Remote Laboratory Collaboration Plan in Communications Engineering

Directory of Open Access Journals (Sweden)

Akram Ahmad Abu-aisheh

2012-11-01

Full Text Available Communications laboratories for electrical engineering undergraduates typically require that students perform practical experiments and document findings as part of their knowledge and skills development. Laboratory experiments are usally designed to support and reinforce theories presented in the classroom and foster independent thinking; however, the capital cost of equipment needed to sustain a viable laboratory environment is large and ongoing maintenance is an annual expense. Consequently, there is a need to identify and validate more economic solutions for engineering laboratories. This paper presents a remote laboratory collaboration plan for use in an elctrical engineering communications course.

Small-Engine Research Laboratory (SERL)

Data.gov (United States)

Federal Laboratory Consortium — Description: The Small-Engine Research Laboratory (SERL) is a facility designed to conduct experimental small-scale propulsion and power generation systems research....

Annotated bibliography of Software Engineering Laboratory literature

Science.gov (United States)

Morusiewicz, Linda; Valett, Jon D.

1991-01-01

An annotated bibliography of technical papers, documents, and memorandums produced by or related to the Software Engineering Laboratory is given. More than 100 publications are summarized. These publications cover many areas of software engineering and range from research reports to software documentation. All materials have been grouped into eight general subject areas for easy reference: The Software Engineering Laboratory; The Software Engineering Laboratory: Software Development Documents; Software Tools; Software Models; Software Measurement; Technology Evaluations; Ada Technology; and Data Collection. Subject and author indexes further classify these documents by specific topic and individual author.

Structures Laboratory | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Annotated bibliography of software engineering laboratory literature

Science.gov (United States)

Kistler, David; Bristow, John; Smith, Don

1994-01-01

This document is an annotated bibliography of technical papers, documents, and memorandums produced by or related to the Software Engineering Laboratory. Nearly 200 publications are summarized. These publications cover many areas of software engineering and range from research reports to software documentation. This document has been updated and reorganized substantially since the original version (SEL-82-006, November 1982). All materials have been grouped into eight general subject areas for easy reference: (1) The Software Engineering Laboratory; (2) The Software Engineering Laboratory: Software Development Documents; (3) Software Tools; (4) Software Models; (5) Software Measurement; (6) Technology Evaluations; (7) Ada Technology; and (8) Data Collection. This document contains an index of these publications classified by individual author.

Software Engineering Laboratory Series: Proceedings of the Twentieth Annual Software Engineering Workshop

Science.gov (United States)

1995-01-01

The Software Engineering Laboratory (SEL) is an organization sponsored by NASA/GSFC and created to investigate the effectiveness of software engineering technologies when applied to the development of application software. The activities, findings, and recommendations of the SEL are recorded in the Software Engineering Laboratory Series, a continuing series of reports that includes this document.

Systems Engineering Workshops | Wind | NREL

Science.gov (United States)

Workshops Systems Engineering Workshops The Wind Energy Systems Engineering Workshop is a biennial topics relevant to systems engineering and the wind industry. The presentations and agendas are available for all of the Systems Engineering Workshops: The 1st NREL Wind Energy Systems Engineering Workshop

MSI Biennial report 1988-1989

International Nuclear Information System (INIS)

Liotta, R.; Oppenheimer, E.

1990-01-01

This biennial report covers the years 1988 and 1989 and is the first one to carry the name of the Manne Siegbahn Institute of Physics, the official name of the institute since 1 July 1988. The CRYRING project, the new in-house accelerator storage ring for heavy, highly charged ions, is well under way and the summer of 1989 saw the starting of the installation of the dipole magnets. In November 1989 a final construction grant was given by the Wallenberg foundation. We expect that in the next biennial report the first physics results from this unique machine will be given. Apart from the CRYRING machine construction and the planning of experiments around it the research programme of the institute is a very vital one, as can be seen in this report

Fatigue behavior of wood-fiber-based tri-axial engineered sandwich composite panels (ESCP)

Science.gov (United States)

Jinghao Li; John F. Hunt; Shaoqin Gong; Zhiyong Cai

2015-01-01

The static and fatigue bending behavior of wood-fiber-based tri-axial engineered sandwich composite panels (ESCP) has been investigated by four-point bending tests. Fatigue panels and weakened panels (wESCP) with an initial interface defect were manufactured for the fatigue tests. Stress σ vs. number of cycles curves (S-N) were recorded under the different stress...

Software Engineering Laboratory Series: Proceedings of the Twenty-First Annual Software Engineering Workshop

Science.gov (United States)

1996-01-01

The Software Engineering Laboratory (SEL) is an organization sponsored by NASA/GSFC and created to investigate the effectiveness of software engineering technologies when applied to the development of application software. The activities, findings, and recommendations of the SEL are recorded in the Software Engineering Laboratory Series, a continuing series of reports that includes this document.

Software Engineering Laboratory Series: Proceedings of the Twenty-Second Annual Software Engineering Workshop

Science.gov (United States)

1997-01-01

The Software Engineering Laboratory (SEL) is an organization sponsored by NASA/GSFC and created to investigate the effectiveness of software engineering technologies when applied to the development of application software. The activities, findings, and recommendations of the SEL are recorded in the Software Engineering Laboratory Series, a continuing series of reports that includes this document.

Low-Cost Virtual Laboratory Workbench for Electronic Engineering

Science.gov (United States)

Achumba, Ifeyinwa E.; Azzi, Djamel; Stocker, James

2010-01-01

The laboratory component of undergraduate engineering education poses challenges in resource constrained engineering faculties. The cost, time, space and physical presence requirements of the traditional (real) laboratory approach are the contributory factors. These resource constraints may mitigate the acquisition of meaningful laboratory…

Cost estimate of grouting the proposed test pits at Idaho National Engineering Laboratory using the ORNL-recommended grouts

International Nuclear Information System (INIS)

Spence, R.D.

1987-08-01

EG and G Idaho will construct three experimental pits to simulate the TRU waste trenches at Idaho National Engineering Laboratory (INEL). Two of these pits will be grouted and then one will be destructively examined as soon as the grout cures and the other will be monitored for 10 years. Oak Ridge National Laboratory (ORNL) is evaluating grouts and will recommend a grout to EG and G Idaho to reduce the permeability of the pit, fill the large voids, and encapsulate the waste. A previous ORNL report (ORNL/TM-9881) discusses the grouts evaluated and the grout recommended based on those evaluations. This report evaluates the economics of grouting the experimental pits. The cost of double grouting two of the EG and G Idaho design pits at the Idaho National Engineering Laboratory using lance injection was estimated to be $100,000. Jet grouting the same two pits was estimated to cost $85,000. Both should be tried as part of the test EG and G Idaho is conducting

Joint 15. biennial conference of the West African Science Association and 19. biennial conference of Ghana Science Association: Book of abstracts

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

The publication contains abstracts of the joint fifteenth biennial conference of the West African Science Association and the nineteenth biennial conference of the Ghana Science Association,held at the University of Cape Coast,Ghana in September 1995. The theme of the conference was enhancing regional economic integration through science and technology`. A total of 180 abstracts have been presented either in english or french. Subject areas covered are:science education, social sciences, policy research, botany, zoology, agriculture, chemistry, biochemistry, physics, mathematics, computer science, geology, earth and medical sciences.

Joint 15. biennial conference of the West African Science Association and 19. biennial conference of Ghana Science Association: Book of abstracts

International Nuclear Information System (INIS)

1995-09-01

The publication contains abstracts of the joint fifteenth biennial conference of the West African Science Association and the nineteenth biennial conference of the Ghana Science Association,held at the University of Cape Coast,Ghana in September 1995. The theme of the conference was enhancing regional economic integration through science and technology'. A total of 180 abstracts have been presented either in english or french. Subject areas covered are:science education, social sciences, policy research, botany, zoology, agriculture, chemistry, biochemistry, physics, mathematics, computer science, geology, earth and medical sciences

Educational laboratory experiments on chemistry in a nuclear engineering school

International Nuclear Information System (INIS)

Akatsu, E.

1982-01-01

An educational laboratory experiment on radiochemistry was investigated by students in the general course of the Nuclear Engineering School of Japan Atomic Energy Research Institute. Most of them are not chemical engineers, but electrical and mechanical engineers. Therefore, the educational experiment was designed for them by introducing a ''word experiment'' in the initial stage and by reducing the chemical procedure as far as possible. It began with calculations on a simple solvent extraction process-the ''word experiment''--followed by the chemical separation of 144 Pr from 144 Ce with tri-n-butyl phosphate in a nitric acid system and then measurement of the radioactive decay and growth of the separated 144 Pr and 144 Ce, respectively. The chemical procedure was explained by the phenomenon but not by the mechanism of chelation. Most students thought the experiment was an exercise in solvent extraction or radiochemical separation rather than a radioactive equilibrium experiment. However, a pure chemist considered it as a sort of physical experiment, where the chemical procedure was used only for preparation of measuring samples. Another experiment, where 137 Cs was measured after isolation with ammonium phosphomolybdate, was also investigated. The experiment eliminated the need for students who were not chemists to know how to use radioactive tracers. These students appreciated the realization that they could understand the radioactivity in the environmental samples in a chemical frame of reference even though they were not chemists

The tropospheric biennial oscillation defined by a biennial mode of sea surface temperature and its impact on the atmospheric circulation and precipitation in the tropical eastern Indo-western Pacific region

Science.gov (United States)

Kim, Jinju; Kim, Kwang-Yul

2016-10-01

Temporal and spatial patterns of anomalous atmospheric circulation and precipitation over the Indo-Pacific region are analyzed in conjunction with the Tropospheric Biennial Oscillation as represented by the biennial mode of sea surface temperature anomalies (SSTA). The biennial components of key variables are identified independently of other variability via CSEOF analysis. Then, its impact on the Asian-Australian monsoon is examined. The biennial mode exhibits a seasonally distinctive atmospheric response over the tropical eastern Indo-western Pacific (EIWP) region (90°-150°E, 20°S-20°N). In boreal summer, local meridional circulation is a distinguishing characteristic over the tropical EIWP region, whereas a meridionally expanded branch of intensified zonal circulation develops in austral summer. Temporally varying evolution and distinct timing of SSTA phase transition in the Indian and Pacific Oceans is considered a main factor for this variation of circulation in the tropical EIWP region. The impact of the biennial mode is not the same between the two seasons, with different impacts over ocean areas in Asian monsoon and Australian monsoon regions.

Exposure to tri-o-cresyl phosphate detected in jet airplane passengers

International Nuclear Information System (INIS)

Liyasova, Mariya; Li, Bin; Schopfer, Lawrence M.; Nachon, Florian; Masson, Patrick; Furlong, Clement E.; Lockridge, Oksana

2011-01-01

The aircraft cabin and flight deck ventilation are supplied from partially compressed unfiltered bleed air directly from the engine. Worn or defective engine seals can result in the release of engine oil into the cabin air supply. Aircrew and passengers have complained of illness following such “fume events”. Adverse health effects are hypothesized to result from exposure to tricresyl phosphate mixed esters, a chemical added to jet engine oil and hydraulic fluid for its anti-wear properties. Our goal was to develop a laboratory test for exposure to tricresyl phosphate. The assay was based on the fact that the active-site serine of butyrylcholinesterase reacts with the active metabolite of tri-o-cresyl phosphate, cresyl saligenin phosphate, to make a stable phosphorylated adduct with an added mass of 80 Da. No other organophosphorus agent makes this adduct in vivo on butyrylcholinesterase. Blood samples from jet airplane passengers were obtained 24–48 h after completing a flight. Butyrylcholinesterase was partially purified from 25 ml serum or plasma, digested with pepsin, enriched for phosphorylated peptides by binding to titanium oxide, and analyzed by mass spectrometry. Of 12 jet airplane passengers tested, 6 were positive for exposure to tri-o-cresyl phosphate that is, they had detectable amounts of the phosphorylated peptide FGEpSAGAAS. The level of exposure was very low. No more than 0.05 to 3% of plasma butyrylcholinesterase was modified. None of the subjects had toxic symptoms. Four of the positive subjects were retested 3 to 7 months following their last airplane trip and were found to be negative for phosphorylated butyrylcholinesterase. In conclusion, this is the first report of an assay that detects exposure to tri-o-cresyl phosphate in jet airplane travelers. -- Highlights: ► Travel on jet airplanes is associated with an illness, aerotoxic syndrome. ► A possible cause is exposure to tricresyl phosphate in engine lubricating oil. ► A blood

Exposure to tri-o-cresyl phosphate detected in jet airplane passengers

Energy Technology Data Exchange (ETDEWEB)

Liyasova, Mariya, E-mail: mliyasov@unmc.edu [Eppley Institute, University of Nebraska Medical Center, Omaha, NE 68198-5950 (United States); Department of Environmental, Agricultural, and Occupational Health, University of Nebraska Medical Center, Omaha, NE (United States); Li, Bin, E-mail: binli@unmc.edu [Eppley Institute, University of Nebraska Medical Center, Omaha, NE 68198-5950 (United States); Schopfer, Lawrence M., E-mail: lmschopf@unmc.edu [Eppley Institute, University of Nebraska Medical Center, Omaha, NE 68198-5950 (United States); Nachon, Florian, E-mail: fnachon@nachon.net [Departement de Toxicologie, Institut de Recherche Biomedicale des Armees, 24 avenue des Marquis du Gresivaudan, 38702 La Tronche (France); Masson, Patrick, E-mail: pmasson@unmc.edu [Departement de Toxicologie, Institut de Recherche Biomedicale des Armees, 24 avenue des Marquis du Gresivaudan, 38702 La Tronche (France); Eppley Institute, University of Nebraska Medical Center, Omaha, NE 68198-5950 (United States); Furlong, Clement E., E-mail: clem@uw.edu [Department of Medicine (Div. Medical Genetics) and Genome Sciences, University of Washington, Seattle, WA 98195 (United States); Lockridge, Oksana, E-mail: olockrid@unmc.edu [Eppley Institute, University of Nebraska Medical Center, Omaha, NE 68198-5950 (United States); Department of Environmental, Agricultural, and Occupational Health, University of Nebraska Medical Center, Omaha, NE (United States)

2011-11-15

The aircraft cabin and flight deck ventilation are supplied from partially compressed unfiltered bleed air directly from the engine. Worn or defective engine seals can result in the release of engine oil into the cabin air supply. Aircrew and passengers have complained of illness following such 'fume events'. Adverse health effects are hypothesized to result from exposure to tricresyl phosphate mixed esters, a chemical added to jet engine oil and hydraulic fluid for its anti-wear properties. Our goal was to develop a laboratory test for exposure to tricresyl phosphate. The assay was based on the fact that the active-site serine of butyrylcholinesterase reacts with the active metabolite of tri-o-cresyl phosphate, cresyl saligenin phosphate, to make a stable phosphorylated adduct with an added mass of 80 Da. No other organophosphorus agent makes this adduct in vivo on butyrylcholinesterase. Blood samples from jet airplane passengers were obtained 24-48 h after completing a flight. Butyrylcholinesterase was partially purified from 25 ml serum or plasma, digested with pepsin, enriched for phosphorylated peptides by binding to titanium oxide, and analyzed by mass spectrometry. Of 12 jet airplane passengers tested, 6 were positive for exposure to tri-o-cresyl phosphate that is, they had detectable amounts of the phosphorylated peptide FGEpSAGAAS. The level of exposure was very low. No more than 0.05 to 3% of plasma butyrylcholinesterase was modified. None of the subjects had toxic symptoms. Four of the positive subjects were retested 3 to 7 months following their last airplane trip and were found to be negative for phosphorylated butyrylcholinesterase. In conclusion, this is the first report of an assay that detects exposure to tri-o-cresyl phosphate in jet airplane travelers. -- Highlights: Black-Right-Pointing-Pointer Travel on jet airplanes is associated with an illness, aerotoxic syndrome. Black-Right-Pointing-Pointer A possible cause is exposure to

Replacement of the Idaho National Engineering Laboratory Health Physics Instrumentation Laboratory

International Nuclear Information System (INIS)

1995-05-01

The DOE-Idaho Operations Office (DOE-ID) has prepared an environmental assessment (EA) on the replacement of the Idaho National Engineering Laboratory Health Physics Instrumentation Laboratory at the Idaho National Engineering Laboratory (INEL). The purpose of this project is to replace the existing Health Physics Instrumentation Laboratory (HPIL) with a new facility to provide a safe environment for maintaining and calibrating radiation detection instruments used at the Idaho National Engineering Laboratory. The existing HPIL facility provides portable health physics monitoring instrumentation and direct reading dosimetry procurement, maintenance and calibration of radiation detection instruments, and research and development support-services to the INEL and others. However, the existing facility was not originally designed for laboratory activities and does not provide an adequate, safe environment for calibration activities. The EA examined the potential environmental impacts of the proposed action and evaluated reasonable alternatives, including the no action alternative in accordance with the Council on Environmental Quality (CEQ) Regulations (40 CFR Parts 1500-1508). Based on the environmental analysis in the attached EA, the proposed action will not have a significant effect on the human environment within the meaning of the National Environmental Policy Act (NEPA) and 40 CFR Parts 1508.18 and 1508.27. The selected action (the proposed alternative) is composed of the following elements, each described or evaluated in the attached EA on the pages referenced. The proposed action is expected to begin in 1997 and will be completed within three years: design and construction of a new facility at the Central Facility Area of the INEL; operation of the facility, including instrument receipt, inspections and repairs, precision testing and calibration, and storage and issuance. The selected action will result in no significant environmental impacts

Remote Laboratory Collaboration Plan in Communications Engineering

OpenAIRE

Akram Ahmad Abu-aisheh; Tom Eppes

2012-01-01

Communications laboratories for electrical engineering undergraduates typically require that students perform practical experiments and document findings as part of their knowledge and skills development. Laboratory experiments are usally designed to support and reinforce theories presented in the classroom and foster independent thinking; however, the capital cost of equipment needed to sustain a viable laboratory environment is large and ongoing maintenance is an annual expense. Consequentl...

Sandia Laboratories technical capabilities: engineering analysis

International Nuclear Information System (INIS)

Lundergan, C.D.

1975-12-01

This report characterizes the engineering analysis capabilities at Sandia Laboratories. Selected applications of these capabilities are presented to illustrate the extent to which they can be applied in research and development programs

International Laboratory of Marine Radioactivity: Biennial report 1985-1986

International Nuclear Information System (INIS)

1987-10-01

A review of the scientific activities of the ILMR in 1985-1986 is presented. The scientific programs of the Radiobiology Laboratory, Radiochemistry-Geochemistry Laboratory and Marine Environmental Studies Laboratory are briefly described. In addition lists of the visiting consultants/experts, trainees/fellows, publications/meetings, Committee/Expert group membership, courses and research/technical contracts are given

Remote Laser Laboratory: Lifebuoy for Laser Engineering Curriculum

Directory of Open Access Journals (Sweden)

Igor Titov

2012-05-01

Full Text Available Laboratory experience is one of the essentials of engineering curriculum and even more so for laser engineering specialities. But such experience might be hazardous both for students and for expensive equipment. This paper presents a ready-to-use solution fitting great in both e-learning and safe remote operation paradigms: Remote Laser Laboratory (RLL. Software and hardware solutions are presented. In addition, a short description of ongoing student activities within the RLL framework is given.

National RCRA Hazardous Waste Biennial Report Data Files

Data.gov (United States)

U.S. Environmental Protection Agency — The United States Environmental Protection Agency (EPA), in cooperation with the States, biennially collects information regarding the generation, management, and...

78 FR 68061 - Wireline Competition Bureau Seeks Comment on the Lifeline Biennial Audit Plan

Science.gov (United States)

2013-11-13

... Seeks Comment on the Lifeline Biennial Audit Plan AGENCY: Federal Communications Commission. ACTION... for independent biennial audits of carriers drawing $5 million or more annually from the low-income program, by establishing uniform audit procedures [[Page 68062

Exposure to tri-o-cresyl phosphate detected in jet airplane passengers.

Science.gov (United States)

Liyasova, Mariya; Li, Bin; Schopfer, Lawrence M; Nachon, Florian; Masson, Patrick; Furlong, Clement E; Lockridge, Oksana

2011-11-01

The aircraft cabin and flight deck ventilation are supplied from partially compressed unfiltered bleed air directly from the engine. Worn or defective engine seals can result in the release of engine oil into the cabin air supply. Aircrew and passengers have complained of illness following such "fume events". Adverse health effects are hypothesized to result from exposure to tricresyl phosphate mixed esters, a chemical added to jet engine oil and hydraulic fluid for its anti-wear properties. Our goal was to develop a laboratory test for exposure to tricresyl phosphate. The assay was based on the fact that the active-site serine of butyrylcholinesterase reacts with the active metabolite of tri-o-cresyl phosphate, cresyl saligenin phosphate, to make a stable phosphorylated adduct with an added mass of 80 Da. No other organophosphorus agent makes this adduct in vivo on butyrylcholinesterase. Blood samples from jet airplane passengers were obtained 24-48 h after completing a flight. Butyrylcholinesterase was partially purified from 25 ml serum or plasma, digested with pepsin, enriched for phosphorylated peptides by binding to titanium oxide, and analyzed by mass spectrometry. Of 12 jet airplane passengers tested, 6 were positive for exposure to tri-o-cresyl phosphate that is, they had detectable amounts of the phosphorylated peptide FGEpSAGAAS. The level of exposure was very low. No more than 0.05 to 3% of plasma butyrylcholinesterase was modified. None of the subjects had toxic symptoms. Four of the positive subjects were retested 3 to 7 months following their last airplane trip and were found to be negative for phosphorylated butyrylcholinesterase. In conclusion, this is the first report of an assay that detects exposure to tri-o-cresyl phosphate in jet airplane travelers. Copyright © 2011 Elsevier Inc. All rights reserved.

Mini-projects in Chemical Engineering Laboratory

Directory of Open Access Journals (Sweden)

Angeles Cancela

2013-03-01

Full Text Available Chemical engineering laboratory practices based in mini-projects were design and applied the students of forestry engineering in chemical subject. This way of practice reveals a more cooperative learning and a different style of experimentation. The stated goal was to design practices that motivate students and to enable them to develop different skills, including cross teamwork and communication. This paper describes how these practices were developed and the advantages and disadvantages of using this methodology of teaching.

Ergonomic assessments of three Idaho National Engineering Laboratory cafeterias

Energy Technology Data Exchange (ETDEWEB)

Ostrom, L.T.; Romero, H.A.; Gilbert, B.G.; Wilhelmsen, C.A.

1993-01-01

The Idaho National Engineering Laboratory is a Department of Energy facility that performs a variety of engineering and research projects. EG G Idaho is the prime contractor for the laboratory and, as such, performs the support functions in addition to technical, research, and development functions. As a part of the EG G Idaho Industrial Hygiene Initiative, ergonomic assessments were conducted at three Idaho National Engineering Laboratory Cafeterias. The purposes of the assessments were to determine whether ergonomic problems existed in the work places and, if so, to make recommendations to improve the work place and task designs. The study showed there were ergonomic problems in all three cafeterias assessed. The primary ergonomic stresses observed included wrist and shoulder stress in the dish washing task, postural stress in the dish washing and food preparation tasks, and back stress in the food handling tasks.

Ergonomic assessments of three Idaho National Engineering Laboratory cafeterias

Energy Technology Data Exchange (ETDEWEB)

Ostrom, L.T.; Romero, H.A.; Gilbert, B.G.; Wilhelmsen, C.A.

1993-05-01

The Idaho National Engineering Laboratory is a Department of Energy facility that performs a variety of engineering and research projects. EG&G Idaho is the prime contractor for the laboratory and, as such, performs the support functions in addition to technical, research, and development functions. As a part of the EG&G Idaho Industrial Hygiene Initiative, ergonomic assessments were conducted at three Idaho National Engineering Laboratory Cafeterias. The purposes of the assessments were to determine whether ergonomic problems existed in the work places and, if so, to make recommendations to improve the work place and task designs. The study showed there were ergonomic problems in all three cafeterias assessed. The primary ergonomic stresses observed included wrist and shoulder stress in the dish washing task, postural stress in the dish washing and food preparation tasks, and back stress in the food handling tasks.

The biennial cycle of respiratory syncytial virus outbreaks in Croatia

Directory of Open Access Journals (Sweden)

Drazenovic Vladimir

2008-01-01

Full Text Available Abstract The paper analyses the epidemic pattern of respiratory syncytial virus (RSV outbreaks in children in Croatia. Over a period of 11 consecutive winter seasons (1994–2005 3,435 inpatients from Zagreb County aged from infancy to 10 years who were hospitalised with acute respiratory tract infections were tested for RSV-infection. RSV was identified in nasopharyngeal secretions of patients by virus isolation in cell culture and by detection of viral antigen with monoclonal antibodies. In the Zagreb area, RSV outbreaks were proven to vary in a two-year cycle, which was repeated every 23–25 months. This biennial cycle comprised one larger and one smaller season. Climate factors correlated significantly with the number of RSV cases identified only in the large seasons, which suggests that the biennial cycle is likely to continue regardless of meteorological conditions. Knowledge of this biennial pattern should be useful in predicting the onset of RSV outbreaks in Croatia, and would facilitate planning for the prevention and control of RSV infections in the region.

Project-Based Laboratory Experiences in Mechanical Engineering

Directory of Open Access Journals (Sweden)

Narendra Sharma

2011-12-01

Full Text Available In this paper we describe project-based laboratories in Mechanical Engineering designed to provide semester-long team experiences which mimic the real life industrial processes of design, development, testing and optimization. The labs are focused on courses at the sophomore level and thus require special attention to constraints of student backgrounds and experience. This paper describes laboratory projects in Dynamics and Fluid Mechanics.

Deep Underground Science and Engineering Laboratory - Preliminary Design Report

CERN Document Server

Lesko, Kevin T; Alonso, Jose; Bauer, Paul; Chan, Yuen-Dat; Chinowsky, William; Dangermond, Steve; Detwiler, Jason A; De Vries, Syd; DiGennaro, Richard; Exter, Elizabeth; Fernandez, Felix B; Freer, Elizabeth L; Gilchriese, Murdock G D; Goldschmidt, Azriel; Grammann, Ben; Griffing, William; Harlan, Bill; Haxton, Wick C; Headley, Michael; Heise, Jaret; Hladysz, Zbigniew; Jacobs, Dianna; Johnson, Michael; Kadel, Richard; Kaufman, Robert; King, Greg; Lanou, Robert; Lemut, Alberto; Ligeti, Zoltan; Marks, Steve; Martin, Ryan D; Matthesen, John; Matthew, Brendan; Matthews, Warren; McConnell, Randall; McElroy, William; Meyer, Deborah; Norris, Margaret; Plate, David; Robinson, Kem E; Roggenthen, William; Salve, Rohit; Sayler, Ben; Scheetz, John; Tarpinian, Jim; Taylor, David; Vardiman, David; Wheeler, Ron; Willhite, Joshua; Yeck, James

2011-01-01

The DUSEL Project has produced the Preliminary Design of the Deep Underground Science and Engineering Laboratory (DUSEL) at the rehabilitated former Homestake mine in South Dakota. The Facility design calls for, on the surface, two new buildings - one a visitor and education center, the other an experiment assembly hall - and multiple repurposed existing buildings. To support underground research activities, the design includes two laboratory modules and additional spaces at a level 4,850 feet underground for physics, biology, engineering, and Earth science experiments. On the same level, the design includes a Department of Energy-shepherded Large Cavity supporting the Long Baseline Neutrino Experiment. At the 7,400-feet level, the design incorporates one laboratory module and additional spaces for physics and Earth science efforts. With input from some 25 science and engineering collaborations, the Project has designed critical experimental space and infrastructure needs, including space for a suite of multi...

Enhanced biennial variability in the Pacific due to Atlantic capacitor effect.

Science.gov (United States)

Wang, Lei; Yu, Jin-Yi; Paek, Houk

2017-03-20

The El Niño-Southern Oscillation (ENSO) and the variability in the Pacific subtropical highs (PSHs) have major impacts on social and ecological systems. Here we present an Atlantic capacitor effect mechanism to suggest that the Atlantic is a key pacemaker of the biennial variability in the Pacific including that in ENSO and the PSHs during recent decades. The 'charging' (that is, ENSO imprinting the North Tropical Atlantic (NTA) sea surface temperature (SST) via an atmospheric bridge mechanism) and 'discharging' (that is, the NTA SST triggering the following ENSO via a subtropical teleconnection mechanism) processes alternate, generating the biennial rhythmic changes in the Pacific. Since the early 1990s, a warmer Atlantic due to the positive phase of Atlantic multidecadal oscillation and global warming trend has provided more favourable background state for the Atlantic capacitor effect, giving rise to enhanced biennial variability in the Pacific that may increase the occurrence frequency of severe natural hazard events.

Annual report of Nuclear Engineering Research Laboratory, Faculty of Engineering, University of Tokyo, fiscal year 1995

International Nuclear Information System (INIS)

1996-08-01

This is an annual report prepared on research education action, operation state of research instruments and others in FY 1995 at Nuclear Engineering Research Laboratory, Faculty of Engineering, University of Tokyo. The laboratory has four large instruments such as high speed neutron source reactor, 'Yayoi', electron linac, fundamentally experimental equipment for blanket design of nuclear fusion reactor, and heavy radiation research equipment (HIT), of which former two are used for cooperative research with universities in Japan, and the next blanket and the last HIT are also presented for cooperative researches in Faculty of Engineering and in University of Tokyo, respectively. FY 1995 was the beginning year of earnest discussion on future planning of this facility with concentrated effort. These four large research instruments are all in their active use. And, their further improvement is under preparation. In this report, the progress in FY 1995 on operation and management of the four large instruments are described at first, and on next, research actions, contents of theses for degree and graduation of students as well as research results of laboratory stuffs are summarized. These researches are constituted mainly using these large instruments in the facility, aiming at development of advanced and new field of atomic energy engineering and relates to nuclear reactor first wall engineering, nuclear reactor fuel cycle engineering, electromagnetic structure engineering, thermal-liquid engineering, mathematical information engineering, quantum beam engineering, new type reactor design and so on. (G.K.)

Annual report of Nuclear Engineering Research Laboratory, Faculty of Engineering, University of Tokyo, fiscal year 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-08-01

This is an annual report prepared on research education action, operation state of research instruments and others in FY 1995 at Nuclear Engineering Research Laboratory, Faculty of Engineering, University of Tokyo. The laboratory has four large instruments such as high speed neutron source reactor, `Yayoi`, electron linac, fundamentally experimental equipment for blanket design of nuclear fusion reactor, and heavy radiation research equipment (HIT), of which former two are used for cooperative research with universities in Japan, and the next blanket and the last HIT are also presented for cooperative researches in Faculty of Engineering and in University of Tokyo, respectively. FY 1995 was the beginning year of earnest discussion on future planning of this facility with concentrated effort. These four large research instruments are all in their active use. And, their further improvement is under preparation. In this report, the progress in FY 1995 on operation and management of the four large instruments are described at first, and on next, research actions, contents of theses for degree and graduation of students as well as research results of laboratory stuffs are summarized. These researches are constituted mainly using these large instruments in the facility, aiming at development of advanced and new field of atomic energy engineering and relates to nuclear reactor first wall engineering, nuclear reactor fuel cycle engineering, electromagnetic structure engineering, thermal-liquid engineering, mathematical information engineering, quantum beam engineering, new type reactor design and so on. (G.K.)

Geophysical Institute. Biennial report, 1993-1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-01-01

The 1993-1994 Geophysical Institute Biennial Report was published in November 1995 by the Geophysical Institute of the University of Alaska Fairbanks. It contains an overview of the Geophysical Institute, the Director`s Note, and research presentations concerning the following subjects: Scientific Predictions, Space Physics, Atmospheric Sciences, Snow, Ice and Permafrost, Tectonics and Sedimentation, Seismology, Volcanology, Remote Sensing, and other projects.

POLLUTION PREVENTION RESEARCH ONGOING - EPA'S RISK REDUCTION ENGINEERING LABORATORY

Science.gov (United States)

The mission of the Risk Reduction Engineering Laboratory is to advance the understanding, development and application of engineering solutions for the prevention or reduction of risks from environmental contamination. This mission is accomplished through basic and applied researc...

A woman like you: Women scientists and engineers at Brookhaven National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Benkovitz, Carmen; Bernholc, Nicole; Cohen, Anita; Eng, Susan; Enriquez-Leder, Rosario; Franz, Barbara; Gorden, Patricia; Hanson, Louise; Lamble, Geraldine; Martin, Harriet; Mastrangelo, Iris; McLane, Victoria; Villela, Maria-Alicia; Vivirito, Katherine; Woodhead, Avril

1991-01-01

This publication by the women in Science and Engineering introduces career possibilities in science and engineering. It introduces what work and home life are like for women who have already entered these fields. Women at Brookhaven National Laboratory work in a variety of challenging research roles -- from biologist and environmental scientist to safety engineer, from patent lawyer to technician. Brookhaven National Laboratory is a multi-program laboratory which carries out basic and applied research in the physical, biomedical and environmental sciences and in selected energy technologies. The Laboratory is managed by Associated University, Inc., under contract with the US Department of Energy. Brookhaven and the other national laboratories, because of their enormous research resources, can play a critical role in a education and training of the workforce.

GridSpace Engine of the ViroLab Virtual Laboratory

NARCIS (Netherlands)

Ciepiela, E.; Kocot, J.; Gubala, T.; Malawski, M.; Kasztelnik, M.; Bubak, M.; Bubak, M.; Turała, M.; Wiatr, K.

2008-01-01

GridSpace Engine is the central operational unit of the ViroLab Virtual Laboratory. This specific runtime environment enables access to computational and data resources by coordinating execution of experiments written in the Ruby programming language extended with virtual laboratory capabilities.

Nuclear Reactor Engineering Analysis Laboratory

International Nuclear Information System (INIS)

Carlos Chavez-Mercado; Jaime B. Morales-Sandoval; Benjamin E. Zayas-Perez

1998-01-01

The Nuclear Reactor Engineering Analysis Laboratory (NREAL) is a sophisticated computer system with state-of-the-art analytical tools and technology for analysis of light water reactors. Multiple application software tools can be activated to carry out different analyses and studies such as nuclear fuel reload evaluation, safety operation margin measurement, transient and severe accident analysis, nuclear reactor instability, operator training, normal and emergency procedures optimization, and human factors engineering studies. An advanced graphic interface, driven through touch-sensitive screens, provides the means to interact with specialized software and nuclear codes. The interface allows the visualization and control of all observable variables in a nuclear power plant (NPP), as well as a selected set of nonobservable or not directly controllable variables from conventional control panels

8. Biennial session on nuclear physics

International Nuclear Information System (INIS)

1985-01-01

In this biennial, some importance have been accorded deliberately to heavy ion experiment planning at very high energy and on results than can be waited for. Besides these collisions, different subjects are dealt with such as kaon scattering, hot nuclei, electron channeling photon and pion reactions in light nuclei, new forms of radioactivity, exotic nuclei, theoretical processing of nuclear dynamics, bag models, and pionic atoms [fr

Engineering Manhattan style: Sandia Laboratories as an example of postwar engineering

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

A great deal has been written about the history of science in America since World War II. Much of that work has explored the government`s research and development establishment, focusing on the scientific community immediately after the war. It is generally argued that the apparent triumphs of the huge and expensive wartime research and development projects gave rise to a belief that scientific resources should be nurtured and kept on hand - ready to provide service in an emergency. The Cold War drive for more and better weapons further fed this belief, leading to a massive system of national laboratories, military laboratories, and defense industries. The science of this complex is built on extensive financial support, the central strategy of which is that by steadily, and occasionally even lavishly funding large research programs, you will have a constant stream of scientific ideas that can be applied to national security purposes. What is true of science, is also true, in slightly modified form, of postwar engineering. The story I want to tell you today is, I think, an example of the way Cold War engineering r&d for national security worked. This report describes aspects of the Sandia National Laboratories.

A Profile of the Woman Engineer, 1984.

Science.gov (United States)

Hetrick, Haydee; And Others

This biennial report is based on responses from 2,112 of the 4,453 non-student members of the Society of Women Engineers (SWE) who were surveyed during the winter of 1983-84. All responses to the survey questionnaire (included in an appendix) were considered in the data analysis. Any woman with an engineering degree, holding state engineering…

Tri-State Synfuels Project Review: Volume 12. Fluor project status. [Proposed Henderson, Kentucky coal to gasoline plant; engineering

Energy Technology Data Exchange (ETDEWEB)

1982-06-01

The purpose of this report is to document and summarize activities associated with Fluor's efforts on the Tri-State Synfuels Project. The proposed facility was to be coal-to-transport fuels facility located in Henderson, Kentucky. Tri-State Synfuels Company was participating in the project as a partner of the US Department of Energy per terms of a Cooperative Agreement resulting from DOE's synfuel's program solicitation. Fluor's initial work plan called for preliminary engineering and procurement services to the point of commitment for construction for a Sasol Fischer-Tropsch plant. Work proceeded as planned until October 1981 when results of alternative coal-to-methanol studies revealed the economic disadvantage of the Synthol design for US markets. A number of alternative process studies followed to determine the best process configuration. In January 1982 Tri-State officially announced a change from Synthol to a Methanol to Gasoline (MTG) design basis. Further evaluation and cost estimates for the MTG facility eventually led to the conclusion that, given the depressed economic outlook for alternative fuels development, the project should be terminated. Official announcement of cancellation was made on April 13, 1982. At the time of project cancellation, Fluor had completed significant portions of the preliminary engineering effort. Included in this report are descriptions and summaries of Fluor's work during this project. In addition location of key project data and materials is identified and status reports for each operation are presented.

Tri-Cities Index of Innovation and Technology

Energy Technology Data Exchange (ETDEWEB)

Fowler, Richard A.; Scott, Michael J.; Butner, Ryan S.

2011-01-17

In 2001 and 2004, the Economic Development Office of Pacific Northwest National Laboratory published companion reports to the Washington Technology Center Index studies that provided additional information on the Tri-Cities (Kennewick-Richland-Pasco) area of the state, its technology businesses, and important advantages that the Tri-Cities have as places to live and do business. These reports also compared the Tri-Cities area to other technology-based metropolitan areas in the Pacific Northwest and nation along critical dimensions known to be important to technology firms. This report updates the material in these earlier reports, and highlights a growing Tri-Cities metropolitan area.

Development of the environmental management integrated baseline at the Idaho National Engineering Laboratory using systems engineering

International Nuclear Information System (INIS)

Murphy, J.A.; Caliva, R.M.; Wixson, J.R.

1997-01-01

The Idaho National Engineering Laboratory (INEL) is one of many Department of Energy (DOE) national laboratories that has been performing environmental cleanup and stabilization, which was accelerated upon the end of the cold war. In fact, the INEL currently receives two-thirds of its scope to perform these functions. However, the cleanup is a highly interactive system that creates an opportunity for systems engineering methodology to be employed. At the INEL, a group called EM (Environmental Management) Integration has been given this charter along with a small core of systems engineers. This paper discusses the progress to date of converting the INEL legacy system into one that uses the systems engineering discipline as the method to ensure that external requirements are met

New Laboratory Course for Senior-Level Chemical Engineering Students

Science.gov (United States)

Aronson, Mark T.; Deitcher, Robert W.; Xi, Yuanzhou; Davis, Robert J.

2009-01-01

A new laboratory course has been developed at the University of Virginia for senior- level chemical engineering students. The new course is based on three 4-week long experiments in bioprocess engineering, energy conversion and catalysis, and polymer synthesis and characterization. The emphasis is on the integration of process steps and the…

The biennial life strategy in a random environment

NARCIS (Netherlands)

Roerdink, J.B.T.M.

1988-01-01

A discrete-time population model with two age classes is studied which describes the growth of biennial plants in a randomly varying environment. A fraction of the oldest age class delays its flowering each year. The solution of the model involves products of random matrices. We calculate the exact

Tropospheric biennial oscillation and South Asian summer monsoon ...

Indian Academy of Sciences (India)

20

suggested that the Indo-Pacific SST displays strong impact on TBO as compared to .... and model display clear biennial signals with above 95% confidence level .... Ascending motion and low level convergence over the monsoon core ..... Indian and western Pacific oceans during the northern winter as revealed by a self-.

The quasi-biennial oscillation of 1.7 years in ground level enhancement events

Science.gov (United States)

Velasco Herrera, V. M.; Pérez-Peraza, J.; Soon, W.; Márquez-Adame, J. C.

2018-04-01

The so-called Ground Level Enhancement events are sporadic relativistic solar particles measured at ground level by a network of cosmic ray detectors worldwide. These sporadic events are typically assumed to occur by random chance. However, we find that by studying the last 56 ground level enhancement events reported from 1966 through 2014, these events occur preferentially in the positive phase of the quasi-biennial oscillation of 1.7 year periodicity. These discrete ground level enhancement events show that there is another type of solar emission (i.e., wavelike packets) that occurs only in a specific phase of a very particular oscillation. We interpret this empirical result to support that ground level enhancement events are not a result of purely stochastic processes. We used the Morlet wavelet to analyze the phase of each of the periodicities found by the wavelet analyses and local variations of power spectral density in these sporadic events. We found quasi-regular periodicities of 10.4, 6.55, 4.12, 2.9, 1.73, 0.86, 0.61, 0.4 and 0.24 years in ground level enhancements. Although some of these quasi-biennial oscillation periodicities (i.e., oscillations operating between 0.6 and 4 years) may be interpreted as simply harmonics and overtones of the fundamental solar cycle from the underlying sun-spot magnetism phenomenon. The sources of these periodicities are still unclear. Also there is no clear mechanism for the variability of the quasi-biennial oscillation periodicities itself. The quasi-biennial oscillation periodicities are broadly considered to be a variation of solar activity, associated with the solar dynamo process. Also, the intensity of these periodicities is more important around the years of maximum solar activity because the quasi-biennial oscillation periodicities are modulated by the solar cycle where the Sun is more energetically enhanced during activity maxima. To identify the relationships among ground level enhancement, solar, and cosmic

Combustion, performance, and selective catalytic reduction of NOx for a diesel engine operated with combined tri fuel (H_2, CH_4, and conventional diesel)

International Nuclear Information System (INIS)

Abu-Jrai, Ahmad M.; Al-Muhtaseb, Ala'a H.; Hasan, Ahmad O.

2017-01-01

In this study, the effect of tri fuel (ULSD, H_2, and CH_4) operation under real exhaust gas conditions with different gaseous fuel compositions on the combustion characteristics, engine emissions, and selective catalytic reduction (SCR) after treatment was examined at low, medium, and high engine loads. Pt/Al_2O_3-SCR reactor was used and operated at different exhaust gas temperatures. Results revealed that at low load, the two gaseous fuels (H_2 and CH_4) have the same trend on combustion proccess, where both reduce the in-cylinder pressure and rate of heat release. At the high engine load there was a considerable influence appeared as an increase of the premixed combustion phase and a significant decrease of the total combustion duration. In terms of emissions, it was observed that at high engine load, fuels with high CH_4 content tend to reduce NOx formation, whereas, fuels with high H_2 content tend to reduce PM formation, moreover, combustion of tri fuel with 50:50 fuel mixture resulted in lower BSFC compared to the other ratios and hence, the best engine efficiency. The hydrocarbon-SCR catalyst has shown satisfactory performance in NOx reduction under real diesel exhaust gas in a temperature window of 180–280 °C for all engine loads. - Highlights: • Effect of tri fuel (ULSD, H_2, CH_4) on combustion and engine emissions was examined. • Fuel with high CH_4 content (H50-M50 and H25-M75) tend to reduce NOx formation. • Fuel with high H_2 content (H75-M25 and H50-M50) tend to reduce PM formation. • Increasing the percentage of H_2 in the feed gas improved the NO_x reduction. • The hydrocarbon-SCR catalyst has shown satisfactory performance in NO_x reduction.

Upgrades of Hanford Engineering Development Laboratory hot cell facilities

International Nuclear Information System (INIS)

Daubert, R.L.; DesChane, D.J.

1987-01-01

The Hanford Engineering Development Laboratory operates the 327 Postirradiation Testing Laboratory (PITL) and the 324 Shielded Materials Facility (SMF). These hot cell facilities provide diverse capabilities for the postirradiation examination and testing of irradiated reactor fuels and materials. The primary function of these facilities is to determine failure mechanisms and effects of irradiation on physical and mechanical properties of reactor components. The purpose of this paper is to review major equipment and facility upgrades that enhance customer satisfaction and broaden the engineering capabilities for more diversified programs. These facility and system upgrades are providing higher quality remote nondestructive and destructive examination services with increased productivity, operator comfort, and customer satisfaction

Eighteenth annual risk reduction engineering laboratory research symposium

International Nuclear Information System (INIS)

Anon.

1992-01-01

The Eighteenth Annual Risk Reduction Engineering Laboratory Research Symposium was held in Cincinnati, Ohio, April 14-16, 1992. The purpose of this Symposium was to present the latest significant research findings from ongoing and recently completed projects funded by the Risk Reduction Engineering Laboratory (RREL). These Proceedings are organized into two sections. Sessions A and B, which contain extended abstracts of the paper presentations. A list of poster displays is also included. Subjects include remedial action, treatment, and control technologies for waste disposal, landfill liner and cover systems, underground storage tanks, and demonstration and development of innovative/alternative treatment technologies for hazardous waste. Alternative technology subjects include thermal destruction of hazardous wastes, field evaluations, existing treatment options, emerging treatment processes, waste minimization, and biosystems for hazardous waste destruction

Universities and national laboratory roles in nuclear engineering

International Nuclear Information System (INIS)

Sackett, J.I.

1991-01-01

Nuclear Engineering Education is being significantly challenged in the United States. The decline in enrollment generally and the reduction of the number of nuclear engineering departments has been well documented. These declines parallel a lack of new construction for nuclear power plants and a decline in research and development to support new plant design. Precisely at a time when innovation is is needed to deal with many issues facing nuclear power, the number of qualified people to do so is being reduced. It is important that the University and National Laboratory Communities cooperate to address these issues. The Universities must increasingly identify challenges facing nuclear power that demand innovative solutions and pursue them. To be drawn into the technology the best students must see a future, a need and identify challenges that they can meet. The University community can provide that vision with help from the National Laboratories. It has been a major goal within the reactor development program at Argonne National Laboratory to establish the kind of program that can help accomplish this

A Historical Analysis of the Biennial Budget Process

Science.gov (United States)

1988-04-01

commissioned In April 1974. He received a Master of Arts (MA) in Business Management from Tne University of The Philippines in 1983, and, in 1987, complitcd... tardiness there isn’t any empirical evidence to support this con- tention. To fully understand why biennial budgeting will not solve the first * three

Update on Engine Combustion Research at Sandia National Laboratories

International Nuclear Information System (INIS)

Jay Keller; Gurpreet Singh

2001-01-01

The objectives of this paper are to describe the research efforts in diesel engine combustion at Sandia National Laboratories' Combustion Research Facility and to provide recent experimental results. We have four diesel engine experiments supported by the Department of Energy, Office of Heavy Vehicle Technologies: a one-cylinder version of a Cummins heavy-duty engine, a diesel simulation facility, a one-cylinder Caterpillar engine to evaluate combustion of alternative fuels, and a homogeneous-charge, compression ignition (HCCI) engine. Recent experimental results of diesel combustion research will be discussed and a description will be given of our HCCI experimental program and of our HCCI modeling work

Full-participation of students with physical disabilities in science and engineering laboratories.

Science.gov (United States)

Jeannis, Hervens; Joseph, James; Goldberg, Mary; Seelman, Katherine; Schmeler, Mark; Cooper, Rory A

2018-02-01

To conduct a literature review identifying barriers and facilitators students with physical disabilities (SwD-P) may encounter in science and engineering (S&E) laboratories. Publications were identified from 1991 to 2015 in ERIC, web of science via web of knowledge, CINAHL, SCOPUS, IEEEXplore, engineering village, business source complete and PubMed databases using search terms and synonyms for accommodations, advanced manufacturing, additive manufacturing, assistive technology (AT), barriers, engineering, facilitators, instructor, laboratory, STEM education, science, students with disabilities and technology. Twenty-two of the 233 publications that met the review's inclusion criteria were examined. Barriers and facilitators were grouped based on the international classification of functioning, disability and health framework (ICF). None of the studies directly found barriers or facilitators to SwD-P in science or engineering laboratories within postsecondary environments. The literature is not clear on the issues specifically related to SwD-P. Given these findings, further research (e.g., surveys or interviews) should be conducted to identify more details to obtain more substantial information on the barriers that may prevent SwD-P from fully participating in S&E instructional laboratories. Implications for Rehabilitation Students with disabilities remain underrepresented going into STEM careers. A need exist to help uncover barriers students with disabilities encounter in STEM laboratory. Environments. Accommodations and strategies that facilitate participation in STEM laboratory environments are promising for students with disabilities.

Enhanced nutrient transport improves the depth-dependent properties of tri-layered engineered cartilage constructs with zonal co-culture of chondrocytes and MSCs.

Science.gov (United States)

Kim, Minwook; Farrell, Megan J; Steinberg, David R; Burdick, Jason A; Mauck, Robert L

2017-08-01

Biomimetic design in cartilage tissue engineering is a challenge given the complexity of the native tissue. While numerous studies have generated constructs with near-native bulk properties, recapitulating the depth-dependent features of native tissue remains a challenge. Furthermore, limitations in nutrient transport and matrix accumulation in engineered constructs hinders maturation within the central core of large constructs. To overcome these limitations, we fabricated tri-layered constructs that recapitulate the depth-dependent cellular organization and functional properties of native tissue using zonally derived chondrocytes co-cultured with MSCs. We also introduced porous hollow fibers (HFs) and HFs/cotton threads to enhance nutrient transport. Our results showed that tri-layered constructs with depth-dependent organization and properties could be fabricated. The addition of HFs or HFs/threads improved matrix accumulation in the central core region. With HF/threads, the local modulus in the deep region of tri-layered constructs nearly matched that of native tissue, though the properties in the central regions remained lower. These constructs reproduced the zonal organization and depth-dependent properties of native tissue, and demonstrate that a layer-by-layer fabrication scheme holds promise for the biomimetic repair of focal cartilage defects. Articular cartilage is a highly organized tissue driven by zonal heterogeneity of cells, extracellular matrix proteins and fibril orientations, resulting in depth-dependent mechanical properties. Therefore, the recapitulation of the functional properties of native cartilage in a tissue engineered construct requires such a biomimetic design of the morphological organization, and this has remained a challenge in cartilage tissue engineering. This study demonstrates that a layer-by-layer fabrication scheme, including co-cultures of zone-specific articular CHs and MSCs, can reproduce the depth-dependent characteristics

Contributions for the seventeenth biennial conference on carbon

International Nuclear Information System (INIS)

Delle, W.

1985-06-01

This report is the compilation of the papers prepared by KFA Juelich GmbH for the 17th Biennial Conference on Carbon. In the contributions, results are presented which were obtained from the application of carbon in the High Temperature Gas-Cooled Reactor and for the Spallation Neutron Source planned in the Federal Republic of Germany. (orig.) [de

12th Biennial International Conference on Baroque Music

Czech Academy of Sciences Publication Activity Database

Jonášová, Milada; Kapsa, Václav; Maňourová, L.

2007-01-01

Roč. 44, č. 1 (2007), s. 91-93 ISSN 0018-7003. [12th Biennial International Conference on Baroque Music . Varšava, 26.07.2006-30.07.2006] R&D Projects: GA AV ČR KJB800580502 Institutional research plan: CEZ:AV0Z90580513 Keywords : music * conference * baroque Subject RIV: AL - Art, Architecture, Cultural Heritage

Ninth Biennial Congress of the Association of Physicians

African Journals Online (AJOL)

4 Mei 1974 ... The 9th Biennial Congress of the Association of. Physicians of South Africa takes place on the campus of the University of Pretoria during the first week in July. There is every reason to expect that this will be a particularly interesting and im- portant congress and every effort is being made to ensure its ...

DFS-88, 1988 Tri-Service Data Fusion Symposium. Volume I - Technical Proceedings, Johns Hopkins University, Applied Physics Laboratory, Laurel, Maryland, 17 - 19 May 1988

National Research Council Canada - National Science Library

1988-01-01

The 1988 Tri-Service Data Fusion Symposium (DFS-88) was held at Laurel, Maryland on 17-19 May 1988 under the joint sponsorship of the Data Fusion Sub-Panel of the Joint Directors of Laboratories (JDL/DFSP...

An Undergraduate Nanotechnology Engineering Laboratory Course on Atomic Force Microscopy

Science.gov (United States)

Russo, D.; Fagan, R. D.; Hesjedal, T.

2011-01-01

The University of Waterloo, Waterloo, ON, Canada, is home to North America's first undergraduate program in nanotechnology. As part of the Nanotechnology Engineering degree program, a scanning probe microscopy (SPM)-based laboratory has been developed for students in their fourth year. The one-term laboratory course "Nanoprobing and…

A Low Cost Implementation of an Existing Hands-on Laboratory Experiment in Electronic Engineering

Directory of Open Access Journals (Sweden)

Clement Onime

2014-10-01

Full Text Available In engineering the pedagogical content of most formative programmes includes a significant amount of practical laboratory hands-on activity designed to deliver knowledge acquisition from actual experience alongside traditional face-to-face classroom based lectures and tutorials; this hands-on aspect is not always adequately addressed by current e-learning platforms. An innovative approach to e-learning in engineering, named computer aided engineering education (CAEE is about the use of computer aids for the enhanced, interactive delivery of educational materials in different fields of engineering through two separate but related components; one for classroom and another for practical hands-on laboratory work. The component for hands-on laboratory practical work focuses on the use of mixed reality (video-based augmented reality tools on mobile devices/platforms. This paper presents the computer aided engineering education (CAEE implementation of a laboratory experiment in micro-electronics that highlights some features such as the ability to closely implement an existing laboratory based hands-on experiment with lower associated costs and the ability to conduct the experiment off-line while maintaining existing pedagogical contents and standards.

Annual report of Nuclear Engineering Research Laboratory, University of Tokyo in fiscal 1991

International Nuclear Information System (INIS)

1992-07-01

In this annual report, the activities of education and research, the state of operation of research facilities and others in Nuclear Engineering Research Laboratory, University of Tokyo in fiscal year 1991 are summarized. In this Laboratory, there are four large research facilities, that is, the fast neutron source reactor 'Yayoi', the electron beam linac, the nuclear fusion reactor blanket experiment facility and the heavy irradiation research facility. Those are used for carrying out education and research in the wide fields of nuclear engineering, and are offered also for joint utilization. The results of the research by using respective research facilities were summarized in separate reports. In this annual report, the course of the management and operation of respective research facilities is described, and the research activities, the theses for doctorate and graduation theses of the teachers, personnel and graduate students in the Laboratory are summarized. In the research, those on first wall engineering for fusion reactors, fuel cycle engineering, electromagnetic structure engineering, AI and robotics, quantum beam engineering, new type reactor design and so on are included. (K.I.)

Biennial report of the Department of High Temperature Engineering

International Nuclear Information System (INIS)

1984-10-01

Research activities conducted in the Department of High Temperature Engineering during fiscal 1982 and 1983 are described. Research and development works of the department are mainly related to a multipurpose very high-temperature gas-cooled reactor (VHTR) and a fusion reactor. This report deals with the main results obtained on material test, heat transfer, fluid-dynamics, structural mechanics, development of computer codes and operation of an M + A (Mother and Adapter) section and a T 1 test section of the HENDEL (Helium Engineering Demonstration Loop). (author)

Robotic Manufacturing Science and Engineering Laboratory (RMSEL)

International Nuclear Information System (INIS)

1994-04-01

The Department of Energy (DOE) has prepared an environmental assessment (EA) on the proposed Robotic Manufacturing Science and Engineering Laboratory (RMSEL) at Sandia National Laboratories/New Mexico (SNL). This facility is needed to integrate, consolidate, and enhance the robotics research and testing currently in progress at SNL. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, an environmental impact statement is not required, and DOE is issuing this Finding of No Significant Impact (FONSI)

The DOE/NOAA meteorological program at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

George, D.H.

1996-01-01

The National Oceanic and Atmospheric Administration (NOAA) Air Resources Laboratory (ARL) has recently upgraded the U.S. Department of Energy's (DOE's) Idaho National Engineering Laboratory (INEL) Meteorological Measuring Network. This has allowed the entire service system to be modernized

Putting Reusability First: A Paradigm Switch in Remote Laboratories Engineering

Directory of Open Access Journals (Sweden)

Romain Vérot

2009-02-01

Full Text Available In this paper, we present a new devices brought online thanks to our Collaborative Remote Laboratories framework. Whereas previous devices integrated in our remote laboratory belongs to the domain of electronics, such as Vector Network Analyzers, the devices at the concern in this paper are, on one hand, an antenna workbench, and on the other, an homemade switching device, which embeds several electronic components. Because the middleware and framework for our environment were designed to be reusable, we wanted to put it to the test by integrating new and different devices in our Online Engineering catalog. After presenting the devices to be put online, we will expose the software development efforts required in regards to the reusability of the solution. As a consequence, the expose work and results tend to make the Online Engineering software architects to think reusability first, breaking with the current trends to implement Remote Labs one after the other, without much reusability, apart the capitalized experience. In this, we defend a paradigm switch in our current engineering approaches for Remote Laboratories implementations: Reusability should be thought first.

The Plant Genetic Engineering Laboratory For Desert Adaptation

Science.gov (United States)

Kemp, John D.; Phillips, Gregory C.

1985-11-01

The Plant Genetic Engineering Laboratory for Desert Adaptation (PGEL) is one of five Centers of Technical Excellence established as a part of the state of New Mexico's Rio Grande Research Corridor (RGRC). The scientific mission of PGEL is to bring innovative advances in plant biotechnology to bear on agricultural productivity in arid and semi-arid regions. Research activities focus on molecular and cellular genetics technology development in model systems, but also include stress physiology investigations and development of desert plant resources. PGEL interacts with the Los Alamos National Laboratory (LANL), a national laboratory participating in the RGRC. PGEL also has an economic development mission, which is being pursued through technology transfer activities to private companies and public agencies.

Women's Experiences in the Engineering Laboratory in Japan

Science.gov (United States)

Hosaka, Masako

2014-01-01

This qualitative study aims to examine Japanese women undergraduate engineering students' experiences of interacting with departmental peers of the same year in the laboratory setting by using interview data of 32 final-year students at two modestly selective national universities in Japan. Expectation state theory that explains unequal…

Annual report of Nuclear Engineering Research Laboratory, University of Tokyo in fiscal 1989

International Nuclear Information System (INIS)

1990-01-01

This report summerizes the research and educational activities at the Nuclear Engineering Research Laboratory, Faculty of Engineering, University of Tokyo. The Laboratory holds four main facilities, which are Yayoi reactor, an electron accelerator, fusion blanket research facility, and heavy ion irradiation research facility. And they are open to the researchers both inside and outside the University. The application of the facilities are described. The activities and achievements of the Laboratory staffs, and theses for graduate, master, and doctor degrees are also summerized. (J.P.N.)

Math and science education programs from the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

1991-01-01

This booklet reviews math and science education programs at the Idaho National Engineering Laboratory (INEL). The programs can be categorized into six groups: teacher programs; science laboratories for students; student programs; education outreach programs; INEL Public Affairs Office; and programs for college faculty and students

A woman like you: Women scientists and engineers at Brookhaven National Laboratory. Careers in action

Energy Technology Data Exchange (ETDEWEB)

1991-12-31

This publication by the women in Science and Engineering introduces career possibilities in science and engineering. It introduces what work and home life are like for women who have already entered these fields. Women at Brookhaven National Laboratory work in a variety of challenging research roles -- from biologist and environmental scientist to safety engineer, from patent lawyer to technician. Brookhaven National Laboratory is a multi-program laboratory which carries out basic and applied research in the physical, biomedical and environmental sciences and in selected energy technologies. The Laboratory is managed by Associated University, Inc., under contract with the US Department of Energy. Brookhaven and the other national laboratories, because of their enormous research resources, can play a critical role in a education and training of the workforce.

Idaho National Engineering Laboratory, Test Area North, Hangar 629 -- Photographs, written historical and descriptive data

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-31

The report describes the history of the Idaho National Engineering Laboratory`s Hangar 629. The hangar was built to test the possibility of linking jet engine technology with nuclear power. The history of the project is described along with the development and eventual abandonment of the Flight Engine Test hangar. The report contains historical photographs and architectural drawings.

Learning by Brewing: Beer Production Experiments in the Chemical Engineering Laboratory

Science.gov (United States)

Cerretani, Colin; Kelkile, Esayas; Landry, Alexandra

2017-01-01

We discuss the successful creation and implementation of a biotechnology track within the chemical engineering unit operations course. The track focuses on engineering principles relevant to brewing. Following laboratory modules investigating heat transfer processes and yeast fermentation kinetics, student groups design and implement a project to…

Nuclear Plant Analyzer development at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Laats, E.T.

1986-10-01

The Nuclear Plant Analyzer (NPA) is a state-of-the-art safety analysis and engineering tool being used to address key nuclear power plant safety issues. Under the sponsorship of the US Nuclear Regulatory Commission (NRC), the NPA has been developed to integrate the NRC's computerized reactor behavior simulation codes such as RELAP5, TRAC-BWR and TRAC-PWR, with well-developed computer color graphics programs and large repositories of reactor design and experimental data. An important feature of the NPA is the capability to allow an analyst to redirect a RELAP5 or TRAC calculation as it progresses through its simulated scenario. The analyst can have the same power plant control capabilities as the operator of an actual plant. The NPA resides on the dual Control Data Corporation Cyber 176 mainframe computers at the Idaho National Engineering Laboratory and Cray-1S computers at the Los Alamos National Laboratory (LANL) and Kirtland Air Force Weapons Laboratory (KAFWL)

Partnerships in cleanup at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Hula, G.A.

1995-01-01

Environmental Restoration activities at the Idaho National Engineering Laboratory (INEL) are currently being conducted under a Federal Facility Agreement and Consent Order (FFA/CO). The FFA/CO was signed by the US Department of Energy-Idaho Operations Office (DOE-ID), the Environmental Protection Agency-Region 10 (EPA), and the state of Idaho Department of Health and Welfare (IDHW) in December 1991. The INEL FFA/CO has been successfully implemented due to the coordination, integration and communication among the DOE-ID, IDHW and EPA Project and WAG Managers. Successful implementation of this Tri-party Agreement hinges on one key concept: ownership of the agreement, including the routine and unexpected problems and conflicting schedules typically associated with three separate agencies. Other factors, such as (1) open and frequent communication, (2) trust among all players, (3) ''giving'' in order to ''get,'' (4) clear, concise documentation surrounding key decisions during implementation and (5) little turnover among the implementers of the Agreement, i.e., good institutional knowledge, will enhance implementation of the Agreement, but without ownership, successful implementation of the agreement may be jeopardized. This sense of ownership, as well as a sound professional working relationship between the Project and WAG Managers from each agency, has resulted in avoidance of the need for invoking the formal ''dispute resolution'' process outlined in the INEL Agreement. This facilitates timely decision-making (10 Record of Decisions have been signed to date at the INEL) which has quickly progressed the program from an ''assessment'' phase to a ''cleanup'' phase

Annual report of Radiation Laboratory Department of Nuclear Engineering Faculty of Engineering, Kyoto University

International Nuclear Information System (INIS)

1993-07-01

This publication is the collection of the papers presented research activities of Radiation laboratory, Department of Nuclear Engineering, Kyoto University during the 1992 academic/fiscal year (April, 1992 - March, 1993). The 48 of the presented papers are indexed individually. (J.P.N.)

Working Together for Student Achievement. 6th Biennial Joint Report

Science.gov (United States)

Washington State Board of Education, 2016

2016-01-01

The Washington State Board of Education (SBE) and the Professional Educator Standards Board (PESB) submitted this 6th biennial joint report to the Governor, Legislative Education Committees, and Superintendent of Public Instruction. The report outlines the collaborative work of the Boards, highlights accomplishments, and provides goals and…

International Laboratory of Marine Radioactivity. Biennial report 1983-1984

International Nuclear Information System (INIS)

1986-06-01

The report contains the results of the scientific tasks carried out in 1983-1984 by the International Laboratory of Marine Radioactivity at Monaco. The methods development and analytical quality assurance for radionuclide measurements, studies for evaluating environmental impacts of radionuclide releases into the sea, contribution to international marine pollution monitoring and research including special missions are presented. The 47 papers are published in summary form

Tri-Service Center for Oral Health Studies (TSCOHS)

Data.gov (United States)

Federal Laboratory Consortium — The Tri-Service Center for Oral Health Studies (TSCOHS), a service of the Postgraduate Dental College, is chartered by the Department of Defense TRICARE Management...

Annual report of Nuclear Engineering Research Laboratory, University of Tokyo in fiscal 1990

International Nuclear Information System (INIS)

1991-01-01

In this annual report, the activities of research and education and the state of operation of the research facilities in this Laboratory in fiscal year 1990 are summarized. There are four large research facilities in this Laboratory, that is, the fast neutron source reactor 'Yayoi', the electron beam linear accelerator, the nuclear fusion reactor blanket experiment device and the heavy ion irradiation research facility. Those are used to execute research and education in the wide fields of atomic energy engineering, and put to the common utilization by universities in whole Japan. The results of the research with these facilities have been reported in the separate reports. The research aims at developing the most advanced and new fields in nuclear reactor engineering, and includes the engineering of the first wall and the fuel cycle for nuclear fusion reactors, electromagnetic structure engineering, AI and robotics, quantum beam engineering, the design of new type reactors, the basic process of radiochemistry and so on. The report on the course of the large scale facilities, research activities, the publication of research, education and the events in the Laboratory in the year are described. (K.I.)

Modeling study of the ionospheric responses to the quasi-biennial oscillations of the sun and stratosphere

Science.gov (United States)

Wang, Jack C.; Tsai-Lin, Rong; Chang, Loren C.; Wu, Qian; Lin, Charles C. H.; Yue, Jia

2018-06-01

The Quasi-biennial Oscillation (QBO) is a persistent oscillation in the zonal mean zonal winds of the low latitude middle atmosphere that is driven by breaking planetary and gravity waves with a period near two years. The atmospheric tides that dominate the dynamics of the mesosphere and lower thermosphere region (MLT, between heights of 70-120 km) are excited in the troposphere and stratosphere, and propagate through QBO-modulated zonal mean zonal wind fields. This allows the MLT tidal response to also be modulated by the QBO, with implications for ionospheric/thermospheric variability. Interannual oscillations in solar radiation can also directly drive the variations in the ionosphere with similar periodicities through the photoionization. Many studies have observed the connection between the solar activity and QBO signal in ionospheric features such as total electron content (TEC). In this research, we develop an empirical model to isolate stratospheric QBO-related tidal variability in the MLT diurnal and semidiurnal tides using values from assimilated TIMED satellite data. Migrating tidal fields corresponding to stratospheric QBO eastward and westward phases, as well as with the quasi-biennial variations in solar activity isolated by the Multi-dimensional Ensemble Empirical Mode Decomposition (MEEMD) analysis from Hilbert-Huang Transform (HHT), are then used to drive the NCAR Thermosphere-Ionosphere-Electrodynamics General Circulation Model (TIE-GCM). The numerical experiment results indicate that the ionospheric QBO is mainly driven by the solar quasi-biennial variations during the solar maximum, since the solar quasi-biennial variation amplitude is directly proportionate to the solar cycle. The ionospheric QBO in the model is sensitive to both the stratospheric QBO and solar quasi-biennial variations during the solar minimum, with solar effects still playing a stronger role.

Idaho National Engineering Laboratory decontamination and decommissioning summary

International Nuclear Information System (INIS)

Chapin, J.A.

1981-01-01

Topics covered concern the decontamination and decommissioning (D and D) work performed at the Idaho National Engineering Laboratory (INEL) during FY 1979 and include both operations and development projects. Briefly presented are the different types of D and D projects planned and the D and D projects completed. The problems encountered on these projects and the development program recommended are discussed

Data collection procedures for the Software Engineering Laboratory (SEL) database

Science.gov (United States)

Heller, Gerard; Valett, Jon; Wild, Mary

1992-01-01

This document is a guidebook to collecting software engineering data on software development and maintenance efforts, as practiced in the Software Engineering Laboratory (SEL). It supersedes the document entitled Data Collection Procedures for the Rehosted SEL Database, number SEL-87-008 in the SEL series, which was published in October 1987. It presents procedures to be followed on software development and maintenance projects in the Flight Dynamics Division (FDD) of Goddard Space Flight Center (GSFC) for collecting data in support of SEL software engineering research activities. These procedures include detailed instructions for the completion and submission of SEL data collection forms.

20 Years of the MENC Biennial Conference: A Content Analysis

Science.gov (United States)

Palkki, Joshua; Albert, Daniel J.; Hill, Stuart Chapman; Shaw, Ryan D.

2016-01-01

The purpose of this study was to investigate the content and intended audiences for educational sessions offered at MENC biennial conferences in order to illuminate trends and topics in professional development. The researchers performed a content analysis of each session (N?= 2,593) using program booklets from conferences between 1988 and 2008,…

IAEA Marine Environment Laboratory - Monaco: Biennial report 1989-1990

International Nuclear Information System (INIS)

1991-01-01

The report contains the results of the scientific tasks carried out in 1989-90 by the IAEA Marine Environment Laboratory in Monaco. The methods development and analytical quality assurance for radionuclide measurements, studies for evaluating environmental impacts of radionuclide releases into the sea, contribution to international marine pollution monitoring and research including special missions are presented. In addition, lists of the visiting consultants/experts, trainees/fellows, publications/meetings, committee/expert group membership, courses and research/technical contracts are given. Figs and tabs

Tri-Laboratory Linux Capacity Cluster 2007 SOW

Energy Technology Data Exchange (ETDEWEB)

Seager, M

2007-03-22

). However, given the growing need for 'capability' systems as well, the budget demands are extreme and new, more cost effective ways of fielding these systems must be developed. This Tri-Laboratory Linux Capacity Cluster (TLCC) procurement represents the ASC first investment vehicle in these capacity systems. It also represents a new strategy for quickly building, fielding and integrating many Linux clusters of various sizes into classified and unclassified production service through a concept of Scalable Units (SU). The programmatic objective is to dramatically reduce the overall Total Cost of Ownership (TCO) of these 'capacity' systems relative to the best practices in Linux Cluster deployments today. This objective only makes sense in the context of these systems quickly becoming very robust and useful production clusters under the crushing load that will be inflicted on them by the ASC and SSP scientific simulation capacity workload.

Tri-Laboratory Linux Capacity Cluster 2007 SOW

International Nuclear Information System (INIS)

Seager, M.

2007-01-01

well, the budget demands are extreme and new, more cost effective ways of fielding these systems must be developed. This Tri-Laboratory Linux Capacity Cluster (TLCC) procurement represents the ASC first investment vehicle in these capacity systems. It also represents a new strategy for quickly building, fielding and integrating many Linux clusters of various sizes into classified and unclassified production service through a concept of Scalable Units (SU). The programmatic objective is to dramatically reduce the overall Total Cost of Ownership (TCO) of these 'capacity' systems relative to the best practices in Linux Cluster deployments today. This objective only makes sense in the context of these systems quickly becoming very robust and useful production clusters under the crushing load that will be inflicted on them by the ASC and SSP scientific simulation capacity workload.

RF Anechoic Chambers, Tri-Service Research Laboratory

Data.gov (United States)

Federal Laboratory Consortium — In collaboration with the Navy, there are 12 RF Anechoic and static free exposure chambers located at TSRL. These chambers cover the majority of the RF spectrum and...

National RCRA Hazardous Waste Biennial Report Data Files

Science.gov (United States)

The United States Environmental Protection Agency (EPA), in cooperation with the States, biennially collects information regarding the generation, management, and final disposition of hazardous wastes regulated under the Resource Conservation and Recovery Act of 1976 (RCRA), as amended. Collection, validation and verification of the Biennial Report (BR) data is the responsibility of RCRA authorized states and EPA regions. EPA does not modify the data reported by the states or regions. Any questions regarding the information reported for a RCRA handler should be directed to the state agency or region responsible for the BR data collection. BR data are collected every other year (odd-numbered years) and submitted in the following year. The BR data are used to support regulatory activities and provide basic statistics and trend of hazardous waste generation and management. BR data is available to the public through 3 mechanisms. 1. The RCRAInfo website includes data collected from 2001 to present-day (https://rcrainfo.epa.gov/rcrainfoweb/action/main-menu/view). Users of the RCRAInfo website can run queries and output reports for different data collection years at this site. All BR data collected from 2001 to present-day is stored in RCRAInfo, and is accessible through this website. 2. An FTP site allows users to access BR data files collected from 1999 - present day (ftp://ftp.epa.gov/rcrainfodata/). Zip files are available for download directly from this

Institutional Plan, FY 1993--1998, Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

1993-01-01

This document presents the plans and goals of the Idaho National Engineering Laboratory for FY 1993--1998. Areas discussed in this document include: INEL strategic view; initiatives; scientific and technical programs; environmental, safety, and health management, technology transfer, science and math education, and community affairs; human resources; site and facilities; and resource projections

Experiential learning in control systems laboratories and engineering project management

Science.gov (United States)

Reck, Rebecca Marie

2015, a panel of 40 control systems faculty members, from a variety of institutions, completed a multi-round Delphi survey in order to bring them toward consensus on the common aspects of their laboratories. The following winter, 45 additional faculty members and practitioners from the control systems community completed a follow-up survey to gather feedback on the results of the Delphi survey. During the Delphi study, the panelists identified 15 laboratory objectives, 26 concepts, and 15 components that were common in their laboratories. Then in both the Delphi survey and follow-up survey each participant rated the importance of each of these items. While the average ratings differed slightly between the two groups, the order of each set of items was compared with two different tests and the order was found to be similar. Some of the common and important learning objectives include connecting theory to what is implemented and observed in the laboratory, designing controllers, and modeling and simulating systems. The most common component in both groups was Math-Works software. Some of the common concepts include block diagrams, stability, and PID control. Defining common aspects of undergraduate control systems laboratories enables common development, detailed comparisons, and simplified adaptation of equipment and experiments between campuses and programs. Throughout an undergraduate program in engineering, there are multiple opportunities for hands-on laboratory experiences that are related to course content. However, a similarly immersive experience for project management graduate students is harder to incorporate for all students in a course at once. This study explores an experiential learning opportunity for graduate students in engineering management or project management programs. The project management students enroll in a project management course. Undergraduate students interested in working on a project with a real customer enroll in a different projects

Fabrication and preliminary study of a biomimetic tri-layer tubular graft based on fibers and fiber yarns for vascular tissue engineering.

Science.gov (United States)

Wu, Tong; Zhang, Jialing; Wang, Yuanfei; Li, Dandan; Sun, Binbin; El-Hamshary, Hany; Yin, Meng; Mo, Xiumei

2018-01-01

Designing a biomimetic and functional tissue-engineered vascular graft has been urgently needed for repairing and regenerating defected vascular tissues. Utilizing a multi-layered vascular scaffold is commonly considered an effective way, because multi-layered scaffolds can easily simulate the structure and function of natural blood vessels. Herein, we developed a novel tri-layer tubular graft consisted of Poly(L-lactide-co-caprolactone)/collagen (PLCL/COL) fibers and Poly(lactide-co-glycolide)/silk fibroin (PLGA/SF) yarns via a three-step electrospinning method. The tri-layer vascular graft consisted of PLCL/COL aligned fibers in inner layer, PLGA/SF yarns in middle layer, and PLCL/COL random fibers in outer layer. Each layer possessed tensile mechanical strength and elongation, and the entire tubular structure provided tensile and compressive supports. Furthermore, the human umbilical vein endothelial cells (HUVECs) and smooth muscle cells (SMCs) proliferated well on the materials. Fluorescence staining images demonstrated that the axially aligned PLCL/COL fibers prearranged endothelium morphology in lumen and the circumferential oriented PLGA/SF yarns regulated SMCs organization along the single yarns. The outside PLCL/COL random fibers performed as the fixed layer to hold the entire tubular structure. The in vivo results showed that the tri-layer vascular graft supported cell infiltration, scaffold biodegradation and abundant collagen production after subcutaneous implantation for 10weeks, revealing the optimal biocompatibility and tissue regenerative capability of the tri-layer graft. Therefore, the specially designed tri-layer vascular graft will be beneficial to vascular reconstruction. Copyright © 2017. Published by Elsevier B.V.

Idaho National Engineering Laboratory site development plan

International Nuclear Information System (INIS)

1994-09-01

This plan briefly describes the 20-year outlook for the Idaho National Engineering Laboratory (INEL). Missions, workloads, worker populations, facilities, land, and other resources necessary to fulfill the 20-year site development vision for the INEL are addressed. In addition, the plan examines factors that could enhance or deter new or expanded missions at the INEL. And finally, the plan discusses specific site development issues facing the INEL, possible solutions, resources required to resolve these issues, and the anticipated impacts if these issues remain unresolved

Quasi-biennial modulation of solar neutrino flux: connections with solar activity

Science.gov (United States)

Vecchio, A.; Laurenza, M.; D'alessi, L.; Carbone, V.; Storini, M.

2011-12-01

A quasi-biennial periodicity has been recently found (Vecchio et al., 2010) in the solar neutrino flux, as detected at the Homestake experiment, as well as in the flux of solar energetic protons, by means of the Empirical Modes Decomposition technique. Moreover, both fluxes have been found to be significantly correlated at the quasi-biennial timescale, thus supporting the hypothesis of a connection between solar neutrinos and solar activity. The origin of this connection is investigated, by modeling how the standard Mikheyev-Smirnov-Wolfenstein (MSW) effect (the process for which the well-known neutrino flavor oscillations are modified in passing through the material) could be influenced by matter fluctuations. As proposed by Burgess et al., 2004, by introducing a background magnetic field in the helioseismic model, density fluctuations can be excited in the radiative zone by the resonance between helioseismic g-modes and Alfvén waves. In particular, with reasonable values of the background magnetic field (10-100 kG), the distance between resonant layers could be of the same order of neutrino oscillation length. We study the effect over this distance of a background magnetic field which is variable with a ~2 yr period, in agreement with typical variations of solar activity. Our findings suggest that the quasi-biennial modulation of the neutrino flux is theoretically possible as a consequence of the magnetic field variations in the solar interior. A. Vecchio, M. Laurenza, V. Carbone, M. Storini, The Astrophysical Journal Letters, 709, L1-L5 (2010). C. Burgess, N. S. Dzhalilov, T. I. Rashba, V., B.Semikoz, J. W. F. Valle, Mon. Not. R. Astron. Soc., 348, 609-624 (2004).

Idaho National Engineering Laboratory installation roadmap assumptions document

International Nuclear Information System (INIS)

1993-05-01

This document is a composite of roadmap assumptions developed for the Idaho National Engineering Laboratory (INEL) by the US Department of Energy Idaho Field Office and subcontractor personnel as a key element in the implementation of the Roadmap Methodology for the INEL Site. The development and identification of these assumptions in an important factor in planning basis development and establishes the planning baseline for all subsequent roadmap analysis at the INEL

Building an integrated nuclear engineering and nuclear science human resources pipeline at the Idaho National Engineering and Environmental Laboratory

International Nuclear Information System (INIS)

Sneed, A.; Sikorski, B.; Lineberry, M.; Jolly, J.

2004-01-01

Full text: In 2002, the US Department of Energy (US DOE) transferred sponsorship of the INEEL and ANL-W to the DOE Office of Nuclear Energy, Science and Technology and designated the INEEL and ANL-W as the nation's lead laboratories for nuclear reactor and nuclear fuel cycle research and development. This transfer acknowledged the laboratories' history, infrastructure, expertise and commitment to collaborate broadly in order to fulfill its assigned role as the nation's center for nuclear energy research and development. Key to this role is the availability of well-educated and trained nuclear engineers, professionals from other disciplines of engineering, nuclear scientists, and others with advanced degrees in supporting disciplines such as physics, chemistry, and math. In 2005 the INEEL and ANL-W will be combined into the Idaho National Laboratory (INL). One of US DOE's objectives for the INL will be for it to take a strong role in the revitalization of nuclear engineering and nuclear science education in the US. Responding to this objective for the INL and the national need to rejuvenate nuclear engineering and nuclear science research and education, ISU, University of Idaho (UI), Boise State University, the INEEL, and ANL-W are all supporting a new Institute of Nuclear Science and Engineering (INSE), initially proposed by and to be administered by ISU. The Institute will rely on the resources of both universities and the INL to create a US center for reactor and fuel cycle research to development and attract outstanding faculty and students to Idaho and to the INL. The Institute and other university based education development efforts represent only one component of a viable Human Resources Pipeline from university to leading edge laboratory researcher. Another critical component is the successful integration of new graduates into the laboratory research environment, the transfer of knowledge from senior researchers, and the development of these individuals into

Educational digital resource for data analysis of Civil Engineering laboratory tests

OpenAIRE

Gustavo Henrique Nalon; Paulo Sergio de Almeida Barbosa; Walcyr Duarte Nascimento

2018-01-01

This work aims to implement and evaluate an interactive educational software that helps Civil Engineering students to perform and analyze the calculations related to different Soil Mechanics laboratory tests. This experience consists of an attempt to incorporate information and communication technologies (ICTs) into the engineering teaching-learning process. The content of the program is distributed into three different modules: “Compaction test”, “Consolidation test”, and “Direct shear test”...

Quasi-biennial oscillations in the geomagnetic field: Their global characteristics and origin

DEFF Research Database (Denmark)

Ou, Jiaming; Du, Aimin; Finlay, Chris

2017-01-01

Quasi-biennial oscillations (QBOs), with periods in the range 1–3 years, have been persistently observed in the geomagnetic field. They provide unique information on the mechanisms by which magnetospheric and ionospheric current systems are modulated on interannual timescales and are also of cruc...... primarily originates from the current systems due to the solar wind-magnetosphere-ionosphere coupling process....... postmidnight sectors, and the results from spherical harmonic analysis, verify that the majority of geomagnetic QBO is of external origin. We furthermore find a very high correlation between the geomagnetic QBO and the QBOs in solar wind speed and solar wind dynamic pressure. This suggests the geomagnetic QBO......Quasi-biennial oscillations (QBOs), with periods in the range 1–3 years, have been persistently observed in the geomagnetic field. They provide unique information on the mechanisms by which magnetospheric and ionospheric current systems are modulated on interannual timescales and are also...

What's Happening in the Software Engineering Laboratory?

Science.gov (United States)

Pajerski, Rose; Green, Scott; Smith, Donald

1995-01-01

Since 1976 the Software Engineering Laboratory (SEL) has been dedicated to understanding and improving the way in which one NASA organization the Flight Dynamics Division (FDD) at Goddard Space Flight Center, develops, maintains, and manages complex flight dynamics systems. This paper presents an overview of recent activities and studies in SEL, using as a framework the SEL's organizational goals and experience based software improvement approach. It focuses on two SEL experience areas : (1) the evolution of the measurement program and (2) an analysis of three generations of Cleanroom experiments.

Educational digital resource for data analysis of Civil Engineering laboratory tests

Directory of Open Access Journals (Sweden)

Gustavo Henrique Nalon

2018-02-01

Full Text Available This work aims to implement and evaluate an interactive educational software that helps Civil Engineering students to perform and analyze the calculations related to different Soil Mechanics laboratory tests. This experience consists of an attempt to incorporate information and communication technologies (ICTs into the engineering teaching-learning process. The content of the program is distributed into three different modules: “Compaction test”, “Consolidation test”, and “Direct shear test”. Using vector graphics, tables, illustrative figures, animations, equations, tip buttons, and immediate correction of mistakes, the software clarifies the relationship between theoretical concepts and practical laboratory results, instructs the students in the moments of doubt, attracts their interest, and motivates them to achieve the complete data interpretation. Based on the results of an applied evaluation questionnaire, it was observed that most of the students were satisfied with the contents and functionalities of the program. The developed tool can be an inspiration for the creation of new educational software that improve the quality of education in different engineering areas.

Waste Isolation Pilot Plant Biennial Environmental Compliance Report

Energy Technology Data Exchange (ETDEWEB)

Washington Regulatory and Environmental Services (WRES)

2004-10-25

This Biennial Environmental Compliance Report (BECR) documents environmental regulatory compliance at the Waste Isolation Pilot Plant (WIPP), a facility designed and authorized for the safe disposal of transuranic (TRU) radioactive waste, for the reporting period of April 1, 2002, to March 31, 2004. As required by the WIPP Land Withdrawal Act (LWA) (Public Law [Pub. L.] 102-579, as amended by Pub. L. 104-201), the BECR documents U.S. Department of Energy (DOE) compliance with applicable environmental protection laws and regulations implemented by agencies of the federal government and the state of New Mexico.

Waste Isolation Pilot Plant Biennial Environmental Compliance Report

International Nuclear Information System (INIS)

2004-01-01

This Biennial Environmental Compliance Report (BECR) documents environmental regulatory compliance at the Waste Isolation Pilot Plant (WIPP), a facility designed and authorized for the safe disposal of transuranic (TRU) radioactive waste, for the reporting period of April 1, 2002, to March 31, 2004. As required by the WIPP Land Withdrawal Act (LWA) (Public Law [Pub. L.] 102-579, as amended by Pub. L. 104-201), the BECR documents U.S. Department of Energy (DOE) compliance with applicable environmental protection laws and regulations implemented by agencies of the federal government and the state of New Mexico.

Successful neural network projects at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Cordes, G.A.

1991-01-01

This paper presents recent and current projects at the Idaho National Engineering Laboratory (INEL) that research and apply neural network technology. The projects are summarized in the paper and their direct application to space reactor power and propulsion systems activities is discussed. 9 refs., 10 figs., 3 tabs

High-Performance Liquid Chromatography in the Undergraduate Chemical Engineering Laboratory

Science.gov (United States)

Frey, Douglas D.; Guo, Hui; Karnik, Nikhila

2013-01-01

This article describes the assembly of a simple, low-cost, high-performance liquid chromatography (HPLC) system and its use in the undergraduate chemical engineering laboratory course to perform simple experiments. By interpreting the results from these experiments students are able to gain significant experience in the general method of…

A High Intensity Multi-Purpose D-D Neutron Generator for Nuclear Engineering Laboratories

International Nuclear Information System (INIS)

Ka-Ngo Leung; Jasmina L. Vujic; Edward C. Morse; Per F. Peterson

2005-01-01

This NEER project involves the design, construction and testing of a low-cost high intensity D-D neutron generator for teaching nuclear engineering students in a laboratory environment without radioisotopes or a nuclear reactor. The neutron generator was designed, fabricated and tested at Lawrence Berkeley National Laboratory (LBNL)

Key Science and Engineering Indicators: 2010 Digest. NSB 10-02

Science.gov (United States)

Roesel, Cheryl, Ed.

2010-01-01

The National Science Board (Board) is required under the National Science Foundation (NSF) Act, 42 U.S.C. (United States Code) Section 1863 (j) (1) to prepare and transmit the biennial "Science and Engineering Indicators" ("SEI") report to the President and to the Congress by January 15 of every even-numbered year. The report…

New engine method for biodiesel cetane number testing

Directory of Open Access Journals (Sweden)

Pešić Radivoje B.

2008-01-01

Full Text Available Substitution of fossil fuels with fuels that come from part renewable sources has been a subject of many studies and researches in the past decade. Considering the higher cost and limits of production resources, a special attention is focused on raising the energy efficiency of biofuel usage, mainly through optimization of the combustion process. Consequently, in biofuel applications, there is a need for determination of auto-ignition quality expressed by cetane number as a dominant characteristic that influences combustion parameters. The fact that the method for cetane number determination is comparative in nature has led us to try to develop substitute engine method for cetane number determination, by the use of the available laboratory equipment and serial, mono-cylinder engine with direct injection, DMB LDA 450. Description of the method, results of optimization of engine’s working parameters for conduction of the test and method’s Accuracy estimation are given in the paper. The paper also presents the results of domestic biodiesel fuels cetane number testing with the application of described engine method, developed at the Laboratory for internal combustion engines and fuels and lubricants of the Faculty of Mechanical Engineering from Kragujevac, Serbia.

Stabilization of mixed waste at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Boehmer, A.M.; Gillins, R.L.; Larsen, M.M.

1989-01-01

EG and G Idaho, Inc. has initiated a program to develop safe, efficient, cost-effective treatment methods for the stabilization of some of the hazardous and mixed wastes generated at the Idaho National Engineering Laboratory. Laboratory-scale testing has shown that extraction procedure toxic wastes can be successfully stabilized by solidification, using various binders to produce nontoxic, stable waste forms for safe, long-term disposal as either landfill waste or low-level radioactive waste, depending upon the radioactivity content. This paper presents the results of drum-scale solidification testing conducted on hazardous, low-level incinerator flyash generated at the Waste Experimental Reduction Facility. The drum-scale test program was conducted to verify that laboratory-scale results could be successfully adapted into a production operation

Idaho National Engineering Laboratory waste area groups 1--7 and 10 Technology Logic Diagram

International Nuclear Information System (INIS)

O'Brien, M.C.; Meservey, R.H.; Little, M.; Ferguson, J.S.; Gilmore, M.C.

1993-09-01

The Technology Logic Diagram was developed to provide technical alternatives for environmental restoration projects at the Idaho National Engineering Laboratory. The diagram (three volumes) documents suggested solutions to the characterization, retrieval, and treatment phases of cleanup activities at contaminated sites within 8 of the laboratory's 10 waste area groups. Contaminated sites at the laboratory's Naval Reactor Facility and Argonne National Laboratory-West are not included in this diagram

A Three-Year Feedback Study of a Remote Laboratory Used in Control Engineering Studies

Science.gov (United States)

Chevalier, Amélie; Copot, Cosmin; Ionescu, Clara; De Keyser, Robin

2017-01-01

This paper discusses the results of a feedback study for a remote laboratory used in the education of control engineering students. The goal is to show the effectiveness of the remote laboratory on examination results. To provide an overview, the two applications of the remote laboratory are addressed: 1) the Stewart platform, and 2) the quadruple…

Annual report of Nuclear Engineering Research Laboratory, University of Tokyo in fiscal 1992

International Nuclear Information System (INIS)

1993-07-01

In this annual report, the activities of education and research, the state of operation of research facilities and others in Nuclear Engineering Research Laboratory, University of Tokyo in fiscal year 1992 are summarized. In this Laboratory, there are four large research facilities, that are, the fast neutron source reactor 'Yayoi', the electron beam linac, the nuclear fusion reactor blanket experiment facility and the heavy irradiation research facility. Those are used for carrying out education and research in the wide fields of nuclear engineering, and are offered also for joint utilization. The results of research by using respective research facilities have been summarized in separate reports. The course of the management and operation of each research facility is described, and the research activities, the theses for doctorate and graduation these of teachers, personnel and graduate students in the Laboratory are summarized. (J.P.N.)

Review of Heavy-Duty Engine Combustion Research at Sandia National Laboratories

International Nuclear Information System (INIS)

Robert W. Carling; Gurpreet Singh

2000-01-01

The objectives of this paper are to describe the research efforts in diesel engine combustion at Sandia National Laboratories' Combustion Research Facility and to provide recent experimental results. We have four diesel engine experiments supported by the Department of Energy, Office of Heavy Vehicle Technologies: a one-cylinder version of a Cummins heavy-duty engine, a diesel simulation facility, a one-cylinder Caterpillar engine to evaluate combustion of alternative fuels, and a homogeneous-charge, compression-ignition (HCCI) engine facility is under development. Recent experimental results to be discussed are: the effects of injection timing and diluent addition on late-combustion soot burnout, diesel-spray ignition and premixed-burn behavior, a comparison of the combustion characteristics of M85 (a mixture of 85% methanol and 15% gasoline) and DF2 (No.2 diesel reference fuel), and a description of our HCCI experimental program and modeling work

The International Cooperation on Remote Laboratories in the Framework of Engineering Didactics

Directory of Open Access Journals (Sweden)

Raivo Sell

2015-02-01

Full Text Available In the present paper the interactive demonstration of remote laboratories conducted with engineering didactics for creating real conditions for teaching and learning engineering has been presented. The article is focusing on international cooperation, offering the wide range of tools and methodology for effective and interactive teaching of embedded systems and mechatronics as well as exploiting latest web technologies, and offering flexibility and freedom for students.

Expanding Usability of Virtual Network Laboratory in IT Engineering Education

Directory of Open Access Journals (Sweden)

Dalibor M Dobrilovic

2013-02-01

Full Text Available This paper deals with importance of virtual network laboratories usage in IT engineering education. It presents the particular virtual network laboratory model developed for usage in Computer Networks course as well. This virtual network laboratory, called VNLab, is based on virtualization technology. It has been successfully tested in educational process of Computer Network course for IT undergraduate students. Its usability for network related courses is analyzed by comparison of recommended curricula’s of world organizations such as IEEE, ACM and AIS. This paper is focused on expanding the usability of this virtual network laboratory to other non-network related courses. The primary expansion field is in domain of IT System Administration, IT Systems and Data Security and Operating Systems as well. The possible learning scenarios, learning tools and concepts for making this system applicable in these three additional fields are presented by the analyses of compatibility with recommended learning topics and outcomes by IEEE, ACM and AIS.

Biennial Survey of Education, 1916-18. Volume II. Bulletin, 1919, No. 89

Science.gov (United States)

Bureau of Education, Department of the Interior, 1921

1921-01-01

Volume II of the Biennial Survey of Education, 1916-1918 includes the following chapters: (1) Education in Great Britain and Ireland (I. L. Kandel); (2) Education in parts of the British Empire: Educational Developments in the Dominion of Canada (Walter A. Montgomery), Public School System of Jamaica (Charles A. Asbury), Recent Progress of…

A study of quasi-biennial oscillation in the tropical stratosphere

Science.gov (United States)

Sasi, M. N.; Krishna Murthy, B. V.

1991-12-01

The characteristics of the quasi-biennial oscillation in zonal wind and temperature at Trivandrum (8.5°N, 77°E) have been studied using data covering 16 years. Similar study has been carried out for zonal wind at Balasore (21.5°N, 87°E) using data covering 9 years. The cycle to cycle variation of amplitudes, their altitude variation, periods and descent rates of the westerly and easterly regimes have been studied.

Idaho National Engineering Laboratory radioecology and ecology programs. 1983 progress report

International Nuclear Information System (INIS)

Markham, O.D.

1983-06-01

Progress is reported in research on: the baseline ecology of the Idaho National Engineering Laboratory (INEL), the effects of disturbance on animal and plant communities, and the behavior of radionuclides in the environment surrounding radioactive waste sites. Separate abstracts have been prepared for individual reports

Idaho National Engineering Laboratory radioecology and ecology programs. 1983 progress report

Energy Technology Data Exchange (ETDEWEB)

Markham, O. D. [ed.

1983-06-01

Progress is reported in research on: the baseline ecology of the Idaho National Engineering Laboratory (INEL), the effects of disturbance on animal and plant communities, and the behavior of radionuclides in the environment surrounding radioactive waste sites. Separate abstracts have been prepared for individual reports. (ACR)

Proceedings of the National Renewable Energy Laboratory Wind Energy Systems Engineering Workshop

Energy Technology Data Exchange (ETDEWEB)

Dykes, K.

2014-12-01

The second National Renewable Energy Laboratory (NREL) Wind Energy Systems Engineering Workshop was held in Broomfield, Colorado, from January 29 to February 1, 2013. The event included a day-and-a-half workshop exploring a wide variety of topics related to system modeling and design of wind turbines and plants. Following the workshop, 2 days of tutorials were held at NREL, showcasing software developed at Sandia National Laboratories, the National Aeronautics and Space Administration's Glenn Laboratories, and NREL. This document provides a brief summary of the various workshop activities and includes a review of the content and evaluation results from attendees.

Proceedings of the second biennial international conference on nascent technologies in engineering: souvenir

International Nuclear Information System (INIS)

2017-01-01

This conference touches upon the different aspects of engineering and related technologies. The topics covered are: structural control, dynamics and health monitoring; manufacturing and management strategies; thermal engineering and fluid dynamics; power systems; electrical machines and drives; power electronics and energy conversion; signal processing; embedded system; communication engineering; networking/ analysis and design of algorithms; security and information and computer technologies. Papers relevant to INIS are indexed separately

Software Engineering Laboratory (SEL) database organization and user's guide

Science.gov (United States)

So, Maria; Heller, Gerard; Steinberg, Sandra; Spiegel, Douglas

1989-01-01

The organization of the Software Engineering Laboratory (SEL) database is presented. Included are definitions and detailed descriptions of the database tables and views, the SEL data, and system support data. The mapping from the SEL and system support data to the base tables is described. In addition, techniques for accessing the database, through the Database Access Manager for the SEL (DAMSEL) system and via the ORACLE structured query language (SQL), are discussed.

Ecological risk assessment at the Idaho National Engineering Laboratory: Overview

International Nuclear Information System (INIS)

VanHorn, R.; Bensen, T.; Green, T.; Hampton, N.; Staley, C.; Morris, R.; Brewer, R.; Peterson, S.

1994-01-01

The paper will present an overview of the methods and results of the screening level ecological risk assessment (ERA) performed at the Idaho National Engineering Laboratory (INEL). The INEL is a site with some distinct characteristics. First it is a large Department of Energy (DOE) laboratory (2,300 km 2 ) having experienced 40 years of nuclear material production operations. Secondly, it is a relatively undisturbed cold desert ecosystem. Neither of these issues have been sufficiently addressed in previous ERAs. It was necessary in many instances to develop methods that differed from those used in other studies. This paper should provide useful methodologies for the ERAs performed at other similar sites

Activities of the IAEA Laboratories in Seibersdorf and Vienna. Biennial Report 1983-1984

International Nuclear Information System (INIS)

1985-06-01

The report presents the activities of the IAEA Laboratories in Seibersdorf and Vienna during the period 1983-1984, with emphasis on the research and development of mass rearing systems for insect control programmes applying the sterile insect technique and the tissue culture techniques for plant breeding. In chemistry and hydrology a new line was started together with the World Meteorological Organization in servicing the latter's network of stations for monitoring of background levels of air pollution all around the world. In radiation dosimetry a new automated thermoluminescent dosemeter reader was installed. The Electronics and Measurement Section has installed a new training laboratory. Six training courses and one seminar were held. An increased number of samples were analysed by the Safeguards Analytical Laboratory

ARES Biennial Report 2012 Final

Science.gov (United States)

Stansbery, Eileen

2014-01-01

Since the return of the first lunar samples, what is now the Astromaterials Research and Exploration Science (ARES) Directorate has had curatorial responsibility for all NASA-held extraterrestrial materials. Originating during the Apollo Program (1960s), this capability at Johnson Space Center (JSC) included scientists who were responsible for the science planning and training of astronauts for lunar surface activities as well as experts in the analysis and preservation of the precious returned samples. Today, ARES conducts research in basic and applied space and planetary science, and its scientific staff represents a broad diversity of expertise in the physical sciences (physics, chemistry, geology, astronomy), mathematics, and engineering organized into three offices (figure 1): Astromaterials Research (KR), Astromaterials Acquisition and Curation (KT), and Human Exploration Science (KX). Scientists within the Astromaterials Acquisition and Curation Office preserve, protect, document, and distribute samples of the current astromaterials collections. Since the return of the first lunar samples, ARES has been assigned curatorial responsibility for all NASA-held extraterrestrial materials (Apollo lunar samples, Antarctic meteorites - some of which have been confirmed to have originated on the Moon and on Mars - cosmic dust, solar wind samples, comet and interstellar dust particles, and space-exposed hardware). The responsibilities of curation consist not only of the longterm care of the samples, but also the support and planning for future sample collection missions and research and technology to enable new sample types. Curation provides the foundation for research into the samples. The Lunar Sample Facility and other curation clean rooms, the data center, laboratories, and associated instrumentation are unique NASA resources that, together with our staff's fundamental understanding of the entire collection, provide a service to the external research community

Design modification and optimisation of the perfusion system of a tri-axial bioreactor for tissue engineering.

Science.gov (United States)

Hussein, Husnah; Williams, David J; Liu, Yang

2015-07-01

A systematic design of experiments (DOE) approach was used to optimize the perfusion process of a tri-axial bioreactor designed for translational tissue engineering exploiting mechanical stimuli and mechanotransduction. Four controllable design parameters affecting the perfusion process were identified in a cause-effect diagram as potential improvement opportunities. A screening process was used to separate out the factors that have the largest impact from the insignificant ones. DOE was employed to find the settings of the platen design, return tubing configuration and the elevation difference that minimise the load on the pump and variation in the perfusion process and improve the controllability of the perfusion pressures within the prescribed limits. DOE was very effective for gaining increased knowledge of the perfusion process and optimizing the process for improved functionality. It is hypothesized that the optimized perfusion system will result in improved biological performance and consistency.

Idaho National Engineering and Environmental Laboratory Environmental Technologies Proof-of-Concepts. Final report FY-96

Energy Technology Data Exchange (ETDEWEB)

Barrie, S.L.; Carpenter, G.S.; Crockett, A.B. [and others

1997-04-01

The Idaho National Engineering and Environmental Laboratory Environmental Technologies Proof-of-Concept Project was initiated for the expedited development of new or conceptual technologies in support of groundwater fate, transport, and remediation; buried waste characterization, retrieval, and treatment; waste minimization/pollution prevention; and spent fuel handling and storage. In Fiscal Year 1996, The Idaho National Engineering and Environmental Laboratory proposed 40 development projects and the Department of Energy funded 15. The projects proved the concepts of the various technologies, and all the technologies contribute to successful environmental management.

Idaho National Engineering and Environmental Laboratory Environmental Technologies Proof-of-Concepts. Final report FY-96

International Nuclear Information System (INIS)

Barrie, S.L.; Carpenter, G.S.; Crockett, A.B.

1997-04-01

The Idaho National Engineering and Environmental Laboratory Environmental Technologies Proof-of-Concept Project was initiated for the expedited development of new or conceptual technologies in support of groundwater fate, transport, and remediation; buried waste characterization, retrieval, and treatment; waste minimization/pollution prevention; and spent fuel handling and storage. In Fiscal Year 1996, The Idaho National Engineering and Environmental Laboratory proposed 40 development projects and the Department of Energy funded 15. The projects proved the concepts of the various technologies, and all the technologies contribute to successful environmental management

Develop virtual joint laboratory for education like distance engineering system for robotic applications

Science.gov (United States)

Latinovic, T. S.; Deaconu, S. I.; Latinović, M. T.; Malešević, N.; Barz, C.

2015-06-01

This paper work with a new system that provides distance learning and online training engineers. The purpose of this paper is to develop and provide web-based system for the handling and control of remote devices via the Internet. Remote devices are currently the industry or mobile robots [13]. For future product development machine in the factory will be included in the system. This article also discusses the current use of virtual reality tools in the fields of science and engineering education. One programming tool in particular, virtual reality modeling language (VRML) is presented in the light of its applications and capabilities in the development of computer visualization tool for education. One contribution of this paper is to present the software tools and examples that can encourage educators to develop a virtual reality model to improve teaching in their discipline. [12] This paper aims to introduce a software platform, called VALIP where users can build, share, and manipulate 3D content in cooperation with the interaction processes in a 3D context, while participating hardware and software devices can be physical and / or logical distributed and connected together via the Internet. VALIP the integration of virtual laboratories to appropriate partners; therefore, allowing access to all laboratories in any of the partners in the project. VALIP provides advanced laboratory for training and research within robotics and production engineering, and thus, provides a great laboratory facilities with only having to invest a limited amount of resources at the local level to the partner site.

Costs and cost-effectiveness of full implementation of a biennial faecal occult blood test screening program for bowel cancer in Australia.

Science.gov (United States)

Pignone, Michael P; Flitcroft, Kathy L; Howard, Kirsten; Trevena, Lyndal J; Salkeld, Glenn P; St John, D James B

2011-02-21

To examine the costs and cost-effectiveness of full implementation of biennial bowel cancer screening for Australian residents aged 50-74 years. Identification of existing economic models from 1993 to 2010 through searches of PubMed and economic analysis databases, and by seeking expert advice; and additional modelling to determine the costs and cost-effectiveness of full implementation of biennial faecal occult blood test screening for the five million adults in Australia aged 50-74 years. Estimated number of deaths from bowel cancer prevented, costs, and cost-effectiveness (cost per life-year gained [LYG]) of biennial bowel cancer screening. We identified six relevant economic analyses, all of which found colorectal cancer (CRC) screening to be very cost-effective, with costs per LYG under $55,000 per year in 2010 Australian dollars. Based on our additional modelling, we conservatively estimate that full implementation of biennial screening for people aged 50-74 years would have gross costs of $150 million, reduce CRC mortality by 15%-25%, prevent 300-500 deaths from bowel cancer, and save 3600-6000 life-years annually, for an undiscounted cost per LYG of $25,000-$41,667, compared with no screening, and not taking cost savings as a result of treatment into consideration. The additional expenditure required, after accounting for reductions in CRC incidence, savings in CRC treatment costs, and existing ad-hoc colonoscopy use, is likely to be less than $50 million annually. Full implementation of biennial faecal occult blood test screening in Australia can reduce bowel cancer mortality, and is an efficient use of health resources that would require modest additional government investment.

Idaho National Engineering Laboratory installation roadmap document

International Nuclear Information System (INIS)

1993-01-01

The roadmapping process was initiated by the US Department of Energy's office of Environmental Restoration and Waste Management (EM) to improve its Five-Year Plan and budget allocation process. Roadmap documents will provide the technical baseline for this planning process and help EM develop more effective strategies and program plans for achieving its long-term goals. This document is a composite of roadmap assumptions and issues developed for the Idaho National Engineering Laboratory (INEL) by US Department of Energy Idaho Field Office and subcontractor personnel. The installation roadmap discusses activities, issues, and installation commitments that affect waste management and environmental restoration activities at the INEL. The High-Level Waste, Land Disposal Restriction, and Environmental Restoration Roadmaps are also included

The Effect of an Open-Ended Design Experience on Student Achievement in an Engineering Laboratory Course

Directory of Open Access Journals (Sweden)

Matthew Cullin

2017-11-01

Full Text Available This study explores the effect of incorporating an Open-Ended Design Experience (OEDE into an undergraduate materials science laboratory taken by third-year mechanical engineering students. The focus of the OEDE was carbon fiber reinforced plastics and sandwich structures. The results indicate that the incorporation of OEDE’s in laboratory courses produces significant benefits in terms of student engagement, participation, and perception of competence. In addition, the OEDE was found to enhance students’ ability to apply related concepts as compared to non-OEDE lab activities. The authors conclude that the incorporation of OEDE’s can increase the effectiveness of engineering laboratory courses.

Tiger Team assessment of the Idaho National Engineering Laboratory

Energy Technology Data Exchange (ETDEWEB)

Goldberg, Edward S.; Keating, John J.

1991-08-01

The Management Subteam conducted a management assessment of Environment, Safety, and Health (ES H) programs and their implementation of Idaho National Engineering Laboratory (INEL). The objectives of the assessment were to: (1) evaluate the effectiveness of existing management functions and processes in terms of ensuring environmental compliance, and the health and safety of workers and the general public; and (2) identify probable root causes for ES H findings and concerns. Organizations reviewed were DOE-Headquarters: DOE Field Offices, Chicago (CH) and Idaho (ID); Argonne Area Offices, East (AAO-E) and West (AAO-W); Radiological and Environmental Sciences Laboratory (RESL); Argonne National Laboratory (ANL); EG G Idaho, Inc. (EG G); Westinghouse Idaho Nuclear Company, Inc. (WINCO); Rockwell-INEL; MK-Ferguson of Idaho Company (MK-FIC); and Protection Technology of Idaho, Inc. (PTI). The scope of the assessment covered the following ES H management issues: policies and procedures; roles, responsibilities, and authorities; management commitment; communication; staff development, training, and certification; recruitment; compliance management; conduct of operations; emergency planning and preparedness; quality assurance; self assessment; oversight activities; and cost plus award fee processes.

Evaluation of engineered barriers at the Idaho National Engineering and Environmental Laboratory

International Nuclear Information System (INIS)

Bhatt, R.N.; Porro, I.

1998-03-01

Subsurface Disposal (SDA) of the Radioactive Waste Management Complex serves as the low level waste burial ground at the Idaho National Engineering and Environmental Laboratory (INEEL). The low level wastes are buried in trenches, pits, and soil vaults in surficial sediments. A closure/post-closure plan must be written prior to closure of the SDA. The closure plan for the facility must include a design for an engineered barrier closure cover that will meet all applicable regulatory requirements. This paper describes the approach being followed at the INEEL to choose an appropriate cover design for the SDA closure. Regulatory requirements and performance objectives potentially applicable to closure of the SDA were identified. Technical issues related to SDA closure were identified from a literature search of previous arid site engineered barrier studies and from previous SDA closure cover evaluations. Five engineered barrier conceptual design alternatives were identified: (1) a bio/capillary barrier cover, (2) a thin soil cover, (3) a thick soil cover, (4) a Resource Conservation and Recovery Act cover, and (5) a concrete sealed surface cover. Two of these designs were chosen for in situ hydraulic testing, rather than all five, in order to maximize the amount of information generated relative to projected project costs. Testing of these two cover designs provides data to quantify hydrologic model input parameters and for verification of site specific hydrologic models for long term closure cover performance evaluation and detailed analysis of closure cover alternatives. The specific objectives of the field tests are to determine the water balance for the two covers over several years and to determine cover soil physical and hydraulic properties

Pilot-Scale Laboratory Instruction for Chemical Engineering: The Specific Case of the Pilot-Unit Leading Group

Science.gov (United States)

Billet, Anne-Marie; Camy, Severine; Coufort-Saudejaud, Carole

2010-01-01

This paper presents an original approach for Chemical Engineering laboratory teaching that is currently applied at INP-ENSIACET (France). This approach, referred to as "pilot-unit leading group" is based on a partial management of the laboratories by the students themselves who become temporarily in charge of one specific laboratory. In…

Annual report of Nuclear Engineering Research Laboratory, Faculty of Engineering, University of Tokyo, fiscal year 1996

International Nuclear Information System (INIS)

1997-08-01

This report summarizes research and educational activities, operation status of the research facilities of the Nuclear Engineering Research Laboratory, Faculty of Engineering, University of Tokyo on fiscal year 1996. This facility has four major research facilities such as fast neutron source reactor 'Yayoi', electron Linac, fundamental experiment facility for nuclear fusion reactor blanket design and high fluence irradiation facility(HIT). Education and research activities are conducted in a wide fields of nuclear engineering using these facilities. The former two facilities are available for various studies by universities all over Japan, facility for nuclear fusion reactor blanket design is utilized for research within the Faculty of Engineering and HIT is used for the research within the University of Tokyo. The facility established a plan to reorganized into a nation wide research collaboration center in fiscal year 1995 and after further discussion of a future program it is decided to hold 'Nuclear energy symposium' periodically after fiscal year 1997 as a part of the activity for appealing the research results to the public. (G.K.)

Robotic applications at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Griebenow, B.E.; Marts, D.J.

1990-01-01

The Idaho National Engineering Laboratory (INEL) has several programs and projected programs that involve work in hazardous environments. Robotics/remote handling technology is being considered for an active role in these programs. The most appealing aspect of using robotics is in the area of personnel safety. Any task requiring an individual to enter a hazardous or potentially hazardous environment can benefit substantially from robotics by removing the operator from the environment and having him conduct the work remotely. Several INEL programs were evaluated based on their applications for robotics and the results and some conclusions are discussed in this paper. 1 fig

Idaho National Engineering Laboratory Waste Management Operations Roadmap Document

International Nuclear Information System (INIS)

Bullock, M.

1992-04-01

At the direction of the Department of Energy-Headquarters (DOE-HQ), the DOE Idaho Field Office (DOE-ID) is developing roadmaps for Environmental Restoration and Waste Management (ER ampersand WM) activities at Idaho National Engineering Laboratory (INEL). DOE-ID has convened a select group of contractor personnel from EG ampersand G Idaho, Inc. to assist DOE-ID personnel with the roadmapping project. This document is a report on the initial stages of the first phase of the INEL's roadmapping efforts

Assessment of the quality of test results from selected civil engineering material testing laboratories in Tanzania

CSIR Research Space (South Africa)

Mbawala, SJ

2017-12-01

Full Text Available Civil and geotechnical engineering material testing laboratories are expected to produce accurate and reliable test results. However, the ability of laboratories to produce accurate and reliable test results depends on many factors, among others...

Analysis of biennial outbreak pattern of respiratory syncytial virus according to subtype (A and B) in the Zagreb region.

Science.gov (United States)

Mlinaric-Galinovic, Gordana; Tabain, Irena; Kukovec, Tamara; Vojnovic, Gordana; Bozikov, Jadranka; Bogovic-Cepin, Jasna; Ivkovic-Jurekovic, Irena; Knezovic, Ivica; Tesovic, Goran; Welliver, Robert C

2012-06-01

The epidemic pattern of respiratory syncytial virus (RSV) in Croatia is biennial. In order to determine if the circulation of different RSV subtypes affects the outbreak cycle, the aim of the present study was to analyze the epidemic pattern of RSV in children in Croatia (Zagreb region) over a period of 3 consecutive years. The study group consisted of 696 inpatients, aged 0-5 years, who were hospitalized with acute respiratory tract infections caused by RSV, in Zagreb, in the period 1 January 2006-31 December 2008. The virus was identified in nasopharyngeal secretions using direct immunofluorescence. The virus subtype was determined on real-time polymerase chain reaction. Of 696 RSV infections identified in children, subtype A virus caused 374 infections, and subtype B, 318. Four patients had a dual RSV infection (subtypes A and B). The period of study was characterized by four epidemic waves of RSV infections: the first, smaller, in the spring of 2006; the second, larger, in December 2006/January 2007; the third in spring 2008, followed by a fourth outbreak beginning in November of 2008. The biennial virus cycles were persistent although the predominant RSV subtype in the first two epidemic waves was subtype B, and in the second two it was subtype A. Over a 3 year period of observation, the biennial RSV cycle in Croatia cannot be explained by a difference in the predominant circulating subtype of RSV. Other unknown factors account for the biennial cycle of RSV epidemics in Croatia. © 2011 The Authors. Pediatrics International © 2011 Japan Pediatric Society.

Sandia National Laboratories ASCI Applications Software Quality Engineering Practices; TOPICAL

International Nuclear Information System (INIS)

ZEPPER, JOHN D.; ARAGON, KATHRYN MARY; ELLIS, MOLLY A.; BYLE, KATHLEEN A.; EATON, DONNA SUE

2002-01-01

This document provides a guide to the deployment of the software verification activities, software engineering practices, and project management principles that guide the development of Accelerated Strategic Computing Initiative (ASCI) applications software at Sandia National Laboratories (Sandia). The goal of this document is to identify practices and activities that will foster the development of reliable and trusted products produced by the ASCI Applications program. Document contents include an explanation of the structure and purpose of the ASCI Quality Management Council, an overview of the software development lifecycle, an outline of the practices and activities that should be followed, and an assessment tool. These sections map practices and activities at Sandia to the ASCI Software Quality Engineering: Goals, Principles, and Guidelines, a Department of Energy document

Fuels and Materials Division biennial report, fiscal years 1979 and 1980

International Nuclear Information System (INIS)

Brown, H.L.

1980-10-01

The Fuels and Materials Division of EG and G Idaho, Inc., reports its technical activities for the fiscal years 1979 to 1980. This Division supports technical programs at the Idaho National Engineering Laboratory with materials science, materials engineering, nondestructive evaluation engineering, and remote handling of radioactive and other hazardous materials and conducts several direct-funded materials-related programs for the US Department of Energy. This report details programmatic and other support activities, direct-funded programs, organization and facility status, and EG and G Idaho-funded technical development programs

eLearning Hands-On: Blending Interactive eLearning with Practical Engineering Laboratory

Science.gov (United States)

Kiravu, Cheddi; Yanev, Kamen M.; Tunde, Moses O.; Jeffrey, Anna M.; Schoenian, Dirk; Renner, Ansel

2016-01-01

Purpose: Integrating laboratory work into interactive engineering eLearning contents augments theory with practice while simultaneously ameliorating the apparent theory-practice gap in traditional eLearning. The purpose of this paper is to assess and recommend media that currently fulfil this desirable dual pedagogical goal.…

Time variation of meteorological elements as controlled by the quasi-biennial periodicity in the solar phenomena

International Nuclear Information System (INIS)

Inoue, Michiharu; Sakurai, Kunitomo

1981-01-01

It is shown that the quasi-biennial oscillation observed on some meteorological elements as the ozone content at middle latitudes, both north and south, the zonal wind velocity at the equator and the ground-level temperature at middle latitudes, is produced by the variation of the ultraviolet flux emitted from the sun, which is varying with the solar activity with the period of about 26 months. The ozone content is varying in phase with the ultraviolet flux and the solar activity, whereas the other two elements mentioned above are changing out of phase with these phenomena. There is a possibility that both these meteorological elements and the solar activity are varying quasi-biennially while being modulated by the 26 month periodicity in the efficiency of thermonuclear fusions at the central core of the sun. (author)

IOTA interferometer project - Plans, engineering, and laboratory results

International Nuclear Information System (INIS)

Reasenberg, R.D.

1990-01-01

The Infrared-Optical Telescope Array (IOTA) is being developed by a consortium comprising Harvard University, the MIT Lincoln Laboratory, the Smithsonian Astrophysical Observatory, the University of Massachusetts at Amherst, and the University of Wyoming. The instrument is intended to generate high-resolution images of astronomical objects by bringing together beams from widely separated telescopes and combining them at a central location. The initial configuration will consist of two 0.45 m telescopes thay may range along an L-shaped track that will permit spacings in the 5 to 38 m range, at the Smithsonian's Fred L. Whipple Observatory on Mt. Hopkins. Initial tests of this configuration are expected to be conducted during the summer of 1991 and to yield both valuable engineering data and the first scientific results including diameters of stars and artificial earth satellites and a measure of the extent of some circumstellar shells. The engineering data will be applied to the refinement of IOTA, particularly to the second IOTA configuration, in which a third telescope will be added, making it possible to obtain phase closure information. 7 refs

Engineering Encounters: An Engineering Design Process for Early Childhood

Science.gov (United States)

Lottero-Perdue, Pamela; Bowditch, Michelle; Kagan, Michelle; Robinson-Cheek, Linda; Webb, Tedra; Meller, Megan; Nosek, Theresa

2016-01-01

This column presents ideas and techniques to enhance your science teaching. This month's issue shares information about trying (again) to engineer an egg package. Engineering is an essential part of science education, as emphasized in the "Next Generation Science Standards" (NGSS Lead States 2013). Engineering practices and performance…

Tiger Team assessment of the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

1991-08-01

The Management Subteam conducted a management assessment of Environment, Safety, and Health (ES ampersand H) programs and their implementation of Idaho National Engineering Laboratory (INEL). The objectives of the assessment were to: (1) evaluate the effectiveness of existing management functions and processes in terms of ensuring environmental compliance, and the health and safety of workers and the general public; and (2) identify probable root causes for ES ampersand H findings and concerns. Organizations reviewed were DOE-Headquarters: DOE Field Offices, Chicago (CH) and Idaho (ID); Argonne Area Offices, East (AAO-E) and West (AAO-W); Radiological and Environmental Sciences Laboratory (RESL); Argonne National Laboratory (ANL); EG ampersand G Idaho, Inc. (EG ampersand G); Westinghouse Idaho Nuclear Company, Inc. (WINCO); Rockwell-INEL; MK-Ferguson of Idaho Company (MK-FIC); and Protection Technology of Idaho, Inc. (PTI). The scope of the assessment covered the following ES ampersand H management issues: policies and procedures; roles, responsibilities, and authorities; management commitment; communication; staff development, training, and certification; recruitment; compliance management; conduct of operations; emergency planning and preparedness; quality assurance; self assessment; oversight activities; and cost plus award fee processes

Biennial-Aligned Lunisolar-Forcing of ENSO: Implications for Simplified Climate Models

Science.gov (United States)

Pukite, P. R.

2017-12-01

By solving Laplace's tidal equations along the equatorial Pacific thermocline, assuming a delayed-differential effective gravity forcing due to a combined lunar+solar (lunisolar) stimulus, we are able to precisely match ENSO periodic variations over wide intervals. The underlying pattern is difficult to decode by conventional means such as spectral analysis, which is why it has remained hidden for so long, despite the excellent agreement in the time-domain. What occurs is that a non-linear seasonal modulation with monthly and fortnightly lunar impulses along with a biennially-aligned "see-saw" is enough to cause a physical aliasing and thus multiple folding in the frequency spectrum. So, instead of a conventional spectral tidal decomposition, we opted for a time-domain cross-validating approach to calibrate the amplitude and phasing of the lunisolar cycles. As the lunar forcing consists of three fundamental periods (draconic, anomalistic, synodic), we used the measured Earth's length-of-day (LOD) decomposed and resolved at a monthly time-scale [1] to align the amplitude and phase precisely. Even slight variations from the known values of the long-period tides will degrade the fit, so a high-resolution calibration is possible. Moreover, a narrow training segment from 1880-1920 using NINO34/SOI data is adequate to extrapolate the cycles of the past 100 years (see attached figure). To further understand the biennial impact of a yearly differential-delay, we were able to also decompose using difference equations the historical sea-level-height readings at Sydney harbor to clearly expose the ENSO behavior. Finally, the ENSO lunisolar model was validated by back-extrapolating to Unified ENSO coral proxy (UEP) records dating to 1650. The quasi-biennial oscillation (QBO) behavior of equatorial stratospheric winds derives following a similar pattern to ENSO via the tidal equations, but with an emphasis on draconic forcing. This improvement in ENSO and QBO understanding has

An Alternative Educational Approach for an Inorganic Chemistry Laboratory Course in Industrial and Chemical Engineering

Science.gov (United States)

Garces, Andres; Sanchez-Barba, Luis Fernando

2011-01-01

We describe an alternative educational approach for an inorganic chemistry laboratory module named "Experimentation in Chemistry", which is included in Industrial Engineering and Chemical Engineering courses. The main aims of the new approach were to reduce the high levels of failure and dropout on the module and to make the content match the…

Fundamental Research in Engineering Education. Student Learning in Industrially Situated Virtual Laboratories

Science.gov (United States)

Koretsky, Milo D.; Kelly, Christine; Gummer, Edith

2011-01-01

The instructional design and the corresponding research on student learning of two virtual laboratories that provide an engineering task situated in an industrial context are described. In this problem-based learning environment, data are generated dynamically based on each student team's distinct choices of reactor parameters and measurements.…

VIII International Congress of Engineering Physics

International Nuclear Information System (INIS)

2017-01-01

The Physicist Engineering is a multidisciplinary profession in which an undergraduate student integrates and applies their knowledge of Physics, Mathematics, and Computing to adapt and innovate all kind of technologies, as well as to development and apply theoretical knowledge to different fields of science and engineering. A Physicist Engineer, supported by a solid preparation in science and engineering is available to study, analyze, identify, and solve problems in different fields of science and technology for industries, hospitals, research laboratories, institutes and governmental organizations focused on metrology, optics, energy, materials, instrumentation of sophisticated equipment. The Physicist Engineering bachelor degree is a national and international reference to encouraging all those students to apply knowledge through active participation in the operation, planning, and management of projects. The technological and scientific impact of a Physicist Engineering undergraduate and graduate students, as well as the tutorial of the research professor that are interested in Physics and Physics Engineering, may be found in a biennial event like the International Conference on Physicist Engineering, through the diffusion of both experimental and theoretical research and teaching. In order to promote and encourage strength academic goals among universities and research institutions, the International Conference on Physics Engineering Committee, integrated by a faculty meeting of the Universidad Autónoma Metropolitana, Campus Azcapotzalco, has decided to grant the VIII International Congress of Physics Engineering to the Universidad Autónoma de Yucatán, which is going to take place on Mérida, November 7 th to 11 th , 2016. This conference considers different topics as: Renewables Energies Engineering Materials Technology Nanotechnology Medical Physics Education in Physics Engineering Nuclear Engineering High Precision Instrumentation Atmosphere Physics

Correlation of Soot Formation in Turbojet Engines and in Laboratory Flames.

Science.gov (United States)

1981-02-01

TURBOJET ENGINES AND IN LABORATORY FLAMES o. . LSO[ lVEl . 7 R. K. GOULD !i~0 B ~. OLSON AERH. EM R"&OESERHLBRTREIC P.O. BOX 12 PRINCETON, NJ 08540 DT I C...than one variable is a true impro.,nent or simply a mathematical artifact. Such an examination is not -iic luded, but it seems likely that only in the

Analyzing the Function of Cartilage Replacements: A Laboratory Activity to Teach High School Students Chemical and Tissue Engineering Concepts

Science.gov (United States)

Renner, Julie N.; Emady, Heather N.; Galas, Richards J., Jr.; Zhange, Rong; Baertsch, Chelsey D.; Liu, Julie C.

2013-01-01

A cartilage tissue engineering laboratory activity was developed as part of the Exciting Discoveries for Girls in Engineering (EDGE) Summer Camp sponsored by the Women In Engineering Program (WIEP) at Purdue University. Our goal was to increase awareness of chemical engineering and tissue engineering in female high school students through a…

75 FR 43528 - Seeking Public Comment on Draft National Health Security Strategy Biennial Implementation Plan

Science.gov (United States)

2010-07-26

... National Health Security Strategy Biennial Implementation Plan AGENCY: Department of Health and Human... National Health Security Strategy (NHSS) of the United States of America (2009) and build upon the NHSS Interim Implementation Guide for the National Health Security Strategy of the United States of America...

Summaries of the Idaho National Engineering Laboratory Radioecology and Ecology Program research projects

International Nuclear Information System (INIS)

Markham, O.D.

1987-06-01

This report provides summaries of individual research projects conducted by the Idaho National Engineering Laboratory Radioecology and Ecology Program. Summaries include projects in various stages, from those that are just beginning, to projects that are in the final publication stage

Department of Energy, highly enriched uranium ES ampersand H vulnerability assessment, Idaho National Engineering Laboratory site assessment team report

International Nuclear Information System (INIS)

1996-01-01

In accordance with the February 22, 1996 directive issued by Secretary of Energy O'Leary on the Vulnerability Assessment of Highly Enriched Uranium (HEU) Storage, the Idaho National Engineering Laboratory conducted an assessment of the site's HEU holdings and any associated vulnerabilities. The assessment was conducted between April 25 and May 24, 1996. The scope of this assessment, as defined in the Assessment Plan, included all HEU, and any spent fuel not evaluated in the Spent Fuel Vulnerability Assessment. Addressed in this assessment were all of the holdings at the Idaho National Engineering Laboratory (INEL) except any located at Argonne National Laboratory-West (ANL-W) and the Naval Reactors Facility. Excluded from the assessment were those HEU holdings previously assessed in the Idaho National Engineering Laboratory Spent Nuclear Fuel Inventory and Vulnerability Site Assessment Report and any HEU holdings evaluated in the Plutonium Vulnerability Assessment Report

Radioactive effluent monitoring at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Simpson, O.D.

1975-01-01

The Effluent and Radiation Measurements Laboratory at the Idaho National Engineering Laboratory (INEL) has recently upgraded capabilities in the field of monitoring and analysis of radioactive airborne and liquid effluents using the techniques of gamma-ray spectrometry. The techniques and equipment used include remotely-operated, computer-based Ge(Li) spectrometers which obtain data on a real-time basis. Permanent record files are maintained of both the effluent release values and the gamma-ray data from which the release values are calculated. Should values for release levels ever be challenged, the gamma-ray spectral information for any measurement can be recalled and analyzed as needed. Daily effluent release reports are provided to operating personnel which contributes to prompt correction of any operational problems. Monthly, quarterly, and annual reports are compiled which provide inventories of the radionuclides released. A description of the effluent monitoring, reporting and records system developed at INEL for this application will be presented

Use of the LITEE Lorn Manufacturing Case Study in a Senior Chemical Engineering Unit Operations Laboratory

Science.gov (United States)

Abraham, Nithin Susan; Abulencia, James Patrick

2011-01-01

This study focuses on the effectiveness of incorporating the Laboratory for Innovative Technology and Engineering Education (LITEE) Lorn Manufacturing case into a senior level chemical engineering unit operations course at Manhattan College. The purpose of using the case study is to demonstrate the relevance of ethics to chemical engineering…

1986 environmental monitoring program report for the Idaho National Engineering Laboratory Site

International Nuclear Information System (INIS)

Hoff, D.L.; Chew, E.W.; Rope, S.K.

1987-05-01

This report presents onsite and offsite data collected in 1986 for the routine environmental monitoring program conducted by the Radiological and Environmental Sciences Laboratory (RESL) of the Department of Energy (DOE) at the Idaho National Engineering Laboratory (INEL) Site. The purpose of this routine program is to monitor radioactive and nonradioactive materials resulting from INEL Site operations which may reach the surrounding offsite environment and population. This report is prepared in accordance with the DOE requirements in draft DOE Order 5484.1 and is not intended to cover the numerous special environmental research programs being conducted at the INEL by RESL and others

NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 56: Technical Communications in Engineering and Science: The Practices Within a Government Defense Laboratory

Science.gov (United States)

VonSeggern, Marilyn; Jourdain, Janet M.; Pinelli, Thomas E.

1996-01-01

Research in recent decades has identified the varied information needs of engineers versus scientists. While most of that research looked at the differences among organizations, we surveyed engineers and scientists within a single Air Force research and development laboratory about their information gathering, usage, and production practices. The results of the Phillips Laboratory survey confirm prior assumptions about distinctions between engineering and science. Because military employees responded at a much higher rate than civilian staff, the survey also became an opportunity to profile a little-known segment of the engineer/scientist population. In addition to the effect Phillips Laboratory's stated mission may have on member engineers and scientists, other factors causing variations in technical communication and information-related activities are identified.

The laboratory test rig with miniature jet engine to research aviation fuels combustion process

Directory of Open Access Journals (Sweden)

Gawron Bartosz

2015-12-01

Full Text Available This article presents laboratory test rig with a miniature turbojet engine (MiniJETRig – Miniature Jet Engine Test Rig, that was built in the Air Force Institute of Technology. The test rig has been developed for research and development works aimed at modelling and investigating processes and phenomena occurring in full scale jet engines. In the article construction of a test rig is described, with a brief discussion on the functionality of each of its main components. Additionally examples of measurement results obtained during the realization of the initial tests have been included, presenting the capabilities of the test rig.

Buried waste remote survey of the Idaho National Engineering Laboratory subsurface disposal area

International Nuclear Information System (INIS)

Richardson, B.S.; Noakes, M.W.; Griebenow, B.E.; Josten, N.E.

1991-01-01

Burial site characterization is an important first step in the restoration of subsurface disposal sites. Testing and demonstration of technology for remote buried waste site characterization were performed at the Idaho National Engineering Laboratory (INEL) by a team from five US Department of Energy (DOE) laboratories. The US Army's Soldier Robot Interface Project (SRIP) vehicle, on loan to the Oak Ridge National Laboratory (ORNL), was used as a remotely operated sensor platform. The SRIP was equipped with an array of sensors including terrain conductivity meter, magnetometer, ground-penetrating radar (GPR), organic vapor detector, gamma-based radar detector, and spectrum analyzer. The testing and demonstration were successfully completed and provided direction for future work in buried waste site characterization

Biennial activity report of Metallurgy Division for 1989 and 1990

International Nuclear Information System (INIS)

Kamachi Mudali, U.; Muraleedharan, P.; Parameswaran, P.; Swaminathan, K.; Sreedharan, O.M.

1993-01-01

This is the first divisional biennial report of the Metallurgy Division of Indira Gandhi Centre for Atomic Research, for the year 1989-1990, after formation of the Metallurgy Division in September 1988. Major areas of work in the Division relate to aqueous corrosion and localised corrosion, stress corrosion cracking and liquid metal corrosion, high temperature oxidation, thermodynamic studies, physical metallurgy studies for structure-property correlations and failure analyses. The principal materials of studies have been the austenitic stainless steels, the current materials of construction in the Fast Breeder Test Reactor and the candidate materials for the Prototype Fast Breeder Reactor

75 FR 28517 - 2004 and 2006 Biennial Regulatory Reviews-Streamlining and Other Revisions of the Commission's...

Science.gov (United States)

2010-05-21

... Commission for the transmission of radio energy, the owner of the tower shall maintain the prescribed.... FOR FURTHER INFORMATION CONTACT: John Borkowski, Wireless Telecommunications Bureau, (202) 418-0626, e... its 2004 Biennial Review Comments, PCIA--the Wireless Infrastructure Association (PCIA) states that...

Annual report of Nuclear Engineering Research Laboratory, Faculty of Engineering, University of Tokyo, fiscal year 1994

International Nuclear Information System (INIS)

1995-08-01

This annual report is the summary of the research and education activities, the state of operating research facilities and others in fiscal year 1994 in this Research Laboratory. In this Research Laboratory, there are four main installations, namely the fast neutron source reactor 'Yayoi', the electron linear accelerator, the basic experiment facility for the design of nuclear fusion reactor blanket and the heavy irradiation research facility. The former two are put to the joint utilization by all Japanese universities, the blanket is to that within Faculty of Engineering, and the HIT is to that within this university. The fast neutron science research facility, the installation of which was approved in 1993 as the ancillary equipment of the Yayoi, has been put to the joint utilization for all Japan, and achieved good results. In this report, the management and operation of these main installations, research activities, the publication of research papers,graduation and degree theses, the publication of research papers, graduation and degree theses, the events in the Laboratory for one year, the list of the visitors to the Laboratory, the list of the records of official trips to foreign countries and others, and the list of UTNL reports are described. (K.I.)

Environmental resource document for the Idaho National Engineering Laboratory. Volume 1

Energy Technology Data Exchange (ETDEWEB)

Irving, J.S.

1993-07-01

This document contains information related to the environmental characterization of the Idaho National Engineering Laboratory (INEL). The INEL is a major US Department of Energy facility in southeastern Idaho dedicated to nuclear research, waste management, environmental restoration, and other activities related to the development of technology. Environmental information covered in this document includes land, air, water, and ecological resources; socioeconomic characteristics and land use; and cultural, aesthetic, and scenic resources.

Environmental resource document for the Idaho National Engineering Laboratory. Volume 2

Energy Technology Data Exchange (ETDEWEB)

Irving, J.S.

1993-07-01

This document contains information related to the environmental characterization of the Idaho National Engineering Laboratory (INEL). The INEL is a major US Department of Energy facility in southeastern Idaho dedicated to nuclear research, waste management, environmental restoration, and other activities related to the development of technology. Environmental information covered in this document includes land, air, water, and ecological resources; socioeconomic characteristics and land use; and cultural, aesthetic, and scenic resources.

75 FR 23222 - National Poultry Improvement Plan; General Conference Committee Meeting and 40th Biennial Conference

Science.gov (United States)

2010-05-03

...] National Poultry Improvement Plan; General Conference Committee Meeting and 40th Biennial Conference AGENCY... notice of a meeting of the General Conference Committee of the National Poultry Improvement Plan (NPIP... Coordinator, National Poultry Improvement Plan, VS, APHIS, 1498 Klondike Road, Suite 101, Conyers, GA 30094...

77 FR 46374 - National Poultry Improvement Plan; General Conference Committee Meeting and 41st Biennial Conference

Science.gov (United States)

2012-08-03

...] National Poultry Improvement Plan; General Conference Committee Meeting and 41st Biennial Conference AGENCY... notice of a meeting of the General Conference Committee of the National Poultry Improvement Plan (NPIP... CONTACT: Dr. C. Stephen Roney, Senior Coordinator, National Poultry Improvement Plan, VS, APHIS, 1506...

Virtual laboratory learning media development to improve science literacy skills of mechanical engineering students on basic physics concept of material measurement

Science.gov (United States)

Jannati, E. D.; Setiawan, A.; Siahaan, P.; Rochman, C.

2018-05-01

This study aims to determine the description of virtual laboratory learning media development to improve science literacy skills of Mechanical Engineering students on the concept of basic Physics. Quasi experimental method was employed in this research. The participants of this research were first semester students of mechanical engineering in Majalengka University. The research instrument was readability test of instructional media. The results of virtual laboratory learning media readability test show that the average score is 78.5%. It indicates that virtual laboratory learning media development are feasible to be used in improving science literacy skill of Mechanical Engineering students in Majalengka University, specifically on basic Physics concepts of material measurement.

Changes and challenges in the Software Engineering Laboratory

Science.gov (United States)

Pajerski, Rose

1994-01-01

Since 1976, the Software Engineering Laboratory (SEL) has been dedicated to understanding and improving the way in which one NASA organization, the Flight Dynamics Division (FDD), develops, maintains, and manages complex flight dynamics systems. The SEL is composed of three member organizations: NASA/GSFC, the University of Maryland, and Computer Sciences Corporation. During the past 18 years, the SEL's overall goal has remained the same: to improve the FDD's software products and processes in a measured manner. This requires that each development and maintenance effort be viewed, in part, as a SEL experiment which examines a specific technology or builds a model of interest for use on subsequent efforts. The SEL has undertaken many technology studies while developing operational support systems for numerous NASA spacecraft missions.

Elevating Learner Achievement Using Formative Electronic Lab Assessments in the Engineering Laboratory: A Viable Alternative to Weekly Lab Reports

Science.gov (United States)

Chen, Baiyun; DeMara, Ronald F.; Salehi, Soheil; Hartshorne, Richard

2018-01-01

A laboratory pedagogy interweaving weekly student portfolios with onsite formative electronic laboratory assessments (ELAs) is developed and assessed within the laboratory component of a required core course of the electrical and computer engineering (ECE) undergraduate curriculum. The approach acts to promote student outcomes, and neutralize…

Toward the breast screening balance sheet: cumulative risk of false positives for annual versus biennial mammograms commencing at age 40 or 50.

Science.gov (United States)

Winch, Caleb J; Sherman, Kerry A; Boyages, John

2015-01-01

This study aimed to: (1) Estimate cumulative risk of recall from breast screening where no cancer is detected (a harm) in Australia; (2) Compare women screened annually versus biennially, commencing age 40 versus 50; and (3) Compare with international findings. At the no-cost metropolitan program studied, women attended biennial screening, but were offered annual screening if regarded at elevated risk for breast cancer. The cumulative risk of at least one recall was estimated using discrete-time survival analysis. Cancer detection statistics were computed. In total, 801,636 mammograms were undertaken in 231,824 women. Over 10 years, cumulative risk of recall was 13.3 % (95 % CI 12.7-13.8) for those screened biennially, and 19.9 % (CI 16.6-23.2) for those screened annually from age 50-51. Cumulative risk of complex false positive involving a biopsy was 3.1 % (CI 2.9-3.4) and 5.0 % (CI 3.4-6.6), respectively. From age 40-41, the risk of recall was 15.1 % (CI 14.3-16.0) and 22.5 % (CI 17.9-27.1) for biennial and annual screening, respectively. Corresponding rates of complex false positive were 3.3 % (CI 2.9-3.8) and 6.3 % (CI 3.4-9.1). Over 10 mammograms, invasive cancer was detected in 3.4 % (CI 3.3-3.5) and ductal carcinoma in situ in 0.7 % (CI 0.6-0.7) of women, with a non-significant trend toward a larger proportion of Tis and T1N0 cancers in women screened annually (74.5 %) versus biennially (70.1 %), χ (2) = 2.77, p = 0.10. Cancer detection was comparable to international findings. Recall risk was equal to European estimates for women screening from 50 and lower for screening from 40. Recall risk was half of United States' rates across start age and rescreening interval categories. Future benefit/harm balance sheets may be useful for communicating these findings to women.

Research reactor usage at the Idaho National Engineering Laboratory in support of university research and education

International Nuclear Information System (INIS)

Woodall, D.M.; Dolan, T.J.; Stephens, A.G.

1990-01-01

The Idaho National Engineering Laboratory is a US Department of Energy laboratory which has a substantial history of research and development in nuclear reactor technologies. There are a number of available nuclear reactor facilities which have been incorporated into the research and training needs of university nuclear engineering programs. This paper addresses the utilization of the Advanced Reactivity Measurement Facility (ARMF) and the Coupled Fast Reactivity Measurement Facility (CFRMF) for thesis and dissertation research in the PhD program in Nuclear Science and Engineering by the University of Idaho and Idaho State University. Other reactors at the INEL are also being used by various members of the academic community for thesis and dissertation research, as well as for research to advance the state of knowledge in innovative nuclear technologies, with the EBR-II facility playing an essential role in liquid metal breeder reactor research. 3 refs

Software Engineering Laboratory (SEL) database organization and user's guide, revision 2

Science.gov (United States)

Morusiewicz, Linda; Bristow, John

1992-01-01

The organization of the Software Engineering Laboratory (SEL) database is presented. Included are definitions and detailed descriptions of the database tables and views, the SEL data, and system support data. The mapping from the SEL and system support data to the base table is described. In addition, techniques for accessing the database through the Database Access Manager for the SEL (DAMSEL) system and via the ORACLE structured query language (SQL) are discussed.

Storage of transuranic contaminated solid wastes at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Wehmann, George

1975-01-01

The storage method for low-level transuranic wastes employed at the Idaho National Engineering Laboratory is discussed in detail. The techniques used for wastes containing greater than ten nanocuries of transuranic material per gram of waste as well as the technique for lesser concentrations of transuranic wastes are described. The safety, efficiency and adequacy of these storage methods are presented

Air emission inventory for the Idaho National Engineering Laboratory: 1994 emissions report

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

This report Presents the 1994 update of the Air Emission inventory for the Idaho National Engineering Laboratory (INEL). The INEL Air Emission Inventory documents sources and emissions of non-radionuclide pollutants from operations at the INEL. The report describes the emission inventory process and all of the sources at the INEL, and provides non-radionuclide emissions estimates for stationary sources.

Air emission inventory for the Idaho National Engineering Laboratory: 1994 emissions report

International Nuclear Information System (INIS)

1995-07-01

This report Presents the 1994 update of the Air Emission inventory for the Idaho National Engineering Laboratory (INEL). The INEL Air Emission Inventory documents sources and emissions of non-radionuclide pollutants from operations at the INEL. The report describes the emission inventory process and all of the sources at the INEL, and provides non-radionuclide emissions estimates for stationary sources

Tiger Team assessment of the Idaho National Engineering Laboratory

Energy Technology Data Exchange (ETDEWEB)

McKenzie, Barbara J.; West, Stephanie G.; Jones, Olga G.; Kerr, Dorothy A.; Bieri, Rita A.; Sanderson, Nancy L.

1991-08-01

The purpose of the Safety and Health (S H) Subteam assessment was to determine the effectiveness of representative safety and health programs at the Idaho National Engineering Laboratory (INEL) site. Four Technical Safety Appraisal (TSA) Teams were assembled for this purpose by the US Department of Energy (DOE), Deputy Assistant Secretary for Safety and Quality Assurance, Office of Safety Appraisals (OSA). Team No. 1 reviewed EG G Idaho, Inc. (EG G Idaho) and the Department of Energy Field Office, Idaho (ID) Fire Department. Team No. 2 reviewed Argonne National Laboratory-West (ANL-W). Team No. 3 reviewed selected contractors at the INEL; specifically, Morrison Knudsen-Ferguson of Idaho Company (MK-FIC), Protection Technology of Idaho, Inc. (PTI), Radiological and Environmental Sciences Laboratory (RESL), and Rockwell-INEL. Team No. 4 provided an Occupational Safety and Health Act (OSHA)-type compliance sitewide assessment of INEL. The S H Subteam assessment was performed concurrently with assessments conducted by Environmental and Management Subteams. Performance was appraised in the following technical areas: Organization and Administration, Quality Verification, Operations, Maintenance, Training and Certification, Auxiliary Systems, Emergency Preparedness, Technical Support, Packaging and Transportation, Nuclear Criticality Safety, Security/Safety Interface, Experimental Activities, Site/Facility Safety Review, Radiological Protection, Personnel Protection, Worker Safety and Health (OSHA) Compliance, Fire Protection, Aviation Safety, Medical Services, and Firearms Safety.

Tiger Team assessment of the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

1991-08-01

This report documents the Tiger Team Assessment of the Idaho National Engineering Laboratory (INEL) located in Idaho Falls, Idaho. INEL is a multiprogram, laboratory site of the US Department of Energy (DOE). Overall site management is provided by the DOE Field Office, Idaho; however, the DOE Field Office, Chicago has responsibility for the Argonne National Laboratory-West facilities and operations through the Argonne Area Office. In addition, the Idaho Branch Office of the Pittsburgh Naval Reactors Office has responsibility for the Naval Reactor Facility (NRF) at the INEL. The assessment included all DOE elements having ongoing program activities at the site except for the NRF. In addition, the Safety and Health Subteam did not review the Westinghouse Idaho Nuclear Company, Inc. facilities and operations. The Tiger Team Assessment was conducted from June 17 to August 2, 1991, under the auspices of the Office of Special Projects, Office of the Assistant Secretary for Environment, Safety and Health, Headquarters, DOE. The assessment was comprehensive, encompassing environmental, safety, and health (ES ampersand H) disciplines; management; and contractor and DOE self-assessments. Compliance with applicable federal, state, and local regulations; applicable DOE Orders; best management practices; and internal INEL site requirements was assessed. In addition, an evaluation of the adequacy and effectiveness of the DOE and the site contractors management of ES ampersand H/quality assurance programs was conducted

Tiger Team assessment of the Idaho National Engineering Laboratory

Energy Technology Data Exchange (ETDEWEB)

1991-08-01

This report documents the Tiger Team Assessment of the Idaho National Engineering Laboratory (INEL) located in Idaho Falls, Idaho. INEL is a multiprogram, laboratory site of the US Department of Energy (DOE). Overall site management is provided by the DOE Field Office, Idaho; however, the DOE Field Office, Chicago has responsibility for the Argonne National Laboratory-West facilities and operations through the Argonne Area Office. In addition, the Idaho Branch Office of the Pittsburgh Naval Reactors Office has responsibility for the Naval Reactor Facility (NRF) at the INEL. The assessment included all DOE elements having ongoing program activities at the site except for the NRF. In addition, the Safety and Health Subteam did not review the Westinghouse Idaho Nuclear Company, Inc. facilities and operations. The Tiger Team Assessment was conducted from June 17 to August 2, 1991, under the auspices of the Office of Special Projects, Office of the Assistant Secretary for Environment, Safety and Health, Headquarters, DOE. The assessment was comprehensive, encompassing environmental, safety, and health (ES H) disciplines; management; and contractor and DOE self-assessments. Compliance with applicable federal, state, and local regulations; applicable DOE Orders; best management practices; and internal INEL site requirements was assessed. In addition, an evaluation of the adequacy and effectiveness of the DOE and the site contractors management of ES H/quality assurance programs was conducted.

Tiger Team assessment of the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

1991-08-01

The purpose of the Safety and Health (S ampersand H) Subteam assessment was to determine the effectiveness of representative safety and health programs at the Idaho National Engineering Laboratory (INEL) site. Four Technical Safety Appraisal (TSA) Teams were assembled for this purpose by the US Department of Energy (DOE), Deputy Assistant Secretary for Safety and Quality Assurance, Office of Safety Appraisals (OSA). Team No. 1 reviewed EG ampersand G Idaho, Inc. (EG ampersand G Idaho) and the Department of Energy Field Office, Idaho (ID) Fire Department. Team No. 2 reviewed Argonne National Laboratory-West (ANL-W). Team No. 3 reviewed selected contractors at the INEL; specifically, Morrison Knudsen-Ferguson of Idaho Company (MK-FIC), Protection Technology of Idaho, Inc. (PTI), Radiological and Environmental Sciences Laboratory (RESL), and Rockwell-INEL. Team No. 4 provided an Occupational Safety and Health Act (OSHA)-type compliance sitewide assessment of INEL. The S ampersand H Subteam assessment was performed concurrently with assessments conducted by Environmental and Management Subteams. Performance was appraised in the following technical areas: Organization and Administration, Quality Verification, Operations, Maintenance, Training and Certification, Auxiliary Systems, Emergency Preparedness, Technical Support, Packaging and Transportation, Nuclear Criticality Safety, Security/Safety Interface, Experimental Activities, Site/Facility Safety Review, Radiological Protection, Personnel Protection, Worker Safety and Health (OSHA) Compliance, Fire Protection, Aviation Safety, Medical Services, and Firearms Safety

Software process improvement in the NASA software engineering laboratory

Science.gov (United States)

Mcgarry, Frank; Pajerski, Rose; Page, Gerald; Waligora, Sharon; Basili, Victor; Zelkowitz, Marvin

1994-01-01

The Software Engineering Laboratory (SEL) was established in 1976 for the purpose of studying and measuring software processes with the intent of identifying improvements that could be applied to the production of ground support software within the Flight Dynamics Division (FDD) at the National Aeronautics and Space Administration (NASA)/Goddard Space Flight Center (GSFC). The SEL has three member organizations: NASA/GSFC, the University of Maryland, and Computer Sciences Corporation (CSC). The concept of process improvement within the SEL focuses on the continual understanding of both process and product as well as goal-driven experimentation and analysis of process change within a production environment.

Mixed waste treatment at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Larsen, M.M.; Hunt, L.F.; Sanow, D.J.

1988-01-01

The Idaho Operations Office of the Department of Energy (DOE) made the decision in 1984 to prohibit the disposal of mixed waste (MW) (combustible waste-toxic metal waste) in the Idaho National Engineering Laboratory (INEL) low-level radioactive waste (LLW) disposal facility. As a result of this decision and due to there being no EPA-permitted MW treatment/storage/disposal (T/S/D) facilities, the development of waste treatment methods for MW was initiated and a storage facility was established to store these wastes while awaiting development of treatment systems. This report discusses the treatment systems developed and their status. 3 refs., 2 figs., 1 tab

Cost-effectiveness of annual versus biennial screening mammography for women with high mammographic breast density.

Science.gov (United States)

Pataky, Reka; Ismail, Zahra; Coldman, Andrew J; Elwood, Mark; Gelmon, Karen; Hedden, Lindsay; Hislop, Greg; Kan, Lisa; McCoy, Bonnie; Olivotto, Ivo A; Peacock, Stuart

2014-12-01

The sensitivity of screening mammography is much lower among women who have dense breast tissue, compared with women who have largely fatty breasts, and they are also at much higher risk of developing the disease. Increasing mammography screening frequency from biennially to annually has been suggested as a policy option to address the elevated risk in this population. The purpose of this study was to assess the cost-effectiveness of annual versus biennial screening mammography among women aged 50-79 with dense breast tissue. A Markov model was constructed based on screening, diagnostic, and treatment pathways for the population-based screening and cancer care programme in British Columbia, Canada. Model probabilities and screening costs were calculated from screening programme data. Costs for breast cancer treatment were calculated from treatment data, and utility values were obtained from the literature. Incremental cost-effectiveness was expressed as cost per quality adjusted life year (QALY), and probabilistic sensitivity analysis was conducted. Compared with biennial screening, annual screening generated an additional 0.0014 QALYs (95% CI: -0.0480-0.0359) at a cost of $819 ($ = Canadian dollars) per patient (95% CI: 506-1185), resulting in an incremental cost effectiveness ratio of $565,912/QALY. Annual screening had a 37.5% probability of being cost-effective at a willingness-to-pay threshold of $100,000/QALY. There is considerable uncertainty about the incremental cost-effectiveness of annual mammography. Further research on the comparative effectiveness of screening strategies for women with high mammographic breast density is warranted, particularly as digital mammography and density measurement become more widespread, before cost-effectiveness can be reevaluated. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

METHODICS, SOFTWARE AND LABORATORY EQUIPMENT FOR AN INNOVATIVE ELECTRICAL ENGINEERING DISCIPLINE

Directory of Open Access Journals (Sweden)

V.S. Petrushin

2016-09-01

Full Text Available Purpose. Development of innovative electrical engineering discipline «Electric Machines in Mechatronic Systems» in order to improve the training of specialists of electrical engineering specialty. Methodology. The proposed project concerns the educational reforms that promote the intensification of the educational process. Results. The structure of interactive educational and training complex, which is a computer learning tool in the form of software and methodical support, as well as data and knowledge bases and consists of functionally related multimedia learning systems, interactive learning, automated control of the learning process. Originality. To offer online training and research facilities, guidelines for laboratory and computational and graphic works. Practical value. Increase the knowledge of students of educational material related to the discipline of innovation «Electric Machines in Mechatronic Systems».

Technology and use of lignite. Proceedings of the tenth biennial lignite symposium

Energy Technology Data Exchange (ETDEWEB)

Kube, W. R.; Gronhovd, G. H. [comps.

1979-01-01

The symposium on the technology and use of lignite was sponsored by the US Department of Energy and the University of North Dakota, and held at Grand Forks, North Dakota, May 30-31, 1979. Twenty-one papers from the proceedings of this tenth biennial lignite symposium have been entered into EDB and ERA and three also into EAPA. The papers discuss lignite deposits in the USA, mining plans, gasification and in-situ gasification, and combustion in fossil-fuel power plants. (LTN)

Laboratory Evaluation of In Situ Chemical Oxidation for Groundwater Remediation, Test Area North, Operable Unit 1-07B, Idaho National Engineering and Environmental Laboratory, Volume Three - Appendix F

Energy Technology Data Exchange (ETDEWEB)

Cline, S.R.; Denton, D.L.; Giaquinto, J.M.; McCracken, M.K.; Starr, R.C.

1999-04-01

This appendix supports the results and discussion of the laboratory work performed to evaluate the feasibility of in situ chemical oxidation for Idaho National Environmental and Engineering Laboratory's (INEEL) Test Area North (TAN) which is contained in ORNL/TM-13711/V1. This volume contains Appendix F. Appendix F is essentially a photocopy of the ORNL researchers' laboratory notebooks from the Environmental Sciences Division (ESD) and the Radioactive Materials Analytical Laboratory (RMAL).

Annual report of Radiation Laboratory Department of Nuclear Engineering Kyoto University for fiscal 1993

International Nuclear Information System (INIS)

1994-07-01

This publication is the collection of the papers presented research activities of Radiation Laboratory, Department of Nuclear Engineering, Kyoto University during the 1993 academic/fiscal year (April, 1993 - March, 1994). The 47 of the presented papers are indexed individually. (J.P.N.)

TREE CANOPY PRUNING DOES NOT REGULATE BIENNIAL BEARING IN ”ELSTAR” APPLE (Malus domestica Borkh.

Directory of Open Access Journals (Sweden)

Nikola Pavičić

2004-12-01

Full Text Available Four alternative pruning strategies (A– 25 generative buds, B– 50 generative buds, C– 75 generative buds and D–100 generative buds per tree for Elstar apple cultivar and their possible impact on improvement in productivity were examined in 1999 and 2000. Year was significant factor for all traits, except yield. The pruning strategy is significant for number of fruits per flower cluster and fruit mass. Interaction year and pruning strategy is significant only for number of fruits per flower cluster. Fruit mass was larger for pruning strategy A compared to the pruning strategies C and D. Yield efficiency and biennial bearing index were not affected by pruning strategies. The biennial bearing index variance was the lowest for the pruning strategy B. Trunk cross sectional area (TCSA had negative impact on fruit mass in pruning strategy C. Correlation between the flower and crop density was positive in pruning strategy A. Flower density was in positive correlation with yield in pruning strategy C. The research shows that tree pruning alone will not result in adequate yield regulation in ‘Elstar’ apple.

Biennial activity report of Metallurgy Division for 1989 and 1990

Energy Technology Data Exchange (ETDEWEB)

Kamachi Mudali, U; Muraleedharan, P; Parameswaran, P; Swaminathan, K; Sreedharan, O M [eds.; Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

1994-12-31

This is the first divisional biennial report of the Metallurgy Division of Indira Gandhi Centre for Atomic Research, for the year 1989-1990, after formation of the Metallurgy Division in September 1988. Major areas of work in the Division relate to aqueous corrosion and localised corrosion, stress corrosion cracking and liquid metal corrosion, high temperature oxidation, thermodynamic studies, physical metallurgy studies for structure-property correlations and failure analyses. The principal materials of studies have been the austenitic stainless steels, the current materials of construction in the Fast Breeder Test Reactor and the candidate materials for the Prototype Fast Breeder Reactor 7 figs., 6 tabs., 2 ills.

The Engineering of LISA Pathfinder – the quietest Laboratory ever flown in Space

International Nuclear Information System (INIS)

Trenkel, Christian; Wealthy, Dave; Dunbar, Neil; Warren, Carl; Schleicher, Alexander; Ziegler, Tobias; Brandt, Nico; Gerndt, Rüdiger

2017-01-01

We review the engineering approach adopted to ensure the required gravitational, magnetic, thermal and residual acceleration stability on-board LISA Pathfinder, and present the in-flight results that have been achieved. Arguably, this stability makes LISA Pathfinder the quietest laboratory ever flown in space. The implications for LISA are also discussed. (paper)

Radiochemistry Programme biennial progress report 1984 and 1985

International Nuclear Information System (INIS)

1986-01-01

This biennial progress report of the Radiochemistry Programme covers the calendar years 1984 and 1985. This report is organised into sections in a manner similar to the organisation of the Radiochemistry Programme. Thus the section on Fuel Behaviour Studies include post-irradiation studies (where the emphasis has been on setting up of facilities), mass spectrometry an nuclear chemistry. Process Chemistry Section covers the activities relating to fuel reprocessing as well as preparation and characterisation of fuel materials. Solid State Chemistry Section deals with thermophysical properties, thermogravimetry, oxygen potentials etc. In the Sodium Chemistry Section the developments relating to on-line meters and their applications are stressed in addition to studies on ternary systems involving sodium and oxygen. Developments in analytical chemistry and analytical services are covered in the next two Sections. Technical Services Section deals with developments in instrumentation and mechanical fabrication. (author)

Quality assurance on the Idaho National Engineering Laboratory Buried Waste Program

International Nuclear Information System (INIS)

Rasmussen, T.L.

1989-01-01

This paper discusses the clean-up of an Idaho National Engineering Laboratory (INEL) site utilized for disposal of transuranic contaminated waste from 1954 until 1970. The author presents requirements of the environmental protection statutes that have generated quality assurance requirements in addition to those historically implemented as a part of facility design, construction and operation. A hierarchy of program guidance quality documentation and procedures is discussed. Data qualification and computer database management are identified as requirements

Biennial activity report of Metallurgy Programme - 1985 and 1986

International Nuclear Information System (INIS)

Mallika, C.; Sreenivasan, P.R.; Muraleedharan, P.; Shyamsunder, M.T.; Kuppuswami, P.; Sampath, N.; Bhaduri, A.K.; Sreedharan, O.M.

1988-01-01

The biennial activity report of the Metallurgy Programme of the Indira Gandhi Centre for Atomic Research covers the period of the years 1985 and 1986. Along with NDT, welding metallurgy, low cycle fatigue, creep and creep fatigue interactions, structure-property correlations, thermodynamics and corrosion metallurgy of alloy steels with respect to their compatibility with aqueous and liquid sodium environments continue to be the major thrust areas of the Programme. Some of the basic research contributions of the Programme are: the observation of uniform and homogeneous distribution of voids in cyclically deformed 304 SS, the role of grain boundaries and precipitation in dynamic strain ageing of 316 SS and the determination of the activities of component metals in 316 and 304 SS by metastable EMF method. (author)

Operational and engineering developments in the management of low-level radioactive waste at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Kendall, E.W.; McKinney, J.D.; Wehmann, G.

1979-01-01

The Radioactive Waste Management Complex (RWMC) of the Idaho National Engineering Laboratory is a site for shallow land disposal and storage of solid radioactive waste. It is currently operated for ERDA by EG and G Idaho, Inc. The facility has accepted radioactive waste since July 1952. Both transuranic and non-transuranic wastes are handled at the complex. This document describes the operational and engineering developments in waste handling and storage practices that have been developed during the 25 years of waste handling operations. Emphasis is placed on above-ground transuranic waste storage, subsurface transuranic waste retrieval, and beta/gamma compaction disposal. The proposed future programs for the RWMC including a Molten Salt Combustion Facility and Production Scale Retrieval Project are described

Fritz Engineering Laboratory

Data.gov (United States)

Federal Laboratory Consortium — Features 800,000 lb and 5,000,000 lb universal testing machines, and a dynamic test bed with broad fatigue-testing capabilities, and a wide range of instrumentation....

In summary: Idaho National Engineering Laboratory site environmental report for calendar year 1995

International Nuclear Information System (INIS)

Roush, D.; Mitchell, R.G.; Peterson, D.

1996-08-01

Every human is exposed to natural radiation. This exposure comes from many sources, including cosmic radiation from outer space, naturally-occurring radon, and radioactivity from substances in our bodies. In addition to natural sources of radiation, humans can also be exposed to man-made sources of radiation. Examples of man-made sources include nuclear medicine, X-rays, nuclear weapons testing, and accidents at nuclear power plants. The Idaho National Engineering Laboratory (INEL) is a U.S. Department of Energy (DOE) research facility that deals, in part, with studying nuclear reactors and storing radioactive materials. Careful handling and rigorous procedures do not completely eliminate the risk of releasing radioactivity. So, there is a remote possibility for a member of the public near the INEL to be exposed to radioactivity from the INEL. Extensive monitoring of the environment takes place on and around the INEL. These programs search for radionuclides and other contaminants. The results of these programs are presented each year in a site environmental report. This document summarizes the Idaho National Engineering Laboratory Site Environmental Report for Calendar Year 1995

Reducing the number of laboratory animals used in tissue engineering research by restricting the variety of animal models. Articular cartilage tissue engineering as a case study.

Science.gov (United States)

de Vries, Rob B M; Buma, Pieter; Leenaars, Marlies; Ritskes-Hoitinga, Merel; Gordijn, Bert

2012-12-01

The use of laboratory animals in tissue engineering research is an important underexposed ethical issue. Several ethical questions may be raised about this use of animals. This article focuses on the possibilities of reducing the number of animals used. Given that there is considerable debate about the adequacy of the current animal models in tissue engineering research, we investigate whether it is possible to reduce the number of laboratory animals by selecting and using only those models that have greatest predictive value for future clinical application of the tissue engineered product. The field of articular cartilage tissue engineering is used as a case study. Based on a study of the scientific literature and interviews with leading experts in the field, an overview is provided of the animal models used and the advantages and disadvantages of each model, particularly in terms of extrapolation to the human situation. Starting from this overview, it is shown that, by skipping the small models and using only one large preclinical model, it is indeed possible to restrict the number of animal models, thereby reducing the number of laboratory animals used. Moreover, it is argued that the selection of animal models should become more evidence based and that researchers should seize more opportunities to choose or create characteristics in the animal models that increase their predictive value.

Testing a tri-partite contingent model of engineering cultures: A pilot study

International Nuclear Information System (INIS)

Murphy, Glen D.

2010-01-01

For some time there has been a growing awareness of organizational culture and its impact on the functioning of engineering and maintenance departments. Those wishing to implement contemporary maintenance regimes (e.g. condition based maintenance) are often encouraged to develop 'appropriate cultures' to support a new method's introduction. Unfortunately these same publications often fail to specifically articulate the cultural values required to support those efforts. In the broader literature, only a limited number of case examples document the cultural values held by engineering asset intensive firms and how they contribute to their success (or failure). Consequently a gap exists in our knowledge of what engineering cultures currently might look like, or what might constitute a best practice engineering asset culture. The findings of a pilot study investigating the perceived ideal characteristics of engineering asset cultures are reported. Engineering managers, consultants and academics (n=47), were surveyed as to what they saw were essential attributes of both engineering cultures and engineering asset personnel. Valued cultural elements included those orientated around continuous improvement, safety and quality. Valued individual attributes included openness to change, interpersonal skills and conscientiousness. The paper concludes with a discussion regarding the development of a best practice cultural framework for practitioners and engineering managers.

Can Australian radiographers assess screening mammograms accurately? Biennial follow-up from a four year prospective study and lesion analysis

International Nuclear Information System (INIS)

Moran, S.; Warren-Forward, H.

2016-01-01

Introduction: Globally, the role of the radiographer is changing; some countries have developed advanced roles with specific scopes of practice. Other countries, like Australia, are in the process of this change. This paper demonstrates the abilities of Australian radiographers in mammogram screen reading, highlighting some of their specific difficulties with different lesion types. Method: Six experienced radiographers participated in a prospective study, screen reading 2000 mammograms each between 2010 and 2011. This paper looks at the results of those same women at biennial re-screen. Analysis of the results included validation of normal results by negative follow-up screens and new cancers at biennial review; there is also analysis on the types of lesions detected and missed. Results: After biennial review, three cancers in 2013/2014 had been marked as abnormal by one radiographer two years prior, which increased her sensitivity from 64% to 85%. Sensitivity for the radiologists decreased from the assumed 100% to 95%. Radiographers appeared to be skilled in detection of calcifications and architectural distortions but had difficulty with non-specific densities. Conclusion: This study demonstrates the potential for Australian radiographers to enhance the accuracy of screen reading programs. - Highlights: • Radiographers have the potential to increase breast cancer detection rates. • Radiographers appear to be skilled at detecting calcifications. • Lesions commonly overlooked by radiographers could be targeted for training.

Environmental Management Plan for the Chemical Engineering Laboratory (LIQ) of the National University of Colombia, Bogotá

OpenAIRE

Javier Gama Chávez; Martha Lozano García; Paulo César Narváez Rincón; Óscar Javier Suárez Medina

2004-01-01

An Enviromental Management Plan was formulated with the objective of improving the environmental performance of the Chemical Engineering Laboratory (LIQ). The plan was supported on the principles established by the ISO 140001 standard. In a first step, an environmental politic was proposed. Next, by means of an initial review of the laboratory, the most significant impacts related to the activities developed in the Laboratory were identified: dangerous chemical wastes accumulation, water cont...

Building an integrated nuclear engineering and nuclear science human resources pipeline at the Idaho National Engineering and Environmental Laboratory

International Nuclear Information System (INIS)

Sneed, A.; Sikorski, B.; Lineberry, M.; Jolly, J.

2004-01-01

In a joint effort with the Argonne National Laboratory - West (ANL-W), the Idaho National Engineering and Environmental Laboratory (INEEL) has assumed the lead role for nuclear energy reactor research for the United States Government. In 2005, these two laboratories will be combined into one entity, the Idaho National Laboratory (INL). There are two objectives for the INL: (1) to act as the lead systems integrator for the Department of Energy's Office of Nuclear Energy Science and Technology and, (2) to establish a Center for Advanced Energy Studies. Focusing on the Center for Advanced Energy Studies, this paper presents a Human Resources Pipeline Model outlining a nuclear educational pathway that leads to university and industry research partnerships. The pathway progresses from education to employment and into retirement. Key to the model is research and mentoring and their impact upon each stage. The Center's success will be the result of effective and advanced communications, faculty/student involvement, industry support, inclusive broadbased involvement, effective long-term partnering, and increased federal and state support. (author)

Research Summaries: The 11th Biennial Rivkin Center Ovarian Cancer Research Symposium.

Science.gov (United States)

Armstrong, Deborah K

2017-11-01

In September 2016, the 11th biennial ovarian cancer research symposium was presented by the Rivkin Center for Ovarian Cancer and the American Association for Cancer Research. The 2016 symposium focused on 4 broad areas of research: Mechanisms of Initiation and Progression of Ovarian Cancer, Tumor Microenvironment and Models of Ovarian Cancer, Detection and Prevention of Ovarian Cancer, and Novel Therapeutics for Ovarian Cancer. The presentations and abstracts from each of these areas are reviewed in this supplement to the International Journal of Gynecologic Oncology.

Coronary Heart Disease Knowledge and Risk Factors among Tri-Ethnic College Students

Science.gov (United States)

Koutoubi, Samer; Huffman, Fatma G.; Ciccazzo, Michele W.; Himburg, Susan P.; Johnson, Paulette

2005-01-01

Objectives: Coronary heart disease (CHD) is the leading cause of death in the United States and Europe. This study identified and compared nutritional knowledge associated with CHD risk factors among tri-ethnic college students. Design: A quantitative, cross-sectional, observational study using questionnaires. Setting: University laboratory.…

Lawrence Berkeley laboratory neutral-beam engineering test facility power-supply system

International Nuclear Information System (INIS)

Lutz, I.C.; Arthur, C.A.; deVries, G.J.; Owren, H.M.

1981-10-01

The Lawrence Berkeley Laboratory is upgrading the neutral beam source test facility (NBSTF) into a neutral beam engineering test facility (NBETF) with increased capabilities for the development of neutral beam systems. The NBETF will have an accel power supply capable of 170 kV, 70 A, 30 sec pulse length, 10% duty cycle; and the auxiliary power supplies required for the sources. This paper describes the major components, their ratings and capabilities, and the flexibility designed to accomodate the needs of source development

Interactive virtual laboratory for distance education in nuclear engineering

International Nuclear Information System (INIS)

Jain, P.; Stubbins, J.; Uddin, R.

2006-01-01

A real time, distance lab module is being developed and implemented in the Dept. of Nuclear, Plasma and Radiological Engineering at the Univ. of Illinois at Urbana-Champaign. This internet based system allows remote personnel to watch the experiments, acquire data, and interact with on-site personnel. The e-lab broadcasts not only the live scenes of laboratory and experiments, but also the real time data and plots being measured and displayed in graphical and other formats. Moreover, use of LabVIEW's remote front panel feature allows communications between the local lab and remote client so that, if permitted, remote client can control part or all of the experiment in real-time. (authors)

Formal training program for nuclear material custodians at Hanford Engineering Development Laboratory

International Nuclear Information System (INIS)

Scott, D.D.

1979-01-01

Hanford Engineering Development Laboratory (HEDL) has established a formal training program for nuclear material (NM) custodians. The program, designed to familiarize the custodian with the fundamental concepts of proper nuclear materials control and accountability, is conducted on a semiannual basis. The program is prepared and presented by the Safeguards and Materials Management Section of HEDL and covers 14 subjects on accountability, documentation, transportation, custodian responsibilities, and the safeguarding of nuclear material

Closing the loop on improvement: Packaging experience in the Software Engineering Laboratory

Science.gov (United States)

Waligora, Sharon R.; Landis, Linda C.; Doland, Jerry T.

1994-01-01

As part of its award-winning software process improvement program, the Software Engineering Laboratory (SEL) has developed an effective method for packaging organizational best practices based on real project experience into useful handbooks and training courses. This paper shares the SEL's experience over the past 12 years creating and updating software process handbooks and training courses. It provides cost models and guidelines for successful experience packaging derived from SEL experience.

Design and implementation of an internet-based electrical engineering laboratory.

Science.gov (United States)

He, Zhenlei; Shen, Zhangbiao; Zhu, Shanan

2014-09-01

This paper describes an internet-based electrical engineering laboratory (IEE-Lab) with virtual and physical experiments at Zhejiang University. In order to synthesize the advantages of both experiment styles, the IEE-Lab is come up with Client/Server/Application framework and combines the virtual and physical experiments. The design and workflow of IEE-Lab are introduced. The analog electronic experiment is taken as an example to show Flex plug-in design, data communication based on XML (Extensible Markup Language), experiment simulation modeled by Modelica and control terminals' design. Crown Copyright © 2014. Published by Elsevier Ltd. All rights reserved.

Stratospheric Aerosol and Gas Experiment II measurements of the quasi-biennial oscillations in ozone and nitrogen dioxide

Science.gov (United States)

Zawodny, Joseph M.; Mccormick, M. P.

1991-01-01

The first measurements ever to show a quasi-biennial oscillation (QBO) in NO2 have been made by the Stratospheric Aerosol and Gas Experiment II) (SAGE II) and are presented in this work along with observations of the well-known QBO in stratospheric ozone. The SAGE II instrument was launched aboard the Earth Radiation Budget satellite near the end of 1984. Measurements of ozone and nitrogen dioxide through early 1990 are analyzed for the presence of a quasi-biennial oscillation. The measurements show the global extent of both the O3 and NO2 QBO in the 25- to 40-km region of the stratosphere. The SAGE II QBO results for ozone compare favorably to theory and previous measurements. The QBO in NO2 is found to be consistent with the vertical and horizontal transport of NOy. Both species exhibit a QBO at extratropical latitudes consistent with strong meridional transport into the winter hemisphere.

Optical Beam Deflection Based AFM with Integrated Hardware and Software Platform for an Undergraduate Engineering Laboratory

Directory of Open Access Journals (Sweden)

Siu Hong Loh

2017-02-01

Full Text Available Atomic force microscopy (AFM has been used extensively in nanoscience research since its invention. Recently, many teaching laboratories in colleges, undergraduate institutions, and even high schools incorporate AFM as an effective teaching tool for nanoscience education. This paper presents an optical beam deflection (OBD based atomic force microscope, designed specifically for the undergraduate engineering laboratory as a teaching instrument. An electronic module for signal conditioning was built with components that are commonly available in an undergraduate electronic laboratory. In addition to off-the-shelf mechanical parts and optics, the design of custom-built mechanical parts waskept as simple as possible. Hence, the overall cost for the setup is greatly reduced. The AFM controller was developed using National Instruments Educational Laboratory Virtual Instrumentation Suite (NI ELVIS, an integrated hardware and software platform which can be programmed in LabVIEW. A simple yet effective control algorithm for scanning and feedback control was developed. Despite the use of an educational platform and low-cost components from the undergraduate laboratory, the developed AFM is capable of performing imaging in constant-force mode with submicron resolution and at reasonable scanning speed (approximately 18 min per image. Therefore, the AFM is suitable to be used as an educational tool for nanoscience. Moreover, the construction of the system can be a valuable educational experience for electronic and mechanical engineering students.

Pollution prevention for cleaner air: EPA's air and energy engineering research laboratory

International Nuclear Information System (INIS)

Shaver, E.M.

1992-01-01

The article discusses the role of EPA's Air and Energy Engineering Research Laboratory (AEERL) in pollution prevention research for cleaner air. For more than 20 years, AEERL has been conducting research to identify control approaches for the pollutants and sources which contribute to air quality problems. The Laboratory has successfully developed and demonstrated cost-effective sulfur dioxide, nitrogen oxides, and particulate control technologies for fossil fuel combustion sources. More recently, it has expanded its research activities to include indoor air quality, radon, organic control, stratospheric ozone depletion, and global warming. AEERL also develops inventories of air emissions of many types. Over the last several years, it has made substantial efforts to expand research on pollution prevention as the preferred choice for air emissions reduction

On the development of the theory of the QBO. [Quasi-Biennial Oscillation

Science.gov (United States)

Lindzen, Richard S.

1987-01-01

The events that led to the discovery of the quasi-biennial oscillation (QBO) of the equatorial stratosphere are described together with the development of current QBO theory. Three independent areas of inquiry led to this theory: (1) the observational and theoretical studies of equatorial waves, (2) the theoretical study of the behavior of mountain waves at critical levels where the mean flow speed went to zero, and (3) the semiempirical study of the momentum budget of the QBO. The efforts in each of these three areas are discussed.

Interdecadal variability of the tropospheric biennial oscillation in the western North Pacific

International Nuclear Information System (INIS)

Zheng Bin; Lin Ailan; Gu Dejun; Li Chunhui

2008-01-01

The observed tropospheric biennial oscillation (TBO) in the western North Pacific (WNP) monsoon region has an interdecadal variability with a period of 40–50 yr. That suggests a weaker effect of the TBO on the East Asia followed by a stronger one. A simple analytic model was designed to investigate the mechanism of the interdecadal variability of the TBO. The results indicated that a local TBO air-sea system not only supports the TBO variability in the WNP monsoon region but also produces an interdecadal variability of the TBO

TECHNOLOGICAL COMPETENCE OF FUTURE ENGINEER: FORMATION AND DEVELOPMENT IN COMPUTER INTEGRATED LABORATORY WORKSHOP ON PHYSICS

Directory of Open Access Journals (Sweden)

Ihor S. Chernetskyi

2013-12-01

Full Text Available The article examines the category «technological competence» and the definition of its components according to the educational process. A structural and functional model of technological competence of future engineers through forms, means, methods and technologies of computer oriented laboratory work. Selected blocks and elements of the model in the course of a typical student laboratory work on the course of general physics. We consider the possibility of using some type of digital labs «Phywe», «Fourier» and modern electronic media (flash books to optimize laboratory work at the Technical University. The analysis of the future research of structural elements model of technological competence.

College of Engineering & Applied Science

Science.gov (United States)

Computational Mechanics Laboratory Environmental Engineering Laboratory Geotechnical Engineering Laboratory Engineering Concentration on Ergonomics M.S. Program in Computer Science Interdisciplinary Concentration on Energy Doctoral Programs in Engineering Non-Degree Candidate Departments Biomedical Engineering

Chemical Engineering in the "BIO" World.

Science.gov (United States)

Chiarappa, Gianluca; Grassi, Mario; Abrami, Michela; Abbiati, Roberto Andrea; Barba, Anna Angela; Boisen, Anja; Brucato, Valerio; Ghersi, Giulio; Caccavo, Diego; Cascone, Sara; Caserta, Sergio; Elvassore, Nicola; Giomo, Monica; Guido, Stefano; Lamberti, Gaetano; Larobina, Domenico; Manca, Davide; Marizza, Paolo; Tomaiuolo, Giovanna; Grassi, Gabriele

2017-01-01

Modern Chemical Engineering was born around the end of the 19th century in Great Britain, Germany, and the USA, the most industrialized countries at that time. Milton C. Whitaker, in 1914, affirmed that the difference between Chemistry and Chemical Engineering lies in the capability of chemical engineers to transfer laboratory findings to the industrial level. Since then, Chemical Engineering underwent huge transformations determining the detachment from the original Chemistry nest. The beginning of the sixties of the 20th century saw the development of a new branch of Chemical Engineering baptized Biomedical Engineering by Peppas and Langer and that now we can name Biological Engineering. Interestingly, although Biological Engineering focused on completely different topics from Chemical Engineering ones, it resorted to the same theoretical tools such as, for instance, mass, energy and momentum balances. Thus, the birth of Biological Engineering may be considered as a Darwinian evolution of Chemical Engineering similar to that experienced by mammals which, returning to water, used legs and arms to swim. From 1960 on, Biological Engineering underwent a considerable evolution as witnessed by the great variety of topics covered such as hemodialysis, release of synthetic drugs, artificial organs and, more recently, delivery of small interfering RNAs (siRNA). This review, based on the activities developed in the frame of our PRIN 2010-11 (20109PLMH2) project, tries to recount origins and evolution of Chemical Engineering illustrating several examples of recent and successful applications in the biological field. This, in turn, may stimulate the discussion about the Chemical Engineering students curriculum studiorum update. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

CONTEMPORARY ART EVENTS IN TOURISM: THE CASE OF INTERNATIONAL ISTANBUL BIENNALE

Directory of Open Access Journals (Sweden)

Nazmi EROGLU,

2017-02-01

Full Text Available Known as a contemporary art event of the biennial is organized every two years and mostly take the name from host city. The name of biennial used firstly in Venice and it was organized first time in Venice as Venice Biennial. Biennials accessed to many cities of the world and has provided economic contributions except of the social and cultural contributions for the city. International Istanbul Biennial that organized since 1987 in Turkey is not known and realized enough in terms of contribution and potential in Turkey. Especially paying attention to provided and providing contribution of biennials are necessary in tourism field. In the research biennials were examined on the field of event tourism as contemporary art events. Also in this research tourism were associated and classified with biennials in the framework of literature. Making assessment about contemporary art events in tourism is made with example of İnternational İstanbul Biennials in Turkey. Some examples and suggestions were tried to give for understanding potential of contemporary art events in tourism and relationship between biennials and tourism. In addition, information is given about biennials that are at international level. The main purpose of the research is that paying attention to benefits which is provided and possible from İnternational Istanbul Biennial and emphasized to importance of event tourism in Turkey.

Idaho National Engineering Laboratory installation roadmap document. Revision 1

Energy Technology Data Exchange (ETDEWEB)

1993-05-30

The roadmapping process was initiated by the US Department of Energy`s office of Environmental Restoration and Waste Management (EM) to improve its Five-Year Plan and budget allocation process. Roadmap documents will provide the technical baseline for this planning process and help EM develop more effective strategies and program plans for achieving its long-term goals. This document is a composite of roadmap assumptions and issues developed for the Idaho National Engineering Laboratory (INEL) by US Department of Energy Idaho Field Office and subcontractor personnel. The installation roadmap discusses activities, issues, and installation commitments that affect waste management and environmental restoration activities at the INEL. The High-Level Waste, Land Disposal Restriction, and Environmental Restoration Roadmaps are also included.

Idaho National Engineering Laboratory irradiation facilities and their applications

International Nuclear Information System (INIS)

Gupta, V.P.; Herring, J.S.; Korenke, R.E.; Harker, Y.D.

1986-05-01

Although there is a growing need for neutron and gamma irradiation by governmental and industrial organizations in the United States and in other countries, the number of facilities providing such irradiations are limited. At the Idaho National Engineering Laboratory, there are several unique irradiation facilities producing high neutron and gamma radiation environments. These facilities could be readily used for nuclear research, materials testing, radiation hardening studies on electronic components/circuitry and sensors, and production of neutron transmutation doped (NTD) silicon and special radioisotopes. In addition, a neutron radiography unit, suitable for examining irradiated materials and assemblies, is also available. This report provides a description of the irradiation facilities and the neutron radiography unit as well as examples of their unique applications

Idaho National Engineering Laboratory historical dose evaluation: Volume 1

International Nuclear Information System (INIS)

Francis, S.J.

1991-08-01

The methodology and results are presented for an evaluation of potential radiation doses to a hypothetical individual who may have resided at an offsite location with the highest concentration of airborne radionuclides near the Idaho National Engineering Laboratory (INEL). Volume 1 contains a summary of methods and results. The years of INEL operations from 1952 to 1989 were evaluated. Radiation doses to an adult, child, and infant were estimated for both operational (annual) and episodic (short-term) airborne releases from INEL facilities. Atmospheric dispersion of operational releases was modeled using annual average meteorological conditions. Dispersion of episodic releases was generally modeled using actual hourly wind speed and direction data at the time of release. 50 refs., 23 figs., 10 tabs

Numerical simulations on increasing turbojet engines exhaust mixture ratio using fluidic chevrons

Directory of Open Access Journals (Sweden)

Adrian GRUZEA

2017-06-01

Full Text Available This paper refers to some aspects regarding the terms “chevron” and “fluidic chevron” and to the process of increasing the jet engines exhaust mixing rate towards achieving noise reduction. One of the noise reduction methods consists in covering the high velocity main flow with a secondary one, having a much lower velocity, similar to the turbofan engines. The fluidic chevrons try to accomplish these requirements, being used just in particular moments of the flight. This study will be based on numerical simulations carried using the commercial software ANSYS. The geometry used will the based on the micro jet engine JetCat P80, equipping the turbines laboratory from the Faculty of Aerospace Engineering. A research based on the measured geometric, gasodynamic and cinematic parameters will be carried varying the mass flow and keeping the immersion angle constant. As a result of these simulations we’ll observe the influence of the mentioned parameters on the jet’s flow field.

Annual report 2004. Laboratory of Energy Engineering and Environmental Protection

Energy Technology Data Exchange (ETDEWEB)

Saeed, L.; Zevenhoven, R. (eds.)

2005-07-01

This fifth annual report in this series, covering year 2004, gives an overview of the research, education and other activities of the Laboratory of Energy Engineering and Environmental Protection at Helsinki University of Technology. From the research point of view, the laboratory continues in the Nordic Energy Research Program (2003-2006) in the field of CO{sub 2} capture and storage, and in the EU project 'ToMeRed' on toxic trace elements emissions control. The laboratory is also the operating agent for the IEA project 'Energy systems integration between society and industry'. The bulk of the research can be classified into three groups, in short: energy systems; spraying and combustion and combustion and waste treatment. This research takes mainly place in national and international consortia, but sometimes also in a direct cooperation with one industry partner. Some of the work involves the use and development of models and sub- models for the simulation and optimisation of energy systems and processes. Commercial softwares like Aspen Plus and Prosim are important tools for our work as well. Besides this, single particle modelling can be applied to fuel droplets, fuel particles or particles found in metallurgical industry. We make CFD calculations with commercial codes are made as well, while working on the improvement of (sub-) models for multiphase fluid dynamics.

Engines for experiment: laboratory revolution and industrial labor in the nineteenth-century city.

Science.gov (United States)

Dierig, Sven

2003-01-01

This article brings together what until now have been separate fields of nineteenth-century history: the development of experimental physiology, the growth of mechanized industry, and the city, where their threads intertwined. The main argument is that the laboratory in the city employed the same technological and organizational approaches to modernize that the city used to industrialize. To bring the adoption of technology into focus, the article discusses laboratory research as it developed after the introduction of small-scale power engines. With its machines, the industrialized city provided not only the key metaphor of the nineteenth-century life sciences but also a key technology that shifted experimental practices in animal research from a kind of preindustrial craft to a more mechanized production of knowledge. With its "factory-laboratories," the late-nineteenth-century city became the birthplace for the first living, data-producing hybird---part animal and part machine.

State of Oregon 4th biennial energy plan

International Nuclear Information System (INIS)

Anon.

1991-01-01

State law directs the Oregon Department of Energy (ODOE) to prepare an energy plan every two years. This is the Fourth Biennial Energy Plan. The Plan is a policy blueprint for how to best meet Oregon's future energy needs. It identifies the key energy issues facing the state and sets forth policies and actions to achieve our energy goals of reliable, least-cost, and environmentally safe supply. This book presents: Oregon's demand and supply picture today. The progress Oregon has made toward energy efficiency. Oregon's energy demand and supply outlook for the next 20 years. Estimates of cost-effective conservation and other resources that could contribute to the state's energy supply. The major energy-related health, safety, and environmental issues facing the state. A strategy to reduce greenhouse gas emissions 20 percent from 1988 levels by 2005. A two-year Action Plant that spells out ODOE's recommended actions for achieving Oregon's energy goals

Air Emission Inventory for the Idaho National Engineering Laboratory, 1993 emissions report

International Nuclear Information System (INIS)

1994-06-01

This report presents the 1993 update of the Air Emission Inventory for the Idaho National Engineering Laboratory (INEL). The purpose of the Air Emission Inventory is to commence the preparation of the permit to operate application for the INEL, as required by the recently promulgated Title V regulations of the Clean Air Act. The report describes the emission inventory process and all of the sources at the INEL and provides emissions estimates for both mobile and stationary sources

Air Emission Inventory for the Idaho National Engineering Laboratory, 1993 emissions report

Energy Technology Data Exchange (ETDEWEB)

1994-06-01

This report presents the 1993 update of the Air Emission Inventory for the Idaho National Engineering Laboratory (INEL). The purpose of the Air Emission Inventory is to commence the preparation of the permit to operate application for the INEL, as required by the recently promulgated Title V regulations of the Clean Air Act. The report describes the emission inventory process and all of the sources at the INEL and provides emissions estimates for both mobile and stationary sources.

Development and application of a mobile laboratory for measuring emissions from diesel engines. 1. Regulated gaseous emissions.

Science.gov (United States)

Cocker, David R; Shah, Sandip D; Johnson, Kent; Miller, J Wayne; Norbeck, Joseph M

2004-04-01

Information about in-use emissions from diesel engines remains a critical issue for inventory development and policy design. Toward that end, we have developed and verified the first mobile laboratory that measures on-road or real-world emissions from engines at the quality level specified in the U.S. Congress Code of Federal Regulations. This unique mobile laboratory provides information on integrated and modal regulated gaseous emission rates and integrated emission rates for speciated volatile and semivolatile organic compounds and particulate matter during real-world operation. Total emissions are captured and collected from the HDD vehicle that is pulling the mobile laboratory. While primarily intended to accumulate data from HDD vehicles, it may also be used to measure emission rates from stationary diesel sources such as back-up generators. This paper describes the development of the mobile laboratory, its measurement capabilities, and the verification process and provides the first data on total capture gaseous on-road emission measurements following the California Air Resources Board (ARB) 4-mode driving cycle, the hot urban dynamometer driving schedule (UDDS), the modified 5-mode cycle, and a 53.2-mi highway chase experiment. NOx mass emission rates (g mi(-1)) for the ARB 4-mode driving cycle, the hot UDDS driving cycle, and the chase experimentwerefoundto exceed current emission factor estimates for the engine type tested by approximately 50%. It was determined that congested traffic flow as well as "off-Federal Test Procedure cycle" emissions can lead to significant increases in per mile NOx emission rates for HDD vehicles.

Analysis of Office/Laboratory Staying Hour and Home Working Hour of Japanese Scientists and Engineers

Science.gov (United States)

Ejiri, A.

The second questionnaire for scientists and engineers was carried out in 2007, and status of Japanese scientists and engineers were analyzed and reported. A part of the data was reanalyzed from the viewpoint of work life balance. In particular, office/laboratory staying hour and home working hour were analyzed and dependences on various factors were investigated. It was found that these hours depend on gender, marital status, number of child, employment status and age. In addition, the total hours tend to be kept constant regardless of various factors.

Civil Engineering in Primary Schools

Science.gov (United States)

Brown, Martin; Strong, Alan

2010-01-01

For many children of primary school age, an engineer is the man who comes to service the central heating system or who fixes the family car when it breaks down. Most have never met a "real" professional engineer, and have no idea of what is involved in the exciting world of engineering. Most assume that engineers are men. To try to…

FJ44 Turbofan Engine Test at NASA Glenn Research Center's Aero-Acoustic Propulsion Laboratory

Science.gov (United States)

Lauer, Joel T.; McAllister, Joseph; Loew, Raymond A.; Sutliff, Daniel L.; Harley, Thomas C.

2009-01-01

A Williams International FJ44-3A 3000-lb thrust class turbofan engine was tested in the NASA Glenn Research Center s Aero-Acoustic Propulsion Laboratory. This report presents the test set-up and documents the test conditions. Farfield directivity, in-duct unsteady pressures, duct mode data, and phased-array data were taken and are reported separately.

Idaho National Engineering Laboratory nonradiological waste management information for 1994 and record to date

International Nuclear Information System (INIS)

French, D.L.; Lisee, D.J.; Taylor, K.A.

1995-08-01

This document provides detailed data and graphics on airborne and liquid effluent releases, fuel oil and coal consumption, water usage, and hazardous and mixed waste generated for calendar year 1994. This report summarizes industrial waste data records compiled since 1971 for the Idaho National Engineering Laboratory (INEL). The data presented are from the INEL Nonradiological Waste Management Information System

Idaho National Engineering Laboratory Nonradiological Waste Management Information for 1993 and record to date

International Nuclear Information System (INIS)

Sims, A.M.; Taylor, K.A.

1994-08-01

This document provides detailed data and graphics on airborne and liquid effluent releases, fuel oil and coal consumption, water usage, and hazardous and mixed waste generated for calendar year 1993. This report summarizes industrial waste data records compiled since 1971 for the Idaho National Engineering Laboratory (INEL). The data presented are from the INEL Nonradiological Waste Management Information System

DOE Hydropower Program biennial report 1992--1993 (with an updated annotated bibliography)

Energy Technology Data Exchange (ETDEWEB)

Cada, G.F.; Sale, M.J. [Oak Ridge National Lab., TN (United States); Francfort, J.E.; Rinehart, B.N.; Sommers, G.L. [EG and G Idaho, Inc., Idaho Falls, ID (United States)

1993-07-01

This report, the latest in a series of annual/biennial Hydropower Program reports sponsored by the US Department of Energy, summarizes the research and development and technology transfer activities of fiscal years 1992 and 1993. The report discusses the activities in the four areas of the hydropower program: Environmental research; resource assessment; research coat shared with industry; and technology transfer. The report also offers an annotated bibliography of reports pertinent to hydropower, written by persons in Federal and state agencies, cities, metropolitan water districts, irrigation companies, and public and independent utilities. Most reports are available from the National Technical Information Service.

Expansion of the Idaho National Engineering Laboratory Research Center: Environmental assessment

International Nuclear Information System (INIS)

1994-03-01

The US Department of Energy (DOE) proposes to expand and upgrade facilities at the Idaho National Engineering Laboratory (INEL) Research Center (IRC) by constructing a research laboratory addition on the northeast corner of existing laboratory building; upgrading the fume hood system in the existing laboratory building; and constructing a hazardous waste handling facility and a chemical storage building. The DOE also proposes to expand the capabilities of biotechnology research programs by increasing use of radiolabeled compounds to levels in excess of current facility limits for three radionuclides (carbon-14, sulfur-35, and phosphorus-32). This Environmental assessment identifies the need for the new facilities, describes the proposed projects and environmental setting, and evaluates the potential environmental effects. Impacts associated with current operation are discussed and established as a baseline. Impacts associated with the proposed action and cumulative impacts are described against this background. Alternatives to the proposed action (No action; Locating proposed facilities at a different site) are discussed and a list of applicable regulations is provided. The no action alternative is continuation of existing operations at existing levels as described in Section 4 of this EA. Proposed facilities could be constructed at a different location, but these facilities would not be useful or practical since they are needed to provide a support function for IRC operations. Further, the potential environmental impacts would not be reduced if a different site was selected

PyTRiP - a toolbox and GUI for the proton/ion therapy planning system TRiP

International Nuclear Information System (INIS)

Toftegaard, J; Bassler, N; Petersen, J B

2014-01-01

Purpose: Only very few treatment planning systems (TPS) are capable of handling heavy ions. Commercial heavy ion TPS are costly and normally restrict the possibility to implement new functionalities. PyTRiP provides Python bindings and a platform-independent graphical user interface (GUI) for the heavy ion treatment program TRiP, and adds seamless support of DICOM files. We aim to provide a front-end for TRiP which does not require any special computer skills. Methods: PyTRiP is written in Python combined with C for fast computing. Routines for DICOM file import/export to TRiPs native file format are implemented. The GUI comes as an executable with all its dependencies including PyTRiP making it easy to install on Windows, Mac and Linux. Results: PyTRiP is a comprehensive toolbox for handling TRiP. Treatment plans are handled using an object oriented structure. Bindings to TRiP (which only runs on Linux, either locally or on a remote server) are performed through a single function call. GUI users can intuitively create treatment plans without much knowledge about the TRiP user interface. Advanced users still have full access to all TRiP functionality. The user interface comes with a comprehensive plotting tool, which can visualize 2D contours, volume histograms, as well as dose- and linear energy transfer (LET) distributions. Conclusion: We developed a powerful toolbox for ion therapy research using TRiP as backend. The corresponding GUI allows to easily and intuitively create, calculate and visualize treatment plans. TRiP is thereby more accessible and simpler to use.

19th Biennial International Nineteenth-Century Music Conference, Faculty of Music, University of Oxford, 11.-13. 7. 2016

Czech Academy of Sciences Publication Activity Database

Myslivcová, Eva

2016-01-01

Roč. 53, 2-3 (2016), s. 300-301 ISSN 0018-7003. [19th Biennial International Nineteenth-Century Music Conference. Oxford, 11.07.2016-13.07.2016] Institutional support: RVO:68378076 Keywords : music ological conference * nineteenth-century music * Antonin Dvorak * opera Subject RIV: AL - Art, Architecture, Cultural Heritage

Hire a Milwaukee Engineer | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Air emissions inventory for the Idaho National Engineering Laboratory -- 1995 emissions report

International Nuclear Information System (INIS)

1996-06-01

This report presents the 1995 update of the Air Emission Inventory for the Idaho National Engineering Laboratory (INEL). The INEL Air Emission Inventory documents sources and emissions of non-radionuclide pollutants from operations at the INEL. The report describes the emission inventory process and all of the sources at the INEL, and provides non-radionuclide emissions estimates for stationary sources. The air contaminants reported include nitrogen oxides, sulfur oxides, carbon monoxide, volatile organic compounds, particulates, and hazardous air pollutants (HAPs)

Air emissions inventory for the Idaho National Engineering Laboratory -- 1995 emissions report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-06-01

This report presents the 1995 update of the Air Emission Inventory for the Idaho National Engineering Laboratory (INEL). The INEL Air Emission Inventory documents sources and emissions of non-radionuclide pollutants from operations at the INEL. The report describes the emission inventory process and all of the sources at the INEL, and provides non-radionuclide emissions estimates for stationary sources. The air contaminants reported include nitrogen oxides, sulfur oxides, carbon monoxide, volatile organic compounds, particulates, and hazardous air pollutants (HAPs).

Quasi-Biennial Oscillation as the Result of Planetary Motion

Science.gov (United States)

Retejum, Alexey

QUASI-BIENNIAL OSCILLATION AS THE RESULT OF PLANETARY MOTION A.Ju.Retejum Lomonosov Moscow State University, aretejum@yandex.ru A remarkable phenomenon of quasi-biennial oscillation (QBO) attracts a growing attention for its unclear origin and possible global impact. A comprehensive theory of this phenomenon should answer the following questions: 1. Why does the phase change of the atmospheric circulation on average occur every 800 days? 2. When does the cycle length decreases or increases? 3. Wherefore the regular wind shift is observed in the equatorial stratosphere only? 4. What could cause a sudden reverse in zonal wind direction? 5. Why the generating impulse travels from the border between the atmosphere and outer space downwards without significant loss of power? 6. What is the reason of known differences in behavior patterns between west and east winds? 7. How do middle and upper latitudes respond to the remote signal? Unfortunately all the explanation of QBO that have been given so far, unable to meet the above criteria. The author proposes an alternative idea of the external forcing due to motion of Mars, Jupiter and Venus. This study is based on the QBO Index data at the 30-hPa Height for the 1979-2013 period (http://www.cpc.ncep.noaa.gov/data/indices/qbo.u30.index). Having in mind that the oscillation is symmetric about the Equator, where the Earth rotation speed is highest, one examined on the first stage relationships between the QBO manifestation and the length of day. A ten-year comparison of slow and fast spinning periods (1979-1983, 1991-1995 and 2000-2006, 2009-2011 respectively) reveals a significant difference in west and east winds strengths. The same picture can be observed if mean monthly data for March-April (the length of day maximum) and July (the length of day minimum) are collated. This is the answer to the question # 3. The exact answers to questions # 1 and # 2 give an analysis of the dependence of the wind reverse time on the moments

Evaluation of the Minnesota Easy Culture System II Bi-Plate and Tri-Plate for identification of common mastitis pathogens in milk.

Science.gov (United States)

Royster, E; Godden, S; Goulart, D; Dahlke, A; Rapnicki, P; Timmerman, J

2014-01-01

The objective of this study was to validate use of the Minnesota Easy Culture System II Bi-Plate and Tri-Plate (University of Minnesota Laboratory for Udder Health, St. Paul) to identify common mastitis pathogens in milk. A total of 283 quarter and composite milk samples submitted to the University of Minnesota Laboratory for Udder Health during the spring of 2010 were cultured simultaneously using 3 methods: standard laboratory culture (reference method) and the Minnesota Easy Culture System II Bi-Plate and Tri-Plate methods. Bi-Plate and Tri-Plate cultures were incubated for 18 to 24h and interpreted by 2 independent, untrained readers within 5h of each other. An experienced technician completed the standard laboratory culture. For each sample, all 3 study personnel recorded the culture result (yes/no) for each of the following diagnostic categories: no bacterial growth (NG), mixed (2 organisms), contaminated (3 or more organisms), gram-positive (GP), gram-negative (GN), Staphylococcus spp., Streptococcus spp., Streptococcus agalactiae, Streptococcus dysgalactiae, Streptococcus uberis, Enterococcus spp., Staphylococcus aureus, coagulase-negative staphylococci, Escherichia coli, Klebsiella spp., and other. For each category, the prevalence, sensitivity, specificity, accuracy, and predictive values of a positive and negative test were calculated, and the agreement between readers and between each reader and the laboratory was assessed. Specificity, overall accuracy, and negative predictive values were generally high (>80%) for the Bi-Plate and Tri-Plate for each category. Sensitivity and positive predictive values were intermediate (>60%) or high (>80%) for the broad categories of NG, GP, GN, Staphylococcus spp. and Streptococcus spp., and for Staph. aureus, but were generally lower (negative predictive value for Streptococcus spp., and higher interreader agreement for some of the more specific categories. Our conclusion was that Bi-Plate and Tri-Plate results will

DOE Hydropower Program Biennial Report for FY 2005-2006

Energy Technology Data Exchange (ETDEWEB)

Sale, Michael J [ORNL; Cada, Glenn F [ORNL; Acker, Thomas L. [Northern Arizona State University and National Renewable Energy Laboratory; Carlson, Thomas [Pacific Northwest National Laboratory (PNNL); Dauble, Dennis D. [Pacific Northwest National Laboratory (PNNL); Hall, Douglas G. [Idaho National Laboratory (INL)

2006-07-01

SUMMARY The U.S. Department of Energy (DOE) Hydropower Program is part of the Office of Wind and Hydropower Technologies, Office of Energy Efficiency and Renewable Energy. The Program's mission is to conduct research and development (R&D) that will increase the technical, societal, and environmental benefits of hydropower. The Department's Hydropower Program activities are conducted by its national laboratories: Idaho National Laboratory (INL) [formerly Idaho National Engineering and Environmental Laboratory], Oak Ridge National Laboratory (ORNL), Pacific Northwest National Laboratory (PNNL), and National Renewable Energy Laboratory (NREL), and by a number of industry, university, and federal research facilities. Programmatically, DOE Hydropower Program R&D activities are conducted in two areas: Technology Viability and Technology Application. The Technology Viability area has two components: (1) Advanced Hydropower Technology (Large Turbine Field Testing, Water Use Optimization, and Improved Mitigation Practices) and (2) Supporting Research and Testing (Environmental Performance Testing Methods, Computational and Physical Modeling, Instrumentation and Controls, and Environmental Analysis). The Technology Application area also has two components: (1) Systems Integration and Technology Acceptance (Hydro/Wind Integration, National Hydropower Collaborative, and Integration and Communications) and (2) Supporting Engineering and Analysis (Valuation Methods and Assessments and Characterization of Innovative Technology). This report describes the progress of the R&D conducted in FY 2005-2006 under all four program areas. Major accomplishments include the following: Conducted field testing of a Retrofit Aeration System to increase the dissolved oxygen content of water discharged from the turbines of the Osage Project in Missouri. Contributed to the installation and field testing of an advanced, minimum gap runner turbine at the Wanapum Dam project in Washington

Emulation-Based Virtual Laboratories: A Low-Cost Alternative to Physical Experiments in Control Engineering Education

Science.gov (United States)

Goodwin, G. C.; Medioli, A. M.; Sher, W.; Vlacic, L. B.; Welsh, J. S.

2011-01-01

This paper argues the case for emulation-based virtual laboratories in control engineering education. It demonstrates that such emulation experiments can give students an industrially relevant educational experience at relatively low cost. The paper also describes a particular emulation-based system that has been developed with the aim of giving…

Idaho National Engineering and Environmental Laboratory Wildland Fire Management Environmental Assessment

Energy Technology Data Exchange (ETDEWEB)

Irving, John S

2003-04-01

DOE prepared an environmental assessment (EA)for wildland fire management activities on the Idaho National Engineering and Environmental Laboratory (INEEL) (DOE/EA-1372). The EA was developed to evaluate wildland fire management options for pre-fire, fire suppression, and post fire activities. Those activities have an important role in minimizing the conversion of the native sagebrush steppe ecosystem found on the INEEL to non-native weeds. Four alternative management approaches were analyzed: Alternative 1 - maximum fire protection; Alternative 2 - balanced fire protection; Alternative 2 - balanced fire protection; Alternative 3 - protect infrastructure and personnel; and Alternative 4 - no action/traditional fire protection.

1983 Environmental monitoring program report for Idaho National Engineering Laboratory Site

International Nuclear Information System (INIS)

Hoff, D.L.; Chew, E.W.; Dickson, R.L.

1984-05-01

The results of the various monitoring programs for 1983 indicated that radioactivity from the Idaho National Engineering Laboratory (INEL) Site operations could not be distinguished from worldwide fallout and natural radioactivity in the region surrounding the Site. Although some radioactive materials were discharged during Site operations, concentrations and doses to the surrounding population were of no health consequence and were far less than State of Idaho and Federal health protection guidelines. This report describes the air, water, and foodstuff samples routinely collected at the INEL boundary locations and at locations distant from the INEL Site. 11 figures, 14 tables

Remote Laboratory NetLab for Effective Teaching of 1st Year Engineering Students

Directory of Open Access Journals (Sweden)

Z. Nedic

2007-08-01

Full Text Available Practical skills are important attributes of every engineering graduate. The Internet has provided tertiary education with the opportunity to develop innovative learning environments. The teaching and learning of practical skills has gained a new dimension with the emergence of remote laboratories. The rapidly growing number of remote laboratories (RL worldwide is the evidence that the educational community has recognized their potential to develop into a creative, flexible, engaging, and student-cantered learning environment. Even a brief review of the existing RLs shows a large diversity in their structure, design and implementation. However, not many researchers disclose how their RLs are integrated within their curricula. Therefore, an important question still remains to be answered: how to optimize the design of RLs and their integration in a course curriculum for the best learning outcomes? This problem is particularly important when RLs are used in teaching 1st year students who have limited technical knowledge and practical experience in using real equipment. In this paper we would like to share our experiences with NetLab, an RL developed at the University of South Australia (UniSA for teaching 1st year engineering students and make recommendations for improvements in teaching practices based on it.

Theory of quasi-biennial and some other oscillations in meteorological parameters

International Nuclear Information System (INIS)

Njau, E.C.

1990-11-01

We show that quasi-biennial and several other oscillations in meteorological parameters are caused by ''foldover distortions'' in the physical processes represented by the formulations contained in our recent theory. The periods of all these oscillations extend from about 50 days up to over 200,000 years. Additional oscillations within and outside this periodicity range are correspondingly generated primarily as a result of non-linearities in the earth-atmosphere system. Our analysis agrees quite well with past observations as well as results of analyses on climatic records from different locations on the earth and can, therefore, be useful in attempts to make climatic predictions as briefly indicated in the text. (author). 15 refs, 4 figs, 2 tabs

Ghana Science Association. 21st biennial conference. Program and abstracts book

International Nuclear Information System (INIS)

1999-08-01

The publication covers the program and abstracts of papers presented during the 21st biennial conference of the Ghana Science Association. The conference was held at the University of Ghana, Legon from 8th to 13th August 1999. The theme of the conference was S ustainable food Industry in Ghana in the 21st Century . The first part of the publication covers membership of various committees, list of sponsors and conference program among others. The second part is devoted to abstracts of papers presented during various scientific sessions. Papers have been grouped under the following subject areas: Biological and Medical Science, Physical Sciences, Food and Agriculture, Social Science Education and Policy Research and Poster Presentations. (E.A.)

A summary of the environmental restoration program Retrieval Demonstration Project at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

McQuary, J.

1991-01-01

This document summarizes the of retrieval techniques developed to excavate buried transuranic (TRU) mixed waste from the Subsurface Disposal Area (SDA). The SDA is located at the Idaho National Engineering Laboratory (INEL) in the Radioactive Waste Management Complex (RWMC). 31 refs., 1 fig

TRI Fotonovela Slideshow - Spanish

Science.gov (United States)

Presentation designed to introduce the basic concepts of the Toxics Release Inventory, including why TRI is an important resource for commmunities and which tool provides the easiest access to basic TRI data.

Quaternary volcanism, tectonics, and sedimentation in the Idaho National Engineering Laboratory area

Energy Technology Data Exchange (ETDEWEB)

Hackett, W.R.; Smith, R.P.

1992-09-01

In this article, we discuss the regional context and describe localities for a two-day field excursion in the vicinity of the Idaho National Engineering Laboratory (INEL). We address several geologic themes: (1) Late Cenozoic, bimodal volcanism of the Eastern Snake River Plain (ESRP), (2) the regional tectonics and structural geology of the Basin and Range province to the northwest of the ESRP, (3) fluvial, lacustrine, and aeolian sedimentation in the INEL area, and (4) the influence of Quaternary volcanism and tectonics on sedimentation near the INEL.

Quaternary volcanism, tectonics, and sedimentation in the Idaho National Engineering Laboratory area

Energy Technology Data Exchange (ETDEWEB)

Hackett, W.R.; Smith, R.P.

1992-01-01

In this article, we discuss the regional context and describe localities for a two-day field excursion in the vicinity of the Idaho National Engineering Laboratory (INEL). We address several geologic themes: (1) Late Cenozoic, bimodal volcanism of the Eastern Snake River Plain (ESRP), (2) the regional tectonics and structural geology of the Basin and Range province to the northwest of the ESRP, (3) fluvial, lacustrine, and aeolian sedimentation in the INEL area, and (4) the influence of Quaternary volcanism and tectonics on sedimentation near the INEL.

Software Engineering Laboratory (SEL) cleanroom process model

Science.gov (United States)

Green, Scott; Basili, Victor; Godfrey, Sally; Mcgarry, Frank; Pajerski, Rose; Waligora, Sharon

1991-01-01

The Software Engineering Laboratory (SEL) cleanroom process model is described. The term 'cleanroom' originates in the integrated circuit (IC) production process, where IC's are assembled in dust free 'clean rooms' to prevent the destructive effects of dust. When applying the clean room methodology to the development of software systems, the primary focus is on software defect prevention rather than defect removal. The model is based on data and analysis from previous cleanroom efforts within the SEL and is tailored to serve as a guideline in applying the methodology to future production software efforts. The phases that are part of the process model life cycle from the delivery of requirements to the start of acceptance testing are described. For each defined phase, a set of specific activities is discussed, and the appropriate data flow is described. Pertinent managerial issues, key similarities and differences between the SEL's cleanroom process model and the standard development approach used on SEL projects, and significant lessons learned from prior cleanroom projects are presented. It is intended that the process model described here will be further tailored as additional SEL cleanroom projects are analyzed.

Educating Next Generation Nuclear Criticality Safety Engineers at the Idaho National Laboratory

Energy Technology Data Exchange (ETDEWEB)

J. D. Bess; J. B. Briggs; A. S. Garcia

2011-09-01

One of the challenges in educating our next generation of nuclear safety engineers is the limitation of opportunities to receive significant experience or hands-on training prior to graduation. Such training is generally restricted to on-the-job-training before this new engineering workforce can adequately provide assessment of nuclear systems and establish safety guidelines. Participation in the International Criticality Safety Benchmark Evaluation Project (ICSBEP) and the International Reactor Physics Experiment Evaluation Project (IRPhEP) can provide students and young professionals the opportunity to gain experience and enhance critical engineering skills. The ICSBEP and IRPhEP publish annual handbooks that contain evaluations of experiments along with summarized experimental data and peer-reviewed benchmark specifications to support the validation of neutronics codes, nuclear cross-section data, and the validation of reactor designs. Participation in the benchmark process not only benefits those who use these Handbooks within the international community, but provides the individual with opportunities for professional development, networking with an international community of experts, and valuable experience to be used in future employment. Traditionally students have participated in benchmarking activities via internships at national laboratories, universities, or companies involved with the ICSBEP and IRPhEP programs. Additional programs have been developed to facilitate the nuclear education of students while participating in the benchmark projects. These programs include coordination with the Center for Space Nuclear Research (CSNR) Next Degree Program, the Collaboration with the Department of Energy Idaho Operations Office to train nuclear and criticality safety engineers, and student evaluations as the basis for their Master's thesis in nuclear engineering.

Educating Next Generation Nuclear Criticality Safety Engineers at the Idaho National Laboratory

International Nuclear Information System (INIS)

Bess, J.D.; Briggs, J.B.; Garcia, A.S.

2011-01-01

One of the challenges in educating our next generation of nuclear safety engineers is the limitation of opportunities to receive significant experience or hands-on training prior to graduation. Such training is generally restricted to on-the-job-training before this new engineering workforce can adequately provide assessment of nuclear systems and establish safety guidelines. Participation in the International Criticality Safety Benchmark Evaluation Project (ICSBEP) and the International Reactor Physics Experiment Evaluation Project (IRPhEP) can provide students and young professionals the opportunity to gain experience and enhance critical engineering skills. The ICSBEP and IRPhEP publish annual handbooks that contain evaluations of experiments along with summarized experimental data and peer-reviewed benchmark specifications to support the validation of neutronics codes, nuclear cross-section data, and the validation of reactor designs. Participation in the benchmark process not only benefits those who use these Handbooks within the international community, but provides the individual with opportunities for professional development, networking with an international community of experts, and valuable experience to be used in future employment. Traditionally students have participated in benchmarking activities via internships at national laboratories, universities, or companies involved with the ICSBEP and IRPhEP programs. Additional programs have been developed to facilitate the nuclear education of students while participating in the benchmark projects. These programs include coordination with the Center for Space Nuclear Research (CSNR) Next Degree Program, the Collaboration with the Department of Energy Idaho Operations Office to train nuclear and criticality safety engineers, and student evaluations as the basis for their Master's thesis in nuclear engineering.

Evolution of a Unique Systems Engineering Capability

Energy Technology Data Exchange (ETDEWEB)

Robert M. Caliva; James A. Murphy; Kyle B. Oswald

2011-06-01

The Idaho National Laboratory (INL) is a science-based, applied engineering laboratory dedicated to supporting U.S. Department of Energy missions in nuclear and energy research, science, and national security. The INL’s Systems Engineering organization supports all of the various programs under this wide array of missions. As with any multifaceted organization, strategic planning is essential to establishing a consistent culture and a value discipline throughout all levels of the enterprise. While an organization can pursue operational excellence, product leadership or customer intimacy, it is extremely difficult to excel or achieve best-in-class at all three. In fact, trying to do so has resulted in the demise of a number of organizations given the very intricate balancing act that is necessary. The INL’s Systems Engineering Department has chosen to focus on customer intimacy where the customer’s needs are first and foremost and a more total solution is the goal. Frequently a total solution requires the employment of specialized tools to manage system complexity. However, it is only after understanding customer needs that tool selection and use would be pursued. This results in using both commercial-off-the-shelf (COTS) tools and, in some cases, requires internal development of specialized tools. This paper describes how a unique systems engineering capability, through the development of customized tools, evolved as a result of this customer-focused culture. It also addresses the need for a common information model or analysis framework and presents an overview of the tools developed to manage and display relationships between entities, support trade studies through the application of utility theory, and facilitate the development of a technology roadmap to manage system risk and uncertainty.

The American Society for Clinical Pathology's 2015 Wage Survey of Medical Laboratories in the United States.

Science.gov (United States)

Garcia, Edna; Fisher, Patrick B

2017-05-01

To inform the pathology and laboratory field of the most recent national wage data from the American Society for Clinical Pathology (ASCP). Historically, the results of this biennial survey have served as a basis for additional research on laboratory recruitment, retention, education, marketing, certification, and advocacy. The 2015 wage survey was conducted through collaboration between the ASCP's Institute of Science, Technology, and Policy in Washington, DC, and the ASCP Board of Certification in Chicago, Illinois. Electronic survey invitations were sent to individuals who are currently practicing in the field. Data reveal increased salaries since 2013 for all staff-level laboratory professionals surveyed except phlebotomists and pathologists' assistants. Laboratory assistants and phlebotomists, regardless of level, continue to have lower salaries while pathologists' assistants and administration personnel have higher salaries than the rest of the laboratory professions surveyed. Survey results put emphasis on strategic recruitment and retention by laboratory training programs and institutions that hire laboratory professionals. © American Society for Clinical Pathology, 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Skills training in laboratory and clerkship: connections, similarities, and differences

Directory of Open Access Journals (Sweden)

Berit Eika, MD, PhD

2003-03-01

Full Text Available Context: During the third semester of a 6 year long curriculum medical students train clinical skills in the skills laboratory (2 hours per week for 9 weeks as well as in an early, 8 week clinical clerkship at county hospitals. Objectives: to study students’ expectations and attitudes towards skills training in the skills laboratory and clerkship. Subjects: 126 medical students in their 3rd semester. Methods: During the fall of 2001 three consecutive, constructed questionnaires were distributed prior to laboratory training, following laboratory training but prior to clerkships, and following clerkships respectively. Results: Almost all (98% respondents found that training in skills laboratory improved the outcome of the early clerkship and 70% believed in transferability of skills from the laboratory setting to clerkship. Still, a majority (93% of students thought that the clerkship provided students with a better opportunity to learn clinical skills when compared to the skills laboratory. Skills training in laboratory as well as in clerkship motivated students for becoming doctors. Teachers in both settings were perceived as being committed to their teaching jobs, to demonstrate skills prior to practice, and to give students feed back with a small but significant more positive rating of the laboratory. Of the 22 skills that students had trained in the laboratory, a majority of students tried out skills associated with physical examination in the clerkship, whereas only a minority of students tried out more intimate skills. Female medical students tried significantly fewer skills during their clerkship compared to male students. Conclusions: Students believe that skills laboratory training prepare them for their subsequent early clerkship but favour the clerkship over the laboratory

Ecology studies at the Idaho National Engineering Laboratory Radioactive Waste Management Complex

International Nuclear Information System (INIS)

Arthur, W.J.; Markham, O.D.

1978-01-01

In September 1977 a radioecological research program was initiated at the Idaho National Engineering Laboratory (INEL) Radioactive Waste Management Complex in the southcentral Idaho. The primary goals of the research are to: (1) determine floral and faunal composition in the area; (2) sample various ecosystem components for radionuclides; (3) determine impacts of small mammal burrowing and vegetation growth on movement of radioactive materials; (4) compare ambient radiation exposures to radiation doses received by animals inhabiting the area; and (5) understand the interrelationships between the organisms and their role in radionuclide transport

The Idaho National Engineering Laboratory Site environmental report for calendar year 1988

International Nuclear Information System (INIS)

Hoff, D.L.; Mitchell, R.G.; Moore, R.

1989-06-01

This report describes the monitoring program, the collection of foodstuffs at the Idaho National Engineering Laboratory (INEL) boundary and distant offsite locations, and the collection of air and water samples at Site locations and offsite boundary and distant locations. The report also compares and evaluates the samples results, discussing implications, if any. Significant environmental activities at the INEL Site during 1988, nonradioactive and radioactive effluent monitoring at the Site, and the US Geological Survey (USGS) ground-water monitoring program are also summarized. 42 refs., 15 figs., 12 tabs

Description of the Sandia National Laboratories science, technology & engineering metrics process.

Energy Technology Data Exchange (ETDEWEB)

Jordan, Gretchen B.; Watkins, Randall D.; Trucano, Timothy Guy; Burns, Alan Richard; Oelschlaeger, Peter

2010-04-01

There has been a concerted effort since 2007 to establish a dashboard of metrics for the Science, Technology, and Engineering (ST&E) work at Sandia National Laboratories. These metrics are to provide a self assessment mechanism for the ST&E Strategic Management Unit (SMU) to complement external expert review and advice and various internal self assessment processes. The data and analysis will help ST&E Managers plan, implement, and track strategies and work in order to support the critical success factors of nurturing core science and enabling laboratory missions. The purpose of this SAND report is to provide a guide for those who want to understand the ST&E SMU metrics process. This report provides an overview of why the ST&E SMU wants a dashboard of metrics, some background on metrics for ST&E programs from existing literature and past Sandia metrics efforts, a summary of work completed to date, specifics on the portfolio of metrics that have been chosen and the implementation process that has been followed, and plans for the coming year to improve the ST&E SMU metrics process.

Low-level waste incineration at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Gillins, R.L.; Davis, J.N.; Maughan, R.Y.; Logan, J.A.

1985-01-01

A facility for the incineration of low-level beta/gamma contaminated combustible waste has been constructed at the Waste Experimental Reduction Facility (WERF) at the Idaho National Engineering Laboratory (INEL). The incineration facility was established to: (1) reduce the volume of currently generated contaminated combustible waste being disposed at the INEL's radioactive waste disposal site and thereby prolong the site's useful life; and (2) develop waste processing technology by providing a facility where full-size processes and equipment can be demonstrated and proven during production-scale operations. Cold systems testing has been completed, and contaminated operations began in September of 1984. Currently the facility is processing waste packaged in 2 x 2 x 2 ft cardboard boxes and measuring <10mR/h at contact. 3 figs

ADHD: Tips to Try

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español ADHD: Tips to Try KidsHealth / For Teens / ADHD: Tips to Try Print en español TDAH: Consejos que puedes probar ADHD , short for attention deficit hyperactivity disorder , is a ...

2003 Wastewater Land Application Site Performance Reports for the Idaho National Engineering and Environmental Laboratory

Energy Technology Data Exchange (ETDEWEB)

Teresa R. Meachum

2004-02-01

The 2003 Wastewater Land Application Site Performance Reports for the Idaho National Engineering and Environmental Laboratory describe the conditions for the facilities with State of Idaho Wastewater Land Application Permits. Permit-required monitoring data are summarized, and permit exceedences or environmental impacts relating to the operations of the facilities during the 2003 permit year are discussed.

Evaporation Basin Test Reactor Area, Idaho National Engineering Laboratory: Environmental assessment

International Nuclear Information System (INIS)

1991-12-01

The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA-0501, on the construction and operation of the proposed Evaporation Basin at the Test Reactor Area (TRA) at the Idaho National Engineering Laboratory (INEL) near Idaho Falls, Idaho. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment, within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, the preparation of an environmental impact statement (EIS) is not required, and the Department is issuing this Finding of No Significant Impact

Decree-Law No. 361/79 of 8 August 1979 determining the structure and competence of the National Laboratory of Industrial Engineering and Technology

International Nuclear Information System (INIS)

1979-01-01

This Decree-Law determines the structure and scope of the National Laboratory of Industrial Engineering and Technology (LNETI) which now includes the Nuclear Physics and Engineering Laboratory of the Junta de Energia Nuclear and its central services. The nuclear activities of the LNETI are divided into three sectors: the Department for Radiological Protection and Safety, responsible for radiation protection in nuclear installations and for the safety of nuclear equipment; the Department for Energy and Nuclear Engineering, responsible for R and D in nuclear engineering and for nuclear energy production; and finally, the Department for Nuclear Science and Technology, in charge of R and D in nuclear science and of promoting the application of nuclear technology for peaceful purposes. (NEA) [fr

Third phase formation in the extraction of Th(NO_3)_4 by Tri-sec-butyl phosphate. A comparison with Tri-n-butyl phosphate

International Nuclear Information System (INIS)

Chandrasekar, Aditi; Suresh, A.; Sivaraman, N.

2017-01-01

Earlier studies carried out in our laboratory indicated that Tri-sec-butyl phosphate (TsBP) is a potential extractant for U/Th separation. Also, the third phase formation tendency of TsBP is lower compared to its isomers, Tri-n-butyl-phosphate (TBP) and Tri-iso-butyl phosphate (TiBP). In this context, the extraction and third phase formation behaviour of 1.1 M solutions of TiBP and TsBP in n-dodecane in the extraction of Th(IV) from 1 M HNO_3 at 303 K over a wide range of Th concentrations were investigated in the present study and the results are compared with the literature data on TBP system. Concentrations of Th(IV) and HNO_3 loaded in the organic phase before third phase formation (biphasic region) as well as in third phase and diluent-rich phase after third phase formation (triphasic region) were measured as a function of equilibrium aqueous phase Th(IV) concentration. The density of loaded organic phase was also measured at various Th(IV) concentrations. The extraction profiles in the biphasic region indicated that extraction of Th(IV) by TBP is higher than that of TiBP which in turn is higher than that of TsBP. Extractant concentration in the diluent-rich phase and third phase was measured for the triphasic region.

Aerosol in selected laboratories at Faculty of Mechanical Engineering, Opole University of Technology

Science.gov (United States)

Olszowski, Tomasz

2017-10-01

The paper contains the results of a study into mass concentration of the dispersed aerosol fraction with the aerodynamic diameter of up to 2.5 and 10 micrometers. The study was conducted during classes with students participating in them in two laboratories located at Faculty of Mechanical Engineering, Opole University of Technology as well as outdoor outside the building. It was demonstrated that the values of the mass concentration of PM2.5 and PM10 measured in the laboratories differ considerably from the levels measured in the ambient air in the outdoor areas surrounding the faculty building. It was concluded that the diversity of PM2.5/PM10 ratio was greater in the laboratories. Direct correlation was not established between the concentrations of the particular PM fractions in the two investigated environments. It was demonstrated that there is a statistically significant relation between the concentration of PM2.5 and PM10 and the number of people present in the laboratory. The conducted cluster analysis led to the detection of the existence of dominant structures determining air quality parameters. For the analyzed case, endogenic factors are responsible for the aerosanitary condition. The study demonstrated that the evaluation of air quality needs to be performed individually for the specific rooms.

Review of occupational radiation exposures in all biennial shutdown maintenance of Kaiga generating station

International Nuclear Information System (INIS)

Murukan, E.K.; Vinod Kumar, T.; Austine, N.X.; Soumia Menon, M.; Girish Kumar, K.; Rao, M.M.L.N.; Venkataramana, K.

2008-01-01

Full text: Kaiga generating station 1 and 2 consists of twin units of 220 M We pressurized heavy water reactors located in Karnataka, India. Major maintenance activities of one of the twin units are taken up once in two years (biennial shutdown) to execute system maintenance, system up gradation, surveillance and in-service inspection (ISI) jobs. BSDs are mandatory activities to comply with regulatory requirement to ensure the safety and reliability of plant system equipment. More than 65% of the station collective dose is contributed by biennial shutdown (BSD) jobs. It is observed that the man rem consumed during normal operation of the plant is less than 35% of the total man rem consumed. Since BSD jobs contributes significantly to station collective dose, an effective implementation of radiation protection programme specific to BSD is the key to control the occupational exposure. Various improvements in the field of radiation protection practices and process systems are adopted to achieve lowest collective dose at par with international standards. The key areas identified for application of various strategies to achieve ALARA were Man rem budgeting, Radiological condition monitoring, Radiation protection practices, Identification of critical jobs and Work groups, Work planning and execution, and Radioactive waste management. Review of collective doses of all the BSD jobs performed in the station since year 2004 and various measures incorporated to achieve ALARA exposures to plant personnel are briefly discussed in this paper. (author)

Engineered nanomaterials: toward effective safety management in research laboratories.

Science.gov (United States)

Groso, Amela; Petri-Fink, Alke; Rothen-Rutishauser, Barbara; Hofmann, Heinrich; Meyer, Thierry

2016-03-15

It is still unknown which types of nanomaterials and associated doses represent an actual danger to humans and environment. Meanwhile, there is consensus on applying the precautionary principle to these novel materials until more information is available. To deal with the rapid evolution of research, including the fast turnover of collaborators, a user-friendly and easy-to-apply risk assessment tool offering adequate preventive and protective measures has to be provided. Based on new information concerning the hazards of engineered nanomaterials, we improved a previously developed risk assessment tool by following a simple scheme to gain in efficiency. In the first step, using a logical decision tree, one of the three hazard levels, from H1 to H3, is assigned to the nanomaterial. Using a combination of decision trees and matrices, the second step links the hazard with the emission and exposure potential to assign one of the three nanorisk levels (Nano 3 highest risk; Nano 1 lowest risk) to the activity. These operations are repeated at each process step, leading to the laboratory classification. The third step provides detailed preventive and protective measures for the determined level of nanorisk. We developed an adapted simple and intuitive method for nanomaterial risk management in research laboratories. It allows classifying the nanoactivities into three levels, additionally proposing concrete preventive and protective measures and associated actions. This method is a valuable tool for all the participants in nanomaterial safety. The users experience an essential learning opportunity and increase their safety awareness. Laboratory managers have a reliable tool to obtain an overview of the operations involving nanomaterials in their laboratories; this is essential, as they are responsible for the employee safety, but are sometimes unaware of the works performed. Bringing this risk to a three-band scale (like other types of risks such as biological, radiation

Information engineering

Energy Technology Data Exchange (ETDEWEB)

Hunt, D.N.

1997-02-01

The Information Engineering thrust area develops information technology to support the programmatic needs of Lawrence Livermore National Laboratory`s Engineering Directorate. Progress in five programmatic areas are described in separate reports contained herein. These are entitled Three-dimensional Object Creation, Manipulation, and Transport, Zephyr:A Secure Internet-Based Process to Streamline Engineering Procurements, Subcarrier Multiplexing: Optical Network Demonstrations, Parallel Optical Interconnect Technology Demonstration, and Intelligent Automation Architecture.

Bibliography of Connecticut Advanced Nuclear Engineering Laboratory reports

Energy Technology Data Exchange (ETDEWEB)

NONE

1965-12-01

This report, published in two volumes, is a bibliography of the reports published at the Connecticut Advanced Nuclear Engineering Laboratory (CANEL). The reports cover the period 1952 through 1965 and include the Aircraft Nuclear Propulsion program, the Advanced Liquid Metal Cooled Reactor program, the Advanced Reactor Materials program and the SNAP-50 program. The bibliography contains the report number, title, author, date published, and classification. In some cases where the writing of a report was a group effort, and in some reports containing compilations of certain types of data, the author column is not applicable. This is indicated by a {open_quotes}n.a.{close_quotes} in the author column. The following types of reports are included: PWAC`s, TIM`s, CNLM`s, FXM`s and miscellaneous reports. PWAC and TIM reports conform to the requirements of AEC Manual Chapter 3202-041 and 3202-042, respectively. Most of the technical information of interest generated by this project is documented in these reports. CNLM and FXM reports were written primarily for internal distribution. However, these reports contain enough information of technical interest to warrant their inclusion. All CNLM`s and those FXM`s considered to be of interest are included in this bibliography. The MPR`s (Monthly Progress Reports) are the most important of the miscellaneous categories of reports. The other miscellaneous categories relate primarily to equipment and reactor specifications. The Division of Technical Information Extension (DTIE) at Oak Ridge, Tennessee has been designated as the primary recipient of the reports in the CANEL library. When more than one copy of a report was available, the additional copies were delivered to the Lawrence Radiation Laboratory, Livermore, California.

Bibliography of Connecticut Advanced Nuclear Engineering Laboratory reports

Energy Technology Data Exchange (ETDEWEB)

NONE

1965-12-01

This report, published in two, volumes, is a bibliography of the reports published at the Connecticut Advanced Nuclear Engineering Laboratory (CANEL). The reports cover the period 1952 through 1965 and include the Aircraft Nuclear Propulsion program, the Advanced Liquid Metal Cooled Reactor program, the Advanced Reactor Materials program and the SNAP-50 program. The bibliography contains the report number, title, author, date published, and classification. In some cases where the writing of a report was a group effort, and in some reports containing compilations of certain types of data, the author column is not applicable. This is indicated by a {open_quotes}n.a.{close_quotes} in the author column. The following types of reports are included: PWAC`s, TIM`s, CNLM`s. FXM`s and miscellaneous reports. PWAC and TIM reports conform to the requirements of AEC Manual Chapter 3202-041 and 3202-042, respectively. Most of the technical information of interest generated by this project is documented in these reports, CNLM and FXM reports were written primarily for internal distribution. However, these reports contain enough information of technical interest to warrant their inclusion. All CNLM`s and those FXM`s considered to be of interest are included in this bibliography. The MPR`s (Monthly Progress Reports) are the most important of the miscellaneous categories of reports. The other miscellaneous categories relate primarily to equipment and reactor specifications. The Division of Technical Information Extension (DTIE) at Oak Ridge, Tennessee has been designated as the primary recipient of the reports in the CANEL library. When more than one copy of a report was available, the additional copies were delivered to the Lawrence Radiation Laboratory, Livermore, California.

Vertical and Horizontal Integration of Laboratory Curricula and Course Projects across the Electronic Engineering Technology Program

Science.gov (United States)

Zhan, Wei; Goulart, Ana; Morgan, Joseph A.; Porter, Jay R.

2011-01-01

This paper discusses the details of the curricular development effort with a focus on the vertical and horizontal integration of laboratory curricula and course projects within the Electronic Engineering Technology (EET) program at Texas A&M University. Both software and hardware aspects are addressed. A common set of software tools are…

Experimental Research of Engine Foundations

Directory of Open Access Journals (Sweden)

Violeta-Elena Chiţan

2004-01-01

Full Text Available This paper tries a compact presentation of experimental research of engine-foundations. The dynamic phenomena are so complex, that the vibrations cannot be estimated in the design stage. The design engineer of an engine foundation must foresee through a dynamic analysis of the vibrations, those measures that lead to the avoidance or limiting of the bad effects caused by the vibrations.

Central Laboratories Services

Data.gov (United States)

Federal Laboratory Consortium — The TVA Central Laboratories Services is a comprehensive technical support center, offering you a complete range of scientific, engineering, and technical services....

Program and book of abstracts of the 23rd biennial conference of the Ghana Science Association

International Nuclear Information System (INIS)

2003-08-01

The twenty-third biennial conference of the Ghana Science Association was held on 4-7 August, 2003 in Kumasi. The theme of the conference was-The HIV/AIDS pandemic: challenges for the Ghanaian scientists. This publication contains the program, and about 200 abstracts of papers presented at the conference including poster sessions. The abstracts have been arranged under the following broad subject areas: Biomedical, Agriculture, Food and Nutrition, Physical and General (E.A.A.)

Award-winning articles and posters from the World Federation of Chiropractic's 12th Biennial Congress 2013.

Science.gov (United States)

Haldeman, Scott; Chapman-Smith, David

2014-01-01

This editorial reviews the original research submissions to the World Federation of Chiropractic's 12th Biennial Congress held in Durban, South Africa from April 10 - 13, 2013, and the four award-winning scientific articles in the NCMIC Louis Sportelli Research Awards competition at the Congress which are published in this issue of the Journal of Manipulative and Physiological Therapeutics. Copyright © 2014 National University of Health Sciences. Published by Mosby, Inc. All rights reserved.

Application of engineered sorbent barriers Summary of Laboratory Data for FY 1988

Energy Technology Data Exchange (ETDEWEB)

Freeman, H.D.; Jones, E.O.

1989-09-01

Laboratory studies were conducted in FY 1988 Pacific Northwest Laboratory to determine the effect of contact time, pH, solution to solid ratio, and particle size on the performance of a number of materials in adsorbing radioactive cobalt, strontium, and cesium. The laboratory studies were conducted to provide background information useful in designing an engineered sorbent barrier, which restricts the migration of radionuclides from low-level waste sites. Understanding how the variables affect the adsorption of ions on the sorbent materials is the key to estimating the performance of sorbent barriers under a variety of conditions. The scope of the studies was limited to three radionuclides and four sorbent materials, but the general approach can be used to evaluate other radionuclides and conditions. The sorbent materials evaluated in this study included clinoptilolite, activated carbon, bentonite clay, and Savannah River soil. The clinoptilolite and activated carbon were identified in previous studies as the most cost-effective materials for sorption of the three radionuclides under consideration. The bentonite clay was evaluated as a component of the barrier that could be used to modify the permeability of the barrier system. The Savannah River soil was used to represent soil from a humid site. 3 refs., 14 figs., 1 tab.

Implementation and use of cloud-based electronic lab notebook in a bioprocess engineering teaching laboratory.

Science.gov (United States)

Riley, Erin M; Hattaway, Holly Z; Felse, P Arthur

2017-01-01

Electronic lab notebooks (ELNs) are better equipped than paper lab notebooks (PLNs) to handle present-day life science and engineering experiments that generate large data sets and require high levels of data integrity. But limited training and a lack of workforce with ELN knowledge have restricted the use of ELN in academic and industry research laboratories which still rely on cumbersome PLNs for recordkeeping. We used LabArchives, a cloud-based ELN in our bioprocess engineering lab course to train students in electronic record keeping, good documentation practices (GDPs), and data integrity. Implementation of ELN in the bioprocess engineering lab course, an analysis of user experiences, and our development actions to improve ELN training are presented here. ELN improved pedagogy and learning outcomes of the lab course through stream lined workflow, quick data recording and archiving, and enhanced data sharing and collaboration. It also enabled superior data integrity, simplified information exchange, and allowed real-time and remote monitoring of experiments. Several attributes related to positive user experiences of ELN improved between the two subsequent years in which ELN was offered. Student responses also indicate that ELN is better than PLN for compliance. We demonstrated that ELN can be successfully implemented in a lab course with significant benefits to pedagogy, GDP training, and data integrity. The methods and processes presented here for ELN implementation can be adapted to many types of laboratory experiments.

Virtual-reality-based educational laboratories in fiber optic engineering

Science.gov (United States)

Hayes, Dana; Turczynski, Craig; Rice, Jonny; Kozhevnikov, Michael

2014-07-01

Researchers and educators have observed great potential in virtual reality (VR) technology as an educational tool due to its ability to engage and spark interest in students, thus providing them with a deeper form of knowledge about a subject. The focus of this project is to develop an interactive VR educational module, Laser Diode Characteristics and Coupling to Fibers, to integrate into a fiber optics laboratory course. The developed module features a virtual laboratory populated with realistic models of optical devices in which students can set up and perform an optical experiment dealing with laser diode characteristics and fiber coupling. The module contains three increasingly complex levels for students to navigate through, with a short built-in quiz after each level to measure the student's understanding of the subject. Seventeen undergraduate students learned fiber coupling concepts using the designed computer simulation in a non-immersive desktop virtual environment (VE) condition. The analysis of students' responses on the updated pre- and post tests show statistically significant improvement of the scores for the post-test as compared to the pre-test. In addition, the students' survey responses suggest that they found the module very useful and engaging. The conducted study clearly demonstrated the feasibility of the proposed instructional technology for engineering education, where both the model of instruction and the enabling technology are equally important, in providing a better learning environment to improve students' conceptual understanding as compared to other instructional approaches.

Rapid Prototyping Laboratory

Data.gov (United States)

Federal Laboratory Consortium — The ARDEC Rapid Prototyping (RP) Laboratory was established in December 1992 to provide low cost RP capabilities to the ARDEC engineering community. The Stratasys,...

Neural Systems Laboratory

Data.gov (United States)

Federal Laboratory Consortium — As part of the Electrical and Computer Engineering Department and The Institute for System Research, the Neural Systems Laboratory studies the functionality of the...

Idaho National Engineering Laboratory site environmental report for calendar year 1995

International Nuclear Information System (INIS)

Mitchell, R.G.; Peterson, D.; Hoff, D.L.

1996-08-01

This report presents a compilation of data collected in 1995 for the routine environmental surveillance programs conducted on and around the Idaho National Engineering Laboratory (INEL). During 1995, the offsite surveillance program was conducted by the Environmental Science and Research Foundation. Onsite surveillance was performed by Lockheed Idaho Technologies Company (LITCO). Ground-water monitoring, both on and offsite, was performed by the US Geological Survey (USGS). This report also presents summaries of facility effluent monitoring data collected by INEL contractors. This report, prepared in accordance with the requirements in DOE Order 5400.1, is not intended to cover the numerous special environmental research programs being conducted at the INEL by the Foundation, LITCO, USGS, and others

Low-level waste incineration: experience at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Bohrer, H.A.; Dalton, J.D.

1987-01-01

The Waste Experimental Reduction Facility (WERF) is a low level radioactive waste treatment facility being operated at the Idaho National Engineering Laboratory (INEL). A key component of the facility is a dual chambered controlled air incinerator with a dry off-gas treatment system. The incinerator began processing radioactive waste in September, 1984. Limited operations continued from that data until October, 1985, at which time all INEL generators began shipping combustible waste for incineration. The incinerator is presently processing all available INEL combustible Dry Active Waste (DAW) (approximately 1700 m 3 per year) operating about five days per month. Performance to date has demonstrated the effectiveness, viability and safety of incineration as a volume reduction method of DAW. 3 figures

Idaho National Engineering Laboratory site environmental report for calendar year 1995

Energy Technology Data Exchange (ETDEWEB)

Mitchell, R.G.; Peterson, D.; Hoff, D.L.

1996-08-01

This report presents a compilation of data collected in 1995 for the routine environmental surveillance programs conducted on and around the Idaho National Engineering Laboratory (INEL). During 1995, the offsite surveillance program was conducted by the Environmental Science and Research Foundation. Onsite surveillance was performed by Lockheed Idaho Technologies Company (LITCO). Ground-water monitoring, both on and offsite, was performed by the US Geological Survey (USGS). This report also presents summaries of facility effluent monitoring data collected by INEL contractors. This report, prepared in accordance with the requirements in DOE Order 5400.1, is not intended to cover the numerous special environmental research programs being conducted at the INEL by the Foundation, LITCO, USGS, and others.

Solidification of hazardous and mixed radioactive waste at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Boehmer, A.M.; Larsen, M.M.

1986-01-01

EG and G Idaho has initiated a program to develop treatment options for the hazardous and mixed wastes generated at the Idaho National Engineering Laboratory (INEL). This program includes development of solidification methods for some of these wastes. Testing has shown that toxic wastes can be successfully solidified using cement, cement-silicate, or ENVIROSTONE binders to produce nontoxic stable waste forms for safe, long term disposal. This paper presents the results of the solidification development program conducted at the INEL by EG and G Idaho

Solidification of hazardous and mixed radioactive waste at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Boehmer, A.M.; Larsen, M.M.

1986-03-01

EG and G Idaho has initiated a program to develop treatment options for the hazardous and mixed wastes generated at the Idaho National Engineering Laboratory (INEL). This program includes development of solidification methods for some of these wastes. Testing has shown that toxic wastes can be successfully solidified using cement, cement-silicate, or ENVIROSTONE binders to produce nontoxic stable waste forms for safe, long term disposal. This paper presents the results of the solidification development program conducted at the INEL by EG and G Idaho

Nearly identical cycles of the quasi-biennial oscillation in the equatorial lower stratosphere

Science.gov (United States)

Dunkerton, T. J.

2017-08-01

As a nonlinear dynamical system with limit cycles but subject to periodic forcings associated with the seasonal cycle, the quasi-biennial oscillation (QBO) displays seasonal modulation such that phase transitions are more likely to occur in certain months than in others. Modulation is distinct from seasonal synchronization, defined as quantized QBO periods and identical cycles. Instead, nearly identical QBO cycles can be identified in the data having similar period, internal structure, and (optionally) timing with respect to the calendar year. Four such categories are found using a spectral phase method based on the 2-D phase space of the leading rotated principal components (RPCs) of near-equatorial monthly mean zonal wind in the layer 70-10 hPa. The most prominent category, containing as many as 15 cycles of the 28 observed thus far, is "nearly biennial" with period slightly greater than 24 months. All results, prior to the recent QBO anomaly in Cycle 28, are demonstrated to be statistically stationary in the sense that the RPCs are temporally invariant and insensitive to the inclusion of data to 100 hPa and with higher vertical resolution. Inclusion of Cycle 28 has no effect on the rotated empirical orthogonal functions but a microscopic change in the long-term average, since strong easterlies are missing in the anomalous cycle. For objective definition of QBO cycles in physical space-time, westerly onsets in the 40-53 hPa layer are least likely to stall and provide unambiguous starting times. Half of these onsets cluster in April-May, consistent with the seasonal modulation obtained with the spectral phase method.

Case Studies in Sustainability Used in an Introductory Laboratory Course to Enhance Laboratory Instruction

Science.gov (United States)

Luster-Teasley, Stephanie; Hargrove-Leak, Sirena; Gibson, Willietta; Leak, Roland

2017-01-01

This educational research seeks to develop novel laboratory modules by using Case Studies in the Science Teaching method to introduce sustainability and environmental engineering laboratory concepts to 21st century learners. The increased interest in "going green" has led to a surge in the number of engineering students studying…

Adsorption of Oxy-Anions in the Teaching Laboratory: An Experiment to Study a Fundamental Environmental Engineering Problem

Science.gov (United States)

D'Arcy, Mitch; Bullough, Florence; Moffat, Chris; Borgomeo, Edoardo; Teh, Micheal; Vilar, Ramon; Weiss, Dominik J.

2014-01-01

Synthesizing and testing bicomposite adsorbents for the removal of environmentally problematic oxy-anions is high on the agenda of research-led universities. Here we present a laboratory module successfully developed at Imperial College London that introduces the advanced undergraduate student in engineering (chemical, civil, earth) and science…

Site-specific probabilistic seismic hazard analyses for the Idaho National Engineering Laboratory. Volume 1: Final report

International Nuclear Information System (INIS)

1996-05-01

This report describes and summarizes a probabilistic evaluation of ground motions for the Idaho National Engineering Laboratory (INEL). The purpose of this evaluation is to provide a basis for updating the seismic design criteria for the INEL. In this study, site-specific seismic hazard curves were developed for seven facility sites as prescribed by DOE Standards 1022-93 and 1023-96. These sites include the: Advanced Test Reactor (ATR); Argonne National Laboratory West (ANL); Idaho Chemical Processing Plant (ICPP or CPP); Power Burst Facility (PBF); Radioactive Waste Management Complex (RWMC); Naval Reactor Facility (NRF); and Test Area North (TAN). The results, probabilistic peak ground accelerations and uniform hazard spectra, contained in this report are not to be used for purposes of seismic design at INEL. A subsequent study will be performed to translate the results of this probabilistic seismic hazard analysis to site-specific seismic design values for the INEL as per the requirements of DOE Standard 1020-94. These site-specific seismic design values will be incorporated into the INEL Architectural and Engineering Standards

11th Biennial Conference on Emerging Mathematical Methods, Models and Algorithms for Science and Technology

CERN Document Server

Manchanda, Pammy; Bhardwaj, Rashmi

2015-01-01

The present volume contains invited talks of 11th biennial conference on “Emerging Mathematical Methods, Models and Algorithms for Science and Technology”. The main message of the book is that mathematics has a great potential to analyse and understand the challenging problems of nanotechnology, biotechnology, medical science, oil industry and financial technology. The book highlights all the features and main theme discussed in the conference. All contributing authors are eminent academicians, scientists, researchers and scholars in their respective fields, hailing from around the world.

How the Affordable Care Act Has Helped Women Gain Insurance and Improved Their Ability to Get Health Care: Findings from the Commonwealth Fund Biennial Health Insurance Survey, 2016.

Science.gov (United States)

Gunja, Munira Z; Collins, Sara R; Doty, Michelle M; Beautel, Sophie

2017-08-01

ISSUE: Prior to the Affordable Care Act (ACA), one-third of women who tried to buy a health plan on their own were either turned down, charged a higher premium because of their health, or had specific health problems excluded from their plans. Beginning in 2010, ACA consumer protections, particularly coverage for preventive care screenings with no cost-sharing and a ban on plan benefit limits, improved the quality of health insurance for women. In 2014, the law’s major insurance reforms helped millions of women who did not have employer insurance to gain coverage through the ACA’s marketplaces or through Medicaid. GOALS: To examine the effects of ACA health reforms on women’s coverage and access to care. METHOD: Analysis of the Commonwealth Fund Biennial Health Insurance Surveys, 2001–2016. FINDINGS AND CONCLUSIONS: Women ages 19 to 64 who shopped for new coverage on their own found it significantly easier to find affordable plans in 2016 compared to 2010. The percentage of women who reported delaying or skipping needed care because of costs fell to an all-time low. Insured women were more likely than uninsured women to receive preventive screenings, including Pap tests and mammograms.

Waste Isolation Pilot Plant Biennial Environmental Compliance Report

International Nuclear Information System (INIS)

2006-01-01

This Biennial Environmental Compliance Report (BECR) documents compliance with environmental regulations at the Waste Isolation Pilot Plant (WIPP), a facility designed and authorized for the safe disposal of transuranic (TRU) radioactive waste. This BECR covers the reporting period from April 1, 2004, to March 31, 2006. As required by the WIPP Land Withdrawal Act (LWA) (Public Law [Pub. L.] 102-579, as amended by Pub. L. 104-201), the BECR documents United States (U.S.) Department of Energy (DOE) compliance with regulations and permits issued pursuant to the following: (1) Title 40 Code of Federal Regulations (CFR) Part 191, Subpart A, 'Environmental Standards for Management and Storage'; (2) Clean Air Act (CAA) (42 United States Code [U.S.C.] 7401, et seq.); (3) Solid Waste Disposal Act (SWDA) (42 U.S.C. 6901-6992, et seq.); (4) Safe Drinking Water Act (SDWA) (42 U.S.C. 300f, et seq.); (5) Toxic Substances Control Act (TSCA) (15 U.S.C. 2601, et seq.); (6) Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) (42 U.S.C. 9601, et seq.); and all other federal and state of New Mexico laws pertaining to public health and safety or the environment.

Reducing the number of laboratory animals used in tissue engineering research by restricting the variety of animal models. Articular cartilage tissue engineering as a case study

NARCIS (Netherlands)

Vries, R.B.M. de; Buma, P.; Leenaars, M.; Ritskes-Hoitinga, M.; Gordijn, B.

2012-01-01

The use of laboratory animals in tissue engineering research is an important underexposed ethical issue. Several ethical questions may be raised about this use of animals. This article focuses on the possibilities of reducing the number of animals used. Given that there is considerable debate about

Hazardous and mixed waste solidification development conducted at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Boehmer, A.M.; Larsen, M.M.

1986-04-01

EG and G Idaho, Inc., has initiated a program to develop safe, efficient, cost-effective solidification treatment methods for the disposal of some of the hazardous and mixed wastes generated at the Idaho National Engineering Laboratory (INEL). Testing has shown that Extraction Procedure (EP) toxic wastes can be successfully solidified using cement, cement-silicate, or ENVIROSTONE binders to produce nontoxic stable waste forms for safe, long-term disposal as general or low-level waste, depending upon the radioactivity. The results of the solidification development program are presented in this report

Low-dose computed tomography for lung cancer screening: comparison of performance between annual and biennial screen

Energy Technology Data Exchange (ETDEWEB)

Sverzellati, Nicola; Silva, M. [University of Parma, Radiology, Department of Surgical Sciences, Parma (Italy); Calareso, G.; Marchiano, A. [Fondazione IRCCS Istituto Nazionale dei Tumori, Department of Radiology, Milan (Italy); Galeone, C. [University of Milano-Bicocca, Department of Statistics and Quantitative Methods, Division of Biostatistics, Epidemiology and Public Health, Laboratory of Healthcare Research and Pharmacoepidemiology, Milan (Italy); Sestini, S.; Pastorino, U. [Fondazione IRCCS Istituto Nazionale dei Tumori, Department of Surgery, Section of Thoracic Surgery, Milan (Italy); Sozzi, G. [Fondazione IRCCS Istituto Nazionale dei Tumori, Tumor Genomics Unit, Department of Experimental Oncology and Molecular Medicine, Milan (Italy)

2016-11-15

To compare the performance metrics of two different strategies of lung cancer screening by low-dose computed tomography (LDCT), namely, annual (LDCT1) or biennial (LDCT2) screen. Recall rate, detection rate, interval cancers, sensitivity, specificity, positive and negative predictive values (PPV and NPV, respectively) were compared between LDCT1 and LDCT2 arms of the MILD trial over the first seven (T0-T6; median follow-up 7.3 years) and four rounds (T0-T3; median follow-up 7.3 years), respectively. 1152 LDCT1 and 1151 LDCT2 participants underwent a total of 6893 and 4715 LDCT scans, respectively. The overall recall rate was higher in LDCT2 arm (6.97 %) than in LDCT1 arm (5.81 %) (p = 0.01), which was counterbalanced by the overall lower number of LDCT scans. No difference was observed for the overall detection rate (0.56 % in both arms). The two LDCT arms had similar specificity (99.2 % in both arms), sensitivity (73.5 %, in LDCT2 vs. 68.5 % in LDCT1, p = 0.62), PPV (42.4 %, in LDCT2, vs. 40.6 %, in LDCT1, p = 0.83) and NPV (99.8 %, in LDCT2 vs. 99.7 %, in LDCT1, p = 0.71). Biennial screen may save about one third of LDCT scans with similar performance indicators as compared to annual screening. (orig.)

Low-dose computed tomography for lung cancer screening: comparison of performance between annual and biennial screen

International Nuclear Information System (INIS)

Sverzellati, Nicola; Silva, M.; Calareso, G.; Marchiano, A.; Galeone, C.; Sestini, S.; Pastorino, U.; Sozzi, G.

2016-01-01

To compare the performance metrics of two different strategies of lung cancer screening by low-dose computed tomography (LDCT), namely, annual (LDCT1) or biennial (LDCT2) screen. Recall rate, detection rate, interval cancers, sensitivity, specificity, positive and negative predictive values (PPV and NPV, respectively) were compared between LDCT1 and LDCT2 arms of the MILD trial over the first seven (T0-T6; median follow-up 7.3 years) and four rounds (T0-T3; median follow-up 7.3 years), respectively. 1152 LDCT1 and 1151 LDCT2 participants underwent a total of 6893 and 4715 LDCT scans, respectively. The overall recall rate was higher in LDCT2 arm (6.97 %) than in LDCT1 arm (5.81 %) (p = 0.01), which was counterbalanced by the overall lower number of LDCT scans. No difference was observed for the overall detection rate (0.56 % in both arms). The two LDCT arms had similar specificity (99.2 % in both arms), sensitivity (73.5 %, in LDCT2 vs. 68.5 % in LDCT1, p = 0.62), PPV (42.4 %, in LDCT2, vs. 40.6 %, in LDCT1, p = 0.83) and NPV (99.8 %, in LDCT2 vs. 99.7 %, in LDCT1, p = 0.71). Biennial screen may save about one third of LDCT scans with similar performance indicators as compared to annual screening. (orig.)

Third phase formation in the extraction of Th(NO{sub 3}){sub 4} by Tri-sec-butyl phosphate. A comparison with Tri-n-butyl phosphate

Energy Technology Data Exchange (ETDEWEB)

Chandrasekar, Aditi; Suresh, A.; Sivaraman, N. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Chemistry Group

2017-06-01

Earlier studies carried out in our laboratory indicated that Tri-sec-butyl phosphate (TsBP) is a potential extractant for U/Th separation. Also, the third phase formation tendency of TsBP is lower compared to its isomers, Tri-n-butyl-phosphate (TBP) and Tri-iso-butyl phosphate (TiBP). In this context, the extraction and third phase formation behaviour of 1.1 M solutions of TiBP and TsBP in n-dodecane in the extraction of Th(IV) from 1 M HNO{sub 3} at 303 K over a wide range of Th concentrations were investigated in the present study and the results are compared with the literature data on TBP system. Concentrations of Th(IV) and HNO{sub 3} loaded in the organic phase before third phase formation (biphasic region) as well as in third phase and diluent-rich phase after third phase formation (triphasic region) were measured as a function of equilibrium aqueous phase Th(IV) concentration. The density of loaded organic phase was also measured at various Th(IV) concentrations. The extraction profiles in the biphasic region indicated that extraction of Th(IV) by TBP is higher than that of TiBP which in turn is higher than that of TsBP. Extractant concentration in the diluent-rich phase and third phase was measured for the triphasic region.

Geophysical surveys for buried waste detection at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Sandness, G.A.; Rising, J.L.; Kimbrough, J.R.

1979-12-01

This report describes a series of geophysical surveys performed at the Idaho National Engineering Laboratory (INEL). The main purpose of the surveys was to evaluate techniques, principally ground-penetrating radar, for detecting and mapping radioactive wastes buried in shallow trenches and pits. A second purpose was to determine the feasibility of using ground-penetrating radar to measure the depth of basalt bedrock. A prototype geophyscal survey system developed by the US Department of Energy's Pacific Northwest Laboratory was used for this study. Radar, magnetometer, and metal detector measurements were made at three sites in the Radioactive Waste Management Complex (RWMC) at INEL. Radar measurements were made at fourth site adjacent to the RWMC. The combination of three geophysical methods was shown to provide considerable information about the distribution of buried waste materials. The tests confirmed the potential effectiveness of the radar method, but they also pointed out the need for continued research and development in ground-penetrating radar technology. The radar system tested in this study appears to be capable of measuring the depth to basalt in the vicinity of the RWMC

The Idaho National Engineering Laboratory Site Environmental Report for Calendar Year 1993

International Nuclear Information System (INIS)

Mitchell, R.G.

1994-07-01

Results of the various environmental monitoring programs for 1993 are presented from the Idaho National Engineering Laboratory (INEL) operations. Although some radioactive materials were discharged during Site operations, concentrations and doses to the surrounding population were of no health consequence and were far less than State of Idaho and Federal health protection guidelines. Chapter 2 summarizes INEL activities related to compliance with environmental regulations and laws for Calendar Year 1993. The major portion of the report summarizes results of the environmental surveillance program conducted by the DOE Radiological and Environmental Sciences Laboratory, which includes the collection of foodstuffs at the INEL boundary and distant offsite locations, and the collection of air and water samples at onsite locations and offsite boundary and distant locations. The report also compares and evaluates the sample results to appropriate federal regulations and standards and discusses implications, if any. The US Geological Survey (USGS) ground-water monitoring program is briefly summarized and data are included in maps showing the spread of contaminants. Effluent monitoring and nonradiological drinking water monitoring are discussed briefly and data are summarized

Environmental Management Plan for the Chemical Engineering Laboratory (LIQ of the National University of Colombia, Bogotá

Directory of Open Access Journals (Sweden)

Javier Gama Chávez

2004-01-01

Full Text Available An Enviromental Management Plan was formulated with the objective of improving the environmental performance of the Chemical Engineering Laboratory (LIQ. The plan was supported on the principles established by the ISO 140001 standard. In a first step, an environmental politic was proposed. Next, by means of an initial review of the laboratory, the most significant impacts related to the activities developed in the Laboratory were identified: dangerous chemical wastes accumulation, water contamination by effusions generation and air contamination. These impacts were the base for formulating following and control programs, furthermire, a training an communication program was done. All the programs, including the requiered documents and procedures, were published in the Environmental Management Plan and the Environmental Procedures Manual.

Education and Research Laboratories as a Means of Enhancing the Quality of Professional Engineering Education in Design and Production of Composite Parts

Science.gov (United States)

Khaliulin, Valentin I.; Gershtein, Elena M.

2016-01-01

Relevance of this research is determined by quality improvement of professional engineering education. The purpose of this paper is to offer practical recommendations for those interested in establishment of education and research laboratories as a means of enhancing the quality of professional engineering education in design and production of…

Polymer-Ceramic Composite Scaffolds: The Effect of Hydroxyapatite and β-tri-Calcium Phosphate

OpenAIRE

Boyang Huang; Guilherme Caetano; Cian Vyas; Jonny James Blaker; Carl Diver; Paulo Bártolo

2018-01-01

The design of bioactive scaffolds with improved mechanical and biological properties is an important topic of research. This paper investigates the use of polymer-ceramic composite scaffolds for bone tissue engineering. Different ceramic materials (hydroxyapatite (HA) and β-tri-calcium phosphate (TCP)) were mixed with poly-ε-caprolactone (PCL). Scaffolds with different material compositions were produced using an extrusion-based additive manufacturing system. The produced scaffolds were physi...

1995 annual epidemiologic surveillance report for Idaho National Engineering and Environmental Laboratory

International Nuclear Information System (INIS)

1995-01-01

The US Department of Energy's (DOE) conduct of epidemiologic surveillance provides an early warning system for health problems among workers. This program monitors illnesses and health conditions that result in an absence of five or more consecutive workdays, occupational injuries and illnesses, and disabilities and deaths among current workers. This report summarizes epidemiologic surveillance data collected from the Idaho National Engineering and Environmental Laboratory (INEEL) from January 1, 1995 through December 31, 1995. The data were collected by a coordinator at INEEL and submitted to the Epidemiologic Surveillance Data Center, located at Oak Ridge Institute for Science and Education, where quality control procedures and data analyses were carried out

Long-term land use future scenarios for the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

1995-08-01

In order to facilitate decision regarding environmental restoration activities at the Idaho National Engineering Laboratory (INEL), the United States Department of Energy, Idaho Operations Office (DOE-ID) conducted analyses to project reasonable future land use scenarios at the INEL for the next 100 years. The methodology for generating these scenarios included: review of existing DOE plans, policy statements, and mission statements pertaining to the INEL; review of surrounding land use characteristics and county developments policies; solicitation of input from local, county, state and federal planners, policy specialists, environmental professionals, and elected officials; and review of environmental and development constraints at the INEL site that could influence future land use

1995 annual epidemiologic surveillance report for Idaho National Engineering and Environmental Laboratory

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-31

The US Department of Energy's (DOE) conduct of epidemiologic surveillance provides an early warning system for health problems among workers. This program monitors illnesses and health conditions that result in an absence of five or more consecutive workdays, occupational injuries and illnesses, and disabilities and deaths among current workers. This report summarizes epidemiologic surveillance data collected from the Idaho National Engineering and Environmental Laboratory (INEEL) from January 1, 1995 through December 31, 1995. The data were collected by a coordinator at INEEL and submitted to the Epidemiologic Surveillance Data Center, located at Oak Ridge Institute for Science and Education, where quality control procedures and data analyses were carried out.

Vapor vacuum extraction treatability study at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Herd, M.D.; Matthern, G.; Michael, D.L.; Spang, N.; Downs, W.; Weidner, J.; Cleary, P.

1993-01-01

During the 1960s and early 1970s, barreled mixed waste containing volatile organic compounds (VOCS) and radioactive waste was buried at the Subsurface Disposal Area (SDA) at the Idaho National Engineering Laboratory (INEL) Radioactive Waste Management Complex (RWMC). Over time, some of the barrels have deteriorated allowing, VOC vapors to be released into the vadose zone. The primary VOC contaminates of concern are CCl 4 and trichloroethylene; however, chloroform, tetrachloroethylene, and 1,1,1-trichloroethane have also been detected. Vapor Vacuum Extraction (VVE) is one alternative being considered for remediation of the RWMC SDA vadose zone. A proposed pilot-scale treatability study (TS) will provide operation and maintenance costs for the design of the potential scale-up of the system

The status of soil mapping for the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Olson, G.L.; Lee, R.D.; Jeppesen, D.J.

1995-01-01

This report discusses the production of a revised version of the general soil map of the 2304-km 2 (890-mi 2 ) Idaho National Engineering Laboratory (INEL) site in southeastern Idaho and the production of a geographic information system (GIS) soil map and supporting database. The revised general soil map replaces an INEL soil map produced in 1978 and incorporates the most current information on INEL soils. The general soil map delineates large soil associations based on National Resources Conservation Services [formerly the Soil Conservation Service (SCS)] principles of soil mapping. The GIS map incorporates detailed information that could not be presented on the general soil map and is linked to a database that contains the soil map unit descriptions, surficial geology codes, and other pertinent information

An iterative method for tri-level quadratic fractional programming problems using fuzzy goal programming approach

Science.gov (United States)

Kassa, Semu Mitiku; Tsegay, Teklay Hailay

2017-08-01

Tri-level optimization problems are optimization problems with three nested hierarchical structures, where in most cases conflicting objectives are set at each level of hierarchy. Such problems are common in management, engineering designs and in decision making situations in general, and are known to be strongly NP-hard. Existing solution methods lack universality in solving these types of problems. In this paper, we investigate a tri-level programming problem with quadratic fractional objective functions at each of the three levels. A solution algorithm has been proposed by applying fuzzy goal programming approach and by reformulating the fractional constraints to equivalent but non-fractional non-linear constraints. Based on the transformed formulation, an iterative procedure is developed that can yield a satisfactory solution to the tri-level problem. The numerical results on various illustrative examples demonstrated that the proposed algorithm is very much promising and it can also be used to solve larger-sized as well as n-level problems of similar structure.

Air Emission Inventory for the Idaho National Engineering and Environmental Laboratory - Calendar Year 1999 Emission Report

Energy Technology Data Exchange (ETDEWEB)

Zohner, S.K.

2000-05-30

This report presents the 1999 calendar year update of the Air Emission Inventory for the Idaho National Engineering and Environmental Laboratory (INEEL). The INEEL Air Emission Inventory documents sources and emissions of nonradionuclide pollutants from operations at the INEEL. The report describes the emission inventory process and all of the sources at the INEEL, and provides nonradionuclide emissions estimates for stationary sources.

Air Emission Inventory for the Idaho National Engineering and Environmental Laboratory - Calendar Year 1998 Emissions Report

Energy Technology Data Exchange (ETDEWEB)

S. K. Zohner

1999-10-01

This report presents the 1998 calendar year update of the Air Emission Inventory for the Idaho National Engineering and Environmental Laboratory (INEEL). The INEEL Air Emission Inventory documents sources and emissions of nonradionuclide pollutants from operations at the INEEL. The report describes the emission inventory process and all of the sources at the INEEL, and provides nonradiological emissions estimates for stationary sources.

Safety leadership in the teaching laboratories of electrical and electronic engineering departments at Taiwanese Universities.

Science.gov (United States)

Wu, Tsung-Chih

2008-01-01

Safety has always been one of the principal goals in teaching laboratories. Laboratories cannot serve their educational purpose when accidents occur. The leadership of department heads has a major impact on laboratory safety, so this study discusses the factors affecting safety leadership in teaching laboratories. This study uses a mail survey to explore the perceived safety leadership in electrical and electronic engineering departments at Taiwanese universities. An exploratory factor analysis shows that there are three main components of safety leadership, as measured on a safety leadership scale: safety controlling, safety coaching, and safety caring. The descriptive statistics also reveals that among faculty, the perception of department heads' safety leadership is in general positive. A two-way MANOVA shows that there are interaction effects on safety leadership between university size and instructor age; there are also interaction effects between presence of a safety committee and faculty gender and faculty age. It is therefore necessary to assess organizational factors when determining whether individual factors are the cause of differing perceptions among faculty members. The author also presents advice on improving safety leadership for department heads at small universities and at universities without safety committees.

Tri-generation nation

International Nuclear Information System (INIS)

Pichon, Max

2010-01-01

Full text: Sydney and Melbourne councils are looking to outperform each other with ambitious greenhouse and energy efficiency initiatives. Sydney wants to cut CO_2 by 70 per cent by 2030, while Melbourne's 1200 Buildings retrofit project speaks for itself. One key technology both councils are tapping is trigeneration, which generates electricity, heating and cooling from local gas-fired power units. From a physics perspective, a combustion process cannot be more than 30 per cent efficient, so capturing and using the waste heat can lead to great savings. Sydney Lord Mayor Clover Moore said a third of the council's carbon reduction goal of 3.9Mt a year by 2030 will come from tri-gen. Melbourne is aiming to achieve zero net emissions by 2020, which means eliminating 5.8Mt of CO_2, a lot of it through tri-gen. It has already seen a surge among landlords. GPT, Stockland and Mirvac have all stuck tri-gen units in Sydney office developments, while newly carbon- neutral NAB has installed the technology on its data centre in Melbourne and expects to save 20,000 tonnes of CO_2 a year. But one expert, while welcoming the spike in popularity, says there are traps for the unwary. Johnson Controls' Peter Moser sees two core drivers for its uptake. “First is the prominence of GreenStar and NABERS. Many companies will move to tri-gen as they will want the extra points or stars,” he told WME. “Secondly, there is the continuous increase in the price of energy. At the same time there may be an [emissions trading scheme] or a carbon price introduced, and that puts pressure on the consumer. Combining those two scenarios will see more people adopt tri-gen because it will become more economically viable and the payback periods of tri-gen will come down considerably.” But he points to the importance of pre-planning when considering tri-gen, warning. “To put tri-gen into a building, let alone retrofit a whole city and make it work, you need highly complex teams working together

Idaho National Engineering Laboratory materials in inventory natural and enriched uranium management and storage costs

International Nuclear Information System (INIS)

Nebeker, R.L.

1995-11-01

On July 13, 1994, the Office of Environmental Management (EM) was requested to develop a planning process that would result in management policies for dealing with nuclear materials in inventory. In response to this request, EM launched the Materials In Inventory (MIN) Initiative. A Headquarters Working Group was established to develop the broad policy framework for developing MIN management policies. MIN activities cover essentially all nuclear materials within the DOE complex, including such items as spent nuclear fuel, depleted uranium, plutonium, natural and enriched uranium, and other materials. In August 1995, a report discussing the natural and enriched uranium portion of the Initiative for the Idaho National Engineering Laboratory (INEL) was published. That report, 'Idaho National Engineering Laboratory Materials-in-Inventory, Natural and Enriched Uranium'.' identified MIN under the control of Lockheed Idaho Technologies Company at the INEL. Later, additional information related to the costs associated with the storage of MIN materials was requested to supplement this report. This report provides the cost information for storing, disposing, or consolidating the natural and enriched uranium portion of the MIN materials at the INEL. The information consists of eight specific tables which detail present management costs and estimated costs of future activities

Virtual Training Devices Laboratory

Data.gov (United States)

Federal Laboratory Consortium — The Virtual Training Devices (VTD) Laboratory at the Life Cycle Software Engineering Center, Picatinny Arsenal, provides a software testing and support environment...

Biometrics Research and Engineering Laboratory

Data.gov (United States)

Federal Laboratory Consortium — As the Department of Defense moves forward in its pursuit of integrating biometrics technology into facility access control, the Global War on Terrorism and weapon...

Epidemiologic surveillance. Annual report for Idaho National Engineering Laboratory 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-31

Epidemiologic surveillance at DOE facilities consists of regular and systematic collection, analysis, and interpretation of data on absences due to illness and injury in the work force. Its purpose is to provide an early warning system for health problems occurring among employees at participating sites. In this annual report, the 1994 morbidity data for the Idaho National Engineering Laboratory are summarized. These analyses focus on absences of 5 or more consecutive workdays occurring among workers aged 17-85 years. They are arranged in five sets of tables that present: (1) the distribution of the labor force by occupational category and pay status; (2) the absences per person, diagnoses per absence, and diagnosis rates for the whole work force; (3) diagnosis rates by type of disease or injury; (4) diagnosis rates by occupational category; and (5) relative risks for specific types of disease or injury by occupational category.

In situ vitrification program at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Loehr, C.A.; Merrill, S.K.

1991-01-01

A program to demonstrate the viability of in situ vitrification (ISV) technology in remediating a buried mixed transuranic (TRU) waste site is under way at the Idaho National Engineering Laboratory (INEL). The application of the technology to buried waste is being evaluated as part of a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) feasibility study. The ISV thermal treatment process converts contaminated soil into a chemically inert and stable glass and crystalline product. The process uses joule heating, accomplished by applying electric potential to electrodes that are placed in the soil to initiate and maintain soil melting. Organic contaminants in the soil are destroyed or removed while inorganic contaminants, including radionuclides, are incorporated into the stable, glass-like product or volatilized. Off-gases are collected in a confinement hood over the melt area and processed through an off-gas treatment system. The paper illustrates and describes the ISV process

Principles of models based engineering

Energy Technology Data Exchange (ETDEWEB)

Dolin, R.M.; Hefele, J.

1996-11-01

This report describes a Models Based Engineering (MBE) philosophy and implementation strategy that has been developed at Los Alamos National Laboratory`s Center for Advanced Engineering Technology. A major theme in this discussion is that models based engineering is an information management technology enabling the development of information driven engineering. Unlike other information management technologies, models based engineering encompasses the breadth of engineering information, from design intent through product definition to consumer application.

In situ vitrification application to buried waste: Interim report of intermediate field tests at Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Callow, R.A.; Weidner, J.R.; Thompson, L.E.

1991-02-01

This report describes the two in situ vitrification field tests conducted in June and July 1990 at Idaho National Engineering Laboratory. In situ vitrification, an emerging technology for in- place conversion of contaminated soils into a durable glass and crystalline waste form, is being investigated as a potential remediation technology for buried waste. The overall objective of the two tests was to assess the general suitability of the process to remediate waste structures representative of buried waste found at Idaho National engineering Laboratory. In particular, these tests, as part of a treatability study, were designed to provide essential information on the field performance of the process under conditions of significant combustible and metal wastes and to test a newly developed electrode feed technology. The tests were successfully completed, and the electrode feed technology successfully processed the high metal content waste, indicating the process is a feasible technology for application to buried waste

In situ vitrification application to buried waste: Interim report of intermediate field tests at Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Callow, R.A.; Weidner, J.R.; Thompson, L.E.

1991-01-01

This report describes the two in situ vitrification field tests conducted in July and July 1990 at Idaho National Engineering Laboratory. In situ vitrification, an emerging technology for in-place conversion of contaminated soils into a durable glass and crystalline waste form, is being investigated as a potential remediation technology for buried waste. The overall objective of the two tests was to assess the general suitability of the process to remediate waste structures representative of buried waste found at Idaho National Engineering Laboratory. In particular, these tests, as part of a treatability study, were designed to provide essential information field performance of the process under conditions of significant combustible and metal wastes and to test a newly developed electrode feed technology. The tests were successfully completed, and the electrode feed technology successfully processed the high metal content waste, indicating the process is a feasible technology for application to buried waste. 8 refs., 91 figs., 13 tabs

In situ vitrification application to buried waste: Final report of intermediate field tests at Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Callow, R.A.; Weidner, J.R.; Loehr, C.A.; Bates, S.O.; Thompson, L.E.; McGrail, B.P.

1991-08-01

This report describes two in situ vitrification field tests conducted on simulated buried waste pits during June and July 1990 at the Idaho National Engineering Laboratory. In situ vitrification, an emerging technology for in place conversion of contaminated soils into a durable glass and crystalline waste form, is being investigated as a potential remediation technology for buried waste. The overall objective of the two tests was to access the general suitability of the process to remediate waste structures representative of buried waste found at Idaho National Engineering Laboratory. In particular, these tests, as part of a treatability study, were designed to provide essential information on the field performance of the process under conditions of significant combustible and metal wastes and to test a newly developed electrode feed technology. The tests were successfully completed, and the electrode feed technology successfully processed the high metal content waste. Test results indicate the process is a feasible technology for application to buried waste. 33 refs., 109 figs., 39 tabs

ASC Tri-lab Co-design Level 2 Milestone Report 2015

Energy Technology Data Exchange (ETDEWEB)

Hornung, Rich [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Jones, Holger [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Keasler, Jeff [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Neely, Rob [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Pearce, Olga [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hammond, Si [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Trott, Christian [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lin, Paul [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Vaughan, Courtenay [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Cook, Jeanine [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hoekstra, Rob [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bergen, Ben [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Payne, Josh [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Womeldorff, Geoff [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-09-23

In 2015, the three Department of Energy (DOE) National Laboratories that make up the Advanced Sci- enti c Computing (ASC) Program (Sandia, Lawrence Livermore, and Los Alamos) collaboratively explored performance portability programming environments in the context of several ASC co-design proxy applica- tions as part of a tri-lab L2 milestone executed by the co-design teams at each laboratory. The programming environments that were studied included Kokkos (developed at Sandia), RAJA (LLNL), and Legion (Stan- ford University). The proxy apps studied included: miniAero, LULESH, CoMD, Kripke, and SNAP. These programming models and proxy-apps are described herein. Each lab focused on a particular combination of abstractions and proxy apps, with the goal of assessing performance portability using those. Performance portability was determined by: a) the ability to run a single application source code on multiple advanced architectures, b) comparing runtime performance between \

The deep underground science and engineering laboratory at Homestake

Energy Technology Data Exchange (ETDEWEB)

Lesko, Kevin T, E-mail: ktlesko@lbl.go [Department of Physics, University of California Berkeley and Institute for Nuclear and Particle Astrophysics, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, MS 50R5239, Berkeley, CA 94720-8156 (United States)

2009-06-01

The US National Science Foundation and the US underground science community are well into the campaign to establish a world-class, multi-disciplinary deep underground science and engineering laboratory - DUSEL. The NSF's review committee, following the first two NSF solicitations, selected Homestake as the prime site to be developed into an international, multidisciplinary, world-class research facility. Homestake DUSEL will provide much needed underground research space to help relieve the worldwide shortage, particularly at great depth, and will develop research campuses at different depths to satisfy the research requirements for the coming decades. The State of South Dakota has demonstrated remarkable support for the project and has secured the site with the transfer of the former Homestake Gold Mine and has initiated re-entry and rehabilitation of the facility to host a modest interim science program with state funds and those from a substantial philanthropic donor. I review the scientific case for DUSEL and the progress in developing the preliminary design of DUSEL in Homestake and the initial suite of experiments to be funded along with the facility.

Idaho National Engineering and Environmental Laboratory Wildland Fire Management Environmental Assessment - April 2003

Energy Technology Data Exchange (ETDEWEB)

Irving, J.S.

2003-04-30

DOE prepared an environmental assessment (EA)for wildland fire management activities on the Idaho National Engineering and Environmental Laboratory (INEEL) (DOE/EA-1372). The EA was developed to evaluate wildland fire management options for pre-fire, fire suppression, and post fire activities. Those activities have an important role in minimizing the conversion of the native sagebrush steppe ecosystem found on the INEEL to non-native weeds. Four alternative management approaches were analyzed: Alternative 1 - maximum fire protection; Alternative 2 - balanced fire protection; Alternative 2 - balanced fire protection; Alternative 3 - protect infrastructure and personnel; and Alternative 4 - no action/traditional fire protection.

Software Engineering Laboratory (SEL) data base reporting software user's guide and system description. Volume 1: Introduction and user's guide

Science.gov (United States)

1983-01-01

Reporting software programs provide formatted listings and summary reports of the Software Engineering Laboratory (SEL) data base contents. The operating procedures and system information for 18 different reporting software programs are described. Sample output reports from each program are provided.

Laboratory Test of Reciprocating Internal Combustion Engines

Science.gov (United States)

2016-02-04

Control Module (ECM) torque horsepower engine speed boost turbocharger throttle injector power curve...13 2.4 Calibration ............................................................................. 14...Control Units (ECU). Originally, diesel engines were naturally aspirated, but most have evolved to include forced induction devices (turbochargers

Multimedia Software Laboratory | College of Engineering & Applied Science

Science.gov (United States)

Support Milwaukee Engineering Research Conference 2018 Poster Competition Business Corporate Partners Engineer Research Collaborations Corporate Services Product Realization Business Tour Give Entrepreneurship -oriented methods, and performance analysis. Research Message from the Associate Dean Milwaukee Engineerâ

Radiochemistry programme biennial progress report (1986 and 1987)

International Nuclear Information System (INIS)

1988-01-01

This biennial report covers the calendar years 1986 and 1987. This period has seen significant growth in the research activities of the Radiochemistry Programme and this is reflected in this report. The report is organised subject-wise into sections dealing with Fuel Chemistry and Thermodynamics, Sodium Chemistry, Analytical Chemistry and Instrumentation. The major part of the activities of the Radiochemistry Programme relates to fuel chemistry including thermophysical and thermodynamic properties of fuel materials, chemistry of fuel reprocessing and facilities as well as techniques for post-irradiation studies. Sodium chemistry is a smaller but important R and D activity, which has reached full maturity during the period of this report. Analytical chemistry and instrumentation are essential supporting activities. The rapid progress made over the last two years are reflected in the number of items covered in this report. In order to keep the total length of this report under control, the editors had to restrict the individual activities to one or two pages. Though the details of various studies are not presented here, it is hoped that the report gives an overview of the progress made by the Radiochemistry Programme in the last two years. The list of publications given at the end also reflects the growth in research programmes. (author)

Waste Isolation Pilot Plant Biennial Environmental Compliance Report

Energy Technology Data Exchange (ETDEWEB)

Washington Regulatory and Environmental Services

2006-10-12

This Biennial Environmental Compliance Report (BECR) documents compliance with environmental regulations at the Waste Isolation Pilot Plant (WIPP), a facility designed and authorized for the safe disposal of transuranic (TRU) radioactive waste. This BECR covers the reporting period from April 1, 2004, to March 31, 2006. As required by the WIPP Land Withdrawal Act (LWA) (Public Law [Pub. L.] 102-579, as amended by Pub. L. 104-201), the BECR documents United States (U.S.) Department of Energy (DOE) compliance with regulations and permits issued pursuant to the following: (1) Title 40 Code of Federal Regulations (CFR) Part 191, Subpart A, "Environmental Standards for Management and Storage"; (2) Clean Air Act (CAA) (42 United States Code [U.S.C.] §7401, et seq.); (3) Solid Waste Disposal Act (SWDA) (42 U.S.C. §§6901-6992, et seq.); (4) Safe Drinking Water Act (SDWA) (42 U.S.C. §§300f, et seq.); (5) Toxic Substances Control Act (TSCA) (15 U.S.C. §§2601, et seq.); (6) Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) (42 U.S.C. §§9601, et seq.); and all other federal and state of New Mexico laws pertaining to public health and safety or the environment.

Air Emission Inventory for the Idaho National Engineering Laboratory: 1992 emissions report

Energy Technology Data Exchange (ETDEWEB)

Stirrup, T.S.

1993-06-01

This report presents the 1992 Air Emission Inventory for the Idaho National Engineering Laboratory. Originally, this report was in response to the Environmental Oversight and Monitoring Agreement in 1989 between the State of Idaho and the Department of Energy Idaho Field Office, and a request from the Idaho Air Quality Bureau. The current purpose of the Air Emission Inventory is to provide the basis for the preparation of the INEL Permit-to-Operate (PTO) an Air Emission Source Application, as required by the recently promulgated Title V regulations of the Clean Air Act. This report includes emissions calculations from 1989 to 1992. The Air Emission Inventory System, an ORACLE-based database system, maintains the emissions inventory.

Air Emission Inventory for the Idaho National Engineering Laboratory: 1992 emissions report

International Nuclear Information System (INIS)

Stirrup, T.S.

1993-06-01

This report presents the 1992 Air Emission Inventory for the Idaho National Engineering Laboratory. Originally, this report was in response to the Environmental Oversight and Monitoring Agreement in 1989 between the State of Idaho and the Department of Energy Idaho Field Office, and a request from the Idaho Air Quality Bureau. The current purpose of the Air Emission Inventory is to provide the basis for the preparation of the INEL Permit-to-Operate (PTO) an Air Emission Source Application, as required by the recently promulgated Title V regulations of the Clean Air Act. This report includes emissions calculations from 1989 to 1992. The Air Emission Inventory System, an ORACLE-based database system, maintains the emissions inventory

2nd Biennial Conference on Refrigeration for Cryogenic Sensors and Electronic Systems

CERN Document Server

1983-01-01

This proceedings documents the output of the Second Biennial Conference on Refrigeration for Cryogenic Sensors and Electronic Systems held at the National Aeronautics and Space Administration's Goddard Space Flight Center, Greenbelt, Maryland, on December 7-8, 1982. Building on the first open meeting hosted by the National Bureau of Standards in 1980, the focus of this second meeting was again on low-temperature, closed-cycle cooler technology. However, higher temperature coolers (77 K), with technology applicable to the low temperature coolers, were considered to be within the scope of this meeting. This second conference consisted of 30 papers presented by representatives of industry, government, and academia. The conference proceedings reproduced here was published by the NASA Goddard Space Flight Center in Greenbelt Maryland as NASA Conference Publication 2287.

Treatment of the liquid waste of the laboratories of the engineering Department by means of photo catalysis

International Nuclear Information System (INIS)

Porras, Paula; Avalos, Yasmin; Mejia, Gloria; Penuela, Gustavo

2000-01-01

In this paper are showed the results of wastewater treatment of CIA and ISA laboratories of engineering Department. Photo catalysis was used in treatment of wastewater, with a removal between 52% and 68% as chemical oxygen demand (COD) during 6 hours of photo degradation. In photo catalysis, TiO 2 , hydrogen peroxide and ultraviolet light were used

Report of the research results with University of Tokyo Nuclear Engineering Research Laboratory's facilities in fiscal 1975

International Nuclear Information System (INIS)

1976-08-01

Results of the research works by educational institutions using fast neutron source reactor 'Yayoi' etc. of Nuclear Engineering Research Laboratory in fiscal 1975 are reported in individual summaries. Fields of research are the following: shielding benchmark experiment, research on medical irradiation, irradiation experiments, experiments by small research groups, fast neutron streaming experiment, and so on. (Mori, K.)

Development of engineering identity in the engineering curriculum in Dutch higher education : an explorative study from the teaching staff perspective

NARCIS (Netherlands)

Dehing, A.J.M.; Baartman, L.K.J.; Jochems, W.M.G.

2013-01-01

How do engineering students develop a professional identity during the course of the curriculum? What are the development mechanisms and important conditions? In an exploratory study among teachers the authors tried to find out whether the development of engineering identity can be understood by

Overview of environmental surveillance of waste management activities at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Smith, T.H.; Hedahl, T.G.; Wiersma, G.B.; Chew, E.W.; Mann, L.J.; Pointer, T.F.

1986-02-01

The Idaho National Engineering Laboratory (INEL), in southeastern Idaho, is a principal center for nuclear energy development for the Department of Energy (DOE) and the US Nuclear Navy. Fifty-two reactors have been built at the INEL, with 15 still operable. Extensive environmental surveillance is conducted at the INEL by DOE's Radiological and Environmental Sciences Laboratory (RESL), the US Geological Survey (USGS), the National Oceanic and Atmospheric Administration (NOAA), EG and G Idaho, Inc., and Westinghouse Idaho Nuclear Company (WINCO). Surveillance of waste management facilities is integrated with the overall INEL Site surveillance program. Air, water, soil, biota, and environmental radiation are monitored or sampled routinely at the INEL. Results to date indicate very small or no impacts from the INEL on the surrounding environment. Environmental surveillance activities are currently underway to address key environmental issues at the INEL. 7 refs., 6 figs., 2 tabs

Raptors of the Idaho National Engineering Laboratory Site

International Nuclear Information System (INIS)

Craig, T.H.

1979-04-01

From 1974 through 1976 base line data were gathered on the raptors which occur on the Idaho National Engineering Laboratory (INEL) Site. Thirteen species were observed on the INEL Site during the non-breeding seasons. American Rough-legged Hawks, American Kestrels, Golden Eagles, and Prairie Falcons were the most numerous. Marsh Hawks, Ferruginous Hawks, Redtailed Hawks, Swainson's Hawks, Great Horned Owls, Short-eared Owls, Merlins, Cooper's Hawks, the endangered Bald Eagle, and the endangered Peregrine Falcon were all observed on the INEL Site during the nonbreeding seasons although less frequently. American Rough-legged Hawks and American Kestrels were commonly observed in agricultural lands while Prairie Falcons and Golden Eagles were usually seen in areas of native vegetation. Nesting species of raptors on the INEL Site include American Kestrels, and Long-eared Owls. Ferruginous Hawks, Merlins, Prairie Falcons, Red-tailed Hawks, Swainson's Hawks, Golden Eagles, Great Horned Owls, and Burrowing Owls also nest on or near the INEL Site. The nesting ecology of American Kestrels, Long-eared Owls, Prairie Falcons, Red-tailed Hawks, Swainson's Hawks, Golden Eagles, and Great Horned Owls on the INEL Site are summarized in this report. The decline of nesting Ferruginous Hawks, Golden Eagles, and Red-tailed Hawks on and near the INEL Site is discussed

Analytical Laboratory

Data.gov (United States)

Federal Laboratory Consortium — The Analytical Labspecializes in Oil and Hydraulic Fluid Analysis, Identification of Unknown Materials, Engineering Investigations, Qualification Testing (to support...

Design and implementation of a virtual laboratory of radiation measurement

International Nuclear Information System (INIS)

Alvarez T, J. R.; Morales S, J. B.

2009-10-01

The work involves the implementation of a virtual laboratory, this project is conducted in the Faculty of Engineering of National Autonomous University of Mexico with the name of LANUVI. It is intended that the laboratory can be used by students who have interest in the nuclear radiation knowledge as well as in its detection and attenuation, in addition serve as and introduction to nuclear systems. In the first part of project will conduct a source that can simulate the particle radiation of Alfa, beta, neutrons and gamma rays. The project will take sources used in class laboratories and elements that are dangerous but are used in different practical applications. After taking the source analyzing the particles behaviour in different media like air, animal tissue, aluminium, lead, etc. The analysis is done in different ways in order to know with which material can stop or mitigate the different types of radiation. Finally shall be measure radioactivity with different types of detectors. At this point, has the behaviour of ionization chamber but in the future is expected to make the simulation of some other radiation detectors. The mathematical models we represent the behaviour of these cases were implemented in free software. The program will be used to implement the virtual laboratory with radiation sources, detectors and different types of shields will be Blender which is a free software that is used by many users for the embodiment of games but try to use as a tool to help visualize the different equipment that is widely used in a radioactive materials laboratory. (Author)

Buried Transuranic Waste Studies Program at the Idaho National Engineering Laboratory: Annual technology assessment and progress report

International Nuclear Information System (INIS)

Low, J.O.; Allman, D.W.; Shaw, P.G.; Sill, C.W.

1987-01-01

In-situ grouting, an improved-confinement technology that could be applied to the Idaho National Engineering Laboratory (INEL) shallow-land-buried transuranic (TRU) waste, is being investigated by EG and G Idaho, Inc. In situ grouting has been demonstrated as the culmination of a two-year engineering feasibility test at the INEL. In situ stabilization and hydrologic isolation of a simulated buried TRU waste trench at an arid site were performed using an experimental dynamic compaction in situ grouting process developed by Rockwell Hanford Operations (RHO). A series of laboratory evaluations relative to the grout permeation characteristics of microfine particulate cements with INEL-type soil was performed prior to the grouting operations. In addition, an extensive pre-grouting hydrologic assessment of the test trench was performed to support the performance assessment analysis. Laboratory testing of various chemical materials yielded a suitable hydrologic tracer for use in the hydrologic monitoring phase of the experiment. Various plutonium transport laboratory evaluations were performed to assess the plutonium retention capabilities of a microfine grout/INEL-soil waste product similar to that expected to result if the grout is injected in situ into the INEL test trench. The test trench will be hydrologically assessed in FY 1987 to determine if the RHO grouting system attained the performance acceptance criteria of the experiment. The report includes a technology assessment of buried waste technologies developed by other DOE sites. Field demonstrations at ORNL and Hanford are reported under this technology assessment. Also included is information on activities related to buried waste management at the INEL. These include environmental surveillance of the Radioactive Waste Management Complex and the Subsurface Migration Studies Program

Biennial activity report of the Division for PIE and NDT Development [for years] 1989-1990

International Nuclear Information System (INIS)

Babu Rao, C.; Shyamsunder, M.T.; Murugan, S.; Ramabathiran, A.; Rajagopalan, C.; Bhattacharya, D.K.; Kumar, P.V.; Kalyanasundaram, P.; Kasiviswanathan, K.V.

1992-01-01

This is the first biennial report of the Division for Post-Irradiation Examination and Non-Destructive Testing (DPEND) of the Indira Gandhi Centre for Atomic Research, Kalpakkam. It covers the research and development (R and D) activities of the Division during 1989 and 1990. The R and D activities of the Division are both multidisciplinary and interdisciplinary. The principal areas of R and D of DPEND are post-irradiation examination of fuel and structural materials, irradiation experiments, non-destructive evaluation for material characterisation, quality assurance and inservice inspection, failure investigations, remote technology etc. These R and D activities are reported in the form of extended summaries arranged under the headings: research and development in non-destructive evaluation, material characterisation, instrumentation, development of techniques, software development, mechanical equipment and systems (development and commissioning), inspections, and failure analysis. Some of the highlights of these activities are : (1)setting up of a radio metallurgy laboratory with hot cells with recirculating nitrogen gas environment to facilitate post-irradiation examination of the carbide fuel of the Fast Breeder Test Reactor. (FBTR), (2) development of the remote milling and drilling machine and development of pressurised capsules for irradiation creep measurement experiments in FBTR, (b) fabrication of non-destructive testing (NDT) reference standards with controlled defects for use in Nuclear Fuel Complex, Hyderabad. There are a number of appendices listing publications, conference paper, invited talks, internal reports etc. by the scientists of the Division and also awards/prizes won by the scientists. A staff-chart of the Division is also given. (M.G.B.)

Software Development for EECU Platform of Turbofan Engine

Science.gov (United States)

Kim, Bo Gyoung; Kwak, Dohyup; Kim, Byunghyun; Choi, Hee ju; Kong, Changduk

2017-04-01

The turbofan engine operation consists of a number of hardware and software. The engine is controlled by Electronic Engine Control Unit (EECU). In order to control the engine, EECU communicates with an aircraft system, Actuator Drive Unit (ADU), Engine Power Unit (EPU) and sensors on the engine. This paper tried to investigate the process form starting to taking-off and aims to design the EECU software mode and defined communication data format. The software is implemented according to the designed software mode.

Conference handbook. Seventh Conference on Nuclear Science and Engineering in Australia

International Nuclear Information System (INIS)

2007-01-01

The Australian Nuclear Association (ANA) inaugurated a series of biennial national conferences in 1995 to be held in alternate years to the series of international Pacific Basin Nuclear Conferences, of which the ANA hosted the Ninth in the series in Sydney in May 1994 and the Fifteenth in Sydney in 2006. The main objective of these national conferences is to present information on important aspects of the peaceful uses of nuclear science and engineering in Australia and to place this information in a world context and in a readily understood form. These conferences have the general title of Nuclear Science and Engineering in Australia and have consisted mainly of papers invited from leading experts in areas of topical interest in nuclear science and technology supported by contributed poster papers. This seventh conference in 2007 has the special theme A Nuclear Future and also includes papers by invited speakers and contributed posters

The American Society for Clinical Pathology's 2014 vacancy survey of medical laboratories in the United States.

Science.gov (United States)

Garcia, Edna; Ali, Asma M; Soles, Ryan M; Lewis, D Grace

2015-09-01

To determine the extent and distribution of workforce shortages within the nation's medical laboratories. Historically, the results of this biennial survey have served as a basis for additional research on laboratory recruitment, retention, education, marketing, certification, and advocacy. The 2014 Vacancy Survey was conducted through collaboration between American Society for Clinical Pathology's Institute of Science, Technology, and Policy in Washington, DC, and the Evaluation, Measurement, and Assessment Department and Board of Certification in Chicago, Illinois. Data were collected via an Internet survey that was distributed to individuals who were able to report on staffing and certifications for their laboratories. Data reveal increased overall vacancy rates since 2012 for all departments surveyed except cytology and cytogenetics. Also, results show higher anticipated retirement rates for both staff and supervisors. Overall certification rates are highest among laboratory personnel in cytogenetics, hematology/coagulation, and flow cytometry departments and lowest among phlebotomy, specimen processing, and anatomic pathology. Factors such as retirement and the improving economy are driving the need for more laboratory professionals. Recruitment of qualified laboratory professionals in the workforce and students in laboratory programs will be the key in fulfilling the higher vacancies revealed from the survey results in 2014. Copyright© by the American Society for Clinical Pathology.

The Environmental Compliance Office at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Cooper, S.C.

1990-01-01

The Idaho Operations Office of the U.S. Department of Energy (DOE-ID) has established an Environmental Compliance Office (ECO) at the Idaho National Engineering Laboratory (INEL). This office has been formed to ensure that INEL operations and activities are in compliance with all applicable environmental state and federal regulations. The ECO is headed by a DOE-ID manager and consists of several teams, each of which is led by a DOE-ID employee with members from DOE-ID, from INEL government contractors, and from DOE-ID consultants. The teams are (a) the negotiated compliance team, (b) the compliance implementation team (CIT), (c) the permits team, (d) the interagency agreement (IAG) team, (e) the consent order and compliance agreement (COCA) oversight team, and (f) the National Environmental Policy Act (NEPA) team. The last two teams were short term and have already completed their respective assignments. The functions of the teams and the results obtained by each are discussed

A summary of the environmental restoration program retrieval demonstration project at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

McQuary, J.

1991-02-01

This report provides a summary of the Environmental Restoration Program's Retrieval Demonstration Project at the Idaho National Engineering Laboratory. This project developed concepts for demonstrating facilities and equipment for the retrieval of buried transuranic mixed waste at the INEL. Included is a brief assessment of the viability, cost effectiveness, and safety of retrieval based on the developed concept. Changes made in Revision 1 reflect editorial changes only. 31 refs., 1 fig

Try and try again--qualitative insights into adolescent smoking experimentation and notions of addiction.

Science.gov (United States)

Leavy, Justine; Wood, Lisa; Phillips, Fiona; Rosenberg, Michael

2010-12-01

addiction is a relatively unexplored issue in youth tobacco control. Increasingly, there is recognition of addiction experiences in regular and irregular teenage smokers. Research was undertaken on behalf of the Smarter than Smoking (STS) project to probe young people's reasons for smoking uptake, their attitudes towards the social acceptability of smoking, predictors of continued smoking after trial and understandings and perceptions of addiction. twenty focus groups were conducted to collect qualitative data from young people (n=92) aged 13 to 15 years from metropolitan and regional areas of Western Australia (WA), from a variety of socioeconomic backgrounds, including young Aboriginal and Torres Strait Islander people. of the young people spoken to, 20% smoked regularly, 40% had tried smoking and 40% had never tried. Acceptability and normalcy of trialling smoking was a recurring theme, with little perceived risk of trial leading to regular smoking or becoming addicted. Even non-smokers accepted 'just having a try' in the context of curiosity, life experiences and 'informed choice'. preventing continuation after trial of smoking among young people needs to increase in importance, given the prevailing norms around 'trying it' and individual choice.

Idaho National Engineering and Environmental Laboratory institutional plan -- FY 2000--2004

Energy Technology Data Exchange (ETDEWEB)

Enge, R.S.

1999-12-01

In this first institutional plan prepared by Bechtel BWXT Idaho, LLC, for the Idaho National Engineering and Environmental Laboratory, the INEEL will focus its efforts on three strategic thrusts: (1) Environmental Management stewardship for DOE-EM, (2) Nuclear reactor technology for DOE-Nuclear Energy (NE), and (3) Energy R and D, demonstration, and deployment (initial focus on biofuels and chemicals from biomass). The first strategic thrust focuses on meeting DOE-EMs environmental cleanup and long-term stewardship needs in a manner that is safe, cost-effective, science-based, and approved by key stakeholders. The science base at the INEEL will be further used to address a grand challenge for the INEEL and the DOE complex--the development of a fundamental scientific understanding of the migration of subsurface contaminants. The second strategic thrust is directed at DOE-NEs needs for safe, economical, waste-minimized, and proliferation-resistant nuclear technologies. As NE lead laboratories, the INEEL and ANL will pursue specific priorities. The third strategic thrust focuses on DOE's needs for clean, efficient, and renewable energy technology. As an initial effort, the INEEL will enhance its capability in biofuels, bioprocessing, and biochemicals. The content of this institutional plan is designed to meet basic DOE requirements for content and structure and reflect the key INEEL strategic thrusts. Updates to this institutional plan will offer additional content and resource refinements.

[Development of domain specific search engines].

Science.gov (United States)

Takai, T; Tokunaga, M; Maeda, K; Kaminuma, T

2000-01-01

As cyber space exploding in a pace that nobody has ever imagined, it becomes very important to search cyber space efficiently and effectively. One solution to this problem is search engines. Already a lot of commercial search engines have been put on the market. However these search engines respond with such cumbersome results that domain specific experts can not tolerate. Using a dedicate hardware and a commercial software called OpenText, we have tried to develop several domain specific search engines. These engines are for our institute's Web contents, drugs, chemical safety, endocrine disruptors, and emergent response for chemical hazard. These engines have been on our Web site for testing.

Promoting Girls' Awareness and Interest in Engineering

Science.gov (United States)

Lawrence, Deborah A.; Mancuso, Tina A.

2012-01-01

Multiple initiatives have been launched to try to widen the pipeline for women to enter engineering careers, including reviews of gender differences in enrollment in technology and pre-engineering courses from middle school through doctoral degrees. National agencies have also studied some of the social and cultural forces at play with regard to…

DIC-CAM recipe for reverse engineering

Science.gov (United States)

Romero-Carrillo, P.; Lopez-Alba, E.; Dorado, R.; Diaz-Garrido, F. A.

2012-04-01

Reverse engineering (RE) tries to model and manufacture an object from measurements one of a reference object. Modern optical measurement systems and computer aided engineering software have improved reverse engineering procedures. We detail the main RE steps from 3D digitalization by Digital Image Correlation to manufacturing. The previous description is complemented with an application example, which portrays the performance of RE. The differences between original and manufactured objects are less than 2 mm (close to the tool radius).

Environmental monitoring for EG and G Idaho facilities at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Tkachyk, J.W.; Wright, K.C.; Wilhelmsen, R.N.

1990-08-01

This report describes the 1989 environmental-monitoring activities of the Environmental Monitoring Unit of EG ampersand G Idaho, Inc., at EG ampersand G-operated facilities at the Idaho National Engineering Laboratory (INEL). The major facilities monitored include the Radioactive Waste Management Complex, the Waste Experimental Reduction Facility, the Mixed Waste Storage Facility, and two surplus facilities. Additional monitoring activities performed by Environmental Monitoring are also discussed, including drinking-water monitoring and nonradiological liquid-effluent monitoring, as well as data management. The primary purposes of monitoring are to evaluate environmental conditions and to provide and interpret data, in compliance with applicable regulations, to ensure protection of human health and the environment. This report compares 1989 environmental-monitoring data with derived concentration guides and with data from previous years. This report also presents results of sampling performed by the Radiological and Environmental Sciences Laboratory and by the United States Geological Survey. 17 refs., 49 figs., 11 tabs

Integrated Support Environment (ISE) Laboratory

Data.gov (United States)

Federal Laboratory Consortium — Purpose:The Integrated Support Environment (ISE) Laboratory serves the fleet, in-service engineers, logisticians and program management offices by automatically and...

An overview of environmental surveillance of waste management activities at the Idaho National Engineering Laboratory

Science.gov (United States)

Smith, T.H.; Chew, E.W.; Hedahl, T.G.; Mann, L.J.; Pointer, T.F.; Wiersma, G.B.

1986-01-01

The Idaho National Engineering Laboratory (INEL), in southeastern Idaho, is a principal center for nuclear energy development for the Department of Energy (DOE) and the U.S. Nuclear Navy. Fifty-two reactors have been built at the INEL, with 15 still operable. Extensive environmental surveillance is conducted at the INEL by DOE's Radiological Environmental Sciences Laboratory (RESL), and the U.S. Geological Survey (USGS), the National Oceanic and Atmospheric Administration (NOAA), EG&G Idaho, Inc., and Westinghouse Idaho Nuclear Company (WINCO). Surveillance of waste management facilities radiation is integrated with the overall INEL Site surveillance program. Air, warer, soil, biota, and environmental radiation are monitored or sampled routinely at INEL. Results to date indicate very small or no impacts from INEL on the surrounding environment. Environmental surveillance activities are currently underway to address key environmental issues at the INEL.

Expository Versus Simulated Laboratory in Teaching Professional ...

African Journals Online (AJOL)

In Nigeria Polytechnics, demonstrating theories through practical and laboratory experiments is an important approach to teaching, especially in engineering curricula. Often, lack of interest, resources and logistics problems makes this impossible. Evidence suggests that the expository laboratory, as used in engineering ...

Science | Argonne National Laboratory

Science.gov (United States)

Security Photon Sciences Physical Sciences & Engineering Energy Frontier Research Centers Scientific Publications Researchers Postdocs Exascale Computing Institute for Molecular Engineering at Argonne Work with Us About Safety News Careers Education Community Diversity Directory Argonne National Laboratory

Status of the nation's local mass transportation: performance and conditions. Report to the congress, June 1988. Biennial report

Energy Technology Data Exchange (ETDEWEB)

1988-06-01

This document is the third biennial Report of the Secretary of Transportation to the United States Congress on the current performance and condition of the Nation's public mass-transportation systems. It updates the information and recommendations of the previous report and should be of value to the Congress and the Department for developing policy and program requirements to administer the Federal mass-transportation assistance program.

Advances in engineering nanometrology at the National Physical Laboratory

Science.gov (United States)

Leach, Richard K.; Claverley, James; Giusca, Claudiu; Jones, Christopher W.; Nimishakavi, Lakshmi; Sun, Wenjuan; Tedaldi, Matthew; Yacoot, Andrew

2012-07-01

The National Physical Laboratory, UK, has been active in the field of engineering nanometrology for a number of years. A summary of progress over the last five years is presented in this paper and the following research projects discussed in detail. (1) Development of an infrastructure for the calibration of instruments for measuring areal surface topography, along with the development of areal software measurement standards. This work comprises the use of the optical transfer function and a technique for the simultaneous measurement of topography and the phase change on reflection, allowing composite materials to be measured. (2) Development of a vibrating micro-CMM probe with isotropic probing reaction and the ability to operate in a non-contact mode. (3) A review of x-ray computed tomography and its use in dimensional metrology. (4) The further development of a metrology infrastructure for atomic force microscopy and the development of an instrument for the measurement of the effect of the probe-surface interaction. (5) Traceable measurement of displacement using optical and x-ray interferometry to picometre accuracy. (6) Development of an infrastructure for low-force metrology, including the development of appropriate transfer artefacts.

Advances in engineering nanometrology at the National Physical Laboratory

International Nuclear Information System (INIS)

Leach, Richard K; Claverley, James; Giusca, Claudiu; Jones, Christopher W; Nimishakavi, Lakshmi; Sun, Wenjuan; Tedaldi, Matthew; Yacoot, Andrew

2012-01-01

The National Physical Laboratory, UK, has been active in the field of engineering nanometrology for a number of years. A summary of progress over the last five years is presented in this paper and the following research projects discussed in detail. (1) Development of an infrastructure for the calibration of instruments for measuring areal surface topography, along with the development of areal software measurement standards. This work comprises the use of the optical transfer function and a technique for the simultaneous measurement of topography and the phase change on reflection, allowing composite materials to be measured. (2) Development of a vibrating micro-CMM probe with isotropic probing reaction and the ability to operate in a non-contact mode. (3) A review of x-ray computed tomography and its use in dimensional metrology. (4) The further development of a metrology infrastructure for atomic force microscopy and the development of an instrument for the measurement of the effect of the probe–surface interaction. (5) Traceable measurement of displacement using optical and x-ray interferometry to picometre accuracy. (6) Development of an infrastructure for low-force metrology, including the development of appropriate transfer artefacts. (paper)

ROLE OF COMPUTER ORIENTED LABORATORY TRAINING COURSE IN PHYSICS FOR DEVELOPMENT OF KEY COMPETENCES OF FUTURE ENGINEERS

Directory of Open Access Journals (Sweden)

Iryna Slipukhina

2014-06-01

Full Text Available In the article the features of the core competencies, which are formed in the course study of Physics at the Technical University are described. Some features and examples of the use of computer-oriented laboratory work for the formation of technological competencies engineering students are highlighted. Definitely possible elements of interactive content notebook integrated with software analysis of the experimental data.

Development of Servo Motor Trainer for Basic Control System in Laboratory of Electrical Engineering Control System Faculty of Engineering Universitas Negeri Surabaya

Science.gov (United States)

Endryansyah; Wanarti Rusimamto, Puput; Ridianto, Adam; Sugiarto, Hariyadi

2018-04-01

In the Department of Electrical Engineering FT Unesa, there are 3 majors: S1 Electrical Engineering Education, S1 Electrical Engineering, and D3 Electrical Engineering. Courses the Basic System Settings go to in the curriculum of the three programs. Team lecturer college of basic system settings seek learning innovation, focused on the development of trainer to student practicum at the laboratory of systems control. Trainer developed is a servo motor along with the lab module that contains a wide variety of theories about the servo motor and guide the practicum. This research type is development research using methods Research & development (R & D). In which the steps are applied in this study is as follows: pay attention to the potential and existing problems, gather information and study the literature, design the product, validate the design, revise the design, a limited trial. The results of the validation of learning device in the form of modules and trainer obtained as follows: score validation of learning device is 3,64; score validation lab module Servo Motor is 3,47; and questionnaire responses of students is 3,73. The result of the whole validation value is located in the interval >of 3.25 s/d 4 with the category of “Very Valid”, so it can be concluded that all instruments have a level of validity “Very Valid” and worthy of use for further learning.

Enhancements to the Idaho National Engineering Laboratory motor-operated valve assessment software

International Nuclear Information System (INIS)

Holbrook, M.R.; Watkins, J.C.

1994-01-01

In January 1991, the U.S. Nuclear Regulatory Commission (USNRC) commenced Part 1 inspections to review licensee's motor-operated valve (MOV) programs that were developed to address Generic Letter 89-10, open-quotes Safety-Related Motor-Operated Valve Testing and Surveillanceclose quotes. In support, of this effort, the Isolation Valve Assessment (IVA) software, Version 3.10, was developed by the Idaho National Engineering Laboratory (INEL) to enable rapid in-depth review of MOV sizing and torque switch setting calculations. In 1994, the USNRC commenced Part 2 inspections, which involve a more in-depth review of MOV in situ testing relative to design-basis assumptions. The purpose of this paper is to describe the latest INEL and industry research that has been incorporated into Version 4.00 of the IVA software to support the latest round of inspections. Major improvements include (a) using dynamic and static test results to determine MOV performance parameters and validate design-basis engineering assumptions, (b) determining the stem/stem-nut coefficient of friction using new research-based techniques, (c) adding the ability to evaluate globe valves, and (d) incorporating new methods to account for the effects of high ambient temperature on the output torque of alternating current (ac) motors

Source Release Modeling for the Idaho National Engineering and Environmental Laboratory's Subsurface Disposal Area

International Nuclear Information System (INIS)

Becker, B.H.

2002-01-01

A source release model was developed to determine the release of contaminants into the shallow subsurface, as part of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) evaluation at the Idaho National Engineering and Environmental Laboratory's (INEEL) Subsurface Disposal Area (SDA). The output of the source release model is used as input to the subsurface transport and biotic uptake models. The model allowed separating the waste into areas that match the actual disposal units. This allows quantitative evaluation of the relative contribution to the total risk and allows evaluation of selective remediation of the disposal units within the SDA

Synergistic Extraction of Lactic Acid with Tri-n-Octylamine and Try-n-Butylphosphate

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, Michiaki.; Yuba, Seiji.; Kondo, Kazuo. (Doshisha University, Department of Chemical Engineering and Materials Science (Japan))

1998-12-01

Synergistic extraction system of lactic acid is examined to develop to in situ extractive fermentation process. The addition of try-n-butyl phosphate(TBP) to the extraction system of lactic acid(HA) with tri-n-actylamine(TOA) diluted by hexane causes a large synergism. Extraction reaction with the mixed extractant is interpreted quite well based on the formation of mixed complex, HA[center dot]TOA[center dot]2TBP. Though the addition of hexane solution containing TBP and TOA to the culture of Lactobacillus rhamnosus results in low lactate production, some lactate is produced. (author)

Synergistic Extraction of Lactic Acid with Tri-n-Octylamine and Try-n-Butylphosphate

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, Michiaki.; Yuba, Seiji.; Kondo, Kazuo. [Doshisha University, Department of Chemical Engineering and Materials Science (Japan)

1998-12-01

Synergistic extraction system of lactic acid is examined to develop to in situ extractive fermentation process. The addition of try-n-butyl phosphate(TBP) to the extraction system of lactic acid(HA) with tri-n-actylamine(TOA) diluted by hexane causes a large synergism. Extraction reaction with the mixed extractant is interpreted quite well based on the formation of mixed complex, HA{center_dot}TOA{center_dot}2TBP. Though the addition of hexane solution containing TBP and TOA to the culture of Lactobacillus rhamnosus results in low lactate production, some lactate is produced. (author)

Analysis of the design and economics of molten carbonate fuel cell tri-generation systems providing heat and power for commercial buildings and H2 for FC vehicles

Science.gov (United States)

Li, Xuping; Ogden, Joan; Yang, Christopher

2013-11-01

This study models the operation of molten carbonate fuel cell (MCFC) tri-generation systems for “big box” store businesses that combine grocery and retail business, and sometimes gasoline retail. Efficiency accounting methods and parameters for MCFC tri-generation systems have been developed. Interdisciplinary analysis and an engineering/economic model were applied for evaluating the technical, economic, and environmental performance of distributed MCFC tri-generation systems, and for exploring the optimal system design. Model results show that tri-generation is economically competitive with the conventional system, in which the stores purchase grid electricity and NG for heat, and sell gasoline fuel. The results are robust based on sensitivity analysis considering the uncertainty in energy prices and capital cost. Varying system sizes with base case engineering inputs, energy prices, and cost assumptions, it is found that there is a clear tradeoff between the portion of electricity demand covered and the capital cost increase of bigger system size. MCFC Tri-generation technology provides lower emission electricity, heat, and H2 fuel. With NG as feedstock the CO2 emission can be reduced by 10%-43.6%, depending on how the grid electricity is generated. With renewable methane as feedstock CO2 emission can be further reduced to near zero.

Ranking protective coatings: Laboratory vs. field experience

Science.gov (United States)

Conner, Jeffrey A.; Connor, William B.

1994-12-01

Environmentally protective coatings are used on a wide range of gas turbine components for survival in the harsh operating conditions of engines. A host of coatings are commercially available to protect hot-section components, ranging from simple aluminides to designer metallic overlays and ceramic thermal barrier coatings. A variety of coating-application processes are available, and they range from simple pack cementation processing to complex physical vapor deposition, which requires multimillion dollar facilities. Detailed databases are available for most coatings and coating/process combinations for a range of laboratory tests. Still, the analysis of components actually used in engines often yields surprises when compared against predicted coating behavior from laboratory testing. This paper highlights recent work to develop new laboratory tests that better simulate engine environments. Comparison of in-flight coating performance as well as industrial and factory engine testing on a range of hardware is presented along with laboratory predictions from standard testing and from recently developed cyclic burner-rig testing.

Engineering students' sustainability approaches

Science.gov (United States)

Haase, S.

2014-05-01

Sustainability issues are increasingly important in engineering work all over the world. This article explores systematic differences in self-assessed competencies, interests, importance, engagement and practices of newly enrolled engineering students in Denmark in relation to environmental and non-environmental sustainability issues. The empirical base of the article is a nation-wide, web-based survey sent to all newly enrolled engineering students in Denmark commencing their education in the fall term 2010. The response rate was 46%. The survey focused on a variety of different aspects of what can be conceived as sustainability. By means of cluster analysis, three engineering student approaches to sustainability are identified and described. The article provides knowledge on the different prerequisites of engineering students in relation to the role of sustainability in engineering. This information is important input to educators trying to target new engineering students and contribute to the provision of engineers equipped to meet sustainability challenges.

News | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Contact | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

FAQ's | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Community | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Tutoring | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Scholarships | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Donate | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Industrial & Manufacturing Engineering | Classification | College of

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Alumni | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Advising | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Design, Simulation and Experimental Evaluation of Tri-Phasic Piezoelectric Composite Transducers

Science.gov (United States)

Tamez, Juan Pedro

-phasic transducer to improve the Figures of Merit (FOM) for non-destructive evaluation (NDE) applications. iv. Explore the performance of the diphasic and tri-phasic transducer for energy harvesting applications. v. Perform analysis and quantification of the transducers in a laboratory environment to analyze their performance for Non-Destructive Testing (NDE) using pulse echo acoustics and Electro-Mechanical Impedance (EMI) measurements. The findings of this research are reported in this dissertation indicate that the measured piezoelectric properties of the fabricated tri-phasic transducers are in good agreement with those of the predicted designs. The simulation of the designed transducer has acoustic energy channeled in the d33 mode at resonance, with weak or no shear mode cross talk behavior from the other modes. The mechanical displacements measured were large and highly aligned along polar direction consistent with d33 mode. This implies that multiphasic piezoelectric transducer performs as a single device with improved mechanical and electrical response for sensing, actuation or single device transducer applications. Testing in a laboratory environment demonstrated that they can be highly useful for both the contact and air coupled noncontact Non-Destructive Evaluation (NDE) and nondestructive testing (NDT) applications.

Vadose zone monitoring at the radioactive waste management complex, Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

McElroy, D.L.; Hubbell, J.M.

1989-01-01

A network of vadose zone instruments was installed in surficial sediments and sedimentary interbeds beneath the Radioactive Waste Management Complex (RWMC) of the Idaho National Engineering Laboratory. The network of instruments monitor moisture movement in a heterogeneous geologic system comprised of sediments which overlie and are intercalated with basalt flows. The general range of matric potentials in the surficial sediments (0 to 9.1 m) was from saturation to -3 bars. The basalt layer beneath the surficial sediments impedes downward water movement. The general range of matric potentials in the 9-, 34- and 73-m interbeds was from -0.3 to 1.7 bars. Preliminary results indicated downward moisture movement through the interbeds. 8 refs., 9 figs., 1 tab

Boiling water reactor containment modeling and analysis at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Holcomb, E.E. III; Wilson, G.E.

1984-01-01

Under the auspices of the United States Nuclear Regulatory Commission, severe accidents are being studied at the Idaho National Engineering Laboratory. The boiling water reactor (BWR) studies have focused on postulated anticipated transients without scram (ATWS) accidents which might contribute to severe core damage or containment failure. A summary of the containment studies is presented in the context of the analytical tools (codes) used, typical transient simulation results and the need for prototypical containment data. All of these are related to current and future analytical capabilities. It is shown that torus temperatures during the ATWS depart from limiting conditions for BWR T-quencher operation, outside of which stable steam condensation has not been proven

Incinerator development program for processing transuranic waste at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Hedahl, T.G.

1982-01-01

In the fall of 1981, two short-term tests were conducted on a controlled air and a rotary kiln incinerator to assess their potential for processing transuranic (TRU) contaminated waste at the Idaho National Engineering Laboratory (INEL). The primary purpose of the test program was a proof-of-principle verification that the incinerators could achieve near-complete combustion of the combustible portion of the waste, while mixed with high percentages of noncombustible and metal waste materials. Other important test objectives were to obtain system design information including off-gas and end-product characteristics and incinerator operating parameters. Approximately 7200 kg of simulated (non-TRU) waste from the INEL were processed during the two tests

AFSC/RACE/GAP/Palsson: Gulf of Alaska and Aleutian Islands Biennial Bottom Trawl Survey estimates of catch per unit effort, biomass, population at length, and associated tables

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The GOA/AI Bottom Trawl Estimate database contains abundance estimates for the Alaska Biennial Bottom Trawl Surveys conducted in the Gulf of Alaska and the Aleutian...

Commercial disposal options for Idaho National Engineering Laboratory low-level radioactive waste

International Nuclear Information System (INIS)

Porter, C.L.; Widmayer, D.A.

1995-09-01

The Idaho National Engineering Laboratory (INEL) is a Department of Energy (DOE)-owned, contractor-operated site. Significant quantities of low-level radioactive waste (LLW) have been generated and disposed of onsite at the Radioactive Waste Management Complex (RWMC). The INEL expects to continue generating LLW while performing its mission and as aging facilities are decommissioned. An on-going Performance Assessment process for the RWMC underscores the potential for reduced or limited LLW disposal capacity at the existing onsite facility. In order to properly manage the anticipated amount of LLW, the INEL is investigating various disposal options. These options include building a new facility, disposing the LLW at other DOE sites, using commercial disposal facilities, or seeking a combination of options. This evaluation reports on the feasibility of using commercial disposal facilities

Engineering Water Analysis Laboratory Activity.

Science.gov (United States)

Schlenker, Richard M.

The purposes of water treatment in a marine steam power plant are to prevent damage to boilers, steam-operated equipment, and steam and condensate lives, and to keep all equipment operating at the highest level of efficiency. This laboratory exercise is designed to provide students with experiences in making accurate boiler water tests and to…

Structural performance of the DOE's Idaho National Engineering Laboratory during the 1983 Borah Peak Earthquake

International Nuclear Information System (INIS)

Guenzler, R.C.; Gorman, V.W.

1985-01-01

The 1983 Borah Peak Earthquake (7.3 Richter magnitude) was the largest earthquake ever experienced by the DOE's Idaho National Engineering Laboratory (INEL). Reactor and plant facilities are generally located about 90 to 110 km (60 miles) from the epicenter. Several reactors were operating normally at the time of the earthquake. Based on detailed inspections, comparisons of measured accelerations with design levels, and instrumental seismograph information, it was concluded that the 1983 Borah Peak Earthquake created no safety problems for INEL reactors or other facilities. 10 references, 16 figures, 2 tables

Supporting Data Amended FY 1992/FY 1993 Biennial Budget Estimate Submitted to Congress - January 1992. Descriptive Summaries of the Research, Development, Test and Evaluation, Army Appropriation

Science.gov (United States)

1992-01-01

dessert and snack items to increase acceptability and 31$,) UNCLASSIFIED UNCLASSIFIED AMENDED FY 1992/1993 BIENNIAL RDTE DESCRIPTIVE SUMMARY Program...Planned Program: " (U) Finalize development of non-organic and non-polluting processing bids for extruded and molded energetic materials * (U

Systems Engineering as a tool; Verktoeyet Systems Engineering : struktur fra start til maal

Energy Technology Data Exchange (ETDEWEB)

Carlsen, Randi

2002-07-01

Systems engineering integrates all types of specialists and disciplines into teams that try to create a structured development process from concept via production to operation. The idea is that by using systems engineering, projects can be completed efficiently and successfully. It is important that the individual participant in a project understands that he or she works within a system and that there is a need for skill, comprehensiveness and communication. Systems engineering comprises system design, computer aided design, cybernetics and mecatronics. The article describes the use of systems engineering in a student project in which a heat pump will be used to utilize the energy potential of ground water primarily to heat the visitors' area in a mine museum in Kongsberg, Norway.

An Analog Computer for Electronic Engineering Education

Science.gov (United States)

Fitch, A. L.; Iu, H. H. C.; Lu, D. D. C.

2011-01-01

This paper describes a compact analog computer and proposes its use in electronic engineering teaching laboratories to develop student understanding of applications in analog electronics, electronic components, engineering mathematics, control engineering, safe laboratory and workshop practices, circuit construction, testing, and maintenance. The…

Engineering Design vs. Artistic Design: Some Educational Consequences

Science.gov (United States)

Eder, Wolfgang Ernst

2013-01-01

"Design" can be a noun, or a verb. Six paths for research into engineering design (as verb) are identified, they must be coordinated for internal consistency and plausibility. Design research tries to clarify design processes and their underlying theories--for designing in general, and for particular forms, e.g., design engineering. Theories are a…

Hydrology of the solid waste burial ground as related to potential migration of radionuclides, Idaho National Engineering Laboratory

Science.gov (United States)

Barraclough, Jack T.; Robertson, J.B.; Janzer, V.J.; Saindon, L.G.

1976-01-01

A study was made (1970-1974) to evaluate the geohydrologic and geochemical controls on subsurface migration of radionuclides from pits and trenches in the Idaho National Engineering Laboratory (INEL) solid waste burial ground and to determine the existence and extent of radionuclide migration from the burial ground. A total of about 1,700 sediment, rock, and water samples were collected from 10 observation wells drilled in and near the burial ground of Idaho National Engineering Laboratory, formerly the National Reactor Testing Station (NRTS). Within the burial ground area, the subsurface rocks are composed principally of basalt. Wind- and water-deposited sediments occur at the surface and in beds between the thicker basalt zones. Two principal sediment beds occur at about 110 feet and 240 feet below the land surface. The average thickness of the surficial sedimentary layer is about 15 feet while that of the two principal subsurface layers is 13 and 14 feet, respectively. The water table in the aquifer beneath the burial ground is at a depth of about 580 feet. Fission, activation, and transuranic elements were detected in some of the samples from the 110- and 240-foot sedimentary layers. (Woodard-USGS)

1975 progress report: Idaho National Engineering Laboratory site radioecology--ecology programs

International Nuclear Information System (INIS)

Markham, O.D.

1976-06-01

Results are reported from measurements of the content of various radionuclides in the tissues of wild animals on or near the Idaho National Engineering Laboratory sampled during 1975. Tissue samples from antelope, waterfowl, rodents, rabbits, and doves were analyzed for 13 radionuclides, including 134 Cs, 137 Cs, 95 Zr, 95 Nb, 103 Ru, 238 Pu, 239 Pu, 90 Sr, 131 I, and 60 Co which were responsible for the largest amounts of radioactivity. Measurements were also made of the content of 238 Pu, 239 Pu, and 241 Am in soil samples and the radioactivity in tumbling weeds at the radioactive waste management site. Data are included from studies on the ecology of the pygmy rabbit, Salvilagus idahoensis, amphibians, reptiles, birds of prey, rodents, and coyotes, and vegetation in relation to land use at the site. Seasonal variations in the deposition and retention of 141 Ce and 134 Cs on sagebrush and bottlebrush grass were compared

Thermal treatment technology at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Hillary, J.M.

1994-01-01

Recent surveys of mixed wastes in interim storage throughout the 30-site Department of Energy complex indicate that only 12 of those sites account for 98% of such wastes by volume. Current inventories at the Idaho National Engineering Laboratory (INEL) account for 38% of total DOE wastes in interim storage, the largest of any single site. For a large percentage of these waste volumes, as well as the substantial amounts of buried and currently generated wastes, thermal treatment processes have been designated as the technologies of choice. Current facilities and a number of proposed strategies exist for thermal treatment of wastes of this nature at the INEL. High-level radioactive waste is solidified in the Waste Calciner Facility at the Idaho Central Processing Plant. Low-level solid wastes until recently have been processed at the Waste Experimental Reduction Facility (WERF), a compaction, size reduction, and controlled air incineration facility. WERF is currently undergoing process upgrading and RCRA Part B permitting. Recent systems studies have defined effective strategies, in the form of thermal process sequences, for treatment of wastes of the complex and heterogeneous nature in the INEL inventory. This presentation reviews the current status of operating facilities, active studies in this area, and proposed strategies for thermal treatment of INEL wastes

The Deep Underground Science and Engineering Laboratory at Homestake

Energy Technology Data Exchange (ETDEWEB)

Lesko, Kevin T [Department of Physics, University of California Berkeley and the Institute for Nuclear and Particle Astrophysics, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, MS50R5239, Berkeley, CA 94720-8146 (United States)], E-mail: KTLesko@lbl.gov

2008-11-01

The National Science Foundation and the international underground science community are well into establishing a world-class, multidisciplinary Deep Underground Science and Engineering Laboratory (DUSEL) at the former Homestake mine in Lead South Dakota. The NSF's review committee, following the first two NSF solicitations, selected the Homestake Proposal and site as the prime location to be developed into an international research facility. Homestake DUSEL will provide much needed underground research space to help relieve the worldwide shortage, particularly at great depth, and will develop research campuses at several different depths to satisfy the research requirements for the coming decades. The State of South Dakota has demonstrated remarkable support for the project and has secured the site with the transfer from the Homestake Mining Corp. The State, through its Science and Technology Authority with state funds and those of a philanthropic donor has initiated rehabilitation of the surface and underground infrastructure including the Ross and Yates hoists accessing the 4850 Level (feet below ground, 4100 to 4200 mwe). The scientific case for DUSEL and the progress in establishing the preliminary design of the facility and the associated suite of experiments to be funded along with the facility by the NSF are presented.

The Australian Institute of Nuclear Science and Engineering - a model for university-national laboratory collaboration

International Nuclear Information System (INIS)

Gammon, R.B.

1994-01-01

This paper describes the aims and activities of the Australian Institute of Nuclear Science and Engineering (AINSE), from its foundation in 1958 through to 1993. The philosophy, structure and funding of the Institute are briefly reviewed, followed by an account of the development of national research facilities at the Lucas Heights Research Laboratories, with particular emphasis on nuclear techniques of analyses using neutron scattering instruments and particle accelerators. AINSE's program of Grants, fellowships and studentships are explained with many examples given of projects having significance in the context of Australia's national goals. Conference and training programs are also included. The achievements during these years demonstrate that AINSE has been an efficient and cost-effective model for collaboration between universities and a major national laboratory. In recent years, industry, government organisations and the tertiary education system have undergone major re-structuring and rationalization. A new operational structure for AINSE has evolved in response to these changes and is described

Mechanical Engineering Department technical review

Energy Technology Data Exchange (ETDEWEB)

Carr, R.B.; Abrahamson, L.; Denney, R.M.; Dubois, B.E (eds.)

1982-01-01

Technical achievements and publication abstracts related to research in the following Divisions of Lawrence Livermore Laboratory are reported in this biannual review: Nuclear Fuel Engineering; Nuclear Explosives Engineering; Weapons Engineering; Energy Systems Engineering; Engineering Sciences; Magnetic Fusion Engineering; and Material Fabrication. (LCL)

Development and integration of modern laboratories in aerospace education

Science.gov (United States)

Desautel, D.; Hunter, N.; Mourtos, N.; Pernicka, H.

1992-01-01

This paper describes the development and integration of a suite of laboratories in an aerospace engineering program. The program's approach to undergraduate education is described as the source for the development of the supporting laboratories. Nine laboratories supporting instruction were developed and installed. The nine laboratories include most major flight-vehicle disciplines. The purpose and major equipments/experiments of each laboratory are briefly described, as is the integration of the laboratory with coursework. The laboratory education provided by this program successfully achieves its purpose of producing competitive aerospace engineering graduates and advancing the level of undergraduate education.

Supplemental investigations in support of environmental assessments by the Idaho INEL Oversight Program at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

1992-01-01

This document reports on the status of supplemental investigations in support of environmental assessments by the Idaho INEL Oversight Program at the Idaho National Engineering Laboratory. Included is information on hydrology studies in wells open through large intervals, unsaturated zone contamination and transport processes, surface water-groundwater interactions, regional groundwater flow, and independent testing of air quality data

Seismic engineering for an expanded tritium facility at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Volkman, D.E.; Olive, W.B.; Endebrocid, E.E.; Khan, P.K.; Rebillet, W.R.

1997-10-01

An existing complex of three single story concrete and masonry shear wall buildings will be integrated into an expanded tritium facility for neutron tube target loading. Known as the NTTL Project, the expanded plant is a major element of the Department of Energy's tritium program at the Los Alamos National Laboratory. This paper describes seismic evaluation and upgrade modifications for the 1950's concrete shear wall building; drift analyses of two 1980's CMU [concrete masonry unit] shear wall buildings; design of a new CMU shear wall building linking existing structures and providing personnel change room services; and design of a new steel frame building housing HVAC and electrical power and communication equipment for the complex. All buildings are closely adjacent and drift analysis to establish separation to prevent pounding is a major seismic engineering concern for the project

Mixed waste treatment options for wastes generated at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Garcia, E.C.

1991-01-01

The Idaho National Engineering Laboratory has generated mixed wastes (MWs) during its daily operations. MWs contain both radioactive and hazardous components, as defined by the Department of Energy and the Environmental Protection Agency. Treatment and disposal of stored MWs, as well as future generated MWs, are required to meet all regulations specified by the regulating agencies. This report reviews proven and emerging technologies that can treat MWs. It also provides a method for selection of the appropriate technology for treatment of a particular waste stream. The report selects for further consideration various treatments that can be used to treat MWs that fall under Land Disposal Restrictions. The selection methodology was used to arrive at these treatments. 63 refs., 7 figs., 23 tabs

The Idaho National Engineering Laboratory site environmental report for calendar year 1989

International Nuclear Information System (INIS)

Hoff, D.L.; Mitchell, R.G.; Bowman, G.C.; Moore, R.

1990-06-01

To verify that exposures resulting from operations at the Department of Energy (DOE) nuclear facilities have remained very small, each site at which nuclear activities are underway operates an environmental surveillance program to monitor the air, water and any other pathway where radionuclides from operations might conceivably reach workers or members of the public. This report presents data collected in 1989 for the routine environmental surveillance program conducted by the Radiological and Environmental Sciences Laboratory (RESL) of DOE and the US Geological Survey (USGS) at the Idaho National Engineering Laboratory (INEL) site. The environmental surveillance program for the INEL and vicinity for 1989 included the collection and analysis of samples from potential exposure pathways. Three basic groups of samples were collected. Those collected within the INEL boundaries will be referred to as onsite samples. Samples collected outside, but near, the Site boundaries will be referred to as boundary samples or part of a group of offsite samples. Samples collected from locations considerably beyond the Site boundaries will be referred to as distant samples or part of the offsite group. With the exception of Craters of the Moon National Monument, the distant locations are sufficiently remote from the Site to ensure that detectable radioactivity is primarily due to natural background sources or sources other than INEL operations. 35 refs., 14 figs., 13 tabs

Emergence of a New Norovirus GII.4 Variant and Changes in the Historical Biennial Pattern of Norovirus Outbreak Activity in Alberta, Canada, from 2008 to 2013

Science.gov (United States)

Hasing, Maria E.; Preiksaitis, Jutta K.; Tellier, Raymond; Honish, Lance; Senthilselvan, Ambikaipakan; Pang, Xiaoli L.

2013-01-01

The public health impact of the emergence of new norovirus (NoV) strains is uncertain. A biennial pattern of alternating quiescent and epidemic levels of NoV outbreak activity associated with the emergence of new GII.4 variants was observed in Alberta, Canada, between July 2000 and June 2008. In this study, NoV genogroup I (GI) and GII strains isolated from 710 outbreak specimens in Alberta between July 2008 and January 2013 were characterized to update historical data. The seasonality and annual variation in NoV outbreak burden were analyzed over a 10-year period (July 2002 to June 2012). We found that GII.4-2006b had persisted as the predominant variant over three observation periods (July 2006 to June 2009) during which the biennial NoV outbreak pattern continued. The emergence of GII.4-2010 (winter 2009) was not associated with increased outbreak activity, and outbreak activity between July 2009 and June 2012 when GII.4-2010 predominated (67.5 to 97.7%) did not follow a biennial pattern. GII.4-2012 first emerged in Alberta in September 2011 and became predominant in observation period July 2012 to June 2013. NoV GI, relatively rare in past years, had a higher activity level (37.3%) as represented by GI.6 and GI.7 in the winter of 2012 to 2013. A higher proportion of GI outbreaks occurred in non-health care facility settings compared to GII. Our study suggests that factors other than new variants emergence contribute to the levels of NoV outbreak activity in Alberta. PMID:23637302

Proposals for ORNL [Oak Ridge National Laboratory] support to Tiber LLNL [Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Berry, L.A.; Rosenthal, M.W.; Saltmarsh, M.J.; Shannon, T.E.; Sheffield, J.

1987-01-01

This document describes the interests and capabilities of Oak Ridge National Laboratory in their proposals to support the Lawrence Livermore National Laboratory (LLNL) Engineering Test Reactor (ETR) project. Five individual proposals are cataloged separately. (FI)

Introducing "Green" and "Nongreen" Aspects of Noble Metal Nanoparticle Synthesis: An Inquiry-Based Laboratory Experiment for Chemistry and Engineering Students

Science.gov (United States)

Paluri, Sesha L. A.; Edwards, Michelle L.; Lam, Nhi H.; Williams, Elizabeth M.; Meyerhoefer, Allie; Pavel Sizemore, Ioana E.

2015-01-01

In recent years, nanoscience and nanotechnology have been drawing enormous attention due to the numerous applications of nanomaterials. In an attempt to nurture interest towards these areas in young minds and to develop the next generation of environmentally conscious scientists and engineers, this new laboratory module focuses on the green and…

Preliminary Waste Form Compliance Plan for the Idaho National Engineering and Environmental Laboratory High-Level Waste

Energy Technology Data Exchange (ETDEWEB)

B. A. Staples; T. P. O' Holleran

1999-05-01

The Department of Energy (DOE) has specific technical and documentation requirements for high-level waste (HLW) that is to be placed in a federal repository. This document describes in general terms the strategy to be used at the Idaho National Engineering and Environmental Laboratory (INEEL) to demonstrate that vitrified HLW, if produced at the INEEL, meets these requirements. Waste form, canister, quality assurance, and documentation specifications are discussed. Compliance strategy is given, followed by an overview of how this strategy would be implemented for each specification.

Preliminary Waste Form Compliance Plan for the Idaho National Engineering and Environmental Laboratory High-Level Waste

International Nuclear Information System (INIS)

Staples, B. A.; O'Holleran, T. P.

1999-01-01

The Department of Energy (DOE) has specific technical and documentation requirements for high-level waste (HLW) that is to be placed in a federal repository. This document describes in general terms the strategy to be used at the Idaho National Engineering and Environmental Laboratory (INEEL) to demonstrate that vitrified HLW, if produced at the INEEL, meets these requirements. Waste form, canister, quality assurance, and documentation specifications are discussed. Compliance strategy is given, followed by an overview of how this strategy would be implemented for each specification

Comparison of Responses on the 1994 Biennial Student Survey by the Consumer and Hospitality Services Division and Overall Students of the Milwaukee Area Technical College.

Science.gov (United States)

Advincula-Carpenter, Marietta M.

To gather curriculum planning information, the Research, Planning and Development Division of Milwaukee Area Technical College (MATC) conducts student surveys biennially. Responses of 579 MATC students enrolled in consumer and hospitality services division (CHSD) programs to the 1994 survey were compared with those of the 5,071 students…

Mathematics Education for Engineering Technology Students – A Bridge Too Far?

Directory of Open Access Journals (Sweden)

Noraishiyah Abdullah

2013-03-01

Full Text Available Trying to decide what is best suited for someone or something is an ever enduring task let alone trying to prepare students with the right engineering mind. So ‘how do you build an engineer?’ if that is the right word. What is the right ingredient? Mathematics has been said as the most important foundation in engineers’ life. Curriculum has been developed and reviewed over the years to meet this target. This work explores how much or lack of it has the curriculum prepares the future technologist to face the world of engineering technology as far as mathematics is concerned. Analysis of mathematics lectures, interviews of engineering technologist students and engineering technology subject lecturer is undertaken. Understand what each contributes help in understanding the picture that the current education is painting. Based on the theory of learning, APOS theory helps in explaining how students bridge their knowledge of mathematics when it comes to solving engineering technology problems. The question is, is it a bridge too far? 

MIT Lincoln Laboratory Facts 2015

Science.gov (United States)

2015-01-01

Positions filled by engineers and scientists at Lincoln Laboratory require problem-solving ability, analytical skills, and creativity ...balance, as well as offer- ing flexible work schedules, part-time employment, and telecommuting opportunities. Child Care The Lincoln Laboratory

Characterizing Instructional Practices in the Laboratory: The Laboratory Observation Protocol for Undergraduate STEM

Science.gov (United States)

Velasco, Jonathan B.; Knedeisen, Adam; Xue, Dihua; Vickrey, Trisha L.; Abebe, Marytza; Stains, Marilyne

2016-01-01

Chemistry laboratories play an essential role in the education of undergraduate Science, Technology, Engineering, and Mathematics (STEM) and non-STEM students. The extent of student learning in any educational environment depends largely on the effectiveness of the instructors. In chemistry laboratories at large universities, the instructors of…

Strategic Plan | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Johnson Controls | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Current Students | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Admissions - Undergraduate Students | College of Engineering & Applied

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Student Organizations | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Corporate Partners | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Travel Directions | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Strategic Planning | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Fast Facts | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Transfer Students | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Corporate Services | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Research Collaborations | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Study Abroad | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Undergraduate Curriculum | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Incoming Freshman | College of Engineering & Applied Science

Science.gov (United States)

Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

Multiyear Program Plan for the High Temperature Materials Laboratory; FINAL

International Nuclear Information System (INIS)

Arvid E. Pasto

2000-01-01

Recently, the U.S. Department of Energy's (DOE) Office of Heavy Vehicle Technologies (OHVT) prepared a Technology Roadmap describing the challenges facing development of higher fuel efficiency, less polluting sport utility vehicles, vans, and commercial trucks. Based on this roadmap, a multiyear program plan (MYPP) was also developed, in which approaches to solving the numerous challenges are enumerated. Additional planning has been performed by DOE and national laboratory staff, on approaches to solving the numerous challenges faced by heavy vehicle system improvements. Workshops and planning documents have been developed concerning advanced aerodynamics, frictional and other parasitic losses, and thermal management. Similarly, the Heavy Vehicle Propulsion Materials Program has developed its own multiyear program plan. The High Temperature Materials Laboratory, a major user facility sponsored by OHVT, has now developed its program plan, described herein. Information was gathered via participation in the development of OHVT's overall Technology Roadmap and MYPP, through personal contacts within the materials-user community, and from attendance at conferences and expositions. Major materials issues for the heavy vehicle industry currently center on trying to increase efficiency of (diesel) engines while at the same time reducing emissions (particularly NO(sub x) and particulates). These requirements dictate the use of increasingly stronger, higher-temperature capable and more corrosion-resistant materials of construction, as well as advanced catalysts, particulate traps, and other pollution-control devices. Exhaust gas recirculation (EGR) is a technique which will certainly be applied to diesel engines in the near future, and its use represents a formidable challenge, as will be described later. Energy-efficient, low cost materials processing methods and surface treatments to improve wear, fracture, and corrosion resistance are also required

Synthesis, Structural, Viscosimetric, And Rheological Study, of A New Trifunctional Phosphorus Epoxyde Prepolymer , Tri-Glycidyl Ether Tri-Mercaptoethanol Of Phosphore (TGETMEP

Directory of Open Access Journals (Sweden)

Atiqa Bekhta

2016-10-01

Full Text Available The aim of our work is to synthesize a new phosphorus tri-functional epoxy resin tri-glycidyl ether tri-mercaptoethanol of phosphorus (TGETMEP in two stages. In the first stage, we got the precursor molecule of the epoxy matrix tri-mercaptoethanol phosphate (METR. The second step led us to the synthesis of tri-functional resin TMEP condensation with epichlorohydrin. The standard TGETMEP resin was characterized by the Fourier infrared transformation (FTIR and nuclear magnetic resonance (NMR, on one hand. The viscosimetric analysis was investigated by the Hebbelod capillary viscometer and rheometer Rheomat 01, on the other hand. The cross-linked resins and tertiary formulated composites have been studied by the rheometer 01 which was observed by means of SEM.

Report of the research results with University of Tokyo, Nuclear Engineering Research Laboratory's Facilities in fiscal 1986

International Nuclear Information System (INIS)

1987-01-01

This book contains a large number of reports of studies made in 1986 through joint utilization of the nuclear reactor 'Yayoi' and electron beam type accelerator which are installed in the Nuclear engineering Research Laboratory, Faculty of Engineering, University of Tokyo. The reports presented deal with 'Behaviors of Neutrons in Fast Reactor Blanket Shield', 'Effect of Fast Neutron Radiation on Organic Materials', 'Production and Recovery of Tritium in Nuclear Fusion Reactor Blanket System', 'Bench Mark Experiment of Effect of Atmospheric Scattering of Neutron', 'Experimental Evaluation of Nuclear Heat Rate', 'Fast Neutron Shielding Experiment', 'Effect of Fast Neutron Radiation on Hot Water', 'Neutron Shielding Experiment', 'Biological and Medical Application of 'Yayoi' Neutron', 'Effect of Fission-Fusion Correlation Radiation on Semiconductors (Si, GaAs)', 'Application of Fast Neutron to Radiography Technology', 'Streaming in Offset Slit', 'Design and Evaluation of New Reactor', 'LET Effect on Organic Material', 'Handling, Separation and Recovery of Transuranium Elements', 'Reactor Operation Support System Using Knowledge Engineering Technique', 'Application of Shape Memory Alloys to Nuclear Reactor Devices', 'Numerical Simulation of Turbulent Hear Transfer', and many other studies. (Nogami, K.)

Laboratory quality assurance

International Nuclear Information System (INIS)

Delvin, W.L.

1977-01-01

The elements (principles) of quality assurance can be applied to the operation of the analytical chemistry laboratory to provide an effective tool for indicating the competence of the laboratory and for helping to upgrade competence if necessary. When used, those elements establish the planned and systematic actions necessary to provide adequate confidence in each analytical result reported by the laboratory (the definition of laboratory quality assurance). The elements, as used at the Hanford Engineering Development Laboratory (HEDL), are discussed and they are qualification of analysts, written methods, sample receiving and storage, quality control, audit, and documentation. To establish a laboratory quality assurance program, a laboratory QA program plan is prepared to specify how the elements are to be implemented into laboratory operation. Benefits that can be obtained from using laboratory quality assurance are given. Experience at HEDL has shown that laboratory quality assurance is not a burden, but it is a useful and valuable tool for the analytical chemistry laboratory

Adverse effect of diesel engine produced particulate matter on various stone types and concrete: a laboratory exposure experiment

Science.gov (United States)

Farkas, Orsolya; Szabados, György; Antal, Ákos; Török, Ákos

2015-04-01

The effect of particulate matter on construction materials have been studied under laboratory conditions. For testing the adverse effects of diesel soot and particulate matter on stone and concrete a small scale laboratory exposure chamber was constructed. Blocks of 9 different stone types and concrete was placed in the chamber and an exhaust pipe of diesel engine was diverted into the system. Tested stones included: porous limestone, cemented non-porous limestone, travertine, marble, rhyolite tuff, andesite and granite. The engine was operated for 10 hours and the produced particulate matter was diverted directly to the surface of the material specimens of 3 cm in diameter each. Working parameters of the engine were controlled; the composition of the exhaust gas, smoke value and temperature were continuously measured during the test. Test specimens were documented and analysed prior to exposure and after the exposure test. Parameters such colorimetric values, weight, surface properties, mineralogical compositions of the test specimens were recorded. The working temperature was in the order of 300°C-320°C. The gas concentration was in ppm as follows: 157 CO; 5.98 CO2, 34.3 THC; 463 NOx; 408 NO; 12.88 O2. Our tests have demonstrated that significant amount of particulate matter was deposited on construction materials even at a short period of time; however the exposure was very intense. It also indicates that that the interaction of particulate matter and aerosol compounds with construction materials in urban areas causes rapid decay and has an adverse effect not only on human health but also on built structures.

Reactor laboratory course for students majoring in nuclear engineering with the Kyoto University Critical Assembly (KUCA)

International Nuclear Information System (INIS)

Nishihara, H.; Shiroya, S.; Kanda, K.

1996-01-01

With the use of the Kyoto University Critical Assembly (KUCA), a joint reactor laboratory course of graduate level is offered every summer since 1975 by nine associated Japanese universities (Hokkaido University, Tohoku University, Tokyo Institute of Technology, Musashi Institute of Technology, Tokai University, Nagoya University, Osaka University, Kobe University of Mercantile Marine and Kyushu University) in addition to a reactor laboratory course of undergraduate level for Kyoto University. These courses are opened for three weeks (two weeks for the joint course and one week for the undergraduate course) to students majoring in nuclear engineering and a total of 1,360 students have taken the course in the last 21 years. The joint course has been institutionalized with the background that it is extremely difficult for a single university in Japan to have her own research or training reactor. By their effort, the united faculty team of the joint course have succeeded in giving an effective, unique one-week course, taking advantage of their collaboration. Last year, an enquete (questionnaire survey) was conducted to survey the needs for the educational experiments of graduate level and precious data have been obtained for promoting reactor laboratory courses. (author)

Department of Energy Programmatic Spent Nuclear Fuel Management and Idaho National Engineering Laboratory Environmental Restoration and Waste Management Programs Draft Environmental Impact Statement

International Nuclear Information System (INIS)

1994-06-01

This document analyzes at a programmatic level the potential environmental consequences over the next 40 years of alternatives related to the transportation, receipt, processing, and storage of spent nuclear fuel under the responsibility of the US Department of Energy. It also analyzes the site-specific consequences of the Idaho National Engineering Laboratory sitewide actions anticipated over the next 10 years for waste and spent nuclear fuel management and environmental restoration. For programmatic spent nuclear fuel management this document analyzes alternatives of no action, decentralization, regionalization, centralization and the use of the plans that existed in 1992/1993 for the management of these materials. For the Idaho National Engineering Laboratory, this document analyzes alternatives of no action, ten-year plan, minimum and maximum and maximum treatment, storage, and disposal of US Department of Energy wastes

Department of Energy Programmatic Spent Nuclear Fuel Management and Idaho National Engineering Laboratory Environmental Restoration and Waste Management Programs Draft Environmental Impact Statement

International Nuclear Information System (INIS)

1994-06-01

This document analyzes at a pregrammatic level the potential environmental consequences over the next 40 years of alternatives related to the transportation, receipt, processing, and storage of spent nuclear fuel under the responsibility of the US Department of Energy. It also analyzes the site-specific consequences of the Idaho National Engineering Laboratory sitewide actions anticipated over the next 10 years for waste and spent nuclear fuel management and environmental restoration. For pregrammatic spent nuclear fuel management, this document analyzes alternatives of no action, decentralization, regionalization, centralization and the use of the plans that existed in 1992/1993 for the management of these materials. For the Idaho National Engineering Laboratory, this document analyzes alternatives of no action, ten-year plan, minimum and maximum treatment, storage, and disposal of US Department of Energy wastes

Department of Energy Programmatic Spent Nuclear Fuel Management and Idaho National Engineering Laboratory Environmental Restoration and Waste Management Programs draft environmental impact statement

International Nuclear Information System (INIS)

1994-06-01

This document analyzes at a programmatic level the potential environmental consequences over the next 40 years of alternatives related to the transportation, receipt, processing, and storage of spent nuclear fuel under the responsibility of the US Department of Energy. It also analyzes the site-specific consequences of the Idaho National Engineering Laboratory sitewide actions anticipated over the next 10 years for waste and spent nuclear fuel management and environmental restoration. For programmatic spent nuclear fuel management, this document analyzes alternatives of no action, decentralization, regionalization, centralization and the use of the plans that existed in 1992/1993 for the management of these materials. For the Idaho National Engineering Laboratory, this document analyzes alternatives of no action, ten-year plan, minimum and maximum treatment, storage, and disposal of US Department of Energy wastes

Simula Research Laboratory

CERN Document Server

Tveito, Aslak

2010-01-01

The Simula Research Laboratory, located just outside Oslo in Norway, is rightly famed as a highly successful research facility, despite being, at only eight years old, a very young institution. This fascinating book tells the history of Simula, detailing the culture and values that have been the guiding principles of the laboratory throughout its existence. Dedicated to tackling scientific challenges of genuine social importance, the laboratory undertakes important research with long-term implications in networks, computing and software engineering, including specialist work in biomedical comp

1996 LMITCO environmental monitoring program report for the Idaho National Engineering and Environmental Laboratory

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

This report describes the calendar year 1996 environmental surveillance and compliance monitoring activities of the Lockheed Martin Idaho Technologies Company Environmental Monitoring Program performed at the Idaho National Engineering and Environmental Laboratory (INEEL). Results of sampling performed by the Radiological Environmental Surveillance, Site Environmental Surveillance, Drinking Water, Effluent Monitoring, Storm Water Monitoring, Groundwater Monitoring, and Special Request Monitoring Programs are included in this report. The primary purposes of the surveillance and monitoring activities are to evaluate environmental conditions, to provide and interpret data, to verify compliance with applicable regulations or standards, and to ensure protection of human health and the environment. This report compares 1996 data with program-specific regulatory guidelines and past data to evaluate trends.

1996 LMITCO environmental monitoring program report for the Idaho National Engineering and Environmental Laboratory

International Nuclear Information System (INIS)

1997-09-01

This report describes the calendar year 1996 environmental surveillance and compliance monitoring activities of the Lockheed Martin Idaho Technologies Company Environmental Monitoring Program performed at the Idaho National Engineering and Environmental Laboratory (INEEL). Results of sampling performed by the Radiological Environmental Surveillance, Site Environmental Surveillance, Drinking Water, Effluent Monitoring, Storm Water Monitoring, Groundwater Monitoring, and Special Request Monitoring Programs are included in this report. The primary purposes of the surveillance and monitoring activities are to evaluate environmental conditions, to provide and interpret data, to verify compliance with applicable regulations or standards, and to ensure protection of human health and the environment. This report compares 1996 data with program-specific regulatory guidelines and past data to evaluate trends

Studies on engineering technologies in the Mizunami Underground Research Laboratory. FY 2007 (Contract research)

International Nuclear Information System (INIS)

Noda, Masaru; Suyama, Yasuhiro; Nobuto, Jun; Ijiri, Yuji; Mikake, Shinichiro; Matsui, Hiroya

2009-07-01

The Mizunami Underground Research Laboratory (MIU) of the Japan Atomic Energy Agency is a major site for geoscientific research to advance the scientific and technological basis for geological disposal of high-level radioactive waste in crystalline rock. Studies on relevant engineering technologies in the MIU consist of a) research on design and construction technology for very deep underground applications, and b) research on engineering technology as a basis of geological disposal. In the Second Phase of the MIU project (the construction phase), engineering studies have focused on research into design and construction technologies for deep underground. The main subjects in the study of very deep underground structures consist of the following: 'Demonstration of the design methodology', 'Demonstration of existing and supplementary excavation methods', 'Demonstration of countermeasures during excavation' and 'Demonstration of safe construction'. In the FY 2007 studies, identification and evaluation of the subjects for study of engineering technologies in the construction phase were carried out to optimize future research work. Specific studies included: validation of the existing design methodology based on data obtained during construction; validation of existing and supplementary rock excavation methods for very deep shafts; estimation of rock stability under high differential water pressures, methodology on long-term maintenance of underground excavations and risk management systems for construction of underground structures have been performed. Based on these studies, future research focused on the four subject areas, which are 'Demonstration of the design methodology', 'Demonstration of existing and supplementary excavation methods', 'Demonstration of countermeasures during excavation' and 'Demonstration of safe construction', has been identified. The design methodology in the first phase of the MIU Project (surface-based investigation phase) was verified to

Mechanical Engineering Senior Design Project Final Presentations | College

Science.gov (United States)

Engineering Research Computational Mechanics Laboratory Environmental Engineering Laboratory Geotechnical of Engineering & Applied Science A B C D E F G H I J K L M N O P Q R S T U V W X Y Z D2L Programs Concentration in Biomedical Engineering Concentration on Ergonomics M.S. Program in Computer

Multiyear Program Plan for the High Temperature Materials Laboratory

Energy Technology Data Exchange (ETDEWEB)

Arvid E. Pasto

2000-03-17

Recently, the U.S. Department of Energy's (DOE) Office of Heavy Vehicle Technologies (OHVT) prepared a Technology Roadmap describing the challenges facing development of higher fuel efficiency, less polluting sport utility vehicles, vans, and commercial trucks. Based on this roadmap, a multiyear program plan (MYPP) was also developed, in which approaches to solving the numerous challenges are enumerated. Additional planning has been performed by DOE and national laboratory staff, on approaches to solving the numerous challenges faced by heavy vehicle system improvements. Workshops and planning documents have been developed concerning advanced aerodynamics, frictional and other parasitic losses, and thermal management. Similarly, the Heavy Vehicle Propulsion Materials Program has developed its own multiyear program plan. The High Temperature Materials Laboratory, a major user facility sponsored by OHVT, has now developed its program plan, described herein. Information was gathered via participation in the development of OHVT's overall Technology Roadmap and MYPP, through personal contacts within the materials-user community, and from attendance at conferences and expositions. Major materials issues for the heavy vehicle industry currently center on trying to increase efficiency of (diesel) engines while at the same time reducing emissions (particularly NO{sub x} and particulates). These requirements dictate the use of increasingly stronger, higher-temperature capable and more corrosion-resistant materials of construction, as well as advanced catalysts, particulate traps, and other pollution-control devices. Exhaust gas recirculation (EGR) is a technique which will certainly be applied to diesel engines in the near future, and its use represents a formidable challenge, as will be described later. Energy-efficient, low cost materials processing methods and surface treatments to improve wear, fracture, and corrosion resistance are also required.

Kingsbury Laboratories

International Nuclear Information System (INIS)

Hughes, S.B.

1986-01-01

The paper concerns the work of the Kingsbury Laboratories of Fairey Engineering Company, for the nuclear industry. The services provided include: monitoring of nuclear graphite machining, specialist welding, non-destructive testing, and metallurgy testing; and all are briefly described. (U.K.)

Power Systems Integration Laboratory | Energy Systems Integration Facility

Science.gov (United States)

| NREL Power Systems Integration Laboratory Power Systems Integration Laboratory Research in the Energy System Integration Facility's Power Systems Integration Laboratory focuses on the microgrid applications. Photo of engineers testing an inverter in the Power Systems Integration Laboratory

Toxics Release Inventory (TRI)

Data.gov (United States)

U.S. Environmental Protection Agency — The Toxics Release Inventory (TRI) is a dataset compiled by the U.S. Environmental Protection Agency (EPA). It contains information on the release and waste...

MEMS Sensors and Actuators Laboratory (MSAL)

Data.gov (United States)

Federal Laboratory Consortium — The MEMS Sensors and Actuators Laboratory (MSAL) in the A.J. Clark School of Engineering at the University of Maryland (UMD) was established in January 2000. Our lab...

Laboratory Characterization of Gray Masonry Concrete

National Research Council Canada - National Science Library

Williams, Erin M; Akers, Stephen A; Reed, Paul A

2007-01-01

Personnel of the Geotechnical and Structures Laboratory, U.S. Army Engineer Research and Development Center, conducted a laboratory investigation to characterize the strength and constitutive property behavior of a gray masonry concrete...

Thickness of surficial sediment at and near the Idaho National Engineering Laboratory, Idaho

International Nuclear Information System (INIS)

Anderson, S.R.; Liszewski, M.J.; Ackerman, D.J.

1996-06-01

Thickness of surficial sediment was determined from natural-gamma logs in 333 wells at and near the Idaho National Engineering Laboratory in eastern Idaho to provide reconnaissance data for future site-characterization studies. Surficial sediment, which is defined as the unconsolidated clay, silt, sand, and gravel that overlie the uppermost basalt flow at each well, ranges in thickness from 0 feet in seven wells drilled through basalt outcrops east of the Idaho Chemical Processing Plant to 313 feet in well Site 14 southeast of the Big Lost River sinks. Surficial sediment includes alluvial, lacustrine, eolian, and colluvial deposits that generally accumulated during the past 200 thousand years. Additional thickness data, not included in this report, are available from numerous auger holes and foundation borings at and near most facilities

Use of search engine optimization factors for Google page rank prediction

OpenAIRE

Tvrdi, Barbara

2012-01-01

Over the years, search engines have become an important tool for finding information. It is known that users select the link on the first page of search results in 62% of the cases. Search engine optimization techniques enable website improvement and therefore a better ranking in search engines. The exact specification of the factors that affect website ranking is not disclosed by search engine owners. In this thesis we tried to choose some most frequently mentioned search engine optimizatio...

Aircraft Wiring Support Equipment Integration Laboratory (AWSEIL)

Data.gov (United States)

Federal Laboratory Consortium — Purpose:The Aircraft Wiring Support Equipment Integration Laboratory (AWSEIL) provides a variety of research, design engineering and prototype fabrication services...

Remedial design and remedial action guidance for the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

1993-10-01

The US Department of Energy, Idaho Operations Office (DOE-ID), the US Environmental Protection Agency, Region X (EPA), and the Idaho Department of Health and Welfare (IDHW) have developed this guidance on the remedial design and remedial action (RD/RA) process. This guidance is applicable to activities conducted under the Idaho National Engineering Laboratory (INEL) Federal Facility Agreement and Consent Order (FFA/CO) and Action Plan. The INEL FFA/CO and Action Plan provides the framework for performing environmental restoration according to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). The guidance is intended for use by the DOE-ID, the EPA, and the IDHW Waste Area Group (WAG) managers and others involved in the planning and implementation of CERCLA environmental restoration activities. The scope of the guidance includes the RD/RA strategy for INEL environmental restoration projects and the approach to development and review of RD/RA documentation. Chapter 2 discusses the general process, roles and responsibilities, and other elements that define the RD/RA strategy. Chapters 3 through 7 describe the RD/RA documents identified in the FFA/CO and Action Plan. Chapter 8 provides examples of how this guidance can be applied to restoration projects. Appendices are included that provide excerpts from the FFA/CO pertinent to RD/RA (Appendix A), a applicable US Department of Energy (DOE) orders (Appendix B), and an EPA Engineering ''Data Gaps in Remedial Design'' (Appendix C)

Waste Isolation Pilot Plant Biennial Environmental Compliance Report

Energy Technology Data Exchange (ETDEWEB)

Washinton TRU Solutions LLC

2002-09-30

This Biennial Environmental Compliance Report (BECR) documents environmental regulatory compliance at the Waste Isolation Pilot Plant (WIPP), a facility designed for the safe disposal of transuranic (TRU) radioactive waste, for the reporting period of April 1, 2000, to March 31, 2002. As required by the WIPP Land Withdrawal Act (LWA)(Public Law [Pub. L.] 102-579, as amended by Pub. L. 104-201), the BECR documents U.S. Department of Energy (DOE) Carlsbad Field Office's (CBFO) compliance with applicable environmental protection laws and regulations implemented by agencies of the federal government and the state of New Mexico. In the prior BECR, the CBFO and the management and operating contractor (MOC)committed to discuss resolution of a Letter of Violation that had been issued by the New Mexico Environment Department (NMED) in August 1999, which was during the previous BECR reporting period. This Letter of Violation alleged noncompliance with hazardous waste aisle spacing, labeling, a nd tank requirements. At the time of publication of the prior BECR, resolution of the Letter of Violation was pending. On July 7, 2000, the NMED issued a letter noting that the aisle spacing and labeling concerns had been adequately addressed and that they were rescinding the violation alleging that the Exhaust Shaft Catch Basin failed to comply with the requirements for a hazardous waste tank. During the current reporting period, WIPP received a Notice of Violation and a compliance order alleging the violation of the New Mexico Hazardous Waste Regulations and the WIPP Hazardous Waste Facility Permit (HWFP).

Waste Isolation Pilot Plant Biennial Environmental Compliance Report

International Nuclear Information System (INIS)

Washinton TRU Solutions LLC

2002-01-01

This Biennial Environmental Compliance Report (BECR) documents environmental regulatory compliance at the Waste Isolation Pilot Plant (WIPP), a facility designed for the safe disposal of transuranic (TRU) radioactive waste, for the reporting period of April 1, 2000, to March 31, 2002. As required by the WIPP Land Withdrawal Act (LWA)(Public Law [Pub. L.] 102-579, as amended by Pub. L. 104-201), the BECR documents U.S. Department of Energy (DOE) Carlsbad Field Office's (CBFO) compliance with applicable environmental protection laws and regulations implemented by agencies of the federal government and the state of New Mexico. In the prior BECR, the CBFO and the management and operating contractor (MOC)committed to discuss resolution of a Letter of Violation that had been issued by the New Mexico Environment Department (NMED) in August 1999, which was during the previous BECR reporting period. This Letter of Violation alleged noncompliance with hazardous waste aisle spacing, labeling, a nd tank requirements. At the time of publication of the prior BECR, resolution of the Letter of Violation was pending. On July 7, 2000, the NMED issued a letter noting that the aisle spacing and labeling concerns had been adequately addressed and that they were rescinding the violation alleging that the Exhaust Shaft Catch Basin failed to comply with the requirements for a hazardous waste tank. During the current reporting period, WIPP received a Notice of Violation and a compliance order alleging the violation of the New Mexico Hazardous Waste Regulations and the WIPP Hazardous Waste Facility Permit (HWFP)

Using predictive maintenance methods at Hanford Engineering Development Laboratory (HEDL) to increase equipment availability and reduce overall managed costs

International Nuclear Information System (INIS)

Stanton, G.A.; Grygiel, M.L.

1986-08-01

This paper describes the predictive maintenance program that is presently in place at Hanford Engineering Development Laboratory using vibration analysis and oil sampling techniques. A pilot program at the Fast Flux Test Facility (FFTF) has been established using reliability-based maintenance concepts such as trend and failure analysis techniques. The first system being analyzed at FFTF will be the electrical distribution system. 2 figs

Engine Test Facility (ETF)

Data.gov (United States)

Federal Laboratory Consortium — The Air Force Arnold Engineering Development Center's Engine Test Facility (ETF) test cells are used for development and evaluation testing of propulsion systems for...

Ice Engineering Research Area

Data.gov (United States)

Federal Laboratory Consortium — Refrigerated Physical Modeling of Waterways in a Controlled EnvironmentThe Research Area in the Ice Engineering Facility at the Cold Regions Research and Engineering...

Waste minimization value engineering workshop for the Los Alamos National Laboratory Omega West Reactor Decommissioning Project

International Nuclear Information System (INIS)

Hartnett, S.; Seguin, N.; Burns, M.

1995-01-01

The Los Alamos National Laboratory Pollution Prevention Program Office sponsored a Value Engineering (VE) Workshop to evaluate recycling options and other pollution prevention and waste minimization (PP/WMin) practices to incorporate into the decommissioning of the Omega West Reactor (OWR) at the laboratory. The VE process is an organized, systematic approach for evaluating a process or design to identify cost saving opportunities, or in this application, waste reduction opportunities. This VE Workshop was a facilitated process that included a team of specialists in the areas of decontamination, decommissioning, PP/WMin, cost estimating, construction, waste management, recycling, Department of Energy representatives, and others. The uniqueness of this VE Workshop was that it used an interdisciplinary approach to focus on PP/WMin practices that could be included in the OWR Decommissioning Project Plans and specifications to provide waste reduction. This report discusses the VE workshop objectives, summarizes the OWR decommissioning project, and describes the VE workshop activities, results, and lessons learned

Waste minimization value engineering workshop for the Los Alamos National Laboratory Omega West Reactor Decommissioning Project

Energy Technology Data Exchange (ETDEWEB)

Hartnett, S.; Seguin, N. [Benchmark Environmental Corp., Albuquerque, NM (United States); Burns, M. [Los Alamos National Lab., NM (United States)

1995-12-31

The Los Alamos National Laboratory Pollution Prevention Program Office sponsored a Value Engineering (VE) Workshop to evaluate recycling options and other pollution prevention and waste minimization (PP/WMin) practices to incorporate into the decommissioning of the Omega West Reactor (OWR) at the laboratory. The VE process is an organized, systematic approach for evaluating a process or design to identify cost saving opportunities, or in this application, waste reduction opportunities. This VE Workshop was a facilitated process that included a team of specialists in the areas of decontamination, decommissioning, PP/WMin, cost estimating, construction, waste management, recycling, Department of Energy representatives, and others. The uniqueness of this VE Workshop was that it used an interdisciplinary approach to focus on PP/WMin practices that could be included in the OWR Decommissioning Project Plans and specifications to provide waste reduction. This report discusses the VE workshop objectives, summarizes the OWR decommissioning project, and describes the VE workshop activities, results, and lessons learned.

Fleet Aviation Maintenance Organic Support (FAMOS) Laboratory

Data.gov (United States)

Federal Laboratory Consortium — Purpose:The Fleet Aviation Maintenance Organic Support (FAMOS) Laboratory at the Naval Air Warfare Center Aircraft Division, Lakehurst, NJ provides rapid engineering...

The Game of Tri

Science.gov (United States)

Haggard, Gary; Schonberger, Ann Koch

1977-01-01

The paper-and-pencil game "Tri" is described. The authors argue that students gain logical skills by playing the game, and that the game lends itself to the introduction of diverse mathematical ideas. (SD)

Computer Labs | College of Engineering & Applied Science

Science.gov (United States)

Engineering Concentration on Ergonomics M.S. Program in Computer Science Interdisciplinary Concentration on Structural Engineering Laboratory Water Resources Laboratory Computer Science Department Computer Science Academic Programs Computer Science Undergraduate Programs Computer Science Major Computer Science Tracks

Computer Resources | College of Engineering & Applied Science

Science.gov (United States)