WorldWideScience

Sample records for biodiesel emulsified biodiesel

  1. Biodiesel

    Science.gov (United States)

    Biodiesel is a renewable alternative to petrodiesel that is prepared from plant oils or animal fats. Biodiesel is prepared via transesterification and the resulting fuel properties must be compliant with international fuel standards such as ASTM D6751 and EN 14214. Numerous catalysts, methods, and l...

  2. Engine performance and emission of compression ignition engine fuelled with emulsified biodiesel-water

    Science.gov (United States)

    Maawa, W. N.; Mamat, R.; Najafi, G.; Majeed Ali, O.; Aziz, A.

    2015-12-01

    The depletion of fossil fuel and environmental pollution has become world crucial issues in current era. Biodiesel-water emulsion is one of many possible approaches to reduce emissions. In this study, emulsified biodiesel with 4%, 6% and 8% of water contents were prepared to be used as fuel in a direct injection compression ignition engine. The performance indicator such as brake power, brake specific fuel consumption (BSFC) and brake thermal efficiency (BTE) and emissions such as NOx and particulate matter (PM) were investigated. The engine was set at constant speed of 2500 rpm and load from 20% to 60%. All the results were compared to B5 (blend of 95% petroleum diesel and 5% palm oil biodiesel) biodiesel. At low load, the BSFC decrease by 12.75% at 4% water ratio and decreased by 1.5% at 6% water ratio. However, the BSFC increases by 17.19% with increasing water ratio to 8% compared to B5. Furthermore, there was no significant decrease in brake power and BTE at 60% load. For 20% and 40% load there was some variance regarding to brake power and BTE. Significant reduction in NOx and PM emissions by 73.87% and 20.00% respectively were achieved with increasing water ratio to 8%. Overall, it is observed that the emulsified of biodiesel-water is an appropriate alternative fuel method to reduce emissions.

  3. Biodiesel Basics

    Energy Technology Data Exchange (ETDEWEB)

    None

    2017-09-01

    This fact sheet (updated for 2017) provides a brief introduction to biodiesel, including a discussion of biodiesel blends, which blends are best for which vehicles, where to buy biodiesel, how biodiesel compares to diesel fuel in terms of performance, the difference between biodiesel and renewable diesel, how biodiesel performs in cold weather, whether biodiesel use will plug vehicle filters, how long-term biodiesel use may affect engines, biodiesel fuel standards, and whether biodiesel burns cleaner than diesel fuel. The fact sheet also dismisses the use of vegetable oil as a motor fuel.

  4. Biodiesel Basics

    Energy Technology Data Exchange (ETDEWEB)

    Putzig, Mollie [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-10-04

    This fact sheet (updated for 2017) provides a brief introduction to biodiesel, including a discussion of biodiesel blends, which blends are best for which vehicles, where to buy biodiesel, how biodiesel compares to diesel fuel in terms of performance, the difference between biodiesel and renewable diesel, how biodiesel performs in cold weather, whether biodiesel use will plug vehicle filters, how long-term biodiesel use may affect engines, biodiesel fuel standards, and whether biodiesel burns cleaner than diesel fuel. The fact sheet also dismisses the use of vegetable oil as a motor fuel.

  5. Approach for energy saving and pollution reducing by fueling diesel engines with emulsified biosolution/ biodiesel/diesel blends.

    Science.gov (United States)

    Lin, Yuan-Chung; Lee, Wen-Jhy; Chao, How-Ran; Wang, Shu-Li; Tsou, Tsui-Chun; Chang-Chien, Guo-Ping; Tsai, Perng-Jy

    2008-05-15

    The developments of both biodiesel and emulsified diesel are being driven by the need for reducing emissions from diesel engines and saving energy. Artificial chemical additives are also being used in diesel engines for increasing their combustion efficiencies. But the effects associated with the use of emulsified additive/biodiesel/diesel blends in diesel engines have never been assessed. In this research, the premium diesel fuel (PDF) was used as the reference fuel. A soy-biodiesel was selected as the test biodiesel. A biosolution made of 96.5 wt % natural organic enzyme-7F (NOE-7F) and 3.5 wt % water (NOE-7F water) was used as the fuel additive. By adding additional 1 vol % of surfactant into the fuel blend, a nanotechnology was used to form emulsified biosolution/soy-biodiesel/PDF blends for fueling the diesel engine. We found that the emulsified biosolution/soy-biodiesel/PDF blends did not separate after being kept motionless for 30 days. The above stability suggests that the above combinations are suitable for diesel engines as alternative fuels. Particularly, we found that the emulsified biosolution/soy-biodiesel/PDF blends did have the advantage in saving energy and reducing the emissions of both particulate matters (PM) and polycyclic aromatic hydrocarbons (PAHs) from diesel engines as compared with PDF, soy-biodiesel/PDF blends, and emulsified soy-biodiesel/ PDF blends. The results obtained from this study will provide useful approaches for reducing the petroleum reliance, pollution, and global warming. However, it should be noted that NO(x) emissions were not measured in the present study which warrants the need for future investigation.

  6. Biodiesel Basics

    Energy Technology Data Exchange (ETDEWEB)

    None

    2014-07-01

    This fact sheet provides a brief introduction to biodiesel, including a discussion of biodiesel blends and specifications. It also covers how biodiesel compares to diesel fuel in terms of performance (including in cold weather) and whether there are adverse effects on engines or other systems. Finally, it discusses biodiesel fuel quality and standards, and compares biodiesel emissions to those of diesel fuel.

  7. Biodiesel Mass Transit Demonstration

    Science.gov (United States)

    2010-04-01

    The Biodiesel Mass Transit Demonstration report is intended for mass transit decision makers and fleet managers considering biodiesel use. This is the final report for the demonstration project implemented by the National Biodiesel Board under a gran...

  8. Biodiesel Emissions Analysis Program

    Science.gov (United States)

    Using existing data, the EPA's biodiesel emissions analysis program sought to quantify the air pollution emission effects of biodiesel for diesel engines that have not been specifically modified to operate on biodiesel.

  9. Biodiesel fuels

    Science.gov (United States)

    The mono-alkyl esters, most commonly the methyl esters, of vegetable oils, animal fats or other materials consisting mainly of triacylglycerols, often referred to as biodiesel, are an alternative to conventional petrodiesel for use in compression-ignition engines. The fatty acid esters that thus com...

  10. The biodiesel handbook

    National Research Council Canada - National Science Library

    Knothe, Gerhard; Krahl, Jurgen; Van Gerpen, Jon Harlan

    2010-01-01

    .... The Biodiesel Handbook delivers solutions to issues associated with biodiesel feedstocks, production issues, quality control, viscosity, stability, applications, emissions, and other environmental...

  11. Emulsifiers performance on the stability of the drilling fluid base biodiesel; Desempenho de emulsificantes sobre a estabilidade de fluido de perfuracao a base de biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Moreira, Giselle P.; Costa, Marta [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

    2008-07-01

    This work was prepared six (6) formulations of biodiesel based drilling fluids. Three formulations in the proportion oil-water 70/30 and other three in 60/40, just varying the employed surfactants: new product derived the citric acid (developed at our laboratory) and two other commercial surfactants. After production the fluids, It was analyzed them performance of the products through rheological properties to 135 deg F , filtrate volume in HPHT to 500 psi and to 200 deg F, electric stability to 135 deg F and phase separation during seven days of rest. The rheological analyses allowed to determine the behavior every fluids, though flow curves. Those fluids presented same behavior of the fluids used in oil field (Binghamianos). The laboratory tests demonstrated that new surfactant reduced the filtrated volume and provided mechanics and thermic stability. (author)

  12. Biodiesel at TRANSPETRO; Biodiesel na TRANSPETRO

    Energy Technology Data Exchange (ETDEWEB)

    Fonseca, Antonio Carlos C. da; Machado, Tupinamba da Conceicao S. [TRANSPETRO, Rio de Janeiro, RJ (Brazil)

    2008-07-01

    TRANSPETRO took the challenge, in early 2007, to design and install in less than one year, the systems of injection of Biodiesel in its Distribution Bases with loading truck. The basics premises, adopted for the development of the project, were based on the criteria of safety, operational reliability and to complying with legal deadline. These points guided the actions of Coordinating with two goals: Ensure the injection of Biodiesel according to time by law and the future flexibility of the system. Two to three sets were installed in each Distribution Base, respecting the characteristics of the market and the distance from centers producers of Biodiesel. TRANSPETRO was one of the first companies in Brazil using cutting-edge technology in injection of this product through the use of digital valves in the control of flow of the product. Sum up the storage capacity of Biodiesel the first and second phase of the project, TRANSPETRO will provide 8 to 10 days' stock of Biodiesel to its customers based on the injection of 5% to Diesel Oil. The Project Biodiesel at TRANSPETRO was differentiated by working in teams, the strategy for deployment and the modular aspect with focus on future demand. (author)

  13. Supercritical Synthesis of Biodiesel

    Directory of Open Access Journals (Sweden)

    Michel Vaultier

    2012-07-01

    Full Text Available The synthesis of biodiesel fuel from lipids (vegetable oils and animal fats has gained in importance as a possible source of renewable non-fossil energy in an attempt to reduce our dependence on petroleum-based fuels. The catalytic processes commonly used for the production of biodiesel fuel present a series of limitations and drawbacks, among them the high energy consumption required for complex purification operations and undesirable side reactions. Supercritical fluid (SCF technologies offer an interesting alternative to conventional processes for preparing biodiesel. This review highlights the advances, advantages, drawbacks and new tendencies involved in the use of supercritical fluids (SCFs for biodiesel synthesis.

  14. Catalysis in biodiesel processing

    Science.gov (United States)

    A substantial industry has grown in recent years to achieve the industrial scale production of biodiesel, a renewable replacement for petroleum-derived diesel fuel. The prevalent technology for biodiesel production at this time involves use of the long known single-use catalysts sodium hydroxide (o...

  15. Biodiesel Fuel Quality and the ASTM Biodiesel Standard

    Science.gov (United States)

    Biodiesel is usually produced from vegetable oils, animal fats and used cooking oils with alternative feedstocks such as algae receiving increasing interest. The transesterification reaction which produces biodiesel also produces glycerol and proceeds stepwise via mono- and diacylglycerol intermedi...

  16. Business management for biodiesel producers

    Energy Technology Data Exchange (ETDEWEB)

    Gerpen, Jon Van [Iowa State Univ., Ames, IA (United States)

    2004-07-01

    The material in this book is intended to provide the reader with information about the biodiesel and liquid fuels industry, biodiesel start-up issues, legal and regulatory issues, and operational concerns.

  17. Production of Biodiesel from Microalgae

    OpenAIRE

    Veillette, Marc; Chamoumi, Mostafa; Nikiema, Josiane; Faucheux, Nathalie; Heitz, Michèle

    2012-01-01

    In recent years, more attention has been paid to the use of third generation feedstocs for the production of biodiesel. One of the most promising sources of oil for biodiesel production are microalgae. They are unicellular or colonial photosynthetic organisms, with permanently increasing industrial application in the production of not only chemicals and nutritional supplements but also biodiesel. Biodiesel productivity per hectare of cultivation area can be...

  18. Biodiesel production technologies: review

    Directory of Open Access Journals (Sweden)

    Shemelis Nigatu Gebremariam

    2017-05-01

    Full Text Available Biodiesel is a fuel with various benefits over the conventional diesel fuel. It is derived from renewable resources, it has less emission to environment, it is biodegradable so has very limited toxicity and above all its production can be decentralized so that it could have a potential in helping rural economies. However, there are also some worth mentioning challenges associated with production of biodiesel. Among them repeatedly mentioned are the cost of feedstock and the choice of convenient technology for efficient production of the fuel from diverse feedstock types. There are four main routes by which raw vegetable oil and/or animal fat can be made suitable for use as substituent fuel in diesel engines without modification. These are direct use or blending of oils, micro-emulsion, thermal cracking or pyrolysis and transesterification reaction. Due to the quality of the fuel produced, the transesterification method is the most preferred way to produce biodiesel from diverse feedstock types. Through this method, oils and fats (triglycerides are converted to their alkyl esters with reduced viscosity to near diesel fuel levels. There are different techniques to carry out transesterification reaction for biodiesel production. Each technique has its own advantages and disadvantages as well as its own specifically convenient feedstock character. There are also some very important reaction conditions to be given due attention in each of this techniques for efficient production of biodiesel, such as molar ratio of alcohol to oil, type and amount of catalyst, reaction temperature, reaction time, reaction medium, type and relative amount of solvents, among others. This review is meant to investigate the main transesterification techniques for biodiesel production in terms of their choice of feedstock character as well as their determinately required reaction conditions for efficient biodiesel production, so that to give an overview on their advantages

  19. Sustainable Biocatalytic Biodiesel Production

    DEFF Research Database (Denmark)

    Güzel, Günduz

    and chemical equilibria as part of his main sustainable biodiesel project. The transesterification reaction of vegetable oils or fats with an aliphatic alcohol – in most cases methanol or ethanol – yields biodiesel (long-chain fatty acid alkyl esters – FAAE) as the main product in the presence of alkaline......As part of his PhD studies, Gündüz Güzel examined the thermodynamics of reactions involved in biocatalytic biodiesel production processes, with a specific focus on phase equilibria of reactive systems. He carried out the thermodynamic analyses of biocatalytic processes in terms of phase....../acid catalysts or biocatalysts (free or immobilised lipase enzymes). The reaction by-product glycerol is immiscible with the ester products (FAAE and oils/fats) in addition to the partial miscibility problem of methanol or ethanol with oils/fats. The insoluble parts of alcohol feeds or by-products form emulsion...

  20. Biodiesel Handling and Use Guide (Fifth Edition)

    Energy Technology Data Exchange (ETDEWEB)

    Alleman, T.L.; McCormick, R.L.; Christensen, E.D.; Fioroni, G.; Moriarty. K.; Yanowitz, J.

    2016-11-08

    This document is a guide for those who blend, distribute, and use biodiesel and biodiesel blends. It provides basic information on the proper and safe use of biodiesel and biodiesel blends in engines and boilers, and is intended to help fleets, individual users, blenders, distributors, and those involved in related activities understand procedures for handling and using biodiesel fuels.

  1. Analysis of biodiesel

    Science.gov (United States)

    Biodiesel is a biogenic alternative to diesel fuel derived from petroleum. It is produced by a transesterification reaction from materials consisting largely of triacylglycerols such as vegetable and other plant oils, animal fats, used cooking oils, and “alternative” feedstocks such as algal oils. T...

  2. Why Teach about Biodiesel?

    Science.gov (United States)

    Lawrence, Richard

    2002-01-01

    Proposes that study of biodiesel as a healthier alternative to petroleum diesel be included in the curriculum. Suggests that teachers will play a critical role during the transition away from fossil fuel technologies. Provides background information and web-based resources. (DLH)

  3. Biodiesel scenario in India

    Energy Technology Data Exchange (ETDEWEB)

    Taj, S. [Bangalore Univ., Al-Ameen College, Bangalore (India). Dept. of Chemistry; Prasad, H. [Bangalore Univ., Central College, Bangalore (India). Dept. of Chemistry; Ramesh, N. [Reva College, Bangladore (India); Papavinasam, S. [Natural Resources Canada, Ottawa, ON (Canada). CANMET Materials Technology Lab

    2009-08-15

    This article presented an overview of biodiesel production in India. Biodiesel has gained widespread acceptance in the United States and the European Union as a substitute for diesel. In early 2003, the Indian National Planning Commission launched a program to also foster development of vegetable oil based biofuels in order to address the energy challenges facing India. Approximately 57 per cent of rural Indian households are still not connected to the power grid, and India imports 75 per cent of its total petroleum. The National Planning Commission advocated widespread planting of an inedible, but high-yielding tree-born oilseed known as jatropha curcas that would serve as the primary feedstock for the production of vegetable oil based biofuels. Jatropha and pongamia are widely recognized as the most economically viable and environmentally neutral feedstock options. Both of these tree-borne oilseeds are adaptable to reasonably harsh climatic and growing conditions, enabling them to be cultivated on wastelands that are not currently used in agricultural production. The Commission recommended that 11.2 million hectares of jatropha be cultivated on marginal waste lands which would, over time, replace 20 per cent of total national diesel consumption with biodiesel. Both public and private sector players have begun to act on the Commission's plan. More than a hundred thousand hectares of jatropha have been planted and private firms have begun to build biodiesel processing plants. State-owned petroleum product marketing firms have committed to distributing biodiesel through some existing distribution channels. 8 refs., 6 tabs., 3 figs.

  4. Biodiesel Fuel Technology for Military Application

    National Research Council Canada - National Science Library

    Frame, Edwin

    1997-01-01

    This program addressed the effects of biodiesel (methyl soyate) and blends of biodiesel with petrofuels on fuel system component and material compatibility, fuel storage stability, and fuel lubricity...

  5. Biodiesel production using heterogeneous catalysts.

    Science.gov (United States)

    Semwal, Surbhi; Arora, Ajay K; Badoni, Rajendra P; Tuli, Deepak K

    2011-02-01

    The production and use of biodiesel has seen a quantum jump in the recent past due to benefits associated with its ability to mitigate greenhouse gas (GHG). There are large number of commercial plants producing biodiesel by transesterification of vegetable oils and fats based on base catalyzed (caustic) homogeneous transesterification of oils. However, homogeneous process needs steps of glycerol separation, washings, very stringent and extremely low limits of Na, K, glycerides and moisture limits in biodiesel. Heterogeneous catalyzed production of biodiesel has emerged as a preferred route as it is environmentally benign needs no water washing and product separation is much easier. The present report is review of the progress made in development of heterogeneous catalysts suitable for biodiesel production. This review shall help in selection of suitable catalysts and the optimum conditions for biodiesel production. Copyright © 2010 Elsevier Ltd. All rights reserved.

  6. Proceedings of the 2008 marine biodiesel symposium

    International Nuclear Information System (INIS)

    2008-01-01

    In addition to producing lower hydrocarbon emissions, marine biodiesel is biodegradable and does not harm fish. This symposium was held to discuss current marine biodiesel applications and examine methods of increasing the use of biodiesel in marine environments in British Columbia (BC). Biofuel policies and mandates in the province were reviewed, and methods of expanding the biodiesel market were explored. Updates on the use of biodiesel in ferries, tugboats, and smaller marine diesel engine applications were provided. Biodiesel projects in the United States were discussed. The environmental impacts of marine biodiesel were evaluated, and federal policies and standards for biodiesel were also outlined. The symposium was divided into the following 5 main sessions: (1) policy, (2) overviews, (3) using biodiesel in marine engines, (4) biodiesel in larger marine vessels, and (5) biodiesel quality and environmental considerations. The conference featured 13 presentations, of which 4 have been catalogued separately for inclusion in this database. tabs., figs

  7. Production of biodiesel from microalgae

    Directory of Open Access Journals (Sweden)

    Danilović Bojana R.

    2014-01-01

    Full Text Available In recent years, more attention has been paid to the use of third generation feedstocs for the production of biodiesel. One of the most promising sources of oil for biodiesel production are microalgae. They are unicellular or colonial photosynthetic organisms, with permanently increasing industrial application in the production of not only chemicals and nutritional supplements but also biodiesel. Biodiesel productivity per hectare of cultivation area can be up to 100 times higher for microalgae than for oil crops. Also, microalgae can grow in a variety of environments that are often unsuitable for agricultural purposes. Microalgae oil content varies in different species and can reach up to 77% of dry biomass, while the oil productivity by the phototrophic cultivation of microalgae is up to 122 mg/l/d. Variations of the growth conditions and the implementation of the genetic engineering can induce the changes in the composition and productivity of microalgal oil. Biodiesel from microalgae can be produced in two ways: by transesterification of oil extracted from biomass or by direct transesterification of algal biomass (so called in situ transesterification. This paper reviews the curent status of microalgae used for the production of biodiesel including their isolation, cultivation, harvesting and conversion to biodiesel. Because of high oil productivity, microalgae will play a significant role in future biodiesel production. The advantages of using microalgae as a source for biofuel production are increased efficiency and reduced cost of production. Also, microalgae do not require a lot of space for growing and do not have a negative impact on the global food and water supplies. Disadvantages of using microalgae are more difficult separation of biomass and the need for further research to develop standardized methods for microalgae cultivation and biodiesel production. Currently, microalgae are not yet sustainable option for the commercial

  8. The State High Biodiesel Project

    Science.gov (United States)

    Heasley, Paul L.; Van Der Sluys, William G.

    2009-01-01

    Through a collaborative project in Pennsylvania, high school students developed a method for converting batches of their cafeteria's waste fryer oil into biodiesel using a 190 L (50 gal) reactor. While the biodiesel is used to supplement the school district's heating and transportation energy needs, the byproduct--glycerol--is used to make hand…

  9. Importance of biodiesel as transportation fuel

    International Nuclear Information System (INIS)

    Demirbas, Ayhan

    2007-01-01

    The scarcity of known petroleum reserves will make renewable energy resources more attractive. The most feasible way to meet this growing demand is by utilizing alternative fuels. Biodiesel is defined as the monoalkyl esters of vegetable oils or animal fats. Biodiesel is the best candidate for diesel fuels in diesel engines. The biggest advantage that biodiesel has over gasoline and petroleum diesel is its environmental friendliness. Biodiesel burns similar to petroleum diesel as it concerns regulated pollutants. On the other hand, biodiesel probably has better efficiency than gasoline. One such fuel for compression-ignition engines that exhibit great potential is biodiesel. Diesel fuel can also be replaced by biodiesel made from vegetable oils. Biodiesel is now mainly being produced from soybean, rapeseed and palm oils. The higher heating values (HHVs) of biodiesels are relatively high. The HHVs of biodiesels (39-41 MJ/kg) are slightly lower than that of gasoline (46 MJ/kg), petrodiesel (43 MJ/kg) or petroleum (42 MJ/kg), but higher than coal (32-37 MJ/kg). Biodiesel has over double the price of petrodiesel. The major economic factor to consider for input costs of biodiesel production is the feedstock, which is about 80% of the total operating cost. The high price of biodiesel is in large part due to the high price of the feedstock. Economic benefits of a biodiesel industry would include value added to the feedstock, an increased number of rural manufacturing jobs, an increased income taxes and investments in plant and equipment. The production and utilization of biodiesel is facilitated firstly through the agricultural policy of subsidizing the cultivation of non-food crops. Secondly, biodiesel is exempt from the oil tax. The European Union accounted for nearly 89% of all biodiesel production worldwide in 2005. By 2010, the United States is expected to become the world's largest single biodiesel market, accounting for roughly 18% of world biodiesel consumption

  10. Optimizing biodiesel production in India

    International Nuclear Information System (INIS)

    Leduc, Sylvain; Natarajan, Karthikeyan; Dotzauer, Erik; McCallum, Ian; Obersteiner, Michael

    2009-01-01

    India is expected to at least double its fuel consumption in the transportation sector by 2030. To contribute to the fuel supply, renewable energies such as jatropha appear to be an attractive resource for biodiesel production in India as it can be grown on waste land and does not need intensive water supply. In order to produce biodiesel at a competitive cost, the biodiesel supply chain - from biomass harvesting to biodiesel delivery to the consumers - is analyzed. A mixed integer linear programming model is used in order to determine the optimal number and geographic locations of biodiesel plants. The optimization is based on minimization of the costs of the supply chain with respect to the biomass, production and transportation costs. Three biodiesel blends are considered, B2, B5 and B10. For each blend, 13 scenarios are considered where yield, biomass cost, cake price, glycerol price, transport cost and investment costs are studied. A sensitivity analysis is carried out on both those parameters and the resulting locations of the plants. The emissions of the supply chain are also considered. The results state that the biomass cost has most influence on the biodiesel cost (an increase of feedstock cost increases the biodiesel cost by about 40%) and to a lower effect, the investment cost and the glycerol price. Moreover, choosing the right set of production plant locations highly depends on the scenarios that have the highest probability to occur, for which the production plant locations still produce a competitive biodiesel cost and emissions from the transportation are minimum. In this study, one set of plant locations happened to meet these two requirements.

  11. Er biodiesel en god ide?

    DEFF Research Database (Denmark)

    Schmidt, Jannick

    2007-01-01

    Biodiesel opfattes som en grøn miljøvenlig teknologi. Men har dette 'grønne' alternativ til konventionel diesel en skjult bagside af medaljen? Og kan det være, at man i stedet for at få et bedre miljø, medvirker til øgede miljøpåvirkninger i form af emissioner og naturødelæggelse, når man skifter...... til biodiesel? I artiklen belyses nogle af de mest sejlivede myter omkring biodiesel. Udgivelsesdato: Januar...

  12. Obtention and characterization of biodiesel; Obtencao e caracterizacao do biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Leonidas B.O. dos; Caitano, Moises; Aranda, Donato A.G.; Mothe, Cheila G. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil)

    2004-07-01

    Biodiesel is an ester resulting from the transesterification reaction of an alcohol and an oil obtained from biomass. The products of the transesterification are an ester and the glycerol. The biodiesel and the petroleum commercial diesel have similar properties, and they can be mixed and used in diesel motors. The use of biodiesel will allow a better exploration of the energetic potential of our cultures. The biodiesel has some advantages compared to others combustibles, such as adaptability to usual diesel motors and non-generation of NO{sub x} and SO{sub x} compounds. Many experiments with biodiesel have been made in Brazil since the 70's. This work made samples of biodiesel by transesterification batch reactions to many blends of soybean oil and residual fry oil, at room temperature, using mechanical mixture or magnetic agitation by a magnetic stirrer, using as catalysts sodium methoxide and potassium hydroxide. For each obtained sample tests to determine the Acidity Index (ABNT-MB-74), Saponification Index (ABNT-MB-75), Iodine Wijz Index (ABNT-MB- 77), thermal analysis by DTA and TG (TA Instruments SDT 2960, 30 to 800 deg C, 10 deg C/min at nitrogen atmosphere) and rheological test (Haake RS 150 Rheo Stress rheometer) were done. (author)

  13. Toxicology of Biodiesel Combustion products

    Science.gov (United States)

    1. Introduction The toxicology of combusted biodiesel is an emerging field. Much of the current knowledge about biological responses and health effects stems from studies of exposures to other fuel sources (typically petroleum diesel, gasoline, and wood) incompletely combusted. ...

  14. New technologies in biodiesel production

    International Nuclear Information System (INIS)

    Santacesaria, E.; Di Serio, M.; Tesser, R.

    2009-01-01

    The cost of biodiesel is nowadays affected by the cost of the raw materials, because the currently used method of preparation requires highly refined vegetable oils containing very low amounts of free fatty acids and moisture. Alternatively, less expensive technologies are possible using heterogeneous catalysts. In the present paper examples of these new technologies, based on the use of heterogeneous catalysts, in the production of biodiesel are described and discussed. [it

  15. Biodiesel Fuel Quality and the ASTM Standard

    Science.gov (United States)

    Biodiesel is usually produced from vegetable oils, animal fats and used cooking oils with alternative feedstocks such as algae receiving increasing interest. The transesterification reaction which produces biodiesel also produces glycerol and proceeds stepwise via mono- and diacylglycerol intermedia...

  16. Contaminantes em Biodiesel e Controle de Qualidade

    OpenAIRE

    Daiane P. C. de Quadros; UFSC; Eduardo S. Chaves; UFSC; Jessee S. A. Silva; UFSC; Leonardo S. G. Teixeira; UFBA; Adilson J. Curtius; UFSC; Pedro A. P. Pereira; Universidade Federal da Bahia

    2011-01-01

    A review on inorganic and organic contaminants in biodiesel used as fuel is presented. The main contaminants normally present in biodiesel that may affect the final product quality are discussed. The possible sources, as well as the effects of the contaminants in the production process, in the biodiesel stability and in its performance in the motor as fuel are also discussed. The criterions for the quality control of biodiesel and the limits established by the regulator agencies are described...

  17. Biodiesel Production from Spent Coffee Grounds

    OpenAIRE

    Blinová Lenka; Bartošová Alica; Sirotiak Maroš

    2017-01-01

    The residue after brewing the spent coffee grounds is an oil-containing waste material having a potential of being used as biodiesel feedstock. Biodiesel production from the waste coffee grounds oil involves collection and transportation of coffee residue, drying, oil extraction, and finally production of biodiesel. Different methods of oil extraction with organic solvents under different conditions show significant differences in the extraction yields. In the manufacturing of biodiesel from ...

  18. Biodiesel Analytical Methods: August 2002--January 2004

    Energy Technology Data Exchange (ETDEWEB)

    Van Gerpen, J.; Shanks, B.; Pruszko, R.; Clements, D.; Knothe, G.

    2004-07-01

    Biodiesel is an alternative fuel for diesel engines that is receiving great attention worldwide. The material contained in this book is intended to provide the reader with information about biodiesel engines and fuels, analytical methods used to measure fuel properties, and specifications for biodiesel quality control.

  19. Ecological Impact of Biodiesel Use

    International Nuclear Information System (INIS)

    Gulbis, V.; Shmigins, R.

    2005-01-01

    Full text: The paper presents a study of biodiesel application and its ecological impacts. Our study is based on the comparison of exhaust emission composition produced by the combustion of rapeseed oil methyl ester (RME) and conventional diesel fuel (DD) and its blends in a direct injection diesel engine XD2P (YTT). The engine was tested in biofuels laboratory of LUA Motor Vehicle Institute. Fuelling the engine with biodiesel and biodiesel/diesel blend reduced oxides of nitrogen by 17.5% (100RME) and by 5.6% (35RME) and carbon monoxide by 49.8% (100RME) and by 45.3% (35RME). Fuelling the engine with biodiesel and different biodiesel/diesel blends reduced the absorbtion coefficient by 33.9% (5RME), by 44.3% (20RME) and by 51.2% (100RME) on free acceleration regime. In these tests soot reduced by 28...76.7% at full opened throttle position with 100RME. (Authors)

  20. Biodiesel Production from Spent Coffee Grounds

    Directory of Open Access Journals (Sweden)

    Blinová Lenka

    2017-06-01

    Full Text Available The residue after brewing the spent coffee grounds is an oil-containing waste material having a potential of being used as biodiesel feedstock. Biodiesel production from the waste coffee grounds oil involves collection and transportation of coffee residue, drying, oil extraction, and finally production of biodiesel. Different methods of oil extraction with organic solvents under different conditions show significant differences in the extraction yields. In the manufacturing of biodiesel from coffee oil, the level of reaction completion strongly depends on the quality of the feedstock oil. This paper presents an overview of oil extraction and a method of biodiesel production from spent coffee grounds.

  1. Biodiesel Production from Spent Coffee Grounds

    Science.gov (United States)

    Blinová, Lenka; Bartošová, Alica; Sirotiak, Maroš

    2017-06-01

    The residue after brewing the spent coffee grounds is an oil-containing waste material having a potential of being used as biodiesel feedstock. Biodiesel production from the waste coffee grounds oil involves collection and transportation of coffee residue, drying, oil extraction, and finally production of biodiesel. Different methods of oil extraction with organic solvents under different conditions show significant differences in the extraction yields. In the manufacturing of biodiesel from coffee oil, the level of reaction completion strongly depends on the quality of the feedstock oil. This paper presents an overview of oil extraction and a method of biodiesel production from spent coffee grounds.

  2. Recent trends in biodiesel production

    Directory of Open Access Journals (Sweden)

    Meisam Tabatabaei

    2015-09-01

    Full Text Available This article fully discusses the recent trends in the production of one the most attractive types of biofuels, i.e., biodiesel.with a focus on the existing obstacles for its large scale production. Moreover, recent innovations/improvements under three categories of upstream, mainstream, and downstream processes are also presented. Upstream strategies are mainly focused on seeking more sustainable oil feedstocks and/or enhancing the quality of waste-oriented ones. The mainstream strategies section highlights the numerous attempts made to enhance agitation efficiency including chemical and/or mechanical strategies. Finally, the innovative downstream strategies basically dealing with 1 separation of biodiesel and glycerin, 2 purification of biodiesel and glycerin, and 3 improving the characteristics of the produced fuel, are comprehensively reviewed.

  3. Marine biodiesel use in the Puget Sound

    International Nuclear Information System (INIS)

    Davidson, N.

    2008-01-01

    This presentation explored the use of marine biodiesel in the Puget Sound region. Marine vessels are now adopting biodiesel fuels as a means of expressing corporate commitments to reducing greenhouse gas (GHG) emissions and the environmental impacts of hydrocarbons released into marine environments. Various biodiesel blends have been designed for use in small commercial, recreational, and research vessels. Biodiesel has also been adopted by charter and whale watching vessels in the Puget Sound. The Guemes Island Ferry has recently been re-configured to use biodiesel fuels, with 2 fuel tanks capable of receiving 2200 gallons at a time. The ferry adopted biodiesel after receiving soot complaints from marinas, and hopes to serve as a model for other vessels in the region. Four fueling docks supply the biodiesel blend to marine vessels. The sale of biodiesel has doubled in some marinas over the last 5 years. Deterrents to biodiesel use include parts incompatibilities and warranty problems. Some marinas have stopped selling biodiesel as a result of low sales and high prices. It was concluded that educational programs are needed to ensure the widespread adoption of biodiesel in the Puget Sound. refs., tabs., figs

  4. Montana BioDiesel Initiative

    Energy Technology Data Exchange (ETDEWEB)

    Peyton, Brent [Montana State Univ., Bozeman, MT (United States)

    2017-01-29

    This initiative funding helped put Montana State University (MSU) in a position to help lead in the development of biodiesel production strategies. Recent shortages in electrical power and rising gasoline prices have focused much attention on the development of alternative energy sources that will end our dependence on fossil fuels. In addition, as the concern for environmental impact of utilizing fossil fuels increases, effective strategies must be implemented to reduce emissions or the increased regulations imposed on fossil fuel production will cause economic barriers for their use to continue to increase. Biodiesel has been repeatedly promoted as a more environmentally sound and renewable source of fuel and may prove to be a highly viable solution to provide, at the least, a proportion of our energy needs. Currently there are both practical and economic barriers to the implementation of alternative energy however the advent of these technologies is inevitable. Since many of the same strategies for the storage, transport, and utilization of biodiesel are common with that of fossil fuels, the practical barriers for biodiesel are comparatively minimal. Strategies were developed to harness the CO2 as feedstock to support the growth of biodiesel producing algae. The initiative funding led to the successful funding of highly rated projects in competitive national grant programs in the National Science Foundation and the Department of Energy. This funding put MSU in a key position to develop technologies to utilize the CO2 rich emissions produced in fossil fuel utilization and assembled world experts concerning the growth characteristics of photosynthetic microorganisms capable of producing biodiesel.

  5. Biodiesel via hydrotreating of fat

    DEFF Research Database (Denmark)

    Madsen, Anders Theilgaard; Ahmed, El Hadi; Christensen, Claus Hviid

    Biodiesel production via transesterification to fatty acid alkyl esters is rising rapidly worldwide due to the limited availability of fossil resources and the problems of global warming. Often, however, the use of 2nd-generation feedstock like animal waste fat and trap greases etc. is made...

  6. Mississippi State Biodiesel Production Project

    Energy Technology Data Exchange (ETDEWEB)

    Rafael Hernandez; Todd French; Sandun Fernando; Tingyu Li; Dwane Braasch; Juan Silva; Brian Baldwin

    2008-03-20

    Biodiesel is a renewable fuel conventionally generated from vegetable oils and animal fats that conforms to ASTM D6751. Depending on the free fatty acid content of the feedstock, biodiesel is produced via transesterification, esterification, or a combination of these processes. Currently the cost of the feedstock accounts for more than 80% of biodiesel production cost. The main goal of this project was to evaluate and develop non-conventional feedstocks and novel processes for producing biodiesel. One of the most novel and promising feedstocks evaluated involves the use of readily available microorganisms as a lipid source. Municipal wastewater treatment facilities (MWWTF) in the USA produce (dry basis) of microbial sludge annually. This sludge is composed of a variety of organisms, which consume organic matter in wastewater. The content of phospholipids in these cells have been estimated at 24% to 25% of dry mass. Since phospholipids can be transesterified they could serve as a ready source of biodiesel. Examination of the various transesterification methods shows that in situ conversion of lipids to FAMEs provides the highest overall yield of biodiesel. If one assumes a 7.0% overall yield of FAMEs from dry sewage sludge on a weight basis, the cost per gallon of extracted lipid would be $3.11. Since the lipid is converted to FAMEs, also known as biodiesel, in the in Situ extraction process, the product can be used as is for renewable fuel. As transesterification efficiency increases the cost per gallon drops quickly, hitting $2.01 at 15.0% overall yield. An overall yield of 10.0% is required to obtain biodiesel at $2.50 per gallon, allowing it to compete with soybean oil in the marketplace. Twelve plant species with potential for oil production were tested at Mississippi State, MS. Of the species tested, canola, rapeseed and birdseed rape appear to have potential in Mississippi as winter annual crops because of yield. Two perennial crops were investigated, Chinese

  7. Chemical alternative to the energetic use of biodiesel; Chemische Alternativen zur energetischen Nutzung von Biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Warwel, S; Ruesch genannt Klaas, M.; Harperscheid, M. [Bundesanstalt fuer Getreide-, Kartoffel- und Fettforschung, Muenster (Germany). Inst. fuer Biochemie und Technologie der Fette - H.P. Kaufmann-Inst.

    1996-12-31

    Biodiesel is environment-friendly, but much more costly to produce than `normal` diesel fuel. Higher economic efficiency can be achieved by using biodiesel as a chemical feedstock instead. Tenside and polymers offer a wide range of applications. (orig) [Deutsch] Biodiesel ist ein umweltfreundlicher Kraftstoff, jedoch in der Herstellung deutlich teurer als Mineraloel-Dieselkraftstoff. Eine signifikant hoehere Wertschoepfung koennte errreicht werden, wenn Biodiesel nicht im Kraftstoffsektor, sondern als chemischer Rohstoff verwendet wird. Tenside und Polymere sind hierbei grossvolumige Einsatzbereiche. (orig)

  8. PRELIMINARY DESIGN OF OSCILLATORY FLOW BIODIESEL REACTOR FOR CONTINUOUS BIODIESEL PRODUCTION FROM JATROPHA TRIGLYCERIDES

    OpenAIRE

    AZHARI T. I. MOHD. GHAZI; M. F. M. GUNAM RESUL; R. YUNUS; T. C. SHEAN YAW

    2008-01-01

    The concept of a continuous process in producing biodiesel from jatropha oil by using an Oscillatory Flow Biodiesel Reactor (OFBR) is discussed in this paper. It has been recognized that the batch stirred reactor is a primary mode used in the synthesis of biodiesel. However, pulsatile flow has been extensively researcehed and the fundamental principles have been successfully developed upon which its hydrodynamics are based. Oscillatory flow biodiesel reactor offers precise control of mixing b...

  9. New regulatory landmark for biodiesel use; Novo marco regulatorio para usos de biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, Rosangela Moreira de [Agencia Nacional do Petroleo, Gas Natural e Biocombustiveis (ANP), Rio de Janeiro, RJ (Brazil)

    2008-07-01

    The Brazilian Biodiesel Production and Use of Biodiesel - PNPB, made possible the insert of Biodiesel in the Brazilian energy matrix. The National Agency of the Petroleum, Natural Gas and Biofuels - ANP was responsible to create the outline regulatory that established the rules for entrance and commercialization of this new fuel in the country. This work seeks to present the effects of the implantation of the new relative rules to the biodiesel use. (author)

  10. Biodiesel research progress 1992-1997

    Energy Technology Data Exchange (ETDEWEB)

    Tyson, K.S. [ed.

    1998-04-01

    The US Department of Energy (DOE) Office of Fuels Development began evaluating the potential of various alternative fuels, including biodiesel, as replacement fuels for traditional transportation fuels. Biodiesel is derived from a variety of biological materials from waste vegetable grease to soybean oil. This alkyl ester could be used as a replacement, blend, or additive to diesel fuel. This document is a comprehensive summary of relevant biodiesel and biodiesel-related research, development demonstration, and commercialization projects completed and/or started in the US between 1992 and 1997. It was designed for use as a reference tool to the evaluating biodiesel`s potential as a clean-burning alternative motor fuel. It encompasses, federally, academically, and privately funded projects. Research projects are presented under the following topical sections: Production; Fuel characteristics; Engine data; Regulatory and legislative activities; Commercialization activities; Economics and environment; and Outreach and education.

  11. Are subsidies for biodiesel economically efficient?

    International Nuclear Information System (INIS)

    Wassell, Charles S.; Dittmer, Timothy P.

    2006-01-01

    Biodiesel produces less pollution than petrodiesel; however, it is more expensive and will only be a viable alternative if market prices of the products are comparable. This paper examines whether the external benefits from biodiesel use justify subsidies required for adoption outside of niche alternative fuel markets. The authors establish a range of subsidies required to make biodiesel a viable substitute for petrodiesel. Published estimates of the emissions reductions from biodiesel and the dollar benefits of unit reductions in emissions are used to compute a per-gallon external benefit from use of biodiesel, versus petrodiesel. Under conservative estimates of the benefits from biodiesel use in non-road equipment, the external benefits outweigh the required subsidies.(JEL Q48, Q42, H2)

  12. Three years operational experience with biodiesel

    International Nuclear Information System (INIS)

    Murphy, J.

    2008-01-01

    TSI Terminal Systems Inc. is the largest container terminal operator in Canada, and has an annual payroll exceeding $150 million. The company started a biodiesel test program with the Canadian Bioenergy Corporation in order to assess the emission reduction impacts of using biodiesel. The pilot was tested with 6 different pieces of equipment used at the terminal over an initial period of 3 weeks. Emissions testing was then conducted for different biodiesel blend levels and compared with baseline data in relation to particulate matter, total hydrocarbons, carbon monoxide (CO), carbon dioxide (CO 2 ), and nitrous oxides (NO x ). Results of the tests confirmed that the biodiesel blends significantly reduced emissions at the terminal and confirmed the operability of biodiesel. Overall emissions were reduced by 30 per cent. The fuel is now being used in all the company's equipment. The use of the biodiesel has not resulted in any engine failures or power losses. tabs., figs

  13. Correlating Engine NOx Emission with Biodiesel Composition

    Science.gov (United States)

    Jeyaseelan, Thangaraja; Mehta, Pramod Shankar

    2017-06-01

    Biodiesel composition comprising of saturated and unsaturated fatty acid methyl esters has a significant influence on its properties and hence the engine performance and emission characteristics. This paper proposes a comprehensive approach for composition-property-NOx emission analysis for biodiesel fuels and highlights the pathways responsible for such a relationship. Finally, a procedure and a predictor equation are developed for the assessment of biodiesel NOx emission from its composition details.

  14. Genetic Engineering Strategies for Enhanced Biodiesel Production.

    Science.gov (United States)

    Hegde, Krishnamoorthy; Chandra, Niharika; Sarma, Saurabh Jyoti; Brar, Satinder Kaur; Veeranki, Venkata Dasu

    2015-07-01

    The focus on biodiesel research has shown a tremendous growth over the last few years. Several microbial and plant sources are being explored for the sustainable biodiesel production to replace the petroleum diesel. Conventional methods of biodiesel production have several limitations related to yield and quality, which led to development of new engineering strategies to improve the biodiesel production in plants, and microorganisms. Substantial progress in utilizing algae, yeast, and Escherichia coli for the renewable production of biodiesel feedstock via genetic engineering of fatty acid metabolic pathways has been reported in the past few years. However, in most of the cases, the successful commercialization of such engineering strategies for sustainable biodiesel production is yet to be seen. This paper systematically presents the drawbacks in the conventional methods for biodiesel production and an exhaustive review on the present status of research in genetic engineering strategies for production of biodiesel in plants, and microorganisms. Further, we summarize the technical challenges need to be tackled to make genetic engineering technology economically sustainable. Finally, the need and prospects of genetic engineering technology for the sustainable biodiesel production and the recommendations for the future research are discussed.

  15. Oxidation stability and risk evaluation of biodiesel

    Directory of Open Access Journals (Sweden)

    Hoshino Takashi

    2007-01-01

    Full Text Available This review describes oxidation and thermal stability and hazardous possibility of biodiesel by auto-oxidation. As it can be distributed using today’s infrastructure biodisel production has increased especially in the European Union. Biodiesel has many surpassing properties as an automotive fuel. Biodiesel is considered safer than diesel fuel because of the high flash point, but it has oxygen and double bond(s. Fatty acid methyl esters are more sensitive to oxidative degradation than fossil diesel fuel. The ability of producing peroxides is rather high, therefore we should care of handling of biodiesel.

  16. Purification of crude biodiesel using dry washing and membrane technologies

    Directory of Open Access Journals (Sweden)

    I.M. Atadashi

    2015-12-01

    Full Text Available Purification of crude biodiesel is mandatory for the fuel to meet the strict international standard specifications for biodiesel. Therefore, this paper carefully analyzed recently published literatures which deal with the purification of biodiesel. As such, dry washing technologies and the most recent membrane biodiesel purification process have been thoroughly examined. Although purification of biodiesel using dry washing process involving magnesol and ion exchange resins provides high-quality biodiesel fuel, considerable amount of spent absorbents is recorded, besides the skeletal knowledge on its operating process. Further, recent findings have shown that biodiesel purification using membrane technique could offer high-quality biodiesel fuel with less wastewater discharges. Thus, both researchers and industries are expected to benefit from the development of membrane technique in purifying crude biodiesel. As well biodiesel purification via membranes has been shown to be environmentally friendly. For these reasons, it is important to explore and exploit membrane technology to purify crude biodiesel.

  17. BiodieselAnalyzer: a user-friendly software for predicting the properties of prospective biodiesel

    Directory of Open Access Journals (Sweden)

    Ahmad Farhad Talebi

    2014-06-01

    Full Text Available The procedures used to experimentally determine the quality parameters of a biodiesel are lengthy and expensive. Occasionally it may be impossible to obtain a sufficient amount of oil for the relevant analyses. This is often the case for algal biodiesel, for example. Here we report on a new software package, the BiodieselAnalyzer© Version 1.1, for predicting the properties of a prospective biodiesel. BiodieselAnalyzer© can estimate 16 different quality parameters of a biodiesel based on the fatty acid methyl ester profile of the oil feedstock used in making it. The current version of the BiodieselAnalyzer© is intended for the Windows platform and is publically available at http://www.brteam.ir/biodieselanalyzer.

  18. WSF Biodiesel Demonstration Project Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Washington State University; University of Idaho; The Glosten Associates, Inc.; Imperium Renewables, Inc.

    2009-04-30

    In 2004, WSF canceled a biodiesel fuel test because of “product quality issues” that caused the fuel purifiers to clog. The cancelation of this test and the poor results negatively impacted the use of biodiesel in marine application in the Pacific Northwest. In 2006, The U.S. Department of Energy awarded the Puget Sound Clean Air Agency a grant to manage a scientific study investigating appropriate fuel specifications for biodiesel, fuel handling procedures and to conduct a fuel test using biodiesel fuels in WSF operations. The Agency put together a project team comprised of experts in fields of biodiesel research and analysis, biodiesel production, marine engineering and WSF personnel. The team reviewed biodiesel technical papers, reviewed the 2004 fuel test results, designed a fuel test plan and provided technical assistance during the test. The research reviewed the available information on the 2004 fuel test and conducted mock laboratory experiments, but was not able to determine why the fuel filters clogged. The team then conducted a literature review and designed a fuel test plan. The team implemented a controlled introduction of biodiesel fuels to the test vessels while monitoring the environmental conditions on the vessels and checking fuel quality throughout the fuel distribution system. The fuel test was conducted on the same three vessels that participated in the canceled 2004 test using the same ferry routes. Each vessel used biodiesel produced from a different feedstock (i.e. soy, canola and yellow grease). The vessels all ran on ultra low sulfur diesel blended with biodiesel. The percentage of biodiesel was incrementally raised form from 5 to 20 percent. Once the vessels reached the 20 percent level, they continued at this blend ratio for the remainder of the test. Fuel samples were taken from the fuel manufacturer, during fueling operations and at several points onboard each vessel. WSF Engineers monitored the performance of the fuel systems and

  19. Bio-diesel: A candidate for a Nigeria energy mix

    International Nuclear Information System (INIS)

    Eze, T.; Dim, L. A.; Funtua, I. I.; Oladipo, M. O. A.

    2011-01-01

    This paper presents a review of bio-diesel development and economic potentials. The basics of biodiesel and its production technology are described. Attention is given to development potential, challenges and prospests of bio-diesel in Nigeria with ground facts on bio-diesel production feasibility in Nigeria highlighted.

  20. Biodegradability of diesel and biodiesel blends

    African Journals Online (AJOL)

    STORAGESEVER

    2008-05-02

    May 2, 2008 ... The biodegradability of pure diesel and biodiesel and blends with different proportions of biodiesel (2%. (commercial); 5% and 20%) was evaluated employing the respirometric method and the redox indicator. 2,6-dichlorophenol indophenol (DCPIP) test. In the former, experiments simulating the ...

  1. Georges Chavanne and the first biodiesel

    Science.gov (United States)

    This article discusses the first production and use of a fuel around 1937 now called biodiesel, which is obtained from a vegetable or plant oil through a straightforward chemical reaction called transesterification. Biodiesel has become an alternative or supplement to conventional diesel fuel derive...

  2. The uses of biodiesel in buses

    International Nuclear Information System (INIS)

    Smigins, R.; Gulbis, V.

    2003-01-01

    In November 2001 in Naukseni, Valmiera district the biodiesel - methyl ester of rapeseed oil (RME) - plant first in Latvia and in all Baltic States began to work. The production capacity of the plant is 2500 t of biodiesel per year. In the summer and autumn period of the last year the first experiment using 100% RME on one city bus line was carried out. The bus Ikarus-280 in total turned 30700 km consuming 11 tons or 12600 litres of biodiesel. The fuel consumption with biodiesel was 0.9 kg/h (14.2%) or 3.01/100 km higher as with fossil diesel fuel. The engine power and the driving speed on the line were practically unchanged in spite that the heat capacity of biodiesel is lower than of ordinary diesel fuel (according 37.1 l and 42.1 MJ/kg). Using biodiesel the toxicity of the exhaust gases dropped down very essentially. It was controlled regularly by measuring the absorption coefficient and smokiness. At the end of second month of the experiment the absorption coefficient was 2.09 m -1 and 47.8%. This shows that by the influence of biodiesel the compression chambers of the engine clean from burnt parts and the combustion process most completely thanks to the oxygen content in the biodiesel (authors)

  3. Effect of biodiesel addition on microbial community structure in a simulated fuel storage system.

    Science.gov (United States)

    Restrepo-Flórez, Juan-Manuel; Bassi, Amarjeet; Rehmann, Lars; Thompson, Michael R

    2013-11-01

    Understanding changes in microbial structure due to biodiesel storage is important both for protecting integrity of storage systems and fuel quality management. In this work a simulated storage system was used to study the effect of biodiesel (0%, 25%, 50%, 75% and 100%) on a microbial population, which was followed by community level physiological profiling (CLPP), 16s rDNA analysis and plating in selective media. Results proved that structure and functionality were affected by biodiesel. CLPP showed at least three populations: one corresponding to diesel, one to biodiesel and one to blends of diesel and biodiesel. Analysis of 16s rDNA revealed that microbial composition was different for populations growing in diesel and biodiesel. Genera identified are known for degradation of hydrocarbons and emulsifier production. Maximum growth was obtained in biodiesel; however, microbial counts in standard media were lower for this samples. Acidification of culture media was observed at high biodiesel concentration. Copyright © 2013 Elsevier Ltd. All rights reserved.

  4. Microbial recycling of glycerol to biodiesel.

    Science.gov (United States)

    Yang, Liu; Zhu, Zhi; Wang, Weihua; Lu, Xuefeng

    2013-12-01

    The sustainable supply of lipids is the bottleneck for current biodiesel production. Here microbial recycling of glycerol, byproduct of biodiesel production to biodiesel in engineered Escherichia coli strains was reported. The KC3 strain with capability of producing fatty acid ethyl esters (FAEEs) from glucose was used as a starting strain to optimize fermentation conditions when using glycerol as sole carbon source. The YL15 strain overexpressing double copies of atfA gene displayed 1.7-fold increase of FAEE productivity compared to the KC3 strain. The titer of FAEE in YL15 strain reached to 813 mg L(-1) in minimum medium using glycerol as sole carbon source under optimized fermentation conditions. The titer of glycerol-based FAEE production can be significantly increased by both genetic modifications and fermentation optimization. Microbial recycling of glycerol to biodiesel expands carbon sources for biodiesel production. Copyright © 2013 Elsevier Ltd. All rights reserved.

  5. Process development for scum to biodiesel conversion.

    Science.gov (United States)

    Bi, Chong-hao; Min, Min; Nie, Yong; Xie, Qing-long; Lu, Qian; Deng, Xiang-yuan; Anderson, Erik; Li, Dong; Chen, Paul; Ruan, Roger

    2015-06-01

    A novel process was developed for converting scum, a waste material from wastewater treatment facilities, to biodiesel. Scum is an oily waste that was skimmed from the surface of primary and secondary settling tanks in wastewater treatment plants. Currently scum is treated either by anaerobic digestion or landfilling which raised several environmental issues. The newly developed process used a six-step method to convert scum to biodiesel, a higher value product. A combination of acid washing and acid catalyzed esterification was developed to remove soap and impurities while converting free fatty acids to methyl esters. A glycerol washing was used to facilitate the separation of biodiesel and glycerin after base catalyzed transesterification. As a result, 70% of dried and filtered scum was converted to biodiesel which is equivalent to about 134,000 gallon biodiesel per year for the Saint Paul waste water treatment plant in Minnesota. Copyright © 2015 Elsevier Ltd. All rights reserved.

  6. Biodiesel/Cummins CRADA Report

    Science.gov (United States)

    2014-07-01

    add CO2 to the atmosphere, but recycles existing atmospheric CO2. The use of fossil fuels on the other hand, releases carbon that has been stored...in this test was made from recycled greases (used cooking and frying oils). 2.1.2 Test Platform and Location The RDC selected the 49’ Buoy Utility... polypropylene ) over time, so these should not be used in fuel storage and transfer systems. Biodiesel/Cummins CRADA Report 5 UNCLAS//Public | CG-926 R&DC

  7. Characterization of beef tallow biodiesel and their mixtures with soybean biodiesel and mineral diesel fuel

    Energy Technology Data Exchange (ETDEWEB)

    Teixeira, Leonardo S.G. [Instituto de Quimica, Universidade Federal da Bahia, Campus Universitario de Ondina, 40.170-280, Salvador, Bahia (Brazil); INCT de Energia e Ambiente, Universidade Federal da Bahia, 40.170-280, Salvador, Bahia (Brazil); Couto, Marcelo B.; Filho, Miguel Andrade; Assis, Julio C.R.; Guimaraes, Paulo R.B.; Pontes, Luiz A.M.; Almeida, Selmo Q. [Departamento de Engenharia e Arquitetura, Universidade Salvador - UNIFACS, Av. Cardeal da Silva 132, 40.220-141, Salvador, Bahia (Brazil); Souza, Giancarlos S. [Instituto de Quimica, Universidade Federal da Bahia, Campus Universitario de Ondina, 40.170-280, Salvador, Bahia (Brazil); Teixeira, Josanaide S.R. [Instituto Federal de Educacao Ciencia e Tecnologica da Bahia - IFBAHIA, Rua Emidio de Morais S/N, 40.625-650, Salvador, Bahia (Brazil)

    2010-04-15

    Tallow is a raw material for biodiesel production that, due to their highly centralized generation in slaughter/processing facilities and historically low prices, may have energy, environmental, and economic advantages that could be exploited. However beef tallow biodiesel have unfavorable properties due the presence of high concentration of saturated fatty esters. One way to overcome these inconveniences is using blending procedures. In this way, blends of beef tallow biodiesel with soybean biodiesel and with conventional mineral diesel fuel were prepared and the quality of the mixtures was monitored with the purpose to study ideal proportions of the fuels. By measurement of the viscosity, density, cold filter plugging point, and flash point, it was demonstrated that tallow biodiesel can be blended with both mineral diesel and soybean biodiesel to improve the characteristics of the blend fuels, over that of the tallow. (author)

  8. Um desafio novo: o biodiesel Biodiesel: a new challenge

    Directory of Open Access Journals (Sweden)

    Guilherme Leite da Silva Dias

    2007-04-01

    Full Text Available Esta nota procura mostrar a natureza da regulação de combustíveis no Brasil dentro de um monopólio de fato, com preços casados para os biocombustíveis em relação a seus substitutos fósseis mais próximos. Isso cria um ambiente de remuneração para o biodiesel muito baixo, além de subordiná-lo à logística de distribuição do monopólio. Um ambiente fora do monopólio, isento de carga fiscal e de comercialização a curtas distâncias, seria mais adequado para o ambiente requerido de incentivos para a inovação tecnológica.The regulatory framework for fuels in Brazil is an effective monopoly, with matching prices for close substitutes. Biodiesel prices are unattractive because domestic diesel prices are below international relative oil prices, transportation logistics burden furthermore with unnecessary routes designed for fossil fuels, beyond heavy indirect taxation. An alternative framework, without taxation, for short distance supply, with a large variety of raw materials is better suited for technological innovation.

  9. Biodiesel production by transesterification using immobilized lipase.

    Science.gov (United States)

    Narwal, Sunil Kumar; Gupta, Reena

    2013-04-01

    Biodiesel can be produced by transesterification of vegetable or waste oil catalysed by lipases. Biodiesel is an alternative energy source to conventional fuel. It combines environmental friendliness with biodegradability, low toxicity and renewability. Biodiesel transesterification reactions can be broadly classified into two categories: chemical and enzymatic. The production of biodiesel using the enzymatic route eliminates the reactions catalysed under acid or alkali conditions by yielding product of very high purity. The modification of lipases can improve their stability, activity and tolerance to alcohol. The cost of lipases and the relatively slower reaction rate remain the major obstacles for enzymatic production of biodiesel. However, this problem can be solved by immobilizing the enzyme on a suitable matrix or support, which increases the chances of re-usability. The main factors affecting biodiesel production are composition of fatty acids, catalyst, solvents, molar ratio of alcohol and oil, temperature, water content, type of alcohol and reactor configuration. Optimization of these parameters is necessary to reduce the cost of biodiesel production.

  10. Empirical Study of the Stability of Biodiesel and Biodiesel Blends: Milestone Report

    Energy Technology Data Exchange (ETDEWEB)

    McCormick, R. L.; Westbrook, S. R.

    2007-05-01

    The objective of this work was to develop a database that supports specific proposals for a stability test and specification for biodiesel and biodiesel blends. B100 samples from 19 biodiesel producers were obtained in December of 2005 and January of 2006 and tested for stability. Eight of these samples were then selected for additional study, including long-term storage tests and blending at 5% and 20% with a number of ultra-low sulfur diesel fuels.

  11. Chemical Engineering Aspects of Biodiesel Production I. Biofuels, Biodiesel Properties and Production Technology Fundamentals

    OpenAIRE

    Sinčić, D.

    2014-01-01

    The common industrial process of biodiesel production is a sequence of particular unit operations starting with raw material preparation, followed by transesterification reaction stage and ending with reaction mixture separation and treatment. The main product is biodiesel of prescribed quality while the treatment of glycerol and salt containing phase is carried out so that the by-products obtained maximize profitability of the entire undertaking. The biodiesel production process is often ...

  12. Process Simulation of enzymatic biodiesel production -at what cost can biodiesel be made with enzymes?

    DEFF Research Database (Denmark)

    Fjerbæk Søtoft, Lene; Christensen, Knud Villy; Rong, Benguang

    The industrial production of biodiesel has had a very turbulent lifetime due to drastic changes in prices of raw materials and fossil fuels as well as regulatory changes and produced amounts of biodiesel. Biodiesel production is carried out by various forms of catalysts, but industrially only...... as well as environmental impacts of the alternative process must be evaluated towards the conventional process. With process simulation tools, an evaluation will be carried out looking at what it will cost to produce biodiesel with enzymes. Different scenarios will be taken into account with variations...

  13. Prediction of cold flow properties of Biodiesel

    Directory of Open Access Journals (Sweden)

    Parag Saxena

    2016-08-01

    Full Text Available Biodiesel being environmentally friendly is fast gaining acceptance in the market as an alternate diesel fuel. But compared to petroleum diesel it has certain limitations and thus it requires further development on economic viability and improvement in its properties to use it as a commercial fuel. The cold flow properties play a major role in the usage of biodiesel commercially as it freezes at cold climatic conditions. In the present study, cold flow properties of various types of biodiesel were estimated by using correlations available in literature. The correlations were evaluated based on the deviation between the predicted value and experimental values of cold flow properties.

  14. Aqueous solubility, dispersibility and toxicity of biodiesels

    International Nuclear Information System (INIS)

    Hollebone, B.P.; Fieldhouse, B.; Lumley, T.C.; Landriault, M.; Doe, K.; Jackman, P.

    2007-01-01

    The renewed interest in the use of biological fuels can be attributed to that fact that feedstocks for fatty-acid ester biodiesels are renewable and can be reclaimed from waste. Although there are significant benefits to using biodiesels, their increased use leaves potential for accidental release to the environment. Therefore, their environmental behaviours and impacts must be evaluated along with the risk associated with their use. Biodiesel fuels may be made from soy oil, canola oil, reclaimed restaurant grease, fish oil and animal fat. The toxicological fate of biofuel depends on the variability of its chemical composition. This study provided an initial assessment of the aqueous fate and effects of biodiesel from a broad range of commonly available feedstocks and their blends with petroleum diesels. The study focused primarily on the fate and impact of these fuels in fresh-water. The use of chemical dispersion as a countermeasure for saltwater was also investigated. The exposure of aquatic ecosystems to biodiesels and petroleum diesel occurs via the transfer of material from the non-aqueous phase liquid (NAPL) into the aqueous phase, as both soluble and dispersed components. The aqueous solubilities of the fuels were determined from the equilibrium water-accommodated fraction concentrations. The acute toxicities of many biodiesels were reported for 3 test species used by Environment Canada for toxicological evaluation, namely rainbow trout, the water flea and a luminescent bacterium. This study also evaluated the natural potential for dispersion of the fuels in the water column in both low and high-energy wave conditions. Chemical dispersion as a potential countermeasure for biodiesel spills was also evaluated using solubility testing, acute toxicity testing, and dispersibility testing. It was shown that biodiesels have much different fates and impacts from petroleum diesels. The compounds partitioning into the water column are also very different for each

  15. Biodiesel: Small Scale Production and Quality Requirements

    Science.gov (United States)

    van Gerpen, Jon

    Biodiesel is produced by reacting vegetable oils or animal fats with alcohol in the presence of an alkaline catalyst. The resulting methyl esters, which are the biodiesel fuel, are separated from the by-product glycerin, and then washed with water and dehydrated to produce fuel that must meet standardized specifications. Degraded oils containing high levels of free fatty acids can also be converted to biodiesel, but pretreatment with acid-catalyzed esterification is required. The resulting fuel is suitable for use as a neat fuel in diesel engines or blended with conventional diesel fuel.

  16. Survey of alternative feedstocks for biodiesel production

    Science.gov (United States)

    Summarized will be results obtained from the production of biodiesel from several alternative feedstocks with promising agronomic characteristics. Such feedstocks include camelina (Camelina sativa L.), coriander (Coriandrum sativum L.), field pennycress (Thlaspi arvense L.), and meadowfoam (Limnanth...

  17. Biodiesel production with immobilized lipase: A review.

    Science.gov (United States)

    Tan, Tianwei; Lu, Jike; Nie, Kaili; Deng, Li; Wang, Fang

    2010-01-01

    Fatty acid alkyl esters, also called biodiesel, are environmentally friendly and show great potential as an alternative liquid fuel. Biodiesel is produced by transesterification of oils or fats with chemical catalysts or lipase. Immobilized lipase as the biocatalyst draws high attention because that process is "greener". This article reviews the current status of biodiesel production with immobilized lipase, including various lipases, immobilization methods, various feedstocks, lipase inactivation caused by short chain alcohols and large scale industrialization. Adsorption is still the most widely employed method for lipase immobilization. There are two kinds of lipase used most frequently especially for large scale industrialization. One is Candida antartica lipase immobilized on acrylic resin, and the other is Candida sp. 99-125 lipase immobilized on inexpensive textile membranes. However, to further reduce the cost of biodiesel production, new immobilization techniques with higher activity and stability still need to be explored. Copyright 2010 Elsevier Inc. All rights reserved.

  18. Current status of biodiesel development in Brazil.

    Science.gov (United States)

    Ramos, Luiz Pereira; Wilhelm, Helena Maria

    2005-01-01

    In recent years, the concept of producing biodiesel from renewable lipid sources has regained international attention. In Brazil, a national program was launched in 2002 to evaluate the technical, economic, and environmental competitiveness of biodiesel in relation to the commercially available diesel oil. Several research projects were initiated nationwide to investigate and/or optimize biodiesel production from renewable lipid sources and ethanol derived from sugarcane (ethyl esters). Once implemented, this program will not only decrease our dependence on petroleum derivatives but also create new market opportunities for agribusiness, opening new jobs in the countryside, improving the sustainability of our energy matrix, and helping the Brazilian government to support important actions against poverty. This article discusses the efforts to develop the Brazilian biodiesel program in the context of technical specifications as well as potential oilseed sources.

  19. Isothermal calorimetry on enzymatic biodiesel production

    DEFF Research Database (Denmark)

    Fjerbæk, Lene

    2008-01-01

    information about effects taking place when using lipases immobilized on an inert carrier for transesterification of a triglyceride and an alcohol as for biodiesel production. The biodiesel is produced by rapeseed oil and methanol as well as ethanol and a commercial biocatalyst Novozym 435 from Novozymes...... containing a Candida Antarctica B lipase immobilized on an acrylic resin. The reaction investigated is characterized by immiscible liquids (oil, methanol, glycerol and biodiesel) and enzymes imm. on an inert carrier during reaction, which allows several effects to take place that during normal reaction...... conditions can not be elucidated. These effects have been observed with isothermal calorimetry bringing forth new information about the reaction of enzymes catalyzing transesterification. Enzymatic biodiesel production has until now not been investigated with isothermal microcalorimetry, but the results...

  20. Enzymatic biodiesel production: Technical and economical considerations

    DEFF Research Database (Denmark)

    Munk Nielsen, Per; Brask, Jesper; Fjerbæk, Lene

    2008-01-01

    It is well documented in the literature that enzymatic processing of oils and fats for biodiesel is technically feasible. However, with very few exceptions, enzyme technology is not currently used in commercial-scale biodiesel production. This is mainly due to non-optimized process design...... and a lack of available costeffective enzymes. The technology to re-use enzymes has typically proven insufficient for the processes to be competitive. However, literature data documenting the productivity of enzymatic biodiesel together with the development of new immobilization technology indicates...... that enzyme catalysts can become cost effective compared to chemical processing. This work reviews the enzymatic processing of oils and fats into biodiesel with focus on process design and economy....

  1. Sustainable Future for Biodiesel in Brazil

    DEFF Research Database (Denmark)

    Dias, Maria Amélia de Paula

    This thesis aims to study alternatives to biodiesel industry in Brazil, for 2030, taking in account the sustainability dimensions, namely economic, environmental, ecological, social, national and international politics, territorial, cultural, and technological, through the development of scenarios...... for agriculture and pasture. Thus, a simulation, using linear programming models, was made in order to verify the alternatives of feedstock to produce biodiesel. It was observed that it is possible to decentralize the market, reduce land use, and regionalize production, making better use of the availability...... to identify the driving forces to develop the scenario storylines. This proposition was tested in an in-depth interview with the biodiesel market stakeholders. Based on the findings of the two approaches, the simulations and the interviews, it was possible to obtain future alternatives, where the biodiesel...

  2. Indigenous algae: Potential factories for biodiesel production

    CSIR Research Space (South Africa)

    Maharajh, Dheepak M

    2008-11-01

    Full Text Available The environmental effects of burning fossil fuels and the increased crude oil prices have triggered increased interest in biofuels. Biodiesel is traditionally produced from oil seed crops, which have lower yields per land area and threaten food...

  3. Environment Friendly Biodiesel Fuel in Latvia

    OpenAIRE

    Gudriniece, E.; Strēle, M.; Skujiņš, V.

    2006-01-01

    Biodiesel fuel (RME and REE) are alternative, environment friendly fuels for diesel engines, obtained from rapeseed oil and methanol or ethanol. RME are produced with capacity 2500 t/year at SIA “Delta Riga” experimental factory Naukseni in Latvia. The laboratory method of production biodiesel fuel (REE) from rapeseed oil and ethanol has been worked out at RTU. Blends RME and REE with fossil diesel fuel are applied, as well.

  4. Degradation of automotive materials in palm biodiesel

    International Nuclear Information System (INIS)

    Fazal, M.A.; Haseeb, A.S.M.A.; Masjuki, H.H.

    2012-01-01

    As compared to petroleum diesel, biodiesel is more corrosive for automotive materials. Studies on the characterization of corrosion products of fuel exposed automotive materials are scarce. Automotive fuel system and engine components are made from different ferrous and non-ferrous materials. The present study aims to investigate the corrosion products of different types of automotive materials such as copper, brass, aluminum and cast iron upon exposure to diesel and palm biodiesel. Changes in fuel properties due to exposure of different materials were also examined. Degradation of metal surface was characterized by digital camera, SEM/EDS and X-ray diffraction (XRD). Fuel properties were examined by measuring TAN (total acid number), density and viscosity. Among the metal investigated, copper is found to be least resistant in biodiesel and formed comparatively more corrosion products than other metals. Upon exposure of metals in biodiesel, TAN number crosses the limit given by standard while density and viscosity remain within the acceptable range of limit. -- Highlights: ► Order of incompatible metals in palm biodiesel: copper > brass > aluminum > cast iron. ► The possible reactions for the degradation of copper and cast iron have been discussed. ► For metal exposed biodiesel, only TAN number crosses the limit while density and viscosity remain within the limit. ► Copper and copper based alloy (brass) increase TAN number comparatively more than other metals.

  5. Environmental sustainability of biodiesel in Brazil

    International Nuclear Information System (INIS)

    Geraldes Castanheira, Érica; Grisoli, Renata; Freire, Fausto; Pecora, Vanessa; Coelho, Suani Teixeira

    2014-01-01

    Biodiesel production in Brazil has grown from 736 m 3 in 2007 to 2.7 Mm 3 in 2012. It is an emergent bioenergy for which it is important to guarantee environmental sustainability. The objective of this article is to characterise the biodiesel production chain in Brazil, to identify potential environmental impacts and to analyse key drivers and barriers for biodiesel environmental sustainability. This article explores these aspects and focusses on the increasing demand for the main feedstocks for biodiesel production in Brazil: soybean oil and beef tallow. The impacts of land use and land-use change on greenhouse gas emissions, biodiversity and water, as well as the energy balance, were found to be critical for the environmental sustainability assessment and development of biodiesel chains. Increasing agriculture yields, diversifying feedstocks and adopting ethyl transesterification can contribute to minimise environmental impacts. It was also found that environmental impacts could be mitigated by appropriate policies aiming at an integrated optimisation of food and bioenergy production and through agro-economic–ecological zoning, allowing adequate use of land for each purpose. Despite the limitation and weakness of some sustainability tools and initiatives, certification and zoning can play an important role in the sustainability of the emerging biodiesel production in Brazil

  6. Butter as a feedstock for biodiesel production.

    Science.gov (United States)

    Haas, Michael J; Adawi, Nadia; Berry, William W; Feldman, Elaine; Kasprzyk, Stephen; Ratigan, Brian; Scott, Karen; Landsburg, Emily Bockian

    2010-07-14

    Fatty acid methyl esters (FAME) were produced from cow's milk (Bostaurus) butter by esterification/transesterification in the presence of methanol. The product was assayed according to the Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels (ASTM D 6751). The preparation failed to meet the specifications for flash point, free and total glycerin contents, total sulfur, and oxidation stability. Failures to meet the flash point and free/total glycerin specifications were determined to be due to interference with standard assays for these parameters by short-chain-length fatty acid esters. The oxidation stability of the butterfat FAME was improved by supplementation with a commercial antioxidant formulation. Approximately 725 ppm of antioxidant was required to meet the ASTM-specified stability value for biodiesel. This work indicates that, without further purification to reduce a slightly excessive sulfur content, fatty acid ester preparations produced from butter are unacceptable as sole components of a biodiesel fuel. However, it is possible that even without further purification a butter-based ester preparation could be mixed with biodiesel from other feedstocks to produce a blend that meets the current quality standards for biodiesel. The results presented here also illustrate some potential weaknesses in the accepted methods for biodiesel characterization when employed in the analysis of FAME preparations containing mid- and short-chain fatty acid esters.

  7. The effect of biodiesel policies on world biodiesel and oilseed prices

    NARCIS (Netherlands)

    Drabik, D.; Gorter, de H.; Timilsina, G.R.

    2014-01-01

    A theoretical and empirical model is developed to analyze the effect of a biodiesel mandate, a tax exemption (tax credit) and an exogenous diesel price shock on world soybean and canola markets. The jointness in crushing oil and meal from the oilseed reduces the size of the link between biodiesel

  8. Model Biaya Produksi Biodiesel Berbasis Minyak Sawit

    Directory of Open Access Journals (Sweden)

    Meilita Tryana Sembiring

    2015-06-01

    Full Text Available Biodiesel is a renewable energy source in Indonesia of which the use is regulated by the government in the form of mandatory policy of biodiesel and diesel fuel blending. The production of biodiesel in Indonesia is not developed (the need is 3.4 million kiloliters but the total national production is only 1,703 kiloliters. It is because the selling price (referring to Mean of Platts Singapore is always lower than the production cost. Biodiesel production is influenced by raw materials and process technology, so it needs to be conducted biodiesel production modeling as a basis in determining the supporting policies of biodiesel selling price. The purpose of this study is to identify the raw materials, process technology, and modeling the production cost structure of palm oil-based biodiesel. Identification of raw materials was conducted by literature study and field survey to biodiesel producers. Identification of process technology was conducted by field survey and mass balance calculation using Grand Inizio technology to get the number of yield of each raw material. Then, production cost study was based on the specifications of raw materials and process technology with heuristic approach. Types and specifications of palm oil widely used by Indonesian producers are Crude Palm Oil (CPO FFA<5%, Refined Palm Oil (RPO FFA<5%, Refined Oil FFA<1%, Palm Fatty Acid Distillated (PFAD FFA 90%. The technology process used was transesterification for FFA level <1% and esterification-transesterification for FFA level <5%. The resulting yield for 1000 kg of raw material is 1051.75 kg CPO, 975.94 kg RPO and PFAD, 973.81 kg Refined Oil with Grand Inizio technology approach. The production cost model represents the total production cost influenced by the costs of Inside Battery Limit, Outside Battery Limit, general cost and glycerol value-added.ABSTRAKBiodiesel adalah sumber energi terbarukan di Indonesia yang diatur penggunaannya oleh pemerintah dalam bentuk

  9. Algae biodiesel - a feasibility report

    Directory of Open Access Journals (Sweden)

    Gao Yihe

    2012-04-01

    Full Text Available Abstract Background Algae biofuels have been studied numerous times including the Aquatic Species program in 1978 in the U.S., smaller laboratory research projects and private programs. Results Using Molina Grima 2003 and Department of Energy figures, captial costs and operating costs of the closed systems and open systems were estimated. Cost per gallon of conservative estimates yielded $1,292.05 and $114.94 for closed and open ponds respectively. Contingency scenarios were generated in which cost per gallon of closed system biofuels would reach $17.54 under the generous conditions of 60% yield, 50% reduction in the capital costs and 50% hexane recovery. Price per gallon of open system produced fuel could reach $1.94 under generous assumptions of 30% yield and $0.2/kg CO2. Conclusions Current subsidies could allow biodiesel to be produced economically under the generous conditions specified by the model.

  10. Algae biodiesel - a feasibility report

    Science.gov (United States)

    2012-01-01

    Background Algae biofuels have been studied numerous times including the Aquatic Species program in 1978 in the U.S., smaller laboratory research projects and private programs. Results Using Molina Grima 2003 and Department of Energy figures, captial costs and operating costs of the closed systems and open systems were estimated. Cost per gallon of conservative estimates yielded $1,292.05 and $114.94 for closed and open ponds respectively. Contingency scenarios were generated in which cost per gallon of closed system biofuels would reach $17.54 under the generous conditions of 60% yield, 50% reduction in the capital costs and 50% hexane recovery. Price per gallon of open system produced fuel could reach $1.94 under generous assumptions of 30% yield and $0.2/kg CO2. Conclusions Current subsidies could allow biodiesel to be produced economically under the generous conditions specified by the model. PMID:22540986

  11. Improved oxidative stability of biodiesel fuels : antioxidant research and development.

    Science.gov (United States)

    2011-01-01

    Biodiesel is a domestic, renewable fuel that is gaining wide acceptance, especially in Europe. : When blended with conventional petroleum diesel, biodiesel reduces hydrocarbon, particulate : and carbon monoxide emissions, while having minimal to no e...

  12. Business Management for Biodiesel Producers: August 2002--January 2004

    Energy Technology Data Exchange (ETDEWEB)

    Van Gerpen, J.

    2004-07-01

    The material in this book is intended to provide the reader with information about the biodiesel and liquid fuels industry, biodiesel start-up issues, legal and regulatory issues, and operational concerns.

  13. Performance and emission characteristics of double biodiesel blends with diesel

    Directory of Open Access Journals (Sweden)

    Kuthalingam Arun Balasubramanian

    2013-01-01

    Full Text Available Recent research on biodiesel focused on performance of single biodiesel and its blends with diesel. The present work aims to investigate the possibilities of the application of mixtures of two biodiesel and its blends with diesel as a fuel for diesel engines. The combinations of Pongamia pinnata biodiesel, Mustard oil biodiesel along with diesel (PMD and combinations of Cotton seed biodiesel, Pongamia pinnata biodiesel along with diesel (CPD are taken for the experimental analysis. Experiments are conducted using a single cylinder direct-injection diesel engine with different loads at rated 3000 rpm. The engine characteristics of the two sets of double biodiesel blends are compared. For the maximum load, the value of Specific Fuel consumption and thermal efficiency of CPD-1 blend (10:10:80 is close to the diesel values. CPD blends give better engine characteristics than PMD blends. The blends of CPD are suitable alternative fuel for diesel in stationary/agricultural diesel engines.

  14. In situ Transesterification of Microalgal Oil to Produce Algal Biodiesel

    Science.gov (United States)

    2012-06-01

    This research was to process whole microalgae cells for biodiesel production without first extracting lipids. The ultimate : goal is develop a novel process for algal biodiesel production directly from microalgae cells in a single step, i.e., in situ...

  15. Evaluation of hydrolysis-esterification biodiesel production from wet microalgae.

    Science.gov (United States)

    Song, Chunfeng; Liu, Qingling; Ji, Na; Deng, Shuai; Zhao, Jun; Li, Shuhong; Kitamura, Yutaka

    2016-08-01

    Wet microalgae hydrolysis-esterification route has the advantage to avoid the energy-intensive units (e.g. drying and lipid extraction) in the biodiesel production process. In this study, techno-economic evaluation of hydrolysis-esterification biodiesel production process was carried out and compared with conventional (usually including drying, lipid extraction, esterification and transesterification) biodiesel production process. Energy and material balance of the conventional and hydrolysis-esterification processes was evaluated by Aspen Plus. The simulation results indicated that drying (2.36MJ/L biodiesel) and triolein transesterification (1.89MJ/L biodiesel) are the dominant energy-intensive stages in the conventional route (5.42MJ/L biodiesel). By contrast, the total energy consumption of hydrolysis-esterification route can be reduced to 1.81MJ/L biodiesel, and approximately 3.61MJ can be saved to produce per liter biodiesel. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Determinants of stakeholders' attitudes towards biodiesel.

    Science.gov (United States)

    Amin, Latifah; Hashim, Hasrizul; Mahadi, Zurina; Ibrahim, Maznah; Ismail, Khaidzir

    2017-01-01

    Concern about the inevitable depletion of global energy resources is rising and many countries are shifting their focus to renewable energy. Biodiesel is one promising energy source that has garnered much public attention in recent years. Many believe that this alternative source of energy will be able to sustain the need for increased energy security while at the same time being friendly to the environment. Public opinion, as well as proactive measures by key players in industry, may play a decisive role in steering the direction of biodiesel development throughout the world. Past studies have suggested that public acceptance of biofuels could be shaped by critical consideration of the risk-benefit perceptions of the product, in addition to the impact on the economy and environment. The purpose of this study was to identify the relevant factors influencing stakeholders' attitudes towards biodiesel derived from crops such as palm oil for vehicle use, as well as to analyse the interrelationships of these factors in an attitude model. A survey of 509 respondents, consisting of various stakeholder groups in the Klang Valley region of Malaysia, was undertaken. The results of the study have substantiated the premise that the most important direct predictor of attitude to biodiesel is the perceived benefits ( β  = 0.80, p  < 0.001). Attitude towards biodiesel also involves the interplay between other factors, such as engagement to biotechnology, trust of key players, attitude to technology, and perceived risk. Although perceived benefit has emerged as the main predictor of public support of biodiesel, the existence of other significant interactions among variables leads to the conclusion that public attitude towards biodiesel should be seen as a multi-faceted process and should be strongly considered prior to its commercialisation.

  17. Biodiesel production from waste soybean oil biomass as renewable ...

    African Journals Online (AJOL)

    The results showed that biodiesel produced from different oil to methanol ratios, alcohol types and shaking time exhibited considerable differences. There was also a considerable difference of biodiesel yield produced by using methanol, ethanol and 1- butanol. The biodiesel yield increased in the order of 1-butanol ...

  18. Potentials of Microalgae Biodiesel Production in Nigeria | Ogbonna ...

    African Journals Online (AJOL)

    There is high potential for largescale production of biodiesel from microalgae in Nigeria. Establishment of biodiesel production industries in Nigeria will have positive effects on socio-economic development of the country. It has been estimated that Nigeria currently needs about 27 thousand barrels of biodiesel per day to be ...

  19. Base catalyzed transesterification of sunflower oil biodiesel | Ahmad ...

    African Journals Online (AJOL)

    In this study, sunflower oil was investigated for biodiesel production. Sunflower is one of the leading oil seed crop, cultivated for the production of oil in the world. It has also been considered as an important crop for biodiesel production. Seeds for biodiesel production were procured from local farmers of Attock and ...

  20. Systematic sustainable process design and analysis of biodiesel processes

    DEFF Research Database (Denmark)

    Mansouri, Seyed Soheil; Ismail, Muhammad Imran; Babi, Deenesh Kavi

    2013-01-01

    Biodiesel is a promising fuel alternative compared to traditional diesel obtained from conventional sources such as fossil fuel. Many flowsheet alternatives exist for the production of biodiesel and therefore it is necessary to evaluate these alternatives using defined criteria and also from...... a biodiesel production case study....

  1. Increasing the extraction efficiency of algal lipid for biodiesel ...

    African Journals Online (AJOL)

    SAM

    2014-04-09

    Apr 9, 2014 ... for production of hydrogen, methane, vegetable oils. (triglycerides, for biodiesel), hydrocarbons and ethanol. The high calorific value lipids generated by the micro- algae and cyanobacteria are used for biodiesel (Illman et al., 2000). A mechanism that could concept-tually scale- up the yield of biodiesel ...

  2. Economic feasibility of biodiesel production from Macauba in Brazil

    International Nuclear Information System (INIS)

    Lopes, Daniela de Carvalho; Steidle Neto, Antonio José; Mendes, Adriano Aguiar; Pereira, Débora Tamires Vítor

    2013-01-01

    In this work the economic feasibility of biodiesel production in Brazil by using the Macauba oil as raw matter is studied. The software SIMB-E, in which a cash flow model applied to biodiesel production is implemented, was used during simulations. Economic indexes related to biodiesel production features, as well as the competitiveness between selling prices of biodiesel and petrodiesel were considered. It was found that all of the 8 simulated scenarios were potentially profitable, but only 2 of them presented competitive biodiesel selling prices, being considered as worthwhile projects. These were seed-oil plants with alkaline transesterification. Results also indicated that the success of biodiesel production still requires additional revenues beyond that derived from biodiesel itself, including income from the feedstock coproducts and glycerol. Macauba showed to be a potential crop to be used in biodiesel production. However, the domestication and improvement on processing of this species are indispensable to ensure its availability of long-term use. - Highlights: • Competitiveness between selling prices of biodiesel and petrodiesel was the main evaluated criterion. • The main criterion to suggest worthwhile projects was the biodiesel selling price. • Biodiesel plants with integrated oil mill and alkaline transesterification were profitable. • Macauba showed to be a potential crop to be used in biodiesel production. • The domestication and improvement on processing of Macauba are indispensable

  3. BiodieselFAO: An Integrated Decision Support System for Investment Analysis in the Biodiesel Production Chain

    Directory of Open Access Journals (Sweden)

    Aziz Galvão da Silva Júnior

    2015-06-01

    Full Text Available In the short and medium terms, biofuels are the most viable alternative to reduce the environmental impact of fossil fuels. The recent controversy over the competition between biofuels and food production increases the complexity of investment decisions in the biodiesel production chain. In this context, decision support tools are highly relevant. The purpose of this article is to describe the BiodieselFAO using the Unified Modeling Language (UML. An integrated analysis considering both agricultural and industrial sectors was identified as a key requirement to the system. Therefore, farmers and industry are the main actors in the use case diagram. As the raw material represents around 70% of the industrial cost of biodiesel production, the price negotiation of raw material (oilseeds is the central use case. Configuration, agriculture, industry, results and scenarios are the modules, which encompass the functionalities derived from the UML diagrams. The Food and Agriculture Organization of the United Nations (FAO has made the BiodieselFAO available, free of charge, to around 180 professionals from 17 Latin American countries. Additionally, the developing team has supported the usage of the BiodieselFAO in several biodiesel investment analyses throughout Latin America. The system was also useful in the design and analysis of policy related to biodiesel industry in Brazil.

  4. Sustainable Algae Biodiesel Production in Cold Climates

    Directory of Open Access Journals (Sweden)

    Rudras Baliga

    2010-01-01

    Full Text Available This life cycle assessment aims to determine the most suitable operating conditions for algae biodiesel production in cold climates to minimize energy consumption and environmental impacts. Two hypothetical photobioreactor algae production and biodiesel plants located in Upstate New York (USA are modeled. The photobioreactor is assumed to be housed within a greenhouse that is located adjacent to a fossil fuel or biomass power plant that can supply waste heat and flue gas containing CO2 as a primary source of carbon. Model results show that the biodiesel areal productivity is high (19 to 25 L of BD/m2/yr. The total life cycle energy consumption was between 15 and 23 MJ/L of algae BD and 20 MJ/L of soy BD. Energy consumption and air emissions for algae biodiesel are substantially lower than soy biodiesel when waste heat was utilized. Algae's most substantial contribution is a significant decrease in the petroleum consumed to make the fuel.

  5. Environmental accounting of biodiesel from soybeans

    Energy Technology Data Exchange (ETDEWEB)

    Romanelli, T.L. [Escola Superior de Agricultura Luiz de Queiroz (ESALQ/USP), Piracicaba, SP (Brazil). Dept. de Engenharia Rural

    2008-07-01

    As nonrenewable energy sources are depleted globally new sources of energy are becoming necessary. One option that has been explored in recent years is biodiesel production using agricultural products such as soybeans. The emergy accounting method gives value to environmental flows of energy and it quantifies the total amount of energy that has gone in to a product. Also, it provides an inventory of inputs and outputs that can be used to analyze what, if any, types of changes can be made to specific processes within the production as well as improvements in the efficiency of the system as a whole in order to increase the viability of biodiesel as a fuel source. This evaluation uses the concept of emergy to quantify the costs and returns of biodiesel production. This study showed that, currently in the typical production system in the US, biodiesel is not competitive to fossil fuel sources regarding energy providing. But, considering the depletion of the latter source it may become part of source for society. For biodiesel from soybean oil to become more energetically competitive the agricultural production has to be improved since it demands more than 80% of the used resources. Within the soybean production, topsoil loss was responsible for more than 40% which also negatively affects the renewability of this energy source. (author)

  6. Enzymatisk omestring til produktion af biodiesel

    DEFF Research Database (Denmark)

    Fjerbæk, Lene

    2007-01-01

      Biodiesel er i dag sammen med bioethanol et bud på, hvordan transportsektoren kan nedbringe sin netto CO2-emission til atmosfæren og lagrene af fossilt brændstof kan strækkes. På verdensplan forventes der en produktion af biodiesel på 7,9 mio. tons i 2007. Ved den industrielle fremstilling af...... biodiesel benyttes i dag kemiske katalysatorer såsom H2SO4, NaOH, MeONa eller KOH, der efterfølgende fjernes fra den producerede biodiesel med store mængder vand og derved produceres store mængder spildevand. Ved at benytte enzymer i processen kan man reducere mængden af spildevand, der skal renses. Enzymer...... benyttes ikke i de eksisterende processer, men det forventes, at udviklingen af processerne vil øge deres anvendelse i biodieselproduktion. I artiklen præsenteres fordele og ulemper ved anvendelse af enzymer til biodiesel produktion....

  7. Production of biodiesel from Coelastrella sp. microalgae

    Science.gov (United States)

    Mansur, Dieni; Fitriady, Muhammad Arifuddin; Susilaningsih, Dwi; Simanungkalit, Sabar Pangihutan

    2017-11-01

    Microalgae have a wide area of usage and one of them it can be used for biodiesel production. In biodiesel production, lipids containing triglyceride or free fatty acid are converted into methyl ester through trans/esterification reactions. Lipids from microalgae can be extracted by acetone and dimethyl carbonate using homogenizer. Esterification of the lipids was investigated using various catalysts and source of methyl group. Activity of homogeneous catalyst such as HCl and H2SO4 and heterogeneous catalysts such as montmorillonit K-10 and ledgestone was investigated. Moreover, methanol and dimethyl carbonate as source of methyl group were also studied. Among of catalysts with methanol as source of methyl group, it was found that yield of crude biodiesel derived from Choelestrella Sp. microalgae was high over H2SO4 catalyst. On the other hand, over H2SO4 catalyst using dimethyl carbonate as source of methyl group, yield of crude biodiesel significant increase. However, FAME composition of crude biodiesel was high over HCl catalyst.

  8. Mixotrophic cultivation of microalgae for biodiesel production: status and prospects.

    Science.gov (United States)

    Wang, Jinghan; Yang, Haizhen; Wang, Feng

    2014-04-01

    Biodiesel from microalgae provides a promising alternative for biofuel production. Microalgae can be produced under three major cultivation modes, namely photoautotrophic cultivation, heterotrophic cultivation, and mixotrophic cultivation. Potentials and practices of biodiesel production from microalgae have been demonstrated mostly focusing on photoautotrophic cultivation; mixotrophic cultivation of microalgae for biodiesel production has rarely been reviewed. This paper summarizes the mechanisms and virtues of mixotrophic microalgae cultivation through comparison with other major cultivation modes. Influencing factors of microalgal biodiesel production under mixotrophic cultivation are presented, development of combining microalgal biodiesel production with wastewater treatment is especially reviewed, and bottlenecks and strategies for future commercial production are also identified.

  9. Biodiesel as a motor fuel price stabilization mechanism

    International Nuclear Information System (INIS)

    Serra, Teresa; Gil, José M.

    2012-01-01

    This article studies the capacity of biofuels to reduce motor fuel price fluctuations. For this purpose, we study dependence between crude oil and biodiesel blend prices in Spain. Copula models are used for this purpose. Results suggest that the practice of blending biodiesel with diesel can protect consumers against extreme crude oil price increases. - Highlights: ► We study the capacity of biofuels to reduce fuel price fluctuations. ► We focus on Spanish biodiesel market. ► Biodiesel and crude oil price dependence is studied using copula functions. ► Biodiesel can protect consumers against extreme crude oil price increases.

  10. Biodiesel Basics (Spanish Version); Clean Cities, Energy Efficiency & Renewable Energy (EERE)

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-08-01

    This Spanish-language fact sheet provides a brief introduction to biodiesel, including a discussion of biodiesel blends, which blends are best for which vehicles, where to buy biodiesel, how biodiesel compares to diesel fuel in terms of performance, how biodiesel performs in cold weather, whether biodiesel use will plug vehicle filters, how long-term biodiesel use may affect engines, biodiesel fuel standards, and whether biodiesel burns cleaner than diesel fuel. The fact sheet also dismisses the use of vegetable oil as a motor fuel.

  11. Energy aspects of microalgal biodiesel production

    Directory of Open Access Journals (Sweden)

    Edith Martinez-Guerra

    2016-03-01

    Full Text Available Algal biodiesel production will play a significant role in sustaining future transportation fuel supplies. A large number of researchers around the world are investigating into making this process sustainable by increasing the energy gains and by optimizing resource-utilization efficiencies. Although, research is being pursued aggressively in all aspects of algal biodiesel production from microalgal cell cultivation, cell harvesting, and extraction and transesterification steps to the final product separation and purification, there is a large disparity in the data presented in recent reports making it difficult to assess the real potential of microalgae as a future energy source. This article discusses some of the key issues in energy consumption in the process of algal biodiesel production and identifies the areas for improvement to make this process energy-positive and sustainable.

  12. Valorization of crude glycerol from biodiesel production

    Directory of Open Access Journals (Sweden)

    Konstantinović Sandra S.

    2016-01-01

    Full Text Available The increased production of biodiesel as an alternative fuel involves the simultaneous growth in production of crude glycerol as its main by-product. Therefore, the feasibility and sustainability of biodiesel production requires the effective utilization of crude glycerol. This review describes various uses of crude glycerol as a potential green solvent for chemical reactions, a starting raw material for chemical and biochemical conversions into value-added chemicals, a substrate or co-substrate in microbial fermentations for synthesis of valuable chemicals and production of biogas and biohydrogen as well as a feedstuff for animal feed. A special attention is paid to various uses of crude glycerol in biodiesel production. [Projekat Ministarstva nauke Republike Srbije, br. III 45001

  13. Isothermal calorimetry on enzymatic biodiesel production

    DEFF Research Database (Denmark)

    Fjerbæk, Lene

    2008-01-01

    information about effects taking place when using lipases immobilized on an inert carrier for transesterification of a triglyceride and an alcohol as for biodiesel production. The biodiesel is produced by rapeseed oil and methanol as well as ethanol and a commercial biocatalyst Novozym 435 from Novozymes......Calorimetric investigations are very useful for real-time monitoring of reaction rate and heat. Various chemical and physical effects can be revealed and observed closely such as adsorption, mixing, evaporation, stirring and chemical reactions during a calorimetric experiment. For enzymatic...... containing a Candida Antarctica B lipase immobilized on an acrylic resin. The reaction investigated is characterized by immiscible liquids (oil, methanol, glycerol and biodiesel) and enzymes imm. on an inert carrier during reaction, which allows several effects to take place that during normal reaction...

  14. Perspectives on biodiesel as a sustainable fuel

    Energy Technology Data Exchange (ETDEWEB)

    Janaun, Jidon [Department of Chemical and Biological Engineering, University of British Columbia, 2360 East Mall, Vancouver, BC (Canada); Chemical Engineering Programme, School of Engineering and Information Technology, Universiti Malaysia Sabah, 88999 Kota Kinabalu, Sabah (Malaysia); Ellis, Naoko [Department of Chemical and Biological Engineering, University of British Columbia, 2360 East Mall, Vancouver, BC (Canada)

    2010-05-15

    The present global economy downturn affects every corner of the world including the vehicular fuel industry. This paper highlights some of the perspectives for the biodiesel industry to thrive as an alternative fuel, while discussing benefits and limitations of biodiesel. This includes the improvement of the conversion technology to achieve a sustainable process at cheaper cost, environmentally benign and cleaner emissions, diversification of products derived from glycerol, and policy and government incentives. More specifically, an overview is given on making the production process more economical by developing high conversion and low cost catalysts from renewable sources, and utilizing waste oil as feedstock. Further emphasis is given on the need for public education and awareness for the use and benefits of biodiesel, while promoting policies that will not only endorse the industry, but also promote effective land management. (author)

  15. Environmental Sustainability Analysis of Biodiesel Production

    DEFF Research Database (Denmark)

    Herrmann, Ivan Tengbjerg; Hauschild, Michael Michael Zwicky; Birkved, Morten

    like these require a life cycle perspective on the biofuel - from the cradle (production of the agricultural feedstock) to the grave (use as fuel). An environmental life cycle assessment is performed on biodiesel to compare different production schemes including chemical and enzymatic esterification...... with the use of methanol or ethanol. The life cycle assessment includes all processes needed for the production, distribution and use of the biodiesel (the product system), and it includes all relevant environmental impacts from the product system, ranging from global impacts like climate change and loss...... of non-renewable resources over regional impacts like acidification, eutrophication and photochemical ozone to more local impacts like ecotoxicity and physical impacts like land use, to allow judging on the overall environmental sustainability of the biodiesel and to support identification of the main...

  16. [Studies of enzymatic synthesis of biodiesel].

    Science.gov (United States)

    Deng, Li; Tan, Tian-Wei; Wang, Fang

    2003-01-01

    Biodiesel, an alternative diesel fuel, fatty acid alkyl ester, is made from renewable biological sources such as vegetable oils and animal fats. Two processes for biodiesel synthesis, enzymatic lipase catalytic esterification from fatty acid and transesterification from oils and fats, was investigated. The effects of various lipases, enzyme amount and purity, solvent, water absorbent, inhibition of short chains alcohol, specificity of substrate, molar ratio of substrate on esterification were studied in detail. The esterification degree with the optimal parameter and process can reach up to 92%. The purity of biodiesel obtained by separation and purification is up to 98%, and the half-life of the immobilized lipase for the esterification process can be up to 360hr, Moreover, the preliminary studies of the transesterification including the amount of methanol and mode of adding methanol into reaction system were made. The transesterification degree with adding methanol stepwise can reach 83%.

  17. Improvement of biodiesel methanol blends

    Directory of Open Access Journals (Sweden)

    Y. Datta Bharadwaz

    2016-06-01

    Full Text Available The main objective of this work was to improve the performance of biodiesel–methanol blends in a VCR engine by using optimized engine parameters. For optimization of the engine, operational parameters such as compression ratio, fuel blend, and load are taken as factors, whereas performance parameters such as brake thermal efficiency (Bth and brake specific fuel consumption (Bsfc and emission parameters such as carbon monoxide (CO, unburnt hydrocarbons (HC, Nitric oxides (NOx and smoke are taken as responses. Experimentation is carried out as per the design of experiments of the response surface methodology. Optimization of engine operational parameters is carried out using Derringers Desirability approach. From the results obtained it is inferred that the VCR engine has maximum performance and minimum emissions at 18 compression ratio, 5% fuel blend and at 9.03 kg of load. At this optimized operating conditions of the engine the responses such as brake thermal efficiency, brake specific fuel consumption, carbon monoxide, unburnt hydrocarbons, nitric oxide, and smoke are found to be 31.95%, 0.37 kg/kW h, 0.036%, 5 ppm, 531.23 ppm and 15.35% respectively. It is finally observed from the mathematical models and experimental data that biodiesel methanol blends have maximum efficiency and minimum emissions at optimized engine parameters.

  18. Improving the low temperature properties of biodiesel fuel

    Energy Technology Data Exchange (ETDEWEB)

    Bhale, Purnanand Vishwanathrao; Deshpande, Nishikant V.; Thombre, Shashikant B. [Visvesvaraya National Institute of Technology, Mechanical Engineering, South Ambazari Road, Near Bajaj Nagar, 440011 Nagpur, Maharashtra (India)

    2009-03-15

    The use of biodiesel as a diesel fuel extender and lubricity improver is rapidly increasing. While most of the properties of biodiesel are comparable to petroleum based diesel fuel, improvement of its low temperature flow characteristic still remains one of the major challenges when using biodiesel as an alternative fuel for diesel engines. The biodiesel fuels derived from fats or oils with significant amounts of saturated fatty compounds will display higher cloud points and pour points. This paper is aimed to investigate the cold flow properties of 100% biodiesel fuel obtained from Madhuca indica, one of the important species in the Indian context. In this paper, the cold flow properties of biodiesel were evaluated with and without pour point depressants towards the objectives of identifying the pumping and injecting of these biodiesel in CI engines under cold climates. Effect of ethanol, kerosene and commercial additive on cold flow behavior of this biodiesel was studied. A considerable reduction in pour point has been noticed by using these cold flow improvers. The performance and emission with ethanol blended Mahua biodiesel fuel and ethanol-diesel blended Mahua biodiesel fuel have also been studied. A considerable reduction in emission was obtained. Ethanol blended biodiesel is totally a renewable, viable alternative fuel for improved cold flow behavior and better emission characteristics without affecting the engine performance. (author)

  19. Microbial degradation of palm (Elaeis guineensis biodiesel

    Directory of Open Access Journals (Sweden)

    Giselle Lutz

    2006-03-01

    Full Text Available The kinetics of biodegradation of palm-derived fatty methyl and ethyl esters (Elaeis guineensis biodiesel by a wild-type aerobic bacterial population was measured at 20 °C, as the rate of oxygen uptake by a manometric technique. The methyl and ethyl biodiesels were obtained by potassium-hydroxide catalysed transesterification of palm oil, respectively. The bacterial flora included the genera Bacillus, Proteus, Pseudomonas, Citrobacter and Enterobacter. The rate of oxygen uptake for palm biodiesel is similar to the quantity observed in the biodegradation of 1.0 mM solutions of simple substrates such as carbohydrates or amino acids.Palm methyl or ethyl biodiesel is subjected to facile aerobic biodegradation by wild-type bacteria commonly present in natural open environments. This result should lessen any environmental concern for its use as alternative fuel, solvent or lubricant. Rev. Biol. Trop. 54(1: 59-63.Epub 2006 Mar 31.La cinética de la biodegradación de los ésteres metílicos y etílicos derivados de palma (biodiesel por una población silvestre de bacterias aeróbicas fue medida a 20 °C, como medición manométrica del consumo de oxígeno. Los ésteres metílicos y etílicos se obtuvieron por transesterificación del aceite de palma con metanol y etanol,respectivamente. La flora bacteriana incluyó a los géneros Bacillus, Proteus, Pseudomonas, Citrobacter y Enterobacter. Las velocidades de consumo de oxígeno para las muestras de biodiesel fueron similares a lo observado en la biodegradación de disoluciones 1.0 mM de sustratos sencillos solubles en agua, tales como carbohidratos, aminoácidos y albúmina de huevo.

  20. Anaerobic Biodegradation of soybean biodiesel and diesel blends under sulfate-reducing conditions

    Science.gov (United States)

    Biotransformation of soybean biodiesel and its biodiesel/petrodiesel blends were investigated under sulfate-reducing conditions. Three blends of biodiesel, B100, B50, and B0, were treated using microbial cultures pre-acclimated to B100 (biodiesel only) and B80 (80% biodiesel and ...

  1. Algal biodiesel economy and competition among bio-fuels.

    Science.gov (United States)

    Lee, D H

    2011-01-01

    This investigation examines the possible results of policy support in developed and developing economies for developing algal biodiesel through to 2040. This investigation adopts the Taiwan General Equilibrium Model-Energy for Bio-fuels (TAIGEM-EB) to predict competition among the development of algal biodiesel, bioethanol and conventional crop-based biodiesel. Analytical results show that algal biodiesel will not be the major energy source in 2040 without strong support in developed economies. In contrast, bioethanol enjoys a development advantage relative to both forms of biodiesel. Finally, algal biodiesel will almost completely replace conventional biodiesel. CO(2) reduction benefits the development of the bio-fuels industry. Copyright © 2010 Elsevier Ltd. All rights reserved.

  2. Isothermal calorimetry of enzymatic biodiesel reaction

    DEFF Research Database (Denmark)

    Fjerbæk Søtoft, Lene; Westh, Peter; Christensen, Knud Villy

    2010-01-01

      Isothermal calorimetry ITC has been used to investigate enzymatic biodiesel production. The transesterification of rapeseed oil with methanol and ethanol was catalyzed by the immobilized lipase Novozym 435 at 40°C. The ITC-experiments clearly demonstrate the possibilities of investigating complex...... and composition change in the system, the heat of reaction at 40°C for the two systems has been determined to -9.8 ± 0.9 kJ/mole biodiesel formed from rapeseed oil and methanol, and - 9.3 ± 0.7 kJ/mole when rapeseed oil and ethanol is used....

  3. Cetane Number of Biodiesel from Karaya Oil

    KAUST Repository

    Wasfi, Bayan

    2017-04-01

    Biodiesel is a renewable fuel alternative to petroleum Diesel, biodiesel has similar characteristic but with lesser exhaust emission. In this study, transesterification of Karaya oil is examined experimentally using a batch reactor at 100-140°C and 5 bar in subcritical methanol conditions, residence time from 10 to 20 minutes, using a mass ratio 6 methanol-to-vegetable oil. Methanol is used for alcoholysis and sodium hydroxide as a catalyst. Experiments varied the temperature and pressure, observing the effect on the yield and reaction time. In addition, biodiesel from corn oil was created and compared to biodiesel from karaya oil. Kinetic model proposed. The model estimates the concentration of triglycerides, diglycerides, monoglycerides and methyl esters during the reaction. The experiments are carried out at temperatures of 100°C and above. The conversion rate and composition of methyl esters produced from vegetable oils are determined by Gas Chromatography Analysis. It was found that the higher the temperature, the higher reaction rate. Highest yield is 97% at T=140°C achieved in 13 minutes, whereas at T=100°C yield is 68% in the same time interval. Ignition Quality Test (IQT) was utilized for determination of the ignition delay time (IDT) inside a combustion chamber. From the IDT cetane number CN inferred. In case of corn oil biodiesel, the IDT = 3.5 mS, leading to a CN = 58. Whereas karaya oil biodiesel showed IDT = 2.4 mS, leading to a CN = 97. The produced methyl esters were also characterized by measurements of viscosity (υ), density (ρ), flash point (FP) and heat of combustion (HC). The following properties observed: For corn biodiesel, υ = 8.8 mPa-s, ρ = 0.863 g/cm3, FP = 168.8 °C, and HC = 38 MJ/kg. For karaya biodiesel, υ = 10 mPa-s, ρ = 0.877 g/cm3, FP = 158.2 °C, and HC = 39 MJ/kg.

  4. Cottonseed oil for biodiesel production; Oleo de algodao para a producao de biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Pighinelli, Anna L.M.T.; Park, Kil J. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil)], E-mail: annalets@feagri.unicamp.br; Ferrari, Roseli A.; Miguel, Ana M.R.O. [Instituto de Tecnologia de Alimentos (ITAL), Campinas, SP (Brazil)], Emails: roseliferrari@ital.sp.gov.br, anarauen@ital.sp.gov.br, kil@feagri.unicamp.br

    2009-07-01

    Crude cottonseed oil is an alternative for biodiesel production, mostly in Mato Grosso State, where its production is the biggest of Brazil. Even being an acid oil, esterification reaction, followed by transesterification, could make possible the biodiesel production. In this study, crude cottonseed oil obtained from expelled process was reacted to evaluate molar ration and catalyst concentration effects in biodiesel yield. Molar ratio varied from 3 to 15 moles of ethanol to 1 mol of oil, and catalyst, from 1 to 5% by oil mass. Statistic analysis showed that none of studied variables was significant, for the values range. Biodiesel yield had a maximum of 88%, for molar ratio of 4.7 and 4.42% of catalyst concentration. A combination of oil with high free fatty acid content and ethanol as alcohol, affected the separation between esters and glycerol. (author)

  5. Bioconversion of biodiesel refinery waste in the bioemulsifier by Trichosporon mycotoxinivorans CLA2

    Directory of Open Access Journals (Sweden)

    de Souza Monteiro Andrea

    2012-05-01

    Full Text Available Abstract Background The microbial bioemulsifiers was surface active compounds, are more effective in stabilizing oil-in-water emulsions. The yeasts have been isolated to produce bioemulsifiers from vegetable oils and industrial wastes. Results Trichosporon mycotoxinivorans CLA2 is bioemulsifier-producing yeast strain isolated from effluents of the dairy industry, with ability to emulsify different hydrophobic substrates. Bioemulsifier production (mg/L and the emulsifying activity (E24 of this strain were optimized by response surface methodology using mineral minimal medium containing refinery waste as the carbon source, which consisted of diatomaceous earth impregnated with esters from filters used in biodiesel purification. The highest bioemulsifier production occurred in mineral minimal medium containing 75 g/L biodiesel residue and 5 g/L ammonium sulfate. The highest emulsifying activity was obtained in medium containing 58 g/L biodiesel refinery residue and 4.6 g/L ammonium sulfate, and under these conditions, the model estimated an emulsifying activity of 85%. Gas chromatography and mass spectrometry analysis suggested a bioemulsifier molecule consisting of monosaccharides, predominantly xylose and mannose, and a long chain aliphatic groups composed of octadecanoic acid and hexadecanoic acid at concentrations of 48.01% and 43.16%, respectively. The carbohydrate composition as determined by GC-MS of their alditol acetate derivatives showed a larger ratio of xylose (49.27%, mannose (39.91%, and glucose (10.81%. 1 H NMR spectra confirmed by COSY suggested high molecular weight, polymeric pattern, presence of monosaccharide’s and long chain aliphatic groups in the bioemulsifier molecule. Conclusions The biodiesel residue is an economical substrate, therefore seems to be very promising for the low-cost production of active emulsifiers in the emulsification of aromatics, aliphatic hydrocarbons, and kerosene.

  6. Exhaust gas emissions and mutagenic effects of modern diesel fuels, GTL, biodiesel and biodiesel blends

    Energy Technology Data Exchange (ETDEWEB)

    Munack, Axel; Ruschel, Yvonne; Schroeder, Olaf [Federal Research Institute for Rural Areas, Forestry and Fisheries, Braunschweig (Germany)], E-mail: axel.munack@vti.bund.de; Krahl, Juergen [Coburg Univ. of Applied Sciences (Germany); Buenger, Juergen [University of Bochum (Germany)

    2008-07-01

    Biodiesel can be used alone (B100) or blended with petroleum diesel in any proportion. The most popular biodiesel blend in the U.S.A. is B20 (20% biodiesel, 80% diesel fuel), which can be used for Energy Policy Act of 1992 (EPAct) compliance. In the European Union, the use of biofuel blends is recommended and was introduced by federal regulations in several countries. In Germany, biodiesel is currently blended as B5 (5% biodiesel) to common diesel fuel. In 2008, B7 plus three percent hydrotreated vegetable oil (HVO) as well is intended to become mandatory in Germany. To investigate the influence of blends on the emissions and possible health effects, we performed a series of studies with several engines (Euro 0, III and IV) measuring regulated and non-regulated exhaust compounds and determining their mutagenic effects. Emissions of blends showed an approximate linear dependence on the blend composition, in particular when regulated emissions are considered. However, a negative effect of blends was observed with respect to mutagenicity of the exhaust gas emissions. In detail, a maximum of the mutagenic potency was found in the range of B20. From this point of view, B20 must be considered as a critical blend, in case diesel fuel and biodiesel are used as binary mixtures. (author)

  7. Thermodegradation of biodiesel: thermoanalytical and rheological characterization; Degradacao termica de biodiesel: caracterizacao termoanalitica e reologica

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Everson L.; Carvalho, Laura H.; Araujo, Gilmar T.; Gadelha, Tatiana S. [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

    2008-07-01

    Brazil is a country of extensive agricultural land and great oil consumption and these factors favor biodiesel production in this country. In order for diesel/biodiesel mixtures to be effectively employed in diesel engines, a rigid quality control of these mixtures is needed. Biodiesel and mixtures must have their quality monitored with respect to oxidative resistance, thermal stability, fluidity and volatility, properties which can be modified by the adverse transport and stock conditions prior to consumption. Oxidation is the main degradation mechanism of products under transport and stock conditions, which can lead to significant economical losses. In this work sought the thermal degradation of neat biodiesel, synthesized in our laboratories was monitored. Thermal aging was conducted at 210 deg C for up to 1000 h. Virgin and thermally degraded samples were characterized by rheological measurements (in different shear conditions); FTIR; density and by color changes. We concluded that the soy biodiesel was successfully synthesized and that thermal exposure caused thermal-oxidative degradation of the biodiesel sample, significantly changing its properties as a function of thermal exposure times. (author)

  8. KINETIKA TRANSESTERIFIKASI BIODIESEL JARAK PAGAR

    Directory of Open Access Journals (Sweden)

    Buchori Luqman

    2012-07-01

    Full Text Available Biodiesel were produced by trans-etherification of castor oil with alcohol in the presence of NaOH catalyst. Thereaction mechanism and model of castor oil trans-etherification isA + 3B C + 3 DA, B, C, and D were castor oil, alcohol, glycerol, and ester. The reaction rate equation was r=-dCA/dt =k1(CA(CB3–k2(CC(CD3. In this study was used two measurement method of free fat acid as the rest content ofcastor oil with SNI 01-3555-1998 and AOAC (Association of Analytical Chemist. It found that SNI 01-3555-1998 method was the easier and the acurate measurement. The classification of alcohol used was methanol andethanol to compare the action both of them. Methanol produces the higher conversion than ethanol. The reactionin a batch reactor with temperature 40, 50, and 60°C in atmospheric pressure as the operation condition tolooking for kinetics parameter of trans-etherification. Coefficient reaction rate and activation energy were lookinto kinetics study. Reaction rate was a mathematics model as a function of concentration and time which solvedby Runge-Kutta, multivariable optimization and SSE (some square error method using Matlab. The activationenergy (Ea and impact factor (A obtained by linier regression method. The result of study obtained the kineticsparameter of trans-etherification with methanol k1=1.9313x1031exp (-41.940/RT average error 0.0010 andk2=2.7678x1025exp(-37.362/ RT average error 0.0003. While kinetics parameter of trans-etherification withethanol obtained k1=1.168x1019exp(-24.588/ RT average error 0.0306 and k2=4.9966x106exp(-10.328/RTaverage error 0.1589. It means, more reactive alcohol then bigger the value of kinetics parameter.

  9. Biodiesel waste products as soil amendments : evaluation of microbial, biological, and plant toxicity.

    Science.gov (United States)

    2011-10-22

    During biodiesel production, about 200 lbs of glycerol, commonly called glycerin, is produced for every 1 ton of biodiesel. As the : biodiesel industry grows, so does the need to dispose of this waste product. While potential uses for glycerin exist,...

  10. Biodiesel generation from oleaginous yeast Rhodotorula glutinis ...

    African Journals Online (AJOL)

    SERVER

    2007-09-19

    Sep 19, 2007 ... This study explored a strategy to convert agricultural and forestry residues into microbial lipid, which could be further transformed into biodiesel. Among the 250 yeast strains screened for xylose assimilating capacity, eight oleaginous yeasts were selected by Sudan Black B test. The lipid content of these 8 ...

  11. Jatropha bio-diesel production and use

    International Nuclear Information System (INIS)

    Achten, W.M.J.; Verchot, L.; Franken, Y.J.; Mathijs, E.; Singh, V.P.; Aerts, R.; Muys, B.

    2008-01-01

    The interest in using Jatropha curcas L. (JCL) as a feedstock for the production of bio-diesel is rapidly growing. The properties of the crop and its oil have persuaded investors, policy makers and clean development mechanism (CDM) project developers to consider JCL as a substitute for fossil fuels to reduce greenhouse gas emissions. However, JCL is still a wild plant of which basic agronomic properties are not thoroughly understood and the environmental effects have not been investigated yet. Gray literature reports are very optimistic on simultaneous wasteland reclamation capability and oil yields, further fueling the Jatropha bio-diesel hype. In this paper, we give an overview of the currently available information on the different process steps of the production process of bio-diesel from JCL, being cultivation and production of seeds, extraction of the oil, conversion to and the use of the bio-diesel and the by-products. Based on this collection of data and information the best available practice, the shortcomings and the potential environmental risks and benefits are discussed for each production step. The review concludes with a call for general precaution and for science to be applied

  12. Assessment of indigenous bacteria from biodiesel effluents ...

    African Journals Online (AJOL)

    This study was conducted in order to identify indigenous microorganisms which have the capability to degrade biodiesel contaminated sites. Bacterial isolates were identified on the basis of morphological and biochemical characterization in which nine bacteria were isolated from the site, Staphylococcus aureus and ...

  13. Biodiesel Production Technology: August 2002--January 2004

    Energy Technology Data Exchange (ETDEWEB)

    Van Gerpen, J.; Shanks,B.; Pruszko,R.; Clements, D.; Knothe, G.

    2004-07-01

    Biodiesel is an alternative fuel for diesel engines that is gaining attention in the United States after reaching a considerable level of success in Europe. The purpose of this book is to describe and explain the process and issues involved in producing this fuel.

  14. WI Biodiesel Blending Progream Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Redmond, Maria E; Levy, Megan M

    2013-04-01

    The Wisconsin State Energy Office's (SEO) primary mission is to implement cost effective, reliable, balanced, and environmentally friendly clean energy projects. To support this mission the Wisconsin Biodiesel Blending Program was created to financially support the installation infrastructure necessary to directly sustain biodiesel blending and distribution at petroleum terminal facilities throughout Wisconsin. The SEO secured a federal directed award of $600,000 over 2.25 years. With these funds, the SEO supported the construction of inline biodiesel blending facilities at two petroleum terminals in Wisconsin. The Federal funding provided through the state provided a little less than half of the necessary investment to construct the terminals, with the balance put forth by the partners. Wisconsin is now home to two new biodiesel blending terminals. Fusion Renewables on Jones Island (in the City of Milwaukee) will offer a B100 blend to both bulk and retail customers. CITGO is currently providing a B5 blend to all customers at their Granville, WI terminal north of the City of Milwaukee.

  15. Evaluation of Physicochemical Properties of Biodiesel Produced ...

    African Journals Online (AJOL)

    The non-edible vegetable oils of Jatropha curcas, neem, castor, rubber and edible oils of soyabean and cotton were investigated for their use as biodiesel feedstock. The analysis of different oil properties, fuel properties of non-edible and edible vegetable oils were investigated in detail. A two-step and transesterification ...

  16. Uncertainties in the Bidirectional Biodiesel Supply Chain

    NARCIS (Netherlands)

    Bot, Pieter; van Donk, Dirk Pieter; Pennink, Bartjan; Simatupang, Togar M.

    2015-01-01

    For remote areas, small-scale local biodiesel production is particularly attractive if producers and consumers are the same. Such supply chains are labeled as bidirectional. However, little is known on how raw material supply, transportation, logistics, production and operations uncertainties impact

  17. Biodiesel Technical Update for Purdue Road School

    OpenAIRE

    Howell, Steve; Calvin, Mick

    2017-01-01

    Biodiesel is endorsed by all major diesel engine manufacturers and continues to change the landscape as an alternative to conventional diesel fuel. Its usage and demand are on the rise because of EPA regulations and the fact that it is better for the environment and reduces our demand for hydrocarbon fossil fuels. Join us to learn more about this clean-burning fuel.

  18. Sustainable biodiesel production by catalytic reactive distillation

    NARCIS (Netherlands)

    Kiss, A.A.; Rothenberg, G.

    2008-01-01

    This chapter outlines the properties of biodiesel as renewable fuel, as well as the problems associated with its conventional production processes. The synthesis via fatty acid esterification using solid acid catalysts is investigated. The major challenge is finding a suitable catalyst that is

  19. Lipases as biocatalysts for biodiesel production

    Directory of Open Access Journals (Sweden)

    Ognjanović Nevena D.

    2010-01-01

    Full Text Available Lipases can be used for a variety of biotechnological applications: synthesis of fine chemicals, therapeutics, agrochemicals, cosmetics, flavors, biopolymers and biodiesel. Biodiesel is an alternative fuel for diesel engines that is environmentally acceptable. Conventionally, biodiesel is produced by transesterification of triglycerides and short chain alcohols in the presence of an acid or an alkaline catalyst. There are several problems associated with this kind of production that can be resolved by using lipase as the biocatalyst. The usage of lipases has several advantages over the conventional chemical methods. It is considered as less energy intensive and environmentally friendly. However, there are two main obstacles associated with the effective utilization of lipases in the production of biodiesel. The main one is the cost of the enzyme and its poor stability in the presence of excess alcohol. Several strategies are proposed to overcome these drawbacks: immobilization of lipases, stepwise addition of alcohol, and the usage of novel acyl acceptors and the usage of whole cell biocatalysts.

  20. Room temperature synthesis of biodiesel using sulfonated ...

    Science.gov (United States)

    Sulfonation of graphitic carbon nitride (g-CN) affords a polar and strongly acidic catalyst, Sg-CN, which displays unprecedented reactivity and selectivity in biodiesel synthesis and esterification reactions at room temperature. Prepared for submission to Royal Society of Chemistry (RSC) journal, Green Chemistry as a communication.

  1. Biodiesel intercity passenger rail revenue service test.

    Science.gov (United States)

    2013-10-01

    Amtrak, with the support of the Federal Railroad Administration, operated a P-32 passenger locomotive in revenue service for a : period of 12 months, on a blend of 20 percent pure biodiesel and 80 percent #2 ultra-low sulfur diesel (ULSD) fuel. The G...

  2. Novel polymeric products derived from biodiesel

    Science.gov (United States)

    Biodiesel (produced by reacting a triglyceride with an alcohol) is increasingly being used as diesel fuel and heating oil, especially in Europe. Because of its availability and favorable environmental profile, it may be useful as a renewable feedstock for new polymers. In this work we introduced t...

  3. Hydrotreatment of Oils and Fats for Biodiesel

    DEFF Research Database (Denmark)

    Madsen, Anders Theilgaard; Riisager, Anders; Fehrmann, Rasmus

    The use of renewable biofuels in the transport sector represents an important step towards a sustainable society. Biodiesel is currently produced by the transesterification of fats and oils with methanol, but another viable method could be reaction of the feedstock with H2 to produce long...

  4. Biodiesel's Characteristics Preparation from Palm Oil

    Directory of Open Access Journals (Sweden)

    Tilani Hamid

    2010-10-01

    Full Text Available Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio = 5 : 1, amount of NaOH used as catalyst = 3.5 gr, 4.5 gr, 5 gr and 5.5 gr and it takes about one hour time reaction. The ester (metil ester produced are separated from glycerin and washed until it takes normal pH (6-7 where more amount of catalyst used will decrease the ester (biodiesel produced. The results show that biodiesels' properties made by using 3.5 (M3.5 gr, 4.5 gr (M4.5 and 5 (M5.0 gr catalyst close to industrial diesel oil and the other (M5.5 closes to automotive diesel oil, while blending diesel oil with 20 % biodiesel (B20 is able to improve the diesel engine performances.

  5. ANALYSIS OF COCONUT ETHYL ESTER (BIODIESEL) AND ...

    African Journals Online (AJOL)

    The effect of biodiesel and its blends synthesized from coconut oil (CNO) via alkali catalyzed transeterification on the key fuel properties and corrosion characteristics of copper were investigated. The transesterification of the CNO via ethanol in the presence of potassium hydroxide was performed and the resulting coconut ...

  6. Determination of optimum growth conditions and biodiesel ...

    African Journals Online (AJOL)

    ... exposure time (during the 90 min). The results of the experiment on the effect of simultaneous exposure to sunlight and CO2 for certain times daily, for 25 days, show that the growth rate is directly proportional to the increase of sunlight and CO2 exposure time. Key words: Algal oil, biodiesel, transesterification, glycerine.

  7. Blending Biodiesel in Fishing Boat Fuels for Improved Fuel Characteristics

    International Nuclear Information System (INIS)

    Lin, Cherng-Yuan

    2014-01-01

    Biodiesel is a renewable, clean, alternative energy source with advantages, such as excellent lubricity, superior biodegradability, and high combustion efficiency. Biodiesel is considered for mixing with fishing boat fuels to adjust their fuel characteristics so that toxic pollutants and greenhouse-effect gas emissions from such shipping might be reduced. The effects of blending fishing boat fuels A and B with various weight proportions of biodiesel are experimentally investigated in this study. The results show that biodiesel blending can significantly improve the inferior fuel properties of both fishing boat fuels and particularly fuel B. The flash points of both of these fuels increases significantly with the addition of biodiesel and thus enhances the safety of transporting and storing these blended fuels. The flash point of fishing boat fuel B even increases by 16% if 25 wt.% biodiesel is blended. The blending of biodiesel with no sulfur content is found to be one of the most effective ways to reduce the high sulfur content of fishing boat fuel, resulting in a reduction in the emission of sulfur oxides. The addition of only 25 wt.% biodiesel decreased the sulfur content of the fishing boat fuel by 37%. The high kinematic viscosity of fishing boat fuel B was also observed to be reduced by 63% with the blending of just 25 wt.% biodiesel. However, biodiesel blending caused a slight decrease in heating value around 1–4.5%.

  8. Critical review of jatropha biodiesel promotion policies in India

    International Nuclear Information System (INIS)

    Kumar, Sunil; Chaube, Alok; Jain, Shashi Kumar

    2012-01-01

    Jatropha, a non-edible oil seed yielding plant has been identified by the Government of India to produce biodiesel under National Biodiesel Mission. Failure of phase-I of National Biodiesel Mission and likely failure of phase-II requires critical analysis of policy frameworks related to its long term sustainability. Indian biofuel promotion policies like Biodiesel Purchase Policy and National Biofuel Policy have failed to yield any visible results. No tangible ground work is visible as of now to ensure success of various government plans and policies related to adoption of jatropha biodiesel. It is clearly evident that some serious bottlenecks are delaying the adoption of jatropha biodiesel. Present work identifies important policy bottlenecks like availability of land, non-remunerative pricing policy and state fear relating to loss of revenue in the case of zero duty regimes. This paper attempts to explore and critically analyze present policies and possible options taking into account the recent Indian experiences for successful adoption of jatropha biodiesel. - Highlights: ► Wrong waste land estimates for jatropha has failed Biodiesel Mission. ► No redressal of technological problems with biodiesel usage. ► Present estimated costing of jatropha biodiesel is Rs. 46.45 per liter. ► Promotion of any biofuel needs central government assistance to the states. ► Targets under National Biofuel Policy are also unlikely to be met.

  9. Mackerel biodiesel production from the wastewater containing fish oil

    International Nuclear Information System (INIS)

    Wu, Y.P.; Huang, H.M.; Lin, Y.F.; Huang, W.D.; Huang, Y.J.

    2014-01-01

    Marine fish such as mackerel are important for coastal fisheries in Taiwan. Nearly 60,000 tons of mackerel are produced in Suao, I-lan, Taiwan every year. In this study, oil from the discarded parts of mackerel fish contained in wastewater stream were used as the raw material to produce biodiesel through transesterification reaction. The major fuel properties of MB (mackerel biodiesel), including the iodine value, dynamic viscosity, flash point, and heat value, were determined and compared with sunflower seed oil methyl ester (SFM), JCB (Jatropha curcas biodiesel), and premium diesel (D). MB had a higher iodine value, dynamic viscosity, density, and flash point, but a lower heat value, than did D. MB was also used as fuel in a regular diesel engine to verify its emission characteristics. The MB fuel used for exhaust emission test included pure MB (MB100) and a 20% MB blend with premium diesel (MB20). The exhaust emission of MB was also compared with the exhaust emissions of D and JCB. The results showed that MB20 provided a significant reduction in NO, NO x , and SO 2 emissions under varied engine loads, and required no engine modification. - Highlights: • Biodiesel was produced from wastewater containing mackerel fish oil. • Mackerel biodiesel is compared with Jatropha biodiesel and sunflower seed biodiesel. • MBE (mackerel biodiesel) was found to contain higher amount of unsaturated fatty acids. • Mackerel biodiesel, diesel, and Jatropha biodiesel emissions are compared

  10. Profitability and sustainability of small - medium scale palm biodiesel plant

    Science.gov (United States)

    Solikhah, Maharani Dewi; Kismanto, Agus; Raksodewanto, Agus; Peryoga, Yoga

    2017-06-01

    The mandatory of biodiesel application at 20% blending (B20) has been started since January 2016. It creates huge market for biodiesel industry. To build large-scale biodiesel plant (> 100,000 tons/year) is most favorable for biodiesel producers since it can give lower production cost. This cost becomes a challenge for small - medium scale biodiesel plants. However, current biodiesel plants in Indonesia are located mainly in Java and Sumatra, which then distribute biodiesel around Indonesia so that there is an additional cost for transportation from area to area. This factor becomes an opportunity for the small - medium scale biodiesel plants to compete with the large one. This paper discusses the profitability of small - medium scale biodiesel plants conducted on a capacity of 50 tons/day using CPO and its derivatives. The study was conducted by performing economic analysis between scenarios of biodiesel plant that using raw material of stearin, PFAD, and multi feedstock. Comparison on the feasibility of scenarios was also conducted on the effect of transportation cost and selling price. The economic assessment shows that profitability is highly affected by raw material price so that it is important to secure the source of raw materials and consider a multi-feedstock type for small - medium scale biodiesel plants to become a sustainable plant. It was concluded that the small - medium scale biodiesel plants will be profitable and sustainable if they are connected to palm oil mill, have a captive market, and are located minimally 200 km from other biodiesel plants. The use of multi feedstock could increase IRR from 18.68 % to 56.52 %.

  11. Production and application of biodiesel from waste cooking oil

    Science.gov (United States)

    Tuly, S. S.; Saha, M.; Mustafi, N. N.; Sarker, M. R. I.

    2017-06-01

    Biodiesel has been identified as an alternative and promising fuel source to reduce the dependency on conventional fossil fuel in particular diesel. In this work, waste cooking oil (WCO) of restaurants is considered to produce biodiesel. A well-established transesterification reaction by sodium hydroxide (NaOH) catalytic and supercritical methanol (CH3OH) methods are applied to obtain biodiesel. In the catalytic transesterification process, biodiesel and glycerine are simultaneously produced. The impact of temperature, methanol/WCO molar ratio and sodium hydroxide concentration on the biodiesel formation were analysed and presented. It was found that the optimum 95% of biodiesel was obtained when methanol/WCO molar ratio was 1:6 under 873 K temperature with the presence of 0.2% NaOH as a catalyst. The waste cooking oil blend proportions were 10%, 15%, 20% and 25% and named as bio-diesel blends B-10, B-15, B-20, and B-25, respectively. Quality of biodiesel was examined according to ASTM 6751: biodiesel standards and testing methods. Important fuel properties of biodiesel, such as heating value, cetane index, viscosity, and others were also investigated. A four-stroke single cylinder naturally aspirated DI diesel engine was operated using in both pure form and as a diesel blend to evaluate the combustion and emission characteristics of biodiesel. Engine performance is examined by measuring brake specific fuel consumption and fuel conversion efficiency. The emission of carbon monoxide (CO), carbon dioxide (CO2), nitrogen oxides (NOx), and others were measured. It was measured that the amount of CO2 increases and CO decreases both for pure diesel and biodiesel blends with increasing engine load. However, for same load, a higher emission of CO2 from biodiesel blends was recorded than pure diesel.

  12. Novel process integration for biodiesel blend in membrane reactive divided wall (MRDW) column

    OpenAIRE

    Sakhre Vandana; Jain Sanjeev; Sapkal Vilas S.; Agarwal Dev P.

    2016-01-01

    The paper proposes a novel process integration for biodiesel blend in the Membrane assisted Reactive Divided Wall Distillation (MRDW) column. Biodiesel is a green fuel and grade of biodiesel blend is B20 (%) which consist of 20% biodiesel and rest 80% commercial diesel. Instead of commercial diesel, Tertiary Amyl Ethyl Ether (TAEE) was used as an environment friendly fuel for blending biodiesel. Biodiesel and TAEE were synthesized in a pilot scale reactive distillation column. Dual reactive d...

  13. BIODIESELS AS A FUNCTION OF ENVIRONMENTAL PROTECTION

    Directory of Open Access Journals (Sweden)

    Lovro Babić

    2013-04-01

    Full Text Available As of July 1st 2013. the Republic of Croatia will be a member of the European Union, which will primarily bring necessary harmonisation of ecological standards and requirements. Biodiesel, as a renewable source of energy, can be produced from algae, vegetable oil, and animal fats, and thus it is biodegradable. Biodiesel in Croatia is mainly produced from oilseed rape which, as an agricultural plant, has an increasing share in the past three years and records positive trends. This paper analyses the trend of production in the Republic of Croatia, and compares it with the production and consumption of fossil fuels. On the grounds of Croatia’s favourable agriculture-related climatic characteristics, in particular in the region of Slavonija and Baranja, more intense exploitation of farm land under the cultures intended for biodiesel production can be organised aiming at bumper yield and production. Croatia has already harmonised its standards of production of biodiesel, and by 2020 the consumption of biodiesel is bound to reach 20%. The data used in this paper are obtained from the sources available by Croatian Institute of Statistics, Market Information System in Agriculture, as well as Eurostat, and the rest used here are translated from the sources in the English language. The reviewed are the surfaces planted with oilseed rape in the period between 2007. and 2011., an average yield, and overall production. On the grounds of available information, the calculations of the quantity of bio fuel to be consumed in Croatia by 2020. and the percentage of the land surfaces planted with oilseed rape have been made.

  14. Influence of biodiesel blending on physicochemical properties and importance of mathematical model for predicting the properties of biodiesel blend

    International Nuclear Information System (INIS)

    Wakil, M.A.; Kalam, M.A.; Masjuki, H.H.; Atabani, A.E.; Rizwanul Fattah, I.M.

    2015-01-01

    Highlights: • Short identification of selected biodiesel feedstock. • Review of physicochemical properties for blended biodiesel. • Mathematical model for predicting properties of various biodiesel blends. - Abstract: The growing demand for green world serves as one of the most significant challenges of modernization. Requirements like largest usage of energy for modern society as well as demand for friendly milieu create a deep concern in field of research. Biofuels are placed at the peak of the research arena for their underlying benefits as mentioned by multiple researches. Out of a number of vegetable oils, only a few are used commercially for biodiesel production. Due to various limitations of edible oil, non-edible oils are becoming a profitable choice. Till today, very little percentage of biodiesel is used successfully in engine. The research is still continuing for improving the biodiesel usage level. Recently, it is found that the blended biodiesel from more than one feedstock provides better performance in engine. This paper reviews the physicochemical properties of different biodiesel blends obtained from various feedstocks with a view to properly understand the fuel quality. Moreover, a short description of each feedstock is given along with graphical presentation of important properties for various blend percentages from B0 to B100. Finally, mathematical model is formed for predicting various properties of biodiesel blend with the help of different research data by using polynomial curve fitting method. The results obtained from a number of literature based on this work shows that the heating value of biodiesel is about 11% lower than diesel except coconut (14.5% lower) whereas kinematic viscosity is in the range of 4–5.4 mm 2 /s. Flash point of all biodiesels are more than 150 °C, except neem and coconut. Cold flow properties of calophyllum, palm, jatropha, moringa are inferior to others. This would help to determine important properties of

  15. Environmental impacts the of production and use of biodiesel.

    Science.gov (United States)

    Živković, Snežana; Veljković, Milan

    2018-01-01

    Biodiesel as renewable, environmental friendly, less toxic, and biodegradable is an attractive alternative to fossil fuels and is produced mainly from vegetable oils and animal fats. It is expected, globally, that the use of renewable biofuels, in general, will increase rapidly in the near future. The growing biodiesel production and usage have encouraged assessment of its impact on the environment. The present paper reviews various aspects of biodiesel production using commercial processing technology and biodiesel use through evaluation and analysis of the studies concerning environmental impacts of biodiesel. As a general conclusion, it can be said that biodiesel has the potential to offer a series of perceived benefits such as political, economical, and agricultural, as well as environmental (due to its biodegradability, less toxicity, renewability) and health (greenhouse gas-saving, less harmful exhaust emissions).

  16. Biodiesel production with special emphasis on lipase-catalyzed transesterification.

    Science.gov (United States)

    Bisen, Prakash S; Sanodiya, Bhagwan S; Thakur, Gulab S; Baghel, Rakesh K; Prasad, G B K S

    2010-08-01

    The production of biodiesel by transesterification employing acid or base catalyst has been industrially accepted for its high conversion and reaction rates. Downstream processing costs and environmental problems associated with biodiesel production and byproducts recovery have led to the search for alternative production methods. Recently, enzymatic transesterification involving lipases has attracted attention for biodiesel production as it produces high purity product and enables easy separation from the byproduct, glycerol. The use of immobilized lipases and immobilized whole cells may lower the overall cost, while presenting less downstream processing problems, to biodiesel production. The present review gives an overview on biodiesel production technology and analyzes the factors/methods of enzymatic approach reported in the literature and also suggests suitable method on the basis of evidence for industrial production of biodiesel.

  17. Influence of biodiesel on injection, fuel spray, and engine characteristics

    Directory of Open Access Journals (Sweden)

    Kegl Breda

    2008-01-01

    Full Text Available This paper discusses the influence of biodiesel on the injection, spray, and engine characteristics with the aim to reduce harmful emissions. The considered engine is a bus diesel engine with injection M system. The injection, fuel spray, and engine characteristics, obtained with biodiesel, are compared to those obtained with mineral diesel under peak torque and rated conditions. The considered fuel is neat biodiesel from rapeseed oil. Its density, viscosity, surface tension, and sound velocity are determined experimentally and compared to those of mineral diesel. The experimentally obtained results are used to analyze the most important injection, fuel spray, and engine characteristics. Furthermore, the influence of biodiesel usage on lubrication is presented briefly. The results indicate that, by using biodiesel, harmful emissions (NOx, CO, HC, smoke, and PM can be reduced to some extent by adjusting the injection pump timing properly while keeping other engine characteristics within acceptable limits. Furthermore, the results indicate better lubrication conditions when biodiesel is used.

  18. Effects of biodiesel on emissions of a bus diesel engine

    OpenAIRE

    Kegl, Breda

    2012-01-01

    This paper discusses the influence of biodiesel on the injection, spray, and engine characteristics with the aim to reduce harmful emissions. The considered engine is a bus diesel engine with injection M system. The injection, fuel spray, and engine characteristics, obtained with biodiesel, are compared to those obtained with mineral diesel (D2) under various operating regimes. The considered fuel is neat biodiesel from rapeseed oil. Its density, viscosity, surface tension, and sound velocity...

  19. Influence of biodiesel on injection, fuel spray, and engine characteristics

    OpenAIRE

    Kegl, Breda; Pehan, Stanislav

    2012-01-01

    This paper discusses the influence of biodiesel on the injection, spray, and engine characteristics with the aim to reduce harmful emissions. The considered engine is a bus diesel engine with injection M system. The injection, fuel spray, and engine characteristics, obtained with biodiesel, are compared to those obtained with mineral diesel under peak torque and rated conditions. The considered fuel is neat biodiesel from rapeseed oil. Its density, viscosity, surface tension, and sound veloci...

  20. Ultrasound Assisted Esterification of Rubber Seed Oil for Biodiesel Production

    OpenAIRE

    W Widayat; Berkah Fajar Tamtomo Kiono

    2012-01-01

    Production of biodiesel is currently shifting from the first to the second generation inwhich the raw materials are mostly from non-edible type oils and fats. Biodiesel production iscommonly conducted under batch operation using mechanical agitation to accelerate masstransfers. The main drawback of oil esterification is the high content of free fatty acids (FFA) whichmay reduce the yield of biodiesel and prolong the production time (2-5 hours). Ultrasonificationhas been used in many applicati...

  1. Combustion and Performance Characteristics of CI Engine Running with Biodiesel

    OpenAIRE

    Tesfa, Belachew; Mishra, Rakesh; Gu, Fengshou; Ball, Andrew

    2013-01-01

    Biodiesel is one of the alternative fuels which is renewable and environmentally friendly and can be used in diesel engines with little or no modifications. In the present study, experimental investigations were carried out on the effects of biodiesel types, biodiesel fraction and physical properties on the combustion and performance characteristics of a compression ignition (CI) engine. The experimental work was conducted on a four-cylinder, four -stroke, direct injection (DI) and turbocharg...

  2. Messiah College Biodiesel Fuel Generation Project Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Zummo, Michael M; Munson, J; Derr, A; Zemple, T; Bray, S; Studer, B; Miller, J; Beckler, J; Hahn, A; Martinez, P; Herndon, B; Lee, T; Newswanger, T; Wassall, M

    2012-03-30

    Many obvious and significant concerns arise when considering the concept of small-scale biodiesel production. Does the fuel produced meet the stringent requirements set by the commercial biodiesel industry? Is the process safe? How are small-scale producers collecting and transporting waste vegetable oil? How is waste from the biodiesel production process handled by small-scale producers? These concerns and many others were the focus of the research preformed in the Messiah College Biodiesel Fuel Generation project over the last three years. This project was a unique research program in which undergraduate engineering students at Messiah College set out to research the feasibility of small-biodiesel production for application on a campus of approximately 3000 students. This Department of Energy (DOE) funded research program developed out of almost a decade of small-scale biodiesel research and development work performed by students at Messiah College. Over the course of the last three years the research team focused on four key areas related to small-scale biodiesel production: Quality Testing and Assurance, Process and Processor Research, Process and Processor Development, and Community Education. The objectives for the Messiah College Biodiesel Fuel Generation Project included the following: 1. Preparing a laboratory facility for the development and optimization of processors and processes, ASTM quality assurance, and performance testing of biodiesel fuels. 2. Developing scalable processor and process designs suitable for ASTM certifiable small-scale biodiesel production, with the goals of cost reduction and increased quality. 3. Conduct research into biodiesel process improvement and cost optimization using various biodiesel feedstocks and production ingredients.

  3. A First Law Thermodynamic Analysis of Biodiesel Production from Soybean

    Science.gov (United States)

    Patzek, Tad W.

    2009-01-01

    A proper First Law energy balance of the soybean biodiesel cycle shows that the overall efficiency of biodiesel production is 0.18, i.e., only 1 in 5 parts of the solar energy sequestered as soya beans, plus the fossil energy inputs, becomes biodiesel. Soybean meal is produced with an overall energetic efficiency of 0.38, but it is not a fossil…

  4. Optimization of emergy sustainability index for biodiesel supply network design

    DEFF Research Database (Denmark)

    Ren, Jingzheng; Tan, Shiyu; Yang, Le

    2015-01-01

    sustainable design. In the proposed model, the emergy sustainability index of the whole biodiesel supply networks in a life cycle perspective is employed as the measure of the sustainability, and multiple feedstocks, multiple transport modes, multiple regions for biodiesel production and multiple distribution...... centers can be considered. After describing the process and mathematic framework of the model, an illustrative case was studied and demonstrated that the proposed methodology is feasible for finding the most sustainable design and planning of biodiesel supply chains....

  5. Pembuatan Biodiesel Dari Minyak Nyamplung Menggunakan Pemanasan Gelombang Mikro

    Directory of Open Access Journals (Sweden)

    Fatih Ridho Muhammad

    2014-09-01

    Full Text Available Energi fosil yang selama ini menjadi tumpuan penduduk seluruh dunia, jumlahnya semakin menipis dari waktu ke waktu. Peran minyak bumi dalam penyediaan energi nasional pun masih dominan. Sekitar 53% kebutuhan energi nasional dipenuhi dari minyak bumi. Oleh karena itu, pencarian energi alternatif pengganti minyak bumi harus dikembangkan, salah satunya biodiesel. Penggunaan microwave sebagai sumber energi pembuatan biodiesel dapat mempercepat waktu reaksi. Sehingga microwave dipandang lebih efisien. Biji nyamplung (Calophyllum inophyllum memiliki kandungan minyak sebesar 60,1% berat. Dengan kandungan minyak sebesar ini maka biji nyamplung memiliki potensi yang besar bila digunakan sebagai bahan baku pembuatan biodiesel. Nyamplung tersebar luas di pantai-pantai Indonesia. Tujuan penelitian ini adalah untuk mensintesa biodiesel dari minyak mentah nyamplung (Callophyluminophyllum dengan proses trans-esterifikasi dengan menggunakan microwave, mempelajari daya optimal dalam pembuatan biodiesel, mempelajari jumlah katalis yang dibutuhkan untuk mendapatkan biodiesel yang paling baik, mempelajari yield biodiesel yang dihasilkan serta mempelajari pengaruh penambahan ratio mol minyak-metanol terhadap kualitas biodiesel yang dihasilkan. Langkah awal pembuatan biodiesel nyamplung adalah proses degumming atau penghilangan impurities seperti getah, kemudian dilanjutkan dengan esterifikasi yang bertujuan untuk mengubah free fatty acid (FFA menjadi metil ester. Setelah esterifikasi, larutan dititrasi dengan NaOH dan indicator pp hingga konsentrasi FFA menjadi < 2%. Kemudian masuk proses trans-esterifikasi yang merubah trigliserida dalam minyak menjadi metil ester dan gliserol. Proses selanjutnya adalah pemisahan biodiesel dan gliserol dan terakhir proses pencucian. Variabel percobaan adalah kadar katalis CaO 2, 3, 4, 5, dan 6% berat minyak. Ratio mol minyak-metanol 1:9 dan 1:12. Variabel terakhir adalah daya microwave sebesar 100W, 264W dan 400W. Dari hasil

  6. Study about the particularities of biodiesel in Brazil; Estudo sobre as particularidades do biodiesel no Brasil

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Marcia Franca Ribeiro Fernandes dos [Instituto Brasileiro de Geografia e Estatistica (IBGE), Brasilia, DF (Brazil); Peixoto, Jose Antonio Assuncao; Souza, Cristina Gomes de [Centro Federal de Educacao Tecnologica Celso Suckow da Fonseca (CEFET/RJ), Rio de Janeiro, RJ (Brazil)

    2008-07-01

    The environmental concern associated with the impending shortage of oil, which is pressing to raise the price of the barrel, has forced governments and society to seek alternatives that will replace the use of fossil fuels. The biodiesel, in particular, has been set up as an alternative energy by it of fuel come from renewable sources, and less polluting the environment. In this context, the objective of this article is to present some features of the production of biodiesel in Brazil, identifying the characteristics of the main oil used, as well as regional motivations for the use of biodiesel in Brazil. The methodology adopted in this study was exploratory in nature based on a literature search and documentary from a survey of information available in literature. The main results, the article points out that: unlike alcohol, which is in sugar cane their ideal raw material, biodiesel is still in a stage of intensive research and development in order to identify the most appropriate its oil production - with emphasis on soybean and castor bean, and the motivations for regional use of biodiesel are different for the Brazilian regions. The study aims to contribute to the discussion on the subject, emphasizing that technological research should be directed taking into consideration the conditions and needs of Brazil. (author)

  7. PRELIMINARY DESIGN OF OSCILLATORY FLOW BIODIESEL REACTOR FOR CONTINUOUS BIODIESEL PRODUCTION FROM JATROPHA TRIGLYCERIDES

    Directory of Open Access Journals (Sweden)

    AZHARI T. I. MOHD. GHAZI

    2008-08-01

    Full Text Available The concept of a continuous process in producing biodiesel from jatropha oil by using an Oscillatory Flow Biodiesel Reactor (OFBR is discussed in this paper. It has been recognized that the batch stirred reactor is a primary mode used in the synthesis of biodiesel. However, pulsatile flow has been extensively researcehed and the fundamental principles have been successfully developed upon which its hydrodynamics are based. Oscillatory flow biodiesel reactor offers precise control of mixing by means of the baffle geometry and pulsation which facilitates to continuous operation, giving plug flow residence time distribution with high turbulence and enhanced mass and heat transfer. In conjunction with the concept of reactor design, parameters such as reactor dimensions, the hydrodynamic studies and physical properties of reactants must be considered prior to the design work initiated recently. The OFBR reactor design involves the use of simulation software, ASPEN PLUS and the reactor design fundamentals. Following this, the design parameters shall be applied in fabricating the OFBR for laboratory scale biodiesel production.

  8. Biodiesel Production from Vegetable Oil over Plasma Reactor: Optimization of Biodiesel Yield using Response Surface Methodology

    Directory of Open Access Journals (Sweden)

    Istadi Istadi

    2009-06-01

    Full Text Available Biodiesel production has received considerable attention in the recent past as a renewable fuel. The production of biodiesel by conventional transesterification process employs alkali or acid catalyst and has been industrially accepted for its high conversion and reaction rates. However for alkali catalyst, there may be risk of free acid or water contamination and soap formation is likely to take place which makes the separation process difficult. Although yield is high, the acids, being corrosive, may cause damage to the equipment and the reaction rate was also observed to be low. This research focuses on empirical modeling and optimization for the biodiesel production over plasma reactor. The plasma reactor technology is more promising than the conventional catalytic processes due to the reducing reaction time and easy in product separation. Copyright (c 2009 by BCREC. All Rights reserved.[Received: 10 August 2009, Revised: 5 September 2009, Accepted: 12 October 2009][How to Cite: I. Istadi, D.D. Anggoro, P. Marwoto, S. Suherman, B.T. Nugroho (2009. Biodiesel Production from Vegetable Oil over Plasma Reactor: Optimization of Biodiesel Yield using Response Surface Methodology. Bulletin of Chemical Reaction Engineering and Catalysis, 4(1: 23-31.  doi:10.9767/bcrec.4.1.7115.23-31][How to Link/ DOI: http://dx.doi.org/10.9767/bcrec.4.1.7115.23-31 || or local: http://ejournal.undip.ac.id/index.php/bcrec/article/view/7115

  9. Biodiesel Production from Vegetable Oil over Plasma Reactor: Optimization of Biodiesel Yield using Response Surface Methodology

    Directory of Open Access Journals (Sweden)

    Bambang Tri Nugroho

    2009-06-01

    Full Text Available Biodiesel production has received considerable attention in the recent past as a renewable fuel. The production of biodiesel by conventional transesterification process employs alkali or acid catalyst and has been industrially accepted for its high conversion and reaction rates. However for alkali catalyst, there may be risk of free acid or water contamination and soap formation is likely to take place which makes the separation process difficult. Although yield is high, the acids, being corrosive, may cause damage to the equipment and the reaction rate was also observed to be low. This research focuses on empirical modeling and optimization for the biodiesel production over plasma reactor. The plasma reactor technology is more promising than the conventional catalytic processes due to the reducing reaction time and easy in product separation. Copyright (c 2009 by BCREC. All Rights reserved.[Received: 10 August 2009, Revised: 5 September 2009, Accepted: 12 October 2009][How to Cite: I. Istadi, D.D. Anggoro, P. Marwoto, S. Suherman, B.T. Nugroho (2009. Biodiesel Production from Vegetable Oil over Plasma Reactor: Optimization of Biodiesel Yield using Response Surface Methodology. Bulletin of Chemical Reaction Engineering and Catalysis, 4(1: 23-31. doi:10.9767/bcrec.4.1.23.23-31][How to Link/ DOI: http://dx.doi.org/10.9767/bcrec.4.1.23.23-31

  10. Biodiesel fuel costs and environmental issues when powering railway locomotives

    Energy Technology Data Exchange (ETDEWEB)

    Mirza, Abdul; Ziemer, Norbert; Tatara, Robert; Moraga, Reinaldo; Mirman, Clifford; Vohra, Promod

    2010-09-15

    Issues for adopting biodiesel fuel, instead of petrodiesel, to power railroad locomotives are engine performance and emissions, fuel infrastructure, and fuel cost. These are evaluated for B2 through B100 blends. Biodiesel's solvent action on fuel systems is addressed. With biodiesel, hydrocarbon, carbon monoxide, and particulate emissions are unchanged or reduced. Nitrogen oxides are elevated but it is believed that engine alterations can minimize these emissions. A Transportation Model, using data from a major railway, has demonstrated that refueling depots can be fully supplied with biodiesel at a pricing premium of 1% to 26%, depending on blend and geographical location.

  11. Biodiesel production from sediments of a eutrophic reservoir

    International Nuclear Information System (INIS)

    Kuchkina, A.Yu.; Gladyshev, M.I.; Sushchik, N.N.; Kravchuk, E.S.; Kalachova, G.S.

    2011-01-01

    Sediments from eutrophic reservoir Bugach (Siberia, Russia) were tested for possibility to produce biodiesel. We supposed that the sediments could be a promising biodiesel producer. The major reason of high price of biodiesel fuel is cost of a raw material. The use of dredging sediments for biodiesel production reduces production costs, because the dredging sediments are by-products which originated during lake restoration actions, and are free of cost raw materials. Lipid content in sediments was 0.24% of dry weight. To assess the potential of from sediments as a substitute of diesel fuel, the properties of the biodiesel such as cetane number, iodine number and heat of combustion were calculated. All of this parameters complied with limits established by EN 14214 and EN 14213 related to biodiesel quality. -- Highlights: → Dredging sediments were considered as a new feedstock for biodiesel production. → Lipid and fatty acid content in the sediments were determined. → Main properties of the biodiesel were calculated basing on fatty acid composition. → The properties well complied with limits established in biodiesel standards.

  12. Prospects of Tectona Grandis as a Feedstock for Biodiesel

    International Nuclear Information System (INIS)

    Sarin, Amit; Singh, Meetu; Sharma, Neerja; Singh, N. P.

    2017-01-01

    The limited availability of fossil fuels has encouraged the need of replacement fuels of renewable nature. Among the renewable fuels, biodiesel produced from oil seeds and food wastes has been favored by the majority of researchers. In this study, Tectona Grandis seed oil has been investigated as a non-edible feedstock for biodiesel. The oil content of seed is 43% which makes it suitable for commercial production of biodiesel. The synthesis of biodiesel from T. Grandis oil was done with transesterification reaction giving high percentage yield of biodiesel which reached to 89%. The T. Grandis biodiesel was subjected to determine various physicochemical parameters by standard testing methods and found in agreement with the ASTM D-6751 and EN-14214 standards. The fatty-acid methyl ester composition for the biodiesel is composed of 42.71% oleic acid, 13.1% palmitic acid, and 31.51% linoleic acid. The biodiesel showed low oxidation stability which is attributed to high percentage of unsaturation. To address this issue, synthetic antioxidants were added to increase its resistance towards oxidation. By considering all the parameters, the present study reveals that T. Grandis seed oil is reliable for the production of biodiesel with encouraging probability in future.

  13. Investigation of friction and wear characteristics of palm biodiesel

    International Nuclear Information System (INIS)

    Fazal, M.A.; Haseeb, A.S.M.A.; Masjuki, H.H.

    2013-01-01

    Highlights: ► Both wear and friction decrease with the increase of biodiesel concentration. ► Wear and friction appear to decrease more at the range of 10–20% biodiesel in diesel blend. ► The wear of steel ball in biodiesel (B100) was 20% lower than that in diesel (B0). ► Lubricity in terms of wear and friction decreases with the increase of rotating speed. - Abstract: Use of biodiesel in automobile engine is creating tribology related new challenges. The present study aims to assess the friction and wear characteristics of palm biodiesel at different concentration level by using four-ball wear machine. The investigated fuels were biodiesel (B100), diesel (B0) and three different biodiesel blends such as B10 (10% biodiesel in diesel), B20, B50. Tests were conducted at 75 °C under a normal load of 40 kg for 1 h at four different speeds viz, 600, 900, 1200 and 1500 rpm. Worn surfaces of the balls were examined by SEM. Results showed that wear and friction decreased with the increase of biodiesel concentration. The wear of steel ball in B100 was appeared to be 20% lower than that in diesel (B0)

  14. Prospects of Tectona Grandis as a Feedstock for Biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Sarin, Amit, E-mail: amit.sarin@yahoo.com [Department of Physical Sciences, I.K. Gujral Punjab Technical University, Kapurthala (India); Singh, Meetu [Department of Applied Sciences, I.K. Gujral Punjab Technical University, Kapurthala (India); Sharma, Neerja [PG Department of Physics and Electronics, DAV College, Amritsar (India); Singh, N. P. [Department of Planning and External Development, I.K. Gujral Punjab Technical University, Kapurthala (India)

    2017-10-26

    The limited availability of fossil fuels has encouraged the need of replacement fuels of renewable nature. Among the renewable fuels, biodiesel produced from oil seeds and food wastes has been favored by the majority of researchers. In this study, Tectona Grandis seed oil has been investigated as a non-edible feedstock for biodiesel. The oil content of seed is 43% which makes it suitable for commercial production of biodiesel. The synthesis of biodiesel from T. Grandis oil was done with transesterification reaction giving high percentage yield of biodiesel which reached to 89%. The T. Grandis biodiesel was subjected to determine various physicochemical parameters by standard testing methods and found in agreement with the ASTM D-6751 and EN-14214 standards. The fatty-acid methyl ester composition for the biodiesel is composed of 42.71% oleic acid, 13.1% palmitic acid, and 31.51% linoleic acid. The biodiesel showed low oxidation stability which is attributed to high percentage of unsaturation. To address this issue, synthetic antioxidants were added to increase its resistance towards oxidation. By considering all the parameters, the present study reveals that T. Grandis seed oil is reliable for the production of biodiesel with encouraging probability in future.

  15. Environmental sustainability assessment of palm biodiesel production in Thailand

    International Nuclear Information System (INIS)

    Silalertruksa, Thapat; Gheewala, Shabbir H.

    2012-01-01

    The study assesses the environmental sustainability of palm biodiesel production systems in Thailand by focusing on their energy efficiency and environmental impact potentials. The Net Energy Balance (NEB) and Renewability indicate energy gain for palm biodiesel and its co-products as compared to fossil energy inputs. In addition, life cycle assessment also reveals lower values of environmental impact potentials of biodiesel as compared to conventional diesel. For example, palm biodiesel can provide greenhouse gas (GHG) reduction of around 46–73% as compared to diesel. Nitrogen-fertilizer production and application in the plantation and the air emissions from the ponds treating palm oil mill effluent (POME) are found to be the major environmental aspects. However, the energy and environmental performances depend on various factors such as the management efficiency of empty fruit bunches (EFB) and POME and the possible land-use change in the future. Recommendations are made for improving environmental performance of palm biodiesel and for securing the long-term availability of crude palm oil supply with a view towards sustainable palm biodiesel production. -- Highlights: ► Environmental sustainability of palm biodiesel production in Thailand is assessed. ► Palm biodiesel can provide GHG reduction of around 46–73% as compared to diesel. ► Net energy ratio and renewability of palm biodiesel both range between 2 and 4. ► Efficient use of by-products in the value chain enhances environmental benefits.

  16. Assessment of the biodiesel distribution infrastructure in Canada

    International Nuclear Information System (INIS)

    Lagace, C.

    2007-08-01

    Canada's biodiesel industry is in its infancy, and must work to achieve the demand needed to ensure its development. This assessment of Canada's biodiesel distribution infrastructure was conducted to recommend the most efficient infrastructure pathway for effective biodiesel distribution. The study focused on the establishment of a link between biodiesel supplies and end-users. The current Canadian biodiesel industry was discussed, and future market potentials were outlined. The Canadian distillate product distribution infrastructure was discussed. Technical considerations and compliance issues were reviewed. The following 2 scenarios were used to estimate adaptations and costs for the Canadian market: (1) the use of primary terminals to ensure quality control of biodiesel, and (2) storage in secondary terminals where biodiesel blends are prepared before being transported to retail outlets. The study showed that relevant laboratory training programs are needed as well as proficiency testing programs in order to ensure adequate quality control of biodiesel. Standards for biodiesel distribution are needed, as well as specifications for the heating oil market. It was concluded that this document may prove useful in developing government policy objectives and identifying further research needs. 21 refs., 12 tabs., 13 figs

  17. Purification of biodiesel by choline chloride based deep eutectic solvent

    Science.gov (United States)

    Niawanti, Helda; Zullaikah, Siti; Rachimoellah, M.

    2017-05-01

    Purification is a crucial step in biodiesel production to meet the biodiesel standard. This study purified biodiesel using choline chloride based deep eutectic solvent (DES). DES was used to reduce unreacted oil and unsaponifiable matter in rice bran oil based biodiesel. The objective of this work was to study the effect of extraction time using DES on the content and yield of fatty acid methyl ester (FAME). Rice bran used in this work contains 16.49 % of oil with initial free fatty acids (FFA) of 44.75 %. Acid catalyzed methanolysis was employed to convert rice bran oil (RBO) into biodiesel under following operation conditions: T = 60 °C, t = 8 h, molar ratio of oil to methanol = 1/10, H2SO4 = 1% w/w of oil. Rice bran oil based biodiesel obtained contain 89.05 % of FAME with very low FFA content (0.05 %). DES was made from a mixture of choline chloride and ethylene glycol with molar ratio of 1/2. Molar ratio of crude biodiesel to DES were 1/2 and 1/4. Extraction time was varied from 15 minutes to 240 minutes at 30 °C. The highest FAME content was obtained after purification for 240 min. at molar ratio crude biodiesel to DES 1/4 was 96.60 %. This work shows that DES has potential to purify biodiesel from non-edible raw material, such as RBO.

  18. Impact of ternary blends of biodiesel on diesel engine performance

    Directory of Open Access Journals (Sweden)

    Prem Kumar

    2016-06-01

    Full Text Available The Pongamia and waste cooking oils are the main non edible oils for biodiesel production in India. The aim of the present work is to evaluate the fuel properties and investigate the impact on engine performance using Pongamia and waste cooking biodiesel and their ternary blend with diesel. The investigation of the fuel properties shows that Pongamia biodiesel and waste cooking biodiesel have poor cold flow property. This will lead to starting problem in the engine operation. To overcome this problem the ternary blends of diesel, waste cooking biodiesel and Pongamia biodiesel are prepared. The cloud and pour point for ternary blend, (WCB20:PB20:D60 were found to be 7 °C and 6.5 °C which are comparable to cloud and pour point of diesel 6 °C and 5 °C, respectively. The result of the test showed that brake specific fuel consumption for Pongamia biodiesel and waste cooking biodiesel is higher than ternary blend, (WCB20:PB20:D60 due to their lower energy content. The brake thermal efficiency of ternary blend and diesel is comparable while the Pongamia and waste cooking biodiesel have low efficiency. The result of investigation showed that ternary blend can be developed as alternate fuel.

  19. Analysis of the Industrial Biodiesel Production Process

    International Nuclear Information System (INIS)

    Di Nicola, G.; Moglie, M.; Santori, G.

    2009-01-01

    The reaction of transesterification is the chemical transformation through which you get biodiesel from vegetable oils. The purpose of this work is to plan carefully all the stages of various biodiesel production processes on the basis of recent results obtained in the experimental research. These results allow defining the proper thermodynamic models to be used, the right interpretation of the phenomena and identifying the parameters which affect the process. The modelling was done with ASPENPLUS (R) defining three possible processes used in industrial purpose. A subsequent sensitivity analysis was done for each process allowing the identification of the optimal configurations. By comparing these solutions it is possible to choose the most efficient one to reduce the costs of the final product. [it

  20. Enzymatic biodiesel production from free fatty acids

    OpenAIRE

    Afonso, Marise da Costa Pereira

    2009-01-01

    O ácido oleico é um co-produto da refinação de óleos alimentares e é removido num passo antecedente à catalise alcalina na produção industrial de biodiesel. Este ácido gordo livre é uma fonte alternativa de biodiesel. Neste trabalho estudou-se a esterificação enzimática do acido oleico com metanol ou etanol. Definiu-se um planeamento experimental 22 para estudar a influência das variáveis razão molar álcool/ácido oleico(R) e concentração de enzima(E), as variáveis dependentes, na percentag...

  1. Optimization of biodiesel production from castor oil.

    Science.gov (United States)

    da Silva, Nivea de Lima; Maciel, Maria Regina Wolf; Batistella, César Benedito; Maciel Filho, Rubens

    2006-01-01

    The transesterification of castor oil with ethanol in the presence of sodium ethoxide as catalyst is an exceptional option for the Brazilian biodiesel production, because the castor nut is quite available in the country. Chemically, its oil contains about 90% of ricinoleic acid that gives to the oil some beneficial characteristics such as its alcohol solubility at 30 degrees C. The transesterification variables studied in this work were reaction temperature, catalyst concentration and alcohol oil molar ratio. Through a star configuration experimental design with central points, this study shows that it is possible to achieve the same conversion of esters carrying out the transesterification reaction with a smaller alcohol quantity, and a new methodology was developed to obtain high purity biodiesel.

  2. Evaluating the economics of biodiesel in Africa

    International Nuclear Information System (INIS)

    Mulugetta, Yacob

    2009-01-01

    Road transport in Sub-Saharan Africa is expected to rise in the coming years. Paradoxically, this expansion is occurring at a time when oil prices have reached new heights. Unstable oil prices do indeed increase the vulnerability of importers. However, it also presents them with a unique opportunity to explore promising technical options to help reduce their over-reliance on imported petroleum fuels. This paper takes a closer look at the potential for biodiesel, with an emphasis on fuels produced from oil palm, castor oil and jatropha in Ghana, Kenya and Tanzania, respectively. The paper provides an economic appraisal of biodiesels from these feedstocks, and sets the context for further discussions on biofuels in Africa. (author)

  3. Biodiesel: uma energia alternativa e verde

    Directory of Open Access Journals (Sweden)

    Milena Carvalho Teixeira

    2010-12-01

    Full Text Available O presente texto busca expor a importância do uso de energias alternativas. O biodiesel é apontado como uma das soluções para o esgotamento do petróleo e seus derivados e para o problema do aquecimento global, e o Brasil, por apresentar biodiversidade e forte economia agrícola, permitiu que o Governo Federal criasse o Programa Nacional de Produção e Uso de Biodiesel (PNPB com chances de sucesso. O programa explora várias fontes energéticas, de culturas temporárias e perenes ao uso do óleo residual, além de trazer benefícios ao desenvolvimento do país, gerando emprego e renda, e, principalmente, redução nas emissões de gás carbônico.

  4. Fast gas chromatographic separation of biodiesel.

    Science.gov (United States)

    Pauls, R E

    2011-05-01

    A high-speed gas chromatographic method has been developed to determine the FAME distribution of B100 biodiesel. The capillary column used in this work has dimensions of 20 m × 0.100 mm and is coated with a polyethylene glycol film. Analysis times are typically on the order of 4-5 min depending upon the composition of the B100. The application of this method to a variety of vegetable and animal derived B100 is demonstrated. Quantitative results obtained with this method were in close agreement with those obtained by a more conventional approach on a 100 m column. The method, coupled with solid-phase extraction, was also found suitable to determine the B100 content of biodiesel-diesel blends.

  5. Landfill gas, canola, and biodiesel. Working towards a sustainable system [Snohomish County Biodiesel Project

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Terrill; Carveth, Deanna

    2010-02-01

    Snohomish County in western Washington State began converting its vehicle fleet to use a blend of biodiesel and petroleum diesel in 2005. As prices for biodiesel rose due to increased demand for this cleaner-burning fuel, Snohomish County looked to its farmers to grow this fuel locally. Suitable seed crops that can be crushed to extract oil for use as biodiesel feedstock include canola, mustard, and camelina. The residue, or mash, has high value as an animal feed. County farmers began with 52 acres of canola and mustard crops in 2006, increasing to 250 acres and 356 tons in 2008. In 2009, this number decreased to about 150 acres and 300 tons due to increased price for mustard seed.

  6. Biodiesel Reactor Design with Glycerol Separation to Increase Biodiesel Production Yield

    Directory of Open Access Journals (Sweden)

    Budy Rahmat

    2013-09-01

    Full Text Available The study consisted of reactor design used for transesterification process, effect of glycerol separation ontransesterification reaction, determination of biodiesel quality, and mass balance analysis. The reactor was designed byintegrating circulated pump/stirrer, static mixer, and sprayer that intensify the reaction in the outer tank reactor. The objective was to reduce the use of methanol in excess and to shorten the processing time. The results showed that thereactor that applied the glycerol separation was able to compensate for the decreased use of the reactant methanol from 6:1 to 5:1 molar ratio, and changed the mass balance in the product, including: (i the increase of biodiesel productionfrom 42.37% to 49.34%, and (ii the reduction of methanol in excess from 42.37% to 32.89%. The results suggested that the efficiency of biodiesel production could be increased with the glycerol separation engineering.

  7. Castor oil biodiesel: an economic evaluation; Biodiesel de mamona: uma avaliacao economica

    Energy Technology Data Exchange (ETDEWEB)

    Pires, Monica de Moura; Alves, Jaenes Miranda; Almeida Neto, Jose Adolfo de; Almeida, Cezar Menezes; Sousa, Geovania Silva de; Cruz, Rosenira Serpa da; Monteiro, Renata; Lopes, Beatriz Sampaio; Robra, Sabine [Universidade Estadual de Santa Cruz, Ilheus, BA (Brazil). Grupo Bioenergia e Meio Ambiente]. E-mails: mpires@uesc.br; jaenes@uesc.br; jalmeida@uesc.br; roserpa@uesc.br

    2004-07-01

    The production cost of castor oil biodiesel by methyl way and its economic viability, using as reference the production cost data of castor oil and the implantation of the pilot plant at UESC - state university of Santa Cruz, Bahia State, Brazil was determined. From this information, it was seen that the estimated price of castor oil biodiesel is close to the diesel price in the Itabuna market, Bahia state, Brazil. The indicators show economic viability of the mini-power plant installation. Such information are preliminary estimative for the market and can be modified as function of changes in the main factors used to have the production costs, as well as the sectorial policies that drives the activity as much in levels of raw material production as in biodiesel.

  8. Strategic planning of biodiesel supply chain

    OpenAIRE

    García Cáceres, Rafael Guillermo; Universidad Pedagógica y Tecnológica de Colombia - UPTC

    2017-01-01

    Introduction:A stochastic biobjective MIP model for designing the network of biodiesel supply chains is presented. Ultimately intending to support the strategic decisions of stakeholders. The constraints included are: economies of scale, location of facilities, production capacity, raw material supply, product demand, bill of materials and mass balance.Objectives:The model aims to minimize, both, the total cost and environmental impact of five chain echelonsMetodology:The solution procedure r...

  9. Biodiesel production by enzyme-catalyzed transesterification

    OpenAIRE

    Stamenković Olivera S.; Lazić Miodrag L.; Veljković Vlada B.; Skala Dejan U.

    2005-01-01

    The principles and kinetics of biodiesel production from vegetable oils using lipase-catalyzed transesterification are reviewed. The most important operating factors affecting the reaction and the yield of alkyl esters, such as: the type and form of lipase, the type of alcohol, the presence of organic solvents, the content of water in the oil, temperature and the presence of glycerol are discussed. In order to estimate the prospects of lipase-catalyzed transesterification for industrial appli...

  10. Determinants of stakeholders? attitudes towards biodiesel

    OpenAIRE

    Amin, Latifah; Hashim, Hasrizul; Mahadi, Zurina; Ibrahim, Maznah; Ismail, Khaidzir

    2017-01-01

    Background Concern about the inevitable depletion of global energy resources is rising and many countries are shifting their focus to renewable energy. Biodiesel is one promising energy source that has garnered much public attention in recent years. Many believe that this alternative source of energy will be able to sustain the need for increased energy security while at the same time being friendly to the environment. Public opinion, as well as proactive measures by key players in industry, ...

  11. Biodiesel Production from Azolla filiculoides (Water Fern ...

    African Journals Online (AJOL)

    Results: The presence of myristic acid (C14:0), palmitic acid (C16:0), palmitoleic acid (C16:1), myristic acid (C14:0), stearic acid (C18:3), oleic acid (C18:1) and linoleic acid 9C18:2), eicosenoic acid (C20:1), eicosapentaenoic acid (C20:5), erucic acid (C22:1) and docosahexaenoic acid (C22:6) in the macroalgae biodiesel ...

  12. An experimental investigation of biodiesel steam reforming

    OpenAIRE

    Martin, Stefan; Kraaij, Gerard; Ascher, Torsten; Wails, David; Wörner, Antje

    2015-01-01

    Recently, liquid biofuels have attracted increasing attention as renewable feedstock for hydrogen production in the transport sector. Since the lack of hydrogen infrastructure and distribution poses an obstacle for the introduction of fuel cell vehicles to the market, it is reasonable to consider using liquid biofuels for on-board or on-site hydrogen generation. Biodiesel offers the advantage of being an environmentally friendly resource while also having high gravimetric and volumetric energ...

  13. Dezentrale Wasserstofferzeugung aus Diesel und Biodiesel

    OpenAIRE

    Martin, Stefan; Ascher, Torsten; Kraaij, Gerard; Dietrich, Ralph-Uwe; Wörner, Antje

    2015-01-01

    Der Energieträger Wasserstoff wird im Verkehrssektor in den kommenden Jahren zunehmend an Bedeutung gewinnen. Eine mögliche Alternative zur zentralen H2-Erzeugung aus Erdgas ist die dezentrale Bereitstellung von Wasserstoff durch Reformierung von Flüssigbrennstoffen. Im Rahmen des EU-Projektes NEMESIS2+ (www.nemesis-project.eu) wird ein Wasserstoffgenerator (50 Nm3/h) auf Basis von Diesel und Biodiesel entwickelt. Am DLR Stuttgart werden im Rahmen des Projektes grundlegende experimentelle Unt...

  14. Fremtidens Biodiesel: Kom fedtaffald i tanken!

    DEFF Research Database (Denmark)

    Madsen, Anders Theilgaard; Taarning, Esben; Christensen, Claus Hviid

    2009-01-01

    Mange tror måske, at det er svært for menigmand at lave biobrændstof. Det er faktisk forkert, fordi biodiesel nemt kan laves af kemikalier, der er ret almindelige i laboratorier og hos købmanden og materialisten. Det kræver blot en såkaldt om-estring af planteolie eller fedt med methanol, samt...

  15. del biodiesel de aceite de palma

    Directory of Open Access Journals (Sweden)

    Pedro Nel Benjumea

    2007-01-01

    Full Text Available El deficiente desempeño del biodiesel de aceite de palma (BAP a bajas temperaturas constituye su mayor deficiencia de calidad y el limitante para propiciar el uso de este combustible alternativo para motores diesel puro o mezclado en altas proporciones con el combustible diesel convencional derivado del petróleo (ACPM. En este trabajo se evalúan varias alternativas para mejorar las propiedades de flujo a baja temperatura (PFBT del BAP. Mediante la producción del biodiesel utilizando alcoholes ramificados como el isopropanol, isobutanol, 2-butanol e isopentanol se obtienen alquilésteres del aceite de palma con puntos de nube y fl uidez más bajos que los correspondientes a los metilésteres. La sustitución del grupo metil por el isopentil permite obtener reducciones en los puntos de nube y fluidez de 8 y 21 ºC, respectivamente. Los isopropilésteres del aceite de palma poseen un punto de nube 10 ºC menor que el de los metilésteres. El punto de nube de las mezclas BAP-ACPM se incrementa en forma lineal con el contenido del biodiesel en la mezcla. Para las mezclas probadas (B5, B20 y B30 solo se presentan problemas de filtrabilidad del combustible a temperaturas por debajo de -4 ºC. En este trabajo se evaluó la efectividad de dos aditivos comerciales mejoradores de flujo para reducir el punto de obstrucción de filtros en frío (POFF del biodiesel puro y las mezclas probadas. Los resultados obtenidos mostraron que con dichos aditivos solamente es posible obtener reducciones en el POFF de la mezcla B5 cuando se usa la menor de las tres concentraciones de aditivo probadas.

  16. Light vehicle regulated and unregulated emissions from different biodiesels

    International Nuclear Information System (INIS)

    Karavalakis, George; Stournas, Stamoulis; Bakeas, Evangelos

    2009-01-01

    In this study, the regulated and unregulated emissions profile and fuel consumption of an automotive diesel and biodiesel blends, prepared from two different biodiesels, were investigated. The biodiesels were a rapeseed methyl ester (RME) and a palm-based methyl ester (PME). The tests were performed on a chassis dynamometer with constant volume sampling (CVS) over the New European Driving Cycle (NEDC) and the non-legislated Athens Driving Cycle (ADC), using a Euro 2 compliant passenger vehicle. The objectives were to evaluate the impact of biodiesel chemical structure on the emissions, as well as the influence of the applied driving cycle on the formation of exhaust emissions and fuel consumption. The results showed that NOx emissions were influenced by certain biodiesel properties, such as those of cetane number and iodine number. NOx emissions followed a decreasing trend over both cycles, where the most beneficial reduction was obtained with the application of the more saturated biodiesel. PM emissions were decreased with the palm-based biodiesel blends over both cycles, with the exception of the 20% blend which was higher compared to diesel fuel. PME blends led to increases in PM emissions over the ADC. The majority of the biodiesel blends showed a tendency for lower CO and HC emissions. The differences in CO2 emissions were not statistically significant. Fuel consumption presented an increase with both biodiesels. Total PAH and nitro-PAH emission levels were decreased with the use of biodiesel independently of the source material. Lower molecular weight PAHs were predominant in both gaseous and particulate phases. Both biodiesels had a negative impact on certain carbonyl emissions. Formaldehyde and acetaldehyde were the dominant aldehydes emitted from both fuels.

  17. Light vehicle regulated and unregulated emissions from different biodiesels.

    Science.gov (United States)

    Karavalakis, George; Stournas, Stamoulis; Bakeas, Evangelos

    2009-05-01

    In this study, the regulated and unregulated emissions profile and fuel consumption of an automotive diesel and biodiesel blends, prepared from two different biodiesels, were investigated. The biodiesels were a rapeseed methyl ester (RME) and a palm-based methyl ester (PME). The tests were performed on a chassis dynamometer with constant volume sampling (CVS) over the New European Driving Cycle (NEDC) and the non-legislated Athens Driving Cycle (ADC), using a Euro 2 compliant passenger vehicle. The objectives were to evaluate the impact of biodiesel chemical structure on the emissions, as well as the influence of the applied driving cycle on the formation of exhaust emissions and fuel consumption. The results showed that NO(x) emissions were influenced by certain biodiesel properties, such as those of cetane number and iodine number. NO(x) emissions followed a decreasing trend over both cycles, where the most beneficial reduction was obtained with the application of the more saturated biodiesel. PM emissions were decreased with the palm-based biodiesel blends over both cycles, with the exception of the 20% blend which was higher compared to diesel fuel. PME blends led to increases in PM emissions over the ADC. The majority of the biodiesel blends showed a tendency for lower CO and HC emissions. The differences in CO(2) emissions were not statistically significant. Fuel consumption presented an increase with both biodiesels. Total PAH and nitro-PAH emission levels were decreased with the use of biodiesel independently of the source material. Lower molecular weight PAHs were predominant in both gaseous and particulate phases. Both biodiesels had a negative impact on certain carbonyl emissions. Formaldehyde and acetaldehyde were the dominant aldehydes emitted from both fuels.

  18. Use of waste materials for biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    Vitiello, R.; Tesser, R.; Di Serio, M.; Santacesaria, E. [Napoli Univ. (Italy). Dipt. di Scienze Chimiche; Buonerba, A.; Grassi, A. [Salerno Univ. (Italy). Dipt. di Chimica e Biologia

    2012-07-01

    Waste raw materials obtained by several sources of both food and agro industries could be considered for biofuel production. In the last years, this topic has growing in interest. At this purpose, our research, has been focused on the development of new technologies to obtain biodiesel from the mentioned wastes feedstock. In particular from oleins, that are mixtures of free fatty acids (FFAs) and triglycerides. Therefore, we are studying the way to produce biodiesel in two steps: an esterification reaction of FFAs with glycerol and a transesterification with methanol of the whole mixture. The esterification of FFAs with glycerol has the advantage of using a relatively high temperature favouring the stripping of water formed during the esterification. In this way esterification equilibrium is shifted to the right. Then, the mixture of mono-, di- and triglycerides, obtained by esterification with glycerol, can be submitted to transesterification with methanol, in the usual way, to produce biodiesel Catalysts promoting esterification, normally, are mineral acids or heterogeneous Bronsted acid catalysts. At this purpose, the classical sulphonated polystyrene acid resins cannot be used at temperature greater than 120 C. Therefore, a new class of sulfonated polymers, with enhanced temperature resistance, has been developed by selective and quantitative sulfonation of olefinic butadiene units in multiblock copolymers syndiotactic polystyrene-co-1,4-cis-polybutadiene. This catalytic system has been successfully tested in the above mentioned esterification reaction and compared to classic commercial strong acid catalysts like Amberlyst {sup registered}, Nafion {sup registered} and sulfuric acid. (orig.)

  19. Producing affordable high-quality biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Draak, H. D.

    2004-12-31

    A novel process to produce biodiesel fuel, used to power an automobile and heat a single-family home, including a domestic hot water heater, is discussed. Although currently used on a very small scale, the process is said to be capable of producing biodiesel on a commercial scale and marketed at the same wholesale price as petro-diesel, with enough price flexibility to adjust up or down to keep pace with fluctuations in oil prices. The basic materials used are canola oil and used fryer oil from restaurants. The crucial points are to pre-treat the used fryer oil to remove impurities, and to wash the newly-produced biodiesel afterwards. Using these materials, production cost is 19 cents per liter (before overhead). Public apathy and the lack of an infrastructure for distribution are major obstacles to commercial-scale production, but the inventor of the process is confident that with a dwindling oil supply and ever-rising oil prices, the opportunities for change to alternative sources of energy are constantly improving. photos.

  20. Production of biodiesel using the microwave technique

    Directory of Open Access Journals (Sweden)

    Shakinaz A. El Sherbiny

    2010-10-01

    Full Text Available Biodiesel production is worthy of continued study and optimization of production procedures because of its environmentally beneficial attributes and its renewable nature. Non-edible vegetable oils such as Jatropha oil, produced by seed-bearing shrubs, can provide an alternative and do not have competing food uses. However, these oils are characterized by their high free fatty acid contents. Using the conventional transesterification technique for the production of biodiesel is well established. In this study an alternative energy stimulant, “microwave irradiation”, was used for the production of the alternative energy source, biodiesel. The optimum parametric conditions obtained from the conventional technique were applied using microwave irradiation in order to compare the systems. The study showed that the application of radio frequency microwave energy offers a fast, easy route to this valuable biofuel with the advantages of enhancing the reaction rate (2 min instead of 150 min and of improving the separation process. The methodology allows for the use of high free fatty acid content feedstock, including Jatropha oil. However, this emerging technology needs to be further investigated for possible scale-up for industrial application.

  1. Technoeconomic study of supercritical biodiesel production plant

    International Nuclear Information System (INIS)

    Marchetti, J.M.; Errazu, A.F.

    2008-01-01

    Over the last years, biodiesel has gained more market due to its benefits and because it appears as the natural substitute for diesel. However, the highest cost of this process is associated with the raw material employed, making it a less competitive and more expensive fuel. Therefore, research is being done in order to use low price raw material, such as acid oils, frying oils or soapstocks. In this work, a biodiesel production plant was developed using supercritical methanol and acid oils as raw materials. This technology was compared with some other alternatives previously described with the aim of making a comparative study, not only on the technical aspects but also on the economic results. A process simulator was employed to produce the conceptual design and simulate each technology. Using these models, it was possible to analyze different scenarios and to evaluate productivity, raw material consumption, economic competitiveness and environmental impacts of each process. Although the supercritical alternative appears as a good technical possibility to produce biodiesel, today, it is not an economic alternative due to its high operating costs

  2. Biodiesel production using a membrane reactor.

    Science.gov (United States)

    Dubé, M A; Tremblay, A Y; Liu, J

    2007-02-01

    The immiscibility of canola oil in methanol provides a mass-transfer challenge in the early stages of the transesterification of canola oil in the production of fatty acid methyl esters (FAME or biodiesel). To overcome or rather, exploit this situation, a two-phase membrane reactor was developed to produce FAME from canola oil and methanol. The transesterification of canola oil was performed via both acid- or base-catalysis. Runs were performed in the membrane reactor in semi-batch mode at 60, 65 and 70 degrees C and at different catalyst concentrations and feed flow rates. Increases in temperature, catalyst concentration and feedstock (methanol/oil) flow rate significantly increased the conversion of oil to biodiesel. The novel reactor enabled the separation of reaction products (FAME/glycerol in methanol) from the original canola oil feed. The two-phase membrane reactor was particularly useful in removing unreacted canola oil from the FAME product yielding high purity biodiesel and shifting the reaction equilibrium to the product side.

  3. Cleaning up a biodiesel plant

    International Nuclear Information System (INIS)

    Wallace, Paula

    2012-01-01

    Full text: The project at Biodiesel Producers Limited in Victoria involved remediation of a wastewater treatment process containing a large covered anaerobic lagoon, an aerobic sequencing batch reactor (SBR) and a series of downstream open ponds. The pond downstream of the SBR was heavily loaded with a thick hard grease cap. The CAL was believed to have a metre-plus grease cap and the SBR had developed a thick foam cap that prevented aeration and mixing. Environmental Biotech was called in to assist with bioremediation using its Grease Eradication System bacteria cultures, with the aim of reducing the fats, oil and grease in the CAL discharge to less than 150 milligrams per litre, eliminating the stable fat foam in the SBR to allow the denitrification sequencing program to be reinstated and to clean up the hard fat layer from the surfaces of the comany's open ponds. The inflow to the CAL was designed for a flow of 210kL per day with a loading of 6900mg/L biochemical oxygen demand and FOG of 425mg/L. The actual load, as measured by Environmental Biotech, was 100kL with 20,000mg/L BOD and 1800mg/L (180kg) FOG. The CAL had been in use for more than two years, generating methane but assumed to be working well in the breakdown of chemical oxygen demand and FOG. In December 2009 the quality of the effluent began to decrease, overloading the SBR with FOG. It caused the formation of dense foam on aeration and mixing. The foam would not break down despite a variety of methods being employed and would overflow from the walls of the SBR. “Due to the foaming issue the SBR became a large holding tank for the fat and because of the reduced mixing, the solids were settling on the bottom of the tank,” Environmental Biotech project manager and franshisee Craig Barr said. “We were brought in to start work inApril 2010 and initially we slug dosed the CAL with 400 litres of GES bacteria in addition to a constant metered dosing rate of 400 litres per fortnight with the

  4. Lipids from yeasts and fungi: Tomorrow's source of Biodiesel?

    NARCIS (Netherlands)

    Meeuwse, P.; Sanders, J.P.M.; Tramper, J.; Rinzema, A.

    2013-01-01

    In the search for new transport fuels from renewable resources, biodiesel from microbial lipids comes into view. We have evaluated the lipid yield and energy use of a process for production of biodiesel from agricultural waste using lipid-accumulating yeast and fungi. We included different

  5. Direct transesterification of spent coffee grounds for biodiesel production

    Science.gov (United States)

    Studies of spent coffee grounds (SCGs) as a potential biodiesel feedstock in recent years mostly started from solvent extraction to obtain coffee oil, and then converted it into coffee biodiesel in two steps, acid esterification followed by alkaline transesterification. This paper presents a direct ...

  6. Optimization of biodiesel production from castor oil by response ...

    African Journals Online (AJOL)

    This work investigated the possibility of using response surface methodology based on a four factor five level central composite design to optimize biodiesel production from castor oil. The reaction variables were oil: ethanol ratio, lipozyme concentration, time and temperature. The properties of the biodiesel produced were ...

  7. An investigation of biodiesel production from wastes of seafood restaurants.

    Science.gov (United States)

    El-Gendy, Nour Sh; Hamdy, A; Abu Amr, Salem S

    2014-01-01

    This work illustrates a comparative study on the applicability of the basic heterogeneous calcium oxide catalyst prepared from waste mollusks and crabs shells (MS and CS, resp.) in the transesterification of waste cooking oil collected from seafood restaurants with methanol for production of biodiesel. Response surface methodology RSM based on D-optimal deign of experiments was employed to study the significance and interactive effect of methanol to oil M : O molar ratio, catalyst concentration, reaction time, and mixing rate on biodiesel yield. Second-order quadratic model equations were obtained describing the interrelationships between dependent and independent variables to maximize the response variable (biodiesel yield) and the validity of the predicted models were confirmed. The activity of the produced green catalysts was better than that of chemical CaO and immobilized enzyme Novozym 435. Fuel properties of the produced biodiesel were measured and compared with those of Egyptian petro-diesel and international biodiesel standards. The biodiesel produced using MS-CaO recorded higher quality than that produced using CS-CaO. The overall biodiesel characteristics were acceptable, encouraging application of CaO prepared from waste MS and CS for production of biodiesel as an efficient, environmentally friendly, sustainable, and low cost heterogeneous catalyst.

  8. Production of Biodiesel from Parinari polyandra B. Seed Oil using ...

    African Journals Online (AJOL)

    Akorede

    of converting vegetable oil to alkyl of fatty acids esters. (biodiesel) by reacting it with alcohol. Specifically, oil triglyceride reacts with methanol to produce fatty acid methyl esters (FAME) and glycerol in the presence of a catalyst. The oil or fat used for biodiesel production is determined by the abundance of seed oils that are ...

  9. An Investigation of Biodiesel Production from Wastes of Seafood Restaurants

    Directory of Open Access Journals (Sweden)

    Nour Sh. El-Gendy

    2014-01-01

    Full Text Available This work illustrates a comparative study on the applicability of the basic heterogeneous calcium oxide catalyst prepared from waste mollusks and crabs shells (MS and CS, resp. in the transesterification of waste cooking oil collected from seafood restaurants with methanol for production of biodiesel. Response surface methodology RSM based on D-optimal deign of experiments was employed to study the significance and interactive effect of methanol to oil M : O molar ratio, catalyst concentration, reaction time, and mixing rate on biodiesel yield. Second-order quadratic model equations were obtained describing the interrelationships between dependent and independent variables to maximize the response variable (biodiesel yield and the validity of the predicted models were confirmed. The activity of the produced green catalysts was better than that of chemical CaO and immobilized enzyme Novozym 435. Fuel properties of the produced biodiesel were measured and compared with those of Egyptian petro-diesel and international biodiesel standards. The biodiesel produced using MS-CaO recorded higher quality than that produced using CS-CaO. The overall biodiesel characteristics were acceptable, encouraging application of CaO prepared from waste MS and CS for production of biodiesel as an efficient, environmentally friendly, sustainable, and low cost heterogeneous catalyst.

  10. Optimization of biodiesel production from rice bran oil via ...

    African Journals Online (AJOL)

    ... 9,12-octadecadienoic and 9-octadecadienoic acid. The fourier transform infrared spectrum of biodiesel also showed the characteristic bands of C=O, O-C-O, C=C and –(CH2)n-. Key words: Rice bran oil, biodiesel, response surface methodology, gas chromatography mass spectrometry, fourier transform infrared spectrum ...

  11. Biodiesel by catalytic reactive distillation powered by metal oxides

    NARCIS (Netherlands)

    Kiss, A.A.; Dimian, A.C.; Rothenberg, G.

    2008-01-01

    The properties and use of biodiesel as a renewable fuel as well as the problems associated with its current production processes are outlined. A novel sustainable esterification process based on catalytic reactive distillation is proposed. The pros and cons of manufacturing biodiesel via fatty acid

  12. Rapid biodiesel production using wet microalgae via microwave irradiation

    International Nuclear Information System (INIS)

    Wahidin, Suzana; Idris, Ani; Shaleh, Sitti Raehanah Muhamad

    2014-01-01

    Highlights: • Lipid was directly extracted from wet microalgae using microwave irradiation. • The microwave irradiation and water bath-assisted solvent extraction are applied. • Cell walls are significantly disrupted under microwave irradiation. • Highly disrupted cell walls led to higher biodiesel yield in microwave irradiation. • Microwave irradiation is a promising direct technique with high biodiesel yields. - Abstract: The major challenges for industrial commercialized biodiesel production from microalgae are the high cost of downstream processing such as dewatering and drying, utilization of large volumes of solvent and laborious extraction processes. In order to address these issues the microwave irradiation method was used to produce biodiesel directly from wet microalgae biomass. This alternative method of biodiesel production from wet microalgae biomass is compared with the conventional water bath-assisted solvent extraction. The microwave irradiation extracted more lipids and high biodiesel conversion was obtained compared to the water bath-assisted extraction method due to the high cell disruption achieved and rapid transesterification. The total content of lipid extracted from microwave irradiation and water bath-assisted extraction were 38.31% and 23.01% respectively. The biodiesel produced using microwave irradiation was higher (86.41%) compared to the conventional method. Thus microwave irradiation is an attractive and promising technology to be used in the extraction and transesterification process for efficient biodiesel production

  13. Production and analysis of biodiesel from Jatropha curcas seed ...

    African Journals Online (AJOL)

    ADOWIE PERE

    glycerine to liquid fuel for blending gasoline as alternative engine fuel. Energy Convers. Manage. 41:1741-1748. Demirbas, A (2009) Production of biodiesel from algae oils, Energy Sources, Part A: Recovery,. Utilization, and Environmental Effects, 31: 163-. 168. Demirbas, A (2005) Biodiesel production from vegetable oils ...

  14. Moringa oleifera oil: Studies of characterization and biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    da Silva, Jhosianna P.V.; Serra, Tatiana M.; Meneghetti, Simoni M.P. [Universidade Federal de Alagoas, Instituto de Quimica e Biotecnologia, Laboratorio de Oleoquimica, Maceio, Alagoas, CEP 57072-970 (Brazil); Gossmann, Marcelo; Wolf, Carlos R.; Meneghetti, Mario R. [Universidade Luterana do Brasil, Instituto de Quimica, Canoas, Rio Grande do Sul, CEP 92420-280 (Brazil)

    2010-10-15

    This work describes studies with the seeds of Moringa oleifera (MO), obtained in the northeast of Brazil, evaluating some properties and chemical composition of the oil, as well any potential application in biodiesel production. The studied physicochemical properties of the MO biodiesel, suggest that this material may be used as fuel in diesel engines, mainly as a mixture to petrodiesel. (author)

  15. Enzymatic biodiesel production from sludge palm oil (SPO) using ...

    African Journals Online (AJOL)

    Biodiesel is a non-toxic, renewable and environmental friendly fuel. This study involved the production of biodiesel from sludge palm oil (SPO), a low-cost waste oil via enzymatic catalysis. The enzyme catalyst was a Candida cylindracea lipase, locally-produced using palm oil mill effluent as the low cost based medium.

  16. Assessment of Physicochemical Properties of Biodiesel from African ...

    African Journals Online (AJOL)

    The African Grape (Lannea microcarpa) seed oil was extracted and subjected to fuel properties tests according to standard method for oil and fuel analysis to evaluate its suitability as oil crop for biodiesel production in Nigeria. The oil was transesterified using alkali hydrolysis to biodiesel. The yields of the oil and its methyl ...

  17. SVOC emissions from diesel trucks operating of biodiesel fuels

    Science.gov (United States)

    The U.S. currently produces roughly 5 billion liters of biodiesel per year. Use of biodiesel is projected to increase based on its potential economic, energy, and environmental benefits. Despite these benefits, there is public health concern about the possible direct and indirect...

  18. Overview on the current trends in biodiesel production

    International Nuclear Information System (INIS)

    Yusuf, N.N.A.N.; Kamarudin, S.K.; Yaakub, Z.

    2011-01-01

    Research highlights: → Various method for the production of biodiesel from vegetable oil were reviewed. → Such as direct use and blending, microemulsion, pyrolysis and transesterification. → The advantages and disadvantages of the different biodiesel-production methods are also discussed. → Finally, the economics of biodiesel production was discussed using Malaysia as a case study. -- Abstract: The finite nature of fossil fuels necessitates consideration of alternative fuels from renewable sources. The term biofuel refers to liquid, gas and solid fuels predominantly produced from biomass. Biofuels include bioethanol, biomethanol, biodiesel and biohydrogen. Biodiesel, defined as the monoalkyl esters of vegetable oils or animal fats, is an attractive alternative fuel because it is environmentally friendly and can be synthesized from edible and non-edible oils. Here, we review the various methods for the production of biodiesel from vegetable oil, such as direct use and blending, microemulsion, pyrolysis and transesterification. The advantages and disadvantages of the different biodiesel-production methods are also discussed. Finally, we analyze the economics of biodiesel production using Malaysia as a case study.

  19. Biodiesel: A fuel, a lubricant, and a solvent

    Science.gov (United States)

    Biodiesel is well-known as a biogenic alternative to conventional diesel fuel derived from petroleum. It is produced from feedstocks such as plant oils consisting largely of triacylglycerols through transesterification with an alcohol such as methanol. The properties of biodiesel are largely compet...

  20. Biodiesel production--current state of the art and challenges.

    Science.gov (United States)

    Vasudevan, Palligarnai T; Briggs, Michael

    2008-05-01

    Biodiesel is a clean-burning fuel produced from grease, vegetable oils, or animal fats. Biodiesel is produced by transesterification of oils with short-chain alcohols or by the esterification of fatty acids. The transesterification reaction consists of transforming triglycerides into fatty acid alkyl esters, in the presence of an alcohol, such as methanol or ethanol, and a catalyst, such as an alkali or acid, with glycerol as a byproduct. Because of diminishing petroleum reserves and the deleterious environmental consequences of exhaust gases from petroleum diesel, biodiesel has attracted attention during the past few years as a renewable and environmentally friendly fuel. Since biodiesel is made entirely from vegetable oil or animal fats, it is renewable and biodegradable. The majority of biodiesel today is produced by alkali-catalyzed transesterification with methanol, which results in a relatively short reaction time. However, the vegetable oil and alcohol must be substantially anhydrous and have a low free fatty acid content, because the presence of water or free fatty acid or both promotes soap formation. In this article, we examine different biodiesel sources (edible and nonedible), virgin oil versus waste oil, algae-based biodiesel that is gaining increasing importance, role of different catalysts including enzyme catalysts, and the current state-of-the-art in biodiesel production.

  1. Investigating the Production of Biodiesel from Alphonso Mango ...

    African Journals Online (AJOL)

    This necessitated a three steps esterification of the oil sample for reduction of the %FFA to 0.547mgKOH/g and later transesterification of the oil. The effect of reaction temperature, reaction time and oil to methanol ratio on production of biodiesel from the oil was then investigated. Optimum yield of biodiesel from this oil were ...

  2. Production and characterization of biodiesel from the traditional ...

    African Journals Online (AJOL)

    As a result, acid pretreatment followed by base-catalyzed transesterification reaction was carried out to produce biodiesel. At the pretreatment stage, the acid value and FFA level were reduced to 3.93 mg KOH/g and 1.96%, respectively through sulfuric acid catalyzed esterification reaction. Key words: Animal fat, biodiesel, ...

  3. Biodiesel production from waste soybean oil biomass as renewable ...

    African Journals Online (AJOL)

    USER

    2010-07-05

    Jul 5, 2010 ... Uso de centrífugas para los procesos de biodiesel. Aceites Grasas, 13: 98-105. Hossain ABMS, Boyce AN (2009a). Biodiesel production from waste sunflower cooking oil as an environmental recycling process and renewable energy. Bulgarian J. Agric. Sci. 15(4): 313-318. Hossain ABMS, Boyce AN ...

  4. Production of biodiesel from Jatropha oil (Curcas Oil) | Oladeji ...

    African Journals Online (AJOL)

    This work deals with the production of Biodiesel from Jatropha oil also known as Curcas oil. Material used for the production was sourced for locally. Basic test for the suitability of the Jatropha oil was carried out in the lab. The test carried out to determine if the produced Biodiesel met standards set was carried out at the ...

  5. Biodiesel from Soybean Promotes Cell Proliferation in Vitro

    Science.gov (United States)

    Gioda, Adriana; Rodríguez-Cotto, Rosa I.; Amaral, Beatriz Silva; Encarnación-Medina, Jarline; Ortiz-Martínez, Mario G.; Jiménez-Vélez, Braulio D.

    2016-01-01

    Toxicological responses of exhaust emissions of biodiesel are different due to variation in methods of generation and the tested biological models. A chemical profile was generated using ICP-MS and GC-MS for the biodiesel samples obtained in Brazil. A cytotoxicity assay and cytokine secretion experiments were evaluated in human bronchial epithelial cells (BEAS-2B). Cells were exposed to polar (acetone) and nonpolar (hexane) extracts from particles obtained from fuel exhaust: fossil diesel (B5), pure soybean biodiesel (B100), soybean biodiesel with additive (B100A) and ethanol additive (EtOH). Biodiesel and its additives exhibited higher organic and inorganic constituents on particles when compared to B5. The biodiesel extracts did not exert any toxic effect at concentrations 10, 25, 50, 75, and 100 μg mL -1. In fact quite the opposite, a cell proliferation effect induced by the B100 and B100A extracts is reported. A small increase in concentrations of inflammatory mediators (Interleukin-6, IL-6; and Interleukin-8, IL-8) in the medium of biodiesel-treated cells was observed, however, no statistical difference was found. An interesting finding indicates that the presence of metals in the nonpolar (hexane) fraction of biodiesel fuel (B100) represses cytokine release in lung cells. This was revealed by the use of the metal chelator. Results suggest that metals associated with biodiesel’s organic constituents might play a significant role in molecular mechanisms associated to cellular proliferation and immune responses. PMID:27179667

  6. Pembuatan Biodiesel Secara Batch Dengan Memanfaatkan Gelombang Mikro (Microwave

    Directory of Open Access Journals (Sweden)

    Rhesa Purnama Putra

    2012-09-01

    Full Text Available Biodiesel merupakan bioenergi atau bahan bakar nabati yang dibuat dari minyak nabati, baik minyak baru atau bekas penggorengan melalui proses transesterifikasi, esterifikasi, atau proses esterifikasi-transesterifikasi. Tujuan penelitian ini adalah untuk membuat biodiesel dari minyak goreng secara batch melalui proses transesterifikasi dengan menggunakan radiasi mikrowave serta mempelajari berapa daya dan waktu optimal yang diperlukan untuk proses pembuatan biodiesel dengan radiasi microwave dengan katalis CaO, H2SO4, dan tanpa katalis. Dalam penelitian ini digunakan tiga variabel, yaitu daya (Watt;100,200,300,400, waktu (menit; 5,10,15,20 dan jenis katalis; CaO, H2SO4, dan tanpa katalis. Pada tahap persiapan menghitung volume minyak dan metanol yang akan dicampur. Kemudian mencampurnya didalam reaktor. Lalu mendinginkan campuran hingga terbentuk dua lapisan atas dan bawah dilanjutkan dengan melakukan pemisahan lapisan atas (biodiesel dari lapisan bawah (gliserol. Adapun pada tahap analisis, biodiesel hasil reaksi transesterfikasi dianalisa untuk mendapatkan data yield metil ester, densitas, viskositas, dan flash point. Dari penelitian diketahui bahwa hasil yang didapatkan masih belum dapat memenuhi standar biodiesel yang ditetapkan. Katalis CaO dapat memberikan hasil yang lebih baik dibandingkan dengan katalis H2SO4 dan tanpa katalis. Kondisi operasi untuk menghasilkan kualitas yield biodiesel terbaik yaitu pada daya 200 Watt selama 20 menit dengan menggunakan katalis CaO. Yield biodiesel terbesar didapatkan yield sebesar 60,11 %.

  7. A Comparative Characteristic Study of Jatropha and Cardanol Biodiesel Blends

    Science.gov (United States)

    Pugazhenthi, R.; Chandrasekaran, M.; Muthuraman, R. K.; Vivek, P.; Parthiban, A.

    2017-03-01

    The demand in fuel needs and the depleting fossil fuels raised the need towards bio-fuels. The emerging trend in research field is highly focused on biodiesel production and their characteristic analysis. Since pollution is a major threat to the environment, emission parameter analyses are much important to be concentrated. As the entire world contains plenty of biofuels, it is necessary to explore them for its efficiency and analyze their parameters. In this experimental work jatropha and cashew nut shell biodiesel (Cardanol) was extracted and they were blended with diesel. The characteristics of jatropha and cardanol biodiesel were studied in the DI diesel engine by varying the load at the same speed. In brief, this experimental analysis is carried out to compare the emission characteristics between Jatropha biodiesel at 20% (B20) and 40% (B40) and Cardanol biodiesel blends at 20% (C20) and 40% (C40).

  8. Comparison between conventional and ultrasonic preparation of beef tallow biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Teixeira, Leonardo S.G. [Instituto de Quimica - Universidade Federal da Bahia, Campus Universitario de Ondina, 40.170-280 - Salvador, Bahia (Brazil); Assis, Julio C.R.; Santos, Iran T.V.; Guimaraes, Paulo R.B.; Pontes, Luiz A.M. [Universidade Salvador - UNIFACS - Departamento de Engenharia e Arquitetura, - Av. Cardeal da Silva 132, 40.220-141 - Salvador, Bahia (Brazil); Mendonca, Daniel R. [Escola Politecnica - Universidade Federal da Bahia, Av. Aristides Novis 2, 40.210-630, Salvador, Bahia (Brazil); Teixeira, Josanaide S.R. [Instituto Federal de Educacao Ciencia e Tecnologica da Bahia - IFBAHIA - Rua Emidio de Morais S/N, 40.625-650, Salvador - BA (Brazil)

    2009-09-15

    Tallow is biodiesel feedstock that, due to its highly centralized generation in slaughter/processing facilities and historically low prices, may have energetic, environmental, and economic advantages that could be exploited. Transesterification of fatty acids by means of ultrasonic energy has been used for biodiesel production from different vegetable oils. However, application of ultrasonic irradiation for biodiesel production from beef tallow has received little attention. In this work, the transesterification of beef tallow with methanol was performed in the presence of potassium hydroxide as a catalyst using ultrasound irradiation (400 W, 24 kHz). The reaction time, conversion and biodiesel quality were compared with that seen in conventional transesterification. The results indicated that the reaction conversion and biodiesel quality were similar; however, the use of ultrasonic irradiation decreased the reaction time, showing that this method may be a promising alternative to the conventional method. (author)

  9. Comparison between conventional and ultrasonic preparation of beef tallow biodiesel

    International Nuclear Information System (INIS)

    Teixeira, Leonardo S.G.; Assis, Julio C.R.; Santos, Iran T.V.; Guimaraes, Paulo R.B.; Pontes, Luiz A.M.; Mendonca, Daniel R.; Teixeira, Josanaide S.R.

    2009-01-01

    Tallow is biodiesel feedstock that, due to its highly centralized generation in slaughter/processing facilities and historically low prices, may have energetic, environmental, and economic advantages that could be exploited. Transesterification of fatty acids by means of ultrasonic energy has been used for biodiesel production from different vegetable oils. However, application of ultrasonic irradiation for biodiesel production from beef tallow has received little attention. In this work, the transesterification of beef tallow with methanol was performed in the presence of potassium hydroxide as a catalyst using ultrasound irradiation (400 W, 24 kHz). The reaction time, conversion and biodiesel quality were compared with that seen in conventional transesterification. The results indicated that the reaction conversion and biodiesel quality were similar; however, the use of ultrasonic irradiation decreased the reaction time, showing that this method may be a promising alternative to the conventional method. (author)

  10. Use of Reactive Distillation for Biodiesel Production: A Literature Survey

    Directory of Open Access Journals (Sweden)

    Muhammad Dani Supardan

    2006-06-01

    Full Text Available Biodiesel has been shown to be the best substitute for fossil-based fuels to its environmental advantages and renewable resource availability. There is a great demand for the commercialization of biodiesel production, which in turn calls for a technically and economically reactor technology. The production of biodiesel in existing batch and continuous-flow processes requires excess alcohol, typically 100%, over the stoichiometric molar requirement in order to drive the chemical reaction to completion. In this study, a novel reactor system using a reactive distillation (RD technique was discussed for biodiesel production. RD is a chemical unit operation in which chemical reactions and separations occur simultaneously in one unit. It is an effective alternative to the classical combination of reactor and separation units especially when involving reversible or consecutive chemical reactions such as transesterication process in biodiesel production.

  11. Studies of Terminalia catappa L. oil: characterization and biodiesel production.

    Science.gov (United States)

    Dos Santos, I C F; de Carvalho, S H V; Solleti, J I; Ferreira de La Salles, W; Teixeira da Silva de La Salles, K; Meneghetti, S M P

    2008-09-01

    Since the biodiesel program has been started in Brazil, the investigation of alternative sources of triacylglycerides from species adapted at semi-arid lands became a very important task for Brazilian researchers. Thus we initiated studies with the fruits of the Terminalia catappa L (TC), popularly known in Brazil as "castanhola", evaluating selected properties and chemical composition of the oil, as well any potential application in biodiesel production. The oil was obtained from the kernels of the fruit, with yields around 49% (% mass). Also, its fatty acid composition was quite similar to that of conventional oils. The crude oil of the TC was transesterified, using a conventional catalyst and methanol to form biodiesel. The studied physicochemical properties of the TC biodiesel are in acceptable range for use as biodiesel in diesel engines.

  12. Enzymatic transesterification of lipids from microalgae into biodiesel: a review

    Directory of Open Access Journals (Sweden)

    Maria del Pilar Rodriguez

    2016-10-01

    Full Text Available Biodiesel is considered as a potential interesting alternative diesel substitute due to its many advantages, such as biodegradability and non-toxicity. Biodiesel production worldwide is low and does not meet the needs of society. Therefore, biodiesel production policies have been implemented by various countries. This paper addresses the issues of plant materials containing lipids for biodiesel production and explores also the avenue of microalgae as an alternative. Various conversion technologies of lipids into biodiesel are also described and compared. Enzymatic transesterification would be most appropriate when microalgae oils are used because of their high free fatty acids content. The optimization of the enzymatic process depends on several parameters such as the catalyst, temperature, reaction time and the alcohol: oil molar ratio.

  13. Assessing the greenhouse gas emissions from poultry fat biodiesel

    DEFF Research Database (Denmark)

    Jørgensen, Andreas; Bikker, Paul; Herrmann, Ivan Tengbjerg

    2012-01-01

    This article attempts to answer the question: What will most likely happen in terms of emitted greenhouse gases if the use of poultry fat for making biodiesel used in transportation is increased? Through a well-to-wheel assessment, several different possible scenarios are assessed, showing...... that under average conditions, the use of poultry fat biodiesel instead of diesel leads to a slight reduction (6%) in greenhouse gas emissions. The analysis shows that poultry fat is already used for different purposes and using poultry fat for biodiesel will therefore remove the poultry fat from its...... original use. This implies that even though the use of biodiesel is assumed to displace petrochemical diesel, the ‘original user’ of the poultry fat will have to find a substitute, whose production leads to a greenhouse gas emissions comparable to what is saved through driving on poultry fat biodiesel...

  14. Heterogeneous catalysis afford biodiesel of babassu, castor oil and blends

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Lee M.G. de; Abreu, Wiury C. de; Silva, Maria das Gracas de O. e; Matos, Jose Milton E. de; Moura, Carla V.R. de; Moura, Edmilson M. de, E-mail: mmoura@ufpi.edu.br [Universidade Federal do Piaui (UFPI), Teresina, PI (Brazil). Departamento de Quimica; Lima, Jose Renato de O.; Oliveira, Jose Eduardo de [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP/IQ/CEMPEQC), Araraquara, SP (Brazil). Instituto de Quimica. Centro de Monitoramento e Pesquisa da Qualidade de Combustiveis, Biocombustiveis, Petroleo e Derivados

    2013-04-15

    This work describes the preparation of babassu, castor oil biodiesel and mixtures in various proportions of these oils, using alkaline compounds of strontium (SrCO{sub 3} + SrO + Sr (OH){sub 2}) as heterogeneous catalysts. The mixture of oils of these oleaginous sources was used in the production of biodiesel with quality parameters that meet current legislation. The catalyst was characterized by X-ray diffractometry (XDR), physisorption of gas (BET method), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDX) and Fourier transform infrared spectroscopy (FTIR). The viscometric technique was used to monitor the optimization.The transesterification reactions performed using strontium compounds reached conversion rates of 97.2% babassu biodiesel (BB), 96.4% castor oil biodiesel (COB) and 95.3% Babassu/Castor Oil Biodiesel 4:1 (BBCO41). (author)

  15. Heterogeneous catalysis afford biodiesel of babassu, castor oil and blends

    International Nuclear Information System (INIS)

    Carvalho, Lee M.G. de; Abreu, Wiury C. de; Silva, Maria das Gracas de O. e; Matos, Jose Milton E. de; Moura, Carla V.R. de; Moura, Edmilson M. de; Lima, Jose Renato de O.; Oliveira, Jose Eduardo de

    2013-01-01

    This work describes the preparation of babassu, castor oil biodiesel and mixtures in various proportions of these oils, using alkaline compounds of strontium (SrCO 3 + SrO + Sr (OH) 2 ) as heterogeneous catalysts. The mixture of oils of these oleaginous sources was used in the production of biodiesel with quality parameters that meet current legislation. The catalyst was characterized by X-ray diffractometry (XDR), physisorption of gas (BET method), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDX) and Fourier transform infrared spectroscopy (FTIR). The viscometric technique was used to monitor the optimization.The transesterification reactions performed using strontium compounds reached conversion rates of 97.2% babassu biodiesel (BB), 96.4% castor oil biodiesel (COB) and 95.3% Babassu/Castor Oil Biodiesel 4:1 (BBCO41). (author)

  16. Uso da cromatografia gasosa bidimensional abrangente (GC×GC na caracterização de misturas biodiesel/diesel: aplicação ao biodiesel de sebo bovino

    Directory of Open Access Journals (Sweden)

    Maria Silvana A Moraes

    2011-01-01

    Full Text Available The growth of biodiesel market and the implementation of regulations related to biodiesel production and biodiesel/diesel blending has encouraged the development of appropriate analytical methods to control the composition of this type of mixture. In this study, an evaluation of the potential of GC×GC for the characterization of samples of beef tallow biodiesel and the composition of blends of biodiesel/diesel is presented. The methodology was applied to beef tallow biodiesel and its mixtures with petrodiesel, ranging from B2 to B50. Results allowed not only the identification and quantification of the biodiesel esters, but also the biodiesel percentage in biodiesel/diesel blends.

  17. Antioxidant Effect on Oxidation Stability of Blend Fish Oil Biodiesel with Vegetable Oil Biodiesel and Petroleum Diesel Fuel

    Directory of Open Access Journals (Sweden)

    M. Hossain

    2013-06-01

    Full Text Available Two different phenolic synthetic antioxidants were used to improve the oxidation stability of fish oil biodiesel blends with vegetable oil biodiesel and petroleum diesel. Butylhydroxytoluene (BHT most effective for improvement of the oxidation stability of petro diesel, whereas  tert-butylhydroquinone (TBHQ showed good performance in fish oil biodiesel. Fish oil/Rapeseed oil biodiesel mixed showed some acceptable results in higher concentration ofantioxidants. TBHQ showed better oxidation stability than BHT in B100 composition. In fish oil biodiesel/diesel mixed fuel, BHT was more effective antioxidant than TBHQ to increase oxidationstability because BHT is more soluble than TBHQ. The stability behavior of biodiesel/diesel blends with the employment of the modified Rancimat method (EN 15751. The performance ofantioxidants was evaluated for treating fish oil biodiesel/Rapeseed oil biodiesel for B100, and blends with two type diesel fuel (deep sulfurization diesel and automotive ultra-low sulfur or zero sulfur diesels. The examined blends were in proportions of 5, 10, 15, and 20% by volume of fish oilbiodiesel.

  18. Production possibility frontier analysis of biodiesel from waste cooking oil

    International Nuclear Information System (INIS)

    Kagawa, Shigemi; Takezono, Kanako; Suh, Sangwon; Kudoh, Yuki

    2013-01-01

    This paper presents an assessment of the productive efficiency of an advanced biodiesel plant in Japan using Data Envelopment Analysis (DEA). The empirical analysis uses monthly input data (waste cooking oil, methanol, potassium hydroxide, power consumption, and the truck diesel fuel used for the procurement of waste cooking oil) and output data (biodiesel) of a biodiesel fuel plant for August 2008–July 2010. The results of this study show that the production activity with the lowest cost on the biodiesel production possibility frontier occurred in March 2010 (production activity used 1.41 kL of waste cooking oil, 0.18 kL of MeOH, 16.33 kg of KOH, and 5.45 kW h of power), and the unit production cost in that month was 18,517 yen/kL. Comparing this efficient production cost to the mean unit production cost on the production possibility frontier at 19,712 yen/kL, revealed that the cost of producing 1 kL of biodiesel could be reduced by as much as 1195 yen. We also find that the efficiency improvement will contribute to decreasing the cost ratio (cost per sale) of the biodiesel production by approximately 1% during the study period (24 months) between August 2008 and July 2010. - Highlights: ► This paper analyzes the productive efficiency of an advanced biodiesel plant using DEA. ► We examine the optimal production activities of biodiesel from waste cooking oil. ► Considering the production frontier, the unit cost of biodiesel could be reduced by 1195 yen. ► The efficiency improvement contributes to decreasing the cost ratio of the biodiesel by 1%

  19. Biodiesel dari Minyak Buta-Buta (Hura Crepitans Linn) dengan Menggunakan Katalis Ni/Lempung

    OpenAIRE

    Simatupang, Ekadian Lestari; Bahri, Syaiful; Saputra, Edy

    2017-01-01

    Biodiesel is one of the alternative fuels as a substitute for fossil fuels synthesised from the transesterification reaction. The process of making biodiesel which using a homogeneous catalyst is costly for product separation process. Thus use of heterogeneous catalysts such as Ni/Clay catalyst was developed. This study aims to produce biodiesel from Hura crepitans Linn oil to determine best conditions of making biodiesel, determine the physical andchemical properties of biodiesel produced an...

  20. Western Kentucky University Research Foundation Biodiesel Project

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Wei-Ping [Principal Investigator; Cao, Yan [Co-Principal Investigator

    2013-03-15

    Petroleum-based liquid hydrocarbons is exclusively major energy source in the transportation sector. Thus, it is the major CO{sub 2} source which is the associated with greenhouse effect. In the United States alone, petroleum consumption in the transportation sector approaches 13.8 million barrels per day (Mbbl/d). It is corresponding to a release of 0.53 gigatons of carbon per year (GtC/yr), which accounts for approximate 7.6 % of the current global release of CO{sub 2} from all of the fossil fuel usage (7 GtC/yr). For the long term, the conventional petroleum production is predicted to peak in as little as the next 10 years to as high as the next 50 years. Negative environmental consequences, the frequently roaring petroleum prices, increasing petroleum utilization and concerns about competitive supplies of petroleum have driven dramatic interest in producing alternative transportation fuels, such as electricity-based, hydrogen-based and bio-based transportation alternative fuels. Use of either of electricity-based or hydrogen-based alternative energy in the transportation sector is currently laden with technical and economical challenges. The current energy density of commercial batteries is 175 Wh/kg of battery. At a storage pressure of 680 atm, the lower heating value (LHV) of H{sub 2} is 1.32 kWh/liter. In contrast, the corresponding energy density for gasoline can reach as high as 8.88 kWh/liter. Furthermore, the convenience of using a liquid hydrocarbon fuel through the existing infrastructures is a big deterrent to replacement by both batteries and hydrogen. Biomass-derived ethanol and bio-diesel (biofuels) can be two promising and predominant U.S. alternative transportation fuels. Both their energy densities and physical properties are comparable to their relatives of petroleum-based gasoline and diesel, however, biofuels are significantly environmental-benign. Ethanol can be made from the sugar-based or starch-based biomass materials, which is easily

  1. Production of Biodiesels from Multiple Feedstocks and Properties of Biodiesels and Biodiesel/Diesel Blends: Final Report; Report 1 in a Series of 6

    Energy Technology Data Exchange (ETDEWEB)

    Kinast, J. A.

    2003-03-01

    In a project sponsored by the National Renewable Energy Laboratory, the Institute of Gas Technology is conducting an investigation of biodiesels produced from vegetable and animal based feedstocks. This subcontract report presents their findings.

  2. Biodiesel II: A new concept of biodiesel production - transesterification with supercritical methanol

    Directory of Open Access Journals (Sweden)

    Skala Dejan U.

    2004-01-01

    Full Text Available Biodiesel is defined as a fuel that might be used as a pure biofuel or at high concentration in mineral oil derivatives, in accordance with specific quality standards for transport applications. The main raw material used for biodiesel production is rapeseed, which contains mono-unsaturated (about 60% and also, in a lower quantity, poly-unsaturated fatty acids (C 18:1 and C 18:3, as well as some amounts of undesired saturated fatty acids (palmitic and stearic acids. Other raw materials have also been used in the research and industrial production of biodiesel (palm-oil, sunflower-oil, soybean-oil, waste plant oil, animal fats, etc. The historical background of the biodiesel production, installed industrial capacities, as well as Directives of the European Parliament and of the Council (May 2003 regarding the promotion of the use of biofuels or other renewable fuels for transport are discussed in the first part of this article (Chem. Ind. 58 (2004. The second part focused on some new concepts and the future development of technology for biodiesel production based on the use of non-catalytic transesterification under supercritical conditions. A literature review, as well as original results based on the transesterification of animal fats, plant oil and used plant oil were discussed. Obtained results were compared with the traditional concept of transesterification based on base or acid catalysis. Experimental investigations of transesterification with supercritical methanol were performed in a 2 dm3 autoclave at 140 bar pressure and at 300°C with molar ratio of methanol to triglycerides of about 41. The degree of esterification strongly depends on the density of supercritical methanol and on the possibility of reaction occurring in one phase.

  3. Performance Evaluation of Palm Oil as Biodiesel

    OpenAIRE

    Sunday A. LAWAL; Ahmed BABAKANO

    2011-01-01

    This work involved the production of diesel from most commonly available palm fruits oil Pisifera elaeis guineensis and testing for the brake power, torque of an engine and specific fuel consumption of a conventional diesel engine utilizing the produced diesel from palm oil. The obtained results were compared with those for fossil diesel fuel. The results show that the value of brake power was 6927.21W for fossil diesel while that of biodiesel was 7135.02W. Similarly the value for brake torqu...

  4. Carbonyl emissions in diesel and biodiesel exhaust

    Science.gov (United States)

    Machado Corrêa, Sérgio; Arbilla, Graciela

    With the use of biodiesel in clear growth, it is important to quantify any potential emission benefits or liabilities of this fuel. Several researches are available concerning the regulated emissions of biodiesel/diesel blends, but there is a lack of information about non-regulated emissions. In a previous paper [Corrêa, S.M., Arbilla, G., 2006. Emissões de formaldeído e acetaldeído de misturas biodiesel/diesel. Periódico Tchê Química, 3, 54-68], the emissions of aromatic hydrocarbons were reported. In this work, seven carbonyl emissions (formaldehyde, acetaldehyde, acrolein, acetone, propionaldehyde, butyraldehyde, and benzaldehyde) were evaluated by a heavy-duty diesel engine fueled with pure diesel (D) and biodiesel blends (v/v) of 2% (B2), 5% (B5), 10% (B10), and 20% (B20). The tests were conducted using a six cylinder heavy-duty engine, typical of the Brazilian fleet of urban buses, in a steady-state condition under 1000, 1500, and 2000 rpm. The exhaust gases were diluted nearly 20 times and the carbonyls were sampled with SiO 2-C18 cartridges, impregnated with acid solution of 2,4-dinitrophenylhydrazine. The chemical analyses were performed by high performance liquid chromatography using UV detection. Using average values for the three modes of operation (1000, 1500, and 2000 rpm) benzaldehyde showed a reduction on the emission (-3.4% for B2, -5.3% for B5, -5.7% for B10, and -6.9% for B20) and all other carbonyls showed a significative increase: 2.6, 7.3, 17.6, and 35.5% for formaldehyde; 1.4, 2.5, 5.4, and 15.8% for acetaldehyde; 2.1, 5.4, 11.1, and 22.0% for acrolein+acetone; 0.8, 2.7, 4.6, and 10.0% for propionaldehyde; 3.3, 7.8, 16.0, and 26.0% for butyraldehyde.

  5. Improved Soybean Oil for Biodiesel Fuel

    Energy Technology Data Exchange (ETDEWEB)

    Tom Clemente; Jon Van Gerpen

    2007-11-30

    The goal of this program was to generate information on the utility of soybean germplasm that produces oil, high in oleic acid and low in saturated fatty acids, for its use as a biodiesel. Moreover, data was ascertained on the quality of the derived soybean meal (protein component), and the agronomic performance of this novel soybean germplasm. Gathering data on these later two areas is critical, with respect to the first, soybean meal (protein) component is a major driver for commodity soybean, which is utilized as feed supplements in cattle, swine, poultry and more recently aquaculture production. Hence, it is imperative that the resultant modulation in the fatty acid profile of the oil does not compromise the quality of the derived meal, for if it does, the net value of the novel soybean will be drastically reduced. Similarly, if the improved oil trait negative impacts the agronomics (i.e. yield) of the soybean, this in turn will reduce the value of the trait. Over the course of this program oil was extruded from approximately 350 bushels of soybean designated 335-13, which produces oil high in oleic acid (>85%) and low in saturated fatty acid (<6%). As predicted improvement in cold flow parameters were observed as compared to standard commodity soybean oil. Moreover, engine tests revealed that biodiesel derived from this novel oil mitigated NOx emissions. Seed quality of this soybean was not compromised with respect to total oil and protein, nor was the amino acid profile of the derived meal as compared to the respective control soybean cultivar with a conventional fatty acid profile. Importantly, the high oleic acid/low saturated fatty acids oil trait was not impacted by environment and yield was not compromised. Improving the genetic potential of soybean by exploiting the tools of biotechnology to improve upon the lipid quality of the seed for use in industrial applications such as biodiesel will aid in expanding the market for the crop. This in turn, may

  6. Prospects of dedicated biodiesel engine vehicles in Malaysia and Indonesia

    International Nuclear Information System (INIS)

    Jayed, M.H.; Masjuki, H.H.; Kalam, M.A.; Mahlia, T.M.I.; Liaquat, A.M.; Husnawan, M.

    2011-01-01

    Petro diplomacy has played its role in last few decades and that makes energy security a major concern worldwide. Rapid climate change and environmental protection is another vital issue to be addressed in recent energy policies. So an alternative carbon neutral transport fuel is a must in new sustainable energy mix. Biodiesel has immense potentiality to be a part of a sustainable energy mix. In this energy scenario, Brazil's success is a role model in utilizing its agro-industry for reducing poverty, greenhouse gas emission and petro-dependency simultaneously. Brazil commercialized bioethanol in mass scale by introducing flexible fuel vehicles in market. This dedicated engine idea moralizes a new concept of dedicated biodiesel engine vehicles for Malaysia and Indonesia. Southeast Asian countries, i.e. Malaysia and Indonesia is the largest producer as well as exporter of palm oil. Growing at highest yield rate among other biodiesel feedstock, palm based biodiesel is a top exported product for this region. This paper will quantify the prospects of a dedicated biodiesel engine vehicle for Malaysia and Indonesia that will initiate palm based biodiesel in fuel supply chain by leapfrogging the barriers of biodiesel utilization by boosting local automobile industry simultaneously. This article will also review on energy scenario of Malaysia and Indonesia and their renewable energy policies and challenges for coming decades. (author)

  7. Methanolysis of Carica papaya Seed Oil for Production of Biodiesel

    Directory of Open Access Journals (Sweden)

    Foluso O. Agunbiade

    2014-01-01

    Full Text Available The future of fossil fuel sources of energy has necessitated the need to search for renewable alternatives. Thus, Carica papaya seed oil (CPSO was employed as feedstock for the production of biodiesel by methanolysis. The seed was obtained locally, dried, and extracted with n-hexane. The CPSO was analyzed for specific gravity, viscosity, iodine value, and saponification value, among others using standard methods. The oil was transesterified by two-stage catalysis with oil to methanol mole ratio of 1 : 9. The biodiesel produced was subjected to standard fuel tests. The seed has an oil yield of 31.2% which is commercially viable. The kinematic viscosity of the oil at 313 K was 27.4 mm2s−1 while that of Carica papaya oil methylester (CPOME was reduced to 3.57 mm2s−1 and the specific gravity was 0.84 comparable with other seed-oil biodiesels and number 2 diesel. Other oil properties were compared favourably with seed oils already documented for biodiesel synthesis. CPOME’s cloud and pour points were 275 K and 274 K, respectively, and relatively higher than other biodiesels and number 2 diesel. CPOME exhibits moderate corrosion of copper strip. The methanolysis improved the fuel properties of the CPOME similar to other biodiesels. CPSO therefore exhibits a potential for biodiesel production.

  8. Performance evaluation of diesel engine using rice bran biodiesel

    Directory of Open Access Journals (Sweden)

    Mayank Chhabra

    2017-06-01

    Full Text Available The consumption of fuels in the world is increasing rapidly and it affects the global economy of all the countries so this factor forced all the countries to find the alternative fuel to reduce and even replace the usage of petroleum. Thus use of biodiesel from non-edible oil sources serves as an alternative to this problem. The present study focuses on impact assessment of rice bran and crude rice bran biodiesel and its blends with diesel on diesel engine performance. The experimental investigation provides in depth detail of the biodiesel production process, evaluation of fuel properties and impact on engine performance. The study also investigates the optimization of the Compression ratio (CR of a compression ignition engine fueled with blends of biodiesel. In order to find out the optimum CR of the engine, experiments were conducted at different CRs ranging from 12 to 18. Then the experiments were conducted using B10, B20 and B40 blends of crude rice bran bio-diesel and diesel at CR of 12 and 14 and these results were compared with the results obtained when the same engine was tested on conventional diesel fuel. Similarly the experimental results of B10, B20 and B40 blends of rice bran bio-diesel at CR 14 were investigated and analyzed. Based on the experimental investigation the blends of crude rice bran bio-diesel can be used as fuel in diesel engine without making any modification to the diesel engine.

  9. Spontaneous ignition of biodiesel: A potential fire risk

    Directory of Open Access Journals (Sweden)

    Shibata Yasuhito

    2008-01-01

    Full Text Available The spontaneous ignition of biodiesel was for the first time suspected to be the cause of a recent fire in Japan. We herein present experimental evidence implying this potential risk of biodiesel. Thus, three independent biodiesel samples were subjected to a series of experiments, including a thermogravimetry-differential thermal analysis, a differential scanning calorimetry analysis and a modified wire basket test. The results were comparatively evaluated with reference to vegetable oils, of which spontaneous ignition has been well reported as a cause of fires. The heat onset temperature of biodiesel samples was determined to be ~100 °C, which was ~45 °C lower than those of vegetable oils. Furthermore, under the isothermal condition at 100 °C, the inner temperature of biodiesel samples rose rapidly with the generation of smoke after short induction periods owing to their exothermal decomposition, whereas for vegetable oils neither change in the inside temperature nor generation of smoke was observed even after 10 hours. It was therefore concluded that biodiesel possesses the higher risk of spontaneous ignition than vegetable oils. This is very important information to minimize the fire risk in biodiesel production facilities and so on. .

  10. Prospects of dedicated biodiesel engine vehicles in Malaysia and Indonesia

    Energy Technology Data Exchange (ETDEWEB)

    Jayed, M.H.; Masjuki, H.H.; Kalam, M.A.; Mahlia, T.M.I.; Liaquat, A.M. [Centre for Energy Sciences, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Husnawan, M. [Centre for Energy Sciences, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Department of Mechanical Engineering University of Syiah Kuala, Jl. S. Abd. Rauf No. 7, Darussalam - Banda Aceh (Indonesia)

    2011-01-15

    Petro diplomacy has played its role in last few decades and that makes energy security a major concern worldwide. Rapid climate change and environmental protection is another vital issue to be addressed in recent energy policies. So an alternative carbon neutral transport fuel is a must in new sustainable energy mix. Biodiesel has immense potentiality to be a part of a sustainable energy mix. In this energy scenario, Brazil's success is a role model in utilizing its agro-industry for reducing poverty, greenhouse gas emission and petro-dependency simultaneously. Brazil commercialized bioethanol in mass scale by introducing flexible fuel vehicles in market. This dedicated engine idea moralizes a new concept of dedicated biodiesel engine vehicles for Malaysia and Indonesia. Southeast Asian countries, i.e. Malaysia and Indonesia is the largest producer as well as exporter of palm oil. Growing at highest yield rate among other biodiesel feedstock, palm based biodiesel is a top exported product for this region. This paper will quantify the prospects of a dedicated biodiesel engine vehicle for Malaysia and Indonesia that will initiate palm based biodiesel in fuel supply chain by leapfrogging the barriers of biodiesel utilization by boosting local automobile industry simultaneously. This article will also review on energy scenario of Malaysia and Indonesia and their renewable energy policies and challenges for coming decades. (author)

  11. Biodiesel production methods of rubber seed oil: a review

    Science.gov (United States)

    Ulfah, M.; Mulyazmi; Burmawi; Praputri, E.; Sundari, E.; Firdaus

    2018-03-01

    The utilization of rubber seed as raw material of biodiesel production is seen highly potential in Indonesia. The availability of rubber seeds in Indonesia is estimated about 5 million tons per annum, which can yield rubber seed oil about 2 million tons per year. Due to the demand of edible oils as a food source is tremendous and the edible oil feedstock costs are far expensive to be used as fuel, production of biodiesel from non-edible oils such as rubber seed is an effective way to overcome all the associated problems with edible oils. Various methods for producing biodiesel from rubber seed oil have been reported. This paper introduces an optimum condition of biodiesel production methods from rubber seed oil. This article was written to be a reference in the selection of methods and the further development of biodiesel production from rubber seed oil. Biodiesel production methods for rubber seed oils has been developed by means of homogeneous catalysts, heterogeneous catalysts, supercritical method, ultrasound, in-situ and enzymatic processes. Production of biodiesel from rubber seed oil using clinker loaded sodium methoxide as catalyst is very interesting to be studied and developed further.

  12. A comprehensive review on biodiesel purification and upgrading

    Directory of Open Access Journals (Sweden)

    Hamed Bateni

    2017-09-01

    Full Text Available Serious environmental concerns regarding the use of fossil-based fuels have raised awareness regarding the necessity of alternative clean fuels and energy carriers. Biodiesel is considered a clean, biodegradable, and non-toxic diesel substitute produced via the transesterification of triglycerides with an alcohol in the presence of a proper catalyst. After initial separation of the by-product (glycerol, the crude biodiesel needs to be purified to meet the standard specifications prior to marketing. The presence of impurities in the biodiesel not only significantly affects its engine performance but also complicates its handling and storage. Therefore, biodiesel purification is an essential step prior to marketing. Biodiesel purification methods can be classified based on the nature of the process into equilibrium-based, affinity-based, membrane-based, reaction-based, and solid-liquid separation processes. The main adverse properties of biodiesel – namely moisture absorption, corrosiveness, and high viscosity – primarily arise from the presence of oxygen. To address these issues, several upgrading techniques have been proposed, among which catalytic (hydrodeoxygenation using conventional hydrotreating catalysts, supported metallic materials, and most recently transition metals in various forms appear promising. Nevertheless, catalyst deactivation (via coking and/or inadequacy of product yields necessitate further research. This paper provides a comprehensive overview on the techniques and methods used for biodiesel purification and upgrading.

  13. Development of Brazilian Biodiesel Sector from the Perspective of Stakeholders

    Directory of Open Access Journals (Sweden)

    Bárbara Françoise Cardoso

    2017-03-01

    Full Text Available In Brazil, the main program with respect to biodiesel is the National Program of Biodiesel Production and Use (NPBP. It is also considered the regulation mark of biodiesel production in Brazil and its directives are social inclusion and regional development. Considering these directives, this paper aims to analyse the perspective of biodiesel sector stakeholders in Brazil to understand whether NPBP directives are in consonance with the reality of the sector for its development. A questionnaire was created with 48 questions in order to understand the importance of 13 variables for the stakeholders, and the responses were treated by factor analysis (FA. The results showed the existence of a trade-off related to technological advances in biodiesel production that confronts NPBP directives, that is, the biodiesel sector tends not to evolve in terms of the use of advanced technologies. If policies change so as to develop the biodiesel sector using advanced technologies, NPBP should change its directives in order to involve family farmers in another way in the Brazilian economy.

  14. Production of Biodiesel from Vegetable Oil Using Microware Irradiation

    Directory of Open Access Journals (Sweden)

    N. Kapilan

    2012-01-01

    Full Text Available The petroleum oil supply crisis, the increase in demand and the price eruption have led to a search for an alternative fuel of bio-origin in India. Among the alternative fuels, biodiesel is considered as a sustainable renewable alternative fuel to fossil diesel. Non-edible jatropha oil has considerable potential for the production of biodiesel in India. The production of biodiesel from jatropha oil using a conventional heating method takes more than 1h. In this work, microwave irradiation has been used as a source of heat for the transesterification reaction. A domestic microwave oven was modified and used for microwave heating of the reactants. The time taken for biodiesel production using microwave irradiation was 1 min. The fuel property analysis shows that the properties of jatropha oil biodiesel satisfy the biodiesel standards, and are close to the fossil diesel standards. From this work, it is concluded that biodiesel can be produced from vegetable oil using microwave irradiation, with a significant reduction in production time.

  15. [Progress on biodiesel production with enzymatic catalysis in China].

    Science.gov (United States)

    Tan, Tianwei; Lu, Jike; Nie, Kaili; Zhang, Haixia; Deng, Li; Wang, Fang

    2010-07-01

    This paper reports the progress of biodiesel production with enzymatic catalysis in Beijing University of Chemical Technology, one of the leaders in biodiesel R & D in China, which includes screening of high-yield lipase production strains, optimization and scale-up of the lipase fermentation process, lipase immobilization, bioreactor development and scale-up, biodiesel separation and purification and the by-product glycerol utilization. Firstly, lipase fermentation was carried out at industrial scale with the 5 m3 stirred tank bioreactor, and the enzyme activity as high as 8 000 IU/mL was achieved by the species Candida sp. 99-125. Then, the lipase was purified and immobilized on textile membranes. Furthermore, biodiesel production was performed in the 5 m3 stirred tank bioreactor with an enzyme dosage as low as 0.42%, and biodiesel that met the German biodiesel standard was produced. And in the meantime, the byproduct glycerol was used for the production of 1,3-propanediol to partly offset the production cost of biodiesel, and 76.1 g/L 1,3-propanediol was obtained in 30 L fermentor with the species Klebsiella pneumoniae.

  16. Assessment of boundary lubrication in biodiesels by nanotribological tests

    International Nuclear Information System (INIS)

    Maru, Marcia M.; Almeida, Clara M.; Silva, Rui F.; Achete, Carlos A.

    2013-01-01

    Nanoscale measurements using atomic force microscopy are performed in order to scrutinize the friction phenomena observed in microscale ball-on-disc tribological tests under (boundary lubrication) BL regime. Two reference biodiesels, one derived from a vegetable source (soybean) and the other from animal fat, are compared. A linear dependence of the friction coefficient (μ) with the Stribeck parameter (S = viscosity × velocity/load) is observed: μ = 0.11 − 26.54 × S for the animal fat and μ = 0.12 − 51.56 × S for the soybean biodiesel. The nanotribological tests allowed highlighting the cohesion component of friction force in the BL regime that is associated to the intrinsic characteristics of the biodiesels, the respective friction coefficients being μ = 0.0206 for the animal fat and μ = 0.0233 for the soybean biodiesel. The better lubricity of the animal fat biodiesel compared to the soybean observed in microscale is attributed to the presence of sulfur and to the higher amount of mono- and di-glycerides contaminants in it. The polarity and/or chemical affinity of the respective sulfur and OH groups facilitate them to reacting with the steel surfaces during the rubbing action. At nanoscale level, the same ranking in friction is observed among the biodiesels, being that here the friction phenomena are attributed to the cohesive forces other than those related to viscosity. - Highlights: • The frictional behavior of standard reference biodiesels is studied. • Nanotribology tests help scrutinizing microscale friction in boundary lubrication. • AFM tests allowed highlighting the cohesion component of friction in the BL regime. • Animal fat biodiesel promotes lower and more stable friction than soybean biodiesel

  17. Production and characterization of biodiesel from Camelus dromedarius (Hachi) fat

    International Nuclear Information System (INIS)

    Sbihi, Hassen Mohamed; Nehdi, Imededdine Arbi; Tan, Chin Ping; Al-Resayes, Saud Ibrahim

    2014-01-01

    Highlights: • Transesterification reaction with methanol in the presence of NaOH as a catalyst. • Optimization of key reaction parameters were performed. • Some fuel properties of biodiesel were measured and compared with biodiesel standards. • Ten of the properties that were evaluated for the diesel conform to the ASTM and EN standards values. - Abstract: Recently, biodiesel has been gaining market share against fossil-origin diesel due to its ecological benefits and because it can be directly substituted for traditional diesel oils. However, the high cost of the raw materials required to produce biodiesel make it more expensive than fossil diesel. Therefore, low-priced raw materials, such as waste cooking oil and animal fats, are of interest because they can be used to drive down the cost of biodiesel. We have produced biodiesel from camel fat using a transesterification reaction with methanol in the presence of NaOH. The experimental variables investigated in this study were the temperature (30–75 °C), reaction time (20–160 min), catalyst concentration (0.25–1.5%), and methanol/fat molar ratio (4:1–9:1). A maximum biodiesel yield of 98.6% was obtained. The fuel properties of biodiesel, such as iodine value, saponification value, density, kinematic viscosity, cetane number, flash point, sulfur content, carbon residue, water and sediment, high heating value, refractive index, cloud point, pour point, and distillation characteristics, were measured. The properties were compared with EN 14214 and ASTM 6751 biodiesel standards, and an acceptable level of agreement was obtained

  18. Crude glycerol from biodiesel industry as substrate for biosurfactant production by Bacillus subtilis ATCC 6633

    Directory of Open Access Journals (Sweden)

    Marylane de Sousa

    2014-04-01

    Full Text Available Glycerol, a co-product of the biodiesel industry, may be a suitable raw material for the production of high added-value compounds by the microorganisms. This study aimed to use the glycerol obtained from the biodiesel production process as the main carbon source for biosurfactant production by Bacillus subtilis ATCC 6633. Results indicated that the strain lowered the surface tension of the cell-free fermented broth to 31.5 ± 1.6 mN/m, indicating the production of biosurfactant. The critical micelle concentration (CMC = 33.6 mN/m obtained was similar to the previously reported for biossurfactants isolated from other Bacillus. The produced biosurfactant was able to emulsify n-hexadecane and soybean oil.

  19. Trends of non-destructive analytical methods for identification of biodiesel feedstock in diesel-biodiesel blend according to European Commission Directive 2012/0288/EC and detecting diesel-biodiesel blend adulteration: A brief review.

    Science.gov (United States)

    Mazivila, Sarmento Júnior

    2018-04-01

    Discrimination of biodiesel feedstock present in diesel-biodiesel blend is challenging due to the great similarity in the spectral profile as well as digital image profile of each type of feedstock employed in biodiesel production. Once the marketed diesel-biodiesel blend is subsidized, in which motivates adulteration in biofuel blend by cheaper supplies with high solubility to obtain profits associated with the subsidies involved in biodiesel production. Non-destructive analytical methods based on qualitative and quantitative analysis for detecting marketed diesel-biodiesel blend adulteration are reviewed. Therefore, at the end is discussed the advantage of the qualitative analysis over quantitative analysis, when the systems require immediate decisions such as to know if the marketed diesel-biodiesel blend is unadulterated or adulterated in order to aid the analyst in selecting the most appropriate green analytical procedure for detecting diesel-biodiesel blend adulteration proceeding in fast way. This critical review provides a brief review on the non-destructive analytical methods reported in scientific literature based on different first-order multivariate calibration models coupled with spectroscopy data and digital image data to identify the type of biodiesel feedstock present in diesel-biodiesel blend in order to meets the strategies adopted by European Commission Directive 2012/0288/EC as well as to monitoring diesel-biodiesel adulteration. According to that Directive, from 2020 biodiesel produced from first-generation feedstock, that is, oils employed in human food such as sunflower, soybean, rapeseed, palm oil, among other oils should not be subsidized. Therefore, those non-destructive analytical methods here reviewed are helpful for discrimination of biodiesel feedstock present in diesel-biodiesel blend according to European Commission Directive 2012/0288/EC as well as for detecting diesel-biodiesel blend adulteration. Copyright © 2017 Elsevier B

  20. Beef tallow biodiesel produced in a pilot scale

    Energy Technology Data Exchange (ETDEWEB)

    da Cunha, Michele Espinosa; Krause, Laiza Canielas; Moraes, Maria Silvana Aranda; Faccini, Candice Schmitt; Almeida, Suelen Rodrigues; Caramao, Elina Bastos [Chemistry Institute/Federal University of Rio Grande do Sul/UFRGS - Av. Bento Goncalves, 9500, 91501-970, Porto Alegre, RS (Brazil); Jacques, Rosangela Assis [Federal University of Pelotas/Federal University of Pampa (UFPel/UNIPAMPA-Bage) (Brazil); Rodrigues, Maria Regina Alves [Department of Organic Chemistry (DQO), Chemistry Institute (IQ), Federal University of Pelotas (UFPel), Campus Universitario, s/n - Caixa Postal 354, 96010-900, Pelotas/RS (Brazil)

    2009-04-15

    In the present work, the process of biodiesel production in a pilot plant has been studied using beef tallow as raw materials with methanol and potassium hydroxide as catalyst. The biodiesel quality is regulated by Brazilian specifications (Resolution 42) by the National Agency of Petroleum (ANP). The alkaline transesterification of animal fat with methanol produces a biodiesel with high quality and also with a good conversion rate. The process is possible but the economical viability must be improved by recovering methanol and glycerin. The obtained results have been used for industrial scale up of the process. (author)

  1. Speed of sound in biodiesel produced by low power ultrasound

    Science.gov (United States)

    Oliveira, P. A.; Silva, R. M. B.; Morais, G. C.; Alvarenga, A. V.; Costa-Felix, R. P. B.

    2018-03-01

    The quality control of the biodiesel produced is an important issue to be addressed for every manufacturer or retailer. The speed of sound is a property that has an influence on the quality of the produced fuel. This work presents the evaluation about the speed of sound in biodiesel produced with the aid of low power ultrasound in the frequencies of 1 MHz and 3 MHz. The speed of sound was measured by pulse-echo technique. The ultrasonic frequency used during reaction affects the speed of sound in biodiesel. The larger expanded uncertainty for adjusted curve was 4.9 m.s-1.

  2. Superstructure optimization of biodiesel production from microalgal biomass

    DEFF Research Database (Denmark)

    Rizwan, Muhammad; Lee, Jay H.; Gani, Rafiqul

    2013-01-01

    In this study, we propose a mixed integer nonlinear programming (MINLP) model for superstructure based optimization of biodiesel production from microalgal biomass. The proposed superstructure includes a number of major processing steps for the production of biodiesel from microalgal biomass...... for the production of biodiesel from microalgae. The proposed methodology is tested by implementing on a specific case study. The MINLP model is implemented and solved in GAMS using a database built in Excel. The results from the optimization are analyzed and their significances are discussed....

  3. Modelling and operation of reactors for enzymatic biodiesel production

    DEFF Research Database (Denmark)

    Price, Jason Anthony

    to the production of high fructose corn syrup, upgrading of fats and oils and biodiesel production to name a few. Despite these examples of industrial enzymatic applications, it is still not “clear cut” how to implement biocatalyst in industry and how best to optimize the processes. This is because the processing...... aspects of the enzyme with reaction/reactor engineering is performed. This strategy is applied to a case study of biodiesel production catalysed by a liquid enzyme formulation. The use of enzymes for biodiesel production is still in its infancy with non-optimized process designs. Furthermore is it unclear...

  4. Biodiesel Production from Bombacopsis glabra Oil by Methyl Transesterification Method

    Directory of Open Access Journals (Sweden)

    Francisca Diana da Silva Araújo

    2017-09-01

    Full Text Available The objective of this work was to produce methyl biodiesel from Bombacopis glabra (B. glabra oil degummed with H3PO4. The methyl biodiesel was prepared in an alkaline medium, and characterized by physico-chemical parameters, thin-layer chrmatograghy (TLC, gas chromatograph (GC, (Nuclear magnetic resonance of hydrogen (H-NMR, thermogravimetry and infrared analysis. The physico-chemical parameters of biodiesel were in accordance with the limits established by National Agency of Petroleum, Natural Gas and Biofuels (ANP Resolution 45/2014, except oxidation stability, where it was corrected with the addition of antioxidants such as TBHQ and BHT.

  5. Impact of Biodiesel Fuels on Air Quality and Human Health: Task 1 Report; Incorporate Biodiesel Data into Vehicle Emissions Databases for Modeling

    Energy Technology Data Exchange (ETDEWEB)

    Lindhjem, C.; Pollack, A.

    2003-05-01

    This document is the Task 1 report for the NREL"Impact of Biodiesel Fuels on Air Quality and Human Health" study. This report provides a discussion and analysis of the available biodiesel test data, and makes recommendations for how biodiesel effects on pollutant mass emissions as well as chemical composition should be incorporated into emission inventories for use in air quality modeling.

  6. Impact of Biodiesel Fuels on Air Quality and Human Health: Task 2 Report; The Impact of Biodiesel Fuels on Ozone Concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Morris, R. E.; Mansell, G. E.; Jia, Y.; Wilson, G.

    2003-05-01

    This report documents Task 2 of the NREL study"Impact of Biodiesel Fuels on Air Quality and Hyman Health". Under Task 1, engine test data using biodiesel and standard diesel fuels were analyzed to estimate the effects biodiesel fuel has on heavy duty diesel vehicle tailpipe emissions.

  7. First bio-diesel plant from oil-producing in Brazil; Premiere usine de biodiesel a partir d'oleagineux au Bresil

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-03-15

    In march 2005, Brazil implemented its first bio-diesel production plant from vegetal oils. This unit, situated in the Minas Gerais state will produce 12 millions of liter of bio-diesel per year. Cars using bio-diesel fuels generate 16% less of gases and fumes than petrol fuel cars, for the same fuel consumption. (A.L.B.)

  8. Biomass for biodiesel production on family farms in Brazil: promise or failure? : integrated assessment of biodiesel crops, farms, policies and producer organisations

    NARCIS (Netherlands)

    Belo Leite, Dal J.G.

    2013-01-01

    In Brazil, a biodiesel policy was implemented as a way of reducing poverty among family farms. The objective of this thesis is to perform an integrated assessment of biodiesel crops, farm types, biodiesel policies and producer organisations that reveals opportunities and limitations of family

  9. Calorific value for compositions with biodiesel of fat chicken and diesel oil; Valor calorifico para composicoes com biodiesel da gordura de frango e oleo diesel

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Marcelo Jose da [Universidade de Campinas (FEAGRI/UNICAMP), SP (Brazil). Fac. de Engenharia Agricola], email: marcelo.jose@feagri.unicamp.br; Souza, Samuel N.M. de; Souza, Abel A. de; Martins, Gislaine I. [Universidade Estadual do Oeste do Parana (CCET/UNIOESTE), Cascavel, PR (Brazil). Centro de Ciencias Exatas e Tecnologicas], emails: ssouza@unioeste.br, abel.sza@hotmail.com, iastiaque@yahoo.com.br

    2011-07-01

    The biodiesel fuel is a renewable source of alternative fuel used in diesel cycle engines. The production of biodiesel involves the reaction of methanol with fatty acids of animal or vegetable. The production of biodiesel from chicken fat can be very attractive for some regions from Brazil with high poultry production, as in the Parana West and Santa Catarina West. In this study , the goal was the lower calorific value of the compositions between biodiesel and diesel oil: 100% Diesel oil (B0), 20% biodiesel (B20), 40% biodiesel (B40), 60% biodiesel (B60), 80% biodiesel (B80 ), 100% biodiesel (B100). The biodiesel used was acquired in the Centre for Development and Diffusion of technologies on the Assis Gurgacz College, in Cascavel city. The nominal production capacity of the unit is 900 liters on period of 8 hours. The model of the calorimeter used, was the E2K. The lower calorific value of B100 composition was 35.388 MJ kg-1 and the diesel oil was 41.299 MJ kg-1. With the measuring of the caloric value of six samples mix of diesel oil and biodiesel, was obtained a linear function decrease of the calorific value when increased it the proportion of biodiesel from chicken fat into fuel. (author)

  10. Biodiesel production through transesterification over natural calciums

    Energy Technology Data Exchange (ETDEWEB)

    Ngamcharussrivichai, Chawalit [Fuels Research Center, Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Phyathai Rd., Patumwan, Bangkok 10330 (Thailand); Center of Excellence for Petroleum, Petrochemicals and Advanced Materials, Chulalongkorn University, Phyathai Rd., Patumwan, Bangkok 10330 (Thailand); Nunthasanti, Pramwit; Tanachai, Sithikorn; Bunyakiat, Kunchana [Fuels Research Center, Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Phyathai Rd., Patumwan, Bangkok 10330 (Thailand)

    2010-11-15

    Transesterification of palm kernel oil (PKO) with methanol over various natural calciums, including limestone calcite, cuttlebone, dolomite, hydroxyapatite, and dicalcium phosphate, has been investigated at 60 C and 1 atm. The study showed that dolomite, mainly consisting of CaCO{sub 3} and MgCO{sub 3}, is the most active catalyst. The calcination temperature largely affected the physicochemical properties, as evidenced by N{sub 2} adsorption-desorption measurement, TGA, SEM and XRD, and the transesterification performance of the resultant catalysts. It was found that the calcination of dolomite at 800 C resulted in a highly active mixed oxide. CaO was suggested to be the catalytically active site responsible for the methyl ester formation. Under the suitable reaction conditions, the amount of dolomite calcined at 800 C = 6 wt.% based on the weight of oil, the methanol/oil molar ratio = 30, and the reaction time = 3 h, the methyl ester content of 98.0% can be achieved. The calcined dolomite can be reused many times. The analyses of some important fuel properties indicated that the biodiesel produced had the properties that meet the standard of biodiesel and diesel fuel issued by the Department of Energy Business, Ministry of Energy, Thailand. (author)

  11. Biodiesel production using waste frying oil

    International Nuclear Information System (INIS)

    Charpe, Trupti W.; Rathod, Virendra K.

    2011-01-01

    Research highlights: → Waste sunflower frying oil is successfully converted to biodiesel using lipase as catalyst. → Various process parameters that affects the conversion of transesterification reaction such as temperature, enzyme concentration, methanol: oil ratio and solvent are optimized. → Inhibitory effect of methanol on lipase is reduced by adding methanol in three stages. → Polar solvents like n-hexane and n-heptane increases the conversion of tranesterification reaction. - Abstract: Waste sunflower frying oil is used in biodiesel production by transesterification using an enzyme as a catalyst in a batch reactor. Various microbial lipases have been used in transesterification reaction to select an optimum lipase. The effects of various parameters such as temperature, methanol:oil ratio, enzyme concentration and solvent on the conversion of methyl ester have been studied. The Pseudomonas fluorescens enzyme yielded the highest conversion. Using the P. fluorescens enzyme, the optimum conditions included a temperature of 45 deg. C, an enzyme concentration of 5% and a methanol:oil molar ratio 3:1. To avoid an inhibitory effect, the addition of methanol was performed in three stages. The conversion obtained after 24 h of reaction increased from 55.8% to 63.84% because of the stage-wise addition of methanol. The addition of a non-polar solvent result in a higher conversion compared to polar solvents. Transesterification of waste sunflower frying oil under the optimum conditions and single-stage methanol addition was compared to the refined sunflower oil.

  12. Biodiesel production plant project from fritter oil

    International Nuclear Information System (INIS)

    Cordoví Felipe, Carlos Miguel; Gandón Hernández, José; Sarracent López, Anabel; García Díaz, Marilín

    2017-01-01

    Increments in commercialization values of fossil fuels as well as the ecological impact in the environment, motivated the study about methods to obtain clean (alternative) energies that don't produce emanations or, in the worst of cases reduce them as much as possible. In this work is shown the project of a plant of a biodiesel production plant, using as raw material fritter oils coming from foods processing facilities and/or from tourist facilities. The production technology is based on studies, carried out by the foods research group in Chemical Engineering Faculty, Technological University of Havana in biodiesel production through the mechanism of alkaline transesterificationón with homogeneous catalysts. The plant was designed in modular type in order to facilitate any production amplification that is required and has all the necessary elements for its assembly, it is easy to repair in situ according to resources possibilities and of simple operation so that it is possible for not qualified workers in technical questions. The production capacity in this project is 300 liters of raw material per batch, coming from a fritter foods facility. (author)

  13. Solar Water Heating System for Biodiesel Production

    Science.gov (United States)

    Syaifurrahman; Usman, A. Gani; Rinjani, Rakasiwi

    2018-02-01

    Nowadays, electricity become very expensive thing in some remote areas. Energy from solar panels give the solution as renewable energy that is environment friendly. West Borneo is located on the equator where the sun shines for almost 10-15 hours/day. Solar water heating system which is includes storage tank and solar collections becomes a cost-effective way to generate the energy. Solar panel heat water is delivered to water in storage tank. Hot water is used as hot fluid in biodiesel jacked reactor. The purposes of this research are to design Solar Water Heating System for Biodiesel Production and measure the rate of heat-transfer water in storage tank. This test has done for 6 days, every day from 8.30 am until 2.30 pm. Storage tank and collection are made from stainless steel and polystyrene a well-insulated. The results show that the heater can be reach at 50ºC for ±2.5 hours and the maximum temperature is 62ºC where the average of light intensity is 1280 lux.

  14. Performance characteristics of rubber seed oil biodiesel

    Science.gov (United States)

    Liu, P.; Qin, M.; Wu, J.; Chen, B. S.

    2018-01-01

    The lubricity, ignition quality, oxidative stability, low temperature flow property and elastomeric compatibility of rubber seed oil biodiesel(RSM) were evaluated and compared with conventional petro-diesel. The results indicated that RSM and its blends with petro-diesel possessed outstanding lubricity manifested by sharp decrease in wear scar diameters in the high-frequency reciprocating rig(HFRR) testing. They also provided acceptable flammability and cold flow property,although the cetane numbers (CN) and cold filter plugging points(CFPP) of biodiesel blends slightly decreased with increasing contents of petro-diesel. However, RSM proved to be very susceptible to oxidation at elevated temperatures during prolonged oxidation durations, characterized by increased peroxide values, viscosity, acid values and isooctane insolubles. The oxidation stability of RSM could be significantly improved by antioxidants such as BD100, a phenol antioxidant produced by Ciba corporation. Furthermore, RSM provided poor compatibility with some elastomeric rubbers such as polyacrylate, nitrile-butadiene and chloroprene, but was well compatible with the hydrogenated nitrile-butadiene elastomer.

  15. Equilibrium study for ternary mixtures of biodiesel

    Science.gov (United States)

    Doungsri, S.; Sookkumnerd, T.; Wongkoblap, A.; Nuchitprasittichai, A.

    2017-11-01

    The liquid-liquid equilibrium (LLE) data for the ternary mixtures of methanol + fatty acid methyl ester (FAME) + palm oil and FAME + palm oil + glycerol at various temperatures from 35 to 55°C, the tie lines and binodial curves were also investigated and plotted in the equilibrium curve. The experimental results showed that the binodial curves of methanol + FAME + palm oil depended significantly with temperature while the binodial curves of FAME + palm oil + glycerol illustrated insignificant change with temperatures. The interaction parameters between liquid pair obtained for NRTL (Nonrandom Two-Liquid) and UNIQUAC (Universal Quasi-Chemical Theory) models from the experimental data were also investigated. It was found that the correlated parameters of UNIQUAC model for system of FAME + palm oil + glycerol, denoted as a13 and a31, were 580.42K and -123.69K, respectively, while those for system of methanol + FAME + palm oil, denoted as a42 and a24, were 71.48 K and 965.57K, respectively. The ternary LLE data reported here would be beneficial for engineers and scientists to use for prediction of yield and purity of biodiesel for the production. The UNIQUAC model agreed well with the experimental data of ternary mixtures of biodiesel.

  16. Vanadyl phosphate catalysts in biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    Di Serio, M.; Cozzolino, M.; Tesser, R.; Santacesaria, E. [Universita degli studi di Napoli ' Federico II' , Dipartimento di Chimica, via Cintia 4, I-80126 Napoli (Italy); Patrono, P.; Pinzari, F. [CNR-IMIP Area della Ricerca di Roma, via Salaria, 00016 Monterotondo Scalo, Roma (Italy); Bonelli, B. [Politecnico di Torino, Dipartimento di Scienza dei Materiali ed Ingegneria Chimica, C.so Duca degli Abruzzi 24, I-10129 Torino (Italy)

    2007-03-22

    The possibility of using vanadyl phosphate (VOP)-based catalysts in biodiesel production has been investigated. Vanadium phosphate catalysts resulted very active in the transesterification reaction of triglycerides with methanol, despite their low specific surface area. A slow deactivation of the catalysts has been experimentally detected under the reaction conditions, but the catalyst can easily be regenerated by calcination in air. The influence of the calcination treatment on the surface structure and, consequently, on its catalytic performances was deeply investigated. Both fresh and used catalysts were characterized by using several techniques, such as BET, X-ray diffraction (XRD), UV-vis diffuse reflectance (DRUV) and laser-Raman (LRS). The characterization results showed that the deactivation is due to a progressive reduction of vanadium (V) species from V{sup 5+} to V{sup 4+} and V{sup 3+} by methanol. By comparing the obtained performances of VOP catalysts with the ones of other heterogeneous catalysts reported by the literature, it is possible to conclude that VOP catalysts can already be used industrially for biodiesel production but their performances can probably be greatly improved in perspective. (author)

  17. Treatment of Biodiesel Wastewater by Electrocoagulation Process

    Directory of Open Access Journals (Sweden)

    Anchalee Srirangsan

    2009-07-01

    Full Text Available The objective of this research was to determine the optimum conditions for biodiesel wastewater treatment using an electrocoagulation process. Wastewater samples were obtained from a small-scale, commercial biodiesel production plant that employs an alkali-catalyzed tranesterification process. The wastewater was characterized by the high contents of alkali and high oil content of 6,020 mg/L. Tested operational conditions included types of electrode, current density, retention time and initial pH. The tested electrode materials for electrocoagulation were aluminum (Al, iron (Fe and graphite (C. Five tested pairs of anode and cathode materials included Fe-Fe, Fe-C, Al-Al, Al-C, C-C. Results show that the optimum conditions were achieved by using the electrodes of Al-C, applying the current density of 8.32 mA/cm2 to the wastewater with an initial pH value of 6 for 25 min. The removal efficiency was found to be 97.8 % for grease & oil (G&O, 96.9 % for SS and 55.4 % for COD. Moreover, the small amount of produced sludge was readily to remove from the treated wastewater.

  18. Genomic Prospecting for Microbial Biodiesel Production

    Energy Technology Data Exchange (ETDEWEB)

    Lykidis, Athanasios; Lykidis, Athanasios; Ivanova, Natalia

    2008-03-20

    Biodiesel is defined as fatty acid mono-alkylesters and is produced from triacylglycerols. In the current article we provide an overview of the structure, diversity and regulation of the metabolic pathways leading to intracellular fatty acid and triacylglycerol accumulation in three types of organisms (bacteria, algae and fungi) of potential biotechnological interest and discuss possible intervention points to increase the cellular lipid content. The key steps that regulate carbon allocation and distribution in lipids include the formation of malonyl-CoA, the synthesis of fatty acids and their attachment onto the glycerol backbone, and the formation of triacylglycerols. The lipid biosynthetic genes and pathways are largely known for select model organisms. Comparative genomics allows the examination of these pathways in organisms of biotechnological interest and reveals the evolution of divergent and yet uncharacterized regulatory mechanisms. Utilization of microbial systems for triacylglycerol and fatty acid production is in its infancy; however, genomic information and technologies combined with synthetic biology concepts provide the opportunity to further exploit microbes for the competitive production of biodiesel.

  19. BACTERIAL COMMUNITY DYNAMICS AND ECOTOXICOLOGICAL ASSESSMENT DURING BIOREMEDIATION OF SOILS CONTAMINATED BY BIODIESEL AND DIESEL/BIODIESEL BLENDS.

    Science.gov (United States)

    Matos, G I; Junior, C S; Oliva, T C; Subtil, D F; Matsushita, L Y; Chaves, A L; Lutterbach, M T; Sérvulo, E F; Agathos, S N; Stenuit, B

    2015-01-01

    The gradual introduction of biodiesel in the Brazilian energy landscape has primarily occurred through its blending with conventional petroleum diesel (e.g., B20 (20% biodiesel) and B5 (5% biodiesel) formulations). Because B20 and lower-level blends generally do not require engine modifications, their use as transportation fuel is increasing in the Brazilian distribution networks. However, the environmental fate of low-level biodiesel blends and pure biodiesel (B100) is poorly understood and the ecotoxicological-safety endpoints of biodiesel-contaminated environments are unknown. Using laboratory microcosms consisting of closed reactor columns filled with clay loam soil contaminated with pure biodiesel (EXPB100) and a low-level blend (EXPB5) (10% w/v), this study presents soil ecotoxicity assessement and dynamics of culturable heterotrophic bacteria. Most-probable-number (MPN) procedures for enumeration of bacteria, dehydrogenase assays and soil ecotoxicological tests using Eisenia fetida have been performed at different column depths over the course of incubation. After 60 days of incubation, the ecotoxicity of EXPB100-derived samples showed a decrease from 63% of mortality to 0% while EXPB5-derived samples exhibited a reduction from 100% to 53% and 90% on the top and at the bottom of the reactor column, respectively. The dehydrogenase activity of samples from EXPB100 and EXPB5 increased significantly compared to pristine soil after 60 days of incubation. Growth of aerobic bacterial biomass was only observed on the top of the reactor column while the anaerobic bacteria exhibited significant growth at different column depths in EXPB100 and EXPB5. These preliminary results suggest the involvement of soil indigenous microbiota in the biodegradation of biodiesel and blends. However, GC-FID analyses for quantification of fatty acid methyl esters (FAMEs) and aliphatic hydrocarbons and targeted sequencing of 16S rRNA tags using illumina platforms will provide important

  20. Biodiesel Reactor Design with Glycerol Separation to Increase Biodiesel Production Yield

    OpenAIRE

    Budy Rahmat; Imas Siti Setiasih; Roni Kastaman

    2013-01-01

    The study consisted of reactor design used for transesterification process, effect of glycerol separation ontransesterification reaction, determination of biodiesel quality, and mass balance analysis. The reactor was designed byintegrating circulated pump/stirrer, static mixer, and sprayer that intensify the reaction in the outer tank reactor. The objective was to reduce the use of methanol in excess and to shorten the processing time. The results showed that thereactor that applied the glyce...

  1. Les biocarburants en Argentine : facteurs et enjeux de la production de biodiesel de soja

    Directory of Open Access Journals (Sweden)

    Guibert Martine

    2012-05-01

    Full Text Available In 2006, Argentina has sanctioned a national law to regulate biofuel production and consumption. Since 2007, soybean actors started producing biodiesel for international market -especially to Europe- and the country quickly became the major biodiesel exporter. In 2010, around twenty processing units started supplying the domestic market. Diesel sold in Argentina contained 5% of biodiesel. The obligation to add 5% of biodiesel to diesel has passed to 7% and the goal is to increase this percentage. The State support and soybean biodiesel competitiveness have been important for biodiesel chain development but some doubts could appear about the kind of actors that could have the benefits.

  2. Rheological behavior of oil and biodiesel from Moringa oleifera

    International Nuclear Information System (INIS)

    Díaz Domínguez, Yosvany; Tabio García, Danger; Rondón Macías, Maylin; Fernández Santana, Elina; Rodríguez Muñoz, Susana; Piloto‐Rodríguez, Ramón

    2017-01-01

    The seeds of Moringa oleifera contain between 30 and 45% of oil, which has motivated the development of investigations with a view to their possible use. The present work aims to determine the rheological behavior of Moringa oleifera oil and biodiesel. The synthesis of biodiesel from crude Moringa oleifera oil was made using methanol with presence of sodium hydroxide. The average yield of this stage was 93%. The results of the rheological study shown that the viscosity at 40°C of Moringa oleifera oil is independent of the shear rate, which corresponds to the behavior of a Newtonian fluid. However, for biodiesel it was demonstrated that there is a dependence of the viscosity with the shear rate (non-Newtonian fluid). This result is corroborated by the fluidity curve, assuring that Moringa oleifera biodiesel behaves as a dilating fluid. (author)

  3. Sustainable and Intensified Design of a Biodiesel Production Process

    DEFF Research Database (Denmark)

    Mansouri, Seyed Soheil; Ismail, Muhammad I.; Babi, Deenesh Kavi

    impact and maximum profitability is needed. In this work a computer-aided framework for process synthesis and process intensification is applied for sustainable production of biodiesel from pure/waste palm oil as the feedstock. This approach examines several biodiesel processing routes that were...... collected through available data and current technologies reported in the literature. Using this information, a generic superstructure of processing routes was created that described a network of configurations representing multiple designs for the production of biodiesel. Therefore, based on the currently...... of economic and environmental sustainability was identified. For the case of biodiesel production, the intensified process alternative turned out to be the most economical and more sustainable than other alternatives. The computer-aided methods and tools used in this work are: SustainPro (method and tool...

  4. Biodiesel From Alternative Oilseed Feedstocks: Production and Properties

    Science.gov (United States)

    Fatty acid methyl esters were prepared and evaluated as potential biodiesel fuels from several alternative oilseed feedstocks, which included camelina (Camelina sativa L.), coriander (Coriandrum sativum L.), field mustard (Brassica juncea L.), field pennycress (Thlaspi arvense L.), and meadowfoam (L...

  5. Biodiesel production from castor oil in Brazil: A difficult reality

    International Nuclear Information System (INIS)

    Silva Cesar, Aldara da; Otavio Batalha, Mario

    2010-01-01

    The Brazilian National Program for Production and Use of Biodiesel (PNPB in Portuguese) has created a huge demand for biodiesel in Brazil. The PNPB is strongly based on social development through the inclusion of family farmers in projects integrated with biodiesel power plants. Among the various oilseeds, castor bean (Ricinus communis L.) was identified as the ideal one to promote social development in the semi-arid region. However, although promising, the mechanisms of the federal program are still insufficient to promote the effective participation of family farmers. This research shows that companies are facing huge problems in implementing contracts with family farmers. It describes and analyzes the functioning dynamics of this agro-production chain. This paper addresses the identification and the discussion of these obstacles, in order to increase the competitiveness of the biodiesel agribusiness chain, based on castor oil social projects in Brazil.

  6. Biodiesel production from castor oil in Brazil. A difficult reality

    Energy Technology Data Exchange (ETDEWEB)

    Silva Cesar, Aldara da; Otavio Batalha, Mario [Federal University of Sao Carlos, Gepai - Grupo de Estudos e Pesquisas Agroindustriais, Departamento de Engenharia de Producao - UFSCar, Rodovia Washington Luis, km 235 - CEP 13565-905 - Sao Carlos (Brazil)

    2010-08-15

    The Brazilian National Program for Production and Use of Biodiesel (PNPB in Portuguese) has created a huge demand for biodiesel in Brazil. The PNPB is strongly based on social development through the inclusion of family farmers in projects integrated with biodiesel power plants. Among the various oilseeds, castor bean (Ricinus communis L.) was identified as the ideal one to promote social development in the semi-arid region. However, although promising, the mechanisms of the federal program are still insufficient to promote the effective participation of family farmers. This research shows that companies are facing huge problems in implementing contracts with family farmers. It describes and analyzes the functioning dynamics of this agro-production chain. This paper addresses the identification and the discussion of these obstacles, in order to increase the competitiveness of the biodiesel agribusiness chain, based on castor oil social projects in Brazil. (author)

  7. Biodiesel production from castor oil in Brazil: A difficult reality

    Energy Technology Data Exchange (ETDEWEB)

    Silva Cesar, Aldara da, E-mail: aldara@dep.ufscar.b [Federal University of Sao Carlos, Gepai - Grupo de Estudos e Pesquisas Agroindustriais, Departamento de Engenharia de Producao - UFSCar, Rodovia Washington Luis, km 235 - CEP 13565-905 - Sao Carlos - SP (Brazil); Otavio Batalha, Mario [Federal University of Sao Carlos, Gepai - Grupo de Estudos e Pesquisas Agroindustriais, Departamento de Engenharia de Producao - UFSCar, Rodovia Washington Luis, km 235 - CEP 13565-905 - Sao Carlos - SP (Brazil)

    2010-08-15

    The Brazilian National Program for Production and Use of Biodiesel (PNPB in Portuguese) has created a huge demand for biodiesel in Brazil. The PNPB is strongly based on social development through the inclusion of family farmers in projects integrated with biodiesel power plants. Among the various oilseeds, castor bean (Ricinus communis L.) was identified as the ideal one to promote social development in the semi-arid region. However, although promising, the mechanisms of the federal program are still insufficient to promote the effective participation of family farmers. This research shows that companies are facing huge problems in implementing contracts with family farmers. It describes and analyzes the functioning dynamics of this agro-production chain. This paper addresses the identification and the discussion of these obstacles, in order to increase the competitiveness of the biodiesel agribusiness chain, based on castor oil social projects in Brazil.

  8. Microreactors - a marvel of modern manufacturing technology: biodiesel case study

    CSIR Research Space (South Africa)

    Buddoo, SR

    2008-11-01

    Full Text Available Microreactors are miniature reactors for carrying out chemical reactions. CSIR Biosciences has been investigating the production of biodiesel using various sources of vegetable oils, for example, soya, sunflower, canada, Jatropha, palm and peanuts...

  9. rights reserved Assessment of Indigenous Bacteria from Biodiesel ...

    African Journals Online (AJOL)

    ADOWIE PERE

    doi.org/10.4314/jasem.v22i2.12 ... Keywords: Biodiesel, bioremediation, bacteria, effluent, hydrocarbon. Indigenous soil Microorganisms are tiny colonies of .... refinery waste-contaminated site and an aviation gasoline contaminated site.

  10. Biodiesel in Belgium. From rapeseed oil to used vegetable oils

    International Nuclear Information System (INIS)

    Pelkmans, L.

    1997-01-01

    There are two motives for the search for alternative motor fuels: reducing the growing pressure of traffic on environment, and looking for a replacement for petrol and diesel oil that are bound to be worn-out in a few decades. A promising alternative motor fuel is biodiesel. The author's institute is involved in its second biodiesel demonstration project. In the first project RME (rapeseed methyl ester) was used undiluted in five passenger cars for two years. There were no technical problems and a clear environmental advantage was noticed. However, the price remains a problem. The use of waste vegetable oils for the production of biodiesel could help to overcome this problem. Therefore, a second biodiesel demonstration project was started in which UVOME (used vegetable oil methyl ester) is used. The preliminary results show a great similarity with the RME results and no technical problems in real life use. 1 fig., 1 tab., 5 refs

  11. Production of biodiesel using lipase encapsulated in κ-carrageenan

    CERN Document Server

    Ravindra, Pogaku

    2015-01-01

    This book explores a novel technique for processing biodiesel using lipase immobilization by encapsulation and its physical properties, stability characteristics, and application in stirred tank and re-circulated packed bed immobilized reactors for biodiesel production. The enzymatic processing of biodiesel addresses many of the problems associated with chemical processing. It requires only moderate operating conditions and yields a high-quality product with a high level of conversion and the life cycle assessment of enzymatic biodiesel production has more favourable environmental consequences. The chemical processing problems of waste water treatment are lessened and soap formation is not an issue, meaning that waste oil with higher FFA can be used as the feedstock. The by product glycerol does not require any purification and it can be sold at higher price. However, soluble enzymatic processing is not perfect. It is costly, the enzyme cannot be recycled and its removal from the product is difficult. For...

  12. Analysis of national Jatropha biodiesel programme in Senegal

    DEFF Research Database (Denmark)

    Dafrallah, Touria; Ackom, Emmanuel

    2016-01-01

    and other biodiesel crop options, based on findings from an agro-environmental mapping exercise have been shown. Findings show that prior policies in agricultural and energy sectors had been instrumental in developing the NJP. It highlights significant challenges in the value chain, the implementation...... of NJP and on the importance of using empirical assessment of evidence to inform on the biodiesel crop type compared to a focus on only one crop, Jatropha. Agro-environmental mapping was identified as useful technique prior to biodiesel cultivation. The work reported here indicates Jatropha having...... on the suitability of areas for Jatropha cultivation and on environmentally, socially and culturally sensitive areas. Policy options have been suggested for environmentally benigned sustained biodiesel activities in Senegal....

  13. Room temperature synthesis of biodiesel using sulfonated graphitic carbon nitride

    OpenAIRE

    Baig, R. B. Nasir; Verma, Sanny; Nadagouda, Mallikarjuna N.; Varma, Rajender S.

    2016-01-01

    Sulfonation of graphitic carbon nitride (g-CN) affords a polar and strongly acidic catalyst, Sg-CN, which displays unprecedented reactivity and selectivity in biodiesel synthesis and esterification reactions at room temperature.

  14. Room temperature synthesis of biodiesel using sulfonated graphitic carbon nitride

    Science.gov (United States)

    Sulfonation of graphitic carbon nitride (g-CN) affords a polar and strongly acidic catalyst, Sg-CN, which displays unprecedented reactivity and selectivity in biodiesel synthesis and esterification reactions at room temperature.

  15. Biodiesel Production from Rubber Seed Oil via Esterification Process

    Directory of Open Access Journals (Sweden)

    W Widayat

    2012-07-01

    Full Text Available One promise source of alternative energy is biodiesel from rubber seed oil, because the raw materials available in plentiful quantities and can be renewed. In addition, the rubber seed is still lack of utilization, and Indonesia is one of the largest rubbers producing country in the world. The objective of this research is to studied on biodiesel production by esterification process. Parameters used in this study are the ratio of catalyst and temperature and its influence on the characteristics of the resulting biodiesel product. Characterization of rubber seed include acid content number analysis, saponification numbers, density, viscosity, iodine number, type of free fatty acids and triglyceride oils. The results of analysis showed that rubber seed oil content obtained is 50.5%. The results of the GCMS analysis showed that a free fatty acid level in rubber seed is very high. Conversion into bio-diesel oil is obtained by at most 59.91% and lowest 48.24%.

  16. Glycerol extracting dealcoholization for the biodiesel separation process.

    Science.gov (United States)

    Ye, Jianchu; Sha, Yong; Zhang, Yun; Yuan, Yunlong; Wu, Housheng

    2011-04-01

    By means of utilizing sunflower oil and Jatropha oil as raw oil respectively, the biodiesel transesterification production and the multi-stage extracting separation were carried out experimentally. Results indicate that dealcoholized crude glycerol can be utilized as the extracting agent to achieve effective separation of methanol from the methyl ester phase, and the glycerol content in the dealcoholized methyl esters is as low as 0.02 wt.%. For the biodiesel separation process utilizing glycerol extracting dealcoholization, its technical and equipment information were acquired through the rigorous process simulation in contrast to the traditional biodiesel distillation separation process, and results show that its energy consumption decrease about 35% in contrast to that of the distillation separation process. The glycerol extracting dealcoholization has sufficient feasibility and superiority for the biodiesel separation process. Copyright © 2011 Elsevier Ltd. All rights reserved.

  17. Upstream and downstream strategies to economize biodiesel production.

    Science.gov (United States)

    Hasheminejad, Meisam; Tabatabaei, Meisam; Mansourpanah, Yaghoub; Khatami far, Mahdi; Javani, Azita

    2011-01-01

    In recent years biodiesel has drawn considerable amount of attention as a clean and renewable fuel. Biodiesel is produced from renewable sources such as vegetable oils and animal fat mainly through catalytic or non-catalytic transesterification method as well as supercritical method. However, as a consequence of disadvantages of these methods, the production cost increases dramatically. This article summarizes different biodiesel production methods with a focus on their advantages and disadvantages. The downstream and upstream strategies such as using waste cooking oils, application of non-edible plant oils, plant genetic engineering, using membrane separation technology for biodiesel production, separation and purification, application of crude glycerin as an energy supplement for ruminants, glycerin ultra-purification and their consequent roles in economizing the production process are fully discussed in this article. Copyright © 2010 Elsevier Ltd. All rights reserved.

  18. Polymeric efficiency in remove impurities during cottonseed biodiesel production

    Science.gov (United States)

    Lin, H. L.; Liang, Y. H.; Yan, J.; Lin, H. D.; Espinosa, A. R.

    2016-07-01

    This paper describes a new process for developing biodiesel by polymer from crude cottonseed oil. The study was conducted to examine the effectiveness of the alkali transesterification-flocculation-sedimentation process on fast glycerol and other impurities in the separation from biodiesel by using quaternary polyamine-based cationic polymers SL2700 and polyacylamide cationic polymer SAL1100. The settling velocity of glycerol and other impurities in biodiesel was investigated through settling test experiments; the quality of the biodiesel was investigated by evaluating the viscosity and density. The results revealed that SL2700, SAL1100 and their combination dramatically improved the settling velocity of glycerol and other impurities materials than traditional method. SL 2700 with molecular weight of 0.2 million Da and charge density of 50% then plus SAL1100 with molecular weight of 11 million Da and charge density of 10% induced observable particle aggregation with the best settling performance.

  19. Investigation of Oxidation stability of Pongamia Biodiesel and its blends

    Directory of Open Access Journals (Sweden)

    Gaurav Dwivedi

    2016-03-01

    Full Text Available Biodiesel from Pongamia oil is one of the promising non edible sources in India. But the main problem of using Pongamia biodiesel as fuel is its poor stability characteristics. Poor stability leads to gum formation which further leads to a storage problem of these fuels for a longer period of time. This paper investigates the methodology of improving the stability characteristics of Pongamia biodiesel by blending with diesel and use of the antioxidant Pyrogallol. The experimental investigation shows that blending with diesel and using of antioxidant Pyrogallol improves the stability characteristics of Pongamia biodiesel significantly. Results of the study show that the optimum amount of antioxidant (PY for pure PB20 is 300 ppm to maintain the oxidation stability specification and blending of diesel with Pongamia shows that PB10 requires no additive to maintain its stability characteristics.

  20. Brown Grease to Biodiesel Demonstration Project Report

    Energy Technology Data Exchange (ETDEWEB)

    San Francisco Public Utilities Commission; URS Corporation; Biofuels, Blackgold; Carollo Engineers

    2013-01-30

    Municipal wastewater treatment facilities have typically been limited to the role of accepting wastewater, treating it to required levels, and disposing of its treatment residuals. However, a new view is emerging which includes wastewater treatment facilities as regional resource recovery centers. This view is a direct result of increasingly stringent regulations, concerns over energy use, carbon footprint, and worldwide depletion of fossil fuel resources. Resources in wastewater include chemical and thermal energy, as well as nutrients, and water. A waste stream such as residual grease, which concentrates in the drainage from restaurants (referred to as Trap Waste), is a good example of a resource with an energy content that can be recovered for beneficial reuse. If left in wastewater, grease accumulates inside of the wastewater collection system and can lead to increased corrosion and pipe blockages that can cause wastewater overflows. Also, grease in wastewater that arrives at the treatment facility can impair the operation of preliminary treatment equipment and is only partly removed in the primary treatment process. In addition, residual grease increases the demand in treatment materials such as oxygen in the secondary treatment process. When disposed of in landfills, grease is likely to undergo anaerobic decay prior to landfill capping, resulting in the atmospheric release of methane, a greenhouse gas (GHG). This research project was therefore conceptualized and implemented by the San Francisco Public Utilities Commission (SFPUC) to test the feasibility of energy recovery from Trap Waste in the form of Biodiesel or Methane gas. The research goals are given below: To validate technology performance; To determine the costs and benefits [including economic, socioeconomic, and GHG emissions reduction] associated with co-locating this type of operation at a municipal wastewater treatment plant (WWTP); To develop a business case or model for replication of the

  1. Experimental investigation review of biodiesel usage in bus diesel engine

    OpenAIRE

    Kegl, Breda; Kegl, Marko

    2017-01-01

    This paper assembles and analyses extensive experimental research work conducted for several years in relation to biodiesel usage in a MAN bus Diesel engine with M injection system. At first the most important properties of the actually used neat rapeseed biodiesel fuel and its blends with mineral diesel are discussed and compared to that of mineral diesel. Then the injection, fuel spray, and engine characteristics for various considered fuel blends are compared at various ambient conditions,...

  2. Biodiesel production by chemical or enzymatic esterification of sunflower oil

    Energy Technology Data Exchange (ETDEWEB)

    Passarinho, Paula C.; Rosa, M. Fernanda; Oliveira, A.C.; Pingarilho, M.S.; Beirao, S.G.; Vieira, Ana Maria Soares

    1998-07-01

    In this work, two processes of sunflower oil transesterification, with methanol or ethanol, were studied for biodiesel production: chemical (catalyst- NaOH) and enzymatic (catalyst - rhizomucor miehei lipase). The chemical catalysis proved to be more efficient, having been obtained higher conversion yields and a better quality biodiesel, mainly in the case where methanol was used. The transesterification product had, in all cases, to be purified in order to be used as a diesel substitute.

  3. Technical aspects of biodiesel production from vegetable oils

    OpenAIRE

    Krishnakumar Janahiraman; Venkatachalapathy Karuppannan V.S.; Elancheliyan Sellappan

    2008-01-01

    Biodiesel, a promising substitute as an alternative fuel has gained significant attention due to the finite nature of fossil energy sources and does not produce sulfur oxides and minimize the soot particulate in comparison with the existing one from petroleum diesel. The utilization of liquid fuels such as biodiesel produced from vegetable oil by transesterification process represents one of the most promising options for the use of conventional fossil fuels. In the first step of this experim...

  4. Oil extraction from plant seeds for biodiesel production

    OpenAIRE

    Keneni, Yadessa Gonfa; Marchetti, Jorge Mario

    2017-01-01

    Energy is basic for development and its demand increases due to rapid population growth, urbanization and improved living standards. Fossil fuels will continue to dominate other sources of energy although it is non-renewable and harm global climate. Problems associated with fossil fuels have driven the search for alternative energy sources of which biodiesel is one option. Biodiesel is renewable, non-toxic, environmental-friendly and an economically feasible options to tackle the depleting fo...

  5. TREATMENT OF BIODIESEL WASTEWATER USING YELLOW MUSTARD SEEDS

    OpenAIRE

    SAVCI, Serpil

    2017-01-01

    In thisstudy, removal of original biodiesel wastewater (BOD, COD, oil&greas) by yellow mustard seeds was examined bya batch system. The effect of the adsorption time 300 minutes, adsorbent dose(1.0 g/L) and mixing rate (120 rpm) on the adsorption capacity of pollutants.The applicability of the Langmuir and Freundlich isotherms were examined.According to the data obtained from experiments, biodiesel wastewater can betreated by adsorption using yellow mustard seeds.

  6. Anaerobic Metabolism of Biodiesel and Its Impact on Metal Corrosion

    Science.gov (United States)

    2010-05-05

    Metabolism of Biodiesel and Its Impact on Metal Corrosion Deniz F. Aktas,† Jason S. Lee,‡ Brenda J. Little,‡ Richard I. Ray,‡ Irene A. Davidova...AND SUBTITLE Anaerobic Metabolism of Biodiesel and Its Impact on Metal Corrosion 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6...The intensity of the blackening and distribution of deposits varied with the location within the exposure tank. All coupons exposed to seawater were

  7. Spent coffee grounds for biodiesel production and other applications

    OpenAIRE

    Caetano, Nídia Sá; Silva, Vânia; Melo, Ana C.; Martins, António A.; Mata, Teresa M.

    2014-01-01

    This work evaluates the possibility of using spent coffee grounds (SCG) for biodiesel production and other applications. An experimental study was conducted with different solvents showing that lipid content up to 6 wt% can be obtained from SCG. Results also show that besides biodiesel production, SCG can be used as fertilizer as it is rich in nitrogen, and as solid fuel with higher heating value (HHV) equivalent to some agriculture and wood residues. The extracted lipids were characterized f...

  8. A skeletal mechanism for biodiesel blend surrogates combustion

    International Nuclear Information System (INIS)

    An, H.; Yang, W.M.; Maghbouli, A.; Li, J.; Chua, K.J.

    2014-01-01

    Highlights: • A skeletal biodiesel reaction mechanism with 112 species was constructed. • The developed mechanism contains the CO, NO x and soot formation kinetics. • It was well validated against detailed reaction mechanism and experimental results. • The mechanism is suitable to simulate biodiesel, diesel and their blend fuels. - Abstract: A tri-component skeletal reaction mechanism consisting of methyl decanoate, methyl-9-decenoate, and n-heptane was developed for biodiesel combustion in diesel engine. It comprises 112 species participating in 498 reactions with the CO, NO x and soot formation mechanisms embedded. In this study, a detailed tri-component biodiesel mechanism was used as the start of mechanism reduction and the reduced mechanism was combined with a previously developed skeletal reaction mechanism for n-heptane to integrate the soot formation kinetics. A combined mechanism reduction strategy including the directed relation graph with error propagation and sensitivity analysis (DRGEPSA), peak concentration analysis, isomer lumping, unimportant reactions elimination and reaction rate adjustment methods was employed. The reduction process for biodiesel was performed over a range of initial conditions covering the pressures from 1 to 100 atm, equivalence ratios from 0.5 to 2.0 and temperatures from 700 to 1800 K, whereas for n-heptane, ignition delay predictions were compared against 17 shock tube experimental conditions. Extensive validations were performed for the developed skeletal reaction mechanism with 0-D ignition delay testing and 3-D engine simulations. The results indicated that the developed mechanism was able to accurately predict the ignition delay timings of n-heptane and biodiesel, and it could be integrated into 3-D engine simulations to predict the combustion characteristics of biodiesel. As such, the developed 112-species skeletal mechanism can accurately mimic the significant reaction pathways of the detailed reaction

  9. Biodiesel de microalgas: avanços e desafios

    Directory of Open Access Journals (Sweden)

    André Luiz Custódio Franco

    2013-01-01

    Full Text Available Microalgae biomass has been described by several authors as the raw material with the greatest potential to meet the goals of replacing petroleum diesel by biodiesel while not competing with arable land suitable for food production. Research groups in different countries are seeking the most appropriate production model for productivity, economic viability and environmental sustainability. This review focused on recent advances and challenges of technology for the production of biodiesel from microalgae, including the procedures used to obtain biomass.

  10. Current Status and Prospects of Biodiesel Production from Microalgae

    Directory of Open Access Journals (Sweden)

    Yuhuan Liu

    2012-07-01

    Full Text Available Microalgae represent a sustainable energy source because of their high biomass productivity and ability to remove air and water born pollutants. This paper reviews the current status of production and conversion of microalgae, including the advantages of microalgae biodiesel, high density cultivation of microalgae, high-lipid content microalgae selection and metabolic control, and innovative harvesting and processing technologies. The key barriers to commercial production of microalgae biodiesel and future perspective of the technologies are also discussed.

  11. Small-scale biodiesel production based on a heterogenous technology

    OpenAIRE

    Omberg, Kristian Sørby

    2015-01-01

    In a world where the growing concern for global warming and the problems concerning planet earth is confirmed by the Intergovernmental Panel on Climate Change (IPCC) . Thesearch for alternatives to replace the use of finite fossil fuels and cut green house gas (GHG)emission has commenced. Biodiesel, a biofuel derived from fat and vegetable oil based feedstock is one such alternative. However, a large enough biodiesel production to supply the demand for fuel is beinglimited by cost in...

  12. Aspen Simulation of Diesel-Biodiesel Blends Combustion

    OpenAIRE

    Pérez-Sánchez Armando; Montero-Alpírez Gisela; Ayala-Bautista Ramón; Coronado-Ortega Marcos Alberto; García-González Conrado; Campbell- Ramírez Héctor Enrique

    2015-01-01

    Biodiesel is a fuel produced by transesterification of vegetable oils or animal fats, which currently is gaining attention as a diesel substitute. It represents an opportunity to reduce CO2, SO2, CO, HC, PAH and PM emissions and contributes to the diversification of fuels in Mexico's energetic matrix. The results of the simulation of the combustion process are presented in this paper with reference to an engine specification KUBOTA D600-B, operated with diesel-biodiesel blends. The physicoche...

  13. Numerical analysis of injection characteristics using biodiesel fuel

    OpenAIRE

    Kegl, Breda

    2012-01-01

    This paper deals with numerical analysis of injection process using biodieselžmineral diesel fuel blends with the aim to search for the potentialsto reduce engine harmful emissions. The considered fuels are neat biodiesel from rapeseed oil and its blends with mineral diesel D2. For the numerical analysis a one-dimensional mathematical model is employed. In order to model accurately the investigated fuels, the employed empirical expressionsfor their properties are determined by experiments. To...

  14. A comprehensive review on biodiesel purification and upgrading

    OpenAIRE

    Hamed Bateni; Alireza Saraeian; Chad Able

    2017-01-01

    Serious environmental concerns regarding the use of fossil-based fuels have raised awareness regarding the necessity of alternative clean fuels and energy carriers. Biodiesel is considered a clean, biodegradable, and non-toxic diesel substitute produced via the transesterification of triglycerides with an alcohol in the presence of a proper catalyst. After initial separation of the by-product (glycerol), the crude biodiesel needs to be purified to meet the standard specifications prior to mar...

  15. Physico-chemical characterization of biodiesel from pests attacked corn oil; Caracterizacao fisico-quimica do biodiesel de oleo de milho danificado por pragas

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Fabia M.; Correa, Paulo C.; Martins, Marcio A.; Santos, Silmara B.; Damian, Amanda D. [Universidade Federal de Vicosa (UFV), MG (Brazil)], Emails: copace@ufv.br, aredes@ufv.br, syllmara@vicosa.ufv.br

    2009-07-01

    The biodiesel is a renewable energy source alternative to fossil fuels. The biodiesel synthesis can be made by many types of triglycerides transesterification, it is possible to use this biofuel in vehicles if it has the quality required from Agencia Nacional de Petroleo, Gas Natural e Biocombustiveis (ANP). Searching an application for pests attacked corn, there is feasibility technical for the biodiesel production from this corn oil. The biodiesel synthesis was made through ethyl transesterification process with alkaline catalyst using ethanol. The biodiesel physical-chemical characterization was performed using ANP methods. (author)

  16. Oxidative stability of biodiesel blends derived from waste frying oils

    Directory of Open Access Journals (Sweden)

    Michael Feroldi

    2017-07-01

    Full Text Available The high cost of biodiesel production is mainly linked to the price of raw material.This factor has favored the use of alternative fats and oils such as those used in frying. Since biodiesel can be obtained from several vegetable and animal raw materials, the physicochemical characteristics of the fuel may vary considerably. One of these characteristics is the fatty acid composition. It directly affects the oxidative stability of biodiesel, which can be impaired when the fuel undergoes exposure to sunlight, metals, oxygen and high temperatures. In order to improve the oxidative stability of biodiesels produced from waste frying oil some studies involving blends of different raw materials have been carried out. In this sense, this work aimed to assess the characteristics resulting from the blending of soybean waste frying oil with other waste biodiesels in what concerns to oxidation. The blends of fatty materials were obtained by means of a 2² factorial design. The induction periods of biodiesel blends were enough to meet the ASTM D6751 standard. Swine fat was responsible for the increase in the induction period values.

  17. Characteristics of paddy operations with biodiesel fuelled tractor

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Y.; Park, S.H.; Kim, C.K.; Im, D.H.; Kim, H.J.; Chung, S.C. [National Academy of Agricultural Science, Seodundong, Suwon (Korea, Democratic People' s Republic of); Kim, S.S. [Daedong Industrial Co., Chang Nyong-Kun, Kyungnam (Korea, Democratic People' s Republic of)

    2010-07-01

    This paper reported on a study in which biofuels were tested for their power and competitiveness in various paddy operations, such as plowing and rotary tilling of paddy fields. The study considered the use of diesel fuel as well as 20 per cent biodiesel (BD20) and 100 per cent biodiesel (BD100) as an alternative fuel for tractors. Ignition problems or abrupt stopping were not monitored during operations of plowing, rotary tilling and travelling on the road. According to tractor power take-off (PTO) test codes, there was no considerable power difference between the 3 fuels. However, fuel consumption rates were quite different between the biodiesels and diesel fuel in the paddy works. Fuel consumption increased when biodiesel content increased. Approximately 35 to 40 per cent more fuel was needed for rotary tilling operations than plowing operations. Within the operations, the maximum difference occurred during the rotary tilling of wet paddy fields. This difference was as high as 20 per cent , between BD100 and diesel fuel. In terms of exhaust gases, more carbon dioxide was discharged from diesel fuel than biodiesels, but more nitrous oxide was discharged with biodiesels. It was difficult to differentiate quantities of carbon monoxide between the 3 different fuels.

  18. Different purification methods and quality of sunflower biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Pighinelli, A.L.M.T.; Park, K.J. [Campinas State Univ., Sao Paulo (Brazil). School of Agricultural Engineering; Ferrari, R.A.; Miguel, A.M.R.O. [Food Technology Inst., Sao Paulo (Brazil)

    2010-07-01

    Biodiesel is derived from triacylglycerides and is produced primarily through transesterification, a chemical reaction of vegetable oils with alcohol, methanol or ethanol. The cost of raw material should be considered since 85 per cent of production cost is related to vegetable oil. The purpose of this study was to evaluate oil expression of sunflower seed. It also examined the sunflower crude oil as a raw material for biodiesel by transesterification in both laboratory and pilot scale studies. Three different biodiesel purification methods were examined. The best result for oil expelling (68.4 per cent) at the experimental stage was obtained for seeds with a moisture content of 6.9 per cent at 25 degrees C and at a screw speed of 114 rpm. For biodiesel production at the laboratory scale, the best result for oil expelling was 87.5 per cent. It was obtained with an ethanol:oil molar ratio of 4.7:1 and with a 4.42 per cent catalyst concentration related to the quantity of oil that had to be transesterified. The experimental condition was applied at a bigger scale with a batch stirred tank reactor. For purification with washing, the biodiesel yield was 84.2 per cent. Purification with silica resulted in a yield of 84.6 per cent. A better quality biofuel was obtained through distillation of biodiesel.

  19. Oil extraction from plant seeds for biodiesel production

    Directory of Open Access Journals (Sweden)

    Yadessa Gonfa Keneni

    2017-04-01

    Full Text Available Energy is basic for development and its demand increases due to rapid population growth, urbanization and improved living standards. Fossil fuels will continue to dominate other sources of energy although it is non-renewable and harm global climate. Problems associated with fossil fuels have driven the search for alternative energy sources of which biodiesel is one option. Biodiesel is renewable, non-toxic, environmental-friendly and an economically feasible options to tackle the depleting fossil fuels and its negative environmental impact. It can be produced from vegetable oils, animal fats, waste oils and algae. However, nowadays, the major feedstocks of biodiesel are edible oils and this has created food vs fuel debate. Therefore, the future prospect is to use non-edible oils, animal fats, waste oils and algae as feedstock for biodiesel. Selection of non-expensive feedstock and the extraction and preparation of oil for biodiesel production is a crucial step due to its relevance on the overall technology. There are three main conventional oil extraction methods: mechanical, chemical/solvent and enzymatic extraction methods. There are also some newly developed oil extraction methods that can be used separately or in combination with the conventional ones, to overcome some disadvantages of the conventional oil extraction methods. This review paper presents, compare and discusses different potential biofuel feedstocks, various oil extraction methods, advantages and disadvantages of different oil extraction methods, and propose future prospective for the improvement of oil extraction methods and sustainability of biodiesel production and utilization.

  20. Breathing easier? The known impacts of biodiesel on air quality.

    Science.gov (United States)

    Traviss, Nora

    2012-05-01

    Substantial scientific evidence exists on the negative health effects of exposure to petroleum diesel exhaust. Many view biodiesel as a 'green', more environmentally friendly alternative fuel, especially with respect to measured reductions of particulate matter in tailpipe emissions. Tailpipe emissions data sets from heavy-duty diesel engines comparing diesel and biodiesel fuels provide important information regarding the composition and potential aggregate contribution of particulate matter and other pollutants to regional airsheds. However, exposure - defined in this instance as human contact with tailpipe emissions - is another key link in the chain between emissions and human health effects. Although numerous biodiesel emissions studies exist, biodiesel exposure studies are nearly absent from the literature. This article summarizes the known impacts of biodiesel on air quality and health effects, comparing emissions and exposure research. In light of rapidly changing engine, fuel and exhaust technologies, both emissions and exposure studies are necessary for developing a fuller understanding of the impact of biodiesel on air quality and human health.

  1. Sustaining Biodiesel Production via Value-Added Applications of Glycerol

    Directory of Open Access Journals (Sweden)

    Omotola Babajide

    2013-01-01

    Full Text Available The production of biofuels worldwide has been significant lately due to the shift from obtaining energy from nonrenewable energy (fossil fuels to renewable sources (biofuels. This energy shift arose as a result of the disturbing crude petroleum price fluctuations, uncertainties about fossil fuel reserves, and greenhouse gas (GHG concerns. With the production of biofuels increasing considerably and the current global biodiesel production from different feedstock, reaching about 6 billion liters per year, biodiesel production costs have been highly dependent on feedstock prices, ranging from 70 to 25; of total production costs, and in comparison with the conventional diesel fuel, the biodiesel is currently noncompetitive. An efficient production process is, therefore, crucial to lowering biodiesel production costs. The question of sustainability, however, arises, taking into account the African diverse conditions and how vital concerns need to be addressed. The major concern about biodiesel production costs can be reduced by finding value-added applications for its glycerol byproduct. This paper, thus, provides an overview of current research trends that could overcome the major hurdles towards profitable commercialization of biodiesel and also proposes areas of opportunity probable to capitalize the surplus glycerol obtained, for numerous applications.

  2. Evaluation of Biodiesel Production, Engine Performance, and Emissions

    Science.gov (United States)

    Gürü, Metin; Keskïn, Ali

    2016-08-01

    Nowadays, to decrease environmental pollution and dependence on fossil-based fuels, research on alternative renewable energy sources has been increasing. One such renewable energy source is biodiesel, which is used as an alternative fuel for diesel engines. Biodiesel is renewable, nontoxic, biodegradable, and environmentally friendly. Biodiesel is domestically produced from vegetable oil (edible or nonedible), animal fat, and used cooking oils. In the biodiesel production process, oil or fat undergoes transesterification reaction through use of simple alcohols such as methanol, ethanol, propanol, butanol, etc. Use of methanol is most feasible because of its low cost, and physical and chemical advantages. Acid catalysis, alkali catalysis, and enzyme catalysis are usually used to improve the reaction rate and yield. Glycerol is a byproduct of the reaction and can be used as an industrial raw material. In this study, biodiesel production methods (direct use, pyrolysis, microemulsion, transesterification, supercritical processes, ultrasound- assisted, and microwave-assisted) and types of catalyst (homogeneous, heterogeneous, and enzyme) have been evaluated and compared. In addition, the effects of biodiesel and its blends on diesel engine performance and exhaust emissions are described and reviewed.

  3. An updated comprehensive techno-economic analysis of algae biodiesel.

    Science.gov (United States)

    Nagarajan, Sanjay; Chou, Siaw Kiang; Cao, Shenyan; Wu, Chen; Zhou, Zhi

    2013-10-01

    Algae biodiesel is a promising but expensive alternative fuel to petro-diesel. To overcome cost barriers, detailed cost analyses are needed. A decade-old cost analysis by the U.S. National Renewable Energy Laboratory indicated that the costs of algae biodiesel were in the range of $0.53-0.85/L (2012 USD values). However, the cost of land and transesterification were just roughly estimated. In this study, an updated comprehensive techno-economic analysis was conducted with optimized processes and improved cost estimations. Latest process improvement, quotes from vendors, government databases, and other relevant data sources were used to calculate the updated algal biodiesel costs, and the final costs of biodiesel are in the range of $0.42-0.97/L. Additional improvements on cost-effective biodiesel production around the globe to cultivate algae was also recommended. Overall, the calculated costs seem promising, suggesting that a single step biodiesel production process is close to commercial reality. Copyright © 2012 Elsevier Ltd. All rights reserved.

  4. Enhancing Biodiesel from Kemiri Sunan Oil Manufacturing using Ultrasonics

    Science.gov (United States)

    Supriyadi, Slamet; Purwanto; Anggoro, Didi Dwi; Hermawan

    2018-02-01

    Kemiri Sunan (Reutalis trisperma (Blanco) Airy Shaw) is a potential plant to be developed as biodiesel feedstock. The advantage of Kemiri Sunan seeds when compared to other biodiesel raw materials is their high oil content. This plant is also very good for land conservation. Due the increasingly demand for biodiesel, research and new methods to increase its biodiesel production continue to be undertaken. The weakness of conventional biodiesel manufacturing process is in the mixing process in which mechanical stirring and heating in the trans-esterification process require more energy and a longer time. A higher and stronger mixing process is required to increase the contact area between the two phases of the mixed substance to produce the emulsion. Ultrasonic is a tool that can be useful for a liquid mixing process that tends to be separated. Ultrasonic waves can cause mixing intensity at the micro level and increase mass transfer, so the reaction can be performed at a much faster rate. This study is to figure out the effect of ultrasonic irradiation on the transesterification process of biodiesel from Kemiri Sunan Oil.

  5. Castor oil biodiesel as an alternative fuel for diesel engines

    International Nuclear Information System (INIS)

    Benavides, Alirio; Benjumea, Pedro; Pashova, Veselina

    2007-01-01

    In this paper, a study related to the production and use of castor oil biodiesel is presented. The maximum methyl esters yield of the castor oil transesterification reaction is obtained under the following conditions: ambient temperature, a molar ratio of methanol to vegetable oil equal to 9 and a catalyst percentage equal to 0.8%. The castor oil biodiesel can be blended with petroleum diesel as far as 15% in such way that the resulting blend complies with national and international technical standards for diesel fuels. Its high viscosity becomes the main difficulty for using castor oil biodiesel in engines. However this biofuel exhibits excellent cold flow properties (low values of cloud and pour points). The motor tests using castor oil biodiesel petroleum diesel blends, for the biodiesel proportion tested; show that a biodiesel percentage increase leads to an increase in the specific fuel consumption, a decrease in the fuel air ratio, a slight decrease in smoke opacity, while the fuel conversion efficiency and the CO and CO 2 emissions practically remain constants

  6. Cost analysis of simulated base-catalyzed biodiesel production processes

    International Nuclear Information System (INIS)

    Tasić, Marija B.; Stamenković, Olivera S.; Veljković, Vlada B.

    2014-01-01

    Highlights: • Two semi-continuous biodiesel production processes from sunflower oil are simulated. • Simulations were based on the kinetics of base-catalyzed methanolysis reactions. • The total energy consumption was influenced by the kinetic model. • Heterogeneous base-catalyzed process is a preferable industrial technology. - Abstract: The simulation and economic feasibility evaluation of semi-continuous biodiesel production from sunflower oil were based on the kinetics of homogeneously (Process I) and heterogeneously (Process II) base-catalyzed methanolysis reactions. The annual plant’s capacity was determined to be 8356 tonnes of biodiesel. The total energy consumption was influenced by the unit model describing the methanolysis reaction kinetics. The energy consumption of the Process II was more than 2.5 times lower than that of the Process I. Also, the simulation showed the Process I had more and larger process equipment units, compared with the Process II. Based on lower total capital investment costs and biodiesel selling price, the Process II was economically more feasible than the Process I. Sensitivity analysis was conducted using variable sunflower oil and biodiesel prices. Using a biodiesel selling price of 0.990 $/kg, Processes I and II were shown to be economically profitable if the sunflower oil price was 0.525 $/kg and 0.696 $/kg, respectively

  7. Design and optimisation of purification procedure for biodiesel washing

    Directory of Open Access Journals (Sweden)

    S.B. Glišić

    2009-09-01

    Full Text Available Almost complete methanolysis of triglycerides is usually not enough to fulfil the strict standards of biodiesel quality. A key step in this process is neutralization of alkali (catalyst followed by the washing procedure necessary for removing different impurities such as traces of catalyst and methanol and removal of soaps and glycerol from esters phase. The washing with hot water is still widely used in many industrial units for the biodiesel production. In this study, different procedures of biodiesel washing using hot water were investigated. The orto-phosphoric acid was suggested as the best compound for alkali catalyst (sodium hydroxide neutralization. The main goal of the performed analysis was to minimize the water usage in the washing-neutralization step during the biodiesel production. Such solution would make the process of biodiesel synthesis more economical taking into account the decrease of energy consumed for evaporation of water during the final product purification, as well as more acceptable procedure related to the impact on environment (minimal waste water release. Results of the performed simulation of the washing process supported by original experimental data suggested that neutralization after the optimized washing process of the methyl ester layer could be the best solution. The proposed washing procedure significantly decreases the amount of waste water giving at the same time the desired purity of final products (biodiesel and glycerol. The simulation of the process was performed using ASPEN plus software supported by ELCANTREL and UNIQUAC procedure of required properties calculation

  8. Optimization of emergy sustainability index for biodiesel supply network design

    International Nuclear Information System (INIS)

    Ren, Jingzheng; Tan, Shiyu; Yang, Le; Goodsite, Michael Evan; Pang, Chengfang; Dong, Lichun

    2015-01-01

    Highlights: • A MINLP model for designing sustainable biodiesel supply network is developed. • Emergy sustainability index is used as the objective to be maximized. • Multiple alternatives in each stage of biodiesel supply network are considered. • Life cycle perspective is incorporated in the design of biodiesel supply network. - Abstract: Sustainability is an important and difficult consideration for the stakeholders/decision-makers when planning a biofuel supply network. In this paper, a Mixed-Integer Non-linear Programming (MINLP) model was developed with the aim to help the stakeholders/decision-maker to select the most sustainable design. In the proposed model, the emergy sustainability index of the whole biodiesel supply networks in a life cycle perspective is employed as the measure of the sustainability, and multiple feedstocks, multiple transport modes, multiple regions for biodiesel production and multiple distribution centers can be considered. After describing the process and mathematic framework of the model, an illustrative case was studied and demonstrated that the proposed methodology is feasible for finding the most sustainable design and planning of biodiesel supply chains

  9. Production of Biodiesel from Waste Vegetable Oil via KM Micromixer

    Directory of Open Access Journals (Sweden)

    M. F. Elkady

    2015-01-01

    Full Text Available The production of biodiesel from waste vegetable oils through its pretreatment followed by transesterification process in presence of methanol was investigated using a KM micromixer reactor. The parameters affecting biodiesel production process such as alcohol to oil molar ratio, catalyst concentration, the presence of tetrahydrofuran (THF as a cosolvent, and the volumetric flow rates of inlet fluids were optimized. The properties of the produced biodiesel were compared with its parent waste oil through different characterization techniques. The presence of methyl ester groups at the produced biodiesel was confirmed using both the gas chromatography-mass spectrometry (GC-MS and the infrared spectroscopy (FT-IR. Moreover, the thermal analysis of the produced biodiesel and the comparable waste oil indicated that the product after the transesterification process began to vaporize at 120°C which makes it lighter than its parent oil which started to vaporize at around 300°C. The maximum biodiesel production yield of 97% was recorded using 12 : 1 methanol to oil molar ratio in presence of both 1% NaOH and THF/methanol volume ratio 0.3 at 60 mL/h flow rate.

  10. Biodiesel Production from Microalgae by Extraction – Transesterification Method

    Directory of Open Access Journals (Sweden)

    Nguyen Thi Phuong Thao

    2013-11-01

    Full Text Available The environmental impact of using petroleum fuels has led to a quest to find a suitable alternative fuel source. In this study, microalgae were explored as a highly potential feedstock to produce biodiesel fuel. Firstly, algal oil is extracted from algal biomass by using organic solvents (n–hexan.  Lipid is contained in microalgae up to 60% of their weight. Then, Biodiesel is created through a chemical reaction known as transesterification between algal oil and alcohol (methanol with strong acid (such as H2SO4 as the catalyst. The extraction – transesterification method resulted in a high biodiesel yield (10 % of algal biomass and high FAMEs content (5.2 % of algal biomass. Biodiesel production from microalgae was studied through experimental investigation of transesterification conditions such as reaction time, methanol to oil ration and catalyst dosage which are deemed to have main impact on reaction conversion efficiency. All the parameters which were characterized for purified biodiesel such as free glycerin, total glycerin, flash point, sulfur content were analyzed according to ASTM standardDoi: http://dx.doi.org/10.12777/wastech.1.1.6-9Citation:  Thao, N.T.P., Tin, N.T., and Thanh, B.X. 2013. Biodiesel Production from Microalgae by Extraction – Transesterification Method. Waste Technology 1(1:6-9. Doi: http://dx.doi.org/10.12777/wastech.1.1.6-9

  11. Study of the drivers of competitiveness of the Brazilian biodiesel; Estudo dos direcionadores de competitividade do biodiesel brasileiro

    Energy Technology Data Exchange (ETDEWEB)

    Cesar, Aldara da Silva; Batalha, Mario Otavio [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil). Dept. de Engenharia de Producao; Monteiro, Marcos Roberto [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil). Centro de Caracterizacao e Desenvolvimento de Materiais

    2008-07-01

    In the increasingly important role that the biofuel market takes in the new dynamic global competition, biodiesel emerges as a real alternative of implantation. In Brazil, this interest is not different. However, despite of biodiesel's enormous potential, there is a number of uncertainties that need to be investigated in order to produce a biodiesel which has its unique specifications and international quality recognized. The aim of this article is twofold: first, the information systematization of the Brazilian biodiesel production chain; and second, the analysis of drivers of competitiveness that affect that same production chain. Through the theory of systemic approach, each driver of competitiveness is described and its competitive environment is analyzed. The range of different raw materials and possible technological routes present numerous challenges for the agents of this chain. What increases the relevance of studies such as this is the notion that investigating the drives of competitiveness is the first step in overcoming these challenges. (author)

  12. Biodiesel exhaust: the need for a systematic approach to health effects research.

    Science.gov (United States)

    Larcombe, Alexander N; Kicic, Anthony; Mullins, Benjamin J; Knothe, Gerhard

    2015-10-01

    Biodiesel is a generic term for fuel that can be made from virtually any plant or animal oil via transesterification of triglycerides with an alcohol (and usually a catalyst). Biodiesel has received considerable scientific attention in recent years, as it is a renewable resource that is directly able to replace mineral diesel in many engines. Additionally, some countries have mandated a minimum biodiesel content in all diesel fuel sold on environmental grounds. When combusted, biodiesel produces exhaust emissions containing particulate matter, adsorbed chemicals and a range of gases. In many cases, absolute amounts of these pollutants are lower in biodiesel exhaust compared with mineral diesel exhaust, leading to speculation that biodiesel exhaust may be less harmful to health. Additionally, engine performance studies show that the concentrations of these pollutants vary significantly depending on the renewable oil used to make the biodiesel and the ratio of biodiesel to mineral diesel in the fuel mix. Given the strategic and legislative push towards the use of biodiesel in many countries, a concerning possibility is that certain biodiesels may produce exhaust emissions that are more harmful to health than others. This variation suggests that a comprehensive, systematic and comparative approach to assessing the potential for a range of different biodiesel exhausts to affect health is urgently required. Such an assessment could inform biodiesel production priorities, drive research and development into new exhaust treatment technologies, and ultimately minimize the health impacts of biodiesel exhaust exposure. © 2015 Asian Pacific Society of Respirology.

  13. Soy Biodiesel Emissions Have Reduced Inflammatory Effects ...

    Science.gov (United States)

    Toxicity of exhaust from combustion of petroleum diesel (BO), soy-based biodiesel (B100), or a 20% biodiesel/80% petrodiesel mix (B20) was compared in healthy and house dust mite (HDM)-allergic mice. Fuel emissions were diluted to target fine particulate matter (PM2.5) conrentrations of 50, 150, or 500 µg/m(3). Studies in healthy mice showed greater levels of neutrophils and MIP-2 in bronchoaeolar lavage (BAL) fluid 2 h after a single 4-h exposure to BO compared with mice exposed to B20 or B100. No consistent differences in BAL cells and biochemistry, or hematological parameters, were observed after 5 d or 4 weeks of exposure to any of the emissions. Air-exposed HDM-allergc mice had significantly increased responsiveness to methacholine aerosol challenge compared with non-allergic mice. Exposure to any of the emissions for 4 weeks did not further increase responsiveness in either non-allergic or HDM­ allergic mice, and few parameters of allergic inflammation in BAL fluid were altered. Lung and nasal pathology were not significantly different among BO-, B20-, or B100-exposed groups. In HDM-allergic mice, exposure to BO, but not B20 or B100, significantly increased resting peribronchiolar lymph node cell proliferation and production of TH2 cytokines (IL-4, IL-5, and IL-13) and IL-17 in comparison with air-exposed allergic mice. These results suggest that diesel exhaust at a relatively high concentration (500 µg/m(3)) can induce inflammation acutely in healthy m

  14. Production of biodiesel from vegetable oils

    Directory of Open Access Journals (Sweden)

    Luque, Susana

    2008-03-01

    Full Text Available Biodiesel is produced by transesterification of triglycerides present in animal fat or vegetable oils, by displacing glycerine with a low molar mass alcohol. This resulting ester mixture has physico-chemical properties similar to those of petroleum diesel. This paper reviews the synthetic paths that lead to biodiesel by means of the catalytic transesterification of vegetable oils. Although methyl esters are at present the only ones produced at industrial scale, the use of ethanol, which can also be obtained from renewable resources, has been considered, since it would generate a cleaner and more biocompatible fuel.El biodiésel se produce mediante la transesterificación de triglicéridos, presentes en grasas animales o aceites vegetales, en un proceso en el que un alcohol de bajo peso molecular desplaza a la glicerina. La mezcla de esteres así resultante posee unas propiedades físico-químicas similares a las del diésel procedente de petróleo. En este artículo se revisan las vías de síntesis de biodiésel mediante la transesterificación catalítica de aceites vegetales. Aunque actualmente a escala industrial solo se producen ésteres metílicos, también se ha considerado el uso de etanol, ya que éste se obtiene también de fuentes renovables, generando así un combustible más limpio y biocompatible.

  15. Sustainable biocatalytic biodiesel production : A thermodynamic analysis

    Energy Technology Data Exchange (ETDEWEB)

    Guezel, G.

    2012-09-15

    In the present thesis it was aimed at achieving thermodynamic analysis of reactions involved in enzymatic biodiesel production with specific focus on chemical and phase equilibria of reactive systems. Lipase-catalyzed biodiesel production (biocatalytic ethanolysis) presents significant advantages: Easy recovery of glycerol, no complex down-processing operations for elimination of catalyst and salt, and requires less organic solvent and lower energy consumption compared with conventional chemical methods. In overall, the major aims of this thesis were evaluating and subsequently finding feasible solutions to the questions emerged during the corresponding studies that have been performed worldwide. Some of the questions that were answered as appropriate as possible can be listed as follows: 1) What is the solubility of EtOH in vegetable oils and in FAEE blends and how does it change with temperature? 2) Is it possible to prevent denaturing impact of EtOH on biocatalysts? 3) What are the feedstock content (water and FFA) impacts on glycerol and EtOH miscibility with ester species? 4) Is it necessary removing glycerol by-product simultaneously? 5) Is it feasible providing monophasic or homogeneous reaction media that procure lower external mass transfer resistance? 6) What are the moisture absorption limits of FAAE species? 7) How are the interactions of reactive species in terms of miscibility/immiscibility phenomena? 8) Is it thermodynamically feasible providing monophasic reaction media? 9) How can LLE and VLE phase behaviors help to determine optimum reaction conditions? 10) How can the results of LLE and VLE studies be used so as to determine appropriate refining operations? (LN)

  16. NOx Solutions for Biodiesel: Final Report; Report 6 in a Series of 6

    Energy Technology Data Exchange (ETDEWEB)

    McCormick, R. L.; Alvarez, J. R.; Graboski, M. S.

    2003-02-01

    A number of studies have shown substantial particulate matter (PM) reductions for biodiesel, but also a significant increase in nitrogen oxides (NOx) emissions. This study examines a number of approaches for NOx reduction from biodiesel.

  17. Concentration measurements of biodiesel in engine oil and in diesel fuel

    International Nuclear Information System (INIS)

    Mäder, A; Eskiner, M; Burger, C; Rossner, M; Krahl, J; Ruck, W

    2012-01-01

    This work comprised a method for concentration measurements of biodiesel in engine oil as well as biodiesel in diesel fuel by a measurement of the permittivity of the mixture at a frequency range from 100 Hz to 20 kHz. For this purpose a special designed measurement cell with high sensitivity was designed. The results for the concentration measurements of biodiesel in the engine oil and diesel fuel shows linearity to the measurement cell signal for the concentration of biodiesel in the engine oil between 0.5% Vol. to 10% Vol. and for biodiesel in the diesel fuel between 0% Vol. to 100% Vol. The method to measure the concentration of biodiesel in the engine oil or the concentration of biodiesel in the diesel fuel is very accurate and low concentration of about 0.5% Vol. biodiesel in engine oil or in diesel fuel can be measured with high accuracy.

  18. The effect of synthetic antioxidants on the oxidative stability of biodiesel

    CSIR Research Space (South Africa)

    Focke, WW

    2012-04-01

    Full Text Available Biodiesels were prepared using base catalyzed methanolysis of sunflower, soybean and canola oils. Rancimat oxidative stability measurements showed that the induction period (IP) for neat canola biodiesel conformed to EN 14214, the European...

  19. The characteristics of performance and exhaust emissions of a diesel engine using a biodiesel with antioxidants.

    Science.gov (United States)

    Ryu, Kyunghyun

    2010-01-01

    The aim of this study is to investigate the effects of antioxidants on the oxidation stability of biodiesel fuel, the engine performance and the exhaust emissions of a diesel engine. Biodiesel fuel used in the study was derived from soybean oil. The results show that the efficiency of antioxidants is in the order TBHQ>PrG>BHA>BHT>alpha-tocopherol. The oxidative stability of biodiesel fuel attained the 6-h quality standard with 100 ppm TBHQ and with 300 ppm PrG in biodiesel fuel. Combustion characteristics and exhaust emissions in diesel engine were not influenced by the addition of antioxidants in biodiesel fuel. The BSFC of biodiesel fuel with antioxidants decreased more than that of biodiesel fuel without antioxidants, but no trends were observed according to the type or amount of antioxidant. Antioxidants had few effects on the exhaust emissions of a diesel engine running on biodiesel.

  20. Qualidade de biodiesel de soja, mamona e blendas durante armazenamento

    Directory of Open Access Journals (Sweden)

    Marco Aurélio R. Melo

    2016-12-01

    Full Text Available Objetivou-se monitorar o armazenamento dos biodieseis provenientes da transesterificação homogênea alcalina do óleo de soja e mamona via rota metílica, avaliando a indução oxidativa pela norma EN14112 e pelo método PetroOxy durante o período de 120 dias, também observou-se o comportamento dos biodieseis inseridos em blendas nas proporções de 20, 30, 40 e 50% v/v de biodiesel de mamona ao biodiesel de soja denominadas de M20, M30, M40 e M50 (em recipientes de aço-carbono fechado. Conforme análises físico-químicas, as especificações para ambos biodiesel e blendas satisfizeram as exigências dos limites permitidos pelo Regulamento Técnico nº 14/2012 da Agência Nacional do Petróleo, Gás Natural e Biocombustíveis. Exceção das análises de estabilidade oxidativa (M0, M20, M30 e M40, do índice de acidez após 60 dias (M50, após 90 dias (M40 e M50, após 120 dias (M100 e da viscosidade cinemática (M40, M50 e M100 que apresentaram valores fora dos limites estabelecidos pela norma. As propriedades fluidodinâmicas apresentaram comportamentos semelhantes para os biodieseis metílicos e blendas, assim, nestas concentrações o biodiesel metílico de mamona atua como um aditivo natural ao biodiesel metílico de soja. Através do método EN 14112 verificou-se que a blenda M50 é mais resistente ao processo de oxidação durante armazenamento de 120 dias.Quality of biodiesel soy, castor beans and blends during storageAbstract: The objective of the study was to monitor the storage of biodiesels from alkaline homogeneous transesterification of soybean and castor oil via methyl route, and to evaluate the oxidative induction by the EN14112 standard and the PetroOxy method over the period of 120 days. We observed the behavior of the inserted biodiesels in blends in the ratios of 20, 30, 40 and 50% v / v biodiesel from castor beans of soybean biodiesel named M20, M30, M40 and M50 (closed carbon steel containers . As physical and chemical

  1. Chitosan and Its Derivatives Applied in Harvesting Microalgae for Biodiesel Production: An Outlook

    OpenAIRE

    Guanyi Chen; Liu Zhao; Yun Qi; Yuan-Lu Cui

    2014-01-01

    Although oil-accumulating microalgae are a promising feedstock for biodiesel production, large-scale biodiesel production is not yet economically feasible. As harvesting accounts for an important part of total production cost, mass production of microalgae biodiesel requires an efficient low-energy harvesting strategy so as to make biodiesel production economically attractive. Chitosan has emerged as a favorable flocculating agent in harvesting of microalgae. The aim of this paper is to revie...

  2. Degradation of acrylonitrile butadiene rubber and fluoroelastomers in rapeseed biodiesel and hydrogenated vegetable oil

    OpenAIRE

    Akhlaghi, Shahin

    2017-01-01

    Biodiesel and hydrotreated vegetable oil (HVO) are currently viewed by the transportation sector as the most viable alternative fuels to replace petroleum-based fuels. The use of biodiesel has, however, been limited by the deteriorative effect of biodiesel on rubber parts in automobile fuel systems. This work therefore aimed at investigating the degradation of acrylonitrile butadiene rubber (NBR) and fluoroelastomers (FKM) on exposure to biodiesel and HVO at different temperatures and oxygen ...

  3. Production of FAME biodiesel in E. coli by direct methylation with an insect enzyme

    OpenAIRE

    Sherkhanov, Saken; Korman, Tyler P.; Clarke, Steven G; Bowie, James U.

    2016-01-01

    Most biodiesel currently in use consists of fatty acid methyl esters (FAMEs) produced by transesterification of plant oils with methanol. To reduce competition with food supplies, it would be desirable to directly produce biodiesel in microorganisms. To date, the most effective pathway for the production of biodiesel in bacteria yields fatty acid ethyl esters (FAEEs) at up to ~1.5?g/L. A much simpler route to biodiesel produces FAMEs by direct S-adenosyl-L-methionine (SAM) dependent methylati...

  4. Comparative Analysis of Biodegradability of Biodiesel obtained by Conventional and Non-Conventional Methods

    OpenAIRE

    Nagaraja Y. P; Chandrashekhar Biradar

    2015-01-01

    Biodiesel is an alternative to conventional diesel fuel made from renewable resources. No engine modifications are required to use biodiesel in place of crude oil-based diesel. The use of biodiesel resulted in lower emissions of unburned hydrocarbons, carbon monoxide and particulate matter. Biodiesel also increased catalytic converter efficiency in reducing particulate emissions. Chemical characterization also revealed lower levels of some toxic and reactive hydrocarbo...

  5. Dynamics of Peroxy and Alkenyl Radicals Undergoing Competing Rearrangements in Biodiesel Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Dibble, Theodore S. [State Univ. of New York (SUNY), Syracuse, NY (United States)

    2016-03-24

    Biodiesel fuel is increasingly being used worldwide. Although we have a fair understanding of the molecular details of the chemistry of peroxy radicals derived from alkanes, biodiesel fuels contain ester and olefin groups which significantly impact the thermodynamics and kinetics of biodiesel ignition. The broader goal of this research is to carry out systematic computational studies of the elementary kinetics of the chemistry of ROO•, QOOH and •OOQOOH compounds that are models for biodiesel ignition.

  6. Tri-fuel (diesel-biodiesel-ethanol) emulsion characterization, stability and the corrosion effect

    Science.gov (United States)

    Low, M. H.; Mukhtar, N. A. M.; Yohaness Hagos, Ftwi; Noor, M. M.

    2017-10-01

    This paper presents the result of experimenting emulsified tri-fuel in term of stability, physico-chemical properties and corrosion effect on three common metals. The results were interpreted in terms of the impact of five minutes emulsification approach. Tri-fuel emulsions were varied in proportion ratio consist of biodiesel; 0%, 5%, 10%, and ethanol; 5%, 10%, 15%. Fuel characterization includes density, calorific value, flash point, and kinematic viscosity. Flash point of tri-fuel emulsion came with range catalog. Calorific value of tri-fuel emulsion appeared in declining pattern as more ethanol and biodiesel were added. Biodiesel promoted flow resistance while ethanol with opposite effect. 15% ethanol content in tri-fuel emulsion separated faster than 10% ethanol content but ethanol content with 5% yield no phase separation at all. Close cap under static immersion with various ratio of tri-fuel emulsions for over a month, corrosiveness attack was detected via weight loss technique on aluminum, stainless steel and mild steel.

  7. Biodiesel production from algae grown on food industry wastewater.

    Science.gov (United States)

    Mureed, Khadija; Kanwal, Shamsa; Hussain, Azhar; Noureen, Shamaila; Hussain, Sabir; Ahmad, Shakeel; Ahmad, Maqshoof; Waqas, Rashid

    2018-04-10

    Algae have an ample potential to produce biodiesel from spent wash of food industry. In addition, it is cheaper and presents an environment friendly way to handle food industry wastewater. This study was conducted to optimize the growth of microalgal strains and to assess biodiesel production potential of algae using untreated food industry wastewater as a source of nutrients. The food industry wastewater was collected and analyzed for its physicochemical characteristics. Different dilutions (10, 20, 40, 80, and 100%) of this wastewater were made with distilled water, and growth of two microalgal strains (Cladophora sp. and Spyrogyra sp.) was recorded. Each type of wastewater was inoculated with microalgae, and biomass was harvested after 7 days. The growth of both strains was also evaluated at varying temperatures, pH and light periods to optimize the algal growth for enhanced biodiesel production. After optimization, biodiesel production by Spyrogyra sp. was recorded in real food industry wastewater. The algal biomass increased with increasing level of food industry wastewater and was at maximum with 100% wastewater. Moreover, statistically similar results were found with algal growth on 100% wastewater and also on Bristol's media. The Cladophora sp. produced higher biomass than Spyrogyra sp. while growing on food industry wastewater. The optimal growth of both microalgal strains was observed at temperature 30 °C, pH: 8, light 24 h. Cladophora sp. was further evaluated for biodiesel production while growing on 100% wastewater and found that this strain produced high level of oil and biodiesel. Algae have an ample potential to produce biodiesel from spent wash of food industry. In addition, it is cheaper and presents an environment friendly way to handle food industry wastewater.

  8. Potential use of eucalyptus biodiesel in compressed ignition engine

    Directory of Open Access Journals (Sweden)

    Puneet Verma

    2016-03-01

    Full Text Available The increased population has resulted in extra use of conventional sources of fuels due to which there is risk of extinction of fossil fuels’ resources especially petroleum diesel. Biodiesel is emerging as an excellent alternative choice across the world as a direct replacement for diesel fuel in vehicle engines. Biodiesel offers a great choice. It is mainly derived from vegetable oils, animal fats and algae. Hence in this paper effort has been made to find out feasibility of biodiesel obtained from eucalyptus oil and its impact on diesel engine. Higher viscosity is a major issue while using vegetable oil directly in engine which can be removed by converting it into biodiesel by the process of transesterification. Various fuel properties like calorific value, flash point and cetane value of biodiesel and biodiesel–diesel blends of different proportions were evaluated and found to be comparable with petroleum diesel. The result of investigation shows that Brake Specific Fuel Consumption (BSFC for two different samples of B10 blend of eucalyptus biodiesel is 2.34% and 2.93% lower than that for diesel. Brake Thermal Efficiency (BTE for B10 blends was found to be 0.52% and 0.94% lower than that for diesel. Emission characteristics show that Smoke Opacity improves for both samples, smoke is found to be 64.5% and 62.5% cleaner than that of diesel. Out of all blends B10 was found to be a suitable alternative to conventional diesel fuel to control air pollution without much significant effect on engine performance. On comparing both samples, biodiesel prepared from sample A of eucalyptus oil was found to be superior in all aspects of performance and emission.

  9. Prospects of biodiesel from Jatropha in India: A review

    International Nuclear Information System (INIS)

    Jain, Siddharth; Sharma, M.P.

    2010-01-01

    The increasing industrialization and modernization of the world has to a steep rise for the demand of petroleum products. Economic development in developing countries has led to huge increase in the energy demand. In India, the energy demand is increasing at a rate of 6.5% per annum. The crude oil demand of the country is met by import of about 80%. Thus the energy security has become a key issue for the nation as a whole. Petroleum-based fuels are limited. The finite reserves are highly concentrated in certain regions of the world. Therefore, those countries not having these reserves are facing foreign exchange crises, mainly due to the import of crude oil. Hence it is necessary to look forward for alternative fuels, which can be produced from feedstocks available within the country. Biodiesel, an ecofriendly and renewable fuel substitute for diesel has been getting the attention of researchers/scientists of all over the world. The R and D has indicated that up to B20, there is no need of modification and little work is available related to suitability and sustainability of biodiesel production from Jatropha as non-edible oil sources. In addition, the use of vegetable oil as fuel is less polluting than petroleum fuels. The basic problem with biodiesel is that it is more prone to oxidation resulting in the increase in viscosity of biodiesel with respect to time which in turn leads to piston sticking, gum formation and fuel atomization problems. The report is an attempt to present the prevailing fossil fuel scenario with respect to petroleum diesel, fuel properties of biodiesel resources for biodiesel production, processes for its production, purification, etc. Lastly, an introduction of stability of biodiesel will also be presented. (author)

  10. Quantitative Investigations of Biodiesel Fuel Using Infrared Spectroscopy: An Instrumental Analysis Experiment for Undergraduate Chemistry Students

    Science.gov (United States)

    Ault, Andrew P.; Pomeroy, Robert

    2012-01-01

    Biodiesel has gained attention in recent years as a renewable fuel source due to its reduced greenhouse gas and particulate emissions, and it can be produced within the United States. A laboratory experiment designed for students in an upper-division undergraduate laboratory is described to study biodiesel production and biodiesel mixing with…

  11. Complete utilization of spent coffee grounds to produce biodiesel, bio-oil and biochar

    Science.gov (United States)

    This study presents the complete utilization of spent coffee grounds to produce biodiesel, bio-oil and biochar. Lipids extracted from spent grounds were converted to biodiesel to evaluate neat and blended (B5 and B20) fuel properties against ASTM and EN standards. Although neat biodiesel displayed h...

  12. Utilization of biodiesel waste as a feedstock for the production of ...

    African Journals Online (AJOL)

    use

    2011-12-05

    Dec 5, 2011 ... Key words: Biodiesel, Cupriavidus necator, glycerol, optimization, polyhydroxybutyrate, poly-3-hydroxybutyrate. (PHB). INTRODUCTION. Biodiesel is a renewable energy derived from the reaction of vegetable oils or lipids and alcohol with or without the presence of a catalyst. The advantage of biodiesel is ...

  13. DNA adducts induced by in vitro activation of extracts of diesel and biodiesel exhaust particles

    Science.gov (United States)

    AbstractContext: Biodiesel and biodiesel-blend fuels offer a renewable alternative to petroleum diesel, but few data are available concerning the carcinogenic potential of biodiesel exhausts. Objectives: We compared the formation of covalent DNA adducts by the in vitro metabol...

  14. French bio-diesel demand and promoting measures analysis by 2010

    International Nuclear Information System (INIS)

    Bernard, F.

    2008-02-01

    The researches presented aim at assessing bio-diesel promoting measures under consideration in France by 2010. This assessment is based on a deep study of French bio-diesel demand. The use of a linear model for optimizing the whole French refining industry costs allow us to take into account the physicochemical characteristics of bio-diesel useful for gas oil blending operation. This researches show that bio-diesel can be incorporated up to 27% blend in volume to diesel fuel without major technical problem. A decomposition of the value allotted to the bio-diesel by French refiners according to its physicochemical characteristics shows that energy content is the most disadvantageous characteristics for bio-diesel incorporation and, up to 17%, density become also constraining. However, the low bio-diesel sulphur content could become interesting from now to 2010. On the basis of this bio-diesel demand analysis, we proceed to an external coupling of an agro-industrial model of bio-diesel supply with the French refining model. Thus, we study the impact of the 2010 French bio-diesel consumption objective on agricultural surface need, the competitiveness of the bio-diesel, the reduction of greenhouse gases emissions and the trade balance of the petroleum products. On this basis, we propose a critical analysis of French bio-diesel promoting measures under consideration by 2010. (author)

  15. Aerobic Biodegradation Kinetics And Mineralization Of Six Petrodiesel/Soybean-Biodiesel Blends

    Science.gov (United States)

    The aerobic biodegradation kinetics and mineralization of six petrodiesel/soybean-biodiesel blends (B0, B20, B40, B60, B80, and B100), where B100 is 100% biodiesel, were investigated by acclimated cultures. The fatty acid methyl esters (FAMEs) of biodiesel were found to undergo ...

  16. Anaerobic Biodegradation of Soybean Biodiesel and Diesel Blends under Methanogenic Conditions

    Science.gov (United States)

    Biotransformation of soybean biodiesel and the inhibitory effect of petrodiesel were studied under methanogenic conditions. Biodiesel removal efficiency of more than 95% was achieved in a chemostat with influent biodiesel concentrations up to 2.45 g/L. The kinetics of anaerobic...

  17. Effects of monoacylglycerols on low-temperature viscosity and cold filter plugging point of biodiesel

    Science.gov (United States)

    Biodiesel is composed of mono-alkyl fatty acid esters made from the transesterification of vegetable oil or animal fat with methanol or ethanol. Biodiesel must meet rigorous standard fuel specifications (ASTM D 6751; CEN EN 14214) to be classified as an alternative fuel. Nevertheless, biodiesel that...

  18. 16 CFR Appendix A to Part 306 - Summary of Labeling Requirements for Biodiesel Fuels

    Science.gov (United States)

    2010-01-01

    ... Biodiesel Fuels A Appendix A to Part 306 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER... Part 306—Summary of Labeling Requirements for Biodiesel Fuels (Part 1 of 2) Fuel type Blends of 5 percent or less Blends of more than 5 but not more than 20 percent Header Text Color Biodiesel No label...

  19. Biodiesel From waste cooking oil for heating, lighting, or running diesel engines

    Science.gov (United States)

    Rico O. Cruz

    2009-01-01

    Biodiesel and its byproducts and blends can be used as alternative fuel in diesel engines and for heating, cooking, and lighting. A simple process of biodiesel production can utilize waste cooking oil as the main feedstock to the transesterification and cruzesterification processes. I currently make my own biodiesel for applications related to my nursery and greenhouse...

  20. Pengolahan Biji Mahoni (Swietenia Macrophylla King) Sebagai Bahan Baku Alternatif Biodiesel

    OpenAIRE

    Damayanti, Astrilia; Bariroh, Siti

    2012-01-01

    Peningkatan kebutuhan minyak bumi yang terus menerus akan mengakibatkan kelangkaan bahan bakar minyak. Sumber energi alternatif yang ramah lingkungan, salah satunya adalah biodiesel. Bahan baku potensial untuk memproduksi biodiesel yang tidak bersaing dengan bahan baku pangan contohnya adalah biji mahoni (swietenia macrophylla king). Tahapan yang diperlukan dalam percobaan biodiesel adalah proses pengambilan minyak biji mahoni dengan proses penyangraian, degumming, dan proses transesterifikas...

  1. [FTIR detection of unregulated emissions from a diesel engine with biodiesel fuel].

    Science.gov (United States)

    Tan, Pi-qiang; Hu, Zhi-yuan; Lou, Di-ming

    2012-02-01

    Biodiesel, as one of the most promising alternative fuels, has received more attention because of limited fossil fuels. A comparison of biodiesel and petroleum diesel fuel is discussed as regards engine unregulated exhaust emissions. A diesel fuel, a pure biodiesel fuel, and fuel with 20% V/V biodiesel blend ratio were tested without engine modification The present study examines six typical unregulated emissions by Fourier transform infrared spectroscopy (FTIR) method: formaldehyde (HCHO), acetaldehyde (C2 H4 O), acetone (C3 H6 O), toluene (C7 H8), sulfur dioxide (SO2), and carbon dioxide (CO2). The results show addition of biodiesel fuel increases the formaldehyde emission, and B20 fuel has little change, but the formaldehyde emission of pure biodiesel shows a clear trend of addition. Compared with the pure diesel fuel, the acetaldehyde of B20 fuel has a distinct decrease, and the acetaldehyde emission of pure biodiesel is lower than that of the pure diesel fuel at low and middle engine loads, but higher at high engine load. The acetone emission is very low, and increases for B20 and pure biodiesel fuels as compared to diesel fuel. Compared with the diesel fuel, the toluene and sulfur dioxide values of the engine show a distinct decrease with biodiesel blend ratio increasing. It is clear that the biodiesel could reduce aromatic compounds and emissions of diesel engines. The carbon dioxide emission of pure biodiesel has a little lower value than diesel, showing that the biodiesel benefits control of greenhouse gas.

  2. Combustion, performance and emissions of a diesel power generator fueled with biodiesel-kerosene and biodiesel-kerosene-diesel blends

    International Nuclear Information System (INIS)

    Bayındır, Hasan; Işık, Mehmet Zerrakki; Argunhan, Zeki; Yücel, Halit Lütfü; Aydın, Hüseyin

    2017-01-01

    High percentages of biodiesel blends or neat biodiesel cannot be used in diesel engines due to high density and viscosity, and poor atomization properties that lead to some engine operational problems. Biodiesel was produced from canola oil by transesterification process. Test fuels were prepared by blending 80% of the biodiesel with 20% of kerosene (B80&K20) and 80% of the biodiesel with 10% of kerosene and 10% diesel fuel (B80&K10&D10). Fuels were used in a 4 cylinders diesel engine that was loaded with a generator. Combustion, performance and emission characteristics of the blend fuels and D2 in the diesel engine for certain loads of 3.6, 7.2 and 10.8 kW output power and 1500 rpm constant engine speed were experimented and deeply analyzed. It was found that kerosene contained blends had quite similar combustion characteristics with those of D2. Mass fuel consumption and Bscf were slightly increased for blend fuels. HC emissions slightly increased while NOx emissions considerably reduced for blends. It was resulted that high percentages of biodiesel can be a potential substitute for diesel fuel provided that it is used as blending fuel with certain amounts of kerosene. - Highlights: • Effects of kerosene and diesel addition to biodiesel in a diesel engine were investigated. • B80&K10 and B80&K10&D10 were tested and comparisons have been made with D2. • Similar fuel properties and combustion parameters have been found for all fuels. • Heat release initiated earlier for B80&K10 and B80&K10&D10. • CO and NOx emissions are lowered for B80&K10 and B80&K10&D10.

  3. Assessing the greenhouse gas emissions of Brazilian soybean biodiesel production

    Science.gov (United States)

    You, Xin; Cherubin, Maurício Roberto; Moreira, Cindy Silva; Raucci, Guilherme Silva; Castigioni, Bruno de Almeida; Alves, Priscila Aparecida; Cerri, Domingos Guilherme Pellegrino; Mello, Francisco Fujita de Castro; Cerri, Carlos Clemente

    2017-01-01

    Soybean biodiesel (B100) has been playing an important role in Brazilian energy matrix towards the national bio-based economy. Greenhouse gas (GHG) emissions is the most widely used indicator for assessing the environmental sustainability of biodiesels and received particular attention among decision makers in business and politics, as well as consumers. Former studies have been mainly focused on the GHG emissions from the soybean cultivation, excluding other stages of the biodiesel production. Here, we present a holistic view of the total GHG emissions in four life cycle stages for soybean biodiesel. The aim of this study was to assess the GHG emissions of Brazilian soybean biodiesel production system with an integrated life cycle approach of four stages: agriculture, extraction, production and distribution. Allocation of mass and energy was applied and special attention was paid to the integrated and non-integrated industrial production chain. The results indicated that the largest source of GHG emissions, among four life cycle stages, is the agricultural stage (42–51%) for B100 produced in integrated systems and the production stage (46–52%) for B100 produced in non-integrated systems. Integration of industrial units resulted in significant reduction in life cycle GHG emissions. Without the consideration of LUC and assuming biogenic CO2 emissions is carbon neutral in our study, the calculated life cycle GHG emissions for domestic soybean biodiesel varied from 23.1 to 25.8 gCO2eq. MJ-1 B100 and those for soybean biodiesel exported to EU ranged from 26.5 to 29.2 gCO2eq. MJ-1 B100, which represent reductions by 65% up to 72% (depending on the delivery route) of GHG emissions compared with the EU benchmark for diesel fuel. Our findings from a life cycle perspective contributed to identify the major GHG sources in Brazilian soybean biodiesel production system and they can be used to guide mitigation priority for policy and decision-making. Projected scenarios in

  4. Assessing the greenhouse gas emissions of Brazilian soybean biodiesel production.

    Directory of Open Access Journals (Sweden)

    Carlos Eduardo Pellegrino Cerri

    Full Text Available Soybean biodiesel (B100 has been playing an important role in Brazilian energy matrix towards the national bio-based economy. Greenhouse gas (GHG emissions is the most widely used indicator for assessing the environmental sustainability of biodiesels and received particular attention among decision makers in business and politics, as well as consumers. Former studies have been mainly focused on the GHG emissions from the soybean cultivation, excluding other stages of the biodiesel production. Here, we present a holistic view of the total GHG emissions in four life cycle stages for soybean biodiesel. The aim of this study was to assess the GHG emissions of Brazilian soybean biodiesel production system with an integrated life cycle approach of four stages: agriculture, extraction, production and distribution. Allocation of mass and energy was applied and special attention was paid to the integrated and non-integrated industrial production chain. The results indicated that the largest source of GHG emissions, among four life cycle stages, is the agricultural stage (42-51% for B100 produced in integrated systems and the production stage (46-52% for B100 produced in non-integrated systems. Integration of industrial units resulted in significant reduction in life cycle GHG emissions. Without the consideration of LUC and assuming biogenic CO2 emissions is carbon neutral in our study, the calculated life cycle GHG emissions for domestic soybean biodiesel varied from 23.1 to 25.8 gCO2eq. MJ-1 B100 and those for soybean biodiesel exported to EU ranged from 26.5 to 29.2 gCO2eq. MJ-1 B100, which represent reductions by 65% up to 72% (depending on the delivery route of GHG emissions compared with the EU benchmark for diesel fuel. Our findings from a life cycle perspective contributed to identify the major GHG sources in Brazilian soybean biodiesel production system and they can be used to guide mitigation priority for policy and decision-making. Projected

  5. Assessing the greenhouse gas emissions of Brazilian soybean biodiesel production.

    Science.gov (United States)

    Cerri, Carlos Eduardo Pellegrino; You, Xin; Cherubin, Maurício Roberto; Moreira, Cindy Silva; Raucci, Guilherme Silva; Castigioni, Bruno de Almeida; Alves, Priscila Aparecida; Cerri, Domingos Guilherme Pellegrino; Mello, Francisco Fujita de Castro; Cerri, Carlos Clemente

    2017-01-01

    Soybean biodiesel (B100) has been playing an important role in Brazilian energy matrix towards the national bio-based economy. Greenhouse gas (GHG) emissions is the most widely used indicator for assessing the environmental sustainability of biodiesels and received particular attention among decision makers in business and politics, as well as consumers. Former studies have been mainly focused on the GHG emissions from the soybean cultivation, excluding other stages of the biodiesel production. Here, we present a holistic view of the total GHG emissions in four life cycle stages for soybean biodiesel. The aim of this study was to assess the GHG emissions of Brazilian soybean biodiesel production system with an integrated life cycle approach of four stages: agriculture, extraction, production and distribution. Allocation of mass and energy was applied and special attention was paid to the integrated and non-integrated industrial production chain. The results indicated that the largest source of GHG emissions, among four life cycle stages, is the agricultural stage (42-51%) for B100 produced in integrated systems and the production stage (46-52%) for B100 produced in non-integrated systems. Integration of industrial units resulted in significant reduction in life cycle GHG emissions. Without the consideration of LUC and assuming biogenic CO2 emissions is carbon neutral in our study, the calculated life cycle GHG emissions for domestic soybean biodiesel varied from 23.1 to 25.8 gCO2eq. MJ-1 B100 and those for soybean biodiesel exported to EU ranged from 26.5 to 29.2 gCO2eq. MJ-1 B100, which represent reductions by 65% up to 72% (depending on the delivery route) of GHG emissions compared with the EU benchmark for diesel fuel. Our findings from a life cycle perspective contributed to identify the major GHG sources in Brazilian soybean biodiesel production system and they can be used to guide mitigation priority for policy and decision-making. Projected scenarios in this

  6. Particulate filter behaviour of a Diesel engine fueled with biodiesel

    International Nuclear Information System (INIS)

    Buono, D.; Senatore, A.; Prati, M.V.

    2012-01-01

    Biodiesel is an alternative and renewable fuel made from plant and animal fat or cooked oil through a transesterification process to produce a short chain ester (generally methyl ester). Biodiesel fuels have been worldwide studied in Diesel engines and they were found to be compatible in blends with Diesel fuel to well operate in modern Common Rail engines. Also throughout the world the diffusion of biofuels is being promoted in order to reduce greenhouse gas emissions and the environmental impact of transport, and to increase security of supply. To meet the current exhaust emission regulations, after-treatment devices are necessary; in particular Diesel Particulate Filters (DPFs) are essential to reduce particulate emissions of Diesel engines. A critical requirement for the implementation of DPF on a modern Biodiesel powered engine is the determination of Break-even Temperature (BET) which is defined as the temperature at which particulate deposition on the filter is balanced by particulate oxidation on the filter. To fit within the exhaust temperature range of the exhaust line and to require a minimum of active regeneration during the engine running, the BET needs to occur at sufficiently low temperatures. In this paper, the results of an experimental campaign on a modern, electronic controlled fuel injection Diesel engine are shown. The engine was fuelled either with petroleum ultralow sulphur fuel or with Biodiesel: BET was evaluated for both fuels. Results show that on average, the BET is lower for biodiesel than for diesel fuel. The final goal was to characterize the regeneration process of the DPF device depending on the adopted fuel, taking into account the different combustion process and the different nature of the particulate matter. Overall the results suggest significant benefits for the use of biodiesel in engines equipped with DPFs. - Highlights: ► We compare Diesel Particulate Trap (DPF) performance with Biodiesel and Diesel fuel. ► The Break

  7. Comparative Analysis of Biodiesels from Calabash and Rubber Seeds Oils

    Directory of Open Access Journals (Sweden)

    J.O. Awulu

    2015-07-01

    Full Text Available Physicochemical properties of biodiesel from vegetable oils depend on the inherent properties of the oil-producing seeds. The purpose of this study is to investigate the physicochemical properties of biodiesels extracted from calabash and rubber seeds oils, as well as their combined oil mixtures with a view to ascertaining the most suitable for biodiesel production. Calabash and rubber seeds oils were separately extracted through the use of a mechanical press with periodic addition of water. Biodiesels were produced from each category of the oils by transesterification of the free fatty acid (FFA with alcohol under the influence of a catalyst in batch process. The physicochemical properties of the biodiesels were investigated and comparatively analysed. The results obtained indicated an average of 1.40 wt% FFA for biodiesel produced from the purified calabash oil, which has a specific gravity of 0.920, pH of 5.93, flash point of 116 0C, fire point of 138 0C, cloud point of 70 0C, pour point of -4 0C, moisture content of 0.82 wt% and specific heat capacity of 5301 J/kgK. Conversely, the results obtained for biodiesel produced from the purified rubber oil showed an average of 33.66 wt% FFA, specific gravity of 0.885, pH of 5.51, flash point of 145 0C, fire point of 170 0C, cloud point of 10 0C, pour point of 4 0C, moisture content of 1.30 wt% and specific heat capacity of 9317 J/kgK. However, results obtained for biodiesel produced from the combined oil mixtures indicated an average of 19.77 wt% FFA content, specific gravity of 0.904, API gravity of 25.036, pH value of 5.73, flash point of 157 0C, Fire point of 180 0C, cloud point of 9 0C, pour point of 5 0C, moisture content of 0.93 wt% and specific heat capacity of 6051 J/kgK. Biodiesel produced from calabash seed oil is superior in quality to rubber seed oil, particularly in terms of its low FFA and moisture contents.

  8. Biodiesel production using oil from fish canning industry wastes

    International Nuclear Information System (INIS)

    Costa, J.F.; Almeida, M.F.; Alvim-Ferraz, M.C.M.; Dias, J.M.

    2013-01-01

    Highlights: • A process was established to produce biodiesel from fish canning industry wastes. • Biodiesel production was enabled by an acid esterification pre-treatment. • Optimization studies showed that the best catalyst concentration was 1 wt.% H 2 SO 4 . • There was no advantage when a two-step alkali transesterification was employed. • Waste oil from olive oil bagasse could be used to improve fuel quality. - Abstract: The present study evaluated biodiesel production using oil extracted from fish canning industry wastes, focusing on pre-treatment and reaction conditions. Experimental planning was conducted to evaluate the influence of acid catalyst concentration (1–3 wt.% H 2 SO 4 ) in the esterification pre-treatment and the amount of methanolic solution (60–90 vol.%) used at the beginning of the further two-step alkali transesterification reaction. The use of a raw-material mixture, including waste oil obtained from olive oil bagasse, was also studied. The results from experimental planning showed that catalyst concentration mostly influenced product yield and quality, the best conditions being 1 wt.% catalyst and 60 vol.% of methanolic solution, to obtain a product yield of 73.9 wt.% and a product purity of 75.5 wt.%. Results from a one-step reaction under the selected conditions showed no advantage of performing a two-step alkali process. Although under the best conditions several of the biodiesel quality parameters were in agreement with standard specifications, a great variation was found in the biodiesel acid value, and oxidation stability and methyl ester content did not comply with biodiesel quality standards. Aiming to improve fuel quality, a mixture containing 80% waste olive oil and 20% of waste fish oil was evaluated. Using such mixture, biodiesel purity increased around 15%, being close to the standard requirements (96.5 wt.%), and the oxidation stability was in agreement with the biodiesel quality standard values (⩾6 h), which

  9. Production of Biodiesel from Pinus Roxburghii Oil and its Evaluation

    International Nuclear Information System (INIS)

    Ishfaq, M.; Ahmad, I.; Shakiruliah, M.; Saeed, K.

    2013-01-01

    Biodiesel fuel is an alternative and renewable source of energy. It may help to reduce air pollution and our dependence on fossil fuel for energy. In this study the plant oil was extracted from saw dust of pine tree using methanol as a solvent and acid catalyst (H/sub 2/SO/sub 4/) was used for transesterification. The effect of reaction time, temperature and catalyst ratio was studied, which presented that the high yield of biodiesel is produced by using 9 mL of catalyst for 1 h reaction time. The physicochemical properties such as density, viscosity, heating value, cetane index, flash point, Conradson carbon residue and distillation behavior of the obtained biodiesel were determined. The results showed that the final fatty acid methyl esters (FAME) product meets with the biodiesel quality standards, and ASTM specification D6751-02. The UV-Visible and FT-IR spectroscopic studies was also performed, which revealed that the synthesized biodiesel consists of aliphatic, olifinic and aromatic hydrocarbons along with fatty acids. (author)

  10. Ultrasound Assisted Esterification of Rubber Seed Oil for Biodiesel Production

    Directory of Open Access Journals (Sweden)

    W Widayat

    2012-04-01

    Full Text Available Production of biodiesel is currently shifting from the first to the second generation inwhich the raw materials are mostly from non-edible type oils and fats. Biodiesel production iscommonly conducted under batch operation using mechanical agitation to accelerate masstransfers. The main drawback of oil esterification is the high content of free fatty acids (FFA whichmay reduce the yield of biodiesel and prolong the production time (2-5 hours. Ultrasonificationhas been used in many applications such as component extraction due to its ability to producecavitation under certain frequency. This research is aimed to facilitate ultrasound system forimproving biodiesel production process particularly rubber seed oil. An ultrasound unit was usedunder constant temperature (40oC and frequency of 40 Hz. The result showed that ultrasound canreduces the processing time and increases the biodiesel yield significantly. A model to describecorrelation of yield and its independent variables is yield (Y = 43,4894 – 0,6926 X1 + 1,1807 X2 –7,1042 X3 + 2,6451 X1X2 – 1,6557 X1X3 + 5,7586 X2X3 - 10,5145 X1X2X3, where X1 is mesh sizes, X2ratio oil: methanol and X3 type of catalyst.

  11. Solid Catalysts and theirs Application in Biodiesel Production

    Directory of Open Access Journals (Sweden)

    Ramli Mat

    2012-12-01

    Full Text Available The reduction of oil resources and increasing petroleum price has led to the search for alternative fuel from renewable resources such as biodiesel. Currently biodiesel is produced from vegetable oil using liquid catalysts. Replacement of liquid catalysts with solid catalysts would greatly solve the problems associated with expensive separation methods and corrosion problems, yielding to a cleaner product and greatly decreasing the cost of biodiesel production. In this paper, the development of solid catalysts and its catalytic activity are reviewed. Solid catalysts are able to perform trans-esterification and esterification reactions simultaneously and able to convert low quality oils with high amount of Free Fatty Acids. The parameters that effect the production of biodiesel are discussed in this paper. Copyright © 2012 by BCREC UNDIP. All rights reservedReceived: 6th April 2012, Revised: 24th October 2012, Accepted: 24th October 2012[How to Cite: R. Mat, R.A. Samsudin, M. Mohamed, A. Johari, (2012. Solid Catalysts and Their Application in Biodiesel Production. Bulletin of Chemical Reaction Engineering & Catalysis, 7(2: 142-149. doi:10.9767/bcrec.7.2.3047.142-149] [How to Link / DOI: http://dx.doi.org/10.9767/bcrec.7.2.3047.142-149 ] | View in 

  12. Thermoeconomic Analysis of Biodiesel Production from Used Cooking Oils

    Directory of Open Access Journals (Sweden)

    Emilio Font de Mora

    2015-05-01

    Full Text Available Biodiesel from used cooking oil (UCO is one of the most sustainable solutions to replace conventional fossil fuels in the transport sector. It can achieve greenhouse gas savings up to 88% and at the same time reducing the disposal of a polluting waste. In addition, it does not provoke potential negative impacts that conventional biofuels may eventually cause linked to the use of arable land. For this reason, most policy frameworks favor its consumption. This is the case of the EU policy that double-counters the use of residue and waste use to achieve the renewable energy target in the transport sector. According to different sources, biodiesel produced from UCO could replace around 1.5%–1.8% of the EU-27 diesel consumption. This paper presents an in-depth thermoeconomic analysis of the UCO biodiesel life cycle to understand its cost formation process. It calculates the ExROI value (exergy return on investment and renewability factor, and it demonstrates that thermoeconomics is a useful tool to assess life cycles of renewable energy systems. It also shows that UCO life cycle biodiesel production is more sustainable than biodiesel produced from vegetable oils.

  13. Noncatalytic biodiesel fuel production from croton megalocarpus oil

    Energy Technology Data Exchange (ETDEWEB)

    Kafuku, G.; Mbarawa, M. [Department of Mechanical Engineering, Tshwane University of Technology, Pretoria (South Africa); Tan, K.T.; Lee, K.T. [School of Chemical Engineering, Universiti Sains Malaysia, Engineering Campus, Seri Ampangan, Nibong Tebal, Pulau Pinang (Malaysia)

    2011-11-15

    Biodiesel is currently considered as the most promising substitute for diesel fuel because of its similar properties to diesel. This study presents the use of the supercritical methanol method in the production of biodiesel from Croton megalocarpus oil. The reaction parameters such as methanol-to-oil ratio, reaction temperature and reaction time were varied to obtain the optimal reaction conditions by design of experiment, specifically, response surface methodology based on three-variable central composite design with {alpha}=2. It has been shown that it is possible to achieve methyl ester yields as high as 74.91 % with reaction conditions such as 50:1 methanol-to-oil molar ratio, 330 C reaction temperature and a reaction period of 20 min. However, Croton-based biodiesel did not sustain higher temperatures due to decomposition of polyunsaturated methyl linoleate, which is dominant in biodiesel. Lower yields were observed when higher temperatures were used during the optimization process. The supercritical methanol method showed competitive biodiesel yields when compared with catalytic methods. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. Cultivation of freshwater microalgae in biodiesel wash water.

    Science.gov (United States)

    Sassi, Patrícia Giulianna Petraglia; Calixto, Clediana Dantas; da Silva Santana, Jordana Kaline; Sassi, Roberto; Costa Sassi, Cristiane Francisca; Abrahão, Raphael

    2017-08-01

    Biodiesel wash water is a contaminating industrial effluent that must be treated prior to disposal. The use of this effluent as a low-cost alternative cultivation medium for microalgae could represent a viable supplementary treatment. We cultivated 11 microalgae species with potential use for biodiesel production to assess their growth capacities in biodiesel industrial washing waters. Only Monoraphidium contortum, Ankistrodesmus sp., Chlorococcum sp., and one unidentified Chlorophyceae species grew effectively in that effluent. M. contortum showed the highest growth capacity and had the second highest fatty acid content (267.9 mg g -1 of DW), predominantly producing palmitic (20.9%), 7,10,13-hexadecatrienoic (14%), oleic (16.2%), linoleic (10.5%), and linolenic acids (23.2%). In the second phase of the experiment, the microalgae were cultivated in biodiesel wash water at 75% of its initial concentration as well as in WC (control) medium. After 21 days of cultivation, 25.8 and 7.2% of the effluent nitrate and phosphate were removed, respectively, and the chemical oxygen demand was diminished by 31.2%. These results suggest the possibility of cultivating biodiesel producing microalgae in industrial wash water effluents.

  15. Conversion of lipid from food waste to biodiesel.

    Science.gov (United States)

    Karmee, Sanjib Kumar; Linardi, Darwin; Lee, Jisoo; Lin, Carol Sze Ki

    2015-07-01

    Depletion of fossil fuels and environmental problems are encouraging research on alternative fuels of renewable sources. Biodiesel is a promising alternative fuel to be used as a substitute to the petroleum based diesel fuels. However, the cost of biodiesel production is high and is attributed mainly to the feedstock used which leads to the investigation of low cost feedstocks that are economically feasible. In this paper, we report on the utilization of lipid obtained from food waste as a low-cost feedstock for biodiesel production. Lipid from food waste was transesterified with methanol using base and lipase as catalysts. The maximum biodiesel yield was 100% for the base (KOH) catalyzed transesterification at 1:10M ratio of lipid to methanol in 2h at 60°C. Novozyme-435 yielded a 90% FAME conversion at 40°C and 1:5 lipid to methanol molar ratio in 24h. Lipid obtained from fungal hydrolysis of food waste is found to be a suitable feedstock for biodiesel production. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. Life cycle assessment of palm-derived biodiesel in Taiwan

    KAUST Repository

    Maharjan, Sumit

    2016-10-01

    In Taiwan, due to the limited capacity of waste cooking oil, palm oil has been viewed as the potential low-cost imported feedstock for producing biodiesel, in the way of obtaining oil feedstock in Malaysia and producing biodiesel in Taiwan. This study aims to evaluate the cradle-to-grave life cycle environmental performance of palm biodiesel within two different Asian countries, Malaysia and Taiwan. The phases of the life cycle such as direct land-use-change impact, plantation and milling are investigated based on the Malaysia case and those of refining, and fuel production as well as engine combustion is based on Taiwan case. The greenhouse gas (GHG) emission and energy consumption for the whole life cycle were calculated as −28.29 kg CO2-equiv. and +23.71 MJ/kg of palm-derived biodiesel. We also analyze the impacts of global warming potential (GWP) and the payback time for recovering the GHG emissions when producing and using biodiesel. Various scenarios include (1) clearing rainforest or peat-forest; (2) treating or discharging palm-oil-milling effluent (POME) are further developed to examine the effectiveness of improving the environmental impacts © 2016 Springer-Verlag Berlin Heidelberg

  17. Assessing biodiesel quality parameters for wastewater grown Chlorella sp.

    Science.gov (United States)

    Bagul, Samadhan Yuvraj; K Bharti, Randhir; Dhar, Dolly Wattal

    2017-07-01

    Microalgae are reported as the efficient source of renewable biodiesel which should be able to meet the global demand of transport fuels. Present study is focused on assessment of wastewater grown indigenous microalga Chlorella sp. for fuel quality parameters. This was successfully grown in secondary treated waste water diluted with tap water (25% dilution) in glass house. The microalga showed a dry weight of 0.849 g L -1 with lipid content of 27.1% on dry weight basis on 21st day of incubation. After transesterification, the yield of fatty acid methyl ester was 80.64% with major fatty acids as palmitic, linoleic, oleic and linolenic. The physical parameters predicted from empirical equations in the biodiesel showed cetane number as 56.5, iodine value of 75.5 g I 2 100 g -1 , high heating value 40.1 MJ kg -1 , flash point 135 °C, kinematic viscosity 4.05 mm 2 s -1 with density of 0.86 g cm 3 and cold filter plugging point as 0.7 °C. Fourier transform infra-red (FTIR), 1 H, 13 C NMR spectrum confirmed the chemical nature of biodiesel. The results indicated that the quality of biodiesel was almost as per the criterion of ASTM standards; hence, wastewater grown Chlorella sp. can be used as a promising strain for biodiesel production.

  18. Thermally assisted sensor for conformity assessment of biodiesel production

    International Nuclear Information System (INIS)

    Kawano, M S; Kamikawachi, R C; Fabris, J L; Muller, M

    2015-01-01

    Although biodiesel can be intentionally tampered with, impairing its quality, ineffective production processes may also result in a nonconforming final fuel. For an incomplete transesterification reaction, traces of alcohol (ethanol or methanol) or remaining raw material (vegetable oil or animal fats) may be harmful to consumers, the environment or to engines. Traditional methods for biodiesel assessment are complex, time consuming and expensive, leading to the need for the development of new and more versatile processes for quality control. This work describes a refractometric fibre optic based sensor that is thermally assisted, developed to quantify the remaining methanol or vegetable oil in biodiesel blends. The sensing relies on a long period grating to configure an in-fibre interferometer. A complete analytical routine is demonstrated for the sensor allowing the evaluation of the biodiesel blends without segregation of the components. The results show the sensor can determine the presence of oil or methanol in biodiesel with a concentration ranging from 0% to 10% v/v. The sensor presented a resolution and standard combined uncertainty of 0.013% v/v and 0.62% v/v for biodiesel–oil samples, and 0.007% v/v and 0.22% v/v for biodiesel–methanol samples, respectively. (paper)

  19. Influence of economical variables on a supercritical biodiesel production process

    International Nuclear Information System (INIS)

    Marchetti, J.M.

    2013-01-01

    Highlights: • Biodiesel production from supercritical process. • Economical analysis. • Influence of market variables. - Abstract: Biodiesel has becoming more and more relevant in today’s society and economy due to its environmental advantages such as biodegradability, lower CO and CO 2 emissions as well as less particulate pollutants. In this work the study of market and economic variables is presented and their effects compared when biodiesel is being produced using a supercritical technology. The production process is based on a supercritical technology with no catalyst and no co-solvent. Price for the raw materials, such as price for the alcohol as well as the oil has been studied. Also, selling price for biodiesel as well as glycerin has been analyzed and compared with prices from other biodiesel production technologies. Economic decisions such as percentage of failure in the production process, investment in research and development, and advertisement have been evaluated; also it has been considered the influence of the tax incentives on the global economy of the production process. Small variations on some of the major market variables would produce significant effects over the global economy of the plant, making it non profitable in some cases

  20. Ultrasound Assisted Esterification of Rubber Seed Oil for Biodiesel Production

    Directory of Open Access Journals (Sweden)

    Berkah Fajar Tamtomo Kiono

    2012-02-01

    Full Text Available roduction of biodiesel is currently shifting from the first to the second generation in which the raw materials are mostly from non-edible type oils and fats. Biodiesel production is commonly conducted under batch operation using mechanical agitation to accelerate mass transfers. The main drawback of oil esterification is the high content of free fatty acids (FFA which may reduce the yield of biodiesel and prolong the production time (2-5 hours. Ultrasonification has been used in many applications such as component extraction due to its ability to produce cavitation under certain frequency. This research is aimed to facilitate ultrasound system for improving biodiesel production process particularly rubber seed oil. An ultrasound unit was used under constant temperature (40oC and frequency of 40 Hz. The result showed that ultrasound can reduces the processing time and increases the biodiesel yield significantly. A model to describe correlation of yield and its independent variables is yield (Y = 43,4894 – 0,6926 X1 + 1,1807 X2 – 7,1042 X3 + 2,6451 X1X2 – 1,6557 X1X3 + 5,7586 X2X3 - 10,5145 X1X2X3, where X1 is mesh sizes, X2 ratio oil: methanol and X3 type of catalyst.

  1. Production of Biodiesel from Locally Available Spent Vegetable Oils

    Directory of Open Access Journals (Sweden)

    Mohamed Mostafa Al Naggar

    2017-06-01

    Full Text Available The depletion of fossil fuels prompted considerable research to find alternative fuels. Due its environmental benefits and renewable nature the production of biodiesel has acquired increasing importance with a view to optimizing the production procedure and the sources of feedstock. Millions of liters of waste frying oil are produced from local restaurants and houses every year, most are discarded into sewage systems causing damage to the networks.  This study is intended to consider aspects related to the feasibility of the production of biodiesel from waste frying oils which will solve the problem of waste frying oil pollution and reduce the cost of biodiesel production.This research studies the conversion of locally available spent vegetable oils of different origins and with different chemical compositions into an environmentally friendly fuel. The biodiesel production requirements by base catalyzed trans-esterification process for the different feed stocks are determined according to the measured physical properties. The quality of the produced biodiesel is compared to petro diesel in terms of established standard specifications.

  2. An optimal U.S. biodiesel fuel subsidy

    International Nuclear Information System (INIS)

    Wu Huiting; Colson, Gregory; Escalante, Cesar; Wetzstein, Michael

    2012-01-01

    Enhanced environmental quality, fuel security, and economic development, along with reduced prices of blended diesel, are often used as justifications for a U.S. federal excise tax exemption on biodiesel fuels. However, the possible effect of increased overall consumption of fuel in response to lower total prices, mitigating the environmental and fuel security benefits, are generally not considered. Taking this price response into account, the optimal U.S biodiesel subsidy is derived. Estimated values of the optimal subsidy are close to the recently expired subsidy, revealing the subsidy's environmental and security benefits. However, further positive environmental and security benefits from the biodiesel tax-exemption subsidy may be obtained if the subsidy is combined with a federal excise tax on petroleum diesel. - Highlights: ► Taking price response into account, the optimal theoretical U.S biodiesel subsidy is derived. ► Estimated values of the optimal subsidy are close to the recently expired subsidy, revealing the subsidy's environmental and security benefits. ► Further positive environmental and security benefits from the biodiesel tax-exemption subsidy may be obtained if the subsidy is combined with a federal excise tax on petroleum diesel.

  3. Emulsions of crude glycerin from biodiesel processing with fuel oil for industrial heating.

    Science.gov (United States)

    Mize, Hannah E; Lucio, Anthony J; Fhaner, Cassie J; Pratama, Fredy S; Robbins, Lanny A; Karpovich, David S

    2013-02-13

    There is considerable interest in using crude glycerin from biodiesel production as a heating fuel. In this work crude glycerin was emulsified into fuel oil to address difficulties with ignition and sustained combustion. Emulsions were prepared with several grades of glycerin and two grades of fuel oil using direct and phase inversion emulsification. Our findings reveal unique surfactant requirements for emulsifying glycerin into oil; these depend on the levels of several contaminants, including water, ash, and components in MONG (matter organic non-glycerin). A higher hydrophile-lipophile balance was required for a stable emulsion of crude glycerin in fuel oil compared to water in fuel oil. The high concentration of salts from biodiesel catalysts generally hindered emulsion stability. Geometric close-packing of micelles was carefully balanced to mechanically stabilize emulsions while also enabling low viscosity for pumping and fuel injection. Phase inversion emulsification produced more stable emulsions than direct emulsification. Emulsions were tested successfully as fuel for a waste oil burner.

  4. A Comprehensive Review of Effect of Biodiesel Additives on Properties, Performance, and Emission

    Science.gov (United States)

    Madiwale, S.; Karthikeyan, A.; Bhojwani, V.

    2017-05-01

    Objectives:- To presents the literature review on effect of biodiesel additives on properties, performance and on emission. Method:-In the current paper reviews are taken from previous years paper which necessitates the need of addition of additives in the blends of biodiesel and studied the its effect on properties, performance and emissions. Emissions from the diesel powered vehicles mostly damaged the earth’s environment and also increased the overall earth’s temperature. This attracts the need of alternative fuels in the field of transportation sector. Past inventions and research showed that Biodiesel can be used as an alternative fuel for the diesel engine. Biodiesel have good combustion characteristics because of their long chain hydrocarbon structure. However biodiesel possesses few disadvantages such as lower heating value, higher flow ability, much high density and not able to flow at low temperature. Higher rate of fuel consumption is identified and higher level of NOx emissions when biodiesel used in an engine as an alternative fuels. Findings:-Different additives such as antioxidants, improvers for cetane number, cold flow properties improver, etc were investigated by the many researcher and scientists and added in the different feedstock of biodiesel or blends of biodiesel with diesel in different proportions. Directly or indirectly fuel additives can improve the reduction in the emissions, improve the fuel economy, and reduce the dependency of the one’s nation on other. Performances of biodiesel vehicles were drastically improved because of additioninthe blends of biodiesel with diesel fuel in specific percentages to meet the international emission standards. Addition of additives in the biodiesel or in the blends of biodiesel basically changes the high temperature and low temperature flow properties of blends of biodiesel. Current paper finds and compares properties of different additives and its effect on blends of biodiesel properties

  5. Biodiesel Production Process Optimization from Sugar Apple Seed Oil (Annona squamosa and Its Characterization

    Directory of Open Access Journals (Sweden)

    Siddalingappa R. Hotti

    2015-01-01

    Full Text Available This paper presents the production of biodiesel from nonedible, renewable sugar apple seed oil and its characterization. The studies were carried out on transesterification of oil with methanol and sodium hydroxide as catalyst for the production of biodiesel. The process parameters such as catalyst concentration, reaction time, and reaction temperature were optimized for the production of sugar apple biodiesel (SABD. The biodiesel yield of 95.15% was noticed at optimal process parameters. The fuel properties of biodiesel produced were found to be close to that of diesel fuel and also they meet the specifications of ASTM standards.

  6. Biodiesel-derived crude glycerol bioconversion to animal feed: a sustainable option for a biodiesel refinery.

    Science.gov (United States)

    Nitayavardhana, Saoharit; Khanal, Samir Kumar

    2011-05-01

    This study examined the potential of producing an edible fungus, Rhizopus microsporus var. oligosporus, on biodiesel-derived crude glycerol. Prolific fungal growth was observed with a fungal biomass yield of 0.83 ± 0.02 (g biomass increase/ginitial biomass) under optimal cultivation conditions (e.g. nonsterile crude glycerol at a concentration of 75% (w/v) with nutrient supplementation and without pH control). The potential of utilizing front-end processed banagrass (Pennisetum purpureum) juice as a source of nutrients for crude glycerol fermentation was evaluated with a 2.3-fold improvement in the fungal biomass yield. The glycerol-derived fungal biomass showed high amounts of threonine, one of the main limiting amino acids in non-ruminant feeds. An inexpensive fungal protein has the potential to reduce meat product prices by lowering the production costs of animal feeds. The application of fungal technology thus provides a unique sustainable option for biodiesel refineries by providing an additional source of revenue from fungal products. Copyright © 2011 Elsevier Ltd. All rights reserved.

  7. A Pathway to Energy and Food Security with Biodiesel

    Directory of Open Access Journals (Sweden)

    Maria Amelia Dias

    2016-09-01

    Full Text Available The simultaneous rise in commodity prices and the global production of biofuels, between 2007 and 2008, strengthened discussions, which persist currently, about the competition of land use between biofuel production and food production. The objective of this paper is to compare and evaluate the arguments from both sides. The methodology used was an analysis of the relevant and comprehensive reports and manuscripts on the topic, comparing them to the available data from international organizations and agencies. Biodiesel received special attention in this analysis. The conclusion is that hunger and poverty problems are due to structural and historical roots and they do not have a cause-effect relationship with biodiesel production. In fact, the production of biodiesel, under specific regulatory and production conditions, can be a driver of economic development improving energy security and promoting social inclusion in poor countries, which still have land available for agriculture. 

  8. Biodiesel production from microalgae oil catalyzed by a recombinant lipase.

    Science.gov (United States)

    Huang, Jinjin; Xia, Ji; Jiang, Wei; Li, Ying; Li, Jilun

    2015-03-01

    A recombinant Rhizomucor miehei lipase was constructed and expressed in Pichia pastoris. The target enzyme was termed Lipase GH2 and it can be used as a free enzyme for catalytic conversion of microalgae oil mixed with methanol or ethanol for biodiesel production in an n-hexane solvent system. Conversion rates of two major types of biodiesel, fatty acid methyl ester (FAME) and fatty acid ethyl ester (FAEE), reached maximal values (>90%) after 24h. The process of FAME production is generally more simple and economical than that of FAEE production, even though the two processes show similar conversion rates. In spite of the damaging effect of ethanol on enzyme activity, we successfully obtained ethyl ester by the enzymatic method. Our findings indicate that Lipase GH2 is a useful catalyst for conversion of microalgae oil to FAME or FAEE, and this system provides efficiency and reduced costs in biodiesel production. Copyright © 2014 Elsevier Ltd. All rights reserved.

  9. Ultrasonic enhancement of lipase-catalysed transesterification for biodiesel synthesis.

    Science.gov (United States)

    Bhangu, Sukhvir Kaur; Gupta, Shweta; Ashokkumar, Muthupandian

    2017-01-01

    The production of biodiesel was carried out from canola oil and methanol catalysed by lipase from Candida rugosa under different ultrasonic experimental conditions using horn (20kHz) and plate (22, 44, 98 and 300kHz) transducers. The effects of experimental conditions such as horn tip diameter, ultrasonic power, ultrasonic frequency and enzyme concentrations on biodiesel yield were investigated. The results showed that the application of ultrasound decreased the reaction time from 22-24h to 1.5h with the use of 3.5cm ultrasonic horn, an applied power of 40W, methanol to oil molar ratio of 5:1 and enzyme concentration of 0.23wt/wt% of oil. Low intensity ultrasound is efficient and a promising tool for the enzyme catalysed biodiesel synthesis as higher intensities tend to inactivate the enzyme and reduce its efficiency. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. Biodiesel as a lubricity additive for ultra low sulfur diesel

    Directory of Open Access Journals (Sweden)

    Subongkoj Topaiboul1 and 2,*

    2010-05-01

    Full Text Available With the worldwide trend to reduce emission from diesel engines, ultra low sulfur diesel has been introduced with thesulfur concentration of less than 10 ppm. Unfortunately, the desulfurization process inevitably reduces the lubricity of dieselfuel significantly. Alternatively, biodiesel, with almost zero sulfur content, has been added to enhance lubricity in an ultralow sulfur diesel. This work has evaluated the effectiveness of the biodiesel amount, sourced from palm and jatropha oil,and origin in ultra low sulfur diesel locally available in the market. Wear scar from a high-frequency reciprocating rig isbenchmarked to the standard value (460 m of diesel fuel lubricity. It was found that very small amount (less than 1% ofbiodiesel from either source significantly improves the lubricity in ultra low sulfur diesel, and the biodiesel from jatropha oilis a superior lubricity enhancer.

  11. Production of Biodiesel from Shea Butter Oil using Homogeneous Catalysts

    Directory of Open Access Journals (Sweden)

    Jude EJEH

    2014-02-01

    Full Text Available An investigation into the production of biodiesel from shea butter oil using homogenous catalyst was carried out. The properties of the oil obtained were first determined, having an FFA value of 2.279 amongst other properties. Thus, the direct base-catalysis method was used, with potassium hydroxide as the catalyst. In a 1 hour batch run, biodiesel was produced with a conversion of 92%, FAME content of 97.1%, cetane number of 46.84 and kinematic viscosity of 4.30mm2/s, conforming to ASTM D6751 and EN 14214 international standards. As such, it was established that shea butter biodiesel could be produced by the direct base catalysis, over a shorter time with low cost chemicals.

  12. An Experimental Investigation of Karanja Biodiesel Production in Sarawak, Malaysia

    Directory of Open Access Journals (Sweden)

    Dewi Harreh

    2018-01-01

    Full Text Available The application of nonedible feedstock for the production of biodiesel has become an area of research interest among clean energy experts in the past few years. This research is aimed at the utilization of Pongamia pinnata (karanja, a nonedible feedstock from the state of Sarawak, Malaysia, to produce biodiesel to be known as crude karanja oil (CKO. A one-step transesterification process utilizing 7 : 1–10 : 1 wt% methanol (CH3OH and 0.5–1.2 wt% sodium hydroxide (NaOH at 65°C for 1.5 hrs has been used for the biodiesel production yielding 84% conversion. The physiochemical properties of the CKO produced revealed that it conforms with EN14214 standards for brake power (BP, brake specific fuel consumption (BSFC, and brake thermal efficiency (BTE as they are all noted be optimal at B40.

  13. Biodiesel obtained from soapstock originated in a refining oil industry

    International Nuclear Information System (INIS)

    Tobio Pérez, Indira; Díaz Domínguez, Yosvany; Piloto-Rodríguez, Ramón

    2017-01-01

    In the vegetable oil chemical refining process is obtained a by-product commonly named as soapstock, due to its physical and aspect properties. The soapstock free fatty acid content can reach to 50%. The present work shows a survey of researches focused on biodiesel obtaining from this by-product. The biodiesel is obtained following different routes and catalyzers features. A variety of reports shown the effectivity of the use of this by-product derived from vegetable oil refining industry to produce biodiesel. Several studies are addressed to the acid oil recovering involving processes without soapstock acidulation, with the aim of lowering costs and finding more attractive yields closing to the concept of zero wastes. (author)

  14. Brazilian Biodiesel Policy: Social and environmental considerations of sustainability

    International Nuclear Information System (INIS)

    Garcez, Catherine Aliana Gucciardi; Vianna, Joao Nildo de Souza

    2009-01-01

    The objective of this article is to analyze the Brazilian Biodiesel Policy (PNPB) and to identify the social and environmental aspects of sustainability that are present or absent within it. Biofuels, namely alcohol and biodiesel, have been increasing in popularity on a global scale due to their potential as alternative and renewable energy sources. Brazil, a vast country blessed with abundant natural resources and agricultural land, has emerged as a global leader in the production of biofuels. This article includes a brief analysis of the concept of sustainable development, which served as a basis to evaluate the Policy documents. Although PNPB's implementation, which began in 2004, is still within its initial stage, it was possible to identify and elaborate on the environmental and social aspects of the Policy, namely: the social inclusion of family farmers; regional development; food security; influencing the carbon and energy balance of biodiesel; promoting sustainable agricultural practices and a diversity of feedstock. (author)

  15. Experimental viscosity measurements of biodiesels at high pressure

    Directory of Open Access Journals (Sweden)

    Schaschke C.J.

    2016-01-01

    Full Text Available The viscosity of biodiesels of soybean and rapeseed biodiesels blended with mineral diesel fuel were measured at pressures of up to 200 MPa. Using a falling sinker-type viscometer reproducible viscosity data were obtained based on the time taken for a sinker to descend a fixed distance down an enclosed tube under the influence of gravity. Measurements were taken using pressures which correspond to those of interest in automotive common rail diesel engines, and at temperatures of between 25ºC and 80ºC. In all cases, the viscosity of the biodiesel blends were found to increase exponentially for which the blends were noted as being more viscous than pure mineral fuels. A pressure-freezing effect was not observed for the blends.

  16. Sustainable and Intensified Design of a Biodiesel Production Process

    DEFF Research Database (Denmark)

    Mansouri, Seyed Soheil; Ismail, Muhammad I.; Babi, Deenesh Kavi

    impact and maximum profitability is needed. In this work a computer-aided framework for process synthesis and process intensification is applied for sustainable production of biodiesel from pure/waste palm oil as the feedstock. This approach examines several biodiesel processing routes that were...... of economic and environmental sustainability was identified. For the case of biodiesel production, the intensified process alternative turned out to be the most economical and more sustainable than other alternatives. The computer-aided methods and tools used in this work are: SustainPro (method and tool......The growing concerns about the global warming and greenhouse gas emissions (GHG) have led to an increase in the interest to produce fuel from biomass and from the fact that such fuels can relieve the reliance on imported oil and price. To this end, numerous production facilities are being set up...

  17. From Fed-batch to Continuous Enzymatic Biodiesel Production

    DEFF Research Database (Denmark)

    Price, Jason Anthony; Nordblad, Mathias; Woodley, John M.

    2015-01-01

    In this this paper, we use mechanistic modelling to guide the development of acontinuous enzymatic process that is performed as a fed-batch operation. In this workwe use the enzymatic biodiesel process as a case study. A mechanistic model developedin our previous work was used to determine...... measured components (triglycerides, diglycerides, monoglycerides, free fatty acid and fatty acid methyl esters(biodiesel)) much better than using fed-batch data alone given the smaller residuals. We also observe a reduction in the correlation between the parameters.The model was then used to predict that 5...... reactors are required (with a combined residence time of 30 hours) to reach a final biodiesel concentration within 2 % of the95.6 mass % achieved in a fed-batch operation, for 24 hours....

  18. Biodiesel Production by Reactive Flash: A Numerical Simulation

    Directory of Open Access Journals (Sweden)

    Alejandro Regalado-Méndez

    2016-01-01

    Full Text Available Reactive flash (RF in biodiesel production has been studied in order to investigate steady-state multiplicities, singularities, and effect of biodiesel quality when the RF system approaches to bubble point. The RF was modeled by an index-2 system of differential algebraic equations, the vapor split (ϕ was computed by modified Rachford-Rice equation and modified Raoult’s law computed bubble point, and the continuation analysis was tracked on MATCONT. Results of this study show the existence of turning points, leading to a unique bubble point manifold, (xBiodiesel,T=(0.46,478.41 K, which is a globally stable flashing operation. Also, the results of the simulation in MATLAB® of the dynamic behavior of the RF show that conversion of triglycerides reaches 97% for a residence time of 5.8 minutes and a methanol to triglyceride molar flow ratio of 5 : 1.

  19. Toward solar biodiesel production from CO2 using engineered cyanobacteria.

    Science.gov (United States)

    Woo, Han Min; Lee, Hyun Jeong

    2017-05-01

    Metabolic engineering of cyanobacteria has received attention as a sustainable strategy to convert carbon dioxide to various biochemicals including fatty acid-derived biodiesel. Recently, Synechococcus elongatus PCC 7942, a model cyanobacterium, has been engineered to convert CO2 to fatty acid ethyl esters (FAEEs) as biodiesel. Modular pathway has been constructed for FAEE production. Several metabolic engineering strategies were discussed to improve the production levels of FAEEs, including host engineering by improving CO2 fixation rate and photosynthetic efficiency. In addition, protein engineering of key enzyme in S. elongatus PCC 7942 was implemented to address issues on FAEE secretions toward sustainable FAEE production from CO2. Finally, advanced metabolic engineering will promote developing biosolar cell factories to convert CO2 to feasible amount of FAEEs toward solar biodiesel. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  20. Biodegradation of diesel/biodiesel blends in saturated sand microcosms

    DEFF Research Database (Denmark)

    Lisiecki, Piotr; Chrzanowski, Łukasz; Szulc, Alicja

    2014-01-01

    is commercial biodiesel blend) augmented with a bacterial consortium of petroleum degraders. The biodegradation kinetics for blends were evaluated based on measuring the amount of emitted CO2 after 578 days. Subsequently, the residual aromatic and aliphatic fractions were separated and determined by employing......The aim of the study was to evaluate the biodegradation extent of both aromatic and aliphatic hydrocarbon fractions in saturated sandy microcosm spiked with diesel/biodiesel blends (D, B10, B20, B30, B40, B50, B60, B70, B80, B90 and B100, where D is commercial petroleum diesel fuel and B...... GC-FID and GC _ GC–TOF-MS. Additionally, the influence of biodiesel-amendment on the community dynamics was assessed based on the results of real-time PCR analyzes. Our results suggest that the biodegradation extents of both aliphatic and aromatic hydrocarbon were uninfluenced by the addition...

  1. Lipase-catalyzed biodiesel synthesis with different acyl acceptors

    Directory of Open Access Journals (Sweden)

    Ognjanović Nevena D.

    2008-01-01

    Full Text Available Biodiesel is an alternative fuel for diesel engine that is environmentally acceptable. Conventionally, biodiesel is produced by transesterification of triglycerides and short alcohols in the presence of an acid or an alkaline catalyst. There are several problems associated with this kind of production that can be resolved by using lipase as the biocatalyst. The aim of the present work was to investigate novel acyl acceptors for biodiesel production. 2-Propanol and n-butanol have a less negative effect on lipase stability, and they also improve low temperature properties of the fuel. However, excess alcohol leads to inactivation of the enzyme, and glycerol, a major byproduct, can block the immobilized enzyme, resulting in low enzymatic activity. This problem was solved by using methyl acetate as acyl acceptor. Triacetylglycerol is produced instead of glycerol, and it has no negative effect on the activity of the lipase.

  2. Bio-diesel fuels production: Feasibility studies

    International Nuclear Information System (INIS)

    Tabasso, L.

    1993-01-01

    This paper reviews the efforts being made by Italy's national government and private industry to develop diesel engine fuels derived from vegetable oils, in particular, sunflower seed oil. These fuels are being promoted in Italy from the environmental protection stand-point in that they don't contain any sulfur, the main cause of acid rain, and from the agricultural stand-point in that they provide Italian farmers, whose food crop production capacity is limited due to European Communities agreements, with the opportunity to use their set-aside land for the production of energy crops. This paper provides brief notes on the key performance characteristics of bio-diesel fuels, whose application doesn't require any modifications to diesel engines, apart from minor adjustments to the air/fuel mix regulating system, and assesses commercialization prospects. Brief mention is made of the problems being encountered by the Government in the establishing fair bio-fuel production tax rebates which are compatible with the marketing practices of the petroleum industry. One of the strategies being considered is to use the bio-fuels as additives to be mixed with conventional fuel oils so as to derive a fuel which meets the new European air pollution standards

  3. Biodiesel production by enzyme-catalyzed transesterification

    Directory of Open Access Journals (Sweden)

    Stamenković Olivera S.

    2005-01-01

    Full Text Available The principles and kinetics of biodiesel production from vegetable oils using lipase-catalyzed transesterification are reviewed. The most important operating factors affecting the reaction and the yield of alkyl esters, such as: the type and form of lipase, the type of alcohol, the presence of organic solvents, the content of water in the oil, temperature and the presence of glycerol are discussed. In order to estimate the prospects of lipase-catalyzed transesterification for industrial application, the factors which influence the kinetics of chemically-catalysed transesterification are also considered. The advantages of lipase-catalyzed transesterification compared to the chemically-catalysed reaction, are pointed out. The cost of down-processing and ecological problems are significantly reduced by applying lipases. It was also emphasized that lipase-catalysed transesterification should be greatly improved in order to make it commercially applicable. The further optimization of lipase-catalyzed transesterification should include studies on the development of new reactor systems with immobilized biocatalysts and the addition of alcohol in several portions, and the use of extra cellular lipases tolerant to organic solvents, intracellular lipases (i.e. whole microbial cells and genetically-modified microorganisms ("intelligent" yeasts.

  4. Characterization of Palm Oil as Biodiesel

    Science.gov (United States)

    Gorey, Neeraj; Ghosh, Shankha; Srivastava, Priyank; Kumar, Vivek

    2017-08-01

    The various sources of energy from which mechanical energy is obtained are non-renewable and are thus considered to be unsustainable. These sources include the various fossil fuels like the petroleum, coal and the natural gas. The burning of fossil fuels led to the production of the greenhouse gases increasing the levels of CO2 in the atmosphere. The adverse effects are the global warming and the ozone layer depletion. In a nation like India, where consumable oils are still transported in, it is advantageous to investigate the likelihood of utilising such non-palatable oils as a part of CI motors which are not by and by used as cooking oil. Palm oil (otherwise called dendê oil, from Portuguese) is a consumable vegetable oil got from the monocarp (ruddy mash) of the product of the oil palms. The major objective is to provide a cheap and effective alternative to diesel. This paper is an exploration of the capability of the palm oil as a practical, modest and effective hotspot for the generation of biodiesel. the paper is based on the characterisation of palm oil compare to diesel.

  5. Fuel properties of biodiesel from vegetable oils and oil mixtures. Influence of methyl esters distribution

    International Nuclear Information System (INIS)

    Martínez, G.; Sánchez, N.; Encinar, J.M.; González, J.F.

    2014-01-01

    In this work, the quality of biodiesel produced by basic transesterification from several vegetable oils (soybean, rapeseed, sunflower, high oleic sunflower, Cynara Cardunculus L., Brassica Carinata and Jatropha Curca) cultivated in Extremadura has been studied in detail. The influence of raw material composition on properties such as density, viscosity, cetane number, higher heating value, iodine and saponification values and cold filter plugging point has been verified. Other biodiesel properties such as acid value, water content and flash and combustion points were more dependent on characteristics of production process. Biodiesel produced by rapeseed, sunflower and high oleic sunflower oils transesterification have been biofuels with better properties according to Norm EN 14214. Finally, it has been tested that it is possible to use oils mixtures in biodiesel production in order to improve the biodiesel quality. In addition, with the same process conditions and knowing properties of biodiesel from pure oils; for biodiesel from oils mixtures, its methyl esters content, and therefore properties dependent this content can be predicted from a simple mathematical equation proposed in this work. - Highlights: • Biodiesel quality produced by basic transesterification from vegetable oils. • We examine influences of methyl esters distribution on biodiesel properties. • Biofuels from soybean, sunflower and rapeseed oils were with better properties. • Oils mixtures improve biodiesel quality to fulfill Norm EN 14214. • An equation to predict properties of biodiesel from oil mixtures is proposed

  6. Biodiesel for Brazilian development: current situation and challenges for a sustainable future; Biodiesel para o desenvolvimento brasileiro: situacao atual e desafios para um futuro sustentavel

    Energy Technology Data Exchange (ETDEWEB)

    Bartsch, Aleksandra Sliwowska; Antunes, Adelaide Maria de Souza [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Quimica

    2008-07-01

    This article aims at analyzing the state of art and trends of biodiesel in Brazil, with resort to the Industry Strategic Map, a tool developed by National Industry Federation (CNI). The situation of biodiesel will be analyzed considering : Bases for Development, Processes and Activities, Market and Results for Country. At the beginning is presented the evolution of biodiesel in Brazil e are explained the construction of the Strategic Map by CNI. (author)

  7. Production of Biodiesel from Vietnamese Waste Coffee Beans: Biofuel Yield, Saturation and Stability are All Elevated Compared with Conventional Coffee Biodiesel

    OpenAIRE

    Jenkins, Rhodri; Ellis, Emrys H.; Lewis, Emily J.; Paterson, Michael; Le, Chien; Ting, Valeska; Chuck, Christopher

    2017-01-01

    The suitability of biodiesel produced from spent Vietnamese coffee was examined. Previous work shows that the geographical origin of coffee beans has little effect on the composition and physical properties of the biodiesel produced Jenkins et al. [1]. Vietnamese coffee, however, is roasted in a range of fats and oils for flavour enhancement and therefore has a unique fatty acid profile. The oil yield and biodiesel properties of three Vietnamese coffees were assessed and compared to a coffee ...

  8. Tinjauan Penilaian Siklus Hidup Bahan Bakar Biodiesel di Indonesia

    Directory of Open Access Journals (Sweden)

    Kiman Siregar

    2014-10-01

    Review of Life Cycle Assesment of Biodiesel in Indonesia Abstract. Currently, environmental consideration becomes the most important issue in biodiesel production. Eventhough source of energy is considered as carbon neutral, the production path may release various environmentally hazardous gasses. European and American countries claim that production of biodiesel from palm oil contributes carbon emission to the atmosphere along its production path. Furthermore, US EPA-NODA and EU RED stated that palm oil based biodiesel can only reduce emission of GWP by 17 % and 19 % compared to fossil-fuel based. Considering on the minimum requirement is 20 % for US and 35 % for EU, CPO from Indonesia experiences difficulties to enter the global market. Scientific approach should be undertaken by Indonesia to address this issue. Summary of the literature mentions that the sustainability of biodiesel from palm oil is better than Jatropha curcas, compared to other sources of raw materials, such as rapeseed. Summary of the literature mentions that the value of carbon that can be absorbed by primary forest is higher than secondary forest and palm oil plantation. This is the reason why world claims Indonesia on global warming issues although further research is still needed based on the latest data. From the real condition in Indonesia, in which GHG value before stable productivity is 2 575.47 kg-CO2eq./ton-Biodiesel fuel(BDF for oil palm and 3 057.74 kg-CO2eq./ton-BDF for Jatropha curcas. When the productivity has reached stability, the GHG value is  1 511.96 kg-CO2eq./ton-BDF for oil palm and 380.52 kg-CO2eq./ton-BDF for Jatropha curcas. If we compared to diesel fuel, CO2eq. emission is reduced up to 49.27 % and 88.45 % for BDF-CPO and BDF-CJCO, respectively.

  9. Supercritical biodiesel production and power cogeneration: technical and economic feasibilities.

    Science.gov (United States)

    Deshpande, A; Anitescu, G; Rice, P A; Tavlarides, L L

    2010-03-01

    An integrated supercritical fluid technology with power cogeneration to produce biodiesel fuels, with no need for the costly separations involved with the conventional technology, is proposed, documented for technical and economic feasibility, and preliminarily designed. The core of the integrated system consists of the transesterification of various triglyceride sources (e.g., vegetable oils and animal fats) with supercritical methanol/ethanol. Part of the reaction products can be combusted by a diesel power generator integrated in the system which, in turn, provides the power needed to pressurize the system and the heat of the exhaust gases necessary in the transesterification step. The latter energy demand can also be satisfied by a fired heater, especially for higher plant capacities. Different versions of this system can be implemented based on the main target of the technology: biodiesel production or diesel engine applications, including power generation. The process options considered for biodiesel fuel production estimate break-even processing costs of biodiesel as low as $0.26/gal ($0.07/L) with a diesel power generator and $0.35/gal ($0.09/L) with a fired heater for a plant capacity of 15,000 gal/day (56,775 L/day). Both are significantly lower than the current processing costs of approximately $0.51/gal ($0.13/L) of biodiesel produced by conventional catalytic methods. A retail cost of biodiesel produced by the proposed method is likely to be competitive with the prices of diesel fuels. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

  10. Castor oil biodiesel and its blends as alternative fuel

    International Nuclear Information System (INIS)

    Berman, Paula; Nizri, Shahar; Wiesman, Zeev

    2011-01-01

    Intensive production and commercialization of biodiesel from edible-grade sources have raised some critical environmental concerns. In order to mitigate these environmental consequences, alternative oilseeds are being investigated as biodiesel feedstocks. Castor (Ricinus communis L.) is one of the most promising non-edible oil crops, due to its high annual seed production and yield, and since it can be grown on marginal land and in semi-arid climate. Still, few studies are available regarding its fuel-related properties in its pure form or as a blend with petrodiesel, many of which are due to its extremely high content of ricinoleic acid. In this study, the specifications in ASTM D6751 and D7467 which are related to the fatty acid composition of pure castor methyl esters (B100) and its blend with petrodiesel in a 10% vol ratio (B10) were investigated. Kinematic viscosity and distillation temperature of B100 (15.17 mm 2 s -1 and 398.7 o C respectively) were the only two properties which did not meet the appropriate standard limits. In contrast, B10 met all the specifications. Still, ASTM D7467 requires that the pure biodiesel meets the requirements of ASTM D6751. This can limit the use of a wide range of feedstocks, including castor, as alternative fuel, especially due to the fact that in practice vehicles normally use low level blends of biodiesel and petrodiesel. These issues are discussed in depth in the present study. -- Highlights: → CaME can be used as a biodiesel alternative feedstock when blended in petrodiesel. → Due to the high levels of ricinoleic acid maximum blending level is limited to 10%. → Today, CaME blends are not a viable alternative feedstock. → ASTM D7467 requires that pure biodiesel must meet all the appropriate limits.

  11. Technical aspects of production and analysis of biodiesel from used cooking oil. A review

    Energy Technology Data Exchange (ETDEWEB)

    Enweremadu, C.C.; Mbarawa, M.M. [Department of Mechanical Engineering, Tshwane University of Technology, Private Bag X680, Pretoria 001 (South Africa)

    2009-12-15

    The increasing awareness of the depletion of fossil fuel resources and the environmental benefits of biodiesel fuel has made it more attractive in recent times. The cost of biodiesel, however, is the major hurdle to its commercialization in comparison to petroleum-based diesel fuel. The high cost is primarily due to the raw material, mostly neat vegetable oil. Used cooking oil is one of the economical sources for biodiesel production. However, the products formed during frying, can affect the transesterification reaction and the biodiesel properties. This paper attempts to review various technological methods of biodiesel production from used cooking oil. The analytical methods for high quality biodiesel fuel from used cooking oil like GC, TLC, HPLC, GPC and TGA have also been summarized in this paper. In addition, the specifications provided by different countries are presented. The fuel properties of biodiesel fuel from used cooking oil were also reviewed and compared with those of conventional diesel fuel. (author)

  12. Biodiesel production from various feedstocks and their effects on the fuel properties.

    Science.gov (United States)

    Canakci, M; Sanli, H

    2008-05-01

    Biodiesel, which is a new, renewable and biological origin alternative diesel fuel, has been receiving more attention all over the world due to the energy needs and environmental consciousness. Biodiesel is usually produced from food-grade vegetable oils using transesterification process. Using food-grade vegetable oils is not economically feasible since they are more expensive than diesel fuel. Therefore, it is said that the main obstacle for commercialization of biodiesel is its high cost. Waste cooking oils, restaurant greases, soapstocks and animal fats are potential feedstocks for biodiesel production to lower the cost of biodiesel. However, to produce fuel-grade biodiesel, the characteristics of feedstock are very important during the initial research and production stage since the fuel properties mainly depend on the feedstock properties. This review paper presents both biodiesel productions from various feedstocks and their effects on the fuel properties.

  13. A Decision Support System (DSS for Project Management in the Bio-diesel Industry

    Directory of Open Access Journals (Sweden)

    Alin Paul OLTEANU

    2011-01-01

    Full Text Available The European biodiesel industry is currently facing several challenges affecting the profitability of investment projects in the industry. Among these challenges are higher prices for oilseeds, which are the main input for biodiesel production, lower fiscal support by national governments for biodiesel producers and high price volatility of oil markets. Thus identifying all opportunities for optimizing the value chain and lower the production cost of biodiesel is a main requirement for an efficient project management in the biodiesel industry. The paper addresses this topic by developing a decision support system tailored to the needs of Romanian investors in biodiesel production. The system optimizes the main activities of the biodiesel value chain and supports the decision making process at management level. In addition the DSS enables the user to perform sensitivity analysis based on varying various input parameter.

  14. MODEL FOR THE CORRECTION OF THE SPECIFIC GRAVITY OF BIODIESEL FROM RESIDUAL OIL

    Directory of Open Access Journals (Sweden)

    Tatiana Aparecida Rosa da Silva

    2013-06-01

    Full Text Available Biodiesel is a important fuel with economic benefits, social and environmental. The production cost of the biodiesel can be significantly lowered if the raw material is replaced by a alternative material as residual oil. In this study, the variation of specific gravity with temperature increase for diesel and biodiesel from residual oil obtained by homogeneous basic catalysis. All properties analyzed for biodiesel are within specification Brazil. The determination of the correction algorithm for the specific gravity function of temperature is also presented, and the slope of the line to diesel fuel, methylic biodiesel (BMR and ethylic biodiesel (BER from residual oil were respectively the values -0.7089, -0.7290 and -0.7277. This demonstrates the existence of difference of the model when compared chemically different fuels, like diesel and biodiesel from different sources, indicating the importance of determining the specific algorithm for the operations of conversion of volume to the reference temperature.

  15. Novel process integration for biodiesel blend in membrane reactive divided wall (MRDW column

    Directory of Open Access Journals (Sweden)

    Sakhre Vandana

    2016-03-01

    Full Text Available The paper proposes a novel process integration for biodiesel blend in the Membrane assisted Reactive Divided Wall Distillation (MRDW column. Biodiesel is a green fuel and grade of biodiesel blend is B20 (% which consist of 20% biodiesel and rest 80% commercial diesel. Instead of commercial diesel, Tertiary Amyl Ethyl Ether (TAEE was used as an environment friendly fuel for blending biodiesel. Biodiesel and TAEE were synthesized in a pilot scale reactive distillation column. Dual reactive distillation and MRDW were simulated using aspen plus. B20 (% limit calculation was performed using feed flow rates of both TAEE and biodiesel. MRDW was compared with dual reactive distillation column and it was observed that MRDW is comparatively cost effective and suitable in terms of improved heat integration and flow pattern.

  16. Study on Emission and Performance of Diesel Engine Using Castor Biodiesel

    Directory of Open Access Journals (Sweden)

    Md. Saiful Islam

    2014-01-01

    performance of diesel engine using the castor biodiesel and its blend with diesel from 0% to 40% by volume. The acid-based catalyzed transesterification system was used to produce castor biodiesel and the highest yield of 82.5% was obtained under the optimized condition. The FTIR spectrum of castor biodiesel indicates the presence of C=O and C–O functional groups, which is due to the ester compound in biodiesel. The smoke emission test revealed that B40 (biodiesel blend with 40% biodiesel and 60% diesel had the least black smoke compared to the conventional diesel. Diesel engine performance test indicated that the specific fuel consumption of biodiesel blend was increased sufficiently when the blending ratio was optimized. Thus, the reduction in exhaust emissions and reduction in brake-specific fuel consumption made the blends of caster seed oil (B20 a suitable alternative fuel for diesel and could help in controlling air pollution.

  17. Optimization of Substrate Feeding for Enzymatic Biodiesel Production

    DEFF Research Database (Denmark)

    Price, Jason Anthony; Huusom, Jakob Kjøbsted; Nordblad, Mathias

    to be effective in mitigating the effects of substrate inhibition. Using enzymatic biodiesel production as a case study, the volumetric productivity of the reactor is increased while minimizing inactivation of the enzyme due to the alcohol. This is done by using a simple optimization routine where the substrate...... (both the vegetable oil and alcohol) feed rate/concentration is manipulated simultaneously. The results of the simulation were tested in the laboratory and are sufficiently positive to suggest the implementation of a feeding strategy for large scale enzymatic biodiesel production....

  18. Moving towards a Competitive Fully Enzymatic Biodiesel Process

    Directory of Open Access Journals (Sweden)

    Silvia Cesarini

    2015-06-01

    Full Text Available Enzymatic biodiesel synthesis can solve several problems posed by the alkaline-catalyzed transesterification but it has the drawback of being too expensive to be considered competitive. Costs can be reduced by lipase improvement, use of unrefined oils, evaluation of soluble/immobilized lipase preparations, and by combination of phospholipases with a soluble lipase for biodiesel production in a single step. As shown here, convenient natural tools have been developed that allow synthesis of high quality FAMEs (EN14214 from unrefined oils in a completely enzymatic single-step process, making it fully competitive.

  19. Pengaruh Zat Aditif Urea terhadap Kuantitas Biodiesel Pada Reaksi Transesterfikasi

    Directory of Open Access Journals (Sweden)

    Rismawati Rasyid

    2017-03-01

    Full Text Available Abstrak Asam lemak jenuh maupun tak jenuh pada minyak nabati memiliki potensi untuk diubah menjadi bahan kimia penyusun bahan bakar . Komponen asam lemak pada CPO RBD dengan komposisi terbesar adalah asam palmitat (38.2% dan asam oleat (45.89%.  Pembuatan biodiesel dalam penelitian ini menggunakan CPO (Crude Palm Oil yang telah dimurnikan melalui reaksi transesterfikasi dengan pereaksi etanol dan katalisator KOH. Penambahan urea sebagai zat aditif pada reaksi dapat meningkatkan kualitas biodiesel yang diperoleh serta lebih efisien dalam tahapan pemurnian. Persentase kadar FAME (Fatty Acid Metyl Ester setara dengan persen yield biodiesel pada proses reaksi tanpa penambahan urea adalah 90.34% dan mengalami peningkatan setelah penambahan urea sebesar 98%. Densitas yang dihasilkan pada reaksi tanpa zat aditif  0.868 gr/ ml dan reaksi dengan penambahan zat aditif memiliki densitas  0.866 gr/ml,  kedua produk tersebut telah sesuai dengan standar SNI yakni berkisar 0.85–0.89. Kata kunci : biodiesel, CPO, zat aditif Abstract Saturated and unsaturated fatty acids in vegetable oils have potential to be converted into constituent of chemicals fuel. Fatty acids in the RBD palm oil with the largest composition are palmitic acid (38.2% and oleic acid (45.89%. Production of fuel which substitute diesel fuel (biodiesel from CPO (Crude Palm Oil which has been purified by transesterification reaction with ethanol reagent and KOH catalyst. The addition of urea as an additive substancein the reaction to improve  the quality as well as more efficient biodiesel obtained in the purification stages. Percentage value of FAME(Fatty Acid Metyl Esteror yield biodiesel in the reaction without the addition of urea is 90.34% and after the addition of urea increased by 98%. Density of product that produced in the reaction without additives is 0.868 g / ml and for reaction with additives has a density of 0.866 g / ml, both of these products are met the criteria of SNI

  20. Potency of Microalgae as Biodiesel Source in Indonesia

    Directory of Open Access Journals (Sweden)

    H Hadiyanto

    2012-04-01

    Full Text Available Within 20 years, Indonesia should find another energy alternative to substitutecurrent fossil oil. Current use of renewable energy is only 5% and need to be improved up to 17%of our energy mix program. Even though, most of the area in Indonesia is covered by sea, howeverthe utilization of microalgae as biofuel production is still limited. The biodiesel from currentsources (Jatropha, palm oil, and sorghum is still not able to cover all the needs if the fossil oilcannot be explored anymore. In this paper, the potency of microalgae in Indonesia was analysed asthe new potential of energy (biodiesel sources.

  1. Fed-Batch Feeding Strategies for Enzymatic Biodiesel Production

    DEFF Research Database (Denmark)

    Price, Jason Anthony; Nordblad, Mathias; Woodley, John

    2014-01-01

    of the differences in the interfacial and bulk concentrations of the enzyme. The model is then used to evaluate various feeding strategies to improve the enzymatic biodiesel production. The feeding strategies investigated, gave insight into how the methanol should be fed to potentially mitigate enzyme deactivation...... while improving the biodiesel yield. The best experimental results gave a yield of 703 .76 g FAME L-1 and a reactor productivity of 28.12 g FAME L-1 h-1. In comparison, to reach the same yield, the optimised two step feeding strategy took 6.25 hours less, which equates to an increase the reactor...

  2. Enzymatic Production of FAME Biodiesel with Soluble Lipases

    DEFF Research Database (Denmark)

    T. Gundersen, Maria; Heltborg, Carsten Kirstejn; Yang, V

    Biodiesel is a viable alternative to fossil fuels, and biocatalysis is gaining interest as a greener process. We focus on converting oils to Fatty Acid Methyl Ester (FAME) using soluble lipases, which offer an advantage compared to immobilized enzymes by cost efficiency and ease of implementation...... the defined operating space concerning: temperature, water content, initial methanol concentration and enzyme content. The identified optimum range was experimentally evaluated, and model findings were confirmed. Another barrier in lipase use in biodiesel production is the higher melting point (m...

  3. Mechanistic Modelling of Biodiesel Production using a Liquid Lipase Formulation

    DEFF Research Database (Denmark)

    Price, Jason Anthony; Hofmann, Björn; Silva, Vanessa T. L.

    2014-01-01

    , with respect to the industrial production of biodiesel. The developed kinetic model, coupled with a mass balance of the system, was fitted to and validated on experimental results for the fed-batch transesterification of rapeseed oil. The confidence intervals of the parameter estimates, along...... that constrains the amount of methanol in the reactor was computed and the predictions experimentally validated. Monte-Carlo simulations were then used to characterize the effect of the parameter uncertainty on the model outputs, giving a biodiesel yield, based on the mass of oil, of 90.8 ± 0.55 mass %. © 2014...

  4. Optimization of Substrate Feeding for Enzymatic Biodiesel Production

    DEFF Research Database (Denmark)

    Price, Jason Anthony; Huusom, Jakob Kjøbsted; Nordblad, Mathias

    2013-01-01

    to be effective in mitigating the effects of substrate inhibition. Using enzymatic biodiesel production as a case study, the volumetric productivity of the reactor is increased while minimizing inactivation of the enzyme due to the alcohol. This is done by using a simple optimization routine where the substrate...... (both the vegetable oil and alcohol) feed rate/concentration is manipulated simultaneously. The results of the simulation were tested in the laboratory and are sufficiently positive to suggest the implementation of a feeding strategy for large scale enzymatic biodiesel production....

  5. Alabama Institute for Deaf and Blind Biodiesel Project Green

    Energy Technology Data Exchange (ETDEWEB)

    Edmiston, Jessica L

    2012-09-28

    Through extensive collaboration, Alabama Institute for Deaf and Blind (AIDB) is Alabama's first educational entity to initiate a biodiesel public education, student training and production program, Project Green. With state and national replication potential, Project Green benefits local businesses and city infrastructures within a 120-mile radius; provides alternative education to Alabama school systems and to schools for the deaf and blind in Appalachian States; trains students with sensory and/or multiple disabilities in the acquisition and production of biodiesel; and educates the external public on alternative fuels benefits.

  6. Pembuatan Biodiesel dari Limbah Minyak Ikan Patin Menggunakan Reaktor Membran

    OpenAIRE

    Rahmi, Silvia; Syarfi, Syarfi; Irdoni, Irdoni

    2015-01-01

    Membrane reactor is an alternative technology is used to produce of biodiesel, one of the advantages of the reaction and separation process takes place in a single stage simultaneous. This research aims to study the effect of the variation of the catalyst and mole ratio feed catfish oil - methanol in biodiesel production, transesterification process in a membrane reactor with a variation of the mole ratio of catfish oil - methanol 1:10, 1:14, and 1:18, the concentration of the base catalyst 0...

  7. Biodiesel Performance within Internal Combustion Engine Fuel System - A Review

    Directory of Open Access Journals (Sweden)

    Z.A. Khan

    2016-06-01

    Full Text Available This review paper highlights the tribological performance of biodiesel at contacting surfaces in the fuel delivery system of compression ignition (diesel engines. The focus is on the injection components that include low and high pressure injection pumps, diesel fuel injectors, electro-hydraulic valves, diesel fuel lubricity measurements and effects of biodiesel on the running conditions in a diesel fuel injection system. The common rail system and the distributor pump injection systems with electronic diesel control are among the modern trends that are specifically highlighted. Boundary, mixed and hydrodynamic lubrication regimes together with lubricant oil film thickness, pressure and engine performance are also considered.

  8. Simulation, optimization and analysis of cost of biodiesel plant pot route enzymatic; Simulacao, otimizacao e analise de custo de planta de biodiesel via rota enzimatica

    Energy Technology Data Exchange (ETDEWEB)

    Mendes, Jocelia S.; Ferreira, Andrea L.O. [Universidade Federal do Ceara (UFC), Fortaleza, CE (Brazil); Silva, Giovanilton F. [Tecnologia Bioenergetica - Tecbio, Fortaleza, CE (Brazil)

    2008-07-01

    The aim of this work ware simulation, optimization and to find the biodiesel production cost produced by enzymatic route. Consequently, it was carried out a methodology of economic calculations and sensitivity analyses for this process. It was used a computational software from balance equations for obtaining the biodiesel cost. The economical analysis was obtained by capital cost of biofuel. The whole process was developed according analysis of fixed capital cost, total manufacturing cost, raw material cost, and chemical cost. The results of economic calculations to biodiesel production showed efficient. The model was meant for use in assessing the effects on estimated biodiesel production cost of changes in different types of oils. (author)

  9. The economic impact of Canadian biodiesel production on Canadian grains, oilseeds and livestock producers : final report

    International Nuclear Information System (INIS)

    Stiefelmeyer, K.; Mussell, A.; Moore, T.L.; Liu, D.

    2006-05-01

    This study was conducted to provide the Canadian Canola Growers Association with an understanding of the economic effects of a mandated use of biodiesel blends produced in Canada, focusing on canola and canola oil. A literature review was performed to determine what has been found elsewhere in terms of biodiesel. An overview of the feedstock markets was also conducted along with an empirical analysis to determine likely feedstock purchasing behaviour under biodiesel blend requirements. The analysis also considered the rendered animal fats industry. The objectives were to identify the economic impacts of biodiesel development; determine the nature of markets for candidate feedstocks that could be used in manufacturing biodiesel; estimate the economic effects of a 2 per cent biodiesel blend requirement in petroleum diesel; estimate the economic effects of a 5 per cent biodiesel blend requirement in petroleum diesel; and, determine the ultimate impact on the Canadian canola industry of the mandated biodiesel blend. It was shown that biodiesel can be made from a range of feedstocks and that the 2 key factors influencing the success of biodiesel manufacturing facilities were feedstock prices and feedstock availability. The key competitors facing canola oil in the biodiesel market are rendered oils, rendered animal fats, palm oil, and soybean oil. Canola and soybean oil are likely to be relatively high cost feedstocks for biodiesel production, while yellow grease, tallow, and palm oil would be better priced as feed for industrial uses. Two conceptions of market dynamic were considered. In the first, the feedstock prices remained constant, while in the other the feedstock prices fluctuated with volume consumed. It was concluded that if total fat and oil supplies are fixed at historic levels, biodiesel blend requirements of just over 2 per cent are feasible. It was concluded that a cluster of widely available, low-priced feedstocks for biodiesel production exists. These

  10. Bio-Diesel production and Effect of Catalytic Converter on Emission performance with Bio-Diesel Blends

    OpenAIRE

    R.Murali Manohar; M.Prabhahar; Dr.S.Sendil velan

    2010-01-01

    Bio-Diesel the word itself defines almost all the features of the Bio-Diesel literary. In the Era of this Global Warming where the people are making their living more and more comfortable and they are deteriorating the environment also. The uses of the automobiles with the conventional source of fuel leads to the production of the toxic gaseous substances like carbon monoxide, carbon dioxide, oxides of nitrogen, oxide of sulphur, hydro-carbons etc. The limitation comes with the rise in the pr...

  11. Effect of poultry fat oil biodiesel on tractor engine performance

    Directory of Open Access Journals (Sweden)

    M Bavafa

    2016-04-01

    Full Text Available Introduction: Depletion of fossil fuels and environmental degradation are two major problems faced by the world. Today fossil fuels take up to 80% of the primary energy consumed in the world, of which 58% is consumed by the transport sector alone (Mard et al., 2012. The combustion products cause global warming, which is caused of emissions like carbon monoxide (CO, sulfur dioxide (SO2 and nitrogen oxides (NOX. Thus it is essential that low emission alternative fuels to be developed for useing in diesel engines. Many researchers have concluded that biodiesel holds promise as an alternative fuel for diesel engines. Biodiesel is oxygenated, biodegradable, non-toxic, and environmentally friendly (Qi et al., 2010. Materials and Methods: In this study transesterification method was used to produce biodiesel, because of its simplicity in biodiesel production process and holding the highest conversion efficiency. Transesterification of poultry fat oil and the properties of the fuels: Fatty acid methyl ester of poultry fat oil was prepared by transesterification of oil with methanol in the presence of KOH as catalyst. The fuel properties of poultry fat oil methyl ester and diesel fuel were determined. These properties are presented in Table 1. Tests of engine performance and emissions: After securing the qualitative characteristics of produced biodiesel, different biodiesel fuels of 5%, 10%, 15%, and 20% blended with diesel fuel were prepared. A schematic diagram of the engine setup is shown in Fig.1. The MF-399 tractor engine was used in the tests. The basic specifications of the engine are shown in Table 3. The engine was loaded with an electromagnetic dynamometer. The Σ5 model dynamometer manufactured by NJ-FROMENT was used to measure the power and the torque of the tractor engine. The speed range and capacity of this device are shown in Table 2. A FTO Flow Meter, manufactured by American FLOWTECH Company, was used to measure the fuel consumption

  12. Mechanical algal disruption for efficient biodiesel extraction

    Science.gov (United States)

    Krehbiel, Joel David

    Biodiesel from algae provides several benefits over current biodiesel feedstocks, but the energy requirements of processing algae into a useable fuel are currently so high as to be prohibitive. One route to improving this is via disruption of the cells prior to lipid extraction, which can significantly increase energy recovery. Unfortunately, several obvious disruption techniques require more energy than can be gained. This dissertation examines the use of microbubbles to improve mechanical disruption of algal cells using experimental, theoretical, and computational methods. New laboratory experiments show that effective ultrasonic disruption of algae is achieved by adding microbubbles to an algal solution. The configuration studied flows the solution through a tube and insonifies a small section with a high-pressure ultrasound wave. Previous biomedical research has shown effective cell membrane damage on animal cells with similar methods, but the present research is the first to extend such study to algal cells. Results indicate that disruption increases with peak negative pressure between 1.90 and 3.07 MPa and with microbubble concentration up to 12.5 x 107 bubbles/ml. Energy estimates of this process suggest that it requires only one-fourth the currently most-efficient laboratory-scale disruption process. Estimates of the radius near each bubble that causes disruption (i.e. the disruption radius) suggest that it increases with peak negative pressure and is near 9--20 microm for all cases tested. It is anticipated that these procedures can be designed for better efficiency and efficacy, which will be facilitated by identifying the root mechanisms of the bubble-induced disruption. We therefore examine whether bubble expansion alone creates sufficient cell deformation for cell rupture. The spherically-symmetric Marmottant model for bubble dynamics allows estimation of the flow regime under experimental conditions. Bubble expansion is modeled as a point source of

  13. Fuel Pellets Production from Biodiesel Waste

    Directory of Open Access Journals (Sweden)

    Kawalin Chaiyaomporn

    2010-01-01

    Full Text Available This research palm fiber and palm shell were used as raw materials to produce pelletised fuel, and waste glycerol were used as adhesive to reduce biodiesel production waste. The aim of this research is to find optimum ratio of raw material (ratio of palm fiber and palm shell, raw material size distribution, adhesive temperature, and ratio of ingredients (ratio of raw material, waste glycerol, and water. The optimum ratio of pelletized fuel made only by palm fiber was 50:10:40; palm fiber, water, and waste glycerol respectively. In the best practice condition; particle size was smaller than 2 mm, adhesive glycerol was heated. From the explained optimum ratio and ingredient, pelletizing ratio was 62.6%, specific density was 982.2 kg/m3, heating value was 22.5 MJ/kg, moisture content was 5.9194%, volatile matter was 88.2573%, fix carbon content was 1.5894%, and ash content was 4.2339% which was higher than the standard. Mixing palm shell into palm fiber raw material reduced ash content of the pellets. The optimum raw material ratio, which minimizes ash content, was 80 to 20 palm fiber and palm shell respectively. Adding palm shell reduced ash content to be 2.5247% which was higher than pelletized fuel standard but followed cubed fuel standard. At this raw material ratio, pelletizing ratio was 70.5%, specific density was 774.8 kg/m3, heating value was 19.71 MJ/kg, moisture content was 9.8137%, volatile matter was 86.2259%, fix carbon content was 1.4356%, and compressive force was 4.83 N. Pelletized fuel cost at optimum condition was 1.14 baht/kg.

  14. Short term endurance results on a single cylinder diesel engine fueled with upgraded bio oil biodiesel emulsion

    Science.gov (United States)

    Prakash, R.; Murugan, S.

    2017-11-01

    This paper deliberates the endurance test outcomes obtained from a single cylinder, diesel engine fueled with an upgraded bio oil biodiesel emulsion. In this investigation a bio oil obtained by pyrolysis of woody biomass was upgraded with acid treatment. The resulted bio oil was emulsified with addition of biodiesel and suitable surfactant which is termed as ATJOE15. The main objective of the endurance test was to evaluate the wear characteristics of the engine components and lubrication oil properties, when the engine is fueled with the ATJOE15 emulsion. The photographic views taken before and after the end of 100 hrs endurance test, and visual inspection of the engine components, wear and carbon deposit results, are discussed in this paper.

  15. Biodiesel: most recent developments in distribution infra-structure; Recentes desenvolvimentos na infra-estrutura do biodiesel: caso pratico apresentando desde a compra do biodiesel ate a mistura automatizada nas bases

    Energy Technology Data Exchange (ETDEWEB)

    Kauer, Luiz Athayde da Silva; Silberman Luis [Petroleo Ipiranga (Grupo ULTRA), Rio Grande, RS (Brazil)

    2008-07-01

    This presentation will show a practical large scale case of, which involves: the purchase, distribution and storage of 80 million liters of Biodiesel that we have bought in the Brazilian market; the way the distribution is being done and the future perspectives in its infra-structure. Moreover, this presentation will approach and detail the most recent developments in: automation of the mix in the terminals of distribution. Specific analysis of our terminal in Rio de Janeiro - Brazil; identification of the best practice and the results already obtained from it; identification of the tie breaker criteria to produce the mix of the Biodiesel in the Diesel oil; what we are doing to development the modals of transportation of Biodiesel; the Biodiesel storage - Best operational practices; the Biodiesel - aspects for the consumer quality control; acquisition of 5 thousand tons of carbon credits. (author)

  16. Artificial Intelligent Control for a Novel Advanced Microwave Biodiesel Reactor

    International Nuclear Information System (INIS)

    Wali, W A; Hassan, K H; Cullen, J D; Al-Shamma'a, A I; Shaw, A; Wylie, S R

    2011-01-01

    Biodiesel, an alternative diesel fuel made from a renewable source, is produced by the transesterification of vegetable oil or fat with methanol or ethanol. In order to control and monitor the progress of this chemical reaction with complex and highly nonlinear dynamics, the controller must be able to overcome the challenges due to the difficulty in obtaining a mathematical model, as there are many uncertain factors and disturbances during the actual operation of biodiesel reactors. Classical controllers show significant difficulties when trying to control the system automatically. In this paper we propose a comparison of artificial intelligent controllers, Fuzzy logic and Adaptive Neuro-Fuzzy Inference System(ANFIS) for real time control of a novel advanced biodiesel microwave reactor for biodiesel production from waste cooking oil. Fuzzy logic can incorporate expert human judgment to define the system variables and their relationships which cannot be defined by mathematical relationships. The Neuro-fuzzy system consists of components of a fuzzy system except that computations at each stage are performed by a layer of hidden neurons and the neural network's learning capability is provided to enhance the system knowledge. The controllers are used to automatically and continuously adjust the applied power supplied to the microwave reactor under different perturbations. A Labview based software tool will be presented that is used for measurement and control of the full system, with real time monitoring.

  17. Environmental Impacts of Jatropha curcas Biodiesel in India

    Directory of Open Access Journals (Sweden)

    Simon Gmünder

    2012-01-01

    Full Text Available In the context of energy security, rural development and climate change, India actively promotes the cultivation of Jatropha curcas, a biodiesel feedstock which has been identified as suitable for achieving the Indian target of 20% biofuel blending by 2017. In this paper, we present results concerning the range of environmental impacts of different Jatropha curcas cultivation systems. Moreover, nine agronomic trials in Andhra Pradesh are analysed, in which the yield was measured as a function of different inputs such as water, fertilizer, pesticides, and arbuscular mycorrhizal fungi. Further, the environmental impact of the whole Jatropha curcas biodiesel value chain is benchmarked with fossil diesel, following the ISO 14040/44 life cycle assessment procedure. Overall, this study shows that the use of Jatropha curcas biodiesel generally reduces the global warming potential and the nonrenewable energy demand as compared to fossil diesel. On the other hand, the environmental impacts on acidification, ecotoxicity, eutrophication, and water depletion all showed increases. Key for reducing the environmental impact of Jatropha curcas biodiesel is the resource efficiency during crop cultivation (especially mineral fertilizer application and the optimal site selection of the Jatropha curcas plantations.

  18. An effective modular process for biodiesel manufacturing using heterogeneous catalysis

    NARCIS (Netherlands)

    Dimian, A.C.; Rothenberg, G.

    2016-01-01

    We present an innovative reaction set-up and process for biodiesel manufacturing by heterogeneous catalysis. This process has two key advantages over the state-of-the-art process: it enables a variable reaction time and easy catalyst switching/replacement. The process principle presented here is

  19. Environmental impacts of Jatropha curcas biodiesel in India.

    Science.gov (United States)

    Gmünder, Simon; Singh, Reena; Pfister, Stephan; Adheloya, Alok; Zah, Rainer

    2012-01-01

    In the context of energy security, rural development and climate change, India actively promotes the cultivation of Jatropha curcas, a biodiesel feedstock which has been identified as suitable for achieving the Indian target of 20% biofuel blending by 2017. In this paper, we present results concerning the range of environmental impacts of different Jatropha curcas cultivation systems. Moreover, nine agronomic trials in Andhra Pradesh are analysed, in which the yield was measured as a function of different inputs such as water, fertilizer, pesticides, and arbuscular mycorrhizal fungi. Further, the environmental impact of the whole Jatropha curcas biodiesel value chain is benchmarked with fossil diesel, following the ISO 14040/44 life cycle assessment procedure. Overall, this study shows that the use of Jatropha curcas biodiesel generally reduces the global warming potential and the nonrenewable energy demand as compared to fossil diesel. On the other hand, the environmental impacts on acidification, ecotoxicity, eutrophication, and water depletion all showed increases. Key for reducing the environmental impact of Jatropha curcas biodiesel is the resource efficiency during crop cultivation (especially mineral fertilizer application) and the optimal site selection of the Jatropha curcas plantations.

  20. utilization of some non-edible oil for biodiesel production

    African Journals Online (AJOL)

    Ogunjo Samuel

    greenhouse gas emissions [2]. Biodiesel is a non-conventional energy source produced from edible oil such as soya bean oil, corn oil, groundnut oil, palm oil, and sunflower oil and non-edible oil such as animal fat, waste vegetable oil, jatropha oil, algae oil, and castor oil. It is produced through transesterification process.

  1. A techno-economic analysis of biodiesel production from microalgae

    NARCIS (Netherlands)

    Olivieri, G.; Guida, T.; Salatino, P.; Marzocchella, A.

    2013-01-01

    The preliminary assessment of a cost-effective flow-sheet for the production of biodiesel from microalgae lipid fraction was carried out. The study was based on approximated cost-estimation methods integrated with the simulation software Aspen Plus (R). Several scenarios were investigated to compare

  2. Physico-chemical characteristics of oil and biodiesel from Nigerian ...

    African Journals Online (AJOL)

    The oil and biodiesel produced from Nigerian and Indian Jatropha curcas seeds were evaluated using a parametric Student's t-test model. The characteristics assessed include oil yield, specific gravity, density, acid value, free fatty acid, iodine value, saponification value, peroxide value, viscosity and flash point. The results ...

  3. Optimization of biodiesel production from rice bran oil via ...

    African Journals Online (AJOL)

    DR. NJ TONUKARI

    2011-11-16

    Nov 16, 2011 ... The lipase-catalyzed transesterification of rice bran oil and methanol for biodiesel production in hexane was investigated. The effects of different hexane weight ratio, methanol molar ratio, reaction temperature and immobilized lipase dosage on the total conversion were systematically analyzed by response ...

  4. The Paraense Network of Family Agriculture and Biodiesel

    Directory of Open Access Journals (Sweden)

    Rodrigo Corrêa Diniz Peixoto

    2008-12-01

    Full Text Available The production of biodiesel in agreement with the logic of the small scale family agriculture demands several institutional efforts. It is necessary agronomical and technological researches, and the production needs to be developed by means of associations and co-operatives. Agricultural zoning and credit, besides technical assistance, are also important aspects to the activity, whose proposal is to create a new market alternative, without environmental damage and without hammering the production of food. It means that the production of biodiesel, to attend to the family agriculture, requires the integration of many approaches. That integration can be reached by means of a systemic action, able to articulate several institutional competences to the interests of small farmers and agrarian reform settlers. That is the aim of the Paraense Network of Family Agriculture and Biodiesel. More than simply building a forum to debate the subject, the network look for the articulation of institutional competences around projects, defined according to territorial contexts. In that sense, the network is integrated to the project Araguaiana Biodiesel, whose goal is to develop, with the support of Petrobras, a vigorous action in Southern Pará. To this institutional ensemble has joined in a decisive way the Secretary of Agriculture of the State of Pará.

  5. A Review of Microwave-Assisted Reactions for Biodiesel Production

    Directory of Open Access Journals (Sweden)

    Saifuddin Nomanbhay

    2017-06-01

    Full Text Available The conversion of biomass into chemicals and biofuels is an active research area as trends move to replace fossil fuels with renewable resources due to society’s increased concern towards sustainability. In this context, microwave processing has emerged as a tool in organic synthesis and plays an important role in developing a more sustainable world. Integration of processing methods with microwave irradiation has resulted in a great reduction in the time required for many processes, while the reaction efficiencies have been increased markedly. Microwave processing produces a higher yield with a cleaner profile in comparison to other methods. The microwave processing is reported to be a better heating method than the conventional methods due to its unique thermal and non-thermal effects. This paper provides an insight into the theoretical aspects of microwave irradiation practices and highlights the importance of microwave processing. The potential of the microwave technology to accomplish superior outcomes over the conventional methods in biodiesel production is presented. A green process for biodiesel production using a non-catalytic method is still new and very costly because of the supercritical condition requirement. Hence, non-catalytic biodiesel conversion under ambient pressure using microwave technology must be developed, as the energy utilization for microwave-based biodiesel synthesis is reported to be lower and cost-effective.

  6. Process optimization of biodiesel production from wild rapeseed (Brassica campestris

    Directory of Open Access Journals (Sweden)

    Héctor Ramírez

    2012-03-01

    Full Text Available The objectives of this study were, to optimize the performance of biodiesel from rapeseed wild oil depending on the molar ratio methanol / oil, the concentration of NaOH and KOH homogeneous catalysts, temperature and time of transesterification through the response surface methodology, and determining the physicochemical characteristics of biodiesel obtained under optimized conditions. A Plackett and Burman (PB12 design was applied for the screening stage and a rotatable central composite design (DCCR for the final optimization. The conditions that maximize the yield of biodiesel (77.8% were obtained at concentrations of 0 to 0.2% NaOH and 0.4 to 0.6% KOH, with time from 77 to 81 minutes, keeping constant the molar ratio of methanol/oil in 6/1 and a temperature of 60 °C. The physicochemical properties of biodiesel obtained under optimized conditions meet the technical specifications given by ASTM D6751 - 07 and EN14214

  7. Low-Cost Feedstock Conversion to Biodiesel via Ultrasound Technology

    Directory of Open Access Journals (Sweden)

    Farouk Ameer

    2010-10-01

    Full Text Available Biodiesel has attracted increasing interest and has proved to be a good substitute for fossil-based fuels due to its environmental advantages and availability from renewable resources such as refined and waste vegetable oils. Several studies have shown that biodiesel is a better fuel than the fossil-derived diesel in terms of engine performance, emissions reduction, lubricity and environmental benefits. The increasing popularity of biodiesel has generated great demand for its commercial production methods, which in turn calls for the development of technically and economically sound process technologies. This paper explores the applicability of ultrasound in the optimization of low-cost feedstock – in this case waste cooking oil – in the transesterification conversion to biodiesel. It was found that the conversion efficiency of the waste oil using ultrasound was higher than with the mechanical stirring method. The optimized variables of 6:1 methanol/oil ratio at a reaction temperature of 30 °C and a reaction time of 30 min and 0.75% KOH (wt/wt catalyst concentration was obtained for the transesterification of the waste oil via the use of ultrasound.

  8. investigating the production ting the production of biodiesel from ...

    African Journals Online (AJOL)

    eobe

    reaction temperature, time of reaction and oil to m preliminary investigation of ... Biodiesel fuel is one example of biom energy and it is generally ..... Table 2: Percentage FFA of the Mango Seed Oil before. Esterification. Table 3: Percentage FFA of the Mango Seed Oil after. Esterification. Properties First titre value. (Average).

  9. Computational optimization of biodiesel combustion using response surface methodology

    Directory of Open Access Journals (Sweden)

    Ganji Prabhakara Rao

    2017-01-01

    Full Text Available The present work focuses on optimization of biodiesel combustion phenomena through parametric approach using response surface methodology. Physical properties of biodiesel play a vital role for accurate simulations of the fuel spray, atomization, combustion, and emission formation processes. Typically methyl based biodiesel consists of five main types of esters: methyl palmitate, methyl oleate, methyl stearate, methyl linoleate, and methyl linolenate in its composition. Based on the amount of methyl esters present the properties of pongamia bio-diesel and its blends were estimated. CONVERGETM computational fluid dynamics software was used to simulate the fuel spray, turbulence and combustion phenomena. The simulation responses such as indicated specific fuel consumption, NOx, and soot were analyzed using design of experiments. Regression equations were developed for each of these responses. The optimum parameters were found out to be compression ratio – 16.75, start of injection – 21.9° before top dead center, and exhaust gas re-circulation – 10.94%. Results have been compared with baseline case.

  10. Biodegradation of biodiesel/diesel blends by Candida viswanathii

    African Journals Online (AJOL)

    USER

    2009-06-17

    Jun 17, 2009 ... Without inoculum the biodegradation of diesel oil was higher than biodiesel and blends (47.3, 51.1, 5.7 and 22.1% in ... ferent vegetable oil sources such as soybean, sun-flower, peanut, cotton, palm oil, ... from the waste water of a Brazilian oil refinery (Replan/Petrobras). On Sabouraud's dextrose agar, ...

  11. Dutch business opportunities in the Turkish biodiesel sector

    NARCIS (Netherlands)

    Wiersinga, R.C.; Elbersen, H.W.; Yilmaz, G.

    2009-01-01

    To research possibilities for Dutch businesses to be involved in the Turkish biodiesel sector, a short literature study and unstructured interviews with sector stakeholders were performed. Turkey is interested to develop its biofuel sector particularly to improve its security of energy supply, more

  12. Computational Fluid Dynamics Analysis of High Injection Pressure Blended Biodiesel

    Science.gov (United States)

    Khalid, Amir; Jaat, Norrizam; Faisal Hushim, Mohd; Manshoor, Bukhari; Zaman, Izzuddin; Sapit, Azwan; Razali, Azahari

    2017-08-01

    Biodiesel have great potential for substitution with petrol fuel for the purpose of achieving clean energy production and emission reduction. Among the methods that can control the combustion properties, controlling of the fuel injection conditions is one of the successful methods. The purpose of this study is to investigate the effect of high injection pressure of biodiesel blends on spray characteristics using Computational Fluid Dynamics (CFD). Injection pressure was observed at 220 MPa, 250 MPa and 280 MPa. The ambient temperature was kept held at 1050 K and ambient pressure 8 MPa in order to simulate the effect of boost pressure or turbo charger during combustion process. Computational Fluid Dynamics were used to investigate the spray characteristics of biodiesel blends such as spray penetration length, spray angle and mixture formation of fuel-air mixing. The results shows that increases of injection pressure, wider spray angle is produced by biodiesel blends and diesel fuel. The injection pressure strongly affects the mixture formation, characteristics of fuel spray, longer spray penetration length thus promotes the fuel and air mixing.

  13. Preparation of Jojoba Oil Ester Derivatives for Biodiesel Evaluation

    Science.gov (United States)

    As a result of the increase in commodity vegetable oil prices, it is imperative that non-food oils should be considered as alternative feedstocks for biodiesel production. Jojoba oil is unusual in that it is comprised of wax esters as opposed to the triglycerides found in typical vegetable oils. A...

  14. Biodiesel from non-food alternative feed-stock

    Science.gov (United States)

    As a potential feedstock for biodiesel (BD) production, Jojoba oil was extracted from Jojoba (Simmondsia chinensis L.) plant seeds that contained around 50-60 wt.%, which were explored as non-food alternative feedstocks. Interestingly, Jojoba oil has long-chain wax esters and is not a typical trigly...

  15. Las Vegas Serves up Biodiesel for Local Schools

    Energy Technology Data Exchange (ETDEWEB)

    2004-04-01

    This 2-page Clean Cities fact sheet describes the use of biodiesel as a fuel source in buses by the Clark County School District, located in Las Vegas, NV. It includes information on the history of the program, along with contact information for the local Clean Cities Coordinator and Clark County School District.

  16. Quality Assessment of Biodiesels from Lophira Lanceolata and Zi

    African Journals Online (AJOL)

    M.KYARI

    soap and vegetable-oil based ice-cream. 18 . Table 2.0: Methyl Fatty Acid Esters (approximate wt %) of Biodiesels produced from Ziziphus and. Lophira Seed Oils. Methyl esters. Molecular formula Ziziphus m. Lophira l. Methyl hexadecanoate. Methyl eicosanoate. Methyl-9-octadecenoate. Methyl docosanoate. Methyl-9Z ...

  17. AN EXPERIMENTAL INVESTIGATION ON OXIDATIVE STABILITY OF BIODIESEL

    Directory of Open Access Journals (Sweden)

    Mustafa ÇANAKÇI

    2004-02-01

    Full Text Available Biodiesel is an alternative fuel for diesel engines that can be produced from renewable feed stocks such as vegetable oil and animal fats. These feed stocks are reacted with an alcohol to produce alkyl monoesters. The obtained ester can be used in conventional diesel engines with little or no modification. Biodiesel, especially if produced from highly unsaturated oils, oxidizes more rapidly than diesel fuel. This paper reports the results of accelerated oxidation tests on biodiesel. These tests show the impact of time, oxygen flow rate, temperature, metals, and feedstock type on the rate of oxidation. Blending with diesel fuel and the addition of antioxidants are also explored. The data indicate that without antioxidants, biodiesel will oxidize very quickly at temperatures typical of diesel engines. This oxidation results in increases in peroxide value, acid value, and viscosity. While the peroxide value generally reaches a plateau of about 350 meq O2/kg, the acid value and viscosity increase monotonically as oxidation proceeds.

  18. Aspen Simulation of Diesel-Biodiesel Blends Combustion

    Directory of Open Access Journals (Sweden)

    Pérez-Sánchez Armando

    2015-01-01

    Full Text Available Biodiesel is a fuel produced by transesterification of vegetable oils or animal fats, which currently is gaining attention as a diesel substitute. It represents an opportunity to reduce CO2, SO2, CO, HC, PAH and PM emissions and contributes to the diversification of fuels in Mexico's energetic matrix. The results of the simulation of the combustion process are presented in this paper with reference to an engine specification KUBOTA D600-B, operated with diesel-biodiesel blends. The physicochemical properties of the compounds and the operating conditions of equipment were developed using the simulator Aspen® and supplementary information. The main aspects of the engine working conditions were considered such as diesel-biodiesel ratio, air/fuel mixture, temperature of the combustion gases and heat load. Diesel physicochemical specifications were taken from reports of PEMEX and SENER. Methyl esters corresponding to the transesterification of fatty acids that comprise castor oil were regarded as representative molecules of biodiesel obtained from chromatographic analysis. The results include CO2, water vapor, combustion efficiency, power and lower calorific value of fuels.

  19. Biodiesel Synthesis and Evaluation: An Organic Chemistry Experiment

    Science.gov (United States)

    Bucholtz, Ehren C.

    2007-01-01

    A new lab esterification reaction based on biodiesel preparation and viscosity, which provides a model experience of industrial process to understand oxidation of vicinal alcohols by periodic acid, is presented. This new desertification experiment and periodate analysis of glycerol for the introductory organic chemistry laboratory provides an…

  20. Artificial Intelligent Control for a Novel Advanced Microwave Biodiesel Reactor

    Science.gov (United States)

    Wali, W. A.; Hassan, K. H.; Cullen, J. D.; Al-Shamma'a, A. I.; Shaw, A.; Wylie, S. R.

    2011-08-01

    Biodiesel, an alternative diesel fuel made from a renewable source, is produced by the transesterification of vegetable oil or fat with methanol or ethanol. In order to control and monitor the progress of this chemical reaction with complex and highly nonlinear dynamics, the controller must be able to overcome the challenges due to the difficulty in obtaining a mathematical model, as there are many uncertain factors and disturbances during the actual operation of biodiesel reactors. Classical controllers show significant difficulties when trying to control the system automatically. In this paper we propose a comparison of artificial intelligent controllers, Fuzzy logic and Adaptive Neuro-Fuzzy Inference System(ANFIS) for real time control of a novel advanced biodiesel microwave reactor for biodiesel production from waste cooking oil. Fuzzy logic can incorporate expert human judgment to define the system variables and their relationships which cannot be defined by mathematical relationships. The Neuro-fuzzy system consists of components of a fuzzy system except that computations at each stage are performed by a layer of hidden neurons and the neural network's learning capability is provided to enhance the system knowledge. The controllers are used to automatically and continuously adjust the applied power supplied to the microwave reactor under different perturbations. A Labview based software tool will be presented that is used for measurement and control of the full system, with real time monitoring.

  1. Oxidation and thermal behavior of Jatropha curcas biodiesel ...

    African Journals Online (AJOL)

    The induction period of fresh Jatropha curcas biodiesel (JCB) is 3.27 hr. Also the thermal stability of JCB is very poor in terms of activation energy (Ea) and frequency factor (f). The thermal and oxidation behavior is also affected adversely by the container metal. The present paper is dealing with the study of oxidation and ...

  2. BIODIESEL EXHAUST: THE NEED FOR HUMAN HEALTH EFFECTS RESEARCH

    Science.gov (United States)

    Biodiesel is a diesel fuel alternative that has shown potential of becoming a commercially accepted part of the United States energy infrastructure. In November of 2004, the signing of the Jobs Creation Bill HR4520 marked an important turning point for the future production of bi...

  3. Biodiesel production from butter factory effluent | Schabort | African ...

    African Journals Online (AJOL)

    The increase in energy demand coupled with the depletion of fossil fuels has increased the need for renewable and sustainable energy sources. Butter waste effluent was identified as a possible feedstock for biodiesel. The effects of the temperature, alcohol to oil molar ratio, catalyst concentration and the reaction time were ...

  4. Enzymatic epoxidation of biodiesel optimized by response surface ...

    African Journals Online (AJOL)

    During the enzymatic epoxidation of biodiesel, stearic acid was selected as oxygen carrier. Enzyme screening and the load of stearic acid were investigated. The effects of four main reaction conditions including reaction time, temperature, enzyme load, and mole ratio of H2O2/C=C-bonds on the epoxy oxygen group content ...

  5. Increasing the extraction efficiency of algal lipid for biodiesel ...

    African Journals Online (AJOL)

    Various studies have been conducted recently using microalgal system for the production of algal lipid for biodiesel production. This study aimed at increasing the extraction efficiency of algal lipid from Chlorella sp. by the application of Chlorella viruses. The calorific value of lipid from Chlorella sp. has been reported to be ...

  6. Soybean Oil: Powering a High School Investigation of Biodiesel

    Science.gov (United States)

    De La Rosa, Paul; Azurin, Katherine A.; Page, Michael F. Z.

    2014-01-01

    This laboratory investigation challenges students to synthesize, analyze, and compare viable alternative fuels to Diesel No. 2 using a renewable resource, as well as readily available reagents and supplies. During the experiment, students synthesized biodiesel from soybean oil in an average percent yield of 83.8 ± 6.3%. They then prepared fuel…

  7. Biodiesel production from Jatropha curcas oil catalyzed by whole ...

    African Journals Online (AJOL)

    The main obstacle to using lipase as a catalyst in industrial scale biodiesel production is the cost and availability of the enzyme. To overcome this obstacle, the potential of using a whole cell biocatalyst (for at least partial in situ lipase production) was evaluated as a means to reduce the cost of the lipase. The reaction ...

  8. Production of biodiesel by transesterification of refined soybean oil ...

    African Journals Online (AJOL)

    This study focused on the production of biodiesel via transesterification of refined soybean oil obtained locally. Sodium hydroxide was used as the alkali catalyst and methanol (as alcohol) was used in the transesterification process due to its low cost. The methanol-to-oil molar ratio was maintained at 6:1. The effect of ...

  9. Energetic assessment of soybean biodiesel obtainment in West ...

    African Journals Online (AJOL)

    SAM

    2014-07-16

    Jul 16, 2014 ... This work presents the result of a research that aimed to assess soybean-based biodiesel production in the West region of Paraná State, showing that the growing usage of these fuels happens due to the need for alternatives to the use of fossil fuels, once biomass-based fuels have been an environmentally ...

  10. Biodiesel from Seeds: An Experiment for Organic Chemistry

    Science.gov (United States)

    Goldstein, Steven W.

    2014-01-01

    Plants can store the chemical energy required by their developing offspring in the form of triglycerides. These lipids can be isolated from seeds and then converted into biodiesel through a transesterification reaction. This second-year undergraduate organic chemistry laboratory experiment exemplifies the conversion of an agricultural energy…

  11. A Simple, Safe Method for Preparation of Biodiesel

    Science.gov (United States)

    Behnia, Mahin S.; Emerson, David W.; Steinberg, Spencer M.; Alwis, Rasika M.; Duenas, Josue A.; Serafino, Jessica O.

    2011-01-01

    An experiment suitable for organic chemistry students is described. Biodiesel, a "green" fuel, consists of methyl or ethyl esters of long-chain fatty acids called FAMES (fatty acid methyl esters) or FAEES (fatty acid ethyl esters). A quick way to make FAMES is a base-catalyzed transesterification of oils or fats derived from plants or from animal…

  12. Assessing the greenhouse gas emissions from poultry fat biodiesel

    NARCIS (Netherlands)

    Jorgensen, A.; Bikker, P.; Herrmann, I.T.

    2012-01-01

    This article attempts to answer the question: What will most likely happen in terms of emitted greenhouse gases if the use of poultry fat for making biodiesel used in transportation is increased? Through a well-to-wheel assessment, several different possible scenarios are assessed, showing that

  13. Synthesis of heterogeneous catalyst for the production of biodiesel ...

    African Journals Online (AJOL)

    This study explore the comparison of a suitable heterogeneous catalyst for conversion of triglyceride into fatty acid methyl ester. A series of heterogeneous cerium, manganese, and zinc oxide catalyst supported at mixture of cinder was prepared by co-precipitation and applied for conversion of triglyceride in oil to biodiesel ...

  14. Production of biodiesel using Colocynthis citrullus L. oil over green ...

    African Journals Online (AJOL)

    The production and characterization of biodiesel fuel obtained by means of transesterification over green solid heterogeneous catalyst with Colocynthis citrullus L. oil was investigated. The oil was extracted from the Colocynthis citrullus L. using normal hexane by means of soxhlet extractor. The oil obtained was ...

  15. Locomotive emissions measurements for various blends of biodiesel fuel.

    Science.gov (United States)

    2014-12-01

    The objective of this project was to assess the effects of various blends of biodiesel on locomotive engine exhaust emissions. The : emission tests were conducted on two locomotive models, a Tier 2 EMD SD70ACe and a Tier 1 Plus GE Dash9-44CW, using t...

  16. Energetic assessment of soybean biodiesel obtainment in West ...

    African Journals Online (AJOL)

    This work presents the result of a research that aimed to assess soybean-based biodiesel production in the West region of Paraná State, showing that the growing usage of these fuels happens due to the need for alternatives to the use of fossil fuels, once biomass-based fuels have been an environmentally-friendly ...

  17. Dual bioimprinting of Thermomyces lanuginosus lipase for synthesis of biodiesel

    Directory of Open Access Journals (Sweden)

    Joyeeta Mukherjee

    2016-06-01

    Full Text Available Use of biodiesel as an alternative to non-renewable sources of energy has become an attractive option in recent years. The enzymatic synthesis of biodiesel by transesterification of fats/oils with an alcohol is a much more sustainable route than the chemical method. However, cost effectiveness of the enzymatic route is a major barrier in its commercialization. In this work, a high activity biocatalyst design of Thermomyces lanuginosus lipase is made by dually bioimprinting it with substrate and a surfactant (which is believed to open up the lid covering the active site of the lipase during precipitation of the lipase in organic solvent. When the lipase was bioimprinted with only the surfactants, 28 U of the enzyme/g of oil could yield 99% biodiesel from soybean oil in about 4 h. However, when dually bioimprinted even very low enzyme load 1.4 U/g of oil, yielded 99% biodiesel within 48 h.

  18. utilization of some non-edible oil for biodiesel production

    African Journals Online (AJOL)

    Ogunjo Samuel

    Abstract: In this work, the production of biodiesel from four sources of non-edible oils, namely jatropha, animal fat, waste vegetable oil and castor oil was carried out. It was done using an acid esterification process followed by alkali transesterification in the laboratory. Subsequently the physicochemical properties for four ...

  19. Utilization of some non-edible oil for biodiesel production ...

    African Journals Online (AJOL)

    In this work, the production of biodiesel from four sources of non-edible oils, namely jatropha, animal fat, waste vegetable oil and castor oil was carried out. It was done using an acid esterification process followed by alkali transesterification in the laboratory. Subsequently the physicochemical properties for four blends B100 ...

  20. Study on Biodiesel plants growth performance and tolerance to ...

    African Journals Online (AJOL)

    Abstract. In this research, we studied the growth performance and tolerance of three biodiesel plants namely; Jatropha curcas, Moringa oleifera and Ricinus communis to water stress. Research conducted on the three different soils from Kaita, Jibiya and Mai'adua in the semi-desert environments of Katsina State, Nigeria.

  1. Biodiesel from waste cooking oil in Mexico City.

    Science.gov (United States)

    Sheinbaum, Claudia; Balam, Marco V; Robles, Guillermo; Lelo de Larrea, Sebastian; Mendoza, Roberto

    2015-08-01

    The aim of this article is to evaluate the potential use of biodiesel produced from waste cooking oil in Mexico City. The study is divided in two main areas: the analysis of a waste cooking oil collection pilot project conducted in food markets of a Mexico City region; and the exhaust emissions performance of biodiesel blends measured in buses of the Mexico City public bus transportation network (RTP). Results from the waste cooking oil collection pilot project show that oil quantities disposed depend upon the type of food served and the operational practices in a cuisine establishment. Food markets' waste cooking oil disposal rate from fresh oil is around 10%, but with a very high standard deviation. Emission tests were conducted using the Ride-Along-Vehicle-Emissions-Measuring System in two different types of buses while travelling a regular route. Results shows that the use of biodiesel blends reduces emissions only for buses that have exhaust gas recirculation systems, as analysed by repeated measure analysis of variance. The potential use in Mexico City of waste cooking oil for biodiesel is estimated to cover 2175 buses using a B10 blend. © The Author(s) 2015.

  2. Modifikasi Biodiesel Melalui Reaksi Oksidasi Menggunakan Gelombang Ultrasonik

    Directory of Open Access Journals (Sweden)

    Aisyah Aisyah

    2013-07-01

    Full Text Available Biodiesel is an alternative energy fuel that is sustainable and environmentally safe. However, biodiesel has a higher cloud point than fuel diesel because it contains several saturated fatty acids such as oleic acid, linoleic and linolenic acid so that biodiesel tend to solidify at a temperature higher than the freezing point of diesel. This study aims to modify biodiesel from candlenut oil (Aleurites moluccana through oxidation reaction by KMnO4 using ultrasonic equipment. The products obtained were analyzed using FTIR and GCMS instrument. FTIR analysis showed that spectral data of the four modified samples which run in 20, 30, 40 and 50 minutes practically similar. The methyl ester products are characterized by typical bands at specific frequencies such as stretch of C = O; C-C; C-H (sp3 and = C-H (sp2. Fragmentation patterns by GCMS showed that the oxidation reaction in 20, 30, 40 and 50 minutes did not undergo bond disconnection. The components produced is methyl palmitate, methyl linoleate, methyl oleate, heksadekanoat acid, 9, 12 and 9,17oktadekadienal oktadekadienoat acid.

  3. Potential of wastewater grown algae for biodiesel production and CO

    African Journals Online (AJOL)

    Potential of wastewater grown algae for biodiesel production and CO 2 sequestration. ... African Journal of Biotechnology ... Mixed algae sample showed the highest CO2 fixation rate, followed by Chlorella sp., Scenedesmus incrassatulus, Scenedesmus dimorphus and Chroococcus cohaerens (2.807, 1.627, 1.501, 1.270 ...

  4. Biodiesel compatibility with carbon steel and HDPE parts

    Energy Technology Data Exchange (ETDEWEB)

    Maru, Marcia Marie; Lucchese, Marcia Maria; Legnani, Cristiano; Quirino, Welber Gianini; Balbo, Andrea; Aranha, Isabele Bulhoes; Costa, Lilian Terezinha; Vilani, Cecilia; de Sena, Lidia Agata; Damasceno, Jailton Carreteiro; dos Santos Cruz, Talita; Lidizio, Leandro Reis [Divisao de Metrologia de Materiais-DIMAT, Inmetro, Av. Nossa Senhora das Gracas 50, CEP 25250-020, Duque de Caixas, RJ (Brazil); Ferreira e Silva, Rui [Ceramics Eng. Dept., CICECO, University of Aveiro, 3810-193 Aveiro (Portugal); Jorio, Ado [Divisao de Metrologia de Materiais-DIMAT, Inmetro, Av. Nossa Senhora das Gracas 50, CEP 25250-020, Duque de Caixas, RJ (Brazil); Departamento de Fisica, Universidade Federal de Minas Gerais, Av. Antonio Carlos 6627, CEP 30123-970, Pampulha, Belo Horizonte, MG (Brazil); Achete, Carlos Alberto [Divisao de Metrologia de Materiais-DIMAT, Inmetro, Av. Nossa Senhora das Gracas 50, CEP 25250-020, Duque de Caixas, RJ (Brazil); Programa de Engenharia Metalurgica e de Materiais-PEMM, Centro de Tecnologia, Bloco F, Cidade Universitaria, Universidade Federal do Rio de Janeiro-UFRJ, CEP 21949-900, Rio de Janeiro, RJ (Brazil)

    2009-09-15

    Compatibility of the new environmentally-friendly alternative of diesel engine fuels, biodiesel, with storage and engine part materials, is still an open issue. In this work, the interaction between three fuels (petroleum diesel and two types of biodiesel - soybean and sunflower) and two materials (carbon steel and high density polyethylene) used in storage and automotive tanks, is analyzed in detail. A wide set of characterization techniques was used to evaluate the changes in both solid and fluid materials, as weight change measurement, optical, scanning electron and atomic force (AFM) microscopies, Raman and FTIR spectroscopies, and differential scanning calorimetry. The AFM technique allowed detecting surface roughness and morphology changes in the metallic material following the trends in the weight losses. In the case of polymeric material, weight gain by fluid absorption occurred, being detected by the spectroscopic techniques. The biodiesel fuels underwent some ageing however this phenomenon did not affect the interaction between the biodiesel fuels and the substrates. The petrodiesel, which did not age, caused more significant degradation of the substrates. (author)

  5. Waste to biodiesel: A preliminary assessment for Saudi Arabia.

    Science.gov (United States)

    Rehan, M; Gardy, J; Demirbas, A; Rashid, U; Budzianowski, W M; Pant, Deepak; Nizami, A S

    2017-11-10

    This study presents a preliminary assessment of biodiesel production from waste sources available in the Kingdom of Saudi Arabia (KSA) for energy generation and solution for waste disposal issues. A case study was developed under three different scenarios: (S1) KSA population only in 2017, (S2) KSA population and pilgrims in 2017, and (S3) KSA population and pilgrims by 2030 using the fat fraction of the municipal solid waste. It was estimated that S1, S2, and S3 scenarios could produce around 1.08, 1.10 and 1.41 million tons of biodiesel with the energy potential of 43423, 43949 and 56493 TJ respectively. Furthermore, annual savings of US $55.89, 56.56 and 72.71 million can be generated from landfill diversion of food waste and added to the country's economy. However, there are challenges in commercialization of waste to biodiesel facilities in KSA, including waste collection and separation, impurities, reactor design and biodiesel quality. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Oil industry waste: a potential feedstock for biodiesel production.

    Science.gov (United States)

    Abbas, Javeria; Hussain, Sabir; Iqbal, Muhammad Javid; Nadeem, Habibullah; Qasim, Muhammad; Hina, Saadia; Hafeez, Farhan

    2016-08-01

    The worldwide rising energy demands and the concerns about the sustainability of fossil fuels have led to the search for some low-cost renewable fuels. In this scenario, the production of biodiesel from various vegetable and animal sources has attracted worldwide attention. The present study was conducted to evaluate the production of biodiesel from the oil industry waste following base-catalysed transesterification. The transesterification reaction gave a yield of 83.7% by 6:1 methanol/oil molar ratio, at 60°C over 80 min of reaction time in the presence of NaOH. The gas chromatographic analysis of the product showed the presence of 16 fatty acid methyl esters with linoleic and oleic acid as principal components representing about 31% and 20.7% of the total methyl esters, respectively. The fourier transform infrared spectroscopy spectrum of oil industry waste and transesterified product further confirmed the formation of methyl esters. Furthermore, the fuel properties of oil industry waste methyl esters, such as kinematic viscosity, cetane number, cloud point, pour point, flash point, acid value, sulphur content, cold filter plugging point, copper strip corrosion, density, oxidative stability, higher heating values, ash content, water content, methanol content and total glycerol content, were determined and discussed in the light of ASTM D6751 and EN 14214 biodiesel standards. Overall, this study presents the production of biodiesel from the oil industry waste as an approach of recycling this waste into value-added products.

  7. Characterization of pure plant oil and biodiesel from Jatropha curcas ...

    African Journals Online (AJOL)

    The problems associated with long term availability of conventional hydrocarbon fuels for automotive engines, and the continuous emission of combustion ... study investigates the characteristics of pure plant oils (PPO) of Jatropha curcas and Thevetia nerifolia ; biodiesel produced from them at different methanol/ oil ratio.

  8. Effects of biodiesel on emissions of a bus diesel engine.

    Science.gov (United States)

    Kegl, Breda

    2008-03-01

    This paper discusses the influence of biodiesel on the injection, spray, and engine characteristics with the aim to reduce harmful emissions. The considered engine is a bus diesel engine with injection M system. The injection, fuel spray, and engine characteristics, obtained with biodiesel, are compared to those obtained with mineral diesel (D2) under various operating regimes. The considered fuel is neat biodiesel from rapeseed oil. Its density, viscosity, surface tension, and sound velocity are determined experimentally and compared to those of D2. The obtained results are used to analyze the most important injection, fuel spray, and engine characteristics. The injection characteristics are determined numerically under the operating regimes, corresponding to the 13 mode ESC test. The fuel spray is obtained experimentally under peak torque condition. Engine characteristics are determined experimentally under 13 mode ESC test conditions. The results indicate that, by using biodiesel, harmful emissions (NO(x), CO, smoke and HC) can be reduced to some extent by adjusting the injection pump timing properly.

  9. Technical aspects of biodiesel production from vegetable oils

    Directory of Open Access Journals (Sweden)

    Krishnakumar Janahiraman

    2008-01-01

    Full Text Available Biodiesel, a promising substitute as an alternative fuel has gained significant attention due to the finite nature of fossil energy sources and does not produce sulfur oxides and minimize the soot particulate in comparison with the existing one from petroleum diesel. The utilization of liquid fuels such as biodiesel produced from vegetable oil by transesterification process represents one of the most promising options for the use of conventional fossil fuels. In the first step of this experimental research, edible rice bran oil used as test material and converted into methyl ester and non-edible jatropha vegetable oil is converted into jatropha oil methyl ester, which are known as biodiesel and they are prepared in the presence of homogeneous acid catalyst and optimized their operating parameters like reaction temperature, quantity of alcohol and the catalyst requirement, stirring rate and time of esterification. In the second step, the physical properties such as density, flash point, kinematic viscosity, cloud point, and pour point were found out for the above vegetable oils and their methyl esters. The same characteristics study was also carried out for the diesel fuel for obtaining the baseline data for analysis. The values obtained from the rice bran oil methyl ester and jatropha oil methyl ester are closely matched with the values of conventional diesel and it can be used in the existing diesel engine without any hardware modification. In the third step the storage characteristics of biodiesel are also studied. .

  10. Biodiesel unsaturation degree effects on diesel engine NOx emissions and cotton wick flame temperature

    Directory of Open Access Journals (Sweden)

    Abdullah Mohd Fareez Edzuan

    2017-01-01

    Full Text Available As compared with conventional diesel fuel, biodiesel has better lubricity and lower particulate matter (PM emissions however nitrogen oxides (NOx emissions generally increase in biodiesel-fuelled diesel engine. Strict regulation on NOx emissions is being implemented in current Euro 6 standard and it is expected to be tighter in next standard, thus increase of NOx cannot be accepted. In this study, biodiesel unsaturation degree effects on NOx emissions are investigated. Canola, palm and coconut oils are selected as the feedstock based on their unsaturation degree. Biodiesel blends of B20 were used to fuel a single cylinder diesel engine and exhaust emissions were sampled directly at exhaust tailpipe with a flue gas analyser. Biodiesel flame temperature was measured from a cotton wick burned in simple atmospheric conditions using a thermocouple. Fourier transform infrared (FTIR spectrometer was also used to identify the functional groups presence in the biodiesel blends. Oxygen content in biodiesel may promote complete combustion as the NOx emissions and flame temperatures were increased while the carbon monoxide (CO emissions were decreased for all biodiesel blends. It is interesting to note that the NOx emissions and flame temperatures were directly proportional with biodiesel unsaturation degree. It might be suggested that apart from excess oxygen and free radical formation, higher NOx emissions can also be caused by the elevated flame temperatures due to the presence of double bonds in unsaturated biodiesel.

  11. Performance and emission study on waste cooking oil biodiesel and distillate blends for microturbine application

    Directory of Open Access Journals (Sweden)

    Ee Sann Tan

    2015-11-01

    Full Text Available Biodiesel is defined as domestic renewable energy resource, which can be derived from natural oils through the transesterification. The implementation of biodiesel is essential due to the energy depletion crisis and the impact on exacerbating environment caused by rapid consumption of conventional diesel. Waste cooking oil (WCO was used as the raw material to produce biodiesel in order to reduce wastes polluting the environment. This paper studies the technical potential of WCO biodiesel to be used as an alternative fuel for microturbine. The ASTM D6751 and ASTM D2881 standards were selected as references to evaluate the compatibility with distillate to be used as a microturbine fuel. The performance and emission tests were conducted employing a 30 kW microturbine, without any modification, using biodiesel and distillate blends up to maximum of 20% biodiesel mixing ratio. It was found that the thermal efficiency peaked at 20% biodiesel blend with distillate, despite the fact that biodiesel had a lower calorific value and a higher fuel consumption. The emission test results showed reduction of CO emission by increasing the WCO biodiesel mixing ratio, while NOx emission was dependent on the exhaust gas temperature. In conclusion, biodiesel derived from WCO has the potential to substitute distillate in the microturbine application.

  12. Effect of first and second generation biodiesel blends on engine performance and emission

    Energy Technology Data Exchange (ETDEWEB)

    Azad, A. K., E-mail: azad.cqu@gmail.com, E-mail: a.k.azad@cqu.edu.au; Rasul, M. G., E-mail: m.rasul@cqu.edu.au; Bhuiya, M. M. K., E-mail: m.bhuiya@cqu.edu.au [School of Engineering and Technology, Central Queensland University, Rockhampton, QLD 4702 (Australia); Islam, Rubayat, E-mail: rubayat12@yahoo.com [Department of Mechanical Engineering, Bangladesh University of Engineering and Technology, Dhaka-1000 (Bangladesh)

    2016-07-12

    The biodiesel is a potential source of alternative fuel which can be used at different proportions with diesel fuel. This study experimentally investigated the effect of blend percentage on diesel engine performance and emission using first generation (soybean) and second generation (waste cooking) biodiesel. The characterization of the biodiesel was done according to ASTM and EN standards and compared with ultralow sulfur diesel (ULSD) fuel. A multi-cylinder test bed engine coupled with electromagnetic dynamometer and 5 gas analyzer were used for engine performance and emission test. The investigation was made using B5, B10 and B15 blends for both biodiesels. The study found that brake power (BP) and brake torque (BT) slightly decreases and brake specific fuel consumption (BSFC) slightly increases with an increase in biodiesel blends ratio. Besides, a significant reduction in exhaust emissions (except NO{sub x} emission) was found for both biodiesels compared to ULSD. Soybean biodiesel showed better engine performance and emissions reduction compared with waste cooking biodiesel. However, NO{sub x} emission for B5 waste cooking biodiesel was lower than soybean biodiesel.

  13. Effect of first and second generation biodiesel blends on engine performance and emission

    Science.gov (United States)

    Azad, A. K.; Rasul, M. G.; Bhuiya, M. M. K.; Islam, Rubayat

    2016-07-01

    The biodiesel is a potential source of alternative fuel which can be used at different proportions with diesel fuel. This study experimentally investigated the effect of blend percentage on diesel engine performance and emission using first generation (soybean) and second generation (waste cooking) biodiesel. The characterization of the biodiesel was done according to ASTM and EN standards and compared with ultralow sulfur diesel (ULSD) fuel. A multi-cylinder test bed engine coupled with electromagnetic dynamometer and 5 gas analyzer were used for engine performance and emission test. The investigation was made using B5, B10 and B15 blends for both biodiesels. The study found that brake power (BP) and brake torque (BT) slightly decreases and brake specific fuel consumption (BSFC) slightly increases with an increase in biodiesel blends ratio. Besides, a significant reduction in exhaust emissions (except NOx emission) was found for both biodiesels compared to ULSD. Soybean biodiesel showed better engine performance and emissions reduction compared with waste cooking biodiesel. However, NOx emission for B5 waste cooking biodiesel was lower than soybean biodiesel.

  14. Direct Biodiesel Production from Wet Microalgae Biomass of Chlorella pyrenoidosa through In Situ Transesterification

    Directory of Open Access Journals (Sweden)

    Hechun Cao

    2013-01-01

    Full Text Available A one-step process was applied to directly converting wet oil-bearing microalgae biomass of Chlorella pyrenoidosa containing about 90% of water into biodiesel. In order to investigate the effects of water content on biodiesel production, distilled water was added to dried microalgae biomass to form wet biomass used to produce biodiesel. The results showed that at lower temperature of 90°C, water had a negative effect on biodiesel production. The biodiesel yield decreased from 91.4% to 10.3% as water content increased from 0% to 90%. Higher temperature could compensate the negative effect. When temperature reached 150°C, there was no negative effect, and biodiesel yield was over 100%. Based on the above research, wet microalgae biomass was directly applied to biodiesel production, and the optimal conditions were investigated. Under the optimal conditions of 100 mg dry weight equivalent wet microalgae biomass, 4 mL methanol, 8 mL n-hexane, 0.5 M H2SO4, 120°C, and 180 min reaction time, the biodiesel yield reached as high as 92.5% and the FAME content was 93.2%. The results suggested that biodiesel could be effectively produced directly from wet microalgae biomass and this effort may offer the benefits of energy requirements for biodiesel production.

  15. Pricing model for biodiesel feedstock: A case study of Chhattisgarh in India

    International Nuclear Information System (INIS)

    Pohit, Sanjib; Biswas, Pradip Kumar; Kumar, Rajesh; Goswami, Anandajit

    2010-01-01

    Following the global trend, India declared its biofuel policy in which biodiesel, primarily from jatropha, would meet 20% of the diesel demand beginning with 2011-2012. To promote biofuel, Indian government has announced biodiesel purchase price as well as compulsory blending ratio. But, these measures have not worked to create large scale biodiesel production in India. With this backdrop, this paper highlights about the importance of a sound pricing policy focusing on the entire value chain of biodiesel production. The analysis is based on field level data from Chhattisgarh, the leading state in the production of jatropha. Such a sound pricing policy has to deal with the prices of feedstock, by-products and final product like biodiesel. It would also have to reflect on the business model of production of biodiesel. The simulation exercises in our model shows that the business returns from the production of biodiesel and the minimum support price (MSP) of the feedstock for biodiesel (i.e. jatropha seeds in this case) are sensitive to various parameters like seed yields, technological efficiency, by product and petro-diesel prices. An effective price policy framework has to consider all these factors to create a platform for sustainable biodiesel production in India. - Research highlights: → India's biodiesel program began way back in 2003. → Success is limited. → Effective policy frame is missing. → Paper proposed to address the same with field level observation.

  16. Parametric study of the alkali catalyzed transesterification of waste frying oil for Biodiesel production

    International Nuclear Information System (INIS)

    Al-Hamamre, Zayed; Yamin, Jehad

    2014-01-01

    Highlights: • Investigation of waste frying oil as potential source for Biodiesel production. • Optimization of important reaction parameters. • A high yield and conversion of the feedstock to biodiesel. • Determination of fuel properties of the biodiesel produced from used frying oil. - Abstract: Waste frying oil (WFO) conversion to Biodiesel (Biodiesel) by Alkali-catalyzed transesterification was studied. The effect of operating and processing variables e.g. reaction temperature, MeOH/oil ratio, type of catalyst used and its concentration was investigated at different reaction times. Further, the physical and chemical properties of the WFO and the produced methyl ester (Biodiesel) were measured. Results showed that (within the range of variables studied) the optimum conditions for Biodiesel manufacturing were MeOH/oil ratio 0.4 v/v (corresponds to 9.5 M ratio), with 1.0% (% w/v) KOH (corresponds to 0.83% w/w), temperature of 50 °C and reaction time between 20 and 40 min. Under these conditions, the obtained Biodiesel yield was approximately 98%. Results also showed that the viscosity of the obtained Biodiesel was 5.86 mm 2 /s which is close to that of petrodiesel with an average decrease of 69.5% in comparison with WFO. Furthermore, the iodine value (25.36 g I 2 /100 g sample) and the density (0.877 g/cm 3) of the Biodiesel met the values specified by JUS EN14214

  17. Direct Biodiesel Production from Wet Microalgae Biomass of Chlorella pyrenoidosa through In Situ Transesterification

    Science.gov (United States)

    Cao, Hechun; Zhang, Zhiling; Wu, Xuwen; Miao, Xiaoling

    2013-01-01

    A one-step process was applied to directly converting wet oil-bearing microalgae biomass of Chlorella pyrenoidosa containing about 90% of water into biodiesel. In order to investigate the effects of water content on biodiesel production, distilled water was added to dried microalgae biomass to form wet biomass used to produce biodiesel. The results showed that at lower temperature of 90°C, water had a negative effect on biodiesel production. The biodiesel yield decreased from 91.4% to 10.3% as water content increased from 0% to 90%. Higher temperature could compensate the negative effect. When temperature reached 150°C, there was no negative effect, and biodiesel yield was over 100%. Based on the above research, wet microalgae biomass was directly applied to biodiesel production, and the optimal conditions were investigated. Under the optimal conditions of 100 mg dry weight equivalent wet microalgae biomass, 4 mL methanol, 8 mL n-hexane, 0.5 M H2SO4, 120°C, and 180 min reaction time, the biodiesel yield reached as high as 92.5% and the FAME content was 93.2%. The results suggested that biodiesel could be effectively produced directly from wet microalgae biomass and this effort may offer the benefits of energy requirements for biodiesel production. PMID:24195081

  18. Annex 34 : task 1 : analysis of biodiesel options : biomass-derived diesel fuels : final report

    Energy Technology Data Exchange (ETDEWEB)

    McGill, R. [Oak Ridge National Laboratory, TN (United States); Aakko-Saksa, P.; Nylund, N.O. [TransEnergy Consulting Ltd., Helsinki (Finland)

    2009-06-15

    Biofuels are derived from woody biomass, non-woody biomass, and organic wastes. The properties of vegetable oil feedstocks can have profound effects on the properties of the finished biodiesel product. However, all biodiesel fuels have beneficial effects on engine emissions. This report discussed the use of biodiesel fuels as replacements for part of the diesel fuel consumed throughout the world. Biodiesel fuels currently being produced from fatty acid esters today were reviewed, as well as some of the more advanced diesel replacement fuels. The report was produced as part of the International Energy Agency (IEA) Advanced Motor Fuels (AMF) Implementing Agreement Annex 34, and was divided into 14 sections: (1) an introduction, (2) biodiesel and biomass, (3) an explanation of biodiesel, (4) properties of finished biodiesel fuels, (5) exhaust emissions of finished biodiesel fuels and blends, (6) life-cycle emissions and energy, (7) international biodiesel (FAME) technical standards and specifications, (8) growth in production and use of biodiesel fuels, (9) biofuel refineries, (10) process technology, (11) development and status of biorefineries, (12) comparison of options to produce biobased diesel fuels, (13) barriers and gaps in knowledge, and (14) references. 113 refs., 37 tabs., 74 figs.

  19. Computational fluid dynamics simulation of a single cylinder research engine working with biodiesel

    Directory of Open Access Journals (Sweden)

    Moldovanu Dan

    2013-01-01

    Full Text Available The main objective of the paper is to present the results of the CFD simulation of a DI single cylinder engine using diesel, biodiesel, or different mixture proportions of diesel and biodiesel and compare the results to a test bed measurement in the same functioning point. The engine used for verifying the results of the simulation is a single cylinder research engine from AVL with an open ECU, so that the injection timings and quantities can be controlled and analyzed. In Romania, until the year 2020 all the fuel stations are obliged to have mixtures of at least 10% biodiesel in diesel [14]. The main advantages using mixtures of biofuels in diesel are: the fact that biodiesel is not harmful to the environment; in order to use biodiesel in your engine no modifications are required; the price of biodiesel is smaller than diesel and also if we compare biodiesel production to the classic petroleum based diesel production, it is more energy efficient; biodiesel assures more lubrication to the engine so the life of the engine is increased; biodiesel is a sustainable fuel; using biodiesel helps maintain the environment and it keeps the people more healthy [1-3].

  20. Recent trends, opportunities and challenges of biodiesel in Malaysia: An overview

    International Nuclear Information System (INIS)

    Lim, Steven; Teong, Lee Keat

    2010-01-01

    Energy supply and its security issues have been the topic of interest lately. With growing environmental awareness about the negative implications brought by excessive usage of fossil fuels, the race for finding alternative energy as their substitutions is getting heated up. For now, renewable energy from biodiesel has been touted as one of the most promising substitutions for petroleum-derived diesel. Combustion of biodiesel as fuel is more environment-friendly while retaining most of the positive engine properties of petroleum-derived diesel. Production of biodiesel is also a proven technology with established commercialization activities. The huge potential of biodiesel coupled with the abundance of palm oil which is one of the most cost-effective feedstocks for biodiesel is responsible for the pledging of Malaysia to become the leading producer of high quality biodiesel in the region. Currently, total approved installed capacity of biodiesel production in Malaysia equals to almost 92% of the world biodiesel production output in 2008. While Malaysia does indeed possessed materials, technologies and marketing superiority to vie for that position, many more challenges are still awaiting. The price restriction, provisions controversy, escalating non-tariff trade barriers and negligible public support need to be addressed appropriately. In this review, Malaysia's previous and current position in global biodiesel market, its future potential towards the prominent leading biodiesel status and major disrupting obstacles are being discussed. The feasibility of utilizing algae as the up-and-coming biodiesel feedstock in Malaysia is also under scrutiny. Lastly, several recommendations on the roles played by three major forces in Malaysia's biodiesel industry are presented to tackle the shortcomings in achieving the coveted status by Malaysia. It is hope that Malaysia's progress in biodiesel industry will not only benefit itself but rather as the role model to catalyst the