing radiation exposure, in situ biomarkers for genetic (e.g. chromosomal aberrations in human lymphocytes, germ line minisatellite mutation rates) or metabolic changes in serum, plasma and blood (e.g. serum lipids, lipoproteins, lipid peroxides, melatonin, antibody titer) have been used. (ii) Extrinsic biological dosimeters/indicators that record the accumulated dose in biological model systems. Their application includes long-term monitoring of changes in environmental UV radiation and its biological implications as well as dosimetry of personal UV exposure. (iii) Biological detectors/biosensors for genotoxic substances and agents such as bacterial assays (e.g. Ames test, SOS-type test) that are highly sensitive to genotoxins with high specificity. They may be applicable for different aspects in environmental monitoring including the International Space Station.

Innovative Railway Stations

Science.gov (United States)

Rzepnicka, Sylwia; Załuski, Daniel

2017-10-01

In relation to modern demographic trends, evolving technologies and environment-friendly solutions increases the potential of rail considered as sustainable form of public transport. Contemporary tendencies of designing railway stations in Europe are focused on lowering energy consumption and reducing carbon emission. The main goal of the designers is to create a friendly and intuitive space for its users and at the same time a building that uses renewable energy sources and minimizes negative impact on the environment by the increase of biologically active areas, reuse of rainwater and greywater, innovative heating and cooling solutions and reduction of energy losses. The optimisation of a life circle in railway architecture introduces new approach to passenger service. Examples mentioned in the content of this article help to synthesize changes in approach to the design within the context of sustainability.

IMOS National Reference Stations: A Continental-Wide Physical, Chemical and Biological Coastal Observing System

Science.gov (United States)

Lynch, Tim P.; Morello, Elisabetta B.; Evans, Karen; Richardson, Anthony J.; Rochester, Wayne; Steinberg, Craig R.; Roughan, Moninya; Thompson, Peter; Middleton, John F.; Feng, Ming; Sherrington, Robert; Brando, Vittorio; Tilbrook, Bronte; Ridgway, Ken; Allen, Simon; Doherty, Peter; Hill, Katherine; Moltmann, Tim C.

2014-01-01

Sustained observations allow for the tracking of change in oceanography and ecosystems, however, these are rare, particularly for the Southern Hemisphere. To address this in part, the Australian Integrated Marine Observing System (IMOS) implemented a network of nine National Reference Stations (NRS). The network builds on one long-term location, where monthly water sampling has been sustained since the 1940s and two others that commenced in the 1950s. In-situ continuously moored sensors and an enhanced monthly water sampling regime now collect more than 50 data streams. Building on sampling for temperature, salinity and nutrients, the network now observes dissolved oxygen, carbon, turbidity, currents, chlorophyll a and both phytoplankton and zooplankton. Additional parameters for studies of ocean acidification and bio-optics are collected at a sub-set of sites and all data is made freely and publically available. Our preliminary results demonstrate increased utility to observe extreme events, such as marine heat waves and coastal flooding; rare events, such as plankton blooms; and have, for the first time, allowed for consistent continental scale sampling and analysis of coastal zooplankton and phytoplankton communities. Independent water sampling allows for cross validation of the deployed sensors for quality control of data that now continuously tracks daily, seasonal and annual variation. The NRS will provide multi-decadal time series, against which more spatially replicated short-term studies can be referenced, models and remote sensing products validated, and improvements made to our understanding of how large-scale, long-term change and variability in the global ocean are affecting Australia's coastal seas and ecosystems. The NRS network provides an example of how a continental scaled observing systems can be developed to collect observations that integrate across physics, chemistry and biology. PMID:25517905

IMOS National Reference Stations: a continental-wide physical, chemical and biological coastal observing system.

Directory of Open Access Journals (Sweden)

Tim P Lynch

Full Text Available Sustained observations allow for the tracking of change in oceanography and ecosystems, however, these are rare, particularly for the Southern Hemisphere. To address this in part, the Australian Integrated Marine Observing System (IMOS implemented a network of nine National Reference Stations (NRS. The network builds on one long-term location, where monthly water sampling has been sustained since the 1940s and two others that commenced in the 1950s. In-situ continuously moored sensors and an enhanced monthly water sampling regime now collect more than 50 data streams. Building on sampling for temperature, salinity and nutrients, the network now observes dissolved oxygen, carbon, turbidity, currents, chlorophyll a and both phytoplankton and zooplankton. Additional parameters for studies of ocean acidification and bio-optics are collected at a sub-set of sites and all data is made freely and publically available. Our preliminary results demonstrate increased utility to observe extreme events, such as marine heat waves and coastal flooding; rare events, such as plankton blooms; and have, for the first time, allowed for consistent continental scale sampling and analysis of coastal zooplankton and phytoplankton communities. Independent water sampling allows for cross validation of the deployed sensors for quality control of data that now continuously tracks daily, seasonal and annual variation. The NRS will provide multi-decadal time series, against which more spatially replicated short-term studies can be referenced, models and remote sensing products validated, and improvements made to our understanding of how large-scale, long-term change and variability in the global ocean are affecting Australia's coastal seas and ecosystems. The NRS network provides an example of how a continental scaled observing systems can be developed to collect observations that integrate across physics, chemistry and biology.

Life Sciences Space Station planning document: A reference payload for the Life Sciences Research Facility

Science.gov (United States)

1986-01-01

The Space Station, projected for construction in the early 1990s, will be an orbiting, low-gravity, permanently manned facility providing unprecedented opportunities for scientific research. Facilities for Life Sciences research will include a pressurized research laboratory, attached payloads, and platforms which will allow investigators to perform experiments in the crucial areas of Space Medicine, Space Biology, Exobiology, Biospherics and Controlled Ecological Life Support System (CELSS). These studies are designed to determine the consequences of long-term exposure to space conditions, with particular emphasis on assuring the permanent presence of humans in space. The applied and basic research to be performed, using humans, animals, and plants, will increase our understanding of the effects of the space environment on basic life processes. Facilities being planned for remote observations from platforms and attached payloads of biologically important elements and compounds in space and on other planets (Exobiology) will permit exploration of the relationship between the evolution of life and the universe. Space-based, global scale observations of terrestrial biology (Biospherics) will provide data critical for understanding and ultimately managing changes in the Earth's ecosystem. The life sciences community is encouraged to participate in the research potential the Space Station facilities will make possible. This document provides the range and scope of typical life sciences experiments which could be performed within a pressurized laboratory module on Space Station.

Fire safety in nuclear power stations

International Nuclear Information System (INIS)

Kench, R.L.

1988-01-01

This is the first of a three-part report on the fire hazards in nuclear power stations and some of the precautions necessary. This part lists the United Kingdom reactors, outlines how they work, the fuels used, the use of moderators and coolants and the control systems. Although the risk of fire is no higher than in fossil-fuel stations the consequences can be more serious. The radioactive materials used mean that there is biological shielding round the core, limitations on waste emissions allowed and limited access to some zones. Reliable shut-down systems are needed. Care in the use of water to fight fires must be exercised -it can act as a moderator and cause an otherwise safe core to go critical. The Wigner effect in graphite moderated reactors is explained. Fires in graphite can be extinguished by carbon dioxide. Argon, chlorine and sodium silicate can also be effective. In sodium cooled reactors fires can be allowed to burn themselves out, or TEC and argon could be used to extinguish the flame. (UK)

Biological flue gas desulfurization

Energy Technology Data Exchange (ETDEWEB)

Buisman, C.J.N.; Dijkman, H.; Wijte, G.; Prins, W.L.; Verbraak, P.; Hartog, H.A.J. den [Paper B.V. Blak (Netherlands)

1995-08-01

A new biological flue gas desulfurization process (BIO-FGD) producing sulphur as a by-product was invented by Paques BV and Hoogens Technical Services in 1993. Sulphur dioxide is absorbed from flue gas using a combination of a sodium based scrubber and two biological reactors, an anaerobic and an aerobic biological reactor. The article describes the process and its evaluation in a pilot plant at 2 MW scale, designed to remove 6 kg/hr SO{sub 2} of the 2 million m{sup 3}/hr of flue gas produced at the 600 MW coal fired power station Amer-8 situated in Geertruidenberg in the south of the Netherlands. Research so far has proved the process works successfully and at low cost. A second pilot plant due to start-up in May 1995 will provide data on scale up and further information on sulphur recovery. 5 refs., 5 figs.

National Aeronautics and Space Administration Biological Specimen Repository

Science.gov (United States)

McMonigal, Kathleen A.; Pietrzyk, Robert a.; Johnson, Mary Anne

2008-01-01

The National Aeronautics and Space Administration Biological Specimen Repository (Repository) is a storage bank that is used to maintain biological specimens over extended periods of time and under well-controlled conditions. Samples from the International Space Station (ISS), including blood and urine, will be collected, processed and archived during the preflight, inflight and postflight phases of ISS missions. This investigation has been developed to archive biosamples for use as a resource for future space flight related research. The International Space Station (ISS) provides a platform to investigate the effects of microgravity on human physiology prior to lunar and exploration class missions. The storage of crewmember samples from many different ISS flights in a single repository will be a valuable resource with which researchers can study space flight related changes and investigate physiological markers. The development of the National Aeronautics and Space Administration Biological Specimen Repository will allow for the collection, processing, storage, maintenance, and ethical distribution of biosamples to meet goals of scientific and programmatic relevance to the space program. Archiving of the biosamples will provide future research opportunities including investigating patterns of physiological changes, analysis of components unknown at this time or analyses performed by new methodologies.

Space Station Centrifuge: A Requirement for Life Science Research

Science.gov (United States)

Smith, Arthur H.; Fuller, Charles A.; Johnson, Catherine C.; Winget, Charles M.

1992-01-01

A centrifuge with the largest diameter that can be accommodated on Space Station Freedom is required to conduct life science research in the microgravity environment of space. (This was one of the findings of a group of life scientists convened at the University of California, Davis, by Ames Research Center.) The centrifuge will be used as a research tool to understand how gravity affects biological processes; to provide an on-orbit one-g control; and to assess the efficacy of using artificial gravity to counteract the deleterious biological effect of space flight. The rationale for the recommendation and examples of using ground-based centrifugation for animal and plant acceleration studies are presented. Included are four appendixes and an extensive bibliography of hypergravity studies.

Promoting the use of measurement tools in practice: a mixed-methods study of the activities and experiences of physical therapist knowledge brokers.

Science.gov (United States)

Rivard, Lisa M; Russell, Dianne J; Roxborough, Lori; Ketelaar, Marjolijn; Bartlett, Doreen J; Rosenbaum, Peter

2010-11-01

The use of knowledge brokers (KBs) has been recommended as a mechanism to facilitate the use of research evidence in clinical practice. However, little has been written regarding the practical implementation of the KB role. This article (1) describes the brokering activities of 24 pediatric physical therapist KBs (in Ontario, Alberta, and British Columbia, Canada), and (2) reports KBs' perceptions of the utility of their role and their experiences with the brokering process. A mixed-methods research design was used in this investigation, which was part of a larger knowledge translation (KT) study that demonstrated the effectiveness of using KBs to implement a group of evidence-based measurement tools into practice. The KBs completed weekly activity logs, which were summarized and described. Semi-structured telephone interviews with KBs were analyzed qualitatively to provide insight into their perceptions of their role and the brokering process. Major interview themes were identified and verified through member checking. Brokering activities varied considerably as KBs adapted to meet the needs of their colleagues. The KBs indicated that they highly valued the connection to the research community and spoke of the enthusiastic engagement of their physical therapist colleagues (and others in their organization) in the brokering process. They discussed the importance of understanding the practice context and organizational factors that could affect knowledge transfer. The KBs spoke of the need to dedicate time for the role and had a strong sense of the supports needed to implement a KB role in future. Considerable variation in brokering activities was demonstrated across KB participants. The KBs perceived their role as useful and indicated that organizational commitment is crucial to the success of this KT strategy.

Non-Coop Station History

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Station history documentation for stations outside the US Cooperative Observer network. Primarily National Weather Service stations assigned WBAN station IDs. Other...

Medical Applications of Space Light-Emitting Diode Technology--Space Station and Beyond

Energy Technology Data Exchange (ETDEWEB)

Whelan, H.T.; Houle, J.M.; Donohoe, D.L.; Bajic, D.M.; Schmidt, M.H.; Reichert, K.W.; Weyenberg, G.T.; Larson, D.L.; Meyer, G.A.; Caviness, J.A.

1999-06-01

Space light-emitting diode (LED) technology has provided medicine with a new tool capable of delivering light deep into tissues of the body, at wavelengths which are biologically optimal for cancer treatment and wound healing. This LED technology has already flown on Space Shuttle missions, and shows promise for wound healing applications of benefit to Space Station astronauts.

Physics Research on the International Space Station

CERN Multimedia

CERN. Geneva

2012-01-01

The International Space Station (ISS) is orbiting Earth at an altitude of around 400 km. It has been manned since November 2000 and currently has a permanent crew of six. On-board ISS science is done in a wide field of sciences, from fundamental physics to biology and human physiology. Many of the experiments utilize the unique conditions of weightlessness, but also the views of space and the Earth are exploited. ESA’s (European Space Agency) ELIPS (European Programme Life and Physical sciences in Space) manages some 150 on-going and planned experiments for ISS, which is expected to be utilized at least to 2020. This presentation will give a short introduction to ISS, followed by an overview of the science field within ELIPS and some resent results. The emphasis, however, will be on ISS experiments which are close to the research performed at CERN. Silicon strip detectors like ALTEA are measuring the flux of ions inside the station. ACES (Atomic Clock Ensemble in Space) will provide unprecedented global ti...

47 CFR 80.107 - Service of private coast stations and marine-utility stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Service of private coast stations and marine...) SAFETY AND SPECIAL RADIO SERVICES STATIONS IN THE MARITIME SERVICES Operating Requirements and Procedures Operating Procedures-Land Stations § 80.107 Service of private coast stations and marine-utility stations. A...

MIT-NASA/KSC space life science experiments - A telescience testbed

Science.gov (United States)

Oman, Charles M.; Lichtenberg, Byron K.; Fiser, Richard L.; Vordermark, Deborah S.

1990-01-01

Experiments performed at MIT to better define Space Station information system telescience requirements for effective remote coaching of astronauts by principal investigators (PI) on the ground are described. The experiments were conducted via satellite video, data, and voice links to surrogate crewmembers working in a laboratory at NASA's Kennedy Space Center. Teams of two PIs and two crewmembers performed two different space life sciences experiments. During 19 three-hour interactive sessions, a variety of test conditions were explored. Since bit rate limits are necessarily imposed on Space Station video experiments surveillance video was varied down to 50 Kb/s and the effectiveness of PI controlled frame rate, resolution, grey scale, and color decimation was investigated. It is concluded that remote coaching by voice works and that dedicated crew-PI voice loops would be of great value on the Space Station.

Particulate Trace Element Cycling in a Diatom Bloom at Station ALOHA

Science.gov (United States)

Weisend, R.; Morton, P. L.; Landing, W. M.; Fitzsimmons, J. N.; Hayes, C. T.; Boyle, E. A.

2014-12-01

Phytoplankton in oligotrophic marine deserts depend on remote sources to supply trace nutrients. To examine these sources, marine particulate matter samples from the central North Pacific (Station ALOHA) were collected during the July-August 2012 HOE-DYLAN cruises and analyzed for a suite of trace (e.g., Fe, Mn) and major (e.g. Al, P) elements. Daily surface SPM samples were examined for evidence of atmospheric deposition and biological uptake, while five vertical profiles were examined for evidence of surface vertical export and subsurface horizontal transport from nearby sources (e.g., margin sediments, hydrothermal plumes). Maxima in surface particulate P (a biological tracer) corresponded with a diatom bloom, and surprisingly also coincided with maxima in particulate Al (typically a tracer for lithogenic inputs). The surface particulate Al distributions likely result from the adsorption of dissolved Al onto diatom silica frustules, not from atmospheric dust deposition. In addition, a subsurface maximum in particulate Al and P was observed four days later at 75m, possibly resulting from vertical export of the surface diatom bloom. The distributions of other bioactive trace elements (e.g. Cd, Co, Cu) will be presented in the context of the diatom bloom and other biological, chemical and physical features. A second, complementary poster is also being presented which examines the cycling of trace elements in lithogenic particles (Morton et al., "Trace Element Cycling in Lithogenic Particles at Station ALOHA").

47 CFR 73.6016 - Digital Class A TV station protection of TV broadcast stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Digital Class A TV station protection of TV... Class A TV station protection of TV broadcast stations. Digital Class A TV stations must protect authorized TV broadcast stations, applications for minor changes in authorized TV broadcast stations filed on...

Fire Stations

Data.gov (United States)

Department of Homeland Security — Fire Stations in the United States Any location where fire fighters are stationed or based out of, or where equipment that such personnel use in carrying out their...

Do cities deserve more railway stations? The choice of a departure railway station in a multiple-station region

NARCIS (Netherlands)

Givoni, M.; Rietveld, P.

2014-01-01

Promoting the use of rail is an important element in sustainable transport policy. One of the most important decisions to make in planning the railway network is on the number of stations to provide. Stations are the access points to rail services and while each additional station increases rail's

47 CFR 73.6018 - Digital Class A TV station protection of DTV stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Digital Class A TV station protection of DTV... TV station protection of DTV stations. Digital Class A TV stations must protect the DTV service that... application for digital operation of an existing Class A TV station or to change the facilities of a digital...

Documentation of meteorological data from the coniferous forest biome primary station in Oregon.

Science.gov (United States)

R.H. Waring; H.R. Holbo; R.P. Bueb; R.L. Fredriksen

1978-01-01

As part of the International Biological Program, a primary meteorological station was installed in the west-central Cascade Range of Oregon. Short-wave solar radiation, air temperature, dewpoint temperature, windspeed, and precipitation are recorded continuously. Climatic data are summarized in a daily record available from May 11, 1972, to date. This report details...

FODA/IBEA-TDMA - A flexible fade countermeasure system for integrated services in user-oriented networks

Science.gov (United States)

Celandroni, N.; Ferro, E.; James, N.; Potorti, F.

1992-12-01

A flexible, processor based, TDMA station has been implemented. This station and its associated variable data rate modem enables users to implement very complex frame structures under software control. Burst rates of 512 kb/s-8x192 Mb/s and different coding rates are possible allowing the transmitted bit energy from each station in the network to be adapted to prevailing conditions. The proposed application of the station is the transmission of mixed stream and packet traffic, in a LANs interconnection via satellite environment, using a modification of the FODA technique. The association of the up-link power control feature with the bit and coding rate variation gives the system an interesting ability to cope with fade conditions. The link outage probability is investigated for the Olympus transponder in Ka band. The ability of the system, together with the good performance of Olympus, shows that the Ka band is usable for the above mentioned types of networks without prohibitive fade degradation, at least for limited coverages.

Comparison of three commercial knowledge bases for detection of drug-drug interactions in clinical decision support.

Science.gov (United States)

Fung, Kin Wah; Kapusnik-Uner, Joan; Cunningham, Jean; Higby-Baker, Stefanie; Bodenreider, Olivier

2017-07-01

To compare 3 commercial knowledge bases (KBs) used for detection and avoidance of potential drug-drug interactions (DDIs) in clinical practice. Drugs in the DDI tables from First DataBank (FDB), Micromedex, and Multum were mapped to RxNorm. The KBs were compared at the clinical drug, ingredient, and DDI rule levels. The KBs were evaluated against a reference list of highly significant DDIs from the Office of the National Coordinator for Health Information Technology (ONC). The KBs and the ONC list were applied to a prescription data set to simulate their use in clinical decision support. The KBs contained 1.6 million (FDB), 4.5 million (Micromedex), and 4.8 million (Multum) clinical drug pairs. Altogether, there were 8.6 million unique pairs, of which 79% were found only in 1 KB and 5% in all 3 KBs. However, there was generally more agreement than disagreement in the severity rankings, especially in the contraindicated category. The KBs covered 99.8-99.9% of the alerts of the ONC list and would have generated 25 (FDB), 145 (Micromedex), and 84 (Multum) alerts per 1000 prescriptions. The commercial KBs differ considerably in size and quantity of alerts generated. There is less variability in severity ranking of DDIs than suggested by previous studies. All KBs provide very good coverage of the ONC list. More work is needed to standardize the editorial policies and evidence for inclusion of DDIs to reduce variation among knowledge sources and improve relevance. Some DDIs considered contraindicated in all 3 KBs might be possible candidates to add to the ONC list. Published by Oxford University Press on behalf of the American Medical Informatics Association 2017. This work is written by US Government employees and is in the public domain in the United States.

Project JADE. Long-term function and safety. Comparison of repository systems

International Nuclear Information System (INIS)

Birgersson, Lars; Pers, K.; Wiborgh, M.

2001-12-01

A comparison of the KBS-3 V(ertical deposition), KBS-3 H(orizontal deposition) and MLH repository systems with regard to the long-term repository performance and the radionuclide migration is presented in the report. Several differences between the repository systems have been identified. The differences are mainly related to the: distance between canister and backfilled tunnels, excavated rock volumes, deposition hole direction. The overall conclusion is that the differences are in general quite small with regard to the repository function and safety. None of the differences are of such importance for the long-term repository performance and radionuclide migration that they discriminate any of the repository systems. The differences between the two KBS-3 systems are small. Based on this study, there is no reason to change from the reference system KBS-3 V to KBS-3 H. MLH has the potential to be a very robust system, especially in a long-term perspective. However, the MLH system will require extensive research, development, and analysis before it will be as confident as the reference repository system, KBS-3 V. Although the MLH and KBS-3 H systems are in some ways favourable compared to the reference system KBS-3 V, the overall conclusion is that the KBS-3 V system is still a very attractive system. A major advantage with KBS-3 V is that it is by far the most investigated and developed system. The JADE-project was initiated in 1996, and the main part of the study was carried out during 1997 and 1998. The JADE study is consequently based on presumptions that were valid a few years ago. Some of these presumptions have been modified since then. The new presumptions are however not judged to change the overall conclusions

Sizewell 'B' power station public inquiry: CEGB proof of evidence

International Nuclear Information System (INIS)

Hawes, F.B.

1982-11-01

The biological consequences of using a direct cooled system at the proposed Sizewell B power station are dealt with. Problems caused by the impingement of organisms on the fine-mesh screens through which the water is pumped, by the entrainment of smaller organisms in the flow through the cooling system and by the discharge of warmed chlorinated water into the sea are discussed. The chlorination of cooling water is described. (U.K.)

From city’s station to station city. An integrative spatial approach to the (redevelopment of station areas

Directory of Open Access Journals (Sweden)

Ana Luísa Martins da Conceição

2014-12-01

Full Text Available Since its origin, the railway station has had a complicated relationship with the city, demanding periodical updates, particularly regarding spatial issues. With the aim of improving the liveability of station areas, current redevelopment projects are reconceptualising them as balanced transport ‘nodes’ and ‘places’ in the city. However, the proposed spatial solutions do not fully support the sought after economic, social and environmental performances. These intentions continue to be predominantly bounded with the (abstract planological level, not finding appropriate translation at the (concrete spatial design level. Further, the interdisciplinary nature of the highly complex planning and design processes of station areas, which should contribute to enhance the performance of their spaces, reinforces constraints and relegates architecture to a marginal role in this quest. It is thus necessary to understand how architecture can contribute to the improvement of the spatial performance of contemporary stations areas, supporting their current reconceptualization. To gain this understanding, the research explored the factors which influence the spatial definition and performance of European High Speed Train station areas, using “design research” and “research by design”. Via a theoretical integrative framework, synthesized from knowledge developed by architecture and other sciences, case studies of ‘through’ stations were analysed and compared. Six cases, encapsulating the most recurrent relative positions of the railway (infrastructure and the station building towards the(ir direct built environment, were chosen out of a large sample. For each category (cases with railway tracks at (a ground level, (b elevated level and (c underground level, two cases, featuring an adapted station building and a newly built one, were studied. Their physical and functional characteristics were mapped at several scales and moments (in history, as

Clientelism and vote buying in local elections: A case study of Kartu Bintan Sejahtera

Directory of Open Access Journals (Sweden)

Tri Samnuzulsari

2018-03-01

Full Text Available This study finds out clientelism and vote buying on Kartu Bintan Sejahtera (KBS in Bintan Regency, Riau Islands. The objective of this study is to understand the practices of clientelism and vote buying using KBS. This study based on case study research. The informants consist of General Election Commission of (KPUD Riau Islands, candidates of the governor of Riau Islands 2015-2020, candidates of Bintan Regent 2015-2020, along with their supporting parties and campaigning team, and bureaucracy of the implementation of KBS. The main findings of this study suggest that KBS is used as a clientelism and vote buying practices by the candidate of Riau Islands governor and Bintan Regent, 2015-2020 period. This study also finds that formal and informal political networks are utilized by the candidates as a clientelism and vote buying arenas. This study not only contributes to the literature of clientelism and vote buying, but also adds the literature of social policy in the context of Indonesian local politics setting. This study suggests that KBS is used as a media to obtain the support of the voters in the election of governor of Riau Islands and regent of Bintan 2015-2020. All candidates capitalize the issue of KBS to obtain the popularity. The patterns of the practice of clientelism and vote buying in KBS is by using various media campaigns to promote the success story of KBS. Not only in formal campaign but also in informal campaign, they always promote KBS as their success.

User-Friendly End Station at the ALS for Nanostructure Characterization

International Nuclear Information System (INIS)

F. J. Himpsel; P. Alivisatos; T. Callcott; J. Carlisle; J. D. Denlinger; D. E. Eastman; D. Ederer; Z. Hussain; L.J. Terminello; T. Van Buuren; R. S. Williams

2006-01-01

This is a construction project for an end station at the ALS, which is optimized for measuring NEXAFS of nanostructures with fluorescence detection. Compared to the usual electron yield detection, fluorescence is able to probe buried structures and is sensitive to dilute species, such as nanostructures supported on a substrate. Since the quantum yield for fluorescence is 10 -4 -10 -5 times smaller than for electrons in the soft x-ray regime, such an end station requires bright undulator beamlines at the ALS. In order to optimize the setup for a wide range of applications, two end stations were built: (1) A simple, mobile chamber with efficient photon detection (>10 4 times the solid angle collection of fluorescence spectrographs) and a built-in magnet for MCD measurements at EPU beamlines (Fig. 1 left). It allows rapid mapping the electronic states of nanostructures (nanocrystals, nanowires, tailored magnetic materials, buried interfaces, biologically-functionalized surfaces). It was used with BL 8.0 (linear polarized undulator) and BL 4.0 (variable polarization). (2) A sophisticated, stationary end station operating at Beamline 8.0 (Fig. 1 right). It contains an array of surface characterization instruments and a micro-focus capability for scanning across graded samples (wedges for thickness variation, stoichiometry gradients, and general variations of the sample preparation conditions for optimizing nanostructures)

Science review of the Beaufort Institute of Oceanography, the Halifax Fisheries Research Laboratory, and the St. Andrews Biological Station, 1990-91. Revue des sciences de l'Institut oceanographique de Bedford, du Laboratoire de recherche halieutique de Halifax, et de la Station biologique de St. Andrews, 1990-91

Energy Technology Data Exchange (ETDEWEB)

Smith, T E; Cook, J [eds.

1992-01-01

A review is presented of the research and survey programs being undertaken in 1990-91 at the Bedford Institute of Oceanography, the Halifax Fisheries Research Laboratory, and the St. Andrews Biological Station (all in Nova Scotia). The broad objectives of these programs are to perform applied research leading to the provision of advice on the management of marine and freshwater environments, including fisheries and offshore hydrocarbon resources; to perform targeted basic research in accordance with the mandates of Canada's Department of Fisheries and Oceans, Environment Canada, and Energy, Mines and Resources; to perform surveys and cartographic work; and to respond to major marine environmental emergencies. The research and survey work encompasses the fields of marine geology and geophysics, physical oceanography, marine chemistry, biological oceanography, fisheries research, seabird research, and navigational surveys and cartography. Topics of specific projects reviewed include marine pollution detection, phytoplankton profiling, seal populations, ocean mapping, geographic information systems, fish and invertebrate nutrition, shellfish culture, lobster habitat ecology, physics and biology of the Georges Bank frontal system, water-level instrumentation, data acquisition techniques, sea ice monitoring, salmon management, nearshore sedimentary processes, and oil/gas distribution in offshore basins. Separate abstracts have been prepared for three project reports from this review.

Kluver–Bucy syndrome in one case with systemic lupus erythematosus

Directory of Open Access Journals (Sweden)

Hsiu-Fen Lin

2011-04-01

Full Text Available Kluver–Bucy syndrome (KBS is a collection of neuropsychiatric symptoms, including visual agnosia (prosopagnosia, hypermetamorphosis, placidity, hypersexuality, and hyperorality. Although neuropsychiatric manifestation is prevalent in cases with systemic lupus erythematosus (SLE, only one literature reported a case with SLE that had KBS previously. In this article, a 37-year-old woman with SLE who developed KBS and other neuropsychiatric symptoms is presented. Brain imaging proved the relevant structural lesion. The possible explanation of pathogenesis of KBS in SLE is discussed.

Estimating Pedestrian flows at train stations using the Station Transfer Model

NARCIS (Netherlands)

Van den Heuvel, J.P.A.; Dekkers, K.; De Vos, S.

2012-01-01

Train stations play a vital role in the door to door travel experience of train passengers. From the passengers’ value of time perspective, the station is the weakest link in total time value of the journey. Within the station the transfer function – moving between the various transport modes and

Broadcasting Stations of the World; Part III. Frequency Modulation Broadcasting Stations.

Science.gov (United States)

Foreign Broadcast Information Service, Washington, DC.

This third part of "Broadcasting Stations of the World", which lists all reported radio broadcasting and television stations, with the exception of those in the United States which broadcast on domestic channels, covers frequency modulation broadcasting stations. It contains two sections: one indexed alphabetically by country and city, and the…

Life Sciences Research in the Centrifuge Accommodation Module of the International Space Station

Science.gov (United States)

Dalton, Bonnie P.; Plaut, Karen; Meeker, Gabrielle B.; Sun, Sid (Technical Monitor)

2000-01-01

The Centrifuge Accommodation Module (CAM) will be the home of the fundamental biology research facilities on the International Space Station (ISS). These facilities are being built by the Biological Research Project (BRP), whose goal is to oversee development of a wide variety of habitats and host systems to support life sciences research on the ISS. The habitats and host systems are designed to provide life support for a variety of specimens including cells, bacteria, yeast, plants, fish, rodents, eggs (e.g., quail), and insects. Each habitat contains specimen chambers that allow for easy manipulation of specimens and alteration of sample numbers. All habitats are capable of sustaining life support for 90 days and have automated as well as full telescience capabilities for sending habitat parameters data to investigator homesite laboratories. The habitats provide all basic life support capabilities including temperature control, humidity monitoring and control, waste management, food, media and water delivery as well as adjustable lighting. All habitats will have either an internal centrifuge or are fitted to the 2.5-meter diameter centrifuge allowing for variable centrifugation up to 2 g. Specimen chambers are removable so that the specimens can be handled in the life sciences glovebox. Laboratory support equipment is provided for handling the specimens. This includes a compound and dissecting microscope with advanced video imaging, mass measuring devices, refrigerated centrifuge for processing biological samples, pH meter, fixation and complete cryogenic storage capabilities. The research capabilities provided by the fundamental biology facilities will allow for flexibility and efficiency for long term research on the International Space Station.

Guidelines for Learning Stations.

Science.gov (United States)

Fehrle, Carl C.; Schulz, Jolene

Guidelines for designing and planning learning stations for pupils at the elementary grade level include suggestions on how to develop a station that will be successful in meeting the learners' needs. Instructions for the use of tapes at a station and matching pupils with stations are given, as are guidelines on classroom arrangement and record…

The centrifuge facility - A life sciences research laboratory for Space Station Freedom

Science.gov (United States)

Fuller, Charles A.; Johnson, Catherine C.; Hargens, Alan R.

1991-01-01

The paper describes the centrifugal facility that is presently being developed by NASA for studies aboard the Space Station Freedom on the role of gravity, or its absence, at varying intensities for varying periods of time and with multiple model systems. Special attention is given to the design of the centrifuge system, the habitats designed to hold plants and animals, the glovebox system designed for experimental manipulations of the specimens, and the service unit. Studies planned for the facility will include experiments in the following disciplines: cell and developmental biology, plant biology, regulatory physiology, musculoskeletal physiology, behavior and performance, neurosciences, cardiopulmonary physiology, and environmental health and radiation.

Requirements for modeling airborne microbial contamination in space stations

Science.gov (United States)

Van Houdt, Rob; Kokkonen, Eero; Lehtimäki, Matti; Pasanen, Pertti; Leys, Natalie; Kulmala, Ilpo

2018-03-01

Exposure to bioaerosols is one of the facets that affect indoor air quality, especially for people living in densely populated or confined habitats, and is associated to a wide range of health effects. Good indoor air quality is thus vital and a prerequisite for fully confined environments such as space habitats. Bioaerosols and microbial contamination in these confined space stations can have significant health impacts, considering the unique prevailing conditions and constraints of such habitats. Therefore, biocontamination in space stations is strictly monitored and controlled to ensure crew and mission safety. However, efficient bioaerosol control measures rely on solid understanding and knowledge on how these bioaerosols are created and dispersed, and which factors affect the survivability of the associated microorganisms. Here we review the current knowledge gained from relevant studies in this wide and multidisciplinary area of bioaerosol dispersion modeling and biological indoor air quality control, specifically taking into account the specific space conditions.

Developmental state and perspectives of USSR power stations, espec. nuclear power stations

International Nuclear Information System (INIS)

1983-01-01

According to the resolutions of the 25th and 26th party congresses of the CPSU, the Soviet electric and thermal energy economy envisages as the mainstreams in development: Energy projects based on nuclear fuel, i.e. nuclear power stations (NPS), nuclear heat- and -power stations (NHPS) and nuclear heat stations (NHS); fuel-energy complexes: Ekibastuz, Kansk-Achinsk, West-Siberian complex (Tyumen); power stations utilizing non-conventional regenerative energy sources, i.e. solar, geothermal, MHD power stations. Further down, an overview is given on the developmental perspectives of nuclear-heat and nuclear-power economy and on the development of energy management based on fossil fuels. (orig./UA) [de

47 CFR 95.139 - Adding a small base station or a small control station.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Adding a small base station or a small control... base station or a small control station. (a) Except for a GMRS system licensed to a non-individual, one or more small base stations or a small control station may be added to a GMRS system at any point...

Illuminating Cell Biology

Science.gov (United States)

2002-01-01

NASA's Ames Research Center awarded Ciencia, Inc., a Small Business Innovation Research contract to develop the Cell Fluorescence Analysis System (CFAS) to address the size, mass, and power constraints of using fluorescence spectroscopy in the International Space Station's Life Science Research Facility. The system will play an important role in studying biological specimen's long-term adaptation to microgravity. Commercial applications for the technology include diverse markets such as food safety, in situ environmental monitoring, online process analysis, genomics and DNA chips, and non-invasive diagnostics. Ciencia has already sold the system to the private sector for biosensor applications.

Three-Dimensional Modelling of a KBS-3 Canister for Spent Nuclear Fuel - some migration studies - phase II

International Nuclear Information System (INIS)

Pereira, Antonio

2007-08-01

The resistance approach is nowadays very common in compartment modelling of radionuclide mass transport. In this work we examine with the help of a finite element code a particular application of the resistance approach method as used in modelling the near field of a KBS-3V repository. The motivation behind this work is that, although conceptually simple, the resistance approach to mass transfer, using many compartments linked together by resistances, rises two important issues related to the review process: transparency and quality assurance. Transforming the real geometry of the repository system in a number of 'equivalent compartments' makes for instance the input data used by the software difficult to grasp and the codes hard to read. With our three-dimensional finite element model we simulate the release of radionuclides from a copper canister perforated by a small pinhole through which the radionuclides escape from the canister gap and migrate in the bentonite by means of diffusion until they reach the fractured rock. Release rates are calculated for two radionuclides and the breakthrough curves are compared with SKB results. This direct approach to study the impact of the resistance methodology shows that the results obtained by the 3D-model are relatively close to the predictions of the compartment models of SKB. However, our model has a pinhole with constant cross section, introducing an important conceptual difference between the two models. In the SKB-model that cross section increases suddenly at 20 000 years. This implies that the boundary conditions of the two models are different, which impacts on the breakthrough curves of radionuclides which are not short-lived, even if we only model up to 20 000 years. Therefore the agreement between the two models is better for short-lived radionuclides. It is also shown in this report that the use of a commercial package of finite elements allows build a coupled flow-and mass transport model in 3D, using

The fault monitoring and diagnosis knowledge-based system for space power systems: AMPERES, phase 1

Science.gov (United States)

Lee, S. C.

1989-01-01

The objective is to develop a real time fault monitoring and diagnosis knowledge-based system (KBS) for space power systems which can save costly operational manpower and can achieve more reliable space power system operation. The proposed KBS was developed using the Autonomously Managed Power System (AMPS) test facility currently installed at NASA Marshall Space Flight Center (MSFC), but the basic approach taken for this project could be applicable for other space power systems. The proposed KBS is entitled Autonomously Managed Power-System Extendible Real-time Expert System (AMPERES). In Phase 1 the emphasis was put on the design of the overall KBS, the identification of the basic research required, the initial performance of the research, and the development of a prototype KBS. In Phase 2, emphasis is put on the completion of the research initiated in Phase 1, and the enhancement of the prototype KBS developed in Phase 1. This enhancement is intended to achieve a working real time KBS incorporated with the NASA space power system test facilities. Three major research areas were identified and progress was made in each area. These areas are real time data acquisition and its supporting data structure; sensor value validations; development of inference scheme for effective fault monitoring and diagnosis, and its supporting knowledge representation scheme.

Operational considerations for the Space Station Life Science Glovebox

Science.gov (United States)

Rasmussen, Daryl N.; Bosley, John J.; Vogelsong, Kristofer; Schnepp, Tery A.; Phillips, Robert W.

1988-01-01

The U.S. Laboratory (USL) module on Space Station will house a biological research facility for multidisciplinary research using living plant and animal specimens. Environmentally closed chambers isolate the specimen habitats, but specimens must be removed from these chambers during research procedures as well as while the chambers are being cleaned. An enclosed, sealed Life Science Glovebox (LSG) is the only locale in the USL where specimens can be accessed by crew members. This paper discusses the key science, engineering and operational considerations and constraints involving the LSG, such as bioisolation, accessibility, and functional versatility.

Developments of space station; Uchu station no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hashimoto, H. [National Space Development Agency of Japan, Tokyo (Japan)

1996-03-05

This paper introduces the Japanese experiment module (JEM) in developing a space station. The JEM consists of systems of a pressurizing section, an exposure section, a pressurizing portion of a supply section, a manipulator and an exposure portion of the supply section. The pressurizing section circulates and controls air so that crews can perform experiments under pressurized environment. The exposure section is a part in which experiments are carried out under exposure environment. The supply section runs between a station and the ground, with required devices loaded on it. The manipulator performs attaching a payload for the exposure section and replaces experimental samples. The JEM undergoes a schedule of fabricating an engineering model, testing for a certification a prototype flight model, and putting the model on a flight. The pressurizing section, exposure section and manipulator are at the stage of system tests. Surveillance of the JEM and control of the experiments are carried out at the Tsukuba Space Center. The Center is composed of a space experiment building, a zero-gravity environment testing building, an astronaut training building, a space station operating building, and a space station testing building. 7 figs., 2 tabs.

Space Station thermal storage/refrigeration system research and development

Science.gov (United States)

Dean, W. G.; Karu, Z. S.

1993-01-01

Space Station thermal loading conditions represent an order of magnitude increase over current and previous spacecraft such as Skylab, Apollo, Pegasus III, Lunar Rover Vehicle, and Lockheed TRIDENT missiles. Thermal storage units (TSU's) were successfully used on these as well as many applications for ground based solar energy storage applications. It is desirable to store thermal energy during peak loading conditions as an alternative to providing increased radiator surface area which adds to the weight of the system. Basically, TSU's store heat by melting a phase change material (PCM) such as a paraffin. The physical property data for the PCM's used in the design of these TSU's is well defined in the literature. Design techniques are generally well established for the TSU's. However, the Space Station provides a new challenge in the application of these data and techniques because of three factors: the large size of the TSU required, the integration of the TSU for the Space Station thermal management concept with its diverse opportunities for storage application, and the TSU's interface with a two-phase (liquid/vapor) thermal bus/central heat rejection system. The objective in the thermal storage research and development task was to design, fabricate, and test a demonstration unit. One test article was to be a passive thermal storage unit capable of storing frozen food at -20 F for a minimum of 90 days. A second unit was to be capable of storing frozen biological samples at -94 F, again for a minimum of 90 days. The articles developed were compatible with shuttle mission conditions, including safety and handling by astronauts. Further, storage rack concepts were presented so that these units can be integrated into Space Station logistics module storage racks. The extreme sensitivity of spacecraft radiator systems design-to-heat rejection temperature requirements is well known. A large radiator area penalty is incurred if low temperatures are accommodated via a

Newport Research Station

Data.gov (United States)

Federal Laboratory Consortium — The Newport Research Station is the Center's only ocean-port research facility. This station is located at Oregon State University's Hatfield Marine Science Center,...

Station Set Residual: Event Classification Using Historical Distribution of Observing Stations

Science.gov (United States)

Procopio, Mike; Lewis, Jennifer; Young, Chris

2010-05-01

Analysts working at the International Data Centre in support of treaty monitoring through the Comprehensive Nuclear-Test-Ban Treaty Organization spend a significant amount of time reviewing hypothesized seismic events produced by an automatic processing system. When reviewing these events to determine their legitimacy, analysts take a variety of approaches that rely heavily on training and past experience. One method used by analysts to gauge the validity of an event involves examining the set of stations involved in the detection of an event. In particular, leveraging past experience, an analyst can say that an event located in a certain part of the world is expected to be detected by Stations A, B, and C. Implicit in this statement is that such an event would usually not be detected by Stations X, Y, or Z. For some well understood parts of the world, the absence of one or more "expected" stations—or the presence of one or more "unexpected" stations—is correlated with a hypothesized event's legitimacy and to its survival to the event bulletin. The primary objective of this research is to formalize and quantify the difference between the observed set of stations detecting some hypothesized event, versus the expected set of stations historically associated with detecting similar nearby events close in magnitude. This Station Set Residual can be quantified in many ways, some of which are correlated with the analysts' determination of whether or not the event is valid. We propose that this Station Set Residual score can be used to screen out certain classes of "false" events produced by automatic processing with a high degree of confidence, reducing the analyst burden. Moreover, we propose that the visualization of the historically expected distribution of detecting stations can be immediately useful as an analyst aid during their review process.

Weather Radar Stations

Data.gov (United States)

Department of Homeland Security — These data represent Next-Generation Radar (NEXRAD) and Terminal Doppler Weather Radar (TDWR) weather radar stations within the US. The NEXRAD radar stations are...

Engineered Barrier System - Mechanical Integrity of KBS-3 Spent Fuel Canisters. Report from a Workshop. Synthesis and extended abstracts

Energy Technology Data Exchange (ETDEWEB)

2007-09-15

SKI is preparing to review the license applications being developed by the Swedish Nuclear Fuel and Waste Management Company (SKB) for a final repository for the geological disposal of spent nuclear fuel in the year 2009. As part of its preparation, SKI is conducting a series of technical workshops on key aspects of the Engineered Barrier System (EBS). The workshop reported here mainly dealt with the mechanical integrity of KBS-3 spent fuel canisters. This included assessment and review of various loading conditions, structural integrity models and mechanical properties of the copper shell and the cast iron insert. Degradation mechanisms such as stress corrosion cracking and brittle creep fracture were also briefly addressed. Previous workshops have addressed the overall concept for long-term integrity of the EBS, the manufacturing, testing and QA of the EBS, the performance confirmation for the EBS, long-term stability of the buffer and the backfill, corrosion properties of copper canisters and the spent fuel dissolution and source term modelling. The goal of ongoing review work in connection of the workshop series is to achieve a comprehensive overview of all aspects of SKB's EBS and spent fuel work prior to the handling of the forthcoming license application. This report aims to summarise the issues discussed at the workshop and to extract the essential viewpoints that have been expressed. The report is not a comprehensive record of all the discussions at the workshop, and individual statements made by workshop participants should be regarded as personal opinions rather than SKI viewpoints. Results from the EBS workshops series will be used as one important basis in future review work. This reports includes in addition to the workshop synthesis, questions to SKB identified prior to the workshop, and extended abstracts for introductory presentations

Ichthyoplankton (biological) data collected aboard the NOAA ship Nancy Foster during cruise 0903

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Station data and ichthyoplankton (biological) data from cruise 0903 from the US Virgin Islands, British Virgin Islands, Puerto Rico, Anegada Passage, Leeward Islands...

UMTS Network Stations

Science.gov (United States)

Hernandez, C.

2010-09-01

The weakness of small island electrical grids implies a handicap for the electrical generation with renewable energy sources. With the intention of maximizing the installation of photovoltaic generators in the Canary Islands, arises the need to develop a solar forecasting system that allows knowing in advance the amount of PV generated electricity that will be going into the grid, from the installed PV power plants installed in the island. The forecasting tools need to get feedback from real weather data in "real time" from remote weather stations. Nevertheless, the transference of this data to the calculation computer servers is very complicated with the old point to point telecommunication systems that, neither allow the transfer of data from several remote weather stations simultaneously nor high frequency of sampling of weather parameters due to slowness of the connection. This one project has developed a telecommunications infrastructure that allows sensorizadas remote stations, to send data of its sensors, once every minute and simultaneously, to the calculation server running the solar forecasting numerical models. For it, the Canary Islands Institute of Technology has added a sophisticated communications network to its 30 weather stations measuring irradiation at strategic sites, areas with high penetration of photovoltaic generation or that have potential to host in the future photovoltaic power plants connected to the grid. In each one of the stations, irradiance and temperature measurement instruments have been installed, over inclined silicon cell, global radiation on horizontal surface and room temperature. Mobile telephone devices have been installed and programmed in each one of the weather stations, which allow the transfer of their data taking advantage of the UMTS service offered by the local telephone operator. Every minute the computer server running the numerical weather forecasting models receives data inputs from 120 instruments distributed

Streamflow Gaging Stations

Data.gov (United States)

Department of Homeland Security — This map layer shows selected streamflow gaging stations of the United States, Puerto Rico, and the U.S. Virgin Islands, in 2013. Gaging stations, or gages, measure...

Ocean Station Vessel

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Ocean Station Vessels (OSV) or Weather Ships captured atmospheric conditions while being stationed continuously in a single location. While While most of the...

A Decade of Life Sciences Experiment Unique Equipment Development for Spacelab and Space Station, 1990-1999

Science.gov (United States)

Savage, Paul D.; Connolly, J. P.; Navarro, B. J.

1999-01-01

Ames Research Center's Life Sciences Division has developed and flown an extensive array of spaceflight experiment unique equipment (EUE) during the last decade of the twentieth century. Over this ten year span, the EUE developed at ARC supported a vital gravitational biology flight research program executed on several different platforms, including the Space Shuttle, Spacelab, and Space Station Mir. This paper highlights some of the key EUE elements developed at ARC and flown during the period 1990-1999. Resulting lessons learned will be presented that can be applied to the development of similar equipment for the International Space Station.

Whole genome association study identifies regions of the bovine genome and biological pathways involved in carcass trait performance in Holstein-Friesian cattle.

Science.gov (United States)

Doran, Anthony G; Berry, Donagh P; Creevey, Christopher J

2014-10-01

Four traits related to carcass performance have been identified as economically important in beef production: carcass weight, carcass fat, carcass conformation of progeny and cull cow carcass weight. Although Holstein-Friesian cattle are primarily utilized for milk production, they are also an important source of meat for beef production and export. Because of this, there is great interest in understanding the underlying genomic structure influencing these traits. Several genome-wide association studies have identified regions of the bovine genome associated with growth or carcass traits, however, little is known about the mechanisms or underlying biological pathways involved. This study aims to detect regions of the bovine genome associated with carcass performance traits (employing a panel of 54,001 SNPs) using measures of genetic merit (as predicted transmitting abilities) for 5,705 Irish Holstein-Friesian animals. Candidate genes and biological pathways were then identified for each trait under investigation. Following adjustment for false discovery (q-value carcass traits using a single SNP regression approach. Using a Bayesian approach, 46 QTL were associated (posterior probability > 0.5) with at least one of the four traits. In total, 557 unique bovine genes, which mapped to 426 human orthologs, were within 500kbs of QTL found associated with a trait using the Bayesian approach. Using this information, 24 significantly over-represented pathways were identified across all traits. The most significantly over-represented biological pathway was the peroxisome proliferator-activated receptor (PPAR) signaling pathway. A large number of genomic regions putatively associated with bovine carcass traits were detected using two different statistical approaches. Notably, several significant associations were detected in close proximity to genes with a known role in animal growth such as glucagon and leptin. Several biological pathways, including PPAR signaling, were

Project JADE. Comparison of repository systems. Executive summary of results

International Nuclear Information System (INIS)

Sandstedt, H.; Pers, K.; Birgersson, Lars; Ageskog, L.; Munier, R.

2001-12-01

KBS-3 has since 1984 been the reference method for disposal of spent fuel in Sweden. Several other methods like WP-Cave, Very Deep Holes and Very Long Holes have been evaluated and compared with KBS-3. Though the methods have been judged to have a high safety potential, KBS-3 has been shown to provide advantages in the combined judgement of 'long-term performance and safety', 'technology' and 'costs'. In the present study, different variants of the KBS-3 method have been analysed and compared with the reference concept KBS-3 V (V for vertical). The variants are: KBS-3 H (H for horizontal) and MLH (medium long holes) - with canisters in a horizontal position, single or in a row respectively. The comparison has been carried out separately for the interim items 'technology', 'long-term performance and safety' and 'costs' respectively. The outcome in each of these comparisons have finally been combined in a ranking. This ranking placed KBS-3 V in the top followed by MLH and KBS-3 H. Vertical deposition of a single canister in one deposition hole, KBS-3 V, is robust as gravity is used for lowering the canister and the bentonite into the deposition hole and since each canister has its own barrier in the near field, which reduces the risk for interference between canisters. The drawback for MLH is the uncertainty about the emplacement technique as well as the impact of weak rock and water leakage into a long deposition hole for several canisters. The advantage is that a smaller volume of rock has to be excavated. This is positive regarding the long-term performance and safety, environmental impact and costs. KBS-3 H does not have the same positive potential. The conclusion of the JADE study is that KBS-3 V should remain as reference concept, and that MLH should be studied further with the aim of clarifying the technical feasibility of emplacement and the means of handling water inflow. It is recommended that KBS-3 H with deposition of a single canister in each hole should

Reference Climatological Stations

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Reference Climatological Stations (RCS) network represents the first effort by NOAA to create and maintain a nationwide network of stations located only in areas...

GSM base station electromagnetic radiation and oxidative stress in rats.

Science.gov (United States)

Yurekli, Ali Ihsan; Ozkan, Mehmed; Kalkan, Tunaya; Saybasili, Hale; Tuncel, Handan; Atukeren, Pinar; Gumustas, Koray; Seker, Selim

2006-01-01

The ever increasing use of cellular phones and the increasing number of associated base stations are becoming a widespread source of nonionizing electromagnetic radiation. Some biological effects are likely to occur even at low-level EM fields. In this study, a gigahertz transverse electromagnetic (GTEM) cell was used as an exposure environment for plane wave conditions of far-field free space EM field propagation at the GSM base transceiver station (BTS) frequency of 945 MHz, and effects on oxidative stress in rats were investigated. When EM fields at a power density of 3.67 W/m2 (specific absorption rate = 11.3 mW/kg), which is well below current exposure limits, were applied, MDA (malondialdehyde) level was found to increase and GSH (reduced glutathione) concentration was found to decrease significantly (p < 0.0001). Additionally, there was a less significant (p = 0.0190) increase in SOD (superoxide dismutase) activity under EM exposure.

Fire Stations - 2007

Data.gov (United States)

Kansas Data Access and Support Center — Fire Station Locations in Kansas Any location where fire fighters are stationed at or based out of, or where equipment that such personnel use in carrying out their...

Fire Stations - 2009

Data.gov (United States)

Kansas Data Access and Support Center — Fire Stations in Kansas Any location where fire fighters are stationed or based out of, or where equipment that such personnel use in carrying out their jobs is...

Integrated microfluidic probe station.

Science.gov (United States)

Perrault, C M; Qasaimeh, M A; Brastaviceanu, T; Anderson, K; Kabakibo, Y; Juncker, D

2010-11-01

The microfluidic probe (MFP) consists of a flat, blunt tip with two apertures for the injection and reaspiration of a microjet into a solution--thus hydrodynamically confining the microjet--and is operated atop an inverted microscope that enables live imaging. By scanning across a surface, the microjet can be used for surface processing with the capability of both depositing and removing material; as it operates under immersed conditions, sensitive biological materials and living cells can be processed. During scanning, the MFP is kept immobile and centered over the objective of the inverted microscope, a few micrometers above a substrate that is displaced by moving the microscope stage and that is flushed continuously with the microjet. For consistent and reproducible surface processing, the gap between the MFP and the substrate, the MFP's alignment, the scanning speed, the injection and aspiration flow rates, and the image capture need all to be controlled and synchronized. Here, we present an automated MFP station that integrates all of these functionalities and automates the key operational parameters. A custom software program is used to control an independent motorized Z stage for adjusting the gap, a motorized microscope stage for scanning the substrate, up to 16 syringe pumps for injecting and aspirating fluids, and an inverted fluorescence microscope equipped with a charge-coupled device camera. The parallelism between the MFP and the substrate is adjusted using manual goniometer at the beginning of the experiment. The alignment of the injection and aspiration apertures along the scanning axis is performed using a newly designed MFP screw holder. We illustrate the integrated MFP station by the programmed, automated patterning of fluorescently labeled biotin on a streptavidin-coated surface.

[STEM on Station Education

Science.gov (United States)

Lundebjerg, Kristen

2016-01-01

The STEM on Station team is part of Education which is part of the External Relations organization (ERO). ERO has traditional goals based around BHAG (Big Hairy Audacious Goal). The BHAG model is simplified to a saying: Everything we do stimulates actions by others to advance human space exploration. The STEM on Station education initiate is a project focused on bringing off the earth research and learning into classrooms. Educational resources such as lesson plans, activities to connect with the space station and STEM related contests are available and hosted by the STEM on Station team along with their partners such as Texas Instruments. These educational activities engage teachers and students in the current happenings aboard the international space station, inspiring the next generation of space explorers.

Station History Of The Seismic Station In Ahmadu Bello University ...

African Journals Online (AJOL)

Dominants in the selected events are events from Meditterranian, East Kazakhstan, India/Burma/China, South and Central America and North Ascension island regions. The limited number of events reporting at the station was due to low operational gain at the station which permitted only events whose magnitudes are ...

Impacts of Zayandehroud Dam on the Macro-benthic Invertebrate and Water Quality of Zayandehroud River using BMWP and ASPT Biological Indices

Directory of Open Access Journals (Sweden)

H. Ebrahimi Dastgerdi

2017-09-01

Full Text Available Dams provide benefits for human societies, but now they are considered as one of the most important factors influencing habitat degradation and changing the hydrological water flow. In order to study the ecological effects of Zayandehroud Dam on the benthic communities and water quality of Zayandehroud river, six sampling stations were selected on the river substrate using biological indicators such as BMWP (Biological Monitoring Working Party and ASPT(Average Score Per Taxa. Then, a quantitative survey of the macro- benthic invertebrates fauna was conducted with 3 replications at each station, from July to June 2014 with a 45- day interval period. The identified macro-benthic invertebrates belonged to 31 families, 16 orders and 7 classes. The results of BMWP index showed significant differences among sampling stations (p<0.001, and significant difference between seasons in all stations except Overgan station (p<0.05. ASPT index also revealed significant differences among the stations (p<0.01. In addition, the results of Shannon diversity index indicated that Zayanderoud Dam construction, has changed diversity and composition of downstream benthic communities due to alterations in the depth and speed of the water flow, as well as substrate structure.

The Trencin water power station

International Nuclear Information System (INIS)

2005-01-01

This leaflet describes the Trencin water power station. The Trencin water power station was built seven years after the Dubnica nad Vahom water power station started its operation and was the last stage of the first and the oldest derived cascade of water power stations on the Vah River. After completing water power stations at Ladce (1936), Ilava (1946) and Dubnica nad Vahom (1949) and before constructing the Trencin water power station, the whole second derived cascade of water power stations including water power stations at Kostolna, Nove Mesto nad Vahom and Horna Streda was built as soon as possible mainly because the need to get compensation for discontinued electricity supplies as well as energetic coal from the Czech Republic. Hereby, experiences from the construction of previous grades were used, mainly as far as the dimensioning was concerned, as the fi rst installed power stations had, in comparison with the growing requirements on the electricity supplies, very low absorption capacity - only 150 m 3 .s -1 . Thus the Trencin power station (original name was the Skalka power station) was already dimensioned for the same absorption capacity as the cascade located downstream the river, that is 180 m 3 .s -1 . That was related also to growing demands on electricity supplies during the peaks in the daily electric system load diagram, and thus to the transfer from continuous operation of the water power station to semi-peak or even peak performance. According to the standards of power station classification, the Trencin water power station is a medium size, low pressure, channel power station with two units equipped by Kaplan turbines and synchronous hydro-alternators. The water power station installed capacity is 16.1 MW in total and its designed annual production of electrical energy for medium water year is 85,000 MWh, while the average annual production during the last 30 years is 86,252 MWh. Installed unit has a four-blade Kaplan turbine with the diameter

Tether applications for space station

Science.gov (United States)

Nobles, W.

1986-01-01

A wide variety of space station applications for tethers were reviewed. Many will affect the operation of the station itself while others are in the category of research or scientific platforms. One of the most expensive aspects of operating the space station will be the continuing shuttle traffic to transport logistic supplies and payloads to the space station. If a means can be found to use tethers to improve the efficiency of that transportation operation, it will increase the operating efficiency of the system and reduce the overall cost of the space station. The concept studied consists of using a tether to lower the shuttle from the space station. This results in a transfer of angular momentum and energy from the orbiter to the space station. The consequences of this transfer is studied and how beneficial use can be made of it.

Virtual Knowledge Brokering: Describing the Roles and Strategies Used by Knowledge Brokers in a Pediatric Physiotherapy Virtual Community of Practice.

Science.gov (United States)

Hurtubise, Karen; Rivard, Lisa; Héguy, Léa; Berbari, Jade; Camden, Chantal

2016-01-01

Knowledge transfer in pediatric rehabilitation is challenging and requires active, multifaceted strategies. The use of knowledge brokers (KBs) is one such strategy noted to promote clinician behavior change. The success of using KBs to transfer knowledge relies on their ability to adapt to ever-changing clinical contexts. In addition, with the rapid growth of online platforms as knowledge transfer forums, KBs must become effective in virtual environments. Although the role of KBs has been studied in various clinical contexts, their emerging role in specific online environments designed to support evidence-based behavior change has not yet been described. Our objective is to describe the roles of, and strategies used by, four KBs involved in a virtual community of practice to guide and inform future online KB interventions. A descriptive design guided this study and a thematic content analysis process was used to analyze online KB postings. The Promoting Action on Research in Health Sciences knowledge transfer framework and online andragogical learning theories assisted in the coding. A thematic map was created illustrating the links between KBs' strategies and emerging roles in the virtual environment. We analyzed 95 posts and identified three roles: 1) context architect: promoting a respectful learning environment, 2) knowledge sharing promoter: building capacity, and 3) linkage creator: connecting research-to-practice. Strategies used by KBs reflected invitational, constructivism, and connectivism approaches, with roles and strategies changing over time. This study increases our understanding of the actions of KBs in virtual contexts to foster uptake of research evidence in pediatric physiotherapy. Our results provide valuable information about the knowledge and skills required by individuals to fulfill this role in virtual environments.

Canister displacement in KBS-3V. A theoretical study

Energy Technology Data Exchange (ETDEWEB)

Boergesson, Lennart [Clay Technology AB, Lund (Sweden); Hernelind, Jan [FEMTech AB, Vaesteraas (Sweden)

2006-02-15

The vertical displacement of the canister in the KBS-3V concept has been studied in a number of consolidation and creep calculations using the FE-program ABAQUS. The creep model used for the calculations is based on Singh-Mitchell's creep theory, which has been adapted to and verified for the buffer material MX-80 in earlier tests. A porous elastic model with Drucker-Prager plasticity has been used for the consolidation calculations. For simplicity the buffer has been assumed to be water saturated from start. In one set of calculations only the consolidation and creep in the buffer without considering the interaction with the backfill was studied. In the other set of calculations the interaction with the backfill was included for a backfill consisting of an in situ compacted mixture of 30% bentonite and 70% crushed rock. The motivation to also study the behaviour of the buffer alone was that the final choice of backfill material and backfilling technique is not made yet so that set of calculations simulates a backfill that has identical properties with the buffer. The two cases represent two extreme cases, one with a backfill that has a low stiffness and the lowest allowable swelling pressure and one that has the highest possible swelling pressure and stiffness. The base cases in the calculations correspond to the final average density at saturation of 2,000 kg/m{sup 3} with the expected swelling pressure of 7 MPa in a buffer. In order to study the sensitivity of the system to loss in bentonite mass and swelling pressure seven additional calculations were done with reduced swelling pressure down to 80 kPa corresponding to a density at water saturation of about 1,500 kg/m{sup 3}. The calculations included two stages, where the first stage models the swelling and consolidation that takes place in order for the buffer to reach force equilibrium. This stage takes place during the saturation phase and the subsequent consolidation/swelling phase. The second stage

Canister displacement in KBS-3V. A theoretical study

International Nuclear Information System (INIS)

Boergesson, Lennart; Hernelind, Jan

2006-02-01

The vertical displacement of the canister in the KBS-3V concept has been studied in a number of consolidation and creep calculations using the FE-program ABAQUS. The creep model used for the calculations is based on Singh-Mitchell's creep theory, which has been adapted to and verified for the buffer material MX-80 in earlier tests. A porous elastic model with Drucker-Prager plasticity has been used for the consolidation calculations. For simplicity the buffer has been assumed to be water saturated from start. In one set of calculations only the consolidation and creep in the buffer without considering the interaction with the backfill was studied. In the other set of calculations the interaction with the backfill was included for a backfill consisting of an in situ compacted mixture of 30% bentonite and 70% crushed rock. The motivation to also study the behaviour of the buffer alone was that the final choice of backfill material and backfilling technique is not made yet so that set of calculations simulates a backfill that has identical properties with the buffer. The two cases represent two extreme cases, one with a backfill that has a low stiffness and the lowest allowable swelling pressure and one that has the highest possible swelling pressure and stiffness. The base cases in the calculations correspond to the final average density at saturation of 2,000 kg/m 3 with the expected swelling pressure of 7 MPa in a buffer. In order to study the sensitivity of the system to loss in bentonite mass and swelling pressure seven additional calculations were done with reduced swelling pressure down to 80 kPa corresponding to a density at water saturation of about 1,500 kg/m 3 . The calculations included two stages, where the first stage models the swelling and consolidation that takes place in order for the buffer to reach force equilibrium. This stage takes place during the saturation phase and the subsequent consolidation/swelling phase. The second stage models the

CITRA PERUSAHAAN DALAM BERITA KRISIS PERUSAHAAN: Konstruksi Citra Perusahaan Daerah Taman Satwa (PDTS Kebun Binatang Surabaya dalam Teks Berita Kematian Michael di Harian Jawa Pos dan Sindo

Directory of Open Access Journals (Sweden)

Theresia Intan Putri Hartiana

2014-12-01

Full Text Available Penelitian ini dilakukan untuk melihat bagaimana Harian Jawa Pos dan Sindo membentuk citra Perusahaan Daerah Taman Satwa (PDTS Kebun Binatang Surabaya (KBS dikonstruksikan dalam berita krisis kematian Michael. Metode yang digunakan dalam penelitian ini adalah framing Entman dengan merujuk pada pemberian definisi, penelasan, evaluasi, dan rekomendasi acana untuk melihat penekanan pada kerangka berpikir terhadap peristiwa yang dicanangkan. Citra PDTS KBS dalam Harian Jawa Pos memperlihatkan adanya kondisi Kebun Binatang Surabaya sudah tidak layak bagi satwanya dan kesengajaan keterlibatan orang dalam menjadi penyebab kematian Singa KBS mati tergantung. Citra PDTS KBS oleh Koran Sindo ditampilkan sebagai pihak yang harus bertanggungjawab atas kelalaian dan kecerobohannya dalam memelihara satwa sehingga mengakibatkan terjadi kematian satwa yang tidak wajar. Hal tersebut terlihat dari analisis makrostruktur teks yang memaparkan bahwa kepolisian dilibatkan untuk menyelidiki singa yang mati tergantung akibat kelalaian PDTS KBS dalam pengelolaan satwa. Pemberitaan yang dimunculkan oleh media massa patut menjadi perhatian oleh praktisi Public Relations. Berita yang dikonstruksi negatif secara terus menerus dapat memberikan pengaruh negatif pula di dalam benak pembaca. Beberapa pernyataan negatif yang muncul dalam teks pemberitaan dapat dijadikan sebagai dasar perencanaan bagi humas PDTS KBS dalam penanganan krisis dan perbaikan citra setelah krisis.

Mobile environmental radiation monitoring station

International Nuclear Information System (INIS)

Assido, H.; Shemesh, Y.; Mazor, T.; Tal, N.; Barak, D.

1997-01-01

A mobile environmental radiation monitoring station has been developed and established for the Israeli Ministry of Environment. The radiation monitoring station is ready for immediate placing in any required location, or can be operated from a vehicle. The station collects data Tom the detector and transfers it via cellular communication network to a Computerized Control Center for data storage, processing, and display . The mobile station is fully controlled from the. Routinely, the mobile station responses to the data request accumulated since the last communication session. In case of fault or alarm condition in the mobile station, a local claim is activated and immediately initiates communication with the via cellular communication network. (authors)

CDIP Station Data Collection - All Stations

Data.gov (United States)

Scripps Institution of Oceanography, UC San Diego — The Coastal Data Information Program's station data collection consists of all publicly-released coastal environment measurements taken over the program's history, a...

Fundamental Space Biology-1: HHR and Incubator for ISS Space Life Sciences

Science.gov (United States)

Kirven-Brooks, M.; Fahlen, T.; Sato, K.; Reiss-Bubenheim, D.

The Space Station Biological Research Project (SSBRP) is developing an Incubator and a Habitat Holding Rack (HHR) to support life science experiments aboard the International Space Station (ISS). The HHR provides for cooling and power needs, and supports data transfer (including telemetry, commanding, video processing, Ethernet), video compression, and data and command storage). The Incubator is a habitat that provides for controlled temperature between +4 C and +45 C and air circulation. It has a set of connector ports for power, analog and digital sensors, and video pass-through to support experiment-unique hardware within the Incubator specimen chamber. The Incubator exchanges air with the ISS cabin. The Fundamental Space Biology-1 (FSB-1) Project will be delivering, the HHR and two Incubators to ISS. The two inaugural experiments to be conducted on ISS using this hardware will investigate the biological effects of the space environment on two model organisms, Saccharomyces cerevisiae (S. cerevisiae; yeast) and Caenorhabditis elegans (C. elegans; nematode). The {M}odel {Y}east {C}ultures {o}n {S}tation (MYCOS) experiment will support examination of the effect of microgravity and cosmic radiation on yeast biology. In the second series of experiments during the same increment, the effects of microgravity and space environment radiation on C. elegans will be examined. The {F}undamental Space Biology {I}ncubator {E}xperiment {R}esearch using {C}. {e}legans (FIERCE) study is designed to support a long duration, multi-generational study of nematodes. FIERCE on-orbit science operations will include video monitoring, sub-culturing and periodic fixation and freezing of samples. For both experiments, investigators will be solicited via an International Space Life Sciences Research Announcement. In the near future, the Centrifuge Accommodation Module will be delivered to ISS, which will house the SSBRP 2.5 m Centrifuge Rotor. The Incubator can be placed onto the Centrifuge

Preparing the Plate Boundary Observatory GNSS Network for the Future

Science.gov (United States)

Austin, K. E.; Walls, C. P.; Dittman, T.; Mann, D.; Boyce, E. S.; Basset, A.; Woolace, A. C.; Turner, R.; Lawrence, S.; Rhoades, S.; Pyatt, C.; Willoughby, H.; Feaux, K.; Mattioli, G. S.

2017-12-01

The EarthScope Plate Boundary Observatory (PBO) GNSS network, funded by the NSF and operated by UNAVCO, is comprised of 1100 permanent GPS and GNSS stations spanning three principal tectonic regimes and is administered by distinct management. The GPS-only network was initially designed for daily data file downloads primarily for tectonic analysis. This low data volume requirement and circa-2004 IP-based cellular/VSat modems provided significant freedom for station placement and enabled science-targeted installation of stations in some of the most remote and geologically interesting areas. Community requests for high-rate data downloads for GNSS seismology, airborne LiDAR surveys, meteorological/GNSS/seismic real-time data flow and other demands, however, require significantly increased bandwidth beyond the 5-20 kB/s transfer rates that were needed as part of the original design. Since the close of construction in September 2008, PBO enhancements have been implemented through additional funding by the NSF (ARRA/Cascadia), NOAA, and NASA and in collaboration with stakeholders such as Caltrans, ODOT, Scripps, and the USGS. Today, only 18 of the original cell modems remain, with 601 upgraded cell modems providing 3G/4G/LTE data communications that support transfer rates ranging from 80-400 kB/s. Radio network expansion and upgrades continue to harden communications using both 2.4 GHz and 5.8 GHz radios. 78 VSAT and 5 manual download sites remain. PBO-wide the network capabilities for 1 Hz & 5 Hz downloads or low latency 1 Hz streaming are 85%, 80% and 65% of PBO stations, respectively, with 708 active 1 Hz streams. Vaisala meteorological instruments are located at 140 sites most of which stream GPS/Met data in real time. GPS-only receivers are being replaced with GNSS receivers and antennas. Today, there are 279 stations in the PBO network with either GLONASS enabled Trimble NetR9 or full GNSS constellation Septentrio PolaRx5 receivers. Just as the scale and

A customer-friendly Space Station

Science.gov (United States)

Pivirotto, D. S.

1984-01-01

This paper discusses the relationship of customers to the Space Station Program currently being defined by NASA. Emphasis is on definition of the Program such that the Space Station will be conducive to use by customers, that is by people who utilize the services provided by the Space Station and its associated platforms and vehicles. Potential types of customers are identified. Scenarios are developed for ways in which different types of customers can utilize the Space Station. Both management and technical issues involved in making the Station 'customer friendly' are discussed.

Application of the k{sub 0}-INAA method for analysis of biological samples at the pneumatic station of the IEA-R1 nuclear research reactor

Energy Technology Data Exchange (ETDEWEB)

Puerta, Daniel C.; Figueiredo, Ana Maria G.; Semmler, Renato, E-mail: dcpuerta@hotmail.com, E-mail: anamaria@ipen.br, E-mail: rsemmler@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Jacimovic, Radojko, E-mail: radojko.jacimovic@ijs.si [Jozef Stefan Institute (JSI), Ljubljana, LJU (Slovenia). Department of Environmental Sciences

2013-07-01

As part of the process of implementation of the k{sub 0}-INAA standardization method at the Neutron Activation Laboratory (LAN-IPEN), Sao Paulo, Brazil, this study presents the results obtained for the analysis of short and medium-lived nuclides in biological samples by k{sub 0}-INAA using the program k{sub 0}-IAEA, provided by the International Atomic Energy Agency (IAEA). The elements Al, Ba, Br, Na, K, Mn, Mg, Sr and V were determined with respect to gold ({sup 197}Au) using the pneumatic station facility of the IEA-R1 4.5 MW swimming pool nuclear research reactor, Sao Paulo. Characterization of the pneumatic station was carried out by using the 'bare triple-monitor' method with {sup 197}Au-{sup 96}Zr-{sup 94}Zr. The Certified Reference Material IRMM-530R Al-0.1%Au alloy and high purity zirconium comparators were used. The efficiency curves of the gamma-ray spectrometer used were determined by measuring calibrated radioactive sources at the usually utilized counting geometries. The method was validated by analyzing the reference materials NIST SRM 1547 Peach Leaves, INCT-MPH-2 Mixed Polish Herbs and NIST SRM 1573a Tomato Leaves. The concentration results obtained agreed with certified, reference and recommended values, showing relative errors (bias, %) less than 30% for most elements. The Coefficients of Variation were below 20%, showing a good reproducibility of the results. The E{sub n}-number showed that all results, except Na in NIST SRM 1547 and NIST SRM 1573a and Al in INCT-MPH-2, were within 95% confidence interval. (author)

Mussel beds are biological power stations on intertidal flats

Science.gov (United States)

Engel, Friederike G.; Alegria, Javier; Andriana, Rosyta; Donadi, Serena; Gusmao, Joao B.; van Leeuwe, Maria A.; Matthiessen, Birte; Eriksson, Britas Klemens

2017-05-01

Intertidal flats are highly productive areas that support large numbers of invertebrates, fish, and birds. Benthic diatoms are essential for the function of tidal flats. They fuel the benthic food web by forming a thin photosynthesizing compartment in the top-layer of the sediment that stretches over the vast sediment flats during low tide. However, the abundance and function of the diatom film is not homogenously distributed. Recently, we have realized the importance of bivalve reefs for structuring intertidal ecosystems; by creating structures on the intertidal flats they provide habitat, reduce hydrodynamic stress and modify the surrounding sediment conditions, which promote the abundance of associated organisms. Accordingly, field studies show that high chlorophyll a concentration in the sediment co-vary with the presence of mussel beds. Here we present conclusive evidence by a manipulative experiment that mussels increase the local biomass of benthic microalgae; and relate this to increasing biomass of microalgae as well as productivity of the biofilm across a nearby mussel bed. Our results show that the ecosystem engineering properties of mussel beds transform them into hot spots for primary production on tidal flats, highlighting the importance of biological control of sedimentary systems.

The Miksova water power station

International Nuclear Information System (INIS)

2005-01-01

This leaflet describes the Miksova water power station. The Miksova water power station is part of the second derived cascade of hydro power stations on the river Vah. It was built at the end of a huge development in Slovak hydro-energy in the late 1950's and the beginning of the 1960's. It is the second water power station on this derived cascade, which is situated downstream the Hricov reservoir and water power station. At the power station, three turbine sets with vertical Kaplan turbines are installed with a total power output of 3 x 31.2 = 93.6 MW. With this power output the Miksova water power station (Miksova I) was the biggest water power station in the Slovak Republic until the construction of Pumping water power station Liptovska Mara. And it is still the biggest channel water power station on the Vah so far. It was put into operation during the period 1963 to 1965. There are three turbine sets with Kaplan turbines from CKD Blansko, with a synchronous hydro-alternator installed in the power station. Their installed capacity is 93.6 MW in total and the projected annual production of electrical energy is 207 GWh. The turbines are fi ve-bladed (on the Hricov and Povazska Bystrica water power stations they are four-bladed) and the impeller wheel has a diameter of 4800 mm. They are designed for extension of the head from 24.1 to 22.21 m and each of them has an absorption capacity of 134 m 3 .s -1 nd a nominal operating speed of 2.08 m 3 .s -1 , runaway speed 4.9 m 3 .s -1 . Each synchronous hydro-alternator has a maximum power output of 31.2 MW, a nominal voltage of 10.5 kV and power factor cos φ of 0.8. Power from the power station is led out through 110 kV switchgear. The water power station operates under automatic turbine mode of operation with remote indication and control from the Dispatch Centre at Vodne elektrarne, in Trencin. From start of operation until the end of 2003 all three turbine sets operated for a total of 450,500 running hours and the

Radiation safety of mobile phones and base stations

International Nuclear Information System (INIS)

Jokela, K.; Leszczynski, D.; Paile, W.; Salomaa, S.; Puranen, L.; Hyysalo, P.

1997-06-01

The recent expansion of personal telecommunications has led to a rapid increase in the exposure of people to the radio-frequency (RF) radiation. Although the mobile phones are low power devices, the antenna is so close to the head that the local exposure may slightly exceed 2 W/kg, the current exposure limit for the local specific absorption rate SAR for the general public. The increase in the temperature is, however, too small to have any physiological significance. On the basis of experiments with cell cultures it is possible that other biological effects caused by some unknown non-thermal mechanism exist, but thus far there is conclusive biological or epidemiological evidence to suggest any diseases adverse physiological changes below the thermal threshold. The use of a mobile phone by a person wearing a pace-maker, the immunity which against the electromagnetic interference from the mobile phone has not be assured, is not recommended. The exposure caused by the base stations is in almost all practical ceases all below the power density limits for general public. (orig.) (115 refs.)

Space station propulsion requirements study

Science.gov (United States)

Wilkinson, C. L.; Brennan, S. M.

1985-01-01

Propulsion system requirements to support Low Earth Orbit (LEO) manned space station development and evolution over a wide range of potential capabilities and for a variety of STS servicing and space station operating strategies are described. The term space station and the overall space station configuration refers, for the purpose of this report, to a group of potential LEO spacecraft that support the overall space station mission. The group consisted of the central space station at 28.5 deg or 90 deg inclinations, unmanned free-flying spacecraft that are both tethered and untethered, a short-range servicing vehicle, and a longer range servicing vehicle capable of GEO payload transfer. The time phasing for preferred propulsion technology approaches is also investigated, as well as the high-leverage, state-of-the-art advancements needed, and the qualitative and quantitative benefits of these advancements on STS/space station operations. The time frame of propulsion technologies applicable to this study is the early 1990's to approximately the year 2000.

Hydrogen Station Cost Estimates: Comparing Hydrogen Station Cost Calculator Results with other Recent Estimates

Energy Technology Data Exchange (ETDEWEB)

Melaina, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Penev, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2013-09-01

This report compares hydrogen station cost estimates conveyed by expert stakeholders through the Hydrogen Station Cost Calculation (HSCC) to a select number of other cost estimates. These other cost estimates include projections based upon cost models and costs associated with recently funded stations.

Gas Stations, US, 2010, NAVTEQ

Data.gov (United States)

U.S. Environmental Protection Agency — The Gas_Stations dataset is derived from the Navteq 'AUTOSVC' SDC layer (FAC_TYPE=5540) and contains gas stations and petrol stations. This NAVTEQ dataset is...

Non-Coop Station History (Unindexed)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Station history documentation for stations outside the US Cooperative Observer network. Documents should be compared with those in the Non-Coop Station History...

Single-Station Sigma for the Iranian Strong Motion Stations

Science.gov (United States)

Zafarani, H.; Soghrat, M. R.

2017-11-01

In development of ground motion prediction equations (GMPEs), the residuals are assumed to have a log-normal distribution with a zero mean and a standard deviation, designated as sigma. Sigma has significant effect on evaluation of seismic hazard for designing important infrastructures such as nuclear power plants and dams. Both aleatory and epistemic uncertainties are involved in the sigma parameter. However, ground-motion observations over long time periods are not available at specific sites and the GMPEs have been derived using observed data from multiple sites for a small number of well-recorded earthquakes. Therefore, sigma is dominantly related to the statistics of the spatial variability of ground motion instead of temporal variability at a single point (ergodic assumption). The main purpose of this study is to reduce the variability of the residuals so as to handle it as epistemic uncertainty. In this regard, it is tried to partially apply the non-ergodic assumption by removing repeatable site effects from total variability of six GMPEs driven from the local, Europe-Middle East and worldwide data. For this purpose, we used 1837 acceleration time histories from 374 shallow earthquakes with moment magnitudes ranging from M w 4.0 to 7.3 recorded at 370 stations with at least two recordings per station. According to estimated single-station sigma for the Iranian strong motion stations, the ratio of event-corrected single-station standard deviation ( Φ ss) to within-event standard deviation ( Φ) is about 0.75. In other words, removing the ergodic assumption on site response resulted in 25% reduction of the within-event standard deviation that reduced the total standard deviation by about 15%.

Central Station Design Options

DEFF Research Database (Denmark)

2011-01-01

. The work identifies the architecture, sizing and siting of prospective Central Stations in Denmark, which can be located at shopping centers, large car parking lots or gas stations. Central Stations are planned to be integrated in the Danish distribution grid. The Danish island of Bornholm, where a high...... overloading, more reference points might be necessary to represent various transformer loading levels. The subject of safety in Central Station is also addressed. A number of safety rules based on European standards apply to AC charging equipment up to 44 kW. The connection interlock and the automatic de......-energization are identified as fundamental requirements for safety in such a charging station. The connection interlock is a solution which ensures that no power is applied to the DC cable when the EV connector is not connected. The automatic de-energization device ensures that whenever a strain on the cable is detected, e...

Enhanced Master Station History Report

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Enhanced Master Station History Report (EMSHR) is a compiled list of basic, historical information for every station in the station history database, beginning...

SPS rectifier stations

CERN Multimedia

CERN PhotoLab

1974-01-01

The first of the twelves SPS rectifier stations for the bending magnets arrived at CERN at the end of the year. The photograph shows a station with the rectifiers on the left and in the other three cubicles the chokes, capacitors and resistor of the passive filter.

47 CFR 97.109 - Station control.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Station control. 97.109 Section 97.109... SERVICE Station Operation Standards § 97.109 Station control. (a) Each amateur station must have at least one control point. (b) When a station is being locally controlled, the control operator must be at the...

Power station instrumentation

International Nuclear Information System (INIS)

Jervis, M.W.

1993-01-01

Power stations are characterized by a wide variety of mechanical and electrical plant operating with structures, liquids and gases working at high pressures and temperatures and with large mass flows. The voltages and currents are also the highest that occur in most industries. In order to achieve maximum economy, the plant is operated with relatively small margins from conditions that can cause rapid plant damage, safety implications, and very high financial penalties. In common with other process industries, power stations depend heavily on control and instrumentation. These systems have become particularly significant, in the cost-conscious privatized environment, for providing the means to implement the automation implicit in maintaining safety standards, improving generation efficiency and reducing operating manpower costs. This book is for professional instrumentation engineers who need to known about their use in power stations and power station engineers requiring information about the principles and choice of instrumentation available. There are 8 chapters; chapter 4 on instrumentation for nuclear steam supply systems is indexed separately. (Author)

Final Bioventing Pilot Test Work Plan for Base Exchange Service Station Underground Storage Tank Area, Vandenberg Air Force Base, California. Part I

National Research Council Canada - National Science Library

1992-01-01

This pilot test work plan presents the scope of an in situ enhanced biological degradation, or "bioventing", pilot test for treatment of gasoline- contaminated soils at the Base Exchange Service Station (BXSS...

Investigation of the electromagnetic radiation fields from the Sabborah radio broadcasting station and comparing it with the ICNIRP recommended limits

International Nuclear Information System (INIS)

Kharita, M.H.; AboKasem, I.

2007-04-01

This study concerns a radio emission base station which is located near Sabborah, about 20 Km in the west of Damascus. The aim of this study is to investigate the level and the distribution of electromagnetic field in the nearby of this station in order to determine the level of its hazardous biological effect on the worker and the people living nearby. This work is based on two main parts: First, a theoretical part which offer the concept of electromagnetic wave, the emission and measurement of electromagnetic field, the hazardous biological effects and the general guideline for limiting the exposure to electromagnetic field recommended by the International Commission on Non-Ionizing Radiation Protection and the would Health Organization. Finally, an Experimental part which presents the realized measurements of electric field using two electric field strength meters, the results and recommendations.(author)

Station Capacity

DEFF Research Database (Denmark)

Landex, Alex

2011-01-01

the probability of conflicts and the minimum headway times into account. The last method analyzes how optimal platform tracks are used by examining the arrival and departure pattern of the trains. The developed methods can either be used separately to analyze specific characteristics of the capacity of a station......Stations are often limiting the capacity of railway networks. This is due to extra need of tracks when trains stand still, trains turning around, and conflicting train routes. Although stations are often the capacity bottlenecks, most capacity analysis methods focus on open line capacity. Therefore...... for platform tracks and the probability that arriving trains will not get a platform track immediately at arrival. The third method is a scalable method that analyzes the conflicts in the switch zone(s). In its simplest stage, the method just analyzes the track layout while the more advanced stages also take...

Secure base stations

NARCIS (Netherlands)

Bosch, Peter; Brusilovsky, Alec; McLellan, Rae; Mullender, Sape J.; Polakos, Paul

2009-01-01

With the introduction of the third generation (3G) Universal Mobile Telecommunications System (UMTS) base station router (BSR) and fourth generation (4G) base stations, such as the 3rd Generation Partnership Project (3GPP) Long Term Evolution (LTE) Evolved Node B (eNB), it has become important to

OWL2 benchmarking for the evaluation of knowledge based systems.

Directory of Open Access Journals (Sweden)

Sher Afgun Khan

Full Text Available OWL2 semantics are becoming increasingly popular for the real domain applications like Gene engineering and health MIS. The present work identifies the research gap that negligible attention has been paid to the performance evaluation of Knowledge Base Systems (KBS using OWL2 semantics. To fulfil this identified research gap, an OWL2 benchmark for the evaluation of KBS is proposed. The proposed benchmark addresses the foundational blocks of an ontology benchmark i.e. data schema, workload and performance metrics. The proposed benchmark is tested on memory based, file based, relational database and graph based KBS for performance and scalability measures. The results show that the proposed benchmark is able to evaluate the behaviour of different state of the art KBS on OWL2 semantics. On the basis of the results, the end users (i.e. domain expert would be able to select a suitable KBS appropriate for his domain.

Diversidad de Agaricomycetes clavarioides en la Estación de Biología de Chamela, Jalisco, México Diversity of clavarioid Agaricomycetes at the Chamela Biological Station, Jalisco, Mexico

Directory of Open Access Journals (Sweden)

Itzel Ramírez-López

2012-12-01

Full Text Available Este estudio es una contribución al conocimiento de la diversidad y estructura de los Agaricomycetes clavarioides que se desarrollan en los bosques tropicales de la Estación de Biología de Chamela, Jalisco, México. Las recolecciones se realizaron durante la temporada de lluvias de los años 2005 a 2008; se registraron datos de hábitat y morfología de los basidiomas, tipo de vegetación y sustrato donde se desarrollan, así como del patrón de crecimiento, área de distribución, abundancia y orientación e inclinación de las laderas donde se localizaron. Los 86 ejemplares registrados corresponden a 17 especies, de las cuales Physalacria changensis, P. inflata, Pterula verticillata y Scytinopogon scaber son nuevos registros para México. Scytinopogon pallescens, Pterula sp. 2 y Thelephora sp. fueron las más abundantes y 6 especies se registraron sólo 1 vez. Los datos obtenidos indican que la frecuencia con la que se hallan los basidiomas de los clavarioides en los distintos hábitats no es aleatoria, sino que su producción se da preferentemente en las laderas sur con inclinación de 21° a 30° y en el bosque tropical subperennifolio.This study is a contribution to the biodiversity and community structure of clavarioid Agaricomycetes in the tropical forests of the Chamela Biological Station, in Jalisco, Mexico. The collections were made during the rainy seasons from 2005 to 2008 during which we recorded the morphological and ecological information, including basidiocarp morphology and patterns of growth. Likewise, records were also taken for habitat preferences, types of substrate, orientation, slope inclination, range of distribution and abundance. The 86 specimens recorded, corresponded to 17 different species, from which Physalacria changensis, P. inflata, Pterula verticillata and Scytinopogon scaber are new records for Mexico. The species S. pallescens, Pterula sp. 2 and Thelephora sp. were the most abundant, while other 6 species

Data communications method for mobile network in fourth generation communications system, involves delivering decoded data to mobile station from relay station, where mobile station receives data from both relay and base stations

DEFF Research Database (Denmark)

2008-01-01

The method involves utilizing a base station (BS) (100) to transmit data to a relay station (RS) (110) and a mobile station (MS) (120), where the data includes two messages. The BS is utilized to transmit the two messages by utilizing a linear combination method, and the data is received in the RS...

The Swedish Concept for Disposal of Spent Nuclear Fuel: Differences Between Vertical and Horizontal Waste Canister Emplacement

International Nuclear Information System (INIS)

Bennett, D.G.; Hicks, T.W.

2005-10-01

The Swedish Nuclear Power Inspectorate (SKI) is preparing for the review of licence applications related to the disposal of spent nuclear fuel. The Swedish Nuclear Fuel and Waste Management Company (SKB) refers to its proposals for the disposal of spent nuclear fuel as the KBS-3 concept. In the KBS-3 concept, SKB plans that, after 30 to 40 years of interim storage, spent fuel will be disposed of at a depth of about 500 m in crystalline bedrock, surrounded by a system of engineered barriers. The principle barrier to radionuclide release is a cylindrical copper canister. Within the copper canister, the spent fuel is supported by a cast iron insert. Outside the copper canister is a layer of bentonite clay, known as the buffer, which is designed to provide mechanical protection for the canisters and to limit the access of groundwater and corrosive substances to their surfaces. The bentonite buffer is also designed to sorb radionuclides released from the canisters, and to filter any colloids that may form within the waste. SKB is expected to base its forthcoming licence applications on a repository design in which the waste canisters are emplaced in vertical boreholes (KBS-3V). However, SKB has also indicated that it might be possible and, in some respects, beneficial to dispose of the waste canisters in horizontal tunnels (KBS-3H). There are many similarities between the KBS-3V and KBS-3H designs. There are, however, uncertainties associated with both of the designs and, when compared, both possess relative advantages and disadvantages. SKB has identified many of the key factors that will determine the evolution of a KBS-3H repository and has plans for research and development work in many of the areas where the differences between the KBS-3V and KBS-3H designs mean that they could be significant in terms of repository performance. With respect to the KBS-3H design, key technical issues are associated with: 1. The accuracy of deposition drift construction. 2. Water

Waste Transfer Stations

DEFF Research Database (Denmark)

Christensen, Thomas Højlund

2011-01-01

tion and transport is usually the most costly part of any waste management system; and when waste is transported over a considerable distance or for a long time, transferring the waste from the collection vehicles to more efficient transportation may be economically beneficial. This involves...... a transfer station where the transfer takes place. These stations may also be accessible by private people, offering flexibility to the waste system, including facilities for bulky waste, household hazardous waste and recyclables. Waste transfer may also take place on the collection route from small...... describes the main features of waste transfer stations, including some considerations about the economical aspects on when transfer is advisable....

Meyrin Petrol Station

CERN Multimedia

2006-01-01

Please note that the Meyrin petrol station will be closed for maintenance work on Tuesday 19 and Wednesday 20 December 2006. If you require petrol during this period we invite you to use the Prévessin petrol station, which will remain open. TS-IC-LO Section Tel.: 77039 - 73793

Low-flow analysis and selected flow statistics representative of 1930-2002 for streamflow-gaging stations in or near West Virginia

Science.gov (United States)

Wiley, Jeffrey B.

2006-01-01

Five time periods between 1930 and 2002 are identified as having distinct patterns of annual minimum daily mean flows (minimum flows). Average minimum flows increased around 1970 at many streamflow-gaging stations in West Virginia. Before 1930, however, there might have been a period of minimum flows greater than any period identified between 1930 and 2002. The effects of climate variability are probably the principal causes of the differences among the five time periods. Comparisons of selected streamflow statistics are made between values computed for the five identified time periods and values computed for the 1930-2002 interval for 15 streamflow-gaging stations. The average difference between statistics computed for the five time periods and the 1930-2002 interval decreases with increasing magnitude of the low-flow statistic. The greatest individual-station absolute difference was 582.5 percent greater for the 7-day 10-year low flow computed for 1970-1979 compared to the value computed for 1930-2002. The hydrologically based low flows indicate approximately equal or smaller absolute differences than biologically based low flows. The average 1-day 3-year biologically based low flow (1B3) and 4-day 3-year biologically based low flow (4B3) are less than the average 1-day 10-year hydrologically based low flow (1Q10) and 7-day 10-year hydrologic-based low flow (7Q10) respectively, and range between 28.5 percent less and 13.6 percent greater. Seasonally, the average difference between low-flow statistics computed for the five time periods and 1930-2002 is not consistent between magnitudes of low-flow statistics, and the greatest difference is for the summer (July 1-September 30) and fall (October 1-December 31) for the same time period as the greatest difference determined in the annual analysis. The greatest average difference between 1B3 and 4B3 compared to 1Q10 and 7Q10, respectively, is in the spring (April 1-June 30), ranging between 11.6 and 102.3 percent

Materials Manufactured from 3D Printed Synthetic Biology Arrays

Science.gov (United States)

Gentry, Diana; Micks, Ashley

2013-01-01

Many complex, biologically-derived materials have extremely useful properties (think wood or silk), but are unsuitable for space-related applications due to production, manufacturing, or processing limitations. Large-scale ecosystem-based production, such as raising and harvesting trees for wood, is impractical in a self-contained habitat such as a space station or potential Mars colony. Manufacturing requirements, such as the specialized equipment needed to harvest and process cotton, add too much upmass for current launch technology. Cells in nature are already highly specialized for making complex biological materials on a micro scale. We envision combining these strengths with the recently emergent technologies of synthetic biology and 3D printing to create 3D-structured arrays of cells that are bioengineered to secrete different materials in a specified three-dimensional pattern.

Base Station Performance Model

OpenAIRE

Walsh, Barbara; Farrell, Ronan

2005-01-01

At present the testing of power amplifiers within base station transmitters is limited to testing at component level as opposed to testing at the system level. While the detection of catastrophic failure is possible, that of performance degradation is not. This paper proposes a base station model with respect to transmitter output power with the aim of introducing system level monitoring of the power amplifier behaviour within the base station. Our model reflects the expe...

Biological control component [Management of water hyacinth

International Nuclear Information System (INIS)

Harley, K.L.S.

1981-01-01

Both chemical and biological control have been used with limited success for the management of water hyacinth in Fiji. In some cases heavy application of chemicals have been successful in completely killing limited areas of water hyacinth, but have resulted in the destruction of biological agents introduced to control the water hyacinth and high contamination of natural water supplies. It is proposed that under the direction of Mr S R Singh, the Senior Research Scientist (Entomology) of the Koronivia Research Station, Suva, Fiji, a collaborative programme with Dr Harley of Australia on chemical and biological control of water hyacinth be initiated. This programme would be fundamentally short-term with the prime objective being an investigation of levels of insect population following varying levels of application of chemical sprays. By comparison with control areas, observations would be made of both chemical damage and insect damage within the limited time span of the period

Space Station fluid management logistics

Science.gov (United States)

Dominick, Sam M.

1990-01-01

Viewgraphs and discussion on space station fluid management logistics are presented. Topics covered include: fluid management logistics - issues for Space Station Freedom evolution; current fluid logistics approach; evolution of Space Station Freedom fluid resupply; launch vehicle evolution; ELV logistics system approach; logistics carrier configuration; expendable fluid/propellant carrier description; fluid carrier design concept; logistics carrier orbital operations; carrier operations at space station; summary/status of orbital fluid transfer techniques; Soviet progress tanker system; and Soviet propellant resupply system observations.

47 CFR 74.793 - Digital low power TV and TV translator station protection of broadcast stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Digital low power TV and TV translator station... DISTRIBUTIONAL SERVICES Low Power TV, TV Translator, and TV Booster Stations § 74.793 Digital low power TV and TV translator station protection of broadcast stations. (a) An application to construct a new digital low power...

Biological responses of mobile phone frequency exposure.

Science.gov (United States)

Behari, Jitendra

2010-10-01

Existence of low level electromagnetic fields in the environment has been known since antiquity and their biological implications are noted for several decades. As such dosimetry of such field parameters and their emissions from various sources of mass utilization has been a subject of constant concern. Recent advancement in mobile communications has also drawn attention to their biological effects. Hand held children and adults alike generally use mobile sources as cordless phones in various positions with respect to the body. Further, an increasing number of mobile communication base stations have led to wide ranging concern about possible health effects of radiofrequency emissions. There are two distinct possibilities by which health could be affected as a result of radio frequency field exposure. These are thermal effects caused by holding mobile phones close to the body and extended conversations over a long period of time. Secondly, there could be possibly non thermal effects from both phones and base stations whereby the affects could also be cumulative. Some people may be adversely affected by the environmental impact of mobile phone base stations situated near their homes, schools or any other place. In addition to mobile phones, appliances like microwave oven etc are also in increasing use. Apart from the controversy over the possible health effects due to the non-thermal effect of electromagnetic fields the electromagnetic interaction of portable radio waves with human head needs to be quantitatively evaluated. Relating to this is the criteria of safe exposure to the population at large. While a lot of efforts have gone into resolving the issue, a clear picture has yet to emerge. Recent advances and the problems relating to the safety criteria are discussed.

Big Game Reporting Stations

Data.gov (United States)

Vermont Center for Geographic Information — Point locations of big game reporting stations. Big game reporting stations are places where hunters can legally report harvested deer, bear, or turkey. These are...

Weigh-in-Motion Stations

Data.gov (United States)

Department of Homeland Security — The data included in the GIS Traffic Stations Version database have been assimilated from station description files provided by FHWA for Weigh-in-Motion (WIM), and...

Air and radiation monitoring stations

CERN Multimedia

AUTHOR|(SzGeCERN)582709

2015-01-01

CERN has around 100 monitoring stations on and around its sites. New radiation measuring stations, capable of detecting even lower levels of radiation, were installed in 2014. Two members of HE-SEE group (Safety Engineering and Environment group) in front of one of the new monitoring stations.

47 CFR 73.1120 - Station location.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Station location. 73.1120 Section 73.1120... Rules Applicable to All Broadcast Stations § 73.1120 Station location. Each AM, FM, TV and Class A TV... be the geographical station location. [65 FR 30003, May 10, 2000] ...

Water Level Station History

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Images contain station history information for 175 stations in the National Water Level Observation Network (NWLON). The NWLON is a network of long-term,...

Biologically Inspired Intercellular Slot Synchronization

Directory of Open Access Journals (Sweden)

Alexander Tyrrell

2009-01-01

Full Text Available The present article develops a decentralized interbase station slot synchronization algorithm suitable for cellular mobile communication systems. The proposed cellular firefly synchronization (CelFSync algorithm is derived from the theory of pulse-coupled oscillators, common to describe synchronization phenomena in biological systems, such as the spontaneous synchronization of fireflies. In order to maintain synchronization among base stations (BSs, even when there is no direct link between adjacent BSs, some selected user terminals (UTs participate in the network synchronization process. Synchronization emerges by exchanging two distinct synchronization words, one transmitted by BSs and the other by active UTs, without any a priori assumption on the initial timing misalignments of BSs and UTs. In large-scale networks with inter-BS site distances up to a few kilometers, propagation delays severely affect the attainable timing accuracy of CelFSync. We show that by an appropriate combination of CelFSync with the timing advance procedure, which aligns uplink transmission of UTs to arrive simultaneously at the BS, a timing accuracy within a fraction of the inter-BS propagation delay is retained.

Local society and nuclear power stations

International Nuclear Information System (INIS)

1984-02-01

This report was made by the expert committee on region investigation, Japan Atomic Industrial Forum Inc., in fiscal years 1981 and 1982 in order to grasp the social economic influence exerted on regions by the location of nuclear power stations and the actual state of the change due to it, and to search for the way the promotion of local community should be. The influence and the effect were measured in the regions around the Fukushima No. 1 Nuclear Power Station of Tokyo Electric Power Co., Inc., the Mihama Power Station of Kansai Electric Power Co., Inc., and the Genkai Nuclear Power Station of Kyushu Electric Power Co., Inc. The fundamental recognition in this discussion, the policy of locating nuclear power stations and the management of regions, the viewpoint and way of thinking in the investigation of the regions where nuclear power stations are located, the actual state of social economic impact due to the location of nuclear power stations, the connected mechanism accompanying the location of nuclear power stations, and the location of nuclear power stations and the acceleration of planning for regional promotion are reported. In order to economically generate electric power, the rationalization in the location of nuclear power stations is necessary, and the concrete concept of building up local community must be decided. (Kako, I.)

SPRINT RA 230: Methodology for knowledge based developments

International Nuclear Information System (INIS)

Wallsgrove, R.; Munro, F.

1991-01-01

SPRINT RA 230: A Methodology for Knowledge Based Developments, funded by the European Commission, was set up to investigate the use of KBS in the engineering industry. Its aim was to find out low KBS were currently used and what people's conceptions of them was, to disseminate current knowledge and to recommend further research into this area. A survey (by post and face to face interviews) was carried out under SPRINT RA 230 to investigate requirements for more intelligent software. In the survey we looked both at how people think about Knowledge Based Systems (KBS), what they find useful and what is not useful, and what current expertise problems or limitations of conventional software might suggest KBS solutions. (orig./DG)

47 CFR 25.137 - Application requirements for earth stations operating with non-U.S. licensed space stations.

Science.gov (United States)

2010-10-01

... space stations. (a) Earth station applicants or entities filing a “letter of intent” or “Petition for... Union. (d) Earth station applicants requesting authority to operate with a non-U.S.-licensed space... 47 Telecommunication 2 2010-10-01 2010-10-01 false Application requirements for earth stations...

Radiation safety of handheld mobile phones and base stations

International Nuclear Information System (INIS)

Jokela, K.; Leszczynski, D.; Paile, W.; Salomaa, S.; Puranen, L.; Hyysalo, P.

1999-01-01

The recent expansion of personal telecommunications has led to a rapid increase in the exposure of people to the radio-frequency (RF) radiation. Although the mobile phones are low power devices, the antenna is so close to the head that the local exposure may slightly exceed 2 W/kg, the current exposure limit for the local specific absorption rate SAR for the general public. The increase in the temperature is, however, too small to have any physiological significance. On the basis of experiments with cell cultures it is possible that other biological effects caused by some unknown non-thermal mechanism exist, but thus far there is no conclusive biological or epidemiological evidence to suggest any diseases or adverse physiological changes below the thermal threshold. The use of a mobile phone by a person wearing a pace-maker, is not recommended, if the immunity of the pace-maker has not been assured. The exposure caused by the base stations is in all practical cases well below the power density limits for general public. (author)

Radiation safety of handheld mobile phones and base stations

Energy Technology Data Exchange (ETDEWEB)

Jokela, K.; Leszczynski, D.; Paile, W.; Salomaa, S.; Puranen, L.; Hyysalo, P

1999-01-01

The recent expansion of personal telecommunications has led to a rapid increase in the exposure of people to the radio-frequency (RF) radiation. Although the mobile phones are low power devices, the antenna is so close to the head that the local exposure may slightly exceed 2 W/kg, the current exposure limit for the local specific absorption rate SAR for the general public. The increase in the temperature is, however, too small to have any physiological significance. On the basis of experiments with cell cultures it is possible that other biological effects caused by some unknown non-thermal mechanism exist, but thus far there is no conclusive biological or epidemiological evidence to suggest any diseases or adverse physiological changes below the thermal threshold. The use of a mobile phone by a person wearing a pace-maker, is not recommended, if the immunity of the pace-maker has not been assured. The exposure caused by the base stations is in all practical cases well below the power density limits for general public. (author) 118 refs.

Establishment of Karadeniz Technical University Permanent GNSS Station as Reactivated of TRAB IGS Station

Directory of Open Access Journals (Sweden)

Kazancı Selma Zengin

2017-12-01

Full Text Available In recent years, Global Navigation Satellite Systems (GNSS have gained great importance in terms of the benefi ts it provides such as precise geodetic point positioning, determining crustal deformations, navigation, vehicle monitoring systems and meteorological applications etc. As in Turkey, for this purpose, each country has set up its own GNSS station networks like Turkish National Permanent RTK Network analyzed precise station coordinates and velocities together with the International GNSS Service, Turkish National Fundamental GPS Network and Turkish National Permanent GNSS Network (TNPGN stations not only are utilized as precise positioning but also GNSS meteorology studies so total number of stations are increased. This work is related to the reactivated of the TRAB IGS station which was established in Karadeniz Technical University, Department of Geomatics Engineering. Within the COST ES1206 Action (GNSS4SWEC KTU analysis center was established and Trop-NET system developed by Geodetic Observatory Pecny (GOP, RIGTC in order to troposphere monitoring. The project titled “Using Regional GNSS Networks to Strengthen Severe Weather Prediction” was accepted to the scientifi c and technological research council of Turkey (TUBITAK. With this project, we will design 2 new constructed GNSS reference station network. Using observation data of network, we will compare water vapor distribution derived by GNSS Meteorology and GNSS Tomography. At this time, KTU AC was accepted as E-GVAP Analysis Centre in December 2016. KTU reference station is aimed to be a member of the EUREF network with these studies.

Establishment of Karadeniz Technical University Permanent GNSS Station as Reactivated of TRAB IGS Station

Science.gov (United States)

Kazancı, Selma Zengin; Kayıkçı, Emine Tanır

2017-12-01

In recent years, Global Navigation Satellite Systems (GNSS) have gained great importance in terms of the benefi ts it provides such as precise geodetic point positioning, determining crustal deformations, navigation, vehicle monitoring systems and meteorological applications etc. As in Turkey, for this purpose, each country has set up its own GNSS station networks like Turkish National Permanent RTK Network analyzed precise station coordinates and velocities together with the International GNSS Service, Turkish National Fundamental GPS Network and Turkish National Permanent GNSS Network (TNPGN) stations not only are utilized as precise positioning but also GNSS meteorology studies so total number of stations are increased. This work is related to the reactivated of the TRAB IGS station which was established in Karadeniz Technical University, Department of Geomatics Engineering. Within the COST ES1206 Action (GNSS4SWEC) KTU analysis center was established and Trop-NET system developed by Geodetic Observatory Pecny (GOP, RIGTC) in order to troposphere monitoring. The project titled "Using Regional GNSS Networks to Strengthen Severe Weather Prediction" was accepted to the scientifi c and technological research council of Turkey (TUBITAK). With this project, we will design 2 new constructed GNSS reference station network. Using observation data of network, we will compare water vapor distribution derived by GNSS Meteorology and GNSS Tomography. At this time, KTU AC was accepted as E-GVAP Analysis Centre in December 2016. KTU reference station is aimed to be a member of the EUREF network with these studies.

Advances in power station construction

International Nuclear Information System (INIS)

Anon.

1986-01-01

This book is about power stations - specifically about the construction of modern power stations by the Central Electricity Generating Board in England and Wales over the past decade. It describes the work of the CEGB's Generation Development and Construction Division, perhaps better known throughout the world as simply 'Barnwood' where it has its Headquarters in Gloucester, UK. Barnwood was formed in the early 1970s to concentrate the CEGB's then dispersed engineering construction resources to cope with the smaller number but greatly increased size and complexity of modern power station projects. Perhaps uniquely over the ten years since its formation Barnwood has managed the construction of all types of station; coal-fired, oil-fired, nuclear, pumped storage and hydro. This book tells the story of these various projects and gives detailed descriptions of the respective stations. However, it is not intended as a comprehensive description of power station technology. Rather it is intended to convey the scale of such projects and the many decisions and compromises which have to be made in the course of managing their construction

The Princess Elisabeth Station

Science.gov (United States)

Berte, Johan

2012-01-01

Aware of the increasing impact of human activities on the Earth system, Belgian Science Policy Office (Belspo) launched in 1997 a research programme in support of a sustainable development policy. This umbrella programme included the Belgian Scientific Programme on Antarctic Research. The International Polar Foundation, an organization led by the civil engineer and explorer Alain Hubert, was commissioned by the Belgian Federal government in 2004 to design, construct and operate a new Belgian Antarctic Research Station as an element under this umbrella programme. The station was to be designed as a central location for investigating the characteristic sequence of Antarctic geographical regions (polynia, coast, ice shelf, ice sheet, marginal mountain area and dry valleys, inland plateau) within a radius of 200 kilometers (approx.124 miles) of a selected site. The station was also to be designed as "state of the art" with respect to sustainable development, energy consumption, and waste disposal, with a minimum lifetime of 25 years. The goal of the project was to build a station and enable science. So first we needed some basic requirements, which I have listed here; plus we had to finance the station ourselves. Our most important requirement was that we decided to make it a zero emissions station. This was both a philosophical choice as we thought it more consistent with Antarctic Treaty obligations and it was also a logistical advantage. If you are using renewable energy sources, you do not have to bring in all the fuel.

UK 2009-2010 repeat station report

Directory of Open Access Journals (Sweden)

Thomas J.G. Shanahan

2013-03-01

Full Text Available The British Geological Survey is responsible for conducting the UK geomagnetic repeat station programme. Measurements made at the UK repeat station sites are used in conjunction with the three UK magnetic observatories: Hartland, Eskdalemuir and Lerwick, to produce a regional model of the local field each year. The UK network of repeat stations comprises 41 stations which are occupied at approximately 3-4 year intervals. Practices for conducting repeat station measurements continue to evolve as advances are made in survey instrumentation and as the usage of the data continues to change. Here, a summary of the 2009 and 2010 UK repeat station surveys is presented, highlighting the measurement process and techniques, density of network, reduction process and recent results.

Swedish nuclear waste efforts

International Nuclear Information System (INIS)

Rydberg, J.

1981-09-01

After the introduction of a law prohibiting the start-up of any new nuclear power plant until the utility had shown that the waste produced by the plant could be taken care of in an absolutely safe way, the Swedish nuclear utilities in December 1976 embarked on the Nuclear Fuel Safety Project, which in November 1977 presented a first report, Handling of Spent Nuclear Fuel and Final Storage of Vitrified Waste (KBS-I), and in November 1978 a second report, Handling and Final Storage of Unreprocessed Spent Nuclear Fuel (KBS II). These summary reports were supported by 120 technical reports prepared by 450 experts. The project engaged 70 private and governmental institutions at a total cost of US $15 million. The KBS-I and KBS-II reports are summarized in this document, as are also continued waste research efforts carried out by KBS, SKBF, PRAV, ASEA and other Swedish organizations. The KBS reports describe all steps (except reprocessing) in handling chain from removal from a reactor of spent fuel elements until their radioactive waste products are finally disposed of, in canisters, in an underground granite depository. The KBS concept relies on engineered multibarrier systems in combination with final storage in thoroughly investigated stable geologic formations. This report also briefly describes other activities carried out by the nuclear industry, namely, the construction of a central storage facility for spent fuel elements (to be in operation by 1985), a repository for reactor waste (to be in operation by 1988), and an intermediate storage facility for vitrified high-level waste (to be in operation by 1990). The R and D activities are updated to September 1981

Studies on urine treatment by biological purification using Azolla and UV photocatalytic oxidation

Science.gov (United States)

Liu, Xiaofeng; Chen, Min; Bian, Zuliang; Liu, Chung-Chu

The amount of water consumed in space station operations is very large. In order to reduce the amount of water which must be resupplied from Earth, the space station needs to resolve the problems of water supply. For this reason, the recovery, regeneration and utilization of urine of astronauts are of key importance. Many investigations on this subject have been reported. Our research is based on biological absorption and, purification using UV photocatalytic oxidation techniques to achieve comprehensive treatment for urine. In the treatment apparatus we created, the urine solution is used as part of the nutrient solution for the biological components in our bioregenerative life support system. After being absorbed, the nutrients from the urine were then decomposed, metabolized and purified which creates a favorable condition for the follow-up oxidation treatment by UV photocatalytic oxidation. After these two processes, the treated urine solution reached Chinese national standards for drinking water quality (GB5749-1985).

European activities in space radiation biology and exobiology

International Nuclear Information System (INIS)

Horneck, G.

1996-01-01

In view of the space station era, the European Space Agency has initiated a review and planning document for space life sciences. Radiation biology includes dosimetry of the radiation field and its modification by mass shielding, studies on the biological responses to radiation in space, on the potential impact of space flight environment on radiation effects, and assessing the radiation risks and establishing radiation protection guidelines. To reach a better understanding of the processes leading to the origin, evolution and distribution of life, exobiological activities include the exploration of the solar system, the collection and analysis of extraterrestrial samples and the utilization of space as a tool for testing the impact of space environment on organics and resistant life forms. (author)

[Hygiene and security management in medical biology laboratory].

Science.gov (United States)

Vinner, E; Odou, M F; Fovet, B; Ghnassia, J C

2013-06-01

Risk management in Medical Biology Laboratory (MBL) which includes hygiene and waste management, is an integrated process to the whole MBL organisation. It is composed of three stages: risks factors identification, grading and prioritization, and their evaluation in the system. From the legislation and NF EN ISO 15189 standard's requirements viewpoint, prevention and protection actions to implement are described, at premises level, but also at work station environment's one (human resources and equipments) towards biological, chemical, linked to gas, to ionizing or non ionizing radiations and fire riks, in order not to compromise patients safety, employees safety, and quality results. Then, although NF EN 15189 standard only enacts requirements in terms of prevention, curative actions after established blood or chemical exposure accident are defined.

Thermal management of space stations

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

Thermal management aims at making full use of energy resources available in the space station to reduce energy consumption, waste heat rejection and the weight of the station. It is an extension of the thermal control. This discussion introduces the concept and development of thermal management, presents the aspects of thermal management and further extends its application to subsystems of the space station.

Beaver Valley Power Station and Shippingport Atomic Power Station. 1984 Annual environmental report, radiological. Volume 2

International Nuclear Information System (INIS)

1985-01-01

This report describes the Radiological Environmental Monitoring Program conducted during 1984 in the vicinity of the Beaver Valley Power Station and the Shippingport Atomic Power Station. The Radiological Environmental Program consists of on-site sampling of water and gaseous effluents and off-site monitoring of water, air, river sediments, soils, food pathway samples, and radiation levels in the vicinity of the site. This report discusses the results of this monitoring during 1984. The environmental program outlined in the Beaver Valley Power Station Technical Specifications was followed throughout 1984. The results of this environmental monitoring program show that Shippingport Atomic Power Station and Beaver Valley Power Station operations have not adversely affected the surrounding environment. 23 figs., 18 tabs

Arduino adventures escape from Gemini station

CERN Document Server

Kelly, James Floyd

2013-01-01

Arduino Adventures: Escape from Gemini Station provides a fun introduction to the Arduino microcontroller by putting you (the reader) into the action of a science fiction adventure story.  You'll find yourself following along as Cade and Elle explore Gemini Station-an orbiting museum dedicated to preserving and sharing technology throughout the centuries. Trouble ensues. The station is evacuated, including Cade and Elle's class that was visiting the station on a field trip. Cade and Elle don't make it aboard their shuttle and are trapped on the station along with a friendly artificial intellig

Hydrogen vehicle fueling station

Energy Technology Data Exchange (ETDEWEB)

Daney, D.E.; Edeskuty, F.J.; Daugherty, M.A. [Los Alamos National Lab., NM (United States)] [and others

1995-09-01

Hydrogen fueling stations are an essential element in the practical application of hydrogen as a vehicle fuel, and a number of issues such as safety, efficiency, design, and operating procedures can only be accurately addressed by a practical demonstration. Regardless of whether the vehicle is powered by an internal combustion engine or fuel cell, or whether the vehicle has a liquid or gaseous fuel tank, the fueling station is a critical technology which is the link between the local storage facility and the vehicle. Because most merchant hydrogen delivered in the US today (and in the near future) is in liquid form due to the overall economics of production and delivery, we believe a practical refueling station should be designed to receive liquid. Systems studies confirm this assumption for stations fueling up to about 300 vehicles. Our fueling station, aimed at refueling fleet vehicles, will receive hydrogen as a liquid and dispense it as either liquid, high pressure gas, or low pressure gas. Thus, it can refuel any of the three types of tanks proposed for hydrogen-powered vehicles -- liquid, gaseous, or hydride. The paper discusses the fueling station design. Results of a numerical model of liquid hydrogen vehicle tank filling, with emphasis on no vent filling, are presented to illustrate the usefulness of the model as a design tool. Results of our vehicle performance model illustrate our thesis that it is too early to judge what the preferred method of on-board vehicle fuel storage will be in practice -- thus our decision to accommodate all three methods.

Application for the Tape Station

CERN Document Server

Solero, A

2003-01-01

The Tape Station is used as an Isolde facility to observe the variations of intensity and the lifespan of certain isotopes. A Siemens Simatic FM-352-5 module controls the Tape Station in a PLC system then a DSC controls the PLC, which will be controlled the Tape station program. During the Isolde consolidation project, the Tape Station has been rebuilt, and the control system has been fully integrated in the PS control. Finally, a new application has been written in JAVA Development kit 1.4 and the PS Java environment. The main purpose of this note is to explain how to use this program.

Beaver Valley Power Station and Shippingport Atomic Power Station. 1977 annual environmental report: radiological. Volume 2

International Nuclear Information System (INIS)

1978-01-01

The environmental monitoring conducted during 1977 in the vicinity of the Beaver Valley Power Station and the Shippingport Atomic Power Station is described. The environmental monitoring program consists of onsite sampling of water, gaseous, and air effluents, as well as offsite monitoring of water, air, river sediments, and radiation levels in the vicinity of the site. The report discusses releases of small quantities of radioactivity to the Ohio River from the Beaver Valley Power Station and Shippingport Atomic Power Station during 1977

Work/control stations in Space Station weightlessness

Science.gov (United States)

Willits, Charles

1990-01-01

An ergonomic integration of controls, displays, and associated interfaces with an operator, whose body geometry and dynamics may be altered by the state of weightlessness, is noted to rank in importance with the optimal positioning of controls relative to the layout and architecture of 'body-ported' work/control stations applicable to the NASA Space Station Freedom. A long-term solution to this complex design problem is envisioned to encompass the following features: multiple imaging, virtual optics, screen displays controlled by a keyboard ergonomically designed for weightlessness, cursor control, a CCTV camera, and a hand-controller featuring 'no-grip' vernier/tactile positioning. This controller frees all fingers for multiple-switch actuations, while retaining index/register determination with the hand controller. A single architectural point attachment/restraint may be used which requires no residual muscle tension in either brief or prolonged operation.

Hydrogen Fuelling Stations

DEFF Research Database (Denmark)

Rothuizen, Erasmus Damgaard

. A system consisting of one high pressure storage tank is used to investigate the thermodynamics of fuelling a hydrogen vehicle. The results show that the decisive parameter for how the fuelling proceeds is the pressure loss in the vehicle. The single tank fuelling system is compared to a cascade fuelling......This thesis concerns hydrogen fuelling stations from an overall system perspective. The study investigates thermodynamics and energy consumption of hydrogen fuelling stations for fuelling vehicles for personal transportation. For the study a library concerning the components in a hydrogen fuelling...... station has been developed in Dymola. The models include the fuelling protocol (J2601) for hydrogen vehicles made by Society of Automotive Engineers (SAE) and the thermodynamic property library CoolProp is used for retrieving state point. The components in the hydrogen fuelling library are building up...

Tobruk power station

Energy Technology Data Exchange (ETDEWEB)

Boergardts, B

1978-01-01

In February of 1975, the Electricity Corporation Benghazi (ECB) awarded a contract for the construction of a turnkey power station and seawater desalination plant in Tobruk, Libya to a consortium under the leadership of BBC Mannheim. This power station has an output of 129 MW and supplies about 24,000 m/sup 3/ of drinking water daily. It went into operation in 1977, two and a half years after the contract was awarded.

National Seismic Station

International Nuclear Information System (INIS)

Stokes, P.A.

1982-06-01

The National Seismic Station was developed to meet the needs of regional or worldwide seismic monitoring of underground nuclear explosions to verify compliance with a nuclear test ban treaty. The Station acquires broadband seismic data and transmits it via satellite to a data center. It is capable of unattended operation for periods of at least a year, and will detect any tampering that could result in the transmission of unauthentic seismic data

Shippingport Station Decommissioning Project

International Nuclear Information System (INIS)

McKernan, M.L.

1989-01-01

The Shippingport Atomic Power Station was located on the Ohio River in Shippingport Borough (Beaver County), Pennsylvania, USA. The US Atomic Energy Commission (AEC) constructed the plant in the mid-1950s on a seven and half acre parcel of land leased from Duquesne Light Company (DLC). The purposes were to demonstrate and to develop Pressurized Water Recovery technology and to generate electricity. DLC operated the Shippingport plant under supervision of (the successor to AEC) the Department of Energy (DOE)-Naval Reactors (NR) until operations were terminated on October 1, 1982. NR concluded end-of-life testing and defueling in 1984 and transferred the Station's responsibility to DOE Richland Operations Office (RL), Surplus Facility Management Program Office (SFMPO5) on September 5, 1984. SFMPO subsequently established the Shippingport Station Decommissioning Project and selected General Electric (GE) as the Decommissioning Operations Contractor. This report is intended to provide an overview of the Shippingport Station Decommissioning Project

A research on the environmental impact on nearby waters range at low-level radioactive waste water drain from the Dayawan nuclear power station

International Nuclear Information System (INIS)

Zhang Chunling; Xu Zitu; Xiao Zhang.

1987-01-01

The possible influence of the low-level radioactive waste water drain from the Dayawan nuclear power station upon nearby waters range is discussed. The contents of the article contains the numerical simulation on tidal currents and pollutant diffusion, the calculation of concentration distribution of radioactive contaminants in the water area and of polluted field, and the criterion on radioactive contaminant influence on nearby residents and aquatic biologicals. The result shows that when the Dayawan nuclear power station is on normal operation and after the low-level radioactive waste water has been drained off into the sea, the radioactive concentration is even lower than the natural background radiation just out-side the area of about 4 km 2 round the water outlet. As a result, it won't cause any danger to the water environment. Due to the fact that the concentration of the low-level radioactive waste water from the nuclear power station fully accords with the national standard GB4792-84 and the sea water quality sandard GBH2, 3-82. It is no harm to either residents and aquatic biologicals or ecological balance

20 years of power station master training

International Nuclear Information System (INIS)

Schwarz, O.

1977-01-01

In the early fifties, the VGB working group 'Power station master training' elaborated plans for systematic and uniform training of power station operating personnel. In 1957, the first power station master course was held. In the meantime, 1.720 power station masters are in possession of a master's certificate of a chamber of commerce and trade. Furthermore, 53 power station masters have recently obtained in courses of the 'Kraftwerksschule e.V.' the know-how which enables them to also carry out their duty as a master in nuclear power stations. (orig.) [de

A report on upgraded seismic monitoring stations in Myanmar: Station performance and site response

Science.gov (United States)

Thiam, Hrin Nei; Min Htwe, Yin Myo; Kyaw, Tun Lin; Tun, Pa Pa; Min, Zaw; Htwe, Sun Hninn; Aung, Tin Myo; Lin, Kyaw Kyaw; Aung, Myat Min; De Cristofaro, Jason; Franke, Mathias; Radman, Stefan; Lepiten, Elouie; Wolin, Emily; Hough, Susan E.

2017-01-01

Myanmar is in a tectonically complex region between the eastern edge of the Himalayan collision zone and the northern end of the Sunda megathrust. Until recently, earthquake monitoring and research efforts have been hampered by a lack of modern instrumentation and communication infrastructure. In January 2016, a major upgrade of the Myanmar National Seismic Network (MNSN; network code MM) was undertaken to improve earthquake monitoring capability. We installed five permanent broadband and strong‐motion seismic stations and real‐time data telemetry using newly improved cellular networks. Data are telemetered to the MNSN hub in Nay Pyi Taw and archived at the Incorporated Research Institutions for Seismology Data Management Center. We analyzed station noise characteristics and site response using noise and events recorded over the first six months of station operation. Background noise characteristics vary across the array, but indicate that the new stations are performing well. MM stations recorded more than 20 earthquakes of M≥4.5 within Myanmar and its immediate surroundings, including an M 6.8 earthquake located northwest of Mandalay on 13 April 2016 and the Mw 6.8 Chauk event on 24 August 2016. We use this new dataset to calculate horizontal‐to‐vertical spectral ratios, which provide a preliminary characterization of site response of the upgraded MM stations.

Review of Cytogenetic analysis of restoration workers for Fukushima Daiichi nuclear power station accident

International Nuclear Information System (INIS)

Suto, Yumiko

2016-01-01

Japan faced with the nuclear accident of the Fukushima Daiichi Nuclear Power Station (NPS) caused by the combined disaster of the Great East Japan Earthquake and the subsequent tsunamis on 11 March 2011. National Institute of Radiological Sciences received all nuclear workers who were engaged in emergency response tasks at the NPS and suspected of being overexposed to acute radiation. Biological dosimetry by dicentric chromosome assay was helpful for medical triage and management of the workers. When an unplanned radiation exposure occurs, biological dosimetry based on cytogenetic assays has been used to estimate the absorbed dose in the exposed individual to get useful information for the medical management of radiological casualties with suspected acute radiation syndrome (ARS). Nowadays, more cytogenetic assays to measure chromosomal aberrations, such as micronuclei in bi-nucleated cells, prematurely condensed chromosomes (PCCs) and inter-chromosomal exchanges detected by fluorescence in situ hybridization (FISH) techniques, are available. However, the dicentric chromosome assay (DCA) using peripheral blood lymphocytes is still considered to be the 'gold standard' of biological dosimetry for the radiation emergency medicine. Experimental protocols of DCA has been standardized and shared among laboratories all over the world. In fact, DCA was useful in previous radiation accidents, e.g. the Chernobyl accident in 1986, the Goiania accident in 1987, the JCO criticality accident in 1999 and the Tokyo electric power company (TEPCO) Fukushima Daiichi Nuclear Power Station (NPS) accident in 2011. The recent development of microscopic image analysis system with automatic metaphase finding and capturing functions was helpful for rapid detection of dicentric chromosomes to perform DCA for the Fukushima NPS restoration workers. (author)

Phenomenological description reference concept (Spent Fuel - Copper - Iron - Bentonite - Granite)

International Nuclear Information System (INIS)

Lehikoinen, J.; Nordman, H.

2008-12-01

This report gives a broad overview of the salient processes and associated time frames and uncertainties pertaining to the long-term normal evolution of the near-field of a deep repository of the KBS-3V type. By normal evolution, reference is made to the description of the evolution of a disposal system subject to the assumption that all the spent fuel canisters remain intact following emplacement and repository closure for at least the design corrosion lifetime of the canister overpack in the expected repository conditions. In this connection, the effects of future glaciations, canister manufacturing defects and small-scale tectonic activity are briefly touched upon. The roles of the different repository near-field barriers in providing safety are briefly noted. The description of the normal evolution of a KBS-3V-type repository near-field conditions external to the unbreached spent fuel canister has been realized in terms of processes rather than timescales. Separate chapters have been devoted to the thermal, hydraulic, mechanical and chemical/biological evolution of the repository system, with due attention to some of the couplings between them. (orig.)

Determination of production biology of cladocera in a reservoir receiving hyperthermal effluents from a nuclear production reactor

International Nuclear Information System (INIS)

Vigerstad, T.J.

1980-01-01

The effects on zooplankton of residence in a cooling reservoir receiving hyperthermal effluents directly from a nuclear-production-reactor were studied. Rates of cladoceran population production were compared at two stations in the winter and summer of 1976 on Par Pond located on the Savannah River Plant, Aiken, SC. One station was located in an area of the reservoir directly receiving hyperthermal effluent (Station MAS) and the second was located about 4 km away in an area where surface temperatures were normal for reservoirs in the general geographical region (Station CAS). A non-parametric comparison between stations of standing stock and fecundity data for Bosmina longirostris, taken for the egg ratio model, was used to observe potential hyperthermal effluent effects. There was a statistically higher incidence of deformed eggs in the Bosmina population at Station MAS in the summer. Bosmina standing stock underwent two large oscillations in the winter and three large oscillations in the summer at Station MAS compared with two in the winter and one in the summer at Station CAS. These results are consistent with almost all other Par Pond studies which have found the two stations to be essentially similar in spectra composition but with some statistically significant differences in various aspects of the biology of the species

GETOUT - a one-dimensional model for groundwater transport of radionuclide decay chains

International Nuclear Information System (INIS)

Grundfelt, B.; Elert, M.

1980-01-01

The GETOUT-code, originally developed at Batelle Pacific Northwest Laboratories (PNL), was used in the KBS-project to calculate the radionuclide discharges from the repository. The version used in KBS was a translation of the PNL BASIC-language version as by December 1976. In this report a new version, mathematically compatible with the PNL FORTRAN version as by 1979-08-15, is documented. Details are given on the differences between this new version and the version used in the KBS project up to now. (author)

Influence of Great East Japan Earthquake on neutron source station in J-PARC

International Nuclear Information System (INIS)

Sakai, Kenji; Sakamoto, Shinichi; Kinoshita, Hidetaka; Seki, Masakazu; Haga, Katsuhiro; Kogawa, Hiroyuki; Wakui, Takashi; Naoe, Takashi; Kasugai, Yoshimi; Tatsumoto, Hideki; Aso, Tomokazu; Hasegawa, Shoichi; Maekawa, Fujio; Oikawa, Kenichi; Ooi, Motoki; Watanabe, Akihiko; Teshigawara, Makoto; Meigo, Shin-ichiro; Ikezaki, Kiyomi; Akutsu, Atsushi; Harada, Masahide; Takada, Hiroshi; Futakawa, Masatoshi

2012-03-01

This report investigates the behavior, damage and restoration of each component in a neutron source station of the Materials and Life Science Experimental Facility (MLF) of J-PARC at the time of the Great East Japan Earthquake (M9.0) and verified the safety design for emergency accidents in the neutron source station. The neutron source station of the MLF at the J-PARC generates neutrons by injecting proton beams into a mercury target, and supplies to user experimental apparatuses. It consists of the mercury target, three moderators filled with supercritical hydrogen, reflectors, water cooling shields, a vessel filled with helium gas, neutron beam shutters, biological-shields and so on. In case of loss of their external electric power supply, a control function for the source station is kept by an emergency power supply. According to interlock sequences in an emergency, a signal for terminating the beam operation is transmitted, the circulators shut down automatically, and the hydrogen gas is released out of the building. On March 11 in 2011, strong shocks caused by the earthquake were observed all over Ibaraki prefecture. At the date, a status of the source station was ready for the restart of beam operation. In the MLF, after strong quakes were detected at the several instruments, the external power supply was lost, all of the circulators shut down automatically, and the hydrogen gas was released. The leakages of mercury, hydrogen and radio-activation gases did not occur. While, the quakes made gaps between the shield blocks and ruptured external pipe lines for compressed air and water by subsidence around the building. But significant damages to the components were not found though the pressure drop of compressed air lines influenced on the mercury target trolley lock system and pneumatic operation values. These results substantiated the validity of the safety design for emergency accidents in the neutron source station in the MLF, and suggested several points

47 CFR 22.313 - Station identification.

Science.gov (United States)

2010-10-01

... Telephone Radio Systems in the Rural Radiotelephone Service; (5) [Reserved] (6) Stations operating pursuant... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES PUBLIC MOBILE SERVICES... of each station in the Public Mobile Services must ensure that the transmissions of that station are...

Evaluating the feasibility of biological waste processing for long term space missions

Science.gov (United States)

Garland, J. L.; Alazraki, M. P.; Atkinson, C. F.; Finger, B. W.; Sager, J. C. (Principal Investigator)

1998-01-01

Recycling waste products during orbital (e.g., International Space Station) and planetary missions (e.g., lunar base, Mars transit mission, Martian base) will reduce storage and resupply costs. Wastes streams on the space station will include human hygiene water, urine, faeces, and trash. Longer term missions will contain human waste and inedible plant material from plant growth systems used for atmospheric regeneration, food production, and water recycling. The feasibility of biological and physical-chemical waste recycling is being investigated as part of National Aeronautics and Space Administration's (NASA) Advanced Life Support (ALS) Program. In-vessel composting has lower manpower requirements, lower water and volume requirements, and greater potential for sanitization of human waste compared to alternative bioreactor designs such as continuously stirred tank reactors (CSTR). Residual solids from the process (i.e. compost) could be used a biological air filter, a plant nutrient source, and a carbon sink. Potential in-vessel composting designs for both near- and long-term space missions are presented and discussed with respect to the unique aspects of space-based systems.

Space station operations management

Science.gov (United States)

Cannon, Kathleen V.

1989-01-01

Space Station Freedom operations management concepts must be responsive to the unique challenges presented by the permanently manned international laboratory. Space Station Freedom will be assembled over a three year period where the operational environment will change as significant capability plateaus are reached. First Element Launch, Man-Tended Capability, and Permanent Manned Capability, represent milestones in operational capability that is increasing toward mature operations capability. Operations management concepts are being developed to accomodate the varying operational capabilities during assembly, as well as the mature operational environment. This paper describes operations management concepts designed to accomodate the uniqueness of Space Station Freedoom, utilizing tools and processes that seek to control operations costs.

Modelling of near-field radionuclide transport phenomena in a KBS-3V type of repository for nuclear waste with Goldsim Code - and verification against previous methods

International Nuclear Information System (INIS)

Pulkkanen, V.-M.; Nordman, H.

2010-03-01

Traditional radionuclide transport models overestimate significantly some phenomena, or completely ignore them. This motivates the development of new more precise models. As a result, this work is a description of commissioning of a new KBS-3V near-field radionuclide transport model, which has been done with a commercial software called GoldSim. According to earlier models, GoldSim model uses rz coordinates, but the solubilities of radionuclides have been treated more precisely. To begin with, the physical phenomena concerning near-field transport have been introduced according to GoldSim way of thinking. Also, the computational methods of GoldSim have been introduced and compared to methods used earlier. The actual verification of GoldSim model has been carried out by comparing the GoldSim results from simple cases to the corresponding results obtained with REPCOM, a software developed by VTT and used in several safety assessments. The results agree well. Finally, a few complicated cases were studied. In these cases, the REPCOM's limitations in handling of some phenomena become evident. The differences in the results are caused especially by the extension of the solubility limit to the whole computational domain, and the element-wise treatment of the solubilities which was used instead of nuclide-wise treatment. This work has been carried out as a special assignment to the former laboratory of Advanced Energy Systems in Helsinki University of Technology. The work was done at VTT. (orig.)

Coupled thermo-hydro-mechanical calculations of the water saturation phase of a KBS-3 deposition hole. Influence of hydraulic rock properties on the water saturation phase

International Nuclear Information System (INIS)

Boergesson, Lennart; Hernelind, J.

1999-12-01

The wetting process in deposition holes designed according to the KBS-3-concept has been simulated with finite element calculations of the thermo-hydro-mechanical processes in the buffer, backfill and surrounding rock. The buffer material has been modelled according to the preliminary material models developed for swelling clay. The properties of the rock have been varied in order to investigate the influence of the rock properties and the hydraulic conditions on the wetting processes. In the modelling of the test holes the permeability of the rock matrix, the water supply from the backfill, the water pressure in the surrounding rock, the permeability of the disturbed zone around the deposition hole, the water retention properties of the rock, and the transmissivity of two fractures intersecting the deposition hole have been varied. The calculations indicate that the wetting takes about 5 years if the water pressure in the rock is high and if the permeability of the rock is so high that the properties of the bentonite determine the wetting rate. However, it may take considerably more than 30 years if the rock is very tight and the water pressure in the rock is low. The calculations also show that the influence of the rock structure is rather large except for the influence of the transmissivity T of the fractures, which turned out to be insignificant for the values used in the calculations

Low-pH concrete plug for sealing the KBS-3V deposition tunnels

International Nuclear Information System (INIS)

Malm, Richard

2012-01-01

In SKB's main alternative for final repository of radioactive material, KBS-3V, the backfilled deposition tunnels will be separated from the remaining tunnel system with concrete plugs. These concrete plugs will be designed for a life span of 100 years and their function shall maintain until the transport tunnels outside the plug are backfilled and the natural geohydrological conditions have been restored. The purpose of this report is to document the results and the evaluation from this project and motivate the choice of the most appropriate design for closing the deposition tunnels in the spent fuel repository. The purpose has also been to investigate and present the loads acting on the plug system and determine the load capacity of the concrete plug. This report is the result of a project conducted between 2009-01-01 - 2010-12-31 and the project group has made its assessment based on the conditions and requirements that are present today. The entire design of the plug system is part of this project, where the plug system consists of a filter, a bentonite seal and a cast-in-place concrete plug. Two different conceptual design alternatives for the concrete plug have been studied in this report, one long tapered plug and one dome shaped plug. The results in this report focus on the choice of the conceptual design for the concrete plug and its possibility to assist the entire plug system to satisfy its requirements. It is a complicated task to dispose the radioactive waste and it sets high technical requirements on the design and the production of the backfill and the closing of the deposition tunnels. The aim of this project is to design and develop a plug system suitable for production. This is done by the means of numerical calculations and analyses. The primary function of the concrete plug is to act as a resistance to the external loads originated from the axial expansion of the backfill and the water pressure. However, the entire plug system has a requirement

Assessment of backfill design for a KBS-3V repository: the BACLO program

International Nuclear Information System (INIS)

Jonsson, E.; Gunnarsson, D.; Hansen, J.; Keto, P.; Dixon, D.A.; Boergesson, L.

2010-01-01

Document available in extended abstract form only. Posiva and SKB initiated a joint programme BACLO (Backfilling and Closure of the Deep repository) in 2003 with the aim to develop methods and clay-based materials for backfilling the deposition tunnels of a repository utilizing the KBS-3V deposition concept. This paper summarises the work done in the third and final phase of the BACLO programme (2006-2008). The main objectives of this work were to examine backfill materials, deposition concepts and their importance to the clay-based block and pellet backfilling concept. Baclo Phase III was primarily intended to address the following four items: 1. evaluate options for design of block and pellet/granule materials for use in backfilling and in so doing provide a basis for selecting backfill materials; 2. provide a basis for recommending reference design(s) for backfilling through evaluation of materials, environmental processes and technical constraints likely to be encountered in a repository; 3. analyze how the potentially critical processes taking place during the installation and saturation phase affect the performance of the backfill and consequently the design basis for the backfill; and 4. evaluate how water will move through backfilled volumes and generally identify under what conditions water management will become an operational issue; and identify needs for further investigations and technical development. To address these objectives, studies were undertaken to examine how the various processes active during backfill installation and saturation as well as technical constraints affect its design basis. The work focused on the performance and technical feasibility of a block backfill concept, which calls for filling the majority of the tunnel volume with pre-compacted, clay-based backfill blocks and the remaining volume with bentonite pellets. Several backfill composition alternatives were chosen for study and they consisted of clay materials with differing

Low-pH concrete plug for sealing the KBS-3V deposition tunnels

Energy Technology Data Exchange (ETDEWEB)

Malm, Richard (Vattenfall Power Consultant AB (Sweden))

2012-01-15

In SKB's main alternative for final repository of radioactive material, KBS-3V, the backfilled deposition tunnels will be separated from the remaining tunnel system with concrete plugs. These concrete plugs will be designed for a life span of 100 years and their function shall maintain until the transport tunnels outside the plug are backfilled and the natural geohydrological conditions have been restored. The purpose of this report is to document the results and the evaluation from this project and motivate the choice of the most appropriate design for closing the deposition tunnels in the spent fuel repository. The purpose has also been to investigate and present the loads acting on the plug system and determine the load capacity of the concrete plug. This report is the result of a project conducted between 2009-01-01 - 2010-12-31 and the project group has made its assessment based on the conditions and requirements that are present today. The entire design of the plug system is part of this project, where the plug system consists of a filter, a bentonite seal and a cast-in-place concrete plug. Two different conceptual design alternatives for the concrete plug have been studied in this report, one long tapered plug and one dome shaped plug. The results in this report focus on the choice of the conceptual design for the concrete plug and its possibility to assist the entire plug system to satisfy its requirements. It is a complicated task to dispose the radioactive waste and it sets high technical requirements on the design and the production of the backfill and the closing of the deposition tunnels. The aim of this project is to design and develop a plug system suitable for production. This is done by the means of numerical calculations and analyses. The primary function of the concrete plug is to act as a resistance to the external loads originated from the axial expansion of the backfill and the water pressure. However, the entire plug system has a

Estimation of Biological Effects of Tritium.

Science.gov (United States)

Umata, Toshiyuki

2017-01-01

Nuclear fusion technology is expected to create new energy in the future. However, nuclear fusion requires a large amount of tritium as a fuel, leading to concern about the exposure of radiation workers to tritium beta radiation. Furthermore, countermeasures for tritium-polluted water produced in decommissioning of the reactor at Fukushima Daiichi Nuclear Power Station may potentially cause health problems in radiation workers. Although, internal exposure to tritium at a low dose/low dose rate can be assumed, biological effect of tritium exposure is not negligible, because tritiated water (HTO) intake to the body via the mouth/inhalation/skin would lead to homogeneous distribution throughout the whole body. Furthermore, organically-bound tritium (OBT) stays in the body as parts of the molecules that comprise living organisms resulting in long-term exposure, and the chemical form of tritium should be considered. To evaluate the biological effect of tritium, the effect should be compared with that of other radiation types. Many studies have examined the relative biological effectiveness (RBE) of tritium. Hence, we report the RBE, which was obtained with radiation carcinogenesis classified as a stochastic effect, and serves as a reference for cancer risk. We also introduce the outline of the tritium experiment and the principle of a recently developed animal experimental system using transgenic mouse to detect the biological influence of radiation exposure at a low dose/low dose rate.

Principles of nuclear power station control

International Nuclear Information System (INIS)

Knowles, J.B.

1975-12-01

This memorandum represents lecture notes first distributed as part of a UKAEA introductory course on Reactor Technology held during November 1975. A nuclear power station is only one element of a dispersed interconnected arrangement of other nuclear and fossil-fired units which together constitute the national 'grid'. Thus the control of any one station must relate to the objectives of the grid network as a whole. A precise control of the supply frequency of the grid is achieved by regulating the output power of individual stations, and it is necessary for each station to be stable when operating in isolation with a variable load. As regards individual stations, several special control problems concerned with individual plant items are discussed, such as: controlled reactivity insertions, temperature reactivity time constants and flow instability. A simplified analysis establishes a fundamental relationship between the stored thermal energy of a boiler unit (a function of mechanical construction) and the flexibility of the heat source (nuclear or fossil-fired) if the station is to cope satisfactorily with demands arising from unscheduled losses of other generating sets or transmission capacity. Two basic control schemes for power station operation are described known as 'coupled' and 'decoupled control'. Each of the control modes has its own merits, which depend on the proposed station operating strategy (base load or load following) and the nature of the heat source. (U.K.)

Ondergronds Station Blijdorp, Rotterdam

NARCIS (Netherlands)

Hijma, M.P.|info:eu-repo/dai/nl/266562426; Cohen, K.M.|info:eu-repo/dai/nl/185633374

2014-01-01

Het is in de herfst van 2005. Een lief meisje, Marieke, rijdt op haar vouwfiets door Rotterdam. Bij het Centraal Station is het al tijden een grote bouwplaats. Onder de nieuwe hal komt een veel groter metrostation en ook onder de Statenweg in Blijdorp is een grote bouwput voor een nieuw station.

GABA action in immature neocortical neurons directly depends on the availability of ketone bodies.

Science.gov (United States)

Rheims, Sylvain; Holmgren, Carl D; Chazal, Genevieve; Mulder, Jan; Harkany, Tibor; Zilberter, Tanya; Zilberter, Yuri

2009-08-01

In the early postnatal period, energy metabolism in the suckling rodent brain relies to a large extent on metabolic pathways alternate to glucose such as the utilization of ketone bodies (KBs). However, how KBs affect neuronal excitability is not known. Using recordings of single NMDA and GABA-activated channels in neocortical pyramidal cells we studied the effects of KBs on the resting membrane potential (E(m)) and reversal potential of GABA-induced anionic currents (E(GABA)), respectively. We show that during postnatal development (P3-P19) if neocortical brain slices are adequately supplied with KBs, E(m) and E(GABA) are both maintained at negative levels of about -83 and -80 mV, respectively. Conversely, a KB deficiency causes a significant depolarization of both E(m) (>5 mV) and E(GABA) (>15 mV). The KB-mediated shift in E(GABA) is largely determined by the interaction of the NKCC1 cotransporter and Cl(-)/HCO3 transporter(s). Therefore, by inducing a hyperpolarizing shift in E(m) and modulating GABA signaling mode, KBs can efficiently control the excitability of neonatal cortical neurons.

30 CFR 57.12085 - Transformer stations.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Transformer stations. 57.12085 Section 57.12085 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Underground Only § 57.12085 Transformer stations. Transformer stations shall be enclosed to prevent persons...

Reevaluation of air surveillance station siting

International Nuclear Information System (INIS)

Abbott, K.; Jannik, T.

2016-01-01

DOE Technical Standard HDBK-1216-2015 (DOE 2015) recommends evaluating air-monitoring station placement using the analytical method developed by Waite. The technique utilizes wind rose and population distribution data in order to determine a weighting factor for each directional sector surrounding a nuclear facility. Based on the available resources (number of stations) and a scaling factor, this weighting factor is used to determine the number of stations recommended to be placed in each sector considered. An assessment utilizing this method was performed in 2003 to evaluate the effectiveness of the existing SRS air-monitoring program. The resulting recommended distribution of air-monitoring stations was then compared to that of the existing site perimeter surveillance program. The assessment demonstrated that the distribution of air-monitoring stations at the time generally agreed with the results obtained using the Waite method; however, at the time new stations were established in Barnwell and in Williston in order to meet requirements of DOE guidance document EH-0173T.

Reevaluation of air surveillance station siting

Energy Technology Data Exchange (ETDEWEB)

Abbott, K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Jannik, T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-07-06

DOE Technical Standard HDBK-1216-2015 (DOE 2015) recommends evaluating air-monitoring station placement using the analytical method developed by Waite. The technique utilizes wind rose and population distribution data in order to determine a weighting factor for each directional sector surrounding a nuclear facility. Based on the available resources (number of stations) and a scaling factor, this weighting factor is used to determine the number of stations recommended to be placed in each sector considered. An assessment utilizing this method was performed in 2003 to evaluate the effectiveness of the existing SRS air-monitoring program. The resulting recommended distribution of air-monitoring stations was then compared to that of the existing site perimeter surveillance program. The assessment demonstrated that the distribution of air-monitoring stations at the time generally agreed with the results obtained using the Waite method; however, at the time new stations were established in Barnwell and in Williston in order to meet requirements of DOE guidance document EH-0173T.

Amtrak Stations

Data.gov (United States)

Department of Homeland Security — Updated database of the Federal Railroad Administration's (FRA) Amtrak Station database. This database is a geographic data set containing Amtrak intercity railroad...

Automatic Traffic Recorder (ATR) Stations

Data.gov (United States)

Department of Homeland Security — The data included in the GIS Traffic Stations Version database have been assimilated from station description files provided by FHWA for Weigh-in-Motion (WIM), and...

Radiation measurement on the International Space Station

International Nuclear Information System (INIS)

Akopova, A.B.; Manaseryan, M.M.; Melkonyan, A.A.; Tatikyan, S.Sh.; Potapov, Yu.

2005-01-01

The results of an investigation of radiation environment on board the ISS with apogee/perigee of 420/380km and inclination 51.6 o are presented. For measurement of important characteristics of cosmic rays (particles fluxes, LET spectrum, equivalent doses and heavy ions with Z>=2) a nuclear photographic emulsion as a controllable threshold detector was used. The use of this detector permits a registration of the LET spectrum of charged particles within wide range of dE/dx and during last years it has already been successfully used on board the MIR station, Space Shuttles and 'Kosmos' spacecrafts. An integral LET spectrum was measured in the range 0.5-2.2x103keV/μm and the value of equivalent dose 360μSv/day was estimated. The flux of biologically dangerous heavy particles with Z>=2 was measured (3.85x103particles/cm2)

Implementation of a network level protocol on a GIXINET type local network

International Nuclear Information System (INIS)

Loeuillet, J.L.

1987-11-01

The installation of a communication system for transferring results from several experiment laboratories to a computing center is described. The objectives of a useful bit rate of 24 kbs, low connection cost and simple infrastructure, extension of the network to 4 buildings situated within a radius of 300m, and connection in the most standardized fashion possible are attained by using the GIXINET local network and adopting the X25 packet protocol. Bit rates of 17.2 kbs for standard 128 octet packets, and 44 kbs for nonstandard packets (776 octets in this case) [fr

Knowledge based systems: A critical survey of major concepts, issues and techniques. Visuals

Science.gov (United States)

Dominick, Wayne D. (Editor); Kavi, Srinu

1984-01-01

This Working Paper Series entry represents a collection of presentation visuals associated with the companion report entitled, Knowledge Based Systems: A Critical Survey of Major Concepts, Issues, and Techniques, USL/DBMS NASA/RECON Working Paper Series report number DBMS.NASA/RECON-9. The objectives of the report are to: examine various techniques used to build the KBS; to examine at least one KBS in detail, i.e., a case study; to list and identify limitations and problems with the KBS; to suggest future areas of research; and to provide extensive reference materials.

Next Generation Hydrogen Station Composite Data Products: Retail Stations, Data through Quarter 4 of 2016

Energy Technology Data Exchange (ETDEWEB)

Sprik, Sam [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kurtz, Jennifer [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ainscough, Chris [National Renewable Energy Lab. (NREL), Golden, CO (United States); Saur, Genevieve [National Renewable Energy Lab. (NREL), Golden, CO (United States); Peters, Michael [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-05-31

This publication includes 86 composite data products (CDPs) produced for next generation hydrogen stations, with data through the fourth quarter of 2016. These CDPs include data from retail stations only.

Next Generation Hydrogen Station Composite Data Products: Retail Stations, Data through Quarter 2 of 2017

Energy Technology Data Exchange (ETDEWEB)

Sprik, Samuel [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kurtz, Jennifer M [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ainscough, Christopher D. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Saur, Genevieve [National Renewable Energy Lab. (NREL), Golden, CO (United States); Peters, Michael C. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-12-05

This publication includes 92 composite data products (CDPs) produced for next generation hydrogen stations, with data through the second quarter of 2017. These CDPs include data from retail stations only.

47 CFR 97.203 - Beacon station.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Beacon station. 97.203 Section 97.203... SERVICE Special Operations § 97.203 Beacon station. (a) Any amateur station licensed to a holder of a Technician, Technician Plus, General, Advanced or Amateur Extra Class operator license may be a beacon. A...

47 CFR 87.107 - Station identification.

Science.gov (United States)

2010-10-01

... station. Identify by one of the following means: (1) Aircraft radio station call sign. (2) The type of... type of aircraft followed by the last three characters of the registration marking. Notwithstanding any... of stations are exempted from the use of a call sign: Airborne weather radar, radio altimeter, air...

Emergency Medical Service (EMS) Stations

Data.gov (United States)

Kansas Data Access and Support Center — EMS Locations in Kansas The EMS stations dataset consists of any location where emergency medical services (EMS) personnel are stationed or based out of, or where...

Pumped energy transfer stations (STEP)

International Nuclear Information System (INIS)

Tournery, Jean-Francois

2015-12-01

As objectives of development are high for renewable energies (they are supposed to cover 50 per cent of new energy needs by 2035), pumped energy transfer stations are to play an important role in this respect. The author first discusses the consequences of the development of renewable energies on the exploitation of electric grids: issue of intermittency for some of them, envisaged solutions. Then, he addresses one of the solutions: the storage of electric power. He notices that increasing the potential energy of a volume of water is presently the most mature solution to face massive needs of the power system. Dams and pumped energy transfer stations represent now almost the whole installed storage power in the world. The author then presents these pumped energy transfer stations: principle, brief history (the first appeared in Italy and Switzerland at the end of the 1890's). He indicates the various parameters of assessment of such stations: maximum stored energy, installed power in pumping mode and turbine mode, time constant, efficiency, level of flexibility. He discusses economic issues. He describes and comments the operation of turbine-pump groups: ternary groups, reversible binary groups. He discusses barriers to be overcome and technical advances to be made for varying speed groups and for marine stations. He finally gives an overview (table with number of stations belonging to different power ranges, remarkable installations) of existing stations in China, USA, Japan, Germany, Austria, Spain, Portugal, Italy, Switzerland, France and UK, and indicate predictions regarding storage needs at the world level. Some data are finally indicated for the six existing French installations

RF-Station control crate

International Nuclear Information System (INIS)

Beuzekom, M.G. van; Es, J.T. van.

1992-01-01

This report gives a description of the electronic control-system for the RF-station of AmPS. The electronics form the connection between the computer-system and the hardware of the RF-station. Only the elements of the systems which are not described in the other NIKHEF-reports are here discussed in detail. (author). 7 figs

Nuclear power stations licensing

International Nuclear Information System (INIS)

Solito, J.

1978-04-01

The judicial aspects of nuclear stations licensing are presented. The licensing systems of the United States, Spain, France and Federal Republic of Germany are focused. The decree n 0 60.824 from July 7 sup(th), 1967 and the following legislation which define the systematic and area of competence in nuclear stations licensing are analysed [pt

Discharges from nuclear power stations

International Nuclear Information System (INIS)

1991-02-01

HM Inspectorate of Pollution commissioned, with authorising responsibilities in England and Wales, a study into the discharges of radioactive effluents from Nuclear Power Stations. The study considered arisings from nuclear power stations in Europe and the USA and the technologies to treat and control the radioactive discharges. This report contains details of the technologies used at many nuclear power stations to treat and control radioactive discharges and gives, where information was available, details of discharges and authorised discharge limits. (author)

Surry Power Station, Units 1 and 2. Semiannual operating report, July--December 1974

International Nuclear Information System (INIS)

1974-01-01

Net electric power generated by Surry Unit 1 was 6,930,353 MWH with the generator on line for 10,417.7 hours. Net electric power generated by Unit 2 was 5,699,299 MWH with the generator on line for 8,384.2 hours. Information is presented concerning operation, radioactive effluent releases, solid radioactive wastes, fuel shipments, occurrences in which temperature limitations on the condenser cooling water discharge were exceeded, changes in station organization, occupational personnel radiation exposure, nonradiological monitoring including thermal, physical, and biological programs, and the radiological environmental monitoring program. (U.S.)

Standardized Curriculum for Service Station Retailing.

Science.gov (United States)

Mississippi State Dept. of Education, Jackson. Office of Vocational, Technical and Adult Education.

This curriculum guide for service station retailing was developed by the state of Mississippi to standardize vocational education course titles and core contents. The objectives contained in this document are common to all service station retailing programs in the state. The guide contains objectives for service station retailing I and II courses.…

47 CFR 90.425 - Station identification.

Science.gov (United States)

2010-10-01

... stations. (4) It is any type of radiopositioning or radar station authorized in a service other than the... procedure. Except as provided for in paragraphs (d) and (e) of this section, each station or system shall be identified by the transmission of the assigned call sign during each transmission or exchange of...

47 CFR 80.519 - Station identification.

Science.gov (United States)

2010-10-01

... drawbridges may be identified by use of the name of the bridge in lieu of the call sign. Identification must...) Stations must identify transmissions by announcing in the English language the station's assigned call sign. In lieu of the identification of the station by voice, the official call sign may be transmitted by...

Cyanobacterial Diversity in Biological Soil Crusts along a Precipitation Gradient, Northwest Negev Desert, Israel.

Science.gov (United States)

Hagemann, Martin; Henneberg, Manja; Felde, Vincent J M N L; Drahorad, Sylvie L; Berkowicz, Simon M; Felix-Henningsen, Peter; Kaplan, Aaron

2015-07-01

Cyanobacteria occur worldwide but play an important role in the formation and primary activity of biological soil crusts (BSCs) in arid and semi-arid ecosystems. The cyanobacterial diversity in BSCs of the northwest Negev desert of Israel was surveyed at three fixed sampling stations situated along a precipitation gradient in the years 2010 to 2012. The three stations also are characterized by marked differences in soil features such as soil carbon, nitrogen, or electrical conductivity. The cyanobacterial biodiversity was analyzed by sequencing inserts of clone libraries harboring partial 16S rRNA gene sequences obtained with cyanobacteria-specific primers. Filamentous, non-diazotrophic strains (subsection III), particularly Microcoleus-like, dominated the cyanobacterial community (30% proportion) in all years. Specific cyanobacterial groups showed increased (e.g., Chroococcidiopsis, Leptolyngbya, and Nostoc strains) or decreased (e.g., unicellular strains belonging to the subsection I and Scytonema strains) abundances with declining water availability at the most arid, southern station, whereas many cyanobacterial strains were frequently found in the soils of all three stations. The cyanobacterial diversity at the three sampling stations appears dependent on the available precipitation, whereas the differences in soil chemistry were of lower importance.

47 CFR 80.1121 - Receipt and acknowledgement of distress alerts by ship stations and ship earth stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Receipt and acknowledgement of distress alerts by ship stations and ship earth stations. 80.1121 Section 80.1121 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES STATIONS IN THE MARITIME SERVICES Global Maritime Distress and Safety System (GMDSS)...

Power stations

International Nuclear Information System (INIS)

Cawte, H.; Philpott, E.F.

1980-01-01

The object is to provide a method of operating a dual purpose power station so that the steam supply system is operated at a high load factor. The available steam not required for electricity generation is used to provide process heat and the new feature is that the process plant capacity is determined to make the most economic use of the steam supply system, and not to match the passout capacity of the turbine of the turbogenerator. The product of the process plant should, therefore, be capable of being stored. A dual-purpose power station with a nuclear-powered steam source, turbogenerating means connected to the steam source and steam-powered process plant susceptible to wide variation in its rate of operation is described. (U.K.)

Fire protection concept for power stations

International Nuclear Information System (INIS)

Zitzmann, H.

The author shows how a systematic approach permits the design of a fire-protected power station. The special conditions of an individual power station are here treated as marginal conditions. The article describes how the concept is realized in the completed power station, taking account of the information provided by fire statistics. (orig.) [de

Backfilling of KBS-3V deposition tunnels - possibilities and limitations

Energy Technology Data Exchange (ETDEWEB)

Wimelius, Hans (Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)); Pusch, Roland (Geodevelopment International AB, Lund (Sweden))

2008-12-15

By definition for the SKB repository concept, the backfill of KBS-3V deposition tunnels must be so designed that transport of dissolved matter is controlled by diffusion and not by advective water flow. This requires that the hydraulic conductivity of the backfill does not exceed about E-10 m/s. The backfilling materials also have to adequately resist compression caused by upward expansion of the buffer. It must also exert an effective pressure of at least 100 kPa on the rock in order to provide support to the rock and minimize spalling of the rock. These criteria are fulfilled by several approaches and options for backfill materials, placed and compacted layer wise or in the form of blocks of compacted clay powder. Based on the experience from comprehensive lab studies and considering practical issues, SKB has selected a concept where the major part of the backfill consists of stacked blocks that are surrounded by clay pellets. Using this concept a basis for a detailed evaluation, a study of three different techniques for placing the blocks has been undertaken. The three block placement techniques examined are the 'Block', 'Robot', and 'Module' methods. They involve different block sizes and techniques for handling and placing the blocks but the same way of preparing the foundation bed of the blocks and placing the pellet filling. The blasted tunnels have a varying cross section, caused by the orientation of the blast-holes. This requires that a varying fraction of blocks be installed in the backfilling along the blasted tunnel interval if sufficiently high density and low hydraulic conductivity is to be achieved. The efficiency of filling will depend on the type of clay used in the blocks. For example, using Friedland clay for block preparation, the filling efficiency must be 80% while it can be reduced to 60% if more smectite-rich clay is used. The use of a clay with high smectite content increases margins and is concluded to be

Hydrogen Filling Station

Energy Technology Data Exchange (ETDEWEB)

Boehm, Robert F; Sabacky, Bruce; Anderson II, Everett B; Haberman, David; Al-Hassin, Mowafak; He, Xiaoming; Morriseau, Brian

2010-02-24

Hydrogen is an environmentally attractive transportation fuel that has the potential to displace fossil fuels. The Freedom CAR and Freedom FUEL initiatives emphasize the importance of hydrogen as a future transportation fuel. Presently, Las Vegas has one hydrogen fueling station powered by natural gas. However, the use of traditional sources of energy to produce hydrogen does not maximize the benefit. The hydrogen fueling station developed under this grant used electrolysis units and solar energy to produce hydrogen fuel. Water and electricity are furnished to the unit and the output is hydrogen and oxygen. Three vehicles were converted to utilize the hydrogen produced at the station. The vehicles were all equipped with different types of technologies. The vehicles were used in the day-to-day operation of the Las Vegas Valley Water District and monitoring was performed on efficiency, reliability and maintenance requirements. The research and demonstration utilized for the reconfiguration of these vehicles could lead to new technologies in vehicle development that could make hydrogen-fueled vehicles more cost effective, economical, efficient and more widely used. In order to advance the development of a hydrogen future in Southern Nevada, project partners recognized a need to bring various entities involved in hydrogen development and deployment together as a means of sharing knowledge and eliminating duplication of efforts. A road-mapping session was held in Las Vegas in June 2006. The Nevada State Energy Office, representatives from DOE, DOE contractors and LANL, NETL, NREL were present. Leadership from the National hydrogen Association Board of Directors also attended. As a result of this session, a roadmap for hydrogen development was created. This roadmap has the ability to become a tool for use by other road-mapping efforts in the hydrogen community. It could also become a standard template for other states or even countries to approach planning for a hydrogen

INTERACT Station Catalogue - 2015

DEFF Research Database (Denmark)

INTERACT stations are located in all major environmental envelopes of the Arctic providing an ideal platform for studying climate change and its impact on the environment and local communities. Since alpine environments face similar changes and challenges as the Arctic, the INTERACT network also ...... catalogue includes descriptions of 73 research stations included in the network at the time of printing....

Leadership at Antarctic Stations.

Science.gov (United States)

1987-03-01

Claseification 6. No. Pegees LEADERSHIP AT ANTARTIC STATIONS hxIs i4 5, C =r~eta(C), 17 Rfs~W (R, Udusiied U)J 7. No Refs 8. Author(s) Edocumesnt I...whether there is a "best" approach to leadership at an Antartic Station and what leadership style may have the most to offer. 3~~ __ ___ Tipesis to be

76 FR 19148 - PSEG Nuclear, LLC, Hope Creek Generating Station and Salem Nuclear Generating Station, Units 1...

Science.gov (United States)

2011-04-06

... NUCLEAR REGULATORY COMMISSION [Docket Nos. 50-272, 50-311, 50-354; NRC-2009-0390 and NRC-2009-0391] PSEG Nuclear, LLC, Hope Creek Generating Station and Salem Nuclear Generating Station, Units 1 and 2..., DPR-70, and DPR-75 for an additional 20 years of operation for the Hope Creek Generating Station (HCGS...

Choice of method - evaluation of strategies and systems for disposal of spent nuclear fuel

International Nuclear Information System (INIS)

2010-10-01

This report deals with the question of how the Swedish spent nuclear fuel is to be disposed of. What are the requirements? What are the alternatives? In the main chapter of the report, an evaluation is made of the KBS-3 method compared with other strategies and systems for final disposal of spent nuclear fuel. An appendix to the report presents in general terms how the KBS-3 method has developed from the end of the 1970s up to today. The report is one of a number of supporting documents for SKB's applications for construction and operation of the final repository for spent nuclear fuel. In parallel with and as a basis for the present report, SKB has prepared the reports Principer, strategier och system foer slutligt omhaendertagande av anvaent kaernbraensle ('Principles, strategies and systems for final disposal of spent nuclear fuel') /Grundfelt 2010a/, Jaemfoerelse mellan KBS-3-metoden och deponering i djupa borrhaal foer slutlig foervaring av anvaent kaernbraensle ('Comparison between the KBS-3 method and deposition in deep boreholes for final disposal of spent nuclear fuel') /Grundfelt 2010b/ and Utvecklingen av KBS-3- metoden. Genomgaang av forskningsprogram, saekerhetsanalyser, myndighetsgranskningar samt SKB:s internationella forskningssamarbete ('Development of the KBS-3 method. Review of research programmes, safety assessments, regulatory reviews and SKB's international research cooperation') /SKB 2010a/. The reports are in Swedish, but contain summaries in English. The first report is an update of the comprehensive account of alternative methods presented by SKB in 2000. The second report presents a comparison between the KBS-3 method and the Deep Boreholes concept, plus a status report on research and development in the area of Deep Boreholes. The last report describes how the KBS-3 method has been developed from the end of the 1970s up to today. It further describes how the method has been further developed and refined over the years, but also what the

Choice of method - evaluation of strategies and systems for disposal of spent nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

2010-10-15

This report deals with the question of how the Swedish spent nuclear fuel is to be disposed of. What are the requirements? What are the alternatives? In the main chapter of the report, an evaluation is made of the KBS-3 method compared with other strategies and systems for final disposal of spent nuclear fuel. An appendix to the report presents in general terms how the KBS-3 method has developed from the end of the 1970s up to today. The report is one of a number of supporting documents for SKB's applications for construction and operation of the final repository for spent nuclear fuel. In parallel with and as a basis for the present report, SKB has prepared the reports Principer, strategier och system foer slutligt omhaendertagande av anvaent kaernbraensle ('Principles, strategies and systems for final disposal of spent nuclear fuel') /Grundfelt 2010a/, Jaemfoerelse mellan KBS-3-metoden och deponering i djupa borrhaal foer slutlig foervaring av anvaent kaernbraensle ('Comparison between the KBS-3 method and deposition in deep boreholes for final disposal of spent nuclear fuel') /Grundfelt 2010b/ and Utvecklingen av KBS-3- metoden. Genomgaang av forskningsprogram, saekerhetsanalyser, myndighetsgranskningar samt SKB:s internationella forskningssamarbete ('Development of the KBS-3 method. Review of research programmes, safety assessments, regulatory reviews and SKB's international research cooperation') /SKB 2010a/. The reports are in Swedish, but contain summaries in English. The first report is an update of the comprehensive account of alternative methods presented by SKB in 2000. The second report presents a comparison between the KBS-3 method and the Deep Boreholes concept, plus a status report on research and development in the area of Deep Boreholes. The last report describes how the KBS-3 method has been developed from the end of the 1970s up to today. It further describes how the method has been further developed and

Methodology - evaluation of strategies -and the system for taking care of spent nuclear fuel; Metodval - utvaerdering av strategier och system foer att ta hand om anvaent kaernbraensle

Energy Technology Data Exchange (ETDEWEB)

2010-10-15

This report deals with the question of how the Swedish spent nuclear fuel is to be disposed of. What are the requirements? What are the alternatives? In the main chapter of the report, an evaluation is made of the KBS-3 method compared with other strategies and systems for final disposal of spent nuclear fuel. An appendix to the report presents in general terms how the KBS-3 method has developed from the end of the 1970s up to today. The report is one of a number of supporting documents for SKB's applications for construction and operation of the final repository for spent nuclear fuel. In parallel with and as a basis for the present report, SKB has prepared the reports 'Principer, strategier och system foer slutligt omhaendertagande av anvaent kaernbraensle' ('Principles, strategies and systems for final disposal of spent nuclear fuel') /Grundfelt 2010a/, 'Jaemfoerelse mellan KBS-3-metoden och deponering i djupa borrhaal foer slutlig foervaring av anvaent kaernbraensle' ('Comparison between the KBS-3 method and deposition in deep boreholes for final disposal of spent nuclear fuel') /Grundfelt 2010b/ and 'Utvecklingen av KBS-3-metoden. Genomgaang av forskningsprogram, saekerhetsanalyser, myndighetsgranskningar samt SKB:s internationella forskningssamarbete' ('Development of the KBS-3 method. Review of research programmes, safety assessments, regulatory reviews and SKB's international research cooperation') /SKB 2010a/. The reports are in Swedish, but contain summaries in English. The first report is an update of the comprehensive account of alternative methods presented by SKB in 2000. The second report presents a comparison between the KBS-3 method and the Deep Boreholes concept, plus a status report on research and development in the area of Deep Boreholes. The last report describes how the KBS-3 method has been developed from the end of the 1970s up to today. It further describes how the

Safety Distances for hydrogen filling stations

Energy Technology Data Exchange (ETDEWEB)

Matthijsen, A. J. C. M.; Kooi, E. S.

2005-07-01

In the Netherlands there is a growing interest in using natural gas as a transport fuel. The most important drivers behind this development are formed by poor inner city air quality and the decision to close several LPG filling stations. Dwellings are not allowed within the safety distances of 45 or 110 meters from the tanker filling point of these LPG stations, depending on the capacity of the station. Another driver is global warming. We are carrying out a study on station supply, compression, storage and filling for natural gas stations, and a similar, simultaneous study on hydrogen as a followup to our risk analysis for the hydrogen filling station in Amsterdam. Here, three buses drive on hydrogen as part of the European CUTE project. Driving on natural gas is an important step in the transition to cars on hydrogen. This study was commissioned by the Dutch Ministry of Spatial Planning, Housing and the Environment to advise on external safety aspects of future hydrogen filling stations. According to Dutch law homes may not be built within an individual risk contour of 10-6 per year of a dangerous object, such as a plant with hazardous materials or a filling station. An individual risk contour of 10-6 is represented by a line around a dangerous object that connects locations with an individual risk level of 10-6 per year. An individual 'located' within this contour line has a chance of one per million per year or more to be killed as a result of an accident caused by this object. The longest distance between the object and such a contour is called a 'safety distance'. A study on safety distances is now in progress for different kinds of hydrogen filling stations (e. g. gaseous and liquid hydrogen) and for different capacities, such as big, medium and small stations. The focus is on different kinds of hydrogen production and the hydrogen supply of the filling station. To decide on the design and supply of the hydrogen station, we examined the

Eco-technology service station: the future of gas station; Posto eco-tecnologico: o posto do futuro

Energy Technology Data Exchange (ETDEWEB)

Moura, Newton R. [PETROBRAS, Rio de Janeiro, RJ (Brazil); Daher, Humberto Antonio S. [PETROBRAS Distribuidora, Rio de Janeiro, RJ (Brazil)

2004-07-01

PETROBRAS Distribuidora and CENPES have a project to build an eco-technology service station at Ilha do Fundao, to know new technologies for vehicle fuelling, test of new vehicle natural gas compression system, and start projects with new fuels that are not available at Brazilian market. This service station concept shall be aligned with sustainability premise that are being established for both companies, that means, besides a technology focus, it shall have a social focus without any environment damage. PETROBRAS 'Board of Directors approved the expansion of PETROBRAS' Research and Development Center (CENPES) installations, including this service station construction. Some activities that will be developed at the service station are pointed out here: available of new natural gas compression system; micro-generation with micro turbine, fuel cell; and photo-voltaic cell technologies; hydrogen fuelling; oil-water system treatment; biodiesel fuelling. This station will have a show room opened to the public, with panels, videos and a CNG compressor in cut. (author)

Space Station Freedom food management

Science.gov (United States)

Whitehurst, Troy N., Jr.; Bourland, Charles T.

1992-01-01

This paper summarizes the specification requirements for the Space Station Food System, and describes the system that is being designed and developed to meet those requirements. Space Station Freedom will provide a mix of frozen, refrigerated, rehydratable, and shelf stable foods. The crew will pre-select preferred foods from an approved list, to the extent that proper nutrition balance is maintained. A galley with freezers, refrigerators, trash compactor, and combination microwave and convection ovens will improve crew efficiency and productivity during the long Space Station Freedom (SSF) missions.

Chilean Antarctic Stations on King George Island

Directory of Open Access Journals (Sweden)

Katsutada Kaminuma

2000-07-01

Full Text Available The purpose of my visit to Chilean Antarctic Stations was to assess the present status of geophysical observations and research, as the South Shetland Island, West Antarctica, where the stations are located, are one of the most active tectonic regions on the Antarctic plate. The Instituto Antartico Chileno (INACH kindly gave me a chance to stay in Frei/Escudero Bases as an exchange scientist under the Antarctic Treaty for two weeks in January 2000. I stayed in Frei Base as a member of a geological survey group named "Tectonic Evolution of the Antarctic Peninsula" which was organized by Prof. F. Herve, University of Chile, from January 05 to 19,2000. All my activity in the Antarctic was organized by INACH. During my stay in Frei Base, I also visited Bellingshausen (Russian, Great Wall (China and Artigas (Uruguay stations. All these stations are located within walking distance of Frei Base. King Sejong Station (Korea, located 10km east from Frei Base, and Jubany Base (Argentine, another 6km south-east from King Sejong Station, were also visited with the aid of a zodiac boat that was kindly operated for us by King Sejong Station. All stations except Escudero Base carry out meteorological observations. The seismological observations in Frei Base are operated by Washington State University of the U. S. monitoring of earthquake activity and three-component geomagnetic observations are done at King Sejong and Great Wall stations. Earth tide is monitored at Artigas Base. Continuous monitoring of GPS and gravity change are planned at King Sejong Station in the near future. Scientific research activities of each country in the area in the 1999/2000 Antarctic summer season were studied and the logistic ability of all stations was also assessed for our future international cooperation.

Thermo-mechanical effects from a KBS-3 type repository. Performance of pillars between repository tunnels

International Nuclear Information System (INIS)

Hakami, E.; Olofsson, Stig-Olof

2000-03-01

The aim of this study has been to investigate how the rock mass, in the near field of a KBS-3 type repository, will be affected by the excavation of tunnels and deposition holes and the thermal load from the deposited waste. The three-dimensional finite difference program FLAC 3D was used to perform numerical simulation of the rock mass behaviour. The rock mass was modelled as a homogeneous and isotropic continuum. The initial area heat intensity of the repository was assumed to be 10 W/m 2 in all models. The results show that in the middle of the pillar between the repository tunnels the temperature reaches a maximum of about 70 deg C after 55 years of deposition. The extent of areas where the rock is predicted to yield depends on the assumed quality of the rock mass and the initial in-situ stress field. The volume of yielded rock reaches a maximum after about 200 years after deposition. For a rock mass with internal friction angle of 45 deg and cohesion of 5 MPa (using a Mohr-Coulomb material model), the extent of yielded rock is limited to about 1.5 m behind the excavation periphery. The largest rock displacements are found in the tunnel floor at the upper part of the deposition holes. Tension and shear failure in the periphery of the excavations is predicted to occur during the rock excavation, with a depth extension depending on the magnitude and orientation of the in-situ stresses, as well as on the rock mass quality. Both the excavation effects and the then-no-mechanical effects are smallest when the major principal stress is oriented parallel with the deposition tunnels. The maximum convergence between tunnel walls was calculated to occur after 200 years and be about 9 mm, in the model assuming a rock mass with 5 MPa cohesion, 45 deg internal friction angle and maximum horizontal stress perpendicular to the tunnel. In this study confining effects from the buffer and backfill material was neglected. The effective stress concept was used in most of the models

Genetic variability of muscle biological characteristics of young limousin bulls

OpenAIRE

Renand, Gilles; Jurie, Catherine; Robelin, Jacques; Picard, Brigitte; Geay, Y.; Menissier, Francois

1995-01-01

Genetic parameters of 4 muscle biological characteristics (protein to DNA ratio (Pro/DNA), lactate dehydrogenase (LDH) activity, isocitrate dehydrogenase (ICDH) activity and the proportion of type I myosin heavy chains (MHC I)), in the Semitendinosus and the Longissimus thoracis, were estimated simultaneously with average daily gain (ADG), 480-d final weight (FW), carcass lean and fat contents (CL% and CF% respectively) in a sample of young Limousin bulls tested in station. The data came f...

Biological challenges of true space settlement

Science.gov (United States)

Mankins, John C.; Mankins, Willa M.; Walter, Helen

2018-05-01

"Space Settlements" - i.e., permanent human communities beyond Earth's biosphere - have been discussed within the space advocacy community since the 1970s. Now, with the end of the International Space Station (ISS) program fast approaching (planned for 2024-2025) and the advent of low cost Earth-to-orbit (ETO) transportation in the near future, the concept is coming once more into mainstream. Considerable attention has been focused on various issues associated with the engineering and human health considerations of space settlement such as artificial gravity and radiation shielding. However, relatively little attention has been given to the biological implications of a self-sufficient space settlement. Three fundamental questions are explored in this paper: (1) what are the biological "foundations" of truly self-sufficient space settlements in the foreseeable future, (2) what is the minimum scale for such self-sustaining human settlements, and (3) what are the integrated biologically-driven system requirements for such settlements? The paper examines briefly the implications of the answers to these questions in relevant potential settings (including free space, the Moon and Mars). Finally, this paper suggests relevant directions for future research and development in order for such space settlements to become viable in the future.

Ergonomic Application on the Work Station Layout

International Nuclear Information System (INIS)

Suharyo Widagdo; Darlis

2003-01-01

Work station layout in the ideal way has been made. The dimension of the work station is 9.4 m x 7.1 m. The workers to be stationed should feel comfort. This can be done by honoring the dimensions and the sum of the tools that should be stationed and also the free space that should be mention between the tools as state in EPRI, NP-2411. (author)

Operation feedback of hydrogen filling station

International Nuclear Information System (INIS)

Pregassame, S.; Barral, K.; Allidieres, L.; Charbonneau, T.; Lacombe, Y.

2004-01-01

One of the technical challenges of hydrogen technology is the development of hydrogen infrastructures which satisfy either safety requirements and reliability of filling processes. AIR LIQUIDE realized an hydrogen filling station in Sassenage (France) operational since September 2003. This station is able to fill 3 buses a day up to 350bar by equilibrium with high pressure buffers. In parallel with commercial stations, the group wanted to create a testing ground in real conditions running with several objectives: validate on a full scale bench a simulation tool able to predict the temperature of both gas and cylinder's materials during filling processes; define the best filling procedures in order to reach mass, temperature and filling time targets; analyse the temperature distribution and evolution inside the cylinder; get a general knowledge about hydrogen stations from safety and reliability point of view; operate the first full scale refuelling station in France. The station is also up-graded for 700bar filling from either a liquid hydrogen source or a gas booster, with cold filling possibility. This paper presents the results concerning 350bar filling : thermal effects, optimal filling procedures and influence of parameters such as climatic conditions are discussed. (author)

Lab-on-a-Chip: From Astrobiology to the International Space Station

Science.gov (United States)

Maule, Jake; Wainwright, Nor; Steele, Andrew; Gunter, Dan; Monaco, Lisa A.; Wells, Mark E.; Morris, Heather C.; Boudreaux, Mark E.

2008-01-01

The continual and long-term habitation of enclosed environments, such as Antarctic stations, nuclear submarines and space stations, raises unique engineering, medical and operational challenges. There is no easy way out and no easy way to get supplies in. This situation elevates the importance of monitoring technology that can rapidly detect events within the habitat that affect crew safety such as fire, release of toxic chemicals and hazardous microorganisms. Traditional methods to monitor microorganisms on the International Space Station (ISS) have consisted of culturing samples for 3-5 days and eventual sample return to Earth. To augment these culture methods with new, rapid molecular techniques, we developed the Lab-on-a-Chip Application Development - Portable Test System (LOCAD-PTS). The system consists of a hand-held spectrophotometer, a series of interchangeable cartridges and a surface sampling/dilution kit that enables crew to collect samples and detect a range of biological molecules, all within 15 minutes. LOCAD-PTS was launched to the ISS aboard Space Shuttle Discovery in December 2006, where it was operated for the first time during March-May 2007. The surfaces of five separate sites in the US Lab and Node 1 of ISS were analyzed for endotoxin, using cartridges that employ the Limulus Amebocyte Lysate (LAL) assay; results of these tests will be presented. LOCAD-PTS will remain permanently onboard ISS with new cartridges scheduled for launch in February and October of 2008 for the detection of fungi (Beta-glucan) and Gram-positive bacteria (lipoteichoic acid), respectively.

On the use of Space Station Freedom in support of the SEI - Life science research

Science.gov (United States)

Leath, K.; Volosin, J.; Cookson, S.

1992-01-01

The use of the Space Station Freedom (SSF) for life sciences research is evaluated from the standpoint of requirements for the Space Exploration Initiative (SEI). SEI life sciences research encompasses: (1) biological growth and development in space; (2) life support and environmental health; (3) physiological/psychological factors of extended space travel; and (4) space environmental factors. The platforms required to support useful study in these areas are listed and include ground-based facilities, permanently manned spacecraft, and the Space Shuttle. The SSF is shown to be particularly applicable to the areas of research because its facilities can permit the study of gravitational biology, life-support systems, and crew health. The SSF can serve as an experimental vehicle to derive the required knowledge needed to establish a commitment to manned Mars missions and colonization plans.

47 CFR 73.6017 - Digital Class A TV station protection of Class A TV and digital Class A TV stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Digital Class A TV station protection of Class A TV and digital Class A TV stations. 73.6017 Section 73.6017 Telecommunication FEDERAL... Broadcast Stations § 73.6017 Digital Class A TV station protection of Class A TV and digital Class A TV...

Centrifuge Facility for the International Space Station Alpha

Science.gov (United States)

Johnson, Catherine C.; Hargens, Alan R.

1994-01-01

The Centrifuge Facility planned for the International Space Station Alpha has under-one considerable redesign over the past year, primarily because the Station is now viewed as a 10 year mission rather than a 30 year mission and because of the need to simply the design to meet budget constraints and a 2000 launch date. The basic elements of the Centrifuge Facility remain the same, i.e., a 2.5 m diameter centrifuge, a micro-g holding unit, plant and animal habitats, a glovebox and a service unit. The centrifuge will still provide the full range of artificial gravity from 0.01 a to 2 - as originally planned; however, the extractor to permit withdrawal of habitats from the centrifuge without stopping the centrifuge has been eliminated. The specimen habitats have also been simplified and are derived from other NASA programs. The Plant Research Unit being developed by the Gravitational Biology Facility will be used to house plants in the Centrifuge Facility. Although not as ambitious as the Centrifuge Facility plant habitat, it will provide much better environmental control and lighting than the current Shuttle based Plant Growth Facility. Similarly, rodents will be housed in the Advanced Animal Habitat being developed for the Shuttle program. The Centrifuge Facility and ISSA will provide the opportunity to perform repeatable, high quality science. The long duration increments available on the Station will permit multigeneration studies on both plants and animals which have not previously been possible. The Centrifuge Facility will accommodate sufficient number of specimens to permit statistically significant sampling of specimens to investigate the time course of adaptation to altered gravity environments. The centrifuge will for the first time permit investigators to use gravity itself as a tool to investigate fundamental processes, to investigate the intensity and duration of gravity to maintain normal structure and function, to separate the effects of micro-g from

Biological and Physical Space Research Laboratory 2002 Science Review

Science.gov (United States)

Curreri, P. A. (Editor); Robinson, M. B. (Editor); Murphy, K. L. (Editor)

2003-01-01

With the International Space Station Program approaching core complete, our NASA Headquarters sponsor, the new Code U Enterprise, Biological and Physical Research, is shifting its research emphasis from purely fundamental microgravity and biological sciences to strategic research aimed at enabling human missions beyond Earth orbit. Although we anticipate supporting microgravity research on the ISS for some time to come, our laboratory has been vigorously engaged in developing these new strategic research areas.This Technical Memorandum documents the internal science research at our laboratory as presented in a review to Dr. Ann Whitaker, MSFC Science Director, in July 2002. These presentations have been revised and updated as appropriate for this report. It provides a snapshot of the internal science capability of our laboratory as an aid to other NASA organizations and the external scientific community.

Alternative Fuels Data Center: Ethanol Fueling Stations

Science.gov (United States)

... More in this section... Ethanol Basics Benefits & Considerations Stations Locations Infrastructure fueling stations by location or along a route. Infrastructure Development Learn about ethanol fueling infrastructure; codes, standards, and safety; and ethanol equipment options. Maps & Data E85 Fueling Station

[Habitability and biological life support systems for man].

Science.gov (United States)

Gazenko, O G; Grigor'ev, A I; Meleshko, G I; Shepelev, E Ia

1990-01-01

This paper discusses general concepts and specific details of the habitability of space stations and planetary bases completely isolated from the Earth for long periods of time. It emphasizes inadequacy of the present-day knowledge about natural conditions that provide a biologically acceptable environment on the Earth as well as lack of information about life support systems as a source of consumables (oxygen, water, food) and a tool for waste management. The habitability of advanced space vehicles is closely related to closed bioregenerative systems used as life support systems.

Statistical Inference for a two station tandem queue with atmost one customer to wait between the stations

Directory of Open Access Journals (Sweden)

Vaidya Nathan

2012-03-01

Full Text Available A maximum likelihood estimator (MLE, a consistent asymptotically normal (CAN estimator and asymptotic confidence limits for the expected number of customers in the system for a sequential two station, single server system with Poisson input and exponential service, where no queue is allowed in front of station 1 and atmost one customer is allowed to wait between the stations and with blocking are obtained.

Sources of the wind power stations

International Nuclear Information System (INIS)

Chudivani, J.; Huettner, L.

2012-01-01

The paper deals with problems of the wind power stations. Describes the basic properties of wind energy. Shows and describes the different types of electrical machines used as a source of electricity in the wind power stations. Shows magnetic fields synchronous generator with salient poles and permanent magnets in the program FEMM. Describes methods for assessing of reversing the effects of the wind power stations on the distribution network. (Authors)

Water pollution and thermal power stations

International Nuclear Information System (INIS)

Maini, A.; Harapanahalli, A.B.

1993-01-01

There are a number of thermal power stations dotting the countryside in India for the generation of electricity. The pollution of environment is continuously increasing in the country with the addition of new coal based power stations and causing both a menace and a hazard to the biota. The paper reviews the problems arising out of water pollution from the coal based thermal power stations. (author). 2 tabs

WVU Hydrogen Fuel Dispensing Station

Energy Technology Data Exchange (ETDEWEB)

Davis, William [West Virginia University Research Corporation, Morgantown, WV (United States)

2015-09-01

The scope of this project was changed during the course of the project. Phase I of the project was to construct a site similar to the site at Central West Virginia Regional Airport in Charleston, WV to show that duplication of the site was a feasible method of conducting hydrogen stations. Phase II of the project was necessitated due to a lack of funding that was planned for the development of the station in Morgantown. The US Department of Energy determined that the station in Charleston would be dismantled and moved to Morgantown and reassembled at the Morgantown site. This necessitated storage of the components of the station for almost a year at the NAFTC Headquarters which caused a number of issues with the equipment that will be discussed in later portions of this report. This report will consist of PHASE I and PHASE II with discussions on each of the tasks scheduled for each phase of the project.

Oceanographic data collected from SATURN River Station 05 by Center for Coastal Margin Observation and Prediction (CMOP) and assembled by Northwest Association of Networked Ocean Observation Systems (NANOOS) in the Columbia River Estuary and North East Pacific Ocean from 2009-06-23 to 2016-12-06 (NCEI Accession 0162430)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — NCEI Accession 0162430 contains biological, chemical, navigational and physical data collected at SATURN River Station 05, a fixed station in the Columbia River...

Oceanographic data collected from Saturn Estuary Station 01 by Center for Coastal Margin Observation and Prediction (CMOP) and assembled by Northwest Association of Networked Ocean Observation Systems (NANOOS) in the Columbia River Estuary and North East Pacific Ocean from 2008-04-13 to 2017-07-01 (NCEI Accession 0162182)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — NCEI Accession 0162182 contains biological, chemical and physical data collected at Saturn Estuary Station 01, a fixed station in the Columbia River estuary -...

Oceanographic data collected from Saturn Estuary Station 03 by Center for Coastal Margin Observation and Prediction (CMOP) and assembled by Northwest Association of Networked Ocean Observation Systems (NANOOS) in the Columbia River Estuary and North East Pacific Ocean from 2008-04-19 to 2017-08-01 (NCEI Accession 0162617)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — NCEI Accession 0162617 contains biological, chemical and physical data collected at Saturn Estuary Station 03, a fixed station in the Columbia River estuary -...

Background noise spectra of global seismic stations

Energy Technology Data Exchange (ETDEWEB)

Wada, M.M.; Claassen, J.P.

1996-08-01

Over an extended period of time station noise spectra were collected from various sources for use in estimating the detection and location performance of global networks of seismic stations. As the database of noise spectra enlarged and duplicate entries became available, an effort was mounted to more carefully select station noise spectra while discarding others. This report discusses the methodology and criteria by which the noise spectra were selected. It also identifies and illustrates the station noise spectra which survived the selection process and which currently contribute to the modeling efforts. The resulting catalog of noise statistics not only benefits those who model network performance but also those who wish to select stations on the basis of their noise level as may occur in designing networks or in selecting seismological data for analysis on the basis of station noise level. In view of the various ways by which station noise were estimated by the different contributors, it is advisable that future efforts which predict network performance have available station noise data and spectral estimation methods which are compatible with the statistics underlying seismic noise. This appropriately requires (1) averaging noise over seasonal and/or diurnal cycles, (2) averaging noise over time intervals comparable to those employed by actual detectors, and (3) using logarithmic measures of the noise.

Space Station galley design

Science.gov (United States)

Trabanino, Rudy; Murphy, George L.; Yakut, M. M.

1986-01-01

An Advanced Food Hardware System galley for the initial operating capability (IOC) Space Station is discussed. Space Station will employ food hardware items that have never been flown in space, such as a dishwasher, microwave oven, blender/mixer, bulk food and beverage dispensers, automated food inventory management, a trash compactor, and an advanced technology refrigerator/freezer. These new technologies and designs are described and the trades, design, development, and testing associated with each are summarized.

The Human Capital of Knowledge Brokers: An analysis of attributes, capacities and skills of academic teaching and research faculty at Kenyan schools of public health.

Science.gov (United States)

Jessani, Nasreen; Kennedy, Caitlin; Bennett, Sara

2016-08-02

Academic faculty involved in public health teaching and research serve as the link and catalyst for knowledge synthesis and exchange, enabling the flow of information resources, and nurturing relations between 'two distinct communities' - researchers and policymakers - who would not otherwise have the opportunity to interact. Their role and their characteristics are of particular interest, therefore, in the health research, policy and practice arena, particularly in low- and middle-income countries. We investigated the individual attributes, capacities and skills of academic faculty identified as knowledge brokers (KBs) in schools of public health (SPH) in Kenya with a view to informing organisational policies around the recruitment, retention and development of faculty KBs. During April 2013, we interviewed 12 academics and faculty leadership (including those who had previously been identified as KBs) from six SPHs in Kenya, and 11 national health policymakers with whom they interact. Data were qualitatively analyzed using inductive thematic analysis to unveil key characteristics. Key characteristics of KBs fell into five categories: sociodemographics, professional competence, experiential knowledge, interactive skills and personal disposition. KBs' reputations benefitted from their professional qualifications and content expertise. Practical knowledge in policy-relevant situations, and the related professional networks, allowed KB's to navigate both the academic and policy arenas and also to leverage the necessary connections required for policy influence. Attributes, such as respect and a social conscience, were also important KB characteristics. Several changes in Kenya are likely to compel academics to engage increasingly with policymakers at an enhanced level of debate, deliberation and discussion in the future. By recognising existing KBs, supporting the emergence of potential KBs, and systematically hiring faculty with KB-specific characteristics, SPHs can

The validity and reliability of the StationMaster: a device to improve the accuracy of station assessment in labour.

Science.gov (United States)

Awan, Noveen; Rhoades, Anthony; Weeks, Andrew D

2009-07-01

To compare the accuracy of digital assessment and the StationMaster (SM) in the assessment of fetal head station. The SM is a simple modification of the amniotomy hook which works by relocating the point of reference for station assessment from the ischial spines to the posterior fourchette. It is first adjusted to the woman's pelvic size, and then inserted into the vagina until it touches the fetal head. The station is then read off at the posterior fourchette in cm. An in vitro study of test validity and reliability was conducted at Liverpool Women's Hospital, Liverpool, UK. An apparatus was constructed in which a model fetal head could be accurately positioned within a mannequin's pelvis. Twenty midwives and 20 doctors (in current labour ward practice) gave their consent to take part. First, the head was placed in 5 random stations (-2 to +7 cm) and the participant asked to record their digital assessment for each. The participant was then taught to use the SM and the experiment repeated with 5 new stations. The complete experiment was repeated at least 2 weeks later using the same stations but in reverse order. The true values were compared with both the digital and SM assessments using mean differences with 95% limits of agreement. The repeatability of the two methods was assessed in the same way. Overall, the SM was more accurate than digital examination. The mean error (S.D.) ranged from 0.1 (1.2) to 2.6 (1.6) for the StationMaster and 0.3 (1.3) to 4.3 (1.1) for digital examination. Inaccuracies increased as the head descended through the pelvis. When assessed digitally, the true value fell outside one standard deviation for stations of more than +1cm. In contrast, with the SM the true value remained inside one standard deviation for all stations up to +5. In vitro the SM improves the accuracy of intrapartum station assessment.

Space Station - Opportunity for international cooperation and utilization

Science.gov (United States)

Pedersen, K. S.

1984-01-01

In connection with his announcement regarding the development of a permanently manned Space Station, President Reagan invited the United States' friends and allies to join in the Space Station program. The President's invitation was preceded by more than two years of interaction between NASA and some of its potential partners in Space Station planning activities. Attention is given to international participation in Space Station planning, international cooperation on the Space Station, the guidelines for international cooperation, and the key challenges. Questions regarding quid pro quos are considered along with aspects of technology transfer, commercial use, problems of management, and the next steps concerning the Space Station program.

Utilities respond to nuclear station blackout rule

International Nuclear Information System (INIS)

Rubin, A.M.; Beasley, B.; Tenera, L.P.

1990-01-01

The authors discuss how nuclear plants in the United States have taken actions to respond to the NRC Station Blackout Rule, 10CFR50.63. The rule requires that each light water cooled nuclear power plant licensed to operate must be able to withstand for a specified duration and recover from a station blackout. Station blackout is defined as the complete loss of a-c power to the essential and non-essential switch-gear buses in a nuclear power plant. A station blackout results from the loss of all off-site power as well as the on-site emergency a-c power system. There are two basic approaches to meeting the station blackout rule. One is to cope with a station blackout independent of a-c power. Coping, as it is called, means the ability of a plant to achieve and maintain a safe shutdown condition. The second approach is to provide an alternate a-c power source (AAC)

Torness: proposed nuclear power station

International Nuclear Information System (INIS)

Anon.

1979-01-01

The need for and desirability of nuclear power, and in particular the proposed nuclear power station at Torness in Scotland, are questioned. Questions are asked, and answered, on the following topics: position, appearance and cost of the proposed Torness plant, and whether necessary; present availability of electricity, and forecast of future needs, in Scotland; energy conservation and alternative energy sources; radiation hazards from nuclear power stations (outside, inside, and in case of an accident); transport of spent fuel from Torness to Windscale; radioactive waste management; possibility of terrorists making a bomb with radioactive fuel from a nuclear power station; cost of electricity from nuclear power; how to stop Torness. (U.K.)

76 FR 24538 - Duke Energy Carolinas, LLC; Catawba Nuclear Station, Units 1 and 2; McGuire Nuclear Station...

Science.gov (United States)

2011-05-02

... NUCLEAR REGULATORY COMMISSION [Docket Nos. 50-413 and 50-414; NRC-2011-0100; Docket Nos. 50-369 and 50-370; Docket Nos. 50-269, 50-270, and 50-287] Duke Energy Carolinas, LLC; Catawba Nuclear Station, Units 1 and 2; McGuire Nuclear Station, Units 1 and 2; Oconee Nuclear Station, Units 1, 2, and 3...

47 CFR 73.6011 - Protection of TV broadcast stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Protection of TV broadcast stations. 73.6011... RADIO BROADCAST SERVICES Class A Television Broadcast Stations § 73.6011 Protection of TV broadcast stations. Class A TV stations must protect authorized TV broadcast stations, applications for minor changes...

Backfilling of KBS-3V deposition tunnels - possibilities and limitations

International Nuclear Information System (INIS)

Wimelius, Hans; Pusch, Roland

2008-12-01

By definition for the SKB repository concept, the backfill of KBS-3V deposition tunnels must be so designed that transport of dissolved matter is controlled by diffusion and not by advective water flow. This requires that the hydraulic conductivity of the backfill does not exceed about E-10 m/s. The backfilling materials also have to adequately resist compression caused by upward expansion of the buffer. It must also exert an effective pressure of at least 100 kPa on the rock in order to provide support to the rock and minimize spalling of the rock. These criteria are fulfilled by several approaches and options for backfill materials, placed and compacted layer wise or in the form of blocks of compacted clay powder. Based on the experience from comprehensive lab studies and considering practical issues, SKB has selected a concept where the major part of the backfill consists of stacked blocks that are surrounded by clay pellets. Using this concept a basis for a detailed evaluation, a study of three different techniques for placing the blocks has been undertaken. The three block placement techniques examined are the 'Block', 'Robot', and 'Module' methods. They involve different block sizes and techniques for handling and placing the blocks but the same way of preparing the foundation bed of the blocks and placing the pellet filling. The blasted tunnels have a varying cross section, caused by the orientation of the blast-holes. This requires that a varying fraction of blocks be installed in the backfilling along the blasted tunnel interval if sufficiently high density and low hydraulic conductivity is to be achieved. The efficiency of filling will depend on the type of clay used in the blocks. For example, using Friedland clay for block preparation, the filling efficiency must be 80% while it can be reduced to 60% if more smectite-rich clay is used. The use of a clay with high smectite content increases margins and is concluded to be superior from emplacement point

Theoretical and practical investigation of the electromagnetic radiation fields from the Sabborah radio broadcasting station

International Nuclear Information System (INIS)

Kharita, M. H.; Abo Kasem, I.; Kattab, A.

2008-01-01

This work has special importance as it aims at the investigation of the electromagnetic radiation from the Sabborah radio broadcasting station. The report includes general introduction to the physics of the electromagnetic fields and the biological effects of these fields and consequently its health effects. The bases of the recommended exposure limits according to the International Commission on Non-Ionizing Radiation Protection (ICNIRP) have been discussed in addition to the theoretical and practical investigations. This report summarizes the results of this study and the final recommendations. (author)

47 CFR 97.5 - Station license required.

Science.gov (United States)

2010-10-01

.... (3) A military recreation station license grant. A military recreation station license grant may be... States military recreational premises where the station is situated. The person must not be a... the balance of the license term and the suspension is still in effect, suspended for the balance of...

A facility for training Space Station astronauts

Science.gov (United States)

Hajare, Ankur R.; Schmidt, James R.

1992-01-01

The Space Station Training Facility (SSTF) will be the primary facility for training the Space Station Freedom astronauts and the Space Station Control Center ground support personnel. Conceptually, the SSTF will consist of two parts: a Student Environment and an Author Environment. The Student Environment will contain trainers, instructor stations, computers and other equipment necessary for training. The Author Environment will contain the systems that will be used to manage, develop, integrate, test and verify, operate and maintain the equipment and software in the Student Environment.

A conveyor system for feeding work stations

International Nuclear Information System (INIS)

Sheader, J.; Davies, K.J.

1986-01-01

A conveyor system comprises carriages drive, e.g. by a linear motor, a pre-arranged sequence of steps to move workpieces in forward and reverse directions between work stations. Each work station has a part position and a work position and each carriage has a number of compartments for workpieces spaced apart at a pitch equal to the spacing between the part and work positions at each station. Transfer means at the work stations move workpieces between the carriage compartments and the part and work positions. The workpieces can be nuclear fuel pins mounted in carriers and the carriages shuttle to and fro between adjacent stations to move fuel pins and carriers in a forward direction and the return empty carriers in a reverse direction. (author)

47 CFR 80.123 - Service to stations on land.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Service to stations on land. 80.123 Section 80... STATIONS IN THE MARITIME SERVICES Operating Requirements and Procedures Special Procedures-Public Coast Stations § 80.123 Service to stations on land. Marine VHF public coast stations, including AMTS coast...

TEPCO plans to construct Higashidori Nuclear Power Station

International Nuclear Information System (INIS)

Tsuruta, Atsushi

2008-01-01

In 2006, TEPCO submitted to the government plans for the construction of Higashidori Nuclear Power Station. The application was filed 41 years after the project approved by the Higashidori Village Assembly. This nuclear power station will be the first new nuclear power plant constructed by TEPCO since the construction of Units No.6 and 7 at the Kashiwazaki Kariwa Nuclear Power Station 18 years ago. Higashidori Nuclear Power Station is to be constructed at a completely new site, which will become the fourth TEPCO nuclear power station. Higashidori Nuclear Power Station Unit No.1 will be TEPCO's 18th nuclear reactor. Unit No.1 will be an advanced boiling water reactor (ABWR), a reactor-type with a proven track record. It will be TEPCO's third ABWR. Alongside incorporating the latest technology, in Higashidori Nuclear Power Station Unit No.1, the most important requirement is for TEPCO to reflect in the new unit information and experience acquired from the operation of other reactors (information and experience acquired through the experience of operating TEPCO's 17 units at Fukushima Daiichi Nuclear Power Station, Fukushima Daini Nuclear Power Station and Kashiwazaki Kashiwa Nuclear Power Station in addition to information on non-conformities at nuclear power stations in Japan and around the world). Higashidori Nuclear Power Station is located in Higashidori-Village (Aomori Prefecture) and the selected site includes a rich natural environment. From an environmental perspective, we will implement the construction with due consideration for the land and sea environment, aiming to ensure that the plant can co-exist with its natural surroundings. The construction plans are currently being reviewed by the Nuclear and Industrial Safety Agency. We are committed to making progress in the project for the start of construction and subsequent commercial operation. (author)

42 CFR 35.1 - Hospital and station rules.

Science.gov (United States)

2010-10-01

... EXAMINATIONS HOSPITAL AND STATION MANAGEMENT General § 35.1 Hospital and station rules. The officer in charge of a station or hospital of the Service is authorized to adopt such rules and issue such instructions... 42 Public Health 1 2010-10-01 2010-10-01 false Hospital and station rules. 35.1 Section 35.1...

Studies of the reproductive biology of deep-sea megabenthos

International Nuclear Information System (INIS)

Tyler, P.A.

1987-07-01

The final report describes the general biology and ecology of the 15 holothurians, 3 asteroids, 2 zoanthids and 1 crustacea species studied in Reports I-XIII, the sampling methods used and the station data. A summary of the histological, histochemical and biochemical results for the species examined is given. The data suggest that the reproductive processes in the deep-sea species examined are highly unlikely to be part of a pathway for the transfer of radionuclides from the deep-sea back to man. (author)

METALLOGRAPHIC SAMPLE PREPARATION STATION-CONSTRUCTIVE CONCEPT

Directory of Open Access Journals (Sweden)

AVRAM Florin Timotei

2016-11-01

Full Text Available In this paper we propose to present the issues involved in the case of the constructive conception of a station for metallographic sample preparation. This station is destined for laboratory work. The metallographic station is composed of a robot ABB IRB1600, a metallographic microscope, a gripping device, a manipulator, a laboratory grinding and polishing machine. The robot will be used for manipulation of the sample preparation and the manipulator take the sample preparation for processing.

NRC's object-oriented simulator instructor station

International Nuclear Information System (INIS)

Griffin, J.I.; Griffin, J.P.

1995-06-01

As part of a comprehensive simulator upgrade program, the simulator computer systems associated with the Nuclear Regulatory Commission's (NRC) nuclear power plant simulators were replaced. Because the original instructor stations for two of the simulators were dependent on the original computer equipment, it was necessary to develop and implement new instructor stations. This report describes the Macintosh-based Instructor Stations developed by NRC engineers for the General Electric (GE) and Babcock and Wilcox (B and W) simulators

Solar-Assisted Electric Vehicle Charging Station Interim Report

Energy Technology Data Exchange (ETDEWEB)

Lapsa, Melissa Voss [ORNL; Durfee, Norman [ORNL; Maxey, L Curt [ORNL; Overbey, Randall M [ORNL

2011-09-01

Oak Ridge National Laboratory (ORNL) has been awarded $6.8 million in the Department of Energy (DOE) American Recovery and Reinvestment Act (ARRA) funds as part of an overall $114.8 million ECOtality grant with matching funds from regional partners to install 125 solar-assisted Electric Vehicle (EV) charging stations across Knoxville, Nashville, Chattanooga, and Memphis. Significant progress has been made toward completing the scope with the installation of 25 solar-assisted charging stations at ORNL; six stations at Electric Power Research Institute (EPRI); and 27 stations at Nissan's Smyrna and Franklin sites, with three more stations under construction at Nissan's new lithium-ion battery plant. Additionally, the procurement process for contracting the installation of 34 stations at Knoxville, the University of Tennessee Knoxville (UTK), and Nashville sites is underway with completion of installation scheduled for early 2012. Progress is also being made on finalizing sites and beginning installations of 30 stations in Nashville, Chattanooga, and Memphis by EPRI and Tennessee Valley Authority (TVA). The solar-assisted EV charging station project has made great strides in fiscal year 2011. A total of 58 solar-assisted EV parking spaces have been commissioned in East and Middle Tennessee, and progress on installing the remaining 67 spaces is well underway. The contract for the 34 stations planned for Knoxville, UTK, and Nashville should be underway in October with completion scheduled for the end of March 2012; the remaining three Nissan stations are under construction and scheduled to be complete in November; and the EPRI/TVA stations for Chattanooga, Vanderbilt, and Memphis are underway and should be complete by the end of March 2012. As additional Nissan LEAFs are being delivered, usage of the charging stations has increased substantially. The project is on course to complete all 125 solar-assisted EV charging stations in time to collect meaningful data

Historical parallels of biological space experiments from Soyuz, Salyut and Mir to Shenzhou flights

Science.gov (United States)

Nechitailo, Galina S.; Kondyurin, Alexey

2016-07-01

Human exploitation of space is a great achievement of our civilization. After the first space flights a development of artificial biological environment in space systems is a second big step. First successful biological experiments on a board of space station were performed on Salyut and Mir stations in 70-90th of last century such as - first long time cultivation of plants in space (wheat, linen, lettuce, crepis); - first flowers in space (Arabidopsis); - first harvesting of seeds in space (Arabidopsis); - first harvesting of roots (radish); - first full life cycle from seeds to seeds in space (wheat), Guinness recorded; - first tissue culture experiments (Panax ginseng L, Crocus sativus L, Stevia rebaundiana B; - first tree growing in space for 2 years (Limonia acidissima), Guinness recorded. As a new wave, the modern experiments on a board of Shenzhou Chinese space ships are performed with plants and tissue culture. The space flight experiments are now focused on applications of the space biology results to Earth technologies. In particular, the tomato seeds exposed 6 years in space are used in pharmacy industry in more then 10 pharmaceutical products. Tissue culture experiments are performed on the board of Shenzhou spaceship for creation of new bioproducts including Space Panax ginseng, Space Spirulina, Space Stetatin, Space Tomato and others products with unique properties. Space investments come back.

Space Station Environmental Control/Life Support System engineering

Science.gov (United States)

Miller, C. W.; Heppner, D. B.

1985-01-01

The present paper is concerned with a systems engineering study which has provided an understanding of the overall Space Station ECLSS (Environmental Control and Life Support System). ECLSS/functional partitioning is considered along with function criticality, technology alternatives, a technology description, single thread systems, Space Station architectures, ECLSS distribution, mechanical schematics per space station, and Space Station ECLSS characteristics. Attention is given to trade studies and system synergism. The Space Station functional description had been defined by NASA. The ECLSS will utilize technologies which embody regenerative concepts to minimize the use of expendables.

MHD power station with coal gasification

International Nuclear Information System (INIS)

Brzozowski, W.S.; Dul, J.; Pudlik, W.

1976-01-01

A description is given of the proposed operating method of a MHD-power station including a complete coal gasification into lean gas with a simultaneous partial gas production for the use of outside consumers. A comparison with coal gasification methods actually being used and full capabilities of power stations heated with coal-derived gas shows distinct advantages resulting from applying the method of coal gasification with waste heat from MHD generators working within the boundaries of the thermal-electric power station. (author)

Adding Learning to Knowledge-Based Systems: Taking the "Artificial" Out of AI

Science.gov (United States)

Daniel L. Schmoldt

1997-01-01

Both, knowledge-based systems (KBS) development and maintenance require time-consuming analysis of domain knowledge. Where example cases exist, KBS can be built, and later updated, by incorporating learning capabilities into their architecture. This applies to both supervised and unsupervised learning scenarios. In this paper, the important issues for learning systems-...

Effects of insulin on ketogenesis following fasting in lean and obese men

NARCIS (Netherlands)

Soeters, Maarten R.; Sauerwein, Hans P.; Faas, Linda; Smeenge, Martijn; Duran, Marinus; Wanders, Ronald J.; Ruiter, An F.; Ackermans, Mariëtte T.; Fliers, Eric; Houten, Sander M.; Serlie, Mireille J.

2009-01-01

The ketone bodies (KBs) D-3-hydroxybutyrate (D-3HB) and acetoacetate (AcAc) play a role in starvation and have been associated with insulin resistance. The dose-response relationship between insulin and KBs was demonstrated to be shifted to the right in type 2 diabetes patients. However, KB levels

Power station impacts: socio-economic impact assessment

International Nuclear Information System (INIS)

Glasson, John; Elson, Martin; Barrett, Brendan; Wee, D. Van der

1987-01-01

The aim of this study is to assess the local social and economic impacts of a proposed nuclear power station development at Hinkley Point in Somerset. The proposed development, Hinkley Point C, would be an addition to the existing Hinkley Point A Magnox station, commissioned in 1965, and the Hinkley Point B Advanced Gas Cooled Reactor (AGR) station, commissioned in 1976. It is hoped that the study will be of assistance to the CEGB, the Somerset County and District Councils and other agencies in their studies of the proposed development. In addition, the study seeks to apply and further develop the methodology and results from previous studies by the Power Station Impacts (PSI) team for predicting the social and economic effects of proposed power station developments on their localities. (author)

Black carbon at a coastal Antarctic station (Syowa Station: seasonal variation and transport processes

Directory of Open Access Journals (Sweden)

Keiichiro Hara

2010-12-01

Full Text Available Measurement of atmospheric black carbon (BC was carried out at Syowa Station Antarctica (69゜00′S, 39゜35′E from February 2004 until January 2007. The BC concentration at Syowa Station ranged from below detection to 176 ng m^. Higher BC concentrations were observed frequently from April until October. Increase of BC concentration may be associated with poleward flow due to the approach of a cyclone and or blocking event during winter-spring. The BC-rich air masses traveled through the lower troposphere from the Atlantic and Indian Oceans to Syowa (Antarctic coast. During the summer (November-February, the BC concentration showed a diurnal variation together with surface wind speed and increased in the presence of katabatic wind from the Antarctic continent. Considering the low BC source strength over the Antarctic continent, the higher BC concentration in the continental air (katabatic wind might be caused by long range transport of BC via the free troposphere from mid- and low- latitudes. The seasonal variation of BC at Syowa Station had a maximum in July-September, while at the other coastal stations (Halley, Neumayer, and Ferraz and a continental station (Amundsen-Scott, the maximum occurred in October. This difference may result from different transport pathways, significant contribution of source regions and scavenging of BC by precipitation during the transport from the source regions. During the austral summer, long-range transport of BC via the free troposphere is likely to make an important contribution to the ambient BC concentration along the Antarctic coasts.

Macromolecular Crystallization in Microfluidics for the International Space Station

Science.gov (United States)

Monaco, Lisa A.; Spearing, Scott

2003-01-01

At NASA's Marshall Space Flight Center, the Iterative Biological Crystallization (IBC) project has begun development on scientific hardware for macromolecular crystallization on the International Space Station (ISS). Currently ISS crystallization research is limited to solution recipes that were prepared on the ground prior to launch. The proposed hardware will conduct solution mixing and dispensing on board the ISS, be fully automated, and have imaging functions via remote commanding from the ground. Utilizing microfluidic technology, IBC will allow for on orbit iterations. The microfluidics LabChip(R) devices that have been developed, along with Caliper Technologies, will greatly benefit researchers by allowing for precise fluid handling of nano/pico liter sized volumes. IBC will maximize the amount of science return by utilizing the microfluidic approach and be a valuable tool to structural biologists investigating medically relevant projects.

NRC/UBC fuelling station with intelligent compression

International Nuclear Information System (INIS)

Dada, A.; Boyd, B.; Law, L.; Semczyszyn, D.

2004-01-01

BOC Canada Ltd. will design, integrate and construct the second fueling station on the Hydrogen Highway. This station will be located at the National Research Council's Institute for Fuel Cell Innovation on the campus of the University of British Columbia. BOC's design will bring together an existing alkaline electrolyser, new compression, storage and dispensing. The station will be designed to serve fuel cell passenger vehicles using 350-bar storage. However, the flexible design concept will allow for many other user needs including the potential for servicing larger vehicles, as well as filling portable storage systems for use at satellite stations. The novel station design also offers the potential to fuel from multiple hydrogen sources. Together with NRC, this fueling station will be used to increase public, consumer and investor awareness of hydrogen technologies. Design and construction of this facility will assist in the development of industry codes and standards and familiarize authorities having jurisdiction with hydrogen fueling. The system concept offers the utmost attention to safety, novelty and flexibility. (author)

UV and vacuum-UV biological spectroscopy using synchrotron radiation

International Nuclear Information System (INIS)

Ito, Amando Siuiti

1996-01-01

Full text. Synchrotron radiation has been used as light source in the UV and VUV region for the study of many biological systems. In the time domain, measurements are made that allow the observation of dynamics and kinetics of biomolecules like proteins and peptides, using the fluorescent properties of either intrinsic or extrinsic probes. Optical activity of groups inside biomolecules allows the use of circular dichroism techniques to generate structural information and to follow processes like protein folding. Confocal scanning of synchrotron light generates microscopy resolution below 100 nm, allowing the creation of high quality three dimensional images of biological samples, and the collection of fluorescence originated from microvolumes inside the samples. We propose a station at LNLS for these three techniques: time-resolved fluorescence, circular dischroism and confocal microscopy, using UV and VUV light. (author)

Islands for nuclear power stations

International Nuclear Information System (INIS)

Usher, E.F.F.W.; Fraser, A.P.

1981-01-01

The safety principles, design criteria and types of artificial island for an offshore nuclear power station are discussed with particular reference to siting adjacent to an industrial island. The paper concludes that the engineering problems are soluble and that offshore nuclear power stations will eventually be built but that much fundamental work is still required. (author)

Medication-indication knowledge bases: a systematic review and critical appraisal.

Science.gov (United States)

Salmasian, Hojjat; Tran, Tran H; Chase, Herbert S; Friedman, Carol

2015-11-01

Medication-indication information is a key part of the information needed for providing decision support for and promoting appropriate use of medications. However, this information is not readily available to end users, and a lot of the resources only contain this information in unstructured form (free text). A number of public knowledge bases (KBs) containing structured medication-indication information have been developed over the years, but a direct comparison of these resources has not yet been conducted. We conducted a systematic review of the literature to identify all medication-indication KBs and critically appraised these resources in terms of their scope as well as their support for complex indication information. We identified 7 KBs containing medication-indication data. They notably differed from each other in terms of their scope, coverage for on- or off-label indications, source of information, and choice of terminologies for representing the knowledge. The majority of KBs had issues with granularity of the indications as well as with representing duration of therapy, primary choice of treatment, and comedications or comorbidities. This is the first study directly comparing public KBs of medication indications. We identified several gaps in the existing resources, which can motivate future research. © The Author 2015. Published by Oxford University Press on behalf of the American Medical Informatics Association. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

DESM: portal for microbial knowledge exploration systems

KAUST Repository

Salhi, Adil

2015-11-05

Microorganisms produce an enormous variety of chemical compounds. It is of general interest for microbiology and biotechnology researchers to have means to explore information about molecular and genetic basis of functioning of different microorganisms and their ability for bioproduction. To enable such exploration, we compiled 45 topic-specific knowledgebases (KBs) accessible through DESM portal (www.cbrc.kaust.edu.sa/desm). The KBs contain information derived through text-mining of PubMed information and complemented by information data-mined from various other resources (e.g. ChEBI, Entrez Gene, GO, KOBAS, KEGG, UniPathways, BioGrid). All PubMed records were indexed using 4 538 278 concepts from 29 dictionaries, with 1 638 986 records utilized in KBs. Concepts used are normalized whenever possible. Most of the KBs focus on a particular type of microbial activity, such as production of biocatalysts or nutraceuticals. Others are focused on specific categories of microorganisms, e.g. streptomyces or cyanobacteria. KBs are all structured in a uniform manner and have a standardized user interface. Information exploration is enabled through various searches. Users can explore statistically most significant concepts or pairs of concepts, generate hypotheses, create interactive networks of associated concepts and export results. We believe DESM will be a useful complement to the existing resources to benefit microbiology and biotechnology research.

Space station evolution: Planning for the future

Science.gov (United States)

Diaz, Alphonso V.; Askins, Barbara S.

1987-06-01

The need for permanently manned presence in space has been recognized by the United States and its international partners for many years. The development of this capability was delayed due to the concurrent recognition that reusable earth-to-orbit transportation was also needed and should be developed first. While the decision to go ahead with a permanently manned Space Station was on hold, requirements for the use of the Station were accumulating as ground-based research and the data from unmanned spacecraft sparked the imagination of both scientists and entrepreneurs. Thus, by the time of the Space Station implementation decision in the early 1980's, a variety of disciplines, with a variety of requirements, needed to be accommodated on one Space Station. Additional future requirements could be forecast for advanced missions that were still in the early planning stages. The logical response was the development of a multi-purpose Space Station with the ability to evolve on-orbit to new capabilities as required by user needs and national or international decisions, i.e., to build an evolutionary Space Station. Planning for evolution is conducted in parallel with the design and development of the baseline Space Station. Evolution planning is a strategic management process to facilitate change and protect future decisions. The objective is not to forecast the future, but to understand the future options and the implications of these on today's decisions. The major actions required now are: (1) the incorporation of evolution provisions (hooks and scars) in the baseline Space Station; and (2) the initiation of an evolution advanced development program.

Space station evolution: Planning for the future

Science.gov (United States)

Diaz, Alphonso V.; Askins, Barbara S.

1987-01-01

The need for permanently manned presence in space has been recognized by the United States and its international partners for many years. The development of this capability was delayed due to the concurrent recognition that reusable earth-to-orbit transportation was also needed and should be developed first. While the decision to go ahead with a permanently manned Space Station was on hold, requirements for the use of the Station were accumulating as ground-based research and the data from unmanned spacecraft sparked the imagination of both scientists and entrepreneurs. Thus, by the time of the Space Station implementation decision in the early 1980's, a variety of disciplines, with a variety of requirements, needed to be accommodated on one Space Station. Additional future requirements could be forecast for advanced missions that were still in the early planning stages. The logical response was the development of a multi-purpose Space Station with the ability to evolve on-orbit to new capabilities as required by user needs and national or international decisions, i.e., to build an evolutionary Space Station. Planning for evolution is conducted in parallel with the design and development of the baseline Space Station. Evolution planning is a strategic management process to facilitate change and protect future decisions. The objective is not to forecast the future, but to understand the future options and the implications of these on today's decisions. The major actions required now are: (1) the incorporation of evolution provisions (hooks and scars) in the baseline Space Station; and (2) the initiation of an evolution advanced development program.

Shippingport Station decommissioning project overview

International Nuclear Information System (INIS)

Schreiber, J.J.

1985-01-01

The U.S. Department of Energy is in the process of decommissioning the Shippingport Atomic Power Station located on the Ohio River, 30 miles northwest of Pittsburgh, Pennsylvania. The Shippingport Station is the first commercial size nuclear power plant to undergo decommissioning in the United Staes. The plant is located on approximately 7 acres of land owned by the Duquesne Light Company (DLC) and leased to the U.S. Government. DLC operates two nuclear power plants, Beaver Valley 1 and 2, located immediately adjacent to the site and the Bruce Mansfield coal-fired power plant is also within the immediate area. The Station was shutdown in October, 1982. Defueling operations began in 1983 and were completed by September, 1984. The Shippingport Station consists of a 275' x 60' fuel handling building containing the reactor containment chamber, the service building, the turbine building, the radioactive waste processing building, the administration building and other smaller support buildings. The Station has four coolant loops and most of the containment structures are located below grade. Structures owned by the U.S. Government including the fuel handling building, service building, contaminated equipment room, the boiler chambers, the radioactive waste processing building and the decontamination and laydown buildings will be dismantled and removed to 3 feet below grade. The area will then be filled with clean soil and graded. The turbine building, testing and training building and the administration building are owned by DLC and will remain

47 CFR 74.882 - Station identification.

Science.gov (United States)

2010-10-01

...'s call sign or designator, its location, and the call sign of the broadcasting station or name of... operation. Identification may be made by transmitting the station call sign by visual or aural means or by...

Environmental surveillance of PWR power stations

International Nuclear Information System (INIS)

Conti, M.

1980-01-01

The action of Electricite de France with respect to the environment of PWR nuclear power stations is essentially centred on prevention. Controls are carried out at two levels: - before the power station goes on stream (radioecological study), - when the power station is operational. The purpose of the controls effected on the radioactive effluents and the environment is to check that the maximum discharge rate stipulated in the corresponding orders is complied with and to ensure that there are no anomalies in the environment [fr

Environmental assessment, proposed generating station for Darlington

International Nuclear Information System (INIS)

1975-04-01

This document indicates the intention of Ontario Hydro to seek approval from the Provincial Government for its plan to construct and operate a 3400 MWe nuclear generating station at the Darlington site, west of Bowmanville. This preliminary proposal also contains the environmental assessment. The environmental section of this proposal describes and assesses the existing environment and the environmental influences which would occur due to the construction and operation of a nuclear generating station, consisting of four 850 MW units, at the Darlington site. This proposed station is similar to the Bruce GS A station presently under construction. (author)

47 CFR 73.1201 - Station identification.

Science.gov (United States)

2010-10-01

... public file. The notice must state that the station's public file is available for inspection and that consumers can view it at the station's main studio and on its Web site. At least one of the announcements...

Central station market development strategies for photovoltaics

Science.gov (United States)

1980-01-01

Federal market development strategies designed to accelerate the market penetration of central station applications of photovoltaic energy system are analyzed. Since no specific goals were set for the commercialization of central station applications, strategic principles are explored which, when coupled with specific objectives for central stations, can produce a market development implementation plan. The study includes (1) background information on the National Photovoltaic Program, photovoltaic technology, and central stations; (2) a brief market assessment; (3) a discussion of the viewpoints of the electric utility industry with respect to solar energy; (4) a discussion of commercialization issues; and (5) strategy principles. It is recommended that a set of specific goals and objectives be defined for the photovoltaic central station program, and that these goals and objectives evolve into an implementation plan that identifies the appropriate federal role.

Radiation safety of mobile phones and base stations; Matkapuhelimien ja tukiasemien saeteilyturvallisuus

Energy Technology Data Exchange (ETDEWEB)

Jokela, K.; Leszczynski, D.; Paile, W.; Salomaa, S.; Puranen, L.; Hyysalo, P.

1997-06-01

The recent expansion of personal telecommunications has led to a rapid increase in the exposure of people to the radio-frequency (RF) radiation. Although the mobile phones are low power devices, the antenna is so close to the head that the local exposure may slightly exceed 2 W/kg, the current exposure limit for the local specific absorption rate SAR for the general public. The increase in the temperature is, however, too small to have any physiological significance. On the basis of experiments with cell cultures it is possible that other biological effects caused by some unknown non-thermal mechanism exist, but thus far there is conclusive biological or epidemiological evidence to suggest any diseases adverse physiological changes below the thermal threshold. The use of a mobile phone by a person wearing a pace-maker, the immunity which against the electromagnetic interference from the mobile phone has not be assured, is not recommended. The exposure caused by the base stations is in almost all practical ceases all below the power density limits for general public. (orig.) (115 refs.).

HSIP Fire Stations in New Mexico

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — Fire Stations in New Mexico Any location where fire fighters are stationed or based out of, or where equipment that such personnel use in carrying out their jobs is...

76 FR 40754 - Duke Energy Carolinas, LLC Catawba Nuclear Station, Units 1 and 2; McGuire Nuclear Station, Units...

Science.gov (United States)

2011-07-11

... NUCLEAR REGULATORY COMMISSION [NRC-2011-0100; Docket Nos. 50-413 and 50-414; Docket Nos. 50-369 and 50-370; Docket Nos. 50-269, 50-270, And 50-287] Duke Energy Carolinas, LLC Catawba Nuclear Station, Units 1 and 2; McGuire Nuclear Station, Units 1 and 2; Oconee Nuclear Station, Units 1, 2, and 3; Notice...

Periodical inspection in nuclear power stations

International Nuclear Information System (INIS)

1986-01-01

Periodical inspection is presently being made of eight nuclear power plants in nuclear power stations. Up to the present time, in three of them, failures as follows have been observed. (1) Unit 3 (PWR) of the Mihama Power Station in The Kansai Electric Power Co., Inc. Nineteen heat-transfer tubes of the steam generators were plugged up due to failure. A fuel assembly with a failed spring fixture and in another the control-rod cluster with a failed control rod fixture were replaced. (2) Unit 2 (PWR) of the Oi Power Station in The Kansai Electric Power Co., Inc. Eight heat-transfer tubes of the heat exchangers were plugged up due to failure. (3) Unit 6 (BWR) of the Fukushima Nuclear Power Station I in The Tokyo Electric Power Co., Inc. A fuel assembly with leakage was replaced. (Mori, K.)

Microgravity research in plant biological systems: Realizing the potential of molecular biology

Science.gov (United States)

Lewis, Norman G.; Ryan, Clarence A.

1993-01-01

The sole all-pervasive feature of the environment that has helped shape, through evolution, all life on Earth is gravity. The near weightlessness of the Space Station Freedom space environment allows gravitational effects to be essentially uncoupled, thus providing an unprecedented opportunity to manipulate, systematically dissect, study, and exploit the role of gravity in the growth and development of all life forms. New and exciting opportunities are now available to utilize molecular biological and biochemical approaches to study the effects of microgravity on living organisms. By careful experimentation, we can determine how gravity perception occurs, how the resulting signals are produced and transduced, and how or if tissue-specific differences in gene expression occur. Microgravity research can provide unique new approaches to further our basic understanding of development and metabolic processes of cells and organisms, and to further the application of this new knowledge for the betterment of humankind.

Balloon launching station, Mildura, Victoria

International Nuclear Information System (INIS)

The Mildura Balloon Launching Station was established in 1960 by the Department of Supply (now the Department of Manufacturing Industry) on behalf of the United States Atomic Energy Commission (USAEC) to determine the content of radioactive material in the upper atmosphere over Australia. The Station location and layout, staffing, balloon launching equipment, launching, tracking and recovery are described. (R.L.)

Determination of production biology of Cladocera in a reservoir receiving hyperthermal effluents from a nuclear production reactor

International Nuclear Information System (INIS)

Vigerstad, T.J.

1980-01-01

The effects on zooplankton of residence in a cooling reservoir receiving hyperthermal effluents directly from a nuclear-production-reactor were examined. The design of the study was to compare rates of cladoceran population production at two stations in the winter and summer of 1976 on Par Pond, the cooling reservoir located on the Savannah River Plant, Aiken, SC. One station was located in an area of the reservoir directly receiving hyperthermal effluent (Station MAS), and the second was located about 4 km away in an area where surface temperatures were normal for reservoirs in the general geographical region (Station CAS). The statistical properties of the Edmondson egg ratio model (Edmondson, 1960) were examined to determine if it would be a suitable method for calculating cladoceran production rates for comparison between stations. Based on an examination of the variance associated with standing stock and fecundity measurements and other consideratios, the use of the egg ratio model was abandoned. Instead, a non-parametric comparison between stations of standing stock and fecundity data for Bosmina longirostris, taken for the egg ratio model, were used to observe potential hyperthermal effluent effects. There was a statistically higher incidence of deformed eggs in the Bosmina population at Station MAS in the summer. Bosmina standing stock underwent two large oscillations in the winter and three large oscillations in the summer at Station MAS compared with two in the winter and one in the summer at Station CAS. These results are consistent with almost all other Par Pond studies which have found the two stations to be essentially similar in species composition but with some statistically significant differences in various aspects of the biology of the species

Monitoring of nuclear power stations

International Nuclear Information System (INIS)

Ull, E.; Labudda, H.J.

1987-01-01

The purpose of the invention is to create a process for undelayed automated detection and monitoring of accidents in the operation of nuclear power stations. According to the invention, this problem is solved by the relevant local measurements, such as radiation dose, components and type of radiation and additional relevant meteorological parameters being collected by means of wellknown data collection platforms, these being transmitted via transmission channels by means of satellites to suitable worldwide situated receiving stations on the ground, being processed there and being evaluated to recognise accidents. The local data collection platforms are used in the immediate vicinity of the nuclear power station. The use of aircraft, ships and balloons as data collection systems is also intended. (HWJ)

How to handle station black outs

Energy Technology Data Exchange (ETDEWEB)

Reisch, Frigyes [Swedish Nuclear Power Inspectorate, S-10252 Stockholm (Sweden)

1986-02-15

Station black out is defined as the loss of ail high voltage alternating current at a nuclear power site. An international study was made to survey the practices in the different countries. The best way to handle station black out is to avoid it therefore briefly the normal off site and emergency on site power supplies are discussed. The ways in use to enhance nuclear power plants using Boiling Water Reactors or Pressurized Water Reactors to cope with a station black out are discussed in some detail. (author)

How to handle station black outs

International Nuclear Information System (INIS)

Reisch, Frigyes

1986-01-01

Station black out is defined as the loss of ail high voltage alternating current at a nuclear power site. An international study was made to survey the practices in the different countries. The best way to handle station black out is to avoid it therefore briefly the normal off site and emergency on site power supplies are discussed. The ways in use to enhance nuclear power plants using Boiling Water Reactors or Pressurized Water Reactors to cope with a station black out are discussed in some detail. (author)

Thermal ecological study on the water quality and biological impact assessment in the vicinity of Madras Atomic Power Station, Kalpakkam, India

International Nuclear Information System (INIS)

Shahul Hameed, P.; Syed Mohamed, H.E.; Krishnamoorthy, R.

2007-01-01

Madras Atomic Power Station (MAPS), Kalpakkam uses seawater as tertiary coolant at the rate of 35m3/sec employing a once through type of circuit. The discharged water travels as a canal and mixes with seawater at the mixing zone. The present study investigated the impact of the discharged thermal effluent on the physical chemical and biological quality of the receiving seawater body. Measurements of ΔT between Intake and Outfall ranged from 6.1 to 9.8 deg C and between Intake and Mixing zone from 3.2 to 6.0 deg C. These values are well within the legal limits. The thermal plume is shore attached and extended up to 300 m from the shore and registered a ΔT of 3-4 deg C. No measurable Change in the physical and chemical parameters of seawater (DO, Salinity NO 3 , NO 2 , NH 3 , PO 4 and SiO 3 ) in relation to thermal discharges was observed. However, these parameters fluctuated with seasonal changes. The shore attached thermal plume adversely affected the density and distribution of macro benthic animals. The benthos are absent in the mixing zone and their density decreased about 500 m on either side of the mixing zone. The natural shift in the mixing zone provides opportunities for the recolonization of macro benthos. The thermal tolerance study revealed that the experimental fish species Mugil cephalus and Alepeus djidapa did not show any mortality or loss of equilibrium at Δ5 degC (33 degC) and Δ T 7 degC (35 degC) and the maximum ΔT recorded at the impact area is 6 degC. The gradual increase in temperature as found in the plume favors the fishes to escape the acute thermal exposures. (author)

Mukilteo Research Station

Data.gov (United States)

Federal Laboratory Consortium — Research at the Mukilteo Research Station focuses on understanding the life cycle of marine species and the impacts of ecosystem stressors on anadromous and marine...

Project authorization process in the thermal power stations vs in the hydroelectric power stations: two weights, two measurements?

International Nuclear Information System (INIS)

Comtois, Y.

2004-01-01

Key topics include the long tendering process, a comparison of two projects: thermal station vs. hydroelectrical station, and the solutions towards reducing the delay in obtaining authorization. (author)

Reliability study of nuclear power stations

International Nuclear Information System (INIS)

Nemec, J.; Sedlacek, J.

1975-01-01

The paper considers the physical and mathematical bases underlying nuclear power station reliability from the standpoints of material fatigue, thermal yield and ageing. The risk of failure of nuclear power station components is determined by means of the Markov stochastic process

The influence of subway station design on noise levels.

Science.gov (United States)

Shah, Ravi R; Suen, Jonathan J; Cellum, Ilana P; Spitzer, Jaclyn B; Lalwani, Anil K

2017-05-01

To investigate the impact of subway station design on platform noise levels. Observational. Continuous A-weighted decibel (dBA) sound levels were recorded in 20 New York City subway stations, where trains entered on either a straight track or curved track in 10 stations each. Equivalent continuous noise levels (L eq ) at various locations on the boarding platform (inbound end, midplatform, and outbound end) during train entry and exit were compared between the straight and curved stations in broadband as well as narrow one-third octave bands. Overall, curved stations trended louder than straight stations, although the difference in broadband L eq did not reach statistical significance (curve, 83.4 dBA; straight, 82.6 dBA; P = .054). Noise levels were significantly louder at the inbound end of the platform during train entry (inbound, 89.7 dBA; mid, 85.5 dBA; outbound, 78.7 dBA; P < .001) and at the outbound end during train exit (inbound, 79.7 dBA; mid, 85.3 dBA; outbound, 89.1 dBA; P < .001). Narrow band analysis showed that curved stations were significantly louder than straight stations at 100 Hz and high frequencies from 8 to 20 kHz. Peak impact levels ranged from 104 to 121 dBA. Curved stations have a different noise profile compared to straight stations and are significantly louder than straight stations at high frequencies. Designing stations with straight tracks within the platform can help reduce commuter noise exposure. NA Laryngoscope, 127:1169-1174, 2017. © 2016 The American Laryngological, Rhinological and Otological Society, Inc.

Space Station power system issues

International Nuclear Information System (INIS)

Giudici, R.J.

1985-01-01

Issues governing the selection of power systems for long-term manned Space Stations intended solely for earth orbital missions are covered briefly, drawing on trade study results from both in-house and contracted studies that have been conducted over nearly two decades. An involvement, from the Program Development Office at MSFC, with current Space Station concepts began in late 1982 with the NASA-wide Systems Definition Working Group and continued throughout 1984 in support of various planning activities. The premise for this discussion is that, within the confines of the current Space Station concept, there is good reason to consider photovoltaic power systems to be a venerable technology option for both the initial 75 kW and 300 kW (or much greater) growth stations. The issue of large physical size required by photovoltaic power systems is presented considering mass, atmospheric drag, launch packaging and power transmission voltage as being possible practicality limitations. The validity of searching for a cross-over point necessitating the introduction of solar thermal or nuclear power system options as enabling technologies is considered with reference to programs ranging from the 4.8 kW Skylab to the 9.5 gW Space Power Satellite

Research on station management in subway operation safety

Science.gov (United States)

Li, Yiman

2017-10-01

The management of subway station is an important part of the safe operation of urban subway. In order to ensure the safety of subway operation, it is necessary to study the relevant factors that affect station management. In the protection of subway safety operations on the basis of improving the quality of service, to promote the sustained and healthy development of subway stations. This paper discusses the influencing factors of subway operation accident and station management, and analyzes the specific contents of station management security for subway operation, and develops effective suppression measures. It is desirable to improve the operational quality and safety factor for subway operations.

Materials Test Station

Data.gov (United States)

Federal Laboratory Consortium — When completed, the Materials Test Station at the Los Alamos Neutron Science Center will meet mission need. MTS will provide the only fast-reactor-like irradiation...

Routes and Stations

Data.gov (United States)

Department of Homeland Security — he Routes_Stations table is composed of fixed rail transit systems within the Continental United States, Alaska, Hawaii, the District of Columbia, and Puerto Rico....

Public Transit Stations

Data.gov (United States)

Department of Homeland Security — fixed rail transit stations within the Continental United States, Alaska, Hawaii, the District of Columbia, and Puerto Rico. The modes of transit that are serviced...

Maine Field Station

Data.gov (United States)

Federal Laboratory Consortium — In 2000 NOAA's National Marine Fisheries Service established the Maine Field Station in Orono, ME to have more direct involvement in the conservation of the living...

USRCRN Station Information

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Documentation of United States Regional Climate Reference Network (USRCRN) installations in 2009. Installations documented are for USRCRN pilot project stations in...

Space Biology in Russia Today

Science.gov (United States)

Grigoriev, Anatoly; Sychev, Vladimir; Ilyin, Eugene

At present space biology research in Russia is making significant progress in several areas of high priority. Gravitational biology. In April-May 2013, a successful 30-day flight of the biological satellite (biosatellite) Bion-M1 was conducted, which carried rodents (mice and gerbils), geckos, fish, mollusks, crustaceans, microorganisms, insects, lower and higher plants, seeds, etc. The investigations were performed by Russian scientists as well as by researchers from NASA, CNES, DLR and South Korea. Foton-M4 carrying various biological specimens is scheduled to launch in 2014. Work has begun to develop science research programs to be implemented onboard Bion-M2 and Bion-M3 as well as on high apogee recoverable spacecraft. Study of the effects of microgravity on the growth and development of higher plants cultivated over several generations on the International Space Station (ISS) has been recently completed. Space radiobiology. Regular experiments aimed at investigating the effects of high-energy galactic cosmic rays on the animal central nervous system and behavior are being carried out using the Particle Accelerator in the town of Dubna. Biological (environmental) life support systems. In recent years, experiments have been performed on the ISS to upgrade technologies of plant cultivation in microgravity. Advanced greenhouse mockups have been built and are currentlyundergoing bioengineering tests. Technologies of waste utilization in space are being developed. Astrobiology experiments in orbital missions. In 2010, the Biorisk experiment on bacterial and fungal spores, seeds and dormant forms of organisms was completed. The payload containing the specimens was installed on the exterior wall of the ISS and was exposed to outer space for 31 months. In addition, Bion-M1 also carried seeds, bacterial spores and microbes that were exposed to outer space effects. The survival rate of bacterial spores incorporated into man-made meteorites, that were attached to the

Battery charging stations

Energy Technology Data Exchange (ETDEWEB)

Bergey, M.

1997-12-01

This paper discusses the concept of battery charging stations (BCSs), designed to service rural owners of battery power sources. Many such power sources now are transported to urban areas for recharging. A BCS provides the opportunity to locate these facilities closer to the user, is often powered by renewable sources, or hybrid systems, takes advantage of economies of scale, and has the potential to provide lower cost of service, better service, and better cost recovery than other rural electrification programs. Typical systems discussed can service 200 to 1200 people, and consist of stations powered by photovoltaics, wind/PV, wind/diesel, or diesel only. Examples of installed systems are presented, followed by cost figures, economic analysis, and typical system design and performance numbers.

Cerebral ketone body metabolism.

Science.gov (United States)

Morris, A A M

2005-01-01

Ketone bodies (KBs) are an important source of energy for the brain. During the neonatal period, they are also precursors for the synthesis of lipids (especially cholesterol) and amino acids. The rate of cerebral KB metabolism depends primarily on the concentration in blood; high concentrations occur during fasting and on a high-fat diet. Cerebral KB metabolism is also regulated by the permeability of the blood-brain barrier (BBB), which depends on the abundance of monocarboxylic acid transporters (MCT1). The BBB's permeability to KBs increases with fasting in humans. In rats, permeability increases during the suckling period, but human neonates have not been studied. Monocarboxylic acid transporters are also present in the plasma membranes of neurons and glia but their role in regulating KB metabolism is uncertain. Finally, the rate of cerebral KB metabolism depends on the activities of the relevant enzymes in brain. The activities vary with age in rats, but reliable results are not available for humans. Cerebral KB metabolism in humans differs from that in the rat in several respects. During fasting, for example, KBs supply more of the brain's energy in humans than in the rat. Conversely, KBs are probably used more extensively in the brain of suckling rats than in human neonates. These differences complicate the interpretation of rodent studies. Most patients with inborn errors of ketogenesis develop normally, suggesting that the only essential role for KBs is as an alternative fuel during illness or prolonged fasting. On the other hand, in HMG-CoA lyase deficiency, imaging generally shows asymptomatic white-matter abnormalities. The ability of KBs to act as an alternative fuel explains the effectiveness of the ketogenic diet in GLUT1 deficiency, but its effectiveness in epilepsy remains unexplained.

Roles and regulation of ketogenesis in cultured astroglia and neurons under hypoxia and hypoglycemia.

Science.gov (United States)

Takahashi, Shinichi; Iizumi, Takuya; Mashima, Kyoko; Abe, Takato; Suzuki, Norihiro

2014-09-11

Exogenous ketone bodies (KBs), acetoacetate (AA), and β-hydroxybutyrate (BHB) act as alternative energy substrates in neural cells under starvation. The present study examined the endogenous ketogenic capacity of astroglia under hypoxia with/without glucose and the possible roles of KBs in neuronal energy metabolism. Cultured neurons and astroglia were prepared from Sprague-Dawley rats. Palmitic acid (PAL) and l-carnitine (LC) were added to the assay medium. The 4- to 24-hr production of AA and BHB was measured using the cyclic thio-NADH method. (14)C-labeled acid-soluble products (KBs) and (14)CO2 produced from [1-(14)C]PAL were also measured. l-[U-(14)C]lactic acid ([(14)C]LAC), [1-(14)C]pyruvic acid ([(14)C]PYR), or β-[1-(14)C]hydroxybutyric acid ([(14)C]BHB) was used to compare the oxidative metabolism of the glycolysis end products with that of the KBs. Some cells were placed in a hypoxic chamber (1% O2). PAL and LC induced a higher production of KBs in astroglia than in neurons, while the CO2 production from PAL was less than 5% of the KB production in both astroglia and neurons. KB production in astroglia was augmented by the AMP-activated protein kinase activators, AICAR and metformin, as well as hypoxia with/without glucose. Neuronal KB production increased under hypoxia in the absence of PAL and LC. In neurons, [(14)C]LAC and [(14)C]PYR oxidation decreased after 24 hr of hypoxia, while [(14)C]BHB oxidation was preserved. Astroglia responds to ischemia in vitro by enhancing KB production, and astroglia-produced KBs derived from fatty acid might serve as a neuronal energy substrate for the tricarboxylic acid cycle instead of lactate, as pyruvate dehydrogenase is susceptible to ischemia. © The Author(s) 2014 Reprints and permissions: sagepub.com/journalsPermissions.nav.

Space Station data management system architecture

Science.gov (United States)

Mallary, William E.; Whitelaw, Virginia A.

1987-01-01

Within the Space Station program, the Data Management System (DMS) functions in a dual role. First, it provides the hardware resources and software services which support the data processing, data communications, and data storage functions of the onboard subsystems and payloads. Second, it functions as an integrating entity which provides a common operating environment and human-machine interface for the operation and control of the orbiting Space Station systems and payloads by both the crew and the ground operators. This paper discusses the evolution and derivation of the requirements and issues which have had significant effect on the design of the Space Station DMS, describes the DMS components and services which support system and payload operations, and presents the current architectural view of the system as it exists in October 1986; one-and-a-half years into the Space Station Phase B Definition and Preliminary Design Study.

Klüver-Bucy syndrome associated with a recessive variant in HGSNAT in two siblings with Mucopolysaccharidosis type IIIC (Sanfilippo C).

Science.gov (United States)

Hu, Hao; Hübner, Christoph; Lukacs, Zoltan; Musante, Luciana; Gill, Esther; Wienker, Thomas F; Ropers, Hans-Hilger; Knierim, Ellen; Schuelke, Markus

2017-02-01

Klüver-Bucy syndrome (KBS) comprises a set of neurobehavioral symptoms with psychic blindness, hypersexuality, disinhibition, hyperorality, and hypermetamorphosis that were originally observed after bilateral lobectomy in Rhesus monkeys. We investigated two siblings with KBS from a consanguineous family by whole-exome sequencing and autozygosity mapping. We detected a homozygous variant in the heparan-α-glucosaminidase-N-acetyltransferase gene (HGSNAT; c.518G>A, p.(G173D), NCBI ClinVar RCV000239404.1), which segregated with the phenotype. Disease-causing variants in this gene are known to be associated with autosomal recessive Mucopolysaccharidosis type IIIC (MPSIIIC, Sanfilippo C). This lysosomal storage disease is due to deficiency of the acetyl-CoA:α-glucosaminidase-N-acetyltransferase, which was shown to be reduced in patient fibroblasts. Our report extends the phenotype associated with MPSIIIC. Besides MPSIIIA and MPSIIIB, due to variants in SGSH and NAGLU, this is the third subtype of Sanfilippo disease to be associated with KBS. MPSIII should be included in the differential diagnosis of young patients with KBS.

Klüver–Bucy syndrome associated with a recessive variant in HGSNAT in two siblings with Mucopolysaccharidosis type IIIC (Sanfilippo C)

Science.gov (United States)

Hu, Hao; Hübner, Christoph; Lukacs, Zoltan; Musante, Luciana; Gill, Esther; Wienker, Thomas F; Ropers, Hans-Hilger; Knierim, Ellen; Schuelke, Markus

2017-01-01

Klüver–Bucy syndrome (KBS) comprises a set of neurobehavioral symptoms with psychic blindness, hypersexuality, disinhibition, hyperorality, and hypermetamorphosis that were originally observed after bilateral lobectomy in Rhesus monkeys. We investigated two siblings with KBS from a consanguineous family by whole-exome sequencing and autozygosity mapping. We detected a homozygous variant in the heparan-α-glucosaminidase-N-acetyltransferase gene (HGSNAT; c.518G>A, p.(G173D), NCBI ClinVar RCV000239404.1), which segregated with the phenotype. Disease-causing variants in this gene are known to be associated with autosomal recessive Mucopolysaccharidosis type IIIC (MPSIIIC, Sanfilippo C). This lysosomal storage disease is due to deficiency of the acetyl-CoA:α-glucosaminidase-N-acetyltransferase, which was shown to be reduced in patient fibroblasts. Our report extends the phenotype associated with MPSIIIC. Besides MPSIIIA and MPSIIIB, due to variants in SGSH and NAGLU, this is the third subtype of Sanfilippo disease to be associated with KBS. MPSIII should be included in the differential diagnosis of young patients with KBS. PMID:27827379

Darlington Station outage - a maintenance perspective

International Nuclear Information System (INIS)

Plourde, J.; Marczak, J.; Stone, M.; Myers, R.; Sutton, K.

1997-01-01

Ontario Hydro's Darlington Nuclear Generating Station (4x881MW(e)net) has carried out its first station outage since full commercial operation. The outage presented challenges to the organization in terms of outage planning, support, management, and safe execution within the constraints of schedule, budget and resources. This paper will focus on the success of the outage maintenance program, identifying the major work programs - a vacuum structure and containment outage, an emergency service water system outage, an emergency coolant injection system outage, intake channel inspections, low pressure service water inspections, and significant outage maintenance work on each of the four reactor units. Planning for the outage was initiated early in anticipation of this important milestone in the station's life. Detailed safety reviews - nuclear, radiation, and conventional - were conducted in support of the planned maintenance program. System lineup and work protection were provided by the Station Operator work group. Work protection permitry was initiated well in advance of the outage. Station maintenance staff resources were bolstered in support of the outage to ensure program execution could be maintained within the schedule. Training programs were in place to ensure that expectations were clear and that high standards would be maintained. Materials management issues in support of maintenance activities were given high priority to ensure no delays to the planned work. Station management review and monitoring in preparation for and during the outage ensured that staff priorities remained focused. Lessons learned from the outage execution are being formalized in maintenance procedures and outage management procedures, and shared with the nuclear community. (author)

The Grossmatt hydro-power station

International Nuclear Information System (INIS)

Hintermann, M.

2006-01-01

This final report for the Swiss Federal Office of Energy (SFOE) presents the project for a small hydropower station on the Birs river in north-western Switzerland. The report reviews the history of the project, in which a new 385 kW-hydro-power station at the site of an earlier installation is foreseen. Details are presented on the investigations made and on the co-ordination with the owners of the hydro-power station situated up-river, the local power utility and the local authorities. Also, the requirements placed on the project by the fishing authorities are quoted and the solution foreseen is described. Also discussed are the requirements placed on the project by legislation on environmental impact and flood protection. Figures on electrical energy production and building costs are presented

The Paks Nuclear Power Station

International Nuclear Information System (INIS)

Erdosi, N.; Szabo, L.

1978-01-01

As the first stage in the construction of the Paks Nuclear Power Station, two units of 440 MW(e) each will be built. They are operated with two coolant loops each. The reactor units are VVER 440 type water-moderated PWR type heterogeneous power reactors designed in the Soviet Union and manufactured in Czechoslovakia. Each unit operates two Soviet-made K-220-44 steam turbines and Hungarian-made generators of an effective output of 220 MW. The output of the transformer units - also of Hungarian made - is 270 MVA. The radiation protection system of the nuclear power station is described. Protection against system failures is accomplished by specially designed equipment and security measures especially within the primary circuit. Some data on the power station under construction are given. (R.P.)

A Knowledge-based System for the Analysis of the Ability of Paying back Loans

Institute of Scientific and Technical Information of China (English)

朱明; 杨保安

2001-01-01

This paper describes the development of a knowledgebased system (KBS) for determining whether or not, and under what conditions, a bank Ioan officer should grant a business loan to a company. The prototype system developed focuses on what is bank loans risks management, how to prevent risk by the analysis of the ability of paying back loans. The paper makes the structural analysis involved in the system's decision situation, the structured situation diagram or model, dependency diagram and the document needed by the KBS prototype system thus are developed. Through testing the samples from loan business, the quality for the analysis of the ability of paying back loans can be effectively evaluated by the KBS prototype system.

75 FR 22674 - Moynihan Station Development Project

Science.gov (United States)

2010-04-29

... DEPARTMENT OF TRANSPORTATION Federal Railroad Administration Moynihan Station Development Project... availability of and public comment period for the Moynihan Station Development Project Environmental Assessment... 22675

The biological assessment of flora and fauna as standards for changes in the near-shore ocean environment: a study of Barbers Point Harbor.

Science.gov (United States)

Hokama, Y; Wachi, K M; Shiraki, A; Goo, C; Ebesu, J S

2001-02-01

The biological assessments of the flora and fauna in the near-shore ocean environment, specifically Barbers Point Harbor (BPH), demonstrate the usefulness of these biological analyses for evaluation of the changes occurring following man-made excavation for expansion of the harbor. The study included identification and enumeration of macroalgae and dinoflagellates and analyses of herbivores and carnivores in four areas within the perimeter of the harbor and the north and south entrances into the harbor. Numbers of macroalgae varied between 1994 and 1999 surveys, with significant decrease in numbers in stations C, D and E. Stations A and B were similar between 1994 and 1999 with a slight increase in 1999. The significant differences were shown with the appearance of Gambierdiscus toxicus (G toxicus) in 1999 among the algae in stations A and B. Assessment of herbivores and carnivores with the immunological membrane immunobead assay using monoclonal antibody to ciguatoxin and related polyethers demonstrated an increase in fish toxicity among the herbivore from 1994-1999 (22% increase) with a decrease (22%) in non-toxic fish. This was also demonstrated in the carnivores, but to a lesser degree. It is suggested that the biological analyses of the flora and the fauna of the near-shore ocean environment are appropriate to assess the changes that occur from natural and man-made alterations.

47 CFR 25.206 - Station identification.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Station identification. 25.206 Section 25.206 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS... identification is waived for all radio stations licensed under this part with the exception of satellite uplinks...

Error management process for power stations

International Nuclear Information System (INIS)

Hirotsu, Yuko; Takeda, Daisuke; Fujimoto, Junzo; Nagasaka, Akihiko

2016-01-01

The purpose of this study is to establish 'error management process for power stations' for systematizing activities for human error prevention and for festering continuous improvement of these activities. The following are proposed by deriving concepts concerning error management process from existing knowledge and realizing them through application and evaluation of their effectiveness at a power station: an entire picture of error management process that facilitate four functions requisite for maraging human error prevention effectively (1. systematizing human error prevention tools, 2. identifying problems based on incident reports and taking corrective actions, 3. identifying good practices and potential problems for taking proactive measures, 4. prioritizeng human error prevention tools based on identified problems); detail steps for each activity (i.e. developing an annual plan for human error prevention, reporting and analyzing incidents and near misses) based on a model of human error causation; procedures and example of items for identifying gaps between current and desired levels of executions and outputs of each activity; stages for introducing and establishing the above proposed error management process into a power station. By giving shape to above proposals at a power station, systematization and continuous improvement of activities for human error prevention in line with the actual situation of the power station can be expected. (author)

Regional travel-time residual studies and station correction from 1-D velocity models for some stations around Peninsular Malaysia and Singapore

Science.gov (United States)

Osagie, Abel U.; Nawawi, Mohd.; Khalil, Amin Esmail; Abdullah, Khiruddin

2017-06-01

We have investigated the average P-wave travel-time residuals for some stations around Southern Thailand, Peninsular Malaysia and Singapore at regional distances. Six years (January, 2010-December, 2015) record of events from central and northern Sumatra was obtained from the digital seismic archives of Integrated Research Institute for Seismology (IRIS). The criteria used for the data selection are designed to be above the magnitude of mb 4.5, depth less than 200 km and an epicentral distance shorter than 1000 km. Within this window a total number of 152 earthquakes were obtained. Furthermore, data were filtered based on the clarity of the seismic phases that are manually picked. A total of 1088 P-wave arrivals and 962 S-wave arrivals were hand-picked from 10 seismic stations around the Peninsula. Three stations IPM, KUM, and KOM from Peninsular Malaysia, four stations BTDF, NTU, BESC and KAPK from Singapore and three stations SURA, SRIT and SKLT located in the southern part of Thailand are used. Station NTU was chosen as the Ref. station because it recorded the large number of events. Travel-times were calculated using three 1-D models (Preliminary Ref. Earth Model PREM (Dziewonski and Anderson, 1981, IASP91, and Lienert et al., 1986) and an adopted two-point ray tracing algorithm. For the three models, we corroborate our calculated travel-times with the results from the use of TAUP travel-time calculation software. Relative to station NTU, our results show that the average P wave travel-time residual for PREM model ranges from -0.16 to 0.45 s for BESC and IPM respectively. For IASP91 model, the average residual ranges from -0.25 to 0.24 s for SRIT and SKLT respectively, and ranges from -0.22 to 0.30 s for KAPK and IPM respectively for Lienert et al. (1986) model. Generally, most stations have slightly positive residuals relative to station NTU. These corrections reflect the difference between actual and estimated model velocities along ray paths to stations and

Light Microscopy Module: International Space Station Premier Automated Microscope

Science.gov (United States)

Sicker, Ronald J.; Foster, William M.; Motil, Brian J.; Meyer, William V.; Chiaramonte, Francis P.; Abbott-Hearn, Amber; Atherton, Arthur; Beltram, Alexander; Bodzioney, Christopher; Brinkman, John;

A molecular epidemiological study of methicillin-resistant Staphylococci environmental contamination in railway stations and coach stations in Guangzhou of China.

Science.gov (United States)

Lin, J L; Peng, Y; Ou, Q T; Lin, D X; Li, Y; Ye, X H; Zhou, J L; Yao, Z J

2017-02-01

Methicillin-resistant Staphylococcus aureus (MRSA) has caused a series of public health problems since it was first found in 1961. However, there are few research studies on the MRSA environmental contamination in railway stations and coach stations. Therefore, the aim of this study was to determine MRSA environmental contamination in public transport stations. Between December 2013 and January 2014, 380 surface samples from three railway stations (180) and four coach stations (200) in Guangzhou were collected to isolate and determine the prevalence and characteristics of Staphylococci strains. 39·21% of all samples were Staphylococci isolates, 1·58% of Staphylococci isolates were MRSA isolates, and 6·05% were methicillin-susceptible S. aureus. The proportion of multidrug resistant among 149 Staphylococci isolates was 75·84%. None of MRSA isolates was identified with the Panton-Valentine Leukocidin (PVL) genes, and one of them was identified with the qac gene. Four MRSA isolates were Staphylococcal Cassette Chromosome mec IVa, and the other two were nontypeable. Staphylococcus aureus isolates were classified into several sequence types (STs), and STs showed possible cross-transmissions of isolates from various sources. Methicillin-resistant Staphylococci contamination prevalence was high, and the environment of stations may be the vectors transmitting the Staphylococci to passengers. This is the first study to comprehensively report the prevalence, antibiotic resistance, and molecular characteristics of contamination of Staphylococci isolates in railway stations and coach stations of China. It will have great public health implications on infection control in community settings because of the serious hazard of Staphylococci, especially methicillin-resistant Staphylococci. Our findings have provided evidence for relevant departments to reduce the contamination of Staphylococci in environment of public transport stations. © 2016 The Society for Applied

NASA space station automation: AI-based technology review

Science.gov (United States)

Firschein, O.; Georgeff, M. P.; Park, W.; Neumann, P.; Kautz, W. H.; Levitt, K. N.; Rom, R. J.; Poggio, A. A.

1985-01-01

Research and Development projects in automation for the Space Station are discussed. Artificial Intelligence (AI) based automation technologies are planned to enhance crew safety through reduced need for EVA, increase crew productivity through the reduction of routine operations, increase space station autonomy, and augment space station capability through the use of teleoperation and robotics. AI technology will also be developed for the servicing of satellites at the Space Station, system monitoring and diagnosis, space manufacturing, and the assembly of large space structures.

Space stations systems and utilization

CERN Document Server

Messerschmid, Ernst

1999-01-01

The design of space stations like the recently launched ISS is a highly complex and interdisciplinary task. This book describes component technologies, system integration, and the potential usage of space stations in general and of the ISS in particular. It so adresses students and engineers in space technology. Ernst Messerschmid holds the chair of space systems at the University of Stuttgart and was one of the first German astronauts.

Space Station Freedom operations costs

Science.gov (United States)

Accola, Anne L.; Williams, Gregory J.

1988-01-01

Measures to reduce the operation costs of the Space Station which can be implemented in the design and development stages are discussed. Operational functions are described in the context of an overall operations concept. The provisions for operations cost responsibilities among the partners in the Space Station program are presented. Cost estimating methodologies and the way in which operations costs affect the design and development process are examined.

VICKEY: Mining Conditional Keys on Knowledge Bases

DEFF Research Database (Denmark)

Symeonidou, Danai; Prado, Luis Antonio Galarraga Del; Pernelle, Nathalie

2017-01-01

A conditional key is a key constraint that is valid in only a part of the data. In this paper, we show how such keys can be mined automatically on large knowledge bases (KBs). For this, we combine techniques from key mining with techniques from rule mining. We show that our method can scale to KBs...

The Role of Knowledge Brokers: Lessons from a Community Based Research Study of Cultural Safety in Relation to People Who Use Drugs

Science.gov (United States)

McCall, Jane; Mollison, Ashley; Browne, Annette; Parker, Joanne; Pauly, Bernie

2017-01-01

The study explored cultural safety as a strategy to address the stigma of substance use in acute care settings. Two research team members took on the role of knowledge brokers (KBs) in order to liaise between the research team and two distinct research advisory groups: one with people who use drugs and the other nurses. The KBs were instrumental…

Using knowledge brokers to facilitate the uptake of pediatric measurement tools into clinical practice: a before-after intervention study

Directory of Open Access Journals (Sweden)

Cameron Dianne

2010-11-01

Full Text Available Abstract Background The use of measurement tools is an essential part of good evidence-based practice; however, physiotherapists (PTs are not always confident when selecting, administering, and interpreting these tools. The purpose of this study was to evaluate the impact of a multifaceted knowledge translation intervention, using PTs as knowledge brokers (KBs to facilitate the use in clinical practice of four evidence-based measurement tools designed to evaluate and understand motor function in children with cerebral palsy (CP. The KB model evaluated in this study was designed to overcome many of the barriers to research transfer identified in the literature. Methods A mixed methods before-after study design was used to evaluate the impact of a six-month KB intervention by 25 KBs on 122 practicing PTs' self-reported knowledge and use of the measurement tools in 28 children's rehabilitation organizations in two regions of Canada. The model was that of PT KBs situated in clinical sites supported by a network of KBs and the research team through a broker to the KBs. Modest financial remuneration to the organizations for the KB time (two hours/week for six months, ongoing resource materials, and personal and intranet support was provided to the KBs. Survey data were collected by questionnaire prior to, immediately following the intervention (six months, and at 12 and 18 months. A mixed effects multinomial logistic regression was used to examine the impact of the intervention over time and by region. The impact of organizational factors was also explored. Results PTs' self-reported knowledge of all four measurement tools increased significantly over the six-month intervention, and reported use of three of the four measurement tools also increased. Changes were sustained 12 months later. Organizational culture for research and supervisor expectations were significantly associated with uptake of only one of the four measurement tools. Conclusions KBs

Using knowledge brokers to facilitate the uptake of pediatric measurement tools into clinical practice: a before-after intervention study.

Science.gov (United States)

Russell, Dianne J; Rivard, Lisa M; Walter, Stephen D; Rosenbaum, Peter L; Roxborough, Lori; Cameron, Dianne; Darrah, Johanna; Bartlett, Doreen J; Hanna, Steven E; Avery, Lisa M

2010-11-23

The use of measurement tools is an essential part of good evidence-based practice; however, physiotherapists (PTs) are not always confident when selecting, administering, and interpreting these tools. The purpose of this study was to evaluate the impact of a multifaceted knowledge translation intervention, using PTs as knowledge brokers (KBs) to facilitate the use in clinical practice of four evidence-based measurement tools designed to evaluate and understand motor function in children with cerebral palsy (CP). The KB model evaluated in this study was designed to overcome many of the barriers to research transfer identified in the literature. A mixed methods before-after study design was used to evaluate the impact of a six-month KB intervention by 25 KBs on 122 practicing PTs' self-reported knowledge and use of the measurement tools in 28 children's rehabilitation organizations in two regions of Canada. The model was that of PT KBs situated in clinical sites supported by a network of KBs and the research team through a broker to the KBs. Modest financial remuneration to the organizations for the KB time (two hours/week for six months), ongoing resource materials, and personal and intranet support was provided to the KBs. Survey data were collected by questionnaire prior to, immediately following the intervention (six months), and at 12 and 18 months. A mixed effects multinomial logistic regression was used to examine the impact of the intervention over time and by region. The impact of organizational factors was also explored. PTs' self-reported knowledge of all four measurement tools increased significantly over the six-month intervention, and reported use of three of the four measurement tools also increased. Changes were sustained 12 months later. Organizational culture for research and supervisor expectations were significantly associated with uptake of only one of the four measurement tools. KBs positively influenced PTs' self-reported knowledge and self

47 CFR 74.601 - Classes of TV broadcast auxiliary stations.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Classes of TV broadcast auxiliary stations. 74... Television Broadcast Auxiliary Stations § 74.601 Classes of TV broadcast auxiliary stations. (a) TV pickup stations. A land mobile station used for the transmission of TV program material and related communications...

47 CFR 80.469 - Maritime mobile repeater stations in Alaska.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Maritime mobile repeater stations in Alaska. 80... RADIO SERVICES STATIONS IN THE MARITIME SERVICES Public Coast Stations Use of Telephony § 80.469 Maritime mobile repeater stations in Alaska. (a) Maritime mobile repeater stations are authorized to extend...

47 CFR 2.107 - Radio astronomy station notification.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Radio astronomy station notification. 2.107....107 Radio astronomy station notification. (a) Pursuant to No. 1492 of Article 13 and Section F of Appendix 3 to the international Radio Regulations (Geneva, 1982), operators of radio astronomy stations...

"Central Station" Londonis

Index Scriptorium Estoniae

2000-01-01

Londoni galeriis Milch seitsme läti, leedu ja eesti kunstniku projekt "Central Station". Kuraatorid Lisa Panting, Sally Tallant. Eestist osalevad Hanno Soans (Catarina Campinoga koostöös valminud video), Kiwa, Kai Kaljo

Time-slicing subsystem of the biology small-angle x-ray scattering station at the National Synchrotron Light Source

International Nuclear Information System (INIS)

Stubblefield, F.W.

1985-11-01

The time-slicing subsystem of the Biology Small-Angle X-ray Scattering divides the time period during which the data for small-angle x-ray diffraction patterns from biological samples is collected into time slices (or frames). The subsystem, being part of a multiprocessor experiment control and data acquisition system, has its own dedicated processor; it also has special-purpose front-end electronics sufficient to generate the gating and other control signals required to produce a sequence of as many as 256 time slices, measured with a basic time unit of 1 μsec. The electronics also synchronizes with execution of the time slice sequence the application of stimuli to the biological sample, the measurement of voltages generated by the sample, and the application of auxiliary device trigger pulses and routes detector data and auxiliary scaler data into appropriate time-slice-indexed buffers in a large external data memory array. The structure of the entire experiment control and data acquisition system is briefly reviewed. Details of the structure and operation of the time slice subsystem are presented. 7 refs., 5 figs

Space Station Habitability Research

Science.gov (United States)

Clearwater, Yvonne A.

1988-01-01

The purpose and scope of the Habitability Research Group within the Space Human Factors Office at the NASA/Ames Research Center is described. Both near-term and long-term research objectives in the space human factors program pertaining to the U.S. manned Space Station are introduced. The concept of habitability and its relevancy to the U.S. space program is defined within a historical context. The relationship of habitability research to the optimization of environmental and operational determinants of productivity is discussed. Ongoing habitability research efforts pertaining to living and working on the Space Station are described.

PERSPECTIVES FOR DEVELOPMENT OF THE BIOLOGIC PLUM PRODUCTION IN BULGARIA

Directory of Open Access Journals (Sweden)

Ivanka Vitanova

2014-03-01

Full Text Available The Bulgarian plum cultivars Gabrovska, Nevena, Strinava, Guliaeva and Balvanska slava, breeding in the Plum Experimental Station in the town of Dryanovo and the introduced cultivars Stanley, Chachanska lepotitsa, Opal, Malvazinka, Hramova renkloda, Tuleu timpuriu, Althan’s Gage, Pacific, Mirabell de Nancy, Anna Schpet and Jojo, what are high productive and are tolerant to sharka and other important economic plum diseases are suitable for the biologic plum production. The organic fertilization is a basic element of the technology for the biologic plum production. The fertilization with manure and the green manure with a winter green peas and with a peas-rye mix increased the humus content, influenced positive action on the supplying of the plum plants with the main nutrient macro elements, increased the yield and to be able apply successfully in the plum orchards and at not irrigation conditions.

20 CFR 1001.142 - Stationing of DVOP staff.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Stationing of DVOP staff. 1001.142 Section 1001.142 Employees' Benefits OFFICE OF THE ASSISTANT SECRETARY FOR VETERANS' EMPLOYMENT AND TRAINING... Veterans Outreach Program (DVOP) § 1001.142 Stationing of DVOP staff. DVOP specialists shall be stationed...

47 CFR 32.2311 - Station apparatus.

Science.gov (United States)

2010-10-01

... FOR TELECOMMUNICATIONS COMPANIES Instructions for Balance Sheet Accounts § 32.2311 Station apparatus... company shall prepare a list of station apparatus which shall be used as its list of disposition units for... technicians, and others, shall be included in Account 2114, Tools and other work equipment, Account 2220...

S. Pellegrino and Brasimone seismic stations

International Nuclear Information System (INIS)

Capocecera, P.; Tedeschi, E.; Vitiello, F.

1988-07-01

The paper describes the technical features relative to the S. Pellegrino and Brasimone seismic stations. The stations have been modified in order to realize a central data acquisition system; in this way seismic signals are sent to Brasimone Center through telephone pair and are recorded in continuous form. (author)

49 CFR 236.814 - Station, control.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Station, control. 236.814 Section 236.814..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Definitions § 236.814 Station, control. The place where the control machine of a traffic control system is located. ...

Single-station 6C beamforming

Science.gov (United States)

Nakata, N.; Hadziioannou, C.; Igel, H.

2017-12-01

Six-component measurements of seismic ground motion provide a unique opportunity to identify and decompose seismic wavefields into different wave types and incoming azimuths, as well as estimate structural information (e.g., phase velocity). By using the relationship between the transverse component and vertical rotational motion for Love waves, we can find the incident azimuth of the wave and the phase velocity. Therefore, when we scan the entire range of azimuth and slownesses, we can process the seismic waves in a similar way to conventional beamforming processing, without using a station array. To further improve the beam resolution, we use the distribution of amplitude ratio between translational and rotational motions at each time sample. With this beamforming, we decompose multiple incoming waves by azimuth and phase velocity using only one station. We demonstrate this technique using the data observed at Wettzell (vertical rotational motion and 3C translational motions). The beamforming results are encouraging to extract phase velocity at the location of the station, apply to oceanic microseism, and to identify complicated SH wave arrivals. We also discuss single-station beamforming using other components (vertical translational and horizontal rotational components). For future work, we need to understand the resolution limit of this technique, suitable length of time windows, and sensitivity to weak motion.

Project JADE. Description of the MLH-method

International Nuclear Information System (INIS)

Sandstedt, H.; Munier, R.; Wichmann, C.; Isaksson, Therese

2001-08-01

This report constitutes a part of a series of reports within project JADE, comparison of deposition methods. A comparison of the deposition methods MLH (Medium Long Holes with approximately 25 copper canisters emplaced in a horizontal deposition hole about 200 metres in length bored between central and side tunnels) and KBS-3 (copper canisters are emplaced in vertical deposition holes bored in the floors of horizontal tunnels) has earlier been performed and KBS-3 was judged to be more advantageous than MLH. However, the prerequisites for the comparison have changed with time and an updated evaluation of MLH was therefore required. In this report, the current knowledge of MLH is summarized with focus on geological prerequisites, methods for boring long, horizontal deposition holes, reinforcement and sealing, deposition and cost. Comparisons with KBS-3 are performed sequentially. An MLH-repository is judged to be more sensitive to ingress of water to the deposition holes during the deposition process. This implies that a MLH repository based on today's knowledge is basically recommended for bedrock with fairly low water baring capacity. It has been demonstrated that MLH has considerable economic potential compared to KBS-3. However, the method is judged to be more technically immature than KBS-3. Particularly, methods and equipment for deposition of canisters need to be developed further. Methods and equipment for deposition can be developed, which fulfill the demands on function and safety, in the near future. MLH cannot therefore be rejected as deposition method

A distributed planning concept for Space Station payload operations

Science.gov (United States)

Hagopian, Jeff; Maxwell, Theresa; Reed, Tracey

1994-01-01

The complex and diverse nature of the payload operations to be performed on the Space Station requires a robust and flexible planning approach. The planning approach for Space Station payload operations must support the phased development of the Space Station, as well as the geographically distributed users of the Space Station. To date, the planning approach for manned operations in space has been one of centralized planning to the n-th degree of detail. This approach, while valid for short duration flights, incurs high operations costs and is not conducive to long duration Space Station operations. The Space Station payload operations planning concept must reduce operations costs, accommodate phased station development, support distributed users, and provide flexibility. One way to meet these objectives is to distribute the planning functions across a hierarchy of payload planning organizations based on their particular needs and expertise. This paper presents a planning concept which satisfies all phases of the development of the Space Station (manned Shuttle flights, unmanned Station operations, and permanent manned operations), and the migration from centralized to distributed planning functions. Identified in this paper are the payload planning functions which can be distributed and the process by which these functions are performed.

H2FIRST Reference Station Design Task: Project Deliverable 2-2

Energy Technology Data Exchange (ETDEWEB)

Pratt, Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Terlip, Danny [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Ainscough, Chris [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kurtz, Jennifer [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Elgowainy, Amgad [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-04-20

This report presents near-term station cost results and discusses cost trends of different station types. It compares various vehicle rollout scenarios and projects realistic near-term station utilization values using the station infrastructure rollout in California as an example. It describes near-term market demands and matches those to cost-effective station concepts. Finally, the report contains detailed designs for five selected stations, which include piping and instrumentation diagrams, bills of materials, and several site-specific layout studies that incorporate the setbacks required by NFPA 2, the National Fire Protection Association Hydrogen Technologies Code. This work identified those setbacks as a significant factor affecting the ability to site a hydrogen station, particularly liquid stations at existing gasoline stations. For all station types, utilization has a large influence on the financial viability of the station.

Study of the method of placing technical stations

Directory of Open Access Journals (Sweden)

Sattorov S.B.

2017-12-01

Full Text Available At present, the organization of transportation by rail is associated with the processing of trains and wagons along the route. Accommodation and equipping of technical stations play a major role in the organization of the transportation process. The uninterrupted operation of the technical stations ensures the stability of the railway transport as a whole. The distance between the technical stations determines the duration of operation of the locomotive crew, the efficient use of the locomotive, the required number of locomotive crews and locomotives for carrying out the transportation plan, and also improves the main indicators of the railway. However, often train locomotives do not fulfill their assigned tasks due to the lack of time for the locomotive crew in order to deliver the train to the nearest technical station, as well as the irrational use of the standard time of the locomotive crew. In connection with the expectation of delivery, the locomotive brigade replacing the locomotive, the idle time of the wagons at the intermediate stations increases. All this makes it difficult to control the movement of trains and reduces the speed of moving cars on the railway transport. The purpose of the study is to develop a method for placing technical stations on a railway test site in the course of an electric traction. To achieve this goal, it will be necessary to solve the following tasks: generalization of the main parameters of the location of technical stations; determination of half-races between technical stations in the operation of one locomotive brigade; search for the required number of change of the locomotive brigade; determination of the distance between technical stations. The methods of research are based on the generalization and analysis of existing results in finding the rational location of technical stations. Results: It is revealed that the first step for the rational placement of technical stations is to determine the

Station black out of Fukushima Daiichi Nuclear Power Station Unit 1 was not caused by tsunamis

International Nuclear Information System (INIS)

Ito, Yoshinori

2013-01-01

Station black out (SBO) of Fukushima Daiichi Nuclear Power Station Unit 1 would be concluded to be caused before 15:37 on March 11, 2011 because losses of emergency ac power A system was in 15:36 and ac losses of B system in 15:37 according to the data published by Tokyo Electric Power Co. (TEPCO) in May 10, 2013. Tsunami attacked the site of Fukushima Daiichi Nuclear Power Station passed through the position of wave amplitude meter installed at 1.5 km off the coast after 15:35 and it was also recognized tsunami arrived at the coast of Unit 4 sea side area around in 15:37 judging from a series of photographs taken from the south side of the site and general knowledge of wave propagation. From a series of photographs and witness testimony, tsunami didn't attack Fukushima Daiichi Nuclear Power Station uniformly and tsunami's arrival time at the site of Unit 1 would be far later than arrival time at the coast of Unit 4 sea side area, which suggested it would be around in 15:39. TEPCO insisted tsunami passed through 1.5 km off the coast around in 15:33 and clock of wave amplitude meter was incorrect, which might be wrong. Thus SBO of Fukushima Daiichi Nuclear Power Station Unit 1 occurred before tsunami's arrival at the site of Unit 1 and was not caused by tsunami. (T. Tanaka)

Autonomous Electrical Vehicles’ Charging Station

OpenAIRE

Józef Paska; Mariusz Kłos; Łukasz Rosłaniec; Rafał Bielas; Magdalena Błędzińska

2016-01-01

This paper presents a model of an autonomous electrical vehicles’ charging station. It consists of renewable energy sources: wind turbine system, photovoltaic cells, as well as an energy storage, load, and EV charging station. In order to optimise the operating conditions, power electronic converters were added to the system. The model was implemented in the Homer Energy programme. The first part of the paper presents the design assumptions and technological solutions. Further in the paper...

The Sewer Research Station in Frejlev

DEFF Research Database (Denmark)

Schaarup-Jensen, Kjeld; Hvitved-Jacobsen, T.

This report for the 2000 activities at the sewer research station in Frejlev. Only few - if any - sewer monitoring stations like the one in Frejlev exist. Without no doubt the field data produced - especially the time series - in the course of time will serve as a unique basis for projects dealin...

The Sewer Research Station in Frejlev

DEFF Research Database (Denmark)

Hvitved-Jacobsen, Thorkild; Schaarup-Jensen, Kjeld

This report for the 1999 activities at the sewer research station in Frejlev. Only few - if any - sewer monitoring stations like the one in Frejlev exist. Without no doubt the field data produced - especially the time series - in the course of time will serve as a unigue basis for projects dealin...

47 CFR 74.1283 - Station identification.

Science.gov (United States)

2010-10-01

... translator's call letters and location, giving the name, address and telephone number of the licensee or his... FM Broadcast Booster Stations § 74.1283 Station identification. (a) The call sign of an FM broadcast... requests for the assignment of particular combinations of letters will not be considered. (b) The call sign...

Policies of transnational Moroccan television station

Directory of Open Access Journals (Sweden)

Fathallah DAGHMI

2011-01-01

Full Text Available This work analyses the different televisions stations accessible to Moroccans living outside the country (Diaspora. It is particularly concerned with the discourse and representation of the managers of the stations. The objective is to understand the media available and the political and economic policies that guide them.

Shippingport Station Decommissioning Project: overview and justification

International Nuclear Information System (INIS)

Coffman, F.E.

1984-01-01

The purpose of this booklet is to brief the reader on the Shippingport Station Decommissioning Project and to summarize the benefits of funding the project in FY 1984. Background information on the station and the decommissioning project is provided in this section of the booklet; the need for a reactor decommissining demonstration is discussed in the next section; and a summary of how the Shippingport Station Decommissioning Project (SSDP) provides the needed demonstration is provided in the final section

Landscape model configuration for biosphere analysis of selected cases in TILA-99 and in KBS-3H safety evaluation, 2007

International Nuclear Information System (INIS)

Broed, R.

2008-08-01

In this report, the configuration of a landscape model based on the Terrain and ecosystems development model of the Olkiluoto site, 2006, is presented in details. The landscape model is created especially for use in the simulations of release cases in the KBS-3H safety evaluation and for recalculating some older cases originally presented in the TILA-99 safety assessment. The report presents results for constant unit release rate on the landscape doses, and activity concentrations and radionuclide inventories in the various environmental media. Results on the specific release cases are left for subsequent reports. In this report, the discussion and presentation of the results is focused on a limited set of radionuclides (Cl-36, Tc-99, I-129, Ra-226, Th-230) of different behaviour in the environment. However, same results have been calculated also for a large variety of nuclides present in the release terms to the biosphere. In the sensitivity analysis the parameters most affecting to the results are identified. They are further evaluated using data quality index, reflecting to the confidence on the underlying data and knowledge base. These are then combined in the multi-dimensional uncertainty analysis, revealing water balance, the fraction of precipitation intercepted by the foliage, concentration ratios in forests, Kds in sediments, river width and wetland parameters in general as the most important factors, in respect of the unit release rate, calling for further research at the moment, together with some structural improvements to the biosphere object modules. Uncertainties related to the release locations are studied with a number of cases assuming various patterns of release distribution to several objects as well as the release term received by single objects. The maximum landscape doses per unit release rate vary between one and less than four orders of magnitude across the cases depending on the nuclide, or from more than two less to slightly more than one

Work place regulations - effects on power station construction

International Nuclear Information System (INIS)

Richter, E.

1979-01-01

The paper describes that the Workplace Order and Workplace Regulations cannot be applied in every area of a conventional power station or the conventional sections of nuclear power stations. In any case extensive regulations already exist for the hot regions of nuclear power stations. A proposal is made as to which areas of power stations should be developed in accordance with the Workplace Order and the Workplace Regulations and which areas are not deemed to be 'Workplaces'. This is illustrated with the aid of typical examples. (orig.) [de

30 CFR 77.309-1 - Control stations; location.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Control stations; location. 77.309-1 Section 77... MINES Thermal Dryers § 77.309-1 Control stations; location. Thermal dryer system control stations constructed after June 30, 1971, shall be installed at a location which will give to the operator of the...

29 CFR 793.15 - Duties away from the station.

Science.gov (United States)

2010-07-01

... 29 Labor 3 2010-07-01 2010-07-01 false Duties away from the station. 793.15 Section 793.15 Labor... Requirements for Exemption § 793.15 Duties away from the station. An employee who is “employed by” a radio or television station in one or more of the named occupations may perform his work at the station or away from...

Can we afford shutting down power stations?

International Nuclear Information System (INIS)

Hesse, David

2015-01-01

The author discusses and criticizes some popular beliefs on the profitability of nuclear power stations, on the fact that they are now too old to be exploited, and on the fact that nuclear energy is the most subsidised energy. As some European countries decided to phase out nuclear, he notices that the decrease of gas prices undermines the profitability of nuclear power stations in the USA and that new rules aimed at the reduction of CO 2 emissions result in high subsidies for renewable energies which are however handicapped by the grid ability to integrate all energies. He outlines that shutting down a nuclear power station costs a lot of money to the society, and denies the argument of non-profitability of these stations. He states that the issue of nuclear subsidies is in fact a matter of tax policy. He also states that these so-said old power stations take in fact advantage of numerous technical innovations for their equipment, components, technology and fuels which improve their efficiency, durability, performance and flexibility

Electrostatic pickup station

CERN Multimedia

CERN PhotoLab

1982-01-01

Electrostatic pickup station, with 4 interleaved electrodes, to measure beam position in the horizontal and vertical plane. This type is used in the transfer lines leaving the PS (TT2, TT70, TTL2). See also 7904075.

Porto Tolle thermoelectric power station and aquatic environment of Po Delta (Italy): Synthesis of data

International Nuclear Information System (INIS)

Ambrogi, R.

1990-01-01

The 2400 MW, oil-fueled power station of Porto Tolle (Italy) potentially affects riverine, lagoon and marine sectors of the Po Delta. A synthesis is provided of the data gathered by several research lines, which studied different aspects of the environment during the pre-operational and operational period. Comparisons are made between the two periods and between stations more or less influenced by cooling water discharge. When river water is used for cooling (the majority of cases), some effects on water quality characteristics and on plankton community abundances are evident in the immediate vicinity of the outlet. In the lagoon (Sacca del Canarin) and in the stretch of sea in front of it, effects directly connected with the thermal effluent could not be detected. The geomorphological evolution of the lagoon, however, was influenced by the hydraulic modification brought about by the cooling circuit. This resulted in an enhancement of the biological production of the lagoon. The sea area is not affected in a significant way, but concern is raised about the interaction of cooling discharge and the eutrophic load from the Po River

Environmental radiation monitoring system in nuclear power station

International Nuclear Information System (INIS)

Matsuoka, Sadazumi; Tadachi, Katsuo; Endo, Mamoru; Yuya, Hiroshi

1983-01-01

At the time of the construction of nuclear power stations, prior to their start of operation, the state of environmental radiation must be grasped. After the start of the power stations, based on those data, the system of environmental radiation monitoring is established. Along with the construction of Kashiwazaki-Kariwa Nuclear Power Station, The Tokyo Electric Power Co., Inc. jointly with Fujitsu Ltd. has developed a high-reliability, environmental radiation monitoring system, and adopted ''optical data highways'' using optical fiber cables for communication. It consists of a central monitoring station and 11 telemeter observation points, for collecting both radiation and meteorological data. The data sent to the central station through the highways are then outputted on a monitoring panel. They are analyzed with a central processor, and the results are printed out. (Mori, K.)

Long-term trends at the Boknis Eck time series station (Baltic Sea, 1957–2013: does climate change counteract the decline in eutrophication?

Directory of Open Access Journals (Sweden)

S. T. Lennartz

2014-11-01

Full Text Available The Boknis Eck (BE time series station, initiated in 1957, is one of the longest-operated time series stations worldwide. We present the first statistical evaluation of a data set of nine physical, chemical and biological parameters in the period of 1957–2013. In the past three to five decades, all of the measured parameters underwent significant long-term changes. Most striking is an ongoing decline in bottom water oxygen concentration, despite a significant decrease of nutrient and chlorophyll a concentrations. Temperature-enhanced oxygen consumption in the bottom water and a prolongation of the stratification period are discussed as possible reasons for the ongoing oxygen decline despite declining eutrophication. Observations at the BE station were compared with model output of the Kiel Baltic Sea Ice Ocean Model (BSIOM. Reproduced trends were in good agreement with observed trends for temperature and oxygen, but generally the oxygen concentration at the bottom has been overestimated.

Extension of life of nuclear power stations

International Nuclear Information System (INIS)

Takahashi, Hideaki

1991-01-01

At the time of designing nuclear power stations, as their service life, generally 40 years are taken, and the basic design specifications of machinery and equipment are determined. In USA where atomic energy has been developed, the new construction of nuclear power stations is cased for a while, however, if this situation continues as it is, since old power stations reach the service life of 40 years and are retired in near future, it is feared that the circumstance of the total amount of power generation becoming short will occur. As one of the countermeasures to this, the research on the extension of life of nuclear power stations has been carried out in many fields in USA, and it is expected that the application for extending the life for the power stations constructed in the initial period of development is submitted in 1991. The researches that have been carried out for solving the technical problems in this extension of life and the situation in Japan are reported. The NEC of USA decided that the operation period of nuclear power stations in USA, which is considered to be 40 years so far, can be extended up to the limit of 20 years. The background and circumstances of this problem in USA, Nuclear Plant Aging Research Program, Plant Life Extension Program and so on are reported. (K.I.)

Tokai earthquakes and Hamaoka Nuclear Power Station

International Nuclear Information System (INIS)

Komura, Hiroo

1981-01-01

Kanto district and Shizuoka Prefecture are designated as ''Observation strengthening districts'', where the possibility of earthquake occurrence is high. Hamaoka Nuclear Power Station, Chubu Electric Power Co., Inc., is at the center of this district. Nuclear power stations are vulnerable to earthquakes, and if damages are caused by earthquakes in nuclear power plants, the most dreadful accidents may occur. The Chubu Electric Power Co. underestimates the possibility and scale of earthquakes and the estimate of damages, and has kept on talking that the rock bed of the power station site is strong, and there is not the fear of accidents. However the actual situation is totally different from this. The description about earthquakes and the rock bed in the application of the installation of No.3 plant was totally rewritten after two years safety examination, and the Ministry of International Trade and Industry approved the application in less than two weeks thereafter. The rock bed is geologically evaluated in this paper, and many doubtful points in the application are pointed out. In addition, there are eight active faults near the power station site. The aseismatic design of the Hamaoka Nuclear Power Station assumes the acceleration up to 400 gal, but it may not be enough. The Hamaoka Nuclear Power Station is intentionally neglected in the estimate of damages in Shizuoka Prefecture. (Kako, I.)

47 CFR 97.207 - Space station.

Science.gov (United States)

2010-10-01

... FCC. (c) The following frequency bands and segments are authorized to space stations: (1) The 17 m, 15... notifications to the International Bureau, FCC, Washington, DC 20554. (1) A pre-space notification within 30... risk of collision and a description of what measures the space station operator plans to take to avoid...

Reducing lighting electricity use in underground metro stations

International Nuclear Information System (INIS)

Casals, Miquel; Gangolells, Marta; Forcada, Núria; Macarulla, Marcel

2016-01-01

Highlights: • Lighting systems are big energy consumers in underground metro stations. • An adaptive lighting system strategy is developed for underground stations. • Dimming controls are based on station occupancy levels and maintenance cycles. • The k-means clustering technique is used to identify stations’ occupancy patterns. • Savings were found to amount to 255.47 MW h in 2 years for a case study metro network. - Abstract: Lighting systems are usually one of the largest electrical end-uses in underground metro stations. Taking into account that budget restrictions in publicly owned companies hinder energy efficiency retrofit projects that require high initial investments, affordable energy saving strategies are needed. This paper presents a low-cost approach for reducing lighting electricity use in underground stations, without affecting passengers’ comfort or the metro operator’s service. For this purpose, an adaptive lighting strategy of dimming the illuminance levels of artificial light sources has been developed. Dimming controls are based on the occupancy of the station, and the preventive maintenance and cleaning cycles of the luminaires. The stations’ monthly occupancy patterns are defined through the k-means clustering technique. To illustrate its effectiveness, the method was applied to 115 underground stations of the Barcelona metro network. The results revealed overall electricity savings of 255.47 MW h on a biannual basis, which represents 36.22% of the stations’ baseline lighting consumption. Individual energy savings were found to range from 25 to 87.5 MW h/year in the stations of the Barcelona metro network, depending on the number and profile of station users. The research findings will undoubtedly be useful for the future energy efficiency project plans of worldwide metro operators and managers of other underground spaces.

RadNet Air Quality (Fixed Station) Data

Data.gov (United States)

U.S. Environmental Protection Agency — RadNet is a national network of monitoring stations that regularly collect air for analysis of radioactivity. The RadNet network, which has stations in each State,...

Technology development activities for housing research animals on Space Station Freedom

Science.gov (United States)

Jenner, Jeffrey W.; Garin, Vladimir M.; Nguyen, Frank D.

1991-01-01

The development and design of animal facilities are described in terms of the technological needs for NASA's Biological Flight Research Laboratory. Animal habitats are presented with illustrations which encompass waste-collection techniques for microgravity conditions that reduce the need for crew participation. The technology is intended to be highly compatible with animal morphology, and airflow is employed as the primary mechanism of waste control. The airflow can be utilized in the form of localized high-speed directed flow that simultaneously provides a clean animal habitat and low airflow rates. The design of an animal-habitat testbed is presented which capitalizes on contamination-control mechanisms and suitable materials for microgravity conditions. The developments in materials and technologies represent significant contributions for the design of the centrifuge facilities for the Space Station Freedom.

Operational characteristics of pediatric radiology: Image display stations

International Nuclear Information System (INIS)

Taira, R.K.

1987-01-01

The display of diagnostic images is accomplished in the UCLA Pediatric Radiology Clinical Radiology Imaging System (CRIS) using 3 different types of digital viewing stations. These include a low resolution station with six 512 x 512 monitors, a high resolution station with three 1024 x 1024 monitors, and a very high resolution workstation with two 2048 x 2048 monitors. The display stations provide very basic image processing manipulations including zoom and scroll, contrast enhancement, and contrast reversal. The display stations are driven by a computer system which is dedicated for clinical use. During times when the clinical computer is unavailable (maintenance or system malfunction), the 512 x 512 workstation can be switched to operate from a research PACS system in the UCLA Image Processing Laboratory via a broadband communication network. Our initial clinical implementation involves digital viewing for pediatric radiology conferences. Presentation of inpatient cases use the six monitor 512 x 512 multiple viewing station. Later stages of the clinical implementation involve the use of higher resolution displays for the purpose of primary diagnosis from video displays

Assessment of a KBS-3 nuclear waste repository as a plane of weakness

Energy Technology Data Exchange (ETDEWEB)

Loennqvist, Margareta; Kristensson, Ola; Faelth, Billy (Clay Technology AB, Lund (Sweden))

2010-06-15

The objective of this study is to investigate if the KBS-3 repository can act as a plane of weakness when subjected to different loads. These loads may cause either shear- or tensile fracturing. In this report these two modes of fracturing are simply referred to as 'Shearing' and 'Sheeting', respectively. The sensitivity of the rock mass to the presence of a system of tunnels is studied by means of numerical modelling using the two-dimensional distinct element code UDEC. In order to study the stability against shearing, the slip behaviours of two cases are compared: - A single fracture embedded in a portion of rock. - A single fracture embedded in a portion of rock is cutting through a system of tunnels, i.e. a repository. The evaluation concerns three issues: - How the presence of a system of tunnels affects the stability of the rock mass. - How the presence of a system of tunnels affects the shear displacements in the hypothetical case of complete failure. - How the tunnel spacing affects the stability and shear displacements. The above is investigated for a number of in situ stress states. The stress states are varied in absolute magnitude, ratio between major and minor principal stress and inclination of the major stress with respect to the fracture plane. The results from the models are used to evaluate the stability of the repository rock mass against shear failure in terms of Factor of Safety (FoS). The results indicate that the stability margin in the fracture has a limited sensitivity to the presence of the tunnels and to the tunnel spacing. Including tunnels with 40 m spacing gives a reduction of the stability margin by about 20% at a maximum. Applying the stress state where the stresses are oriented in order to give maximum instability gives a FoS higher than 1.4 for all tunnel spacings larger than 20 m. The stability is also evaluated using stress input from dynamic earthquake simulations. The FoS quantity is calculated based on the

Assessment of a KBS-3 nuclear waste repository as a plane of weakness

International Nuclear Information System (INIS)

Loennqvist, Margareta; Kristensson, Ola; Faelth, Billy

2010-06-01

The objective of this study is to investigate if the KBS-3 repository can act as a plane of weakness when subjected to different loads. These loads may cause either shear- or tensile fracturing. In this report these two modes of fracturing are simply referred to as 'Shearing' and 'Sheeting', respectively. The sensitivity of the rock mass to the presence of a system of tunnels is studied by means of numerical modelling using the two-dimensional distinct element code UDEC. In order to study the stability against shearing, the slip behaviours of two cases are compared: - A single fracture embedded in a portion of rock. - A single fracture embedded in a portion of rock is cutting through a system of tunnels, i.e. a repository. The evaluation concerns three issues: - How the presence of a system of tunnels affects the stability of the rock mass. - How the presence of a system of tunnels affects the shear displacements in the hypothetical case of complete failure. - How the tunnel spacing affects the stability and shear displacements. The above is investigated for a number of in situ stress states. The stress states are varied in absolute magnitude, ratio between major and minor principal stress and inclination of the major stress with respect to the fracture plane. The results from the models are used to evaluate the stability of the repository rock mass against shear failure in terms of Factor of Safety (FoS). The results indicate that the stability margin in the fracture has a limited sensitivity to the presence of the tunnels and to the tunnel spacing. Including tunnels with 40 m spacing gives a reduction of the stability margin by about 20% at a maximum. Applying the stress state where the stresses are oriented in order to give maximum instability gives a FoS higher than 1.4 for all tunnel spacings larger than 20 m. The stability is also evaluated using stress input from dynamic earthquake simulations. The FoS quantity is calculated based on the normal- and shear

Numerical modelling of fracture displacements due to thermal load from a KBS-3 repository

Energy Technology Data Exchange (ETDEWEB)

Hakami, Eva; Olofsson, Stig-Olof [Itasca Geomekanik AB, Stockholm (Sweden)

2002-01-01

The objective of the project has been to estimate the largest shear displacements that could be expected on a pre-existing fracture located in the repository area, due to the heat release from the deposited waste. Two-dimensional numerical analyses using the 'Universal Distinct Element Code' (UDEC) have been performed. The UDEC models represent a vertical cross section of a KBS-3 type repository with a large planar fracture intersecting a deposition hole at the repository centre. The extension, dip and mechanical properties of the fracture were changed in different models to evaluate the influence of these parameters on fracture shear displacements. The fracture was modelled using a Coulomb slip criterion with no cohesion and no dilation. The rock mass surrounding the fracture was modelled as a homogeneous, isotropic and elastic material, with a Young's modulus of 40 GPa. The initial heat release per unit repository area was assumed to be 8W/m{sup 2} (total power/total repository area). The shear displacements occur due to the thermal expansion of the rock surrounding the heat generating canisters. The rock mass is almost free to expand vertically, but is constrained horizontally, which gives a temperature-induced addition of shear stresses in the plane of the fracture. The shear movement of the fracture therefore follows the temperature development in the surrounding rock and the maximum shear displacement develops about 200 years after the waste deposition. Altogether, twenty cases are analysed. The maximum shear displacement, which occurs at the fracture centre, amounts to 0.2-13.8 cm depending on the fracture parameters. Among the analysed cases, the largest shear values, about 13 cm, was calculated for the cases with about 700 m long fractures with a shear stiffness of 0.005 GPa/m. Also, for large fractures with a higher shear stiffness of 5 GPa/m, but with a low friction angle (15 deg), the shear displacement reaches similar magnitudes, about

A Novel Methodology for Charging Station Deployment

Science.gov (United States)

Sun, Zhonghao; Zhao, Yunwei; He, Yueying; Li, Mingzhe

2018-02-01

Lack of charging stations has been a main obstacle to the promotion of electric vehicles. This paper studies deploying charging stations in traffic networks considering grid constraints to balance the charging demand and grid stability. First, we propose a statistical model for charging demand. Then we combine the charging demand model with power grid constraints and give the formulation of the charging station deployment problem. Finally, we propose a theoretical solution for the problem by transforming it to a Markov Decision Process.

Application of Queuing Theory to Petrol Stations in Benin-City Area ...

African Journals Online (AJOL)

This paper reports on a study conducted on five petrol stations in Benin City, namely: Oando petrol station Akpakpava, AP petrol station Ugbowo, Total petrol station Iselu, NNPC petrol station Benin-Auchi Road and NNPC Mega filling station Benin-Sapele Road. The average arrival rate of customers per hour for the five ...