Photoreduction of non-noble metal Bi on the surface of Bi{sub 2}WO{sub 6} for enhanced visible light photocatalysis

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xiaojing [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, No. 8, Xindu Road, Xindu District, Chengdu 610500 (China); The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, No. 8, Xindu Road, Xindu District, Chengdu 610500 (China); Yu, Shan; Liu, Yang; Zhang, Qian [The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, No. 8, Xindu Road, Xindu District, Chengdu 610500 (China); Zhou, Ying, E-mail: yzhou@swpu.edu.cn [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, No. 8, Xindu Road, Xindu District, Chengdu 610500 (China); The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, No. 8, Xindu Road, Xindu District, Chengdu 610500 (China)

2017-02-28

Highlights: • Bi{sub 2}WO{sub 6}-Bi composite was synthesized by in situ photoreduction of Bi{sub 2}WO{sub 6}. • Bi{sub 2}WO{sub 6}-Bi exhibits improved photocatalytic efficiency towards degradation of Rhodamine B. • The generation of elemental Bi in Bi{sub 2}WO{sub 6}-Bi induces vacancy and structure distortion of Bi{sub 2}WO{sub 6}. • The surface oxygen adsorption mode changes from hydroxyl group on Bi{sub 2}WO{sub 6} to molecular oxygen on Bi{sub 2}WO{sub 6}-Bi. - Abstract: In this report, Bi{sub 2}WO{sub 6}-Bi composite was prepared through an in situ photoreduction method and was characterized systematically by X-Ray diffraction, transmission electron microscopy, X-Ray photoelectron spectroscopy and UV-vis diffuse reflectance spectroscopy. The as-prepared Bi{sub 2}WO{sub 6}-Bi maintains the same crystal structure with the pristine Bi{sub 2}WO{sub 6} regardless of some surface defects. Nevertheless, these surface defects result in the change of surface oxygen adsorption mode from hydroxyl to molecular oxygen on Bi{sub 2}WO{sub 6}. Photocatalytic activity over Bi{sub 2}WO{sub 6}-Bi is 2.4 times higher than that of Bi{sub 2}WO{sub 6} towards the degradation of organic dye Rhodamine B (RhB) under visible light irradiation (λ > 420 nm). A deep study shows that cleavage of benzene ring is the main pathway for RhB degradation over Bi{sub 2}WO{sub 6}, but both the benzene cleavage and de-ethylation pathway coexist for RhB decomposition in the presence of Bi{sub 2}WO{sub 6}-Bi as the photocatalyst. Photoelectrochemical study including transient photocurrent tests and electrochemical impedance spectroscopy measurements shows that Bi{sub 2}WO{sub 6}-Bi could facilitate the charge transfer process compared to Bi{sub 2}WO{sub 6}. These data above has indicated a new insight into the promotion mechanism based on Bi related heterostructures.

High photocatalytic performance of BiOI/Bi{sub 2}WO{sub 6} toward toluene and Reactive Brilliant Red

Energy Technology Data Exchange (ETDEWEB)

Li Huiquan [School of Chemistry and Chemical Engineering, Fuyang Normal College, Fuyang 236041 (China); Key Laboratory of Mesoscopic Chemistry of MOE, Jiangsu Provincial Key Laboratory of Nanotechnology, School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210093 (China); Cui Yumin, E-mail: cuiyumin0908@163.com [School of Chemistry and Chemical Engineering, Fuyang Normal College, Fuyang 236041 (China); Hong Wenshan [School of Chemistry and Chemical Engineering, Fuyang Normal College, Fuyang 236041 (China)

2013-01-01

Graphical abstract: When BiOI/Bi{sub 2}WO{sub 6} catalyst was exposed to UV or visible light, the electrons in the valence band of Bi{sub 2}WO{sub 6} would be excited into the conduction band and then injected into the more positive conduction band of BiOI. Therefore, the photoelectrons were generated from Bi{sub 2}WO{sub 6} and transferred across the interface between BiOI and Bi{sub 2}WO{sub 6} to the surface of BiOI, leaving the photogenerated holes in the valence band of Bi{sub 2}WO{sub 6}. In this way, the photoinduced electron-hole pairs were effectively separated. Highlights: Black-Right-Pointing-Pointer BiOI sensitized Bi{sub 2}WO{sub 6} catalysts were successfully prepared by a facile method. Black-Right-Pointing-Pointer The 13.2% BiOI/Bi{sub 2}WO{sub 6} catalyst exhibits higher photoactivities than P25. Black-Right-Pointing-Pointer A possible transfer process of photogenerated carriers was proposed. - Abstract: BiOI sensitized nano-Bi{sub 2}WO{sub 6} photocatalysts with different BiOI contents were successfully synthesized by a facile deposition method at room temperature, and characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) high-resolution transmission electron microscopy (HR-TEM), photoluminescence (PL) spectra, UV-vis diffuse reflection spectroscopy (UV-vis DRS) and Brunauer-Emmett-Teller (BET) surface area measurements. The photocatalytic activity of BiOI/Bi{sub 2}WO{sub 6} was evaluated by the photo-degradation of Reactive Brilliant Red (X-3B) in suspended solution and toluene in gas phase. It has been shown that the BiOI/Bi{sub 2}WO{sub 6} catalysts exhibit a coexistence of both tetragonal BiOI and orthorhombic Bi{sub 2}WO{sub 6} phases. With increasing BiOI content, the absorption intensity of BiOI/Bi{sub 2}WO{sub 6} catalysts increases in the 380-600 nm region and the absorption edge shifts significantly to longer wavelengths as compared to pure Bi{sub 2}WO{sub 6}. The 13.2% BiOI/Bi{sub 2}WO{sub 6} catalyst exhibits

Non-noble metal Bi deposition by utilizing Bi2WO6 as the self-sacrificing template for enhancing visible light photocatalytic activity

Science.gov (United States)

Yu, Shixin; Zhang, Yihe; Li, Min; Du, Xin; Huang, Hongwei

2017-01-01

Bi metal deposited on Bi2WO6 composite photocatalysts have been successfully synthesized via a simple in-situ reduction method at room temperature with using Bi2WO6 as self-sacrificing template and NaBH4 as reducing agent. The reduction extent can be easily modulated by controlling the concentration of NaBH4 solution. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared (FTIR) spectra, N2 adsorption-desorption isotherms, scanning electron microscopy (SEM), transmission electron microscopy (TEM), high resolution TEM (HRTEM), diffuse reflection spectroscopy (DRS) and photoelectrochemical measurements were carried out to analyze the phase, morphology, optical property and photoelectrochemical property of the as-prepared samples. The photocatalytic activity is surveyed by degradation of phenol under visible light (λ > 420 nm), which showed that the BWO-0.2 photocatalyst exhibited the highest efficiency, which was over 3 times as high as pure Bi2WO6. The enhanced photocatalytic activity should be attributed to strengthened photoabsorption and charge separation efficiency derived from the surface plasmon resonance (SPR) of Bi metal.

PREPARATION AND VISIBLE LIGHT RESPONSIVE PHOTOCATALYTIC ACTIVITY OF Fe3O4/Ni-Al-Ce LDH/Bi2WO6 COMPOSITES

Directory of Open Access Journals (Sweden)

Jiaqi Hao

Full Text Available Novel Fe3O4/Ni-Al-Ce LDH/Bi2WO6 composites were prepared through a hydrothermal method and co-precipitation method. The morphologies and structures of the photocatalysts were characterized by XRD, Raman, TEM, UV-vis-DRS, BET surface area and VSM techniques. The photocatalytic performances of the photocatalysts were investigated by the decolorization of methyl orange (MO under visible-light irradiation. The results showed that the Fe3O4/Ni-Al-Ce LDH/Bi2WO6 composites exhibited greater photocatalytic activities compared to pure Bi2WO6 and the Ni-Al-Ce LDH; the decolorization rate of MO was 87% within 60 min under visible-light irradiation. The decolorization efficiency of the composite material remained at 71% after 4 recycling runs, showing improved stability. Furthermore, the experimental results also showed that the photocatalytic reactions for the composites followed first-order reaction kinetics. Therefore, the Fe3O4/Ni-Al-Ce LDH/Bi2WO6 composites were photocatalysts with high efficiencies and stabilities for a photocatalytic reaction of an organic pollutant, and this study provides a new, effective method for the development of wastewater treatment.

Inductive effect of poly(vinyl pyrrolidone) on morphology and photocatalytic performance of Bi{sub 2}WO{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Zhang, Qiang; Chen, Jinxing; Xie, Yunyun; Wang, Mozhen; Ge, Xuewu, E-mail: xwge@ustc.edu.cn

2016-04-15

Graphical abstract: - Highlights: • PVP molecular chains will induce the assembly of the primary Bi{sub 2}WO{sub 6} nanosheets. • The assembly of primary Bi{sub 2}WO{sub 6} nanosheets forms various 3D topological structure. • Sheet-like, flower-like, red-blood-cell-like and square-pillar-like Bi{sub 2}WO{sub 6} were formed. • Bi{sub 2}WO{sub 6} formed at low concentration or molecular weight of PVP has better activity. - Abstract: Bi{sub 2}WO{sub 6} has great potential applications in the field of photocatalyst due to its excellent visible-light photocatalytic performance. This work studied the detailed morphological evolution of Bi{sub 2}WO{sub 6} particles synthesized in a simple hydrothermal system induced by the stabilizer poly(vinyl pyrrolidone) (PVP). The XRD and HRTEM results show PVP would not change the crystal structure of Bi{sub 2}WO{sub 6}, but the distribution of PVP on the initially formed Bi{sub 2}WO{sub 6} nanosheets will induce the crystal growth, resulting in a distinct morphology evolution of Bi{sub 2}WO{sub 6} with the increase of the concentration of PVP. At the same time, with the increase of the molecular weight of PVP, the morphology of Bi{sub 2}WO{sub 6} varied from simple sheet-like (S-BWO) to some complicated morphology, such as flower-like (F-BWO), red blood cell-like (B-BWO), and square-pillar-like (SP-BWO). The photocatalytic performances of Bi{sub 2}WO{sub 6} with various morphologies on the decomposition of RhB under visible light irradiation reveal that S-BWO has the best photocatalytic performance, while SP-BWO has the worst. This work not only gives the explanation of the inductive effect of PVP molecular chains on the morphological formation of Bi{sub 2}WO{sub 6} particles, but also provides the controllable way to the preparation of Bi{sub 2}WO{sub 6} with various morphologies taking advantage of the stabilizer PVP.

Enhanced photocatalytic activity of cadmium-doped Bi{sub 2}WO{sub 6} nanoparticles under simulated solar light

Energy Technology Data Exchange (ETDEWEB)

Song, Xu Chun, E-mail: songxuchunfj@163.com; Li, Wen Ting [Fujian Normal University, Department of Chemistry (China); Huang, Wan Zhen; Zhou, Huan [Zhejiang University of Technology, Research Center of Analysis and Measurement (China); Yin, Hao Yong [Hangzhou Dianzi University, Institute of Environmental Science and Engineering (China); Zheng, Yi Fan [Zhejiang University of Technology, Research Center of Analysis and Measurement (China)

2015-03-15

Novel cadmium-doped Bi{sub 2}WO{sub 6} nanoparticles with different Cd contents have been synthesized by a one-step route using ethylene glycol and water as solvents at 180 °C for 12 h. The as-synthesized samples were characterized in detailed by SEM, XRD, EDS, HRTEM, UV–Vis DRS, BET techniques, and so on. The results shown that with the increase of the Cd{sup 2+} addition, the crystal structure, lattice space, and absorption edge were not significantly changed and the calculated band gap value was 2.58 eV. However, the flower-like Bi{sub 2}WO{sub 6} sphere was gradually destroyed. Simultaneously, the surface area and photocurrent responses of the catalysts were greatly increased. Photocatalytic activity of the Cd-doped Bi{sub 2}WO{sub 6} samples was determined by monitoring the change of RhB concentration under simulated solar light. The results revealed that cadmium doping greatly improved the photocatalytic efficiency of Bi{sub 2}WO{sub 6}. The Bi{sub 2}WO{sub 6} sample with R{sub Cd} = 0.05 displayed the highest photocatalytic activity, and the degradation rate is about two times greater than pure Bi{sub 2}WO{sub 6}. Moreover, the Cd–Bi{sub 2}WO{sub 6} photocatalyst remained stable even after five consecutive cycles. A possible mechanism of photocatalytic activity enhancement on basis of the experimental results was proposed.

Tungsten-based nanomaterials (WO{sub 3} & Bi{sub 2}WO{sub 6}): Modifications related to charge carrier transfer mechanisms and photocatalytic applications

Energy Technology Data Exchange (ETDEWEB)

Girish Kumar, S., E-mail: girichem@yahoo.co.in; Koteswara Rao, K.S.R., E-mail: raoksrk@gmail.com

2015-11-15

Graphical abstract: - Highlights: • Photocatalytic applications of WO{sub 3} and Bi{sub 2}WO{sub 6} based nanomaterial are reviewed. • Modifications to improve their performance are highlighted. • Charge carrier generation–separation–recombination is discussed. • Challenges and future prospects in this area are addressed. - Abstract: Heterogeneous photocatalysis is an ideal green energy technology for the purification of wastewater. Although titania dominates as the reference photocatalyst, its wide band gap is a bottleneck for extended utility. Thus, search for non-TiO{sub 2} based nanomaterials has become an active area of research in recent years. In this regard, visible light absorbing polycrystalline WO{sub 3} (2.4–2.8 eV) and Bi{sub 2}WO{sub 6} (2.8 eV) with versatile structure-electronic properties has gained considerable interest to promote the photocatalytic reactions. These materials are also explored in selective functional group transformation in organic reactions, because of low reduction and oxidation potential of WO{sub 3} CB and Bi{sub 2}WO{sub 6} VB, respectively. In this focused review, various strategies such as foreign ion doping, noble metal deposition and heterostructuring with other semiconductors designed for efficient photocatalysis is discussed. These modifications not only extend the optical response to longer wavelengths, but also prolong the life-time of the charge carriers and strengthen the photocatalyst stability. The changes in the surface-bulk properties and the charge carrier transfer dynamics associated with each modification correlating to the high activity are emphasized. The presence of oxidizing agents, surface modification with Cu{sup 2+} ions and synthesis of exposed facets to promote the degradation rate is highlighted. In depth study on these nanomaterials is likely to sustain interest in wastewater remediation and envisaged to signify in various green energy applications.

Insights into the photocatalytic mechanism of mediator-free direct Z-scheme g-C3N4/Bi2MoO6(010) and g-C3N4/Bi2WO6(010) heterostructures: A hybrid density functional theory study

Science.gov (United States)

Opoku, Francis; Govender, Krishna Kuben; Sittert, Cornelia Gertina Catharina Elizabeth van; Govender, Penny Poomani

2018-01-01

Graphite-like carbon nitride (g-C3N4)-based heterostructures have received much attention due to their prominent photocatalytic activity. The g-C3N4/Bi2WO6 and g-C3N4/Bi2MoO6 heterostructures, which follow a typical hetero-junction charge transfer mechanisms show a weak potential for hydrogen evolution and reactive radical generation under visible light irradiation. A mediator-free Z-scheme g-C3N4/Bi2MoO6(010) and g-C3N4/Bi2WO6(010) heterostructures photocatalyst are designed for the first time using first-principles studies. Moreover, theoretical understanding of the underlying mechanism, the effects of interfacial composition and the role the interface play in the overall photoactivity is still unexplained. The calculated band gap of the heterostructures is reduced compared to the bulk Bi2WO6 and Bi2MoO6. In this study, we systematically calculated energy band structure, optical properties and charge transfer of the g-C3N4/Bi2MoO6(010) and g-C3N4/Bi2WO6(010) heterostructures using the hybrid density functional theory approach. The results show that the charge transfer at the interface of the heterostructures induces a built-in potential, which benefits the separation of photogenerated charge carriers. The g-C3N4/Bi2MoO6(010) heterostructure with more negative adhesion energy (-1.10 eVA-2) is predicted to have a better adsorptive ability and can form more easily compared to the g-C3N4/Bi2WO6(010) interface (-1.16 eVA-2). Therefore, our results show that the g-C3N4 interaction with Bi2MoO6 is stronger than Bi2WO6, which is also verified by the smaller vertical separation (3.25 Å) between Bi2MoO6 and g-C3N4 compared to the g-C3N4/Bi2WO6(010) interface (3.36 Å). The optical absorption verifies that these proposed Z-scheme heterostructures are excellent visible light harvesting semiconductor photocatalyst materials. This enhancement is ascribed to the role of g-C3N4 monolayer as an electron acceptor and the direct Z-scheme charge carrier transfer at the interface of

Preparation and visible light responsive photocatalytic activity of Fe{sub 3}O{sub 4}/Ni-Al-Ce LDH/Bi{sub 2}WO{sub 6} composites

Energy Technology Data Exchange (ETDEWEB)

Hao, Jiaqi; Qu, Ting; Wang, Qiufeng; Zhao, Zhenbo, E-mail: zhaozhenbo@ccut.edu.cn [School of Chemistry and Life Science, Changchun University of Technology, Changchun, Jilin (China)

2017-09-15

Novel Fe{sub 3}O{sub 4}/Ni-Al-Ce LDH/Bi{sub 2}WO{sub 6} composites were prepared through a hydrothermal method and co-precipitation method. The morphologies and structures of the photocatalysts were characterized by XRD, Raman, TEM, UV-vis-DRS, BET surface area and VSM techniques. The photocatalytic performances of the photocatalysts were investigated by the decolorisation of methyl orange (MO) under visible-light irradiation. The results showed that the Fe{sub 3}O{sub 4}/Ni-Al-Ce LDH/Bi{sub 2}WO{sub 6} composites exhibited greater photocatalytic activities compared to pure Bi{sub 2}WO{sub 6} and the Ni-Al-Ce LDH; the decolorisation rate of MO was 87% within 60 min under visible-light irradiation. The decolorisation efficiency of the composite material remained at 71% after 4 recycling runs, showing improved stability. Furthermore, the experimental results also showed that the photocatalytic reactions for the composites followed first-order reaction kinetics. Therefore, the Fe{sub 3}O{sub 4}/Ni-Al-Ce LDH/Bi{sub 2}WO{sub 6} composites were photocatalysts with high efficiencies and stabilities for a photocatalytic reaction of an organic pollutant, and this study provides a new, effective method for the development of wastewater treatment. (author)

Construction of an all-solid-state artificial Z-scheme system consisting of Bi2WO6/Au/CdS nanostructure for photocatalytic CO2 reduction into renewable hydrocarbon fuel

Science.gov (United States)

Wang, Meng; Han, Qiutong; Li, Liang; Tang, Lanqin; Li, Haijin; Zhou, Yong; Zou, Zhigang

2017-07-01

An all-solid-state Bi2WO6/Au/CdS Z-scheme system was constructed for the photocatalytic reduction of CO2 into methane in the presence of water vapor. This Z-scheme consists of ultrathin Bi2WO6 nanoplates and CdS nanoparticles as photocatalysts, and a Au nanoparticle as a solid electron mediator offering a high speed charge transfer channel and leading to more efficient spatial separation of electron-hole pairs. The photo-generated electrons from the conduction band (CB) of Bi2WO6 transfer to the Au, and then release to the valence band (VB) of CdS to recombine with the holes of CdS. It allows the electrons remaining in the CB of CdS and holes in the VB of Bi2WO6 to possess strong reduction and oxidation powers, respectively, leading the Bi2WO6/Au/CdS to exhibit high photocatalytic reduction of CO2, relative to bare Bi2WO6, Bi2WO6/Au, and Bi2WO6/CdS. The depressed hole density on CdS also enhances the stability of the CdS against photocorrosion.

Visible-light photocatalytic activity of graphene oxide-wrapped Bi2WO6 hierarchical microspheres

Science.gov (United States)

Zhai, Jiali; Yu, Hongwen; Li, Haiyan; Sun, Lei; Zhang, Kexin; Yang, Hongjun

2015-07-01

A facile approach of fabricating homogeneous graphene oxide (GO)-wrapped Bi2WO6 microspheres (GO/Bi2WO6) is developed. The transmission electron microscopy (TEM) results show that a heterojunction interface between GO and Bi2WO6. The UV-vis diffuse reflection spectra (DRS) reveal that the as-prepared GO/Bi2WO6 composites own more intensive absorption in the visible light range compared with pure Bi2WO6. These characteristic structural and optical properties endow GO/Bi2WO6 composites with enhanced photocatalytic activity. The enhanced photocatalytic activity of the GO/Bi2WO6 is attributed predominantly to the synergetic effect between GO and Bi2WO6, causing rapid generation and separation of photo-generated charge carriers.

Interfacial properties of the enhanced visible-light plasmonic Ag/Bi{sub 2}WO{sub 6} (0 0 1) nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Wang, Fang [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu 610500 (China); The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, Chengdu 610500 (China); Cao, Kun; Wu, Yi [The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, Chengdu 610500 (China); Zhang, Kun-Hao [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201204 (China); Zhou, Ying, E-mail: yzhou@swpu.edu.cn [State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation, Southwest Petroleum University, Chengdu 610500 (China); The Center of New Energy Materials and Technology, School of Materials Science and Engineering, Southwest Petroleum University, Chengdu 610500 (China)

2016-01-01

Graphical abstract: - Highlights: • The parallel adsorption of silver on Bi{sub 2}WO{sub 6} (0 0 1) makes energetically favorable configurations. The positive charged Ag cluster may act as excited electron traps. • New isolated levels appear above the valence bands due to the hybridization of Ag 5s and O 2p, and they become dispersed as Ag content increases. This is responsible for the improved visible-light response. • Optical spectra confirm obvious red-shifts of the absorption edge with the increment of silver content, which enhances efficiently the photocatalytic activity of Bi{sub 2}WO{sub 6} (0 0 1). - Abstract: First principle calculations are performed to study the interfacial photoelectric properties of Ag{sub n}/Bi{sub 2}WO{sub 6} (0 0 1) (n = 1, 2, 3, 4) hybrid photocatalyst. The parallel adsorption of Ag cluster leads to more energetic favorable structures due to stronger interfacial interactions. The positive charged Ag cluster may act as excited electron traps and facilitate the electron–hole separation. In particular, hybridization between Ag 5s and O 2p leads to the formation of isolated energy levels above the valence bands, and they become more dispersed with broader bandwidth with the increment of silver cluster size, which is responsible for the enhanced absorption in visible-light region. In the deep valence region, Ag 4d orbital turns more delocalized and hybrid with O 2p states as the cluster size increases, which contributes to more covalent bond feature of Ag–O. Moreover, optical spectra demonstrate obvious red-shifts of the absorption edge with the increment of silver content, which enhances efficiently the visible-light photocatalytic activities of Bi{sub 2}WO{sub 6} (0 0 1). The study provides insights into the enhanced photocatalyic mechanism of Ag/Bi{sub 2}WO{sub 6} (0 0 1) and aids in the design of noble metal loaded visible-light plasmonic photocatalyst.

Visible-light photocatalytic activity of graphene oxide-wrapped Bi{sub 2}WO{sub 6} hierarchical microspheres

Energy Technology Data Exchange (ETDEWEB)

Zhai, Jiali; Yu, Hongwen, E-mail: yuhw@iga.ac.cn; Li, Haiyan; Sun, Lei; Zhang, Kexin; Yang, Hongjun

2015-07-30

Graphical abstract: - Highlights: • GO/Bi{sub 2}WO{sub 6} are readily fabricated by facile bubbling pretreatment and freeze drying. • GO/Bi{sub 2}WO{sub 6} possess excellent photocatalytic activity under visible light irradiation. • The visible light activity of GO/Bi{sub 2}WO{sub 6} is affected by the amount of GO. • The photostablity of GO is due to the photo-generated electrons transfer to Bi{sub 2}WO{sub 6}. - Abstract: A facile approach of fabricating homogeneous graphene oxide (GO)-wrapped Bi{sub 2}WO{sub 6} microspheres (GO/Bi{sub 2}WO{sub 6}) is developed. The transmission electron microscopy (TEM) results show that a heterojunction interface between GO and Bi{sub 2}WO{sub 6}. The UV–vis diffuse reflection spectra (DRS) reveal that the as-prepared GO/Bi{sub 2}WO{sub 6} composites own more intensive absorption in the visible light range compared with pure Bi{sub 2}WO{sub 6}. These characteristic structural and optical properties endow GO/Bi{sub 2}WO{sub 6} composites with enhanced photocatalytic activity. The enhanced photocatalytic activity of the GO/Bi{sub 2}WO{sub 6} is attributed predominantly to the synergetic effect between GO and Bi{sub 2}WO{sub 6}, causing rapid generation and separation of photo-generated charge carriers.

Facile synthesis of MoS{sub 2}/Bi{sub 2}WO{sub 6} nanocomposites for enhanced CO{sub 2} photoreduction activity under visible light irradiation

Energy Technology Data Exchange (ETDEWEB)

Dai, Weili, E-mail: wldai81@126.com [Key Laboratory of Jiangxi Province for Persistant Pollutants Control and Resources Recycle, Nanchang Hangkong University, Nanchang 330063, Jiangxi (China); Yu, Juanjuan [Key Laboratory of Jiangxi Province for Persistant Pollutants Control and Resources Recycle, Nanchang Hangkong University, Nanchang 330063, Jiangxi (China); Deng, Yiqiang, E-mail: dyq3211@126.com [College of Chemical Engineering, Guangdong University of Petrochemical Technology, Maoming 525000 Guangdong (China); Hu, Xu; Wang, Tengyao; Luo, Xubiao [Key Laboratory of Jiangxi Province for Persistant Pollutants Control and Resources Recycle, Nanchang Hangkong University, Nanchang 330063, Jiangxi (China)

2017-05-01

Highlights: • MoS{sub 2}/Bi{sub 2}WO{sub 6} nanocomposites (MB) were fabricated by a facile two-step approach. • MoS{sub 2} was first used as a cocatalyst coupling with Bi{sub 2}WO{sub 6} for CO{sub 2} photoreduction. • MoS{sub 2} significantly enhanced the photoelectric properties and photoactivity. • The CO{sub 3}{sup 2−}, HCO{sub 3}{sup −} and H{sub 2}CO{sub 3} in CO{sub 2} solution actually act as the reactive substrates. - Abstract: A novel composite material, MoS{sub 2}/Bi{sub 2}WO{sub 6}, has been fabricated via a facile two-step approach. The few layered MoS{sub 2} as a cocatalyst has intimate interactions with the hierarchical flower-like Bi{sub 2}WO{sub 6} microspheres, which boosts the visible light harvesting and charge transferring, and promotes the separation of electron-hole pairs, thus leading to the superior photocatalytic activity. It was found that the as-synthesized MoS{sub 2}/Bi{sub 2}WO{sub 6} nanocomposites exhibited significantly enhanced performance for the photoreduction of CO{sub 2} into hydrocarbons, i.e. methanol and ethanol, as compared with pure Bi{sub 2}WO{sub 6}. The yields of methanol and ethanol obtained over the composite with optimal content of MoS{sub 2} (0.4 wt%) were 36.7 and 36.6 μmol gcat{sup −1} after 4 h of visible light irradiation, respectively, which were 1.94 times higher than that over pure Bi{sub 2}WO{sub 6}. Furthermore, the mechanism of CO{sub 2} photoreduction was also investigated. It indicates that the CO{sub 3}{sup 2−}, HCO{sub 3}{sup −} and H{sub 2}CO{sub 3} generated in CO{sub 2} aqueous solution would be the reactive substrates during the photoreduction reaction, proving the thermodynamic feasibility of CO{sub 2} photoreduction. This work demonstrated that MoS{sub 2} is a very promising candidate for development of highly active photocatalysts, and supplied a facile and simple strategy for designing environmentally benign, cheap non-noble metal, and highly efficient semiconductor

Controlled synthesis of three-dimensional hierarchical Bi2WO6 microspheres with optimum photocatalytic activity

International Nuclear Information System (INIS)

Wang, Hong; Song, Jimei; Zhang, Hui; Gao, Fei; Zhao, Shaojuan; Hu, Haiqin

2012-01-01

Highlights: ► The synthesized method is very simple. It can be widely used in the production. ► The morphology is novel and the property is fine. ► The formation of 3D hierarchical microsphere can be induced by changing the concentration of KNO 3 . -- Abstract: Three-dimensional (3D) hierarchical Bi 2 WO 6 microsphere and octahedral Bi 2 WO 6 have been synthesized by a facile hydrothermal method using KNO 3 solution and distilled water as solvent, respectively. The obtained products were characterized by X-ray diffraction, scanning electron microscopy, N 2 adsorption/desorption, and UV–vis diffuse reflectance spectroscopy in detail. The concentration of KNO 3 played a key role in the formation of 3D hierarchical Bi 2 WO 6 microspheres. A possible formation mechanism of Bi 2 WO 6 microsphere was proposed. The photocatalytic activity of the as-synthesized products was evaluated by monitoring the degradation of MB solution under sunlight irradiation. It was found that the photocatalytic activity of the 3D hierarchical Bi 2 WO 6 microsphere was superior to the octahedral Bi 2 WO 6 , which was attributed to the larger surface area and special hierarchical structure of Bi 2 WO 6 microsphere.

Study of photocatalytic activities of Bi2WO6 nanoparticles synthesized by fast microwave-assisted method

International Nuclear Information System (INIS)

Phu, Nguyen Dang; Hoang, Luc Huy; Chen, Xiang-Bai; Kong, Meng-Hong; Wen, Hua-Chiang; Chou, Wu Ching

2015-01-01

We present a study of photocatalytic activities of Bi 2 WO 6 nanoparticles synthesized by fast microwave-assisted method. The photocatalytic activities of the nanoparticles were evaluated by the decolorization of methylene-blue under visible-light-irradiation. Our results show that the surface area of Bi 2 WO 6 nanoparticles plays a major role for improving photocatalytic activity, while visible-light absorption has only a weak effect on photocatalytic activity. This suggests efficient transportation of photo-generated electrons and holes to the oxidation active sites on the surface of nanoparticles, indicating Bi 2 WO 6 nanoparticles synthesized by fast microwave-assisted method are promising for achieving high photocatalytic activity under visible-light-irradiation. - Highlights: • The Bi 2 WO 6 nanoparticles were synthesized via fast microwave-assisted method. • The obtained Bi 2 WO 6 nanoparticles exhibited visible-light absorbance. • The surface area of Bi 2 WO 6 nanoparticles plays major role for improving photocatalytic activity. • The Bi 2 WO 6 nanoparticles are promising for achieving high photocatalytic activity under visible-light-irradiation

A plate-on-plate sandwiched Z-scheme heterojunction photocatalyst: BiOBr-Bi{sub 2}MoO{sub 6} with enhanced photocatalytic performance

Energy Technology Data Exchange (ETDEWEB)

Wang, Shengyao [College of Science, Huazhong Agricultural University, Wuhan 430070 (China); Key Laboratory of Environment Correlative Dietology, Ministry of Education, Wuhan 430070 (China); Yang, Xianglong; Zhang, Xuehao; Ding, Xing; Yang, Zixin [College of Science, Huazhong Agricultural University, Wuhan 430070 (China); Dai, Ke [College of Resources and Environment, Huazhong Agricultural University, Wuhan 430070 (China); Chen, Hao, E-mail: hchenhao@mail.hzau.edu.cn [College of Science, Huazhong Agricultural University, Wuhan 430070 (China); Key Laboratory of Environment Correlative Dietology, Ministry of Education, Wuhan 430070 (China)

2017-01-01

Highlights: • A visible light heterojunction photocatalyst of BiOBr-Bi{sub 2}MoO{sub 6} was simply synthesized. • Carriers transferred efficiently in sandwiched layers causing an enhance activity. • A possible direct Z-scheme charge transfer mechanism of BiOBr-Bi2MoO6 is proposed. - Abstract: In this study, a direct Z-scheme heterojunction BiOBr-Bi{sub 2}MoO{sub 6} with greatly enhanced visible light photocatalytic performance was fabricated via a two-step coprecipitation method. It was indicated that a plate-on-plate heterojunctions be present between BiOBr and Bi{sub 2}MoO{sub 6} through different characterization techniques including X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectroscopy (DRS) and photoelectrochemical measurements. The crystal structure and morphology analysis revealed that the heterointerface in BiOBr-Bi{sub 2}MoO{sub 6} occurred mainly on the (001) facets of BiOBr and (001) facets of Bi{sub 2}MoO{sub 6}. The photocatalytic activity of the BiOBr-Bi{sub 2}MoO{sub 6} was investigated by degradation of RhB and about 66.7% total organic carbon (TOC) could be removed. Ciprofloxacin (CIP) was employed to rule out the photosensitization. It was implied that the higher activity of BiOBr-Bi{sub 2}MoO{sub 6} could be attribute to the strong redox ability in the Z-scheme system, which was subsequently confirmed by photoluminescence spectroscopy (PL) and active spices trapping experiments. This study provides a promising platform for Z-scheme heterojunction constructing and also sheds light on highly efficient visible-light-driven photocatalysts designing.

Sol-Gel-Hydrothermal Synthesis of the Heterostructured TiO2/N-Bi2WO6 Composite with High-Visible-Light- and Ultraviolet-Light-Induced Photocatalytic Performances

Directory of Open Access Journals (Sweden)

Jiang Zhang

2012-01-01

Full Text Available The heterostructured TiO2/N-Bi2WO6 composites were prepared by a facile sol-gel-hydrothermal method. The phase structures, morphologies, and optical properties of the samples were characterized by using X-ray powder diffraction (XRD, scanning electron microscopy (SEM, high-resolution transmission electron microscopy (HRTEM, energy dispersive spectroscopy (EDS, and UV-vis diffuse reflectance spectroscopy. The photocatalytic activities for rhodamine B of the as-prepared products were measured under visible and ultraviolet light irradiation at room temperature. The TiO2/N-Bi2WO6 composites exhibited much higher photocatalytic performances than TiO2 as well as Bi2WO6. The enhancement in the visible light photocatalytic performance of the TiO2/N-Bi2WO6 composites could be attributed to the effective electron-hole separations at the interfaces of the two semiconductors, which facilitate the transfer of the photoinduced carriers.

Synthesis and Visible-Light Photocatalytic Property of Bi2WO6Hierarchical Octahedron-Like Structures

Directory of Open Access Journals (Sweden)

Li Yuanyuan

2008-01-01

Full Text Available Abstract A novel octahedron-like hierarchical structure of Bi2WO6has been fabricated by a facile hydrothermal method in high quantity. XRD, SEM, TEM, and HRTEM were used to characterize the product. The results indicated that this kind of Bi2WO6crystals had an average size of ~4 μm, constructed by quasi-square single-crystal nanosheets assembled in a special fashion. The formation of octahedron-like hierarchical structure of Bi2WO6depended crucially on the pH value of the precursor suspensions. The photocatalytic activity of the hierarchical Bi2WO6structures toward RhB degradation under visible light was investigated, and it was found to be significantly better than that of the sample fabricated by SSR. The better photocatalytic property should be strongly associated with the high specific surface area and the abundant pore structure of the hierarchical octahedron-like Bi2WO6.

In situ fabrication of novel Z-scheme Bi{sub 2}WO{sub 6} quantum dots/g-C{sub 3}N{sub 4} ultrathin nanosheets heterostructures with improved photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Chen, Wei; Liu, Tian-Yu; Huang, Ting; Liu, Xiao-Heng, E-mail: xhliu@mail.njust.edu.cn; Zhu, Jun-Wu; Duan, Guo-Rong; Yang, Xu-Jie

2015-11-15

Graphical abstract: - Highlights: • We designed and fabricated novel Bi{sub 2}WO{sub 6} QDs/g-C{sub 3}N{sub 4} heterojunction structures. • Novel Bi{sub 2}WO{sub 6} QDs/g-C{sub 3}N{sub 4} catalysts were constructed by one-pot hydrothermal route. • The catalysts show highly efficient solar light catalytic activity. • Z-scheme mechanism was proposed to explain the enhanced catalytic activity. - Abstract: The use of solar energy is a promising means for pollution abatement or environmental remediation. In the present work, we report the design and fabrication of Bi{sub 2}WO{sub 6} QDs/g-C{sub 3}N{sub 4} binary heterojunction photocatalysts with highly efficient solar light response, wherein the Bi{sub 2}WO{sub 6} QDs were in situ uniformly immobilized on porous g-C{sub 3}N{sub 4} ultrathin nanosheets (NSs) by one-pot hydrothermal strategy. The photocatalytic performance of the Bi{sub 2}WO{sub 6} QDs/g-C{sub 3}N{sub 4} NSs hybrid composites was evaluated for the photodegradation of Rhodamine B (RhB). It was found that the mass ratio of Bi{sub 2}WO{sub 6} QDs to g-C{sub 3}N{sub 4} nanosheets in the composites significantly affects the photocatalytic activity. Higher amounts of g-C{sub 3}N{sub 4} nanosheets in Bi{sub 2}WO{sub 6} QDs/g-C{sub 3}N{sub 4} composites showed lower photocatalytic activity. The composite with 10 mg g-C{sub 3}N{sub 4} nanosheets exhibited the highest photocatalytic activity, with nearly 11-fold enhancement in photocatalytic efficiency over pure Bi{sub 2}WO{sub 6} QDs. Different from previous reports, a novel Z-scheme photocatalytic mechanism was proposed to explain the enhanced the photocatalytic efficiency.

Nest-like structures of Sr doped Bi2WO6: Synthesis and enhanced photocatalytic properties

International Nuclear Information System (INIS)

Liu Ying; Wang Weimin; Fu Zhengyi; Wang Hao; Wang Yucheng; Zhang Jinyong

2011-01-01

Highlights: → Bi 2 WO 6 with 3D nest-like structures was obtained without the presence of templates but after Sr-doping, which represents a marked improvement over previous reports. → The products showed enhanced photocatalytic properties over pure Bi 2 WO 6 . → Samples subsequently thermal treated at 500 deg. C show better photocatalytic activities. - Abstract: A series of Sr-doped Bi 2 WO 6 with three-dimensional (3D) nest-like structures were synthesized through simple hydrothermal route and characterized by XRD, FESEM, TEM, XPS, UV-vis DRS, etc. Morphology observation revealed that the as-synthesized Bi 2 WO 6 were self-assembled three-dimensional (3D) nest-like structures, which were constructed from nanoplates. UV-vis diffuse reflectance spectra indicated that the samples had absorption in both UV and visible light areas. Their photocatalytic activities were evaluated by photodegradation of rhodamine B (RhB) under UV and visible light irradiation (λ > 420 nm). The photocatalytic properties were enhanced after Sr doping. Samples subsequently thermal treated at 500 deg. C showed higher photocatalytic activities. The reasons for the differences in the photocatalytic activities of these nest-like Bi 2 WO 6 microstructures were further investigated.

Electron microscopy analyses and electrical properties of the layered Bi2WO6 phase

International Nuclear Information System (INIS)

Taoufyq, A.; Ait Ahsaine, H.; Patout, L.; Benlhachemi, A.; Ezahri, M.

2013-01-01

The bismuth tungstate Bi 2 WO 6 was synthesized using a classical coprecipitation method followed by a calcination process at different temperatures. The samples were characterized by X-ray diffraction, simultaneous thermogravimetry and differential thermal analysis (TGA/DTA), scanning and transmission electron microscopy (SEM, TEM) analyses. The Rietveld analysis and electron diffraction clearly confirmed the Pca2 1 non centrosymmetric space group previously proposed for this phase. The layers Bi 2 O 2 2+ and WO 4 2− have been directly evidenced from the HRTEM images. The electrical properties of Bi 2 WO 6 compacted pellets systems were determined from electrical impedance spectrometry (EIS) and direct current (DC) analyses, under air and argon, between 350 and 700 °C. The direct current analyses showed that the conduction observed from EIS analyses was mainly ionic in this temperature range, with a small electronic contribution. Electrical change above the transition temperature of 660 °C is observed under air and argon atmospheres. The strong conductivity increase observed under argon is interpreted in terms of formation of additional oxygen vacancies coupled with electron conduction. - Graphical abstract: High resolution transmission electron microscopy: inverse fast Fourier transform giving the layered structure of the Bi 2 WO 6 phase, with a representation of the cell dimensions (b and c vectors). The Bi 2 O 2 2+ and WO 4 2− sandwiches are visible in the IFFT image. - Highlights: • Using transmission electron microscopy, we visualize the layered structure of Bi 2 WO 6 . • Electrical analyses under argon gas show some increase in conductivity. • The phase transition at 660 °C is evidenced from electrical modification

Polymorphism and properties of Bi{sub 2}WO{sub 6} doped with pentavalent antimony

Energy Technology Data Exchange (ETDEWEB)

Kharitonova, E.P.; Belov, D.A. [M.V. Lomonosov Moscow State University, Leninskie Gory, 119991 Moscow (Russian Federation); Gagor, A.B.; Pietraszko, A.P. [W. Trzebiatowski Institute of Low Temperature and Structure Research, Polish Academy of Sciences, Okólna 2, 50-950 Wrocław (Poland); Alekseeva, O.A. [Shubnikov Institute of Crystallography, Russian Academy of Sciences, Leninsky pr. 59, 119333 Moscow (Russian Federation); Voronkova, V.I., E-mail: voronk@polly.phys.msu.ru [M.V. Lomonosov Moscow State University, Leninskie Gory, 119991 Moscow (Russian Federation)

2014-04-05

Highlights: • The limit of Bi{sub 2}W{sub 1−x}Sb{sub x}O{sub 6−y} solid solutions is at x = 0.05. • Bi{sub 2}W{sub 1−x}Sb{sub x}O{sub 6−y} does not fully transform into high-temperature monoclinic phase. • Sb{sup 5+} has a weak effect on the temperatures of the ferroelectric transitions. • γ→γ{sup ‴} transition near 650 °C was observed as strong permittivity peak at 0.01–8 Hz. • The conductivity of Bi{sub 2}W{sub 0.96}Sb{sub 0.04}O{sub 6−y} at 800 °C reaches 0.02 S/cm. -- Abstract: Antimony-containing solid solutions isostructural with bismuth tungstate, Bi{sub 2}WO{sub 6}, have been prepared in air as polycrystalline samples by solid-state reactions and as single crystals by unseeded flux growth. The antimony in the solid solutions is in a pentavalent state and substitutes for tungsten in the structure of Bi{sub 2}WO{sub 6}. The Bi{sub 2}W{sub 1−x}Sb{sub x}O{sub 6−y} solid solutions have been shown to exist in the composition range 0 ⩽ x ⩽ 0.05. We have examined the effect of Sb{sup 5+} doping on the polymorphism and properties of Bi{sub 2}WO{sub 6}. In contrast to undoped Bi{sub 2}WO{sub 6}, antimony-substituted bismuth tungstate does not completely transform into its high-temperature, monoclinic phase at 960 °C and remains two-phase up to temperatures approaching its melting point. Antimony substitution for tungsten has a weak effect on the temperatures of the ferroelectric phase transitions. Heterovalent substitution of Sb{sup 5+} for W{sup 6+} is accompanied by the formation of extra oxygen vacancies and an increase in the electrical conductivity of the solid solutions by one to two orders of magnitude relative to undoped Bi{sub 2}WO{sub 6}.

Controllable Fabrication of Ordered Mesoporous Bi2WO6 and Its High Photocatalytic Activity under Visible Light

Directory of Open Access Journals (Sweden)

Xueming Dang

2014-01-01

Full Text Available Ordered mesoporous Bi2WO6 was fabricated by nanocasting technique using SBA-15 as the template. The effect of the dosage of SBA-15 on the formation of the ordered structure and the photocatalytic ability of mesoporous Bi2WO6 was discussed. It was confirmed that the ordered mesoporous structure was obtained as the dosage of SBA-15 was 0.3 g. It was found that, compared to Bi2WO6, the RhB degradation rate with ordered mesoporous Bi2WO6 was enhanced under visible light (λ>400 nm by the photocatalytic measurements. The enhanced photocatalytic performance of ordered mesoporous Bi2WO6 was attributed to its particular ordered mesoporous structure which could increase the light-harvesting efficiency, reduce the recombination of the photogenerated charge carriers, and promote the surface reaction.

Study of photocatalytic activities of Bi{sub 2}WO{sub 6} nanoparticles synthesized by fast microwave-assisted method

Energy Technology Data Exchange (ETDEWEB)

Phu, Nguyen Dang [Faculty of Physics, Hanoi National University of Education, 136 Xuanthuy, Cau Giay, Hanoi (Viet Nam); Hoang, Luc Huy, E-mail: hoanglhsp@hnue.edu.vn [Faculty of Physics, Hanoi National University of Education, 136 Xuanthuy, Cau Giay, Hanoi (Viet Nam); Chen, Xiang-Bai, E-mail: xchen@wit.edu.cn [School of Science and Laboratory of Optical Information Technology, Wuhan Institute of Technology, Wuhan 430205 (China); Kong, Meng-Hong [School of Science and Laboratory of Optical Information Technology, Wuhan Institute of Technology, Wuhan 430205 (China); Wen, Hua-Chiang; Chou, Wu Ching [Department of Electrophysics, National Chiao Tung University, Hsin-Chu 30010, Taiwan (China)

2015-10-25

We present a study of photocatalytic activities of Bi{sub 2}WO{sub 6} nanoparticles synthesized by fast microwave-assisted method. The photocatalytic activities of the nanoparticles were evaluated by the decolorization of methylene-blue under visible-light-irradiation. Our results show that the surface area of Bi{sub 2}WO{sub 6} nanoparticles plays a major role for improving photocatalytic activity, while visible-light absorption has only a weak effect on photocatalytic activity. This suggests efficient transportation of photo-generated electrons and holes to the oxidation active sites on the surface of nanoparticles, indicating Bi{sub 2}WO{sub 6} nanoparticles synthesized by fast microwave-assisted method are promising for achieving high photocatalytic activity under visible-light-irradiation. - Highlights: • The Bi{sub 2}WO{sub 6} nanoparticles were synthesized via fast microwave-assisted method. • The obtained Bi{sub 2}WO{sub 6} nanoparticles exhibited visible-light absorbance. • The surface area of Bi{sub 2}WO{sub 6} nanoparticles plays major role for improving photocatalytic activity. • The Bi{sub 2}WO{sub 6} nanoparticles are promising for achieving high photocatalytic activity under visible-light-irradiation.

Reduced graphene oxide wrapped Bi{sub 2}WO{sub 6} hybrid with ultrafast charge separation and improved photoelectrocatalytic performance

Energy Technology Data Exchange (ETDEWEB)

Wang, Huan [School of Chemical Engineering and Technology, Hebei University of Technology, Tianjin 300130, PR China (China); Liang, Yinghua, E-mail: liangyh@ncst.edu.cn [School of Chemical Engineering and Technology, Hebei University of Technology, Tianjin 300130, PR China (China); College of Chemical Engineering, North China University of Science and Technology, Tangshan 063009, PR China (China); Liu, Li; Hu, Jinshan [College of Chemical Engineering, North China University of Science and Technology, Tangshan 063009, PR China (China); Cui, Wenquan, E-mail: wkcui@163.com [College of Chemical Engineering, North China University of Science and Technology, Tangshan 063009, PR China (China)

2017-01-15

Highlights: • The rGO wrapped Bi{sub 2}WO{sub 6} photoelectrode was successfully synthesized. • The Bi{sub 2}WO{sub 6}@rGOhighlyincreasedthechargeseparationefficiency. • The photoelectrode exhibited enhanced photoelectrocatalytic degradation for RhB. - Abstract: A reduced graphene oxide (rGO) wrapped Bi{sub 2}WO{sub 6} (Bi{sub 2}WO{sub 6}@rGO) hybrid as photoelectrode for enhanced photoelectrocatalytic (PEC) degradation of organic pollutants is reported, which exhibited excellent charge separation and photoconversion efficiency. The core@shell structured Bi{sub 2}WO{sub 6}@rGO photoelectrode yielded a pronounced 1.56-fold and 23.8-fold photocurrent density at 1.0 V vs. saturated calomel electrode (SCE), than that of loading structured Bi{sub 2}WO{sub 6}-rGO and pure Bi{sub 2}WO{sub 6}. The Bi{sub 2}WO{sub 6}@rGO hybrid exhibited enhanced photoelectrocatalytic efficiency for degradation of Rhodamine B (RhB), which was 43.0% and 65.6% higher than that of photocatalytic (PC) and electrocatalytic (EC) processes, respectively. The enhancement in PEC degradation of RhB benefited from: (1) a strong interaction and a wide range of conjugation were formed in the core@shell system; (2) a 0.26 V of flat band potential was negatively shifted in case of Bi{sub 2}WO{sub 6}@rGO composite; (3) the photogenerated electrons and holes could be spatially separated by external electric potentials.

Hierarchical Bi{sub 2}WO{sub 6} architectures decorated with Pd nanoparticles for enhanced visible-light-driven photocatalytic activities

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jinniu; Chen, Tianhua [School of Physics and Information Technology, Shaanxi Normal University, Xi’an, 710062 (China); Lu, Hongbing, E-mail: hblu@snnu.edu.cn [School of Physics and Information Technology, Shaanxi Normal University, Xi’an, 710062 (China); Yang, Zhibo; Yin, Feng; Gao, Jianzhi; Liu, Qianru [School of Physics and Information Technology, Shaanxi Normal University, Xi’an, 710062 (China); Tu, Yafang [Department of Physics, Institute for Interdisciplinary Research, Jianghan University, Wuhan, 430056 (China)

2017-05-15

Highlights: • A new kind of Pd decorated Bi{sub 2}WO{sub 6} hierarchical microarchitecture was synthesized. • Pd nanoparticles remarkably improved the photocatalytic activity of Bi{sub 2}WO{sub 6}. • The photo-generated holes and ·O{sub 2}{sup −} played a crucial role in the degradation of RhB. • The photocatalytic enhancement mechanism of the Pd-Bi{sub 2}WO{sub 6} composites was proposed. - Abstract: A new kind of hierarchical Pd-Bi{sub 2}WO{sub 6} architecture decorated with different molar ratios of Pd to Bi, has been fabricated by a hydrothermal process, followed by a chemical deposition method. The photocatalytic activities of the pure Bi{sub 2}WO{sub 6} and Pd-Bi{sub 2}WO{sub 6} nanocatalyst were examined in the degradation of Rhodamine B (RhB) dyes and phenol under visible light. The photocatalytic results showed that the Pd-Bi{sub 2}WO{sub 6} nanocomposites possessed observably enhanced photocatalytic activities. Particularly, the 2.0% Pd loaded Bi{sub 2}WO{sub 6} had the highest photocatalytic activity, exhibiting a nearly complete degradation of 30 mg/L RhB and 10 mg/L phenol within only 50 and 60 min, respectively. In addition, the trapping experiment results indicated that the photo-generated holes (h{sup +}) and ·O{sub 2}{sup −} played a crucial role in the degradation of RhB. According to the experimental results, the photocatalytic degradation mechanism of Pd-Bi{sub 2}WO{sub 6} was also proposed. The enhanced photocatalytic activities were ascribed to the combined effects of the highly efficient separation of electrons and holes, improved visible light utilization and increased BET specific surface areas of the Pd-Bi{sub 2}WO{sub 6} nanocomposites.

Synthesis of Bi2WO6 nanoparticles and its electrochemical properties in different electrolytes for pseudocapacitor electrodes

International Nuclear Information System (INIS)

Nithya, V.D.; Kalai Selvan, R.; Kalpana, D.; Vasylechko, Leonid; Sanjeeviraja, C.

2013-01-01

Highlights: • A simple, economical and environmentally benign sonochemical technique was utilized for the synthesis of homogeneous Bi 2 WO 6 nanoparticles. • This is the first attempt to employ Bi 2 WO 6 as a supercapacitor electrode material. • Effect of electrolyte on the capacitive behaviour of the material is studied. • Bi 2 WO 6 displays good capacitive behaviour in 1 M KOH compared with 1 M NaOH and 1 M LiOH and possess sufficient capacity retention. • It presented an energy density of 67 Wh/kg in the potential range from −0.9 V to 0.1 V and it would be a promising negative electrode for supercapacitor. -- Abstract: Nanosized Bi 2 WO 6 particles were successfully synthesized by sonochemical method with an objective to develop an inexpensive and eco-friendly electrode material for supercapacitors. The prepared material was subjected to various thermal, structural, morphological, compositional, electrical and electrochemical studies. Bi 2 WO 6 nanoparticle with homogeneous distribution was achieved through sonochemical process. The lattice parameter and atomic positions of Bi 2 WO 6 structure were refined through Reitveld analysis. The electrochemical performance of Bi 2 WO 6 nanoparticles was investigated in various aqueous electrolytes such as 1 M NaOH, 1 M LiOH, 1 M Na 2 SO 4 , 1 M KOH and 6 M KOH solutions. Among these, the material exhibited an enhanced electrochemical performance in KOH electrolyte due to its smaller hydration sphere radius, high ionic mobility and lower equivalent series resistance. The charge–discharge studies rendered a specific capacitance of 608 F/g in 1 M KOH at a current density of 0.5 mA/cm 2 . Bi 2 WO 6 exhibited an excellent coulombic efficiency and specific capacitance of around 304 F/g at 3 mA/cm 2 in the potential range from −0.9 to 0.1 V vs Hg/HgO in 1 M KOH electrolyte. The above results assured that Bi 2 WO 6 could be utilized as suitable negative electrode material for supercapacitor applications and 1 M

Exfoliated thin Bi{sub 2}MoO{sub 6} nanosheets supported on WO{sub 3} electrode for enhanced photoelectrochemical water splitting

Energy Technology Data Exchange (ETDEWEB)

Ma, Ying; Jia, Yulong; Wang, Lina [State Key Laboratory for Oxo Synthesis & Selective Oxidation, and National Engineering Research Center for Fine Petrochemical Intermediates, Lanzhou Institute of Chemical Physics, CAS, Lanzhou 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Yang, Min [State Key Laboratory for Oxo Synthesis & Selective Oxidation, and National Engineering Research Center for Fine Petrochemical Intermediates, Lanzhou Institute of Chemical Physics, CAS, Lanzhou 730000 (China); Bi, Yingpu, E-mail: yingpubi@licp.cas.cn [State Key Laboratory for Oxo Synthesis & Selective Oxidation, and National Engineering Research Center for Fine Petrochemical Intermediates, Lanzhou Institute of Chemical Physics, CAS, Lanzhou 730000 (China); Qi, Yanxing, E-mail: qiyx@licp.cas.cn [State Key Laboratory for Oxo Synthesis & Selective Oxidation, and National Engineering Research Center for Fine Petrochemical Intermediates, Lanzhou Institute of Chemical Physics, CAS, Lanzhou 730000 (China)

2016-12-30

Highlights: • Thin Bi{sub 2}MoO{sub 6} nanosheets were prepared by microwave assisted ultrasonic separation. • The thin Bi{sub 2}MoO{sub 6} nanosheets could be more favorable to charge shift and separation. • The WO{sub 3}/thin Bi{sub 2}MoO{sub 6} exhibits superior photoelectric activity than WO{sub 3}/Bi{sub 2}MoO{sub 6} film. • The efficient photoelectric property results from facilitated charge separation. - Abstract: Thin Bi{sub 2}MoO{sub 6} nanosheets are obtained by a microwave-assisted ultrasonic separation process. After exfoliation, the thinner and uniform nanosheets with a thickness of about 10 nm were obtained. The exfoliated nanosheets would provide many amazing functionalities such as high electron mobility and quantum Hall effects. Therefore, thin Bi{sub 2}MoO{sub 6} supported on WO{sub 3} electrode (WO{sub 3}/thin Bi{sub 2}MoO{sub 6}) exhibits facilitated charge separation than pure WO{sub 3} film and the un-exfoliated Bi{sub 2}MoO{sub 6} nanosheets supported on WO{sub 3} electrode (WO{sub 3}/Bi{sub 2}MoO{sub 6}). As a result, WO{sub 3}/thin Bi{sub 2}MoO{sub 6} shows remarkably stable photocurrent density of 2.2 mA/cm{sup 2} at 0.8 V{sub SCE} in 0.1 M Na{sub 2}SO{sub 4} which is higher than that of that of WO{sub 3} (1.1 mA/cm{sup 2}) and WO{sub 3}/Bi{sub 2}MoO{sub 6} (1.5 mA/cm{sup 2}).

The enhanced photoactivity of nanosized Bi2WO6 catalyst for the degradation of 4-chlorophenol

International Nuclear Information System (INIS)

Fu Hongbo; Yao Wenqing; Zhang Liwu; Zhu Yongfa

2008-01-01

Nanosized Bi 2 WO 6 catalyst exhibited the enhanced photoactivity for the degradation of 4-chlorophenol (4-CP) under visible irradiation compared to the sample prepared by high-temperature solid reaction. The photoactivity of the catalyst was sensitive to pH variation of the suspension. Nanosized Bi 2 WO 6 catalyst showed the highest activity at pH 7.2. The photodegradation of 4-CP by nanosized Bi 2 WO 6 catalyst followed a pseudo-first-order reaction. After three recycling runs for the photodegradation of 4-CP, the activity of the catalyst did not show any significant loss, suggesting that the catalyst was stable under visible irradiation

Electron microscopy analyses and electrical properties of the layered Bi{sub 2}WO{sub 6} phase

Energy Technology Data Exchange (ETDEWEB)

Taoufyq, A. [Institut Matériaux Microélectronique et Nanosciences de Provence, IM2NP, UMR CNRS 7334, Université du Sud Toulon-Var, BP 20132, 83957, La Garde Cedex (France); Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc (Morocco); Département d‘Études des Réacteurs, Laboratoire Dosimétrie Capteurs Instrumentation, CEA Cadarache (France); Société CESIGMA—Signals and Systems, 1576 Chemin de La Planquette, F 83 130 LA GARDE (France); Ait Ahsaine, H. [Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc (Morocco); Patout, L. [Institut Matériaux Microélectronique et Nanosciences de Provence, IM2NP, UMR CNRS 7334, Université du Sud Toulon-Var, BP 20132, 83957, La Garde Cedex (France); Benlhachemi, A.; Ezahri, M. [Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc (Morocco); and others

2013-07-15

The bismuth tungstate Bi{sub 2}WO{sub 6} was synthesized using a classical coprecipitation method followed by a calcination process at different temperatures. The samples were characterized by X-ray diffraction, simultaneous thermogravimetry and differential thermal analysis (TGA/DTA), scanning and transmission electron microscopy (SEM, TEM) analyses. The Rietveld analysis and electron diffraction clearly confirmed the Pca2{sub 1} non centrosymmetric space group previously proposed for this phase. The layers Bi{sub 2}O{sub 2}{sup 2+} and WO{sub 4}{sup 2−} have been directly evidenced from the HRTEM images. The electrical properties of Bi{sub 2}WO{sub 6} compacted pellets systems were determined from electrical impedance spectrometry (EIS) and direct current (DC) analyses, under air and argon, between 350 and 700 °C. The direct current analyses showed that the conduction observed from EIS analyses was mainly ionic in this temperature range, with a small electronic contribution. Electrical change above the transition temperature of 660 °C is observed under air and argon atmospheres. The strong conductivity increase observed under argon is interpreted in terms of formation of additional oxygen vacancies coupled with electron conduction. - Graphical abstract: High resolution transmission electron microscopy: inverse fast Fourier transform giving the layered structure of the Bi{sub 2}WO{sub 6} phase, with a representation of the cell dimensions (b and c vectors). The Bi{sub 2}O{sub 2}{sup 2+} and WO{sub 4}{sup 2−} sandwiches are visible in the IFFT image. - Highlights: • Using transmission electron microscopy, we visualize the layered structure of Bi{sub 2}WO{sub 6}. • Electrical analyses under argon gas show some increase in conductivity. • The phase transition at 660 °C is evidenced from electrical modification.

Sol-gel synthesis of Bi2WO6/graphene thin films with enhanced photocatalytic performance for nitric monoxide oxidation under visible light irradiation

Science.gov (United States)

Sun, Chufeng; Wang, Yanbin; Su, Qiong

2018-06-01

Bi2WO6 and Bi2WO6/graphene thin films were fabricated by spin coating and post annealing at 600 °C for 2 h. In four different thin film samples, the graphene concentration was controlled as 0, 2, 4 and 6 wt%, respectively. The morphology, grain size and elemental distribution of the thin films were characterized by SEM and TEM. The crystallization and crystal phases were determined by XRD patterns, and the existence of graphene in Bi2WO6/graphene composite thin films were confirmed by Raman spectra. The photocatalytic performance of Bi2WO6 and Bi2WO6/graphene thin films was investigated by oxidizing NO under visible light irradiation. The results showed that Bi2WO6/graphene with 4 wt% of graphene showed the highest photocatalytic performance among all samples. This could be attributed to the increased electron conductivity with the presence of graphene. However, a further increased graphene concentration resulted in a decreased photocatalytic performance.

Microwave assisted hydrothermal synthesis of Ag/AgCl/WO3 photocatalyst and its photocatalytic activity under simulated solar light

International Nuclear Information System (INIS)

Adhikari, Rajesh; Gyawali, Gobinda; Sekino, Tohru; Wohn Lee, Soo

2013-01-01

Simulated solar light responsive Ag/AgCl/WO 3 composite photocatalyst was synthesized by microwave assisted hydrothermal process. The synthesized powders were characterized by X-Ray Diffraction (XRD) spectroscopy, X-Ray Photoelectron Spectroscopy (XPS), Transmission Electron Microscopy (TEM), Diffuse Reflectance Spectroscopy (UV–Vis DRS), and BET surface area analyzer to investigate the crystal structure, morphology, chemical composition, optical properties and surface area of the composite photocatalyst. This photocatalyst exhibited higher photocatalytic activity for the degradation of rhodamine B under simulated solar light irradiation. Dye degradation efficiency of composite photocatalyst was found to be increased significantly as compared to that of the commercial WO 3 nanopowder. Increase in photocatalytic activity of the photocatalyst was explained on the basis of surface plasmon resonance (SPR) effect caused by the silver nanoparticles present in the composite photocatalyst. Highlights: ► Successful synthesis of Ag/AgCl/WO 3 nanocomposite. ► Photocatalytic experiment was performed under simulated solar light. ► Nanocomposite photocatalyst was very active as compared to WO 3 commercial powder. ► SPR effect due to Ag nanoparticles enhanced the photocatalytic activity.

Bi3+ sensitized Y2WO6:Ln3+ (Ln=Dy, Eu, and Sm) phosphors for solar spectral conversion.

Science.gov (United States)

Huang, M N; Ma, Y Y; Xiao, F; Zhang, Q Y

2014-01-01

The phosphors of Y2WO6:Bi3+, Ln3+ (Ln=Dy, Eu and Sm) were synthesized by solid-state reaction in this study. The crystal structure, photoluminescence properties and energy transfer mechanism were investigated. By introducing Bi3+ ions, the excitation band of the phosphors was broadened to be 250-380 nm, which could be absorbed by the dye-sensitized solar cells (DSSCs). The overlap between excitation of W-O groups/Bi3+ and the emission of Ln3+ (Dy, Eu, and Sm) indicated that the probability of energy transfer from W-O groups and Bi3+ to Ln3+. The energy transfer efficiency from Bi3+ to Ln3+ (Ln=Dy, Eu and Sm) are calculated to be 16%, 20% and 58%. This work suggested that Y2WO6:Bi3+, Ln3+ (Ln=Dy, Eu and Sm) might be a promising ultraviolet-absorbing luminescent converter to enhance the photoelectrical conversion efficiency of dye-sensitized solar cells (DSSCs). Copyright © 2013 Elsevier B.V. All rights reserved.

Controllable synthesis of Bi{sub 2}WO{sub 6} nanoplate self-assembled hierarchical erythrocyte microspheres via a one-pot hydrothermal reaction with enhanced visible light photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Yang, Zhenya; Huang, Lin; Xie, Yanyu; Lin, Zheguan; Fan, Yunyan; Liu, Dan; Chen, Lu; Zhang, Zizhong, E-mail: z.zhang@fzu.edu.cn; Wang, Xuxu

2017-05-01

Highlights: • Bi{sub 2}WO{sub 6} hierarchical erythrocyte structure was designed by F{sup −}-assisted one-pot reaction. • Erythrocyte structure enhanced the visible-light photocatalytic activity of Bi{sub 2}WO{sub 6}. • Superoxide radical anions and h{sup +} were the main active species for RhB degradation. - Abstract: This work provides a simple approach of the F{sup −}-assisted one-pot hydrothermal reaction to successfully synthesize Bi{sub 2}WO{sub 6} hierarchical erythrocyte microspheres. The importance role of F{sup −} was systematically investigated by comparing different type of halogen ions, hydrothermal temperature and time. The possible growth mechanism of Bi{sub 2}WO{sub 6} hierarchical structures was proposed. The hierarchical erythrocytes were formed through the well-ordered and oriented self-assembly of thin Bi{sub 2}WO{sub 6} nanoplate primary subunits. F{sup −} ions were absorbed on Bi{sub 2}WO{sub 6} nanoplate surface to suppress the nanoplate stack but to induce a self-assembly through the edge interaction of Bi{sub 2}WO{sub 6} nanoplates into erythrocyte-like hierarchical microspheres superstructures. This erythrocyte structure narrowed the band gap energy and enhanced the visible-light photocatalytic activity of Bi{sub 2}WO{sub 6}. Moreover, superoxide radical anions and h{sup +} were revealed as the main active species responding for the RhB degradation on Bi{sub 2}WO{sub 6} under visible light irradiation.

A novel biosensor based on the direct electrochemistry of horseradish peroxidase immobilized in the three-dimensional flower-like Bi_2WO_6 microspheres

International Nuclear Information System (INIS)

Liu, Hui; Guo, Kai; Duan, Congyue; Chen, Xianjin; Zhu, Zhenfeng

2016-01-01

Three-dimensional flower-like Bi_2WO_6 microspheres (3D-Bi_2WO_6 MSs) have been synthesized through a simple hydrothermal method. The morphology and structure of 3D-Bi_2WO_6 MSs were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The 3D-Bi_2WO_6 MSs subsequently were used to immobilize horseradish peroxidase (HRP) and fabricate a mediator-free biosensor for the detection of H_2O_2. Spectroscopic and electrochemical results reveal that 3D-Bi_2WO_6 MSs constitute an excellent immobilization matrix with biocompatibility for enzymes. Meanwhile, due to unique morphology of the flower-like microspheres, the direct electron transfer of HRP is facilitated and the prepared biosensors display good performances for the detection of H_2O_2 with a wide linear range, including two linear sections: 0.5–100 μM (R"2 = 0.9983) and 100–250 μM (R"2 = 0.9981), as well as an extremely low method detection limit of 0.18 μM. - Highlights: • 3D-Bi_2WO_6 microspheres are used to fabricate a mediator-free biosensor firstly. • The biosensor displays a wide linear range of 0.5–250 μM for H_2O_2. • The biosensor exhibits a low detection limit of 0.18 μM for H_2O_2.

Monolayered Bi2WO6 nanosheets mimicking heterojunction interface with open surfaces for photocatalysis

Science.gov (United States)

Zhou, Yangen; Zhang, Yongfan; Lin, Mousheng; Long, Jinlin; Zhang, Zizhong; Lin, Huaxiang; Wu, Jeffrey C.-S.; Wang, Xuxu

2015-09-01

Two-dimensional-layered heterojunctions have attracted extensive interest recently due to their exciting behaviours in electronic/optoelectronic devices as well as solar energy conversion systems. However, layered heterojunction materials, especially those made by stacking different monolayers together by strong chemical bonds rather than by weak van der Waal interactions, are still challenging to fabricate. Here the monolayer Bi2WO6 with a sandwich substructure of [BiO]+-[WO4]2--[BiO]+ is reported. This material may be characterized as a layered heterojunction with different monolayer oxides held together by chemical bonds. Coordinatively unsaturated Bi atoms are present as active sites on the surface. On irradiation, holes are generated directly on the active surface layer and electrons in the middle layer, which leads to the outstanding performances of the monolayer material in solar energy conversion. Our work provides a general bottom-up route for designing and preparing novel monolayer materials with ultrafast charge separation and active surface.

Structure refinement of commensurately modulated bismuth tungstate, Bi2WO6

International Nuclear Information System (INIS)

Rae, A.D.; Thompson, J.G.; Withers, R.L.

1991-01-01

The displacive ferroelectric Bi 2 WO 6 [M r = 697.81, a = 5.4559 (4), b = 5.4360 (4), c = 16.4298 (17) A, Z = 4, D x = 9.512 g cm -3 , MoKα, λ = 0sun7107 A, μ = 958.6 cm -1 , F(000) = 1151.73], is described at room temperature as a commensurate modulation of an idealized Fmmm parent structure derived from an I4/mmm structure. Transmission electron microscopy clearly showed that there are coherent intergrowths of two distinct modulated variants in Bi 2 WO 6 crystals. Displacive models of inherent F2mm and Bmab symmetry are substantial and coherent over a large volume. They reduce the space-group symmetry to B2ab. A further substantial displacive mode corresponds to rotation of corner-connected WO 6 octahedra about axes parallel to c and has either of two inherent symmetries, Abam or Bbam, the difference being associated with the way this mode reduces the space-group symmetry to P2 1 ab, while the existence of the Bbam mode reduces the intensity of h + l = 2n + 1 data and acts like a stacking fault. Group theoretical analysis of the problem details how the X-ray data can be classified so as to monitor the refinement. Anomalous dispersion selects the overall sign of the F2mm mode and determines the polarity. The overall signs chosen for the Bmab and Abam symmetry components of atom displacements select between equivalent origins. The overall signs of induced modes of inherent Amam, Bbab and Ccma symmetry had to be determined by comparative refinement since the assumption that calculated phases are best estimates can retain the initial overall sign choice for these modes during least-squares refinement. Correlations between the dominant modes and the induced modes allowed a meaningful choice of signs to resolve the pseudo homometry. Only the sign of the Bbab mode was capable of self-correction during refinement. (orig./BHO)

Cooperative self-construction and enhanced optical absorption of nanoplates-assembled hierarchical Bi2WO6 flowers

International Nuclear Information System (INIS)

Liu Shengwei; Yu Jiaguo

2008-01-01

Bi 2 WO 6 hierarchical multilayered flower-like assemblies are fabricated on a large scale by a simple hydrothermal method in the presence of polymeric poly(sodium 4-styrenesulfonate). Such 3D Bi 2 WO 6 assemblies are constructed from orderly arranged 2D layers, which are further composed of a large number of interconnected nanoplates with a mean side length of ca. 50 nm. The bimodal mesopores associated with such hierarchical assembly exhibit peak mesopore size of ca. 4 nm for the voids within a layer, and peak mesopore size of ca. 40 nm corresponding to the interspaces between stacked layers, respectively. The formation process is discussed on the basis of the results of time-dependent experiments, which support a novel 'coupled cooperative assembly and localized ripening' formation mechanism. More interestingly, we have noticed that the collective effect related to such hierarchical assembly induces a significantly enhanced optical absorbance in the UV-visible region. This work may shed some light on the design of complex architectures and exploitation of their potential applications. - Graphical abstract: Bi 2 WO 6 hierarchical multilayered flower-like assemblies are fabricated on a large scale by a simple hydrothermal method in the presence of polymeric poly(sodium 4-styrenesulfonate)

Single-unit-cell layer established Bi 2 WO 6 3D hierarchical architectures: Efficient adsorption, photocatalysis and dye-sensitized photoelectrochemical performance

Energy Technology Data Exchange (ETDEWEB)

Huang, Hongwei; Cao, Ranran; Yu, Shixin; Xu, Kang; Hao, Weichang; Wang, Yonggang; Dong, Fan; Zhang, Tierui; Zhang, Yihe

2017-12-01

Single-layer catalysis sparks huge interests and gains widespread attention owing to its high activity. Simultaneously, three-dimensional (3D) hierarchical structure can afford large surface area and abundant reactive sites, contributing to high efficiency. Herein, we report an absorbing single-unit-cell layer established Bi2WO6 3D hierarchical architecture fabricated by a sodium dodecyl benzene sulfonate (SDBS)-assisted assembled strategy. The DBS- long chains can adsorb on the (Bi2O2)2+ layers and hence impede stacking of the layers, resulting in the single-unit-cell layer. We also uncovered that SDS with a shorter chain is less effective than SDBS. Due to the sufficient exposure of surface O atoms, single-unit-cell layer 3D Bi2WO6 shows strong selectivity for adsorption on multiform organic dyes with different charges. Remarkably, the single-unit-cell layer 3D Bi2WO6 casts profoundly enhanced photodegradation activity and especially a superior photocatalytic H2 evolution rate, which is 14-fold increase in contrast to the bulk Bi2WO6. Systematic photoelectrochemical characterizations disclose that the substantially elevated carrier density and charge separation efficiency take responsibility for the strengthened photocatalytic performance. Additionally, the possibility of single-unit-cell layer 3D Bi2WO6 as dye-sensitized solar cells (DSSC) has also been attempted and it was manifested to be a promising dye-sensitized photoanode for oxygen evolution reaction (ORR). Our work not only furnish an insight into designing single-layer assembled 3D hierarchical architecture, but also offer a multi-functional material for environmental and energy applications.

Bi2WO6 nanoflowers: An efficient visible light photocatalytic activity for ceftriaxone sodium degradation

Science.gov (United States)

Zhao, Yanyan; Wang, Yongbo; Liu, Enzhou; Fan, Jun; Hu, Xiaoyun

2018-04-01

The morphology-controlled synthesis of nano-structure photocatalyst have leaded a new possibility to improve their physical and chemical properties. Herein, Bi2WO6 nanocrystals (BWO) with nano-flower, nano plates, knot shape, rod like and irregular morphologies have been successfully synthesized through a highly facile hydrothermal process by simply adjusting pH values, reactive solvents and temperature. Photocatalytic activity of the as-prepared samples were evaluated by degradation of Ceftriaxone sodium under visible light irradiation (λ > 420 nm), the results indicated that all the BWO samples exhibit morphology-associated photocatalytic activity, and the 3D flowerlike-structure of BWO composed of well-ordered nano plates (BWO-D-5) displayed the outstanding photocatalytic activity. Through getting insight into the mechanism, h+ and rad O2- play major roles compared with rad OH in photocatalytic degradation process. The possible pathway of Ceftriaxone sodium and the intermediates were proposed to better understand the reaction process. Moreover, this work not only provides an example of morphology-dependent photocatalytic activity of BWO but also provides an illustrative example for removing organic pollutant molecules according to practical requirements.

A novel biosensor based on the direct electrochemistry of horseradish peroxidase immobilized in the three-dimensional flower-like Bi{sub 2}WO{sub 6} microspheres

Energy Technology Data Exchange (ETDEWEB)

Liu, Hui, E-mail: liuhui@sust.edu.cn; Guo, Kai; Duan, Congyue; Chen, Xianjin; Zhu, Zhenfeng

2016-07-01

Three-dimensional flower-like Bi{sub 2}WO{sub 6} microspheres (3D-Bi{sub 2}WO{sub 6} MSs) have been synthesized through a simple hydrothermal method. The morphology and structure of 3D-Bi{sub 2}WO{sub 6} MSs were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The 3D-Bi{sub 2}WO{sub 6} MSs subsequently were used to immobilize horseradish peroxidase (HRP) and fabricate a mediator-free biosensor for the detection of H{sub 2}O{sub 2}. Spectroscopic and electrochemical results reveal that 3D-Bi{sub 2}WO{sub 6} MSs constitute an excellent immobilization matrix with biocompatibility for enzymes. Meanwhile, due to unique morphology of the flower-like microspheres, the direct electron transfer of HRP is facilitated and the prepared biosensors display good performances for the detection of H{sub 2}O{sub 2} with a wide linear range, including two linear sections: 0.5–100 μM (R{sup 2} = 0.9983) and 100–250 μM (R{sup 2} = 0.9981), as well as an extremely low method detection limit of 0.18 μM. - Highlights: • 3D-Bi{sub 2}WO{sub 6} microspheres are used to fabricate a mediator-free biosensor firstly. • The biosensor displays a wide linear range of 0.5–250 μM for H{sub 2}O{sub 2}. • The biosensor exhibits a low detection limit of 0.18 μM for H{sub 2}O{sub 2}.

Hierarchical nanostructures assembled from ultrathin Bi2WO6 nanoflakes and their visible-light induced photocatalytic property

International Nuclear Information System (INIS)

Wang, Xiong; Tian, Peng; Lin, Ying; Li, Li

2015-01-01

Graphical abstract: Hierarchical Bi 2 WO 6 nanostructures assembled from nanoflakes were successfully synthesized by a facile hydrothermal method. The excellent photocatalytic activity and recycling performance might be mainly ascribed to the unique hierarchical nanostructures and are expected to offer the nanostructures promising applications in the field of wastewater treatment. - Highlights: • Hierarchical Bi 2 WO 6 nanostructures assembled from nanoflakes were successfully synthesized by a facile hydrothermal method. • Visible-light-induced photocatalytic efficiency of the obtained nanoarchitectures was enhanced about 6 times. • A possible mechanism was proposed. - Abstract: With the aid of ethylene glycol and sodium dodecylbenzene sulfonate, the hierarchical Bi 2 WO 6 nanoarchitectures assembled from nanoflakes could be attained by a facile solvothermal method. The synthetic strategy is versatile and environmentally friendly and a plausible growth-assembly process was proposed for the formation of the hierarchical nanostructures. The visible-light-irradiated photocatalytic activity was estimated by the degradation of rhodamine B. Compared with the sample prepared by a solid-state reaction, the visible-light-induced photocatalytic efficiency of the nanostructures was enhanced about 6 times. The photocatalysis tests show that the nanostructures exhibit excellent photocatalytic activity and recycling performance, which were mainly ascribed to the unique hierarchical nanostructures and are expected to offer promising applications in the field of wastewater treatment

Ultrathin Bi2WO6 nanosheet decorated with Pt nanoparticles for efficient formaldehyde removal at room temperature

Science.gov (United States)

Sun, Dong; Le, Yao; Jiang, Chuanjia; Cheng, Bei

2018-05-01

Two-dimensional (2D) ultrathin bismuth tungstate (Bi2WO6) nanosheets (BWO-NS) with a thickness of approximately 4.0 nm were synthesized by a one-step hydrothermal method, and decorated with platinum (Pt) nanoparticles (NPs) via an impregnation/borohydride-reduction approach. The as-prepared ultrathin Pt-BWO-NS exhibited superior catalytic activity for removing gaseous formaldehyde (HCHO) at ambient temperature, in comparison with bulk counterpart with Bi2WO6 sheet thickness of tens of nanometers. The ultrathin structure endowed the Pt-BWO-NS sample with larger specific surface area, which can provide abundant surface active sites for HCHO adsorption and facilitate the homogeneous dispersion of Pt NPs. X-ray photoelectron spectroscopy and hydrogen temperature-programmed reduction analyses revealed the interaction between the Bi2WO6 support and Pt species, which is crucial for activating surface oxygen atoms to participate in the catalytic HCHO oxidation process. By conducting in situ diffuse reflectance infrared Fourier transform spectroscopy under different atmospheres, i.e., gaseous HCHO in nitrogen or oxygen (O2), the reaction mechanism and the role of O2 were elucidated, with dioxymethylene, formate and linearly adsorbed carbon monoxide identified as the main reaction intermediates. This study may provide new enlightenment on fabricating novel 2D nanomaterials for efficient indoor air purification and potentially other environmental applications.

Structures of Bi14WO24 and Bi14MoO24 from neutron powder diffraction data

International Nuclear Information System (INIS)

Ling, C.D.; Withers, R.L.; Thompson, J.G.; Schmid, S.

1999-01-01

The (isomorphous) structures of Bi 14 WO 24 , tetradecabismuth tungsten tetracosaoxide, and Bi 14 MoO 24 , tetradecabismuth molybdenum tetracosaoxide, have been solved and refined using neutron powder diffraction data in the space group I4/m. The metal-atom array is fully ordered in terms of composition, and in terms of atomic positions deviates only slightly from a fluorite-type δ-Bi 2 O 3 -related parent structure. Three independent O-atom sites (accounting for 70 out of 78 O atoms in the unit cell) are also very close to fluorite-type parent positions. The remaining two O-atom sites, which coordinate W, exhibit partial occupancies and displacive disorder, neither of which could be better modelled by lowering of symmetry. The W site is coordinated by four O atoms in highly distorted tetrahedral coordination, the tetrahedron necessarily being orientationally disordered on that site. Nonetheless, the structure appears to be chemically reasonable. (orig.)

Heterojunction BiOI/Bi2MoO6 nanocomposite with much enhanced photocatalytic activity

International Nuclear Information System (INIS)

Li, Wen Ting; Zheng, Yi Fan; Yin, Hao Yong; Song, Xu Chun

2015-01-01

BiOI/Bi 2 MoO 6 heterostructures with different amounts of BiOI were successfully prepared via a facile deposition method. The obtained BiOI/Bi 2 MoO 6 photocatalysts exhibited much higher visible light (λ > 420 nm) induced photocatalytic activity compared with single Bi 2 MoO 6 and BiOI photocatalysts. 20 % BiOI/Bi 2 MoO 6 nanocomposite exhibited the highest photocatalytic activity with almost all RhB decomposed within 70 min. However, excess BiOI covering on the surface of Bi 2 MoO 6 can inversely reduce the photocatalytic activity. The enhanced photocatalytic activities could be resulted from the function of the novel p–n heterojunction interface between Bi 2 MoO 6 and BiOI, which could separate photoinduced carriers efficiently. Possible mechanisms on the basis of the relative band positions were also discussed

Enhanced photocatalytic degradation of norfloxacin in aqueous Bi2WO6 dispersions containing nonionic surfactant under visible light irradiation

International Nuclear Information System (INIS)

Tang, Lin; Wang, Jiajia; Zeng, Guangming; Liu, Yani; Deng, Yaocheng; Zhou, Yaoyu; Tang, Jing; Wang, Jingjing; Guo, Zhi

2016-01-01

Highlights: • TX100 strongly enhanced the adsorption and photodegradation of NOF in Bi 2 WO 6 dispersions under visible light irradiation (400–750 nm). • Cu 2+ (10 mM) significantly suppressed the photocatalytic degradation of NOF. • FT-IR demonstrated that the NOF adsorbed on Bi 2 WO 6 was completely degraded. • Three possible photocatalytic degradation pathways of NOF were proposed, according to the HPLC/MS/MS analysis. - Abstract: Photocatalytic degradation is an alternative method to remove pharmaceutical compounds in water, however it is hard to achieve efficient rate because of the poor solubility of pharmaceutical compounds in water. This study investigated the photodegradation of norfloxacin in a nonionic surfactant Triton-X100 (TX100)/Bi 2 WO 6 dispersion under visible light irradiation (400–750 nm). It was found that the degradation of poorly soluble NOF can be strongly enhanced with the addition of TX100. TX100 was adsorbed strongly on Bi 2 WO 6 surface and accelerated NOF photodegradation at the critical micelle concentration (CMC = 0.25 mM). Higher TX100 concentration (>0.25 mM) lowered the degradation rate. In the presence of TX100, the degradation rate reached the maximum value when the pH value was 8.06. FTIR analyses demonstrated that the adsorbed NOF on the catalyst was completely degraded after 2 h irradiation. According to the intermediates identified by HPLC/MS/MS, three possible degradation pathways were proposed to include addition of hydroxyl radical to quinolone ring, elimination of piperazynilic ring in fluoroquinolone molecules, and replacement of F atoms on the aromatic ring by hydroxyl radicals.

Visible-light CO{sub 2} photocatalytic reduction performance of ball-flower-like Bi{sub 2}WO{sub 6} synthesized without organic precursor: Effect of post-calcination and water vapor

Energy Technology Data Exchange (ETDEWEB)

Sun, Zhuxing; Yang, Zhenmei; Liu, Hongfeng [Department of Environmental Engineering, Zhejiang University, Hangzhou 310058 (China); Zhejiang Provincial Engineering Research Center of Industrial Boiler and Furnace Flue Gas Pollution Control, Hangzhou 311202 (China); Wang, Haiqiang, E-mail: wanghaiqiang2008@126.com [Department of Environmental Engineering, Zhejiang University, Hangzhou 310058 (China); Zhejiang Provincial Engineering Research Center of Industrial Boiler and Furnace Flue Gas Pollution Control, Hangzhou 311202 (China); Wu, Zhongbiao, E-mail: zbwu@zju.edu.cn [Department of Environmental Engineering, Zhejiang University, Hangzhou 310058 (China); Zhejiang Provincial Engineering Research Center of Industrial Boiler and Furnace Flue Gas Pollution Control, Hangzhou 311202 (China)

2014-10-01

Graphical abstract: - Highlights: • Photocatalytic CO{sub 2} reduction on non-organic synthesized PB-Bi{sub 2}WO{sub 6} was investigated. • CO was detected as the major product. • Increased amount of CO was yielded in the condition with little water vapor. • Photocatalytic performance was enhanced with Bi{sub 2}WO{sub 6} after 550 °C post-annealing. • Renewing the catalysts used in CO{sub 2} photoreduction by water washing was achieved. - Abstract: Nanoplates-composed ball-flower-like Bi{sub 2}WO{sub 6} (PB-Bi{sub 2}WO{sub 6}) was synthesized by a hydrothermal method without any organic precursor and its performance in photocatalytic reduction of CO{sub 2} was investigated in a continuous-flow reaction system under visible light irradiation (420 nm < λ < 620 nm). CO was detected as the main product of this photocatalytic process and H{sub 2}O was found to suppress the conversion of CO{sub 2} to CO due to its competitive absorption with CO{sub 2} on the medium strength basic sites of Bi{sub 2}WO{sub 6}. PB-Bi{sub 2}WO{sub 6} annealed at 550 °C showed superior CO yield in the condition with little water vapor. It might be attributed to the enhanced crystallinity, significantly decreased recombination rate of photo-generated electrons and holes and more stable basic sites for strengthened CO{sub 2} adsorption, according to characterization results by XRD, SEM, UV–vis SRS, PL and CO{sub 2}-TPD. However, comparing with PB-Bi{sub 2}WO{sub 6}, the negative effect of H{sub 2}O was even more prominent on the annealed sample because of the reduced surface area. Yield decrease was observed during the irradiation time due to the adsorption of intermediates generated but fortunately washing with deionized water was found to be an effective way to renew the catalyst.

Efficient Visible-Light-Driven Z-Scheme Overall Water Splitting Using a MgTa2O(6-x)N(y)/TaON Heterostructure Photocatalyst for H2 Evolution.

Science.gov (United States)

Chen, Shanshan; Qi, Yu; Hisatomi, Takashi; Ding, Qian; Asai, Tomohiro; Li, Zheng; Ma, Su Su Khine; Zhang, Fuxiang; Domen, Kazunari; Li, Can

2015-07-13

An (oxy)nitride-based heterostructure for powdered Z-scheme overall water splitting is presented. Compared with the single MgTa2O(6-x)N(y) or TaON photocatalyst, a MgTa2O(6-x)N(y)/TaON heterostructure fabricated by a simple one-pot nitridation route was demonstrated to effectively suppress the recombination of carriers by efficient spatial charge separation and decreased defect density. By employing Pt-loaded MgTa2O(6-x)N(y)/TaON as a H2-evolving photocatalyst, a Z-scheme overall water splitting system with an apparent quantum efficiency (AQE) of 6.8% at 420 nm was constructed (PtO(x)-WO3 and IO3(-)/I(-) pairs were used as an O2-evolving photocatalyst and a redox mediator, respectively), the activity of which is circa 7 or 360 times of that using Pt-TaON or Pt-MgTa2O(6-x)N)y) as a H2-evolving photocatalyst, respectively. To the best of our knowledge, this is the highest AQE among the powdered Z-scheme overall water splitting systems ever reported. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Electrosprayed heterojunction WO{sub 3}/BiVO{sub 4} films with nanotextured pillar structure for enhanced photoelectrochemical water splitting

Energy Technology Data Exchange (ETDEWEB)

Mali, Mukund G.; Yoon, Hyun; Yoon, Sam S., E-mail: skyoon@korea.ac.kr [School of Mechanical Engineering, Korea University, Seoul 136-713 (Korea, Republic of); Kim, Min-woo [School of Mechanical Engineering, Korea University, Seoul 136-713 (Korea, Republic of); Green School, Korea University, Seoul 136-713 (Korea, Republic of); Swihart, Mark T. [Department of Chemistry and Biological Engineering, University at Buffalo (SUNY), Buffalo, New York 14260 (United States); Al-Deyab, Salem S. [Department of Chemistry, College of Science, King Saud University, Riyadh 11451 (Saudi Arabia)

2015-04-13

We demonstrate that the addition of a tungsten oxide (WO{sub 3}) layer beneath a bismuth vanadate (BiVO{sub 4}) photocatalyst layer with a nanotextured pillar morphology significantly increases the photocurrent density in photoelectrochemical water splitting. The WO{sub 3}-BiVO{sub 4} bilayer films produced a photocurrent of up to 3.3 mA/cm{sup 2} under illumination at 100 mW/cm{sup 2} (AM1.5 spectrum). The bilayer film was characterized by scanning electron microscopy, X-ray diffraction, and photoelectrochemical methods, which confirmed the superiority of the bilayer film in terms of its morphology and charge separation and transport ability. Both WO{sub 3} and BiVO{sub 4} were deposited by electrostatic spraying under open-air conditions, which resulted in nanotextured pillars of BiVO{sub 4} atop a smooth WO{sub 3} film. The optimal coating conditions are also reported.

Neutron Powder Diffraction Studies of Ca2-xSrxCoWO6 Double Perovskites

International Nuclear Information System (INIS)

Zhou, Qingdi; Kennedy, Brendan; Elcombe, Margaret

2005-01-01

Full text: A series of double perovskite compounds of A 2-x Sr x CoWO 6 (A = Ca, Ba) were synthesized and the room- and variable-temperature structural phase transitions have been studied by synchrotron and neutron powder diffraction techniques. These studies demonstrated that the symmetry increases as the average size of the A-site cation increases. These transitions are associated with the gradual reduction and ultimately removal of the octahedral tiles of the BO 6 octahedra. Temperature dependent structural studies have been undertaken for selected samples. The transition to cubic is continuous in the three Ca doped samples studied as a function of temperature, Ca 2-x Sr x CoWO 6 x = 1.8, 1.7, 1.6, however in each case analysis of the spontaneous strain shows the transition to be tricritical rather than second order in nature. Where observed the temperature induced P2 1 /n to I4/m transition is first order as required by symmetry. (authors)>>>>

Enhanced photocatalytic degradation of norfloxacin in aqueous Bi{sub 2}WO{sub 6} dispersions containing nonionic surfactant under visible light irradiation

Energy Technology Data Exchange (ETDEWEB)

Tang, Lin, E-mail: tanglin@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Wang, Jiajia [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Zeng, Guangming, E-mail: zgming@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Liu, Yani; Deng, Yaocheng; Zhou, Yaoyu; Tang, Jing; Wang, Jingjing; Guo, Zhi [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China)

2016-04-05

Highlights: • TX100 strongly enhanced the adsorption and photodegradation of NOF in Bi{sub 2}WO{sub 6} dispersions under visible light irradiation (400–750 nm). • Cu{sup 2+} (10 mM) significantly suppressed the photocatalytic degradation of NOF. • FT-IR demonstrated that the NOF adsorbed on Bi{sub 2}WO{sub 6} was completely degraded. • Three possible photocatalytic degradation pathways of NOF were proposed, according to the HPLC/MS/MS analysis. - Abstract: Photocatalytic degradation is an alternative method to remove pharmaceutical compounds in water, however it is hard to achieve efficient rate because of the poor solubility of pharmaceutical compounds in water. This study investigated the photodegradation of norfloxacin in a nonionic surfactant Triton-X100 (TX100)/Bi{sub 2}WO{sub 6} dispersion under visible light irradiation (400–750 nm). It was found that the degradation of poorly soluble NOF can be strongly enhanced with the addition of TX100. TX100 was adsorbed strongly on Bi{sub 2}WO{sub 6} surface and accelerated NOF photodegradation at the critical micelle concentration (CMC = 0.25 mM). Higher TX100 concentration (>0.25 mM) lowered the degradation rate. In the presence of TX100, the degradation rate reached the maximum value when the pH value was 8.06. FTIR analyses demonstrated that the adsorbed NOF on the catalyst was completely degraded after 2 h irradiation. According to the intermediates identified by HPLC/MS/MS, three possible degradation pathways were proposed to include addition of hydroxyl radical to quinolone ring, elimination of piperazynilic ring in fluoroquinolone molecules, and replacement of F atoms on the aromatic ring by hydroxyl radicals.

Ternary reduced-graphene-oxide/Bi2MoO6/Au nanocomposites with enhanced photocatalytic activity under visible light

International Nuclear Information System (INIS)

Bi, Jinhong; Fang, Wei; Li, Li; Li, Xiaofen; Liu, Minghua; Liang, Shijing; Zhang, Zizhong; He, Yunhui; Lin, Huaxiang; Wu, Ling; Liu, Shengwei; Wong, Po Keung

2015-01-01

A novel ternary nanocomposite photocatalyst consisted of reduced-graphene-oxide (RGO), Bi 2 MoO 6 and plasmonic Au nanoparticles were successfully fabricated by multiple steps including a simple solvothermal process and photochemical reduction process. RGO/Bi 2 MoO 6 /Au was characterized by X-ray powder diffraction patterns, transmission electron microscopy, UV–vis diffuse reflectance spectra, Raman spectroscopy and X-ray photoelectron spectroscopy. In comparison with Bi 2 MoO 6 , RGO/Bi 2 MoO 6 and Au/Bi 2 MoO 6 , RGO/Bi 2 MoO 6 /Au exhibits an enhanced photocatalytic activity for decomposition of Rhodamine B under visible light. The separation efficiency of the photogenerated holes and electrons on Bi 2 MoO 6 is promoted by the combined effect of both RGO and Au in the ternary composite, and thus enhances photocatalytic activity. The scavenger study revealed that both hole and superoxide are the major reactive species for the photocatalytic degradation of Rhodamine B using RGO/Bi 2 MoO 6 /Au photocatalyst. - Graphical abstract: A novel ternary nanocomposite photocatalyst consisted of reduced-graphene-oxide (RGO), Bi 2 MoO 6 and plasmonic Au nanoparticles were successfully fabricated by multiple steps including a simple solvothermal process and photochemical reduction process. The resulted ternary nanocomposites greatly enhanced the visible light photocatalytic properties compared to Bi 2 MoO 6 , RGO/Bi 2 MoO 6 or Au/Bi 2 MoO 6 binary systems. The improved photocatalytic activity was mainly attributed to the synergistic effect of Au and RGO with better separation of the photogenerated holes and electrons, resulting from the surface plasmonic resonance and extra strong electron magnetic field of Au nanoparticles and the high electron conductivity of RGO. - Highlights: • The ternary nanocomposites RGO/Bi 2 MoO 6 /Au were constructed for the first time. • RGO/Bi 2 MoO 6 /Au showed much higher visible photoactivity than RGO (Au)/Bi 2 MoO 6 . • The improved

Sodium citrate-assisted anion exchange strategy for construction of Bi2O2CO3/BiOI photocatalysts

International Nuclear Information System (INIS)

Song, Peng-Yuan; Xu, Ming; Zhang, Wei-De

2015-01-01

Highlights: • Heterostructured Bi 2 O 2 CO 3 /BiOI microspheres were prepared via anion exchange. • Sodium citrate-assisted anion exchange for construction of composite photocatalysts. • Bi 2 O 2 CO 3 /BiOI composites show high visible light photocatalytic activity. - Abstract: Bi 2 O 2 CO 3 /BiOI heterojuncted photocatalysts were constructed through a facile partial anion exchange strategy starting from BiOI microspheres and urea with the assistance of sodium citrate. The content of Bi 2 O 2 CO 3 in the catalysts was regulated by modulating the amount of urea as a precursor, which was decomposed to generate CO 3 2− in the hydrothermal process. Citrate anion plays a key role in controlling the morphology and composition of the products. The Bi 2 O 2 CO 3 /BiOI catalysts display much higher photocatalytic activity than pure BiOI and Bi 2 O 2 CO 3 towards the degradation of rhodamine B (RhB) and bisphenol A (BPA). The enhancement of photocatalytic activity of the heterojuncted catalysts is attributed to the formation of p–n junction between p-BiOI and n-Bi 2 O 2 CO 3 , which is favorable for retarding the recombination of photoinduced electron-hole pairs. Moreover, the holes are demonstrated to be the main active species for the degradation of RhB and BPA

Easily recycled Bi2O3 photocatalyst coatings prepared via ball milling followed by calcination

Science.gov (United States)

Cheng, Lijun; Hu, Xumin; Hao, Liang

2017-06-01

Bi2O3 photocatalyst coatings derived from Bi coatings were first prepared by a two-step method, namely ball milling followed by the calcination process. The as-prepared samples were characterized by XRD, SEM, XPS and UV-Vis spectra, respectively. The results showed that monoclinic Bi2O3 coatings were obtained after sintering Bi coatings at 673 or 773 K, while monoclinic and triclinic mixed phase Bi2O3 coatings were obtained at 873 or 973 K. The topographies of the samples were observably different, which varied from flower-like, irregular, polygonal to nanosized particles with the increase in calcination temperature. Photodegradation of malachite green under simulated solar irradiation for 180 min showed that the largest degradation efficiency of 86.2% was achieved over Bi2O3 photocatalyst coatings sintered at 873 K. The Bi2O3 photocatalyst coatings, encapsulated with Al2O3 ball with an average diameter around 1 mm, are quite easily recycled, which provides an alternative visible light-driven photocatalyst suitable for practical water treatment application.

Insights into the photocatalytic mechanism of mediator-free direct Z-scheme g-C3N4/Bi2MoO6(010) and g-C3N4/Bi2WO6(010) heterostructures: A hybrid density functional theory study

CSIR Research Space (South Africa)

Opoku, F

2018-01-01

Full Text Available Graphite-like carbon nitride (g-C3N4)-based heterostructures have received much attention due to their prominent photocatalytic activity. The g-C3N4/Bi2WO6 and g-C3N4/Bi2MoO6 heterostructures, which follow a typical hetero-junction charge transfer...

Heterostructured Fe3O4/Bi2O2CO3 photocatalyst: Synthesis, characterization and application in recyclable photodegradation of organic dyes under visible light irradiation

International Nuclear Information System (INIS)

Zhu, Gangqiang; Hojamberdiev, Mirabbos; Katsumata, Ken-ichi; Cai, Xu; Matsushita, Nobuhiro; Okada, Kiyoshi; Liu, Peng; Zhou, Jianping

2013-01-01

Heterostructured Fe 3 O 4 /Bi 2 O 2 CO 3 photocatalyst was synthesized by a two-step method. First, Fe 3 O 4 nanoparticles with the size of ca. 10 nm were synthesized by chemical method at room temperature and then heterostructured Fe 3 O 4 /Bi 2 O 2 CO 3 photocatalyst was synthesized by hydrothermal method at 180 °C for 24 h with the addition of 10 wt% Fe 3 O 4 nanoparticles into the precursor suspension of Bi 2 O 2 CO 3 . The pH value of synthesis suspension was adjusted to 4 and 6 with the addition of 2 M NaOH aqueous solution. By controlling the pH of synthesis suspension at 4 and 6, sphere- and flower-like Fe 3 O 4 /Bi 2 O 2 CO 3 photocatalysts were obtained, respectively. Both photocatalysts demonstrate superparamagnetic behavior at room temperature. The UV–vis diffuse reflectance spectra of the photocatalysts confirm that all the heterostructured photocatalysts are responsive to visible light. The photocatalytic activity of the heterostructured photocatalysts was evaluated for the degradation of methylene blue (MB) and methyl orange (MO) in aqueous solution over the photocatalysts under visible light irradiation. The heterostructured photocatalysts prepared in this study exhibit highly efficient visible-light-driven photocatalytic activity for the degradation of MB and MO, and they can be easily recovered by applying an external magnetic field. - Highlights: • Sphere- and flower-like Fe 3 O 4 /Bi 2 O 2 CO 3 was synthesized by hydrothermal method. • Fe 3 O 4 nanoparticles with the size of ca. 10 nm were synthesized by chemical method. • Photocatalysts demonstrate superparamagnetic behavior at room temperature. • Photocatalysts exhibit highly efficient visible-light-driven photocatalytic activity. • Photocatalysts can be easily recovered by applying an external magnetic field

Preparation and characterization of Fe3O4/SiO2/Bi2MoO6 composite as magnetically separable photocatalyst

International Nuclear Information System (INIS)

Hou, Xuemei; Tian, Yanlong; Zhang, Xiang; Dou, Shuliang; Pan, Lei; Wang, Wenjia; Li, Yao; Zhao, Jiupeng

2015-01-01

Highlights: • Fe 3 O 4 /SiO 2 /Bi 2 MoO 6 composite was prepared by a hydrothermal method. • The composite has an enhanced visible absorption compared with pure Bi 2 MoO 6 . • The magnetic photocatalyst displayed excellent stability and reusability. • O 2 ·− and · OH play a major role during the photocatalytic process. - Abstract: In this paper, Fe 3 O 4 /SiO 2 /Bi 2 MoO 6 microspheres were prepared by a facile hydrothermal method. The scanning electron microscope (SEM) results revealed that flower-like three dimensional (3D) Bi 2 MoO 6 microspheres were decorated with Fe 3 O 4 /SiO 2 magnetic nanoparticles. The UV–vis diffuse reflection spectra showed extended absorption within the visible light range compared with pure Bi 2 MoO 6 . We evaluated the photocatalytic activities of Fe 3 O 4 /SiO 2 /Bi 2 MoO 6 microspheres on the degradation of Rhodamine B (RhB) under visible light irradiation and found that the obtained composite exhibited higher photocatalytic activity than pure Bi 2 MoO 6 and P25. Moreover, the Fe 3 O 4 /SiO 2 /Bi 2 MoO 6 composite also displayed excellent stability and their photocatalytic activity decreased slightly after reusing 5 cycles. Meanwhile, the composite could be easily separated by applying an external magnetic field. The trapping experiment results suggest that superoxide radical species O 2 ·− and hydroxyl radicals · OH play a major role in Fe 3 O 4 /SiO 2 /Bi 2 MoO 6 system under visible light irradiation. The combination of flower-like three dimensional (3D) Bi 2 MoO 6 microspheres and Fe 3 O 4 /SiO 2 magnetic nanospheres provides a useful strategy for designing multifunctional nanostructure materials with enhanced photocatalytic activities in the potential applications of water purification

Ag2WO4 nanorods decorated with AgI nanoparticles: Novel and efficient visible-light-driven photocatalysts for the degradation of water pollutants

Directory of Open Access Journals (Sweden)

Shijie Li

2018-04-01

Full Text Available To develop efficient and stable visible-light-driven (VLD photocatalysts for pollutant degradation, we synthesized novel heterojunction photocatalysts comprised of AgI nanoparticle-decorated Ag2WO4 nanorods via a facile method. Various characterization techniques, including XRD, SEM, TEM, EDX, and UV–vis DRS were used to investigate the morphology and optical properties of the as-prepared AgI/Ag2WO4 catalyst. With AgI acting as the cocatalyst, the resulting AgI/Ag2WO4 heterostructure shows excellent performance in degrading toxic, stable pollutants such as rhodamine B (RhB, methyl orange (MO and para-chlorophenol (4-CP. The high performance is attributed to the enhanced visible-light absorption properties and the promoted separation efficiency of charge carriers through the formation of the heterojunction between AgI and Ag2WO4. Additionally, AgI/Ag2WO4 exhibits durable stability. The active species trapping experiment reveals that active species (O2•− and h+ dominantly contribute to RhB degradation. The AgI/Ag2WO4 heterojunction photocatalyst characterized in this work holds great potential for remedying environmental issues due to its simple preparation method and excellent photocatalytic performance.

Diatomite-immobilized BiOI hybrid photocatalyst: Facile deposition synthesis and enhanced photocatalytic activity

Science.gov (United States)

Li, Baoying; Huang, Hongwei; Guo, Yuxi; Zhang, Yihe

2015-10-01

A novel diatomite-immobilized BiOI hybrid photocatalyst has been prepared by a facile one-step deposition process for the first time. The structure, morphology and optical property of the products were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and UV-vis diffuse reflectance spectroscopy (DRS). The photocatalytic performance of the as-prepared BiOI/diatomite photocatalysts was studied by photodegradation of Rhodamine B (RhB) and methylene blue (MB) and monitoring photocurrent generation under visible light (λ > 420 nm). The results revealed that BiOI/diatomite composites exhibit enhanced photocatalytic activity compared to the pristine BiOI sample. This enhancement should be attributed to that diatomite can play as an excellent carrier platform to increase the reactive sites and promote the separation of photogenerated electron-hole pairs. In addition, the corresponding photocatalytic mechanism was proposed based on the active species trapping experiments. This work shed new light on facile fabrication of novel composite photocatalyst based on natural mineral.

Diatomite-immobilized BiOI hybrid photocatalyst: Facile deposition synthesis and enhanced photocatalytic activity

International Nuclear Information System (INIS)

Li, Baoying; Huang, Hongwei; Guo, Yuxi; Zhang, Yihe

2015-01-01

Graphical abstract: - Highlights: • A novel diatomite-immobilized BiOI hybrid photocatalyst has been prepared by a facile one-step deposition process for the first time. • The diatomite-immobilized BiOI hybrid photocatalyst exhibits much better photocatalytic performance. • This enhancement should be attributed to that diatomite can play as an excellent carrier platform to increase the reactive sites and promote the separation of photogenerated electron–hole pairs. • This work shed new light on facile fabrication of novel composite photocatalyst based on natural mineral. - Abstract: A novel diatomite-immobilized BiOI hybrid photocatalyst has been prepared by a facile one-step deposition process for the first time. The structure, morphology and optical property of the products were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic performance of the as-prepared BiOI/diatomite photocatalysts was studied by photodegradation of Rhodamine B (RhB) and methylene blue (MB) and monitoring photocurrent generation under visible light (λ > 420 nm). The results revealed that BiOI/diatomite composites exhibit enhanced photocatalytic activity compared to the pristine BiOI sample. This enhancement should be attributed to that diatomite can play as an excellent carrier platform to increase the reactive sites and promote the separation of photogenerated electron–hole pairs. In addition, the corresponding photocatalytic mechanism was proposed based on the active species trapping experiments. This work shed new light on facile fabrication of novel composite photocatalyst based on natural mineral.

Diatomite-immobilized BiOI hybrid photocatalyst: Facile deposition synthesis and enhanced photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Li, Baoying; Huang, Hongwei, E-mail: hhw@cugb.edu.cn; Guo, Yuxi; Zhang, Yihe, E-mail: zyh@cugb.edu.cn

2015-10-30

Graphical abstract: - Highlights: • A novel diatomite-immobilized BiOI hybrid photocatalyst has been prepared by a facile one-step deposition process for the first time. • The diatomite-immobilized BiOI hybrid photocatalyst exhibits much better photocatalytic performance. • This enhancement should be attributed to that diatomite can play as an excellent carrier platform to increase the reactive sites and promote the separation of photogenerated electron–hole pairs. • This work shed new light on facile fabrication of novel composite photocatalyst based on natural mineral. - Abstract: A novel diatomite-immobilized BiOI hybrid photocatalyst has been prepared by a facile one-step deposition process for the first time. The structure, morphology and optical property of the products were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic performance of the as-prepared BiOI/diatomite photocatalysts was studied by photodegradation of Rhodamine B (RhB) and methylene blue (MB) and monitoring photocurrent generation under visible light (λ > 420 nm). The results revealed that BiOI/diatomite composites exhibit enhanced photocatalytic activity compared to the pristine BiOI sample. This enhancement should be attributed to that diatomite can play as an excellent carrier platform to increase the reactive sites and promote the separation of photogenerated electron–hole pairs. In addition, the corresponding photocatalytic mechanism was proposed based on the active species trapping experiments. This work shed new light on facile fabrication of novel composite photocatalyst based on natural mineral.

Fabrication of the heterostructured CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} hybrid photocatalyst with enhanced performance of photocatalytic hydrogen production from water

Energy Technology Data Exchange (ETDEWEB)

Lang, Junyu; Liu, Mengqing; Su, Yiguo; Yan, Lijuan; Wang, Xiaojing, E-mail: wang_xiao_jing@hotmail.com

2015-12-15

Graphical abstract: - Highlights: • A novel ternary CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} hybrid photocatalyst was successfully fabricated. • Au particles act as an electron-conduction bridge between the heterostructure. • The photoctalytic hydrogen generation was promoted by the SPR of the Au. • CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} shows significant photocatalytic activity in H{sub 2} generation. - Abstract: In this work, a novel CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} hybrid photocatalyst is successfully fabricated. The photocatalytic performance of the heterostructured CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} composite was investigated. Au nanoparticles were photo-deposited as the interlayer between g-C{sub 3}N{sub 4} and the surface of CsTaWO{sub 6}, which can facilitate the photoinduced electrons migration as an electron-conduction bridge as well as increase visible-light absorption via the surface plasmon resonance. This heterostructured interface bridging by Au particles may significantly retard the recombination of electron–holes, which is beneficial to promote the photocatalytic activity under visible-light irradiation. It is found the CsTaWO{sub 6}/Au/g-C{sub 3}N{sub 4} sample showed excellent photocatalytic activity of water splitting, even higher than the sum of g-C{sub 3}N{sub 4} and Au/CsTaWO{sub 6} samples, or the sum of CsTaWO{sub 6} and Au/g-C{sub 3}N{sub 4} samples. It indicates that the heterostructured combination of g-C{sub 3}N{sub 4} and CsTaWO{sub 6} bridging by Au particles provided the synergistic photocatalytic activity driving by solar light through an efficient electron transfer process.

Synthesis and photocatalytic properties of MgBi2O6 with Ag additions

Science.gov (United States)

Zhong, Liansheng; Hu, Chaohao; Zhu, Binqing; Zhong, Yan; Zhou, Huaiying

2018-02-01

Ag-doped MgBi2O6 photocatalysts were synthesized by the low temperature hydrothermal method in combination with heat treatment reaction using NaBiO3·2H2O, MgCl2·6H2O, and AgNO3 as raw materials. The products were characterized by using power X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), Energy dispersive X-ray detector (EDS), and UV-Vis diffusion reflectance spectra. The photocatalytic activity of MgBi2O6 with Ag additions was evaluated by degrading MB (10 mg/L) under visible light irradiation (λ > 420 nm). The results showed that in comparison with pure MgBi2O6, the photocatalytic activity of MgBi2O6 with about 5% Ag concentration is increased by about 24% after 120 min reaction. The enhancement of catalytic activity of Ag-doped MgBi2O6 photocatalysts should be related to the band structure, morphology and larger specific surface area.

The luminescence of CaWO4: Bi single crystals

International Nuclear Information System (INIS)

Zorenko, Yu.; Pashkovsky, M.; Voloshinovskii, A.; Kuklinski, B.; Grinberg, M.

2006-01-01

Influence of doping with Bi 3+ ions and Bi 3+ -Na + or Bi 3+ -Li + ions pairs on luminescence, emission kinetics and light yield of CaWO 4 crystals has been investigated. It has been shown that under excitation in the A-band at 272 and 287nm, related to the Bi 3+ ions absorption, the luminescence peaked at 468nm decaying with time τ=0.41μs is observed. For bismuth concentration 50-500ppm and the equimolar concentrations of the Bi 3+ ions accompanied by Na + or Li + ions compensators the significant suppression of the phosphorescence peaked at 520nm, related to the defect WO 3 -V O complex, and an improvement of scintillation characteristics of the CaWO 4 are noticed. Energy transfer from the defect WO 3 -V O and regular WO 4 2- oxy-anions to Bi 3+ ions have been observed at room temperatures and discussed

One pot hydrothermal synthesis of a novel BiIO4/Bi2MoO6 heterojunction photocatalyst with enhanced visible-light-driven photocatalytic activity for rhodamine B degradation and photocurrent generation

International Nuclear Information System (INIS)

Huang, Hongwei; Liu, Liyuan; Zhang, Yihe; Tian, Na

2015-01-01

Graphical abstract: The efficient charge transfer occurred at the interface of BiIO 4 /Bi 2 MoO 6 heterojunction results in the efficient separation of photoexcited electron–hole pairs and promotes the photocatalytic activity. - Highlights: • BiIO 4 /Bi 2 MoO 6 composites were synthesized by a one-step hydrothermal method. • The BiIO 4 /Bi 2 MoO 6 composite exhibits much better photoelectrochemical performance. • The highly improved photocatalytic activity is attributed to heterojunction structure. • Holes (h + ) are the main active species in the photodegradation process of RhB. - Abstract: A novel BiIO 4 /Bi 2 MoO 6 heterojunction photocatalyst has been successfully developed by a one-step hydrothermal method for the first time. It was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and diffuse reflection spectroscopy (DRS). Compared to pure BiIO 4 and Bi 2 MoO 6 , the BiIO 4 /Bi 2 MoO 6 composite exhibits the much better photoelectrochemical performance for Rhodamine B (RhB) degradation and photocurrent (PC) generation under visible light irradiation (λ > 420 nm). This enhancement on visible-light-responsive photocatalytic activity should be attributed to the fabrication of a BiIO 4 /Bi 2 MoO 6 heterojunction, thus resulting in the high separation and transfer efficiency of photogenerated charge carriers. The supposed photocatalytic mechanism dominated by holes (h + ) was verified by the photoluminescence (PL) spectroscopy, electrochemical impedance spectra (EIS) and active species trapping experiments

A facile fabrication of plasmonic g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag ternary heterojunction visible-light photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Dai, Kai, E-mail: daikai940@chnu.edu.cn [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China); Lv, Jiali [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China); Lu, Luhua, E-mail: lhlu@cug.edu.cn [Faculty of Material Science and Chemical Engineering, China University of Geosciences, Wuhan, 430074 (China); Liang, Changhao [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China); Key Laboratory of Materials Physics and Anhui Key Laboratory of Nanomaterials and Nanotechnology, Institute of Solid State Physics, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei, 230031 (China); Geng, Lei; Zhu, Guangping [College of Physics and Electronic Information, Huaibei Normal University, Huaibei, 235000 (China)

2016-07-01

It's important to reduce recombination of electrons and holes and enhance charge transfer through fine controlled interfacial structure. In this work, novel graphitic-C{sub 3}N{sub 4} (g-C{sub 3}N{sub 4})/Ag{sub 2}WO{sub 4}/Ag ternary photocatalyst has been synthesized by deposition of Ag{sub 2}WO{sub 4} onto g-C{sub 3}N{sub 4} template and followed by sun light reduction of Ag{sub 2}WO{sub 4} into Ag{sub 2}WO{sub 4}/Ag. As-prepared g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag presented significantly enhanced photocatalytic performance in degrading methylene blue (MB) under 410 nm LED light irradiation. Metallic Ag{sup 0} is used as plasmonic hot spots to generate high energy charge carriers. Optimal g-C{sub 3}N{sub 4} content has been confirmed to be 40 wt%, corresponding to apparent pseudo-first-order rate constant kapp of 0.0298 min{sup −1}, which is 3.3 times and 37.3 times more than that of pure g-C{sub 3}N{sub 4} and Ag{sub 2}WO{sub 4}, respectively. This novel ternary g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag structure material is an ideal candidate in environmental treatment and purifying applications. - Graphical abstract: A high efficient plasmonic graphitic-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag ternary nanocomposite photocatalyst was synthesized. - Highlights: • g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag ternary nanocomposite photocatalyst was prepared. • g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag showed high photocatalytic activity. • g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4}/Ag showed long reusable life.

Fabrication of BiOBr nanosheets@TiO{sub 2} nanobelts p–n junction photocatalysts for enhanced visible-light activity

Energy Technology Data Exchange (ETDEWEB)

Zhao, Yang [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Huang, Xiang [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); School of Science, Tibet University, Lhasa 850000 (China); Tan, Xin [School of Science, Tibet University, Lhasa 850000 (China); Yu, Tao, E-mail: yutao@tju.edu.cn [School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 (China); Collaborative Innovation Center of Chemical Science and Engineering (Tianjin), Tianjin 300072 (China); Li, Xiangli [School of Environmental Science and Engineering, Tianjin University, Tianjin 300072 (China); Yang, Libin [College of Chemical Engineering and Materials Science, Tianjin University of Science & Technology, Tianjin Key Laboratory of Marine Resources and Chemistry, Tianjin 300457 (China); Wang, Shucong [School of Environmental Science and Engineering, Tianjin University, Tianjin 300072 (China)

2016-03-01

Graphical abstract: - Highlights: • BiOBr nanosheets@TiO{sub 2} nanobelts p–n junction photocatalysts have been synthesized. • The p–n junction photocatalysts improved water splitting and dye degradation activity. • BiOBr amount in the BiOBr@TiO{sub 2} photocatalysts was investigated. - Abstract: The construction of p–n junction structure is a smart strategy for improving the photocatalytic activity, since p–n junctions can inhibit the recombination of photo-induced charges. Herein, BiOBr nanosheets@TiO{sub 2} nanobelts p–n junction photocatalysts were prepared by assembling BiOBr nanosheets on the surface of TiO{sub 2} nanobelts via a hydrothermal route followed by a co-precipitation process. BiOBr@TiO{sub 2} p–n junction photocatalysts exhibited enhanced photocatalytic activity in photocatalytic H{sub 2} production over water splitting and photodegradation of Rhodamine B (RhB) under visible light irradiation. Mott–Schottky plots confirmed the formation of p–n junctions in the interface of BiOBr and TiO{sub 2}. The enhanced photocatalytic performance can be ascribed to the 1D nanostructure and the formation of p–n junctions. This work shows a potential application of low cost BiOBr as a substitute for noble metals in photocatalytic H{sub 2} production under visible light irradiation.

Fabrication and photocatalytic activity enhanced mechanism of direct Z-scheme g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4} photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Zhu, Bicheng [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Department of Science and Environmental Studies The Hong Kong Institute of Education, Tai Po, N.T., Hong Kong (China); Xia, Pengfei; Li, Yao [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Ho, Wingkei, E-mail: keithho@ied.edu.hk [Department of Science and Environmental Studies The Hong Kong Institute of Education, Tai Po, N.T., Hong Kong (China); Yu, Jiaguo, E-mail: jiaguoyu@yahoo.com [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Department of Physics, Faculty of Science, King Abdulaziz University, Jeddah 21589 (Saudi Arabia)

2017-01-01

Highlights: • g-C{sub 3}N{sub 4} acted as a support for the in situ growth of β-Ag{sub 2}WO{sub 4}. • g-C{sub 3}N{sub 4} nanosheets inhibited the phase transformation of β-Ag{sub 2}WO{sub 4} to α-Ag{sub 2}WO{sub 4}. • g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4} exhibited a superior photocatalytic activity. • A direct Z-scheme photocatalytic mechanism could explain activity enhancement. - Abstract: Herein, a direct Z-scheme graphitic carbon nitride (g-C{sub 3}N{sub 4})/silver tungstate (Ag{sub 2}WO{sub 4}) photocatalyst was prepared by a facile in situ precipitation method using g-C{sub 3}N{sub 4} as a support and silver nitrate as a precursor. X-ray diffraction, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, transmission electron microscopy, and elemental mapping demonstrated that β-Ag{sub 2}WO{sub 4} nanoparticles were evenly distributed on the surface of g-C{sub 3}N{sub 4} nanosheets, which acted as a support for the nucleation and growth of β-Ag{sub 2}WO{sub 4} and inhibited the phase transformation of metastable β-Ag{sub 2}WO{sub 4} to stable α-Ag{sub 2}WO{sub 4}. Photocatalytic experiments indicated that the g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4} nanocomposite photocatalyst displayed a better photocatalytic activity than pure g-C{sub 3}N{sub 4} and Ag{sub 2}WO{sub 4} toward the degradation of methyl orange. The enhanced photocatalytic performance of g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4} could be well explained by a direct Z-scheme photocatalytic mechanism. This mechanism was related to the efficient space separation of photogenerated electron–hole pairs and the great oxidation and reduction capabilities of the g-C{sub 3}N{sub 4}/Ag{sub 2}WO{sub 4} system. This work provided new insights into the design and fabrication of g-C{sub 3}N{sub 4}-based direct Z-scheme photocatalysts.

Facile fabrication of Bi_2S_3/SnS_2 heterojunction photocatalysts with efficient photocatalytic activity under visible light

International Nuclear Information System (INIS)

Gao, Xiaomin; Huang, Guanbo; Gao, Haihuan; Pan, Cheng; Wang, Huan; Yan, Jing; Liu, Yu; Qiu, Haixia; Ma, Ning; Gao, Jianping

2016-01-01

In this work, Bi_2S_3/SnS_2 heterojunction photocatalysts were prepared by combining a hydrothermal technique and a facile in situ growth method. The nanocomposites were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, inductively coupled plasma spectroscopy, X-ray photoelectron spectroscopy, UV–Vis diffusion reflectance spectroscopy and room-temperature photoluminescence spectra. Their photocatalytic performances were evaluated by degrading methyl orange (MO) in aqueous solution (50 mg/L) under visible light (λ > 420 nm) irradiation. It was found that when the mass percentage of Bi_2S_3 in Bi_2S_3/SnS_2 was 7.95 wt%, the as-prepared Bi_2S_3/SnS_2 nanocomposite showed the best photocatalytic activity for the degradation of MO. The highly improved performance of the Bi_2S_3/SnS_2 nanocomposite was mainly ascribed to the efficient charge separation. - Highlights: • Facile fabrication of novel Bi_2S_3/SnS_2 heterojunction photocatalysts. • High-performance photocatalyst for the degradation of organic pollutants. • Good recyclability of catalyst without photo-corrosion. • The photocatalytic mechanism was proposed.

Role of indium tin oxide electrode on the microstructure of self-assembled WO3-BiVO4 hetero nanostructures

Science.gov (United States)

Song, Haili; Li, Chao; Van, Chien Nguyen; Dong, Wenxia; Qi, Ruijuan; Zhang, Yuanyuan; Huang, Rong; Chu, Ying-Hao; Duan, Chun-Gang

2017-11-01

Self-assembled WO3-BiVO4 nanostructured thin films were grown on a (001) yttrium stabilized zirconia (YSZ) substrate by the pulsed laser deposition method with and without the indium tin oxide (ITO) bottom electrode. Their microstructures including surface morphologies, crystalline phases, epitaxial relationships, interface structures, and composition distributions were investigated by scanning electron microscopy, high-resolution transmission electron microscopy, and X-ray energy dispersive spectroscopy. In both samples, WO3 formed nanopillars embedded into the monoclinic BiVO4 matrix with specific orientation relationships. In the sample with the ITO bottom electrode, an atomically sharp BiVO4/ITO interface was formed and the orthorhombic WO3 nanopillars were grown on a relaxed BiVO4 buffer layer with a mixed orthorhombic and hexagonal WO3 transition layer. In contrast, a thin amorphous layer appears at the interfaces between the thin film and the YSZ substrate in the sample without the ITO electrode. In addition, orthorhombic Bi2WO6 lamellar nanopillars were formed between WO3 and BiVO4 due to interdiffusion. Such a WO3-Bi2WO6-BiVO4 double heterojunction photoanode may promote the photo-generated charge separation and further improve the photoelectrochemical water splitting properties.

Fabrication of heterostructured Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 2}O{sub 4} photocatalyst and efficient photodegradation of organic contaminants under visible-light

Energy Technology Data Exchange (ETDEWEB)

Sun, Meng; Li, Shuangli; Yan, Tao; Ji, Pengge; Zhao, Xia; Yuan, Kun; Wei, Dong [School of Resources and Environment, University of Jinan, Jinan 250022 (China); Du, Bin, E-mail: dubin61@gmail.com [School of Resources and Environment, University of Jinan, Jinan 250022 (China); Key Laboratory of Chemical Sensing & Analysis in Universities of Shandong, School of Chemistry and Chemical Engineering, University of Jinan, Jinan 250022 (China)

2017-07-05

Highlights: • The product shows efficient activity in photodegradation of RhB, BPA, and phenol. • The BBOC-10 heterojunction exhibits the best activity under visible light. • Suppressed recombination of photo-generated carriers lead to the activity enhancement. - Abstract: Heterostructured Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 2}O{sub 4} photocatalysts were fabricated by a facile one-pot hydrothermal method, in which melem served as the sacrificial reagent to supply carbonate anions. The as-synthesized Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 2}O{sub 4} heterojunction catalysts were characterized by X-ray diffraction, UV–vis diffuse reflectance spectra, X-ray photoelectron spectroscopy, scanning electron microscope, and transmission electron microscope. The XRD patterns of Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 2}O{sub 4} catalysts showed the distinctive peaks of Bi{sub 2}O{sub 2}CO{sub 3} and Bi{sub 2}O{sub 4}. The SEM and TEM results showed that the pure Bi{sub 2}O{sub 2}CO{sub 3} possessed large plate morphology, while Bi{sub 2}O{sub 4} were composed of various nanorods and particles. As for Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 2}O{sub 4} heterojunction, it was obviously observed that Bi{sub 2}O{sub 4} nanorods and particles were grown on the surfaces of Bi{sub 2}O{sub 2}CO{sub 3} plates. The visible light driven photocatalytic activity of Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 2}O{sub 4} heterojunction photocatalyst was evaluated by decomposing dyes, phenol, and bisphenol A in water. Compared with Bi{sub 2}O{sub 2}CO{sub 3} and Bi{sub 2}O{sub 4}, the Bi{sub 2}O{sub 2}CO{sub 3}/Bi{sub 2}O{sub 4} photocatalysts have exhibited remarkable enhanced activity under visible light. The excellent activity can be mainly attributed to the enhanced separation efficiency of photo-generated carriers. Controlled experiments using different radical scavengers proved that ·O{sub 2}{sup −} and h{sup +} played the main role in decomposing organic pollutants. The results of this work would

NaYF4:Er,Yb/Bi2MoO6 core/shell nanocomposite: A highly efficient visible-light-driven photocatalyst utilizing upconversion

International Nuclear Information System (INIS)

Sun, Yuanyuan; Wang, Wenzhong; Sun, Songmei; Zhang, Ling

2014-01-01

Highlights: • Design and synthesis of NaYF 4 :Er,Yb/Bi 2 MoO 6 based on upconversion. • NaYF 4 :Er,Yb/Bi 2 MoO 6 nanocomposite was prepared for the first time. • Core–shell structure benefits the properties. • Upconversion contributed to the enhanced photocatalytic activity. • Helps to understand the functionality of new type photocatalysts. - Abstract: NaYF 4 :Er,Yb/Bi 2 MoO 6 core/shell nanocomposite was designed and prepared for the first time based on upconversion. The products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high resolution TEM (HRTEM), energy dispersive X-ray spectroscopy (EDS) and diffuse reflectance spectra (DRS). The results revealed that the as-synthesized NaYF 4 :Er,Yb/Bi 2 MoO 6 consisted of spheres with a core diameter of about 26 nm and a shell diameter of around 6 nm. The core was upconversion illuminant NaYF 4 :Er,Yb and the shell was Bi 2 MoO 6 around the core, which was confirmed by EDS. The NaYF 4 :Er,Yb/Bi 2 MoO 6 exhibited higher photocatalytic activity for the photodecomposition of Rhodamine B (RhB) under the irradiation of Xe lamp and green light emitting diode (g-LED). The mechanism of the high photocatalytic activity was discussed by photoluminescence spectra (PL), which is mainly attributed to upconversion of NaYF 4 :Er,Yb in the NaYF 4 :Er,Yb/Bi 2 MoO 6 nanocomposite and the core–shell structure

Photocatalytic Degradation of Methyl Orange on Bi2O3 and Ag2O-Bi2O3 Nano Photocatalysts

Directory of Open Access Journals (Sweden)

Seyed Ali Hosseini

2017-04-01

Full Text Available The photocatalytic activity of Bi2O3 and Ag2O-Bi2O3 was evaluated by degradation of aqueous methyl orange as a model dye effluent. Bi2O3 was synthesized using chemical precipitation method. Structural analysis revealed that Bi2O3 contain a unique well-crystallized phase and the average crystallite size of 22.4 nm. The SEM analysis showed that the size of Bi2O3 particles was mainly in the range of 16-22 nm. The most important variables affecting the photocatalytic degradation of dyes, namely reaction time, initial pH and catalyst dosage were studied, and their optimal amounts were found at 60 min, 5.58 and 0.025 g, respectively. A good correlation was found between experimental and predicted responses, confirming the reliability of the model. Incorporation of Ag2O in the structure of composite caused decreasing band gap and its response to visible light. Because a high percentage of sunlight is visible light, hence Ag2O-Bi2O3 nano-composite could be used as an efficient visible light driven photocatalyst for degradation of dye effluents by sunlight. Copyright © 2017 BCREC GROUP. All rights reserved Received: 15th August 2016; Revised: 20th December 2016; Accepted: 21st December 2016 How to Cite: Hosseini, S.A., Saeedi, R. (2017. Photocatalytic Degradation of Methyl Orange on Bi2O3 and Ag2O-Bi2O3 Nano Photocatalysts. Bulletin of Chemical Reaction Engineering & Catalysis, 12 (1: 96-105 (doi:10.9767/bcrec.12.1.623.96-105 Permalink/DOI: http://dx.doi.org/10.9767/bcrec.12.1.623.96-105

Comparison of modification strategies towards enhanced charge carrier separation and photocatalytic degradation activity of metal oxide semiconductors (TiO2, WO3 and ZnO)

Science.gov (United States)

Kumar, S. Girish; Rao, K. S. R. Koteswara

2017-01-01

Metal oxide semiconductors (TiO2, WO3 and ZnO) finds unparalleled opportunity in wastewater purification under UV/visible light, largely encouraged by their divergent admirable features like stability, non-toxicity, ease of preparation, suitable band edge positions and facile generation of active oxygen species in the aqueous medium. However, the perennial failings of these photocatalysts emanates from the stumbling blocks like rapid charge carrier recombination and meager visible light response. In this review, tailoring the surface-bulk electronic structure through the calibrated and veritable approaches such as impurity doping, deposition with noble metals, sensitizing with other compounds (dyes, polymers, inorganic complexes and simple chelating ligands), hydrogenation process (annealing under hydrogen atmosphere), electronic integration with other semiconductors, modifying with carbon nanostructures, designing with exposed facets and tailoring with hierarchical morphologies to overcome their critical drawbacks are summarized. Taking into account the materials intrinsic properties, the pros and cons together with similarities and striking differences for each strategy in specific to TiO2, WO3 & ZnO are highlighted. These subtlety enunciates the primacy for improving the structure-electronic properties of metal oxides and credence to its fore in the practical applications. Future research must focus on comparing the performances of ZnO, TiO2 and WO3 in parallel to get insight into their photocatalytic behaviors. Such comparisons not only reveal the changed surface-electronic structure upon various modifications, but also shed light on charge carrier dynamics, free radical generation, structural stability and compatibility for photocatalytic reactions. It is envisioned that these cardinal tactics have profound implications and can be replicated to other semiconductor photocatalysts like CeO2, In2O3, Bi2O3, Fe2O3, BiVO4, AgX, BiOX (X = Cl, Br & I), Bi2WO6, Bi2MoO6

1D Bi2S3 nanorod/2D e-WS2 nanosheet heterojunction photocatalyst for enhanced photocatalytic activity

Science.gov (United States)

Vattikuti, S. V. Prabhakar; Shim, Jaesool; Byon, Chan

2018-02-01

The development of high-activity, long-life, precious-metal-free photocatalysts for redox reactions in photoelectrochemical cells and fuel cells remains challenging. The synthesis of high-activity heterostructured photocatalysts is crucial for efficient energy conversion strategies. Herein, a novel photocatalyst based on 1D Bi2S3 nanorods self-assembled on 2D exfoliated tungsten disulfide (e-WS2) nanosheets has been developed for the degradation of methyl orange (MO) dye in aqueous solution. We demonstrate a novel and facile hydrothermal method for the synthesis of a Bi2S3 nanorod/e-WS2 nanosheet heterostructure. The photocatalytic properties of the heterostructure under visible light were investigated. Enhanced photocatalytic activity was attributed to the presence of strong surface active sites, as well as the specific morphology of the composite. We also observed the fast transfer of electron-hole pairs at the material interface. This work demonstrates a non-noble semiconductor photocatalyst for the degradation of pollutants and evolution of H2.

Solar photocatalytic activity of TiO2 modified with WO3 on the degradation of an organophosphorus pesticide

International Nuclear Information System (INIS)

Ramos-Delgado, N.A.; Gracia-Pinilla, M.A.; Maya-Treviño, L.; Hinojosa-Reyes, L.; Guzman-Mar, J.L.; Hernández-Ramírez, A.

2013-01-01

Highlights: • TiO 2 and WO 3 /TiO 2 (2 and 5%) were tested in the photocatalytic malathion degradation. • The use of solar radiation in the photocatalytic degradation process was evaluated. • Modified catalyst showed greater photocatalytic activity than pure TiO 2 . • The mineralization rate was improved when WO 3 content on TiO 2 was 2%. -- Abstract: In this study, the solar photocatalytic activity (SPA) of WO 3 /TiO 2 photocatalysts synthesized by the sol–gel method with two different percentages of WO 3 (2 and 5%wt) was evaluated using malathion as a model contaminant. For comparative purpose bare TiO 2 was also prepared by sol–gel process. The powders were characterized by X-ray diffraction (XRD), Raman spectroscopy, diffuse reflectance UV–vis spectroscopy (DRUV–vis), specific surface area by the BET method (SSA BET ), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and scanning transmission electron microscopy with a high annular angle dark field detector (STEM-HAADF). The XRD, Raman, HRTEM and STEM-HAADF analyses indicated that WO 3 was present as a monoclinic crystalline phase with nanometric cluster sizes (1.1 ± 0.1 nm for 2% WO 3 /TiO 2 and 1.35 ± 0.3 nm for 5% WO 3 /TiO 2 ) and uniformly dispersed on the surface of TiO 2 . The particle size of the materials was 19.4 ± 3.3 nm and 25.6 ± 3 nm for 2% and 5% WO 3 /TiO 2 , respectively. The SPA was evaluated on the degradation of commercial malathion pesticide using natural solar light. The 2% WO 3 /TiO 2 photocatalyst exhibited the best photocatalytic activity achieving 76% of total organic carbon (TOC) abatement after 300 min compared to the 5% WO 3 /TiO 2 and bare TiO 2 photocatalysts, which achieved 28 and 47% mineralization, respectively. Finally, experiments were performed to assess 2% WO 3 /TiO 2 catalyst activity on repeated uses; after several successive cycles its photocatalytic activity was retained showing long-term stability

Narrow band gap and visible light-driven photocatalysis of V-doped Bi{sub 6}Mo{sub 2}O{sub 15} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Xu, Jian; Qin, Chuanxiang; Huang, Yanlin [State and Local Joint Engineering Laboratory for Novel Functional Polymeric Materials, College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou 215123 (China); Wang, Yaorong, E-mail: yrwang@suda.edu.cn [State and Local Joint Engineering Laboratory for Novel Functional Polymeric Materials, College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou 215123 (China); Qin, Lin [Department of Physics and Interdisciplinary Program of Biomedical, Mechanical & Electrical Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of); Seo, Hyo Jin, E-mail: hjseo@pknu.ac.kr [Department of Physics and Interdisciplinary Program of Biomedical, Mechanical & Electrical Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of)

2017-02-28

Highlights: • V{sup 5+}-doped Bi{sub 6}Mo{sub 2}O{sub 15} was synthesized by the electrospinning preparation. • The band gap energy of Bi{sub 6}Mo{sub 2}O{sub 15} was greatly reduced by V-doping in the lattices. • V-doped Bi{sub 6}Mo{sub 2}O{sub 15} shows high activity in RhB degradation under visible light. • Crystal structure of Bi{sub 6}Mo{sub 2}O{sub 15} is favorable for high photocatalytic capacity. - Abstract: Pure and V{sup 5+}-doped Bi{sub 6}Mo{sub 2}O{sub 15} (3Bi{sub 2}O{sub 3}·2MoO{sub 3}) photocatalysts were synthesized through electrospinning, followed by low-temperature heat treatment. The samples developed into nanoparticles with an average size of approximately 50 nm. The crystalline phases were verified via X-ray powder diffraction measurements (XRD). The surface properties of the photocatalysts were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) analyses. The UV–vis spectra showed that V doping in Bi{sub 6}Mo{sub 2}O{sub 15} shifted the optical absorption from the UV region to the visible-light wavelength region. The energy of the band gap of Bi{sub 6}Mo{sub 2}O{sub 15} was reduced by V doping in the lattices. The photocatalytic activities of the pure and V-doped Bi{sub 6}Mo{sub 2}O{sub 15} were tested through photodegradation of rhodamine B (RhB) dye solutions under visible light irradiation. Results showed that 20 mol% V-doped Bi{sub 6}Mo{sub 2}O{sub 15} achieved efficient photocatalytic ability. RhB could be degraded by V-doped Bi{sub 6}Mo{sub 2}O{sub 15} in 2 h. The photocatalytic activities and mechanisms were discussed according to the characteristics of the crystal structure and the results of EIS and XPS measurements.

In situ synthesis of Bi2S3 sensitized WO3 nanoplate arrays with less interfacial defects and enhanced photoelectrochemical performance

Science.gov (United States)

Liu, Canjun; Yang, Yahui; Li, Wenzhang; Li, Jie; Li, Yaomin; Chen, Qiyuan

2016-03-01

In this study, Bi2S3 sensitive layer has been grown on the surface of WO3 nanoplate arrays via an in situ approach. The characterization of samples were carried out using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and ultraviolet-visible absorption spectroscopy (UV-vis). The results show that the Bi2S3 layer is uniformly formed on the surface of WO3 nanoplates and less interfacial defects were observed in the interface between the Bi2S3 and WO3. More importantly, the Bi2S3/WO3 films as photoanodes for photoelectrochemical (PEC) cells display the enhanced PEC performance compared with the Bi2S3/WO3 films prepared by a sequential ionic layer adsorption reaction (SILAR) method. In order to understand the reason for the enhanced PEC properties, the electron transport properties of the photoelectrodes were studied by using the transient photocurrent spectroscopy and intensity modulated photocurrent spectroscopy (IMPS). The Bi2S3/WO3 films prepared via an in situ approach have a greater transient time constant and higher electron transit rate. This is most likely due to less interfacial defects for the Bi2S3/WO3 films prepared via an in situ approach, resulting in a lower resistance and faster carrier transport in the interface between WO3 and Bi2S3.

Oxidative degradation of salicylic acid by sprayed WO{sub 3} photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Mohite, S.V.; Rajpure, K.Y., E-mail: rajpure@yahoo.com

2015-10-15

Highlights: • The photoactivity of sprayed WO{sub 3} thin film. • Photoelectrocatalytic degradation of salicylic acid. • Reaction kinetics and mineralization of pollutants by COD. - Abstract: The WO{sub 3} thin films were deposited using spray pyrolysis technique. The prepared WO{sub 3} thin films were characterized using photoelectrochemical (PEC), X-ray diffraction, atomic force microscopy (AFM), and UV–vis absorbance spectroscopy techniques. PEC measurements of WO{sub 3} films deposited at different deposition temperatures were carried out to study photoresponse. The maximum photocurrent (I{sub ph} = 261 μA/cm{sup 2}) was observed for the film deposited at the 225 °C. The monoclinic crystal structure of WO{sub 3} has been confirmed from X-ray diffraction studies. AFM studies were used to calculate particle size and average roughness of the films. Optical absorbance was studied to estimate the bandgap energy of WO{sub 3} thin film which was about 2.65 eV. The photoelectrocatalytic activity of WO{sub 3} film was studied by degradation of salicylic acid with reducing concentrations as function of reaction time. The WO{sub 3} photocatalyst degraded salicylic acid to about 67.14% with significant reduction in chemical oxygen demand (COD) value.

Synthesis of AgI/Bi2MoO6 nano-heterostructure with enhanced visible-light photocatalytic property

Directory of Open Access Journals (Sweden)

Li Zhang

2018-04-01

Full Text Available A novel nano-heterostructure of AgI/Bi2MoO6 photocatalyst was successfully synthesized via a facile deposition-precipitation method. The samples were systematically characterized by X-ray diffraction, scanning and transmission electron microscopy, X-ray photoemission spectroscopy, UV–Vis absorption spectroscopy, and photoluminescence spectra. While sole Bi2MoO6 or AgI showed poor activity toward photocatalytic rhodamine B degradation, the nano-heterostructure was found with superior performance. The AgI/Bi2MoO6 composite with an optimal content of 20 wt% AgI exhibited the highest photocatalytic degradation rate. Rhodamine B was totally degraded within 75 min visible-light irradiation. Moreover, the hybrid photocatalyst also showed a fairly good stability for several-cycle reuse. This study indicates that the AgI/Bi2MoO6 nano-heterostructure can be used as an effective candidate for photocatalytic degradation of organic pollutants. Keywords: Heterostructure, Photocatalyst, RhB-degradation

Fabrication of a direct Z-scheme type WO{sub 3}/Ag{sub 3}PO{sub 4} composite photocatalyst with enhanced visible-light photocatalytic performances

Energy Technology Data Exchange (ETDEWEB)

Lu, Jinsuo, E-mail: lujinsuo@xauat.edu.cn [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Wang, Yujing [School of Materials and Chemical Engineering, Xi’an Technological University, Xi’an, Shaanxi 710032 (China); Liu, Fei [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Zhang, Liang [College of Sciences, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Chai, Shouning, E-mail: s.n.chai@xauat.edu.cn [College of Sciences, Xi’an University of Architecture and Technology, Xi’an 710055 (China)

2017-01-30

Highlights: • A solid direct Z-scheme type photocatalyst WO{sub 3}/Ag{sub 3}PO{sub 4} was synthesized. • The WO{sub 3}/Ag{sub 3}PO{sub 4} composite showed enhanced photocatalytic activity and stability. • Nearly complete removal of organic dyes was achieved in a short time. • The reasonable Z-scheme mechanism of WO{sub 3}/Ag{sub 3}PO{sub 4} composite was proposed. - Abstract: A direct Z-scheme type photocatalyst WO{sub 3}/Ag{sub 3}PO{sub 4} composite (molar ration 1:1, 1W/1Ag) was prepared by hydrothermal method. The 1W/1Ag was characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), UV–vis diffuse reflection spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS), and photoluminescence emission spectroscopy (PL) etc. technologies. The photocatalytic performances were evaluated by degradation of methylene blue (MB) and methyl orange (MO), and their removal rates were up to 95% after 60 min and 90% after 180 min, respectively. The prepared 1W/1Ag exhibits a much higher photocatalytic activity than pure Ag{sub 3}PO{sub 4} and pure WO{sub 3} under visible light irradiation. The apparent rate constants of MB and MO degradation on 1W/1Ag are about 2.4 and 2.5 times that of pure Ag{sub 3}PO{sub 4}, respectively. The enhanced performance of the 1W/1Ag is attributed to a synergistic effect including relatively high surface area, strong light absorption, matched energy band structure, and the improved separation of photogenerated charge carriers between the two components. A reasonable Z-scheme mechanism referring to directed migration of photoinduced carriers was proposed. Thus, it can be suggested that the 1W/1Ag can serve as a promising photocatalyst for environmental purification and clean energy utilization.

Preparation and property of magnetic photocatalyst BiOCl/Mn{sub x}Zn{sub 1−x}Fe{sub 2}O{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Feng, Shan; Xu, Longjun, E-mail: xulj@cqu.edu.cn; Liu, Chenglun [State Key Laboratory of Coal Mine Disaster Dynamics and Control (China); Du, Haigang [Liupanshui Normal University, Department of Mining Engineering (China); Xie, Taiping [State Key Laboratory of Coal Mine Disaster Dynamics and Control (China); Zhu, Qianqian [Chongqing University, College of Chemistry and Chemical Engineering (China)

2017-02-15

The magnetic photocatalyst BiOCl/Mn{sub x}Zn{sub 1−x}Fe{sub 2}O{sub 4} was prepared by impregnation-calcination method. The structure and properties of the prepared photocatalyst were characterized by FTIR, XRD, SEM, TEM, UV–vis DRS, and VSM. Mn{sub x}Zn{sub 1−x}Fe{sub 2}O{sub 4} inhibited the growth along (001) crystal face and promoted (110) crystal surface exposure of BiOCl. The as-prepared magnetic composite appeared flower-like microspheres assembled with nanosheets. The average crystallite size and the nanosheet thickness range of BiOCl/Mn{sub x}Zn{sub 1−x}Fe{sub 2}O{sub 4} were 57.6 and 75.7–112.2 nm, respectively. The band gap energy (E{sub g}) of BiOCl/Mn{sub x}Zn{sub 1−x}Fe{sub 2}O{sub 4} was 2.48 eV, which was lower than that of BiOCl. The saturation magnetization (Ms), coercive force (Hc), and remanent magnetization (Mr) of BiOCl/Mn{sub x}Zn{sub 1−x}Fe{sub 2}O{sub 4} were respectively 4.64 emu g{sup −1}, 50.12 G and 0.09 emu g{sup −1}, indicating a good resistance to demagnetization and paramagnetism. The optimum synthesis condition of BiOCl/Mn{sub x}Zn{sub 1−x}Fe{sub 2}O{sub 4} was obtained by orthogonal experiments, and the degradation ratio of RhB with the photocatalyst was 99.6% at 30 min. After four cycles, the degradation ratio of RhB with the recovered photocatalyst was still above 83%.

A P25/(NH4)xWO3 hybrid photocatalyst with broad spectrum photocatalytic properties under UV, visible, and near-infrared irradiation.

Science.gov (United States)

Yang, Linfen; Liu, Bin; Liu, Tongyao; Ma, Xinlong; Li, Hao; Yin, Shu; Sato, Tsugio; Wang, Yuhua

2017-04-03

In this study, a series of hybrid nanostructured photocatalysts P25/(NH 4 ) x WO 3 nanocomposites with the average crystallite size of P25 and (NH 4 ) x WO 3 of the sample was calculated to be about 30 nm and 130 nm, were successfully synthesized via a simple one-step hydrothermal method. The as-obtained samples was characterized by transmission electron microscopy (TEM), which implies that the P25/(NH 4 ) x WO 3 nanocomposites are fabricated with favourable nanosizd interfacial. The XPS results confirmed that the obtained sample consists of mixed chemical valences of W 5+ and W 6+ , the low-valance W 5+ sites could be the origin of NIR absorption. As revealed by optical absorption results, P25/(NH 4 ) x WO 3 nanocomposites possess high optical absorption in the whole solar spectrum of 200-2500 nm. Benefiting from this unique photo-absorption property and the synergistic effect of P25 and (NH 4 ) x WO 3 , broad spectrum response photocatalytic activities covering UV, visible and near infrared regions on degradation of Rhodamine B have been realized by P25/(NH 4 ) x WO 3 nanocomposites. Meanwhile, the stability of photocatalysts was examined by the XRD and XPS of the photocatalysts after the reaction. The results show that P25/(NH 4 ) x WO 3 photocatalysts has a brilliant application prospect in the energy utilization to solve deteriorating environmental issues.

Solar photocatalytic activity of TiO{sub 2} modified with WO{sub 3} on the degradation of an organophosphorus pesticide

Energy Technology Data Exchange (ETDEWEB)

Ramos-Delgado, N.A. [Universidad Autónoma de Nuevo León, Facultad de Ciencias Químicas, San Nicolás de los Garza, N.L. (Mexico); Gracia-Pinilla, M.A. [Universidad Autónoma de Nuevo León, Facultad de Ciencias Físico-Matemáticas, Av. Universidad, Cd. Universitaria, San Nicolás de los Garza, N.L. (Mexico); Universidad Autónoma de Nuevo León, Centro de Investigación e Innovación en Desarrollo de Ingeniería y Tecnología, PIIT Km 6, Carretera al Aeropuerto, Apodaca, N.L. (Mexico); Maya-Treviño, L.; Hinojosa-Reyes, L.; Guzman-Mar, J.L. [Universidad Autónoma de Nuevo León, Facultad de Ciencias Químicas, San Nicolás de los Garza, N.L. (Mexico); Hernández-Ramírez, A., E-mail: aracely.hernandezrm@uanl.edu.mx [Universidad Autónoma de Nuevo León, Facultad de Ciencias Químicas, San Nicolás de los Garza, N.L. (Mexico)

2013-12-15

Highlights: • TiO{sub 2} and WO{sub 3}/TiO{sub 2} (2 and 5%) were tested in the photocatalytic malathion degradation. • The use of solar radiation in the photocatalytic degradation process was evaluated. • Modified catalyst showed greater photocatalytic activity than pure TiO{sub 2}. • The mineralization rate was improved when WO{sub 3} content on TiO{sub 2} was 2%. -- Abstract: In this study, the solar photocatalytic activity (SPA) of WO{sub 3}/TiO{sub 2} photocatalysts synthesized by the sol–gel method with two different percentages of WO{sub 3} (2 and 5%wt) was evaluated using malathion as a model contaminant. For comparative purpose bare TiO{sub 2} was also prepared by sol–gel process. The powders were characterized by X-ray diffraction (XRD), Raman spectroscopy, diffuse reflectance UV–vis spectroscopy (DRUV–vis), specific surface area by the BET method (SSA{sub BET}), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and scanning transmission electron microscopy with a high annular angle dark field detector (STEM-HAADF). The XRD, Raman, HRTEM and STEM-HAADF analyses indicated that WO{sub 3} was present as a monoclinic crystalline phase with nanometric cluster sizes (1.1 ± 0.1 nm for 2% WO{sub 3}/TiO{sub 2} and 1.35 ± 0.3 nm for 5% WO{sub 3}/TiO{sub 2}) and uniformly dispersed on the surface of TiO{sub 2}. The particle size of the materials was 19.4 ± 3.3 nm and 25.6 ± 3 nm for 2% and 5% WO{sub 3}/TiO{sub 2}, respectively. The SPA was evaluated on the degradation of commercial malathion pesticide using natural solar light. The 2% WO{sub 3}/TiO{sub 2} photocatalyst exhibited the best photocatalytic activity achieving 76% of total organic carbon (TOC) abatement after 300 min compared to the 5% WO{sub 3}/TiO{sub 2} and bare TiO{sub 2} photocatalysts, which achieved 28 and 47% mineralization, respectively. Finally, experiments were performed to assess 2% WO{sub 3}/TiO{sub 2} catalyst activity on

Improvement of optical properties and radiation hardness of NaBi(WO sub 4) sub 2 Cherenkov crystals

CERN Document Server

Zadneprovski, B I; Polyansky, E V; Devitsin, E G; Kozlov, V A; Potashov, S Yu; Terkulov, A R

2002-01-01

On the basis of the data on melt evaporation while growing NaBi(WO sub 4) sub 2 Cherenkov crystals, the formation of nonstoichiometry and most probable types of dot defects of the crystals have been considered. The influence of melt nonstoichiometry and doping with Sc on optical transmission and radiation hardness of the crystals has been experimentally investigated. The surplus of WO sub 3 has been established to increase optical transmission and radiation hardness and lack of Bi sub 2 O sub 3 in the melt to reduce radiation hardness. Sc doping is shifting the absorption edge to UV region by 30-35 nm and is increasing radiation hardness of the crystals about three-fold. Analytical estimations give the increase of the number of Cherenkov photons by a factor of 1.3, which leads to an improvement of the energy resolution of a calorimeter based on NaBi(WO sub 4) sub 2 :Sc crystals compared with undoped NaBi(WO sub 4) sub 2 of approximately 15%.

Monoclinic α-Bi2O3 photocatalyst for efficient removal of gaseous NO and HCHO under visible light irradiation

International Nuclear Information System (INIS)

Ai Zhihui; Huang Yu; Lee Shuncheng; Zhang Lizhi

2011-01-01

Research highlights: → We got the monoclinic α-Bi 2 O 3 powders after the calcinations of the plate-like (BiO) 2 CO 3 precursors at 500 deg. C for 4 h. → The synthetic α-Bi 2 O 3 showed high visible light photocatalytic activity for removal of NO and HCHO. - Abstract: The investigation was focused on the visible-light-driven photocatalytic removal of gaseous NO and HCHO at typical indoor air concentration over synthetic α-Bi 2 O 3 . Monoclinic α-Bi 2 O 3 was synthesized via calcination of hydrothermally prepared (BiO) 2 CO 3 precursor at 500 deg. C for 4 h. The synthetic α-Bi 2 O 3 samples were systematically characterized by XRD, SEM, FT-IR, and UV-vis diffuse reflectance spectra (DRS). The optical band gap energy of the resulting α-Bi 2 O 3 was estimated to be 2.72 eV from the UV-vis absorption spectra. Comparing with the commercial Bi 2 O 3 counterpart, the fabricated α-Bi 2 O 3 showed superior visible-light-induced photocatalytic activity on degradation of nitrogen monoxide (NO) and formaldehyde (HCHO) at typical indoor air concentration. No obvious deactivation of synthetic α-Bi 2 O 3 was observed during the prolonged photocatalytic reaction. This work suggests that the synthesized monoclinic α-Bi 2 O 3 with suitable band gap and high activity is promising photocatalyst for indoor air purification.

Hydrothermal synthesis of CdS/Bi{sub 2}MoO{sub 6} heterojunction photocatalysts with excellent visible-light-driven photocatalytic performance

Energy Technology Data Exchange (ETDEWEB)

Feng, Yi; Yan, Xu; Liu, Chunbo; Hong, Yuanzhi; Zhu, Lin; Zhou, Mingjun; Shi, Weidong, E-mail: swd1978@ujs.edu.cn

2015-10-30

Graphical abstract: - Highlights: • The novel CdS/Bi{sub 2}MoO{sub 6} heterojunction were synthesized for the first time via a two-step hydrothermal process. • The CdS/Bi{sub 2}MoO{sub 6} heterojunction exhibited an excellent visible-light-driven photocatalytic activity for RhB degradation. • The photocatalytic activity of this heterojunction also evaluated by TC, MB degradation. • The mechanism of this photocatalysis system was firstly proposed. - Abstract: A novel CdS/Bi{sub 2}MoO{sub 6} heterojunction photocatalysts were successfully prepared via two-step hydrothermal methods. The prepared samples were characterized by various physicochemical techniques, such as XRD, SEM, TEM, HRTEM, XPS, UV–vis and PL. The obtained samples exhibited highly photocatalytic activity toward the degradation of the different kinds of organic dyes and tetracycline in aqueous solution under visible light irradiation (λ > 420 nm). The optimum photocatalytic efficiency of CdS-2 sample for the degradation rhodamine B (RhB) was about 25.3 and 3.7 times higher than that of individual CdS and Bi{sub 2}MoO{sub 6}, respectively. In addition, the possible photocatalytic mechanism was analyzed by different active species trapping experiments. The results indicated that the h{sup +} and ·O{sub 2}{sup −} were the main active species for the photocatalytic degradation of RhB. Moreover, the prepared sample shows good stability and recyclability properties which are beneficial for its practical application.

Optical temperature sensing by upconversion luminescence of Er doped Bi5TiNbWO15ferroelectric materials

Directory of Open Access Journals (Sweden)

Hua Zou

2014-12-01

Full Text Available The Er3+ doped Bi5TiNbWO15 ceramics have been synthesized using conventional solid-state reaction techniques. The crystal structure, ferroelectric properties, UC emission properties and especially the temperature sensing behaviors were systematically studied. With increasing Er3+ content, the investigation of XRD pattern, the ferroelectric loop and the UC emission indicated that the Er3+ ions dopants preferentially substituted the A sites of Bi3TiNbO9 and then Bi2WO6. Based on fluorescence intensity ratio (FIR technique, the observed results implied the ceramics were promising candidates for temperature sensors in the temperature range of 175 K −550 K. More importantly, this study provided a contrast of temperature sensitivity between emission from the same part (Bi3TiNbO9 in bismuth layered-structure and emission from the different part (Bi3TiNbO9 and Bi2WO6 in bismuth layered-structure for the first time.

Structure and photocatalytic performance of layered HNbWO6 nanosheet aggregation

KAUST Repository

Hu, Li-Fang

2015-12-10

Layered HNbWO6HNbWO6 nanosheet aggregation (e-HNbWO6e-HNbWO6) has been assembled by HNbWO6HNbWO6 nanosheet via an exfoliation-restaking route. The as-prepared samples are characterized by means of powder x-ray diffraction, scanning electron microscope, high-resolution transmission electron microscopy, laser Raman spectroscopy, ultraviolet-vis diffuse reflectance spectroscopy, and N2N2 adsorption-desorption isotherms. The photocatalytic performances of the as-prepared samples are evaluated by degradation of methylene blue (MB). The results revealed that e-HNbWO6e-HNbWO6 has a specific surface area of about 156.5  m2 g−1156.5  m2 g−1, and exhibits a relatively excellent photocatalytic performance for degradation of MB under UV light.

Structure and photocatalytic performance of layered HNbWO6 nanosheet aggregation

KAUST Repository

Hu, Li-Fang; Li, Rui; He, Jie; Da, Liang-guo; Lv, Wei; Hu, Jin-song

2015-01-01

Layered HNbWO6HNbWO6 nanosheet aggregation (e-HNbWO6e-HNbWO6) has been assembled by HNbWO6HNbWO6 nanosheet via an exfoliation-restaking route. The as-prepared samples are characterized by means of powder x-ray diffraction, scanning electron microscope, high-resolution transmission electron microscopy, laser Raman spectroscopy, ultraviolet-vis diffuse reflectance spectroscopy, and N2N2 adsorption-desorption isotherms. The photocatalytic performances of the as-prepared samples are evaluated by degradation of methylene blue (MB). The results revealed that e-HNbWO6e-HNbWO6 has a specific surface area of about 156.5  m2 g−1156.5  m2 g−1, and exhibits a relatively excellent photocatalytic performance for degradation of MB under UV light.

BiVO4 -TiO2 Composite Photocatalysts for Dye Degradation Formed Using the SILAR Method.

Science.gov (United States)

Odling, Gylen; Robertson, Neil

2016-09-19

Composite photocatalyst films have been fabricated by depositing BiVO4 upon TiO2 via a sequential ionic layer adsorption reaction (SILAR) method. The photocatalytic materials were investigated by XRD, TEM, UV/Vis diffuse reflectance, inductively coupled plasma optical emission spectrometry (ICP-OES), XPS, photoluminescence and Mott-Schottky analyses. SILAR processing was found to deposit monoclinic-scheelite BiVO4 nanoparticles onto the surface, giving successive improvements in the films' visible light harvesting. Electrochemical and valence band XPS studies revealed that the prepared heterojunctions have a type II band structure, with the BiVO4 conduction band and valence band lying cathodically shifted from those of TiO2 . The photocatalytic activity of the films was measured by the decolourisation of the dye rhodamine 6G using λ>400 nm visible light. It was found that five SILAR cycles was optimal, with a pseudo-first-order rate constant of 0.004 min(-1) . As a reference material, the same SILAR modification has been made to an inactive wide-band-gap ZrO2 film, where the mismatch of conduction and valence band energies disallows charge separation. The photocatalytic activity of the BiVO4 -ZrO2 system was found to be significantly reduced, highlighting the importance of charge separation across the interface. The mechanism of action of the photocatalysts has also been investigated, in particular the effect of self-sensitisation by the model organic dye and the ability of the dye to inject electrons into the photocatalyst's conduction band. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Facile synthesis of Z-scheme graphitic-C{sub 3}N{sub 4}/Bi{sub 2}MoO{sub 6} nanocomposite for enhanced visible photocatalytic properties

Energy Technology Data Exchange (ETDEWEB)

Lv, Jiali [College of Physics and Electronic Information, Huaibei Normal University, Huaibei 235000 (China); Dai, Kai, E-mail: daikai940@chnu.edu.cn [College of Physics and Electronic Information, Huaibei Normal University, Huaibei 235000 (China); Zhang, Jinfeng; Geng, Lei [College of Physics and Electronic Information, Huaibei Normal University, Huaibei 235000 (China); Liang, Changhao, E-mail: chliang@issp.ac.cn [College of Physics and Electronic Information, Huaibei Normal University, Huaibei 235000 (China); Key Laboratory of Materials Physics and Anhui Key Laboratory of Nanomaterials and Nanotechnology, Institute of Solid State Physics, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei 230031 (China); Liu, Qiangchun; Zhu, Guangping; Chen, Chen [College of Physics and Electronic Information, Huaibei Normal University, Huaibei 235000 (China)

2015-12-15

Graphical abstract: - Highlights: • g-C{sub 3}N{sub 4}/Bi{sub 2}MoO{sub 6} nanocomposite photocatalyst was prepared. • g-C{sub 3}N{sub 4}/Bi{sub 2}MoO{sub 6} as a typical Z-scheme photocatalyst was proved. • g-C{sub 3}N{sub 4}/Bi{sub 2}MoO{sub 6} showed long reusable life with irradiation of LED light. - Abstract: The band engineering of visible-light-driven photocatalysts is a promising route for harnessing of effective solar energy to perform high chemical reactions and to treat environmental pollution. In this study, two narrow band gap semiconductor nanomaterials, graphitic carbon nitride (g-C{sub 3}N{sub 4}) and Bi{sub 2}MoO{sub 6}, were selected and coupled to form series of g-C{sub 3}N{sub 4}/Bi{sub 2}MoO{sub 6} photocatalysts. Their structure, light absorption wavelength range, charge transport properties and energy level were investigated. Through perfect manipulation of their composition, enhanced photocatalytic activity of the Z-scheme g-C{sub 3}N{sub 4}/Bi{sub 2}MoO{sub 6} photocatalysts with efficient reduction of recombination of photogenerated electrons and holes was achieved. The optimized Z-scheme g-C{sub 3}N{sub 4}/Bi{sub 2}MoO{sub 6} photocatalysts with 25 wt%g-C{sub 3}N{sub 4} showed apparent pseudo-first-order rate constant k{sub app} as high as 0.0688 min{sup −1}, which was 4.8 times and 8.2 times higher than that of g-C{sub 3}N{sub 4} and Bi{sub 2}MoO{sub 6} photocatalyst, respectively.

Evidence of superoxide radical contribution to demineralization of sulfamethoxazole by visible-light-driven Bi{sub 2}O{sub 3}/Bi{sub 2}O{sub 2}CO{sub 3}/Sr{sub 6}Bi{sub 2}O{sub 9} photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Ding, Shiyuan; Niu, Junfeng, E-mail: junfengn@bnu.edu.cn; Bao, Yueping; Hu, Lijuan

2013-11-15

Highlights: • Bi{sub 2}O{sub 3}/Bi{sub 2}O{sub 2}CO{sub 3}/Sr{sub 6}Bi{sub 2}O{sub 9} can degrade SMX efficiently using visible light. • 36% of TOC reduction was achieved after 120 min treatment. • The main mineralization products were confirmed. • Formation of O{sub 2}·{sup −} was evidenced by using ESR and a chemiluminescent probe. -- Abstract: Photocatalytic degradation of sulfamethoxazole (SMX) was investigated using Bi{sub 2}O{sub 3}/Bi{sub 2}O{sub 2}CO{sub 3}/Sr{sub 6}Bi{sub 2}O{sub 9} (BSO) photocatalyst under visible light (>420 nm) irradiation. The photochemical degradation of SMX followed pseudo-first-order kinetics. The reaction kinetics was determined as a function of initial SMX concentrations (5–20 mg L{sup −1}), initial pH (3–11) and BSO concentrations (6–600 mg L{sup −1}). Approximately, 90% of SMX (10 mg L{sup −1}) degradation and 36% of TOC reduction were achieved at pH 7.0 after 120 min irradiation. The main mineralization products, including NH{sub 4}{sup +}, NO{sub 3}{sup −}, SO{sub 4}{sup 2−} and CO{sub 2}, as well as intermediates 3-amino-5-methylisoxazole (AMI), p-benzoquinone (BZQ), and sulfanilic acid (SNA) were detected in aqueous solution. The formation of O{sub 2}·{sup −} radical was evidenced by using electron spin resonance and a chemiluminescent probe, luminal. A possible degradation mechanism involving excitation of BSO, followed by charge injection into the BSO conduction band and formation of reactive superoxide radical (O{sub 2}·{sup −}) was proposed for the mineralization of SMX. During the reaction, the O{sub 2}·{sup −} radical attacks the sulfone moiety and causes the cleavage of the S-N bond, which leads to the formation of two sub-structure analogs, AMI and SNA.

Facile fabrication of Bi{sub 2}S{sub 3}/SnS{sub 2} heterojunction photocatalysts with efficient photocatalytic activity under visible light

Energy Technology Data Exchange (ETDEWEB)

Gao, Xiaomin; Huang, Guanbo [Department of Chemistry, School of Science, Tianjin University, Tianjin 300072 (China); Gao, Haihuan [Tianjin Fourth Middle School, Tianjin 300021 (China); Pan, Cheng; Wang, Huan [Department of Chemistry, School of Science, Tianjin University, Tianjin 300072 (China); Yan, Jing, E-mail: yanjingls2012@163.com [Department of Chemistry, School of Science, Tianjin University, Tianjin 300072 (China); Collaborative Innovation Center of Chemical Science and Engineering, Tianjin 300072 (China); Liu, Yu [Department of Chemistry, School of Science, Tianjin University, Tianjin 300072 (China); Qiu, Haixia [Department of Chemistry, School of Science, Tianjin University, Tianjin 300072 (China); Collaborative Innovation Center of Chemical Science and Engineering, Tianjin 300072 (China); Ma, Ning [Department of Chemistry, School of Science, Tianjin University, Tianjin 300072 (China); Gao, Jianping [Department of Chemistry, School of Science, Tianjin University, Tianjin 300072 (China); Collaborative Innovation Center of Chemical Science and Engineering, Tianjin 300072 (China)

2016-07-25

In this work, Bi{sub 2}S{sub 3}/SnS{sub 2} heterojunction photocatalysts were prepared by combining a hydrothermal technique and a facile in situ growth method. The nanocomposites were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, inductively coupled plasma spectroscopy, X-ray photoelectron spectroscopy, UV–Vis diffusion reflectance spectroscopy and room-temperature photoluminescence spectra. Their photocatalytic performances were evaluated by degrading methyl orange (MO) in aqueous solution (50 mg/L) under visible light (λ > 420 nm) irradiation. It was found that when the mass percentage of Bi{sub 2}S{sub 3} in Bi{sub 2}S{sub 3}/SnS{sub 2} was 7.95 wt%, the as-prepared Bi{sub 2}S{sub 3}/SnS{sub 2} nanocomposite showed the best photocatalytic activity for the degradation of MO. The highly improved performance of the Bi{sub 2}S{sub 3}/SnS{sub 2} nanocomposite was mainly ascribed to the efficient charge separation. - Highlights: • Facile fabrication of novel Bi{sub 2}S{sub 3}/SnS{sub 2} heterojunction photocatalysts. • High-performance photocatalyst for the degradation of organic pollutants. • Good recyclability of catalyst without photo-corrosion. • The photocatalytic mechanism was proposed.

Comparison of modification strategies towards enhanced charge carrier separation and photocatalytic degradation activity of metal oxide semiconductors (TiO{sub 2}, WO{sub 3} and ZnO)

Energy Technology Data Exchange (ETDEWEB)

Kumar, S. Girish [Department of Physics, Indian Institute of Science, Bengaluru, 560012 Karnataka (India); Department of Chemistry, School of Engineering and Technology, CMR University, Bengaluru, 562149, Karnataka (India); Rao, K.S.R. Koteswara, E-mail: raoksrk@gmail.com [Department of Physics, Indian Institute of Science, Bengaluru, 560012 Karnataka (India)

2017-01-01

the changed surface-electronic structure upon various modifications, but also shed light on charge carrier dynamics, free radical generation, structural stability and compatibility for photocatalytic reactions. It is envisioned that these cardinal tactics have profound implications and can be replicated to other semiconductor photocatalysts like CeO{sub 2}, In{sub 2}O{sub 3}, Bi{sub 2}O{sub 3}, Fe{sub 2}O{sub 3}, BiVO{sub 4}, AgX, BiOX (X = Cl, Br & I), Bi{sub 2}WO{sub 6}, Bi{sub 2}MoO{sub 6}, etc., to improve their competence for various environmental applications.

Enhanced photocatalytic activity of Bi{sub 2}O{sub 3}–Ag{sub 2}O hybrid photocatalysts

Energy Technology Data Exchange (ETDEWEB)

Liu, Xinjuan, E-mail: lxj669635@126.com [Institute of Coordination Bond Metrology and Engineering, College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China); Liu, Junying [Engineering Research Center for Nanophotonics & Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 China (China); Chu, Haipeng [Institute of Coordination Bond Metrology and Engineering, College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China); Li, Jinliang; Yu, Wei [Engineering Research Center for Nanophotonics & Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 China (China); Zhu, Guang [Anhui Key Laboratory of Spin Electron and Nanomaterials, Suzhou University, Suzhou 234000 (China); Niu, Lengyuan [Institute of Coordination Bond Metrology and Engineering, College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China); Sun, Zhuo [Engineering Research Center for Nanophotonics & Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 China (China); Pan, Likun, E-mail: lkpan@phy.ecnu.edu.cn [Engineering Research Center for Nanophotonics & Advanced Instrument, Ministry of Education, Department of Physics, East China Normal University, Shanghai 200062 China (China); Sun, Chang Q. [Institute of Coordination Bond Metrology and Engineering, College of Materials Science and Engineering, China Jiliang University, Hangzhou 310018 (China)

2015-08-30

Graphical abstract: Bi{sub 2}O{sub 3}–Ag{sub 2}O composites were fabricated for visible light photocatalytic degradation of phenol with a high degradation rate of 92% for 60 min. - Highlights: • Bi{sub 2}O{sub 3}–Ag{sub 2}O composites were synthesized via a co-precipitation method. • The photocatalytic activity for the degradation of phenol is investigated. • A high degradation rate of 92% for 60 min is achieved under visible light irradiation. - Abstract: Bi{sub 2}O{sub 3}–Ag{sub 2}O hybrid photocatalysts were successfully synthesized via a co-precipitation method. The morphology, structure and photocatalytic performance in the degradation of phenol were characterized by using scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, electrochemical impedance spectra and UV–vis absorption spectroscopy, respectively. The results show that Bi{sub 2}O{sub 3}–Ag{sub 2}O hybrid photocatalysts exhibit enhanced photocatalytic performance in the degradation of phenol with a maximum degradation rate of 92% for 60 min under visible light irradiation compared with pure Bi{sub 2}O{sub 3} (57%), which is ascribed to the increase in light adsorption and the reduction in electron–hole pair recombination with the introduction of Ag{sub 2}O.

Graphene and TiO_2 co-modified flower-like Bi_2O_2CO_3: A novel multi-heterojunction photocatalyst with enhanced photocatalytic activity

International Nuclear Information System (INIS)

Ao, Yanhui; Xu, Liya; Wang, Peifang; Wang, Chao; Hou, Jun; Qian, Jin; Li, Yi

2015-01-01

Graphical abstract: A novel multi-heterojunction photocatalyst (graphene and TiO_2 co-modified flower-like Bi_2O_2CO_3) was prepared for the first time. The as-obtained samples showed much higher activity compared to pure Bi_2O_2CO_3, TiO_2 and GR–Bi_2O_2CO_3 for dye degradation, which is almost 14 times higher than that of pure Bi_2O_2CO_3 and also much higher than the sum of graphene–Bi_2O_2CO_3 and TiO_2. - Highlights: • Graphene and TiO_2 co-modified flower-like Bi_2O_2CO_3 was prepared for the first time. • The sample shows enhanced photocatalytic activity due to the formation of multi-heterojunction. • The sample also exhibits a synergetic effect of graphene and TiO_2. • The composite photocatalyst shows a good stability for dye degradation. - Abstract: In this paper, graphene (GR) and titania co-modified flower-like Bi_2O_2CO_3 multi-heterojunction composite photocatalysts were prepared by a simple and feasible two step hydrothermal process. The prepared samples were analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectrometry (DRS), photoluminescence (PL), N_2 adsorption–desorption isotherm, and photo-induced current. The photocatalytic activity was investigated by the degradation of MO under UV light irradiation. The as prepared multi-heterojunction GR/Bi_2O_2CO_3/TiO_2 composites exhibited much higher photocatalytic activity than pure Bi_2O_2CO_3, TiO_2 and GR–Bi_2O_2CO_3. The higher performance of GR/Bi_2O_2CO_3/TiO_2 can be ascribed to the formation of multi-heterojunctions, which promote the effective separation of photo-induced electron–hole pairs. Moreover, the higher photocatalytic activity can also be ascribed to the high surface area of GR and TiO_2, which offers more active sites for the photodegradation reaction. Furthermore, the photocatalytic activity of GR/Bi_2O_2CO_3/TiO_2 remained without striking decrease after five cycles

Photocatalytic properties of h-WO{sub 3} nanoparticles obtained by annealing and h-WO{sub 3} nanorods prepared by hydrothermal method

Energy Technology Data Exchange (ETDEWEB)

Boyadjiev, Stefan I., E-mail: boiajiev@gmail.com [MTA-BME Technical Analytical Chemistry Research Group, Szent Gellért tér 4, Budapest, H-1111 (Hungary); Nagy-Kovács, Teodóra [Budapest University of Technology and Economics, Department of Inorganic and Analytical Chemistry, Szent Gellért tér 4, Budapest, H-1111 (Hungary); Lukács, István [Hungarian Academy of Sciences, Research Centre for Energy, Institute of Technical Physics and Materials Science, H-1121 Budapest, Konkoly Thege M. út 29-33 (Hungary); Szilágyi, Imre M., E-mail: imre.szilagyi@mail.bme.hu [MTA-BME Technical Analytical Chemistry Research Group, Szent Gellért tér 4, Budapest, H-1111 (Hungary); Budapest University of Technology and Economics, Department of Inorganic and Analytical Chemistry, Szent Gellért tér 4, Budapest, H-1111 (Hungary)

2016-03-25

In the present study, two different methods for preparing hexagonal WO{sub 3} (h-WO{sub 3}) photocatalysts were used - controlled thermal decomposition and hydrothermal synthesis. WO{sub 3} nanoparticles with hexagonal structure were obtained by annealing (NH{sub 4}){sub x}WO{sub 3-y} at 500 °C in air. WO{sub 3} nanorods were prepared by a hydrothermal method using sodium tungstate Na{sub 2}WO{sub 4}, HCl, (COOH){sub 2} and NaSO{sub 4} precursors at 200 °C. The formation, morphology, structure and composition of the as-prepared nanoparticles and nanorods were studied by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDX). The photocatalytic activity of the h-WO{sub 3} nanoparticles and nanorods was studied by decomposing methyl orange in aqueous solution under UV light irradiation.

Tungsten oxide-graphene oxide (WO3-GO) nanocomposite as an efficient photocatalyst, antibacterial and anticancer agent

Science.gov (United States)

Jeevitha, G.; Abhinayaa, R.; Mangalaraj, D.; Ponpandian, N.

2018-05-01

Functioning of ultrasonically prepared tungsten oxide-graphene oxide (WO3-GO) nanocomposite as a photocatalyst, antibacterial and anticancer system was investigated and the obtained results were compared with that of pure WO3 nanoparticles. Structural, morphological, compositional and optical properties of the prepared WO3 nanoparticles and WO3-GO nanocomposite were studied. Photocatalytic efficiency of the system on organic dyes such as methylene blue (MB, cationic) and indigo carmine (IC, anionic) was investigated. The enhanced efficiency of the WO3-GO nanocomposite system was evaluated under sunlight and compared with that of pure WO3. The degradation efficiency values for MB and IC were found to be 97.03% and 95.43% at 180 and 120 min respectively. Antibacterial activity of the WO3-GO nanocomposite under visible light was tested and improved inhibition results were observed for Escherichia coli and Bacillus subtilis after 6 h of light exposure. The photocatalytic degradation efficiency and antibacterial activity of the WO3-GO nanocomposite are attributed to the improved electron-hole pair separation rate. Investigation on anticancer activity of WO3-GO nanocomposite was tested on human lung cancer (A-549) cell line and the IC50 value was found to be 139.6 ± 4.53 μg/mL. The results obtained in this study may be used as a platform for the development of photocatalysis applications based on WO3-GO nanocomposite.

Ease synthesis of mesoporous WO3-TiO2 nanocomposites with enhanced photocatalytic performance for photodegradation of herbicide imazapyr under visible light and UV illumination.

Science.gov (United States)

Ismail, Adel A; Abdelfattah, Ibrahim; Helal, Ahmed; Al-Sayari, S A; Robben, L; Bahnemann, D W

2016-04-15

Herein, we report the ease synthesis of mesoporous WO3-TiO2 nanocomposites at different WO3 contents (0-5wt%) together with their photocatalytic performance for the degradation of the imazapyr herbicide under visible light and UV illumination. XRD and Raman spectra indicated that the highly crystalline anatase TiO2 phase and monoclinic and triclinic of WO3 were formed. The mesoporous TiO2 exhibits large pore volumes of 0.267cm(3)g-1 and high surface areas of 180m(2)g(-1) but they become reduced to 0.221cm(3)g(-1) and 113m(2)g(-1), respectively upon WO3 incorporation, with tunable mesopore diameter in the range of 5-6.5nm. TEM images show WO3-TiO2 nanocomposites are quite uniform with 10-15nm of TiO2 and 5-10nm of WO3 sizes. Under UV illumination, the overall photocatalytic efficiency of the 3% WO3-TiO2 nanocomposite is 3.5 and 6.6 times higher than that of mesoporous TiO2 and commercial UV-100 photocatalyst, respectively. The 3% WO3-TiO2 nanocomposite is considered to be the optimum photocatalyst which is able to degrade completely (100% conversion) of imazapyr herbicide along 120min with high photonic efficiency ∼8%. While under visible light illumination, the 0.5% WO3-TiO2 nanocomposite is the optimum photocatalyst which achieves 46% photocatalytic efficiency. Copyright © 2015 Elsevier B.V. All rights reserved.

Facile Preparation of Nano-Bi2MoO6/Diatomite Composite for Enhancing Photocatalytic Performance under Visible Light Irradiation

Directory of Open Access Journals (Sweden)

Lu Cai

2018-02-01

Full Text Available In this work, a new nano-Bi2MoO6/diatomite composite photocatalyst was successfully synthesized by a facile solvothermal method. Scanning electron microscopy (SEM, Fourier transform infrared spectroscopy (FTIR, X-ray diffraction (XRD, and UV-vis diffuse reflection spectroscopy (DRS were employed to investigate the morphology, crystal structure, and optical properties. It was shown that nanometer-scaled Bi2MoO6 crystals were well-deposited on the surface of Bi2MoO6/diatomite. The photocatalytic activity of the obtained samples was evaluated by the degradation of rhodamine B (RhB under the visible light (λ > 420 nm irradiation. Moreover, trapping experiments were performed to investigate the possible photocatalytic reaction mechanism. The results showed that the nano-Bi2MoO6/diatomite composite with the mass ratio of Bi2MoO6 to diatomaceous earth of 70% exhibited the highest activity, and the RhB degradation efficiency reached 97.6% within 60 min. The main active species were revealed to be h+ and•O2−. As a photocatalytic reactor, its recycling performance showed a good stability and reusability. This new composite photocatalyst material holds great promise in the engineering field for the environmental remediation.

Facile Preparation of Nano-Bi2MoO6/Diatomite Composite for Enhancing Photocatalytic Performance under Visible Light Irradiation

Science.gov (United States)

Gong, Jiuyan; Liu, Jianshe; Song, Wendong; Ji, Lili

2018-01-01

In this work, a new nano-Bi2MoO6/diatomite composite photocatalyst was successfully synthesized by a facile solvothermal method. Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and UV-vis diffuse reflection spectroscopy (DRS) were employed to investigate the morphology, crystal structure, and optical properties. It was shown that nanometer-scaled Bi2MoO6 crystals were well-deposited on the surface of Bi2MoO6/diatomite. The photocatalytic activity of the obtained samples was evaluated by the degradation of rhodamine B (RhB) under the visible light (λ > 420 nm) irradiation. Moreover, trapping experiments were performed to investigate the possible photocatalytic reaction mechanism. The results showed that the nano-Bi2MoO6/diatomite composite with the mass ratio of Bi2MoO6 to diatomaceous earth of 70% exhibited the highest activity, and the RhB degradation efficiency reached 97.6% within 60 min. The main active species were revealed to be h+ and•O2−. As a photocatalytic reactor, its recycling performance showed a good stability and reusability. This new composite photocatalyst material holds great promise in the engineering field for the environmental remediation. PMID:29425138

X-ray photoelectron spectroscopy study of BaWO{sub 4} and Ba{sub 2}CaWO{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Capece, Angela M., E-mail: acapece@pppl.gov [California Institute of Technology, Pasadena, CA (United States); Polk, James E. [Jet Propulsion Laboratory, Pasadena, CA (United States); Shepherd, Joseph E. [California Institute of Technology, Pasadena, CA (United States)

2014-12-15

Highlights: • XPS reference spectra for Ba{sub 2}CaWO{sub 6} and BaWO{sub 4} are presented. • Binding energies of Ba 3d and W 4f lines are 0.7 eV higher for BaWO{sub 4} than Ba{sub 2}CaWO{sub 6}. • Ca 2p spectrum contains two sets of Ca 2p doublets attributed to Ba{sub 2}CaWO{sub 6} and CaCO{sub 3}. - Abstract: XPS reference spectra for Ba{sub 2}CaWO{sub 6} and BaWO{sub 4} are presented, including high resolution spectra of the Ba 3d, W 4f, C 1s, Ca 2p, and O 1s lines. The peak locations and full widths at half maximum are also given. The binding energies of the Ba 3d and W 4f lines are 0.7 eV higher for BaWO{sub 4} than for Ba{sub 2}CaWO{sub 6}. The Ca 2p spectrum contains two sets of Ca 2p doublets that were attributed to Ba{sub 2}CaWO{sub 6} and CaCO{sub 3}.

Novel ZnWO4/RGO nanocomposite as high performance photocatalyst

Directory of Open Access Journals (Sweden)

Mohamed Jaffer Sadiq Mohamed

2017-01-01

Full Text Available In this study, we report the synthesis of nanocomposite material composed of zinc tungstate (ZnWO4 and reduced graphene oxide (RGO as photocatalyst by a simple microwave irradiation technique. The prepared nanocomposites have been characterized by X-ray diffraction (XRD, transmission electron microscopy (TEM, energy dispersive X-ray (EDX analysis, X-ray photoelectron spectroscopy (XPS, Fourier transform infrared spectrometer (FTIR, photoluminescence spectroscopy (PL and UV-Visible spectroscopy. The photocatalytic activities of the prepared nanocomposites are evaluated in terms of the efficiencies of photodegradation of methylene blue (MB dye in aqueous solution under visible light irradiation. The prepared nanocomposites showed excellent photodegradation efficiency compared to the commercial TiO2 under visible light irradiation. The activity of the catalyst towards methyl orange (MO and rhodamine B (RB was also good. Further, in view of the low cost, simple preparation method and high catalytic activity of the material, it is expected that the prepared nanocomposite can serve as an environment friendly photocatalyst for treating the large scale industrial waste waters.

N, Fe and WO3 modified TiO2 for degradation of formaldehyde

International Nuclear Information System (INIS)

Tong Haixia; Zhao Li; Li Dan; Zhang Xiongfei

2011-01-01

Graphical abstract: The undoped TiO 2 powder (T(0)) shows strong photoabsorption only at wavelengths shorter than 400 nm, and while Fe 3+ and N-doped TiO 2 nanoparticles show photoabsorption in visible region and the absorption edge shifts to a longer wavelength. WO 3 compounding also benefits the photoabsorption in visible region. Display Omitted Highlights: → The preparation of the catalysts co-doped by Fe, N and compounded by WO 3 . → The obvious sculptured 'pattern' of the catalysts doped by Fe in the SEM images. → Strengthened photoabsorption to visible light of the modified catalysts from UV-DRS analysis. - Abstract: Butyltitanate, ethanol and glacial acetic acid were chosen as titanium source, solvent and chelating agent, respectively, via a sol-gel method combined impregnation method to prepare N, Fe co-doped and WO 3 compounded photocatalyst TiO 2 powder. The synthesized products were characterized by X-ray diffraction (XRD), diffuse reflectance UV-Vis spectra (UV-DRS), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). Photocatalytic degradation of formaldehyde was employed to investigate the catalytic activity. The results show that the degradation rate is 77.61% in 180 min under UV light irradiation when the concentration of N is fixed on, and the optimum proportioning ratio of n(Fe):n(W):n(Ti) is 0.5:2:100.

Synthesis of WO3 nanoparticles by citric acid-assisted precipitation and evaluation of their photocatalytic properties

International Nuclear Information System (INIS)

Sánchez-Martínez, D.; Martínez-de la Cruz, A.; López-Cuéllar, E.

2013-01-01

Graphical abstract: Display Omitted Highlights: ► WO 3 nanoparticles were synthesized by a simple citric acid-assisted precipitation. ► WO 3 photocatalyst was able to the partial mineralization of rhB, IC and MO. ► WO 3 can be considered as a photocatalyst active under visible light irradiation. -- Abstract: WO 3 nanoparticles were synthesized by citric acid-assisted precipitation method using a 1:1.5 molar ratio of ammonium paratungstate hydrate (H 42 N 10 O 42 W 12 ·xH 2 O):citric acid (C 6 H 8 O 7 ). The formation of monoclinic crystal structure of WO 3 at different temperatures was confirmed by X-ray powder diffraction (XRD). The characterization of the samples synthesized was complemented by transmission electron microscopy (TEM), Brunauer–Emmitt–Teller surface area (BET) and diffuse reflectance spectroscopy (DRS). According to the thermal treatment followed during the synthesis of WO 3 , the morphology of the nanoparticles formed was characterized by rectangular and ovoid shapes. The photocatalytic activity of WO 3 obtained under different experimental conditions was evaluated in the degradation of rhodamine B (rhB), indigo carmine (IC), methyl orange (MO), and Congo red (CR) in aqueous solution under UV and UV–vis radiation. The highest photocatalytic activity was observed in the sample obtained by thermal treatment at 700 °C. In general, the sequence of degradation of the organic dyes was: indigo carmine (IC) > rhodamine B (rhB) > methyl orange (MO) > Congo red (CR). The mineralization degree of organic dyes by WO 3 photocatalysts was determined by total organic carbon analysis (TOC) reaching percentages of mineralization of 82% (rhB), 85% (IC), 28% (MO), and 7% (CR) for 96 h of lamp irradiation.

Phase transitions and electrical properties of Bi2W1−xNbxO6−y and Bi2W1−xTaxO6−y

International Nuclear Information System (INIS)

Kharitonova, E.P.; Voronkova, V.I.; Gagor, A.B.; Pietraszko, A.P.; Alekseeva, O.A.

2013-01-01

Highlights: •The limit of Bi 2 W 1−x Me x O 6−y solid solutions is at x = 0.1, 0.15 for Me = Nb, Ta. •Ta and Nb substitutions for W suppress the reconstructive phase transition. •Bi 2 W 0.9 Nb 0.1 O 6−y samples belong to Aurivillius-type structure up to their melting. •Nb and Ta doping shifts ferroelectric transition to low temperatures up to 200 °C. •The highest conductivity reaches 10 −1 S/cm at 800 °C (x = 0.05, 0.1; Me = Nb, Ta). -- Abstract: Polycrystalline samples of Bi 2 W 1−x Me x O 6−y (Me = Nb, Ta) solid solutions have been prepared by solid-state reactions, and the influence of Nb and Ta substitutions for W on the polymorphism and electrical properties of Bi 2 WO 6 has been studied. The limit of the solid solutions is at x = 0.1 for Me = Nb and at x = 0.15 for Me = Ta. The distinctive features of the polymorphism of the Nb- and Ta-doped materials have been identified. According to differential scanning calorimetry data, tantalum and niobium substitutions for tungsten increase the temperature of the high-temperature, orthorhombic-to-monoclinic reconstructive phase transition and suppress the transition starting at x = 0.05 for Me = Nb and x = 0.10 for Me = Ta. As a result, the Bi 2 W 1−x Nb x O 6−y samples have an orthorhombic Aurivillius-type structure up to their melting point. The Bi 2 W 1−x Ta x O 6−y solid solutions at high temperatures consist of a mixture of an orthorhombic and a monoclinic phase. Nb and Ta doping shifts the ferroelectric phase transition to lower temperatures by more than 200 °C, thus markedly extending the stability range of the nonpolar orthorhombic paraelectric phase, which exists in a temperature range as narrow as 930–960 °C in the case of undoped Bi 2 WO 6 . The increase in oxygen vacancy concentration due to heterovalent substitutions of Nb 5+ and Ta 5+ for W 6+ leads to an increase in conductivity by two orders of magnitude relative to the unsubstituted compound

Photoinduced Glycerol Oxidation over Plasmonic Au and AuM (M = Pt, Pd and Bi) Nanoparticle-Decorated TiO2 Photocatalysts

Science.gov (United States)

Jedsukontorn, Trin; Saito, Nagahiro; Hunsom, Mali

2018-01-01

In this study, sol-immobilization was used to prepare gold nanoparticle (Au NP)-decorated titanium dioxide (TiO2) photocatalysts at different Au weight % (wt. %) loading (Aux/TiO2, where x is the Au wt. %) and Au–M NP-decorated TiO2 photocatalysts (Au3M3/TiO2), where M is bismuth (Bi), platinum (Pt) or palladium (Pd) at 3 wt. %. The Aux/TiO2 photocatalysts exhibited a stronger visible light absorption than the parent TiO2 due to the localized surface plasmon resonance effect. Increasing the Au content from 1 wt. % to 7 wt. % led to increased visible light absorption due to the increasing presence of defective structures that were capable of enhancing the photocatalytic activity of the as-prepared catalyst. The addition of Pt and Pd coupled with the Au3/TiO2 to form Au3M3/TiO2 improved the photocatalytic activity of the Au3/TiO2 photocatalyst by maximizing their light-absorption property. The Au3/TiO2, Au3Pt3/TiO2 and Au3Pd3/TiO2 photocatalysts promoted the formation of glyceraldehyde from glycerol as the principle product, while Au3Bi3/TiO2 facilitated glycolaldehyde formation as the major product. Among all the prepared photocatalysts, Au3Pd3/TiO2 exhibited the highest photocatalytic activity with a 98.75% glycerol conversion at 24 h of reaction time. PMID:29690645

Synthesis and luminescent properties of two different Y{sub 2}WO{sub 6}:Eu{sup 3+} phosphor phases

Energy Technology Data Exchange (ETDEWEB)

Llanos, Jaime, E-mail: jllanos@ucn.cl [Departamento de Química, Universidad Católica del Norte, Avda. Angamos 0610, Antofagasta (Chile); Olivares, Douglas [Departamento de Química, Universidad Católica del Norte, Avda. Angamos 0610, Antofagasta (Chile); Manríquez, Víctor; Espinoza, Darío [Departamento de Química, Universidad de Chile, Las Palmeras 3425, Santiago (Chile); Brito, Ivan [Departamento de Química, Universidad de Antofagasta, Campus Coloso, Antofagasta (Chile)

2015-04-15

Highlights: • Synthesis of two phases Y{sub 2−x}Eu{sub x}WO{sub 6}. One of them crystallizes as Aurivillius phase. • Optical properties of the phosphors Y{sub 2}WO{sub 6}:Eu{sup 3+} (monoclinic and orthorhombic phases). • The orthorhombic phase was prepared via low-temperature combustion synthesis method. - Abstract: In this paper, two different Y{sub 2−x}Eu{sub x}WO{sub 6} phases were synthesized. The monoclinic phase was prepared via a conventional solid-state reaction, whereas the orthorhombic phase was obtained via a facile, low-temperature combustion synthesis method. X-ray diffraction (XRD), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and photoluminescence (PL) spectroscopy were used to characterize the resulting phosphors. The XRD results indicate the orthorhombic phase crystallized isostructurally with the Aurivillius Bi{sub 2}WO{sub 6} phase, whereas the other polymorph crystallized isostructurally with Yb{sub 2}WO{sub 6} in the monoclinic system. The SEM studies revealed both phases had a strong tendency to form agglomerates averaging nanometers in size. The photoluminescence emission spectra confirmed all of the samples were efficiently excited by near UV light and were dominated by the electric dipole transition {sup 5}D{sub 0} → {sup 7}F{sub 2}. The orthorhombic Y{sub 2−x}Eu{sub x}WO{sub 6} excitation spectrum possessed a broad band across the entire UV region (220–400 nm); therefore, Y{sub 1.86}Eu{sub 0.14}WO{sub 6} could be considered an efficient spectral converter material for use in dye-sensitized solar cells.

State-of-the-art Sn2+-based ternary oxides as photocatalysts for water splitting: electronic structures and optoelectronic properties

KAUST Repository

Noureldine, Dalal

2016-09-19

Developing visible light responsive metal oxide photocatalysts is a challenge that must be conquered to achieve high efficiency for water splitting or hydrogen evolution reactions. Valence band engineering is possible by forming ternary oxides using the combination of a metal cation with an s2d10 electronic configuration and a transition metal oxide with a d0 configuration. Many (Sn2+, Bi3+, Pb2+)-based ternary metal oxide photocatalysts have been reported for hydrogen and/or oxygen evolution under visible irradiation. Sn2+-based materials have attracted particular attention because tin is inexpensive, abundant and more environmentally friendly than lead or bismuth. In this review, we provide a fruitful library for Sn2+-based photocatalysts that have been reported to evolve hydrogen using sacrificial reagents, including SnNb2O6, Sn2Nb2O7, SnTaxNb2−xO6, SnTa2O6, Sn2Ta2O7, SnWO4 (α and β phases), SnSb2O6·nH2O, and Sn2TiO4. The synthesis method used in the literature and the resultant morphology and crystal structure of each compound are discussed. The density functional theory (DFT) calculations of the electronic structure and density of states are provided, and the consequent optoelectronic properties such as band gap, nature of the bandgap, dielectric constant, and effective masses are summarized. This review will help highlight the main challenges for Sn2+-based materials.

State-of-the-art Sn2+-based ternary oxides as photocatalysts for water splitting: electronic structures and optoelectronic properties

KAUST Repository

Noureldine, Dalal; Takanabe, Kazuhiro

2016-01-01

Developing visible light responsive metal oxide photocatalysts is a challenge that must be conquered to achieve high efficiency for water splitting or hydrogen evolution reactions. Valence band engineering is possible by forming ternary oxides using the combination of a metal cation with an s2d10 electronic configuration and a transition metal oxide with a d0 configuration. Many (Sn2+, Bi3+, Pb2+)-based ternary metal oxide photocatalysts have been reported for hydrogen and/or oxygen evolution under visible irradiation. Sn2+-based materials have attracted particular attention because tin is inexpensive, abundant and more environmentally friendly than lead or bismuth. In this review, we provide a fruitful library for Sn2+-based photocatalysts that have been reported to evolve hydrogen using sacrificial reagents, including SnNb2O6, Sn2Nb2O7, SnTaxNb2−xO6, SnTa2O6, Sn2Ta2O7, SnWO4 (α and β phases), SnSb2O6·nH2O, and Sn2TiO4. The synthesis method used in the literature and the resultant morphology and crystal structure of each compound are discussed. The density functional theory (DFT) calculations of the electronic structure and density of states are provided, and the consequent optoelectronic properties such as band gap, nature of the bandgap, dielectric constant, and effective masses are summarized. This review will help highlight the main challenges for Sn2+-based materials.

Synthesis of WO{sub 3} nanoparticles by citric acid-assisted precipitation and evaluation of their photocatalytic properties

Energy Technology Data Exchange (ETDEWEB)

Sánchez-Martínez, D. [Departamento de Ecomateriales y Energía, Facultad de Ingeniería Civil (UANL), Ciudad Universitaria, C.P. 66451, San Nicolás de los Garza, N.L. (Mexico); Martínez-de la Cruz, A., E-mail: azael70@yahoo.com.mx [Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451, San Nicolás de los Garza, N.L. (Mexico); López-Cuéllar, E. [Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451, San Nicolás de los Garza, N.L. (Mexico)

2013-02-15

Graphical abstract: Display Omitted Highlights: ► WO{sub 3} nanoparticles were synthesized by a simple citric acid-assisted precipitation. ► WO{sub 3} photocatalyst was able to the partial mineralization of rhB, IC and MO. ► WO{sub 3} can be considered as a photocatalyst active under visible light irradiation. -- Abstract: WO{sub 3} nanoparticles were synthesized by citric acid-assisted precipitation method using a 1:1.5 molar ratio of ammonium paratungstate hydrate (H{sub 42}N{sub 10}O{sub 42}W{sub 12}·xH{sub 2}O):citric acid (C{sub 6}H{sub 8}O{sub 7}). The formation of monoclinic crystal structure of WO{sub 3} at different temperatures was confirmed by X-ray powder diffraction (XRD). The characterization of the samples synthesized was complemented by transmission electron microscopy (TEM), Brunauer–Emmitt–Teller surface area (BET) and diffuse reflectance spectroscopy (DRS). According to the thermal treatment followed during the synthesis of WO{sub 3}, the morphology of the nanoparticles formed was characterized by rectangular and ovoid shapes. The photocatalytic activity of WO{sub 3} obtained under different experimental conditions was evaluated in the degradation of rhodamine B (rhB), indigo carmine (IC), methyl orange (MO), and Congo red (CR) in aqueous solution under UV and UV–vis radiation. The highest photocatalytic activity was observed in the sample obtained by thermal treatment at 700 °C. In general, the sequence of degradation of the organic dyes was: indigo carmine (IC) > rhodamine B (rhB) > methyl orange (MO) > Congo red (CR). The mineralization degree of organic dyes by WO{sub 3} photocatalysts was determined by total organic carbon analysis (TOC) reaching percentages of mineralization of 82% (rhB), 85% (IC), 28% (MO), and 7% (CR) for 96 h of lamp irradiation.

Microwave-assisted in situ synthesis of reduced graphene oxide-BiVO4 composite photocatalysts and their enhanced photocatalytic performance for the degradation of ciprofloxacin.

Science.gov (United States)

Yan, Yan; Sun, Shaofang; Song, Yang; Yan, Xu; Guan, Weisheng; Liu, Xinlin; Shi, Weidong

2013-04-15

To improve the photodegradation efficiency for ciprofloxacin (CIP), a new-type microwave-assisted in situ growth method is developed for the preparation of reduced graphene oxide (RGO) -BiVO4 composite photocatalysts. The as-produced RGO-BiVO4 composite photocatalysts show extremely high enhancement of CIP degradation ratio over the pure BiVO4 photocatalyst under visible light. Specially, the 2 wt% RGO-BiVO4 composite photocatalyst exhibits the highest CIP degradation ratio (68.2%) in 60 min, which is over 3 times than that (22.7%) of the pure BiVO4 particles. The enhancement of photocatalytic activities of RGO-BiVO4 photocatalysts can be attributed to the effective separation of electron-hole pairs rather than the improvement of light absorption. Copyright © 2013 Elsevier B.V. All rights reserved.

Facile Br- assisted hydrothermal synthesis of Bi2MoO6 nanoplates with enhanced visible-light photocatalytic activity

International Nuclear Information System (INIS)

Zhang, Peng; Teng, Xiaoxu; Liu, Dongsheng; Fu, Liang; Xie, Hualin; Zhang, Guoqing; Ding, Shimin

2017-01-01

Bi 2 MoO 6 nanoplates have been controllably synthesized via a facile hydrothermal process with the assistance of Br - containing surfactant cetyltrimethylammonium bromide (CTAB) or KBr. A remarkable enhancement in the visible-light-driven photocatalytic degradation of Rhodamine B was observed. It was found that reaction temperature and surfactant play crucial roles in the formation and properties of the Bi 2 MoO 6 nanoplates. The best results as photocatalyst were obtained with the sample hydrothermally synthesized at 150 C with the assistance of CTAB. The improved photocatalytic performance could be ascribed to the {001}-oriented nanostructure of the Bi 2 MoO 6 nanoplates. KBr-templated Bi 2 MoO 6 nanoplates also showed better photocatalytic efficiency compared with that of flower-like Bi 2 MoO 6 but inferior to that of CTAB-templated Bi 2 MoO 6 nanoplates. (orig.)

Ease synthesis of mesoporous WO{sub 3}–TiO{sub 2} nanocomposites with enhanced photocatalytic performance for photodegradation of herbicide imazapyr under visible light and UV illumination

Energy Technology Data Exchange (ETDEWEB)

Ismail, Adel A., E-mail: adelali141@yahoo.com [Advanced Materials Department, Central Metallurgical R& D Institute, CMRDI, P.O. Box 87, Helwan 11421 Cairo (Egypt); Advanced Materials and Nano Research Center, Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Abdelfattah, Ibrahim [Water Pollution Research Dept., National Research Centre, 33 EL Bohouth St. (Former EL Tahrir St.), P.O. 12622, Dokki, Giza (Egypt); Helal, Ahmed [Advanced Materials Department, Central Metallurgical R& D Institute, CMRDI, P.O. Box 87, Helwan 11421 Cairo (Egypt); Al-Sayari, S.A. [Advanced Materials and Nano Research Center, Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Robben, L. [Chemische Kristallographie fester Stoffe, Universität Bremen (Germany); Bahnemann, D.W. [Institut für Technische Chemie, Leibniz Universität Hannover, Callinstrasse 3, 30167 Hannover (Germany)

2016-04-15

Highlights: • Ease synthesis of mesoporous WO{sub 3}–TiO{sub 2} nanocomposites were performed. • XRD and Raman spectra confirmed that monoclinic and triclinic of WO{sub 3} was detected. • The prepared photocatalysts were evaluated for photodegradation of imazapyr. • It could be completely degraded of imazapyr within 120 min under UV light. • Under visible light, 0.5%WO{sub 3}–TiO{sub 2} is the optimum with 46% photocatalytic efficiency. - Abstract: Herein, we report the ease synthesis of mesoporous WO{sub 3}–TiO{sub 2} nanocomposites at different WO{sub 3} contents (0–5 wt%) together with their photocatalytic performance for the degradation of the imazapyr herbicide under visible light and UV illumination. XRD and Raman spectra indicated that the highly crystalline anatase TiO{sub 2} phase and monoclinic and triclinic of WO{sub 3} were formed. The mesoporous TiO{sub 2} exhibits large pore volumes of 0.267 cm{sup 3} g−1 and high surface areas of 180 m{sup 2} g{sup −1} but they become reduced to 0.221 cm{sup 3} g{sup −1} and 113 m{sup 2} g{sup −1}, respectively upon WO{sub 3} incorporation, with tunable mesopore diameter in the range of 5–6.5 nm. TEM images show WO{sub 3}–TiO{sub 2} nanocomposites are quite uniform with 10–15 nm of TiO{sub 2} and 5–10 nm of WO{sub 3} sizes. Under UV illumination, the overall photocatalytic efficiency of the 3% WO{sub 3}–TiO{sub 2} nanocomposite is 3.5 and 6.6 times higher than that of mesoporous TiO{sub 2} and commercial UV-100 photocatalyst, respectively. The 3% WO{sub 3}–TiO{sub 2} nanocomposite is considered to be the optimum photocatalyst which is able to degrade completely (100% conversion) of imazapyr herbicide along 120 min with high photonic efficiency ∼8%. While under visible light illumination, the 0.5% WO{sub 3}–TiO{sub 2} nanocomposite is the optimum photocatalyst which achieves 46% photocatalytic efficiency.

Study of multiferroic properties of Bi2Fe2WO9 ceramic for device application

OpenAIRE

Jyoshna Rout; R. N. P. Choudhary

2016-01-01

The Bi2Fe2WO9 ceramic was prepared using a standard solid-state reaction technique. Preliminary analysis of X-ray diffraction pattern revealed the formation of single-phase compound with orthorhombic crystal symmetry. The surface morphology of the material captured using scanning electron microscope (SEM) exhibits formation of a densely packed microstructure. Comprehensive study of dielectric properties showed two anomalies at 200∘C and 450∘C: first one may be related to magnetic whereas seco...

Characterization of nanosized Al2(WO4)3

International Nuclear Information System (INIS)

Nihtianova, D.; Velichkova, N.; Nikolova, R.; Koseva, I.; Yordanova, A.; Nikolov, V.

2011-01-01

Graphical abstract: TEM method allows to detect small quantities of impurities not detectable by other methods. In our case impurities of W 5 O 14 are detected in Al 2 (WO 4 ) 3 nanopowder. Highlights: → Nanosized Al 2 (WO 4 ) 3 by simple co-precipitation method. → Spherical particles with mean size of 22 nm distributed between 10 and 40 nm at 630 o C. → XRD, DTA and TEM confirm well defined products with perfect structure. → TEM locality allows detection of impurities not detectable by XRD and DTA. -- Abstract: Nanosized aluminum tungstate Al 2 (WO 4 ) 3 was prepared by co-precipitation reaction between Na 2 WO 4 and Al(NO 3 ) 3 aqueous solutions. The powder size and shape, as well as size distribution are estimated after different conditions of powder preparation. The purity of the final product was investigated by XRD and DTA analyses, using the single crystal powder as reference. Between the specimen and the reference no difference was detected. The crystal structure of Al 2 (WO 4 ) 3 nanosized powder was confirmed by TEM (SAED, HRTEM). In additional, TEM locality allows to detect some W 5 O 14 impurities, which are not visible by conventional X-ray powder diffraction and thermal analyses.

AgBr/MgBi2O6 heterostructured composites with highly efficient visible-light-driven photocatalytic activity

Science.gov (United States)

Zhong, Liansheng; Hu, Chaohao; Zhuang, Jing; Zhong, Yan; Wang, Dianhui; Zhou, Huaiying

2018-06-01

AgBr/MgBi2O6 heterostructured photocatalysts were synthesized by the deposition-precipitation method. X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL), and UV-Visible diffuse reflectance spectroscopy (UV-Vis DRS) were employed to examine the phase structure, morphology and optical properties of the as-prepared samples. The photocatalytic activity was investigated by decomposing methylene blue (MB) solution under visible light irradiation (λ > 420 nm). AgBr/MgBi2O6 composites exhibited significantly enhanced visible-light-driven photocatalytic properties in comparison with pure MgBi2O6 and AgBr. When the molar ratio of AgBr to MgBi2O6 was 3:1, the composite catalyst showed the optimal photocatalytic activity and excellent stability. The enhanced photocatalytic activity of AgBr/MgBi2O6 composites was attributed to the formation of p-n heterojunction between AgBr and MgBi2O6, thereby resulting in the effective separation and transfer of photogenerated electrons-hole pairs.

Synthesis, characterization and photocatalytic activity of WO3/TiO2 for NO removal under UV and visible light irradiation

International Nuclear Information System (INIS)

Luévano-Hipólito, E.; Martínez-de la Cruz, A.; López-Cuellar, E.; Yu, Q.L.; Brouwers, H.J.H.

2014-01-01

Samples with different proportions WO 3 /TiO 2 were prepared by co-precipitation method followed by a heat treatment. The samples were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS), and adsorption–desorption N 2 isotherms (BET). The photocatalytic properties of WO 3 /TiO 2 samples were evaluated in the photo-oxidation reaction of nitric oxide (NO) under UV and visible light irradiation. The highest photocatalytic activity was observed in the WO 3 /TiO 2 sample with a composition of 80% mole of TiO 2 . Among the different substrates used for supporting the photocatalyst, the best results were reached over concrete and glass when it was exposed to UV and visible light irradiation, respectively. In overall, the photocatalytic efficiency of the synthesized materials was higher under UV than visible light irradiation. - Highlights: • WO 3 /TiO 2 prepared in simple way show high photocatalytic activity for NO removal. • The concrete was the best substrate to the performance of WO 3 /TiO 2 with UV radiation. • The glass was the best substrate to the performance of WO 3 /TiO 2 with visible radiation

Investigation of radiation shielding properties for MeO-PbCl2-TeO2 (MeO = Bi2O3, MoO3, Sb2O3, WO3, ZnO) glasses

Science.gov (United States)

Sayyed, M. I.; Çelikbilek Ersundu, M.; Ersundu, A. E.; Lakshminarayana, G.; Kostka, P.

2018-03-01

In this work, glasses in the MeO-PbCl2-TeO2 (MeO = Bi2O3, MoO3, Sb2O3, WO3, ZnO) system, which show a great potential for optoelectronic applications, were used to evaluate their resistance under high energy ionizing radiations. The basic shielding quantities for determining the penetration of radiation in glass, such as mass attenuation coefficient (μ/ρ), half value layer (HVL), mean free path (MFP) and exposure buildup factor (EBF) values were investigated within the energy range 0.015 MeV ‒ 15 MeV using XCOM program and variation of shielding parameters were compared with different glass systems and ordinary concrete. From the derived results, it was determined that MeO-PbCl2-TeO2 (MeO = Bi2O3, MoO3, Sb2O3, WO3, ZnO) glasses show great potentiality to be used under high energy radiations. Among the studied glass compositions, Bi2O3 and WO3 containing glasses were found to possess superior gamma-ray shielding effectiveness.

A heterojunction photocatalyst composed of zinc rhodium oxide, single crystal-derived bismuth vanadium oxide, and silver for overall pure-water splitting under visible light up to 740 nm.

Science.gov (United States)

Kobayashi, Ryoya; Takashima, Toshihiro; Tanigawa, Satoshi; Takeuchi, Shugo; Ohtani, Bunsho; Irie, Hiroshi

2016-10-12

We recently reported the synthesis of a solid-state heterojunction photocatalyst consisting of zinc rhodium oxide (ZnRh 2 O 4 ) and bismuth vanadium oxide (Bi 4 V 2 O 11 ), which functioned as hydrogen (H 2 ) and oxygen (O 2 ) evolution photocatalysts, respectively, connected with silver (Ag). Polycrystalline Bi 4 V 2 O 11 (p-Bi 4 V 2 O 11 ) powders were utilized to form ZnRh 2 O 4 /Ag/p-Bi 4 V 2 O 11 , which was able to photocatalyze overall pure-water splitting under red-light irradiation with a wavelength of 700 nm (R. Kobayashi et al., J. Mater. Chem. A, 2016, 4, 3061). In the present study, we replaced p-Bi 4 V 2 O 11 with a powder obtained by pulverizing single crystals of Bi 4 V 2 O 11 (s-Bi 4 V 2 O 11 ) to form ZnRh 2 O 4 /Ag/s-Bi 4 V 2 O 11 , and demonstrated that this heterojunction photocatalyst had enhanced water-splitting activity. In addition, ZnRh 2 O 4 /Ag/s-Bi 4 V 2 O 11 was able to utilize nearly the entire range of visible light up to a wavelength of 740 nm. These properties were attributable to the higher O 2 evolution activity of s-Bi 4 V 2 O 11 .

In situ loading of Ag_2WO_4 on ultrathin g-C_3N_4 nanosheets with highly enhanced photocatalytic performance

International Nuclear Information System (INIS)

Li, Yunfeng; Jin, Renxi; Fang, Xu; Yang, Yang; Yang, Man; Liu, Xianchun; Xing, Yan; Song, Shuyan

2016-01-01

Graphical abstract: Ultrathin g-C_3N_4 nanosheets (g-C_3N_4−NS) with improved electron transport ability and large number of active sites are employed instead of bulk g-C_3N_4 to prepare the Ag_2WO_4/g-C_3N_4−NS heterostructured photocatalysts, which exhibit remarkable photocatalytic activity for wastewater treatment. - Highlights: • Ag2WO4/g-C3N4-NS photocatalysts were obtained by a deposition-precipitation method. • Ag2WO4/g-C3N4-NS possess large surface areas and increased lifetime of charges. • Ag2WO4/g-C3N4-NS exhibit enhanced activity on degradation of RhB and MO. • The photocatalytic mechanism of the Ag2WO4/g-C3N4-NS system were investigated. - Abstract: The g-C_3N_4 nanosheets (g-C_3N_4−NS) exhibit more excellent property than common bulk g-C_3N_4 (g-C_3N_4-B) due to their large surface areas, improved electron transport ability and well dispersion in water. In this work, ultrathin g-C_3N_4−NS with a thickness of about 2.7 nm have been synthesized by a simple thermal exfoliation of bulk g-C_3N_4, and then Ag_2WO_4 nanoparticles are in situ loaded on their surface to construct the Ag_2WO_4/g-C_3N_4−NS heterostructured photocatalysts. Due to their unique physicochemical properties, the as-prepared heterostructures possess a fast interfacial charge transfer and increased lifetime of photo-excited charge carriers, and exhibit much higher photocatalytic activity. Under visible light irradiation, the optimum photocatalytic activity of Ag_2WO_4/g-C_3N_4−NS composites is almost 53.6 and 26.5 times higher than that of pure g-C_3N_4-B and Ag_2WO_4/g-C_3N_4-B heterostructures towards the degradation of rhodamine B, respectively, and is almost 30.6 and 9.8 times higher towards the degradation of methyl orange, respectively. In addition, the natural sunlight photocatalytic activities of the as-prepared samples are also investigated.

Vacancy-Rich Monolayer BiO2-x as a Highly Efficient UV, Visible, and Near-Infrared Responsive Photocatalyst.

Science.gov (United States)

Li, Jun; Wu, Xiaoyong; Pan, Wenfeng; Zhang, Gaoke; Chen, Hong

2018-01-08

Vacancy-rich layered materials with good electron-transfer property are of great interest. Herein, a full-spectrum responsive vacancy-rich monolayer BiO 2-x has been synthesized. The increased density of states at the conduction band (CB) minimum in the monolayer BiO 2-x is responsible for the enhanced photon response and photo-absorption, which were confirmed by UV/Vis-NIR diffuse reflectance spectra (DRS) and photocurrent measurements. Compared to bulk BiO 2-x , monolayer BiO 2-x has exhibited enhanced photocatalytic performance for rhodamine B and phenol removal under UV, visible, and near-infrared light (NIR) irradiation, which can be attributed to the vacancy V Bi-O ''' as confirmed by the positron annihilation spectra. The presence of V Bi-O ''' defects in monolayer BiO 2-x promoted the separation of electrons and holes. This finding provides an atomic level understanding for developing highly efficient UV, visible, and NIR light responsive photocatalysts. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Photoluminescence varied by selective excitation in BiGdWO6:Eu3+ phosphor

Science.gov (United States)

Pavani, K.; Graça, M. P. F.; Kumar, J. Suresh; Neves, A. J.

2017-12-01

Eu3+ doped bismuth gadolinium tungstate (BGW), a simplest member of Aurivillius family of layered perovskites, was synthesized by solid-state reaction method. Structural characterisation has been performed by X-Ray diffraction (XRD), Raman spectroscopy, Fourier Transform Infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). Band gap of the host matrix has been calculated using reflectance and absorption spectra. Three different mechanisms were found to explain the excitation of Eu3+ ions and are described in detail. Photoluminescence (PL) spectra of the BGW phosphor doped with Eu3+ ions consist of major emission lines associated with 5D0 → 7FJ (J = 0, 1, 2, 3 and 4) of Eu3+ ion. Site selective PL excitation and emission indicates that Eu3+ ions doped in BiGdWO6 are sensitive to the excitation wavelength without change in the structure. Change in emission spectra were observed when the excitation wavelength was changed. Judd-Ofelt (J-O) parameters were determined from the indirect method to interpret the interactions between the host and dopant ions along with detailed analysis of lifetime measurements.

Microwave-assisted in situ synthesis of reduced graphene oxide-BiVO{sub 4} composite photocatalysts and their enhanced photocatalytic performance for the degradation of ciprofloxacin

Energy Technology Data Exchange (ETDEWEB)

Yan, Yan [School of Chemistry and Chemical Engineering, Jiangsu University, Xuefu Road 301, Zhenjiang, 212013 (China); Sun, Shaofang [School of Chemistry and Chemical Engineering, Jiangsu University, Xuefu Road 301, Zhenjiang, 212013 (China); School of Environmental Science and Engineering, Chang’an University, Yanta Road 126, Xi’an, 710054 (China); Song, Yang; Yan, Xu [School of Chemistry and Chemical Engineering, Jiangsu University, Xuefu Road 301, Zhenjiang, 212013 (China); Guan, Weisheng [School of Environmental Science and Engineering, Chang’an University, Yanta Road 126, Xi’an, 710054 (China); Liu, Xinlin [School of Material Science and Engineering, Jiangsu University, Xuefu Road 301, Zhenjiang, 212013 (China); Shi, Weidong, E-mail: swd1978@ujs.edu.cn [School of Chemistry and Chemical Engineering, Jiangsu University, Xuefu Road 301, Zhenjiang, 212013 (China)

2013-04-15

Highlights: ► Microwave-assisted in situ growth of RGO-BiVO{sub 4} composite was proposed. ► A relatively small particle size with organic-additives free. ► Graphene was formed during the microwave-heating by oxygen capture. ► GB-2 sample exhibits the highest CIP degradation ratio (3 times over pure BiVO{sub 4}). ► The enhancements of activities result from the effective charge separation. -- Abstract: To improve the photodegradation efficiency for ciprofloxacin (CIP), a new-type microwave-assisted in situ growth method is developed for the preparation of reduced graphene oxide (RGO) -BiVO{sub 4} composite photocatalysts. The as-produced RGO-BiVO{sub 4} composite photocatalysts show extremely high enhancement of CIP degradation ratio over the pure BiVO{sub 4} photocatalyst under visible light. Specially, the 2 wt% RGO-BiVO{sub 4} composite photocatalyst exhibits the highest CIP degradation ratio (68.2%) in 60 min, which is over 3 times than that (22.7%) of the pure BiVO{sub 4} particles. The enhancement of photocatalytic activities of RGO-BiVO{sub 4} photocatalysts can be attributed to the effective separation of electron–hole pairs rather than the improvement of light absorption.

Modification of TiO{sub 2} nanorods by Bi{sub 2}MoO{sub 6} nanoparticles for high performance visible-light photocatalysis

Energy Technology Data Exchange (ETDEWEB)

Li Na; Zhu Li [School of Chemistry and Chemical Engineering, South China University of Technology, 381 Wushan Road, Guangzhou 510640 (China); Zhang Weide, E-mail: zhangwd@scut.edu.cn [School of Chemistry and Chemical Engineering, South China University of Technology, 381 Wushan Road, Guangzhou 510640 (China); Yu Yuxiang; Zhang Wenhui; Hou Meifang [School of Chemistry and Chemical Engineering, South China University of Technology, 381 Wushan Road, Guangzhou 510640 (China)

2011-10-13

Highlights: > Bi{sub 2}MoO{sub 6}/TiO{sub 2} heterojunction photocatalysts. > Effective separation of photoexcited electrons and holes. > High visible light photocatalytic activity. - Abstract: In this work, TiO{sub 2} nanorods were prepared by a hydrothermal process and then Bi{sub 2}MoO{sub 6} nanoparticles were deposited onto the TiO{sub 2} nanorods by a solvothermal process. The nanostructured Bi{sub 2}MoO{sub 6}/TiO{sub 2} composites were extensively characterized by X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy and UV-vis diffuse reflectance spectroscopy. The photocatalytic activity of the Bi{sub 2}MoO{sub 6}/TiO{sub 2} composites was evaluated by degradation of methylene blue. The Bi{sub 2}MoO{sub 6}/TiO{sub 2} composites exhibit higher catalytic activity than pure Bi{sub 2}MoO{sub 6} and TiO{sub 2} for degradation of methylene blue under visible light irradiation ({lambda} > 420 nm). Further investigation revealed that the ratio of Bi{sub 2}MoO{sub 6} to TiO{sub 2} in the composites greatly influenced their photocatalytic activity. The experimental results indicated that the composite with Bi{sub 2}MoO{sub 6}:TiO{sub 2} = 1:3 exhibited the highest photocatalytic activity. The enhancement mechanism of the composite catalysts was also discussed.

TiO2-V2O5 nanocomposites as alternative energy storage substances for photocatalysts.

Science.gov (United States)

Ngaotrakanwiwat, Pailin; Meeyoo, Vissanu

2012-01-01

TiO2-V2O5 was prepared and evaluated as an energy storage material for photocatalysts with high capacity and initial charging rate. The compound was successfully obtained by sol-gel technique and effects of compound composition and calcination temperature on the energy storage ability were investigated. The synthesized compounds were characterized by means of X-ray powder diffraction (XRD), scanning electron microscopy equipped with energy-dispersive X-ray analysis (SEM-EDX) and transmission electron microscopy (TEM). The results reveals that the compound of Ti:V molar ratio equal to 1:0.11 calcined at 550 degrees C exhibited superior energy storage ability than parent substances and 1.7-times higher capacity and 2.3-times higher initial charging rate compared to WO3, indicating that the compound is a remarkable alternative to conventional energy storage substances.

Hydrothermal synthesis of B-doped Bi2MoO6 and its high photocatalytic performance for the degradation of Rhodamine B

Science.gov (United States)

Wang, Min; Han, Jin; Guo, Pengyao; Sun, Mingzhi; Zhang, Yu; Tong, Zhu; You, Meiyan; Lv, Chunmei

2018-02-01

B-doped Bi2MoO6 photocatalysts have been synthesized by a hydrothermal method using HBO3 as the doping source and the effect of B doping content on Bi2MoO6 structure and performance was studied. The samples were characterized with XPS, XRD, SEM, BET, UV-Vis DRS, and PL. The photocatalytic activity was evaluated by photocatalytic degradation of Rhodamine B (RhB) under visible light (λ ≥ 420 nm). The results show that all samples are orthorhombic structure. Doping Bi2MoO6 with B increases the amount of Bi5+ and oxygen vacancies, which led to stronger absorption in visible light region and lower band gap energy of the B-doped Bi2MoO6 but had little impact on morphology. B doping significantly improves the photocatalytic activity of Bi2MoO6 and the highest photocatalytic degradation rate is 89% when the initial molar ratio of B to Bi is 0.01.

Facile Br{sup -} assisted hydrothermal synthesis of Bi{sub 2}MoO{sub 6} nanoplates with enhanced visible-light photocatalytic activity

Energy Technology Data Exchange (ETDEWEB)

Zhang, Peng [Yangtze Normal University, Chongqing Key Laboratory of Inorganic Special Functional Materials, Chongqing (China); Yangtze Normal University, College of Chemistry and Chemical Engineering, Chongqing (China); Teng, Xiaoxu; Liu, Dongsheng; Fu, Liang; Xie, Hualin [Yangtze Normal University, College of Chemistry and Chemical Engineering, Chongqing (China); Zhang, Guoqing [Yangtze Normal University, Chongqing Key Laboratory of Inorganic Special Functional Materials, Chongqing (China); Ding, Shimin [Yangtze Normal University, Collaborative Innovation Center for Green Development in Wuling Mountain Areas, Chongqing (China)

2017-10-15

Bi{sub 2}MoO{sub 6} nanoplates have been controllably synthesized via a facile hydrothermal process with the assistance of Br{sup -} containing surfactant cetyltrimethylammonium bromide (CTAB) or KBr. A remarkable enhancement in the visible-light-driven photocatalytic degradation of Rhodamine B was observed. It was found that reaction temperature and surfactant play crucial roles in the formation and properties of the Bi{sub 2}MoO{sub 6} nanoplates. The best results as photocatalyst were obtained with the sample hydrothermally synthesized at 150 C with the assistance of CTAB. The improved photocatalytic performance could be ascribed to the {001}-oriented nanostructure of the Bi{sub 2}MoO{sub 6} nanoplates. KBr-templated Bi{sub 2}MoO{sub 6} nanoplates also showed better photocatalytic efficiency compared with that of flower-like Bi{sub 2}MoO{sub 6} but inferior to that of CTAB-templated Bi{sub 2}MoO{sub 6} nanoplates. (orig.)

Sol-gel synthesis and characterizations of crystalline NaGd(WO4)2 powder for anisotropic transparent ceramic laser application

Science.gov (United States)

Durairajan, A.; Thangaraju, D.; Balaji, D.; Moorthy Babu, S.

2013-02-01

NaGd(WO4)2 powders were synthesized at different pH (3.5, 4.5, 5.5, 6.5 and 7.5) values by conventional Pechini method. Sodium and gadolinium nitrate salts and ammonium paratungstate are used as starting precursors. Metal cations were chelated by citric acid and individual citrates were bound together with ethylene glycol. Synthesized gel was analyzed using differential thermal analysis (DTA), thermo gravimetric (TG) and FT-IR spectroscopy to understand the degradation of gel and formation of metal citrates. Calcined powders (250, 600, 700 and 800 °C) were characterized by powder XRD, FT-IR, Raman and FE-SEM analysis. The temperature dependent phase formation was examined by powder XRD. The morphological changes at different pH derived powders were observed with FE-SEM micrographs. Stepwise organic liberation with respect to temperature and presence of carbon content in the pre-fired powder were analyzed using FT-IR analysis. Raman spectrum reveals disordered tungstate vibrations in the NGW matrix.

Experimental and theoretical investigation on photocatalytic activities of 1D Ag/Ag2WO4 nanostructures

Science.gov (United States)

Liu, Danqing; Huang, Weicheng; Li, Long; Liu, Lu; Sun, Xiaojun; Liu, Bo; Yang, Bin; Guo, Chongshen

2017-09-01

Ag2WO4 is a significant photocatalyst that responds to UV light irradiation only, which greatly hinders it for further practical application for solar light. To address this problem, herein, 1D plasmonic Ag/Ag2WO4 photocatalysts have been fabricated by a successive process including hydrothermal synthesis to obtain Ag2WO4 followed by an additional in situ chemical-reduction process for Ag decoration. Then, the structural features, optical properties, and electronic structures of Ag2WO4 and Ag/Ag2WO4 nanowires were systematically investigated via a combination of theoretical calculations and experimental evidence. The plasmon-enhanced Ag/Ag2WO4 nanowires exhibited higher visible-light-driven photocatalytic activity, which performed a desired photodestruction ratio of 91.2% on methylene blue within 60 min and good stability in five cycles. The Ag decoration greatly facilitates visible-light harvesting and thus promotes photogenerated radical oxidation to dye, which is evidenced by the higher hydroxyl radical level of Ag/Ag2WO4 detected in the ESR test during the photocatalytic process. The theoretical calculation based on density functional theory indicates that Ag nanoparticles formed on the surface of Ag2WO4 could narrow the band gap of Ag2WO4. In addition, the surface plasmon resonance absorption effect and fast charge transfer effect in the metal-semiconductor system contribute to the photocatalytic performance of Ag/Ag2WO4.

Facile synthesis of BiOF/Bi{sub 2}O{sub 3}/reduced graphene oxide photocatalyst with highly efficient and stable natural sunlight photocatalytic performance

Energy Technology Data Exchange (ETDEWEB)

Hu, Limin; Dong, Shuying; Li, Qilu; Feng, Jinglan; Pi, Yunqing; Liu, Menglin [School of Environment, Henan Normal University, Key Laboratory for Yellow River and Huai River Water Environmental and Pollution Control, Ministry of Education, Henan Key Laboratory for Environmental Pollution Control, Xinxiang, Henan 453007 (China); Sun, Jingyu, E-mail: sunjy-cnc@pku.edu.cn [Center for Nanochemistry (CNC), College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Sun, Jianhui, E-mail: sunjh@htu.cn [School of Environment, Henan Normal University, Key Laboratory for Yellow River and Huai River Water Environmental and Pollution Control, Ministry of Education, Henan Key Laboratory for Environmental Pollution Control, Xinxiang, Henan 453007 (China)

2015-06-05

Highlights: • A dual Bi-based ball-shaped material BiOF/Bi{sub 2}O{sub 3} were facilely synthesized. • The composition effect of BiOF/Bi{sub 2}O{sub 3}/RGO hybrid were probed for the first time. • The photocatalytic performances were evaluated upon natural sunlight irradiation. • The composites showed a twofold augmentation in the degradation efficiency. • The hybrid photocatalyst can be easily recycled for three times. - Abstract: A facile and efficient route for the controllable synthesis of BiOF/Bi{sub 2}O{sub 3} nanostructures by hydrolysis method was reported, where the as-prepared BiOF/Bi{sub 2}O{sub 3} was subsequently incorporated with reduced graphene oxide (RGO) sheets to form BiOF/Bi{sub 2}O{sub 3}/RGO composites. The obtained BiOF/Bi{sub 2}O{sub 3} and BiOF/Bi{sub 2}O{sub 3}/RGO composites were well characterized with the aid of various techniques to probe their crystallographic, morphological, chemical and optical properties. Photocatalytic capacities of the pure BiOF/Bi{sub 2}O{sub 3} and BiOF/Bi{sub 2}O{sub 3}/RGO composites have been investigated by the degradation of Rhodamine B (RhB)-contained wastewater under natural sunlight irradiation. A twofold augmentation of degradation efficiency was in turn observed for BiOF/Bi{sub 2}O{sub 3}/RGO composites compared with that of pure BiOF/Bi{sub 2}O{sub 3} under the natural sunlight irradiation. The optimum conditions, the effects of the active species and stabilities in photocatalytic performances of the BiOF/Bi{sub 2}O{sub 3}/RGO composites have also been probed.

Chemical purification of CaCO{sub 3} and CaWO{sub 4} powders used for CaWO{sub 4} crystal production for the CRESST experiment

Energy Technology Data Exchange (ETDEWEB)

Trinh Thi, H.H.; Defay, X.; Erb, A.; Hampf, R.; Lanfranchi, J.C.; Langenkaemper, A.; Morgalyuk, V.; Muenster, A.; Mondragon, E.; Oppenheimer, C.; Potzel, W.; Schoenert, S.; Steiger, H.; Ulrich, A.; Wawoczny, S.; Willers, M.; Zoeller, A. [Physik-Department and Excellence Cluster Universe, Technische Universitaet Muenchen, Garching (Germany)

2016-07-01

CRESST (Cryogenic Rare Event Search with Superconducting Thermometers) uses CaWO{sub 4} single crystals as targets for the direct search for dark matter particles. Since several years these CaWO{sub 4} crystals are grown at the Technische Universitaet Muenchen. Thereby, commercially available CaCO{sub 3} and WO{sub 3} powders are used for the synthesis of CaWO{sub 4} powder. For the experiment low intrinsic contaminations of the crystals play a crucial role. In order to improve the radiopurity of the crystals it is necessary to reduce potential sources for radioactive backgrounds such as U and Th. In this poster we will present our studies of the chemical purification of the CaCO{sub 3} and CaWO{sub 4} powders.

Synthesis and Characterization of Sn2+- based and Bi3+- based metal oxides for photocatalytic applications

KAUST Repository

Noureldine, Dalal

2016-07-01

The main challenge of water splitting technology is to develop stable, visible responsive photocatalysts that satisfy the thermodynamic requirements to achieve water redox reactions. This study investigates development of the semiconductors containing metals with s2d10 electronic configuration such as Sn2+ or Bi3+ which shifts the valence band position negatively. Efficient water splitting can, however, be only achieved by understanding the fundamental semiconductor properties of underlying processes. This work elucidates the semiconductor properties through two approaches: the first is to synthesize the materials of various stoichiometry in various forms (powders, thin film etc.) and the second is to perform a combined experimental-theoretical studies to determine the optoelectronic properties of the synthesized materials. The study includes the synthesis and characterization of a series of Bi3+ based semiconductors (Bi2Ti2O7, Bi12TiO20, and Bi4Ti3O12) to resolve inconsistencies in their optoelectronic properties. The crystal parameters and stoichiometry were confirmed by the Rietveld refinement and XRD measurements. These compounds showed a UV responsive absorption, high dielectric constants, and low electron and hole effective masses in one crystallographic reflecting their good charge separation and carrier diffusion properties. The approach showed to be accurate in determining the optoelectronic properties due to good agreement between experimental and theoretical values. The second study investigated the synthesis of SnNb2O6 and using flux assisted method which afforded control over the surface. Increasing the flux to reactant molar ratio resulted in a 2D platelets with anisotropic growth along bc plane as confirmed by XRD and SEM. The photocatalytic activity increased while increasing the flux to reactant ratio exceeding solid state synthesis. This method minimized the oxidation of the surface and formation of grain boundaries and enabled the synthesis of

Self-assembled Bi{sub 2}MoO{sub 6}/TiO{sub 2} nanofiber heterojunction film with enhanced photocatalytic activities

Energy Technology Data Exchange (ETDEWEB)

Li, Hua [School of Chemical Engineering, Northwest University, Xi’an 710069 (China); Zhang, Tianxi [School of Physics, Northwest University, Xi’an 710069 (China); Pan, Chao; Pu, Chenchen; Hu, Yang [School of Chemical Engineering, Northwest University, Xi’an 710069 (China); Hu, Xiaoyun [School of Physics, Northwest University, Xi’an 710069 (China); Liu, Enzhou, E-mail: liuenzhou@nwu.edu.cn [School of Chemical Engineering, Northwest University, Xi’an 710069 (China); Fan, Jun, E-mail: fanjun@nwu.edu.cn [School of Chemical Engineering, Northwest University, Xi’an 710069 (China)

2017-01-01

Highlights: • Self-assembled Bi{sub 2}MoO{sub 6}/TiO{sub 2} nanofiber film was synthesized. • TiO{sub 2} nanofiber film exhibits excellent visible light scattering property. • The scattering light from TiO{sub 2} overlaps with the absorption light of Bi{sub 2}MoO{sub 6}. • Bi{sub 2}MoO{sub 6}/TiO{sub 2} heterojunction photocatalysts show higher photocatalytic activity. - Abstract: TiO{sub 2} nanofiber film (TiO{sub 2} NFF) was successfully fabricated by an ethylene glycol-assisted hydrothermal method, and then self-assembled flake-like Bi{sub 2}MoO{sub 6} was grown on the surface of TiO{sub 2} nanofiber under alcohol thermal condition. The investigations indicate that the nanofiber structure of TiO{sub 2} films exhibits excellent visible light scattering property, the scattering light overlaps with the absorption band of Bi{sub 2}MoO{sub 6}, which can enhance the utility of incident light. The prepared Bi{sub 2}MoO{sub 6}/TiO{sub 2} composites show obviously enhanced photocatalytic activity for methylene blue (MB) degradation compared with pure TiO{sub 2} nanofiber under visible light irradiation (λ > 420 nm). The enhanced photocatalytic activity is primarily attributed to the synergistic effect of visible light absorption and effective electron-hole separation at the interfaces of the two semiconductors, which is confirmed by photoluminescence (PL) and electrochemical tests.

Fabrication of flower-like direct Z-scheme β-Bi2O3/g-C3N4 photocatalyst with enhanced visible light photoactivity for Rhodamine B degradation

Science.gov (United States)

Zhang, Liping; Wang, Guohong; Xiong, Zhenzhong; Tang, Hua; Jiang, Chuanjia

2018-04-01

A combined hydrothermal-calcination approach is developed to synthesize hierarchical β-Bi2O3/g-C3N4 direct Z-scheme photocatalyst with enhanced visible light photoactivity for Rhodamine B (RhB) degradation. First, Bi2O2CO3 microflowers were hydrothermally prepared using Bi(NO3)3·5H2O as feedstocks, and then a series of β-Bi2O3/g-C3N4 direct Z-scheme photocatalysts were synthesized via a facile calcination method using Bi2O2CO3 and g-C3N4 as precursors. The samples were systematically characterized by various characterization technologies including X-ray diffraction, scanning and transmission electron microscopes, Fourier transform infrared spectroscopy and N2 absorption-desorption equipment. It was found that the g-C3N4 content in the precursors played a key role in affecting the photocatalytic activity of the final products. The β-Bi2O3/g-C3N4 heterojunction exhibited higher photocatalytic activity than single active components (β-Bi2O3 and g-C3N4), indicating the presence of a synergistic effect between two active components in β-Bi2O3/g-C3N4 heterojunction. Among all as-prepared catalysts, the 70 wt.% g-C3N4/Bi2O2CO3 exhibits the highest activity for RhB degradation, and the apparent reaction rate constant k (42.2 × 10-3 min-1) is 3.1 and 1.7 times as high as that of pure β-Bi2O3 (13.5 × 10-3 min-1) and g-C3N4 (25.2 × 10-3 min-1), respectively. The enhanced photocatalytic performance of β-Bi2O3/g-C3N4 heterostructure photocatalysts is mainly due to the high surface area, closely contacted interfaces between the β-Bi2O3 and g-C3N4 component, and the formation of direct Z-scheme structure in the β-Bi2O3/g-C3N4 composites.

Synthesis, characterization and photocatalytic activity of WO{sub 3}/TiO{sub 2} for NO removal under UV and visible light irradiation

Energy Technology Data Exchange (ETDEWEB)

Luévano-Hipólito, E. [CIIDIT, Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico); Martínez-de la Cruz, A., E-mail: azael.martinezdl@uanl.edu.mx [CIIDIT, Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico); López-Cuellar, E. [CIIDIT, Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico); Yu, Q.L.; Brouwers, H.J.H. [Department of the Built Environment, Eindhoven University of Technology, P.O. Box 513, 5600 MB Eindhoven (Netherlands)

2014-11-14

Samples with different proportions WO{sub 3}/TiO{sub 2} were prepared by co-precipitation method followed by a heat treatment. The samples were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS), and adsorption–desorption N{sub 2} isotherms (BET). The photocatalytic properties of WO{sub 3}/TiO{sub 2} samples were evaluated in the photo-oxidation reaction of nitric oxide (NO) under UV and visible light irradiation. The highest photocatalytic activity was observed in the WO{sub 3}/TiO{sub 2} sample with a composition of 80% mole of TiO{sub 2}. Among the different substrates used for supporting the photocatalyst, the best results were reached over concrete and glass when it was exposed to UV and visible light irradiation, respectively. In overall, the photocatalytic efficiency of the synthesized materials was higher under UV than visible light irradiation. - Highlights: • WO{sub 3}/TiO{sub 2} prepared in simple way show high photocatalytic activity for NO removal. • The concrete was the best substrate to the performance of WO{sub 3}/TiO{sub 2} with UV radiation. • The glass was the best substrate to the performance of WO{sub 3}/TiO{sub 2} with visible radiation.

Highly efficient photocatalytic conversion of solar energy to hydrogen by WO3/BiVO4 core-shell heterojunction nanorods

Science.gov (United States)

Kosar, Sonya; Pihosh, Yuriy; Bekarevich, Raman; Mitsuishi, Kazutaka; Mawatari, Kazuma; Kazoe, Yutaka; Kitamori, Takehiko; Tosa, Masahiro; Tarasov, Alexey B.; Goodilin, Eugene A.; Struk, Yaroslav M.; Kondo, Michio; Turkevych, Ivan

2018-04-01

Photocatalytic splitting of water under solar light has proved itself to be a promising approach toward the utilization of solar energy and the generation of environmentally friendly fuel in a form of hydrogen. In this work, we demonstrate highly efficient solar-to-hydrogen conversion efficiency of 7.7% by photovoltaic-photoelectrochemical (PV-PEC) device based on hybrid MAPbI3 perovskite PV cell and WO3/BiVO4 core-shell nanorods PEC cell tandem that utilizes spectral splitting approach. Although BiVO4 is characterized by intrinsically high recombination rate of photogenerated carriers, this is not an issue for WO3/BiVO4 core-shell nanorods, where highly conductive WO3 cores are combined with extremely thin absorber BiVO4 shell layer. Since the BiVO4 layer is thinner than the characteristic carrier diffusion length, the photogenerated charge carriers are separated at the WO3/BiVO4 heterojunction before their recombination. Also, such architecture provides sufficient optical thickness even for extremely thin BiVO4 layer due to efficient light trapping in the core-shell WO3/BiVO4 nanorods with high aspect ratio. We also demonstrate that the concept of fill factor can be used to compare I-V characteristics of different photoanodes regarding their optimization for PV/PEC tandem devices.

Broad band and enhanced photocatalytic behaviour of Ho3+-doped Bi2O3 micro-rods

Science.gov (United States)

Prasad, Neena; Karthikeyan, Balasubramanian

2018-06-01

Band-gap-tuned Bi2O3 micro-rods were synthesized using simple co-precipitation method by doping 5 wt% Ho3+ to mitigate the concentration of toxic dye from the polluted water using it as a photocatalyst. Structure and morphology of the prepared samples were identified using powder X-ray diffraction technique and scanning electron microscopy (SEM). Elemental composition and chemical state of the prepared samples were analyzed from the X-ray photoelectron spectroscopy (XPS). Considerable absorption in IR region was observed for Ho3+ doped Bi2O3 due to the electronic transitions of 5I8→5F4, 5I8→5F5, and 5I8→5I5, 5I6. The excellent ultra-violet (UV), white and infrared light (IR)-driven photocatalytic activity were suggested for pure and doped Bi2O3 samples. Ho3+-doped Bi2O3 micro-rods exhibits a better photocatalytic activity under white light irradiation. The consequence of the bandgap and the synergetic effect of Ho3+ and Bi2O3 on the photocatalytic degradation of MB were investigated.

Development of MnBi permanent magnet: Neutron diffraction of MnBi powder

Energy Technology Data Exchange (ETDEWEB)

Cui, J., E-mail: jun.cui@pnnl.gov; Choi, J. P.; Li, G.; Polikarpov, E.; Darsell, J. [Energy and Environment Directorate, Pacific Northwest National Laboratory, Richland, Washington 99354 (United States); Kramer, M. J.; Zarkevich, N. A.; Wang, L. L.; Johnson, D. D. [Materials Sciences and Engineering Division, Ames Laboratory, Ames, Iowa 50011 (United States); Marinescu, M. [Electron Energy Corporation, Landisville, Pennsylvania 17538 (United States); Huang, Q. Z.; Wu, H. [NIST Center for Neutron Research, National Institute of Standards and Technology, Gaithersburg, Maryland 20899-6102 (United States); Vuong, N. V.; Liu, J. P. [Department of Physics, University of Texas at Arlington, Arlington, Texas 76019 (United States)

2014-05-07

MnBi attracts great attention in recent years for its great potential as permanent magnet materials. MnBi phase is difficult to obtain because of the rather drastic peritectic reaction between Mn and Bi. In this paper, we report our effort on synthesizing high purity MnBi compound using conventional powder metallurgical approaches. Neutron diffraction was carried out to investigate the crystal and nuclear structure of the obtained powder. The result shows that the purity of the obtained powder is about 91 wt. % at 300 K, and the magnetic moment of the Mn atom in MnBi lattice is 4.424 and 4.013 μ{sub B} at 50 K and 300 K, respectively.

Development of MnBi permanent magnet: Neutron diffraction of MnBi powder

Energy Technology Data Exchange (ETDEWEB)

Cui, J; Choi, JP; Li, G; Polikarpov, E; Darsell, J; Kramer, MJ; Zarkevich, NA; Wang, LL; Johnson, DD; Marinescu, M; Huang, QZ; Wu, H; Vuong, NV; Liu, JP

2014-05-07

MnBi attracts great attention in recent years for its great potential as permanent magnet materials. MnBi phase is difficult to obtain because of the rather drastic peritectic reaction between Mn and Bi. In this paper, we report our effort on synthesizing high purity MnBi compound using conventional powder metallurgical approaches. Neutron diffraction was carried out to investigate the crystal and nuclear structure of the obtained powder. The result shows that the purity of the obtained powder is about 91 wt. % at 300 K, and the magnetic moment of the Mn atom in MnBi lattice is 4.424 and 4.013 mu(B) at 50 K and 300 K, respectively. (C) 2014 AIP Publishing LLC.

Three-dimensional Ag2O/Bi5O7I p-n heterojunction photocatalyst harnessing UV-vis-NIR broad spectrum for photodegradation of organic pollutants.

Science.gov (United States)

Chen, Yannan; Zhu, Gangqiang; Hojamberdiev, Mirabbos; Gao, Jianzhi; Zhu, Runliang; Wang, Chenghui; Wei, Xiumei; Liu, Peng

2018-02-15

Ag 2 O nanoparticles-loaded Bi 5 O 7 I microspheres forming a three dimensional Ag 2 O/Bi 5 O 7 I p-n heterojunction photocatalyst with wide-spectrum response were synthesized in this study. The results of transmission electron microscopy observations revealed that the Ag 2 O nanoparticles with the diameter of ca. 10-20nm were distributed on the surfaces of Bi 5 O 7 I nanosheets. The as-synthesized Ag 2 O/Bi 5 O 7 I exhibited an excellent wide-spectrum response to wavelengths ranging from ultraviolet (UV) to near-infrared (NIR), indicating its potential for effective utilization of solar energy. Compared with pure Bi 5 O 7 I, the Ag 2 O/Bi 5 O 7 I composite also demonstrated excellent photocatalytic activity for the degradation of Bisphenol A and phenol in aqueous solution under visible LED light irradiation. Among samples, the 20% Ag 2 O/Bi 5 O 7 I composite photocatalyst showed the highest photocatalytic activity for the degradation of Bisphenol A and phenol in aqueous solution. In addition, the 20% Ag 2 O/Bi 5 O 7 I composite also exhibited a photocatalytic activity for the degradation of Bisphenol A under NIR light irradiation. The improved photocatalytic activity is attributed to the formation of a p-n heterojunction between Ag 2 O and Bi 5 O 7 I, allowing the efficient utilization of solar energy (from UV to NIR) and high separation efficiency of photogenerated electron-hole pairs. The present work is desirable to explore a possible avenue for the full utilization of solar energy. Copyright © 2017 Elsevier B.V. All rights reserved.

Preparation, optical, and photocatalytic studies of defect pyrochlores: KCr{sub 0.33}W{sub 1.67}O{sub 6} and A{sub x}Cr{sub 0.33}W{sub 1.67}O{sub 6}{center_dot}nH{sub 2}O

Energy Technology Data Exchange (ETDEWEB)

Ravi, G.; Veldurthi, Naveen Kumar [Osmania University, Department of Chemistry (India); Prasad, Muvva D. [University of Hyderabad, School of Chemistry (India); Muniratnam, N. R. [Centre for Materials Electronics Technology (C-MET) (India); Prasad, G. [Osmania University, Department of Physics (India); Vithal, M., E-mail: mugavithal@gmail.com [Osmania University, Department of Chemistry (India)

2013-09-15

Nano sized defect pyrochlores of compositions KCr{sub 0.33}W{sub 1.67}O{sub 6} and A{sub x}Cr{sub 0.33}W{sub 1.67}O{sub 6}{center_dot}nH{sub 2}O (A = Sn, Ag, Bi, Sm, Eu, and Gd) have been synthesized by sol-gel and ion exchange methods, respectively. These oxides were characterized by thermogravimetric analysis, powder X-ray diffraction, energy dispersive spectra, transmission electron microscopy, UV-Vis diffuse reflectance spectra, Raman spectra, and Fourier transform infrared spectra. Spontaneous exchange of K{sup +} with A ion is accompanied by insertion of water also into the lattice. KCr{sub 0.33}W{sub 1.67}O{sub 6} and A{sub x}Cr{sub 0.33}W{sub 1.67}O{sub 6}{center_dot}nH{sub 2}O crystallize in cubic lattice and isomorphous with KSbWO{sub 6}. The optical properties of Cr{sup 3+} were investigated. Substitution of K{sup +} by A ion leads to a shift of absorption onset to longer wavelengths marginally. The Raman spectra of all the samples are characteristic of defect pyrochlore system. The photocatalytic degradation of methylene blue aqueous solution was investigated using these oxides. The results obtained were fitted with the Langmuir-Hinshelwood model to study the degradation kinetics. Both Sn{sup 2+} and Bi{sup 3+}-doped KCr{sub 0.33}W{sub 1.67}O{sub 6} exhibit higher photoactivity in the degradation of methylene blue. The structure/composition of the photocatalyst remains the same even after fourth cycle of photodegradation.

Constructing 2D layered MoS2 nanosheets-modified Z-scheme TiO2/WO3 nanofibers ternary nanojunction with enhanced photocatalytic activity

Science.gov (United States)

Zhao, Jiangtao; Zhang, Peng; Fan, Jiajie; Hu, Junhua; Shao, Guosheng

2018-02-01

Advanced materials for photoelectrochemical H2 production are important to the field of renewable energy. Despite great efforts have been made, the present challenge in materials science is to explore highly active photocatalysts for splitting of water at low cost. In this work, we report a new composite material consisting of 2D layered MoS2 nanosheets grown on the presence of TiO2/WO3 nanofibers (TW) as a high-performance photocatalyst for H2 evolution. This composite material was prepared by a two-step simple process of electrospinning and hydrothermal. We found that the as-prepared TiO2/WO3@MoS2 (TWM) hybrid exhibited superior photocatalytic activity in the hydrogen evolution reaction (HER) even without the noble metal-cocatalyst. Importantly, the TiO2/WO3@MoS2 heterostructure with 60 wt% of MoS2 exhibits the highest hydrogen production rate. This great improvement is attributed to the positive synergetic effect between the WO3 and MoS2 components in this hybrid cocatalyst, which serve as hole collector and electron collector, respectively. Moreover, the effective charge separation was directly proved by ultraviolet photoelectron spectroscopy, electrochemical impedance spectroscopy, and photocurrent analysis.

Enhanced photoelectrochemical and photocatalytic activity of WO3-surface modified TiO2 thin film

Science.gov (United States)

Qamar, Mohammad; Drmosh, Qasem; Ahmed, Muhammad I.; Qamaruddin, Muhammad; Yamani, Zain H.

2015-02-01

Development of nanostructured photocatalysts for harnessing solar energy in energy-efficient and environmentally benign way remains an important area of research. Pure and WO3-surface modified thin films of TiO2 were prepared by magnetron sputtering on indium tin oxide glass, and photoelectrochemical and photocatalytic activities of these films were studied. TiO2 particles were <50 nm, while deposited WO3 particles were <20 nm in size. An enhancement in the photocurrent was observed when the TiO2 surface was modified WO3 nanoparticles. Effect of potential, WO3 amount, and radiations of different wavelengths on the photoelectrochemical activity of TiO2 electrodes was investigated. Photocatalytic activity of TiO2 and WO3-modified TiO2 for the decolorization of methyl orange was tested.

Polymorphism of tungsten perovskite compounds Ba/sub 2/SEsub(0. 67)WO/sub 6/

Energy Technology Data Exchange (ETDEWEB)

Schittenhelm, H J; Kemmler-Sack, S [Tuebingen Univ. (F.R. Germany). Inst. fuer Anorganische Chemie

1976-09-01

The compounds Ba/sub 2/SEsub(0.67)WO/sub 6/ with SE = Gd-Lu are polymorphic. Above 1200/sup 0/C the instable cubic modification (ordered perovskite with 4 formula units Ba/sub 2/SEsub(0.67)vacantsub(0.33)WO/sub 6/ per cell) transforms irreversibly into a hexagonal modification with completely filled cationic lattice. For Ba/sub 2/Eusub(0.67)WO/sub 6/ the transformation is incomplete. With SE = Nd and Sm only the cubic modification is formed.

Investigations on Bi25FeO40 powders synthesized by hydrothermal and combustion-like processes

International Nuclear Information System (INIS)

Köferstein, Roberto; Buttlar, Toni; Ebbinghaus, Stefan G.

2014-01-01

The syntheses of phase-pure and stoichiometric iron sillenite (Bi 25 FeO 40 ) powders by a hydrothermal (at ambient pressure) and a combustion-like process are described. Phase-pure samples were obtained in the hydrothermal reaction at 100 °C (1), whereas the combustion-like process leads to pure Bi 25 FeO 40 after calcination at 750 °C for 2 h (2a). The activation energy of the crystallite growth process of hydrothermally synthesized Bi 25 FeO 40 was calculated as 48(9) kJ mol −1 . The peritectic point was determined as 797(1) °C. The optical band gaps of the samples are between 2.70(7) eV and 2.81(6) eV. Temperature and field-depending magnetization measurements (5−300 K) show a paramagnetic behaviour with a Curie constant of 55.66×10 −6 m 3 K mol −1 for sample 1 and C=57.82×10 −6 m 3 K mol −1 for sample 2a resulting in magnetic moments of µ mag =5.95(8) µ B mol −1 and µ mag =6.07(4) µ B mol −1 . The influence of amorphous iron-oxide as a result of non-stoichiometric Bi/Fe ratios in hydrothermal syntheses on the magnetic behaviour was additionally investigated. - Graphical abstract: Bi 25 FeO 40 powders were prepared by a hydrothermal method and a combustion process. The optical band gaps and the peritectic point were determined. The magnetic behaviour was investigated depending on the synthesis and the initial Bi/Fe ratios. The influence of amorphous iron-oxide on the magnetic properties was examined. - Highlights: • Two simple syntheses routes for stoichiometric Bi 25 FeO 40 powders using starch as polymerization agent. • Monitoring the phase evolution and crystallite growth kinetics during the syntheses. • Determination of the optical band gap and melting point. • Investigations of the magnetic behaviour of Bi 25 FeO 40 powders. • Influence of amorphous iron oxide and a non-stoichiometric Bi/Fe ratio on the magnetic behaviour

Room-temperature in situ fabrication of Bi2O3/g-C3N4 direct Z-scheme photocatalyst with enhanced photocatalytic activity

Science.gov (United States)

He, Rongan; Zhou, Jiaqian; Fu, Huiqing; Zhang, Shiying; Jiang, Chuanjia

2018-02-01

Constructing direct Z-scheme heterojunction is an effective approach to separating photogenerated charge carriers and improving the activity of semiconductor photocatalysts. Herein, a composite of bismuth(III) oxide (Bi2O3) and graphitic carbon nitride (g-C3N4) was in situ fabricated at room temperature by photoreductive deposition of Bi3+ and subsequent air-oxidation of the resultant metallic Bi. Quantum-sized ω-Bi2O3 nanoparticles approximately 6 nm in diameter were uniformly distributed on the surface of mesoporous g-C3N4. The as-prepared Bi2O3/g-C3N4 composite exhibited higher photocatalytic activity than pure Bi2O3 and g-C3N4 for photocatalytic degradation of phenol under visible light. Reactive species trapping experiments revealed that superoxide radicals and photogenerated holes played important roles in the photocatalytic degradation of phenol. The enhanced photocatalytic activity, identification of reactive species and higher rate of charge carrier recombination (as indicated by stronger photoluminescence intensity) collectively suggest that the charge migration within the Bi2O3/g-C3N4 composite followed a Z-scheme mechanism. Photogenerated electrons on the conduction band of Bi2O3 migrate to the valence band of g-C3N4 and combine with photogenerated holes therein. At the cost of these less reactive charge carriers, the Z-scheme heterojunction enables efficient charge separation, while preserving the photogenerated electrons and holes with stronger redox abilities, which is beneficial for enhanced photocatalytic activity.

Hydrothermal Synthesis, Characterization, and Optical Properties of Ce Doped Bi2MoO6 Nanoplates

Directory of Open Access Journals (Sweden)

Anukorn Phuruangrat

2014-01-01

Full Text Available Undoped and Ce doped Bi2MoO6 samples were synthesized by hydrothermal reaction at 180°C for 20 h. Phase, morphology, atomic vibration, and optical properties were characterized by X-ray powder diffraction (XRD, X-ray photoelectron spectroscopy (XPS, Raman spectrophotometry, Fourier transform infrared (FTIR spectroscopy, scanning electron microscopy (SEM, transmission electron microscopy (TEM, selected area electron diffraction (SAED, and UV-visible spectroscopy. In this research, the products were orthorhombic Bi2MoO6 nanoplates with the growth direction along the [0b0], including the asymmetric and symmetric stretching and bending modes of Bi–O and Mo–O. Undoped and Ce doped Bi2MoO6 samples show a strong absorption in the UV region.

Bismuth zinc vanadate, BiZn2VO6: New crystal structure type and electronic structure

International Nuclear Information System (INIS)

Eliziario Nunes, Sayonara; Wang, Chun-Hai; So, Karwei; Evans, John S.O.; Evans, Ivana Radosavljević

2015-01-01

We report a combined experimental and computational study of the crystal structure and electronic properties of bismuth zinc vanadate, BiZn 2 VO 6 , known for its visible light photocatalytic activity. The crystal structure has been solved from laboratory powder X-ray diffraction data using the repeated minimisations from random starting values method. BiZn 2 VO 6 adopts a new structure type, based on the following building blocks: corner- and edge-sharing ZnO 4 tetrahedra, ZnO 6 octahedra and VO 4 tetrahedra, and Bi 2 O 12 dimers. It is the only known member of the BiM 2 AO 6 (M=Pb, Ca, Cd, Mn, Zn, Mg, Cu; A=V, P, As) family which does not appear to be structurally closely related to others. The electronic structure of BiZn 2 VO 6 , calculated by DFT methods, shows that it is an indirect gap semiconductor with a calculated band gap of 1.6 eV, which compares favourably to the experimentally measured value of 2.4 eV. - Graphical abstract: The crystal structure of BiZn 2 VO 6 , a new structure type in the BiM 2 AO 6 (M=Mg, Ca, Cd, Cu, Pb, Mn, Zn; A=V, P, As) family. - Highlights: • Structure solution from PXRD data by repeated minimisations from random starting values. • New structure type in the BiM 2 AO 6 (M=Pb, Ca, Cd, Mn, Zn, Mg, Cu; A=V, P, As) family. • Electronic structure calculation

Fabricaion of improved novel p–n junction BiOI/Bi{sub 2}Sn{sub 2}O{sub 7} nanocomposite for visible light driven photocatalysis

Energy Technology Data Exchange (ETDEWEB)

Xu, Weicheng [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Fang, Jianzhang, E-mail: fangjzh@scnu.edu.cn [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Guangdong Technology Research Center for Ecological Management and Remediation of Urban Water System, Guangzhou 510006 (China); Zhu, Ximiao [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Fang, Zhanqiang [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Guangdong Technology Research Center for Ecological Management and Remediation of Urban Water System, Guangzhou 510006 (China); Cen, Chaoping [The Key Laboratory of Water and Air Pollution Control of Guangdong Province, South China Institute of Environmental Sciences, Guangzhou 510655 (China)

2015-12-15

Graphical abstract: - Highlights: • A p–n heterojunction photocatalyst BiOI/Bi{sub 2}Sn{sub 2}O{sub 7} was prepared by hydrothermal method. • 4% BiOI/Bi{sub 2}Sn{sub 2}O{sub 7} with maximal photocatalytic degradation efficiency (RhB) of 99.9%. • A specific degradation routes of RhB was illustrated. • The photocatalytic mechanism is discussed according to p–n junction principles. • • O{sub 2}{sup −} and h+ are the main reactive species for the degradation of RhB. - Abstract: A series of novel p−n junction photocatalysts BiOI/Bi{sub 2}Sn{sub 2}O{sub 7} (BiOI/BSO) were successfully fabricated via a facile hydrothermal method. The phase structures, morphologies and optical properties of the as-prepared samples were studied by XRD, TEM, HRTEM, BET, XPS, UV–vis DRS and photoluminescence (PL) spectroscopy. The results showed that BiOI/BSO heteronanostructures displayed much higher photocatalytic activity than pure BSO and BiOI for the degradation of rhodamine B (RhB). The best photocatalytic activity of BiOI/BSO with almost 99.9% RhB degradation situated at molar percentage ratio of 4% after 6 h irradiation. The enhanced photocatalytic performance of BiOI/BSO could be mainly attributed to the formation of the heterojunction between p-BiOI and n-BSO, which effectively restrains the recombination of photoinduced electron–hole pairs. Moreover, the study of radical scavengers affirmed that h{sup +} and • O{sub 2}{sup −} were the primary reactive species for the degradation of RhB.

Enhanced visible-light-response photocatalytic degradation of methylene blue on Fe-loaded BiVO4 photocatalyst

International Nuclear Information System (INIS)

Chala, Sinaporn; Wetchakun, Khatcharin; Phanichphant, Sukon; Inceesungvorn, Burapat; Wetchakun, Natda

2014-01-01

Highlights: • Fe-loaded BiVO 4 particles were prepared by hydrothermal method. • Physicochemical properties played a significant role in photocatalytic process. • All Fe-loaded BiVO 4 samples showed higher photocatalytic activity than pure BiVO 4 . • The Fe 3+ ions may improve the separation of photogenerated electrons and holes. - Abstract: Pure BiVO 4 and nominal 0.5–5.0 mol% Fe-loaded BiVO 4 samples were synthesized by hydrothermal method. All samples were characterized in order to obtain the correlation between structure and photocatalytic properties by X-ray diffraction, Brunauer, Emmett and Teller, UV–vis diffuse reflectance spectrophotometry, photoluminescence spectroscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and inductively coupled plasma-optical emission spectroscopy. The structure of all samples was single-phase monoclinic scheelite. The absorption spectrum of 5.0 mol% Fe-loaded BiVO 4 shifted to the visible region, suggesting the potential application of this material as a superior visible-light driven photocatalyst in comparison with pure BiVO 4 . Photocatalytic activities of all photocatalyst samples were examined by studying the degradation of methylene blue under visible light irradiation. The results clearly showed that Fe-loaded BiVO 4 sample exhibited remarkably higher activity than pure BiVO 4

In situ loading of Ag{sub 2}WO{sub 4} on ultrathin g-C{sub 3}N{sub 4} nanosheets with highly enhanced photocatalytic performance

Energy Technology Data Exchange (ETDEWEB)

Li, Yunfeng; Jin, Renxi; Fang, Xu; Yang, Yang; Yang, Man; Liu, Xianchun [Jilin Provincial Key Laboratory of Advanced Energy Materials, Department of Chemistry, Northeast Normal University, Changchun 130024 (China); Xing, Yan, E-mail: xingy202@nenu.edu.cn [Jilin Provincial Key Laboratory of Advanced Energy Materials, Department of Chemistry, Northeast Normal University, Changchun 130024 (China); Song, Shuyan [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China)

2016-08-05

Graphical abstract: Ultrathin g-C{sub 3}N{sub 4} nanosheets (g-C{sub 3}N{sub 4}−NS) with improved electron transport ability and large number of active sites are employed instead of bulk g-C{sub 3}N{sub 4} to prepare the Ag{sub 2}WO{sub 4}/g-C{sub 3}N{sub 4}−NS heterostructured photocatalysts, which exhibit remarkable photocatalytic activity for wastewater treatment. - Highlights: • Ag2WO4/g-C3N4-NS photocatalysts were obtained by a deposition-precipitation method. • Ag2WO4/g-C3N4-NS possess large surface areas and increased lifetime of charges. • Ag2WO4/g-C3N4-NS exhibit enhanced activity on degradation of RhB and MO. • The photocatalytic mechanism of the Ag2WO4/g-C3N4-NS system were investigated. - Abstract: The g-C{sub 3}N{sub 4} nanosheets (g-C{sub 3}N{sub 4}−NS) exhibit more excellent property than common bulk g-C{sub 3}N{sub 4} (g-C{sub 3}N{sub 4}-B) due to their large surface areas, improved electron transport ability and well dispersion in water. In this work, ultrathin g-C{sub 3}N{sub 4}−NS with a thickness of about 2.7 nm have been synthesized by a simple thermal exfoliation of bulk g-C{sub 3}N{sub 4}, and then Ag{sub 2}WO{sub 4} nanoparticles are in situ loaded on their surface to construct the Ag{sub 2}WO{sub 4}/g-C{sub 3}N{sub 4}−NS heterostructured photocatalysts. Due to their unique physicochemical properties, the as-prepared heterostructures possess a fast interfacial charge transfer and increased lifetime of photo-excited charge carriers, and exhibit much higher photocatalytic activity. Under visible light irradiation, the optimum photocatalytic activity of Ag{sub 2}WO{sub 4}/g-C{sub 3}N{sub 4}−NS composites is almost 53.6 and 26.5 times higher than that of pure g-C{sub 3}N{sub 4}-B and Ag{sub 2}WO{sub 4}/g-C{sub 3}N{sub 4}-B heterostructures towards the degradation of rhodamine B, respectively, and is almost 30.6 and 9.8 times higher towards the degradation of methyl orange, respectively. In addition, the natural sunlight

Preparation and characterization of tungsten-loaded titanium dioxide photocatalyst for enhanced dye degradation

International Nuclear Information System (INIS)

Saepurahman; Abdullah, M.A.; Chong, F.K.

2010-01-01

Tungsten-loaded TiO 2 photocatalyst has been successfully prepared and characterized. TEM analysis showed that the photocatalysts were nanosize with the tungsten species forming layers of coverage on the surface of TiO 2 , but not in clustered form. This was confirmed by XRD and FT-Raman analyses where tungsten species were well dispersed at lower loading ( 3 at higher loadings (>12 mol%). In addition, loading with tungsten could stabilize the anatase phase from transforming into inactive rutile phase and did not shift the optical absorption to the visible region as shown by DRUV-vis analysis. PZC value of TiO 2 was found at 6.4, but the presence of tungsten at 6.5 mol% WO 3 , decreased the PZC value to 3. Tungsten-loaded TiO 2 was superior to unmodified TiO 2 with 2-fold increase in degradation rate of methylene blue, and equally effective for the degradation of different class of dyes such as methyl violet and methyl orange at 1 mol% WO 3 loading.

Enhanced photocatalytic activity of Te-doped Bi{sub 2}MoO{sub 6} under visible light irradiation: Effective separation of photogenerated carriers resulted from inhomogeneous lattice distortion and improved electron capturing ability

Energy Technology Data Exchange (ETDEWEB)

Chen, Shuguang, E-mail: csustcsg@yahoo.com; Li, Yuhan; Wu, Zixu; Wu, Baoxin; Li, Haibin; Li, Fujin

2017-05-15

Te-doped Bi{sub 2}MoO{sub 6} photocatalyst was hydrothermally synthesized, and nonmetal atoms Te were homogeneously incorporated into Bi{sub 2}MoO{sub 6} lattice with the substitution of Te{sup 4+} to Mo{sup 6+}. With increasing Te-doping concentration in Bi{sub 2}MoO{sub 6}, no detectable band-gap narrowing but more and more severe inhomogeneous lattice distortions were determined. The activity of Bi{sub 2}MoO{sub 6} photocatalyst was evaluated through methylene blue degradation under visible light irradiation (λ>410 nm) and was greatly enhanced by Te-doping. When Te-doped Bi{sub 2}MoO{sub 6} was synthesized at Te/Mo molar ratio of 7.5%, a maximum first-order rate constant of methylene blue degradation was obtained. The inhomogeneous lattice distortion generated an internal dipole moment, and the holes generated with the substitution of Te{sup 4+} to Mo{sup 6+} acted as the capturing centers of photogenerated electrons, thus the effective separation of photogenerated carriers was facilitated to result in a relatively high concentration of holes on the surface of Te-doped Bi{sub 2}MoO{sub 6} to be favorable for the efficient methylene blue degradation. - Graphical abstract: With the substitution of Te{sup 4+} to Mo{sup 6+}, effective separation of photogenerated carriers resulted from inhomogeneous lattice distortion and improved electron capturing ability is achieved to be responsible for enhanced photocatalytic activity of Te-doped Bi{sub 2}MoO{sub 6}. - Highlights: • Nonmetal Te is incorporated into Bi{sub 2}MoO{sub 6} with the substitution of Te{sup 4+} to Mo{sup 6+}. • Revealing inhomogeneous lattice distortion and improved electron capturing ability. • Effective separation of photogenerated carriers in Te-doped Bi{sub 2}MoO{sub 6} is achieved. • The mechanism of methylene blue degradation over Te-doped Bi{sub 2}MoO{sub 6} is proposed.

Ag doped (Bi1.6Pb0.4Sr2CaCu2O8+δ textured rods

Directory of Open Access Journals (Sweden)

Díez, J. C.

2008-06-01

Full Text Available In this work, superconducting samples of (Bi1.6Pb0.4Sr2CaCu2O8+δ with Ag additions have been studied. (Bi1.6Pb0.4Sr2CaCu2O8+δ + x wt.% Ag (with x = 0, 1 and 3 powders were synthesized using a sol-gel method. The obtained powders were used as precursors to fabricate long textured cylindrical bars through a floating zone melting method. A drastic change on the microstructure has been found when comparing with undoped Bi2Sr2CaCu2O8+δ samples. The results showed that electrical resistivity at room temperature, critical current as well as flexural strength are improved when Ag is added to these Pb doped samples, while critical temperature does not change. On the other hand, it has been found that samples with composition (Bi1.6Pb0.4Sr2CaCu2O8+δ + Ag shown E-I curves with very high sharpness values on the zone of the superconducting to normal transition, reaching n-values (E∼In as high as 45 at 65K.Se han preparado polvos cerámicos de composición (Bi1.6Pb0.4Sr2CaCu2O8+δ + x % Ag en peso (con x = 0, 1 y 3 mediante un proceso sol-gel. Estos polvos se han utilizado para fabricar precursores que se texturaron por medio del método de fusión zonal flotante. Se ha encontrado un gran cambio en la microestructura cuando se compara con muestras de composición pura Bi2Sr2CaCu2O8+δ. Tanto la resistividad eléctrica a temperatura ambiente, como la corriente crítica, así como la resistencia a flexión se mejoran cuando la Ag se adiciona a estas muestras dopadas con Pb, mientras que no se observa cambio en la temperatura crítica. Por otra parte, se ha encontrado que las muestras de composición (Bi1.6Pb0.4Sr2CaCu2O8+δ + Ag presentan una gran pendiente de la curva E-I en la zona de transición entre el estado superconductor y el estado normal. Con estas composiciones, se han encontrado valores de n (E∼In de hasta 45 a 65K.

Rapid formation of phase-clean 110 K (Bi-2223) powders derived via freeze-drying process

Science.gov (United States)

Balachandran, U.

1996-06-04

A process for the preparation of amorphous precursor powders for Pb-doped Bi{sub 2}Sr{sub 2} Ca{sub 2}Cu{sub 3}O{sub x} (2223) includes a freeze-drying process incorporating a splat-freezing step. The process generally includes splat freezing a nitrate solution of Bi, Pb, Sr, Ca, and Cu to form flakes of the solution without any phase separation; grinding the frozen flakes to form a powder; freeze-drying the frozen powder; heating the dried powder to form a dry green precursor powders; denitrating the green-powders; heating the denitrated powders to form phase-clean Bi-2223 powders. The grain boundaries of the 2223 grains appear to be clean, leading to good intergrain contact between 2223 grains. 11 figs.

Negative thermal expansion in Sc2(WO4)3

International Nuclear Information System (INIS)

Evans, J.S.O.; Mary, T.A.; Sleight, A.W.

1998-01-01

Sc 2 (WO 4 ) 3 has been found to show the highly unusual property of negative thermal expansion over a temperature range of 10 to 1,073 K. Powder neutron diffraction data from 10 to 450 K shows an essentially linear decrease in cell volume as a function of temperature. The intrinsic linear coefficient of thermal expansion from this data is -2.2 x 10 -6 K -1 . The linear coefficient of thermal expansion measured on a ceramic bar of Sc 2 (WO 4 ) 3 can be as negative as -11 x 10 -6 K -1 due to microstructure changes as a function of temperature. Rietveld refinement as a function of temperature suggests that the intrinsic negative thermal expansion can be related to transverse vibrations of bridging oxygen atoms in the structure. The anharmonic nature of these vibrations leads to a coupled tilting of the quasi-rigid framework polyhedra. This tilting in turn causes the structure to become more dense with increasing temperature

Au/BiOCl heterojunction within mesoporous silica shell as stable plasmonic photocatalyst for efficient organic pollutants decomposition under visible light

International Nuclear Information System (INIS)

Yan, Xiaoqing; Zhu, Xiaohui; Li, Renhong; Chen, Wenxing

2016-01-01

Highlights: • A heterojunction of Au/BiOCl was fabricated within the mesoporous silica shell. • The compact contact between Au and BiOCl enables electrons back flow from Au to BiOCl. • Au/BiOCl@mSiO 2 plasmonic photocatalyst shows efficient visible light photoactivity. • Hydroxyl radicals are the main oxidants in formaldehyde and Rhodamine B decomposition. - Abstract: A new mesoporous silica protected plasmonic photocatalyst, Au/BiOCl@mSiO 2 , was prepared by a modified AcHE method and a subsequent UV light induced photodeposition process. The surfactant-free heterojunction allows the electrons spontaneously flow from Au to nearby BiOCl surface, leading to the accumulation of positive charges on Au surface, and negative charges on Bi species under visible light. Au/BiOCl@mSiO 2 exhibits high visible light photocatalytic efficiency in complete oxidation of aqueous formaldehyde and Rhodamin B. We showed that a positive relationship exists between the LSPR effect and rate enhancements, and leads to a hypothesis that the metallic Au LSPR enhances the photocatalytic rates on nearby semiconductors by transferring energetic electrons to BiOCl and increasing the steady-state concentration of active ·OH species by a multi-electron reduction of molecular oxygen. The ·OH species is the main oxidant in photocatalytic transformations, whose intensity is greatly enhanced in the dye-involving systems due to the synergetic effect between LSPR and dye sensitization processes. In addition, the mesoporous SiO 2 shell not only inhibits the over growth of BiOCl nanocrystals within the silica frameworks, but also protects the dissolution of chloride or Au species into aqueous solution, which ultimately makes the Au/BiOCl@mSiO 2 catalysts rather stable during photocatalysis.

Facile synthesis and high activity of novel BiVO{sub 4}/FeVO{sub 4} heterojunction photocatalyst for degradation of metronidazole

Energy Technology Data Exchange (ETDEWEB)

Li, Jinhai [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China); School of Chemical Engineering, Guizhou University of Engineering Science, Bijie 551700 (China); Zhao, Wei; Guo, Yang; Wei, Zhongbo; Han, Mengshu [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China); He, Huan [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China); School of Public Health, University of Illinois at Chicago, Chicago, IL 60631 (United States); Yang, Shaogui [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China); Department of Plant, Soil and Microbial Sciences, Michigan State University, East Lansing, Michigan 48824 (United States); Sun, Cheng, E-mail: envidean@nju.edu.cn [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing 210023 (China)

2015-10-01

Graphical abstract: - Highlights: • BiVO{sub 4}/FeVO{sub 4} was synthesized by a facile one-step hydrothermal method. • BiVO{sub 4}/FeVO{sub 4} displays superior photocatalytic activity. • The photocatalytic mechanism were discussed in detail. - Abstract: The novel BiVO{sub 4}/FeVO{sub 4} heterojunction photocatalyst was successfully synthesized by a facile hydrothermal method firstly. The physical and chemical properties of as-prepared samples were characterized based upon XRD, XPS, BET, SEM, EDS, TEM, UV–vis DRS and fluorescence spectrum techniques. The TEM images showed a clear interface between BiVO{sub 4} and FeVO{sub 4}, indicating that a heterojunction between BiVO{sub 4} and FeVO{sub 4} was formed during the hydrothermal reaction. In addition, the photodegradation activity of metronidazole (MNZ) was used as a measurement for photocatalytic performance of BiVO{sub 4}, FeVO{sub 4} and BiVO{sub 4}/FeVO{sub 4} heterojunction photocatalyst. It indicated that under visible light irradiation the photocatalytic activity of BiVO{sub 4}/FeVO{sub 4} heterojunction photocatalyst was very effective, and moreover, much higher than the single BiVO{sub 4} or single FeVO{sub 4}. The possible photocatalytic mechanism has been discussed on the basis of the theoretical calculation of the electronic structure, and the experimental results.

High-pressure phases in the system W-O. Pt. 2

International Nuclear Information System (INIS)

Barabanenkov, Yu.A.; Zakharov, N.D.; Zibrov, I.P.; Filonenko, V.P.; Werner, P.; Popov, A.I.; Valkovskii, M.D.

1993-01-01

A new type of tungsten oxide has been synthesized from a mixture of W and WO 3 by a solid-phase sintering method under high-pressure conditions. The crystal structure of the new oxide was investigated by HRTEM, selected-area electron diffraction and X-ray powder diffraction. The structure belongs to space group Pbam or P2 1 2 1 2 and has the following unit-cell parameters: a=21.431(9), b=17.766(7), c=3.783(2) A, V=1440 A 3 , Z=32, D x =8.33 g cm -3 . The structural model and W-cation positions were determined by HRTEM and image processing. X-ray powder analysis and the SHELX computer program were used to prove the proposed structural model: N=158, R=0.075, U iso (W)=0.019(3), U iso (O)=0.055(12) A 2 . The investigated crystal structure is, in fact, similar to WO 2.72 and is formed by W-O octahedra and pentagonal bipyramids. (orig.)

Biomimetic fabrication of WO3 for water splitting under visible light with high performance

International Nuclear Information System (INIS)

Yin, Chao; Zhu, Shenmin; Yao, Fan; Gu, Jiajun; Zhang, Wang; Chen, Zhixin; Zhang, Di

2013-01-01

Inspired by the high light-harvesting properties of typical butterfly wings, ceramic WO 3 butterfly wings with hierarchical structures of bio-butterfly wings was fabricated using a template of PapilioParis butterfly wings through a sol–gel method. The effect of calcination temperatures on the structures of the ceramic butterfly wings was investigated and the results showed that the WO 3 butterfly wing replica calcined at 550 °C (WO 3 replica-550) is a single phase and has a high crystallinity and relatively fine hierarchical structure. The average grain size of WO 3 replica-550 and WO 3 powder are around 32.6 and 42.2 nm, respectively. Compared with pure WO 3 powder, WO 3 replica-550 demonstrated a higher light-harvesting capability in the region from 460 to 700 nm and more importantly the higher charge separation rate, as evidenced by electron paramagnetic resonance measurements. Photocatalytic O 2 evolutions from water were investigated on the ceramic butterfly wings and pure WO 3 powder under visible light (λ > 420 nm). The results showed that the amount of O 2 produced from WO 3 replica-550 is 50 % higher than that of the pure WO 3 powder. The improved photocatalytic performance of WO 3 replica-550 is attributed to the quasi-honeycomb structure inherited from the PapilioParis butterfly wings, providing both high light-harvesting efficiency and efficient charge transport through the WO 3

Enhanced visible-light-response photocatalytic degradation of methylene blue on Fe-loaded BiVO{sub 4} photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Chala, Sinaporn [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Wetchakun, Khatcharin [Program of Physics, Faculty of Science, Ubon Ratchathani Rajabhat University, Ubon Ratchathani 34000 (Thailand); Phanichphant, Sukon [Materials Science Research Centre, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Inceesungvorn, Burapat [Department of Chemistry, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Wetchakun, Natda, E-mail: natda_we@yahoo.com [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

2014-06-01

Highlights: • Fe-loaded BiVO{sub 4} particles were prepared by hydrothermal method. • Physicochemical properties played a significant role in photocatalytic process. • All Fe-loaded BiVO{sub 4} samples showed higher photocatalytic activity than pure BiVO{sub 4}. • The Fe{sup 3+} ions may improve the separation of photogenerated electrons and holes. - Abstract: Pure BiVO{sub 4} and nominal 0.5–5.0 mol% Fe-loaded BiVO{sub 4} samples were synthesized by hydrothermal method. All samples were characterized in order to obtain the correlation between structure and photocatalytic properties by X-ray diffraction, Brunauer, Emmett and Teller, UV–vis diffuse reflectance spectrophotometry, photoluminescence spectroscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and inductively coupled plasma-optical emission spectroscopy. The structure of all samples was single-phase monoclinic scheelite. The absorption spectrum of 5.0 mol% Fe-loaded BiVO{sub 4} shifted to the visible region, suggesting the potential application of this material as a superior visible-light driven photocatalyst in comparison with pure BiVO{sub 4}. Photocatalytic activities of all photocatalyst samples were examined by studying the degradation of methylene blue under visible light irradiation. The results clearly showed that Fe-loaded BiVO{sub 4} sample exhibited remarkably higher activity than pure BiVO{sub 4}.

Polar and Magnetic Layered A Site and Rock Salt B Site-Ordered NaLnFeWO6 (Ln = La, Nd) Perovskites

Energy Technology Data Exchange (ETDEWEB)

Tetuerto, Maria [State University of New Jersey, The; Li, Mang-Rong [State University of New Jersey, The; Ignatov, Alexander [State University of New Jersey, The; Croft, Mark [State University of New Jersey, The; Ramanujachary, Kandalam V. [Rowan University; Chi, Songxue [ORNL; Hodges, Jason P [ORNL; Dachraoui, W. [University of Antwerp; Hadermann, Joke [University of Antwerp; Thao Tran, T. [University of Houston, Houston; Shiv Halasyamani, P. [University of Houston, Houston; Grams, C. [Universitat zu Koln, Koln, Germany; Hemberger, J. [Universitat zu Koln, Koln, Germany; Greenblatt, M. [State University of New Jersey, The

2013-01-01

We have expanded the double perovskite family of materials with the unusual combination of layered order in the A sublattice and rock salt order over the B sublattice to compounds NaLaFeWO6 and NaNdFeWO6. The materials have been synthesized and studied by powder X-ray diffraction, neutron diffraction, electron diffraction, magnetic measurements, X-ray absorption spectroscopy, dielectric measurements, and second harmonic generation. At room temperature, the crystal structures of both compounds can be defined in the noncentrosymmetric monoclinic P21 space group resulting from the combination of ordering both in the A and B sublattices, the distortion of the cell due to tilting of the octahedra, and the displacement of certain cations. The magnetic studies show that both compounds are ordered antiferromagnetically below TN 25 K for NaLaFeWO6 and at 21 K for NaNdFeWO6. The magnetic structure of NaNdFeWO6 has been solved with a propagation vector k = (1/2 0 1/2) as an antiferromagnetic arrangement of Fe and Nd moments. Although the samples are potential multiferroics, the dielectric measurements do not show a ferroelectric response.

Investigations on Bi{sub 25}FeO{sub 40} powders synthesized by hydrothermal and combustion-like processes

Energy Technology Data Exchange (ETDEWEB)

Köferstein, Roberto, E-mail: roberto.koeferstein@chemie.uni-halle.de; Buttlar, Toni; Ebbinghaus, Stefan G.

2014-09-15

The syntheses of phase-pure and stoichiometric iron sillenite (Bi{sub 25}FeO{sub 40}) powders by a hydrothermal (at ambient pressure) and a combustion-like process are described. Phase-pure samples were obtained in the hydrothermal reaction at 100 °C (1), whereas the combustion-like process leads to pure Bi{sub 25}FeO{sub 40} after calcination at 750 °C for 2 h (2a). The activation energy of the crystallite growth process of hydrothermally synthesized Bi{sub 25}FeO{sub 40} was calculated as 48(9) kJ mol{sup −1}. The peritectic point was determined as 797(1) °C. The optical band gaps of the samples are between 2.70(7) eV and 2.81(6) eV. Temperature and field-depending magnetization measurements (5−300 K) show a paramagnetic behaviour with a Curie constant of 55.66×10{sup −6} m{sup 3} K mol{sup −1} for sample 1 and C=57.82×10{sup −6} m{sup 3} K mol{sup −1} for sample 2a resulting in magnetic moments of µ{sub mag}=5.95(8) µ{sub B} mol{sup −1} and µ{sub mag}=6.07(4) µ{sub B} mol{sup −1}. The influence of amorphous iron-oxide as a result of non-stoichiometric Bi/Fe ratios in hydrothermal syntheses on the magnetic behaviour was additionally investigated. - Graphical abstract: Bi{sub 25}FeO{sub 40} powders were prepared by a hydrothermal method and a combustion process. The optical band gaps and the peritectic point were determined. The magnetic behaviour was investigated depending on the synthesis and the initial Bi/Fe ratios. The influence of amorphous iron-oxide on the magnetic properties was examined. - Highlights: • Two simple syntheses routes for stoichiometric Bi{sub 25}FeO{sub 40} powders using starch as polymerization agent. • Monitoring the phase evolution and crystallite growth kinetics during the syntheses. • Determination of the optical band gap and melting point. • Investigations of the magnetic behaviour of Bi{sub 25}FeO{sub 40} powders. • Influence of amorphous iron oxide and a non-stoichiometric Bi/Fe ratio on the

Bismuth zinc vanadate, BiZn{sub 2}VO{sub 6}: New crystal structure type and electronic structure

Energy Technology Data Exchange (ETDEWEB)

Eliziario Nunes, Sayonara [Department of Chemistry, Durham University, South Road, Durham DH1 3LE (United Kingdom); Department of Materials Engineering, Federal University of São Carlos, 13565-905 São Carlos, SP (Brazil); Wang, Chun-Hai; So, Karwei; Evans, John S.O. [Department of Chemistry, Durham University, South Road, Durham DH1 3LE (United Kingdom); Evans, Ivana Radosavljević, E-mail: ivana.radosavljevic@durham.ac.uk [Department of Chemistry, Durham University, South Road, Durham DH1 3LE (United Kingdom)

2015-02-15

We report a combined experimental and computational study of the crystal structure and electronic properties of bismuth zinc vanadate, BiZn{sub 2}VO{sub 6}, known for its visible light photocatalytic activity. The crystal structure has been solved from laboratory powder X-ray diffraction data using the repeated minimisations from random starting values method. BiZn{sub 2}VO{sub 6} adopts a new structure type, based on the following building blocks: corner- and edge-sharing ZnO{sub 4} tetrahedra, ZnO{sub 6} octahedra and VO{sub 4} tetrahedra, and Bi{sub 2}O{sub 12} dimers. It is the only known member of the BiM{sub 2}AO{sub 6} (M=Pb, Ca, Cd, Mn, Zn, Mg, Cu; A=V, P, As) family which does not appear to be structurally closely related to others. The electronic structure of BiZn{sub 2}VO{sub 6}, calculated by DFT methods, shows that it is an indirect gap semiconductor with a calculated band gap of 1.6 eV, which compares favourably to the experimentally measured value of 2.4 eV. - Graphical abstract: The crystal structure of BiZn{sub 2}VO{sub 6}, a new structure type in the BiM{sub 2}AO{sub 6} (M=Mg, Ca, Cd, Cu, Pb, Mn, Zn; A=V, P, As) family. - Highlights: • Structure solution from PXRD data by repeated minimisations from random starting values. • New structure type in the BiM{sub 2}AO{sub 6} (M=Pb, Ca, Cd, Mn, Zn, Mg, Cu; A=V, P, As) family. • Electronic structure calculation.

Bi2O3 nanoparticles encapsulated in surface mounted metal-organic framework thin films

Science.gov (United States)

Guo, Wei; Chen, Zhi; Yang, Chengwu; Neumann, Tobias; Kübel, Christian; Wenzel, Wolfgang; Welle, Alexander; Pfleging, Wilhelm; Shekhah, Osama; Wöll, Christof; Redel, Engelbert

2016-03-01

We describe a novel procedure to fabricate a recyclable hybrid-photocatalyst based on Bi2O3@HKUST-1 MOF porous thin films. Bi2O3 nanoparticles (NPs) were synthesized within HKUST-1 (or Cu3(BTC)2) surface-mounted metal-organic frame-works (SURMOFs) and characterized using X-ray diffraction (XRD), a quartz crystal microbalance (QCM) and transmission electron microscopy (TEM). The Bi2O3 semiconductor NPs (diameter 1-3 nm)/SURMOF heterostructures exhibit superior photo-efficiencies compared to NPs synthesized using conventional routes, as demonstrated via the photodegradation of the nuclear fast red (NFR) dye.We describe a novel procedure to fabricate a recyclable hybrid-photocatalyst based on Bi2O3@HKUST-1 MOF porous thin films. Bi2O3 nanoparticles (NPs) were synthesized within HKUST-1 (or Cu3(BTC)2) surface-mounted metal-organic frame-works (SURMOFs) and characterized using X-ray diffraction (XRD), a quartz crystal microbalance (QCM) and transmission electron microscopy (TEM). The Bi2O3 semiconductor NPs (diameter 1-3 nm)/SURMOF heterostructures exhibit superior photo-efficiencies compared to NPs synthesized using conventional routes, as demonstrated via the photodegradation of the nuclear fast red (NFR) dye. Electronic supplementary information (ESI) available. See DOI: 10.1039/c6nr00532b

Structural study, photoluminescence, and photocatalytic activity of semiconducting BaZrO{sub 3}:Bi nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Borja-Urby, R. [Grupo de Espectroscopia de Materiales Avanzados y Nanoestructurados (EMANA), Centro de Investigaciones en Optica A.C., Leon, Gto 37150 (Mexico); Diaz-Torres, L.A., E-mail: ditlacio@cio.mx [Grupo de Espectroscopia de Materiales Avanzados y Nanoestructurados (EMANA), Centro de Investigaciones en Optica A.C., Leon, Gto 37150 (Mexico); Salas, P. [Centro de Fisica Aplicada y Tecnologia Avanzada, Universidad Nacional Autonoma de Mexico, A.P. 1-1010, Queretaro 76000 (Mexico); Moctezuma, E. [Facultad de Ciencias Quimicas, Universidad Autonoma de San Luis Potosi, Av. Manuel Nava 6, San Luis Potosi, S.L.P., Mexico 78290 (Mexico); Vega, M. [Centro de Geociencias-UNAM, A.P. 1-1010, Queretaro 76000 (Mexico); Angeles-Chavez, C. [Instituto Mexicano del Petroleo, Ciudad de Mexico, D.F. 07730 (Mexico)

2011-10-25

Wide band gap nanocrystalline bismuth doped barium zirconate is synthesized by a facile hydrothermal method at 100 deg. C. The obtained cubic perovskites are characterized by powder X-ray diffraction (XRD), UV-VIS diffuse reflectance spectroscopy, photoluminescence (PL) spectroscopy, and photocatalytic activity. The estimated band gap in the 2.4-4.9 eV range, depending on Bi concentration, suggests nanocrystalline BaZrO{sub 3}:Bi as a useful visible-light activated photocatalyst under excitation wavelengths <800 nm. Displacement of main XRD pattern peaks suggest that bismuth ion mostly substitutes into Zr{sup 4+} sites within the BaZrO{sub 3} host lattice. It is found that BaZrO{sub 3}:Bi decomposes methylene blue (MB) under both UV and visible light irradiation. The photocatalyst efficiency depends strongly on Bi content and induced defects.

The highly enhanced visible light photocatalytic degradation of gaseous o-dichlorobenzene through fabricating like-flowers BiPO{sub 4}/BiOBr p-n heterojunction composites

Energy Technology Data Exchange (ETDEWEB)

Zou, Xuejun [Department of Environmental Science and Technology, Dalian Nationalities University, Dalian, 116600 (China); Dong, Yuying, E-mail: dongy@dlnu.edu.cn [Department of Environmental Science and Technology, Dalian Nationalities University, Dalian, 116600 (China); Zhang, Xiaodong, E-mail: fatzhxd@126.com [Environment and Low-Carbon Research Center, School of Environment and Architecture, University of Shanghai for Science and Technology, Shanghai, 200093 (China); Cui, Yubo; Ou, Xiaoxia [Department of Environmental Science and Technology, Dalian Nationalities University, Dalian, 116600 (China); Qi, Xiaohui [College of Life Science, Dalian Nationalities University, Dalian, 116600 (China)

2017-01-01

Highlights: • Like-flowers BiPO{sub 4}/BiOBr was fabricated by mixing in solvent method. • o-Dichlorobenzene removal efficiency was 53.6% using BiPO{sub 4}/BiOBr. • The p–n junction improved o-dichlorobenzene degradation activity. - Abstract: In this paper, in order to enhance photo-induced electron-hole pairs separation of BiOBr, flowers-like BiPO{sub 4}/BiOBr p-n heterojunction composites was fabricated by a mixing in solvent method. The as-prepared samples were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM), UV–vis absorption spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS), and N{sub 2} adsorption-desorption. Meanwhile, their photocatalytic properties were investigated by the degradation of gaseous o-dichlorobenzene under visible light irradiation. Due to its strong adsorption capacity and the formation of p-n heterojunction, compared with BiPO{sub 4} and BiOBr, the BiPO{sub 4}/BiOBr composites showed higher photocatalytic activity in the degradation of gaseous o-DCB under visible light. Among them, 2% BiPO{sub 4}/BiOBr showed the maximum value of the activity, whose degradation rate was about 2.6 times as great as the pure BiOBr. Furthermore, the OH· was confirmed the main active species during the photocatalytic process by the trapping experiments. The outstanding performance indicated that the photocatalysts could be applied to air purification for chlorinated volatile organic compound.

Crystal structure and magnetic properties of the Cr-doped spiral antiferromagnet BiMnFe2O6

International Nuclear Information System (INIS)

Batuk, Dmitry; De Dobbelaere, Christopher; Tsirlin, Alexander A.; Abakumov, Artem M.; Hardy, An; Van Bael, Marlies K.; Greenblatt, Martha; Hadermann, Joke

2013-01-01

Graphical abstract: - Highlights: • The substitution of Cr for Mn in BiMnFe 2 O 6 is possible by the solution–gel method. • The BiCr x Mn 1−x Fe 2 O 6 solid solution is obtained for the x values up to 0.3. • Increasing Cr content lowers the temperature of the antiferromagnetic ordering. - Abstract: We report the Cr 3+ for Mn 3+ substitution in the BiMnFe 2 O 6 structure. The BiCr x Mn 1−x Fe 2 O 6 solid solution is obtained by the solution–gel synthesis technique for the x values up to 0.3. The crystal structure investigation using a combination of X-ray powder diffraction and transmission electron microscopy demonstrates that the compounds retain the parent BiMnFe 2 O 6 structure (for x = 0.3, a = 5.02010(6)Å, b = 7.06594(7)Å, c = 12.6174(1)Å, S.G. Pbcm, R I = 0.036, R P = 0.011) with only a slight decrease in the cell parameters associated with the Cr 3+ for Mn 3+ substitution. Magnetic susceptibility measurements suggest strong similarities in the magnetic behavior of BiCr x Mn 1−x Fe 2 O 6 (x = 0.2; 0.3) and parent BiMnFe 2 O 6 . Only T N slightly decreases upon Cr doping that indicates a very subtle influence of Cr 3+ cations on the magnetic properties at the available substitution rates

Bi{sub 2}O{sub 3} cocatalyst improving photocatalytic hydrogen evolution performance of TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Xu, Difa; Hai, Yang; Zhang, Xiangchao; Zhang, Shiying; He, Rongan, E-mail: hslra@tom.com

2017-04-01

Highlights: • Bi-Bi{sub 2}O{sub 3}-anatase-rutile TiO{sub 2} multijunction photocatalyst was prepared. • Bi{sub 2}O{sub 3} quantum dots with size of 2–3 nm were uniformly distributed. • Improved H{sub 2} evolution was noticed in glycerol-water mixture. • Optimal amount of Bi{sub 2}O{sub 3} was found to be 0.89 mol%. - Abstract: Photocatalytic hydrogen production using water splitting is of potential importance from the viewpoint of renewable energy development. Herein, Bi{sub 2}O{sub 3}-TiO{sub 2} composite photocatalysts presented as Bi-Bi{sub 2}O{sub 3}-anatase-rutile TiO{sub 2} multijunction were first fabricated by a simple impregnation-calcination method using Bi{sub 2}O{sub 3} as H{sub 2}-production cocatalysts. The obtained multijunction samples exhibit an obvious enhancement in photocatalytic H{sub 2} evolution activity in the presence of glycerol. The effect of Bi{sub 2}O{sub 3} amount on H{sub 2}-evolution activity of TiO{sub 2} was investigated and the optimal Bi{sub 2}O{sub 3} content was found to be 0.89 mol%, achieving a H{sub 2}-production rate of 920 μmol h{sup −1}, exceeding that of pure TiO{sub 2} by more than 73 times. The enhanced mechanism of photocatalytic H{sub 2}-evolution activity is proposed. This study will provide new insight into the design and fabrication of TiO{sub 2}-based hydrogen-production photocatalysts using low-cost Bi{sub 2}O{sub 3} as cocatalyst.

Evolution of thermoelectric performance for (Bi,Sb)2Te3 alloys from cutting waste powders to bulks with high figure of merit

International Nuclear Information System (INIS)

Fan, Xi'an; Cai, Xin zhi; Han, Xue wu; Zhang, Cheng cheng

2016-01-01

Bi 2 Te 3 based cutting waste powders from cutting wafers were firstly selected as raw materials to prepare p-type Bi 2 Te 3 based thermoelectric (TE) materials. Through washing, reducing, composition correction, smelting and resistance pressing sintering (RPS) process, p-type (Bi,Sb) 2 Te 3 alloy bulks with different nominal stoichiometries were successfully obtained. The evolution of microstructure and TE performance for (Bi,Sb) 2 Te 3 alloys were investigated in detail. All evidences confirmed that most of contaminants from line cutting process such as cutting fluid and oxides of Bi, Sb or Te could be removed by washing, reducing and smelting process used in this work. The carrier content and corresponding TE properties could be adjusted effectively by appropriate composition correction treatment. At lastly, a bulk with a nominal stoichiometry of Bi 0.44 Sb 1.56 Te 3 was obtained and its' dimensionless figure of merit (ZT) was about 1.16 at 90 °C. The ZT values of Bi 0.36 Sb 1.64 Te 3 and Bi 0.4 Sb 1.6 Te 3 alloy bulks could also reach 0.98 and 1.08, respectively. Different from the conventional recycling technology such as hydrometallurgy extraction methods, the separation and extraction of beneficial elements such as Bi, Sb and Te did not need to be performed and the Bi 2 Te 3 based bulks with high TE properties could be directly obtained from the cutting waste powders. In addition, the recycling technology introduced here was green and more suitable for practical industrial application. It can improve material utilization and lower raw material costs of manufacturers. - Graphical abstract: Three kinds of typical morphologies for the fractographs: typical lamellar structure, agglomerated submicron-sized granules and dispersed cubic particles from the initial cutting waste powders. - Highlights: • Bi 2 Te 3 based wastes were directly selected as raw materials for TE alloys. • Contaminants from cutting fluid and oxides could be effectively removed. �

Photon mass attenuation coefficients of a silicon resin loaded with WO3, PbO, and Bi2O3 Micro and Nano-particles for radiation shielding

Science.gov (United States)

Verdipoor, Khatibeh; Alemi, Abdolali; Mesbahi, Asghar

2018-06-01

Novel shielding materials for photons based on silicon resin and WO3, PbO, and Bi2O3 Micro and Nano-particles were designed and their mass attenuation coefficients were calculated using Monte Carlo (MC) method. Using lattice cards in MCNPX code, micro and nanoparticles with sizes of 100 nm and 1 μm was designed inside a silicon resin matrix. Narrow beam geometry was simulated to calculate the attenuation coefficients of samples against mono-energetic beams of Co60 (1.17 and 1.33 MeV), Cs137 (663.8 KeV), and Ba133 (355.9 KeV). The shielding samples made of nanoparticles had higher mass attenuation coefficients, up to 17% relative to those made of microparticles. The superiority of nano-shields relative to micro-shields was dependent on the filler concentration and the energy of photons. PbO, and Bi2O3 nanoparticles showed higher attenuation compared to WO3 nanoparticles in studied energies. Fabrication of novel shielding materials using PbO, and Bi2O3 nanoparticles is recommended for application in radiation protection against photon beams.

A Novel Heterostructure of BiOI Nanosheets Anchored onto MWCNTs with Excellent Visible-Light Photocatalytic Activity

Directory of Open Access Journals (Sweden)

Shijie Li

2017-01-01

Full Text Available Developing efficient visible-light-driven (VLD photocatalysts for environmental decontamination has drawn significant attention in recent years. Herein, we have reported a novel heterostructure of multiwalled carbon nanotubes (MWCNTs coated with BiOI nanosheets as an efficient VLD photocatalyst, which was prepared via a simple solvothermal method. The morphology and structure were characterized by powder X-ray diffraction (XRD, scanning electron microscopy (SEM, transmission electron microscopy (TEM, UV-Vis diffuse reflectance spectroscopy (DRS, and specific surface area measurements. The results showed that BiOI nanosheets were well deposited on MWCNTs. The MWCNTs/BiOI composites exhibited remarkably enhanced photocatalytic activity for the degradation of rhodamine B (RhB, methyl orange (MO, and para-chlorophenol (4-CP under visible-light, compared with pure BiOI. When the MWCNTs content is 3 wt %, the MWCNTs/BiOI composite (3%M-Bi achieves the highest activity, which is even higher than that of a mechanical mixture (3 wt % MWCNTs + 97 wt % BiOI. The superior photocatalytic activity is predominantly due to the strong coupling interface between MWCNTs and BiOI, which significantly promotes the efficient electron-hole separation. The photo-induced holes (h+ and superoxide radicals (O2− mainly contribute to the photocatalytic degradation of RhB over 3%M-Bi. Therefore, the MWCNTs/BiOI composite is expected to be an efficient VLD photocatalyst for environmental purification.

Evolution of thermoelectric performance for (Bi,Sb)2Te3 alloys from cutting waste powders to bulks with high figure of merit

Science.gov (United States)

Fan, Xi‧an; Cai, Xin zhi; Han, Xue wu; Zhang, Cheng cheng; Rong, Zhen zhou; Yang, Fan; Li, Guang qiang

2016-01-01

Bi2Te3 based cutting waste powders from cutting wafers were firstly selected as raw materials to prepare p-type Bi2Te3 based thermoelectric (TE) materials. Through washing, reducing, composition correction, smelting and resistance pressing sintering (RPS) process, p-type (Bi,Sb)2Te3 alloy bulks with different nominal stoichiometries were successfully obtained. The evolution of microstructure and TE performance for (Bi,Sb)2Te3 alloys were investigated in detail. All evidences confirmed that most of contaminants from line cutting process such as cutting fluid and oxides of Bi, Sb or Te could be removed by washing, reducing and smelting process used in this work. The carrier content and corresponding TE properties could be adjusted effectively by appropriate composition correction treatment. At lastly, a bulk with a nominal stoichiometry of Bi0.44Sb1.56Te3 was obtained and its' dimensionless figure of merit (ZT) was about 1.16 at 90 °C. The ZT values of Bi0.36Sb1.64Te3 and Bi0.4Sb1.6Te3 alloy bulks could also reach 0.98 and 1.08, respectively. Different from the conventional recycling technology such as hydrometallurgy extraction methods, the separation and extraction of beneficial elements such as Bi, Sb and Te did not need to be performed and the Bi2Te3 based bulks with high TE properties could be directly obtained from the cutting waste powders. In addition, the recycling technology introduced here was green and more suitable for practical industrial application. It can improve material utilization and lower raw material costs of manufacturers.

Investigation of the La2O3-Nb2O5-WO3 ternary phase diagram: Isolation and crystal structure determination of the original La3NbWO10 material

KAUST Repository

Vu, T.D.; Vu, T.D.; Barre, M.; Adil, Karim; Jouanneaux, A.; Suard, E.; Goutenoire, F.

2015-01-01

In the course of the exploration of the La2O3-WO3-Nb2O5 ternary phase diagram, a new compound with the formula La3NbWO10 was discovered. Its structure was determined from a combination of powder X-ray and neutron diffraction data. It crystallizes

Phase diagrams of KY(WO4)2-KEr(WO4)2, KGd(WO4)2-KEr(WO4)2 systems and single crystal growth for some tungstates

International Nuclear Information System (INIS)

Yudanova, L.I.; Pavlyuk, A.A.; Potapova, O.G.

1992-01-01

Phase diagrams of the KY(WO 4 ) 2 -KEr(WO 4 ) 2 , KGd(WO 4 ) 2 -KEr(WO 4 ) 2 systems were studied by differential thermal and X-ray diffraction analyses. Continuous variety of solid solutions are in the KY(WO 4 ) 2 -KEr(WO 4 ) 2 system. They occurred just as in the area of alphaso beta-modifications. Limited areas of the solid solutions based on components were in the KGd(WO 4 ) 2 -KEr(WO 4 ) 2 system. Monocrystals of potassium-yttrium and potassium-gadolinium tungstates activated by erbium were grown using modified low-gradient Czochralski method

Biomimetic fabrication of WO{sub 3} for water splitting under visible light with high performance

Energy Technology Data Exchange (ETDEWEB)

Yin, Chao; Zhu, Shenmin, E-mail: smzhu@sjtu.edu.cn; Yao, Fan; Gu, Jiajun; Zhang, Wang [Shanghai Jiao Tong University, State Key Laboratory of Metal Matrix Composites (China); Chen, Zhixin [University of Wollongong, Faculty of Engineering (Australia); Zhang, Di, E-mail: zhangdi@sjtu.edu.cn [Shanghai Jiao Tong University, State Key Laboratory of Metal Matrix Composites (China)

2013-08-15

Inspired by the high light-harvesting properties of typical butterfly wings, ceramic WO{sub 3} butterfly wings with hierarchical structures of bio-butterfly wings was fabricated using a template of PapilioParis butterfly wings through a sol-gel method. The effect of calcination temperatures on the structures of the ceramic butterfly wings was investigated and the results showed that the WO{sub 3} butterfly wing replica calcined at 550 Degree-Sign C (WO{sub 3} replica-550) is a single phase and has a high crystallinity and relatively fine hierarchical structure. The average grain size of WO{sub 3} replica-550 and WO{sub 3} powder are around 32.6 and 42.2 nm, respectively. Compared with pure WO{sub 3} powder, WO{sub 3} replica-550 demonstrated a higher light-harvesting capability in the region from 460 to 700 nm and more importantly the higher charge separation rate, as evidenced by electron paramagnetic resonance measurements. Photocatalytic O{sub 2} evolutions from water were investigated on the ceramic butterfly wings and pure WO{sub 3} powder under visible light ({lambda} > 420 nm). The results showed that the amount of O{sub 2} produced from WO{sub 3} replica-550 is 50 % higher than that of the pure WO{sub 3} powder. The improved photocatalytic performance of WO{sub 3} replica-550 is attributed to the quasi-honeycomb structure inherited from the PapilioParis butterfly wings, providing both high light-harvesting efficiency and efficient charge transport through the WO{sub 3}.

Photoluminescence characteristics of Sm{sup 3+}-doped Ba{sub 2}CaWO{sub 6} as new orange–red emitting phosphors

Energy Technology Data Exchange (ETDEWEB)

Yu, Ruiijn [College of Science, Northwest A and F University, Yangling, Shaanxi 712100 (China); Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Mi Noh, Hyeon; Kee Moon, Byung; Chun Choi, Byung [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Hyun Jeong, Jung, E-mail: jhjeong@pknu.ac.kr [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of); Sueb Lee, Ho [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Jang, Kiwan, E-mail: kwjang@changwon.ac.kr [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Soo Yi, Soung [Department of Electronic Material Engineering, Silla University, Busan 617-736 (Korea, Republic of)

2014-08-01

The orange–red emitting Ba{sub 2}CaWO{sub 6}:xSm{sup 3+} (0.01≤x≤0.25) phosphors were synthesized via solid state reaction process. The crystal structure of the phosphor was characterized by XRD. The photoluminescence excitation and emission spectra, concentration effect were investigated. The results show an efficient energy transfer from WO{sub 6}{sup 6−} group to Sm{sup 3+} occurs. The emission spectra of the Ba{sub 2}CaWO{sub 6}:Sm{sup 3+} phosphors consisted of some sharp emission peaks of Sm{sup 3+} ions centre at 579 nm, 618 nm, 625 nm, and 675 nm. The strongest one is located at 610 nm due to {sup 4}G{sub 5/2}→{sup 6}H{sub 7/2} transition of Sm{sup 3+}, generating bright orange–red light. The optimum dopant concentration of Sm{sup 3+} ions in Ba{sub 2}CaWO{sub 6}:xSm{sup 3+} is around 5 mol% and the critical transfer distance of Sm{sup 3+} is calculated as 18 Å. The fluorescence lifetime of Sm{sup 3+} in Ba{sub 2}CaWO{sub 6}:0.05Sm{sup 3+} is 2.36 ms. The Ba{sub 2}CaWO{sub 6}:Sm{sup 3+} phosphors may be potentially used as orange–red phosphors for white light-emitting diodes. - Highlights: • A new host-sensitized Sm{sup 3+}-doped Ba{sub 2}CaWO{sub 6} phosphor was firstly synthesized. • Its structure, luminescent properties are well studied and characterized. • There exists an efficient energy transfer from WO{sub 6}{sup 6−} group to Sm{sup 3+}. • The thermal quenching properties of Ba{sub 2}CaWO{sub 6}:Sm{sup 3+} was firstly evaluated.

Optical properties and visible-light-driven photocatalytic activity of Bi8V2O17 nanoparticles

International Nuclear Information System (INIS)

Pu, Yinfu; Liu, Ting; Huang, Yanlin; Chen, Cuili; Kim, Sun Il; Seo, Hyo Jin

2015-01-01

Bi 8 V 2 O 17 (4Bi 2 O 3 ·V 2 O 5 ) nanoparticles with the uniform size of about 50 nm were fabricated through the Pechini method. The crystal structure was investigated by X-ray powder diffraction and the structural refinement. The surface of the as-synthesized samples was characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy (EDX), transmission electron microscopy, and X-ray photoelectron spectroscopy. The optical properties, band structure, and the degradation mechanisms were discussed. The experimental results demonstrate that Bi 8 V 2 O 17 nanoparticles have an efficient visible-light absorption with band-gap energy of 1.85 eV and a direct allowed electronic transition. The photocatalytic activity was evaluated by the photodegradation of the methylene blue (MB) under visible-light irradiation (λ > 420 nm) as a function of time. These results indicate that Bi 8 V 2 O 17 could be a potential photocatalyst driven by visible light. The effective photocatalytic activity was discussed on the base of the crystal structure characteristic

Dispersion and guidance characteristics of microstructured 68TeO2 - 22WO3 - 8La2O3 - 2Bi2O3 glass fibres for supercontinuum generation

International Nuclear Information System (INIS)

Yatsenko, Yu P; Nazaryants, V O; Kosolapov, A F; Astapovich, M S; Plotnichenko, V G; Dianov, Evgenii M; Moiseev, A N; Churbanov, M F; Dorofeev, V V; Chilyasov, A V; Snopatin, G E

2010-01-01

We report the preparation of a high-purity optical-quality four-component glass of composition 68TeO 2 - 22WO 3 - 8La 2 O 3 - 2Bi 2 O 3 , containing (2.7±0.5)x10 -5 mol % OH groups. Its refractive index has been determined in the range 0.9 - 5.45 μm using interference refractometry. The data are used to assess the dispersion and guidance characteristics of microstructured optical fibres potentially attractive for supercontinuum generation in the range 1 - 5 μm (optical fibres)

Optical transitions of Er3+/Yb3+ codoped TeO2-WO3-Bi2O3 glass.

Science.gov (United States)

Shen, Xiang; Nie, Qiuhua; Xu, Tiefeng; Gao, Yuan

2005-10-01

Optical absorption and emission properties of the Er3+/Yb3+ codoped TeO2-WO3-Bi2O3 (TWB) glass has been investigated. The transition probabilities, excited state lifetimes, and the branching ratios have been predicted for Er3+ based on the Judd-Ofelt theory. The broad 1.5 microm fluorescence was observed under 970 nm excitation, and its full width at half maximum (FWHM) is 77 nm. The emission cross-section is calculated using the McCumber theory, and the peak emission cross-section is 1.03 x 10(-21) cm2 at 1.531 microm. This value is much larger than those of the silicate and phosphate glasses. Efficient green and weak red upconversion luminescence from Er3+ centers in the glass sample was observed at room temperature, and the upconversion excitation processes have been analyzed.

Crystal structures of the double perovskites Ba2Sr1-x Ca x WO6

International Nuclear Information System (INIS)

Fu, W.T.; Akerboom, S.; IJdo, D.J.W.

2007-01-01

Structures of the double perovskites Ba 2 Sr 1- x Ca x WO 6 have been studied by the profile analysis of X-ray diffraction data. The end members, Ba 2 SrWO 6 and Ba 2 CaWO 6 , have the space group I2/m (tilt system a 0 b - b - ) and Fm3-barm (tilt system a 0 a 0 a 0 ), respectively. By increasing the Ca concentration, the monoclinic structure transforms to the cubic one via the rhombohedral R3-bar phase (tilt system a - a - a - ) instead of the tetragonal I4/m phase (tilt system a 0 a 0 c - ). This observation supports the idea that the rhombohedral structure is favoured by increasing the covalency of the octahedral cations in Ba 2 MM'O 6 -type double perovskites, and disagrees with a recent proposal that the formation of the π-bonding, e.g., d 0 -ion, determines the tetragonal symmetry in preference to the rhombohedral one. - Graphical abstract: Enlarged sections showing the evolution of the basic (222) and (400) reflections in Ba 2 Sr 1- x Ca x WO 6 . Tick marks below are the positions of Bragg's reflections calculated using the space groups I2/m (x=0), R3-bar (x=0.25, 0.5 and 0.75) and Fm3-barm (x=1), respectively

Study of multiferroic properties of Bi2Fe2WO9 ceramic for device application

Directory of Open Access Journals (Sweden)

Jyoshna Rout

2016-09-01

Full Text Available The Bi2Fe2WO9 ceramic was prepared using a standard solid-state reaction technique. Preliminary analysis of X-ray diffraction pattern revealed the formation of single-phase compound with orthorhombic crystal symmetry. The surface morphology of the material captured using scanning electron microscope (SEM exhibits formation of a densely packed microstructure. Comprehensive study of dielectric properties showed two anomalies at 200∘C and 450∘C: first one may be related to magnetic whereas second one may be related to ferroelectric phase transition. The field dependent magnetic study of the material shows the existence of small remnant magnetization (Mr of 0.052emμ/g at room temperature. The existence of magneto-electric (ME coupling coefficient along with above properties confirms multi-ferroic characteristics of the compound. Selected range temperature and frequency dependent electrical parameters (impedance, modulus, conductivity of the compound shows that electric properties are correlated to its microstructure. Detailed studies of frequency dependence of ac conductivity suggest that the material obeys Jonscher’s universal power law.

Efficient visible-light photocatalytic and enhanced photocorrosion inhibition of Ag2WO4 decorated MoS2 nanosheets

Science.gov (United States)

Thangavel, Sakthivel; Thangavel, Srinivas; Raghavan, Nivea; Alagu, Raja; Venugopal, Gunasekaran

2017-11-01

The use of two-dimensional nanomaterials as co-catalysts in the photodegradation of toxic compounds using light irradiation is an attractive ecofriendly process. In this study, we prepared a novel MoS2/Ag2WO4 nanohybrid via a one-step hydrothermal approach and the photocatalytic properties were investigated by the degradation of methyl-orange under stimulated irradiation. The nanohybrid exhibits enhanced efficiency in dye degradation compared to the bare Ag2WO4 nanorods; the same has been evidently confirmed with UV-visible spectra and total organic carbon removal analysis. The pseudo-first order rate constant of the nanohybrid is nearly 1.8 fold higher than that of the bare Ag2WO4 nanorods. With the aid of classical radical quenching and photoluminescence spectral analysis, a reasonable mechanism has been derived for the addition of MoS2 to nanohybrids to enhance the photocatalytic efficiency. MoS2 prevents photocorrosion of Ag2WO4 and also diminishes the number of photogenerated electron-hole recombination. Our findings could provide new insights in understanding the mechanism of the MoS2/Ag2WO4 nanohybrid as an efficient photocatalyst suitable for waste-water treatment and remedial applications.

Facile preparation of Z-scheme WO{sub 3}/g-C{sub 3}N{sub 4} composite photocatalyst with enhanced photocatalytic performance under visible light

Energy Technology Data Exchange (ETDEWEB)

Cui, Lifeng, E-mail: lifeng.cui@gmail.com [School of Chemistry and Environmental Engineering, Dongguan University of Technology, Guangdong 523808 (China); Ding, Xiang; Wang, Yangang; Shi, Huancong; Huang, Lihua; Zuo, Yuanhui [Department of Environmental Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093 (China); Kang, Shifei, E-mail: sfkang@usst.edu.cn [Department of Environmental Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093 (China)

2017-01-01

Highlights: • WO{sub 3}/g-C{sub 3}N{sub 4} composites were synthesized through a facile mixing-and-heating method. • The composite showed improved visible light response. • The composite showed high activity for MB degradation. • Z-scheme charge carrier transfer pathways in the composite are proposed. - Abstract: Visible-light-driven WO{sub 3}/g-C{sub 3}N{sub 4} composites photocatalysts were synthesized via a facile one-step simultaneously heating procedure with urea as the main precursor. These prepared catalyst samples were characterized by X-ray diffraction (XRD), thermogravimetric analysis (TG), transmission electron microscopy (TEM), N{sub 2} adsorption, ultraviolet-visible diffuse reflection spectroscopy (UV–vis), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL) and electrochemical impedance spectroscopy (EIS). The photocatalytic activity of the WO{sub 3}/g-C{sub 3}N{sub 4} composites was evaluated by the photo-degradation of Rhodamine B (RhB) under visible light irradiation. The results indicated that the composites with 25 wt.% WO{sub 3} content exhibited highest photocatalytic activity compared to pure WO{sub 3}, bare g-C{sub 3}N{sub 4} and other WO{sub 3}/g-C{sub 3}N{sub 4} composites. The favorable photocatalytic activity of WO{sub 3}/g-C{sub 3}N{sub 4} composites was mainly attributed to the excellent surface properties, enhanced visible-light absorption and the desirable band positions. A possible Z-scheme photocatalytic mechanism was proposed based on structure and electrochemical characterizations results, which can well explain the enhanced migration rate of photogenerated electrons and holes in WO{sub 3}/g-C{sub 3}N{sub 4} heterojunctions.

Fabrication, characterization and photocatalytic properties of Ag/AgI/BiOI heteronanostructures supported on rectorite via a cation-exchange method

Energy Technology Data Exchange (ETDEWEB)

Chen, Yunfang [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Fang, Jianzhang, E-mail: fangjzh@scnu.edu.cn [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Guangdong Technology Research Center for Ecological Management and Remediation of Urban Water System, Guangzhou 510006 (China); Lu, Shaoyou [Shenzhen Center for Disease Control and Prevention, Shenzhen 518055 (China); Wu, Yan; Chen, Dazhi; Huang, Liyan [Institute of Engineering Technology of Guangdong Province, Key Laboratory of Water Environmental Pollution Control of Guangdong Province, Guangzhou 510440 (China); Xu, Weicheng; Zhu, Ximiao [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Fang, Zhanqiang [School of Chemistry and Environment, South China Normal University, Guangzhou 510006, Guangdong (China); Guangdong Technology Research Center for Ecological Management and Remediation of Urban Water System, Guangzhou 510006 (China)

2015-04-15

Highlights: • Ag/AgI/BiOI-rectorite was prepared by twice cation-exchange process. • Ag/AgI/BiOI-rectorite photocatalyst possessed SPR and adsorption capacity. • Ag/AgI/BiOI-rectorite exhibited highly photocatalytic activity. • Trapped holes and ·O{sub 2}{sup −} were formed active species in the photocatalytic system. - Abstract: In this work, a new plasmonic photocatalyst Ag/AgI/BiOI-rectorite was prepared via a cation exchange process. The photocatalyst had been characterized by X-ray powder diffraction (XRD), Raman spectra, nitrogen sorption (BET), field-emission scanning electron microscope (FE-SEM), X-ray photoelectron spectroscopy (XPS) and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic activity, which was evaluated by degradation of rhodamine B (RhB) and bisphenol A (BPA) under visible light irradiation, was enhanced significantly by loading Ag/AgI/BiOI nanoparticles onto rectorite. The photogenerated holes and superoxide radical (·O{sub 2}{sup −}) were both formed as active species for the photocatalytic reactions under visible light irradiation. The existence of metallic Ag particles, which possess the surface plasmon resonance effect, acted as an indispensable role in the photocatalytic reaction.

Bismuth oxychloride homogeneous phasejunction BiOCl/Bi12O17Cl2 with unselectively efficient photocatalytic activity and mechanism insight

Science.gov (United States)

Hao, Lin; Huang, Hongwei; Guo, Yuxi; Du, Xin; Zhang, Yihe

2017-10-01

Fabrication of homo/hetero-junctions by coupling of wide-band gap semiconductor and narrow-band gap semiconductor is desirable as they can achieve a decent balance between photoabsorption and photo-redox ability. Herein, a n-n type bismuth oxychloride homogeneous phasejunction BiOCl/Bi12O17Cl2 was developed by facilely manipulating the basicity in a one-pot hydrothermal process. Compared with BiOCl which only responds to UV light, the photo-responsive range is remarkably extended to visible region. The BiOCl/Bi12O17Cl2 phasejunctions show much higher photocatalytic activity than the single BiOCl and Bi12O17Cl2 toward degradation of methyl orange (MO) under simulated solar light. In particular, it presented a high photo-oxidation ability in degrading diverse industrial contaminants including 2,4-dichlorophenol (2,4-DCP), phenol, bisphenol A (BPA) and tetracycline hydrochloride. Based on a series of photoelectrochemical and photoluminescence measurements, the fortified photocatalytic performance of BiOCl/Bi12O17Cl2 phasejunctions was manifested to be attributed to the efficient separation and transfer efficiencies of photoinduced electron-hole pairs because of the junctional interface formed between BiOCl and Bi12O17Cl2. The study may not only furnish a high-effective photocatalyst in the application of environment purification, but also pave a path to fabricate agnate phase-junctional photocatalyst.

Enhancement of the chemical stability in confined δ-Bi2O3

DEFF Research Database (Denmark)

Sanna, Simone; Esposito, Vincenzo; Andreasen, Jens Wenzel

2015-01-01

Bismuth-oxide-based materials are the building blocks for modern ferroelectrics1, multiferroics2, gas sensors3, light photocatalysts4 and fuel cells5,6. Although the cubic fluorite δ-phase of bismuth oxide (δ-Bi2O3) exhibits the highest conductivity of known solid-state oxygen ion conductors5, its...... instability prevents use at low temperature7–10. Here we demonstrate the possibility of stabilizing δ-Bi2O3 using highly coherent interfaces of alternating layers of Er2O3-stabilized δ-Bi2O3 and Gd2O3-doped CeO2. Remarkably, an exceptionally high chemical stability in reducing conditions and redox cycles...

Enhanced photosensitization process induced by the p–n junction of Bi2O2CO3/BiOCl heterojunctions on the degradation of rhodamine B

International Nuclear Information System (INIS)

Lu, Haijing; Xu, Lingling; Wei, Bo; Zhang, Mingyi; Gao, Hong; Sun, Wenjun

2014-01-01

Herein, we report the enhanced photosensitization process in the nanosheet Bi 2 O 2 CO 3 /BiOCl heterojunctions photocatalyst. The combined XRD, FT-IR and Raman results have confirmed the co-existence of Bi 2 O 2 CO 3 and BiOCl phases in the composites. Although both Bi 2 O 2 CO 3 and BiOCl are wide bandgap semiconductors, the composites showed an unexpectedly high catalytic activity in decomposing RhB (rhodamine B) aqueous solution under visible light irradiation. The mechanism of enhanced photocatalytic activity was ascribed to the inner electric field formed in the Bi 2 O 2 CO 3 /BiOCl p–n junction.

Silver loaded WO3−x/TiO2 composite multifunctional thin films

International Nuclear Information System (INIS)

Dunnill, Charles W.; Noimark, Sacha; Parkin, Ivan P.

2012-01-01

Multifunctional WO 3−x –TiO 2 composite thin films have been prepared by sol–gel synthesis and shown to be good visible light photocatalysts whilst retaining a desirable underlying blue colouration. The WO 3−x –TiO 2 composite thin films were further enhanced using silver nanoparticles synthesised in-situ on the surface from the photo-degradation of silver nitrate solution. Thin films were characterised using X-ray diffraction, Raman, Scanning electron microscopy and UV–visible spectroscopy and shown to photo degrade stearic acid, using white light λ = 420–800 nm. - Highlights: ► WO 3−X TiO 2 composite thin films were synthesised by sol–gel methods. ► Blue tinted glass is desirable for the value added glass industry. ► Silver nanoparticle island formation enhances the activity of the films. ► Blue tinted “value added” coated glass is now possible.

Photocatalytic properties of KBiO3 and LiBiO3 with tunnel structures

Indian Academy of Sciences (India)

ning Electron Microscopy (SEM), BET surface area analysis and Diffuse Reflectance Spectroscopy (DRS). The. XRD patterns ... The SEM images reveal micron size polyhedral shaped ... based compounds such as BiVO4, Bi2WO6, Bi2MoO6,.

CTAB-assisted ultrasonic synthesis, characterization and photocatalytic properties of WO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Sánchez-Martínez, D., E-mail: dansanm@gmail.com; Gomez-Solis, C.; Torres-Martinez, Leticia M.

2015-01-15

Highlights: • WO{sub 3} 2D nanostructures were synthesized by ultrasound method assisted with CTAB. • WO{sub 3} morphology was mainly of rectangular nanoplates with a thickness of ∼50 nm. • The highest surface area value of WO{sub 3} was obtained to lowest concentration of CTAB. • WO{sub 3} activity was attributed to morphology, surface area and the addition of CTAB. • WO{sub 3} nanoplates were able to causing almost complete mineralization of rhB and IC. - Abstract: WO{sub 3} 2D nanostructures have been prepared by ultrasound synthesis method assisted with CTAB using different molar ratios. The formation of monoclinic crystal structure of WO{sub 3} was confirmed by X-ray powder diffraction (XRD). The characterization of the WO{sub 3} samples was complemented by analysis of scanning electron microscopy (SEM), which revealed morphology mainly of rectangular nanoplates with a thickness of around 50 nm and length of 100–500 nm. Infrared spectroscopy (FT-IR) was used to confirm the elimination of the CTAB in the synthesized samples. The specific surface area was determinate by the BET method and by means of diffuse reflectance spectroscopy (DRS) it was determinate the band-gap energy (E{sub g}) of the WO{sub 3} samples. The photocatalytic activity of the WO{sub 3} oxide was evaluated in the degradation reactions of rhodamine B (rhB) and indigo carmine (IC) under Xenon lamp irradiation. The highest photocatalytic activity was observed in the samples containing low concentration of CTAB with morphology of rectangular nanoplates and with higher surface area value than commercial WO{sub 3}. Photodegradation of rhB and IC were followed by means of UV–vis absorption spectra. The mineralization degree of organic dyes by WO{sub 3} photocatalyst was determined by total organic carbon analysis (TOC) reaching percentages of mineralization of 92% for rhB and 50% for IC after 96 h of lamp irradiation.