WorldWideScience

Sample records for bi-directional dc-dc converter

  1. Bi-Directional DC-DC Converter for PHEV Applications

    Energy Technology Data Exchange (ETDEWEB)

    Abas Goodarzi

    2011-01-31

    Plug-In Hybrid Electric Vehicles (PHEV) require high power density energy storage system (ESS) for hybrid operation and high energy density ESS for Electric Vehicle (EV) mode range. However, ESS technologies to maximize power density and energy density simultaneously are not commercially feasible. The use of bi-directional DC-DC converter allows use of multiple energy storage, and the flexible DC-link voltages can enhance the system efficiency and reduce component sizing. This will improve fuel consumption, increase the EV mode range, reduce the total weight, reduce battery initial and life cycle cost, and provide flexibility in system design.

  2. High efficiency interleaved bi-directional ZVS DC-DC converter

    Science.gov (United States)

    Zafarullah Khan, M.; Mohsin Naveed, M.; Akbar Hussain, D. M.

    2013-06-01

    A high efficiency interleaved bi-directional ZVS DC-DC converter is presented in this paper. This converter can be operated in both buck and boost mode. CoolMOS is used as a power device to achieve low conduction losses and fast turn off. The value of inductance is selected such that the CoolMOS drain-to-source voltage always falls to zero before it turns on and ZVS is achieved. Multiphase interleaved inductors are used to achieve high power and low ripple currents. Converter is operated at 50kHz and MATLAB Simulink simulation is performed. 6kW prototype converter is implemented in buck mode and simulation results are verified.

  3. High Efficiency Interleaved Bi-Directional ZVS DC-DC Converter

    DEFF Research Database (Denmark)

    Zafar Ullah Khan, M.; Mohsin Naveed, M.; Hussain, Dil Muhammad Akbar

    2013-01-01

    MOS drain-to-source voltage always falls to zero before it turns on and ZVS is achieved. Multiphase interleaved inductors are used to achieve high power and low ripple currents. Converter is operated at 50kHz and MATLAB Simulink simulation is performed. 6kW prototype converter is implemented in buck mode...

  4. A novel PWM control for a bi-directional full-bridge DC-DC converter with smooth conversion mode transitions

    Science.gov (United States)

    Lorentz, V. R. H.; Schwarzmann, H.; März, M.; Bauer, A. J.; Ryssel, H.; Frey, L.; Poure, P.; Braun, F.

    2011-08-01

    A novel CMOS integrated pulse-width modulation (PWM) control circuit allowing smooth transitions between conversion modes in full-bridge based bi-directional DC-DC converters operating at high switching frequencies is presented. The novel PWM control circuit is able to drive full-bridge based DC-DC converters performing step-down (i.e. buck) and step-up (i.e. boost) voltage conversion in both directions, thus allowing charging and discharging of the batteries in mobile systems. It provides smooth transitions between buck, buck-boost and boost modes. Additionally, the novel PWM control loop circuit uses a symmetrical triangular carrier, which overcomes the necessity of using an output phasing circuit previously required in PWM controllers based on sawtooth oscillators. The novel PWM control also enables to build bi-directional DC-DC converters operating at high switching frequencies (i.e. up to 10 MHz and above). Finally, the proposed PWM control circuit also allows the use of an average lossless inductor-current sensor for sensing the average load current even at very high switching frequencies. In this article, the proposed PWM control circuit is modelled and the integrated CMOS schematic is given. The corresponding theory is analysed and presented in detail. The circuit simulations realised in the Cadence Spectre software with a commercially available 0.18 µm mixed-signal CMOS technology from UMC are shown. The PWM control circuit was implemented in a monolithic integrated bi-directional CMOS DC-DC converter ASIC prototype. The fabricated prototype was tested experimentally and has shown performances in accordance with the theory.

  5. Analysis and Design of Bi-Directional DC-DC Converter in the Extended Run Time DC UPS System Based on Fuel Cell and Supercapacitor

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2009-01-01

    input voltage combined with load current feedback using PI controller with anti-windup scheme to realize closed-loop control of the whole system, and verify the feasibility of the control scheme proposed by simulation. A 1kW prototype controlled by TMS320F2808 DSP is implemented and tested. Experimental......Abstract-In this paper, an extended run time DC UPS system structure with fuel cell and supercapacitor is investigated. A wide input range bi-directional dc-dc converter is described along with the phase-shift modulation scheme and phase-shift with duty cycle control, in different modes...

  6. A bi-directional DC/DC converter for hybrid wind generator/battery system with state machine control

    Energy Technology Data Exchange (ETDEWEB)

    Hua, C.C.; Liao, Y.C. [National Yunlin Univ. of Science and Technology, Yunlin, Taiwan (China). Dept. of Electrical Engineering

    2008-07-01

    A bi-directional DC to DC converter used in a hybrid wind generator/lead-acid battery power system was presented. A state machine control strategy was used to control both the system power flow and load distribution. It was also used to increase the power capacity of the system. The battery was also charged or discharged through the bi-directional DC to DC converter. Multi-stage current charging control of the batteries was accomplished by adjusting the duty cycle of the power converter. This also improved the charging efficiency by the maximum power point tracking algorithm. It was concluded that the proposed control method can be readily extended to other renewable energy conversion systems. 6 refs., 13 figs.

  7. Advanced DC/DC converters

    CERN Document Server

    Luo, Fang Lin

    2003-01-01

    INTRODUCTIONHistorical ReviewMultiple Quadrant ChoppersPump CircuitsDevelopment of DC/DC Conversion TechniqueCategorize Prototypes and DC/DC Converters Family TreeVOLTAGE-LIFT CONVERTERSIntroductionSeven Self-Lift ConvertersPositive Output Luo-ConvertersNegative Output Luo-ConvertersModified Positive Output Luo-Converters Double Output Luo-ConvertersPOSITIVE OUTPUT SUPER-LIFT LUO-CONVERTERS IntroductionMain SeriesAdditional SeriesEnhanced Series Re-Enhanced Series Multiple-Enhanced Series Summary of Positive Output

  8. Research on control strategy for battery system of photovoltaic power system based on bi-directional DC/DC converter%基于双向变换器的光伏储能控制策略研究

    Institute of Scientific and Technical Information of China (English)

    李鑫; 解璞

    2016-01-01

    独立光伏系统中,储能环节起到平衡功率、稳定系统的关键作用,而合理的控制策略能将储能系统与光伏阵列有机地结合起来,双向 DC/DC变换器正是完成此目标的桥梁。本文在对已有的双向 DC/DC变换器进行优化设计的基础上,提出了一种兼顾电池电性能与系统稳定性的储能系统控制策略。在 Matlab仿真环境下搭建了带有双向 DC/DC变换器的独立光伏系统模型,并对储能系统的工作情况进行仿真,验证了变换器拓扑结构与储能控制策略的合理性。%The independent photovoltaic system needs energy storage in order to balance the power and improve its stability of power generation. A scientiifc control strategy can combine the PV cells with the battery system organically. The bi-directional DC/DC converter can be the bridge to achieve this target. This paper presents a control strategy which takes account of battery electrical performance and system stability based on optimization on the circuit topology of bi-directional DC/DC already underway. Moreover, the charge and discharge circuit based on bi-directional DC/DC converter and an integral independent PV power system are built with Matlab. The simulation results show the correctness of the charge and discharge circuit topology and control strategy.

  9. PWM DC/DC Converter

    OpenAIRE

    Chen, Juan

    2008-01-01

    This report is the result of a Master Thesis work done at Seaward Electronics Inc. in Beijing, China from June to December in 2007. The main goal for this thesis is to verify and improve the performance of Honey-PWM DC-DC converter, which has been fabricated by a standard 0.6um CMOS processes. The project was started with studying of Buck converter structure. After the understanding of the converter structure, the project goes in to the analyses phase for each sub-cells, including the theory,...

  10. 一种软开关的交错并联Buck/Boost双向DC/DC变换器%A Type of Soft-Switching and Interleaving Bi-Directional DC/DC Converter

    Institute of Scientific and Technical Information of China (English)

    朱润卿; 刘军; 徐波

    2016-01-01

    针对传统硬开关双向直流变换器在高频工作时开关损耗较高的缺点,提出一种采用有源箝位软开关的多相交错并联Buck/Boost双向DC/DC变换器.这种变换器的开关管都能在零电压条件下开通,解决了开关管在开通时功率损耗较大的问题.借助SIMetrix软件工具,得出电路仿真结果,结果表明,变换器所有开关在Buck工作模式和Boost工作模式中均能实现软开关工作.%In view of the faults that traditional hard-switching bi-directional DC/DC converter working in high frequency caused much loss, a type of active clamped soft-switching of multiphase interleaving buck/boost bi-directional DC/DC converter is proposed, all switches of converter can be opened at zero voltage, it solves the problem of large loss of power switches.With the help of SIMetrix software tools, circuit simulation results are obtained.The simulation results show that the all switches of converter can achieve soft-switching in the buck mode and in the boost mode.

  11. Research on a Bi-Directional DC-DC Converter Applied in Electric Vehicle%一种应用于电动汽车的双向DC/DC变换器研究

    Institute of Scientific and Technical Information of China (English)

    陈灵敏

    2009-01-01

    In this paper, topology structures of four non-isolated bi-directional DC/DC converter are analyzed and com-pared. A DC-DC converter-interleaving Buck-Boost is designed aiming at the environment protection and storage battery performance of hybrid electric vehicle(HEV). And the working principle of this converter is presented. The theory is testi-fied through a 3 000 W experiment prototype.%分析和比较了四种非隔离型双向DC/DE变换器的拓扑结构.针对目前广泛使用的混合动力电动汽车存在的环保问题和电池性能问题设计了一种双向DC/DC变换器一两相交错双向DC/DC变换器,论述了其工作原理,并通过一台3 000 W的样机验证了理论的正确性.

  12. Hysteretic Current Controlled Zvs Dc/Dc Converter For Automobile

    DEFF Research Database (Denmark)

    Cernat, M.; Scortarul, P.; Tanase, A.

    2007-01-01

    A novel bi-directional dc-dc converter with ZVS and interleaving for dual voltage systems in automobiles is presented. A variable frequency extended band hysteretic current control method is proposed. In comparison with classical fixed frequency current control PWM, the reverse polarity peak curr...

  13. Battery Management System—Balancing Modularization Based on a Single Switched Capacitor and Bi-Directional DC/DC Converter with the Auxiliary Battery

    Directory of Open Access Journals (Sweden)

    Mohamed Daowd

    2014-04-01

    Full Text Available Lithium-based batteries are considered as the most advanced batteries technology, which can be designed for high energy or high power storage systems. However, the battery cells are never fully identical due to the fabrication process, surrounding environment factors and differences between the cells tend to grow if no measures are taken. In order to have a high performance battery system, the battery cells should be continuously balanced for maintain the variation between the cells as small as possible. Without an appropriate balancing system, the individual cell voltages will differ over time and battery system capacity will decrease quickly. These issues will limit the electric range of the electric vehicle (EV and some cells will undergo higher stress, whereby the cycle life of these cells will be shorter. Quite a lot of cell balancing/equalization topologies have been previously proposed. These balancing topologies can be categorized into passive and active balancing. Active topologies are categorized according to the active element used for storing the energy such as capacitor and/or inductive component as well as controlling switches or converters. This paper proposes an intelligent battery management system (BMS including a battery pack charging and discharging control with a battery pack thermal management system. The BMS user input/output interfacing. The battery balancing system is based on battery pack modularization architecture. The proposed modularized balancing system has different equalization systems that operate inside and outside the modules. Innovative single switched capacitor (SSC control strategy is proposed to balance between the battery cells in the module (inside module balancing, IMB. Novel utilization of isolated bidirectional DC/DC converter (IBC is proposed to balance between the modules with the aid of the EV auxiliary battery (AB. Finally an experimental step-up has been implemented for the validation of the

  14. 基于模糊控制的电动车双向DC-DC变换器研究%Research on the Bi-Directional DC-DC Converter of the Electric Vehicle Based on the Fuzzy Control

    Institute of Scientific and Technical Information of China (English)

    崔雪; 郑翔; 穆佩红; 高雅洁

    2014-01-01

    为了延长车辆续航里程,提高蓄电池的使用寿命,使用超级电容作为辅助的能量源,控制超级电容的双向DC-DC变换器对直流母线进行能量的回馈和补充,提高了电动车电源系统效率。根据蓄电池和超级电容的剩余电量及负载瞬态功率需求,提出了一种模糊控制器改善双能量电动车DC-DC变换器性能的方法。模糊控制器根据车辆运行的不同工况,自动地决策出一个合理的输出电流,进而控制双向半桥Buck/Boost式变换器的电流环。实验结果说明了控制系统具有良好的动态性、可行性、有效性。%In order to prolong the driving range and the life cycle of the storage battery, ultracapcitor was used in this study as an auxiliary power source, the bi-directional DC-DC converter of the ultracapacitor was controlled to supplement the energy of the DC bus, and thus the efficiency of the electric vehicle power system was enhanced. Based on the dump energy of the storage battery and ultracapacitor and the need for load transient power, a method was proposed in this paper, in which a fuzzy controller was adopted to improve the performance of the bi-directional DC-DC converter of the electric vehicle. The fuzzy controller could automatically decide on proper output current according to different working conditions of the vehicle, and thereby control the current loop of the bi-directional half-bridge Buck/Boost converter. Simulation results proved that the control system was very dynamic, feasible and effective.

  15. A Family of Non-isolated Bi-directional DC-DC Converters%一族非隔离双向直流变换器

    Institute of Scientific and Technical Information of China (English)

    吴红飞; 陆珏晶; 石巍; 张君君; 邢岩

    2012-01-01

    A family of non-isolated bi-directional DC converter (BDC) based on negative-coupled-inductor (NCI) was proposed. By utilizing the induced potential of the introduced NCI to block the body diode of MOSFET, the reverse-recovery problem associated with the body diode is eliminated. Furthermore, according to the analysis of the equivalent circuit of NCI and filter inductor, by replacing the two inductors with a positive-coupled-inductor (PCI), a family of non-isolated BDC based on PCI was proposed. The control of the proposed BDCs is the same as conventional unidirectional DC converter and has no extra soft start circuit required for the BDCs. The proposed BDCs have advantages of high efficiency, simple control and high reliability. The topology derivation process was presented and the operation principles of the proposed BDCs were analyzed in detail with experimental results given to verify the proposed topologies.%提出一族基于反向耦合电感的非隔离双向直流变换器foi.directionalDCconveaer,BDC),通过引入反向耦合电感,利用电感感应电势阻断不工作MOSFET的体二极管,消除了传统双向变换器中开关管寄生体二极管的反向恢复问题;通过反向耦合电感与滤波电感等效电路的分析,将反向耦合电感与滤波电感用一个同向耦合电感代替,提出一族基于PCI的非隔离双向直流变换器。所提出的变换器控制与传统单向变换器相同,不需要专门的软启动电路,兼顾了较高变换效率、控制简单和高可靠性。给出拓扑推演过程,详细分析拓扑工作原理,并通过实验验证理论分析的正确性。

  16. Local Bifurcations in DC-DC Converters

    OpenAIRE

    2012-01-01

    Three local bifurcations in DC-DC converters are reviewed. They are period-doubling bifurcation, saddle-node bifurcation, and Neimark bifurcation. A general sampled-data model is employed to study the types of loss of stability of the nominal (periodic) solution and their connection with local bifurcations. More accurate prediction of instability and bifurcation than using the averaging approach is obtained. Examples of bifurcations associated with instabilities in DC-DC converters are given.

  17. DC/DC Converter Stability Testing Study

    Science.gov (United States)

    Wang, Bright L.

    2008-01-01

    This report presents study results on hybrid DC/DC converter stability testing methods. An input impedance measurement method and a gain/phase margin measurement method were evaluated to be effective to determine front-end oscillation and feedback loop oscillation. In particular, certain channel power levels of converter input noises have been found to have high degree correlation with the gain/phase margins. It becomes a potential new method to evaluate stability levels of all type of DC/DC converters by utilizing the spectral analysis on converter input noises.

  18. 适合于混合动力汽车新型双向DC/DC变换器研究%Study of One Bi-directional DC/DC Converter for Hybrid Electric Vehicle

    Institute of Scientific and Technical Information of China (English)

    胡建明

    2011-01-01

    首先介绍了一种混合动力汽车的基本电路,然后根据要求设计了一种双向变换器,它具有高功率传输能力和最小开关应力,适合于连接超级电容器来驱动混合动力汽车.与一些典型的隔离式双向DC/DC变换器相比,该变换器具有较低的设备应力,并且可通过相移加PWM控制,采用隔离变压器的漏感作为能量传输单元和控制变量.最后,实验波形证明该变换器能较好地应用于混合动力汽车.%The paper first introduces the basic drive system of a hybrid electric vehicle.Then the selection and design of aforementioned converter are proposed. The converter has high powerflow capability and minimum device stresses that can suitably interface a super capacitor with the drive train of a hybrid electric vehicle. Furthermore ,by comparing of the main characteristics and applications with some typical isolated bi-directional DC/DC converter, the proposed converter has low device rating and can be controlled by duty cycle and phase shift. At last,the most important characteristics of this converter is to uses the transformer leakage inductance as the primary energy transfer element and control parameters, the experimental waveforms are given to demonstrate the goodness of this novel topology which is in particular for hybrid electric vehicle.

  19. CMOS Integrated Capacitive DC-DC Converters

    CERN Document Server

    Van Breussegem, Tom

    2013-01-01

    This book provides a detailed analysis of all aspects of capacitive DC-DC converter design: topology selection, control loop design and noise mitigation. Readers will benefit from the authors’ systematic overview that starts from the ground up, in-depth circuit analysis and a thorough review of recently proposed techniques and design methodologies.  Not only design techniques are discussed, but also implementation in CMOS is shown, by pinpointing the technological opportunities of CMOS and demonstrating the implementation based on four state-of-the-art prototypes.  Provides a detailed analysis of all aspects of capacitive DC-DC converter design;  Analyzes the potential of this type of DC-DC converter and introduces a number of techniques to unleash their full potential; Combines system theory with practical implementation techniques; Includes unique analysis of CMOS technology for this application; Provides in-depth analysis of four fabricated prototypes.

  20. High-Efficiency dc/dc Converter

    Science.gov (United States)

    Sturman, J.

    1982-01-01

    High-efficiency dc/dc converter has been developed that provides commonly used voltages of plus or minus 12 Volts from an unregulated dc source of from 14 to 40 Volts. Unique features of converter are its high efficiency at low power level and ability to provide output either larger or smaller than input voltage.

  1. Radiation effects on DC-DC Converters

    Science.gov (United States)

    Zhang, Dexin; Attia, John O.; Kankam, Mark D. (Technical Monitor)

    2000-01-01

    DC-DC switching converters are circuits that can be used to convert a DC voltage of one value to another by switching action. They are increasing being used in space systems. Most of the popular DC-DC switching converters utilize power MOSFETs. However power MOSFETs, when subjected to radiation, are susceptible to degradation of device characteristics or catastrophic failure. This work focuses on the effects of total ionizing dose on converter performance. Four fundamental switching converters (buck converter, buck-boost converter, cuk converter, and flyback converter) were built using Harris IRF250 power MOSFETs. These converters were designed for converting an input of 60 volts to an output of about 12 volts with a switching frequency of 100 kHz. The four converters were irradiated with a Co-60 gamma source at dose rate of 217 rad/min. The performances of the four converters were examined during the exposure to the radiation. The experimental results show that the output voltage of the converters increases as total dose increases. However, the increases of the output voltage were different for the four different converters, with the buck converter and cuk converter the highest and the flyback converter the lowest. We observed significant increases in output voltage for cuk converter at a total dose of 24 krad (si).

  2. A resonant dc-dc power converter assembly

    DEFF Research Database (Denmark)

    2015-01-01

    The present invention relates to a resonant DC-DC power converter assembly comprising a first resonant DC-DC power converter and a second resonant DC-DC power converter having identical circuit topologies. A first inductor of the first resonant DC-DC power converter and a second inductor...... of the second resonant DC-DC power converter are configured for magnetically coupling the first and second resonant DC-DC power converters to each other to forcing substantially 180 degrees phase shift, or forcing substantially 0 degree phase shift, between corresponding resonant voltage waveforms of the first...... and second resonant DC-DC power converters. The first and second inductors are corresponding components of the first and second resonant DC-DC power converters....

  3. An Efficient DC- DC Converter with Bidirectional Power Flow

    Directory of Open Access Journals (Sweden)

    N.RAJARAJESWARI

    2008-07-01

    Full Text Available This paper introduces a Bi-directional DC-DC converter with adaptive fuzzy logic controller. Bidirectional power flow is obtained by same power components and provides a simple, efficient, and galvanically isolated converter. In the presence of DC mains the converter operates as buck converter and charges the battery. When the DC mains fails, the converter operates as boost converter and the down stream converter is fed by the battery. The power switches are controlled by Pulse Width Modulation technique and the pulses are generated by the application of fuzzy logic with an adoption algorithm. The proposed converter is simulated using MATLAB and laboratory prototype was developed to validate the simulation results.

  4. Multiport Resonant DC-DC Converter

    OpenAIRE

    Tran, Yan-Kim; Dujic, Drazen; Barrade, Philippe

    2015-01-01

    his paper presents a multiport galvanically isolated LLC resonant DC-DC converter suitable for DC applications. A three-port structure is analyzed, with full bidirectional power flow capabilities, simple control and behavior similar to that expected from a DC transformer. Each port is equipped with half-bridge modules accompanied with tuned resonant tank, partly realized with elements of a multi- winding high frequency transformer. With some restrictions that are explained in the paper, each ...

  5. Radiation Effects on DC-DC Converters

    Science.gov (United States)

    Zhang, De-Xin; AbdulMazid, M. D.; Attia, John O.; Kankam, Mark D. (Technical Monitor)

    2001-01-01

    In this work, several DC-DC converters were designed and built. The converters are Buck Buck-Boost, Cuk, Flyback, and full-bridge zero-voltage switched. The total ionizing dose radiation and single event effects on the converters were investigated. The experimental results for the TID effects tests show that the voltages of the Buck Buck-Boost, Cuk, and Flyback converters increase as total dose increased when using power MOSFET IRF250 as a switching transistor. The change in output voltage with total dose is highest for the Buck converter and the lowest for Flyback converter. The trend of increase in output voltages with total dose in the present work agrees with those of the literature. The trends of the experimental results also agree with those obtained from PSPICE simulation. For the full-bridge zero-voltage switch converter, it was observed that the dc-dc converter with IRF250 power MOSFET did not show a significant change of output voltage with total dose. In addition, for the dc-dc converter with FSF254R4 radiation-hardened power MOSFET, the output voltage did not change significantly with total dose. The experimental results were confirmed by PSPICE simulation that showed that FB-ZVS converter with IRF250 power MOSFET's was not affected with the increase in total ionizing dose. Single Event Effects (SEE) radiation tests were performed on FB-ZVS converters. It was observed that the FB-ZVS converter with the IRF250 power MOSFET, when the device was irradiated with Krypton ion with ion-energy of 150 MeV and LET of 41.3 MeV-square cm/mg, the output voltage increased with the increase in fluence. However, for Krypton with ion-energy of 600 MeV and LET of 33.65 MeV-square cm/mg, and two out of four transistors of the converter were permanently damaged. The dc-dc converter with FSF254R4 radiation hardened power MOSFET's did not show significant change at the output voltage with fluence while being irradiated by Krypton with ion energy of 1.20 GeV and LET of 25

  6. Charge pump DC-DC converter comprising solid state batteries

    NARCIS (Netherlands)

    Reefman, D.; Roozeboom, F.; Notten, P.H.L.; Klootwijk, J.H.

    2013-01-01

    An electronic device is provided which comprises a DC-DC converter. The DC-DC converter comprises at least one solid-state rechargeable battery (B1, B2) for storing energy for the DC-DC conversion and an output capacitor (C2).

  7. Radiation-Tolerant DC-DC Converters

    Science.gov (United States)

    Skutt, Glenn; Sable, Dan; Leslie, Leonard; Graham, Shawn

    2012-01-01

    A document discusses power converters suitable for space use that meet the DSCC MIL-PRF-38534 Appendix G radiation hardness level P classification. A method for qualifying commercially produced electronic parts for DC-DC converters per the Defense Supply Center Columbus (DSCC) radiation hardened assurance requirements was developed. Development and compliance testing of standard hybrid converters suitable for space use were completed for missions with total dose radiation requirements of up to 30 kRad. This innovation provides the same overall performance as standard hybrid converters, but includes assurance of radiation- tolerant design through components and design compliance testing. This availability of design-certified radiation-tolerant converters can significantly reduce total cost and delivery time for power converters for space applications that fit the appropriate DSCC classification (30 kRad).

  8. Analysis and design of PPFHB bidirectional DC-DC converter with coupled inductors

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael Andreas E.

    2009-01-01

    In this paper, a novel push-pull-forward half-bridge (PPFHB) bi-directional DC-DC converter with coupled inductors is proposed. All switches can operate under zero-voltage-switching (ZVS). The operation principle with phase-shift modulation scheme, characteristics of coupled inductors, the steady...

  9. A Multi-Level Grid Interactive Bi-directional AC/DC-DC/AC Converter and a Hybrid Battery/Ultra-capacitor Energy Storage System with Integrated Magnetics for Plug-in Hybrid Electric Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Onar, Omer C [ORNL

    2011-01-01

    This study presents a bi-directional multi-level power electronic interface for the grid interactions of plug-in hybrid electric vehicles (PHEVs) as well as a novel bi-directional power electronic converter for the combined operation of battery/ultracapacitor hybrid energy storage systems (ESS). The grid interface converter enables beneficial vehicle-to-grid (V2G) interactions in a high power quality and grid friendly manner; i.e, the grid interface converter ensures that all power delivered to/from grid has unity power factor and almost zero current harmonics. The power electronic converter that provides the combined operation of battery/ultra-capacitor system reduces the size and cost of the conventional ESS hybridization topologies while reducing the stress on the battery, prolonging the battery lifetime, and increasing the overall vehicle performance and efficiency. The combination of hybrid ESS is provided through an integrated magnetic structure that reduces the size and cost of the inductors of the ESS converters. Simulation and experimental results are included as prove of the concept presenting the different operation modes of the proposed converters.

  10. A Reduced-Part, Triple-Voltage DC-DC Converter for Electric Vehicle Power Management

    Energy Technology Data Exchange (ETDEWEB)

    Su, Gui-Jia [ORNL; Tang, Lixin [ORNL

    2007-01-01

    Electrical power systems in future hybrid and fuel cell vehicles may consist of three voltage nets; 14 V, 42 V and high voltage (>200 V) buses. A soft-switched, bi-directional dc-dc converter using only four switches was proposed for interconnecting the three nets. This paper presents a reduced- part dc-dc converter, which decreases the converter cost while retaining all the favorable features of the original topology. Simulation and experimental data are included to verify a simple power flow control scheme.

  11. Intelligent dc-dc Converter Technology Developed and Tested

    Science.gov (United States)

    Button, Robert M.

    2001-01-01

    The NASA Glenn Research Center and the Cleveland State University have developed a digitally controlled dc-dc converter to research the benefits of flexible, digital control on power electronics and systems. Initial research and testing has shown that conventional dc-dc converters can benefit from improved performance by using digital-signal processors and nonlinear control algorithms.

  12. Early Oscillation Detection for DC/DC Converter Fault Diagnosis

    Science.gov (United States)

    Wang, Bright L.

    2011-01-01

    The electrical power system of a spacecraft plays a very critical role for space mission success. Such a modern power system may contain numerous hybrid DC/DC converters both inside the power system electronics (PSE) units and onboard most of the flight electronics modules. One of the faulty conditions for DC/DC converter that poses serious threats to mission safety is the random occurrence of oscillation related to inherent instability characteristics of the DC/DC converters and design deficiency of the power systems. To ensure the highest reliability of the power system, oscillations in any form shall be promptly detected during part level testing, system integration tests, flight health monitoring, and on-board fault diagnosis. The popular gain/phase margin analysis method is capable of predicting stability levels of DC/DC converters, but it is limited only to verification of designs and to part-level testing on some of the models. This method has to inject noise signals into the control loop circuitry as required, thus, interrupts the DC/DC converter's normal operation and increases risks of degrading and damaging the flight unit. A novel technique to detect oscillations at early stage for flight hybrid DC/DC converters was developed.

  13. On and off controlled resonant dc-dc power converter

    DEFF Research Database (Denmark)

    2015-01-01

    The present invention relates to a resonant DC-DC power converter comprising an input side circuit comprising a positive and a negative input terminal for receipt of an input voltage or current and an output side circuit comprising positive and negative output terminals for supply of a converter...... output voltage and connection to a converter load. The resonant DC-DC power converter further comprises a rectification circuit connected between an output of a resonant network and the output side circuit. The resonant network is configured for alternatingly being charged from the input voltage...... or current and discharged through the rectification circuit by a first controllable switch arrangement in accordance with a first switch control signal. A second controllable switch arrangement of the resonant DC-DC power converter is configured to select a first impedance characteristic of the resonant...

  14. DC-DC power converter research for Orbiter/Station power exchange

    Science.gov (United States)

    Ehsani, M.

    1993-01-01

    This project was to produce innovative DC-DC power converter concepts which are appropriate for the power exchange between the Orbiter and the Space Station Freedom (SSF). The new converters must interface three regulated power buses on SSF, which are at different voltages, with three fuel cell power buses on the Orbiter which can be at different voltages and should be tracked independently. Power exchange is to be bi-directional between the SSF and the Orbiter. The new converters must satisfy the above operational requirements with better weight, volume, efficiency, and reliability than is available from the present conventional technology. Two families of zero current DC-DC converters were developed and successfully adapted to this application. Most of the converters developed are new and are presented.

  15. Isolated Bidirectional DC-DC Converter for Hybrid Electric Vehicle Application

    Science.gov (United States)

    2006-06-13

    34Approved for public release: distribution is unlimited" Isolated Bidirectional DC-DC Converter for Hybrid Electric Vehicle Applications Sonya...requirements for DC-DC converters for electric and hybrid vehicles . This paper introduces a bidirectional, isolated DC-DC converter for medium power...the design and build of a medium power DC-DC converter . Key words: Power Converter , DC-DC, Hybrid Electric Vehicle , Battery, Galvanically Isolation

  16. Very High Frequency Half Bridge DC/DC Converter

    DEFF Research Database (Denmark)

    Madsen, Mickey Pierre; Knott, Arnold; Andersen, Michael A. E.

    2014-01-01

    This paper presents the first, off chip, class DE (resonant half bridge) converter working in the Very High Frequency (VHF) range. The benefits of using half bridge circuits both in the inverter and rectifier part of a VHF resonant dc/dc converter are analyzed and design equations for all...

  17. A Novel FPSM Controller for DC-DC Switching Converters

    Institute of Scientific and Technical Information of China (English)

    Yong Feng; Shun-Ping Wang; Ping Luo; Quan-Ming Niu; Zhao-Ji Li

    2007-01-01

    This paper presents a novel fuzzy pulse skip modulation (FPSM) controller for switching direct current to direct current (DC-DC) converters based on fuzzy ratiocination modeling approach. Owing to the optimal consideration during the design and the nonlinear characteristics of the controller, improved dynamic responses of the FPSM controller can be achieved over conventional controllers. Compared with conventional proportion integral derivative (PID) control, FPSM control has 60% lower overshoot and 10% lower setting time under the same input voltage and output load change. The presented approach is general and can be applied to other types of DC-DC converters.

  18. Planar integrated magnetics design in wide input range DC-DC converter for fuel cell application

    DEFF Research Database (Denmark)

    Ouyang, Ziwei; Zhang, Zhe; Thomsen, Ole Cornelius;

    2010-01-01

    , hereby increasing the power density of converters. A new planar integrated magnetics (PIM) technique for a phase-shift plus duty cycle controlled hybrid bi-directional DC/DC converter is presented and investigated in this paper. The main magnetic components including one boost inductor and two......In the most power electronics converters, the overall volume is mainly determined by the number of parts and the size of passive components. Integrated magnetics and planar magnetics techniques therefore have been an excellent option in order to reduce the count and the size of magnetic components...

  19. High Voltage Bi-directional Flyback Converter for Capacitive Actuator

    DEFF Research Database (Denmark)

    Thummala, Prasanth; Zhang, Zhe; Andersen, Michael A. E.

    2013-01-01

    This paper presents a high voltage DC-DC converter topology for bi-directional energy transfer between a low voltage DC source and a high voltage capacitive load. The topology is a bi-directional flyback converter with variable switching frequency control during the charge mode, and constant...... switching frequency control during the discharge mode. The converter is capable of charging the capacitive load from 24 V DC source to 2.5 kV, and discharges it to 0 V. The flyback converter has been analyzed in detail during both charge and discharge modes, by considering all the parasitic elements...... in the converter, including the most dominating parameters of the high voltage transformer viz., self-capacitance and leakage inductance. The specific capacitive load for this converter is a dielectric electro active polymer (DEAP) actuator, which can be used as an effective replacement for conventional actuators...

  20. Early Oscillation Detection Technique for Hybrid DC/DC Converters

    Science.gov (United States)

    Wang, Bright L.

    2011-01-01

    Oscillation or instability is a situation that must be avoided for reliable hybrid DC/DC converters. A real-time electronics measurement technique was developed to detect catastrophic oscillations at early stages for hybrid DC/DC converters. It is capable of identifying low-level oscillation and determining the degree of the oscillation at a unique frequency for every individual model of the converters without disturbing their normal operations. This technique is specially developed for space-used hybrid DC/DC converters, but it is also suitable for most of commercial and military switching-mode power supplies. This is a weak-electronic-signal detection technique to detect hybrid DC/DC converter oscillation presented as a specific noise signal at power input pins. It is based on principles of feedback control loop oscillation and RF signal modulations, and is realized by using signal power spectral analysis. On the power spectrum, a channel power amplitude at characteristic frequency (CPcf) and a channel power amplitude at switching frequency (CPsw) are chosen as oscillation level indicators. If the converter is stable, the CPcf is a very small pulse and the CPsw is a larger, clear, single pulse. At early stage of oscillation, the CPcf increases to a certain level and the CPsw shows a small pair of sideband pulses around it. If the converter oscillates, the CPcf reaches to a higher level and the CPsw shows more high-level sideband pulses. A comprehensive stability index (CSI) is adopted as a quantitative measure to accurately assign a degree of stability to a specific DC/DC converter. The CSI is a ratio of normal and abnormal power spectral density, and can be calculated using specified and measured CPcf and CPsw data. The novel and unique feature of this technique is the use of power channel amplitudes at characteristic frequency and switching frequency to evaluate stability and identify oscillations at an early stage without interfering with a DC/DC converter s

  1. A Current-Fed Isolated Bidirectional DC-DC Converter

    DEFF Research Database (Denmark)

    Sun, Xiaofeng; Wu, Xiaoying; Shen, Yanfeng;

    2017-01-01

    This paper proposes a current-fed isolated bidirectional DC-DC converter (CF-IBDC) which has the advantages of wide input voltage range, low input current ripple, low conduction losses, and soft switching over the full operating range. Compared with conventional CF-IBDCs, the voltage spikes of th...

  2. An organic integrated capacitive DC-DC up-converter

    NARCIS (Netherlands)

    Marien, H.; Steyaert, M.; Steudel, S.; Vicca, P.; Smout, S.; Gelinck, G.H.; Heremans, P.L.

    2010-01-01

    In this paper a fully integrated organic DC-DC upconverter is presented in a pentacene p-type only technology. This 3-stage Dickson converter reaches a voltage conversion factor of 3 for a purely capacitive load and 2.5 for a 10 μA load current. The maximal output voltage goes up to 75 V and the Dic

  3. A Novel High Gain DC-DC Step up Converter

    Directory of Open Access Journals (Sweden)

    M. Al Mamun

    2016-07-01

    Full Text Available High gain dc-dc converters are widely used to maximize the energy harvest for renewable energy systems, for example, photovoltaic systems and fuel cell. Conventional boost converters usually operates at extreme duty cycle to obtain high voltage gain. Operation at extreme duty cycle leads to reverse recovery problem at the switches, high conduction loss, electromagnetic interference etc. This paper proposes a very high gain dc-dc step up converter operating at very low duty cycle (i.e. duty cycle <0.5. The additional advantage of the proposed converter is that a single control signal is used for the switches which reduces the operation complexity. The steady-state theoretical analysis described in this paper is finally verified by simulation results

  4. Step-Up DC-DC Power Converter

    DEFF Research Database (Denmark)

    2015-01-01

    The present invention relates to a step-up DC-DC power converter which comprises a primary side circuit and a secondary side circuit coupled through a galvanic isolation barrier. The primary side circuit comprises a positive and a negative input terminal for receipt of an input voltage and an input...... being charged from the input voltage and discharged to the output capacitor through the galvanic isolation barrier in accordance with a switch control signal to produce the converter output voltage. The step-up DC-DC power converter comprises an electrical short-circuit connection across the galvanic...... capacitor coupled between the positive and negative input terminals and the secondary side circuit comprises an output capacitor chargeable to a converter output voltage between a first positive electrode and a second negative electrode. A switched energy storage network is configured for alternatingly...

  5. GaN Microwave DC-DC Converters

    Science.gov (United States)

    Ramos Franco, Ignacio

    Increasing the operating frequency of switching converters can have a direct impact in the miniaturization and integration of power converters. The size of energy-storage passive components and the difficulty to integrate them with the rest of the circuitry is a major challenge in the development of a fully integrated power supply on a chip. The work presented in this thesis attempts to address some of the difficulties encountered in the design of high-frequency converters by applying concepts and techniques usually used in the design of high-efficiency power amplifiers and high-efficiency rectifiers at microwave frequencies. The main focus is in the analysis, design, and characterization of dc-dc converters operating at microwave frequencies in the low gigahertz range. The concept of PA-rectifier duality, where a high-efficiency power amplifier operates as a high-efficiency rectifier is investigated through non-linear simulations and experimentally validated. Additionally, the concept of a self-synchronous rectifier, where a transistor rectifier operates synchronously without the need of a RF source or driver is demonstrated. A theoretical analysis of a class-E self-synchronous rectifier is presented and validated through non-linear simulations and experiments. Two GaN class-E2 dc-dc converters operating at a switching frequency of 1 and 1.2 GHz are demonstrated. The converters achieve 80 % and 75 % dc-dc efficiency respectively and are among the highest-frequency and highest-efficiency reported in the literature. The application of the concepts established in the analysis of a self-synchronous rectifier to a power amplifier culminated in the development of an oscillating, self-synchronous class-E 2 dc-dc converter. Finally, a proof-of-concept fully integrated GaN MMIC class-E 2 dc-dc converter switching at 4.6 GHz is demonstrated for the first time to the best of our knowledge. The 3.8 mm x 2.6 mm chip contains distributed inductors and does not require any

  6. Efficient, lightweight dc/dc switching converter

    Science.gov (United States)

    Cuk, S.; Middlebrook, R. D.

    1981-01-01

    Converters have input properties of boost power stage and output properties of buck power stage, yet they perform general conversion function with high efficiency. Other features include non-pulsating input/output currents, use of capacitive energy transfer, low output voltage ripple, reduced EMI, and small size.

  7. Digital Control Technologies for Modular DC-DC Converters

    Science.gov (United States)

    Button, Robert M.; Kascak, Peter E.; Lebron-Velilla, Ramon

    2002-01-01

    Recent trends in aerospace Power Management and Distribution (PMAD) systems focus on using commercial off-the-shelf (COTS) components as standard building blocks. This move to more modular designs has been driven by a desire to reduce costs and development times, but is also due to the impressive power density and efficiency numbers achieved by today's commercial DC-DC converters. However, the PMAD designer quickly learns of the hidden "costs" of using COTS converters. The most significant cost is the required addition of external input filters to meet strict electromagnetic interference (MIAMI) requirements for space systems. In fact, the high power density numbers achieved by the commercial manufacturers are greatly due to the lack of necessary input filters included in the COTS module. The NASA Glenn Research Center is currently pursuing a digital control technology that addresses this problem with modular DC-DC converters. This paper presents the digital control technologies that have been developed to greatly reduce the input filter requirements for paralleled, modular DC-DC converters. Initial test result show that the input filter's inductor size was reduced by 75 percent, and the capacitor size was reduced by 94 percent while maintaining the same power quality specifications.

  8. Radiated electromagnetic emissions of DC-DC converters

    CERN Document Server

    Sammet, Jan Domenik

    2010-01-01

    A new powering scheme is considered to be mandatory for the CMS tracker at SLHC. The baseline solution of CMS foresees the use of DC-DC converters, allowing to provide larger currents while reducing losses. An important component of most converters are inductors, which, however, tend to radiate the switching noise generated by the converter. The radiated emissions of several converters have been measured and simulated. In addition noise susceptibility measurements with radiated noise and present CMS hardware have been performed. A summary of the results will be presented.

  9. Radiated electromagnetic emissions of DC-DC converters

    Energy Technology Data Exchange (ETDEWEB)

    Feld, L; Jussen, R; Karpinski, W; Klein, K; Sammet, J; Wlochal, M, E-mail: sammet@cern.ch [Physikalisches Institut IB, RWTH Aachen University, Aachen (Germany)

    2010-12-15

    For the CMS tracker at SLHC a new powering scheme is considered to be mandatory to allow the detector to provide at least the same performance as today at the LHC. The baseline solution of CMS foresees the use of DC-DC converters to provide larger currents with smaller losses. An important component of most converters are inductors which, however, tend to radiate the switching noise generated by the converter. The emissions of different inductors have been measured and simulated, the coil design has been optimized and noise susceptibility measurements, with present CMS hardware, have been performed. This article summarizes the results.

  10. Modular Power System Configured with Standard Product Hybrid DC-DC Converters Project

    Data.gov (United States)

    National Aeronautics and Space Administration — VPT proposes an innovative concept whereby complex, multiple-output, DC-DC converter systems can be configured through use of only 2 standard product hybrid DC-DC...

  11. Low dose failures of hardened DC-DC power converters

    Science.gov (United States)

    Lehman, J.; Yui, C.; Rax, B. G.; Miyahira, T. F.; Weideman, M.; Schrick, P.; Swift, G. M.; Johnston, A. H.

    2002-01-01

    Box-level total dose testing of the FOG (Fiber Optic Gyro) by IXSEA at ESA's GammabeamFacility were abruptly terminated at 8krad (Si) due to catastrophic failure (complete shutdown). This was unexpected because all components within the gyro were supposedly radiation tolerant. Further testing showed that the components responsible for the failure were two DC-DC converters, manufactured by Interpoint, that stopped regulating shortly before shutdown. This paper summarizes diagnostic test results for the converters to determine the underlying cause of the unexpected failure at low levels of radiation.

  12. Modified Multiport Dc-Dc Converter Topology For Smart Grid

    Directory of Open Access Journals (Sweden)

    Dhamodharan Shanmugam

    2013-10-01

    Full Text Available The development of a Solid State Transformer (SST that incorporates a DC-DC multiport converter to integrate both photovoltaic (PV power generation and battery energy storage is presented in this dissertation. The DC-DC stage is based on a quad active-bridge (QAB converter which not only provides isolation for the load, but also for the PV and storage. The AC-DC stage is implemented with a pulse-widthmodulated (PWM single phase rectifier. A unified gyrator-based average model is developed for a general multi-active-bridge (MAB converter controlled through phase-shift modulation (PSM. Expressions to determine the power rating of the MAB ports are also derived. The developed gyrator-based average model is applied to the QAB converter for faster simulations of the proposed SST during the control design process as well for deriving the state-space representation of the plant. Both linear quadratic regulator (LQR and singleinput-single-output (SISO types of controllers are designed for the DC-DC stage. A novel technique that complements the SISO controller by taking into account the cross coupling characteristics of the QAB converter is also presented herein. Cascaded SISO controllers are designed for the AC-DC stage. The QAB demanded power is calculated at the QAB controls and then fed into the rectifier controls in order to minimize the effect of the interaction between the two SST stages. The dynamic performance of the designed control loops based on the proposed control strategies are verified through extensive simulation of the SST average and switching models.

  13. Planar Integrated Magnetics (PIM) Module in Hybrid Bidirectional DC-DC Converter for Fuel Cell Application

    DEFF Research Database (Denmark)

    Ouyang, Ziwei; Zhang, Zhe; Thomsen, Ole Cornelius;

    2011-01-01

    , hereby increasing the power density of converters. In this paper, a new planar integrated magnetics (PIM) module for a phase-shift plus duty cycle controlled hybrid bi-directional dc-dc converter is proposed, which assembles one boost inductor and two transformers into an E-I-E core geometry, reducing......In most power electronics converters, the overall volume is mainly determined by the number of parts and the size of passive components. Integrated magnetics and planar magnetics techniques therefore have been an excellent option in order to reduce the counts and the size of magnetic components...... the number of parts, the total volume of converter, as well as the total core loss of the magnetic components. AC losses in the windings and leakage inductance of the transformers are kept low by interleaving the primary and secondary turns of the transformers. To verify the validity of the design approach...

  14. A DC-DC Converter with Wide Input Voltage Range for Fuel Cell and Supercapacitor Application

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael Andreas E.

    2009-01-01

    This paper proposes a novel phase-shift plus duty cycle controlled hybrid bi-directional DC-DC converter based on fuel cells and supercapacitors. The described converter employs two high frequency transformers to couple the half-bridge and full-bridge circuits together in the primary side...... and voltage doubler circuit in secondary side. Boost type converter can limit the output ripple current of the fuel cells; hybrid full-bridge structure can change operating modes according to the different input voltage; phase-shift with duty cycle control scheme is utilized to control the bidirectional power...... flow flexibly. All the switches can turn on under zero-voltage-switching condition (ZVS). The operating principles of the converter are described in details, and the experimental results based on the prototype controlled by DSP are presented to verify the validity of the analysis and design....

  15. Optimization of DC-DC Converters via Geometric Programming

    Directory of Open Access Journals (Sweden)

    U. Ribes-Mallada

    2011-01-01

    Full Text Available The paper presents a new methodology for optimizing the design of DC-DC converters. The magnitudes that we take into account are efficiency, ripples, bandwidth, and RHP zero placement. We apply a geometric programming approach, because the variables are positives and the constraints can be expressed in a posynomial form. This approach has all the advantages of convex optimization. We apply the proposed methodology to a boost converter. The paper also describes the optimum designs of a buck converter and a synchronous buck converter, and the method can be easily extended to other converters. The last example allows us to compare the efficiency and bandwidth between these optimal-designed topologies.

  16. Study of nonlinear phenomena in switching DC/DC converters

    Science.gov (United States)

    Iu, Herbert Ho-Ching

    This thesis studies some nonlinear phenomena such as bifurcation and chaos in DC/DC switching converters. Five phases of investigations are described. The first phase reviews the existing tools for analyzing nonlinear systems that are helpful to the investigation of nonlinear phenomena in power electronic circuits. Some of these existing tools are employed to study the nonlinear behaviour of power electronic circuits in the subsequent phases. The second phase focuses on the analysis of bifurcation behaviour of parallel-connected DC/DC converters under a master-slave current sharing scheme. An iterative discrete-time map and its Jacobian are established to predict the onset of period-doubling or Neimark-Sacker bifurcation. Both parallel-connected buck converters and boost converters are studied. The third phase studies an autonomous free-running Cuk converter under a hysteretic current-mode control. Hopf bifurcation is observed, for the first time, in this kind of autonomous power electronic circuits. The method of state-space averaging is employed to predict the occurrence of such bifurcation. Extensive simulations and experiments confirm the predicted results. A typical bifurcation sequence from stable fixed points to chaos, via limit cycles and quasiperiodic orbits, is demonstrated. The fourth phase investigates the possibility of synchronization of two chaotic autonomous free-running Cuk converters. With a particular capacitor voltage as driving signal, synchronization is found possible. Averaged state equations and conditional Lyapunov exponents are used to predict the possibility of synchronization while computer simulations and PSPICE simulations provide the verification. The last phase gives suggestions for future research.

  17. RESONANT STEP-DOWN DC-DC POWER CONVERTERS

    DEFF Research Database (Denmark)

    2015-01-01

    charged from the input voltage and discharged to the output capacitor through the galvanic isolation barrier by a semiconductor switch arrangement in accordance with a switch control signal to produce the converter output voltage. The resonant step-down DC-DC power converter comprises an electrical short...... of the primary side circuit thereby establishing in both the first and second cases a series coupling of the output capacitor and the input capacitor. A load connection is established, in the first case, between the first positive electrode of the output capacitor and the positive input terminal or......-circuit connection across the galvanic isolation barrier connecting, in a first case, the second negative electrode of the output capacitor to the positive input terminal of the primary side circuit or, in a second case, connecting the second positive electrode of the output capacitor to the negative input terminal...

  18. DC/DC converter with improved rectification for higher efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Maisel, Peter; Saliternig, Martin [Continental AG, Nuernberg (Germany)

    2010-07-01

    High-power dc-dc converters are an important element of the electrical system of electric vehicles and hybrid electric vehicles. These complex modular components provide the link between the high-voltage level used for the powertrain and the low-voltage bus for the lighting system, engine management and auxiliary needs in the vehicle. The essential requirements for all converters are high efficiency, compact size, lightweight and reliability. A very popular method to increase the efficiency is the synchronous rectification. Parasitic inductances in the commutation circuit and reverse recovery effects can produce a ringing with voltage overshoots at the diodes and the transistors. These spikes can cause higher average power dissipation in the seminconductors and higher EMI (electromagnetic interference).

  19. Model of Bi-directional Flyback Converter for Hybrid AC/DC Distribution System

    Directory of Open Access Journals (Sweden)

    Riku Pasonen

    2013-12-01

    Full Text Available In this article, a simulation model and concept of two switch bi-directional isolated DC/DC converter is presented. Converter is based on flyback converter type. Also control method for voltage regulation with bi-directional power transfer is presented. Target application of the proposed converter was selected to be a hybrid AC/DC distribution system concept of which was briefly described. The requirement of galvanic isolation in the hybrid AC/DC concept comes from use of shared neutral wire; DC current runs with unbalanced part of AC current in neutral wire. Without galvanic isolation grounded neutral would cause short circuit if DC/DC converter is connected to three phase rectifier or inverter. Simulation was carried out with PSCAD electromagnetic transient simulator.

  20. An Integrated Programmable Wide-range PLL for Switching Synchronization in Isolated DC-DC Converters

    Science.gov (United States)

    Fard, Miad

    In this thesis, two Phase-Locked-Loop (PLL) based synchronization schemes are introduced and applied to a bi-directional Dual-Active-Bridge (DAB) dc-dc converter with an input voltage up to 80 V switching in the range of 250 kHz to 1 MHz. The two schemes synchronize gating signals across an isolated boundary without the need for an isolator per transistor. The Power Transformer Sensing (PTS) method utilizes the DAB power transformer to indirectly sense switching on the secondary side of the boundary, while the Digital Isolator Sensing (DIS) method utilizes a miniature transformer for synchronization and communication at up to 100 MHz. The PLL is implemented on-chip, and is used to control an external DAB power-stage. This work will lead to lower cost, high-frequency isolated dc-dc converters needed for a wide variety of emerging low power applications where isolator cost is relatively high and there is a demand for the reduction of parts.

  1. Simulation and Implementation of Quasi Resonant DC-DC Converter

    Directory of Open Access Journals (Sweden)

    N. Devarajan

    2012-01-01

    Full Text Available Problem statement: A half-bridge LLC resonant converter with a voltage doubler rectifier has a simple structure and its Zero-Voltage-Switching (ZVS capability is excellent from zero to full load condition. But conduction loss is more due to high circulating energy thus reducing the system efficiency. Moreover a variable frequency control method makes the control circuits more complicated than those using the Pulse Width Modulation (PWM control method. Thus, DC drive has lower efficiency when it operates on light loads. Approach: To improve the efficiency of the DC drive under light loads, a PWM-controlled quasi-resonant converter is proposed .It has simple control circuits and less conduction loss compared to a half-bridge LLC resonant converter under light load conditions. The proposed converter has a half-bridge LLC resonant converter along with an auxiliary circuit. The load regulation of the proposed converter can be achieved by an auxiliary circuit. Thus the proposed converter is expected to be suitable sustaining power module for the efficiency enhancement of DC drives. As the magnetizing inductance of the proposed converter is larger the circulating energy is considerably reduced under light load conditions. In this study the operational principle, design and modeling of QRC DC-DC converters for DC drives are presented. The PWM controlled quasi resonant converter is implemented using PIC microcontroller 16F184A. Results: The capacitor filter in the output is replaced by pi filter to produce DC with minimum ripple. The experimental results and simulation results are compared. This converter has the advantages like reduced number of switches, reduced transformer and filter size, reduced ripple, reduced switching losses, reduced switching stresses and increased power density. Conclusion: The experimental results closely agree with the simulation results.

  2. Optimization of control sequences for DC-DC-converters; Optimierung der Stellgroessenfolge eines DC-DC-Wandler

    Energy Technology Data Exchange (ETDEWEB)

    Kroeger, Claus [Hochschule Aalen (Germany). Wirtschaftsingenieurwesen

    2009-07-01

    DC-DC-Converters are used in power electronics to adapt different voltage levels of electrical sources and sinks with respect of high efficiency. To minimize electrical losses these power electronic converters always work with switching power semiconductors. This switching principle of the converter is causing a control constraint which limits the achievable performance for the voltage control drastically. This paper presents an optimization for the control sequence in a high dynamic converter control which is based on the dead-beat control design. Thus the non-avoidable control constraint will not be violated. (orig.)

  3. Silicon carbide DC-DC multilevel Cuk converter

    Science.gov (United States)

    Almalaq, Yasser; Alateeq, Ayoob; Matin, Mohammad

    2016-09-01

    In this paper, DC-DC multilevel cuk converter using silicon carbide (SiC) Components is presented. Cuk converter gives output voltage with negative polarity. This topology is useful for applications require high gain with limitation on duty cycle. The gain of the design can be enhanced by increasing the number of multiplier level (N). This relation between the gain and the number of levels is the major advantage of this multilevel cuk converter. In the proposed cuk converter, a single SiC MOSFET, 2N-1 SiC schottky diodes, 2N capacitors, 2 inductors, and single input voltage are used to supply a load with negative polarity. 300V input voltage, 50KHz switching frequency, and 75% duty cycle are the main parameters used in the design. The output parameters are 3KW power and -5.7 KV voltage. Because this design can be used in applications which temperature plays a critical role, the relation between increasing temperature and output voltage and power are tested. The design is simulated using LTspice software and the results are discussed.

  4. Mono-switch AC-DC/DC-DC converter for single-phase UPS%单相UPS的单开关AC-DC/DC-DC变换电路

    Institute of Scientific and Technical Information of China (English)

    李宋; 叶满园; 袁义生

    2011-01-01

    A mono-switch AC-DC/DC-DC converter used in single-phase UPS system is introduced,which consists of one power switch and six diodes. As both AC-DC rectifier and DC-DC booster,its operating modes and working principle are detailed. The single-cycle nonlinear control is adopted,which applies two low-speed PI regulators to control the voltage of two capacitors on DC link and a high-speed PI regulator to control the input current. Simulative results prove that,being simple and reliable,it outputs stable DC bus voltage with high input power factor and low THD.%介绍了一种应用在单相UPS系统中的新型单开关AC-DC/DC-DC变换电路,该电路由1个功率开关器件和6个二极管组成,能够实现AC/DC整流和DC/DC升压2种功能.在详细分析了该电路运行模式及工作原理的基础上,采用了单周期非线性控制理论对其进行控制,利于2个低速PI调节器对直流母线上的2个电容器电压进行控制,1个高速PI调节器对输入电流进行控制.仿真结果表明,该电路简单可靠,输入功率因数高,电流谐波失真小,可以获得稳定的正负直流母线电压.

  5. 基于锂电池化成的新型双向DC/DC拓扑结构研究与建模%Research and Modeling of New Bi-directional DC/DC Topological Structure Based on Lithium Battery

    Institute of Scientific and Technical Information of China (English)

    李少林; 王宜志; 李志斌

    2011-01-01

    A new kind of bi-directional DC/DC topological structure used in the technology of lithium batteries is put for-ward. Adopting two-stage bi-directional DC/DC topological combination ( the half-bridge bi-directional converter and the buck-boost bi-directional converter) , and taking control of buck-boost bi-directional converter by digital signal processor, which can attain the transformation of large voltage differences. The loop simulation of the topological structure of the power circuit can be realized in the environment of Matlab/Simlink. The simulation results show that the converter performance is stahle, and can effectively realize bi-directional transformation between 3 V battery voltage and 400 V bus bar voltage.%提出一种用于锂电池化成技术的新型双向DC/DC拓扑结构.采用两级双向DC/DC拓扑结构,一级使用半桥双向变换器,另一级使用Buck-boost双向变换器,用数字信号处理器对Buck-boost双向变换器进行闭环控制,能实现输入电压和输出电压有较大压差的情况下进行变换.在Matlab/Simlink下对该拓扑结构进行验证.结果表明,该变换器性能稳定,能有效地实现3 V电池电压和400 V母线电压双向变换.

  6. Three-port DC-DC converter with new integrated transformer for DC Distribution Systems

    DEFF Research Database (Denmark)

    Ouyang, Ziwei; Andersen, Michael A. E.

    2014-01-01

    A new integrated transformer for three-port dc-dc converter is proposed to overcome the power coupling effect existed in some known multiple inputs dc-dc converters. Orthogonal primary windings arrangement and in series connection of diagonal secondary Windings enables a fully power decoupling...

  7. A Survey on Voltage Boosting Techniques for Step-Up DC-DC Converters

    DEFF Research Database (Denmark)

    Forouzesh, Mojtaba; Siwakoti, Yam Prasad; Gorji, Saman Asghari;

    2016-01-01

    Step-up dc-dc converters are used to boost the voltage level of the input to a higher output level. Despite of its features such as simplicity of implementation, the fundamental boost dc-dc converter has shortcomings such as low boost ability and low power density. With these limitations, researc...

  8. High power density dc/dc converter: Selection of converter topology

    Science.gov (United States)

    Divan, Deepakraj M.

    1990-01-01

    The work involved in the identification and selection of a suitable converter topology is described. Three new dc/dc converter topologies are proposed: Phase-Shifted Single Active Bridge DC/DC Converter; Single Phase Dual Active Bridges DC/DC Converter; and Three Phase Dual Active Bridges DC/DC Converter (Topology C). The salient features of these topologies are: (1) All are minimal in structure, i.e., each consists of an input and output bridge, input and output filter and a transformer, all components essential for a high power dc/dc conversion process; (2) All devices of both the bridges can operate under near zero-voltage conditions, making possible a reduction of device switching losses and hence, an increase in switching frequency; (3) All circuits operate at a constant frequency, thus simplifying the task of the magnetic and filter elements; (4) Since, the leakage inductance of the transformer is used as the main current transfer element, problems associated with the diode reverse recovery are eliminated. Also, this mode of operation allows easy paralleling of multiple modules for extending the power capacity of the system; (5) All circuits are least sensitive to parasitic impedances, infact the parasitics are efficently utilized; and (6) The soft switching transitions, result in low electromagnetic interference. A detailed analysis of each topology was carried out. Based on the analysis, the various device and component ratings for each topology operating at an optimum point, and under the given specifications, are tabulated and discussed.

  9. Switching coordination of distributed dc-dc converters for highly efficient photovoltaic power plants

    Science.gov (United States)

    Agamy, Mohammed; Elasser, Ahmed; Sabate, Juan Antonio; Galbraith, Anthony William; Harfman Todorovic, Maja

    2014-09-09

    A distributed photovoltaic (PV) power plant includes a plurality of distributed dc-dc converters. The dc-dc converters are configured to switch in coordination with one another such that at least one dc-dc converter transfers power to a common dc-bus based upon the total system power available from one or more corresponding strings of PV modules. Due to the coordinated switching of the dc-dc converters, each dc-dc converter transferring power to the common dc-bus continues to operate within its optimal efficiency range as well as to optimize the maximum power point tracking in order to increase the energy yield of the PV power plant.

  10. Power Network impedance effects on noise emission of DC-DC converters

    Science.gov (United States)

    Esteban, M. C.; Arteche, F.; Iglesias, M.; Gimeno, A.; Arcega, F. J.; Johnson, M.; Cooper, W. E.

    2012-01-01

    The characterization of electromagnetic noise emissions of DC-DC converters is a critical issue that has been analyzed during the desing phase of CMS tracker upgrade. Previous simulation studies showed important variations in the level of conducted emissions when DC-DC converters are loaded/driven by different impedances and power network topologies. Several tests have been performed on real DC-DC converters to validate the Pspice model and simulation results. This paper presents these test results. Conducted noise emissions at the input and at the output terminals of DC-DC converters has been measured for different types of power and FEE impedances. Special attention has been paid to influence on the common-mode emissions by the carbon fiber material used to build the mechanical structure of the central detector. These study results show important recommendations and criteria to be applied in order to decrease the system noise level when integrating the DC-DC.

  11. A Family of Four Quadrant DC/DC Converters with Reduced Number of Components

    DEFF Research Database (Denmark)

    Mostaan, Ali; Soltani, Mohsen

    2015-01-01

    A family of four quadrant DC/DC converters is presented in this paper. Compare with existing four quadrant DC/DC converters that have been introduced in literature, the proposed converters have lower number of components. There are two bidirectional switches, two coupled inductors and one capacit...... effect is minimized in these converters. The effectiveness of the proposed converters is validated with simulation using MATLAB/SIMULINK....

  12. A Fixed-Frequency Bidirectional Resonant DC-DC Converter Suitable for Wide Voltage Gain Range

    DEFF Research Database (Denmark)

    Shen, Yanfeng; Wang, Huai; Al-Durra, Ahmed;

    2017-01-01

    This paper proposes a new bidirectional resonant dc-dc converter suitable for wide voltage gain range applications (e.g., energy storage systems). The proposed converter overcomes the narrow voltage gain range of conventional resonant DC-DC converters, and meanwhile achieves high efficiency...... and characteristics of the proposed converter are analyzed. Finally, a 1-kW converter prototype is built and the experimental results verify the theoretical analyses....

  13. Wide Temperature Range DC-DC Boost Converters for Command/Control/Drive Electronics Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We shall develop wide temperature range DC-DC boost converters that can be fabricated using commercial CMOS foundries. The boost converters will increase the low...

  14. Digitally Controlled 4-Phase Bi-Directional Interleaved Dc-Dc Converter with Coupled Inductors / Digitāli Vadāms 4 Fāžu Divvirziena Līdzstrāvas Pārveidotājs Ar Saistītajām Droselēm

    Science.gov (United States)

    Kroics, K.; Sirmelis, U.; Grigans, L.

    2015-08-01

    The main advantages of multiphase interleaved DC-DC converters over single-phase converters are reduced current stress and reduced output current ripple. Nevertheless, inductor current ripple cannot be reduced only by an interleaving method. The integrated magnetic structure can be used to solve this problem. In this paper, the application of 2-phase coupled inductor designed in a convenient way by using commercially manufactured coil formers and ferrite cores is analysed to develop a 4-phase interleaved DC-DC converter. The steady state phase and output current ripple in a boost mode of the interleaved bidirectional DC-DC converter with integrated magnetics are analysed. The prototype of the converter has been built. The experimental results of the current ripple are presented in the paper. Šajā rakstā piedāvāta magnētiski saistīta drosele, kas izveidota, izmantojot plaša patēriņa ferrīta serdi un tinuma formētāju. Izmantojot šādas droseles, var tikt izveidots vairākfāžu pārveidotājs ar mazām izejas un iejas strāvas pulsācijām, kā arī samazinātām strāvas pulsācijām droselē. Rakstā sīkāk apskatīts līdzstrāvas pārveidotājs, kas sastāv no četrām fāzēm. Šim gadījumam izvestas teorētiskās formulas strāvas pulsāciju aprēķinam, kā arī rakstā parādīti eksperimentālie rezultāti, kas iegūti, testējot prototipu. Teorētiskie rezultāti sakrīt ar eksperimentālajiem

  15. Energy Factor and Mathematical Modeling for Power DC/DC Converters

    Institute of Scientific and Technical Information of China (English)

    Fang Lin LUO; Hong YE

    2004-01-01

    Mathematical modelling for power DC/DC converters is a historical problem accompanying DC/DC conversion technology since 1940's. The traditional mathematical modelling is not available for complex structure converters since the differential equation order increases very high. We have to search other way to establish mathematical modelling for power DC/DC converters. We have theoretically defined a new concept - Energy Factor (EF) in this paper and researched the relations between EF and the mathematical modelling for power DC/DC converters. EF is a new concept in power DC/DC conversion technology, which thoroughly differs from the traditional concepts such as power factor (PF), power transfer efficiency (η), total harmonic distortion (THD) and ripple factor (RF). EF and the subsequential EFv (and EFvD ) can illustrate the system stability, reference response and interference recovery. This investigation is very helpful for system design and DC/DC converters characteristics foreseeing. Two DC/DC converters: Buck converter and Super-Lift Luo-Converter as the samples are analysed in this paper to demonstrate the applications of EF, EFv (and EFvD), PE,SE, VE (and VED ), time constant τ and damping time constant τd .

  16. 独立光伏发电系统中双向变换器的软起动策略%Two-phase soft start strategy for bi-directional DC-DC converter in solar cell stand-alone photovoltaic power system

    Institute of Scientific and Technical Information of China (English)

    张新华; 廖志凌; 杨孟雄

    2009-01-01

    Bi-directional converter applied to solar cell stand-alone photovoltaic power system belongs to the double sources application. Due to complemented operation of switches in bi-directional converter, traditional soft start method will give rise to large inverse inductor current from the output source at double sources application, and result in damage of converter. This paper proposes a novel soft start method-two-phase soft start method to achieve soft start for bi-directional converter of double sources. By implementing soft start of both active switch and passive switch, two-phase soft start method can realize bi-directional converter soft start at double sources application, avoiding inverse inductor current. Two-phase soft start method applies to a series of bi-directional converter. Experimental results are finally given to verify the effectiveness and validity of two-phase soft start method for bi-directional converter of double sources.%双向变换器在太阳能独立光伏发电系统中属于两端"源"的运用场合,采用传统的软起动方法,由于功率开关管互补导通,会从输出端"源"引入反向电感电流,导致变换器损坏.为了实现双向变换器在两端"源"情况下的开机软起动,提出了一种新颖的双向变换器两段式软起动方法,通过对主控管和被控管实施软起动,避免产生反向电感电流,该方法也适用于一族的双向变换器.最后给出了实验结果,验证了两端"源"双向变换器两段式软起动方法的有效性和正确性.

  17. Studies of Interleaved DC-DC Boost Converters with Coupled Inductors

    Science.gov (United States)

    2011-04-01

    power density requirements, interleaved buck and boost converters have been studied in recent years for their potential to improve power converter ...duty ratio of switch S1. Figure 1: Conventional DC-DC Boost Converter Topology (1) Vout/Vin...interleaved DC-DC boost converters with coupled inductors. Included are discussions on a 10kW prototype, a 2kW high temperature prototype, and two 2kW

  18. Chaos analysis and chaotic EMI suppression of DC-DC converters

    CERN Document Server

    Zhang, Bo

    2014-01-01

    Introduces chaos theory, its analytical methods and the means to apply chaos to the switching power supply design DC-DC converters are typical switching systems which have plenty of nonlinear behaviors, such as bifurcation and chaos. The nonlinear behaviors of DC-DC converters have been studied heavily over the past 20 years, yet researchers are still unsure of the practical application of bifurcations and chaos in switching converters. The electromagnetic interference (EMI), which resulted from the high rates of changes of voltage and current, has become a major design criterion in DC-DC co

  19. AC-DC PFC Converter Using Combination of Flyback Converter and Full-bridge DC-DC Converter

    Directory of Open Access Journals (Sweden)

    Moh. Zaenal Efendi

    2014-06-01

    Full Text Available This paper presents a combination of power factor correction converter using Flyback converter and Full-bridge dc-dc converter in series connection. Flyback converter is operated in discontinuous conduction mode so that it can serve as a power factor correction converter and meanwhile Full-bridge dc-dc converter is used for dc regulator. This converter system is designed to produce a 86 Volt of output voltage and 2 A of output current. Both simulation and experiment results show that the power factor of this converter achieves up to 0.99 and meets harmonic standard of IEC61000-3-2. Keywords: Flyback Converter, Full-bridge DC-DC Converter, Power Factor Correction.

  20. High Efficiency Interleaved Active Clamped Dc-Dc Converter with Fuel Cell for High Voltage Applications

    Directory of Open Access Journals (Sweden)

    Sona P

    2014-02-01

    Full Text Available A high efficiency interleaved ZVS active clamped current fed dc-dc converter is proposed in this paper specially used for fuel cell applications. As the fuel cell output is very low we are in need of a step up dc-dc converter. Here a current fed dc-dc converter is used. Two current fed dc-dc converters are interleaved by connecting their inputs in parallel and outputs in series. With this proposed methodology input current ripples in the fuel cell stacks can be reduced and a regulated output voltage ripples can be obtained. The active clamping circuit used in this model absorbs the turn off voltage spikes hence low voltage devices with low on state resistance can be used.Voltage doubler circuits will give double the output voltage than normal with smaller transformer turns ratio and flexibility. The proposed method is simulated in MATLAB for verifying the accuracy of the proposed design.

  1. Modular Power System Configured with Standard Product Hybrid DC-DC Converters Project

    Data.gov (United States)

    National Aeronautics and Space Administration — VPT proposes an innovative concept whereby complex NASA space power electronic systems can be configured using a small number of qualified hybrid DC-DC converter and...

  2. Decentralized Nonlinear Controller Based SiC Parallel DC-DC Converter Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal is aimed at demonstrating the feasibility of a Decentralized Control based SiC Parallel DC-DC Converter Unit (DDCU) with targeted application for...

  3. Control of improved full-bridge three-level DC/DC converter for wind turbines in a DC grid

    DEFF Research Database (Denmark)

    Deng, Fujin; Chen, Zhe

    2013-01-01

    transformer in the IFBTL dc/dc converter. A modulation strategy, including two operation modes, is proposed for the IFBTL dc/dc converter. Then, a voltage balancing control strategy is proposed for the IFBTL dc/dc converter. Furthermore, the control of the wind turbine based on the IFBTL dc/dc converter......This paper presents an improved full-bridge three-level (IFBTL) dc/dc converter for a wind turbine in a dc grid by inserting a passive filter into the dc/dc converter to improve the performance of the converter. The passive filter can effectively reduce the voltage stress of the medium frequency...... in a dc-grid system is presented. Finally, a small-scale IFBTL dc/dc converter prototype was built and tested in the laboratory, and the results verify the theoretical analysis....

  4. Extra-High-Voltage DC-DC Boost Converters Topology with Simple Control Strategy

    Directory of Open Access Journals (Sweden)

    K. Rajambal

    2009-01-01

    Full Text Available This paper presents the topology of operating DC-DC buck converter in boost mode for extra-high-voltage applications. Traditional DC-DC boost converters are used in high-voltage applications, but they are not economical due to the limited output voltage, efficiency and they require two sensors with complex control algorithm. Moreover, due to the effect of parasitic elements the output voltage and power transfer efficiency of DC-DC converters are limited. These limitations are overcome by using the voltage lift technique, opens a good way to improve the performance characteristics of DC-DC converter. The technique is applied to DC-DC converter and a simplified control algorithm in this paper. The performance of the controller is studied for both line and load disturbances. These converters perform positive DC-DC voltage increasing conversion with high power density, high efficiency, low cost in simple structure, small ripples, and wide range of control. Simulation results along theoretical analysis are provided to verify its performance.

  5. Ultra-high Efficiency DC-DC Converter using GaN Devices

    DEFF Research Database (Denmark)

    Ramachandran, Rakesh

    2016-01-01

    The demands for high efficiency dc-dc power converters are increasing day by day in various applications such as telecommunication, data-centers, electric vehicles and various renewable energy systems. Silicon (Si) has been used as the semiconductor material in majority of the power devices...... properties of GaN devices can be utilized in power converters to make them more compact and highly efficient. This thesis entitled “Ultra-high Efficiency DC-DC Converter using GaN devices” focuses on achieving ultra-high conversion efficiency in an isolated dc-dc converter by the optimal utilization of Ga......N devices. Simple replacement of Si or SiC devices with GaN devices in the converter will not give an expected increase in efficiency or any improvement in the performance of the converter. The use of GaN devices has defined another dimension in the design of power converters, which mainly deals...

  6. Simulation and Implementation of Interleaved Boost DC-DC Converter for Fuel Cell Application

    Directory of Open Access Journals (Sweden)

    Ahmad Saudi Samosir

    2011-10-01

    Full Text Available This paper deals with a boost dc-dc converter for fuel cell application. In fuel cell electric vehicles application, a high power boost dc-dc converter is adopted to adjust the output voltage, current and power of fuel cell engine to meet the vehicle requirements. One of challenge in designing a boost converter for high power application is how to handle the high current at the input side. In this paper an interleaved boost dc-dc converter is proposed for current sharing on high power application. Moreover, this converter also reduces the fuel ripple current. Performance of the interleaved boost converter is tested through simulation and experimental results. Keywords: component; Interleaved Boost Converter; Fuel Cell Electric Vehicle; high power application.  

  7. Interleaved DC-DC Converter with Discrete Duty Cycle and Open Loop Control

    Science.gov (United States)

    Kroics, K.; Sokolovs, A.

    2016-08-01

    The authors present the control principle of the multiphase interleaved DC-DC converter that can be used to vastly reduce output current ripple of the converter. The control algorithm can be easily implemented by using microcontroller without current loop in each phase. The converter works in discontinuous conduction mode (DCM) but close to boundary conduction mode (BCM). The DC-DC converter with such a control algorithm is useful in applications that do not require precise current adjustment. The prototype of the converter has been built. The experimental results of the current ripple are presented in the paper.

  8. Interleaved DC-DC Converter with Discrete Duty Cycle and Open Loop Control

    Directory of Open Access Journals (Sweden)

    Kroics K.

    2016-08-01

    Full Text Available The authors present the control principle of the multiphase interleaved DC-DC converter that can be used to vastly reduce output current ripple of the converter. The control algorithm can be easily implemented by using microcontroller without current loop in each phase. The converter works in discontinuous conduction mode (DCM but close to boundary conduction mode (BCM. The DC-DC converter with such a control algorithm is useful in applications that do not require precise current adjustment. The prototype of the converter has been built. The experimental results of the current ripple are presented in the paper.

  9. Analysis of high voltage step-up nonisolated DC-DC boost converters

    Science.gov (United States)

    Alisson Alencar Freitas, Antônio; Lessa Tofoli, Fernando; Junior, Edilson Mineiro Sá; Daher, Sergio; Antunes, Fernando Luiz Marcelo

    2016-05-01

    A high voltage step-up nonisolated DC-DC converter based on coupled inductors suitable to photovoltaic (PV) systems applications is proposed in this paper. Considering that numerous approaches exist to extend the voltage conversion ratio of DC-DC converters that do not use transformers, a detailed comparison is also presented among the proposed converter and other popular topologies such as the conventional boost converter and the quadratic boost converter. The qualitative analysis of the coupled-inductor-based topology is developed so that a design procedure can be obtained, from which an experimental prototype is implemented to validate the theoretical assumptions.

  10. Nonlinear Phenomena and Resonant Parametric Perturbation Control in QR-ZCS Buck DC-DC Converters

    Science.gov (United States)

    Hsieh, Fei-Hu; Liu, Feng-Shao; Hsieh, Hui-Chang

    The purpose of this study is to investigate the chaotic phenomena and to control in current-mode controlled quasi-resonant zero-current-switching (QR-ZCS) DC-DC buck converters, and to present control of chaos by resonant parametric perturbation control methods. First of all, MATLAB/SIMULINK is used to derive a mathematical model for QR-ZCS DC-DC buck converters, and to simulate the converters to observe the waveform of output voltages, inductance currents and phase-plane portraits from the period-doubling bifurcation to chaos by changing the load resistances. Secondly, using resonant parametric perturbation control in QR-ZCS buck DC-DC converters, the simulation results of the chaotic converter form chaos state turn into stable state period 1, and improve ripple amplitudes of converters under the chaos, to verify the validity of the proposes method.

  11. Study on the Control Algorithm of Two-Stage DC-DC Converter for Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Changhao Piao

    2014-01-01

    Full Text Available The fast response, high efficiency, and good reliability are very important characteristics to electric vehicles (EVs dc/dc converters. Two-stage dc-dc converter is a kind of dc-dc topologies that can offer those characteristics to EVs. Presently, nonlinear control is an active area of research in the field of the control algorithm of dc-dc converters. However, very few papers research on two-stage converter for EVs. In this paper, a fixed switching frequency sliding mode (FSFSM controller and double-integral sliding mode (DISM controller for two-stage dc-dc converter are proposed. And a conventional linear control (lag is chosen as the comparison. The performances of the proposed FSFSM controller are compared with those obtained by the lag controller. In consequence, the satisfactory simulation and experiment results show that the FSFSM controller is capable of offering good large-signal operations with fast dynamical responses to the converter. At last, some other simulation results are presented to prove that the DISM controller is a promising method for the converter to eliminate the steady-state error.

  12. Test Results of Selected Commercial DC/DC Converters under Cryogenic Temperatures - A Digest

    Science.gov (United States)

    Patterson, Richard; Hammoud, Ahmad

    2010-01-01

    DC/DC converters are widely used in space power systems in the areas of power management and distribution, signal conditioning, and motor control. Design of DC/DC converters to survive cryogenic temperatures will improve the power system performance, simplify design, and reduce development and launch costs. In this work, the performance of nine COTS modular, low-tomedium power DC/DC converters was investigated under cryogenic temperatures. The converters were evaluated in terms of their output regulation, efficiency, and input and output currents. At a given temperature, these properties were obtained at various input voltages and at different load levels. A summary on the performance of the tested converters was given. More comprehensive testing and in-depth analysis of performance under long-term exposure to extreme temperatures are deemed necessary to establish the suitability of these and other devices for use in the harsh environment of space exploration missions.

  13. Efficient and ripple-mitigating dc-dc converter for residential fuel cell system

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yong [Danfoss Solar Inverters, Hardware, Jyllandsgade 28, 6400 Soenderborg (Denmark); Choi, Seeyoung [Digital Appliance Division, Samsung Electronics Co. Ltd., Maetan-3Dong, Suwon, Gyeonggi (Korea); Lee, Eunchul [Willings Co. Ltd., SK Ventium, 522 Dangjung-Dong, Gunpo-Si, Gyeonggi-Do (Korea)

    2009-01-15

    Proton exchange membrane fuel cell (PEMFC) systems for residential application require efficient and ripple-mitigating power conditioning system (PCS). The key point to reach it, is the design and control of the dc-dc converter. Based on the theoretical and experimental analysis of the traditional converter, this paper proposes a novel parallel-series full bridge (P-SFB) dc-dc converter, and improves its phase shifting scheme. This paper also proposes a novel controller for low frequency ripple current suppressing applied on the converter. The experimental results verify that, the dc-dc converter achieves a peak efficiency of 95.5%. Therefore PCS's maximum efficiency reaches 92.9%. And the input current ripple is reduced significantly with the new controller. (author)

  14. Efficiency and Regulation of Commercial Low Power DC/DC Converter Modules at Low Temperatures

    Science.gov (United States)

    Elbuluk, Malik E.; Gerber, Scott; Hammoud, Ahmad; Patterson, Richard L.

    2000-01-01

    DC/DC converters that are capable of operating at cryogenic temperatures are anticipated to play an important role in the power systems of future NASA deep space missions. Design of these converters to survive cryogenic temperatures will improve the power system performance, and reduce development and launch costs. At the NASA Glenn Research Center Low Temperature Electronics Laboratory, several commercial off-the-shelf dc/dc converter modules were evaluated for their low temperature performance. Various parameters were investigated as a function of temperature, in the range of 20 C to -190 C. Data pertaining to the efficiency and voltage regulation of the tested converters is presented and discussed.

  15. Design of the DC-DC power stage of the capacitor charger for MAXIDISCAP power converters

    CERN Document Server

    Cravero, Jean-Marc

    2013-01-01

    This technical report presents the design of the DC-DC power stage of the capacitor charger for MAXIDISCAP power converters. The power stage is based on a half bridge series resonant converter in Discontinuous Conduction Mode (DCM). This simple and robust topology allows obtaining a current source behavior with a low switching losses power stage. The associated control stage is implemented using a commercial controller which has differenti nternal circuits that allows a high integration of the converter control system. The report presents the design and tuning criteria for the DC-DC converter, including the power stage and the control system.

  16. Robust DC/DC converter control for polymer electrolyte membrane fuel cell application

    Science.gov (United States)

    Wang, Ya-Xiong; Yu, Duck-Hyun; Chen, Shi-An; Kim, Young-Bae

    2014-09-01

    This study investigates a robust controller in regulating the pulse width modulation (PWM) of a DC/DC converter for a polymer electrolyte membrane fuel cell (PEMFC) application. A significant variation in the output voltage of a PEMFC depends on the power requirement and prevents a PEMFC from directly connecting to a subsequent power bus. DC/DC converters are utilized to step-up or step-down voltage to match the subsequent power bus voltage. In this study, a full dynamic model, which includes a PEMFC and boost and buck DC/DC converters, is developed under MATLAB/Simulink environment for control. A robust PWM duty ratio control for the converters is designed using time delay control (TDC). This control enables state variables to accurately follow the dynamics of a reference model using time-delayed information of plant input and output information within a few sampling periods. To prove the superiority of the TDC performance, traditional proportional-integral control (PIC) and model predictive control (MPC) are designed and implemented, and the simulation results are compared. The efficacies of TDC for the PEMFC-fed PWM DC/DC converters are validated through experimental test results using a 100 W PEMFC as well as boost and buck DC/DC converters.

  17. A Novel Quasi-SEPIC High-Voltage Boost DC-DC Converter

    DEFF Research Database (Denmark)

    Siwakoti, Yam Prasad; N. Soltani, Mohsen; Mostaan, Ali;

    2017-01-01

    This paper proposes a modified coupled-inductor SEPIC dc-dc converter for low power and high voltage gain applications such as for piezoelectric drive systems. The converter uses the same components as of SEPIC converter with an additional diode. Compared to conventional topologies with similar v...

  18. Novel bidirectional DC-DC converters based on the three-state switching cell

    Science.gov (United States)

    da Silva Júnior, José Carlos; Robles Balestero, Juan Paulo; Lessa Tofoli, Fernando

    2016-05-01

    It is well known that there is an increasing demand for bidirectional DC-DC converters for applications that range from renewable energy sources to electric vehicles. Within this context, this work proposes novel DC-DC converter topologies that use the three-state switching cell (3SSC), whose well-known advantages over conventional existing structures are ability to operate at high current levels, while current sharing is maintained by a high frequency transformer; reduction of cost and dimensions of magnetics; improved distribution of losses, with consequent increase of global efficiency and reduction of cost associated to the need of semiconductors with lower current ratings. Three distinct topologies can be derived from the 3SSC: one DC-DC converter with reversible current characteristic able to operate in the first and second quadrants; one DC-DC converter with reversible voltage characteristic able to operate in the first and third quadrants and one DC-DC converter with reversible current and voltage characteristics able to operate in four quadrants. Only the topology with bidirectional current characteristic is analysed in detail in terms of the operating stages in both nonoverlapping and overlapping modes, while the design procedure of the power stage elements is obtained. In order to validate the theoretical assumptions, an experimental prototype is also implemented, so that relevant issues can be properly discussed.

  19. Application handbook for a Standardized Control Module (SCM) for DC-DC converters, volume 1

    Science.gov (United States)

    Lee, F. C.; Mahmoud, M. F.; Yu, Y.

    1980-01-01

    The standardized control module (SCM) was developed for application in the buck, boost and buck/boost DC-DC converters. The SCM used multiple feedback loops to provide improved input line and output load regulation, stable feedback control system, good dynamic transient response and adaptive compensation of the control loop for changes in open loop gain and output filter time constraints. The necessary modeling and analysis tools to aid the design engineer in the application of the SCM to DC-DC Converters were developed. The SCM functional block diagram and the different analysis techniques were examined. The average time domain analysis technique was chosen as the basic analytical tool. The power stage transfer functions were developed for the buck, boost and buck/boost converters. The analog signal and digital signal processor transfer functions were developed for the three DC-DC Converter types using the constant on time, constant off time and constant frequency control laws.

  20. DC-DC converters with reduced mass for trackers at the HL-LHC

    Science.gov (United States)

    Affolder, A.; Allongue, B.; Blanchot, G.; Faccio, F.; Fuentes, C.; Greenall, A.; Michelis, S.

    2011-11-01

    The development at CERN of low noise DC-DC converters for the powering of front-end systems enables the implementation of efficient powering schemes for the physics experiments at the HL-LHC. Recent tests made on the ATLAS short strip tracker modules confirm the full electromagnetic compatibility of the DC-DC converter prototypes with front-end detectors. The integration of the converters in the trackers front-ends needs to address also the material budget constraints. The impact of the DC-DC converters onto the material budget of the ATLAS tracker modules is discussed and mass reduction techniques are explored, leading to a compromise between electromagnetic compatibility and mass. Low mass shield implementations and Aluminum core inductors are proposed. Also, the impact on emitted noise due to a size reduction of critical components is discussed. Finally, material reduction techniques are discussed at the board layout and manufacturing levels.

  1. Critical conditions of saddle-node bifurcations in switching DC-DC converters

    Science.gov (United States)

    Fang, Chung-Chieh

    2013-08-01

    Although existence of multiple periodic orbits in some DC-DC converters have been known for decades, linking the multiple periodic orbits with the saddle-node bifurcation (SNB) is rarely reported. The SNB occurs in popular DC-DC converters, but it is generally reported as a strange instability. Recently, design-oriented instability critical conditions are of great interest. In this article, average, sampled-data and harmonic balance analyses are applied and they lead to equivalent results. Many new critical conditions are derived. They facilitate future research on the instability associated with multiple periodic orbits, sudden voltage jumps or disappearances of periodic orbits observed in DC-DC converters. The effects of various converter parameters on the instability can be readily seen from the derived critical conditions. New Nyquist-like plots are also proposed to predict or prevent the occurrence of the instability.

  2. A Component-Reduced Zero-Voltage Switching Three-Level DC-DC Converter

    DEFF Research Database (Denmark)

    Qin, Zian; Pang, Ying; Wang, Huai;

    2016-01-01

    The basic Zero-Voltage Switching (ZVS) three-level DC-DC converter has one clamping capacitor to realize the ZVS of the switches, and two clamping diodes to clamp the voltage of the clamping capacitor. In order to reduce the reverse recovery loss of the diode as well as its cost, this paper...... proposes to remove one of the clamping diodes in basic ZVS three-level DC-DC converter. With less components, the proposed converter can still have a stable clamping capacitor voltage, which is clamped at half of the dc link voltage. Moreover, the ZVS performance will be influenced by removing the clamping...

  3. High power density dc/dc converter: Component selection and design

    Science.gov (United States)

    Divan, Deepakraj M.

    1989-01-01

    Further work pertaining to design considerations for the new high power, high frequency dc/dc converters is discussed. The goal of the project is the development of high power, high power density dc/dc converters at power levels in the multi-kilowatt to megawatt range for aerospace applications. The prototype converter is rated for 50 kW at a switching frequency of 50 kHz, with an input voltage of 200 Vdc and an output of 2000 Vdc. The overall power density must be in the vicinity of 0.2 to 0.3 kg/kW.

  4. Elimination of output voltage oscillations in DC-DC converter using PWM with PI controller

    Directory of Open Access Journals (Sweden)

    Sreenivasappa Veeranna Bhupasandra

    2010-01-01

    Full Text Available In this paper the SIMULINK model of a PWM controlled DC-DC converter is modeled using switching function concept to control the speed of the DC motor. The presence of the voltage oscillation cycles due to higher switching frequency in the DC-DC converter is identified. The effect of these oscillations on the output voltage of the converter, Armature current, Developed torque and Speed of the DC motor is analyzed. In order to minimize the oscillation cycles the PI controller is proposed in the PWM controller.

  5. Novel Step-Up DC/DC Converter with No Right Half Plane Zero and Reduced Switched Voltage Stress Characteristics

    DEFF Research Database (Denmark)

    Mostaan, Ali; Alizadeh, Ebrahim; Soltani, Mohsen

    2014-01-01

    Novel step-up DC/DC converter is introduced in this paper. This converter is realized with adding the switched capacitor voltage multiplier cell to the three switch step-down DC/DC converter that has been proposed in the literature. The proposed converter is analyzed in the steady state and the v...

  6. Design of current source DC/DC converter and inverter for 2kW fuel cell application

    DEFF Research Database (Denmark)

    Andreiciks, A.; Steiks, I.; Krievs, O.

    2013-01-01

    of a DC/DC converter and an inverter. In this paper a detailed simulation study of such interfacing converter system comprising a double inductor push-pull step-up DC/DC converter and a cascaded H-bridge inverter has been carried out and further confirmed with experimental results. The power converter...

  7. Optimized photovoltaic generator-water electrolyser coupling through a controlled DC-DC converter

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Valverde, R.; Miguel, C.; Urbina, A. [Universidad Politecnica de Cartagena, Departamento de Electronica, Tecnologia de Computadoras y Proyectos, Plaza del Hospital, 1, Cartagena, 30203 Murcia (Spain); Martinez-Bejar, R. [Universidad de Murcia, Departamento de Ingenieria de la Informacion y las Comunicaciones, Facultad de Informatica, Campus de Espinardo, 30071 Murcia (Spain)

    2008-10-15

    The coupling of a photovoltaic generator and an electrolyser is one of the most promising options for obtaining hydrogen from a renewable energy source. Both are well known technologies, however, since the high variability of the solar radiation, an efficient coupling still presents some challenges. Direct or through a DC-DC converter couplings are the options in isolated applications. In this work, three models, respectively, for a photovoltaic (PV) generator, a controlled DC-DC converter and a complete proton exchange membrane (PEM) electrolyser have been designed by using Matlab/Simulink. A PV-electrolyser specific algorithm to search for the optimum and safe working point for both elements is presented. Simulation results demonstrate that the use of a controlled DC-DC converter with the proposed algorithm shows better adaptability to the variable radiation conditions than the other coupling options. Therefore, it leads to a better compliance between the electrolyser and the sizing of the PV generator. (author)

  8. Advanced DC/DC Converters Towards Higher Volumetric Efficiencies For Space Applications

    Science.gov (United States)

    Shaw, Harry; Shue, Jack; Liu, David; Wang, Bright; Plante, Jeanette

    2005-01-01

    A new emphasis on planetary exploration by NASA drives the need for small, high power DC/DC converters which are functionally modular. NASA GSFC and other government space organizations are supporting technology development in the DC/DC converter area to both meet new needs and to promote more sources of supply. New technologies which enable miniaturization such as embedded passive technologies and thermal management using high thermal conductivity materials are features of the new designs. Construction of some simple DC/DC converter core circuits using embedded components was found to be successful for increasing volumetric efficiency to 37 W/inch. The embedded passives were also able to perform satisfactorily in this application in cryogenic temperatures.

  9. Controlling DC-DC converters by chaos-based pulse width modulation to reduce EMI

    Energy Technology Data Exchange (ETDEWEB)

    Li Hong [Department of Mathematics and Computer Science, FernUniversitaet in Hagen, 58084 Hagen (Germany)], E-mail: hong.li@FernUni-Hagen.de; Zhang Bo [School of Electric Power, South China University of Technology, Guangzhou (China); Li Zhong; Halang, Wolfgang A. [Department of Mathematics and Computer Science, FernUniversitaet in Hagen, 58084 Hagen (Germany); Chen Guanrong [Department of Electronic Engineering, City University of Hong Kong, Hong Kong (China)

    2009-11-15

    In this paper, periodic and chaotic behaviors of DC-DC converters under certain parametric conditions are simulated, experimentally verified, and analyzed. Motivated by the work of J.H.B. Deane and D.C. Hamill in 1996, where chaotic phenomena are useful in suppressing electromagnetic interference (EMI) by adjusting the parameters of the DC-DC converter and making it operate in chaos, a chaos-based pulse width modulation (CPWM) is proposed to distribute the harmonics of the DC-DC converters continuously and evenly over a wide frequency range, thereby reducing the EMI. The output waves and spectral properties of the EMI are simulated and analyzed as the carrier frequency or amplitude changes with regard to different chaotic maps. Simulation and experimental results are given to illustrate the effectiveness of the proposed CPWM, which provides a good example of applying chaos theory in engineering practice.

  10. Modelling and Simulation of Digital Compensation Technique for dc-dc Converter by Pole Placement

    Science.gov (United States)

    Shenbagalakshmi, R.; Sree Renga Raja, T.

    2015-09-01

    A thorough and effective analysis of the dc-dc converters is carried out in order to achieve the system stability and to improve the dynamic performance. A small signal modelling based on state space averaging technique for dc-dc converters is carried out. A digital state feedback gain matrix is derived by pole placement technique in order to achieve the stability of a completely controllable system. A prediction observer for the dc-dc converters is designed and a dynamic compensation (observer plus control law) is provided using separation principle. The output is very much improved with zero output voltage ripples, zero peak overshoot, and much lesser settling time in the range of ms and with higher overall efficiency (>90 %).

  11. Determination of input/output characteristics of full-bridge AC/DC/DC converter for arc welding

    OpenAIRE

    Stefanov, Goce; Karadzinov, Ljupco; Sarac, Vasilija; Cingoski, Vlatko; Gelev, Saso

    2016-01-01

    This paper describes the design and practical implementation of AC/DC/DC converter in mode of arc welding. An analysis of the operation of AC/DC/DC converter and its input/output characteristics are determined with computer simulations. The practical part is consisted of AC/DC/DC converter prototype for arc welding with output power of 3 kW and switching frequency of 64 kHz. The operation of AC/DC/DC converter is validated with experimental measurements.

  12. Modelling, Simulation and Construction of a DC/DC Boost Power Converter: A School Experimental System

    Science.gov (United States)

    Silva-Ortigoza, R.; Silva-Ortigoza, G.; Hernandez-Guzman, V. M.; Saldana-Gonzalez, G.; Marcelino-Aranda, M.; Marciano-Melchor, M.

    2012-01-01

    We introduce a dc/dc boost power converter as a didactic prototype intended to support courses on electric circuit analysis experimentally. The corresponding mathematical model is obtained, the converter is designed and an experimental setup is described, constructed and tested. Simplicity of construction as well as low cost of components renders…

  13. Five-Level Active-Neutral-Point-Clamped DC/DC Converter

    DEFF Research Database (Denmark)

    Liu, Dong; Deng, Fujin; Chen, Zhe

    Multi-level converters are getting more and more attentions because of their obvious merits such as lower voltage stress and harmonic, smaller size of output filters, and so on. In this paper, a five-level active-neutral-point-clamped (5L-ANPC) dc/dc converter is proposed for power transfer...

  14. Single Event Burnout in DC-DC Converters for the LHC Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Claudio H. Rivetta et al.

    2001-09-24

    High voltage transistors in DC-DC converters are prone to catastrophic Single Event Burnout in the LHC radiation environment. This paper presents a systematic methodology to analyze single event effects sensitivity in converters and proposes solutions based on de-rating input voltage and output current or voltage.

  15. Comparative efficiency evaluation of buck and hybrid buck DC-DC converters for automotive applications

    DEFF Research Database (Denmark)

    Pelan, Ovidiu; Cornea, Octavian; Muntean, Nicolae

    2014-01-01

    This paper presents and discusses design considerations and efficiency investigation of a conventional step-down and a hybrid switched-capacitor DC-DC converter. Three MOSFETs with low on-resistance have been tested for each converter in order to find the most adequate switch for this application...

  16. A Bidirectional Multi-Port DC-DC Converter Integrating Voltage Equalizer

    DEFF Research Database (Denmark)

    Chen, Jianfei; Hou, Shiying; Deng, Fujin

    2015-01-01

    with a uniform voltage level while eliminating the voltage imbalance. In addition, high step-down and step-up ratios with low component voltage stress can be achieved in the proposed converter. A bidirectional four-port dc-dc converter is presented to do theoretical analysis for the voltage equalization of three...

  17. Soft switching bidirectional DC-DC converter for ultracapacitor-batteries interface

    Energy Technology Data Exchange (ETDEWEB)

    Adib, Ehsan; Farzanehfard, Hosein [Dept. of Electrical and Computer Engineering, Isfahan Univ. of Technology (Iran)

    2009-12-15

    In this paper a new soft switching bidirectional DC-DC converter is introduced which can be applied as the interface circuit between ultracapacitors and batteries or fuel cells. All semiconductor devices in the proposed converter are soft switched while the control circuit remains PWM. Due to achieved soft switching condition, the energy conversion through the proposed converter is highly efficient. The proposed converter is analyzed and a prototype converter is implemented. The presented experimental results confirm the theoretical analysis. (author)

  18. High Current Planar Magnetics for High Efficiency Bidirectional DC-DC Converters for Fuel Cell Applications

    DEFF Research Database (Denmark)

    Pittini, Riccardo; Zhang, Zhe; Andersen, Michael A. E.

    2014-01-01

    Efficiency is one of the main concerns during the design phase of switch mode power supply. Planar magnetics based on PCB windings have the potential to reduce the magnetic manufacturing cost however, one of their main drawbacks comes from their low filling factor and high stray capacitance...... complexity and challenges. The analysis is focused on a high current inductor for a dc-dc converter for fuel cell applications and it is based on FEM simulations. Analysis and results are verified on a 6 kW dc-dc isolated full bridge boost converter prototype based on fully planar magnetics achieving a peak...

  19. Model predictive control of bidirectional isolated DC-DC converter for energy conversion system

    Science.gov (United States)

    Akter, Parvez; Uddin, Muslem; Mekhilef, Saad; Tan, Nadia Mei Lin; Akagi, Hirofumi

    2015-08-01

    Model predictive control (MPC) is a powerful and emerging control algorithm in the field of power converters and energy conversion systems. This paper proposes a model predictive algorithm to control the power flow between the high-voltage and low-voltage DC buses of a bidirectional isolated full-bridge DC-DC converter. The predictive control algorithm utilises the discrete nature of the power converters and predicts the future nature of the system, which are compared with the references to calculate the cost function. The switching state that minimises the cost function is selected for firing the converter in the next sampling time period. The proposed MPC bidirectional DC-DC converter is simulated with MATLAB/Simulink and further verified with a 2.5 kW experimental configuration. Both the simulation and experimental results confirm that the proposed MPC algorithm of the DC-DC converter reduces reactive power by avoiding the phase shift between primary and secondary sides of the high-frequency transformer and allow power transfer with unity power factor. Finally, an efficiency comparison is performed between the MPC and dual-phase-shift-based pulse-width modulation controlled DC-DC converter which ensures the effectiveness of the MPC controller.

  20. Design and Control of a Multiple Input DC/DC Converter for Battery/Ultra-capacitor Based Electric Vehicle Power System

    DEFF Research Database (Denmark)

    Schaltz, Erik; Li, Zhihao; Onar, Omer;

    2009-01-01

    Battery/Ultra-capacitor based electrical vehicles (EV) combine two energy sources with different voltage levels and current characteristics. This paper focuses on design and control of a multiple input DC/DC converter, to regulate output voltage from different inputs. The proposed multi-input con......Battery/Ultra-capacitor based electrical vehicles (EV) combine two energy sources with different voltage levels and current characteristics. This paper focuses on design and control of a multiple input DC/DC converter, to regulate output voltage from different inputs. The proposed multi......-input converter is capable of bi-directional operation and is responsible for power diversification and optimization. A fixed switching frequency strategy is considered to control its operating modes. A portion of New York City Cycle that includes these operation modes is used to perform the analyses....

  1. Studi Komparasi Fungsi Keanggotaan Fuzzy sebagai Kontroler Bidirectional DC-DC Converter pada Sistem Penyimpan Energi

    Directory of Open Access Journals (Sweden)

    Eka Prasetyono

    2015-09-01

    Full Text Available Bidirectional DC-DC converter is needed in the energy storage system. The converter topology used in this paper was a non-isolated bidirectional DC-DC buck-boost converter. This converter worked in two ways, which the charging mode stored energy into battery when load current was less than nominal main DC current (set point and discharging mode transferred energy from battery to the load when its current exceeded set point value. Both of these modes worked automatically according to the load current. The charging and discharging currents were controlled by fuzzy logic controller which was implemented on microcontroller ARM Cortex-M4F STM32F407VG. This paper compares two types of fuzzy membership function (triangular and sigmoid in controlling bidirectional DC-DC converter. The results showed that fuzzy logic controller with triangle membership function and sigmoid as control bidirectional DC-DC converter had no significant different response, both had an average error for charging and discharging process under 4% with ripple current on the main DC bus around 0.5%. The computing time of program for fuzzy logic controller with triangular membership functions had 19.01% faster than sigmoid, and fuzzy logic computation time on a microcontroller with hardware floating point was 60% faster than software floating point.

  2. A New Sliding Mode Controller for DC/DC Converters in Photovoltaic Systems

    Directory of Open Access Journals (Sweden)

    M. Sarvi

    2013-01-01

    Full Text Available DC/DC converters are widely used in many industrial and electrical systems. As DC/DC converters are nonlinear and time-variant systems, the application of linear control techniques for the control of these converters is not suitable. In this paper, a new sliding mode controller is proposed as the indirect control method and compared to a simple direct control method in order to control a buck converter in photovoltaic applications. The solar arrays are dependent power sources with nonlinear voltage-current characteristics under different environmental conditions (insolation and temperature. From this point of view, the DC/DC converter is particularly suitable for the application of the sliding mode control in photovoltaic application, because of its controllable states. Simulations are performed in Matlab/Simulink software. The simulation results are presented for a step change in reference voltage and input voltage as well as step load variations. The simulations results of proposed method are compared with the conventional PID controller. The results show the good performance of the proposed sliding mode controller. The proposed method can be used for the other DC/DC converter.

  3. Custom DC-DC converters for distributing power in SLHC trackers

    CERN Document Server

    Allongue, B; Blanchot, G; Faccio, F; Fuentes, C; Mattavelli, P; Michelis, S; Orlandis, S; Spiazzi, G

    2008-01-01

    A power distribution scheme based on the use of on-board DC-DC converters is proposed to efficiently distribute power to the on-detector electronics of SLHC trackers. A comparative analysis of different promising converter topologies is presented, leading to the choice of a magneticbased buck converter as a first conversion stage followed by an on-chip switched capacitors converter. An overall efficiency above 80% is estimated for the practical implementation proposed.

  4. DC/DC converters for integration of double-layer condensers in onboard power supply; DC/DC-Wandler zur Einbindung von Doppelschichtkondensatoren in das Fahrzeugenergiebordnetz

    Energy Technology Data Exchange (ETDEWEB)

    Polenov, Dieter

    2010-01-15

    The paper discusses DC/DC converters for integration of double layer condensers into the onboard power system. First, requirements on DC/DC converters are listed and compared on the basis of three exemplary applications. A DC/DC converter concept is developed for decoupling transient high-power loads like electric steering systems. Three different topologies are compared using a specially developed method in order to find the best solution for the given application. In order to establish adequate criteria for selecting the switching frequency and inductivities of storage throttles, the influence of the trottle power change on the switching characteristics of the MOSFETs and on certain ranges of EMP interference emissions is investigated. As methods of optimising the operation of the synchronous rectifiers, parallel connection of Schottky diodes and synchronous rectifiers as well as the variation of the shut-off dead times of synchronous rectifiers were investigated. Further, a concept for converter control was developed in consideration of the intended application and topology. Finally, selected aspects for implementation of the DC/DC converter concept are presented as well as the results of experimental investigations.

  5. A high voltage gain quasi Z-source isolated DC/DC converter

    DEFF Research Database (Denmark)

    Siwakoti, Yam P.; Blaabjerg, Frede; Loh, Poh Chiang

    2014-01-01

    A compact quasi-Z-source DC/DC converter is presented with high voltage gain, isolated output, and improved efficiency. The improvements in size and performance were achieved by using a square wave inverter with only two output switches driving an isolating transformer in push-pull mode, followed...

  6. DC-DC converter with a wide load range and a wide input-voltage range

    NARCIS (Netherlands)

    Ting, Y.

    2015-01-01

    This thesis investigated the possibility of increasing the efficiency of a DC-DC converter over a wide load range and a wide input-voltage range based on the Single Active Bridge (SAB) topology with two approaches. The first approach involved making changes to the topology whereas the second made us

  7. Interleaved Self-Oscillating Class E Derived Resonant DC/DC Converters

    DEFF Research Database (Denmark)

    Kovacevic, Milovan; Knott, Arnold; Andersen, Michael A. E.

    2012-01-01

    A new method for achieving self-oscillating, self-interleaved operation of class E derived resonant DC/DC converters is presented. The proposed method is suitable for operation at frequencies in the Very High Frequency (VHF) band. Interleaved and self-oscillating modes of operation are achieved...

  8. A VHF Class E DC-DC Converter with Self-Oscillating Gate Driver

    DEFF Research Database (Denmark)

    Andersen, Toke Meyer; Christensen, Søren K.; Knott, Arnold

    2011-01-01

    This paper describes the analysis and design of a DC-DC converter topology which is operational at frequencies in the Very High Frequency (VHF) band ranging from 30 MHz − 300 MHz. The presented topology, which consists of a class E inverter, class E rectifier, and self-oscillating gate driver, is...

  9. Analysis of DC/DC Converter Efficiency for Energy Storage System Based on Bidirectional Fuel Cells

    DEFF Research Database (Denmark)

    Pittini, Riccardo; Zhang, Zhe; Andersen, Michael A. E.

    2013-01-01

    Renewable energy sources are fluctuating depending on the availability of the energy source. For this reason, energy storage is becoming more important and bidirectional fuel cells represent an attractive technology. Fuel cells require highcurrent low-voltage dc-dc or dc-ac converters as power...

  10. Area-Efficiency Trade-Offs in Integrated Switched-Capacitor DC-DC Converters

    DEFF Research Database (Denmark)

    Spliid, Frederik Monrad; Larsen, Dennis Øland; Knott, Arnold

    2016-01-01

    This paper analyzes the relationship between efficiency and chip area in a fully integrated switched capacitor voltage divider dc-dc converter implemented in 180nm-technology and a 1/2 topology. A numerical algorithm for choosing the optimal sizes of individual components, in terms of power loss,...

  11. Quasiperiodicity and Torus Breakdown in a Power Electronic DC/DC Converter

    DEFF Research Database (Denmark)

    Zhusubaliyev, Zhanybai; Soukhoterin, Evgeniy; Mosekilde, Erik

    2007-01-01

    This paper discusses the mechanisms of torus formation and torus destruction in a dc/dc converter with relay control and hysteresis. We establish a chart of the dynamical modes in the input voltage versus load resistance parameter plane. This chart displays several different torus bifurcations...

  12. Characterization of diode valve in medium voltage dc/dc converter for wind turbines

    DEFF Research Database (Denmark)

    Dincan, Catalin Gabriel; Kjær, Philip Carne

    2016-01-01

    This paper proposes a methodology for characterization of medium voltage (MV), medium frequency (MF) rectifier diode valve. The intended application is for 10MW dc/dc converters used in DC offshore wind turbines. Sensitivity to semiconductor component parameter variation, snubber component...

  13. Multistability and hidden attractors in a multilevel DC/DC converter

    DEFF Research Database (Denmark)

    Zhusubaliyev, Zhanybai T.; Mosekilde, Erik

    2015-01-01

    for the hidden set in most cases has been so complicated that special analytic and/or numerical techniques have been required to locate the set. By simulating the model of a multilevel DC/DC converter that operates in the regime of high feedback gain, the paper illustrates how pulse-width modulated control can...

  14. Computer-aided analysis and simulation of switched dc-dc converters

    Science.gov (United States)

    Lee, F. C.; Yu, Y.

    1978-01-01

    State space techniques are employed to derive an equivalent nonlinear recurrent time-domain model that describes the switched dc-dc converter behavior exactly. This model is employed effectively to analyze both large signal behavior by propagating the recurrence equation and matching boundary conditions through digital computation and small signal behavior by linearizing it about the equilibrium state.

  15. Integrated S-band transmitter with on-chip DC-DC converter and control loop

    NARCIS (Netherlands)

    Brouzes, H.; Geurts, S.; Besselink, M.; Telli, A.; Hek, A.P. de; Bent, G. van der; Vliet, F.E. van

    2012-01-01

    A highly integrated high-power transmitter has been designed in a high breakdown GaAs MMIC technology. The transmitter includes, on top of an S-Band 10 W class-F HPA, a DC/DC converter and its associated gate driver, the full voltage regulation control loop, which provides a significant step for pha

  16. Regulation of a lightweight high efficiency capacitator diode voltage multiplier dc-dc converter

    Science.gov (United States)

    Harrigill, W. T., Jr.; Myers, I. T.

    1976-01-01

    A method for the regulation of a capacitor diode voltage multiplier dc-dc converter has been developed which has only minor penalties in weight and efficiency. An auxiliary inductor is used, which only handles a fraction of the total power, to control the output voltage through a pulse width modulation method in a buck boost circuit.

  17. Regulation of a lightweight high efficiency capacitor diode voltage multiplier dc-dc converter

    Science.gov (United States)

    Harrigill, W. T., Jr.; Myers, I. T.

    1976-01-01

    A method for the regulation of a capacitor diode voltage multiplier dc-dc converter has been developed which has only minor penalties in weight and efficiency. An auxiliary inductor is used, which only handles a fraction of the total power, to control the output voltage through a pulse width modulation method in a buck boost circuit.

  18. A high voltage ratio and low ripple interleaved DC-DC converter for fuel cell applications.

    Science.gov (United States)

    Chang, Long-Yi; Chao, Kuei-Hsiang; Chang, Tsang-Chih

    2012-01-01

    This paper proposes a high voltage ratio and low ripple interleaved boost DC-DC converter, which can be used to reduce the output voltage ripple. This converter transfers the low DC voltage of fuel cell to high DC voltage in DC link. The structure of the converter is parallel with two voltage-doubler boost converters by interleaving their output voltages to reduce the voltage ripple ratio. Besides, it can lower the current stress for the switches and inductors in the system. First, the PSIM software was used to establish a proton exchange membrane fuel cell and a converter circuit model. The simulated and measured results of the fuel cell output characteristic curve are made to verify the correctness of the established simulation model. In addition, some experimental results are made to validate the effectiveness in improving output voltage ripple of the proposed high voltage ratio interleaved boost DC-DC converters.

  19. Reliability-Oriented Optimization for the LC Filter Design of a Buck DC-DC Converter

    DEFF Research Database (Denmark)

    Liu, Yi; Huang, Meng; Wang, Huai;

    2017-01-01

    Lifetime is an important performance factor in the reliable operation of power converters. However, the state-of-the-art LC filter design of a buck DC-DC converter is limited to the specifications of voltage and current ripples and constrains in power density and cost without reliability...... parameter sets. A 1 kW converter prototype is applied to verify the theoretical analysis and simulation....

  20. Design of a High Efficiency Boost DC-DC Converter

    Institute of Scientific and Technical Information of China (English)

    GAO Jing; YAO Suying; XU Jiangtao; SHI Zaifeng

    2009-01-01

    An accurate circuit of PWM/PFM mode converting and a circuit of auto-adaptively adjusting dimension of power transistor are described. The duty cycle of the signal when the control mode converts can be gained accu-rately by using ratios of currents and capacitances, and an optimal dimension of power transistor is derived with different loads. The converter is designed by 0.35 μm standard CMOS technology. Simulation results indicate that the converter starts work at 0.8 V input voltage. Combined with synchronized rectification, the transfer efficiency is higher than 90% with full load range, and achieves 97.5% at rating output.

  1. Analysis of the coupling behavior of PEM fuel cells and DC-DC converters

    Energy Technology Data Exchange (ETDEWEB)

    Groetsch, M.; Mangold, M.; Kienle, A. [Max Planck Institute for Dynamics of Complex Technical Systems, Process Synthesis and Process Dynamics Group, Sandtorstrasse 1, 39106 Magdeburg (Germany); Kienle, A. [Otto-von-Guericke-Universitaet Magdeburg, Lehrstuhl fuer Automatisierungstechnik / Modellbildung, Universitaetsplatz 2, 39106 Magdeburg (Germany)

    2009-07-01

    The connection between PEM fuel cells and common DC-DC converters is examined. The analysis is model-based and done for boost, buck and buck-boost converters. In a first step, the effect of the converter ripples upon the PEM fuel cell is shown. They introduce oscillations in the fuel cell. Their appearance is explained, discussed and possibilities for their suppression are given. After that, the overall behaviors of the coupled fuel cell-converter systems are analyzed. It is shown, that neither stationary multiplicities nor oscillations can be introduced by the couplings and therefore separate control approaches for both the PEMFC and the DC-DC converters are applicable. (author)

  2. Analysis of the Coupling Behavior of PEM Fuel Cells and DC-DC Converters

    Directory of Open Access Journals (Sweden)

    Achim Kienle

    2009-03-01

    Full Text Available The connection between PEM fuel cells and common DC-DC converters is examined. The analysis is model-based and done for boost, buck and buck-boost converters. In a first step, the effect of the converter ripples upon the PEM fuel cell is shown. They introduce oscillations in the fuel cell. Their appearance is explained, discussed and possibilities for their suppression are given. After that, the overall behaviors of the coupled fuel cell-converter systems are analyzed. It is shown, that neither stationary multiplicities nor oscillations can be introduced by the couplings and therefore separate control approaches for both the PEMFC and the DC-DC converters are applicable.

  3. Zero-voltage switching technique in dc/dc converters

    Science.gov (United States)

    Liu, Kwang-Hwa; Lee, Fred C. Y.

    1990-07-01

    A novel resonant switch operating under the principle of zero-voltage switching is presented. In contrast to the zero-current switching, this technique eliminates the switching loss and dv/dt noise due to the discharging of MOSFET junction capacitances and the reverse recovery of diodes, and enables the converters to operate at high frequencies. A dc analysis of the converter is carried out. The duality relationship between the zero-current switching technique and the zero-voltage switching technique is derived. The two techniques are compared using an example showing the duality between a current-mode quasi-resonant Buck converter and a voltage-mode quasi-resonant boost converter. A 5-MHz 50 V to 5 V flyback converter employing the zero-voltage switching technique has been implemented. The circuit contains the smallest number of components possible, and yet maintains high efficiency at high switching frequency.

  4. CIECA - Application to current programmed switching Dc-Dc converters

    Science.gov (United States)

    Chetty, P. R. K.

    1982-09-01

    The current injection equivalent circuit approach (CIECA) to modeling switching converter power stages is extended to model the current programmed converter power stages operating in fixed frequency, continuous inductor conduction mode. To demonstrate the method, modeling is carried out for the buck, boost, and buckboost converters to obtain small-signal linear equivalent circuit models which represent both input and output properties. The results of these analyses are presented in the form of linear equivalent circuit models as well as transfer functions. Though current programmed converters exhibit single-pole response, the addition of artificial ramp changes converters to exhibit well damped two-pole response. This has been investigated for the first time using CIECA. The results of these analyses are presented in the form of linear equivalent circuit models as well as transfer functions.

  5. Pulse-width modulated DC-DC power converters

    CERN Document Server

    Kazimierczuk, Marian K

    2008-01-01

    This book studies switch-mode power supplies (SMPS) in great detail. This type of converter changes an unregulated DC voltage into a high-frequency pulse-width modulated (PWM) voltage controlled by varying the duty cycle, then changes the PWM AC voltage to a regulated DC voltage at a high efficiency by rectification and filtering. Used to supply electronic circuits, this converter saves energy and space in the overall system. With concept-orientated explanations, this book offers state-of-the-art SMPS technology and promotes an understanding of the principle operations of PWM converters,

  6. A suitable model plant for control of the set fuel cell-DC/DC converter

    Energy Technology Data Exchange (ETDEWEB)

    Andujar, J.M.; Segura, F.; Vasallo, M.J. [Departamento de Ingenieria Electronica, Sistemas Informaticos y Automatica, E.P.S. La Rabida, Universidad de Huelva, Ctra. Huelva - Palos de la Frontera, S/N, 21819 La Rabida - Palos de la Frontera Huelva (Spain)

    2008-04-15

    In this work a state and transfer function model of the set made up of a proton exchange membrane (PEM) fuel cell and a DC/DC converter is developed. The set is modelled as a plant controlled by the converter duty cycle. In addition to allow setting the plant operating point at any point of its characteristic curve (two interesting points are maximum efficiency and maximum power points), this approach also allows the connection of the fuel cell to other energy generation and storage devices, given that, as they all usually share a single DC bus, a thorough control of the interconnected devices is required. First, the state and transfer function models of the fuel cell and the converter are obtained. Then, both models are related in order to achieve the fuel cell+DC/DC converter set (plant) model. The results of the theoretical developments are validated by simulation on a real fuel cell model. (author)

  7. Differential Mode EMI Filter Design for Isolated DC-DC Boost Converter

    DEFF Research Database (Denmark)

    Makda, Ishtiyaq Ahmed; Nymand, Morten

    2014-01-01

    is identified first. The DM noise model is then established and based on the harmonic analysis of the noise source voltage waveform, the complete Differential Mode EMI filter, including the filter resonance damping branch, is designed for a 3kW isolated dc-dc boost converter. The noise model and its theoretical......A Differential Mode EMI filter for a low input voltage high-current isolated dc-dc boost converter is designed and presented in this paper. The primary side Differential Mode noise voltage is low due to the high transformer turn ratio, however, the input current is very high and since the EMI limit...... also does not change for such converters, it requires greatly optimized design approach for the filter including the correct sizing of the filter components. A complete analytical filter design process is carried out such a way that the Differential Mode noise voltage source in the converter...

  8. Cryogenic Evaluation of an Advanced DC/DC Converter Module for Deep Space Applications

    Science.gov (United States)

    Elbuluk, Malik E.; Hammoud, Ahmad; Gerber, Scott S.; Patterson, Richard

    2003-01-01

    DC/DC converters are widely used in power management, conditioning, and control of space power systems. Deep space applications require electronics that withstand cryogenic temperature and meet a stringent radiation tolerance. In this work, the performance of an advanced, radiation-hardened (rad-hard) commercial DC/DC converter module was investigated at cryogenic temperatures. The converter was investigated in terms of its steady state and dynamic operations. The output voltage regulation, efficiency, terminal current ripple characteristics, and output voltage response to load changes were determined in the temperature range of 20 to -140 C. These parameters were obtained at various load levels and at different input voltages. The experimental procedures along with the results obtained on the investigated converter are presented and discussed.

  9. Chaos, bifurcation and intermittent phenomena in DC-DC converters under resonant parametric perturbation

    Science.gov (United States)

    Deivasundari, P.; Geetha, R.; Uma, G.; Murali, K.

    2013-07-01

    DC-DC converters act as a black box to study various bifurcations. In the present study, the influence of external periodic interference signal in the input of DC-DC voltage-mode controlled buck converter has been considered. It is found that the presence of sinusoidal or saw-tooth interference signal whose frequency is comparable with the switching frequency of the converter or its rational multiples manifests as remerging chaotic band attractors (or Feigenbaum trees) and intermittent chaos. However, the presence of sinusoidal interference signal having irrational frequency ratios with the switching frequency of the converter leads to quasi-periodic route to chaos. The study was carried out both theoretically and experimentally.

  10. High Voltage Coil Current Sensor for DC-DC Converters Employing DDCC

    Directory of Open Access Journals (Sweden)

    M. Drinovsky

    2015-12-01

    Full Text Available Current sensor is an integral part of every switching converter. It is used for over-current protection, regulation and in case of multiphase converters for balancing. A new high voltage current sensor for coil-based current sensing in DC-DC converters is presented. The sensor employs DDCC with high voltage input stage and gain trimming. The circuit has been simulated and implemented in 0.35 um BCD technology as part of a multiphase DC-DC converter where its function has been verified. The circuit is able to sustain common mode voltage on the input up to 40 V, it occupies 0.387*0.345 mm2 and consumes 3.2 mW typically.

  11. Reliability-Oriented Design of LC Filter in Buck DC-DC Converter

    DEFF Research Database (Denmark)

    Liu, Yi; Huang, Meng; Wang, Huai;

    2015-01-01

    State-of-the-art LC filter design of buck DC-DC converter is based on the specifications of voltage and current ripples and constrains in power density and cost. Since lifetime is an important performance factor in reliability critical applications, this digest proposes a method to optimize...... an optimized LC filter design to fulfill the required lifetime. The theoretical analysis and simulation study are presented which are verified by the experimental results from a buck converter prototype....

  12. A Three-Phase Bidirectional DC-DC Converter for Automotive Applications

    Energy Technology Data Exchange (ETDEWEB)

    Su, Gui-Jia [ORNL; Tang, Lixin [ORNL

    2008-01-01

    This paper presents a three-phase soft-switching, bidirectional dc-dc converter for high-power automotive applications. The converter employs dual three-phase active bridges and operates with a novel asymmetrical but fixed duty cycle for the top and bottom switches of each phase leg. Simulation and experimental data on a 6-kW prototype are included to verify the novel operating and power flow control principles.

  13. Incremental Conductance MPPT Algorithm for PV System Implemented Using DC-DC Buck and Boost Converter

    OpenAIRE

    2014-01-01

    The two basic topologies of switch mode DC-DC converters (Buck and Boost) are analyzed with a view of their use in PV (photovoltaic) systems, as the photovoltaic generator exhibits non-linear characteristics due to the change in environmental condition and load variation. As the efficiency of PV panels is low it becomes mandatory to extract maximum power from the PV panel at a given period of time. Several MPPT algorithms with different types of converters are being proposed f...

  14. SIMPLIFIED APPROACHES FOR CONTROLLING DC-DC POWER CONVERTERS

    Directory of Open Access Journals (Sweden)

    M. M. ABDEL AZIZ

    2012-02-01

    Full Text Available This paper represents the design procedures of different compensation schemes for voltage mode controlled (VMC dc–dc switching converters. Proportional integral derivative (PID controllers, Fuzzy logic controllers (FLC, parallel combination of PID and FLC, and FLC tuned by PI controller have been investigated. MATLAB software is used to depict the buck converter performance with each compensator type when it is electrically simulated, and analytically modeled using its equivalent transfer function (TF. The comparative study Resultsemphasize that FLC tuned by PI controller is superior to the other control strategies because of fast transient response, minimum steady state error and good disturbance rejection under various variations of the operating conditions. Hence, it achieves the most tightly output voltage regulation.

  15. Self-Stable Chaos Control of dc-dc Converter

    Institute of Scientific and Technical Information of China (English)

    LU Wei-Guo; ZHOU Luo-Wei; WU Jun-Ke

    2009-01-01

    A new concept related to self-stable chaos control is first put forward,and its theoretical basis and realization are presented from the frequency-domain perspective. With a new analogous-circuit realization of this control its applications in the voltage-mode Buck converter is discussed. The harmonic-balance method is applied to determine the control range of the control parameter.The experiment results given in the last part confirm the validity of the proposed control method.

  16. Ultra-high Efficiency DC-DC Converter using GaN Devices

    DEFF Research Database (Denmark)

    Ramachandran, Rakesh

    2016-01-01

    with the PCB layout and the magnetics. This thesis mainly covers the design and implementation of various high efficiency isolated dcdc converters in the range of 1 to 2.5 kW of output power. Both hard-switched and soft-switched topologies in isolated dc-dc converters has been studied and realized......The demands for high efficiency dc-dc power converters are increasing day by day in various applications such as telecommunication, data-centers, electric vehicles and various renewable energy systems. Silicon (Si) has been used as the semiconductor material in majority of the power devices...... for many decades. However, the rate of improvement slowed as the silicon power materials asymptotically approached its theoretical bounds. Compared to Si, wideband gap materials such as Silicon Carbide (SiC) and Gallium Nitride (GaN) are promising semiconductors for power devices due to their superior...

  17. 5 kW DC/DC converter for hydrogen generation from photovoltaic sources

    Energy Technology Data Exchange (ETDEWEB)

    Garrigos, A.; Blanes, J.M.; Carrasco, J.A.; Lizan, J.L. [Area de Tecnologia Electronica, Universidad Miguel Hernandez de Elche, Avda. de la Universidad s/n, 03202 Elche, Alicante (Spain); Beneito, R. [AIJU, Avda. de la Industria 23, 03440 Ibi, Alicante (Spain); Molina, J.A. [Grupo SITEC, Calle Cadiz 38, Poligono Industrial L' Alfac III, 03440 Ibi, Alicante (Spain)

    2010-06-15

    This paper covers the design of a DC-DC power converter aimed for hydrogen production from photovoltaic sources. Power conditioning for such application is usually driven by different constraints: high step-down conversion ratio is required if the input voltage of such equipment has to be compatible with photovoltaic sources that are connected to grid-connected inverters; galvanic isolation; high efficiency and low mass. Taking into account those factors, this work proposes a push-pull DC/DC converter for power levels up to 5 kW. The operation and features of the converter are presented and analyzed. Design guidelines are suggested and experimental validation is also given. (author)

  18. SUBCONTRACT REPORT: DC-DC Converter for Fuel Cell and Hybrid Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Marlino, Laura D [ORNL; Zhu, Lizhi [Ballard Power Systems/Siemens VDO

    2007-07-01

    The goal of this project is to develop and fabricate a 5kW dc-dc converter with a baseline 14V output capability for fuel cell and hybrid vehicles. The major objectives for this dc-dc converter technology are to meet: Higher efficiency (92%); High coolant temperature,e capability (105 C); High reliability (15 Years/150,000miles); Smaller volume (5L); Lower weight (6kg); and Lower cost ($75/kW). The key technical challenge for these converters is the 105 C coolant temperatures. The power switches and magnetics must be designed to sustain these operating temperatures reliably, without a large cost/mass/volume penalty.

  19. Development of DC-DC converters for the upgrade of the CMS pixel detector

    Energy Technology Data Exchange (ETDEWEB)

    Feld, Lutz; Karpinski, Waclaw; Klein, Katja; Sammet, Jan; Wlochal, Michael [RWTH Aachen University (Germany)

    2012-07-01

    Around 2017, the pixel detector of the CMS experiment at LHC will be upgraded. The amount of current that has to be provided to the front-end electronics is expected to increase by a factor of two. Since the space available for cables is limited, this would imply unacceptable power losses in the available supply cables. Therefore it is foreseen to place DC-DC converters close to the front-end electronics, allowing to provide the power at higher voltages and thereby to facilitate the supply of the required currents with the present cable plant. The talk introduces the foreseen powering scheme of the pixel upgrade and summarizes the results of system test measurements with CMS pixel sensor modules, radiation tolerant DC-DC converters and the full power supply chain of the pixel detector. In addition, measurements of the converter efficiency and performance before, after and during thermal cycling are presented.

  20. Novel Full-bridge ZVS DC-DC Converter with an Clamp Diodes

    Science.gov (United States)

    Guangqun, Nan; Xue, Hu

    The two arms of this converter all work at zero-voltage switching condition, that bring many advantages, such as little loss of power, simple control, etc. But these also exists some problems, such as parasitic oscillation on the output rectifier diodes. A novel full-bridge ZVS PWM DC-DC converter which adopts two clamping diodes in the first side of the transformer is proposed to reduce the parasitic oscillation in this paper. In this paper, It heavily analyzes the realization process of their soft-switching and the reason of related issues and solution, we establishes simulation model and simulates using orCAD. Finally,a 5 kW ZVS PWM DC-DC converter Prototype in that TMS320F2812 is the core controlled chip has been set up, and the experiments showed us the validation of the correlative theory.

  1. Embedded Controlled Isolated Bidirectional Full-Bridge DC-DC Converter with Flyback Snubber

    Directory of Open Access Journals (Sweden)

    D. Kirubakaran

    2012-01-01

    Full Text Available An isolated bidirectional full-bridge DC-DC converter with flyback snubber for supplying a resistive load is simulated and experimentally verified. The DC-DC converter for high conversion ratio, high output power, and soft start-up capability is presented in this paper. The circuit consists of a capacitor, a diode, and a flyback converter. These components help to clamp the voltage spikes caused by the current difference between the current fed inductor and leakage inductance of the isolation transformer. The switches are operated by soft-switching technology. The suppression of inrush current which is usually found in the boost mode start-up transition is presented here. The simulated and experimental results for output voltage, output current, and power for both buck and boost modes are presented.

  2. Voltage Tracking of a DC-DC Flyback Converter Using Neural Network Control

    Directory of Open Access Journals (Sweden)

    Wahyu Mulyo Utomo

    2012-01-01

    Full Text Available This paper proposes a neural network control scheme of a DC-DC Flyback converter that will step up a 12V DC and applied it on brushless DC motor with 12 and 24V dc. In this technique, a back propagation learning algorithm is derived. The controller is designed to track the output voltage of the DC-DC converter and to improve performance of the Flyback converter during transient operations. Furthermore, to investigate the effectiveness of the proposed controller, some operations such as starting-up and reference voltage variations are verified. The numerical simulation results show that the proposed controller has a better performance compare to the conventional PI-Controller method.

  3. A highly efficient PV system using a series connection of DC-DC converter output with a photovoltaic panel

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ho-sung [Department of Electrical Engineering, Pusan National University, Jangjeon-dong, Geumjeong-gu, Busan 609-735 (Korea); New and Renewable Energy System Research Center, Korea Electro-technology Research Institute, 28-1, Sungju-dong Changwon-si, Kyungsannam-do, 641-120 (Korea); Kim, Jong-Hyun; Min, Byung-Duk; Yoo, Dong-Wook [New and Renewable Energy System Research Center, Korea Electro-technology Research Institute, 28-1, Sungju-dong Changwon-si, Kyungsannam-do, 641-120 (Korea); Kim, Hee-Je [Department of Electrical Engineering, Pusan National University, Jangjeon-dong, Geumjeong-gu, Busan 609-735 (Korea)

    2009-11-15

    A photovoltaic (PV) power conditioning system (PCS) must have high conversion efficiency and low cost. Generally, a PV PCS uses either a single string converter or a multilevel module integrated converter (MIC). Each of these approaches has both advantages and disadvantages. For a high conversion efficiency and low cost PV module, a series connection of a module integrated DC-DC converter output with a photovoltaic panel was proposed. The output voltage of the PV panel is connected to the output capacitor of the fly-back converter. Thus, the converter output voltage is added to the output voltage of the PV panel. The isolated DC-DC converter generates only the difference voltage between the PV panel voltage and the required total output voltage. This method reduces the power level of the DC-DC converter and enhances energy conversion efficiency compared with a conventional DC-DC converter. (author)

  4. Modeling and Analysis of Transformerless High Gain Buck-boost DC-DC Converters

    Directory of Open Access Journals (Sweden)

    Vu Tran

    2014-12-01

    Full Text Available This paper proposes a transfomerless switched capacitor buck boost converter model, which provides higher voltage gain and higher efficiency when compared to the conventional buck boost converter. The averaged model based on state-space description is analyzed in the paper. The simulation results are presented to confirm the capability of the converter to generate high voltage ratios. The comparison between the proposed model and the traditional model is also provided to reveal the improvement. The proposed converter is suitable for for a wide application which requires high step-up DC-DC converters such as DC micro-grids and solar electrical energy.

  5. A DC-DC Converter Efficiency Model for System Level Analysis in Ultra Low Power Applications

    Directory of Open Access Journals (Sweden)

    Benton H. Calhoun

    2013-06-01

    Full Text Available This paper presents a model of inductor based DC-DC converters that can be used to study the impact of power management techniques such as dynamic voltage and frequency scaling (DVFS. System level power models of low power systems on chip (SoCs and power management strategies cannot be correctly established without accounting for the associated overhead related to the DC-DC converters that provide regulated power to the system. The proposed model accurately predicts the efficiency of inductor based DC-DC converters with varying topologies and control schemes across a range of output voltage and current loads. It also accounts for the energy and timing overhead associated with the change in the operating condition of the regulator. Since modern SoCs employ power management techniques that vary the voltage and current loads seen by the converter, accurate modeling of the impact on the converter efficiency becomes critical. We use this model to compute the overall cost of two power distribution strategies for a SoC with multiple voltage islands. The proposed model helps us to obtain the energy benefits of a power management technique and can also be used as a basis for comparison between power management techniques or as a tool for design space exploration early in a SoC design cycle.

  6. Parallel input parallel output high voltage bi-directional converters for driving dielectric electro active polymer actuators

    DEFF Research Database (Denmark)

    Thummala, Prasanth; Zhang, Zhe; Andersen, Michael A. E.;

    2014-01-01

    is to design and implement driving circuits for the DEAP actuators for their use in various applications. This paper presents implementation of parallel input, parallel output, high voltage (~2.5 kV) bi-directional DC-DC converters for driving the DEAP actuators. The topology is a bidirectional flyback DC......-DC converter incorporating commercially available high voltage MOSFETs (4 kV) and high voltage diodes (5 kV). Although the average current of the aforementioned devices is limited to 300 mA and 150 mA, respectively, connecting the outputs of multiple converters in parallel can provide a scalable design....... This enables operating the DEAP actuators in various static and dynamic applications e.g. positioning, vibration generation or damping, and pumps. The proposed idea is experimentally verified by connecting three high voltage converters in parallel to operate a single DEAP actuator. The experimental results...

  7. Novel family of quasi-Z-source DC/DC converters derived from current-fed push-pull converters

    DEFF Research Database (Denmark)

    Chub, Andrii; Husev, Oleksandr; Vinnikov, Dmitri

    2014-01-01

    This paper is devoted to the step-up quasi-Z-source dc/dc push-pull converter family. The topologies in the family are derived from the isolated boost converter family by replacing input inductors with the quasi-Z-source network. Two new topologies are proposed, analyzed and compared. Theoretical...

  8. Integrated Three-Port DC-DC Converter for Photovoltaic (PV) Battery Stand-alone Systems

    DEFF Research Database (Denmark)

    Ouyang, Ziwei; Andersen, Michael A. E.

    2016-01-01

    different single-input single-output (SISO) dc/dc converters would have been used. To reduce the cost and improve the power density of the system, an integrated three-port isolated dc/dc converter is proposed in this paper. It can realize all functions of the energy delivery due to the fluctuation nature......Several power sources such as PV solar arrays and battery are often used to manage the power flow for a photovoltaic (PV) based stand-alone power system due to the fluctuation nature of solar energy resource, and deliver a continuous power to the users in an appropriate form. Traditionally, three...... for PV and battery stand-alone system....

  9. Optimization of Shielded PCB Air-Core Toroids for High-Efficiency DC-DC Converters

    CERN Document Server

    Orlandi, S; Buso, S; Michelis, S; Fuentes, C A; Kayal, M; Faccio, F; Spiazzi, G

    2011-01-01

    The paper describes the design of optimized printed circuit board (PCB) air-core toroids for high-frequency dc-dc converters with strict requirements in terms of volume and noise. The effect of several design parameters on the overall inductor volume, on dc and ac winding resistance, and on the radiated noise will be investigated. PCB toroids are compared to standard air-core solenoids and other state-of-the-art air-core toroids both theoretically and experimentally: at first, using ANSOFT Maxwell and ANSOFT Q3D simulation tools, and subsequently, with laboratory measurements (irradiated noise, efficiency, and frequency response) on several prototypes. These very flexible and rather easy to manufacture inductors appear very attractive for compact high-frequency dc-dc converters where high efficiency, low volume, and low noise are of primary concern.

  10. Switched capacitor DC-DC converter ASICs for the upgraded LHC trackers

    Energy Technology Data Exchange (ETDEWEB)

    Bochenek, M; Faccio, F; Michelis, S [CERN, CH-1211 Geneve 23 (Switzerland); Dabrowski, W, E-mail: Michal.Bochenek@cern.ch [AGH University of Science and Technology, Faculty of Physics and Applied Computer Science, Al. Mickiewicza 30 30-059 Krakow (Poland)

    2010-12-15

    The High Luminosity Upgrade of the ATLAS Inner Tracker puts demanding requirements on the powering system of the silicon strip detector modules due to 10-fold increase of the channel count compared to the existing SemiConductor Tracker. Therefore, new solutions for the powering scheme must be elaborated. Currently two possible approaches, the serial powering and the parallel powering scheme using the DC-DC conversion technique, are under development. This paper describes two switched capacitor DC-DC converters designed in a 130 nm technology. For the optimized step-down converter, foreseen for the parallel powering scheme, power efficiency of 97% has been achieved, while for the charge pump, designed for the serial powering scheme, power efficiency of 85% has been achieved.

  11. Switched capacitor DC-DC converter ASICs for the upgraded LHC trackers

    CERN Document Server

    Bochenek, M; Faccio, F; Michelis, S

    2010-01-01

    The High Luminosity Upgrade of the ATLAS Inner Tracker puts demanding requirements on the powering system of the silicon strip detector modules due to 10-fold increase of the channel count compared to the existing SemiConductor Tracker. Therefore, new solutions for the powering scheme must be elaborated. Currently two possible approaches, the serial powering and the parallel powering scheme using the DC-DC conversion technique, are under development. This paper describes two switched capacitor DC-DC converters designed in a 130 nm technology. For the optimized step-down converter, foreseen for the parallel powering scheme, power efficiency of 97% has been achieved, while for the charge pump, designed for the serial powering scheme, power efficiency of 85% has been achieved

  12. A Nonlinear Digital Control Solution for a DC/DC Power Converter

    Science.gov (United States)

    Zhu, Minshao

    2002-01-01

    A digital Nonlinear Proportional-Integral-Derivative (NPID) control algorithm was proposed to control a 1-kW, PWM, DC/DC, switching power converter. The NPID methodology is introduced and a practical hardware control solution is obtained. The design of the controller was completed using Matlab (trademark) Simulink, while the hardware-in-the-loop testing was performed using both the dSPACE (trademark) rapid prototyping system, and a stand-alone Texas Instruments (trademark) Digital Signal Processor (DSP)-based system. The final Nonlinear digital control algorithm was implemented and tested using the ED408043-1 Westinghouse DC-DC switching power converter. The NPID test results are discussed and compared to the results of a standard Proportional-Integral (PI) controller.

  13. A Novel Single Switch Transformerless Quadratic DC/DC Buck-Boost Converter

    DEFF Research Database (Denmark)

    Mostaan, Ali; A. Gorji, Saman; N. Soltani, Mohsen

    2017-01-01

    A novel quadratic buck-boost DC/DC converter is presented in this study. The proposed converter utilizes only one active switch and can step-up/down the input voltage, while the existing single switch quadratic buck/boost converters can only work in step-up or step-down mode. First, the proposed ...... converter is analyzed in steady-state. Then, its performance is validated using simulations in MATLAB/SIMULINK software. Finally, an experimental prototype is built for further verification....

  14. DC-DC Converter Topology Assessment for Large Scale Distributed Photovoltaic Plant Architectures

    Energy Technology Data Exchange (ETDEWEB)

    Agamy, Mohammed S; Harfman-Todorovic, Maja; Elasser, Ahmed; Sabate, Juan A; Steigerwald, Robert L; Jiang, Yan; Essakiappan, Somasundaram

    2011-07-01

    Distributed photovoltaic (PV) plant architectures are emerging as a replacement for the classical central inverter based systems. However, power converters of smaller ratings may have a negative impact on system efficiency, reliability and cost. Therefore, it is necessary to design converters with very high efficiency and simpler topologies in order not to offset the benefits gained by using distributed PV systems. In this paper an evaluation of the selection criteria for dc-dc converters for distributed PV systems is performed; this evaluation includes efficiency, simplicity of design, reliability and cost. Based on this evaluation, recommendations can be made as to which class of converters is best fit for this application.

  15. A High Power Density DC-DC Converter for Distributed PV Architectures

    Energy Technology Data Exchange (ETDEWEB)

    Agamy, Mohammed S; Chi, Song; Elasser, Ahmed; Harfman-Todorovic, Maja; Jiang, Yan; Mueller, Frank; Tao, Fengfeng

    2012-06-01

    In order to maximize solar energy harvesting capabilities, power converters have to be designed for high efficiency and good MPPT and voltage/current performance. When many converters are used in distributed systems, power density also becomes an important factor as it allows for simpler system integration. In this paper a high power density string dc-dc converter suitable for distributed medium to large scale PV installation is presented. A simple partial power processing topology, implemented with all silicon carbide devices provides high efficiency as well as high power density. A 3.5kW, 100kHz converter is designed and tested to verify the proposed methods.

  16. Simulating and Testing a DC-DC Half-Bridge SLR Converter

    Science.gov (United States)

    2013-06-01

    future pulse power demands with ship power, a large bank of capacitors or similar rapid discharge source is required. If capacitors are charged...Single Pulsed Avalanche Energy (j) I" Avalanche Current (i) E,, Repetilive Avalanche Energy (i) dv/dt Peak Diode Recovery dv/dt ® Po Total Power...SLR), battery charging, DC-DC, pulse power, power electronics, SLR converter 15. NUMBER OF PAGES 119 16. PRICE CODE 17. SECURITY CLASSIFICATION

  17. Impedance matching and DC-DC converter designs for tunable radio frequency based mobile telecommunication systems

    OpenAIRE

    Wong, Yan Chiew

    2014-01-01

    Tunability and adaptability for radio frequency (RF) front-ends are highly desirable because they not only enhance functionality and performance but also reduce the circuit size and cost. This thesis presents a number of novel design strategies in DC-DC converters, impedance networks and adaptive algorithms for tunable and adaptable RF based mobile telecommunication systems. Specifically, the studies are divided into three major directions: (a) high voltage switch controller ba...

  18. Informational model verification of ZVS Buck quasi-resonant DC-DC converter

    Science.gov (United States)

    Vakovsky, Dimiter; Hinov, Nikolay

    2016-12-01

    The aim of the paper is to create a polymorphic informational model of a ZVS Buck quasi-resonant DC-DC converter for the modeling purposes of the object. For the creation of the model is applied flexible open standards for setting, storing, publishing and exchange of data in distributed information environment. The created model is useful for creation of many and different by type variants with different configuration of the composing elements and different inner model of the examined object.

  19. Inductor based switching DC-DC converter for low voltage power distribution in SLHC

    CERN Document Server

    Michelis, S; Marchioro, A; Kayal, M; PH-EP

    2007-01-01

    In view of a power distribution scheme compatible with the requirements of the SLHC environment, we are evaluating the feasibility of on-board inductor-based DC-DC step-down conversion. Such converter should be an integrated circuit and capable of operating in harsh radiation environments and in the high magnetic field of the experiments. In this paper we present results concerning the choice of the technology, the search for the magnetic components and the calculations of the expected efficiency.

  20. System Tests with DC-DC Converters for the CMS Silicon Strip Tracker at SLHC

    CERN Document Server

    Klein, K; Karpinski, W; Merz, J; Sammet, J

    2008-01-01

    The delivery of power is considered to be one of the major challenges for the upgrade of the CMS silicon strip tracker for SLHC. The inevitable increase in granularity and complexity of the device is expected to result in a power consumption comparable or even higher than the power consumption of todays' strip tracker. However, the space available for cables will remain the same. In addition, a further increase of the tracker material budget due to cables and cooling is considered inacceptable, as the performance of the CMS detector must not be compromised for the upgrade. Novel powering schemes such as serial powering or usage of DC-DC converters have been proposed to solve the problem. To test the second option, substructures of the current CMS silicon strip tracker have been operated for the first time with off-the-shelf DC-DC buck converters as well as with first prototypes of custom-designed DC-DC converters. The tests are described and the results are discussed.

  1. Radiation effects in power converters: Design of a radiation hardened integrated switching DC/DC converter

    Science.gov (United States)

    Adell, Philippe

    . This design is the first radiation-hardened DC/DC power converter in this power range that integrates the switch, controller, and rectifier. The design has been fabricated, simulated and tested.

  2. Estimation of Bidirectional Buck/boost DC/DC Converters with Electric Double-Layer Capacitors for Energy Storage Systems

    Science.gov (United States)

    Funabiki, Shigeyuki; Yamamoto, Masayoshi

    Renewable energy such as wind force and solar light has collected the attention as alternative energy sources of fossil fuel. An energy storage system with an electric double-layer capacitor (EDLC), which balances the demand and supply power, is required in order to introduce the electric power generating system that utilizes renewable energy. Currently, the research and development of these energy storage systems are actively carried out. In the energy storage system with an EDLC, the DC/DC converter having the function of the bidirectional power flow and the buck/boost performance is essential as an interface and power control circuit. There are two types of the bidirectional buck/boost DC/DC converters. One type consists of two buck/boost DC/DC converters with one reactor. The other type consists of two sets of two-quadrant DC/DC converters with one reactor. This paper discusses the comparison of these types of DC/DC converters with bidirectional power flow and buck/boost performance. The two types of DC/DC converters are estimated for their application to the energy storage system with the EDLC. As the voltage endurance of the device is lower and the mean current is smaller in the latter type of converter despite of having twice the number of devices compared to the former, the latter type of converter has the advantage of a smaller reactor, i.e., core volume and loss, and lower loss in the converter.

  3. High voltage conversion ratio, switched C & L cells, step-down DC-DC converter

    DEFF Research Database (Denmark)

    Pelan, Ovidiu; Muntean, Nicolae; Cornea, Octavian;

    2013-01-01

    The paper presents a high voltage conversion ratio DC-DC step-down topology obtained from a classical buck converter associated with an input switched-capacitor cell and an output switched-inductor cell. Analytical descriptions, the voltage and current limits of the main components are synthesized...... in a comparative form, related to the classical buck structure, in order to emphasis the advantages of the proposed converter. Digital simulations and experimental results obtained with a built prototype are compared. From the first evaluation, the proposed converter is expected to be effectively used at input...

  4. A Novel PPFHB Bidirectional DC-DC Converter for Supercapacitor Application

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael Andreas E.

    2009-01-01

    This paper presents a novel bidirectional DC-DC converter for the supercapacitor application. In the proposed converter, push-pull forward with half bridge (PPFHB) voltage doubler structure is used to reduce the number of the power switches and get higher voltage gain. Based on phase......-shift modulation scheme, all the switches can realize zero-voltageswitching (ZVS) turn-on and bidirectional power flow can be controlled with phase-shift angle. The operating principles of the converter are described in detail, ZVS conditions are discussed, parameters are designed, and the experimental results...

  5. A New Approach for High Efficiency Buck-Boost DC/DC Converters Using Series Compensation

    Science.gov (United States)

    Itoh, Jun-Ichi; Fujii, Takashi

    This paper proposes a novel concept for non-isolated buck-boost DC/DC converter and control method. The proposed concept uses a series connection converter that only regulates the differential voltage between the input and output voltage. As a result, the power converter capacity is decreased. Moreover, the proposed circuit has advantages such as improved efficiency and losses reduction. The fundamental operation, control method, and design method of the proposed circuit are described in this paper. In addition, the validity of the proposed circuit is confirmed by carrying out simulations and experiments.

  6. Five-Level Active-Neutral-Point-Clamped DC/DC Converter

    DEFF Research Database (Denmark)

    Liu, Dong; Deng, Fujin; Chen, Zhe

    2016-01-01

    reliability. Furthermore, a capacitor voltage control strategy by alternating two operation modes of the proposed modulation strategy is proposed to balance the voltage of the flying capacitor, which ensures multi-level voltages producing. Finally, the performance of the proposed converter and control......Multi-level converters are getting more and more attentions because of their obvious merits such as lower voltage stress and harmonic, smaller size of output filters, and so on. In this paper, a five-level active-neutral-point-clamped (5L-ANPC) dc/dc converter is proposed for power transfer...

  7. Coupled Inductor Based High Step-Up DC-DC Converter for Multi Input PV System

    Directory of Open Access Journals (Sweden)

    G. Shiny Vikram

    2014-09-01

    Full Text Available With the shortage of the energy and ever increasing of the oil price, research on the renewable and green energy sources, especially the solar arrays and the fuel cells, becomes more and more important. How to achieve high step-up and high efficiency DC/DC converters is the major consideration in the renewable power applications due to the low voltage of PV arrays and fuel cells. In this paper a coupled inductor dc-dc converter for photovoltaic system is proposed. The circuit configuration of the proposed converter is very simple. Thus, the proposed converter has higher step-up and step-down voltage gains than the conventional bidirectional dc–dc boost/buck converter. Under same electric specifications for the proposed converter and the conventional bidirectional boost/buck converter, the average value of the switch current in the proposed converter is less than the conventional bidirectional boost/buck converter. The operating principles have been applied to multi input photovoltaic system and outputs have been observed.

  8. DC-DC buck converters for the CMS Tracker upgrade at SLHC

    Energy Technology Data Exchange (ETDEWEB)

    Feld, L; Jussen, R; Karpinski, W; Klein, K; Sammet, J, E-mail: Katja.Klein@cern.ch [1. Physikalisches Institut B, RWTH Aachen University, Sommerfeldstrasse 14, 52074 Aachen (Germany)

    2011-01-15

    The CMS experiment at the Large Hadron Collider (LHC) at CERN, Geneva, is planning major upgrades of its current pixel and strip detectors for the LHC luminosity upgrade, known as the SLHC. Due to the larger channel count and - in case of the strip tracker - increased functionality, the powering scheme adopted today, namely parallel powering of several detector modules, has to be abandoned. Instead, a powering scheme based on the DC-DC conversion technique is foreseen, which would lead to lower power losses in the supply cables, and would allow to reduce the material budget of cables and associated electronic boards in the sensitive detector volume. This paper deals with the development, characterisation and optimisation of DC-DC buck converter prototypes for the upgrades of the CMS pixel and strip detectors at the SLHC.

  9. A Feed-Forward Control Realizing Fast Response for Three-Branch Interleaved DC-DC Converter in DC Microgrid

    DEFF Research Database (Denmark)

    Wang, Haojie; Han, Minxiao; Yan, Wenli

    2016-01-01

    It is a common practice for storage batteries to be connected to DC microgrid buses through DC-DC converters for voltage support on islanded operation mode. A feed-forward control based dual-loop constant voltage PI control for three-branch interleaved DC-DC converters (TIDC) is proposed for stor......It is a common practice for storage batteries to be connected to DC microgrid buses through DC-DC converters for voltage support on islanded operation mode. A feed-forward control based dual-loop constant voltage PI control for three-branch interleaved DC-DC converters (TIDC) is proposed...... for storage batteries in DC microgrids. The working principle of TIDC is analyzed, and the factors influencing the response rate based on the dual-loop constant voltage control for TIDC are discussed, and then the method of feed-forward control for TIDC is studied to improve the response rate for load...

  10. High Efficiency Bi-Directional Converter Used For Renewable System

    Directory of Open Access Journals (Sweden)

    M. Desal Raja

    2014-02-01

    Full Text Available This paper presents an Isolated bi-directional converter for renewable system. Voltage stress and current stress was decreses in switches. Power flows in both side. The proposed converter three phase ac voltage to dc voltage, dc voltage to three phase a.c voltage and synchronous the two voltage source. Silicon carbide diodes and bi-directional switches Mosfet’s are used for decreases the switching loss. LC Series resonant converter connected to the high efficiency. This converter power conversion control by the output voltage information.

  11. Performance Analysis of Various DC-DC Converters with Optimum Controllers for PV Applications

    Directory of Open Access Journals (Sweden)

    R. Sankarganesh

    2014-08-01

    Full Text Available Alternative vehicles to Internal Combustion Engines (ICE, for instance the electric vehicle is becoming popular. Electric Vehicles (EV are pollution free and cost effective because the fossil fuel cost increases day by day. These factors make people passion for electric vehicles. Electrical energy demand necessitates charging of electric vehicles using renewable energy. Among the different renewable energy resources, Photovoltaic (PV cells are suitable for EV. The PV output power capacity is still low, so efforts continue to develop the PV converter and its controller, aiming for higher power-extracting efficiency. The PV system requires a proper DC-DC converter with optimum controller to deliver its maximum power. This study analyses the various DC-DC converters such as buck, boost, cuk and modified cuk converters to find the solution for maximum efficiency. In this study in addition to converters, various Maximum Power Point Tracking (MPPT methods, such as Perturb and Observe, Incremental Conductance along with a proposed algorithm called Brain Emotional Learning Based Intelligent Controller (BELBIC has been analyzed. The operation of the BELBIC is based on the emotion processing mechanism in the brain. This intelligent control is stimulated by the limbic system of the mammalian brain. The performance analysis of the converters and MPPT methods are simulated using MATLAB/SIMULINK. Furthermore, experimental results are presented in order to validate the modified cuk converter with proposed BELBIC algorithm.

  12. Transformerless DC-DC Converter Using Cockcroft-Walton Voltage Multiplier to Obtain High DC Voltage

    Directory of Open Access Journals (Sweden)

    Meghana G Naik,

    2014-11-01

    Full Text Available In the present scenario the use of transformer for high voltages in converter circuit reduces the overall operating efficiency due to leakage inductance and use of transformer also increases the operational cost. . Therefore the proposed system is implemented with transformer less DC-DC converter so as to obtain high DC voltage with the use of nine stage Cockcroft-Walton (CW voltage multiplier. The proposed converter operates in CCM (continuous conduction mode, so that the converter switch stress, the switching losses are reduced. The DC voltage at the input of the proposed model is low and is boosted up by boost inductor (Ls in DC-DC converter stage and performs inverter operation. The number of stages in CW-voltage multiplier circuit is applied with low input pulsating DC (AC Voltage voltage where it is getting converted to high DC output voltage. The proposed converter switches operates at two independent frequencies, modulating (fsm andalternating (fsc frequency. The fsm operates at higher frequency of the output while the fsc operates at lower frequency of the desired output voltage ripple and the output ripples can be adjusted by the switch Sc1 and Sc2. The regulation of the output voltage is achieved by controlling the Duty ratio.The simulation is carried over by the MATLABSIMULINK.

  13. Sliding-mode control of single input multiple output DC-DC converter

    Science.gov (United States)

    Zhang, Libo; Sun, Yihan; Luo, Tiejian; Wan, Qiyang

    2016-10-01

    Various voltage levels are required in the vehicle mounted power system. A conventional solution is to utilize an independent multiple output DC-DC converter whose cost is high and control scheme is complicated. In this paper, we design a novel SIMO DC-DC converter with sliding mode controller. The proposed converter can boost the voltage of a low-voltage input power source to a controllable high-voltage DC bus and middle-voltage output terminals, which endow the converter with characteristics of simple structure, low cost, and convenient control. In addition, the sliding mode control (SMC) technique applied in our converter can enhance the performances of a certain SIMO DC-DC converter topology. The high-voltage DC bus can be regarded as the main power source to the high-voltage facility of the vehicle mounted power system, and the middle-voltage output terminals can supply power to the low-voltage equipment on an automobile. In the respect of control algorithm, it is the first time to propose the SMC-PID (Proportion Integration Differentiation) control algorithm, in which the SMC algorithm is utilized and the PID control is attended to the conventional SMC algorithm. The PID control increases the dynamic ability of the SMC algorithm by establishing the corresponding SMC surface and introducing the attached integral of voltage error, which endow the sliding-control system with excellent dynamic performance. At last, we established the MATLAB/SIMULINK simulation model, tested performance of the system, and built the hardware prototype based on Digital Signal Processor (DSP). Results show that the sliding mode control is able to track a required trajectory, which has robustness against the uncertainties and disturbances.

  14. Research on transient hysteresis current control strategy of DC-DC converter

    Science.gov (United States)

    Zhang, Ting; Wang, Zu-liang; Zhao, Yu-kai

    2017-01-01

    In order to improve the dynamic performance of DC-DC converter, transient hysteresis current control strategy is proposed which is based on parallel computing and combinational logic. By making a comparison between the real-time inductor current and the threshold inductor current, the switch is controlled more accurately. Under the Matlab/Simulink environment, the process of the Buck-Boost converter was simulated. The simulation results show that the transient hysteresis current control strategy can effectively overcome the disadvantages when load changes or input voltage disturbance occurs, it posses high load regulation and short dynamic response time, and it verifies the feasibility of the proposed strategy.

  15. Analysis and Experimental Study of Proportional-Integral Sliding Mode Control for DC/DC Converter

    Institute of Scientific and Technical Information of China (English)

    ZHANG Li; QIU Shui-sheng

    2005-01-01

    DC/DC converter using the proportional-integral (PI) sliding mode control (SMC) scheme is investigated, including the selection of the switching surface, the proof of the reaching condition and the existence condition of sliding motion. The sliding regime and the local stability are given. The implementation of the PI SMC is simpler than other SMC schemes and the steady-state error is eliminated. A prototype based on Buck converter is built up. The experimental results show that the dynamic performance and robustness to the parameter variations and external disturbances are improved.

  16. Point-of-load switched-capacitor DC-DC converter for distributed power systems

    Science.gov (United States)

    Shunkov, V. E.; Kus, O. N.; Prokopyev, V. Y.; Butuzov, V. A.; Bocharov, Y. I.; Shunkov, V. E.

    2016-10-01

    Integrated circuit (IC) of point-of-load DC-DC converter is presented. It is intended mainly for use in distributed power systems as a stand-along IC or as an on-chip block of the system-on-chip. The converter is based on multiphase switched-capacitor architecture and implemented in commercially available, 180 nm bulk-CMOS process. The paper discusses features of output voltage control in the multiphase system over a wide range of input and output voltages and load currents as well as output noise reducing techniques. The results of the test samples evaluation are presented.

  17. Finite-time control of DC-DC buck converters via integral terminal sliding modes

    Science.gov (United States)

    Chiu, Chian-Song; Shen, Chih-Teng

    2012-05-01

    This article presents novel terminal sliding modes for finite-time output tracking control of DC-DC buck converters. Instead of using traditional singular terminal sliding mode, two integral terminal sliding modes are introduced for robust output voltage tracking of uncertain buck converters. Different from traditional sliding mode control (SMC), the proposed controller assures finite convergence time for the tracking error and integral tracking error. Furthermore, the singular problem in traditional terminal SMC is removed from this article. When considering worse modelling, adaptive integral terminal SMC is derived to guarantee finite-time convergence under more relaxed stability conditions. In addition, several experiments show better start-up performance and robustness.

  18. Ultra-Step-Up DC-DC Converter with Integrated Autotransformer and Coupled Inductor

    DEFF Research Database (Denmark)

    Siwakoti, Yam Prasad; Blaabjerg, Frede; Loh, Poh Chiang

    2016-01-01

    This paper introduces a new single-switch nonisolated dc-dc converter with very high voltage transfer ratio and reduced semiconductor voltage stress. The converter utilizes an integrated autotransformer and a coupled inductor on the same core to achieve a high step-up voltage gain without extreme...... to use a low voltage and low RDS-on MOSFET, which reduces the cost, and also the conduction and turn on losses of the switch. The principle of operation and theoretical analysis supported by key simulation and experimental waveforms are presented in details....

  19. SOFT-SWITCHED HIGH STEP-UP DC-DC CONVERTER WITH HIGH VOLTAGE GAIN

    Directory of Open Access Journals (Sweden)

    J.C. PAUL IMMANUEL

    2013-04-01

    Full Text Available This paper presents a new design of soft switched high step-up dc-dc converter with high voltage gain which is suitable for high power applications such as Uninterruptible Power System (UPS, Photo Voltaic system and hybrid electric vehicles. The emergence of this front-end converter is to improve the shape of active input current given to the system. This converter proposes Soft-Switching technique to achieve ZVS turn on of active switches and ZCS turn off of diodes using Lr - Cr resonance in the auxiliary circuit. Therefore reduces the switching losses. Comparatively the voltage conversion ratio of this converter is higher when compared with the ordinary boost converter. Hence the voltage gain of this converter is also higher. A simulation platform is created using MATLAB which illustrates the ZVS and ZCS operation of the switches and diodes. Open loop and closed loop controlled converter systems are modelled and simulated.

  20. Magnetically coupled high-gain Y-source isolated DC/DC converter

    DEFF Research Database (Denmark)

    Siwakoti, Yam P.; Loh, Poh Chiang; Blaabjerg, Frede;

    2014-01-01

    A new form of magnetically coupled DC/DC converter is proposed for medium power applications (250 W to 2 kW), requiring a high-voltage gain, short inductive charging time and galvanic isolation. The proposed converter can be realised using a unique Y-source impedance network and a two-switch push......-pull circuit with voltage-doubling rectification. The converter's voltage gain is presently not matched by any other converter operating at the same switch duty ratio. The converter also has more degrees of freedom in design for setting the desired gain than other converters, and hence can better meet...... the demands of many applications. The operating principles of the converter have been analysed mathematically, and are verified by both simulation and experiment....

  1. Direct switching control of DC-DC power electronic converters using hybrid system theory

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, J.; Lin, F. [Wayne State Univ., Detroit, MI (United States). Dept. of Electrical and Computer Engineering; Wang, C. [Wayne State Univ., Detroit, MI (United States). Dept. of Electrical and Computer Engineering; Wayne State Univ., Detroit, MI (United States). Div. of Engineering Technology

    2010-07-01

    A direct switching control (DSC) scheme for power electronics converters was described. The system was designed for use in both traditional and renewable energy applications as well as in electric drive vehicles. The proposed control scheme was based on a detailed hybrid system converter model that used model predictive control (MPC), piecewise affine (PWA) approximations and constrained optimal control methods. A DC-DC converter was modelled as a hybrid machine. Switching among different modes of the DC-DC converter were modelled as discrete events controlled by the hybrid controller. The modelling scheme was applied to a Buck converter. The DSC was used to control the switch of the power converter based on a hybrid machine model. Results of the study showed that the method can be used to regulate output voltage and inductor currents. The method also provides fast transient responses and effectively regulates both currents and voltage. The controller can be used to provide immediate responses to dynamic disturbances and output voltage fluctuations. 23 refs., 7 figs.

  2. The good routing of a non-insulated DC/DC converter; Bien router un convertisseur DC/DC non-isole

    Energy Technology Data Exchange (ETDEWEB)

    Lenoir, E.

    2001-03-01

    DC to DC converters are important sources of magnetic and electric fields with frequencies that can exceed 100 MHz. Thus, their positioning on a circuit board is of prime importance to minimize the magnetic and capacitive couplings with other parts and components of the circuit. This article summarizes the important rules to follow for a good routing of non-insulated switching DC/DC converters: taking the ohmic voltage drops into consideration, managing the MOSFET commutation, limiting the current loop disturbances, correct routing of power tracks. (J.S.)

  3. Practical Design Guidelines of qZSI Based Step-Up DC/DC Converter

    Science.gov (United States)

    Zakis, Janis; Vinnikov, Dmitri; Roasto, Indrek; Jalakas, Tanel

    2010-01-01

    This paper presents some design guidelines for a new voltage fed step-up DC/DC isolated converter. The most significant advantage of proposed converter is voltage buck-boost operation on single stage. The most promising application for proposed converter is in the field of distributed power generation e.g. fuel cells or photovoltaic. The most sensitive issues - such as power losses caused by high currents in the input side of converter and high transient overvoltages across the inverter bridge caused by stray inductances were discussed and solved. The proposals and recommendations to overcome these issues are given in the paper. The Selection and design guidelines of converter elements are proposed and explained. The prototype of proposed converter was built and experimentally tested. Some results are presented and evaluated.

  4. Light weight, high power, high voltage dc/dc converter technologies

    Science.gov (United States)

    Kraus, Robert; Myers, Ira; Baumann, Eric

    1990-01-01

    Power-conditioning weight reductions by orders of magnitude will be required to enable the megawatt-power-level space systems envisioned by the Strategic Defense Initiative, the Air Force, and NASA. An interagency program has been initiated to develop an 0.1-kg/kW dc/dc converter technology base for these future space applications. Three contractors are in the first phase of a competitive program to develop a megawatt dc/dc converter. Researchers at NASA Lewis Research Center are investigating innovative converter topology control. Three different converter subsystems based on square wave, resonant, and super-resonant topologies are being designed. The components required for the converter designs cover a wide array of technologies. Two different switches, one semiconductor and the other gas, are under development. Issues related to thermal management and material reliability for inductors, transformers, and capacitors are being investigated in order to maximize power density. A brief description of each of the concepts proposed to meet the goals of this program is presented.

  5. MPP-Tracking DC-DC converters in Photovoltaic applications. Implementation, modeling and analysis

    Energy Technology Data Exchange (ETDEWEB)

    Leppaeaho, J.

    2011-07-01

    This thesis provides a comprehensive study of switched-mode dc-dc converters in terms of dynamic characterization, implementation and operational constraints. The study concentrates on the maximum-power-point-tracking converters used in photovoltaic interfacing in order to maximize the power generation. The main objective is to emphasize the differences between the four basic conversion schemes and to analyze the dynamical characteristics of the current-fed converters. Harvesting of solar energy directly into electrical energy is known to be challenging due to the highly varying terminal characteristics of the energy harvesting unit, i.e., generally a photovoltaic generator. The environmental conditions as well as the load determine its characteristics. The operation point of PV generator has to be kept at its maximum-power point in order to maximize the harvested energy. The dc-dc switched-mode converters are conventionally used to interface the energy sources possessing constant-voltage behavior such as batteries or voltage buses but the same converters are also used as a basis for the maximum-power-point-tracking devices. It is observed, however, that such voltage-fed converters are not capable of interfacing a photovoltaic generator optimally because of its current-source nature. Therefore, an additional capacitor is usually added between the source and converter to enhance the constant-voltage properties of the source and to enable the input-voltage-based feedback control. It is known that the dual nature of PV generator enables the use of either input-voltage or input-current feedback control. It is observed, that the input-current control is prone to saturation of the controller and therefore, the input-voltage control is recommended to be used. The use of input-voltage control will, however, force the converter operate as a current-fed converter causing also significant changes to its static and dynamic properties as well as constraints related to the

  6. A New Zero Voltage Switching Buck-Boost Type DC-DC Converter

    Directory of Open Access Journals (Sweden)

    Majid Delshad

    2010-03-01

    Full Text Available In this paper, a new zero voltage switching isolated buck-boost DC-DC converter with active clamp circuit is proposed. The active clamp circuit in this converter not only absorbs voltage spikes across the main switch but also provides soft switching conditions for all switches. All switches are PWM controlled which simplifies the control implementation. One of the main advantages of this converter is the that it operating can operate at high power levels while soft switching conditions exist in both buck and boost modes of converter operation. Since this converter can operate over a wide input voltage range, it can be employed in power factor correction. The experimental results obtained from a 150W prototype circuit operating at 100KHz are presented to confirm the integrity of the proposed circuit.

  7. Comparison of control schemes for a fuel cell hybrid tramway integrating two dc/dc converters

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, L.M.; Garcia, P.; Garcia, C.A. [Department of Electrical Engineering, EPS Algeciras, University of Cadiz, Avda. Ramon Puyol, s/n, 11202 Algeciras (Cadiz) (Spain); Torreglosa, J.P.; Jurado, F. [Department of Electrical Engineering, EPS Linares, University of Jaen, C/Alfonso X, n 28. 23700 Linares (Jaen) (Spain)

    2010-06-15

    This paper describes a comparative study of two control schemes for the energy management system of a hybrid tramway powered by a Polymer Electrolyte Membrane (PEM) Fuel Cell (FC) and an Ni-MH battery. The hybrid system was designed for a real surface tramway of 400 kW. It is composed of a PEM FC system with a unidirectional dc/dc boost converter (FC converter) and a rechargeable Ni-MH battery with a bidirectional dc/dc converter (battery converter), both of which are coupled to a traction dc bus. The PEM FC and Ni-MH battery models were designed from commercially available components. The function of the two control architectures was to effectively distribute the power of the electrical sources. One of these control architectures was a state machine control strategy, based on eight states. The other was a cascade control strategy which was used to validate the results obtained. The simulation results for the real driving cycle of the tramway reflected the optimal performance of the control systems compared in this study. (author)

  8. Comparison of two different high performance mixed signal controllers for DC/DC converters

    DEFF Research Database (Denmark)

    Jakobsen, Lars Tønnes; Andersen, Michael Andreas E.

    2006-01-01

    This paper describes how mixed signal controllers combining a cheap microcontroller with a simple analogue circuit can offer high performance digital control for DC/DC converters. Mixed signal controllers have the same versatility and performance as DSP based controllers. It is important to have...... an engineer experienced in microcontroller programming write the software algorithms to achieve optimal performance. Two mixed signal controller designs based on the same 8-bit microcontroller are compared both theoretically and experimentally. A 16-bit PID compensator with a sampling frequency of 200 k......Hz implemented in the 16 MIPS, 8-bit ATTiny26 microcontroller is demonstrated....

  9. Analysis and Implementation of Dual-ZCS forward DC/DC Converter

    Institute of Scientific and Technical Information of China (English)

    WANG Jing-mei; LAN Zhong-wei; YU Zhong; WANG Hao-cai

    2005-01-01

    As the switching frequency in DC/DC converter increases, original 'hard-switch' working mode is not compatible. Another problem is the reliability, which is puzzled in single-ended forward, push-pull or bridge-like structures. In this paper, a new dual-ZCS (zero current switches) forward topology is proposed. The operating principle of soft-switch is analyzed, showing the relationship between voltage and current in time domain. Then how to calculate the key parameters of resonant network is . Finally, a prototype ZCS SMPS is implemented and tested. The results consisted with the analyzing results well, and illustrated the advantages of the proposed structure.

  10. Four Quadrants Integrated Transformers for Dual-input Isolated DC-DC Converters

    DEFF Research Database (Denmark)

    Ouyang, Ziwei; Zhang, Zhe; Andersen, Michael A. E.;

    2012-01-01

    A common limitation of power coupling effect in some known multiple-input dc-dc converters has been addressed in many literatures. In order to overcome this limitation, a new concept for decoupling the primary windings in the integrated multiple-winding transformers based on 3-dimensional (3D...... perpendicular primary windings, a name of “four quadrants integrated transformers” (FQIT) is therefore given to the proposed construction. Since the two primary windings are uncoupled, the FQIT allows the two input power stages to transfer the energy into the output load simultaneously or at any...

  11. A Super Performance Bandgap Voltage Reference with Adjustable Output for DC-DC Converter

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    This paper presents a super performance bandgap voltage reference for DC-DC converter with adjustable output. It generates a wide range of voltage reference ranging from sub- 1V to 1.221 7 V and has a low temperature coefficient of 2.3 × 10 - 5/K over the temperature variation using the current feedback and resistive subdivision. In addition, the power supply rejection ration of the proposed bandgap voltage reference is 78 dB. When supply voltage varies from 2.5 V to 6 V, output VREF is 1.221 685 ± 0.055 mV.

  12. Soft-start mechanism with coefficients Ki optimization for DC-DC power converters

    Science.gov (United States)

    Wang, Qian; Hu, Jiajun; Chen, Houpeng; Li, Xi; Fan, Xi; Miao, Jie; Song, Zhitang

    2016-10-01

    This paper presents a fully digital-control soft start mechanism with coefficients Ki optimization for DC-DC power converters. During the soft start phase, a ladder reference voltage steps up gradually to make inductor current ramp up smoothly and overshoot voltage is minimized with the proposed coefficients Ki distribution. Simulation results show that massive inductor current can be well avoided during the soft start process with the proposed soft start mechanism, which only occupies a chip area of 300um×120um.

  13. Non-Smooth Bifurcation and Chaos in a DC-DC Buck Converter

    Institute of Scientific and Technical Information of China (English)

    QIN Zhi-Ying; LU Qi-Shao

    2007-01-01

    A direct-current-dorect-current (DC-DC)buck converter with integrated load current feedback is studied with three kinds of Poicaré maps.The external corner-collision bifurcation occurs when the crossing number per period varies,and the internal corner-collision bifurcations occur along with period-doubling and period-tripling bifurcations in this model.The multi-band chaos roots in external corner-collision bifurcation and often grows into l-band chaos.A new kind of chaotic sliding orbits,which is more complex for non-smooth systems,is also found in this model.

  14. Hybrid Non-Isolated and Non Inverting Nx Interleaved DC-DC Multilevel Boost Converter for Renewable Energy Applications

    DEFF Research Database (Denmark)

    Bhaskar, Mahajan Sagar; Kulkarni, Rishi M.; Padmanaban, Sanjeevi Kumar;

    2016-01-01

    In this paper hybrid non isolated/ non inverting Nx interleaved DC-DC multilevel Boost Converter for renewable energy applications is presented. The presented hybrid topology is derived from the conventional interleaved converter and the Nx Multilevel boost converter. In renewable energy...... applications, generated energy cannot be directly used at application end. In most of the cases it needs to be stepped up with DC-DC converter at operating voltage levels as per the requirement of the application. Though conventional boost converter can theoretically be used for this purpose, but obtaining....... The advantages of presenting topology of DC-DC converter are high voltage conversion, reduce ripple, low voltage stress, non inverting without utilizing the high duty and transformer. The main advantage of presented topology is more number of levels can be increased by adding capacitor and diode circuitry...

  15. High Current Planar Transformer for Very High Efficiency Isolated Boost DC-DC Converters

    DEFF Research Database (Denmark)

    Pittini, Riccardo; Zhang, Zhe; Andersen, Michael A. E.

    2014-01-01

    This paper presents a design and optimization of a high current planar transformer for very high efficiency dc-dc isolated boost converters. The analysis considers different winding arrangements, including very high copper thickness windings. The analysis is focused on the winding ac-resistance a......This paper presents a design and optimization of a high current planar transformer for very high efficiency dc-dc isolated boost converters. The analysis considers different winding arrangements, including very high copper thickness windings. The analysis is focused on the winding ac......-resistance and transformer leakage inductance. Design and optimization procedures are validated based on an experimental prototype of a 6 kW dcdc isolated full bridge boost converter developed on fully planar magnetics. The prototype is rated at 30-80 V 0-80 A on the low voltage side and 700-800 V on the high voltage side...... with a peak efficiency of 97.8% at 80 V 3.5 kW. Results highlights that thick copper windings can provide good performance at low switching frequencies due to the high transformer filling factor. PCB windings can also provide very high efficiency if stacked in parallel utilizing the transformer winding window...

  16. Optimization with System Damping Restoration for Droop Controlled DC-DC Converters

    DEFF Research Database (Denmark)

    Meng, Lexuan; Dragicevic, Tomislav; Guerrero, Josep M.;

    2013-01-01

    the efficiency of the conversion system, this paper implements tertiary level optimization control on the basis of hierarchical control. As the efficiency of each converter changes with output power, VRs are set as decision variables for adjusting power sharing proportion among converters. Genetic algorithm...... restoration (SDSR) is implemented to readjust the optimization results so as to ensure system stability. Simulation results are shown to demonstrate the improvement of system efficiency and effectiveness of the method.......The parallel operation of dc-dc converters is widely used in distribution systems and uninterruptable power supply systems. Droop control along with virtual resistance (VR) is considered a simple and reliable method for achieving wireless power sharing among converters. In order to enhance...

  17. Low Temperature Performance of High Power Density DC/DC Converter Modules

    Science.gov (United States)

    Elbuluk, Malik E.; Hammond, Ahmad; Gerber, Scott; Patterson, Richard L.; Overton, Eric

    2001-01-01

    In this paper, two second-generation high power density DC/DC converter modules have been evaluated at low operating temperatures. The power rating of one converter (Module 1) was specified at 150 W with an input voltage range of 36 to 75 V and output voltage of 12 V. The other converter (Module 2) was specified at 100 W with the same input voltage range and an output voltage of 3.3 V. The converter modules were evaluated in terms of their performance as a function of operating temperature in the range of 25 to -140 C. The experimental procedures along with the experimental data obtained are presented and discussed in this paper.

  18. Performance of a spacecraft DC-DC converter breadboard modified for low temperature operation

    Science.gov (United States)

    Gerber, Scott S.; Stell, Chris; Patterson, Richard; Ray, Biswajit

    1996-01-01

    A 1OW 3OV/5.OV push-pull dc-dc converter breadboard, designed by the Jet Propulsion Laboratory (JPL) with a +50 C to +5 C operating range for the Cassini space probe, was characterized for lower operating temperatures. The breadboard converter which failed to operate for temperatures below -125 C was then modified to operate at temperatures approaching that of liquid nitrogen (LN2). Associated with this low operating temperature range (greater than -196 C) was a variety of performance problems such as significant change in output voltage, converter switching instability, and failure to restart at temperatures below -154 C. An investigation into these problems yielded additional modifications to the converter which improved low temperature performance even further.

  19. A low noise high efficiency buck DC-DC converter with sigma-delta modulation

    Energy Technology Data Exchange (ETDEWEB)

    Cai Shujiang; Pi Changming; Yan Wei; Li Wenhong, E-mail: wenhongli@fudan.edu.cn [State Key Laboratory of ASIC and Systems, Fudan University, Shanghai 201203 (China)

    2011-07-15

    Some research efforts to improve the efficiency and noise performance of buck DC-DC converters are explored. A carefully designed power MOSFET driver, including a dead time controller, discontinuous current mode (DCM) controller and gate width controller, is proposed to improve efficiency. Instead of PWM modulation, sigma-delta modulation is introduced into the feedback loop of the converter to move out the clock-referred harmonic spike. The proposed converter has been designed and fabricated by a 0.35 {mu}m CMOS process. Measured results show that the peak efficiency of the converter can reach 93% and sigma-delta modulation suppresses the harmonic spike by 30 dB over PWM modulation. (semiconductor integrated circuits)

  20. Analysis of Discontinuity Induced Bifurcations in a Dual Input DC-DC Converter

    Science.gov (United States)

    Giaouris, Damian; Banerjee, Soumitro; Mandal, Kuntal; Al-Hindawi, Mohammed M.; Abusorrah, Abdullah; Al-Turki, Yusuf; El Aroudi, Abdelali

    DC-DC power converters with multiple inputs and a single output are used in numerous applications where multiple sources, e.g. two or more renewable energy sources and/or a battery, feed a single load. In this work, a classical boost converter topology with two input branches connected to two different sources is chosen, with each branch independently being controlled by a separate peak current mode controller. We demonstrate for the first time that even though this converter is similar to other well known topologies that have been studied before, it exhibits many complex nonlinear behaviors that are not found in any other standard PWM controlled power converter. The system undergoes period incrementing cascade as a parameter is varied, with discontinuous hard transitions between consecutive periodicities. We show that the system can be described by a discontinuous map, which explains the observed bifurcation phenomena. The results have been experimentally validated.

  1. Predictive Trailing-Edge Modulation Average Current Control in DC-DC Converters

    Directory of Open Access Journals (Sweden)

    LASCU, D.

    2013-11-01

    Full Text Available The paper investigates predictive digital average current control (PDACC in dc/dc converters using trailing-edge modulation (TEM. The study is focused on the recurrence duty cycle equation and then stability analysis is performed. It is demonstrated that average current control using trailing-edge modulation is stable on the whole range of the duty cycle and thus design problems are highly reduced. The analysis is carried out in a general manner, independent of converter topology and therefore the results can then be easily applied for a certain converter (buck, boost, buck-boost, etc.. The theoretical considerations are confirmed for a boost converter first using the MATLAB program based on state-space equations and finally with the CASPOC circuit simulation package.

  2. Incremental Conductance MPPT Algorithm for PV System Implemented Using DC-DC Buck and Boost Converter

    Directory of Open Access Journals (Sweden)

    Dhananjay Choudhary

    2014-08-01

    Full Text Available The two basic topologies of switch mode DC-DC converters (Buck and Boost are analyzed with a view of their use in PV (photovoltaic systems, as the photovoltaic generator exhibits non-linear characteristics due to the change in environmental condition and load variation. As the efficiency of PV panels is low it becomes mandatory to extract maximum power from the PV panel at a given period of time. Several MPPT algorithms with different types of converters are being proposed for extracting maximum power from the PV panel. It is found that the nature of load plays an important role in the choice of topology. This paper investigates the implementation issues of Incremental Conductance method with Buck and Boost Converters. Mathematical analysis and desirable steady-state operating point of the converters are derived to give satisfactory maximum power point tracking operation.

  3. Piezoelectric power converter with bi-directional power transfer

    DEFF Research Database (Denmark)

    2014-01-01

    The present invention relates to a bi-directional piezoelectric power converter com¬ prising a piezoelectric transformer. The piezoelectric transformer comprises an input electrode electrically coupled to a primary section of the piezoelectric transformer and an output electrode electrically...... coupled to an output section of the piezoelectric transformer to provide a transformer output signal. A bi-directional switching circuit is coupled between the output electrode and a DC or AC output voltage of the power converter. Forward and reverse current conducting periods of the bi......, a reverse current is conducted through the bi-directional switching circuit from the DC or AC output voltage to the output electrode to discharge the DC or AC output voltage and return power to the primary section of the piezoelectric transformer....

  4. PI and Fuzzy Control Strategies for High Voltage Output DC-DC Boost Power Converter - Hardware Implementation and Analysis

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Blaabjerg, Frede; Siano, Pierluigi

    2016-01-01

    converter with inbuilt voltage-lift technique and overcome the aforementioned deficiencies. Further, the control strategy is adapted based on proportional-integral (P-I) and fuzzy logic, closed-loop controller to regulate the outputs and ensure the performances. Complete hardware prototype of EHV converter......This paper presents the control strategies by Proportional-Integral (P-I) and Fuzzy Logic (FL) for a DC-DC boost power converter for high output voltage configuration. Standard DC-DC converters are traditionally used for high voltage direct current (HVDC) power transmission systems. But, lack its...... performances in terms of efficiency, reduced transfer gain and increased cost with sensor units. Moreover, the internal self-parasitic components reduce the output voltage and efficiency of classical high voltage converters (HVC). This investigation focused on extra high-voltage (EHV) DC-DC boost power...

  5. Load Dump Analysis in a 42/14V DC-DC Converter for Automotive Applications

    Directory of Open Access Journals (Sweden)

    Mohamed Abdualla Shrud

    2013-07-01

    Full Text Available The paper presents a model for a dc-dc centralised based architecture using Matlab/Simulink for load dump analysis. As the electrical load varies for various driving conditions such as day or night, summer or winter; and city or country side, the analysis of load change is a very important parameter for system behaviour. In order to study the 42V power generation dynamic performance under load variations, step change in loads have been investigated. A detailed mathematical model for a 3-phase, 4 kW and 42V Lundell alternator average electrical equivalent circuit along with the DC/DC converter based architectures for dual-voltage systems has been covered in previous publications. Aspects of the steady-state output current capabilities, transient behaviour due to load dump on the 14/42V buses and the behaviour of the system model under different loads are assessed and results discussed. The performance of the 42V Lundell alternator with the interleaved six-phase buck dc-to-dc converter system is modelled using Simulink software to assess the effectiveness of the model and its transient behaviour. The simulated results are presented for the transient characteristics of the system for load dumps.

  6. A current-mode DC-DC buck converter with adaptive zero compensation

    Institute of Scientific and Technical Information of China (English)

    Yang Ling; Dai Guoding; Xu Chongwei; Liu Yuezhi

    2013-01-01

    To achieve fast transient response for a DC-DC buck converter,an adaptive zero compensation circuit is presented.The compensation resistance is dynamically adjusted according to the different output load conditions,and achieves an adequate system phase margin under the different conditions.An improved capacitor multiplier circuit is adopted to realize the minimized compensation capacitance size.In addition,analysis of the small-signal model shows the correctness of the mechanism of the proposed adaptive zero compensation technique.A currentmode DC-DC buck converter with the proposed structure has been implemented in a 0.35 μm CMOS process,and the die size is only 800 × 1040 μm2.The experimental results show that the transient undershoot/overshoot voltage and the recovery times do not exceed 40 mV and 30 μs for a load current variation from 100 mA to 1 A.

  7. Model Based Optimization of Integrated Low Voltage DC-DC Converter for Energy Harvesting Applications

    Science.gov (United States)

    Jayaweera, H. M. P. C.; Muhtaroğlu, Ali

    2016-11-01

    A novel model based methodology is presented to determine optimal device parameters for the fully integrated ultra low voltage DC-DC converter for energy harvesting applications. The proposed model feasibly contributes to determine the maximum efficient number of charge pump stages to fulfill the voltage requirement of the energy harvester application. The proposed DC-DC converter based power consumption model enables the analytical derivation of the charge pump efficiency when utilized simultaneously with the known LC tank oscillator behavior under resonant conditions, and voltage step up characteristics of the cross-coupled charge pump topology. The verification of the model has been done using a circuit simulator. The optimized system through the established model achieves more than 40% maximum efficiency yielding 0.45 V output with single stage, 0.75 V output with two stages, and 0.9 V with three stages for 2.5 kΩ, 3.5 kΩ and 5 kΩ loads respectively using 0.2 V input.

  8. Architectures and Control of Submodule Integrated DC-DC Converters for Photovoltaic Applications

    Energy Technology Data Exchange (ETDEWEB)

    Olalla, C; Clement, D; Rodriguez, M; Maksimovic, D

    2013-06-01

    This paper describes photovoltaic (PV) module architectures with parallel-connected submodule-integrated dc-dc converters (subMICs) that improve efficiency of energy capture in the presence of partial shading or other mismatch conditions. The subMICs are bidirectional isolated dc-dc converters capable of injecting or subtracting currents to balance the module substring voltages. When no mismatches are present, the subMICs are simply shut down, resulting in zero insertion losses. It is shown that the objective of minimum subMIC power processing can be solved as a linear programming problem. A simple close-to-optimal distributed control approach is presented that allows autonomous subMIC control without the need for a central controller or any communication among the subMICs. Furthermore, the proposed control approach is well suited for an isolated-port architecture, which yields additional practical advantages including reduced subMIC power and voltage ratings. The architectures and the control approach are validated by simulations and experimental results using three bidirectional flyback subMICs attached to a standard 180-W, 72-cell PV module, yielding greater than 98% module-level power processing efficiency for a mismatch less than 25%.

  9. A DC-DC converter based powering scheme for the upgrade of the CMS pixel detector

    Science.gov (United States)

    Feld, L.; Karpinski, W.; Klein, K.; Merz, J.; Sammet, J.; Wlochal, M.

    2011-11-01

    Around 2016, the pixel detector of the CMS experiment will be upgraded. The amount of current that has to be provided to the front-end electronics is expected to increase by a factor of two. Since the space available for cables is limited, this would imply unacceptable power losses in the currently installed supply cables. Therefore it is foreseen to place DC-DC converters close to the front-end electronics, allowing the provision of power at higher voltages, thereby facilitating the supply of the required currents with the present cable plant. This conference report introduces the foreseen powering scheme of the pixel upgrade. For the first time, system tests have been conducted with pixel barrel sensor modules, radiation tolerant DC-DC converters and the full power supply chain of the pixel detector. In addition, studies of the stability of different powering schemes under various conditions are summarized. In particular the impact of large and fast load variations, which are related to the bunch structure of the LHC beam, has been studied.

  10. Time delay control for fuel cells with bidirectional DC/DC converter and battery

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Y.B. [Mechanical Engineering Department, Chonnam National University, Gwangju (Korea); Kang, S.J. [Mechatronics Engineering Department, Korea Polytechnic College V, Gwangju (Korea)

    2010-08-15

    Transient behavior is a key property in the vehicular application of proton exchange membrane (PEM) fuel cells. A better control technology is constructed to increase the transient performance of PEM fuel cells. A steady-state isothermal analytical fuel cell model is constructed to analyze mass transfer and water transport in the membrane. To prevent the starvation of air in the PEM fuel cell, time delay control is used to regulate the optimum stoichiometric amount of oxygen, although dynamic fluctuations exist in the PEM fuel cell power. A bidirectional DC/DC converter connects the battery to the DC link to manage the power distribution between the fuel cell and the battery. Dynamic evolution control (DEC) allows for adequate pulse-width modulation (PWM) control of the bidirectional DC/DC converter with fast response. Matlab/Simulink/Simpower simulation is performed to validate the proposed methodology, increase the transient performance of the PEM fuel cell system and satisfy the requirement of energy management. (author)

  11. New topology for DC/DC bidirectional converter for hybrid systems in renewable energy

    Science.gov (United States)

    Lopez, Juan Carlos; Ortega, Manuel; Jurado, Francisco

    2015-03-01

    This article presents a new isolated DC/DC bidirectional converter with soft switching, using a transformer with two voltage taps and two full bridges with insulated-gate bipolar transistors (IGBTs), one on each side of the transformer to be integrated in hybrid systems of renewable energy. A large voltage conversion ratio can be achieved using this converter, in buck and booster modes. Also medium and high DC power can be converted with a good efficiency. Analysis and switching techniques have been reported. To verify the principle of operation, a laboratory prototype of 10 kW has been performed. Experimental results are presented, operating in boost mode. The switching algorithm used has been modelled in MATLAB-Simulink to generate C code. This code has been implemented in a DSP F2812, which has been used to build the prototype.

  12. A High Voltage-lift Efficient Isolated Full Bridge DC-DC Converter

    Directory of Open Access Journals (Sweden)

    A. Gopi

    2014-05-01

    Full Text Available The aim of this study is to propose a high voltage lift isolated full bridge dc-dc converter. The proposed converter consists of an isolation transformer a low turn ratio to obtain high step up voltage gain. The secondary of the transformer connected with two boosting capacitors which connects parallel when power switches switch on period and discharged in series during the switch off period. In addition full bridge converter on primary side consists of clamping diode and capacitor, leakage energy is recycled there by improving conversion efficiency. The proposed circuits simulated using PSIM software form input voltage of 48V, an output of 410 V obtained. These results and operations experimented and validated by implementing in hardware model at 20/40 Vdc, 20 Watts.

  13. Systematic design approach of fuzzy PID stabilizer for DC-DC converters

    Energy Technology Data Exchange (ETDEWEB)

    Guesmi, K.; Essounbouli, N.; Hamzaoui, A. [CReSTIC, IUT de Troyes 09, rue de Quebec BP. 396, 10026 Troyes (France)

    2008-10-15

    DC-DC converters process electrical energy by switching between a fixed number of configurations. The objective of controlling these systems is to provide better performances, ensure closed loop stability and guarantee a simple predictable behaviour. Based on a converter averaged model, we propose, in this paper, a systematic design approach of a fuzzy PID. The choice of controller parameters stands on the whole system stability requirements. Extension of the obtained asymptotic stability to structural stability is presented to show that the developed controller ensures also a simple and predictable behaviour of the converter. Finally, we illustrate the efficiency of the proposed fuzzy PID design approach through simulations in voltage mode as well as in current mode control. (author)

  14. SWITCH MODE PULSE WIDTH MODULATED DC-DC CONVERTER WITH MULTIPLE POWER TRANSFORMERS

    DEFF Research Database (Denmark)

    2009-01-01

    A switch mode pulse width modulated DC-DC power converter comprises at least one first electronic circuit on a input side (1) and a second electronic circuit on a output side (2). The input side (1) and the output side (2) are coupled via at least two power transformers (T1, T2). Each power...... transformer (T1, T2) comprises a first winding (T1a, T2a) arranged in a input side converter stage (3, 4) on the input side (1) and a second winding (T1 b, T2b) arranged in a output side converter stage (5) on the output side (2), and each of the windings (T1a, T1 b, T2a, T2b) has a first end and a second end...

  15. A Compact, Soft-Switching DC-DC Converter for Electric Propulsion

    Science.gov (United States)

    Button, Robert; Redilla, Jack; Ayyanar, Raja

    2003-01-01

    A hybrid, soft-switching, DC-DC converter has been developed with superior soft switching characteristics, high efficiency, and low electro-magnetic interference. This hybrid topology is comprised of an uncontrolled bridge operating at full pulse-width, and a controlled section operating as a conventional phase modulated converter. The unique topology is able to maintain zero voltage switching down to no load operating conditions. A breadboard prototype was developed and tested to demonstrate the benefits of the topology. Improvements were then made to reduce the size of passive components and increase efficiency in preparation for packaging. A packaged prototype was then designed and built, and several innovative packaging techniques are presented. Performance test data is presented that reveals deficiencies in the design of the power transformer. A simple redesign of the transformer windings eliminated the deficiency. Future plans to improve the converter and packaging design are presented along with several conclusions.

  16. Trans-inverse (Tx−1) high step-up DC-DC converter

    DEFF Research Database (Denmark)

    Siwakoti, Yam Prasad; Blaabjerg, Frede; Loh, Poh Chiang

    2015-01-01

    In this paper, a new magnetically coupled single-switch non-isolated dc-dc converter with a high voltage gain is proposed. The new topology utilizes a transformer to boost the output voltage. However, unlike other converter topologies with transformer or coupled magnetics, the voltage gain...... in the proposed topology is increased by reducing the turns ratio of the transformer. Hence the name Trans-inverse (Tx−1) is given to represent the inverse transformer principle of operation of the proposed converter. The new topology draws a continuous current from the source, which is required for many...... renewable sources. Further, the leakage energy of the transformer is recycled and transferred to the load using a passive regenerative snubber circuit. In addition, the new topology has dc-current-blocking capacitors, which avoids saturation in the transformer core. Simulation and experimental results have...

  17. Design of a total-dose radiation hardened monolithic CMOS DC-DC boost converter

    Energy Technology Data Exchange (ETDEWEB)

    Liu Zhi; Yu Hongbo; Liu Youbao [Xi' an Institute of Microelectronics Technology, Xi' an 710054 (China); Ning Hongying, E-mail: liuzhi6048@126.com [Xi' an University of Technology, Xi' an 710048 (China)

    2011-07-15

    This paper presents the design and implementation of a monolithic CMOS DC-DC boost converter that is hardened for total dose radiation. In order to improve its radiation tolerant abilities, circuit-level and device-level RHBD (radiation-hardening by design) techniques were employed. Adaptive slope compensation was used to improve the inherent instability. The H-gate MOS transistors, annular gate MOS transistors and guard rings were applied to reduce the impact of total ionizing dose. A boost converter was fabricated by a standard commercial 0.35 {mu}m CMOS process. The hardened design converter can work properly in a wide range of total dose radiation environments, with increasing total dose radiation. The efficiency is not as strongly affected by the total dose radiation and so does the leakage performance. (semiconductor integrated circuits)

  18. Comparison of control structures for a bidirectional high-frequency dc-dc converter

    Science.gov (United States)

    Himmelstoss, Felix A.; Kolar, Johann W.; Zach, Franz C.

    1989-08-01

    A system for dc-dc power conversion based on a buck-boost converter topology is presented. It makes power flow in both directions possible. The possibility of bidirectional power flow is useful for certain applications, such as uninterruptable power supplies. Starting from a structural diagram the transfer function of the system is derived. The controller for the converter is then designed. It is made up of a simple voltage controller, a voltage controller with an inner loop current controller (cascade control) and with two kinds of state space control. The transfer functions of the different system parts are derived and dimensioning guidelines for the controller sections are presented. The closed loop behavior of the bidirectional converter for the different control structures is analyzed based on simulation using duty cycle averaging. Bodediagrams and step responses are shown.

  19. Load adaptive start-up scheme for synchronous boost DC-DC converter

    Science.gov (United States)

    Guoding, Dai; Wenliang, Xiu; Yuezhi, Liu; Yawei, Qi; Zuqi, Dong

    2016-10-01

    This paper presents a load adaptive soft-start scheme through which the inductor current of the synchronous boost DC-DC converter can trace the load current at the start-up stage. This scheme effectively eliminates the inrush-current and over-shoot voltage and improves the load capability of the converter. According to the output voltage, the start-up process is divided into three phases and at each phase the inductor current is limited to match the load. In the pre-charge phase, a step-increasing constant current gives a smooth rise of the output voltage which avoids inrush current and ensures the converter successfully starts up at different load situations. An additional ring oscillator operation phase enables the converter to start up as low as 1.4 V. When the converter enters into the system loop soft-start phase, an output voltage and inductor current detection methods make the transition of the phases smooth and the inductor current and output voltage rise steadily. Effective protection circuits such as short-circuit protection, current limit circuit and over-temperature protection circuit are designed to guarantee the safety and reliability of the chip during the start-up process. The proposed start-up circuit is implemented in a synchronous boost DC-DC converter based on TSMC 0.35 μm CMOS process with an input voltage range 1.4-4.2 V, and a steady output voltage 5 V, and the switching frequency is 1 MHz. Simulation results show that inrush current and overshoot voltage are suppressed with a load range from 0-2.1 A, and inductor current is as low as 259 mA when the output shorts to the ground.

  20. A Stable Control Strategy for Input-Series Output-Series Connected Boost half Bridge DC-DC Converter

    Directory of Open Access Journals (Sweden)

    Shahnawaz Farhan Khahro

    2013-07-01

    Full Text Available Boost half bridge DC-DC converters in the combination of an input-series and output-series (ISOS connected configuration with a stable control strategy has been investigated in this paper. A stable control strategy comprises of two loops that are current loop and voltage loop. The reference to the current loop has been chosen from the input side of the DC-DC converter. The reference to the voltage loop has been selected from the output side of the DC-DC converter. Such a reference makes the circuit configuration simple, easy and eventually results in reduced cost. The control strategy for input-series output-series (ISOS configuration of DC-DC converters is proposed to achieve equal input voltage sharing (IVS as well output voltage sharing (OVS. Furthermore, in this paper, the performance of the stable control strategy for input-series output-series (ISOS boost half bridge DC-DC converter has been observed not only for the fixed but also for the varying and continuously varying load. The proposed Stable control scheme has been developed by modeling it on MATLAB using Simulink and Simpower toolboxes. The operation of the proposed stable control strategy has been found to be satisfactory.

  1. The Chaotic-Based Control of Three-Port Isolated Bidirectional DC/DC Converters for Electric and Hybrid Vehicles

    Directory of Open Access Journals (Sweden)

    Zheng Wang

    2016-01-01

    Full Text Available Three-port isolated (TPI bidirectional DC/DC converters have three energy ports and offer advantages of large voltage gain, galvanic isolation ability and high power density. For this reason this kind of converters are suitable to connect different energy sources and loads in electric and hybrid vehicles. The purpose of this paper is to propose chaotic modulation and the related control scheme for TPI bidirectional DC/DC converters, in such a way that the switching harmonic peaks can be suppressed in spectrum and the conducted electromagnetic interference (EMI is reduced. Two chaotic modulation strategies, namely the continuously chaotic modulation and the discretely chaotic modulation are presented. These two chaotic modulation strategies are applied for TPI bidirectional DC/DC converters with shifted-phase angle based control and phase-shifted PWM control. Both simulation and experiments are given to verify the validity of the proposed chaotic modulation-based control schemes.

  2. ASIC and FPGA based DPWM architectures for single-phase and single-output DC-DC converter: a review

    Science.gov (United States)

    Chander, Subhash; Agarwal, Pramod; Gupta, Indra

    2013-12-01

    Pulse width modulation (PWM) has been widely used in power converter control. This paper presents a review of architectures of the Digital Pulse Width Modulators (DPWM) targeting digital control of switching DC-DC converters. An attempt is made to review the reported architectures with emphasis on the ASIC and FPGA implementations in single phase and single-output DC-DC converters. Recent architectures using FPGA's advanced resources for achieving the resolution higher than classical methods have also been discussed. The merits and demerits of different architectures, and their relative comparative performance, are also presented. The Authors intention is to uncover the groundwork and the related references through this review for the benefit of readers and researchers targeting different DPWM architectures for the DC-DC converters.

  3. Five-Level Active-Neutral-Point-Clamped DC/DC Converter for Medium-Voltage DC Grids

    DEFF Research Database (Denmark)

    Liu, Dong; Deng, Fujin; Chen, Zhe

    2017-01-01

    effectively eliminate high voltage leaps caused by the dead time effect. In addition, a capacitor voltage control strategy is proposed for the 5L-ANPC dc/dc converter to ensure the balanced flying capacitor voltage and desired five-level voltage waveforms. Finally, simulation and experimental studies......This paper proposes a five-level active-neutralpoint- clamped (5L-ANPC) dc/dc converter for applications in medium voltage dc (MVDC) grids. A modulation strategy is proposed for the 5L-ANPC dc/dc converter to generate multilevel voltage waveforms, which can effectively reduce voltage change rate dv...... are conducted, and the results have verified the proposed converter and control strategies....

  4. A Simple MPPT Algorithm for Novel PV Power Generation System by High Output Voltage DC-DC Boost Converter

    DEFF Research Database (Denmark)

    Sanjeevikumar, Padmanaban; Grandi, Gabriele; Wheeler, Patrick

    2015-01-01

    This paper presents the novel topology of Photo Voltaic (PV) power generation system with simple Maximum Power Point Tracking (MPPT) algorithm in voltage operating mode. Power circuit consists of high output voltage DC-DC boost converter which maximizes the output of PV panel. Usually traditional...... of DC-DC converters for PV integration. Hence, to overcome these difficulties this paper investigates a DC-DC boost converter together with the additional parasitic component within the circuit to provide high output voltages for maximizing the PV power generation. The proposed power system circuit...... substantially improves the high output-voltage by a simple MPPT closed loop proportional-integral (P-I) controller, and requires only two sensor for feedback needs. The complete numerical model of the converter circuit along with PV MPPT algorithm is developed in numerical simulation (Matlab/Simulink) software...

  5. High-Voltage 1-kW dc/dc Converter Developed for Low-Temperature Operation

    Science.gov (United States)

    Patterson, Richard L.

    1998-01-01

    Recently, Lewis developed and demonstrated a high-voltage, 1-kW dc/dc converter that operates from room temperature to -184 C. A power supply designed for use in a NASA ion beam propulsion system was utilized as a starting point for the design of a low- (wide-) temperature dc/dc converter. For safety, we decided to halve the output voltage and power level, so the converter was designed for an 80-Vdc input and a 550-Vdc output at 1 kW.

  6. A Reduced-Part, Triple-Voltage DC-DC Converter for EV/HEV Power Management

    Energy Technology Data Exchange (ETDEWEB)

    Su, Gui-Jia [ORNL; Tang, Lixin [ORNL

    2009-01-01

    Electrical power systems in future hybrid and fuel cell vehicles may consist of three voltage nets: 14 V, 42 V, and high voltage (>200 V) buses. A soft-switched, bidirectional dc-dc converter that uses only four switches was proposed for interconnecting the three nets. This paper presents a reduced-part dc-dc converter, which decreases the converter cost while retaining all the favorable features of the original topology. Experimental data are included to verify a simple power flow control scheme.

  7. Decoupled Power Solution for Dual-input Isolated DC-DC Converters Using Four Quadrants Integrated Transformers (FQIT)

    DEFF Research Database (Denmark)

    Ouyang, Ziwei; Andersen, Michael A. E.; Thomsen, Ole Cornelius

    2012-01-01

    A common limitation of power coupling effect in some known multiple-input dc-dc converters has been addressed in many literatures. In order to overcome this limitation, a new concept for decoupling the primary windings in the integrated multiple-winding transformers based on 3-dimensional (3D....... In order to verify the feasibility of the FQIT in multiple-input converter, a dual-input isolated boost dc-dc converter employing with the FQIT is designed and tested. The results have excellently demonstrated that the two input power stages can be operated independently and the correctness of all...

  8. A Bidirectional, Triple-Voltage DC-DC Converter for Hybrid and Fuel Cell Vehicle Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Su, Gui-Jia [ORNL; Tang, Lixin [ORNL

    2007-01-01

    Electrical power systems in future hybrid and fuel cell vehicles may employ three voltage (14V, 42V and high voltage (HV)) nets. These will be necessary to accommodate existing 14V loads as well as efficiently handle new heavy loads at the 42V net and an electrical traction drive on the HV bus. A low-cost bi-directional dc-dc converter was proposed in (10) for connecting the three voltage nets. The converter consists of two half-bridges and a high-frequency transformer; thus minimizing the number of switching devices and their associated gate driver components. One salient feature is that the half-bridge on the 42V bus is also utilized to provide the 14V bus by operating its duty ratio around an atypical value of 1/3. This eliminates the need for an additional 14V/42V converter. Moreover, it makes use of the parasitic capacitance of the switches and the transformer leakage inductance for soft-switching; no extra active switches or passive resonant components are required. The use of half-bridges makes the topology suitable for interleaved multi-phase configurations as a means to increase the power level because the capacitor legs can be shared. This paper presents simulation and experimental results on an interleaved two-phase arrangement rated at 4.5 kW. Also discussed are the benefits of operating with the atypical duty ratio on the transformer and a preferred multi-phase configuration to minimize capacitor ripple currents.

  9. Design of high efficiency dual-mode buck DC-DC converter

    Energy Technology Data Exchange (ETDEWEB)

    Lai Xinquan; Zeng Huali; Ye Qiang; He Huisen; Zhang Shasha; Sun Yuqing, E-mail: zenghuali4213@126.com, E-mail: xqlai@mail.xidian.edu.cn [Institute of Electronic CAD, Xidian University, Xi' an 710071 (China)

    2010-11-15

    A buck DC-DC switching regulator with high efficiency is implemented by automatically altering the modulation mode according to load current, and it can operate with an input range of 4.5 to 30 V. At light load current, the converter operates in skip mode. The converter enters PWM mode operation with increasing load current. It reduces the switching loss at light load and standby state, which results in prolonging battery lifetime and stand-by time. Meanwhile, externally adjustable soft-start minimizes the inrush supply current and avoids the overshoot of output voltage at initial startup. The regulator is fabricated by a 0.6 {mu}m CDMOS process. The test results show that, under the condition of 3.3 V output, the efficiency is up to 64% at 5 mA and the maximum efficiency is 95.5%.

  10. Conventional control and fuzzy control of a dc-dc converter for machine drive

    Energy Technology Data Exchange (ETDEWEB)

    Radoi, C.; Florescu, A. [Department of Power Electronics `Politecnica` University Bucharest (Romania)

    1997-12-31

    Fuzzy logic or fuzzy set theory is recently getting increasing emphasis in process control applications. The paper describes an application of fuzzy logic in speed control system that uses a dc-dc converter. The fuzzy control is used to linearize the family of external characteristics of the converter in discontinuous-conduction mode occurring at light load and/or high speed. In order to compare the conventional control with the fuzzy logic control, algorithms have been developed in detail and verified by Microsoft Excel simulation. The simulation study indicates that fuzzy control is a good alternative for conventional control methods, being used particularly in non-linear complex systems ill defined or totally unknown. Where the mathematical model exists, it is useful. The applications of fuzzy set theory in power electronics are almost entirely new; fuzzy logic seems to have a lot of premises in the large industrial control field. (orig.) 2 refs.

  11. Low-temperature operation of a Buck DC/DC converter

    Science.gov (United States)

    Ray, Biswajit; Gerber, Scott S.; Patterson, Richard L.; Myers, Ira T.

    1995-01-01

    Low-temperature (77 K) operation of a 42/28 V, 175 W, 50 kHz PWM Buck DC/DC converter designed with commercially available components is reported. Overall, the converter losses decreased at 77 K compared to room temperature operation. A full-load efficiency of 97 percent was recorded at liquid-nitrogen temperature, compared to 95.8 percent at room temperature. Power MOSFET operation improved significantly where as the output rectifier operation deteriorated at low-temperature. The performance of the output filter inductor and capacitor did not change significantly at 77 K compared to room temperature performance. It is possible to achieve high-density and high efficiency power conversion at low-temperatures due to improved electronic, electrical and thermal properties of materials.

  12. SSP Technology Investigation of a High-Voltage DC-DC Converter

    Science.gov (United States)

    Pappas, J. A.; Grady, W. M.; George, Patrick J. (Technical Monitor)

    2002-01-01

    The goal of this project was to establish the feasibility of a high-voltage DC-DC converter based on a rod-array triggered vacuum switch (RATVS) for the Space Solar Power system. The RATVS has many advantages over silicon and silicon-carbide devices. The RATVS is attractive for this application because it is a high-voltage device that has already been demonstrated at currents in excess of the requirement for an SSP device and at much higher per-device voltages than existing or near-term solid state switching devices. The RATVS packs a much higher specific power rating than any solid-state device and it is likely to be more tolerant of its surroundings in space. In addition, pursuit of an RATVS-based system would provide NASA with a nearer-term and less expensive power converter option for the SSP.

  13. DC-DC converters in 0.35μm CMOS technology

    Science.gov (United States)

    Michelis, S.; Allongue, B.; Blanchot, G.; Faccio, F.; Fuentes, C.; Orlandi, S.; Saggini, S.; Cengarle, S.; Ongaro, F.

    2012-01-01

    In view of the upgrade of the LHC experiments, we are developing custom DC/DC converters for a more efficient power distribution scheme. A new prototype have been integrated in ASICs in the selected 0.35μm commercial high voltage technology that has been successfully tested for all radiation effects: TID, displacement damage and Single Event Burnout. This converter has been optimized for high efficiency and improved radiation tolerance. Amongst the new features the most relevant are the presence of internal linear regulators, protection circuits with a state-machine and a new pinout for a modified assembly in package in order to reduce conductive losses. This paper illustrates the design of the prototype followed by functional and radiation tests.

  14. Electrothermal model of choking-coils for the analysis of dc-dc converters

    Energy Technology Data Exchange (ETDEWEB)

    Gorecki, Krzysztof, E-mail: gorecki@am.gdynia.pl [Gdynia Maritime University, Department of Marine Electronics, Morska 83, Gdynia (Poland); Detka, Kalina [Pomeranian Higher School in Gdynia, Opata Hackiego 8-10, Gdynia (Poland)

    2012-09-01

    The paper concerns modelling the choking-coil for the needs of the electrothermal analysis of dc-dc converters. A new electrothermal model of the choking-coil is proposed. This model is dedicated for SPICE software and it takes into account nonlinearity of the dependences of the inductance on the current, selfheating and mutual thermal interactions between the core and the winding. The structure of this model is described in detail and its correctness is experimentally verified for the choking-coils with the ferrite and powder cores. Both the characteristics of the choking-coils and the buck converter with these choking-coils were considered. The satisfying agreement between the results of calculations and measurements is obtained.

  15. Maximum Power Point Tracking Controller for Thermoelectric Generators with Peak Gain Control of Boost DC-DC Converters

    Science.gov (United States)

    Park, Jungyong; Kim, Shiho

    2012-06-01

    An analog maximum power point tracking (MPPT) circuit for a thermoelectric generator (TEG) is proposed. We show that the peak point of the voltage conversion gain of a boost DC-DC converter with an input voltage source having an internal resistor is the maximum power point of the TEG. The key characteristic of the proposed MPPT controller is that the duty ratio of the input clock pulse to the boost DC-DC converter shifts toward the maximum power point of the TEG by seeking the peak gain point of the boost DC-DC converters. The proposed MPPT technique provides a simple and useful analog MPPT solution, without employing digital microcontroller units.

  16. A 10 kW dc-dc converter using IGBTs with active snubbers. [Insulated Gate Bipolar Transistor

    Science.gov (United States)

    Masserant, Brian J.; Shriver, Jeffrey L.; Stuart, Thomas A.

    1993-01-01

    This full bridge dc-dc converter employs zero voltage switching (ZVS) on one leg and zero current switching (ZCS) on the other. This technique produces exceptionally low IGBT switching losses through the use of an active snubber that recycles energy back to the source. Experimental results are presented for a 10 kW, 20 kHz converter.

  17. Advanced DC-DC converter for power conditioning in hydrogen fuel cell systems

    Energy Technology Data Exchange (ETDEWEB)

    Kovacevic, G.; Tenconi, A.; Bojoi, R. [Department of Electrical Engineering, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino (Italy)

    2008-06-15

    The fuel cell (FC) generators can produce electric energy directly from hydrogen and oxygen. The DC voltage generated by FC is generally low amplitude and it is not constant, depending on the operating conditions. Furthermore, FC systems have dynamic response that is slower than the transient responses typically requested by the load. For this reason, in many applications the FC generators must be interfaced with other energy/power sources by means of an electronic power converter. An advanced full-bridge (FB) DC-DC converter, which effectively achieves zero-voltage switching and zero-current switching (ZVS-ZCS), is proposed for power-conditioning (PC) in hydrogen FC applications. The operation and features of the converter are analyzed and verified by simulations results. The ZVS-ZCS operation is obtained by means of a simple auxiliary circuit. Introduction of the soft-switching operation in PC unit brings improvements not only from the converter efficiency point of view, but also in terms of increased converter power density. Quantitative analysis of hard and soft-switching operating of the proposed converter is also made, bringing in evidence the benefits of soft-switching operation mode. The proposed converter can be a suitable solution for PC in hydrogen FC systems, especially for the medium to high-power applications. (author)

  18. DC-DC converters for the upgrades of the CMS tracker

    Energy Technology Data Exchange (ETDEWEB)

    Sammet, Jan; Feld, Lutz; Karpinski, Waclaw; Klein, Katja; Merz, Jennifer; Wehner, Jakob; Wlochal, Michael [RWTH Aachen University, I. Physikalisches Instiut B (Germany)

    2011-07-01

    Within the present decade, it is foreseen to gradually increase the instantaneous luminosity of the LHC to 1-2.10{sup 34} cm{sup -2}s{sup -1}. Around 2020, it is intended to increase the luminosity further, to about 5.10{sup 34} cm{sup -2}s{sup -1}. To ensure and improve its physics performance, CMS is going to exchange its pixel detector around 2016. Four years later the complete tracker is going to be replaced by a new development. The use of DC-DC converters is foreseen for both of these upgrades. Radiation tolerant converters developed by working groups at CERN and Aachen match the requirements of the new pixel detector already. However, further work is required to integrate the converters on system level and to ensure their save and reliable operation. The status of this work is presented. Building a new tracking detector equipped with converters, raises several additional challenges. In particular the noise performance of the converters and their efficiency at large conversion ratios still has to be improved. The coil, used by the converters to buffer energy, has a significant impact on both of these issues. Effort has been put into the optimization of converter coils, as well as into the exploration and minimization of noise radiated by the coils. The talk gives a summary of the results of this work.

  19. Large step-down DC-DC converters with reduced current stress

    Energy Technology Data Exchange (ETDEWEB)

    Ismail, Esam H. [Department of Electrical Engineering, College of Technological Studies, P.O. Box 35007, 36051 Al-Shaab (Kuwait)

    2009-02-15

    In this paper, several DC-DC converters with large voltage step-down ratios are introduced. A simple modification in the output section of the conventional buck and quadratic converters can effectively extend the duty-cycle range. Only two additional components (an inductor and diode) are necessary for extending the duty-cycle range. The topologies presented in this paper show an improvement in the duty-cycle (about 40%) over the conventional buck and quadratic converters. Consequently, they are well suited for extreme step-down voltage conversion ratio applications. With extended duty-cycle, the current stress on all components is reduced, leading to a significant improvement of the system losses. The principle of operation, theoretical analysis, and comparison of circuit performances with other step-down converters is discussed regarding voltage and current stress. Experimental results of one prototype rated 40-W and operating at 100 kHz are provided in this paper to verify the performance of this new family of converters. The efficiency of the proposed converters is higher than the quadratic converters. (author)

  20. A Two-stage DC-DC Converter for the Fuel Cell-Supercapacitor Hybrid System

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2009-01-01

    A wide input range multi-stage converter is proposed with the fuel cells and supercapacitors as a hybrid system. The front-end two-phase boost converter is used to optimize the output power and to reduce the current ripple of fuel cells. The supercapacitor power module is connected by push-pull-f...... and designed. A 1kW prototype controlled by TMS320F2808 DSP is built in the lab. Simulation and experimental results confirm the feasibility of the proposed two stage dc-dc converter system.......A wide input range multi-stage converter is proposed with the fuel cells and supercapacitors as a hybrid system. The front-end two-phase boost converter is used to optimize the output power and to reduce the current ripple of fuel cells. The supercapacitor power module is connected by push......-pull-forward half bridge (PPFHB) converter with coupled inductors in the second stage to handle the slow transient response of the fuel cells and realize the bidirectional power flow control. Moreover, this cascaded structure simplifies the power management. The control strategy for the whole system is analyzed...

  1. A dual VCDL DLL based gate driver for zero-voltage-switching DC-DC converter

    Science.gov (United States)

    Xin, Tian; Xiangxin, Liu; Wenhong, Li

    2010-07-01

    This paper presents a dual voltage-controlled-delay-line (VCDL) delay-lock-loop (DLL) based gate driver for a zero-voltage-switching (ZVS) DC-DC converter. Using the delay difference of two VCDLs for the dead time control, the dual VCDL DLL is able to implement ZVS control with high accuracy while keeping good linearity performance of the DLL and low power consumption. The design is implemented in the CSM 2P4M 0.35 μm CMOS process. The measurement results indicate that an efficiency improvement of 2%-4% is achieved over the load current range from 100 to 600 mA at 4 MHz switching frequency with 3.3 V input and 1.3 V output voltage.

  2. A dual VCDL DLL based gate driver for zero-voltage-switching DC-DC converter

    Energy Technology Data Exchange (ETDEWEB)

    Tian Xin; Liu Xiangxin; Li Wenhong, E-mail: wenhongli@fudan.edu.c [State Key Laboratory of ASIC and System, Fudan University, Shanghai 201203 (China)

    2010-07-15

    This paper presents a dual voltage-controlled-delay-line (VCDL) delay-lock-loop (DLL) based gate driver for a zero-voltage-switching (ZVS) DC-DC converter. Using the delay difference of two VCDLs for the dead time control, the dual VCDL DLL is able to implement ZVS control with high accuracy while keeping good linearity performance of the DLL and low power consumption. The design is implemented in the CSM 2P4M 0.35 {mu}m CMOS process. The measurement results indicate that an efficiency improvement of 2%-4% is achieved over the load current range from 100 to 600 mA at 4 MHz switching frequency with 3.3 V input and 1.3 V output voltage.

  3. Automated synthesis of power circuit single ended DC-DC converters

    Science.gov (United States)

    Vakovsky, Dimiter; Hinov, Nikolay

    2016-12-01

    Guaranteeng the parameters in the output of the power electronics device is of great importance for achieving the desired quality of the process of energy conversion. The combined methods for realization of the electronic devices with guaranteed parameters requires the usage of systematic approach in the realization of the power electronics device - from the stage of the parameter formulation to the receiving of the end product. In the investigation the application of the modelling and software products for the research are growing more and more. In that relation it is necessary the creation of a common programming environment in which the diversity of application programs can operate. In the paper is present an automated synthesis and design of single-transistor dc-dc converters.

  4. DC-DC switching converter based power distribution vs serial power distribution EMC strategies

    CERN Document Server

    Arteche, F; Iglesias, M; Rivetta, C; Arcega, F G; Vila, I

    2009-01-01

    This paper presents a detailed and comparative analysis from the electromagnetic compatibility point of view of the proposed power distributions for the SLHC tracker up-grade. The main idea is to identify and quantify the noise sources, noise distribution at the system level and the sensitive areas in the front-end electronics corresponding to both proposed topologies: The DC-DC converter based power distribution and the serial power distribution. These studies will be used to define critical points on both systems to be studied and prototyped to ensure the correct integration of the system taking critically into account the electromagnetic compatibility. This analysis at the system level is crucial to ensure the final performance of the detector using non conventional power distributions, avoiding interference problems and excessive losses that can lead to catastrophic failures or expensive and un-practical solutions.

  5. Online humidification diagnosis of a PEMFC using a static DC-DC converter

    Energy Technology Data Exchange (ETDEWEB)

    Hinaje, M.; Sadli, I.; Martin, J.-P.; Thounthong, P.; Rael, S.; Davat, B. [GREEN - Institut National Polytechnique de Lorraine 2, Avenue de la Foret de Haye, 54516 Vandoeuvre-les-Nancy (France)

    2009-03-15

    This paper deals with the online checking of the humidification of a Proton Exchange Membrane Fuel Cell (PEMFC). Indeed, drying or flooding can decrease the performance of the PEMFC and even lead to its destruction. An online humidification diagnosis can allow a real-time control. A good indicator of the membrane humidification state is its internal resistance. As known, the membrane ionic conductivity increases with the membrane water content. This resistance can be calculated at high frequency by dividing the voltage variation by the current variation. The proposed scheme makes use of measurements of current and voltage ripples coming from the association of a static DC-DC converter and the fuel cell. The experiment thus consists in computing the internal resistance in wet and dry conditions. (author)

  6. AC Voltage Control of DC/DC Converters Based on Modular Multilevel Converters in Multi-Terminal High-Voltage Direct Current Transmission Systems

    Directory of Open Access Journals (Sweden)

    Rui Li

    2016-12-01

    Full Text Available The AC voltage control of a DC/DC converter based on the modular multilevel converter (MMC is considered under normal operation and during a local DC fault. By actively setting the AC voltage according to the two DC voltages of the DC/DC converter, the modulation index can be near unity, and the DC voltage is effectively utilized to output higher AC voltage. This significantly decreases submodule (SM capacitance and conduction losses of the DC/DC converter, yielding reduced capital cost, volume, and higher efficiency. Additionally, the AC voltage is limited in the controllable range of both the MMCs in the DC/DC converter; thus, over-modulation and uncontrolled currents are actively avoided. The AC voltage control of the DC/DC converter during local DC faults, i.e., standby operation, is also proposed, where only the MMC connected on the faulty cable is blocked, while the other MMC remains operational with zero AC voltage output. Thus, the capacitor voltages can be regulated at the rated value and the decrease of the SM capacitor voltages after the blocking of the DC/DC converter is avoided. Moreover, the fault can still be isolated as quickly as the conventional approach, where both MMCs are blocked and the DC/DC converter is not exposed to the risk of overcurrent. The proposed AC voltage control strategy is assessed in a three-terminal high-voltage direct current (HVDC system incorporating a DC/DC converter, and the simulation results confirm its feasibility.

  7. Integrated Circuit of CMOS DC-DC Buck Converter with Differential Active Inductor

    Directory of Open Access Journals (Sweden)

    Kaoutar Elbakkar

    2011-11-01

    Full Text Available In this paper, we propose a new design of DC-DC buck converter (BC, which the spiral inductor is replaced by a differential gyrator with capacitor load (gyrator-C implemented in 0.18um CMOS process. The gyrator-C transforms the capacitor load (which is the parasitic capacitor of MOSFETS to differential active inductor DAI. The low-Q value of DAI at switching frequency of converter (few hundred kHz is boosted by adding a negative impedance converter (NIC. The transistor parameters of DAI and NIC can be properly chosen to achieve the desirable value of equivalent inductance L (few tens H, and the maximum-Q value at the switching frequency, and thus the efficiency of converter is improved. Experimental results show that the converter supplied with an input voltage of 1V, provides an output voltage of 0.74V and output ripple voltage of 10mV at 155 kHz and Q-value is maximum (#8776;4226 at this frequency.

  8. Bifurcation boundary conditions for current programmed PWM DC-DC converters at light loading

    Science.gov (United States)

    Fang, Chung-Chieh

    2012-10-01

    Three types of bifurcations (instabilities) in the PWM DC-DC converter at light loading under current mode control in continuous-conduction mode (CCM) or discontinuous-conduction mode (DCM) are analysed: saddle-node bifurcation (SNB) in CCM or DCM, border-collision bifurcation during the CCM-DCM transition, and period-doubling bifurcation in CCM. Different bifurcations occur in some particular loading ranges. Bifurcation boundary conditions separating stable regions from unstable regions in the parametric space are derived. A new methodology to analyse the SNB in the buck converter based on the peak inductor current is proposed. The same methodology is applied to analyse the other types of bifurcations and converters. In the buck converter, multiple stable/unstable CCM/DCM steady-state solutions may coexist. Possibility of multiple solutions deserves careful study, because an ignored solution may merge with a desired stable solution and make both disappear. Understanding of SNB can explain some sudden disappearances or jumps of steady-state solutions observed in switching converters.

  9. Design and implementation of a switched capacitor-based embedded hybrid DC-DC converter

    Science.gov (United States)

    Bhattacharyya, Kaushik; Mandal, Pradip

    2012-06-01

    Here, we propose an integrated hybrid DC-DC converter suitable for high drop-out energy conscious applications. In the hybrid converter topology, along with a linear regulator two switched capacitors are used to store and recycle charge for better power efficiency. Without significant power loss the switched capacitors step down the supply voltage for the linear regulator working in low drop-out mode. The linear regulator, on the other hand, attenuates the voltage ripple that originates from the switched capacitors converter on its power supply rejection ratio. It also helps for line and load regulation. Additionally, a synthesised counter ripple is injected through the linear regulator to further reduce the output ripple. With these two techniques, for a moderate load current and an acceptable output ripple, the switching and load capacitors are reduced to a value which can be implemented within the chip. The proposed integrated converter circuit has been designed, implemented and tested in a 0.18 mm CMOS process for 3.3-1.3V conversion. With two switching capacitors of 210 pF each and 100 pF load capacitor, more than 13 mA of load current, measured peak-to-peak output voltage ripple is 146 mV. The achieved measured power efficiency is 64.97%. Exhaustive silicon characterisation of the converter is done to observe the power efficiency and ripple variation at different frequency of operations.

  10. Performance of a Voltage Step-Up/Step-Down Transformerless DC/DC Converter: Analytical Model

    Science.gov (United States)

    Suskis, P.; Rankis, I.

    2012-01-01

    The authors present an analytical model for a voltage step-up/step-down DC/DC converter without transformers. The proposed topology is a combination of classic buck and boost converters in one single circuit but with differing operational principles. The converter is developed for a wind power autonomous supply system equipped with a hydrogen electrolytic tank and a fuel cell for energy stabilization. The main power source of the hydrogen-based autonomous supply system is energized by a synchronous generator operating on permanent magnets and equipped with a diode bridge. The input voltage of the converter in this case varies in the range 0-700 V, while its output DC voltage must be 540 V according to the demand of other parts of the system. To maintain the rated voltage, a special electrical load regulation is introduced. The calculations of the converter, the generator (equipped with a diode bridge) as element of the power system supply joint, and the load replaced by resistance are verified with PSIM software.

  11. A High Efficiency DC-DC Converter Topology Suitable for Distributed Large Commercial and Utility Scale PV Systems

    Energy Technology Data Exchange (ETDEWEB)

    Agamy, Mohammed S; Harfman-Todorovic, Maja; Elasser, Ahmed; Steigerwald, Robert L; Sabate, Juan A; Chi, Song; McCann, Adam J; Zhang, Li; Mueller, Frank

    2012-09-01

    In this paper a DC-DC power converter for distributed photovoltaic plant architectures is presented. The proposed converter has the advantages of simplicity, high efficiency, and low cost. High efficiency is achieved by having a portion of the input PV power directly fed forward to the output without being processed by the converter. The operation of this converter also allows for a simplified maximum power point tracker design using fewer measurements

  12. Energy Evaluation for DC/DC Converters in DC-Based Wind Farms

    Energy Technology Data Exchange (ETDEWEB)

    Max, Lena

    2007-02-15

    In this thesis the suitability of three topologies for DC/DC converters in a DC wind farm grid is investigated from an energy efficiency and energy production cost point of view. The three selected topologies are the fullbridge converter, the single active bridge converter and the series parallel resonant converter. The losses are calculated for all three topologies as a function of the wind speed considering the losses in the semiconductor components and in the transformer. To obtain the average losses, the losses for each converter are integrated over the wind distribution for different average wind speeds. It is found that the resonant converter has the lowest losses of the three types for the DC wind farm application with power losses of about 2.0 - 2.5 % of the input power and the fullbridge converter has slightly higher losses with 2.3 - 3.5 % losses depending on the position in the wind turbine grid. The single active bridge converter has considerably higher losses than the other two topologies with 3.5 - 5.0 % losses. It is shown that the variable operating conditions create problems for all three converters, and as mentioned the single active bridge converter is most affected by the wide range of operation conditions. When comparing the resonant converter and the fullbridge converter, the fullbridge converter has a smaller transformer as well as lower peak current and peak voltage, but also a higher number of diode modules in the output bridge. Comparing the contribution to the energy production cost for the converters, the topology with the lowest contribution varies between the positions in the wind turbine grid. For some positions, the cost of the higher losses for the fullbridge converter are compensated by lower investment cost for the fullbridge converter compared to the resonant converter. Considering the resonant capacitor, the higher peak voltage and the variable frequency control for the resonant converter, the fullbridge converter is here found

  13. High step-up isolated efficient single switch DC-DC converter for renewable energy source

    Directory of Open Access Journals (Sweden)

    A. Gopi

    2014-12-01

    Full Text Available In this paper, an isolated high step-up single switch DC-DC converter for renewable energy source is proposed. In the proposed converter high step-up voltage is obtained by single power switching technique that operates low duty cycle with isolated transformer inductors and switched capacitors and power diodes. The disadvantage of conventional converters is that it has high duty ratio and high voltage stress on power devices with less efficiency. The proposed converter eliminates the switching losses and recycles the leakage energy which includes reverse recovery energy of the power diode by using passive clamp circuit. To achieve high output voltage gain, the isolated transformer primary terminal and secondary terminal are connected in series during switching operation. PSIM software has been used for simulation. Simulation circuit is analyzed at 40Vdc/400Vdc, 200 W and this operation is validated by implementing in the hardware model at 12Vdc/120Vdc, 60 W.

  14. An optimal current observer for predictive current controlled buck DC-DC converters.

    Science.gov (United States)

    Min, Run; Chen, Chen; Zhang, Xiaodong; Zou, Xuecheng; Tong, Qiaoling; Zhang, Qiao

    2014-05-19

    In digital current mode controlled DC-DC converters, conventional current sensors might not provide isolation at a minimized price, power loss and size. Therefore, a current observer which can be realized based on the digital circuit itself, is a possible substitute. However, the observed current may diverge due to the parasitic resistors and the forward conduction voltage of the diode. Moreover, the divergence of the observed current will cause steady state errors in the output voltage. In this paper, an optimal current observer is proposed. It achieves the highest observation accuracy by compensating for all the known parasitic parameters. By employing the optimal current observer-based predictive current controller, a buck converter is implemented. The converter has a convergently and accurately observed inductor current, and shows preferable transient response than the conventional voltage mode controlled converter. Besides, costs, power loss and size are minimized since the strategy requires no additional hardware for current sensing. The effectiveness of the proposed optimal current observer is demonstrated experimentally.

  15. High efficiency and low electromagnetic interference boost DC-DC converter

    Science.gov (United States)

    Yajun, Li; Xinquan, Lai; Qiang, Ye; Bing, Yuan

    2014-04-01

    A synchronous boost DC-DC converter with an adaptive dead time control (DTC) circuit and anti-ringing circuit is presented. The DTC circuit is used to provide adjustable dead time and zero inductor current detection for power transistors and therefore, a high efficiency is achieved by minimizing power losses, such as the shoot-through current loss, the body diode conduction loss, the charge-sharing loss and the reverse inductor current loss. Simultaneously, a novel anti-ringing circuit controlled by the switching sequence of power transistors is developed to suppress the ringing when the converter enters the discontinuous conduction mode (DCM) for low electromagnetic interference (EMI) and additional power savings. The proposed converter has been fabricated in a 0.6 μm CDMOS technology. Simulation and experimental results show that the power efficiency of the boost converter is above 81% under different load currents from 10 to 250 mA and a peak efficiency of 90% is achieved at about 100 mA. Moreover, the ringing is easily suppressed by the anti-ringing circuit and therefore the EMI noise is attenuated.

  16. Boost Full Bridge Bidirectional DC/DC Converter for Supervised Aeronautical Applications

    Directory of Open Access Journals (Sweden)

    Alberto Cavallo

    2014-01-01

    Full Text Available The More Electrical Aircraft concept requires electronic devices able to efficiently and safely convert electrical power between different voltage levels. The entire realization of a bidirectional DC/DC converter, from design to validation phase, is here discussed in detail. First, a boost full bridge electrical structure is selected, adopting a Parallel Input Parallel Output (PIPO interleaving technique and an optimal turns ratio selection for the transformers in order to reduce both weight and size of the equipment. Next, modulation schemes in both step-down and step-up modes are discussed. Successively ad hoc PI regulators for both operative modes are presented. A key idea of the paper is that the converter behavior must be related not only to the control strategy but also to a global supervision logic able to safely conduct the converter operations and to react from external stimuli. Thus, a finite state machine (FSM approach is employed. An innovative strategy called buffer mode is presented, defined as an intelligent combination of buck and boost modes. Extensive simulations and experimental results are shown, in order to confirm the effectiveness of the proposed approach.

  17. Dynamic modeling of DC-DC converters with peak current control in double-stage photovoltaic grid-connected inverters

    OpenAIRE

    Garcerá Sanfeliú, Gabriel; González Medina, Raul; Figueres Amorós, Emilio; Sandia Paredes, Jesús

    2012-01-01

    In photovoltaic (PV) double-stage grid-connected inverters a high-frequency DC-DC isolation and voltage step-up stage is commonly used between the panel and the grid-connected inverter. This paper is focused on the modeling and control design of DC-DC converters with Peak Current mode Control (PCC) and an external control loop of the PV panel voltage, which works following a voltage reference provided by a maximum power point tracking (MPPT) algorithm. In the proposed overall control structur...

  18. Influence of the snubbers and matching transformer on an optimal trajectory controlled resonant transistor DC/DC converter

    Directory of Open Access Journals (Sweden)

    Bankov Dimitrov Nikolay

    2012-01-01

    Full Text Available This work examines a series resonant DC/DC optimal trajectory controlled converter during operation above resonant frequency, taking into account the influence of the snubbers and matching transformer. We obtain expressions for the load characteristics, boundary curves between possible modes and limits of the soft commutation area. Computer simulation and experimental observation confirm the theoretical results.

  19. Influence of the snubbers and matching transformer on an optimal trajectory controlled resonant transistor DC/DC converter

    OpenAIRE

    Bankov Dimitrov Nikolay; Vuchev Stoyanov Aleksandar

    2012-01-01

    This work examines a series resonant DC/DC optimal trajectory controlled converter during operation above resonant frequency, taking into account the influence of the snubbers and matching transformer. We obtain expressions for the load characteristics, boundary curves between possible modes and limits of the soft commutation area. Computer simulation and experimental observation confirm the theoretical results.

  20. Quasi-Periodicity and Border-Collision Bifurcations in a DC-DC Converter with Pulsewidth Modulation

    DEFF Research Database (Denmark)

    Zhusubalaliyev, Zh. T.; Soukhoterin, E.A.; Mosekilde, Erik

    2003-01-01

    The paper considers the dynamics of a dc-dc converter with pulsewidth modulation. The typical scenario for the transition to chaos in such systems proceeds via quasi-periodicity, resonance cycles, and torus destruction. Detailed bifurcation analysis shows that the resonance solutions arise via...

  1. A Reconfigurable Series Resonant DC-DC Converter for Wide-Input and Wide-Output Voltages

    DEFF Research Database (Denmark)

    Shen, Yanfeng; Wang, Huai; Qin, Zian;

    2017-01-01

    This paper proposes a dual-bridge based LC series resonant dc-dc converter. The input inverter unit incorporates two bridge structures, i.e., a full-bridge inverter and a half-bridge inverter. For the output rectifier, it can be a full-bridge rectifier or an asymmetric half-bridge rectifier. Diff...

  2. Step-by-Step Design of an FPGA-Based Digital Compensator for DC/DC Converters Oriented to an Introductory Course

    Science.gov (United States)

    Zumel, P.; Fernandez, C.; Sanz, M.; Lazaro, A.; Barrado, A.

    2011-01-01

    In this paper, a short introductory course to introduce field-programmable gate array (FPGA)-based digital control of dc/dc switching power converters is presented. Digital control based on specific hardware has been at the leading edge of low-medium power dc/dc switching converters in recent years. Besides industry's interest in this topic, from…

  3. High-voltage boost quasi-Z-source isolated DC/DC converter

    DEFF Research Database (Denmark)

    Siwakoti, Yam P.; Blaabjerg, Frede; Loh, Poh Chiang;

    2014-01-01

    renewable energy systems, DC power supplies found in telecom, aerospace and electric vehicles. To demonstrate the performance of the proposed converter, a 400 V, 500 W prototype has been implemented in the laboratory. Efficiency of the prototype measured is found to vary from 89.0 to 97.4% when its input......A high-voltage gain two-switch quasi-Z-source isolated DC/DC converter has been presented in this study. It consists of a quasi-Z-source network at its input, a push-pull square-wave inverter at its middle, and a voltage-doubler rectifier at its output. When coordinated appropriately, the new...... converter uses less switches, a smaller common duty cycle and less turns for the transformer when compared with existing topologies. Its size and weight are therefore smaller, whereas its efficiency is higher. It is therefore well-suited for applications, where a wide range of voltage gain is required like...

  4. A digitally controlled PWM/PSM dual-mode DC/DC converter

    Institute of Scientific and Technical Information of China (English)

    Zhen Shaowei; Zhang Bo; Luo Ping; Hou Sijian; Ye Jingxin; Ma Xiao

    2011-01-01

    A digitally controlled pulse width modulation/pulse skip modulation (PWM/PSM) dual-mode buck DC/DC converter is proposed.Its operation mode can be automatically chosen as continuous conduction mode (CCM) or discontinuous conduction mode (DCM).The converter works in PSM at DCM and in 2 MHz PWM at CCM.Switching loss is reduced at a light load by skipping cycles.Thus high conversion efficiency is realized in a wide load current.The implementations of PWM control blocks,such as the ADC,the digital pulse width modulator (DPWM) and the loop compensator,and PSM control blocks are described in detail.The parameters of the loop compensator can be programmed for different external component values and switching frequencies,which is much more flexible than its analog rivals.The chip is manufactured in 0.13 μm CMOS technology and the chip area is 1.21 mm2.Experimental results show that the conversion efficiency is high,being 90% at 200 mA and 67% at 20 mA.Meanwhile,the measured load step response shows that the proposed dual-mode converter has good stability.

  5. A Monolithically Integrated 12V/5V Switch-Capacitor DC-DC Converter

    Institute of Scientific and Technical Information of China (English)

    耿莉; 陈治明; 刘先锋

    2000-01-01

    A monolithically integrated 12V/SV switch capacitor DC-DC converter with structure-simplified main circuit and control circuit is presented. Its topological circuit and basic operating principle are discussed in detail. It is shown that elevated operating frequency, increased capacitance and reduced turn-on voltage of the diodes can make the converter's output characteristics improved. Reducing resistance of the equivalent resistors and other parasitic parameters can make the operation frequency higher. As a feasible efficient method to fabricate monolithically integrated converter with high frequency and high output power, several basic circuits are parallelly combined where the serial-parallel capacitance is optimized for the maximum output power. The device selection and its fabrication method are presented. A feasible integration process and its corresponding layout are designed. All active devices including switching transistors and diodes are integrated together with all passive cells including capacitors and resistor on a single chip based on BiMOS process,as has been verified to be correct and practical by simulation and chip test.

  6. Lightweight DC-DC Converter with Partial Power Processing and MPPT for a Solar Powered Aircraft

    Science.gov (United States)

    Diab-Marzouk, Ahmad

    A lightweight dc-dc partial power processing converter is demonstrated for solar aerospace applications. A system-level model is conceived to determine conformity to payload and target distance objectives, with the Solarship aircraft used as an application example. The concept of partial power processing is utilized to realize a high efficiency lightweight converter that performs Max Peak Power Tracking (MPPT) to transfer power from the aircraft solar array to the high-voltage battery bus. The isolated Cuk is determined to be a suitable converter topology for the application. A small-signal model is derived for control design. The operation of a 400V, 2.7 kW prototype is verified at high frequency (200 kHz), high efficiency (> 98%), small mass (0.604 kg), and uses no electrolytic capacitors. MPPT operation is verified on a 376 V commercial solar installation at The University of Toronto. The prototype serves as an enabling technology for solar aerospace applications.

  7. A Protection Circuit for DC-DC Converter with Voltage Doubler

    Directory of Open Access Journals (Sweden)

    D.Elangovan

    2012-12-01

    Full Text Available This paper proposes a method to obtain a protected voltage gain by employing a protection circuit for the voltage doubler or multiplier circuit in an isolated tyde DC-DC Converter. The entire set up consists of a phase shift converter with a protected bridge/voltage doubler rectifier on the output side. The operating frequency of the phase shift converter is 20-25kHz (depending on the requirement of the application which is high enough to improve the efficiency. Ferrite core transformer is used in place of ordinary air core transformer, which is small in size with number of turns of the transformer is reduced and the overall power density is increased. The doubler circuit consists of electrolytic capacitors, which are rated at 400V in order to comply with IEC65 requirements. This paper proposes an “electrolytic capacitor protection circuit”, which enables the voltage rating of the electrolytics to be reduced to 250V. This circuit results in cost savings of more than 50% in the price of the electrolytic filter capacitors. The circuits were simulated using PSPICE SOFTWARE and the following results were obtained. For an input voltage of 200V, an output of 200V and400V were obtained in bridge mode and doubler mode respectively.

  8. Analysis and Controller Design of a Universal Bidirectional DC-DC Converter

    Directory of Open Access Journals (Sweden)

    Kou-Bin Liu

    2016-06-01

    Full Text Available In this paper, first the operating principles of a non-isolated universal bidirectional DC-DC converter are studied and analyzed. The presented power converter is capable of operating in all power transferring directions in buck/boost modes. Zero voltage switching can be achieved for all the power switches through proper modulation strategy design, therefore, the presented converter can achieve high efficiency. To further improve the efficiency, the relationship between the phase-shift angle and the overall system efficiency is analyzed in detail, an adaptive phase-shift (APS control method which determines the phase-shift value between gating signals according to the load level is then proposed. As the modulation strategy is a software-based solution, there is no requirement for additional circuits, therefore, it can be implemented easily and instability and noise susceptibility problems can be reduced. To validate the correctness and the effectiveness of the proposed method, a 300 W prototyping circuit is implemented and tested. A low cost dsPIC33FJ16GS502 digital signal controller is adopted in this paper to realize the power flow control, DC-bus voltage regulation and APS control. According to the experimental results, a 12.2% efficiency improvement at light load and 4.0% efficiency improvement at half load can be achieved.

  9. High reliability DC/DC converter module for electronic boards equipped with FPGAs

    Science.gov (United States)

    Viganò, W.; Boccardi, A.; Zamantzas, C.

    2015-01-01

    The Beam Instrumentation Group at CERN is designing a new general-purpose VME carrier module utilising several PTH04T230W DC/DC converters. These off-the-shelf converters are built with unshielded inductors and need to be mounted on the printed circuit board as stand-alone components. Thus, reducing the global manageability and increasing the total cost of the carrier module. The new design aims to develop a module with better power dissipation, efficiency and reliability. In the future, it should be also possible to be directly integrated on the mainboard. For this reason, a Buck DC/DC converter has been implemented with the following main characteristics: input range from 3.0 V to 5.5 V; output range from 0.6 V to 3.3 V, settable by means of an external resistor; output current protection at 6 A; maximum output ripple ± 50 mVpp; switching frequency of 300KHz; short circuit protection; On/Off function; EMI reduction with frequency spread spectrum; soft-start function and thermal shutdown, in a 16 × 19 mm compact size. The selected buck controller is the TPS40303 integrated circuit and drives the CSD16321 power MOSFET, both from Texas Instruments. All selected components have been used at a minimum derating of 50% to reduce component stress and increase the reliability of this module. The selected inductors, i.e. Bourns SRP1055, are the main contributor for the high efficiency (95%), due to their very low equivalent series resistance. On the 4-layer PCB comprising all the components of this module, a snubber circuit, for further reduction of the output ripple due to the MOSFET ringing, can be mounted optionally. It is left as an option due to its effect on the total efficiency. The board layout has been optimized for maximum heat transfer and it can be used without active cooling. The board can maintain the maximum temperature on its surface, while at maximum current output, below 55°C at 25°C ambient temperature. An example of the electrical performance

  10. An Integrated Multifunctional Bidirectional AC/DC and DC/DC Converter for Electric Vehicles Applications

    Directory of Open Access Journals (Sweden)

    Liwen Pan

    2016-06-01

    Full Text Available This paper presents an on-board vehicular battery charger that integrates bidirectional AC/DC converter and DC/DC converter to achieve high power density for application in electric vehicles (EVs. The integrated charger is able to transfer electrical energy between the battery pack and the electric traction system and to function as an AC/DC battery charger. The integrated charger topology is presented and the design of passive components is discussed. The control schemes are developed for motor drive system and battery-charging system with a power pulsation reduction circuit. Simulation results in MATLAB/Simulink and experiments on a 30-kW motor drive and 3.3-kW AC/DC charging prototype validate the performance of the proposed technology. In addition, power losses, efficiency comparison and thermal stress for the integrated charger are illustrated. The results of the analyses show the validity of the advanced integrated charger for electric vehicles.

  11. Multiphase High-Frequency Isolated DC-DC Converter for Industrial Applications

    Science.gov (United States)

    Maurya, Rakesh; Srivastava, S. P.; Agarwal, Pramod

    2014-01-01

    Industrial applications such as welding, plasma cutting, and surface hardening require a large DC current at low voltage. In such applications, the rating of power supply varies from few kilowatts to hundreds of kilowatts. The power supply employs in such applications particularly in arc welding process is expected to operate from open-circuit (no-load) to short-circuit (when the electrode sticks to the workpiece for a short span of time) quickly. In this paper, high-frequency isolated multiphase DC-DC converter is proposed which is well suited for aforementioned applications. Based on mathematical analysis, a simulation study with 5 kW, 5 V/1,000 A proposed model is carried out using Simulink block set and Sim Power System tool box and its performances are evaluated under symmetrical control methods. To verify the simulation results, scaled prototype model of rating 1.5 V/100 A is developed and tested with aforementioned control method under different operating conditions. In comparison with conventional welding power supply employed in many industries, the performance of proposed converter is improved significantly in terms of size and weight, efficiency and dynamic response.

  12. Bifurcation Analysis of a DC-DC Bidirectional Power Converter Operating with Constant Power Loads

    Science.gov (United States)

    Cristiano, Rony; Pagano, Daniel J.; Benadero, Luis; Ponce, Enrique

    Direct current (DC) microgrids (MGs) are an emergent option to satisfy new demands for power quality and integration of renewable resources in electrical distribution systems. This work addresses the large-signal stability analysis of a DC-DC bidirectional converter (DBC) connected to a storage device in an islanding MG. This converter is responsible for controlling the balance of power (load demand and generation) under constant power loads (CPLs). In order to control the DC bus voltage through a DBC, we propose a robust sliding mode control (SMC) based on a washout filter. Dynamical systems techniques are exploited to assess the quality of this switching control strategy. In this sense, a bifurcation analysis is performed to study the nonlinear stability of a reduced model of this system. The appearance of different bifurcations when load parameters and control gains are changed is studied in detail. In the specific case of Teixeira Singularity (TS) bifurcation, some experimental results are provided, confirming the mathematical predictions. Both a deeper insight in the dynamic behavior of the controlled system and valuable design criteria are obtained.

  13. Adaptive terminal sliding-mode control strategy for DC-DC buck converters.

    Science.gov (United States)

    Komurcugil, Hasan

    2012-11-01

    This paper presents an adaptive terminal sliding mode control (ATSMC) strategy for DC-DC buck converters. The idea behind this strategy is to use the terminal sliding mode control (TSMC) approach to assure finite time convergence of the output voltage error to the equilibrium point and integrate an adaptive law to the TSMC strategy so as to achieve a dynamic sliding line during the load variations. In addition, the influence of the controller parameters on the performance of closed-loop system is investigated. It is observed that the start up response of the output voltage becomes faster with increasing value of the fractional power used in the sliding function. On the other hand, the transient response of the output voltage, caused by the step change in the load, becomes faster with decreasing the value of the fractional power. Therefore, the value of fractional power is to be chosen to make a compromise between start up and transient responses of the converter. Performance of the proposed ATSMC strategy has been tested through computer simulations and experiments. The simulation results of the proposed ATSMC strategy are compared with the conventional SMC and TSMC strategies. It is shown that the ATSMC exhibits a considerable improvement in terms of a faster output voltage response during load changes.

  14. Progress on DC-DC Converters for a Silicon Tracker for the sLHC Upgrade

    CERN Document Server

    Dhawan, S; Chen, H; Khanna, R; Kierstead, J; Lanni, F; Lynn, D; Musso, C; Rescia, S; Smith, H; Tipton, P; M. Weber, M

    2009-01-01

    There is a need for DC-DC converters which can operate in the extremely harsh environment of the sLHC Si Tracker. The environment requires radiation qualification to a total ionizing radiation dose of 50 Mrad and a displacement damage fluence of 5 x 1014 /cm2 of 1 MeV equivalent neutrons. In addition a static magnetic field of 2 Tesla or greater prevents the use of any magnetic components or materials. In February 2007 an Enpirion EN5360 was qualified for the sLHC radiation dosage but the converter has an input voltage limited to a maximum of 5.5V. From a systems point of view this input voltage was not sufficient for the application. Commercial LDMOS FETs have developed using a 0.25 μm process which provided a 12 volt input and were still radiation hard. These results are reported here and in previous papers. Plug in power cards with ×10 voltage ratio are being developed for testing the hybrids with ABCN chips. These plug-in cards have air coils but use commercial chips that are not designed to be radiatio...

  15. Fast response double series resonant high-voltage DC-DC converter

    Science.gov (United States)

    Lee, S. S.; Iqbal, S.; Kamarol, M.

    2012-10-01

    In this paper, a novel double series resonant high-voltage dc-dc converter with dual-mode pulse frequency modulation (PFM) control scheme is proposed. The proposed topology consists of two series resonant tanks and hence two resonant currents flow in each switching period. Moreover, it consists of two high-voltage transformer with the leakage inductances are absorbed as resonant inductor in the series resonant tanks. The secondary output of both transformers are rectified and mixed before supplying to load. In the resonant mode operation, the series resonant tanks are energized alternately by controlling two Insulated Gate Bipolar Transistor (IGBT) switches with pulse frequency modulation (PFM). This topology operates in discontinuous conduction mode (DCM) with all IGBT switches operating in zero current switching (ZCS) condition and hence no switching loss occurs. To achieve fast rise in output voltage, a dual-mode PFM control during start-up of the converter is proposed. In this operation, the inverter is started at a high switching frequency and as the output voltage reaches 90% of the target value, the switching frequency is reduced to a value which corresponds to the target output voltage. This can effectively reduce the rise time of the output voltage and prevent overshoot. Experimental results collected from a 100-W laboratory prototype are presented to verify the effectiveness of the proposed system.

  16. Design, optimization and new solutions for DC/DC converters in hybrid vehicles; Design, Optimierung und neue Loesungen fuer DC/DC-Wandler in Hybridfahrzeugen

    Energy Technology Data Exchange (ETDEWEB)

    Pledl, Georg; Lutter, Peter [Finepower GmbH, Ismaning (Germany)

    2010-07-01

    Especially in automotive engineering, the big aim of electronic device development is to combine minimum possible weight, highest efficiency and low electromagnetic interference. Since there is a wide range of energy storage devices and power consumption requirements are very versatile, there are many possible solutions for electronic power devices, but not all of them will be appropriate for each system. One possible solution concerning dc/dc converters is represented by the phase shift operation for full bridge topologies. This procedure is used for supplying the electrical 14 V system from the high voltage energy storage or, in the other direction, charge the HV battery from the 14 V net or even from an external 230 V / 400 ac net. Finepower has developed 2 prototypes for research, which are presented in this contribution. Another new topology, a bidirectional LLC Converter, is presented as well. Energy consumption is growing and the available space for electronic power devices is held very small, so the power density increases and thermal management becomes more difficult. As dimensions of bus bars, semiconductors or inductive components are shrinking, parasitic influence becomes more and more significant. For getting information about function and influence of parasitics of electronic power devices, simulation is a very important tool since it saves much time and gives the possibility to extract internal dimensions of electrical circuits which cannot be measured in reality. (orig.)

  17. High Output Voltage Based Multiphase Step-Up DC-DC Converter Topology with Voltage Doubler Rectifiers

    Directory of Open Access Journals (Sweden)

    Liao Xiaozhong

    2013-02-01

    Full Text Available High Output Voltage Based Multiphase Step-Up DC-DC Converter topology with voltage doubler rectifiers is presented in this paper. High output voltage is obtained due to the series combination of voltage doubler rectifiers on the secondary side of high frequency transformers. This topology is useful in the application where the output voltage is greater than the input. The two loop control strategy has been developed in order to analyze the stable and effective working of the converter topology. Therefore the working mode analysis of the converter topology has been described in detail. The multiphase step-up DC-DC converter topology is first simulated on MATLAB and then a prototype has been designed in order to verify the simulation and experimental results. Finally the simulation and experimental results are found to be satisfactory.

  18. DIAGNOSTIC/PROGNOSTIC EXPERIMENTS FOR CAPACITOR DEGRADATION AND HEALTH MONITORING IN DC-DC CONVERTERS

    Data.gov (United States)

    National Aeronautics and Space Administration — Studying and analyzing the ageing mechanisms of electronic components avionics in systems such as the GPS and INAV are of critical importance. In DC-DC power...

  19. Digitally intensive DC-DC converter for extreme space environments Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Space Micro –Arizona State University (ASU) team will develop an all-digitally controlled, wide temperature range point-of-load switch-mode DC-DC regulator...

  20. Digitally intensive DC-DC converter for extreme space environments Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Space Micro-Arizona State University (ASU) team will develop an all-digitally controlled, wide temperature range point-of-load switch-mode DC-DC regulator core...

  1. A 1.6-kW, 110-kHz dc-dc converter optimized for IGBT's

    Science.gov (United States)

    Chen, Keming; Stuart, Thomas A.

    1993-01-01

    A full bridge dc-dc converter using a zero-current and zero-voltage switching technique is described. This circuit utilizes the characteristics of the IGBT to achieve power and frequency combinations that are much higher than previously reported for this device. Experimental results are included for a 1.6-kW, 110-kHz converter with 95 percent efficiency.

  2. An Interleaved Reduced-Component-Count Multivoltage Bus DC/DC Converter for Fuel Cell Powered Electric Vehicle Applications

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Lixin [ORNL; Su, Gui-Jia [ORNL

    2008-01-01

    An interleaved reduced-component-count dc/dc converter is proposed for power management in fuel cell powered vehicles with a multivoltage electric net. The converter is based on a simplified topology and can handle more power with less ripple current, therefore reducing the capacitor requirements, making it more suited for fuel cell powered vehicles in the near future. A prototype rated at 4.3 kW was built and tested to verify the proposed topology.

  3. A new approach to improve dynamic characteristics of digitally controlled buck-boost dc-dc converter

    OpenAIRE

    2010-01-01

    This paper presents a new digital control buck-boost dc-dc converter with bias model to improve dynamic characteristics. The buck-boost converter needs to respond appropriately to changing input voltage and load change with wide input voltage. This approach makes adjustment to the bias value by input voltage and output current. As a result, it is revealed that not only the dynamic characteristics but also static characteristics can be improved and it is effective for wide range input voltage.

  4. Design of piezoelectric transformer for DC/DC converter with stochastic optimization method

    Science.gov (United States)

    Vasic, Dejan; Vido, Lionel

    2016-04-01

    Piezoelectric transformers were adopted in recent year due to their many inherent advantages such as safety, no EMI problem, low housing profile, and high power density, etc. The characteristics of the piezoelectric transformers are well known when the load impedance is a pure resistor. However, when piezoelectric transformers are used in AC/DC or DC/DC converters, there are non-linear electronic circuits connected before and after the transformer. Consequently, the output load is variable and due to the output capacitance of the transformer the optimal working point change. This paper starts from modeling a piezoelectric transformer connected to a full wave rectifier in order to discuss the design constraints and configuration of the transformer. The optimization method adopted here use the MOPSO algorithm (Multiple Objective Particle Swarm Optimization). We start with the formulation of the objective function and constraints; then the results give different sizes of the transformer and the characteristics. In other word, this method is looking for a best size of the transformer for optimal efficiency condition that is suitable for variable load. Furthermore, the size and the efficiency are found to be a trade-off. This paper proposes the completed design procedure to find the minimum size of PT in need. The completed design procedure is discussed by a given specification. The PT derived from the proposed design procedure can guarantee both good efficiency and enough range for load variation.

  5. Evaluating neural control with optimal architecture for DC/DC converter

    Directory of Open Access Journals (Sweden)

    Fredy Hernán Martínez Sarmiento

    2010-05-01

    -power equipment raises great design challenges due to the mathematical model’s complexity and its highly nonlinear dynamic characteristics. Artificial intelligence techniques, such as neuronal networks, suppose great improvements in design and final per- formance, given their capacity for learning complex dynamics and generalising their behaviour. This work was aimed at propo- sing (and evaluating dynamic response later on direct control link with neuronal networks which also allowed eliminating test ele- ments and error in its design. Artificial neuronal network-based direct control was designed as well as possible using bio-inspired search models. This simultaneously optimised two different but fundamental aspects of the network: architecture and the weight of the connections. The control was applied to a boost converter. The results led to observing the scheme’s dynamic performan- ce; response time and exit voltage delta led to concluding that the criteria selected for designing the control were appropriate and represented a contribution towards developing control applications of DC/DC switchmode systems.

  6. A Low-Power Asynchronous Step-Down DC-DC Converter for Implantable Devices.

    Science.gov (United States)

    Al-Terkawi Hasib, Omar; Sawan, M; Savaria, Y

    2011-06-01

    In this paper, we present a fully integrated asynchronous step-down switched capacitor dc-dc conversion structure suitable for supporting ultra-low-power circuits commonly found in biomedical implants. The proposed converter uses a fully digital asynchronous state machine as the heart of the control circuitry to generate the drive signals. To minimize the switching losses, the asynchronous controller scales the switching frequency of the drive signals according to the loading conditions. It also turns on additional parallel switches when needed and has a backup synchronous drive mode. This circuit regulates load voltages from 300 mV to 1.1 V derived from a 1.2-V input voltage. A total of 350 pF on-chip capacitance was implemented to support a maximum of 230-μ W load power, while providing efficiency up to 80%. The circuit validating the proposed concepts was fabricated in 0.13- μm complementary metal-oxide semiconductor technology. Experimental test results confirm the expected functionality and performance of the proposed circuit.

  7. A Multiphase, Modular, Bidirectional, Triple-Voltage DC-DC Converter Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Su, Gui-Jia [ORNL; Tang, Lixin [ORNL

    2008-01-01

    Electrical power systems in future hybrid and fuel cell vehicles may employ three voltage [14 V, 42 V, and high voltage (HV)] nets. These will be necessary to accommodate existing 14-V loads as well as efficiently handle new heavy loads at the 42-V net and a traction drive on the HV bus. A low-cost DC-DC converter was proposed for connecting the three voltage nets. It minimizes the number of switches and their associated gate driver components by using two half-bridges and a high-frequency transformer. Another salient feature is that the half bridge on the 42-V bus is also utilized to provide the 14-V bus by operating at duty ratios around an atypical value of 1/3. Moreover, it makes use of the parasitic capacitance of the switches and the transformer leakage inductance for soft switching. The use of half bridges makes the topology well suited for interleaved multiphase modular configurations as a means to increase the power level because the capacitor legs can be shared. This paper presents simulation and experimental results on an interleaved two-phase arrangement rated at 4.5 kW. Also discussed are the benefits of operating with an atypical duty ratio on the transformer and a preferred multiphase configuration to minimize capacitor ripple currents.

  8. Closed loop control of ZVS half bridge DC-DC converter with DCS PWM Control

    Directory of Open Access Journals (Sweden)

    JANAPATI SIVAVARA PRASAD

    2012-10-01

    Full Text Available

    The main drawback of the conventional symmetric control is that both primary switches in the converter operate at hard switching condition. Moreover, during the off-time period of two switches, the oscillation between the transformer leakage inductance and junction capacitance of the switches results in energy dissipation and electromagnetic interference (EMI emissions due to reverse recovery of MOSFETs body diodes. The asymmetric (complementary control was proposed to achieve ZVS operation for HB switches. However, asymmetric stresses distribution on the corresponding components may occur due to the asymmetric duty cycle distribution for the two primary switches. A new control scheme, to be known as duty-cycle shifted PWM (DCS PWM control, is proposed and applied to the conventional HB dc–dc converters to achieve ZVS for both the  switches without adding extra components and without adding asymmetric penalties of the complementary control. The concept of this new control scheme is shifting one of the two symmetric PWM driving signals close to the other, such that ZVS may be achieved for the lagging switch due to the shortened resonant interval. Moreover, based on the DCS PWM control, a new half-bridge topology is proposed to achieve ZVS for both the main switches and auxiliary switch by adding an auxiliary switch and diode in the proposed half bridge. ZVS for the  switch is achieved by utilizing the energy trapped in the leakage inductance. There are two control schemes. One is open loop and the other is closed loop. In open loop scheme, the given dc-dc converter is operating under disturbance. This disturbance effect is eliminated in closed loop scheme.

     

  9. Analysis, simulation and experimental study of chaotic behaviour in parallel-connected DC-DC boost converters

    Energy Technology Data Exchange (ETDEWEB)

    Natsheh, Ammar N.; Kettleborough, J. Gordon [Department of Electronic and Electrical Engineering, Loughborough University, Loughborough, Leicestershire LE11 3TU (United Kingdom); Nazzal, Jamal M. [Faculty of Engineering, Al-Ahliyya Amman University, Post Code 19328 Amman (Jordan)], E-mail: jnazzal@ammanu.edu.jo

    2009-03-15

    The paper describes an experimental study of the bifurcation behaviour of a modular peak current-mode controlled DC-DC boost converter. The parallel-input/parallel-output converter comprises two identical boost circuits and operates in the continuous-current conduction mode. A comparison is made between the results obtained from an experimental converter with those obtained from bifurcation diagrams generated from previous work and waveforms from a new MATLAB/SIMULINK simulation presented in this paper. Another comparison is made between the modular converter diagrams with those of the single boost converter.

  10. Performance and scalability of isolated DC-DC converter topologies in low voltage, high current applications

    Energy Technology Data Exchange (ETDEWEB)

    Vaisanen, V.

    2012-07-01

    Fuel cells are a promising alternative for clean and efficient energy production. A fuel cell is probably the most demanding of all distributed generation power sources. It resembles a solar cell in many ways, but sets strict limits to current ripple, common mode voltages and load variations. The typically low output voltage from the fuel cell stack needs to be boosted to a higher voltage level for grid interfacing. Due to the high electrical efficiency of the fuel cell, there is a need for high efficiency power converters, and in the case of low voltage, high current and galvanic isolation, the implementation of such converters is not a trivial task. This thesis presents galvanically isolated DC-DC converter topologies that have favorable characteristics for fuel cell usage and reviews the topologies from the viewpoint of electrical efficiency and cost efficiency. The focus is on evaluating the design issues when considering a single converter module having large current stresses. The dominating loss mechanism in low voltage, high current applications is conduction losses. In the case of MOSFETs, the conduction losses can be efficiently reduced by paralleling, but in the case of diodes, the effectiveness of paralleling depends strongly on the semiconductor material, diode parameters and output configuration. The transformer winding losses can be a major source of losses if the windings are not optimized according to the topology and the operating conditions. Transformer prototyping can be expensive and time consuming, and thus it is preferable to utilize various calculation methods during the design process in order to evaluate the performance of the transformer. This thesis reviews calculation methods for solid wire, litz wire and copper foil winding losses, and in order to evaluate the applicability of the methods, the calculations are compared against measurements and FEM simulations. By selecting a proper calculation method for each winding type, the winding

  11. Energy Conversion Module (ECM) - DC/DC converter with integrated supercaps

    Energy Technology Data Exchange (ETDEWEB)

    Ollhaeuser, Helmut [ALCOA/AFL Europe GmbH (Germany)

    2008-07-01

    In the light of increasing hybridization of future vehicle generations mainly those functionalities will be realized which contribute to fuel- and at the end emission-reduction. Recuperation, Start-Stop, E-steering and EDS-stabilization therefore constitute applications for which an efficient energy management has to be provided In this context ALCOA / AFL Europe GmbH developed a patent pending system solution, by which in one single unit a powerful DC/DC converter is integrated with the storage medium EDLC or Super-/Ultracap - on the one hand the restrictive packaging and on the other hand high performance requirements of the OEM can be met in a high degree. Possible issues arising from the compact integration of the supercaps such as heat dissipation and EMI are solved in a unique way - even the impacts in case of a defect cell are eliminated by a sophisticated balancing. The main performance characteristics of the current finished 1 KW solution being in test operation at various OEM are: - Output: 1 KW bidirectional - Capacity: 29,8 F / 12 Cells a 350 F - Additional fused power output - Optional output for consumers during motor start - Protection class IP 6K7 - Buck/Boost converter 2-phases - Operating frequency 125 kHz - Current control and phase monitoring realized in HW With its scaleable approach and the possibility to be integrated rapidly and cost-efficient in new carlines, the ECM just today combines the advantages of an intelligent electric power management. New prospective application-ranges - i.e. up to 5 KW for commercial vehicles and/or buses - are right now under development and clear its way for series implementation, soon. (orig.)

  12. A fast novel soft-start circuit for peak current-mode DC-DC buck converters

    Institute of Scientific and Technical Information of China (English)

    Li Jie; Yang Miao; Sun Weifeng; Lu Xiaoxia; Xu Shen; Lu Shengli

    2013-01-01

    A fully integrated soft-start circuit for DC-DC buck converters is presented.The proposed high speed soft-start circuit is made of two sections:an overshoot suppression circuit and an inrush current suppression circuit.The overshoot suppression circuit is presented to control the input of the error amplifier to make output voltage limit increase in steps without using an external capacitor.A variable clock signal is adopted in the inrush current suppression circuit to increase the duty cycle of the system and suppress the inrush current.The DC-DC converter with the proposed soft-start circuit has been fabricated with a standard 0.13 μm CMOS process.Experimental results show that the proposed high speed soft-start circuit has achieved less than 50 μs start-up time.The inductor current and the output voltage increase smoothly over the whole load range.

  13. Integrated modeling and control of a PEM fuel cell power system with a PWM DC/DC converter

    Energy Technology Data Exchange (ETDEWEB)

    Choe, Song-Yul; Ahn, Jong-Woo [Mechanical Engineering Department, Auburn University, Auburn, AL 36848 (United States); Lee, Jung-Gi [Electrical Engineering Department, Pohang University of Science and Technology, Pohang (Korea); Baek, Soo-Hyun [Electrical Engineering Department, Dong-guk University, Seoul (Korea)

    2007-02-10

    A fuel cell powered system is regarded as a high current and low voltage source. To boost the output voltage of a fuel cell, a DC/DC converter is employed. Since these two systems show different dynamics, they need to be coordinated to meet the demand of a load. This paper proposes models for the two systems with associated controls, which take into account a PEM fuel cell stack with air supply and thermal systems, and a PWM DC/DC converter. The integrated simulation facilitates optimization of the power control strategy, and analyses of interrelated effects between the electric load and the temperature of cell components. In addition, the results show that the proposed power control can coordinate the two sources with improved dynamics and efficiency at a given dynamic load. (author)

  14. A Feed-Forward Control Realizing Fast Response for Three-Branch Interleaved DC-DC Converter in DC Microgrid

    Directory of Open Access Journals (Sweden)

    Haojie Wang

    2016-07-01

    Full Text Available It is a common practice for storage batteries to be connected to DC microgrid buses through DC-DC converters for voltage support on islanded operation mode. A feed-forward control based dual-loop constant voltage PI control for three-branch interleaved DC-DC converters (TIDC is proposed for storage batteries in DC microgrids. The working principle of TIDC is analyzed, and the factors influencing the response rate based on the dual-loop constant voltage control for TIDC are discussed, and then the method of feed-forward control for TIDC is studied to improve the response rate for load changing. A prototype of the TIDC is developed and an experimental platform is built. The experiment results show that DC bus voltage sags or swells caused by load changing can be reduced and the time for voltage recovery can be decreased significantly with the proposed feed-forward control.

  15. Design and Implementation of Anti-windup PI Control on DC-DC Bidirectional Converter for Hybrid Vehicle Applications

    Directory of Open Access Journals (Sweden)

    Muh. Zakiyullah Romdlony

    2012-07-01

    Full Text Available Well-regulated DC bus voltage is the important point to guarantee the power demand in hybrid vehicle applications. Voltage regulation can be achieved with control method that build switching signal on DC-DC converter. This paper describes design and small scale experimental results of bus voltage regulation control of the DC-DC bidirectional converter with battery and supercapacitor as energy source. The control system consists of two control loops, the outer loop that get DC bus voltage feedback using PI anti-windup back calculation control method. This outer loop will generate a reference current for the inner loop that implement hysteresis control. The inner control loop will compare that reference curent with the source current obtained from the current sensor. Simulation and experimental results show that bus voltage is well-regulated under the load changes with 1% voltage ripple.

  16. Discrete time domain modelling and analysis of dc-dc converters with continuous and discontinuous inductor current

    Science.gov (United States)

    Iwens, R. P.; Lee, F. C.; Triner, J. E.

    1977-01-01

    Using discrete time state variable representation, a generalized computer-aided modeling and analysis of dc-dc converters is presented. The methodology provides exact modeling and is applicable to all types of power stages and duty-cycle control, including continuous and discontinuous inductor current operation. Converter stability, transient behavior and audio susceptibility can be analytically evaluated and predicted. The generalized theory of the proposed approach to converter modeling and analysis is presented first, followed by a demonstrative example applying the theory to a constant frequency buck converter operating in continuous and discontinuous inductor current mode. Excellent agreement with laboratory test data has been observed.

  17. Family of Step-up DC/DC Converters with Fast Dynamic Response for Low Power Applications

    DEFF Research Database (Denmark)

    N. Soltani, Mohsen; Mostaan, Ali; Siwakoti, Yam Prasad

    2016-01-01

    This study presents a family of novel step-up DC/DC converters which do not have a right half plane zero in their transfer function resulting in faster dynamic behaviour of the converters under the load variation. In addition, the voltage stress on all the active switches and diodes is as low...... is presence of only two switches in the basic converter and its derivatives. The dynamic performance of the proposed converter and its first derivative is analysed by small-signal model using the state-space averaging method. The theoretical model is verified by experiments using GaN high...

  18. A brief review of models of DC-DC power electronic converters for analysis of their stability

    Science.gov (United States)

    Siewniak, Piotr; Grzesik, Bogusław

    2014-10-01

    A brief review of models of DC-DC power electronic converters (PECs) is presented in this paper. It contains the most popular, continuous-time and discrete-time models used for PEC simulation, design, stability analysis and other applications. Both large-signal and small-signal models are considered. Special attention is paid to models that are used in practice for the analysis of the global and local stability of PECs.

  19. An improved resonant parametric perturbation for chaos control with applications to control of DC/DC converters

    Institute of Scientific and Technical Information of China (English)

    Zhou Yu-Fei(周宇飞); Tse C K; Qiu Shui-Sheng(丘水生); Chen Jun-Ning(陈军宁)

    2005-01-01

    This paper presents an improved resonant parametric perturbation method based on the modulation of a nonlinear map for controlling chaos. The control target can be any periodic orbit, which is not necessarily what is embedded in the chaotic attractor. Application of the method is illustrated for a common current-programmed DC/DC converter which has been known to easily become chaotic for a wide parameter range. The control effects of chaos are demonstrated with computer simulations.

  20. DC motor operation controlled from a DC/DC power converter in pulse mode with low duty cycle

    OpenAIRE

    Stefanov, Goce; Kukuseva, Maja; Citkuseva Dimitrovska, Biljana

    2016-01-01

    In this paper pulse mode of operation of DC motor controlled by DC/DC power converter is analyzed. DC motor operation with time intervals in which the motor operates without output load is of interest. In this mode it is possible the motor to restore energy. Also, in the paper are represented calculations for the amount of the restored energy in the pulse mode operation of the motor for different duty cycles.

  1. Hierarchical Velocity Control Based on Differential Flatness for a DC/DC Buck Converter-DC Motor System

    Directory of Open Access Journals (Sweden)

    R. Silva-Ortigoza

    2014-01-01

    Full Text Available This paper presents a hierarchical controller that carries out the angular velocity trajectory tracking task for a DC motor driven by a DC/DC Buck converter. The high level control is related to the DC motor and the low level control is dedicated to the DC/DC Buck converter; both controls are designed via differential flatness. The high level control provides a desired voltage profile for the DC motor to achieve the tracking of a desired angular velocity trajectory. Then, a low level control is designed to ensure that the output voltage of the DC/DC Buck converter tracks the voltage profile imposed by the high level control. In order to experimentally verify the hierarchical controller performance, a DS1104 electronic board from dSPACE and Matlab-Simulink are used. The switched implementation of the hierarchical average controller is accomplished by means of pulse width modulation. Experimental results of the hierarchical controller for the velocity trajectory tracking task show good performance and robustness against the uncertainties associated with different system parameters.

  2. Quasi-Periodicity, Chaos and Coexistence in the Time Delay Controlled Two-Cell DC-DC Buck Converter

    Science.gov (United States)

    Koubaâ, Karama; Feki, Moez

    In addition to border collision bifurcation, the time delay controlled two-cell DC/DC buck converter is shown to exhibit a chaotic behavior as well. The time delay controller adds new design parameters to the system and therefore the variation of a parameter may lead to different types of bifurcation. In this work, we present a thorough analysis of different scenarios leading to bifurcation and chaos. We show that the time delay controlled two-cell DC/DC buck converter may also exhibit a Neimark-Sacker bifurcation which for some parameter set may lead to a 2D torus that may then break yielding a chaotic behavior. Besides, the saturation of the controller can also lead to the coexistence of a stable focus and a chaotic attractor. The results are presented using numerical simulation of a discrete map of the two-cell DC/DC buck converter obtained by expressing successive crossings of Poincaré section in terms of each other.

  3. Gate Driver Circuit of Power Electronic Switches with Reduced Number of Isolated DC/DC Converter for a Switched Reluctance Motor

    OpenAIRE

    Ali Asghar Memon; Imtiaz Hussain; Muhammad Aslam Uqaili

    2013-01-01

    This paper presents a gate driver circuit for the switching devices used in the asymmetrical converter for a switched reluctance machine with reduced number of isolated dc/dc converters. Isolation required in the gate driver circuit of switching devices is indispensable. For the purpose of isolation different arrangements may be used such as pulse transformers. The dc/dc converter for isolation and powering the gate drive circuits is suitable, cheaper in cost and simple to implement. It is al...

  4. Control and dynamic analysis of a parallel-connected single active bridge DC-DC converter for DC-grid wind farm application

    DEFF Research Database (Denmark)

    Park, Kiwoo; Chen, Zhe

    2015-01-01

    This study presents a control strategy and its dynamic analysis of a high-power dc-dc converter, which is constructed with the parallel-connected single active bridge (SAB) dc-dc converters for dc-grid wind farm applications. The structural and operational characteristics of the SAB dc-dc converter...... have several advantages for high-power applications, and the modular concept of the parallel-connected converter is highly beneficial especially for offshore wind farm applications in terms of maintenance cost and fault tolerance. To justify the feasibility of the parallel-connected SAB dc-dc converter...... for dc-grid wind farm applications, an input voltage control method based on the PI control will be introduced and the dynamics of the overall system will be analysed. The analysis results are to be verified by means of simulations and experiments....

  5. Performance evaluation of Maximum Power Point Tracking algorithm with buck dc-dc converter for Solar PV system

    Directory of Open Access Journals (Sweden)

    Ahteshamul Haque

    2016-02-01

    Full Text Available The energy crisis concern leads to look for alternate source of energy. Solar energy is considered as most reliable among the all renewable energy sources. Solar PV (Photovoltaic is used to convert solar energy into electric energy. The efficiency of solar PV is very low and its characteristic is nonlinear. To overcome these drawbacks a technique known as maximum power point tracking is used. This algorithm is implemented in the control circuit of DC – DC converter. The objective of this paper is to evaluate the MPPT (Maximum Power Point Tracking with buck DC-DC converter under load varying conditions. The simulation work is done using PSIM simulation software.

  6. A Novel Dual-input Isolated Current-Fed DC-DC Converter for Renewable Energy System

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2010-01-01

    In this paper, a novel isolated current-fed DC-DC converter (boost-type) with two input power sources based on multi-transformer structure, which is suitable for fuel cells and super-capacitors hybrid energy system, is proposed and designed. With particular transformer windings connection strategy....... Furthermore, the method to increase the number of input ports, the magnetic integration structure, and ground loop decoupling are discussed. Experimental results from the lab prototype converter with two DC voltage sources verify the validity of the theoretical analysis and design of the converter....

  7. Multi-output DC-DC converters based on diode-clamped converters configuration

    DEFF Research Database (Denmark)

    Nami, A.; Zare, F.; Ghosh, A.;

    2010-01-01

    for a diode-clamed inverter in the grid connection systems, where boosting low rectified output-voltage and series DC link capacitors is required. To verify the proposed topology, steady-state and dynamic analyses of a MOB converter are examined. A simple control strategy has been proposed to demonstrate...... the performance of the proposed topology for a double-output boost converter. The topology and its control strategy can easily be extended to offer multiple outputs. Simulation and experimental results are presented to show the validity of the control strategy for the proposed converter....

  8. DC-DC boost-flyback converter functioning as input stage for one phase low power grid-connected inverter

    Directory of Open Access Journals (Sweden)

    Kawa Adam

    2014-09-01

    Full Text Available The paper treats about main problems of one phase DC-AC microinverters that allow single solar cell to be joined with the grid. One of the issues is to achieve high voltage gain with high efficiency in DC circuit, which is necessary for proper operation of inverter. The operating principles, results of practical implementation and investigations on boost-flyback converter, which meets mentioned demands, are presented. (high step-up DC-DC boost-flyback converter for single phase grid microinverter

  9. Analysis and Improvement of a Passivity-Based Controller for DC-DC Boost Converters with Inductor Resistance

    Science.gov (United States)

    Son, Young Ik

    Output voltage regulation problem of DC-DC boost power converters is studied based on an averaged model with a practical inductor. This paper exploits the effect of inductor's parasitic resistance on the performance of an existing parallel-damped (PD) passivity-based controller (PBC) under load variations. As an attempt to apply the passivity-based framework to the converter with parasitic resistance we have combined a new proportional-integral (PI) controller with the PBC. Simulation results show that the combined (PBC and PI) dynamic output feedback controller successfully achieves the performance improvement under reference step changes and load variations.

  10. Optimal feed-forward compensation for PWM dc/dc converters with 'linear' and 'quadratic' conversion ratio

    Science.gov (United States)

    Calderone, Luigi; Pinola, Licia; Varoli, Vincenzo

    1992-04-01

    The paper describes an analytical procedure to optimize the feed-forward compensation for any PWM dc/dc converters. The aims of achieving zero dc audiosusceptibility was found to be possible for the buck, buck-boost, Cuk, and SEPIC cells; for the boost converter, however, only nonoptimal compensation is feasible. Rules for the design of PWM controllers and procedures for the evaluation of the hardware-introduced errors are discussed. A PWM controller implementing the optimal feed-forward compensation for buck-boost, Cuk, and SEPIC cells is described and fully experimentally characterized.

  11. ZVS Full-Bridge Based DC-DC Converter with Linear Voltage Gain According to Duty Cycle

    Science.gov (United States)

    Do, Hyun-Lark

    2013-09-01

    This paper presents a zero-voltage-switching (ZVS) full-bridge based DC-DC converter with linear voltage gain according to duty cycle. The proposed converter is based on an asymmetrical pulse-width-modulation (APWM) full-bridge converter which has various advantages over other converters. However, it has some drawbacks such as limited maximum duty cycle to 0.5 and narrow input range. The proposed converter overcomes these problems. The duty cycle is not limited and input voltage range is wide. Also, the ZVS operation of all power switches is achieved. Therefore, switching losses are significantly reduced and high-efficiency is obtained. Steady-state analysis and experimental results for the proposed converter are presented to validate the feasibility and the performance of the proposed converter.

  12. Integrated Solar Power Converters: Wafer-Level Sub-Module Integrated DC/DC Converter

    Energy Technology Data Exchange (ETDEWEB)

    None

    2012-02-09

    Solar ADEPT Project: CU-Boulder is developing advanced power conversion components that can be integrated into individual solar panels to improve energy yields. The solar energy that is absorbed and collected by a solar panel is converted into useable energy for the grid through an electronic component called an inverter. Many large, conventional solar energy systems use one, central inverter to convert energy. CU-Boulder is integrating smaller, microinverters into individual solar panels to improve the efficiency of energy collection. The University’s microinverters rely on electrical components that direct energy at high speeds and ensure that minimal energy is lost during the conversion process—improving the overall efficiency of the power conversion process. CU-Boulder is designing its power conversion devices for use on any type of solar panel.

  13. Efficiency and weight of voltage multiplier type ultra lightweight dc-dc converters

    Science.gov (United States)

    Harrigill, W. T., Jr.; Myers, I. T.

    1975-01-01

    An analytical and experimental study was made of a capacitor-diode voltage multiplier without a transformer which offers the possibility of high efficiency with light weight. The dc-dc conversion efficiencies of about 94 percent were achieved at output powers of 150 watts at 1000 volts using 8x multiplication. A detailed identification of losses was made, including forward drop losses in component, switching losses, reverse junction capacitance charging losses, and charging losses in the main ladder capacitors.

  14. Implementation of a PV lighting system based on DC-DC converter with intelligent controlled approach

    Energy Technology Data Exchange (ETDEWEB)

    Hua, C.-C.; Chuang, D.-J. [National Yunlin Univ. of Science and Technology, Douliou, Yunlin, Taiwan (China). Dept. of Electrical Engineering; Chuang, C.-W. [National Yunlin Univ. of Science and Technology, Douliou, Yunlin, Taiwan (China). Graduate School of Engineering Science and Technology

    2007-07-01

    Photovoltaic (PV) lighting systems for municipalities represent one of the largest cost effective markets for PVs. The installation cost of just one or two utility power poles can justify the initial cost of a PV lighting system. However, many previous PV lighting systems have experienced a number of component failures including premature charge controller, battery, and ballast illumination failures. This paper presented the design and implementation of a digital high performance photovoltaic lighting system based on a microcontroller. A high brightness light-emitting diode (HBLED), was used as it can work at very high efficiency with a specially designed lighting power module. The proposed system consisted of a photovoltaic module, a light emitting diode (LED) lighting module, a bi-directional buck-boost converter and a battery. The paper analysed battery charging methods and proposed a control strategy and hardware implementation. The dimming control methods for LED were also discussed and compared. The experimental results were also provided to verify the theoretical analysis and design procedure of a digital controlled photovoltaic lighting system. It was concluded that the experimental results verified the performance of the proposed photovoltaic lighting system. 8 refs., 1 tab., 18 figs.

  15. Dynamic Sliding Mode Evolution PWM Controller for a Novel High-Gain Interleaved DC-DC Converter in PV System

    Directory of Open Access Journals (Sweden)

    Taizhou Bei

    2014-01-01

    Full Text Available Considering the disadvantages of the traditional high-gain DC-DC converter such as big size, high voltage stress of switches, and large input current ripple, a novel high-gain interleaved boost converter with coupled-inductor and switched-capacitor was proposed correspondingly and the operation principle together with the steady-state analysis of this converter was also described. Besides, a new control approach-dynamic sliding mode evolution PWM controller (DSME PWM for the novel topological converter based on both dynamic evolution and sliding mode control was also presented. From the simulation results and experimental validation the proposed converter can fulfill high-gain boost, low ripple of both the input current and the output voltage. Furthermore, MPPT technique can be also achieved in a short time by simulation. The efficiency and stability of the converter proposed in this paper can be improved.

  16. A Dual-Mode Step-up DC/DC Converter IC with Current-Limiting and EMI Reduction Techniques

    Institute of Scientific and Technical Information of China (English)

    Wan-Rone Liou; Chun-Ting Kuo; Mei-Ling Yeh; Ping-Hsing Chen; Marynelle L. Z. Rosales

    2008-01-01

    This paper presents a novel dual-mode step-up (boost) DC/DC converter. Pulse-frequency modulation (PFM) is used to improve the efficiency at light load. This converter can operate between pulse-width modulation (PWM) and pulse-frequency modulation. The converter will operate in PFM mode at light load and in PWM mode at heavy load. The maximum conversion efficiency of this converter is 96%. The conversion efficiency is greatly improved when load current is below 100 mA. Additionally, a soft-start circuit and a variable-sawtooth frequency circuit are proposed in this paper. The former is used to avoid the large switching current at the start up of the converter and the latter is utilized to reduce the EMI of the converter.

  17. Open-circuit fault detection and tolerant operation for a parallel-connected SAB DC-DC converter

    DEFF Research Database (Denmark)

    Park, Kiwoo; Chen, Zhe

    2014-01-01

    This paper presents an open-circuit fault detection method and its tolerant control strategy for a Parallel-Connected Single Active Bridge (PCSAB) dc-dc converter. The structural and operational characteristics of the PCSAB converter lead to several advantages especially for high power applications....... By paralleling modular converters, the power and current ratings of each modular converter can be lowered and by interleaving the switching patterns, the input and output current ripples can be significantly reduced without increasing switching losses or device stresses. Apart from these, the PCSAB converter...... of the converter unaffected or to improve the quality of the output current under the fault condition. The feasibility of the proposed fault detection and fault-tolerant methods are verified by simulations and experiments....

  18. Optimization of DC-DC Converters for Improved Electromagnetic Compatibility With High Energy Physics Front-End Electronics

    CERN Document Server

    Fuentes, C; Michelis, S; Blanchot, G; Allongue, B; Faccio, F; Orlandi, S; Kayal, M; Pontt, J

    2011-01-01

    The upgrade of the Large Hadron Collider (LHC) experiments at CERN sets new challenges for the powering of the detectors. One of the powering schemes under study is based on DC-DC buck converters mounted on the front-end modules. The hard environmental conditions impose strict restrictions to the converters in terms of low volume, radiation and magnetic field tolerance. Furthermore, the noise emission of the switching converters must not affect the performance of the powered systems. A study of the sources and paths of noise of a synchronous buck converter has been made for identifying the critical parameters to reduce their emissions. As proof of principle, a converter was designed following the PCB layout considerations proposed and then used for powering a silicon strip module prototype for the ATLAS upgrade, in order to evaluate their compatibility.

  19. Wide-range 7-switch flying capacitor based dc-dc converter for point-of-load applications

    Science.gov (United States)

    Jain, Parth

    In this thesis a dc-dc converter referred to as the 7-switch flying capacitor (7SFC) based multi-level buck converter intended for point-of-load applications is presented. The 7SFC operates with the principle of "transformability" which allows it to run in several switching modes when paired with a digital controller. The mode is selected based on input and output conditions by estimating the highest efficiency mode. The 7SFC converter utilizes a flying capacitor, which for certain modes allows for a large reduction in switching losses, especially when the converter is operated with high-input voltages. Compared to the conventional 2-phase interleaved buck converter, the 7SFC is able to reduce the size of the output inductors and capacitor by 33%. The 7SFC discrete prototype is able to achieve efficiencies greater than 90% over the majority of the operating range.

  20. Startup Capability of Boost DC/DC Converter%Boost DC/DC的低压启动能力

    Institute of Scientific and Technical Information of China (English)

    向乾尹; 冯全源

    2011-01-01

    An analytical model was proposed to calculate the minimum startup voltage of a boost DC/ DC converter under a constant current load. The factors, such as the current load, the parasitic parameters, the saturation current and on-resistance of the power switch, the switching frequency, and the minimum startup voltage, etc. , which affect the startup capability of the boost DC/DC converter were analyzed with a steady-state analysis method. The model was applied to the design of a boost DC/ DC converter with a 0. 6 jxm CMOS process, and the maximum error of the minimum startup voltage calculated by the proposed model was 4. 5% compared with that by the HSPICE simulator.%为了准确预测Boost DC/DC低压启动能力,采用稳态分析方法,分析了电流负载、寄生参数、功率开关饱和电流及导通阻抗、开关频率、启动电路最低工作电压等因素对Boost DC/DC低压启动能力的影响,提出了预测Boost DC/DC恒流负载下最小启动电压的解析模型.将该模型应用于采用0.6 μm CMOS工艺的Boost DC/DC设计中,模型计算结果相对HSPICE仿真结果的最大误差为4.5%.本模型可推广至恒定电阻负载的情况.

  1. Hybrid electric system based on fuel cell and battery and integrating a single dc/dc converter for a tramway

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, Luis M., E-mail: luis.fernandez@uca.e [Department of Electrical Engineering, EPS Algeciras, University of Cadiz, Avda. Ramon Puyol, s/n. 11202 Algeciras (Cadiz) (Spain); Garcia, Pablo, E-mail: pablo.garcia@uca.e [Department of Electrical Engineering, EPS Algeciras, University of Cadiz, Avda. Ramon Puyol, s/n. 11202 Algeciras (Cadiz) (Spain); Garcia, Carlos Andres, E-mail: carlosandres.garcia@uca.e [Department of Electrical Engineering, EPS Algeciras, University of Cadiz, Avda. Ramon Puyol, s/n. 11202 Algeciras (Cadiz) (Spain); Jurado, Francisco, E-mail: fjurado@ujaen.e [Department of Electrical Engineering, EPS Linares, University of Jaen, C/Alfonso X, No. 28. 23700 Linares (Jaen) (Spain)

    2011-05-15

    Research highlights: {yields} Hybrid electric power system for a real surface tramway. {yields} Hybrid system based on PEM fuel cell with dc/dc converter and Ni-MH battery. {yields} New control strategy for the energy management of the tramway. {yields} Hybrid system demonstrated to meet appropriate driving cycle of the tramway. -- Abstract: This paper presents a hybrid electric power system for a real surface tramway. The hybrid system consists of two electrical energy sources integrating a single dc/dc converter to provide the power demanded by the tramway loads (four electric traction motors and auxiliary services): (1) a Polymer Electrolyte Membrane (PEM) fuel cell (FC) as the primary and (2) a rechargeable Ni-MH battery as electrical energy storage to supplement the FC over the driving cycle. According to the requirements of the real driving cycle of the tramway, it was considered a 200 kW PEM FC system with two FCs connected in parallel and a 34 Ah Ni-MH battery. The PEM FC and Ni-MH battery models were designed from commercially available components. The power conditioning system provides the appropriate power for the tramway. It is composed of: (1) a unique dc/dc boot converter which adapts the FC output voltage to the 750 V traction standard dc bus; (2) three phase inverters to drive properly each electric motors; and (3) a braking chopper to dissipate excess of regenerative braking energy. Suitable state machine control architecture is presented for the hybrid system, its objective being to provide demanded power by the driving cycle, optimizing the energy generated. Following this objective, a new state machine control strategy based on eight states decides the operating point of each component of the system and a cascade control structure allows achieving the operating points determined by the strategy. Simulation results of the real driving cycle of the tramway check the adequacy of the hybrid electric power system.

  2. Symmetrical dynamics of peak current-mode and valley current-mode controlled switching dc-dc converters with ramp compensation

    Science.gov (United States)

    Zhou, Guo-Hua; Xu, Jian-Ping; Bao, Bo-Cheng; Jin, Yan-Yan

    2010-06-01

    The discrete iterative map models of peak current-mode (PCM) and valley current-mode (VCM) controlled buck converters, boost converters, and buck-boost converters with ramp compensation are established and their dynamical behaviours are investigated by using the operation region, parameter space map, bifurcation diagram, and Lyapunov exponent spectrum. The research results indicate that ramp compensation extends the stable operation range of the PCM controlled switching dc-dc converter to D > 0.5 and that of the VCM controlled switching dc-dc converter to D converters with ramp compensation, VCM controlled switching dc-dc converters with ramp compensation exhibit interesting symmetrical dynamics. Experimental results are given to verify the analysis results in this paper.

  3. Digital Simulation of Closed Loop Zvs-Zcs Bidirectional Dc-Dc Converter for Fuel Cell and Battery Application

    Directory of Open Access Journals (Sweden)

    V. V. Subrahmanya Kumar Bhajana

    2010-08-01

    Full Text Available A closed loop ZVS-ZCS bidirectional dc-dc converter is modeled and appropriate digital simulations are provided. With the ZVS-ZCS concept, the MATLAB simulation results of application to a fuel cell and battery application have been obtained whenever the input voltage exceeds the given 24V, at that time the load voltage will change from 180V to 230V. But due to this usage the load is disturbed and there is instability in the model. Using closed loop the output voltage is stabilized.

  4. Bifurcation and chaos in multi-parallel-connected current-mode controlled boost DC-DC converters

    Institute of Scientific and Technical Information of China (English)

    CHEN Ming-liang; MA Wei-ming

    2006-01-01

    This paper studied the bifurcation and chaos phenomenon in a multi-parallel-connected current-mode controlled boost DC-DC converter system with the use of nonlinear mapping bifurcation theory of two dimensions,and the changing rules of the bifurcation charts with the increase of the control parallels and control parameters were concluded.The method of discrete mapping modeling was utilized to construct the difference equations of the system operating in continuous conduction mode (CCM).Analyses and computer emulations were made.

  5. Design of Performance Driven Self-Tuning PID Control Systems and It's Application for DC-DC Converters

    Science.gov (United States)

    Ohnishi, Yoshihiro; Ikemoto, Takahiro; Yamamoto, Toru

    This paper proposes an adaptive PID controller which is driven by current control performance. The calculations of the PID parameters are based on the generalized minimum variance control(GMVC) algorithm. The current control performance is obtained in an online manner over a user-specified time-window with some overlap. The retuning of PID parameters are only carried out when controller performance deteriorates below a user-specified threshold. Experimental evaluations on the voltage control of the DC-DC converter demonstrates the practicality and utility of this idea.

  6. Application of Multi-port Bidirectional DC-DC Converter to Fuel Cell Vehicle Driving in JC08 Mode

    Science.gov (United States)

    Tanaka, Katsunori; Katayama, Noboru; Kogoshi, Sumio; Fukada, Takafumi; Ogawa, Makoto

    A fuel cell-EDLC hybrid power system with a multi-port bidirectional DC-DC converter has been recently proposed for extending lifetime of a fuel cell due to smoothing the output current of the fuel cell. This paper studies the performance of the hybrid power system when a fuel cell vehicle drives in the JC08 mode using a simulation model. The simulation results indicate that even if the load current fluctuates, the output current of the fuel cell could be maintained at almost constant values with an assist from the EDLC although small spikes are observed.

  7. Swarming Speed Control for DC Permanent Magnet Motor Drive via Pulse Width Modulation Technique and DC/DC Converter

    Directory of Open Access Journals (Sweden)

    A.S. Oshaba

    2013-05-01

    Full Text Available This study presents an approach for the speed control of a permanent magnet DC motor drive via Pulse Width Modulation (PWM technique and a DC/DC converter. The Particle Swarm Optimization (PSO technique is used to minimize a time domain objective function and obtain the optimal controller parameters. The performance of the proposed technique has been evaluated using various types of disturbances including load torque variations. Simulation results illustrate clearly the robustness of the controller and validity of the design technique for controlling the speed of permanent magnet motors.

  8. Dual-Input Isolated Full-Bridge Boost DC-DC Converter Based on the Distributed Transformers

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2012-01-01

    In this paper, a new two-input isolated boost dc-dc converter based on a distributed multi-transformer structure which is suitable for hybrid renewable energy systems is investigated and designed. With a novel transformer winding-connecting strategy, the two input ports can be decoupled completely...... and the single-input mode, respectively. The main advantage of the proposed topology is that the four transformers and the secondary rectifiers are fully utilized whether the converter is connected with two input power sources or only one input. Although the four transformers are employed, the nominal powers...... of each transformer and rectifier are both reduced by four times. Furthermore, some special issues on converter design, such as increasing number of the input ports, the magnetic integration and the ground loop decoupling are discussed. A 2 kW prototype was built and tested. Experiments on the converter...

  9. A Dual-Mode Step-up DC/DC Converter IC with Current-Limiting and EMI Reduction Techniques

    Institute of Scientific and Technical Information of China (English)

    Wan-Rone Liou; Chun-Ting Kuo; Mei-Ling Yeh; Ping-Hsing Chen; Marynelle L. Z. Rosales

    2008-01-01

    This paper presents a novel dual-modestep-up (boost) DC/DC converter. Pulse-frequencymodulation (PFM) is used to improve the efficiency atlight load. This converter can operate betweenpulse-width modulation (PWM) and pulse-frequencymodulation. The converter will operate in PFM mode atlight load and in PWM mode at heavy load. Themaximum conversion efficiency of this converter is 96%.The conversion efficiency is greatly improved when loadcurrent is below 100 mA. Additionally, a soft-startcircuit and a variable-sawtooth frequency circuit areproposed in this paper. The former is used to avoid thelarge switching current at the start up of the converterand the latter is utilized to reduce the EMI of theconverter.

  10. A Comparative study of Analog and digital Controller On DC/DC Buck-Boost Converter Four Switch for Mobile Device Applications

    Directory of Open Access Journals (Sweden)

    Benlafkih Abdessamad

    2013-01-01

    Full Text Available this paper presents comparative performance between Analog and digital controller on DC/DC buck-boost converter four switch. The design of power electronic converter circuit with the use of closed loop scheme needs modeling and then simulating the converter using the modeled equations. This can easily be done with the help of state equations and MATLAB/SIMULINK as a tool for simulation of those state equations. DC/DC Buckboost converter in this study is operated in buck (step-down and boost (step-up modes.

  11. Modeling and Control of DC/DC Boost Converter using K-Factor Control for MPPT of Solar PV System

    DEFF Research Database (Denmark)

    Vangari, Adithya; Haribabu, Divyanagalakshmi; Sakamuri, Jayachandra N.

    2015-01-01

    This paper is focused on the design of a controller for the DC/DC boost converter using K factor control, which is based on modified PI control method, for maximum power point tracking (MPPT) of solar PV system. A mathematical model for boost converter based on small signal averaging approach...... is presented. Design of the passive elements of the boost converter as per the system specifications is also illustrated. The performance of the proposed K factor control method is verified with the simulations for MPPT on solar PV system at different atmospheric conditions. A new circuit based model for solar...... PV array, which includes the effect of solar insolation and temperature on PV array output, for the application in power system transient simulations, is also presented. The performance of the PV array model is verified with simulations at different atmospheric conditions. A 160W PV module from BP...

  12. A Pedagogical Approach for Modeling and Simulation of Switching Mode DC-DC Converters for Power Electronics Course

    Directory of Open Access Journals (Sweden)

    Han Yang

    2012-10-01

    Full Text Available The power electronics course is a rather challenging subject for instructors and undergraduate students pursuing Bachelor’s Degree in Electrical Engineering. To enhance teaching effectiveness and motivate self-learning capabilities of the students, this paper presents a pedagogical approach for mathematical modeling and simulation of switching mode DC-DC converters. The Buck and Boost converters are analyzed as benchmark systems to study the power converter modeling methodologies. And a comparative analysis using digital simulation from Matlab/Simulink and ATP/EMTP is presented. A summary of student survey is also presented, which shows a high level of satisfaction. The presented pedagogical approach would be useful for classroom teaching for the power electronics course and similar engineering courses.

  13. DC/DC开关变换器混沌现象研究综述%Summary of the Research on Chaos Phenomena of DC/DC Converter

    Institute of Scientific and Technical Information of China (English)

    蔚洋; 冯平

    2012-01-01

    DC/DC功率开关变换器是开关电源的核心部分,通过对其混沌现象的研究可以更加深刻地认识DC/DC变换器的本质,也会在将来基于混沌现象提出新的设计方法和控制策略,实现现有DC/DC变换器无法达到的性能.本文介绍了DC/DC变换器混沌现象的研究现状,对DC/DC变换器混沌现象的基本建模方法进行了综合对比分析,展望了DC/DC变换器混沌研究的发展和未来应用前景.%DC/DC power switch converter is the core part of switch power supply. Through the study of chaos phenomena, the essence of DC/DC converter can be more deeply understand, the new design methods and control strategies based on chaos phenomena will be put forward in the future, to achieve the existing DC/DC converter that cannot reach. This paper introduces the research status of the DC/DC converter chaos phenomena, makes comprehensive comparative analysis of the basic modeling method of DC/DC converter chaos phenomena, and looks to its development and future application prospect.

  14. Design and Simulation of Dc-Dc Converter for Fuel Cell Operated Vehicle with Single Reference Six Pulse Modulation

    Directory of Open Access Journals (Sweden)

    1V.Chaitanya,P.G.scholar,

    2015-10-01

    Full Text Available : Even though electrical vehicle concept is introduced in early 1800’s, it gained importance in past couple of decades due to growing conscience on environmental aspects. Different types of electrical vehicles are manufactured in the past centuries and now onboard generation is seems to be promising by fulfilling the needs of a vehicle. Fuel cells or fuel cell stack produces typically 32-68V of EMF, which has to be conditioned before it fed to motor. The conditioning involves two stages DCDC conversion and then to DC-AC conversion .DC-AC conversion is done through inverter. For DC-DC to conversion various topologies are proposed such as fly back, forward, buck-boost are proposed. This paper deals with the front end DC-DC converter and inverter switching. A hybrid modulation scheme is used to produce pulses to switch the source end full bridge rectifier and inverter at load end. In this modulation scheme high frequency pulses given to full bridge rectifier and 33% modulation scheme based pulses are produced for inverter switching.

  15. Super-Twisting Differentiator-Based High Order Sliding Mode Voltage Control Design for DC-DC Buck Converters

    Directory of Open Access Journals (Sweden)

    Yigeng Huangfu

    2016-06-01

    Full Text Available This paper aims to focus on the smooth output of DC-DC buck converters in wireless power transfer systems under input perturbations and load disturbances using the high-order sliding mode controller (HOSM and HOSM with super-twisting differentiator (HOSM + STD. The proposed control approach needs only measurement of converter output voltage. Theoretical analysis and design procedures, as well as the super-twisting differentiator of the proposed controller are presented in detail with the prescribed convergence law of high-order sliding modes. Comparisons of both simulation and experimental results among conventional proportional-integral (PI control, traditional sliding mode control (SMC, HOSM and HOSM + STD under various test conditions such as steady state, input voltage perturbations and output load disturbances, are presented and discussed. The results demonstrate and validate the effectiveness and robustness of the proposed control method.

  16. Simple digital PWM and PSM controlled DC-DC boost converter for luminance-regulated WLED driver

    Institute of Scientific and Technical Information of China (English)

    LIU Xin; GUO Shu-xu; CHANG Yu-chun; ZHU Shun-dong; WANG Shuai

    2009-01-01

    This article presents a control strategy based on simple digital pulse-width modulation (DPWM) and pulse-skip modulation (PSM) for a DC-DC boost converter, to drive a luminance-regulated white light emitting diodes (WLEDs). The presented control strategy not only retains most of the advantages and flexibilities of traditional digital PWM, but also reduces complexity and cost. Based on analyzing the principle of the presented control strategy, the white light emitting diode (WLED) driver is designed and simulated using the 0.6 (m CMOS process. Simulation results of the boost converter show that the power efficiency is above 76% for a full load, with a peak efficiency of 88% when supply voltage varies from 2.7 V to 5.5 V. The control strategy overcomes low efficiency for PWM mode with light load.

  17. SUPPRESSING CONDUCTED EMI FROM A DC/DC HIGH POWER CONVERTER BASED ON MIXED-MODE FILTER

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Conducted electromagnetic interference (EMI) from a 7.5kVA DC/DC high power converter is investigated to agree with EN class A. Here in some passive methods of suppressing conducted EM Noise, such as mixed-mode (MM) EMI filters, snubbing circuits and other means, are used. Based on measurement, the sources of noise are detected with the characteristics analyzed in detail. The MM EMI filters is valuable means with which low-frequency part and some of the high frequency part of conducted EM Noise can be efficiently reduced. How to lay out the MM filters on both sides of the converter is outlined in detail. In addition, multiple grounding and RDC snubbing circuits are employed to improve the performance in high frequency. The experimental results confirm the methods adopted.

  18. New non-linear control strategy for non-isolated DC/DC converter with high voltage ratio

    Energy Technology Data Exchange (ETDEWEB)

    Shahin, A.; Huang, B.; Martin, J.P.; Pierfederici, S.; Davat, B. [Groupe de Recherche en Electronique et en Electrotechnique de Nancy - INPL - Nancy Universite, 2, Avenue de la Foret de Haye, 54516 Vandoeuvre-les-Nancy Cedex (France)

    2010-01-15

    In this paper, a non-isolated DC/DC converter with high voltage ratio is proposed to allow the interface between a low voltage power source like fuel cell and a high voltage DC bus. To take into account the low voltage-high density characteristics of power sources, a cascaded structure composed of two sub-converters has been chosen and allows obtaining a high voltage ratio. The choice of each sub-converter is based on the requirements of the source and its performances. Consequently, we have chosen a three-interleaved boost converter as the 1st sub-converter whereas the 2nd sub-converter is a three-level boost converter. The control of the whole system is realized thanks to energetic trajectories planning based on flatness properties of the system. The control of both the current and the balance of voltage across the output serial capacitors of the three-level boost converter is ensured by non-linear controllers based on a new non-linear model. Experimental results allow validating the proposed power architecture and its associated control. (author)

  19. DCM, FSM, dead time and width controllers for a high frequency high efficiency buck DC-DC converter over a wide load range

    Energy Technology Data Exchange (ETDEWEB)

    Pi Changming; Yan Wei; Zhang Ke; Li Wenhong, E-mail: wenhongli@fudan.edu.c [State Key Laboratory of ASIC and Systems, Fudan University, Shanghai 201203 (China)

    2010-08-15

    This paper presents a width controller, a dead time controller, a discontinuous current mode (DCM) controller and a frequency skipping modulation (FSM) controller for a high frequency high efficiency buck DC-DC converter. To improve the efficiency over a wide load range, especially at high switching frequency, the dead time controller and width controller are applied to enhance the high load efficiency, while the DCM controller and FSM controller are proposed to increase the light load efficiency. The proposed DC-DC converter controllers have been designed and fabricated in the Chartered 0.35 {mu}m CMOS process, and the measured results show that the efficiency of the buck DC-DC converter is above 80% over a wide load current range from 8 to 570 mA, and the peak efficiency is 86% at 10 MHz switching frequency. (semiconductor integrated circuits)

  20. SEMICONDUCTOR INTEGRATED CIRCUITS: DCM, FSM, dead time and width controllers for a high frequency high efficiency buck DC-DC converter over a wide load range

    Science.gov (United States)

    Changming, Pi; Wei, Yan; Ke, Zhang; Wenhong, Li

    2010-08-01

    This paper presents a width controller, a dead time controller, a discontinuous current mode (DCM) controller and a frequency skipping modulation (FSM) controller for a high frequency high efficiency buck DC-DC converter. To improve the efficiency over a wide load range, especially at high switching frequency, the dead time controller and width controller are applied to enhance the high load efficiency, while the DCM controller and FSM controller are proposed to increase the light load efficiency. The proposed DC-DC converter controllers have been designed and fabricated in the Chartered 0.35 μm CMOS process, and the measured results show that the efficiency of the buck DC-DC converter is above 80% over a wide load current range from 8 to 570 mA, and the peak efficiency is 86% at 10 MHz switching frequency.

  1. Reduction of vehicle CO{sub 2} emission with application of DC/DC converter; Einsatz von DC/DC-Wandlern in Kraftfahrzeugen zur Reduzierung von CO{sub 2} Emissionen

    Energy Technology Data Exchange (ETDEWEB)

    Floettmann, B.; Weghaus, L.; Schoellmann, M. [Hella KGaA Hueck und Co., Lippstadt (Germany)

    2007-07-01

    DC to DC converter in vehicles are more and more enabling technologies for innovative powernet architectures which are required by new approaches to reduce fuel consumption. Increasing fuel prices and legislative requirements concerning emission are demanding for a close realization on the existing powernet. Applications like Stop/Start which can be implemented into todays powernet solutions requiring slight modifications only contribute already to reduction of CO{sub 2} emissions. This article describes different powernet architectures, which provide significant saving potential, on the basis of DC/DC-converter without representing a convenience limitation to the passenger. (orig.)

  2. 三重交错并联DC/DC变换器设计%Design of a triple interleaving DC/DC converter of composite power electric cars

    Institute of Scientific and Technical Information of China (English)

    张智林; 张彦会; 张群

    2012-01-01

    DC/DC变换器是复合电源电动汽车的重要组成部分之一,为了提高DC/DC变换器的功率密度,DC/DC变换器正在向高频化发展,研究在单相DC/DC变换器的基础上,设计了一种三重交错并联DC/DC变换器,可以提高系统的开关频率、降低纹波电压,从而减小滤波器的体积、提高功率密度.最后通过Simulink进仿真分析,结果表明:三重交错并联DC/DC变换器的纹波电压明显小于单相DC/DC变换器,有利于功率密度的提高.%DC/DC converter is the important part of composite power electric cars. In order to improve the power density of DC/DC converter, high frequency is required. This paper designs a triple inter/earing DC/DC converter based on the single phase DC/DC converter. It can reduce the ripple voltage effectively, reduce the volume of the filter and improve the switch frequency of the system. Finally, through the simulation analysis, the results show that the system efficiency of the triple interleaving DC/DC converter is better than the single phase DC/DC converter, thus the power density is increased.

  3. Performance evaluation of a high power DC-DC boost converter for PV applications using SiC power devices

    Science.gov (United States)

    Almasoudi, Fahad M.; Alatawi, Khaled S.; Matin, Mohammad

    2016-09-01

    The development of Wide band gap (WBG) power devices has been attracted by many commercial companies to be available in the market because of their enormous advantages over the traditional Si power devices. An example of WBG material is SiC, which offers a number of advantages over Si material. For example, SiC has the ability of blocking higher voltages, reducing switching and conduction losses and supports high switching frequency. Consequently, SiC power devices have become the affordable choice for high frequency and power application. The goal of this paper is to study the performance of 4.5 kW, 200 kHz, 600V DC-DC boost converter operating in continuous conduction mode (CCM) for PV applications. The switching behavior and turn on and turn off losses of different switching power devices such as SiC MOSFET, SiC normally ON JFET and Si MOSFET are investigated and analyzed. Moreover, a detailed comparison is provided to show the overall efficiency of the DC-DC boost converter with different switching power devices. It is found that the efficiency of SiC power switching devices are higher than the efficiency of Si-based switching devices due to low switching and conduction losses when operating at high frequencies. According to the result, the performance of SiC switching power devices dominate the conventional Si power devices in terms of low losses, high efficiency and high power density. Accordingly, SiC power switching devices are more appropriate for PV applications where a converter of smaller size with high efficiency, and cost effective is required.

  4. Analysis and Design of a Bidirectional Isolated DC-DC Converter for Fuel Cell and Super-Capacitor Hybrid System

    DEFF Research Database (Denmark)

    Zhang, Zhe; Ouyang, Ziwei; Thomsen, Ole Cornelius

    2012-01-01

    Electrical power system in future uninterruptible power supply (UPS) or electrical vehicle (EV) may employ hybrid energy sources, such as fuel cells and super-capacitors. It will be necessary to efficiently draw the energy from these two sources as well as recharge the energy storage elements...... by the DC bus. In this paper, a bidirectional isolated DC-DC converter controlled by phase-shift and duty cycle for the fuel cell hybrid energy system is analyzed and designed. The proposed topology minimizes the number of switches and their associated gate driver components by using two high frequency...... transformers which combine a half-bridge circuit and a full-bridge circuit together on the primary side. The voltage doubler circuit is employed on the secondary side. The current-fed input can limit the input current ripple that is favorable for fuel cells. The parasitic capacitance of the switches is used...

  5. Maximum power point tracking for photovoltaic applications by using two-level DC/DC boost converter

    Science.gov (United States)

    Moamaei, Parvin

    Recently, photovoltaic (PV) generation is becoming increasingly popular in industrial applications. As a renewable and alternative source of energy they feature superior characteristics such as being clean and silent along with less maintenance problems compared to other sources of the energy. In PV generation, employing a Maximum Power Point Tracking (MPPT) method is essential to obtain the maximum available solar energy. Among several proposed MPPT techniques, the Perturbation and Observation (P&O;) and Model Predictive Control (MPC) methods are adopted in this work. The components of the MPPT control system which are P&O; and MPC algorithms, PV module and high gain DC-DC boost converter are simulated in MATLAB Simulink. They are evaluated theoretically under rapidly and slowly changing of solar irradiation and temperature and their performance is shown by the simulation results, finally a comprehensive comparison is presented.

  6. Multiphase soft switched DC/DC converter and active control technique for fuel cell ripple current elimination

    Energy Technology Data Exchange (ETDEWEB)

    Lai, Jih-Sheng (Blacksburg, VA); Liu, Changrong (Sunnyvale, CA); Ridenour, Amy (Salem, VA)

    2009-04-14

    DC/DC converter has a transformer having primary coils connected to an input side and secondary coils connected to an output side. Each primary coil connects a full-bridge circuit comprising two switches on two legs, the primary coil being connected between the switches on each leg, each full-bridge circuit being connected in parallel wherein each leg is disposed parallel to one another, and the secondary coils connected to a rectifying circuit. An outer loop control circuit that reduces ripple in a voltage reference has a first resistor connected in series with a second resistor connected in series with a first capacitor which are connected in parallel with a second capacitor. An inner loop control circuit that reduces ripple in a current reference has a third resistor connected in series with a fourth resistor connected in series with a third capacitor which are connected in parallel with a fourth capacitor.

  7. Optimizing the dynamics of a two-cell DC-DC buck converter by time delayed feedback control

    Science.gov (United States)

    Feki, M.; El Aroudi, A.; Robert, B. G. M.; Martínez-Salamero, L.

    2011-11-01

    A study of the dynamical behavior of a two-cell DC-DC buck converter under a digital time delayed feedback control (TDFC) is presented. Various numerical simulations and dynamical aspects of this system are illustrated in the time domain and in the parameter space. Without TDFC, the system may present many undesirable behaviors such as sub-harmonics and chaotic oscillations. TDFC is able to widen the stability range of the system. Optimum values of parameters giving rise to fast response while maintaining stable periodic behavior are given in closed form. However, it is detected that in a certain region of the parameter space, the stabilized periodic orbit may coexist with a chaotic attractor. Boundary between basins of attraction are obtained by means of numerical simulations.

  8. High voltage dc-dc converter with dynamic voltage regulation and decoupling during load-generated arcs

    Science.gov (United States)

    Shimer, Daniel W.; Lange, Arnold C.

    1995-01-01

    A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

  9. TID and Displacement Damage Effects in Vertical and Lateral Power MOSFETs for Integrated DC-DC Converters

    CERN Document Server

    Faccio, F; Michelis, S; Faccio, Federico; Fuentes, C; Allongue, B; Sorge, R; Orlandi, S

    2010-01-01

    TID and displacement damage effects are studied for vertical and lateral power MOSFETs in five different technologies in view of the development of radiation-tolerant fully integrated DC-DC converters. Investigation is pushed to the very high level of radiation expected for an upgrade to the LHC experiments. TID induces threshold voltage shifts and, in n-channel transistors, source-drain leakage currents. Wide variability in the magnitude of these effects is observed. Displacement damage increases the on-resistance of both vertical and lateral high-voltage transistors. In the latter case, degradation at high particle fluence might lead to a distortion of the output characteristics curve. HBD techniques to limit or eliminate the radiation-induced leakage currents are successfully applied to these high-voltage transistors, but have to be used carefully to avoid consequences on the breakdown voltage.

  10. Fault Tolerant Operation of ISOP Multicell Dc-Dc Converter Using Active Gate Controlled SiC Protection Switch

    Directory of Open Access Journals (Sweden)

    Yusuke Hayashi

    2016-01-01

    Full Text Available An active gate controlled semiconductor protection switch using SiC-MOSFET is proposed to achieve the fault tolerant operation of ISOP (Input Series and Output Parallel connected multicell dc-dc converter. The SiC-MOSFET with high temperature capability simplifies the configuration of the protection circuit, and its on-resistance control by the active gate controller realizes the smooth protection without the voltage and the current surges. The first laboratory prototype of the protection switch is fabricated by using a SiC-MOSFET with a high frequency buck chopper for the active gate controller. The effectiveness of the proposed protection switch is verified, taking the impact of the volume reduction into account.

  11. Comparative Analysis on Three Kinds of Combined DC-DC Converter Mode Inverters with High Frequency Link%三类组合直流变换器型高频环节逆变器的分析比较

    Institute of Scientific and Technical Information of China (English)

    陈艳慧; 陈道炼

    2012-01-01

    The combined DC-DC converter mode inverters with high frequency link is composed of two same isolated bi-directional DC-DC converters which are connected in parallel on the input side and reversely connected in series on the output side including Buck, Boost, and Buck-Boost mode. The circuit topology, control strategy, input current ripple, output voltage ripple, key parameters and test waveforms of three kinds of inverter were comparatively studied and an important conclusion was obtained.%组合直流变换器型高频环节逆变器是由两个相同的隔离双向直流变换器输入侧并联、输出侧反向串联构成,包括Buck、Boost、Buck-Boost型三类。主要对Buck、Boost、Buck-Boost组合直流变换器型高频环节逆变器的电路拓扑、控制策略、输入电流纹波、输出电压纹波、关键电路参数、原理实验波形等方面进行了比较研究,获得了重要结论。

  12. Analysis and design of a parallel-connected single active bridge DC-DC converter for high-power wind farm applications

    DEFF Research Database (Denmark)

    Park, Kiwoo; Chen, Zhe

    2013-01-01

    This paper presents a parallel-connected Single Active Bridge (SAB) dc-dc converter for high-power applications. Paralleling lower-power converters can lower the current rating of each modular converter and interleaving the outputs can significantly reduce the magnitudes of input and output current...... requirements, this modular converter concept is expected to be highly beneficial especially for the offshore wind farm application....

  13. Self-oscillating Galvanic Isolated Bidirectional Very High Frequency DC-DC Converter

    DEFF Research Database (Denmark)

    Pedersen, Jeppe Arnsdorf; Madsen, Mickey Pierre; Knott, Arnold;

    2015-01-01

    This paper describes a galvanic isolated bidirectional Very High Frequency (VHF = 30 MHz - 300MHz) ClassE converter. The reason for increasing the switching frequency is to minimize the passive components in the converter. To make the converter topology bidirectional the rectifier has to be synch......This paper describes a galvanic isolated bidirectional Very High Frequency (VHF = 30 MHz - 300MHz) ClassE converter. The reason for increasing the switching frequency is to minimize the passive components in the converter. To make the converter topology bidirectional the rectifier has...... conduction mode. The designed converter operates at a switching frequency of 35.6 MHz, which is well within the VHF range. The same converter is also implemented with PCB embedded inductors to minimize cost and the physical volume of the total converter....

  14. Stability analysis of a high-step-Up DC grid-connected two-stage boost DC-DC converter

    Directory of Open Access Journals (Sweden)

    El Aroudi A.

    2014-01-01

    Full Text Available High conversion ratio switching converters are used whenever there is a need to step-up dc source voltage level to a much higher output dc voltage level such as in photovoltaic systems, telecommunications and in some medical applications. A simple solution for achieving this high conversion ratio is by cascading different stages of dc-dc boost converters. The individual converters in such a cascaded system are usually designed separately applying classical design criteria. However these criteria may not be applicable for the complete cascaded system . This paper first presents a glimpse on the bifurcation behavior that a cascade connection of two boost converters can exhibit. It is shown that the desired periodic orbit can undergo period doubling leading to subharmonic oscillations and chaotic regimes. Then, in order to simplify the analysis the second stage is considered as constant current sink and design-oriented analysis is carried out to obtain stability boundaries in the parameter space by taking into account slope interactions between the state variables in the two-different stages.

  15. Analysis of a Multilevel Dual Active Bridge (ML-DAB DC-DC Converter Using Symmetric Modulation

    Directory of Open Access Journals (Sweden)

    M. A. Moonem

    2015-04-01

    Full Text Available Dual active bridge (DAB converters have been popular in high voltage, low and medium power DC-DC applications, as well as an intermediate high frequency link in solid state transformers. In this paper, a multilevel DAB (ML-DAB has been proposed in which two active bridges produce two-level (2L-5L, 5L-2L and 3L-5L voltage waveforms across the high frequency transformer. The proposed ML-DAB has the advantage of being used in high step-up/down converters, which deal with higher voltages, as compared to conventional two-level DABs. A three-level neutral point diode clamped (NPC topology has been used in the high voltage bridge, which enables the semiconductor switches to be operated within a higher voltage range without the need for cascaded bridges or multiple two-level DAB converters. A symmetric modulation scheme, based on the least number of angular parameters rather than the duty-ratio, has been proposed for a different combination of bridge voltages. This ML-DAB is also suitable for maximum power point tracking (MPPT control in photovoltaic applications. Steady-state analysis of the converter with symmetric phase-shift modulation is presented and verified using simulation and hardware experiments.

  16. New DC/DC High Step Up Isolated Converter with ZVS

    Directory of Open Access Journals (Sweden)

    Ehsan Movahedi

    2014-10-01

    Full Text Available In this paper we presents a soft switch sepic, flyback converter. At first the converter have hard switching in main switch and completely analysis then added auxiliary circuit for soft switching Auxiliary circuit in the converter is not only soft switching condition for the main switch but also prevents the spike voltage across the main switch when turned off that because leakage inductance. Therefore, the proposed converter efficiency in comparison with the previous converters increased and voltage stress on the main switch is reduced. Also the auxiliary switch in the converter have soft switching and thereby decrese losses. this converter Control with pwm.These converter have higher efficiency than the similar converters and the cost is low. Auxiliary circuit in the converter is not only soft switching condition for the main switch but also prevents the spike voltage across the main switch when turned off that because leakage inductance. Therefore, the proposed converter efficiency in comparison with the previous converters increased and voltage stress on the main switch is reduced.

  17. Modular DC-DC converter system for energy harvesting with EAPs

    Science.gov (United States)

    Eitzen, L.; Graf, C.; Maas, J.

    2013-04-01

    Energy harvesting with EAPs requires an energy-efficient power electronics providing a bidirectional energy transfer and operating voltages of up to several kilovolts. A possibility to achieve a high energy-efficiency for high voltage conversion is the use of a modular converter system consisting of several bidirectional converter modules, which are connected in series on the converter output side and in parallel at the input side. Since each converter stage provides only a part of the overall converter output voltage, the converter module output voltages can effectively be reduced by choosing the number of cascaded converter modules appropriately. This allows the use of standard semiconductor switches with superior electrical characteristics compared to high voltage semiconductors, enabling a high energy-efficiency and smaller passive components. Since EAP devices exhibit a mainly capacitive behavior and a limitation of the operating current is required for electrode protection, the utilized converter structure/topology has to be operated as a controllable current source on the lowest control level, which is achieved by operating the converter modules of the modular converter system with a subordinate closed-looped current control scheme. In order to avoid voltage unbalances among the single converter modules, a method for voltage balancing is presented. For validation, experimental results of a realized bidirectional flyback converter prototype are presented and discussed.

  18. Modeling and Design of Five Level Cascaded H-Bridge Multilevel Inverter with DC/DC Boost Converter

    Directory of Open Access Journals (Sweden)

    Vinayaka B.C

    2014-06-01

    Full Text Available Power electronic converters, especially DC/AC Sinusoidal Pulse Width Modulation inverters have been extending their range of use in industry because of their numerous advantages. They typically synthesize the stair –case voltage waveform (from several dc sources which has reduced harmonic content. This paper aims to extend the knowledge about the performance of Five level Cascaded H-Bridge MLI topology with DC/DC Boost Converter using SPWM for fixed DC Source. The output voltage is the sum of the voltage that is generated by each bridge. The switching angles can be chosen in such a way that the total harmonic distortion is minimized. This topology incorporates Boost Converter in the input side which magnifies the fundamental output voltage with reduction in total harmonic distortion. It also incorporates LC filter and hence output is drawn near the sine wave because of more levels. Results of experiments proved efficiency of 95%.The performance of the proposed SPWM strategy in terms of output voltage and THD has studied successfully and shown using MATLAB/Simulink.

  19. Microprocessor control of multiple peak power tracking DC/DC converters for use with solar cell arrays

    Science.gov (United States)

    Frederick, Martin E. (Inventor); Jermakian, Joel (Inventor)

    1991-01-01

    A method and an apparatus is provided for efficiently controlling the power output of a solar cell array string or a plurality of solar cell array strings to achieve a maximum amount of output power from the strings under varying conditions of use. Maximum power output from a solar array string is achieved through control of a pulse width modulated DC/DC buck converter which transfers power from a solar array to a load or battery bus. The input voltage from the solar array to the converter is controlled by a pulse width modulation duty cycle, which in turn is controlled by a differential signal controller. By periodically adjusting the control voltage up or down by a small amount and comparing the power on the load or bus with that generated at different voltage values a maximum power output voltage may be obtained. The system is totally modular and additional solar array strings may be added to the system simply by adding converter boards to the system and changing some constants in the controller's control routines.

  20. Identifier-based adaptive neural dynamic surface control for uncertain DC-DC buck converter system with input constraint

    Science.gov (United States)

    Chen, Qiang; Ren, Xuemei; Oliver, Jesus Angel

    2012-04-01

    In this paper, an identifier-based adaptive neural dynamic surface control (IANDSC) is proposed for the uncertain DC-DC buck converter system with input constraint. Based on the analysis of the effect of input constraint in the buck converter, the neural network compensator is employed to ensure the controller output within the permissible range. Subsequently, the constrained adaptive control scheme combined with the neural network compensator is developed for the buck converter with uncertain load current. In this scheme, a newly presented finite-time identifier is utilized to accelerate the parameter tuning process and to heighten the accuracy of parameter estimation. By utilizing the adaptive dynamic surface control (ADSC) technique, the problem of "explosion of complexity" inherently in the traditional adaptive backstepping design can be overcome. The proposed control law can guarantee the uniformly ultimate boundedness of all signals in the closed-loop system via Lyapunov synthesis. Numerical simulations are provided to illustrate the effectiveness of the proposed control method.

  1. Efficiency and hardware comparison of analog control-based and digital control-based 70 W two-stage power factor corrector and DC-DC converters

    DEFF Research Database (Denmark)

    Török, Lajos; Munk-Nielsen, Stig

    2011-01-01

    A comparison of an analog and a digital controller driven 70 W two-stage power factor corrector converter is presented. Both controllers are operated in average current-mode-control for the PFC and peak current control for the DC-DC converter. Digital controller design and converter modeling...... is described. Results show that digital control can compete with the analog one in efficiency, PFC and THD....

  2. Modelling and Simulation of Variable Frequency Synchronous DC-DC Buck Converter

    Directory of Open Access Journals (Sweden)

    Jeya Selvan Renius

    2014-10-01

    Full Text Available In this paper, novel small-signal averaged models for dc–dc converter operating at variable switching frequency are derived. This is achieved by separately considering the on-time and the off-time of the switching period. The derivation is shown in detail for a synchronous buck converter. The Enhanced Small Signal (ESSA Model is derived for the synchronous buck converter. The equivalent series inductance (ESL is also considered in this modelling. The buck converter model is also simulated in MATLAB and the result is also presented.

  3. Thermal analysis of spacecraft DC/DC converters%航天器DC/DC变换器热分析研究

    Institute of Scientific and Technical Information of China (English)

    艾华斌; 王卫国; 袁亚飞

    2013-01-01

    为了解决航天器DC/DC变换器的热可靠性问题,利用有限元分析软件ANSYS对实际的航天器DC/DC变换器进行热仿真分析,得到了其内部的温度分布特性。并对其进行了红外成像测试实验,通过红外成像测试结果与仿真分析结果对比分析,验证了热仿真的准确性。使用有限元分析方法为航天器DC/DC变换器合理热设计提供了依据,也为同类电子设备的热设计提供了一种思路。%In order to improve the thermal reliability of spacecraft DC/DC converters,the finite element analysis software (ANSYS)was used to conduct the thermal simulation and analysis for the actual spacecraft DC/DC converters,by which the in-ternal temperature distribution of spacecraft DC/DC converters was obtained. Furthermore,the infrared imaging testing experi-ment was performed for the DC/DC converters. the accuracy of the thermal simulation was verified by comparing the simulation analysis result with the infrared imaging testing result. The finite element analysis is adopted in this paper to provide an evi-dence for rationality of thermal design of spacecraft DC/DC converters,and a method for the thermal design of similar electronic equipments.

  4. Gate Driver Circuit of Power Electronic Switches with Reduced Number of Isolated DC/DC Converter for a Switched Reluctance Motor

    Directory of Open Access Journals (Sweden)

    Ali Asghar Memon

    2013-04-01

    Full Text Available This paper presents a gate driver circuit for the switching devices used in the asymmetrical converter for a switched reluctance machine with reduced number of isolated dc/dc converters. Isolation required in the gate driver circuit of switching devices is indispensable. For the purpose of isolation different arrangements may be used such as pulse transformers. The dc/dc converter for isolation and powering the gate drive circuits is suitable, cheaper in cost and simple to implement. It is also significant that required number of isolation converters is much less than the switches used in converter. In addition, a simple logic circuit has been presented for producing the gate signals at correct phase sequence which is compared with the gated signals directly obtained from the encoder of an existing machine.

  5. A Cryogenic Dc-Dc Power Converter for a 100 kW Synchronous HTS Generator at Liquid Nitrogen Temperatures

    Science.gov (United States)

    Bailey, Wendell; Wen, Hauming; Yang, Yifeng; Forsyth, Andrew; Jia, Chungjiang

    A dc-dc converter has been developed for retrofitting inside the vacuum space of the HTS rotor of a synchronous generator. The heavy copper sections of the current leads used for energising the HTS field winding were replaced by cryogenic power electronics; consisting of the converter and a rotor control unit. The converter board was designed using an H-bridge configuration with two 5A rated wires connecting the cryogenic boards to the stator control board located on the outside of the generator and drawing power from a (5A, 50 V) dc power source. The robustness of converter board was well demonstrated when it was powered up from a cold start at 82K. When charging the field winding with moderate currents (30A), the heat in-leak to the 'cold' rotor core was only 2W. It continued to function down to 74K, surviving several quenches. However, the quench protection function failed when injecting 75A into the field winding, resulting in the burn out of one of the DC-link capacitors. The magnitudes of the critical currents measured with the original current leads were compared to the quench currents, which was defined as the current which triggered quench protection protocol. The difference between the two currents was rather large, (∼20A). However, additional measurements using a single HTS coil in liquid nitrogen found that this reduction should not be so dramatic and in the region of 4A. Our conclusions identified the converter's switching voltage and its operating frequency as two parameters, which could have contributed to lowering the quench current. Magnetic fields and eddy currents are expected to be more prominent the field winding and its impact on the converter also need further investigation.

  6. High efficiency isolated DC/DC converter inherently optimized for fuel cell applications

    DEFF Research Database (Denmark)

    Petersen, Lars Press; Jensen, Lasse Crone; Larsen, Martin Norgaard

    2013-01-01

    The isolated full-bridge boost converter has been suggested as the best choice for fuel cell applications. Comparisons have been carried out in the literature using both stress factors and experimental verified designs to determine the optimal converter. Never the less, this paper suggests a diff...

  7. A Novel Quadratic Buck-Boost DC-DC Converter without Floating Gate-Driver

    DEFF Research Database (Denmark)

    Mostaan, Ali; A. Gorji, Saman; N. Soltani, Mohsen

    2016-01-01

    for floating gate driver. In addition, the voltage stress of one of the switches is lower than the existing quadratic buck-boost converters. Performance of the analytical results is validated using both simulation in MATLAB/SIMULINK and experimental tests where the proposed converter is evaluated in both buck...

  8. Design and Implementation of Power Flow Control for a novel Dual Input DC-DC Converter

    DEFF Research Database (Denmark)

    Taeed, Fazel; Ouyang, Ziwei; Nymand, Morten

    2014-01-01

    In this paper a control strategy for controlling the power flow from input voltage sources of a novel dual-input dcdc converter to the load is introduced. The converter can be used in renewable energy applications with two independent power sources. Firstly, the operation principle of the converter...... to control the power flow in the converter. The implemented controller in FPGA is low cost and simple. The complete system can be practically used in power management for renewable energy sources....... is outlined; then the control method for adjusting power sharing is proposed. In the next step, the controller is implemented in an FPGA, and then a 350W dual input converter is built to verify operation of the proposed control strategy. The experimental results show the excellent ability of the controller...

  9. Compact DC-DC Converter for Pocket Micro-Controller Systems

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    Novel compact DC-C converters for pocket micro-controller systems are discussed in the paper,which are based on switched capcotprs and inductorless,consequently are more suitable for being hybridized.The new converters enable the pocket microcontroller system to be powered by only one+12V source,while+5V and -12V are converted from the +12V source.The basic principle,voltage ratio,efficiency and ripples are analysed.Experiment and SPICE simulation are also given,which show positive results.

  10. A Novel Soft Computing Based Algorithm for the Control of Dynamic Uncertain Systems - An Application to DC-DC Converters

    Directory of Open Access Journals (Sweden)

    Abdul kareem

    2011-04-01

    Full Text Available Both Soft computing based controllers and sliding mode controllers have been utilized to regulate the output voltage of dc-dc converters in response to changes in the load and the input voltage. Although both control techniques possess desirable characteristics, they have disadvantages which prevent them from being applied extensively. Many researchers have proposed the combination of sliding mode control and Soft computing based control to combine the advantages of both control techniques. In literature survey, it is found that the combination of the methods are proposed so that sliding mode algorithm is used in the design of Soft computing based controllers and the inputs to the controller are error and change in error and the inherent stability property of sliding mode controller is not utilized. This paper presents a novel soft computing based sliding mode controller in which inputs are switching function and change in switching function which combines the advantages of soft computing based controllers, sliding mode controllers and integral controllers. Since soft computing is used in the design of sliding mode controller, the stability of the proposed controller is assured. In addition, it is well suited for digital control design and implementation. The proposed controller has been designed for a buck converter and the controller is able to obtain the desired transient response without causing chattering and error under steady-state conditions. The proposed controller is able to give robust performance in terms of rejection to input voltage variations and load variations.

  11. A 1 MW, 100 kV, less than 100 kg space based dc-dc power converter

    Science.gov (United States)

    Cooper, J. R.; White, C. W.

    1991-01-01

    A 1 MW dc-dc power converter has been designed which has an input voltage of 5 kV +/-3 percent, an output voltage of 100 kV +/- 0.25 percent, and a run time of 1000 s at full power. The estimated system mass is 83.8 kg, giving a power density of 11.9 kW/kg. The system exceeded the weight goal of 10 kW/kg through the use of innovative components and system concepts. The system volume is approximately 0.1 cu m, and the overall system efficiency is estimated to be 87 percent. Some of the unique system features include a 50-kHz H-bridge inverter using MOS-controlled thyristors as the switching devices, a resonance transformer to step up the voltage, open-cycle cryogenic hydrogen gas cooling, and a nonrigid, inflatable housing which provides on-demand pressurization of the power converter local environment. This system scales very well to higher output powers. The weight of the 10-MW system with the same input and output voltage requirements and overall system configuration is estimated to be 575.3 kg. This gives a power density of 17.4 kW/kg, significantly higher than the 11.9 kW/kg estimated at 1 MW.

  12. Ac-dc Bus-interface Bi-directional Converters in Renewable Energy Systems

    OpenAIRE

    Dong, Dong

    2012-01-01

    This dissertation covers several issues related to the ac-dc bus-interface bi-directional converters in renewable energy systems. The dissertation explores a dc-electronic distribution system for residential and commercial applications with a focus on the design of an ac-dc bi-directional converter for such application. This converter is named as the â Energy Control Centerâ due to its unique role in the system. First, the impact of the unbalanced power from the ac grid, especially the ...

  13. DC-DC converters in distributed photovoltaic electricity system. Analysis, control and design

    Energy Technology Data Exchange (ETDEWEB)

    Huusari, J.

    2012-10-15

    This thesis presents a comprehensive review on switched-mode converters in terms of dynamic behavior and practical limitations that arise from the fundamental properties of the electrical sources and loads, control engineering principles and topological properties of the converters. The main focus is on analyzing the behavior of a single converter used to interface a photovoltaic generator into a high-voltage dc link. The main objective is to introduce interfacing principles with numerous examples and a thorough discussion. The interfacing of photovoltaic generators by means of switched-mode converters has proven to be problematic according to numerous scientific publications indicating operational disadvantages and anomalies. The output characteristics of the photovoltaic generator, which are bound to varying environmental conditions, introduce design challenges. It has been recognized recently that the photovoltaic generator does not contain similar electrical behavior as conventional electrical sources, most notably due to its limited-power characteristics, yielding two distinctive operating regions. Yet, the constraints arising from the properties of the source have not been completely recognized, although the effect of these constraints can be seen from the published research results. When switched-mode converters are used to adapt individual photovoltaic modules into larger system by connecting converters in series or in parallel, severe operational limitations are observed. On the other hand, if the photovoltaic generator is substituted with a source that does not contain similar characteristics, observations may lead to misconclusions as the effect of the photovoltaic generator is not properly modeled. Therefore, claims that are not valid for actual applications with photovoltaic generators may be presented and widely accepted. This thesis presents methods to perform proper analysis of switched-mode converters implemented in distributed photovoltaic

  14. Integrated on-chip 0.35 μm BiCMOS current-mode DC-DC buck converter

    Science.gov (United States)

    Lee, Chan-Soo; Kim, Nam-Soo; Gendensuren, Munkhsuld; Choi, Jae-Ho; Choi, Joong-Ho

    2012-12-01

    A current-mode DC-DC buck converter with a fully integrated power module is presented in this article. The converter is implemented using BiCMOS technology in amplifier and power MOSFET in a current sensor. The current sensor is realised by the power lateral double-diffused MOSFET with the aspect ratio much larger than that of a matched p-MOSFET. In addition, BiCMOS technology is applied in the error amplifier for an accurate current sensing and a fast transient response. The DC-DC converter is fabricated with 0.35 µm BiCMOS process. Experimental results show that the fully integrated converter operates at 1.3 MHz switching frequency with a supply voltage of 5 V. The output DC voltage is obtained as expected and the output ripple is controlled to be within 2% with a 30 µH off-chip inductor and 100 µF off-chip capacitor.

  15. The DC-DC converter reduces its size and increases its efficiency; Le convertisseur DC-DC reduit sa taille et augmente son rendement

    Energy Technology Data Exchange (ETDEWEB)

    Feste, J.P.

    2000-03-01

    The DC to DC converters built by the US SynQor company use a dual stage conversion technique. One stage is devoted to regulation and the other to insulation. This technique allows to combine a high efficiency (up to 90%) with small dimensions. Instead of the classical Schottky diodes, a synchronous MOSFET is used for the rectification of the low voltage current. A simple air flow is required for the cooling of these converters. Short paper. (J.S.)

  16. A study of DC-DC converters with MCT's for arcjet power supplies

    Science.gov (United States)

    Stuart, Thomas A.

    1994-01-01

    Many arcjet DC power supplies use PWM full bridge converters with large arrays of parallel FET's. This report investigates an alternative supply using a variable frequency series resonant converter with small arrays of parallel MCT's (metal oxide semiconductor controlled thyristors). The reasons for this approach are to: increase reliability by reducing the number of switching devices; and decrease the surface mounting area of the switching arrays. The variable frequency series resonant approach is used because the relatively slow switching speed of the MCT precludes the use of PWM. The 10 kW converter operated satisfactorily with an efficiency of over 91 percent. Test results indicate this efficiency could be increased further by additional optimization of the series resonant inductor.

  17. All Digital Switch-Mode DC/DC Converters with BIST Functionality for Harsh Space Environments Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Space Micro ?Arizona State University (ASU) team will develop an all-digitally controlled, wide temperature range point-of-load switch-mode DC-DC regulator core...

  18. Modeling, Dynamics, Bifurcation Behavior and Stability Analysis of a DC-DC Boost Converter in Photovoltaic Systems

    Science.gov (United States)

    Zhioua, M.; El Aroudi, A.; Belghith, S.; Bosque-Moncusí, J. M.; Giral, R.; Al Hosani, K.; Al-Numay, M.

    A study of a DC-DC boost converter fed by a photovoltaic (PV) generator and supplying a constant voltage load is presented. The input port of the converter is controlled using fixed frequency pulse width modulation (PWM) based on the loss-free resistor (LFR) concept whose parameter is selected with the aim to force the PV generator to work at its maximum power point. Under this control strategy, it is shown that the system can exhibit complex nonlinear behaviors for certain ranges of parameter values. First, using the nonlinear models of the converter and the PV source, the dynamics of the system are explored in terms of some of its parameters such as the proportional gain of the controller and the output DC bus voltage. To present a comprehensive approach to the overall system behavior under parameter changes, a series of bifurcation diagrams are computed from the circuit-level switched model and from a simplified model both implemented in PSIM© software showing a remarkable agreement. These diagrams show that the first instability that takes place in the system period-1 orbit when a primary parameter is varied is a smooth period-doubling bifurcation and that the nonlinearity of the PV generator is irrelevant for predicting this phenomenon. Different bifurcation scenarios can take place for the resulting period-2 subharmonic regime depending on a secondary bifurcation parameter. The boundary between the desired period-1 orbit and subharmonic oscillation resulting from period-doubling in the parameter space is obtained by calculating the eigenvalues of the monodromy matrix of the simplified model. The results from this model have been validated with time-domain numerical simulation using the circuit-level switched model and also experimentally from a laboratory prototype. This study can help in selecting the parameter values of the circuit in order to delimit the region of period-1 operation of the converter which is of practical interest in PV systems.

  19. Implementation of Rapid Prototyping Tools for Power Loss and Cost Minimization of DC-DC Converters

    Directory of Open Access Journals (Sweden)

    Amruta V. Kulkarni

    2016-07-01

    Full Text Available In this paper, power loss and cost models of power electronic converters based on converter ratings and datasheet information are presented. These models aid in creating rapid prototypes which facilitate the component selection process. Through rapid prototyping, users can estimate power loss and cost which are essential in design decisions. The proposed approach treats main power electronic components of a converter as building blocks that can be arranged to obtain multiple topologies to facilitate rapid prototyping. In order to get system-level power loss and cost models, two processes are implemented. The first process automatically provides minimum power loss or cost estimates and identifies components for specific applications and ratings; the second process estimates power losses and costs of each component of interest as well as the whole system. Two examples are used to illustrate the proposed approaches—boost and buck converters in continuous conduction mode. Achieved cost and loss estimates are over 93% accurate when compared to measured losses and real cost data. This research presents derivations of the proposed models, experimental validation of the models and demonstration of a user friendly interface that integrates all the models. Tools presented in this paper are expected to be very useful for practicing engineers, designers, and researchers, and are flexible and adaptable with changing or new technologies and varying component prices.

  20. Control and modulation for loss minimization for dc/dc converters in wind farm

    DEFF Research Database (Denmark)

    Dincan, Catalin Gabriel; Kjær, Philip Carne

    2016-01-01

    For a DC wind turbine, a single phase series-resonant converter for unidirectional power is studied. This paper aims to identify and compare impact on electrical losses and component ratings from the choice of three candidate control strategies. The evaluation is purely based on circuit simulatio...

  1. High Efficiency Non-isolated Three Port DC-DC Converter for PV-Battery Systems

    DEFF Research Database (Denmark)

    Tomas Manez, Kevin; Anthon, Alexander; Zhang, Zhe;

    2016-01-01

    This paper presents a nonisolated Three Port Converter (TPC) with a unidirectional port for photovoltaic (PV) panels and a bidirectional port for energy storage. With the proposed topology single power conversion is performed between each port, so high efficiencies are obtained. A theoretical ana...

  2. Observer design for DC/DC power converters with bilinear averaged model

    NARCIS (Netherlands)

    Spinu, V.; Dam, M.C.A.; Lazar, M.

    2012-01-01

    Increased demand for high bandwidth and high efficiency made full state-feedback control solutions very attractive to power-electronics community. However, full state measurement is economically prohibitive for a large range of applications. Moreover, state measurements in switching power converters

  3. A Feedback Passivation Design for DC Microgrid and Its DC/DC Converters

    Directory of Open Access Journals (Sweden)

    Feifan Ji

    2016-12-01

    Full Text Available There are difficulties in analyzing the stability of microgrids since they are located on various network structures. However, considering that the network often consists of passive elements, the passivity theory is applied in this paper to solve the above-mentioned problem. It has been formerly shown that when the network is weakly strictly positive real (WSPR, the DC microgrid is stable if all interfaces between the microgrid and converters are made to be passive, which is called interface passivity. Then, the feedback passivation method is proposed for the controller design of various DC–DC converters to achieve the interface passivity. The interface passivity is different from the passivity of closed-loop systems on which the passivity based control (PBC concentrates. The feedback passivation design is detailed for typical buck converters and boost converters in terms of conditions that the controller parameters should satisfy. The theoretical results are verified by a hardware-in-loop real-time labotray (RTLab simulation of a DC microgrid with four generators.

  4. Very High Frequency Resonant DC/DC Converters for LED Lighting

    DEFF Research Database (Denmark)

    Madsen, Mickey Pierre; Knott, Arnold; Andersen, Michael A. E.

    2013-01-01

    with 40 V input and 15 V output are made. The simulation shows possibility of achieving efficiency up to 87 % even with a HEXFET Power MOSFET. Three prototypes of the simulated converter are implemented showing good correlation with simulations. The prototypes have efficiencies up to 84 % and power...

  5. High Efficiency Non-isolated Three Port DC-DC Converter for PV-Battery Systems

    DEFF Research Database (Denmark)

    Tomas Manez, Kevin; Anthon, Alexander; Zhang, Zhe

    2016-01-01

    This paper presents a nonisolated Three Port Converter (TPC) with a unidirectional port for photovoltaic (PV) panels and a bidirectional port for energy storage. With the proposed topology single power conversion is performed between each port, so high efficiencies are obtained. A theoretical...

  6. Pole placement method of controlling chaos in DC-DC buck converters

    Institute of Scientific and Technical Information of China (English)

    Zou Yan-Li; Luo Xiao-Shu; Chen Guan-Rong

    2006-01-01

    Based on the mechanism for the generation of chaos in a buck converter, a pole placement method is proposed and applied to controlling the chaos in a circuit. The control circuit is designed and tested. Numerical calculation and circuit implementation demonstrate the validity of this chaos control method.

  7. Design of high efficiency dual-mode buck DC-DC converter

    Science.gov (United States)

    Xinquan, Lai; Huali, Zeng; Qiang, Ye; Huisen, He; Shasha, Zhang; Yuqing, Sun

    2010-11-01

    A buck DC—DC switching regulator with high efficiency is implemented by automatically altering the modulation mode according to load current, and it can operate with an input range of 4.5 to 30 V. At light load current, the converter operates in skip mode. The converter enters PWM mode operation with increasing load current. It reduces the switching loss at light load and standby state, which results in prolonging battery lifetime and stand-by time. Meanwhile, externally adjustable soft-start minimizes the inrush supply current and avoids the overshoot of output voltage at initial startup. The regulator is fabricated by a 0.6 μm CDMOS process. The test results show that, under the condition of 3.3 V output, the efficiency is up to 64% at 5 mA and the maximum efficiency is 95.5%.

  8. Optimal Control with Complete Load-Decoupled Design for the Buck DC-DC Switching Converter

    Institute of Scientific and Technical Information of China (English)

    Fei-Hu; Hsieh; Yau-Tarng; Juang

    2002-01-01

    This paper describes a new controller design procedure and turning method for the buck PWM DCDCswitching converter taking into consideration the equivalent series resistance of components. First, the linearoptimal feedback is designed by the LQR approach. Then the designed control law is implemented by aphase-lag lead controller incorporated with a complete load-decoupled PD compensator. The phase-lag lead controlleris tuned to achieve the optimal design based on the output error voltage directly, instead of using an estimator.With the proposed PD compensator, the converter is robust with respect to the load changes and parameterperturbations. We also provide the conditions for the robust stability assurance of the closed-loop system.

  9. The 25 kW resonant dc/dc power converter

    Science.gov (United States)

    Robson, R. R.

    1983-01-01

    The feasibility of processing 25-kW of power with a single, transistorized, series resonant converter stage was demonstrated by the successful design, development, fabrication, and testing of such a device which employs four Westinghouse D7ST transistors in a full-bridge configuration and operates from a 250-to-350 Vdc input bus. The unit has an overall worst-case efficiency of 93.5% at its full rated output of 1000 V and 25 A dc. A solid-state dc input circuit breaker and output-transient-current limiters are included in and integrated into the design. Full circuit details of the converter are presented along with the test data.

  10. Design and implementation of adaptive slope compensation in current mode DC-DC converter

    Energy Technology Data Exchange (ETDEWEB)

    Guo Zhongjie; Wu Longsheng; Liu Youbao, E-mail: guozhongjie4213@126.com [Xi' an Microelectronic Technology Institute, Xi' an 710054 (China)

    2010-12-15

    To improve the compensation for the inherent instability in a current mode converter, the adaptive slope compensation, giving attention to the problems of the traditional compensation on compensation accuracy, loading capability and turning jitter, is presented. Based on the analysis of current loop, by detecting the input and output voltage, converting the adaptive slope compensation current, the compensation of the current loop is optimized successfully. It can not only improve the compensation accuracy but also eliminate the over compensation, the turning jitter and the poor loading capability in the reported slope compensation. A power supply chip with adaptive slope compensation has been fabricated in a 0.35 {mu}m CMOS process. The measurement results show that the chip starts up and operates steadily with the constant current limit under conditions of 5 V input voltage, from 10% to 100% duty cycle. (semiconductor integrated circuits)

  11. Topological variations of the inverse dual converter for high-power dc-dc distribution systems

    Science.gov (United States)

    Ehsani, Mehrdad; Laskai, Laszlo

    New dc-to-dc converter topologies are presented which are suitable for high density high power supplies. Topological variations of the basic inverse dual converter (IDC) circuit such as the transformer coupled, the multiphase and the multipulse derivation of the single phase IDC have been analyzed and some simulation results have been presented. The single phase IDC offers a buck-boost operation over wide range without transformer, bidirectional power flow, and complementary commutation of the switches. The topologies examined in this paper have additional features such as lower device and component stresses, and smaller filter requirements, resulting in smaller size and weight. Some performance and possible applications are also examined. IDCs for serial and parallel power distribution, and ac tapping of the IDC are discussed.

  12. An Efficiency-Optimized Isolated Bidirectional DC-DC Converter with Extended Power Range for Energy Storage Systems in Microgrids

    Directory of Open Access Journals (Sweden)

    Xiaolong Shi

    2012-12-01

    Full Text Available This paper proposes a novel extended-single-phase shift (ESPS control strategy of isolated bidirectional full-bridge DC-DC converters (IBDCs which are a promising alternative as a power electronic interface in microgrids with an additional function of galvanic isolation. Based on the mathematical models of ESPS control under steady-state conditions, detailed theoretical and experimental analyses of IBDC under ESPS control are presented. Compared with conventional single-phase-shift (CSPS control, ESPS control can greatly improve the efficiency of IBDCs in microgrids through decreasing current stress and backflow power considerably over a wide input and output voltage range under light and medium loads. In addition, ESPS control only needs to adjust one single phase-shift angel to control transmission power, thus it retains implementation simplicity in comparison with dual-phase-shift (DPS control for microgrid applications. Furthermore, an efficiency-optimized modulation scheme based on ESPS and CSPS control is developed in the whole power range of IBDC for power distribution in microgrids. A 10 kW IBDC prototype is constructed and the experimental results validate the effectiveness of the proposed control strategy, showing that the proposed strategy can enhance the overall efficiency up to 30%.

  13. A Survey on Voltage Boosting Techniques for Step-Up DC-DC Converters

    DEFF Research Database (Denmark)

    Forouzesh, Mojtaba; Siwakoti, Yam Prasad; Gorji, Saman Asghari;

    2016-01-01

    , researches on new voltage boosting techniques are inevitable for various power converter applications. This can be achieved either by additional magnetic or by electric field storage elements with switching elements (switch and/or diode) in different configurations. Such combination of primary voltage...... boosting techniques and topologies are large, which at times may be confusing and difficult to follow/adapt for different applications. Considering these aspects and in order to make a clear sketch of the general law and framework of various voltage boosting techniques, this paper comprehensively reviews...... different voltage boosting techniques and categorizes them according to their circuit performance....

  14. Soft Switching Full-Bridge PWM DC/DC Converter Using Secondary Snubber

    Directory of Open Access Journals (Sweden)

    Jaroslav Dudrik

    2009-05-01

    Full Text Available A novel full-bridge PWM DC/DCconverter with controlled secondary side rectifier usingsecondary snubber is presented in this paper.Limitation of the circulating current as well as softswitching for all power switches of the inverter isachieved for full load range from no-load to shortcircuit by using controlled rectifier and snubber on thesecondary side. Phase shift PWM control strategy isused for the converter. The principle of operation isexplained and analyzed and the experimental resultson a 1kW, 50 kHz laboratory model of the converterare presented.

  15. Generalized computer-aided discrete time domain modeling and analysis of dc-dc converters

    Science.gov (United States)

    Lee, F. C.; Iwens, R. P.; Yu, Y.; Triner, J. E.

    1977-01-01

    A generalized discrete time domain modeling and analysis technique is presented for all types of switching regulators using any type of duty-cycle controller, and operating in both continuous and discontinuous inductor current. State space techniques are employed to derive an equivalent nonlinear discrete time model that describes the converter exactly. The system is linearized about its equilibrium state to obtain a linear discrete time model for small signal performance evaluations, such as stability, audiosusceptibility and transient response. The analysis makes extensive use of the digital computer as an analytical tool. It is universal, exact and easy to use.

  16. Complete bifurcation analysis of DC-DC converters under current mode control

    Science.gov (United States)

    Pikulin, D.

    2014-03-01

    The purpose of this research is to investigate to what extend application of novel method of complete bifurcation groups to the analysis of global dynamics of piecewise-smooth hybrid systems enables one to highlight new nonlinear effects before periodic and chaotic regimes. Results include the construction of complete one and two-parameter bifurcation diagrams, detection of various types of bifurcation groups and investigation of their interactions, localization of rare attractors, and the investigation of different principles of birth of chaotic attractors. Effectiveness of the approach is illustrated in respect to one of the most widely used switching systems-boost converter under current mode control operating in continuous current mode.

  17. Y-Source Boost DC/DC Converter for Distributed Generation

    DEFF Research Database (Denmark)

    Siwakoti, Yam P.; Loh, Poh Chiang; Blaabjerg, Frede

    2015-01-01

    unmatched by existing impedance networks. The proposed converter also has more variables for tuning the required gain and, hence, more degrees of freedom for meeting design constraints. These capabilities have been demonstrated by mathematical derivation and experimental testing. For the experiments, a 300......-W prototype has been built in the laboratory using silicon carbide devices for better efficiency. The prototype has been tested with a regulated power supply, before operating it with a high-temperature proton-exchange-membrane fuel cell. Results obtained confirm the practicality and performance...

  18. A variable step-down conversion ratio switched capacitor DC-DC converter for energy harvesting systems working in intermittent mode

    Institute of Scientific and Technical Information of China (English)

    Hao Wenhan; Jia Chen; Chen Hong; Zhang Chun; Wang Zhihua

    2009-01-01

    Energy harvesting systems stimulate the development of power management for low power consumption applications. Improving the converter efficiency of power management circuits has become a significant issue in energy harvesting system design. This paper presents a variable step-down conversion ratio switched capacitor (SC)DC-DC converter to advance the converter efficiency of charge on the stored capacitor in a wireless monitoring system of orthopedic implants. The converter is designed to work at 1 MHz switching frequency and achieves 15 to 2 V conversion. Measurement results show that the converter efficiency can reach 4:2% including all circuit power consumption, which is much higher than previous work.

  19. A variable step-down conversion ratio switched capacitor DC-DC converter for energy harvesting systems working in intermittent mode

    Energy Technology Data Exchange (ETDEWEB)

    Hao Wenhan; Jia Chen; Chen Hong; Zhang Chun; Wang Zhihua, E-mail: haowh04@mails.tsinghua.edu.c [Tsinghua National Laboratory for Information Science and Technology, Institute of Microelectronics, Tsinghua University, Beijing 100084 (China)

    2009-12-15

    Energy harvesting systems stimulate the development of power management for low power consumption applications. Improving the converter efficiency of power management circuits has become a significant issue in energy harvesting system design. This paper presents a variable step-down conversion ratio switched capacitor (SC) DC-DC converter to advance the converter efficiency of charge on the stored capacitor in a wireless monitoring system of orthopedic implants. The converter is designed to work at 1 MHz switching frequency and achieves 15 to 2 V conversion. Measurement results show that the converter efficiency can reach 42% including all circuit power consumption, which is much higher than previous work. (semiconductor integrated circuits)

  20. Micro-Fabrication and Circuit Optimization for Magnetic Components of High-Efficiency DC-DC Converters

    Science.gov (United States)

    Tian, Rui

    Magnetic components are essential parts of power converters. Inductors with magnetic cores are investigated. An eddy current loss model for pot-core inductors is developed with finite elemental analysis (FEA). The reliability of inductors using magnetic cores in a high-temperature environment is investigated. Working in up to 150°C circumstance for a short periods is not destructive for the inductors. Optimization of toroidal inductors in a DC-DC converter is investigated. Parasitic capacitance and the capacitive loss in toroidal inductors are modeled. Standard circuit optimization is performed to explore the energy conversion efficiency of the toroidal inductors. Thermal analysis, light-load efficiency and relative permeability of the toroidal inductor design are also investigated. The toroidal inductor can achieve about 85% efficiency for 3 A DC current and 1 W/mm2 power density. Inductor-only efficiency of toroidal inductors is investigated with revised model. At 100 MHz operating frequency, toroidal inductors can achieve more than 97% inductor efficiency with power density range of 0.7 W/mm2 to 6 W/mm2. The performance of our nanograngular magnetic core is dependent on the angle of the poling magnetic field compared to the field during operation. Experiments on a serious of samples show that the poling angle can deviate by up to 15 degrees from ideal with only a small penalty in performance. The field-angle experiment is intended to prove integrated toroidal inductor process possible. A magnetic fixture model is proposed for large-scale toroidal inductor processing.

  1. High-Efficiency Self-Adjusting Switched Capacitor DC-DC Converter with Binary Resolution

    CERN Document Server

    Kushnerov, Alexander

    2010-01-01

    Switched-Capacitor Converters (SCC) suffer from a fundamental power loss deficiency which make their use in some applications prohibitive. The power loss is due to the inherent energy dissipation when SCC operate between or outside their output target voltages. This drawback was alleviated in this work by developing two new classes of SCC providing binary and arbitrary resolution of closely spaced target voltages. Special attention is paid to SCC topologies of binary resolution. Namely, SCC systems that can be configured to have a no-load output to input voltage ratio that is equal to any binary fraction for a given number of bits. To this end, we define a new number system and develop rules to translate these numbers into SCC hardware that follows the algebraic behavior. According to this approach, the flying capacitors are automatically kept charged to binary weighted voltages and consequently the resolution of the target voltages follows a binary number representation and can be made higher by increasing t...

  2. Considerations of Physical Design and Implementation for 5 MHz-100 W LLC Resonant DC-DC Converters

    Directory of Open Access Journals (Sweden)

    Akinori Hariya

    2016-01-01

    Full Text Available Recently, high power-density, high power-efficiency, and wide regulation range isolated DC-DC converters have been required. This paper presents considerations of physical design and implementation for wide regulation range MHz-level LLC resonant DC-DC converters. The circuit parameters are designed with 3–5 MHz-level switching frequency. Also, the physical parameters and the size of the planar transformer are optimized by using derived equations and finite element method (FEM with Maxwell 3D. Some experiments are done with prototype LLC resonant DC-DC converter using gallium nitride high electron mobility transistors (GaN-HEMTs; the input voltage is 42–53 V, the reference output voltage is 12 V, the load current is 8 A, the maximum switching frequency is about 5 MHz, the total volume of the circuit is 4.1 cm3, and the power density of the prototype converter is 24.4 W/cc.

  3. Multiple low frequency dual reference PWM control of a grid connected photovoltaic three phase NPC inverter with DC/DC boost converter

    Directory of Open Access Journals (Sweden)

    Mechouma Rabiaa

    2014-01-01

    Full Text Available In recent years, power demand of industrial applications has increased significantly reaching some megawatts. The use of multilevel converters for applications of medium and high powers is proposed as a solution to drawback semiconductor technology. A multilevel converter not only achieves high power ratings, but also enables the use of renewable energy sources. Renewable energy sources such as photovoltaic can be easily interfaced to a multilevel converter system for a high power application. This paper presents the simulation study in Matlab/Simulink of a grid connected photovoltaic three phase Neutral Point Clamped (NPC inverter with DC/DC boost converter for constant and variable solar radiation.

  4. Application of bifurcation theory to current-mode controlled parallel-connected DC-DC boost converters with multi bifurcation parameters

    Energy Technology Data Exchange (ETDEWEB)

    Natsheh, Ammar N. [Faculty of Engineering, Al-Ahliyya Amman University, Post Code 19328 Amman (Jordan); Nazzal, Jamal M. [Faculty of Engineering, Al-Ahliyya Amman University, Post Code 19328 Amman (Jordan)]. E-mail: jnazzal@ammanu.edu.jo

    2007-08-15

    This work describes the bifurcational behavior of a modular peak current-mode controlled DC-DC boost converter with multi bifurcation parameters. The parallel-input/parallel-output converter consists of two identical boost circuits and operates in the continuous-current conduction mode (CCM). A nonlinear mapping in closed form is derived and bifurcation diagrams are generated using MATLAB. A comparison is made between the modular converter diagrams with those of the single boost converter. The effect of introducing mutual coupling between the inductors of the constituent modules is also addressed. Results are verified using the circuit analysis package PSPICE.

  5. Transient Performance Improvement Circuit (TPIC)s for DC-DC converter applications

    Science.gov (United States)

    Lim, Sungkeun

    of the slow inductor current slew rate which is determined by the input voltage, output voltage, and the inductance. The remaining inductor current in the power delivery path will charge the output capacitors and develop a voltage across the ESR. As a result, large output voltage spikes occur during load current transients. Due to their limited control bandwidth, traditional VRs can not sufficiently respond rapidly to certain load transients. As a result, a large output voltage spike can occur during load transients, hence requiring a large amount of bulk capacitance to decouple the VR from the load [2]. If the remaining inductor current is removed from the power stage or the inductor current slew rate is changed, the output voltage spikes can be clamped, allowing the output capacitance to be reduced. A new design methodology for a Transient Performance Improvement Circuit(TPIC) based on controlling the output impedance of a regulator is presented. The TPIC works in parallel with a voltage regulator (VR)'s ceramic capacitors to achieve faster voltage regulation without the need for a large bulk capacitance, and can serve as a replacement for bulk capacitors. The specific function of the TPIC is to mimic the behavior of the bulk capacitance in a traditional VRM by sinking and sourcing large currents during transients, allowing the VR to respond quickly to current transients without the need for a large bulk capacitance. This will allow fast transient response without the need for a large bulk capacitor. The main challenge in applying the TPIC is creating a design which will not interfere with VR operation. A TPIC for a 4 Switch Buck-Boost (4SBB) converter is presented which functions by con- trolling the inductor current slew rate during load current transients. By increasing the inductor current slew rate, the remaining inductor current can be removed from the 4SBB power delivery path and the output voltage spike can be clamped. A second TPIC is presented which is

  6. Dynamical and steady-state characteristics of DC motors powered by photovoltaic systems via DC-DC buck-boost switch mode converter

    Energy Technology Data Exchange (ETDEWEB)

    Widyan, M.S.

    2010-07-01

    Photovoltaic (PV) cells for powering direct current (DC) motors are designed to provide maximum output power at the rated conditions of the motors. This paper presented the dynamic and steady-state characteristics of DC shunt, series and permanent-magnet motors fed by PV cells via a DC-DC buck-boost (step up-step down) switch mode converter. It considered the nonlinearities of the output characteristics of the PV cells and that of the magnetization curve of the machines. In order to address the problem of voltage regulation of the PV cells and the variation in solar illumination, the duty cycle controls the output voltage of the DC-DC converter to maintain a fixed voltage across the terminals of the motors at any realistic loading conditions. In this study, the DC-DC buck-boost switch mode converter achieved a fixed voltage across the terminals of the motors and therefore good speed regulation under a wide range of loading conditions and solar intensities. The entire study was carried out using the Matrix Laboratory Program MATLAB{sup TM} software.

  7. A high reliable DC-DC converter for charging battery%一种蓄电池充电用高可靠性DC-DC变换器

    Institute of Scientific and Technical Information of China (English)

    陶艳

    2012-01-01

    介绍了一种能将直流高压电源变换为直流低压电源,并对蓄电池进行充电和管理的高可靠性的DC-DC变换器.详细说明了DC-DC变换器的技术参数、功能要求及插槽式模块化结构设计方法,着重阐述了开关电源模块的均流控制、充电管理功能及电路原理;归纳总结了变换器高可靠性的冗余设计及其相应保护功能.%A high reliable DC-DC converter which could transform DC high voltage power supply into DC low voltage power supply,charge and manage the battery was introduced in this paper.Its technical parameters,functional requirements and modular structure design method of slots were illustrated for the DC-DC converter,focusing on the load sharing,charging management and circuit theory of the switching power supply modules; the DC-DC converter reliability redundancy design and its corresponding protection were summarized.

  8. Interleaved Boost-Half-Bridge Dual–Input DC-DC Converter with a PWM plus Phase-Shift Control for Fuel Cell Applications

    DEFF Research Database (Denmark)

    Zhang, Zhe; Andersen, Michael A. E.

    2013-01-01

    This paper presents an isolated dual-input DC-DC converter with a PWM plus phase-shift control for fuel cell hybrid energy systems. The power switches are controlled by phase shifted PWM signals with a variable duty cycle, and thus the two input voltages as well as the output voltage can...... the performance of the proposed PWM converter. The principle of operation is analyzed and some design considerations are discussed. Simulation results using PLECS are given to verify the proposed analysis and design. An experimental converter prototype has been designed, constructed and tested in the laboratory...

  9. 电动汽车用数字型直流-直流转换器设计%Design of digital DC-DC converter for electric vehicles

    Institute of Scientific and Technical Information of China (English)

    滕聪; 黄金强; 禄盛; 黄智宇

    2012-01-01

    The electric vehicle may win an opportunity due to the pollution of traditional vehicles. The DC-DC converter is an important device for the popularity of electric vehicles, in order to absorb the advantages of digital converter and meet the requirement of wide-range input voltage, the concept of digital DC-DC converters for electric vehicle has been a research subject in EVs area. However, this method requires high dynamic response and wide-range input voltage. A two-stage DC-DC converter controlled by automotive MCU and software was presented, based on the simulation result of small-signal model. The component parameters and test results were described. The results show that the DC-DC converter controlled by digital chip is a real-time programmability, and can meet the requirements of electric vehicles.%随着传统汽车污染的不断增加,以电动汽车为代表的新能源汽车迎来了机遇.而直流-直流( DC-DC)转换器是电动汽车中不可缺少的一种装置.为了吸纳数字型转换器的优点,以及符合宽范围输入电压的要求,电动汽车中用数字型DC-DC转换器已经成为新能源汽车领域中一个热门研究.然而,这种方法需要快速的动态响应.因此,根据其小信号模型仿真结果设计了一个两级转换拓扑的DC-DC转换器,并且设计了基于汽车级数字芯片控制的硬件电路平台和软件算法程序,并给出了DC-DC转换器的元件参数及测试结果.结果表明由数字芯片控制的DC-DC转化器是实时可编程的,也满足汽车电子的要求.

  10. Design of Flyback DC/DC Converter by Using TOPSwitch%基于TOPSwitch的反激式DC/DC变换器设计

    Institute of Scientific and Technical Information of China (English)

    侯晓云

    2015-01-01

    开关电源以其体积小、效率高等优点被广泛应用于计算机等各类电子设备中,小型化是其发展趋势之一.DC/DC 变换器是开关电源的核心部分.设计了一种基于TOPSwitch的反激式DC/DC变换器,主要包括主电路、控制电路、反馈电路等部分.对电路进行了制作与测试.实验结果表明,电路输出电压稳定、结构简单、体积较小、简化了设计过程.%SMPS is widely applied in computers and other electric equipment, the advantage of which is its small size and high efficiency. The development trend of it is miniaturization. DC/DC converter is the core part of SMPS. A Flyback DC/DC converter using TOPSwitch is designed. Main circuit, control circuit and feedback circuit designs are included. The circuit is manufactured and tested. The experimental results show the output voltage is stable, the circuit is simple, the size is small and the design process is simplified.

  11. 采用LCD箝位电路的正激DC-DC变换器%A Forward DC-DC Converter with a LCD Clamp Circuit

    Institute of Scientific and Technical Information of China (English)

    王国礼; 金新民

    2000-01-01

    In this paper a forward DC-DC converter with a LCD clamp circuit is propsed. The core is reset through this simple clamp circuit, and the efficiency of the converter is improved due to avoiding the energy loss.%介绍了一种采用LCD箝位电路的正激DC-DC变换器,它以十分简单的电路结构实现了变压器铁心的磁通复位,并且避免了能量的损耗,提高了变换器的效率。

  12. Design of switching frequency of DC-DC switching converter%DC-DC开关变换器开关工作频率设计

    Institute of Scientific and Technical Information of China (English)

    皇金锋

    2011-01-01

    根据DC-DC型开关变换器的工作原理,以Buck型开关变换器为例,讨论了储能电感、滤波电容、输出纹波电压、变换器转换效率与全控型开关器件的工作频率之间的关系,为开关频率的选择提供了理论依据,并进行仿真验证,仿真结果与理论分析一致,表明了参数计算和选择的合理性.分析的方法和结论为其它类型的DC-DC开关变换器的开关管工作频率的分析和设计提供了有效的分析手段和方法,也为实际DC-DC开关变换器的设计和调试提供了新的思路.%According to the working principle of DC-DC switch converter, taking the Buck switch converter as an example, the relationship among the energy storage inductors, filter capacitors, output ripple voltage, the converter efficiency and the operating frequency of total control switch was discussed, which provided a theoretical basis for the choice of the switch frequency. The process was verified through the emulation. The simulation results and theoretical analysis shows that the parameter calculation and the choice is reasonable. The analysis method and the conclusion provide an effective method for the design and analysis of the other type DC-DC switch converter switching valve operating frequency, and also provide a new idea for the design and debugging of the actual DC-DC switch converter.

  13. Analysis of bi-directional piezoelectric-based converters for zero-voltage switching operation

    DEFF Research Database (Denmark)

    Ekhtiari, Marzieh; Zhang, Zhe; Andersen, Michael A. E.

    2016-01-01

    This paper deals with a thorough analysis of zerovoltage switching especially for bi-directional, inductorless, piezoelectric transformer-based switch-mode power supplies with a half-bridge topology. Practically, obtaining zero-voltage switching for all of the switches in a bi......-directional piezoelectric power converter is a difficult task. However, the analysis in this work will be convenient for overcoming this challenge. The analysis defines the zero-voltage region indicating the operating points whether or not soft switching can be met over the switching frequency and load range. For the first...... time, a comprehensive analysis is provided, which can be used as a design guideline for applying control techniques in order to drive switches in piezoelectric transformer-based converters. This study further conveys the proposed method to the region where all the switches can obtain soft switching...

  14. High Radiation Resistant DC-DC Converter Regulators for use in Magnetic fields for LHC High Luminosity Silicon Trackers

    CERN Document Server

    Dhawan, S; Tipton, P; Kierstead, J; Lynn, D; rescia, S; Weber, M

    2007-01-01

    For more efficient power transport to the electronics embedded inside large colliding beam detectors, we explore the feasibility of supplying higher DC voltage and using local DC-DC conversion to 1.3 V (or lower, depending upon on the lithography of the embedded electronics) using switch mode regulators located very close to the front end electronics. These devices will be exposed to high radiation and high magnetic fields, 10 – 100 Mrads and 2 - 4 Tesla at the SLHC.

  15. A three-phase current-fed dc/dc converter with a three-leg high frequency transformer for fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Cha, Hanju [Department of Electrical Engineering, Chungnam National University, 220 Gung-dong Yuseong-gu, Daejeon 305-764 (Korea); Choi, Jungwan [National Fusion Research Institute, Daejeon (Korea); Enjeti, Prasad [Texas A and M University, College Station, TX 77843-3128 (United States)

    2008-07-15

    In this paper, a three-phase current-fed dc/dc converter with an active clamp is introduced, and a new three-phase three-leg high frequency transformer is proposed for the converter. The three-phase dc/dc converter transfers power through transformer leakage inductances in the discontinuous current mode; a single common active clamp branch is employed for zero-voltage switching (ZVS) in all active switches. Further, the converter's three-phase power configuration increases power transfer, and it reduces the rms current per phase, thus reduces conduction losses. Moreover, a delta-delta connection on the three-phase transformer provides parallel current paths and reduces conduction losses in the transformer windings. A three-phase transformer can be constructed by connecting three discrete single-phase transformers, but this process results in a higher volume and higher material costs. Therefore, a new three-phase three-leg high frequency transformer is designed with three discrete cores integrated into a single transformer core. The proposed transformer is analyzed according to the several operating modes of the converter, and its design rules are determined. Experimental results are obtained on a 500-W prototype unit; the design is fully verified and analyzed. (author)

  16. Digital DC-DC Converter Based on Buck-Boost Topology%基于Buck Boost拓扑的数字DC DC变换器设计

    Institute of Scientific and Technical Information of China (English)

    杜英; 郝茂森

    2014-01-01

    针对常规DC DC变换器输出电压调整困难、反馈实现复杂、智能化程度低的问题,提出了一种新型的能够根据用户要求快速改变输出电压的DC DC变换器,并且能够根据电源输入的电压变化情况实时调整控制参数,实现稳定的电压输出,且输出电压不受输入电压变化的影响。通过对不同负载和电源输入变化的实验验证,该DC DC变换器具有输出电压稳定精确、纹波率小、反馈快速准确的特点,对于某些对输入电压稳定性要求高的场合有实际应用意义。%Against the fact that the voltage values of DC-DC converter is difficult to adjust due to complex feedback and low degree of in-telligence,this paper proposes a new type of DC-DC converter that can be adjusted easily.This converter can adjust the control parame-ters along with the input voltage,keeping the output voltage stable.Experiments of different loads and input voltage show that this DC-DC converter has the advantage of stable output voltage,low voltage fluctuation,quick and accurate feedback.It has practical meaning in terms of requiring stable output voltage.

  17. Optimization of the design of DC-DC converters for improving the electromagnetic compatibility with the Front-End electronic for the super Large Hadron Collider Trackers

    CERN Document Server

    Fuentes Rojas, Cristian Alejandro; Blanchot, G

    2011-01-01

    The upgrade of the Large Hadron Collider (LHC) experiments at CERN sets new challenges for the powering of the detectors. One of the powering schemes under study is based on DC-DC buck converters mounted on the front-end modules. The hard environmental conditions impose strict restrictions to the converters in terms of low volume, radiation and magnetic field tolerance. Furthermore, the noise emission of the switching converters must not affect the performance of the powered systems. A study of the sources and paths of noise of a synchronous buck converter has been made for identifying the critical parameters to reduce their emissions. As proof of principle, a converter was designed following the PCB layout considerations proposed and then used for powering a silicon strip module prototype for the ATLAS upgrade, in order to evaluate their compatibility.

  18. A fully on-chip three-terminal switched-capacitor DC-DC converter for low-voltage CMOS LSIs

    Science.gov (United States)

    Kojima, Yuta; Hirose, Tetsuya; Tsubaki, Keishi; Ozaki, Toshihiro; Asano, Hiroki; Kuroki, Nobutaka; Numa, Masahiro

    2016-04-01

    In this paper, we present a fully on-chip switched-capacitor DC-DC converter for low-voltage CMOS LSIs. The converter has three terminals of input, ground, and output, by developing control circuits with fully on-chip configuration. We employ an ultra low-power nanoampere bias current and voltage reference circuit to achieve ultra low-power dissipation of control circuits. It enables us to realize a highly efficient power conversion circuit at light-load-current applications. The converter achieves highly efficient and robust voltage conversion using a pulse frequency modulation control circuit and a start-up/fail-safe circuit. Measurement results demonstrated that the converter can convert a 3.0 V input into 1.2 V output successfully. The start-up and fail-safe operations were confirmed through the measurement. The efficiency was more than 50% in the range of 2-6 µA load current.

  19. A wide load range, multi-mode synchronous buck DC-DC converter with a dynamic mode controller and adaptive slope compensation

    Institute of Scientific and Technical Information of China (English)

    Zhang Chunhong; Yang Haigang; Richard Shi

    2013-01-01

    A synchronous buck DC-DC converter with an adaptive multi-mode controller is proposed.In order to achieve high efficiency over its entire load range,pulse-width modulation (PWM),pulse-skip modulation (PSM)and pulse-frequency modulation (PFM) modes were integrated in the proposed DC-DC converter.With a highly accurate current sensor and a dynamic mode controller on chip,the converter can dynamically change among PWM,PSM and PFM control according to the load requirements.In addition,to avoid power device damage caused by inrush current at the start up state,a soft-start circuit is presented to suppress the inrush current.Furthermore,an adaptive slope compensation (SC) technique is proposed to stabilize the current programmed PWM controller for duty cycle passes over 50%,and improve the degraded load capability due to traditional slope compensation.The buck converter chip was simulated and manufactured under a 0.35μm standard CMOS process.Experimental results show that the chip can achieve 79% to 91% efficiency over the load range of 0.1 to 1000 mA.

  20. Anti-radiation performance test of a DC/DC converter%DC/DC变换器抗辐射试验

    Institute of Scientific and Technical Information of China (English)

    侯伟; 姚雨迎; 卓林

    2011-01-01

    文章以ZHDC28S05/18W型数字化DC/DC变换器(额定输入28V,输出5V/3.6A)为例,制定了DC/DC变换器辐射总剂量和单粒子效应试验的方案并进行了摸底试验,根据试验结果更换了集成功率芯片LM2596-ADJ,使产品的抗辐射性能有了明显提高.%A test scheme for the total dose radiation and single event effect of DC/DC converters is made, and the corresponding test is carried out for the ZHDC28S05/18W digital DC/DC converter.According to the test result, LM2596-ADJ chip (an integrated power chip inside the converter) is replaced with another type of its kind, to greatly improve the converter's anti-radiation performance.

  1. Control of Parallel DC/DC Converters in DC Microgrid%直流微网中平行DC/DC变换器的控制

    Institute of Scientific and Technical Information of China (English)

    叶友泉; 杨冠鲁

    2016-01-01

    提出以多墙体光伏为研究对象的光伏直流微网系统。将在逆变器并联控制中广泛使用的下垂控制策略应用到平行DC/DC变换器的控制中,与电压、电流环构成三闭环控制,从而抑制平行DC/DC变换器之间的环流。通过Simulink 仿真分析,该方法能够实现直流母线电压的稳定及有效抑制各平行DC/DC变换器之间的环流。最后,在实验室搭建实验平台,验证该控制策略的可行性。%This article proposes a photovoltaic ( PV) DC microgrid system which employs multi-wall PV. In the DC microgrid, the droop control strategy widely used in parallel control of inverter is adopted for the control of parallel DC/DC converters, forming a triple-loop control together with voltage and current loops, which restrains the loop current between parallel DC/DC converters. Simulink simulation shows that, stable DC bus voltage and effective control over the loop current among parallel DC / DC converters can be achieved by this way. In the end, an experimental platform is built in the lab to verify the feasibility of this control strategy.

  2. Introduction of a current waveform, waveshaping technique to limit conduction loss in high-frequency dc-dc converters suitable for space power

    Science.gov (United States)

    Miller, Douglas P.

    1990-06-01

    Space power supply manufacturers have tried to increase power density and construct smaller, highly efficient power supplies by increasing switching frequency. Incorporation of a power MOSFET as a switching element alleviates switching loss. However, values of R sub DS(on) (drain-to-source resistance in the on-state) for MOSFET's are of such magnitude to produce greater on-state losses than an equivalent BJT operated in saturation. This research serves to introduce a design concept, pertinent to low-voltage relatively-high-current applications, that minimizes the peak current through the switching element in order to reduce average power loss. Basic waveforms produced by different PWM and resonant mode topologies were examined. Theoretical analysis reveals that a ramp-sine current waveform could cut conduction power loss by at least 18 percent over a conventional Buck switching converter. A 14V, 14W combination quasi-resonant Buck/ZCS, Quasi-Resonant Buck dc-dc converter with an unregulated input voltage of 28 V was built for simplicity to demonstrate one particular waveshaping technique. This converter represents a useful example of an actual circuit which is capable of producing the desired ramp-sine switch-current waveform. Final results confirm improvement in conduction loss enhancing existing power MOSFET technology for use in dc-dc power conversion.

  3. A Current-Mode Buck DC-DC Converter with Frequency Characteristics Independent of Input and Output Voltages Using a Quadratic Compensation Slope

    Science.gov (United States)

    Sai, Toru; Sugimoto, Yasuhiro

    By using a quadratic compensation slope, a CMOS current-mode buck DC-DC converter with constant frequency characteristics over wide input and output voltage ranges has been developed. The use of a quadratic slope instead of a conventional linear slope makes both the damping factor in the transfer function and the frequency bandwidth of the current feedback loop independent of the converter's output voltage settings. When the coefficient of the quadratic slope is chosen to be dependent on the input voltage settings, the damping factor in the transfer function and the frequency bandwidth of the current feedback loop both become independent of the input voltage settings. Thus, both the input and output voltage dependences in the current feedback loop are eliminated, the frequency characteristics become constant, and the frequency bandwidth is maximized. To verify the effectiveness of a quadratic compensation slope with a coefficient that is dependent on the input voltage in a buck DC-DC converter, we fabricated a test chip using a 0.18µm high-voltage CMOS process. The evaluation results show that the frequency characteristics of both the total feedback loop and the current feedback loop are constant even when the input and output voltages are changed from 2.5V to 7V and from 0.5V to 5.6V, respectively, using a 3MHz clock.

  4. Isolated Full Bridge Boost DC-DC Converter Designed for Bidirectional Operation of Fuel Cells/Electrolyzer Cells in Grid-Tie Applications

    DEFF Research Database (Denmark)

    Pittini, Riccardo; Zhang, Zhe; Andersen, Michael A. E.

    2013-01-01

    -dc converter (IFBBC) designed for this new application focusing on losses analysis. The system topology is briefly discussed and the major concerns related to the system, cells stacks and converter operating points are analyzed. The dc-dc converter losses are modeled and presented in detail; the analysis...... is validated on adc-dc converter prototype rated at 6 kW 30-80 V 0-80 A on the low voltage side and 700-800 V on the high voltage side (for a grid-tie application). The prototype is based on fully planar magnetic, Si MOSFETs, Si IGBTs and SiC diodes; efficiencies up to ~96.5% and ~97.8% were demonstrated...

  5. DC-DC converters for fuel cell systems. Analysis, comparision and evaluation of different concepts; Gleichspannungswandler fuer Brennstoffzellensysteme. Analyse, Vergleich und Bewertung unterschiedlicher Konzepte

    Energy Technology Data Exchange (ETDEWEB)

    Averberg, Andreas

    2009-07-01

    Fuel cells in the kW range have relatively high output currents and low output voltages, which strongly depend on the load. Furthermore, ripple currents have a negative impact on efficiency and lifetime of the cells. These characteristics have to be taken into consideration in the design process of a dc-dc converter for fuel cell applications. This work focuses on the investigation of voltage-fed, current-fed and two-stage converters, comparing them with respect to their suitability for the use in fuel cell systems. For this purpose, analytical calculations are given, completely describing the operating behaviour of each individual topology. As a consequence, it is possible to present the trend of characteristic values as e.g. rms currents in all devices and the magnetic stress in the inductive components, depending on topology and operating parameters. The impact of switching frequency, the transformer's leakage inductance and its winding ratio and the value of an optional input or output inductor is clearly and completely stated out. Furthermore, depending on the aforementioned papameters, the location of optimum efficiency can be specified for all operating conditions. The power losses can be divided into their single parts. In this way, an optimised converter design is provided. Due to the leakage inductance in combination with a high switching frequency, the transferable power is limited in the investigated one-stage converters. This can especially be noticed in low input voltage applications, as is the case in fuel cell systems. An analytical equation for the maximum power of each dc-dc converter is deduced. Base on the analytical investigations, a comparison of the different dc-dc converters is done. Assuming equal chip areas of the semiconductor devices, equal ripple currents at the input of each topology and with consideration of the overall installed size, the converter efficiencies are calculated for full load as well as for partial load. This

  6. Assessment of an Average Controller for a DC/DC Converter via Either a PWM or a Sigma-Delta-Modulator

    Directory of Open Access Journals (Sweden)

    R. Silva-Ortigoza

    2014-01-01

    Full Text Available Sliding mode control is a discontinuous control technique that is, by its nature, appropriate for controlling variable structure systems, such as the switch regulated systems employed in power electronics. However, when designing control laws based on the average models of these systems a modulator is necessary for their experimental implementation. Among the most widely used modulators in power electronics are the pulse width modulation (PWM and, more recently, the sigma-delta-modulator (Σ-Δ-modulator. Based on the importance of achieving an appropriate implementation of average control laws and the relevance of the trajectory tracking task in DC/DC power converters, for the first time, this research presents the assessment of the experimental results obtained when one of these controllers is implemented through either a PWM or a Σ-Δ-modulator to perform such a task. A comparative assessment based on the integral square error (ISE index shows that, at frequencies with similar efficiency, the Σ-Δ-modulator provides a better tracking performance for the DC/DC Buck converter. In this paper, an average control based on differential flatness was used to perform the experiments. It is worth mentioning that a different trajectory tracking controller could have been selected for this research.

  7. Application of MLCC in DC/DC Converter and Its Optimal Design%MLCC在DC/DC变换器中的应用和优化设计

    Institute of Scientific and Technical Information of China (English)

    尹华; 陈璞

    2011-01-01

    Parasitic effects and frequency characteristics of capacitors were analyzed, and effects of equivalent series resistance of capacitor on electrical performance and stability of DC/DC converters were investigated. Difference of multilayer ceramic capacitor (MLCC) from other types of capacitors in application to DC/DC converter were described. With a specific circuit as an example, optimal design of the circuit using MICC were discussed.%通过分析电容器的寄生效应和频率特性,研究电容器等效串联电阻对DC/DC变换器电性能和稳定性的影响;明确了多层陶瓷电容器(MLCC)在DC/DC变换器应用中与其他种类电容器的不同之处;并对多层陶瓷电容器的优化设计方法进行探讨,用具体电路说明了优化设计过程.

  8. Charge Pump DC-DC Converter and Its Application%电荷泵DC-DC转换器及其应用

    Institute of Scientific and Technical Information of China (English)

    李国厚; 冯启高

    2000-01-01

    介绍了电荷泵DC-DC转换器的一般结构、工作原理及性能特点。详细讨论了利用DC-DC转换器进行电源系统设计的方法并给出了应用实例。这类电源系统可广泛应用于对电源的体积及效率有较高要求的便携式仪器仪表和测控系统中。%The general structure, principle and features of charge pump DC-DC converter are introduced 3n this paper, and the disign method of power supply system by means of DC-DC converter is discussed in detail and practical application is also given. This kind is power supply system can be widely used in portable instruments and measuring and controlling system with special requirements.

  9. An on-die ultra-low voltage DC-DC step-up converter with voltage doubling LC-tank

    Science.gov (United States)

    Jayaweera, H. M. P. C.; Pathirana, W. P. M. R.; Muhtaroğlu, Ali

    2016-12-01

    In this paper we report the design, characterization and verification of a novel on-die ultra-low voltage DC-DC converter circuit for energy harvester applications in 0.18 µm complementary metal oxide semiconductor technology. The circuit self-starts, does not use off-chip components, and is thus suitable for use in highly integrated low cost systems. The first version of the design has a five-stage charge-pump stimulated by an oscillator with two center-tap inductors. It is validated on a test chip that this converter can boost 0.25 V-1.7 V for a 60 kΩ load with 15.5% maximum efficiency. The center-tap implementation leads to a 38% area reduction compared to the conventional four planar inductors. The proposed second version of the DC-DC design has a modified LC-tank with center-tap and planar hybrid inductors, which leads to a simulated step up from 0.2 V input to 1.65 V output for a 45 kΩ load with 35% maximum efficiency. The new boost implementation is hence expected to improve both power efficiency and output power capacity significantly compared to the first design, at a cost of a 31% layout area growth. The second revision in addition provides a 15% chip area reduction compared to the conventional four planar-inductor approach.

  10. Switching performance and efficiency investigation of GaN based DC-DC Buck converter for low voltage and high current applications

    Science.gov (United States)

    Alatawi, Khaled; Almasoudi, Fahad; Matin, Mohammad

    2016-09-01

    The Wide band-gap (WBG) materials "such as Silicon Carbide (SiC) and Gallium nitride (GaN)" based power switching devices provide higher performance capabilities compared to Si-based power switching devices. The wide band-gap materials based power switching devices outperform Si-based devices in many performance characteristics such as: low witching loss, low conduction loss, high switching frequencies, and high operation temperature. GaN based switching devices benefit a lot of applications such as: future electric vehicles and solar power inverters. In this paper, a DC-DC Buck converter based on GaN FET for low voltage and high current applications is designed and investigated. The converter is designed for stepping down a voltage of 48V to 12V with high switching frequency. The capability of the GaN FET based buck converter is studied and compared to equivalent SiC MOSFET and Si-based MOSFET buck converters. The analysis of switching losses and efficiency was performed to compare the performance capabilities of GaN FET, SiC MOSFET and Si-based MOSFET. The results showed that the overall switching losses of GaN FET are lower than that of SiC and Si-based power switching devices. Also, the performance capability of GaN devices with higher frequencies is studied. GaN devices with high frequencies will reduce the total size and the cost of the power converter. In Addition, the overall efficiency of the DC-DC Buck converter is higher with the GaN FET switching devices, which make it more suitable for low voltage and high current applications.

  11. Topologies Research of High Voltage and High Power DC/DC Converters Used in DC Grids%用于直流电网的高压大容量DC/DC变换器拓扑研究

    Institute of Scientific and Technical Information of China (English)

    魏晓光; 王新颖; 高冲; 张升

    2014-01-01

    随着世界范围内大力发展直流电网,作为直流电网中关键器件之一的高压大容量 DC/DC 变换器的研究尤为重要。针对目前关于DC/DC变换器研究主要集中于中低压小功率场合的现状,该文首先从多个角度对直流电网用的高压大容量DC/DC变换器进行了需求分析;其次,对现有文献中提出的适用于直流电网的 DC/DC 变换器拓扑进行了研究,并将输入端串联输出端串联(input-series output-series, ISOS)结构和低压 DC/DC 变换器相结合,提出了用于直流电网中输入端和输出端均为高电压场合的 ISOS 型 DC/DC变换器。比较分析了不同拓扑变换器的电压变比、开关器件的电气应力和故障处理能力等,为选择合适的高压大容量DC/DC变换器拓扑提供了依据。%ABSTRACT:As DC/DC converter is one of the most critical components in DC grids, the study of high voltage and high power DC/DC converter is increasingly important with the rapid development of DC grid all over the world. However, the study of DC/DC converter is mostly focused on low or middle voltage and low power applications. In this paper, the requirements of DC/DC Converters used in large DC grids are addressed firstly. And then possible DC/DC converter topologies are reviewed and input-series and output series DC/DC converter is proposed. Finally, in order to provide a basis for selecting suitable high voltage and high power converters in DC grids, the voltage stresses, voltage conversion ratios and fault management ability of different converters topologies are analyzed.

  12. Experimental research of heavy ion and proton induced single event effects for a Bi-CMOS technology DC/DC converter

    Science.gov (United States)

    Anlin, He; Gang, Guo; Shuting, Shi; Dongjun, Shen; Jiancheng, Liu; Li, Cai; Hui, Fan

    2015-11-01

    This paper tested and analyzed heavy ion and proton induced single event effects (SEE) of a commercial DC/DC converter based on a 600 nm Bi-CMOS technology. Heavy ion induced single event transients (SET) testing has been carried out by using the Beijing HI-13 tandem accelerator at China Institute of Atomic Energy. Proton test has been carried out by using the Canadian TRIUMF proton accelerator. Both SET cross section versus linear energy transfer (LET) and proton energy has been measured. The main study conclusions are: (1) the DC/DC is both sensitive to heavy ion and proton radiations although at a pretty large feature size (600 nm), and threshold LET is about 0.06 MeV·mg/cm2 (2) heavy ion SET saturation cross section is about 5 magnitudes order larger than proton SET saturation cross section, which is consistent with the theory calculation result deduced by the RPP model and the proton nuclear reaction model; (3) on-orbit soft error rate (SER) prediction showed, on GEO orbit, proton induced SERs calculated by the heavy ion derived model are 4-5 times larger than those calculated by proton test data.

  13. 高耐压重叠式反激DC-DC变换器设计%The Design of High Input-bus Voltage Flyback DC-DC Converters

    Institute of Scientific and Technical Information of China (English)

    赵伟光

    2001-01-01

    提出了一种高耐压重叠式反激DC-DC变换器拓扑,成功地解决了高输入母线电 压下低功率开关电源的设计问题。讨论了该拓扑的优点,给出了应用电路。%A topology of overlapping flyback DC-DC converter is proposed in this paper. By using this topology, the problem of designing the switched power converter in high input-bus voltage has been solved successfully. The advantages of this topology are discussed and some useful circuits are given as well.

  14. VLSI Hybrid DC-DC Regulator

    OpenAIRE

    Cosp Vilella, Jordi; Martínez García, Herminio

    2015-01-01

    Hybrid DC-DC regulators are structures that combine both a linear voltage regulator and a switching DC-DC converter. The main objective of this hybrid topology is to converge, in a single circuit topology, the best of both alternatives: a small voltage output ripple, which is a common characteristic of linear regulator circuits, and good energy efficiency, as in switching alternatives. While the linear regulator fixes the required output voltage to a fixed value with negligible steady-state r...

  15. Bi-directional two-dimensional/three-dimensional convertible integral imaging using scattering polarizer

    Science.gov (United States)

    Yeom, Jiwoon; Hong, Jisoo; Park, Soon-gi; Min, Sung-Wook; Lee, Byoungho

    2012-10-01

    A bi-directional 2D/3D convertible integral imaging system is proposed. Two optical modules composed of a scattering polarizer and a linear polarizer are adopted, and 2D or 3D mode operation is easily changed by converting polarization states of the projected images. In the 2D mode, the incident light is scattered at the scattering polarizer and the scattered light facing the lens-array is blocked, a 2D image is observable only at the same side as the projector. In the 3D mode, the incident light with the transmission polarization is directly projected onto a lens-array, and the 3D images are integrated. Our proposed system is able to display the 3D images as well as the 2D images for the observers who are placed in front and rear side of the system.

  16. Dual-Input Soft-Switched DC-DC Converter with Isolated Current-Fed Half-Bridge and Voltage-Fed Full-Bridge for Fuel Cell or Photovoltaic Systems

    DEFF Research Database (Denmark)

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2013-01-01

    This paper introduces a new zero-voltage-switching (ZVS) isolated DC-DC converter with two input ports which can be utilized in hybrid energy systems, for instance, in a fuel cell and super-capacitor system. By fully using two high frequency transformers, the proposed converter can effectively...

  17. Wide input high step-up isolated DC/DC converter%宽输入高增益隔离升压型DC/DC变换器

    Institute of Scientific and Technical Information of China (English)

    肖文英; 戴日光

    2012-01-01

    隔离升压型DC/DC变换器是一类可以将低压直流母线变换成高压直流母线并实现电气隔离的变换器的统称.该技术在新能源发电领域如燃料电池发电系统以及微逆变器系统中应用广泛,其研究热点是宽输入适应性、高增益和高效率功率变换.LLC谐振变换器很好地符合这些要求.为此,研究了基于全桥LLC谐振变换器的高增益隔离升压型DC/DC变换器,提出了单级式和两级式两种方案,单级式方案为输出稳压LLC谐振变换器,而两级式方案为Boost变换器级联输出不稳压LLC谐振变换器.分别提出了LLC谐振变换器在单级式和两级式方案中的基于最佳励磁电感的谐振腔参数设计方法,并且分别通过样机实验验证了所提出的设计方法的有效性.%The isolated step-up DC/DC converter is a kind of converter that can convert low DC voltage bus into high DC voltage bus and realize electrical isolation. This technology has been widely used in new energy generation, such as fuel cell power system and micro-inverter system. Its research focuses on wide input adaptation, high step-up and high efficiency power conversion. LLC resonant converter perfectly satisfies these requirements. For this reason, high step-up DC/DC converter based on full bridge LLC resonant converter was studied in this paper. Two structures were presented, namely, single-stage structure applying regulated LLC resonant converter and two-stage structure applying Boost converter cascaded unregulated LLC resonant converter. The design method of the resonant tank under different structures based on the optimal magnetizing inductance was proposed. Finally, the prototypes of regulated and unregulated LLC resonant converter were built to verify the verification of the proposed method.

  18. Design of Novel DC/DC Converter for Photovoltaic Power Generation System%光伏发电系统的新型DC/DC变换器设计

    Institute of Scientific and Technical Information of China (English)

    陈晓; 孙以泽; 徐洋; 孟婥

    2011-01-01

    Aiming at the problems of hard-switching loss and one-way saturation of transformer magnetic cores caused by inconsistency switching characteristic in traditional full-bridge DC/DC converter, a novel phase-shift ZVS full-bridge DC/DC converter used in photovoltaic power system is designed in this paper. The control circuit adopts double-loop feedback program with chip UC3875 and the driving circuit is composed of the dedicated driving integrated chip IR2110S. This converter can achieve soft-switching, reduce the switching losses and improve the system efficiency. Moreover, it eliminates the magnetic bias, and the work of the transformer flux density can approach the saturation point. Finally, a prototype is built for verifying the design reliability.%针对传统全桥DC/DC变换器存在的硬开关损耗和因开关管开关特性不一致使变压器原边磁芯单向饱和问题,设计了一种用于光伏发电系统中的移相ZVS全桥DC/DC变换器,控制电路采用基于芯片UC3875的双环反馈方案,驱动电路由专用驱动集成芯片IR2110S构成.不仅实现了开关管的软开关控制、降低开关损耗、提高系统效率,还可解决偏磁问题,使变压器的磁通密度工作接近于饱和点.实验样机的研制验证了设计的可靠性.

  19. A 0.04 mm (2) Buck-Boost DC-DC Converter for Biomedical Implants Using Adaptive Gain and Discrete Frequency Scaling Control.

    Science.gov (United States)

    George, Libin; Gargiulo, Gaetano Dario; Lehmann, Torsten; Hamilton, Tara Julia

    2016-06-01

    This paper presents the design of a reconfigurable buck-boost switched-capacitor DC-DC converter suitable for use in a wide range of biomedical implants. The proposed converter has an extremely small footprint and uses a novel control method that allows coarse and fine control of the output voltage. The converter uses adaptive gain control, discrete frequency scaling and pulse-skipping schemes to regulate the power delivered to a range of output voltages and loads. Adaptive gain control is used to implement variable switching gain ratios from a reconfigurable power stage and thereby make coarse steps in output voltage. A discrete frequency scaling controller makes discrete changes in switching frequency to vary the power delivered to the load and perform fine tuning when the output voltage is within 10% of the target output voltage. The control architecture is predominately digital and it has been implemented as part of a fully-integrated switched-capacitor converter design using a standard bulk CMOS 0.18 μm process. Measured results show that the converter has an output voltage range of 1.0 to 2.2 V, can deliver up to 7.5 mW of load power and efficiency up to 75% using an active area of only 0.04 mm (2), which is significantly smaller than that of other designs. This low-area, low-complexity reconfigurable power converter can support low-power circuits in biomedical implant applications.

  20. Determination of PV Generator I-V/P-V Characteristic Curves Using a DC-DC Converter Controlled by a Virtual Instrument

    Directory of Open Access Journals (Sweden)

    E. Durán

    2012-01-01

    Full Text Available A versatile measurement system for systematic testing and measurement of the evolution of the I-V characteristic curves of photovoltaic panels or arrays (PV generators is proposed in this paper. The measurement system uses a circuit solution based on DC-DC converters that involves several advantages relative to traditional methods: simple structure, scalability, fast response, and low cost. The measurement of the desired characteristics of PV generators includes high speed of response and high fidelity. The prototype system built is governed by a microcontroller, and experimental results prove the proposed measurement system useful. A virtual instrument (VI was developed for full system control from a computer. The developed system enables monitoring the suitable operation of a PV generator in real time, since it allows comparing its actual curves with those provided by the manufacturer.

  1. Electrochemical treatment of tannery effluent using a battery integrated DC-DC converter and solar PV power supply--an approach towards environment and energy management.

    Science.gov (United States)

    Iyappan, K; Basha, C Ahmed; Saravanathamizhan, R; Vedaraman, N; Tahiyah Nou Shene, C A; Begum, S Nathira

    2014-01-01

    Electrochemical oxidation of tannery effluent was carried out in batch, batch recirculation and continuous reactor configurations under different conditions using a battery-integrated DC-DC converter and solar PV power supply. The effect of current density, electrolysis time and fluid flow rate on chemical oxygen demand (COD) removal and energy consumption has been evaluated. The results of batch reactor show that a COD reduction of 80.85% to 96.67% could be obtained. The results showed that after 7 h of operation at a current density of 2.5 A dm(-2) and flow rate of 100 L h(-1) in batch recirculation reactor, the removal of COD is 82.14% and the specific energy consumption was found to be 5.871 kWh (kg COD)(-1) for tannery effluent. In addition, the performance of single pass flow reactors (single and multiple reactors) system of various configurations are analyzed.

  2. Efficiency and Cost Comparison of Si IGBT and SiC JFET Isolated DC/DC Converters

    DEFF Research Database (Denmark)

    Nielsen, Rasmus Ørndrup; Török, Lajos; Munk-Nielsen, Stig

    2013-01-01

    . An efficiency of above 97 % for the SiC JFET and over 90 % for the SI IGBT converter was measured. Cost differences between the two converters have been analyzed, showing that 772 days of operation are needed for the SiC converter costs to break even with the Si IGBT converter costs....

  3. 电压反馈型半桥DC-DC变换器动力学特性%Dynamical Characteristic for Voltage-Feedback Half-Bridge DC-DC Converter

    Institute of Scientific and Technical Information of China (English)

    袁臣虎; 万健如; 李光叶; 周海亮

    2012-01-01

    Voltage-feedback half-bridge DC-DC converter, namely VCHB DC-DC, a dominant component of SMPS system, has rich dynamical characteristic. For revealing internal relation between system stability and circuit parameters, VCHB DC-DC converter was studied in detail. According to practical closed-loop control logic, the general simulation model was set up by using the exact state equations. And the general discrete mathematical model was deduced by stroboscopic maps. Nonlinearity characteristic of VCHB DC-DC converter under different parameters was simulated and analyzed by numerical method. Experimental results show that VCHB DC-DC converter is sensitive to transformer ratio, filter capacitor, inductive storage and error scale factor, while it is not sensitive to changes in error integral coefficient and load. The research results could serve as guidance for circuit parameters selection in VCHB DC-DC converter application.%电压反馈型半桥DC-DC (VCHB DC-DC)变换器组成的开关电源系统是强非线性系统,为揭示其系统稳定性与电路参数之间的内在关系,对VCHB DC-DC变换器进行了研究.结合其实际闭环控制逻辑,利用VCHB DC-DC变换器精确状态方程,建立VCHB DC-DC变换器仿真模型,采用频闪映射对其状态变量进行离散迭代映射,推导其统一的离散数学模型.对不同参数下VCHB DC-DC变换器非线性特性进行仿真和数值分析,并进行相应实验验证.研究结果表明,变压器变比、滤波电容、储能电感和误差比例系数的改变对VCHB DC-DC变换器稳定性影响大,而误差积分系数和负载的变化对其影响较弱.研究成果可为VCHB DC-DC变换器实际应用时的电路参数选取提供指导.

  4. Study and Implementation of a Two-Phase Interleaved Bidirectional DC/DC Converter for Vehicle and DC-Microgrid Systems

    Directory of Open Access Journals (Sweden)

    Ching-Ming Lai

    2015-09-01

    Full Text Available The objective of this paper is to implement a two-phase, interleaved, bidirectional DC/DC converter topology with an improved voltage conversion ratio for electric vehicle (EV and DC-microgrid systems. In this study, a two-phase interleaved charge-pump topology is introduced to achieve a high voltage conversion ratio with very simple control circuits. In discharge mode, the circuit topology acts as a voltage-multiplier boost converter to achieve a high step-up conversion ratio (48 V to 240 V. In charge mode, the circuit topology acts as a voltage-divider buck converter to achieve a high voltage step-down conversion ratio (240 V to 48 V. The circuit configuration, operating principle, steady-state analysis and the closed-loop control of the proposed converter are presented. Experiments conducted on a laboratory prototype with 500 W power-rating are presented to verify the effectiveness. The maximum efficiency levels in discharge and charge modes are about 97.7% and 98.4% respectively.

  5. Research on DC/DC converter of micro-inverter system%微逆变器系统的DC/DC变换器的研究

    Institute of Scientific and Technical Information of China (English)

    肖文英; 廖代文

    2012-01-01

    The DC/DC power conversion of micro-inverter system has the characteristics ot low input voltage, large input current, wide input voltage range and high output voltage. So DC/DC converter is required to have the characteristics of high step-up, high efficiency and wide input adaption by the micro-inverter system. LLC resonant converter perfectly satisfies these requirements. For this reason, digitally-controlled step-up LLC resonant converter applied in micro-inverter system was studied in this paper. The design method of the resonant tank based on optimal magnetizing inductance was proposed and digitally-controlled realization of LLC resonant converter was presented in detail using a kind of DSP chip named TMS320F28335. Finally, a three-hundred-watt prototype was build. The full load efficiency is 96.6% under rated input voltage together with 96.8% maximum value, and the full load efficiency reach above 96% under whole input range.%微逆变器系统中的DC/DC功率变换具有输入电压低且电压范围宽、输入电流大以及输出电压高的特点.因此微逆变器系统要求DC/DC变换器具有高升压比、高效率和宽输入范围适应性的特点.LLC谐振变换器很好地符合这些要求.为此,研究了应用于微逆变器系统的数字控制的升压型LLC谐振变换器,提出了基于最佳励磁电感的LLC谐振变换器谐振腔参数设计方法,采用TMS320F28335DSP芯片实现了LLC谐振变换器的数字控制,详细地给出了软件系统的实现方法.最后制作了一台300W样机,额定输入电压下满载效率为96.6%,最高效率达96.8%,全输入电压范围内满载效率在96%以上.

  6. Isolated DC-DC Converter for Bidirectional Power Flow Controlling with Soft-Switching Feature and High Step-Up/Down Voltage Conversion

    Directory of Open Access Journals (Sweden)

    Chih-Lung Shen

    2017-03-01

    Full Text Available In this paper, a novel isolated bidirectional DC-DC converter is proposed, which is able to accomplish high step-up/down voltage conversion. Therefore, it is suitable for hybrid electric vehicle, fuel cell vehicle, energy backup system, and grid-system applications. The proposed converter incorporates a coupled inductor to behave forward-and-flyback energy conversion for high voltage ratio and provide galvanic isolation. The energy stored in the leakage inductor of the coupled inductor can be recycled without the use of additional snubber mechanism or clamped circuit. No matter in step-up or step-down mode, all power switches can operate with soft switching. Moreover, there is a inherit feature that metal–oxide–semiconductor field-effect transistors (MOSFETs with smaller on-state resistance can be adopted because of lower voltage endurance at primary side. Operation principle, voltage ratio derivation, and inductor design are thoroughly described in this paper. In addition, a 1-kW prototype is implemented to validate the feasibility and correctness of the converter. Experimental results indicate that the peak efficiencies in step-up and step-down modes can be up to 95.4% and 93.6%, respectively.

  7. Interleaved soft-switched active-clamped L-L type current-fed half-bridge DC-DC converter for fuel cell applications

    Energy Technology Data Exchange (ETDEWEB)

    Rathore, Akshay K. [Electrical Machines and Drives Research Lab, University of Wuppertal, Rainer Gruenter Str. 21, University Campus Freudenberg, 42119 Wuppertal, NRW (Germany)

    2009-12-15

    In this paper, an interleaved soft-switched active-clamped L-L type current-fed half-bridge isolated dc-dc converter has been proposed. The L-L type active-clamped current-fed converter is able to maintain zero-voltage switching (ZVS) of all switches for the complete operating range of wide fuel cell stack voltage variation at full load down to light load conditions. Active-clamped circuit absorbs the turn-off voltage spike across the switches. Half-bridge topology maintains higher efficiency due to lower conduction losses. Soft-switching permits higher switching frequency operation, reducing the size, weight and cost of the magnetic components. Interleaving of the two isolated converters is done using parallel input series output approach and phase-shifted modulation is adopted. It reduces the input current ripple at the fuel cell input, which is required in a fuel cell system and also reduces the output voltage ripples. In addition, the size of the magnetic/passive components, current rating of the switches and voltage ratings of the rectifier diodes are reduced. (author)

  8. 双向全桥DC/DC转换器升降压控制系统的设计与实现%Design and realization of Boost-Buck control system for bidirectional full-bridge DC/DC converter

    Institute of Scientific and Technical Information of China (English)

    李宏恩; 周晋阳; 申玉坤

    2016-01-01

    双向DC/DC转换器是实现高低压电能双向传输功能的直流转换器,在各种直流稳压电源设计上应用广泛。通过小信号分析法,将非线性的DC/DC转换器变换为线性的数学模型进行研究,确定了全桥DC/DC转换器在升/降压模式下的传递函数,然后通过离散型PID控制算法,分析了系统控制的稳定性并确定了PID参数,设计了转换器补偿网络。最后通过仿真模型和样机实验验证,证明了双向全桥DC/DC转换器的升/降压控制系统的有效性。%The bidirectional DC/DC converter can realize the high voltage and low voltage bidirectional conversion,and is widely used in the design of various DC voltage⁃stabilized power supply. The nonlinear DC/DC converter is transformed into the linear mathematical model by means of the small signal analysis method for study. The transfer functions of full⁃bridge DC/DC converter in Boost/Buck modes are determined. And then the discrete PID control algorithm is used to analyze the stability of the control system and determine the PID parameters. The compensation network of the converter was designed. The simulation model and prototype experiment were verified,and the results show that the Boost⁃Buck control system of the bidirectional full⁃bridge DC/DC converter is effective.

  9. Design and research of multi-port DC/DC bidirectional converter based on super capacitor%基于超级电容双向多端口DC/DC变换器的设计与研究

    Institute of Scientific and Technical Information of China (English)

    薛迎春

    2015-01-01

    提出了基于超级电容的双向多端口DC/DC变换器设计方法。在常见的6种单管DC/DC变换器的开关管和二极管两端分别反向并联二极管和开关管,构成双向 DC/DC 变换器单元,以超级电容为各个变换器单元的连接枢纽,其两端电压作为直流母线电压,构成一个各个端口之间可以互相传递能量的双向多端口 DC/DC 变换器。在Matlab/Simulink环境下搭建变换器模型,仿真结果证明了双向多端口DC/DC变换器的可行性。%The objective is to propose an approach for multi-port DC/DC bidirectional converter based on super capacitor. The bidirectional DC/DC converter unit was based on the six normal DC/DC converters,through anti parallel diode and switch on the switch and diode respectively.Super capacitor is the connection point of the units, and the voltage of it is regarded as the DC bus voltage.Each port of the bidirectional converter unit can pass energy for each other.Finally, the simulation in Matlab verifies the performance of the proposed converter.

  10. Advanced High Power DC-DC Converter using A Novel Type Voltage Source Full-Bridge Soft-Switching PWM Inverter with High Frequency Transformer Link for Arc Welding Applications

    Science.gov (United States)

    Morimoto, Keiki; Doi, Toshimitsu; Manabe, Haruhiko; Ahmed, Tarek; Hiraki, Eiji; Lee, Hyun-Woo; Nakaoka, Mutsuo

    This paper presents a new circuit topology of full-bridge soft-switching PWM inverter linked DC-DC power converter composed of conventional full-bridge high frequency PWM inverter with high frequency transformer and an active quasi-resonant snubber consisting of an additional power switching device in series with DC busline and a lossless capacitor in parallel with DC busline. Under this proposed high frequency soft-switching PWM inverter linked DC-DC converter, four power switches in the full-bridge arms and DC busline series switch can achieve ZVS at turn-off commutation. By developing the advanced soft-switching PWM high frequency inverter type DC-DC converter, although the conduction power loss of DC busline series power switch increases a little, the total turn-off switching loss of full-bridge high frequency inverter power modules can be sufficiently lowered more and more in the higher frequency range of 60kHz. As a result, when the switching frequency of high frequency inverter power stage using IGBT power modules is designed so as to be more than about 10kHz, the more the switching frequency of inverter increases, the more this high frequency soft-switching DC-DC converter has remarkable advantage as for the power conversion efficiency as compared with the conventional hard-switching PWM inverter DC-DC converter. Its practical effectiveness of high power density and high performance is actually proved for TIG arc welding equipment in industry.

  11. Design of a High Voltage Bidirectional DC-DC Converter for Driving Capacitive Incremental Actuators usable in Electric Vehicles (EVs)

    DEFF Research Database (Denmark)

    Thummala, Prasanth; Zhang, Zhe; Andersen, Michael A. E.

    2014-01-01

    the converter for efficiently charging and discharging the capacitive actuator from 0 V to 2.5 kV and vice versa, respectively. The converter is used to drive a dielectric electro active polymer (DEAP) based capacitive incremental actuator, which has the potential to be used in automotive (e.g., EVs), space...

  12. Comparative Study on  Paralleled vs. Scaled Dc-dc Converters  in High Voltage Gain Applications

    DEFF Research Database (Denmark)

    Klimczak, Pawel; Munk-Nielsen, Stig

    2008-01-01

    's performance degradation or switches quick failure. A parallel modular converter built of many paralleled modules may be an interesting alternative, while a modular converter provides well known advantages like scalability, improved reliability and lower cost. This paper investigates possibility of improving...

  13. Thermal Modeling and Design of On-board DC-DC Power Converter using Finite Element Method

    DEFF Research Database (Denmark)

    Staliulionis, Zygimantas; Zhang, Zhe; Pittini, Riccardo;

    2014-01-01

    Power electronic converters are widely used and play a pivotal role in electronics area . The temperature causes around 54 % of all power converters failures. Thermal loads are nowadays one of the bottlenecks in the power system design and the cooling efficiency of a system is primarily determined...

  14. Thermal Modelling and Design of On-board DC-DC Power Converter using Finite Element Method

    DEFF Research Database (Denmark)

    Staliulionis, Z.; Zhang, Z.; Pittini, R.;

    2014-01-01

    Power electronic converters are widely used and play a pivotal role in electronics area. The temperature causes around 54 % of all power converters failures. Thermal loads are nowadays one of the bottlenecks in the power system design and the cooling efficiency of a system is primarily determined...

  15. Modeling and Dynamic Analysis of Paralleled dc/dc Converters With Master-Slave Current Sharing Control

    Science.gov (United States)

    Rajagopalan, J.; Xing, K.; Guo, Y.; Lee, F. C.; Manners, Bruce

    1996-01-01

    A simple, application-oriented, transfer function model of paralleled converters employing Master-Slave Current-sharing (MSC) control is developed. Dynamically, the Master converter retains its original design characteristics; all the Slave converters are forced to depart significantly from their original design characteristics into current-controlled current sources. Five distinct loop gains to assess system stability and performance are identified and their physical significance is described. A design methodology for the current share compensator is presented. The effect of this current sharing scheme on 'system output impedance' is analyzed.

  16. Modeling and Dynamic Analysis of Paralleled of dc/dc Converters with Master-Slave Current Sharing Control

    Science.gov (United States)

    Rajagopalan, J.; Xing, K.; Guo, Y.; Lee, F. C.; Manners, Bruce

    1996-01-01

    A simple, application-oriented, transfer function model of paralleled converters employing Master-Slave Current-sharing (MSC) control is developed. Dynamically, the Master converter retains its original design characteristics; all the Slave converters are forced to depart significantly from their original design characteristics into current-controlled current sources. Five distinct loop gains to assess system stability and performance are identified and their physical significance is described. A design methodology for the current share compensator is presented. The effect of this current sharing scheme on 'system output impedance' is analyzed.

  17. An integrated DC-DC step-up charge pump and step-down converter in 130 nm technology

    CERN Document Server

    Bochenek, M; Faccio, F; Kaplon, J

    2009-01-01

    After the LHC luminosity upgrade the number of readout channels in the ATLAS Inner Detector will be increased by one order of magnitude and delivering the power to the front-end electronics as well as cooling will become a critical system issue. Therefore a new solution for powering the readout electronics has to be worked out. Two main approaches for the power distribution are under development, the serial powering of a chain of modules and the parallel powering with a DCDC conversion stage on the detector. In both cases switchedcapacitor converters in the CMOS front-end chips will be used. In the paper we present the design study of a step-up charge pump and a step-down converter. In optimized designs power efficiency of 85 % for the step-up converter and 92 % for the step-down converter has been achieved.

  18. Design of DC-DC Converter and its Control for a Wind Generation System Connected to an Isolated Load

    Directory of Open Access Journals (Sweden)

    Carlos A. Ramírez Gómez

    2013-11-01

    Full Text Available A method to design a Buck converter and its control, which are associated to a wind generation system that is feeding an isolated load, is presented in this paper. To design the converter a Thevenin equivalent is deduced, which represents the behavior of the wind turbine, the permanent magnet synchronous generator, and the rectifier. The design of the converter elements guarantees input/output voltages and inductor current ripples of 5 % or less. The output voltage control is developed with a proportional-integral-derivative controller and as design criteria a damping of 0,707 and cutoff frequency of 1/5 converter commutation frequency are selected. The designed controller regulates the output voltage faced load perturbations and wind speed variations. 

  19. Non-Linear Behavioral Modeling for DC-DC Converters and Dynamic Analysis of Distributed Energy Systems

    OpenAIRE

    Xiancheng Zheng; Husan Ali; Xiaohua Wu; Haider Zaman; Shahbaz Khan

    2017-01-01

    In modern distributed energy systems (DES), focus is shifting from the conventional centralized approach towards distributed architectures. However, modeling and analysis of these systems is more complex, as it involves the interface of multiple energy sources with many different type of loads through power electronics converters. The integration of power electronics converters allows distributed renewable energy sources to become part of modern electronics power distribution systems (EPDS). ...

  20. The Influence of the Material of the Transformer Core on Characteristics of the Selected DC-DC Converters

    Science.gov (United States)

    Górecki, Krzysztof; Zarębski, Janusz

    In the paper the influence of the ferromagnetic material used for the construction of the core of the impulse-transformer on the characteristics of a half-bridge converter is considered. The investigated network is described and some results of measurements are shown. On the basis of the obtained characteristics of the investigated converters some suggestions for the designers of such circuits are formulated.

  1. A Low-Cost Soft-Switched DC/DC Converter for Solid-Oxide Fuel Cells

    Energy Technology Data Exchange (ETDEWEB)

    Jason Lai

    2009-03-03

    A highly efficient DC to DC converter has been developed for low-voltage high-current solid oxide fuel cells. The newly developed 'V6' converter resembles what has been done in internal combustion engine that split into multiple cylinders to increase the output capacity without having to increase individual cell size and to smooth out the torque with interleaving operation. The development was started with topology overview to ensure that all the DC to DC converter circuits were included in the study. Efficiency models for different circuit topologies were established, and computer simulations were performed to determine the best candidate converter circuit. Through design optimization including topology selection, device selection, magnetic component design, thermal design, and digital controller design, a bench prototype rated 5-kW, with 20 to 50V input and 200/400V output was fabricated and tested. Efficiency goal of 97% was proven achievable through hardware experiment. This DC to DC converter was then modified in the later stage to converter 35 to 63 V input and 13.8 V output for automotive charging applications. The complete prototype was tested at Delphi with their solid oxide fuel cell test stand to verify the performance of the modified DC to DC converter. The output was tested up to 3-kW level, and the efficiency exceeded 97.5%. Multiple-phase interleaving operation design was proved to be reliable and ripple free at the output, which is desirable for the battery charging. Overall this is a very successful collaboration project between the SECA Core Technology Team and Industrial Team.

  2. Posicast control within feedback structure for a DC-DC single ended primary inductor converter in renewable energy applications

    Energy Technology Data Exchange (ETDEWEB)

    Kalantar, M.; Mousavi G., S.M. [Center of Excellence for Power System Automation and Operation, Department of Electrical Engineering, Iran University of Science and Technology, Narmak, Tehran (Iran)

    2010-10-15

    In this paper, modeling, analysis, design, simulation and control of a single ended primary inductor converter (SEPIC) are discussed for renewable energy applications. Because the traditional control methods such as proportional-integral-derivative (PID) and classical half-cycle Posicast controllers based on feedforward are sensitive to noise and variations in natural frequency, a Posicast control with feedback structure is proposed and designed to reduce or rejection undesirable sensitivity greatly, to suppress measurement noise and to eliminate the overshoot in the output response. The SEPIC converter is modeled using average value modeling analysis. Dynamic modeling and simulation are accomplished using MATLAB Simulink trademark 7.2. (author)

  3. Research on Two-channel Interleaved Two-stage Paralleled Buck DC-DC Converter for Plasma Cutting Power Supply

    DEFF Research Database (Denmark)

    Yang, Xi-jun; Qu, Hao; Yao, Chen

    2014-01-01

    is selected as research subject, dedicated for the use of plasma cutting machine of 2×45kW, and the passivity-based control over the converter is analyzed theoretically at first, then simulated by means of MATLAB/SIMULINK, finally implemented on the modular product prototype. From the obtained results, it can...

  4. On the Development of High Power DC-DC Step-Down Converter with Energy Recovery Snubber

    Directory of Open Access Journals (Sweden)

    Alok Singh

    2012-01-01

    Full Text Available The effect of switching losses on the efficiency of a switch mode power converter and methods adopted for its improvement using an energy recovery lossless snubber has been presented. A comparative analysis of various types of soft switching techniques along with effects of dissipative and nondissipative snubbers on efficiency of the converter has been carried out before zeroing in on the selected scheme. The selected snubber serves the dual function of a turn-on and turn-off snubber and thereby reducing the switching losses both during turn-on and turn-off transients, resulting in improved efficiency of the converter. A detailed design procedure of the snubber for high-power applications taking into account various effects such as diode reverse recovery, diode voltage stress, and minimum and maximum duty cycle limits, has been presented in this paper. Importance of practical aspects in layout to minimize wiring inductance is also highlighted. A high-power prototype of buck converter has been developed to experimentally validate the theoretical design and analytical observations.

  5. Single-Event Transient Testing of the Crane Aerospace and Electronics SMHF2812D Dual DC-DC Converter

    Science.gov (United States)

    Casey, Megan

    2015-01-01

    The purpose of this testing was to characterize the Crane Aerospace & Electronics (Crane) Interpoint SMHF2812D for single-event transient (SET) susceptibility. These data shall be used for flight lot evaluation, as well as qualification by similarity of the SMHF family of converters, all of which use the same active components.

  6. Simplified loss analysis and comparison of full-bridge, full-range-ZVS DC-DC converters

    Indian Academy of Sciences (India)

    Shubhendu Bhardwaj; Mangesh Borage; Sunil Tiwari

    2008-10-01

    The loss of zero-voltage-switching (ZVS) of active switches has been a serious limitation of full-bridge (FBZVS) converters. Many techniques have been proposed in the past to extend the range of ZVS operation over the wider and also the full range of operation. However, in these techniques ZVS is achieved at the expense of additional conduction loss in active switches and losses in the auxiliary components. In this paper, the analysis for the additional losses in various full-range FBZVS DC–DC converters and their comparative evaluation is reported. Closed form expressions are derived for average value of device currents and losses. The loss curves for various topologies are plotted and compared. The analytical results are found to be consistent with the experimental efficiency tests performed on 500 W, 100 kHz prototype. It is concluded that a recently proposed new topology has the least penalty of additional losses.

  7. Multi-Purpose Low Voltage Dual Output DC-DC Converter For 100V Power Bus Telecom Platform

    Science.gov (United States)

    Galiana, D.; Mollard, J. M.

    2011-10-01

    The decreasing supply voltages of digital electronic and high speed ADC (Analog to Digital Converter) and DAC (Digital to Analog Converter) require flexible and high current secondary power distribution system. In the frame of the Inmarsat I-XL program, a 12 kW geomobile SatCom satellite, with 100 V regulated power bus, a multi purpose dual output converter was developed for the payload processor as a building block. After a short introduction on the main performance requirements, the baseline architecture is presented. The main drivers of the architecture are reliability, adjustability, radiation tolerant and single event free, volume and mass. The combination of all these constraints highlights the need of significant breakthrough in various domains. Many research results related to packaging and power electronic topics are brought up. These results directly drive the adopted solution presented in the next step followed by a description of the integration of the defined building block in the Inmarsat I-XL payload IP (Integrated Processor). Finally, the main electrical performances such as output ripple and spikes, load step transient and stability are summarized.

  8. Codimension-Two Big-Bang Bifurcation in a ZAD-Controlled Boost DC-DC Converter

    Science.gov (United States)

    Amador, A.; Casanova, S.; Granada, H. A.; Olivar, G.; Hurtado, J.

    In this paper, we study some nonlinear behaviors in a two-dimensional system defined by a Boost Converter controlled by CPWM (Centered Pulse-Width Modulation) and a ZAD (Zero Average Dynamics) strategy. The dynamics was analyzed using a discrete-time map, which consists of a sampled system at each switching cycle. The structure of the two-parametric space is characterized analytically. This allows proving the existence and stability of an infinite number of codimension-one curves that intersect at the same point in the two-parametric space. This phenomenon has been called a big-bang bifurcation.

  9. 超宽工作电压DC/DC变换器设计%Design of wide operating voltage DC/DC converter

    Institute of Scientific and Technical Information of China (English)

    王大为; 赵瑞杰; 陶学军; 田素立; 李朝锋

    2012-01-01

    Based on the situation of the wide output voltage range of solar photovoltaic power generation systems, a wide operating voltage of the DC / DC converter was designed. To solve the shortcoming of high voltage stress of the power when the switch was off, the voltage regulator tube was Introduced in order to clamp the voltage. To ensure the saturation switch conduction of the MOSFET, a rational circuit was designed to induce the current from the secondary circuit as the MOSFET gate driver. Based on the theoretical analysis, simulation and optimization, a 15 W, 1 000 V /200 V input prototype was designed.The test results show that the converter can work stably tor a long time.%针对太阳能光伏发电系统输出电压较宽的情况,设计了一种超宽工作电压的DC/DC变换器.利用稳压管在开关关断时对电路进行电压钳位,解决了单管反激变换器在高电压输入时电力MOSFET电压应力过高的缺陷.通过合理设计电路并从电路副边引入电流作为MOSFET栅极驱动,可以保证开关管的饱和导通.在理论分析、仿真优化、反复调试的基础上,设计了一款15W、1 000 V/200 V输入的样机.经过测试,此变换器可以长时间稳定工作且转换效率比较高.

  10. Design of isolated Buck-Boost DC/DC converter%Buck-Boost隔离直流转换器设计

    Institute of Scientific and Technical Information of China (English)

    王雪丹; 李文鹤

    2012-01-01

    在Buck-Boost隔离直流转换器宽范围输入电压的条件下,分析了典型的全桥Boost转换器拓扑结构,由于存在的谐振电感包括漏电感,全桥Boost转换器只能采用双边沿调制.该转换器采用UC3895作为控制器,对全桥单元采用移相转换控制的方式,为了提高全桥Boost转换器系统的可靠性和效率,采用三模式两频率控制方式,在输入宽范围电压的情况下,最高500 V输入,360 V输出.在此采用Matlab软件进行仿真,实验结果表明输入电压平均效率范围是96.2%,最高效率能达到97.5%.%The topology structure of a typical FB Boost converter was analyzed under the condition of wide range input voltage of isolated Buck-Boost DC/DC converter. The FB Boost converter can only adopt two-edge-modulation (TEM) due to the resonant induction including the leakage induction. The converter takes UC3895 available in market as the controller to control the FB-cell with phase-shifted. In order to improve the reliability and efficiency of the FB-Boost converter, a three-mode dual-frequency control mode was used. The maximum input voltage is 500 V and the output'is 360 V in the case of the wide range input voltage. The Matlab software was adopted for simulation. The result shows the the average efficiency range of the input-voltage is 96. 2% and the highest efficiency can reach to 97. 3%.

  11. Study on Test Method for Low Frequency Noise of Optoelectronic Coupled Device in DC/DC Converter%DC/DC电源用光电耦合器低频噪声测试方法研究

    Institute of Scientific and Technical Information of China (English)

    包军林; 孙明; 庄奕琪; 于鹏; 任泽亮

    2012-01-01

    Optoelectronic coupled device (OCD) is a key element of DC/DC converter. The random increase of low frequency noise (LFN) is one of the main failure modes of DC/DC converter. Effective test method and standard for LFN of photoelectric coupler are absent in China. In this paper, characteristics of low frequency noise in OCD and its generation mechanism were investigated in detail. Bias circuit, equipment and method for LFN measurement were proposed. Experimental results from OCD 4N47 in DC/DC converter demonstrated that the proposed method could be used for accurate measurement of low frequency noise of OCDs, providing an effective approach to evaluating typical faults and system suitability of optoelectronic coupler for DC/DC converter.%光电耦合器是DC/DC电源的关键器件,光电耦合器低频噪声的随机增大是该类电源主要失效模式之一.目前,国内尚未形成光电耦合器低频噪声的有效测试方法,更未建立相关标准.文章详细分析了光电耦合器低频噪声特性及产生机理,提出了其低频噪声测试的偏置电路、测试设备和测试方法.针对用于DC/DC电源的典型光电耦合器(4N47)的实测结果表明,该方法能够准确测试光电耦合器的低频噪声,为DC/DC电源用光电耦合器的系统适用性和典型故障提供了一种有效的评估方法.

  12. Design of a Miniaturized Dual Output DC/DC Converter%一种双路输出DC/DC变换器小型化设计

    Institute of Scientific and Technical Information of China (English)

    何颖; 李江达; 张晖

    2014-01-01

    Currently, the switch power supply to small, light weight and high efficiency characteristics are widely used in almost all electronic devices. Power systems are often referred to as"the heart of system"with other systems incomparable importance. With the development of science and technology, a variety of electrical equipment systems for the power supply are also increasing, power equipment system components directly affects the size, weight and reliability. In this paper, a miniaturized dual output isolated DC/DC converter as a design example, through the analysis of the actual circuit, a detailed description of its working principle and the main components of the value or calculation methods are also explainned.%目前,开关电源以小型、轻量和高效率等特点被广泛应用于几乎所有的电子设备,电源系统通常被称为“心脏系统”,有着其他系统不可比拟的重要地位。随着科学技术的发展,各种用电装备系统对于电源的要求也越来越高,电源组件直接影响着装备系统的体积、重量和可靠性。文章以一个小型化隔离型双路输出DC/DC变换器作为设计实例,通过对实际电路的分析,详细说明其工作原理及主要器件的取值或计算方法。

  13. DC-DC powering for the CMS pixel upgrade

    Science.gov (United States)

    Feld, Lutz; Fleck, Martin; Friedrichs, Marcel; Hensch, Richard; Karpinski, Waclaw; Klein, Katja; Rittich, David; Sammet, Jan; Wlochal, Michael

    2013-12-01

    The CMS experiment plans to replace its silicon pixel detector with a new one with improved rate capability and an additional detection layer at the end of 2016. In order to cope with the increased number of detector modules the new pixel detector will be powered via DC-DC converters close to the sensitive detector volume. This paper reviews the DC-DC powering scheme and reports on the ongoing R&D program to develop converters for the pixel upgrade. Design choices are discussed and results from the electrical and thermal characterisation of converter prototypes are shown. An emphasis is put on system tests with up to 24 converters. The performance of pixel modules powered by DC-DC converters is compared to conventional powering. The integration of the DC-DC powering scheme into the pixel detector is described and system design issues are reviewed.

  14. DC-DC Powering for the CMS Pixel Upgrade

    CERN Document Server

    Feld, Lutz Werner; Marcel Friedrichs; Richard Hensch; Karpinski, Waclaw; Klein, Katja; Rittich, David Michael; Sammet, Jan Domenik; Wlochal, Michael

    2013-01-01

    The CMS experiment plans to replace its silicon pixel detector with a new one with improved rate capability and an additional detection layer at the end of 2016. In order to cope with the increased number of detector modules the new pixel detector will be powered via DC-DC converters close to the sensitive detector volume. This paper reviews the DC-DC powering scheme and reports on the ongoing R and D program to develop converters for the pixel upgrade. Design choices are discussed and results from the electrical and thermal characterisation of converter prototypes are shown. An emphasis is put on system tests with up to24 converters. The performance of pixel modules powered by DC-DC converters is compared to conventional powering. The integration of the DC-DC powering scheme into the pixel detector is described and system design issues are reviewed.

  15. 高效率高增益Boost-Flyback直流变换器%High Efficiency High Step-up Boost-Flyback DC/DC Converter

    Institute of Scientific and Technical Information of China (English)

    吴红飞; 古俊银; 张君君; 邢岩; 陈国呈

    2011-01-01

    提出一种基于Boost拓扑与反激拓扑有机组合思想的Boost-Flyback变换器,Boost环节与反激环节共用输入支路,使电感一变压器的漏感能量得以利用,消除了漏感损耗,并实现了开关管电压钳位,减小了开关管电压应力;Boost与反激环节的输出支路串联,实现了高电压增益;Boost-Flybaek变换器输入并联输出串联,进一步提高了变换器的电压增益,同时减小了输入输出电压及电流纹波。提出新拓扑的DCM-ZVS工作模式控制方法,并在开环方式下实现了输出功率的控制。详细分析拓扑的工作原理、电压增益特性及控制方%A novel Boost-Flyback converter was proposed based on the combination of Boost and Flyback topologies. The energy stored in the leakage inductance of transformer is recycled and the active switch turn-off voltage is clamped by sharing the branch of the input side of the two topologies mentioned. High voltage gain is achieved with the output of Boost and Flyback topologies connected in series. The voltage gain of the converter is further improved with two of the Boost-Flybaek topologies proposed in input-in-parallel output-in-series connected. Devices stress, output and input voltage/current ripple are reduced. An output power control and discontinued current mode-zero voltage switching (DCM-ZVS) control were proposed also. The operational principle, voltage gain characteristics and principle of DCM-ZVS control method were analyzed in detail. The experimental results based on a 230 W 30 to 380 V DC/DC prototype verify the effectiveness of the theoretical analysis.

  16. Optimization of Inductance for Buck DC-DC Converter%Buck DC-DC变换器电感的优化设计

    Institute of Scientific and Technical Information of China (English)

    付园园; 姚素英; 徐江涛; 高静; 陈莞

    2012-01-01

    提出了一种优化电感的设计方法,以最小的电感实现了Buck DC-DC变换器最大输出纹波电压(MOVR)达到极小值.该方法首先通过计算得到连续导电模式(CCM)和不连续导电模式(DCM)下的输出纹波电压,然后根据电感取值分析这两种模式下的MOVR,最终得到了使MOVR达到极小值的最小电感.分析得到,对于任意给定的输入电压和负载范围,计算最大输入电压、最小负载下CCM和DCM模式的临界电感和最小输入电压、最大负载下的临界电感,则最优电感为两者中的较大值.Pspice仿真结果验证了上述理论分析的正确性,开关频率为52 kHz,输出电压12 V时,对于给定输入电压范围15~21V,负载范围35~170 Ω,最优电感为327μH.%In order to realize the lowest maximum output voltage ripple (MOVR) of Buck DC-DC converter with the minimal inductance, an optimal inductance design method is proposed. Output voltage, ripple (OVR) under continuous conduction mode (CCM) and discontinuous mode (DCM) was obtained by calculation, then MOVR in the two modes was analyzed according to the inductance value, and ultimately the minimum inductance to achieve the lowest MOVR was obtained. For any given range of the load and input voltage, by comparing the critical inductance between CCM and DCM under the maximum input voltage, minimum load condition and under the minimum input voltage, maximum load condition, it is concluded that the minimum inductance to guarantee the lowest MOVR is actually the maximum value of the critical inductance under the two conditions. The Pspice simulation results are in favor of the proposed theory.

  17. Two Quadrant DC/DC ZVS Quasi-Resonant Lou-Converter%一种两象限零电压开关准谐振DC-DC转换器设计

    Institute of Scientific and Technical Information of China (English)

    吴建忠; 张创; 刘迎迎

    2013-01-01

      传统的DC-DC转换器由电感、电容构成,通常电感和电容的面积很大,而且在开关导通和关断时的损耗严重。开关电感的两象限DC-DC转换器同时具有高功率密度和高转换效率,但是其开关导通和关断时的功率损耗仍然很严重。软开关技术可以实现开关导通和关断时的零功率损耗,从而大大减小了转换器的功率损耗。文章设计了一种新型的两象限零电压开关DC-DC转换器(ZVS-QRC),有效减小了功率损耗,并提高了功率密度和转换效率。%The classical DC/DC converters consist of inductors and capacitors, they usually are large and their power losses are high during switching-on and switching-off. A switched inductor DC/DC converter with two-quadrant operation can have characteristics of high power density and transfer efficiency. However, its power losses are still high during switching-on and switching-off. Soft switching technique implements the zero-power-consumption operation during switching-on and switching-off. Therefore, it largely reduces the power losses of the converter. This topic is a novel approach to investigate a two-quadrant DC/DC Zero-Voltage-Switching quasi-resonant converter (ZVS-QRC), which effectively reduces the power losses, and largely increases the power density and power transfer efficiency.

  18. 复合能源双向DC/DC变换器的建模与控制策略研究%Research on modeling and control strategy of bidirectional DC/DC converter for compound energy source

    Institute of Scientific and Technical Information of China (English)

    孟彦京; 李肖南

    2016-01-01

    提出一种基于超级电容的双向DC/DC变换器。根据DC/DC变换器的基本原理,在小信号假设条件下,采用状态空间平均法,建立变换器的数学模型;根据双向变换器的双向传递能量的工作原理,制定有效合理的控制策略;利用Mat⁃lab/Simulink库中超级电容模块搭建双向DC/DC变换器进行仿真,仿真和实验结果均表明,系统能够实现能量的双向传递,验证了其正确性和合理性。%A bidirectional DC/DC converter based on supercapacitor is proposed in this paper. According to the fundamen⁃tal principle of DC/DC converter,the state space average method is used to establish the mathematical model of the converter un⁃der the assumption of small signal. According to the working principle of bidirectional energy transfer of the bidirectional convert⁃er,the effective and reasonable control strategy was developed. A bidirectional DC/DC converter was built with the supercapaci⁃tor module in the Matlab/Simulink database to achieve simulation. The simulation and experimental results show that the system can transfer the energy bi⁃directionally,which verify its correctness and rationality.

  19. 基于群特性分析的DC-DC变换器级联系统稳定性判据%Stability Criterion about Cascaded System of DC-DC Converter Based on Their Group Characteristics

    Institute of Scientific and Technical Information of China (English)

    张波

    2012-01-01

    Stability analysis about cascaded system of power converters is an unsolved problem yet, the impedance ratio criteria applied in linear circuits is not suitable for analysis and study on cascaded systems of switched circuit. Therefore, this paper introduces group theory which researches symmetry into analysis of cascaded system of DC-DC converters, defines their group set, discusses their group characteristics, reveals the relationship and physical significance between their group and cascade characteristics. As a result, this paper develops a stability criterion about cascaded system of DC-DC converters based on group characteristics, gives a novel mathematical tool to solve stability problem of cascaded system of DC-DC converters.%电力电子变换器级联的稳定性分析是一个尚未解决的问题,线性电路的阻抗匹配规律不适合开关电路级联系统的分析和研究。为此,论文尝试将研究对称性的基本理论--群论引入到DC-DC变换器级联系统的分析中,试图根据DC-DC变换器级联系统的物理结构,定义基本DC-DC变换器级联系统的群集合.探讨它们的群特性,揭示群特性与级联特性之间的联系及物理意义,由此初步提出一个基于群特性分析的DC-DC变换器级联系统的稳定性判据,为解决DC-DC变换器级联的问题提供一个新的数学工具。

  20. Wind-Photovoltaic Hybrid Double-Input Buck-Boost DC/DC Converter%风光互补双输入Buck-Boost直流变换器的研究

    Institute of Scientific and Technical Information of China (English)

    廖志凌; 徐艳杰; 施卫东

    2014-01-01

    Instability and intermittency are two main drawbacks of independent solar energy generation. Therefore, it is essential to use a double-input DC/DC converter, which combines wind with solar to form a hybrid energy system. The paper proposes a new double-input Buck-Boost DC/DC converter with the following advantages: simple circuit, high voltage gain, and allowance of individual or simultaneous power delivery of the two sources. The operation principle of the double-input Buck-Boost DC/DC converter is analyzed, and the steady-state relation between convert input and output is presented. Finally, simulation results with PSPICE software are used to verify the theoretical analysis.%采用双输入直流变换器将太阳能和风能联合构成双输入供电系统,可避免独立光伏发电系统电力供应不稳定和不连续的缺点。本文提出一种新的双输入Buck-Boost直流变换器,具备电路结构简单、电压增益高特点,联合供电系统既可同时向负载供电,又可分体单独向负载供电。分析双输入Buck-Boost直流变换器的工作原理,给出变换器的输入/输出稳态关系式,并通过PSPICE软件进行仿真。仿真结果验证了理论分析的正确性。