WorldWideScience

Sample records for biological products manufacturing

  1. 78 FR 65904 - Permanent Discontinuance or Interruption in Manufacturing of Certain Drug or Biological Products

    Science.gov (United States)

    2013-11-04

    ... Manufacturing of Certain Drug or Biological Products AGENCY: Food and Drug Administration, HHS. ACTION: Proposed.... The Fabrazyme shortage resulted from contamination at the manufacturing [[Page 65910

  2. Permanent Discontinuance or Interruption in Manufacturing of Certain Drug or Biological Products. Final rule.

    Science.gov (United States)

    2015-07-08

    The Food and Drug Administration (FDA or the Agency) is amending its regulations to implement certain drug shortages provisions of the Federal Food, Drug, and Cosmetic Act (the FD&C Act), as amended by the Food and Drug Administration Safety and Innovation Act (FDASIA). The rule requires all applicants of covered approved drugs or biological products--including certain applicants of blood or blood components for transfusion and all manufacturers of covered drugs marketed without an approved application--to notify FDA electronically of a permanent discontinuance or an interruption in manufacturing of the product that is likely to lead to a meaningful disruption in supply (or a significant disruption in supply for blood or blood components) of the product in the United States.

  3. Manufacturing of curd products of increased biological value for the elderly from dried components.

    Science.gov (United States)

    Zabodalova, Ludmila A; Belozerova, Maria S; Evstigneeva, Tatiana N

    2018-01-01

    In recent years, the number of elderly people has increased, and the diseases that arise in old age are associated, amongst other factors, with malnutrition. In the elderly, the need for primary nutrients and energy changes, so the development of food products intended for this particular group of people is becom- ing increasingly important. The purpose of this research is to work out the composition of and technology for producing low-fat curd products from raw milk and vegetable components. The developed products can be used for their gerodietetic properties, because nutritional and energy needs in the elderly were taken into account when designing the product. The curd product was manufactured from skimmed dried milk (SDM), soy isolate protein (SIP) and spelt grain. Optimal conditions for the recombination of SIP were determined. The influence of mass fraction of SIP on the properties of the clot and the end product was studied. The degree of dispersion of the grain component was determined, from the organoleptic evaluation of samples of the mixture, and the optimum method of addition was chosen. The method of adding cooked spelt into the clot after pressing was chosen. Harrington’s generalized desirability function was used for the calculation of the optimum mass frac- tion of the grain component in the end product. The formulation and technology for a curd product based on dry ingredients were determined. The amino acid composition and content of essential components in the developed product were determined, and the biological and nutritional value were calculated. The use of dry ingredients for the production of a curd product makes it possible to manufac- ture the product in the absence of raw milk. The formulation of the product is designed taking into account the needs of the body in old age. The incorporation of spelt increases the biological value of the curd product to 81.5%.

  4. Very-large-scale production of antibodies in plants: The biologization of manufacturing.

    Science.gov (United States)

    Buyel, J F; Twyman, R M; Fischer, R

    2017-07-01

    Gene technology has facilitated the biologization of manufacturing, i.e. the use and production of complex biological molecules and systems at an industrial scale. Monoclonal antibodies (mAbs) are currently the major class of biopharmaceutical products, but they are typically used to treat specific diseases which individually have comparably low incidences. The therapeutic potential of mAbs could also be used for more prevalent diseases, but this would require a massive increase in production capacity that could not be met by traditional fermenter systems. Here we outline the potential of plants to be used for the very-large-scale (VLS) production of biopharmaceutical proteins such as mAbs. We discuss the potential market sizes and their corresponding production capacities. We then consider available process technologies and scale-down models and how these can be used to develop VLS processes. Finally, we discuss which adaptations will likely be required for VLS production, lessons learned from existing cell culture-based processes and the food industry, and practical requirements for the implementation of a VLS process. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

  5. Proof of concept for a banding scheme to support risk assessments related to multi-product biologics manufacturing.

    Science.gov (United States)

    Card, Jeffrey W; Fikree, Hana; Haighton, Lois A; Blackwell, James; Felice, Brian; Wright, Teresa L

    2015-11-01

    A banding scheme theory has been proposed to assess the potency/toxicity of biologics and assist with decisions regarding the introduction of new biologic products into existing manufacturing facilities. The current work was conducted to provide a practical example of how this scheme could be applied. Information was identified for representatives from the following four proposed bands: Band A (lethal toxins); Band B (toxins and apoptosis signals); Band C (cytokines and growth factors); and Band D (antibodies, antibody fragments, scaffold molecules, and insulins). The potency/toxicity of the representative substances was confirmed as follows: Band A, low nanogram quantities exert lethal effects; Band B, repeated administration of microgram quantities is tolerated in humans; Band C, endogenous substances and recombinant versions administered to patients in low (interferons), intermediate (growth factors), and high (interleukins) microgram doses, often on a chronic basis; and Band D, endogenous substances present or produced in the body in milligram quantities per day (insulin, collagen) or protein therapeutics administered in milligram quantities per dose (mAbs). This work confirms that substances in Bands A, B, C, and D represent very high, high, medium, and low concern with regard to risk of cross-contamination in manufacturing facilities, thus supporting the proposed banding scheme. Copyright © 2015 Elsevier Inc. All rights reserved.

  6. Application of manufactured products

    Science.gov (United States)

    Sastri, Sankar; Duke, Michael B.

    1992-01-01

    A wide range of products can be manufactured from the following materials: (1) lunar regolith or basalt; (2) regolith or rock beneficiated to concentrate plagioclase or other minerals; (3) iron, extracted from lunar soil or rocks by various means; (4) naturally occurring or easily obtained materials that have cementitious properties; and (5) byproducts of the above materials. Among the products that can be produced from these materials are the following: beams; plates and sheets; transparent plates (windows); bricks and blocks; pipes and tubes; low-density materials (foams); fiber, wire, and cables; foils and reflective coatings; hermetic seals (coatings); and formed objects. In addition to oxygen, which can be obtained by several processes, either from unbeneficiated regolith or by reduction of concentrated ilmenite, these materials make the simplest requirements of the lunar resource extraction system. A thorough analysis of the impact of these simplest products on the economics of space operations is not possible at this point. Research is necessary both to define optimum techniques and adapt them to space and to determine the probable market for the products so that the priority of various processes can be assessed. Discussions of the following products are presented: aerobraking heat shields; pressurized habitats; lunar photovoltaic farms; and agricultural systems.

  7. 21 CFR 680.2 - Manufacture of Allergenic Products.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Manufacture of Allergenic Products. 680.2 Section...) BIOLOGICS ADDITIONAL STANDARDS FOR MISCELLANEOUS PRODUCTS § 680.2 Manufacture of Allergenic Products. (a...) Cultures derived from microorganisms. Culture media into which organisms are inoculated for the manufacture...

  8. Nano Manufacturing - Products and Technologies

    DEFF Research Database (Denmark)

    Hansen, Hans Nørgaard; Alting, Leo

    2004-01-01

    The use of micro and nano technologies in components and products not only sets new demands to the manufacturing technologies. Product concepts have to be rethought and redefined in order to implement the micro and nano technologies into functional systems. Both a technology driven and a product ...

  9. Biological features produced by additive manufacturing processes using vat photopolymerization method

    DEFF Research Database (Denmark)

    Davoudinejad, Ali; Mendez Ribo, Macarena; Pedersen, David Bue

    2017-01-01

    of micro biological features by Additive Manufacturing (AM) processes. The study characterizes the additive manufacturing processes for polymeric micro part productions using the vat photopolymerization method. A specifically designed vat photopolymerization AM machine suitable for precision printing...

  10. Materials Manufactured from 3D Printed Synthetic Biology Arrays

    Science.gov (United States)

    Gentry, Diana; Micks, Ashley

    2013-01-01

    Many complex, biologically-derived materials have extremely useful properties (think wood or silk), but are unsuitable for space-related applications due to production, manufacturing, or processing limitations. Large-scale ecosystem-based production, such as raising and harvesting trees for wood, is impractical in a self-contained habitat such as a space station or potential Mars colony. Manufacturing requirements, such as the specialized equipment needed to harvest and process cotton, add too much upmass for current launch technology. Cells in nature are already highly specialized for making complex biological materials on a micro scale. We envision combining these strengths with the recently emergent technologies of synthetic biology and 3D printing to create 3D-structured arrays of cells that are bioengineered to secrete different materials in a specified three-dimensional pattern.

  11. Current trend in latex dipped products manufacturing

    International Nuclear Information System (INIS)

    Wong, W.S.C.

    1996-01-01

    The paper present the activities in dipped products manufacturing in Malaysia; the activities carried out by MARGMA - Malaysian Rubber Glove manufacturer; other issues discussed such as labour, pricing environmental issue, product certification in this activity

  12. Detailed design of product oriented manufacturing systems

    OpenAIRE

    Silva, Sílvio Carmo; Alves, Anabela Carvalho

    2006-01-01

    This paper presents a procedure for the detailed design and redesign of manufacturing systems within a framework of constantly fitting production system configuration to the varying production needs of products. With such an approach is achieved the design of Product Oriented Manufacturing Systems – POMS. This approach is in opposition to the fitting, before hand, of a production system to all products within a company. In this case is usual to adopt a Function Oriented Manufactur...

  13. Potential of Continuous Manufacturing for Liposomal Drug Products.

    Science.gov (United States)

    Worsham, Robert D; Thomas, Vaughan; Farid, Suzanne S

    2018-05-21

    Over the last several years, continuous manufacturing of pharmaceuticals has evolved from bulk APIs and solid oral dosages into the more complex realm of biologics. The development of continuous downstream processing techniques has allowed biologics manufacturing to realize the benefits (e.g. improved economics, more consistent quality) that come with continuous processing. If relevant processing techniques and principles are selected, the opportunity arises to develop continuous manufacturing designs for additional pharmaceutical products including liposomal drug formulations. Liposome manufacturing has some inherent aspects that make it favorable for a continuous process. Other aspects such as formulation refinement, materials of construction, and aseptic processing need development, but present an achievable challenge. This paper reviews the current state of continuous manufacturing technology applicable to liposomal drug product manufacturing and an assessment of the challenges and potential of this application. This article is protected by copyright. All rights reserved.

  14. Improved Methods for Production Manufacturing Processes in Environmentally Benign Manufacturing

    Directory of Open Access Journals (Sweden)

    Yan-Yan Wang

    2011-09-01

    Full Text Available How to design a production process with low carbon emissions and low environmental impact as well as high manufacturing performance is a key factor in the success of low-carbon production. It is important to address concerns about climate change for the large carbon emission source manufacturing industries because of their high energy consumption and environmental impact during the manufacturing stage of the production life cycle. In this paper, methodology for determining a production process is developed. This methodology integrates process determination from three different levels: new production processing, selected production processing and batch production processing. This approach is taken within a manufacturing enterprise based on prior research. The methodology is aimed at providing decision support for implementing Environmentally Benign Manufacturing (EBM and low-carbon production to improve the environmental performance of the manufacturing industry. At the first level, a decision-making model for new production processes based on the Genetic Simulated Annealing Algorithm (GSAA is presented. The decision-making model considers not only the traditional factors, such as time, quality and cost, but also energy and resource consumption and environmental impact, which are different from the traditional methods. At the second level, a methodology is developed based on an IPO (Input-Process-Output model that integrates assessments of resource consumption and environmental impact in terms of a materials balance principle for batch production processes. At the third level, based on the above two levels, a method for determining production processes that focus on low-carbon production is developed based on case-based reasoning, expert systems and feature technology for designing the process flow of a new component. Through the above three levels, a method for determining the production process to identify, quantify, assess, and optimize the

  15. Factors Affecting Labour Productivity in Manufacturing Enterprises

    Directory of Open Access Journals (Sweden)

    Zbigniew Gołaś

    2011-07-01

    Full Text Available The article presents the results of the analysis of the factors influencing labour productivity in the manufacturing business sector in 20042008. Labour productivity was analyzed in the context of the assets productivity, technical equipment of work, labour intensity of production, wages, value added and depreciation costs, and using linear stepwise regression. The study shows that despite significant progress, the level of labour productivity in domestic manufacturing significantly lower than the average in the European Union. Lower than in Poland, the level of labour productivity gain only companies in Romania, Bulgaria, Lithuania, Latvia and Estonia. Estimated parameters of the regression function showed that the most important determinants of labour productivity in manufacturing are technical equipment of work, labour intensity of production, assets productivity, level of added value in relation to revenues. These factors explain the variability of labour productivity in 20042008 in a high degree.

  16. Green electronics manufacturing creating environmental sensible products

    CERN Document Server

    Wang, John X

    2012-01-01

    Going ""green"" is becoming a major component of the mission for electronics manufacturers worldwide. While this goal seems simplistic, it poses daunting dilemmas. Yet, to compete effectively in the global economy, manufacturers must take the initiative to drive this crucial movement. Green Electronics Manufacturing: Creating Environmental Sensible Products provides you with a complete reference to design, develop, build, and install an electronic product with special consideration for the product's environmental impacts during its whole life cycle. The author discusses how to integrate the st

  17. Knowledge management toboost productivity in manufacturing ...

    African Journals Online (AJOL)

    Knowledge management toboost productivity in manufacturing. ... Journal of Fundamental and Applied Sciences ... The assessment tool is an important factor because knowledge management has a deep relationship with performance ...

  18. Biological hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Benemann, J.R. [Univ. of California, Berkeley, CA (United States)

    1995-11-01

    Biological hydrogen production can be accomplished by either thermochemical (gasification) conversion of woody biomass and agricultural residues or by microbiological processes that yield hydrogen gas from organic wastes or water. Biomass gasification is a well established technology; however, the synthesis gas produced, a mixture of CO and H{sub 2}, requires a shift reaction to convert the CO to H{sub 2}. Microbiological processes can carry out this reaction more efficiently than conventional catalysts, and may be more appropriate for the relatively small-scale of biomass gasification processes. Development of a microbial shift reaction may be a near-term practical application of microbial hydrogen production.

  19. Additive manufacturing in production: challenges and opportunities

    Science.gov (United States)

    Ahuja, Bhrigu; Karg, Michael; Schmidt, Michael

    2015-03-01

    Additive manufacturing, characterized by its inherent layer by layer fabrication methodology has been coined by many as the latest revolution in the manufacturing industry. Due to its diversification of Materials, processes, system technology and applications, Additive Manufacturing has been synonymized with terminology such as Rapid prototyping, 3D printing, free-form fabrication, Additive Layer Manufacturing, etc. A huge media and public interest in the technology has led to an innovative attempt of exploring the technology for applications beyond the scope of the traditional engineering industry. Nevertheless, it is believed that a critical factor for the long-term success of Additive Manufacturing would be its ability to fulfill the requirements defined by the traditional manufacturing industry. A parallel development in market trends and product requirements has also lead to a wider scope of opportunities for Additive Manufacturing. The presented paper discusses some of the key challenges which are critical to ensure that Additive Manufacturing is truly accepted as a mainstream production technology in the industry. These challenges would highlight on various aspects of production such as product requirements, process management, data management, intellectual property, work flow management, quality assurance, resource planning, etc. In Addition, changing market trends such as product life cycle, mass customization, sustainability, environmental impact and localized production will form the foundation for the follow up discussion on the current limitations and the corresponding research opportunities. A discussion on ongoing research to address these challenges would include topics like process monitoring, design complexity, process standardization, multi-material and hybrid fabrication, new material development, etc.

  20. The manufacturing of depleted uranium biological shield components

    International Nuclear Information System (INIS)

    Metelkin, J.A.

    1998-01-01

    The unique combination of the physical and mechanical properties of uranium made it possible to manufacture biological shield components of transport package container (TPC) for transportation nuclear power plant irradiated fuel and radionuclides of radiation diagnostic instruments. Protective properties are substantially dependent on the nature radionuclide composition of uranium, that why I recommended depleted uranium after radiation chemical processing. Depleted uranium biological shield (DUBS) has improved specific mass-size characteristics compared to a shield made of lead, steel or tungsten. Technological achievements in uranium casting and machining made it possible to manufacture DUBS components of TPC up to 3 tons of mass and up to 2 metres of the maximum size. (authors)

  1. Processes for manufacture of products from plants

    DEFF Research Database (Denmark)

    2010-01-01

    Disclosed herein is a process for inhibiting browning of plant material comprising adding a chelating agent to a disrupted plant material and adjusting the pH to a value of 2.0 to 4.5. Processes for manufacture of soluble and insoluble products from a plant material are also disclosed. Soluble...

  2. Micro-manufacturing: design and manufacturing of micro-products

    National Research Council Canada - National Science Library

    Koç, Muammer; Özel, Tuğrul

    2011-01-01

    .... After addressing the fundamentals and non-metallic-based micro-manufacturing processes in the semiconductor industry, it goes on to address specific metallic-based micro-manufacturing processes...

  3. A Single-use Strategy to Enable Manufacturing of Affordable Biologics

    Directory of Open Access Journals (Sweden)

    Renaud Jacquemart

    2016-01-01

    Full Text Available The current processing paradigm of large manufacturing facilities dedicated to single product production is no longer an effective approach for best manufacturing practices. Increasing competition for new indications and the launch of biosimilars for the monoclonal antibody market have put pressure on manufacturers to produce at lower cost. Single-use technologies and continuous upstream processes have proven to be cost-efficient options to increase biomass production but as of today the adoption has been only minimal for the purification operations, partly due to concerns related to cost and scale-up. This review summarizes how a single-use holistic process and facility strategy can overcome scale limitations and enable cost-efficient manufacturing to support the growing demand for affordable biologics. Technologies enabling high productivity, right-sized, small footprint, continuous, and automated upstream and downstream operations are evaluated in order to propose a concept for the flexible facility of the future.

  4. Standardization in biological staining. The influence of dye manufacturing

    DEFF Research Database (Denmark)

    Lyon, H

    2000-01-01

    not have been subjected to quality assessment either internally by the producer or vendor or externally by independent investigators or organizations such as the Biological Stain Commission. Concerted attempts at standardization in Europe are discussed. The latest results of this work, the European...... standard EN 12376, is presented. This standard is concerned with information supplied by the manufacturer with in vitro diagnostic reagents for biological staining. The standard has been prepared by a Working Group on Staining in Biology under Technical Committee 140, In Vitro Medical Devices...

  5. Process for the manufacture of whey products

    Energy Technology Data Exchange (ETDEWEB)

    Blanie, P

    1980-01-01

    Whey is subjected to ultrafiltration to retain about 10% of the T5, whilst the permeate is demineralized to 7% or less ash in the final product and dried to 3% moisture. The product, containing (in DM) 75% or more lactose, 6% or less protein and 8% or less minerals, is hydrolysed, e.g. with beta-galactosidase. It may be used for replacing sucrose, in the manufacture of a range of foods. Applications include chewing gum, fondants, nougats, chocolate, bakery and confectionery products as well as cream and yoghurt.

  6. Manufacturers Mergers and Product Variety in Vertically Related Markets

    OpenAIRE

    Chrysovalantou Milliou; Joel Sandonis

    2014-01-01

    We study final product manufacturers’ incentives to introduce new products into the market and how they are affected by a merger among them. We show that when manufacturers distribute their products through multi-product retailers, a manufacturers merger, although it leads to an increase in the wholesale prices, it can enhance product variety. The merger generated product variety efficiencies though arise only when vertical relations are present: when manufacturers sell directly their produ...

  7. Real-time product attribute control to manufacture antibodies with defined N-linked glycan levels.

    Science.gov (United States)

    Zupke, Craig; Brady, Lowell J; Slade, Peter G; Clark, Philip; Caspary, R Guy; Livingston, Brittney; Taylor, Lisa; Bigham, Kyle; Morris, Arvia E; Bailey, Robert W

    2015-01-01

    Pressures for cost-effective new therapies and an increased emphasis on emerging markets require technological advancements and a flexible future manufacturing network for the production of biologic medicines. The safety and efficacy of a product is crucial, and consistent product quality is an essential feature of any therapeutic manufacturing process. The active control of product quality in a typical biologic process is challenging because of measurement lags and nonlinearities present in the system. The current study uses nonlinear model predictive control to maintain a critical product quality attribute at a predetermined value during pilot scale manufacturing operations. This approach to product quality control ensures a more consistent product for patients, enables greater manufacturing efficiency, and eliminates the need for extensive process characterization by providing direct measures of critical product quality attributes for real time release of drug product. © 2015 American Institute of Chemical Engineers.

  8. Production of RVNRL and manufacture of products from it

    International Nuclear Information System (INIS)

    Vijayakumar, K.C.; Jacob, J.

    1996-01-01

    The procedure of the trial irradiation of latex at the pilot plant are discussed. Factory influencing the quality of RVNRL during trial production are identified. Procedure for processing of radiation prevulcanised latex into end products has been standardised. Household gloves, industrial gloves, to), balloons, blood transfusion tubes and nipples are manufactured commercially from RVNRL produced at Rubber Board

  9. Raw materials in the manufacture of biotechnology products: regulatory considerations.

    Science.gov (United States)

    Cordoba-Rodriguez, Ruth

    2010-01-01

    The Food and Drug Administration's Pharmaceutical cGMPs for the 21st Century initiative emphasizes science and risk-based approaches in the manufacture of drugs. These approaches are reflected in the International Conference on Harmonization (ICH) guidances ICH Q8, Q9, and Q10 and encourage a comprehensive assessment of the manufacture of a biologic, including all aspects of manufacture that have the potential to affect the finished drug product. Appropriate assessment and management of raw materials are an important part of this initiative. Ideally, a raw materials program should strive to assess and minimize the risk to product quality. With this in mind, risk-assessment concepts and control strategies will be discussed and illustrated by examples, with an emphasis on the impact of raw materials on cell substrates. Finally, the life cycle of the raw material will be considered, including its potential to affect the drug product life cycle. In this framework, the supply chain and the vendor-manufacturer relationship will be explored as important parts of an adequate raw materials control strategy.

  10. 77 FR 48992 - Tobacco Product Manufacturing Facility Visits

    Science.gov (United States)

    2012-08-15

    ... manufacture, preproduction design validation (including a process to assess the performance of a tobacco... about the manufacturing practices and processes unique to your facility and regulated tobacco products... process, package, label, and distribute different types of regulated tobacco products (cigarettes...

  11. Lean Manufacturing Implementation: an Approach to Reduce Production Cost

    Directory of Open Access Journals (Sweden)

    Iraswari

    2012-04-01

    Full Text Available Abstract: Lean Manufacturing Implementation: An Approach To Reduce Production Cost. Opportunities to improve production processes and reduce production cost through the implementation of lean manufacturing in small medium garment manufacturing are presented in this research. This research shows that there is a possibility of decrease in production cost and increase in return on sales. Lean manufacturing implementation can eliminate waste in the production process. This is a set of techniques for identification and elimination of waste gathered from The Ford Production, Statistical Process Control and other techniques. Improvement of quality could be carried out while time and cost of production are being reduced.

  12. Fatigue crack growth in additive manufactured products

    Directory of Open Access Journals (Sweden)

    A. Riemer

    2015-10-01

    Full Text Available Additive Manufacturing (AM is a new innovative technique that allows the direct fabrication of complex, individual, delicate and high-strength products, based on their 3D data. Selective Laser Melting (SLM is one of the AM processes that generates metallic components layer by layer using powder-bed technique. The irradiation and consequent melting of metallic powder is realised by the laser source. Employing SLM, especially complex and individual products, such as implants or aerospace parts, are well suited for economic production in small batches. The first important issue in this work was to analyse the fatigue crack growth (FCG in titanium alloy Ti-6-4 and stainless steel 316L processed by SLM. As a first step, stress intensity range decreasing tests were performed on SLM samples in their “as-built” condition. The next step was to adopt measures for optimisation of fatigue crack growth performance of SLM parts. For this purpose various heat treatments such as stress relief annealing and hot isostatic pressing (HIP were applied to the CT specimens. Finally, the strong impact of heat treatment on the residual lifetime was demonstrated by numerical fatigue crack growth simulations. For this purpose, the hip joint implant consisting of Ti-6-4 and processed by SLM was taken into account. It was found that residual stresses have a strong influence on the crack growth in Ti-6-4, while the influence of the micro-pores on the threshold values remains low. In contrast the results for 316L show that its fracturemechanical behaviour is not affected by residual stresses, whereas the microstructural features lead to modification in the da/dN-K-data. The second fundamental aim of this work was to demonstrate the possibilities of the SLM process. For that reason, the individually tailored bicycle crank was optimised regarding its weight and local stresses and finally manufactured using the SLM system. The iterative optimisation procedure was based on

  13. Research on Digital Product Modeling Key Technologies of Digital Manufacturing

    Institute of Scientific and Technical Information of China (English)

    DING Guoping; ZHOU Zude; HU Yefa; ZHAO Liang

    2006-01-01

    With the globalization and diversification of the market and the rapid development of Information Technology (IT) and Artificial Intelligence (AI), the digital revolution of manufacturing is coming. One of the key technologies in digital manufacturing is product digital modeling. This paper firstly analyzes the information and features of the product digital model during each stage in the product whole lifecycle, then researches on the three critical technologies of digital modeling in digital manufacturing-product modeling, standard for the exchange of product model data and digital product data management. And the potential signification of the product digital model during the process of digital manufacturing is concluded-product digital model integrates primary features of each stage during the product whole lifecycle based on graphic features, applies STEP as data exchange mechanism, and establishes PDM system to manage the large amount, complicated and dynamic product data to implement the product digital model data exchange, sharing and integration.

  14. AN EXPLORATORY STUDY OF MANUFACTURING STRATEGY OF PACKAGING PRODUCT-MANUFACTURING COMPANIES IN INDIA

    Directory of Open Access Journals (Sweden)

    Pradip P. Patil

    2012-09-01

    Full Text Available This paper presents finding of a survey on manufacturing strategy implementation (MSI adopted by the Indian packaging product manufacturing companies (IPPMC. Though the companies differ in terms of prod uct types (shape, method, content and material of packaging, conversion system, sales volume and sophistication of machinery used, they share common purpose that are used for packaging the product s . With growth in demand for consumer products, packaging f orms basis of differentiating products from competitors. The survey shows emphasis on implementation of manufacturing strategy, key decision areas, identifies competitive priorities, order winners. To get insight, three companies are selected for detailed case studies.

  15. PDC Journeys to Product Analysis Development and Additive Manufacturing?

    International Nuclear Information System (INIS)

    Shalina Sheik Muhamad

    2015-01-01

    The technology for product development and manufacturing has gone through many advancements. It is widely recognised that it would provide competitive advantage for engineering organization in term of product development cycle, productivity, sustainability and efficiency. We begin by describing the general characteristic of design process that will need to be integrated in product life cycle management. In Nuclear Malaysia, especially in engineering design activities the majority have been using 3D modelling. This paper discusses on the current product design practiced in Nuclear Malaysia, new product development process and new manufacturing technique which is additive manufacturing. (author)

  16. Mass customization and build to order production - in manufacturing networks

    DEFF Research Database (Denmark)

    Svensson, Carsten

    2003-01-01

    in the manufacturing as information processing is accountable for an increasing portion of the value creation. In order to improve the information processing some manufacturers have applied product models, thereby giving the customer access to the manufactures knowledge base. This project will introduce solution......Mass Customization and Build to Order Production – In Manufacturing Networks Mass customization and globalization have radically changed the environment for manufacturers. A new context is emerging with intensified competition and accelerated technology development. In this environment evolution...... is not an option, but a necessity for survival. This leads to the question “what can manufacturing enterprises do to turn the development into their own advantage?” As competition intensifies customer are increasingly demanding sophisticated and adapted solutions. Conventional manufacturer are challenged...

  17. Radical production in biological systems

    International Nuclear Information System (INIS)

    Johnson, J.R.; Akabani, G.

    1994-10-01

    This paper describes our effort to develop a metric for radiation exposure that is more fundamental than adsorbed dose and upon which a metric for exposure to chemicals could be based. This metric is based on the production of radicals by the two agents. Radicals produced by radiation in biological systems commonly assumed to be the same as those produced in water despite the presence of a variety of complex molecules. This may explain why the extensive efforts to describe the relationship between energy deposition (track structure) and molecular damage to DNA, based on the spectrum of radicals produced, have not been successful in explaining simple biological effects such as cell killing. Current models assume that DNA and its basic elements are immersed in water-like media and only model the production and diffusion of water-based radicals and their interaction with DNA structures; these models lack the cross sections associated with each macro-component of DNA and only treat water-based radicals. It has been found that such models are not realistic because DNA is not immersed in pure water. A computer code capable of simulating electron tracks, low-energy electrons, energy deposition in small molecules, and radical production and diffusion in water like media has been developed. This code is still in at a primitive stage and development is continuing. It is being used to study radical production by radiation, and radical diffusion and interactions in simple molecular systems following their production. We are extending the code to radical production by chemicals to complement our PBPK modeling efforts. It therefore has been developed primarily for use with radionuclides that are in biological materials, and not for radiation fields

  18. Synthetic Biology Guides Biofuel Production

    Directory of Open Access Journals (Sweden)

    Michael R. Connor

    2010-01-01

    Full Text Available The advancement of microbial processes for the production of renewable liquid fuels has increased with concerns about the current fuel economy. The development of advanced biofuels in particular has risen to address some of the shortcomings of ethanol. These advanced fuels have chemical properties similar to petroleum-based liquid fuels, thus removing the need for engine modification or infrastructure redesign. While the productivity and titers of each of these processes remains to be improved, progress in synthetic biology has provided tools to guide the engineering of these processes through present and future challenges.

  19. Production of a biological surfactant

    Directory of Open Access Journals (Sweden)

    N. Gladys Rosero

    2002-01-01

    Full Text Available This paper summarizes the scale up work performed at the Colombian Petroleum Institute on a process to produce at pilot plant level a biosurfactant of the rhamnolipid type. By examination of both the activation conditions of the microorganism and design aspects of the broth, a stable condition was achieved which consistently triggers the production mechanisms and thus it was obtained a significant increment in biosurfactant productivity. The biological surfactant exhibited high efficiency in applications such as hydrocarbon biodegradation in saline environments, corrosion inhibition, and crude oil recovery from storage tank bottom sludges.

  20. Designing Integrated Product- Service System Solutions in Manufacturing Industries

    DEFF Research Database (Denmark)

    Costa, Nina; Patrício, Lia; Morelli, Nicola

    2015-01-01

    Manufacturing firms are increasingly evolving towards the design of integrated product-service solutions but servitization literature does not provide specific guidance on how to design these integrated solutions. Building upon ProductService System (PSS) and Service Design (SD) approaches...... how it brings new insights to manufacturing companies moving to a service, value cocreation perspective....

  1. Predictive Manufacturing: A Classification Strategy to Predict Product Failures

    DEFF Research Database (Denmark)

    Khan, Abdul Rauf; Schiøler, Henrik; Kulahci, Murat

    2018-01-01

    manufacturing analytics model that employs a big data approach to predicting product failures; third, we illustrate the issue of high dimensionality, along with statistically redundant information; and, finally, our proposed method will be compared against the well-known classification methods (SVM, K......-nearest neighbor, artificial neural networks). The results from real data show that our predictive manufacturing analytics approach, using genetic algorithms and Voronoi tessellations, is capable of predicting product failure with reasonable accuracy. The potential application of this method contributes...... to accurately predicting product failures, which would enable manufacturers to reduce production costs without compromising product quality....

  2. Modeling of Agile Intelligent Manufacturing-oriented Production Scheduling System

    Institute of Scientific and Technical Information of China (English)

    Zhong-Qi Sheng; Chang-Ping Tang; Ci-Xing Lv

    2010-01-01

    Agile intelligent manufacturing is one of the new manufacturing paradigms that adapt to the fierce globalizing market competition and meet the survival needs of the enterprises, in which the management and control of the production system have surpassed the scope of individual enterprise and embodied some new features including complexity, dynamicity, distributivity, and compatibility. The agile intelligent manufacturing paradigm calls for a production scheduling system that can support the cooperation among various production sectors, the distribution of various resources to achieve rational organization, scheduling and management of production activities. This paper uses multi-agents technology to build an agile intelligent manufacturing-oriented production scheduling system. Using the hybrid modeling method, the resources and functions of production system are encapsulated, and the agent-based production system model is established. A production scheduling-oriented multi-agents architecture is constructed and a multi-agents reference model is given in this paper.

  3. 78 FR 18234 - Service of Process on Manufacturers; Manufacturers Importing Electronic Products Into the United...

    Science.gov (United States)

    2013-03-26

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration 21 CFR Part 1005 [Docket No. FDA-2007-N-0091; (formerly 2007N-0104)] Service of Process on Manufacturers; Manufacturers Importing Electronic Products Into the United States; Agent Designation; Change of Address AGENCY: Food and Drug...

  4. Agent Technology in Agile Multiparallel Manufacturing and Product Support

    NARCIS (Netherlands)

    van Moergestel, L.J.M.

    2014-01-01

    The thesis describes the application of agent technology in product manufacturing and product support. Important issues in the requirements of modern production are short time to market, requirement-driven production and low cost small quantity production. To meet these requirements special low cost

  5. Interactomes, manufacturomes and relational biology: analogies between systems biology and manufacturing systems

    Science.gov (United States)

    2011-01-01

    Background We review and extend the work of Rosen and Casti who discuss category theory with regards to systems biology and manufacturing systems, respectively. Results We describe anticipatory systems, or long-range feed-forward chemical reaction chains, and compare them to open-loop manufacturing processes. We then close the loop by discussing metabolism-repair systems and describe the rationality of the self-referential equation f = f (f). This relationship is derived from some boundary conditions that, in molecular systems biology, can be stated as the cardinality of the following molecular sets must be about equal: metabolome, genome, proteome. We show that this conjecture is not likely correct so the problem of self-referential mappings for describing the boundary between living and nonliving systems remains an open question. We calculate a lower and upper bound for the number of edges in the molecular interaction network (the interactome) for two cellular organisms and for two manufacturomes for CMOS integrated circuit manufacturing. Conclusions We show that the relevant mapping relations may not be Abelian, and that these problems cannot yet be resolved because the interactomes and manufacturomes are incomplete. PMID:21689427

  6. International photovoltaic products and manufacturers directory, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Shepperd, L.W. [ed.] [Florida Solar Energy Center, Cocoa, FL (United States)

    1995-11-01

    This international directory of more than 500 photovoltaic-related manufacturers is intended to guide potential users of photovoltaics to sources for systems and their components. Two indexes help the user to locate firms and materials. A glossary describes equipment and terminology commonly used in the photovoltaic industry.

  7. Additive manufacturing techniques for the production of tissue engineering constructs.

    Science.gov (United States)

    Mota, Carlos; Puppi, Dario; Chiellini, Federica; Chiellini, Emo

    2015-03-01

    'Additive manufacturing' (AM) refers to a class of manufacturing processes based on the building of a solid object from three-dimensional (3D) model data by joining materials, usually layer upon layer. Among the vast array of techniques developed for the production of tissue-engineering (TE) scaffolds, AM techniques are gaining great interest for their suitability in achieving complex shapes and microstructures with a high degree of automation, good accuracy and reproducibility. In addition, the possibility of rapidly producing tissue-engineered constructs meeting patient's specific requirements, in terms of tissue defect size and geometry as well as autologous biological features, makes them a powerful way of enhancing clinical routine procedures. This paper gives an extensive overview of different AM techniques classes (i.e. stereolithography, selective laser sintering, 3D printing, melt-extrusion-based techniques, solution/slurry extrusion-based techniques, and tissue and organ printing) employed for the development of tissue-engineered constructs made of different materials (i.e. polymeric, ceramic and composite, alone or in combination with bioactive agents), by highlighting their principles and technological solutions. Copyright © 2012 John Wiley & Sons, Ltd.

  8. Lean manufacturing: A better way for enhancement in productivity

    Science.gov (United States)

    Kumar Ahir, Pankaj; Kumar Yadav, Lalit; Singh Chandrawat, Saurabh

    2012-03-01

    Productivity is the impact of peoples working together. Machines are merely an extended way of collective imagination and energy. Lean Manufacturing is the most used method for continues improvement of business. Organization management philosophy focusing on the reduction of wastage to improve overall customer value. "Lean" operating principles began in manufacturing environments and are known by a variety of synonyms; Lean Manufacturing, Lean Production, Toyota Production System, etc. It is commonly believed that Lean started in Japan "The notable activities in keeping the price of Ford products low is the steady restriction of the production cycle. The longer an article is in the process of manufacture and the more it is moved about, the greater is its ultimate cost." "A systematic approach to identifying and eliminating waste through continuous improvement, flowing the product at the pull of the customer in pursuit of perfection."

  9. Specificity of Good Manufacturing Practice (GMP) for Biomedical Cell Products.

    Science.gov (United States)

    Tulina, M A; Pyatigorskaya, N V

    2018-03-01

    The article describes special aspects of Good Manufacturing Practice (GMP) for biomedical cell products (BMCP) that imply high standards of aseptics throughout the entire productio process, strict requirements to donors and to the procedure of biomaterial isolation, guaranty of tracing BMCP products, defining processing procedures which allow to identify BMCP as minimally manipulated; continuous quality control and automation of the control process at all stages of manufacturing, which will ensure product release simultaneously with completion of technological operations.

  10. Product Family Modelling for Manufacturing Planning

    DEFF Research Database (Denmark)

    Jørgensen, Kaj Asbjørn; Petersen, Thomas Ditlev; Nielsen, Kjeld

    2011-01-01

    To enable product configuration of a product family, it is important to develop a model of the selected product family. From such a model, an often performed practice is to make a product configurator from which customers can specify individual products from the family. To get further utilisation...

  11. Human Embryonic Kidney 293 Cells: A Vehicle for Biopharmaceutical Manufacturing, Structural Biology, and Electrophysiology.

    Science.gov (United States)

    Hu, Jianwen; Han, Jizhong; Li, Haoran; Zhang, Xian; Liu, Lan Lan; Chen, Fei; Zeng, Bin

    2018-01-01

    Mammalian cells, e.g., CHO, BHK, HEK293, HT-1080, and NS0 cells, represent important manufacturing platforms in bioengineering. They are widely used for the production of recombinant therapeutic proteins, vaccines, anticancer agents, and other clinically relevant drugs. HEK293 (human embryonic kidney 293) cells and their derived cell lines provide an attractive heterologous system for the development of recombinant proteins or adenovirus productions, not least due to their human-like posttranslational modification of protein molecules to provide the desired biological activity. Secondly, they also exhibit high transfection efficiency yielding high-quality recombinant proteins. They are easy to maintain and express with high fidelity membrane proteins, such as ion channels and transporters, and thus are attractive for structural biology and electrophysiology studies. In this article, we review the literature on HEK293 cells regarding their origins but also stress their advancements into the different cell lines engineered and discuss some significant aspects which make them versatile systems for biopharmaceutical manufacturing, drug screening, structural biology research, and electrophysiology applications. © 2018 S. Karger AG, Basel.

  12. External designers in product design processes of small manufacturing firms

    NARCIS (Netherlands)

    Berends, Hans; Reymen, Isabelle; Stultiëns, Rutger G L; Peutz, Murk

    Small manufacturing firms often fail to reap the benefits of good design practices. This study investigates how the involvement of external designers influences the evolution of product design processes in small manufacturing firms. Qualitative and quantitative process research methods were used to

  13. 3D-Printed Chips: Compatibility of Additive Manufacturing Photopolymeric Substrata with Biological Applications

    Directory of Open Access Journals (Sweden)

    Megan Carve

    2018-02-01

    Full Text Available Additive manufacturing (AM is ideal for building adaptable, structurally complex, three-dimensional, monolithic lab-on-chip (LOC devices from only a computer design file. Consequently, it has potential to advance micro- to milllifluidic LOC design, prototyping, and production and further its application in areas of biomedical and biological research. However, its application in these areas has been hampered due to material biocompatibility concerns. In this review, we summarise commonly used AM techniques: vat polymerisation and material jetting. We discuss factors influencing material biocompatibility as well as methods to mitigate material toxicity and thus promote its application in these research fields.

  14. Product costing program for wood component manufacturers

    Science.gov (United States)

    Adrienn Andersch; Urs Buehlmann; Jeff Palmer; Janice K Wiedenbeck; Steve. Lawser

    2013-01-01

    Accurate and timely product costing information is critically important for companies in planning the optimal utilization of company resources. While an overestimation of product costs can lead to loss of potential business and market share, underestimation of product costs can result in financial losses to the company. This article introduces a product costing program...

  15. Developmental engineering: a new paradigm for the design and manufacturing of cell-based products. Part II: from genes to networks: tissue engineering from the viewpoint of systems biology and network science.

    Science.gov (United States)

    Lenas, Petros; Moos, Malcolm; Luyten, Frank P

    2009-12-01

    The field of tissue engineering is moving toward a new concept of "in vitro biomimetics of in vivo tissue development." In Part I of this series, we proposed a theoretical framework integrating the concepts of developmental biology with those of process design to provide the rules for the design of biomimetic processes. We named this methodology "developmental engineering" to emphasize that it is not the tissue but the process of in vitro tissue development that has to be engineered. To formulate the process design rules in a rigorous way that will allow a computational design, we should refer to mathematical methods to model the biological process taking place in vitro. Tissue functions cannot be attributed to individual molecules but rather to complex interactions between the numerous components of a cell and interactions between cells in a tissue that form a network. For tissue engineering to advance to the level of a technologically driven discipline amenable to well-established principles of process engineering, a scientifically rigorous formulation is needed of the general design rules so that the behavior of networks of genes, proteins, or cells that govern the unfolding of developmental processes could be related to the design parameters. Now that sufficient experimental data exist to construct plausible mathematical models of many biological control circuits, explicit hypotheses can be evaluated using computational approaches to facilitate process design. Recent progress in systems biology has shown that the empirical concepts of developmental biology that we used in Part I to extract the rules of biomimetic process design can be expressed in rigorous mathematical terms. This allows the accurate characterization of manufacturing processes in tissue engineering as well as the properties of the artificial tissues themselves. In addition, network science has recently shown that the behavior of biological networks strongly depends on their topology and has

  16. Lean Production Applications in a Manufacturing Company

    OpenAIRE

    Ali Görener; Humeyra Baser; Ali Turkyilmaz

    2013-01-01

    Lean production is a production model which comes about the pursuit of companies to be able to meet competition and make effective production. The main purpose of lean production is to get control about the wastage. This study includes the requirements for the success of the lean production and how the lean production system can be established. In this paper, lean production techniques were applied to the electric water heater line. Measurements using lean initiatives were made, operation cyc...

  17. Identifying variables that influence manufacturing product quality

    Directory of Open Access Journals (Sweden)

    Marek Krynke

    2014-10-01

    Full Text Available In the article a risk analysis of the production process of selected products in a plant producing votive candles was conducted. The Pareto-Lorenz diagram and FMEA method were used which indicated the most important areas affecting the production of selected elements of candles. The synthesis of intangible factors affecting production in the audited company was also carried out with particular emphasis on the operation of the production system. The factors determining the validity of studies was examined, describing the principle of BOST 14 Toyota management. The most important areas of the company were identified, positively affecting the production process.

  18. Age, wage and productivity in Dutch manufacturing

    NARCIS (Netherlands)

    van Ours, J.C.; Stoeldraijer, L.

    2011-01-01

    Previous empirical studies on the effect of age on productivity and wages find contradicting results. Some studies find that if workers grow older there is an increasing gap between productivity and wages, i.e. wages increase with age while productivity does not or does not increase at the same

  19. Carbon composite manufacturing in automotive volume production

    DEFF Research Database (Denmark)

    Geiger, Raphael; Pahl, Julia

    2017-01-01

    Lightweight constructions are a continuously increasing trend in the automotive industry. Main drivers for that trend are the challenging emission reduction targets regarding combustion engines and increasing ranges in electric mobility. This article presents different composite production methods...... and discusses their ability within mass production giving also an example within the automotive production....

  20. Productivity Measurement in Manufacturing and the Expenditure Approach

    DEFF Research Database (Denmark)

    Schjerning, Bertel; Sørensen, Anders

    2008-01-01

    This paper studies conversion factors based on the expenditure approach and evaluates the appropriateness for international comparisons of output levels in manufacturing. We apply a consistency check based on the insight that relative productivity levels should be invariant to the choice of base....... The conclusion is insensitive to the applied method for developing conversion factors. The implication is that we cannot measure relative productivity levels in manufacturing across countries using the expenditure approach....

  1. Services trade restrictiveness and manufacturing productivity : the role of institutions

    OpenAIRE

    BEVERELLI, Cosimo; FIORINI, Matteo; HOEKMAN, Bernard M.

    2015-01-01

    We study the effect of services trade restrictiveness on manufacturing productivity for a broad cross-section of countries at different stages of economic development. Decreasing services trade restrictiveness has a positive indirect impact on the manufacturing sectors that use services as intermediate inputs in production. We identify a critical role of local institutions in shaping this effect: countries with high institutional capacity benefit the most from services trade policy reforms in...

  2. Simulation modeling for quality and productivity in steel cord manufacturing

    OpenAIRE

    Türkseven, Can Hulusi; Turkseven, Can Hulusi; Ertek, Gürdal; Ertek, Gurdal

    2003-01-01

    We describe the application of simulation modeling to estimate and improve quality and productivity performance of a steel cord manufacturing system. We describe the typical steel cord manufacturing plant, emphasize its distinguishing characteristics, identify various production settings and discuss applicability of simulation as a management decision support tool. Besides presenting the general structure of the developed simulation model, we focus on wire fractures, which can be an important...

  3. MANUFACTURING NATURAL KILLER CELLS AS MEDICINAL PRODUCTS

    Directory of Open Access Journals (Sweden)

    Christian CHABANNON

    2016-11-01

    Full Text Available Natural Killer (NK cells are Innate Lymphoid Cells (ILC with cytotoxic and regulatory properties. Their functions are tightly regulated by an array of inhibitory and activating receptors, and their mechanisms of activation strongly differ from antigen recognition in the context of HLA presentation as needed for T-cell activation. NK cells thus offer unique opportunities for new and improved therapeutic manipulation, either in vivo or in vitro, in a variety of human diseases, including cancers. NK cell activity can possibly be modulated in vivo through direct or indirect actions exerted by small molecules or monoclonal antibodies. NK cells can also be adoptively transferred following more or less substantial modifications through cell and gene manufacturing, in order to empower them with new or improved functions and ensure their controlled persistence and activity in the recipient. In the present review, we will focus on the technological and regulatory challenges of NK cell manufacturing, and discuss conditions in which these innovative cellular therapies can be brought to the clinic.

  4. Lean Production Applications in a Manufacturing Company

    Directory of Open Access Journals (Sweden)

    Ali Görener

    2016-01-01

    Full Text Available Lean production is a production model which comes about the pursuit of companies to be able to meet competition and make effective production. The main purpose of lean production is to get control about the wastage. This study includes the requirements for the success of the lean production and how the lean production system can be established. In this paper, lean production techniques were applied to the electric water heater line. Measurements using lean initiatives were made, operation cycle times were determined, and Kaizen improvement methods and line balancing methods were applied according to the results. And the last section of study showed conclusion of lean implementation.

  5. Good manufacturing practices of artisanal products in Northeastern Brazil

    Directory of Open Access Journals (Sweden)

    Medeiros, J.M.S.D

    2017-05-01

    Full Text Available This review provides an overview of the importance of good manufacturing practices in the elaboration of artisanal products, aiming to generate a discussion about this subject. The elaboration of artisanal food has been gaining prominence in several countries of the world since these products carry the identity and culture of a place. The traditional and artisanal way of manufacturing provides the food with a variation in its characteristics, which makes it peculiar in comparison to its similar, pleasing the most diverse demands of consumers. In addition, they are considered healthier and natural foods. In the Northeast of Brazil, these products are highlighted by the significant commercialization, being sources of income generation for the region. Among the most prominent products are the coalho and butter types cheeses, bottled butter and carne de sol. Despite the economic and cultural importance of these products, the traditional way of manufacturing, without proper hygiene care, can be a limiting factor for the formal commercialization of these products. Therefore, adopting good manufacturing practices at artisanal food processing places may be the first step towards the production of higher quality products that meet the requirements of the legislation but retain their artisanal manufacturing characteristics.

  6. 27 CFR 19.374 - Manufacture of nonbeverage products, intermediate products, or eligible flavors.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Manufacture of nonbeverage... PLANTS Processing Operations Other Than Denaturation and Manufacture of Articles Receipt and Use of Spirits, Wines and Alcoholic Flavoring Materials § 19.374 Manufacture of nonbeverage products...

  7. 76 FR 36078 - Milk for Manufacturing Purposes and Its Production and Processing; Requirements Recommended for...

    Science.gov (United States)

    2011-06-21

    ...] Milk for Manufacturing Purposes and Its Production and Processing; Requirements Recommended for... to quality and sanitation requirements for the production and processing of manufacturing grade milk... Manufacturing Purposes and Its Production and Processing; Recommended Requirements for Adoption by State...

  8. Problems and Instruments of Product and Technological Diversification of Manufacturing

    Directory of Open Access Journals (Sweden)

    Kuzmin Oleg Ye.

    2015-03-01

    Full Text Available The purpose of the article involves identification of objectives and development of instruments for product and technological diversification aimed at updating the range of products and introducing innovative technologies, which will ensure a high level of competitiveness and create preconditions for steady development of the enterprise. As a result of studying the literary sources the objectives and instruments for development of enterprises by means of product and technological diversification have been defined. The article suggests effective instruments of product and technological diversification of manufacturing, namely: the model of expansion of the product range, multi-criteria model of optimization of the product range, a modified model of Kantorovich-Koopmans for implementing new production technologies with set limits on the product output. Further research relate to formation of instruments for manufacturing diversification by means of introducing new types of production.

  9. BIOTECHNOLOGIES OF MEAT PRODUCTS MANUFACTURE. CURRENT STATE

    Directory of Open Access Journals (Sweden)

    Bal-Prilipko L. V.

    2014-10-01

    Full Text Available The analysis of literature and patents related to the possibilities of biotechnology for optimizing the domestic meat processing plants was the aim of the article. The analysis of the results of the use of biotechnological methods in the meat processing industry is given. The prospects for their implementation are evaluated. The main development strategy of technological meat processing to develop the methods of obtaining high quality and safe meat products is highlighted. Targeted use of special strains of microorganisms in production of functional meat products offers some opportunities. Thus, such action is associated with formation of the following specific dietary components: organic acids, bactericins, enzymes, vitamins and others. They promote to improve the sanitary microbiological, organoleptic, functional and technological parameters of meat products. Using of denitrifying microbial strains could reduce the residual content of sodium nitrite in the finished product, minimizing the possible carcinogenic and mutagenic impact of this compound on a human body, producing functional safe products while maintaining its high organoleptic characteristics.

  10. Optimization of large scale food production using Lean Manufacturing principles

    DEFF Research Database (Denmark)

    Engelund, Eva Høy; Friis, Alan; Breum, Gitte

    2009-01-01

    This paper discusses how the production principles of Lean Manufacturing (Lean) can be applied in a large-scale meal production. Lean principles are briefly presented, followed by a field study of how a kitchen at a Danish hospital has implemented Lean in the daily production. In the kitchen...... not be negatively affected by the rationalisation of production procedures. The field study shows that Lean principles can be applied in meal production and can result in increased production efficiency and systematic improvement of product quality without negative effects on the working environment. The results...... show that Lean can be applied and used to manage the production of meals in the kitchen....

  11. Manufacturing economics of plant-made biologics: case studies in therapeutic and industrial enzymes.

    Science.gov (United States)

    Tusé, Daniel; Tu, Tiffany; McDonald, Karen A

    2014-01-01

    Production of recombinant biologics in plants has received considerable attention as an alternative platform to traditional microbial and animal cell culture. Industrially relevant features of plant systems include proper eukaryotic protein processing, inherent safety due to lack of adventitious agents, more facile scalability, faster production (transient systems), and potentially lower costs. Lower manufacturing cost has been widely claimed as an intuitive feature of the platform by the plant-made biologics community, even though cost information resides within a few private companies and studies accurately documenting such an advantage have been lacking. We present two technoeconomic case studies representing plant-made enzymes for diverse applications: human butyrylcholinesterase produced indoors for use as a medical countermeasure and cellulases produced in the field for the conversion of cellulosic biomass into ethanol as a fuel extender. Production economics were modeled based on results reported with the latest-generation expression technologies on Nicotiana host plants. We evaluated process unit operations and calculated bulk active and per-dose or per-unit costs using SuperPro Designer modeling software. Our analyses indicate that substantial cost advantages over alternative platforms can be achieved with plant systems, but these advantages are molecule/product-specific and depend on the relative cost-efficiencies of alternative sources of the same product.

  12. Manufacturing Economics of Plant-Made Biologics: Case Studies in Therapeutic and Industrial Enzymes

    Directory of Open Access Journals (Sweden)

    Daniel Tusé

    2014-01-01

    Full Text Available Production of recombinant biologics in plants has received considerable attention as an alternative platform to traditional microbial and animal cell culture. Industrially relevant features of plant systems include proper eukaryotic protein processing, inherent safety due to lack of adventitious agents, more facile scalability, faster production (transient systems, and potentially lower costs. Lower manufacturing cost has been widely claimed as an intuitive feature of the platform by the plant-made biologics community, even though cost information resides within a few private companies and studies accurately documenting such an advantage have been lacking. We present two technoeconomic case studies representing plant-made enzymes for diverse applications: human butyrylcholinesterase produced indoors for use as a medical countermeasure and cellulases produced in the field for the conversion of cellulosic biomass into ethanol as a fuel extender. Production economics were modeled based on results reported with the latest-generation expression technologies on Nicotiana host plants. We evaluated process unit operations and calculated bulk active and per-dose or per-unit costs using SuperPro Designer modeling software. Our analyses indicate that substantial cost advantages over alternative platforms can be achieved with plant systems, but these advantages are molecule/product-specific and depend on the relative cost-efficiencies of alternative sources of the same product.

  13. Integrated Production-Distribution Scheduling Problem with Multiple Independent Manufacturers

    Directory of Open Access Journals (Sweden)

    Jianhong Hao

    2015-01-01

    Full Text Available We consider the nonstandard parts supply chain with a public service platform for machinery integration in China. The platform assigns orders placed by a machinery enterprise to multiple independent manufacturers who produce nonstandard parts and makes production schedule and batch delivery schedule for each manufacturer in a coordinate manner. Each manufacturer has only one plant with parallel machines and is located at a location far away from other manufacturers. Orders are first processed at the plants and then directly shipped from the plants to the enterprise in order to be finished before a given deadline. We study the above integrated production-distribution scheduling problem with multiple manufacturers to maximize a weight sum of the profit of each manufacturer under the constraints that all orders are finished before the deadline and the profit of each manufacturer is not negative. According to the optimal condition analysis, we formulate the problem as a mixed integer programming model and use CPLEX to solve it.

  14. Social aspects in additive manufacturing of pharmaceutical products

    DEFF Research Database (Denmark)

    Lind, Johanna Lena Maria; Kälvemark Sporrong, Sofia; Kaae, Susanne

    2016-01-01

    INTRODUCTION: Additive manufacturing (AM) techniques, such as drug printing, represent a new engineering approach that can implement the concept of personalized medicine via on-demand manufacturing of dosage forms with individually adjusted doses. Implementation of AM principles...... will be used for production of on-demand medicine. The impact of such changes in the distribution chain on regulation, healthcare professionals and patients are highlighted. Expert opinion: Drug manufacturing by traditional methods is well-established, but it lacks the possibility for on-demand personalized...

  15. Productivity and Openness: Firm Level Evidence in Brazilian Manufacturing Industries

    OpenAIRE

    Wenjun Liu; Shoji Nishijima

    2012-01-01

    This study investigates the productivity of Brazilian manufacturing industries, particularly addressing the influence of liberalization on productivity. We first calculate total factor productivity (TFP) by estimating the stochastic frontier production function and the inefficiency determination equation simultaneously. Then TFP growth rates are regressed on openness-related variables and other firm characteristics. The results show that firm openness to the world is a crucial determinant of ...

  16. Recent advances in fuel product and manufacturing process development

    International Nuclear Information System (INIS)

    Slember, R.J.; Doshi, P.K.

    1987-01-01

    This paper discusses advancements in commercial nuclear fuel products and manufacturing made by the Westinghouse Electric Corporation in response to the commercial nuclear fuel industry's demand for high reliability, increased plant availability and improved operating flexibility. The features and benefits of Westinghouse's most advanced fuel products--VANTAGE 5 for PWR plants and QUAD+ for BWR plants--are described, as well as 'high performance' fuel concepts now under development for delivery in the late 1980s. The paper also disusses the importance of in-process quality control throughout manufacturing towards reducing product variability and improving fuel reliability. (author)

  17. A Single-use Strategy to Enable Manufacturing of Affordable Biologics

    OpenAIRE

    Jacquemart, Renaud; Vandersluis, Melissa; Zhao, Mochao; Sukhija, Karan; Sidhu, Navneet; Stout, Jim

    2016-01-01

    The current processing paradigm of large manufacturing facilities dedicated to single product production is no longer an effective approach for best manufacturing practices. Increasing competition for new indications and the launch of biosimilars for the monoclonal antibody market have put pressure on manufacturers to produce at lower cost. Single-use technologies and continuous upstream processes have proven to be cost-efficient options to increase biomass production but as of today the adop...

  18. From a homemade to an industrial product : manufacturing Bulgarian yogurt

    NARCIS (Netherlands)

    Stoilova, E.R.

    2013-01-01

    Changes in yogurt production in the first half of the twentieth century were related to the transformation of dairy manufacturing through the incorporation of science and technology into the production process. The modernization of the dairy industry affected yogurt, which Bulgarians considered a

  19. Horizontally Differentiated Store Brands: Production Outsourcing to National Brand Manufacturers

    Directory of Open Access Journals (Sweden)

    Shun Shindo

    2014-01-01

    Full Text Available We study a retailer's strategic decision with regard to outsourcing the production of such types of store brands (SBs to national brand (NB manufacturers. The wholesale price of NB is assumed to be set by the manufacturer, while that of the SB is assumed to be set by the retailer. When a retailer outsources SB production to an NB manufacturer, the NB manufacturer might suffer from cannibalization due to offering both the SB and the NB, implying that a strategic interaction between the retailer and manufacturer is an important issue. Based on this motivation, we mainly focus on the strategy of a dominant retailer in such a situation and investigate it with a game-theoretic approach. We show that the optimal strategy for the SB retailer sensitively depends on the degree of differentiation between the SB and the NB. In particular, if both products are less differentiated, the retailer benefits from offering only the SB, and, in this case, the retailer should offer its wholesale price, after the manufacturer sets the NB wholesale price. Furthermore, it is shown that the optimal strategies of the retailer are socially efficient, if and only if the SB and the NB are sufficiently differentiated.

  20. The yeast stands alone: the future of protein biologic production.

    Science.gov (United States)

    Love, Kerry R; Dalvie, Neil C; Love, J Christopher

    2017-12-22

    Yeasts are promising alternative hosts for the manufacturing of recombinant protein therapeutics because they simply and efficiently meet needs for both platform and small-market drugs. Fast accumulation of biomass and low-cost media reduce the cost-of-goods when using yeast, which in turn can enable agile, small-volume manufacturing facilities. Small, tractable yeast genomes are amenable to rapid process development, facilitating strain and product quality by design. Specifically, Pichia pastoris is becoming a widely accepted yeast for biopharmaceutical manufacturing in much of the world owing to a clean secreted product and the rapidly expanding understanding of its cell biology as a host organism. We advocate for a near term partnership spanning industry and academia to promote open source, timely development of yeast hosts. Copyright © 2017. Published by Elsevier Ltd.

  1. BIOTECHNOLOGIES OF MEAT PRODUCTS MANUFACTURE. CURRENT STATE

    OpenAIRE

    Bal-Prilipko L. V.; Leonova B. I.

    2014-01-01

    The analysis of literature and patents related to the possibilities of biotechnology for optimizing the domestic meat processing plants was the aim of the article. The analysis of the results of the use of biotechnological methods in the meat processing industry is given. The prospects for their implementation are evaluated. The main development strategy of technological meat processing to develop the methods of obtaining high quality and safe meat products is highlighted. Targeted use of spe...

  2. Product Life Cycle of the Manufactured Home Industry

    Directory of Open Access Journals (Sweden)

    Gavin Wherry

    2014-09-01

    Full Text Available Residential construction consumes an estimated 26 percent of the total U.S. wood harvest and thus plays an important role in the forest products value chain. While being a relatively small part of the U.S. residential construction market, the factory-built residential housing industry, originating from manufactured homes (e.g. mobile homes, is embracing emerging industry segments such as modular or panelized homes. Since indications exist that factory-built home production is slated to gain a more prominent role in the U.S. construction markets at the cost of traditional stick-built production, the factory-built home industry sub-segment is of considerable importance to the forest products industry. This research looks at manufactured home producers as a benchmark for analyzing the current economic state of the industry and discusses competitive strategies. The analysis concludes, through macroeconomic modeling, that manufactured homes are in the declining stage of their product life cycle due to changes to the U.S. residential construction sector and the factory-built home industry and by advancements of rival industry-segments. As market share continues to decline, firms operating in this industry-segment seek to either hedge their losses through product diversification strategies or remain focused on strategically repositioning the manufactured home segment.

  3. 75 FR 61418 - Milk for Manufacturing Purposes and Its Production and Processing; Requirements Recommended for...

    Science.gov (United States)

    2010-10-05

    ... for Manufacturing Purposes and Its Production and Processing; Requirements Recommended for Adoption by... sanitation requirements for the production and processing of manufacturing grade milk. These Recommended... comments. SUMMARY: This document proposes to amend the recommended manufacturing milk requirements...

  4. Method of manufacturing borosilicate glass solidification products

    International Nuclear Information System (INIS)

    Tanaka, Tsuneya.

    1986-01-01

    Purpose: To obtain glass solidification products efficiently in a dry process from medium and high level radioactive liquid wastes discharged from PWR type reactors. Method: Boric acid-containing radioactive liquid wastes generated from primary coolants of PWR type reactors are evaporated to condensate as the pre-treatment. The concentrated liquid wastes are supplied to a drum type rotary kiln. While on the other hand, usual glass frits are introduced into the kiln. The liquid wastes are dried in the rotary kiln, as well as B 2 O 3 and the glass frits in the liquid wastes are combined into glass particles. In this case, since the kiln is rotated, no glass particles are deposited on the wall of the kiln. Then, the glass particles are introduced for melting into a high frequency melting furnace made of metal. The melting temperature is set to 1100 - 1150 deg C. The molten borosilicate glass is recovered from the bottom of the melting furance, contained in a canister and cooled for several hours, and then a cover is welded to the canister. (Ikeda, J.)

  5. Modelling energy consumption in a manufacturing plant using productivity KPIs

    Energy Technology Data Exchange (ETDEWEB)

    Gallachoir, Brian O.; Cahill, Caiman (Sustainable Energy Research Group, Dept. of Civil and Environmental Engineering, Univ. College Cork (Ireland))

    2009-07-01

    Energy efficiency initiatives in industrial plants are often focused on getting energy-consuming utilities and devices to operate more efficiently, or on conserving energy. While such device-oriented energy efficiency measures can achieve considerable savings, greater energy efficiency improvement may be achieved by improving the overall productivity and quality of manufacturing processes. The paper highlights the observed relationship between productivity and energy efficiency using aggregated data on unit consumption and production index data for Irish industry. Past studies have developed simple top-down models of final energy consumption in manufacturing plants using energy consumption and production output figures, but these models do not help identify opportunities for energy savings that could achieved through increased productivity. This paper proposes an improved and innovative method of modelling plant final energy demand that introduces standard productivity Key Performance Indicators (KPIs) into the model. The model demonstrates the relationship between energy consumption and productivity, and uses standard productivity metrics to identify the areas of manufacturing activity that offer the most potential for improved energy efficiency. The model provides a means of comparing the effect of device-oriented energy efficiency measures with the potential for improved energy efficiency through increased productivity.

  6. FDA 101: Regulating Biological Products

    Science.gov (United States)

    ... based and cellular biologics, at the forefront of biomedical research today, may make it possible to treat a ... transplantation vaccines The Center for Drug Evaluation and Research ... as targeted therapies in cancer and other diseases cytokines (types of ...

  7. Efficacy of Lean Manufacturing to Improve Production Performance

    Directory of Open Access Journals (Sweden)

    Israel Balogun

    2016-12-01

    Full Text Available The lean manufacturing system is a technique of manufacturing products in time. The concept of lean manufacturing principles employs simpler ways of communicating required materials as well as manual technique in ensuring the provision of signals for replenishment of materials the production companies require. Performance on the other hand, can be considered the attainment of value effectively and efficiently. Lean manufacturing and performance production goes hand in hand. Through utilizing lean manufacturing method, most companies would be able to tailor their processes in achieving effective performance and meeting unique requests from their consumers. The exploratory observations conducted in the study was purposely for examining the nature of complex interactions involved between major constructs and environmental sustainability at the parent company and the tire part vendors. The method of the research was a qualitative case study. The research data were obtained from with the case company and through structured interviews the case company's consumers. The case-specific tools were first developed in close co-operation with the case company. Future research agenda addresses gaps in the current literature and suggests relevant framework from which to explore this phenomenon.

  8. Post Processing Methods used to Improve Surface Finish of Products which are Manufactured by Additive Manufacturing Technologies: A Review

    Science.gov (United States)

    Kumbhar, N. N.; Mulay, A. V.

    2016-08-01

    The Additive Manufacturing (AM) processes open the possibility to go directly from Computer-Aided Design (CAD) to a physical prototype. These prototypes are used as test models before it is finalized as well as sometimes as a final product. Additive Manufacturing has many advantages over the traditional process used to develop a product such as allowing early customer involvement in product development, complex shape generation and also save time as well as money. Additive manufacturing also possess some special challenges that are usually worth overcoming such as Poor Surface quality, Physical Properties and use of specific raw material for manufacturing. To improve the surface quality several attempts had been made by controlling various process parameters of Additive manufacturing and also applying different post processing techniques on components manufactured by Additive manufacturing. The main objective of this work is to document an extensive literature review in the general area of post processing techniques which are used in Additive manufacturing.

  9. 77 FR 42319 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2012-07-18

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug...: Vaccines and Related Biological Products Advisory Committee. General Function of the Committee: To provide... consideration of the appropriateness of cell lines derived from human tumors for vaccine manufacture. FDA...

  10. 77 FR 63839 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2012-10-17

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug...: Vaccines and Related Biological Products Advisory Committee. General Function of the Committee: To provide...) Virus Monovalent Vaccine manufactured by GlaxoSmithKline. On November 15, 2012, the committee will meet...

  11. Good manufacturing practices for medicinal products for human use.

    Science.gov (United States)

    Gouveia, Bruno G; Rijo, Patrícia; Gonçalo, Tânia S; Reis, Catarina P

    2015-01-01

    At international and national levels, there are public and private organizations, institutions and regulatory authorities, who work and cooperate between them and with Pharmaceutical Industry, in order to achieve a consensus of the guidelines and laws of the manufacturing of medicinal products for human use. This article includes an explanation of how operate and cooperate these participants, between them and expose the current regulations, following the line of European Community/European Economic Area, referencing, wherever appropriate, the practiced guidelines, outside of regulatory action of space mentioned. In this way, it is intended to achieve quality, security and effectiveness exceptional levels in the manufacturing of health products. Good Manufacturing Practice aim the promotion of the human health and consequently, to the improvement of quality of life. For achieve the proposed objectives, it is necessary to ensure the applicability of the presented concepts and show the benefits arising from this applicability.

  12. Good manufacturing practices for medicinal products for human use

    Science.gov (United States)

    Gouveia, Bruno G.; Rijo, Patrícia; Gonçalo, Tânia S.; Reis, Catarina P.

    2015-01-01

    At international and national levels, there are public and private organizations, institutions and regulatory authorities, who work and cooperate between them and with Pharmaceutical Industry, in order to achieve a consensus of the guidelines and laws of the manufacturing of medicinal products for human use. This article includes an explanation of how operate and cooperate these participants, between them and expose the current regulations, following the line of European Community/European Economic Area, referencing, wherever appropriate, the practiced guidelines, outside of regulatory action of space mentioned. In this way, it is intended to achieve quality, security and effectiveness exceptional levels in the manufacturing of health products. Good Manufacturing Practice aim the promotion of the human health and consequently, to the improvement of quality of life. For achieve the proposed objectives, it is necessary to ensure the applicability of the presented concepts and show the benefits arising from this applicability. PMID:25883511

  13. Mining manufacturing data for discovery of high productivity process characteristics.

    Science.gov (United States)

    Charaniya, Salim; Le, Huong; Rangwala, Huzefa; Mills, Keri; Johnson, Kevin; Karypis, George; Hu, Wei-Shou

    2010-06-01

    Modern manufacturing facilities for bioproducts are highly automated with advanced process monitoring and data archiving systems. The time dynamics of hundreds of process parameters and outcome variables over a large number of production runs are archived in the data warehouse. This vast amount of data is a vital resource to comprehend the complex characteristics of bioprocesses and enhance production robustness. Cell culture process data from 108 'trains' comprising production as well as inoculum bioreactors from Genentech's manufacturing facility were investigated. Each run constitutes over one-hundred on-line and off-line temporal parameters. A kernel-based approach combined with a maximum margin-based support vector regression algorithm was used to integrate all the process parameters and develop predictive models for a key cell culture performance parameter. The model was also used to identify and rank process parameters according to their relevance in predicting process outcome. Evaluation of cell culture stage-specific models indicates that production performance can be reliably predicted days prior to harvest. Strong associations between several temporal parameters at various manufacturing stages and final process outcome were uncovered. This model-based data mining represents an important step forward in establishing a process data-driven knowledge discovery in bioprocesses. Implementation of this methodology on the manufacturing floor can facilitate a real-time decision making process and thereby improve the robustness of large scale bioprocesses. 2010 Elsevier B.V. All rights reserved.

  14. Multi-objective evolutionary optimisation for product design and manufacturing

    CERN Document Server

    2011-01-01

    Presents state-of-the-art research in the area of multi-objective evolutionary optimisation for integrated product design and manufacturing Provides a comprehensive review of the literature Gives in-depth descriptions of recently developed innovative and novel methodologies, algorithms and systems in the area of modelling, simulation and optimisation

  15. Product costing guide for wood dimension and component manufacturers

    Science.gov (United States)

    Adrienn Andersch; Urs Buehlmann; Jeff Palmer; Janice K. Wiedenbeck; Steve. Lawser

    2014-01-01

    The North American hardwood dimension and components industry plays a critical role in the hardwood forest products industry as the industry is a user of high-value hardwood lumber. Customer expectations, global markets, and international competition, however, require hardwood dimension and components manufacturers to continuously improve their ability to manage their...

  16. Productivity growth patterns in US dairy products manufacturing plants

    NARCIS (Netherlands)

    Geylani, P.C.; Stefanou, S.E.

    2011-01-01

    We analyse the productivity growth patterns in the US dairy products industry using the Census Bureau's plant-level data set. We decompose Total Factor Productivity (TFP) growth into the scale and technical change components and analyse variability of plants' productivity by constructing transition

  17. High Volume Manufacturing and Field Stability of MEMS Products

    Science.gov (United States)

    Martin, Jack

    Low volume MEMS/NEMS production is practical when an attractive concept is implemented with business, manufacturing, packaging, and test support. Moving beyond this to high volume production adds requirements on design, process control, quality, product stability, market size, market maturity, capital investment, and business systems. In a broad sense, this chapter uses a case study approach: It describes and compares the silicon-based MEMS accelerometers, pressure sensors, image projection systems, and gyroscopes that are in high volume production. Although they serve several markets, these businesses have common characteristics. For example, the manufacturing lines use automated semiconductor equipment and standard material sets to make consistent products in large quantities. Standard, well controlled processes are sometimes modified for a MEMS product. However, novel processes that cannot run with standard equipment and material sets are avoided when possible. This reliance on semiconductor tools, as well as the organizational practices required to manufacture clean, particle-free products partially explains why the MEMS market leaders are integrated circuit manufacturers. There are other factors. MEMS and NEMS are enabling technologies, so it can take several years for high volume applications to develop. Indeed, market size is usually a strong function of price. This becomes a vicious circle, because low price requires low cost - a result that is normally achieved only after a product is in high volume production. During the early years, IC companies reduced cost and financial risk by using existing facilities for low volume MEMS production. As a result, product architectures are partially determined by capabilities developed for previous products. This chapter includes a discussion of MEMS product architecture with particular attention to the impact of electronic integration, packaging, and surfaces. Packaging and testing are critical, because they are

  18. Continuous downstream processing for high value biological products: A Review.

    Science.gov (United States)

    Zydney, Andrew L

    2016-03-01

    There is growing interest in the possibility of developing truly continuous processes for the large-scale production of high value biological products. Continuous processing has the potential to provide significant reductions in cost and facility size while improving product quality and facilitating the design of flexible multi-product manufacturing facilities. This paper reviews the current state-of-the-art in separations technology suitable for continuous downstream bioprocessing, focusing on unit operations that would be most appropriate for the production of secreted proteins like monoclonal antibodies. This includes cell separation/recycle from the perfusion bioreactor, initial product recovery (capture), product purification (polishing), and formulation. Of particular importance are the available options, and alternatives, for continuous chromatographic separations. Although there are still significant challenges in developing integrated continuous bioprocesses, recent technological advances have provided process developers with a number of attractive options for development of truly continuous bioprocessing operations. © 2015 Wiley Periodicals, Inc.

  19. Operator-Oriented Product and Production Process Design for Manufacturing, Maintenance and Upgrading

    NARCIS (Netherlands)

    Rhijn, G. van; Bosch, T.

    2017-01-01

    The nature of production in the manufacturing industry is changing, and companies face large challenges. Customers expect fast delivery times, proven sustainability, flexibility, and frequent product upgrades. To stay competitive and manage rapid technological demands, a parallel, iterative and

  20. Synthetic biology for manufacturing chemicals: constraints drive the use of non-conventional microbial platforms.

    Science.gov (United States)

    Czajka, Jeffrey; Wang, Qinhong; Wang, Yechun; Tang, Yinjie J

    2017-10-01

    Genetically modified microbes have had much industrial success producing protein-based products (such as antibodies and enzymes). However, engineering microbial workhorses for biomanufacturing of commodity compounds remains challenging. First, microbes cannot afford burdens with both overexpression of multiple enzymes and metabolite drainage for product synthesis. Second, synthetic circuits and introduced heterologous pathways are not yet as "robust and reliable" as native pathways due to hosts' innate regulations, especially under suboptimal fermentation conditions. Third, engineered enzymes may lack channeling capabilities for cascade-like transport of metabolites to overcome diffusion barriers or to avoid intermediate toxicity in the cytoplasmic environment. Fourth, moving engineered hosts from laboratory to industry is unreliable because genetic mutations and non-genetic cell-to-cell variations impair the large-scale fermentation outcomes. Therefore, synthetic biology strains often have unsatisfactory industrial performance (titer/yield/productivity). To overcome these problems, many different species are being explored for their metabolic strengths that can be leveraged to synthesize specific compounds. Here, we provide examples of non-conventional and genetically amenable species for industrial manufacturing, including the following: Corynebacterium glutamicum for its TCA cycle-derived biosynthesis, Yarrowia lipolytica for its biosynthesis of fatty acids and carotenoids, cyanobacteria for photosynthetic production from its sugar phosphate pathways, and Rhodococcus for its ability to biotransform recalcitrant feedstock. Finally, we discuss emerging technologies (e.g., genome-to-phenome mapping, single cell methods, and knowledge engineering) that may facilitate the development of novel cell factories.

  1. Implementation of Canflex bundle manufacture - from 'bench scale' to production

    International Nuclear Information System (INIS)

    Pant, A.

    1999-01-01

    Zircatec Precision Industries (ZPI) has been involved with the development of the 43 element Canflex bundle design since 1986. This development included several 'prototype' campaigns involving the manufacture of small quantities of test bundles using enriched fuel. Manufacturing and inspection methods for this fuel were developed at ZPI as the design progressed. The most recent campaign involved the production of 26 bundles of the final Canflex design for a demonstration irradiation in the Point Lepreau Generating Station. This presentation will explore issues pertaining to the introduction of a new product line from initial trial quantities to full production levels. The Canflex fuel experience and a brief review of development efforts will be used as an example. (author)

  2. 46 CFR 50.25-5 - Products requiring manufacturer or mill certification.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Products requiring manufacturer or mill certification... manufacturer or mill certification. (a) Products required to be certified by a manufacturer or by mill... accepted without referring to its manufacturer or mill certification, if: (1) The product is marked in...

  3. Synthetic biology advances for pharmaceutical production

    OpenAIRE

    Breitling, Rainer; Takano, Eriko

    2015-01-01

    Synthetic biology enables a new generation of microbial engineering for the biotechnological production of pharmaceuticals and other high-value chemicals. This review presents an overview of recent advances in the field, describing new computational and experimental tools for the discovery, optimization and production of bioactive molecules, and outlining progress towards the application of these tools to pharmaceutical production systems.

  4. Synthetic biology advances for pharmaceutical production

    Science.gov (United States)

    Breitling, Rainer; Takano, Eriko

    2015-01-01

    Synthetic biology enables a new generation of microbial engineering for the biotechnological production of pharmaceuticals and other high-value chemicals. This review presents an overview of recent advances in the field, describing new computational and experimental tools for the discovery, optimization and production of bioactive molecules, and outlining progress towards the application of these tools to pharmaceutical production systems. PMID:25744872

  5. Product variety, product complexity and manufacturing operational performance: A systematic literature review

    DEFF Research Database (Denmark)

    Trattner, Alexandria Lee; Hvam, Lars; Herbert-Hansen, Zaza Nadja Lee

    Manufacturing in the twenty-first century has been wrought with the struggle to satisfy the rising demand for greater product variety and more complex products while still maintaining efficient manufacturing operations. However, the literature lacks an overview of which operational performance...... measures are most affected by increased variety and complexity. This study presents a systematic literature review of the recent scholarly literature on variety, complexity and manufacturing operational performance (MOP). Results show that product variety has a consistently negative relationship with MOP...... across different time, cost, quality and flexibility measures while product complexity lacks evidence of strong relationships with MOP measures....

  6. Design control considerations for biologic-device combination products.

    Science.gov (United States)

    Anderson, Dave; Liu, Roger; Anand Subramony, J; Cammack, Jon

    2017-03-01

    Combination products are therapeutic and diagnostic medical products that combine drugs, devices, and/or biological products with one another. Historically, biologics development involved identifying efficacious doses administered to patients intravenously or perhaps by a syringe. Until fairly recently, there has been limited focus on developing an accompanying medical device, such as a prefilled syringe or auto-injector, to enable easy and more efficient delivery. For the last several years, and looking forward, where there may be little to distinguish biologics medicines with relatively similar efficacy profiles, the biotechnology market is beginning to differentiate products by patient-focused, biologic-device based combination products. As innovative as biologic-device combination products are, they can pose considerable development, regulatory, and commercialization challenges due to unique physicochemical properties and special clinical considerations (e.g., dosing volumes, frequency, co-medications, etc.) of the biologic medicine. A biologic-device combination product is a marriage between two partners with "cultural differences," so to speak. There are clear differences in the development, review, and commercialization processes of the biologic and the device. When these two cultures come together in a combination product, developers and reviewers must find ways to address the design controls and risk management processes of both the biologic and device, and knit them into a single entity with supporting product approval documentation. Moreover, digital medicine and connected health trends are pushing the boundaries of combination product development and regulations even further. Despite an admirable cooperation between industry and FDA in recent years, unique product configurations and design features have resulted in review challenges. These challenges have prompted agency reviewers to modernize consultation processes, while at the same time, promoting

  7. Lean production teams and health in garment manufacture.

    Science.gov (United States)

    Jackson, P R; Mullarkey, S

    2000-04-01

    The impact of lean production on psychological health was assessed by comparing lean production teams in garment manufacture with a traditional system for making similar garments. Work design characteristics were examined as mediators of the impact of work organization on health. Findings indicate both positive and negative direct effects of teamworking on aspects of autonomy, work demands, and social climate. In turn, both positive and negative direct effects of work design on psychological health were found, which combine to give no overall difference between the groups. This study suggests that the balance between positive and negative effects of lean production teamworking depends on management choices in the form of work design.

  8. The production route selection algorithm in virtual manufacturing networks

    Science.gov (United States)

    Krenczyk, D.; Skolud, B.; Olender, M.

    2017-08-01

    The increasing requirements and competition in the global market are challenges for the companies profitability in production and supply chain management. This situation became the basis for construction of virtual organizations, which are created in response to temporary needs. The problem of the production flow planning in virtual manufacturing networks is considered. In the paper the algorithm of the production route selection from the set of admissible routes, which meets the technology and resource requirements and in the context of the criterion of minimum cost is proposed.

  9. Emissions from laboratory combustor tests of manufactured wood products

    Energy Technology Data Exchange (ETDEWEB)

    Wilkening, R.; Evans, M.; Ragland, K. [Univ. of Wisconsin, Madison, WI (United States); Baker, A. [USDA Forest Products Lab., Madison, WI (United States)

    1993-12-31

    Manufactured wood products contain wood, wood fiber, and materials added during manufacture of the product. Manufacturing residues and the used products are burned in a furnace or boiler instead of landfilling. Emissions from combustion of these products contain additional compounds from the combustion of non-wood material which have not been adequately characterized to specify the best combustion conditions, emissions control equipment, and disposal procedures. Total hydrocarbons, formaldehyde, higher aldehydes and carbon monoxide emissions from aspen flakeboard and aspen cubes were measured in a 76 mm i.d. by 1.5 m long fixed bed combustor as a function of excess oxygen, and temperature. Emissions of hydrocarbons, aldehydes and CO from flakeboard and from clean aspen were very sensitive to average combustor temperature and excess oxygen. Hydrocarbon and aldehyde emissions below 10 ppM were achieved with 5% excess oxygen and 1,200{degrees}C average temperature for aspen flakeboard and 1,100{degrees}C for clean aspen at a 0.9 s residence time. When the average temperature decreased below these levels, the emissions increased rapidly. For example, at 950{degrees}C and 5% excess oxygen the formaldehyde emissions were over 1,000 ppM. These laboratory tests reinforce the need to carefully control the temperature and excess oxygen in full-scale wood combustors.

  10. Distributed Manufacturing of Flexible Products: Technical Feasibility and Economic Viability

    Directory of Open Access Journals (Sweden)

    Aubrey L. Woern

    2017-10-01

    Full Text Available Distributed manufacturing even at the household level is now well established with the combined use of open source designs and self-replicating rapid prototyper (RepRap 3-D printers. Previous work has shown substantial economic consumer benefits for producing their own polymer products. Now flexible filaments are available at roughly 3-times the cost of more conventional 3-D printing materials. To provide some insight into the potential for flexible filament to be both technically feasible and economically viable for distributed digital manufacturing at the consumer level this study investigates 20 common flexible household products. The 3-D printed products were quantified by print time, electrical energy use and filament consumption by mass to determine the cost to fabricate with a commercial RepRap 3-D printer. Printed parts were inspected and when necessary tested for their targeted application to ensure technical feasibility. Then, the experimentally measured cost to DIY manufacturers was compared to low and high market prices for comparable commercially available products. In addition, the mark-up and potential for long-term price declines was estimated for flexible filaments by converting thermoplastic elastomer (TPE pellets into filament and reground TPE from a local recycling center into filament using an open source recyclebot. This study found that commercial flexible filament is economically as well as technically feasible for providing a means of distributed home-scale manufacturing of flexible products. The results found a 75% savings when compared to the least expensive commercially equivalent products and 92% when compared to high market priced products. Roughly, 160 flexible objects must be substituted to recover the capital costs to print flexible materials. However, as previous work has shown the Lulzbot Mini 3-D printer used in this study would provide more than a 100% ROI printing one object a week from hard thermoplastics

  11. Mitigating the risk of Zika virus contamination of raw materials and cell lines in the manufacture of biologicals.

    Science.gov (United States)

    Zmurko, Joanna; Vasey, Douglas B; Donald, Claire L; Armstrong, Alison A; McKee, Marian L; Kohl, Alain; Clayton, Reginald F

    2018-02-01

    Ensuring the virological safety of biologicals is challenging due to the risk of viral contamination of raw materials and cell banks, and exposure during in-process handling to known and/or emerging viral pathogens. Viruses may contaminate raw materials and biologicals intended for human or veterinary use and remain undetected until appropriate testing measures are employed. The outbreak and expansive spread of the mosquito-borne flavivirus Zika virus (ZIKV) poses challenges to screening human- and animal -derived products used in the manufacture of biologicals. Here, we report the results of an in vitro study where detector cell lines were challenged with African and Asian lineages of ZIKV. We demonstrate that this pathogen is robustly detectable by in vitro assay, thereby providing assurance of detection of ZIKV, and in turn underpinning the robustness of in vitro virology assays in safety testing of biologicals.

  12. Isotope products manufacture in Russia and its prospects

    International Nuclear Information System (INIS)

    Malyshev, S.V.; Okhotina, I.A.; Kalelin, E.A.; Krasnov, N.N.; Kuzin, V.V.; Malykh, J.A.; Makarovsky, S.B.

    1997-01-01

    At the present stage of the world economy development, stable and radioactive isotopes,preparations and products on their base are widely used in many fields of the national economy, medicine and scientific researches. The Russian Federation is one of the largest worldwide producers of a variety of nuclide products on the base of more than 350 isotopes, as follows: stable isotopes reactor, cyclotron, fission product radioactive isotopes, ion-radiation sources compounds, labelled with stable and radioactive isotopes, radionuclide short-lived isotope generators, radiopharmaceuticals, radionuclide light and heat sources; luminous paints on base of isotopes. The Russian Ministry for Atomic Energy coordinates activity for development and organization of manufacture and isotope products supply in Russia as well as for export. Within many years of isotope industry development, there have appeared some manufacturing centres in Russia, dealing with a variety of isotope products. The report presents the production potentialities of these centres and also an outlook on isotope production development in Russia in the next years

  13. Additive manufacturing of metals the technology, materials, design and production

    CERN Document Server

    Yang, Li; Baughman, Brian; Godfrey, Donald; Medina, Francisco; Menon, Mamballykalathil; Wiener, Soeren

    2017-01-01

    This book offers a unique guide to the three-dimensional (3D) printing of metals. It covers various aspects of additive, subtractive, and joining processes used to form three-dimensional parts with applications ranging from prototyping to production. Examining a variety of manufacturing technologies and their ability to produce both prototypes and functional production-quality parts, the individual chapters address metal components and discuss some of the important research challenges associated with the use of these technologies. As well as exploring the latest technologies currently under development, the book features unique sections on electron beam melting technology, material lifting, and the importance this science has in the engineering context. Presenting unique real-life case studies from industry, this book is also the first to offer the perspective of engineers who work in the field of aerospace and transportation systems, and who design components and manufacturing networks. Written by the leadin...

  14. International Outsourcing and Productivity in Italian Manufacturing Sectors

    OpenAIRE

    Lo Turco Alessia

    2007-01-01

    This paper estimates the effect of international outsourcing of materials and services on productivity in Italian manufacturing sectors during the period 1985-1997. Three different measures of outsourcing are used. Firstly, a "narrow" measure of outsourcing is calculated as the intensity of intermediate inputs that each sector imports from the same sector abroad. Secondly, a "broad" measure of outsourcing of materials is calculated as the intensity of materials imported from non-energy manufa...

  15. Biological production of organic compounds

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Jianping; Paddock, Troy; Carrieri, Damian; Maness, Pin-Ching; Seibert, Michael

    2016-04-12

    Strains of cyanobacteria that produce high levels of alpha ketoglutarate (AKG) and pyruvate are disclosed herein. Methods of culturing these cyanobacteria to produce AKG or pyruvate and recover AKG or pyruvate from the culture are also described herein. Nucleic acid sequences encoding polypeptides that function as ethylene-forming enzymes and their use in the production of ethylene are further disclosed herein. These nucleic acids may be expressed in hosts such as cyanobacteria, which in turn may be cultured to produce ethylene.

  16. Approaches to Quality Risk Management When Using Single-Use Systems in the Manufacture of Biologics.

    Science.gov (United States)

    Ishii-Watabe, Akiko; Hirose, Akihiko; Katori, Noriko; Hashii, Norikata; Arai, Susumu; Awatsu, Hirotoshi; Eiza, Akira; Hara, Yoshiaki; Hattori, Hideshi; Inoue, Tomomi; Isono, Tetsuya; Iwakura, Masahiro; Kajihara, Daisuke; Kasahara, Nobuo; Matsuda, Hiroyuki; Murakami, Sei; Nakagawa, Taishiro; Okumura, Takehiro; Omasa, Takeshi; Takuma, Shinya; Terashima, Iyo; Tsukahara, Masayoshi; Tsutsui, Maiko; Yano, Takahiro; Kawasaki, Nana

    2015-10-01

    Biologics manufacturing technology has made great progress in the last decade. One of the most promising new technologies is the single-use system, which has improved the efficiency of biologics manufacturing processes. To ensure safety of biologics when employing such single-use systems in the manufacturing process, various issues need to be considered including possible extractables/leachables and particles arising from the components used in single-use systems. Japanese pharmaceutical manufacturers, together with single-use suppliers, members of the academia and regulatory authorities have discussed the risks of using single-use systems and established control strategies for the quality assurance of biologics. In this study, we describe approaches for quality risk management when employing single-use systems in the manufacturing of biologics. We consider the potential impact of impurities related to single-use components on drug safety and the potential impact of the single-use system on other critical quality attributes as well as the stable supply of biologics. We also suggest a risk-mitigating strategy combining multiple control methods which includes the selection of appropriate single-use components, their inspections upon receipt and before releasing for use and qualification of single-use systems. Communication between suppliers of single-use systems and the users, as well as change controls in the facilities both of suppliers and users, are also important in risk-mitigating strategies. Implementing these control strategies can mitigate the risks attributed to the use of single-use systems. This study will be useful in promoting the development of biologics as well as in ensuring their safety, quality and stable supply.

  17. [Pharmaceutical product quality control and good manufacturing practices].

    Science.gov (United States)

    Hiyama, Yukio

    2010-01-01

    This report describes the roles of Good Manufacturing Practices (GMP) in pharmaceutical product quality control. There are three keys to pharmaceutical product quality control. They are specifications, thorough product characterization during development, and adherence to GMP as the ICH Q6A guideline on specifications provides the most important principles in its background section. Impacts of the revised Pharmaceutical Affairs Law (rPAL) which became effective in 2005 on product quality control are discussed. Progress of ICH discussion for Pharmaceutical Development (Q8), Quality Risk Management (Q9) and Pharmaceutical Quality System (Q10) are reviewed. In order to reconstruct GMP guidelines and GMP inspection system in the regulatory agencies under the new paradigm by rPAL and the ICH, a series of Health Science studies were conducted. For GMP guidelines, product GMP guideline, technology transfer guideline, laboratory control guideline and change control system guideline were written. For the GMP inspection system, inspection check list, inspection memo and inspection scenario were proposed also by the Health Science study groups. Because pharmaceutical products and their raw materials are manufactured and distributed internationally, collaborations with other national authorities are highly desired. In order to enhance the international collaborations, consistent establishment of GMP inspection quality system throughout Japan will be essential.

  18. Manufacture of aromatic hydrocarbons from coal hydrogenation products

    Energy Technology Data Exchange (ETDEWEB)

    A.S. Maloletnev; M.A. Gyul' malieva [Institute for Fossil Fuels, Moscow (Russian Federation)

    2007-08-15

    The manufacture of aromatic hydrocarbons from coal distillates was experimentally studied. A flow chart for the production of benzene, ethylbenzene, toluene, and xylenes was designed, which comprised the hydrogen treatment of the total wide-cut (or preliminarily dephenolized) fraction with FBP 425{sup o}C; fractional distillation of the hydrotreated products into IBP-60, 60-180, 180-300, and 300-425{sup o}C fractions; the hydro-cracking of middle fractions for increasing the yield of gasoline fractions whenever necessary; the catalytic reform of the fractions with bp up to 180{sup o}C; and the extraction of aromatic hydrocarbons.

  19. Dispersion-strengthened Aluminium Products Manufactured by Powder Blending

    DEFF Research Database (Denmark)

    Hansen, Niels

    1969-01-01

    Detailed experiments carried out to examine relationship between microstructure and mechanical properties of powder-blended aluminum products are reported; their results as well as structural studies by transmission electron microscopy and tensile-and creep- testing, are given; as dispersed phase......, various oxide powders were selected on criterion that during manufacturing no reaction must taken place between metal and oxide phase; strength of powder-blended aluminum products increases and elongation decreases with decreasing particle size of aluminum powder and with increasing concentration of oxide...

  20. Product quality considerations for mammalian cell culture process development and manufacturing.

    Science.gov (United States)

    Gramer, Michael J

    2014-01-01

    The manufacturing of a biologic drug from mammalian cells results in not a single substance, but an array of product isoforms, also known as variants. These isoforms arise due to intracellular or extracellular events as a result of biological or chemical modification. The most common examples related to biomanufacturing include amino acid modifications (glycosylation, isomerization, oxidation, adduct formation, pyroglutamate formation, phosphorylation, sulfation, amidation), amino acid sequence variants (genetic mutations, amino acid misincorporation, N- and C-terminal heterogeneity, clipping), and higher-order structure modifications (misfolding, aggregation, disulfide pairing). Process-related impurities (HCP, DNA, media components, viral particles) are also important quality attributes related to product safety. The observed ranges associated with each quality attribute define the product quality profile. A biologic drug must have a correct and consistent quality profile throughout clinical development and scale-up to commercial production to ensure product safety and efficacy. In general, the upstream process (cell culture) defines the quality of product-related substances, whereas the downstream process (purification) defines the residual level of process- and product-related impurities. The purpose of this chapter is to review the impact of the cell culture process on product quality. Emphasis is placed on studies with industrial significance and where the direct mechanism of product quality impact was determined. Where possible, recommendations for maintaining consistent or improved quality are provided.

  1. Social aspects in additive manufacturing of pharmaceutical products.

    Science.gov (United States)

    Lind, Johanna; Kälvemark Sporrong, Sofia; Kaae, Susanne; Rantanen, Jukka; Genina, Natalja

    2017-08-01

    Additive manufacturing (AM) techniques, such as drug printing, represent a new engineering approach that can implement the concept of personalized medicine via on-demand manufacturing of dosage forms with individually adjusted doses. Implementation of AM principles, such as pharmacoprinting, will challenge the entire drug distribution chain and affect the society at different levels. Areas covered: This work summarizes the concept of personalized medicine and gives an overview of possibilities for monitoring patients' health. The most recent activities in the field of printing technologies for fabrication of dosage forms and 'polypills' with flexible doses and tailored release profiles are reviewed. Different scenarios for the drug distribution chain with the required adjustments in drug logistics, quality systems and environmental safety are discussed, as well as whether AM will be used for production of on-demand medicine. The impact of such changes in the distribution chain on regulation, healthcare professionals and patients are highlighted. Expert opinion: Drug manufacturing by traditional methods is well-established, but it lacks the possibility for on-demand personalized drug production. With the recent approval of the first printed medicine, society should be prepared for the changes that will follow the introduction of printed pharmaceuticals.

  2. Sustainable Product: Personal Protective Equipment Manufactured with Green Plastic

    Directory of Open Access Journals (Sweden)

    Hamilton Aparecido Boa Vista

    2015-04-01

    Full Text Available This study analyzed the case of manufacturing of Personal Protective Equipment (PPE using as raw material biopolymers produced from ethanol from sugar cane, known as green polypropylene, produced since 2008 by BRASKEM. This article studied the PPE for the employee’s head protection, named helmet by NR 6, which is used in situations of exposure to weather and work scenarios in places where there is risk of impact from falling or projecting objects, burns, electric shock, and solar radiation. The MSA, green helmet manufacturer, made an inventory of greenhouse gas emissions into the atmosphere by comparing the two manufacturing processes of the helmet shell, covering the January 1 to December 31, 2011 period. It concluded that the sustainable helmet (green polyethylene and pigments robs 231g of CO2 from the atmosphere per produced unit, while the helmet’s production with traditional raw materials (polyethylene and petrochemical pigments found that, for each unit produced, 1029g of CO2 are emitted into the atmosphere. The study showed that substitution of raw materials has led to reduction in the impact generated in the helmets’ production.

  3. 9 CFR 114.6 - Mixing biological products.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Mixing biological products. 114.6... BIOLOGICAL PRODUCTS § 114.6 Mixing biological products. Each biological product, when in liquid form, shall be mixed thoroughly in a single container. During bottling operations, the product shall be...

  4. Participatory methods for initiating manufacturing employees' involvement in product innovation

    DEFF Research Database (Denmark)

    Jensen, Anna Rose Vagn; Jensen, Christian Schou; Broberg, Ole

    2016-01-01

    approach that we apply to two case companies, this paper presents an empirical study of how to initiate involvement of manufacturing employees in R&D activities. We have used participatory methods from design thinking that has the ability to create relations between employees from different backgrounds......Employee-driven innovation has the potential to improve product innovation by involving employees as innovative resources. However, it can be a challenge to turn the potential into a reality of collaboration practices across organizational structures and culture. Through an interactive research...... and through a series of facilitated workshops we have investigated how these methods can initiate employee involvement. We see that participatory methods can improve understanding and relation between R&D and manufacturing departments, and thereby support a creative collaboration and emergence of employee...

  5. Image slicer manufacturing: from space application to mass production

    Science.gov (United States)

    Bonneville, Christophe; Cagnat, Jean-François; Laurent, Florence; Prieto, Eric; Ancourt, Gérard

    2004-09-01

    This presentation aims to show technical and industrial inputs to be taking into account for Image Slicer systems design and development for different types of projects from space application to mass production for multi-IFU instruments. Cybernétix has a strong experience of precision optics assembled thanks to molecular adhesion and have already manufactured 6 prototypes of image slicer subsystem (prototypes of NIRSPEC-IFU, IFS for JWST, MUSE ...) in collaboration with the Laboratoire d"Astrophysique de Marseille (LAM) and the Centre de Recherche Astronomique de Lyon (CRAL). After a brief presentation of the principle of manufacturing and assembly, we will focus on the different performances achieved in our prototypes of slicer mirrors, pupil and slit mirrors lines: an accuracy on centre of curvature position better than 15 arsec has been obtained for a stack of 30 slices. The contribution of the slice stacking to this error is lower than 4 arcsec. In spite of very thin surfaces (~ 0.9 x 40 mm for instance), a special process allows to guarantee a surface roughness about 5 nm and very few digs on the slice borders. The WFE of the mini-mirror can also be measured at a stage of the manufacturing. Different environmental tests have shown the withstanding of these assemblies to cryogenic temperature (30 K). Then, we will describe the different solutions (spherical, flat, cylindrical surfaces) and characteristics of an image slicer that can influence difficulties of manufacturing and metrology, cost, schedule and risks with regard to fabrication. Finally, the study of a mass production plan for MUSE (CRAL) composed of 24 Image Slicers of 38 slices, that"s to say 912 slices, will be exposed as an example of what can be do for multi-module instruments.

  6. Manufacturing, regulatory and commercial challenges of biopharmaceuticals production: a Finnish perspective.

    Science.gov (United States)

    Närhi, Marko; Nordström, Katrina

    2005-04-01

    Biopharmaceuticals product development is a broad and multidisciplinary field. Science and technology are combined with new manufacturing, regulatory and commercial challenges. However, although there is ample literature on the molecular biology and biochemistry of products, the implementation of processes from test tube to commercial scale has not received similar attention. Consequently, the present study aims to highlight, from practical point of view, some of the key issues involved with manufacturing technologies of biopharmaceuticals at a commercial scale. Regulatory requirements and investments are also addressed based on the practical experiences of start-up and small companies. Finland is used as a case-example of such companies as this is a EU-member state with strong technological growth and rapidly increasing number of biotech companies.

  7. RECONFIGURABLE PRODUCT ROUTING AND CONTROL FOR MASS CUSTOMISATION MANUFACTURING

    Directory of Open Access Journals (Sweden)

    A. J. Walker

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT:Reconfigurable control of flexible manufacturing systems can allow for the efficient and responsive production of customised product instances. This can aid in providing make-to-order business models for various small- to medium-sized enterprises in South Africa, and provide competitive advantage in a dynamic global marketplace. Reconfigurable control application requires an understanding of the modes of production variability in mass customisation manufacturing. Temporally uncorrelated workflow routings are considered as one of these production variability modes. In this light, this paper addresses the flexible material payload routing problem, and presents a mobile robot platform that has been developed to research and design reconfigurable routing systems.

    AFRIKAANSE OPSOMMING:Verstelbare beheer van aanpasbare vervaardigingstelsels kan die doeltreffende en reaktiewe produksie van doelgemaakte produkeksemplare toelaat. Hierdie beheer kan assisteer in die voorsiening van vervaardig-na-bestellingbesigheidsmodelle aan ’n aantal klein- tot medium-grootte ondernemings in Suid-Afrika, en aan hulle ’n kompeterende voorsprong bied in ’n dinamiese globale mark. Die instelling van verstelbare beheer vereis dat die modi van produkveranderlikheid in massa verbruikersaanpassingsvervaardiging verstaan word. Hierdie artikel spreek die probleem van aanpasbare roetebepaling van materiaalvragte in massa verbruikersaanpassingsvervaardiging aan. ’n Mobiele robot-platform, ontwikkel vir navorsing in verstelbare roetebepalingstelsels, word ook voorgelê.

  8. 16 CFR 300.25 - Country where wool products are processed or manufactured.

    Science.gov (United States)

    2010-01-01

    ... an origin label on the unfinished product, the manufacturing processes as required in paragraph (a)(4... processed or manufactured. Further work or material added to the wool product in another country must effect...

  9. Analysis of production flow process with lean manufacturing approach

    Science.gov (United States)

    Siregar, Ikhsan; Arif Nasution, Abdillah; Prasetio, Aji; Fadillah, Kharis

    2017-09-01

    This research was conducted on the company engaged in the production of Fast Moving Consumer Goods (FMCG). The production process in the company are still exists several activities that cause waste. Non value added activity (NVA) in the implementation is still widely found, so the cycle time generated to make the product will be longer. A form of improvement on the production line is by applying lean manufacturing method to identify waste along the value stream to find non value added activities. Non value added activity can be eliminated and reduced by utilizing value stream mapping and identifying it with activity mapping process. According to the results obtained that there are 26% of value-added activities and 74% non value added activity. The results obtained through the current state map of the production process of process lead time value of 678.11 minutes and processing time of 173.94 minutes. While the results obtained from the research proposal is the percentage of value added time of 41% of production process activities while non value added time of the production process of 59%. While the results obtained through the future state map of the production process of process lead time value of 426.69 minutes and processing time of 173.89 minutes.

  10. CUSTOMIZED PRODUCTS: THE INTEGRATING RELATIONSHIP MARKETING, AGILE MANUFACTURING AND SUPPLY CHAIN MANAGEMENT FOR MASS CUSTOMIZATION

    OpenAIRE

    Süleyman BARUTCU

    2007-01-01

    A customized product is a special product designed and manufactured for individual customers to meet their individual needs. Managers need to understand why customers demand and how companies supply customized products. The importance of this study is to highlight business, marketing and manufacturing strategies so as to supply customized products efficiently. It is expected from a manufacturer to successfully adopt relationship marketing, mass customization, agile manufacturing and supply ch...

  11. Intelligent technologies in process of highly-precise products manufacturing

    Science.gov (United States)

    Vakhidova, K. L.; Khakimov, Z. L.; Isaeva, M. R.; Shukhin, V. V.; Labazanov, M. A.; Ignatiev, S. A.

    2017-10-01

    One of the main control methods of the surface layer of bearing parts is the eddy current testing method. Surface layer defects of bearing parts, like burns, cracks and some others, are reflected in the results of the rolling surfaces scan. The previously developed method for detecting defects from the image of the raceway was quite effective, but the processing algorithm is complicated and lasts for about 12 ... 16 s. The real non-stationary signals from an eddy current transducer (ECT) consist of short-time high-frequency and long-time low-frequency components, therefore a transformation is used for their analysis, which provides different windows for different frequencies. The wavelet transform meets these conditions. Based on aforesaid, a methodology for automatically detecting and recognizing local defects in bearing parts surface layer has been developed on the basis of wavelet analysis using integral estimates. Some of the defects are recognized by the amplitude component, otherwise an automatic transition to recognition by the phase component of information signals (IS) is carried out. The use of intelligent technologies in the manufacture of bearing parts will, firstly, significantly improve the quality of bearings, and secondly, significantly improve production efficiency by reducing (eliminating) rejections in the manufacture of products, increasing the period of normal operation of the technological equipment (inter-adjustment period), the implementation of the system of Flexible facilities maintenance, as well as reducing production costs.

  12. 40 CFR Figure E-2 to Subpart E of... - Product Manufacturing Checklist

    Science.gov (United States)

    2010-07-01

    ... Testing Physical (Design) and Performance Characteristics of Reference Methods and Class I and Class II... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Product Manufacturing Checklist E...—Product Manufacturing Checklist PRODUCT MANUFACTURING CHECKLIST AuditeeAuditor signatureDate Compliance...

  13. 27 CFR 40.1 - Manufacture of tobacco products, cigarette papers and tubes, and processed tobacco.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Manufacture of tobacco... MANUFACTURE OF TOBACCO PRODUCTS, CIGARETTE PAPERS AND TUBES, AND PROCESSED TOBACCO Scope of Regulations § 40.1 Manufacture of tobacco products, cigarette papers and tubes, and processed tobacco. This part contains...

  14. Manufacturing history of etanercept (Enbrel®): Consistency of product quality through major process revisions.

    Science.gov (United States)

    Hassett, Brian; Singh, Ena; Mahgoub, Ehab; O'Brien, Julie; Vicik, Steven M; Fitzpatrick, Brian

    2018-01-01

    Etanercept (ETN) (Enbrel®) is a soluble protein that binds to, and specifically inhibits, tumor necrosis factor (TNF), a proinflammatory cytokine. ETN is synthesized in Chinese hamster ovary cells by recombinant DNA technology as a fusion protein, with a fully human TNFRII ectodomain linked to the Fc portion of human IgG1. Successful manufacture of biologics, such as ETN, requires sophisticated process and product understanding, as well as meticulous control of operations to maintain product consistency. The objective of this evaluation was to show that the product profile of ETN drug substance (DS) has been consistent over the course of production. Multiple orthogonal biochemical analyses, which included evaluation of attributes indicative of product purity, potency, and quality, were assessed on >2,000 batches of ETN from three sites of DS manufacture, during the period 1998-2015. Based on the key quality attributes of product purity (assessed by hydrophobic interaction chromatography HPLC), binding activity (to TNF by ELISA), potency (inhibition of TNF-induced apoptosis by cell-based bioassay) and quality (N-linked oligosaccharide map), we show that the integrity of ETN DS has remained consistent over time. This consistency was maintained through three major enhancements to the initial process of manufacturing that were supported by detailed comparability assessments, and approved by the European Medicines Agency. Examination of results for all major quality attributes for ETN DS indicates a highly consistent process for over 18 years and throughout changes to the manufacturing process, without affecting safety and efficacy, as demonstrated across a wide range of clinical trials of ETN in multiple inflammatory diseases.

  15. The Scientific Context of Product Portfolio Management at Manufacturing Firms

    Directory of Open Access Journals (Sweden)

    Alvaro Luiz Neuenfeldt Júnior

    2014-12-01

    Full Text Available Correct product portfolio management is one of the feasible ways of ensuring competitive sustainability before continued market evolution whereby decisions to maintain or exclude an item from the sales offering drives consequences that impact both internal and external contexts. In alignment with this standpoint, the purpose of this study is to identify and pinpoint the conceptual framework on product portfolio management, particularly in as much as existing applications centred on manufacturing sector firms is concerned, so as to allow for the envisioning of possible opportunities of fostering future investigations on the subject matter. To this effect, theoretical-conceptual research was conducted, starting with the primary definition of how this field of study is explored right through to the bibliometric review of existing publications. The end result was the identification a gap in research that focuses on portfolio management at manufacturing companies, particularly in Brazil where only two studies centred on this theme were found, although the country hosts more than 30 types of organizations of this kind.

  16. Report of working committee 2 production of manufactured gases; Rapport du comite de travail 2 production de gaz manufactures

    Energy Technology Data Exchange (ETDEWEB)

    Lau, F.S.

    2000-07-01

    The Committee's work during this triennium focused on 4 topic areas. They are: the potential of hydrogen in meeting long term energy demands, future development prospects for manufactured gas units/gasification of coal, biomass, and opportunity materials for the production of electricity and chemicals, recovery of methane from coal seams, and update on management of contaminated gas sites. This report presents the status and the potentials of present and future opportunities for the gas industry in the areas of manufactured gases including hydrogen and coal bed/mine methane. The idea of hydrogen as an energy carrier is getting increased attention these days for its promise of super clean emissions at the point of use. The development of fuel cells for stationary and mobile applications has highlighted the need of hydrogen production, storage and infrastructure. Hydrogen appears destined to be a major energy source of the future. The industry for gasification is growing, particularly for the production of electricity and chemicals from opportunity fuels, such as petroleum coke from refineries. Coal and biomass are also getting increased interests due to their promise of high efficiency and lower emissions. Methane from coal mines is also getting increased attention due not only to its environmental benefits but also to its favorable own economics. The future of the energy industry will be price and environmentally driven. A well-informed gas industry will be in a position to continue to play a major role in the future of the energy industry world-wide. (author)

  17. Six sigma and lean production adoption in a manufacturing company

    Directory of Open Access Journals (Sweden)

    Alisson Christian Scheller

    2014-11-01

    Full Text Available The connection among Lean Production with Six Sigma originated the Lean Six Sigma methodology, focused on processes variation and waste reduction. This methodology was developed on different ways in the companies and there is no consensus over its structure and its implementation. In this context, this paper aims to identify and analyze the main characteristics on the adoption and integration of Lean Six Sigma methodology through a case study conducted in a manufacturing company that adopts lean production and six sigma. The results show two important aspects of the Lean Six Sigma methodology. One of them is the adoption of the value stream mapping as a central tool on Lean Six Sigma. The other is the use of DMAIC for improvements actions. The study indicates that despite the difficulties on Lean Six Sigma implementation, the methodology offers benefits to the company that adopts it in the suitable way.

  18. Inventory Management Strategies For Productivity Improvement In Equipment Manufacturing Firms

    Directory of Open Access Journals (Sweden)

    T.T Amachree

    2017-08-01

    Full Text Available This study examined and developed Inventory Management Strategies IMS which could be creatively employed for Productivity Improvement in Equipment Firms PIEMF Equipment manufacturing projects suffer from declining productivity and inability to effectively satisfy customized order batch quantity within schedules budgeted cost and quality specifications due to lack of robust and well defined IMS as well as none code classification of vast number of inventory item. Survey and expost-facto research designs were adopted on the four identified IMS in three EMF. The method used for primary data collection and measurement on four IMS and inventory management parameters was questionnaire modelled into likert five point scale from the target respondents being experts in the subject matter. The secondary data was obtained from the computerised inventory status file of the three equipment manufacturing firms. The methods of primary data analysis and test of research used were Pearsons product moment correlation coefficient and oneway. Analysis of variance ANOVA computer software via Statistical Program for Social Science SPSS version 17 ABC analysis and classification of materials was used for code categorization of secondary data also with the aid of Microsoft excel. The results of the analyses highlighted and isolated A class of inventory items which are 137 out of 543 for Siemens Nig. Ltd 154 out of 551 for Dresser-Rand Nig. Ltd and 162 of 551 for Nigerian Engineering Works Ltd. The results of Pearson product moment correlation analysis and test of research hypotheses indicate that Materials Requirements Planning MRP followed by Supply Chain Management SCM are the most significant IMS as they correlate strongly with PIEMF. The study recommends IMS adoption by code classification of materials in which MRP or SCM could be deployed for management of A class of inventories while classical IMS could be used for management B and C classes of inventory items.

  19. Dendritic cells for active immunotherapy: optimizing design and manufacture in order to develop commercially and clinically viable products.

    Science.gov (United States)

    Nicolette, C A; Healey, D; Tcherepanova, I; Whelton, P; Monesmith, T; Coombs, L; Finke, L H; Whiteside, T; Miesowicz, F

    2007-09-27

    Dendritic cell (DC) active immunotherapy is potentially efficacious in a broad array of malignant disease settings. However, challenges remain in optimizing DC-based therapy for maximum clinical efficacy within manufacturing processes that permit quality control and scale-up of consistent products. In this review we discuss the critical issues that must be addressed in order to optimize DC-based product design and manufacture, and highlight the DC based platforms currently addressing these issues. Variables in DC-based product design include the type of antigenic payload used, DC maturation steps and activation processes, and functional assays. Issues to consider in development include: (a) minimizing the invasiveness of patient biological material collection; (b) minimizing handling and manipulations of tissue at the clinical site; (c) centralized product manufacturing and standardized processing and capacity for commercial-scale production; (d) rapid product release turnaround time; (e) the ability to manufacture sufficient product from limited starting material; and (f) standardized release criteria for DC phenotype and function. Improvements in the design and manufacture of DC products have resulted in a handful of promising leads currently in clinical development.

  20. Biological fluidized-bed treatment of groundwater from a manufactured gas plant site

    International Nuclear Information System (INIS)

    Grey, G.M.; Scheible, O.K.; Maiello, J.A.; Guarini, W.J.; Sutton, P.M.

    1995-01-01

    Bench- and pilot-scale biological treatability studies were performed as part of a comprehensive study for developing an on-site treatment system for contaminated groundwater at a former manufactured gas plant site. The bench-scale work, which included evaluations of activated sludge and fluidized-bed biological processes, indicated that a carbon-based fluidized-bed process was most appropriate. The process was then demonstrated on a pilot level at the site. The bench and pilot studies demonstrated significant reductions of chemical oxygen demand (COD), and all target organics including polycyclic aromatic hydrocarbons (PAHs) and volatile organic compounds (VOCs)

  1. Evolution of approaches to viral safety issues for biological products.

    Science.gov (United States)

    Lubiniecki, Anthony S

    2011-01-01

    CONFERENCE PROCEEDING Proceedings of the PDA/FDA Adventitious Viruses in Biologics: Detection and Mitigation Strategies Workshop in Bethesda, MD, USA; December 1-3, 2010 Guest Editors: Arifa Khan (Bethesda, MD), Patricia Hughes (Bethesda, MD) and Michael Wiebe (San Francisco, CA) Approaches to viral safety issues for biological products have evolved during the past 50+ years. The first cell culture products (viral vaccines) relied largely on the use of in vitro and in vivo virus screening assays that were based upon infectivity of adventitious viral agents. The use of Cohn fractionation and pasteurization by manufacturers of plasma derivatives introduced the concepts that purification and treatment with physical and chemical agents could greatly reduce the risk of viral contamination of human albumin and immunoglobulin products. But the limitations of such approaches became clear for thermolabile products that were removed early in fractionation such as antihemophilic factors, which transmitted hepatitis viruses and HIV-1 to some product recipients. These successes and limitations were taken into account by the early developers of recombinant DNA (rDNA)-derived cell culture products and by regulatory agencies, leading to the utilization of cloning technology to reduce/eliminate contamination due to human viruses and purification technologies to physically remove and inactivate adventitious and endogenous viruses, along with cell banking and cell bank characterization for adventitious and endogenous viruses, viral screening of biological raw materials, and testing of cell culture harvests, to ensure virus safety. Later development and incorporation of nanofiltration technology in the manufacturing process provided additional assurance of viral clearance for safety of biotechnology products. These measures have proven very effective at preventing iatrogenic infection of recipients of biotechnology products; however, viral contamination of production cell cultures has

  2. Design and research on the platform of network manufacture product electronic trading

    Science.gov (United States)

    Zhou, Zude; Liu, Quan; Jiang, Xuemei

    2003-09-01

    With the rapid globalization of market and business, E-trading affects every manufacture enterprise. However, the security of network manufacturing products of transmission on Internet is very important. In this paper we discussed the protocol of fair exchange and platform for network manufacture products E-trading based on fair exchange protocol and digital watermarking techniques. The platform realized reliable and copyright protection.

  3. Systems biology solutions for biochemical production challenges

    DEFF Research Database (Denmark)

    Hansen, Anne Sofie Lærke; Lennen, Rebecca M; Sonnenschein, Nikolaus

    2017-01-01

    There is an urgent need to significantly accelerate the development of microbial cell factories to produce fuels and chemicals from renewable feedstocks in order to facilitate the transition to a biobased society. Methods commonly used within the field of systems biology including omics...... characterization, genome-scale metabolic modeling, and adaptive laboratory evolution can be readily deployed in metabolic engineering projects. However, high performance strains usually carry tens of genetic modifications and need to operate in challenging environmental conditions. This additional complexity...... compared to basic science research requires pushing systems biology strategies to their limits and often spurs innovative developments that benefit fields outside metabolic engineering. Here we survey recent advanced applications of systems biology methods in engineering microbial production strains...

  4. Systems biology solutions for biochemical production challenges.

    Science.gov (United States)

    Hansen, Anne Sofie Lærke; Lennen, Rebecca M; Sonnenschein, Nikolaus; Herrgård, Markus J

    2017-06-01

    There is an urgent need to significantly accelerate the development of microbial cell factories to produce fuels and chemicals from renewable feedstocks in order to facilitate the transition to a biobased society. Methods commonly used within the field of systems biology including omics characterization, genome-scale metabolic modeling, and adaptive laboratory evolution can be readily deployed in metabolic engineering projects. However, high performance strains usually carry tens of genetic modifications and need to operate in challenging environmental conditions. This additional complexity compared to basic science research requires pushing systems biology strategies to their limits and often spurs innovative developments that benefit fields outside metabolic engineering. Here we survey recent advanced applications of systems biology methods in engineering microbial production strains for biofuels and -chemicals. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  5. Hydrogen production from biomass by biological systems

    International Nuclear Information System (INIS)

    Sharifan, H.R.; Qader, S.

    2009-01-01

    Hydrogen gas is seen as a future energy carrier, not involved in 'greenhouse' gas and its released energy in combustion can be converted to electric power. Biological system with low energy can produce hydrogen compared to electrochemical hydrogen production via solar battery-based water splitting which requires the use of solar batteries with high energy requirements. The biological hydrogen production occurs in microalgae and cyanobacteria by photosynthesis. They consume biochemical energy to produce molecular hydrogen. Hydrogen in some algae is an anaerobic production in the absence of light. In cyanobacteria the hydrogen production simultaneously happens with nitrogen fixation, and also catalyzed by nitrogenase as a side reaction. Hydrogen production by photosynthetic bacteria is mediated by nitrogenase activity, although hydrogenases may be active for both hydrogen production and hydrogen uptake under some conditions. Genetic studies on photosynthetic microorganisms have markedly increased in recent times, relatively few genetic engineering studies have focused on altering the characteristics of these microorganisms, particularly with respect to enhancing the hydrogen-producing capabilities of photosynthetic bacteria and cyanobacteria. (author)

  6. Novel fermentation processes for manufacturing plant natural products.

    Science.gov (United States)

    Zhou, Jingwen; Du, Guocheng; Chen, Jian

    2014-02-01

    Microbial production of plant natural products (PNPs), such as terpenoids, flavonoids from renewable carbohydrate feedstocks offers sustainable and economically attractive alternatives to their petroleum-based production. Rapid development of metabolic engineering and synthetic biology of microorganisms shows many advantages to replace the current extraction of these useful high price chemicals from plants. Although few of them were actually applied on a large scale for PNPs production, continuous research on these high-price chemicals and the rapid growing global market of them, show the promising future for the production of these PNPs by microorganisms with a more economic and environmental friendly way. Introduction of novel pathways and optimization of the native cellular processes by metabolic engineering of microorganisms for PNPs production are rapidly expanding its range of cell-factory applications. Here we review recent progress in metabolic engineering of microorganisms for the production of PNPs. Besides, factors restricting the yield improvement and application of lab-scale achievements to industrial applications have also been discussed. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. System for manufacturing ash products and energy from refuse waste

    Energy Technology Data Exchange (ETDEWEB)

    Sutin, G.L.; Mahoney, P.F.

    1996-01-04

    The present invention provides a system of manufacturing energy and ash products from solid waste. The system includes apparatus for receiving solid waste for processing, apparatus for shredding the received solid waste, apparatus for removing ferrous material from the shredded solid waste to create processed refuse fuel (PRF) and apparatus for efficiently combusting the PRF. A conveyor transfers the PRF to the combusting apparatus such that the density of the PRF is always controlled for continuous non-problematic flow. Apparatus for recovering residual combustion particulate from the combustion residual gases and for recovering solid ash residue provides the system with the ability to generate steam and electrical energy, and to recover for reuse and recycling valuable materials from the solid ash residue. (author) figs.

  8. 9 CFR 112.6 - Packaging biological products.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Packaging biological products. 112.6... AGRICULTURE VIRUSES, SERUMS, TOXINS, AND ANALOGOUS PRODUCTS; ORGANISMS AND VECTORS PACKAGING AND LABELING § 112.6 Packaging biological products. (a) Each multiple-dose final container of a biological product...

  9. Microbial production of hydrogen from starch-manufacturing wastes

    Energy Technology Data Exchange (ETDEWEB)

    Yokoi, H.; Maki, R.; Hirose, J.; Hayashi, S. [Miyazaki Univ. (Japan). Dept. of Applied Chemistry

    2002-05-01

    Effective hydrogen production from starch-manufacturing wastes by microorganisms was investigated. Continuous hydrogen production in high yield of 2.7 mol H{sub 2} mol{sup -1} glucose was attained by a mixed culture of Clostridium butyricum and Enterobacter aerogenes HO-39 in the starch waste medium consisting of sweet potato starch residue as a carbon source and corn steep liquor as a nitrogen source in a repeated batch culture. Rhodobacter sp. M-19 could produce hydrogen from the supernatant of the culture broth obtained in the repeated batch culture of C. butyricum and E. aerogenes HO-39. Hydrogen yield of 4.5 mol H{sub 2} mol{sup -1} glucose was obtained by culturing Rhodobacter sp. M-19 in the supernatant supplemented with 20{mu}gl{sup -1} Na{sub 2}MoO{sub 4} 2H{sub 2}O and 10mgl{sup -1} EDTA in a repeated batch culture with pH control at 7.5. Therefore, continuous hydrogen production with total hydrogen yield of 7.2 mol H{sub 2} mol{sup -1} glucose from the starch remaining in the starch residue was attained by the repeated batch culture with C. butyricum and E. aerogenes HO-39 and by the successive repeated batch culture with Rhodobacter sp. M-19. (Author)

  10. 16 CFR 1211.24 - Product certification and labeling by manufacturers.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Product certification and labeling by manufacturers. 1211.24 Section 1211.24 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT... § 1211.24 Product certification and labeling by manufacturers. (a) Form of permanent label of...

  11. Application of magnetic resonance imaging and spectroscopy in studying the biological effects of manufactured nanoparticles

    International Nuclear Information System (INIS)

    Lei Hao; Wei Li; Liu Maili

    2006-01-01

    With the rapid development of nanoscience and nanotechnology in recent years, growing research interest and efforts have been directed to study the biological effects of manufactured nanoparticles and substances alike. Despite the fact that significant progress has been made, this is still largely an uncharted field. Any advances in this field would certainly require thorough multi-disciplinary collaboration, in which the expertise and tools in nanoscience/nanotechnoloogy, physics, chemistry and biomedicine have to be combined. Due to their wide range of applications in physics, chemistry and biomedicine, magnetic resonance (MR) imaging and spectroscopy are among the most important and powerful research tools currently in use, mainly because these techniques can be used in situ and noninvasively to acquire dynamic and real-time information in various samples ranging from protein solution to the human brain. In this paper, the application of MR imaging and spectroscopy in studying the biological effects of manufactured nanoparticles is discussed. It is expected that these techniques will play important roles in 1) detecting the presence of nanoparticles in biological tissues and in vivo, 2) studying the interactions between the nanoparticles and biomolecules and 3) investigating the metabonomic aspect of the biological effects of nanoparticles. (authors)

  12. Computational manufacturing as a bridge between design and production.

    Science.gov (United States)

    Tikhonravov, Alexander V; Trubetskov, Michael K

    2005-11-10

    Computational manufacturing of optical coatings is a research area that can be placed between theoretical designing and practical manufacturing in the same way that computational physics can be placed between theoretical and experimental physics. Investigations in this area have been performed for more than 30 years under the name of computer simulation of manufacturing and monitoring processes. Our goal is to attract attention to the increasing importance of computational manufacturing at the current state of the art in the design and manufacture of optical coatings and to demonstrate possible applications of this research tool.

  13. Productivity improvement in the production line with lean manufacturing approach: case study PT. XYZ

    Directory of Open Access Journals (Sweden)

    diah Halimatussa’

    2018-01-01

    Full Text Available The increaseing productivity is one of the competitive strategies that can be applied in a company in order to survive in an intense competitive presure. PT. XYZ is a textile industry manufacturing golf gloves and caddy bag. Every day, the company has a production target of 600 pieces per line. However, the desired target is not achieved that it will affect the delay in delivery of products to customers. In this research, a case study on implementing value stream mapping and Kaizen as the lean manufacturing concept is reported. The purpose of this study is to map the current production line, analyse and design the future value stream mapping by eliminating waste occured. It is obtained a lead time reduction as much as 440.4 seconds through eliminating 17 non-value added activities. Then, the output can be increased up to 21% which is equal to 502 pieces.

  14. Glocalized Production - A Holistic Approach for Future Manufacturing at The LEGO Group

    DEFF Research Database (Denmark)

    Hadar, Ronen

    2014-01-01

    ) and Rapid Manufacturing (RM). RMS is a manufacturing system that is designed for rapid changes. It is based on core characteristics such as modularity, convertibility, customized flexibility, etc.. RM is the use of Additive Manufacturing (AM –commonly referred to as 3D printing) for the production......Global production is changing. Changes in production paradigms, global competition, manufacturing technologies, and new mega trends such as individualization, inflict immense challenges on global manufacturers. A new holistic approach for facing supply chain and production challenges is proposed...... facilities, the establishment of production close to main markets, and the creation of a global network of independent factories and supply chains with local manufacturing. Doing so will potentially increase responsiveness, cut transportation costs, reduce complexity, enable production to demand rather than...

  15. Good Manufacturing Practices (GMP) manufacturing of advanced therapy medicinal products: a novel tailored model for optimizing performance and estimating costs.

    Science.gov (United States)

    Abou-El-Enein, Mohamed; Römhild, Andy; Kaiser, Daniel; Beier, Carola; Bauer, Gerhard; Volk, Hans-Dieter; Reinke, Petra

    2013-03-01

    Advanced therapy medicinal products (ATMP) have gained considerable attention in academia due to their therapeutic potential. Good Manufacturing Practice (GMP) principles ensure the quality and sterility of manufacturing these products. We developed a model for estimating the manufacturing costs of cell therapy products and optimizing the performance of academic GMP-facilities. The "Clean-Room Technology Assessment Technique" (CTAT) was tested prospectively in the GMP facility of BCRT, Berlin, Germany, then retrospectively in the GMP facility of the University of California-Davis, California, USA. CTAT is a two-level model: level one identifies operational (core) processes and measures their fixed costs; level two identifies production (supporting) processes and measures their variable costs. The model comprises several tools to measure and optimize performance of these processes. Manufacturing costs were itemized using adjusted micro-costing system. CTAT identified GMP activities with strong correlation to the manufacturing process of cell-based products. Building best practice standards allowed for performance improvement and elimination of human errors. The model also demonstrated the unidirectional dependencies that may exist among the core GMP activities. When compared to traditional business models, the CTAT assessment resulted in a more accurate allocation of annual expenses. The estimated expenses were used to set a fee structure for both GMP facilities. A mathematical equation was also developed to provide the final product cost. CTAT can be a useful tool in estimating accurate costs for the ATMPs manufactured in an optimized GMP process. These estimates are useful when analyzing the cost-effectiveness of these novel interventions. Copyright © 2013 International Society for Cellular Therapy. Published by Elsevier Inc. All rights reserved.

  16. Foundations & principles of distributed manufacturing elements of manufacturing networks, cyber-physical production systems and smart automation

    CERN Document Server

    Kühnle, Hermann

    2015-01-01

    The book presents a coherent description of distributed manufacturing, providing a solid base for further research on the subject as well as smart implementations in companies. It provides a guide for those researching and working in a range of fields, such as smart manufacturing, cloud computing, RFID tracking, distributed automation, cyber physical production and global design anywhere, manufacture anywhere solutions. Foundations & Principles of Distributed Manufacturing anticipates future advances in the fields of embedded systems, the Internet of Things and cyber physical systems, outlining how adopting these innovations could rapidly bring about improvements in key performance indicators, which could in turn generate competition pressure by rendering successful business models obsolete. In laying the groundwork for powerful theoretical models, high standards for the homogeneity and soundness of the suggested setups are applied. The book especially elaborates on the upcoming competition in online manu...

  17. 78 FR 4307 - Current Good Manufacturing Practice Requirements for Combination Products

    Science.gov (United States)

    2013-01-22

    ...-2009-N-0435] Current Good Manufacturing Practice Requirements for Combination Products AGENCY: Food and...) is issuing this regulation on the current good manufacturing practice (CGMP) requirements applicable... this subpart? (Sec. 4.2) D. What current good manufacturing practice requirements apply to my...

  18. Chemical Biology of Microbial Anticancer Natural Products

    DEFF Research Database (Denmark)

    Bladt, Tanja Thorskov; Gotfredsen, Charlotte Held

    than 100 years. New natural products (NPs) are continually discovered and with the increase in selective biological assays, previously described compounds often also display novel bioactivities, justifying their presence in novel screening efforts. Screening and discovery of compounds with activity...... towards chronic lymphocytic leukemia (CLL) cells is crucial since CLL is considered as an incurable disease. To discover novel agents that targets CLL cells is complicated. CLL cells rapidly undergo apoptosis in vitro when they are removed from their natural microenvironment, even though they are long...

  19. Urine: Waste product or biologically active tissue?

    Science.gov (United States)

    2018-03-01

    Historically, urine has been viewed primarily as a waste product with little biological role in the overall health of an individual. Increasingly, data suggest that urine plays a role in human health beyond waste excretion. For example, urine might act as an irritant and contribute to symptoms through interaction with-and potential compromise of-the urothelium. To explore the concept that urine may be a vehicle for agents with potential or occult bioactivity and to discuss existing evidence and novel research questions that may yield insight into such a role, the National Institute of Diabetes and Digestive and Kidney Disease invited experts in the fields of comparative evolutionary physiology, basic science, nephrology, urology, pediatrics, metabolomics, and proteomics (among others) to a Urinology Think Tank meeting on February 9, 2015. This report reflects ideas that evolved from this meeting and current literature, including the concept of urine quality, the biological, chemical, and physical characteristics of urine, including the microbiota, cells, exosomes, pH, metabolites, proteins, and specific gravity (among others). Additionally, the manuscript presents speculative, and hopefully testable, ideas about the functional roles of urine constituents in health and disease. Moving forward, there are several questions that need further understanding and pursuit. There were suggestions to consider actively using various animal models and their biological specimens to elaborate on basic mechanistic information regarding human bladder dysfunction. Published 2018. This article is a U.S. Government work and is in the public domain in the USA.

  20. Manufacturing cycle for pure neon-helium mixture production

    International Nuclear Information System (INIS)

    Batrakov, B.P.; Kravchenko, V.A.

    1980-01-01

    The manufacturing cycle for pure neon-helium mixture production with JA-300 nitrogen air distributing device has been developed. Gas mixture containing 2-3% of neon-helium mixture (the rest is mainly nitrogen 96-97%) is selected out of the cover of the JA-300 column condensator and enters the deflegmator under the 2.3-2.5 atm. pressure. The diflegmator presents a heat exchange apparatus in which at 78 K liquid nitrogen the condensation of nitrogen from the mixture of gases entering from the JA-300 column takes place. The enriched gas mixture containing 65-70% of neon-helium mixture and 30-35% of nitrogen goes out from the deflegmator. This enriched neon-helium mixture enters the gasgoeder for impure (65-70%) neon-helium mixture. Full cleaning of-neon helium mixture of nitrogen is performed by means of an adsorber. As adsorbent an activated coal has been used. Adsorption occurs at the 78 K temperature of liquid nitrogen and pressure P=0.1 atm. As activated coal cooled down to nitrogen temperature adsorbs nitrogen better than neon and helium, the nitrogen from the mixture is completely adsorbed. Pure neon-helium mixture from the adsorber comes into a separate gasgolder. In one campaign the cycle allows obtaining 2 m 3 of the mixture. The mixture contains 0.14% of nitrogen, 0.01% of oxygen and 0.06% of hydrogen

  1. Biological treatment of wastewaters from a dye manufacturing company using a trickling filter

    International Nuclear Information System (INIS)

    Kornaros, M.; Lyberatos, G.

    2006-01-01

    The aim of this work was to assess the effectiveness of a biological trickling filter for the treatment of wastewaters produced by a company manufacturing organic dyes and varnishes. The combined wastewater effluent was fed to a pilot-scale trickling filter in two feeding modes, continuously and as a sequencing batch reactor (SBR). The biodegradability of the diluted wastewaters that were subjected to physicochemical treatment, using Ca(OH) 2 and FeSO 4 , was initially studied using a continuously operated trickling filter. The system efficiency ranged up to 60-70% for a hydraulic loading of 1.1 m 3 /m 2 day and up to 80-85% for a hydraulic loading 0.6 m 3 /m 2 day. A stable chemical oxygen demand (COD) removal efficiency of 60-70% was achieved even in the case of undiluted wastewater at a hydraulic loading of 1.1 m 3 /m 2 day. The effectiveness of biological treatment of a mixture of the company's main wastewater streams was also examined. The microorganisms developed in the trickling filter were able to efficiently remove COD levels up to 36,000 mg/L, under aerobic conditions at pH values between 5.5 and 8.0. Depending on the operating conditions of the system, about 30-60% of the total COD removal was attributed to air stripping caused by the air supply at the bottom of the filter, whereas the rest of the COD was clearly removed through biological action. The proposed biological treatment process based on a trickling filter, which was operated either continuously or even better in an SBR mode, appears as a promising pretreatment step for coping with dye manufacturing wastewaters in terms of removing a significant portion of the organic content

  2. A Systematic Approach to Quality Oriented Product Sequencing for Multistage Manufacturing Systems

    OpenAIRE

    Zhang, Faping; Butt, Shahid Ikramullah

    2016-01-01

    Product sequencing is one way to reduce cost and improve product quality for multistage manufacturing systems (MMS). However, systematically evaluating the influence of product sequence on quality performance for MMS is still a challenge. By considering the rate of incoming conforming product, manufacturing system quality transition between batch to batch, and quality propagation along stages, this paper investigates the appropriate batch policies and product sequencing for MMS so that satisf...

  3. Design of production process main shaft process with lean manufacturing to improve productivity

    Science.gov (United States)

    Siregar, I.; Nasution, A. A.; Andayani, U.; Anizar; Syahputri, K.

    2018-02-01

    This object research is one of manufacturing companies that produce oil palm machinery parts. In the production process there is delay in the completion of the Main shaft order. Delays in the completion of the order indicate the low productivity of the company in terms of resource utilization. This study aimed to obtain a draft improvement of production processes that can improve productivity by identifying and eliminating activities that do not add value (non-value added activity). One approach that can be used to reduce and eliminate non-value added activity is Lean Manufacturing. This study focuses on the identification of non-value added activity with value stream mapping analysis tools, while the elimination of non-value added activity is done with tools 5 whys and implementation of pull demand system. Based on the research known that non-value added activity on the production process of the main shaft is 9,509.51 minutes of total lead time 10,804.59 minutes. This shows the level of efficiency (Process Cycle Efficiency) in the production process of the main shaft is still very low by 11.89%. Estimation results of improvement showed a decrease in total lead time became 4,355.08 minutes and greater process cycle efficiency that is equal to 29.73%, which indicates that the process was nearing the concept of lean production.

  4. Investigating factors that influence level and dynamics of capital productivity in plants manufacturing equipment for mines

    Energy Technology Data Exchange (ETDEWEB)

    Karenov, R.S. (Karagandinskii Politekhnicheskii Institut (USSR))

    1990-10-01

    Analyzes productivity of capital in plants manufacturing equipment for underground coal mining in the USSR. Effects of the following factors are evaluated: working time, investment, mechanization of manufacturing processes, power of motors used to drive the manufacturing equipment, duration of a manufacturing cycle, cooperation degree, equipment service life. Effects of insufficient specialization of manufacturing plants and the manufacturing of mining equipment by repair shops of individual mines which should rather specialize in equipment repair and maintenance are evaluated. Analysis shows that specialization of the manufacturing plants could increase productivity of capital by 1.5-2.0 times, reduce labor consumption by 3-5 times and consumption of materials by 1.5-1.7 times. 4 refs.

  5. A pharmacology guided approach for setting limits on product-related impurities for bispecific antibody manufacturing.

    Science.gov (United States)

    Rajan, Sharmila; Sonoda, Junichiro; Tully, Timothy; Williams, Ambrose J; Yang, Feng; Macchi, Frank; Hudson, Terry; Chen, Mark Z; Liu, Shannon; Valle, Nicole; Cowan, Kyra; Gelzleichter, Thomas

    2018-04-13

    bFKB1 is a humanized bispecific IgG1 antibody, created by conjoining an anti-Fibroblast Growth Factor Receptor 1 (FGFR1) half-antibody to an anti-Klothoβ (KLB) half-antibody, using the knobs-into-holes strategy. bFKB1 acts as a highly selective agonist for the FGFR1/KLB receptor complex and is intended to ameliorate obesity-associated metabolic defects by mimicking the activity of the hormone FGF21. An important aspect of the biologics product manufacturing process is to establish meaningful product specifications regarding the tolerable levels of impurities that copurify with the drug product. The aim of the current study was to determine acceptable levels of product-related impurities for bFKB1. To determine the tolerable levels of these impurities, we dosed obese mice with bFKB1 enriched with various levels of either HMW impurities or anti-FGFR1-related impurities, and measured biomarkers for KLB-independent FGFR1 signaling. Here, we show that product-related impurities of bFKB1, in particular, high molecular weight (HMW) impurities and anti-FGFR1-related impurities, when purposefully enriched, stimulate FGFR1 in a KLB-independent manner. By taking this approach, the tolerable levels of product-related impurities were successfully determined. Our study demonstrates a general pharmacology-guided approach to setting a product specification for a bispecific antibody whose homomultimer-related impurities could lead to undesired biological effects. Copyright © 2018. Published by Elsevier Inc.

  6. Manufacturing of Zirconium products at Chepetsky Mechanical Plant, Stock Company. Prospects of development and products quality assurance

    International Nuclear Information System (INIS)

    Vergazov, K.; Shtuza, M.; Lozitsky, S.; Kutyavin, A.

    2015-01-01

    The report described all the steps required to fabricate zirconium components, starting from the procurement of feed material up to rolling of sheets, tubes, bars and manufacture of the applicable parts required to manufacture fuel assemblies. Automated state-of-the-art equipment used for advanced productivity, as well as various installations able to perform numerous inspection steps to assure quality of the manufactured products was showcased. The challenges to be addressed in the nearest future were also presented

  7. Systems biology of microbial exopolysaccharides production

    Directory of Open Access Journals (Sweden)

    Ozlem eAtes

    2015-12-01

    Full Text Available Exopolysaccharides (EPS produced by diverse group of microbial systems are rapidly emerging as new and industrially important biomaterials. Due to their unique and complex chemical structures and many interesting physicochemical and rheological properties with novel functionality, the microbial EPSs find wide range of commercial applications in various fields of the economy such as food, feed, packaging, chemical, textile, cosmetics and pharmaceutical industry, agriculture and medicine. EPSs are mainly associated with high-value applications and they have received considerable research attention over recent decades with their biocompatibility, biodegradability, and both environmental and human compatibility. However only a few microbial EPSs have achieved to be used commercially due to their high production costs. The emerging need to overcome economic hurdles and the increasing significance of microbial EPSs in industrial and medical biotechnology call for the elucidation of the interrelations between metabolic pathways and EPS biosynthesis mechanism in order to control and hence enhance its microbial productivity. Moreover a better understanding of biosynthesis mechanism is a significant issue for improvement of product quality and properties and also for the design of novel strains. Therefore a systems-based approach constitutes an important step towards understanding the interplay between metabolism and EPS biosynthesis and further enhances its metabolic performance for industrial application. In this review, primarily the microbial EPSs, their biosynthesis mechanism and important factors for their production will be discussed. After this brief introduction, recent literature on the application of omics technologies and systems biology tools for the improvement of production yields will be critically evaluated. Special focus will be given to EPSs with high market value such as xanthan, levan, pullulan and dextran.

  8. Systems Biology of Microbial Exopolysaccharides Production.

    Science.gov (United States)

    Ates, Ozlem

    2015-01-01

    Exopolysaccharides (EPSs) produced by diverse group of microbial systems are rapidly emerging as new and industrially important biomaterials. Due to their unique and complex chemical structures and many interesting physicochemical and rheological properties with novel functionality, the microbial EPSs find wide range of commercial applications in various fields of the economy such as food, feed, packaging, chemical, textile, cosmetics and pharmaceutical industry, agriculture, and medicine. EPSs are mainly associated with high-value applications, and they have received considerable research attention over recent decades with their biocompatibility, biodegradability, and both environmental and human compatibility. However, only a few microbial EPSs have achieved to be used commercially due to their high production costs. The emerging need to overcome economic hurdles and the increasing significance of microbial EPSs in industrial and medical biotechnology call for the elucidation of the interrelations between metabolic pathways and EPS biosynthesis mechanism in order to control and hence enhance its microbial productivity. Moreover, a better understanding of biosynthesis mechanism is a significant issue for improvement of product quality and properties and also for the design of novel strains. Therefore, a systems-based approach constitutes an important step toward understanding the interplay between metabolism and EPS biosynthesis and further enhances its metabolic performance for industrial application. In this review, primarily the microbial EPSs, their biosynthesis mechanism, and important factors for their production will be discussed. After this brief introduction, recent literature on the application of omics technologies and systems biology tools for the improvement of production yields will be critically evaluated. Special focus will be given to EPSs with high market value such as xanthan, levan, pullulan, and dextran.

  9. 49 CFR 661.6 - Certification requirements for procurement of steel or manufactured products.

    Science.gov (United States)

    2010-10-01

    ... § 661.6 Certification requirements for procurement of steel or manufactured products. If steel, iron, or... 49 Transportation 7 2010-10-01 2010-10-01 false Certification requirements for procurement of steel or manufactured products. 661.6 Section 661.6 Transportation Other Regulations Relating to...

  10. Management Accounting in the Manufacturing Sector: Managing Costs at the Design and Production Stages

    NARCIS (Netherlands)

    Davila, Tony; Wouters, Marc; Chapman, Christopher S.; Hopwood, Anthony G.; Shields, Michael D.

    2006-01-01

    This chapter analyzes the empirical research literature on management accounting in the manufacturing sector including the development as well and manufacturing phases of the product lifecycle. As managing product development has gained terrain in companies over the last 15 years, management

  11. Advanced Process Chains for Prototyping and Pilot Production based on Additive Manufacturing

    DEFF Research Database (Denmark)

    Mischkot, Michael

    2015-01-01

    For many years, Additive Manufacturing (AM) has been a well-established production technology used mainly for rapid prototyping. But the need for increased flexibility and economic low volume production led to the discovery of Additive Manufacturing as a suitable fabrication technique (Mellor 2013...

  12. Quality Improvement, Inventory Management, Lead Time Reduction and Production Scheduling in High-Mix Manufacturing Environments

    Science.gov (United States)

    2017-01-13

    Quality Improvement , Inventory Management, Lead Time Reduction and Production Scheduling in High-mix Manufacturing Environments by Sean Daigle B.S...Mechanical Engineering Chairman, Department Committee on Graduate Theses 2 Quality Improvement , Inventory Management, Lead Time Reduction and... Production Scheduling in High-mix Manufacturing Environments by Sean Daigle Submitted to the Department of Mechanical Engineering on January 13, 2017, in

  13. 41 CFR 101-26.702 - Purchase of products manufactured by the Federal Prison Industries, Inc.

    Science.gov (United States)

    2010-07-01

    ... manufactured by the Federal Prison Industries, Inc. 101-26.702 Section 101-26.702 Public Contracts and Property... Defense § 101-26.702 Purchase of products manufactured by the Federal Prison Industries, Inc. (a) Purchases by executive agencies of prison-made products carried in GSA supply distribution facilities must...

  14. 16 CFR 303.33 - Country where textile fiber products are processed or manufactured.

    Science.gov (United States)

    2010-01-01

    ... [Foreign Country]”. (ii) When the U.S. Customs Service requires an origin label on the unfinished product... manufactured. Further work or material added to the textile fiber product in another country must effect a...

  15. Recombinant biologic products versus nutraceuticals from plants - a regulatory choice?

    Science.gov (United States)

    Drake, Pascal M W; Szeto, Tim H; Paul, Mathew J; Teh, Audrey Y-H; Ma, Julian K-C

    2017-01-01

    Biotechnology has transformed the potential for plants to be a manufacturing source of pharmaceutical compounds. Now, with transgenic and transient expression techniques, virtually any biologic, including vaccines and therapeutics, could be manufactured in plants. However, uncertainty over the regulatory path for such new pharmaceuticals has been a deterrent. Consideration has been given to using alternative regulatory paths, including those for nutraceuticals or cosmetic agents. This review will consider these possibilities, and discuss the difficulties in establishing regulatory guidelines for new pharmaceutical manufacturing technologies. © 2016 The British Pharmacological Society.

  16. Good manufacturing practice (GMP) compliance in the biologics sector: plasma fractionation.

    Science.gov (United States)

    Ways, J P; Preston, M S; Baker, D; Huxsoll, J; Bablak, J

    1999-12-01

    The U.S. blood supply is the safest it has ever been. Due to blood safety and the introduction of viral inactivation/clearance technologies, protein therapies derived from human blood have also in recent years had a history of product safety. Nevertheless, since 1995, the plasma-fractionation industry has experienced increased compliance-related actions by the Food and Drug Administration (FDA), as shown by a substantive increase in the number of FDA 483 inspectional observations, FDA warning letters and other FDA regulatory action. An evaluation of these trends shows that they reflect the implementation by the FDA of increased inspectional interest in the plasma-fractionation industry and an evolution of inspectional practices and standards of current good manufacturing practice (cGMP). Plasma fractionators have responded to FDA actions by carefully evaluating and addressing each inspectional observation, assessing impact to product and taking appropriate actions, including corrective actions to prevent future occurrence. They have made major investments in facilities, quality systems, personnel and training to meet the evolving standards of cGMP and in an effort to implement these standards systemically. Through industry associations, manufacturers have further enhanced product safety by adopting additional voluntary standards for plasma to prevent the entry of potentially unsuitable plasma into the production process. The industry remains committed to application of cGMP and to working with the FDA in further evolution of these standards while striving to assure a continued supply of safe, pure and effective plasma-derived therapies.

  17. Consistent manufacturing and quality control of a highly complex recombinant polyclonal antibody product for human therapeutic use.

    Science.gov (United States)

    Frandsen, Torben P; Naested, Henrik; Rasmussen, Søren K; Hauptig, Peter; Wiberg, Finn C; Rasmussen, Lone Kjaer; Jensen, Anne Marie Valentin; Persson, Pia; Wikén, Margareta; Engström, Anders; Jiang, Yun; Thorpe, Susan J; Förberg, Cecilia; Tolstrup, Anne B

    2011-09-01

    The beneficial effect of antibody therapy in human disease has become well established mainly for the treatment of cancer and immunological disorders. The inherent monospecificity of mAbs present limitations to mAb therapy which have become apparent notably in addressing complex entities like infectious agents or heterogenic endogenous targets. For such indications mixtures of antibodies comprising a combination of specificities would convey more potent biological effect which could translate into therapeutic efficacy. Recombinant polyclonal antibodies (rpAb) consisting of a defined number of well-characterized mAbs constitute a new class of target specific antibody therapy. We have developed a cost-efficient cell banking and single-batch manufacturing concept for the production of such products and demonstrate that a complex pAb composition, rozrolimupab, comprising 25 individual antibodies can be manufactured in a highly consistent manner in a scaled-up manufacturing process. We present a strategy for the release and characterization of antibody mixtures which constitute a complete series of chemistry, manufacturing, and control (CMC) analytical methods to address identity, purity, quantity, potency, and general characteristics. Finally we document selected quality attributes of rozrolimupab based on a battery of assays at the genetic-, protein-, and functional level and demonstrate that the manufactured rozrolimupab batches are highly pure and very uniform in their composition. Copyright © 2011 Wiley Periodicals, Inc.

  18. Research and Development Strategy in Biological Technologies: A Patent Data Analysis of Japanese Manufacturing Firms

    Directory of Open Access Journals (Sweden)

    Hidemichi Fujii

    2016-04-01

    Full Text Available Biological technology allows us to invent new medical approaches, create effective food production methods and reserves and develop new materials for industrial production. There is a diversity of biological technology types, and different technologies have different priorities for invention. This study examines the factors that are important for the invention of biology-related technologies in Japan using patent application data and a decomposition analysis framework. As the results show, patent applications related to biochemistry and biotechnology increased until 1995 because of the expanded scale of R&D activities and the high priority assigned to biological technology. However, the number of patent applications stagnated after 1995, because the importance of biochemistry, especially waste-gas treatment technologies, decreased. Additionally, patent applications for medicines and disease-related technologies increased rapidly from 1971 to 1995. The primary determinant of rapid growth is an increase in research priority, especially among firms in the chemical industry whose technologies are related to supplemental foods and foods with health-promoting benefits. Finally, patent applications involving foodstuff- and agriculture-related technologies increased from 1971 to 1995 due to increased R&D and the increased priority of biological technology.

  19. Automotive Manufacturing Assessment System : Volume 1. Master Product Schedules.

    Science.gov (United States)

    1999-11-01

    Volume I is part of a four volume set documenting areas of research resulting from the development of the Automotive Manufacturing Assessment System (AMAS) for the DOT/Transportation Systems Center. AMAS was designed to assist in the evaluation of in...

  20. Human Capital Linkages to Labour Productivity: Implications from Thai Manufacturers

    Science.gov (United States)

    Rukumnuaykit, Pungpond; Pholphirul, Piriya

    2016-01-01

    Human capital investment is a necessary condition for improving labour market outcomes in most countries. Empirical studies to investigate human capital and its linkages on the labour demand side are, however, relatively scarce due to limitations of firm-level data-sets. Using firm-level data from the Thai manufacturing sector, this paper aims to…

  1. Domestic Wood Products Manufacturing Trends and Factors to Enhance Competitiveness

    Science.gov (United States)

    Urs Buehlmann; Matthew Bumgardner; Albert Schuler; Rich Christianson; Rich Christianson

    2003-01-01

    There is little question that imports have captured a substantial portion of the domestic furniture market. However, there is much speculation and concern as to the future of this and related industries. This study sought to obtain industry perspectives of trends in domestic manufacturing and importing, and to identify factors that can enhance domestic competitiveness...

  2. Methodology for designing and manufacturing complex biologically inspired soft robotic fluidic actuators: prosthetic hand case study.

    Science.gov (United States)

    Thompson-Bean, E; Das, R; McDaid, A

    2016-10-31

    We present a novel methodology for the design and manufacture of complex biologically inspired soft robotic fluidic actuators. The methodology is applied to the design and manufacture of a prosthetic for the hand. Real human hands are scanned to produce a 3D model of a finger, and pneumatic networks are implemented within it to produce a biomimetic bending motion. The finger is then partitioned into material sections, and a genetic algorithm based optimization, using finite element analysis, is employed to discover the optimal material for each section. This is based on two biomimetic performance criteria. Two sets of optimizations using two material sets are performed. Promising optimized material arrangements are fabricated using two techniques to validate the optimization routine, and the fabricated and simulated results are compared. We find that the optimization is successful in producing biomimetic soft robotic fingers and that fabrication of the fingers is possible. Limitations and paths for development are discussed. This methodology can be applied for other fluidic soft robotic devices.

  3. Eradication of Productivity Related Problems Through Lean Principles In Integrated Manufacturing Environment

    Directory of Open Access Journals (Sweden)

    Rahul

    2013-06-01

    Full Text Available In this competitive era, manufacturing enterprises struggle to adopt cost-effective manufacturing systems. Overview of the recent manufacturing enterprises shows that successful global manufacturing enterprises have distributed their manufacturing capabilities over the globe. The successes of distributed integrated manufacturing enterprises depend upon the adaptation of appropriate manufacturing technologies like computer integrated manufacturing (CIM under the global collaborative environment along with the principles of lean manufacturing so that their corporate goals are achieved. CIM is an umbrella term which involves automated design, analysis, planning manufacturing, dispatching, customer-interaction, purchasing, cost accounting, inventory control and factory floor functions, which are inter-linked through the computer, to control all the campus-wide manufacturing related operations. It helps to improve the performance of a firm by integrating various areas of manufacturing business in which most of lean ideas are embedded. These lean ideas cause work in a process to be performed with minimum of non-value adding activities and focus on customers’ needs by delivering them at minimum time, with high quality and at minimum cost by eliminating hidden waste. What happens at the shop floor of even an integrated industry is that proper and timely attention is not paid to the intangible lean principles in the manual part of the CIM system which results in substantial loss of the plant productivity. Therefore the objective of this research paper is to investigate the different poor productivity-related problems in a partially integrated manufacturing environment and lay down the remedial measures to eradicate them using ‘Juran’s problem solving techniques’ and various ‘lean tools’ which results in the reduced wastages and hence improved productivity.

  4. Life Cycle Assessment of Fiber-Reinforced Additive Manufacturing for Injection Molding Insert Production

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Stotz, Philippe Maurice; Bey, Niki

    2017-01-01

    Additively manufactured (AM) injection molding (IM) inserts have proved to be capable to substitute conventionally manufactured metal inserts with polymer-based insert enforced with short, virgin, unseized carbon fibers (CFs). It has been shown that the implementation of AM technology resulted......, this contribution provides a comparison of environmental performance of conventionally vs. additively manufactured inserts in a full life cycle perspective indicated in Figure 1, including materials, production, use and end-of-life (EoL) stages....

  5. Product carbon footprint assessment supporting the green supply chain construction in household appliance manufacturers

    Science.gov (United States)

    Chen, Jianhua; Sun, Liang; Guo, Huiting

    2017-11-01

    Supply chain carbon emission is one of the factors considered in the green supply chain management. A method was designed to support the green supply chain measures based on the carbon footprint assessment for products. A research for 3 typical household appliances carbon footprint assessment was conducted to explore using product carbon footprint assessment method to guide the green supply chain management of the manufacturers. The result could reflect the differences directions on green supply chain management of manufacturers of washing machine, air conditioner and microwave, respectively That is, the washing machine manufacturer should pay attention to the low carbon activities in upstream suppliers in highest priority, and also the promotion of product energy efficiency. The air conditioner manufacturer should pay attention to the product energy efficiency increasing in highest priority, and the improvement of refrigerant to decrease its GWP. And the microwave manufacture could only focus on the energy efficiency increasing because it contributes most of the carbon emission to its carbon footprint. Besides, the representativeness of product and the applicability of the method were also discussed. As the manufacturer could master the technical information on raw material and components of its products to conduct the product carbon footprint assessment, this method could help the manufacturer to identify the effective green supply chain measures in the preliminary stage.

  6. Emerging technology: A key enabler for modernizing pharmaceutical manufacturing and advancing product quality.

    Science.gov (United States)

    O'Connor, Thomas F; Yu, Lawrence X; Lee, Sau L

    2016-07-25

    Issues in product quality have produced recalls and caused drug shortages in United States (U.S.) in the past few years. These quality issues were often due to outdated manufacturing technologies and equipment as well as lack of an effective quality management system. To ensure consistent supply of safe, effective and high-quality drug products available to the patients, the U.S. Food and Drug Administration (FDA) supports modernizing pharmaceutical manufacturing for improvements in product quality. Specifically, five new initiatives are proposed here to achieve this goal. They include: (i) advancing regulatory science for pharmaceutical manufacturing; (ii) establishing a public-private institute for pharmaceutical manufacturing innovation; (iii) creating incentives for investment in the technological upgrade of manufacturing processes and facilities; (iv) leveraging external expertise for regulatory quality assessment of emerging technologies; and (v) promoting the international harmonization of approaches for expediting the global adoption of emerging technologies. Published by Elsevier B.V.

  7. 3D Machine Vision and Additive Manufacturing: Concurrent Product and Process Development

    International Nuclear Information System (INIS)

    Ilyas, Ismet P

    2013-01-01

    The manufacturing environment rapidly changes in turbulence fashion. Digital manufacturing (DM) plays a significant role and one of the key strategies in setting up vision and strategic planning toward the knowledge based manufacturing. An approach of combining 3D machine vision (3D-MV) and an Additive Manufacturing (AM) may finally be finding its niche in manufacturing. This paper briefly overviews the integration of the 3D machine vision and AM in concurrent product and process development, the challenges and opportunities, the implementation of the 3D-MV and AM at POLMAN Bandung in accelerating product design and process development, and discusses a direct deployment of this approach on a real case from our industrial partners that have placed this as one of the very important and strategic approach in research as well as product/prototype development. The strategic aspects and needs of this combination approach in research, design and development are main concerns of the presentation.

  8. 16 CFR 1205.35 - Product certification and labeling by manufacturers.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Product certification and labeling by manufacturers. 1205.35 Section 1205.35 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT SAFETY ACT REGULATIONS SAFETY STANDARD FOR WALK-BEHIND POWER LAWN MOWERS Certification § 1205.35 Product...

  9. 27 CFR 17.5 - Products manufactured in Puerto Rico or the Virgin Islands.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Products manufactured in Puerto Rico or the Virgin Islands. 17.5 Section 17.5 Alcohol, Tobacco Products and Firearms ALCOHOL AND... in medicines, medicinal preparations, food products, flavors, flavoring extracts, or perfume which...

  10. Qualification of laser based additive production for manufacturing of forging Tools

    Directory of Open Access Journals (Sweden)

    Junker Daniel

    2015-01-01

    Full Text Available Mass customization leads to very short product life cycles, so the costs of a tool have to be amortized with a low number of workpieces. Especially for highly loaded tools, like those for forging, that leads to expensive products. Therefore more economical production processes for tool manufacturing have to be investigated. As laser additive manufacturing is already used for the production of moulds for injection moulding, this technology maybe could also improve the forging tool production. Within this paper laser metal deposition, which is industrially used for tool repair, will be investigated for the use in tool manufacturing. Therefore a mechanical characterization of parts built with different laser process parameters out of the hot work tool steel 1.2709 is made by upsetting tests and hardness measurements. So the influence of the additive manufacturing process on the hardness distribution is analysed.

  11. Does private-label production by national-brand manufacturers create discounter goodwill?

    NARCIS (Netherlands)

    Ter Braak, A.M.; Deleersnyder, B.; Geyskens, I.; Dekimpe, M.G.

    2013-01-01

    Discount stores have a private-label dominated assortment where national brands have only limited shelf access. These limited spots are in high demand by national-brand manufacturers. We examine whether private-label production by leading national-brand manufacturers for two important discounters

  12. The added value of Good Manufacturing Practices (GMP) in the production of radiopharmaceuticals

    NARCIS (Netherlands)

    Gerrits, Edwin; Woerdenbag, Herman; Luurtsema, Geert; de Hooge, Marjolijn; Boersma, Hendrikus

    2017-01-01

    Manufacturers of medicinal products including radiopharmaceuticals have to follow regulations from their governmental organizations as well as professional societies to ensure built-in quality combined with patient safety issues. This chapter is a concise review of Good Manufacturing Practices (GMP)

  13. 78 FR 16824 - Tobacco Product Manufacturing Practice; Establishment of a Public Docket

    Science.gov (United States)

    2013-03-19

    ... manufacturing operations. DATES: Submit electronic or written comments on the tobacco companies' recommendations... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration 21 CFR Chapter I [Docket No. FDA-2013-N-0227] Tobacco Product Manufacturing Practice; Establishment of a Public Docket AGENCY: Food...

  14. Biological evaluation of recombinant human erythropoietin in pharmaceutical products

    Directory of Open Access Journals (Sweden)

    Ramos A.S.

    2003-01-01

    Full Text Available The potencies of mammalian cell-derived recombinant human erythropoietin pharmaceutical preparations, from a total of five manufacturers, were assessed by in vivo bioassay using standardized protocols. Eight-week-old normocythemic mice received a single subcutaneous injection followed by blood sampling 96 h later or multiple daily injections with blood sampling 24 h after the last injection. Reticulocyte counting by microscopic examination was employed as the end-point using the brilliant cresyl blue or selective hemolysis methods, together with automated flow cytometry. Different injection schedules were investigated and dose-response curves for the European Pharmacopoeia Biological Reference Preparation of erythropoietin were compared. Manual and automated methods of reticulocyte counting were correlated with respect to assay validity and precision. Using 8 mice per treatment group, intra-assay precision determined for all of the assays in the study showed coefficients of variation of 12.1-28.4% for the brilliant cresyl blue method, 14.1-30.8% for the selective hemolysis method and 8.5-19.7% for the flow cytometry method. Applying the single injection protocol, a combination of at least two independent assays was required to achieve the precision potency and confidence limits indicated by the manufacturers, while the multiple daily injection protocol yielded the same acceptable results within a single assay. Although the latter protocol using flow cytometry for reticulocyte counting gave more precise and reproducible results (intra-assay coefficients of variation: 5.9-14.2%, the well-characterized manual methods provide equally valid alternatives for the quality control of recombinant human erythropoietin therapeutic products.

  15. Biosynthesis of therapeutic natural products using synthetic biology.

    Science.gov (United States)

    Awan, Ali R; Shaw, William M; Ellis, Tom

    2016-10-01

    Natural products are a group of bioactive structurally diverse chemicals produced by microorganisms and plants. These molecules and their derivatives have contributed to over a third of the therapeutic drugs produced in the last century. However, over the last few decades traditional drug discovery pipelines from natural products have become far less productive and far more expensive. One recent development with promise to combat this trend is the application of synthetic biology to therapeutic natural product biosynthesis. Synthetic biology is a young discipline with roots in systems biology, genetic engineering, and metabolic engineering. In this review, we discuss the use of synthetic biology to engineer improved yields of existing therapeutic natural products. We further describe the use of synthetic biology to combine and express natural product biosynthetic genes in unprecedented ways, and how this holds promise for opening up completely new avenues for drug discovery and production. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. Practical Aspects of CALS in Design and Manufacturing of Sheet Metal Products

    DEFF Research Database (Denmark)

    Shpitalni, Moshe; Alting, Leo; Bilberg, Arne

    1998-01-01

    The transition from design to process planning and to the various stages of manufacturing is traditionally sequential. In many cases, practical problems associated with manufacturing cannot be resolved if only individual processes are examined. These problems can be overcome, however, by adopting...... with the design and manufacture of sheet metal parts. It is demonstrated that through implementation of the CALS approach, the overall process can be optimised and products can be manufactured significantly more accurately, faster and less expensively.......The transition from design to process planning and to the various stages of manufacturing is traditionally sequential. In many cases, practical problems associated with manufacturing cannot be resolved if only individual processes are examined. These problems can be overcome, however, by adopting...

  17. Biological control and sustainable food production

    NARCIS (Netherlands)

    Bale, J.S.; Lenteren, van J.C.; Bigler, F.

    2008-01-01

    The use of biological control for the management of pest insects pre-dates the modern pesticide era. The first major successes in biological control occurred with exotic pests controlled by natural enemy species collected from the country or area of origin of the pest (classical control).

  18. Global Production Planning Process considering the Supply Risk of Overseas Manufacturing Sites

    Directory of Open Access Journals (Sweden)

    Hosang Jung

    2015-01-01

    Full Text Available Although global manufacturers can produce most of their final products in local plants, they need to source components or parts from desirable overseas manufacturing partners at low cost in order to fulfill customer orders. In this global manufacturing environment, capacity information for planning is usually imprecise owing to the various risks of overseas plants (e.g., foreign governments’ policies and labor stability. It is therefore not easy for decision-makers to generate a global production plan showing the production amounts at local plants and overseas manufacturing facilities operated by manufacturing partners. In this paper, we present a new global production planning process considering the supply risk of overseas manufacturing sites. First, local experts estimate the supply capacity of an overseas plant using their judgment to determine when the risk could occur and how large the risk impact would be. Next, we run a global production planning model with the estimated supply capacities. The proposed process systematically adopts the qualitative judgments of local experts in the global production planning process and thus can provide companies with a realistic global production plan. We demonstrate the applicability of the proposed process with a real world case.

  19. 9 CFR 101.3 - Biological products and related terms.

    Science.gov (United States)

    2010-01-01

    ... as required by the regulations. (e) Released product. A finished product released for marketing after... total quantity of completed product which has been thoroughly mixed in a single container and identified... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Biological products and related terms...

  20. Cellulose Products Manufacturing: National Emission Standards for Hazardous Air Pollutants (NESHAP)

    Science.gov (United States)

    Read the National Emission Standards for Hazardous Air Pollutants (NESHAP) for Cellulose Products Manufacturing, see the rule history for this Maximum Achievable Control Technology (MACT), and find Compliance help for this source.

  1. Quality Productivity Circle in Manufacture | Achi | Nigerian Journal of ...

    African Journals Online (AJOL)

    A brief history of quality control and productivity is hereby traced. ... Circle management technique are discussed in its relationship with productivity. ... so should be made sound in body (and spirit) through appropriate training and motivation.

  2. Validation of a sterilization dose for products manufactured using a 3D printer

    Science.gov (United States)

    Wangsgard, Wendy; Winters, Martell

    2018-02-01

    As more healthcare products are personalized, the use of unique, patient-specific products will increase. Some of these are manufactured using a 3D printing process (also known as additive manufacturing) for either polymers or metals. For these products, processes such as sterilization validations must be handled in a different manner. The concepts typically used are still relevant but are approached from an alternative perspective to account for a potential production batch size of one, and for the great variability that can occur in size and shape of a product.

  3. Lean manufacturing analysis to reduce waste on production process of fan products

    Science.gov (United States)

    Siregar, I.; Nasution, A. A.; Andayani, U.; Sari, R. M.; Syahputri, K.; Anizar

    2018-02-01

    This research is based on case study that being on electrical company. One of the products that will be researched is the fan, which when running the production process there is a time that is not value-added, among others, the removal of material which is not efficient in the raw materials and component molding fan. This study aims to reduce waste or non-value added activities and shorten the total lead time by using the tools Value Stream Mapping. Lean manufacturing methods used to analyze and reduce the non-value added activities, namely the value stream mapping analysis tools, process mapping activity with 5W1H, and tools 5 whys. Based on the research note that no value-added activities in the production process of a fan of 647.94 minutes of total lead time of 725.68 minutes. Process cycle efficiency in the production process indicates that the fan is still very low at 11%. While estimates of the repair showed a decrease in total lead time became 340.9 minutes and the process cycle efficiency is greater by 24%, which indicates that the production process has been better.

  4. 16 CFR 1203.34 - Product certification and labeling by manufacturers (including importers).

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Product certification and labeling by... COMMISSION CONSUMER PRODUCT SAFETY ACT REGULATIONS SAFETY STANDARD FOR BICYCLE HELMETS Certification § 1203.34 Product certification and labeling by manufacturers (including importers). (a) Form of permanent...

  5. 78 FR 58273 - Approval for Manufacturing (Production) Authority, Foreign-Trade Zone 284, Liberty Pumps, Inc...

    Science.gov (United States)

    2013-09-23

    ... (Production) Authority, Foreign-Trade Zone 284, Liberty Pumps, Inc. (Submersible and Water Pumps), Bergen, New... (production) authority on behalf of Liberty Pumps, Inc., within FTZ 284 in Bergen, New York (FTZ Docket 5-2012... manufacturing (production) authority under zone procedures within FTZ 284 on behalf of Liberty Pumps, Inc., as...

  6. Quantifying the robustness of process manufacturing concept – A medical product case study

    DEFF Research Database (Denmark)

    Boorla, Srinivasa Murthy; Troldtoft, M.E.; Eifler, Tobias

    2017-01-01

    Product robustness refers to the consistency of performance of all of the units produced. It is often the case that process manufactured products are not designed concurrently, so by the end of the product design phase the Process Manufacturing Concept (PMC) has yet to be decided. Allocating...... the unit-to-unit robustness of an early-stage for a PMC is proposed. The method uses variability and adjustability information from the manufacturing concept in combination with sensitivity information from products' design to predict its functional performance variation. A Technology maturation factor...... process capable tolerances to the product during the design phase is therefore not possible. The robustness of the concept (how capable it is to achieve the product specification), only becomes clear at this late stage and thus after testing and iteration. In this article, a method for calculating...

  7. Development of Integrated Programs for Aerospace-vehicle Design (IPAD): Product manufacture interactions with the design process

    Science.gov (United States)

    Crowell, H. A.

    1979-01-01

    The product manufacturing interactions with the design process and the IPAD requirements to support the interactions are described. The data requirements supplied to manufacturing by design are identified and quantified. Trends in computer-aided manufacturing are discussed and the manufacturing process of the 1980's is anticipated.

  8. Identified research directions for using manufacturing knowledge earlier in the product lifecycle.

    Science.gov (United States)

    Hedberg, Thomas D; Hartman, Nathan W; Rosche, Phil; Fischer, Kevin

    2017-01-01

    Design for Manufacturing (DFM), especially the use of manufacturing knowledge to support design decisions, has received attention in the academic domain. However, industry practice has not been studied enough to provide solutions that are mature for industry. The current state of the art for DFM is often rule-based functionality within Computer-Aided Design (CAD) systems that enforce specific design requirements. That rule-based functionality may or may not dynamically affect geometry definition. And, if rule-based functionality exists in the CAD system, it is typically a customization on a case-by-case basis. Manufacturing knowledge is a phrase with vast meanings, which may include knowledge on the effects of material properties decisions, machine and process capabilities, or understanding the unintended consequences of design decisions on manufacturing. One of the DFM questions to answer is how can manufacturing knowledge, depending on its definition, be used earlier in the product lifecycle to enable a more collaborative development environment? This paper will discuss the results of a workshop on manufacturing knowledge that highlights several research questions needing more study. This paper proposes recommendations for investigating the relationship of manufacturing knowledge with shape, behavior, and context characteristics of product to produce a better understanding of what knowledge is most important. In addition, the proposal includes recommendations for investigating the system-level barriers to reusing manufacturing knowledge and how model-based manufacturing may ease the burden of knowledge sharing. Lastly, the proposal addresses the direction of future research for holistic solutions of using manufacturing knowledge earlier in the product lifecycle.

  9. The Use of Alternative Raw Material in Production of Pastry Products as a Progressive Direction in Creating the Products of High Biological Value

    Directory of Open Access Journals (Sweden)

    Janа Bachinska

    2017-02-01

    Full Text Available This paper examines the impact of the use of alternative vegetable raw materials in the manufacture of pastry products with high biological value; it presents the results of evaluation of commodity of the developed products and compares them with the main samples presented in Kharkiv trade network. The feasibility of using a mixture of fiber and pumpkin seeds in the technology of pastry production to extend the range of confectionery products of high biological value and products with reduced calories has been proved. Adding the mixture of fiber and pumpkin seeds to biscuits and cakes positively affected the chemical composition of the ready-made product, saturating it with useful and necessary to human body mineral elements, vitamins, dietary fiber.

  10. MANUFACTURING PRICES, PRODUCTIVITY, AND LABOR COSTS IN 5 ECONOMIES

    NARCIS (Netherlands)

    VANARK, B

    The United States continues to surge ahead of other major industrial economies in terms of lower prices, higher levels of labor productivity, and better unit labor cost performance; while the depreciation of the dollar plays an important role, real productivity gains are important as well.

  11. Manufacturing processes in the textile industry. Expert Systems for fabrics production

    OpenAIRE

    Bullon, Juan; González Arrieta, Angélica; Hernández Encinas, Ascensión; Queiruga Dios, Araceli

    2017-01-01

    The textile industry is characterized by the economic activity whose objective is the production of fibres, yarns, fabrics, clothing and textile goods for home and decoration,as well as technical and industrial purposes. Within manufacturing, the Textile is one of the oldest and most complex sectors which includes a large number of sub-sectors covering the entire production cycle, from raw materials and intermediate products, to the production of final products. Textile industry activities pr...

  12. 75 FR 33312 - Indexing Structured Product Labeling for Human Prescription Drug and Biological Products; Request...

    Science.gov (United States)

    2010-06-11

    ...] Indexing Structured Product Labeling for Human Prescription Drug and Biological Products; Request for... Biologics Evaluation and Research (CBER) are indexing certain categories of information in product labeling for use as terms to search repositories of approved prescription medical product structured product...

  13. 9 CFR 114.17 - Rebottling of biological products.

    Science.gov (United States)

    2010-01-01

    ... reports of all tests conducted on the rebottled product shall be submitted to Animal and Plant Health... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Rebottling of biological products. 114.17 Section 114.17 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT...

  14. Relationship Between Lean Production and Operational Performance in the Manufacturing Industry

    Science.gov (United States)

    Rasi, Raja Zuraidah R. M.; Syamsyul Rakiman, Umol; Ahmad, Md Fauzi Bin

    2015-05-01

    Nowadays, more and more manufacturing firms have started to implement lean production system in their operations. Lean production viewed as one of the mechanism to maintain the organisation's position and to compete globally. However, many fail to apply the lean concepts successfully in their operations. Based on previous studies, implementation of lean production in the manufacturing industry is more focused on the relationship between Lean and Operational Performance of one dimension only. Therefore, this study attempted to examine the relationship between Lean Production (LP) and Operational Performance in 4 dimensions which are quality, delivery, cost and flexibility. This study employed quantitative study using questionnaires. Data was collected from 50 manufacturing industries. The data was analysed using Statistical Package for Social Science (SPSS) 22.0. This study is hoped to shed new understanding on the concept of Lean Production (LP) in regards of Operational Performance covering the 4 dimensions.

  15. EVALUATION OF MANUFACTURING AND AGRICULTURAL PRODUCTION BY THE END OF THE FINANCIAL PERIOD

    Directory of Open Access Journals (Sweden)

    Mincho Minev

    2016-06-01

    Full Text Available This article is dedicated on the matter of evaluation of manufacturing and agricultural production after the initial appraisal. Accounting standards and regulations, concerning the reappraisal of production, are discussed with emphasis on the key and most disputable requirements. The most commonly met difficulties in the process of reappraisal of production are pointed out. A research is done over the leading manufacturing and agricultural entities in Bulgaria. The point of the research is to study the degree on witch entities met the requirements and regulations of accounting standards when they reevaluate their production by the end of the year. The results of the research are shown and analyzed. Conclusions are made along with some recommendations in order to improve the quality of reappraisal of manufacturing and agricultural production.

  16. MICROORGANISMS IN SELECTED CONFECTIONARY PRODUCTS DURING THE MANUFACTURING PROCESS

    Directory of Open Access Journals (Sweden)

    Jana Petrová

    2015-02-01

    Full Text Available The aim of our study was to evaluate the microbiological quality confectionery products during production. A total of 135 samples were analyzed: 45 samples of the punch balls, 45 Venček samples and 45 samples French cubes from home, school and private production. For microorganism cultivation VRBL agar for the isolation of coliform bacteria, DRBC and DG18 for microscopic fungi and yeasts, Plate Count Agar for total viable count, Meat peptone agar for mesophilic aerobic bacteria, XLD agar for Salmonella sp. and Baird Parker agar for Staphylococcus aureus were used. Following microbiological parameters were tested: total viable count, mesophilic anaerobic microorganisms, coliform bacteria, yeast and microscopic filamentous fungi, Salmonella spp. and Staphylococcus aureus. Products are assessed according to the limit values of the number of microorganisms contained in the Codex Alimentary of the Slovak Republic. The overall assessment of the microbiological quality of the punch balls, we found that two samples from school factory and one sample from private producer did not meet CA SR for the total viable count. Comparing the microbiological quality of Venček with CA SR, we found that one sample of home production did not meet the requirements for this type of product. All the tested samples were Staphylococcus aureus and Salmonella spp. negative. Comparing the results of the samples with French cubes CA SR, we found that all the samples satisfy requirements.

  17. In-use product stocks link manufactured capital to natural capital.

    Science.gov (United States)

    Chen, Wei-Qiang; Graedel, T E

    2015-05-19

    In-use stock of a product is the amount of the product in active use. In-use product stocks provide various functions or services on which we rely in our daily work and lives, and the concept of in-use product stock for industrial ecologists is similar to the concept of net manufactured capital stock for economists. This study estimates historical physical in-use stocks of 91 products and 9 product groups and uses monetary data on net capital stocks of 56 products to either approximate or compare with in-use stocks of the corresponding products in the United States. Findings include the following: (i) The development of new products and the buildup of their in-use stocks result in the increase in variety of in-use product stocks and of manufactured capital; (ii) substitution among products providing similar or identical functions reflects the improvement in quality of in-use product stocks and of manufactured capital; and (iii) the historical evolution of stocks of the 156 products or product groups in absolute, per capita, or per-household terms shows that stocks of most products have reached or are approaching an upper limit. Because the buildup, renewal, renovation, maintenance, and operation of in-use product stocks drive the anthropogenic cycles of materials that are used to produce products and that originate from natural capital, the determination of in-use product stocks together with modeling of anthropogenic material cycles provides an analytic perspective on the material linkage between manufactured capital and natural capital.

  18. Biological Variance in Agricultural Products. Theoretical Considerations

    NARCIS (Netherlands)

    Tijskens, L.M.M.; Konopacki, P.

    2003-01-01

    The food that we eat is uniform neither in shape or appearance nor in internal composition or content. Since technology became increasingly important, the presence of biological variance in our food became more and more of a nuisance. Techniques and procedures (statistical, technical) were

  19. Cholesterol oxidation products and their biological importance

    Czech Academy of Sciences Publication Activity Database

    Kulig, W.; Cwiklik, Lukasz; Jurkiewicz, P.; Rog, T.; Vattulainen, I.

    2016-01-01

    Roč. 199, Sep (2016), s. 144-160 ISSN 0009-3084 R&D Projects: GA ČR(CZ) GBP208/12/G016 Institutional support: RVO:61388963 Keywords : cholesterol * oxidation * oxysterols * biological membranes * biophysical properties Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.361, year: 2016

  20. Synthetic biology for microbial production of lipid-based biofuels.

    Science.gov (United States)

    d'Espaux, Leo; Mendez-Perez, Daniel; Li, Rachel; Keasling, Jay D

    2015-12-01

    The risks of maintaining current CO2 emission trends have led to interest in producing biofuels using engineered microbes. Microbial biofuels reduce emissions because CO2 produced by fuel combustion is offset by CO2 captured by growing biomass, which is later used as feedstock for biofuel fermentation. Hydrocarbons found in petroleum fuels share striking similarity with biological lipids. Here we review synthetic metabolic pathways based on fatty acid and isoprenoid metabolism to produce alkanes and other molecules suitable as biofuels. We further discuss engineering strategies to optimize engineered biosynthetic routes, as well as the potential of synthetic biology for sustainable manufacturing. Published by Elsevier Ltd.

  1. Synthetic biology for microbial production of lipid-based biofuels

    Energy Technology Data Exchange (ETDEWEB)

    d' Espaux, L; Mendez-Perez, D; Li, R; Keasling, JD

    2015-10-23

    The risks of maintaining current CO2 emission trends have led to interest in producing biofuels using engineered microbes. Microbial biofuels reduce emissions because CO2 produced by fuel combustion is offset by CO2 captured by growing biomass, which is later used as feedstock for biofuel fermentation. Hydrocarbons found in petroleum fuels share striking similarity with biological lipids. Here in this paper we review synthetic metabolic pathways based on fatty acid and isoprenoid metabolism to produce alkanes and other molecules suitable as biofuels. Lastly, we further discuss engineering strategies to optimize engineered biosynthetic routes, as well as the potential of synthetic biology for sustainable manufacturing.

  2. New CHP plant for a rubber products manufacturer

    International Nuclear Information System (INIS)

    Vila, R.; Martí, C.

    2016-01-01

    At the end of 2014 the company Industrias de Hule Galgo decided to undertake the installation project of an efficient CHP plant for its production plant, with the aim of bringing down energy costs and improving the company’s competitive position in the market. The new plant has already started its first operational phase. The project has comprised the installation of a single cycle with gas-powered gensets providing a total electrical capacity of 6.6 MW. This provides the necessary thermal oil for the production plant; covers 100% of the electrical power consumed by the industrial complex; and also generates cooling water, giving improved production capacity by supercooling the extrusion system. To execute these works, Industrias de Hule Galgo contracted the services of engineering company AESA to provide the engineering, procurement and construction of the CHP plant. (Author)

  3. Recipes for Men: Manufacturing Makeup and the Politics of Production in 1910s China.

    Science.gov (United States)

    Lean, Eugenia

    2015-01-01

    In the first decade of Republican China (1911-49), masculinity was explored in writings on how to manufacture makeup that appeared in women's magazines. Male authors and editors of these writings--some of whom were connoisseurs of technology, some of whom were would-be manufacturers--appropriated the tropes of the domestic and feminine to elevate hands-on work and explore industry and manufacturing as legitimate masculine pursuits. Tapping into time-honored discourses of virtuous productivity in the inner chambers and employing practices of appropriating the woman's voice to promote unorthodox sentiment, these recipes "feminized" production to valorize a new masculine agenda, which included chemistry and manufacturing, for building a new China.

  4. BIM-Based 4D Simulation to Improve Module Manufacturing Productivity for Sustainable Building Projects

    Directory of Open Access Journals (Sweden)

    Joosung Lee

    2017-03-01

    Full Text Available Modular construction methods, where products are manufactured beforehand in a factory and then transported to the site for installation, are becoming increasingly popular for construction projects in many countries as this method facilitates the use of the advanced technologies that support sustainability in building projects. This approach requires dual factory–site process management to be carefully coordinated and the factory module manufacturing process must therefore be managed in a detailed and quantitative manner. However, currently, the limited algorithms available to support this process are based on mathematical methodologies that do not consider the complex mix of equipment, factories, personnel, and materials involved. This paper presents three new building information modeling-based 4D simulation frameworks to manage the three elements—process, quantity, and quality—that determine the productivity of factory module manufacturing. These frameworks leverage the advantages of 4D simulation and provide more precise information than existing conventional documents. By utilizing a 4D model that facilitates the visualization of a wide range of data variables, manufacturers can plan the module manufacturing process in detail and fully understand the material, equipment, and workflow needed to accomplish the manufacturing tasks. Managers can also access information about material quantities for each process and use this information for earned value management, warehousing/storage, fabrication, and assembly planning. By having a 4D view that connects 2D drawing models, manufacturing errors and rework can be minimized and problems such as construction delays, quality lapses, and cost overruns vastly reduced.

  5. Potential of impulse drying technology for molded pulp products manufacture

    DEFF Research Database (Denmark)

    Didone, Mattia; Tosello, Guido

    2016-01-01

    The vision of the Green Fiber Bottle (GFB) project is to develop a paper bottle for beer, which will be both recyclable and biodegradable. The early prototypes of the bottle are very promising but there are huge technical and scientific challenges ahead to mature the production technology....... The possibility of applying the concept of impulse drying during the drying stage is suggested. This would give benefits in terms of productivity and it would also reduce energy consumption.With the aim of understanding and controlling the impulse drying phenomena, a simplified approach is proposed. Finally......, a potential design for a testing equipment is described....

  6. A practical discussion of risk management for manufacturing of pharmaceutical products.

    Science.gov (United States)

    Mollah, A Hamid; Baseman, Harold S; Long, Mike; Rathore, Anurag S

    2014-01-01

    Quality risk management (QRM) is now a regulatory expectation, and it makes good business sense. The goal of the risk assessment is to increase process understanding and deliver safe and effective product to the patients. Risk analysis and management is an acceptable and effective way to minimize patient risk and determine the appropriate level of controls in manufacturing. While understanding the elements of QRM is important, knowing how to apply them in the manufacturing environment is essential for effective process performance and control. This article will preview application of QRM in pharmaceutical and biopharmaceutical manufacturing to illustrate how QRM can help the reader achieve that objective. There are several areas of risk that a drug company may encounter in pharmaceutical manufacturing, specifically addressing oral solid and liquid formulations. QRM tools can be used effectively to identify the risks and develop strategy to minimize or control them. Risks are associated throughout the biopharmaceutical manufacturing process-from raw material supply through manufacturing and filling operations to final distribution via a controlled cold chain process. Assessing relevant attributes and risks for biotechnology-derived products is more complicated and challenging for complex pharmaceuticals. This paper discusses key risk factors in biopharmaceutical manufacturing. Successful development and commercialization of pharmaceutical products is all about managing risks. If a company was to take zero risk, most likely the path to commercialization would not be commercially viable. On the other hand, if the risk taken was too much, the product is likely to have a suboptimal safety and efficacy profile and thus is unlikely to be a successful product. This article addresses the topic of quality risk management with the key objective of minimizing patient risk while creating an optimal process and product. Various tools are presented to aid implementation of these

  7. Low energy production processes in manufacturing of silicon solar cells

    Science.gov (United States)

    Kirkpatrick, A. R.

    1976-01-01

    Ion implantation and pulsed energy techniques are being combined for fabrication of silicon solar cells totally under vacuum and at room temperature. Simplified sequences allow very short processing times with small process energy consumption. Economic projections for fully automated production are excellent.

  8. Country status of application, manufacturing and sterilization of single-use medical products

    International Nuclear Information System (INIS)

    Norimah Yusof

    1986-01-01

    The paper reviews the current status of application of single-use medical products in Malaysia. The status of their manufacturing and sterilization is also discussed. The increasing production of such items calls for a more reliable and efficient sterilization technique in particular, radiation sterilization. In line with the demand and the effort to increase local production of medical products, UTN would be providing irradiation service together with research and development in this particular field by 1988. (author)

  9. Master data extraction and adaptation based on collected production data in manufacturing execution systems

    OpenAIRE

    Dimitrov, T.; Baumann, M.; Schenk, M.

    2010-01-01

    This paper presents an approach to extraction and correction of manufacturing master data, needed by Manufacturing Execution Systems (MES) to control and schedule the production. The implementation of the created schedule and the improvement of Key Performance Indicators depends strongly on the quality of the master data. The master data of most enterprises ages or the enterprises cannot fully provide it, because a highly manual expense for statistical analysis and administration is needed. T...

  10. Price transmission between products at different stages of manufacturing in forest industries

    Science.gov (United States)

    Mo Zhou; Joseph Buongiorno

    2005-01-01

    The theory of demand and supply implies a positive relationship, or "price transmission" between the prices of products at different stages of manufacturing, This relationship was investigated with quarterly prices of softwood stumpage in the US South, and national prices of forest products, from 1977 to 2002. All prices, net of inflation, were found to be...

  11. Additive manufacturing for the production of inserts for micro injection moulding

    DEFF Research Database (Denmark)

    Mischkot, Michael; Hansen, Hans Nørgaard; Pedersen, David Bue

    2015-01-01

    The production of inserts for micro injection moulding using additive manufacturing technology has the potential to greatly improve the efficiency of pilot production and reduce overall time to market. In this work, Digital Light Processing (DLP) was used to produce micro injection moulding inserts...

  12. On the role of the residual stress state in product manufacturing

    NARCIS (Netherlands)

    Zijlstra, G.; Groen, M.; Post, J.; Ocelik, V.; de Hosson, J.Th.M.

    2016-01-01

    This paper concentrates on the effect of the residual stress state during product manufacturing of AISI 420 steel on the final shape of the product. The work includes Finite Element (FE) calculations of the distribution of the residual stresses after metal forming and a heat treatment. The evolution

  13. Comparative productivity performance in manufacturing in South and East Asia, 1960–93

    NARCIS (Netherlands)

    Timmer, M.P.; Szirmai, A.

    1999-01-01

    This paper focuses on comparative productivity performance in manufacturing in five major Asian economies: China, India, Indonesia, Korea and Taiwan. Using conversion factors derived according to an industry of origin approach, comparisons of real labour productivity are made, with the world

  14. Dropwise additive manufacturing of pharmaceutical products for melt-based dosage forms.

    Science.gov (United States)

    Içten, Elçin; Giridhar, Arun; Taylor, Lynne S; Nagy, Zoltan K; Reklaitis, Gintaras V

    2015-05-01

    The US Food and Drug Administration introduced the quality by design approach and process analytical technology guidance to encourage innovation and efficiency in pharmaceutical development, manufacturing, and quality assurance. As part of this renewed emphasis on the improvement of manufacturing, the pharmaceutical industry has begun to develop more efficient production processes with more intensive use of online measurement and sensing, real-time quality control, and process control tools. Here, we present dropwise additive manufacturing of pharmaceutical products (DAMPP) as an alternative to conventional pharmaceutical manufacturing methods. This mini-manufacturing process for the production of pharmaceuticals utilizes drop on demand printing technology for automated and controlled deposition of melt-based formulations onto edible substrates. The advantages of drop-on-demand technology, including reproducible production of small droplets, adjustable drop sizing, high placement accuracy, and flexible use of different formulations, enable production of individualized dosing even for low-dose and high-potency drugs. In this work, DAMPP is used to produce solid oral dosage forms from hot melts of an active pharmaceutical ingredient and a polymer. The dosage forms are analyzed to show the reproducibility of dosing and the dissolution behavior of different formulations. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  15. VARIANTS OF DETERMINING THE MANUFACTURING COST OF A PRODUCT IN A PRODUCTION UNIT IN THE LIGHT OF BALANCE SHEET LAW

    Directory of Open Access Journals (Sweden)

    Marzena STROJEK‐FILUS

    2014-01-01

    Full Text Available The category of the manufacturing cost of a product is one of the most important ones from the point of view of proper valuation of the assets of a production unit, costs of its operations as well as pricing decisions. This article presents the problem of determining the manufacturing cost of a product in terms of balance sheet law. It has been shown that in order to determine this value various methods and options are allowed by this law, by means of which different values of manufacturing cost of a product are obtained. The importance of a proper selection of an allocation key in setilement of indirect production costs has been highlighted as well as the results of using, in certain cases, approved simplifications in the balance sheet law when determining the manufacturing cost of products have been demonstrated. The problem presented in this article is crucial from the point of view of an organization and management of production as well as managerial decision‐making in a company in the area of design of products and processes.

  16. Additively Manufactured, Net Shape Powder Metallurgy Cans for Valves Used in Energy Production

    Energy Technology Data Exchange (ETDEWEB)

    Peter, William H. [ORNL; Gandy, David [Electric Power Research Institute (EPRI); Lannom, Robert [Oak Ridge National Laboratory (ORNL)

    2018-01-01

    This CRADA NFE-14-05241 was conducted as a Technical Collaboration project within the Oak Ridge National Laboratory (ORNL) Manufacturing Demonstration Facility (MDF) sponsored by the US Department of Energy Advanced Manufacturing Office (CPS Agreement Number 24761). Opportunities for MDF technical collaborations are listed in the announcement “Manufacturing Demonstration Facility Technology Collaborations for US Manufacturers in Advanced Manufacturing and Materials Technologies” posted at http://web.ornl.gov/sci/manufacturing/docs/FBO-ORNL-MDF-2013-2.pdf. The goal of technical collaborations is to engage industry partners to participate in short-term, collaborative projects within the Manufacturing Demonstration Facility (MDF) to assess applicability and of new energy efficient manufacturing technologies. Research sponsored by the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, under contract DE-AC05-00OR22725 with UT-Battelle, LLC.ORNL would like to acknowledge the leadership of EPRI in pulling together the extensive team and managing the execution of the project. In addition, ORNL would like to acknowledge the other contributions of the team members associated with this project. Quintus provided time, access, expertise, and labor of their hydro forming capabilities to evaluate both conventional and additively manufactured tools through this process. Crane ChemPharma Energy provided guidance and information on valve geometries. Carpenter Powder Products was involved with the team providing information on powder processing as it pertains to the canning and hot isostatic pressing of powder. on providing powder and knowledge as it pertains to powder supply for hot isostatic pressing; they also provided powder for the test trials by the industrial team. Bodycote provided guidance on hot isostatic pressing and can requirements. They were also responsible for the hot isostatic pressing of the test valve

  17. Biological hydrogen production from industrial wastewaters

    Energy Technology Data Exchange (ETDEWEB)

    Peixoto, Guilherme; Pantoja Filho, Jorge Luis Rodrigues; Zaiat, Marcelo [Universidade de Sao Paulo (EESC/USP), Sao Carlos, SP (Brazil). School of Engineering. Dept. Hydraulics and Sanitation], Email: peixoto@sc.usp.br

    2010-07-01

    This research evaluates the potential for producing hydrogen in anaerobic reactors using industrial wastewaters (glycerol from bio diesel production, wastewater from the parboilization of rice, and vinasse from ethanol production). In a complementary experiment the soluble products formed during hydrogen production were evaluated for methane generation. The assays were performed in batch reactors with 2 liters volume, and sucrose was used as a control substrate. The acidogenic inoculum was taken from a packed-bed reactor used to produce hydrogen from a sucrose-based synthetic substrate. The methanogenic inoculum was taken from an upflow anaerobic sludge blanket reactor treating poultry slaughterhouse wastewater. Hydrogen was produced from rice parboilization wastewater (24.27 ml H{sub 2} g{sup -1} COD) vinasse (22.75 ml H{sub 2} g{sup -1} COD) and sucrose (25.60 ml H{sub 2} g{sup -1} COD), while glycerol only showed potential for methane generation. (author)

  18. 9 CFR 114.18 - Reprocessing of biological products.

    Science.gov (United States)

    2010-01-01

    ... for all tests conducted shall be submitted to Animal and Plant Health Inspection Service. The licensee... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Reprocessing of biological products. 114.18 Section 114.18 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE...

  19. 9 CFR 102.5 - U.S. Veterinary Biological Product License.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false U.S. Veterinary Biological Product... BIOLOGICAL PRODUCTS § 102.5 U.S. Veterinary Biological Product License. (a) Authorization to produce each biological product shall be specified on a U.S. Veterinary Biological Product License, issued by the...

  20. Cholesterol oxidation products and their biological importance

    DEFF Research Database (Denmark)

    Kulig, Waldemar; Cwiklik, Lukasz; Jurkiewicz, Piotr

    2016-01-01

    The main biological cause of oxysterols is the oxidation of cholesterol. They differ from cholesterol by the presence of additional polar groups that are typically hydroxyl, keto, hydroperoxy, epoxy, or carboxyl moieties. Under typical conditions, oxysterol concentration is maintained at a very low...... and precisely regulated level, with an excess of cholesterol. Like cholesterol, many oxysterols are hydrophobic and hence confined to cell membranes. However, small chemical differences between the sterols can significantly affect how they interact with other membrane components, and this in turn can have...

  1. 27 CFR 19.58 - Use of taxpaid distilled spirits to manufacture products unfit for beverage use.

    Science.gov (United States)

    2010-04-01

    ... spirits to manufacture products unfit for beverage use. 19.58 Section 19.58 Alcohol, Tobacco Products and... taxpaid distilled spirits to manufacture products unfit for beverage use. (a) General. Apothecaries... distilled spirits contained therein: (1) Medicines, medicinal preparations, food products, flavors...

  2. Biocomes: new biological products for sustainable farming and forestry

    NARCIS (Netherlands)

    Teixidó, N.; Cal, de A.L.; Usall, J.; Guijarro, B.; Larena, I.; Torres, R.; Abadias, M.; Köhl, J.

    2016-01-01

    The growing interest in biological control has been reflected during last decades in a big number of scientific publications, books and symposia. However, biocontrol commercial application at a European level is limited and biological control products are not currently available for the control of

  3. Versatile and on-demand biologics co-production in yeast.

    Science.gov (United States)

    Cao, Jicong; Perez-Pinera, Pablo; Lowenhaupt, Ky; Wu, Ming-Ru; Purcell, Oliver; de la Fuente-Nunez, Cesar; Lu, Timothy K

    2018-01-08

    Current limitations to on-demand drug manufacturing can be addressed by technologies that streamline manufacturing processes. Combining the production of two or more drugs into a single batch could not only be useful for research, clinical studies, and urgent therapies but also effective when combination therapies are needed or where resources are scarce. Here we propose strategies to concurrently produce multiple biologics from yeast in single batches by multiplexing strain development, cell culture, separation, and purification. We demonstrate proof-of-concept for three biologics co-production strategies: (i) inducible expression of multiple biologics and control over the ratio between biologic drugs produced together; (ii) consolidated bioprocessing; and (iii) co-expression and co-purification of a mixture of two monoclonal antibodies. We then use these basic strategies to produce drug mixtures as well as to separate drugs. These strategies offer a diverse array of options for on-demand, flexible, low-cost, and decentralized biomanufacturing applications without the need for specialized equipment.

  4. Real-Time Shop-Floor Production Performance Analysis Method for the Internet of Manufacturing Things

    Directory of Open Access Journals (Sweden)

    Yingfeng Zhang

    2014-04-01

    Full Text Available Typical challenges that manufacturing enterprises are facing now are compounded by lack of timely, accurate, and consistent information of manufacturing resources. As a result, it is difficult to analyze the real-time production performance for the shop-floor. In this paper, the definition and overall architecture of the internet of manufacturing things is presented to provide a new paradigm by extending the techniques of internet of things (IoT to manufacturing field. Under this architecture, the real-time primitive events which occurred at different manufacturing things such as operators, machines, pallets, key materials, and so forth can be easily sensed. Based on these distributed primitive events, a critical event model is established to automatically analyze the real-time production performance. Here, the up-level production performance analysis is regarded as a series of critical events, and the real-time value of each critical event can be easily calculated according to the logical and sequence relationships among these multilevel events. Finally, a case study is used to illustrate how to apply the designed methods to analyze the real-time production performance.

  5. A new integrated lean manufacturing model for magnesium products

    Science.gov (United States)

    D'Errico, F.; Perricone, G.; Oppio, R.

    2009-04-01

    From an environmental point of view, lighter metals like aluminum and magnesium are unclean products to make; they require energy-intensive methods and increased greenhouse gas emissions as compared with steels. They are, however, clean to use, in particular in the transportation sector, if adequate weight savings and consequent fuel consumption reduction and CO2 reduction can be achieved to offset the initial higher energy need. In order to reduce CO2 emissions, better energy efficiency and substitution of low-carbon technologies are going to play a key role in future technical options. Modern research and development should be focused on promoting the efficient use of metallic materials according to the “dematerialization” concept design.

  6. Perception of the HACCP system operators on livestock product manufacturers.

    Science.gov (United States)

    Kim, Jung-Hyun; Nam, Ki-Chang; Jo, Cheorun; Lim, Dong-Gyun

    2014-01-01

    The purpose of this study was to investigate crucial factors on HACCP system implementation in domestic livestock product plants, and to offer job satisfaction and the career prospect of HACCP system operators. The survey was carried out by selecting 150 HACCP system operators who implemented HACCP system. The respondents claimed that the most important contents in HACCP system operation were to assemble HACCP team (21.8%), and the second was to monitoring (20.0%). Documentation and recording (16.9%) and verification (11.1%) were followed. The respondents answered the major factor in sanitation management was cleaning/washing/disinfection (18.9%) and inspection (18.4%). The results showed that there were significant differences in the prospect of occupation in HACCP system operator by the gender (p HACCP system operator were satisfied with their job (73%) and also showed optimistic prospect of occupation (82%).

  7. Systems Biology in Animal Production and Health

    DEFF Research Database (Denmark)

    for improved animal production and health. The book will contain online resources where additional data and programs can be accessed. Some chapters also come with computer programming codes and example datasets to provide readers hands-on (computer) exercises. This second volume deals with integrated modeling...... and analyses of multi-omics datasets from theoretical and computational approaches and presents their applications in animal production and health as well as veterinary medicine to improve diagnosis, prevention and treatment of animal diseases. This book is suitable for both students and teachers in animal...

  8. Biological productivity, terrigenous influence and noncrustal ...

    Indian Academy of Sciences (India)

    1100ka. Our data suggest that during ~ 1100 ka and ~ 400 ka siliceous productivity was lower, ... Manganese, Ba, Cu, Ni, Zn, and Co have around 90% of their supply from noncrustal ...... Pattan J N, Masuzawa T, Divakar Naidu P, Parthiban G.

  9. Linking neuroethology to the chemical biology of natural products

    DEFF Research Database (Denmark)

    Olivera, Baldomero M.; Raghuraman, Shrinivasan; Schmidt, Eric W.

    2017-01-01

    From a biological perspective, a natural product can be defined as a compound evolved by an organism for chemical interactions with another organism including prey, predator, competitor, pathogen, symbiont or host. Natural products hold tremendous potential as drug leads and have been extensively...... a better understanding of the evolution, biology and biochemistry of natural products will facilitate both neuroscience and the potential for drug leads. The larger goal is to establish a new sub-discipline in the broader field of neuroethology that we refer to as “Chemical Neuroethology”, linking...... the substantial work carried out by chemists on natural products with accelerating advances in neuroethology....

  10. Trade Liberalization and Productivity-A Panel Study of the Mexican Manufacturing Industry

    OpenAIRE

    Talan Iscan

    1998-01-01

    In recent years there has been a revival of interest in the trade-growth nexus. A number of authors have suggested that regional economic integration and liberalization of international trade are likely to have positive effects not only on productivity levels but also on long-term productivity growth rates in developing countries. Using a panel of Mexican manufacturing industries, this paper examines several alternative mechanisms through which trade contributes positively to productivity lev...

  11. WTO Accession, Foreign Bank Entry, and the Productivity of Chinese Manufacturing Firms

    DEFF Research Database (Denmark)

    Lai, Tat-kei; Qian, Zhenjie; Wang, Luhang

    2016-01-01

    After China’s accession to the World Trade Organization (WTO) in December 2001, foreign banks are allowed to enter the Chinese banking market in phases. Using firm-level data from the National Bureau of Statistics of China which cover all state-owned and non state-owned manufacturing firms...... with sales over 5 million RMB, we examine the relationship between foreign bank entry and the industry-level productivity growth of China’s manufacturing sector. Our empirical results suggest that (a) on average, opening up a region for foreign bank entry has no impact on aggregate productivity growth, (b...

  12. Product recovery optimization in closed-loop supply chain to improve sustainability in manufacturing

    DEFF Research Database (Denmark)

    Govindan, Kannan; Jha, P. C.; Garg, Kiran

    2016-01-01

    that emerge from that business’s economical, environmental and social dimensions. In this paper, we propose a multi-objective mixed integer mathematical problem for a generic closed-loop supply chain (CLSC) network to rationalise how a system’s product recovery helps to improve manufacturing sustainability....... The CLSC network proposed in this study consists of a hybrid manufacturing facility, warehouse, distribution centres, collection centres and a hybrid recovery facility (HRF). The proposed model determines the best location for the HRF and optimal flow of products, recovered parts and material...

  13. SURVEY REGARDING THE LEVEL OF PRODUCT LIFECYCLE MANAGEMENT IN MANUFACTURING COMPANIES

    Directory of Open Access Journals (Sweden)

    František Freiberg

    2011-12-01

    Full Text Available This article is about a questionnaire survey regarding the level of product lifecycle management in manufacturing companies in the Czech Republic. Based on the research available from foreign and domestic literature, a questionnaire survey was compiled and carried out with the purpose of applying the methods used in the life cycle management in selected areas: maintenance, information systems and the cost of the product lifecycle. The survey is carried out through a printed as well as an electronic questionnaire with additional structured interviews in selected manufacturing companies in the Czech Republic, Slovak Republic and Romania.

  14. Manufacture of power station heat exchangers using modern production technology

    International Nuclear Information System (INIS)

    Genzlinger, W.; Hoffmann, J.; Ohlhaeuser, K.

    1986-01-01

    Heat exchangers of high quality and operational safety can only be fabricated economically if fabrication is as 'simple' as possible and can be controlled and if, through value analysis, the work flows can be mechanized and automated and the following requirements are met: use of materials that are easy to work with for the application considered, choice of product designs and wall thicknesses that offer favourable conditions for processing and non-destructive testing, placing of seams in such a way that good accessibility for welding and minimum residual welding stresses are assured, minimizing the number of welding seams, use of automatic welding machines for submerged-arc welding and electronically controlled sources of welding current - semi-automatic equipment for spatter-free interfaces (pulse technique), electronically controlled equipment for welding in rollers and pipes and CNC-controlled machining centres for drilling pipe galleries (deep-hole drilling) and baffle plates and for machining the sealing elements after welding. Continuous inspections in each phase of fabrication assures that heat exchangers are made which fully meet the requirements of nuclear power station operators. (orig.)

  15. Biological production of liquid fuels from biomass

    Energy Technology Data Exchange (ETDEWEB)

    None

    1982-01-01

    A scheme for the production of liquid fuels from renewable resources such as poplar wood and lignocellulosic wastes from a refuse hydropulper was investigated. The particular scheme being studied involves the conversion of a cellulosic residue, resulting from a solvent delignified lignocellulosic feed, into either high concentration sugar syrups or into ethyl and/or butyl alcohol. The construction of a pilot apparatus for solvent delignifying 150 g samples of lignocellulosic feeds was completed. Also, an analysis method for characterizing the delignified product has been selected and tested. This is a method recommended in the Forage Fiber Handbook. Delignified samples are now being prepared and tested for their extent of delignification and susceptibility to enzyme hydrolysis. Work is continuing on characterizing the cellulase and cellobiase enzyme systems derived from the YX strain of Thermomonospora.

  16. Biological production of gas from farmyard manure

    Energy Technology Data Exchange (ETDEWEB)

    Scheffer, F; Kemmler, G

    1953-01-08

    Under anaerobic conditions of farmyard-manure storage, the products include organic acids from which methane is formed. The Schmidt-Eggersgluss method is described in which 5 to 7m/sup 3/ of gas is formed per 100 kg of fresh manure, without loss of N, P, K, or Ca from the residual sludge which is of high nutrient content. Large N losses occur if the sludge comes long in contact with atmosphere.

  17. Dropwise additive manufacturing of pharmaceutical products for solvent-based dosage forms.

    Science.gov (United States)

    Hirshfield, Laura; Giridhar, Arun; Taylor, Lynne S; Harris, Michael T; Reklaitis, Gintaras V

    2014-02-01

    In recent years, the US Food and Drug Administration has encouraged pharmaceutical companies to develop more innovative and efficient manufacturing methods with improved online monitoring and control. Mini-manufacturing of medicine is one such method enabling the creation of individualized product forms for each patient. This work presents dropwise additive manufacturing of pharmaceutical products (DAMPP), an automated, controlled mini-manufacturing method that deposits active pharmaceutical ingredients (APIs) directly onto edible substrates using drop-on-demand (DoD) inkjet printing technology. The use of DoD technology allows for precise control over the material properties, drug solid state form, drop size, and drop dynamics and can be beneficial in the creation of high-potency drug forms, combination drugs with multiple APIs or individualized medicine products tailored to a specific patient. In this work, DAMPP was used to create dosage forms from solvent-based formulations consisting of API, polymer, and solvent carrier. The forms were then analyzed to determine the reproducibility of creating an on-target dosage form, the morphology of the API of the final form and the dissolution behavior of the drug over time. DAMPP is found to be a viable alternative to traditional mass-manufacturing methods for solvent-based oral dosage forms. © 2013 Wiley Periodicals, Inc. and the American Pharmacists Association.

  18. Product manufacturing, quality, and reliability initiatives to maintain a competitive advantage and meet customer expectations in the semiconductor industry

    Science.gov (United States)

    Capps, Gregory

    Semiconductor products are manufactured and consumed across the world. The semiconductor industry is constantly striving to manufacture products with greater performance, improved efficiency, less energy consumption, smaller feature sizes, thinner gate oxides, and faster speeds. Customers have pushed towards zero defects and require a more reliable, higher quality product than ever before. Manufacturers are required to improve yields, reduce operating costs, and increase revenue to maintain a competitive advantage. Opportunities exist for integrated circuit (IC) customers and manufacturers to work together and independently to reduce costs, eliminate waste, reduce defects, reduce warranty returns, and improve quality. This project focuses on electrical over-stress (EOS) and re-test okay (RTOK), two top failure return mechanisms, which both make great defect reduction opportunities in customer-manufacturer relationship. Proactive continuous improvement initiatives and methodologies are addressed with emphasis on product life cycle, manufacturing processes, test, statistical process control (SPC), industry best practices, customer education, and customer-manufacturer interaction.

  19. A field survey of chemicals and biological products used in shrimp farming

    International Nuclear Information System (INIS)

    Graeslund, S.; Holmstroem, K.; Wahlstroem, A.

    2003-01-01

    This study documented the use of chemicals and biological products in marine and brackish water shrimp farming in Thailand, the world's top producer of farmed shrimp. Interviews were conducted with 76 shrimp farmers in three major shrimp producing regions, the eastern Gulf coast, the southern Gulf coast and the Andaman coast area. Farmers in the study used on average 13 different chemicals and biological products. The most commonly used products were soil and water treatment products, pesticides and disinfectants. Farmers in the southern Gulf coast area used a larger number of products than farmers in the other two areas. In the study, the use of more than 290 different chemicals and biological products was documented. Many of the pesticides, disinfectants and antibiotics used by the farmers could have negative effects on the cultured shrimps, cause a risk for food safety, occupational health, and/or have negative effects on adjacent ecosystems. Manufacturers and retailers of the products often neglected to provide farmers with necessary information regarding active ingredient and relevant instructions for safe and efficient use

  20. Applying Value Stream Mapping Technique for Production Improvement in a Manufacturing Company: A Case Study

    Science.gov (United States)

    Jeyaraj, K. L.; Muralidharan, C.; Mahalingam, R.; Deshmukh, S. G.

    2013-01-01

    The purpose of this paper is to explain how value stream mapping (VSM) is helpful in lean implementation and to develop the road map to tackle improvement areas to bridge the gap between the existing state and the proposed state of a manufacturing firm. Through this case study, the existing stage of manufacturing is mapped with the help of VSM process symbols and the biggest improvement areas like excessive TAKT time, production, and lead time are identified. Some modifications in current state map are suggested and with these modifications future state map is prepared. Further TAKT time is calculated to set the pace of production processes. This paper compares the current state and future state of a manufacturing firm and witnessed 20 % reduction in TAKT time, 22.5 % reduction in processing time, 4.8 % reduction in lead time, 20 % improvement in production, 9 % improvement in machine utilization, 7 % improvement in man power utilization, objective improvement in workers skill level, and no change in the product and semi finished product inventory level. The findings are limited due to the focused nature of the case study. This case study shows that VSM is a powerful tool for lean implementation and allows the industry to understand and continuously improve towards lean manufacturing.

  1. QUALITY CONTROL IN PRECAST PRODUCTION A case study on Tunnel Segment Manufacture

    Directory of Open Access Journals (Sweden)

    Yee Weng Cheong

    2005-01-01

    Full Text Available Quality control forms an integral part of precast production. An efficient quality system is most critical in the mass production of precast components in any project. In this study, the quality control system implemented in a precast factory is discussed. The precast factory is set up for the manufacture of large quantity of tunnel segments under a contract. Processes in the precast manufacture are discussed with respect to the control procedures in the quality inspection plan. The standard tests involved, roles of inspectors and corrective actions on-site are highlighted. Critical issues pertaining to the productivity and quality of precast production are reviewed. These include the quality of staff and maintenance, which could potentially affect the efficiency of the quality system. Some considerations should also be given to improve the workflow and productivity of the plant.

  2. BIOLOGICALLY ACTIVE SUBSTANCES OF SPIRIT PRODUCTION WASTE

    Directory of Open Access Journals (Sweden)

    A. S. Kayshev

    2014-01-01

    Full Text Available A content of biologically active compounds (BAC with signified pharmacological activity in distillers grains was proved. It is prospective for applications of these grains as a raw material resource of pharmaceuticals. A composition of BAC distillers grains received from wheat, corn, barley, millet at different spirit enterprises which use hydro fermentative grain processing. Considering polydispersity of distillers grains they were separated on solid and liquid phases preliminary. Physical and chemical characteristics of distillers grains' liquid base were identified. Elementary composition of distillers grains is signified by active accumulation of biogenic elements (phosphorus, potassium, magnesium, calcium, sodium, iron and low content of heavy metals. The solid phase of distillers grains accumulates carbon, hydrogen and nitrogen in high concentration. The liquid phase of distillers grains contains: proteins and amino acids (20-46%, reducing sugars (5,6%-17,5%, galacturonides (0,8-1,4%, ascorbic acid (6,2-11,4 mg%. The solid base of distillers grains contains: galacturonides (3,4-5,3%, fatty oil (8,4-11,1% with predomination of essential fatty acids, proteins and amino acids (2,1-2,5%, flavonoids (0,4-0,9%, tocopherols (3,4-7,7 mg%. A method of complex processing of distillers grains based on application of membrane filtering of liquid phase and liquid extraction by inorganic and organic solvents of solid phase, which allows almost full extraction of the sum of biologically active compounds (BAC from liquid phase (Biobardin BM and solid phase (Biobardin UL. Biobardin BM comprises the following elements: proteins and amino acids (41-69%, reducing sugars (3,5-15,6%, fatty oil (0,2-0,3%, flavonoids (0,2-0,7%, ascorbic acid (17-37 mg%. Biobardin UL includes: oligouronids (16,4-19,5%, proteins and amino acids (11-21%, fatty oil (3,2-4,9% which includes essential acids; flavonoids (0,6-1,5%, tocopherols (6,6-10,2 mg%, carotinoids (0,13-0,21 mg

  3. Analysis of the influence of advanced materials for aerospace products R and D and manufacturing cost

    International Nuclear Information System (INIS)

    Shen, A W; Guo, J L; Wang, Z J

    2015-01-01

    In this paper, we pointed out the deficiency of traditional cost estimation model about aerospace products Research and Development (R and D) and manufacturing based on analyzing the widely use of advanced materials in aviation products. Then we put up with the estimating formulas of cost factor, which representing the influences of advanced materials on the labor cost rate and manufacturing materials cost rate. The values ranges of the common advanced materials such as composite materials, titanium alloy are present in the labor and materials two aspects. Finally, we estimate the R and D and manufacturing cost of F/A-18, F/A- 22, B-1B and B-2 aircraft based on the common DAPCA IV model and the modified model proposed by this paper. The calculation results show that the calculation precision improved greatly by the proposed method which considering advanced materials. So we can know the proposed method is scientific and reasonable. (paper)

  4. Analysis of the influence of advanced materials for aerospace products R&D and manufacturing cost

    Science.gov (United States)

    Shen, A. W.; Guo, J. L.; Wang, Z. J.

    2015-12-01

    In this paper, we pointed out the deficiency of traditional cost estimation model about aerospace products Research & Development (R&D) and manufacturing based on analyzing the widely use of advanced materials in aviation products. Then we put up with the estimating formulas of cost factor, which representing the influences of advanced materials on the labor cost rate and manufacturing materials cost rate. The values ranges of the common advanced materials such as composite materials, titanium alloy are present in the labor and materials two aspects. Finally, we estimate the R&D and manufacturing cost of F/A-18, F/A- 22, B-1B and B-2 aircraft based on the common DAPCA IV model and the modified model proposed by this paper. The calculation results show that the calculation precision improved greatly by the proposed method which considering advanced materials. So we can know the proposed method is scientific and reasonable.

  5. Feasibility of commercial space manufacturing, production of pharmaceuticals. Volume 2: Technical analysis

    Science.gov (United States)

    1978-01-01

    A technical analysis on the feasibility of commercial manufacturing of pharmaceuticals in space is presented. The method of obtaining pharmaceutical company involvement, laboratory results of the separation of serum proteins by the continuous flow electrophoresis process, the selection and study of candidate products, and their production requirements is described. The candidate products are antihemophilic factor, beta cells, erythropoietin, epidermal growth factor, alpha-1-antitrypsin and interferon. Production mass balances for antihemophelic factor, beta cells, and erythropoietin were compared for space versus ground operation. A conceptual description of a multiproduct processing system for space operation is discussed. Production requirements for epidermal growth factor of alpha-1-antitrypsin and interferon are presented.

  6. Supply Inventory Management: Evaluation of the Defense Supply Center Columbus Qualified Products List and Qualified Manufacturers List Program

    National Research Council Canada - National Science Library

    2002-01-01

    ... was transitioned from the Military Departments. The Defense Supply Center Columbus currently has management responsibility for over 300 Qualified Products Lists and 4 Qualified Manufacturers Lists...

  7. INNOVATIONS AS AN IMPORTANT FACTOR INFLUENCING LABOUR PRODUCTIVITY IN THE MANUFACTURING INDUSTRY

    Directory of Open Access Journals (Sweden)

    Marija Bušelić

    2016-12-01

    Full Text Available Economic science has long recognized labour productivity as an important factor of economic growth. In the uncertain conditions of increasingly fierce and complex competition, it becomes one of the key prerequisites for an adequate response to global challenges. The development of labour productivity has to be observed as a multi-dimensional process including numerous interconnected quantitative and qualitative factors, in particular human factors and technological advancement realized through investments in research and development (innovations. The analysis of labour productivity in the manufacturing industry of the selected countries, Germany and China, is performed in the context of an important influential factor – innovations, and interdependently with the economic growth of the selected countries. The research results and the conducted regression analyses indicate a superiority of German labour productivity in the manufacturing industry, which is strongly affected by considerable investments in research and development. However, the technological convergence of China as the upcoming power is increasingly important, which shows that the gap in labour productivity is decreasing, making developed countries face new challenges posed by globalization. The analysis of the interdependence of economic growth (GDP and labour productivity in the manufacturing industry points to a positive link and the conclusion that the elasticity of the GDP to changes in labour productivity is greater in China than in Germany.

  8. Orodispersible films: Product transfer from lab-scale to continuous manufacturing.

    Science.gov (United States)

    Thabet, Yasmin; Breitkreutz, Joerg

    2018-01-15

    Orodispersible films have been described as new beneficial dosage forms for special patient populations. Due to various production settings, different requirements on film formulations are required for non- continuous and continuous manufacturing. In this study, a continuous coating machine was qualified in regards of the process conditions for film compositions and their effects on the formed films. To investigate differences between both manufacturing processes, various film formulations of hydrochlorothiazide and hydroxypropylcellulose (HPC) or hydroxypropylmethycellulose (HPMC) as film formers were produced and the resulting films were characterized. The qualification of the continuously operating coating machine reveals no uniform heat distribution during drying. Coating solutions for continuous manufacturing should provide at least a dynamic viscosity of 1 Pa*s (wet film thickness of 500 μm, velocity of 15.9 cm/min). HPC films contain higher residuals of ethanol or acetone in bench-scale than in continuous production mode. Continuous production lead to lower drug content of the films. All continuously produced films disintegrate within less than 30 s. There are observed significant effects of the production process on the film characteristics. When transferring film manufacturing from lab-scale to continuous mode, film compositions, processing conditions and suitable characterization methods have to be carefully selected and adopted. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Does Lean Production Sacrifice Learning in a Manufacturing Environment? An Action Learning Case Study.

    Science.gov (United States)

    Scott, Fiona M.; Butler, Jim; Edwards, John

    2001-01-01

    An action learning program was implemented by a manufacturer using lean production practices. Action learning practices were accommodated during times of stability, but abandoned in times of crisis. The meaning of work in this organizational culture excluded all practices, such as reflection, that were not visible and targeted at immediate…

  10. The transformation factor: a measure for the productive behaviour of a manufacturing process

    NARCIS (Netherlands)

    Ron, de A.J.

    1993-01-01

    By using advanced manufacturing processes, production results should increase. Nevertheless managers have their doubts to invest in such processes because of the financial risks and the absence of adequate technical and economical measures which should support their decisions. Measures which contain

  11. Additive Manufacturing and Casting Technology Comparison: Mechanical Properties, Productivity and Cost Benchmark

    Science.gov (United States)

    Vevers, A.; Kromanis, A.; Gerins, E.; Ozolins, J.

    2018-04-01

    The casting technology is one of the oldest production technologies in the world but in the recent years metal additive manufacturing also known as metal 3D printing has been evolving with huge steps. Both technologies have capabilities to produce parts with internal holes and at first glance surface roughness is similar for both technologies, which means that for precise dimensions parts have to be machined in places where precise fit is necessary. Benchmark tests have been made to find out if parts which are produced with metal additive manufacturing can be used to replace parts which are produced with casting technology. Most of the comparative tests have been made with GJS-400-15 grade which is one of the most popular cast iron grades. To compare mechanical properties samples have been produced using additive manufacturing and tested for tensile strength, hardness, surface roughness and microstructure and then the results have been compared with the samples produced with casting technology. In addition, both technologies have been compared in terms of the production time and production costs to see if additive manufacturing is competitive with the casting technology. The original paper has been written in the Latvian language as part of the Master Thesis within the framework of the production technology study programme at Riga Technical University.

  12. 75 FR 4973 - Registration Requirements for Importers and Manufacturers of Prescription Drug Products...

    Science.gov (United States)

    2010-02-01

    ... diverted to the clandestine manufacture of a controlled substance. Most of the ephedrine, pseudoephedrine... for-profit. Other: Not-for-profit, government agencies. Abstract: The Domestic Chemical Diversion... may be diverted in the United States for the production of illicit drugs must register with DEA...

  13. Process for manufacture of inertial confinement fusion targets and resulting product

    International Nuclear Information System (INIS)

    Solomon, D.E.; Wise, K.D.; Wuttke, G.H.; Masnari, N.A.; Rensel, W.B.; Robinson, M.G.

    1980-01-01

    A method of manufacturing inertial confinement fusion targets is described which is adaptable for high volume production of low cost targets in a wide variety of sizes. The targets include a spherical pellet of fusion fuel surrounded by a protective concentric shell. (UK)

  14. Lean Production Control at a High-Variety, Low-Volume Parts Manufacturer

    NARCIS (Netherlands)

    Bokhorst, Jos A. C.; Slomp, Jannes

    2010-01-01

    Eaton Electric General Supplies, a parts manufacturing unit that supplies parts for Eaton's electrical business unit, implemented several lean control elements in its high-variety, low-volume production units. These control elements include a constant work-in-process mechanism to limit and control

  15. Towards an integration of process planning and production planning and control for flexible manufacturing systems

    NARCIS (Netherlands)

    Gaalman, GJC; Slomp, J; Suresh, NC

    This introduction article attempts to present some major issues relating to the integration of process planning and production planning and control (PPC) for flexible manufacturing systems (FMSs). It shows that the performance of an FMS can be significantly improved and FMS capabilities more

  16. A Comparison of Real Output and Productivity for British and American Manufacturing in 1935

    NARCIS (Netherlands)

    Jong, H. de; Woltjer, P.

    2009-01-01

    The manufacturing productivity gap between the U.S. and the U.K. became much larger during the interwar period than existing estimates suggest. This paper presents a new estimate based on real value added and hours worked. First, a detailed benchmark comparison for 1935 is constructed using official

  17. Enabling Manufacturing Competitiveness and Economic Sustainability : Proceedings of the 4th International Conference on Changeable, Agile, Reconfigurable and Virtual production

    CERN Document Server

    2012-01-01

    The changing manufacturing environment requires more responsive and adaptable manufacturing systems. The theme of the 4th International Conference on Changeable, Agile, Reconfigurable and Virtual production (CARV2011) is “Enabling Manufacturing Competitiveness and Economic Sustainability”. Leading edge research and best implementation practices and experiences, which address these important issues and challenges, are presented. The proceedings include advances in manufacturing systems design, planning, evaluation, control and evolving paradigms such as mass customization, personalization, changeability, re-configurability and flexibility. New and important concepts such as the dynamic product families and platforms, co-evolution of products and systems, and methods for enhancing manufacturing systems’ economic sustainability and prolonging their life to produce more than one product generation are treated. Enablers of change in manufacturing systems, production volume and capability scalability and man...

  18. Product Development Categorized as Independent Strategic and Innovative Practice: Case from Indian Manufacturing

    Directory of Open Access Journals (Sweden)

    Himanshu Dutt

    2008-06-01

    Full Text Available In recent time, Indian manufacturing has seen technologically intensive and resource optimization based initiatives to satisfy competitive urge and to build or sustain market position. This they do by developing products either strategically or innovatively, but that is hardly distinguished or seen as a separate approach to product development. Strategically, product development is resource optimization based while innovatively, it is product differentiation focused. This paper outlines the strategic and innovative approach to product development and analyzes sector specific role of each in product development. The study is undertaken with nine product development team-leaders and resource-heads, three of each from automobile, steel and textile. It is concluded that textile is strategically skewed toward product development whereas automobile is inclined towards innovative orientation. The biggest limitation of this study is smaller sample-size because respondents are reluctant to disclose new technical initiatives and composition of product development.

  19. Study on the Key Factor Parameters to Increase Productivity in Construction and Manufacturing Industries.

    Science.gov (United States)

    Almazyed, K.; Alaswad, A.; Olabi, A. G.

    2016-02-01

    Proper management of human and non-human resources in construction and manufacturing projects can give-in considerable savings in time and cost. Construction and Manufacturing industry faces issues in connection with problems related with productivity and the problems are usually connected with performance of employees. The performance of employees is affected by many factors. In this paper a survey was made on respondents who are employed various projects of Saudi Arabia. The researcher developed a theoretical framework from the existing research which was used as a Model to collect and analyze the field data to test the hypothesis. In this research activity three predictors (commitment, job satisfaction and job performance) for determining the change in productivity. The results highlight that commitment and job performance (respectively) are the two predictors which are explaining 37% of variation in the productivity of the companies. The results also show that Job Satisfaction has no role in the prediction of productivity.

  20. Validation of cross-contamination control in biological safety cabinet for biotech/pharmaceutical manufacturing process.

    Science.gov (United States)

    Hu, Shih-Cheng; Shiue, Angus; Tu, Jin-Xin; Liu, Han-Yang; Chiu, Rong-Ben

    2015-12-01

    For class II, type A2 biological safety cabinets (BSC), NSF/ANSI Standard 49 should be conformed in cabinet airflow velocity derivation, particle contamination, and aerodynamic flow properties. However, there exists a potential problem. It has been built that the cabinet air flow stabilize is influenced by the quantity of downflow of air and the height above the cabinet exhaust opening. Three air downflow quantities were compared as an operating apparatus was placed from 20 to 40 cm above the bench of the cabinet. The results show that the BSC air downflow velocity is a function of increased sampling height, displaying that containment is improvingly permitted over product protection as the sampling height decreases. This study investigated the concentration gradient of particles at various heights and downflow air quantity from the bench of the BSC. Experiment results indicate that performance near the bench was better than in the rest of the BSC. In terms of height, the best cleanliness was measured at a height of 10 cm over the bench; it reduced actually with add in height. The empirical curves accommodate, founded on the concentration gradient of particle created was elaborated for evaluating the particle concentration at different heights and downflow air quantity from the source of the bench of the BSC. The particle image velocimetry system applied for BSC airflow research to fix amount of airflow patterns and air distribution measurement and results of measurements show how obstructions can greatly influence the airflow and contaminant transportation in a BSC.

  1. Gender Pay Gap, Productivity Gap and Discrimination in Canadian Clothing Manufacturing in 1870

    OpenAIRE

    Catherine L McDevitt; James R Irwin; Kris Inwood

    2009-01-01

    Women's earnings were less than men's in Canadian clothing factories in 1870. Orthodox neoclassical theory would explain that gender pay gap as a reflection of a gender productivity gap. Using classical hypothesis testing we reject that view, based on a large cross-section of 1870 census data. We find the gender pay gap was significantly larger than the gender productivity gap, much as Hellerstein et al. [1999] found for US manufacturing circa 1990. Our results are clear and compell...

  2. Integrate Product Planning Process of OKP Companies in the Cloud Manufacturing Environment

    OpenAIRE

    Zheng , Pai; Xu , Xun; Xie , Sheng ,

    2015-01-01

    Part 8: Cloud-Based Manufacturing; International audience; In today’s competitive market, OKP companies operate in the “engineer-to-order” business mode, whereby analysing the “voice of customer” promptly and accurately in the early design stage determines the success of product development. However, OKP companies have limited resources. They may not be able to afford the cost of the complicated Quality Function Deployment (QFD) product planning process, nor can they obtain abundant CRs infor...

  3. An integrated approach for safer, productive and reliable PHWR fuel manufacturing at NFC

    International Nuclear Information System (INIS)

    Saibaba, N.

    2013-01-01

    India has been pursuing three-stage nuclear power programme and has developed comprehensive capabilities in all aspects of nuclear power and fuel cycle and is now recognized as a country with advanced nuclear technologies in the comity of nations. The first stage of Pressurized Heavy Water Reactors (PHWRs) based on natural uranium has reached a state of maturity. In view of civilian nuclear safeguards agreement with NSG and IAEA, Nuclear Power Reactors in India and associated fuel manufacturing facilities at Nuclear Fuel Complex (NFC) are grouped into IAEA safeguarded and out-of-safeguarded facilities. The civilian nuclear energy generation has to be accelerated for achieving energy security for the country. NFC has pioneered manufacturing technologies of UO 2 fuel, fuel clad and structural components for the PHWRs 220, 540 and PHWR700. Nearly 20 GWe of nuclear energy generation is being planned through PHWR route. Several technological improvements that were carried out recently in the production lines are the key to achieve higher productivity and safety. NFC has also been pursuing capacity augmentation by adding newer equipment in the existing facility and setting up new plants both for uranium production as well as zirconium production. Flexible manufacturing systems consisting of automatic workstations and robots were introduced in the 19 and 37 element PHWR fuel assembly lines. Various safety measures were introduced right from design stage for improving radiological safety for workmen. State-of-art equipment were designed, developed and commissioned for reduction/elimination of fatigue-oriented operations. In addition to natural uranium oxide fuel, NFC has also successfully manufactured virgin slightly enriched uranium (SEU) fuel and reprocessed depleted uranium fuels which were irradiated in the operating PHWRs. The paper brings out NFC's role in Indian nuclear power program and its manufacturing capabilities for types of PHWR fuel, zircaloy structural

  4. The research for flexible product family manufacturing based on real options

    Directory of Open Access Journals (Sweden)

    Maozhu Jin

    2015-01-01

    Full Text Available Purpose: The goal of this paper is to find the best production strategy for product mix, which means the largest value of the options. And finally, give a case and find the solution of the optimal production strategy for product mix. Design/methodology/approach: This article, based on the production with characteristics of a call option and 0-1 integer programming model, build new-products mix strategy, and through case demonstrate that traditional method underestimates the value of the products mix. Finding: According to market being volatility and uncertainty and the production can being delayed, firms can flexibly arrange the best time for products to manufacture. Use real options theory to analyze product decision and the best production timing decision. Find the total options value is higher than the traditional methods. Research limitations/implications: We are not applied to real option pricing theory in modular flexible production system. We just applied real option pricing theory to the product platform. The basic model needs to improve. While the thinking of this paper provides some research ideas for flexible production systems based on real option in further research. Practical Implications: The introduction of the real option make the company can achieve dynamic planning and flexible management for production of products mix and get the better benefit. Originality/value: The central contribution of this paper is to introduce the option mechanism in the production timing for the product mix.

  5. Social manufacturing

    OpenAIRE

    Hamalainen, Markko; Karjalainen, Jesse

    2017-01-01

    New business models harnessing the power of individuals have already revolutionized service industries and digital content production. In this study, we investigate whether a similar phenomenon is taking place in manufacturing industries. We start by conceptually defining two distinct forms of firm-individual collaboration in manufacturing industries: (1) social cloud manufacturing, in which firms outsource manufacturing to individuals, and (2) social platform manufacturing, in which firms pr...

  6. Space system production cost benefits from contemporary philosophies in management and manufacturing

    Science.gov (United States)

    Rosmait, Russell L.

    1991-01-01

    The cost of manufacturing space system hardware has always been expensive. The Engineering Cost Group of the Program Planning office at Marshall is attempting to account for cost savings that result from new technologies in manufacturing and management. The objective is to identify and define contemporary philosophies in manufacturing and management. The seven broad categories that make up the areas where technological advances can assist in reducing space system costs are illustrated. Included within these broad categories is a list of the processes or techniques that specifically provide the cost savings within todays design, test, production and operations environments. The processes and techniques listed achieve savings in the following manner: increased productivity; reduced down time; reduced scrap; reduced rework; reduced man hours; and reduced material costs. In addition, it should be noted that cost savings from production and processing improvements effect 20 to 40 pct. of production costs whereas savings from management improvements effects 60 to 80 of production cost. This is important because most efforts in reducing costs are spent trying to reduce cost in the production.

  7. Free Trade Agreements and Firm-Product Markups in Chilean Manufacturing

    DEFF Research Database (Denmark)

    Lamorgese, A.R.; Linarello, A.; Warzynski, Frederic Michel Patrick

    In this paper, we use detailed information about firms' product portfolio to study how trade liberalization affects prices, markups and productivity. We document these effects using firm product level data in Chilean manufacturing following two major trade agreements with the EU and the US....... The dataset provides information about the value and quantity of each good produced by the firm, as well as the amount of exports. One additional and unique characteristic of our dataset is that it provides a firm-product level measure of the unit average cost. We use this information to compute a firm...

  8. Design for manufacturing and assembly key performance indicators to support high-speed product development

    DEFF Research Database (Denmark)

    Thompson, Mary Kathryn; Juel Jespersen, Ida Kirstine; Kjærgaard, Thomas

    2018-01-01

    Design for Manufacturing and Assembly (DfMA) has great potential for minimizing late engineering changes (ECs) that impede high-speed product development and delay time-to-profit. However, our understanding of DfMA and its implementation in industry is still incomplete. This paper presents...... an industrial case study on late ECs in high-speed product development and compares the results to other examples from the literature. It then proposes a framework with sets of key performance indicators (KPIs) to measure and improve producability and product quality throughout the product development process....

  9. Biological effects induced by low amounts of nuclear fission products

    International Nuclear Information System (INIS)

    Vasilenko, I.Ya.; Shishkin, V.F.; Khudyakova, N.V.

    1991-01-01

    The review deals with the problem of biological hazard of low radiation doses for animals and human beings taking into the danger of internal and external irradiation by nuclear fission products under conditions of enhancing anthropogenic radiation contamination of biosphere. An attention is paid to the estimation of life span carcinogenesis, genetic and delayed effects. A conclusion is made on a necessity of multiaspect investigation of biological importance of low radiation doses taking into account modifying effects of other environmental factors

  10. A case study on Simulation and Design optimization to improve Productivity in cooling tower manufacturing industry

    Science.gov (United States)

    Pranav Nithin, R.; Gopikrishnan, S.; Sumesh, A.

    2018-02-01

    Cooling towers are the heat transfer devices commonly found in industries which are used to extract the high temperature from the coolants and make it reusable in various plants. Basically, the cooling towers has Fills made of PVC sheets stacked together to increase the surface area exposure of the cooling liquid flowing through it. This paper focuses on the study in such a manufacturing plant where fills are being manufactured. The productivity using the current manufacturing method was only 6 to 8 fills per day, where the ideal capacity was of 14 fills per day. In this plant manual labor was employed in the manufacturing process. A change in the process modification designed and implemented will help the industry to increase the productivity to 14. In this paper, initially the simulation study was done using ARENA the simulation package and later the new design was done using CAD Package and validated using Ansys Mechanical APDL. It’s found that, by the implementation of the safe design the productivity can be increased to 196 Units.

  11. Ceria-thoria pellet manufacturing in preparation for plutonia-thoria LWR fuel production

    Energy Technology Data Exchange (ETDEWEB)

    Drera, Saleem S., E-mail: saleem.drera@scatec.no [Thor Energy AS, Karenslyst allé 9C, 0278 Oslo (Norway); Björk, Klara Insulander [Thor Energy AS, Karenslyst allé 9C, 0278 Oslo (Norway); Sobieska, Matylda [Institute for Energy Technology (IFE), Nuclear Materials, Os allé 5, NO-1777, Halden (Norway)

    2016-10-15

    Thorium dioxide (thoria) has potential to assist in niche roles as fuel for light water reactors (LWRs). One such application for thoria is its use as the fertile component to burn plutonium in a mixed oxide fuel (MOX). Thor Energy and an international consortium are currently irradiating plutonia-thoria (Th-MOX) fuel in an effort to produce data for its licensing basis. During fuel-manufacturing research and development (R&D), surrogate materials were utilized to highlight procedures and build experience. Cerium dioxide (ceria) provides a good surrogate platform to replicate the chemical nature of plutonium dioxide. The project’s fuel manufacturing R&D focused on powder metallurgical techniques to ensure manufacturability with the current commercial MOX fuel production infrastructure. The following paper highlights basics of the ceria-thoria fuel production including powder milling, pellet pressing and pellet sintering. Green pellets and sintered pellets were manufactured with average densities of 67.0% and 95.5% that of theoretical density respectively. - Highlights: • High quality Ce−Th fuel production can be accomplished by utilizing powder metallurgical procedures. • Powder morphology is key to obtaining high density fuels. • Optimal pellet pressing is obtained when 3.5–4 tons of force is applied by the pellet press for powder compaction. • Pellet sintering is accomplished effectively in an Air oxidizing atmosphere. • Based on this surrogate work, expected (Th,Pu)O{sub 2} fuel density is 95.5% of theoretical density.

  12. Method for matching customer and manufacturer positions for metal product parameters standardization

    Science.gov (United States)

    Polyakova, Marina; Rubin, Gennadij; Danilova, Yulija

    2018-04-01

    Decision making is the main stage of regulation the relations between customer and manufacturer during the design the demands of norms in standards. It is necessary to match the positions of the negotiating sides in order to gain the consensus. In order to take into consideration the differences of customer and manufacturer estimation of the object under standardization process it is obvious to use special methods of analysis. It is proposed to establish relationships between product properties and its functions using functional-target analysis. The special feature of this type of functional analysis is the consideration of the research object functions and properties. It is shown on the example of hexagonal head crew the possibility to establish links between its functions and properties. Such approach allows obtaining a quantitative assessment of the closeness the positions of customer and manufacturer at decision making during the standard norms establishment.

  13. Qualification of academic facilities for small-scale automated manufacture of autologous cell-based products.

    Science.gov (United States)

    Hourd, Paul; Chandra, Amit; Alvey, David; Ginty, Patrick; McCall, Mark; Ratcliffe, Elizabeth; Rayment, Erin; Williams, David J

    2014-01-01

    Academic centers, hospitals and small companies, as typical development settings for UK regenerative medicine assets, are significant contributors to the development of autologous cell-based therapies. Often lacking the appropriate funding, quality assurance heritage or specialist regulatory expertise, qualifying aseptic cell processing facilities for GMP compliance is a significant challenge. The qualification of a new Cell Therapy Manufacturing Facility with automated processing capability, the first of its kind in a UK academic setting, provides a unique demonstrator for the qualification of small-scale, automated facilities for GMP-compliant manufacture of autologous cell-based products in these settings. This paper shares our experiences in qualifying the Cell Therapy Manufacturing Facility, focusing on our approach to streamlining the qualification effort, the challenges, project delays and inefficiencies we encountered, and the subsequent lessons learned.

  14. HOW DO DIFFERENT COORDINATION MECHANISMS BETWEEN NEW PRODUCT DEVELOPMENT AND MANUFACTURING INFLUENCE FIRM PERFORMANCE?

    DEFF Research Database (Denmark)

    Timenes Laugen, Bjørge; Acur, Nuran; Boer, Harry

    In the literature several suggestions have been put forward for tools, methods and mechanisms to coordinate new product development (NPD) and manufacturing. However, evidence of the operational performance effects of many of these approaches is at best limited. Furthermore, there is a lack...... of understanding of how various coordination mechanisms work in different contexts. Using a survey consisting of data from 677 manufacturing firms from 19 countries worldwide, we test how coordination mechanisms relate to operational performance, and how context moderates these relationships or affects performance...... between standardization and organization design, respectively, and performance are positively moderated by company size. Furthermore, innovativeness moderates the relationship between organization design and performance positively. For managers, our findings indicate that NPD-manufacturing coordination...

  15. MILK KEFIR: COMPOSITION, MICROBIAL CULTURES, BIOLOGICAL ACTIVITIES AND RELATED PRODUCTS

    Directory of Open Access Journals (Sweden)

    Maria Rosa Prado

    2015-10-01

    Full Text Available In recent years, there has been a strong focus on beneficial foods with probiotic microorganisms and functional organic substances. In this context, there is an increasing interest in the commercial use of kefir, since it can be marketed as a natural beverage that has health promoting bacteria. There are numerous commercially available kefir based-products. Kefir may act as a matrix in the effective delivery of probiotic microorganisms in different types of products. Also, the presence of kefir’s exopolysaccharides, known as kefiran, which has biological activity, certainly adds value to products. Kefiran can also be used separately in other food products and as a coating film for various food and pharmaceutical products. This article aims to update the information about kefir and its microbiological composition, biological activity of the kefir’s microflora and the importance of kefiran as a beneficial health substance.

  16. Milk kefir: composition, microbial cultures, biological activities, and related products.

    Science.gov (United States)

    Prado, Maria R; Blandón, Lina Marcela; Vandenberghe, Luciana P S; Rodrigues, Cristine; Castro, Guillermo R; Thomaz-Soccol, Vanete; Soccol, Carlos R

    2015-01-01

    In recent years, there has been a strong focus on beneficial foods with probiotic microorganisms and functional organic substances. In this context, there is an increasing interest in the commercial use of kefir, since it can be marketed as a natural beverage that has health promoting bacteria. There are numerous commercially available kefir based-products. Kefir may act as a matrix in the effective delivery of probiotic microorganisms in different types of products. Also, the presence of kefir's exopolysaccharides, known as kefiran, which has biological activity, certainly adds value to products. Kefiran can also be used separately in other food products and as a coating film for various food and pharmaceutical products. This article aims to update the information about kefir and its microbiological composition, biological activity of the kefir's microflora and the importance of kefiran as a beneficial health substance.

  17. Ionizing radiation for sterilization of medical products and biological tissues

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, S K; Raghevendrarao, M K [Bhabha Atomic Research Centre, Bombay (India). Library and Technical Information Section

    1975-10-01

    The article reviews the deliberations of the International Symposium on Ionizing Radiation for Sterilization of Medical Products and Biological Tissues which was held during 9-13 December 1974 under the auspices of the IAEA at the Bhabha Atomic Research Centre, Bombay. 42 papers were presented in the following broad subject areas: (1) Microbiological Control aspects of radiation sterilization, (2) Dosimetry aspects of radiation sterilization practices, (3) Effects of sterilizing radiation dose on the constituents of medical products, (4) Application of radiation sterilization of medical products of biological origin, (5) Technological aspects of radiation sterilization facilities, (6) Radiation sterilization of pharmaceutical substances, (7) Reports on current status of radiation sterilization of medical products in IAEA member states and (8) Working group discussion on the revision of the IAEA recommended code of practice for radiation sterilization of medical products.

  18. Yeast synthetic biology toolbox and applications for biofuel production.

    Science.gov (United States)

    Tsai, Ching-Sung; Kwak, Suryang; Turner, Timothy L; Jin, Yong-Su

    2015-02-01

    Yeasts are efficient biofuel producers with numerous advantages outcompeting bacterial counterparts. While most synthetic biology tools have been developed and customized for bacteria especially for Escherichia coli, yeast synthetic biological tools have been exploited for improving yeast to produce fuels and chemicals from renewable biomass. Here we review the current status of synthetic biological tools and their applications for biofuel production, focusing on the model strain Saccharomyces cerevisiae We describe assembly techniques that have been developed for constructing genes, pathways, and genomes in yeast. Moreover, we discuss synthetic parts for allowing precise control of gene expression at both transcriptional and translational levels. Applications of these synthetic biological approaches have led to identification of effective gene targets that are responsible for desirable traits, such as cellulosic sugar utilization, advanced biofuel production, and enhanced tolerance against toxic products for biofuel production from renewable biomass. Although an array of synthetic biology tools and devices are available, we observed some gaps existing in tool development to achieve industrial utilization. Looking forward, future tool development should focus on industrial cultivation conditions utilizing industrial strains. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permission@oup.com.

  19. Quality changes in krill and krill products during their manufacturing process

    DEFF Research Database (Denmark)

    Lu, Henna Fung Sieng; Jacobsen, Charlotte; Bruheim, Inge

    The main objective of this study is to a) investigate the effect of temperature towards the non-enzymatic browning reactions and lipid oxidation in krill products sampled at different stages during their manufacturing process. In order to further investigate this, a simple model system comprising...... amino acids (leucine, isoleucine, valine, methionine and lysine) was prepared with addition of lipid (saturated and α, β-unsaturated aldehydes) or non-enzymatic (Strecker aldehydes and pyrazine) derived volatiles. Therefore, the secondary objective is to investigate if the occurrence of non......-enzymatic browning reactions and lipid oxidation in krill products during their manufacturing process. The occurrence of these reactions could be observed in krill meal and this was ascribed to the presence of carbonyl compounds derived lipid oxidation products. The presence of a high level of non...

  20. General description and production lines of the Egyptian fuel manufacturing pilot plant

    International Nuclear Information System (INIS)

    Zidan, W.I.; Elseaidy, I.M.

    1999-01-01

    The Egyptian Fuel Manufacturing Pilot Plant, FMPP, is a new facility, producing an MTR-type fuel elements required for the Egyptian Second Research Reactor, ETRR-2, as well as other plates or elements for an external clients with the same type and enrichment percent or lower, (LEU). General description is presented. The production lines in FMPP, which begin from uranium hexaflouride (UF 6 , 19.7±0.2 % U 235 by wt), aluminum powder, and nuclear grade 6061 aluminium alloy in sheets, bars, and rods with the different heat treatments and dimensions as a raw materials, are processed through a series of the manufacturing, inspection, and quality control plan to produce the final specified MTR-type fuel elements. All these processes and the product control in each step are presented. The specifications of the final product are presented. (author)

  1. THE FACTORS AFFECTING ON THE SUCCESS OF IMPLEMENTING TOTAL PRODUCTIVE MAINTENANCE IN THE MANUFACTURING COMPANY (NS BLUESCOPE VIETNAM)

    OpenAIRE

    Pham Van Tai (PhD)*, Dean of International Trade, College of Foreign Economic Relations Phan Cao Huy (MBA), Technical Manager, Bosch Vietnam

    2017-01-01

    The competition in business environment becomes more strictly, manufacturers must introduce lots of new products on the high quality level with suitable price. Thus, new technologies have been applied, manufacturing systems become more complex. Therefore, a new strategy for maintenance such as Total productive maintenance (TPM) becomes really necessary. Many organizations have implemented TPM to increase the effectiveness of manufacturing system. However, implementation of TPM still meets a l...

  2. Production And Some Properties Of Curd A Yoghurt-Like Product Manufactured By Potato Juice And Milk

    Directory of Open Access Journals (Sweden)

    O. Aygun

    2017-07-01

    Full Text Available In this study a type of curd a yoghurt-like product YLP was prepared by potato juice and milk and some of its physico-chemical microbiological and sensory properties were examined. Analyses were applied to four yoghurt groups consisting of YLPs manufactured by using milk and potato juice at different ratios 0.5 for YLP1 1 for YLP2 and 1.5 for YLP3 and yoghurt produced using starter culture control group. Lactobacillus spp. and Lactococcus spp. numbers in all yoghurt samples manufactured by potato juice showed increase after the seventh day. The YLP manufactured by potato juice at a ratio of 0.5 was most preferred by panelists among the other YLP samples and most similar to yoghurt with starter culture.

  3. Natural product synthesis at the interface of chemistry and biology

    Science.gov (United States)

    2014-01-01

    Nature has evolved to produce unique and diverse natural products that possess high target affinity and specificity. Natural products have been the richest sources for novel modulators of biomolecular function. Since the chemical synthesis of urea by Wöhler, organic chemists have been intrigued by natural products, leading to the evolution of the field of natural product synthesis over the past two centuries. Natural product synthesis has enabled natural products to play an essential role in drug discovery and chemical biology. With the introduction of novel, innovative concepts and strategies for synthetic efficiency, natural product synthesis in the 21st century is well poised to address the challenges and complexities faced by natural product chemistry and will remain essential to progress in biomedical sciences. PMID:25043880

  4. Evaluating the Total Factor Productivity Growth in Manufacturing Industries of Iran (Data Envelopment Analysis Approach

    Directory of Open Access Journals (Sweden)

    Vahideh Ahmadi

    2014-01-01

    Full Text Available This paper examines the total factor productivity changes for 23 main manufacturing industries (2-digit ISIC group and country's provinces using data envelopment analysis during 2005 to 2007. The results show 2.3% increase in the productivity of the whole sector (average over the studied period, while the productivity of the country's provinces decreases by 7.3%, in the same period. We find Food and Beverage products and Khuzestan province having the highest productivity growth. Non-optimal allocation of resources and using of old equipments are the most important drawbacks of productivity growth for 23 main ISIC groups and provinces. Finally estimation of the regression models by panel data method reveals the privatization and increasing of labor’s available capital having a significant effect on productivity growth.

  5. 29 CFR 570.64 - Occupations involved in the manufacture of brick, tile, and kindred products (Order 13).

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Occupations involved in the manufacture of brick, tile, and... Detrimental to Their Health or Well-Being § 570.64 Occupations involved in the manufacture of brick, tile, and... term clay construction products shall mean the following clay products: Brick, hollow structural tile...

  6. GMP-conformant on-site manufacturing of a CD133+ stem cell product for cardiovascular regeneration.

    Science.gov (United States)

    Skorska, Anna; Müller, Paula; Gaebel, Ralf; Große, Jana; Lemcke, Heiko; Lux, Cornelia A; Bastian, Manuela; Hausburg, Frauke; Zarniko, Nicole; Bubritzki, Sandra; Ruch, Ulrike; Tiedemann, Gudrun; David, Robert; Steinhoff, Gustav

    2017-02-10

    CD133 + stem cells represent a promising subpopulation for innovative cell-based therapies in cardiovascular regeneration. Several clinical trials have shown remarkable beneficial effects following their intramyocardial transplantation. Yet, the purification of CD133 + stem cells is typically performed in centralized clean room facilities using semi-automatic manufacturing processes based on magnetic cell sorting (MACS®). However, this requires time-consuming and cost-intensive logistics. CD133 + stem cells were purified from patient-derived sternal bone marrow using the recently developed automatic CliniMACS Prodigy® BM-133 System (Prodigy). The entire manufacturing process, as well as the subsequent quality control of the final cell product (CP), were realized on-site and in compliance with EU guidelines for Good Manufacturing Practice. The biological activity of automatically isolated CD133 + cells was evaluated and compared to manually isolated CD133 + cells via functional assays as well as immunofluorescence microscopy. In addition, the regenerative potential of purified stem cells was assessed 3 weeks after transplantation in immunodeficient mice which had been subjected to experimental myocardial infarction. We established for the first time an on-site manufacturing procedure for stem CPs intended for the treatment of ischemic heart diseases using an automatized system. On average, 0.88 × 10 6 viable CD133 + cells with a mean log 10 depletion of 3.23 ± 0.19 of non-target cells were isolated. Furthermore, we demonstrated that these automatically isolated cells bear proliferation and differentiation capacities comparable to manually isolated cells in vitro. Moreover, the automatically generated CP shows equal cardiac regeneration potential in vivo. Our results indicate that the Prodigy is a powerful system for automatic manufacturing of a CD133 + CP within few hours. Compared to conventional manufacturing processes, future clinical application of

  7. CIM [computer-integrated manufacturing]: It all starts with product definition

    International Nuclear Information System (INIS)

    Stephens, A.E.

    1986-01-01

    The logical starting place for computer-integrated manufacturing (CIM) is at the front end of the production process - product definition. It consists of the part/assembly drawings, material lists, specifications, and procedures. Product definition starts at the design agencies: two nuclear design laboratories (Los Alamos National Laboratory and Lawrence Livermore National Laboratory) and a non-nuclear design laboratory (Sandia National Laboratories with two site locations). These laboratories perform the basic part design which is then transferred over a secure communications network to the Oak Ridge Y-12 Plant, where weapon components are produced by Martin Marietta Energy Systems, Inc., under contract with the Department of Energy (DOE). Initial Graphics Exchange Specifications (IGES) and DOE Data Exchange Format (DOEDEF) translation software is used to transfer part designs between dissimilar graphics systems. Product-definition data flow is examined both external and internal to the Y-12 Plant. Software developed specifically to computerize product definition is covered as follows: Electronic File Manager (EFM), Manage Design Documents, Distribute Product Definition, Manage Manufacturing Procedures and Product Specifications. Trident II is the first program to beneficially use CIM technologies plant-wide. Prototype software was written to add a layer of user friendliness through multilayer menu selects to enable access to a number of existing application software packages. Additional software was developed and purchased that enables a single personal computer to meet many needs. These product-definition needs include procedures generation, graphics viewing, and office automation. 3 figs

  8. The Impact of Organizational Learning Capability on Product Innovation Performance: Evidence from the Turkish Manufacturing Sector

    Directory of Open Access Journals (Sweden)

    Özlem Yaşar Uğurlu

    2016-02-01

    Full Text Available This study aims to examine the effect of organizational learning capability on product innovation performance in the manufacturing sector using empirical data. A survey was conducted with 120 firms that were on the list of Top 1000 Firms of Turkey and registered with the Istanbul Chamber of Industry, to examine the relationship between the dimensions of organizational learning capability and the dimensions of product innovation performance. The findings of the study indicate a positive relationship between organizational learning capability and product innovation performance.

  9. Linking culture, organizational, learning orientation and product innovation performance: the case of Ethiopian manufacturing firms

    Directory of Open Access Journals (Sweden)

    Beyene, K. T.

    2016-05-01

    Full Text Available Using formal survey data from textile and leather product manufacturing firms in Ethiopia, we investigate how the current national cultural setup (power distance, collectivism, masculinity and uncertainty avoidance is affecting organizational learning, orientation and product innovation performance. Further, we assess the moderating role of sector and ownership structure on the interrelationship. The result demonstrates that the current national culture setup is negatively affecting the learning and innovation activities of the firms in the country. It also shows that while sector type is neutral, ownership type significantly affects the interrelationship among culture, learning orientation and product innovation performance.

  10. Synthetic and systems biology for microbial production of commodity chemicals.

    Science.gov (United States)

    Chubukov, Victor; Mukhopadhyay, Aindrila; Petzold, Christopher J; Keasling, Jay D; Martín, Héctor García

    2016-01-01

    The combination of synthetic and systems biology is a powerful framework to study fundamental questions in biology and produce chemicals of immediate practical application such as biofuels, polymers, or therapeutics. However, we cannot yet engineer biological systems as easily and precisely as we engineer physical systems. In this review, we describe the path from the choice of target molecule to scaling production up to commercial volumes. We present and explain some of the current challenges and gaps in our knowledge that must be overcome in order to bring our bioengineering capabilities to the level of other engineering disciplines. Challenges start at molecule selection, where a difficult balance between economic potential and biological feasibility must be struck. Pathway design and construction have recently been revolutionized by next-generation sequencing and exponentially improving DNA synthesis capabilities. Although pathway optimization can be significantly aided by enzyme expression characterization through proteomics, choosing optimal relative protein expression levels for maximum production is still the subject of heuristic, non-systematic approaches. Toxic metabolic intermediates and proteins can significantly affect production, and dynamic pathway regulation emerges as a powerful but yet immature tool to prevent it. Host engineering arises as a much needed complement to pathway engineering for high bioproduct yields; and systems biology approaches such as stoichiometric modeling or growth coupling strategies are required. A final, and often underestimated, challenge is the successful scale up of processes to commercial volumes. Sustained efforts in improving reproducibility and predictability are needed for further development of bioengineering.

  11. Biological hydrogen production by moderately thermophilic anaerobic bacteria

    International Nuclear Information System (INIS)

    HP Goorissen; AJM Stams

    2006-01-01

    This study focuses on the biological production of hydrogen at moderate temperatures (65-75 C) by anaerobic bacteria. A survey was made to select the best (moderate) thermophiles for hydrogen production from cellulolytic biomass. From this survey we selected Caldicellulosiruptor saccharolyticus (a gram-positive bacterium) and Thermotoga elfii (a gram-negative bacterium) as potential candidates for biological hydrogen production on mixtures of C 5 -C 6 sugars. Xylose and glucose were used as model substrates to describe growth and hydrogen production from hydrolyzed biomass. Mixed substrate utilization in batch cultures revealed differences in the sequence of substrate consumption and in catabolites repression of the two microorganisms. The regulatory mechanisms of catabolites repression in these microorganisms are not known yet. (authors)

  12. An Agent-based Manufacturing Management System for Production and Logistics within Cross-Company Regional and National Production Networks

    Directory of Open Access Journals (Sweden)

    T. Hanel

    2008-11-01

    Full Text Available The goal is the development of a simultaneous, dynamic, technological as well as logistical real-time planning and an organizational control of the production by the production units themselves, working in the production network under the use of Multi-Agent-Technology. The design of the multi-agent-based manufacturing management system, the models of the single agents, algorithms for the agent-based, decentralized dispatching of orders, strategies and data management concepts as well as their integration into the SCM, basing on the solution described, will be explained in the following.

  13. An Agent-Based Manufacturing Management System for Production and Logistics within Cross-Company Regional and National Production Networks

    Directory of Open Access Journals (Sweden)

    S. Heinrich

    2005-03-01

    Full Text Available The goal is the development of a simultaneous, dynamic, technological as well as logistical real-time planning and an organizational control of the production by the production units themselves, working in the production network under the use of Multi-Agent-Technology. The design of the multi-agent-based manufacturing management system, the models of the single agents, algorithms for the agent-based, decentralized dispatching of orders, strategies and data management concepts as well as their integration into the SCM, basing on the solution described, will be explained in the following.

  14. Produtividade fabril I: método para rápido aumento da produtividade fabril Manufacture productivity I: quick improvement method of the manufacture productivity

    Directory of Open Access Journals (Sweden)

    José Celso Contador

    1994-12-01

    Full Text Available O método para rápido aumento da produtividade fabril, aplicável principalmente à indústria brasileira de manufatura (17% do PIB, fundamenta-se exclusivamente na redução ou eliminação do tempo inativo do homem, da máquina e do material, que é a grande causa da ineficiência. O método exige a utilização de apenas cinco das mais simples, elementares e conhecidas técnicas e é aplicável às vinte situações mais freqüentes (objetos de estudo na indústria de manufatura. Nossa experiência atesta que o método é capaz de aumentar a produtividade fabril em valor superior a 30%, em poucos meses e de forma perene (houve um caso de aumento de 160% em toda uma seção de usinagem de uma empresa multinacional. Sua aplicação e a implantação das medidas dele decorrentes são feitas com extrema facilidade e, por isto, os resultados surgem muito rapidamente. Atinge portanto seu objetivo: proporcionar aumento da produtividade fabril em curto espaço de tempo. Os demais artigos da série detalharão os objetos de estudo.The quick improvement method of the manufacture productivity is based on the reduction or on the elimination of the machine/operator/material inative time, exclusively. The inative time of this three elements is recognized to be main reason of the inefficiency. The method here discussed is specially applicable in the brazilian manufacturing industry (which represents 17% of the PIB. It utilizes five of the most simple, elementary and well-known thechniques and it is applicable in the most frequent situations of the manufacturing industries. The background of the author assures that the method can to improve the productivity beyond 30% in a short time (in a particular enterprise, it was possible to improve 160% the productivity of its machining department. The application of the method and the implementation of its suggested rules are made with right facility and, because that, the results appear very quickly. A succession

  15. Practical application of game theory based production flow planning method in virtual manufacturing networks

    Science.gov (United States)

    Olender, M.; Krenczyk, D.

    2016-08-01

    Modern enterprises have to react quickly to dynamic changes in the market, due to changing customer requirements and expectations. One of the key area of production management, that must continuously evolve by searching for new methods and tools for increasing the efficiency of manufacturing systems is the area of production flow planning and control. These aspects are closely connected with the ability to implement the concept of Virtual Enterprises (VE) and Virtual Manufacturing Network (VMN) in which integrated infrastructure of flexible resources are created. In the proposed approach, the players role perform the objects associated with the objective functions, allowing to solve the multiobjective production flow planning problems based on the game theory, which is based on the theory of the strategic situation. For defined production system and production order models ways of solving the problem of production route planning in VMN on computational examples for different variants of production flow is presented. Possible decision strategy to use together with an analysis of calculation results is shown.

  16. Technical suitability mapping of feedstocks for biological hydrogen production

    NARCIS (Netherlands)

    Panagiotopoulos, I.A.; Karaoglanoglou, L.S.; Koullas, D.P.; Bakker, R.R.; Claassen, P.A.M.; Koukios, E.G.

    2015-01-01

    The objective of this work was to map and compare the technical suitability of different raw materials for biological hydrogen production. Our model was based on hydrogen yield potential, sugar mobilization efficiency, fermentability and coproduct yield and value. The suitability of the studied

  17. Production of biological nanoparticles from bovine serum albumin ...

    African Journals Online (AJOL)

    Production of biological nanoparticles from bovine serum albumin for drug delivery. ... Bovine serum albumin (BSA) was used for generation of nanoparticles in a drug delivery system. ... The impact of protein concentration and additional rate of organic solvent (i.e. ethanol) upon the particle ... AJOL African Journals Online.

  18. Method of manufacturing gadolinium oxide-incorporated nuclear fuel sintering products

    International Nuclear Information System (INIS)

    Komono, Akira; Seki, Makoto; Omori, Sadayuki.

    1987-01-01

    Purpose: To manufacture nuclear fuel sintering products excellent in burning property and mechanical property. Constitution: In the manufacturing step for nuclear fuel sintering products, specific metal oxides are added for promoting the growth of crystal grains in the sintering. Those metal oxides melted at a temperature lower than the sintering temperature of a mixture of nuclear fuel oxide powder and oxide power, or those metal oxides causing eutectic reaction are used as the metal oxide. Particularly, those compounds having oxygen atom - metal atom ratio (O/M) of not less than 2 are preferably used. As such metal oxides usable herein transition metal oxides, e.g., Nb 2 O 5 , TiO 2 , MoO 3 and WO 3 are preferred, with Nb 2 O 3 and TiO 2 being preferred particularly. (Seki, T.)

  19. Total Factor Productivity and Energy Intensity in Indian Manufacturing: A Cross-Sectional Study

    Directory of Open Access Journals (Sweden)

    Santosh Kumar Sahu

    2011-01-01

    Full Text Available The objective of the paper is to estimate the transcendental logarithmic production function and further study the determinants of total factor productivity (TFP of Indian manufacturing industries. The estimation of TFP is based on four inputs model, where apart from labour and capital, material and energy are the other two inputs. The findings of the paper suggest that labour and material inputs play major role as compared to the capital and energy input. Age of the firm, ownership, energy intensity, embodied and disembodied technology imports, research and development and exports were considered as the possible determinants of the TFP in the second stage regression. The finding of the estimates suggest that age of the firm, export intensity and disembodied technology import are positively related to the TFP, where ownership, energy intensity, embodied technology import and R&D intensity are negatively related to the TFP of the firms for Indian manufacturing.

  20. 21 CFR 610.50 - Date of manufacture.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Date of manufacture. 610.50 Section 610.50 Food... GENERAL BIOLOGICAL PRODUCTS STANDARDS Dating Period Limitations § 610.50 Date of manufacture. The date of manufacture shall be determined as follows: (a) For products for which an official standard of potency is...

  1. Implementation of Lean System on Erbium Doped Fibre Amplifier Manufacturing Process to Reduce Production Time

    Science.gov (United States)

    Maneechote, T.; Luangpaiboon, P.

    2010-10-01

    A manufacturing process of erbium doped fibre amplifiers is complicated. It needs to meet the customers' requirements under a present economic status that products need to be shipped to customers as soon as possible after purchasing orders. This research aims to study and improve processes and production lines of erbium doped fibre amplifiers using lean manufacturing systems via an application of computer simulation. Three scenarios of lean tooled box systems are selected via the expert system. Firstly, the production schedule based on shipment date is combined with a first in first out control system. The second scenario focuses on a designed flow process plant layout. Finally, the previous flow process plant layout combines with production schedule based on shipment date including the first in first out control systems. The computer simulation with the limited data via an expected value is used to observe the performance of all scenarios. The most preferable resulted lean tooled box systems from a computer simulation are selected to implement in the real process of a production of erbium doped fibre amplifiers. A comparison is carried out to determine the actual performance measures via an analysis of variance of the response or the production time per unit achieved in each scenario. The goodness of an adequacy of the linear statistical model via experimental errors or residuals is also performed to check the normality, constant variance and independence of the residuals. The results show that a hybrid scenario of lean manufacturing system with the first in first out control and flow process plant lay out statistically leads to better performance in terms of the mean and variance of production times.

  2. Monitoring of clobetasol propionate and betamethasone dipropionate as undeclared steroids in cosmetic products manufactured in Korea.

    Science.gov (United States)

    Nam, Yun Sik; Kwon, Il Keun; Lee, Kang-Bong

    2011-07-15

    Some cosmetic products manufactured in Korea have been suspected to contain anti-inflammatory corticosteroids, such as clobetasol propionate and betamethasone dipropionate, for the treatment of eczema, seborrhea and psoriasis, without any indication on the label of the cosmetic products. Due to their severe side effects, such as permanent skin atopy, these two corticosteroids in cosmetic products need to be monitored from a forensic point of view. Cosmetic product samples (number of samples=47) of manufacturers charged by consumers have been collected in local and online markets of Korea, and they were validated and analyzed by a simple high performance liquid chromatography (HPLC) method with ultraviolet diode array (UV-DAD). LC-MS/MS and LC-MS were used to confirm these steroids in cosmetic samples with diagnostic ions (m/z) and isotope ratio. Linearity was studied with 0.5-10μg/mL range in both steroids. Good correlation coefficients (r(2)≥0.999) were found, and their limits of quantifications were 0.59μg/mL and 0.66μg/mL in clobetasol propionate and betamethasone dipropionate, respectively. At three different concentrations spanning the linear dynamic ranges, mean recoveries were always higher than 93%, and precisions for intra-day and inter-day analyses were both less than 3.5%. The results show 32-96.4μg/g levels of clobetasol propionate in five different cosmetic products. Also, betamethasone dipropionate in a sample was monitored at the level of 195.1μg/g. This fact reveals that some manufacturers have added these steroids in their cosmetic products to advertise the treatment effect for skin atopy. Thus, these cosmetic products need to be monitored carefully, and ultimately removed from the market. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

  3. Environmental Regulation and Competitiveness: Evidence from Trade and Production in the Manufacturing Sector

    OpenAIRE

    Yang, Tsung Yu

    2014-01-01

    Previous empirical studies of the pollution haven hypothesis (PHH) have not reached a consistent conclusion. The existing literature is primarily based on anecdotes and scattered case studies. This study analyzes the trade flows and composition change of the most polluting industries in manufacturing sectors among countries in order to offer a more general conclusion. This study finds that stricter environmental regulation stringency decreases the net export and production share of the most p...

  4. Photovoltaics manufacturer's overview of interactions with customers of photovoltaic products

    Energy Technology Data Exchange (ETDEWEB)

    Darkazalli, G.

    1982-11-01

    Communications between the customer and manufacturer of photovoltaic products often require time-consuming interaction before each has the necessary information. Customers appear not to know what information is needed by the supplier to size photovoltaic systems properly nor are they adequately able to estimate their own system needs. Customers can make unrealistic measurement demands and do not provide feedback to the supplier on system performance in the field.

  5. Benchmarking Naval Shipbuilding with 3D Laser Scanning, Additive Manufacturing, and Collaborative Product Lifecycle Management

    Science.gov (United States)

    2015-09-20

    are also available. These technologies are past the disillusionment stage and are in the enlightenment phase where benefits are being derived, as... technologies such as three-dimensional scanning (3DLS), product lifecycle management (PLM), and additive manufacturing (AM) to reduce costs while...naval shipbuilding savings. The research was conducted in two phases. In the first phase, secondary research was conducted on the three technologies

  6. The manufacture of MTR fuel elements and Mo99 production targets at Dounreay

    International Nuclear Information System (INIS)

    Gibson, J.

    1997-01-01

    Uranium/aluminium alloy elements have been produced at Dounreay for nearly 40 years. In April 1990 the two DIDO-type reactors operated by the United Kingdom Atomic Energy Authority (UKAEA) at Harwell were closed, with the result that a large portion of the then current customer base disappeared and, to satisfy the needs of the evolving market, the decision was taken to invest over 1m pounds in new equipment for the manufacture of dispersed fuels and molybdenum production targets. (author)

  7. Design of an automatic production monitoring system on job shop manufacturing

    Science.gov (United States)

    Prasetyo, Hoedi; Sugiarto, Yohanes; Rosyidi, Cucuk Nur

    2018-02-01

    Every production process requires monitoring system, so the desired efficiency and productivity can be monitored at any time. This system is also needed in the job shop type of manufacturing which is mainly influenced by the manufacturing lead time. Processing time is one of the factors that affect the manufacturing lead time. In a conventional company, the recording of processing time is done manually by the operator on a sheet of paper. This method is prone to errors. This paper aims to overcome this problem by creating a system which is able to record and monitor the processing time automatically. The solution is realized by utilizing electric current sensor, barcode, RFID, wireless network and windows-based application. An automatic monitoring device is attached to the production machine. It is equipped with a touch screen-LCD so that the operator can use it easily. Operator identity is recorded through RFID which is embedded in his ID card. The workpiece data are collected from the database by scanning the barcode listed on its monitoring sheet. A sensor is mounted on the machine to measure the actual machining time. The system's outputs are actual processing time and machine's capacity information. This system is connected wirelessly to a workshop planning application belongs to the firm. Test results indicated that all functions of the system can run properly. This system successfully enables supervisors, PPIC or higher level management staffs to monitor the processing time quickly with a better accuracy.

  8. Productivity improvement: Implementation and analysis of clustering technique in manufacturing of timing gearbox cover

    Directory of Open Access Journals (Sweden)

    Satbir Singh

    2016-04-01

    Full Text Available Productivity is an indicator of efficiency with which resources, both human and material, are transformed into useful services and goods. The vital purpose of the prevailing work was to analyze the factors involved in the improvement of productivity in all its types such as material, capital, labor, machine and total productivity at the plant. This was obtained by decreasing the manufacturing cost per component by reducing its cycle time and increasing the monthly production rate. The experimentation revealed that using proposed processes and improved tooling, monthly production rate has increased by 16.2% due to reduced cycle time, the number of defected components i.e. rejection rate has reduced up to 2%. A reduction of 6.78% in manufacturing cost per component was recorded. Tooling cost has reduced by more than 12%. Saving up to 50% in inspection cost has been recorded due to close dimensional tolerances and high surface finish achieved on components. An increase of 4.84% was recorded in total productivity.

  9. PERSPECTIVES FOR DEVELOPMENT OF THE BIOLOGIC PLUM PRODUCTION IN BULGARIA

    Directory of Open Access Journals (Sweden)

    Ivanka Vitanova

    2014-03-01

    Full Text Available The Bulgarian plum cultivars Gabrovska, Nevena, Strinava, Guliaeva and Balvanska slava, breeding in the Plum Experimental Station in the town of Dryanovo and the introduced cultivars Stanley, Chachanska lepotitsa, Opal, Malvazinka, Hramova renkloda, Tuleu timpuriu, Althan’s Gage, Pacific, Mirabell de Nancy, Anna Schpet and Jojo, what are high productive and are tolerant to sharka and other important economic plum diseases are suitable for the biologic plum production. The organic fertilization is a basic element of the technology for the biologic plum production. The fertilization with manure and the green manure with a winter green peas and with a peas-rye mix increased the humus content, influenced positive action on the supplying of the plum plants with the main nutrient macro elements, increased the yield and to be able apply successfully in the plum orchards and at not irrigation conditions.

  10. Optimisation of the manufacturing process of tritide and deuteride targets used for neutron production

    International Nuclear Information System (INIS)

    Monnin, Carole; Bach, Pierre; Tulle, Pierre Alain; Rompay, Marc van; Ballanger, Anne

    2002-01-01

    As a neutron tube manufacturer, SODERN is now in charge of manufacturing tritium targets for accelerators, in cooperation with CEA/DAM/DTMN in Valduc. Specific deuterium and tritium targets are manufactured on request, according to the requirements of the users, starting from titanium targets on copper substrates, and going to more sophisticated devices. The range of possible uses is wide, including thin targets for neutron calibration, thick targets with controlled loading of deuterium and tritium, rotating targets or large size rotating targets for higher lifetimes. The activity of the targets ranges from 3.7x10 10 to 3.7x10 13 Bq (1-1000 Ci), the diameter being up to 30 cm. Sodern and the CEA/Valduc centre have developed different technologies for tritium target manufacture, allowing the selection of the best configuration for each kind of use. In order to optimize the production of high energy neutrons, the performance of tritide and deuteride titanium targets made by different processes has been studied experimentally by bombardment with 120 and 350 kV deuterons provided by electrostatic accelerators. It is then possible to optimize either neutron output or lifetime and stability or thermal behaviour. The importance of the deposit evaporation conditions on the efficiency of neutron emission is clearly demonstrated, as well as the thermomechanical stability of the Ti thin film under deuteron bombardment. The main parameters involved in the target performance are discussed from a thermodynamical approach

  11. Optimisation of the manufacturing process of tritide and deuteride targets used for neutron production

    Science.gov (United States)

    Monnin, Carole; Bach, Pierre; Tulle, Pierre Alain; van Rompay, Marc; Ballanger, Anne

    2002-03-01

    As a neutron tube manufacturer, SODERN is now in charge of manufacturing tritium targets for accelerators, in cooperation with CEA/DAM/DTMN in Valduc. Specific deuterium and tritium targets are manufactured on request, according to the requirements of the users, starting from titanium targets on copper substrates, and going to more sophisticated devices. The range of possible uses is wide, including thin targets for neutron calibration, thick targets with controlled loading of deuterium and tritium, rotating targets or large size rotating targets for higher lifetimes. The activity of the targets ranges from 3.7×10 10 to 3.7×10 13 Bq (1-1000 Ci), the diameter being up to 30 cm. Sodern and the CEA/Valduc centre have developed different technologies for tritium target manufacture, allowing the selection of the best configuration for each kind of use. In order to optimize the production of high energy neutrons, the performance of tritide and deuteride titanium targets made by different processes has been studied experimentally by bombardment with 120 and 350 kV deuterons provided by electrostatic accelerators. It is then possible to optimize either neutron output or lifetime and stability or thermal behaviour. The importance of the deposit evaporation conditions on the efficiency of neutron emission is clearly demonstrated, as well as the thermomechanical stability of the Ti thin film under deuteron bombardment. The main parameters involved in the target performance are discussed from a thermodynamical approach.

  12. Spatial Agglomeration and Productivity of Textile and Leather Manufacturing in the Punjab Province of Pakistan

    Directory of Open Access Journals (Sweden)

    Asim Iqba

    2013-05-01

    Full Text Available This study investigates whether spatial agglomeration of textile and leather industry facilitates to enhance its own productivity at establishment level in the Punjab province of Pakistan. The empirical analysis is based on the survey data for the years 1995-96, 2000-2001 and 2005-06 collected from the Punjab Bureau of Statistics (PBS. The production function framework has been utilized. The results of production function suggest that spatial agglomeration of textile and leather industry plays a vital role in determining the productivity of establishments. The impact of localization (specialization is positive and stronger than urbanization (diversification which implies that locating manufacturing establishments in a particular district leads to enhance the productivity of establishments. Therefore, government policy should be biased to promote localization of textile and leather industry.

  13. Impact of product platforms on lean production systems : evidence from industrial machinery manufacturing

    NARCIS (Netherlands)

    Alblas, A.A.; Wortmann, J.C.

    2012-01-01

    The present study describes the effects of product platform changes on lean production systems. Current research into product platforms focuses mostly on the development stage. However, although the initial development of platforms is an important issue, product platforms often evolve during later

  14. Big Data Based Analysis Framework for Product Manufacturing and Maintenance Process

    OpenAIRE

    Zhang , Yingfeng; Ren , Shan

    2015-01-01

    Part 8: Cloud-Based Manufacturing; International audience; With the widely use of smart sensor devices in the product lifecycle management (PLM), it creates amount of real-time and muti-source lifecycle big data. These data allow decision makers to make better-informed PLM decisions. In this article, an overview framework of big data based analysis for product lifecycle (BDA-PL) was presented to provide a new paradigm by extending the techniques of Internet of Things (IoT) and big data analys...

  15. Characterization of additive manufacturing processes for polymer micro parts productions using direct light processing (DLP) method

    DEFF Research Database (Denmark)

    Davoudinejad, Ali; Pedersen, David Bue; Tosello, Guido

    The process capability of additive manufacturing (AM) for direct production of miniaturized polymer components with micro features is analyzed in this work. The consideration of the minimum printable feature size and obtainable tolerances of AM process is a critical step to establish a process...... chains for the production of parts with micro scale features. A specifically designed direct light processing (DLP) AM machine suitable for precision printing has been used. A test part is designed having features with different sizes and aspect ratios in order to evaluate the DLP AM machine capability...

  16. Advanced Shape Memory Technology to Reshape Product Design, Manufacturing and Recycling

    Directory of Open Access Journals (Sweden)

    Wen Guang Yang

    2014-08-01

    Full Text Available This paper provides a brief review on the advanced shape memory technology (ASMT with a focus on polymeric materials. In addition to introducing the concept and fundamentals of the ASMT, the potential applications of the ASMT either alone or integrated with an existing mature technique (such as, 3D printing, quick response (QR code, lenticular lens and phenomena (e.g., wrinkling and stress-enhanced swelling effect in product design, manufacturing, and recycling are demonstrated. It is concluded that the ASMT is indeed able to provide a range of powerful approaches to reshape part of the life cycle or the whole life cycle of products.

  17. An exploratory assessment of the attitudes of Chinese wood products manufacturers towards forest certification.

    Science.gov (United States)

    Chen, Juan; Innes, John L; Kozak, Robert A

    2011-11-01

    Interviews with Chinese forest products manufacturers were conducted to explore their attitudes towards forest certification and related issues. Participants comprised owners, CEOs, and managers in 20 Chinese wood products companies, including producers of furniture, doors, flooring, and various engineered wood products. The interviews were used to analyze the extent to which participants were considering adopting forest certification and what might motivate such a decision. This was done by assessing their awareness and knowledge of certification. The results indicated that participants' understanding of forest certification was extremely low, despite major efforts in China to raise awareness of the issue. Potential economic benefits were the most frequently cited reason to adopt certification, including gaining or maintaining competitive advantage over their industry counterparts, improved access to both domestic and export markets, better customer recognition, and enhanced corporate responsibility practices. Some interviewees (3 out of 20) considered that certification would become a mandatory requirement or industry standard, and that this would be the only viable motivation for certification given that the financial benefits were potentially limited. According to the participants, the main differences between certified and uncertified wood products operations related to improved market access and public image. Interviewees felt that cooperation between and support from governments and the forest industry would enable the enhanced awareness of certification amongst manufacturers and the general public. This, in turn, could serve to stimulate demand for certified products. Copyright © 2011 Elsevier Ltd. All rights reserved.

  18. The impact of lean manufacturing as a factor for improving productive performance

    Directory of Open Access Journals (Sweden)

    Leoni Pentiado Godoy

    2018-06-01

    Full Text Available The main objective of this article is to present the impact that the Lean manufacturing tool can have in a company that does not have management methodology for the Toyota Production System. This work was carried out in an industry that outsources services for the export of the medium-sized leather footwear producers sector located in the industrial pole of RS, Brazil. In the data collection, questions were raised with the managers and collaborators, as well as the researcher’s empirical view on the decisions that were being taken in the productive processes for a period of four months. These data were analyzed using Excel spreadsheets. In the results , the importance of the application of the Lean Manufacturing tools was highlighted , and some suggestions were given to the managers, mainly in relation to the idle capacity of production in several sectors, representing how much more the company could be producing to reach its maximum capacity. The mapping applied identified the adaptation of new machines for better production results, as well as intensifying the mapping of the critical paths that aggregate and do not add value in the productive operating environment.

  19. A Decision Optimization Model for Leased Manufacturing Equipment with Warranty under Forecasting Production/Maintenance Problem

    Directory of Open Access Journals (Sweden)

    Zied Hajej

    2015-01-01

    Full Text Available Due to the expensive production equipment, many manufacturers usually lease production equipment with a warranty period during a finite leasing horizon, rather than purchasing them. The lease contract contains the possibility of obtaining an extended warranty for a given additional cost. In this paper, based on the forecasting production/maintenance optimization problem, we develop a mathematical model to study the lease contract with basic and extended warranty based on win-win relationship between the lessee and the lessor. The influence of the production rates in the equipment degradation consequently on the total cost by each side during the finite leasing horizon is stated in order to determine a theoretical condition under which a compromise-pricing zone exists under different possibilities of maintenance policies.

  20. Practical Use of Nitrite and Basis for Dosage in the Manufacture of Meat Products

    DEFF Research Database (Denmark)

    Adler-Nissen, Jens; Ekgreen, Maria Helbo; Risum, Jørgen

    . The particularities of the production methods make such a quantification rather uncertain. Furthermore, some dry cured products from South Europe are made with nitrate, which slowly and only partly is converted to nitrite and further to NO during the curing process. The Danish limitations on the use of nitrate......The use of nitrite (NaNO2) in the manufacture of salted (cured) meat products has a long tradition in the industry, dating back to the early twentieth century. Nitrite serves several technological purposes, primarily by the formation of a stable red colour in the meat and the inhibition...... of the growth of Clostridium botulinum. According to an assessment report by the European Food Safety Authority (The EFSA Journal, 14, p. 1-134, 2003) all evidence points to that it is the added amount of nitrite rather than the residual amount of nitrite in the product which exerts the antimicrobial effect...

  1. 21 CFR 1002.51 - Exemptions for manufacturers of products intended for the U.S. Government.

    Science.gov (United States)

    2010-04-01

    ... for the U.S. Government. 1002.51 Section 1002.51 Food and Drugs FOOD AND DRUG ADMINISTRATION.... Government. Upon application therefor by the manufacturer, the Director, Center for Devices and Radiological Health, may exempt from the provisions of this part a manufacturer of any electronic product intended for...

  2. British and German manufacturing productivity compared : A new benchmark for 1935/36 based on double deflated value added

    NARCIS (Netherlands)

    Fremdling, Rainer; de Jong, Herman; Timmer, Marcel P.

    We present a new estimate of Anglo-German manufacturing productivity levels for 1935/36. It is based on archival data on German manufacturing and published British census data. We calculate comparative levels of value added, correcting for differences in prices for outputs and inputs. This so-called

  3. Users guide for WoodCite, a product cost quotation tool for wood component manufacturers [computer program

    Science.gov (United States)

    Jeff Palmer; Adrienn Andersch; Jan Wiedenbeck; Urs. Buehlmann

    2014-01-01

    WoodCite is a Microsoft® Access-based application that allows wood component manufacturers to develop product price quotations for their current and potential customers. The application was developed by the U.S. Forest Service and Virginia Polytechnic Institute and State University, in cooperation with the Wood Components Manufacturers Association.

  4. Biological risks associated with consumption of reptile products

    DEFF Research Database (Denmark)

    Magnino, S.; Colin, P.; Dei-Cas, E.

    2009-01-01

    recently increased in some areas of the world. Biological risks associated with the consumption of products from both farmed and wild reptile meat and eggs include infections caused by bacteria (Salmonella spp., Vibrio spp.). parasites (Spirometra, Trichinella, Gnathostoma, pentastomids), as well...... to increase the occurrence of biological hazards in reptile meat. Application of GHP, GMP and HACCP procedures, respectively at farm and slaughterhouse level, is crucial for controlling the hazards.......The consumption of a wide variety of species of reptiles caught from the wild has been an important source of protein for humans world-wide for millennia. Terrapins. snakes, lizards, crocodiles and iguanas are now farmed and the consumption and trade of their meat and other edible products have...

  5. Stimuli of Collaboration in Product Development: A Case Study in a Project Manufacturing Company

    Directory of Open Access Journals (Sweden)

    Jääskeläinen Aki

    2017-12-01

    Full Text Available There is already a wide acceptance on the importance of involving supplier and customer companies in product development. Decent understanding prevails on the relationship-oriented approach to product development including various collaboration forms. However, there is less research on the factors explaining the decision of attending to joint product development. In addition, less studies have examined the integrated role of both suppliers and customers in product development initiatives. This study searches answers to the following research questions: 1. What is the role of different actors in product development initiatives? 2. What factors motivate suppliers and customers to participate in product development? The research is carried out as an in-depth qualitative single case study in a large project manufacturing company. It takes the perspective of a focal company striving for product improvements. The first part of the empirical study consists of 15 semi-structured interviews. The second part includes two discursive workshops and builds upon the results of the interviews. This study contributes to the existing research by explaining the challenges and conditions facilitating joint product development with supplier and purchaser companies. The results highlight the role of customers in improving the effectiveness of product development. As a practical contribution, the paper reports the application of workshop method as a facilitator of collaboration between supplier, purchaser (focal company and customer companies.

  6. Evaluating the effect of exchange rate and labor productivity on import penetration of Brazilian manufacturing sectors

    Directory of Open Access Journals (Sweden)

    João Paulo Martin Faleiros

    2016-01-01

    Full Text Available In recent years, several economists have argued that the sharp loss of competitiveness of the Brazilian industry was caused by a strong exchange rate appreciation. However, other economists have attributed this loss of competitiveness to the dismal growth of labor productivity in the Brazilian industrial sector. The present paper proposes to estimate the differential impacts of variations in exchange rate and labor productivity on the Brazilian market share of imports measured by the coefficient of import penetration of total demand for manufacturing goods. We start by developing a simple theoretical model to investigate under what conditions the impacts of an exchange rate depreciation and an increase in labor productivity would differ. We test the theoretical implications of the model by means of a GMM panel data analysis focusing on 17 manufacturing sectors in the period between 1996 and 2011. Our results suggest that both variables matter to explain the coefficient of import penetration. Nevertheless, labor productivity has the strongest negative impact on the market share of imported goods, even after controlling for sector fixed-effects.

  7. PCMO L01-Setting Specifications for Biological Investigational Medicinal Products.

    Science.gov (United States)

    Krause, Stephan O

    2015-01-01

    This paper provides overall guidance and best practices for the setting of specifications for clinical biological drug substances and drug products within the framework of ICH guidelines on pharmaceutical development [Q8(R2) and Q11], quality risk management (Q9), and quality systems (Q10). A review is provided of the current regulatory expectations for the specification setting process as part of a control strategy during product development, pointing to existing challenges for the investigational new drug/investigational medicinal product dossier (IND/IMPD) sponsor. A case study illustrates how the investigational medicinal product specification revision process can be managed within a flexible quality system, and how specifications can be set and justified for early and late development stages. This paper provides an overview for the setting of product specifications for investigational medicinal products used in clinical trials. A case study illustrates how product specifications of investigational medicinal products can be justified and managed within a modern product quality system. © PDA, Inc. 2015.

  8. National experience in radiosterelization or radiodescontamination of biological products

    International Nuclear Information System (INIS)

    Padron, E.; Romay, Z.; Otero, I.; Chavez, A.; Prieto, E.; Sainz, D.; Rodriguez, R.; Diaz, D.

    1997-01-01

    The ionizing radiations are especially important when other chemical and physical methods can't be used, or they don't give the result required, for which the employment of advanced technologies for the sterilization is found in ascent at world level. To such effect, the International Atomic Energy Agency has, sponsored a coordinated program for the radiosterilization of medical and biological products in Latin America, in which Cuba participates. (author) [es

  9. Implementation of Plasma Fractionation in Biological Medicines Production

    OpenAIRE

    Mousavi Hosseini, Kamran; Ghasemzadeh, Mehran

    2016-01-01

    Context The major motivation for the preparation of the plasma derived biological medicine was the treatment of casualties from the Second World War. Due to the high expenses for preparation of plasma derived products, achievement of self-sufficiency in human plasma biotechnological industry is an important goal for developing countries. Evidence Acquisition The complexity of the blood plasma was first revealed by the Nobel Prize laureate, Arne Tiselius and Theodor Svedberg, which resulted in...

  10. State of the art of biological hydrogen production processes

    International Nuclear Information System (INIS)

    Loubette, N.; Junker, M.

    2006-01-01

    Our report gives an overview of hydrogen production processes with bacteria or algae. 4 main processes are described: water biophotolysis, photo- fermentation biological CO conversion and dark fermentation. Chemical phenomena which lead to hydrogen generation are exp/aired. Performances, limits and outlook are given for each process. Main projects, programs and key players involved in this field of research have been listed. This paper resumes few results of this report. (authors)

  11. State of the art of biological hydrogen production processes

    International Nuclear Information System (INIS)

    Nicolas Loubette; Michel Junker

    2006-01-01

    Our report gives an overview of hydrogen production processes with bacteria or algae. 4 main processes are described: water bio-photolysis, photo-fermentation biological CO conversion and dark fermentation. Chemical phenomena which lead to hydrogen generation are explained. Performances, limits and outlook are given for each process. Main projects, programs and key players involved in this field of research have been listed. This paper resumes few results of this report. (authors)

  12. Aid conditionalities, international Good Manufacturing Practice standards and local production rights: a case study of local production in Nepal.

    Science.gov (United States)

    Brhlikova, Petra; Harper, Ian; Subedi, Madhusudan; Bhattarai, Samita; Rawal, Nabin; Pollock, Allyson M

    2015-06-14

    Local pharmaceutical production has been endorsed by the WHO as a means of addressing health priorities of developing countries. However, local producers of essential medicines must comply with international pharmaceutical standards in order to be eligible to compete in donor tenders. These standards determine production rights for on-patent and off-patent medicines, and guide international procurement of medicines. We reviewed the literature on the impact of Good Manufacturing Practice (GMP) on local production; a gap analysis from the literature review indicated a need for further research. Over sixty interviews were conducted with people involved in the Nepali pharmaceutical production and distribution chain from 2006 to 2009 on the GMP areas of relevance: regulatory capacity, staffing, funding and training, resourcing of GMP, inspectors' interpretation of the rules and compliance. Although Nepal producers have increased their overall share of the domestic market, only the public manufacturer, Royal Drugs, focuses on medicines for public health programmes; private producers engage mainly in brand competition for private markets, not essential medicines. Nepali regulators and producers state that implementation of GMP standards is hindered by low regulatory capacity, insufficient training of staff in the industry, financial constraints and lack of investment for upgrading capital. The transition period to mandatory compliance with WHO GMP rules is lengthy. Less than half of private producers had WHO GMP in 2013. Producers are not directly affected by international harmonisation of standards as they do not export medicines and the Nepali regulator does not enforce the WHO standards strictly. Without an international GMP certificate they cannot tender for donor dependent health programmes. In Nepal, local private manufacturers focus mainly on brand competition for private consumption not essential medicines, the government preferentially procures essential

  13. Formate Formation and Formate Conversion in Biological Fuels Production

    Directory of Open Access Journals (Sweden)

    Bryan R. Crable

    2011-01-01

    Full Text Available Biomethanation is a mature technology for fuel production. Fourth generation biofuels research will focus on sequestering CO2 and providing carbon-neutral or carbon-negative strategies to cope with dwindling fossil fuel supplies and environmental impact. Formate is an important intermediate in the methanogenic breakdown of complex organic material and serves as an important precursor for biological fuels production in the form of methane, hydrogen, and potentially methanol. Formate is produced by either CoA-dependent cleavage of pyruvate or enzymatic reduction of CO2 in an NADH- or ferredoxin-dependent manner. Formate is consumed through oxidation to CO2 and H2 or can be further reduced via the Wood-Ljungdahl pathway for carbon fixation or industrially for the production of methanol. Here, we review the enzymes involved in the interconversion of formate and discuss potential applications for biofuels production.

  14. Photochemical versus biological production of methyl iodide during Meteor 55

    Science.gov (United States)

    Richter, U.; Wallace, D.

    2003-04-01

    The flux of methyl iodide from sea to air represents the largest flux of iodine from the ocean to the atmosphere. Surface water concentrations and hence fluxes are particularly high in tropical regions. This flux may be responsible for the enrichment of iodine in the marine aerosol and may contribute to important processes in the marine boundary layer, including particle formation. Methyl iodide is commonly referred to as a biogenic gas, with both macroalgae and phytoplankton identified as important sources. On the other hand experimental and field data have shown the importance of photochemical production that is not necessarily associated directly with biological activity. During the Meteor cruise 55 along 11°N in the tropical Atlantic Ocean, a series of experiments were conducted to examine the biological vs. photochemical production of methyl iodide. A total of eight separate experiments were conducted. Production of CH3I in quartz glass flasks during 24 hour incubations (dark and natural sunlight) was measured under three experimental treatments: untreated seawater, filtered seawater (0.1 um pore size filter to exclude most phytoplankton and bacteria), and seawater that was poisoned with mercuric chloride. There were two clear findings from these experiments: (1) methyl iodide production was significantly higher in all the incubations that were exposed to the light than in the dark incubations; (2) there was no significant difference between CH3I production under the three experimental treatments. These results argue very strongly for the primary importance of photochemical production of CH3I as opposed to biogenic production at least for the tropical open ocean surface waters. Further experiments are required to investigate the reactants involved, their sources, the wavelength and depth dependence of production, etc. as well as (possibly related) sink processes.

  15. Sustainable Product Service Systems in Small and Medium Enterprises (SMEs: Opportunities in the Leather Manufacturing Industry

    Directory of Open Access Journals (Sweden)

    Ricardo J. Hernández Pardo

    2012-01-01

    Full Text Available This paper presents an approach to identify opportunities to develop sustainable Product Service Systems (PSS involving Small and Medium Enterprises (SMEs. The purpose of the research is to build understanding of how the integration of product and service design and the use of Information and Communication Technologies (ICT can contribute to identify opportunities to develop sustainable PSS involving SMEs. In order to develop the approach, research with 16 Colombian Manufacturing SMEs was carried out. A reference model and four generic types of PSS according to the relationships between product and service design and ICT are used to analyse the data. Finally, the possibility of extending the approach into a general framework to work with other industries is discussed.

  16. Exploring barriers and opportunities in adopting crowdsourcing based new product development in manufacturing SMEs

    Science.gov (United States)

    Qin, Shengfeng; Van der Velde, David; Chatzakis, Emmanouil; McStea, Terry; Smith, Neil

    2016-10-01

    Crowdsourcing is an innovative business practice of obtaining needed services, ideas, or content or even funds by soliciting contributions from a large group of people (the `Crowd'). The potential benefits of utilizing crowdsourcing in product design are well-documented, but little research exists on what are the barriers and opportunities in adopting crowdsourcing in new product development (NPD) of manufacturing SMEs. In order to answer the above questions, a Proof of Market study is carried out on crowdsourcing-based product design under an Innovate UK funded Smart project, which aims at identifying the needs, challenges and future development opportunities associated with adopting crowdsourcing strategies for NPD. The research findings from this study are reported here and can be used to guide future development of crowdsourcing-based collaborative design methods and tools and provide some practical references for industry to adopt this new and emerging collaborative design method in their business.

  17. Energy consumption in the manufacture of sawn goods and wood-based panel products

    Energy Technology Data Exchange (ETDEWEB)

    Usenius, A.

    1983-01-01

    A study was made of energy consumption in 1979 and the possibilities of saving energy in the sawmill, plywood, particle board, fibreboard, joinery, wooden houses, glulam, and wood preservation industries. The energy consumption per product unit is minimum in sawmilling, 1.38 GJ/cubic meters and maximum in fibreboard manufacturing, 9.98 GJ/t. In plywood production, the energy consumption (6.95 GJ/cubic meters) is about double that in particleboard production (3.40 GJ/cubic meters). The main part of the energy (70-85%) is heat. In the drying process about 70-85% of total energy is used in individual processes. Over half (53.9%) of the total energy consumption is in the sawmill industry, 19.2% in the plywood industry, 12.2% in the particleboard industry, and 7.2% in the fibreboard industry.

  18. Innovative Production Scheduling with Customer Satisfaction Based Measurement for the Sustainability of Manufacturing Firms

    Directory of Open Access Journals (Sweden)

    Sang-Oh Shim

    2017-12-01

    Full Text Available Scheduling problems for the sustainability of manufacturing firms in the era of the fourth industrial revolution is addressed in this research. In terms of open innovation, innovative production scheduling can be defined as scheduling using big data, cyber-physical systems, internet of things, cloud computing, mobile network, and so on. In this environment, one of the most important things is to develop an innovative scheduling algorithm for the sustainability of manufacturing firms. In this research, a flexible flowshop scheduling problem is considered with the properties of sequence-dependent setup and different process plans for jobs. In a flexible flowshop, there are serial workstations with multiple pieces of equipment that are able to process multiple lots simultaneously. Since the scheduling in this workshop is known to be extremely difficult, it is important to devise an efficient and effective scheduling algorithm. In this research, a heuristic algorithm is proposed based on a few dispatching rules and economic lot size model with the objective of minimizing total tardiness of orders. For the purposes of performance evaluation, a simulation study is conducted on randomly generated problem instances. The results imply that our proposed method outperforms the existing ones, and greatly enhances the sustainability of manufacturing firms.

  19. Optimizing production and imperfect preventive maintenance planning's integration in failure-prone manufacturing systems

    International Nuclear Information System (INIS)

    Aghezzaf, El-Houssaine; Khatab, Abdelhakim; Tam, Phuoc Le

    2016-01-01

    This paper investigates the issue of integrating production and maintenance planning in a failure-prone manufacturing system. It is assumed that the system's operating state is stochastically predictable, in terms of its operating age, and that it can accordingly be preventively maintained during preplanned periods. Preventive maintenance is assumed to be imperfect, that is when performed, it brings the manufacturing system to an operating state that lies between ‘as bad as old’ and ‘as good as new’. Only an overhauling of the system brings it to a ‘as good as new’ operating state again. A practical integrated production and preventive maintenance planning model, that takes into account the system's manufacturing capacity and its operational reliability state, is developed. The model is naturally formulated as a mixed-integer non-linear optimization problem, for which an extended mixed-integer linear reformulation is proposed. This reformulation, while it solves the proposed integrated planning problem to optimality, remains quite demanding in terms of computational time. A fix-and-optimize procedure, that takes advantage of some properties of the original model, is then proposed. The reformulation and the fix-and-optimize procedure are tested on some test instances adapted from those available in the literature. The results show that the proposed fix-and-optimize procedure performs quite well and opens new research direction for future improvements. - Highlights: • Integration of production planning and imperfect preventive maintenance is explored. • Imperfect maintenance is modeled using a fitting age reduction hybrid hazard rate. • A practical approximate optimization model for this integration is proposed. • The resulting naturally MINL optimization model is reformulated and solved as a MILP. • An effective fix-and-optimize procedure is proposed for large instances of this MILP.

  20. Understanding effect of formulation and manufacturing variables on the critical quality attributes of warfarin sodium product.

    Science.gov (United States)

    Rahman, Ziyaur; Korang-Yeboah, Maxwell; Siddiqui, Akhtar; Mohammad, Adil; Khan, Mansoor A

    2015-11-10

    Warfarin sodium (WS) is a narrow therapeutic index drug and its product quality should be thoroughly understood and monitored in order to avoid clinical performance issues. This study was focused on understanding the effect of manufacturing and formulation variables on WS product critical quality attributes (CQAs). Eight formulations were developed with lactose monohydrate (LM) or lactose anhydrous (LA), and were either wet granulated or directly compressed. Formulations were granulated either with ethanol, isopropyl alcohol (IPA) and IPA-water mixture (50:50). Formulations were characterized for IPA, water content, hardness, disintegration time (DT), assay, dissolution and drug physical forms (scanning electron microscopy (SEM), near infrared chemical imaging (NIR-CI), X-ray powder diffraction (XRPD) and solid state nuclear magnetic resonance (ssNMR)), and performed accelerated stability studies at 40°C/75% RH for three days. The DT and dissolution of directly compressed formulations were faster than wet granulated formulations. This was due to phase transformation of crystalline drug into its amorphous form as indicated by SEM, NIR-CI, XRPD and ssNMR data which itself act as a binder. Similarly, LM showed faster disintegration and dissolution than LA containing formulations. Stability results indicated an increase in hardness and DT, and a decrease in dissolution rate and extent. This was due to phase transformation of the drug and consolidation with particles' bonding. In conclusion, the CQAs of WS product were significantly affected by manufacturing and formulation variables. Published by Elsevier B.V.

  1. Environment-Aware Production Schedulingfor Paint Shops in Automobile Manufacturing: A Multi-Objective Optimization Approach.

    Science.gov (United States)

    Zhang, Rui

    2017-12-25

    The traditional way of scheduling production processes often focuses on profit-driven goals (such as cycle time or material cost) while tending to overlook the negative impacts of manufacturing activities on the environment in the form of carbon emissions and other undesirable by-products. To bridge the gap, this paper investigates an environment-aware production scheduling problem that arises from a typical paint shop in the automobile manufacturing industry. In the studied problem, an objective function is defined to minimize the emission of chemical pollutants caused by the cleaning of painting devices which must be performed each time before a color change occurs. Meanwhile, minimization of due date violations in the downstream assembly shop is also considered because the two shops are interrelated and connected by a limited-capacity buffer. First, we have developed a mixed-integer programming formulation to describe this bi-objective optimization problem. Then, to solve problems of practical size, we have proposed a novel multi-objective particle swarm optimization (MOPSO) algorithm characterized by problem-specific improvement strategies. A branch-and-bound algorithm is designed for accurately assessing the most promising solutions. Finally, extensive computational experiments have shown that the proposed MOPSO is able to match the solution quality of an exact solver on small instances and outperform two state-of-the-art multi-objective optimizers in literature on large instances with up to 200 cars.

  2. ATLAS Barrel Hadron Calorimeter: general manufacturing concepts for 300000 absorber plates mass production

    International Nuclear Information System (INIS)

    Alikov, B.A.; Budagov, Yu.A.; Bylinkin, P.M

    1998-01-01

    We summarize a 4-year (1994-1997) experience of design and research efforts which led us to the solution of 2 important tasks of a principal significance for precision assembly of one of major elements of ATLAS, - its Hadron Barrel Tile Calorimeter. These tasks were: - to develop the high tolerances (50-100 microns) technology for about 300000 units of calorimeter nuclear absorber plates mass production, - to choose the best manufacturer(s) able to satisfy shop drawings demands in a reasonable balance with some other significant criteria: production period, price acceptable geography location (transport expenses), available storage area and access ways, reliable quality control etc. For the best absorbers producers our final choice was the TATRA PLANT (Czech Republic) for 1.6 m long plates stamping (40800 units) with Argonne punching die and the MINSK TRACTOR PLANT (Belarus Republic) for smaller size plates stamping (about 240000 units). We exclude noticeable (more than 1% of the day production) tolerances violations by the specially developed QUALITY CONTROL Program

  3. Quantitative monitoring of corticosteroids in cosmetic products manufactured in Korea using LC-MS/MS.

    Science.gov (United States)

    Nam, Yun Sik; Kwon, Il Keun; Lee, Yeonhee; Lee, Kang-Bong

    2012-07-10

    Some cosmetic products manufactured in Korea for the treatment of eczema, seborrhea and psoriasis have been suspected to contain anti-inflammatory corticosteroids such as prednisolone, hydrocortisone, betamethasone, dexamethasone and triamcinolone acetonide without these ingredients being indicated on the label. Due to their severe side effects such as permenent skin atopy, these corticosteroids have to be monitored in cosmetic products from a forensic point of view. Many cosmetic product samples (N=65) have been collected from both local and online markets in Korea. The corticosteroid content of these samples was analyzed by LC-MS/MS with diagnostic ions (m/z). Linearity was studied with 0.1-10 μg/mL range in all corticosteroids. Good correlation coefficients (r(2)≥0.997) were found and the limits of quantification were 4.68-7.97 ng/mL for each of the corticosteroids. At three different concentrations spanning the linear dynamic ranges, mean recoveries were 97.2-113.5%and precisions (RSD) for intra-day and inter-day analysis were less than 8.9%. Also, accuracy (Bias %) was less than 11.8%. The results showed that between 0.76-0.94 μg/g levels of prednisolone were detected in four cosmetic products and triamcinolone acetonidewas detected with a concentration in the range of 11.5-272 μg/g in nine samples. This fact reveals that some manufacturers have arbitrarily added these corticosteroids in their cosmetic products without indicating them on the label. Thus, these cosmetic products have to be monitored and if proven illegal preparations removed from the market. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

  4. Advanced Manufacturing Technologies and Strategically Flexible Production. A Review and Outlook

    DEFF Research Database (Denmark)

    Boer, Harry

    2016-01-01

    ) led to only partial results, and were often abandoned or scaled down. At the same time, a number of soft organizational and managerial approaches and improvement programs, mostly derived from Japan, began to spread in response to the dramatic changes in the competitive environment that seemed...... to require new rationales to organize and manage production systems. However, the compatibility and coherence between changing organizational paradigms and CIM approaches were not extensively explored nor understood. This paper aims to investigate the interactions between the implementation and integration...... of Advanced Manufacturing Technologies (AMT) and the adoption of new managerial and organizational principles....

  5. Process analytical technology in continuous manufacturing of a commercial pharmaceutical product.

    Science.gov (United States)

    Vargas, Jenny M; Nielsen, Sarah; Cárdenas, Vanessa; Gonzalez, Anthony; Aymat, Efrain Y; Almodovar, Elvin; Classe, Gustavo; Colón, Yleana; Sanchez, Eric; Romañach, Rodolfo J

    2018-03-01

    The implementation of process analytical technology and continuous manufacturing at an FDA approved commercial manufacturing site is described. In this direct compaction process the blends produced were monitored with a Near Infrared (NIR) spectroscopic calibration model developed with partial least squares (PLS) regression. The authors understand that this is the first study where the continuous manufacturing (CM) equipment was used as a gravimetric reference method for the calibration model. A principal component analysis (PCA) model was also developed to identify the powder blend, and determine whether it was similar to the calibration blends. An air diagnostic test was developed to assure that powder was present within the interface when the NIR spectra were obtained. The air diagnostic test as well the PCA and PLS calibration model were integrated into an industrial software platform that collects the real time NIR spectra and applies the calibration models. The PCA test successfully detected an equipment malfunction. Variographic analysis was also performed to estimate the sampling analytical errors that affect the results from the NIR spectroscopic method during commercial production. The system was used to monitor and control a 28 h continuous manufacturing run, where the average drug concentration determined by the NIR method was 101.17% of label claim with a standard deviation of 2.17%, based on 12,633 spectra collected. The average drug concentration for the tablets produced from these blends was 100.86% of label claim with a standard deviation of 0.4%, for 500 tablets analyzed by Fourier Transform Near Infrared (FT-NIR) transmission spectroscopy. The excellent agreement between the mean drug concentration values in the blends and tablets produced provides further evidence of the suitability of the validation strategy that was followed. Copyright © 2018 Elsevier B.V. All rights reserved.

  6. Biological treatment of chicken feather waste for improved biogas production

    Institute of Scientific and Technical Information of China (English)

    Gergely Forgács; Saeid Alinezhad; Amir Mirabdollah; Elisabeth Feuk-Lagerstedt; Ilona Sárvári Horwáth

    2011-01-01

    A two-stage system was developed which combines the biological degradation of keratin-rich waste with the production of biogas.Chicken feather waste was treated biologically with a recombinant Bacillus megaterium strain showing keratinase activity prior to biogas production.Chopped,autoclaved chicken feathers (4%,W/V) were completely degraded,resulting in a yellowish fermentation broth with a level of 0.51 mg/mL soluble proteins after 8 days of cultivation of the recombinant strain.During the subsequent anaerobic batch digestion experiments,methane production of 0.35 Nm3/kg dry feathers (i.e.,0.4 Nm3/kg volatile solids of feathers),corresponding to 80% of the theoretical value on proteins,was achieved from the feather hydrolyzates,independently of the prehydrolysis time period of 1,2 or 8 days.Cultivation with a native keratinase producing strain,Bacillus licheniformis resulted in only 0.25 mg/mL soluble proteins in the feather hydrolyzate,which then was digested achieving a maximum accumulated methane production of 0.31 Nm3/kg dry feathers.Feather hydrolyzates treated with the wild type B.megaterium produced 0.21 Nm3 CH4/kg dry feathers as maximum yield.

  7. The study of production performance of water heater manufacturing by using simulation method

    Science.gov (United States)

    Iqbal, M.; Bamatraf, OAA; Tadjuddin, M.

    2018-02-01

    In industrial companies, as demand increases, decision-making to increase production becomes difficult due to the complexity of the model systems. Companies are trying to find the optimum methods to tackle such problems so that resources are utilized and production is increased. One line system of a manufacturing company in Malaysia was considered in this research. The Company produces several types of water heater and each type went into many processes, which was divided into twenty six sections. Each section has several operations. The main type of the product was 10G water heater which is produced most compare to other types, hence it was taken under consideration to be studied in this research. It was difficult to find the critical section that could improve the productions of the company. This research paper employed Delmia Quest software, Distribution Analyser software and Design of Experiment (DOE software) to simulate one model system taken from the company to be studied and to find the critical section that will improve the production system. As a result, assembly of inner and outer tank section were found to be the bottleneck section. Adding one section to the bottleneck increases the production rate by four products a day. The buffer size is determined by the experiment was six items.

  8. Essential Aspects in Assessing the Safety Impact of Interactions between a Drug Product and Its Associated Manufacturing System.

    Science.gov (United States)

    Jenke, Dennis

    2012-01-01

    An emerging trend in the biotechnology industry is the utilization of plastic components in manufacturing systems for the production of an active pharmaceutical ingredient (API) or a finished drug product (FDP). If the API, the FDP, or any solution used to generate them (for example, process streams such as media, buffers, and the like) come in contact with a plastic at any time during the manufacturing process, there is the potential that substances leached from the plastic may accumulate in the API or FDP, affecting safety and/or efficacy. In this article the author develops a terminology that addresses process streams associated with the manufacturing process. Additionally, the article outlines the safety assessment process for manufacturing systems, specifically addressing the topics of risk management and the role of compendial testing. Finally, the proper use of vendor-supplied extractables information is considered. Manufacturing suites used to produce biopharmaceuticals can include components that are made out of plastics. Thus it is possible that substances could leach out of the plastics and into manufacturing solutions, and it is further possible that such leachables could accumulate in the pharmaceutical product. In this article, the author develops a terminology that addresses process streams associated with the manufacturing process. Additionally, the author proposes a process by which the impact on product safety of such leached substances can be assessed.

  9. The comparison analysis of total factor productivity and eco-efficiency in China's cement manufactures

    International Nuclear Information System (INIS)

    Long, Xingle; Zhao, Xicang; Cheng, Faxin

    2015-01-01

    This paper mainly compares total factor productivity and eco-efficiency in China's cement manufactures from 2005 to 2010. First, we evaluate total factor productivity and eco-efficiency of China's cement manufactures through distance function and directional slack-based measure (DSBM) respectively. Furthermore, we also explore the difference of total factor productivity and eco-efficiency. Last, we investigate the determinants of Malmquist, Mamlquist–Luenberger of China's cement manufactures through random-effect Tobit and bootstrap truncated econometric methods. We find that there are some gaps between Malmquist and Mamlquist–Luenberger of China's cement manufactures. Per labor cement industry value has U-shape relationship with both Malmquist and Malmquist–Luenberger. It is necessary to adopt advanced technology to reduce pollutant emissions. -- Highlights: •Eco-efficiency of cement manufactures is evaluated through slack-based measure. •Eco-efficiency of China's cement manufactures has biases with total factor productivity. •Environmental Kuznets curve is existed for China's cement manufactures

  10. Micro Manufacturing

    DEFF Research Database (Denmark)

    Hansen, Hans Nørgaard

    2003-01-01

    Manufacturing deals with systems that include products, processes, materials and production systems. These systems have functional requirements, constraints, design parameters and process variables. They must be decomposed in a systematic manner to achieve the best possible system performance....... If a micro manufacturing system isn’t designed rationally and correctly, it will be high-cost, unreliable, and not robust. For micro products and systems it is a continuously increasing challenge to create the operational basis for an industrial production. As the products through product development...... processes are made applicable to a large number of customers, the pressure in regard to developing production technologies that make it possible to produce the products at a reasonable price and in large numbers is growing. The micro/nano manufacturing programme at the Department of Manufacturing...

  11. Sustained climate warming drives declining marine biological productivity

    Science.gov (United States)

    Moore, J. Keith; Fu, Weiwei; Primeau, Francois; Britten, Gregory L.; Lindsay, Keith; Long, Matthew; Doney, Scott C.; Mahowald, Natalie; Hoffman, Forrest; Randerson, James T.

    2018-03-01

    Climate change projections to the year 2100 may miss physical-biogeochemical feedbacks that emerge later from the cumulative effects of climate warming. In a coupled climate simulation to the year 2300, the westerly winds strengthen and shift poleward, surface waters warm, and sea ice disappears, leading to intense nutrient trapping in the Southern Ocean. The trapping drives a global-scale nutrient redistribution, with net transfer to the deep ocean. Ensuing surface nutrient reductions north of 30°S drive steady declines in primary production and carbon export (decreases of 24 and 41%, respectively, by 2300). Potential fishery yields, constrained by lower–trophic-level productivity, decrease by more than 20% globally and by nearly 60% in the North Atlantic. Continued high levels of greenhouse gas emissions could suppress marine biological productivity for a millennium.

  12. First update of the International Xenotransplantation Association consensus statement on conditions for undertaking clinical trials of porcine islet products in type 1 diabetes--Chapter 3: Porcine islet product manufacturing and release testing criteria.

    Science.gov (United States)

    Rayat, Gina R; Gazda, Lawrence S; Hawthorne, Wayne J; Hering, Bernhard J; Hosking, Peter; Matsumoto, Shinichi; Rajotte, Ray V

    2016-01-01

    In the 2009 IXA consensus, the requirements for the quality and control of manufacturing of porcine islet products were based on the U.S. regulatory framework where the porcine islet products fall within the definition of somatic cell therapy under the statutory authority of the U.S. Food and Drug Administration (FDA). In addition, porcine islet products require pre-market approval as a biologic product under the Public Health Services Act and they meet the definition of a drug under the Federal Food, Drug, and Cosmetic Act (FD&C Act). Thus, they are subject to applicable provisions of the law and as such, control of manufacturing as well as reproducibility and consistency of porcine islet products, safety of porcine islet products, and characterization of porcine islet products must be met before proceeding to clinical trials. In terms of control of manufacturing as well as reproducibility and consistency of porcine islet products, the manufacturing facility must be in compliance with current Good Manufacturing Practices (cGMP) guidelines appropriate for the initiation of Phase 1/2 clinical trials. Sponsors intending to conduct a Phase 1/2 trial of islet xenotransplantation products must be able to demonstrate the safety of the product through the establishment of particular quality assurance and quality control procedures. All materials (including animal source and pancreas) used in the manufacturing process of the porcine islet products must be free of adventitious agents. The final porcine islet product must undergo tests for the presence of these adventitious agents including sterility, mycoplasma (if they are cultured), and endotoxin. Assessments of the final product must include the safety specifications mentioned above even if the results are not available until after release as these data would be useful for patient diagnosis and treatment if necessary. In addition, a plan of action must be in place for patient notification and treatment in case the

  13. Characterization of uranium corrosion products involved in the March 13, 1998 fuel manufacturing facility pyrophoric event

    International Nuclear Information System (INIS)

    Totemeier, T.C.

    1999-01-01

    Uranium metal corrosion products from ZPPR fuel plates involved in the March 13, 1998 pyrophoric event in the Fuel Manufacturing Facility at Argonne National Laboratory-West were characterized using thermo-gravimetric analysis, X-ray diffraction, and BET gas sorption techniques. Characterization was performed on corrosion products in several different conditions: immediately after separation from the source metal, after low-temperature passivation, after passivation and extended vault storage, and after burning in the pyrophoric event. The ignition temperatures and hydride fractions of the corrosion product were strongly dependent on corrosion extent. Corrosion products from plates with corrosion extents less than 0.7% did not ignite in TGA testing, while products from plates with corrosion extents greater than 1.2% consistently ignited. Corrosion extent is defined as mass of corrosion products divided by the total mass of uranium. The hydride fraction increased with corrosion extent. There was little change in corrosion product properties after low-temperature passivation or vault storage. The burned products were not reactive and contained no hydride; the principal constituents were UO 2 and U 3 O 7 . The source of the event was a considerable quantity of reactive hydride present in the corrosion products. No specific ignition mechanism could be conclusively identified. The most likely initiator was a static discharge in the corrosion product from the 14th can as it was poured into the consolidation can. The available evidence does not support scenarios in which the powder in the consolidation can slowly self-heated to the ignition point, or in which the powder in the 14th can was improperly passivated

  14. Characterization of uranium corrosion products involved in the March 13, 1998 fuel manufacturing facility pyrophoric event.

    Energy Technology Data Exchange (ETDEWEB)

    Totemeier, T.C.

    1999-04-26

    Uranium metal corrosion products from ZPPR fuel plates involved in the March 13, 1998 pyrophoric event in the Fuel Manufacturing Facility at Argonne National Laboratory-West were characterized using thermo-gravimetric analysis, X-ray diffraction, and BET gas sorption techniques. Characterization was performed on corrosion products in several different conditions: immediately after separation from the source metal, after low-temperature passivation, after passivation and extended vault storage, and after burning in the pyrophoric event. The ignition temperatures and hydride fractions of the corrosion product were strongly dependent on corrosion extent. Corrosion products from plates with corrosion extents less than 0.7% did not ignite in TGA testing, while products from plates with corrosion extents greater than 1.2% consistently ignited. Corrosion extent is defined as mass of corrosion products divided by the total mass of uranium. The hydride fraction increased with corrosion extent. There was little change in corrosion product properties after low-temperature passivation or vault storage. The burned products were not reactive and contained no hydride; the principal constituents were UO{sub 2} and U{sub 3}O{sub 7}. The source of the event was a considerable quantity of reactive hydride present in the corrosion products. No specific ignition mechanism could be conclusively identified. The most likely initiator was a static discharge in the corrosion product from the 14th can as it was poured into the consolidation can. The available evidence does not support scenarios in which the powder in the consolidation can slowly self-heated to the ignition point, or in which the powder in the 14th can was improperly passivated.

  15. Manufacturing processes in the textile industry. Expert Systems for fabrics production

    Directory of Open Access Journals (Sweden)

    Juan BULLON

    2017-03-01

    Full Text Available The textile industry is characterized by the economic activity whose objective is the production of fibres, yarns, fabrics, clothing and textile goods for home and decoration,as well as technical and industrial purposes. Within manufacturing, the Textile is one of the oldest and most complex sectors which includes a large number of sub-sectors covering the entire production cycle, from raw materials and intermediate products, to the production of final products. Textile industry activities present different subdivisions, each with its own traits. The length of the textile process and the variety of its technical processes lead to the coexistence of different sub-sectors in regards to their business structure and integration. The textile industry is developing expert systems applications to increase production, improve quality and reduce costs. The analysis of textile designs or structures includes the use of mathematical models to simulate the behavior of the textile structures (yarns, fabrics and knitting. The Finite Element Method (FEM has largely facilitated the prediction of the behavior of that textile structure under mechanical loads. For classification problems Artificial Neural Networks (ANNs haveproved to be a very effective tool as a quick and accurate solution. The Case-Based Reasoning (CBR method proposed in this study complements the results of the finite element simulation, mathematical modeling and neural networks methods.

  16. Assimilation Patterns in the Use of Advanced Manufacturing Technologies in SMEs: Exploring their Effects on Product Innovation Performance

    Directory of Open Access Journals (Sweden)

    Sylvestre Uwizeyemungu

    2015-10-01

    Full Text Available Manufacturing small and medium-sized enterprises (SMEs are more and more adopting advanced manufacturing technologies (AMT aimed at fostering product innovation process, improving product quality, streamlining the production process, and gaining productivity. In this study, we analyze the relationship between AMT proficiency levels in manufacturing SMEs and product innovation performance. Using data from 616 manufacturing SMEs, and considering a wide range of various AMT (20 different types of AMT grouped into 5 categories, we derived three AMT assimilation patterns through a cluster analysis procedure combining hierarchical and non-hierarchical clustering algorithms. The analysis of the relationship between AMT assimilation patterns and product innovation performance shows a rather unexpected picture: in spite of the existence of clearly distinct patterns of AMT assimilation, we find no significant relationship between any pattern and product innovation performance. Instead, we find the organizational and environmental context of SMEs to be more determinant for product innovation performance than any of the AMT assimilation patterns. From a practical point of view, this study indicates that manufacturing SMEs managers interested in fostering their innovation capabilities through AMT assimilation need to be aware of the contingency effects of their organizational size, age, and sector of activity.

  17. Microbiological Control of Flour-Manufacture: Dissemination of Mycotoxins Producing Fungi in Cereal Products

    Directory of Open Access Journals (Sweden)

    T.D. Doolotkeldieva

    2010-01-01

    Full Text Available Wheat grain and its products are widely consumed as fodder and basic daily food stuffs in Kyrgyzstan. Mycobiota is known to produce hazardous effects to a consumer since it produces mycotoxins. Henceforth, mycobiota starting from the field stage to flour, grain and flour samples were selected for mycological analysis from eight sites of flour manufacture: grain stored in storehouses before milling, mechanically cleaned grain, washed grain, grain dried and prepared for mill, roughly-milled flour, first grade flour and high grade flour. The samples were analyzed using classical mycological and immunoassay methods in order to detect mycotoxins producing fungi species. We isolated overall 27 species belonging to 7 genera. Mycotoxins producing species like Aspergillus flavus, Aspergillus ochraceus and Penicillium cyclopium were detected in the stored grains and in mechanically-cleaned grains. The species of Penicillium, Alternaria and Fusarium genera dominated in roughly-milled flour samples, so this site of flour manufacture still has a risk and danger of contamination with mycotoxins producing fungus. Only the final product i.e. the high grade flour lacked any fungal contamination. We recommend to scrutinize flour samples at the last stages of processing, particularly in the mills like B1, C1 and C4.

  18. Particle shedding from peristaltic pump tubing in biopharmaceutical drug product manufacturing.

    Science.gov (United States)

    Saller, Verena; Matilainen, Julia; Grauschopf, Ulla; Bechtold-Peters, Karoline; Mahler, Hanns-Christian; Friess, Wolfgang

    2015-04-01

    In a typical manufacturing setup for biopharmaceutical drug products, the fill and dosing pump is placed after the final sterile filtration unit in order to ensure adequate dispensing accuracy and avoid backpressure peaks. Given the sensitivity of protein molecules, peristaltic pumps are often preferred over piston pumps. However, particles may be shed from the silicone tubing employed. In this study, particle shedding and a potential turbidity increase during peristaltic pumping of water and buffer were investigated using three types of commercially available silicone tubing. In the recirculates, mainly particles of around 200 nm next to a very small fraction of particles in the lower micrometer range were found. Using 3D laser scanning microscopy, surface roughness of the inner tubing surface was found to be a determining factor for particle shedding from silicone tubing. As the propensity toward particle shedding varied between tubing types and also cannot be concluded from manufacturer's specifications, individual testing with the presented methods is recommended during tubing qualification. Choosing low abrasive tubing can help to further minimize the very low particle counts to be expected in pharmaceutical drug products. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  19. Molecular biology in studies of oceanic primary production

    International Nuclear Information System (INIS)

    LaRoche, J.; Falkowski, P.G.; Geider, R.

    1992-01-01

    Remote sensing and the use of moored in situ instrumentation has greatly improved our ability to measure phytoplankton chlorophyll and photosynthesis on global scales with high temporal resolution. However, the interpretation of these measurements and their significance with respect to the biogeochemical cycling of carbon relies on their relationship with physiological and biochemical processes in phytoplankton. For example, the use of satellite images of surface chlorophyll to estimate primary production is often based on the functional relationship between photosynthesis and irradiance. A variety of environmental factors such as light, temperature, nutrient availability affect the photosynthesis/irradiance (P vs I) relationship in phytoplankton. We present three examples showing how molecular biology can be used to provide basic insight into the factors controlling primary productivity at three different levels of complexity: 1. Studies of light intensity regulation in unicellular alga show how molecular biology can help understand the processing of environmental cues leading to the regulation of photosynthetic gene expression. 2. Probing of the photosynthetic apparatus using molecular techniques can be used to test existing mechanistic models derived from the interpretation of physiological and biophysical measurements. 3. Exploratory work on the expression of specific proteins during nutrient-limited growth of phytoplankton may lead to the identification and production of molecular probes for field studies

  20. Integrating Hazardous Materials Characterization and Assessment Tools to Guide Pollution Prevention in Electronic Products and Manufacturing

    Science.gov (United States)

    Lam, Carl

    Due to technology proliferation, the environmental burden attributed to the production, use, and disposal of hazardous materials in electronics have become a worldwide concern. The major theme of this dissertation is to develop and apply hazardous materials assessment tools to systematically guide pollution prevention opportunities in the context of electronic product design, manufacturing and end-of-life waste management. To this extent, a comprehensive review is first provided on describing hazard traits and current assessment methods to evaluate hazardous materials. As a case study at the manufacturing level, life cycle impact assessment (LCIA)-based and risk-based screening methods are used to quantify chemical and geographic environmental impacts in the U.S. printed wiring board (PWB) industry. Results from this industrial assessment clarify priority waste streams and States to most effectively mitigate impact. With further knowledge of PWB manufacturing processes, select alternative chemical processes (e.g., spent copper etchant recovery) and material options (e.g., lead-free etch resist) are discussed. In addition, an investigation on technology transition effects for computers and televisions in the U.S. market is performed by linking dynamic materials flow and environmental assessment models. The analysis forecasts quantities of waste units generated and maps shifts in environmental impact potentials associated with metal composition changes due to product substitutions. This insight is important to understand the timing and waste quantities expected and the emerging toxic elements needed to be addressed as a consequence of technology transition. At the product level, electronic utility meter devices are evaluated to eliminate hazardous materials within product components. Development and application of a component Toxic Potential Indicator (TPI) assessment methodology highlights priority components requiring material alternatives. Alternative

  1. The Transportation Logistics of Manufactured Products in the Colombian Internal Market

    Directory of Open Access Journals (Sweden)

    Edisson Castro Escobar

    2014-12-01

    Full Text Available This paper tracks the transport logistics of the Colombian manufacturing industry in the domestic market, analyzing the direction and the volume of the cargo moved by road. The study is intended to identify some sectorial and regional enclaves of the industry that could be strategic for market diversification and to facilitate production chains. Estimates of land freight movements are made based on the origin-destination survey carried out by the Ministry of Transportation in 2008. The different regional and sectorial flows are projected through a geodetic network model. The results indicate that regional differences in product specialization explain the movement of cargo from specific industries, while in other cases there are no significant flows because the industries largely serve local markets.

  2. Web-Based Implementation of E-Marketing to Support Product Marketing of Chemical Manufacturing Company

    Directory of Open Access Journals (Sweden)

    Riswan Efendi Tarigan

    2015-10-01

    Full Text Available Currently, many company’s marketing strategies are limited only to face-to-face communication, telephone, facsimile, company portfolio, and product brochures. However, those marketing strategies are well- known to have limited impacts. Therefore, the presence of e-marketing as one of the marketing strategies would be appropriate to cover the weaknesses and to solve a number of the marketing problems. The purpose of this study is to discuss matters related to marketing, such    as, proposing a marketing plan using website, expanding marketing segment, and introducing existing  products for a chemical manufacturing company. The adopted research method is a descriptive method where the study is directly performed on the research object to acquire necessary data. The collected data are further analyzed using the Porter’s Five Force and SWOT analysis. Fi- nally, the work provides a number of recommendations for implementing e-marketing strategies to support the company business.

  3. ROBOTICALLY ENHANCED ADVANCED MANUFACTURING CONCEPTS TO OPTIMIZE ENERGY, PRODUCTIVITY, AND ENVIRONMENTAL PERFORMANCE

    Energy Technology Data Exchange (ETDEWEB)

    Larry L. Keller; Joseph M. Pack; Robert V. Kolarik II

    2007-11-05

    In the first phase of the REML project, major assets were acquired for a manufacturing line for follow-on installation, capability studies and optimization. That activity has been documented in the DE-FC36-99ID13819 final report. In this the second phase of the REML project, most of the major assets have been installed in a manufacturing line arrangement featuring a green cell, a thermal treatment cell and a finishing cell. Most of the secondary and support assets have been acquired and installed. Assets have been integrated with a commercial, machine-tending gantry robot in the thermal treatment cell and with a low-mass, high-speed gantry robot in the finish cell. Capabilities for masterless gauging of product’s dimensional and form characteristics were advanced. Trial production runs across the entire REML line have been undertaken. Discrete event simulation modeling has aided in line balancing and reduction of flow time. Energy, productivity and cost, and environmental comparisons to baselines have been made. Energy The REML line in its current state of development has been measured to be about 22% (338,000 kVA-hrs) less energy intensive than the baseline conventional low volume line assuming equivalent annual production volume of approximately 51,000 races. The reduction in energy consumption is largely attributable to the energy reduction in the REML thermal treatment cell where the heating devices are energized on demand and are appropriately sized to the heating load of a near single piece flow line. If additional steps such as power factor correction and use of high-efficiency motors were implemented to further reduce energy consumption, it is estimated, but not yet demonstrated, that the REML line would be about 30% less energy intensive than the baseline conventional low volume line assuming equivalent annual production volume. Productivity The capital cost of an REML line would be roughly equivalent to the capital cost of a new conventional line. The

  4. Research on the Governance Mechanism of Aviation Complex Product Manufacturing Supply Chain Based on Dynamic Game Theory

    Directory of Open Access Journals (Sweden)

    Wang Nan

    2016-01-01

    Full Text Available In the manufacturing process of aeronautical complex products, for the following problems: develop long production cycle, a large number of ancillary products, a plurality of participating units, etc, and the status of the frequency of quality problems, using single-phase static game model in the case of asymmetric information, study on Supplier Quality insufficient investment, which resulting in opportunistic behaviour reasons. And using KMRW dynamic game model, we quantitative analysis the mechanism and crucial role of reputation mechanisms to ensure aeronautical complex product manufacturing supply chain and effective operation.

  5. Applications of dimensional micro metrology to the product and process quality control in manufacturing of precision polymer micro components

    DEFF Research Database (Denmark)

    Tosello, Guido; Hansen, Hans Nørgaard; Gasparin, Stefania

    2009-01-01

    Precision manufacturing of micro injection moulded (mu IM) components presents challenges in terms of quality control due to the miniaturization of product dimensions and tolerances. This paper addresses product compliance with specifications, focusing on tolerances of dimensions and position on mu...... IM components selected from industrial production. Two systems were analysed: a tactile coordinate measuring machine (CMM) with sub-micrometer uncertainty and an optical CMM allowing fast measurements suitable for in-line quality control. Product quality control capability, measuring uncertainty...... and calibration guidelines are discussed for both systems. Finally, a new approach for the manufacturing of hybrid micro polymer-metal calibrated objects is proposed....

  6. Biological hydrogen production from biomass by thermophilic bacteria

    International Nuclear Information System (INIS)

    Claassen, P.A.M.; Mars, A.E.; Budde, M.A.W.; Lai, M.; de Vrije, T.; van Niel, E.W.J.

    2006-01-01

    To meet the reduction of the emission of CO 2 imposed by the Kyoto protocol, hydrogen should be produced from renewable primary energy. Besides the indirect production of hydrogen by electrolysis using electricity from renewable resources, such as sunlight, wind and hydropower, hydrogen can be directly produced from biomass. At present, there are two strategies for the production of hydrogen from biomass: the thermochemical technology, such as gasification, and the biotechnological approach using micro-organisms. Biological hydrogen production delivers clean hydrogen with an environmental-friendly technology and is very suitable for the conversion of wet biomass in small-scale applications, thus having a high chance of becoming an economically feasible technology. Many micro-organisms are able to produce hydrogen from mono- and disaccharides, starch and (hemi)cellulose under anaerobic conditions. The anaerobic production of hydrogen is a common phenomenon, occurring during the process of anaerobic digestion. Here, hydrogen producing micro-organisms are in syn-trophy with methanogenic bacteria which consume the hydrogen as soon as it is produced. In this way, hydrogen production remains obscure and methane is the end-product. By uncoupling hydrogen production from methane production, hydrogen becomes available for recovery and exploitation. This study describes the use of extreme thermophilic bacteria, selected because of a higher hydrogen production efficiency as compared to mesophilic bacteria, for the production of hydrogen from renewable resources. As feedstock energy crops like Miscanthus and Sorghum bicolor and waste streams like domestic organic waste, paper sludge and potato steam peels were used. The feedstock was pretreated and/or enzymatically hydrolyzed prior to fermentation to make a fermentable substrate. Hydrogen production by Caldicellulosiruptor saccharolyticus, Thermotoga elfii and T. neapolitana on all substrates was observed. Nutrient

  7. Precision manufacturing

    CERN Document Server

    Dornfeld, David

    2008-01-01

    Today there is a high demand for high-precision products. The manufacturing processes are now highly sophisticated and derive from a specialized genre called precision engineering. Precision Manufacturing provides an introduction to precision engineering and manufacturing with an emphasis on the design and performance of precision machines and machine tools, metrology, tooling elements, machine structures, sources of error, precision machining processes and precision process planning. As well as discussing the critical role precision machine design for manufacturing has had in technological developments over the last few hundred years. In addition, the influence of sustainable manufacturing requirements in precision processes is introduced. Drawing upon years of practical experience and using numerous examples and illustrative applications, David Dornfeld and Dae-Eun Lee cover precision manufacturing as it applies to: The importance of measurement and metrology in the context of Precision Manufacturing. Th...

  8. Yeast synthetic biology for the production of recombinant therapeutic proteins.

    Science.gov (United States)

    Kim, Hyunah; Yoo, Su Jin; Kang, Hyun Ah

    2015-02-01

    The production of recombinant therapeutic proteins is one of the fast-growing areas of molecular medicine and currently plays an important role in treatment of several diseases. Yeasts are unicellular eukaryotic microbial host cells that offer unique advantages in producing biopharmaceutical proteins. Yeasts are capable of robust growth on simple media, readily accommodate genetic modifications, and incorporate typical eukaryotic post-translational modifications. Saccharomyces cerevisiae is a traditional baker's yeast that has been used as a major host for the production of biopharmaceuticals; however, several nonconventional yeast species including Hansenula polymorpha, Pichia pastoris, and Yarrowia lipolytica have gained increasing attention as alternative hosts for the industrial production of recombinant proteins. In this review, we address the established and emerging genetic tools and host strains suitable for recombinant protein production in various yeast expression systems, particularly focusing on current efforts toward synthetic biology approaches in developing yeast cell factories for the production of therapeutic recombinant proteins. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permission@oup.com.

  9. Natural products as a resource for biologically active compounds

    International Nuclear Information System (INIS)

    Hanke, F.J.

    1986-01-01

    The goal of this study was to investigate various sources of biologically active natural products in an effort to identify the active pesticidal compounds involved. The study is divided into several parts. Chapter 1 contains a discussion of several new compounds from plant and animal sources. Chapter 2 introduces a new NMR technique. In section 2.1 a new technique for better utilizing the lanthanide relaxation agent Gd(fod) 3 is presented which allows the predictable removal of resonances without line broadening. Section 2.2 discusses a variation of this technique for use in an aqueous solvent by applying this technique towards identifying the binding sites of metals of biological interest. Section 2.3 presents an unambiguous 13 C NMR assignment of melibiose. Chapter 3 deals with work relating to the molting hormone of most arthropods, 20-hydroxyecdysone. Section 3.1 discusses the use of two-dimensional NMR (2D NMR) to assign the 1 H NMR spectrum of this biologically important compound. Section 3.2 presents a new application for Droplet countercurrent chromatography (DCCC). Chapter 4 presents a basic improvement to the commercial DCCC instrument that is currently being applied to future commercial instruments. Chapter 5 discusses a curious observation of the effects that two previously known compounds, nagilactone C and (-)-epicatechin, have on lettuce and rice and suggest a possible new role for the ubiquitous flavanol (-)-epicatechin in plants

  10. Current good manufacturing practice production of an oncolytic recombinant vesicular stomatitis viral vector for cancer treatment.

    Science.gov (United States)

    Ausubel, L J; Meseck, M; Derecho, I; Lopez, P; Knoblauch, C; McMahon, R; Anderson, J; Dunphy, N; Quezada, V; Khan, R; Huang, P; Dang, W; Luo, M; Hsu, D; Woo, S L C; Couture, L

    2011-04-01

    Vesicular stomatitis virus (VSV) is an oncolytic virus currently being investigated as a promising tool to treat cancer because of its ability to selectively replicate in cancer cells. To enhance the oncolytic property of the nonpathologic laboratory strain of VSV, we generated a recombinant vector [rVSV(MΔ51)-M3] expressing murine gammaherpesvirus M3, a secreted viral chemokine-binding protein that binds to a broad range of mammalian chemokines with high affinity. As previously reported, when rVSV(MΔ51)-M3 was used in an orthotopic model of hepatocellular carcinoma (HCC) in rats, it suppressed inflammatory cell migration to the virus-infected tumor site, which allowed for enhanced intratumoral virus replication leading to increased tumor necrosis and substantially prolonged survival. These encouraging results led to the development of this vector for clinical translation in patients with HCC. However, a scalable current Good Manufacturing Practice (cGMP)-compliant manufacturing process has not been described for this vector. To produce the quantities of high-titer virus required for clinical trials, a process that is amenable to GMP manufacturing and scale-up was developed. We describe here a large-scale (50-liter) vector production process capable of achieving crude titers on the order of 10(9) plaque-forming units (PFU)/ml under cGMP. This process was used to generate a master virus seed stock and a clinical lot of the clinical trial agent under cGMP with an infectious viral titer of approximately 2 × 10(10) PFU/ml (total yield, 1 × 10(13) PFU). The lot has passed all U.S. Food and Drug Administration-mandated release testing and will be used in a phase 1 clinical translational trial in patients with advanced HCC.

  11. Recent advances on biological production of difructose dianhydride III.

    Science.gov (United States)

    Zhu, Yingying; Yu, Shuhuai; Zhang, Wenli; Zhang, Tao; Guang, Cuie; Mu, Wanmeng

    2018-04-01

    Difructose dianhydride III (DFA III) is a cyclic difructose containing two reciprocal glycosidic linkages. It is easily generated with a small amount by sucrose caramelization and thus occurs in a wide range of food-stuffs during food processing. DFA III has half sweetness but only 1/15 energy of sucrose, showing potential industrial application as low-calorie sucrose substitute. In addition, it displays many benefits including prebiotic effect, low cariogenicity property, and hypocholesterolemic effect, and improves absorption of minerals, flavonoids, and immunoglobulin G. DFA III is biologically produced from inulin by inulin fructotransferase (IFTase, EC 4.2.2.18). Plenty of DFA III-producing enzymes have been identified. The crystal structure of inulin fructotransferase has been determined, and its molecular modification has been performed to improve the catalytic activity and structural stability. Large-scale production of DFA III has been studied by various IFTases, especially using an ultrafiltration membrane bioreactor. In this article, the recent findings on physiological effects of DFA III are briefly summarized; the research progresses on identification, expression, and molecular modification of IFTase and large-scale biological production of DFA III by IFTase are reviewed in detail.

  12. Evaluation of the California Safer Consumer Products Regulation and the impact on consumers and product manufacturers.

    Science.gov (United States)

    Cowan, Dallas M; Kingsbury, Tony; Perez, Angela L; Woods, Tyler A; Kovochich, Michael; Hill, Denise S; Madl, Amy K; Paustenbach, Dennis J

    2014-02-01

    Chemistry enables more than 95% of products in the marketplace. Over the past 20 years, various entities began to generate inventories of chemicals ("chemical watch lists") potentially associated with human or environmental health risks. Some lists included thousands of chemicals, while others listed only a few chemistries with limited properties or toxicological endpoints (e.g., neurotoxicants). Enacted on October 1, 2013, the California Safer Consumer Products Regulation (SCP) utilized data from chemical inventory lists to create one master list. This paper aims to discuss the background and requirements of this regulation. Additionally, we wanted to understand the universe of Candidate Chemicals identified by the Regulation. Data from all 23 chemical lists identified in the SCP Regulation were entered into a database. The most prevalent chemicals among the ∼2900 chemicals are identified, including the most prevalent chemical, lead, appearing on 65% of lists, followed by DEHP (52%), perchloroethylene (48%), and benzene (48%). Our results indicated that the most prevalent Candidate Chemicals were either persistent, bioaccumulative, carcinogenic, or reprotoxic. This regulation will have wide-ranging impact in California and throughout the global supply chain, which is highlighted through selected examples and case studies. Copyright © 2013 Elsevier Inc. All rights reserved.

  13. The Application of Lean Manufacturing for Operation Improvement: A Case Study of Black Cough Medicine Production in Indonesia

    Directory of Open Access Journals (Sweden)

    Pramadona Pramadona

    2013-09-01

    Full Text Available Nowadays, the pharmaceutical industry has a market tends to be unstable and volatile in meeting customer needs. This is due to the economic crisis that occurred in different parts of the world. The pharmaceutical industry currently uses good manufacturing practices (cGMP to ensure that products are consistently produced and controlled according to the required standards. Pharmaceutical industry slowly started to move from cGMP to lean manufacturing that focused on reducing operating costs while ensuring compliance. The purpose of this paper is to analyze the usage of lean manufacturing instead of the usage of cGMP to eliminate wastes. To conduct this study, literature review and company visit has been done. This analysis was applied by using value stream mapping (VSM and 7-wastes methodology to analyze the problems in the OBH (Black Cough Medicine production line one of the pharmaceutical industry in Bandung, Indonesia. For the improvement, the lean manufacturing approach has been carried out and the future VSM has been developed. Finding reveals that the application of lean manufacturing in the cGMP environment helps the company to eliminate wastes in reducing lead time and cycle time in the manufacturing process. Keywords: pharmaceutical industry, cGMP, lean manufacturing, value stream mapping, 7-wastes.

  14. A product-process approach for development of the manufacturing footprint

    DEFF Research Database (Denmark)

    Farooq, Sami; Yang, Cheng; Johansen, John

    2009-01-01

    to ever changing global business environment there are certain other external factors that act as drivers for the manufacturing facility development process and therefore should be given considerable importance as they play a major role in defining the future footprint of a manufacturing organisation....... elaborating the development and establishment of various manufacturing facilities of a Danish pump manufacturer is then described. The discussion from the case leads to the conclusion that developing new manufacturing facilities can be explained using existing theories of manufacturing strategy. However due...

  15. 78 FR 60884 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2013-10-02

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug... public. Name of Committee: Vaccines and Related Biological Products Advisory Committee. General Function... Immunoregulation, Division of Viral Products, Office of Vaccines Research and Review, Center for Biologics...

  16. 77 FR 3780 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2012-01-25

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug... public. Name of Committee: Vaccines and Related Biological Products Advisory Committee. General Function... Products, Office of Vaccines Research and Review, Center for Biologics Evaluation and Research, FDA. The...

  17. 76 FR 44016 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2011-07-22

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug... public. Name of Committee: Vaccines and Related Biological Products Advisory Committee. General Function... Allergenic Products, Office of Vaccines Research and Review, Center for Biologics Evaluation and Research...

  18. Application of Lean Manufacturing Tools in a Garment Industry as a Strategy for Productivity Improvement

    Directory of Open Access Journals (Sweden)

    Rebecca M. Nunesca

    2015-11-01

    Full Text Available This study aimed to use and apply lean tools as ways of improving manufacturing systems that lead to reduction of wastes and standardization of cycle time. Model A in Line 1 at sewing section was the focus of the study. The researcher used questionnaires, 5S Audit checklists, and Time Study forms in information-gathering and cycle time-computation. Based on the observation done, the company does not have a standard operation time. Similarly, the researcher observed non-value activities such as unnecessary transportation and manual counting, and there were also product defects due to poor 5S and WIP inventories. After considering lean tools, using process flow and cycle time analysis, the standard time was determined. Likewise, the non-value added activities were reduced, thus productivity was improved. After lean implementation, 100% efficiency was achieved, the rejection rate was reduced to 0.08% and zero WIP inventories in Line 1 became a practice. Lean tools brought significant changes in providing smooth process flow and productive operations, which in turn, give a remarkable contribution in achieving company’s goals, focus on the customers, giving quality products at the right time and at the right place. Therefore, the full implementation of BY Garments would contribute in gaining more profits.

  19. Manufacturing wizardry : products to tame heat, cold, deserts, swamps and underground infernos

    International Nuclear Information System (INIS)

    Jaremko, G.

    1997-01-01

    Some examples of Canadian oil and natural gas service equipment are cited as examples of exportable Canadian know-how. Foremosts are Canadian made, all terrain vehicles, designed to work in rugged terrain. Calgary-based Foremost Industries Inc., has sold several of their industrial vehicles for the Taklamakan, the high desert in the Tarim Basin of northwestern China. The huge vehicles with monster tires can haul up to 70 tonnes of material and leave very little or no mark on the wilderness. Foremost Industries Inc. is also an international corporation with branches in Nevada and Indiana. Their success stems from the fact that they were able to develop a vehicle for well drilling that would withstand the rough terrain and extreme climate conditions across western and northern Canada. Atco, a Calgary-based company, has developed quality portable housing to shelter surveyors, geologists, and drilling-rig crews. Another company, Reynolds Manufacturing, has developed safety clothing for workers in the oil industry. Canadian Oilfield Rigs and Equipment Fabrication Inc., manufacture volume production technology packages such as wireline data recording vehicles and well-service rigs, sold in markets from Algeria to Venezuela. 5 figs

  20. MODERN TECHNOLOGICAL SOLUTIONS USED IN THE PRODUCTION OF BAKERY PRODUCTS WITH HIGH BIOLOGICAL VALUE

    OpenAIRE

    Marta Brodowska; Dominika Guzek; Agnieszka Wierzbicka

    2014-01-01

    Biological value of the food products is a result of the presence of bioactive substances and the proportions of the components. Technological development allows to optimize and accelerate the processes of bread production and increase value of food. Bakery industry used whole grains and pseudocereals as additional source of active compounds, biotechnological techniques as using appropriate yeast strain and encapsulation, which provide protection of substance and their controlled release in p...

  1. Crop production in salt affected soils: A biological approach

    Energy Technology Data Exchange (ETDEWEB)

    Malik, K A [National Inst. for Biotechnology and Genetic Engineering (NIBGE), Faisalabad (Pakistan)

    1995-01-01

    Plant are susceptible to various stresses, affecting growth productivity. Among the abiotic stresses, soil salinity is most significant and prevalent in both developed and developing countries. As a result, good productive lands are being desertified at a very high pace. To combat this problem various approaches involving soil management and drainage are underway but with little success. It seems that a durable solution of the salinity and water-logging problems may take a long time and we may have to learn to live with salinity and to find other ways to utilize the affected lands fruitfully. A possible approach could be to tailor plants to suit the deleterious environment. The saline-sodic soils have excess of sodium, are impermeable, have little or no organic matter and are biologically almost dead. Introduction of a salt tolerant crop will provide a green cover and will improve the environment for biological activity, increase organic matter and will improve the soil fertility. The plant growth will result in higher carbon dioxide levels, and would thus create acidic conditions in the soil which would dissolve the insoluble calcium carbonate and will help exchange sodium with calcium ions on the soil complex. The biomass produced could be used directly as fodder or by the use of biotechnological and other procedures it could be converted into other value added products. However, in order to tailor plants to suit these deleterious environments, acquisition of better understanding of the biochemical and genetic aspects of salt tolerance at the cellular/molecular level is essential. For this purpose model systems have been carefully selected to carry out fundamental basic research that elucidates and identifies the major factors that confer salt tolerance in a living system. With the development of modern biotechnological methods it is now possible to introduce any foreign genetic material known to confer salt tolerance into crop plants. (Abstract Truncated)

  2. BIOMASS PRODUCTION AND FORMULATION OF Bacillus subtilis FOR BIOLOGICAL CONTROL

    Directory of Open Access Journals (Sweden)

    Amran Muis

    2016-10-01

    Full Text Available Bacillus subtilis is a widespread bacterium found in soil, water, and air. It controls the growth of certain harmful bacteria and fungi, presumably by competing for nutrients, growth sites on plants, and by directly colonizing and attaching to fungal pathogens. When applied to seeds, it colonizes the developing root system of the plants and continues to live on the root system and provides protection throughout the growing season. The study on biomass production and formulation of B. subtilis for biological control was conducted in the laboratory of Department of Plant Pathology, College of Agriculture, University of the Philippines Los Baños (UPLB-CA, College, Laguna from May to July 2005. The objective of the study was to determine the optimum pH and a good carbon source for biomass production of B. subtilis and to develop a seed treatment formulation of B. subtilis as biological control agent. Results showed that the optimum pH for growth of B. subtilis was pH 6 (1.85 x 109 cfu/ml. In laboratory tests for biomass production using cassava flour, corn flour, rice flour, and brown sugar as carbon sources, it grew best in brown sugar plus yeast extract medium (6.8 x 108 cfu ml-1 in sterile distilled water and 7.8 x 108 cfu ml-1 in coconut water. In test for bacterial biomass carriers, talc proved to be the best in terms of number of bacteria recovered from the seeds (3.98 x 105 cfu seed-1.

  3. Suitability of Gray Water for Hydroponic Crop Production Following Biological and Physical Chemical and Biological Subsystems

    Science.gov (United States)

    Bubenheim, David L.; Harper, Lynn D.; Wignarajah, Kanapathipillai; Greene, Catherine

    1994-01-01

    The water present in waste streams from a human habitat must be recycled in Controlled Ecological Life Support Systems (CELSS) to limit resupply needs and attain self-sufficiency. Plants play an important role in providing food, regenerating air, and producing purified water via transpiration. However, we have shown that the surfactants present in hygiene waste water have acute toxic effects on plant growth (Bubenheim et al. 1994; Greene et al., 1994). These phytotoxic affects can be mitigated by allowing the microbial population on the root surface to degrade the surfactant, however, a significant suppression (several days) in crop performance is experienced prior to reaching sub-toxic surfactant levels and plant recovery. An effective alternative is to stabilize the microbial population responsible for degradation of the surfactant on an aerobic bioreactor and process the waste water prior to utilization in the hydroponic solution (Wisniewski and Bubenheim, 1993). A sensitive bioassay indicates that the surfactant phytotoxicity is suppressed by more than 90% within 5 hours of introduction of the gray water to the bioreactor; processing for more than 12 hours degrades more than 99% of the phytotoxin. Vapor Compression Distillation (VCD) is a physical / chemical method for water purification which employees sequential distillation steps to separate water from solids and to volatilize contaminants. The solids from the waste water are concentrated in a brine and the pure product water (70 - 90% of the total waste water volume depending on operating conditions) retains non of the phytotoxic effects. Results of the bioassay were used to guide evaluations of the suitability of recovered gray water following biological and VCD processing for hydroponic lettuce production in controlled environments. Lettuce crops were grown for 28 days with 100% of the input water supplied with recovered water from the biological processor or VCD. When compared with the growth of plants

  4. Capacity optimization and scheduling of a multiproduct manufacturing facility for biotech products.

    Science.gov (United States)

    Shaik, Munawar A; Dhakre, Ankita; Rathore, Anurag S; Patil, Nitin

    2014-01-01

    A general mathematical framework has been proposed in this work for scheduling of a multiproduct and multipurpose facility involving manufacturing of biotech products. The specific problem involves several batch operations occurring in multiple units involving fixed processing time, unlimited storage policy, transition times, shared units, and deterministic and fixed data in the given time horizon. The different batch operations are modeled using state-task network representation. Two different mathematical formulations are proposed based on discrete- and continuous-time representations leading to a mixed-integer linear programming model which is solved using General Algebraic Modeling System software. A case study based on a real facility is presented to illustrate the potential and applicability of the proposed models. The continuous-time model required less number of events and has a smaller problem size compared to the discrete-time model. © 2014 American Institute of Chemical Engineers.

  5. Axiomatic design in large systems complex products, buildings and manufacturing systems

    CERN Document Server

    Suh, Nam

    2016-01-01

    This book provides a synthesis of recent developments in Axiomatic Design theory and its application in large complex systems. Introductory chapters provide concise tutorial materials for graduate students and new practitioners, presenting the fundamentals of Axiomatic Design and relating its key concepts to those of model-based systems engineering. A mathematical exposition of design axioms is also provided. The main body of the book, which represents a concentrated treatment of several applications, is divided into three parts covering work on: complex products; buildings; and manufacturing systems. The book shows how design work in these areas can benefit from the scientific and systematic underpinning provided by Axiomatic Design, and in so doing effectively combines the state of the art in design research with practice. All contributions were written by an international group of leading proponents of Axiomatic Design. The book concludes with a call to action motivating further research into the engineeri...

  6. Computer aided production of manufacturing CAMAC-wired boards by the multiwire-technique

    Energy Technology Data Exchange (ETDEWEB)

    Martini, M; Brehmer, W

    1975-10-01

    The multiwire-technique is a computer controlled wiring method for the manufacturing of circuit boards with insulated conductors. The technical data for production are dimensional drawings of the board and a list of all points which are to be connected. The listing must be in absolute co-ordinates including a list of all soldering points for component parts and a reproducible print pattern for inscription. For this wiring method a CAMAC standard board, a layout plan with alpha-numeric symbols, and a computer program which produces the essential technical data were developed. A description of the alpha-numeric symbols, the quality of the program, recognition and checking of these symbols, and the produced technical data is presented. (auth)

  7. Manufacturing technologies

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    The Manufacturing Technologies Center is an integral part of Sandia National Laboratories, a multiprogram engineering and science laboratory, operated for the Department of Energy (DOE) with major facilities at Albuquerque, New Mexico, and Livermore, California. Our Center is at the core of Sandia`s Advanced Manufacturing effort which spans the entire product realization process.

  8. Current problems of raw fish material processing while manufacturing dried products

    Directory of Open Access Journals (Sweden)

    Yashonkov A. A.

    2017-09-01

    Full Text Available The substantiation for using techniques of fish raw material canning has been presented, raw fish being caught or farmed in aquaculture. The main problems in raw fish canning have been reviewed, including significant reduction in thermolabile vitamins in the ultimate product as compared with the raw material due to the thermal processing. Promising canning technique – vacuum drying – has been proposed. This technique makes possible to reduce the temperature of thermal processing down to 50…55 °С and significantly enlarge preservation of thermolabile vitamins from the raw fish. Sampling of raw materials, semi-finished products, finished products, including preparation for analysis has been conducted by standard methods. Disadvantages of this way have been found, it is low energy efficiency of the process. The way to intensify the vacuum drying of aquatic organisms has been proposed based on the method of preliminary pore-forming due to augmenting the area of moisture evaporation. The design of the pilot plant has been proposed in order to research the process of pore forming and vacuum drying. Target species for processing have been suggested. They are as follows: Azov goby (fillet for food products and Black Sea sprat for feeds. The recipes of the feed mixture for granulated floating food for trout have been developed. The results of the first series of the pilot research have been provided. The experiments have proved that preliminary pore forming immediately before vacuum drying makes possible to enlarge the surface area of moisture evaporation by 15…25 %. By processing photomicrographs of sections by means of a special software the authors have got the results demonstrating that when manufacturing dried products by pore forming and drying under pressure 10 kPa the pore take 35...38 % of the inner volume of the product and with drying under pressure 10 kPa – only 18...21 %, and when drying under the atmospheric pressure – 11...13 %.

  9. Industrial production and professional application of manufactured nanomaterials-enabled end products in Dutch industries: potential for exposure.

    Science.gov (United States)

    Bekker, Cindy; Brouwer, Derk H; Tielemans, Erik; Pronk, Anjoeka

    2013-04-01

    In order to make full use of the opportunities while responsibly managing the risks of working with manufactured nanomaterials (MNM), we need to gain insight into the potential level of exposure to MNM in the industry. Therefore, the goal of this study was to obtain an overview of the potential MNM exposure scenarios within relevant industrial sectors, applied exposure controls, and number of workers potentially exposed to MNM in Dutch industrial sectors producing and applying MNM-enabled end products in the Netherlands. A survey was conducted in three phases: (i) identification of MNM-enabled end products; (ii) identification of relevant industrial sectors; and (iii) a tiered telephone survey to estimate actual use of the products among 40 sector organizations/knowledge centres (Tier 1), 350 randomly selected companies (Tier 2), and 110 actively searched companies (Tier 3). The most dominant industrial sectors producing or applying MNM-enabled end products (market penetration >5%) are shoe repair shops, automotive, construction, paint, metal, and textile cleaning industry. In the majority of the companies (76%), potential risks related to working with MNM are not a specific point of interest. The total number of workers potentially exposed to MNM during the production or application of MNM-enabled end products was estimated at approximately 3000 workers in the Netherlands. The results of this study will serve as a basis for in-depth exposure and health surveys that are currently planned in the Netherlands. In addition, the results can be used to identify the most relevant sectors for policy makers and future studies focussing on evaluating the risks of occupational exposure to MNM.

  10. Review of production status of heavy steel castings and key technologies for their manufacture in China

    Directory of Open Access Journals (Sweden)

    Liu Baicheng

    2008-02-01

    Full Text Available This paper expatiates on domestic status of heavy steel casting production, with a special focus on hydraulic turbine castings for Three Gorges Project. In China, there is magnificent demand for heavy castings with the rapid growth of the national economy in recent years and the expected high growth in the coming 10 to 20 years. Some heavy and large castings such as mill housing and hydraulic turbine runner crown, blade and band for Three Gorges Project have been successfully made. However, the domestic production capability is still far from meeting the gigantic requirements. The domestic capability still lags behind the world class level, and a lot of heavy castings still depend on import. The paper also gives a particular introduction of the key technologies in the manufacturing of heavy steel castings like metal melting, foundry technology, heat treatment technology and numerical simulation technique, etc. In addition, several case studies on the application of numerical simulation in the production of heavy steel castings are presented.

  11. Continuous fermentative hydrogen production from coffee drink manufacturing wastewater by applying UASB reactor

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Kyung-Won; Shin, Hang-Sik [Department of Civil and Environmental Engineering, KAIST, 373-1 Guseong-dong, Yuseong-gu, Daejeon 305-701 (Korea, Republic of); Kim, Dong-Hoon [Department of Civil and Environmental Engineering, University of Windsor, 401 Sunset Ave., Essex Hall, Windsor, Ontario (Canada)

    2010-12-15

    The feasibility of continuous H{sub 2} production from coffee drink manufacturing wastewater (CDMW) was tested in two different types of reactors: a completely-stirred tank reactor (CSTR) and an up-flow anaerobic sludge blanket reactor (UASBr). While the performance in CSTR was limited, it was significantly enhanced in UASBr. The maximum H{sub 2} yield of 1.29 mol H{sub 2}/mol hexose{sub added} was achieved at HRT of 6 h in UASBr operation. Non-hydrogenic, lactic acid was the dominant in CSTR, while butyric and caproic acids in UASBr. As caproic acid is generated by consuming acetic and butyric acids, all of which are related to H{sub 2} production, the presence of caproic acid in the broth also indicates H{sub 2} production, yielding 1.33 mol H{sub 2}/glucose. It was speculated that the enhanced performance in UASBr was attributed to the high concentration of biomass over 60,000 mg VSS/L in the blanket zone, which provided insufficient substrate for indigenous lactic acid bacteria (LAB) to survive. The abundance of LAB in CDMW was confirmed by natural fermentation of CDMW. That is without the addition of external inoculum, CDMW was mainly fermented into lactic acid under mesophilic condition. For the first time ever, H{sub 2} producing granules (HPG) with diameters of 2.1 mm were successfully formed by using actual waste as a substrate. (author)

  12. Evaluation of hardboard manufacturing process wastewater as a feedstream for ethanol production.

    Science.gov (United States)

    Groves, Stephanie; Liu, Jifei; Shonnard, David; Bagley, Susan

    2013-07-01

    Waste streams from the wood processing industry can serve as feedstream for ethanol production from biomass residues. Hardboard manufacturing process wastewater (HPW) was evaluated on the basis of monomeric sugar recovery and fermentability as a novel feedstream for ethanol production. Dilute acid hydrolysis, coupled with concentration of the wastewater resulted in a hydrolysate with 66 g/l total fermentable sugars. As xylose accounted for 53 % of the total sugars, native xylose-fermenting yeasts were evaluated for their ability to produce ethanol from the hydrolysate. The strains selected were, in decreasing order by ethanol yields from xylose (Y p/s, based on consumed sugars), Scheffersomyces stipitis ATCC 58785 (CBS 6054), Pachysolen tannophilus ATCC 60393, and Kluyveromyces marxianus ATCC 46537. The yeasts were compared on the basis of substrate utilization and ethanol yield during fermentations of the hydrolysate, measured using an HPLC. S. stipitis, P. tannophilus, and K. marxianus produced 0.34, 0.31, and 0.36 g/g, respectively. The yeasts were able to utilize between 58 and 75 % of the available substrate. S. stipitis outperformed the other yeast during the fermentation of the hydrolysate; consuming the highest concentration of available substrate and producing the highest ethanol concentration in 72 h. Due to its high sugar content and low inhibitor levels after hydrolysis, it was concluded that HPW is a suitable feedstream for ethanol production by S. stipitis.

  13. Lean Manufacturing Implementation for Multinational Companies with Production Subsidiary in Brazil: Development of A Roadmap

    Directory of Open Access Journals (Sweden)

    L. Goehnera,

    2016-06-01

    Full Text Available Foreign multinational companies with a production subsidiary in Brazil are in general recognized as high-level productive companies; however, their productivity potential is mostly not fully achieved. Lean Manufacturing (LM has been proved as a valuable aid to achieve competitiveness in the long run. Regarding the rising importance of successfully implementing LM at multinationals in Brazil and an apparent lack of discussion regarding LM in Brazil this paper aims to propose a comprehensive implementation roadmap, which enables a multinational on a basis of a systematic approach, to achieve an advanced sustainable LM system in a practical manner. The insights of literature and case studies are combined to develop the roadmap. The roadmap was developed so that both companies, those, which have not started yet their journey towards LM, as well as those that have taken already the first steps can use the roadmap. However, the roadmap was built on a broad empirical basis. It should be noticed that it is impossible to consider all factors influencing the LMI at multinationals operating in Brazil in a real world setting. As a result, the roadmap should not be regarded as a ready implementation plan, which has to be strictly followed. Instead, it should be seen as a guideline, which helps a multinational to develop its own, detailed and fitted plan for successfully implementing LM and establishing a learning organization.

  14. Using Goat's Milk, Barley Flour, Honey, and Probiotic to Manufacture of Functional Dairy Product.

    Science.gov (United States)

    Ismail, Magdy Mohamed; Hamad, Mohamed Farid; Elraghy, Esraa Mohamed

    2017-08-23

    Stirred yogurt manufactured using probiotic culture which usually called Rayeb milk in the Middle East region is one of the most important functional fermented milk products. To increase the health and functionality properties to this product, some ingredients like fruits, cereal, and whey protein are used in production. This study was carried out to prepare functional Rayeb milk from goat's milk, barley flour (15%) and honey (4%) mixtures using ABT culture. Also, vanilla and cocoa powder were used as flavorings. Adding barley flour and honey to goat's milk increased curd tension and water-holding capacity and decreased coagulation time and susceptibility to syneresis. The values of carbohydrate, total solids, dietary fiber, ash, total protein, water soluble nitrogen, total volatile fatty acids, unsaturated fatty acids, oleic, linoleic, α-linolenic acids, and antioxidant activity were higher in Rayeb milk supplemented with barley flour and honey than control. The viabilities of Lactobacillus acidophilus and Bifidobacterium lactis Bb12 (Chr. Hansen's Lab A/S) increased in fortified Rayeb milk. The recommended level of 10 7  cfu g -1 of bifidobacteria as a probiotic was exceeded for these samples. Addition of vanilla (0.1%) or cocoa powder (0.5%) improved the sensory properties of fortified Rayeb milk.

  15. Production and biological activities of yellow pigments from Monascus fungi.

    Science.gov (United States)

    Chen, Gong; Wu, Zhenqiang

    2016-08-01

    Monascus yellow pigments (MYPs), are azaphilone compounds and one of the three main components of total Monascus pigments (MPs). Thirty-five hydrophilic or hydrophobic MYPs have been identified, with the majority being hydrophobic. Apart from screening special Monascus strains, some advanced approaches, such as extractive and high-cell-density fermentations, have been applied for developing or producing new MYPs, especially extracellular hydrophilic MYPs. The outstanding performance of MYPs in terms of resistance to photodegradation, as well as tolerance for temperature and pH, give natural MYPs reasonable prospects, compared with the orange and red MPs, for practical use in the present and future. Meanwhile, MYPs have shown promising potential for applications in the food and pharmaceutical industries based on their described bioactivities. This review briefly summarizes the reports to date on chemical structures, biological activities, biosynthetic pathways, production technologies, and physicochemical performances of MYPs. The existing problems for MYPs are discussed and research prospects proposed.

  16. MODERN TECHNOLOGICAL SOLUTIONS USED IN THE PRODUCTION OF BAKERY PRODUCTS WITH HIGH BIOLOGICAL VALUE

    Directory of Open Access Journals (Sweden)

    Marta Brodowska

    2014-06-01

    Full Text Available Biological value of the food products is a result of the presence of bioactive substances and the proportions of the components. Technological development allows to optimize and accelerate the processes of bread production and increase value of food. Bakery industry used whole grains and pseudocereals as additional source of active compounds, biotechnological techniques as using appropriate yeast strain and encapsulation, which provide protection of substance and their controlled release in production of functional bread. The adding to bread fruits, vegetables and condiments may increase content of vitamin, minerals, dietary fiber and other bioactive compounds.

  17. Standardization of Good Manufacturing Practice-compliant production of bone marrow-derived human mesenchymal stromal cells for immunotherapeutic applications.

    Science.gov (United States)

    Wuchter, Patrick; Bieback, Karen; Schrezenmeier, Hubert; Bornhäuser, Martin; Müller, Lutz P; Bönig, Halvard; Wagner, Wolfgang; Meisel, Roland; Pavel, Petra; Tonn, Torsten; Lang, Peter; Müller, Ingo; Renner, Matthias; Malcherek, Georg; Saffrich, Rainer; Buss, Eike C; Horn, Patrick; Rojewski, Markus; Schmitt, Anita; Ho, Anthony D; Sanzenbacher, Ralf; Schmitt, Michael

    2015-02-01

    Human mesenchymal stem or stromal cells (MSCs) represent a potential resource not only for regenerative medicine but also for immunomodulatory cell therapies. The application of different MSC culture protocols has significantly hampered the comparability of experimental and clinical data from different laboratories and has posed a major obstacle for multicenter clinical trials. Manufacturing of cell products for clinical application in the European Community must be conducted in compliance with Good Manufacturing Practice and requires a manufacturing license. In Germany, the Paul-Ehrlich-Institut as the Federal Authority for Vaccines and Biomedicines is critically involved in the approval process. This report summarizes a consensus meeting between researchers, clinicians and regulatory experts on standard quality requirements for MSC production. The strategy for quality control testing depends on the product's cell composition, the manufacturing process and the indication and target patient population. Important quality criteria in this sense are, among others, the immunophenotype of the cells, composition of the culture medium and the risk for malignant transformation, as well as aging and the immunosuppressive potential of the manufactured MSCs. This position paper intends to provide relevant information to interested parties regarding these criteria to foster the development of scientifically valid and harmonized quality standards and to support approval of MSC-based investigational medicinal products. Copyright © 2015 International Society for Cellular Therapy. Published by Elsevier Inc. All rights reserved.

  18. Cloud-based design and manufacturing (CBDM) a service-oriented product development paradigm for the 21st century

    CERN Document Server

    2014-01-01

    The book introduces the reader to game-changing ways of building and utilizing Internet-based services related to design and manufacture activities through the cloud. In a broader sense, CBDM refers to a new product realization model that enables collective open innovation and rapid product development with minimum costs through social networking and negotiation platforms between service providers and consumers. It is a type of parallel and distributed system consisting of a collection of inter-connected physical and virtualized service pools of design and manufacturing resources as well as intelligent search capabilities for design and manufacturing solutions. Practicing engineers and decision makers will learn how to strategically position their product development operations for success in a globalized interconnected world.

  19. Smart Manufacturing.

    Science.gov (United States)

    Davis, Jim; Edgar, Thomas; Graybill, Robert; Korambath, Prakashan; Schott, Brian; Swink, Denise; Wang, Jianwu; Wetzel, Jim

    2015-01-01

    Historic manufacturing enterprises based on vertically optimized companies, practices, market share, and competitiveness are giving way to enterprises that are responsive across an entire value chain to demand dynamic markets and customized product value adds; increased expectations for environmental sustainability, reduced energy usage, and zero incidents; and faster technology and product adoption. Agile innovation and manufacturing combined with radically increased productivity become engines for competitiveness and reinvestment, not simply for decreased cost. A focus on agility, productivity, energy, and environmental sustainability produces opportunities that are far beyond reducing market volatility. Agility directly impacts innovation, time-to-market, and faster, broader exploration of the trade space. These changes, the forces driving them, and new network-based information technologies offering unprecedented insights and analysis are motivating the advent of smart manufacturing and new information technology infrastructure for manufacturing.

  20. Concerning of Defects in Design and Manufacture of the Products. Case Study: Redesign of the Citrus Juicer

    Directory of Open Access Journals (Sweden)

    Bogdan BUCUR

    2015-12-01

    Full Text Available Industrial products market is marked by a series of mistakes resulting from their design and manufacture. These defects are due to a superficial conceptual analysis, with emphasis on manufacturing to lower cost price, without a few aspects like: functional, ergonomic, aesthetic and cultural in product development. This analysis is important because it combines all these aspects and which aim the final solution of the optimized product. This paper proposes a method of study that identifies those aspects of the analysis of a product on the market that is a citrus juicer. Redesigning the product is made using AutoCAD and Inventor Autodesk design environment. The method proposed in this paper it will be applied to any industrial product, respecting their particularities.

  1. Recombinant biologic products versus nutraceuticals from plants – a regulatory choice?

    Science.gov (United States)

    Drake, Pascal M. W.; Szeto, Tim H.; Paul, Mathew J.; Teh, Audrey Y.‐H.

    2016-01-01

    Biotechnology has transformed the potential for plants to be a manufacturing source of pharmaceutical compounds. Now, with transgenic and transient expression techniques, virtually any biologic, including vaccines and therapeutics, could be manufactured in plants. However, uncertainty over the regulatory path for such new pharmaceuticals has been a deterrent. Consideration has been given to using alternative regulatory paths, including those for nutraceuticals or cosmetic agents. This review will consider these possibilities, and discuss the difficulties in establishing regulatory guidelines for new pharmaceutical manufacturing technologies. PMID:27297459

  2. Biological evaluation of nanosilver incorporated cellulose pulp for hygiene products

    Energy Technology Data Exchange (ETDEWEB)

    Kavitha Sankar, P.C.; Ramakrishnan, Reshmi; Rosemary, M.J., E-mail: rosemarymj@lifecarehll.com

    2016-04-01

    Cellulose pulp has a visible market share in personal hygiene products such as sanitary napkins and baby diapers. However it offers good surface for growth of microorganisms. Huge amount of research is going on in developing hygiene products that do not initiate microbial growth. The objective of the present work is to produce antibacterial cellulose pulp by depositing silver nanopowder on the cellulose fiber. The silver nanoparticles used were of less than 100 nm in size and were characterised using transmission electron microscopy and X-ray powder diffraction studies. Antibacterial activity of the functionalized cellulose pulp was proved by JIS L 1902 method. The in-vitro cytotoxicity, in-vivo vaginal irritation and intracutaneous reactivity studies were done with silver nanopowder incorporated cellulose pulp for introducing a new value added product to the market. Cytotoxicity evaluation suggested that the silver nanoparticle incorporated cellulose pulp is non-cytotoxic. No irritation and skin sensitization were identified in animals tested with specific extracts prepared from the test material in the in-vivo experiments. The results indicated that the silver nanopowder incorporated cellulose pulp meets the requirements of the standard practices recommended for evaluating the biological reactivity and has good biocompatibility, hence can be classified as a safe hygiene product. - Highlights: • Different amounts of silver nanoparticles (0.2 g–0.4 g/napkin) were added to cellulose pulp. • The silver nanoparticle incorporated cellulose pulp was proved to be antibacterial by JIS L 1902 method. • The minimum concentration of silver required for antibacterial activity with no cytotoxicity has been found out. • In-vivo vaginal irritation and intracutaneous reactivity studies confirmed the biocompatibility of the material.

  3. Biological evaluation of nanosilver incorporated cellulose pulp for hygiene products

    International Nuclear Information System (INIS)

    Kavitha Sankar, P.C.; Ramakrishnan, Reshmi; Rosemary, M.J.

    2016-01-01

    Cellulose pulp has a visible market share in personal hygiene products such as sanitary napkins and baby diapers. However it offers good surface for growth of microorganisms. Huge amount of research is going on in developing hygiene products that do not initiate microbial growth. The objective of the present work is to produce antibacterial cellulose pulp by depositing silver nanopowder on the cellulose fiber. The silver nanoparticles used were of less than 100 nm in size and were characterised using transmission electron microscopy and X-ray powder diffraction studies. Antibacterial activity of the functionalized cellulose pulp was proved by JIS L 1902 method. The in-vitro cytotoxicity, in-vivo vaginal irritation and intracutaneous reactivity studies were done with silver nanopowder incorporated cellulose pulp for introducing a new value added product to the market. Cytotoxicity evaluation suggested that the silver nanoparticle incorporated cellulose pulp is non-cytotoxic. No irritation and skin sensitization were identified in animals tested with specific extracts prepared from the test material in the in-vivo experiments. The results indicated that the silver nanopowder incorporated cellulose pulp meets the requirements of the standard practices recommended for evaluating the biological reactivity and has good biocompatibility, hence can be classified as a safe hygiene product. - Highlights: • Different amounts of silver nanoparticles (0.2 g–0.4 g/napkin) were added to cellulose pulp. • The silver nanoparticle incorporated cellulose pulp was proved to be antibacterial by JIS L 1902 method. • The minimum concentration of silver required for antibacterial activity with no cytotoxicity has been found out. • In-vivo vaginal irritation and intracutaneous reactivity studies confirmed the biocompatibility of the material.

  4. Production of fiberglass/metal composite material suitable for building habitat and manufacturing facilities

    Science.gov (United States)

    1987-01-01

    The production of a fiberglass/metal composite material suitable for building habitats and manufacturing facilities was the project for Clemson. The concept and development of the knowledge necessary to produce glass fibers originated in the spring semester. During the summer, while at Johnson Space Center, fiberglass from a rock composition similar to ones found at the Apollo 16 site on the moon was successfully produced. The project this year was a continuation of last year's studies. We addressed the following problems which emerged as the work progressed: (1) Methods for coating the fibers with a metal were explored. We manufactured composites in two stages: Glass fibers without any coating on them; and fibers coated with metals as they were made. This proved to be a difficult process. Future activities include using a chemical vapor deposition process on fibers which have been made. (2) A glass furnace was developed which relies primarily on solar energy for melting the glass. The temperature of the melted glass is maintained by electrical means. The design is for 250 kg of glass per day. An electrical engineering student developed a scheme for controlling the melting and manufacturing process from the earth. This was done to minimize the human risk. Graphite refractories are relied on to contain the melt. (3) The glass composition chosen for the project is a relatively pure anorthite which is available in the highland regions of the lunar surface. A major problems with this material is that it melts at a comparatively high temperature. This problem will be solved by using graphite refractory materials for the furnace. The advantage of this glass composition is that it is very stable and does not tend to crystallize. (4) We have also refined the experimental furnace and fiber making machinery which we will be using at Johnson Space Center this summer. We believe that we will be able to draw and coat glass fibers in a vacuum for use in composites. We intend to

  5. Hormones in international meat production: biological, sociological and consumer issues.

    Science.gov (United States)

    Galbraith, Hugh

    2002-12-01

    Beef and its products are an important source of nutrition in many human societies. Methods of production vary and include the use of hormonal compounds ('hormones') to increase growth and lean tissue with reduced fat deposition in cattle. The hormonal compounds are naturally occurring in animals or are synthetically produced xenobiotics and have oestrogenic (oestradiol-17beta and its esters; zeranol), androgenic (testosterone and esters; trenbolone acetate) or progestogenic (progesterone; melengestrol acetate) activity. The use of hormones as production aids is permitted in North American countries but is no longer allowed in the European Union (EU), which also prohibits the importation of beef and its products derived from hormone-treated cattle. These actions have resulted in a trade dispute between the two trading blocs. The major concern for EU authorities is the possibility of adverse effects on human consumers of residues of hormones and metabolites. Methods used to assess possible adverse effects are typical of those used by international agencies to assess acceptability of chemicals in human food. These include analysis of quantities present in the context of known biological activity and digestive, absorptive, post-absorptive and excretory processes. Particular considerations include the low quantities of hormonal compounds consumed in meat products and their relationships to endogenous production particularly in prepubertal children, enterohepatic inactivation, cellular receptor- and non-receptor-mediated effects and potential for interference with growth, development and physiological function in consumers. There is particular concern about the role of oestradiol-17beta as a carcinogen in certain tissues. Now subject to a 'permanent' EU ban, current evidence suggests that certain catechol metabolites may induce free-radical damage of DNA in cell and laboratory animal test systems. Classical oestrogen-receptor mediation is considered to stimulate

  6. Power infrastructure quality and manufacturing productivity in Africa: A firm level analysis

    International Nuclear Information System (INIS)

    Moyo, Busani

    2013-01-01

    This study sought to examine the impact of the quality of power infrastructure on productivity in African manufacturing firms using data from the World Bank enterprise surveys. We measured power infrastructure quality using the number of hours per day without electricity and the percentage of output lost due to outages and found these indicators to be negative and significant determinants of productivity. These variables seem to be significant determinants in Uganda, Tanzania and Zambia as well as in the food and agriculture sector. To improve economic growth and encourage employment creation, governments in Africa have to come up with measures to improve the reliability of electricity infrastructure. - Highlights: • Power infrastructure quality indicators are found to have a negative and significant effect. • The power quality indicators have varied effects both at country and sector level. • Owning a generator minimises the negative impact of outages in Uganda, Tanzania and Mauritius. • Other controls like labour, capital, foreign ownership etc. have a positive and significant effect. • The firm age variable is insignificant suggesting that accumulated knowledge does not matter

  7. Antimicrobial activity of thin metallic silver flakes, waste products of a manufacturing process.

    Science.gov (United States)

    Anzano, Manuela; Tosti, Alessandra; Lasagni, Marina; Campiglio, Alfredo; Pitea, Demetrio; Collina, Elena

    2011-01-01

    The aim of the research was to develop new products and processes from a manufacturing waste from an Italian metallurgic company. The company produced thin silver metallic films and the production scraps were silver flakes. The possibility to use the silver flakes in water disinfection processes was studied. The antimicrobial activity of the flakes was investigated in batch using Escherichia coli as Gram-negative microorganism model. The flakes did not show any antimicrobial activity, so they were activated with two different processes: thermal activation in reducing atmosphere and chemical activation, obtaining, respectively, reduced flakes (RF) and chemical flakes (CF). The flakes, activated with either treatment, showed antimicrobial activity against E. coli. The kill rate was dependent on the type of activated flakes. The chemical flakes were more efficient than reduced flakes. The kill rate determined for 1 g of CF, 1.0 +/- 0.2 min(-1), was greater than the kill rate determined for 1 g of RF, 0.069 +/- 0.004 min(-1). This was confirmed also by the minimum inhibitory concentration values. It was demonstrated that the antimicrobial capability was dependent on flakes amount and on the type of aqueous medium. Furthermore, the flakes maintained their properties also when used a second time. Finally, the antimicrobial activities of flakes were tested in an effluent of a wastewater treatment plant where a variety of heterotrophic bacteria were present.

  8. Animal use in the chemical and product manufacturing sectors - can the downtrend continue?

    Science.gov (United States)

    Curren, Rodger

    2009-12-01

    During the 1990s and early 2000s, a number of manufacturing companies in the cosmetic, personal care and household product industries were able to substantially reduce their use of animals for testing (or to not use animals in the first place). These reductions were almost always the result of significant financial contributions to either direct, in-house alternatives research, or to support personnel whose duties were to understand and apply the current state-of-the-art for in vitro testing. They occurred almost exclusively in non-regulatory areas, and primarily involved acute topical toxicities. Over the last few years, the reduction in animal use has been much less dramatic, because some companies are still reluctant to change from the traditional animal studies, because systemic, repeat-dose toxicity is more difficult to model in vitro, and because many products still require animal testing for regulatory approval. Encouragingly, we are now observing an increased acceptance of non-animal methods by regulatory agencies. This is due to mounting scientific evidence from larger databases, agreement by companies to share data and testing strategies with regulatory agencies, and a focus on smaller domains of applicability. These changes, along with new emphasis and financial support for addressing systemic toxicities, promise to provide additional possibilities for industry to replace animals with in vitro methods, alone or in combination with in silico methods. However, the largest advance will not occur until more companies commit to using the non-animal test strategies that are currently available. 2009 FRAME.

  9. Design for Manufacture and Assembly for Product Development (Case study : Emergency Lamp)

    Science.gov (United States)

    Ngatilah, Y.; Pulansari, F.; Ernawati, Dira; Pujiastuti, C.; Parwati, C. I.; Prasetyo, B.

    2018-01-01

    Community needs that are not primary but important in everyday life are lights for lighting. State electricity company (PLN) is experiencing limitations in supplying electricity for this puIDRose. Therefore emergency lights (emergency lights) are already marketed in the community, which limited function only illuminate a very limited space. Therefore we developed the design of energy saving lamps using “Light Emitting Diode” (LED) which can illuminate the whole house as well as functioning as mobile phone charger (HP). The method used is Design for Manufacture and Assembly (DFMA), with the result of design development The percentage increase in assembly efficiency (E) is 0.01071 - 0.00645 = 0.00426 or = 39.76%. The decrease in material costs is IDR 234,000 - IDR 214,000 = IDR 20,000 or = 8.54% .Development design is received because of more assembly efficiency than the initial design. Power usage on previous products with series and designs of the original product can last only 4-5 hours non-stop, while the development of the design can survive 9-10 hours 2x more energy efficient.

  10. Biological risks associated with consumption of reptile products.

    Science.gov (United States)

    Magnino, Simone; Colin, Pierre; Dei-Cas, Eduardo; Madsen, Mogens; McLauchlin, Jim; Nöckler, Karsten; Maradona, Miguel Prieto; Tsigarida, Eirini; Vanopdenbosch, Emmanuel; Van Peteghem, Carlos

    2009-09-15

    The consumption of a wide variety of species of reptiles caught from the wild has been an important source of protein for humans world-wide for millennia. Terrapins, snakes, lizards, crocodiles and iguanas are now farmed and the consumption and trade of their meat and other edible products have recently increased in some areas of the world. Biological risks associated with the consumption of products from both farmed and wild reptile meat and eggs include infections caused by bacteria (Salmonella spp., Vibrio spp.), parasites (Spirometra, Trichinella, Gnathostoma, pentastomids), as well as intoxications by biotoxins. For crocodiles, Salmonella spp. constitute a significant public health risk due to the high intestinal carrier rate which is reflected in an equally high contamination rate in their fresh and frozen meat. There is a lack of information about the presence of Salmonella spp. in meat from other edible reptilians, though captive reptiles used as pets (lizards or turtles) are frequently carriers of these bacteria in Europe. Parasitic protozoa in reptiles represent a negligible risk for public health compared to parasitic metazoans, of which trichinellosis, pentastomiasis, gnathostomiasis and sparganosis can be acquired through consumption of contaminated crocodile, monitor lizard, turtle and snake meat, respectively. Other reptiles, although found to harbour the above parasites, have not been implicated with their transmission to humans. Freezing treatment inactivates Spirometra and Trichinella in crocodile meat, while the effectiveness of freezing of other reptilian meat is unknown. Biotoxins that accumulate in the flesh of sea turtles may cause chelonitoxism, a type of food poisoning with a high mortality rate in humans. Infections by fungi, including yeasts, and viruses widely occur in reptiles but have not been linked to a human health risk through the contamination of their meat. Currently there are no indications that natural transmissible spongiform

  11. Greenhouse gas emissions from production chain of a cigarette manufacturing industry in Pakistan

    International Nuclear Information System (INIS)

    Hussain, Majid; Zaidi, Syed Mujtaba Hasnian; Malik, Riffat Naseem; Sharma, Benktesh Dash

    2014-01-01

    This study quantified greenhouse gas (GHG) emissions from the Pakistan Tobacco Company (PTC) production using a life cycle approach. The PTC production chain comprises of two phases: agricultural activities (Phase I) and industrial activities (Phase II). Data related to agricultural and industrial activities of PTC production chain were collected through questionnaire survey from tobacco growers and records from PTC manufacturing units. The results showed that total GHG emissions from PTC production chain were 44,965, 42,875, and 43,839 tCO 2 e respectively in 2009, 2010, and 2011. Among the agricultural activities, firewood burning for tobacco curing accounted for about 3117, 3565, and 3264 tCO 2 e, fertilizer application accounted for 754, 3251, and 4761 tCO 2 e in 2009, 2010, and 2011, respectively. Among the industrial activities, fossil fuels consumption in stationary sources accounted for 15,582, 12,733, and 13,203 tCO 2 e, fossil fuels used in mobile sources contributed to 2693, 3038, and 3260 tCO 2 e, and purchased electricity consumed resulted in 15,177, 13,556, and 11,380 tCO 2 e in 2009, 2010, and 2011, respectively. The GHG emissions related to the transportation of raw materials and processed tobacco amounted to 6800, 6301, and 7317 respectively in 2009, 2010, and 2011. GHG emissions from energy use in the industrial activities constituted the largest emissions (i.e., over 80%) of GHG emissions as PTC relies on fossil fuels and fossil fuel based electrical power in industrial processes. The total emissions of carbon footprint (CFP) from PTC production were 0.647 tCO 2 e per million cigarettes produced in 2009, 0.675 tCO 2 e per million cigarettes in 2010 and 0.59 tCO 2 e per million cigarettes in 2011. Potential strategies for GHG emissions reductions for PTC production chain include energy efficiency, reducing reliance on fossil fuels in non-mobile sources, adoption of renewable fuels including solar energy, energy from crop residues, and promotion of

  12. Greenhouse gas emissions from production chain of a cigarette manufacturing industry in Pakistan

    Energy Technology Data Exchange (ETDEWEB)

    Hussain, Majid, E-mail: majid_qau86@yahoo.com [Environmental Biology and Ecotoxicology Laboratory, Department of Environmental Sciences, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Department of Forestry and Wildlife Management, University of Haripur, Hattar Road, Khyber Pakhtunkhwa, Haripur 22620 (Pakistan); Zaidi, Syed Mujtaba Hasnian [Leaf Agronomy Manager, Pakistan Tobacco Company, Akora Khattak Factory, P.O. and District Nowshera, Khyber Pakhtunkhwa (Pakistan); Malik, Riffat Naseem, E-mail: r_n_malik2000@yahoo.co.uk [Environmental Biology and Ecotoxicology Laboratory, Department of Environmental Sciences, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Sharma, Benktesh Dash [University of California, Berkeley, California 94720 (United States)

    2014-10-15

    This study quantified greenhouse gas (GHG) emissions from the Pakistan Tobacco Company (PTC) production using a life cycle approach. The PTC production chain comprises of two phases: agricultural activities (Phase I) and industrial activities (Phase II). Data related to agricultural and industrial activities of PTC production chain were collected through questionnaire survey from tobacco growers and records from PTC manufacturing units. The results showed that total GHG emissions from PTC production chain were 44,965, 42,875, and 43,839 tCO{sub 2}e respectively in 2009, 2010, and 2011. Among the agricultural activities, firewood burning for tobacco curing accounted for about 3117, 3565, and 3264 tCO{sub 2}e, fertilizer application accounted for 754, 3251, and 4761 tCO{sub 2}e in 2009, 2010, and 2011, respectively. Among the industrial activities, fossil fuels consumption in stationary sources accounted for 15,582, 12,733, and 13,203 tCO{sub 2}e, fossil fuels used in mobile sources contributed to 2693, 3038, and 3260 tCO{sub 2}e, and purchased electricity consumed resulted in 15,177, 13,556, and 11,380 tCO{sub 2}e in 2009, 2010, and 2011, respectively. The GHG emissions related to the transportation of raw materials and processed tobacco amounted to 6800, 6301, and 7317 respectively in 2009, 2010, and 2011. GHG emissions from energy use in the industrial activities constituted the largest emissions (i.e., over 80%) of GHG emissions as PTC relies on fossil fuels and fossil fuel based electrical power in industrial processes. The total emissions of carbon footprint (CFP) from PTC production were 0.647 tCO{sub 2}e per million cigarettes produced in 2009, 0.675 tCO{sub 2}e per million cigarettes in 2010 and 0.59 tCO{sub 2}e per million cigarettes in 2011. Potential strategies for GHG emissions reductions for PTC production chain include energy efficiency, reducing reliance on fossil fuels in non-mobile sources, adoption of renewable fuels including solar energy, energy

  13. 78 FR 19492 - Draft Guidance for Industry on Formal Meetings Between FDA and Biosimilar Biological Product...

    Science.gov (United States)

    2013-04-01

    ..., or Office of Communication, Outreach, and Development (HFM-40), Center for Biologics Evaluation and... biological product. This draft guidance describes the Agency's current thinking on how it intends to... review of biosimilar biological products. Because these meetings often will represent critical points in...

  14. 78 FR 20663 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2013-04-05

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug... public. Name of Committee: Vaccines and Related Biological Products Advisory Committee. General Function..., Office of Vaccines Research and Review, Center for Biologics Evaluation and Research, FDA. FDA intends to...

  15. Sustainable production of biologically active molecules of marine based origin.

    Science.gov (United States)

    Murray, Patrick M; Moane, Siobhan; Collins, Catherine; Beletskaya, Tanya; Thomas, Olivier P; Duarte, Alysson W F; Nobre, Fernando S; Owoyemi, Ifeloju O; Pagnocca, Fernando C; Sette, L D; McHugh, Edward; Causse, Eric; Pérez-López, Paula; Feijoo, Gumersindo; Moreira, Ma T; Rubiolo, Juan; Leirós, Marta; Botana, Luis M; Pinteus, Susete; Alves, Celso; Horta, André; Pedrosa, Rui; Jeffryes, Clayton; Agathos, Spiros N; Allewaert, Celine; Verween, Annick; Vyverman, Wim; Laptev, Ivan; Sineoky, Sergei; Bisio, Angela; Manconi, Renata; Ledda, Fabio; Marchi, Mario; Pronzato, Roberto; Walsh, Daniel J

    2013-09-25

    The marine environment offers both economic and scientific potential which are relatively untapped from a biotechnological point of view. These environments whilst harsh are ironically fragile and dependent on a harmonious life form balance. Exploitation of natural resources by exhaustive wild harvesting has obvious negative environmental consequences. From a European industry perspective marine organisms are a largely underutilised resource. This is not due to lack of interest but due to a lack of choice the industry faces for cost competitive, sustainable and environmentally conscientious product alternatives. Knowledge of the biotechnological potential of marine organisms together with the development of sustainable systems for their cultivation, processing and utilisation are essential. In 2010, the European Commission recognised this need and funded a collaborative RTD/SME project under the Framework 7-Knowledge Based Bio-Economy (KBBE) Theme 2 Programme 'Sustainable culture of marine microorganisms, algae and/or invertebrates for high value added products'. The scope of that project entitled 'Sustainable Production of Biologically Active Molecules of Marine Based Origin' (BAMMBO) is outlined. Although the Union is a global leader in many technologies, it faces increasing competition from traditional rivals and emerging economies alike and must therefore improve its innovation performance. For this reason innovation is placed at the heart of a European Horizon 2020 Strategy wherein the challenge is to connect economic performance to eco performance. This article provides a synopsis of the research activities of the BAMMBO project as they fit within the wider scope of sustainable environmentally conscientious marine resource exploitation for high-value biomolecules. Copyright © 2013 Elsevier B.V. All rights reserved.

  16. Greenhouse gas emissions from production chain of a cigarette manufacturing industry in Pakistan.

    Science.gov (United States)

    Hussain, Majid; Zaidi, Syed Mujtaba Hasnian; Malik, Riffat Naseem; Sharma, Benktesh Dash

    2014-10-01

    This study quantified greenhouse gas (GHG) emissions from the Pakistan Tobacco Company (PTC) production using a life cycle approach. The PTC production chain comprises of two phases: agricultural activities (Phase I) and industrial activities (Phase II). Data related to agricultural and industrial activities of PTC production chain were collected through questionnaire survey from tobacco growers and records from PTC manufacturing units. The results showed that total GHG emissions from PTC production chain were 44,965, 42,875, and 43,839 tCO2e respectively in 2009, 2010, and 2011. Among the agricultural activities, firewood burning for tobacco curing accounted for about 3117, 3565, and 3264 tCO2e, fertilizer application accounted for 754, 3251, and 4761 tCO2e in 2009, 2010, and 2011, respectively. Among the industrial activities, fossil fuels consumption in stationary sources accounted for 15,582, 12,733, and 13,203 tCO2e, fossil fuels used in mobile sources contributed to 2693, 3038, and 3260 tCO2e, and purchased electricity consumed resulted in 15,177, 13,556, and 11,380 tCO2e in 2009, 2010, and 2011, respectively. The GHG emissions related to the transportation of raw materials and processed tobacco amounted to 6800, 6301, and 7317 respectively in 2009, 2010, and 2011. GHG emissions from energy use in the industrial activities constituted the largest emissions (i.e., over 80%) of GHG emissions as PTC relies on fossil fuels and fossil fuel based electrical power in industrial processes. The total emissions of carbon footprint (CFP) from PTC production were 0.647 tCO2e per million cigarettes produced in 2009, 0.675 tCO2e per million cigarettes in 2010 and 0.59 tCO2e per million cigarettes in 2011. Potential strategies for GHG emissions reductions for PTC production chain include energy efficiency, reducing reliance on fossil fuels in non-mobile sources, adoption of renewable fuels including solar energy, energy from crop residues, and promotion of organic

  17. Step-Based Data Sharing and Exchange in One-of-a-Kind Product Collaborative Design for Cloud Manufacturing

    Directory of Open Access Journals (Sweden)

    B. M. Li

    2013-01-01

    Full Text Available With the trend for global collaboration, there is a need for collaborative design between geographically distributed teams and companies. In particular, this need is inevitable in the companies doing their business based on one-of-a-kind production (OKP. One important problem is the lack of interoperability and compatibility of data between different CAx systems. This problem is further highlighted in data exchange in cloud manufacturing. To the best of authors' knowledge, current studies have limitations in achieving the interoperability and compatibility of data. In this paper, a STEP-based data model is proposed to represent OKP product data/knowledge, which contains four categories of product knowledge (i.e., customer, product, manufacturing, and resource resp.. A STEP-based data modelling approach is proposed to describe each category of knowledge separately and then connect them to form the final integrated model. Compared with most current product models, this model includes the more complete product data/knowledge involved in OKP product development (OKPPD, and thus it can provide more adequate knowledge support for OKPPD activities. Based on the proposed STEP-based data model, a product data exchange and sharing (DES framework is proposed and developed to enable DES in collaborative OKPPD in the cloud manufacturing environment. Case studies were carried out to validate the proposed data model and DES framework.

  18. Influence of Different Container Closure Systems and Capping Process Parameters on Product Quality and Container Closure Integrity (CCI) in GMP Drug Product Manufacturing.

    Science.gov (United States)

    Mathaes, Roman; Mahler, Hanns-Christian; Roggo, Yves; Huwyler, Joerg; Eder, Juergen; Fritsch, Kamila; Posset, Tobias; Mohl, Silke; Streubel, Alexander

    2016-01-01

    Capping equipment used in good manufacturing practice manufacturing features different designs and a variety of adjustable process parameters. The overall capping result is a complex interplay of the different capping process parameters and is insufficiently described in literature. It remains poorly studied how the different capping equipment designs and capping equipment process parameters (e.g., pre-compression force, capping plate height, turntable rotating speed) contribute to the final residual seal force of a sealed container closure system and its relation to container closure integrity and other drug product quality parameters. Stopper compression measured by computer tomography correlated to residual seal force measurements.In our studies, we used different container closure system configurations from different good manufacturing practice drug product fill & finish facilities to investigate the influence of differences in primary packaging, that is, vial size and rubber stopper design on the capping process and the capped drug product. In addition, we compared two large-scale good manufacturing practice manufacturing capping equipment and different capping equipment settings and their impact on product quality and integrity, as determined by residual seal force.The capping plate to plunger distance had a major influence on the obtained residual seal force values of a sealed vial, whereas the capping pre-compression force and the turntable rotation speed showed only a minor influence on the residual seal force of a sealed vial. Capping process parameters could not easily be transferred from capping equipment of different manufacturers. However, the residual seal force tester did provide a valuable tool to compare capping performance of different capping equipment. No vial showed any leakage greater than 10(-8)mbar L/s as measured by a helium mass spectrometry system, suggesting that container closure integrity was warranted in the residual seal force range

  19. Production Decision Based on Discounted Price and Delivery Frequency for Garment Original Equipment Manufacturer with Constrained Capacity

    Institute of Scientific and Technical Information of China (English)

    HUO Yanfang; GU Yajie; HAN Lin; WANG Xize

    2017-01-01

    Original equipment manufacturers (OEM) have never been so important and powerful as it is today in garment manufacturing industry.The OEM supplier's production decisions always have a great impact on the market performance and the profits of a garment brand manufacturer.With constrained capacity and multiply buyers,how to make reasonable production decisions is an urgent problem for OEM suppliers.A price discount model with a single OEM supplier and two buyers is proposed to deal with the problem.Based on this model,the OEM supplier could satisfy buyers' demands and guarantee their profits as well through adjusting price and delivery frequency.A numerical example validates the validity of the model.

  20. New Product Development for Green and Low-Carbon Products—A Case Study of Taiwan's TFT-LCD Manufacturer

    Science.gov (United States)

    Lin, Chun-Yu; Lee, Amy H. I.

    2011-11-01

    Green supply chain has become an important topic these days due to pollution, global warming, extreme climatic events, etc. A green product is manufactured with the goal of reducing the damage to the environment and limiting the use of energy and other resources at any stage of its life, including raw materials, manufacture, use, and disposal. Carbon footprint is a good measure of the impact that a product has on the environment, especially in climate change, in the entire lifetime of the product. Carbon footprint is directly linked to CO2 emission; thus, the reduction of CO2 emission must be considered in the product life cycle. Although more and more researchers are working on the green supply chain management in the past few years, few have incorporated CO2 emission or carbon footprint into the green supply chain system. Therefore, this research aims to propose an integrated model for facilitating the new product development (NPD) for green and low-carbon products. In this research, a systematic model based on quality function deployment (QFD) is constructed for developing green and low-carbon products in a TFT-LCD manufacturer. Literature review and interviews with experts are done first to collect the factors for developing and manufacturing green and low-carbon products. Fuzzy Delphi method (FDM) is applied next to extract the important factors, and fuzzy interpretive structural modeling (FISM) is used subsequently to understand the relationships among factors. A house of quality (HOQ) for product planning is built last. The results shall provide important information for a TFT-LCD firm in designing a new product.

  1. Quantifying the Water Footprint of Manufactured Products: A Case Study of Pitcher Water Filters

    Directory of Open Access Journals (Sweden)

    Ashley Barker

    2012-01-01

    Full Text Available Fresh water is a finite resource that is critically needed bysociety for a variety of purposes. The demand for freshwater will grow as the world population and global livingstandard increase, and fresh water shortages will becomemore commonplace. This will put significant stress onsociety. It has been argued that fresh water may becomethe next oil, and efforts have to be made to better manageits fresh water consumption by agricultural and domesticusers. Industry also uses large amounts. Surprisingly, onlyrecently is serious attention being directed toward waterrelatedissues. This effort to quantify the water footprint ofa manufactured product represents one of the first initiativesto characterize the role of water in a discrete good.This study employed a life cycle assessment methodologyto determine the water footprint of a pitcher water filter.This particular product was selected because many waterintensivematerials and processes are needed to produceits major components: for example, agricultural processesused to produce activated carbon and petrochemicalprocesses used to produce the polypropylene casing. Inaddition, a large amount of water is consumed during theproduct’s use phase. Water data was obtained from theEcoinvent 2.1 database and categorized as either beingassociated with blue or green water.The blue water footprint (surface water consumption forthe pitcher water filter was 76 gallons per filter: 10 gallonsconsumed for materials extraction, 15 gallons for themanufacturing stage, and 50 gallons during the use phase.The green water footprint (precipitation was associatedwith the cultivation of the coconut tree; activated carbonis obtained from the coconut shells. The green waterfootprint was calculated to be 164 gallons per filter.The overall water footprint was 240 gallons per filter;the filter footprint is heavily dominated by green water(68% rather than blue water (32%. Future studies mayinvestigate how the production and

  2. Presence and biological activity of antibiotics used in fuel ethanol and corn co-product production.

    Science.gov (United States)

    Compart, D M Paulus; Carlson, A M; Crawford, G I; Fink, R C; Diez-Gonzalez, F; Dicostanzo, A; Shurson, G C

    2013-05-01

    Antibiotics are used in ethanol production to control bacteria from competing with yeast for nutrients during starch fermentation. However, there is no published scientific information on whether antibiotic residues are present in distillers grains (DG), co-products from ethanol production, or whether they retain their biological activity. Therefore, the objectives of this study were to quantify concentrations of various antibiotic residues in DG and determine whether residues were biologically active. Twenty distillers wet grains and 20 distillers dried grains samples were collected quarterly from 9 states and 43 ethanol plants in the United States. Samples were analyzed for DM, CP, NDF, crude fat, S, P, and pH to describe the nutritional characteristics of the samples evaluated. Samples were also analyzed for the presence of erythromycin, penicillin G, tetracycline, tylosin, and virginiamycin M1, using liquid chromatography and mass spectrometry. Additionally, virginiamycin residues were determined, using a U.S. Food and Drug Administration-approved bioassay method. Samples were extracted and further analyzed for biological activity by exposing the sample extracts to 10(4) to 10(7) CFU/mL concentrations of sentinel bacterial strains Escherichia coli ATCC 8739 and Listeria monocytogenes ATCC 19115. Extracts that inhibited bacterial growth were considered to have biological activity. Physiochemical characteristics varied among samples but were consistent with previous findings. Thirteen percent of all samples contained low (≤1.12 mg/kg) antibiotic concentrations. Only 1 sample extract inhibited growth of Escherichia coli at 10(4) CFU/mL, but this sample contained no detectable concentrations of antibiotic residues. No extracts inhibited Listeria monocytogenes growth. These data indicate that the likelihood of detectable concentrations of antibiotic residues in DG is low; and if detected, they are found in very low concentrations. The inhibition in only 1 DG

  3. Productivity impact of headache on a heavy-manufacturing workforce in Turkey

    Science.gov (United States)

    2013-01-01

    Background Headache disorders cause substantial productivity losses through absenteeism and impaired effectiveness at work (presenteeism). We measured productivity losses from both causes at a heavy-manufacturing company with a largely male workforce in north-western Turkey. Methods We used the HALT Index as the survey instrument. We first assessed productivity losses by surveying the entire workforce. Because we anticipated much non-participation, we also applied HALT at the annual health-checks provided to all employees by the company’s on-site health clinic. Results Mean age of the workforce (N = 7,200) was 31 yr. About two thirds (90% male) were manual workers rotating weekly through early, late and night shifts. One third (50% male) were clerical/managerial, working a standard 5-day week. In the first assessment, 3,939 questionnaires (54.7%) were returned with usable data. In the previous 3 months, absenteeism of ≥1 day was reported by 360 respondents (9.1%), of whom 4 (0.10%) recorded ≥45 days (average per worker: 0.92 days/yr). Presenteeism equivalent to ≥1 day’s absence was reported by 1,187 respondents (29.4%) (average per worker: 6.0 days/yr). We estimated that 23,519 days/yr were lost in total among respondents (2.3% of workforce capacity). In the first 6 months of annual health-checks, 2,691 employees (37.4%) attended (94.4% male). Absenteeism was reported by 40 (1.5%), with 74 days lost, presenteeism by 348 (12.9%), with 1,240 days lost. We estimated that, altogether, 41,771 man-days/yr were lost in the entire workforce (2.4% of capacity; 94% due to presenteeism), closely matching the earlier estimate. A small minority (5.7%) of those with headache, who were only 2.5% of the workforce, accounted for >45% of presenteeism-related lost productivity. Conclusion The high productivity losses in a largely male workforce were surprising. Possible factors were the nature of the work – manual labour for two thirds, often heavy – and

  4. Manufacturing validation of biologically functional T cells targeted to CD19 antigen for autologous adoptive cell therapy

    Science.gov (United States)

    Hollyman, Daniel; Stefanski, Jolanta; Przybylowski, Mark; Bartido, Shirley; Borquez-Ojeda, Oriana; Taylor, Clare; Yeh, Raymond; Capacio, Vanessa; Olszewska, Malgorzata; Hosey, James; Sadelain, Michel; Brentjens, Renier J.; Rivière, Isabelle

    2009-01-01

    Summary Based on promising pre-clinical data demonstrating the eradication of systemic B cell malignancies by CD19-targeted T lymphocytes in vivo in SCID beige mouse models, we are launching Phase 1 clinical trials in patients with chronic lymphocytic leukemia (CLL) and acute lymphoblastic leukemia (ALL). We present here the validation of the bioprocess we developed for the production and expansion of clinical grade autologous T cells derived from patients with CLL. We demonstrate that T cells genetically modified with a replication-defective gammaretroviral vector derived from the Moloney murine leukemia virus encoding a chimeric antigen receptor (CAR) targeted to CD19 (1928z) can be expanded with Dynabeads® CD3/CD28. This bioprocess allows us to generate clinical doses of 1928z+ T cells in approximately 2 to 3 weeks in a large-scale semi-closed culture system using the Wave bioreactor. These 1928z+ T cells remain biologically functional not only in vitro but also in SCID beige mice bearing disseminated tumors. The validation requirements in terms of T cell expansion, T cell transduction with the 1928z CAR, biological activity, quality control testing and release criteria were met for all four validation runs using apheresis products from patients with CLL. Additionally, following expansion of the T cells, the diversity of the skewed Vβ T cell receptor repertoire was significantly restored. This validated process will be used in phase I clinical trials in patients with chemo-refractory CLL and in patients with relapsed ALL. It can also be adapted for other clinical trials involving the expansion and transduction of patient or donor T cells using any chimeric antigen receptor or T cell receptor. PMID:19238016

  5. Application of the flotation process in the silver recovery from the wastes generated during the silvery semi-products manufacturing

    OpenAIRE

    B. Oleksiak; A. Blacha-Grzechnik; G. Siwiec

    2012-01-01

    In this work, the results of the flotation process application in the silver recovery from the wastes generated during the silvery semi-products manufacturing, are shown. The flotation process parameters, i.e. time of process, rotation frequency, gas flow rate and flotation reagents, were optimized.

  6. Application of the flotation process in the silver recovery from the wastes generated during the silvery semi-products manufacturing

    Directory of Open Access Journals (Sweden)

    B. Oleksiak

    2012-07-01

    Full Text Available In this work, the results of the flotation process application in the silver recovery from the wastes generated during the silvery semi-products manufacturing, are shown. The flotation process parameters, i.e. time of process, rotation frequency, gas flow rate and flotation reagents, were optimized.

  7. The balance between safety and productivity and its relationship with human factors and safety awareness and communication in aircraft manufacturing

    NARCIS (Netherlands)

    Karanikas, N.; Melis, Damien Jose; Kourousis, Kyriakos

    2017-01-01

    Background: This paper presents the findings of a pilot research survey which assessed the degree of balance between safety and productivity, and its relationship with awareness and communication of human factors and safety rules in the aircraft manufacturing environment. Methods: The study was

  8. Production of porous sintered materials using wastes of manufacturing engineering in self-propagating high-temperature synthesis

    Directory of Open Access Journals (Sweden)

    Y. S. Povstyana

    2016-06-01

    Full Text Available The increasing amount of wastes produced by the manufacturing engineering, as well as their physical and mechanical properties and restorability provide a search for sphere of their application. The actual problem of modern science is the utilization of wastes and using them in further production that will minimize their harmful impact on the environment and reduce the cost of expensive raw materials. Wastes are ideally suitable for the manufacture of porous permeable materials (filters. Powder metallurgy allows obtaining products with controlled filtration, physical and mechanical properties. Such materials are good filters for regeneration of technical liquids, oils, cooling fluids, sewage etc. The article analyzes the methods and technologies for the manufacture of porous ceramic materials and a new technology for their manufacture, which is based on use of mill scale and natural mineral – saponite as the main components. Compression technology provides products at low pressures and sintering by passing high-temperature synthesis. The proposed technology is characterized by low cost and good physical and mechanical properties of the product that gives a reason to use them for filtering and regeneration of technical liquids.

  9. Did technology shocks drive the great depression? Explaining cyclical productivity movements in US manufacturing, 1919-1939

    NARCIS (Netherlands)

    Inklaar, Robert; de Jong, Herman; Gouma, Reitze

    2011-01-01

    Technology shocks and declining productivity have been advanced as important factors driving the Great Depression in the United States, based on real business cycle theory. We estimate an improved measure of technology for interwar manufacturing, using data from the U.S. census reports. There is

  10. Human embryonic stem cells and good manufacturing practice: Report of a 1- day workshop held at Stem Cell Biology Research Center, Yazd, 27th April 2017

    Directory of Open Access Journals (Sweden)

    Fatemeh Akyash

    2017-09-01

    Full Text Available This report explains briefly the minutes of a 1-day workshop entitled; “human embryonic stem cells (hESCs and good manufacturing practice (GMP” held by Stem Cell Biology Research Center based in Yazd Reproductive Sciences Institute at Shahid Sadoughi University of Medical Sciences, Yazd, Iran on 27th April 2017. In this workshop, in addition to the practical sessions, Prof. Harry D. Moore from Centre for Stem Cell Biology, University of Sheffield, UK presented the challenges and the importance of the biotechnology of clinical-grade human embryonic stem cells from first derivation to robust defined culture for therapeutic applications.

  11. Human embryonic stem cells and good manufacturing practice: Report of a 1- day workshop held at Stem Cell Biology Research Center, Yazd, 27th April 2017.

    Science.gov (United States)

    Akyash, Fatemeh; Sadeghian-Nodoushan, Fatemeh; Tahajjodi, Somayyeh Sadat; Nikukar, Habib; Farashahi Yazd, Ehsan; Azimzadeh, Mostafa; D Moore, Harry; Aflatoonian, Behrouz

    2017-05-01

    This report explains briefly the minutes of a 1-day workshop entitled; "human embryonic stem cells (hESCs) and good manufacturing practice (GMP)" held by Stem Cell Biology Research Center based in Yazd Reproductive Sciences Institute at Shahid Sadoughi University of Medical Sciences, Yazd, Iran on 27 th April 2017. In this workshop, in addition to the practical sessions, Prof. Harry D. Moore from Centre for Stem Cell Biology, University of Sheffield, UK presented the challenges and the importance of the biotechnology of clinical-grade human embryonic stem cells from first derivation to robust defined culture for therapeutic applications.

  12. IMPLEMENTATION OF LEAN MANUFACTURING IN FISH CANNING COMPANY: A CASE STUDY OF A CANNED SARDINES PRODUCTION COMPANY IN MOROCCO

    Directory of Open Access Journals (Sweden)

    I. Idrıssi

    2015-12-01

    Full Text Available Lean is a powerful tool, which can bring significant benefit to manufacturing industries by creating value through reduction of waste. Although the lean concept has become very popular in mass production industries such as the automotive industry, more recently the concept has been adopted in different batch processing industries and service sectors. The application of lean tools into the food processing industry has not received the same level of attention compared to the traditional manufacturing industries. The paper discusses how the lean concept could be applied to a fish manufacturing company. The paper first presents the lean concept tools. The empirical section discusses how a case company, operating as a contract manufacturer in the food industry, has applied the lean production concept and tools. In the case study, three analysis tools are examined and the structures of demand chains of different customers are presented. The delivery times will decrease and more flexibility will be needed from the contract manufacturer. The case study shows that much movement is possible toward the lean supply chain and partnership-based cooperation. By implementing the lean concept, food companies can increase customer value through cost reduction or through provision of additional value-enhanced services.

  13. Production of biologically active recombinant human factor H in Physcomitrella.

    Science.gov (United States)

    Büttner-Mainik, Annette; Parsons, Juliana; Jérôme, Hanna; Hartmann, Andrea; Lamer, Stephanie; Schaaf, Andreas; Schlosser, Andreas; Zipfel, Peter F; Reski, Ralf; Decker, Eva L

    2011-04-01

    The human complement regulatory serum protein factor H (FH) is a promising future biopharmaceutical. Defects in the gene encoding FH are associated with human diseases like severe kidney and retinal disorders in the form of atypical haemolytic uremic syndrome (aHUS), membranoproliferative glomerulonephritis II (MPGN II) or age-related macular degeneration (AMD). There is a current need to apply intact full-length FH for the therapy of patients with congenital or acquired defects of this protein. Application of purified or recombinant FH (rFH) to these patients is an important and promising approach for the treatment of these diseases. However, neither protein purified from plasma of healthy individuals nor recombinant protein is currently available on the market. Here, we report the first stable expression of the full-length human FH cDNA and the subsequent production of this glycoprotein in a plant system. The moss Physcomitrella patens perfectly suits the requirements for the production of complex biopharmaceuticals as this eukaryotic system not only offers an outstanding genetical accessibility, but moreover, proteins can be produced safely in scalable photobioreactors without the need for animal-derived medium compounds. Transgenic moss lines were created, which express the human FH cDNA and target the recombinant protein to the culture supernatant via a moss-derived secretion signal. Correct processing of the signal peptide and integrity of the moss-produced rFH were verified via peptide mapping by mass spectrometry. Ultimately, we show that the rFH displays complement regulatory activity comparable to FH purified from plasma. © 2010 The Authors. Plant Biotechnology Journal © 2010 Society for Experimental Biology, Association of Applied Biologists and Blackwell Publishing Ltd.

  14. INTELLECTUAL CAPITAL AND VALUE CREATION IN THE METAL PRODUCTS MANUFACTURING SEGMENT

    Directory of Open Access Journals (Sweden)

    Joao Francisco Aguiar

    2010-07-01

    Full Text Available The historical evolution of the ratio of investments in intangible assets over GNP in the US economy from 1959 to 2007 – which reached 8 to 10% in 2007 - indicates a positive long term trend that is as relevant as the rate of investments in tangible assets in terms of the GNP, during the same timeframe.  The most surprising fact however, was the expansion beyond expectations over the last 40 years. According to international researchers, this trend is due to a combination of a series of causes, such as the financial globalization, market deregulation and exponential growth of technological changes, rousing the interest of entrepreneurs, scholars and researchers in becoming acquainted with indicators, classifying and ideating these so as to comprehend the value creation  process within companies. The purpose of this line of research was to test Pulic´s Value Added Intellectual Coefficient Model (2000, so as to evaluate its significance in creating value, as applied to the Metal Products Manufacturing segment, utilizing an adjusted data base obtained from the Brazilian Geography and Statistics Institute´s (IBGE Annual Industrial Research (PIA for the period 2000 to 2006, comprising companies with more than 100 employees throughout Brazil, resorting to a panel of static data. Results obtained demonstrate a positive relationship between VAIC and value creation as well as between the Calculated Intangible Value – CIV, (explanatory variable and value creation. Key-Words:  Intellectual Capital. VAIC. Value Creation. IBGE (Brazilian Geography and Statistics Institute.

  15. A new study of the kinetics of curd production in the process of cheese manufacture.

    Science.gov (United States)

    Muñoz, Susana Vargas; Torres, Maykel González; Guerrero, Francisco Quintanilla; Talavera, Rogelio Rodríguez

    2017-11-01

    We studied the role played by temperature and rennet concentration in the coagulation process for cheese manufacture and the evaluation of their kinetics. We concluded that temperature is the main factor that determines the kinetics. The rennet concentration was unimportant probably due to the fast action of the enzyme chymosin. The Dynamic light scattering technique allowed measuring the aggregate's size and their formation kinetics. The volume fraction of solids was determined from viscosity measurements, showing profiles that are in agreement with the size profiles. The results indicate that the formation of the aggregates for rennet cheese is strongly dependent on temperature and rennet concentration. The results revealed that at 35·5 °C the volume fraction of solids has the maximum slope, indicating that at this temperature the curd is formed rapidly. The optimal temperature throughout the process was established. Second-order kinetics were obtained for the process. We observed a quadratic dependence between the rennet volume and the volume fraction of solids (curd), thereby indicating that the kinetics of the curd production should be of order two.

  16. Inter-firm relations in global manufacturing: disintegrated production and its globalization

    NARCIS (Netherlands)

    Herrigel, G.; Zeitlin, J.; Morgan, G.; Campbell, J.; Crouch, C.; Pedersen, O.K.; Whitley, R.

    2010-01-01

    This chapter surveys the state of international scholarly debate on inter-firm relations in global manufacturing. It focuses on the evolving strategies of customers and suppliers within the value chains of core manufacturing industries, such as motor vehicles and complex mechanical engineering

  17. 7 CFR 947.134 - Establishment of list of manufacturers of potato products.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Establishment of list of manufacturers of potato... AGRICULTURE IRISH POTATOES GROWN IN MODOC AND SISKIYOU COUNTIES, CALIF., AND IN ALL COUNTIES IN OREGON, EXCEPT MALHEUR COUNTY Rules and Regulations Safeguards § 947.134 Establishment of list of manufacturers of potato...

  18. Comparative labour productivity performance in Chinese manufacturing, 1952-1997 : An ICOP PPP approach

    NARCIS (Netherlands)

    Wu, Harry X.

    2001-01-01

    This study joins the debate of whether Chinese manufacturing has experienced a significant catch-up with or a process of falling behind the world’s advanced economies. It calculates a new set of industry-of-origin China-US PPPs for major manufacturing industries at 1987 prices. Then using a newly

  19. Integrated anaerobic/aerobic biological treatment for intensive swine production.

    Science.gov (United States)

    Bortone, Giuseppe

    2009-11-01

    Manure processing could help farmers to effectively manage nitrogen (N) surplus load. Many pig farms have to treat wastewater. Piggery wastewater treatment is a complex challenge, due to the high COD and N concentrations and low C/N ratio. Anaerobic digestion (AD) could be a convenient pre-treatment, particularly from the energetic view point and farm income, but this causes further reduction of C/N ratio and makes denitrification difficult. N removal can only be obtained integrating anaerobic/aerobic treatment by taking into account the best use of electron donors. Experiences gained in Italy during development of integrated biological treatment approaches for swine manure, from bench to full scale, are reported in this paper. Solid/liquid separation as pre-treatment of raw manure is an efficient strategy to facilitate liquid fraction treatment without significantly lowering C/N ratio. In Italy, two full scale SBRs showed excellent efficiency and reliability. Current renewable energy policy and incentives makes economically attractive the application of AD to the separated solid fraction using high solid anaerobic digester (HSAD) technology. Economic evaluation showed that energy production can reduce costs up to 60%, making sustainable the overall treatment.

  20. 76 FR 13646 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2011-03-14

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug... public. Name of Committee: Vaccines and Related Biological Products Advisory Committee. General Function... Polysaccharides, Division of Bacterial, Parasitic, and Allergenic Products, Office of Vaccines Research and Review...

  1. 76 FR 55397 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2011-09-07

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug... public. Name of Committee: Vaccines and Related Biological Products Advisory Committee. General Function... Laboratory of Method Development, Division of Viral Products, Office of Vaccines Research and Review, Center...

  2. Analysis of manual material handling activity to increase work productivity (Case study: manufacturing company

    Directory of Open Access Journals (Sweden)

    Suryoputro Muhammad Ragil

    2018-01-01

    Full Text Available Manual material handling is one of work activities that have an effect on the physical aspect of workers in manufacturing industry, it is necessary to do the analysis of the risks from such activities. Analysis was performed on worker when performing manual lifting activity and when using two tools (Automatic Handlift and Manual Handlift. In addition to analyse in ergonomics aspect, time study analysis and productivity measurement were carried out to determine the effects of the equipment. Nordic Body Map (NBM questionnaire on worker using Automatic Handlift showed declining level of musculoskeletal disorders by 22%. REBA method obtained score of 10 and was declined to 4 after using these tool. The results of MPL method showed declining of Fc value from 4756.37 N to 1346.56 N. The results of RWL method showed declining of LI value (Lifting Index origin and destination from 1.84 and 1.18 to 1.12 and 0.89 respectively. As for worker using Manual Handlift, NBM questionnaire result shows declining level of musculoskeletal disorders by 57%. REBA method obtained scores of 8 and was reduced to 5. For MPL methode result, the Fc value is 4906.99 N and reduced to 2047.88 N. RWL method results showed declining of LI value (Lifting Index origin and destination from 1.02 and 0.67 to 0.74 and 0.58. The results of time study analysis showed declining of Standard Time when use the two tools and make the increasing productivity of 9% by worker using Automatic Hadlift and 4% by worker using Manual Handlift.

  3. CO_2 emissions reduction of Chinese light manufacturing industries: A novel RAM-based global Malmquist–Luenberger productivity index

    International Nuclear Information System (INIS)

    Emrouznejad, Ali; Yang, Guo-liang

    2016-01-01

    Climate change has become one of the most challenging issues facing the world. Chinese government has realized the importance of energy conservation and prevention of the climate changes for sustainable development of China's economy and set targets for CO_2 emissions reduction in China. In China industry contributes 84.2% of the total CO_2 emissions, especially manufacturing industries. Data envelopment analysis (DEA) and Malmquist productivity (MP) index are the widely used mathematical techniques to address the relative efficiency and productivity of a group of homogenous decision making units, e.g. industries or countries. However, in many real applications, especially those related to energy efficiency, there are often undesirable outputs, e.g. the pollutions, waste and CO_2 emissions, which are produced inevitably with desirable outputs in the production. This paper introduces a novel Malmquist–Luenberger productivity (MLP) index based on directional distance function (DDF) to address the issue of productivity evolution of DMUs in the presence of undesirable outputs. The new RAM (Range-adjusted measure)-based global MLP index has been applied to evaluate CO_2 emissions reduction in Chinese light manufacturing industries. Recommendations for policy makers have been discussed. - Highlights: •CO_2 emissions reduction in Chinese light manufacturing industries are measured. •A novel RAM based Malmquist–Luenberger productivity index has been developed. •Recommendation to policy makers for reducing CO_2 reduction in China are given.

  4. Biological hydrogen production by dark fermentation: challenges and prospects towards scaled-up production.

    Science.gov (United States)

    RenNanqi; GuoWanqian; LiuBingfeng; CaoGuangli; DingJie

    2011-06-01

    Among different technologies of hydrogen production, bio-hydrogen production exhibits perhaps the greatest potential to replace fossil fuels. Based on recent research on dark fermentative hydrogen production, this article reviews the following aspects towards scaled-up application of this technology: bioreactor development and parameter optimization, process modeling and simulation, exploitation of cheaper raw materials and combining dark-fermentation with photo-fermentation. Bioreactors are necessary for dark-fermentation hydrogen production, so the design of reactor type and optimization of parameters are essential. Process modeling and simulation can help engineers design and optimize large-scale systems and operations. Use of cheaper raw materials will surely accelerate the pace of scaled-up production of biological hydrogen. And finally, combining dark-fermentation with photo-fermentation holds considerable promise, and has successfully achieved maximum overall hydrogen yield from a single substrate. Future development of bio-hydrogen production will also be discussed. Copyright © 2011 Elsevier Ltd. All rights reserved.

  5. Lean manufacturing and Toyota Production System terminology applied to the procurement of vascular stents in interventional radiology.

    Science.gov (United States)

    de Bucourt, Maximilian; Busse, Reinhard; Güttler, Felix; Wintzer, Christian; Collettini, Federico; Kloeters, Christian; Hamm, Bernd; Teichgräber, Ulf K

    2011-08-01

    OBJECTIVES: To apply the economic terminology of lean manufacturing and the Toyota Production System to the procurement of vascular stents in interventional radiology. METHODS: The economic- and process-driven terminology of lean manufacturing and the Toyota Production System is first presented, including information and product flow as well as value stream mapping (VSM), and then applied to an interdisciplinary setting of physicians, nurses and technicians from different medical departments to identify wastes in the process of endovascular stent procurement in interventional radiology. RESULTS: Using the so-called seven wastes approach of the Toyota Production System (waste of overproducing, waiting, transport, processing, inventory, motion and waste of defects and spoilage) as well as further waste characteristics (gross waste, process and method waste, and micro waste), wastes in the process of endovascular stent procurement in interventional radiology were identified and eliminated to create an overall smoother process from the procurement as well as from the medical perspective. CONCLUSION: Economic terminology of lean manufacturing and the Toyota Production System, especially VSM, can be used to visualise and better understand processes in the procurement of vascular stents in interventional radiology from an economic point of view.

  6. Life-Cycle Assessment of Energy and Environmental Impacts of LED Lighting Products Part 2: LED Manufacturing and Performance

    Energy Technology Data Exchange (ETDEWEB)

    Scholand, Michael; Dillon, Heather E.

    2012-05-01

    Part 2 of the project (this report) uses the conclusions from Part 1 as a point of departure to focus on two objectives: producing a more detailed and conservative assessment of the manufacturing process and providing a comparative LCA with other lighting products based on the improved manufacturing analysis and taking into consideration a wider range of environmental impacts. In this study, we first analyzed the manufacturing process for a white-light LED (based on a sapphire-substrate, blue-light, gallium-nitride LED pumping a yellow phosphor), to understand the impacts of the manufacturing process. We then conducted a comparative LCA, looking at the impacts associated with the Philips Master LEDbulb and comparing those to a CFL and an incandescent lamp. The comparison took into account the Philips Master LEDbulb as it is now in 2012 and then projected forward what it might be in 2017, accounting for some of the anticipated improvements in LED manufacturing, performance and driver electronics.

  7. EMPIRICAL STUDY ON THE ROLE OF COLLABORATION IN NEW PRODUCT DEVELOPMENT IN MANUFACTURING COMPANIES

    Directory of Open Access Journals (Sweden)

    Hao Anh Nguyen

    2018-06-01

    Full Text Available This paper provides new empirical evidence on the effects of internal collaboration (manufacturing involvement and external collaboration (supplier and customer involvement practices on NPD performance and success. Moreover, comparing the collaboration practices and their effects on NPD across 10 countries are provided. Data were collected from high-performance manufacturing (HPM project with the sample of 265 manufacturing companies from 10 countries across the world. Descriptive, variance, correlation and regression analysis were conducted by using SPSS 22.0. Significant linkage between three collaboration practices and NPD performance & NPD success was found by statistical analysis. In addition, the results of this study reveal the significant differences in the implementation of collaboration practices across countries and the effects of those practices on NPD performance and success among countries. This study suggests that high performance and high success rate of NPD process could be achieved by external and internal collaboration in manufacturing companies.

  8. Design and application of reconfigurable manufacturing systems in agile mass customization manufacturing environment.

    CSIR Research Space (South Africa)

    Xing, B

    2007-05-01

    Full Text Available processes. Many manufacturing techniques are based on the principles of Flexible Manufacturing and Dedicated Manufacturing for mass production. Reconfigurable Manufacturing System, (RMS), is a manufacturing system that can provide for Agile Manufacturing...

  9. Development of biological platform for the autotrophic production of biofuels

    Science.gov (United States)

    Khan, Nymul

    The research described herein is aimed at developing an advanced biofuel platform that has the potential to surpass the natural rate of solar energy capture and CO2 fixation. The underlying concept is to use the electricity from a renewable source, such as wind or solar, to capture CO 2 via a biological agent, such as a microbe, into liquid fuels that can be used for the transportation sector. In addition to being renewable, the higher rate of energy capture by photovoltaic cells than natural photosynthesis is expected to facilitate higher rate of liquid fuel production than traditional biofuel processes. The envisioned platform is part of ARPA-E's (Advanced Research Projects Agency - Energy) Electrofuels initiative which aims at supplementing the country's petroleum based fuel production with renewable liquid fuels that can integrate easily with the existing refining and distribution infrastructure (http://arpae. energy.gov/ProgramsProjects/Electrofuels.aspx). The Electrofuels initiative aimed to develop liquid biofuels that avoid the issues encountered in the current generation of biofuels: (1) the reliance of biomass-derived technologies on the inefficient process of photosynthesis, (2) the relatively energy- and resource-intensive nature of agronomic processes, and (3) the occupation of large areas of arable land for feedstock production. The process proceeds by the capture of solar energy into electrical energy via photovoltaic cells, using the generated electricity to split water into molecular hydrogen (H2) and oxygen (O2), and feeding these gases, along with carbon dioxide (CO2) emitted from point sources such as a biomass or coal-fired power plant, to a microbial bioprocessing platform. The proposed microbial bioprocessing platform leverages a chemolithoautotrophic microorganism (Rhodobacter capsulatus or Ralstonia eutropha) naturally able to utilize these gases as growth substrates, and genetically modified to produce a triterpene hydrocarbon fuel

  10. [Characteristics of volatile organic compounds (VOCs) emission from electronic products processing and manufacturing factory].

    Science.gov (United States)

    Cui, Ru; Ma, Yong-Liang

    2013-12-01

    Based on the EPA method T0-11 and 14/15 for measurement of toxic organics in air samples, fast VOCs detector, Summa canister and DNPH absorbent were used to determine the VOCs concentrations and the compositions in the ambient air of the workshops for different processes as well as the emission concentration in the exhaust gas. In all processes that involved VOCs release, concentrations of total VOCs in the workshops were 0.1-0.5 mg x m(-3), 1.5-2.5 mg x m(-3) and 20-200 mg x m(-3) for casting, cutting and painting respectively. Main compositions of VOCs in those workshops were alkanes, eneynes, aromatics, ketones, esters and ethers, totally over 20 different species. The main compositions in painting workshop were aromatics and ketones, among which the concentration of benzene was 0.02-0.34 mg x m(-3), toluene was 0.24-3.35 mg x m(-3), ethyl benzene was 0.04-1.33 mg x m(-3), p-xylene was 0.13-0.96 mg x m(-3), m-xylene was 0.02-1.18 mg x m(-3), acetone was 0.29-15.77 mg x m(-3), 2-butanone was 0.06-22.88 mg x m(-3), cyclohexene was 0.02-25.79 mg x m(-3), and methyl isobutyl ketone was 0-21.29 mg x m(-3). The VOCs emission from painting process was about 14 t x a(-1) for one single manufacturing line, and 840 t x a(-1) for the whole factory. According to the work flows and product processes, the solvent used during painting process was the main source of VOCs emission, and the exhaust gas was the main emission point.

  11. Quantification of Bufadienolides in Bryophyllum pinnatum Leaves and Manufactured Products by UHPLC-ESIMS/MS.

    Science.gov (United States)

    Oufir, Mouhssin; Seiler, Christina; Gerodetti, Manon; Gerber, Julia; Fürer, Karin; Mennet-von Eiff, Monica; Elsas, Siegward-M; Brenneisen, Rudolf; von Mandach, Ursula; Hamburger, Matthias; Potterat, Olivier

    2015-08-01

    A quantitative assay for determination of the main bufadienolides bersaldegenin-1-acetate (1), bersaldegenin-3-acetate (2), bryophyllin A (3), and bersaldegenin-1,3,5-orthoacetate (4) in Bryophyllum pinnatum leaves and manufactured products was developed and validated. The assay involved extraction by pressurised liquid extraction, followed by quantification by ultrahigh performance liquid chromatography-tandem mass spectroscopy. The ultrahigh performance liquid chromatography-tandem mass spectroscopy method was applied to various batches of leaves harvested on several dates from plants grown at two locations (Brazil and Germany). In addition, press juices prepared from plants cultivated in Germany and Brazil were analysed. The total bufadienolide content ranged from 16.28 to 40.50 mg/100 g dry weight in leaves from plants grown in Brazil. The total content of these four bufadienolides was significantly lower in plants cultivated in Germany (3.78-12.49 mg/100 g dry weight, resp.). The total amounts of bufadienolides were 0.091-0.163 mg/100 mL and 0.89-1.16 mg/100 mL in press juices obtained from plants cultivated in Germany and Brazil, respectively. When analysing single leaves from individual plants, the content of bufadienolides was markedly higher in young leaves. For comparative purposes, the content of these bufadienolides was also determined in Bryophyllum daigremontianum and Bryophyllum tubiflorum. Bersaldegenin-1,3,5-orthoacetate (4) was predominant in the leaves of B. daigremontianum and in the stems of B. tubiflorum, while the leaves of B. tubiflorum contained very low amounts of 1-4. Georg Thieme Verlag KG Stuttgart · New York.

  12. Prototype development of educational program for production manager leading new perspectives on manufacturing technology

    OpenAIRE

    Ishii, Kazuyoshi; Ikeda, Hiroshi; Tsuchiya, Akinori; Shikida, Asami; Abe, Takehiko

    2006-01-01

    In this paper proposes the basic concept of an educational system and shows the result of educational program developed for manufacturing manager in leadership roles who wish to create new values in manufacturing technology. The basic concept combines an intelligent knowledge-based approach with the kaizen activity program in a framework of new value creation and comparative advantage models based on the ABC-G network (Academia, Business, Consultants, and Governmental officers). The education...

  13. Applicability of chemical vapour polishing of additive manufactured parts to meet production-quality

    DEFF Research Database (Denmark)

    Pedersen, D. B.; Hansen, H. N.; Nielsen, J. S.

    2014-01-01

    The Fused Deposition Modelling (FDM) method is the most rapidly growing Additive Manufacturing (AM) method[1]. FDM employs a 2.5D deposition scheme which induce a step-ladder shaped surface definition [2], with seams of the individual layers clearly visible[3]. This paper investigate to which...... of FDM manufactured parts can be taken from their current quality into the precision engineering domain....

  14. MECHANICAL PROPERTIES OF PARTS OF MEDICAL PRODUCTS PRODUCED USING ADDITIVE MANUFACTURING TECHNOLOGIES

    Directory of Open Access Journals (Sweden)

    Filip Górski

    2017-06-01

    Full Text Available The paper presents results of tests conducted on the elements of medical devices - slings used with medical lifts - manufactured using additive technologies. Project assumptions were: to produce 100 samples of clips with varying design, material and orientation parameter. Samples were manufactured using FDM and SLA processes and then tested for mechanical strength, load transmission and functionality, using certified equipment. Paper shows full methodology and obtained test results.

  15. Manufacture of immunoglobulin products for patients with primary antibody deficiencies – the effect of processing conditions on product safety and efficacy

    Directory of Open Access Journals (Sweden)

    Albert eFarrugia

    2014-12-01

    Full Text Available Early preparations of immunoglobulin (IG manufactured from human plasma by ethanol (Cohn fractionation were limited in their usefulness for substitution therapy in patients with primary antibody deficiencies (PAD, as IG aggregates formed during manufacture resulted in severe systemic reactions in patients when given intravenously. Developments in manufacturing technology obviated this problem through the capacity to produce concentrated solutions of intact monomeric IG, revolutionizing PAD treatment and improving patient life expectancy and quality of life. As the need for IG has grown, manufacturers have refined further manufacturing technologies to improve yield from plasma and produce therapies which are easier and less expensive to deliver. This has led to the substitution, partly or wholly, of ethanol precipitation by other techniques such as chromatography, and has also stimulated the production of highly concentrated solutions capable of rapid infusion. IG products have been associated, since their inception, with certain adverse events, including infectious disease transmission, haemolysis and thromboembolism. The introduction of standardized manufacturing processes and dedicated pathogen elimination steps has removed the risk of infectious disease, and the focus of attention has shifted to other problems which appear to have increased over the past five years. These include haemolysis and thromboembolism, both the cause for substantial concern and the subject of recent regulatory scrutiny and actions. We review the development of manufacturing technology and the emerging evidence that changes for the optimization of yield and convenience has contributed to the recent incidents in certain adverse events. Industry measures under development will be discussed in terms of their potential to improve safety and optimize care for patients with PAD.

  16. Application of response surface methodology to maximize the productivity of scalable automated human embryonic stem cell manufacture.

    Science.gov (United States)

    Ratcliffe, Elizabeth; Hourd, Paul; Guijarro-Leach, Juan; Rayment, Erin; Williams, David J; Thomas, Robert J

    2013-01-01

    Commercial regenerative medicine will require large quantities of clinical-specification human cells. The cost and quality of manufacture is notoriously difficult to control due to highly complex processes with poorly defined tolerances. As a step to overcome this, we aimed to demonstrate the use of 'quality-by-design' tools to define the operating space for economic passage of a scalable human embryonic stem cell production method with minimal cell loss. Design of experiments response surface methodology was applied to generate empirical models to predict optimal operating conditions for a unit of manufacture of a previously developed automatable and scalable human embryonic stem cell production method. Two models were defined to predict cell yield and cell recovery rate postpassage, in terms of the predictor variables of media volume, cell seeding density, media exchange and length of passage. Predicted operating conditions for maximized productivity were successfully validated. Such 'quality-by-design' type approaches to process design and optimization will be essential to reduce the risk of product failure and patient harm, and to build regulatory confidence in cell therapy manufacturing processes.

  17. Hydrological structure and biological productivity of the tropical Indian Ocean

    Digital Repository Service at National Institute of Oceanography (India)

    Muraleedharan, U.D.; Muraleedharan, P.M.

    Hydrological structure analyses of regions in the tropical Atlantic Ocean have consistently revealed the existence of a typical tropical structure characterized by a nitrate-depleted mixed layer above the thermocline. The important biological...

  18. 37 CFR 1.779 - Calculation of patent term extension for a veterinary biological product.

    Science.gov (United States)

    2010-07-01

    ... period beginning on the date the authority to prepare an experimental biological product under the Virus... diligence; (iii) One-half the number of days remaining in the period defined by paragraph (c)(1) of this... experimental biological product under the Virus-Serum-Toxin Act was submitted before November 16, 1988, by— (A...

  19. 75 FR 59729 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2010-09-28

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug... public. Name of Committee: Vaccines and Related Biological Products Advisory Committee. General Function... vaccines for a post-exposure prophylaxis indication using the animal rule. On November 17, 2010, the...

  20. 75 FR 2876 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2010-01-19

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug...: Vaccines and Related Biological Products Advisory Committee. General Function of the Committee: To provide... virus vaccine for the 2010 - 2011 influenza season. FDA intends to make background material available to...

  1. 76 FR 3639 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2011-01-20

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug...: Vaccines and Related Biological Products Advisory Committee. General Function of the Committee: To provide... the influenza virus vaccine for the 2011-2012 influenza season. The committee will also hear an update...

  2. 78 FR 5465 - Vaccines and Related Biological Products Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2013-01-25

    ...] Vaccines and Related Biological Products Advisory Committee; Notice of Meeting AGENCY: Food and Drug...: Vaccines and Related Biological Products Advisory Committee. General Function of the Committee: To provide... virus vaccine for the 2013- 2014 influenza season. FDA intends to make background material available to...

  3. 21 CFR 310.4 - Biologics; products subject to license control.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Biologics; products subject to license control... to license control. (a) If a drug has an approved license under section 351 of the Public Health.... (b) To obtain marketing approval for radioactive biological products for human use, as defined in...

  4. Advanced glycation end-products: a biological consequence of lifestyle contributing to cancer disparity

    OpenAIRE

    Turner, David P.

    2015-01-01

    Low income, poor diet, obesity and a lack of exercise are inter-related lifestyle factors that can profoundly alter our biological make-up to increase cancer risk, growth and development. We recently reported a potential mechanistic link between carbohydrate derived metabolites and cancer which may provide a biological consequence of lifestyle that can directly impact tumor biology. Advanced glycation end-products (AGEs) are reactive metabolites produced as a by-product of sugar metabolism. F...

  5. Design of an Orthopedic Product by Using Additive Manufacturing Technology: The Arm Splint.

    Science.gov (United States)

    Blaya, Fernando; Pedro, Pilar San; Silva, Julia López; D'Amato, Roberto; Heras, Enrique Soriano; Juanes, Juan Antonio

    2018-02-05

    The traditional fabrication process of custom-made splints has hardly undergone any progress since the beginning of its use at the end of the eighteenth century. New manufacturing techniques and the new materials can help to modernize this treatment method of fractures. The use of Additive Manufacturing has been proposed in recent years as an alternative process for the manufacture of splints and there has been an increase in public awareness and exploration. For this reason, in this study a splint model printed in 3D, that replaces the deficiencies of the cast maintaining its virtues, has been proposed. The proposed methodology is based on three-dimensional digitalization techniques and 3D modeling with reverse engineering software. The work integrates different scientific disciplines to achieve its main goal: to improve life quality of the patient. In addition, the splint has been designed based on the principles of sustainable development. The design of splint is made of Polycarbonate by technique of Additive Manufacturing with fused deposition manufacturing, and conceived with organic shapes, customizing openings and closing buttons with rubber. In this preliminary study the final result is a prototype of the 3D printed arm splint in a reduced scale by using PLA as material.

  6. Development of manufacturing process for production of 500 MWe calandria sheets

    International Nuclear Information System (INIS)

    Hariharan, R.; Ramesh, P.; Lakshminarayana, B.; Bhaskara Rao, C.V.; Pande, P.; Agarwala, G.C.

    1992-01-01

    Calandria tubes made of zircaloy-2 are being used as structural components in pressurised heavy water power reactors. The sheets required for producing calandria tube for 235 MWe reactors are being manufactured at Zircaloy Fabrication Plant (ZFP), NFC utilizing a 2 Hi/4 Hi rolling mill procured for the purpose, by carrying out cold rolling process to achieve the required size after hot rolling suitable extruded slabs. Due to limitation of width of the sheet that can be rolled with the mill as well as the size of the slab that can be extruded with the existing press, difficulties arose in producing acceptable full length sheets of size 6600 mm long x 435 mm wide x 1.6 mm thick for manufacturing 500 MWe calandria tube. This paper deals with the details of the process problem resolved. They are: (a)designing of suitable hot and cold rolling pass schedules, (b)selection and standardization of process parameters such as beta quenching, hot rolling and cold rolling, and (c)details of the overall manufacturing process. Due to implementation of above, sheets required for manufacturing 500 MWe calandria tube sheets were successfully rolled. About 40 nos. of acceptable full length sheets have already been manufactured. (author). 1 fig., 3 tabs

  7. Failure Mode and Effect Analysis (FMEA for confectionery manufacturing in developing countries: Turkish delight production as a case study

    Directory of Open Access Journals (Sweden)

    Sibel Ozilgen

    2012-09-01

    Full Text Available The Failure Mode and Effect Analysis (FMEA was applied for risk assessment of confectionary manufacturing, in whichthe traditional methods and equipment were intensively used in the production. Potential failure modes and effects as well as their possible causes were identified in the process flow. Processing stages that involve intensive handling of food by workers had the highest risk priority numbers (RPN = 216 and 189, followed by chemical contamination risks in different stages of the process. The application of corrective actions substantially reduced the RPN (risk priority number values. Therefore, the implementation of FMEA (The Failure Mode and Effect Analysis model in confectionary manufacturing improved the safety and quality of the final products.

  8. Training mechanical engineering students to utilize biological inspiration during product development.

    Science.gov (United States)

    Bruck, Hugh A; Gershon, Alan L; Golden, Ira; Gupta, Satyandra K; Gyger, Lawrence S; Magrab, Edward B; Spranklin, Brent W

    2007-12-01

    The use of bio-inspiration for the development of new products and devices requires new educational tools for students consisting of appropriate design and manufacturing technologies, as well as curriculum. At the University of Maryland, new educational tools have been developed that introduce bio-inspired product realization to undergraduate mechanical engineering students. These tools include the development of a bio-inspired design repository, a concurrent fabrication and assembly manufacturing technology, a series of undergraduate curriculum modules and a new senior elective in the bio-inspired robotics area. This paper first presents an overview of the two new design and manufacturing technologies that enable students to realize bio-inspired products, and describes how these technologies are integrated into the undergraduate educational experience. Then, the undergraduate curriculum modules are presented, which provide students with the fundamental design and manufacturing principles needed to support bio-inspired product and device development. Finally, an elective bio-inspired robotics project course is present, which provides undergraduates with the opportunity to demonstrate the application of the knowledge acquired through the curriculum modules in their senior year using the new design and manufacturing technologies.

  9. Estimating and Forecasting Production and Orders in Manufacturing Industry from Business Survey Data: Evidence from Switzerland, 1990-2003

    OpenAIRE

    Richard Etter; Michael Graff

    2003-01-01

    A fundamental issue for policy-oriented business cycle research is access to leading - or at least coincident - and reliable indicators of economic activity in manufacturing industry. Therefore, we analyse how the quickly disposable, qualitative information of the business tendency survey conducted by the Swiss Institute for Business Cycle Research (KOF) is related to the official production and order statistics of Switzerland. Pairs of high cross-correlations were selected for further analys...

  10. Failure Mode and Effect Analysis (FMEA) for confectionery manufacturing in developing countries: Turkish delight production as a case study

    OpenAIRE

    Ozilgen,Sibel

    2012-01-01

    The Failure Mode and Effect Analysis (FMEA) was applied for risk assessment of confectionary manufacturing, in whichthe traditional methods and equipment were intensively used in the production. Potential failure modes and effects as well as their possible causes were identified in the process flow. Processing stages that involve intensive handling of food by workers had the highest risk priority numbers (RPN = 216 and 189), followed by chemical contamination risks in different stages of the ...

  11. Development of a PVD-based manufacturing process of monolithic LEU irradiation targets for {sup 99}Mo production

    Energy Technology Data Exchange (ETDEWEB)

    Hollmer, Tobias

    2015-08-03

    {sup 99}Mo is the most important radioisotope in nuclear medicine. It is produced by fission of uranium in irradiation targets. The usage of cylindrical monolithic targets can ensure a safe supply of {sup 99}Mo and at the same reduce the amount of highly radioactive waste generated during production. To manufacture these targets, a novel PVD-based technique was developed. Both the feasibility and the high efficiency of this process were demonstrated in a prototype apparatus.

  12. Characterization and Conditions of the Internationalization Process of Companies in the Plastic Products Manufacturing Subsector in Bogota

    Directory of Open Access Journals (Sweden)

    Jackson Paul Pereira Silva

    2016-04-01

    Full Text Available This paper proposes a qualitative research by conducting surveys in 30 companies from the plastic products manufacturing subsector, based on theories of internationalization. It aims to find the main determinants of internationalization of these companies, while characterizing and analyzing evidence by contrasting practice and theory, in order to explain how the dynamics in the sector and its current state are and to propose recommendations for greater competitiveness and efficiency in foreign trade.

  13. IMPLEMENTATION OF LEAN MANUFACTURING IN FISH CANNING COMPANY: A CASE STUDY OF A CANNED SARDINES PRODUCTION COMPANY IN MOROCCO

    OpenAIRE

    I. Idrıssi; A. Mesfioui; I. Aftais; B. Benazzouz

    2015-01-01

    Lean is a powerful tool, which can bring significant benefit to manufacturing industries by creating value through reduction of waste. Although the lean concept has become very popular in mass production industries such as the automotive industry, more recently the concept has been adopted in different batch processing industries and service sectors. The application of lean tools into the food processing industry has not received the same level of attention compared...

  14. Manufacturing Steps for Commercial Production of Nano-Structure Capacitors Final Report CRADA No. TC02159.0

    Energy Technology Data Exchange (ETDEWEB)

    Barbee, T. W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Schena, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-08-29

    This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and TroyCap LLC, to develop manufacturing steps for commercial production of nano-structure capacitors. The technical objective of this project was to demonstrate high deposition rates of selected dielectric materials which are 2 to 5 times larger than typical using current technology.

  15. From e-manufacturing to Internet Product Process Development (IPPD) through remote – labs

    International Nuclear Information System (INIS)

    Nieto, Ernesto Córdoba; Parra, Paulo Andres Cifuentes; Díaz, Juan Camilo Parra

    2014-01-01

    This paper presents the research developed at Universidad Nacional de Colombia about the e-Manufacturing platform that is being developed and implemented at LabFabEx (acronym in Spanish as L aboratorio Fabrica Experimental ) . This platform besides has an approach to virtual-remote labs that have been tested by several students and engineers of different industrial fields. At this paper it is shown the physical and communication experimental platform, the general scope and characteristics of this e-Manufacturing platform and the virtual lab approach. This research project is funded by COLCIENCIAS (Administrative Department of science, technology and innovation in Colombia) and the enterprise IMOCOM S.A

  16. Metabolic engineering with systems biology tools to optimize production of prokaryotic secondary metabolites

    DEFF Research Database (Denmark)

    Kim, Hyun Uk; Charusanti, Pep; Lee, Sang Yup

    2016-01-01

    Metabolic engineering using systems biology tools is increasingly applied to overproduce secondary metabolites for their potential industrial production. In this Highlight, recent relevant metabolic engineering studies are analyzed with emphasis on host selection and engineering approaches...... for the optimal production of various prokaryotic secondary metabolites: native versus heterologous hosts (e.g., Escherichia coli) and rational versus random approaches. This comparative analysis is followed by discussions on systems biology tools deployed in optimizing the production of secondary metabolites....... The potential contributions of additional systems biology tools are also discussed in the context of current challenges encountered during optimization of secondary metabolite production....

  17. Introduction of a method for presenting health-based impacts of the emission from products, based on emission measurements of materials used in manufacturing of the products

    Energy Technology Data Exchange (ETDEWEB)

    Jørgensen, Rikke Bramming, E-mail: rikke.jorgensen@iot.ntnu.no

    2013-11-15

    A method for presenting the health impact of emissions from furniture is introduced, which could be used in the context of environmental product declarations. The health impact is described by the negative indoor air quality potential, the carcinogenic potential, the mutagenic and reprotoxic potential, the allergenic potential, and the toxicological potential. An experimental study of emissions from four pieces of furniture is performed by testing both the materials used for production of the furniture and the complete piece of furniture, in order to compare the results gained by adding emissions of material with results gained from testing the finished piece of furniture. Calculating the emission from a product based on the emission from materials used in the manufacture of the product is a new idea. The relation between calculated results and measured results from the same products differ between the four pieces of furniture tested. Large differences between measured and calculated values are seen for leather products. More knowledge is needed to understand why these differences arise. Testing materials allows us to compare different suppliers of the same material. Four different foams and three different timber materials are tested, and the results vary between materials of the same type. If the manufacturer possesses this type of knowledge of the materials from the subcontractors it could be used as a selection criterion according to production of low emission products. -- Highlights: • A method for presenting health impact of emissions is introduced. • An experimental study of emissions from four pieces of furniture is performed. • Health impact is calculated based on sum of contribution from the materials used. • Calculated health impact is compared to health impact of the manufactured product. • The results show that health impact could be useful in product development and for presentation in EPDs.

  18. Good manufacturing practices production of a purification-free oral cholera vaccine expressed in transgenic rice plants.

    Science.gov (United States)

    Kashima, Koji; Yuki, Yoshikazu; Mejima, Mio; Kurokawa, Shiho; Suzuki, Yuji; Minakawa, Satomi; Takeyama, Natsumi; Fukuyama, Yoshiko; Azegami, Tatsuhiko; Tanimoto, Takeshi; Kuroda, Masaharu; Tamura, Minoru; Gomi, Yasuyuki; Kiyono, Hiroshi

    2016-03-01

    The first Good Manufacturing Practices production of a purification-free rice-based oral cholera vaccine (MucoRice-CTB) from transgenic plants in a closed cultivation system yielded a product meeting regulatory requirements. Despite our knowledge of their advantages, plant-based vaccines remain unavailable for human use in both developing and industrialized countries. A leading, practical obstacle to their widespread use is producing plant-based vaccines that meet governmental regulatory requirements. Here, we report the first production according to current Good Manufacturing Practices of a rice-based vaccine, the cholera vaccine MucoRice-CTB, at an academic institution. To this end, we established specifications and methods for the master seed bank (MSB) of MucoRice-CTB, which was previously generated as a selection-marker-free line, evaluated its propagation, and given that the stored seeds must be renewed periodically. The production of MucoRice-CTB incorporated a closed hydroponic system for cultivating the transgenic plants, to minimize variations in expression and quality during vaccine manufacture. This type of molecular farming factory can be operated year-round, generating three harvests annually, and is cost- and production-effective. Rice was polished to a ratio of 95 % and then powdered to produce the MucoRice-CTB drug substance, and the identity, potency, and safety of the MucoRice-CTB product met pre-established release requirements. The formulation of MucoRice-CTB made by fine-powdering of drug substance and packaged in an aluminum pouch is being evaluated in a physician-initiated phase I study.

  19. Survival of Private Sector Manufacturing Establishments in Africa: The Role of Productivity and Ownership

    NARCIS (Netherlands)

    A. Shiferaw (Admasu)

    2009-01-01

    textabstractThis paper analyzes the risk of exit for privately-owned manufacturing establishments in a small African economy. It shows that changes in the structure of ownership following an economic reform have important implications on stablishment survival. The risk of exit is lower for

  20. Production software that works a guide to the concurrent development of realtime manufacturing systems

    CERN Document Server

    Courtright, Ann; Behuniak, John

    1991-01-01

    This useful reference addresses the key tasks that are integral to realtime software development in manufacturing plants: managing the design of the system, setting up and coordinating a development organization, and implementing tools for successfulcompletion and management. Both new and experienced project managers will discover how to use concurrent methodologies to create realtime systems in half the time it usually takes.