Basic amino acid residues located in the N-terminal region of BEND3 are essential for its nuclear localization

Energy Technology Data Exchange (ETDEWEB)

Shiheido, Hirokazu, E-mail: shiheido@ak.med.kyoto-u.ac.jp; Shimizu, Jun

2015-02-20

BEN domain-containing protein 3 (BEND3) has recently been reported to function as a heterochromatin-associated protein in transcriptional repression in the nucleus. BEND3 should have nuclear localization signals (NLSs) to localize to the nucleus in light of its molecular weight, which is higher than that allowed to pass through nuclear pore complexes. We here analyzed the subcellular localization of deletion/site-directed mutants of human BEND3 by an immunofluorescence assay in an attempt to identify the amino acids essential for its nuclear localization. We found that three basic amino acid residues located in the N-terminal region of BEND3 (BEND3{sub 56–58}, KRK) are essential, suggesting that these residues play a role as a functional NLS. These results provide valuable information for progressing research on BEND3. - Highlights: • BEND3 localizes to the nucleus. • The N-terminal 60 amino acids region of BEND3 contains NLS. • Amino acids located between 56 and 58 of BEND3 (KRK) are part of NLS. • KRK motif is highly conserved among BEND3 homologs.

The geomorphic effectiveness of a large flood on the Rio Grande in the Big Bend region: insights on geomorphic controls and post-flood geomorphic response

Science.gov (United States)

Dean, David J.; Schmidt, John C.

2013-01-01

Since the 1940s, the Rio Grande in the Big Bend region has undergone long periods of channel narrowing, which have been occasionally interrupted by rare, large floods that widen the channel (termed a channel reset). The most recent channel reset occurred in 2008 following a 17-year period of extremely low stream flow and rapid channel narrowing. Flooding was caused by precipitation associated with the remnants of tropical depression Lowell in the Rio Conchos watershed, the largest tributary to the Rio Grande. Floodwaters approached 1500 m3/s (between a 13 and 15 year recurrence interval) and breached levees, inundated communities, and flooded the alluvial valley of the Rio Grande; the wetted width exceeding 2.5 km in some locations. The 2008 flood had the 7th largest magnitude of record, however, conveyed the largest volume of water than any other flood. Because of the narrow pre-flood channel conditions, record flood stages occurred. We used pre- and post-flood aerial photographs, channel and floodplain surveys, and 1-dimensional hydraulic models to quantify the magnitude of channel change, investigate the controls of flood-induced geomorphic changes, and measure the post-flood response of the widened channel. These analyses show that geomorphic changes included channel widening, meander migration, avulsions, extensive bar formation, and vertical floodplain accretion. Reach-averaged channel widening between 26 and 52% occurred, but in some localities exceeded 500%. The degree and style of channel response was related, but not limited to, three factors: 1) bed-load supply and transport, 2) pre-flood channel plan form, and 3) rapid declines in specific stream power downstream of constrictions and areas of high channel bed slope. The post-flood channel response has consisted of channel contraction through the aggradation of the channel bed and the formation of fine-grained benches inset within the widened channel margins. The most significant post-flood geomorphic

Techniques for processing remote field eddy current signals from bend regions of steam generator tubes of prototype fast breeder reactor

Energy Technology Data Exchange (ETDEWEB)

Thirunavukkarasu, S. [Non Destructive Evaluation Division, Indira Gandhi Centre for Atomic Research, Kalpakkam, TN 603 102 (India); Rao, B.P.C., E-mail: bpcrao@igcar.gov.in [Non Destructive Evaluation Division, Indira Gandhi Centre for Atomic Research, Kalpakkam, TN 603 102 (India); Jayakumar, T.; Raj, Baldev [Non Destructive Evaluation Division, Indira Gandhi Centre for Atomic Research, Kalpakkam, TN 603 102 (India)

2011-04-15

Steam generator (SG) is one of the most critical components of sodium cooled fast breeder reactor. Remote field eddy current (RFEC) technique has been chosen for in-service inspection (ISI) of these ferromagnetic SG tubes made of modified 9Cr-1Mo steel (Grade 91). Expansion bends are provided in the SGs to accommodate differential thermal expansion. During ISI using RFEC technique, in expansion bend regions, exciter-receiver coil misalignment, bending stresses, probe wobble and magnetic permeability variations produce disturbing noise hindering detection of defects. Fourier filtering, cross-correlation and wavelet transform techniques have been studied for noise reduction as well as enhancement of RFEC signals of defects in bend regions, having machined grooves and localized defects. Performance of these three techniques has been compared using signal-to-noise ratio (SNR). Fourier filtering technique has shown better performance for noise reduction while cross-correlation technique has resulted in significant enhancement of signals. Wavelet transform technique has shown the combined capability of noise reduction and signal enhancement and resulted in unambiguous detection of 10% of wall loss grooves and localized defects in the bend regions with SNR better than 7 dB.

Regional analysis of big five personality factors and suicide rates in Russia.

Science.gov (United States)

Voracek, Martin

2013-08-01

Extending cross-national and intranational studies on possible aggregate-level associations between personality dimensions and suicide prevalence, this study examined the associations of the Big Five personality factors and suicide rates across 32 regions of the Russian Federation. Failing to replicate one key finding of similar geographic studies, namely, a correspondence of higher suicide rates with lower Agreeableness and Conscientiousness (i.e., higher Psychoticism) scores, higher suicide rates corresponded to higher Agreeableness scores. This effect was obtained with one available data source (regional-level Big Five ratings based on the National Character Survey), but not with another (based on the NEO-PI-R measure). All in all, regional suicide rates across Russia were dissociated from regional variation in personality dimensions.

Global fluctuation spectra in big-crunch-big-bang string vacua

International Nuclear Information System (INIS)

Craps, Ben; Ovrut, Burt A.

2004-01-01

We study big-crunch-big-bang cosmologies that correspond to exact world-sheet superconformal field theories of type II strings. The string theory spacetime contains a big crunch and a big bang cosmology, as well as additional 'whisker' asymptotic and intermediate regions. Within the context of free string theory, we compute, unambiguously, the scalar fluctuation spectrum in all regions of spacetime. Generically, the big crunch fluctuation spectrum is altered while passing through the bounce singularity. The change in the spectrum is characterized by a function Δ, which is momentum and time dependent. We compute Δ explicitly and demonstrate that it arises from the whisker regions. The whiskers are also shown to lead to 'entanglement' entropy in the big bang region. Finally, in the Milne orbifold limit of our superconformal vacua, we show that Δ→1 and, hence, the fluctuation spectrum is unaltered by the big-crunch-big-bang singularity. We comment on, but do not attempt to resolve, subtleties related to gravitational back reaction and light winding modes when interactions are taken into account

Big Book of Windows Hacks

CERN Document Server

Gralla, Preston

2008-01-01

Bigger, better, and broader in scope, the Big Book of Windows Hacks gives you everything you need to get the most out of your Windows Vista or XP system, including its related applications and the hardware it runs on or connects to. Whether you want to tweak Vista's Aero interface, build customized sidebar gadgets and run them from a USB key, or hack the "unhackable" screensavers, you'll find quick and ingenious ways to bend these recalcitrant operating systems to your will. The Big Book of Windows Hacks focuses on Vista, the new bad boy on Microsoft's block, with hacks and workarounds that

High-sensitivity bend angle measurements using optical fiber gratings.

Science.gov (United States)

Rauf, Abdul; Zhao, Jianlin; Jiang, Biqiang

2013-07-20

We present a high-sensitivity and more flexible bend measurement method, which is based on the coupling of core mode to the cladding modes at the bending region in concatenation with optical fiber grating serving as band reflector. The characteristics of a bend sensing arm composed of bending region and optical fiber grating is examined for different configurations including single fiber Bragg grating (FBG), chirped FBG (CFBG), and double FBGs. The bend loss curves for coated, stripped, and etched sections of fiber in the bending region with FBG, CFBG, and double FBG are obtained experimentally. The effect of separation between bending region and optical fiber grating on loss is measured. The loss responses for single FBG and CFBG configurations are compared to discover the effectiveness for practical applications. It is demonstrated that the sensitivity of the double FBG scheme is twice that of the single FBG and CFBG configurations, and hence acts as sensitivity multiplier. The bend loss response for different fiber diameters obtained through etching in 40% hydrofluoric acid, is measured in double FBG scheme that resulted in a significant increase in the sensitivity, and reduction of dead-zone.

From big bang to big crunch and beyond

International Nuclear Information System (INIS)

Elitzur, Shmuel; Rabinovici, Eliezer; Giveon, Amit; Kutasov, David

2002-01-01

We study a quotient Conformal Field Theory, which describes a 3+1 dimensional cosmological spacetime. Part of this spacetime is the Nappi-Witten (NW) universe, which starts at a 'big bang' singularity, expands and then contracts to a 'big crunch' singularity at a finite time. The gauged WZW model contains a number of copies of the NW spacetime, with each copy connected to the preceding one and to the next one at the respective big bang/big crunch singularities. The sequence of NW spacetimes is further connected at the singularities to a series of non-compact static regions with closed timelike curves. These regions contain boundaries, on which the observables of the theory live. This suggests a holographic interpretation of the physics. (author)

Measurement of turbulent flows in a square sectioned 270 .deg. bend

Energy Technology Data Exchange (ETDEWEB)

Cho, Sok Hyu; Lee, Gun Hyee [Wonkwang Univ., Iksan (Korea, Republic of); Chun, Kun Ho [Korea Univ., Seoul (Korea, Republic of)

2000-07-01

Most of the past experimental or analytical studies were performed for the curved bend with a square cross-section. Velocity profiles and Reynolds stresses of the turbulence flow in the 270 degree bend with circular cross-section were measured by a hot-wire anemometer. The mean velocity of primary flowing direction effected by the downstream of bend in the entry region of the bend. The flow in the inner part of the bend slowed the distribution velocity relatively large and unsymmetric phenomenon. In the strong secondary flow occurred when the flow passed in the region of 45 degree to 90 degree. The secondary flow appeared very large value in the neighbor region inner wall.

Measurement of turbulent flows in a square sectioned 270 .deg. bend

International Nuclear Information System (INIS)

Cho, Sok Hyu; Lee, Gun Hyee; Chun, Kun Ho

2000-01-01

Most of the past experimental or analytical studies were performed for the curved bend with a square cross-section. Velocity profiles and Reynolds stresses of the turbulence flow in the 270 degree bend with circular cross-section were measured by a hot-wire anemometer. The mean velocity of primary flowing direction effected by the downstream of bend in the entry region of the bend. The flow in the inner part of the bend slowed the distribution velocity relatively large and unsymmetric phenomenon. In the strong secondary flow occurred when the flow passed in the region of 45 degree to 90 degree. The secondary flow appeared very large value in the neighbor region inner wall

Flow Structure and Channel Morphology at a Confluent-Meander Bend

Science.gov (United States)

Riley, J. D.; Rhoads, B. L.

2009-12-01

Flow structure and channel morphology in meander bends have been well documented. Channel curvature subjects flow through a bend to centrifugal acceleration, inducing a counterbalancing pressure-gradient force that initiates secondary circulation. Transverse variations in boundary shear stress and bedload transport parallel cross-stream movement of high velocity flow and determine spatial patterns of erosion along the outer bank and deposition along the inner bank. Laboratory experiments and numerical modeling of confluent-meander bends, a junction planform that develops when a tributary joins a meandering river along the outer bank of a bend, suggest that flow and channel morphology in such bends deviate from typical patterns. The purpose of this study is to examine three-dimensional (3-D) flow structure and channel morphology at a natural confluent-meander bend. Field data were collected in southeastern Illinois where Big Muddy Creek joins the Little Wabash River near a local maximum of curvature along an elongated meander loop. Measurements of 3-D velocity components were obtained with an acoustic Doppler current profiler (ADCP) for two flow events with differing momentum ratios. Channel bathymetry was also resolved from the four-beam depths of the ADCP. Analysis of velocity data reveals a distinct shear layer flanked by dual helical cells within the bend immediately downstream of the confluence. Flow from the tributary confines flow from the main channel along the inner part of the channel cross section, displacing the thalweg inward, limiting the downstream extent of the point bar, protecting the outer bank from erosion and enabling bar-building along this bank. Overall, this pattern of flow and channel morphology is quite different from typical patterns in meander bends, but is consistent with a conceptual model derived from laboratory experiments and numerical modeling.

Hydrogeology, geochemistry, and quality of water of The Basin and Oak Spring areas of the Chisos Mountains, Big Bend National Park, Texas

Science.gov (United States)

Baker, E.T.; Buszka, P.M.

1993-01-01

Test drilling near two sewage lagoons in The Basin area of the Chisos Mountains, Big Bend National Park, Texas, has shown that the alluvium and colluvium on which the lagoons are located is not saturated in the immediate vicinity of the lagoons. A shallow aquifer, therefore, does not exist in this critical area at and near the lagoons. Should seepage outflow from the lagoons occur, the effluent from the lagoons might eventually be incorporated into shallow ground water moving westward in the direction of Oak Spring. Under these conditions such water could reach the spring. Test borings that bottomed in bedrock below the alluvial and colluvial fill material are dry, indicating that no substantial leakage from the lagoons was detected. Therefore, no contaminant plume was identified. Fill material in The Basin does not contain water everywhere in its extensive outcropping area and supplies only a small quantity of ground water to Window Pouroff, which is the only natural surface outlet of The Basin.

Regional variation in the mechanical properties of the vertebral column during lateral bending in Morone saxatilis.

Science.gov (United States)

Nowroozi, B N; Brainerd, E L

2012-10-07

Unlike mammalian, disc-shaped intervertebral joints (IVJs), the IVJs in fishes are biconid structures, filled with fluid and thought to act as hydrostatic hinge joints during swimming. However, it remains unclear which IVJ structures are dominant in mechanical resistance to forces in fishes, and whether variation in these tissues might impact the function of the vertebral column along its length. Here, we measured the dynamic mechanical behaviour of IVJs from striped bass, Morone saxatilis. During lateral bending, angular stiffness was significantly lower in the caudal and cervical regions, relative to the abdominal region. The neutral zone, defined as the range of motion (ROM) at bending moments less than 0.001 Nm, was longer in the caudal relative to the abdominal IVJs. Hysteresis was 30-40% in all regions, suggesting that IVJs may play a role in energy dissipation during swimming. Cutting the vertical septum had no statistically significant effect, but cutting the encapsulating tissues caused a sharp decline in angular stiffness and a substantial increase in ROM and hysteresis. We conclude that stiffness decreases and ROM increases from cranial to caudal in striped bass, and that the encapsulating tissues play a prominent role in mechanical variation along the length of the vertebral column.

Geological, geochemical, and geophysical studies by the U.S. Geological Survey in Big Bend National Park, Texas

Science.gov (United States)

Page, W.R.; Turner, K.J.; Bohannon, R.G.; Berry, M.E.; Williams, V.S.; Miggins, D.P.; Ren, M.; Anthony, E.Y.; Morgan, L.A.; Shanks, P.W.C.; Gray, J. E.; Theodorakos, P.M.; Krabbenhoft, D. P.; Manning, A.H.; Gemery-Hill, P. A.; Hellgren, E.C.; Stricker, C.A.; Onorato, D.P.; Finn, C.A.; Anderson, E.; Gray, J. E.; Page, W.R.

2008-01-01

Big Bend National Park (BBNP), Tex., covers 801,163 acres (3,242 km2) and was established in 1944 through a transfer of land from the State of Texas to the United States. The park is located along a 118-mile (190-km) stretch of the Rio Grande at the United States-Mexico border. The park is in the Chihuahuan Desert, an ecosystem with high mountain ranges and basin environments containing a wide variety of native plants and animals, including more than 1,200 species of plants, more than 450 species of birds, 56 species of reptiles, and 75 species of mammals. In addition, the geology of BBNP, which varies widely from high mountains to broad open lowland basins, also enhances the beauty of the park. For example, the park contains the Chisos Mountains, which are dominantly composed of thick outcrops of Tertiary extrusive and intrusive igneous rocks that reach an altitude of 7,832 ft (2,387 m) and are considered the southernmost mountain range in the United States. Geologic features in BBNP provide opportunities to study the formation of mineral deposits and their environmental effects; the origin and formation of sedimentary and igneous rocks; Paleozoic, Mesozoic, and Cenozoic fossils; and surface and ground water resources. Mineral deposits in and around BBNP contain commodities such as mercury (Hg), uranium (U), and fluorine (F), but of these, the only significant mining has been for Hg. Because of the biological and geological diversity of BBNP, more than 350,000 tourists visit the park each year. The U.S. Geological Survey (USGS) has been investigating a number of broad and diverse geologic, geochemical, and geophysical topics in BBNP to provide fundamental information needed by the National Park Service (NPS) to address resource management goals in this park. Scientists from the USGS Mineral Resources and National Cooperative Geologic Mapping Programs have been working cooperatively with the NPS and several universities on several research studies within BBNP

A preliminary bending fatigue spectrum for steel monostrand cables

DEFF Research Database (Denmark)

Winkler, Jan; Fischer, Gregor; Georgakis, Christos T.

2011-01-01

This paper presents the results of the experimental study on the bending fatigue resistance of high-strength steel monostrand cables. From the conducted fatigue tests in the high-stress, low-cycle region, a preliminary bending fatigue spectrum is derived for the estimation of monostrand cable...... service life expectancy. The presented preliminary bending fatigue spectrum of high-strength monostrands is currently unavailable in the published literature. The presented results provide relevant information on the bending mechanism and fatigue characteristics of monostrand steel cables in tension...... and flexure and show that localized cable bending has a pronounced influence on the fatigue resistance of cables under dynamic excitations....

Bend measurement using an etched fiber incorporating a fiber Bragg grating.

Science.gov (United States)

Rauf, Abdul; Zhao, Jianlin; Jiang, Biqiang; Jiang, Yajun; Jiang, Wei

2013-01-15

A fiber Bragg grating (FBG) based bend measurement method using an etched fiber is proposed that utilizes the coupling of the core mode to the cladding and radiation modes at the bending region. An etching region of 99 µm diameter that serves as bend sensing head is achieved at 10 mm upstream the FBG through processing in 40% hydrofluoric acid, while the FBG acts as a narrowband reflector to enhance the sensitivity. The power variation curves are obtained for a wide range of bend angles, but the performance is limited due to the presence of the loss peaks. The sensing response is improved by immersing the etching region in a refractive index matching gel. The results are analyzed by using curve fitting formulas and are in good agreement. A large dynamic range of -27° to +27° and sensitivity of 0.43 dBm/deg is achieved, which can be enhanced by reducing the etched diameter.

Creep relaxation of fuel pin bending and ovalling stresses

International Nuclear Information System (INIS)

Chan, D.P.; Jackson, R.J.

1979-06-01

Analytical methods for calculating fuel pin cladding bending and ovalling stresses due to pin bundle-duct mechanical interaction taking into account nonlinear creep are presented. Calculated results are in close agreement with finite element results by MARC-CDC program. The methods are used to investigate the effect of creep on the FTR fuel cladding bending and ovalling stresses. It is concluded that the cladding of 316 SS 20% CW and reference design has high creep rates in the FTR core region to keep the bending and ovalling stresses to low levels

Recent big flare

International Nuclear Information System (INIS)

Moriyama, Fumio; Miyazawa, Masahide; Yamaguchi, Yoshisuke

1978-01-01

The features of three big solar flares observed at Tokyo Observatory are described in this paper. The active region, McMath 14943, caused a big flare on September 16, 1977. The flare appeared on both sides of a long dark line which runs along the boundary of the magnetic field. Two-ribbon structure was seen. The electron density of the flare observed at Norikura Corona Observatory was 3 x 10 12 /cc. Several arc lines which connect both bright regions of different magnetic polarity were seen in H-α monochrome image. The active region, McMath 15056, caused a big flare on December 10, 1977. At the beginning, several bright spots were observed in the region between two main solar spots. Then, the area and the brightness increased, and the bright spots became two ribbon-shaped bands. A solar flare was observed on April 8, 1978. At first, several bright spots were seen around the solar spot in the active region, McMath 15221. Then, these bright spots developed to a large bright region. On both sides of a dark line along the magnetic neutral line, bright regions were generated. These developed to a two-ribbon flare. The time required for growth was more than one hour. A bright arc which connects two ribbons was seen, and this arc may be a loop prominence system. (Kato, T.)

Ramifications of structural deformations on collapse loads of critically cracked pipe bends under in-plane bending and internal pressure

Energy Technology Data Exchange (ETDEWEB)

Sasidharan, Sumesh; Arunachalam, Veerappan; Subramaniam, Shanmugam [Dept. of Mechanical Engineering, National Institute of Technology, Tiruchirappalli (India)

2017-02-15

Finite-element analysis based on elastic-perfectly plastic material was conducted to examine the influence of structural deformations on collapse loads of circumferential through-wall critically cracked 90 .deg. pipe bends undergoing in-plane closing bending and internal pressure. The critical crack is defined for a through-wall circumferential crack at the extrados with a subtended angle below which there is no weakening effect on collapse moment of elbows subjected to in-plane closing bending. Elliptical and semioval cross sections were postulated at the bend regions and compared. Twice-elastic-slope method was utilized to obtain the collapse loads. Structural deformations, namely, ovality and thinning, were each varied from 0% to 20% in steps of 5% and the normalized internal pressure was varied from 0.2 to 0.6. Results indicate that elliptic cross sections were suitable for pipe ratios 5 and 10, whereas for pipe ratio 20, semioval cross sections gave satisfactory solutions. The effect of ovality on collapse loads is significant, although it cancelled out at a certain value of applied internal pressure. Thinning had a negligible effect on collapse loads of bends with crack geometries considered.

The Clinch Bend Regional Industrial Site and economic development opportunities

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-31

This effort focuses initially on the Clinch Bend site. Other sites and developable tracts of land are identified with the assistance of communities in proximity to Oak Ridge, the State of Tennessee, and others, and compared with the projected site requirements for large industrial facilities.

The effects of bending speed on the lumbo-pelvic kinematics and movement pattern during forward bending in people with and without low back pain.

Science.gov (United States)

Tsang, Sharon M H; Szeto, Grace P Y; Li, Linda M K; Wong, Dim C M; Yip, Millie M P; Lee, Raymond Y W

2017-04-17

Impaired lumbo-pelvic movement in people with low back pain during bending task has been reported previously. However, the regional mobility and the pattern of the lumbo-pelvic movement were found to vary across studies. The inconsistency of the findings may partly be related to variations in the speed at which the task was executed. This study examined the effects of bending speeds on the kinematics and the coordination lumbo-pelvic movement during forward bending, and to compare the performance of individuals with and without low back pain. The angular displacement, velocity and acceleration of the lumbo-pelvic movement during the repeated forward bending executed at five selected speeds were acquired using the three dimensional motion tracking system in seventeen males with low back pain and eighteen males who were asymptomatic. The regional kinematics and the degree of coordination of the lumbo-pelvic movement during bending was compared and analysed between two groups. Significantly compromised performance in velocity and acceleration of the lumbar spine and hip joint during bending task at various speed levels was shown in back pain group (p back pain group adopted a uniform lumbo-pelvic pattern across all the speed levels examined. The present findings show that bending speed imposes different levels of demand on the kinematics and pattern of the lumbo-pelvic movement. The ability to regulate the lumbo-pelvic movement pattern during the bending task that executed at various speed levels was shown only in pain-free individuals but not in those with low back pain. Individuals with low back pain moved with a stereotyped strategy at their lumbar spine and hip joints. This specific aberrant lumbo-pelvic movement pattern may have a crucial role in the maintenance of the chronicity in back pain.

Numerical analysis and optimization of 3D magnetohydrodynamic flows in rectangular U-bend

Energy Technology Data Exchange (ETDEWEB)

He, Qingyun, E-mail: hqingyun@mail.ustc.edu.cn; Feng, Jingchao; Chen, Hongli, E-mail: hlchen1@ustc.edu.cn

2016-11-01

Highlights: • MHD flows in rectangular U bends have been investigated under specific magnetic field. • U bends analyzed with different aspect ratio, distance of U bends and the wall conductance ratio. • Pressure optimization of rectangular U bends at corner region. • Studying different inclination of magnetic field cases according to original MHD flows. - Abstract: Liquid metal flow in rectangular bends is a common phenomenon of fusion liquid metal blanket operation, in which the velocity distributions and magnetohydrodynamic (MHD) pressure drop are considered as critical issues. Previous studies mainly aimed at specific fixed geometry for bend flows in LM blanket. The present investigation focuses on numerical analysis of MHD flow in 3D rectangular bends at laminar conditions, which is aimed to reduce MHD pressure drop caused by electromagnetic coupling in conductive flow, especially in bend corner region. The used code has been developed by University of Science and Technology of China (USTC) and validated by recommended benchmark cases such as Shercliff, ALEX experiments and KIT experiment cases, etc. In order to search the optimal duct bending, certain parameters such as different aspect ratio of the duct corner area cross-section, distance of import and export from the elbow and wall conductance ratio have been considered to investigate the pressure drop of MHD flow. Moreover, the effects of different magnetic field direction relative to flow distribution between bends have also been analyzed.

Numerical analysis and optimization of 3D magnetohydrodynamic flows in rectangular U-bend

International Nuclear Information System (INIS)

He, Qingyun; Feng, Jingchao; Chen, Hongli

2016-01-01

Highlights: • MHD flows in rectangular U bends have been investigated under specific magnetic field. • U bends analyzed with different aspect ratio, distance of U bends and the wall conductance ratio. • Pressure optimization of rectangular U bends at corner region. • Studying different inclination of magnetic field cases according to original MHD flows. - Abstract: Liquid metal flow in rectangular bends is a common phenomenon of fusion liquid metal blanket operation, in which the velocity distributions and magnetohydrodynamic (MHD) pressure drop are considered as critical issues. Previous studies mainly aimed at specific fixed geometry for bend flows in LM blanket. The present investigation focuses on numerical analysis of MHD flow in 3D rectangular bends at laminar conditions, which is aimed to reduce MHD pressure drop caused by electromagnetic coupling in conductive flow, especially in bend corner region. The used code has been developed by University of Science and Technology of China (USTC) and validated by recommended benchmark cases such as Shercliff, ALEX experiments and KIT experiment cases, etc. In order to search the optimal duct bending, certain parameters such as different aspect ratio of the duct corner area cross-section, distance of import and export from the elbow and wall conductance ratio have been considered to investigate the pressure drop of MHD flow. Moreover, the effects of different magnetic field direction relative to flow distribution between bends have also been analyzed.

Finite Element Analysis for Bending Process of U-Bending Specimens

Energy Technology Data Exchange (ETDEWEB)

Park, Won Dong; Bahn, Chi Bum [Pusan National University, Busan (Korea, Republic of)

2015-10-15

ASTM G30 suggests that the applied strain can be calculated by dividing thickness by a bend radius. It should be noted, however, that the formula is reliable under an assumption that the ratio of thickness to bend radius is less than 0.2. Typically, to increase the applied stress/strain, the ratio of thickness to bend radius becomes larger than 0.2. This suggests that the estimated strain values by ASTM G30 are not reliable to predict the actual residual strain state of the highly deformed U-bend specimen. For this reason, finite element analysis (FEA) for the bending process of Ubend specimens was conducted by using a commercial finite element analysis software ABAQUS. ver.6.14- 2;2014. From the results of FEA, PWSCC initiation time and U-bend specimen size can be determined exactly. Since local stress and strain have a significant effect on the initiation of PWSCC, it was inappropriate to apply results of ASTM G30 to the PWSCC test directly. According to results of finite element analysis (FEA), elastic relaxation can cause inaccuracy in intended final residual stress. To modify this inaccuracy, additional process reducing the spring back is required. However this additional process also may cause uncertainty of stress/strain state. Therefore, the U-bending specimen size which is not creating uncertainty should be optimized and selected. With the bending radius of 8.3 mm, the thickness of 3 mm and the roller distance of 32.6 mm, calculated maximum stress and strain were 670 MPa and 0.21, respectively.

In-plane and out-of-plane bending tests on carbon steel pipe bends

International Nuclear Information System (INIS)

Brouard, D.; Tremblais, A.; Vrillon, B.

1979-01-01

The objectives of these tests were to obtain experimental results on bends behaviour in elastic and plastic regime by in plane and out of plane bending. Results were used to improve the computer model, for large distorsion of bends, to be used in a simplified beam type computer code for piping calculations. Tests were made on type ANSI B 169 DN 5 bends in ASTM A 106 Grade B carbon steel. These tests made it possible to measure, for identical bends, in elastic regime, the flexibility factors and, in plastic regime, the total evolution in opening, in closing and out of plane. Flexibility factors of 180 0 bend without flanges are approximately the same in opening and in closing. The end effect due to flanges is not very significant, but it is important for 90 0 bends. In plastic regime, collapse loads or collapse moments of bends depends also of both the end effects and the angle bend. The end effects and the angle bend are more sensitive in opening than in closing. The interest of these tests is to procure some precise evolution curves of identical bends well characterized in geometry and metal strength, deflected in large distorsions. (orig./HP)

A Study on U-bending Technology using Rotary Draw Bending

Energy Technology Data Exchange (ETDEWEB)

Kwak, Ok-gyu; Kim, Won-seok [BHI Co., Gyunsang-Namdo (Korea, Republic of); Ku, Tae-wan [Pusan National Univ., Busan (Korea, Republic of)

2014-10-15

In the steam generator, heat transfer phenomenon for producing the steam between the primary system of the nuclear reactor and the secondary one occurs around the heat transfer tube. That is, the primary coolant with high temperature(320 .deg.. C) and high pressure(157Kgf/cm2) derived from the reactor flows in the heat transfer tube, and the secondary one runs out that tube. Therefore, it is able to mention that the heat transfer tube itself is a boundary of the heat transfer phenomenon. The heat transfer tube bundle of each steam generator used for the PWR and the PHWR(Pressurized Heavy Water Reactor) is generally composed of about 8,000-13,000 U-tubes. And these tubes are the core component as the structural and heat transfer material in the steam generator, which is in charge of cooling about 70% of the cooling surface of the primary system. For achieving the U-bending process with the thin walled tube, generally, a mandrel could be inserted in the tube according to the bending radius. But when the bending radius is small, the tube U-bending process could be also performed without the mandrel. In this study, numerical and experimental investigations on the U-bending process for producing the heat transfer tubes by using the straight and long tubes were carried out with the consideration of the elastic recovery after the U-bending. In the numerical approach, finite element analysis scheme was adopted with a commercial code, ABAQUS Implicit/Explicit. As the precedent study, the related experiment was also performed to verify the predicted results on the ovality and the minimum wall thickness of the U-bending heat transfer tube. Furthermore, its bending process was also conducted to analyze the deformation behavior for the Alloy 690 tube. In this study, the U-bending process was considered to simulate and manufactured the heat transfer tube used for the steam generator. To investigate the deformation behavior of the U-bending process, and a series of the

Adjustable Tooling for Bending Brake

Science.gov (United States)

Ellis, J. M.

1986-01-01

Deep metal boxes and other parts easily fabricated. Adjustable tooling jig for bending brake accommodates spacing blocks and either standard male press-brake die or bar die. Holds spacer blocks, press-brake die, bar window die, or combination of three. Typical bending operations include bending of cut metal sheet into box and bending of metal strip into bracket with multiple inward 90 degree bends. By increasing free space available for bending sheet-metal parts jig makes it easier to fabricate such items as deep metal boxes or brackets with right-angle bends.

A Numerical Study of the Spring-Back Phenomenon in Bending with a Rebar Bending Machine

Directory of Open Access Journals (Sweden)

Chang Hwan Choi

2014-10-01

Full Text Available Recently, the rebar bending methodology started to change from field processing to utilizing rebar bending machines at plant sites prior to transport to the construction locations. Computerized control of rebar plant bending machines provides more accurate and faster bending of rebars than the low quality inefficient field processing alternative. The bending process involves plastic deformation of rebars, where bending stress beyond the yield point of the material is applied. When the bending stress is removed, spring back is caused by the elastic restoring stress. Therefore, an accurate numerical analysis of the spring-back process is required to reduce the bending process errors. The most sensitive factors affecting the spring-back process are the bending radius, the bending angle, the diameter of the rebar, the friction coefficient, and the yielding strength of material. In this paper, we suggest a numerical modeling method using these factors. The finite element modeling of the dynamic mechanical behavior of the material during bending is performed using a commercial dynamic analysis program “DAFUL.” We use the least squares approach to derive the spring-back deflection as a function of the rebar bending parameters.

Big domains are novel Ca²+-binding modules: evidences from big domains of Leptospira immunoglobulin-like (Lig) proteins.

Science.gov (United States)

Raman, Rajeev; Rajanikanth, V; Palaniappan, Raghavan U M; Lin, Yi-Pin; He, Hongxuan; McDonough, Sean P; Sharma, Yogendra; Chang, Yung-Fu

2010-12-29

Many bacterial surface exposed proteins mediate the host-pathogen interaction more effectively in the presence of Ca²+. Leptospiral immunoglobulin-like (Lig) proteins, LigA and LigB, are surface exposed proteins containing Bacterial immunoglobulin like (Big) domains. The function of proteins which contain Big fold is not known. Based on the possible similarities of immunoglobulin and βγ-crystallin folds, we here explore the important question whether Ca²+ binds to a Big domains, which would provide a novel functional role of the proteins containing Big fold. We selected six individual Big domains for this study (three from the conserved part of LigA and LigB, denoted as Lig A3, Lig A4, and LigBCon5; two from the variable region of LigA, i.e., 9(th) (Lig A9) and 10(th) repeats (Lig A10); and one from the variable region of LigB, i.e., LigBCen2. We have also studied the conserved region covering the three and six repeats (LigBCon1-3 and LigCon). All these proteins bind the calcium-mimic dye Stains-all. All the selected four domains bind Ca²+ with dissociation constants of 2-4 µM. Lig A9 and Lig A10 domains fold well with moderate thermal stability, have β-sheet conformation and form homodimers. Fluorescence spectra of Big domains show a specific doublet (at 317 and 330 nm), probably due to Trp interaction with a Phe residue. Equilibrium unfolding of selected Big domains is similar and follows a two-state model, suggesting the similarity in their fold. We demonstrate that the Lig are Ca²+-binding proteins, with Big domains harbouring the binding motif. We conclude that despite differences in sequence, a Big motif binds Ca²+. This work thus sets up a strong possibility for classifying the proteins containing Big domains as a novel family of Ca²+-binding proteins. Since Big domain is a part of many proteins in bacterial kingdom, we suggest a possible function these proteins via Ca²+ binding.

Analytic description of the frictionally engaged in-plane bending process incremental swivel bending (ISB)

Science.gov (United States)

Frohn, Peter; Engel, Bernd; Groth, Sebastian

2018-05-01

Kinematic forming processes shape geometries by the process parameters to achieve a more universal process utilizations regarding geometric configurations. The kinematic forming process Incremental Swivel Bending (ISB) bends sheet metal strips or profiles in plane. The sequence for bending an arc increment is composed of the steps clamping, bending, force release and feed. The bending moment is frictionally engaged by two clamping units in a laterally adjustable bending pivot. A minimum clamping force hindering the material from slipping through the clamping units is a crucial criterion to achieve a well-defined incremental arc. Therefore, an analytic description of a singular bent increment is developed in this paper. The bending moment is calculated by the uniaxial stress distribution over the profiles' width depending on the bending pivot's position. By a Coulomb' based friction model, necessary clamping force is described in dependence of friction, offset, dimensions of the clamping tools and strip thickness as well as material parameters. Boundaries for the uniaxial stress calculation are given in dependence of friction, tools' dimensions and strip thickness. The results indicate that changing the bending pivot to an eccentric position significantly affects the process' bending moment and, hence, clamping force, which is given in dependence of yield stress and hardening exponent. FE simulations validate the model with satisfactory accordance.

Investigation of collisional effects within the bending magnet region of a DIII-D neutral beamline

International Nuclear Information System (INIS)

Kessler, D.N.; Hong, R.; Kellman, D.H.

1993-10-01

The region between the pole faces of the DIII-D neutral beamline residual ion bending magnets is an area of transient high gas pressure which may cause beam defocusing and increased heating of beamline internal components due to collisional effects. An investigation of these effects helps in understanding residual ion trajectories and in providing information for studying in the beamline capability for operation with increased pulse duration. Examination of collisional effects, and of the possible existence of space charge blow-up, was carried out by injecting deuterium gas into the region between the magnet pole faces with rates varying from 0 to 18 torr-ell/sec. Thermocouple and waterflow calorimetry data were taken to measure the beamline component heating and beam powder deposition on the magnet pole shields, magnet louvers, ion dump, beam collimators, and calorimeter. Data was also taken at gas flow rates varying from 0 to 25 torr-ell/sec into the neutralizer cell and is compared with the magnet region gas injection data obtained. Results show that both collisional effects and space charge blow-up play a role in magnet region component heating and that neutralizer gas flow sufficiently reduces component heating without incurring unacceptable power losses through collisional effects

Closed-form plastic collapse loads of pipe bends under combined pressure and in-plane bending

International Nuclear Information System (INIS)

Oh, Chang Sik; Kim, Yun Jae

2006-01-01

Based on three-dimensional (3-D) FE limit analyses, this paper provides plastic limit, collapse and instability load solutions for pipe bends under combined pressure and in-plane bending. The plastic limit loads are determined from FE limit analyses based on elastic-perfectly plastic materials using the small geometry change option, and the FE limit analyses using the large geometry change option provide plastic collapse loads (using the twice-elastic-slope method) and instability loads. For the bending mode, both closing bending and opening bending are considered, and a wide range of parameters related to the bend geometry is considered. Based on the FE results, closed-form approximations of plastic limit and collapse load solutions for pipe bends under combined pressure and bending are proposed

Analytical investigation in bending characteristic of twisted stacked-tape cable conductor

International Nuclear Information System (INIS)

Takayasu, Makoto; Chiesa, Luisa

2015-01-01

An analytical model to evaluate bending strains of a twisted stack-tape cable (TSTC) conductor has been developed. Through a comparison with experimental results obtained for a soldered 32-tape YBCO TSTC conductor, it has been found that a Perfect-Slip Model (PSM) taking into account the slipping between tapes in a stacked-tape cable during bending gives much better estimation of the bending performance compared to a No-Slip Model (NSM). In the PSM case the tapes can slip so that the internal longitudinal axial strain can be released. The longitudinal strains of compression and tension regions along the tape are balanced in one twist-pitch and cancel out evenly in a long cable. Therefore, in a cable the strains due to bending can be minimized. This is an important advantage of a TSTC conductor. The effect of the cable diameter size on the bending strain is also expected to be minor, and all tapes composing a TSTC conductor have the same strain response under bending, therefore the cable critical current can be characterized from a single tape behaviour. (paper)

Analytical investigation in bending characteristic of twisted stacked-tape cable conductor

Science.gov (United States)

Takayasu, Makoto; Chiesa, Luisa

2015-12-01

An analytical model to evaluate bending strains of a twisted stack-tape cable (TSTC) conductor has been developed. Through a comparison with experimental results obtained for a soldered 32-tape YBCO TSTC conductor, it has been found that a Perfect-Slip Model (PSM) taking into account the slipping between tapes in a stacked-tape cable during bending gives much better estimation of the bending performance compared to a No-Slip Model (NSM). In the PSM case the tapes can slip so that the internal longitudinal axial strain can be released. The longitudinal strains of compression and tension regions along the tape are balanced in one twist-pitch and cancel out evenly in a long cable. Therefore, in a cable the strains due to bending can be minimized. This is an important advantage of a TSTC conductor. The effect of the cable diameter size on the bending strain is also expected to be minor, and all tapes composing a TSTC conductor have the same strain response under bending, therefore the cable critical current can be characterized from a single tape behaviour.

Do asparagine-linked carbohydrate chains in glycoproteins have a preference for beta-bends?

NARCIS (Netherlands)

Beintema, Jaap J.

X-ray structures of the conformation of carbohydrate moieties and connected regions of glycoproteins are summarized. Evidence is presented that there is some preference for carbohydrate attachment at β-bends. Evolution may have favored glycosylation to occur at bends to ensure free mobility of the

Plastic loads of pipe bends under combined pressure and out-of-plane bending

International Nuclear Information System (INIS)

Lee, Kuk Hee; Kim, Yun Jae; Park, Chi Yong; Lee, Sung Ho; Kim, Tae Ryong

2007-01-01

Based on three-Dimensional (3-D) FE limit analyses, this paper provides plastic limit and TES(Twice- Elastic-Slope) loads for pipe bends under combined pressure and out-of-plane bending. The plastic limit loads are determined from FE limit analyses based on elastic.perfectly-plastic materials using the small geometry change option, and the FE limit analyses using the large geometry change option provide TES plastic loads. A wide range of parameters related to the bend geometry is considered. Based on the FE results, closed-form approximations of plastic limit and TES plastic load solutions for pipe bends under out-of-plane bending are proposed

Secondary flow in sharp open-channel bends

NARCIS (Netherlands)

Blanckaert, K.; De Vriend, H.J.

2004-01-01

Secondary currents are a characteristic feature of flow in open-channel bends. Besides the classical helical motion (centre-region cell), a weaker and smaller counter-rotating circulation cell (outer-bank cell) is often observed near the outer bank, which is believed to play an important role in

Big Sites, Big Questions, Big Data, Big Problems: Scales of Investigation and Changing Perceptions of Archaeological Practice in the Southeastern United States

Directory of Open Access Journals (Sweden)

Cameron B Wesson

2014-08-01

Full Text Available Since at least the 1930s, archaeological investigations in the southeastern United States have placed a priority on expansive, near-complete, excavations of major sites throughout the region. Although there are considerable advantages to such large–scale excavations, projects conducted at this scale are also accompanied by a series of challenges regarding the comparability, integrity, and consistency of data recovery, analysis, and publication. We examine the history of large–scale excavations in the southeast in light of traditional views within the discipline that the region has contributed little to the ‘big questions’ of American archaeology. Recently published analyses of decades old data derived from Southeastern sites reveal both the positive and negative aspects of field research conducted at scales much larger than normally undertaken in archaeology. Furthermore, given the present trend toward the use of big data in the social sciences, we predict an increased use of large pre–existing datasets developed during the New Deal and other earlier periods of archaeological practice throughout the region.

Estimates of plastic loads for pipe bends under combined in-plane and out-of-plane bending moment

International Nuclear Information System (INIS)

Kim, Nak Hyun; Oh, Chang Sik; Kim, Yun Jae

2008-01-01

This paper provides a method to estimate plastic loads (defined by twice-elastic-slope) for pipe bends under combined in-plane and out-of-plane bending moment, based on detailed 3-D FE limit analyses using elastic-perfectly plastic materials. Because closing bending moment is always lower than opening bending moment, the combination of in-plane closing bending and out-of-plane bending moment becomes the most significant case. Due to conservatism of each bending moments, the resultant moment provided by ASME B and PV code is unduly conservative. However, the concept of the resultant moment is still valid. In this paper, FE results show that the accurate solutions of bending moments provide better estimates of plastic loads of pipe bend under combined in-plane bending and out-of-plane bending moment

The effect of load-controlled bending load on the failure pressure of wall-thinned pipe elbows

International Nuclear Information System (INIS)

Kim, Jin Weon; Yoon, Min Soo; Park, Chi Yong

2013-01-01

Highlights: • We evaluated bending load effect on the failure pressure of wall-thinned pipe elbows. • Burst tests were conducted on real-scale elbow specimens with local wall thinning. • The tests were performed under combined pressure and load-controlled bending. • Load-controlled bending reduced the failure pressure of wall-thinned elbows. • Bending load effect was significant for opening-mode and intrados wall-thinning case. - Abstract: In this research, burst tests were conducted on real-scale elbow specimens, each with an artificial local wall-thinning defect, under combined internal pressure and constant in-plane bending load, as well as under simple internal pressure, to evaluate the effect of load-controlled bending load on the failure pressure of locally wall-thinned pipe elbows. Ninety-degree, 65A Schedule 80 elbows, with wall-thinning defects in the intrados and extrados, were used as specimens. The bending loads were in-plane opening- and closing-mode bending, applied in load-control mode. The results clearly indicated that a load-controlled in-plane bending load reduced the failure pressure of wall-thinned pipe elbows, in contrast to observations previously made under displacement-controlled bending conditions. The effect of the bending load was more significant for opening-mode than for closing-mode bending, regardless of the wall-thinning location in the elbow. Also, the effect was greater when the wall-thinning defect was located in the intrados region of the elbow, rather than the extrados region. Existing models that have been proposed to evaluate the failure of wall-thinned elbows under simple internal pressure conservatively predicted the failure pressure of elbows subjected to a combined internal pressure and load-controlled bending load

Big domains are novel Ca²+-binding modules: evidences from big domains of Leptospira immunoglobulin-like (Lig proteins.

Directory of Open Access Journals (Sweden)

Rajeev Raman

Full Text Available BACKGROUND: Many bacterial surface exposed proteins mediate the host-pathogen interaction more effectively in the presence of Ca²+. Leptospiral immunoglobulin-like (Lig proteins, LigA and LigB, are surface exposed proteins containing Bacterial immunoglobulin like (Big domains. The function of proteins which contain Big fold is not known. Based on the possible similarities of immunoglobulin and βγ-crystallin folds, we here explore the important question whether Ca²+ binds to a Big domains, which would provide a novel functional role of the proteins containing Big fold. PRINCIPAL FINDINGS: We selected six individual Big domains for this study (three from the conserved part of LigA and LigB, denoted as Lig A3, Lig A4, and LigBCon5; two from the variable region of LigA, i.e., 9(th (Lig A9 and 10(th repeats (Lig A10; and one from the variable region of LigB, i.e., LigBCen2. We have also studied the conserved region covering the three and six repeats (LigBCon1-3 and LigCon. All these proteins bind the calcium-mimic dye Stains-all. All the selected four domains bind Ca²+ with dissociation constants of 2-4 µM. Lig A9 and Lig A10 domains fold well with moderate thermal stability, have β-sheet conformation and form homodimers. Fluorescence spectra of Big domains show a specific doublet (at 317 and 330 nm, probably due to Trp interaction with a Phe residue. Equilibrium unfolding of selected Big domains is similar and follows a two-state model, suggesting the similarity in their fold. CONCLUSIONS: We demonstrate that the Lig are Ca²+-binding proteins, with Big domains harbouring the binding motif. We conclude that despite differences in sequence, a Big motif binds Ca²+. This work thus sets up a strong possibility for classifying the proteins containing Big domains as a novel family of Ca²+-binding proteins. Since Big domain is a part of many proteins in bacterial kingdom, we suggest a possible function these proteins via Ca²+ binding.

Platonic scattering cancellation for bending waves in a thin plate

KAUST Repository

Farhat, Mohamed

2014-04-10

We propose an ultra-thin elastic cloak to control the scattering of bending waves in isotropic heterogeneous thin plates. The cloak design makes use of the scattering cancellation technique applied, for the first time, to the biharmonic operator describing the propagation of bending waves in thin plates. We first analyze scattering from hard and soft cylindrical objects in the quasistatic limit, then we prove that the scattering of bending waves from an object in the near and far-field regions can be suppressed significantly by covering it with a suitably designed coating. Beyond camouflaging, these findings may have potential applications in protection of buildings from earthquakes and isolating structures from vibrations in the motor vehicle industry.

Platonic scattering cancellation for bending waves in a thin plate

KAUST Repository

Farhat, Mohamed; Chen, P.-Y.; Bagci, Hakan; Enoch, S.; Guenneau, S.; Alù , A.

2014-01-01

We propose an ultra-thin elastic cloak to control the scattering of bending waves in isotropic heterogeneous thin plates. The cloak design makes use of the scattering cancellation technique applied, for the first time, to the biharmonic operator describing the propagation of bending waves in thin plates. We first analyze scattering from hard and soft cylindrical objects in the quasistatic limit, then we prove that the scattering of bending waves from an object in the near and far-field regions can be suppressed significantly by covering it with a suitably designed coating. Beyond camouflaging, these findings may have potential applications in protection of buildings from earthquakes and isolating structures from vibrations in the motor vehicle industry.

Recent developments in bend-insensitive and ultra-bend-insensitive fibers

Science.gov (United States)

Boivin, David; de Montmorillon, Louis-Anne; Provost, Lionel; Montaigne, Nelly; Gooijer, Frans; Aldea, Eugen; Jensma, Jaap; Sillard, Pierre

2010-02-01

Designed to overcome the limitations in case of extreme bending conditions, Bend- and Ultra-Bend-Insensitive Fibers (BIFs and UBIFs) appear as ideal solutions for use in FTTH networks and in components, pigtails or patch-cords for ever demanding applications such as military or sensing. Recently, however, questions have been raised concerning the Multi-Path-Interference (MPI) levels in these fibers. Indeed, they are potentially subject to interferences between the fundamental mode and the higher-order mode that is also bend resistant. This MPI is generated because of discrete discontinuities such as staples, bends and splices/connections that occur on distance scales that become comparable to the laser coherent length. In this paper, we will demonstrate the high MPI tolerance of all-solid single-trench-assisted BIFs and UBIFs. We will present the first comprehensive study combining theoretical and experimental points of view to quantify the impact of fusion splices on coherent MPI. To be complete, results for mechanical splices will also be reported. Finally, we will show how the single-trench- assisted concept combined with the versatile PCVD process allows to tightly control the distributions of fibers characteristics. Such controls are needed to massively produce BIFs and to meet the more stringent specifications of the UBIFs.

Yield stress determination from miniaturized disk bend test data

International Nuclear Information System (INIS)

Sohn, D.S.; Kohse, G.; Harling, O.K.

1985-04-01

Methodology for testing 3.0 mm diameter by 0.25 mm thick disks by bending in a punch and die has been described previously. This paper describes the analysis of load/deflection data from such miniaturized disk bend tests (MDBT) using a finite element simulation. Good simulation has been achieved up to a point just beyond the predominantly elastic response, linear initial region. The load at which deviation from linearity begins has been found to correlate with yield stress, and yield stress has been successfully extracted from disk bend tests of a number of known materials. Although finite element codes capable of dealing with large strains and large rotations have been used, simulation of the entire load/deflection curve up to fracture of the specimen has not yet been achieved

Experimental and Numerical Investigations of Applying Tip-bottomed Tool for Bending Advanced Ultra-high Strength Steel Sheet

Science.gov (United States)

Mitsomwang, Pusit; Borrisutthekul, Rattana; Klaiw-awoot, Ken; Pattalung, Aran

2017-09-01

This research was carried out aiming to investigate the application of a tip-bottomed tool for bending an advanced ultra-high strength steel sheet. The V-die bending experiment of a dual phase steel (DP980) sheet which had a thickness of 1.6 mm was executed using a conventional bending and a tip-bottomed punches. Experimental results revealed that the springback of the bent worksheet in the case of the tip-bottomed punch was less than that of the conventional punch case. To further discuss bending characteristics, a finite element (FE) model was developed and used to simulate the bending of the worksheet. From the FE analysis, it was found that the application of the tip-bottomed punch contributed the plastic deformation to occur at the bending region. Consequently, the springback of the worksheet reduced. In addition, the width of the punch tip was found to affect the deformation at the bending region and determined the springback of the bent worksheet. Moreover, the use of the tip-bottomed punch resulted in the apparent increase of the surface hardness of the bent worksheet, compared to the bending with the conventional punch.

Big Data and Regional Science: Opportunities, Challenges, and Directions for Future Research

OpenAIRE

Schintler, Laurie A.; Fischer, Manfred M.

2018-01-01

Recent technological, social, and economic trends and transformations are contributing to the production of what is usually referred to as Big Data. Big Data, which is typically defined by four dimensions -- Volume, Velocity, Veracity, and Variety -- changes the methods and tactics for using, analyzing, and interpreting data, requiring new approaches for data provenance, data processing, data analysis and modeling, and knowledge representation. The use and analysis of Big Data involves severa...

Occipital bending in schizophrenia.

Science.gov (United States)

Maller, Jerome J; Anderson, Rodney J; Thomson, Richard H; Daskalakis, Zafiris J; Rosenfeld, Jeffrey V; Fitzgerald, Paul B

2017-01-01

To investigate the prevalence of occipital bending (an occipital lobe crossing or twisting across the midline) in subjects with schizophrenia and matched healthy controls. Occipital bending prevalence was investigated in 37 patients with schizophrenia and 44 healthy controls. Ratings showed that prevalence was nearly three times higher among schizophrenia patients (13/37 [35.1%]) than in control subjects (6/44 [13.6%]). Furthermore, those with schizophrenia had greater normalized gray matter volume but less white matter volume and had larger brain-to-cranial ratio. The results suggest that occipital bending is more prevalent among schizophrenia patients than healthy subjects and that schizophrenia patients have different gray matter-white matter proportions. Although the cause and clinical ramifications of occipital bending are unclear, the results infer that occipital bending may be a marker of psychiatric illness.

The effects of encapsulating C60 fullerenes on the bending flexibility of carbon nanotubes

International Nuclear Information System (INIS)

Zhu, J; Pan, Z Y; Wang, Y X; Zhou, L; Jiang, Q

2007-01-01

We investigate the bending flexibility of carbon nanotubes (CNTs) with encapsulated C 60 fullerenes, using molecular dynamics (MD) simulations. Our simulations on the bending of the fully ((C 60 ) 12 -(10,10)) and partially ((C 60 ) 10 -(10,10)) filled peapods show an 18 and 6.3% increase of the flexural rigidity, and a 45 and 11% increase of the buckling strength, respectively, compared to the empty (10, 10) CNT. What is characteristically different for the peapod from the empty CNT is the presence of a transitional region in the loading process that proceeds to the onset of buckling. Within this transitional region, the interaction between the encapsulated fullerenes and the hosting CNT leads to an unusual configuration of the peapod, in which there are ripples along the inner arc of the bent peapod. The transition region in the partially filled peapod is short compared with the fully filled peapod. This is mainly caused by the axial motion of C 60 fullerenes, especially after the appearance of the small ripple. The rippling configuration has been reported previously in the bending of multi-walled CNTs, where it emerges after the critical bending angle. However, in the present case, the peapod remains perfectly elastic in this transitional region until buckling takes place

Theory of magnetoelectric effect in multilayer nanocomposites on a substrate: Static bending-mode response

Directory of Open Access Journals (Sweden)

Matthias C. Krantz

2013-02-01

Full Text Available Magnetoelectric (ME coefficients for bending excitation in static magnetic fields and the bending response of multilayer composites with alternating magnetostrictive (MS and piezoelectric (PE layers on a substrate are investigated systematically. Theory and closed-form analytic solutions for the static magnetoelectric and the bending response coefficients are presented. Results of systematic variation of layer numbers, layer sequences, PE volume fractions, substrate thicknesses, and four different material systems (employing FeCoBSi, Terfenol-D, AlN, PZT, and Si are given for a fixed total composite thickness of 5μm. Among more than 105 structures investigated the greatest static ME coefficient of 62.3 V/cmOe is predicted for all odd layer number FeCoBSi-AlN multilayer composites on a Si substrate at vanishing substrate thickness and a PE material fraction of 38%. Varying the substrate thickness from 0μm to 20μm and the PE fraction from 0% to 100%, broad parameter regions of high ME coefficients are found for odd and large layer number nanocomposites. These regions are further enhanced to narrow maxima at vanishing substrate thickness, which correspond to structures of vanishing static bending response. For bilayers and even layer number cases broad maxima of the ME coefficient are observed at nonzero substrates and bending response. The optimal layer sequence and PE fraction depend on the material system. Bending response maxima occur at zero Si substrate thickness and nonzero PE fractions for bilayers. For multilayers nonzero Si substrates and zero PE fractions are found to be optimal. Structures of even ME layer numbers of PE-MS...Sub layer sequence display regions of vanishing bending response with large ME coefficients, i.e., produced by longitudinal excitation.

Field Investigation of Flow Structure and Channel Morphology at Confluent-Meander Bends

Science.gov (United States)

Riley, J. D.; Rhoads, B. L.

2007-12-01

The movement of water and sediment through drainage networks is inevitably influenced by the convergence of streams and rivers at channel confluences. These focal components of fluvial systems produce a complex hydrodynamic environment, where rapid changes in flow structure and sediment transport occur to accommodate the merging of separate channel flows. The inherent geometric and hydraulic change at confluences also initiates the development of distinct geomorphic features, reflected in the bedform and shape of the channel. An underlying assumption of previous experimental and theoretical models of confluence dynamics has been that converging streams have straight channels with angular configurations. This generalized conceptualization was necessary to establish confluence planform as symmetrical or asymmetrical and to describe subsequent flow structure and geomorphic features at confluences. However, natural channels, particularly those of meandering rivers, curve and bend. This property and observation of channel curvature at natural junctions have led to the hypothesis that natural stream and river confluences tend to occur on the concave outer bank of meander bends. The resulting confluence planform, referred to as a confluent-meander bend, was observed over a century ago but has received little scientific attention. This paper examines preliminary data on three-dimensional flow structure and channel morphology at two natural confluent-meander bends of varying size and with differing tributary entrance locations. The large river confluence of the Vermilion River and Wabash River in west central Indiana and the comparatively small junction of the Little Wabash River and Big Muddy Creek in southeastern Illinois are the location of study sites for field investigation. Measurements of time-averaged three-dimensional velocity components were obtained at these confluences with an acoustic Doppler current profiler for flow events with differing momentum ratios. Bed

Vertebrate richness and biogeography in the Big Thicket of Texas

Science.gov (United States)

Michael H MacRoberts; Barbara R. MacRoberts; D. Craig Rudolph

2010-01-01

The Big Thicket of Texas has been described as rich in species and a “crossroads:” a place where organisms from many different regions meet. We examine the species richness and regional affiliations of Big Thicket vertebrates. We found that the Big Thicket is neither exceptionally rich in vertebrates nor is it a crossroads for vertebrates. Its vertebrate fauna is...

Big data analytics turning big data into big money

CERN Document Server

Ohlhorst, Frank J

2012-01-01

Unique insights to implement big data analytics and reap big returns to your bottom line Focusing on the business and financial value of big data analytics, respected technology journalist Frank J. Ohlhorst shares his insights on the newly emerging field of big data analytics in Big Data Analytics. This breakthrough book demonstrates the importance of analytics, defines the processes, highlights the tangible and intangible values and discusses how you can turn a business liability into actionable material that can be used to redefine markets, improve profits and identify new business opportuni

Bending the law: tidal bending and its effects on ice viscosity and flow

Science.gov (United States)

Rosier, S.; Gudmundsson, G. H.

2017-12-01

Many ice shelves are subject to strong ocean tides and, in order to accommodate this vertical motion, the ice must bend within the grounding zone. This tidal bending generates large stresses within the ice, changing its effective viscosity. For a confined ice shelf, this is particularly relevant because the tidal bending stresses occur along the sidewalls, which play an important role in the overall flow regime of the ice shelf. Hence, tidal bending stresses will affect both the mean and time-varying components of ice shelf flow. GPS measurements reveal strong variations in horizontal ice shelf velocities at a variety of tidal frequencies. We show, using full-Stokes viscoelastic modelling, that inclusion of tidal bending within the model accounts for much of the observed tidal modulation of horizontal ice shelf flow. Furthermore, our model shows that in the absence of a vertical tidal forcing, the mean flow of the ice shelf is reduced considerably.

Big Opportunities and Big Concerns of Big Data in Education

Science.gov (United States)

Wang, Yinying

2016-01-01

Against the backdrop of the ever-increasing influx of big data, this article examines the opportunities and concerns over big data in education. Specifically, this article first introduces big data, followed by delineating the potential opportunities of using big data in education in two areas: learning analytics and educational policy. Then, the…

Fracture probability properties of pure and cantilever bending fatigue of STS304 steel

International Nuclear Information System (INIS)

Roh, Sung Kuk; Park, Dae Hyun; Jeong, Soon Uk

2001-01-01

Big accidents of flyings, vessel, subways, gas equipments, buildings and bridge happens frequently. Therefore many people are suffering harm of property. The destruction cause of marcaine components is almost accused by fatigue. This study is test for STS304 specimen using pure and cantilever bending state. Rounded and notched specimen including fracture surface investigation was comparatively experimented, fatigue life according to degree of surface finishing was examined. Fatigue fracture probability of notched canilever specimens were predicted by P-S-N curve, median rank and Weibull distribution. And at the relation with the rotational speed and stress, the fatigue life of the test specimen was higher at high speed than low speed

A New Kind of Bend Sensor

Institute of Scientific and Technical Information of China (English)

无

2000-01-01

A new kind of bend sensor is introduced.It can be used to detect the bend angle of an object or inclination between two objects.It has characteristics of small size, lightweight, high reliability, fine flexibility and plasticity.When this bend sensor is used with a proper converting circuit, it can implement dynamic measuring the bend angle of an object conveniently.The application of the bend sensor in dataglove is also described.

The creep bending of short radius pipe bends

International Nuclear Information System (INIS)

Spence, John

1975-01-01

In existing and proposed liquid metal fast breeder reactor design the pipework has considerable importance. Parts of the LMFBR include thin walled short radius bends which are expected to operate in the creep regime. In linear elasticity it is known that the assumption of long radius bends is not too severe as far as the flexibility characteristics are concerned although some modifications are necessary for accurate determination of the stresses. No data exists for nonlinear creep. Current work is aimed at elucidating the effect of the various assumptions common to linear elastic theory in so far as they affect the creep characteristics of bends on systems. Herein an energy based analysis using a simple n power constitutive law for stationary creep is employed to derive basic design data for flexibilities and stresses which will be necessary before complete systems can be assessed for creep. The analysis shows on comparison with the long radius work that the assumption of R>r is not much more restrictive in creep than for linear elasticity. Flexibilities for short radius bends appear to be well approximated by the long radius values. Thus the attractive reference stress information already derived may be used directly to find deformations without a complete knowledge of the constitutive relationship. However, stresses are somewhat different. Fortunately the maximum deviation occurs at relatively low levels of stress, the peak stresses being in fair agreement. When n=1 the present results reduce essentially to those obtained from existing linear elastic theory

Differences in Spontaneous Intracerebral Hemorrhage Cases between Urban and Rural Regions of Taiwan: Big Data Analytics of Government Open Data.

Science.gov (United States)

Ting, Hsien-Wei; Chien, Ting-Ying; Lai, K Robert; Pan, Ren-Hao; Wu, Kuan-Hsien; Chen, Jun-Min; Chan, Chien-Lung

2017-12-10

This study evaluated the differences in spontaneous intracerebral hemorrhage (sICH) between rural and urban areas of Taiwan with big data analysis. We used big data analytics and visualization tools to examine government open data, which included the residents' health medical administrative data, economic status, educational status, and relevant information. The study subjects included sICH patients of Taipei region (29,741 cases) and Eastern Taiwan (4565 cases). The incidence of sICH per 100,000 population per year in Eastern Taiwan (71.3 cases) was significantly higher than that of the Taipei region (42.3 cases). The mean coverage area per hospital in Eastern Taiwan (452.4 km²) was significantly larger than the Taipei region (24 km²). The residents educational level in the Taipei region was significantly higher than that in Eastern Taiwan. The mean hospital length of stay in the Taipei region (17.9 days) was significantly greater than that in Eastern Taiwan (16.3 days) ( p < 0.001). There were no significant differences in other medical profiles between two areas. Distance and educational barriers were two possible reasons for the higher incidence of sICH in the rural area of Eastern Taiwan. Further studies are necessary in order to understand these phenomena in greater depth.

Differences in Spontaneous Intracerebral Hemorrhage Cases between Urban and Rural Regions of Taiwan: Big Data Analytics of Government Open Data

Directory of Open Access Journals (Sweden)

Hsien-Wei Ting

2017-12-01

Full Text Available This study evaluated the differences in spontaneous intracerebral hemorrhage (sICH between rural and urban areas of Taiwan with big data analysis. We used big data analytics and visualization tools to examine government open data, which included the residents’ health medical administrative data, economic status, educational status, and relevant information. The study subjects included sICH patients of Taipei region (29,741 cases and Eastern Taiwan (4565 cases. The incidence of sICH per 100,000 population per year in Eastern Taiwan (71.3 cases was significantly higher than that of the Taipei region (42.3 cases. The mean coverage area per hospital in Eastern Taiwan (452.4 km2 was significantly larger than the Taipei region (24 km2. The residents educational level in the Taipei region was significantly higher than that in Eastern Taiwan. The mean hospital length of stay in the Taipei region (17.9 days was significantly greater than that in Eastern Taiwan (16.3 days (p < 0.001. There were no significant differences in other medical profiles between two areas. Distance and educational barriers were two possible reasons for the higher incidence of sICH in the rural area of Eastern Taiwan. Further studies are necessary in order to understand these phenomena in greater depth.

Pilot Studies of Geologic and Terrestrial Carbon Sequestration in the Big Sky Region, USA, and Opportunities for Commercial Scale Deployment of New Technologies

Science.gov (United States)

Waggoner, L. A.; Capalbo, S. M.; Talbott, J.

2007-05-01

Within the Big Sky region, including Montana, Idaho, South Dakota, Wyoming and the Pacific Northwest, industry is developing new coal-fired power plants using the abundant coal and other fossil-based resources. Of crucial importance to future development programs are robust carbon mitigation plans that include a technical and economic assessment of regional carbon sequestration opportunities. The objective of the Big Sky Carbon Sequestration Partnership (BSCSP) is to promote the development of a regional framework and infrastructure required to validate and deploy carbon sequestration technologies. Initial work compiled sources and potential sinks for carbon dioxide (CO2) in the Big Sky Region and developed the online Carbon Atlas. Current efforts couple geologic and terrestrial field validation tests with market assessments, economic analysis and regulatory and public outreach. The primary geological efforts are in the demonstration of carbon storage in mafic/basalt formations, a geology not yet well characterized but with significant long-term storage potential in the region and other parts of the world; and in the Madison Formation, a large carbonate aquifer in Wyoming and Montana. Terrestrial sequestration relies on management practices and technologies to remove atmospheric CO2 to storage in trees, plants, and soil. This indirect sequestration method can be implemented today and is on the front-line of voluntary, market-based approaches to reduce CO2 emissions. Details of pilot projects are presented including: new technologies, challenges and successes of projects and potential for commercial-scale deployment.

Limit loads for pipe bends under combined pressure and in-plane bending based on finite element limit analysis

International Nuclear Information System (INIS)

Oh, Chang Sik; Kim, Yun Jae

2006-01-01

In the present paper, approximate plastic limit load solutions for pipe bends under combined internal pressure and bending are obtained from detailed three-dimensional (3-D) FE limit analyses based on elastic-perfectly plastic materials with the small geometry change option. The present FE results show that existing limit load solutions for pipe bends are lower bounds but can be very different from the present FE results in some cases, particularly for bending. Accordingly closed-form approximations are proposed for pipe bends under combined pressure and in-plane bending based on the present FE results. The proposed limit load solutions would be a basis of defective pipe bends and be useful to estimate non-linear fracture mechanics parameters based on the reference stress approach

The big data-big model (BDBM) challenges in ecological research

Science.gov (United States)

Luo, Y.

2015-12-01

The field of ecology has become a big-data science in the past decades due to development of new sensors used in numerous studies in the ecological community. Many sensor networks have been established to collect data. For example, satellites, such as Terra and OCO-2 among others, have collected data relevant on global carbon cycle. Thousands of field manipulative experiments have been conducted to examine feedback of terrestrial carbon cycle to global changes. Networks of observations, such as FLUXNET, have measured land processes. In particular, the implementation of the National Ecological Observatory Network (NEON), which is designed to network different kinds of sensors at many locations over the nation, will generate large volumes of ecological data every day. The raw data from sensors from those networks offer an unprecedented opportunity for accelerating advances in our knowledge of ecological processes, educating teachers and students, supporting decision-making, testing ecological theory, and forecasting changes in ecosystem services. Currently, ecologists do not have the infrastructure in place to synthesize massive yet heterogeneous data into resources for decision support. It is urgent to develop an ecological forecasting system that can make the best use of multiple sources of data to assess long-term biosphere change and anticipate future states of ecosystem services at regional and continental scales. Forecasting relies on big models that describe major processes that underlie complex system dynamics. Ecological system models, despite great simplification of the real systems, are still complex in order to address real-world problems. For example, Community Land Model (CLM) incorporates thousands of processes related to energy balance, hydrology, and biogeochemistry. Integration of massive data from multiple big data sources with complex models has to tackle Big Data-Big Model (BDBM) challenges. Those challenges include interoperability of multiple

Accessibility of the pre-big-bang models to LIGO

International Nuclear Information System (INIS)

Mandic, Vuk; Buonanno, Alessandra

2006-01-01

The recent search for a stochastic background of gravitational waves with LIGO interferometers has produced a new upper bound on the amplitude of this background in the 100 Hz region. We investigate the implications of the current and future LIGO results on pre-big-bang models of the early Universe, determining the exclusion regions in the parameter space of the minimal pre-big-bang scenario. Although the current LIGO reach is still weaker than the indirect bound from big bang nucleosynthesis, future runs by LIGO, in the coming year, and by Advanced LIGO (∼2009) should further constrain the parameter space, and in some parts surpass the Big Bang nucleosynthesis bound. It will be more difficult to constrain the parameter space in nonminimal pre-big bang models, which are characterized by multiple cosmological phases in the yet not well understood stringy phase, and where the higher-order curvature and/or quantum-loop corrections in the string effective action should be included

Testing machine for fatigue crack kinetic investigation in specimens under bending

International Nuclear Information System (INIS)

Panasyuk, V.V.; Ratych, L.V.; Dmytrakh, I.N.

1978-01-01

A kinematic diagram of testing mashine for the investigation of fatigue crack kinetics in prismatic specimens, subjected to pure bending is described. Suggested is a technique of choosing an optimum ratio of the parameters of ''the testing machine-specimen'' system, which provide the stabilization of the stress intensity coefficient for a certain region of crack development under hard loading. On the example of the 40KhS and 15Kh2MFA steel specimens the pliability of the machine constructed according to the described diagram and designed for the 30ONxm maximum bending moment. The results obtained can be used in designing of the testing machines for studying pure bending under hard loading and in choosing the sizes of specimens with rectangular cross sections for investigations into the kinetics of the fatigue crack

Methodology for definition of bending radius and pullback force in HDD (Horizontal Directional Drilling) operations

Energy Technology Data Exchange (ETDEWEB)

Silva, Danilo Machado L. da; Rodrigues, Marcos V. [Det Norske Veritas (DNV), Rio de Janeiro, RJ (Brazil); Venaas, Asle [Det Norske Veritas (DNV), Oslo (Norway); Medeiros, Antonio Roberto de [Subsea 7 (Brazil)

2009-12-19

Bending is a primary loading experienced by pipelines during installation and operation. Significant bending in the presence of tension is experienced during installation by the S-lay method, as the pipe conforms to the curvature of the stinger and beyond in the over bend region. Bending in the presence of external pressure is experienced in the sag bend of all major installation methods (e.g., reeling, J-lay, S-lay) as well as in free-spans on the sea floor. Bending is also experienced by pipelines during installation by horizontal directional drilling. HDD procedures are increasingly being utilized around the world not only for crossings of rivers and other obstacles but also for shore approach of offshore pipelines. During installation the pipeline experience a combination of tensile, bending, and compressive stresses. The magnitude of these stresses is a function of the approach angle, bending radius, pipe diameter, length of the borehole, and the soil properties at the site. The objective of this paper is to present an overview of some aspects related to bending of the product pipe during HDD operations, which is closely related to the borehole path as the pipeline conforms to the curvature of the hole. An overview of the aspects related to tensile forces is also presented. The combined effect of bending and tensile forces during the pullback operation is discussed. (author)

Numerical simulation of liquid-metal-flows in radial-toroidal-radial bends

International Nuclear Information System (INIS)

Molokov, S.; Buehler, L.

1993-09-01

Magnetohydrodynamic flows in a U-bend and right-angle bend are considered with reference to the radial-toroidal-radial concept of a self-cooled liquid-metal blanket. The ducts composing bends have rectangular cross-section. The applied magnetic field is aligned with the toroidal duct and perpendicular to the radial ones. At high Hartmann number the flow region is divided into cores and boundary layers of different types. The magnetohydrodynamic equations are reduced to a system of partial differential equations governing wall electric potentials and the core pressure. The system is solved numerically by two different methods. The first method is iterative with iteration between wall potential and the core pressure. The second method is a general one for the solution of the core flow equations in curvilinear coordinates generated by channel geometry and magnetic field orientation. Results obtained are in good agreement. They show, that the 3D-pressure drop of MHD flows in a U-bend is not a critical issue for blanket applications. (orig./HP) [de

Parameters design of the dielectric elastomer spring-roll bending actuator (Conference Presentation)

Science.gov (United States)

Li, Jinrong; Liu, Liwu; Liu, Yanju; Leng, Jinsong

2017-04-01

Dielectric elastomers are novel soft smart material that could deform sustainably when subjected to external electric field. That makes dielectric elastomers promising materials for actuators. In this paper, a spring-roll actuator that would bend when a high voltage is applied was fabricated based on dielectric elastomer. Using such actuators as active parts, the flexible grippers and inchworm-inspired crawling robots were manufactured, which demonstrated some examples of applications in soft robotics. To guide the parameters design of dielectric elastomer based spring-roll bending actuators, the theoretical model of such actuators was established based on thermodynamic theories. The initial deformation and electrical induced bending angle of actuators were formulated. The failure of actuators was also analyzed considering some typical failure modes like electromechanical instability, electrical breakdown, loss of tension and maximum tolerant stretch. Thus the allowable region of actuators was determined. Then the bending angle-voltage relations and failure voltages of actuators with different parameters, including stretches of the dielectric elastomer film, number of active layers, and dimensions of spring, were investigated. The influences of each parameter on the actuator performances were discussed, providing meaningful guidance to the optical design of the spring-roll bending actuators.

Rupture prediction for induction bends under opening mode bending with emphasis on strain localization

International Nuclear Information System (INIS)

Mitsuya, Masaki; Sakanoue, Takashi

2015-01-01

This study focuses on the opening mode of induction bends; this mode represents the deformation outside a bend. Bending experiments on induction bends are shown and the manner of failure of these bends was investigated. Ruptures occur at the intrados of the bends, which undergo tensile stress, and accompany the local reduction of wall thickness, i.e., necking that indicates strain localization. By implementing finite element analysis (FEA), it was shown that the rupture is dominated not by the fracture criterion of material but by the initiation of strain localization that is a deformation characteristic of the material. These ruptures are due to the rapid increase of local strain after the initiation of strain localization and suddenly reach the fracture criterion. For the evaluation of the deformability of the bends, a method based on FEA that can predict the displacement at the rupture is proposed. We show that the yield surface shape and the true stress–strain relationship after uniform elongation have to be defined on the basis of the actual properties of the bend material. The von Mises yield criterion, which is commonly used in cases of elastic–plastic FEA, could not predict the rupture and overestimated the deformability. In contrast, a yield surface obtained by performing tensile tests on a biaxial specimen could predict the rupture. The prediction of the rupture was accomplished by an inverse calibration method that determined the true stress-strain relationship after uniform elongation. As an alternative to the inverse calibration, a simple extrapolation method of the true stress-strain relationship after uniform elongation which can predict the rupture is proposed. - Highlights: • A method based on FEA that can predict the displacement at the rupture is proposed. • The yield surface shape and the true stress–strain have to be defined precisely. • The von Mises yield criterion overestimated the deformability. • The ruptures are due to the

Bend me, shape me

CERN Multimedia

2002-01-01

A Japanese team has found a way to bend and shape silicon substrates by growing a thin layer of diamond on top. The technique has been proposed as an alternative to mechanical bending, which is currently used to make reflective lenses for X-ray systems and particle physics systems (2 paragraphs).

Investigation of bending fatigue-life of aluminum sheets based on rolling direction

Directory of Open Access Journals (Sweden)

Raif Sakin

2018-03-01

Full Text Available High-cycle fatigue (HCF and low-cycle fatigue (LCF fatigue lives of rolled AA1100 and AA1050 aluminum sheets along different directions were evaluated at room temperature. Four types of samples denoted as longitudinal (L and transverse (T to the rolling direction were compared because the samples along the two typical directions show an obvious anisotropy. A cantilever plane-bending and multi-type fatigue testing machine was specially designed for this purpose. Deflection-controlled fatigue tests were conducted under fully reversed loading. The longest fatigue lives in the LCF region were obtained for AA1050 (L while AA1100 (L samples had the longest fatigue lives in the HCF region. Keywords: AA1100, AA1050, Aluminum sheet, Bending fatigue life, Rolling direction

On the accuracy of analyses for in-plane bending of smooth pipe bends with end constraints

International Nuclear Information System (INIS)

Thomson, G.; Spence, J.

1985-01-01

The accuracy of theoretical analyses for in-plane bending of smooth pipebends with end constraints is discussed and investigated with a view to explaining and reducing the differences between the major works. An earlier theory of the authors is improved to give more accurate answers for bends with rigid flanges. Flanged bends are then examined in some detail, quantifying for the first time the important influence of the flange rigidity on the bend flexibility and stresses. A summary of some finite element analyses is presented from which it is clear that further work is desirable. (orig.)

Effect of bend separation distance on the mass transfer in back-to-back pipe bends arranged in a 180° configuration

Science.gov (United States)

Chen, X.; Le, T.; Ewing, D.; Ching, C. Y.

2016-12-01

The mass transfer to turbulent flow through back-to-back pipe bends arranged in a 180° configuration with different lengths of pipe between the bends was measured using a dissolving gypsum test section in water. The measurements were performed for bends with a radius of curvature of 1.5 times the pipe diameter ( D) at a Reynolds numbers of 70,000 and Schmidt number of 1280. The maximum mass transfer in the bends decreased from approximately 1.8 times the mass transfer in the upstream pipe when there was no separation distance between the bends to 1.7 times when there was a 1 D or 5 D length of pipe between the bends. The location of the maximum mass transfer was on the inner sidewall downstream of the second bend when there was no separation distance between the bends. This location changed to the inner wall at the beginning of the second bend when there was a 1 D long pipe between the bends, and to the inner sidewall at the end of the first bend when there was a 5 D long pipe between the bends.

Bend testing for miniature disks

International Nuclear Information System (INIS)

Huang, F.H.; Hamilton, M.L.; Wire, G.L.

1982-01-01

A bend test was developed to obtain ductility measurements on a large number of alloy variants being irradiated in the form of miniature disks. Experimental results were shown to be in agreement with a theoretical analysis of the bend configuration. Disk specimens fabricated from the unstrained grip ends of previously tested tensile specimens were used for calibration purposes; bend ductilities and tensile ductilities were in good agreement. The criterion for estimating ductility was judged acceptable for screening purposes

Fabrication of topology optimized photonic crystal waveguide Z-bend displaying large bandwidth with very low bend loss

DEFF Research Database (Denmark)

Harpøth, Anders; Frandsen, Lars Hagedorn; Kristensen, Martin

2004-01-01

We have designed, simulated and fabricated a photonic crystal waveguide Z-bend, which displays a total bend loss of ~1dB per bend in a wavelength range of more than 200nm. The fabricated component performs in excellent agreement with 3D finite-difference time-domain calculations....

Measurements of emittance growth through the achromatic bend at the BNL Accelerator Test Facility

International Nuclear Information System (INIS)

Wang, X.J.; Kehne, D.

1997-07-01

Measurements of emittance growth in a high peak current beam as it passes through an achromatic double bend are summarized. Experiments were performed using the ATF at Brookhaven National Laboratory by X.J. Wang and D. Kehne as a collaboration resulting from the proposal attached at the end of the document. The ATF consists off an RF gun (1 MeV), two sections of linac (40-75 MeV), a diagnostic section immediately following the linac, a 20 degree bend magnet, a variable aperture slit at a high dispersion point, 5 quadrupoles, then another 20 degree bend followed by another diagnostic section. The TRANSPORT deck describing the region from the end of the linac to the end of the diagnostic line following the achromatic bends is attached to the end of this document. Printouts of the control screens are also attached

How Big Are "Martin's Big Words"? Thinking Big about the Future.

Science.gov (United States)

Gardner, Traci

"Martin's Big Words: The Life of Dr. Martin Luther King, Jr." tells of King's childhood determination to use "big words" through biographical information and quotations. In this lesson, students in grades 3 to 5 explore information on Dr. King to think about his "big" words, then they write about their own…

76 FR 81992 - PPL Bell Bend, LLC; Combined License Application for Bell Bend Nuclear Power Plant; Exemption

Science.gov (United States)

2011-12-29

... License Application for Bell Bend Nuclear Power Plant; Exemption 1.0 Background PPL Bell Bend, LLC... for Nuclear Power Plants.'' This reactor is to be identified as Bell Bend Nuclear Power Plant (BBNPP... based upon the U.S. EPR reference COL (RCOL) application for UniStar's Calvert Cliffs Nuclear Power...

Residual stresses in U-bending deformations and expansion joints of heat exchanger tubes

International Nuclear Information System (INIS)

Kim, Woo Gon; Kim, Sun Jae; Jang, Jin Sung; Kuk, Ii Hiun; Bae, Kang Gug; Kim, Sung Chung

2000-01-01

Residual stress induced in U-bending and tube-to-tubesheet joint processes of PWR's rew-1 heat exchanger tube was measured by X-ray method and Hole-Drilling Method(HDM). Compressive residual stresses(-) at the extrados surface were induced in U-bending, and its maximum value reached -319MPa in axial direction at the position of ψ=0 deg. Tensile residual stresses (+) of 0σ zz =45 MPa and σ θθ =25MPa were introduced in the intrados surface at the position of ψ=0 deg. Maximum tensile residual stress of 170 MPa was measured at the flank side at the position of ψ=90 deg, i.e., at apex region. It was observed that higher stress gradient was generated at the irregular transition regions (ITR). The trend of residual stress induced by U-bending process of the tubes was found to be related with the change of ovality. The residual stress induced by the explosive joint method was found to be lower than that by the mechanical roll method. The gradient of residual stress along the expanded tube was highest at the transition region (TR), and the residual stress in circumferential direction was found to be higher than the residual stress in axial direction

A transparent bending-insensitive pressure sensor

Science.gov (United States)

Lee, Sungwon; Reuveny, Amir; Reeder, Jonathan; Lee, Sunghoon; Jin, Hanbit; Liu, Qihan; Yokota, Tomoyuki; Sekitani, Tsuyoshi; Isoyama, Takashi; Abe, Yusuke; Suo, Zhigang; Someya, Takao

2016-05-01

Measuring small normal pressures is essential to accurately evaluate external stimuli in curvilinear and dynamic surfaces such as natural tissues. Usually, sensitive and spatially accurate pressure sensors are achieved through conformal contact with the surface; however, this also makes them sensitive to mechanical deformation (bending). Indeed, when a soft object is pressed by another soft object, the normal pressure cannot be measured independently from the mechanical stress. Here, we show a pressure sensor that measures only the normal pressure, even under extreme bending conditions. To reduce the bending sensitivity, we use composite nanofibres of carbon nanotubes and graphene. Our simulations show that these fibres change their relative alignment to accommodate bending deformation, thus reducing the strain in individual fibres. Pressure sensitivity is maintained down to a bending radius of 80 μm. To test the suitability of our sensor for soft robotics and medical applications, we fabricated an integrated sensor matrix that is only 2 μm thick. We show real-time (response time of ∼20 ms), large-area, normal pressure monitoring under different, complex bending conditions.

D-branes in a big bang/big crunch universe: Nappi-Witten gauged WZW model

Energy Technology Data Exchange (ETDEWEB)

Hikida, Yasuaki [School of Physics and BK-21 Physics Division, Seoul National University, Seoul 151-747 (Korea, Republic of); Nayak, Rashmi R. [Dipartimento di Fisica and INFN, Sezione di Roma 2, ' Tor Vergata' ' , Rome 00133 (Italy); Panigrahi, Kamal L. [Dipartimento di Fisica and INFN, Sezione di Roma 2, ' Tor Vergata' , Rome 00133 (Italy)

2005-05-01

We study D-branes in the Nappi-Witten model, which is a gauged WZW model based on (SL(2,R) x SU(2))/(U(1) x U(1)). The model describes a four dimensional space-time consisting of cosmological regions with big bang/big crunch singularities and static regions with closed time-like curves. The aim of this paper is to investigate by D-brane probes whether there are pathologies associated with the cosmological singularities and the closed time-like curves. We first classify D-branes in a group theoretical way, and then examine DBI actions for effective theories on the D-branes. In particular, we show that D-brane metric from the DBI action does not include singularities, and wave functions on the D-branes are well behaved even in the presence of closed time-like curves.

Research on Design and Simulation of Biaxial Tensile-Bending Complex Mechanical Performance Test Apparatus

Directory of Open Access Journals (Sweden)

Hailian Li

2017-09-01

Full Text Available In order to realize a micro-mechanic performance test of biaxial tensile-bending-combined loading and solve the problem of incompatibility of test apparatus and observation apparatus, novel biaxial-combined tensile-bending micro-mechanical performance test apparatus was designed. The working principle and major functions of key constituent parts of test apparatus, including the servo drive unit, clamping unit and test system, were introduced. Based on the finite element method, biaxial tensile and tension-bending-combined mechanical performances of the test-piece were studied as guidance to learn the distribution of elastic deformation and plastic deformation of all sites of the test-piece and to better plan test regions. Finally, this test apparatus was used to conduct a biaxial tensile test under different pre-bending loading and a tensile test at different rates; the image of the fracture of the test-piece was acquired by a scanning electron microscope and analyzed. It was indicated that as the pre-bending force rises, the elastic deformation phase would gradually shorten and the slope of the elastic deformation phase curve would slightly rise so that a yield limit would appear ahead of time. Bending speed could exert a positive and beneficial influence on tensile strength but weaken fracture elongation. If bending speed is appropriately raised, more ideal anti-tensile strength could be obtained, but fracture elongation would decline.

Big Data, Big Problems: A Healthcare Perspective.

Science.gov (United States)

Househ, Mowafa S; Aldosari, Bakheet; Alanazi, Abdullah; Kushniruk, Andre W; Borycki, Elizabeth M

2017-01-01

Much has been written on the benefits of big data for healthcare such as improving patient outcomes, public health surveillance, and healthcare policy decisions. Over the past five years, Big Data, and the data sciences field in general, has been hyped as the "Holy Grail" for the healthcare industry promising a more efficient healthcare system with the promise of improved healthcare outcomes. However, more recently, healthcare researchers are exposing the potential and harmful effects Big Data can have on patient care associating it with increased medical costs, patient mortality, and misguided decision making by clinicians and healthcare policy makers. In this paper, we review the current Big Data trends with a specific focus on the inadvertent negative impacts that Big Data could have on healthcare, in general, and specifically, as it relates to patient and clinical care. Our study results show that although Big Data is built up to be as a the "Holy Grail" for healthcare, small data techniques using traditional statistical methods are, in many cases, more accurate and can lead to more improved healthcare outcomes than Big Data methods. In sum, Big Data for healthcare may cause more problems for the healthcare industry than solutions, and in short, when it comes to the use of data in healthcare, "size isn't everything."

Occipital bending in depression.

Science.gov (United States)

Maller, Jerome J; Thomson, Richard H S; Rosenfeld, Jeffrey V; Anderson, Rodney; Daskalakis, Zafiris J; Fitzgerald, Paul B

2014-06-01

There are reports of differences in occipital lobe asymmetry within psychiatric populations when compared with healthy control subjects. Anecdotal evidence and enlarged lateral ventricles suggests that there may also be a different pattern of curvature whereby one occipital lobe wraps around the other, termed 'occipital bending'. We investigated the prevalence of occipital bending in 51 patients with major depressive disorder (males mean age = 41.96 ± 14.00 years, females mean age = 40.71 ± 12.41 years) and 48 age- and sex-matched healthy control subjects (males mean age = 40.29 ± 10.23 years, females mean age = 42.47 ± 14.25 years) and found the prevalence to be three times higher among patients with major depressive disorder (18/51, 35.3%) when compared with control subjects (6/48, 12.5%). The results suggest that occipital bending is more common among patients with major depressive disorder than healthy subjects, and that occipital asymmetry and occipital bending are separate phenomena. Incomplete neural pruning may lead to the cranial space available for brain growth being restricted, or ventricular enlargement may exacerbate the natural occipital curvature patterns, subsequently causing the brain to become squashed and forced to 'wrap' around the other occipital lobe. Although the clinical implications of these results are unclear, they provide an impetus for further research into the relevance of occipital bending in major depression disorder. © The Author (2014). Published by Oxford University Press on behalf of the Guarantors of Brain. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Big Surveys, Big Data Centres

Science.gov (United States)

Schade, D.

2016-06-01

Well-designed astronomical surveys are powerful and have consistently been keystones of scientific progress. The Byurakan Surveys using a Schmidt telescope with an objective prism produced a list of about 3000 UV-excess Markarian galaxies but these objects have stimulated an enormous amount of further study and appear in over 16,000 publications. The CFHT Legacy Surveys used a wide-field imager to cover thousands of square degrees and those surveys are mentioned in over 1100 publications since 2002. Both ground and space-based astronomy have been increasing their investments in survey work. Survey instrumentation strives toward fair samples and large sky coverage and therefore strives to produce massive datasets. Thus we are faced with the "big data" problem in astronomy. Survey datasets require specialized approaches to data management. Big data places additional challenging requirements for data management. If the term "big data" is defined as data collections that are too large to move then there are profound implications for the infrastructure that supports big data science. The current model of data centres is obsolete. In the era of big data the central problem is how to create architectures that effectively manage the relationship between data collections, networks, processing capabilities, and software, given the science requirements of the projects that need to be executed. A stand alone data silo cannot support big data science. I'll describe the current efforts of the Canadian community to deal with this situation and our successes and failures. I'll talk about how we are planning in the next decade to try to create a workable and adaptable solution to support big data science.

Recht voor big data, big data voor recht

NARCIS (Netherlands)

Lafarre, Anne

Big data is een niet meer weg te denken fenomeen in onze maatschappij. Het is de hype cycle voorbij en de eerste implementaties van big data-technieken worden uitgevoerd. Maar wat is nu precies big data? Wat houden de vijf V's in die vaak genoemd worden in relatie tot big data? Ter inleiding van

A missing-bending-magnet scheme for PEP

International Nuclear Information System (INIS)

Liu, R.Z.; Winick, H.

1988-01-01

This article presents a missing-bending-magnet scheme for PEP as a modification that could be considered if PEP were available as a fully dedicated synchrotron radiation source. The scheme can be applied to one or more PEP sextants without changing the rest. By removing some bending magnets, rearranging the remaining magnets, and adding two quadrupoles, ten additional straight sections per sextant can be created, each 5 m or more in length, for insertion devices. Beam lines therefrom, plus possible beam lines from bending magnets would enter a continuous experimental hall instead of individual tunnels and halls for each beam line. This should result in construction cost savings and increased operations efficiency. The ideal beam orbit is unchanged at the two ends and the middle of the sextant. At the end of the curved part of the sextant the lattice functions match those of the long interaction region straight section in the low emittance configuration of PEP. The electron beam characteristics in the newly created straight sections are described, including the enlargement of the horizontal beam size due to the nonzero dispersion. Some disadvantages of the scheme are increased operations complexity due to the need for nine new quadrupole families, increased beam emittance (by 14.5% is one sextant is modified), and reduced dynamic aperture. However, the dynamic aperture is still about as large as the physical aperture and should be adequate for good beam lifetime and injection. (orig.)

NUMERICAL PREDICTION OF COMPOSITE BEAM SUBJECTED TO COMBINED NEGATIVE BENDING AND AXIAL TENSION

Directory of Open Access Journals (Sweden)

MAHESAN BAVAN

2013-08-01

Full Text Available The present study has investigated the finite element method (FEM techniques of composite beam subjected to combined axial tension and negative bending. The negative bending regions of composite beams are influenced by worsen failures due to various levels of axial tensile loads on steel section especially in the regions near internal supports. Three dimensional solid FEM model was developed to accurately predict the unfavourable phenomenon of cracking of concrete and compression of steel in the negative bending regions of composite beam due to axial tensile loads. The prediction of quasi-static solution was extensively analysed with various deformation speeds and energy stabilities. The FEM model was then validated with existing experimental data. Reasonable agreements were observed between the results of FEM model and experimental analysis in the combination of vertical-axial forces and failure modes on ultimate limit state behaviour. The local failure modes known as shear studs failure, excess yielding on steel beam and crushing on concrete were completely verified by extensive similarity between the numerical and experimental results. Finally, a proper way of modelling techniques for large FEM models by considering uncertainties of material behaviour due to biaxial loadings and complex contact interactions is discussed. Further, the model is suggested for the limit state prediction of composite beam with calibrating necessary degree of the combined axial loads.

Magnetic design considerations for the SSC vertical bending (BV1C) magnet

International Nuclear Information System (INIS)

Venkatraman, V.; Goodzeit, C.; Jayakumar, R.; Nobrega, F.; Snitchler, G.

1994-01-01

The BV1C magnet is a large aperture, vertical bending magnet to be used to bend proton beams in the interaction region. An aperture larger than 80 mm is required. The central field has to be a minimum of 6T with a 10% margin. The lattice requirements for field quality are stringent because two counter beams traverse this magnet off the center axis. This magnet's transfer function sag is specified to match closely the transfer function sag of the low beta quadrupoles. With these specifications in mind, suitable designs for the 2-D magnetic cross-sections have been analyzed

Reliability of non-heated tube bends of boilers

International Nuclear Information System (INIS)

Bugaj, N.V.; Akhremenko, V.L.; Zamotaev, V.S.

1984-01-01

Bend failures are described for non-heated boiler tubes of 12Kh1MF and 20 steels. Methods of reliability evaluations are presented which permit revealing and replacing the bends with inadequate resources. Influences of operation conditions on bend durability is shown as well as the factors which are dominating at bend failures

Bending sound in graphene: Origin and manifestation

Energy Technology Data Exchange (ETDEWEB)

Adamyan, V.M., E-mail: vadamyan@onu.edu.ua [Department of Theoretical Physics, Odessa I.I. Mechnikov National University, 2 Dvoryanska St., Odessa 65026 (Ukraine); Bondarev, V.N., E-mail: bondvic@onu.edu.ua [Department of Theoretical Physics, Odessa I.I. Mechnikov National University, 2 Dvoryanska St., Odessa 65026 (Ukraine); Zavalniuk, V.V., E-mail: vzavalnyuk@onu.edu.ua [Department of Theoretical Physics, Odessa I.I. Mechnikov National University, 2 Dvoryanska St., Odessa 65026 (Ukraine); Department of Fundamental Sciences, Odessa Military Academy, 10 Fontanska Road, Odessa 65009 (Ukraine)

2016-11-11

Highlights: • The origin of sound-like dispersion of graphene bending mode is disclosed. • The speed of graphene bending sound is determined. • The renormalized graphene bending rigidity is derived. • The intrinsic corrugations of graphene are estimated. - Abstract: It is proved that the acoustic-type dispersion of bending mode in graphene is generated by the fluctuation interaction between in-plane and out-of-plane terms in the free energy arising with account of non-linear components in the graphene strain tensor. In doing so we use an original adiabatic approximation based on the alleged (confirmed a posteriori) significant difference of sound speeds for in-plane and bending modes. The explicit expression for the bending sound speed depending only on the graphene mass density, in-plane elastic constants and temperature is deduced as well as the characteristics of the microscopic corrugations of graphene. The obtained results are in good quantitative agreement with the data of real experiments and computer simulations.

Bending sound in graphene: Origin and manifestation

International Nuclear Information System (INIS)

Adamyan, V.M.; Bondarev, V.N.; Zavalniuk, V.V.

2016-01-01

Highlights: • The origin of sound-like dispersion of graphene bending mode is disclosed. • The speed of graphene bending sound is determined. • The renormalized graphene bending rigidity is derived. • The intrinsic corrugations of graphene are estimated. - Abstract: It is proved that the acoustic-type dispersion of bending mode in graphene is generated by the fluctuation interaction between in-plane and out-of-plane terms in the free energy arising with account of non-linear components in the graphene strain tensor. In doing so we use an original adiabatic approximation based on the alleged (confirmed a posteriori) significant difference of sound speeds for in-plane and bending modes. The explicit expression for the bending sound speed depending only on the graphene mass density, in-plane elastic constants and temperature is deduced as well as the characteristics of the microscopic corrugations of graphene. The obtained results are in good quantitative agreement with the data of real experiments and computer simulations.

Formulation of Forming Load in V-Bending

Directory of Open Access Journals (Sweden)

Koumura Yuki

2016-01-01

Full Text Available A novel method is described to calculate the forming load in V-bending by a press brake. The data of forming load are collected by FEM analysis. With an increase of the punch stroke in V-bending, the forming load increases gradually after the elastic limit, and then decreases after showing the maximum value. The proposal formulation to trace the variations in the forming load curve includes the calculating method of the load of the elastic limit, the maximum load in air bending and the variations of the forming load before/after the bending stroke of the maximum load. The calculated precision is confirmed by comparing with the measured load-stroke curves in V-bending with a press brake.

NURE aerial gamma-ray and magnetic reconnaissance survey: Big Bend area, Marfa MH 13-5, Fort Stockton MH 13-6, Presidio MH 13-8, Emory Peak MH 13-9 Quadrangles. Volume I. Narrative report

International Nuclear Information System (INIS)

1979-02-01

A rotary-wing, reconnaissance, high sensitivity, radiometric and magnetic survey was performed in the Big Bend area of Texas. Four 1:250,000 scale NTMS quadrangles (Marfa, Ft. Stockton, Presidio, and Emory Peak) were surveyed. A total of 7,529 line miles (12,115 kilometers) of data were collected utilizing a Sikorsky S58T helicopter. Traverse lines were flown in an east-west direction at 3.0 mile (5 kilometer) spacing, with tie lines flown in a north-south direction at 12.5 mile (20 kilometer) spacing. The data were digitally recorded at 1.0 second intervals. The NaI terrestrial detectors used in this survey had a total volume of 2,154 cubic inches. The magnetometer employed was a modified ASQ-10 fluxgate system. The radiometric data was normalized to 400 feet terrain clearance and is presented in the form of computer listings on microfiche and as stacked profile plots. Profile plots are contained in Volume II of this report. A geologic interpretation of the radiometric and magnetic data is included as part of this report

A numerical simulation of pre-big bang cosmology

CERN Document Server

Maharana, J P; Veneziano, Gabriele

1998-01-01

We analyse numerically the onset of pre-big bang inflation in an inhomogeneous, spherically symmetric Universe. Adding a small dilatonic perturbation to a trivial (Milne) background, we find that suitable regions of space undergo dilaton-driven inflation and quickly become spatially flat ($\\Omega \\to 1$). Numerical calculations are pushed close enough to the big bang singularity to allow cross checks against previously proposed analytic asymptotic solutions.

Permanent bending and alignment of ZnO nanowires

Energy Technology Data Exchange (ETDEWEB)

Borschel, Christian; Spindler, Susann; Oertel, Michael; Ronning, Carsten [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Max-Wien-Platz 1, 07743 Jena (Germany); Lerose, Damiana [MPI fuer Mikrostrukturphysik, Weinberg 2, 06120 Halle/Saale (Germany); Institut fuer Photonische Technologien, Albert-Einstein-Strasse 9, 07745 Jena (Germany); Bochmann, Arne [Institut fuer Photonische Technologien, Albert-Einstein-Strasse 9, 07745 Jena (Germany); Christiansen, Silke H. [Institut fuer Photonische Technologien, Albert-Einstein-Strasse 9, 07745 Jena (Germany); MPI fuer die Physik des Lichts, Guenther-Scharowsky-Str. 1, 91058 Erlangen (Germany); Nietzsche, Sandor [Zentrum fuer Elektronenmikroskopie, Friedrich-Schiller-Universitaet Jena, Ziegelmuehlenweg 1, 07743 Jena (Germany)

2011-07-01

Ion beams can be used to bend or re-align nanowires permanently, after they have been grown. We have irradiated ZnO nanowires with ions of different species and energy, achieving bending and alignment in various directions. We study the bending of single nanowires as well as the simultaneous alignment of large ensembles of ZnO nanowires in detail. Computer simulations show that the bending is initiated by ion beam induced damage. Dislocations are identified to relax stresses and make the bending and alignment permanent and resistant against annealing procedures.

Structural analysis of suerconducting bending magnets

International Nuclear Information System (INIS)

Meuser, R.B.

1980-05-01

Mechanical stresses, displacements, and the effects of displacements upon aberrations of the magnetic field in the aperture have been calculated for a class of superconducting bending-magnet configurations. The analytical model employed for the coil is one in which elements are free to slide without restraint upon each other, and upon the surrounding structure. Coil configurations considered range from an idealized one in which the current density varies as cosine theta to more realistic ones consisting of regions of uniform current density. With few exceptions, the results for the more realistic coils closely match those of the cos theta coil

Matter sources for a null big bang

International Nuclear Information System (INIS)

Bronnikov, K A; Zaslavskii, O B

2008-01-01

We consider the properties of stress-energy tensors compatible with a null big bang, i.e., cosmological evolution starting from a Killing horizon rather than a singularity. For Kantowski-Sachs cosmologies, it is shown that if matter satisfies the null energy condition, then (i) regular cosmological evolution can only start from a Killing horizon, (ii) matter is absent at the horizon and (iii) matter can only appear in the cosmological region due to interaction with vacuum. The latter is understood phenomenologically as a fluid whose stress tensor is insensitive to boosts in a particular direction. We also argue that matter is absent in a static region beyond the horizon. All this generalizes the observations recently obtained for a mixture of dust and a vacuum fluid. If, however, we admit the existence of phantom matter, its certain special kinds (with the parameter w ≤ -3) are consistent with a null big bang without interaction with vacuum (or without vacuum fluid at all). Then in the static region there is matter with w ≥ -1/3. Alternatively, the evolution can begin from a horizon in an infinitely remote past, leading to a scenario combining the features of a null big bang and an emergent universe

Strength tests of thin-walled elliptic duralumin cylinders in pure bending and in combined pure bending and torsion

Science.gov (United States)

Lundquist, Eugene E; Stowell, Elbridge Z

1942-01-01

An analysis is presented of the results of tests made by the Massachusetts Institute of Technology and by the National Advisory Committee for Aeronautics on an investigation of the strength of thin-walled circular and elliptic cylinders in pure bending and in combined torsion and bending. In each of the loading conditions, the bending moments were applied in the plane of the major axis of the ellipse.

Bending characteristics of resin concretes

Directory of Open Access Journals (Sweden)

Ribeiro Maria Cristina Santos

2003-01-01

Full Text Available In this research work the influence of composition and curing conditions in bending strength of polyester and epoxy concrete is analyzed. Various mixtures of resin and aggregates were considered in view of an optimal combination. The Taguchi methodology was applied in order to reduce the number of tests, and in order to evaluate the influence of various parameters in concrete properties. This methodology is very useful for the planning of experiments. Test results, analyzed by this methodology, shown that the most significant factors affecting bending strength properties of resin concretes are the type of resin, resin content and charge content. An optimal formulation leading to a maximum bending strength was achieved in terms of material parameters.

The big data phenomenon: The business and public impact

Directory of Open Access Journals (Sweden)

Chroneos-Krasavac Biljana

2016-01-01

Full Text Available The subject of the research in this paper is the emergence of big data phenomenon and application of big data technologies for business' needs with the specific emphasis on marketing and trade. The purpose of the research is to make a comprehensive overview of different discussions about the characteristics, application possibilities, achievements, constraints and the future of big data development. Based on the relevant literature, the concept of big data is presented and the potential of large impact of big data on business activities is discussed. One of the key findings indicates that the most prominent change that big data brings to the business arena is the appearance of new business models, as well as revisions of the existing ones. Substantial part of the paper is devoted to the marketing and marketing research which are under the strong impact of big data. The most exciting outcomes of the research in this domain concerns the new abilities in profiling the customers. In addition to the vast amount of structured data which are used in marketing for a long period, big data initiatives suggest the inclusion of semi-structured and unstructured data, opening up the room for substantial improvements in customer profile analysis. Considering the usage of information communication technologies (ICT as a prerequisite for big data project success, the concept of Networked Readiness Index (NRI is presented and the position of Serbia and regional countries in NRI framework is analyzed. The main outcome of the analysis points out that Serbia, with its NRI score took the lowest position in the region, excluding Albania. Also, Serbia is lagging behind the appropriate EU mean values regarding all observed composite indicators - pillars. Further on, this analysis reveals the domains of ICT usage in Serbia, which could be focused for an improvement and where incentives can be made. These domains are: political and regulatory environment, business and

Crustal strain near the Big Bend of the San Andreas Fault: Analysis of the Los Padres-Tehachapi Trilateration Networks, California

Science.gov (United States)

Eberhart-Phillips, Donna; Lisowski, Michael; Zoback, Mark D.

1990-02-01

In the region of the Los Padres-Tehachapi geodetic network, the San Andreas fault (SAF) changes its orientation by over 30° from N40°W, close to that predicted by plate motion for a transform boundary, to N73°W. The strain orientation near the SAF is consistent with right-lateral shear along the fault, with maximum shear rate of 0.38±0.01 μrad/yr at N63°W. In contrast, away from the SAF the strain orientations on both sides of the fault are consistent with the plate motion direction, with maximum shear rate of 0.19±0.01 μrad/yr at N44°W. The strain rate does not drop off rapidly away from the fault, and thus the area is fit by either a broad shear zone below the SAF or a single fault with a relatively deep locking depth. The fit to the line length data is poor for locking depth d less than 25 km. For d of 25 km a buried slip rate of 30 ± 6 mm/yr is estimated. We also estimated buried slip for models that included the Garlock and Big Pine faults, in addition to the SAF. Slip rates on other faults are poorly constrained by the Los Padres-Tehachapi network. The best fitting Garlock fault model had computed left-lateral slip rate of 11±2 mm/yr below 10 km. Buried left-lateral slip of 15±6 mm/yr on the Big Pine fault, within the Western Transverse Ranges, provides significant reduction in line length residuals; however, deformation there may be more complicated than a single vertical fault. A subhorizontal detachment on the southern side of the SAF cannot be well constrained by these data. We investigated the location of the SAF and found that a vertical fault below the surface trace fits the data much better than either a dipping fault or a fault zone located south of the surface trace.

Bending-Tolerant Anodes for Lithium-Metal Batteries.

Science.gov (United States)

Wang, Aoxuan; Tang, Shan; Kong, Debin; Liu, Shan; Chiou, Kevin; Zhi, Linjie; Huang, Jiaxing; Xia, Yong-Yao; Luo, Jiayan

2018-01-01

Bendable energy-storage systems with high energy density are demanded for conformal electronics. Lithium-metal batteries including lithium-sulfur and lithium-oxygen cells have much higher theoretical energy density than lithium-ion batteries. Reckoned as the ideal anode, however, Li has many challenges when directly used, especially its tendency to form dendrite. Under bending conditions, the Li-dendrite growth can be further aggravated due to bending-induced local plastic deformation and Li-filaments pulverization. Here, the Li-metal anodes are made bending tolerant by integrating Li into bendable scaffolds such as reduced graphene oxide (r-GO) films. In the composites, the bending stress is largely dissipated by the scaffolds. The scaffolds have increased available surface for homogeneous Li plating and minimize volume fluctuation of Li electrodes during cycling. Significantly improved cycling performance under bending conditions is achieved. With the bending-tolerant r-GO/Li-metal anode, bendable lithium-sulfur and lithium-oxygen batteries with long cycling stability are realized. A bendable integrated solar cell-battery system charged by light with stable output and a series connected bendable battery pack with higher voltage is also demonstrated. It is anticipated that this bending-tolerant anode can be combined with further electrolytes and cathodes to develop new bendable energy systems. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Flow patterns and hydraulic losses in quasi-coil pipes : The effects of configuration of bend cross section, curvature ratio and bend angle

OpenAIRE

Shimizu, Yukimaru; Sugino, Koichi; Yasui, Masaji; Hayakawa, Yukitaka; Kuzuhara, Sadao

1985-01-01

Pipes with bend combinations are much used in the heat exchangers, since the curved path in the bends promotes the mixing in flow for active heat transfer. In the present paper, one of the pipes with bend combinations, namely, quasi-coiled pipes composed of many bend elements are investigated, and the relationships between the hydraulic loss and the secondary flow are studied experimentally. The configurations of the cross sections, the bent angles and the curvature ratios of the bend element...

BigOP: Generating Comprehensive Big Data Workloads as a Benchmarking Framework

OpenAIRE

Zhu, Yuqing; Zhan, Jianfeng; Weng, Chuliang; Nambiar, Raghunath; Zhang, Jinchao; Chen, Xingzhen; Wang, Lei

2014-01-01

Big Data is considered proprietary asset of companies, organizations, and even nations. Turning big data into real treasure requires the support of big data systems. A variety of commercial and open source products have been unleashed for big data storage and processing. While big data users are facing the choice of which system best suits their needs, big data system developers are facing the question of how to evaluate their systems with regard to general big data processing needs. System b...

Symmetric bends how to join two lengths of cord

CERN Document Server

Miles, Roger E

1995-01-01

A bend is a knot securely joining together two lengths of cord (or string or rope), thereby yielding a single longer length. There are many possible different bends, and a natural question that has probably occurred to many is: "Is there a 'best' bend and, if so, what is it?"Most of the well-known bends happen to be symmetric - that is, the two constituent cords within the bend have the same geometric shape and size, and interrelationship with the other. Such 'symmetric bends' have great beauty, especially when the two cords bear different colours. Moreover, they have the practical advantage o

Tunable waveguide bends with graphene-based anisotropic metamaterials

KAUST Repository

Chen, Zhao-xian; Chen, Ze-guo; Ming, Yang; Wu, Ying; Lu, Yan-qing

2016-01-01

We design tunable waveguide bends filled with graphene-based anisotropic metamaterials to achieve a nearly perfect bending effect. The anisotropic properties of the metamaterials can be described by the effective medium theory. The nearly perfect bending effect is demonstrated by finite element simulations of various structures with different bending curvatures and shapes. This effect is attributed to zero effective permittivity along the direction of propagation and matched effective impedance at the interfaces between the bending part and the dielectric waveguides. We envisage that the design will be applicable in the far-infrared and terahertz frequency ranges owing to the tunable dielectric responses of graphene.

Tunable waveguide bends with graphene-based anisotropic metamaterials

KAUST Repository

Chen, Zhao-xian

2016-01-15

We design tunable waveguide bends filled with graphene-based anisotropic metamaterials to achieve a nearly perfect bending effect. The anisotropic properties of the metamaterials can be described by the effective medium theory. The nearly perfect bending effect is demonstrated by finite element simulations of various structures with different bending curvatures and shapes. This effect is attributed to zero effective permittivity along the direction of propagation and matched effective impedance at the interfaces between the bending part and the dielectric waveguides. We envisage that the design will be applicable in the far-infrared and terahertz frequency ranges owing to the tunable dielectric responses of graphene.

Bending stresses in Facetted Glass Shells

DEFF Research Database (Denmark)

Bagger, Anne; Jönsson, Jeppe; Almegaard, Henrik

2008-01-01

A shell structure of glass combines a highly effective structural principle with a material of optimal permeability to light. A facetted shell structure has a piecewise plane geometry, and together the facets form an approximation to a curved surface. A distributed load on a plane-based facetted...... structure will locally cause bending moments in the loaded facets. The bending stresses are dependent on the stiffness of the joints. Approximate solutions are developed to estimate the magnitude of the bending stresses. A FE-model of a facetted glass shell structure is used to validate the expressions...

Paleomagnetic modeling of seamounts near the Hawaiian Emperor bend

Science.gov (United States)

Sager, William W.; Lamarche, Amy J.; Kopp, Christian

2005-08-01

The Hawaiian-Emperor Seamount chain records the motion of the Pacific Plate relative to the Hawaiian mantle hotspot for ˜80 m.y. A notable feature of the chain is the pronounced bend at its middle. This bend had been widely credited to a change in plate motion, but recent research suggests a change in hotspot motion as an alternative. Existing paleomagnetic data from the Emperor Chain suggest that the hotspot moved south during the Late Cretaceous and Early Tertiary, but reached its current latitude by the age of the bend. Thus, data from area of the bend are important for understanding changes in plume latitude. In this study, we analyze the magnetic anomalies of five seamounts (Annei, Daikakuji-W, Daikakuji- E, Abbott, and Colahan) in the region of the bend. These particular seamounts were chosen because they have been recently surveyed to collect multibeam bathymetry and magnetic data positioned with GPS navigation. Inversions of the magnetic and bathymetric data were performed to determine the mean magnetization of each seamount and from these results, paleomagnetic poles and paleolatitudes were calculated. Three of the five seamounts have reversed magnetic polarities (two are normal) and four contain a small volume of magnetic polarity opposite to the main body, consistent with formation during the Early Cenozoic, a time of geomagnetic field reversals. Although magnetization inhomogene ties can degrade the accuracy of paleomagnetic poles calculated from such models, the seamounts give results consistent with one another and with other Pacific paleomagnetic data of approximately the same age. Seamount paleolatitudes range from 13.7 to 23.7, with an average of 19.4 ± 7.4 (2σ). These values are indistinguishable from the present-day paleolatitude of the Hawaiian hotspot. Together with other paleomagnetic and geologic evidence, these data imply that the Hawaiian hotspot has moved little in latitude during the past ˜45 m.y.

How Big Is Too Big?

Science.gov (United States)

Cibes, Margaret; Greenwood, James

2016-01-01

Media Clips appears in every issue of Mathematics Teacher, offering readers contemporary, authentic applications of quantitative reasoning based on print or electronic media. This issue features "How Big is Too Big?" (Margaret Cibes and James Greenwood) in which students are asked to analyze the data and tables provided and answer a…

Effects of laser bending on the microstructural constituents

CSIR Research Space (South Africa)

Tshabalala, L

2012-01-01

Full Text Available This article will illustrate the correlation between microstructural and microhardness changes in high-strength-low-alloy steel that occur as a result of laser-bending. Laser bending is a process of bending metal shapes using the laser beam...

Three-dimensional flow structure and patterns of bed shear stress in an evolving compound meander bend

Science.gov (United States)

Engel, Frank; Rhoads, Bruce L.

2016-01-01

Compound meander bends with multiple lobes of maximum curvature are common in actively evolving lowland rivers. Interaction among spatial patterns of mean flow, turbulence, bed morphology, bank failures and channel migration in compound bends is poorly understood. In this paper, acoustic Doppler current profiler (ADCP) measurements of the three-dimensional (3D) flow velocities in a compound bend are examined to evaluate the influence of channel curvature and hydrologic variability on the structure of flow within the bend. Flow structure at various flow stages is related to changes in bed morphology over the study timeframe. Increases in local curvature within the upstream lobe of the bend reduce outer bank velocities at morphologically significant flows, creating a region that protects the bank from high momentum flow and high bed shear stresses. The dimensionless radius of curvature in the upstream lobe is one-third less than that of the downstream lobe, with average bank erosion rates less than half of the erosion rates for the downstream lobe. Higher bank erosion rates within the downstream lobe correspond to the shift in a core of high velocity and bed shear stresses toward the outer bank as flow moves through the two lobes. These erosion patterns provide a mechanism for continued migration of the downstream lobe in the near future. Bed material size distributions within the bend correspond to spatial patterns of bed shear stress magnitudes, indicating that bed material sorting within the bend is governed by bed shear stress. Results suggest that patterns of flow, sediment entrainment, and planform evolution in compound meander bends are more complex than in simple meander bends. Moreover, interactions among local influences on the flow, such as woody debris, local topographic steering, and locally high curvature, tend to cause compound bends to evolve toward increasing planform complexity over time rather than stable configurations.

Electrostatic bending response of a charged helix

Science.gov (United States)

Zampetaki, A. V.; Stockhofe, J.; Schmelcher, P.

2018-04-01

We explore the electrostatic bending response of a chain of charged particles confined on a finite helical filament. We analyze how the energy difference Δ E between the bent and the unbent helical chain scales with the length of the helical segment and the radius of curvature and identify features that are not captured by the standard notion of the bending rigidity, normally used as a measure of bending tendency in the linear response regime. Using Δ E to characterize the bending response of the helical chain we identify two regimes with qualitatively different bending behaviors for the ground state configuration: the regime of small and the regime of large radius-to-pitch ratio, respectively. Within the former regime, Δ E changes smoothly with the variation of the system parameters. Of particular interest are its oscillations with the number of charged particles encountered for commensurate fillings which yield length-dependent oscillations in the preferred bending direction of the helical chain. We show that the origin of these oscillations is the nonuniformity of the charge distribution caused by the long-range character of the Coulomb interactions and the finite length of the helix. In the second regime of large values of the radius-to-pitch ratio, sudden changes in the ground state structure of the charges occur as the system parameters vary, leading to complex and discontinuous variations in the ground state bending response Δ E .

Effects of tanalith-e impregnation substance on bending strengths and modulus of elasticity in bending of some wood types

Directory of Open Access Journals (Sweden)

Hakan Keskin

2016-04-01

Full Text Available The aim of this study was to investigate the effects of impregnation with Tanalith-E on the bending strengths and modulus of elasticity in bending of some wood types. The test samples prepared from beech, oak, walnut, poplar, ash and pine wood materials - that are of common use in the forest products industry of TURKEY - according to TS 345, were treated with according to ASTM D 1413-76 substantially. Un-impregnated samples according to impregnated wood materials, the bending strengths in beech to 6.83%, 5.12% in ash, 5.93% in pine, the elasticity module values to 7.15% in oak and ash, at a rate of 6.58% in the higher were found. The highest values of bending strengths and modulus of elasticity in bending were obtained in beech and ash woods impregnated with Tanalith-E, whereas the lowest values were obtained in the poplar wood.

A numerical study on the flow development around a rotating square-sectioned U-Bend( II )

International Nuclear Information System (INIS)

Lee, Gong Hee; Baek, Je Hyun

2002-01-01

The present study investigates in detail the combined effects of the Coriolis force and centrifugal force on the development of turbulent flows in a square-sectioned U-bend rotating about an axis parallel to the center of bend curvature. When a viscous fluid flows through a curved region of U-bend, two types of secondary flow occur. One is caused by the Coriolis force due to the rotation of U-bend and the other by the centrifugal force due to the curvature of U-bend. For positive rotation, where the rotation is in the same direction as that of the main flow, both the Coriolis force and the centrifugal force act radially outwards. Therefore, the flow structure is qualitatively similar to that observed in a stationary curved duct. On the other hand, under negative rotation, where these two forces act in opposite direction, more complex flow fields can be observed depending on the relative magnitudes of the forces. Under the condition that the value of Rossby number and curvature ratio is large, the flow field in a rotating U-bend can be represented by two dimensionless parameters : K LC = Re 1/4 / √ λ and a body force ratio F= λ/Ro. Here, K TC has the same dynamical meaning as K LC = Re/√ λ for laminar flow

Big Bang Darkleosynthesis

OpenAIRE

Krnjaic, Gordan; Sigurdson, Kris

2014-01-01

In a popular class of models, dark matter comprises an asymmetric population of composite particles with short range interactions arising from a confined nonabelian gauge group. We show that coupling this sector to a well-motivated light mediator particle yields efficient darkleosynthesis , a dark-sector version of big-bang nucleosynthesis (BBN), in generic regions of parameter space. Dark matter self-interaction bounds typically require the confinement scale to be above ΛQCD , which generica...

Standard test methods for bend testing of material for ductility

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 These test methods cover bend testing for ductility of materials. Included in the procedures are four conditions of constraint on the bent portion of the specimen; a guided-bend test using a mandrel or plunger of defined dimensions to force the mid-length of the specimen between two supports separated by a defined space; a semi-guided bend test in which the specimen is bent, while in contact with a mandrel, through a specified angle or to a specified inside radius (r) of curvature, measured while under the bending force; a free-bend test in which the ends of the specimen are brought toward each other, but in which no transverse force is applied to the bend itself and there is no contact of the concave inside surface of the bend with other material; a bend and flatten test, in which a transverse force is applied to the bend such that the legs make contact with each other over the length of the specimen. 1.2 After bending, the convex surface of the bend is examined for evidence of a crack or surface irregu...

Metal-bending brake facilitates lightweight, close-tolerance fabrication

Science.gov (United States)

Ercoline, A. L.; Wilton, K. B.

1964-01-01

A lightweight, metal bending brake ensures very accurate bends. Features of the brake that adapt it for making complex reverse bends to close tolerances are a pronounced relief or cutaway of the underside of the bodyplate combined with modification in the leaf design and its suspension.

Nursing Needs Big Data and Big Data Needs Nursing.

Science.gov (United States)

Brennan, Patricia Flatley; Bakken, Suzanne

2015-09-01

Contemporary big data initiatives in health care will benefit from greater integration with nursing science and nursing practice; in turn, nursing science and nursing practice has much to gain from the data science initiatives. Big data arises secondary to scholarly inquiry (e.g., -omics) and everyday observations like cardiac flow sensors or Twitter feeds. Data science methods that are emerging ensure that these data be leveraged to improve patient care. Big data encompasses data that exceed human comprehension, that exist at a volume unmanageable by standard computer systems, that arrive at a velocity not under the control of the investigator and possess a level of imprecision not found in traditional inquiry. Data science methods are emerging to manage and gain insights from big data. The primary methods included investigation of emerging federal big data initiatives, and exploration of exemplars from nursing informatics research to benchmark where nursing is already poised to participate in the big data revolution. We provide observations and reflections on experiences in the emerging big data initiatives. Existing approaches to large data set analysis provide a necessary but not sufficient foundation for nursing to participate in the big data revolution. Nursing's Social Policy Statement guides a principled, ethical perspective on big data and data science. There are implications for basic and advanced practice clinical nurses in practice, for the nurse scientist who collaborates with data scientists, and for the nurse data scientist. Big data and data science has the potential to provide greater richness in understanding patient phenomena and in tailoring interventional strategies that are personalized to the patient. © 2015 Sigma Theta Tau International.

Load tests with a pipe bend DN 425, applying slowly changing bending loads up to occurrence of leak

International Nuclear Information System (INIS)

Uhlmann, D.; Hunger, H.

1990-01-01

The experimental program deals with the formation of incipient cracks and subsequent crack growth of axially oriented cracks at a pipe bend with a nominal width of DN 425. The pipe bend consists of the ferritic material 20MnMoNi55. The numerical experiments by means of 3 D-FE analyses concentrate on determining the influence of the asymmetric crack depths at the two bend halves, and of the multiple crack fields, on the effective crack strain. (DG) [de

BIG Data - BIG Gains? Understanding the Link Between Big Data Analytics and Innovation

OpenAIRE

Niebel, Thomas; Rasel, Fabienne; Viete, Steffen

2017-01-01

This paper analyzes the relationship between firms’ use of big data analytics and their innovative performance for product innovations. Since big data technologies provide new data information practices, they create new decision-making possibilities, which firms can use to realize innovations. Applying German firm-level data we find suggestive evidence that big data analytics matters for the likelihood of becoming a product innovator as well as the market success of the firms’ product innovat...

Networking for big data

CERN Document Server

Yu, Shui; Misic, Jelena; Shen, Xuemin (Sherman)

2015-01-01

Networking for Big Data supplies an unprecedented look at cutting-edge research on the networking and communication aspects of Big Data. Starting with a comprehensive introduction to Big Data and its networking issues, it offers deep technical coverage of both theory and applications.The book is divided into four sections: introduction to Big Data, networking theory and design for Big Data, networking security for Big Data, and platforms and systems for Big Data applications. Focusing on key networking issues in Big Data, the book explains network design and implementation for Big Data. It exa

Mechanical behaviour of bending bucky-gel actuators and its representation

International Nuclear Information System (INIS)

Kruusamäe, Karl; Mukai, Ken; Sugino, Takushi; Asaka, Kinji

2014-01-01

Bucky-gel actuators are ionic electromechanically active materials that bend in response to a low-voltage excitation. While bending actuators may offer new approaches in engineering solutions, the characterization of bending poses many challenges in comparison to conventional rotary motion. It is often desired to reduce the bending behaviour to a single parameter, which may lead to the loss of accuracy in modelling. A high-speed laser profilometer is utilized to characterize the bending response of different bucky-gel actuators at their full length and to critically compare the applicability of existing representation tools for bending. The best analytical representation of the bending of a bucky-gel actuator is found to be in the form of a power function. It is also observed that, along the length of the actuator, sections closer to the electrical input clamp exhibit back-relaxation (a common drawback for bending ionic actuators) already when the far end of the bending strip is still in forward motion. (paper)

Big Argumentation?

Directory of Open Access Journals (Sweden)

Daniel Faltesek

2013-08-01

Full Text Available Big Data is nothing new. Public concern regarding the mass diffusion of data has appeared repeatedly with computing innovations, in the formation before Big Data it was most recently referred to as the information explosion. In this essay, I argue that the appeal of Big Data is not a function of computational power, but of a synergistic relationship between aesthetic order and a politics evacuated of a meaningful public deliberation. Understanding, and challenging, Big Data requires an attention to the aesthetics of data visualization and the ways in which those aesthetics would seem to depoliticize information. The conclusion proposes an alternative argumentative aesthetic as the appropriate response to the depoliticization posed by the popular imaginary of Big Data.

The Sierra de Cabral range: a restraining bend related to the Sierra Ballena shear zone in Dom Feliciano belt

International Nuclear Information System (INIS)

Masquelin, H.

2010-01-01

Restraining and releasing bends occurring in all crustal environments are common but enigmatic features of strike-slip fault systems. They can be reported in all scales of observation. Regional-scale restraining bends are sites of mountain building, transpressional deformation and basement exhumation. Releasing bends are sites of subsidence, transtensional deformation and pull-apart basins. The Dom Feliciano Belt of Southern Uruguay has two main structures observed from the outer space: (i) the Sierra Ballena Shear Zone and (ii) the Sierra de Cabral flexure located to the SW of the former. Although a transpressional regime is commonly accepted for the Dom Feliciano Belt, the available tectonic models do not provide satisfactory explanations for its building mechanism. A restraining bend is proposed at the SW termination of Sierra Ballena strike-slip ductile shear zone. In a key-area (Alvariza Range) the relationship between the Zanja del Tigre volcanic-detritic and the calcareous succession shows three en-échelon upright bends of the same quartzite hanging-wall between two sub-vertical strike-slip faults, suggesting the existence of a shortened strike-slip duplex operating in viscous-elastic rheology. The deformation partitioning includes strike-slip and dip-slip simple-shear components as well as one contractional pure-shear component. Because restraining bends were scarcely described in Neoproterozoic low-grade regional exhumation conditions, this structural framework would be a natural laboratory to study fault kinematics, fault dynamics, their associated deformation and the tectonic and erosion constraints related to the exhumation of many crystalline terrains

Big Data: Evaluating business value and firm performance

OpenAIRE

Vitari , Claudio; Raguseo , Elisabetta

2016-01-01

This report is an output of a research project co-financed by Grenoble Ecole de Management and Auvergne-Rhône-Alpes French region. This study was conducted with the aim of understanding how Information Technology (IT) provides new opportunities to firms, specifically focusing on the role of Big Data in creating value for the companies. Gartner defines Big Data as “high volume, velocity and/or variety information assets that demand cost-effective, innovative forms of information processing tha...

A bend thickness sensitivity study of Candu feeder piping

International Nuclear Information System (INIS)

Li, M.; Aggarwal, M.L.; Meysner, A.; Micelotta, C.

2005-01-01

In CANDU reactors, feeder bends close to the connection at the fuel channel may be subjected to the highest Flow Accelerated Corrosion (FAC) and stresses. Feeder pipe stress analysis is crucial in the life extension of aging CANDU plants. Typical feeder pipes are interconnected by upper link plates and spacers. It is well known that the stresses at the bends are sensitive to the local bend thicknesses. It is also known from the authors' study (Li and et al, 2005) that feeder inter linkage effect is significant and cannot be ignored. The field measurement of feeder bend thickness is difficult and may be subjected to uncertainty in accuracy. Hence, it is desirable to know how the stress on a subject feeder could be affected by the bend thickness variation of the neighboring feeders. This effect cannot be evaluated by the traditional 'single' feeder model approach. In this paper, the 'row' and 'combined' models developed in the previous study (Li and et al, 2005), which include the feeder interactions, are used to investigate the sensitivity of bend thickness. A series of random thickness bounded by maximum and minimum measured values were applied to feeders in the model. The results show that an individual feeder is not sensitive to the bend thickness variation of the remaining feeders in the model, but depends primarily on its own bend thickness. The highest stress at a feeder always occurs when the feeder has the smallest possible bend thickness. A minimum acceptable bend thickness for individual feeders can be computed by an iterative computing process. The dependency of field thickness measurement and the amount of required analysis work can be greatly reduced. (authors)

Bend Faulting at the Edge of a Flat Slab: The 2017 Mw7.1 Puebla-Morelos, Mexico Earthquake

Science.gov (United States)

Melgar, Diego; Pérez-Campos, Xyoli; Ramirez-Guzman, Leonardo; Spica, Zack; Espíndola, Victor Hugo; Hammond, William C.; Cabral-Cano, Enrique

2018-03-01

We present results of a slip model from joint inversion of strong motion and static Global Positioning System data for the Mw7.1 Puebla-Morelos earthquake. We find that the earthquake nucleates at the bottom of the oceanic crust or within the oceanic mantle with most of the moment release occurring within the oceanic mantle. Given its location at the edge of the flat slab, the earthquake is likely the result of bending stresses occurring at the transition from flat slab subduction to steeply dipping subduction. The event strikes obliquely to the slab, we find a good agreement between the seafloor fabric offshore the source region and the strike of the earthquake. We argue that the event likely reactivated a fault first created during seafloor formation. We hypothesize that large bending-related events at the edge of the flat slab are more likely in areas of low misalignment between the seafloor fabric and the slab strike where reactivation of preexisting structures is favored. This hypothesis predicts decreased likelihood of bending-related events northwest of the 2017 source region but also suggests that they should be more likely southeast of the 2017 source region.

Big data

DEFF Research Database (Denmark)

Madsen, Anders Koed; Flyverbom, Mikkel; Hilbert, Martin

2016-01-01

is to outline a research agenda that can be used to raise a broader set of sociological and practice-oriented questions about the increasing datafication of international relations and politics. First, it proposes a way of conceptualizing big data that is broad enough to open fruitful investigations......The claim that big data can revolutionize strategy and governance in the context of international relations is increasingly hard to ignore. Scholars of international political sociology have mainly discussed this development through the themes of security and surveillance. The aim of this paper...... into the emerging use of big data in these contexts. This conceptualization includes the identification of three moments contained in any big data practice. Second, it suggests a research agenda built around a set of subthemes that each deserve dedicated scrutiny when studying the interplay between big data...

Temperature-Insensitive Bend Sensor Using Entirely Centered Erbium Doping in the Fiber Core

Directory of Open Access Journals (Sweden)

Sulaiman Wadi Harun

2013-07-01

Full Text Available A fiber based bend sensor using a uniquely designed Bend-Sensitive Erbium Doped Fiber (BSEDF is proposed and demonstrated. The BSEDF has two core regions, namely an undoped outer region with a diameter of about 9.38 μm encompassing a doped, inner core region with a diameter of 4.00 μm. The doped core region has about 400 ppm of an Er2O3 dopant. Pumping the BSEDF with a conventional 980 nm laser diode gives an Amplified Spontaneous Emission (ASE spectrum spanning from 1,510 nm to over 1,560 nm at the output power level of about −58 dBm. The ASE spectrum has a peak power of −52 dBm at a central wavelength of 1,533 nm when not spooled. Spooling the BSEDF with diameters of 10 cm to 2 cm yields decreasing peak powers from −57.0 dBm to −61.8 dBm, while the central wavelength remains unchanged. The output is highly stable over time, with a low temperature sensitivity of around ~0.005 dBm/°C, thus allowing for the development of a highly stable sensor system based in the change of the peak power alone.

Effect of Ovality in Inlet Pigtail Pipe Bends Under Combined Internal Pressure and In-Plane Bending for Ni-Fe-Cr B407 Material

Directory of Open Access Journals (Sweden)

Ramaswami P.

2017-09-01

Full Text Available The present paper makes an attempt to depict the effect of ovality in the inlet pigtail pipe bend of a reformer under combined internal pressure and in-plane bending. Finite element analysis (FEA and experiments have been used. An incoloy Ni-Fe-Cr B407 alloy material was considered for study and assumed to be elastic-perfectly plastic in behavior. The design of pipe bend is based on ASME B31.3 standard and during manufacturing process, it is challenging to avoid thickening on the inner radius and thinning on the outer radius of pipe bend. This geometrical shape imperfection is known as ovality and its effect needs investigation which is considered for the study. The finite element analysis (ANSYS-workbench results showed that ovality affects the load carrying capacity of the pipe bend and it was varying with bend factor (h. By data fitting of finite element results, an empirical formula for the limit load of inlet pigtail pipe bend with ovality has been proposed, which is validated by experiments.

Ankle-foot orthosis bending axis influences running mechanics.

Science.gov (United States)

Russell Esposito, Elizabeth; Ranz, Ellyn C; Schmidtbauer, Kelly A; Neptune, Richard R; Wilken, Jason M

2017-07-01

Passive-dynamic ankle-foot orthoses (AFOs) are commonly prescribed to improve locomotion for people with lower limb musculoskeletal weakness. The clinical prescription and design process are typically qualitative and based on observational assessment and experience. Prior work examining the effect of AFO design characteristics generally excludes higher impact activities such as running, providing clinicians and researchers limited information to guide the development of objective prescription guidelines. The proximal location of the bending axis may directly influence energy storage and return and resulting running mechanics. The purpose of this study was to determine if the location of an AFO's bending axis influences running mechanics. Marker and force data were recorded as 12 participants with lower extremity weakness ran overground while wearing a passive-dynamic AFO with posterior struts manufactured with central (middle) and off-centered (high and low) bending axes. Lower extremity joint angles, moments, powers, and ground reaction forces were calculated and compared between limbs and across bending axis conditions. Bending axis produced relatively small but significant changes. Ankle range of motion increased as the bending axis shifted distally (pbenefits during running, although individual preference and physical ability should also be considered. Published by Elsevier B.V.

Bending and tensile deformation of metallic nanowires

International Nuclear Information System (INIS)

McDowell, Matthew T; Leach, Austin M; Gall, Ken

2008-01-01

Using molecular statics simulations and the embedded atom method, a technique for bending silver nanowires and calculating Young's modulus via continuum mechanics has been developed. The measured Young's modulus values extracted from bending simulations were compared with modulus values calculated from uniaxial tension simulations for a range of nanowire sizes, orientations and geometries. Depending on axial orientation, the nanowires exhibit stiffening or softening under tension and bending as size decreases. Bending simulations typically result in a greater variation of Young's modulus values with nanowire size compared with tensile deformation, which indicates a loading-method-dependent size effect on elastic properties at sub-5 nm wire diameters. Since the axial stress is maximized at the lateral surfaces in bending, the loading-method-dependent size effect is postulated to be primarily a result of differences in nanowire surface and core elastic modulus. The divergence of Young's modulus from the bulk modulus in these simulations occurs at sizes below the range in which experiments have demonstrated a size scale effect on elastic properties of metallic nanowires. This difference indicates that other factors beyond native metallic surface properties play a role in experimentally observed nanowire elastic modulus size effects

Big data computing

CERN Document Server

Akerkar, Rajendra

2013-01-01

Due to market forces and technological evolution, Big Data computing is developing at an increasing rate. A wide variety of novel approaches and tools have emerged to tackle the challenges of Big Data, creating both more opportunities and more challenges for students and professionals in the field of data computation and analysis. Presenting a mix of industry cases and theory, Big Data Computing discusses the technical and practical issues related to Big Data in intelligent information management. Emphasizing the adoption and diffusion of Big Data tools and technologies in industry, the book i

Passport to the Big Bang moves across the road

CERN Document Server

Corinne Pralavorio

2015-01-01

The ATLAS platform of the Passport to the Big Bang circuit has been relocated in front of the CERN Reception.   The ATLAS platform of the Passport to the Big Bang, outside the CERN Reception building. The Passport to the Big Bang platform of the ATLAS Experiment has been moved in front of the CERN Reception to make it more visible and accessible. It had to be dismantled and moved from its previous location in the garden of the Globe of Science and Innovation due to the major refurbishment work in progress on the Globe, and is now fully operational in its new location on the other side of the road, in the Main Reception car-park. The Passport to the Big Bang circuit, inaugurated in 2013, comprises ten platforms installed in front of ten CERN sites and aims to help local residents and visitors to the region understand CERN's research. Dedicated Passport to the Big Bang flyers, containing all necessary information and riddles for you to solve, are available at the CERN Rec...

Smoothed particle hydrodynamics simulations of flow separation at bends

NARCIS (Netherlands)

Hou, Q.; Kruisbrink, A.C.H.; Pearce, F.R.; Tijsseling, A.S.; Yue, T.

2014-01-01

The separated flow in two-dimensional bends is numerically simulated for a right-angled bend with different ratios of the channel widths and for a symmetric bend with different turning angles. Unlike the potential flow solutions that have several restrictive assumptions, the Euler equations are

Smoothed particle hydrodynamics simulations of flow separation at bends

NARCIS (Netherlands)

Hou, Q.; Kruisbrink, A.C.H.; Pearce, F.R.; Tijsseling, A.S.; Yue, T.

2013-01-01

The separated flow in two-dimensional bends is numerically simulated for a right-angled bend with different ratios of the channel widths and for a symmetric bend with different turning angles. Unlike the potential flow solutions that have several restrictive assumptions, the Euler equations are

BIG data - BIG gains? Empirical evidence on the link between big data analytics and innovation

OpenAIRE

Niebel, Thomas; Rasel, Fabienne; Viete, Steffen

2017-01-01

This paper analyzes the relationship between firms’ use of big data analytics and their innovative performance in terms of product innovations. Since big data technologies provide new data information practices, they create novel decision-making possibilities, which are widely believed to support firms’ innovation process. Applying German firm-level data within a knowledge production function framework we find suggestive evidence that big data analytics is a relevant determinant for the likel...

The influence of end constraints on smooth pipe bends

International Nuclear Information System (INIS)

Thomson, G.; Spence, J.

1981-01-01

With present trends in the power industries towards higher operating temperatures and pressures, problems associated with the design and safety assessment of pipework systems have become increasingly complex. Within such systems, the importance of smooth pipe bends is well established. The work which will be presented will attempt to clarify the situation and unify the results. An analytical solution of the problem of a linear elastic smooth pipe bend with end constraints under in-plane bending will be presented. The analysis will deal with constraints in the form of flanged tangents of any length. The analysis employs the theorem of minimum total potential energy with suitable kinematically admissible displacements in the form of Fourier series. The integrations and minimisation were performed numerically, thereby permitting the removal of several of the assumptions made by previous authors. Typical results for flexibilities will be given along with comparisons with other works. The differences in some earlier theory are clarified and other more recent work using different solution techniques is substantiated. The bend behaviour is shown to be strongly influenced by the pipe bend parameter, the bend angle, the tangent pipe length and the bend/cross-sectional radius ratio. (orig./GL)

Induction bending of API 5L X80 pipes; Curvamento a quente de tubos API 5L X80

Energy Technology Data Exchange (ETDEWEB)

Batista, Gilmar Z. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)]. E-mail: g.zacca@petrobras.com.br; Naschpitz, Leonardo [Primus Processamento de Tubos S.A. - PROTUBO, Campo Grande, RJ (Brazil)]. E-mail: naschpitz@protubo.com.br

2005-07-01

The present work is a part of an extensive program to make possible the application of API 5L X80 in pipeline construction in Brazil. At this stage, the effect of the induction bending process on the microstructure and mechanical properties of the pipe is presented. For this study an API 5L X80 pipe, made by the UOE process, is used. The pipe was manufactured from a plate produced by thermo-mechanically controlled rolling without accelerated cooling. The pipe bending was carried out applying a local induction heating following by water quenching. The bend section, outer and inner curvature regions, of the pipe bend were evaluated and compared with the original pipe. The longitudinal weld and transition zones were not evaluated at this stage. Dimensional analyses, microstructural evaluation, Charpy-V impact tests, and tensile tests were performed. A significant microstructural change was verified in the bend area. The yield strength of the pipe bend was found to be lower than original pipe and standard requirements. Other tensile properties and impact properties are compatible with API 5L X80 requirements. (author)

Bends and splitters in graphene nanoribbon waveguides

DEFF Research Database (Denmark)

Zhu, Xiaolong; Yan, Wei; Mortensen, N. Asger

2013-01-01

We investigate the performance of bends and splitters in graphene nanoribbon waveguides. Although the graphene waveguides are lossy themselves, we show that bends and splitters do not induce any additional loss provided that the nanoribbon width is sub-wavelength. We use transmission line theory...

'Big data' in mental health research: current status and emerging possibilities.

Science.gov (United States)

Stewart, Robert; Davis, Katrina

2016-08-01

'Big data' are accumulating in a multitude of domains and offer novel opportunities for research. The role of these resources in mental health investigations remains relatively unexplored, although a number of datasets are in use and supporting a range of projects. We sought to review big data resources and their use in mental health research to characterise applications to date and consider directions for innovation in future. A narrative review. Clear disparities were evident in geographic regions covered and in the disorders and interventions receiving most attention. We discuss the strengths and weaknesses of the use of different types of data and the challenges of big data in general. Current research output from big data is still predominantly determined by the information and resources available and there is a need to reverse the situation so that big data platforms are more driven by the needs of clinical services and service users.

Benchmarking Big Data Systems and the BigData Top100 List.

Science.gov (United States)

Baru, Chaitanya; Bhandarkar, Milind; Nambiar, Raghunath; Poess, Meikel; Rabl, Tilmann

2013-03-01

"Big data" has become a major force of innovation across enterprises of all sizes. New platforms with increasingly more features for managing big datasets are being announced almost on a weekly basis. Yet, there is currently a lack of any means of comparability among such platforms. While the performance of traditional database systems is well understood and measured by long-established institutions such as the Transaction Processing Performance Council (TCP), there is neither a clear definition of the performance of big data systems nor a generally agreed upon metric for comparing these systems. In this article, we describe a community-based effort for defining a big data benchmark. Over the past year, a Big Data Benchmarking Community has become established in order to fill this void. The effort focuses on defining an end-to-end application-layer benchmark for measuring the performance of big data applications, with the ability to easily adapt the benchmark specification to evolving challenges in the big data space. This article describes the efforts that have been undertaken thus far toward the definition of a BigData Top100 List. While highlighting the major technical as well as organizational challenges, through this article, we also solicit community input into this process.

A new hydrocarbon empirical potential in angle bending calculation for the molecular dynamics simulation

Energy Technology Data Exchange (ETDEWEB)

Ping, Tan Ai; Hoe, Yeak Su [Department of Mathematical Sciences, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor Bahru, Johor Darul Takzim (Malaysia)

2014-07-10

Typically, short range potential only depends on neighbouring atoms and its parameters function can be categorized into bond stretching, angle bending and bond rotation potential. In this paper, we present our work called Angle Bending (AB) potential, whereas AB potential is the extension of our previous work namely Bond Stretching (BS) potential. Basically, potential will tend to zero after truncated region, potential in specific region can be represented by different piecewise polynomial. We proposed the AB piecewise potential which is possible to solve a system involving three atoms. AB potential able to handle the potential of covalent bonds for three atoms as well as two atoms cases due to its degeneracy properties. Continuity for the piecewise polynomial has been enforced by coupling with penalty methods. There are still plenty of improvement spaces for this AB potential. The improvement for three atoms AB potential will be studied and further modified into torsional potential which are the ongoing current research.

Characterization and study of photonic crystal fibres with bends

International Nuclear Information System (INIS)

Belhadj, W.; AbdelMalek, F.; Bouchriha, H.

2006-01-01

Analysis of a photonic crystal fibre (PRCF) with bends is presented. Using the versatile finite difference time domain method, the modal characteristics of the PCFs are found. Possibilities of employing PCFs with bends in sensing are discussed. It is found that a large evanescent field is present when the bend angle exceeds 45 o

Big data, big knowledge: big data for personalized healthcare.

Science.gov (United States)

Viceconti, Marco; Hunter, Peter; Hose, Rod

2015-07-01

The idea that the purely phenomenological knowledge that we can extract by analyzing large amounts of data can be useful in healthcare seems to contradict the desire of VPH researchers to build detailed mechanistic models for individual patients. But in practice no model is ever entirely phenomenological or entirely mechanistic. We propose in this position paper that big data analytics can be successfully combined with VPH technologies to produce robust and effective in silico medicine solutions. In order to do this, big data technologies must be further developed to cope with some specific requirements that emerge from this application. Such requirements are: working with sensitive data; analytics of complex and heterogeneous data spaces, including nontextual information; distributed data management under security and performance constraints; specialized analytics to integrate bioinformatics and systems biology information with clinical observations at tissue, organ and organisms scales; and specialized analytics to define the "physiological envelope" during the daily life of each patient. These domain-specific requirements suggest a need for targeted funding, in which big data technologies for in silico medicine becomes the research priority.

BigDataBench: a Big Data Benchmark Suite from Internet Services

OpenAIRE

Wang, Lei; Zhan, Jianfeng; Luo, Chunjie; Zhu, Yuqing; Yang, Qiang; He, Yongqiang; Gao, Wanling; Jia, Zhen; Shi, Yingjie; Zhang, Shujie; Zheng, Chen; Lu, Gang; Zhan, Kent; Li, Xiaona; Qiu, Bizhu

2014-01-01

As architecture, systems, and data management communities pay greater attention to innovative big data systems and architectures, the pressure of benchmarking and evaluating these systems rises. Considering the broad use of big data systems, big data benchmarks must include diversity of data and workloads. Most of the state-of-the-art big data benchmarking efforts target evaluating specific types of applications or system software stacks, and hence they are not qualified for serving the purpo...

[Applications of eco-environmental big data: Progress and prospect].

Science.gov (United States)

Zhao, Miao Miao; Zhao, Shi Cheng; Zhang, Li Yun; Zhao, Fen; Shao, Rui; Liu, Li Xiang; Zhao, Hai Feng; Xu, Ming

2017-05-18

With the advance of internet and wireless communication technology, the fields of ecology and environment have entered a new digital era with the amount of data growing explosively and big data technologies attracting more and more attention. The eco-environmental big data is based airborne and space-/land-based observations of ecological and environmental factors and its ultimate goal is to integrate multi-source and multi-scale data for information mining by taking advantages of cloud computation, artificial intelligence, and modeling technologies. In comparison with other fields, the eco-environmental big data has its own characteristics, such as diverse data formats and sources, data collected with various protocols and standards, and serving different clients and organizations with special requirements. Big data technology has been applied worldwide in ecological and environmental fields including global climate prediction, ecological network observation and modeling, and regional air pollution control. The development of eco-environmental big data in China is facing many problems, such as data sharing issues, outdated monitoring facilities and techno-logies, and insufficient data mining capacity. Despite all this, big data technology is critical to solving eco-environmental problems, improving prediction and warning accuracy on eco-environmental catastrophes, and boosting scientific research in the field in China. We expected that the eco-environmental big data would contribute significantly to policy making and environmental services and management, and thus the sustainable development and eco-civilization construction in China in the coming decades.

Conociendo Big Data

Directory of Open Access Journals (Sweden)

Juan José Camargo-Vega

2014-12-01

Full Text Available Teniendo en cuenta la importancia que ha adquirido el término Big Data, la presente investigación buscó estudiar y analizar de manera exhaustiva el estado del arte del Big Data; además, y como segundo objetivo, analizó las características, las herramientas, las tecnologías, los modelos y los estándares relacionados con Big Data, y por último buscó identificar las características más relevantes en la gestión de Big Data, para que con ello se pueda conocer todo lo concerniente al tema central de la investigación.La metodología utilizada incluyó revisar el estado del arte de Big Data y enseñar su situación actual; conocer las tecnologías de Big Data; presentar algunas de las bases de datos NoSQL, que son las que permiten procesar datos con formatos no estructurados, y mostrar los modelos de datos y las tecnologías de análisis de ellos, para terminar con algunos beneficios de Big Data.El diseño metodológico usado para la investigación fue no experimental, pues no se manipulan variables, y de tipo exploratorio, debido a que con esta investigación se empieza a conocer el ambiente del Big Data.

Disk-bend ductility tests for irradiated materials

International Nuclear Information System (INIS)

Klueh, R.L.; Braski, D.N.

1984-01-01

We modified the HEDL disk-bend test machine and are using it to qualitatively screen alloys that are susceptible to embrittlement caused by irradiation. Tests designed to understand the disk-bend test in relation to a uniaxial test are discussed. Selected results of tests of neutron-irradiated material are also presented

BigDansing

KAUST Repository

Khayyat, Zuhair

2015-06-02

Data cleansing approaches have usually focused on detecting and fixing errors with little attention to scaling to big datasets. This presents a serious impediment since data cleansing often involves costly computations such as enumerating pairs of tuples, handling inequality joins, and dealing with user-defined functions. In this paper, we present BigDansing, a Big Data Cleansing system to tackle efficiency, scalability, and ease-of-use issues in data cleansing. The system can run on top of most common general purpose data processing platforms, ranging from DBMSs to MapReduce-like frameworks. A user-friendly programming interface allows users to express data quality rules both declaratively and procedurally, with no requirement of being aware of the underlying distributed platform. BigDansing takes these rules into a series of transformations that enable distributed computations and several optimizations, such as shared scans and specialized joins operators. Experimental results on both synthetic and real datasets show that BigDansing outperforms existing baseline systems up to more than two orders of magnitude without sacrificing the quality provided by the repair algorithms.

Influence of flock coating on bending rigidity of woven fabrics

Science.gov (United States)

Ozdemir, O.; Kesimci, M. O.

2017-10-01

This work presents the preliminary results of our efforts that focused on the effect of the flock coating on the bending rigidity of woven fabrics. For this objective, a laboratory scale flocking unit is designed and flocked samples of controlled flock density are produced. Bending rigidity of the samples with different flock densities are measured on both flocked and unflocked sides. It is shown that the bending rigidity depends on both flock density and whether the side to be measured is flocked or not. Adhesive layer thickness on the bending rigidity is shown to be dramatic. And at higher basis weights, flock density gets less effective on bending rigidity.

Hydrodynamic processes in sharp meander bends and their morphological implications

NARCIS (Netherlands)

Blanckaert, K.

2011-01-01

The migration rate of sharp meander bends exhibits large variance and indicates that some sharply curved bends tend to stabilize. These observations remain unexplained. This paper examines three hydrodynamic processes in sharp bends with fixed banks and discusses their morphological implications:

Characterizing Big Data Management

Directory of Open Access Journals (Sweden)

Rogério Rossi

2015-06-01

Full Text Available Big data management is a reality for an increasing number of organizations in many areas and represents a set of challenges involving big data modeling, storage and retrieval, analysis and visualization. However, technological resources, people and processes are crucial to facilitate the management of big data in any kind of organization, allowing information and knowledge from a large volume of data to support decision-making. Big data management can be supported by these three dimensions: technology, people and processes. Hence, this article discusses these dimensions: the technological dimension that is related to storage, analytics and visualization of big data; the human aspects of big data; and, in addition, the process management dimension that involves in a technological and business approach the aspects of big data management.

Big science

CERN Multimedia

Nadis, S

2003-01-01

" "Big science" is moving into astronomy, bringing large experimental teams, multi-year research projects, and big budgets. If this is the wave of the future, why are some astronomers bucking the trend?" (2 pages).

Capillary electrophoresis of Big-Dye terminator sequencing reactions for human mtDNA Control Region haplotyping in the identification of human remains.

Science.gov (United States)

Montesino, Marta; Prieto, Lourdes

2012-01-01

Cycle sequencing reaction with Big-Dye terminators provides the methodology to analyze mtDNA Control Region amplicons by means of capillary electrophoresis. DNA sequencing with ddNTPs or terminators was developed by (1). The progressive automation of the method by combining the use of fluorescent-dye terminators with cycle sequencing has made it possible to increase the sensibility and efficiency of the method and hence has allowed its introduction into the forensic field. PCR-generated mitochondrial DNA products are the templates for sequencing reactions. Different set of primers can be used to generate amplicons with different sizes according to the quality and quantity of the DNA extract providing sequence data for different ranges inside the Control Region.

Bending spring rate investigation of nanopipette for cell injection

Science.gov (United States)

Shen, Yajing; Zhang, Zhenhai; Fukuda, Toshio

2015-04-01

Bending of nanopipette tips during cell penetration is a major cause of cell injection failure. However, the flexural rigidity of nanopipettes is little known due to their irregular structure. In this paper, we report a quantitative method to estimate the flexural rigidity of a nanopipette by investigating its bending spring rate. First nanopipettes with a tip size of 300 nm are fabricated from various glass tubes by laser pulling followed by focused ion beam (FIB) milling. Then the bending spring rate of the nanopipettes is investigated inside a scanning electron microscope (SEM). Finally, a yeast cell penetration test is performed on these nanopipettes, which have different bending spring rates. The results show that nanopipettes with a higher bending spring rate have better cell penetration capability, which confirms that the bending spring rate may well reflect the flexural rigidity of a nanopipette. This method provides a quantitative parameter for characterizing the mechanical property of a nanopipette that can be potentially taken as a standard specification in the future. This general method can also be used to estimate other one-dimensional structures for cell injection, which will greatly benefit basic cell biology research and clinical applications.

Bending spring rate investigation of nanopipette for cell injection

International Nuclear Information System (INIS)

Shen, Yajing; Zhang, Zhenhai; Fukuda, Toshio

2015-01-01

Bending of nanopipette tips during cell penetration is a major cause of cell injection failure. However, the flexural rigidity of nanopipettes is little known due to their irregular structure. In this paper, we report a quantitative method to estimate the flexural rigidity of a nanopipette by investigating its bending spring rate. First nanopipettes with a tip size of 300 nm are fabricated from various glass tubes by laser pulling followed by focused ion beam (FIB) milling. Then the bending spring rate of the nanopipettes is investigated inside a scanning electron microscope (SEM). Finally, a yeast cell penetration test is performed on these nanopipettes, which have different bending spring rates. The results show that nanopipettes with a higher bending spring rate have better cell penetration capability, which confirms that the bending spring rate may well reflect the flexural rigidity of a nanopipette. This method provides a quantitative parameter for characterizing the mechanical property of a nanopipette that can be potentially taken as a standard specification in the future. This general method can also be used to estimate other one-dimensional structures for cell injection, which will greatly benefit basic cell biology research and clinical applications. (paper)

Aerosol deposition in bends with turbulent flow

Energy Technology Data Exchange (ETDEWEB)

McFarland, A.R.; Gong, H.; Wente, W.B. [Texas A& M Univ., College Station, TX (United States)] [and others

1997-08-01

The losses of aerosol particles in bends were determined numerically for a broad range of design and operational conditions. Experimental data were used to check the validity of the numerical model, where the latter employs a commercially available computational fluid dynamics code for characterizing the fluid flow field and Lagrangian particle tracking technique for characterizing aerosol losses. Physical experiments have been conducted to examine the effect of curvature ratio and distortion of the cross section of bends. If it curvature ratio ({delta} = R/a) is greater than about 4, it has little effect on deposition, which is in contrast with the recommendation given in ANSI N13.1-1969 for a minimum curvature ratio of 10. Also, experimental results show that if the tube cross section is flattened by 25% or less, the flattening also has little effect on deposition. Results of numerical tests have been used to develop a correlation of aerosol penetration through a bend as a function of Stokes number (Stk), curvature ratio ({delta}) and the bend angle ({theta}). 17 refs., 10 figs., 2 tabs.

Big bang and big crunch in matrix string theory

OpenAIRE

Bedford, J; Papageorgakis, C; Rodríguez-Gómez, D; Ward, J

2007-01-01

Following the holographic description of linear dilaton null Cosmologies with a Big Bang in terms of Matrix String Theory put forward by Craps, Sethi and Verlinde, we propose an extended background describing a Universe including both Big Bang and Big Crunch singularities. This belongs to a class of exact string backgrounds and is perturbative in the string coupling far away from the singularities, both of which can be resolved using Matrix String Theory. We provide a simple theory capable of...

Evaluation of spinal instrumentation rod bending characteristics for in-situ contouring.

Science.gov (United States)

Noshchenko, Andriy; Xianfeng, Yao; Armour, Grant Alan; Baldini, Todd; Patel, Vikas V; Ayers, Reed; Burger, Evalina

2011-07-01

Bending characteristics were studied in rods used for spinal instrumentation at in-situ contouring conditions. Five groups of five 6 mm diameter rods made from: cobalt alloy (VITALLIUM), titanium-aluminum-vanadium alloy (SDI™), β-titanium alloy (TNTZ), cold worked stainless steel (STIFF), and annealed stainless steel (MALLEABLE) were studied. The bending procedure was similar to that typically applied for in-situ contouring in the operating room and included two bending cycles: first--bending to 21-24° under load with further release of loading for 10 min, and second--bending to 34-37° at the previously bent site and release of load for 10 min. Applied load, bending stiffness, and springback effect were studied. Statistical evaluation included ANOVA, correlation and regression analysis. TNTZ and SDI™ rods showed the highest (p under load (p < 0.001). To reach the necessary bend angle after unloading, over bending should be 37-40% of the required angle in TNTZ and SDI™ rods, 27-30% in VITALLIUM and STIFF rods, and around 20% in MALLEABLE rods. Copyright © 2011 Wiley Periodicals, Inc.

Slice of a LEP bending magnet

CERN Multimedia

This is a slice of a LEP dipole bending magnet, made as a concrete and iron sandwich. The bending field needed in LEP is small (about 1000 Gauss), equivalent to two of the magnets people stick on fridge doors. Because it is very difficult to keep a low field steady, a high field was used in iron plates embedded in concrete. A CERN breakthrough in magnet design, LEP dipoles can be tuned easily and are cheaper than conventional magnets.

Limit moments for non circular cross-section (elliptical) pipe bends

International Nuclear Information System (INIS)

Spence, J.

1977-01-01

A number of experiment studies have been reported or are underway which investigate limit moments applied to pipe bends. Some theoretical work is also available. However, most of the work has been confined to nominally circular cross-section bends and little account has been taken of the practical problem of manufacturing tolerances. Many methods of manufacture result in bends which are not circular in cross-section but have an oval or elliptical shape. The present paper extends previous analyses on circular bends to cater for initially elliptical cross-sections. The loading is primarily in plane bending but out of plane is also considered and several independent methods are presented. No previous information is known to the authors. Upper and lower bound limit moments are derived first of all from existing linear elastic analyses and secondly upper bound moments are derived via a plastic analogy from existing stationary creep results. It is also shown that the creep information on design factors for bends can be used to obtain a reasonable estimate of the complete moment/strain behaviour of a bend or indeed a system. (Auth.)

Bliver big data til big business?

DEFF Research Database (Denmark)

Ritter, Thomas

2015-01-01

Danmark har en digital infrastruktur, en registreringskultur og it-kompetente medarbejdere og kunder, som muliggør en førerposition, men kun hvis virksomhederne gør sig klar til næste big data-bølge.......Danmark har en digital infrastruktur, en registreringskultur og it-kompetente medarbejdere og kunder, som muliggør en førerposition, men kun hvis virksomhederne gør sig klar til næste big data-bølge....

Big data uncertainties.

Science.gov (United States)

Maugis, Pierre-André G

2018-07-01

Big data-the idea that an always-larger volume of information is being constantly recorded-suggests that new problems can now be subjected to scientific scrutiny. However, can classical statistical methods be used directly on big data? We analyze the problem by looking at two known pitfalls of big datasets. First, that they are biased, in the sense that they do not offer a complete view of the populations under consideration. Second, that they present a weak but pervasive level of dependence between all their components. In both cases we observe that the uncertainty of the conclusion obtained by statistical methods is increased when used on big data, either because of a systematic error (bias), or because of a larger degree of randomness (increased variance). We argue that the key challenge raised by big data is not only how to use big data to tackle new problems, but to develop tools and methods able to rigorously articulate the new risks therein. Copyright © 2016. Published by Elsevier Ltd.

Bending mode flutter in a transonic linear cascade

Science.gov (United States)

Govardhan, Raghuraman; Jutur, Prahallada

2017-11-01

Vibration related issues like flutter pose a serious challenge to aircraft engine designers. The phenomenon has gained relevance for modern engines that employ thin and long fan blade rows to satisfy the growing need for compact and powerful engines. The tip regions of such blade rows operate with transonic relative flow velocities, and are susceptible to bending mode flutter. In such cases, the flow field around individual blades of the cascade is dominated by shock motions generated by the blade motions. In the present work, a new transonic linear cascade facility with the ability to oscillate a blade at realistic reduced frequencies has been developed. The facility operates at a Mach number of 1.3, with the central blade being oscillated in heave corresponding to the bending mode of the rotor. The susceptibility of the blade to undergo flutter at different reduced frequencies is quantified by the cycle-averaged power transfer to the blade calculated using the measured unsteady load on the oscillating blade. These measurements show fluid excitation (flutter) at low reduced frequencies and fluid damping (no flutter) at higher reduced frequencies. Simultaneous measurements of the unsteady shock motions are done with high speed shadowgraphy to elucidate the differences in shock motions between the excitation and damping cases.

HARNESSING BIG DATA VOLUMES

Directory of Open Access Journals (Sweden)

Bogdan DINU

2014-04-01

Full Text Available Big Data can revolutionize humanity. Hidden within the huge amounts and variety of the data we are creating we may find information, facts, social insights and benchmarks that were once virtually impossible to find or were simply inexistent. Large volumes of data allow organizations to tap in real time the full potential of all the internal or external information they possess. Big data calls for quick decisions and innovative ways to assist customers and the society as a whole. Big data platforms and product portfolio will help customers harness to the full the value of big data volumes. This paper deals with technical and technological issues related to handling big data volumes in the Big Data environment.

Turbulent flow computation in a circular U-Bend

Directory of Open Access Journals (Sweden)

Miloud Abdelkrim

2014-03-01

Full Text Available Turbulent flows through a circular 180° curved bend with a curvature ratio of 3.375, defined as the the bend mean radius to pipe diameter is investigated numerically for a Reynolds number of 4.45×104. The computation is performed for a U-Bend with full long pipes at the entrance and at the exit. The commercial ANSYS FLUENT is used to solve the steady Reynolds–Averaged Navier–Stokes (RANS equations. The performances of standard k-ε and the second moment closure RSM models are evaluated by comparing their numerical results against experimental data and testing their capabilities to capture the formation and extend this turbulence driven vortex. It is found that the secondary flows occur in the cross-stream half-plane of such configurations and primarily induced by high anisotropy of the cross-stream turbulent normal stresses near the outer bend.

Turbulent flow computation in a circular U-Bend

Science.gov (United States)

Miloud, Abdelkrim; Aounallah, Mohammed; Belkadi, Mustapha; Adjlout, Lahouari; Imine, Omar; Imine, Bachir

2014-03-01

Turbulent flows through a circular 180° curved bend with a curvature ratio of 3.375, defined as the the bend mean radius to pipe diameter is investigated numerically for a Reynolds number of 4.45×104. The computation is performed for a U-Bend with full long pipes at the entrance and at the exit. The commercial ANSYS FLUENT is used to solve the steady Reynolds-Averaged Navier-Stokes (RANS) equations. The performances of standard k-ɛ and the second moment closure RSM models are evaluated by comparing their numerical results against experimental data and testing their capabilities to capture the formation and extend this turbulence driven vortex. It is found that the secondary flows occur in the cross-stream half-plane of such configurations and primarily induced by high anisotropy of the cross-stream turbulent normal stresses near the outer bend.

Big bang and big crunch in matrix string theory

International Nuclear Information System (INIS)

Bedford, J.; Ward, J.; Papageorgakis, C.; Rodriguez-Gomez, D.

2007-01-01

Following the holographic description of linear dilaton null cosmologies with a big bang in terms of matrix string theory put forward by Craps, Sethi, and Verlinde, we propose an extended background describing a universe including both big bang and big crunch singularities. This belongs to a class of exact string backgrounds and is perturbative in the string coupling far away from the singularities, both of which can be resolved using matrix string theory. We provide a simple theory capable of describing the complete evolution of this closed universe

Big data a primer

CERN Document Server

Bhuyan, Prachet; Chenthati, Deepak

2015-01-01

This book is a collection of chapters written by experts on various aspects of big data. The book aims to explain what big data is and how it is stored and used. The book starts from  the fundamentals and builds up from there. It is intended to serve as a review of the state-of-the-practice in the field of big data handling. The traditional framework of relational databases can no longer provide appropriate solutions for handling big data and making it available and useful to users scattered around the globe. The study of big data covers a wide range of issues including management of heterogeneous data, big data frameworks, change management, finding patterns in data usage and evolution, data as a service, service-generated data, service management, privacy and security. All of these aspects are touched upon in this book. It also discusses big data applications in different domains. The book will prove useful to students, researchers, and practicing database and networking engineers.

An Experimental Study of Force Involved in Manual Rebar Bending Process

Science.gov (United States)

Deepu, Sasi; Vishnu, Rajendran S.; Harish, Mohan T.; Bhavani, Rao R.

2018-02-01

The work presents an experimental method of understanding the force applied during a manual rebar bending process. The study tracks the force with the variation of the angle of bend and the elapsed time from the start to the end of a complete manual rebar bending process. A sample of expert rebar bending labourers are used for conducting the experiment and the data processed to set a performance standard. If a simulator based rebar bending training can be provided for a novice, this standard can be used as a matrix to define how close a novice rebar bender is closing to the expertise.

Evaluation of bending rigidity behaviour of ultrasonic seaming on woven fabrics

Science.gov (United States)

Şevkan Macit, Ayşe; Tiber, Bahar

2017-10-01

In recent years ultrasonic seaming that is shown as an alternative method to conventional seaming has been investigated by many researchers. In our study, bending behaviour of this alternative method is examined by changing various parameters such as fabric type, seam type, roller type and seaming velocity. For this purpose fifteen types of sewn fabrics were tested according to bending rigidity test standard before and after washing processes and results were evaluated through SPSS statistical analyze programme. Consequently, bending length values of the ultrasonically sewn fabrics are found to be higher than the bending length values of conventionally sewn fabrics and the effects of seam type on bending length are seen statistically significant. Also it is observed that bending length values are in relationship with the rest of the parameters excluding roller type.

Microsoft big data solutions

CERN Document Server

Jorgensen, Adam; Welch, John; Clark, Dan; Price, Christopher; Mitchell, Brian

2014-01-01

Tap the power of Big Data with Microsoft technologies Big Data is here, and Microsoft's new Big Data platform is a valuable tool to help your company get the very most out of it. This timely book shows you how to use HDInsight along with HortonWorks Data Platform for Windows to store, manage, analyze, and share Big Data throughout the enterprise. Focusing primarily on Microsoft and HortonWorks technologies but also covering open source tools, Microsoft Big Data Solutions explains best practices, covers on-premises and cloud-based solutions, and features valuable case studies. Best of all,

Numerical simulation of laser bending of AISI 304 plate with a ...

African Journals Online (AJOL)

Keywords: laser bending; process modeling; bending angle; response surface models. ... (Shi et al., 2007) presented numerical simulation of bending for with different shapes of laser ..... Matlab 2011a application code is used to develop and.

Summary big data

CERN Document Server

2014-01-01

This work offers a summary of Cukier the book: "Big Data: A Revolution That Will Transform How we Live, Work, and Think" by Viktor Mayer-Schonberg and Kenneth. Summary of the ideas in Viktor Mayer-Schonberg's and Kenneth Cukier's book: " Big Data " explains that big data is where we use huge quantities of data to make better predictions based on the fact we identify patters in the data rather than trying to understand the underlying causes in more detail. This summary highlights that big data will be a source of new economic value and innovation in the future. Moreover, it shows that it will

Magnetic field of longitudinal gradient bend

Science.gov (United States)

Aiba, Masamitsu; Böge, Michael; Ehrlichman, Michael; Streun, Andreas

2018-06-01

The longitudinal gradient bend is an effective method for reducing the natural emittance in light sources. It is, however, not a common element. We have analyzed its magnetic field and derived a set of formulae. Based on the derivation, we discuss how to model the longitudinal gradient bend in accelerator codes that are used for designing electron storage rings. Strengths of multipole components can also be evaluated from the formulae, and we investigate the impact of higher order multipole components in a very low emittance lattice.

Bending energy of buckled edge dislocations

Science.gov (United States)

Kupferman, Raz

2017-12-01

The study of elastic membranes carrying topological defects has a longstanding history, going back at least to the 1950s. When allowed to buckle in three-dimensional space, membranes with defects can totally relieve their in-plane strain, remaining with a bending energy, whose rigidity modulus is small compared to the stretching modulus. In this paper we study membranes with a single edge dislocation. We prove that the minimum bending energy associated with strain-free configurations diverges logarithmically with the size of the system.

Magnetically Assisted Bilayer Composites for Soft Bending Actuators

Directory of Open Access Journals (Sweden)

Sung-Hwan Jang

2017-06-01

Full Text Available This article presents a soft pneumatic bending actuator using a magnetically assisted bilayer composite composed of silicone polymer and ferromagnetic particles. Bilayer composites were fabricated by mixing ferromagnetic particles to a prepolymer state of silicone in a mold and asymmetrically distributed them by applying a strong non-uniform magnetic field to one side of the mold during the curing process. The biased magnetic field induces sedimentation of the ferromagnetic particles toward one side of the structure. The nonhomogeneous distribution of the particles induces bending of the structure when inflated, as a result of asymmetric stiffness of the composite. The bilayer composites were then characterized with a scanning electron microscopy and thermogravimetric analysis. The bending performance and the axial expansion of the actuator were discussed for manipulation applications in soft robotics and bioengineering. The magnetically assisted manufacturing process for the soft bending actuator is a promising technique for various applications in soft robotics.

Magnetically Assisted Bilayer Composites for Soft Bending Actuators.

Science.gov (United States)

Jang, Sung-Hwan; Na, Seon-Hong; Park, Yong-Lae

2017-06-12

This article presents a soft pneumatic bending actuator using a magnetically assisted bilayer composite composed of silicone polymer and ferromagnetic particles. Bilayer composites were fabricated by mixing ferromagnetic particles to a prepolymer state of silicone in a mold and asymmetrically distributed them by applying a strong non-uniform magnetic field to one side of the mold during the curing process. The biased magnetic field induces sedimentation of the ferromagnetic particles toward one side of the structure. The nonhomogeneous distribution of the particles induces bending of the structure when inflated, as a result of asymmetric stiffness of the composite. The bilayer composites were then characterized with a scanning electron microscopy and thermogravimetric analysis. The bending performance and the axial expansion of the actuator were discussed for manipulation applications in soft robotics and bioengineering. The magnetically assisted manufacturing process for the soft bending actuator is a promising technique for various applications in soft robotics.

Water Management for Competing Uses: Environmental Flows in the Transboundary Rio Grande/Rio Bravo

Science.gov (United States)

Sandoval Solis, S.; McKinney, D. C.

2011-12-01

Introduction Due to high water demand, the scarcity of water, and the complexity of water allocation, environmental flows have not been considered as an integral part of the water management in the Rio Grande/Rio Bravo transboundary basin. The Big Bend reach is located between the cities of Presidio/Ojinaga to Amistad international reservoir, along the main stream (Fig. 1). Important environmental habitats such as the Big Bend National and State Park in the U.S., the Maderas del Carmen, Cañon de Santa Elena and Ocampo natural reserved areas in Mexico are ecologically threatened because of the lack of environmental water management policies. Several efforts have been undertaken by scientists, government agencies and NGOs to determine the environmental flows for this reach and water management policies that can provide these flows. Objective The objective of this research is to describe a water management policy that can conciliate environmental and human water uses in the Big Bend region. In other words, define a policy that can provide environmental flows without harming water supply for stakeholders or increasing flood risk, within legal and physical constraints of the system. Methodology First, the system was characterized identifying water users, hydraulic infrastructure, and water allocation according to state, federal and international regulations. Second, a hydrograph for environmental flows was proposed that mimics the hydrologic characteristics of the prior dam alteration. Third, a water planning model was constructed to evaluate alternative policies. Fourth, the water management is proposed to provide environmental restoration flows from Luis L. Leon reservoir. This policy considers mechanisms that reduce flooding and drought risks, while meting national and international water regulations. Results Three types of natural flow regimes are considered: (1) median flows aimed to provide the base flow in the region, (2) high flows to provide transversal

Effect of Bend Radius on Magnitude and Location of Erosion in S-Bend

Directory of Open Access Journals (Sweden)

Quamrul H. Mazumder

2015-01-01

Full Text Available Solid particle erosion is a mechanical process that removes material by the impact of solid particles entrained in the flow. Erosion is a leading cause of failure of oil and gas pipelines and fittings in fluid handling industries. Different approaches have been used to control or minimize damage caused by erosion in particulated gas-solid or liquid-solid flows. S-bend geometry is widely used in different fluid handling equipment that may be susceptible to erosion damage. The results of a computational fluid dynamic (CFD simulation of diluted gas-solid and liquid-solid flows in an S-bend are presented in this paper. In addition to particle impact velocity, the bend radius may have significant influence on the magnitude and the location of erosion. CFD analysis was performed at three different air velocities (15.24 m/s–45.72 m/s and three different water velocities (0.1 m/s–10 m/s with entrained solid particles. The particle sizes used in the analysis range between 50 and 300 microns. Maximum erosion was observed in water with 10 m/s, 250-micron particle size, and a ratio of 3.5. The location of maximum erosion was observed in water with 10 m/s, 300-micron particle size, and a ratio of 3.5. Comparison of CFD results with available literature data showed reasonable and good agreement.

Galvanic vestibular stimulation may improve anterior bending posture in Parkinson's disease.

Science.gov (United States)

Okada, Yohei; Kita, Yorihiro; Nakamura, Junji; Kataoka, Hiroshi; Kiriyama, Takao; Ueno, Satoshi; Hiyamizu, Makoto; Morioka, Shu; Shomoto, Koji

2015-05-06

This study investigated the effects of binaural monopolar galvanic vestibular stimulation (GVS), which likely stimulates the bilateral vestibular system, on the anterior bending angle in patients with Parkinson's disease (PD) with anterior bending posture in a single-blind, randomized sham-controlled crossover trial. The seven PD patients completed two types of stimulation (binaural monopolar GVS and sham stimulation) applied in a random order 1 week apart. We measured each patient's anterior bending angles while he or she stood with eyes open and eyes closed before/after the stimulations. The anterior bending angles in both the eyes-open and the eyes-closed conditions were significantly reduced after the GVS. The amount of change in the eyes-closed condition post-GVS was significantly larger than that by sham stimulation. The amount of change in anterior bending angles in the GVS condition was not significantly correlated with Unified Parkinson's Disease Rating Scale motor score, disease duration, the duration of the postural deformities, and the anterior bending angles before the GVS. Binaural monopolar GVS might improve anterior bending posture in PD patients, irrespective of the duration and the severity of disease and postural deformities. Binaural monopolar GVS might be a novel treatment strategy to improve anterior bending posture in PD.

Study of Transport and Micro-structural properties of Magnesium Di-Boride Strand under react and bend mode and bend and react mode

International Nuclear Information System (INIS)

Kundu, Ananya; Kumar Das, Subrat; Bano, Anees; Pradhan, Subrata

2017-01-01

I-V characterization of commercial multi-filamentary Magnesium Di-Boride (MgB 2 ) wire of diameter 0.83 mm were studied in Cryocooler at self-field I-V characterization system under both react and bend mode and bend and react mode for a range of temperature 6 K - 25 K. This study is of practical technical relevance where the heat treatment of the superconducting wire makes the wire less flexible for winding in magnet and in other applications. In the present work the bending diameter was varied from 40 mm to 20 mm and for each case critical current (I c ) of the strand is measured for above range of temperature. A customized sample holder is fabricated and thermally anchored with the 2 nd cold stage of Cryocooler. It is observed from the measurement that the strand is more susceptible to degradation for react and bend cases. The transport measurement of the strand was accompanied by SEM analyses of bend samples. Also the tensile strength of the raw strands and the heat treated strands were carried out at room temperature in Universal Testing Machine (UTM) to have an estimate about the limiting winding tension value during magnet fabrication. (paper)

Four-Point Bending Strength Testing of Pultruded Fiberglass Composite Wind Turbine Blade Sections

International Nuclear Information System (INIS)

Musial, W.; Bourne, B; Hughes, S; Zuteck, M. D.

2001-01-01

The ultimate strength of the PS Enterprises pultruded blade section was experimentally determined under four-point bending at the National Renewable Energy Laboratory. Thirteen 8-foot long full-scale blade segments were individually tested to determine their maximum moment carrying capability. Three airfoil-bending configurations were tested: high- and low-pressure skin buckling, and low pressure skin buckling with foam interior reinforcement. Maximum strain was recorded for each sample on the compressive and tensile surfaces of each test blade. Test data are compared to the results of three analytical buckling prediction methods. Based on deviations from the linear strain versus load curve, data indicate a post-buckling region. High-pressure side buckling occurred sooner than low-pressure side buckling. The buckling analyses were conservative for both configurations, but high-pressure side buckling in particular was substantially under-predicted. Both high- and low-pressure buckling configurations had very similar failure loads. These results suggests that a redundant load path may be providing strength to the section in the post-buckling region, making the onset of panel buckling a poor predictor of ultimate strength for the PS Enterprises pultrusion

Molecular Mechanics of the α-Actinin Rod Domain: Bending, Torsional, and Extensional Behavior

Science.gov (United States)

Golji, Javad; Collins, Robert; Mofrad, Mohammad R. K.

2009-01-01

α-Actinin is an actin crosslinking molecule that can serve as a scaffold and maintain dynamic actin filament networks. As a crosslinker in the stressed cytoskeleton, α-actinin can retain conformation, function, and strength. α-Actinin has an actin binding domain and a calmodulin homology domain separated by a long rod domain. Using molecular dynamics and normal mode analysis, we suggest that the α-actinin rod domain has flexible terminal regions which can twist and extend under mechanical stress, yet has a highly rigid interior region stabilized by aromatic packing within each spectrin repeat, by electrostatic interactions between the spectrin repeats, and by strong salt bridges between its two anti-parallel monomers. By exploring the natural vibrations of the α-actinin rod domain and by conducting bending molecular dynamics simulations we also predict that bending of the rod domain is possible with minimal force. We introduce computational methods for analyzing the torsional strain of molecules using rotating constraints. Molecular dynamics extension of the α-actinin rod is also performed, demonstrating transduction of the unfolding forces across salt bridges to the associated monomer of the α-actinin rod domain. PMID:19436721

Shakedown boundary determination of a 90° back-to-back pipe bend subjected to steady internal pressures and cyclic in-plane bending moments

International Nuclear Information System (INIS)

Abdalla, Hany F.

2014-01-01

No experimental data exist within open literature, to the best knowledge of the author, for determining shakedown boundaries of 90° back-to-back pipe bends. Ninety degree back-to-back pipe bends are extensively utilized within piping networks of nuclear submarines and modern turbofan aero-engines where space limitation is considered a paramount concern. In the current research, the 90° back-to-back pipe bend setup analyzed is subjected to a spectrum of steady internal pressures and cyclic in-plane bending moments. A previously developed direct non-cyclic simplified technique for determining elastic shakedown limit loads is utilized to generate the elastic shakedown boundary of the analyzed structure. The simplified technique outcomes showed excellent correlation with the results of full elastic–plastic cyclic loading finite element simulations. - Highlights: • No shakedown experimental data exist for 90° back-to-back pipe bends. • A non-cyclic technique is utilized to generate the elastic shakedown boundary. • The non-cyclic technique succeeded in generating the structure's Bree diagram. • The non-cyclic technique correlated well with full cyclic loading FE simulations

A comparison of plastic collapse and limit loads for single mitred pipe bends under in-plane bending

International Nuclear Information System (INIS)

Neilson, R.; Wood, J.; Hamilton, R.; Li, H.

2010-01-01

This paper presents a comparison of the plastic collapse loads from experimental in-plane bending tests on three 90 o single un-reinforced mitred pipe bends, with the results from various 3D solid finite element models. The bending load applied reduced the bend angle and in turn, the resulting cross-sectional ovalisation led to a recognised weakening mechanism. In addition, at maximum load there was a reversal in stiffness, characteristic of buckling. This reversal in stiffness was accompanied by significant ovalisation and plasticity at the mitre intersection. Both the weakening mechanism and the post-buckling behaviour are only observable by testing or by including large displacement effects in the plastic finite element solution. A small displacement limit solution with an elastic-perfectly plastic material model overestimated the collapse load by more than 40% and could not reproduce the buckling behaviour. The plastic collapse finite element solution, with large displacements, produced excellent agreement with the experiment. Sufficient experimental detail is presented for these results to be used as a benchmark for analysts in this area. Given the robustness of non-linear solutions in commercial finite element codes and the ready availability of computing resources, it is argued that pressure vessel code developers should now be recommending large displacement analysis as the default position for limit and plastic collapse analyses, rather than expecting engineers to anticipate weakening mechanisms and related non-linear phenomena.

Spontaneous bending of 2D molecular bottle-brush

NARCIS (Netherlands)

Subbotin, A; Jong, J; ten Brinke, G

Using a scaling approach we consider a 2D comb copolymer brush under bending deformations. We show that the rectilinear brush is locally stable and can be characterized by a persistence length lambda increasing with the molecular weight of grafting side chains as lambda similar to M-3. A bending

Rotating Square-Ended U-Bend Using Low-Reynolds-Number Models

Directory of Open Access Journals (Sweden)

Konstantinos-Stephen P. Nikas

2005-01-01

bend is better reproduced by the low-Re models. Turbulence levels within the rotating U-bend are underpredicted, but DSM models produce a more realistic distribution. Along the leading side, all models overpredict heat transfer levels just after the bend. Along the trailing side, the heat transfer predictions of the low-Re DSM with the NYap, are close to the measurements.

Transient analysis of air-water two-phase flow in channels and bends

International Nuclear Information System (INIS)

Khan, H.J.; Ye, W.; Pertmer, G.A.

1992-01-01

The algorithm used in this paper is the Newton Block Gauss Seidel method, which has been applied to both simple and complex flow conditions in two-phase flow. This paper contains a description of difference techniques and an iterative solution algorithm that is used to solve the field and constitutive equations of the two-fluid model. In practice, this solution procedure has been proven to be stable and capable of generating solutions in problems where other schemes have failed. The method converges rapidly for reasonable error tolerances and is easily extended to three-dimensional geometries. Using air-water as the two-phase medium, transient flow behavior in several geometries of interest are shown. Flow through a vertical channel with flow obstruction, large U bends, and 90-deg bends are being demonstrated with variation of inlet void fraction and slip ratio. Significant changes in the velocity and void distribution profiles have been observed. Various regions of flow recirculation are obtained in the flow domain for each phase. The phasic velocity and void distributions are dominated by gravity-induced phase separation causing air to accumulate in the upper region. The influence of inlet slip ratio and interfacial momentum transfer on the transient flow profile has been demonstrated in detail

Big Data en surveillance, deel 1 : Definities en discussies omtrent Big Data

NARCIS (Netherlands)

Timan, Tjerk

2016-01-01

Naar aanleiding van een (vrij kort) college over surveillance en Big Data, werd me gevraagd iets dieper in te gaan op het thema, definities en verschillende vraagstukken die te maken hebben met big data. In dit eerste deel zal ik proberen e.e.a. uiteen te zetten betreft Big Data theorie en

Characterizing Big Data Management

OpenAIRE

Rogério Rossi; Kechi Hirama

2015-01-01

Big data management is a reality for an increasing number of organizations in many areas and represents a set of challenges involving big data modeling, storage and retrieval, analysis and visualization. However, technological resources, people and processes are crucial to facilitate the management of big data in any kind of organization, allowing information and knowledge from a large volume of data to support decision-making. Big data management can be supported by these three dimensions: t...

Study of transport and micro-structural properties of magnesium di-boride strand under react and bend mode and bend and react mode

International Nuclear Information System (INIS)

Kundu, Ananya; Das, Subrat Kumar; Bano, Anees; Pradhan, Subrata

2015-01-01

I-V characterization of commercial multi-filamentary Magnesium Di-Boride (MgB 2 ) wire of diameter 0.83 mm were studied in cryocooler based self-field characterization system under both react and bent mode and bent and react mode for a range of temperature 6 K - 25 K. This study is of practical technical relevance where the heat treatment of the superconducting wire makes the sample less flexible for winding in magnet and in other applications. There are limited reported data, available on degradation of MgB 2 wire with bending induced strain in react and wind and wind and react method. In the present work the bending diameter were varied from 80 mm to 20 mm in the interval of 10 mm change of bending diameter and for each case critical current (Ic) of the strand is measured for the above range of temperature. An ETP copper made customized sample holder for mounting the MgB 2 strand was fabricated and is thermally anchored to the cooling stage of the cryocooler. It is seen from the experimental data that in react and bent mode the critical current degrades from 105 A to 87 A corresponding to bending diameter of 80 mm and 20 mm respectively. The corresponding bending strain was analytically estimated and compared with the simulation result. It is also observed that in react and bent mode, the degradation of the transport property of the strand is less as compared to react and bent mode. For bent and react mode in the same sample, the critical current (Ic) was measured to be ∼145 A at 15 K for bending diameter of 20 mm. Apart from studying the bending induced strain on MgB 2 strand, the tensile test of the strand at RT was carried out. The electrical characterizations of the samples were accompanied by the microstructure analyses of the bent strand to examine the bending induced degradation in the grain structure of the strand. All these experimental findings are expected to be used as input to fabricate prototype MgB 2 based magnet. (author)

Tubular lining material for pipelines having bends

Energy Technology Data Exchange (ETDEWEB)

Moringa, A.; Sakaguchi, Y.; Hyodo, M.; Yagi, I.

1987-03-24

A tubular lining material for pipelines having bends or curved portions comprises a tubular textile jacket made of warps and wefts woven in a tubular form overlaid with a coating of a flexible synthetic resin. It is applicable onto the inner surface of a pipeline having bends or curved portions in such manner that the tubular lining material with a binder onto the inner surface thereof is inserted into the pipeline and allowed to advance within the pipeline, with or without the aid of a leading rope-like elongated element, while turning the tubular lining material inside out under fluid pressure. In this manner the tubular lining material is applied onto the inner surface of the pipeline with the binder being interposed between the pipeline and the tubular lining material. The lining material is characterized in that a part of all of the warps are comprised of an elastic yarn around which, over the full length thereof, a synthetic fiber yarn or yarns have been left-and/or right-handedly coiled. This tubular lining material is particularly suitable for lining a pipeline having an inner diameter of 25-200 mm and a plurality of bends, such as gas service pipelines or house pipelines, without occurrence of wrinkles in the lining material in a bend.

Fuzzy model for Laser Assisted Bending Process

Directory of Open Access Journals (Sweden)

Giannini Oliviero

2016-01-01

Full Text Available In the present study, a fuzzy model was developed to predict the residual bending in a conventional metal bending process assisted by a high power diode laser. The study was focused on AA6082T6 aluminium thin sheets. In most dynamic sheet metal forming operations, the highly nonlinear deformation processes cause large amounts of elastic strain energy stored in the formed material. The novel hybrid forming process was thus aimed at inducing the local heating of the mechanically bent workpiece in order to decrease or eliminate the related springback phenomena. In particular, the influence on the extent of springback phenomena of laser process parameters such as source power, scan speed and starting elastic deformation of mechanically bent sheets, was experimentally assessed. Consistent trends in experimental response according to operational parameters were found. Accordingly, 3D process maps of the extent of the springback phenomena according to operational parameters were constructed. The effect of the inherent uncertainties on the predicted residual bending caused by the approximation in the model parameters was evaluated. In particular, a fuzzy-logic based approach was used to describe the model uncertainties and the transformation method was applied to propagate their effect on the residual bending.

Inflationary and deflationary branches in extended pre-big-bang cosmology

International Nuclear Information System (INIS)

Lidsey, J.E.

1997-01-01

The pre-big-bang cosmological scenario is studied within the context of the Brans-Dicke theory of gravity. An epoch of superinflationary expansion may occur in the pre-big-bang phase of the Universe close-quote s history in a certain region of parameter space. Two models are considered that contain a cosmological constant in the gravitational and matter sectors of the theory, respectively. Classical pre- and post-big-bang solutions are found for both models. The existence of a curvature singularity forbids a classical transition between the two branches. On the other hand, a quantum cosmological approach based on the tunneling boundary condition results in a nonzero transition probability. The transition may be interpreted as a spatial reflection of the wave function in minisuperspace. copyright 1997 The American Physical Society

Inflationary and deflationary branches in extended pre-big-bang cosmology

Energy Technology Data Exchange (ETDEWEB)

Lidsey, J.E. [Astronomy Unit, School of Mathematical Sciences, Queen Mary Westfield, Mile End Road, London, E1 4NS (United Kingdom)

1997-03-01

The pre-big-bang cosmological scenario is studied within the context of the Brans-Dicke theory of gravity. An epoch of superinflationary expansion may occur in the pre-big-bang phase of the Universe{close_quote}s history in a certain region of parameter space. Two models are considered that contain a cosmological constant in the gravitational and matter sectors of the theory, respectively. Classical pre- and post-big-bang solutions are found for both models. The existence of a curvature singularity forbids a classical transition between the two branches. On the other hand, a quantum cosmological approach based on the tunneling boundary condition results in a nonzero transition probability. The transition may be interpreted as a spatial reflection of the wave function in minisuperspace. {copyright} {ital 1997} {ital The American Physical Society}

Bending of metal-filled carbon nanotube under electron beam irradiation

Directory of Open Access Journals (Sweden)

Abha Misra

2012-03-01

Full Text Available Electron beam irradiation induced, bending of Iron filled, multiwalled carbon nanotubes is reported. Bending of both the carbon nanotube and the Iron contained within the core was achieved using two approaches with the aid of a high resolution electron microscope (HRTEM. In the first approach, bending of the nanotube structure results in response to the irradiation of a pristine kink defect site, while in the second approach, disordered sites induce bending by focusing the electron beam on the graphite walls. The HRTEM based in situ observations demonstrate the potential for using electron beam irradiation to investigate and manipulate the physical properties of confined nanoscale structures.

Big Data in der Cloud

DEFF Research Database (Denmark)

Leimbach, Timo; Bachlechner, Daniel

2014-01-01

Technology assessment of big data, in particular cloud based big data services, for the Office for Technology Assessment at the German federal parliament (Bundestag)......Technology assessment of big data, in particular cloud based big data services, for the Office for Technology Assessment at the German federal parliament (Bundestag)...

An analysis of cross-sectional differences in big and non-big public accounting firms' audit programs

NARCIS (Netherlands)

Blokdijk, J.H. (Hans); Drieenhuizen, F.; Stein, M.T.; Simunic, D.A.

2006-01-01

A significant body of prior research has shown that audits by the Big 5 (now Big 4) public accounting firms are quality differentiated relative to non-Big 5 audits. This result can be derived analytically by assuming that Big 5 and non-Big 5 firms face different loss functions for "audit failures"

Big Data is invading big places as CERN

CERN Multimedia

CERN. Geneva

2017-01-01

Big Data technologies are becoming more popular with the constant grow of data generation in different fields such as social networks, internet of things and laboratories like CERN. How is CERN making use of such technologies? How machine learning is applied at CERN with Big Data technologies? How much data we move and how it is analyzed? All these questions will be answered during the talk.

The big bang

International Nuclear Information System (INIS)

Chown, Marcus.

1987-01-01

The paper concerns the 'Big Bang' theory of the creation of the Universe 15 thousand million years ago, and traces events which physicists predict occurred soon after the creation. Unified theory of the moment of creation, evidence of an expanding Universe, the X-boson -the particle produced very soon after the big bang and which vanished from the Universe one-hundredth of a second after the big bang, and the fate of the Universe, are all discussed. (U.K.)

Incomplete (bending) fractures of the mandibular condyle in children

International Nuclear Information System (INIS)

Ahrendt, D.; Swischuk, L.E.; Hayden, C.K. Jr.; Texas Univ., Galveston

1984-01-01

Incomplete, bending or bowing fractures of the mandibular condyle in children frequently go undetected. The reason is that the bending deformity often is subtle and passes for normal. This is especially true if the fractures are bilateral. (orig.)

77 FR 5628 - Requested Administrative Waiver of the Coastwise Trade Laws: Vessel BIG GAME; Invitation for...

Science.gov (United States)

2012-02-03

... Administrative Waiver of the Coastwise Trade Laws: Vessel BIG GAME; Invitation for Public Comments AGENCY....gov . SUPPLEMENTARY INFORMATION: As described by the applicant the intended service of the vessel BIG GAME is: Intended Commercial Use of Vessel: ``Fishing charter boat.'' Geographic Region: ``Rhode Island...

Bolted flanged connections subjected to longitudinal bending moments

International Nuclear Information System (INIS)

Blach, A.E.

1992-01-01

Flanges in piping systems and also pressure vessel flanges on tall columns are often subjected to longitudinal bending moments of considerable magnitude, be it from thermal expansion stresses in piping systems or from wind or seismic loadings on tall vertical pressure vessels. Except for the ASME Code, Section III, Subsections NB, NC, and ND, other pressure vessel and piping codes do not contain design ASME Nuclear Power Plant Code (Section III), an empirical formula is given, expressing a longitudinal bending moment in bolted flanged connections in terms of an equivalent internal pressure to be added to the design pressure of the flange. In this paper, an attempt is made to analyse the stresses on flanges and bolting due to external bending moments and to compare flange thicknesses thus obtained with thicknesses required using the equivalent design pressure specified in Subsections NB, NC, and ND. A design method is proposed, based on analysis and experimental work, which may be suitable for flange bending moment analysis when the rules of the Nuclear Power Plant Code are not mandatory. (orig.)

Small Big Data Congress 2017

NARCIS (Netherlands)

Doorn, J.

2017-01-01

TNO, in collaboration with the Big Data Value Center, presents the fourth Small Big Data Congress! Our congress aims at providing an overview of practical and innovative applications based on big data. Do you want to know what is happening in applied research with big data? And what can already be

Big data opportunities and challenges

CERN Document Server

2014-01-01

This ebook aims to give practical guidance for all those who want to understand big data better and learn how to make the most of it. Topics range from big data analysis, mobile big data and managing unstructured data to technologies, governance and intellectual property and security issues surrounding big data.

Longitudinal-bending mode micromotor using multilayer piezoelectric actuator.

Science.gov (United States)

Yao, K; Koc, B; Uchino, K

2001-07-01

Longitudinal-bending mode ultrasonic motors with a diameter of 3 mm were fabricated using stacked multilayer piezoelectric actuators, which were self-developed from hard lead zirconate titanate (PZT) ceramic. A bending vibration was converted from a longitudinal vibration with a longitudinal-bending coupler. The motors could be bidirectionally operated by changing driving frequency. Their starting and braking torque were analyzed based on the transient velocity response. With a load of moment of inertia 2.5 x 10(-7) kgm2, the motor showed a maximum starting torque of 127.5 microNm. The braking torque proved to be a constant independent on the motor's driving conditions and was roughly equivalent to the maximum starting torque achievable with our micromotors.

Bending-active reciprocal structures based on equilateral polyhedral geometries

DEFF Research Database (Denmark)

Popovic Larsen, Olga; BRANCART, Stijn; DE TEMMERMAN, Niels

2017-01-01

As mutually supported beam structures, reciprocal frames limit the number of components that are joined at each connection to two. However, this system of intermediate connections introduces undesirable bending moments in the beam elements. By utilising elastic deformation to create curved...... of parts of reciprocal bending-active components based on a selection of polyhedral dome types. To simplify the assembly of the structures and avoid the manual bending of the components on site, we introduce the concept of a double-layered, pre-bent component. Finally, this paper presents the development...

Big Data and Neuroimaging.

Science.gov (United States)

Webb-Vargas, Yenny; Chen, Shaojie; Fisher, Aaron; Mejia, Amanda; Xu, Yuting; Crainiceanu, Ciprian; Caffo, Brian; Lindquist, Martin A

2017-12-01

Big Data are of increasing importance in a variety of areas, especially in the biosciences. There is an emerging critical need for Big Data tools and methods, because of the potential impact of advancements in these areas. Importantly, statisticians and statistical thinking have a major role to play in creating meaningful progress in this arena. We would like to emphasize this point in this special issue, as it highlights both the dramatic need for statistical input for Big Data analysis and for a greater number of statisticians working on Big Data problems. We use the field of statistical neuroimaging to demonstrate these points. As such, this paper covers several applications and novel methodological developments of Big Data tools applied to neuroimaging data.

Big Data; A Management Revolution : The emerging role of big data in businesses

OpenAIRE

Blasiak, Kevin

2014-01-01

Big data is a term that was coined in 2012 and has since then emerged to one of the top trends in business and technology. Big data is an agglomeration of different technologies resulting in data processing capabilities that have been unreached before. Big data is generally characterized by 4 factors. Volume, velocity and variety. These three factors distinct it from the traditional data use. The possibilities to utilize this technology are vast. Big data technology has touch points in differ...

Priming the Pump for Big Data at Sentara Healthcare.

Science.gov (United States)

Kern, Howard P; Reagin, Michael J; Reese, Bertram S

2016-01-01

Today's healthcare organizations are facing significant demands with respect to managing population health, demonstrating value, and accepting risk for clinical outcomes across the continuum of care. The patient's environment outside the walls of the hospital and physician's office-and outside the electronic health record (EHR)-has a substantial impact on clinical care outcomes. The use of big data is key to understanding factors that affect the patient's health status and enhancing clinicians' ability to anticipate how the patient will respond to various therapies. Big data is essential to delivering sustainable, highquality, value-based healthcare, as well as to the success of new models of care such as clinically integrated networks (CINs) and accountable care organizations.Sentara Healthcare, based in Norfolk, Virginia, has been an early adopter of the technologies that have readied us for our big data journey: EHRs, telehealth-supported electronic intensive care units, and telehealth primary care support through MDLIVE. Although we would not say Sentara is at the cutting edge of the big data trend, it certainly is among the fast followers. Use of big data in healthcare is still at an early stage compared with other industries. Tools for data analytics are maturing, but traditional challenges such as heightened data security and limited human resources remain the primary focus for regional health systems to improve care and reduce costs. Sentara primarily makes actionable use of big data in our CIN, Sentara Quality Care Network, and at our health plan, Optima Health. Big data projects can be expensive, and justifying the expense organizationally has often been easier in times of crisis. We have developed an analytics strategic plan separate from but aligned with corporate system goals to ensure optimal investment and management of this essential asset.

Negative-mass lagging cores of the big bang

International Nuclear Information System (INIS)

Miller, B.D.

1976-01-01

Examples are given of spherically symmetric cosmological models containing space-sections with the following properties: at large values of the geometrically defined coordinate R, the mass is positive, while at small values of R, the mass is negative. The negative-mass region of spacetime has local properties similar to those of the negative-mass Schwarzschild solution. The big bang in these models is partially spacelike and partially timelike, so the spacetimes do not obey the strong form of the cosmic censorship hypothesis. The timelike, negative-mass segments of the big bang are unlimited sources of electromagnetic and gravitational radiation, and as such may be attractive as ''lagging core'' models of highly energetic astrophysical phenomena

Negative-mass lagging cores of the big bang

Energy Technology Data Exchange (ETDEWEB)

Miller, B.D.

1976-09-01

Examples are given of spherically symmetric cosmological models containing space-sections with the following properties: at large values of the geometrically defined coordinate R, the mass is positive, while at small values of R, the mass is negative. The negative-mass region of spacetime has local properties similar to those of the negative-mass Schwarzschild solution. The big bang in these models is partially spacelike and partially timelike, so the spacetimes do not obey the strong form of the cosmic censorship hypothesis. The timelike, negative-mass segments of the big bang are unlimited sources of electromagnetic and gravitational radiation, and as such may be attractive as ''lagging core'' models of highly energetic astrophysical phenomena. (AIP)

Social big data mining

CERN Document Server

Ishikawa, Hiroshi

2015-01-01

Social Media. Big Data and Social Data. Hypotheses in the Era of Big Data. Social Big Data Applications. Basic Concepts in Data Mining. Association Rule Mining. Clustering. Classification. Prediction. Web Structure Mining. Web Content Mining. Web Access Log Mining, Information Extraction and Deep Web Mining. Media Mining. Scalability and Outlier Detection.

Effect of contouring on bending structural stiffness and bending strength of the 3.5 titanium SOP implant.

Science.gov (United States)

Rutherford, Scott; Ness, Malcolm G

2012-11-01

To compare the bending structural stiffness (BSS) and bending strength (BS) of the 3.5 titanium (Ti) string of pearls (SOP) plate and the 3.5 316LVM stainless steel SOP plate; and the effect of contouring on the BSS and BS of the 3.5 Ti SOP plate. In vitro experimental static 4-point bending materials testing. Twenty-five 3.5 mm Ti and five 3.5 mm 316LVM stainless steel SOP locking bone plates. Each plate was tested in 4-point bending until 10 mm of displacement was achieved. BSS and BS were then calculated for each plate. A 2-sample t-test was used to compare the mean BSS and BS of the different groups. The 3.5 Ti SOP plate had lower mean BSS (0.00263 Nm(2) ) but similar mean BS (12.8 Nm) when compared to the 3.5 316LVM SOP (0.00402 Nm(2) , 13.0 Nm). Prebending the 3.5 Ti SOP diminished its mean BSS (0.00224 Nm(2) ) and mean BS (9.4 Nm) when compared to the Ti control. Pretwisting the 3.5 Ti SOP increased its mean BSS (0.00273 Nm(2) ) but decreased its mean BS (12.4 Nm) when compared to the Ti control. The 3.5 Ti SOP is less stiff but of similar strength to the 3.5 316LVM stainless steel SOP. Prebending the Ti SOP significantly lowers its stiffness and strength. Pretwisting the SOP actually increases its stiffness but slightly lowers its strength. © Copyright 2012 by The American College of Veterinary Surgeons.

Ligament rupture and unstable burst behaviors of axial flaws in steam generator U-bends

Energy Technology Data Exchange (ETDEWEB)

Bahn, Chi Bum, E-mail: bahn@pusan.ac.kr [Pusan National University, 2 Busandaehak-ro 63 beon-gil, Geumjeong-gu, Busan 609-735 (Korea, Republic of); Oh, Young-Jin [KEPCO Engineering & Construction Co. Inc., Seongnam 463-870 (Korea, Republic of); Majumdar, Saurin [Argonne National Laboratory, Lemont, IL 60439 (United States)

2015-11-15

Highlights: • Ligament rupture and unstable burst pressure tests were conducted with U-bends. • In general, U-bends showed higher ligament rupture and burst pressures than straight tubes. • U-bend test data was bounded by 90% lower limit of the probabilistic models for straight tubes. • Prediction models for straight tubes could be conservatively applied to U-bends. - Abstract: Incidents of U-bend cracking in steam generator (SG) tubes have been reported, some of which have led to tube rupture. Experimental and analytical modeling efforts to determine the failure criteria of flawed SG U-bends are limited. To evaluate structural integrity of flawed U-bends, ligament rupture and unstable burst pressure tests were conducted on 57 and 152 mm bend radius U-bends with axial electrical discharge machining notches. In general, the ligament rupture and burst pressures of the U-bends were higher than those of straight tubes with similar notches. To quantitatively address the test data scatter issue, probabilistic models were introduced. All ligament rupture and burst pressures of U-bends were bounded by 90% lower limits of the probabilistic models for straight tubes. It was concluded that the prediction models for straight tubes could be applied to U-bends to conservatively evaluate the ligament rupture and burst pressures of U-bends with axial flaws.

Ligament rupture and unstable burst behaviors of axial flaws in steam generator U-bends

International Nuclear Information System (INIS)

Bahn, Chi Bum; Oh, Young-Jin; Majumdar, Saurin

2015-01-01

Highlights: • Ligament rupture and unstable burst pressure tests were conducted with U-bends. • In general, U-bends showed higher ligament rupture and burst pressures than straight tubes. • U-bend test data was bounded by 90% lower limit of the probabilistic models for straight tubes. • Prediction models for straight tubes could be conservatively applied to U-bends. - Abstract: Incidents of U-bend cracking in steam generator (SG) tubes have been reported, some of which have led to tube rupture. Experimental and analytical modeling efforts to determine the failure criteria of flawed SG U-bends are limited. To evaluate structural integrity of flawed U-bends, ligament rupture and unstable burst pressure tests were conducted on 57 and 152 mm bend radius U-bends with axial electrical discharge machining notches. In general, the ligament rupture and burst pressures of the U-bends were higher than those of straight tubes with similar notches. To quantitatively address the test data scatter issue, probabilistic models were introduced. All ligament rupture and burst pressures of U-bends were bounded by 90% lower limits of the probabilistic models for straight tubes. It was concluded that the prediction models for straight tubes could be applied to U-bends to conservatively evaluate the ligament rupture and burst pressures of U-bends with axial flaws.

Cryptography for Big Data Security

Science.gov (United States)

2015-07-13

Cryptography for Big Data Security Book Chapter for Big Data: Storage, Sharing, and Security (3S) Distribution A: Public Release Ariel Hamlin1 Nabil...Email: arkady@ll.mit.edu ii Contents 1 Cryptography for Big Data Security 1 1.1 Introduction...48 Chapter 1 Cryptography for Big Data Security 1.1 Introduction With the amount

Data: Big and Small.

Science.gov (United States)

Jones-Schenk, Jan

2017-02-01

Big data is a big topic in all leadership circles. Leaders in professional development must develop an understanding of what data are available across the organization that can inform effective planning for forecasting. Collaborating with others to integrate data sets can increase the power of prediction. Big data alone is insufficient to make big decisions. Leaders must find ways to access small data and triangulate multiple types of data to ensure the best decision making. J Contin Educ Nurs. 2017;48(2):60-61. Copyright 2017, SLACK Incorporated.

The effect of cracks on the limit load of pipe bends under in-plane bending

International Nuclear Information System (INIS)

Griffiths, J.E.

1976-06-01

The limit analysis of the in-plane bending of curved tubes had received attention previously, but the effect of defects in the tube has not been considered. A lower bound has been established which, with no defects present, is in agreement with previous theoretical work. The method of linear programming allows cracks to be introduced into analysis, and results have been obtained for various geometries of defect. The results show that the presence of cracks in the pipe bend can have a marked effect on the theoretical limit load: a part-through crack penetrating only half the wall thickness will reduce the limit moment by up to 10%. The worst possible case of a through-crack may reduce the limit load by 60%. (author)

The effect of cracks on the limit load of pipe bends under in-plane bending

International Nuclear Information System (INIS)

Griffiths, J.E.

1976-06-01

The limit analysis of the in-plane bending of curved tubes had received attention previously, but the effect of defects in the tube has not been considered. A lower bound is established, which, with no defects present, is in agreement with previous theoretical work. The method of linear programming allows cracks to be introduced into the analysis. and results have been obtained for various geometries of defect. The results show that the presence of cracks in the pipe bend can have a marked effect on the theoretical limit load: a part-through crack penetrating only half the wall thickness will reduce the limit moment by up to 10%. The worst possible case of a through-crack may reduce the limit load by 60% (author)

Big Data Revisited

DEFF Research Database (Denmark)

Kallinikos, Jannis; Constantiou, Ioanna

2015-01-01

We elaborate on key issues of our paper New games, new rules: big data and the changing context of strategy as a means of addressing some of the concerns raised by the paper’s commentators. We initially deal with the issue of social data and the role it plays in the current data revolution...... and the technological recording of facts. We further discuss the significance of the very mechanisms by which big data is produced as distinct from the very attributes of big data, often discussed in the literature. In the final section of the paper, we qualify the alleged importance of algorithms and claim...... that the structures of data capture and the architectures in which data generation is embedded are fundamental to the phenomenon of big data....

Big Data in industry

Science.gov (United States)

Latinović, T. S.; Preradović, D. M.; Barz, C. R.; Latinović, M. T.; Petrica, P. P.; Pop-Vadean, A.

2016-08-01

The amount of data at the global level has grown exponentially. Along with this phenomena, we have a need for a new unit of measure like exabyte, zettabyte, and yottabyte as the last unit measures the amount of data. The growth of data gives a situation where the classic systems for the collection, storage, processing, and visualization of data losing the battle with a large amount, speed, and variety of data that is generated continuously. Many of data that is created by the Internet of Things, IoT (cameras, satellites, cars, GPS navigation, etc.). It is our challenge to come up with new technologies and tools for the management and exploitation of these large amounts of data. Big Data is a hot topic in recent years in IT circles. However, Big Data is recognized in the business world, and increasingly in the public administration. This paper proposes an ontology of big data analytics and examines how to enhance business intelligence through big data analytics as a service by presenting a big data analytics services-oriented architecture. This paper also discusses the interrelationship between business intelligence and big data analytics. The proposed approach in this paper might facilitate the research and development of business analytics, big data analytics, and business intelligence as well as intelligent agents.

Big Data Analytics An Overview

Directory of Open Access Journals (Sweden)

Jayshree Dwivedi

2015-08-01

Full Text Available Big data is a data beyond the storage capacity and beyond the processing power is called big data. Big data term is used for data sets its so large or complex that traditional data it involves data sets with sizes. Big data size is a constantly moving target year by year ranging from a few dozen terabytes to many petabytes of data means like social networking sites the amount of data produced by people is growing rapidly every year. Big data is not only a data rather it become a complete subject which includes various tools techniques and framework. It defines the epidemic possibility and evolvement of data both structured and unstructured. Big data is a set of techniques and technologies that require new forms of assimilate to uncover large hidden values from large datasets that are diverse complex and of a massive scale. It is difficult to work with using most relational database management systems and desktop statistics and visualization packages exacting preferably massively parallel software running on tens hundreds or even thousands of servers. Big data environment is used to grab organize and resolve the various types of data. In this paper we describe applications problems and tools of big data and gives overview of big data.

A peek into the future of radiology using big data applications

Directory of Open Access Journals (Sweden)

Amit T Kharat

2017-01-01

Full Text Available Big data is extremely large amount of data which is available in the radiology department. Big data is identified by four Vs – Volume, Velocity, Variety, and Veracity. By applying different algorithmic tools and converting raw data to transformed data in such large datasets, there is a possibility of understanding and using radiology data for gaining new knowledge and insights. Big data analytics consists of 6Cs – Connection, Cloud, Cyber, Content, Community, and Customization. The global technological prowess and per-capita capacity to save digital information has roughly doubled every 40 months since the 1980's. By using big data, the planning and implementation of radiological procedures in radiology departments can be given a great boost. Potential applications of big data in the future are scheduling of scans, creating patient-specific personalized scanning protocols, radiologist decision support, emergency reporting, virtual quality assurance for the radiologist, etc. Targeted use of big data applications can be done for images by supporting the analytic process. Screening software tools designed on big data can be used to highlight a region of interest, such as subtle changes in parenchymal density, solitary pulmonary nodule, or focal hepatic lesions, by plotting its multidimensional anatomy. Following this, we can run more complex applications such as three-dimensional multi planar reconstructions (MPR, volumetric rendering (VR, and curved planar reconstruction, which consume higher system resources on targeted data subsets rather than querying the complete cross-sectional imaging dataset. This pre-emptive selection of dataset can substantially reduce the system requirements such as system memory, server load and provide prompt results. However, a word of caution, “big data should not become “dump data” due to inadequate and poor analysis and non-structured improperly stored data. In the near future, big data can ring in the

A peek into the future of radiology using big data applications.

Science.gov (United States)

Kharat, Amit T; Singhal, Shubham

2017-01-01

Big data is extremely large amount of data which is available in the radiology department. Big data is identified by four Vs - Volume, Velocity, Variety, and Veracity. By applying different algorithmic tools and converting raw data to transformed data in such large datasets, there is a possibility of understanding and using radiology data for gaining new knowledge and insights. Big data analytics consists of 6Cs - Connection, Cloud, Cyber, Content, Community, and Customization. The global technological prowess and per-capita capacity to save digital information has roughly doubled every 40 months since the 1980's. By using big data, the planning and implementation of radiological procedures in radiology departments can be given a great boost. Potential applications of big data in the future are scheduling of scans, creating patient-specific personalized scanning protocols, radiologist decision support, emergency reporting, virtual quality assurance for the radiologist, etc. Targeted use of big data applications can be done for images by supporting the analytic process. Screening software tools designed on big data can be used to highlight a region of interest, such as subtle changes in parenchymal density, solitary pulmonary nodule, or focal hepatic lesions, by plotting its multidimensional anatomy. Following this, we can run more complex applications such as three-dimensional multi planar reconstructions (MPR), volumetric rendering (VR), and curved planar reconstruction, which consume higher system resources on targeted data subsets rather than querying the complete cross-sectional imaging dataset. This pre-emptive selection of dataset can substantially reduce the system requirements such as system memory, server load and provide prompt results. However, a word of caution, "big data should not become "dump data" due to inadequate and poor analysis and non-structured improperly stored data. In the near future, big data can ring in the era of personalized and

A peek into the future of radiology using big data applications

Science.gov (United States)

Kharat, Amit T.; Singhal, Shubham

2017-01-01

Big data is extremely large amount of data which is available in the radiology department. Big data is identified by four Vs – Volume, Velocity, Variety, and Veracity. By applying different algorithmic tools and converting raw data to transformed data in such large datasets, there is a possibility of understanding and using radiology data for gaining new knowledge and insights. Big data analytics consists of 6Cs – Connection, Cloud, Cyber, Content, Community, and Customization. The global technological prowess and per-capita capacity to save digital information has roughly doubled every 40 months since the 1980's. By using big data, the planning and implementation of radiological procedures in radiology departments can be given a great boost. Potential applications of big data in the future are scheduling of scans, creating patient-specific personalized scanning protocols, radiologist decision support, emergency reporting, virtual quality assurance for the radiologist, etc. Targeted use of big data applications can be done for images by supporting the analytic process. Screening software tools designed on big data can be used to highlight a region of interest, such as subtle changes in parenchymal density, solitary pulmonary nodule, or focal hepatic lesions, by plotting its multidimensional anatomy. Following this, we can run more complex applications such as three-dimensional multi planar reconstructions (MPR), volumetric rendering (VR), and curved planar reconstruction, which consume higher system resources on targeted data subsets rather than querying the complete cross-sectional imaging dataset. This pre-emptive selection of dataset can substantially reduce the system requirements such as system memory, server load and provide prompt results. However, a word of caution, “big data should not become “dump data” due to inadequate and poor analysis and non-structured improperly stored data. In the near future, big data can ring in the era of personalized

Urbanising Big

DEFF Research Database (Denmark)

Ljungwall, Christer

2013-01-01

Development in China raises the question of how big a city can become, and at the same time be sustainable, writes Christer Ljungwall of the Swedish Agency for Growth Policy Analysis.......Development in China raises the question of how big a city can become, and at the same time be sustainable, writes Christer Ljungwall of the Swedish Agency for Growth Policy Analysis....

Big bang nucleosynthesis

International Nuclear Information System (INIS)

Boyd, Richard N.

2001-01-01

The precision of measurements in modern cosmology has made huge strides in recent years, with measurements of the cosmic microwave background and the determination of the Hubble constant now rivaling the level of precision of the predictions of big bang nucleosynthesis. However, these results are not necessarily consistent with the predictions of the Standard Model of big bang nucleosynthesis. Reconciling these discrepancies may require extensions of the basic tenets of the model, and possibly of the reaction rates that determine the big bang abundances

Gender differences in variability patterns of forward bending

DEFF Research Database (Denmark)

Villumsen, Morten; Madeleine, Pascal; Jørgensen, Marie Birk

2016-01-01

The variability pattern is highly relevant in the analysis of occupational physical exposures. It is hypothesized that gender differences exist in the variability pattern of forward bending between work and leisure.......The variability pattern is highly relevant in the analysis of occupational physical exposures. It is hypothesized that gender differences exist in the variability pattern of forward bending between work and leisure....

Ductile failure of pipes with defects under combined pressure and bending

International Nuclear Information System (INIS)

Darlaston, B.J.L.; Harrison, R.P.

1977-01-01

The main part of the experimental programme was carried out on 3.5'' diam. pipes with a wall thickness of 0.064''. Various lengths of defect were assessed but only two depths, 0.044'' and 0.060''. Some full penetration defect tests were carried out under bending loading. The defects were 0.012'' wide and nominally flat bottomed. The tensile properties of the pipes were determined by taking specimens from each of the tubes. The pipes were exposed to pressure only test, bending only test and combined bending and pressure test. The results are given in tables. The observations led to the postulation of a design rule relating to the effect of defect in pipes under combined internal pressure and bending. It applies only to ductile situations in which the mode of failure is by a collapse mechanism: If the failure of a pipe containing an axial defect occurs by plastic collapse then provided the bending moment does not exceed half that for collapse due to bending alone, it will have a negligible effect on the failure pressure. (J.B.)

Reactor dosimetry calibrations in the Big Ten critical assembly

International Nuclear Information System (INIS)

Barr, D.W.; Hansen, G.E.

1977-01-01

Eleven irradiations of foil packs located in the central region of Big Ten were made for the Interlaboratory Reaction Rate Program. Each irradiation was at a nominal 10 15 fluence and the principal fluence monitor was the National Bureau of Standards' double fission chamber containing 235 U and 238 U deposits and located at the center of Big Ten. Secondary monitors consisted of three external fission chambers and two internal foil sets containing Au, In, and Al. Activities of one set were counted at the LASL and the other at the Hanford Engineering Developement Laboratory. The uncertainty in relative fluence for each irradiation was +-0.3%

The ethics of big data in big agriculture

OpenAIRE

Carbonell (Isabelle M.)

2016-01-01

This paper examines the ethics of big data in agriculture, focusing on the power asymmetry between farmers and large agribusinesses like Monsanto. Following the recent purchase of Climate Corp., Monsanto is currently the most prominent biotech agribusiness to buy into big data. With wireless sensors on tractors monitoring or dictating every decision a farmer makes, Monsanto can now aggregate large quantities of previously proprietary farming data, enabling a privileged position with unique in...

A Big Video Manifesto

DEFF Research Database (Denmark)

Mcilvenny, Paul Bruce; Davidsen, Jacob

2017-01-01

and beautiful visualisations. However, we also need to ask what the tools of big data can do both for the Humanities and for more interpretative approaches and methods. Thus, we prefer to explore how the power of computation, new sensor technologies and massive storage can also help with video-based qualitative......For the last few years, we have witnessed a hype about the potential results and insights that quantitative big data can bring to the social sciences. The wonder of big data has moved into education, traffic planning, and disease control with a promise of making things better with big numbers...

Identifying Dwarfs Workloads in Big Data Analytics

OpenAIRE

Gao, Wanling; Luo, Chunjie; Zhan, Jianfeng; Ye, Hainan; He, Xiwen; Wang, Lei; Zhu, Yuqing; Tian, Xinhui

2015-01-01

Big data benchmarking is particularly important and provides applicable yardsticks for evaluating booming big data systems. However, wide coverage and great complexity of big data computing impose big challenges on big data benchmarking. How can we construct a benchmark suite using a minimum set of units of computation to represent diversity of big data analytics workloads? Big data dwarfs are abstractions of extracting frequently appearing operations in big data computing. One dwarf represen...

Usage of information safety requirements in improving tube bending process

Science.gov (United States)

Livshitz, I. I.; Kunakov, E.; Lontsikh, P. A.

2018-05-01

This article is devoted to an improvement of the technological process's analysis with the information security requirements implementation. The aim of this research is the competition increase analysis in aircraft industry enterprises due to the information technology implementation by the example of the tube bending technological process. The article analyzes tube bending kinds and current technique. In addition, a potential risks analysis in a tube bending technological process is carried out in terms of information security.

Strength measurement of optical fibers by bending

Science.gov (United States)

Srubshchik, Leonid S.

1999-01-01

A two-point bending technique has been used not only to measure the breaking stress of optical fiber but also to predict its static and dynamic fatigue. The present theory of this test is based on elastica theory of rod. However, within the limits of elastica theory the tensile and shear stresses cannot be determined. In this paper we study dynamic and static problems for optical fiber in the two- point bending test on the base of geometrically exact theory in which rod can suffer flexure, extension, and shear. We obtain the governing partial differential equations taking into account the fact that the lateral motion of the fiber is restrained by the presence of flat parallel plates. We develop the computational methods for solving the initial and equilibrium free-boundary nonlinear planar problems. We derive the formulas for predicting of the tensile strength from strength in the bending and calculate one example.

Experimental verification of a weak zone model for timber in bending

DEFF Research Database (Denmark)

Källsner, B.; Ditlevsen, Ove Dalager; Salmela, K.

1997-01-01

In order to verify a stochastic model for the variation of bending strength within and between structural timber members, tests with long members subjected to constant bending moment have been performed. The span with constant moment contained between five and nine weak zones, i.e. zones...... with a cluster of knots. In a previous investigation test specimens, each containing one weak zone, have been tested in bending separately. Based on these tests a hierarchical model with two levels was formulated. The test results show that the bending strength of the long timber members on the average is 5...

Bends in nanotubes allow electric spin control and coupling

DEFF Research Database (Denmark)

Flensberg, Karsten; Marcus, Charles Masamed

2010-01-01

We investigate combined effects of spin-orbit coupling and magnetic field in carbon nanotubes containing one or more bends along their length. We show how bends can be used to provide electrical control of confined spins, while spins confined in straight segments remain insensitive to electric...

Applications of Big Data in Education

OpenAIRE

Faisal Kalota

2015-01-01

Big Data and analytics have gained a huge momentum in recent years. Big Data feeds into the field of Learning Analytics (LA) that may allow academic institutions to better understand the learners' needs and proactively address them. Hence, it is important to have an understanding of Big Data and its applications. The purpose of this descriptive paper is to provide an overview of Big Data, the technologies used in Big Data, and some of the applications of Big Data in educa...

Modeling and Calculation of Dent Based on Pipeline Bending Strain

Directory of Open Access Journals (Sweden)

Qingshan Feng

2016-01-01

Full Text Available The bending strain of long-distance oil and gas pipelines can be calculated by the in-line inspection tool which used inertial measurement unit (IMU. The bending strain is used to evaluate the strain and displacement of the pipeline. During the bending strain inspection, the dent existing in the pipeline can affect the bending strain data as well. This paper presents a novel method to model and calculate the pipeline dent based on the bending strain. The technique takes inertial mapping data from in-line inspection and calculates depth of dent in the pipeline using Bayesian statistical theory and neural network. To verify accuracy of the proposed method, an in-line inspection tool is used to inspect pipeline to gather data. The calculation of dent shows the method is accurate for the dent, and the mean relative error is 2.44%. The new method provides not only strain of the pipeline dent but also the depth of dent. It is more benefit for integrity management of pipeline for the safety of the pipeline.

Big Data Semantics

NARCIS (Netherlands)

Ceravolo, Paolo; Azzini, Antonia; Angelini, Marco; Catarci, Tiziana; Cudré-Mauroux, Philippe; Damiani, Ernesto; Mazak, Alexandra; van Keulen, Maurice; Jarrar, Mustafa; Santucci, Giuseppe; Sattler, Kai-Uwe; Scannapieco, Monica; Wimmer, Manuel; Wrembel, Robert; Zaraket, Fadi

2018-01-01

Big Data technology has discarded traditional data modeling approaches as no longer applicable to distributed data processing. It is, however, largely recognized that Big Data impose novel challenges in data and infrastructure management. Indeed, multiple components and procedures must be

Study of laser bending of a preloaded Titanium alloy sheet

Directory of Open Access Journals (Sweden)

Wang Xiufeng

2014-01-01

Full Text Available Laser bending of sheet metals with preload offers some attractive characteristics/merits, comparing to laser free bending without prestressing on the metals. The study reported in this paper was focused on a Titanium alloy which finds widespread applications in aerospace manufacturing. FE simulation of laser bending with prestressing on the Titanium alloy sheet was conducted for the analysis of the bending process and experiment carried out to verify the model and the result. It was shown that the simulation result is close to that measured in the experiment. Based on the computed result, the load-displacement curve was analysed and transmission efficiency of the elastic energy defined to evaluate the bending effect. These enhanced understanding of the mechanism of laser bending with a preload. A method for the optimization on technological parameters was further proposed. Referring to the deformation targeted, the preload value was determined through the FE simulation. The result showed that, on the premise that the specimen surface can be prevented from damaging, transmission efficiency of the elastic energy could reach to the maximum value through adjusting technological parameters of the laser system and deformation accuracy of the specimen could also be improved through this approach. The work presented in this paper may find its application in the manufacture of Titanium alloy sheets with a more cost-effective and a more precise way.

Tunable characteristics of bending resonance frequency in magnetoelectric laminated composites

Institute of Scientific and Technical Information of China (English)

Chen Lei; Li Ping; Wen Yu-Mei; Zhu Yong

2013-01-01

As the magnetoelectric (ME) effect in piezoelectric/magnetostrictive laminated composites is mediated by mechanical deformation,the ME effect is significantly enhanced in the vicinity of resonance frequency.The bending resonance frequency (fr) of bilayered Terfenol-D/PZT (MP) laminated composites is studied,and our analysis predicts that (i) the bending resonance frequency of an MP laminated composite can be tuned by an applied dc magnetic bias (Hdc) due to the △E effect; (ii) the bending resonance frequency of the MP laminated composite can be controlled by incorporating FeCuNbSiB layers with different thicknesses.The experimental results show that with Hdc increasing from 0Oe (1 Oe=79.5775 A/m)to 700 Oe,the bending resonance frequency can be shifted in a range of 32.68 kHz ≤ fr ≤ 33.96 kHz.In addition,with the thickness of the FeCuNbSiB layer increasing from 0 μm to 90 μm,the bending resonance frequency of the MP laminated composite gradually increases from 33.66 kHz to 39.18 kHz.This study offers a method of adjusting the strength of dc magnetic bias or the thicknesses of the FeCuNbSiB layer to tune the bending resonance frequency for ME composite,which plays a guiding role in the ME composite design for real applications.

Comparative validity of brief to medium-length Big Five and Big Six personality questionnaires

NARCIS (Netherlands)

Thalmayer, A.G.; Saucier, G.; Eigenhuis, A.

2011-01-01

A general consensus on the Big Five model of personality attributes has been highly generative for the field of personality psychology. Many important psychological and life outcome correlates with Big Five trait dimensions have been established. But researchers must choose between multiple Big Five

Quasi-static analysis and control of planer and spatial bending fluidic actuator

OpenAIRE

Chang, Benjamin Che-Ming

2011-01-01

This work presents a novel silicone-based millimetre scale bending fluidic actuator. Two designs of the bending fluidic actuator are studied: a planer actuator that bends about one axis; and a spatial actuator able to bend about two orthogonal axes. The unique parallel micro-channel design of the fluidic actuators enables operation at low working pressures, while at the same time having a very limited thickness expansion during pressurization. The fluidic actuators can be easily scaled to des...

Design and optimization of a bend-and-sweep compliant mechanism

International Nuclear Information System (INIS)

Tummala, Y; Frecker, M I; Wissa, A A; Hubbard Jr, J E

2013-01-01

A novel contact aided compliant mechanism called bend-and-sweep compliant mechanism is presented in this paper. This mechanism has nonlinear stiffness properties in two orthogonal directions. An angled compliant joint (ACJ) is the fundamental element of this mechanism. Geometric parameters of ACJs determine the stiffness of the compliant mechanism. This paper presents the design and optimization of bend-and-sweep compliant mechanism. A multi-objective optimization problem was formulated for design optimization of the bend-and-sweep compliant mechanism. The objectives of the optimization problem were to maximize or minimize the bending and sweep displacements, depending on the situation, while minimizing the von Mises stress and mass of each mechanism. This optimization problem was solved using NSGA-II (a genetic algorithm). The results of this optimization for a single ACJ during upstroke and downstroke are presented in this paper. Results of two different loading conditions used during optimization of a single ACJ for upstroke are presented. Finally, optimization results comparing the performance of compliant mechanisms with one and two ACJs are also presented. It can be inferred from these results that the number of ACJs and the design of each ACJ determines the stiffness of the bend-and-sweep compliant mechanism. These mechanisms can be used in various applications. The goal of this research is to improve the performance of ornithopters by passively morphing their wings. In order to achieve a bio-inspired wing gait called continuous vortex gait, the wings of the ornithopter need to bend, and sweep simultaneously. This can be achieved by inserting the bend-and-sweep compliant mechanism into the leading edge wing spar of the ornithopters. (paper)

Numerical method for the prediction of bending properties of glass-epoxy composites

Directory of Open Access Journals (Sweden)

Stamenović Marina R.

2007-01-01

Full Text Available Mechanical properties of composite materials are conditioned by their structure and depend on the characteristics of structural components. In this paper is presented a numerical model by which the bending properties can be predicted on the basis of known mechanical properties of tension and pressure. Determining the relationship between these properties is justified having in mind the mechanics of fracture during bending, where the fracture takes place on the outer layer which is subjected to bending while the break ends on the layer subjected to pressure. The paper gives the values of tension, pressure and bending properties obtained by the corresponding mechanical test. A comparison of the numerical results of bending properties obtained on the basis of the model with the experimental ones, shows their satisfactory agreement. Therefore, this model can be used for some future research to predict bending properties without experiments.

System effects influencing the bending strength of timber beams

DEFF Research Database (Denmark)

Ditlevsen, Ove Dalager; Källsner, B.

1998-01-01

A stochastic model of hierarchical series system type for the bending strength of spruce beams isdefined from the anticipation that the bending failure takes place at a cross-section with a defect cluster formed by knots or grain irregularities. The parameters of the model are estimated from meas...

Baryon symmetric big bang cosmology

Science.gov (United States)

Stecker, F. W.

1978-01-01

Both the quantum theory and Einsteins theory of special relativity lead to the supposition that matter and antimatter were produced in equal quantities during the big bang. It is noted that local matter/antimatter asymmetries may be reconciled with universal symmetry by assuming (1) a slight imbalance of matter over antimatter in the early universe, annihilation, and a subsequent remainder of matter; (2) localized regions of excess for one or the other type of matter as an initial condition; and (3) an extremely dense, high temperature state with zero net baryon number; i.e., matter/antimatter symmetry. Attention is given to the third assumption, which is the simplest and the most in keeping with current knowledge of the cosmos, especially as pertains the universality of 3 K background radiation. Mechanisms of galaxy formation are discussed, whereby matter and antimatter might have collided and annihilated each other, or have coexisted (and continue to coexist) at vast distances. It is pointed out that baryon symmetric big bang cosmology could probably be proved if an antinucleus could be detected in cosmic radiation.

Curvature-Induced Bunch Self-Interaction for an Energy-Chirped Bunch in Magnetic Bends

International Nuclear Information System (INIS)

Rui Li

2008-01-01

Within the realm of classical electrodynamics, the curvature-induced bunch collective interaction in magnetic bends can be studied using effective forces in the canonical formulation of the coherent synchrotron radiation (CSR) effect. As an application of this canonical formulation, in this paper, for an electron distribution moving ultrarelativistically in a bending system, the dynamics of the particles in the distribution is derived from the Hamiltonian of the particles in terms of the bunch internal coordinates. The consequent Vlasov equation manifests explicitly how the phase-space distribution is perturbed by the effective CSR forces. In particular, we study the impact of an initial linear energy chirp of the bunch on the behavior of the effective longitudinal CSR force, which arises due to the modification of the retardation relation as a result of the energy-chirping-induced longitudinal-horizontal correlation of the bunch distribution (bunch tilt) in dispersive regions. Our study demonstrates clearly the time delay (or retardation) of the behavior of the effective longitudinal CSR force on a bunch in responding to the change of the bunch length in a magnetic bend. Our result also shows that the effective longitudinal CSR force for a bunch under full compression can have sensitive dependence on the transverse position of the test particle in the bunch for certain parameter regimes

Localized bending fatigue behavior of high-strength steel monostrands

DEFF Research Database (Denmark)

Winkler, Jan; Fischer, Gregor; Georgakis, Christos T.

2012-01-01

In this paper, the localized bending fatigue behavior of pretensioned high strength steel monostrands is investigated. Furthermore, a new methodology using an optical photogrammetry system, which can quantify surface deformations on the strand is presented. The system allows measurement of the st......In this paper, the localized bending fatigue behavior of pretensioned high strength steel monostrands is investigated. Furthermore, a new methodology using an optical photogrammetry system, which can quantify surface deformations on the strand is presented. The system allows measurement...... displacement (opening/closing and sliding) of the helically wound wires. Moreover, the results are a step towards understanding the bending fatigue damage mechanisms of monostrand cables....

Different coordination and flexibility of the spine and pelvis during lateral bending between young and older adults.

Science.gov (United States)

Sung, Paul S

2016-04-01

This study examined coordination of the spine and pelvis during lateral bending of the trunk in older adults. Thirty-four healthy subjects (17 young and 17 older adults) demonstrated lateral bending at a controlled speed while holding a bar at approximately 180 degrees of shoulder flexion. Kinematic data collection was completed on the thoracic spine, lumbar spine, and pelvis. The coupling angle was calculated to examine the thorax-lumbar, lumbar-pelvis, and thorax-pelvis coordination patterns. The older adults demonstrated a reduced range of motion (ROM) of the lumbar spine, while both groups revealed similar ROM in the thorax and in the pelvis. The coupling angle between the straightening and bending phases was different only for the older adults in the thorax-lumbar (23.4±8.0 vs. -1.6±4.4, p=0.004) and the lumbar-pelvis (65.4±7.2 vs. 86.1±7.8, p=0.001) coordination. However, there was no group difference in the thorax-pelvis coordination. These findings indicate that age-related changes in the lumbar region affect coordination patterns only during the bending phase. The older adults preserved a similar pattern of movement to the young adults during the straightening phase, but the coordination variability of the coupling angles was greater for the older adults than for the young adults. This movement pattern suggests that the older adults lacked consistent trunk control in an attempt to optimize lateral bending coordination. Copyright © 2016 Elsevier B.V. All rights reserved.

Big data need big theory too.

Science.gov (United States)

Coveney, Peter V; Dougherty, Edward R; Highfield, Roger R

2016-11-13

The current interest in big data, machine learning and data analytics has generated the widespread impression that such methods are capable of solving most problems without the need for conventional scientific methods of inquiry. Interest in these methods is intensifying, accelerated by the ease with which digitized data can be acquired in virtually all fields of endeavour, from science, healthcare and cybersecurity to economics, social sciences and the humanities. In multiscale modelling, machine learning appears to provide a shortcut to reveal correlations of arbitrary complexity between processes at the atomic, molecular, meso- and macroscales. Here, we point out the weaknesses of pure big data approaches with particular focus on biology and medicine, which fail to provide conceptual accounts for the processes to which they are applied. No matter their 'depth' and the sophistication of data-driven methods, such as artificial neural nets, in the end they merely fit curves to existing data. Not only do these methods invariably require far larger quantities of data than anticipated by big data aficionados in order to produce statistically reliable results, but they can also fail in circumstances beyond the range of the data used to train them because they are not designed to model the structural characteristics of the underlying system. We argue that it is vital to use theory as a guide to experimental design for maximal efficiency of data collection and to produce reliable predictive models and conceptual knowledge. Rather than continuing to fund, pursue and promote 'blind' big data projects with massive budgets, we call for more funding to be allocated to the elucidation of the multiscale and stochastic processes controlling the behaviour of complex systems, including those of life, medicine and healthcare.This article is part of the themed issue 'Multiscale modelling at the physics-chemistry-biology interface'. © 2015 The Authors.

Bending Characteristics of Foldable Touch Display Panel with a Protection Structure Design

Directory of Open Access Journals (Sweden)

Hsien-Chie Cheng

2015-01-01

Full Text Available The study proposes and demonstrates an enhancement of a touch display panel (TDP through a polymer-based protection structure to achieve higher bendability and reliability. The bending performance of the TDP without or with the protection structure designs is addressed using three-dimensional geometry-nonlinear finite element analysis and mechanical testing. The elastic properties of the components in the TDP structure are derived from nanoindentation and uniaxial tensile/compressive testing. The calculated results are compared with each other and also against the experimental bending fatigue test data. At last, a design guideline and optimal factor setting for enhanced bending performance are sought through parametric FE analysis and Taguchi experimental design, respectively. The optimal design is compared with the original in terms of bending stress. The simulation results show that bending would create significant tensile and compressive bending stresses on the indium tin oxide/dielectric layers, which are the main cause of several commonly observed failures, such as thin film cracking and delamination, in a thin rigid film coating on a thick compliant substrate. It also turns out that a substrate with a lower stiffness has a better mechanical stability against bending stress.

Innovating Big Data Computing Geoprocessing for Analysis of Engineered-Natural Systems

Science.gov (United States)

Rose, K.; Baker, V.; Bauer, J. R.; Vasylkivska, V.

2016-12-01

Big data computing and analytical techniques offer opportunities to improve predictions about subsurface systems while quantifying and characterizing associated uncertainties from these analyses. Spatial analysis, big data and otherwise, of subsurface natural and engineered systems are based on variable resolution, discontinuous, and often point-driven data to represent continuous phenomena. We will present examples from two spatio-temporal methods that have been adapted for use with big datasets and big data geo-processing capabilities. The first approach uses regional earthquake data to evaluate spatio-temporal trends associated with natural and induced seismicity. The second algorithm, the Variable Grid Method (VGM), is a flexible approach that presents spatial trends and patterns, such as those resulting from interpolation methods, while simultaneously visualizing and quantifying uncertainty in the underlying spatial datasets. In this presentation we will show how we are utilizing Hadoop to store and perform spatial analyses to efficiently consume and utilize large geospatial data in these custom analytical algorithms through the development of custom Spark and MapReduce applications that incorporate ESRI Hadoop libraries. The team will present custom `Big Data' geospatial applications that run on the Hadoop cluster and integrate with ESRI ArcMap with the team's probabilistic VGM approach. The VGM-Hadoop tool has been specially built as a multi-step MapReduce application running on the Hadoop cluster for the purpose of data reduction. This reduction is accomplished by generating multi-resolution, non-overlapping, attributed topology that is then further processed using ESRI's geostatistical analyst to convey a probabilistic model of a chosen study region. Finally, we will share our approach for implementation of data reduction and topology generation via custom multi-step Hadoop applications, performance benchmarking comparisons, and Hadoop

Big Data and medicine: a big deal?

Science.gov (United States)

Mayer-Schönberger, V; Ingelsson, E

2018-05-01

Big Data promises huge benefits for medical research. Looking beyond superficial increases in the amount of data collected, we identify three key areas where Big Data differs from conventional analyses of data samples: (i) data are captured more comprehensively relative to the phenomenon under study; this reduces some bias but surfaces important trade-offs, such as between data quantity and data quality; (ii) data are often analysed using machine learning tools, such as neural networks rather than conventional statistical methods resulting in systems that over time capture insights implicit in data, but remain black boxes, rarely revealing causal connections; and (iii) the purpose of the analyses of data is no longer simply answering existing questions, but hinting at novel ones and generating promising new hypotheses. As a consequence, when performed right, Big Data analyses can accelerate research. Because Big Data approaches differ so fundamentally from small data ones, research structures, processes and mindsets need to adjust. The latent value of data is being reaped through repeated reuse of data, which runs counter to existing practices not only regarding data privacy, but data management more generally. Consequently, we suggest a number of adjustments such as boards reviewing responsible data use, and incentives to facilitate comprehensive data sharing. As data's role changes to a resource of insight, we also need to acknowledge the importance of collecting and making data available as a crucial part of our research endeavours, and reassess our formal processes from career advancement to treatment approval. © 2017 The Association for the Publication of the Journal of Internal Medicine.

Assessing Big Data

DEFF Research Database (Denmark)

Leimbach, Timo; Bachlechner, Daniel

2015-01-01

In recent years, big data has been one of the most controversially discussed technologies in terms of its possible positive and negative impact. Therefore, the need for technology assessments is obvious. This paper first provides, based on the results of a technology assessment study, an overview...... of the potential and challenges associated with big data and then describes the problems experienced during the study as well as methods found helpful to address them. The paper concludes with reflections on how the insights from the technology assessment study may have an impact on the future governance of big...... data....

Big data, big responsibilities

Directory of Open Access Journals (Sweden)

Primavera De Filippi

2014-01-01

Full Text Available Big data refers to the collection and aggregation of large quantities of data produced by and about people, things or the interactions between them. With the advent of cloud computing, specialised data centres with powerful computational hardware and software resources can be used for processing and analysing a humongous amount of aggregated data coming from a variety of different sources. The analysis of such data is all the more valuable to the extent that it allows for specific patterns to be found and new correlations to be made between different datasets, so as to eventually deduce or infer new information, as well as to potentially predict behaviours or assess the likelihood for a certain event to occur. This article will focus specifically on the legal and moral obligations of online operators collecting and processing large amounts of data, to investigate the potential implications of big data analysis on the privacy of individual users and on society as a whole.

Comparative validity of brief to medium-length Big Five and Big Six Personality Questionnaires.

Science.gov (United States)

Thalmayer, Amber Gayle; Saucier, Gerard; Eigenhuis, Annemarie

2011-12-01

A general consensus on the Big Five model of personality attributes has been highly generative for the field of personality psychology. Many important psychological and life outcome correlates with Big Five trait dimensions have been established. But researchers must choose between multiple Big Five inventories when conducting a study and are faced with a variety of options as to inventory length. Furthermore, a 6-factor model has been proposed to extend and update the Big Five model, in part by adding a dimension of Honesty/Humility or Honesty/Propriety. In this study, 3 popular brief to medium-length Big Five measures (NEO Five Factor Inventory, Big Five Inventory [BFI], and International Personality Item Pool), and 3 six-factor measures (HEXACO Personality Inventory, Questionnaire Big Six Scales, and a 6-factor version of the BFI) were placed in competition to best predict important student life outcomes. The effect of test length was investigated by comparing brief versions of most measures (subsets of items) with original versions. Personality questionnaires were administered to undergraduate students (N = 227). Participants' college transcripts and student conduct records were obtained 6-9 months after data was collected. Six-factor inventories demonstrated better predictive ability for life outcomes than did some Big Five inventories. Additional behavioral observations made on participants, including their Facebook profiles and cell-phone text usage, were predicted similarly by Big Five and 6-factor measures. A brief version of the BFI performed surprisingly well; across inventory platforms, increasing test length had little effect on predictive validity. Comparative validity of the models and measures in terms of outcome prediction and parsimony is discussed.

Big Machines and Big Science: 80 Years of Accelerators at Stanford

Energy Technology Data Exchange (ETDEWEB)

Loew, Gregory

2008-12-16

Longtime SLAC physicist Greg Loew will present a trip through SLAC's origins, highlighting its scientific achievements, and provide a glimpse of the lab's future in 'Big Machines and Big Science: 80 Years of Accelerators at Stanford.'

Dual of big bang and big crunch

International Nuclear Information System (INIS)

Bak, Dongsu

2007-01-01

Starting from the Janus solution and its gauge theory dual, we obtain the dual gauge theory description of the cosmological solution by the procedure of double analytic continuation. The coupling is driven either to zero or to infinity at the big-bang and big-crunch singularities, which are shown to be related by the S-duality symmetry. In the dual Yang-Mills theory description, these are nonsingular as the coupling goes to zero in the N=4 super Yang-Mills theory. The cosmological singularities simply signal the failure of the supergravity description of the full type IIB superstring theory

Enhanced Transmissions Through Three-dimensional Cascade Sharp Waveguide Bends Using C-slit Diaphragms.

Science.gov (United States)

Yang, Rui; Hu, Bowei; Zhang, Aofang; Gao, Dongxing; Wang, Hui; Shi, Ayuan; Lei, Zhenya; Yang, Pei

2017-03-21

Transmission properties through sharp rectangular waveguide bends are investigated to determine the cut-off bending angles of the wave propagation. We show that a simple metallic diaphragm at the bending corner with properly devised sub-wavelength defect apertures of C-slits would be readily to turn on the transmissions with scarce reflections of the propagating modes, while preserving the integrity of the transmitting fields soon after the bends. In particularly, our design also demonstrates the capability of eliminating all the unwanted cavity resonant transmissions that exist in the three-dimensional cascade sharp waveguide bends, and solely let the desired signals travel along the whole passage of the waveguide. The present approach, using C-slit diaphragms to support the sharp bending behaviors of the guided waves with greatly enhanced transmissions, would be especially effective in constructing novel waveguides and pave the way for the development of more compact and miniaturized electromagnetic systems that exploit these waveguide bends.

Comparative Validity of Brief to Medium-Length Big Five and Big Six Personality Questionnaires

Science.gov (United States)

Thalmayer, Amber Gayle; Saucier, Gerard; Eigenhuis, Annemarie

2011-01-01

A general consensus on the Big Five model of personality attributes has been highly generative for the field of personality psychology. Many important psychological and life outcome correlates with Big Five trait dimensions have been established. But researchers must choose between multiple Big Five inventories when conducting a study and are…

Interaction region

International Nuclear Information System (INIS)

Anon.

1982-01-01

The Interaction Region Group addressed the basic questions of how to collide the SLC beams, how to maximize and monitor the luminosity, and how to minimize the detector backgrounds at the interaction region. In practice, five subgroups evolved to study these questions. The final focus group provided three alternative designs to acheive the 1 to 2 micron beam spot size required by the SLC, as well as studying other problems including: eta, eta' matching from the collider arcs, the implementation of soft bends near the interaction region, beam emittance growth, and magnet tolerances in the final focus. The beam position monitor group proposed two devices, a strip line monitor, and a beamstrahlung monitor, to bring the beams into collision. The luminosity monitor group reviewed the possible QED processes that would be insensitive to weak interaction (Z 0 ) effects. The beam dumping group proposed locations for kicker and septum magnets in the final focus that would achieve a high dumping efficiency and would meet the desired beam tolerances at the Moller scattering target in the beam dump line. Working with the Polarization Group, the Moller experiment was designed into the beam dump beam line. A beam dump was proposed that would maintain radiation backgrounds (penetrating muons) at acceptible levels. The detector backgrounds group proposed soft-bend and masking configurations to shield the detector from synchrotron radiation from the hard/soft bends and from the final focus quadrupoles and evaluated the effectiveness of these designs for the three final focus optics designs. Backgrounds were also estimated from: large angle synchrotron radiation, local and distant beam-gas interactions, 2-photon interactions, and from neutrons and backscattered photons from the beamstrahlung dump

Big data for health.

Science.gov (United States)

Andreu-Perez, Javier; Poon, Carmen C Y; Merrifield, Robert D; Wong, Stephen T C; Yang, Guang-Zhong

2015-07-01

This paper provides an overview of recent developments in big data in the context of biomedical and health informatics. It outlines the key characteristics of big data and how medical and health informatics, translational bioinformatics, sensor informatics, and imaging informatics will benefit from an integrated approach of piecing together different aspects of personalized information from a diverse range of data sources, both structured and unstructured, covering genomics, proteomics, metabolomics, as well as imaging, clinical diagnosis, and long-term continuous physiological sensing of an individual. It is expected that recent advances in big data will expand our knowledge for testing new hypotheses about disease management from diagnosis to prevention to personalized treatment. The rise of big data, however, also raises challenges in terms of privacy, security, data ownership, data stewardship, and governance. This paper discusses some of the existing activities and future opportunities related to big data for health, outlining some of the key underlying issues that need to be tackled.

Species delimitation and morphological divergence in the scorpion Centruroides vittatus (Say, 1821: insights from phylogeography.

Directory of Open Access Journals (Sweden)

Tsunemi Yamashita

Full Text Available Scorpion systematics and taxonomy have recently shown a need for revision, partially due to insights from molecular techniques. Scorpion taxonomy has been difficult with morphological characters as disagreement exists among researchers with character choice for adequate species delimitation in taxonomic studies. Within the family Buthidae, species identification and delimitation is particularly difficult due to the morphological similarity among species and extensive intraspecific morphological diversity. The genus Centruroides in the western hemisphere is a prime example of the difficulty in untangling the taxonomic complexity within buthid scorpions. In this paper, we present phylogeographic, Ecological Niche Modeling, and morphometric analyses to further understand how population diversification may have produced morphological diversity in Centruroides vittatus (Say, 1821. We show that C. vittatus populations in the Big Bend and Trans-Pecos region of Texas, USA are phylogeographically distinct and may predate the Last Glacial Maximum (LGM. In addition, we suggest the extended isolation of Big Bend region populations may have created the C. vittatus variant once known as C. pantheriensis.

Slice through an LHC bending magnet

CERN Multimedia

Slice through an LHC superconducting dipole (bending) magnet. The slice includes a cut through the magnet wiring (niobium titanium), the beampipe and the steel magnet yokes. Particle beams in the Large Hadron Collider (LHC) have the same energy as a high-speed train, squeezed ready for collision into a space narrower than a human hair. Huge forces are needed to control them. Dipole magnets (2 poles) are used to bend the paths of the protons around the 27 km ring. Quadrupole magnets (4 poles) focus the proton beams and squeeze them so that more particles collide when the beams’ paths cross. There are 1232 15m long dipole magnets in the LHC.

Holey fibers for low bend loss

Science.gov (United States)

Nakajima, Kazuhide; Saito, Kotaro; Yamada, Yusuke; Kurokawa, Kenji; Shimizu, Tomoya; Fukai, Chisato; Matsui, Takashi

2013-12-01

Bending-loss insensitive fiber (BIF) has proved an essential medium for constructing the current fiber to the home (FTTH) network. By contrast, the progress that has been made on holey fiber (HF) technologies provides us with novel possibilities including non-telecom applications. In this paper, we review recent progress on hole-assisted type BIF. A simple design consideration is overviewed. We then describe some of the properties of HAF including its mechanical reliability. Finally, we introduce some applications of HAF including to high power transmission. We show that HAF with a low bending loss has the potential for use in various future optical technologies as well as in the optical communication network.

Big defensins, a diverse family of antimicrobial peptides that follows different patterns of expression in hemocytes of the oyster Crassostrea gigas.

Science.gov (United States)

Rosa, Rafael D; Santini, Adrien; Fievet, Julie; Bulet, Philippe; Destoumieux-Garzón, Delphine; Bachère, Evelyne

2011-01-01

Big defensin is an antimicrobial peptide composed of a highly hydrophobic N-terminal region and a cationic C-terminal region containing six cysteine residues involved in three internal disulfide bridges. While big defensin sequences have been reported in various mollusk species, few studies have been devoted to their sequence diversity, gene organization and their expression in response to microbial infections. Using the high-throughput Digital Gene Expression approach, we have identified in Crassostrea gigas oysters several sequences coding for big defensins induced in response to a Vibrio infection. We showed that the oyster big defensin family is composed of three members (named Cg-BigDef1, Cg-BigDef2 and Cg-BigDef3) that are encoded by distinct genomic sequences. All Cg-BigDefs contain a hydrophobic N-terminal domain and a cationic C-terminal domain that resembles vertebrate β-defensins. Both domains are encoded by separate exons. We found that big defensins form a group predominantly present in mollusks and closer to vertebrate defensins than to invertebrate and fungi CSαβ-containing defensins. Moreover, we showed that Cg-BigDefs are expressed in oyster hemocytes only and follow different patterns of gene expression. While Cg-BigDef3 is non-regulated, both Cg-BigDef1 and Cg-BigDef2 transcripts are strongly induced in response to bacterial challenge. Induction was dependent on pathogen associated molecular patterns but not damage-dependent. The inducibility of Cg-BigDef1 was confirmed by HPLC and mass spectrometry, since ions with a molecular mass compatible with mature Cg-BigDef1 (10.7 kDa) were present in immune-challenged oysters only. From our biochemical data, native Cg-BigDef1 would result from the elimination of a prepropeptide sequence and the cyclization of the resulting N-terminal glutamine residue into a pyroglutamic acid. We provide here the first report showing that big defensins form a family of antimicrobial peptides diverse not only in terms

Bending Moment Calculations for Piles Based on the Finite Element Method

Directory of Open Access Journals (Sweden)

Yu-xin Jie

2013-01-01

Full Text Available Using the finite element analysis program ABAQUS, a series of calculations on a cantilever beam, pile, and sheet pile wall were made to investigate the bending moment computational methods. The analyses demonstrated that the shear locking is not significant for the passive pile embedded in soil. Therefore, higher-order elements are not always necessary in the computation. The number of grids across the pile section is important for bending moment calculated with stress and less significant for that calculated with displacement. Although computing bending moment with displacement requires fewer grid numbers across the pile section, it sometimes results in variation of the results. For displacement calculation, a pile row can be suitably represented by an equivalent sheet pile wall, whereas the resulting bending moments may be different. Calculated results of bending moment may differ greatly with different grid partitions and computational methods. Therefore, a comparison of results is necessary when performing the analysis.

In situ transmission electron microscopy of individual carbon nanotetrahedron/ribbon structures in bending

Energy Technology Data Exchange (ETDEWEB)

Kohno, Hideo, E-mail: kohno.hideo@kochi-tech.ac.jp [School of Environmental Science and Engineering, Kochi University of Technology, Kami, Kochi 782-8502 (Japan); Masuda, Yusuke [Graduate School of Science, Osaka University, Toyonaka, Osaka 560-0043 (Japan)

2015-05-11

When the direction of flattening of a carbon nanotube changes during growth mediated by a metal nanoparticle, a carbon nanotetrahedron is formed in the middle of the carbon nanoribbon. We report the bending properties of the carbon nanotetrahedron/nanoribbon structure using a micro-manipulator system in a transmission electron microscope. In many cases, bending occurs at an edge of the carbon nanotetrahedron. No significant change is observed in the tetrahedron's shape during bending, and the bending is reversible and repeatable. Our results show that the carbon nanotetrahedron/nanoribbon structure has good durability against mechanical bending.

Features of the magnetic field of a rectangular combined function bending magnet

International Nuclear Information System (INIS)

Hwang, C.S.; National Chiao Tung Univ., Hsinchu; Chang, C.H.; Hwang, G.J.; Uen, T.M.; Tseng, P.K.; National Taiwan Univ., Taipei

1996-01-01

Magnetic field features of the combined function bending magnet with dipole and quadrupole field components are essential for the successful operation of the electron beam trajectory. These fields also dominate the photon beam quality. The vertical magnetic field B y (x,y) calculation is performed by a computer code MAGNET at the magnet center (s = 0). Those results are compared with the 2-D field measurement by the Hall probe mapping system. Also detailed survey has been made of the harmonic field strength and the main features of the fundamental integrated strength, effective length, magnetic symmetry, tilt of the pole face, offset of the field center and the fringe field. The end shims that compensate for the strong end negative sextupole field to increase the good field region for the entire integrated strength are discussed. An important physical feature of this combined function bending magnet is the constant ratio of dipole and quadrupole strength ∫Bds/∫Gds which is expressed as a function of excitation current in the energy range 0.6 to 1.5 GeV

The importance of jet bending in gamma-ray AGNs—revisited

Energy Technology Data Exchange (ETDEWEB)

Graham, P. J. [School of Physics, University of New South Wales, Sydney, NSW 2052 (Australia); Tingay, S. J. [International Centre for Radio Astronomy Research, Curtin University, Bentley, WA (Australia)

2014-04-01

We investigate the hypothesis that γ-ray-quiet active galactic nuclei (AGNs) have a greater tendency for jet bending than γ-ray-loud AGNs, revisiting the analysis of Tingay et al. We perform a statistical analysis using a large sample of 351 radio-loud AGNs along with γ-ray identifications from the Fermi Large Area Telescope (LAT). Our results show no statistically significant differences in jet-bending properties between γ-ray-loud and γ-ray-quiet populations, indicating that jet bending is not a significant factor for γ-ray detection in AGNs.

Mass transfer coefficient factor in pipe bend - 3 D CFD analysis

International Nuclear Information System (INIS)

Prasad, Mahendra; Gaikwad, Avinash J.; Madasamy, P.; Krishnamohan, T.V.; Velumurugan, S.; Sridharan, Arunkumar; Parida, Smrutiranjan

2015-01-01

In power industries Flow Accelerated Corrosion (FAC) has been a concern for pipe wall thinning where high velocity fluid at elevated temperatures is used. Even straight pipes are found to have non uniform corrosion and this is enhanced in junctions such as bends, orifices etc. Mass transfer coefficient (MTC) which defines the amount of corrosion changes from its value in straight pipe (with same fluid parameters) for flow in bends, orifice etc due to changes in velocity profile in axial direction. In this paper, 3 D computational fluid dynamics (CFD) simulation is carried out for an experiment on 58° bend angle and 2D bend radius circular carbon steel pipe carrying water at 120°C under neutral pH conditions. The turbulent model K-ω with shear stress transport was used for this purpose. The mass transfer boundary layer (MTBL) thickness δ mtbl depends on Schmidt number (Sc), as δ mtbl ∼ δ h /(Sc 1/3 ). MTBL is significantly smaller than hydrodynamic boundary layer δ h for large Sc, hence boundary layer meshing was carried out deep into δ mtbl . Uniform velocity was applied at the inlet. The flow velocity was 3 m/s at room temperature while the experimental fluid velocity was 7 m/s. Lower value of fluid velocity is chosen due to the limitations of grid size since it depends inversely on fluid velocity. The ratio of MTC in bend to straight pipe is not strongly dependent on Sc. CFD simulation at lower temperature is sufficient to get approximate MTC in bends. The ratio of the mass transfer coefficient at some locations in bend to the straight pipe coefficient (MTCR) is determined through simulation. The MTC increased in the extrados of the bend towards the outlet. (author)

Inhomogeneous Big Bang Nucleosynthesis Revisited

OpenAIRE

Lara, J. F.; Kajino, T.; Mathews, G. J.

2006-01-01

We reanalyze the allowed parameters for inhomogeneous big bang nucleosynthesis in light of the WMAP constraints on the baryon-to-photon ratio and a recent measurement which has set the neutron lifetime to be 878.5 +/- 0.7 +/- 0.3 seconds. For a set baryon-to-photon ratio the new lifetime reduces the mass fraction of He4 by 0.0015 but does not significantly change the abundances of other isotopes. This enlarges the region of concordance between He4 and deuterium in the parameter space of the b...

Design and Construction of the Plat Bending Machine

International Nuclear Information System (INIS)

Edy Sumarno; Abdul Hafid; Ismu H; Joko P W; Bambang Heru

2003-01-01

The plat-bending machine has been fabricated. The type is manual. That machine was made by plate, cylinder and U plat material. The machine has dimensions 110 mm in height, 650 mm in width, and 1200 mm in height. The capability of this machine is bending the plat with 2 mm in thickness and 1000 mm in width. This machine has the advantage to operate without electrical supply and easy to operate. (author)

Big Data: Implications for Health System Pharmacy.

Science.gov (United States)

Stokes, Laura B; Rogers, Joseph W; Hertig, John B; Weber, Robert J

2016-07-01

Big Data refers to datasets that are so large and complex that traditional methods and hardware for collecting, sharing, and analyzing them are not possible. Big Data that is accurate leads to more confident decision making, improved operational efficiency, and reduced costs. The rapid growth of health care information results in Big Data around health services, treatments, and outcomes, and Big Data can be used to analyze the benefit of health system pharmacy services. The goal of this article is to provide a perspective on how Big Data can be applied to health system pharmacy. It will define Big Data, describe the impact of Big Data on population health, review specific implications of Big Data in health system pharmacy, and describe an approach for pharmacy leaders to effectively use Big Data. A few strategies involved in managing Big Data in health system pharmacy include identifying potential opportunities for Big Data, prioritizing those opportunities, protecting privacy concerns, promoting data transparency, and communicating outcomes. As health care information expands in its content and becomes more integrated, Big Data can enhance the development of patient-centered pharmacy services.

Generalized formal model of Big Data

OpenAIRE

Shakhovska, N.; Veres, O.; Hirnyak, M.

2016-01-01

This article dwells on the basic characteristic features of the Big Data technologies. It is analyzed the existing definition of the “big data” term. The article proposes and describes the elements of the generalized formal model of big data. It is analyzed the peculiarities of the application of the proposed model components. It is described the fundamental differences between Big Data technology and business analytics. Big Data is supported by the distributed file system Google File System ...

BigWig and BigBed: enabling browsing of large distributed datasets.

Science.gov (United States)

Kent, W J; Zweig, A S; Barber, G; Hinrichs, A S; Karolchik, D

2010-09-01

BigWig and BigBed files are compressed binary indexed files containing data at several resolutions that allow the high-performance display of next-generation sequencing experiment results in the UCSC Genome Browser. The visualization is implemented using a multi-layered software approach that takes advantage of specific capabilities of web-based protocols and Linux and UNIX operating systems files, R trees and various indexing and compression tricks. As a result, only the data needed to support the current browser view is transmitted rather than the entire file, enabling fast remote access to large distributed data sets. Binaries for the BigWig and BigBed creation and parsing utilities may be downloaded at http://hgdownload.cse.ucsc.edu/admin/exe/linux.x86_64/. Source code for the creation and visualization software is freely available for non-commercial use at http://hgdownload.cse.ucsc.edu/admin/jksrc.zip, implemented in C and supported on Linux. The UCSC Genome Browser is available at http://genome.ucsc.edu.

Pipeline Bending Strain Measurement and Compensation Technology Based on Wavelet Neural Network

Directory of Open Access Journals (Sweden)

Rui Li

2016-01-01

Full Text Available The bending strain of long distance oil and gas pipelines may lead to instability of the pipeline and failure of materials, which seriously deteriorates the transportation security of oil and gas. To locate the position of the bending strain for maintenance, an Inertial Measurement Unit (IMU is usually adopted in a Pipeline Inspection Gauge (PIG. The attitude data of the IMU is usually acquired to calculate the bending strain in the pipe. However, because of the vibrations in the pipeline and other system noises, the resulting bending strain calculations may be incorrect. To improve the measurement precision, a method, based on wavelet neural network, was proposed. To test the proposed method experimentally, a PIG with the proposed method is used to detect a straight pipeline. It can be obtained that the proposed method has a better repeatability and convergence than the original method. Furthermore, the new method is more accurate than the original method and the accuracy of bending strain is raised by about 23% compared to original method. This paper provides a novel method for precisely inspecting bending strain of long distance oil and gas pipelines and lays a foundation for improving the precision of inspection of bending strain of long distance oil and gas pipelines.

Investigating Seed Longevity of Big Sagebrush (Artemisia tridentata)

Science.gov (United States)

Wijayratne, Upekala C.; Pyke, David A.

2009-01-01

The Intermountain West is dominated by big sagebrush communities (Artemisia tridentata subspecies) that provide habitat and forage for wildlife, prevent erosion, and are economically important to recreation and livestock industries. The two most prominent subspecies of big sagebrush in this region are Wyoming big sagebrush (A. t. ssp. wyomingensis) and mountain big sagebrush (A. t. ssp. vaseyana). Increased understanding of seed bank dynamics will assist with sustainable management and persistence of sagebrush communities. For example, mountain big sagebrush may be subjected to shorter fire return intervals and prescribed fire is a tool used often to rejuvenate stands and reduce tree (Juniperus sp. or Pinus sp.) encroachment into these communities. A persistent seed bank for mountain big sagebrush would be advantageous under these circumstances. Laboratory germination trials indicate that seed dormancy in big sagebrush may be habitat-specific, with collections from colder sites being more dormant. Our objective was to investigate seed longevity of both subspecies by evaluating viability of seeds in the field with a seed retrieval experiment and sampling for seeds in situ. We chose six study sites for each subspecies. These sites were dispersed across eastern Oregon, southern Idaho, northwestern Utah, and eastern Nevada. Ninety-six polyester mesh bags, each containing 100 seeds of a subspecies, were placed at each site during November 2006. Seed bags were placed in three locations: (1) at the soil surface above litter, (2) on the soil surface beneath litter, and (3) 3 cm below the soil surface to determine whether dormancy is affected by continued darkness or environmental conditions. Subsets of seeds were examined in April and November in both 2007 and 2008 to determine seed viability dynamics. Seed bank samples were taken at each site, separated into litter and soil fractions, and assessed for number of germinable seeds in a greenhouse. Community composition data

Limit load solutions for piping branch junctions under out-of-plane bending

International Nuclear Information System (INIS)

Xu, Ying Hu; Lee, Kuk Hee; Jeon, Jun Young; Kim, Yun Jae

2009-01-01

Approximate plastic limit load solutions for piping branch junctions under out-of plane bending are obtained from detailed three-dimensional (3-D) FE limit analyses based on elastic-perfectly plastic materials with the small geometry change option. Two types of bending are considered; out-of-plane bending to the branch pipe and out-of-plane bending to the run pipe. Accordingly closed-form approximations are proposed for piping branch junctions under out-of-plane bending based on the FE results. The proposed solutions are valid for the branch-to-run pipe radius and thickness from 0.0 to 1.0, and the mean radius-to-thickness ratio of the run pipe from 2.0 to 20.0. And, this study provides effects of reinforcement area on plastic limit loads.

Directly Printable Flexible Strain Sensors for Bending and Contact Feedback of Soft Actuators

Directory of Open Access Journals (Sweden)

Khaled Elgeneidy

2018-02-01

Full Text Available This paper presents a fully printable sensorized bending actuator that can be calibrated to provide reliable bending feedback and simple contact detection. A soft bending actuator following a pleated morphology, as well as a flexible resistive strain sensor, were directly 3D printed using easily accessible FDM printer hardware with a dual-extrusion tool head. The flexible sensor was directly welded to the bending actuator’s body and systematically tested to characterize and evaluate its response under variable input pressure. A signal conditioning circuit was developed to enhance the quality of the sensory feedback, and flexible conductive threads were used for wiring. The sensorized actuator’s response was then calibrated using a vision system to convert the sensory readings to real bending angle values. The empirical relationship was derived using linear regression and validated at untrained input conditions to evaluate its accuracy. Furthermore, the sensorized actuator was tested in a constrained setup that prevents bending, to evaluate the potential of using the same sensor for simple contact detection by comparing the constrained and free-bending responses at the same input pressures. The results of this work demonstrated how a dual-extrusion FDM printing process can be tuned to directly print highly customizable flexible strain sensors that were able to provide reliable bending feedback and basic contact detection. The addition of such sensing capability to bending actuators enhances their functionality and reliability for applications such as controlled soft grasping, flexible wearables, and haptic devices.

Springback Mechanism Analysis and Experiments on Robotic Bending of Rectangular Orthodontic Archwire

Science.gov (United States)

Jiang, Jin-Gang; Han, Ying-Shuai; Zhang, Yong-De; Liu, Yan-Jv; Wang, Zhao; Liu, Yi

2017-11-01

Fixed-appliance technology is the most common and effective malocclusion orthodontic treatment method, and its key step is the bending of orthodontic archwire. The springback of archwire did not consider the movement of the stress-strain-neutral layer. To solve this problem, a springback calculation model for rectangular orthodontic archwire is proposed. A bending springback experiment is conducted using an orthodontic archwire bending springback measurement device. The springback experimental results show that the theoretical calculation results using the proposed model coincide better with the experimental testing results than when movement of the stress-strain-neutral layer was not considered. A bending experiment with rectangular orthodontic archwire is conducted using a robotic orthodontic archwire bending system. The patient expriment result show that the maximum and minimum error ratios of formed orthodontic archwire parameters are 22.46% and 10.23% without considering springback and are decreased to 11.35% and 6.13% using the proposed model. The proposed springback calculation model, which considers the movement of the stress-strain-neutral layer, greatly improves the orthodontic archwire bending precision.

Low Cycle Fatigue of Steel in Strain Controled Cyclic Bending

Directory of Open Access Journals (Sweden)

Kulesa Anna

2016-03-01

Full Text Available The paper presents a comparison of the fatigue life curves based on test of 15Mo3 steel under cyclic, pendulum bending and tension-compression. These studies were analyzed in terms of a large and small number of cycles where strain amplitude is dependent on the fatigue life. It has been shown that commonly used Manson-Coffin-Basquin model cannot be used for tests under cyclic bending due to the impossibility of separating elastic and plastic strains. For this purpose, some well-known models of Langer and Kandil and one new model of authors, where strain amplitude is dependent on the number of cycles, were proposed. Comparing the results of bending with tension-compression it was shown that for smaller strain amplitudes the fatigue life for both test methods were similar, for higher strain amplitudes fatigue life for bending tests was greater than for tension-compression.

Stress Corrosion Cracking of Basalt/Epoxy Composites under Bending Loading

Science.gov (United States)

Shokrieh, Mahmood M.; Memar, Mahdi

2010-04-01

The purpose of this research is to study the stress corrosion behavior of basalt/epoxy composites under bending loading and submerged in 5% sulfuric acid corrosive medium. There are limited numbers of research in durability of fiber reinforced polymer composites. Moreover, studies on basalt fibers and its composites are very limited. In this research, mechanical property degradation of basalt/epoxy composites under bending loading and submerged in acidic corrosive medium is investigated. Three states of stress, equal to 30%, 50% and 70% of the ultimate strength of composites, are applied on samples. High stress states are applied to the samples to accelerate the testing procedure. Mechanical properties degradation consists of bending strength, bending modulus of elasticity and fracture energy of samples are examined. Also, a normalized strength degradation model for stress corrosion condition is presented. Finally, microscopic images of broken cross sections of samples are examined.

Improving formability of tube bending for a copper material using finite element simulation

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Duc Toan; Nnuyen, Dinh Thanh [Hungyen University of Technology and Education, Hungyen (Viet Nam); Kim, Young Suk [Kyungpook National University, Daegu (Korea, Republic of)

2015-10-15

Bending tubes are key products in many industries. The geometric parameters of the bending process are considered according to Taguchi's orthogonal array and then coupled with finite element simulation to predict and improve the formability of the tube bending process for copper JIS25A material. Three parameters, namely, mandrel diameter, distance between mandrel rings, and distance from the tip of the mandrel bar to the center of the base die, are selected to study their effects on the quality of the bending process. The variance analysis shows that the effect distribution of each parameter to bending quality is determined, and optimal conditions are adopted to conduct experiments.

Big data-driven business how to use big data to win customers, beat competitors, and boost profits

CERN Document Server

Glass, Russell

2014-01-01

Get the expert perspective and practical advice on big data The Big Data-Driven Business: How to Use Big Data to Win Customers, Beat Competitors, and Boost Profits makes the case that big data is for real, and more than just big hype. The book uses real-life examples-from Nate Silver to Copernicus, and Apple to Blackberry-to demonstrate how the winners of the future will use big data to seek the truth. Written by a marketing journalist and the CEO of a multi-million-dollar B2B marketing platform that reaches more than 90% of the U.S. business population, this book is a comprehens

A new insole measurement system to detect bending and torsional moments at the human foot during footwear condition: a technical report.

Science.gov (United States)

Stief, Thomas; Peikenkamp, Klaus

2015-01-01

Stress occurring at the feet while wearing footwear is often determined using pressure measurement systems. However, other forms of stress, such as bending, torsional and shear loadings, cannot be detected in shoes during day-to-day activities. Nevertheless, the detection of these types of stresses would be helpful for understanding the mechanical aspects of various kinds of hard and soft tissue injuries. Therefore, we describe the development of a new measuring device that allows the reliable determination of bending and torsional load at the foot in shoes. The system consists of a measuring insole and an analogue device with Bluetooth interface. The specific shape of the insole base layer, the positions of the strain gauges, and the interconnections between them have all been selected in such a way so as to isolate bending and torsional moment detections in the medial and lateral metatarsal region. The system was calibrated using a classical two-point test procedure. A single case study was executed to evaluate the new device for practical use. This application consisted of one subject wearing neutral shoes walking on a treadmill. The calibration results (coefficients of determination R(2) > 0.999) show that bending and torsional load can be reliably detected using the measurement system presented. In the single case study, alternating bending and torsional load can be detected during walking, and the shape of the detected bending moments can be confirmed by the measurements of Arndt et al. (J Biomech 35:621-8, 2002). Despite some limitations, the presented device allows for the reliable determination of bending and torsional stresses at the foot in shoes.

Big Game Reporting Stations

Data.gov (United States)

Vermont Center for Geographic Information — Point locations of big game reporting stations. Big game reporting stations are places where hunters can legally report harvested deer, bear, or turkey. These are...

Mathematical model of polyethylene pipe bending stress state

Science.gov (United States)

Serebrennikov, Anatoly; Serebrennikov, Daniil

2018-03-01

Introduction of new machines and new technologies of polyethylene pipeline installation is usually based on the polyethylene pipe flexibility. It is necessary that existing bending stresses do not lead to an irreversible polyethylene pipe deformation and to violation of its strength characteristics. Derivation of the mathematical model which allows calculating analytically the bending stress level of polyethylene pipes with consideration of nonlinear characteristics is presented below. All analytical calculations made with the mathematical model are experimentally proved and confirmed.

Vortex breakdown in simple pipe bends

Science.gov (United States)

Ault, Jesse; Shin, Sangwoo; Stone, Howard

2016-11-01

Pipe bends and elbows are one of the most common fluid mechanics elements that exists. However, despite their ubiquity and the extensive amount of research related to these common, simple geometries, unexpected complexities still remain. We show that for a range of geometries and flow conditions, these simple flows experience unexpected fluid dynamical bifurcations resembling the bubble-type vortex breakdown phenomenon. Specifically, we show with simulations and experiments that recirculation zones develop within the bends under certain conditions. As a consequence, fluid and particles can remain trapped within these structures for unexpectedly-long time scales. We also present simple techniques to mitigate this recirculation effect which can potentially have impact across industries ranging from biomedical and chemical processing to food and health sciences.

Effect of confinements: Bending in Paramecium

Science.gov (United States)

Eddins, Aja; Yang, Sung; Spoon, Corrie; Jung, Sunghwan

2012-02-01

Paramecium is a unicellular eukaryote which by coordinated beating of cilia, generates metachronal waves which causes it to execute a helical trajectory. We investigate the swimming parameters of the organism in rectangular PDMS channels and try to quantify its behavior. Surprisingly a swimming Paramecium in certain width of channels executes a bend of its flexible body (and changes its direction of swimming) by generating forces using the cilia. Considering a simple model of beam constrained between two walls, we predict the bent shapes of the organism and the forces it exerts on the walls. Finally we try to explain how bending (by sensing) can occur in channels by conducting experiments in thin film of fluid and drawing analogy to swimming behavior observed in different cases.

Research on taxi software policy based on big data

Directory of Open Access Journals (Sweden)

Feng Daoming

2017-01-01

Full Text Available Through big data analysis, statistical analysis of a large number of factors affect the establishment of the rally car index set, By establishing a mathematical model to analyze the different space-time taxi resource “to match supply and demand” degree, combined with intelligent deployment to solve the “taxi difficult” this hot social issues. This article takes Shanghai as an example, the central park, Lu Xun park, century park three areas as the object of study. From the “sky drops fast travel intelligence platform” big data, Extracted passenger demand and the number of taxi Kongshi data. Then demand and supply of taxis to establish indicators matrix, get the degree of matching supply needs of the region. Then through the big data relevant policies of each taxi company. Using the method of cluster analysis, to find the decisive role of the three aspects of the factors, using principal component analysis, compare the advantages and disadvantages of the existing company’s programs. Finally, according to the above research to develop a reasonable taxi software related policies.

Stalin's Big Fleet Program

National Research Council Canada - National Science Library

Mauner, Milan

2002-01-01

Although Dr. Milan Hauner's study 'Stalin's Big Fleet program' has focused primarily on the formation of Big Fleets during the Tsarist and Soviet periods of Russia's naval history, there are important lessons...

Big Data-Driven Based Real-Time Traffic Flow State Identification and Prediction

Directory of Open Access Journals (Sweden)

Hua-pu Lu

2015-01-01

Full Text Available With the rapid development of urban informatization, the era of big data is coming. To satisfy the demand of traffic congestion early warning, this paper studies the method of real-time traffic flow state identification and prediction based on big data-driven theory. Traffic big data holds several characteristics, such as temporal correlation, spatial correlation, historical correlation, and multistate. Traffic flow state quantification, the basis of traffic flow state identification, is achieved by a SAGA-FCM (simulated annealing genetic algorithm based fuzzy c-means based traffic clustering model. Considering simple calculation and predictive accuracy, a bilevel optimization model for regional traffic flow correlation analysis is established to predict traffic flow parameters based on temporal-spatial-historical correlation. A two-stage model for correction coefficients optimization is put forward to simplify the bilevel optimization model. The first stage model is built to calculate the number of temporal-spatial-historical correlation variables. The second stage model is present to calculate basic model formulation of regional traffic flow correlation. A case study based on a real-world road network in Beijing, China, is implemented to test the efficiency and applicability of the proposed modeling and computing methods.

Improving bending stress in spur gears using asymmetric gears and shape optimization

DEFF Research Database (Denmark)

Pedersen, Niels Leergaard

2010-01-01

Bending stress plays a significant role in gear design wherein its magnitude is controlled by the nominal bending stress and the stress concentration due to the geometrical shape. The bending stress is indirectly related to shape changes made to the cutting tool. This work shows that the bending...... stress can be reduced significantly by using asymmetric gear teeth and by shape optimizing the gear through changes made to the tool geometry. However, to obtain the largest possible stress reduction a custom tool must be designed depending on the number of teeth, but the stress reductions found...

Five Big, Big Five Issues : Rationale, Content, Structure, Status, and Crosscultural Assessment

NARCIS (Netherlands)

De Raad, Boele

1998-01-01

This article discusses the rationale, content, structure, status, and crosscultural assessment of the Big Five trait factors, focusing on topics of dispute and misunderstanding. Taxonomic restrictions of the original Big Five forerunner, the "Norman Five," are discussed, and criticisms regarding the

Bend-resistant large mode area fiber with novel segmented cladding

Science.gov (United States)

Ma, Shaoshuo; Ning, Tigang; Pei, Li; Li, Jing; Zheng, Jingjing

2018-01-01

A novel structure of segment cladding fiber (SCF) with characteristics of bend-resistance and large-mode-area (LMA) is proposed. In this new structure, the high refractive index (RI) core is periodically surrounded by high RI fan-segmented claddings. Numerical investigations show that effective single-mode operation of the proposed fiber with mode field area of 700 μm2 can be achieved when the bending radius is 15 cm. Besides, this fiber is insensitive to the bending orientation at the ranging of [-180°, 180°]. The proposed design shows great potential in high power fiber lasers and amplifiers with compact structure.

Validity of fracture toughness determined with small bend specimens

International Nuclear Information System (INIS)

Wallin, K.; Rintamaa, R.; Valo, M.

1994-02-01

This report considers the validity of fracture toughness estimates obtained with small bend specimens in relation to fracture toughness estimates obtained with large specimens. The study is based upon the analysis and comparison of actual test results. The results prove the validity of the fracture toughness determined based upon small bend specimens, especially when the results are only used to determine the fracture toughness transition temperature T o . In this case the possible error is typically less than 5 deg C and at most 10 deg C. It can be concluded that small bend specimens are very suitable for the estimation of fracture toughness in the case of brittle fracture, provided the results are corrected for statistical size effects. (orig.). (20 refs., 17 figs.)

Evaluation of River Bend Station Unit 1 Technical Specifications

International Nuclear Information System (INIS)

Baxter, D.E.; Bruske, S.J.

1985-08-01

This document was prepared for the Nuclear Regulatory Commission (NRC) to assist them in determining whether the River Bend Station Unit 1 Technical Specifications (T/S), which govern plant systems configurations and operations, are in conformance with the requirements of the Final Safety Analysis Report (FSAR) as amended, and the requirements of the Safety Evaluation Report (SER) as supplemented. A comparative audit of the FSAR as amended, and the SER as supplemented was performed with the River Bend T/S. Several discrepancies were identified and subsequently resolved through discussions with the cognizant NRC reviewer, NRC staff reviewers and/or utility representatives. The River Bend Station Unit 1 T/S, to the extent reviewed, are in conformance with the FSAR and SER

Big data challenges

DEFF Research Database (Denmark)

Bachlechner, Daniel; Leimbach, Timo

2016-01-01

Although reports on big data success stories have been accumulating in the media, most organizations dealing with high-volume, high-velocity and high-variety information assets still face challenges. Only a thorough understanding of these challenges puts organizations into a position in which...... they can make an informed decision for or against big data, and, if the decision is positive, overcome the challenges smoothly. The combination of a series of interviews with leading experts from enterprises, associations and research institutions, and focused literature reviews allowed not only...... framework are also relevant. For large enterprises and startups specialized in big data, it is typically easier to overcome the challenges than it is for other enterprises and public administration bodies....

Big Data and HPC collocation: Using HPC idle resources for Big Data Analytics

OpenAIRE

MERCIER , Michael; Glesser , David; Georgiou , Yiannis; Richard , Olivier

2017-01-01

International audience; Executing Big Data workloads upon High Performance Computing (HPC) infrastractures has become an attractive way to improve their performances. However, the collocation of HPC and Big Data workloads is not an easy task, mainly because of their core concepts' differences. This paper focuses on the challenges related to the scheduling of both Big Data and HPC workloads on the same computing platform. In classic HPC workloads, the rigidity of jobs tends to create holes in ...

Characterization of the bending strength of craniofacial sutures.

Science.gov (United States)

Maloul, Asmaa; Fialkov, Jeffrey; Whyne, Cari M

2013-03-15

The complex, thin and irregular bones of the human craniofacial skeleton (CFS) are connected together through bony articulations and connective tissues. These articulations are known as sutures and are commonly divided into two groups, facial and cranial sutures, based on their location in the CFS. CFS sutures can exhibit highly variable degrees of interdigitation and complexity and are believed to play a role in accommodating the mechanical demands of the skull. This study aimed to evaluate the mechanical behavior of CFS bone samples with and without sutures and to determine the effect of sutural interdigitations on mechanical strength. Sagittal, coronal, frontozygomatic and zygomaticotemporal sutures along with adjacent bone samples not containing sutures were excised from six fresh-frozen cadaveric heads. The interdigitation of the sutures was quantified through μCT based analysis. Three-point bending to failure was performed on a total of 29 samples. The bending strength of bone samples without sutures demonstrated a non-significant increase of 14% as compared to samples containing sutures (P=0.2). The bending strength of bones containing sutures was positively correlated to the sutural interdigitation index (R=0.701, P=0.002). The higher interdigitation indices found in human cranial vs. facial sutures may be present to resist bending loads as a functional requirement in protecting the brain. Copyright © 2012 Elsevier Ltd. All rights reserved.

Characterization of lettuce big-vein associated virus and Mirafiori lettuce big-vein virus infecting lettuce in Saudi Arabia.

Science.gov (United States)

Umar, M; Amer, M A; Al-Saleh, M A; Al-Shahwan, I M; Shakeel, M T; Zakri, A M; Katis, N I

2017-07-01

During 2014 and 2015, 97 lettuce plants that showed big-vein-disease-like symptoms and seven weed plants were collected from the Riyadh region. DAS-ELISA revealed that 25% and 9% of the lettuce plants were singly infected with LBVaV and MiLBVV, respectively, whereas 63% had a mixed infection with both viruses. The results were confirmed by multiplex reverse transcription polymerase chain reaction using primers specific for LBVaV and MiLBVV. LBVaV and MiLBVV were also detected in Sonchus oleraceus and Eruca sativa, respectively. The nucleotide sequence of LBVaV and MiLBVV Saudi isolates ranged from 94.3-100%, and their similarities to isolates with sequences in the GenBank database ranged from 93.9 to 99.6% and 93.8 to 99.3%, respectively. Olpidium sp. was present in the roots of lettuce plants with big-vein disease and it was shown to facilitate transmission of both viruses.

Big Data as Governmentality

DEFF Research Database (Denmark)

Flyverbom, Mikkel; Madsen, Anders Koed; Rasche, Andreas

This paper conceptualizes how large-scale data and algorithms condition and reshape knowledge production when addressing international development challenges. The concept of governmentality and four dimensions of an analytics of government are proposed as a theoretical framework to examine how big...... data is constituted as an aspiration to improve the data and knowledge underpinning development efforts. Based on this framework, we argue that big data’s impact on how relevant problems are governed is enabled by (1) new techniques of visualizing development issues, (2) linking aspects...... shows that big data problematizes selected aspects of traditional ways to collect and analyze data for development (e.g. via household surveys). We also demonstrate that using big data analyses to address development challenges raises a number of questions that can deteriorate its impact....

Boarding to Big data

Directory of Open Access Journals (Sweden)

Oana Claudia BRATOSIN

2016-05-01

Full Text Available Today Big data is an emerging topic, as the quantity of the information grows exponentially, laying the foundation for its main challenge, the value of the information. The information value is not only defined by the value extraction from huge data sets, as fast and optimal as possible, but also by the value extraction from uncertain and inaccurate data, in an innovative manner using Big data analytics. At this point, the main challenge of the businesses that use Big data tools is to clearly define the scope and the necessary output of the business so that the real value can be gained. This article aims to explain the Big data concept, its various classifications criteria, architecture, as well as the impact in the world wide processes.

Big data - a 21st century science Maginot Line? No-boundary thinking: shifting from the big data paradigm.

Science.gov (United States)

Huang, Xiuzhen; Jennings, Steven F; Bruce, Barry; Buchan, Alison; Cai, Liming; Chen, Pengyin; Cramer, Carole L; Guan, Weihua; Hilgert, Uwe Kk; Jiang, Hongmei; Li, Zenglu; McClure, Gail; McMullen, Donald F; Nanduri, Bindu; Perkins, Andy; Rekepalli, Bhanu; Salem, Saeed; Specker, Jennifer; Walker, Karl; Wunsch, Donald; Xiong, Donghai; Zhang, Shuzhong; Zhang, Yu; Zhao, Zhongming; Moore, Jason H

2015-01-01

Whether your interests lie in scientific arenas, the corporate world, or in government, you have certainly heard the praises of big data: Big data will give you new insights, allow you to become more efficient, and/or will solve your problems. While big data has had some outstanding successes, many are now beginning to see that it is not the Silver Bullet that it has been touted to be. Here our main concern is the overall impact of big data; the current manifestation of big data is constructing a Maginot Line in science in the 21st century. Big data is not "lots of data" as a phenomena anymore; The big data paradigm is putting the spirit of the Maginot Line into lots of data. Big data overall is disconnecting researchers and science challenges. We propose No-Boundary Thinking (NBT), applying no-boundary thinking in problem defining to address science challenges.

A Novel Rotary Piezoelectric Motor Using First Bending Hybrid Transducers

Directory of Open Access Journals (Sweden)

Yingxiang Liu

2015-08-01

Full Text Available We report a novel rotary piezoelectric motor using bending transducers in this work. Three transducers are used to drive a disk-shaped rotor together by the elliptical movements of their driving tips; these motions are produced by the hybrid of two first bending vibration modes. The proposed piezoelectric transducer has a simple structure as it only contains an aluminum alloy beam and four pieces of PZT plates. Symmetrical structure is the only necessary condition in the design process as it will ensure the resonance frequencies of the two orthogonal first bending modes are equal. Transducers with first bending resonance frequency of about 53 kHz were fabricated and assembled into a rotary motor. The proposed motor exhibits good performance on speed and torque control. Under a working frequency of 53.2 kHz, the maximum no-load speed and the maximum torque of the prototype are tested to be 53.3 rpm and of 27 mN·m.

Big Egos in Big Science

DEFF Research Database (Denmark)

Andersen, Kristina Vaarst; Jeppesen, Jacob

In this paper we investigate the micro-mechanisms governing structural evolution and performance of scientific collaboration. Scientific discovery tends not to be lead by so called lone ?stars?, or big egos, but instead by collaboration among groups of researchers, from a multitude of institutions...

Big Data and Big Science

OpenAIRE

Di Meglio, Alberto

2014-01-01

Brief introduction to the challenges of big data in scientific research based on the work done by the HEP community at CERN and how the CERN openlab promotes collaboration among research institutes and industrial IT companies. Presented at the FutureGov 2014 conference in Singapore.

BENDING BEHAVIOUR OF MAGNETIC COTTON YARNS

Directory of Open Access Journals (Sweden)

LUPU Iuliana G.

2017-05-01

Full Text Available Magnetic yarns are composite yarns, i.e. they combine elements of various natures and properties, with proven potential for electromagnetic interference (EMI shielding. In this paper, different mixtures of hard and soft magnetic powder were chosen to cover materials made of cotton yarn. The physical properties and bending behavior of the produced composite yarns were investigated in order to evaluate the yarns for further textile processing.The cotton yarn used as base material was covered with hard (barium hexaferrite BaFe12O19 and soft (Black Toner magnetic particles. An in-house developed laboratory equipment has been used to cover the twist cotton yarns with seven mixtures having different amounts of magnetic powder (30% – 50%. The bending behavior of the coated yarns was evaluated based on the average width of cracks which appeared on the yarn surface after repeated flexural tests. The obtained results revealed that usage of a polyurethane adhesive in the coating solution prevents crack formation on the surface of hard magnetic yarns after flexural tests. At the same time, the higher the mass percentage of hard magnetic powder in the mixture, the higher was the cracks’ width. The soft magnetic yarns are more flexible and a smaller crack width is observed on their surface. Both the coating solution composition and the powder diameter are expected to influence the bending behavior of coated yarns.

First multi-bend achromat lattice consideration

Energy Technology Data Exchange (ETDEWEB)

Einfeld, Dieter, E-mail: dieter.einfeld@maxlab.lu.se [Lund University, PO Box 118, Lund SE-221 00 (Sweden); Plesko, Mark [COSYLAB, Teslova ulica 30, Ljubljana SI-1000 (Slovakia); Schaper, Joachim [HAWK University of Applied Sciences and Arts, Hohnsen 4, D-31134 Hildesheim (Germany)

2014-08-27

The first proposed lattice for a ‘diffraction-limited light source’ is reported. This approach has now more or less been used for the MAX IV project. By the beginning of 1990, three third-generation synchrotron light sources had been successfully commissioned in Grenoble, Berkeley and Trieste (ESRF, ALS and ELETTRA). Each of these new machines reached their target specifications without any significant problems. In parallel, already at that time discussions were underway regarding the next generation, the ‘diffraction-limited light source (DLSR)’, which featured sub-nm rad electron beam emittance, photon beam brilliance exceeding 10{sup 22} and the potential to emit coherent radiation. Also, at about that time, a first design for a 3 GeV DLSR was developed, based on a modified multiple-bend achromat (MBA) design leading to a lattice with normalized emittance of ∊{sub x} = 0.5 nm rad. The novel feature of the MBA lattice was the use of seven vertically focusing bend magnets with different bending angles throughout the achromat cell to keep the radiation integrals and resulting beam emittance low. The baseline design called for a 400 m ring circumference with 12 straight sections of 6 m length. The dynamic aperture behaviour of the DLSR lattice was estimated to produce > 5 h beam lifetime at 100 mA stored beam current.

Forming and bending of metal foams

International Nuclear Information System (INIS)

Nebosky, Paul; Tyszka, Daniel; Niebur, Glen; Schmid, Steven

2004-01-01

This study examines the formability of a porous tantalum foam, known as trabecular metal (TM). Used as a bone ingrowth surface on orthopedic implants, TM is desirable due to its combination of high strength, low relative density, and excellent osteoconductive properties. This research aims to develop bend and stretch forming as a cost-effective alternative to net machining and EDM for manufacturing thin parts made of TM. Experimentally, bending about a single axis using a wiping die was studied by observing cracking and measuring springback. It was found that die radius and clearance strongly affect the springback properties of TM, while punch speed, embossings, die radius and clearance all influence cracking. Depending on the various combinations of die radius and clearance, springback factor ranged from .70-.91. To examine the affect of the foam microstructure, bending also was examined numerically using a horizontal hexagonal mesh. As the hexagonal cells were elongated along the sheet length, elastic springback decreased. This can be explained by the earlier onset of plastic hinging occurring at the vertices of the cells. While the numerical results matched the experimental results for the case of zero clearance, differences at higher clearances arose due to an imprecise characterization of the post-yield properties of tantalum. By changing the material properties of the struts, the models can be modified for use with other open-cell metallic foams

Challenges of Big Data Analysis.

Science.gov (United States)

Fan, Jianqing; Han, Fang; Liu, Han

2014-06-01

Big Data bring new opportunities to modern society and challenges to data scientists. On one hand, Big Data hold great promises for discovering subtle population patterns and heterogeneities that are not possible with small-scale data. On the other hand, the massive sample size and high dimensionality of Big Data introduce unique computational and statistical challenges, including scalability and storage bottleneck, noise accumulation, spurious correlation, incidental endogeneity, and measurement errors. These challenges are distinguished and require new computational and statistical paradigm. This article gives overviews on the salient features of Big Data and how these features impact on paradigm change on statistical and computational methods as well as computing architectures. We also provide various new perspectives on the Big Data analysis and computation. In particular, we emphasize on the viability of the sparsest solution in high-confidence set and point out that exogeneous assumptions in most statistical methods for Big Data can not be validated due to incidental endogeneity. They can lead to wrong statistical inferences and consequently wrong scientific conclusions.

Big data is not a monolith

CERN Document Server

Ekbia, Hamid R; Mattioli, Michael

2016-01-01

Big data is ubiquitous but heterogeneous. Big data can be used to tally clicks and traffic on web pages, find patterns in stock trades, track consumer preferences, identify linguistic correlations in large corpuses of texts. This book examines big data not as an undifferentiated whole but contextually, investigating the varied challenges posed by big data for health, science, law, commerce, and politics. Taken together, the chapters reveal a complex set of problems, practices, and policies. The advent of big data methodologies has challenged the theory-driven approach to scientific knowledge in favor of a data-driven one. Social media platforms and self-tracking tools change the way we see ourselves and others. The collection of data by corporations and government threatens privacy while promoting transparency. Meanwhile, politicians, policy makers, and ethicists are ill-prepared to deal with big data's ramifications. The contributors look at big data's effect on individuals as it exerts social control throu...

Theory of magnetoelectric effect in multilayer nanocomposites on a substrate: Resonant bending-mode response

Directory of Open Access Journals (Sweden)

Matthias C. Krantz

2013-05-01

Full Text Available Resonant bending-mode magnetoelectric (ME coefficients of magnetostrictive-piezoelectric multilayer cantilevers are calculated analytically using a model developed for arbitrary multilayers on a substrate. Without quality factor effects the ME coefficient maxima in the four-dimensional parameter space of layer numbers, layer sequences, piezoelectric volume fractions, and substrate thicknesses are found to be essentially constant for nonzero substrate thickness. Global maxima occur for bilayers without substrates. Vanishing magnetoelectric response regions result from voltage cancellation in piezoelectric layers or absence of bending-mode excitation. They are determined by the neutral plane position in the multilayer stack. With Q-factor effects dominated by viscous air damping ME coefficients strongly increase with cantilever thickness primarily due to increasing resonance frequencies. The results yield a layer specific prediction of ME coefficients, resonance frequencies, and Q-factors in arbitrary multilayers and thus distinction of linear-coupling and Q-factor effects from exchange interaction, interface, or nonlinear ME effects.

AA, bending magnet, BLG

CERN Multimedia

CERN PhotoLab

1980-01-01

The very particular lattice of the AA required 2 types of dipole (bending magnets; BLG, long and narrow; BST, short and wide). The BLG had a steel length of 4.70 m, a good field width of 0.24 m, and a weight of about 70 t. Jean-Claude Brunet inspects the lower half of a BLG. For the BST magnets see 7811105 and 8006036.

Big universe, big data

DEFF Research Database (Denmark)

Kremer, Jan; Stensbo-Smidt, Kristoffer; Gieseke, Fabian Cristian

2017-01-01

, modern astronomy requires big data know-how, in particular it demands highly efficient machine learning and image analysis algorithms. But scalability is not the only challenge: Astronomy applications touch several current machine learning research questions, such as learning from biased data and dealing......, and highlight some recent methodological advancements in machine learning and image analysis triggered by astronomical applications....

Bending Moment Decrease of Reinforced Concrete Beam Supported by Additional CFRP

Directory of Open Access Journals (Sweden)

Mykolas Daugevičius

2011-04-01

Full Text Available The calculation method of reinforced concrete beam with additional CFRP composite is proposed in this article. This method estimates tangential angular concrete deformations in tensioned beam layers between steel and bonded carbon fiber reinforced polymer. The horizontal slip of CFRP composite reduce beam bending moment capacity. An additional coefficient to reduce CFRP resultant force is necessary for better precision of bending moment capacity. Also, various calculation methods of bending moment capacity are considered. Article in Lithuanian

Poker Player Behavior After Big Wins and Big Losses

OpenAIRE

Gary Smith; Michael Levere; Robert Kurtzman

2009-01-01

We find that experienced poker players typically change their style of play after winning or losing a big pot--most notably, playing less cautiously after a big loss, evidently hoping for lucky cards that will erase their loss. This finding is consistent with Kahneman and Tversky's (Kahneman, D., A. Tversky. 1979. Prospect theory: An analysis of decision under risk. Econometrica 47(2) 263-292) break-even hypothesis and suggests that when investors incur a large loss, it might be time to take ...

Photodisintegration of deuterium and big bang nucleosynthesis

International Nuclear Information System (INIS)

Hara, K.Y.; Utsunomiya, H.; Goko, S.; Akimune, H.; Yamagata, T.; Ohta, M.; Toyokawa, H.; Kudo, K.; Uritani, A.; Shibata, Y.; Lui, Y.-W.; Ohgaki, H.

2003-01-01

Photodisintegration cross sections were measured for deuterium with Laser-Compton scattering γ beams at seven energies near threshold. Combined with the preceding data, R(E)=N a σv for the p(n,γ)D reaction is for the first time evaluated based on experimental data with 6% uncertainty in the energy region relevant to the big bang nucleosynthesis (BBN). The result confirms the theoretical evaluation on which the BBN in the precision era relies

Big Data and Chemical Education

Science.gov (United States)

Pence, Harry E.; Williams, Antony J.

2016-01-01

The amount of computerized information that organizations collect and process is growing so large that the term Big Data is commonly being used to describe the situation. Accordingly, Big Data is defined by a combination of the Volume, Variety, Velocity, and Veracity of the data being processed. Big Data tools are already having an impact in…

Regional GDP in Britain, 1871-1911: some estimates

OpenAIRE

Nicholas Crafts

2004-01-01

The paper builds on a method proposed by Geary and Stark (2002) for estimating regional incomes in Victorian Britain. This is modified by using tax data to allocate non-wage income across regions. The results suggest that the coefficient of variation of regional GDP per head was rising rapidly prior to World War I in similar fashion to the late twentieth century such that its level in 1911 and 2001 was about the same. In both episodes of globalization there were big winners and big losers amo...

Hydroforming Process for an Ultrasmall Bending Radius Elbow

Directory of Open Access Journals (Sweden)

Shangwen Ruan

2018-01-01

Full Text Available Bent pipes are widely used in automotive, aviation, and aerospace industries for delivering fluids. Parts having small relative bending radiuses are called elbows. However, fabricating a thin-walled elbow part using the simple bending process poses many challenges. One possible way to manufacture elbows is with the stamping-welding process. The major drawbacks of this method include the decline in sealing performance and the addition in weight attributed to the lap welding process. Tube hydroforming (THF is considered as a feasible solution to these problems. However, the forming process could be quite complex, and multistep forming is necessary. This study investigates the effects of preliminary processes on elbow forming such as bending, partition forming, and heat treatment and presents a high-performance optimized process design to achieve an ultrasmall radius elbow. The effects of multistep forming on the thickness distribution and the heat treatment on the microstructure have been evaluated. The results obtained from simulations show a reasonable agreement with those from the experiments.

Systematisk løbende refleksion

DEFF Research Database (Denmark)

Kristiansson, Michael

2010-01-01

Artiklen omhandler en model kaldet systematisk løbende refleksion, der repræsenterer en procedure til overvejelse og genovervejelse af de vurderingskriterier, man lægger til grund for evaluering af et udviklingsprojekt. Pointen er at justere udviklingsprojektet ind i en ønsket retning. Formålet m...

Big data in Finnish financial services

OpenAIRE

Laurila, M. (Mikko)

2017-01-01

Abstract This thesis aims to explore the concept of big data, and create understanding of big data maturity in the Finnish financial services industry. The research questions of this thesis are “What kind of big data solutions are being implemented in the Finnish financial services sector?” and “Which factors impede faster implementation of big data solutions in the Finnish financial services sector?”. ...

Big data in fashion industry

Science.gov (United States)

Jain, S.; Bruniaux, J.; Zeng, X.; Bruniaux, P.

2017-10-01

Significant work has been done in the field of big data in last decade. The concept of big data includes analysing voluminous data to extract valuable information. In the fashion world, big data is increasingly playing a part in trend forecasting, analysing consumer behaviour, preference and emotions. The purpose of this paper is to introduce the term fashion data and why it can be considered as big data. It also gives a broad classification of the types of fashion data and briefly defines them. Also, the methodology and working of a system that will use this data is briefly described.

Emittance growth of bunched beams in bends

International Nuclear Information System (INIS)

Carlsten, B.E.; Raubenheimer, T.O.

1995-01-01

Talman [Phys. Rev. Lett. 56, 1429 (1986)] has proposed a novel relativistic effect that occurs when a charged particle beam is bent in the magnetic field from an external dipole. The consequence of this effect is that the space-charge forces from the particles do not exhibit the usual inverse-square energy dependence and some part of them are, in fact, independent of energy. This led to speculation that this effect could introduce significant emittance growth for a bending electron beam. Subsequently, it was shown that this effect's influence on the beam's transverse motion is canceled for a dc beam by a potential depression within the beam (to first order in the beam radius divided by the bend radius). In this paper, we extend the analysis to include short bunch lengths (as compared to the beam pipe dimensions) and find that there is no longer the cancellation for forces both transverse to and in the direction of motion. We provide an estimate for the emittance growth as a function of bend angle, beam radius, and current, and for magnetic compression of an electron bunch

Big Defensins, a Diverse Family of Antimicrobial Peptides That Follows Different Patterns of Expression in Hemocytes of the Oyster Crassostrea gigas

Science.gov (United States)

Rosa, Rafael D.; Santini, Adrien; Fievet, Julie; Bulet, Philippe; Destoumieux-Garzón, Delphine; Bachère, Evelyne

2011-01-01

Background Big defensin is an antimicrobial peptide composed of a highly hydrophobic N-terminal region and a cationic C-terminal region containing six cysteine residues involved in three internal disulfide bridges. While big defensin sequences have been reported in various mollusk species, few studies have been devoted to their sequence diversity, gene organization and their expression in response to microbial infections. Findings Using the high-throughput Digital Gene Expression approach, we have identified in Crassostrea gigas oysters several sequences coding for big defensins induced in response to a Vibrio infection. We showed that the oyster big defensin family is composed of three members (named Cg-BigDef1, Cg-BigDef2 and Cg-BigDef3) that are encoded by distinct genomic sequences. All Cg-BigDefs contain a hydrophobic N-terminal domain and a cationic C-terminal domain that resembles vertebrate β-defensins. Both domains are encoded by separate exons. We found that big defensins form a group predominantly present in mollusks and closer to vertebrate defensins than to invertebrate and fungi CSαβ-containing defensins. Moreover, we showed that Cg-BigDefs are expressed in oyster hemocytes only and follow different patterns of gene expression. While Cg-BigDef3 is non-regulated, both Cg-BigDef1 and Cg-BigDef2 transcripts are strongly induced in response to bacterial challenge. Induction was dependent on pathogen associated molecular patterns but not damage-dependent. The inducibility of Cg-BigDef1 was confirmed by HPLC and mass spectrometry, since ions with a molecular mass compatible with mature Cg-BigDef1 (10.7 kDa) were present in immune-challenged oysters only. From our biochemical data, native Cg-BigDef1 would result from the elimination of a prepropeptide sequence and the cyclization of the resulting N-terminal glutamine residue into a pyroglutamic acid. Conclusions We provide here the first report showing that big defensins form a family of antimicrobial

Big defensins, a diverse family of antimicrobial peptides that follows different patterns of expression in hemocytes of the oyster Crassostrea gigas.

Directory of Open Access Journals (Sweden)

Rafael D Rosa

Full Text Available BACKGROUND: Big defensin is an antimicrobial peptide composed of a highly hydrophobic N-terminal region and a cationic C-terminal region containing six cysteine residues involved in three internal disulfide bridges. While big defensin sequences have been reported in various mollusk species, few studies have been devoted to their sequence diversity, gene organization and their expression in response to microbial infections. FINDINGS: Using the high-throughput Digital Gene Expression approach, we have identified in Crassostrea gigas oysters several sequences coding for big defensins induced in response to a Vibrio infection. We showed that the oyster big defensin family is composed of three members (named Cg-BigDef1, Cg-BigDef2 and Cg-BigDef3 that are encoded by distinct genomic sequences. All Cg-BigDefs contain a hydrophobic N-terminal domain and a cationic C-terminal domain that resembles vertebrate β-defensins. Both domains are encoded by separate exons. We found that big defensins form a group predominantly present in mollusks and closer to vertebrate defensins than to invertebrate and fungi CSαβ-containing defensins. Moreover, we showed that Cg-BigDefs are expressed in oyster hemocytes only and follow different patterns of gene expression. While Cg-BigDef3 is non-regulated, both Cg-BigDef1 and Cg-BigDef2 transcripts are strongly induced in response to bacterial challenge. Induction was dependent on pathogen associated molecular patterns but not damage-dependent. The inducibility of Cg-BigDef1 was confirmed by HPLC and mass spectrometry, since ions with a molecular mass compatible with mature Cg-BigDef1 (10.7 kDa were present in immune-challenged oysters only. From our biochemical data, native Cg-BigDef1 would result from the elimination of a prepropeptide sequence and the cyclization of the resulting N-terminal glutamine residue into a pyroglutamic acid. CONCLUSIONS: We provide here the first report showing that big defensins form a family

Parallel monostrand stay cable bending fatigue

DEFF Research Database (Denmark)

Winkler, Jan Pawel

This dissertation investigates the bending fatigue response of high-strength steel monostrands and multistrand stay cables to cyclic transverse deformations. Increasing bridge stock numbers and a push for longer cable-supported span lengths have led to an increased number of reported incidents...... of damage and replacement of bridge stay cables due to wind and traffic-induced fatigue. The understanding of fatigue mechanisms in most steel structures is well established. However, in the case of cables composed of steel strands, many important aspects related with bending fatigue remain to be clarified...... associated with variable loading, and different testing procedures. As most of the contemporary stay cables are comprised of a number of individual highstrength steel monostrands, the research study started with an extensive experimental work on the fatigue response of a single monostrand to cyclic flexural...

Impact of bending speed and setup on flex cracks in multilayer ceramic capacitors

DEFF Research Database (Denmark)

Andersson, Caroline; Kristensen, Ole; Varescon, Elise

2017-01-01

A comparison of bending speed and experimental setups using 3-point or 4-point bending for introduction of flex cracks into multilayer ceramic capacitors (MLCCs) in a controlled manner is presented. The impact of bending speed and corresponding strain rates on the formed flex cracks detected by X...

Big data bioinformatics.

Science.gov (United States)

Greene, Casey S; Tan, Jie; Ung, Matthew; Moore, Jason H; Cheng, Chao

2014-12-01

Recent technological advances allow for high throughput profiling of biological systems in a cost-efficient manner. The low cost of data generation is leading us to the "big data" era. The availability of big data provides unprecedented opportunities but also raises new challenges for data mining and analysis. In this review, we introduce key concepts in the analysis of big data, including both "machine learning" algorithms as well as "unsupervised" and "supervised" examples of each. We note packages for the R programming language that are available to perform machine learning analyses. In addition to programming based solutions, we review webservers that allow users with limited or no programming background to perform these analyses on large data compendia. © 2014 Wiley Periodicals, Inc.

Changing the personality of a face: Perceived Big Two and Big Five personality factors modeled in real photographs.

Science.gov (United States)

Walker, Mirella; Vetter, Thomas

2016-04-01

General, spontaneous evaluations of strangers based on their faces have been shown to reflect judgments of these persons' intention and ability to harm. These evaluations can be mapped onto a 2D space defined by the dimensions trustworthiness (intention) and dominance (ability). Here we go beyond general evaluations and focus on more specific personality judgments derived from the Big Two and Big Five personality concepts. In particular, we investigate whether Big Two/Big Five personality judgments can be mapped onto the 2D space defined by the dimensions trustworthiness and dominance. Results indicate that judgments of the Big Two personality dimensions almost perfectly map onto the 2D space. In contrast, at least 3 of the Big Five dimensions (i.e., neuroticism, extraversion, and conscientiousness) go beyond the 2D space, indicating that additional dimensions are necessary to describe more specific face-based personality judgments accurately. Building on this evidence, we model the Big Two/Big Five personality dimensions in real facial photographs. Results from 2 validation studies show that the Big Two/Big Five are perceived reliably across different samples of faces and participants. Moreover, results reveal that participants differentiate reliably between the different Big Two/Big Five dimensions. Importantly, this high level of agreement and differentiation in personality judgments from faces likely creates a subjective reality which may have serious consequences for those being perceived-notably, these consequences ensue because the subjective reality is socially shared, irrespective of the judgments' validity. The methodological approach introduced here might prove useful in various psychological disciplines. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

The BigBOSS Experiment

Energy Technology Data Exchange (ETDEWEB)

Schelgel, D.; Abdalla, F.; Abraham, T.; Ahn, C.; Allende Prieto, C.; Annis, J.; Aubourg, E.; Azzaro, M.; Bailey, S.; Baltay, C.; Baugh, C.; /APC, Paris /Brookhaven /IRFU, Saclay /Marseille, CPPM /Marseille, CPT /Durham U. / /IEU, Seoul /Fermilab /IAA, Granada /IAC, La Laguna

2011-01-01

BigBOSS will obtain observational constraints that will bear on three of the four 'science frontier' questions identified by the Astro2010 Cosmology and Fundamental Phyics Panel of the Decadal Survey: Why is the universe accelerating; what is dark matter and what are the properties of neutrinos? Indeed, the BigBOSS project was recommended for substantial immediate R and D support the PASAG report. The second highest ground-based priority from the Astro2010 Decadal Survey was the creation of a funding line within the NSF to support a 'Mid-Scale Innovations' program, and it used BigBOSS as a 'compelling' example for support. This choice was the result of the Decadal Survey's Program Priorization panels reviewing 29 mid-scale projects and recommending BigBOSS 'very highly'.

Big game hunting practices, meanings, motivations and constraints: a survey of Oregon big game hunters

Science.gov (United States)

Suresh K. Shrestha; Robert C. Burns

2012-01-01

We conducted a self-administered mail survey in September 2009 with randomly selected Oregon hunters who had purchased big game hunting licenses/tags for the 2008 hunting season. Survey questions explored hunting practices, the meanings of and motivations for big game hunting, the constraints to big game hunting participation, and the effects of age, years of hunting...

Google BigQuery analytics

CERN Document Server

Tigani, Jordan

2014-01-01

How to effectively use BigQuery, avoid common mistakes, and execute sophisticated queries against large datasets Google BigQuery Analytics is the perfect guide for business and data analysts who want the latest tips on running complex queries and writing code to communicate with the BigQuery API. The book uses real-world examples to demonstrate current best practices and techniques, and also explains and demonstrates streaming ingestion, transformation via Hadoop in Google Compute engine, AppEngine datastore integration, and using GViz with Tableau to generate charts of query results. In addit

Big data for dummies

CERN Document Server

Hurwitz, Judith; Halper, Fern; Kaufman, Marcia

2013-01-01

Find the right big data solution for your business or organization Big data management is one of the major challenges facing business, industry, and not-for-profit organizations. Data sets such as customer transactions for a mega-retailer, weather patterns monitored by meteorologists, or social network activity can quickly outpace the capacity of traditional data management tools. If you need to develop or manage big data solutions, you'll appreciate how these four experts define, explain, and guide you through this new and often confusing concept. You'll learn what it is, why it m

Analysis of critical current-bend strain relationships in composite Nb3Sn superconducting wires

International Nuclear Information System (INIS)

Luhman, T.; Welch, D.O.

1979-01-01

In order to be used successfully in fusion magnets, Nb 3 Sn conductors must meet several mechanical strain criteria, including tolerance to bending strains encountered during magnet construction. Since Nb 3 Sn is extremely brittle much information has been generated regarding the sensitivity of these conductros to tensile strain. A recent comparison of critical current-bend and tensile test data indicates that the strain required to initiate compound cracking during bending is significantly less than the strain required to do so by tensile of critical current on bending strains in monofilamentary Nb 3 Sn wires is calculated and compared with experimental data. The calculation takes into account a shift in the composite's neutral axis which occurs during bending. The analysis correctly predicts the observed depdndence of the critical current on bending strains

The Big Five of Personality and structural imaging revisited: a VBM - DARTEL study.

Science.gov (United States)

Liu, Wei-Yin; Weber, Bernd; Reuter, Martin; Markett, Sebastian; Chu, Woei-Chyn; Montag, Christian

2013-05-08

The present study focuses on the neurostructural foundations of the human personality. In a large sample of 227 healthy human individuals (168 women and 59 men), we used MRI to examine the relationship between personality traits and both regional gray and white matter volume, while controlling for age and sex. Personality was assessed using the German version of the NEO Five-Factor Inventory that measures individual differences in the 'Big Five of Personality': extraversion, neuroticism, agreeableness, conscientiousness, and openness to experience. In contrast to most previous studies on neural correlates of the Big Five, we used improved processing strategies: white and gray matter were independently assessed by segmentation steps before data analysis. In addition, customized sex-specific diffeomorphic anatomical registration using exponentiated lie algebra templates were used. Our results did not show significant correlations between any dimension of the Big Five and regional gray matter volume. However, among others, higher conscientiousness scores correlated significantly with reductions in regional white matter volume in different brain areas, including the right insula, putamen, caudate, and left fusiformis. These correlations were driven by the female subsample. The present study suggests that many results from the literature on the neurostructural basis of personality should be reviewed carefully, considering the results when the sample size is larger, imaging methods are rigorously applied, and sex-related and age-related effects are controlled.

A review of literature for the structural assessment of mitred bends

International Nuclear Information System (INIS)

Wood, J.

2008-01-01

This paper presents a state-of-the-art review of literature available for the structural assessment of all types of mitred pipe bends. Compared with smooth bends, the volume of literature available for mitres is less extensive and its scope is not as wide. Historically, this reflects a reduced application level, as well as a less demanding range of applications, such as non-high temperature use. There is also the issue that an analysis of a mitred bend is complicated by discontinuity stresses, as well as those due to cross-section ovalisation. This fact delayed the development of non-linear analysis of mitred bends. Nevertheless, there is now a substantial body of work on mitred bends. This review tabulates and characterises all publications to date in chronological order. The details of experimental specimens are highlighted, with a view to these perhaps providing useful verification data for any future finite element analysis for example. Issues of particular interest to pipework designers are discussed, including the effects of combinations of loading, out-of-circularity, tangent pipe length and flanges. Failure characteristics and loads are discussed where relevant. Topics for further research are also noted. For example, comprehensive design curves do not exist for the elastic and plastic behaviour of all mitre types, over a practical range of geometry and loading parameters. Similarly, there is still scope for further work on the effect of combined loading, end effects and out-of-circularity. Limit, collapse and burst loads are not yet available across the entire spectrum of bends and loading parameters either. Creep and optimisation represent virgin territory as far as mitred bends are concerned and given that unforeseen vibration is a common source of high-cycle fatigue failure in pipework, there must also be scope for vibration-induced fatigue studies

Bending strain study of Bi-2223/Ag tapes using Hall sensor magnetometry

International Nuclear Information System (INIS)

Lahtinen, M.; Paasi, J.; Sarkaniemi, J.; Han, Z.; Freltoft, T.

1996-01-01

The influence of room temperature bending on critical current (I c ) of Bi-2223/Ag tapes is studied by Hall sensor magnetometry, four-point method and scanning electron microscopy. Hall sensor magnetometry allows one to assess tape homogeneity and the amount of mechanical damage caused by bending. The microstructure of the Bi-2223 ceramic is found to strongly affect the tape behavior under bending strain. In a tape with moderate I c = 6.1 A at 77 K and a porous ceramic core, crack propagation took place normal to the Ag-ceramic interface, whereas in tapes with dense core, I c above 10 A at 77 K, cracks propagated in the tape plane. In monofilamentary tapes core homogeneity correlated with good bending strain performance. In multifilamentary tapes crack propagation between filaments was prohibited by the Ag matrix, thus leading to enhanced strain tolerance. In the high I c tapes studied, bending to 25 mm radius resulted in 1%--2% I c degradation

Theory of bending waves with applications to disk galaxies

International Nuclear Information System (INIS)

Mark, J.W.K.

1982-01-01

A theory of bending waves is surveyed which provides an explanation for the required amplification of the warp in the Milky Way. It also provides for self-generated warps in isolated external galaxies. The shape of observed warps and partly their existence in isolated galaxies are indicative of substantial spheroidal components. The theory also provides a plausible explanation for the bending of the inner disk (<2 kpc) of the Milky Way

Single-mode hole-assisted fiber as a bending-loss insensitive fiber

Science.gov (United States)

Nakajima, Kazuhide; Shimizu, Tomoya; Matsui, Takashi; Fukai, Chisato; Kurashima, Toshio

2010-12-01

We investigate the design and characteristics of a single-mode and low bending loss HAF both numerically and experimentally. An air filling fraction S is introduced to enable us to design a HAF with desired characteristics more easily. We show that we can expect to realize a single-mode and low bending loss HAF by considering the S dependence of the bending loss α b and cutoff wavelength λ c as well as their relative index difference Δ dependence. We also show that the mode-field diameter (MFD) and chromatic dispersion characteristics of the single-mode and low bending loss HAF can be tailored by optimizing the distance between the core and the air holes. We also investigate the usefulness of the fabricated HAFs taking the directly modulated transmission and multipath interference (MPI) characteristics into consideration. We show that the designed HAF has sufficient applicability to both analog and digital transmission systems. Our results reveal that the single-mode and low bending loss HAF is beneficial in terms of developing a future fiber to the home (FTTH) network as well as for realizing flexible optical wiring.

Exploring complex and big data

Directory of Open Access Journals (Sweden)

Stefanowski Jerzy

2017-12-01

Full Text Available This paper shows how big data analysis opens a range of research and technological problems and calls for new approaches. We start with defining the essential properties of big data and discussing the main types of data involved. We then survey the dedicated solutions for storing and processing big data, including a data lake, virtual integration, and a polystore architecture. Difficulties in managing data quality and provenance are also highlighted. The characteristics of big data imply also specific requirements and challenges for data mining algorithms, which we address as well. The links with related areas, including data streams and deep learning, are discussed. The common theme that naturally emerges from this characterization is complexity. All in all, we consider it to be the truly defining feature of big data (posing particular research and technological challenges, which ultimately seems to be of greater importance than the sheer data volume.

Was there a big bang

International Nuclear Information System (INIS)

Narlikar, J.

1981-01-01

In discussing the viability of the big-bang model of the Universe relative evidence is examined including the discrepancies in the age of the big-bang Universe, the red shifts of quasars, the microwave background radiation, general theory of relativity aspects such as the change of the gravitational constant with time, and quantum theory considerations. It is felt that the arguments considered show that the big-bang picture is not as soundly established, either theoretically or observationally, as it is usually claimed to be, that the cosmological problem is still wide open and alternatives to the standard big-bang picture should be seriously investigated. (U.K.)

BIG DATA-DRIVEN MARKETING: AN ABSTRACT

OpenAIRE

Suoniemi, Samppa; Meyer-Waarden, Lars; Munzel, Andreas

2017-01-01

Customer information plays a key role in managing successful relationships with valuable customers. Big data customer analytics use (BD use), i.e., the extent to which customer information derived from big data analytics guides marketing decisions, helps firms better meet customer needs for competitive advantage. This study addresses three research questions: What are the key antecedents of big data customer analytics use? How, and to what extent, does big data customer an...

A Temperature Sensor Based on a Polymer Optical Fiber Macro-Bend

Directory of Open Access Journals (Sweden)

Joseba Zubia Zaballa

2013-09-01

Full Text Available The design and development of a plastic optical fiber (POF macrobend temperature sensor is presented. The sensor has a linear response versus temperature at a fixed bend radius, with a sensitivity of . The sensor system used a dummy fiber-optic sensor for reference purposes having a resolution below 0.3 °C. A comprehensive experimental analysis was carried out to provide insight into the effect of different surrounding media on practical macro-bend POF sensor implementation. Experimental results are successfully compared with bend loss calculations.

Magnifying Lenses with Weak Achromatic Bends for High-Energy Electron Radiography

Energy Technology Data Exchange (ETDEWEB)

Walstrom, Peter Lowell [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-02-27

This memo briefly describes bremsstrahlung background effects in GeV-range electron radiography systems and the use of weak bending magnets to deflect the image to the side of the forward bremsstrahlung spot to reduce background. The image deflection introduces first-order chromatic image blur due to dispersion. Two approaches to eliminating the dispersion effect to first order by use of magnifying lens with achromatic bends are described. Also, higher-order image blur terms caused by weak bends are also discussed, and shown to be negligibly small in most cases of interest.

User's guide to MITRE, a stress analysis program for Mitred pipe bends

International Nuclear Information System (INIS)

Beveridge, D.C.; Carmichael, G.D.T.

1977-12-01

The MITRE computer program calculates the flexibility factor, circumferential and longitudinal inside and outside surface bending stress ratio, pressure stresses, and total stresses around the mitre section at both the mid and edge section locations of a pressurised multimitred bend under in and/or out of plane bending. Additionally, the circumferential and longitudinal strains, equivalent stress (Mises and Tresca), principal stresses, and total stresses perpendicular and parallel to the edge section at the inside and outside surfaces are calculated for the edge section. The stresses sustained by single mitres subjected to internal pressure can also be evaluated for bends with either 'long' or 'short' leg lengths. Results are tabulated and plotted in graphical form on the line printer. (author)

Big Data Analytics in Medicine and Healthcare.

Science.gov (United States)

Ristevski, Blagoj; Chen, Ming

2018-05-10

This paper surveys big data with highlighting the big data analytics in medicine and healthcare. Big data characteristics: value, volume, velocity, variety, veracity and variability are described. Big data analytics in medicine and healthcare covers integration and analysis of large amount of complex heterogeneous data such as various - omics data (genomics, epigenomics, transcriptomics, proteomics, metabolomics, interactomics, pharmacogenomics, diseasomics), biomedical data and electronic health records data. We underline the challenging issues about big data privacy and security. Regarding big data characteristics, some directions of using suitable and promising open-source distributed data processing software platform are given.

The trashing of Big Green

International Nuclear Information System (INIS)

Felten, E.

1990-01-01

The Big Green initiative on California's ballot lost by a margin of 2-to-1. Green measures lost in five other states, shocking ecology-minded groups. According to the postmortem by environmentalists, Big Green was a victim of poor timing and big spending by the opposition. Now its supporters plan to break up the bill and try to pass some provisions in the Legislature

Rotating bending fatigue strength evaluation of ceramic materials

International Nuclear Information System (INIS)

Govila, R.K.; Swank, L.R.

1995-01-01

Cyclic fatigue under rotary bending tests were conducted on partially stabilized zirconia (PSZ) from NGK and Nilsen, and silicon nitride from NGK and Norton. Fractography was performed on the failed specimens to determine the fracture structure and morphology. The results showed that the cyclic fatigue fracture was the same as the fracture structure previously observed in bending tests. The cyclic fatigue data indicated that structural ceramic could function in fatigue stress levels at a higher percentage of their average fast fracture strength than the fifty percent of ultimate strength used for wrought steels

The Big Bang Singularity

Science.gov (United States)

Ling, Eric

The big bang theory is a model of the universe which makes the striking prediction that the universe began a finite amount of time in the past at the so called "Big Bang singularity." We explore the physical and mathematical justification of this surprising result. After laying down the framework of the universe as a spacetime manifold, we combine physical observations with global symmetrical assumptions to deduce the FRW cosmological models which predict a big bang singularity. Next we prove a couple theorems due to Stephen Hawking which show that the big bang singularity exists even if one removes the global symmetrical assumptions. Lastly, we investigate the conditions one needs to impose on a spacetime if one wishes to avoid a singularity. The ideas and concepts used here to study spacetimes are similar to those used to study Riemannian manifolds, therefore we compare and contrast the two geometries throughout.

Reframing Open Big Data

DEFF Research Database (Denmark)

Marton, Attila; Avital, Michel; Jensen, Tina Blegind

2013-01-01

Recent developments in the techniques and technologies of collecting, sharing and analysing data are challenging the field of information systems (IS) research let alone the boundaries of organizations and the established practices of decision-making. Coined ‘open data’ and ‘big data......’, these developments introduce an unprecedented level of societal and organizational engagement with the potential of computational data to generate new insights and information. Based on the commonalities shared by open data and big data, we develop a research framework that we refer to as open big data (OBD......) by employing the dimensions of ‘order’ and ‘relationality’. We argue that these dimensions offer a viable approach for IS research on open and big data because they address one of the core value propositions of IS; i.e. how to support organizing with computational data. We contrast these dimensions with two...

Stresses in a curved pipe subject to an in-plane bending moment

International Nuclear Information System (INIS)

Hofmann, E.; Heeschen, U.

1979-01-01

The design of the KWU-primary component supports is mainly defined by the loads of the postulated pipe breaks. To estimate the maximum loading of a component support it is necessary to know the maximum in-plane bending moment (opening and closing) that can be transmitted by a pipe bend. Another reason for such information is that the displacements and distortions of the components cause higher stresses in elbows than in straight pipes. With a detailed knowledge of the deformation characteristic of a pipe bend an integrity analysis could be done without an expensive plastic system analysis. With this purpose in mind experiments were performed with straight pipes and pipe bends of different dimensions subject to in-plane bending moments. The experimental results give the ratio between the maximum transmittable moment of a pipe bend to that of a straight pipe or, the distortion of the end cross-sections and the flattening of the elbow cross-section. An attempt is made to derive simple expressions for estimating the behaviour at pipe elbows. Parallel to the experiments calculations were done for the straight pipe and elbow with a finite difference code with plastic capabilities. The results of the experiment and calculation are compared with the formulas of the ASME-Code section III subjection NB. (orig.)

Big Sky Carbon Sequestration Partnership

Energy Technology Data Exchange (ETDEWEB)

Susan Capalbo

2005-12-31

The Big Sky Carbon Sequestration Partnership, led by Montana State University, is comprised of research institutions, public entities and private sectors organizations, and the Confederated Salish and Kootenai Tribes and the Nez Perce Tribe. Efforts under this Partnership in Phase I are organized into four areas: (1) Evaluation of sources and carbon sequestration sinks that will be used to determine the location of pilot demonstrations in Phase II; (2) Development of GIS-based reporting framework that links with national networks; (3) Design of an integrated suite of monitoring, measuring, and verification technologies, market-based opportunities for carbon management, and an economic/risk assessment framework; (referred to below as the Advanced Concepts component of the Phase I efforts) and (4) Initiation of a comprehensive education and outreach program. As a result of the Phase I activities, the groundwork is in place to provide an assessment of storage capabilities for CO{sub 2} utilizing the resources found in the Partnership region (both geological and terrestrial sinks), that complements the ongoing DOE research agenda in Carbon Sequestration. The geology of the Big Sky Carbon Sequestration Partnership Region is favorable for the potential sequestration of enormous volume of CO{sub 2}. The United States Geological Survey (USGS 1995) identified 10 geologic provinces and 111 plays in the region. These provinces and plays include both sedimentary rock types characteristic of oil, gas, and coal productions as well as large areas of mafic volcanic rocks. Of the 10 provinces and 111 plays, 1 province and 4 plays are located within Idaho. The remaining 9 provinces and 107 plays are dominated by sedimentary rocks and located in the states of Montana and Wyoming. The potential sequestration capacity of the 9 sedimentary provinces within the region ranges from 25,000 to almost 900,000 million metric tons of CO{sub 2}. Overall every sedimentary formation investigated

The multi-bend achromat storage rings

Energy Technology Data Exchange (ETDEWEB)

Eriksson, Mikael [MAX IV Laboratory Ole Römers v. 1 22100 Lund Sweden (Sweden)

2016-07-27

Not very long ago, the 3{sup rd} generation storage ring technology was judged as mature. Most of the 3{sup rd} generation storage rings used the Double-Bend Achromat (DBA) or Triple-Bend Achromat (TBA) concepts. It was however a well-known fact that increasing the number of magnet cells in the rings is a powerful way of decreasing the electron beam emittance and thus the source brilliance, but at the penalty of increasing the size and cost of the rings. Preserving the Dynamic Aperture (DA) in the rings became also an issue when increasing the number of magnet cells. The Multi-Bend Achromat (MBA) concept, including a miniaturization of the ring elements, has now drastically changed the picture. The MBA rings, now in construction or being planned, offer orders of magnitudes higher brilliance than rings of conventional designs. Several light sources around the world are now implementing or planning to implement this MBA concept. This article touches on the science drivers for higher brilliance. We will then describe the MBA concept with its advantages as well as its challenges. A short survey of the MBA activity around the world will also be presented. The author apologies for focusing on the MAX IV project regarding technical solutions. This is motivated by that MAX IV is the facility he knows best and it might be regarded as a fore-runner for the MBA concept.

The multi-bend achromat storage rings

International Nuclear Information System (INIS)

Eriksson, Mikael

2016-01-01

Not very long ago, the 3"r"d generation storage ring technology was judged as mature. Most of the 3"r"d generation storage rings used the Double-Bend Achromat (DBA) or Triple-Bend Achromat (TBA) concepts. It was however a well-known fact that increasing the number of magnet cells in the rings is a powerful way of decreasing the electron beam emittance and thus the source brilliance, but at the penalty of increasing the size and cost of the rings. Preserving the Dynamic Aperture (DA) in the rings became also an issue when increasing the number of magnet cells. The Multi-Bend Achromat (MBA) concept, including a miniaturization of the ring elements, has now drastically changed the picture. The MBA rings, now in construction or being planned, offer orders of magnitudes higher brilliance than rings of conventional designs. Several light sources around the world are now implementing or planning to implement this MBA concept. This article touches on the science drivers for higher brilliance. We will then describe the MBA concept with its advantages as well as its challenges. A short survey of the MBA activity around the world will also be presented. The author apologies for focusing on the MAX IV project regarding technical solutions. This is motivated by that MAX IV is the facility he knows best and it might be regarded as a fore-runner for the MBA concept.

Performance of composite I-beams under axial compression and bending load modes

International Nuclear Information System (INIS)

Khalid, Y.A.; Ali, F.A.; Sahari, B.B.; Saad, E.M.A.

2005-01-01

An experimental and finite-element analyses for glass/epoxy composite I-beams have been carried out. Four, six, eight and 10 layers of woven fabric glass/epoxy composite I-beams were fabricated by a hand lay-up (molding) process. Quasi-static axial crushing and bending loading modes were used for this investigation. The load-displacement response was obtained and the energy absorption values were calculated for all the composite I-beams. Three tests were done for each composite I-beams type and each loading case for the results conformation. The second part of this study includes the elastic behavior of composite I-beams of the same dimensions and materials using finite-element analysis. The woven fabric glass/epoxy composite I-beams mechanical properties have been obtained from tensile tests. Results from this investigation show that the load required and the specific energy absorption for composite I-beams under axial compression load were higher than those for three and four point bending. On the other hand, the loads required for composite I-beams under four point bending were higher than those for three point bending, while the specific energy absorption for composite I-beams under three point bending were higher than those for four point bending. The first crushing loads difference between the experimental and finite-element results fell in the 3.6-10.92% range for axial compression tests, while fell in the 1.44-12.99% and 4.94-22.0% range for three and four point bending, respectively

Effect of cross section on collapse load in pipe bends subjected to in ...

African Journals Online (AJOL)

user

Also various researchers have estimated the plastic loads of pipe bends with cracks (Hong et al, ... In reality, the pipe bend exists with shape imperfections namely ovality and ... C t. −. = ×. (3). 3. Finite element limit analysis. Figure 1. Pipe bend with ..... Chattopadhyay J., Natahani D. K., Dutta B. K. and Kushwaha H. S. 2000.

Medical big data: promise and challenges.

Science.gov (United States)

Lee, Choong Ho; Yoon, Hyung-Jin

2017-03-01

The concept of big data, commonly characterized by volume, variety, velocity, and veracity, goes far beyond the data type and includes the aspects of data analysis, such as hypothesis-generating, rather than hypothesis-testing. Big data focuses on temporal stability of the association, rather than on causal relationship and underlying probability distribution assumptions are frequently not required. Medical big data as material to be analyzed has various features that are not only distinct from big data of other disciplines, but also distinct from traditional clinical epidemiology. Big data technology has many areas of application in healthcare, such as predictive modeling and clinical decision support, disease or safety surveillance, public health, and research. Big data analytics frequently exploits analytic methods developed in data mining, including classification, clustering, and regression. Medical big data analyses are complicated by many technical issues, such as missing values, curse of dimensionality, and bias control, and share the inherent limitations of observation study, namely the inability to test causality resulting from residual confounding and reverse causation. Recently, propensity score analysis and instrumental variable analysis have been introduced to overcome these limitations, and they have accomplished a great deal. Many challenges, such as the absence of evidence of practical benefits of big data, methodological issues including legal and ethical issues, and clinical integration and utility issues, must be overcome to realize the promise of medical big data as the fuel of a continuous learning healthcare system that will improve patient outcome and reduce waste in areas including nephrology.

Medical big data: promise and challenges

Directory of Open Access Journals (Sweden)

Choong Ho Lee

2017-03-01

Full Text Available The concept of big data, commonly characterized by volume, variety, velocity, and veracity, goes far beyond the data type and includes the aspects of data analysis, such as hypothesis-generating, rather than hypothesis-testing. Big data focuses on temporal stability of the association, rather than on causal relationship and underlying probability distribution assumptions are frequently not required. Medical big data as material to be analyzed has various features that are not only distinct from big data of other disciplines, but also distinct from traditional clinical epidemiology. Big data technology has many areas of application in healthcare, such as predictive modeling and clinical decision support, disease or safety surveillance, public health, and research. Big data analytics frequently exploits analytic methods developed in data mining, including classification, clustering, and regression. Medical big data analyses are complicated by many technical issues, such as missing values, curse of dimensionality, and bias control, and share the inherent limitations of observation study, namely the inability to test causality resulting from residual confounding and reverse causation. Recently, propensity score analysis and instrumental variable analysis have been introduced to overcome these limitations, and they have accomplished a great deal. Many challenges, such as the absence of evidence of practical benefits of big data, methodological issues including legal and ethical issues, and clinical integration and utility issues, must be overcome to realize the promise of medical big data as the fuel of a continuous learning healthcare system that will improve patient outcome and reduce waste in areas including nephrology.

What is beyond the big five?

Science.gov (United States)

Saucier, G; Goldberg, L R

1998-08-01

Previous investigators have proposed that various kinds of person-descriptive content--such as differences in attitudes or values, in sheer evaluation, in attractiveness, or in height and girth--are not adequately captured by the Big Five Model. We report on a rather exhaustive search for reliable sources of Big Five-independent variation in data from person-descriptive adjectives. Fifty-three candidate clusters were developed in a college sample using diverse approaches and sources. In a nonstudent adult sample, clusters were evaluated with respect to a minimax criterion: minimum multiple correlation with factors from Big Five markers and maximum reliability. The most clearly Big Five-independent clusters referred to Height, Girth, Religiousness, Employment Status, Youthfulness and Negative Valence (or low-base-rate attributes). Clusters referring to Fashionableness, Sensuality/Seductiveness, Beauty, Masculinity, Frugality, Humor, Wealth, Prejudice, Folksiness, Cunning, and Luck appeared to be potentially beyond the Big Five, although each of these clusters demonstrated Big Five multiple correlations of .30 to .45, and at least one correlation of .20 and over with a Big Five factor. Of all these content areas, Religiousness, Negative Valence, and the various aspects of Attractiveness were found to be represented by a substantial number of distinct, common adjectives. Results suggest directions for supplementing the Big Five when one wishes to extend variable selection outside the domain of personality traits as conventionally defined.

Big Data Analytics and Its Applications

Directory of Open Access Journals (Sweden)

Mashooque A. Memon

2017-10-01

Full Text Available The term, Big Data, has been authored to refer to the extensive heave of data that can't be managed by traditional data handling methods or techniques. The field of Big Data plays an indispensable role in various fields, such as agriculture, banking, data mining, education, chemistry, finance, cloud computing, marketing, health care stocks. Big data analytics is the method for looking at big data to reveal hidden patterns, incomprehensible relationship and other important data that can be utilize to resolve on enhanced decisions. There has been a perpetually expanding interest for big data because of its fast development and since it covers different areas of applications. Apache Hadoop open source technology created in Java and keeps running on Linux working framework was used. The primary commitment of this exploration is to display an effective and free solution for big data application in a distributed environment, with its advantages and indicating its easy use. Later on, there emerge to be a required for an analytical review of new developments in the big data technology. Healthcare is one of the best concerns of the world. Big data in healthcare imply to electronic health data sets that are identified with patient healthcare and prosperity. Data in the healthcare area is developing past managing limit of the healthcare associations and is relied upon to increment fundamentally in the coming years.

Measuring the Promise of Big Data Syllabi

Science.gov (United States)

Friedman, Alon

2018-01-01

Growing interest in Big Data is leading industries, academics and governments to accelerate Big Data research. However, how teachers should teach Big Data has not been fully examined. This article suggests criteria for redesigning Big Data syllabi in public and private degree-awarding higher education establishments. The author conducted a survey…

Decagonal quasicrystal plate with elliptic holes subjected to out-of-plane bending moments

Energy Technology Data Exchange (ETDEWEB)

Li, Lian He, E-mail: nmglilianhe@163.com [College of Mathematics Science, Inner Mongolia Normal University, Hohhot 010022 (China); College of Physical Science and Technology, Inner Mongolia University, Hohhot 010021 (China); Inner Mongolia Key Lab of Nanoscience and Nanotechnology, Hohhot 010021 (China); Liu, Guan Ting [College of Mathematics Science, Inner Mongolia Normal University, Hohhot 010022 (China)

2014-02-01

In the present paper, we consider only the ideal elastic behavior, neglecting the dissipation associated with the atomic rearrangements. Under these conditions, the decagonal quasicrystal plate bending problems have been discussed. The Stroh-like formalism for the bending theory of decagonal quasicrystal plate is developed. The analytical solutions for problems of decagonal quasicrystal plate with elliptic hole subjected to out-of-plane bending moments are obtained directly by using the forms. The resultant bending moments around the hole boundaries are also given explicitly. When the phonon–phason coupling is absent, the results reduce to the corresponding solutions for the isotropic elastic plates.

All-fiber intensity bend sensor based on photonic crystal fiber with asymmetric air-hole structure

Science.gov (United States)

Budnicki, Dawid; Szostkiewicz, Lukasz; Szymanski, Michal O.; Ostrowski, Lukasz; Holdynski, Zbigniew; Lipinski, Stanislaw; Murawski, Michal; Wojcik, Grzegorz; Makara, Mariusz; Poturaj, Krzysztof; Mergo, Pawel; Napierala, Marek; Nasilowski, Tomasz

2017-10-01

Monitoring the geometry of an moving element is a crucial task for example in robotics. The robots equipped with fiber bend sensor integrated in their arms can be a promising solution for medicine, physiotherapy and also for application in computer games. We report an all-fiber intensity bend sensor, which is based on microstructured multicore optical fiber. It allows to perform a measurement of the bending radius as well as the bending orientation. The reported solution has a special airhole structure which makes the sensor only bend-sensitive. Our solution is an intensity based sensor, which measures power transmitted along the fiber, influenced by bend. The sensor is based on a multicore fiber with the special air-hole structure that allows detection of bending orientation in range of 360°. Each core in the multicore fiber is sensitive to bend in specified direction. The principle behind sensor operation is to differentiate the confinement loss of fundamental mode propagating in each core. Thanks to received power differences one can distinguish not only bend direction but also its amplitude. Multicore fiber is designed to utilize most common light sources that operate at 1.55 μm thus ensuring high stability of operation. The sensitivity of the proposed solution is equal 29,4 dB/cm and the accuracy of bend direction for the fiber end point is up to 5 degrees for 15 cm fiber length. Such sensitivity allows to perform end point detection with millimeter precision.

Ketahanan Bending Komposit Hybrid Serat Batang Kelapa/Serat Gelas Dengan Matrik Urea Formaldehyde

Directory of Open Access Journals (Sweden)

Nasmi Herlina Sari

2012-11-01

Full Text Available The composite has its own advantages compared to other alternative techniques such material is strong, lightweight,corrosion-resistant, economical and so on. The purpose of this study was to investigate the characteristics of bending strengthfiber composite hybrid coconut trunk / fiber glass using urea formaldehyde resin.Hybrid palm trunk fiber /glass fiber composite have been made by hand lay up which volume fraction fiber hybridvariation namely 10:20, 15:15 and 20:10 (% with length fiber 2 cm. Every Tests conducted were bending testing with eachvariation performed three times repetition. Bending test specimens in accordance with standard ASTMD 790.The results of bending strength of palm trunk fiber hybrid composite / fiber-glass with random fiber direction that thehighest bending strength in the palm trunk fiber volume fraction 10% and 20% glass fiber that is 22.7 N/mm2.

Analysis of Variscan dynamics; early bending of the Cantabria-Asturias Arc, northern Spain

Science.gov (United States)

Kollmeier, J. M.; van der Pluijm, B. A.; Van der Voo, R.

2000-08-01

Calcite twinning analysis in the Cantabria-Asturias Arc (CAA) of northern Spain provides a basis for evaluating conditions of Variscan stress and constrains the arc's structural evolution. Twinning typically occurs during earliest layer-parallel shortening, offering the ability to define early conditions of regional stress. Results from the Somiedo-Correcilla region are of two kinds: early maximum compressive stress oriented layer-parallel and at high angles to bedding strike (D1 σ1) and later twin producing compression oriented sub-parallel to strike (D2 σ1). When all D1 compressions are rotated into a uniform east-west reference orientation, a quite linear, north-south trending fold-thrust belt results showing a slight deflection of the southern zone to the south-southeast. North-south-directed D2 σ1 compression was recorded prior to bending of the belt. Calcite twinning data elucidate earliest structural conditions that could not be obtained by other means, whereas the kinematics of arc tightening during D2 is constrained by paleomagnetism. A large and perhaps protracted D2 σ1 is suggested by our results, as manifested by approximately 50% arc tightening prior to acquisition of paleomagnetic remagnetizations throughout the CAA. Early east-west compression (D1 σ1) likely resulted from the Ebro-Aquitaine massif docking to Laurussia whereas the north-directed collision of Africa (D2 σ1) produced clockwise bending in the northern zone, radial folding in the hinge, and rotation of thrusts in the southern zone.

Effect of nonlinear stress-strain relationship on bending strength of isotropic graphite

International Nuclear Information System (INIS)

Arai, Taketoshi; Oku, Tatsuo

1978-05-01

Four-point bending tests were made on rectangular isotropic 7477PT graphite specimens of different sizes to observe the relation between load and outermost fiber strain. Analytical methods, allowing for nonlinear stress-strain relationships different between tension and compression, were developed for calculating the fiber stress distribution in a beam and the failure probability based on the Weibull statistical theory for bending fracture. With increase of the stress, the stress-strain curves for tension deviate from the linearity and also from those for compression. The true bending strengths of the rectangular bars are 10 -- 20 percent lower than elastic bending strengths. Revised Weibull theory gives failure probability distributions agreeing with measured ones, compared with the theory based on elastic behavior. (auth.)

77 FR 27245 - Big Stone National Wildlife Refuge, Big Stone and Lac Qui Parle Counties, MN

Science.gov (United States)

2012-05-09

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R3-R-2012-N069; FXRS1265030000S3-123-FF03R06000] Big Stone National Wildlife Refuge, Big Stone and Lac Qui Parle Counties, MN AGENCY: Fish and... plan (CCP) and environmental assessment (EA) for Big Stone National Wildlife Refuge (Refuge, NWR) for...

Improvement of the bending fatigue resistance of the hyper-eutectoid steel wires used for tire cords by a post-processing annealing

International Nuclear Information System (INIS)

Yang, Y.S.; Bae, J.G.; Park, C.G.

2008-01-01

In this study, the effects of annealing at a low temperature on the bending fatigue resistance have been investigated in the hyper-eutectoid steel wires drawn to an extreme strain of 4.12. The annealing temperature was varied from 100 to 500 deg. C. The bending fatigue resistance of the steel wires was measured by a Hunter rotating beam tester specially designed for thin-sized steel wires. The results showed that fatigue resistance as well as tensile strength improved as the annealing temperature increased up to 200 deg. C (Region I) and gradually decreased after annealing above 200 deg. C (Region II). In order to elucidate this behavior, residual stress was measured by dual beam FIB, surface defects observed by an optical 3D profiler and the microstructure in terms of lamellar spacing (λ p ) and cementite thickness (t c ) was observed by TEM

Photoelastic investigation of the stresses in mitred bent-cylinders under bending, 2

International Nuclear Information System (INIS)

Sawa, Yoshiaki

1984-01-01

The states of stress distribution in mitred bend subjected to inplane uniform bending moment have been studied systematically by means of photoelastic stress freezing method. The relations between the stress concentration factor of fiber stress σsub(l) and of hoop stress σsub(theta) near the bent part and the angle of mitred bend are thoroughly investigated. The effects of fillet radius of the bent-part and wall thickness on the stress concentration factors are also discussed. (author)

The BigBoss Experiment

Energy Technology Data Exchange (ETDEWEB)

Schelgel, D.; Abdalla, F.; Abraham, T.; Ahn, C.; Allende Prieto, C.; Annis, J.; Aubourg, E.; Azzaro, M.; Bailey, S.; Baltay, C.; Baugh, C.; Bebek, C.; Becerril, S.; Blanton, M.; Bolton, A.; Bromley, B.; Cahn, R.; Carton, P.-H.; Cervanted-Cota, J.L.; Chu, Y.; Cortes, M.; /APC, Paris /Brookhaven /IRFU, Saclay /Marseille, CPPM /Marseille, CPT /Durham U. / /IEU, Seoul /Fermilab /IAA, Granada /IAC, La Laguna / /IAC, Mexico / / /Madrid, IFT /Marseille, Lab. Astrophys. / / /New York U. /Valencia U.

2012-06-07

BigBOSS is a Stage IV ground-based dark energy experiment to study baryon acoustic oscillations (BAO) and the growth of structure with a wide-area galaxy and quasar redshift survey over 14,000 square degrees. It has been conditionally accepted by NOAO in response to a call for major new instrumentation and a high-impact science program for the 4-m Mayall telescope at Kitt Peak. The BigBOSS instrument is a robotically-actuated, fiber-fed spectrograph capable of taking 5000 simultaneous spectra over a wavelength range from 340 nm to 1060 nm, with a resolution R = {lambda}/{Delta}{lambda} = 3000-4800. Using data from imaging surveys that are already underway, spectroscopic targets are selected that trace the underlying dark matter distribution. In particular, targets include luminous red galaxies (LRGs) up to z = 1.0, extending the BOSS LRG survey in both redshift and survey area. To probe the universe out to even higher redshift, BigBOSS will target bright [OII] emission line galaxies (ELGs) up to z = 1.7. In total, 20 million galaxy redshifts are obtained to measure the BAO feature, trace the matter power spectrum at smaller scales, and detect redshift space distortions. BigBOSS will provide additional constraints on early dark energy and on the curvature of the universe by measuring the Ly-alpha forest in the spectra of over 600,000 2.2 < z < 3.5 quasars. BigBOSS galaxy BAO measurements combined with an analysis of the broadband power, including the Ly-alpha forest in BigBOSS quasar spectra, achieves a FOM of 395 with Planck plus Stage III priors. This FOM is based on conservative assumptions for the analysis of broad band power (k{sub max} = 0.15), and could grow to over 600 if current work allows us to push the analysis to higher wave numbers (k{sub max} = 0.3). BigBOSS will also place constraints on theories of modified gravity and inflation, and will measure the sum of neutrino masses to 0.024 eV accuracy.

Investigation of hydrodynamics on local scour by shape of single spur dike in river bend

International Nuclear Information System (INIS)

Masjedi, A; Foroushani, E P

2012-01-01

A series of experiments were conducted in which the the scour hole associated with model spur dike was measured in a 180 degree laboratory flume bend under clear-water overtopping flows. In this study, the local scour were conducted for three different shapes of oblong, rectangulat chamfered of straight spur dikes at the bend with various Froude number. The main goals of the experiments were to evaluate the effect of the three different shapes of straight spur dikes on the volume of scour and potential aquatic habitat and on minimizing erosion adjacent to the streambanks. The experiments showed that of the three different shapes of straight spur dikes tested, the least erosion of the around in the near bank region was associated with the spur dikes with oblong shape, while the greatest volume of the scour hole was associated with the rectangular shape. So it was observed that, as Froude number increases, the scour increases.

Stereotypical reaching movements of the octopus involve both bend propagation and arm elongation.

Science.gov (United States)

Hanassy, S; Botvinnik, A; Flash, T; Hochner, B

2015-05-13

The bend propagation involved in the stereotypical reaching movement of the octopus arm has been extensively studied. While these studies have analyzed the kinematics of bend propagation along the arm during its extension, possible length changes have been ignored. Here, the elongation profiles of the reaching movements of Octopus vulgaris were assessed using three-dimensional reconstructions. The analysis revealed that, in addition to bend propagation, arm extension movements involve elongation of the proximal part of the arm, i.e., the section from the base of the arm to the propagating bend. The elongations are quite substantial and highly variable, ranging from an average strain along the arm of -0.12 (i.e. shortening) up to 1.8 at the end of the movement (0.57 ± 0.41, n = 64 movements, four animals). Less variability was discovered in an additional set of experiments on reaching movements (0.64 ± 0.28, n = 30 movements, two animals), where target and octopus positions were kept more stationary. Visual observation and subsequent kinematic analysis suggest that the reaching movements can be broadly segregated into two groups. The first group involves bend propagation beginning at the base of the arm and propagating towards the arm tip. In the second, the bend is formed or present more distally and reaching is achieved mainly by elongation and straightening of the segment proximal to the bend. Only in the second type of movements is elongation significantly positively correlated with the distance of the bend from the target. We suggest that reaching towards a target is generated by a combination of both propagation of a bend along the arm and arm elongation. These two motor primitives may be combined to create a broad spectrum of reaching movements. The dynamical model, which recapitulates the biomechanics of the octopus muscular hydrostatic arm, suggests that achieving the observed elongation requires an extremely low ratio of longitudinal to transverse muscle

Bend-imitating theory and electron scattering in sharply-bent quantum nanowires

International Nuclear Information System (INIS)

Vakhnenko, O.O.

2011-01-01

The concept of bend-imitating description as applied to the one-electron quantum mechanics in sharply-bent ideal electron waveguides and its development into a self consistent theory are presented. In the framework of bend-imitating approach, the investigation of the electron scattering in a doubly-bent 2D quantum wire with S-like bend has been made, and the explicit dependences of the transmission and reflection coefficients on geometrical parameters of a structure, as well as on the electron energy, have been obtained. The total elimination of the mixing between the scattering channels of a S-like bent quantum wire is predicted.

A Temperature Sensor Based on a Polymer Optical Fiber Macro-Bend

Science.gov (United States)

Moraleda, Alberto Tapetado; García, Carmen Vázquez; Zaballa, Joseba Zubia; Arrue, Jon

2013-01-01

The design and development of a plastic optical fiber (POF) macrobend temperature sensor is presented. The sensor has a linear response versus temperature at a fixed bend radius, with a sensitivity of 1.92·10−3 (°C)−1. The sensor system used a dummy fiber-optic sensor for reference purposes having a resolution below 0.3 °C. A comprehensive experimental analysis was carried out to provide insight into the effect of different surrounding media on practical macro-bend POF sensor implementation. Experimental results are successfully compared with bend loss calculations. PMID:24077323

Big data and educational research

OpenAIRE

Beneito-Montagut, Roser

2017-01-01

Big data and data analytics offer the promise to enhance teaching and learning, improve educational research and progress education governance. This chapter aims to contribute to the conceptual and methodological understanding of big data and analytics within educational research. It describes the opportunities and challenges that big data and analytics bring to education as well as critically explore the perils of applying a data driven approach to education. Despite the claimed value of the...

Monitoring static shape memory polymers using a fiber Bragg grating as a vector-bending sensor

Science.gov (United States)

Li, Peng; Yan, Zhijun; Zhou, Kaiming; Zhang, Lin; Leng, Jinsong

2013-01-01

We propose and demonstrate a technique for monitoring the recovery deformation of the shape-memory polymers (SMP) using a surface-attached fiber Bragg grating (FBG) as a vector-bending sensor. The proposed sensing scheme could monitor the pure bending deformation for the SMP sample. When the SMP sample undergoes concave or convex bending, the resonance wavelength of the FBG will have red-shift or blue-shift according to the tensile or compressive stress gradient along the FBG. As the results show, the bending sensitivity is around 4.07 nm/cm-1. The experimental results clearly indicate that the deformation of such an SMP sample can be effectively monitored by the attached FBG not just for the bending curvature but also the bending direction.

Thick-Big Descriptions

DEFF Research Database (Denmark)

Lai, Signe Sophus

The paper discusses the rewards and challenges of employing commercial audience measurements data – gathered by media industries for profitmaking purposes – in ethnographic research on the Internet in everyday life. It questions claims to the objectivity of big data (Anderson 2008), the assumption...... communication systems, language and behavior appear as texts, outputs, and discourses (data to be ‘found’) – big data then documents things that in earlier research required interviews and observations (data to be ‘made’) (Jensen 2014). However, web-measurement enterprises build audiences according...... to a commercial logic (boyd & Crawford 2011) and is as such directed by motives that call for specific types of sellable user data and specific segmentation strategies. In combining big data and ‘thick descriptions’ (Geertz 1973) scholars need to question how ethnographic fieldwork might map the ‘data not seen...

Polarization measurement and vertical aperture optimization for obtaining circularly polarized bend-magnet radiation

Energy Technology Data Exchange (ETDEWEB)

Kortright, J.B.; Rice, M.; Hussain, Z. [Lawrence Berkeley National Lab., CA (United States)] [and others

1997-04-01

Growing interest in utilizing circular polarization prompted the design of bend-magnet beamline 9.3.2 at the Advanced Light Source, covering the 30-1500 eV spectral region, to include vertical aperturing capabilities for optimizing the collection of circular polarization above and below the orbit plane. After commissioning and early use of the beamline, a multilayer polarimeter was used to characterize the polarization state of the beam as a function of vertical aperture position. This report partially summarizes the polarimetry measurements and compares results with theoretical calculations intended to simulate experimental conditions.

Big Data's Role in Precision Public Health.

Science.gov (United States)

Dolley, Shawn

2018-01-01

Precision public health is an emerging practice to more granularly predict and understand public health risks and customize treatments for more specific and homogeneous subpopulations, often using new data, technologies, and methods. Big data is one element that has consistently helped to achieve these goals, through its ability to deliver to practitioners a volume and variety of structured or unstructured data not previously possible. Big data has enabled more widespread and specific research and trials of stratifying and segmenting populations at risk for a variety of health problems. Examples of success using big data are surveyed in surveillance and signal detection, predicting future risk, targeted interventions, and understanding disease. Using novel big data or big data approaches has risks that remain to be resolved. The continued growth in volume and variety of available data, decreased costs of data capture, and emerging computational methods mean big data success will likely be a required pillar of precision public health into the future. This review article aims to identify the precision public health use cases where big data has added value, identify classes of value that big data may bring, and outline the risks inherent in using big data in precision public health efforts.

Numerical and experimental study on multi-pass laser bending of AH36 steel strips

Science.gov (United States)

Fetene, Besufekad N.; Kumar, Vikash; Dixit, Uday S.; Echempati, Raghu

2018-02-01

Laser bending is a process of bending of plates, small sized sheets, strips and tubes, in which a moving or stationary laser beam heats the workpiece to achieve the desired curvature due to thermal stresses. Researchers studied the effects of different process parameters related to the laser source, material and workpiece geometry on laser bending of metal sheets. The studies are focused on large sized sheets. The workpiece geometry parameters like sheet thickness, length and width also affect the bend angle considerably. In this work, the effects of width and thickness on multi-pass laser bending of AH36 steel strips were studied experimentally and numerically. Finite element model using ABAQUS® was developed to investigate the size effect on the prediction of the bend angle. Microhardness and flexure tests showed an increase in the flexural strength as well as microhardness in the scanned zone. The microstructures of the bent strips also supported the physical observations.

Origin of bending in uncoated microcantilever - Surface topography?

International Nuclear Information System (INIS)

Lakshmoji, K.; Prabakar, K.; Tripura Sundari, S.; Jayapandian, J.; Tyagi, A. K.; Sundar, C. S.

2014-01-01

We provide direct experimental evidence to show that difference in surface topography on opposite sides of an uncoated microcantilever induces bending, upon exposure to water molecules. Examination on opposite sides of the microcantilever by atomic force microscopy reveals the presence of localized surface features on one side, which renders the induced stress non-uniform. Further, the root mean square inclination angle characterizing the surface topography shows a difference of 73° between the opposite sides. The absence of deflection in another uncoated microcantilever having similar surface topography confirms that in former microcantilever bending is indeed induced by differences in surface topography

Big Data, indispensable today

Directory of Open Access Journals (Sweden)

Radu-Ioan ENACHE

2015-10-01

Full Text Available Big data is and will be used more in the future as a tool for everything that happens both online and offline. Of course , online is a real hobbit, Big Data is found in this medium , offering many advantages , being a real help for all consumers. In this paper we talked about Big Data as being a plus in developing new applications, by gathering useful information about the users and their behaviour.We've also presented the key aspects of real-time monitoring and the architecture principles of this technology. The most important benefit brought to this paper is presented in the cloud section.

Antigravity and the big crunch/big bang transition

Science.gov (United States)

Bars, Itzhak; Chen, Shih-Hung; Steinhardt, Paul J.; Turok, Neil

2012-08-01

We point out a new phenomenon which seems to be generic in 4d effective theories of scalar fields coupled to Einstein gravity, when applied to cosmology. A lift of such theories to a Weyl-invariant extension allows one to define classical evolution through cosmological singularities unambiguously, and hence construct geodesically complete background spacetimes. An attractor mechanism ensures that, at the level of the effective theory, generic solutions undergo a big crunch/big bang transition by contracting to zero size, passing through a brief antigravity phase, shrinking to zero size again, and re-emerging into an expanding normal gravity phase. The result may be useful for the construction of complete bouncing cosmologies like the cyclic model.

Antigravity and the big crunch/big bang transition

Energy Technology Data Exchange (ETDEWEB)

Bars, Itzhak [Department of Physics and Astronomy, University of Southern California, Los Angeles, CA 90089-2535 (United States); Chen, Shih-Hung [Perimeter Institute for Theoretical Physics, Waterloo, ON N2L 2Y5 (Canada); Department of Physics and School of Earth and Space Exploration, Arizona State University, Tempe, AZ 85287-1404 (United States); Steinhardt, Paul J., E-mail: steinh@princeton.edu [Department of Physics and Princeton Center for Theoretical Physics, Princeton University, Princeton, NJ 08544 (United States); Turok, Neil [Perimeter Institute for Theoretical Physics, Waterloo, ON N2L 2Y5 (Canada)

2012-08-29

We point out a new phenomenon which seems to be generic in 4d effective theories of scalar fields coupled to Einstein gravity, when applied to cosmology. A lift of such theories to a Weyl-invariant extension allows one to define classical evolution through cosmological singularities unambiguously, and hence construct geodesically complete background spacetimes. An attractor mechanism ensures that, at the level of the effective theory, generic solutions undergo a big crunch/big bang transition by contracting to zero size, passing through a brief antigravity phase, shrinking to zero size again, and re-emerging into an expanding normal gravity phase. The result may be useful for the construction of complete bouncing cosmologies like the cyclic model.

Antigravity and the big crunch/big bang transition

International Nuclear Information System (INIS)

Bars, Itzhak; Chen, Shih-Hung; Steinhardt, Paul J.; Turok, Neil

2012-01-01

We point out a new phenomenon which seems to be generic in 4d effective theories of scalar fields coupled to Einstein gravity, when applied to cosmology. A lift of such theories to a Weyl-invariant extension allows one to define classical evolution through cosmological singularities unambiguously, and hence construct geodesically complete background spacetimes. An attractor mechanism ensures that, at the level of the effective theory, generic solutions undergo a big crunch/big bang transition by contracting to zero size, passing through a brief antigravity phase, shrinking to zero size again, and re-emerging into an expanding normal gravity phase. The result may be useful for the construction of complete bouncing cosmologies like the cyclic model.

OM4 bend insensitive multi-mode fibers’ usefulness for MCM integration

International Nuclear Information System (INIS)

Guzowski, Bartłomiej; Lisik, Zbigniew; Tosik, Grzegorz; Ciupa, Emilia

2012-01-01

Highlights: ► The influence of high temperature exposure on OM4 fibers’ mechanical properties. ► Researching OM4 class fibers for use in innovative Optical Multi Chip Module. ► The influence of bending at a very small radius, up to 2 mm, on MM fibers. - Abstract: For future generations of electronic systems, a severe bottleneck is expected on the interconnection level and the use of optical interconnection is considered as one of the most promising solutions in this matter. Recent progress in fiber development resulted in new generation of optical fibers that are bend insensitive. This makes them ideal for Multi Chip Module (MCM) application. This paper focuses on OM4 bend insensitive multi-mode fibers’ usefulness for MCM integration, particularly the investigation of MM fiber loss is presented, which is influenced by bend diameter and the fiber's mechanical performance under influence of high temperature (400 °C–1000 °C adequate to MCM production process).

Big data: een zoektocht naar instituties

NARCIS (Netherlands)

van der Voort, H.G.; Crompvoets, J

2016-01-01

Big data is a well-known phenomenon, even a buzzword nowadays. It refers to an abundance of data and new possibilities to process and use them. Big data is subject of many publications. Some pay attention to the many possibilities of big data, others warn us for their consequences. This special

Data, Data, Data : Big, Linked & Open

NARCIS (Netherlands)

Folmer, E.J.A.; Krukkert, D.; Eckartz, S.M.

2013-01-01

De gehele business en IT-wereld praat op dit moment over Big Data, een trend die medio 2013 Cloud Computing is gepasseerd (op basis van Google Trends). Ook beleidsmakers houden zich actief bezig met Big Data. Neelie Kroes, vice-president van de Europese Commissie, spreekt over de ‘Big Data

Quality of Big Data in health care.

Science.gov (United States)

Sukumar, Sreenivas R; Natarajan, Ramachandran; Ferrell, Regina K

2015-01-01

The current trend in Big Data analytics and in particular health information technology is toward building sophisticated models, methods and tools for business, operational and clinical intelligence. However, the critical issue of data quality required for these models is not getting the attention it deserves. The purpose of this paper is to highlight the issues of data quality in the context of Big Data health care analytics. The insights presented in this paper are the results of analytics work that was done in different organizations on a variety of health data sets. The data sets include Medicare and Medicaid claims, provider enrollment data sets from both public and private sources, electronic health records from regional health centers accessed through partnerships with health care claims processing entities under health privacy protected guidelines. Assessment of data quality in health care has to consider: first, the entire lifecycle of health data; second, problems arising from errors and inaccuracies in the data itself; third, the source(s) and the pedigree of the data; and fourth, how the underlying purpose of data collection impact the analytic processing and knowledge expected to be derived. Automation in the form of data handling, storage, entry and processing technologies is to be viewed as a double-edged sword. At one level, automation can be a good solution, while at another level it can create a different set of data quality issues. Implementation of health care analytics with Big Data is enabled by a road map that addresses the organizational and technological aspects of data quality assurance. The value derived from the use of analytics should be the primary determinant of data quality. Based on this premise, health care enterprises embracing Big Data should have a road map for a systematic approach to data quality. Health care data quality problems can be so very specific that organizations might have to build their own custom software or data

A wave-bending structure at Ka-band using 3D-printed metamaterial

Science.gov (United States)

Wu, Junqiang; Liang, Min; Xin, Hao

2018-03-01

Three-dimensional printing technologies enable metamaterials of complex structures with arbitrary inhomogeneity. In this work, a 90° wave-bending structure at the Ka-band (26.5-40 GHz) based on 3D-printed metamaterials is designed, fabricated, and measured. The wave-bending effect is realized through a spatial distribution of varied effective dielectric constants. Based on the effective medium theory, different effective dielectric constants are accomplished by special, 3D-printable unit cells, which allow different ratios of dielectric to air at the unit cell level. In contrast to traditional, metallic-structure-included metamaterial designs, the reported wave-bending structure here is all dielectric and implemented by the polymer-jetting technique, which features rapid, low-cost, and convenient prototyping. Both simulation and experiment results demonstrate the effectiveness of the wave-bending structure.

Angular dependent XPS study of surface band bending on Ga-polar n-GaN

Science.gov (United States)

Huang, Rong; Liu, Tong; Zhao, Yanfei; Zhu, Yafeng; Huang, Zengli; Li, Fangsen; Liu, Jianping; Zhang, Liqun; Zhang, Shuming; Dingsun, An; Yang, Hui

2018-05-01

Surface band bending and composition of Ga-polar n-GaN with different surface treatments were characterized by using angular dependent X-ray photoelectron spectroscopy. Upward surface band bending of varying degree was observed distinctly upon to the treatment methods. Besides the nitrogen vacancies, we found that surface states of oxygen-containing absorbates (O-H component) also contribute to the surface band bending, which lead the Fermi level pined at a level further closer to the conduction band edge on n-GaN surface. The n-GaN surface with lower surface band bending exhibits better linear electrical properties for Ti/GaN Ohmic contacts. Moreover, the density of positively charged surface states could be derived from the values of surface band bending.

Natural Frequncies of Coupled Blade-Bending and Shaft-Torsional Vibrations

Directory of Open Access Journals (Sweden)

B.O. Al-Bedoor

2007-01-01

Full Text Available In this study, the coupled shaft-torsional and blade-bending natural frequencies are investigated using a reduced order mathematical model. The system-coupled model is developed using the Lagrangian approach in conjunction with the assumed modes method to discretize the blade bending deflection. The model accounts for the blade stagger (setting angle, the system rotating speed and its induced stiffening effect. The coupled equations of motion are linearized based on the small deformation theory for the blade bending and shaft torsional deformation to enable calculation of the system natural frequencies for various combinations of system parameters. The obtained coupled eignvalue system is ready for use as a reference for comparison for larger size finite element simulations and for the use as a fast check on natural frequencies for the coupled blade bending and shaft torsional vibrations in the design and diagnostics processes. Some results on the predicted natural frequencies are graphically presented and discussed pertinent to the coupling controlling factors and their effects. In addition, the predicted coupled natural frequencies are validated using the Finite Element Commercial Package (Pro-Mechanica where good agreements are found.

Foam topology. Bending versus stretching dominated architectures

International Nuclear Information System (INIS)

Deshpande, V.; Ashby, M.; Fleck, N.

2000-01-01

Cellular solids can deform by either the bending or stretching of the cell walls. While most cellular solids are bending-dominated, those that are stretching-dominated are much more weight-efficient for structural applications. In this study we have investigated the topological criteria that dictate the deformation mechanism of a cellular solid by analysing the rigidity (or otherwise) of pin-jointed frameworks comprising inextensional struts. We show that the minimum node connectivity for a special class of lattice structured materials to be stretching-dominated is 6 for 2D foams and 12 for 3D foams. Similarly, sandwich plates comprising of truss cores faced with planar trusses require a minimum node connectivity of 9 to undergo stretching-dominated deformation for all loading states. (author)

Methods and tools for big data visualization

OpenAIRE

Zubova, Jelena; Kurasova, Olga

2015-01-01

In this paper, methods and tools for big data visualization have been investigated. Challenges faced by the big data analysis and visualization have been identified. Technologies for big data analysis have been discussed. A review of methods and tools for big data visualization has been done. Functionalities of the tools have been demonstrated by examples in order to highlight their advantages and disadvantages.

Development of three-dimensional pipe bending technology; Pipe zai no sanjigen mage kako gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, K; Takeda, S [Aisin Seiki Co. Ltd., Aichi (Japan)

1997-10-01

Recently, automotive parts uses move resin products or pipe-like products in order to achieve high quality or light weight. Additionally, the shape of automotive parts becomes more complicated. The rotary stretch bending method, although it is most popular method of bending a pipe, has some problems, such as a bending radius is limited due to use of bending mold, a thickness of an outer side of a bending portion is thinner, and a product is scratched easily during manufacturing. We have developed a three dimensional pipe bending process using a floating expanding plug and confirmed that this method can solve the above problems. 2 refs., 9 figs., 3 tabs.

NRC concerns about steam generator tube U-bend failures

International Nuclear Information System (INIS)

Dillon, R.L.

1981-01-01

This paper concerns itself with genralized NRC regulatory policy regarding SGT failures and staff reports and opinions which may tend to influence the developing policy specific to U-bend failures. The most significant analysis at hand in predicting NRC policy on SGT U-bend failures is Marsh's Evaluation of Steam Generator Tube Rupture Events. Marsh sets out to describe and analyze the five steam generator tube ruptures that are known to NRC. All have occurred in the period 1975 to 1980

Big data analytics methods and applications

CERN Document Server

Rao, BLS; Rao, SB

2016-01-01

This book has a collection of articles written by Big Data experts to describe some of the cutting-edge methods and applications from their respective areas of interest, and provides the reader with a detailed overview of the field of Big Data Analytics as it is practiced today. The chapters cover technical aspects of key areas that generate and use Big Data such as management and finance; medicine and healthcare; genome, cytome and microbiome; graphs and networks; Internet of Things; Big Data standards; bench-marking of systems; and others. In addition to different applications, key algorithmic approaches such as graph partitioning, clustering and finite mixture modelling of high-dimensional data are also covered. The varied collection of themes in this volume introduces the reader to the richness of the emerging field of Big Data Analytics.

The Big bang and the Quantum

Science.gov (United States)

Ashtekar, Abhay

2010-06-01

General relativity predicts that space-time comes to an end and physics comes to a halt at the big-bang. Recent developments in loop quantum cosmology have shown that these predictions cannot be trusted. Quantum geometry effects can resolve singularities, thereby opening new vistas. Examples are: The big bang is replaced by a quantum bounce; the `horizon problem' disappears; immediately after the big bounce, there is a super-inflationary phase with its own phenomenological ramifications; and, in presence of a standard inflation potential, initial conditions are naturally set for a long, slow roll inflation independently of what happens in the pre-big bang branch. As in my talk at the conference, I will first discuss the foundational issues and then the implications of the new Planck scale physics near the Big Bang.

Big Bang baryosynthesis

International Nuclear Information System (INIS)

Turner, M.S.; Chicago Univ., IL

1983-01-01

In these lectures I briefly review Big Bang baryosynthesis. In the first lecture I discuss the evidence which exists for the BAU, the failure of non-GUT symmetrical cosmologies, the qualitative picture of baryosynthesis, and numerical results of detailed baryosynthesis calculations. In the second lecture I discuss the requisite CP violation in some detail, further the statistical mechanics of baryosynthesis, possible complications to the simplest scenario, and one cosmological implication of Big Bang baryosynthesis. (orig./HSI)

Exploiting big data for critical care research.

Science.gov (United States)

Docherty, Annemarie B; Lone, Nazir I

2015-10-01

Over recent years the digitalization, collection and storage of vast quantities of data, in combination with advances in data science, has opened up a new era of big data. In this review, we define big data, identify examples of critical care research using big data, discuss the limitations and ethical concerns of using these large datasets and finally consider scope for future research. Big data refers to datasets whose size, complexity and dynamic nature are beyond the scope of traditional data collection and analysis methods. The potential benefits to critical care are significant, with faster progress in improving health and better value for money. Although not replacing clinical trials, big data can improve their design and advance the field of precision medicine. However, there are limitations to analysing big data using observational methods. In addition, there are ethical concerns regarding maintaining confidentiality of patients who contribute to these datasets. Big data have the potential to improve medical care and reduce costs, both by individualizing medicine, and bringing together multiple sources of data about individual patients. As big data become increasingly mainstream, it will be important to maintain public confidence by safeguarding data security, governance and confidentiality.

Empathy and the Big Five

OpenAIRE

Paulus, Christoph

2016-01-01

Del Barrio et al. (2004) haben vor mehr als 10 Jahren versucht, eine direkte Beziehung zwischen Empathie und den Big Five herzustellen. Im Mittel hatten in ihrer Stichprobe Frauen höhere Werte in der Empathie und auf den Big Five-Faktoren mit Ausnahme des Faktors Neurotizismus. Zusammenhänge zu Empathie fanden sie in den Bereichen Offenheit, Verträglichkeit, Gewissenhaftigkeit und Extraversion. In unseren Daten besitzen Frauen sowohl in der Empathie als auch den Big Five signifikant höhere We...

Measuring Public Acceptance of Nuclear Technology with Big data

Energy Technology Data Exchange (ETDEWEB)

Roh, Seugkook [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

Surveys can be conducted only on people in specific region and time interval, and it may be misleading to generalize the results to represent the attitude of the public. For example, opinions of a person living in metropolitan area, far from the dangers of nuclear reactors and enjoying cheap electricity produced by the reactors, and a person living in proximity of nuclear power plants, subject to tremendous damage should nuclear meltdown occur, certainly differs for the topic of nuclear generation. To conclude, big data is a useful tool to measure the public acceptance of nuclear technology efficiently (i.e., saves cost, time, and effort of measurement and analysis) and this research was able to provide a case for using big data to analyze public acceptance of nuclear technology. Finally, the analysis identified opinion leaders, which allows target-marketing when policy is executed.

Measuring Public Acceptance of Nuclear Technology with Big data

International Nuclear Information System (INIS)

Roh, Seugkook

2015-01-01

Surveys can be conducted only on people in specific region and time interval, and it may be misleading to generalize the results to represent the attitude of the public. For example, opinions of a person living in metropolitan area, far from the dangers of nuclear reactors and enjoying cheap electricity produced by the reactors, and a person living in proximity of nuclear power plants, subject to tremendous damage should nuclear meltdown occur, certainly differs for the topic of nuclear generation. To conclude, big data is a useful tool to measure the public acceptance of nuclear technology efficiently (i.e., saves cost, time, and effort of measurement and analysis) and this research was able to provide a case for using big data to analyze public acceptance of nuclear technology. Finally, the analysis identified opinion leaders, which allows target-marketing when policy is executed

Effects of large bending deflections on blade flutter limits

Energy Technology Data Exchange (ETDEWEB)

Kallesoee, Bjarne Skovmose; Hartvig Hansen, Morten

2008-04-15

The coupling of bending and torsion due to large blade bending are assumed to have some effects of the flutter limits of wind turbines. In the present report, the aeroelastic blade model suggested by Kallesoee, which is similar to a second order model, is used to investigate the aeroelastic stability limits of the RWT blade with and without the effects of the large blade deflection. The investigation shows no significant change of the flutter limit on the rotor speed due to the blade deflection,whereas the first edgewise bending mode becomes negatively damped due to the coupling with blade torsion which causes a change of the effective direction of blade vibration. These observations are confirmed by nonlinear aeroelastic simulations using HAWC2. This work is part of the UpWind project funded by the European Commission under the contract number SES6-CT-2005-019945 which is gratefully acknowledged. This report is the deliverable D2.3 of the UpWind project. (au)

TERAHERTZ SPECTROSCOPY AND GLOBAL ANALYSIS OF THE BENDING VIBRATIONS OF ACETYLENE 12C2D2

International Nuclear Information System (INIS)

Yu Shanshan; Drouin, Brian J.; Pearson, John C.; Pickett, Herbert M.; Lattanzi, Valerio; Walters, Adam

2009-01-01

Two hundred and fifty-one 12 C 2 D 2 transitions have been measured in the 0.2-1.6 THz region of its ν 5 -ν 4 difference band and 202 of them were observed for the first time. The accuracy of these measurements is estimated to be ranging from 50 kHz to 100 kHz. The 12 C 2 D 2 molecules were generated under room temperature by passing 120-150 mTorr D 2 O vapor through calcium carbide (CaC 2 ) powder. A multistate analysis was carried out for the bending vibrational modes ν 4 and ν 5 of 12 C 2 D 2 , which includes the lines observed in this work and prior microwave, far-infrared and infrared data on the pure bending levels. Significantly improved molecular parameters were obtained for 12 C 2 D 2 by adding the new measurements to the old data set, which had only 10 lines with microwave measurement precision. New frequency and intensity predictions have been made based on the obtained molecular parameters. The more precise measurements and new predictions reported here will support the analyses of astronomical observations by the future high-resolution spectroscopy telescopes such as Herschel, SOFIA, and ALMA, which will work in the terahertz spectral region.

The Impact of Bending Stress on the Performance of Giant Magneto-Impedance (GMI Magnetic Sensors

Directory of Open Access Journals (Sweden)

Julie Nabias

2017-03-01

Full Text Available The flexibility of amorphous Giant Magneto-Impedance (GMI micro wires makes them easy to use in several magnetic field sensing applications, such as electrical current sensing, where they need to be deformed in order to be aligned with the measured field. The present paper deals with the bending impact, as a parameter of influence of the sensor, on the GMI effect in 100 µm Co-rich amorphous wires. Changes in the values of key parameters associated with the GMI effect have been investigated under bending stress. These parameters included the GMI ratio, the intrinsic sensitivity, and the offset at a given bias field. The experimental results have shown that bending the wire resulted in a reduction of GMI ratio and sensitivity. The bending also induced a net change in the offset for the considered bending curvature and the set of used excitation parameters (1 MHz, 1 mA. Furthermore, the field of the maximum impedance, which is generally related to the anisotropy field of the wire, was increased. The reversibility and the repeatability of the bending effect were also evaluated by applying repetitive bending stresses. The observations have actually shown that the behavior of the wire under the bending stress was roughly reversible and repetitive.

Composite material bend-twist coupling for wind turbine blade applications

Science.gov (United States)

Walsh, Justin M.

Current efforts in wind turbine blade design seek to employ bend-twist coupling of composite materials for passive power control by twisting blades to feather. Past efforts in this area of study have proved to be problematic, especially in formulation of the bend-twist coupling coefficient alpha. Kevlar/epoxy, carbon/epoxy and glass/epoxy specimens were manufactured to study bend-twist coupling, from which numerical and analytical models could be verified. Finite element analysis was implemented to evaluate fiber orientation and material property effects on coupling magnitude. An analytical/empirical model was then derived to describe numerical results and serve as a replacement for the commonly used coupling coefficient alpha. Through the results from numerical and analytical models, a foundation for aeroelastic design of wind turbines blades utilizing biased composite materials is provided.

Erosion resistance of pipe bends with bio-inspired internal surfaces

Science.gov (United States)

Zhang, Chengchun; Matar, Omar

2013-11-01

Guided by the structure of a shell surface, a bio-inspired surface is proposed to enhance the erosion resistance of pipe bends carrying crude-oil and sand in the turbulent flow regime. A comparison of the erosion rate between a smooth bend and the bio-inspired one is carried out using numerical simulations: large eddy simulations are used to simulate turbulence, and these are coupled to a discrete element method for the solid particles. The results indicate that the bio-inspired surface can control effectively the liquid-solid flow near the wall, and decrease the particle-wall force. This, then, leads to a reduction in the erosion rate brought about by the sand transported by the crude-oil in the pipe bend. The China Scholarship Council is gratefully acknowledged.

Material development for grade X80 heavy-wall hot induction bends

International Nuclear Information System (INIS)

Wang Xu; Xiao Furen; Fu Yanhong; Chen Xiaowei; Liao Bo

2011-01-01

Highlights: ► The new material for X80 heavy wall thickness hot induction bend was designed. ► The continuous cooling transformation (CCT) diagrams were determined. ► The steel adapts to manufacture of X80 heavy-wall thickness hot induction bend. ► The optimum manufactural processes were obtained. ► The bending temperature is about 990 °C, and tempering is about 600 °C. - Abstract: A new steel for grade X80 heavy wall thickness hot induction bends was designed based on the chemical compositions of commercial X80 steels in this work. Then, its continuous cooling transformation (CCT) diagram was determined with Gleeble-3500 thermo-mechanical simulator. Furthermore, the effects of heat treatment technology on its microstructure and mechanical property were investigated, and the technology parameters of the heat treatment were optimized. The results show that the acicular ferrite and/or bainite transformations are promoted, the polygonal ferrite and pearlite transformation are restrained, because proper amount of alloying elements were added into the new steel. Therefore, the strength of this new steel is improved markedly, even if the cooling rate is lower, which ensure the higher strength distribution along cross section of the heavy wall thickness. It is significant for the manufacture of grade X80 heavy wall thickness hot induction bends in the second West-to-East gas transportation pipeline project of China.

Impact compressive and bending behaviour of rocks accompanied by electromagnetic phenomena.

Science.gov (United States)

Kobayashi, Hidetoshi; Horikawa, Keitaro; Ogawa, Kinya; Watanabe, Keiko

2014-08-28

It is well known that electromagnetic phenomena are often observed preceding earthquakes. However, the mechanism by which these electromagnetic waves are generated during the fracture and deformation of rocks has not been fully identified. Therefore, in order to examine the relationship between the electromagnetic phenomena and the mechanical properties of rocks, uniaxial compression and three-point bending tests for two kinds of rocks with different quartz content, granite and gabbro, have been carried out at quasi-static and dynamic rates. Especially, in the bending tests, pre-cracked specimens of granite were also tested. Using a split Hopkinson pressure bar and a ferrite-core antenna in close proximity to the specimens, both the stress-strain (load-displacement) curve and simultaneous electromagnetic wave magnitude were measured. It was found that the dynamic compressive and bending strengths and the stress increase slope of both rocks were higher than those observed in static tests; therefore, there is a strain-rate dependence in their strength and stress increase rate. It was found from the tests using the pre-cracked bending specimens that the intensity of electromagnetic waves measured during crack extension increased almost proportionally to the increase of the maximum stress intensity factor of specimens. This tendency was observed in both the dynamic and quasi-static three-point bending tests for granite. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

Modeling canopy-level productivity: is the "big-leaf" simplification acceptable?

Science.gov (United States)

Sprintsin, M.; Chen, J. M.

2009-05-01

The "big-leaf" approach to calculating the carbon balance of plant canopies assumes that canopy carbon fluxes have the same relative responses to the environment as any single unshaded leaf in the upper canopy. Widely used light use efficiency models are essentially simplified versions of the big-leaf model. Despite its wide acceptance, subsequent developments in the modeling of leaf photosynthesis and measurements of canopy physiology have brought into question the assumptions behind this approach showing that big leaf approximation is inadequate for simulating canopy photosynthesis because of the additional leaf internal control on carbon assimilation and because of the non-linear response of photosynthesis on leaf nitrogen and absorbed light, and changes in leaf microenvironment with canopy depth. To avoid this problem a sunlit/shaded leaf separation approach, within which the vegetation is treated as two big leaves under different illumination conditions, is gradually replacing the "big-leaf" strategy, for applications at local and regional scales. Such separation is now widely accepted as a more accurate and physiologically based approach for modeling canopy photosynthesis. Here we compare both strategies for Gross Primary Production (GPP) modeling using the Boreal Ecosystem Productivity Simulator (BEPS) at local (tower footprint) scale for different land cover types spread over North America: two broadleaf forests (Harvard, Massachusetts and Missouri Ozark, Missouri); two coniferous forests (Howland, Maine and Old Black Spruce, Saskatchewan); Lost Creek shrubland site (Wisconsin) and Mer Bleue petland (Ontario). BEPS calculates carbon fixation by scaling Farquhar's leaf biochemical model up to canopy level with stomatal conductance estimated by a modified version of the Ball-Woodrow-Berry model. The "big-leaf" approach was parameterized using derived leaf level parameters scaled up to canopy level by means of Leaf Area Index. The influence of sunlit

From God's particle to the world formula. Big Bang, Higgs, antimatter, and the mysterious shadow world

International Nuclear Information System (INIS)

Vaas, Ruediger

2013-01-01

Our knowledge about the elementary particles stands before a revolution: With the biggest machine of mankind the legendary Higgs boson was discovered - and for its prediction the Nobel prize awarded. Other researchers search for antiparticles from the universe and the shadow regime of the dark matter. What has be happened after the big bang? How the components of the universe have been arised? Of which consists the world - and why it exists at all? Science reporter and cosmology specialist Ruediger Vaas bends the bow from the smallest of all to the largest of all. He analyzes the actual state of knowledge and reports about the search for a ''world formula'', which explains, what holds the universe together in the innermost. A unique excursion to the fronts of research.

Pulsatile turbulent flow through pipe bends at high Dean and Womersley numbers

Science.gov (United States)

Kalpakli, Athanasia; Örlü, Ramis; Tillmark, Nils; Alfredsson, P. Henrik

2011-12-01

Turbulent pulsatile flows through pipe bends are prevalent in internal combustion engine components which consist of bent pipe sections and branching conduits. Nonetheless, most of the studies related to pulsatile flows in pipe bends focus on incompressible, low Womersley and low Dean number flows, primarily because they aim in modeling blood flow, while internal combustion engine related flows have mainly been addressed in terms of integral quantities and consist of single point measurements. The present study aims at bridging the gap between these two fields by means of time-resolved stereoscopic particle image velocimetry measurements in a pipe bend with conditions that are close to those encountered in exhaust manifolds. The time/phase-resolved three-dimensional cross-sectional flow-field 3 pipe diameters downstream the pipe bend is captured and the interplay between different secondary motions throughout a pulse cycle is discussed.

Pulsatile turbulent flow through pipe bends at high Dean and Womersley numbers

International Nuclear Information System (INIS)

Kalpakli, Athanasia; Örlü, Ramis; Tillmark, Nils; Alfredsson, P Henrik

2011-01-01

Turbulent pulsatile flows through pipe bends are prevalent in internal combustion engine components which consist of bent pipe sections and branching conduits. Nonetheless, most of the studies related to pulsatile flows in pipe bends focus on incompressible, low Womersley and low Dean number flows, primarily because they aim in modeling blood flow, while internal combustion engine related flows have mainly been addressed in terms of integral quantities and consist of single point measurements. The present study aims at bridging the gap between these two fields by means of time-resolved stereoscopic particle image velocimetry measurements in a pipe bend with conditions that are close to those encountered in exhaust manifolds. The time/phase-resolved three-dimensional cross-sectional flow-field 3 pipe diameters downstream the pipe bend is captured and the interplay between different secondary motions throughout a pulse cycle is discussed.

Demonstration model of LEP bending magnet

CERN Multimedia

CERN PhotoLab

1981-01-01

To save iron and raise the flux density, the LEP bending magnet laminations were separated by spacers and the space between the laminations was filled with concrete. This is a demonstration model, part of it with the spaced laminations only, the other part filled with concrete.

Performance of a novel VUV bending magnet beamline

CERN Document Server

Song, Y F; Hsieh, T F; Huang, L R; Chung, S C; Cheng, N F; Hsiung, G Y; Wang, D J; Chen, C T; Tsang, K L

2001-01-01

A novel high resolution, high flux bending magnet beamline with an energy range from 5 to 40 eV has been constructed at SRRC. This Dragon-like beamline, which horizontally collects 50 mrad of synchrotron radiation from a bending magnet source, uses four cylindrical gratings with an included angle of 140 deg. and a movable curved exit slit. The average photon flux with an energy resolving power of 1000 is about 2x10 sup 1 sup 2 photons/s, which is among the highest of all existing VUV bending magnet beamlines. An energy resolving power of 24,000 at 6.8 eV has been obtained from the Schumann-Runge bands (B sup 3 limit construction operator in a limit construction/sum L: summation operator operator End lower limit of a limit construction u lower limit End limit End sup - /leftarrow/gets A: =leftward arrow X sup 3 limit construction operator in a limit construction/sum L: summation operator operator End lower limit of a limit construction g lower limit End limit End sup -) absorption spectra of O sub 2 gas. A pho...

The application of Big Data in medicine: current implications and future directions.

Science.gov (United States)

Austin, Christopher; Kusumoto, Fred

2016-10-01

Since the mid 1980s, the world has experienced an unprecedented explosion in the capacity to produce, store, and communicate data, primarily in digital formats. Simultaneously, access to computing technologies in the form of the personal PC, smartphone, and other handheld devices has mirrored this growth. With these enhanced capabilities of data storage and rapid computation as well as real-time delivery of information via the internet, the average daily consumption of data by an individual has grown exponentially. Unbeknownst to many, Big Data has silently crept into our daily routines and, with continued development of cheap data storage and availability of smart devices both regionally and in developing countries, the influence of Big Data will continue to grow. This influence has also carried over to healthcare. This paper will provide an overview of Big Data, its benefits, potential pitfalls, and the projected impact on the future of medicine in general and cardiology in particular.

Effect of heat treatment on bend stress relaxation of pure tungsten

International Nuclear Information System (INIS)

Sasaki, Kenta; Nogami, Shuhei; Fukuda, Makoto; Katakai, Yasuyuki; Hasegawa, Akira

2013-01-01

Highlights: • Bend stress relaxation test was performed on the pure tungsten after heat treatment for stress relief. • The BSR ratio of the heat treated specimen was larger than that of the as-received specimen at this temperature region. • Small reduction in the BSR ratio was observed at the temperatures of 500–800 °C. • The BSR ratio of the heat treated specimen decreased significantly at the temperatures of 900–1000 °C. • The BSR ratio decreased significantly in a short time below 0.1 h, and then decreased slowly. -- Abstract: Bend stress relaxation (BSR) tests at temperatures of 500, 600, 800, 900 and 1000 °C for 0.1, 0.5 and 1 h in vacuum were performed on the pure tungsten after heat treatment for stress relief at 900 °C for 1 h. The degree of stress relaxation increased with test temperature. The BSR ratio of the heat treated specimen was larger than that of the as-received specimen at this temperature region. Small reduction in the BSR ratio was observed at the temperatures of 500, 600 and 800 °C. The BSR ratio of the heat treated specimen decreased significantly at the temperatures of 900 and 1000 °C and it was close to that of the as-received specimen. The BSR ratio of the heat treated specimen and the as-received specimen exhibited similar trend of time-evolution. The stress was exponentially relaxed with increasing test time. The BSR ratio decreased significantly in a short time below 0.1 h, and then decreased slowly. Higher activation energy of stress relaxation evaluated by cross-cut method was obtained for the higher temperature

Semantic Web Technologies and Big Data Infrastructures: SPARQL Federated Querying of Heterogeneous Big Data Stores

OpenAIRE

Konstantopoulos, Stasinos; Charalambidis, Angelos; Mouchakis, Giannis; Troumpoukis, Antonis; Jakobitsch, Jürgen; Karkaletsis, Vangelis

2016-01-01

The ability to cross-link large scale data with each other and with structured Semantic Web data, and the ability to uniformly process Semantic Web and other data adds value to both the Semantic Web and to the Big Data community. This paper presents work in progress towards integrating Big Data infrastructures with Semantic Web technologies, allowing for the cross-linking and uniform retrieval of data stored in both Big Data infrastructures and Semantic Web data. The technical challenges invo...

Quantum fields in a big-crunch-big-bang spacetime

International Nuclear Information System (INIS)

Tolley, Andrew J.; Turok, Neil

2002-01-01

We consider quantum field theory on a spacetime representing the big-crunch-big-bang transition postulated in ekpyrotic or cyclic cosmologies. We show via several independent methods that an essentially unique matching rule holds connecting the incoming state, in which a single extra dimension shrinks to zero, to the outgoing state in which it reexpands at the same rate. For free fields in our construction there is no particle production from the incoming adiabatic vacuum. When interactions are included the particle production for fixed external momentum is finite at the tree level. We discuss a formal correspondence between our construction and quantum field theory on de Sitter spacetime

Turning big bang into big bounce: II. Quantum dynamics

Energy Technology Data Exchange (ETDEWEB)

Malkiewicz, Przemyslaw; Piechocki, Wlodzimierz, E-mail: pmalk@fuw.edu.p, E-mail: piech@fuw.edu.p [Theoretical Physics Department, Institute for Nuclear Studies, Hoza 69, 00-681 Warsaw (Poland)

2010-11-21

We analyze the big bounce transition of the quantum Friedmann-Robertson-Walker model in the setting of the nonstandard loop quantum cosmology (LQC). Elementary observables are used to quantize composite observables. The spectrum of the energy density operator is bounded and continuous. The spectrum of the volume operator is bounded from below and discrete. It has equally distant levels defining a quantum of the volume. The discreteness may imply a foamy structure of spacetime at a semiclassical level which may be detected in astro-cosmo observations. The nonstandard LQC method has a free parameter that should be fixed in some way to specify the big bounce transition.

Scaling Big Data Cleansing

KAUST Repository

Khayyat, Zuhair

2017-07-31

Data cleansing approaches have usually focused on detecting and fixing errors with little attention to big data scaling. This presents a serious impediment since identify- ing and repairing dirty data often involves processing huge input datasets, handling sophisticated error discovery approaches and managing huge arbitrary errors. With large datasets, error detection becomes overly expensive and complicated especially when considering user-defined functions. Furthermore, a distinctive algorithm is de- sired to optimize inequality joins in sophisticated error discovery rather than na ̈ıvely parallelizing them. Also, when repairing large errors, their skewed distribution may obstruct effective error repairs. In this dissertation, I present solutions to overcome the above three problems in scaling data cleansing. First, I present BigDansing as a general system to tackle efficiency, scalability, and ease-of-use issues in data cleansing for Big Data. It automatically parallelizes the user’s code on top of general-purpose distributed platforms. Its programming inter- face allows users to express data quality rules independently from the requirements of parallel and distributed environments. Without sacrificing their quality, BigDans- ing also enables parallel execution of serial repair algorithms by exploiting the graph representation of discovered errors. The experimental results show that BigDansing outperforms existing baselines up to more than two orders of magnitude. Although BigDansing scales cleansing jobs, it still lacks the ability to handle sophisticated error discovery requiring inequality joins. Therefore, I developed IEJoin as an algorithm for fast inequality joins. It is based on sorted arrays and space efficient bit-arrays to reduce the problem’s search space. By comparing IEJoin against well- known optimizations, I show that it is more scalable, and several orders of magnitude faster. BigDansing depends on vertex-centric graph systems, i.e., Pregel

The ethics of big data in big agriculture

Directory of Open Access Journals (Sweden)

Isabelle M. Carbonell

2016-03-01

Full Text Available This paper examines the ethics of big data in agriculture, focusing on the power asymmetry between farmers and large agribusinesses like Monsanto. Following the recent purchase of Climate Corp., Monsanto is currently the most prominent biotech agribusiness to buy into big data. With wireless sensors on tractors monitoring or dictating every decision a farmer makes, Monsanto can now aggregate large quantities of previously proprietary farming data, enabling a privileged position with unique insights on a field-by-field basis into a third or more of the US farmland. This power asymmetry may be rebalanced through open-sourced data, and publicly-funded data analytic tools which rival Climate Corp. in complexity and innovation for use in the public domain.

Homogeneous and isotropic big rips?

CERN Document Server

Giovannini, Massimo

2005-01-01

We investigate the way big rips are approached in a fully inhomogeneous description of the space-time geometry. If the pressure and energy densities are connected by a (supernegative) barotropic index, the spatial gradients and the anisotropic expansion decay as the big rip is approached. This behaviour is contrasted with the usual big-bang singularities. A similar analysis is performed in the case of sudden (quiescent) singularities and it is argued that the spatial gradients may well be non-negligible in the vicinity of pressure singularities.

Rate Change Big Bang Theory

Science.gov (United States)

Strickland, Ken

2013-04-01

The Rate Change Big Bang Theory redefines the birth of the universe with a dramatic shift in energy direction and a new vision of the first moments. With rate change graph technology (RCGT) we can look back 13.7 billion years and experience every step of the big bang through geometrical intersection technology. The analysis of the Big Bang includes a visualization of the first objects, their properties, the astounding event that created space and time as well as a solution to the mystery of anti-matter.

Intelligent Test Mechanism Design of Worn Big Gear

Directory of Open Access Journals (Sweden)

Hong-Yu LIU

2014-10-01

Full Text Available With the continuous development of national economy, big gear was widely applied in metallurgy and mine domains. So, big gear plays an important role in above domains. In practical production, big gear abrasion and breach take place often. It affects normal production and causes unnecessary economic loss. A kind of intelligent test method was put forward on worn big gear mainly aimed at the big gear restriction conditions of high production cost, long production cycle and high- intensity artificial repair welding work. The measure equations transformations were made on involute straight gear. Original polar coordinate equations were transformed into rectangular coordinate equations. Big gear abrasion measure principle was introduced. Detection principle diagram was given. Detection route realization method was introduced. OADM12 laser sensor was selected. Detection on big gear abrasion area was realized by detection mechanism. Tested data of unworn gear and worn gear were led in designed calculation program written by Visual Basic language. Big gear abrasion quantity can be obtained. It provides a feasible method for intelligent test and intelligent repair welding on worn big gear.

[Big data in medicine and healthcare].

Science.gov (United States)

Rüping, Stefan

2015-08-01

Healthcare is one of the business fields with the highest Big Data potential. According to the prevailing definition, Big Data refers to the fact that data today is often too large and heterogeneous and changes too quickly to be stored, processed, and transformed into value by previous technologies. The technological trends drive Big Data: business processes are more and more executed electronically, consumers produce more and more data themselves - e.g. in social networks - and finally ever increasing digitalization. Currently, several new trends towards new data sources and innovative data analysis appear in medicine and healthcare. From the research perspective, omics-research is one clear Big Data topic. In practice, the electronic health records, free open data and the "quantified self" offer new perspectives for data analytics. Regarding analytics, significant advances have been made in the information extraction from text data, which unlocks a lot of data from clinical documentation for analytics purposes. At the same time, medicine and healthcare is lagging behind in the adoption of Big Data approaches. This can be traced to particular problems regarding data complexity and organizational, legal, and ethical challenges. The growing uptake of Big Data in general and first best-practice examples in medicine and healthcare in particular, indicate that innovative solutions will be coming. This paper gives an overview of the potentials of Big Data in medicine and healthcare.

From Big Data to Big Business

DEFF Research Database (Denmark)

Lund Pedersen, Carsten

2017-01-01

Idea in Brief: Problem: There is an enormous profit potential for manufacturing firms in big data, but one of the key barriers to obtaining data-driven growth is the lack of knowledge about which capabilities are needed to extract value and profit from data. Solution: We (BDBB research group at C...

The novel ethylene-responsive factor CsERF025 affects the development of fruit bending in cucumber.

Science.gov (United States)

Wang, Chunhua; Xin, Ming; Zhou, Xiuyan; Liu, Chunhong; Li, Shengnan; Liu, Dong; Xu, Yuan; Qin, Zhiwei

2017-11-01

Overexpression of CsERF025 induces fruit bending by promoting the production of ethylene. Cucumber fruit bending critically affects cucumber quality, but the mechanism that causes fruit bending remains unclear. To better understand this mechanism, we performed transcriptome analyses on tissues from the convex (C1) and concave (C2) sides of bending and straight (S) fruit at 2 days post anthesis (DPA). We identified a total of 281 differentially expressed genes (DEGs) from both the convex and concave sides of bent fruit that showed significantly different expression profiles relative to straight fruits. Of these 281 DEGs, 196 were up-regulated (C1/S_C2/S) and 85 were down-regulated (C1/S_C2/S). Among the 196 up-regulated DEGs, the transcriptional levels of genes related to ethylene biosynthesis and signaling pathways were significantly higher in bending fruit compared with straight fruit. CsERF025 showed the largest difference in expression between bending and straight fruit. CsERF025 is an AP2/ERF gene encoding a protein that localizes to the nucleus. Overexpression of this gene increased the bending rate of cucumber fruits and increased the angle of bending. CsERF025 increased both the expression of ethylene biosynthesis-related genes and the production of ethylene. The application of exogenous 1-aminocyclopropane-l-carboxylic acid (ACC) to straight fruits from control plants promoted fruit bending. Thus, CsERF025 enhances the production of ethylene and thereby promotes fruit bending in cucumber.

BIG SKY CARBON SEQUESTRATION PARTNERSHIP

Energy Technology Data Exchange (ETDEWEB)

Susan M. Capalbo

2004-06-01

The Big Sky Partnership, led by Montana State University, is comprised of research institutions, public entities and private sectors organizations, and the Confederated Salish and Kootenai Tribes and the Nez Perce Tribe. Efforts during the second performance period fall into four areas: evaluation of sources and carbon sequestration sinks; development of GIS-based reporting framework; designing an integrated suite of monitoring, measuring, and verification technologies; and initiating a comprehensive education and outreach program. At the first two Partnership meetings the groundwork was put in place to provide an assessment of capture and storage capabilities for CO{sub 2} utilizing the resources found in the Partnership region (both geological and terrestrial sinks), that would complement the ongoing DOE research. The region has a diverse array of geological formations that could provide storage options for carbon in one or more of its three states. Likewise, initial estimates of terrestrial sinks indicate a vast potential for increasing and maintaining soil C on forested, agricultural, and reclaimed lands. Both options include the potential for offsetting economic benefits to industry and society. Steps have been taken to assure that the GIS-based framework is consistent among types of sinks within the Big Sky Partnership area and with the efforts of other western DOE partnerships. Efforts are also being made to find funding to include Wyoming in the coverage areas for both geological and terrestrial sinks and sources. The Partnership recognizes the critical importance of measurement, monitoring, and verification technologies to support not only carbon trading but all policies and programs that DOE and other agencies may want to pursue in support of GHG mitigation. The efforts begun in developing and implementing MMV technologies for geological sequestration reflect this concern. Research is also underway to identify and validate best management practices for

Making big sense from big data in toxicology by read-across.

Science.gov (United States)

Hartung, Thomas

2016-01-01

Modern information technologies have made big data available in safety sciences, i.e., extremely large data sets that may be analyzed only computationally to reveal patterns, trends and associations. This happens by (1) compilation of large sets of existing data, e.g., as a result of the European REACH regulation, (2) the use of omics technologies and (3) systematic robotized testing in a high-throughput manner. All three approaches and some other high-content technologies leave us with big data--the challenge is now to make big sense of these data. Read-across, i.e., the local similarity-based intrapolation of properties, is gaining momentum with increasing data availability and consensus on how to process and report it. It is predominantly applied to in vivo test data as a gap-filling approach, but can similarly complement other incomplete datasets. Big data are first of all repositories for finding similar substances and ensure that the available data is fully exploited. High-content and high-throughput approaches similarly require focusing on clusters, in this case formed by underlying mechanisms such as pathways of toxicity. The closely connected properties, i.e., structural and biological similarity, create the confidence needed for predictions of toxic properties. Here, a new web-based tool under development called REACH-across, which aims to support and automate structure-based read-across, is presented among others.

[Big data in official statistics].

Science.gov (United States)

Zwick, Markus

2015-08-01

The concept of "big data" stands to change the face of official statistics over the coming years, having an impact on almost all aspects of data production. The tasks of future statisticians will not necessarily be to produce new data, but rather to identify and make use of existing data to adequately describe social and economic phenomena. Until big data can be used correctly in official statistics, a lot of questions need to be answered and problems solved: the quality of data, data protection, privacy, and the sustainable availability are some of the more pressing issues to be addressed. The essential skills of official statisticians will undoubtedly change, and this implies a number of challenges to be faced by statistical education systems, in universities, and inside the statistical offices. The national statistical offices of the European Union have concluded a concrete strategy for exploring the possibilities of big data for official statistics, by means of the Big Data Roadmap and Action Plan 1.0. This is an important first step and will have a significant influence on implementing the concept of big data inside the statistical offices of Germany.

Frequent arousals from winter torpor in Rafinesque's big-eared bat (Corynorhinus rafinesquii).