WorldWideScience

Sample records for bet specific surface

  1. THE EFFECT OF STORAGE AT AMBIENT HUMIDITY ON THE BET-SPECIFIC SURFACE-AREA OF TABLETS COMPACTED FROM DIFFERENT MATERIALS

    NARCIS (Netherlands)

    RIEPMA, KA; DEKKER, BG; JAGER, RS; ELBERSE, PA; LERK, CF

    1993-01-01

    Tablets compacted from both water soluble and water insoluble particulate solids showed no change in BET-specific surface area when transferred immediately after ejection from the die in a dry atmosphere. Storage at ambient humidity resulted in an irreversible decrease in surface area, caused by

  2. The determination of specific surface of sodium polyuranates

    International Nuclear Information System (INIS)

    Bilgin, B.; Atun, G.

    2002-01-01

    Three different sodium polyuranates were prepared by titration of uranyl nitrate with a sodium hydroxide solution labeled with 22 Na as the radiotracer. Polyuranates whose composition was *Na 2 O.7,5UO 3 .11H 2 O (sample A), *Na 2 O.4,3 UO 3 .4,7H 2 O (sample B), and *Na 2 O.2UO 3 .4H 2 O (sample C) were precipitated at pH 5.6, 8.5 and 11.2, respectively. The specific surface areas of these samples were determined by the BET method using methylene blue (MB) as the adsorbate. The sodium polyuranate surfaces were saturated by sequential adsorption of MB. The adsorption data gave an S-shaped isotherm and were fitted to the BET equation. The specific surface areas calculated from the BET isotherm decreased in order A > B > C. The isotope and ion exchange reactions between the sodium polyuranates and Li + , Na + , K + , Rb + , Cs + , Ca 2+ , Sr 2+ , and Ba 2+ ions were compared before and after MB coverage. The results showed that the isotope and ion exchange fractions decrease on the covered surfaces indicating particle diffusion mechanism dominated exchange reactions

  3. BET measurements: Outgassing of minerals

    DEFF Research Database (Denmark)

    Clausen, Liselotte; Fabricius, Ida Lykke

    2000-01-01

    Outgassing minerals at elevated temperatures prior to BET measurements can lead to phase changes, especially in the case of amorphous and poorly crystalline materials. In order to evaluate the applicability of the BET method when low outgassing temperatures are required, selected aquifer minerals...... were outgassed at different temperatures and for different times. The studied minerals are 2-line ferrihydrite, goethite, lepidocrocite, quartz, calcite, ®-alumina, and kaolinite. The results demonstrate that measured specific surface areas of iron oxides are strongly dependent on outgassing conditions...... because the surface area increased by 170% with increasing temperature. In the poorly crystalline minerals, phase changes caused by heating were observed at temperatures lower than 100±C. Therefore low outgassing temperatures are preferable for minimizing phase changes. As demonstrated in this study...

  4. Chimeras of Bet v 1 and Api g 1 reveal heterogeneous IgE responses in patients with birch pollen allergy.

    Science.gov (United States)

    Gepp, Barbara; Lengger, Nina; Bublin, Merima; Hemmer, Wolfgang; Breiteneder, Heimo; Radauer, Christian

    2014-07-01

    Characterization of IgE-binding epitopes of allergens and determination of their patient-specific relevance is crucial for the diagnosis and treatment of allergy. We sought to assess the contribution of specific surface areas of the major birch pollen allergen Bet v 1.0101 to binding IgE of individual patients. Four distinct areas of Bet v 1 representing in total 81% of its surface were grafted onto the scaffold of its homolog, Api g 1.0101, to yield the chimeras Api-Bet-1 to Api-Bet-4. The chimeras were expressed in Escherichia coli and purified. IgE binding of 64 sera from Bet v 1-sensitized subjects with birch pollen allergy was determined by using direct ELISA. Specificity was assessed by means of inhibition ELISA. rApi g 1.0101, Api-Bet-1, Api-Bet-2, Api-Bet-3, and Api-Bet-4 bound IgE from 44%, 89%, 80%, 78%, and 48% of the patients, respectively. By comparing the amount of IgE binding to the chimeras and to rApi g 1.0101, 81%, 70%, 75%, and 45% of the patients showed significantly enhanced IgE binding to Api-Bet-1, Api-Bet-2, Api-Bet-3, and Api-Bet-4, respectively. The minority (8%) of the sera revealed enhanced IgE binding exclusively to a single chimera, whereas 31% showed increased IgE binding to all 4 chimeras compared with rApi g 1.0101. The chimeras inhibited up to 70% of IgE binding to rBet v 1.0101, confirming the specific IgE recognition of the grafted regions. The Bet v 1-specific IgE response is polyclonal, and epitopes are spread across the entire Bet v 1 surface. Furthermore, the IgE recognition profile of Bet v 1 is highly patient specific. Copyright © 2014 The Authors. Published by Mosby, Inc. All rights reserved.

  5. IgE and allergen-specific immunotherapy-induced IgG4 recognize similar epitopes of Bet v 1, the major allergen of birch pollen.

    Science.gov (United States)

    Groh, N; von Loetzen, C S; Subbarayal, B; Möbs, C; Vogel, L; Hoffmann, A; Fötisch, K; Koutsouridou, A; Randow, S; Völker, E; Seutter von Loetzen, A; Rösch, P; Vieths, S; Pfützner, W; Bohle, B; Schiller, D

    2017-05-01

    Allergen-specific immunotherapy (AIT) with birch pollen generates Bet v 1-specific immunoglobulin (Ig)G 4 which blocks IgE-mediated hypersensitivity mechanisms. Whether IgG 4 specific for Bet v 1a competes with IgE for identical epitopes or whether novel epitope specificities of IgG 4 antibodies are developed is under debate. We sought to analyze the epitope specificities of IgE and IgG 4 antibodies from sera of patients who received AIT. 15 sera of patients (13/15 received AIT) with Bet v 1a-specific IgE and IgG 4 were analyzed. The structural arrangements of recombinant (r)Bet v 1a and rBet v 1a _11x , modified in five potential epitopes, were analyzed by circular dichroism and nuclear magnetic resonance spectroscopy. IgE binding to Bet v 1 was assessed by ELISA and mediator release assays. Competitive binding of monoclonal antibodies specific for Bet v 1a and serum IgE/IgG 4 to rBet v 1a and serum antibody binding to a non-allergenic Bet v 1-type model protein presenting an individual epitope for IgE was analyzed in ELISA and western blot. rBet v 1a _11x had a Bet v 1a - similar secondary and tertiary structure. Monomeric dispersion of rBet v 1a _11x was concentration and buffer-dependent. Up to 1500-fold increase in the EC 50 for IgE-mediated mediator release induced by rBet v 1a _11x was determined. The reduction of IgE and IgG 4 binding to rBet v 1a _11x was comparable in 67% (10/15) of sera. Bet v 1a-specific monoclonal antibodies inhibited binding of serum IgE and IgG 4 to 66.1% and 64.9%, respectively. Serum IgE and IgG 4 bound specifically to an individual epitope presented by our model protein in 33% (5/15) of sera. Patients receiving AIT develop Bet v 1a-specific IgG 4 which competes with IgE for partly identical or largely overlapping epitopes. The similarities of epitopes for IgE and IgG 4 might stimulate the development of epitope-specific diagnostics and therapeutics. © 2016 John Wiley & Sons Ltd.

  6. The determination of surface of powders by BET method using nitrogen and krypton with computer calculation of the results

    International Nuclear Information System (INIS)

    Dembinski, W.; Zlotowski, T.

    1973-01-01

    A computer program written in FORTRAN language for calculations of final results of specific surface analysis based on BET theory has been described. Two gases - nitrogen and krypton were used. A technical description of measuring apparaturs is presented as well as theoretical basis of the calculations together with statistical analysis of the results for uranium compounds powders. (author)

  7. Thermal Desorption Analysis of Effective Specific Soil Surface Area

    Science.gov (United States)

    Smagin, A. V.; Bashina, A. S.; Klyueva, V. V.; Kubareva, A. V.

    2017-12-01

    A new method of assessing the effective specific surface area based on the successive thermal desorption of water vapor at different temperature stages of sample drying is analyzed in comparison with the conventional static adsorption method using a representative set of soil samples of different genesis and degree of dispersion. The theory of the method uses the fundamental relationship between the thermodynamic water potential (Ψ) and the absolute temperature of drying ( T): Ψ = Q - aT, where Q is the specific heat of vaporization, and a is the physically based parameter related to the initial temperature and relative humidity of the air in the external thermodynamic reservoir (laboratory). From gravimetric data on the mass fraction of water ( W) and the Ψ value, Polyanyi potential curves ( W(Ψ)) for the studied samples are plotted. Water sorption isotherms are then calculated, from which the capacity of monolayer and the target effective specific surface area are determined using the BET theory. Comparative analysis shows that the new method well agrees with the conventional estimation of the degree of dispersion by the BET and Kutilek methods in a wide range of specific surface area values between 10 and 250 m2/g.

  8. Betting exchanges : the future of sports betting?

    NARCIS (Netherlands)

    Koning, Ruud H.; Velzen, B. van

    Sports betting and sports have always been strongly connected. Traditionally, these betting markets have been cleared by bookmakers, who accept bets on certain events. These bookmakers carry the risk of paying the amount wagered if the event occurs. Recently, a new type of betting market has

  9. Risk Factors for Gambling Problems on Online Electronic Gaming Machines, Race Betting and Sports Betting.

    Science.gov (United States)

    Hing, Nerilee; Russell, Alex M; Browne, Matthew

    2017-01-01

    Growth of Internet gambling has fuelled concerns about its contribution to gambling problems. However, most online gamblers also gamble on land-based forms, which may be the source of problems for some. Studies therefore need to identify the problematic mode of gambling (online or offline) to identify those with an online gambling problem. Identifying most problematic form of online gambling (e.g., EGMs, race betting, sports betting) would also enable a more accurate examination of gambling problems attributable to a specific online gambling form. This study pursued this approach, aiming to: (1) determine demographic, behavioral and psychological risk factors for gambling problems on online EGMs, online sports betting and online race betting; (2) compare the characteristics of problematic online gamblers on each of these online forms. An online survey of 4,594 Australian gamblers measured gambling behavior, most problematic mode and form of gambling, gambling attitudes, psychological distress, substance use, help-seeking, demographics and problem gambling status. Problem/moderate risk gamblers nominating an online mode of gambling as their most problematic, and identifying EGMs ( n = 98), race betting ( n = 291) or sports betting ( n = 181) as their most problematic gambling form, were compared to non-problem/low risk gamblers who had gambled online on these forms in the previous 12 months ( n = 64, 1145 and 1213 respectively), using bivariate analyses and then logistic regressions. Problem/moderate risk gamblers on each of these online forms were then compared. Risk factors for online EGM gambling were: more frequent play on online EGMs, substance use when gambling, and higher psychological distress. Risk factors for online sports betting were being male, younger, lower income, born outside of Australia, speaking a language other than English, more frequent sports betting, higher psychological distress, and more negative attitudes toward gambling. Risk factors for

  10. Risk Factors for Gambling Problems on Online Electronic Gaming Machines, Race Betting and Sports Betting

    Directory of Open Access Journals (Sweden)

    Nerilee Hing

    2017-05-01

    Full Text Available Growth of Internet gambling has fuelled concerns about its contribution to gambling problems. However, most online gamblers also gamble on land-based forms, which may be the source of problems for some. Studies therefore need to identify the problematic mode of gambling (online or offline to identify those with an online gambling problem. Identifying most problematic form of online gambling (e.g., EGMs, race betting, sports betting would also enable a more accurate examination of gambling problems attributable to a specific online gambling form. This study pursued this approach, aiming to: (1 determine demographic, behavioral and psychological risk factors for gambling problems on online EGMs, online sports betting and online race betting; (2 compare the characteristics of problematic online gamblers on each of these online forms. An online survey of 4,594 Australian gamblers measured gambling behavior, most problematic mode and form of gambling, gambling attitudes, psychological distress, substance use, help-seeking, demographics and problem gambling status. Problem/moderate risk gamblers nominating an online mode of gambling as their most problematic, and identifying EGMs (n = 98, race betting (n = 291 or sports betting (n = 181 as their most problematic gambling form, were compared to non-problem/low risk gamblers who had gambled online on these forms in the previous 12 months (n = 64, 1145 and 1213 respectively, using bivariate analyses and then logistic regressions. Problem/moderate risk gamblers on each of these online forms were then compared. Risk factors for online EGM gambling were: more frequent play on online EGMs, substance use when gambling, and higher psychological distress. Risk factors for online sports betting were being male, younger, lower income, born outside of Australia, speaking a language other than English, more frequent sports betting, higher psychological distress, and more negative attitudes toward gambling. Risk

  11. IgE, IgG4 and IgA specific to Bet v 1-related food allergens do not predict oral allergy syndrome.

    Science.gov (United States)

    Guhsl, E E; Hofstetter, G; Lengger, N; Hemmer, W; Ebner, C; Fröschl, R; Bublin, M; Lupinek, C; Breiteneder, H; Radauer, C

    2015-01-01

    Birch pollen-associated plant food allergy is caused by Bet v 1-specific IgE, but presence of cross-reactive IgE to related allergens does not predict food allergy. The role of other immunoglobulin isotypes in the birch pollen-plant food syndrome has not been investigated in detail. Bet v 1-sensitized birch pollen-allergic patients (n = 35) were diagnosed for food allergy by standardized interviews, skin prick tests, prick-to-prick tests and ImmunoCAP. Concentrations of allergen-specific IgE, IgG1, IgG4 and IgA to seven Bet v 1-related food allergens were determined by ELISA. Bet v 1, Cor a 1, Mal d 1 and Pru p 1 bound IgE from all and IgG4 and IgA from the majority of sera. Immunoglobulins to Gly m 4, Vig r 1 and Api g 1.01 were detected in allergy and increased or reduced levels of IgE, IgG1, IgG4 or IgA specific to most Bet v 1-related allergens. Api g 1-specific IgE was significantly (P = 0.01) elevated in celeriac-allergic compared with celeriac-tolerant patients. Likewise, frequencies of IgE (71% vs 15%; P = 0.01) and IgA (86% vs 38%; P = 0.04) binding to Api g 1.01 were increased. Measurements of allergen-specific immunoglobulins are not suitable for diagnosing Bet v 1-mediated plant food allergy to hazelnut and Rosaceae fruits. In contrast, IgE and IgA to the distantly related allergen Api g 1 correlate with allergy to celeriac. © 2014 The Authors. Allergy Published by John Wiley & Sons Ltd.

  12. Surface Area Analysis Using the Brunauer-Emmett-Teller (BET) Method: Standard Operating Procedure Series: SOP-C

    Science.gov (United States)

    2016-09-01

    provide a foundational understanding of the steps involved, how to per- form them in a repeatable and reliable manner , and to provide the theory behind...how to perform them in a repeatable and reliable manner , and to provide the theory behind the analysis. 15. SUBJECT TERMS Surface area, BET

  13. Understanding Betting Strategy

    OpenAIRE

    Saha, Kanika; Lahiri, Ananya

    2017-01-01

    In this paper, we present betting strategy of a football game using probability theory. We know all betting houses offer slightly unfair odds towards the player. Here we discuss a simple way to figure out which betting house is offering relatively better odds compared to others for English Premier League. However, this methodology can be adopted for another league football match.

  14. Betting on conditionals

    OpenAIRE

    Politzer , Guy; Over , David P; Baratgin , Jean

    2010-01-01

    A study is reported testing two hypotheses about a close parallel relation between indicative conditionals, if A then B, and conditional bets, I bet you that if A then B. The first is that both the indicative conditional and the conditional bet are related to the conditional probability, P(B|A). The second is that de Finetti's three-valued truth table has psychological reality for both types of conditional – true, false, or void for indicative conditionals and win, lose or void for conditiona...

  15. A content analysis of how 'normal' sports betting behaviour is represented in gambling advertising

    OpenAIRE

    Lopez-Gonzalez, H; Guerrero-Solé, F; Griffiths, MD

    2017-01-01

    The pervasiveness of sports betting marketing and advertising is arguably normalising betting behaviour among increasingly larger groups of population. In their adverts, bookmakers represent characters and situations that conventionalise betting and promote specific behaviours while ignoring others. The present study examined a sample of British and Spanish sports betting television adverts (N=135) from 2014 to 2016 to understand how bettors and betting are being represented. Using content an...

  16. On the Spur of the Moment: Intrinsic Predictors of Impulse Sports Betting.

    Science.gov (United States)

    Hing, Nerilee; Li, En; Vitartas, Peter; Russell, Alex M T

    2018-06-01

    Betting on impulse, without thoughtful consideration, research or informed decision-making, may cause financial and other harms and lead to the development of gambling problems. Impulse betting undermines responsible consumption of gambling because it reflects self-regulatory failure, impaired control, unreflective decision-making and betting more than planned. In this paper we define impulse gambling and report on a study that aimed to understand more about the intrinsic characteristics of sports bettors who have a greater tendency to bet on impulse. Specifically, the study aimed to identify behavioural, psychological and socio-demographic predictors of impulse sports betting. A sample of 1816 Australian sports bettors completed an online survey that measured the proportion of their bets placed on impulse both before and during sporting events, as well as bets that were researched and planned in advance. Impulse betting was common, accounting for nearly one-half of all past-year sports bets by respondents. Over three-quarters of respondents had placed one or more impulse bets in the last year and one in seven respondents had made all of their sports bets on impulse. More impulsive sports bettors were characterised as having higher trait impulsiveness, higher problem gambling severity, more frequent sports betting and a shorter history of sports betting. They favoured betting on in-match contingencies instead of overall match outcomes. While health promotion strategies are needed to discourage impulse betting, research into contextual factors that arouse urges to bet would also provide direction for harm minimisation measures that help consumers to resist impulsive betting decisions.

  17. Isolation of Mal d 1 and Api g 1 - specific recombinant antibodies from mouse IgG Fab fragment libraries - Mal d 1-specific antibody exhibits cross-reactivity against Bet v 1.

    Science.gov (United States)

    Haka, Jaana; Niemi, Merja H; Iljin, Kristiina; Reddy, Vanga Siva; Takkinen, Kristiina; Laukkanen, Marja-Leena

    2015-05-27

    Around 3-5% of the population suffer from IgE-mediated food allergies in Western countries and the number of food-allergenic people is increasing. Individuals with certain pollen allergies may also suffer from a sensitisation to proteins in the food products. As an example a person sensitised to the major birch pollen allergen, Bet v 1, is often sensitised to its homologues, such as the major allergens of apple, Mal d 1, and celery, Api g 1, as well. Development of tools for the reliable, sensitive and quick detection of allergens present in various food products is essential for allergic persons to prevent the consumption of substances causing mild and even life-threatening immune responses. The use of monoclonal antibodies would ensure the specific detection of the harmful food content for a sensitised person. Mouse IgG antibody libraries were constructed from immunised mice and specific recombinant antibodies for Mal d 1 and Api g 1 were isolated from the libraries by phage display. More detailed characterisation of the resulting antibodies was carried out using ELISA, SPR experiments and immunoprecipitation assays. The allergen-specific Fab fragments exhibited high affinity towards the target recombinant allergens. Furthermore, the Fab fragments also recognised native allergens from natural sources. Interestingly, isolated Mal d 1-specific antibody bound also to Bet v 1, the main allergen eliciting the cross-reactivity syndrome between the birch pollen and apple. Despite the similarities in Api g 1 and Bet v 1 tertiary structures, the isolated Api g 1-specific antibodies showed no cross-reactivity to Bet v 1. Here, high-affinity allergen-specific recombinant antibodies were isolated with interesting binding properties. With further development, these antibodies can be utilised as tools for the specific and reliable detection of allergens from different consumable products. This study gives new preliminary insights to elucidate the mechanism behind the pollen

  18. Low-Risk Investing without Industry Bets

    DEFF Research Database (Denmark)

    Asness, Clifford S.; Frazzini, Andrea; Heje Pedersen, Lasse

    2014-01-01

    The strategy of buying safe low-beta stocks while shorting (or underweighting) riskier high-beta stocks (“betting against beta”) has been shown to deliver significant risk-adjusted returns. Some have suggested, however, that such “low-risk investing” delivers high returns primarily because...... of industry bets that favor a slowly changing set of stodgy, stable industries. The authors refute this notion by showing that a strategy of betting against beta has delivered positive returns both as an industry-neutral bet within each industry and as a pure bet across industries....

  19. Bookmaker and pari-mutuel betting

    DEFF Research Database (Denmark)

    Koch, Alexander; Shing, Hui-Fai

    2008-01-01

    A widely documented empirical regularity in gambling markets is that bets on high probability events (a race won by a "favourite") have higher expected returns than bets on low probability events (a "longshot" wins). Such favourite-longshot (FL) biases however appear to be more severe and persist......A widely documented empirical regularity in gambling markets is that bets on high probability events (a race won by a "favourite") have higher expected returns than bets on low probability events (a "longshot" wins). Such favourite-longshot (FL) biases however appear to be more severe...... and persistent in bookmaker markets than in pari-mutuel markets; the latter sometimes exhibit no bias or a reverse FL bias. Our results help understand these differences: the odds grid in bookmaker markets leads to a built-in FL bias, whereas that used in pari-mutuel betting pushes these markets toward a reverse...

  20. Betting patterns for sports and races: a longitudinal analysis of online wagering in Australia.

    Science.gov (United States)

    Gainsbury, Sally M; Russell, Alex

    2015-03-01

    Online wagering is increasing in popularity as it is easily accessible through websites which market these services widely. However, few studies have examined online betting based on actual behavioural data. This paper describes the results of an analysis of 2,522,299 bets placed with an Australian online wagering operator over a 1-year period. The majority of bets placed were for a win (45.31 %) and were placed on races (86.74 %) or sports (11.29 %). Sports betting was dominated by ball sports, reflecting popular interest in these events. More than three-quarters (77.63 %) of the bets were losses and there was large variation in bet size between bet types and events bet on although average bets were higher than in previously reported studies. The most popular bets placed to win, had a relatively high rate of losses and lowest average returns, which may reflect less sophisticated betting behaviour. More specific handicap and total bets were placed by fewer customers, but were larger bets with the greatest returns. Similarly, bets placed on less popular sporting events had greater average returns potentially reflecting greater customer sophistication and knowledge raising the possibility of a proportion of bettors being more 'skilled'. As the first paper to analyze the types of bets placed on events and outcomes the results support the notion that wagering is an entertainment activity, and the majority of customers are motivated by factors other than simply winning money.

  1. Betting is Loving and Bettors are Predators: A Conceptual Metaphor Approach to Online Sports Betting Advertising.

    Science.gov (United States)

    Lopez-Gonzalez, Hibai; Guerrero-Solé, Frederic; Estévez, Ana; Griffiths, Mark

    2017-10-30

    The legalisation of online gambling in multiple territories has caused a growth in the exposure of consumers to online sports betting (OSB) advertising. While some efforts have been made to understand the visible structure of betting promotional messages, little is known about the latent components of OSB advertisements. The present study sought to address this issue by examining the metaphorical conceptualisation of OSB advertising. A sample of Spanish and British television OSB advertisements from 2014 to 2016 was analysed (N = 133). Following Lakoff and Johnson's conceptual metaphor theory, four main structural metaphors that shaped how OSB advertising can be understood were identified: betting as (1) an act of love, (2) a market, (3) a sport, and (4) a natural environment. In general, these metaphors, which were found widely across 29 different betting brands, facilitated the perception of bettors as active players, with an executive role in the sport events bet upon, and greater control over bet outcomes.

  2. The Betting Odds Rating System: Using soccer forecasts to forecast soccer.

    Science.gov (United States)

    Wunderlich, Fabian; Memmert, Daniel

    2018-01-01

    Betting odds are frequently found to outperform mathematical models in sports related forecasting tasks, however the factors contributing to betting odds are not fully traceable and in contrast to rating-based forecasts no straightforward measure of team-specific quality is deducible from the betting odds. The present study investigates the approach of combining the methods of mathematical models and the information included in betting odds. A soccer forecasting model based on the well-known ELO rating system and taking advantage of betting odds as a source of information is presented. Data from almost 15.000 soccer matches (seasons 2007/2008 until 2016/2017) are used, including both domestic matches (English Premier League, German Bundesliga, Spanish Primera Division and Italian Serie A) and international matches (UEFA Champions League, UEFA Europe League). The novel betting odds based ELO model is shown to outperform classic ELO models, thus demonstrating that betting odds prior to a match contain more relevant information than the result of the match itself. It is shown how the novel model can help to gain valuable insights into the quality of soccer teams and its development over time, thus having a practical benefit in performance analysis. Moreover, it is argued that network based approaches might help in further improving rating and forecasting methods.

  3. The major birch pollen allergen Bet v 1 induces different responses in dendritic cells of birch pollen allergic and healthy individuals.

    Directory of Open Access Journals (Sweden)

    Ursula Smole

    Full Text Available Dendritic cells play a fundamental role in shaping the immune response to allergens. The events that lead to allergic sensitization or tolerance induction during the interaction of the major birch pollen allergen Bet v 1 and dendritic cells are not very well studied. Here, we analyzed the uptake of Bet v 1 and the cross-reactive celery allergen Api g 1 by immature monocyte-derived dendritic cells (iMoDCs of allergic and normal donors. In addition, we characterized the allergen-triggered intracellular signaling and transcriptional events. Uptake kinetics, competitive binding, and internalization pathways of labeled allergens by iMoDCs were visualized by live-cell imaging. Surface-bound IgE was detected by immunofluorescence microscopy and flow cytometry. Allergen- and IgE-induced gene expression of early growth response genes and Th1 and Th2 related cytokines and chemokines were analyzed by real-time PCR. Phosporylation of signaling kinases was analyzed by Western blot. Internalization of Bet v 1 by iMoDCs of both donor groups, likely by receptor-mediated caveolar endocytosis, followed similar kinetics. Bet v 1 outcompeted Api g 1 in cell surface binding and uptake. MoDCs of allergic and healthy donors displayed surface-bound IgE and showed a pronounced upregulation of Th2 cytokine- and NFκB-dependent genes upon non-specific Fcε receptor cross-linking. In contrast to these IgE-mediated responses, Bet v 1-stimulation increased transcript levels of the Th2 cytokines IL-4 and IL-13 but not of NFκB-related genes in MoDCs of BP allergic donors. Cells of healthy donors were either unresponsive or showed elevated mRNA levels of Th1-promoting chemokines. Moreover, Bet v 1 was able to induce Erk1/2 and p38 MAPK activation in BP allergics but only a slight p38 activation in normal donors. In conclusion, our data indicate that Bet v 1 favors the activation of a Th2 program only in DCs of BP allergic individuals.

  4. BET inhibition silences expression of MYCN and BCL2 and induces cytotoxicity in neuroblastoma tumor models.

    Directory of Open Access Journals (Sweden)

    Anastasia Wyce

    Full Text Available BET family proteins are epigenetic regulators known to control expression of genes involved in cell growth and oncogenesis. Selective inhibitors of BET proteins exhibit potent anti-proliferative activity in a number of hematologic cancer models, in part through suppression of the MYC oncogene and downstream Myc-driven pathways. However, little is currently known about the activity of BET inhibitors in solid tumor models, and whether down-regulation of MYC family genes contributes to sensitivity. Here we provide evidence for potent BET inhibitor activity in neuroblastoma, a pediatric solid tumor associated with a high frequency of MYCN amplifications. We treated a panel of neuroblastoma cell lines with a novel small molecule inhibitor of BET proteins, GSK1324726A (I-BET726, and observed potent growth inhibition and cytotoxicity in most cell lines irrespective of MYCN copy number or expression level. Gene expression analyses in neuroblastoma cell lines suggest a role of BET inhibition in apoptosis, signaling, and N-Myc-driven pathways, including the direct suppression of BCL2 and MYCN. Reversal of MYCN or BCL2 suppression reduces the potency of I-BET726-induced cytotoxicity in a cell line-specific manner; however, neither factor fully accounts for I-BET726 sensitivity. Oral administration of I-BET726 to mouse xenograft models of human neuroblastoma results in tumor growth inhibition and down-regulation MYCN and BCL2 expression, suggesting a potential role for these genes in tumor growth. Taken together, our data highlight the potential of BET inhibitors as novel therapeutics for neuroblastoma, and suggest that sensitivity is driven by pleiotropic effects on cell growth and apoptotic pathways in a context-specific manner.

  5. RVX-297- a novel BD2 selective inhibitor of BET bromodomains

    Energy Technology Data Exchange (ETDEWEB)

    Kharenko, Olesya A., E-mail: olesya@zenithepigenetics.com [Zenith Epigenetics, Suite 300, 4820 Richard Road SW, Calgary, Alberta, T3E 6L1 (Canada); Gesner, Emily M.; Patel, Reena G.; Norek, Karen [Zenith Epigenetics, Suite 300, 4820 Richard Road SW, Calgary, Alberta, T3E 6L1 (Canada); White, Andre; Fontano, Eric; Suto, Robert K. [Xtal BioStructures, Inc., 12 Michigan Dr., Natick, MA 01760 (United States); Young, Peter R.; McLure, Kevin G.; Hansen, Henrik C. [Zenith Epigenetics, Suite 300, 4820 Richard Road SW, Calgary, Alberta, T3E 6L1 (Canada)

    2016-08-12

    Bromodomains are epigenetic readers that specifically bind to the acetyl lysine residues of histones and transcription factors. Small molecule BET bromodomain inhibitors can disrupt this interaction which leads to potential modulation of several disease states. Here we describe the binding properties of a novel BET inhibitor RVX-297 that is structurally related to the clinical compound RVX-208, currently undergoing phase III clinical trials for the treatment of cardiovascular diseases, but is distinctly different in its biological and pharmacokinetic profiles. We report that RVX-297 preferentially binds to the BD2 domains of the BET bromodomain and Extra Terminal (BET) family of protein. We demonstrate the differential binding modes of RVX-297 in BD1 and BD2 domains of BRD4 and BRD2 using X-ray crystallography, and describe the structural differences driving the BD2 selective binding of RVX-297. The isothermal titration calorimetry (ITC) data illustrate the related differential thermodynamics of binding of RVX-297 to single as well as dual BET bromodomains. - Highlights: • A novel inhibitor of BET bromodomains, RVX-297 is described. • The differential binding modes of RVX-297 in BD1 and BD2 domains of BRD4 and BRD2 using X-ray crystallography are described. • RVX-297 preferentially binds to the BD2 domains of the BET bromodomains. • The structural and thermodynamic properties of the BD2 selective binding of RVX-297 are characterized.

  6. Gas adsorption on commercial magnesium stearate: Effects of degassing conditions on nitrogen BET surface area and isotherm characteristics.

    Science.gov (United States)

    Lapham, Darren P; Lapham, Julie L

    2017-09-15

    Commercial grades of magnesium stearate have been analysed by nitrogen adsorption having been pre-treated at temperatures between 30°C and 110°C and in the as-received state. Characteristics of nitrogen adsorption/desorption isotherms are assessed through the linearity of low relative pressure isotherm data and the BET transform plot together with the extent of isotherm hysteresis. Comparison is made between thermal gravimetric analysis and mass loss on drying. Features of gas adsorption isotherms considered atypical are identified and possible causes presented. It is shown that atypical isotherm features and issues of applying BET theory to the calculation of S BET are linked to the presence of hydrated water and that these depend on the hydration state: being more pronounced for the di-hydrate than the mono-hydrate. Dehydration reduces the extent of atypical features. S BET of a mono-hydrate sample is 5.6m 2 g -1 and 3.2m 2 g -1 at 40°C and 100°C degassing respectively but 23.9m 2 g 1 and 5.9m 2 g -1 for di-hydrate containing samples under comparable degassing. Di-hydrated samples also show S BET >15m 2 g 1 , BET C-values adsorption data. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. Costs, biases and betting markets: new evidence

    OpenAIRE

    Michael A. Smith; David Paton; Leighton Vaughan-Williams

    2004-01-01

    In recent years, person-to-person wagering on Internet ‘betting exchanges’ (sometimes known as ‘matched betting’) has become an increasingly important medium for betting on horse racing, sports and special events. Established gambling operators have argued that betting exchanges should not be allowed on the grounds that they represent unfair competition. In this paper, we argue that, in fact, betting exchanges have brought about reductions in traditional market biases and significant efficien...

  8. What do children observe and learn from televised sports betting advertisements? A qualitative study among Australian children.

    Science.gov (United States)

    Pitt, Hannah; Thomas, Samantha L; Bestman, Amy; Daube, Mike; Derevensky, Jeffrey

    2017-12-01

    To explore children's awareness of sports betting advertising and how this advertising may influence children's attitudes, product knowledge and desire to try sports betting. Semi-structured qualitative interviews were conducted with 48 children (8-16 years) from Melbourne, Victoria. The interview schedule explored children's recall and interpretations of sports betting advertising, strategies within advertisements that may appeal to children, children's product knowledge and understanding of betting terminology, and factors that may encourage gambling. Interviews were transcribed and thematic analysis was conducted. Children recalled in detail sports betting advertisements that they had seen, with humour the most engaging appeal strategy. They were also able to describe other specific appeal strategies and link these strategies to betting brands. Many children described how advertisements demonstrated how someone would place a bet, with some children recalling the detailed technical language associated with betting. Children had detailed recall of sports betting advertisements and an extensive knowledge of sports betting products and terminology. Implications for public health: To protect children from the potential harms associated with sports betting, governments should consider changing regulations and implementing evidence-based education campaigns to counter the positive messages children receive from the sports betting industry. © 2017 The Authors.

  9. BET bromodomain inhibition promotes neurogenesis while inhibiting gliogenesis in neural progenitor cells

    Directory of Open Access Journals (Sweden)

    Jingjun Li

    2016-09-01

    Full Text Available Neural stem cells and progenitor cells (NPCs are increasingly appreciated to hold great promise for regenerative medicine to treat CNS injuries and neurodegenerative diseases. However, evidence for effective stimulation of neuronal production from endogenous or transplanted NPCs for neuron replacement with small molecules remains limited. To identify novel chemical entities/targets for neurogenesis, we had established a NPC phenotypic screen assay and validated it using known small-molecule neurogenesis inducers. Through screening small molecule libraries with annotated targets, we identified BET bromodomain inhibition as a novel mechanism for enhancing neurogenesis. BET bromodomain proteins, Brd2, Brd3, and Brd4 were found to be downregulated in NPCs upon differentiation, while their levels remain unaltered in proliferating NPCs. Consistent with the pharmacological study using bromodomain selective inhibitor (+-JQ-1, knockdown of each BET protein resulted in an increase in the number of neurons with simultaneous reduction in both astrocytes and oligodendrocytes. Gene expression profiling analysis demonstrated that BET bromodomain inhibition induced a broad but specific transcription program enhancing directed differentiation of NPCs into neurons while suppressing cell cycle progression and gliogenesis. Together, these results highlight a crucial role of BET proteins as epigenetic regulators in NPC development and suggest a therapeutic potential of BET inhibitors in treating brain injuries and neurodegenerative diseases.

  10. Dependence of the specific surface area of the nuclear fuel with the matrix oxidation

    International Nuclear Information System (INIS)

    Gomez, F.; Quinones, J.; Iglesias, E.; Rodriguez, N.

    2008-01-01

    This paper is focused on the study of the changes in the specific surface area measured using BET techniques. The objective is to obtain a relation between this parameter and the change in the matrix stoichiometry (i.e., oxidation increase). None of the actual models used for extrapolating the behaviour of the spent fuel matrix under repository conditions have included this dependence yet. In this work the specific surface area of different uranium oxide were measured using N 2 (g) and Kr(g). The starting material was UO 2+x (s) with a size powder distribution lower than 20 μm. The results included in this paper shown a strong dependence on specific surface area with the matrix stoichiometry, i.e., and increase of more than one order of magnitude (SUO 2 = 6 m 2 *g -1 and SU 3 O 8 = 16.07 m 2 *g -1 ). Furthermore, the particle size distribution measured as a function of the thermal treatment done shows changes on the powder size related to the changes observed in the uranium oxide stoichiometry. (authors)

  11. DATA MINING IN SPORTS BETTING

    Directory of Open Access Journals (Sweden)

    Cristian Georgescu

    2013-12-01

    Full Text Available n this paper, we have made a brief analysis on how to make decisions in betting on European football with the help of data mining techniques. Whether you refer to betting a few days in advance of the sporting event or live betting, both options have been taken into consideration. By using a clustering algorithm for analyzing both the database containing events from football matches and the odds given by bookmakers, we have obtained graphs indicating the probabilities associated with analyzed events. Given the purely informative aspect of the current paper, we have only analyzed the number of corners from a match.

  12. BET Bromodomain Proteins Brd2, Brd3 and Brd4 Selectively Regulate Metabolic Pathways in the Pancreatic β-Cell.

    Directory of Open Access Journals (Sweden)

    Jude T Deeney

    Full Text Available Displacement of Bromodomain and Extra-Terminal (BET proteins from chromatin has promise for cancer and inflammatory disease treatments, but roles of BET proteins in metabolic disease remain unexplored. Small molecule BET inhibitors, such as JQ1, block BET protein binding to acetylated lysines, but lack selectivity within the BET family (Brd2, Brd3, Brd4, Brdt, making it difficult to disentangle contributions of each family member to transcriptional and cellular outcomes. Here, we demonstrate multiple improvements in pancreatic β-cells upon BET inhibition with JQ1 or BET-specific siRNAs. JQ1 (50-400 nM increases insulin secretion from INS-1 cells in a concentration dependent manner. JQ1 increases insulin content in INS-1 cells, accounting for increased secretion, in both rat and human islets. Higher concentrations of JQ1 decrease intracellular triglyceride stores in INS-1 cells, a result of increased fatty acid oxidation. Specific inhibition of both Brd2 and Brd4 enhances insulin transcription, leading to increased insulin content. Inhibition of Brd2 alone increases fatty acid oxidation. Overlapping yet discrete roles for individual BET proteins in metabolic regulation suggest new isoform-selective BET inhibitors may be useful to treat insulin resistant/diabetic patients. Results imply that cancer and diseases of chronic inflammation or disordered metabolism are related through shared chromatin regulatory mechanisms.

  13. BET Bromodomain Proteins Brd2, Brd3 and Brd4 Selectively Regulate Metabolic Pathways in the Pancreatic β-Cell.

    Science.gov (United States)

    Deeney, Jude T; Belkina, Anna C; Shirihai, Orian S; Corkey, Barbara E; Denis, Gerald V

    2016-01-01

    Displacement of Bromodomain and Extra-Terminal (BET) proteins from chromatin has promise for cancer and inflammatory disease treatments, but roles of BET proteins in metabolic disease remain unexplored. Small molecule BET inhibitors, such as JQ1, block BET protein binding to acetylated lysines, but lack selectivity within the BET family (Brd2, Brd3, Brd4, Brdt), making it difficult to disentangle contributions of each family member to transcriptional and cellular outcomes. Here, we demonstrate multiple improvements in pancreatic β-cells upon BET inhibition with JQ1 or BET-specific siRNAs. JQ1 (50-400 nM) increases insulin secretion from INS-1 cells in a concentration dependent manner. JQ1 increases insulin content in INS-1 cells, accounting for increased secretion, in both rat and human islets. Higher concentrations of JQ1 decrease intracellular triglyceride stores in INS-1 cells, a result of increased fatty acid oxidation. Specific inhibition of both Brd2 and Brd4 enhances insulin transcription, leading to increased insulin content. Inhibition of Brd2 alone increases fatty acid oxidation. Overlapping yet discrete roles for individual BET proteins in metabolic regulation suggest new isoform-selective BET inhibitors may be useful to treat insulin resistant/diabetic patients. Results imply that cancer and diseases of chronic inflammation or disordered metabolism are related through shared chromatin regulatory mechanisms.

  14. A mathematical analysis of an exchange-traded horse race betting fund with deterministic payoff betting strategy for institutional investment to challenge EMH

    Directory of Open Access Journals (Sweden)

    Craig George Leslie Hopf

    2015-12-01

    Full Text Available This paper’s primary alternative hypothesis is Ha: profitable exchange-traded horserace betting fund with deterministic payoff exists for acceptable institutional portfolio return—risk. The primary hypothesis challenges the semi-strong efficient market hypothesis applied to horse race wagering. An optimal deterministic betting model (DBM is derived from the existing stochastic model fundamentals, mathematical pooling principles, and new theorem. The exchange-traded betting fund (ETBF is derived from force of interest first principles. An ETBF driven by DBM processes conjointly defines the research’s betting strategy. Alpha is excess return above financial benchmark, and invokes betting strategy alpha that is composed of model alpha and fund alpha. The results and analysis from statistical testing of a global stratified data sample of three hundred galloper horse races accepted at the ninety-five percent confidence-level positive betting strategy alpha, to endorse an exchange-traded horse race betting fund with deterministic payoff into financial market.

  15. Biggest bets in the universe unveiled

    CERN Multimedia

    Jamieson, Valerie

    2004-01-01

    Betting on the greatest unsolved problems in the universe is no longer the preserve of academic superstars such as Stephen Hawking. From Thursday, anyone will be able to place bets on whether the biggest physics experiments in the world will come good before 2010

  16. Size-Dependent Specific Surface Area of Nanoporous Film Assembled by Core-Shell Iron Nanoclusters

    Directory of Open Access Journals (Sweden)

    Jiji Antony

    2006-01-01

    Full Text Available Nanoporous films of core-shell iron nanoclusters have improved possibilities for remediation, chemical reactivity rate, and environmentally favorable reaction pathways. Conventional methods often have difficulties to yield stable monodispersed core-shell nanoparticles. We produced core-shell nanoclusters by a cluster source that utilizes combination of Fe target sputtering along with gas aggregations in an inert atmosphere at 7∘C. Sizes of core-shell iron-iron oxide nanoclusters are observed with transmission electron microscopy (TEM. The specific surface areas of the porous films obtained from Brunauer-Emmett-Teller (BET process are size-dependent and compared with the calculated data.

  17. BET protein function is required for inflammation: Brd2 genetic disruption and BET inhibitor JQ1 impair mouse macrophage inflammatory responses.

    Science.gov (United States)

    Belkina, Anna C; Nikolajczyk, Barbara S; Denis, Gerald V

    2013-04-01

    Histone acetylation regulates activation and repression of multiple inflammatory genes known to play critical roles in chronic inflammatory diseases. However, proteins responsible for translating the histone acetylation code into an orchestrated proinflammatory cytokine response remain poorly characterized. Bromodomain and extraterminal (BET) proteins are "readers" of histone acetylation marks, with demonstrated roles in gene transcription, but the ability of BET proteins to coordinate the response of inflammatory cytokine genes through translation of histone marks is unknown. We hypothesize that members of the BET family of dual bromodomain-containing transcriptional regulators directly control inflammatory genes. We examined the genetic model of brd2 lo mice, a BET protein hypomorph, to show that Brd2 is essential for proinflammatory cytokine production in macrophages. Studies that use small interfering RNA knockdown and a small-molecule inhibitor of BET protein binding, JQ1, independently demonstrate BET proteins are critical for macrophage inflammatory responses. Furthermore, we show that Brd2 and Brd4 physically associate with the promoters of inflammatory cytokine genes in macrophages. This association is absent in the presence of BET inhibition by JQ1. Finally, we demonstrate that JQ1 ablates cytokine production in vitro and blunts the "cytokine storm" in endotoxemic mice by reducing levels of IL-6 and TNF-α while rescuing mice from LPS-induced death. We propose that targeting BET proteins with small-molecule inhibitors will benefit hyperinflammatory conditions associated with high levels of cytokine production.

  18. Halides of BET-TTF: novel hydrated molecular metals

    Energy Technology Data Exchange (ETDEWEB)

    Laukhina, E.; Ribera, E.; Vidal-Gancedo, J.; Canadell, E.; Veciana, J.; Rovira, C. [Universidad Autonoma de Barcelona, Bellaterra (Spain). Inst. de Ciencia de Materials; Khasanov, S.; Zorina, L.; Shibaeva, R. [Rossijskaya Akademiya Nauk, Chernogolovka (Russian Federation). Inst. Fiziki Tverdogo Tela; Laukhin, V. [Inst. of Problems of Chemical Physics, RAS, Chernogolovka (Russian Federation); Honold, M.; Nam, M.-S.; Singleton, J. [Clarendon Lab., Univ. of Oxford (United Kingdom)

    2000-01-07

    A hint of superconducting transition has been observed for the first time in a cation radical salt derived from bisethylenethio-tetrathiafulvalene (BET-TTF), the salt (BET-TTF){sub 2}Br.3H{sub 2}O. Here the synthesis, X-ray structure, and physical properties of two hydrated halides of BET-TTF that are isostructural and present stable metallic properties are described. (orig.)

  19. Heuristic and analytic processing in online sports betting.

    Science.gov (United States)

    d'Astous, Alain; Di Gaspero, Marc

    2015-06-01

    This article presents the results of two studies that examine the occurrence of heuristic (i.e., intuitive and fast) and analytic (i.e., deliberate and slow) processes among people who engage in online sports betting on a regular basis. The first study was qualitative and was conducted with a convenience sample of 12 regular online sports gamblers who described the processes by which they arrive at a sports betting decision. The results of this study showed that betting online on sports events involves a mix of heuristic and analytic processes. The second study consisted in a survey of 161 online sports gamblers where performance in terms of monetary gains, experience in online sports betting, propensity to collect and analyze relevant information prior to betting, and use of bookmaker odds were measured. This study showed that heuristic and analytic processes act as mediators of the relationship between experience and performance. The findings stemming of these two studies give some insights into gamblers' modes of thinking and behaviors in an online sports betting context and show the value of the dual mediation process model for research that looks at gambling activities from a judgment and decision making perspective.

  20. T-bet and Eomes are differentially linked to the exhausted phenotype of CD8+ T cells in HIV infection.

    Directory of Open Access Journals (Sweden)

    Marcus Buggert

    2014-07-01

    Full Text Available CD8(+ T cell exhaustion represents a major hallmark of chronic HIV infection. Two key transcription factors governing CD8(+ T cell differentiation, T-bet and Eomesodermin (Eomes, have previously been shown in mice to differentially regulate T cell exhaustion in part through direct modulation of PD-1. Here, we examined the relationship between these transcription factors and the expression of several inhibitory receptors (PD-1, CD160, and 2B4, functional characteristics and memory differentiation of CD8(+ T cells in chronic and treated HIV infection. The expression of PD-1, CD160, and 2B4 on total CD8(+ T cells was elevated in chronically infected individuals and highly associated with a T-bet(dimEomes(hi expressional profile. Interestingly, both resting and activated HIV-specific CD8(+ T cells in chronic infection were almost exclusively T-bet(dimEomes(hi cells, while CMV-specific CD8(+ T cells displayed a balanced expression pattern of T-bet and Eomes. The T-bet(dimEomes(hi virus-specific CD8(+ T cells did not show features of terminal differentiation, but rather a transitional memory phenotype with poor polyfunctional (effector characteristics. The transitional and exhausted phenotype of HIV-specific CD8(+ T cells was longitudinally related to persistent Eomes expression after antiretroviral therapy (ART initiation. Strikingly, these characteristics remained stable up to 10 years after ART initiation. This study supports the concept that poor human viral-specific CD8(+ T cell functionality is due to an inverse expression balance between T-bet and Eomes, which is not reversed despite long-term viral control through ART. These results aid to explain the inability of HIV-specific CD8(+ T cells to control the viral replication post-ART cessation.

  1. BET protein function is required for inflammation: Brd2 genetic disruption and BET inhibitor JQ1 impair mouse macrophage inflammatory responses1

    Science.gov (United States)

    Belkina, Anna C.; Nikolajczyk, Barbara S.; Denis, Gerald V.

    2013-01-01

    Histone acetylation regulates activation and repression of multiple inflammatory genes known to play critical roles in chronic inflammatory diseases. However, proteins responsible for translating the histone acetylation code into an orchestrated pro-inflammatory cytokine response remain poorly characterized. Bromodomain extra terminal (BET) proteins are “readers” of histone acetylation marks with demonstrated roles in gene transcription, but the ability of BET proteins to coordinate the response of inflammatory cytokine genes through translation of histone marks is unknown. We hypothesize that members of the BET family of dual bromodomain-containing transcriptional regulators directly control inflammatory genes. We examined the genetic model of brd2 lo mice, a BET protein hypomorph, to show that Brd2 is essential for pro-inflammatory cytokine production in macrophages. Studies that utilize siRNA knockdown and a small molecule inhibitor of BET protein binding, JQ1, independently demonstrate BET proteins are critical for macrophage inflammatory responses. Furthermore, we show that Brd2 and Brd4 physically associate with the promoters of inflammatory cytokine genes in macrophages. This association is absent in the presence of BET inhibition by JQ1. Finally, we demonstrate that JQ1 ablates cytokine production in vitro and blunts the “cytokine storm” in endotoxemic mice by reducing levels of IL-6 and TNF-α while rescuing mice from LPS-induced death. We propose that targeting BET proteins with small molecule inhibitors will benefit hyper-inflammatory conditions associated with high levels of cytokine production. PMID:23420887

  2. On the effect of taxation in the online sports betting market

    OpenAIRE

    Vidal-Puga, Juan

    2016-01-01

    We analyse the effect of taxation in the online sport betting market. This market is characterized by its negligible marginal costs. Taxation can be on volume (General Betting Duty) or on gross profit (Gross Profit Tax). We model the two most popular online sport betting bets: fixed-odds and spread, as compared with another traditional sport betting: parimutuel.

  3. Modulation of allergic immune responses by mucosal application of recombinant lactic acid bacteria producing the major birch pollen allergen Bet v 1.

    Science.gov (United States)

    Daniel, C; Repa, A; Wild, C; Pollak, A; Pot, B; Breiteneder, H; Wiedermann, U; Mercenier, A

    2006-07-01

    Probiotic lactic acid bacteria (LAB) are able to modulate the host immune system and clinical trials have demonstrated that specific strains have the capacity to reduce allergic symptoms. Therefore, we aimed to evaluate the potential of recombinant LAB producing the major birch pollen allergen Bet v 1 for mucosal vaccination against birch pollen allergy. Recombinant Bet v 1-producing Lactobacillus plantarum and Lactococcus lactis strains were constructed. Their immunogenicity was compared with purified Bet v 1 by subcutaneous immunization of mice. Intranasal application of the live recombinant strains was performed to test their immunomodulatory potency in a mouse model of birch pollen allergy. Bet v 1 produced by the LAB was recognized by monoclonal anti-Bet v 1 and IgE antibodies from birch pollen-allergic patients. Systemic immunization with the recombinant strains induced significantly lower IgG1/IgG2a ratios compared with purified Bet v 1. Intranasal pretreatment led to reduced allergen-specific IgE vs enhanced IgG2a levels and reduced interleukin (IL)-5 production of splenocytes in vitro, indicating a shift towards non-allergic T-helper-1 (Th1) responses. Airway inflammation, i.e. eosinophils and IL-5 in lung lavages, was reduced using either Bet v 1-producing or control strains. Allergen-specific secretory IgA responses were enhanced in lungs and intestines after pretreatment with only the Bet v 1-producing strains. Mucosal vaccination with live recombinant LAB, leading to a shift towards non-allergic immune responses along with enhanced allergen-specific mucosal IgA levels offers a promising approach to prevent systemic and local allergic immune responses.

  4. Betting is loving and bettors are predators: a conceptual metaphor approach to online sports betting advertising

    OpenAIRE

    López González, Hibai, 1983-; Guerrero Solé, Frederic; Estévez, Ana; Griffiths, Mark, 1966-

    2017-01-01

    The legalisation of online gambling in multiple territories has caused a growth in the exposure of consumers to online sports betting (OSB) advertising. While some efforts have been made to understand the visible structure of betting promotional messages, little is known about the latent components of OSB advertisements. The present study sought to address this issue by examining the metaphorical conceptualisation of OSB advertising. A sample of Spanish and British television OSB advertisemen...

  5. Does the uptake of wagering inducements predict impulse betting on sport?

    Science.gov (United States)

    Hing, Nerilee; Russell, Alex M T; Li, En; Vitartas, Peter

    2018-03-01

    Background and aims Marketing inducements for addictive products, such as wagering, can prompt impulse purchasing by triggering consumption reminders, urges, and cravings. Wagering inducements incentivize betting by providing bonus bets, money-back guarantees, deposits into betting accounts, and discounts. Their promotion during sporting events, push marketing efforts directed at consumers, and ease of uptake at the point-of-sale, may trigger betting on impulse. This study examined whether the uptake of wagering inducements predicted impulse betting on sport. Methods Australian sports bettors (N = 1,813) completed an online survey measuring their proportion of planned bets, impulse bets before match commencement, and impulse bets during play; frequency of using wagering inducements; and several psychological, behavioral, and demographic variables. Results More frequent users of wagering inducements had a greater tendency to place impulse in-play bets, which were also predicted by problem gambling, higher buying impulsiveness, higher frequency of watching sports, younger age, and higher educational status. Sports bettors with a greater tendency to place impulse bets before match commencement also tended to have higher buying impulsiveness and to be younger, but they used inducements less frequently, and tended to be female, less-educated and non-problem, moderate risk, or problem gamblers. Discussion and conclusions Uptake of wagering inducements appeared to be particularly effective in stimulating impulse in-play betting among problem gamblers and frequent sports viewers. These results suggest that a more cautious approach to the regulation of both in-play bets and wagering inducements may be required to better protect young adults from gambling problems and harm.

  6. Molecularly-Limited Fractal Surface Area of Mineral Powders

    Directory of Open Access Journals (Sweden)

    Petr Jandacka

    2016-05-01

    Full Text Available The topic of the specific surface area (SSA of powders is not sufficiently described in the literature in spite of its nontrivial contribution to adsorption and dissolution processes. Fractal geometry provides a way to determine this parameter via relation SSA ~ x(D − 3s(2 − D, where x (m is the particle size and s (m is a scale. Such a relation respects nano-, micro-, or macro-topography on the surface. Within this theory, the fractal dimension 2 ≤ D < 3 and scale parameter s plays a significant role. The parameter D may be determined from BET or dissolution measurements on several samples, changing the powder particle sizes or sizes of adsorbate molecules. If the fractality of the surface is high, the SSA does not depend on the particle size distribution and vice versa. In this paper, the SSA parameter is analyzed from the point of view of adsorption and dissolution processes. In the case of adsorption, a new equation for the SSA, depending on the term (2 − D∙(s2 − sBET/sBET, is derived, where sBET and s2 are effective cross-sectional diameters for BET and new adsorbates. Determination of the SSA for the dissolution process appears to be very complicated, since the fractality of the surface may change in the process. Nevertheless, the presented equations have good application potential.

  7. Who decides who has won the bet? Total and Anthropogenic Warming Indices

    Science.gov (United States)

    Haustein, K.; Allen, M. R.; Otto, F. E. L.; Schmidt, A.; Frame, D. J.; Forster, P.; Matthews, D.

    2016-12-01

    An extension of the idea of betting markets as a means of revealing opinions about future climate are climate policies indexed to geophysical indicators: for example, to ensure net zero global carbon dioxide emissions by the time anthropogenic warming reaches 1.5 degrees above pre-industrial, given about 1 degree of warming already, emissions must fall, on average, by 20% of their current value for every tenth of a degree of anthropogenic warming from now on. In principle, policies conditioned on some measure of attributable warming are robust to uncertainty in the global climate response: the risk of a higher or lower response than expected is borne by those affected by climate change mitigation policy rather than those affected by climate change impacts, as is the case with emission targets for specific years based on "current understanding" of the response. To implement any indexed policy, or to agree payout terms for any bet on future climate, requires consensus on the definition of the index: how is it calculated, and who is responsible for releasing it? The global mean surface temperature of the current decade relative to pre-industrial may vary by 0.1 degree or more depending on precisely what is measured, what is defined as pre-industrial, and the treatment of regions with sparse data coverage in earlier years. Indices defined using different conventions, however, are all expected to evolve very similarly over the coming decades, so agreeing on a conservative, traceable index such as HadCRUT is more important than debating the "true" global temperature. A more important question is whether indexed policies and betting markets should focus on total warming, including natural and anthropogenic drivers and internal variability, or an Anthropogenic Warming Index (AWI) representing an unbiased estimate of warming attributable to human influence to date. We propose a simple AWI based solely on observed temperatures and global natural and anthropogenic forcing

  8. On Loss Aversion, Level-1 Reasoning, and Betting

    DEFF Research Database (Denmark)

    Erev, Ido; Gilat-Yihyie, Sharon; Marchiori, Davide

    2014-01-01

    Previous research suggests that human reaction to risky opportunities reflects two contradicting biases: “loss aversion”, and “limited level of reasoning” that leads to overconfidence. Rejection of attractive gambles is explained by loss aversion, while counterproductive risk seeking is attributed...... to limited level of reasoning. The current research highlights a shortcoming of this popular (but often implicit) “contradicting biases” assertion. Studies of “negative-sum betting games” reveal high rate of counterproductive betting even when limited level of reasoning and loss aversion imply no betting...

  9. Size and surface AREA analysis of some metallic and intermetallic powders

    International Nuclear Information System (INIS)

    Elmasry, M.A.A.; Elsayed, A.A.; Abadir, M.F.

    1988-01-01

    The powder characterization of three intermetallic compounds ( Cr B, B 4 c and S ib 4 ) and three metallic powders (Fe, Co, and Ni) has been performed. This included the determination of powder density, chemical analysis, impurity analysis, shape factor, particle size analysis and specific surface area. The particle size analysis for the six powders was carried out using three techniques, namely; the 0-23, the microtrac and the fisher sub sieve and size. It was found that the analysis of the two powders and deviates from the log-normal probability distribution and the deviation was corrected. The specific surface area of the powders was measured using the high speed surface area analysis (BET method), and it was also calculated from surface area analysis findings, the BET technique was found to give the highest specific surface area values, and was attributed to the inclusion of internal porosity in the measurement. 8 fig., 10 tab

  10. Understanding persuasive attributes of sports betting advertisements: A conjoint analysis of selected elements.

    Science.gov (United States)

    Hing, Nerilee; Vitartas, Peter; Lamont, Matthew

    2017-12-01

    Background and aims Despite recent growth in sports betting advertising, minimal research has examined the influence of different advertising message attributes on betting attitudes and behaviors. This study aimed to identify which attributes of sports betting advertisements most engage attention, interest, desire and likelihood of betting among non-problem, low-risk, moderate-risk, and problem gamblers. Methods A novel approach utilizing an experimental design incorporating conjoint analysis examined the effects of: three message formats (commentary, on-screen display, and studio crossover); four appeals (neutral, jovial, ease of placing the bet, and sense of urgency); three types of presenters (match presenter, sports betting operator, and attractive non-expert female presenter); and four bet types (traditional, exotic key event, risk-free, and micro-bet). A professional film company using paid actors produced 20 mock television advertisements simulating typical gambling messages based on the conjoint approach. These were embedded into an online survey of 611 Australian adults. Results The most attention-grabbing attributes were type of presenter and type of bet. The attractive non-expert female presenter gained more attention from all gambler groups than other presenters. The type of bet was most persuasive in converting attention into likely betting among all gambler groups, with the risk-free bet being much more persuasive than other bet types. Problem gamblers were distinct by their greater attraction to in-play micro-bets. Discussion and conclusion Given the potential for incentivized bets offering financial inducements and for in-play micro-bets to undermine harm minimization and consumer protection, regulators and wagering operators should reconsider whether these bet types are consistent with their responsible gambling objectives.

  11. Genetic variants alter T-bet binding and gene expression in mucosal inflammatory disease.

    Directory of Open Access Journals (Sweden)

    Katrina Soderquest

    2017-02-01

    Full Text Available The polarization of CD4+ T cells into distinct T helper cell lineages is essential for protective immunity against infection, but aberrant T cell polarization can cause autoimmunity. The transcription factor T-bet (TBX21 specifies the Th1 lineage and represses alternative T cell fates. Genome-wide association studies have identified single nucleotide polymorphisms (SNPs that may be causative for autoimmune diseases. The majority of these polymorphisms are located within non-coding distal regulatory elements. It is considered that these genetic variants contribute to disease by altering the binding of regulatory proteins and thus gene expression, but whether these variants alter the binding of lineage-specifying transcription factors has not been determined. Here, we show that SNPs associated with the mucosal inflammatory diseases Crohn's disease, ulcerative colitis (UC and celiac disease, but not rheumatoid arthritis or psoriasis, are enriched at T-bet binding sites. Furthermore, we identify disease-associated variants that alter T-bet binding in vitro and in vivo. ChIP-seq for T-bet in individuals heterozygous for the celiac disease-associated SNPs rs1465321 and rs2058622 and the IBD-associated SNPs rs1551398 and rs1551399, reveals decreased binding to the minor disease-associated alleles. Furthermore, we show that rs1465321 is an expression quantitative trait locus (eQTL for the neighboring gene IL18RAP, with decreased T-bet binding associated with decreased expression of this gene. These results suggest that genetic polymorphisms may predispose individuals to mucosal autoimmune disease through alterations in T-bet binding. Other disease-associated variants may similarly act by modulating the binding of lineage-specifying transcription factors in a tissue-selective and disease-specific manner.

  12. SURFACE PROPERTIES AND CATALYTIC PERFORMANCE OF Pt ...

    African Journals Online (AJOL)

    various temperatures of precipitates obtained from aqueous solutions in the ... The oxidation reactivity of VOCs is in the following order: alcohols > aldheydes > aromatics ... Specific surface areas (SSA) were calculated by the BET method from ...

  13. 18 CFR 706.209 - Gambling, betting, and lotteries.

    Science.gov (United States)

    2010-04-01

    ... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Gambling, betting, and... EMPLOYEE RESPONSIBILITIES AND CONDUCT Conduct and Responsibilities of Employees § 706.209 Gambling, betting... while on duty for the Government, in any gambling activity, including the operation of a gambling device...

  14. BET Bromodomain Inhibition Releases the Mediator Complex from Select cis-Regulatory Elements.

    Science.gov (United States)

    Bhagwat, Anand S; Roe, Jae-Seok; Mok, Beverly Y L; Hohmann, Anja F; Shi, Junwei; Vakoc, Christopher R

    2016-04-19

    The bromodomain and extraterminal (BET) protein BRD4 can physically interact with the Mediator complex, but the relevance of this association to the therapeutic effects of BET inhibitors in cancer is unclear. Here, we show that BET inhibition causes a rapid release of Mediator from a subset of cis-regulatory elements in the genome of acute myeloid leukemia (AML) cells. These sites of Mediator eviction were highly correlated with transcriptional suppression of neighboring genes, which are enriched for targets of the transcription factor MYB and for functions related to leukemogenesis. A shRNA screen of Mediator in AML cells identified the MED12, MED13, MED23, and MED24 subunits as performing a similar regulatory function to BRD4 in this context, including a shared role in sustaining a block in myeloid maturation. These findings suggest that the interaction between BRD4 and Mediator has functional importance for gene-specific transcriptional activation and for AML maintenance. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

  15. BET bromodomain inhibition of MYC-amplified medulloblastoma.

    Science.gov (United States)

    Bandopadhayay, Pratiti; Bergthold, Guillaume; Nguyen, Brian; Schubert, Simone; Gholamin, Sharareh; Tang, Yujie; Bolin, Sara; Schumacher, Steven E; Zeid, Rhamy; Masoud, Sabran; Yu, Furong; Vue, Nujsaubnusi; Gibson, William J; Paolella, Brenton R; Mitra, Siddhartha S; Cheshier, Samuel H; Qi, Jun; Liu, Kun-Wei; Wechsler-Reya, Robert; Weiss, William A; Swartling, Fredrik J; Kieran, Mark W; Bradner, James E; Beroukhim, Rameen; Cho, Yoon-Jae

    2014-02-15

    MYC-amplified medulloblastomas are highly lethal tumors. Bromodomain and extraterminal (BET) bromodomain inhibition has recently been shown to suppress MYC-associated transcriptional activity in other cancers. The compound JQ1 inhibits BET bromodomain-containing proteins, including BRD4. Here, we investigate BET bromodomain targeting for the treatment of MYC-amplified medulloblastoma. We evaluated the effects of genetic and pharmacologic inhibition of BET bromodomains on proliferation, cell cycle, and apoptosis in established and newly generated patient- and genetically engineered mouse model (GEMM)-derived medulloblastoma cell lines and xenografts that harbored amplifications of MYC or MYCN. We also assessed the effect of JQ1 on MYC expression and global MYC-associated transcriptional activity. We assessed the in vivo efficacy of JQ1 in orthotopic xenografts established in immunocompromised mice. Treatment of MYC-amplified medulloblastoma cells with JQ1 decreased cell viability associated with arrest at G1 and apoptosis. We observed downregulation of MYC expression and confirmed the inhibition of MYC-associated transcriptional targets. The exogenous expression of MYC from a retroviral promoter reduced the effect of JQ1 on cell viability, suggesting that attenuated levels of MYC contribute to the functional effects of JQ1. JQ1 significantly prolonged the survival of orthotopic xenograft models of MYC-amplified medulloblastoma (P < 0.001). Xenografts harvested from mice after five doses of JQ1 had reduced the expression of MYC mRNA and a reduced proliferative index. JQ1 suppresses MYC expression and MYC-associated transcriptional activity in medulloblastomas, resulting in an overall decrease in medulloblastoma cell viability. These preclinical findings highlight the promise of BET bromodomain inhibitors as novel agents for MYC-amplified medulloblastoma. ©2013 AACR

  16. Market Efficiency and Behavioral Biases in the WNBA Betting Market

    Directory of Open Access Journals (Sweden)

    Rodney J. Paul

    2014-04-01

    Full Text Available The betting market for the Women’s National Basketball Association (WNBA is a thin financial market, which does not attract much interest from sports bettors. Given these characteristics, it is possible that profitable wagering strategies could exist for informed bettors of the WNBA. Using betting data on the WNBA from 2007–2012, we find that simple betting strategies do not earn statistically significant returns. WNBA bettors are like NBA bettors; however, in that they strongly prefer the best teams, particularly when they are on the road. Despite this clear bias, betting against the most popular public wagers is not found to earn statistically significant profits.

  17. Role of bundle helices in a regulatory crosstalk in the trimeric betaine transporter BetP.

    Science.gov (United States)

    Gärtner, Rebecca M; Perez, Camilo; Koshy, Caroline; Ziegler, Christine

    2011-12-02

    The Na(+)-coupled betaine symporter BetP regulates transport activity in response to hyperosmotic stress only in its trimeric state, suggesting a regulatory crosstalk between individual protomers. BetP shares the overall fold of two inverted structurally related five-transmembrane (TM) helix repeats with the sequence-unrelated Na(+)-coupled symporters LeuT, vSGLT, and Mhp1, which are neither trimeric nor regulated in transport activity. Conformational changes characteristic for this transporter fold involve the two first helices of each repeat, which form a four-TM-helix bundle. Here, we identify two ionic networks in BetP located on both sides of the membrane that might be responsible for BetP's unique regulatory behavior by restricting the conformational flexibility of the four-TM-helix bundle. The cytoplasmic ionic interaction network links both first helices of each repeat in one protomer to the osmosensing C-terminal domain of the adjacent protomer. Moreover, the periplasmic ionic interaction network conformationally locks the four-TM-helix bundle between the same neighbor protomers. By a combination of site-directed mutagenesis, cross-linking, and betaine uptake measurements, we demonstrate how conformational changes in individual bundle helices are transduced to the entire bundle by specific inter-helical interactions. We suggest that one purpose of bundle networking is to assist crosstalk between protomers during transport regulation by specifically modulating the transition from outward-facing to inward-facing state. Copyright © 2011 Elsevier Ltd. All rights reserved.

  18. Effects of expertise on football betting.

    Science.gov (United States)

    Khazaal, Yasser; Chatton, Anne; Billieux, Joël; Bizzini, Lucio; Monney, Grégoire; Fresard, Emmanuelle; Thorens, Gabriel; Bondolfi, Guido; El-Guebaly, Nady; Zullino, Daniele; Khan, Riaz

    2012-05-11

    Football (soccer) is one of the most popular sports in the world, including Europe. It is associated with important betting activities. A common belief, widely spread among those who participate in gambling activities, is that knowledge and expertise on football lead to better prediction skills for match outcomes. If unfounded, however, this belief should be considered as a form of "illusion of control." The aim of this study was to examine whether football experts are better than nonexperts at predicting football match scores. Two hundred and fifty-eight persons took part in the study: 21.3% as football experts, 54.3% as laypersons (non-initiated to football), and 24.4% as football amateurs. They predicted the scores of the first 10 matches of the 2008 UEFA European Football Championship. Logistic regressions were carried out to assess the link between the accuracy of the forecasted scores and the expertise of the participants (expert, amateur, layperson), controlling for age and gender. The variables assessed did not predict the accuracy of scoring prognosis (R2 ranged from 1% to 6%). Expertise, age, and gender did not appear to have an impact on the accuracy of the football match prognoses. Therefore, the belief that football expertise improves betting skills is no more than a cognitive distortion called the "illusion of control." Gamblers may benefit from psychological interventions that target the illusion of control related to their believed links between betting skills and football expertise. Public health policies may need to consider the phenomenon in order to prevent problem gambling related to football betting.

  19. Improved Insulin Sensitivity despite Increased Visceral Adiposity in Mice Deficient for the Immune Cell Transcription Factor T-bet

    Science.gov (United States)

    Stolarczyk, Emilie; Vong, Chi Teng; Perucha, Esperanza; Jackson, Ian; Cawthorne, Michael A.; Wargent, Edward T.; Powell, Nick; Canavan, James B.; Lord, Graham M.; Howard, Jane K.

    2013-01-01

    Summary Low-grade inflammation in fat is associated with insulin resistance, although the mechanisms are unclear. We report that mice deficient in the immune cell transcription factor T-bet have lower energy expenditure and increased visceral fat compared with wild-type mice, yet paradoxically are more insulin sensitive. This striking phenotype, present in young T-bet−/− mice, persisted with high-fat diet and increasing host age and was associated with altered immune cell numbers and cytokine secretion specifically in visceral adipose tissue. However, the favorable metabolic phenotype observed in T-bet-deficient hosts was lost in T-bet−/− mice also lacking adaptive immunity (T-bet−/−xRag2−/−), demonstrating that T-bet expression in the adaptive rather than the innate immune system impacts host glucose homeostasis. Indeed, adoptive transfer of T-bet-deficient, but not wild-type, CD4+ T cells to Rag2−/− mice improved insulin sensitivity. Our results reveal a role for T-bet in metabolic physiology and obesity-associated insulin resistance. PMID:23562076

  20. Sports betting marketing during sporting events: a stadium and broadcast census of Australian Football League matches.

    Science.gov (United States)

    Thomas, Samantha; Lewis, Sophie; Duong, Jenny; McLeod, Colin

    2012-04-01

    Using Australian Football League (AFL) matches as a case study, we investigated the frequency, length and content of marketing strategies for sports betting during two specific settings: 1) at stadiums during four live matches; and 2) during eight televised broadcasts of matches. Census of sports betting marketing during Round 12 of the 2011 AFL premiership season. Per match, there was an average of 58.5 episodes (median 49.5, s.d 27.8) and 341.1 minutes (median 324.1 minutes and s.d 44.5) of sports betting marketing at stadiums, and 50.5 episodes (median 53.5, s.d 45.2) and 4.8 minutes (median 5.0 minutes, s.d 4.0) during televised broadcasts. A diverse range of marketing techniques were used to: a) embed sports betting within the game; b) align sports betting with fans' overall experience of the game; and c) encourage individuals to bet live during the game. There were very few visible or audible messages (such as responsible gambling or Gambler's Help messages) to counter-frame the overwhelmingly positive messages that individuals received about sports betting during the match. This study raises important questions about the impacts of saturation, integrated and impulse gambling marketing strategies in sporting matches. Future research should explore: 1) how wagering industry marketing strategies may affect the attitudes and behaviours of community sub-groups (e.g. young male sports fans, and children); and 2) which public health and policy strategies, including regulation and harm minimisation messaging, will be effective in responding to wagering industry marketing strategies during sporting matches. © 2012 The Authors. ANZJPH © 2012 Public Health Association of Australia.

  1. Bet-hedging applications for conservation

    Indian Academy of Sciences (India)

    Unknown

    Bet hedging; Bitterroot wilderness; environmental correlation; grizzly bear; least tern; Sterna antillarum; Ursus arctos horribilis ... market, a hedging investor can reduce the risk of devas- ..... populations were approximated by three methods:.

  2. Clinical trials for BET inhibitors run ahead of the science.

    Science.gov (United States)

    Andrieu, Guillaume; Belkina, Anna C; Denis, Gerald V

    2016-03-01

    Several cancer clinical trials for small molecule inhibitors of BET bromodomain proteins have been initiated. There is enthusiasm for the anti-proliferative effect of inhibiting BRD4, one of the targets of these inhibitors, which is thought to cooperate with MYC, a long-desired target for cancer therapeutics. However, no current inhibitor is selective for BRD4 among the three somatic BET proteins, which include BRD2 and BRD3; their respective functions are partially overlapping and none are functionally redundant with BRD4. Each BET protein controls distinct transcriptional pathways that are important for functions beyond cancer cell proliferation, including insulin production, cytokine gene transcription, T cell differentiation, adipogenesis and most seriously, active repression of dangerous latent viruses like HIV. BET inhibitors have been shown to reactivate HIV in human cells. Failure to appreciate that at concentrations used, no available BET inhibitor is member-selective, or to develop a sound biological basis to understand the diverse functions of BET proteins before undertaking for these clinical trials is reckless and likely to lead to adverse events. More mechanistic information from new basic science studies should enable proper focus on the most relevant cancers and define the expected side effect profiles. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Adults Learning Mathematics: What We Should Know about Betting and Bookkeeping?

    Science.gov (United States)

    Maasz, Juergen; Siller, Hans-Stefan

    2010-01-01

    A lot of people risk money with bets on sport events or other events. Bookkeepers that offer such bets earn a lot of money. We are making a proposal (more exactly: a concept for a part of a basic mathematics course) for learning mathematics behind the screen (internet bets are very popular). Learners should organize a "sports event"…

  4. Effects of expertise on football betting

    Directory of Open Access Journals (Sweden)

    Khazaal Yasser

    2012-05-01

    Full Text Available Abstract Background Football (soccer is one of the most popular sports in the world, including Europe. It is associated with important betting activities. A common belief, widely spread among those who participate in gambling activities, is that knowledge and expertise on football lead to better prediction skills for match outcomes. If unfounded, however, this belief should be considered as a form of “illusion of control.” The aim of this study was to examine whether football experts are better than nonexperts at predicting football match scores. Methods Two hundred and fifty-eight persons took part in the study: 21.3% as football experts, 54.3% as laypersons (non-initiated to football, and 24.4% as football amateurs. They predicted the scores of the first 10 matches of the 2008 UEFA European Football Championship. Logistic regressions were carried out to assess the link between the accuracy of the forecasted scores and the expertise of the participants (expert, amateur, layperson, controlling for age and gender. Results The variables assessed did not predict the accuracy of scoring prognosis (R2 ranged from 1% to 6%. Conclusions Expertise, age, and gender did not appear to have an impact on the accuracy of the football match prognoses. Therefore, the belief that football expertise improves betting skills is no more than a cognitive distortion called the “illusion of control.” Gamblers may benefit from psychological interventions that target the illusion of control related to their believed links between betting skills and football expertise. Public health policies may need to consider the phenomenon in order to prevent problem gambling related to football betting.

  5. Determination of oxide film thickness on aluminium using 14-MeV neutron activation and BET method

    International Nuclear Information System (INIS)

    Foerster, H.

    1983-01-01

    A new method is described for the determination of the mean film thickness of aluminium oxides by 14-MeV neutron activation analysis of the oxygen and by BET measurement of the surface area. The mean film thickness obtained is independent of the surface roughness. Stable oxide films consisting of only a few atomic layers of oxygen are detected on aluminium. (author)

  6. Synthesis and characterization of high-surface-area millimeter-sized silica beads with hierarchical multi-modal pore structure by the addition of agar

    Energy Technology Data Exchange (ETDEWEB)

    Han, Yosep; Choi, Junhyun [Department of Mineral Resources and Energy Engineering, Chonbuk National University, 567 Baekje-daero, Deokjin-gu, Jeonju-si, Jeollabuk-do 561–756 (Korea, Republic of); Tong, Meiping, E-mail: tongmeiping@iee.pku.edu.cn [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, College of Environmental Sciences and Engineering, Peking University, Beijing 100871 (China); Kim, Hyunjung, E-mail: kshjkim@jbnu.ac.kr [Department of Mineral Resources and Energy Engineering, Chonbuk National University, 567 Baekje-daero, Deokjin-gu, Jeonju-si, Jeollabuk-do 561–756 (Korea, Republic of)

    2014-04-01

    Millimeter-sized spherical silica foams (SSFs) with hierarchical multi-modal pore structure featuring high specific surface area and ordered mesoporous frameworks were successfully prepared using aqueous agar addition, foaming and drop-in-oil processes. The pore-related properties of the prepared spherical silica (SSs) and SSFs were systematically characterized by field emission-scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), small-angle X-ray diffraction (SAXRD), Hg intrusion porosimetry, and N{sub 2} adsorption–desorption isotherm measurements. Improvements in the BET surface area and total pore volume were observed at 504 m{sup 2} g{sup −1} and 5.45 cm{sup 3} g{sup −1}, respectively, after an agar addition and foaming process. Despite the increase in the BET surface area, the mesopore wall thickness and the pore size of the mesopores generated from the block copolymer with agar addition were unchanged based on the SAXRD, TEM, and BJH methods. The SSFs prepared in the present study were confirmed to have improved BET surface area and micropore volume through the agar loading, and to exhibit interconnected 3-dimensional network macropore structure leading to the enhancement of total porosity and BET surface area via the foaming process. - Highlights: • Millimeter-sized spherical silica foams (SSFs) are successfully prepared. • SSFs exhibit high BET surface area and ordered hierarchical pore structure. • Agar addition improves BET surface area and micropore volume of SSFs. • Foaming process generates interconnected 3-D network macropore structure of SSFs.

  7. Metallic conductivity in a disordered charge-transfer salt derived from cis-BET-TTF

    Energy Technology Data Exchange (ETDEWEB)

    Rovira, C. [Inst. de Ciencia de Materials de Barcelona (CSIC) (Spain); Tarres, J. [Inst. de Ciencia de Materials de Barcelona (CSIC) (Spain); Ribera, E. [Inst. de Ciencia de Materials de Barcelona (CSIC) (Spain); Veciana, J. [Inst. de Ciencia de Materials de Barcelona (CSIC) (Spain); Canadell, E. [Inst. de Ciencia de Materials de Barcelona (CSIC) (Spain); Molins, E. [Inst. de Ciencia de Materials de Barcelona (CSIC) (Spain); Mas, M. [Inst. de Ciencia de Materials de Barcelona (CSIC) (Spain); Laukhin, V. [Inst. de Ciencia de Materials de Barcelona (CSIC) (Spain)]|[Rossijskaya Akademiya Nauk, Chernogolovka (Russian Federation). Inst. Khimicheskoj Fiziki; Doublet, M.L. [Lab. de Structure et Dynamique (CNRS), Univ. de Montpellier 2 (France); Cowan, D.O. [Johns Hopkins Univ., Baltimore, MD (United States). Dept. of Chemistry; Yang, S. [Johns Hopkins Univ., Baltimore, MD (United States). Dept. of Chemistry

    1997-02-28

    The first example of a metallic charge-transfer salt derived from cis-bis(ethylenethio)-tetrathiafulvalene (BET-TTF) is reported. (BET-TTF){sub 2}SCN and (BET-TTF)SCN salts were obtained by electrocrystallization starting from trans-BET-TTF. X-ray crystal structure of the mixed-valence salt revealed that trans-cis isomerization occurs upon one electron oxidation. In spite of the structural disorder in both BET-TTF and the counterion, 2:1 salt is metallic down to 60 K and then resistance increases slowly down to 4 K. (orig.)

  8. Archaeology of Bet Dwarka Island

    Digital Repository Service at National Institute of Oceanography (India)

    Sundaresh; Gaur, A.S.

    Explorations along the shore and in the intertidal zone at Bet Dwarka island, Gujarat, India were carried out by the Marine Archaeology Centre of National Institute of Oceanography (NIO), Goa, India between 1981-1994. Artefacts of both...

  9. Uso da Fibra de Coco em Betão

    OpenAIRE

    Gonçalves, Stephanie Assunção

    2016-01-01

    O presente trabalho tem como objetivo avaliar as resistências à compressão axial, tração por compressão diametral e tração na flexão, módulos de elasticidade estático e dinâmico do betão reforçado com fibra de coco (BRFC), tendo como referência o betão preparado sem a adição de fibra. A escolha da fibra natural decorreu da necessidade de utilizar os resíduos gerados pelo consumo do coco verde. Sendo assim, este trabalho apresenta uma breve história do betão, suas propriedades, tipos de fibras...

  10. Measuring the specific surface area of natural and manmade glasses: effects of formation process, morphology, and particle size

    International Nuclear Information System (INIS)

    Papelis, Charalambos; Um, Wooyong; Russel, Charles E.; Chapman, Jenny B.

    2003-01-01

    The specific surface area of natural and manmade solid materials is a key parameter controlling important interfacial processes in natural environments and engineered systems, including dissolution reactions and sorption processes at solid-fluid interfaces. To improve our ability to quantify the release of trace elements trapped in natural glasses, the release of hazardous compounds trapped in manmade glasses, or the release of radionuclides from nuclear melt glass, we measured the specific surface area of natural and manmade glasses as a function of particle size, morphology, and composition. Volcanic ash, volcanic tuff, tektites, obsidian glass, and in situ vitrified rock were analyzed. Specific surface area estimates were obtained using krypton as gas adsorbent and the BET model. The range of surface areas measured exceeded three orders of magnitude. A tektite sample had the highest surface area (1.65 m2/g), while one of the samples of in situ vitrified rock had the lowest surf ace area (0.0016 m2/g). The specific surface area of the samples was a function of particle size, decreasing with increasing particle size. Different types of materials, however, showed variable dependence on particle size, and could be assigned to one of three distinct groups: (1) samples with low surface area dependence on particle size and surface areas approximately two orders of magnitude higher than the surface area of smooth spheres of equivalent size. The specific surface area of these materials was attributed mostly to internal porosity and surface roughness. (2) samples that showed a trend of decreasing surface area dependence on particle size as the particle size increased. The minimum specific surface area of these materials was between 0.1 and 0.01 m2/g and was also attributed to internal porosity and surface roughness. (3) samples whose surface area showed a monotonic decrease with increasing particle size, never reaching an ultimate surface area limit within the particle

  11. Sports betting: can gamblers beat randomness?

    Science.gov (United States)

    Cantinotti, Michael; Ladouceur, Robert; Jacques, Christian

    2004-06-01

    Although skills are not considered relevant in chance-governed activities, only a few studies have assessed the extent to which sport expert skills in wagering are a manifestation of the illusion of control. This study examined (a) whether expert hockey bettors could make better predictions than chance, (b) whether expert hockey bettors could achieve greater monetary gains than chance, and (c) what kind of strategies hockey gamblers rely on when betting. Accordingly, 30 participants were asked to report their state lottery hockey bets on 6 occasions. We suggest that the information used by bettors, along with near-misses, reinforces their perception of expertise. The results of this experiment suggest that the so-called "skills" of the sports bettors are cognitive distortions. (c) 2004 APA, all rights reserved

  12. Learning Mathematics or Losing Money--Betting as a Topic for Mathematical Education

    Science.gov (United States)

    Siller, Hans-Stefan; MaaB, Jurgen

    2012-01-01

    No risk, no fun--betting on sports events costs the gamblers a lot of money and brings excellent profits to those who offer the bets. Among the people who bet on a regular basis, the proportion of young adults is frighteningly high. We now suggest a concept (as part of a basic mathematics course) for acquiring the necessary mathematical knowledge…

  13. Popcorn-Derived Porous Carbon Flakes with an Ultrahigh Specific Surface Area for Superior Performance Supercapacitors.

    Science.gov (United States)

    Hou, Jianhua; Jiang, Kun; Wei, Rui; Tahir, Muhammad; Wu, Xiaoge; Shen, Ming; Wang, Xiaozhi; Cao, Chuanbao

    2017-09-13

    Popcorn-derived porous carbon flakes have been successfully fabricated from the biomass of maize. Utilizing the "puffing effect", the nubby maize grain turned into materials with an interconnected honeycomb-like porous structure composed of carbon flakes. The following chemical activation method enabled the as-prepared products to possess optimized porous structures for electrochemical energy-storage devices, such as multilayer flake-like structures, ultrahigh specific surface area (S BET : 3301 m 2 g -1 ), and a high content of micropores (microporous surface area of 95%, especially the optimized sub-nanopores with the size of 0.69 nm) that can increase the specific capacitance. The as-obtained sample displayed excellent specific capacitance of 286 F g -1 at 90 A g -1 for supercapacitors. Moreover, the unique porous structure demonstrated an ideal way to improve the volumetric energy density performance. A high energy density of 103 Wh kg -1 or 53 Wh L -1 has been obtained in the case of ionic liquid electrolyte, which is the highest among reported biomass-derived carbon materials and will satisfy the urgent requirements of a primary power source for electric vehicles. This work may prove to be a fast, green, and large-scale synthesis route by using the large nubby granular materials to synthesize applicable porous carbons in energy-storage devices.

  14. Regression Tests and the Efficiency of Fixed Odds Betting Markets

    NARCIS (Netherlands)

    Koning, Ruud H.

    The informational content of odds posted in sports betting market has been an ongoing topic of research. In this paper, I test whether fixed odds betting markets in soccer are informationally efficient. The contributions of the paper are threefold: first, I propose a simple yet flexible statistical

  15. The Factors that Effect to Take Part in Betting

    Directory of Open Access Journals (Sweden)

    Alp Çelik

    2016-10-01

    Full Text Available Because of its’ nature, betting in sports includes factors such as huge revenue, hot money flow, entertainment, thrill, dreams and happening of these dreams. Herewith, these factors pointed out in society effects people’s betting motivation. The purpose of this study was to investigate the factors that effects participators/players to take part in betting. While the universe of the study composed players in Ankara, the sampling group consisted of a legal bookmaker of Spor Toto Teşkilat Bakanlığı and Türkiye Jokey Kulübü that is easily accessible and has a huge rate of revenue. In total, 80 participators (15 students, 20 workers, 20 civil servants, 15 handicraftsmen and 10 self employments participated to study and filled in the questionnaire that expert opinion was taken, validity and reliability were done, According to the results acquired, it was determined that participators take part in betting to enhance the quality of life, bring enjoy and attraction of their life, getting rid of stress and most importantly making money because of some reasons such as economic crisis and financial difficulty in their society, their low income level and their debts.

  16. Betões de elevado desempenho de custo reduzido utilizando materiais correntes

    OpenAIRE

    Camões, Aires; Aguiar, J. L. Barroso de; Rocha, Patrício; Jalali, Said; Pereira, J. C.

    1999-01-01

    Para a produção de betões de elevado desempenho (BED) é genericamente aceite que são necessários materiais criteriosamente seleccionados, obrigando assim a um acréscimo significativo do custo inicial dos BED quando confrontados com betões correntes. Este trabalho pretende abordar duas características: possibilidade de produzir betões de elevado desempenho que incorporam materiais considerados correntes, nomeadamente cinzas volantes com teor de inqueimados superior ao máximo regulamentar e ine...

  17. BET inhibitors in metastatic prostate cancer: therapeutic implications and rational drug combinations.

    Science.gov (United States)

    Markowski, Mark C; De Marzo, Angelo M; Antonarakis, Emmanuel S

    2017-12-01

    The bromodomain and extra-terminal (BET) family of proteins are epigenetic readers of acetylated histones regulating a vast network of protein expression across many different cancers. Therapeutic targeting of BET is an attractive area of clinical development for metastatic castration-resistant prostate cancer (mCRPC), particularly due to its putative effect on c-MYC expression and its interaction with the androgen receptor (AR). Areas covered: We speculate that a combination approach using inhibitors of BET proteins (BETi) with other targeted therapies may be required to improve the therapeutic index of BET inhibition in the management of prostate cancer. Preclinical data has identified several molecular targets that may enhance the effect of BET inhibition in the clinic. This review will summarize the known preclinical data implicating BET as an important therapeutic target in advanced prostate cancer, highlight the ongoing clinical trials targeting this protein family, and speculate on rationale combination strategies using BETi together with other agents in prostate cancer. A literature search using Pubmed was performed for this review. Expert opinion: Use of BETi in the treatment of mCRPC patients may require the addition of a second novel agent.

  18. Betting Against Correlation

    DEFF Research Database (Denmark)

    Asness, Clifford S.; Frazzini, Andrea; Gormsen, Niels Joachim

    We test whether the low-risk effect is driven by (a) leverage constraints and thus risk should be measured using beta vs. (b) behavioral effects and thus risk should be measured by idiosyncratic risk. Beta depends on volatility and correlation, where only volatility is related to idiosyncratic risk....... Hence, the new factor betting against correlation (BAC) is particularly suited to differentiating between leverage constraints vs. lottery explanations. BAC produces strong performance in the US and internationally, supporting leverage constraint theories. Similarly, we construct the new factor SMAX...

  19. Asthma: T-bet--a master controller?

    Science.gov (United States)

    Robinson, Douglas S; Lloyd, Clare M

    2002-04-30

    The transcription factors T-bet and GATA3 are important reciprocal determinants of Th1 and Th2 T helper cell differentiation. Recent evidence suggests that these factors may affect airway immunopathology in asthma.

  20. Frictional behavior and BET surface-area changes of SAFOD gouge at intermediate to seismic slip rates

    Science.gov (United States)

    Sawai, Michiyo; Shimamoto, Toshihiko; Mitchell, Thomas; Kitajima, Hiroko; Hirose, Takehiro

    2013-04-01

    The San Andreas Fault Observatory at Depth (SAFOD) Drilling site is located near the southern end of the creeping section of the San Andreas fault. Experimental studies on the frictional properties of fault gouge from SAFOD drill cores may provide valuable information on the cause of diverse fault motion. We conducted friction experiments on gouge from the southwest deformation zone (SDZ, Phase III core; Hole G-Run 2-Section 8) where creep is confirmed by ongoing borehole casing deformation, at intermediate to high slip rates (10-5 to 1.3 m/s), at a normal stress of about 1 MPa, and under both dry (room humidity) and wet (25 wt% of H2O added, drained tests) conditions. Experiments were performed with two rotary-shear friction apparatuses. One gram of gouge was placed between specimens of Belfast gabbro 25 mm in diameter surrounded by a Teflon sleeve to confine the gouge. Slip rate was first decreased and then increased in a step-wise manner to obtain the steady-state friction at intermediate slip rates. The friction coefficient increases from about 0.13 to 0.37 as the slip rate increases from 0.8 x 10-5 to 9.7 x 10-3 m/s. Our results agree with frictional strength measured at higher effective normal stress (100 MPa) by the Brown University group in the same material. Data shows pronounced velocity strengthening at intermediate slip rates, which is unfavorable for rupture nucleation and may be a reason for having creep behavior. On the other hand, the steady-state friction markedly decreases at high velocity, and such weakening may allow earthquake rupture to propagate into the creeping section, once the intermediate strength barrier is overcome. Gouge temperature, measured at the edge of the stationary sample during seismic fault motion, increased to around 175oC under dry conditions, but increased up to 100oC under wet conditions. We measured BET surface area of gouge before and after deformation to determine the energy used for grain crushing. The initial

  1. A STRATEGIC ASSESSMENT OF THE ONLINE SPORTS BETTING INDUSTRY IN THE UNITED KINGDOM

    OpenAIRE

    Skogman, Ville

    2015-01-01

    A strategic assessment of the sports betting industry in the United Kingdom. The dissertation focuses on the field of strategic management, through which it tries to identify the competitive advantage of three operators in the United Kingdom online sports betting market; Betfair Group plc, Bet365 and William Hill plc.

  2. Bet-hedging applications for conservation

    Indian Academy of Sciences (India)

    One of the early tenets of conservation biology is that population viability is enhanced by maintaining multiple populations of a species. The strength of this tenet is justified by principles of bet-hedging. Management strategies that reduce variance in population size will also reduce risk of extinction. Asynchrony in population ...

  3. Delayed bet-hedging resilience strategies under environmental fluctuations

    Science.gov (United States)

    Ogura, Masaki; Wakaiki, Masashi; Rubin, Harvey; Preciado, Victor M.

    2017-05-01

    Many biological populations, such as bacterial colonies, have developed through evolution a protection mechanism, called bet hedging, to increase their probability of survival under stressful environmental fluctuation. In this context, the concept of preadaptation refers to a common type of bet-hedging protection strategy in which a relatively small number of individuals in a population stochastically switch their phenotypes to a dormant metabolic state in which they increase their probability of survival against potential environmental shocks. Hence, if an environmental shock took place at some point in time, preadapted organisms would be better adapted to survive and proliferate once the shock is over. In many biological populations, the mechanisms of preadaptation and proliferation present delays whose influence in the fitness of the population are not well understood. In this paper, we propose a rigorous mathematical framework to analyze the role of delays in both preadaptation and proliferation mechanisms in the survival of biological populations, with an emphasis on bacterial colonies. Our theoretical framework allows us to analytically quantify the average growth rate of a bet-hedging bacterial colony with stochastically delayed reactions with arbitrary precision. We verify the accuracy of the proposed method by numerical simulations and conclude that the growth rate of a bet-hedging population shows a nontrivial dependency on their preadaptation and proliferation delays. Contrary to the current belief, our results show that faster reactions do not, in general, increase the overall fitness of a biological population.

  4. Sorption of uranium (VI) on homoionic sodium smectite experimental study and surface complexation modeling.

    Science.gov (United States)

    Korichi, Smain; Bensmaili, Aicha

    2009-09-30

    )-BET specific surface area, SSA(BET) (thus, total edge site concentrations). The specific surface area should be at least 80-100m(2)/g for smectite clays in order to reach convergence during the modeling. The range of 10-20% SSA(BET) was used to estimate the values of edge site surfaces that led to the convergence during modeling. An agreement between the experimental data and model predictions is found reasonable when 15% SSA(BET) was used as edge site surface. However, the predicted U (VI) adsorption underestimated and overestimated the experimental observations at the 10 and 20% of the measured SSA(BET), respectively. The dependence of uranium sorption modeling results on specific surface area and edge site surface is useful to describe and predict U (VI) retardation as a function of chemical conditions in the field-scale reactive transport simulations. Therefore this approach can be used in the environmental quality assessment.

  5. Characterization of the porosity of human dental enamel and shear bond strength in vitro after variable etch times: initial findings using the BET method.

    Science.gov (United States)

    Nguyen, Trang T; Miller, Arthur; Orellana, Maria F

    2011-07-01

    (1) To quantitatively characterize human enamel porosity and surface area in vitro before and after etching for variable etching times; and (2) to evaluate shear bond strength after variable etching times. Specifically, our goal was to identify the presence of any correlation between enamel porosity and shear bond strength. Pore surface area, pore volume, and pore size of enamel from extracted human teeth were analyzed by Brunauer-Emmett-Teller (BET) gas adsorption before and after etching for 15, 30, and 60 seconds with 37% phosphoric acid. Orthodontic brackets were bonded with Transbond to the samples with variable etch times and were subsequently applied to a single-plane lap shear testing system. Pore volume and surface area increased after etching for 15 and 30 seconds. At 60 seconds, this increase was less pronounced. On the contrary, pore size appears to decrease after etching. No correlation was found between variable etching times and shear strength. Samples etched for 15, 30, and 60 seconds all demonstrated clinically viable shear strength values. The BET adsorption method could be a valuable tool in enhancing our understanding of enamel characteristics. Our findings indicate that distinct quantitative changes in enamel pore architecture are evident after etching. Further testing with a larger sample size would have to be carried out for more definitive conclusions to be made.

  6. The influence of marketing on the sports betting attitudes and consumption behaviours of young men: implications for harm reduction and prevention strategies.

    Science.gov (United States)

    Deans, Emily G; Thomas, Samantha L; Derevensky, Jeffrey; Daube, Mike

    2017-01-19

    Gambling can cause significant health and social harms for individuals, their families, and communities. While many studies have explored the individual factors that may lead to and minimise harmful gambling, there is still limited knowledge about the broader range of factors that may contribute to gambling harm. There are significant regulations to prevent the marketing of some forms of gambling but comparatively limited regulations relating to the marketing of newer forms of online gambling such as sports betting. There is a need for better information about how marketing strategies may be shaping betting attitudes and behaviours and the range of policy and regulatory responses that may help to prevent the risky or harmful consumption of these products. We conducted qualitative, semi-structured interviews with 50 Australian men (aged 20-37 years) who gambled on sports. We explored their attitudes and opinions regarding sports betting marketing, the embedding of marketing within sports and other non-gambling community environments, and the implications this had for the normalisation of betting. Our findings indicate that most of the environments in which participants reported seeing or hearing betting advertisements were not in environments specifically designed for betting. Participants described that the saturation of marketing for betting products, including through sports-based commentary and sports programming, normalised betting. Participants described that the inducements offered by the industry were effective marketing strategies in getting themselves and other young men to bet on sports. Inducements were also linked with feelings of greater control over betting outcomes and stimulated some individuals to sign up with more than one betting provider. This research suggests that marketing plays a strong role in the normalisation of gambling in sports. This has the potential to increase the risks and subsequent harms associated with these products

  7. Surface area of lactose and lactose granulates on consolidation and compaction

    NARCIS (Netherlands)

    Riepma, Klaas Alouis

    1993-01-01

    This dissertation discusses the effect of short time storage at different conditions on the strength and the specific BET surface area of lactose tablets. In addition, some aspects are studied of the consolidation and compaction properties of crystalline lactose fractions in heterogeneous systems.

  8. BET Bromodomain Inhibition Synergizes with PARP Inhibitor in Epithelial Ovarian Cancer

    Directory of Open Access Journals (Sweden)

    Sergey Karakashev

    2017-12-01

    Full Text Available PARP inhibition is known to be an effective clinical strategy in BRCA mutant cancers, but PARP inhibition has not been applied to BRCA-proficient tumors. Here, we show the synergy of BET bromodomain inhibition with PARP inhibition in BRCA-proficient ovarian cancers due to mitotic catastrophe. Treatment of BRCA-proficient ovarian cancer cells with the BET inhibitor JQ1 downregulated the G2-M cell-cycle checkpoint regulator WEE1 and the DNA-damage response factor TOPBP1. Combining PARP inhibitor Olaparib with the BET inhibitor, we observed a synergistic increase in DNA damage and checkpoint defects, which allowed cells to enter mitosis despite the accumulation of DNA damage, ultimately causing mitotic catastrophe. Moreover, JQ1 and Olaparib showed synergistic suppression of growth of BRCA-proficient cancer in vivo in a xenograft ovarian cancer mouse model. Our findings indicate that a combination of BET inhibitor and PARP inhibitor represents a potential therapeutic strategy for BRCA-proficient cancers.

  9. Design, Synthesis, and Biological Activity of 1,2,3-Triazolobenzodiazepine BET Bromodomain Inhibitors.

    Science.gov (United States)

    Sharp, Phillip P; Garnier, Jean-Marc; Hatfaludi, Tamas; Xu, Zhen; Segal, David; Jarman, Kate E; Jousset, Hélène; Garnham, Alexandra; Feutrill, John T; Cuzzupe, Anthony; Hall, Peter; Taylor, Scott; Walkley, Carl R; Tyler, Dean; Dawson, Mark A; Czabotar, Peter; Wilks, Andrew F; Glaser, Stefan; Huang, David C S; Burns, Christopher J

    2017-12-14

    A number of diazepines are known to inhibit bromo- and extra-terminal domain (BET) proteins. Their BET inhibitory activity derives from the fusion of an acetyl-lysine mimetic heterocycle onto the diazepine framework. Herein we describe a straightforward, modular synthesis of novel 1,2,3-triazolobenzodiazepines and show that the 1,2,3-triazole acts as an effective acetyl-lysine mimetic heterocycle. Structure-based optimization of this series of compounds led to the development of potent BET bromodomain inhibitors with excellent activity against leukemic cells, concomitant with a reduction in c- MYC expression. These novel benzodiazepines therefore represent a promising class of therapeutic BET inhibitors.

  10. Extracting local information from crowds through betting markets

    Science.gov (United States)

    Weijs, Steven

    2015-04-01

    In this research, a set-up is considered in which users can bet against a forecasting agency to challenge their probabilistic forecasts. From an information theory standpoint, a reward structure is considered that either provides the forecasting agency with better information, paying the successful providers of information for their winning bets, or funds excellent forecasting agencies through users that think they know better. Especially for local forecasts, the approach may help to diagnose model biases and to identify local predictive information that can be incorporated in the models. The challenges and opportunities for implementing such a system in practice are also discussed.

  11. Allergy immunotherapy with a hypoallergenic recombinant birch pollen allergen rBet v 1-FV in a randomized controlled trial.

    Science.gov (United States)

    Klimek, Ludger; Bachert, Claus; Lukat, Karl-Friedrich; Pfaar, Oliver; Meyer, Hanns; Narkus, Annemie

    2015-01-01

    Pollen extracts and chemically modified allergoids are used successfully in allergen immunotherapy (AIT). Recombinant extracts offer potential advantages with respect to pharmaceutical quality, standardization and dosing. A hypoallergenic recombinant folding variant of the major birch pollen allergen (rBet v 1-FV) was compared with an established native birch preparation. A pre-seasonal, randomized, actively controlled phase II study was performed in birch pollen allergic rhino-conjunctivitis with or without asthma, GINA I/ II. 51 patients (24 rBet v 1-FV, 27 native extract) started therapy with subcutaneous allergen immunotherapy (SCIT). Primary end-point was a combined symptom medication score (SMS), changes in nasal provocation test, visual rating score and specific antibody responses secondary end-points. After one pre-seasonal treatment course the combined SMS was 5.86 (median; IQR: 14.02) for the rBet v 1-FV group versus 12.40 (median; IQR: 9.32) for the comparator during the three weeks pollen season (p = 0.330). After treatment in the second year, scores were 3.00 (median; IQR: 6.50) and 2.93 (4.86) respectively. Allergen tolerance in a nasal provocation test improved to a comparable extent in both groups. Significant increases in birch pollen-specific IgG1 and IgG4 were observed in both treatment groups following the first treatment phase and remained significantly raised until the end of the study. In this first in man, proof of concept phase II trial no statistical difference between rBet v 1-FV and an established natural pollen extract could be observed. rBet v 1-FV could be administered in higher doses than the native protein with no increase in adverse effects. The study was registered in clinicalTrials.gov (NCT00266526).

  12. The Bet v 1 fold: an ancient, versatile scaffold for binding of large, hydrophobic ligands

    Directory of Open Access Journals (Sweden)

    Breiteneder Heimo

    2008-10-01

    Full Text Available Abstract Background The major birch pollen allergen, Bet v 1, is a member of the ubiquitous PR-10 family of plant pathogenesis-related proteins. In recent years, a number of diverse plant proteins with low sequence similarity to Bet v 1 was identified. In addition, determination of the Bet v 1 structure revealed the existence of a large superfamily of structurally related proteins. In this study, we aimed to identify and classify all Bet v 1-related structures from the Protein Data Bank and all Bet v 1-related sequences from the Uniprot database. Results Structural comparisons of representative members of already known protein families structurally related to Bet v 1 with all entries of the Protein Data Bank yielded 47 structures with non-identical sequences. They were classified into eleven families, five of which were newly identified and not included in the Structural Classification of Proteins database release 1.71. The taxonomic distribution of these families extracted from the Pfam protein family database showed that members of the polyketide cyclase family and the activator of Hsp90 ATPase homologue 1 family were distributed among all three superkingdoms, while members of some bacterial families were confined to a small number of species. Comparison of ligand binding activities of Bet v 1-like superfamily members revealed that their functions were related to binding and metabolism of large, hydrophobic compounds such as lipids, hormones, and antibiotics. Phylogenetic relationships within the Bet v 1 family, defined as the group of proteins with significant sequence similarity to Bet v 1, were determined by aligning 264 Bet v 1-related sequences. A distance-based phylogenetic tree yielded a classification into 11 subfamilies, nine exclusively containing plant sequences and two subfamilies of bacterial proteins. Plant sequences included the pathogenesis-related proteins 10, the major latex proteins/ripening-related proteins subfamily, and

  13. Internet-based structural characteristics of sports betting and problem gambling severity: is there a relationship?

    OpenAIRE

    Lopez-Gonzalez, H; Estévez, A; Griffiths, MD

    2018-01-01

    With the adoption and popularization of internet-based platforms, sports betting has introduced new functionalities that transform the design of its products and therefore the way bettors interact with them. This study aims to explore the association between the use of new structural characteristics of online betting and gambling severity. Five characteristics are examined here: (i) live in-play betting; (ii) cash out feature use (as example of in-play betting in-built features); (iii) fantas...

  14. Asthma: T-bet — A Master Controller?

    OpenAIRE

    Robinson, Douglas S; Lloyd, Clare M

    2002-01-01

    The transcription factors T-bet and GATA3 are important reciprocal determinants of Th1 and Th2 T helper cell differentiation. Recent evidence suggests that these factors may affect airway immunopathology in asthma.

  15. [Forms of pathological gambling: empirical research on consumers behaviour of sport betting and lottery participants].

    Science.gov (United States)

    Plöntzke, Babett; Albrecht, Ulrike; Thalemann, Carolin; Grüsser, Sabine Miriam

    2004-08-01

    Gambling is one of the favourite leisure activities. 70-90 % of the grown-up population have gambled at least once in their life. Over the last few years, however, the variety of opportunities to gamble has changed. Decreasing numbers of casino visitors can be seen against an ever-increasing number of people using slot machines, and taking part in national lotteries and sport betting. Comprehensive empirical research regarding consumer behaviour and addiction potential involved in sport betting has been non-existent and only a few studies have dealt with lottery. In the present study, 108 subjects were questioned in Austrian betting offices. 33.3 % of the sample fulfilled the diagnostic criteria for pathological sport betting. Of the sport betting subjects who additionally play lottery, 22.92 % were diagnosed as being pathological lottery gamblers. Based on the criteria of substance addiction, the data demonstrate that sport betting and lottery have addiction potential and can therefore be seen as non-substance-related addiction.

  16. The impact of nitration on the structure and immunogenicity of the major birch pollen allergen Bet v 1.0101.

    Directory of Open Access Journals (Sweden)

    Chloé Ackaert

    Full Text Available Allergy prevalence has increased in industrialized countries. One contributing factor could be pollution, which can cause nitration of allergens exogenously (in the air or endogenously (in inflamed lung tissue. We investigated the impact of nitration on both the structural and immunological behavior of the major birch pollen allergen Bet v 1.0101 to determine whether nitration might be a factor in the increased incidence of allergy. Bet v 1.0101 was nitrated with tetranitromethane. Immune effects were assessed by measuring the proliferation of specific T-cell lines (TCLs upon stimulation with different concentrations of nitrated and unmodified allergen, and by measurement of cytokine release of monocyte-derived dendritic cells (moDCs and primary DCs (primDCs stimulated with nitrated versus unmodified allergen. HPLC-MS, crystallography, gel electrophoresis, amino acid analysis, size exclusion chromatography and molecular dynamics simulation were performed to characterize structural changes after nitration of the allergen. The proliferation of specific TCLs was higher upon stimulation with the nitrated allergen in comparison to the unmodified allergen. An important structural consequence of nitration was oligomerization. Moreover, analysis of the crystal structure of nitrated Bet v 1.0101 showed that amino acid residue Y83, located in the hydrophobic cavity, was nitrated to 100%. Both moDCs and primDCs showed decreased production of TH1-priming cytokines, thus favoring a TH2 response. These results implicate that nitration of Bet v 1.0101 might be a contributing factor to the observed increase in birch pollen allergy, and emphasize the importance of protein modifications in understanding the molecular basis of allergenicity.

  17. Predicting sports betting outcomes

    OpenAIRE

    Flis, Borut

    2014-01-01

    We wish to build a model, which could predict the outcome of basketball games. The goal was to achieve an sufficient enough accuracy to make a profit in sports betting. One learning example is a game in the NBA regular season. Every example has multiple features, which describe the opposing teams. We tried many methods, which return the probability of the home team winning and the probability of the away team winning. These probabilities are used for risk analysis. We used the best model in h...

  18. Applicability of the Guggenheim–Anderson–Boer water vapour sorption model for estimation of soil specific surface area

    DEFF Research Database (Denmark)

    Arthur, Emmanuel; Tuller, Markus; Møldrup, Per

    2018-01-01

    Soil specific surface area (SA) controls fundamental soil processes such as retention of water, ion exchange, and adsorption and release of plant nutrients and contaminants. Conventional methods for determining SA include adsorption of polar or non‐polar fluid molecules with associated advantages...... parameters varied depending on the water activity or relative humidity range of measured data (0.03–0.93 compared with 0.10–0.80), whereas the variation for desorption was minimal. For desorption isotherms, the average water activity value at which the GAB monolayer parameter was obtained was 0......‐based modelling approaches to determine SA. Measured water vapour adsorption and desorption isotherms for 321 soil samples were used to parameterize the GAB model, the Brunauer–Emmet–Teller (BET) equation and a film adsorption Tuller–Or (TO) model to estimate SA. For adsorption isotherms, the values of the GAB...

  19. Return on securities of the listed banks, using BET and BET-C indices of the Bucharest Stock Exchange

    Directory of Open Access Journals (Sweden)

    Victoria FIRESCU

    2017-11-01

    Full Text Available The present work has great importance for the economic and financial area due to the fact that targets the relevance of the financial indicators in anticipation of the stock variation. The aim is to measure the correlation, the type and intensity, between the variation of stock market profitability and the profitability of the securities traded by banks in Romania, listed on the BSE. The research is approached transversely (banks in Romania listed on the stock market as well as longitudinally (from the date of listing on the Stock Exchange of each bank until 31.12.2016. Using the econometric model Eviews we tested the correlation between the profitability of BRD, BT, BCC bank`s securities and the profitability of Bucharest Stock Exchange, by BET and BET-C. The results show that the research hypothesis isn’t validated for any of those banks.

  20. Betting Decision Under Break-Streak Pattern: Evidence from Casino Gaming.

    Science.gov (United States)

    Fong, Lawrence Hoc Nang; So, Amy Siu Ian; Law, Rob

    2016-03-01

    Cognitive bias is prevalent among gamblers, especially those with gambling problems. Grounded in the heuristics theories, this study contributes to the literature by examining a cognitive bias triggered by the break streak pattern in the casino setting. We postulate that gamblers tend to bet on the latest outcome when there is a break-streak pattern. Moreover, three determinants of the betting decision under break-streak pattern, including the streak length of the alternative outcome, the frequency of the latest outcome, and gender, were identified and examined in this study. A non-participatory observational study was conducted among the Cussec gamblers in a casino in Macao. An analysis of 1229 bets confirms our postulation, particularly when the streak of the alternative outcome is long, the latest outcome is frequent, and the gamblers are females. The findings provide meaningful implications for casino management and public policymakers regarding the minimization of gambling harm.

  1. 'A place for men to come and do their thing': constructing masculinities in betting shops in London.

    Science.gov (United States)

    Cassidy, Rebecca

    2014-03-01

    During fieldwork conducted with workers and customers in betting shops in London research participants consistently conceptualized betting shops as masculine spaces in contrast to the femininity of other places including home and the bingo hall. According to this argument, betting on horses and dogs was 'men's business' and betting shops were 'men's worlds'. Two explanations were offered to account for this situation. The first suggested that betting was traditionally a pastime enjoyed by men rather than women. The second was that betting is intrinsically more appealing to men because it is based on calculation and measurement, and women prefer more intuitive, simpler challenges. I use interviews with older people to describe how the legalisation of betting in cash in 1961 changed the geography of betting. I then draw upon interviews with regular customers in order to show how knowledge about betting is shared within rather than between genders. Finally, I use my experience of training and working as a cashier to describe how the particular hegemonic masculinity found in betting shops in London is maintained through myriad everyday practices which reward certain kinds of gendered performances while at the same time suppressing alternatives. The article shows how particular spaces may become gendered as an unanticipated consequence of legislation and how contingent gendered associations are both naturalized and, at the same time, subjected to intense attention. © London School of Economics and Political Science 2013.

  2. Betting Against Beta

    DEFF Research Database (Denmark)

    Frazzini, Andrea; Heje Pedersen, Lasse

    We present a model with leverage and margin constraints that vary across investors and time. We find evidence consistent with each of the model’s five central predictions: (1) Since constrained investors bid up high-beta assets, high beta is associated with low alpha, as we find empirically for U...... of the BAB factor is low; (4) Increased funding liquidity risk compresses betas toward one; (5) More constrained investors hold riskier assets........S. equities, 20 international equity markets, Treasury bonds, corporate bonds, and futures; (2) A betting-against-beta (BAB) factor, which is long leveraged low beta assets and short high-beta assets, produces significant positive risk-adjusted returns; (3) When funding constraints tighten, the return...

  3. Complexity Triggered by Economic Globalisation— The Issue of On-Line Betting-Related Match Fixing

    Directory of Open Access Journals (Sweden)

    Wladimir Andreff

    2017-02-01

    Full Text Available Complexity in mainstream economics consists in high intermediary consumption of mathematics. A new approach to complexity economics dwells upon path-dependent global systems; their emergence and evolving organisation. The focus here is on the complexity of the real economic world due to globalisation. On-line betting related match-fixing is a case in point about which the article presents non-exhaustive empirical evidence and shows how it is analysed with the standard model of the economics of crime. There is no room for complexity in such an individualistic approach to corrupt behaviour applied to bet-related fixes. A more complex model is sketched based on interactions between a global (though underground market for fixes and the actual partly legal, partly illegal global sport betting market. These interactions exhibit how complex is the issue of combating betting-related match fixing. Reviewing those major policies envisaged for containing the latter—prohibition; sanctions; regulation; privatisation (betting rights—the article opts for a global ‘Sportbettobin’ tax on sport betting gains; in the same vein as the famous Tobin tax on international capital transfers. The novelty in this approach is a variable (increasing rate applied to increasing tranches of taxation (gains which should dry up the worst cases of on-line bettingrelated match fixing.

  4. A molecular threshold for effector CD8(+) T cell differentiation controlled by transcription factors Blimp-1 and T-bet.

    Science.gov (United States)

    Xin, Annie; Masson, Frederick; Liao, Yang; Preston, Simon; Guan, Tianxia; Gloury, Renee; Olshansky, Moshe; Lin, Jian-Xin; Li, Peng; Speed, Terence P; Smyth, Gordon K; Ernst, Matthias; Leonard, Warren J; Pellegrini, Marc; Kaech, Susan M; Nutt, Stephen L; Shi, Wei; Belz, Gabrielle T; Kallies, Axel

    2016-04-01

    T cell responses are guided by cytokines that induce transcriptional regulators, which ultimately control differentiation of effector and memory T cells. However, it is unknown how the activities of these molecular regulators are coordinated and integrated during the differentiation process. Using genetic approaches and transcriptional profiling of antigen-specific CD8(+) T cells, we reveal a common program of effector differentiation that is regulated by IL-2 and IL-12 signaling and the combined activities of the transcriptional regulators Blimp-1 and T-bet. The loss of both T-bet and Blimp-1 leads to abrogated cytotoxic function and ectopic IL-17 production in CD8(+) T cells. Overall, our data reveal two major overlapping pathways of effector differentiation governed by the availability of Blimp-1 and T-bet and suggest a model for cytokine-induced transcriptional changes that combine, quantitatively and qualitatively, to promote robust effector CD8(+) T cell differentiation.

  5. The impact of near-miss events on betting behavior: An examination of casino rapid roulette play

    Directory of Open Access Journals (Sweden)

    James A. Sundali

    2012-11-01

    Full Text Available We examine how almost winning in roulette affects subsequent betting behavior. Our main finding is heterogeneity in gambler behavior with some gamblers less likely to bet on numbers that were near misses on the prior spin and other gamblers more likely to bet on near miss numbers. Using a unique data set from the game rapid roulette, we model the likelihood of a gambler betting on a near miss number while controlling for the favorite number bias and the likelihood of a number being a near miss. We also find no evidence that near misses in roulette leads to gamblers extending the time spent gambling or to the placing of more bets.

  6. Daring the Foolish to Take Darwin Tests: The Ethical Double Bind of Betting On Natural Hazards

    Science.gov (United States)

    Halpern, J. B.

    2017-12-01

    While couched in the framework of concentrating minds betting on natural hazards carries an ethical cost. When children dare each other to do risky things parents know that when such dares are taken harm frequently occurs. Giving those who claim that there is no hazard financial reasons to avoid ameliorative actions or to double down in support of their public stance requires a moral calculation. Challenging the conclusions of those who accept such bets while denying danger will lead them to attempt to save face by increasing risk to themselves or others. Thus such wagers, whether person to person or on betting markets, require balancing between alerting the opposing party and others to the risks of not taking action, the associated scientific consensus and the possible harmful outcomes of the bets themselves. This talk will describe strategies for minimizing potential harm while maximizing the instructive component of climate bets. Best practices include having the bet rest on a technical issue that can be authoritatively resolved in a short time. Unfortunately the nature of natural hazard risks makes it difficult to meet all of these criteria, but those making such bets should be aware of the ethical double bind

  7. Effects of Shen-Fu Injection on the Expression of T-Cell-Specific Transcription Factors T-bet/Gata-3 in Porcine Postresuscitation Lung Injury

    Directory of Open Access Journals (Sweden)

    Wei Gu

    2013-01-01

    Full Text Available Shen-Fu injection (SFI derived from the ancient traditional Chinese medicine. In this study, the effects of SFI on the expression of T-bet/GATA-3 and its potential mechanisms causing the shift of T cells from Th2 to Th1 on postresuscitation lung injury were examined in a porcine model of cardiac arrest. 30 pigs were randomly divided into SHAM ( and three return of spontaneous circulation (ROSC groups ( per group; 24 pigs were subjected to 8 min of electrically induced cardiac arrest and 2 min of basic life support, which received central venous injection of Shen-Fu (SFI, epinephrine (EP or saline (SA. After successful ROSC, 18 surviving pigs were sacrificed at 24 h after ROSC ( per group. The levels of serum and lung tissue interleukin (IL-4 and interferon (IFN-γ were measured by ELISA, and the protein and mRNA levels of GATA-3 and T-bet in the lung tissue were determined by western blotting and quantitative real-time polymerase chain reaction, respectively. Compared with the EP and SA groups, SFI treatment reduced the levels of IL-4 (, increased levels of IFN-γ (, and induced T-bet mRNA upregulation and GATA-3 mRNA downregulation (. SFI attenuated lung injury and regulated lung immune disorders. Therefore, SFI could protect postresuscitation lung injury by modulating a Th1/Th2 imbalance.

  8. The Structural Features of Sports and Race Betting Inducements: Issues for Harm Minimisation and Consumer Protection.

    Science.gov (United States)

    Hing, Nerilee; Sproston, Kerry; Brook, Kate; Brading, Richard

    2017-06-01

    Minimal research has been published about inducements for sports and race betting, despite their ready availability and aggressive advertising. This paper aimed to document the range and structural features of these inducements, and analyse their alignment with the harm minimisation and consumer protection goals of responsible gambling. A scan of all inducements offered on the websites of 30 major race and sports betting brands located 223 separate inducements which we categorised into 15 generic types, all offering financial incentives to purchase. These comprised sign-up offers, refer-a-friend offers, happy hours, mobile betting bonuses, multi-bet offers, refund/stake-back offers, matching stakes/deposits, winnings paid for 'close calls', bonus or better odds, bonus or better winnings, competitions, reduced commission, free bets to selected punters, cash rebates and other free bets. All inducements were subject to numerous terms and conditions which were complex, difficult to find, and obscured by legalistic language. Play-through conditions of bonus bets were particularly difficult to interpret and failed basic requirements for informed choice. Website advertisements for inducements were prominently promoted but few contained a responsible gambling message. The results were analysed to generate 12 research propositions considered worthy of empirical research to inform much needed regulatory reform in this area.

  9. Synthesis of MOF having hydroxyl functional side groups and optimization of activation process for the maximization of its BET surface area

    International Nuclear Information System (INIS)

    Kim, Jongsik; Kim, Dong Ok; Kim, Dong Wook; Sagong, Kil

    2013-01-01

    To accomplish the postsynthetic modification of MOF with organic-metal precursors (OMPs) described in our previous researches more efficiently, synthesis of MOF (HCC-2) possessing relatively larger pore size as well as higher number of hydroxyl functional side groups per its base unit than those of HCC-1 has been successfully conducted via adopting 1,4-di-(4-carboxy-2,6-dihydroxyphenyl)benzene as an organic ligand and Zn(NO 3 ) 2 ·6H 2 O as a metal source, respectively. Also, optimization about the Activation process of HCC-2 was performed to maximize its BET (Brunauer–Emmett–Teller) surface area which was proved to be proportional to the number of exposed active sites on which its postsynthetic modification occurred. However, Activation process having been validated to be so effective with the acquirement of highly-purified HCC-1 (CO 2 supercritical drying step followed by vacuum drying step) was less satisfactory with the case of HCC-2. This might be attributed to relatively higher hydrophilicity and bulkier molecular structure of organic ligand of HCC-2. However, it was readily settled by simple modification of above Activation process. Moreover, indispensable residues composed of both DMF and its thermally degraded derivatives which were chemically attached via coordination bond with hydroxyl functionalities even after Activation process III might enable their H 2 adsorption properties to be seriously debased compared to that of IRMOF-16 having no hydroxyl functionalities. - Graphical abstract: Synthesis of new-structured MOF (HCC-2) simultaneously possessing relatively larger pore size as well as higher number of hydroxyl functional side groups per its base unit at the same time than those of HCC-1 has been performed via adopting 1,4-di-(4-carboxy-2,6-dihydroxyphenyl)benzene as an organic ligand and Zn(NO 3 ) 2 ·6H 2 O as a metal source, respectively. Also, the optimization of activation process for HCC-2 was conducted to maximize its BET surface area

  10. Bet-hedging response to environmental variability, an intraspecific comparison.

    Science.gov (United States)

    Nevoux, Marie; Forcada, Jaume; Barbraud, Christophe; Croxall, John; Weimerskirchi, Henri

    2010-08-01

    A major challenge in ecology is to understand the impact of increased environmental variability on populations and ecosystems. To maximize their fitness in a variable environment, life history theory states that individuals should favor a bet-hedging strategy, involving a reduction of annual breeding performance and an increase in adult survival so that reproduction can be attempted over more years. As a result, evolution toward longer life span is expected to reduce the deleterious effects of extra variability on population growth, and consequently on the trait contributing the most to it (e.g., adult survival in long-lived species). To investigate this, we compared the life histories of two Black-browed Albatross (Thalassarche melanophrys) populations breeding at South Georgia (Atlantic Ocean) and Kerguelen (Indian Ocean), the former in an environment nearly three times more variable climatically (e.g., in sea surface temperature) than the latter. As predicted, individuals from South Georgia (in the more variable environment) showed significantly higher annual adult survival (0.959, SE = 0.003) but lower annual reproductive success (0.285 chick per pair, SE = 0.039) than birds from Kerguelen (survival = 0.925, SE = 0.004; breeding success = 0.694, SE = 0.027). In both populations, climatic conditions affected the breeding success and the survival of inexperienced breeders, whereas the survival of experienced breeders was unaffected. The strength of the climatic impact on survival of inexperienced breeders was very similar between the two populations, but the effect on breeding success was positively related to environmental variability. These results provide rare and compelling evidence to support bet-hedging underlying changes in life history traits as an adaptive response to environmental variability.

  11. The Role of Protein Modifications of T-Bet in Cytokine Production and Differentiation of T Helper Cells

    Directory of Open Access Journals (Sweden)

    Sera Oh

    2014-01-01

    Full Text Available T-Bet (T-box protein expressed in T cells, also called as TBX21 was originally cloned as a key transcription factor involved in the commitment of T helper (Th cells to the Th1 lineage. T-Bet directly activates IFN-γ gene transcription and enhances development of Th1 cells. T-Bet simultaneously modulates IL-2 and Th2 cytokines in an IFN-γ-independent manner, resulting in an attenuation of Th2 cell development. Numerous studies have demonstrated that T-bet plays multiple roles in many subtypes of immune cells, including B cell, dendritic cells, natural killer (NK cells, NK T cells, and innate lymphoid cells. Therefore, T-bet is crucial for the development and coordination of both innate and adaptive immune responses. To fulfill these multiple roles, T-bet undergoes several posttranslational protein modifications, such as phosphorylation at tyrosine, serine, and threonine residues, and ubiquitination at lysine residues, which affect lineage commitment during Th cell differentiation. This review presents a current overview of the progress made in understanding the roles of various types of T-bet protein modifications in the regulation of cytokine production during Th cell differentiation.

  12. Efficacy and safety of 4 months of sublingual immunotherapy with recombinant Mal d 1 and Bet v 1 in patients with birch pollen-related apple allergy.

    Science.gov (United States)

    Kinaciyan, Tamar; Nagl, Birgit; Faustmann, Sandra; Frommlet, Florian; Kopp, Stephan; Wolkersdorfer, Martin; Wöhrl, Stefan; Bastl, Katharina; Huber, Hans; Berger, Uwe; Bohle, Barbara

    2018-03-01

    Birch pollen-related apple allergy is among the most prevalent food allergies in adolescent/adult subjects and mainly results from sensitization to the major birch pollen allergen Bet v 1 and subsequent cross-reaction with the apple protein Mal d 1. However, specific immunotherapy with birch pollen has inconsistent effects on apple allergy. We sought to compare the safety and efficacy of sublingual immunotherapy (SLIT) with 2 formulations containing either rMal d 1 or rBet v 1 on birch pollen-related apple allergy. Sixty participants with birch pollen-related apple allergy were randomized to daily sublingual application of placebo (n = 20) or 25 μg of rMal d 1 (n = 20) or rBet v 1 (n = 20) for 16 weeks. Adverse events were regularly recorded. Sublingual challenges with standardized doses of rMal d 1, skin prick tests with recombinant allergens, and measurements of allergen-specific IgE and IgG 4 antibodies were performed before and after treatment. Both formulations caused comparable, mainly local adverse events. No systemic reactions occurred. Compared with the placebo and rBet v 1-treated groups, SLIT with rMal d 1 reduced rMal d 1-induced oral symptoms (P = .001 and P = .038) accompanied by longitudinally reduced rMal d 1-specific cutaneous reactions (P = .022) and enhanced IgG 4 /IgE ratios (P = .012). SLIT with rBet v 1 neither improved the clinical reactivity to rMal d 1 nor enhanced rMal d 1-specific IgG 4 /IgE ratios. Participants receiving placebo showed no allergen-specific changes. Sublingual treatment with a recombinant food allergen was safe and clinically effective, as determined by using standardized challenges. We present a promising approach for the effective treatment of birch pollen-related apple allergy. Copyright © 2017 American Academy of Allergy, Asthma & Immunology. Published by Elsevier Inc. All rights reserved.

  13. Bet hedging in yeast by heterogeneous, age-correlated expression of a stress protectant.

    Directory of Open Access Journals (Sweden)

    Sasha F Levy

    Full Text Available Genetically identical cells grown in the same culture display striking cell-to-cell heterogeneity in gene expression and other traits. A crucial challenge is to understand how much of this heterogeneity reflects the noise tolerance of a robust system and how much serves a biological function. In bacteria, stochastic gene expression results in cell-to-cell heterogeneity that might serve as a bet-hedging mechanism, allowing a few cells to survive through an antimicrobial treatment while others perish. Despite its clinical importance, the molecular mechanisms underlying bet hedging remain unclear. Here, we investigate the mechanisms of bet hedging in Saccharomyces cerevisiae using a new high-throughput microscopy assay that monitors variable protein expression, morphology, growth rate, and survival outcomes of tens of thousands of yeast microcolonies simultaneously. We find that clonal populations display broad distributions of growth rates and that slow growth predicts resistance to heat killing in a probabalistic manner. We identify several gene products that are likely to play a role in bet hedging and confirm that Tsl1, a trehalose-synthesis regulator, is an important component of this resistance. Tsl1 abundance correlates with growth rate and replicative age and predicts survival. Our results suggest that yeast bet hedging results from multiple epigenetic growth states determined by a combination of stochastic and deterministic factors.

  14. Pinkfoot (kortnæbet gås)

    DEFF Research Database (Denmark)

    2008-01-01

    Database over indberetninger af observationer af Pinkfooted geese (Kortnæbet gås). Gæssene er mærket med halsringe eller fodringe (unger), som kan ses med kikkert. Observatør kan efterflg. indtaste tid og sted for observationen på hjemmeside eller indsende samlet liste. Hjemmesiden giver overblik...

  15. T-bet-mediated Tim-3 expression dampens monocyte function during chronic hepatitis C virus infection.

    Science.gov (United States)

    Yi, Wenjing; Zhang, Peixin; Liang, Yan; Zhou, Yun; Shen, Huanjun; Fan, Chao; Moorman, Jonathan P; Yao, Zhi Q; Jia, Zhansheng; Zhang, Ying

    2017-03-01

    Hepatitis C virus (HCV) induces a high rate of chronic infection via dysregulation of host immunity. We have previously shown that T-cell immunoglobulin and mucin domain protein-3 (Tim-3) is up-regulated on monocyte/macrophages (M/Mφ) during chronic HCV infection; little is known, however, about the transcription factor that controls its expression in these cells. In this study, we investigated the role of transcription factor, T-box expressed in T cells (T-bet), in Tim-3 expression in M/Mφ in the setting of HCV infection. We demonstrate that T-bet is constitutively expressed in resting CD14 + M/Mφ in the peripheral blood. M/Mφ from chronically HCV-infected individuals exhibit a significant increase in T-bet expression that positively correlates with an increased level of Tim-3 expression. Up-regulation of T-bet is also observed in CD14 + M/Mφ incubated with HCV + Huh7.5 cells, as well as in primary M/Mφ or monocytic THP-1 cells exposed to HCV core protein in vitro, which is reversible by blocking HCV core/gC1qR interactions. Moreover, the HCV core-induced up-regulation of T-bet and Tim-3 expression in M/Mφ can be abrogated by incubating the cells with SP600125 - an inhibitor for the c-Jun N-terminal kinase (JNK) signalling pathway. Importantly, silencing T-bet gene expression decreases Tim-3 expression and enhances interleukin-12 secretion as well as signal transducer and activator of transcription 1 phosphorylation. These data suggest that T-bet, induced by the HCV core/gC1qR interaction, enhances Tim-3 expression via the JNK pathway, leading to dampened M/Mφ function during HCV infection. These findings reveal a novel mechanism for Tim-3 regulation via T-bet during HCV infection, providing new targets to combat this global epidemic viral disease. © 2016 John Wiley & Sons Ltd.

  16. Tackling Bet v 1 and associated food allergies with a single hybrid protein.

    Science.gov (United States)

    Hofer, Heidi; Asam, Claudia; Hauser, Michael; Nagl, Birgit; Laimer, Josef; Himly, Martin; Briza, Peter; Ebner, Christof; Lang, Roland; Hawranek, Thomas; Bohle, Barbara; Lackner, Peter; Ferreira, Fátima; Wallner, Michael

    2017-08-01

    Allergy vaccines should be easily applicable, safe, and efficacious. For Bet v 1-mediated birch pollen and associated food allergies, a single wild-type allergen does not provide a complete solution. We aimed to combine immunologically relevant epitopes of Bet v 1 and the 2 clinically most important related food allergens from apple and hazelnut to a single hybrid protein, termed MBC4. After identification of T cell epitope-containing parts on each of the 3 parental allergens, the hybrid molecule was designed to cover relevant epitopes and evaluated in silico. Thereby a mutation was introduced into the hybrid sequence, which should alter the secondary structure without compromising the immunogenic properties of the molecule. MBC4 and the parental allergens were purified to homogeneity. Analyses of secondary structure elements revealed substantial changes rendering the hybrid de facto nonreactive with patients' serum IgE. Nevertheless, the protein was monomeric in solution. MBC4 was able to activate T-cell lines from donors with birch pollen allergy and from mice immunized with the parental allergens. Moreover, on immunization of mice and rabbits, MBC4 induced cross-reactive IgG antibodies, which were able to block the binding of human serum IgE. Directed epitope rearrangements combined with a knowledge-based structural modification resulted in a protein unable to bind IgE from allergic patients. Still, properties to activate specific T cells or induce blocking antibodies were conserved. This suggests that MBC4 is a suitable vaccine candidate for the simultaneous treatment of Bet v 1 and associated food allergies. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

  17. IFNγ signaling endows DCs with the capacity to control type I inflammation during parasitic infection through promoting T-bet+ regulatory T cells.

    Directory of Open Access Journals (Sweden)

    Hyang-Mi Lee

    2015-02-01

    Full Text Available IFNγ signaling drives dendritic cells (DCs to promote type I T cell (Th1 immunity. Here, we show that activation of DCs by IFNγ is equally crucial for the differentiation of a population of T-bet+ regulatory T (Treg cells specialized to inhibit Th1 immune responses. Conditional deletion of IFNγ receptor in DCs but not in Treg cells resulted in a severe defect in this specific Treg cell subset, leading to exacerbated immune pathology during parasitic infections. Mechanistically, IFNγ-unresponsive DCs failed to produce sufficient amount of IL-27, a cytokine required for optimal T-bet induction in Treg cells. Thus, IFNγ signalling endows DCs with the ability to efficiently control a specific type of T cell immunity through promoting a corresponding Treg cell population.

  18. Photocatalytic Activity in CH3CN Related to the Surface Properties of TiO2 Powders Prepared by Sol-Gel Method

    Directory of Open Access Journals (Sweden)

    Marta Bettoni

    2009-01-01

    Full Text Available Some TiO2 powders, prepared from titanium(IVtetraisopropoxide by the sol-gel method and thermally treated between 100 and 1000∘C, have been characterized by X-ray powder diffraction and by nitrogen adsorption and desorption at 77 K to calculate the BET-specific surface area, from which the micropore volume and the external surface area can be derived. The photocatalytic activity (ka of the above powders has been evaluated considering the TiO2-sensitized photo-oxidation of 4-methoxybenzyl alcohol in CH3CN as the test reaction. The decrease of ka have been related to the decrease of the BET surface area, the micropore volume, and the external surface area of the TiO2 powders, but a satisfactory linear correlation is observed only for the last superficial parameter.

  19. Maintenance of muscle myosin levels in adult C. elegans requires both the double bromodomain protein BET-1 and sumoylation

    Directory of Open Access Journals (Sweden)

    Kate Fisher

    2013-10-01

    Attenuation of RAS-mediated signalling is a conserved process essential to control cell proliferation, differentiation, and apoptosis. Cooperative interactions between histone modifications such as acetylation, methylation and sumoylation are crucial for proper attenuation in C. elegans, implying that the proteins recognising these histone modifications could also play an important role in attenuation of RAS-mediated signalling. We sought to systematically identify these proteins and found BET-1. BET-1 is a conserved double bromodomain protein that recognises acetyl-lysines on histone tails and maintains the stable fate of various lineages. Unexpectedly, adults lacking both BET-1 and SUMO-1 are depleted of muscle myosin, an essential component of myofibrils. We also show that this muscle myosin depletion does not occur in all animals at a specific time, but rather that the penetrance of the phenotype increases with age. To gain mechanistic insights into this process, we sought to delay the occurrence of the muscle myosin depletion phenotype and found that it requires caspase activity and MEK-dependent signalling. We also performed transcription profiling on these mutants and found an up-regulation of the FGF receptor, egl-15, a tyrosine kinase receptor acting upstream of MEK. Consistent with a MEK requirement, we could delay the muscle phenotype by systemic or hypodermal knock down of egl-15. Thus, this work uncovered a caspase- and MEK-dependent mechanism that acts specifically on ageing adults to maintain the appropriate net level of muscle myosin.

  20. A aplicação estrutural de betões de elevado desempenho (HPC e UHPC)

    OpenAIRE

    Fernandes, Diogo Amaro Freitas

    2011-01-01

    Dissertação para obtenção do Grau de Mestre em Engenharia Civil A evolução dos betões, na procura de estruturas com um maior tempo de vida útil, menores custos de reparação e maiores resistências tem sido alvo de pesquisa por investigadores de todo o mundo. No presente trabalho é apresentado o estado da arte dos betões de elevado desempenho (HPCHigh Performance Concrete e UHPC-Ultra High Performance Concrete), betões garantes de maior durabilidade e resistência, com o objectivo de co...

  1. Optimizing parameter choice for FSL-Brain Extraction Tool (BET) on 3D T1 images in multiple sclerosis

    DEFF Research Database (Denmark)

    Popescu, Valeriu; Battaglini, M; Hoogstrate, W S

    2012-01-01

    Brain atrophy studies often use FSL-BET (Brain Extraction Tool) as the first step of image processing. Default BET does not always give satisfactory results on 3DT1 MR images, which negatively impacts atrophy measurements. Finding the right alternative BET settings can be a difficult and time-con...

  2. Cobalt(II phthalocyanine bonded to 3-n-propylimidazole immobilized on silica gel surface: preparation and electrochemical properties

    Directory of Open Access Journals (Sweden)

    Fujiwara Sergio T.

    1999-01-01

    Full Text Available Co-Phthalocyanine complex was immobilized on 3-n-propylimidazole groups grafted on a porous SiO2 surface (specific surface area S BET = 500 m² g-1 and efficiently electrocatalyzed the oxalic acid oxidation on a carbon paste electrode surface made of this material. Intermolecular interactions of the complex species which can normally interfere in the redox process practically are not observed in the present case because of a low average surface density, delta = 4.7 x 10-13 mol cm-2 (delta = Nf/S BET, where Nf is the amount of adsorbed Co-phtalocyanine per gram of modified silica gel of the complex species material prepared. The linear response of the electrode to oxalic acid concentration, between 6.5 x 10-4 and 3.2 x 10-3 mol L-1, associated with its high chemical stability makes the covalently immobilized Co-phtalocyanine complex material very attractive in preparing a new class of chemical sensors.

  3. Effects of Surface Treatment of Activated Carbon on Its Surface and Cr(VI) Adsorption Characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Park, Soo Jin; Jang, Yu Sin [Advanced Materials Division., Korea Research Institute of Chimical Technology, Taejon (Korea)

    2001-04-01

    In this work, the effect of surface treatments on activated carbons (ACs) has been studied in the context of gas and liquid adsorption behaviors. The chemical solutions used in this experiment were 35% sodium hydroxide, and these were used for the acidic and basic treatments, respectively. The surface properties have been determined by pH, acid-base values, and FT-IR. The adsorption isotherms of Cr(VI) ion on activated carbons have been studied with the 5 mg/l concentration at ambient temperature. N{sub 2} adsorption isotherm characteristics, which include the specific surface area, micro pore volume, and microporosity, were determined by BET and Boer's-plot methods. In case of the acidic treatment of activated carbons, it was observed that the adsorption of Cr(VI) ion was more effective due to the increase acid value (or acidic functional group) of activated carbon surfaces. However, the basic treatment on activated carbons was caused no significant effects, probably due to the decreased specific surface area and total pore volume. 27 refs., 7 figs., 4 tabs.

  4. BET bromodomain inhibition reduces maturation and enhances tolerogenic properties of human and mouse dendritic cells

    NARCIS (Netherlands)

    Schilderink, Ronald; Bell, Matthew; Reginato, Eleonora; Patten, Chris; Rioja, Inmaculada; Hilbers, Francisca W.; Kabala, Pawel A.; Reedquist, Kris A.; Tough, David F.; Tak, Paul Peter; Prinjha, Rab K.; de Jonge, Wouter J.

    2016-01-01

    Transcription of inflammatory genes is tightly regulated by acetylation and deacetylation of histone tails. An inhibitor of the acetylated-lysine reader bromodomain and extra-terminal domain (BET) proteins, I-BET151, is known to counteract the induction of expression of inflammatory genes in

  5. Surface area of lactose and lactose granulates on consolidation and compaction

    OpenAIRE

    Riepma, Klaas Alouis

    1993-01-01

    This dissertation discusses the effect of short time storage at different conditions on the strength and the specific BET surface area of lactose tablets. In addition, some aspects are studied of the consolidation and compaction properties of crystalline lactose fractions in heterogeneous systems. The crystalline lactose types used are: a-lactose monohydrate, anhydrous a-lactose, crystalline B-lactose and roller dried B-lactose. ... Zie: Summary

  6. T-Bet Enhances Regulatory T Cell Fitness and Directs Control of Th1 Responses in Crescentic GN.

    Science.gov (United States)

    Nosko, Anna; Kluger, Malte A; Diefenhardt, Paul; Melderis, Simon; Wegscheid, Claudia; Tiegs, Gisa; Stahl, Rolf A K; Panzer, Ulf; Steinmetz, Oliver M

    2017-01-01

    Th1 cells are central pathogenic mediators of crescentic GN (cGN). Mechanisms responsible for Th1 cell downregulation, however, remain widely unknown. Recently, it was proposed that activation of the Th1-characteristic transcription factor T-bet optimizes Foxp3 + regulatory T (Treg) cells to counteract Th1-type inflammation. Because very little is known about the role of T-bet + Treg1 cells in inflammatory diseases, we studied the function of these cells in the nephrotoxic nephritis (NTN) model of cGN. The percentage of Treg1 cells progressively increased in kidneys of nephritic wild-type mice during the course of NTN, indicating their functional importance. Notably, naïve Foxp3 Cre xT-bet fl/fl mice, lacking Treg1 cells, showed spontaneous skewing toward Th1 immunity. Furthermore, absence of Treg1 cells resulted in aggravated NTN with selectively dysregulated renal and systemic Th1 responses. Detailed analyses of Treg cells from Foxp3 Cre xT-bet fl/fl mice revealed unaltered cytokine production and suppressive capacity. However, in competitive cotransfer experiments, wild-type Treg cells outcompeted T-bet-deficient Treg cells in terms of population expansion and expression levels of Foxp3, indicating that T-bet expression is crucial for general Treg fitness. Additionally, T-bet-deficient Treg cells lacked expression of the Th1-characteristic trafficking receptor CXCR3, which correlated with significant impairment of renal Treg infiltration. In summary, our data indicate a new subtype of Treg cells in cGN. These Treg1 cells are characterized by activation of the transcription factor T-bet, which enhances the overall fitness of these cells and optimizes their capacity to downregulate Th1 responses by inducing chemokine receptor CXCR3 expression. Copyright © 2016 by the American Society of Nephrology.

  7. Prevalence of IgE antibodies to an extract from rubber tree (Hevea brasiliensis latex and recombinant pollen allergens (Phl P 1, Phl P 2, Phl P 5, Bet v 1 and Bet v 2 in the sera of Italian atopic patients

    Directory of Open Access Journals (Sweden)

    Renato E. Rossi

    2001-01-01

    Conclusions: The findings of the present study may support the concept that a high proportion of sera containing IgE to rBet v 2, rPhl p 1 and rPhl p 5 simultaneously contain antilatex IgE. Therefore, patients with specific IgE to these recombinant allergens with no history of current latex exposure may need additional evaluation.

  8. Analysis of the role of betL in contributing to the growth and survival of Listeria monocytogenes LO28.

    Science.gov (United States)

    Sleator, R D; Gahan CGM; O'Driscoll, B; Hill, C

    2000-09-25

    Survival of the food-borne pathogen Listeria monocytogenes in environments of elevated osmolarity and reduced temperature is attributed, at least in part, to the accumulation of the trimethylammonium compound glycine betaine. Previously we identified betL, a gene encoding the secondary glycine betaine transporter BetL, which we linked to the salt tolerance of Listeria. In this report, we demonstrate that betL, preceded by a consensus sigmaB-dependent promoter, is regulated by osmotic up-shock, at least in part at the level of transcription. Using allelic exchange mutagenesis we constructed an in-frame deletion in betL, and used this mutant to determine the role of BetL in contributing to the growth and survival of L. monocytogenes, both in a high risk food (Camembert cheese) and animal model. Our results indicate that while BetL plays an important role in glycine betaine mediated osmoprotection, mutating the gene does not significantly effect either the cryotolerance or virulence of the organism.

  9. High correlation of specific IgE sensitization between birch pollen, soy and apple allergens indicates pollen-food allergy syndrome among birch pollen allergic patients in northern China.

    Science.gov (United States)

    Hao, Guo-Dong; Zheng, Yi-Wu; Wang, Zhi-Xiang; Kong, Xing-Ai; Song, Zhi-Jing; Lai, Xu-Xin; Spangfort, Michael D

    2016-05-01

    Birch pollen sensitization and associated pollen-food syndrome among Chinese allergic patients have not been investigated. Sera from 203 allergic patients from the northern part of China and collected during February to July 2014 were investigated. Specific immunoglobulin E (IgE) against birch pollen extract Bet v and major birch pollen allergen Bet v 1 were measured using the ADVIA Centaur. The presence of major apple allergen Mal d 1 and soy bean allergen Gly m 4 specific IgE was measured by ImmunoCAP 100. Among the 203 sera, 34 sera (16.7%) had specific IgE to Bet v and of these, 28 sera (82.4%) contained Bet v 1-specific IgE. Among the 28 sera with Bet v 1-specific IgE, 27 sera (96.4%) contained Mal d 1-specific IgE and 22 sera (78.6%) contained Gly m 4-specific IgE. Of the 34 Bet v-positive sera, 6 sera (17.6%) contained no specific IgE for Bet v 1, Mal d 1, or Gly m 4. Almost all Bet v-positive sera were donated during the birch pollen season. The prevalence of birch allergy among patients visiting health care during pollen season can be as high as 16.7% in Tangshan City. The majority of Chinese birch allergic patients are IgE-sensitized to the major birch pollen allergen Bet v 1 as well as to the major apple allergen Mal d 1 and soy bean allergen Gly m 4. A relatively high number of patients (17.6%) are IgE-sensitized to birch pollen allergen(s) other than Bet v 1. The high prevalence of specific IgE to Mal d 1 and Gly m 4 among Bet v 1-sensitized patients indicates that pollen-food allergy syndrome could be of clinical relevance in China.

  10. Colonoscopic allergen provocation test with rBet v 1 in patients with pollen-associated food allergy.

    Science.gov (United States)

    Pickert, C N; Lorentz, A; Manns, M P; Bischoff, S C

    2012-10-01

    After consumption of fruits, nuts, and vegetables, several patients with pollen allergy experience gastrointestinal (GI) tract symptoms that are possibly caused by pollen-associated food allergy. The aim of this study was to evaluate the colonoscopic allergen provocation (COLAP) test using the recombinant birch pollen allergen Bet v 1 (rBet v 1) for in vivo diagnosis of pollen-associated food allergy manifesting in the GI tract. Thirty-four patients with a history of adverse reactions to food, GI tract symptoms, and birch pollen pollinosis and five healthy controls underwent COLAP test. Twenty minutes after endoscopic challenge of the cecal mucosa with rBet v 1, the mucosal wheal and flare reaction was registered semiquantitatively, and tissue biopsy specimens were examined for eosinophil mucosal activation. The mucosal reaction to rBet v 1 was correlated with the presence of pollinosis (P = 0.004), history of adverse reaction to Bet v 1-associated food allergens (P = 0.001), and tissue eosinophils' activation (P foods and in four of 18 (22%) patients with a negative history (P food allergy manifesting in the GI tract. © 2012 John Wiley & Sons A/S.

  11. Bromodomain and Extra Terminal (BET Inhibitor Suppresses Macrophage-Driven Steroid-Resistant Exacerbations of Airway Hyper-Responsiveness and Inflammation.

    Directory of Open Access Journals (Sweden)

    Thi Hiep Nguyen

    Full Text Available Exacerbations of asthma are linked to significant decline in lung function and are often poorly controlled by corticosteroid treatment. Clinical investigations indicate that viral and bacterial infections play crucial roles in the onset of steroid-resistant inflammation and airways hyperresponsiveness (AHR that are hallmark features of exacerbations. We have previously shown that interferon γ (IFNγ and lipopolysaccharide (LPS cooperatively activate pulmonary macrophages and induce steroid-resistant airway inflammation and AHR in mouse models. Furthermore, we have established a mouse model of respiratory syncytial virus (RSV-induced exacerbation of asthma, which exhibits macrophage-dependent, steroid-resistant lung disease. Emerging evidence has demonstrated a key role for bromo- and extra-terminal (BET proteins in the regulation of inflammatory gene expression in macrophages. We hypothesised that BET proteins may be involved in the regulation of AHR and airway inflammation in our steroid-resistant exacerbation models.We investigated the effects of a BET inhibitor (I-BET-762 on the development of steroid-resistant AHR and airway inflammation in two mouse models. I-BET-762 administration decreased macrophage and neutrophil infiltration into the airways, and suppressed key inflammatory cytokines in both models. I-BET treatment also suppressed key inflammatory cytokines linked to the development of steroid-resistant inflammation such as monocyte chemoattractant protein 1 (MCP-1, keratinocyte-derived protein chemokine (KC, IFNγ, and interleukin 27 (IL-27. Attenuation of inflammation was associated with suppression of AHR.Our results suggest that BET proteins play an important role in the regulation of steroid-resistant exacerbations of airway inflammation and AHR. BET proteins may be potential targets for the development of future therapies to treat steroid-resistant inflammatory components of asthma.

  12. Bet hedging via seed banking in desert evening primroses (Oenothera, Onagraceae): demographic evidence from natural populations.

    Science.gov (United States)

    Evans, Margaret E K; Ferrière, Régis; Kane, Michael J; Venable, D Lawrence

    2007-02-01

    Bet hedging is one solution to the problem of an unpredictably variable environment: fitness in the average environment is sacrificed in favor of lower variation in fitness if this leads to higher long-run stochastic mean fitness. While bet hedging is an important concept in evolutionary ecology, empirical evidence that it occurs is scant. Here we evaluate whether bet hedging occurs via seed banking in natural populations of two species of desert evening primroses (Oenothera, Onagraceae), one annual and one perennial. Four years of data on plants and 3 years of data on seeds yielded two transitions for the entire life cycle. One year was exceptionally dry, leading to reproductive failure in the sample areas, and the other was above average in precipitation, leading to reproductive success in four of five populations. Stochastic simulations of population growth revealed patterns indicative of bet hedging via seed banking, particularly in the annual populations: variance in fitness and fitness in the average environment were lower with seed banking than without, whereas long-run stochastic mean fitness was higher with seed banking than without across a wide range of probabilities of the wet year. This represents a novel, unusually rigorous demonstration of bet hedging from field data.

  13. Scythopolis -Bet Shean-, city of the decapolis

    Directory of Open Access Journals (Sweden)

    Peter Bugod

    1997-09-01

    Full Text Available The archaeological excavations in the city of Scythopolis (Bet Shean, Israel, capital of the Greek decapolis, have revealed an important urban complex. The architect Bugod has a look over the cityís history, describes the remains that were left intact after the earthquake that destroyed the city in 749 A.D. and poses the philosophical, ethical and technical problems of anastylosis on the different buildings in the field

  14. Afghanistan: Håbet lever – og elektrikerne er tilkaldt

    DEFF Research Database (Denmark)

    Vestenskov, David

    2013-01-01

    bet for den civile afghaner kan til tider virke som et skamskudt fyrtårn, og det bliver næppe genopbygget af kritiske observationer og selvretfærdig debat. Operationens fokus forud for de udenlandske troppers exit er at udvikle sikkerhedsinstitutionerne og skabe arbejdspladser...

  15. EVALUTION OF MONOLAYER MOISTURE CAPACITY AND THE ENERGY CONSTANT OF SOME POEDERED SPICES BY USING BET AND GAB MODELS

    Directory of Open Access Journals (Sweden)

    E.Nurlela2

    2004-08-01

    Full Text Available BET equation (IUPAC standard and GAB equation (European Project Group on physical properties of food recommendation standard for monolayer capacity value evaluations were used for testing the moisture adsorption experimental data of powdered white and black papper, cloves, nutmeg and cinnamon. The BET equation fits only up to aw = 0.44, while the GAB isotherm fits and covers a much wider range (0.06BET, indicating the marked dependency of the BET sorption isotherm curve on the regression range as well as its typical upswing that began at water activity value equals to 0.6. It was also found that the values for water content adsorbed in the monolayer, expressed as the mass of water adsorbed on 100 gram dry-matter of sample, obtained by the GAB equation were higher than those obtained by the BET model but the energy constant value of BET that were higher than the GAB vakue was observed only for black pepper sample.

  16. Surface modification and electrochemical properties of activated carbons for supercapacitor electrodes

    Science.gov (United States)

    Yang, Dan; Qiu, Wenmei; Xu, Jingcai; Han, Yanbing; Jin, Hongxiao; Jin, Dingfeng; Peng, Xiaoling; Hong, Bo; Li, Ji; Ge, Hongliang; Wang, Xinqing

    2015-12-01

    Modifications with different acids (HNO3, H2SO4, HCl and HF, respectively) were introduced to treat the activated carbons (ACs) surface. The microstructures and surface chemical properties were discussed by X-ray diffraction (XRD), thermogravimetric analysis (TGA), ASAP, Raman spectra and Fourier transform infrared (FTIR) spectra. The ACs electrode-based supercapacitors were assembled with 6 mol ṡ L-1 KOH electrolyte. The electrochemical properties were studied by galvanostatic charge-discharge and cyclic voltammetry. The results indicated that although the BET surface area of modified ACs decreased, the functional groups were introduced and the ash contents were reduced on the surface of ACs, receiving larger specific capacitance to initial AC. The specific capacitance of ACs modified with HCl, H2SO4, HF and HNO3 increased by 31.4%, 23%, 21% and 11.6%, respectively.

  17. Two tandem RNase III cleavage sites determine betT mRNA stability in response to osmotic stress in Escherichia coli.

    Directory of Open Access Journals (Sweden)

    Minji Sim

    Full Text Available While identifying genes regulated by ribonuclease III (RNase III in Escherichia coli, we observed that steady-state levels of betT mRNA, which encodes a transporter mediating the influx of choline, are dependent on cellular concentrations of RNase III. In the present study, we also observed that steady-state levels of betT mRNA are dependent on RNase III activity upon exposure to osmotic stress, indicating the presence of cis-acting elements controlled by RNase III in betT mRNA. Primer extension analyses of betT mRNA revealed two tandem RNase III cleavage sites in its stem-loop region, which were biochemically confirmed via in vitro cleavage assays. Analyses of cleavage sites suggested the stochastic selection of cleavage sites by RNase III, and mutational analyses indicated that RNase III cleavage at either site individually is insufficient for efficient betT mRNA degradation. In addition, both the half-life and abundance of betT mRNA were significantly increased in association with decreased RNase III activity under hyper-osmotic stress conditions. Our findings demonstrate that betT mRNA stability is controlled by RNase III at the post-transcriptional level under conditions of osmotic stress.

  18. Nonselective inhibition of the epigenetic transcriptional regulator BET induces marked lymphoid and hematopoietic toxicity in mice

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong U., E-mail: lee.dong@gene.com [Department of Safety Assessment, Genentech, Inc., South San Francisco, CA 94080 (United States); Katavolos, Paula; Palanisamy, Gopinath [Department of Safety Assessment, Genentech, Inc., South San Francisco, CA 94080 (United States); Katewa, Arna [Department of Research Immunology, Genentech, Inc., South San Francisco, CA 94080 (United States); Sioson, Charly; Corpuz, Janice [Department of Safety Assessment, Genentech, Inc., South San Francisco, CA 94080 (United States); Pang, Jodie; DeMent, Kevin; Choo, Edna [Drug Metabolism and Pharmacokinetics, Genentech, Inc., South San Francisco, CA 94080 (United States); Ghilardi, Nico [Department of Research Immunology, Genentech, Inc., South San Francisco, CA 94080 (United States); Diaz, Dolores; Danilenko, Dimitry M. [Department of Safety Assessment, Genentech, Inc., South San Francisco, CA 94080 (United States)

    2016-06-01

    Bromo and extra terminal (BET) proteins (BRD2, BRD3, BRD4 and BRDT) are epigenetic transcriptional regulators required for efficient expression of growth promoting, cell cycle progression and antiapoptotic genes. Through their bromodomain, these proteins bind to acetylated lysine residues of histones and are recruited to transcriptionally active chromatin. Inhibition of the BET-histone interaction provides a tractable therapeutic strategy to treat diseases that may have epigenetic dysregulation. JQ1 is a small molecule that blocks BET interaction with histones. It has been shown to decrease proliferation of patient-derived multiple myeloma in vitro and to decrease tumor burden in vivo in xenograft mouse models. While targeting BET appears to be a viable and efficacious approach, the nonclinical safety profile of BET inhibition remains to be well-defined. We report that mice dosed with JQ1 at efficacious exposures demonstrate dose-dependent decreases in their lymphoid and immune cell compartments. At higher doses, JQ1 was not tolerated and due to induction of significant body weight loss led to early euthanasia. Flow cytometry analysis of lymphoid tissues showed a decrease in both B- and T-lymphocytes with a concomitant decrease in peripheral white blood cells that was confirmed by hematology. Further investigation with the inactive enantiomer of JQ1 showed that these in vivo effects were on-target mediated and not elicited through secondary pharmacology due to chemical structure.

  19. Nonselective inhibition of the epigenetic transcriptional regulator BET induces marked lymphoid and hematopoietic toxicity in mice

    International Nuclear Information System (INIS)

    Lee, Dong U.; Katavolos, Paula; Palanisamy, Gopinath; Katewa, Arna; Sioson, Charly; Corpuz, Janice; Pang, Jodie; DeMent, Kevin; Choo, Edna; Ghilardi, Nico; Diaz, Dolores; Danilenko, Dimitry M.

    2016-01-01

    Bromo and extra terminal (BET) proteins (BRD2, BRD3, BRD4 and BRDT) are epigenetic transcriptional regulators required for efficient expression of growth promoting, cell cycle progression and antiapoptotic genes. Through their bromodomain, these proteins bind to acetylated lysine residues of histones and are recruited to transcriptionally active chromatin. Inhibition of the BET-histone interaction provides a tractable therapeutic strategy to treat diseases that may have epigenetic dysregulation. JQ1 is a small molecule that blocks BET interaction with histones. It has been shown to decrease proliferation of patient-derived multiple myeloma in vitro and to decrease tumor burden in vivo in xenograft mouse models. While targeting BET appears to be a viable and efficacious approach, the nonclinical safety profile of BET inhibition remains to be well-defined. We report that mice dosed with JQ1 at efficacious exposures demonstrate dose-dependent decreases in their lymphoid and immune cell compartments. At higher doses, JQ1 was not tolerated and due to induction of significant body weight loss led to early euthanasia. Flow cytometry analysis of lymphoid tissues showed a decrease in both B- and T-lymphocytes with a concomitant decrease in peripheral white blood cells that was confirmed by hematology. Further investigation with the inactive enantiomer of JQ1 showed that these in vivo effects were on-target mediated and not elicited through secondary pharmacology due to chemical structure.

  20. Construct Validity of Measures of Becker's Side Bet Theory.

    Science.gov (United States)

    Shore, Lynn M.; Tetrick, Lois E.; Shore, Ted H.; Barksdale, Kevin

    2000-01-01

    Becker's side bet theory (remaining in a job because of perceived costs of leaving) was tested using data from 327 working business students. Three factors were most consistent with the theory: bureaucratic organization, nonwork-related concerns, and adjustment to social position. Attachment to the organization was significantly linked to tangible…

  1. 15 CFR 0.735-17 - Gambling, betting, and lotteries.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Gambling, betting, and lotteries. 0.735-17 Section 0.735-17 Commerce and Foreign Trade Office of the Secretary of Commerce EMPLOYEE... organizational support or for benefit or welfare funds for their own members) and similar agency-approved...

  2. Dry etching of ferroelectric Bi4-xEuxTi3O12 (BET) thin films

    International Nuclear Information System (INIS)

    Lim, Kyu-Tae; Kim, Kyoung-Tae; Kim, Dong-Pyo; Kim, Chang-Il

    2004-01-01

    Bi 4-x Eu x Ti 3 O 12 (BET) thin films were etched by using a inductively coupled Cl 2 /Ar plasma. We obtained a maximum etch rate of 69 nm/min at a gas mixing ratio of Cl 2 (20 %)/Ar (80 %). This result suggests that an effective method for BET etching is chemically assisted physical etching. With increasing coil RF power, the plasma density increases so that the increased reactive free radicals and ions enhance the etch rates of BET, Pt, and SiO 2 . As the dc-bias voltage is increased, the increased ion energy leads to an increased etch rate of BET films. From X-ray photoelectron spectroscopy, the intensities of the Bi-O, the Eu-O, and the Ti-O peaks change with increasing Cl 2 concentration. For a pure Ar plasma, the peak associated with the oxygen-metal (O-M: TiO 2 , Bi 2 O 3 , Eu 2 O 3 ) bond seems to disappear while the pure oxygen peak does not appear. After the BET thin films is etched by using a Cl 2 /Ar plasma, the peak associated with the O-M bond increases slowly, but more quickly than the peak associated with pure oxygen atoms, due to a decrease in the Ar-ion bombardment. These results seem to indicate that Bi and Eu react little with Cl atoms and are removed predominantly by argon-ion bombardment. Also, Ti reacts little with Cl radicals and is mainly removed by chemically assisted physical etching.

  3. Control of NF-kB activity in human melanoma by bromodomain and extra-terminal protein inhibitor I-BET151.

    Science.gov (United States)

    Gallagher, Stuart J; Mijatov, Branka; Gunatilake, Dilini; Gowrishankar, Kavitha; Tiffen, Jessamy; James, Wilmott; Jin, Lei; Pupo, Gulietta; Cullinane, Carleen; McArthur, Grant A; Tummino, Peter J; Rizos, Helen; Hersey, Peter

    2014-11-01

    The transcription factor NF-kappaB (NF-kB) is a key regulator of cytokine and chemokine production in melanoma and is responsible for symptoms such as anorexia, fatigue, and weight loss. In addition, NF-kB is believed to contribute to progression of the disease by upregulation of cell cycle and anti-apoptotic genes and to contribute to resistance against targeted therapies and immunotherapy. In this study, we have examined the ability of the bromodomain and extra-terminal (BET) protein inhibitor I-BET151 to inhibit NF-kB in melanoma cells. We show that I-BET151 is a potent, selective inhibitor of a number of NF-kB target genes involved in induction of inflammation and cell cycle regulation and downregulates production of cytokines such as IL-6 and IL-8. SiRNA studies indicate that BRD2 is the main BET protein involved in regulation of NF-kB and that I-BET151 caused transcriptional downregulation of the NF-kB subunit p105/p50. These results suggest that BET inhibitors may have an important role in treatment of melanoma where activation of NF-kB may have a key pathogenic role. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  4. Tailoring surface properties and structure of layered double hydroxides using silanes with different number of functional groups

    International Nuclear Information System (INIS)

    Tao, Qi; He, Hongping; Li, Tian; Frost, Ray L.; Zhang, Dan; He, Zisen

    2014-01-01

    Four silanes, trimethylchlorosilane (TMCS), dimethyldiethoxylsilane (DMDES), 3-aminopropyltriethoxysilane (APTES) and tetraethoxysilane (TEOS), were adopted to graft layered double hydroxides (LDH) via an induced hydrolysis silylation method (IHS). Fourier transform infrared spectra (FTIR) and 29 Si MAS nuclear magnetic resonance spectra ( 29 Si MAS NMR) indicated that APTES and TEOS can be grafted onto LDH surfaces via condensation with hydroxyl groups of LDH, while TMCS and DMDES could only be adsorbed on the LDH surface with a small quantity. A combination of X-ray diffraction patterns (XRD) and 29 Si MAS NMR spectra showed that silanes were exclusively present in the external surface and had little influence on the long range order of LDH. The surfactant intercalation experiment indicated that the adsorbed and/or grafted silane could not fix the interlamellar spacing of the LDH. However, they will form crosslink between the particles and affect the further surfactant intercalation in the silylated samples. The replacement of water by ethanol in the tactoids and/or aggregations and the polysiloxane oligomers formed during silylation procedure can dramatically increase the value of BET surface area (S BET ) and total pore volumes (V p ) of the products. - Graphical abstract: The replacement of water by ethanol in the tactoids and aggregations of LDHs, and the polysiloxane oligomers formed during silylation process can dramatically increase the BET surface area (S BET ) and the total pore volume (V p ) of the silylated products. - Highlights: • Silanes with multifunctional groups were grafted onto LDH surface in C 2 H 5 OH medium. • The number of hydrolysable groups in silanes affects the structure of grafted LDH. • Replacement of H 2 O by C 2 H 5 OH in aggregations increases S BET and V p of grafted LDH. • Polysiloxane oligomers contribute to the increase of S BET and V p of grafted LDH

  5. Effects of engineered nano-titanium dioxide on pore surface properties and phosphorus adsorption of sediment: Its environmental implications

    International Nuclear Information System (INIS)

    Luo, Zhuanxi; Wang, Zhenhong; Wei, QunShan; Yan, Changzhou; Liu, Feng

    2011-01-01

    Highlights: → The attachment of Enano-TiO 2 to surface enhanced markedly sediment BET surface area and t-Plot external surface area. → The fill of Enano-TiO 2 into the micropores reduced significantly the sediment t-Plot micropore surface area. → Enano-TiO 2 could increase sediment phosphorus (P) adsorption maximum and decrease in sediment P binding energy. → P would be easily released because of the decreasing P binding energy of the sediment with elevated Enano-TiO 2 . - Abstract: Understanding the environmental safety and human health implications of engineered nanoparticles (ENPs) is of worldwide importance. As an important ENPs, engineered nano-TiO 2 (Enano-TiO 2 ) may have been substantially deposited in aquatic sediments because of its widely uses. Sediment pore surface properties would be thus significantly influenced due to the large surface area of Enano-TiO 2 . In this study, Enano-TiO 2 was found to greatly impact on sediment pore surface properties. The attachment of Enano-TiO 2 particles to sediment surfaces enhanced markedly BET specific surface area and t-Plot external specific surface area, and thereby increased sediment phosphorus (P) adsorption maximum (S max ). Contrarily, the fill of Enano-TiO 2 particles into the micropores of sediments could significantly reduce t-Plot micropore specific surface area, and cause slight decrease in sediment P binding energy (K). Clearly, P sorbed in sediment would be easily released because of the decreasing P binding energy of the sediment with elevated Enano-TiO 2 . Enano-TiO 2 would thus cause aggravated endogenous pollution in water if such sediment was re-suspended on disturbance. The results obtained in this study contribute to our increasing knowledge of how to regulate physicochemical behavior of pollutants in sediments under the influences of Enano-TiO 2 and/or similar ENPs.

  6. Application of BET_EF at Mount Etna: a retrospective analysis (years 2001-2005

    Directory of Open Access Journals (Sweden)

    Jacopo Selva

    2011-12-01

    Full Text Available Advances in volcano monitoring and forecasting need a multidisciplinary collaborative framework. In light of this, a Bayesian Event Tree (BET approach was performed by the application of the BET for Eruption Forecasting (BET_EF code to analyze the space-time distribution of the volcanic activity of Mount Etna from 2001-2005. First, a reliable monitoring dataset was set up after some sessions to elicit geophysical, volcanological and geochemical ‘precursor’ parameters. A constant unrest probability of 100%, with a magma involvement usually greater than 95%, was computed throughout the time period analyzed. Eruption probabilities higher than 90% were estimated a few days before the onsets of the 2001 and 2002-2003 flank eruptions. Values slightly higher than 75% were observed during the lava fountaining period in June-July 2001. However, the probabilities flattened to around 30% for the 2004-2005 flank eruption. With suitable data, a good depiction of the actual location of the eruptive scenario for the 2001 and 2002-2003 events was provided. Conversely, the size of the eruptions was not indicated.

  7. Role of T-bet, the master regulator of Th1 cells, in the cytotoxicity of murine CD4+ T cells.

    Science.gov (United States)

    Eshima, Koji; Misawa, Kana; Ohashi, Chihiro; Iwabuchi, Kazuya

    2018-05-01

    Although CD4 + T cells are generally regarded as helper T cells, some activated CD4 + T cells have cytotoxic properties. Given that CD4 + cytotoxic T lymphocytes (CTLs) often secrete IFN-γ, CTL activity among CD4 + T cells may be attributable to Th1 cells, where a T-box family molecule, T-bet serves as the "master regulator". However, although the essential contribution of T-bet to expression of IFN-γ has been well-documented, it remains unclear whether T-bet is involved in CD4 + T cell-mediated cytotoxicity. In this study, to investigate the ability of T-bet to confer cytolytic activity on CD4 + T cells, the T-bet gene (Tbx21) was introduced into non-cytocidal CD4 + T cell lines and their cytolytic function analyzed. Up-regulation of FasL (CD178), which provided the transfectant with cytotoxicity, was observed in Tbx21transfected CD4 + T cells but not in untransfected parental cells. In one cell line, T-bet transduction also induced perforin gene (Prf1) expression and Tbx21 transfectants efficiently killed Fas - target cells. Although T-bet was found to repress up-regulation of CD40L (CD154), which controls FasL-mediated cytolysis, the extent of CD40L up-regulation on in vitro-differentiated Th1 cells was similar to that on Th2 cells, suggesting the existence of a compensatory mechanism. These results collectively indicate that T-bet may be involved in the expression of genes, such as FasL and Prf1, which confer cytotoxicity on Th1 cells. © 2018 The Societies and John Wiley & Sons Australia, Ltd.

  8. c-Myb Regulates the T-Bet-Dependent Differentiation Program in B Cells to Coordinate Antibody Responses

    Directory of Open Access Journals (Sweden)

    Dana Piovesan

    2017-04-01

    Full Text Available Summary: Humoral immune responses are tailored to the invading pathogen through regulation of key transcription factors and their networks. This is critical to establishing effective antibody-mediated responses, yet it is unknown how B cells integrate pathogen-induced signals to drive or suppress transcriptional programs specialized for each class of pathogen. Here, we detail the key role of the transcription factor c-Myb in regulating the T-bet-mediated anti-viral program. Deletion of c-Myb in mature B cells significantly increased serum IgG2c and CXCR3 expression by upregulating T-bet, normally suppressed during Th2-cell-mediated responses. Enhanced expression of T-bet resulted in aberrant plasma cell differentiation within the germinal center, mediated by CXCR3 expression. These findings identify a dual role for c-Myb in limiting inappropriate effector responses while coordinating plasma cell differentiation with germinal center egress. Identifying such intrinsic regulators of specialized antibody responses can assist in vaccine design and therapeutic intervention in B-cell-mediated immune disorders. : Piovesan et al. examine how B cells establish transcriptional programs that result in tailored responses to invading pathogens. The authors find that the transcription factor c-Myb represses the T-bet-mediated anti-viral program in B cells. c-Myb limits inappropriate effector responses while coordinating plasma cell differentiation with germinal center egress. Keywords: B cells, c-Myb, T-bet, immunoglobulin, CXCR3, plasma cell, germinal center

  9. On Loss Aversion, Level-1 Reasoning, and Betting

    OpenAIRE

    Ido Erev; Sharon Gilat-Yihyie; Davide Marchiori; Doron Sonsino

    2013-01-01

    Previous research suggests that human reaction to risky opportunities reflects two contradicting biases: Òloss aversion", and Òlimited level of reasoning" that leads to overconfidence. Rejection of attractive gambles is explained by loss aversion, while counterproductive risk seeking is attributed to limited level of reasoning. The current research highlights a shortcoming of this popular (but often implicit) "contradicting biases" assertion. Studies of "negative-sum betting games" reveal hig...

  10. Uptake of acetone, ethanol and benzene to snow and ice: effects of surface area and temperature

    International Nuclear Information System (INIS)

    Abbatt, J P D; Bartels-Rausch, T; Ullerstam, M; Ye, T J

    2008-01-01

    The interactions of gas-phase acetone, ethanol and benzene with smooth ice films and artificial snow have been studied. In one technique, the snow is packed into a cylindrical column and inserted into a low-pressure flow reactor coupled to a chemical-ionization mass spectrometer for gas-phase analysis. At 214 and 228 K, it is found for acetone and ethanol that the adsorbed amounts per surface area match those for adsorption to thin films of ice formed by freezing liquid water, when the specific surface area of the snow (as determined from Kr adsorption at 77 K) and the geometric surface area of the ice films are used. This indicates that freezing thin films of water leads to surfaces that are smooth at the molecular level. Experiments performed to test the effect of film growth on ethanol uptake indicate that uptake is independent of ice growth rate, up to 2.4 μm min -1 . In addition, traditional Brunauer-Emmett-Teller (BET) experiments were performed with these gases on artificial snow from 238 to 266.5 K. A transition from a BET type I isotherm indicative of monolayer formation to a BET type II isotherm indicative of multilayer uptake is observed for acetone at T≥263 K and ethanol at T≥255 K, arising from solution formation on the ice. When multilayer formation does not occur, as was the case for benzene at T≤263 K and for acetone at T≤255 K, the saturated surface coverage increased with increasing temperature, consistent with the quasi-liquid layer affecting adsorption prior to full dissolution/multilayer formation.

  11. Diagnóstico das Deteriorações do Betão do Viaduto da Via Rápida

    OpenAIRE

    Andreia Miranda; Madalena Teles

    2009-01-01

    O objectivo do presente trabalho é o de fazer um estudo petrográfico das deteriorações do betão do viaduto da Via Rápida, localizado no porto de Leixões.Após a recolha e análise de toda a informação sobre as características dos materiais usados nos diferentes betões e suas composições e propriedades, foram efectuadas várias visitas ao viaduto, para inspecção visual da estrutura,levantamento fotográfico das anomalias encontradas e extracção de amostras representativas quer do betão aparentemen...

  12. Surface-specific additive manufacturing test artefacts

    Science.gov (United States)

    Townsend, Andrew; Racasan, Radu; Blunt, Liam

    2018-06-01

    Many test artefact designs have been proposed for use with additive manufacturing (AM) systems. These test artefacts have primarily been designed for the evaluation of AM form and dimensional performance. A series of surface-specific measurement test artefacts designed for use in the verification of AM manufacturing processes are proposed here. Surface-specific test artefacts can be made more compact because they do not require the large dimensions needed for accurate dimensional and form measurements. The series of three test artefacts are designed to provide comprehensive information pertaining to the manufactured surface. Measurement possibilities include deviation analysis, surface texture parameter data generation, sub-surface analysis, layer step analysis and build resolution comparison. The test artefacts are designed to provide easy access for measurement using conventional surface measurement techniques, for example, focus variation microscopy, stylus profilometry, confocal microscopy and scanning electron microscopy. Additionally, the test artefacts may be simply visually inspected as a comparative tool, giving a fast indication of process variation between builds. The three test artefacts are small enough to be included in every build and include built-in manufacturing traceability information, making them a convenient physical record of the build.

  13. Influence of surface oxygenated groups on the formation of active Cu species and the catalytic activity of Cu/AC catalyst for the synthesis of dimethyl carbonate

    Science.gov (United States)

    Zhang, Guoqiang; Li, Zhong; Zheng, Huayan; Hao, Zhiqiang; Wang, Xia; Wang, Jiajun

    2016-12-01

    Activated carbon (AC) supported Cu catalysts are employed to study the influence of surface oxygenated groups on the formation of active Cu species and the catalytic activity of Cu/AC catalyst for oxidative carbonylation of methanol to dimethyl carbonate (DMC). The AC supports are thermal treated under different temperatures in order to adjust the levels of surface oxygenated groups. The AC supports are characterized by BET, TPD-MS and XRD, and the Cu/AC catalysts are characterized by BET, XRD, TEM, XPS, AAS, CH3OH-TPD and N2O chemisorption. The results show that as the treatment temperature is below 800 °C, the BET surface area of the corresponding AC supports are nearly unchanged and close to that of the original AC (1529.6 m2/g). But as the thermal treatment temperature is elevated from 1000 to 1600 °C, the BET surface area of AC supports gradually decreases from 1407.6 to 972.2 m2/g. After loading of Cu, the BET surface area of copper catalysts is in the range of 834.4 to 1545.3 m2/g, which is slightly less than that of the respective supports. When AC is thermal treated at 400 and 600 °C, the unstable carboxylic acid and anhydrides groups are selectively removed, which has weakened the mobility and agglomeration of Cu species during the calcination process, and thus improve the Cu species dispersion over AC support. But as the treatment temperature is elevated from 600 °C to 1200 °C, the Cu species dispersion begins to decline suggesting further removal of stable surface oxygenated groups is unfavorable for Cu species dispersion. Moreover, higher thermal treatment temperature (above 1200 °C) promotes the graphitization degree of AC and leds to the decrease of Cu loading on AC support. Meanwhile, the removal of surface oxygenated groups by thermal treatment is conducive to the formation of more π-sites, and thus promote the reduction of Cu2+ to Cu+ and Cu0 as active centers. The specific surface area of (Cu+ + Cu0) is improved by thermal treatment of AC

  14. Plaster: its influence on the behaviour of mould surface in the gluing process

    International Nuclear Information System (INIS)

    Jordao, M.A.P.; Goulart, E.P.; Souza, D.D.D. de; Kiyohara, P.K.

    1989-01-01

    Plaster is an important auxiliary raw material in ceramics, but the industry in Brazil use to give litle importance to its properties. The IPT Ceramic Department initiated studies to upgrade local knowledge on this material. In this paper, the following already studied topics are presented. Characterization of α and β plaster powder, by X-ray diffraction, optical and scanning electron microscopy, specific gravity and surface are (BET). Influence of the plaster/water ratio on the mould characteristics by X-ray diffraction, scanning electron microscopy, porosity and permeability. Behavior of the plaster mould surface against the moulded surface after several aluminum oxide splip castings by scanning electron microscopy [pt

  15. Dye-Sensitized Solar Cells Based on High Surface Area Nanocrystalline Zinc Oxide Spheres

    Directory of Open Access Journals (Sweden)

    Pavuluri Srinivasu

    2011-01-01

    Full Text Available High surface area nanocrystalline zinc oxide material is fabricated using mesoporous nanostructured carbon as a sacrificial template through combustion process. The resulting material is characterized by XRD, N2 adsorption, HR-SEM, and HR-TEM. The nitrogen adsorption measurement indicates that the materials possess BET specific surface area ca. 30 m2/g. Electron microscopy images prove that the zinc oxide spheres possess particle size in the range of 0.12 μm–0.17 μm. The nanocrystalline zinc oxide spheres show 1.0% of energy conversion efficiency for dye-sensitized solar cells.

  16. Tailoring surface properties and structure of layered double hydroxides using silanes with different number of functional groups

    Energy Technology Data Exchange (ETDEWEB)

    Tao, Qi [Key Laboratory of Mineralogy and Metallogeny, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Chemistry Discipline, Faculty of Science and Technology, Queensland University of Technology, Brisbane, Queensland 4001 (Australia); He, Hongping, E-mail: hehp@gig.ac.cn [Key Laboratory of Mineralogy and Metallogeny, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Chemistry Discipline, Faculty of Science and Technology, Queensland University of Technology, Brisbane, Queensland 4001 (Australia); Li, Tian [Key Laboratory of Mineralogy and Metallogeny, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); University of Chinese, Academy of Sciences, Beijing 100039 (China); Frost, Ray L. [Chemistry Discipline, Faculty of Science and Technology, Queensland University of Technology, Brisbane, Queensland 4001 (Australia); Zhang, Dan; He, Zisen [Key Laboratory of Mineralogy and Metallogeny, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); University of Chinese, Academy of Sciences, Beijing 100039 (China)

    2014-05-01

    Four silanes, trimethylchlorosilane (TMCS), dimethyldiethoxylsilane (DMDES), 3-aminopropyltriethoxysilane (APTES) and tetraethoxysilane (TEOS), were adopted to graft layered double hydroxides (LDH) via an induced hydrolysis silylation method (IHS). Fourier transform infrared spectra (FTIR) and {sup 29}Si MAS nuclear magnetic resonance spectra ({sup 29}Si MAS NMR) indicated that APTES and TEOS can be grafted onto LDH surfaces via condensation with hydroxyl groups of LDH, while TMCS and DMDES could only be adsorbed on the LDH surface with a small quantity. A combination of X-ray diffraction patterns (XRD) and {sup 29}Si MAS NMR spectra showed that silanes were exclusively present in the external surface and had little influence on the long range order of LDH. The surfactant intercalation experiment indicated that the adsorbed and/or grafted silane could not fix the interlamellar spacing of the LDH. However, they will form crosslink between the particles and affect the further surfactant intercalation in the silylated samples. The replacement of water by ethanol in the tactoids and/or aggregations and the polysiloxane oligomers formed during silylation procedure can dramatically increase the value of BET surface area (S{sub BET}) and total pore volumes (V{sub p}) of the products. - Graphical abstract: The replacement of water by ethanol in the tactoids and aggregations of LDHs, and the polysiloxane oligomers formed during silylation process can dramatically increase the BET surface area (S{sub BET}) and the total pore volume (V{sub p}) of the silylated products. - Highlights: • Silanes with multifunctional groups were grafted onto LDH surface in C{sub 2}H{sub 5}OH medium. • The number of hydrolysable groups in silanes affects the structure of grafted LDH. • Replacement of H{sub 2}O by C{sub 2}H{sub 5}OH in aggregations increases S{sub BET} and V{sub p} of grafted LDH. • Polysiloxane oligomers contribute to the increase of S{sub BET} and V{sub p} of grafted LDH.

  17. Thermodynamic properties of antiferromagnetic ordered states of π -d interacting systems of κ -(BETS) 2Fe X4(X =Br ,Cl )

    Science.gov (United States)

    Fukuoka, Shuhei; Yamashita, Satoshi; Nakazawa, Yasuhiro; Yamamoto, Takashi; Fujiwara, Hideki; Shirahata, Takashi; Takahashi, Kazuko

    2016-06-01

    The results are presented for systematic heat capacity measurements of π-d interacting systems of κ -(BETS) 2Fe Br4 and κ -(BETS) 2FeC l4 [BETS = bis(ethylenedithio)tetraselenafulvalene] performed under in-plane magnetic fields. We observed sharp thermal anomalies at 2.47 K for κ -(BETS) 2FeB r4 and at 0.47 K for κ -(BETS) 2FeC l4 at 0 T that are associated with antiferromagnetic transitions of the 3 d electrons in the anion layers. From analyses of the magnetic heat capacity data, we indicate that the two compounds show unconventional thermodynamic behaviors inherent in the π-d interacting layered system. In the case of κ -(BETS) 2FeB r4 , a small hump structure was observed in the magnetic heat capacity below the transition temperature when a magnetic field was applied parallel to the a axis. In the case of κ -(BETS) 2FeC l4 , a similar hump structure was observed at 0 T that remained in the data with magnetic fields applied parallel to the a axis. We demonstrate that the temperature dependencies of the magnetic heat capacities scale well by normalizing the temperatures with dominant one-dimensional direct interactions (Jdd/kB) of each compound. The field dependencies of the transition temperatures and the hump structures are elucidated in one simple magnetic field vs temperature (H -T ) phase diagram. These results indicate that the thermodynamic features of both κ-type BETS salts are essentially equivalent, and the observed hump structures are derived from the one-dimensional Jdd interaction characters, which are still influential for magnetic features even in the long-range magnetic ordered states.

  18. The Transcription Factor T-Bet Is Regulated by MicroRNA-155 in Murine Anti-Viral CD8+ T Cells via SHIP-1

    Directory of Open Access Journals (Sweden)

    Jennifer L. Hope

    2017-12-01

    Full Text Available We report here that the expression of the transcription factor T-bet, which is known to be required for effector cytotoxic CD8+ T lymphocytes (CTL generation and effector memory cell formation, is regulated in CTL by microRNA-155 (miR-155. Importantly, we show that the proliferative effect of miR-155 on CD8+ T cells is mediated by T-bet. T-bet levels in CTL were controlled in vivo by miR-155 via SH2 (Src homology 2-containing inositol phosphatase-1 (SHIP-1, a known direct target of miR-155, and SHIP-1 directly downregulated T-bet. Our studies reveal an important and unexpected signaling axis between miR-155, T-bet, and SHIP-1 in in vivo CTL responses and suggest an important signaling module that regulates effector CTL immunity.

  19. A comparative content analysis of media reporting of sports betting in Australia: lessons for public health media advocacy approaches.

    Science.gov (United States)

    David, Jennifer L; Thomas, Samantha L; Randle, Melanie; Bowe, Steven J; Daube, Mike

    2017-11-14

    Harmful gambling is a significant public health issue. There has been widespread discussion in the Australian media about the extent and impact of sports betting on the Australian community, particularly relating to young men and children. Given the role that the media plays in influencing policy change and political agendas, and the acknowledgement that media based advocacy is a fundamental component of successful advocacy campaigns, this research aimed to investigate how different stakeholder groups discuss sports betting within the Australian print media. The study uses this information to provide recommendations to guide public health media advocacy approaches. A quantitative content analysis of print media articles was conducted during two significant Parliamentary Inquiries about sports betting - (1) The Joint Select Committee Inquiry into the Advertising and Promotion of Gambling Services in Sport (2012/2013), and (2) 'The Review of Illegal Offshore Wagering (2015/2016). A total of 241 articles from 12 daily Australian newspapers were analysed. Statistical analysis was used to compare frequency of, and changes in, themes, voices and perspectives over time. Discussions about the marketing and communication of sports betting was a main theme in media reporting (n = 165, 68.5%), while discussions about gambling reform decreased significantly across the two time periods (p sports betting industry (p sporting code (p sports betting is important in developing effective public health advocacy approaches. This study indicates that discussions about the marketing strategies utilised by the sports betting industry was still a main theme in media articles. However, discussions relating to sports betting reforms, in particular to protect individuals who may be vulnerable to the harm associated with these products and their promotional strategies (for example children and young men) decreased during the time periods. Public health advocates may seek to address the

  20. Betting on Illusory Patterns: Probability Matching in Habitual Gamblers.

    Science.gov (United States)

    Gaissmaier, Wolfgang; Wilke, Andreas; Scheibehenne, Benjamin; McCanney, Paige; Barrett, H Clark

    2016-03-01

    Why do people gamble? A large body of research suggests that cognitive distortions play an important role in pathological gambling. Many of these distortions are specific cases of a more general misperception of randomness, specifically of an illusory perception of patterns in random sequences. In this article, we provide further evidence for the assumption that gamblers are particularly prone to perceiving illusory patterns. In particular, we compared habitual gamblers to a matched sample of community members with regard to how much they exhibit the choice anomaly 'probability matching'. Probability matching describes the tendency to match response proportions to outcome probabilities when predicting binary outcomes. It leads to a lower expected accuracy than the maximizing strategy of predicting the most likely event on each trial. Previous research has shown that an illusory perception of patterns in random sequences fuels probability matching. So does impulsivity, which is also reported to be higher in gamblers. We therefore hypothesized that gamblers will exhibit more probability matching than non-gamblers, which was confirmed in a controlled laboratory experiment. Additionally, gamblers scored much lower than community members on the cognitive reflection task, which indicates higher impulsivity. This difference could account for the difference in probability matching between the samples. These results suggest that gamblers are more willing to bet impulsively on perceived illusory patterns.

  1. the french nuclear bet: political history of the main decisions

    International Nuclear Information System (INIS)

    Taccoen, L.

    2003-01-01

    The double french nuclear bet was an ultimate political choice of an old nation which did not wanted to renounce its glamour. but the world had changed. Is it always possible to conceive a national energy policy, knowing that the french military nuclear strategy is opposed to the rules of the next International Penal Court? (A.L.B.)

  2. Mitochondrial protection impairs BET bromodomain inhibitor-mediated cell death and provides rationale for combination therapeutic strategies.

    Science.gov (United States)

    Lasorsa, E; Smonksey, M; Kirk, J S; Rosario, S; Hernandez-Ilizaliturri, F J; Ellis, L

    2015-12-10

    Inhibitors of the bromodomain and extraterminal domain family (BETI) have recently entered phase I clinical trials. In patients with advanced leukemia's, potent antileukemia activity was displayed with minimum dose-limiting toxicity. In preclinical models of hematological malignancies, including aggressive B-cell lymphomas, BETI induced cell-cycle arrest and apoptosis. However, the underlying cell death mechanisms are still not well understood. Dissecting the mechanisms required by BETI to mediate cell death would provide strong direction on how to best utilize BETI to treat patients with aggressive hematological malignancies. Herein, we provide understanding of the molecular mechanisms underlying BETI-mediated cell death using I-BET762. Induction of cell death occurred in primary murine and human B-cell lymphomas through apoptosis. Genetic dissection using Eμ-myc B-cell lymphoma compound mutants demonstrated that I-BET762-induced apoptosis does not require the p53 pathway. Furthermore, deletion of Apaf1, and thus the absence of a functional apoptosome, is associated with a delayed drug response but do not provide long-term resistance. Prolonged treatment of this model in fact fails to suppress the therapeutic efficacy of the drug and is associated with biochemical features of autophagy. However, lack of mitochondrial permeability completely inhibited I-BET762-mediated tumor cell death, indicating mitochondrial damage as key events for its activity. Combination of I-BET762 with BH3-only mimetics ABT-263 or obatoclax, restored sensitivity to I-BET762 lymphoma killing; however, success was determined by expression of Bcl-2 family antiapoptotic proteins. Our study provides critical insight for clinical decisions regarding the appropriate strategy for using BETI as a single agent or in combination to treat patients with aggressive B-cell lymphomas.

  3. BET Bromodomain Inhibitors with One-Step Synthesis Discovered from Virtual Screen.

    Science.gov (United States)

    Ayoub, Alex M; Hawk, Laura M L; Herzig, Ryan J; Jiang, Jiewei; Wisniewski, Andrea J; Gee, Clifford T; Zhao, Peiliang; Zhu, Jin-Yi; Berndt, Norbert; Offei-Addo, Nana K; Scott, Thomas G; Qi, Jun; Bradner, James E; Ward, Timothy R; Schönbrunn, Ernst; Georg, Gunda I; Pomerantz, William C K

    2017-06-22

    Chemical inhibition of epigenetic regulatory proteins BrdT and Brd4 is emerging as a promising therapeutic strategy in contraception, cancer, and heart disease. We report an easily synthesized dihydropyridopyrimidine pan-BET inhibitor scaffold, which was uncovered via a virtual screen followed by testing in a fluorescence anisotropy assay. Dihydropyridopyimidine 3 was subjected to further characterization and is highly selective for the BET family of bromodomains. Structure-activity relationship data and ligand deconstruction highlight the importance of the substitution of the uracil moiety for potency and selectivity. Compound 3 was also cocrystallized with Brd4 for determining the ligand binding pose and rationalizing subsequent structure-activity data. An additional series of dihydropyridopyrimidines was synthesized to exploit the proximity of a channel near the ZA loop of Brd4, leading to compounds with submicromolar affinity and cellular target engagement. Given these findings, novel and easily synthesized inhibitors are being introduced to the growing field of bromodomain inhibitor development.

  4. BET Bromodomain Inhibitors with One-Step Synthesis Discovered from Virtual Screen

    Energy Technology Data Exchange (ETDEWEB)

    Ayoub, Alex M.; Hawk, Laura M.L.; Herzig, Ryan J.; Jiang, Jiewei; Wisniewski, Andrea J.; Gee, Clifford T.; Zhao, Peiliang; Zhu, Jin-Yi; Berndt, Norbert; Offei-Addo, Nana K.; Scott, Thomas G.; Qi, Jun; Bradner, James E.; Ward, Timothy R.; Schönbrunn, Ernst; Georg, Gunda I.; Pomerantz, William C.K. (Moffitt); (UMM); (Harvard-Med)

    2017-06-06

    Chemical inhibition of epigenetic regulatory proteins BrdT and Brd4 is emerging as a promising therapeutic strategy in contraception, cancer, and heart disease. We report an easily synthesized dihydropyridopyrimidine pan-BET inhibitor scaffold, which was uncovered via a virtual screen followed by testing in a fluorescence anisotropy assay. Dihydropyridopyimidine 3 was subjected to further characterization and is highly selective for the BET family of bromodomains. Structure–activity relationship data and ligand deconstruction highlight the importance of the substitution of the uracil moiety for potency and selectivity. Compound 3 was also cocrystallized with Brd4 for determining the ligand binding pose and rationalizing subsequent structure–activity data. An additional series of dihydropyridopyrimidines was synthesized to exploit the proximity of a channel near the ZA loop of Brd4, leading to compounds with submicromolar affinity and cellular target engagement. Given these findings, novel and easily synthesized inhibitors are being introduced to the growing field of bromodomain inhibitor development.

  5. Effects of engineered nano-titanium dioxide on pore surface properties and phosphorus adsorption of sediment: Its environmental implications

    Energy Technology Data Exchange (ETDEWEB)

    Luo, Zhuanxi [Key Laboratory of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Wang, Zhenhong [Key Laboratory of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Zhangzhou Normal University, Department of Chemistry and Environment Sciences, Zhangzhou 363000 (China); Wei, QunShan [Key Laboratory of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Yan, Changzhou, E-mail: czyan@iue.ac.cn [Key Laboratory of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Liu, Feng [Key Laboratory of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China)

    2011-09-15

    Highlights: {yields} The attachment of Enano-TiO{sub 2} to surface enhanced markedly sediment BET surface area and t-Plot external surface area. {yields} The fill of Enano-TiO{sub 2} into the micropores reduced significantly the sediment t-Plot micropore surface area. {yields} Enano-TiO{sub 2} could increase sediment phosphorus (P) adsorption maximum and decrease in sediment P binding energy. {yields} P would be easily released because of the decreasing P binding energy of the sediment with elevated Enano-TiO{sub 2}. - Abstract: Understanding the environmental safety and human health implications of engineered nanoparticles (ENPs) is of worldwide importance. As an important ENPs, engineered nano-TiO{sub 2} (Enano-TiO{sub 2}) may have been substantially deposited in aquatic sediments because of its widely uses. Sediment pore surface properties would be thus significantly influenced due to the large surface area of Enano-TiO{sub 2}. In this study, Enano-TiO{sub 2} was found to greatly impact on sediment pore surface properties. The attachment of Enano-TiO{sub 2} particles to sediment surfaces enhanced markedly BET specific surface area and t-Plot external specific surface area, and thereby increased sediment phosphorus (P) adsorption maximum (S{sub max}). Contrarily, the fill of Enano-TiO{sub 2} particles into the micropores of sediments could significantly reduce t-Plot micropore specific surface area, and cause slight decrease in sediment P binding energy (K). Clearly, P sorbed in sediment would be easily released because of the decreasing P binding energy of the sediment with elevated Enano-TiO{sub 2}. Enano-TiO{sub 2} would thus cause aggravated endogenous pollution in water if such sediment was re-suspended on disturbance. The results obtained in this study contribute to our increasing knowledge of how to regulate physicochemical behavior of pollutants in sediments under the influences of Enano-TiO{sub 2} and/or similar ENPs.

  6. Therapeutic Mechanism of BET Bromodomain Inhibitor in Breast

    Science.gov (United States)

    2015-12-01

    luminal-like do not disappear on acquisition of resistance. 5 Figure 5. BET bromo- domain inhibition gene expression response. Down-, up- and non...e, Gene tracks depicting Bio-JQ1 and BRD4 with or without JQ1 in SUM159 cells at the HIF1A locus. x-axis, chromosome position with gene structures...JQ1, BRD4, and H3K27ac at the BCL-xL (also known as BCL2L1; f) and SOD2 (g) locus. The x-axis shows position along the chromosome with gene

  7. BASALIT trial: double-blind placebo-controlled allergen immunotherapy with rBet v 1-FV in birch-related soya allergy.

    Science.gov (United States)

    Treudler, R; Franke, A; Schmiedeknecht, A; Ballmer-Weber, B; Worm, M; Werfel, T; Jappe, U; Biedermann, T; Schmitt, J; Brehler, R; Kleinheinz, A; Kleine-Tebbe, J; Brüning, H; Ruëff, F; Ring, J; Saloga, J; Schäkel, K; Holzhauser, T; Vieths, S; Simon, J C

    2017-08-01

    Conflicting results exist on the effect of allergen immunotherapy (AIT) on pollen-related food allergy. We aimed to investigate the efficacy of one-year AIT with the folding variant (FV) of recombinant (r) Bet v 1 on birch-related soya allergy. Of 138 subjects with Bet v 1 sensitization, 82 were positive at double-blind placebo-controlled food challenge (DBPCFC) with soya. A total of 56 of 82 were randomized in the ratio of 2:1 (active: placebo). Per-protocol population (PPP) had received ≥150 μg of allergen or placebo preparation. lowest observed adverse effect levels (LOAEL), postinterventional occurrence of objective signs (objS) at any dose level, sIgE/IgG4 against Bet v 1 and Gly m 4. Between-group changes were investigated (ancova, Mann-Whitney U-test, Fisher exact test). Baseline characteristics including LOAELs were comparable in both groups with objS and subjS occurring in 82% and 95% of active (n = 38) vs 78% and 83% of placebo group (n = 18). After AIT, objS occurred in 24% and 47%, respectively. LOAEL group differences showed a beneficial tendency (P = 0.081) for LOAEL objective in PPP (30 active, 15 placebo). sIgG4 raised only in active group (Bet v 1: P = 0.054, Gly m 4: P = 0.037), and no relevant changes occurred for sIgE. Only 56% of the intended sample size was recruited. For the first time, we present data on the effect of rBet v 1-FV on birch-related soya allergy. rBet v 1-FV AIT induced significant immunogenic effects. Clinical assessment showed a tendency in favour of the active group but did not reach statistical significance. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  8. The conserved 12-amino acid stretch in the inter-bromodomain region of BET family proteins functions as a nuclear localization signal.

    Science.gov (United States)

    Fukazawa, Hidesuke; Masumi, Atsuko

    2012-01-01

    The bromodomain and extraterminal (BET) family is a group of chromatin-binding proteins characterized by two bromodomains, an extraterminal (ET) domain, and several other conserved regions of unknown function. In humans, the BET family consists of four members, BRD2, BRD3, BRD4 and BRDT, that all normally localize to the nucleus. We identified a 12-amino acid stretch in the inter-bromodomain region that is perfectly conserved among the BET family members. We deleted these residues and expressed the mutant proteins in HEK293T cells to investigate the function of this motif. We found that the deletion of this motif alters the localization of BET proteins. Mutated BRD3 and BRD4 were excluded from the nucleus, and BRDT was found to be diffused throughout the nucleus and cytoplasm. Although the mutant BRD2 remained predominantly in the nucleus, a punctate distribution was also observed in the cytosol. It has been reported that a conserved motif between the second bromodomain and the ET domain serves as a nuclear localization signal for BRD2. Nevertheless, BET mutants lacking the reported nuclear localization signal motif but retaining the 12-amino acid stretch resided in the nucleus. Furthermore, these mutants were diffused throughout the cytoplasm when the 12 residues were removed. These results indicate that the conserved amino acid stretch in the inter-bromodomain region of the BET family functions as a nuclear localization signal.

  9. The Expression of T Cell FOXP3 and T-Bet Is Upregulated in Severe but Not Euthyroid Hashimoto’s Thyroiditis

    Directory of Open Access Journals (Sweden)

    Stana Tokić

    2016-01-01

    Full Text Available Hashimoto’s thyroiditis (HT is an organ-specific autoimmune disorder characterized by progressive thyroid failure. Th1 and Treg subset of CD4+ cells have been implicated in the pathogenesis; however, less is known about their respective roles across the spectrum of HT clinical presentations. To shed more light on CD4+ subsets role in HT, we investigated the mRNA expression levels of several Th1/Treg-associated transcription factors (T-bet/ETS1, HIF1α/BLIMP1/FOXP3 in peripheral blood T cells of 10 hypothyroid, untreated HT patients, 10 hypothyroid patients undergoing hormone replacement therapy, 12 euthyroid HT subjects, and 11 healthy controls by the qRT-PCR. Compared to euthyroid HT patients and controls, both hypothyroid (2.34-fold difference versus controls, P<0.01 and thyroxine-supplemented patients (2.5-fold, P<0.001 showed an increased FOXP3 mRNA expression in T cells. Similarly, mRNA expression levels of T-bet were upregulated in severely affected but not in euthyroid HT subjects (2.37-fold and 3.2-fold, hypothyroid and thyroxine-supplemented HT patients versus controls, resp., P<0.01. By contrast, no differences in mRNA expression levels of ETS1, BLIMP1, and HIF1α were observed across the study groups. In summary, severe but not euthyroid HT was associated with robust upregulation of T-bet and FOXP3 mRNA in peripheral T cells, independent of the thyroid hormone status but proportional to disease activity.

  10. Characterisation of silica surfaces III: Characterisation of aerosil samples through ethanol adsorption and contact angle studies

    Directory of Open Access Journals (Sweden)

    M.S. Nadiye–Tabbiruka

    2009-12-01

    Full Text Available Aerosil samples, heat treated and then silylated with various silanes at various temperatures have been characterised by adsorption of ethanol at 293 K. Adsorption isotherms were plotted and the BET specific surface areas were determined. Contact angles were measured by the captive bubble method at the three phase contact line in ethanol, on glass slides similarly modified. Silylation was found to alter the ethanol adsorptive properties on aerosil and increase the contact angles on the glass slides to extents that depend on the silane used as well as the concentration of residual silanols and that of surface silyl groups.

  11. Photocatalytic Activity in CH3CN Related to the Surface Properties of TiO2 Powders Prepared by Sol-Gel Method

    OpenAIRE

    Bettoni, Marta; Candori, Pietro; Marmottini, Fabio; Perenze, Nicoletta; Rol, Cesare; Sebastiani, Giovanni V.; Vecchiocattivi, Franco

    2009-01-01

    Some TiO2 powders, prepared from titanium(IV)tetraisopropoxide by the sol-gel method and thermally treated between 100 and 1000∘C, have been characterized by X-ray powder diffraction and by nitrogen adsorption and desorption at 77 K to calculate the BET-specific surface area, from which the micropore volume and the external surface area can be derived. The photocatalytic activity (ka) of the above powders has been evaluated considering the TiO2-sensitized photo-oxidation of 4-methoxybenzyl al...

  12. Responsiveness of the major birch allergen Bet v 1 scaffold to the gastric environment: Impact on structure and allergenic activity

    DEFF Research Database (Denmark)

    Sancho, Ana I; Wangorsch, Andrea; Jensen, Bettina M

    2011-01-01

    Four Bet v 1 homologous food allergens from celeriac (rApi g 1), apple (rMal d 1), peach (rPru p 1) and hazelnut (rCor a 1), were used to probe the structural responsiveness of the Bet v 1 scaffold to gastric digestion conditions and its impact on allergenicity....

  13. Regulation of NO synthesis, local inflammation, and innate immunity to pathogens by BET family proteins.

    Science.gov (United States)

    Wienerroither, Sebastian; Rauch, Isabella; Rosebrock, Felix; Jamieson, Amanda M; Bradner, James; Muhar, Matthias; Zuber, Johannes; Müller, Mathias; Decker, Thomas

    2014-02-01

    Transcriptional activation of the Nos2 gene, encoding inducible nitric oxide synthase (iNOS), during infection or inflammation requires coordinate assembly of an initiation complex by the transcription factors NF-κB and type I interferon-activated ISGF3. Here we show that infection of macrophages with the intracellular bacterial pathogen Listeria monocytogenes caused binding of the BET proteins Brd2, Brd3, and, most prominently, Brd4 to the Nos2 promoter and that a profound reduction of Nos2 expression occurred in the presence of the BET inhibitor JQ1. RNA polymerase activity at the Nos2 gene was regulated through Brd-mediated C-terminal domain (CTD) phosphorylation at serine 5. Underscoring the critical importance of Brd for the regulation of immune responses, application of JQ1 reduced NO production in mice infected with L. monocytogenes, as well as innate resistance to L. monocytogenes and influenza virus. In a murine model of inflammatory disease, JQ1 treatment increased the colitogenic activity of dextran sodium sulfate (DSS). The data presented in our study suggest that BET protein inhibition in a clinical setting poses the risk of altering the innate immune response to infectious or inflammatory challenge.

  14. Specific surface area evaluation method by using scanning electron microscopy

    International Nuclear Information System (INIS)

    Petrescu, Camelia; Petrescu, Cristian; Axinte, Adrian

    2000-01-01

    Ceramics are among the most interesting materials for a large category of applications, including both industry and health. Among the characteristic of the ceramic materials, the specific surface area is often difficult to evaluate.The paper presents a method of evaluation for the specific surface area of two ceramic powders by means of scanning electron microscopy measurements and an original method of computing the specific surface area.Cumulative curves are used to calculate the specific surface area under assumption that the values of particles diameters follow a normal logarithmic distribution. For two powder types, X7R and NPO the results are the following: - for the density ρ (g/cm 2 ), 5.5 and 6.0, respectively; - for the average diameter D bar (μm), 0.51 and 0.53, respectively; - for σ, 1.465 and 1.385, respectively; - for specific surface area (m 2 /g), 1.248 and 1.330, respectively. The obtained results are in good agreement with the values measured by conventional methods. (authors)

  15. Surface area and chemical reactivity characteristics of uranium metal corrosion products

    International Nuclear Information System (INIS)

    Totemeier, T. C.

    1998-01-01

    The results of an initial characterization of hydride-containing corrosion products from uranium metal Zero Power Physics Reactor (ZPPR) fuel plates are presented. Sorption analyses using the BET method with a Kr adsorbate were performed to measure the specific areas of corrosion product samples. The specific surface areas of the corrosion products varied from 0.66 to 1.01 m 2 /g. The reactivity of the products in Ar-9%O 2 and Ar-20%O 2 were measured at temperatures between 35 C and 150 C using a thermo-gravimetric analyzer. Ignition of the products occurred at temperatures of 150 C and above. The oxidation rates below ignition were comparable to rates observed for uranium metal

  16. Specifications for surface reaction analysis apparatus

    International Nuclear Information System (INIS)

    Teraoka, Yuden; Yoshigoe, Akitaka

    2001-03-01

    A surface reaction analysis apparatus was installed at the JAERI soft x-ray beamline in the SPring-8 as an experimental end-station for the study of surface chemistry. The apparatus is devoted to the study concerning the influence of translational kinetic energy of incident molecules to chemical reactions on solid surfaces with gas molecules. In order to achieve the research purpose, reactive molecular scattering experiments and photoemission spectroscopic measurements using synchrotron radiation are performed in that apparatus via a supersonic molecular beam generator, an electron energy analyzer and a quadrupole mass analyzer. The detail specifications for the apparatus are described in this report. (author)

  17. RhIL-11 treatment normalized Th1/Th2 and T-bet/GATA-3 imbalance in in human immune thrombocytopenic purpura (ITP).

    Science.gov (United States)

    Lin, Ying; Zhou, Xieming; Guo, Wenjian; Li, Qianqian; Pan, Xiahui; Bao, Yunhua; He, Muqing; Zhu, Baoling; Lin, Xiaoji; Jin, Limin; Yao, Rongxin

    2016-09-01

    Immune thrombocytopenia (ITP) is an autoimmune hemorrhagic disorder characterized by reduction in platelet counts. T helper 1 (Th1) cells polarization with an increased shift of Th1/Th2 ratio has been reported in ITP. This shift is associated with transcription factor T-box expressed in T cells (T-bet) upregulation and GATA-binding protein 3 (GATA-3) downregulation, leading to an increased T-bet/GATA-3 ratio. Our previous in vitro study showed that recombinant human interleukin-11 (rhIL-11) could normalize Th1/Th2 imbalance in the peripheral blood mononuclear cells (PBMCs) isolated from adult ITP patients, which co-occurred with T-bet/GATA-3 ratio restoration. In this report, we investigated whether rhIL-11 had therapeutic effect in clinical ITP patients and whether rhIL-11 treatment could normalize Th1/Th2 and T-bet/GATA-3 levels in vivo. We found rhIL-11 treatment had a response rate of 67.7% and significantly decreased Th1 and T-bet levels but increased Th2 and GATA-3 levels in ITP patients who showed good response, normalizing Th1/Th2 and T-bet/GATA-3 ratios similar to that in healthy controls. Thus our study suggested rhIL-11 was effective with tolerable adverse effects in ITP. The treatment strategy warrants further clinical investigation. Copyright © 2016 Elsevier B.V. All rights reserved.

  18. Surface area and pore size characteristics of nanoporous gold subjected to thermal, mechanical, or surface modification studied using gas adsorption isotherms, cyclic voltammetry, thermogravimetric analysis, and scanning electron microscopy

    Science.gov (United States)

    Tan, Yih Horng; Davis, Jason A.; Fujikawa, Kohki; Ganesh, N. Vijaya; Demchenko, Alexei V.

    2012-01-01

    Nitrogen adsorption/desorption isotherms are used to investigate the Brunauer, Emmett, and Teller (BET) surface area and Barrett-Joyner-Halenda (BJH) pore size distribution of physically modified, thermally annealed, and octadecanethiol functionalized np-Au monoliths. We present the full adsorption-desorption isotherms for N2 gas on np-Au, and observe type IV isotherms and type H1 hysteresis loops. The evolution of the np-Au under various thermal annealing treatments was examined using scanning electron microscopy (SEM). The images of both the exterior and interior of the thermally annealed np-Au show that the porosity of all free standing np-Au structures decreases as the heat treatment temperature increases. The modification of the np-Au surface with a self-assembled monolayer (SAM) of C18-SH (coverage of 2.94 × 1014 molecules cm−2 based from the decomposition of the C18-SH using thermogravimetric analysis (TGA)), was found to reduce the strength of the interaction of nitrogen gas with the np-Au surface, as reflected by a decrease in the ‘C’ parameter of the BET equation. From cyclic voltammetry studies, we found that the surface area of the np-Au monoliths annealed at elevated temperatures followed the same trend with annealing temperature as found in the BET surface area study and SEM morphology characterization. The study highlights the ability to control free-standing nanoporous gold monoliths with high surface area, and well-defined, tunable pore morphology. PMID:22822294

  19. Comparison of diffusion charging and mobility-based methods for measurement of aerosol agglomerate surface area.

    Science.gov (United States)

    Ku, Bon Ki; Kulkarni, Pramod

    2012-05-01

    We compare different approaches to measure surface area of aerosol agglomerates. The objective was to compare field methods, such as mobility and diffusion charging based approaches, with laboratory approach, such as Brunauer, Emmett, Teller (BET) method used for bulk powder samples. To allow intercomparison of various surface area measurements, we defined 'geometric surface area' of agglomerates (assuming agglomerates are made up of ideal spheres), and compared various surface area measurements to the geometric surface area. Four different approaches for measuring surface area of agglomerate particles in the size range of 60-350 nm were compared using (i) diffusion charging-based sensors from three different manufacturers, (ii) mobility diameter of an agglomerate, (iii) mobility diameter of an agglomerate assuming a linear chain morphology with uniform primary particle size, and (iv) surface area estimation based on tandem mobility-mass measurement and microscopy. Our results indicate that the tandem mobility-mass measurement, which can be applied directly to airborne particles unlike the BET method, agrees well with the BET method. It was also shown that the three diffusion charging-based surface area measurements of silver agglomerates were similar within a factor of 2 and were lower than those obtained from the tandem mobility-mass and microscopy method by a factor of 3-10 in the size range studied. Surface area estimated using the mobility diameter depended on the structure or morphology of the agglomerate with significant underestimation at high fractal dimensions approaching 3.

  20. A comparative content analysis of media reporting of sports betting in Australia: lessons for public health media advocacy approaches

    Directory of Open Access Journals (Sweden)

    Jennifer L. David

    2017-11-01

    Full Text Available Abstract Background Harmful gambling is a significant public health issue. There has been widespread discussion in the Australian media about the extent and impact of sports betting on the Australian community, particularly relating to young men and children. Given the role that the media plays in influencing policy change and political agendas, and the acknowledgement that media based advocacy is a fundamental component of successful advocacy campaigns, this research aimed to investigate how different stakeholder groups discuss sports betting within the Australian print media. The study uses this information to provide recommendations to guide public health media advocacy approaches. Methods A quantitative content analysis of print media articles was conducted during two significant Parliamentary Inquiries about sports betting - (1 The Joint Select Committee Inquiry into the Advertising and Promotion of Gambling Services in Sport (2012/2013, and (2 'The Review of Illegal Offshore Wagering (2015/2016. A total of 241 articles from 12 daily Australian newspapers were analysed. Statistical analysis was used to compare frequency of, and changes in, themes, voices and perspectives over time. Results Discussions about the marketing and communication of sports betting was a main theme in media reporting (n = 165, 68.5%, while discussions about gambling reform decreased significantly across the two time periods (p < 0.0001. The presence of sports betting industry (p < 0.0001, sporting code (p < 0.0001 and public health expert (p = 0.001 voices all increased significantly across the two time periods. There were very few (n = 11, 4.6% voices from those who had experienced gambling harm. Finally, while there were significantly fewer articles taking the perspective that regulation changes were needed to protect vulnerable sub-populations (p < 0.0001, articles that had a neutral perspective about the need for regulation change increased

  1. Infinite-genus surfaces and the universal Grassmannian

    OpenAIRE

    Davis, Simon

    1995-01-01

    Correlation functions can be calculated on Riemann surfaces using the operator formalism. The state in the Hilbert space of the free field theory on the punctured disc, corresponding to the Riemann surface, is constructed at infinite genus, verifying the inclusion of these surfaces in the Grassmannian. In particular, a subset of the class of $O_{HD}$ surfaces can be identified with a subset of the Grassmannian. The concept of flux through the ideal boundary is used to study the connection bet...

  2. Protein imprinting and recognition via forming nanofilms on microbeads surfaces in aqueous media

    International Nuclear Information System (INIS)

    Lu Yan; Yan Changling; Wang Xuejing; Wang Gongke

    2009-01-01

    In this paler, we present a technique of forming nanofilms of poly-3-aminophenylboronic acid (pAPBA) on the surfaces of polystyrene (PS) microbeads for proteins (papain and trypsin) in aqueous. Papain was chosen as a model to study the feasibility of the technique and trypsin as an extension. Obtained core-shell microbeads were characterized using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and BET methods. The results show that pAPBA formed nanofilms (60-100 nm in thickness) on the surfaces of PS microbeads. The specific surface area of the papain-imprinted beads was about 180 m 2 g -1 and its pore size was 31 nm. These imprinted microbeads exhibit high recognition specificity and fast mass transfer kinetics. The specificity of these imprinted beads mainly originates from the spatial effect of imprinted sites. Because the protein-imprinted sites were located at, or close to, the surface, the imprinted beads have good site accessibility toward the template molecules. The facility of the imprinting protocol and the high recognition properties of imprinted microbeads make the approach an attractive solution to problems in the field of biotechnology.

  3. Unusual poly(3-hydroxyalkanoate) (PHA) biosynthesis behavior of Pseudomonas putida Bet001 and Delftia tsuruhatensis Bet002 isolated from palm oil mill effluent.

    Science.gov (United States)

    Razaif-Mazinah, Mohd Rafais Mohd; Anis, Siti Nor Syairah; Harun, Hazwani Izzati; Rashid, Khairunnisa Abdul; Annuar, Mohamad Suffian Mohamad

    2017-03-01

    Pseudomonas putida Bet001 and Delftia tsuruhatensis Bet002, isolated from palm oil mill effluent, accumulated poly(3-hydroxyalkanoates) (PHAs) when grown on aliphatic fatty acids, sugars, and glycerol. The substrates were supplied at 20:1 C/N mole ratio. Among C-even n-alkanoic acids, myristic acid gave the highest PHA content 26 and 28 wt% in P. putida and D. tsuruhatensis, respectively. Among C-odd n-alkanoic acids, undecanoic gave the highest PHA content at 40 wt% in P. putida and 46 wt% in D. tsuruhatensis on pentadecanoic acid. Sugar and glycerol gave <10 wt% of PHA content for both bacteria. Interestingly, D. tsuruhatensis accumulated both short- and medium-chain length PHA when supplied with n-alkanoic acids ranging from octanoic to lauric, sucrose, and glycerol with 3-hydroxybutyrate as the major monomer unit. In P. putida, the major hydroxyalkanoates unit was 3-hydroxyoctanoate and 3-hydroxydecanoate when grown on C-even acids. Conversely, 3-hydroxyheptanoate, 3-hydrxoynonanoate, and 3-hydroxyundecanoate were accumulated with C-odd acids. Weight-averaged molecular weight (M w ) was in the range of 53-81 kDa and 107-415 kDa for P. putida and D. tsuruhatensis, respectively. Calorimetric analyses indicated that both bacteria synthesized semicrystalline polymer with good thermal stability with degradation temperature (T d ) ranging from 178 to 282 °C. © 2016 International Union of Biochemistry and Molecular Biology, Inc.

  4. Novel BET protein proteolysis-targeting chimera exerts superior lethal activity than bromodomain inhibitor (BETi) against post-myeloproliferative neoplasm secondary (s) AML cells.

    Science.gov (United States)

    Saenz, D T; Fiskus, W; Qian, Y; Manshouri, T; Rajapakshe, K; Raina, K; Coleman, K G; Crew, A P; Shen, A; Mill, C P; Sun, B; Qiu, P; Kadia, T M; Pemmaraju, N; DiNardo, C; Kim, M-S; Nowak, A J; Coarfa, C; Crews, C M; Verstovsek, S; Bhalla, K N

    2017-09-01

    The PROTAC (proteolysis-targeting chimera) ARV-825 recruits bromodomain and extraterminal (BET) proteins to the E3 ubiquitin ligase cereblon, leading to degradation of BET proteins, including BRD4. Although the BET-protein inhibitor (BETi) OTX015 caused accumulation of BRD4, treatment with equimolar concentrations of ARV-825 caused sustained and profound depletion (>90%) of BRD4 and induced significantly more apoptosis in cultured and patient-derived (PD) CD34+ post-MPN sAML cells, while relatively sparing the CD34+ normal hematopoietic progenitor cells. RNA-Seq, Reverse Phase Protein Array and mass cytometry 'CyTOF' analyses demonstrated that ARV-825 caused greater perturbations in messenger RNA (mRNA) and protein expressions than OTX015 in sAML cells. Specifically, compared with OTX015, ARV-825 treatment caused more robust and sustained depletion of c-Myc, CDK4/6, JAK2, p-STAT3/5, PIM1 and Bcl-xL, while increasing the levels of p21 and p27. Compared with OTX015, PROTAC ARV-771 treatment caused greater reduction in leukemia burden and further improved survival of NSG mice engrafted with luciferase-expressing HEL92.1.7 cells. Co-treatment with ARV-825 and JAK inhibitor ruxolitinib was synergistically lethal against established and PD CD34+ sAML cells. Notably, ARV-825 induced high levels of apoptosis in the in vitro generated ruxolitinib-persister or ruxolitinib-resistant sAML cells. These findings strongly support the in vivo testing of the BRD4-PROTAC based combinations against post-MPN sAML.

  5. Alkylglycerols modulate the proliferation and differentiation of non-specific agonist and specific antigen-stimulated splenic lymphocytes.

    Directory of Open Access Journals (Sweden)

    Linxi Qian

    Full Text Available Alkylglycerols (AKGs are ether-linked glycerols derived from shark liver oil and found in small amounts in human milk. Previous studies showed that oral AKGs administration significantly increased the immune response in mice. The aim of the present study was to investigate the in vitro immunomodulatory effect of AKGs on stimulating splenic lymphocyte responses. C57BL/6 mice were immunized with hepatitis B surface antigen (HBsAg. Splenic B cells were purified and stimulated with anti-BCR and anti-CD38. Meanwhile, splenic CD4+ T cells were purified and stimulated with anti-CD3 and anti-CD28. For antigen specific stimulation, the purified CD4+ T cells were cocultured with HBsAg -pulsed dendritic cells. The stimulated lymphocytes were treated with different concentrations of AKGs. The cell proliferation was assessed by [3H]-thymidine incorporation assay. The maturation of B cells was assessed by examining the germline (GL transcription of IgG (γ1 mRNA expression, and the surface expressions of CD80/CD86 markers were examined by flow cytometry analysis. Th1/Th2 polarity was assessed by T-BET (Th1/GATA-3 (Th2 flow cytometry assay and by characteristic cytokines ELISA assay (TNF-α and IFN-γ for Th1; IL-4 and IL-10 for Th2. It was found that AKGs significantly increased the BCR/CD38 -stimulated B cell proliferation. The T cell proliferation in response to CD3/CD28 or specific antigen stimulation was also increased by AKGs. The transcriptional level of IgG (γ1 and the expressions of CD80/CD86 molecules were markedly increased by AKGs in BCR/CD38 -stimulated B cells. Meanwhile, the results showed that AKGs increased the expression of T-BET transcriptional factor and the production of Th1 cytokines (TNF-α and IFN-γ upon CD3/CD28 stimulation; whereas, levels of Th2 cytokines (IL-4 and IL-10 were decreased by AKGs. Our study demonstrated that AKGs can modulate immune responses by boosting the proliferation and maturation of murine lymphocytes in vitro.

  6. High surface area niobium oxides as catalysts for improved hydrogen sorption properties of ball milled MgH2

    International Nuclear Information System (INIS)

    Bhat, V.V.; Rougier, A.; Aymard, L.; Nazri, G.A.; Tarascon, J.-M.

    2008-01-01

    We report, high surface area (up to 200 m 2 /g) nanocrystalline niobium oxide (so called p-Nb 2 O 5 ) synthesized by 'chimie douce' route and its importance in enhancing the hydrogen sorption properties of MgH 2 . p-Nb 2 O 5 induces faster kinetics than commonly used commercial Nb 2 O 5 (c-Nb 2 O 5 ) when ball milled with MgH 2 (named (MgH 2 ) catalyst ) by reducing the time of desorption from 35 min in (MgH 2 ) c-Nb 2 O 5 to 12 min in (MgH 2 ) p-Nb 2 O 5 at 300 deg. C. The BET surface area of as-prepared Nb 2 O 5 was tuned by heat treatment and its effect on sorption properties was studied. Among them, both p-Nb 2 O 5 and Nb 2 O 5 :350 (p-Nb 2 O 5 heated to 350 deg. C with a BET specific surface area of 46 m 2 /g) desorb 5 wt.% within 12 min, exhibiting the best catalytic activity. Furthermore, thanks to the addition of high surface area Nb 2 O 5 , the desorption temperature was successfully lowered down to 200 deg. C, with a significant amount of desorbed hydrogen (4.5 wt.%). In contrast, the composite (MgH 2 ) c-Nb 2 O 5 shows no desorption at this 'low' temperature

  7. Surface area and chemical reactivity characteristics of uranium metal corrosion products.

    Energy Technology Data Exchange (ETDEWEB)

    Totemeier, T. C.

    1998-02-17

    The results of an initial characterization of hydride-containing corrosion products from uranium metal Zero Power Physics Reactor (ZPPR) fuel plates are presented. Sorption analyses using the BET method with a Kr adsorbate were performed to measure the specific areas of corrosion product samples. The specific surface areas of the corrosion products varied from 0.66 to 1.01 m{sup 2}/g. The reactivity of the products in Ar-9%O{sub 2} and Ar-20%O{sub 2} were measured at temperatures between 35 C and 150 C using a thermo-gravimetric analyzer. Ignition of the products occurred at temperatures of 150 C and above. The oxidation rates below ignition were comparable to rates observed for uranium metal.

  8. Bet hedging based cooperation can limit kin selection and form a basis for mutualism.

    Science.gov (United States)

    Uitdehaag, Joost C M

    2011-07-07

    Mutualism is a mechanism of cooperation in which partners that differ help each other. As such, mutualism opposes mechanisms of kin selection and tag-based selection (for example the green beard mechanism), which are based on giving exclusive help to partners that are related or carry the same tag. In contrast to kin selection, which is a basis for parochialism and intergroup warfare, mutualism can therefore be regarded as a mechanism that drives peaceful coexistence between different groups and individuals. Here the competition between mutualism and kin (tag) selection is studied. In a model where kin selection and tag-based selection are dominant, mutualism is promoted by introducing environmental fluctuations. These fluctuations cause reduction in reproductive success by the mechanism of variance discount. The best strategy to counter variance discount is to share with agents who experience the most anticorrelated fluctuations, a strategy called bet hedging. In this way, bet hedging stimulates cooperation with the most unrelated partners, which is a basis for mutualism. Analytic results and simulations reveal that, if this effect is large enough, mutualistic strategies can dominate kin selective strategies. In addition, mutants of these mutualistic strategies that experience fluctuations that are more anticorrelated to their partner, can outcompete wild type, which can lead to the evolution of specialization. In this way, the evolutionary success of mutualistic strategies can be explained by bet hedging-based cooperation. Copyright © 2011 Elsevier Ltd. All rights reserved.

  9. On the specific surface area of nanoporous materials

    NARCIS (Netherlands)

    Detsi, E.; De Jong, E.; Zinchenko, A.; Vukovic, Z.; Vukovic, I.; Punzhin, S.; Loos, K.; ten Brinke, G.; De Raedt, H. A.; Onck, P. R.; De Hosson, J. T. M.

    2011-01-01

    A proper quantification of the specific surface area of nanoporous materials is necessary for a better understanding of the properties that are affected by the high surface-area-to-volume ratio of nanoporous metals, nanoporous polymers and nanoporous ceramics. In this paper we derive an analytical

  10. The role of lipids and salts in two-dimensional crystallization of the glycine-betaine transporter BetP from Corynebacterium glutamicum

    DEFF Research Database (Denmark)

    Tsai, Ching-Ju; Ejsing, Christer S.; Shevchenko, Andrej

    2007-01-01

    The osmoregulated and chill-sensitive glycine-betaine transporter (BetP) from Corynebacterium glutamicum was reconstituted into lipids to form two-dimensional (2D) crystals. The sensitivity of BetP partly bases on its interaction with lipids. Here we demonstrate that lipids and salts influence...... crystal morphology and crystallinity of a C-terminally truncated BetP. The salt type and concentration during crystallization determined whether crystals grew in the form of planar-tubes, sheets or vesicles, while the lipid type influenced crystal packing and order. Three different lipid preparations...... for 2D crystallization were compared. Only the use of lipids extracted from C. glutamicum cells led to the formation of large, well-ordered crystalline areas. To understand the lipid-derived influence on crystallinity, lipid extracts from different stages of the crystallization process were analyzed...

  11. Evidence for Indo-Roman trade from Bet Dwarka waters, west coast of India

    Digital Repository Service at National Institute of Oceanography (India)

    Gaur, A.S.; Sundaresh; Tripati, S.

    India had a very active maritime trade contact with the Roman world between the 4th century BC and the 4th century AD. In this context recent finds of stone anchors, potsherds, lead anchors and a lead ingot from 5 to 8 m water-depth near Bet Dwarka...

  12. Information Salience, Investor Sentiment, and Stock Returns : The Case of British Soccer Betting

    NARCIS (Netherlands)

    Palomino, F.A.; Renneboog, L.D.R.; Zhang, C.

    2008-01-01

    Soccer clubs listed on the London Stock Exchange provide a unique way of testing stock price reactions to different types of news. For each firm, two pieces of information are released on a weekly basis: experts' expectations about game outcomes through the betting odds, and the game outcomes

  13. Information salience, investor sentiment and stock returns : The case of British soccer betting

    NARCIS (Netherlands)

    Palomino, F.A.; Renneboog, L.D.R.; Zhang, C.

    2009-01-01

    Soccer clubs listed on the London Stock Exchange provide a unique way of testing stock price reactions to different types of news. For each firm, two pieces of information are released on a weekly basis: experts' expectations about game outcomes through the betting odds, and the game outcomes

  14. Information Salience, Investor Sentiment, and Stock Returns : The Case of British Soccer Betting

    NARCIS (Netherlands)

    Palomino, F.A.; Renneboog, L.D.R.; Zhang, C.

    2008-01-01

    Soccer clubs listed on the London Stock Exchange provide a unique way of testing stock price reactions to different types of news. For each firm, two pieces of information are released on a weekly basis: experts’ expectations about game outcomes through the betting odds, and the game outcomes

  15. Porous silicon structures with high surface area/specific pore size

    Science.gov (United States)

    Northrup, M.A.; Yu, C.M.; Raley, N.F.

    1999-03-16

    Fabrication and use of porous silicon structures to increase surface area of heated reaction chambers, electrophoresis devices, and thermopneumatic sensor-actuators, chemical preconcentrates, and filtering or control flow devices. In particular, such high surface area or specific pore size porous silicon structures will be useful in significantly augmenting the adsorption, vaporization, desorption, condensation and flow of liquids and gases in applications that use such processes on a miniature scale. Examples that will benefit from a high surface area, porous silicon structure include sample preconcentrators that are designed to adsorb and subsequently desorb specific chemical species from a sample background; chemical reaction chambers with enhanced surface reaction rates; and sensor-actuator chamber devices with increased pressure for thermopneumatic actuation of integrated membranes. Examples that benefit from specific pore sized porous silicon are chemical/biological filters and thermally-activated flow devices with active or adjacent surfaces such as electrodes or heaters. 9 figs.

  16. Detection analysis of surface hydroxyl active sites and simulation calculation of the surface dissociation constants of aqueous diatomite suspensions

    Science.gov (United States)

    Ma, Shu-Cui; Wang, Zhi-Gang; Zhang, Ji-Lin; Sun, De-Hui; Liu, Gui-Xia

    2015-02-01

    The surface properties of the diatomite were investigated using nitrogen adsorption/deadsorption isotherms, TG-DSC, FTIR, and XPS, and surface protonation-deprotonation behavior was determined by continuous acid-base potentiometric titration technique. The diatomite sample with porous honeycomb structure has a BET specific surface area of 10.21 m2/g and large numbers of surface hydroxyl functional groups (i.e. tbnd Si-OH, tbnd Fe-OH, and tbnd Al-OH). These surface hydroxyls can be protonated or deprotonated depending on the pH of the suspension. The experimental potentiometric data in two different ionic strength solutions (0.1 and 0.05 mol/L NaCl) were fitted using ProtoFit GUI V2.1 program by applying diffuse double layer model (DLM) with three amphoteric sites and minimizing the sum of squares between a dataset derivative function and a model derivative function. The optimized surface parameters (i.e. surface dissociation constants (log K1, log K2) and surface site concentrations (log C)) of the sample were obtained. Based on the optimized surface parameters, the surface species distribution was calculated using Program-free PHREEQC 3.1.2. Thus, this work reveals considerable new information about surface protonation-deprotonation processes and surface adsorptive behaviors of the diatomite, which helps us to effectively use the cheap and cheerful diatomite clay adsorbent.

  17. Nanocrystalline GaSbO{sub 4} with high surface area prepared via a facile hydrothermal method and its photocatalytic activity study

    Energy Technology Data Exchange (ETDEWEB)

    Fu Yanghe; Xue Hun; Qin Meng; Liu Ping; Fu Xianzhi [Research Institute of Photocatalysis, Fujian Provincial Key Laboratory of Photocatalysis - State Key Laboratory Breeding Base, Fuzhou University, Fuzhou 350002 (China); Li Zhaohui, E-mail: zhaohuili1969@yahoo.com [Research Institute of Photocatalysis, Fujian Provincial Key Laboratory of Photocatalysis - State Key Laboratory Breeding Base, Fuzhou University, Fuzhou 350002 (China)

    2012-05-05

    Graphical abstract: Nanocrystalline GaSbO{sub 4} prepared via a facile hydrothermal method possesses large specific surface area and exhibits photocatalytic activity for the degradations of salicylic acid and acetone. Highlights: Black-Right-Pointing-Pointer Facile hydrothermal method to nanocrystalline GaSbO{sub 4} with large surface area. Black-Right-Pointing-Pointer GaSbO{sub 4} shows photocatalytic activity for the degradations of salicylic acid and acetone. Black-Right-Pointing-Pointer The photocatalytic mechanism of GaSbO{sub 4} was proposed based on the ESR result. - Abstract: Nanocrystalline GaSbO{sub 4} with small particle size and large BET specific area was successfully prepared via a facile hydrothermal method from Sb{sub 2}O{sub 5}. The influence of the reaction pH on the formation of the final product was investigated. The obtained sample was characterized by X-ray diffraction (XRD), N{sub 2}-sorption BET surface area, UV-vis diffuse reflectance spectroscopy (DRS), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM). The photocatalytic activity for the degradations of salicylic acid and acetone over nanocrystalline GaSbO{sub 4} under UV irradiations was for the first time revealed. Based on the electron spin resonance (ESR) result, the reactive species involved in the photocatalytic reaction over nanocrytalline GaSbO{sub 4} are determined to be HO{center_dot} and O{sub 2}{sup -}{center_dot}. The photocatalytic mechanism of GaSbO{sub 4} was proposed.

  18. Equivalent pore radius and velocity of elastic waves in shale. Skjold Flank-1 Well, Danish North Sea

    DEFF Research Database (Denmark)

    Mbia, Ernest Ncha; Fabricius, Ida Lykke; Oji, Collins O.

    2013-01-01

    and BET specific surface were obtained from these samples using kaolinite and smectite as reference. The cuttings samples were also characterized with respect to mineralogical composition, content of organic carbon and cation exchange capacity.Equivalent pore radius was calculated from porosity and BET...

  19. The multi-dimensional talent support tool (mBET – a systemic approach towards individualized support of the gifted and talented in Austria

    Directory of Open Access Journals (Sweden)

    Johanna Stahl

    2015-03-01

    Full Text Available Providing gifted students with personalized talent development programs is a challenge for teachers and educators alike. The multi-dimensional talent development tool (mBET guides teachers on their way to individualized gifted programs. Within a holistic and systemic concept of giftedness, the mBET brings together the perspectives of teachers, parents and the individual student in assessing talents as well as relevant personality characteristics and environment factors. By facilitating support-oriented round-table talks, the mBET helps teachers, parents and students to develop individually tailored talent development programs, taking into consideration both talents and other factors relevant for successful gifted education (i.e. non-cognitive personality characteristics and environmental factors.

  20. Vaccination for birch pollen allergy. Induction of affinity-matured or blocking IgG antibodies does not account for the reduced binding of IgE to Bet v 1

    DEFF Research Database (Denmark)

    Svenson, Morten; Jacobi, Henrik H; Bødtger, Uffe

    2003-01-01

    -SAV IgG provided similar inhibition of Bet v 1 binding to IgE at equimolar levels, and cross inhibition studies between IgG and IgE showed low inter-individual differences. Following SAV, all sera reduced Bet v 1 binding to CD23(+) cells, correlating with reduced binding of Bet v 1 to IgE (P

  1. Structural and magnetic characterization of the "GASPAR" meteorite from Betéitiva, Boyacá, Colombia

    Science.gov (United States)

    Flor Torres, L. M.; Pérez Alcazar, G. A.

    2014-01-01

    A structural and magnetic characterization has been performed of a plate obtained from the "Gaspar" meteorite from the Otengá region of the Betéitiva municipality, Boyacá, Colombia. The sample was provided by Ingeominas (Colombian Geological Agency). After the studies the sample was classified as an octahedral iron meteorite, due the Fe and Ni concentrations and the Widmanstätten pattern which was observed on the surface of the sample. The plate shows a crack which divides the sample in two regions (side A and B, respectively). Both sides were studied using techniques like X-rays diffraction (XRD), Mössbauer spectrometry, optical microscopy, and scanning electronic microscopy (with EDAX). On both sides an iron Fe-Ni matrix (kamacite) was found; a large quantity of carbon in the form of graphite and in two types: nodular and laminar; and different preferential orientation in both sides of the sample. The studies permit to prove that Gaspar is a fragment of the registered Santa Rosa de Viterbo meteorite.

  2. Stone anchors from Bet Dwarka Island, Gujarat, Coast, India: Significance to historical period maritime activities

    Digital Repository Service at National Institute of Oceanography (India)

    Sundaresh; Gaur, A.S.; Tripati, S.; Gudigar, P.; Bandodkar, S.N.

    Bet Dwarka Island is situated on the extreme west of Indian territory in Jamnagar district of Gujarat. Underwater, the most preserved remains of ancient maritime activity could be the stone anchors of different types, as every boat requires...

  3. BET domain co-regulators in obesity, inflammation and cancer.

    Science.gov (United States)

    Belkina, Anna C; Denis, Gerald V

    2012-06-22

    The bromodomain is a highly conserved motif of 110 amino acids that is bundled into four anti-parallel α-helices and found in proteins that interact with chromatin, such as transcription factors, histone acetylases and nucleosome remodelling complexes. Bromodomain proteins are chromatin 'readers'; they recruit chromatin-regulating enzymes, including 'writers' and 'erasers' of histone modification, to target promoters and to regulate gene expression. Conventional wisdom held that complexes involved in chromatin dynamics are not 'druggable' targets. However, small molecules that inhibit bromodomain and extraterminal (BET) proteins have been described. We examine these developments and discuss the implications for small molecule epigenetic targeting of chromatin networks in cancer.

  4. Crystallization and preliminary X-ray analysis of birch-pollen allergen Bet v 1 in complex with a murine monoclonal IgG Fab' fragment

    DEFF Research Database (Denmark)

    Spangfort, M D; Mirza, Osman Asghar; Gajhede, M

    1999-01-01

    of the clinical symptoms of allergy. In order to study the structural basis of allergen-antibody interaction, a complex between the major birch-pollen allergen Bet v 1 and a Fab' fragment isolated from the murine monoclonal Bet v 1 antibody BV16 has been crystallized. Complex crystals belong to space group P1...

  5. B Cells Negatively Regulate the Establishment of CD49b(+)T-bet(+) Resting Memory T Helper Cells in the Bone Marrow.

    Science.gov (United States)

    Hojyo, Shintaro; Sarkander, Jana; Männe, Christian; Mursell, Mathias; Hanazawa, Asami; Zimmel, David; Zhu, Jinfang; Paul, William E; Fillatreau, Simon; Löhning, Max; Radbruch, Andreas; Tokoyoda, Koji

    2016-01-01

    During an immune reaction, some antigen-experienced CD4 T cells relocate from secondary lymphoid organs (SLOs) to the bone marrow (BM) in a CD49b-dependent manner and reside and rest there as professional memory CD4 T cells. However, it remains unclear how the precursors of BM memory CD4 T cells are generated in the SLOs. While several studies have so far shown that B cell depletion reduces the persistence of memory CD4 T cells in the spleen, we here show that B cell depletion enhances the establishment of memory CD4 T cells in the BM and that B cell transfer conversely suppresses it. Interestingly, the number of antigen-experienced CD4 T cells in the BM synchronizes the number of CD49b(+)T-bet(+) antigen-experienced CD4 T cells in the spleen. CD49b(+)T-bet(+) antigen-experienced CD4 T cells preferentially localize in the red pulp area of the spleen and the BM in a T-bet-independent manner. We suggest that B cells negatively control the generation of CD49b(+)T-bet(+) precursors of resting memory CD4 T cells in the spleen and may play a role in bifurcation of activated effector and resting memory CD4 T cell lineages.

  6. High surface area microporous activated carbons prepared from Fox nut (Euryale ferox) shell by zinc chloride activation

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Arvind; Mohan Jena, Hara, E-mail: hmjena@nitrkl.ac.in

    2015-11-30

    Graphical abstract: - Highlights: • Activated carbons have been prepared from Fox nutshell with chemical activation using ZnCl{sub 2}. • The thermal behavior of the raw material and impregnated raw material has been carried out by thermogravimetric analysis. • The characterizations of the prepared activated carbons have been determined by nitrogen adsorption–desorption isotherms, FTIR, XRD, and FESEM. • The BET surface area and total pore volume of prepared activated carbon has been obtained as 2869 m{sup 2}/g, 2124 m{sup 2}/g, and 1.96 cm{sup 3}/g, respectively. • The microporous surface area, micropore volume, and microporosity percentage of prepared activated carbon has been obtained as 2124 m{sup 2}/g, 1.68 cm{sup 3}/g, and 85.71%, respectively. - Abstract: High surface area microporous activated carbon has been prepared from Fox nutshell (Euryale ferox) by chemical activation with ZnCl{sub 2} as an activator. The process has been conducted at different impregnation (ZnCl{sub 2}/Fox nutshell) ratios (1–2.5) and carbonization temperatures (500–700 °C). The thermal decomposition behavior of Fox nutshell and impregnated Fox nutshell has been carried out by thermogravimetric analysis. The pore properties including the BET surface area, micropore surface area, micropore volume, and pore size distribution of the activated carbons have been determined by nitrogen adsorption–desorption isotherms at −196 °C using the BET, t-plot method, DR, and BJH methods. The BET surface area, the microporous surface area, total pore volume, and micropore volume have been obtained as 2869 m{sup 2}/g, 2124 m{sup 2}/g, 1.96 cm{sup 3}/g, and 1.68 cm{sup 3}/g, respectively, and the microporosity percentage of the prepared activated carbon is 85.71%. The prepared activated carbons have been also characterized with instrumental methods such as Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and field emission scanning electron microscopy (FESEM).

  7. High surface area microporous activated carbons prepared from Fox nut (Euryale ferox) shell by zinc chloride activation

    International Nuclear Information System (INIS)

    Kumar, Arvind; Mohan Jena, Hara

    2015-01-01

    Graphical abstract: - Highlights: • Activated carbons have been prepared from Fox nutshell with chemical activation using ZnCl 2 . • The thermal behavior of the raw material and impregnated raw material has been carried out by thermogravimetric analysis. • The characterizations of the prepared activated carbons have been determined by nitrogen adsorption–desorption isotherms, FTIR, XRD, and FESEM. • The BET surface area and total pore volume of prepared activated carbon has been obtained as 2869 m 2 /g, 2124 m 2 /g, and 1.96 cm 3 /g, respectively. • The microporous surface area, micropore volume, and microporosity percentage of prepared activated carbon has been obtained as 2124 m 2 /g, 1.68 cm 3 /g, and 85.71%, respectively. - Abstract: High surface area microporous activated carbon has been prepared from Fox nutshell (Euryale ferox) by chemical activation with ZnCl 2 as an activator. The process has been conducted at different impregnation (ZnCl 2 /Fox nutshell) ratios (1–2.5) and carbonization temperatures (500–700 °C). The thermal decomposition behavior of Fox nutshell and impregnated Fox nutshell has been carried out by thermogravimetric analysis. The pore properties including the BET surface area, micropore surface area, micropore volume, and pore size distribution of the activated carbons have been determined by nitrogen adsorption–desorption isotherms at −196 °C using the BET, t-plot method, DR, and BJH methods. The BET surface area, the microporous surface area, total pore volume, and micropore volume have been obtained as 2869 m 2 /g, 2124 m 2 /g, 1.96 cm 3 /g, and 1.68 cm 3 /g, respectively, and the microporosity percentage of the prepared activated carbon is 85.71%. The prepared activated carbons have been also characterized with instrumental methods such as Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and field emission scanning electron microscopy (FESEM).

  8. A unified description of adsorption on real surfaces from the Henry Range to the formation of the liquid layer

    Energy Technology Data Exchange (ETDEWEB)

    Cerofolini, G F

    1977-01-01

    A unified description of adsorption on real surfaces from the Henry Range to the formation of the liquid layer was developed on the basis of the BET theory and the assumption that sites on real surfaces are not energetically homogeneous. The model describes the successive Henry, Dubinin-Radushkevich, Freundlich, and multilayer BET behavior of the adsorbed phase as the pressure increases. An analysis of isotherms over the whole coverage range showed that the heterogeneous surface character decreases with increasing number of adsorbed layers; that adsorption into the first and higher layers may be competitive, which produces a new isotherm resembling a mixed type II and III isotherm as proposed by Cerofolini and coworkers.

  9. BET inhibition as a single or combined therapeutic approach in primary paediatric B-precursor acute lymphoblastic leukaemia

    International Nuclear Information System (INIS)

    Da Costa, D; Agathanggelou, A; Perry, T; Weston, V; Petermann, E; Zlatanou, A; Oldreive, C; Wei, W; Stewart, G; Longman, J; Smith, E; Kearns, P; Knapp, S; Stankovic, T

    2013-01-01

    Paediatric B-precursor ALL is a highly curable disease, however, treatment resistance in some patients and the long-term toxic effects of current therapies pose the need for more targeted therapeutic approaches. We addressed the cytotoxic effect of JQ1, a highly selective inhibitor against the transcriptional regulators, bromodomain and extra-terminal (BET) family of proteins, in paediatric ALL. We showed a potent in vitro cytotoxic response of a panel of primary ALL to JQ1, independent of their prognostic features but dependent on high MYC expression and coupled with transcriptional downregulation of multiple pro-survival pathways. In agreement with earlier studies, JQ1 induced cell cycle arrest. Here we show that BET inhibition also reduced c-Myc protein stability and suppressed progression of DNA replication forks in ALL cells. Consistent with c-Myc depletion and downregulation of pro-survival pathways JQ1 sensitised primary ALL samples to the classic ALL therapeutic agent dexamethasone. Finally, we demonstrated that JQ1 reduces ALL growth in ALL xenograft models, both as a single agent and in combination with dexamethasone. We conclude that targeting BET proteins should be considered as a new therapeutic strategy for the treatment of paediatric ALL and particularly those cases that exhibit suboptimal responses to standard treatment

  10. Bet Anywhere, Anytime: An Analysis of Internet Sports Bettors' Responses to Gambling Promotions During Sports Broadcasts by Problem Gambling Severity.

    Science.gov (United States)

    Hing, Nerilee; Russell, Alex Myles Thomas; Lamont, Matthew; Vitartas, Peter

    2017-12-01

    Promotions for online sports betting during televised sports broadcasts are regularly viewed by millions of Australians, raising concerns about their impacts on vulnerable groups including at-risk and problem gamblers. This study examined whether responses to these promotions varied with problem gambling severity amongst 455 Australian Internet sports bettors participating in an online survey. Results indicated that young male Internet sports bettors are especially vulnerable to gambling problems, particularly if they hold positive attitudes to gambling sponsors who embed promotions into sports broadcasts and to the promotional techniques they use and this heightens the risk that alluring messages contribute to excessive gambling. As problem gambling severity increased, so too did recognition that these promotions have impacted negatively on their sports betting behaviour. Because a plethora of sports betting brands and promotions are now heavily integrated into sports coverage, social marketing efforts are needed to offset their persuasive appeal and counter the positive attitudes towards them that appear linked to excessive gambling amongst Internet sports bettors.

  11. [Effect of Acupuncture on the Expression of Transcription Factor T-bet/GATA-3 in Plasma of Rats with Chronic Fatigue Syndrome].

    Science.gov (United States)

    Wang, Xiang-Yi; Liu, Chang-Zheng; Lei, Bo

    2017-06-25

    To observe the effect of acupuncture on the expression of T-box expressed in T cell (T-bet)/GATA binding factor-3 (GATA-3) in plasma of rats with chronic fatigue syndrome (CFS) and explore the mechanism of acupuncture treatment for CFS. Forty-eight healthy male SD rats were randomly divided into blank control group, CFS model group, acupuncture group, and ginsenoside group (12 rats in each group). CFS rat model was established by combining restriction and cold water swimming. Acupuncture was applied to "Baihui"(GV 20), "Guanyuan" (CV 4) and "Zusanli" (ST 36, bilate-ral) acupoints, once a day for two weeks. The ginsenoside group was gavage administrated with ginsenoside, once a day for two weeks. After 14 days, behavioural changes were observed, and the expression levels of T-bet/GATA-3 genes in plasma were detected by RT-PCR. Compared with the blank control group, the time for immobility of forced suspensory test was signi-ficantly longer ( P <0.05) and the time for exhaustive swimming was significantly shortened ( P <0.05) in the CFS model group. Compared with the model group, the two indexes above-mentioned were reversed ( P <0.05) both in the acupuncture group and the ginsenoside group, and the effects in the acupuncture group were more significant than those in the ginsenoside group ( P <0.05). Compared with the blank control group, the expression level of T-cell transcription factor T-bet gene in plasma was higher in the CFS model group ( P <0.05), companied with lower GATA-3 gene expression ( P <0.05). The ratio of T-bet/GATA-3 was higher in the model group than in the blank control group( P <0.05). Compared with the CFS model group, all the indexes above-mentioned were reversed ( P <0.05) in the two treatment groups. Acupuncture group showed a better effect on reducing T-bet gene expression than the ginsenoside group ( P <0.05). Acupuncture can decrease the expression level of T-bet gene while increase the expression of GATA-3 gene, which may be associated

  12. Bet-hedging in bacteriocin producing Escherichia coli populations: the single cell perspective

    Science.gov (United States)

    Bayramoglu, Bihter; Toubiana, David; van Vliet, Simon; Inglis, R. Fredrik; Shnerb, Nadav; Gillor, Osnat

    2017-02-01

    Production of public goods in biological systems is often a collaborative effort that may be detrimental to the producers. It is therefore sustainable only if a small fraction of the population shoulders the cost while the majority reap the benefits. We modelled this scenario using Escherichia coli populations producing colicins, an antibiotic that kills producer cells’ close relatives. Colicin expression is a costly trait, and it has been proposed that only a small fraction of the population actively expresses the antibiotic. Colicinogenic populations were followed at the single-cell level using time-lapse microscopy, and showed two distinct, albeit dynamic, subpopulations: the majority silenced colicin expression, while a small fraction of elongated, slow-growing cells formed colicin-expressing hotspots, placing a significant burden on expressers. Moreover, monitoring lineages of individual colicinogenic cells showed stochastic switching between expressers and non-expressers. Hence, colicin expressers may be engaged in risk-reducing strategies—or bet-hedging—as they balance the cost of colicin production with the need to repel competitors. To test the bet-hedging strategy in colicin-mediated interactions, competitions between colicin-sensitive and producer cells were simulated using a numerical model, demonstrating a finely balanced expression range that is essential to sustaining the colicinogenic population.

  13. New transparent metal-like bilayer composite films with highly conducting layers of {theta}-(BET-TTF){sub 2}Br.3H{sub 2}O nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Mas-Torrent, M.; Laukhina, E.; Rovira, C.; Veciana, J. [Campus Univ. de Bellaterra, Barcelona (Spain). Inst. de Ciencia de Materials; Tkacheva, V. [RAS, Chernogolovka (Russian Federation). Inst. of Problems of Chemical Physics; Zorina, L.; Khasanov, S. [RAS, Chernogolovka (Russian Federation). Inst. of Solid State Physics

    2001-08-01

    A novel conducting bilayer composite (BLC) film-a polycarbonate matrix with a conducting surface layer of a crystalline network of an organic conductor-is presented. A BLC film combines the high stability and physical properties of an organic conductor, in this case the molecular metal {theta}-(BET-TTF){sub 2}Br.3H{sub 2}O, with the flexibility, transparency, and low density of a polymer matrix. The determination of the optimal conditions for the preparation of the new film, which is extremely transparent and has metal-like transport properties down to liquid helium temperature, is described. (orig.)

  14. Experimental Investigation of Coal Dust Wettability Based on Surface Contact Angle

    Directory of Open Access Journals (Sweden)

    Gang Zhou

    2016-01-01

    Full Text Available Wettability is one of the key chemical properties of coal dust, which is very important to dedusting. In this paper, the theory of liquid wetting solid was presented firstly; then, taking the gas coal of Xinglongzhuang coal mine in China as an example, by determination of critical surface tension of coal piece, it can be concluded that only when the surface tension of surfactant solution is less than 45 mN/m can the coal sample be fully wetted. Due to the effect of particle dispersity, compared with the contact angle of milled coal particle, not all the contact angles of screened coal powder with different sizes have a tendency to increase. Furthermore, by the experiments of coal samples’ specific surface areas and porosities, it can be achieved that the volume of single-point total pore decreases with the gradual decreasing of coal’s porosity, while the ultramicropores’ dispersities and multipoint BET specific surface areas increase. Besides, by a series of contact angle experiments with different surfactants, it can be found that with the increasing of porosity and the decreasing of volume percentage of ultramicropore, the contact angle tends to reduce gradually and the coal dust is much easier to get wetted.

  15. A Sure Bet: Business & Education Together. A Handbook for Chamber of Commerce Education Committees.

    Science.gov (United States)

    Abbott, Carol Iddins; Harper, H. James, Ed.

    Project BET (Business and Education Together) was initiated by the California Chamber of Commerce in January 1984 to assist local chambers of commerce in developing long-term school-business partnerships. This handbook, based on work with six pilot chambers of commerce, offers a step-by-step process guide to school-business partnerships, along…

  16. Determining surface areas of marine alga cells by acid-base titration method.

    Science.gov (United States)

    Wang, X; Ma, Y; Su, Y

    1997-09-01

    A new method for determining the surface area of living marine alga cells was described. The method uses acid-base titration to measure the surface acid/base amount on the surface of alga cells and uses the BET (Brunauer, Emmett, and Teller) equation to estimate the maximum surface acid/base amount, assuming that hydrous cell walls have carbohydrates or other structural compounds which can behave like surface Brönsted acid-base sites due to coordination of environmental H2O molecules. The method was applied to 18 diverse alga species (including 7 diatoms, 2 flagellates, 8 green algae and 1 red alga) maintained in seawater cultures. For the species examined, the surface areas of individual cells ranged from 2.8 x 10(-8) m2 for Nannochloropsis oculata to 690 x 10(-8) m2 for Dunaliella viridis, specific surface areas from 1,030 m2.g-1 for Dunaliella salina to 28,900 m2.g-1 for Pyramidomonas sp. Measurement accuracy was 15.2%. Preliminary studies show that the method may be more promising and accurate than light/electron microscopic measurements for coarse estimation of the surface area of living algae.

  17. Osmolality, temperature, and membrane lipid composition modulate the activity of betaine transporter BetP in Corynebacterium glutamicum

    DEFF Research Database (Denmark)

    Ozcan, Nuran; Ejsing, Christer S.; Shevchenko, Andrej

    2007-01-01

    The gram-positive soil bacterium Corynebacterium glutamicum, a major amino acid-producing microorganism in biotechnology, is equipped with several osmoregulated uptake systems for compatible solutes, which is relevant for the physiological response to osmotic stress. The most significant carrier......P activity. We further correlated the change in BetP regulation properties in cells grown at different temperatures to changes in the lipid composition of the plasma membrane. For this purpose, the glycerophospholipidome of C. glutamicum grown at different temperatures was analyzed by mass spectrometry using...... quantitative multiple precursor ion scanning. The molecular composition of glycerophospholipids was strongly affected by the growth temperature. The modulating influence of membrane lipid composition on BetP function was further corroborated by studying the influence of artificial modulation of membrane...

  18. Betænkning om Indsatsen mod ungdomskriminalitet

    DEFF Research Database (Denmark)

    Reimann, Johan; Balvig, Flemming; Bay, Jens

    Kommissionen foretager i betænkningen en samlet gennemgang af indsatsen mod ungdomskriminalitet og præsenterer på grundlag heraf en række forslag til, hvordan indsatsen kan styrkes med henblik på at gøre den så målrettet og virkningsfuld som mulig. Til brug for sine overvejelser har kommissionen...... overvejelser og forslag vedrørende indsatsen mod ungdomskriminalitet omfatter dels den forebyggende indsats, dels reaktionen på kriminalitet, der begås af børn og unge. På baggrund af erfaringerne fra eksisterende tiltag fremhæver kommissionen generelt den tidlige, helhedsorienterede, tværsektorielle og...... sammenhængende kriminalitetsforebyggende indsats som den væsentligste, hvis man for alvor ønsker at sætte effektivt ind for at begrænse ungdomskriminaliteten. Derudover stiller kommissionen en lang række forslag om konkrete tiltag med henblik på at styrke henholdsvis den forebyggende indsats og reaktionen på...

  19. B cells negatively regulate the establishment of CD49b+T-bet+ resting memory T helper cells in the bone marrow

    Directory of Open Access Journals (Sweden)

    Shintaro eHojyo

    2016-02-01

    Full Text Available During an immune reaction, some antigen-experienced CD4 T cells relocate from secondary lymphoid organs (SLOs to the bone marrow (BM in a CD49b-dependent manner and reside and rest there as professional memory CD4 T cells. However, it remains unclear how the precursors of BM memory CD4 T cells are generated in the SLOs. While several studies have so far shown that B cell depletion reduces the persistence of memory CD4 T cells in the spleen, we here show that B cell depletion enhances the establishment of memory CD4 T cells in the BM and that B cell transfer conversely suppresses it. Interestingly, the number of antigen-experienced CD4 T cells in the BM synchronizes the number of CD49b+T-bet+ antigen-experienced CD4 T cells in the spleen. CD49b+T-bet+ antigen-experienced CD4 T cells preferentially localize in the red pulp area of the spleen and the BM in a T-bet-independent manner. We suggest that B cells negatively control the generation of CD49b+T-bet+ precursors of resting memory CD4 T cells in the spleen and may play a role in bifurcation of activated effector and resting memory CD4 T cell lineages.

  20. Analysis of the predictive qualities of betting odds and FIFA World Ranking: evidence from the 2006, 2010 and 2014 Football World Cups.

    Science.gov (United States)

    Wunderlich, Fabian; Memmert, Daniel

    2016-12-01

    The present study aims to investigate the ability of a new framework enabling to derive more detailed model-based predictions from ranking systems. These were compared to predictions from the bet market including data from the World Cups 2006, 2010, and 2014. The results revealed that the FIFA World Ranking has essentially improved its predictive qualities compared to the bet market since the mode of calculation was changed in 2006. While both predictors were useful to obtain accurate predictions in general, the world ranking was able to outperform the bet market significantly for the World Cup 2014 and when the data from the World Cups 2010 and 2014 were pooled. Our new framework can be extended in future research to more detailed prediction tasks (i.e., predicting the final scores of a match or the tournament progress of a team).

  1. Not putting all their eggs in one basket: bet-hedging despite extraordinary annual reproductive output of desert tortoises

    Science.gov (United States)

    Lovich, Jeffrey E.; Ennen, Joshua R.; Yackulic, Charles B.; Meyer-Wilkins, Kathie; Agha, Mickey; Loughran, Caleb L.; Bjurlin, Curtis; Austin, Meaghan; Madrak, Sheila V.

    2015-01-01

    Bet-hedging theory makes the counter-intuitive prediction that, if juvenile survival is low and unpredictable, organisms should consistently reduce short-term reproductive output to minimize the risk of reproductive failure in the long-term. We investigated the long-term reproductive output of an Agassiz's desert tortoise (Gopherus agassizii) population and conformance to a bet-hedging strategy of reproduction in an unpredictable but comparatively productive environment. Most females reproduced every year, even during periods of low precipitation and poor germination of food plants, and the mean percentage of reproducing females did not differ significantly on an annual basis. Although mean annual egg production (clutch size × clutch frequency) differed significantly among years, mean clutch size and mean clutch frequency remained relatively constant. During an El Niño year, mean annual egg production and mean annual clutch frequency were the highest ever reported for this species. Annual egg production was positively influenced by maternal body size but clutch size and clutch frequency were not. Our long-term results confirm earlier conclusions based on short-term research that desert tortoises have a bet-hedging strategy of producing small clutches almost every year. The risk of long-term reproductive failure is minimized in unpredictable environments, both through time by annually producing multiple small clutches over a long reproductive lifespan, even in years of low resource availability, and through space by depositing multiple annual clutches in different locations. The extraordinary annual reproductive output of this population appears to be the result of a typically high but unpredictable biomass of annual food plants at the site relative to tortoise habitat in dryer regions. Under the comparatively productive but unpredictable conditions, tortoises conform to predictions of a bet-hedging strategy of reproduction with relatively small but consistent

  2. Poker, Sports Betting, and Less Popular Alternatives: Status, Friendship Networks, and Male Adolescent Gambling

    Science.gov (United States)

    DiCicco-Bloom, Benjamin; Romer, Daniel

    2012-01-01

    The authors argue that the recent increase in poker play among adolescent males in the United States was primarily attributable to high-status male youth who are more able to organize "informal" gambling games (e.g., poker and sports betting) than are low-status male youth who are left to gamble on "formal" games (e.g., lotteries and slot…

  3. Surface-modified gold nanorods for specific cell targeting

    Science.gov (United States)

    Wang, Chan-Ung; Arai, Yoshie; Kim, Insun; Jang, Wonhee; Lee, Seonghyun; Hafner, Jason H.; Jeoung, Eunhee; Jung, Deokho; Kwon, Youngeun

    2012-05-01

    Gold nanoparticles (GNPs) have unique properties that make them highly attractive materials for developing functional reagents for various biomedical applications including photothermal therapy, targeted drug delivery, and molecular imaging. For in vivo applications, GNPs need to be prepared with very little or negligible cytotoxicitiy. Most GNPs are, however, prepared using growth-directing surfactants such as cetyl trimethylammonium bromide (CTAB), which are known to have considerable cytotoxicity. In this paper, we describe an approach to remove CTAB to a non-toxic concentration. We optimized the conditions for surface modification with methoxypolyethylene glycol thiol (mPEG), which replaced CTAB and formed a protective layer on the surface of gold nanorods (GNRs). The cytotoxicities of pristine and surface-modified GNRs were measured in primary human umbilical vein endothelial cells and human cell lines derived from hepatic carcinoma cells, embryonic kidney cells, and thyroid papillary carcinoma cells. Cytotoxicity assays revealed that treating cells with GNRs did not significantly affect cell viability except for thyroid papillary carcinoma cells. Thyroid cancer cells were more susceptible to residual CTAB, so CTAB had to be further removed by dialysis in order to use GNRs for thyroid cell targeting. PEGylated GNRs are further modified to present monoclonal antibodies that recognize a specific surface marker, Na-I symporter, for thyroid cells. Antibody-conjugated GNRs specifically targeted human thyroid cells in vitro.

  4. Response mechanism for surface acoustic wave gas sensors based on surface-adsorption.

    Science.gov (United States)

    Liu, Jiansheng; Lu, Yanyan

    2014-04-16

    A theoretical model is established to describe the response mechanism of surface acoustic wave (SAW) gas sensors based on physical adsorption on the detector surface. Wohljent's method is utilized to describe the relationship of sensor output (frequency shift of SAW oscillator) and the mass loaded on the detector surface. The Brunauer-Emmett-Teller (BET) formula and its improved form are introduced to depict the adsorption behavior of gas on the detector surface. By combining the two methods, we obtain a theoretical model for the response mechanism of SAW gas sensors. By using a commercial SAW gas chromatography (GC) analyzer, an experiment is performed to measure the frequency shifts caused by different concentration of dimethyl methylphosphonate (DMMP). The parameters in the model are given by fitting the experimental results and the theoretical curve agrees well with the experimental data.

  5. New developments for the site-specific attachment of protein to surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Camarero, J A

    2005-05-12

    Protein immobilization on surfaces is of great importance in numerous applications in biology and biophysics. The key for the success of all these applications relies on the immobilization technique employed to attach the protein to the corresponding surface. Protein immobilization can be based on covalent or noncovalent interaction of the molecule with the surface. Noncovalent interactions include hydrophobic interactions, hydrogen bonding, van der Waals forces, electrostatic forces, or physical adsorption. However, since these interactions are weak, the molecules can get denatured or dislodged, thus causing loss of signal. They also result in random attachment of the protein to the surface. Site-specific covalent attachment of proteins onto surfaces, on the other hand, leads to molecules being arranged in a definite, orderly fashion and uses spacers and linkers to help minimize steric hindrances between the protein surface. This work reviews in detail some of the methods most commonly used as well as the latest developments for the site-specific covalent attachment of protein to solid surfaces.

  6. Regulation of the glucocorticoid receptor via a BET-dependent enhancer drives antiandrogen resistance in prostate cancer.

    Science.gov (United States)

    Shah, Neel; Wang, Ping; Wongvipat, John; Karthaus, Wouter R; Abida, Wassim; Armenia, Joshua; Rockowitz, Shira; Drier, Yotam; Bernstein, Bradley E; Long, Henry W; Freedman, Matthew L; Arora, Vivek K; Zheng, Deyou; Sawyers, Charles L

    2017-09-11

    In prostate cancer, resistance to the antiandrogen enzalutamide (Enz) can occur through bypass of androgen receptor (AR) blockade by the glucocorticoid receptor (GR). In contrast to fixed genomic alterations, here we show that GR-mediated antiandrogen resistance is adaptive and reversible due to regulation of GR expression by a tissue-specific enhancer. GR expression is silenced in prostate cancer by a combination of AR binding and EZH2-mediated repression at the GR locus, but is restored in advanced prostate cancers upon reversion of both repressive signals. Remarkably, BET bromodomain inhibition resensitizes drug-resistant tumors to Enz by selectively impairing the GR signaling axis via this enhancer. In addition to revealing an underlying molecular mechanism of GR-driven drug resistance, these data suggest that inhibitors of broadly active chromatin-readers could have utility in nuanced clinical contexts of acquired drug resistance with a more favorable therapeutic index.

  7. The role of non-genetic inheritance in evolutionary rescue: epigenetic buffering, heritable bet hedging and epigenetic traps.

    Science.gov (United States)

    O'Dea, Rose E; Noble, Daniel W A; Johnson, Sheri L; Hesselson, Daniel; Nakagawa, Shinichi

    2016-01-01

    Rapid environmental change is predicted to compromise population survival, and the resulting strong selective pressure can erode genetic variation, making evolutionary rescue unlikely. Non-genetic inheritance may provide a solution to this problem and help explain the current lack of fit between purely genetic evolutionary models and empirical data. We hypothesize that epigenetic modifications can facilitate evolutionary rescue through 'epigenetic buffering'. By facilitating the inheritance of novel phenotypic variants that are generated by environmental change-a strategy we call 'heritable bet hedging'-epigenetic modifications could maintain and increase the evolutionary potential of a population. This process may facilitate genetic adaptation by preserving existing genetic variation, releasing cryptic genetic variation and/or facilitating mutations in functional loci. Although we show that examples of non-genetic inheritance are often maladaptive in the short term, accounting for phenotypic variance and non-adaptive plasticity may reveal important evolutionary implications over longer time scales. We also discuss the possibility that maladaptive epigenetic responses may be due to 'epigenetic traps', whereby evolutionarily novel factors (e.g. endocrine disruptors) hack into the existing epigenetic machinery. We stress that more ecologically relevant work on transgenerational epigenetic inheritance is required. Researchers conducting studies on transgenerational environmental effects should report measures of phenotypic variance, so that the possibility of both bet hedging and heritable bet hedging can be assessed. Future empirical and theoretical work is required to assess the relative importance of genetic and epigenetic variation, and their interaction, for evolutionary rescue.

  8. Surface and Adsorption Properties of Activated Carbon Fabric Prepared from Cellulosic Polymer: Mixed Activation Method

    Energy Technology Data Exchange (ETDEWEB)

    Bhati, Surendra; Mahur, J. S.; Choubey, O. N. [Barkatullah Univ., Bhopal (India); Dixit, Mahur Savita [Maulana Azad National Institute of Technology, Bhopla (India)

    2013-02-15

    In this study, activated carbon fabric was prepared from a cellulose-based polymer (viscose rayon) via a combination of physical and chemical activation (mixed activation) processes by means of CO{sub 2} as a gasifying agent and surface and adsorption properties were evaluated. Experiments were performed to investigate the consequence of activation temperature (750, 800, 850 and 925 .deg. C), activation time (15, 30, 45 and 60 minutes) and CO{sub 2} flow rate (100, 200, 300 and 400 mL/min) on the surface and adsorption properties of ACF. The nitrogen adsorption isotherm at 77 K was measured and used for the determination of surface area, total pore volume, micropore volume, mesopore volume and pore size distribution using BET, t-plot, DR, BJH and DFT methods, respectively. It was observed that BET surface area and TPV increase with rising activation temperature and time due to the formation of new pores and the alteration of micropores into mesopores. It was also found that activation temperature dominantly affects the surface properties of ACF. The adsorption of iodine and CCl{sub 4} onto ACF was investigated and both were found to correlate with surface area.

  9. Surface and Adsorption Properties of Activated Carbon Fabric Prepared from Cellulosic Polymer: Mixed Activation Method

    International Nuclear Information System (INIS)

    Bhati, Surendra; Mahur, J. S.; Choubey, O. N.; Dixit, Mahur Savita

    2013-01-01

    In this study, activated carbon fabric was prepared from a cellulose-based polymer (viscose rayon) via a combination of physical and chemical activation (mixed activation) processes by means of CO 2 as a gasifying agent and surface and adsorption properties were evaluated. Experiments were performed to investigate the consequence of activation temperature (750, 800, 850 and 925 .deg. C), activation time (15, 30, 45 and 60 minutes) and CO 2 flow rate (100, 200, 300 and 400 mL/min) on the surface and adsorption properties of ACF. The nitrogen adsorption isotherm at 77 K was measured and used for the determination of surface area, total pore volume, micropore volume, mesopore volume and pore size distribution using BET, t-plot, DR, BJH and DFT methods, respectively. It was observed that BET surface area and TPV increase with rising activation temperature and time due to the formation of new pores and the alteration of micropores into mesopores. It was also found that activation temperature dominantly affects the surface properties of ACF. The adsorption of iodine and CCl 4 onto ACF was investigated and both were found to correlate with surface area

  10. Temporal variability and cooperative breeding: testing the bet-hedging hypothesis in the acorn woodpecker.

    Science.gov (United States)

    Koenig, Walter D; Walters, Eric L

    2015-10-07

    Cooperative breeding is generally considered an adaptation to ecological constraints on dispersal and independent breeding, usually due to limited breeding opportunities. Although benefits of cooperative breeding are typically thought of in terms of increased mean reproductive success, it has recently been proposed that this phenomenon may be a bet-hedging strategy that reduces variance in reproductive success (fecundity variance) in populations living in highly variable environments. We tested this hypothesis using long-term data on the polygynandrous acorn woodpecker (Melanerpes formicivorus). In general, fecundity variance decreased with increasing sociality, at least when controlling for annual variation in ecological conditions. Nonetheless, decreased fecundity variance was insufficient to compensate for reduced per capita reproductive success of larger, more social groups, which typically suffered lower estimated mean fitness. We did, however, find evidence that sociality in the form of larger group size resulted in increased fitness in years following a small acorn crop due to reduced fecundity variance. Bet-hedging, although not the factor driving sociality in general, may play a role in driving acorn woodpecker group living when acorns are scarce and ecological conditions are poor. © 2015 The Author(s).

  11. Increased numbers of preexisting memory CD8 T cells and decreased T-bet expression can restrain terminal differentiation of secondary effector and memory CD8 T cells.

    Science.gov (United States)

    Joshi, Nikhil S; Cui, Weiguo; Dominguez, Claudia X; Chen, Jonathan H; Hand, Timothy W; Kaech, Susan M

    2011-10-15

    Memory CD8 T cells acquire effector memory cell properties after reinfection and may reach terminally differentiated, senescent states ("Hayflick limit") after multiple infections. The signals controlling this process are not well understood, but we found that the degree of secondary effector and memory CD8 T cell differentiation was intimately linked to the amount of T-bet expressed upon reactivation and preexisting memory CD8 T cell number (i.e., primary memory CD8 T cell precursor frequency) present during secondary infection. Compared with naive cells, memory CD8 T cells were predisposed toward terminal effector (TE) cell differentiation because they could immediately respond to IL-12 and induce T-bet, even in the absence of Ag. TE cell formation after secondary (2°) or tertiary infections was dependent on increased T-bet expression because T-bet(+/-) cells were resistant to these phenotypic changes. Larger numbers of preexisting memory CD8 T cells limited the duration of 2° infection and the amount of IL-12 produced, and consequently, this reduced T-bet expression and the proportion of 2° TE CD8 T cells that formed. Together, these data show that over repeated infections, memory CD8 T cell quality and proliferative fitness is not strictly determined by the number of serial encounters with Ag or cell divisions, but is a function of the CD8 T cell differentiation state, which is genetically controlled in a T-bet-dependent manner. This differentiation state can be modulated by preexisting memory CD8 T cell number and the intensity of inflammation during reinfection. These results have important implications for vaccinations involving prime-boost strategies.

  12. Pengaruh Kadar Air dan Persamaan Model Bet untuk Prediksi Masa Simpan Kakao (Theobroma cacao L.

    Directory of Open Access Journals (Sweden)

    Rita Hayati

    2017-04-01

    Full Text Available Effect of moisture content and BET equation to the shelf life of cocoa (Theobroma cacao L. has been conducted. Increasing the quality of cocoa beans is with proper post-harvest handling, including how the harvest, the level of ripeness, curing, fermenting, drying up storage. The purpose of this study was to determine the water content and the appropriate levels of critical in determining the shelf life of cocoa. The benefits of this research are as information for farmers in determining the shelf life of cocoa in order to design a storage area corresponding to the respiratory system owned by cocoa. The results showed that the effect of fermentation facilitator (Staphilococcus cerevisiae and drying temperature on water content showed that the fermentation facilitator (Staphilococcus cerevisiae highly significant effect on water content. The drying temperature is also highly significant effect on water content. BET equation obtained was Y = 2,912x + 1.238 (R2 = 0.965, Y = 2,897x + 1.353 (R2 = 0.968 and Y = 2,806x + 1.89 (R2 = 0.954.

  13. PENGARUH STRATEGI PEMBELAJARAN BIOLOGY ENVIRONMENT TECHNOLOGY SOCIETY (BETS TERHADAP KEMAMPUAN BERPIKIR KRITIS DAN HASIL BELAJAR BIOLOGI KELAS X KOTA MALANG

    Directory of Open Access Journals (Sweden)

    Eka Arum Sasi Mahardika

    2016-08-01

    Penelitian ini bertujuan untuk mengetahui pengaruh pembelajaran BETS terhadap kemampuan berpikir kritis dan hasil belajar biologi  kelas X SMA Kota Malang. Penelitian ini dilaksanakan di SMAN 7 Malang pada bulan Februari-Mei 2016. Kemampuan berpikir kritis dan hasil belajar kognitif diukur melalui tes tulis sedangkan ranah afektif dan psikomor diukur melalui observasi selama pembelajaran. Data kemampuan berpikir kritis dan hasil belajar kognitif dianalisis menggunakan uji statistik dengan bantuan Software SPSS 22.0 for Window. Hasil penelitian menunjukkan bahwa ada pengaruh strategi BETS terhadap kemampuan berpikir kritis dan hasil belajar kognitif; afektif kelas eksperimen lebih tinggi dibandingkan kelas kontrol; psikomotor kelas kontrol lebih tinggi dibandingkan kelas kontrol.

  14. Detection analysis of surface hydroxyl active sites and simulation calculation of the surface dissociation constants of aqueous diatomite suspensions

    International Nuclear Information System (INIS)

    Ma, Shu-Cui; Wang, Zhi-Gang; Zhang, Ji-Lin; Sun, De-Hui; Liu, Gui-Xia

    2015-01-01

    Highlights: • To examine surface hydroxyl functional groups of the calcined diatomite by TGA-DSC, FTIR, and XPS. • To calculate the optimized log K 1 , log K 2 and log C values and the surface species distribution of each surface reactive site using ProtoFit and PHREEQC, respectively. - Abstract: The surface properties of the diatomite were investigated using nitrogen adsorption/deadsorption isotherms, TG-DSC, FTIR, and XPS, and surface protonation–deprotonation behavior was determined by continuous acid–base potentiometric titration technique. The diatomite sample with porous honeycomb structure has a BET specific surface area of 10.21 m 2 /g and large numbers of surface hydroxyl functional groups (i.e. ≡Si-OH, ≡Fe-OH, and ≡Al-OH). These surface hydroxyls can be protonated or deprotonated depending on the pH of the suspension. The experimental potentiometric data in two different ionic strength solutions (0.1 and 0.05 mol/L NaCl) were fitted using ProtoFit GUI V2.1 program by applying diffuse double layer model (DLM) with three amphoteric sites and minimizing the sum of squares between a dataset derivative function and a model derivative function. The optimized surface parameters (i.e. surface dissociation constants (log K 1 , log K 2 ) and surface site concentrations (log C)) of the sample were obtained. Based on the optimized surface parameters, the surface species distribution was calculated using Program-free PHREEQC 3.1.2. Thus, this work reveals considerable new information about surface protonation–deprotonation processes and surface adsorptive behaviors of the diatomite, which helps us to effectively use the cheap and cheerful diatomite clay adsorbent

  15. Detection analysis of surface hydroxyl active sites and simulation calculation of the surface dissociation constants of aqueous diatomite suspensions

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Shu-Cui [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Key Laboratory of Applied Chemistry and Nanotechnology at Universities of Jilin Province, Changchun University of Science and Technology, Changchun 130022 (China); Wang, Zhi-Gang [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Zhang, Ji-Lin, E-mail: zjl@ciac.ac.cn [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Sun, De-Hui [Changchun Institute Technology, Changchun 130012 (China); Liu, Gui-Xia, E-mail: liuguixia22@163.com [Key Laboratory of Applied Chemistry and Nanotechnology at Universities of Jilin Province, Changchun University of Science and Technology, Changchun 130022 (China)

    2015-02-01

    Highlights: • To examine surface hydroxyl functional groups of the calcined diatomite by TGA-DSC, FTIR, and XPS. • To calculate the optimized log K{sub 1}, log K{sub 2} and log C values and the surface species distribution of each surface reactive site using ProtoFit and PHREEQC, respectively. - Abstract: The surface properties of the diatomite were investigated using nitrogen adsorption/deadsorption isotherms, TG-DSC, FTIR, and XPS, and surface protonation–deprotonation behavior was determined by continuous acid–base potentiometric titration technique. The diatomite sample with porous honeycomb structure has a BET specific surface area of 10.21 m{sup 2}/g and large numbers of surface hydroxyl functional groups (i.e. ≡Si-OH, ≡Fe-OH, and ≡Al-OH). These surface hydroxyls can be protonated or deprotonated depending on the pH of the suspension. The experimental potentiometric data in two different ionic strength solutions (0.1 and 0.05 mol/L NaCl) were fitted using ProtoFit GUI V2.1 program by applying diffuse double layer model (DLM) with three amphoteric sites and minimizing the sum of squares between a dataset derivative function and a model derivative function. The optimized surface parameters (i.e. surface dissociation constants (log K{sub 1}, log K{sub 2}) and surface site concentrations (log C)) of the sample were obtained. Based on the optimized surface parameters, the surface species distribution was calculated using Program-free PHREEQC 3.1.2. Thus, this work reveals considerable new information about surface protonation–deprotonation processes and surface adsorptive behaviors of the diatomite, which helps us to effectively use the cheap and cheerful diatomite clay adsorbent.

  16. Hierarchical mesosilicalite nanoformulation integrated with cisplatin exhibits target-specific efficient anticancer activity

    Science.gov (United States)

    Jermy, B. Rabindran; Acharya, Sadananda; Ravinayagam, Vijaya; Alghamdi, Hajer Saleh; Akhtar, Sultan; Basuwaidan, Rehab S.

    2018-04-01

    Hierarchically structured zeolitic ZSM-5 and meso MCM-41 interlinked domain had an impeccable use as catalysis in many applications. The aim of the study was to develop a new drug delivery nanoformulation, specifically, cisplatin/mesosilicalite using top-down approach for cancer therapy. Hierarchical mesosilicalite with variable porosity was synthesized using alkaline molar solution (0.2 and 0.7 M NaOH) and was loaded with cisplatin through equilibrium adsorption technique. Physico-chemical properties of the nanoformulation (IAUM-56—Imam Abdulrahman Bin Faisal University Mesosilicalite-56) were characterized using X-ray diffraction, surface area analysis (BET), Fourier transformed infrared spectroscopy (FT-IR), diffuse reflectance UV-Vis spectroscopy, and transmission electron microscopy. Drug release study and anticancer activity were assayed on HeLa and MCF7 cancer cells using MTT assay. X-ray diffraction pattern showed interrelated meso- and microphases, while BET analysis revealed considerable mesoporosity formation with a remodulation of isotherm hysteresis indicating the presence of hierarchical pores. FT-IR showed the presence of nanozeolitic subunits into mesostructure with a band at about 550 cm-1. IAUM-56 demonstrated high cytotoxic activity against HeLa cancer cells with an LC50 of 0.02 mg/ml, MCF7 cancer cells with an LC50 of 0.05 mg/ml, and less toxic to normal fibroblast cells with an LC50 of approximately ten times higher at 0.5 mg/ml. Overall, IAUM-56 showed a high rate of sustained release of cisplatin imparting target specific cytotoxic effect against tumor cells with at least tenfold lower toxicity on normal fibroblast cells. Our nanoformulation has the potential use in cancer therapy as a targeted drug delivery system.

  17. Surface characteristics and antibacterial activity of a silver-doped carbon monolith

    Directory of Open Access Journals (Sweden)

    Marija Vukčević et al

    2008-01-01

    Full Text Available A carbon monolith with a silver coating was prepared and its antimicrobial behaviour in a flow system was examined. The functional groups on the surface of the carbon monolith were determined by temperature-programmed desorption and Boehm's method, and the point of zero charge was determined by mass titration. The specific surface area was examined by N2 adsorption using the Brunauer, Emmett and Teller (BET method. As a test for the surface activity, the deposition of silver from an aqueous solution of a silver salt was used. The morphology and structure of the silver coatings were characterized by scanning electron microscopy and x-ray diffraction. The resistance to the attrition of the silver deposited on the carbon monolith was tested. The antimicrobial activity of the carbon monolith with a silver coating was determined using standard microbiological methods. Carbon monolith samples with a silver coating showed good antimicrobial activity against Escherichia coli, Staphylococcus aureus and Candida albicans, and are therefore suitable for water purification, particularly as personal disposable water filters with a limited capacity.

  18. Study of total oxidation of ethanol using the perovskite-type oxides LaBO{sub 3} (B= Mn, Ni, Fe); Estudo da oxidacao total do etanol usando oxidos tipo perovskita LaBO{sub 3} (B= Mn, Ni, Fe)

    Energy Technology Data Exchange (ETDEWEB)

    Soares, Ana Brigida [Centro Federal de Educacao Tecnologica do Espirito Santo, Vitoria, ES (Brazil). Centro de Ciencias e Tecnologias Quimicas]. E-mail: brigida@cefetes.br; Silva, Paulo Roberto Nagipe da [Universidade Estadual do Norte Fluminense (UENF), Campos dos Goytacases, RJ (Brazil). Centro de Ciencias e Tecnologia; Freitas, Jair C.C. [Universidade Federal do Espirito Santo, Vitoria, ES (Brazil). Centro de Ciencias Exatas. Dept. de Fisica; Almeida, Clara Muniz de [Pontificia Univ. Catolica do Rio de Janeiro, RJ (Brazil). Dept. de Fisica

    2007-09-15

    The present work investigated the effect of coprecipitation-oxidant synthesis on the specific surface area of perovskite-type oxides LaBO{sub 3} (BMn, Ni, Fe) for total oxidation of ethanol. The perovskite-type oxides were characterized by X-ray diffraction, nitrogen adsorption (BET method), thermogravimetric analysis (TGA-DTA), TPR and X-ray photoelectron spectroscopy (XPS). Through method involving the coprecipitation-oxidant was possible to obtain catalysts with different BET specific surface areas, of 33-51 m{sup 2}/g. The results of the catalytic test confirmed that all oxides investigated in this work have specific catalytic activity for total oxidation of ethanol, though the temperatures for total conversion change for each transition metal. (author)

  19. Negative plate macropore surfaces in lead-acid batteries: Porosity, Brunauer-Emmett-Teller area, and capacity

    Energy Technology Data Exchange (ETDEWEB)

    D' Alkaine, C.V.; de O. Brito, G.A. [Group of Electrochemistry and Polymers, DQ-UFSCar, Rodovia Washington Luis, Km 235, CP 676, 13565-905 Sao Carlos (SP) (Brazil)

    2009-06-01

    We propose an explanation for the production of an electrochemically active area during the electrochemical formation of lead-acid battery negative plates based on solid-state reactions. Our proposal is supported by experimental data. This study includes a critical review of the literature on charge/discharge mechanisms, porosity, and BET area. The critical review, through the latter two parameters, indicates the existence of both macro and micropores in positive plates, but only macropores in negative plates, with characteristic surface roughness. In the present paper the surface sulfation of the precursor is controlled using various acidic, neutral and alkaline solutions during an electrochemical formation process that does not include soaking. Our results confirm that variable roughness can be produced at the negative plate macropore surfaces. The morphological changes produced by different formation conditions are assessed by measuring the macroporosity, BET area, and capacity of single negative plates. Based on these concepts, a method was developed and applied to measure independently the contributions of geometrical surface macroporosity and roughness to the negative plate capacity. (author)

  20. T-bet- and STAT4-dependent IL-33 receptor expression directly promotes antiviral Th1 cell responses.

    Science.gov (United States)

    Baumann, Claudia; Bonilla, Weldy V; Fröhlich, Anja; Helmstetter, Caroline; Peine, Michael; Hegazy, Ahmed N; Pinschewer, Daniel D; Löhning, Max

    2015-03-31

    During infection, the release of damage-associated molecular patterns, so-called "alarmins," orchestrates the immune response. The alarmin IL-33 plays a role in a wide range of pathologies. Upon release, IL-33 signals through its receptor ST2, which reportedly is expressed only on CD4(+) T cells of the Th2 and regulatory subsets. Here we show that Th1 effector cells also express ST2 upon differentiation in vitro and in vivo during lymphocytic choriomeningitis virus (LCMV) infection. The expression of ST2 on Th1 cells was transient, in contrast to constitutive ST2 expression on Th2 cells, and marked highly activated effector cells. ST2 expression on virus-specific Th1 cells depended on the Th1-associated transcription factors T-bet and STAT4. ST2 deficiency resulted in a T-cell-intrinsic impairment of LCMV-specific Th1 effector responses in both mixed bone marrow-chimeric mice and adoptive cell transfer experiments. ST2-deficient virus-specific CD4(+) T cells showed impaired expansion, Th1 effector differentiation, and antiviral cytokine production. Consequently, these cells mediated little virus-induced immunopathology. Thus, IL-33 acts as a critical and direct cofactor to drive antiviral Th1 effector cell activation, with implications for vaccination strategies and immunotherapeutic approaches.

  1. Development of a certified reference material for specific surface area of quartz sand

    Directory of Open Access Journals (Sweden)

    Egor P Sobina

    2017-01-01

    Full Text Available The paper presents results of conducting research on the development of a certified reference material (CRM for specific surface area of quartz sand, which is practically non-porous and therefore has low specific surface area value ~ 0.8 m2/g. The standard uncertainty due to RM inhomogeneity, the standard uncertainty due to RM instability, as well as the standard uncertainty due to characterization were estimated using the State Primary Standard GET 210‑2014 for Units of Specific Absorption of Gases, Specific Surface Area, Specific Volume, and Pore Size of Solid Substances and Materials. The metrological characteristics of the CRM were determined using a low-temperature gas adsorption method. Krypton was used as an adsorbate to increase measurement accuracy.

  2. BetOnMath azzardo e matematica a scuola

    CERN Document Server

    Andrà, Chiara; Verani, Marco

    2016-01-01

    Il libro ha origine dall'attività svolta durante il progetto "BetOnMath", un'esperienza di Matematica Civile finalizzata alla prevenzione dell'abuso di gioco d'azzardo tra gli studenti della scuola secondaria di secondo grado attraverso un insegnamento innovativo della matematica. In particolare, durante il progetto gli autori del libro hanno sviluppato un percorso didattico modulare sulla matematica del gioco d'azzardo che gli insegnanti di matematica delle scuole secondarie possono utilizzare sia per introdurre gli strumenti di base del calcolo delle probabilità sia per sensibilizzare sui rischi legati al gioco d'azzardo. Il libro descrive i pilastri metodologici e concettuali che hanno guidato la concezione e dato forma al percorso didattico, ovvero la centralità del ruolo dell'insegnante, l'uso dei simulatori di gioco, l'importanza delle attività di gruppo e il ruolo delle emozioni nell'affrontare e comprendere nuovi concetti matematici. Nel libro, ciascuno di questi pilastri è trattato sia mediante ...

  3. Resistência ao fogo de vigas parcialmente embebidas com betão

    OpenAIRE

    Piloto, P.A.G.; Gavilan, Ana; Mesquita, L.M.R.

    2011-01-01

    Neste artigo serão apresentados resultados dos ensaios de resistência ao fogo de elementos de viga parcialmente embebidos com betão. Os elementos de viga foram ensaiados à flexão, com aplicação de uma carga constante localizada a meio vão, submetida a uma curva de incêndio nominal ISO 834, [1-2]. Foram determinados os tempos de resistência ao fogo, as temperaturas críticas e os modos de colapso para cada grau de utilização.

  4. Specific capture of target bacteria onto sensor surfaces for infectious disease diagnosis

    International Nuclear Information System (INIS)

    Kim, Jong-Hoon; Inoue, Shinnosuke; Chung, Jae-Hyun; Cangelosi, Gerard A; Lee, Kyong-Hoon

    2014-01-01

    A long-sought goal for infectious disease care is a rapid and accurate diagnostic tool that is compatible with the needs of low-resource settings. To identify target biomarkers of infectious diseases, immunoassays utilizing the binding affinity between antigen and antibody have been widely used. In immunoassays, the interaction between antigen and antibody on sensor surfaces should be precisely controlled for specific identification of targets. This paper studies the specific capturing mechanisms of target bacteria onto sensor surfaces through investigation of combined effects of capillary action and binding affinity. As a model system, cells of both Escherichia coli and the Bacillus Calmette-Guérin strain of Mycobacterium bovis were used to study specific and nonspecific capturing mechanisms onto a microtip sensor. The capillary action was observed to arrange the concentrated cells onto the two-dimensional sensor surface. Due to the capillary-induced organization of target cells on the antibody-functionalized sensor surface, the number of the captured target cells was three times greater than that of the non-targeted cells. The capturing and detection capabilities varied with the width of a microtip. The specific capturing mechanism can be used to enhance the sensitivity and specificity of an immunoassay. (paper)

  5. BET bromodomain inhibition rescues erythropoietin differentiation of human erythroleukemia cell line UT7

    International Nuclear Information System (INIS)

    Goupille, Olivier; Penglong, Tipparat; Lefèvre, Carine; Granger, Marine; Kadri, Zahra; Fucharoen, Suthat; Maouche-Chrétien, Leila; Leboulch, Philippe; Chrétien, Stany

    2012-01-01

    Highlights: ► UT7 erythroleukemia cells are known to be refractory to differentiate. ► Brief JQ1 treatment initiates the first steps of erythroid differentiation program. ► Engaged UT7 cells then maturate in the presence of erythropoietin. ► Sustained JQ1 treatment inhibits both proliferation and erythroid differentiation. -- Abstract: Malignant transformation is a multistep process requiring oncogenic activation, promoting cellular proliferation, frequently coupled to inhibition of terminal differentiation. Consequently, forcing the reengagement of terminal differentiation of transformed cells coupled or not with an inhibition of their proliferation is a putative therapeutic approach to counteracting tumorigenicity. UT7 is a human leukemic cell line able to grow in the presence of IL3, GM-CSF and Epo. This cell line has been widely used to study Epo-R/Epo signaling pathways but is a poor model for erythroid differentiation. We used the BET bromodomain inhibition drug JQ1 to target gene expression, including that of c-Myc. We have shown that only 2 days of JQ1 treatment was required to transitory inhibit Epo-induced UT7 proliferation and to restore terminal erythroid differentiation. This study highlights the importance of a cellular erythroid cycle break mediated by c-Myc inhibition before initiation of the erythropoiesis program and describes a new model for BET bromodomain inhibitor drug application.

  6. BET bromodomain inhibition rescues erythropoietin differentiation of human erythroleukemia cell line UT7

    Energy Technology Data Exchange (ETDEWEB)

    Goupille, Olivier [CEA, Institute of Emerging Diseases and Innovative Therapies, Fontenay-aux-Roses (France); UMR INSERM U.962, University Paris XI, CEA, Fontenay-aux-Roses (France); Penglong, Tipparat [CEA, Institute of Emerging Diseases and Innovative Therapies, Fontenay-aux-Roses (France); UMR INSERM U.962, University Paris XI, CEA, Fontenay-aux-Roses (France); Thalassemia Research Center and Department of Clinical Pathology, Faculty of Medicine, Ramathibodi Hospital, Mahidol University (Thailand); Lefevre, Carine; Granger, Marine; Kadri, Zahra [CEA, Institute of Emerging Diseases and Innovative Therapies, Fontenay-aux-Roses (France); UMR INSERM U.962, University Paris XI, CEA, Fontenay-aux-Roses (France); Fucharoen, Suthat [Thalassemia Research Center and Department of Clinical Pathology, Faculty of Medicine, Ramathibodi Hospital, Mahidol University (Thailand); Maouche-Chretien, Leila [CEA, Institute of Emerging Diseases and Innovative Therapies, Fontenay-aux-Roses (France); UMR INSERM U.962, University Paris XI, CEA, Fontenay-aux-Roses (France); Leboulch, Philippe [CEA, Institute of Emerging Diseases and Innovative Therapies, Fontenay-aux-Roses (France); UMR INSERM U.962, University Paris XI, CEA, Fontenay-aux-Roses (France); Genetics Division, Department of Medicine, Brigham and Women' s Hospital and Harvard Medical School, Boston, MA (United States); Chretien, Stany, E-mail: stany.chretien@cea.fr [CEA, Institute of Emerging Diseases and Innovative Therapies, Fontenay-aux-Roses (France); UMR INSERM U.962, University Paris XI, CEA, Fontenay-aux-Roses (France)

    2012-12-07

    Highlights: Black-Right-Pointing-Pointer UT7 erythroleukemia cells are known to be refractory to differentiate. Black-Right-Pointing-Pointer Brief JQ1 treatment initiates the first steps of erythroid differentiation program. Black-Right-Pointing-Pointer Engaged UT7 cells then maturate in the presence of erythropoietin. Black-Right-Pointing-Pointer Sustained JQ1 treatment inhibits both proliferation and erythroid differentiation. -- Abstract: Malignant transformation is a multistep process requiring oncogenic activation, promoting cellular proliferation, frequently coupled to inhibition of terminal differentiation. Consequently, forcing the reengagement of terminal differentiation of transformed cells coupled or not with an inhibition of their proliferation is a putative therapeutic approach to counteracting tumorigenicity. UT7 is a human leukemic cell line able to grow in the presence of IL3, GM-CSF and Epo. This cell line has been widely used to study Epo-R/Epo signaling pathways but is a poor model for erythroid differentiation. We used the BET bromodomain inhibition drug JQ1 to target gene expression, including that of c-Myc. We have shown that only 2 days of JQ1 treatment was required to transitory inhibit Epo-induced UT7 proliferation and to restore terminal erythroid differentiation. This study highlights the importance of a cellular erythroid cycle break mediated by c-Myc inhibition before initiation of the erythropoiesis program and describes a new model for BET bromodomain inhibitor drug application.

  7. Adsorption of water vapour and the specific surface area of arctic zone soils (Spitsbergen)

    Science.gov (United States)

    Cieśla, Jolanta; Sokołowska, Zofia; Witkowska-Walczak, Barbara; Skic, Kamil

    2018-01-01

    Water vapour/nitrogen adsorption were investigated and calculated the specific surface areas of arctic-zone soil samples (Turbic Cryosols) originating from different micro-relief forms (mud boils, cell forms and sorted circles) and from different depths. For the characterisation of the isotherms obtained for arctic soils, the Brunauer-Emmet-Teller model was then compared with the two other models (Aranovich-Donohue and Guggenheim-Anderson-de Boer) which were developed from Brunauer-Emmet-Teller. Specific surface area was calculated using the Brunauer-Emmet-Teller model at p p0-1 range of 0.05-0.35 for the water vapour desorption and nitrogen adsorption isotherms. The values of total specific surface area were the highest in Cryosols on mud boils, lower on cell forms, and the lowest on sorted circles. Such tendency was observed for the results obtained by both the water vapour and nitrogen adsorption. The differences in the values of specific surface area at two investigated layers were small. High determination coefficients were obtained for relationships between the specific surface areas and contents of clay and silt fraction in Cryosols. No statistically significant correlation between the total carbon amount and the values of specific surface area in Cryosols has been found.

  8. The influence of surface integrin binding patterns on specific biomaterial-cell interactions

    Science.gov (United States)

    Beranek, Maggi Marie

    As the future of biomaterials progresses toward bioactivity, the biomaterial surface must control non-specific protein adsorption and encourage selective protein and cell adsorption. Integrins alphavbeta3, alpha 1beta1, alpha5beta1 and alpha Mbeta2 are expressed on cells involved in endothelialization, inflammation, and intimal hyperplasia. These cellular events play a vital role in biomaterial biocompatibility, especially in the vascular environment. The overall hypothesis of these studies is that biomaterial surfaces exhibit selective integrin binding, which then specifies differential cell binding. To test this hypothesis, four specific aims were developed. The first aim was designed to determine whether metal and polymeric biomaterials exhibit selective integrin binding. The tested materials included 316L stainless steel, nitinol, gold, Elgiloy RTM, poly(D, L-lactide-co-glycolide), polycarbonate urethane and expanded polytetrafluoroethylene. Discrete integrin binding patterns were detected microscopically using integrin specific fluorescent antibodies. Stainless steel exhibited high level integrin alpha1beta 1 and low level integrin alphaMbeta2 binding pattern. This suggests that this metal surface should selectively encourage endothelial cell to inflammatory cell binding. In contrast, gold bound ten times the amount of integrin alphaMbeta2 compared to integrin alpha1beta1, which should encourage inflammatory cell adhesion. The 65/35 poly(D, L-lactide-co-glycolide) was the only polymeric biomaterial tested that had integrin binding levels comparable to metal biomaterials. Based on these observations, a combinational biomaterial with a surface pattern of 65/35 poly(D, L-lactide-co-glycolide) dots on a 316L stainless steel background was created. A pattern of high level integrin alpha1beta1 binding and low level integrin alpha Mbeta2 binding on this combinational surface indicates that this surface should selectively favor endothelial cell binding. In the second

  9. Modeling the adsorption of metal ions (Cu 2+, Ni 2+, Pb 2+) onto ACCs using surface complexation models

    Science.gov (United States)

    Faur-Brasquet, Catherine; Reddad, Zacaria; Kadirvelu, Krishna; Le Cloirec, Pierre

    2002-08-01

    Activated carbon cloths (ACCs), whose efficiency has been demonstrated for microorganics adsorption from water, were here studied in the removal of metal ions from aqueous solution. Two ACCs are investigated, they are characterized in terms of porosity parameters (BET specific surface area, percentage of microporosity) and chemical characteristics (acidic surface groups, acidity constants, point of zero charge). A first part consists in the experimental study of three metal ions removal (Cu 2+, Ni 2+ and Pb 2+) in a batch reactor. Isotherms modeling by Freundlich and Brunauer-Emmett-Teller (BET) equations enables the following adsorption order: Cu 2+>Ni 2+>Pb 2+ to be determined for adsorption capacities on a molar basis. It may be related to adsorbates characteristics in terms of electronegativity and ionic radius. The influence of adsorbent's microporosity is also shown. Adsorption experiments carried out for pH values ranging from 2 to 10 demonstrate: (i) an adsorption occurring below the precipitation pH; (ii) the strong influence of pH, with a decrease of electrostatic repulsion due to the formation of less charged hydrolyzed species coupled with a decrease of activated carbon surface charge as pH increases. The second part focuses on the modeling of adsorption versus the pH experimental data by the diffuse layer model (DLM) using Fiteql software. The model is efficient to describe the system behavior in the pH range considered. Regarding complexation constants, they show the following affinity for ACC: Pb 2+>Cu 2+>Ni 2+. They are related to initial concentrations used for the three metal ions.

  10. Effects of engineered nano-titanium dioxide on pore surface properties and phosphorus adsorption of sediment: its environmental implications.

    Science.gov (United States)

    Luo, Zhuanxi; Wang, Zhenhong; Wei, Qunshan; Yan, Changzhou; Liu, Feng

    2011-09-15

    Understanding the environmental safety and human health implications of engineered nanoparticles (ENPs) is of worldwide importance. As an important ENPs, engineered nano-TiO(2) (Enano-TiO(2)) may have been substantially deposited in aquatic sediments because of its widely uses. Sediment pore surface properties would be thus significantly influenced due to the large surface area of Enano-TiO(2). In this study, Enano-TiO(2) was found to greatly impact on sediment pore surface properties. The attachment of Enano-TiO(2) particles to sediment surfaces enhanced markedly BET specific surface area and t-Plot external specific surface area, and thereby increased sediment phosphorus (P) adsorption maximum (S(max)). Contrarily, the fill of Enano-TiO(2) particles into the micropores of sediments could significantly reduce t-Plot micropore specific surface area, and cause slight decrease in sediment P binding energy (K). Clearly, P sorbed in sediment would be easily released because of the decreasing P binding energy of the sediment with elevated Enano-TiO(2). Enano-TiO(2) would thus cause aggravated endogenous pollution in water if such sediment was re-suspended on disturbance. The results obtained in this study contribute to our increasing knowledge of how to regulate physicochemical behavior of pollutants in sediments under the influences of Enano-TiO(2) and/or similar ENPs. Copyright © 2011 Elsevier B.V. All rights reserved.

  11. Identification of variant-specific surface proteins in Giardia muris trophozoites.

    Science.gov (United States)

    Ropolo, Andrea S; Saura, Alicia; Carranza, Pedro G; Lujan, Hugo D

    2005-08-01

    Giardia lamblia undergoes antigenic variation, a process that might allow the parasite to evade the host's immune response and adapt to different environments. Here we show that Giardia muris, a related species that naturally infects rodents, possesses multiple variant-specific surface proteins (VSPs) and expresses VSPs on its surface, suggesting that it undergoes antigenic variation similar to that of G. lamblia.

  12. Identification of Variant-Specific Surface Proteins in Giardia muris Trophozoites

    OpenAIRE

    Ropolo, Andrea S.; Saura, Alicia; Carranza, Pedro G.; Lujan, Hugo D.

    2005-01-01

    Giardia lamblia undergoes antigenic variation, a process that might allow the parasite to evade the host's immune response and adapt to different environments. Here we show that Giardia muris, a related species that naturally infects rodents, possesses multiple variant-specific surface proteins (VSPs) and expresses VSPs on its surface, suggesting that it undergoes antigenic variation similar to that of G. lamblia.

  13. Physical adsorption vs. chemical binding of undecylenic acid on porous silicon surface: a comparative study of differently functionalized materials

    Energy Technology Data Exchange (ETDEWEB)

    Salonen, J.; Lehto, V.P. [University of Turku (Finland). Department of Physics; Chirvony, V.; Matveeva, E. [Nanophotonics Technology Center, Technical University of Valencia (Spain); Pastor, E.

    2009-07-15

    To imply miscibility to porous silicon (PSi) used for biomedical purposes a number of functionalization methods are employed. In order to distinguish between a non-specific surfactant-like interaction (physical sorption) and chemical binding of unsaturated chemicals (undecylenic acid, UD) to H-terminated PSi surface we studied the two differently treated materials. Differential scanning calorimetry (DSC) and thermogravimetry (TGA), BET and FTIR measurements were performed with the PSi powder samples (n+ doped). Changes in surface area, weight loss, calorific effect and chemical composition that accompanied the thermal treatment have shown that the physisorbed UD molecules undergo a chemical process (binding) with the Si-H{sub x} surface groups at about 150 C in both, N{sub 2} inert atmosphere and in a synthetic air, oxidative atmosphere. Controlled conversion of physically sorbed molecules to the chemically attached ones is discussed with respect to methods of surface modification of PSi materials for increasing their biocompatibility. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  14. Optimal condition for fabricating superhydrophobic Aluminum surfaces with controlled anodizing processes

    Science.gov (United States)

    Saffari, Hamid; Sohrabi, Beheshteh; Noori, Mohammad Reza; Bahrami, Hamid Reza Talesh

    2018-03-01

    A single step anodizing process is used to produce micro-nano structures on Aluminum (1050) substrates with sulfuric acid as electrolyte. Therefore, surface energy of the anodized layer is reduced using stearic acid modification. Undoubtedly, effects of different parameters including anodizing time, electrical current, and type and concentration of electrolyte on the final contact angle are systemically studied and optimized. Results show that anodizing current of 0.41 A, electrolyte (sulfuric acid) concentration of 15 wt.% and anodizing time of 90 min are optimal conditions which give contact angle as high as 159.2° and sliding angle lower than 5°. Moreover, the study reveals that adding oxalic acid to the sulfuric acid cannot enhance superhydrophobicity of the samples. Also, scanning electron microscopy images of samples show that irregular (bird's nest) structures present on the surface instead of high-ordered honeycomb structures expecting from normal anodizing process. Additionally, X-ray diffraction analysis of the samples shows that only amorphous structures present on the surface. The Brunauer-Emmett-Teller (BET) specific surface area of the anodized layer is 2.55 m2 g-1 in optimal condition. Ultimately, the surface keeps its hydrophobicity in air and deionized water (DIW) after one week and 12 weeks, respectively.

  15. Long-range correlations in an online betting exchange for a football tournament

    Science.gov (United States)

    Hardiman, Stephen J.; Richmond, Peter; Hutzler, Stefan

    2010-10-01

    We analyze the changes in the market odds of football matches in an online betting exchange, Betfair.com. We identify the statistical differences between the returns that occur when the game play is under way, which we argue are driven by match events, and the returns that occur during half-time, which we ascribe to a trader-driven noise. Furthermore, using detrended fluctuation analysis we identify anti-persistence (Hurst exponent H0.5) in the volatilities, which we attribute to the trader-driven noise. The time series of trading volume are found to be short-memory processes.

  16. Characterisation and surface reactions of iron oxides and fluorapatite in aqueous suspensions

    OpenAIRE

    Jarlbring, Mathias

    2004-01-01

    The final objective of this study is to produce chemical models of flotation- like systems, including oxidation products of magnetite (maghemite and hematite) together with apatite. This is started by investigating the acid base properties, surface complexation and surface characteristics of the systems hematite-H+ and maghemite-H+ (paper I), fluorapatite-OH- (paper II) and a mixed system of maghemite-fluorapatite-OH- (paper III). Synthetic minerals were prepared and characterised with BET, S...

  17. Modification of surface/neuron interfaces for neural cell-type specific responses: a review

    International Nuclear Information System (INIS)

    Chen, Cen; Kong, Xiangdong; Lee, In-Seop

    2016-01-01

    Surface/neuron interfaces have played an important role in neural repair including neural prostheses and tissue engineered scaffolds. This comprehensive literature review covers recent studies on the modification of surface/neuron interfaces. These interfaces are identified in cases both where the surfaces of substrates or scaffolds were in direct contact with cells and where the surfaces were modified to facilitate cell adhesion and controlling cell-type specific responses. Different sources of cells for neural repair are described, such as pheochromocytoma neuronal-like cell, neural stem cell (NSC), embryonic stem cell (ESC), mesenchymal stem cell (MSC) and induced pluripotent stem cell (iPS). Commonly modified methods are discussed including patterned surfaces at micro- or nano-scale, surface modification with conducting coatings, and functionalized surfaces with immobilized bioactive molecules. These approaches to control cell-type specific responses have enormous potential implications in neural repair. (paper)

  18. Species specific isotope dilution for the accurate and SI traceable determination of arsenobetaine and methylmercury in cuttlefish and prawn

    International Nuclear Information System (INIS)

    Kumkrong, Paramee; Thiensong, Benjaporn; Le, Phuong Mai; McRae, Garnet; Windust, Anthony; Deawtong, Suladda; Meija, Juris; Maxwell, Paulette; Yang, Lu; Mester, Zoltán

    2016-01-01

    Methods based on species specific isotope dilution were developed for the accurate and SI traceable determination of arsenobetaine (AsBet) and methylmercury (MeHg) in prawn and cuttlefish tissues by LC-MS/MS and SPME GC-ICPMS. Quantitation of AsBet and MeHg were achieved by using a "1"3C-enriched AsBet spike (NRC CRM CBET-1) and an enriched spike of Me"1"9"8Hg (NRC CRM EMMS-1), respectively, wherein analyte mass fractions in enriched spikes were determined by reverse isotope dilution using natural abundance AsBet and MeHg primary standards. Purity of these primary standards were characterized by quantitative "1H-NMR with the use of NIST SRM 350b benzoic acid as a primary calibrator, ensuring the final measurement results traceable to SI. Validation of employed methods of ID LC-MS/MS and ID SPME GC-ICPMS was demonstrated by analysis of several biological CRMs (DORM-4, TORT-3, DOLT-5, BCR-627 and BCR-463) with satisfying results. The developed methods were applied for the determination of AsBet and MeHg in two new certified reference materials (CRMs) prawn (PRON-1) and cuttlefish (SQID-1) produced jointly by Thailand Institute of Scientific and Technological Research (TISTR) and National Research Council Canada (NRC). With additional measurements of AsBet using LC-ICPMS with standard additions calibration and external calibration at NRC and TISTR, respectively, certified values of 1.206 ± 0.058 and 13.96 ± 0.54 mg kg"−"1 for AsBet as As (expanded uncertainty, k = 2) were obtained for the new CRMs PRON-1 and SQID-1, respectively. The reference value of 0.324 ± 0.028 mg kg"−"1 as Hg (expanded uncertainty, k = 2) for MeHg was obtained for the SQID-1 based on the results obtained by ID SPME GC-ICPMS method only, whereas MeHg in PRON-1 was found to be < 0.015 mg kg"−"1. It was found that AsBet comprised 69.7% and 99.0% of total As in the prawn and cuttlefish, respectively, whereas MeHg comprised 94.5% of total Hg in cuttlefish. - Highlights:

  19. Complexity Triggered by Economic Globalisation— The Issue of On-Line Betting-Related Match Fixing

    OpenAIRE

    Wladimir Andreff

    2017-01-01

    Complexity in mainstream economics consists in high intermediary consumption of mathematics. A new approach to complexity economics dwells upon path-dependent global systems; their emergence and evolving organisation. The focus here is on the complexity of the real economic world due to globalisation. On-line betting related match-fixing is a case in point about which the article presents non-exhaustive empirical evidence and shows how it is analysed with the standard model of the economics o...

  20. Preparation of Active Absorbent for Flue Gas Desulfurization From Coal Bottom Ash: Effect of Absorbent Preparation Variables

    Directory of Open Access Journals (Sweden)

    Chang Chin Li, Lee Keat Teong, Subhash Bhatia and Abdul Rahman Mohamed

    2012-08-01

    Full Text Available An active absorbent for flue gas desulfurization was prepared from coal bottom ash, calcium oxide (CaO and calcium sulfate by hydro-thermal process. The absorbent was examined for its micro-structural properties. The experiments conducted were based on Design Of Experiments (DOE according to 23 factorial design. The effect of various absorbent preparation variables such as ratio of CaO to bottom ash (A, hydration temperature (B and hydration period (C towards the BET (Brunauer-Emmett-Teller specific surface area of the absorbent were studied. At a CaO to bottom ash ratio = 2, hydration temperature = 200 ?C and hydration period = 10 hrs, absorbent with a surface area of 90.1 m2/g was obtained. Based on the analysis of the factorial design, it was concluded that factor A and C as well as the interaction of factors ABC and BC are the significant factors that effect the BET surface area of the absorbent. A linear mathematical model that describes the relation between the independent variables and interaction between variables towards the BET specific surface area of the absorbent was also developed. Analysis of variance (ANOVA showed that the model was significant at 1% level.Key Words: Absorbent, Bottom Ash, Design Of Experiments, Desulfurization, Surface Area.

  1. Robot Towed Shortwave Infrared Camera for Specific Surface Area Retrieval of Surface Snow

    Science.gov (United States)

    Elliott, J.; Lines, A.; Ray, L.; Albert, M. R.

    2017-12-01

    Optical grain size and specific surface area are key parameters for measuring the atmospheric interactions of snow, as well as tracking metamorphosis and allowing for the ground truthing of remote sensing data. We describe a device using a shortwave infrared camera with changeable optical bandpass filters (centered at 1300 nm and 1550 nm) that can be used to quickly measure the average SSA over an area of 0.25 m^2. The device and method are compared with calculations made from measurements taken with a field spectral radiometer. The instrument is designed to be towed by a small autonomous ground vehicle, and therefore rides above the snow surface on ultra high molecular weight polyethylene (UHMW) skis.

  2. Increased numbers of pre-existing memory CD8 T cells and decreased T-bet expression can restrain terminal differentiation of secondary effector and memory CD8 T cells1

    Science.gov (United States)

    Joshi, Nikhil S.; Cui, Weiguo; Dominguez, Claudia; Chen, Jonathan H.; Hand, Timothy W.; Kaech, Susan M.

    2011-01-01

    Memory CD8 T cells acquire TEM properties following reinfection, and may reach terminally differentiated, senescent states (“Hayflick limit”) after multiple infections. The signals controlling this process are not well understood, but we found that the degree of 2o effector and memory CD8 T cell differentiation was intimately linked to the amount of T-bet expressed upon reactivation and pre-existing memory CD8 T cell number (i.e., 1o memory CD8 T cell precursor frequency) present during secondary infection. Compared to naïve cells, memory CD8 T cells were predisposed towards terminal effector (TE) cell differentiation because they could immediately respond to IL-12 and induce T-bet, even in the absence of antigen. TE cell formation following 2o or 3o infections was dependent on increased T-bet expression because T-bet+/− cells were resistant to these phenotypic changes. Larger numbers of pre-existing memory CD8 T cells limited the duration of 2o infection and the amount of IL-12 produced, and consequently, this reduced T-bet expression and the proportion of 2o TE CD8 T cells that formed. Together, these data show that, over repeated infections, memory CD8 T cell quality and proliferative fitness is not strictly determined by the number of serial encounters with antigen or cell divisions, but is a function of the CD8 T cell differentiation state, which is genetically controlled in a T-bet-dependent manner. This differentiation state can be modulated by pre-existing memory CD8 T cell number and the intensity of inflammation during reinfection. These results have important implications for vaccinations involving prime-boost strategies. PMID:21930973

  3. Collapse of Cytolytic Potential in SIV-Specific CD8+ T Cells Following Acute SIV Infection in Rhesus Macaques.

    Directory of Open Access Journals (Sweden)

    Emily R Roberts

    2016-12-01

    Full Text Available Poor maintenance of cytotoxic factor expression among HIV-specific CD8+ T cells, in part caused by dysregulated expression of the transcription factor T-bet, is associated with HIV disease progression. However, the precise evolution and context in which CD8+ T cell cytotoxic functions become dysregulated in HIV infection remain unclear. Using the rhesus macaque (RM SIV infection model, we evaluated the kinetics of SIV-specific CD8+ T cell cytolytic factor expression in peripheral blood, lymph node, spleen, and gut mucosa from early acute infection through chronic infection. We identified rapid acquisition of perforin and granzyme B expression in SIV-specific CD8+ T cells in blood, secondary lymphoid tissues and gut mucosa that collapsed rapidly during the transition to chronic infection. The evolution of this expression profile was linked to low expression of T-bet and occurred independent of epitope specificity, viral escape patterns and tissue origin. Importantly, during acute infection SIV-specific CD8+ T cells that maintained T-bet expression retained the ability to express granzyme B after stimulation, but this relationship was lost in chronic infection. Together, these data demonstrate the loss of cytolytic machinery in SIV-specific CD8+ T cells in blood and at tissue sites of viral reservoir and active replication during the transition from acute to chronic infection. This phenomenon occurs despite persistent high levels of viremia suggesting that an inability to maintain properly regulated cytotoxic T cell responses in all tissue sites enables HIV/SIV to avoid immune clearance, establish persistent viral reservoirs in lymphoid tissues and gut mucosa, and lead ultimately to immunopathogenesis and death.

  4. Sintering of uranium oxide of high specific surface area

    International Nuclear Information System (INIS)

    Bel, Alain; Francois, Bernard; Delmas, Roger; Caillat, Roger

    1959-01-01

    The extent to which a uranium oxide powder deriving from ammonium uranate or uranium peroxide lends itself to the sintering process depends largely on its specific surface area. When this is greater than 5 m 2 / g there is an optimum temperature for sintering in hydrogen. This temperature becomes less as the specific area of the powder is greater. Reprint of a paper published in Comptes rendus des seances de l'Academie des Sciences, t. 249, p. 1045-1047, sitting of 21 September 1959 [fr

  5. Conectores inovadores de elevado desempenho para estruturas mistas aço-betão

    OpenAIRE

    Duarte, Gonçalo Santos

    2015-01-01

    Dissertação de Mestrado Integrado em Engenharia Civil apresentada à Faculdade de Ciências e Tecnologia da Universidade de Coimbra A presente dissertação de Mestrado Integrado apresenta um estudo sobre conectores inovadores de elevado desempenho para estruturas mistas aço-betão. Esta tese tem forte ênfase em ensaios laboratoriais, tendo sido efectuados 8 ensaios push-out no Departamento de Engenharia Civil da Universidade de Coimbra, respeitando as especificações indicadas no Eu...

  6. Host-parasite coevolution can promote the evolution of seed banking as a bet-hedging strategy.

    Science.gov (United States)

    Verin, Mélissa; Tellier, Aurélien

    2018-04-20

    Seed (egg) banking is a common bet-hedging strategy maximizing the fitness of organisms facing environmental unpredictability by the delayed emergence of offspring. Yet, this condition often requires fast and drastic stochastic shifts between good and bad years. We hypothesize that the host seed banking strategy can evolve in response to coevolution with parasites because the coevolutionary cycles promote a gradually changing environment over longer times than seed persistence. We study the evolution of host germination fraction as a quantitative trait using both pairwise competition and multiple mutant competition methods, while the germination locus can be genetically linked or unlinked with the host locus under coevolution. In a gene-for-gene model of coevolution, hosts evolve a seed bank strategy under unstable coevolutionary cycles promoted by moderate to high costs of resistance or strong disease severity. Moreover, when assuming genetic linkage between coevolving and germination loci, the resistant genotype always evolves seed banking in contrast to susceptible hosts. Under a matching-allele interaction, both hosts' genotypes exhibit the same seed banking strategy irrespective of the genetic linkage between loci. We suggest host-parasite coevolution as an additional hypothesis for the evolution of seed banking as a temporal bet-hedging strategy. © 2018 The Author(s). Evolution © 2018 The Society for the Study of Evolution.

  7. Surface modification of sol–gel synthesized TiO{sub 2} nanoparticles induced by La-doping

    Energy Technology Data Exchange (ETDEWEB)

    Grujić-Brojčin, M., E-mail: myramyra@ipb.ac.rs [Institute of Physics, University of Belgrade, Pregrevica 118, 11080 Belgrade (Serbia); Armaković, S. [Department of Chemistry, Biochemistry and Environmental Protection, Faculty of Sciences, University of Novi Sad, Trg D. Obradovića 3, 21000 Novi Sad (Serbia); Tomić, N. [Institute of Physics, University of Belgrade, Pregrevica 118, 11080 Belgrade (Serbia); Abramović, B. [Department of Chemistry, Biochemistry and Environmental Protection, Faculty of Sciences, University of Novi Sad, Trg D. Obradovića 3, 21000 Novi Sad (Serbia); Golubović, A.; Stojadinović, B. [Institute of Physics, University of Belgrade, Pregrevica 118, 11080 Belgrade (Serbia); Kremenović, A. [Faculty of Mining and Geology, Laboratory for Crystallography, University of Belgrade, Đušina 7, 11000 Belgrade (Serbia); Babić, B. [Institute of Nuclear Sciences “Vinča”, University of Belgrade, 11001 Belgrade (Serbia); Dohčević-Mitrović, Z.; Šćepanović, M. [Institute of Physics, University of Belgrade, Pregrevica 118, 11080 Belgrade (Serbia)

    2014-02-15

    The influence of La-doping in the range of 0.5–6.0 mol% on structural and morphological properties of TiO{sub 2} nanopowders synthesized by sol–gel routine has been investigated by XRPD, AFM, EDS and BET measurements, as well as Raman spectroscopy. The XRPD and Raman measurements have revealed the anatase phase as dominant in all nanopowders, with crystallite size decreasing from ∼ 15 nm in pure TiO{sub 2} to ∼ 12 nm in La-doped samples. The BET data suggest that all samples are fully mesoporous, with mean pore diameters in the range of ∼ 6–8 nm. The specific surface area and the complexity of pore structure are greater in doped samples than in pure TiO{sub 2} sample. The spectroscopic ellipsometry has apparently shown that the band gap has been gradually increased with the increase of La content. The STM and STS techniques have been used successfully to evaluate the surface morphology and electronic properties of La-doped nanopowders. All investigated properties have been related to photocatalytic activity, tested in degradation of a metoprolol tartrate salt (0.05 mM), and induced by UV-radiation. All doped samples showed increased photocatalytic activity compared to pure TiO{sub 2}, among which the 0.65 mol% La-doped sample appeared to be the most efficient. - Highlights: • Effects of La-doping on structural, morphological and electronic properties of TiO{sub 2} nanopowders. • Surface morphology and electronic properties of La-doped nanopowders evaluated by STM/STS. • Spectroscopic ellipsometry shown gradual increase of bandgap with the increase of La content. • Photocatalytic activity of samples was tested in degradation of MET under UV light.

  8. Bet-hedging as a complex interaction among developmental instability, environmental heterogeneity, dispersal, and life-history strategy.

    Science.gov (United States)

    Scheiner, Samuel M

    2014-02-01

    One potential evolutionary response to environmental heterogeneity is the production of randomly variable offspring through developmental instability, a type of bet-hedging. I used an individual-based, genetically explicit model to examine the evolution of developmental instability. The model considered both temporal and spatial heterogeneity alone and in combination, the effect of migration pattern (stepping stone vs. island), and life-history strategy. I confirmed that temporal heterogeneity alone requires a threshold amount of variation to select for a substantial amount of developmental instability. For spatial heterogeneity only, the response to selection on developmental instability depended on the life-history strategy and the form and pattern of dispersal with the greatest response for island migration when selection occurred before dispersal. Both spatial and temporal variation alone select for similar amounts of instability, but in combination resulted in substantially more instability than either alone. Local adaptation traded off against bet-hedging, but not in a simple linear fashion. I found higher-order interactions between life-history patterns, dispersal rates, dispersal patterns, and environmental heterogeneity that are not explainable by simple intuition. We need additional modeling efforts to understand these interactions and empirical tests that explicitly account for all of these factors.

  9. Selective radiolabeling of cell surface proteins to a high specific activity

    International Nuclear Information System (INIS)

    Thompson, J.A.; Lau, A.L.; Cunningham, D.D.

    1987-01-01

    A procedure was developed for selective radiolabeling of membrane proteins on cells to higher specific activities than possible with available techniques. Cell surface amino groups were derivatized with 125 I-(hydroxyphenyl)propionyl groups via 125 I-sulfosuccinimidyl (hydroxyphenyl)propionate ( 125 II-sulfo-SHPP). This reagent preferentially labeled membrane proteins exposed at the cell surface of erythrocytes as assessed by the degree of radiolabel incorporation into erythrocyte ghost proteins and hemoglobin. Comparison with the lactoperoxidase-[ 125 I]iodide labeling technique revealed that 125 I-sulfo-SHPP labeled cell surface proteins to a much higher specific activity and hemoglobin to a much lower specific activity. Additionally, this reagent was used for selective radiolabeling of membrane proteins on the cytoplasmic face of the plasma membrane by blocking exofacial amino groups with uniodinated sulfo-SHPP, lysing the cells, and then incubating them with 125 I-sulfo-SHPP. Exclusive labeling of either side of the plasma membrane was demonstrated by the labeling of some marker proteins with well-defined spacial orientations on erythroctyes. Transmembrane proteins such as the epidermal growth factor receptor on cultured cells could also be labeled differentially from either side of the plasma membrane

  10. Selectivity/Specificity Improvement Strategies in Surface-Enhanced Raman Spectroscopy Analysis

    Directory of Open Access Journals (Sweden)

    Feng Wang

    2017-11-01

    Full Text Available Surface-enhanced Raman spectroscopy (SERS is a powerful technique for the discrimination, identification, and potential quantification of certain compounds/organisms. However, its real application is challenging due to the multiple interference from the complicated detection matrix. Therefore, selective/specific detection is crucial for the real application of SERS technique. We summarize in this review five selective/specific detection techniques (chemical reaction, antibody, aptamer, molecularly imprinted polymers and microfluidics, which can be applied for the rapid and reliable selective/specific detection when coupled with SERS technique.

  11. Surface modification of bone char for removal of formaldehyde from air

    Energy Technology Data Exchange (ETDEWEB)

    Rezaee, Abbas, E-mail: rezaee@modares.ac.ir [Environmental Health Department, Faculty of Medical Sciences, Tarbiat Modares University, Tehran (Iran, Islamic Republic of); Rangkooy, Hosseinali [Environmental Health Department, Faculty of Medical Sciences, Tarbiat Modares University, Tehran (Iran, Islamic Republic of); Occupational Health Department, Faculty of Health, Jondishapor Medical Sciences University, Ahvaz (Iran, Islamic Republic of); Jonidi-Jafari, Ahmad; Khavanin, Ali [Environmental Health Department, Faculty of Medical Sciences, Tarbiat Modares University, Tehran (Iran, Islamic Republic of)

    2013-12-01

    The aim of this study was to evaluate the adsorption performance of bone char (BC) modified with acetic acid for formaldehyde removal from polluted air. The porous structure, surface characteristics and functional groups involved in formaldehyde adsorption were determined using the Brunauer–Emmett–Teller (BET) method, scanning electron microscope (SEM) equipped with energy dispersive X-ray (EDX) and Fourier transform infrared spectroscopy (FTIR), respectively. It was found that the modified BC has a higher specific surface area than the original BC. The maximum surface area of the modified BC was 118.58 m{sup 2}/g. The FTIR spectrum of modified BC indicated that the hydroxyl and carboxyl groups on the BC surface played a significant role in the adsorption of formaldehyde by modified BC. The breakthrough, equilibrium time and adsorption capacity of modified BC were greater than the original BC. Moreover, the results showed that at initial concentrations of 20, 50, 100 and 200 mg/L, the equilibrium times for BC and modified BC were 85, 75, 65 and 45 min and 95, 85, 70 and 50 min, respectively. It seems that the formaldehyde adsorption capacity of modified BC depends on both physical and chemical properties. These results showed that modified BC can be used as an efficient adsorbent for formaldehyde removal.

  12. Comparison of chemical and physical properties of carbon blacks for sampling and analysis of environmental pollutants

    Energy Technology Data Exchange (ETDEWEB)

    Mastrogiacomo, A.R.; Ottaviani, M.F.; Pierini, E.; Cangiotti, M.; Mangani, F. [Ist. di Scienze Chimiche ' ' Fabrizio Bruner' ' dell' Univ. degli Studi di Urbino, Urbino (Italy); Mauro, M. [Dipt. di Chimica dell' Univ. degli Studi di Firenze, Firenze (Italy)

    2002-03-01

    Some of the most commonly employed carbon blocks (Carbograph 1, 2, 4, 5 from Lara and Carbopack X from Supelco), were evaluated by the BET surface characterization method for pore size distribution, porosity and specific surface. This information is often incomplete as furnished by manufacturers and is needed for a deeper understanding of carbon adsorption properties in chromatography. The data on surface characterization were obtained before and after graphitisation treatment (except for Carbopack X which could not be obtained in non-graphitized form). The nature of the active sites present on these carbons was investigated by BET analysis, atomic absorption and FT-IR. (orig.)

  13. BET, thermal degradation, and FTIR spectras of triazine polyamine polymers.

    Science.gov (United States)

    Can, Mustafa

    2017-04-01

    Here we show effect of the polyamine polymer chain length to BET isotherms. According to IUPAC classification [1], all three polymers are fitting type 1 physical adsorption isotherm with H3 hysteresis (except for EDA having H2 hysteresis). Moreover, TG and TGA analysis of polymers triazine-ethylenediamine (EDA) and triazine-triethylenetetramine (TETA) are provided. Due to the similarities of the structure, main decomposition temperatures are close to each other (between 593 K and 873 K). In order to understand change of FTIR spectra with adsorption and stripping Au(III), fresh, Au(III) adsorbed and recycled spectras of polymers measured. For further discussions about the effect of chain length to adsorption of Au(III) onto triazine polyamine polymer particles "Au (III) Uptake by Triazine Polyamine Polymers: Mechanism, Kinetic and Equilibrium Studies" Can et al. [2] (article in press).

  14. Aridity promotes bet hedging via delayed hatching: a case study with two temporary pond crustaceans along a latitudinal gradient.

    Science.gov (United States)

    Pinceel, Tom; Vanschoenwinkel, Bram; Hawinkel, Wouter; Tuytens, Karen; Brendonck, Luc

    2017-05-01

    Climate change does affect not only average rainfall and temperature but also their variation, which can reduce the predictability of suitable conditions for growth and reproduction. This situation is problematic for inhabitants of temporary waters whose reproductive success depends on rainfall and evaporation that determine the length of the aquatic phase. For organisms with long-lived dormant life stages, bet hedging models suggest that a fraction of these should stay dormant during each growing season to buffer against the probability of total reproductive failure in variable environments. Thus far, however, little empirical evidence supports this prediction in aquatic organisms. We study geographic variation in delayed hatching of dormant eggs in natural populations of two crustaceans, Branchinella longirostris and Paralimnadia badia, that occur in temporary rock pools along a 725 km latitudinal aridity gradient in Western Australia. Consistent with bet hedging theory, populations of both species were characterised by delayed hatching under common garden conditions and hatching fractions decreased towards the drier end of the gradient where the probability of reproductive success was shown to be lower. This decrease was most pronounced in the species with the longer maturation time, presumably because it is more sensitive to the higher prevalence of short inundations. Overall, these findings illustrate that regional variation in climate can be reflected in differential investment in bet hedging and hints at a higher importance of delayed hatching to persist when the climate becomes harsher. Such strategies could become exceedingly relevant as determinants of vulnerability under climate change.

  15. Species specific isotope dilution for the accurate and SI traceable determination of arsenobetaine and methylmercury in cuttlefish and prawn

    Energy Technology Data Exchange (ETDEWEB)

    Kumkrong, Paramee [National Research Council Canada, 1200 Montreal Rd, Ottawa, Ontario, K1A 0R6 (Canada); Thailand Institute of Scientific and Technological Research, 35 Mu 3 Tambon Khlong Ha, Amphoe Khlong Luang, Pathum Thani, 12120 (Thailand); Thiensong, Benjaporn [Thailand Institute of Scientific and Technological Research, 35 Mu 3 Tambon Khlong Ha, Amphoe Khlong Luang, Pathum Thani, 12120 (Thailand); Le, Phuong Mai; McRae, Garnet; Windust, Anthony [National Research Council Canada, 1200 Montreal Rd, Ottawa, Ontario, K1A 0R6 (Canada); Deawtong, Suladda [Thailand Institute of Scientific and Technological Research, 35 Mu 3 Tambon Khlong Ha, Amphoe Khlong Luang, Pathum Thani, 12120 (Thailand); Meija, Juris; Maxwell, Paulette [National Research Council Canada, 1200 Montreal Rd, Ottawa, Ontario, K1A 0R6 (Canada); Yang, Lu, E-mail: Lu.yang@nrc-cnrc.gc.ca [National Research Council Canada, 1200 Montreal Rd, Ottawa, Ontario, K1A 0R6 (Canada); Mester, Zoltán [National Research Council Canada, 1200 Montreal Rd, Ottawa, Ontario, K1A 0R6 (Canada)

    2016-11-02

    Methods based on species specific isotope dilution were developed for the accurate and SI traceable determination of arsenobetaine (AsBet) and methylmercury (MeHg) in prawn and cuttlefish tissues by LC-MS/MS and SPME GC-ICPMS. Quantitation of AsBet and MeHg were achieved by using a {sup 13}C-enriched AsBet spike (NRC CRM CBET-1) and an enriched spike of Me{sup 198}Hg (NRC CRM EMMS-1), respectively, wherein analyte mass fractions in enriched spikes were determined by reverse isotope dilution using natural abundance AsBet and MeHg primary standards. Purity of these primary standards were characterized by quantitative {sup 1}H-NMR with the use of NIST SRM 350b benzoic acid as a primary calibrator, ensuring the final measurement results traceable to SI. Validation of employed methods of ID LC-MS/MS and ID SPME GC-ICPMS was demonstrated by analysis of several biological CRMs (DORM-4, TORT-3, DOLT-5, BCR-627 and BCR-463) with satisfying results. The developed methods were applied for the determination of AsBet and MeHg in two new certified reference materials (CRMs) prawn (PRON-1) and cuttlefish (SQID-1) produced jointly by Thailand Institute of Scientific and Technological Research (TISTR) and National Research Council Canada (NRC). With additional measurements of AsBet using LC-ICPMS with standard additions calibration and external calibration at NRC and TISTR, respectively, certified values of 1.206 ± 0.058 and 13.96 ± 0.54 mg kg{sup −1} for AsBet as As (expanded uncertainty, k = 2) were obtained for the new CRMs PRON-1 and SQID-1, respectively. The reference value of 0.324 ± 0.028 mg kg{sup −1} as Hg (expanded uncertainty, k = 2) for MeHg was obtained for the SQID-1 based on the results obtained by ID SPME GC-ICPMS method only, whereas MeHg in PRON-1 was found to be < 0.015 mg kg{sup −1}. It was found that AsBet comprised 69.7% and 99.0% of total As in the prawn and cuttlefish, respectively, whereas MeHg comprised 94.5% of total Hg in

  16. Planar spatial correlations, anisotropy, and specific surface area of stationary random porous media

    International Nuclear Information System (INIS)

    Berryman, J.G.

    1998-01-01

    An earlier result of the author showed that an anisotropic spatial correlation function of a random porous medium could be used to compute the specific surface area when it is stationary as well as anisotropic by first performing a three-dimensional radial average and then taking the first derivative with respect to lag at the origin. This result generalized the earlier result for isotropic porous media of Debye et al. [J. Appl. Phys. 28, 679 (1957)]. The present article provides more detailed information about the use of spatial correlation functions for anisotropic porous media and in particular shows that, for stationary anisotropic media, the specific surface area can be related to the derivative of the two-dimensional radial average of the correlation function measured from cross sections taken through the anisotropic medium. The main concept is first illustrated using a simple pedagogical example for an anisotropic distribution of spherical voids. Then, a general derivation of formulas relating the derivative of the planar correlation functions to surface integrals is presented. When the surface normal is uniformly distributed (as is the case for any distribution of spherical voids), our formulas can be used to relate a specific surface area to easily measurable quantities from any single cross section. When the surface normal is not distributed uniformly (as would be the case for an oriented distribution of ellipsoidal voids), our results show how to obtain valid estimates of specific surface area by averaging measurements on three orthogonal cross sections. One important general observation for porous media is that the surface area from nearly flat cracks may be underestimated from measurements on orthogonal cross sections if any of the cross sections happen to lie in the plane of the cracks. This result is illustrated by taking the very small aspect ratio (penny-shaped crack) limit of an oblate spheroid, but holds for other types of flat surfaces as well

  17. Surface functionalization of SPR chip for specific molecular interaction analysis under flow condition

    Directory of Open Access Journals (Sweden)

    Tao Ma

    2017-03-01

    Full Text Available Surface functionalization of sensor chip for probe immobilization is crucial for the biosensing applications of surface plasmon resonance (SPR sensors. In this paper, we report a method circulating the dopamine aqueous solution to coat polydopamine film on sensing surface for surface functionalization of SPR chip. The polydopamine film with available thickness can be easily prepared by controlling the circulation time and the biorecognition elements can be immobilized on the polydopamine film for specific molecular interaction analysis. These operations are all performed under flow condition in the fluidic system, and have the advantages of easy implementation, less time consuming, and low cost, because the reagents and devices used in the operations are routinely applied in most laboratories. In this study, the specific absorption between the protein A probe immobilized on the sensing surface and human immunoglobulin G in the buffer is monitored based on this surface functionalization strategy to demonstrated its feasibility for SPR biosensing applications.

  18. Self-Assembly of 3D Fennel-Like Co3O4 with Thirty-Six Surfaces for High Performance Supercapacitor

    Directory of Open Access Journals (Sweden)

    Yanfang Li

    2017-01-01

    Full Text Available Three-dimensional (3D fennel-like cobalt oxide (II, III (Co3O4 particles with thirty-six surfaces on nickel foams were prepared via a simple hydrothermal synthesis method and its growth process was also researched. The crystalline structure and morphology were investigated by X-ray diffraction (XRD, scanning electron microscopy (SEM, and Raman spectroscopy. The Brunauer-Emmett-Teller (BET analysis revealed that 3D fennel-like Co3O4 particles have high specific surface area. Therefore, the special structure with thirty-six surfaces indicates the good electrochemical performance of the micron-nanometer material as electrode material for supercapacitors. The cyclic voltammetry (CV, galvanostatic charge-discharge, and electrochemical impedance spectroscopy (EIS were conducted to evaluate the electrochemical performances. Compared with other morphological materials of the similar sizes, the Co3O4 particles on nickel foam exhibit a high specific capacitance of 384.375 F·g−1 at the current density of 3 A·g−1 and excellent cycling stability of a capacitance retention of 96.54% after 1500 galvanostatic charge-discharge cycles in 6 M potassium hydroxide (KOH electrolyte.

  19. Problemas inversos na análise de estrururas de madeira-betão

    OpenAIRE

    Santo, Diogo Lopes

    2014-01-01

    Dissertação de Mestrado Integrado em Engenharia Civil apresentada à Faculdade de Ciências e Tecnologia da Universidade de Coimbra Neste trabalho, utiliza-se uma abordagem determinística num problema inverso com o objetivo de determinar parâmetros de rigidez num caso prático de uma laje mista madeira-betão onde são aplicadas cargas estáticas. Este objetivo surge no âmbito dos processos indiretos de identificação paramétrica a usar, por exemplo, em avaliações estruturais. A resolução dest...

  20. Free-standing and porous hierarchical nanoarchitectures constructed with cobalt cobaltite nanowalls for supercapacitors with high specific capacitances

    Science.gov (United States)

    Xiao, Yuanhua; Zhang, Aiqin; Liu, Shaojun; Zhao, Jihong; Fang, Shaoming; Jia, Dianzeng; Li, Feng

    2012-12-01

    Free-standing and porous hierarchical nanoarchitectures constructed with cobalt cobaltite (Co3O4) nanowalls have been successfully synthesized in large scale by calcining three dimensional (3D) hierarchical nanostructures consisting of single crystalline cobalt carbonate hydroxide hydrate - Co(CO3)0.5(OH)·0.11H2O nanowalls prepared with a solvothermal method. The step-by-step decomposition of the precursor can generate porous Co3O4 nanowalls with BET surface area of 88.34 m2 g-1. The as-prepared Co3O4 nanoarchitectures show superior specific capacitance to the most Co3O4 supercapacitor electrode materials to date. After continuously cycled for 1000 times of charge-discharge at 4 A g-1, the supercapacitors can retain ca 92.3% of their original specific capacitances. The excellent performances of the devices can be attributed to the porous and hierarchical 3D nanostructure of the materials.

  1. Power Spectral Density Specification and Analysis of Large Optical Surfaces

    Science.gov (United States)

    Sidick, Erkin

    2009-01-01

    The 2-dimensional Power Spectral Density (PSD) can be used to characterize the mid- and the high-spatial frequency components of the surface height errors of an optical surface. We found it necessary to have a complete, easy-to-use approach for specifying and evaluating the PSD characteristics of large optical surfaces, an approach that allows one to specify the surface quality of a large optical surface based on simulated results using a PSD function and to evaluate the measured surface profile data of the same optic in comparison with those predicted by the simulations during the specification-derivation process. This paper provides a complete mathematical description of PSD error, and proposes a new approach in which a 2-dimentional (2D) PSD is converted into a 1-dimentional (1D) one by azimuthally averaging the 2D-PSD. The 1D-PSD calculated this way has the same unit and the same profile as the original PSD function, thus allows one to compare the two with each other directly.

  2. China Minsheng Bank China's first non-state owned bank is one of the safest bets in the risky Chinese banking sector

    Institute of Scientific and Technical Information of China (English)

    BRADLEY GARDNER

    2008-01-01

    @@ Betting on China's banking sector is a risky proposition. High rates of overdue "problem" loans are more or less the norm, and financial reforms, while moving forward, are doing so at a snail's pace.

  3. Disruptive selection and bet-hedging in planktonic Foraminifera: Shell morphology as predictor of extinctions

    Directory of Open Access Journals (Sweden)

    Manuel F. G. Weinkauf

    2014-10-01

    Full Text Available Extinction is a remarkably difficult phenomenon to study under natural conditions. This is because the outcome of stress exposure and associated fitness reduction is not known until the extinction occurs and it remains unclear whether there is any phenotypic reaction of the exposed population that can be used to predict its fate. Here we take advantage of the fossil record, where the ecological outcome of stress exposure is known. Specifically, we analyze shell morphology of planktonic Foraminifera in sediment samples from the Mediterranean, during an interval preceding local extinctions. In two species representing different plankton habitats, we observe shifts in trait state and decrease in variance in association with non-terminal stress, indicating stabilizing selection. At terminal stress levels, immediately before extinction, we observe increased growth asymmetry and trait variance, indicating disruptive selection and bet-hedging. The pre-extinction populations of both species show a combination of trait states and trait variance distinct from all populations exposed to non-terminal levels of stress. This finding indicates that the phenotypic history of a population may allow the detection of threshold levels of stress, likely to lead to extinction. It is thus an alternative to population dynamics in studying and monitoring natural population ecology.

  4. Automatic selective feature retention in patient specific elastic surface registration

    CSIR Research Space (South Africa)

    Jansen van Rensburg, GJ

    2011-01-01

    Full Text Available The accuracy with which a recent elastic surface registration algorithm deforms the complex geometry of a skull is examined. This algorithm is then coupled to a line based algorithm as is frequently used in patient specific feature registration...

  5. Egg shell waste as heterogeneous nanocatalyst for biodiesel production: Optimized by response surface methodology.

    Science.gov (United States)

    Pandit, Priti R; Fulekar, M H

    2017-08-01

    Worldwide consumption of hen eggs results in availability of large amount of discarded egg waste particularly egg shells. In the present study, the waste shells were utilized for the synthesis of highly active heterogeneous calcium oxide (CaO) nanocatalyst to transesterify dry biomass into methyl esters (biodiesel). The CaO nanocatalyst was synthesied by calcination-hydration-dehydration technique and fully characterized by infrared spectroscopy, X-ray powder diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), brunauer-emmett-teller (BET) elemental and thermogravimetric analysis. TEM image showed that the nano catalyst had spherical shape with average particle size of 75 nm. BET analysis indicated that the catalyst specific surface area was 16.4 m 2  g -1 with average pore diameter of 5.07 nm. The effect of nano CaO catalyst was investigated by direct transesterification of dry biomass into biodiesel along with other reaction parameters such as catalyst ratio, reaction time and stirring rate. The impact of the transesterification reaction parameters and microalgal biodiesel yield were analyzed by response surface methodology based on a full factorial, central composite design. The significance of the predicted mode was verified and 86.41% microalgal biodiesel yield was reported at optimal parameter conditions 1.7% (w/w), catalyst ratio, 3.6 h reaction time and stirring rate of 140.6 rpm. The biodiesel conversion was determined by 1 H nuclear magnetic resonance spectroscopy (NMR). The fuel properties of prepared biodiesel were found to be highly comply with the biodiesel standard ASTMD6751 and EN14214. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Surface and adsorptive properties of Moringa oleifera bark for removal of V(V) from aqueous solutions.

    Science.gov (United States)

    Mnisi, Robert Londi; Ndibewu, Peter Papoh

    2017-11-04

    The bark of Moringa oleifera, a cheap and readily available natural biopolymeric resource material, found to significantly reduce coliform load and turbidity in contaminated water is investigated in this paper. Its surface and adsorptive properties are investigated to explore its adsorptive potential in removing V(V) from aqueous solutions. Surface properties were investigated using FTIR, HRSEM/EDS, IC, and BET-N 2 adsorption techniques. Adsorptive properties were investigated by optimizing adsorption parameters such as pH, temperature, initial metal concentration, and adsorbent dosage, using V(V) as an adsorbate. The adsorption-desorption isotherms are typical of type II with a H3 hysteresis loop and is characteristic of a largely macroporous material. Bottle ink pores are observed, which can provide good accessibility of the active sites, even though the internal BET surface area is typically low (1.79 g/m 2 ). Solution pH significantly influences the adsorptive potential of the material. The low surface area negatively impacts on the adsorption capacity, but is compensated for by the exchangeable anions (Cl - , F - , PO 4 3- , NO 3 - , and SO 4 2- ) and cations (Ca 2+ , K + , Mg 2+ , and Al 3+ ) at the surface and the accessibility of the active sites. Adsorption isotherm modeling show that the surface is largely heterogeneous with complex multiple sites and adsorption is not limited to monolayer.

  7. T-bet and Eomes Are Differentially Linked to the Exhausted Phenotype of CD8+T Cells in HIV Infection

    DEFF Research Database (Denmark)

    Buggert, Marcus; Tauriainen, Johanna; Yamamoto, Takuya

    2014-01-01

    CD8+ T cell exhaustion represents a major hallmark of chronic HIV infection. Two key transcription factors governing CD8+ T cell differentiation, T-bet and Eomesodermin (Eomes), have previously been shown in mice to differentially regulate T cell exhaustion in part through direct modulation of PD...

  8. Ezh2 regulates transcriptional and post-translational expression of T-bet and promotes Th1 cell responses mediating aplastic anemia in mice1

    Science.gov (United States)

    Tong, Qing; He, Shan; Xie, Fang; Mochizuki, Kazuhiro; Liu, Yongnian; Mochizuki, Izumi; Meng, Lijun; Sun, Hongxing; Zhang, Yanyun; Guo, Yajun; Hexner, Elizabeth; Zhang, Yi

    2014-01-01

    Acquired aplastic anemia (AA) is a potentially fatal bone marrow (BM) failure syndrome. IFN-γ-producing T helper (Th)1 CD4+ T cells mediate the immune destruction of hematopoietic cells, and are central to the pathogenesis. However, the molecular events that control the development of BM-destructive Th1 cells remain largely unknown. Ezh2 is a chromatin-modifying enzyme that regulates multiple cellular processes primarily by silencing gene expression. We recently reported that Ezh2 is crucial for inflammatory T cell responses after allogeneic BM transplantation. To elucidate whether Ezh2 mediates pathogenic Th1 responses in AA and the mechanism of Ezh2 action in regulating Th1 cells, we studied the effects of Ezh2 inhibition in CD4+ T cells using a mouse model of human AA. Conditionally deleting Ezh2 in mature T cells dramatically reduced the production of BM-destructive Th1 cells in vivo, decreased BM-infiltrating Th1 cells, and rescued mice from BM failure. Ezh2 inhibition resulted in significant decrease in the expression of Tbx21 and Stat4 (which encode transcription factors T-bet and STAT4, respectively). Introduction of T-bet but not STAT4 into Ezh2-deficient T cells fully rescued their differentiation into Th1 cells mediating AA. Ezh2 bound to the Tbx21 promoter in Th1 cells, and directly activated Tbx21 transcription. Unexpectedly, Ezh2 was also required to prevent proteasome-mediated degradation of T-bet protein in Th1 cells. Our results identify T-bet as the transcriptional and post-translational Ezh2 target that acts together to generate BM-destructive Th1 cells, and highlight the therapeutic potential of Ezh2 inhibition in reducing AA and other autoimmune diseases. PMID:24760151

  9. Corn stalks char from fast pyrolysis as precursor material for preparation of activated carbon in fluidized bed reactor.

    Science.gov (United States)

    Wang, Zhiqi; Wu, Jingli; He, Tao; Wu, Jinhu

    2014-09-01

    Corn stalks char from fast pyrolysis was activated by physical and chemical activation process in a fluidized bed reactor. The structure and morphology of the carbons were characterized by N2 adsorption and SEM. Effects of activation time and activation agents on the structure of activation carbon were investigated. The physically activated carbons with CO2 have BET specific surface area up to 880 m(2)/g, and exhibit microporous structure. The chemically activated carbons with H3PO4 have BET specific surface area up to 600 m(2)/g, and exhibit mesoporous structure. The surface morphology shows that physically activated carbons exhibit fibrous like structure in nature with long ridges, resembling parallel lines. Whereas chemically activated carbons have cross-interconnected smooth open pores without the fibrous like structure. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Preparation and recognition of surface molecularly imprinted core-shell microbeads for protein in aqueous solutions

    International Nuclear Information System (INIS)

    Lu Yan; Yan Changling; Gao Shuyan

    2009-01-01

    In this paper, a surface molecular imprinting technique was reported for preparing core-shell microbeads of protein imprinting, and bovine hemoglobin or bovine serum albumin were used as model proteins for studying the imprinted core-shell microbeads. 3-Aminophenylboronic acid (APBA) was polymerized onto the surface of polystyrene microbead in the presence of the protein templates to create protein-imprinted core-shell microbeads. The various samples were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) methods. The effect of pH on rebinding of the template hemoglobin, the specific binding and selective recognition were studied for the imprinted microbeads. The results show that the bovine hemoglobin-imprinted core-shell microbeads were successfully created. The shell was a sort of imprinted thin films with porous structure and larger surface areas. The imprinted microbeads have good selectivity for templates and high stability. Due to the recognition sites locating at or closing to the surface, these imprinted microbeads have good property of mass-transport. Unfortunately, the imprint technology was not successfully applied to imprinting bovine serum albumin (BSA).

  11. Preparation and recognition of surface molecularly imprinted core-shell microbeads for protein in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Lu Yan, E-mail: yanlu2001@sohu.com [College of Chemistry and Environmental Science, Henan Normal University, 46 Jlanshe Road, Xinxiang 453007 (China); Yan Changling; Gao Shuyan [College of Chemistry and Environmental Science, Henan Normal University, 46 Jlanshe Road, Xinxiang 453007 (China)

    2009-04-01

    In this paper, a surface molecular imprinting technique was reported for preparing core-shell microbeads of protein imprinting, and bovine hemoglobin or bovine serum albumin were used as model proteins for studying the imprinted core-shell microbeads. 3-Aminophenylboronic acid (APBA) was polymerized onto the surface of polystyrene microbead in the presence of the protein templates to create protein-imprinted core-shell microbeads. The various samples were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) methods. The effect of pH on rebinding of the template hemoglobin, the specific binding and selective recognition were studied for the imprinted microbeads. The results show that the bovine hemoglobin-imprinted core-shell microbeads were successfully created. The shell was a sort of imprinted thin films with porous structure and larger surface areas. The imprinted microbeads have good selectivity for templates and high stability. Due to the recognition sites locating at or closing to the surface, these imprinted microbeads have good property of mass-transport. Unfortunately, the imprint technology was not successfully applied to imprinting bovine serum albumin (BSA).

  12. Microwave based oxidation process for recycling the off-specification (U,Pu)O{sub 2} fuel pellets

    Energy Technology Data Exchange (ETDEWEB)

    Singh, G., E-mail: gitendars@barctara.gov.in [Advanced Fuel Fabrication Facility (AFFF), Bhabha Atomic Research Centre, Tarapur, 401 502 (India); Khot, P.M. [Advanced Fuel Fabrication Facility (AFFF), Bhabha Atomic Research Centre, Tarapur, 401 502 (India); Kumar, Pradeep [Integrated Fuel Fabrication Facility (IFFF), Bhabha Atomic Research Centre, Mumbai, 400 085 (India); Bhatt, R.B.; Behere, P.G.; Afzal, Mohd [Advanced Fuel Fabrication Facility (AFFF), Bhabha Atomic Research Centre, Tarapur, 401 502 (India)

    2017-02-15

    This paper reports development of a process named MicroWave Direct Oxidation (MWDO) for recycling the off-specification (U,Pu)O{sub 2} mixed oxide (MOX) fuel pellets generated during fabrication of typical fast reactor fuels. MWDO is a two-stage, single-cycle process based on oxidative pulverisation of pellets using 2450 MHz microwave. The powder sinterability was evaluated by bulk density and BET specific surface area. The oxidised powders were analyzed for phases using XRD and stoichiometry by thermogravimetry. The sinterability was significantly enhanced by carrying out oxidation in higher oxygen partial pressure and by subjecting MOX to multiple micronisation-oxidation cycles. After three cycles, the recycled powder from (U,28%Pu)O{sub 2} resulted surface area >3 m{sup 2}/g and 100% re-used for MOX fabrication. The flow sheet was developed for maximum utilization of recycled powder describable by a parameter called Scrap Recycling Ratio (SRR). The process demonstrates smaller processing cycle, better powder properties and higher oxidative pulverisation over conventional method. - Highlights: • A process for recycling the off-specification (U,Pu)O{sub 2} sintered fuel pellets of fast reactors was demonstrated. • The method is a two-stage, single cycle process based on oxidative pulverization of MOX pellets using 2450 MHz microwave. • The process demonstrated utilization of recycled powder with SRR of 1.

  13. MgO-templated nitrogen-containing carbons derived from different organic compounds for capacitor electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Konno, Hidetaka; Onishi, Hiroaki; Azumi, Kazuhisa [Laboratory of Advanced Materials Chemistry, Graduate School of Engineering, Hokkaido University, Sapporo 060-8628 (Japan); Yoshizawa, Noriko [Energy Technology Institute, National Institute of Advanced Industrial Science and Technology, Tsukuba 305-8569 (Japan)

    2010-01-15

    Carbons containing nitrogen (C-N composites) were derived from three commercial organic compounds, poly(vinylpyrrolidone) (PVP), polyacrylamide (PAA), and trimethylolmelamine (TMM) using the MgO template method. The C-N composites formed in nitrogen at 700-1000 C had nitrogen content, W{sub N}, of 3-23 mass% and the specific surface area by N{sub 2} adsorption, S{sub BET}, of 60-2000 m{sup 2} g{sup -1} without activation. Generally high nitrogen content of the starting compound led to larger W{sub N}, but W{sub N} was not proportional to the N/C mole ratio in the compounds. The value of S{sub BET} strongly depended on the compound: S{sub BET} (PVP) > S{sub BET} (PAA) >> S{sub BET} (TMM). There was a tendency for W{sub N} to decrease with increasing S{sub BET}. The capacitance measured in 1 mol dm{sup -3} H{sub 2}SO{sub 4} by cyclic voltammetry, C{sub M} in F g{sup -1}, suggested that both W{sub N} and S{sub BET} are influential in gaining large C{sub M}. For the composites with W{sub N} > 5 mass%, the capacitance normalized by S{sub BET}, C{sub A} = C{sub M}/S{sub BET}, was 0.17-0.65 F m{sup -2}, which was larger than the electric double layer capacitance (0.05-0.15 F m{sup -2}), indicating that the pseudo-capacitance contributes significantly to C{sub M}. The value of C{sub A} increased with increasing W{sub N}, but a correlation between C{sub A} and particular nitrogen species on the surface measured by XPS was obscure. It was suggested that the large C{sub A} is not simply explained by redox reactions of the surface functional groups. The composite derived from PAA at 900 C showed 234 F g{sup -1} at 2 mV s{sup -1} and 181 F g{sup -1} at 100 mV s{sup -1} with acceptable yield of the composite. (author)

  14. A task specific uncertainty analysis method for least-squares-based form characterization of ultra-precision freeform surfaces

    International Nuclear Information System (INIS)

    Ren, M J; Cheung, C F; Kong, L B

    2012-01-01

    In the measurement of ultra-precision freeform surfaces, least-squares-based form characterization methods are widely used to evaluate the form error of the measured surfaces. Although many methodologies have been proposed in recent years to improve the efficiency of the characterization process, relatively little research has been conducted on the analysis of associated uncertainty in the characterization results which may result from those characterization methods being used. As a result, this paper presents a task specific uncertainty analysis method with application in the least-squares-based form characterization of ultra-precision freeform surfaces. That is, the associated uncertainty in the form characterization results is estimated when the measured data are extracted from a specific surface with specific sampling strategy. Three factors are considered in this study which include measurement error, surface form error and sample size. The task specific uncertainty analysis method has been evaluated through a series of experiments. The results show that the task specific uncertainty analysis method can effectively estimate the uncertainty of the form characterization results for a specific freeform surface measurement

  15. Surface characterization studies of walnut-shell biochar catalysts for simultaneously removing of organic sulfur from yellow phosphorus tail gas

    Science.gov (United States)

    Song, Xin; Li, Kai; Ning, Ping; Wang, Chi; Sun, Xin; Tang, Lihong; Ruan, Haotian; Han, Shuang

    2017-12-01

    The influences of different preparation conditions for surface characteristics on removing organic sulfur were studied. From BET, XRD, FTIR, DRIFTS, TG/DTA, CO2-TPD results, it can be seen that these preparation conditions had great influences on the pore structure, specific surface area, crystal structure and surface functional groups. The micropore volume, amorphous structure and alkalinity site strength played major roles in desulfurization process. H2S was oxidized by oxygen containing functional groups, such as sbnd COO, sbnd Cdbnd O. H2O molecule could be converted into some groups, such as sbnd CH and Csbnd OH groups, and promoted the hydrolysis reaction. The strong alkalinity site was the key factor for chemical adsorption and hydrolysis. H2O molecule, sbnd CH, Csbnd OH groups promoted the hydrolysis reaction and sbnd COO, sbnd Cdbnd O groups promoted the oxidation of H2S on the surface of WSB. Meanwhile, the main desulfurization process over WSB after carbonization was adsorption and it changed to hydrolysis reaction after activation on the surface of WSB. Furthermore, the reaction mechanism was investigated by DRIFTS measurement according to the change of surface functional groups.

  16. Nickel metal with various morphologies: synthesis and performances for catalytic carbon dioxide reforming with methane.

    Science.gov (United States)

    Teabpinyok, Nopporn; Samingprai, Sutheerawat; Chareonpanich, Metta

    2012-12-01

    In this research, nickel metal of three different morphologies including nanostar, icosahedra, and microsphere structures were synthesized. It was found nanostar nickel revealed the Ni(111) crystallographic plane with particle size in the range of 150-200 nm and BET surface area of 13 m2/g. The icosahedra nickel also showed the Ni(111) crystallographic plane with larger particle size (300-400 nm) and BET surface area of 20 m2/g, whereas microsphere nickel exhibited the relatively large cluster size (approximately 3 microm) and BET surface area (114 m2/g) as a result of an aggregation of Ni(101) nanoplates. The obtained nickel catalysts were tested for the activity in carbon dioxide reforming with methane. Based on the similar specific surface area of catalysts, nanostar nickel showed the highest carbon dioxide and methane conversions due to its crystallographic structure. At 700 degrees C, nanostar nickel catalyst exhibited the highest carbon dioxide and methane conversions of 17.6 and 10.5 times higher than those of microsphere nickel catalyst, respectively.

  17. Bet hedging in a warming ocean: predictability of maternal environment shapes offspring size variation in marine sticklebacks.

    Science.gov (United States)

    Shama, Lisa N S

    2015-12-01

    Bet hedging at reproduction is expected to evolve when mothers are exposed to unpredictable cues for future environmental conditions, whereas transgenerational plasticity (TGP) should be favoured when cues reliably predict the environment offspring will experience. Since climate predictions forecast an increase in both temperature and climate variability, both TGP and bet hedging are likely to become important strategies to mediate climate change effects. Here, the potential to produce variably sized offspring in both warming and unpredictable environments was tested by investigating whether stickleback (Gasterosteus aculeatus) mothers adjusted mean offspring size and within-clutch variation in offspring size in response to experimental manipulation of maternal thermal environment and predictability (alternating between ambient and elevated water temperatures). Reproductive output traits of F1 females were influenced by both temperature and environmental predictability. Mothers that developed at ambient temperature (17 °C) produced larger, but fewer eggs than mothers that developed at elevated temperature (21 °C), implying selection for different-sized offspring in different environments. Mothers in unpredictable environments had smaller mean egg sizes and tended to have greater within-female egg size variability, especially at 21 °C, suggesting that mothers may have dynamically modified the variance in offspring size to spread the risk of incorrectly predicting future environmental conditions. Both TGP and diversification influenced F2 offspring body size. F2 offspring reared at 21 °C had larger mean body sizes if their mother developed at 21 °C, but this TGP benefit was not present for offspring of 17 °C mothers reared at 17 °C, indicating that maternal TGP will be highly relevant for ocean warming scenarios in this system. Offspring of variable environment mothers were smaller but more variable in size than offspring from constant environment

  18. Preparation, Surface and Pore Structure of High Surface Area Activated Carbon Fibers from Bamboo by Steam Activation

    Directory of Open Access Journals (Sweden)

    Xiaojun Ma

    2014-06-01

    Full Text Available High surface area activated carbon fibers (ACF have been prepared from bamboo by steam activation after liquefaction and curing. The influences of activation temperature on the microstructure, surface area and porosity were investigated. The results showed that ACF from bamboo at 850 °C have the maximum iodine and methylene blue adsorption values. Aside from the graphitic carbon, phenolic and carbonyl groups were the predominant functions on the surface of activated carbon fiber from bamboo. The prepared ACF from bamboo were found to be mainly type I of isotherm, but the mesoporosity presented an increasing trend after 700 °C. The surface area and micropore volume of samples, which were determined by application of the Brunauer-Emmett-Teller (BET and t-plot methods, were as high as 2024 m2/g and 0.569 cm3/g, respectively. It was also found that the higher activation temperature produced the more ordered microcrystalline structure of ACF from bamboo.

  19. Progress in the specification of optical instruments for the measurement of surface form and texture

    Science.gov (United States)

    de Groot, Peter J.

    2014-05-01

    Specifications for confocal microscopes, optical interferometers and other methods of measuring areal surface topography can be confusing and misleading. The emerging ISO 25178 standards, together with the established international vocabulary of metrology, provide a foundation for improved specifications for 3D surface metrology instrumentation. The approach in this paper links instrument specifications to metrological characteristics that can influence a measurement, using consistent definitions of terms, and reference to verification procedures.

  20. Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

    Directory of Open Access Journals (Sweden)

    Zhang Dongkun

    2015-04-01

    Full Text Available Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication (MQL, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm3, respectively. The specific grinding energy significantly decreased to 32.7 J/mm3 in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%, respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%, and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS2, carbon nanotube (CNT, and ZrO2 nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS2 nanoparticle was only 32.7 J/mm3, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS2 nanoparticle, which indicated its remarkable lubrication effects. Furthermore, the role of MoS2 particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS2 volume concentrations of 1%, 2%, and 3% were used. Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS2 nanoparticle volume concentration increased. Satisfactory grinding surface lubrication effects were obtained with 2% MoS2 nanoparticle volume concentration.

  1. Acid leaching of natural chrysotile asbestos to mesoporous silica fibers

    Science.gov (United States)

    Maletaškić, Jelena; Stanković, Nadežda; Daneu, Nina; Babić, Biljana; Stoiljković, Milovan; Yoshida, Katsumi; Matović, Branko

    2018-04-01

    Nanofibrous silica with a high surface area was produced from chrysotile by the acid-leaching method. Natural mineral chrysotile asbestos from Stragari, Korlace in Serbia was used as the starting material. The fibers were modified by chemical treatment with 1 M HCl and the mineral dissolution was monitored by transmission electron microscopy, X-ray powder diffraction, inductively coupled plasma spectrometry and low-temperature nitrogen adsorption techniques to highlight the effects of the leaching process. The results showed that the applied concentration of acid solution and processing time of 4 h were sufficient to effectively remove the magnesium hydroxide layer and transform the crystal structure of the hazardous starting chrysotile to porous SiO2 nanofibers. With prolonged acid leaching, the specific surface area, S BET, calculated by BET equation, was increased from 147 up to 435 m2 g- 1, with micropores representing a significant part of the specific surface.

  2. Citrate precursor synthesis, characterization and dielectric properties of Ba1-xSrxZrO3 (0 ≤ x ≤1)

    International Nuclear Information System (INIS)

    Ubaidullah, Mohd; Ahmad, Tokeer; Al-Hartomy, Omar A.

    2012-01-01

    Barium Strontium Zirconate (BSZ) nanoparticles of the general formula Ba 1-x Sr x ZrO 3 over the composition range of (x= 0.0, 0.05, 0.10, 0.15, 0.20, 0.25, 0.50, 0.75 and 1.0) have been successfully synthesized by simple and most elegant method known as Polymeric citrate precursor route using citric acid and ethylene glycol for the first time. These solid solutions were investigated by means of powder X-ray diffraction (PXRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and BET surface area studies. XRD studies revealed the monophasic nature of the powders after heating the precursor at 1000 ℃. The particle size obtained from TEM studies were found to be in the range of 13.8-40 nm. Specific surface area of the solid solutions comes out to be in the range of 49 to 94 m 2 g -1 . The average particle size of these nanoparticles could also be calculated using the equation: D BET = 6000/(ρ.S w ), where the symbols D BET , ρ, S w stand for average diameter of the spherical particle, theoretical density, and specific surface area of the sample in m 2 /g respectively

  3. Specificity for field enumeration of Escherichia coli in tropical surface waters

    DEFF Research Database (Denmark)

    Jensen, Peter Kjær Mackie; Aalbaek, B; Aslam, R

    2001-01-01

    In remote rural areas in developing countries, bacteriological monitoring often depends on the use of commercial field media. This paper evaluates a commercial field medium used for the enumeration of Escherichia coli in different surface waters under primitive field conditions in rural Pakistan....... In order to verify the field kit, 117 presumptive E. coli isolates have been tested, finding a specificity of only 40%. By excluding some strains based on colony colours, the calculated specificity could be increased to 65%. Thus, it is suggested that prior to use in a tropical environment, the specificity...... of any commercial medium used should be tested with representative tropical isolates, in order to increase the specificity....

  4. Optimisation of bitumen emulsion properties for ballast stabilisation; Optimización de las propiedades de emulsión de betún para la estabilización de balasto.

    Energy Technology Data Exchange (ETDEWEB)

    D’Angelo, G.; Lo Presti, D.; Thom, N.

    2017-07-01

    Ballasted track, while providing economical and practical advantages, is associated with high costs and material consumption due to frequent maintenance. More sustainable alternatives to conventional ballasted trackbeds should therefore aim at extending its durability, particularly considering ongoing increases in traffic speed and loads. In this regard, the authors have investigated a solution consisting of bitumen stabilised ballast (BSB), designed to be used for new trackbeds as well as in reinforcing existing ones. This study presents the idea behind the technology and then focuses on a specific part of its development: the optimisation of bitumen emulsion properties and dosage in relation to ballast field conditions. Results showed that overall bitumen stabilisation improved ballast resistance to permanent deformation by enhancing stiffness and damping properties. Scenarios with higher dosage of bitumen emulsion, higher viscosity, quicker setting behaviour, and harder base bitumen seem to represent the most desirable conditions to achieve enhanced in-field performance. [Spanish] El balasto proporciona ventajas económicas y prácticas, sin embargo se asocia con altos costos y consumo de materiales. Las alternativas más sostenibles deben tener como objetivo extender la durabilidad del balasto, sobre todo teniendo en cuenta los actuales incrementos en la velocidad y las cargas del tráfico. Los autores presentan una solución que consiste en estabilizar el balasto con betún. Este estudio describe la tecnología y se centra en la optimización de las propiedades de la emulsión bituminosa y su dosis en función de las condiciones del balasto. Los resultados muestran que la stabilización con betún mejora la resistencia a la deformación permanente mediante la modificación de la rigidez y las propiedades de amortiguación. Pruebas con mayor dosis de emulsión bituminosa, mayor viscosidad, fraguado rápido y betún base más duro, representan las condiciones m

  5. ITO nanoparticles reused from ITO scraps and their applications to sputtering target for transparent conductive electrode layer

    OpenAIRE

    Hong, Sung-Jei; Song, Sang-Hyun; Kim, Byeong Jun; Lee, Jae-Yong; Kim, Young-Sung

    2017-01-01

    In this study, ITO nanoparticles (ITO-NPs) were reused from ITO target scraps to synthesize low cost ITO-NPs and to apply to make sputtering target for transparent conductive electrodes (TCEs). By controlling heat-treatment temperature as 980??C, we achieved reused ITO-NPs having Brunauer, Emmett and Teller specific surface area (BET SSA) and average particle size 8.05?m2/g and 103.8?nm, respectively. The BET SSA decreases along with increasing heat-treatment temperature. The ITO-NPs were gro...

  6. Ions-induced nanostructuration: effect of specific ionic adsorption on hydrophobic polymer surfaces.

    Science.gov (United States)

    Siretanu, Igor; Chapel, Jean-Paul; Bastos-González, Delfi; Drummond, Carlos

    2013-06-06

    The effect of surface charges on the ionic distribution in close proximity to an interface has been extensively studied. On the contrary, the influence of ions (from dissolved salts) on deformable interfaces has been barely investigated. Ions can adsorb from aqueous solutions on hydrophobic surfaces, generating forces that can induce long-lasting deformation of glassy polymer films, a process called ion-induced polymer nanostructuration, IPN. We have found that this process is ion-specific; larger surface modifications are observed in the presence of water ions and hydrophobic and amphiphilic ions. Surface structuration is also observed in the presence of certain salts of lithium. We have used streaming potential and atomic force microscopy to study the effect of dissolved ions on the surface properties of polystyrene films, finding a good correlation between ionic adsorption and IPN. Our results also suggest that the presence of strongly hydrated lithium promotes the interaction of anions with polystyrene surfaces and more generally with hydrophobic polymer surfaces, triggering then the IPN process.

  7. Nitrogen-doped hierarchical lamellar porous carbon synthesized from the fish scale as support material for platinum nanoparticle electrocatalyst toward the oxygen reduction reaction.

    Science.gov (United States)

    Liu, Haijing; Cao, Yinliang; Wang, Feng; Huang, Yaqin

    2014-01-22

    Novel hierarchical lamellar porous carbon (HLPC) with high BET specific surface area of 2730 m(2) g(-1) and doped by nitrogen atoms has been synthesized from the fish scale without any post-synthesis treatment, and applied to support the platinum (Pt) nanoparticle (NP) catalysts (Pt/HLPC). The Pt NPs could be highly dispersed on the porous surface of HLPC with a narrow size distribution centered at ca. 2.0 nm. The results of the electrochemical analysis reveal that the electrochemical active surface area (ECSA) of Pt/HLPC is larger than the Pt NP electrocatalyst supported on the carbon black (Pt/Vulcan XC-72). Compared with the Pt/Vulcan XC-72, the Pt/HLPC exhibits larger current density, lower overpotential, and enhanced catalytic activity toward the oxygen reduction reaction (ORR) through the direct four-electron pathway. The improved catalytic activity is mainly attributed to the high BET specific surface area, hierarchical porous structures and the nitrogen-doped surface property of HLPC, indicating the superiority of HLPC as a promising support material for the ORR electrocatalysts.

  8. Characterization of pigment-leached antifouling coatings using BET surface area measurements and mercury porosimetry

    DEFF Research Database (Denmark)

    Kiil, Søren; Dam-Johansen, Kim

    2007-01-01

    of antifouling coating behaviour because the active binder surface area and porosity of the leached layer are substantially increased. A similar effect was not observed for a coating with a mixture of ZnO and TiO2 pigments. The two experimental methods are expected to be useful for practical analysis of leaching...

  9. Towards real-time eruption forecasting in the Auckland Volcanic Field: application of BET_EF during the New Zealand National Disaster Exercise `Ruaumoko'

    Science.gov (United States)

    Lindsay, Jan; Marzocchi, Warner; Jolly, Gill; Constantinescu, Robert; Selva, Jacopo; Sandri, Laura

    2010-03-01

    The Auckland Volcanic Field (AVF) is a young basaltic field that lies beneath the urban area of Auckland, New Zealand’s largest city. Over the past 250,000 years the AVF has produced at least 49 basaltic centers; the last eruption was only 600 years ago. In recognition of the high risk associated with a possible future eruption in Auckland, the New Zealand government ran Exercise Ruaumoko in March 2008, a test of New Zealand’s nation-wide preparedness for responding to a major disaster resulting from a volcanic eruption in Auckland City. The exercise scenario was developed in secret, and covered the period of precursory activity up until the eruption. During Exercise Ruaumoko we adapted a recently developed statistical code for eruption forecasting, namely BET_EF (Bayesian Event Tree for Eruption Forecasting), to independently track the unrest evolution and to forecast the most likely onset time, location and style of the initial phase of the simulated eruption. The code was set up before the start of the exercise by entering reliable information on the past history of the AVF as well as the monitoring signals expected in the event of magmatic unrest and an impending eruption. The average probabilities calculated by BET_EF during Exercise Ruaumoko corresponded well to the probabilities subjectively (and independently) estimated by the advising scientists (differences of few percentage units), and provided a sound forecast of the timing (before the event, the eruption probability reached 90%) and location of the eruption. This application of BET_EF to a volcanic field that has experienced no historical activity and for which otherwise limited prior information is available shows its versatility and potential usefulness as a tool to aid decision-making for a wide range of volcano types. Our near real-time application of BET_EF during Exercise Ruaumoko highlighted its potential to clarify and possibly optimize decision-making procedures in a future AVF eruption

  10. A Tempest in A Ladle: The Debate about the Roles of General and Specific Abilities in Predicting Important Outcomes

    OpenAIRE

    Wendy Johnson

    2018-01-01

    The debate about the roles of general and specific abilities in predicting important outcomes is a tempest in a ladle because we cannot measure abilities without also measuring skills. Skills always develop through exposure, are specific rather than general, and are executed using different strategies by different people, thus tapping into varied specific abilities. Relative predictive validities of measurement formats depend on the purpose: the more general and long-term the purpose, the bet...

  11. Crystallization of glass-forming liquids: Specific surface energy

    International Nuclear Information System (INIS)

    Schmelzer, Jürn W. P.; Abyzov, Alexander S.

    2016-01-01

    A generalization of the Stefan-Skapski-Turnbull relation for the melt-crystal specific interfacial energy is developed in terms of the generalized Gibbs approach extending its standard formulation to thermodynamic non-equilibrium states. With respect to crystal nucleation, this relation is required in order to determine the parameters of the critical crystal clusters being a prerequisite for the computation of the work of critical cluster formation. As one of its consequences, a relation for the dependence of the specific surface energy of critical clusters on temperature and pressure is derived applicable for small and moderate deviations from liquid-crystal macroscopic equilibrium states. Employing the Stefan-Skapski-Turnbull relation, general expressions for the size and the work of formation of critical crystal clusters are formulated. The resulting expressions are much more complex as compared to the respective relations obtained via the classical Gibbs theory. Latter relations are retained as limiting cases of these more general expressions for moderate undercoolings. By this reason, the formulated, here, general relations for the specification of the critical cluster size and the work of critical cluster formation give a key for an appropriate interpretation of a variety of crystallization phenomena occurring at large undercoolings which cannot be understood in terms of the Gibbs’ classical treatment.

  12. Specific surface area of overlapping spheres in the presence of obstructions.

    Science.gov (United States)

    Jenkins, D R

    2013-02-21

    This study considers the random placement of uniform sized spheres, which may overlap, in the presence of another set of randomly placed (hard) spheres, which do not overlap. The overlapping spheres do not intersect the hard spheres. It is shown that the specific surface area of the collection of overlapping spheres is affected by the hard spheres, such that there is a minimum in the specific surface area as a function of the relative size of the two sets of spheres. The occurrence of the minimum is explained in terms of the break-up of pore connectivity. The configuration can be considered to be a simple model of the structure of a porous composite material. In particular, the overlapping particles represent voids while the hard particles represent fillers. Example materials are pervious concrete, metallurgical coke, ice cream, and polymer composites. We also show how the material properties of such composites are affected by the void structure.

  13. Structure-Based Discovery of 4-(6-Methoxy-2-methyl-4-(quinolin-4-yl)-9 H -pyrimido[4,5- b ]indol-7-yl)-3,5-dimethylisoxazole (CD161) as a Potent and Orally Bioavailable BET Bromodomain Inhibitor

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Yujun; Bai, Longchuan; Liu, Liu; McEachern, Donna; Stuckey, Jeanne A.; Meagher, Jennifer L.; Yang, Chao-Yie; Ran, Xu; Zhou, Bing; Hu, Yang; Li, Xiaoqin; Wen, Bo; Zhao, Ting; Li, Siwei; Sun, Duxin; Wang, Shaomeng (Michigan)

    2017-03-24

    We have designed and synthesized 9H-pyrimido[4,5-b]indole-containing compounds to obtain potent and orally bioavailable BET inhibitors. By incorporation of an indole or a quinoline moiety to the 9H-pyrimido[4,5-b]indole core, we identified a series of small molecules showing high binding affinities to BET proteins and low nanomolar potencies in inhibition of cell growth in acute leukemia cell lines. One such compound, 4-(6-methoxy-2-methyl-4-(quinolin-4-yl)-9H-pyrimido[4,5-b]indol-7-yl)-3,5-dimethylisoxazole (31) has excellent microsomal stability and good oral pharmacokinetics in rats and mice. Orally administered, 31 achieves significant antitumor activity in the MV4;11 leukemia and MDA-MB-231 triple-negative breast cancer xenograft models in mice. Determination of the cocrystal structure of 31 with BRD4 BD2 provides a structural basis for its high binding affinity to BET proteins. Testing its binding affinities against other bromodomain-containing proteins shows that 31 is a highly selective inhibitor of BET proteins. Our data show that 31 is a potent, selective, and orally active BET inhibitor.

  14. Analysis of the phonon surface specific heat using Green function techniques

    International Nuclear Information System (INIS)

    Silva Carrico, A. da; Albuquerque, E.L. de

    1981-01-01

    Green functions are derived for the displacement associated with acoustic vibrations in isotropic elastic media and used to evaluate the surface specific heat in the harmonic approximation. Only the low-temperature limit case is considered since, provided K sub(B) T/h is very small, the dispersion relation for the three acoustic branches can be replaced by its long-wavelenght form. The contributions of surface elastic waves of the Rayleigh and Love types are pointed out and their features discussed. The nature of the result and their relations to previous work in this field is also presented and discussed. (Author) [pt

  15. Analysis of the phonon surface specific heat using Green function techniques

    International Nuclear Information System (INIS)

    Carrico, A.S.; Albuquerque, E.L.

    1980-01-01

    Green functions are derived for the displacement associated with acoustic vibrations in isotropic elastic media and used to evaluate the surface specific heat in the harmonic approximation. We consider only the low-temperature limit case since, provided K B 1/h is very samll, we can replace the dispersion relation for the three acoustic branches by its long-wavelenghts form. The contributions of surface elastic waves ot the Rayleigh and Love types are pointed out and their features discussed. The nature of the result and their relations to previous work in this field is also presented and discussed. (author) [pt

  16. Stable T-bet+GATA-3+ Th1/Th2 Hybrid Cells Arise In Vivo, Can Develop Directly from Naive Precursors, and Limit Immunopathologic Inflammation

    Science.gov (United States)

    Peine, Michael; Fröhlich, Anja; Hegazy, Ahmed N.; Kühl, Anja A.; Grevelding, Christoph G.; Höfer, Thomas; Hartmann, Susanne; Löhning, Max

    2013-01-01

    Differentiated T helper (Th) cell lineages are thought to emerge from alternative cell fate decisions. However, recent studies indicated that differentiated Th cells can adopt mixed phenotypes during secondary immunological challenges. Here we show that natural primary immune responses against parasites generate bifunctional Th1 and Th2 hybrid cells that co-express the lineage-specifying transcription factors T-bet and GATA-3 and co-produce Th1 and Th2 cytokines. The integration of Th1-promoting interferon (IFN)-γ and interleukin (IL)-12 signals together with Th2-favoring IL-4 signals commits naive Th cells directly and homogeneously to the hybrid Th1/2 phenotype. Specifically, IFN-γ signals are essential for T-bet+GATA-3+ cells to develop in vitro and in vivo by breaking the dominance of IL-4 over IL-12 signals. The hybrid Th1/2 phenotype is stably maintained in memory cells in vivo for months. It resists reprogramming into classic Th1 or Th2 cells by Th1- or Th2-promoting stimuli, which rather induce quantitative modulations of the combined Th1 and Th2 programs without abolishing either. The hybrid phenotype is associated with intermediate manifestations of both Th1 and Th2 cell properties. Consistently, hybrid Th1/2 cells support inflammatory type-1 and type-2 immune responses but cause less immunopathology than Th1 and Th2 cells, respectively. Thus, we propose the self-limitation of effector T cells based on the stable cell-intrinsic balance of two opposing differentiation programs as a novel concept of how the immune system can prevent excessive inflammation. PMID:23976880

  17. Stable T-bet(+GATA-3(+ Th1/Th2 hybrid cells arise in vivo, can develop directly from naive precursors, and limit immunopathologic inflammation.

    Directory of Open Access Journals (Sweden)

    Michael Peine

    Full Text Available Differentiated T helper (Th cell lineages are thought to emerge from alternative cell fate decisions. However, recent studies indicated that differentiated Th cells can adopt mixed phenotypes during secondary immunological challenges. Here we show that natural primary immune responses against parasites generate bifunctional Th1 and Th2 hybrid cells that co-express the lineage-specifying transcription factors T-bet and GATA-3 and co-produce Th1 and Th2 cytokines. The integration of Th1-promoting interferon (IFN-γ and interleukin (IL-12 signals together with Th2-favoring IL-4 signals commits naive Th cells directly and homogeneously to the hybrid Th1/2 phenotype. Specifically, IFN-γ signals are essential for T-bet(+GATA-3(+ cells to develop in vitro and in vivo by breaking the dominance of IL-4 over IL-12 signals. The hybrid Th1/2 phenotype is stably maintained in memory cells in vivo for months. It resists reprogramming into classic Th1 or Th2 cells by Th1- or Th2-promoting stimuli, which rather induce quantitative modulations of the combined Th1 and Th2 programs without abolishing either. The hybrid phenotype is associated with intermediate manifestations of both Th1 and Th2 cell properties. Consistently, hybrid Th1/2 cells support inflammatory type-1 and type-2 immune responses but cause less immunopathology than Th1 and Th2 cells, respectively. Thus, we propose the self-limitation of effector T cells based on the stable cell-intrinsic balance of two opposing differentiation programs as a novel concept of how the immune system can prevent excessive inflammation.

  18. Surface Improvement of Halloysite Nanotubes

    Directory of Open Access Journals (Sweden)

    Tayser Sumer Gaaz

    2017-03-01

    Full Text Available A novel development on halloysite-polyvinyl alcohol (HNTs-PVA nanocomposites has been conducted using malonic acid (MA by crosslinking PVA and HNTs. PVA-MA crosslinking produces smooth surfaces, which play an important role in enhancing the properties of HNTs-PVA nanocomposite. The crystallographic structures of crosslinked HNTs-PVA show almost no change as depicted by the X-ray diffraction (XRD-2θ-peak, suggesting that MA has no or little influence on the crystallographic structure of the HNTs-PVA. Images taken by field emission scanning electron microscope (FESEM suggest possible effects of MA on the morphology and internal features of HNTs-PVA by reducing the agglomeration of HNTs, which is considered a decisive step in improving the surface qualities of HNTs. Investigating the samples using the Brunauer–Emmelt–Teller (BET technique showed that the surface area was increased by about 10 times, reaching the second highest recorded results compared to the HNTs, which could be considered a breakthrough step in enhancing the properties of HNTs-PVA due to MA crosslinking.

  19. Characterizing the sorption of polybrominated diphenyl ethers (PBDEs) to cotton and polyester fabrics under controlled conditions

    Energy Technology Data Exchange (ETDEWEB)

    Saini, Amandeep [Department of Physical and Environmental Sciences, University of Toronto Scarborough, 1265 Military trail, Toronto, ON M1C 1A4 (Canada); Rauert, Cassandra [School of Geography, Earth and Environmental Sciences, University of Birmingham, Birmingham B15 2TT (United Kingdom); Simpson, Myrna J. [Department of Physical and Environmental Sciences, University of Toronto Scarborough, 1265 Military trail, Toronto, ON M1C 1A4 (Canada); Harrad, Stuart [School of Geography, Earth and Environmental Sciences, University of Birmingham, Birmingham B15 2TT (United Kingdom); Diamond, Miriam L., E-mail: miriam.diamond@utoronto.ca [Department of Earth Sciences, 22 Russell Street, University of Toronto, Toronto, ON M5S 3B1 (Canada); Department of Physical and Environmental Sciences, University of Toronto Scarborough, 1265 Military trail, Toronto, ON M1C 1A4 (Canada)

    2016-09-01

    Cotton and polyester, physically and chemically different fabrics, were characterized for sorption of gas-phase polybrominated diphenyl ethers (PBDEs). Scanning electron microscopic (SEM) images and BET specific surface area (BET-SSA) analysis showed cotton's high microsurface area; NMR analysis showed richness of hexose- and aromatic-carbon in cotton and polyester, respectively. Cotton and polyester sorbed similar concentrations of gas-phase PBDEs in chamber studies, when normalized to planar surface area. However, polyester concentrations were 20–50 times greater than cotton when normalized to BET-SSA, greater than the 10 times difference in BET-SSA. The difference in sorption between cotton and polyester is hypothesized to be due to ‘dilution’ due to cotton's large BET-SSA and/or greater affinity of PBDEs for aromatic-rich polyester. Similar fabric-air area normalized distribution coefficients (K'{sub D}, 10{sup 3} to 10{sup 4} m) for cotton and polyester support air-side controlled uptake under non-equilibrium conditions. K'{sub D} values imply that 1 m{sup 2} of cotton or polyester fabrics would sorb gas-phase PBDEs present in 10{sup 3} to 10{sup 4} m{sup 3} of equivalent air volume at room temperature over one week, assuming similar air flow conditions. Sorption of PBDEs to fabrics has implications for their fate indoors and human exposure. - Highlights: • Sorption of gas-phase PBDEs by cotton and polyester fabrics • Similar sorption to cotton and polyester per unit planar surface area • Greater sorption by polyester/BET-SSA; cotton's dilution or polyester’s affinity • 1 m{sup 2} fabric sorbs PBDEs in 10{sup 3} to 10{sup 4} m{sup 3} of equivalent air volume • Clothing likely a large indoor sink of PBDEs and influence human exposure.

  20. Geochemical signatures of uranium deposits within stream sediment of humid intertropical environment example from Gabon Francevillien deposits

    International Nuclear Information System (INIS)

    Nganzi, C.

    1983-01-01

    In the frame of geochemical prospection of uranium ores, the method based on adsorption is used for interpreting anomalies in classical methods. This study shows the importance of adsorption from specific surface area determined by the B.E.T. method [fr

  1. JCSC_129_03_0397_0404_SI.docx

    Indian Academy of Sciences (India)

    dell

    Material, BET Surface area (m2/g), Specific capacitance (F/g) at 0.2 A/g. Graphene oxide, -, 255. Reduced graphene oxide, -, 14. Non Ac-Sugar, 787, 104. Ac-Sugar, 655, 140. AC-rice husk, 547, 369. AC-jute, 825, 476.

  2. T-bet-dependent NKp46+ innate lymphoid cells regulate the onset of TH17-induced neuroinflammation. | Center for Cancer Research

    Science.gov (United States)

    The process by which self-reactive CD4+ T cells infiltrate the central nervous system (CNS) and trigger neuroinflammation is not fully understood. Lazarevic and colleagues show that NKp46+innate lymphoid cells dependent on the transcription factor T-bet are critical mediators in facilitating the entry of autoreactive CD4+ cells of the TH17 subset of helper T cells into the

  3. Phenol removal onto novel activated carbons made from lignocellulosic precursors: Influence of surface properties

    OpenAIRE

    Valente Nabais, Joao; Gomes, Jose; Suhas, Suhas; Carrott, Peter; Laginhas, Carlos; Roman, Silvia

    2009-01-01

    The adsorption of phenol from dilute aqueous solutions onto new activated carbons (AC) was studied. The novel activated carbon was produced from lignocellulosic (LC) precursors of rapeseed and kenaf. Samples oxidised with nitric acid in liquid phasewere also studied. The results have shown the significant potential of rapeseed and kenaf for the activated carbon production. The activated carbons produced by carbon dioxide activation were mainly microporous with BET apparent surface...

  4. Phospholipase D specific for the phosphatidylinositol anchor of cell-surface proteins is abundant in plasma

    International Nuclear Information System (INIS)

    Low, M.G.; Prasad, A.R.S.

    1988-01-01

    An enzyme activity capable of degrading the glycosyl-phosphatidylinositol membrane anchor of cell-surface proteins has previously been reported in a number of mammalian tissues. The experiments reported here demonstrate that this anchor-degrading activity is also abundant in mammalian plasma. The activity was inhibited by EGTA or 1,10-phenanthroline. It was capable of removing the anchor from alkaline phosphatase, 5'-nucleotidase, and variant surface glycoprotein but had little or no activity toward phosphatidylinositol or phosphatidylcholine. Phosphatidic acid was the only 3 H-labeled product when this enzyme hydrolyzed [ 3 H]myristate-labeled variant surface glycoprotein. It could be distinguished from the Ca 2 =-dependent inositol phospholipid-specific phospholipase C activity in several rat tissues on the basis of its molecular size and its sensitivity to 1,10-phenanthroline. The data therefore suggest that this activity is due to a phospholipase D with specificity for glycosylphosphatidylinositol structures. Although the precise physiological function of this anchor-specific phospholipase D remains to be determined, these findings indicate that it could play an important role in regulating the expression and release of cell-surface proteins in vivo

  5. Adsorption of ibuprofen from aqueous solution on chemically surface-modified activated carbon cloths

    Directory of Open Access Journals (Sweden)

    Hanen Guedidi

    2017-05-01

    Full Text Available This study aims to investigate the performance of an activated carbon cloth for adsorption of ibuprofen. The cloth was oxidized by a NaOCl solution (0.13 mol L−1 or thermally treated under N2 (700 °C for 1 hour. The raw and modified cloths were characterized by N2 adsorption–desorption measurement at 77 K, CO2 adsorption at 273 K, Boehm titrations, pHPZC measurements, X-ray Photoelectron Spectroscopy analysis, and by infrared spectroscopy. The NaOCl treatment increases the acidic sites, mostly creating phenolic and carboxylic groups and decreases both the specific surface area and slightly the micropore volume. However, the thermal treatment at 700 °C under N2 induced a slight increase in the BET specific surface area and yielded to the only increase in the carbonyl group content. Ibuprofen adsorption studies of kinetics and isotherms were carried out at pH = 3 and 7. The adsorption properties were correlated to the cloth porous textures, surface chemistry and pH conditions. The isotherms of adsorption were better reproduced by Langmuir–Freundlich models at 298, 313 and 328 K. The adsorption of ibuprofen on the studied activated carbon cloths at pH 3 was an endothermic process. The pore size distributions of all studied ibuprofen-loaded fabrics were determined by DFT method to investigate the accessible porosity of the adsorbate. Both treatments do not influence the kind of micropores where the adsorption of ibuprofen occurred.

  6. Determination of the surface area and sizes of supported copper nanoparticles through organothiol adsorption—ñhemisorption

    Energy Technology Data Exchange (ETDEWEB)

    Ndolomingo, Matumuene Joe; Meijboom, Reinout, E-mail: rmeijboom@uj.ac.za

    2016-12-30

    Highlights: • Cu on γ-Al{sub 2}O{sub 3} catalysts were prepared and characterized. • The ligand sorption-based technique was used for the determination of specific surface area and particle sizes. • The ligand packing density on Cu nanoparticles was quantified. • A fair agreement was found between the Cu particle sizes obtained from ligand adsorption and TEM methods. • The oxidation of morin by hydrogen peroxide was used to evaluate the catalytic activities of the Cu supported catalysts. - Abstract: The mechanisms involving the nanoparticle surfaces in catalytic reactions are more difficult to elucidate due to the nanoparticle surface unevenness, size distributions, and morphological irregularity. True surface area and particle sizes determination are key aspects of the activity of metal nanoparticle catalysts. Here we report on the organothiol adsorption-based technique for the determination of specific surface area of Cu nanoparticles, and their resultant sizes on γ-Al{sub 2}O{sub 3} supports. Quantification of ligand packing density on copper nanoparticles is also reported. The concentration of the probe ligand, 2-mercaptobenzimidazole (2-MBI) before and after immersion of supported copper catalysts was determined by ultraviolet-visible spectrometry (UV–vis). The amount of ligand adsorbed was found to be proportional to the copper nanoparticles surface area. Atomic absorption spectrometry (AAS), N{sub 2}-physisorption (BET), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA) were used for the characterization of the catalysts. A fair agreement was found between particle sizes obtained from ligand adsorption and TEM methods. The catalytic activity of the copper nanoparticles related to their inherent surface area was evaluated using the model reaction of the oxidation of morin by hydrogen peroxide.

  7. Tuning the relative concentration ratio of bulk defects to surface defects in TiO2 nanocrystals leads to high photocatalytic efficiency.

    Science.gov (United States)

    Kong, Ming; Li, Yuanzhi; Chen, Xiong; Tian, Tingting; Fang, Pengfei; Zheng, Feng; Zhao, Xiujian

    2011-10-19

    TiO(2) nanocrystals with tunable bulk/surface defects were synthesized and characterized with TEM, XRD, BET, positron annihilation, and photocurrent measurements. The effect of defects on photocatalytic activity was studied. It was found for the first time that decreasing the relative concentration ratio of bulk defects to surface defects in TiO(2) nanocrystals could significantly improve the separation efficiency of photogenerated electrons and holes, thus significantly enhancing the photocatalytic efficiency.

  8. Correlation of Gear Surface Fatigue Lives to Lambda Ratio (Specific Film Thickness)

    Science.gov (United States)

    Krantz, Timothy Lewis

    2013-01-01

    The effect of the lubrication regime on gear performance has been recognized, qualitatively, for decades. Often the lubrication regime is characterized by the specific film thickness being the ratio of lubricant film thickness to the composite surface roughness. Three studies done at NASA to investigate gearing pitting life are revisited in this work. All tests were done at a common load. In one study, ground gears were tested using a variety of lubricants that included a range of viscosities, and therefore the gears operated with differing film thicknesses. In a second and third study, the performance of gears with ground teeth and superfinished teeth were assessed. Thicker oil films provided longer lives as did improved surface finish. These datasets were combined into a common dataset using the concept of specific film thickness. This unique dataset of more 258 tests provides gear designers with some qualitative information to make gear design decisions.

  9. [Adsorption of Cu on Core-shell Structured Magnetic Particles: Relationship Between Adsorption Performance and Surface Properties].

    Science.gov (United States)

    Li, Qiu-mei; Chen, Jing; Li, Hai-ning; Zhang, Xiao-lei; Zhang, Gao-sheng

    2015-12-01

    In order to reveal the relationship between the adsorption performance of adsorbents and their compositions, structure, and surface properties, the core-shell structured Fe₃O₄/MnO2 and Fe-Mn/Mn₂2 magnetic particles were systematically characterized using multiple techniques and their Cu adsorption behaviors as well as mechanism were also investigated in details. It was found that both Fe₃O4 and Fe-Mn had spinel structure and no obvious crystalline phase change was observed after coating with MnO₂. The introduction of Mn might improve the affinity between the core and the shell, and therefore enhanced the amount and distribution uniformity of the MnO₂ coated. Consequently, Fe-Mn/MnO₂ exhibited a higher BET specific surface area and a lower isoelectric point. The results of sorption experiments showed that Fe-Mn had a higher maximal Cu adsorption capacity of 33.7 mg · g⁻¹ at pH 5.5, compared with 17.5 mg · g⁻¹ of Fe₃O4. After coating, the maximal adsorption capacity of Fe-Mn/MnO₂ was increased to 58.2 mg · g⁻¹, which was 2.6 times as high as that of Fe₃O₄/MnO₂ and outperformed the majority of magnetic adsorbents reported in literature. In addition, a specific adsorption of Cu occurred at the surface of Fe₃O₄/MnO₂ or Fe-Mn/MnO₂ through the formation of inner-sphere complexes. In conclusion, the adsorption performance of the magnetic particles was positively related to their compositions, structure, and surface properties.

  10. Biotransformation of Momordica charantia fresh juice by Lactobacillus plantarum BET003 and its putative anti-diabetic potential

    Directory of Open Access Journals (Sweden)

    Farhaneen Afzal Mazlan

    2015-10-01

    Full Text Available Lactobacillus plantarum BET003 isolated from Momordica charantia fruit was used to ferment its juice. Momordica charantia fresh juice was able to support good growth of the lactic acid bacterium. High growth rate and cell viability were obtained without further nutrient supplementation. In stirred tank reactor batch fermentation, agitation rate showed significant effect on specific growth rate of the bacterium in the fruit juice. After the fermentation, initially abundant momordicoside 23-O-β-Allopyranosyle-cucurbita-5,24-dien-7α,3β,22(R,23(S-tetraol-3-O-β-allopyranoside was transformed into its corresponding aglycone in addition to the emergence of new metabolites. The fermented M. charantia juice consistently reduced glucose production by 27.2%, 14.5%, 17.1% and 19.2% at 15-minute intervals respectively, when compared against the negative control. This putative anti-diabetic activity can be attributed to the increase in availability and concentration of aglycones as well as other phenolic compounds resulting from degradation of glycosidic momordicoside. Biotransformation of M. charantia fruit juice via lactic acid bacterium fermentation reduced its bitterness, reduced its sugar content, produced aglycones and other metabolites as well as improved its inhibition of α-glucosidase activity compared with the fresh, non-fermented juice.

  11. Biotransformation of Momordica charantia fresh juice by Lactobacillus plantarum BET003 and its putative anti-diabetic potential.

    Science.gov (United States)

    Mazlan, Farhaneen Afzal; Annuar, M Suffian M; Sharifuddin, Yusrizam

    2015-01-01

    Lactobacillus plantarum BET003 isolated from Momordica charantia fruit was used to ferment its juice. Momordica charantia fresh juice was able to support good growth of the lactic acid bacterium. High growth rate and cell viability were obtained without further nutrient supplementation. In stirred tank reactor batch fermentation, agitation rate showed significant effect on specific growth rate of the bacterium in the fruit juice. After the fermentation, initially abundant momordicoside 23-O-β-Allopyranosyle-cucurbita-5,24-dien-7α,3β,22(R),23(S)-tetraol-3-O-β-allopyranoside was transformed into its corresponding aglycone in addition to the emergence of new metabolites. The fermented M. charantia juice consistently reduced glucose production by 27.2%, 14.5%, 17.1% and 19.2% at 15-minute intervals respectively, when compared against the negative control. This putative anti-diabetic activity can be attributed to the increase in availability and concentration of aglycones as well as other phenolic compounds resulting from degradation of glycosidic momordicoside. Biotransformation of M. charantia fruit juice via lactic acid bacterium fermentation reduced its bitterness, reduced its sugar content, produced aglycones and other metabolites as well as improved its inhibition of α-glucosidase activity compared with the fresh, non-fermented juice.

  12. Surface-defect induced modifications in the optical properties of α-MnO_2 nanorods

    International Nuclear Information System (INIS)

    John, Reenu Elizabeth; Chandran, Anoop; Thomas, Marykutty; Jose, Joshy; George, K.C.

    2016-01-01

    Graphical abstract: - Highlights: • Alpha-MnO_2 nanorods are prepared by chemical method. • Difference in surface defect density is achieved. • Characterized using XRD, Rietveld, XPS, EDS, HR-TEM, BET, UV–vis absorption spectroscopy and PL spectroscopy. • Explains the bandstructure modification due to Jahn–Teller distortions using crystal field theory. • Modification in the intensity of optical emissions related to defect levels validates the concept of surface defect induced tuning of optical properties. - Abstract: The science of defect engineering via surface tuning opens a new route to modify the inherent properties of nanomaterials for advanced functional and practical applications. In this work, two independent synthesis methods (hydrothermal and co-precipitation) are adopted to fabricate α-MnO_2 nanorods with different defect structures so as to understand the effect of surface modifications on their optical properties. The crystal structure and morphology of samples are investigated with the aid of X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). Atomic composition calculated from energy dispersive spectroscopy (EDS) confirms non-stoichiometry of the samples. The surface properties and chemical environment are thoroughly studied using X-ray photoelectron spectroscopy (XPS) and Brunauer–Emmett–Teller (BET) analysis. Bond angle variance and bond valence sum are determined to validate distortions in the basic MnO_6 octahedron. The surface studies indicate that the concentration of Jahn–Teller manganese (III) (Mn"3"+) ion in the samples differ from each other which results in their distinct properties. Band structure modifications due to Jahn–Teller distortion are examined with the aid of ultraviolet–visible (UV) reflectance and photoluminescence (PL) studies. The dual peaks obtained in derivative spectrum conflict the current concept on the bandgap energy of MnO_2. These studies suggest that

  13. Influence of citric acid on SnO2 nanoparticles synthesized by wet chemical processes

    CSIR Research Space (South Africa)

    Sikhwivhilu, LM

    2010-10-01

    Full Text Available influences the particle size and the BET specific surface area. The XRD analysis revealed that nanoparticles were phase pure and that all materials exhibited a tetragonal rutile structure of SnO2. Characterisation of the materials was carried out using...

  14. CELLISA: reporter cell-based immunization and screening of hybridomas specific for cell surface antigens.

    Science.gov (United States)

    Chen, Peter; Mesci, Aruz; Carlyle, James R

    2011-01-01

    Monoclonal antibodies (mAbs) specific for cell surface antigens are an invaluable tool to study immune receptor expression and function. Here, we outline a generalized reporter cell-based approach to the generation and high-throughput screening of mAbs specific for cell surface antigens. Termed CELLISA, this technology hinges upon the capture of hybridoma supernatants in mAb arrays that facilitate ligation of an antigen of interest displayed on BWZ reporter cells in the form of a CD3ζ-fusion chimeric antigen receptor (zCAR); in turn, specific mAb-mediated cross-linking of zCAR on BWZ cells results in the production of β-galactosidase enzyme (β-gal), which can be assayed colorimetrically. Importantly, the BWZ reporter cells bearing the zCAR of interest may be used for immunization as well as screening. In addition, serial immunizations employing additional zCAR- or native antigen-bearing cell lines can be used to increase the frequency of the desired antigen-specific hybridomas. Finally, the use of a cohort of epitope-tagged zCAR (e.g., zCAR(FLAG)) variants allows visualization of the cell surface antigen prior to immunization, and coimmunization using these variants can be used to enhance the immunogenicity of the target antigen. Employing the CELLISA strategy, we herein describe the generation of mAb directed against an uncharacterized natural killer cell receptor protein.

  15. Influence of the mode of preparation of the UO3 trioxide on its specific surface

    International Nuclear Information System (INIS)

    Sauteron, J.

    1960-01-01

    As the specific surface of uranium trioxide UO 3 closely depends on the preparation mode and conditions, the authors report and discuss several results obtained on uranium trioxides produced either by precipitation of uranyl nitrate (with oxygenated water, liquid or gaseous ammoniac, and ammonium carbonate), then by calcination at 350 C, or by thermal decomposition of the uranyl nitrate. The authors also studied the influence of calcination temperature of ammonium uranate on the specific surface of the obtained oxide (between 200 and 900 deg.) [fr

  16. Non-activated high surface area expanded graphite oxide for supercapacitors

    Energy Technology Data Exchange (ETDEWEB)

    Vermisoglou, E.C.; Giannakopoulou, T.; Romanos, G.E.; Boukos, N.; Giannouri, M. [Institute of Nanoscience and Nanotechnology “Demokritos”, 153 43 Ag. Paraskevi, Attikis (Greece); Lei, C.; Lekakou, C. [Division of Mechanical, Medical, and Aerospace Engineering, Faculty of Engineering and Physical Sciences, University of Surrey, Guildford GU2 7XH (United Kingdom); Trapalis, C., E-mail: c.trapalis@inn.demokritos.gr [Institute of Nanoscience and Nanotechnology “Demokritos”, 153 43 Ag. Paraskevi, Attikis (Greece)

    2015-12-15

    Graphical abstract: - Highlights: • One-step exfoliation and reduction of graphite oxide via microwave irradiation. • Effect of pristine graphite (type, flake size) on the microwave expanded material. • Effect of pretreatment and oxidation cycles on the produced expanded material. • Expanded graphene materials with high BET surface areas (940 m{sup 2}/g–2490 m{sup 2}/g). • Non-activated graphene based materials suitable for supercapacitors. - Abstract: Microwave irradiation of graphite oxide constitutes a facile route toward production of reduced graphene oxide, since during this treatment both exfoliation and reduction of graphite oxide occurs. In this work, the effect of pristine graphite (type, size of flakes), pretreatment and oxidation cycles on the finally produced expanded material was examined. All the types of graphite that were tested afforded materials with high BET surface areas ranging from 940 m{sup 2}/g to 2490 m{sup 2}/g, without intervening an activation stage at elevated temperature. SEM and TEM images displayed exfoliated structures, where the flakes were significantly detached and curved. The quality of the reduced graphene oxide sheets was evidenced both by X-ray photoelectron spectroscopy and Raman spectroscopy. The electrode material capacitance was determined via electrochemical impedance spectroscopy and cyclic voltammetry. The materials with PEDOT binder had better performance (∼97 F/g) at low operation rates while those with PVDF binder performed better (∼20 F/g) at higher rates, opening up perspectives for their application in supercapacitors.

  17. Human milk containing specific secretory IgA inhibits binding of Giardia lamblia to nylon and glass surfaces.

    Science.gov (United States)

    Samra, H K; Ganguly, N K; Mahajan, R C

    1991-06-01

    The effects of human milk, containing specific secretory IgA, on the adherence of Giardia lamblia trophozoites in the presence and in the absence of intestinal mucus in vitro were studied. It was found that the trophozoites treated with breast milk, containing specific secretory IgA to G. lamblia, showed a significant decrease (p less than 0.01) in adherence to nylon fibre columns and glass surfaces than did trophozoites treated with milk containing no SIgA antibodies. The adherence to glass surfaces was significantly more (p less than 0.01) in the presence of intestinal mucus than when the mucus was absent. Milk that did not contain specific secretory SIgA to G. lamblia did not decrease the adherence to glass surfaces either in the presence or in the absence of mucus. The fluorescence study revealed the binding of specific secretory IgA on the trophozoite surface. The results suggest that binding of SIgA antibodies in milk to G. lamblia trophozoites inhibits parasite adherence, thus protecting against this infection in breast-fed babies.

  18. Hydrothermal Synthesis of Highly Water-dispersible Anatase Nanoparticles with Large Specific Surface Area and Their Adsorptive Properties

    Directory of Open Access Journals (Sweden)

    Hu Xueting

    2016-01-01

    Full Text Available Highly water-dispersible and very small TiO2 nanoparticles (~3 nm anatase with large specific surface area have been synthesized by hydrolysis and hydrothermal reactions of titanium butoxide and used for the removal of three azo dyes (Congo red, orange II, and methyl orange with different molecular structure from simulated wastewaters. The synthesized TiO2 nanoparticles are well dispersed in water with large specific surface area up to 417 m2 g−1. Adsorption experiments demonstrated that the water-dispersible TiO2 nanoparticles possess excellent adsorption capacities for Congo red, orange II, and methyl orange, which could be attributed to their good water-dispersibility and large specific surface area.

  19. Measurement of the specific surface area of loose copper deposit by electrochemical methods

    Directory of Open Access Journals (Sweden)

    E. A. Dolmatova

    2016-07-01

    Full Text Available In the work the surface area of the electrode with dispersed copper deposit obtained within 30 seconds was evaluated by techniques of chronopotentiometry (CPM and impedance spectroscopy. In method CPM the electrode surface available for measurement depends on the value of the polarizing current. At high currents during the transition time there is a change of surface relief that can not determine the full surface of loose deposit. The electrochemical impedance method is devoid of this shortcoming since the measurements are carried out in indifferent electrolyte in the absence of current. The area measured by the impedance is tens of times higher than the value obtained by chronopotentiometry. It is found that from a solution containing sulfuric acid the deposits form with a high specific surface area. Based on these data it was concluded that the method of impedance spectroscopy can be used to measure in situ the surface area of the dispersed copper deposits.

  20. A process to enhance the specific surface area and capacitance of hydrothermally reduced graphene oxide

    KAUST Repository

    Alazmi, Amira

    2016-08-26

    The impact of post-synthesis processing in reduced graphene oxide materials for supercapacitor electrodes has been analyzed. A comparative study of vacuum, freeze and critical point drying was carried out for hydrothermally reduced graphene oxide demonstrating that the optimization of the specific surface area and preservation of the porous network are critical to maximize its supercapacitance performance. As described below, using a supercritical fluid as the drying medium, unprecedented values of the specific surface area (364 m2 g−1) and supercapacitance (441 F g−1) for this class of materials have been achieved.

  1. A process to enhance the specific surface area and capacitance of hydrothermally reduced graphene oxide

    KAUST Repository

    Alazmi, Amira; El Tall, Omar; Rasul, Shahid; Hedhili, Mohamed N.; Patole, Shashikant P.; Da Costa, Pedro M. F. J.

    2016-01-01

    The impact of post-synthesis processing in reduced graphene oxide materials for supercapacitor electrodes has been analyzed. A comparative study of vacuum, freeze and critical point drying was carried out for hydrothermally reduced graphene oxide demonstrating that the optimization of the specific surface area and preservation of the porous network are critical to maximize its supercapacitance performance. As described below, using a supercritical fluid as the drying medium, unprecedented values of the specific surface area (364 m2 g−1) and supercapacitance (441 F g−1) for this class of materials have been achieved.

  2. Tuning the Pore Geometry of Ordered Mesoporous Carbons for Enhanced Adsorption of Bisphenol-A

    Directory of Open Access Journals (Sweden)

    Wannes Libbrecht

    2015-04-01

    Full Text Available Mesoporous carbons were synthesized via both soft and hard template methods and compared to a commercial powder activated carbon (PAC for the adsorption ability of bisphenol-A (BPA from an aqueous solution. The commercial PAC had a BET-surface of 1027 m2/g with fine pores of 3 nm and less. The hard templated carbon (CMK-3 material had an even higher BET-surface of 1420 m2/g with an average pore size of 4 nm. The soft templated carbon (SMC reached a BET-surface of 476 m2/g and a pore size of 7 nm. The maximum observed adsorption capacity (qmax of CMK-3 was the highest with 474 mg/g, compared to 290 mg/g for PAC and 154 mg/g for SMC. The difference in adsorption capacities was attributed to the specific surface area and hydrophobicity of the adsorbent. The microporous PAC showed the slowest adsorption, while the ordered mesopores of SMC and CMK-3 enhanced the BPA diffusion into the adsorbent. This difference in adsorption kinetics is caused by the increase in pore diameter. However, CMK-3 with an open geometry consisting of interlinked nanorods allows for even faster intraparticle diffusion.

  3. Tuning the Pore Geometry of Ordered Mesoporous Carbons for Enhanced Adsorption of Bisphenol-A

    Science.gov (United States)

    Libbrecht, Wannes; Vandaele, Koen; De Buysser, Klaartje; Verberckmoes, An; Thybaut, Joris W.; Poelman, Hilde; De Clercq, Jeriffa; Van Der Voort, Pascal

    2015-01-01

    Mesoporous carbons were synthesized via both soft and hard template methods and compared to a commercial powder activated carbon (PAC) for the adsorption ability of bisphenol-A (BPA) from an aqueous solution. The commercial PAC had a BET-surface of 1027 m2/g with fine pores of 3 nm and less. The hard templated carbon (CMK-3) material had an even higher BET-surface of 1420 m2/g with an average pore size of 4 nm. The soft templated carbon (SMC) reached a BET-surface of 476 m2/g and a pore size of 7 nm. The maximum observed adsorption capacity (qmax) of CMK-3 was the highest with 474 mg/g, compared to 290 mg/g for PAC and 154 mg/g for SMC. The difference in adsorption capacities was attributed to the specific surface area and hydrophobicity of the adsorbent. The microporous PAC showed the slowest adsorption, while the ordered mesopores of SMC and CMK-3 enhanced the BPA diffusion into the adsorbent. This difference in adsorption kinetics is caused by the increase in pore diameter. However, CMK-3 with an open geometry consisting of interlinked nanorods allows for even faster intraparticle diffusion. PMID:28788023

  4. Clinical Remission of Sight-Threatening Non-Infectious Uveitis Is Characterized by an Upregulation of Peripheral T-Regulatory Cell Polarized Towards T-bet and TIGIT.

    Science.gov (United States)

    Gilbert, Rose M; Zhang, Xiaozhe; Sampson, Robert D; Ehrenstein, Michael R; Nguyen, Dao X; Chaudhry, Mahid; Mein, Charles; Mahmud, Nadiya; Galatowicz, Grazyna; Tomkins-Netzer, Oren; Calder, Virginia L; Lightman, Sue

    2018-01-01

    Non-infectious uveitis can cause chronic relapsing and remitting ocular inflammation, which may require high dose systemic immunosuppression to prevent severe sight loss. It has been classically described as an autoimmune disease, mediated by pro-inflammatory Th1 and Th17 T-cell subsets. Studies suggest that natural immunosuppressive CD4 + CD25 + FoxP3 + T-regulatory cells (Tregs) are involved in resolution of inflammation and may be involved in the maintenance of clinical remission. To investigate whether there is a peripheral blood immunoregulatory phenotype associated with clinical remission of sight-threatening non-infectious uveitis by comparing peripheral blood levels of Treg, Th1, and Th17, and associated DNA methylation and cytokine levels in patients with active uveitic disease, control subjects and patients (with previously active disease) in clinical remission induced by immunosuppressive drugs. Isolated peripheral blood mononuclear cells (PBMC) from peripheral blood samples from prospectively recruited subjects were analyzed by flow cytometry for CD3, CD4, FoxP3, TIGIT, T-bet, and related orphan receptor γt. Epigenetic DNA methylation levels of FOXP3 Treg-specific demethylated region (TSDR), FOXP3 promoter, TBX21, RORC2, and TIGIT loci were determined in cryopreserved PBMC using a next-generation sequencing approach. Related cytokines were measured in blood sera. Functional suppressive capacity of Treg was assessed using T-cell proliferation assays. Fifty patients with uveitis (intermediate, posterior, and panuveitis) and 10 control subjects were recruited. The frequency of CD4 + CD25 + FoxP3 + Treg, TIGIT + Treg, and T-bet + Treg and the ratio of Treg to Th1 were significantly higher in remission patients compared with patients with active uveitic disease; and TIGIT + Tregs were a significant predictor of clinical remission. Treg from patients in clinical remission demonstrated a high level of in vitro suppressive function compared with Treg from

  5. Study on photocatalysis of TiO2 nanotubes prepared by methanol ...

    Indian Academy of Sciences (India)

    TiO2 nanotubes were synthesized by the solvothermal process at low temperature in a highly alkaline water–methanol mixed solution. Their characteristics were identified by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), specific surface area (BET), Fourier transform infrared spectroscopy (FTIR) ...

  6. Surface-defect induced modifications in the optical properties of α-MnO{sub 2} nanorods

    Energy Technology Data Exchange (ETDEWEB)

    John, Reenu Elizabeth [Department of Physics, St. Berchmans College, Changanassery, Kerala 686101 (India); Chandran, Anoop [School of Pure and Applied Physics, MG University, Kottayam, Kerala 686560 (India); Thomas, Marykutty [Department of Physics, BCM College, Kottayam, Kerala 686001 (India); Jose, Joshy [Department of Physics, St. Berchmans College, Changanassery, Kerala 686101 (India); George, K.C., E-mail: drkcgeorge@gmail.com [Department of Physics, St. Berchmans College, Changanassery, Kerala 686101 (India)

    2016-03-30

    Graphical abstract: - Highlights: • Alpha-MnO{sub 2} nanorods are prepared by chemical method. • Difference in surface defect density is achieved. • Characterized using XRD, Rietveld, XPS, EDS, HR-TEM, BET, UV–vis absorption spectroscopy and PL spectroscopy. • Explains the bandstructure modification due to Jahn–Teller distortions using crystal field theory. • Modification in the intensity of optical emissions related to defect levels validates the concept of surface defect induced tuning of optical properties. - Abstract: The science of defect engineering via surface tuning opens a new route to modify the inherent properties of nanomaterials for advanced functional and practical applications. In this work, two independent synthesis methods (hydrothermal and co-precipitation) are adopted to fabricate α-MnO{sub 2} nanorods with different defect structures so as to understand the effect of surface modifications on their optical properties. The crystal structure and morphology of samples are investigated with the aid of X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). Atomic composition calculated from energy dispersive spectroscopy (EDS) confirms non-stoichiometry of the samples. The surface properties and chemical environment are thoroughly studied using X-ray photoelectron spectroscopy (XPS) and Brunauer–Emmett–Teller (BET) analysis. Bond angle variance and bond valence sum are determined to validate distortions in the basic MnO{sub 6} octahedron. The surface studies indicate that the concentration of Jahn–Teller manganese (III) (Mn{sup 3+}) ion in the samples differ from each other which results in their distinct properties. Band structure modifications due to Jahn–Teller distortion are examined with the aid of ultraviolet–visible (UV) reflectance and photoluminescence (PL) studies. The dual peaks obtained in derivative spectrum conflict the current concept on the bandgap energy of MnO{sub 2}. These

  7. Increasing the Detection Limit of the Parkinson Disorder through a Specific Surface Chemistry Applied onto Inner Surface of the Titration Well

    Directory of Open Access Journals (Sweden)

    Fabienne Poncin-Epaillard

    2012-04-01

    Full Text Available The main objective of this paper was to illustrate the enhancement of the sensitivity of ELISA titration for neurodegenerative proteins by reducing nonspecific adsorptions that could lead to false positives. This goal was obtained thanks to the association of plasma and wet chemistries applied to the inner surface of the titration well. The polypropylene surface was plasma-activated and then, dip-coated with different amphiphilic molecules. These molecules have more or less long hydrocarbon chains and may be charged. The modified surfaces were characterized in terms of hydrophilic—phobic character, surface chemical groups and topography. Finally, the coated wells were tested during the ELISA titration of the specific antibody capture of the α-synuclein protein. The highest sensitivity is obtained with polar (Θ = 35°, negatively charged and smooth inner surface.

  8. Sol-gel preparation of high surface area potassium tetratitanate for the immobilization of nuclear waste metal ions

    International Nuclear Information System (INIS)

    Jung, K.T.; Shul, Y.G.; Moon, J.K.; Oh, W.J.

    1997-01-01

    Potassium tetratinates(K 2 Ti 4 O 9 ) were synthesized by using the sol-gel method to produce ion-exchangeable materials with high surface area. The effects of mole ratios of K/Ti and H 2 O/Ti were examined. K 2 Ti 4 O 9 was obtained at 740 deg. C by the sol-gel method, which uses a lower temperature than the melting method. After calcination at 800 deg. C, K 2 Ti 4 O exhibits a needle shape which is quite different from the shape of K 2 Ti 6 O 13 powder. The surface areas of K 2 Ti 4 O 9 was 15 m 2 /g by the sol-gel method after calcining at 800 C. The enhancement of BET area to 25 m 2 /g was obtained after supercritical drying using EtOH as solvent. By using the sodium alginate method, needle type potassium titanate 10μm in length, the longest aspect ratio of 1,3 x 10 3 could be obtained. There are variations in the Sr 2+ ion exchange rate and capacity according to the preparation method. Larger BET surface area provides fast ion exchange and larger capacity for Sr 2+ ion in the order; sol-gel process with supercritical drying > sol-gel process > melting process. (author). 17 refs, 21 figs, 1 tab

  9. Polyaniline nanofibers with a high specific surface area and an improved pore structure for supercapacitors

    Science.gov (United States)

    Xu, Hailing; Li, Xingwei; Wang, Gengchao

    2015-10-01

    Polyaniline (PANI) with a high specific surface area and an improved pore structure (HSSA-PANI) has been prepared by using a facile method, treating PANI nanofibers with chloroform (CHCl3), and its structure, morphology and pore structure are investigated. The specific surface area and pore volume of HSSA-PANI are 817.3 m2 g-1 and 0.6 cm3 g-1, and those of PANI are 33.6 m2 g-1 and 0.2 cm3 g-1. As electrode materials, a large specific surface area and pore volume can provide high electroactive regions, accelerate the diffusion of ions, and mitigate the electrochemical degradation of active materials. Compared with PANI, the capacity retention rate of HSSA-PANI is 90% with a growth of current density from 5.0 to 30 A g-1, and that of PANI is 29%. At a current density of 30 A g-1, the specific capacitance of HSSA-PANI still reaches 278.3 F g-1, and that of PANI is 86.7 F g-1. At a current density of 5.0 A g-1, the capacitance retention of HSSA-PANI is 53.1% after 2000 cycles, and that of PANI electrode is only 28.1%.

  10. An Improved MUSIC Model for Gibbsite Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell, Scott C.; Bickmore, Barry R.; Tadanier, Christopher J.; Rosso, Kevin M.

    2004-06-01

    Here we use gibbsite as a model system with which to test a recently published, bond-valence method for predicting intrinsic pKa values for surface functional groups on oxides. At issue is whether the method is adequate when valence parameters for the functional groups are derived from ab initio structure optimization of surfaces terminated by vacuum. If not, ab initio molecular dynamics (AIMD) simulations of solvated surfaces (which are much more computationally expensive) will have to be used. To do this, we had to evaluate extant gibbsite potentiometric titration data that where some estimate of edge and basal surface area was available. Applying BET and recently developed atomic force microscopy methods, we found that most of these data sets were flawed, in that their surface area estimates were probably wrong. Similarly, there may have been problems with many of the titration procedures. However, one data set was adequate on both counts, and we applied our method of surface pKa int prediction to fitting a MUSIC model to this data with considerable success—several features of the titration data were predicted well. However, the model fit was certainly not perfect, and we experienced some difficulties optimizing highly charged, vacuum-terminated surfaces. Therefore, we conclude that we probably need to do AIMD simulations of solvated surfaces to adequately predict intrinsic pKa values for surface functional groups.

  11. An automatic rat brain extraction method based on a deformable surface model.

    Science.gov (United States)

    Li, Jiehua; Liu, Xiaofeng; Zhuo, Jiachen; Gullapalli, Rao P; Zara, Jason M

    2013-08-15

    The extraction of the brain from the skull in medical images is a necessary first step before image registration or segmentation. While pre-clinical MR imaging studies on small animals, such as rats, are increasing, fully automatic imaging processing techniques specific to small animal studies remain lacking. In this paper, we present an automatic rat brain extraction method, the Rat Brain Deformable model method (RBD), which adapts the popular human brain extraction tool (BET) through the incorporation of information on the brain geometry and MR image characteristics of the rat brain. The robustness of the method was demonstrated on T2-weighted MR images of 64 rats and compared with other brain extraction methods (BET, PCNN, PCNN-3D). The results demonstrate that RBD reliably extracts the rat brain with high accuracy (>92% volume overlap) and is robust against signal inhomogeneity in the images. Copyright © 2013 Elsevier B.V. All rights reserved.

  12. Nanoporous ultrahigh specific surface polyacrylonitrile fibres

    International Nuclear Information System (INIS)

    Zhang Lifeng; Hsieh, Y-L

    2006-01-01

    The concept of phase separation was coupled with electrospinning to generate polyacrylonitrile (PAN) and poly(ethylene oxide) (PEO) bicomponent fibres that, upon removal of the phase-separated PEO domains, became nanoporous. Electrospinning of PAN (150 kDa) with 15-50% w/w PEO (10 kDa) at a 8% w/w total concentration in N,N-dimethylformamide produced fibres with decreasing averaged diameters from 390 to 130 nm. Evidence of phase separation between PAN and PEO in the bicomponent fibres was indicated by the characteristic PAN and PEO peaks by Fourier transform infrared (FTIR) spectroscopy and solid-state nuclear magnetic resonance (NMR) imaging, and confirmed by the co-existence of PAN cyclization and PEO melting by differential scanning calorimetry (DSC) and the presence of PEO crystalline diffraction by wide-angle x-ray scattering (WAXS). Removal of PEO by dissolution in water was confirmed by the matched mass loss to PEO fraction and the absence of PEO by FTIR and DSC. The water-treated bicomponent fibres appeared slightly larger in diameter and contained internal pores of nanometre scale. The nanoporous fibres generated from 50/50 PAN/PEO bicomponent precursor contained internal pores of a few nanometres to tens of nanometres in size and had 50% higher pore volume and 2.5-fold higher specific surface

  13. Ambient pressure dried tetrapropoxysilane-based silica aerogels with high specific surface area

    Science.gov (United States)

    Parale, Vinayak G.; Han, Wooje; Jung, Hae-Noo-Ree; Lee, Kyu-Yeon; Park, Hyung-Ho

    2018-01-01

    In the present paper, we report the synthesis of tetrapropoxysilane (TPOS)-based silica aerogels with high surface area and large pore volume. The silica aerogels were prepared by a two-step sol-gel process followed by surface modification via a simple ambient pressure drying approach. In order to minimize drying shrinkage and obtain hydrophobic aerogels, the surface of the alcogels was modified using trichloromethylsilane as a silylating agent. The effect of the sol-gel compositional parameters on the polymerization of aerogels prepared by TPOS, one of the precursors belonging to the Si(OR)4 family, was reported for the first time. The oxalic acid and NH4OH concentrations were adjusted to achieve good-quality aerogels with high surface area, low density, and high transparency. Controlling the hydrolysis and condensation reactions of the TPOS precursor turned out to be the most important factor to determine the pore characteristics of the aerogel. Highly transparent aerogels with high specific surface area (938 m2/g) and low density (0.047 g/cm3) could be obtained using an optimized TPOS/MeOH molar ratio with appropriate concentrations of oxalic acid and NH4OH.

  14. Effector/memory CD4 T cells making either Th1 or Th2 cytokines commonly co-express T-bet and GATA-3.

    Directory of Open Access Journals (Sweden)

    Arundhoti Das

    Full Text Available Naïve CD4 T (NCD4T cells post-activation undergo programming for inducible production of cytokines leading to generation of memory cells with various functions. Based on cytokine based polarization of NCD4T cells in vitro, programming for either 'Th1' (interferon-gamma [IFNg] or 'Th2' (interleukin [IL]-4/5/13 cytokines is thought to occur via mutually exclusive expression and functioning of T-bet or GATA-3 transcription factors (TFs. However, we show that a high proportion of mouse and human memory-phenotype CD4 T (MCD4T cells generated in vivo which expressed either Th1 or Th2 cytokines commonly co-expressed T-bet and GATA-3. While T-bet levels did not differ between IFNg-expressing and IL-4/5/13-expressing MCD4T cells, GATA-3 levels were higher in the latter. These observations were also confirmed in MCD4T cells from FVB/NJ or aged C57BL/6 or IFNg-deficient mice. While MCD4T cells from these strains showed greater Th2 commitment than those from young C57BL/6 mice, pattern of co-expression of TF was similar. Effector T cells generated in vivo following immunization also showed TF co-expression in Th1 or Th2 cytokine producing cells. We speculated that the difference in TF expression pattern of MCD4T cells generated in vivo and those generated in cytokine polarized cultures in vitro could be due to relative absence of polarizing conditions during activation in vivo. We tested this by NCD4T cell activation in non-polarizing conditions in vitro. Anti-CD3 and anti-CD28-mediated priming of polyclonal NCD4T cells in vitro without polarizing milieu generated cells that expressed either IFNg or IL-4/5/13 but not both, yet both IFNg- and IL-4/5/13-expressing cells showed upregulation of both TFs. We also tested monoclonal T cell populations activated in non-polarizing conditions. TCR-transgenic NCD4T cells primed in vitro by cognate peptide in non-polarizing conditions which expressed either IFNg or IL-4/5/13 also showed a high proportion of cells co

  15. Extraction of Some Divalent Metal Ions (Cadmium, Nickel and Lead from Different Tea and Rice Samples Using Ghezeljeh Nanoclay (Geleh-Sar-Shoor as a New Natural Sorbent

    Directory of Open Access Journals (Sweden)

    Zahra Hassanzadeh Siahpoosh

    2016-12-01

    Full Text Available This article presents the method of extraction-preconcentration of Lead, Cadmium, and Nickel ions from food samples using the Ghezeljeh montmorillonite nanoclay (Geleh-Sar-Shoor as a new native adsorbent in batch single component systems. The extraction-preconcentration of heavy metals were carried out by applying the solid phase extraction (SPE method followed by atomic absorption spectroscopy (AAS, and inductively coupled with plasma atomic emission spectroscopy (ICP-AES. The Ghezeljeh nanoclay was characterized by using Fourier transform infrared spectroscopy (FT-IR, Scanning electron microscopy-energy dispersive spectrometer operating (SEM-EDS, X-ray diffractometry (XRD, X-ray fluorescence (XRF, Cation Exchange Capacity (CEC measurements, BET specific surface area and Zeta potential. According to BET theory, the specific surface areas of the Ghezeljeh nanoclay was calculated to be 19.8 m2 g-1 whereas the cation exchange capacity was measured to be 150 meq/100 g. The results of XRD, XRF, FT-IR, Zeta potential and BET surface area of the nanoclay confirmed that montmorillonite was the dominant mineral phase. Based on SEM images of this clay, it can be seen that the distance between the plates is nm level. For all three ions, the detection and quantification limits, dynamic linear range, preconcentration factor, and adsorption capacity were obtained. The effect of various interfering ions was studied. The experimental method was successfully applied for the extraction of heavy metals in different tea and rice samples.

  16. PENGARUH STRATEGI PEMBELAJARAN BIOLOGY ENVIRONMENT TECHNOLOGY SOCIETY (BETS) TERHADAP KEMAMPUAN BERPIKIR KRITIS DAN HASIL BELAJAR BIOLOGI KELAS X KOTA MALANG

    OpenAIRE

    Eka Arum Sasi Mahardika; Hadi Suwono; Sri Endah Indriwati

    2016-01-01

    This study aims to determine the effect BETS learning to critical thinking skills and learning outcomes biology class X Senior High School in Malang. This research was conducted at SMAN 7 Malang from February-May 2016. Critical thinking skills and cognitive learning outcomes measured by a written test, whereas affective and psikomor measured by observations during the learning activities. Result critical thinking skills and cognitive learning outcomes were analyzed using statistical test with...

  17. Hierarchical porous carbon derived from Allium cepa for supercapacitors through direct carbonization method with the assist of calcium acetate

    KAUST Repository

    Xu, Jinhui; Zhang, Wenli; Hou, Dianxun; Huang, Weimin; Lin, Haibo

    2017-01-01

    In this paper, a direction carbonization method was used to prepare porous carbon from Allium cepa for supercapacitor applications. In this method, calcium acetate was used to assist carbonization process. Scanning electron microscope (SEM) and N2 adsorption/desorption method were used to characterize the morphology, Brunauer-Emmett-Teller (BET) specific surface area and pore size distribution of porous carbon derived from Allium cepa (onion derived porous carbon, OPC). OPC is of hierarchical porous structure with high specific surface area and relatively high specific capacitance. OPC possesses relatively high specific surface area of 533.5 m2/g. What’s more, OPC possesses a specific capacitance of 133.5 F/g at scan rate of 5 mV/s.

  18. Hierarchical porous carbon derived from Allium cepa for supercapacitors through direct carbonization method with the assist of calcium acetate

    KAUST Repository

    Xu, Jinhui

    2017-11-02

    In this paper, a direction carbonization method was used to prepare porous carbon from Allium cepa for supercapacitor applications. In this method, calcium acetate was used to assist carbonization process. Scanning electron microscope (SEM) and N2 adsorption/desorption method were used to characterize the morphology, Brunauer-Emmett-Teller (BET) specific surface area and pore size distribution of porous carbon derived from Allium cepa (onion derived porous carbon, OPC). OPC is of hierarchical porous structure with high specific surface area and relatively high specific capacitance. OPC possesses relatively high specific surface area of 533.5 m2/g. What’s more, OPC possesses a specific capacitance of 133.5 F/g at scan rate of 5 mV/s.

  19. Spectroscopic study on variations in illite surface properties after acid-base titration.

    Science.gov (United States)

    Liu, Wen-xin; Coveney, R M; Tang, Hong-xiao

    2003-07-01

    FT-IR, Raman microscopy, XRD, 29Si and 27Al MAS NMR, were used to investigate changes in surface properties of a natural illite sample after acid-base potentiometric titration. The characteristic XRD lines indicated the presence of surface Al-Si complexes, preferable to Al(OH)3 precipitates. In the microscopic Raman spectra, the vibration peaks of Si-O and Al-O bonds diminished as a result of treatment with acid, then increased after hydroxide back titration. The varied ratio of signal intensity between (IV)Al and (VI)Al species in 27Al MAS NMR spectra, together with the stable BET surface area after acidimetric titration, suggested that edge faces and basal planes in the layer structure of illite participated in dissolution of structural components. The combined spectroscopic evidence demonstrated that the reactions between illite surfaces and acid-leaching silicic acid and aluminum ions should be considered in the model description of surface acid-base properties of the aqueous illite.

  20. The illusion of specific capture: surface and solution studies of suboptimal oligonucleotide hybridization

    Science.gov (United States)

    2013-01-01

    Background Hybridization based assays and capture systems depend on the specificity of hybridization between a probe and its intended target. A common guideline in the construction of DNA microarrays, for instance, is that avoiding complementary stretches of more than 15 nucleic acids in a 50 or 60-mer probe will eliminate sequence specific cross-hybridization reactions. Here we present a study of the behavior of partially matched oligonucleotide pairs with complementary stretches starting well below this threshold complementarity length – in silico, in solution, and at the microarray surface. The modeled behavior of pairs of oligonucleotide probes and their targets suggests that even a complementary stretch of sequence 12 nt in length would give rise to specific cross-hybridization. We designed a set of binding partners to a 50-mer oligonucleotide containing complementary stretches from 6 nt to 21 nt in length. Results Solution melting experiments demonstrate that stable partial duplexes can form when only 12 bp of complementary sequence are present; surface hybridization experiments confirm that a signal close in magnitude to full-strength signal can be obtained from hybridization of a 12 bp duplex within a 50mer oligonucleotide. Conclusions Microarray and other molecular capture strategies that rely on a 15 nt lower complementarity bound for eliminating specific cross-hybridization may not be sufficiently conservative. PMID:23445545

  1. Effects of nasal corticosteroids on boosts of systemic allergen-specific IgE production induced by nasal allergen exposure.

    Directory of Open Access Journals (Sweden)

    Cornelia Egger

    Full Text Available Allergen exposure via the respiratory tract and in particular via the nasal mucosa boosts systemic allergen-specific IgE production. Intranasal corticosteroids (INCS represent a first line treatment of allergic rhinitis but their effects on this boost of allergen-specific IgE production are unclear.Here we aimed to determine in a double-blind, placebo-controlled study whether therapeutic doses of an INCS preparation, i.e., nasal fluticasone propionate, have effects on boosts of allergen-specific IgE following nasal allergen exposure.Subjects (n = 48 suffering from grass and birch pollen allergy were treated with daily fluticasone propionate or placebo nasal spray for four weeks. After two weeks of treatment, subjects underwent nasal provocation with either birch pollen allergen Bet v 1 or grass pollen allergen Phl p 5. Bet v 1 and Phl p 5-specific IgE, IgG1-4, IgM and IgA levels were measured in serum samples obtained at the time of provocation and one, two, four, six and eight weeks thereafter.Nasal allergen provocation induced a median increase to 141.1% of serum IgE levels to allergens used for provocation but not to control allergens 4 weeks after provocation. There were no significant differences regarding the boosts of allergen-specific IgE between INCS- and placebo-treated subjects.In conclusion, the application of fluticasone propionate had no significant effects on the boosts of systemic allergen-specific IgE production following nasal allergen exposure.http://clinicaltrials.gov/NCT00755066.

  2. A first principles study of interactions of CO{sub 2} with surfaces of a Cu(benzene‐1,3,5‐tricarboxylate) metal organic framework

    Energy Technology Data Exchange (ETDEWEB)

    Li, Jie, E-mail: jl3336@drexel.edu [Department of Materials Science & Engineering, Drexel University, Philadelphia, PA 19104 (United States); Zhu, Chenming [CAS Key Laboratory of Low-Carbon Conversion Science and Engineering, Shanghai Advanced Research Institute, Chinese Academy of Science, Shanghai 201210 (China); Qiao, Zhen [Department of Chemistry, Drexel University, Philadelphia, PA 19104 (United States); Chen, Xinqing; Wei, Wei [CAS Key Laboratory of Low-Carbon Conversion Science and Engineering, Shanghai Advanced Research Institute, Chinese Academy of Science, Shanghai 201210 (China); Ji, Haifeng [CAS Key Laboratory of Low-Carbon Conversion Science and Engineering, Shanghai Advanced Research Institute, Chinese Academy of Science, Shanghai 201210 (China); Department of Chemistry, Drexel University, Philadelphia, PA 19104 (United States); Sohlberg, Karl [Department of Materials Science & Engineering, Drexel University, Philadelphia, PA 19104 (United States); Department of Chemistry, Drexel University, Philadelphia, PA 19104 (United States)

    2016-11-01

    Highlights: • DFT calculations are reported for a new Cu(benzene 1,3,5 tricarboxylate) MOF. • Neither of two low-index surfaces displays appreciable surface relaxation. • Strongest CO{sub 2} binding is to surface-exposed aryl groups. • Surface-exposed Cu atoms do not bind CO{sub 2} strongly, even if unsaturated. • Fitting the BET isotherm yields a binding energy in agreement with DFT calculations. - Abstract: Density functional theory is used to investigate the interaction of CO{sub 2} with the 100 and 010 surfaces of a Cu(benzene 1,3,5 tricarboxylate) metal organic framework. The calculation method is first validated by applying it to similar systems for which reliable results have been reported in literature and verifying that consistent results are obtained. The method is then applied to the Cu(benzene 1,3,5 tricarboxylate) system. The results show that neither the 100 or 010 surface undergoes major surface relaxation or surface reconstruction during structural optimization. CO{sub 2} adsorption calculations show that on the 100 surface, the CO{sub 2} molecule interacts with the surface benzene ring through π-π interaction. On the 010 surface, the interaction between the CO{sub 2} and the surface is again dominated by dispersion. Population analysis shows that a Cu atom on the 010 surface, even when nominally coordinatively unsaturated, is not electron deficient, which explains why CO{sub 2} does not bind to it chemically. Adsorption of multiple CO{sub 2} molecules on the 100 surface was also studied to investigate the dependence of the interaction on surface coverage. Least squares fitting of experimental adsorption versus pressure data to the BET isotherm model yields a binding energy in good agreement with the first-principles calculations.

  3. Mode Specific Electronic Friction in Dissociative Chemisorption on Metal Surfaces: H2 on Ag(111)

    Science.gov (United States)

    Maurer, Reinhard J.; Jiang, Bin; Guo, Hua; Tully, John C.

    2017-06-01

    Electronic friction and the ensuing nonadiabatic energy loss play an important role in chemical reaction dynamics at metal surfaces. Using molecular dynamics with electronic friction evaluated on the fly from density functional theory, we find strong mode dependence and a dominance of nonadiabatic energy loss along the bond stretch coordinate for scattering and dissociative chemisorption of H2 on the Ag(111) surface. Exemplary trajectories with varying initial conditions indicate that this mode specificity translates into modulated energy loss during a dissociative chemisorption event. Despite minor nonadiabatic energy loss of about 5%, the directionality of friction forces induces dynamical steering that affects individual reaction outcomes, specifically for low-incidence energies and vibrationally excited molecules. Mode-specific friction induces enhanced loss of rovibrational rather than translational energy and will be most visible in its effect on final energy distributions in molecular scattering experiments.

  4. The two-phase flow IPTT method for measurement of nonwetting-wetting liquid interfacial areas at higher nonwetting saturations in natural porous media.

    Science.gov (United States)

    Zhong, Hua; Ouni, Asma El; Lin, Dan; Wang, Bingguo; Brusseau, Mark L

    2016-07-01

    Interfacial areas between nonwetting-wetting (NW-W) liquids in natural porous media were measured using a modified version of the interfacial partitioning tracer test (IPTT) method that employed simultaneous two-phase flow conditions, which allowed measurement at NW saturations higher than trapped residual saturation. Measurements were conducted over a range of saturations for a well-sorted quartz sand under three wetting scenarios of primary drainage (PD), secondary imbibition (SI), and secondary drainage (SD). Limited sets of experiments were also conducted for a model glass-bead medium and for a soil. The measured interfacial areas were compared to interfacial areas measured using the standard IPTT method for liquid-liquid systems, which employs residual NW saturations. In addition, the theoretical maximum interfacial areas estimated from the measured data are compared to specific solid surface areas measured with the N 2 /BET method and estimated based on geometrical calculations for smooth spheres. Interfacial areas increase linearly with decreasing water saturation over the range of saturations employed. The maximum interfacial areas determined for the glass beads, which have no surface roughness, are 32±4 and 36±5 cm -1 for PD and SI cycles, respectively. The values are similar to the geometric specific solid surface area (31±2 cm -1 ) and the N 2 /BET solid surface area (28±2 cm -1 ). The maximum interfacial areas are 274±38, 235±27, and 581±160 cm -1 for the sand for PD, SI, and SD cycles, respectively, and ~7625 cm -1 for the soil for PD and SI. The maximum interfacial areas for the sand and soil are significantly larger than the estimated smooth-sphere specific solid surface areas (107±8 cm -1 and 152±8 cm -1 , respectively), but much smaller than the N 2 /BET solid surface area (1387±92 cm -1 and 55224 cm -1 , respectively). The NW-W interfacial areas measured with the two-phase flow method compare well to values measured using the standard

  5. Evaluation of surface fractal dimension of carbon for plasma-facing material damaged by hydrogen plasma

    International Nuclear Information System (INIS)

    Nishino, Nobuhiro

    1997-01-01

    The surface structure of the plasma facing materials (PFM) changes due to plasma-surface interaction in a nuclear fusion reactor. Usually B 4 C coated graphite block are used as PFM. In this report, the surface fractal was applied to study the surface structure of plasma-damaged PFM carbon. A convenient flow-type adsorption apparatus was developed to evaluate the surface fractal dimension of materials. Four branched alkanol molecules with different apparent areas were used as the probe adsorbates. The samples used here were B 4 C coated isotopic graphite which were subjected to hydrogen plasma for various periods of exposure. The monolayer capacities of these samples for alkanols were determined by applying BET theory. The surface fractal dimension was calculated using the monolayer capacities and molecular areas for probe molecules and was found to increase from 2 to 3 with the plasma exposure time. (author)

  6. Determination of the specific surface energy of oxides and glasses in the solid-state

    International Nuclear Information System (INIS)

    Andryushechkin, S.; Karpman, M.

    2000-01-01

    The production and application of coatings on glasses are used widely in technology. The coatings on glass are used for the regulation of optical, decorative, conducting and other technological and physical properties of glass. In particular, it is important to mention the application of glass fibres for the development of composite materials. However, the specific surface energy of glass and, consequently, its adhesion characteristics are relatively low. The values of these characteristics can be changed by the application of different metallic and nonmetallic coatings is characterised by high surface energy. To produce metallic coatings with the required adhesion strength of glass, it is necessary to have information on the specific surface energy of inorganic glass of different chemical composition. The determination of the relationships between the properties and composition of glass is one of the fundamental problems. At present, a large amount of investigations have been carried out into the investigations of the properties of glass in relation to its composition. However, the problem of establishment of relationships between the properties and composition of glass are especially difficult when examining multicomponent systems (technical glass). It is therefore, in to analyse in each case the properties of not the entire system has a whole but the variation of the properties with temperature of the individual components included in the system, the subsequent application of the additivity principle. The large majority of the glasses represent combinations of oxides of the elements of groups I-III and oxides of the transition metals, forming the mixtures, solid solutions of chemical compounds in the glass production process. Thus, analysis of the characteristics of oxides of the alkali, alkali-earth and transition metals makes it possible to obtain initial data for the evaluation of the surface energy, density, molecular mass of glass containing these oxides

  7. Mesoporous high surface area Ce0.9Gd0.1O1.95 synthesized by spray drying

    DEFF Research Database (Denmark)

    Lundberg, Mats; Wang, Hsiang-Jen; Blennow Tullmar, Peter

    2011-01-01

    Mesoporous gadolinium doped cerium dioxide with high surface area was produced by spray drying using Pluronic 123 as surfactant. The powder, when calcined at 400 °C, had a BET surface area of 136 m2 g−1 and was polycrystalline as confirmed by XRD and TEM. XEDS confirmed Ce, Gd and O, as the only......, corresponding to the crystallite size calculated from XRD data. The similar size range of the mesopores and the observed crystallite size indicates that the porosity is partly formed from intergranular mesoporosity. Using the spray drying method of a surfactant assisted liquid precursor solution it can...

  8. The Non-Specific Binding of Fluorescent-Labeled MiRNAs on Cell Surface by Hydrophobic Interaction.

    Science.gov (United States)

    Lu, Ting; Lin, Zongwei; Ren, Jianwei; Yao, Peng; Wang, Xiaowei; Wang, Zhe; Zhang, Qunye

    2016-01-01

    MicroRNAs are small noncoding RNAs about 22 nt long that play key roles in almost all biological processes and diseases. The fluorescent labeling and lipofection are two common methods for changing the levels and locating the position of cellular miRNAs. Despite many studies about the mechanism of DNA/RNA lipofection, little is known about the characteristics, mechanisms and specificity of lipofection of fluorescent-labeled miRNAs. Therefore, miRNAs labeled with different fluorescent dyes were transfected into adherent and suspension cells using lipofection reagent. Then, the non-specific binding and its mechanism were investigated by flow cytometer and laser confocal microscopy. The results showed that miRNAs labeled with Cy5 (cyanine fluorescent dye) could firmly bind to the surface of adherent cells (Hela) and suspended cells (K562) even without lipofection reagent. The binding of miRNAs labeled with FAM (carboxyl fluorescein) to K562 cells was obvious, but it was not significant in Hela cells. After lipofectamine reagent was added, most of the fluorescently labeled miRNAs binding to the surface of Hela cells were transfected into intra-cell because of the high transfection efficiency, however, most of them were still binding to the surface of K562 cells. Moreover, the high-salt buffer which could destroy the electrostatic interactions did not affect the above-mentioned non-specific binding, but the organic solvent which could destroy the hydrophobic interactions eliminated it. These results implied that the fluorescent-labeled miRNAs could non-specifically bind to the cell surface by hydrophobic interaction. It would lead to significant errors in the estimation of transfection efficiency only according to the cellular fluorescence intensity. Therefore, other methods to evaluate the transfection efficiency and more appropriate fluorescent dyes should be used according to the cell types for the accuracy of results.

  9. The Non-Specific Binding of Fluorescent-Labeled MiRNAs on Cell Surface by Hydrophobic Interaction.

    Directory of Open Access Journals (Sweden)

    Ting Lu

    Full Text Available MicroRNAs are small noncoding RNAs about 22 nt long that play key roles in almost all biological processes and diseases. The fluorescent labeling and lipofection are two common methods for changing the levels and locating the position of cellular miRNAs. Despite many studies about the mechanism of DNA/RNA lipofection, little is known about the characteristics, mechanisms and specificity of lipofection of fluorescent-labeled miRNAs.Therefore, miRNAs labeled with different fluorescent dyes were transfected into adherent and suspension cells using lipofection reagent. Then, the non-specific binding and its mechanism were investigated by flow cytometer and laser confocal microscopy. The results showed that miRNAs labeled with Cy5 (cyanine fluorescent dye could firmly bind to the surface of adherent cells (Hela and suspended cells (K562 even without lipofection reagent. The binding of miRNAs labeled with FAM (carboxyl fluorescein to K562 cells was obvious, but it was not significant in Hela cells. After lipofectamine reagent was added, most of the fluorescently labeled miRNAs binding to the surface of Hela cells were transfected into intra-cell because of the high transfection efficiency, however, most of them were still binding to the surface of K562 cells. Moreover, the high-salt buffer which could destroy the electrostatic interactions did not affect the above-mentioned non-specific binding, but the organic solvent which could destroy the hydrophobic interactions eliminated it.These results implied that the fluorescent-labeled miRNAs could non-specifically bind to the cell surface by hydrophobic interaction. It would lead to significant errors in the estimation of transfection efficiency only according to the cellular fluorescence intensity. Therefore, other methods to evaluate the transfection efficiency and more appropriate fluorescent dyes should be used according to the cell types for the accuracy of results.

  10. Specific heats of lunar surface materials from 90 to 350 degrees Kelvin

    Science.gov (United States)

    Robie, R.A.; Hemingway, B.S.; Wilson, W.H.

    1970-01-01

    The specific heats of lunar samples 10057 and 10084 returned by the Apollo 11 mission have been measured between 90 and 350 degrees Kelvin by use of an adiabatic calorimeter. The samples are representative of type A vesicular basalt-like rocks and of finely divided lunar soil. The specific heat of these materials changes smoothly from about 0.06 calorie per gram per degree at 90 degrees Kelvin to about 0.2 calorie per gram per degree at 350 degrees Kelvin. The thermal parameter ??=(k??C)-1/2 for the lunar surface will accordingly vary by a factor of about 2 between lunar noon and midnight.

  11. Synthesis of ZSM-5 on the Surface of Foam Type Porous SiC Support

    International Nuclear Information System (INIS)

    Jung, Eunjin; Lee, Yoon Joo; Won, Ji Yeon; Kim, Younghee; Kim, Soo Ryong; Shin, Dong-Geun; Kwon, Woo Teck; Lee, Hyun Jae

    2015-01-01

    ZSM-5 crystals grew by hydrothermal synthesis method on the surface of foam type porous silicon carbide ceramics which fabricated by polymer replica method. Oxide layer was developed on the surface of the porous silicon carbide ceramics to induce growth of ZSM-5 from the surface. In this study, hydrothermal synthesis was carried out for 7 h at 150 .deg. C using TEOS, Al(NO 3 )•9H 2 O and TPAOH as raw materials in the presence of the porous silicon carbide ceramics. X-ray Powder Diffraction (XRD) and Scanning Electron Microscope (SEM) analyses were confirmed 1-3 μm sized ZSM-5 crystals have grown on the surface of porous silicon carbide ceramics. BET data shows that small pores about 10Å size drastically enhanced and surface area increased from 0.83 m 2 /g to 30.75 m 2 /g after ZSM-5 synthesis on the surface of foam type porous silicon carbide ceramics.

  12. Surface characterization and chemical analysis of bamboo substrates pretreated by alkali hydrogen peroxide.

    Science.gov (United States)

    Song, Xueping; Jiang, Yan; Rong, Xianjian; Wei, Wei; Wang, Shuangfei; Nie, Shuangxi

    2016-09-01

    The surface characterization and chemical analysis of bamboo substrates by alkali hydrogen peroxide pretreatment (AHPP) were investigated in this study. The results tended to manifest that AHPP prior to enzymatic and chemical treatment was potential for improving accessibility and reactivity of bamboo substrates. The inorganic components, organic solvent extractives and acid-soluble lignin were effectively removed by AHPP. X-ray photoelectron spectroscopy (XPS) analysis indicated that the surface of bamboo chips had less lignin but more carbohydrate after pre-treatment. Fiber surfaces became etched and collapsed, and more pores and debris on the substrate surface were observed with Scanning Electron Microscopy (SEM). Brenauer-Emmett-Teller (BET) results showed that both of pore volume and surface area were increased after AHPP. Although XRD analysis showed that AHPP led to relatively higher crystallinity, pre-extraction could overall enhance the accessibility of enzymes and chemicals into the bamboo structure. Copyright © 2016. Published by Elsevier Ltd.

  13. Area-Specific Cell Stimulation via Surface-Mediated Gene Transfer Using Apatite-Based Composite Layers

    Directory of Open Access Journals (Sweden)

    Yushin Yazaki

    2015-04-01

    Full Text Available Surface-mediated gene transfer systems using biocompatible calcium phosphate (CaP-based composite layers have attracted attention as a tool for controlling cell behaviors. In the present study we aimed to demonstrate the potential of CaP-based composite layers to mediate area-specific dual gene transfer and to stimulate cells on an area-by-area basis in the same well. For this purpose we prepared two pairs of DNA–fibronectin–apatite composite (DF-Ap layers using a pair of reporter genes and pair of differentiation factor genes. The results of the area-specific dual gene transfer successfully demonstrated that the cells cultured on a pair of DF-Ap layers that were adjacently placed in the same well showed specific gene expression patterns depending on the gene that was immobilized in theunderlying layer. Moreover, preliminary real-time PCR results indicated that multipotential C3H10T1/2 cells may have a potential to change into different types of cells depending on the differentiation factor gene that was immobilized in the underlying layer, even in the same well. Because DF-Ap layers have a potential to mediate area-specific cell stimulation on their surfaces, they could be useful in tissue engineering applications.

  14. Laminar shear stress modulates endothelial luminal surface stiffness in a tissue-specific manner.

    Science.gov (United States)

    Merna, Nick; Wong, Andrew K; Barahona, Victor; Llanos, Pierre; Kunar, Balvir; Palikuqi, Brisa; Ginsberg, Michael; Rafii, Shahin; Rabbany, Sina Y

    2018-04-17

    Endothelial cells form vascular beds in all organs and are exposed to a range of mechanical forces that regulate cellular phenotype. We sought to determine the role of endothelial luminal surface stiffness in tissue-specific mechanotransduction of laminar shear stress in microvascular mouse cells and the role of arachidonic acid in mediating this response. Microvascular mouse endothelial cells were subjected to laminar shear stress at 4 dynes/cm 2 for 12 hours in parallel plate flow chambers that enabled real-time optical microscopy and atomic force microscopy measurements of cell stiffness. Lung endothelial cells aligned parallel to flow, while cardiac endothelial cells did not. This rapid alignment was accompanied by increased cell stiffness. The addition of arachidonic acid to cardiac endothelial cells increased alignment and stiffness in response to shear stress. Inhibition of arachidonic acid in lung endothelial cells and embryonic stem cell-derived endothelial cells prevented cellular alignment and decreased cell stiffness. Our findings suggest that increased endothelial luminal surface stiffness in microvascular cells may facilitate mechanotransduction and alignment in response to laminar shear stress. Furthermore, the arachidonic acid pathway may mediate this tissue-specific process. An improved understanding of this response will aid in the treatment of organ-specific vascular disease. © 2018 John Wiley & Sons Ltd.

  15. Hydrothermal Synthesis of Highly Water-dispersible Anatase Nanoparticles with Large Specific Surface Area and Their Adsorptive Properties

    OpenAIRE

    Hu Xueting; Zhang Dongyun; Zhao Siqin; Asuha Sin

    2016-01-01

    Highly water-dispersible and very small TiO2 nanoparticles (~3 nm anatase) with large specific surface area have been synthesized by hydrolysis and hydrothermal reactions of titanium butoxide and used for the removal of three azo dyes (Congo red, orange II, and methyl orange) with different molecular structure from simulated wastewaters. The synthesized TiO2 nanoparticles are well dispersed in water with large specific surface area up to 417 m2 g−1. Adsorption experiments demonstrated that th...

  16. miR-148a is upregulated by Twist1 and T-bet and promotes Th1-cell survival by regulating the proapoptotic gene Bim.

    Science.gov (United States)

    Haftmann, Claudia; Stittrich, Anna-Barbara; Zimmermann, Jakob; Fang, Zhuo; Hradilkova, Kristyna; Bardua, Markus; Westendorf, Kerstin; Heinz, Gitta A; Riedel, René; Siede, Julia; Lehmann, Katrin; Weinberger, Esther E; Zimmel, David; Lauer, Uta; Häupl, Thomas; Sieper, Joachim; Backhaus, Marina; Neumann, Christian; Hoffmann, Ute; Porstner, Martina; Chen, Wei; Grün, Joachim R; Baumgrass, Ria; Matz, Mareen; Löhning, Max; Scheffold, Alexander; Wittmann, Jürgen; Chang, Hyun-Dong; Rajewsky, Nikolaus; Jäck, Hans-Martin; Radbruch, Andreas; Mashreghi, Mir-Farzin

    2015-04-01

    Repeatedly activated T helper 1 (Th1) cells present during chronic inflammation can efficiently adapt to the inflammatory milieu, for example, by expressing the transcription factor Twist1, which limits the immunopathology caused by Th1 cells. Here, we show that in repeatedly activated murine Th1 cells, Twist1 and T-bet induce expression of microRNA-148a (miR-148a). miR-148a regulates expression of the proapoptotic gene Bim, resulting in a decreased Bim/Bcl2 ratio. Inhibition of miR-148a by antagomirs in repeatedly activated Th1 cells increases the expression of Bim, leading to enhanced apoptosis. Knockdown of Bim expression by siRNA in miR-148a antagomir-treated cells restores viability of the Th1 cells, demonstrating that miR-148a controls survival by regulating Bim expression. Thus, Twist1 and T-bet not only control the differentiation and function of Th1 cells, but also their persistence in chronic inflammation. © 2014 The Authors. European Journal of Immunology published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Metal organic framework MIL-101(Cr) for dehydration reactions

    Indian Academy of Sciences (India)

    Porous chromium terephthalate MIL-101 (Cr-MIL-101) has been prepared by direct method under hydrothermal conditions and characterized using X-ray diffraction, N2 sorption, TGA and FT-IR. The nitrogen adsorption-desorption isotherm shows that the Cr-MIL-101 possesses BET specific surface area of 2563 m2/g.

  18. Incorporating classic adsorption isotherms into modern surface complexation models: implications for sorption of radionuclides

    International Nuclear Information System (INIS)

    Kulik, D.A.

    2005-01-01

    Full text of publication follows: Computer-aided surface complexation models (SCM) tend to replace the classic adsorption isotherm (AI) analysis in describing mineral-water interface reactions such as radionuclide sorption onto (hydr) oxides and clays. Any site-binding SCM based on the mole balance of surface sites, in fact, reproduces the (competitive) Langmuir isotherm, optionally amended with electrostatic Coulomb's non-ideal term. In most SCM implementations, it is difficult to incorporate real-surface phenomena (site heterogeneity, lateral interactions, surface condensation) described in classic AI approaches other than Langmuir's. Thermodynamic relations between SCMs and AIs that remained obscure in the past have been recently clarified using new definitions of standard and reference states of surface species [1,2]. On this basis, a method for separating the Langmuir AI into ideal (linear) and non-ideal parts [2] was applied to multi-dentate Langmuir, Frumkin, and BET isotherms. The aim of this work was to obtain the surface activity coefficient terms that make the SCM site mole balance constraints obsolete and, in this way, extend thermodynamic SCMs to cover sorption phenomena described by the respective AIs. The multi-dentate Langmuir term accounts for the site saturation with n-dentate surface species, as illustrated on modeling bi-dentate U VI complexes on goethite or SiO 2 surfaces. The Frumkin term corrects for the lateral interactions of the mono-dentate surface species; in particular, it has the same form as the Coulombic term of the constant-capacitance EDL combined with the Langmuir term. The BET term (three parameters) accounts for more than a monolayer adsorption up to the surface condensation; it can potentially describe the surface precipitation of nickel and other cations on hydroxides and clay minerals. All three non-ideal terms (in GEM SCMs implementation [1,2]) by now are used for non-competing surface species only. Upon 'surface dilution

  19. Fermi surface study of organic conductors using a magneto-optical measurement under high magnetic fields

    International Nuclear Information System (INIS)

    Kimata, M; Ohta, H; Koyama, K; Motokawa, M; Kondo, R; Kagoshima, S; Tanaka, H; Tokumoto, M; Kobayashi, H; Kobayashi, A

    2006-01-01

    Magneto-optical measurements have been performed in organic conductors β''-(BEDT-TTF) 2 CsCd(SCN) 4 and λ-(BETS) 2 FeCl 4 . Although the zero magnetic field ground state of β''-(BEDT-TTF) 2 CsCd(SCN) 4 is considered as the density wave state, periodic orbit resonances (POR's) attributed to quasi-one-dimensional (Q1D) and quasi-two-dimensional (Q2D) Fermi surfaces (FS's) have been observed above 6 T. The existence of these FS's are predicted by the band calculation based on room temperature lattice parameters. This result may suggest the destruction of the density wave state at 6 T, and the primal metallic state revives in the high field phase above 6 T. In the case of λ-(BETS) 2 FeCl 4 , large changes of the transmission intensity of electromagnetic waves around 10 T, which correspond to the insulator-metal transition, have been observed. However, no POR-like resonance has been observed. This may be due to the restriction of the observed frequency-field region

  20. Ligand-specific regulation of the extracellular surface of a G-protein-coupled receptor

    DEFF Research Database (Denmark)

    Bokoch, Michael P; Zou, Yaozhong; Rasmussen, Søren Gøgsig Faarup

    2010-01-01

    extending from the orthosteric ligand-binding site in the transmembrane core to the cytoplasmic G-protein-coupling domains. In contrast, the extracellular surface (ECS) of GPCRs is remarkably diverse and is therefore an ideal target for the discovery of subtype-selective drugs. However, little is known...... conformational coupling between the ECS and the orthosteric binding site, showing that drugs targeting this diverse surface could function as allosteric modulators with high subtype selectivity. Moreover, these studies provide a new insight into the dynamic behaviour of GPCRs not addressable by static, inactive...... about the functional role of the ECS in receptor activation, or about conformational coupling of this surface to the native ligand-binding pocket. Here we use NMR spectroscopy to investigate ligand-specific conformational changes around a central structural feature in the ECS of the beta(2) adrenergic...

  1. Surface modification, characterization and adsorptive properties of a coconut activated carbon

    Energy Technology Data Exchange (ETDEWEB)

    Lu Xincheng [Institute of Chemical Industry of Forest Products, CAF, National Engineering Lab. for Biomass Chemical Utilization, Key and Open Lab. of Forest Chemical Engineering, SFA, Key Lab. of Biomass Energy and Material, Jiangsu Province, Suojin wucun 16, Nanjing 210042 (China); Jiang Jianchun, E-mail: lhs_ac2011@yahoo.cn [Institute of Chemical Industry of Forest Products, CAF, National Engineering Lab. for Biomass Chemical Utilization, Key and Open Lab. of Forest Chemical Engineering, SFA, Key Lab. of Biomass Energy and Material, Jiangsu Province, Suojin wucun 16, Nanjing 210042 (China); Sun Kang; Xie Xinping; Hu Yiming [Institute of Chemical Industry of Forest Products, CAF, National Engineering Lab. for Biomass Chemical Utilization, Key and Open Lab. of Forest Chemical Engineering, SFA, Key Lab. of Biomass Energy and Material, Jiangsu Province, Suojin wucun 16, Nanjing 210042 (China)

    2012-08-01

    A coconut activated carbon was modified using chemical methods. Different concentration of nitric acid oxidation of the conventional sample produced samples with weakly acidic functional groups. The oxidized samples were characterized by scanning electron micrograph, nitrogen absorption-desorption, Fourier transform infra red spectroscopy, Bothem method, pH titration, adsorption capacity of sodium and formaldehyde, and the adsorption mechanism of activated carbons was investigated. The results showed that BET surface area and pore volume of activated carbons were decreased after oxidization process, while acidic functional groups were increased. The surface morphology of oxidized carbons looked clean and eroded which was caused by oxidization of nitric acid. The oxidized carbons showed high adsorption capacity of sodium and formaldehyde, and chemical properties of activated carbon played an important role in adsorption of metal ions and organic pollutants.

  2. Construction, specification, and mathematical description of aspheric surfaces.

    Science.gov (United States)

    Smith, G; Atchison, D A

    1983-03-01

    Rotationally symmetrical aspheric surfaces of spectacle lenses are constructed as either "zonal aspherics" or "continuous aspherics." Zonal aspherics consist of annular zones surrounding a central zone with each zone being nominally spherical with progressively lower surface power the farther the zone is from the surface vertex. Aspheric surfaces are often specified by the radial drop in surface power from the center to the edge of the lens (e.g., Welsh Four-drop), but for assessment purposes the surface shape must be specified more precisely. The formulas for the description of continuous aspherics can be manipulated into different forms. Mathematical descriptions are given or developed which will enable theoretical assessment of the performances of all lenses with rotationally symmetrical aspheric surfaces.

  3. Effect of selective removal of organic matter and iron oxides on the ...

    African Journals Online (AJOL)

    The effect of selective removal of organic matter and amorphous and crystalline iron oxides on N2-BET specific surface areas of some soil clays was evaluated. Clay fractions from 10 kaolinitic tropical soils were successively treated to remove organic matter by oxidation with Na hypochlorite, amorphous Fe oxide with acid ...

  4. Fabrication and characterization of akaganeite/graphene oxide nanocomposite for arsenic removal from water

    Science.gov (United States)

    Trang, Nguyen Thi Thuy; Thy, Lu Thi Mong; Cuong, Pham Mai; Tu, Tran Hoang; Hieu, Nguyen Huu

    2018-04-01

    In this study, akageneite/graphene oxide (β-FeOOH/GO) nanocomposite was fabricated by in situ forced hydrolysis of iron (III) chloride. The structure and morphology of β-FeOOH/GO were characterized by Fourier Transform Infrared Spectroscopy (FTIR), X-ray diffraction (XRD), transmission electron microscopy (TEM), and Brunauer-Emmett- Teller (BET) specific surface area. XRD, FTIR, and TEM results indicated that β-FeOOH nanoparticles were successfully decorated on the surface of GO nanosheets. The BET specific surface area of β-FeOOH/GO was observed of 97.94 m2/g. The nanocomposite was used as an adsorbent for removal of arsenic (As5+) from water. Adsorption experiments were carried out to investigate contact time, pH values, and As5+ initial concentrations. The adsorption equilibrium time was reached within 180 minutes. The adsorption was well-fitted by a pseudo-second-order kinetic and Langmuir isotherm model. The maximum adsorption capacity of β-FeOOH/GO for As5+ ions of 94.34 mg/g that was calculated from the Langmuir model at pH 3. Accordingly, the nanocomposite β-FeOOH/GO could be considered as a highly efficient adsorbent for removing arsenic from water.

  5. Synthesis and Characterization of Nanoporous Carbon Materials; The Effect of Surfactant Concentrations and Salts

    Directory of Open Access Journals (Sweden)

    Shokoofeh Geranmayeh

    2011-01-01

    Full Text Available Nanoporous carbon framework was synthesized using phenol and formaldehyde as carbon precursors and triblock copolymer (pluronic F127 as soft template via evaporation induced self-assembly. Hexagonal mesoporous carbon with specific surface area of 350 m2/g through optimizing the situation was obtained. The effects of different surfactant/phenol molar ratio and presence of salts on specific surface area, pore size and pore volume for all the prepared samples were studied by means of the Brunauer-Emmett-Teller (BET formalism, powder X-ray diffraction technique and FT-IR spectroscopy.

  6. Solution structure of the second bromodomain of Brd2 and its specific interaction with acetylated histone tails

    Directory of Open Access Journals (Sweden)

    Wu Jihui

    2007-09-01

    Full Text Available Abstract Background Brd2 is a transcriptional regulator and belongs to BET family, a less characterized novel class of bromodomain-containing proteins. Brd2 contains two tandem bromodomains (BD1 and BD2, 46% sequence identity in the N-terminus and a conserved motif named ET (extra C-terminal domain at the C-terminus that is also present in some other bromodomain proteins. The two bromodomains have been shown to bind the acetylated histone H4 and to be responsible for mitotic retention on chromosomes, which is probably a distinctive feature of BET family proteins. Although the crystal structure of Brd2 BD1 is reported, no structure features have been characterized for Brd2 BD2 and its interaction with acetylated histones. Results Here we report the solution structure of human Brd2 BD2 determined by NMR. Although the overall fold resembles the bromodomains from other proteins, significant differences can be found in loop regions, especially in the ZA loop in which a two amino acids insertion is involved in an uncommon π-helix, termed πD. The helix πD forms a portion of the acetyl-lysine binding site, which could be a structural characteristic of Brd2 BD2 and other BET bromodomains. Unlike Brd2 BD1, BD2 is monomeric in solution. With NMR perturbation studies, we have mapped the H4-AcK12 peptide binding interface on Brd2 BD2 and shown that the binding was with low affinity (2.9 mM and in fast exchange. Using NMR and mutational analysis, we identified several residues important for the Brd2 BD2-H4-AcK12 peptide interaction and probed the potential mechanism for the specific recognition of acetylated histone codes by Brd2 BD2. Conclusion Brd2 BD2 is monomeric in solution and dynamically interacts with H4-AcK12. The additional secondary elements in the long ZA loop may be a common characteristic of BET bromodomains. Surrounding the ligand-binding cavity, five aspartate residues form a negatively charged collar that serves as a secondary binding site

  7. Surface charge-specific interactions between polymer nanoparticles and ABC transporters in Caco-2 cells

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharjee, Sourav, E-mail: sourav.bhattacharjee@wur.nl [Wageningen University, Laboratory of Organic Chemistry (Netherlands); Opstal, Edward J. van; Alink, Gerrit M. [Wageningen University, Division of Toxicology (Netherlands); Marcelis, Antonius T. M.; Zuilhof, Han [Wageningen University, Laboratory of Organic Chemistry (Netherlands); Rietjens, Ivonne M. C. M. [Wageningen University, Division of Toxicology (Netherlands)

    2013-06-15

    The surface charge-dependent transport of polymeric nanoparticles (PNPs) across Caco-2 monolayers grown on transwell culture systems as an in vitro model for intestinal transport was tested. The transport of well-characterized, monodisperse, and fluorescent tri-block copolymer nanoparticles (TCNPs/size {approx}45 nm) and polystyrene nanoparticles (PSNPs/size {approx}50 nm), with different surface charges (positive and negative), was quantified. The positive PNPs showed a higher intracellular uptake and flux across the Caco-2 monolayers than the negative PNPs. Multidrug resistance/P-glycoprotein (MDR1/P-gp), a specific ATP-binding cassette (ABC) transporter, was found to play a major role in the cellular efflux of positive PNPs, whereas the multidrug resistance protein 1 took part in the efflux of negative PNPs from Caco-2 cells. The positive PNPs also caused an increased cellular uptake and apical to basolateral transport of the carcinogen PhIP across the Caco-2 monolayer. The flavonoid quercetin, which is known to interact with ABC transporters, promoted the intracellular uptake of different PNPs and interfered with the normal distribution patterns of PNPs in the transwell system. These results indicate that PNPs display surface charge-specific interactions with ABC transporters and can even affect the bioavailability of toxic food-borne compounds (like pro-carcinogens).

  8. Surface charge-specific interactions between polymer nanoparticles and ABC transporters in Caco-2 cells

    Science.gov (United States)

    Bhattacharjee, Sourav; van Opstal, Edward J.; Alink, Gerrit M.; Marcelis, Antonius T. M.; Zuilhof, Han; Rietjens, Ivonne M. C. M.

    2013-06-01

    The surface charge-dependent transport of polymeric nanoparticles (PNPs) across Caco-2 monolayers grown on transwell culture systems as an in vitro model for intestinal transport was tested. The transport of well-characterized, monodisperse, and fluorescent tri-block copolymer nanoparticles (TCNPs/size 45 nm) and polystyrene nanoparticles (PSNPs/size 50 nm), with different surface charges (positive and negative), was quantified. The positive PNPs showed a higher intracellular uptake and flux across the Caco-2 monolayers than the negative PNPs. Multidrug resistance/P-glycoprotein (MDR1/P-gp), a specific ATP-binding cassette (ABC) transporter, was found to play a major role in the cellular efflux of positive PNPs, whereas the multidrug resistance protein 1 took part in the efflux of negative PNPs from Caco-2 cells. The positive PNPs also caused an increased cellular uptake and apical to basolateral transport of the carcinogen PhIP across the Caco-2 monolayer. The flavonoid quercetin, which is known to interact with ABC transporters, promoted the intracellular uptake of different PNPs and interfered with the normal distribution patterns of PNPs in the transwell system. These results indicate that PNPs display surface charge-specific interactions with ABC transporters and can even affect the bioavailability of toxic food-borne compounds (like pro-carcinogens).

  9. Surface charge-specific interactions between polymer nanoparticles and ABC transporters in Caco-2 cells

    International Nuclear Information System (INIS)

    Bhattacharjee, Sourav; Opstal, Edward J. van; Alink, Gerrit M.; Marcelis, Antonius T. M.; Zuilhof, Han; Rietjens, Ivonne M. C. M.

    2013-01-01

    The surface charge-dependent transport of polymeric nanoparticles (PNPs) across Caco-2 monolayers grown on transwell culture systems as an in vitro model for intestinal transport was tested. The transport of well-characterized, monodisperse, and fluorescent tri-block copolymer nanoparticles (TCNPs/size ∼45 nm) and polystyrene nanoparticles (PSNPs/size ∼50 nm), with different surface charges (positive and negative), was quantified. The positive PNPs showed a higher intracellular uptake and flux across the Caco-2 monolayers than the negative PNPs. Multidrug resistance/P-glycoprotein (MDR1/P-gp), a specific ATP-binding cassette (ABC) transporter, was found to play a major role in the cellular efflux of positive PNPs, whereas the multidrug resistance protein 1 took part in the efflux of negative PNPs from Caco-2 cells. The positive PNPs also caused an increased cellular uptake and apical to basolateral transport of the carcinogen PhIP across the Caco-2 monolayer. The flavonoid quercetin, which is known to interact with ABC transporters, promoted the intracellular uptake of different PNPs and interfered with the normal distribution patterns of PNPs in the transwell system. These results indicate that PNPs display surface charge-specific interactions with ABC transporters and can even affect the bioavailability of toxic food-borne compounds (like pro-carcinogens).

  10. Flow analysis of water-powder mixtures: Application to specific surface area and shape factor

    NARCIS (Netherlands)

    Hunger, M.; Brouwers, H.J.H.

    2009-01-01

    This paper addresses the characterization of powder materials with respect to their application in concrete. Given that powders provide by far highest percentage of specific surface area in a concrete mix, their packing behavior and water demand is of vital interest for the design of concrete. They

  11. Flow analysis of water-powder mixtures : Application to specific surface area and shape factor

    NARCIS (Netherlands)

    Hunger, M.; Brouwers, H.J.H.

    2009-01-01

    This paper addresses the characterization of powder materials with respect to their application in concrete. Given that powders provide by far highest percentage of specific surface area in a concrete mix, their packing behavior and water demand is of vital interest for the design of concrete. They

  12. Surface engineered magnetic nanoparticles for specific immunotargeting of cadherin expressing cells

    International Nuclear Information System (INIS)

    Moros, Maria; Puertas, Sara; Saez, Berta; Grazú, Valeria; Delhaes, Flavien; Feracci, Helene; De la Fuente, Jesús M

    2016-01-01

    In spite of historic advances in cancer biology and recent development of sophisticated chemotherapeutics, the outlook for patients with advanced cancer is still grim. In this sense nanoparticles (NPs), through their unique physical properties, enable the development of new approaches for cancer diagnosis and treatment. Thus far the most used active targeting scheme involves NPs functionalization with antibodies specific to molecules overexpressed on cancer cell’s surface. Therefore, such active targeting relies on differences in NPs uptake kinetics rates between tumor and healthy cells. Many cancers of epithelial origin are associated with the inappropriate expression of non-epithelial cadherins (e.g. N-, P-, -11) with concomitant loss of E-cadherin. Such phenomenon named cadherin switching favors tumor development and metastasis via interactions of tumor cells with stromal components. That is why we optimized the oriented functionalization of fluorescently labelled magnetic NPs with a novel antibody specific for the extracellular domain of cadherin-11. The obtained Ab-NPs exhibited high specificity when incubated with two cell lines used as models of tumor and healthy cells. Thus, cadherin switching offers a great opportunity for the development of active targeting strategies aimed to improve the early detection and treatment of cancer. (paper)

  13. Efeito do confinamento axial no comportamento de vigas de betão estrutural sujeitas à torção

    OpenAIRE

    Taborda, Cátia Sofia Batista .

    2012-01-01

    Neste trabalho é estudado o comportamento de vigas de betão estrutural sujeitas à torção e confinadas axialmente. O estudo realizado tem por objetivo considerar a influência das reais condições de ligação das vigas aos elementos adjacentes no dimensionamento da mesma à torção. Para tal, tem-se em conta o estado de tensão de compressão longitudinal induzido pelo efeito do confinamento axial. A incorporação e estudo do efeito do confinamento axial em vigas à torção será realizado mediante a ...

  14. Guidance and methods for satisfying low specific activity material and surface contaminated object regulatory requirements

    International Nuclear Information System (INIS)

    Pope, R.B.; Shappert, L.B.; Michelhaugh, R.D.; Boyle, R.W.; Easton, E.P.; Coodk, J.R.

    1998-01-01

    The U.S. Department of Transportation (DOT) and the U.S. Nuclear Regulatory Commission (NRC) have prepared a comprehensive set of draft guidance for shippers and inspectors to use when applying the newly imposed regulatory requirements for low specific activity (LSA) material and surface contaminated objects (SCOs). These requirements represent significant departures in some areas from the manner in which these materials and objects were regulated by the earlier versions of the regulations. The proper interpretation and application of the regulatory criteria can require a fairly complex set of decisions be made. To assist those trying these regulatory requirements, a detailed set of logic-flow diagrams representing decisions related to multiple factors were prepared and included in the draft report for comment on Categorizing and Transporting Low Specific Activity Materials and Surface Contaminated Objects, (DOT/NRC, 1997). These logic-flow diagrams, as developed, are specific to the U.S. regulations, but were readily adaptable to the IAEA regulations. The diagrams have been modified accordingly and tied directly to specific paragraphs in IAEA Safety Series No. 6. This paper provides the logic-flow diagrams adapted in the IAEA regulations, and demonstrated how these diagrams can be used to assist consignors and inspectors in assessing compliance of shipments with the LSA material and SCO regulatory requirements. (authors)

  15. Kinetics and thermodynamics studies on the BMP-2 adsorption onto hydroxyapatite surface with different multi-morphological features.

    Science.gov (United States)

    Lu, Zhiwei; Huangfu, Changxin; Wang, Yanying; Ge, Hongwei; Yao, Yao; Zou, Ping; Wang, Guangtu; He, Hua; Rao, Hanbing

    2015-01-01

    The effect of the surface topography on protein adsorption process is of great significance for designing hydroxyapatite (HA) ceramic material surfaces. In this work, three different topographies of HA materials HA-sheet, HA-rod, and HA-whisker were synthesized and testified by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Brunauer-Emmett-Teller (BET) and a field emission scanning electron microscopy (FE-SEM). We have systematically investigated the adsorption kinetics and thermodynamics of bone morphogenetic proteins (BMP-2) on the three different topography surfaces of HA, respectively. The results showed that the maximum adsorption capacities of HA-sheet, HA-rod and HA-whisker were (219.96 ± 10.18), (247.13 ± 12.35), and (354.67 ± 17.73) μg · g(-1), respectively. Kinetic parameters, rate constants, equilibrium adsorption capacities and related correlation coefficients, for each kinetic model were calculated as well as discussed. It demonstrated that the adsorption of BMP-2 onto HA could be described by the pseudo second-order equation. Adsorption of BMP-2 onto HA followed the Langmuir isotherm. It confirmed that compared with other samples HA-whisker had more adsorption sites for its high specific surface area which could provide more opportunities for protein molecules. The adsorption processes were endothermic (ΔH > 0), spontaneous (ΔG 0). A possible adsorption mechanism has been proposed. In addition, the BMP-2 could be adsorbed to the surface which existed slight conformational changes by FT-IR. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. Alterations in regulatory T cells induced by specific oligosaccharides improve vaccine responsiveness in mice.

    Directory of Open Access Journals (Sweden)

    Marcel A Schijf

    Full Text Available Prophylactic vaccinations are generally performed to protect naïve individuals with or without suppressed immune responsiveness. In a mouse model for Influenza vaccinations the specific alterations of CD4(+CD25(+Foxp3(+ regulatory T-cells (Tregs in the immune modulation induced by orally supplied oligosaccharides containing scGOS/lcFOS/pAOS was assessed. This dietary intervention increased vaccine specific DTH responses. In addition, a significant increased percentage of T-bet(+ (Th1 activated CD69(+CD4(+ T cells (p<0.001 and reduced percentage of Gata-3(+ (Th2 activated CD69(+CD4(+T cells (p<0.001 was detected in the mesenteric lymph nodes (MLN of mice receiving scGOS/lcFOS/pAOS compared to control mice. Although no difference in the number or percentage of Tregs (CD4(+Foxp3(+ could be determined after scGOS/lcFOS/pAOS intervention, the percentage of CXCR3 (+ /T-bet(+ (Th1-Tregs was significantly reduced (p<0.05 in mice receiving scGOS/lcFOS/pAOS as compared to mice receiving placebo diets. Moreover, although no absolute difference in suppressive capacity could be detected, an alteration in cytokine profile suggests a regulatory T cell shift towards a reducing Th1 suppression profile, supporting an improved vaccination response.These data are indicative for improved vaccine responsiveness due to reduced Th1 suppressive capacity in the Treg population of mice fed the oligosaccharide specific diet, showing compartmentalization within the Treg population. The modulation of Tregs to control immune responses provides an additional arm of intervention using alternative strategies possibly leading to the development of improved vaccines.

  17. Synthesis of zinc aluminate with high surface area by microwave hydrothermal method applied in the transesterification of soybean oil (biodiesel)

    International Nuclear Information System (INIS)

    Quirino, M.R.; Oliveira, M.J.C.; Keyson, D.; Lucena, G.L.; Oliveira, J.B.L.; Gama, L.

    2016-01-01

    Highlights: • ZnAl_2O_4 spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min. • The powders show high specific surface area. • ZAT_b15 showed activity of 52.22% for the conversion of soybean oil into biodiesel. - Abstract: Zinc aluminate is a material with high thermal stability and high mechanical strength that, owing to these properties, is used as a catalyst or support. In this work, zinc aluminate spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min at a low temperature (150 °C) without templates, using only Al(NO_3)_3·9H_2O, Zn(NO_3)_2·6H_2O, and urea as precursors and applied in the transesterification of soybean oil. X-ray diffraction analysis showed that ZnAl_2O_4 had a cubic structure without secondary phases. The nitrogen adsorption measurements (BET) revealed a high surface area (266.57 m"2 g"−"1) for the nanopowder synthesized in 15 min. This powder showed activity of 52.22% for the catalytic conversion of soybean oil into biodiesel by transesterification.

  18. The triazine-based porous organic polymer: Novel synthetic strategy for high specific surface area

    International Nuclear Information System (INIS)

    Park, Jin Kuen

    2017-01-01

    A new type of microporous polymer has been successively synthesized via a simple polycondensation reaction with the 2,4-diaminotriazine moiety and dianhydride monomer. Diaminotriazine moieties in M1 especially can provide effective branching sites, resulting in high surface areas up to 1150 m"2 /g. In addition, the specific pore structure of the polyimide POP in its solid state can be modified by the surface activation method. Therefore, it can be expected that the resulting material will be a promising candidate for gas storage, and with this synthetic strategy, various type of derivatives will also be optimized

  19. The triazine-based porous organic polymer: Novel synthetic strategy for high specific surface area

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jin Kuen [Dept. of Chemistry, Hankuk University of Foreign Studies, Yongin (Korea, Republic of)

    2017-02-15

    A new type of microporous polymer has been successively synthesized via a simple polycondensation reaction with the 2,4-diaminotriazine moiety and dianhydride monomer. Diaminotriazine moieties in M1 especially can provide effective branching sites, resulting in high surface areas up to 1150 m{sup 2} /g. In addition, the specific pore structure of the polyimide POP in its solid state can be modified by the surface activation method. Therefore, it can be expected that the resulting material will be a promising candidate for gas storage, and with this synthetic strategy, various type of derivatives will also be optimized.

  20. Alternative route for the synthesis of high surface-area η-Al{sub 2}O{sub 3}/Nb{sub 2}O{sub 5} catalyst from aluminum waste

    Energy Technology Data Exchange (ETDEWEB)

    Nogueira, Francisco G.E. [Departamento de Engenharia Química, Universidade Federal de São Carlos, CEP 13565-905, São Carlos, SP (Brazil); Asencios, Yvan J.O. [Departamento de Ciências do Mar, Universidade Federal de São Paulo, Av. Alm. Saldanha da Gama, 89, 11030-400, Santos, SP (Brazil); Rodella, Cristiane B. [Laboratório Nacional de Luz Sincrotron, Rua Giuseppe Máximo Scolfaro, 10.000 Polo II de Alta Tecnologia, 13083-970, Campinas, SP (Brazil); Porto, André L.M. [Departamento de Engenharia Química, Universidade Federal de São Carlos, CEP 13565-905, São Carlos, SP (Brazil); Assaf, Elisabete M., E-mail: eassaf@iqsc.usp.br [Instituto de Química de São Carlos, Universidade de São Paulo, Av. Trabalhador São Carlense, 400, 13560-970, São Carlos, SP (Brazil)

    2016-12-01

    This paper describes an alternative route for the production of a high-surface-area η-Al{sub 2}O{sub 3}/Nb{sub 2}O{sub 5} catalyst synthesized from aluminum waste and niobium ammonium oxalate (NH{sub 4}H{sub 2}[NbO−(C{sub 2}O{sub 4}){sub 3}]·3H{sub 2}O). The effects of thermal treatment on the morphology and crystal structure were examined by X-ray powder diffraction (XPD), surface area measurements (BET), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray fluorescence, dynamic scanning calorimetry (DSC) and thermogravimetry (TG) measurement. The catalysts were evaluated in the glycerol dehydration reaction. Catalytic tests were carried out with reactants in gas-phase with a fixed-bed reactor at 300° and 400 °C. - Highlights: • Alternative route for the production of a high-surface-area Al{sub 2}O{sub 3}/Nb{sub 2}O{sub 5} catalyst. • The catalyst was synthesized from aluminum waste and ammonium oxalato-niobate. • NbAl catalyst obtained showed high specific surface area (330 m{sup 2}/g). • The catalyst produced by this method showed promise in the dehydration of glycerol.

  1. Surface properties and catalytic performance of Pt/LaSrCoO4 catalysts in the oxidation of hexane

    Directory of Open Access Journals (Sweden)

    Hua Zhong

    2007-08-01

    Full Text Available Perovskite-type La2 –xSrxCoO4 mixed oxides have been prepared by calcination at various temperatures of precipitates obtained from aqueous solutions in the presence of citric or ethylenediamintetraacetic (EDTA acids, and have been studied by X-ray diffraction (XRD, surface area (BET measurements, temperature programmed desorption (TPD, temperature programmed reduction (TPR and X-ray photoelectron spectroscopy (XPS. These oxides are catalysts for hexane oxidation, with the greatest activity for LaSrCoO4 calcined at 750 C. This has extensive oxygen vacancies and large internal surface area. Pt-modified LaSrCoO4 catalysts are significantly more active than the Pt-free system. Both surface and bulk phases of the preovskitetype oxides contribute to hexane oxidation.

  2. Preparation and surface properties of mesoporous silica particles modified with poly(N-vinyl-2-pyrrolidone) as a potential adsorbent for bilirubin removal

    Energy Technology Data Exchange (ETDEWEB)

    Timin, Alexander, E-mail: a_timin@mail.ru [Inorganic Chemistry Department, Ivanovo State University of Chemistry and Technology (ISUCT), 7, Sheremetevsky prosp., 153000 Ivanovo (Russian Federation); Rumyantsev, Evgeniy, E-mail: evr@isuct.ru [Inorganic Chemistry Department, Ivanovo State University of Chemistry and Technology (ISUCT), 7, Sheremetevsky prosp., 153000 Ivanovo (Russian Federation); Lanin, Sergey N., E-mail: SNLanin@phys.chem.msu.ru [Chemistry Department, Physical Chemistry Division, Lomonosov Moscow State University, 1-3 Leninskie Gory, 119991 Moscow (Russian Federation); Rychkova, Sveta A. [Chemistry Department, Physical Chemistry Division, Lomonosov Moscow State University, 1-3 Leninskie Gory, 119991 Moscow (Russian Federation); Guseynov, Sabir S. [Krestov Institute of Solution Chemistry of Russian Academy of Sciences, 153000 Ivanovo (Russian Federation); Solomonov, Alexey V. [Inorganic Chemistry Department, Ivanovo State University of Chemistry and Technology (ISUCT), 7, Sheremetevsky prosp., 153000 Ivanovo (Russian Federation); Antina, Elena V. [Krestov Institute of Solution Chemistry of Russian Academy of Sciences, 153000 Ivanovo (Russian Federation)

    2014-10-15

    The surface of silica particles was modified with polyvinyl pyrrolidone (PVP) through sol–gel process. The different experimental techniques, i.e., thermogravimetric analysis (TGA and DTG), nitrogen adsorption, scanning electron microscopy (SEM), laser diffraction analysis (LDA), fourier transform spectroscopy (FTIR) are used to characterize the pure non-functionalized and functionalized silicas containing different amount of PVP. It was shown that PVP-modified silica samples have well developed porous structure; the values of specific surface area for PVP-modified silicas are in the range of 140–264 m{sup 2} g{sup −1}. While the non-functionalized silica shows the low surface area (S{sub BET} = 40 m{sup 2} g{sup −1}). The BJH analysis showed that PVP can be used as an effective agent to increase an average pore size and total pore volume. The results indicate that PVP functionalized silicas show a potential as effective adsorbents for bilirubin removal compared to other available adsorbents. - Highlights: • PVP functionalized silicas were synthesized via sol–gel method. • Modification of silica by PVP leads to the formation of mesoporous structure. • PVP functionalized mesoporous silicas demonstrate good adsorption properties for bilirubin removal.

  3. The preparation, surface structure, zeta potential, surface charge density and photocatalytic activity of TiO2 nanostructures of different shapes

    Science.gov (United States)

    Grover, Inderpreet Singh; Singh, Satnam; Pal, Bonamali

    2013-09-01

    Titania based nanocatalysts such as sodium titanates of different morphology having superior surface properties are getting wide importance in photocatalysis research. Despite having sodium (Na) contents and its high temperature synthesis (that generally deteriorate the photoreactivity), these Na-titanates often exhibit better photoactivity than P25-TiO2 catalyst. Hence, this work demonstrated the influence of crystal structure, BET surface area, surface charge, zeta potential (ζ) and metal loading on the photocatalytic activity of as-prepared sodium titanate nanotube (TNT) and titania nanorod (TNR). Straw like hollow orthorhombic-TNT (Na2Ti2O5·H2O) particles (W = 9-12 nm and L = 82-115 nm) and rice like pure anatase-TNR particles (W = 8-13 nm and L = 81-134 nm) are obtained by the hydrothermal treatment of P25-TiO2 with NaOH, which in fact, altered the net surface charge of TNT and TNR particles. The observed ζ = -2.82 (P25-TiO2), -13.5 (TNT) and -22.5 mV (TNR) are significantly altered by the Ag and Cu deposition. It has been found here that TNT displayed best photocatalytic activity for the imidacloprid insecticide (C9H10ClN5O2) degradation to CO2 formation under UV irradiation because of its largest surface area 176 m2 g-1 among the catalysts studied.

  4. Defective ZnCo2O4 with Zn vacancies: Synthesis, property and electrochemical application

    DEFF Research Database (Denmark)

    Huang, Guoyong; Yang, Yue; Sun, Hongyu

    2017-01-01

    Through the liquid-phase co-precipitation and alkaline-tailored method, the defective ZnCo2O4 with Zn vacancies (Zn0.95Co2O4) has been synthesized, which is similar to the crystal phase, morphology, and particle size of the pure ZnCo2O4 before etched, except the enlarged BET specific surface. For...

  5. Specific surface area behavior of a dissolving population of particles. Augmenting Mercer Dissolution Theory

    International Nuclear Information System (INIS)

    Scripsick, R.C.; Rothenberg, S.J.

    1986-01-01

    Specific surface area (Sp) measurements were made on two uranium oxide aerosol materials before and after in vitro dissolution studies were performed on the materials. The results of these Sp measurements were evaluated relative to predictions made from extending Mercer dissolution theory to describe the Sp behavior of a dissolving population of particles

  6. Rangeland Brush Estimation Toolbox (RaBET): An Approach for Evaluating Brush Management Conservation Efforts in Western Grazing Lands

    Science.gov (United States)

    Holifield Collins, C.; Kautz, M. A.; Skirvin, S. M.; Metz, L. J.

    2016-12-01

    There are over 180 million hectares of rangelands and grazed forests in the central and western United States. Due to the loss of perennial grasses and subsequent increased runoff and erosion that can degrade the system, woody cover species cannot be allowed to proliferate unchecked. The USDA-Natural Resources Conservation Service (NRCS) has allocated extensive resources to employ brush management (removal) as a conservation practice to control woody species encroachment. The Rangeland-Conservation Effects Assessment Project (CEAP) has been tasked with determining how effective the practice has been, however their land managers lack a cost-effective means to conduct these assessments at the necessary scale. An ArcGIS toolbox for generating large-scale, Landsat-based, spatial maps of woody cover on grazing lands in the western United States was developed through a collaboration with NRCS Rangeland-CEAP. The toolbox contains two main components of operation, image generation and temporal analysis, and utilizes simple interfaces requiring minimum user inputs. The image generation tool utilizes geographically specific algorithms developed from combining moderate-resolution (30-m) Landsat imagery and high-resolution (1-m) National Agricultural Imagery Program (NAIP) aerial photography to produce the woody cover scenes at the Major Land Resource (MLRA) scale. The temporal analysis tool can be used on these scenes to assess treatment effectiveness and monitor woody cover reemergence. RaBET provides rangeland managers an operational, inexpensive decision support tool to aid in the application of brush removal treatments and assessing their effectiveness.

  7. Surface mesh to voxel data registration for patient-specific anatomical modeling

    Science.gov (United States)

    de Oliveira, Júlia E. E.; Giessler, Paul; Keszei, András.; Herrler, Andreas; Deserno, Thomas M.

    2016-03-01

    Virtual Physiological Human (VPH) models are frequently used for training, planning, and performing medical procedures. The Regional Anaesthesia Simulator and Assistant (RASimAs) project has the goal of increasing the application and effectiveness of regional anesthesia (RA) by combining a simulator of ultrasound-guided and electrical nerve-stimulated RA procedures and a subject-specific assistance system through an integration of image processing, physiological models, subject-specific data, and virtual reality. Individualized models enrich the virtual training tools for learning and improving regional anaesthesia (RA) skills. Therefore, we suggest patient-specific VPH models that are composed by registering the general mesh-based models with patient voxel data-based recordings. Specifically, the pelvis region has been focused for the support of the femoral nerve block. The processing pipeline is composed of different freely available toolboxes such as MatLab, the open Simulation framework (SOFA), and MeshLab. The approach of Gilles is applied for mesh-to-voxel registration. Personalized VPH models include anatomical as well as mechanical properties of the tissues. Two commercial VPH models (Zygote and Anatomium) were used together with 34 MRI data sets. Results are presented for the skin surface and pelvic bones. Future work will extend the registration procedure to cope with all model tissue (i.e., skin, muscle, bone, vessel, nerve, fascia) in a one-step procedure and extrapolating the personalized models to body regions actually being out of the captured field of view.

  8. Activated carbon preparation with pore nanosized from biomass precursors; Preparacao de carvoes ativados com poros de dimensoes nanometricas a partir de precursores de biomassa

    Energy Technology Data Exchange (ETDEWEB)

    Capobianco, Gino [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Fac. de Engenharia Mecanica. Dept. de Planejamento de Sistemas Energeticos; Coutinho, Aparecido dos Reis [Universidade Metodista de Piracicaba, SP (Brazil). Lab. de Materiais Carbonosos; Luengo, Carlos Alberto [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Inst. de Fisica Gleb Wataghin. Grupo Combustiveis Alternativos

    2004-07-01

    Here are reported preliminary tests using pinnus wood, mesocarpo of green coconut and macadamia shell. They are carbonized and later physically activated with CO{sub 2} or chemically with ZnCl{sub 2}. The resulting activated carbons (AC) are characterized with scanning electronic microscopy, the BET method for determination of the specific surface area-ASE, real density-DR, helium picnometry among others. The results indicate macadamia shell originates better AC, with average micropores in the range of 1,2-1,6 nm, apparent density of 1,08 g/cm{sup 3}, and ASE-BET 1400m{sup 2}/g. Then, these AC have the possibility to be applied in NG storage. (author)

  9. Fabrication of mesoporous and high specific surface area lanthanum carbide-carbon nanotube composites

    International Nuclear Information System (INIS)

    Biasetto, L.; Carturan, S.; Maggioni, G.; Zanonato, P.; Bernardo, P. Di; Colombo, P.; Andrighetto, A.; Prete, G.

    2009-01-01

    Mesoporous lanthanum carbide-carbon nanotube composites were produced by means of carbothermal reaction of lanthanum oxide, graphite and multi-walled carbon nanotube mixtures under high vacuum. Residual gas analysis revealed the higher reactivity of lanthanum oxide towards carbon nanotubes compared to graphite. After sintering, the composites revealed a specific surface area increasing with the amount of carbon nanotubes introduced. The meso-porosity of carbon nanotubes was maintained after thermal treatment.

  10. Contribuição da adição de cinzas volantes para a melhoria da durabilidade do betão

    OpenAIRE

    Camões, Aires; Rocha, Patrício; Aguiar, J. L. Barroso de; Jalali, Said; Delgado, Raimundo

    2002-01-01

    Esta comunicação pretende demonstrar que recorrendo a materiais correntes e à substituição de cimento por cinzas volantes é possível produzir betões de elevado desempenho, sem prejuízo das suas características de durabilidade. Através da adição de cinzas volantes é possível reduzir significativamente o consumo de cimento e com a utilização de agregados britados, designadamente areias, contribuir para a preservação dos recursos naturais não renováveis existentes.

  11. An IgE epitope of Bet v 1 and fagales PR10 proteins as defined by a human monoclonal IgE

    DEFF Research Database (Denmark)

    Hecker, J.; Diethers, A.; Schulz, D.

    2012-01-01

    -reactivities predicted by primary structure analyses of different isoforms and PR10 proteins were verified by allergen chip-based analyses. CONCLUSIONS: The obtained results demonstrate that hybrid IgE repertoires represent a source for human antibodies with genuine paratopes. The IgE-derived information about the Ig...... generation and epitope delineation of a human monoclonal IgE against the prototypic allergen Bet v 1. METHODS: Phage-display scFv hybrid libraries of allergic donor-derived VH epsilon and synthetic VL were established from 107 mononuclear cells. An obtained scFv was converted into human immunoglobulin...

  12. Discussion about the use of the volume specific surface area (VSSA) as a criterion to identify nanomaterials according to the EU definition. Part two: experimental approach.

    Science.gov (United States)

    Lecloux, André J; Atluri, Rambabu; Kolen'ko, Yury V; Deepak, Francis Leonard

    2017-10-12

    The first part of this study was dedicated to the modelling of the influence of particle shape, porosity and particle size distribution on the volume specific surface area (VSSA) values in order to check the applicability of this concept to the identification of nanomaterials according to the European Commission Recommendation. In this second part, experimental VSSA values are obtained for various samples from nitrogen adsorption isotherms and these values were used as a screening tool to identify and classify nanomaterials. These identification results are compared to the identification based on the 50% of particles with a size below 100 nm criterion applied to the experimental particle size distributions obtained by analysis of electron microscopy images on the same materials. It is concluded that the experimental VSSA values are able to identify nanomaterials, without false negative identification, if they have a mono-modal particle size, if the adsorption data cover the relative pressure range from 0.001 to 0.65 and if a simple, qualitative image of the particles by transmission or scanning electron microscopy is available to define their shape. The experimental conditions to obtain reliable adsorption data as well as the way to analyze the adsorption isotherms are described and discussed in some detail in order to help the reader in using the experimental VSSA criterion. To obtain the experimental VSSA values, the BET surface area can be used for non-porous particles, but for porous, nanostructured or coated nanoparticles, only the external surface of the particles, obtained by a modified t-plot approach, should be considered to determine the experimental VSSA and to avoid false positive identification of nanomaterials, only the external surface area being related to the particle size. Finally, the availability of experimental VSSA values together with particle size distributions obtained by electron microscopy gave the opportunity to check the

  13. Standard Specification for Steel Blades Used with the Photovoltaic Module Surface Cut Test

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2009-01-01

    1.1 This specification specifies the recommended physical characteristics of the steel blades required for the surface cut test described in ANSI/UL 1703 (Section 24) and IEC 61730-2 (Paragraph 10.3). 1.2 ANSI/UL 1703 and IEC 61730-2 are standards for photovoltaic module safety testing. 1.3 This standard provides additional fabrication details for the surface cut test blades that are not provided in ANSI/UL 1703 or IEC 61730-2. Surface cut test blades that have out-of-tolerance corner radii or burrs are known to cause erroneous test results, either passes or failures. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  14. Characterization of Ce0.9Gd0.1O1.95 powders synthesized by spray drying

    DEFF Research Database (Denmark)

    Blennow Tullmar, Peter; Chen, Weiwu; Lundberg, Mats

    2009-01-01

    Ce0.9Gd0.1O1.95 powders were synthesized by spray drying and successive calcinations. The phase purity, BET surface area, and particle morphology of as-sprayed and calcined powders were characterized. After calcination above 300 °C, the powders were single phase and showed a BET surface area of 68...

  15. Morphological Specifications of the Bird Schistosome Cercariae and Surface Carbohydrates as Receptors for Lectins

    Directory of Open Access Journals (Sweden)

    I Moebedi

    2007-04-01

    Full Text Available Background: To determine the morphological specifications of the bird schistosomes cercaria from Lymnaea gedrosiana and to detect the surface carbohydrates as receptors for host lectins in the host-parasite relationship systems such as avian schistosomiasis and human cercarial dermatitis. Methods: One hundred ninety two snails collected from Dezful areas in Khuzestan Province, in the south west of Iran, during 2005-2006 were examined for cercariae using shedding and crushing methods. In addition, surface carbohydrates on the cercariae were detected by lentil (Lens culinaris lectins. Results: From the total number of Lymnaea gedrosiana, which examined for bird schistosomes cercaria, 9(4% snails were found to be infected with furcocercus cercaria of the bird schistosomes (probably Gigantobilharzia sp.. Mannose monosaccharide CH2OH (CHOH4CHO as surface carbohydrate was also detected on the cercariae. Conclusion: Mannose carbohydrate on these cercariae may be used as receptor by lectins.

  16. Dynamic characterisation of the specific surface area for fracture networks

    Science.gov (United States)

    Cvetkovic, V.

    2017-12-01

    One important application of chemical transport is geological disposal of high-level nuclear waste for which crystalline rock is a prime candidate for instance in Scandinavia. Interconnected heterogeneous fractures of sparsely fractured rock such as granite, act as conduits for transport of dissolved tracers. Fluid flow is known to be highly channelized in such rocks. Channels imply narrow flow paths, adjacent to essentially stagnant water in the fracture and/or the rock matrix. Tracers are transported along channelised flow paths and retained by minerals and/or stagnant water, depending on their sorption properties; this mechanism is critical for rocks to act as a barrier and ultimately provide safety for a geological repository. The sorbing tracers are retained by diffusion and sorption on mineral surfaces, whereas non-sorbing tracers can be retained only by diffusion into stagnant water of fractures. The retention and transport properties of a sparsely fractured rock will primarily depend on the specific surface area (SSA) of the fracture network which is determined by the heterogeneous structure and flow. The main challenge when characterising SSA on the field-scale is its dependence on the flow dynamics. We first define SSA as a physical quantity and clarify its importance for chemical transport. A methodology for dynamic characterisation of SSA in fracture networks is proposed that relies on three sets of data: i) Flow rate data as obtained by a flow logging procedure; ii) transmissivity data as obtained by pumping tests; iii) fracture network data as obtained from outcrop and geophysical observations. The proposed methodology utilises these data directly as well as indirectly through flow and particle tracking simulations in three-dimensional discrete fracture networks. The methodology is exemplified using specific data from the Swedish site Laxemar. The potential impact of uncertainties is of particular significance and is illustrated for radionuclide

  17. Interfacial Interaction in Anodic Aluminum Oxide Templates Modifies Morphology, Surface Area, and Crystallization of Polyamide-6 Nanofibers.

    Science.gov (United States)

    Xue, Junhui; Xu, Yizhuang; Jin, Zhaoxia

    2016-03-08

    Here, we demonstrated that, when the precipitation process of polyamide-6 (PA6) solution happens in cylindrical channels of an anodized aluminum oxide membrane (AAO), interface interactions between a solid surface, solvent, non-solvent, and PA6 will influence the obtained polymer nanostructures, resulting in complex morphologies, increased surface area, and crystallization changes. With the enhancing interaction of PA6 and the AAO surface, the morphology of PA6 nanostructures changes from solid nanofibers, mesoporous, to bamboo-like, while at the same time, metastable γ-phase domains increase in these PA6 nanostructures. Brunauer-Emmett-Teller (BET) surface areas of solid, bamboo-like, and mesoporous PA6 nanofibers rise from 16, 20.9, to 25 m(2)/g. This study shows that interfacial interaction in AAO template fabrication can be used in manipulating the morphology and crystallization of one-dimensional polymer nanostructures. It also provides us a simple and novel method to create porous PA6 nanofibers with a large surface area.

  18. Inhibition of bromodomain and extra-terminal (BET) proteins increases NKG2D ligand MICA expression and sensitivity to NK cell-mediated cytotoxicity in multiple myeloma cells: role of cMYC-IRF4-miR-125b interplay.

    Science.gov (United States)

    Abruzzese, Maria Pia; Bilotta, Maria Teresa; Fionda, Cinzia; Zingoni, Alessandra; Soriani, Alessandra; Vulpis, Elisabetta; Borrelli, Cristiana; Zitti, Beatrice; Petrucci, Maria Teresa; Ricciardi, Maria Rosaria; Molfetta, Rosa; Paolini, Rossella; Santoni, Angela; Cippitelli, Marco

    2016-12-01

    Anti-cancer immune responses may contribute to the control of tumors after conventional chemotherapy, and different observations have indicated that chemotherapeutic agents can induce immune responses resulting in cancer cell death and immune-stimulatory side effects. Increasing experimental and clinical evidence highlight the importance of natural killer (NK) cells in immune responses toward multiple myeloma (MM), and combination therapies able to enhance the activity of NK cells against MM are showing promise in treating this hematologic cancer. The epigenetic readers of acetylated histones bromodomain and extra-terminal (BET) proteins are critical regulators of gene expression. In cancer, they can upregulate transcription of key oncogenes such as cMYC, IRF4, and BCL-2. In addition, the activity of these proteins can regulate the expression of osteoclastogenic cytokines during cancer progression. Here, we investigated the effect of BET bromodomain protein inhibition, on the expression of NK cell-activating ligands in MM cells. Five MM cell lines [SKO-007(J3), U266, RPMI-8226, ARP-1, JJN3] and CD138 + MM cells isolated from MM patients were used to investigate the activity of BET bromodomain inhibitors (BETi) (JQ1 and I-BET151) and of the selective BRD4-degrader proteolysis targeting chimera (PROTAC) (ARV-825), on the expression and function of several NK cell-activating ligands (NKG2DLs and DNAM-1Ls), using flow cytometry, real-time PCR, transient transfections, and degranulation assays. Our results indicate that inhibition of BET proteins via small molecule inhibitors or their degradation via a hetero-bifunctional PROTAC probe can enhance the expression of MICA, a ligand of the NKG2D receptor, in human MM cell lines and primary malignant plasma cells, rendering myeloma cells more efficient to activate NK cell degranulation. Noteworthy, similar results were obtained using selective CBP/EP300 bromodomain inhibition. Mechanistically, we found that BETi

  19. Resistance to BET Inhibitor Leads to Alternative Therapeutic Vulnerabilities in Castration-Resistant Prostate Cancer.

    Science.gov (United States)

    Pawar, Aishwarya; Gollavilli, Paradesi Naidu; Wang, Shaomeng; Asangani, Irfan A

    2018-02-27

    BRD4 plays a major role in the transcription networks orchestrated by androgen receptor (AR) in castration-resistant prostate cancer (CRPC). Several BET inhibitors (BETi) that displace BRD4 from chromatin are being evaluated in clinical trials for CRPC. Here, we describe mechanisms of acquired resistance to BETi that are amenable to targeted therapies in CRPC. BETi-resistant CRPC cells displayed cross-resistance to a variety of BETi in the absence of gatekeeper mutations, exhibited reduced chromatin-bound BRD4, and were less sensitive to BRD4 degraders/knockdown, suggesting a BRD4-independent transcription program. Transcriptomic analysis revealed reactivation of AR signaling due to CDK9-mediated phosphorylation of AR, resulting in sensitivity to CDK9 inhibitors and enzalutamide. Additionally, increased DNA damage associated with PRC2-mediated transcriptional silencing of DDR genes was observed, leading to PARP inhibitor sensitivity. Collectively, our results identify the therapeutic limitation of BETi as a monotherapy; however, our BETi resistance data suggest unique opportunities for combination therapies in treating CRPC. Copyright © 2018 The Author(s). Published by Elsevier Inc. All rights reserved.

  20. Enhancement of the surface methane hydrate-bearing layer based on the specific microorganisms form deep seabed sediment in Japan Sea.

    Science.gov (United States)

    Hata, T.; Yoneda, J.; Yamamoto, K.

    2017-12-01

    A methane hydrate-bearing layer located near the Japan Sea has been investigated as a new potential energy resource. In this study examined the feasibility of the seabed surface sediment strength located in the Japan Sea improvement technologies for enhancing microbial induced carbonate precipitation (MICP) process. First, the authors cultivated the specific urease production bacterium culture medium from this surface methane hydrate-bearing layer in the seabed (-600m depth) of Japan Sea. After that, two types of the laboratory test (consolidated-drained triaxial tests) were conducted using this specific culture medium from the seabed in the Japan Sea near the Toyama Prefecture and high urease activities bacterium named Bacillus pasteurii. The main outcomes of this research are as follows. 1) Specific culture medium focused on the urease production bacterium can enhancement of the urease activities from the methane hydrate-bearing layer near the Japan Sea side, 2) This specific culture medium can be enhancement of the surface layer strength, 3) The microbial induced carbonate precipitation process can increase the particle size compared to that of the original particles coating the calcite layer surface, 4) The mechanism for increasing the soil strength is based on the addition of cohesion like a cement stabilized soil.

  1. Heteroatom Polymer-Derived 3D High-Surface-Area and Mesoporous Graphene Sheet-Like Carbon for Supercapacitors.

    Science.gov (United States)

    Sheng, Haiyang; Wei, Min; D'Aloia, Alyssa; Wu, Gang

    2016-11-09

    Current supercapacitors suffer from low energy density mainly due to the high degree of microporosity and insufficient hydrophilicity of their carbon electrodes. Development of a supercapacitor capable of simultaneously storing as much energy as a battery, along with providing sufficient power and long cycle stability would be valued for energy storage applications and innovations. Differing from commonly studied reduced graphene oxides, in this work we identified an inexpensive heteroatom polymer (polyaniline-PANI) as a carbon/nitrogen precursor, and applied a controlled thermal treatment at elevated temperature to convert PANI into 3D high-surface-area graphene-sheet-like carbon materials. During the carbonization process, various transition metals including Fe, Co, and Ni were added, which play critical roles in both catalyzing the graphitization and serving as pore forming agents. Factors including post-treatments, heating temperatures, and types of metal were found crucial for achieving enhanced capacitance performance on resulting carbon materials. Using FeCl 3 as precursor along with optimal heating temperature 1000 °C and mixed acid treatment (HCl+HNO 3 ), the highest Brunauer-Emmett-Teller (BET) surface area of 1645 m 2 g -1 was achieved on the mesopore dominant graphene-sheet-like carbon materials. The unique morphologies featured with high-surface areas, dominant mesopores, proper nitrogen doping, and 3D graphene-like structures correspond to remarkably enhanced electrochemical specific capacitance up to 478 Fg -1 in 1.0 M KOH at a scan rate of 5 mV s -1 . Furthermore, in a real two-electrode system of a symmetric supercapacitor, a specific capacitance of 235 Fg -1 using Nafion binder is obtained under a current density of 1 Ag -1 by galvanostatic charge-discharge tests in 6.0 M KOH. Long-term cycle stability up to 5000 cycles by using PVDF binder in electrode was systematically evaluated as a function of types of metals and current densities.

  2. Specific surface to evaluate the efficiencies of milling and pretreatment of wood for enzymatic saccharification

    Science.gov (United States)

    Junyong Zhu; G.S. Wang; X.J. Pan; Roland Gleisner

    2009-01-01

    Sieving methods have been almost exclusively used for feedstock size-reduction characterization in the biomass refining literature. This study demonstrates a methodology to properly characterize specific surface of biomass substrates through two dimensional measurement of each fiber of the substrate using a wet imaging technique. The methodology provides more...

  3. Changes in cell surface structure by viral transformation studied by binding of lectins differing in sugar specificity.

    Science.gov (United States)

    Tsuda, M; Kurokawa, T; Takeuchi, M; Sugino, Y

    1975-10-01

    Changes in cell surface structure by viral transformation were studied by examining changes in the binding of various lectins differing in carbohydrate specificities. Binding of lectins was assayed directly using cells grown in coverslips. The following 125I-lectins were used: Concanavalin-A (specific for glucose and mannose), wheat germ agglutinin (specific for N-acetylglucosamine), castor bean agglutinin (specific for galactose), Wistaria floribunda agglutinin (specific for N-acetylgalactosamine), and soybean agglutinin (specific for N-acetyl-galactosamine). Cells for a clone, SS7, transformed by bovine adenovirus type-3, were found to bind 5 to 6 times more Wistaria floribunda agglutinin than the normal counterpart cells (clone C31, from C3H mouse kidney). In contrast, the binding of soybean agglutinin, which has a sugar specificity similar to Wistaria floribunda agglutinin, to normal and transformed cells was similar. The binding of wheat germ agglutinin and castor bean agglutinin, respectively, to normal and transformed cells was also similar. However, normal cells bound twice as much concanavalin-A as transformed cells. Only half as much Wistaria floribunda agglutinin was bound to transformed cells when they had been dispersed with EDTA. These changes in the number of lectin binding sites on transformation are thought to reflect alteration of the cell surface structure. The amount of lectins bound per cell decreased with increase in cell density, especially in the case of binding of Wistaria floribunda agglutinin to normal cells.

  4. Amino acid specificity of fibers of the facial/trigeminal complex innervating the maxillary barbel in the Japanese sea catfish, Plotosus japonicus.

    Science.gov (United States)

    Caprio, John; Shimohara, Mami; Marui, Takayuki; Kohbara, Jun; Harada, Shuitsu; Kiyohara, Sadao

    2015-12-01

    The Japanese sea catfish, Plotosus japonicus, possesses taste and solitary chemoreceptor cells (SCCs) located on the external body surface that detect specific water-soluble substances. Here, we identify two major fiber types of the facial/trigeminal complex that transmit amino acid information to the medulla. Both single and few fiber preparations respond to amino acid stimulation in the 0.1 μM to mM range. One fiber type responds best to glycine and l-alanine (i.e. Gly/Ala fibers) whereas the other fiber type is best stimulated by l-proline and glycine betaine (hereafter referred to only as betaine) (i.e. Pro/Bet fibers). We demonstrate that betaine, which does not alter the pH of the seawater and therefore does not activate the animals' highly sensitive pH sensors (Caprio et al., Science 344:1154-1156, 2014), is sufficient to elicit appetitive food search behavior. We further show that the amino acid specificity of fibers of the facial/trigeminal complex in P. japonicus is different from that in Ariopsis felis (Michel and Caprio, J. Neurophysiol. 66:247-260, 1991; Michel et al., J. Comp. Physiol. A. 172:129-138, 1993), a representative member of the only other family (Ariidae) of extant marine catfishes. Copyright © 2015 Elsevier Inc. All rights reserved.

  5. Multiple containment for LSA [low specific activity] and SCO [surface contaminated objects] wastes

    International Nuclear Information System (INIS)

    Burgess, M.H.

    1993-09-01

    Radioactive wastes are generally transported in the form of Low Specific Activity (LSA) materials or Surface Contaminated Objects (SCO). This report proposes that a method of acknowledging the beneficial effects of multiple containment for such wastes should be written into the 1996 Edition of the IAEA Transport Regulations. Experience used to assess risks from on-site movements of radioactive material in the UK can be applied to develop safety arguments justifying the alleviation of off-site transport risks. (UK)

  6. Adsorption of cadmium by activated carbon cloth: influence of surface oxidation and solution pH.

    Science.gov (United States)

    Rangel-Mendez, J R; Streat, M

    2002-03-01

    The surface of activated carbon cloth (ACC), based on polyacrylonitrile fibre as a precursor, was oxidised using nitric acid, ozone and electrochemical oxidation to enhance cadmium ion exchange capacity. Modified adsorbents were physically and chemically characterised by pH titration, direct titration, X-ray photoelectron spectroscopy, elemental analysis, surface area and porosimetry, and scanning electron microscopy. BET surface area decreased after oxidation, however, the total ion exchange capacity increased by a factor of approximately 3.5 compared to the commercial as-received ACC. A very significant increase in cadmium uptake, by a factor of 13, was observed for the electrochemically oxidised ACC. Equilibrium sorption isotherms were determined at pH 4, 5 and 6 and these showed that cadmium uptake increased with increasing pH. There was clear evidence of physical damage to ozone-oxidised fibre, however, acid and electrochemically oxidised samples were completely stable.

  7. The specificity of targeted vaccines for APC surface molecules influences the immune response phenotype.

    Directory of Open Access Journals (Sweden)

    Gunnveig Grødeland

    Full Text Available Different diseases require different immune responses for efficient protection. Thus, prophylactic vaccines should prime the immune system for the particular type of response needed for protection against a given infectious agent. We have here tested fusion DNA vaccines which encode proteins that bivalently target influenza hemagglutinins (HA to different surface molecules on antigen presenting cells (APC. We demonstrate that targeting to MHC class II molecules predominantly induced an antibody/Th2 response, whereas targeting to CCR1/3/5 predominantly induced a CD8(+/Th1 T cell response. With respect to antibodies, the polarizing effect was even more pronounced upon intramuscular (i.m delivery as compared to intradermal (i.d. vaccination. Despite these differences in induced immune responses, both vaccines protected against a viral challenge with influenza H1N1. Substitution of HA with ovalbumin (OVA demonstrated that polarization of immune responses, as a consequence of APC targeting specificity, could be extended to other antigens. Taken together, the results demonstrate that vaccination can be tailor-made to induce a particular phenotype of adaptive immune responses by specifically targeting different surface molecules on APCs.

  8. 3-D surface reconstruction of patient specific anatomic data using a pre-specified number of polygons.

    Science.gov (United States)

    Aharon, S; Robb, R A

    1997-01-01

    Virtual reality environments provide highly interactive, natural control of the visualization process, significantly enhancing the scientific value of the data produced by medical imaging systems. Due to the computational and real time display update requirements of virtual reality interfaces, however, the complexity of organ and tissue surfaces which can be displayed is limited. In this paper, we present a new algorithm for the production of a polygonal surface containing a pre-specified number of polygons from patient or subject specific volumetric image data. The advantage of this new algorithm is that it effectively tiles complex structures with a specified number of polygons selected to optimize the trade-off between surface detail and real-time display rates.

  9. Molecular analysis of the role of osmolyte transporters opuCA and betL in Listeria monocytogenes after cold and freezing stress.

    Science.gov (United States)

    Miladi, Hanene; Elabed, Hamouda; Ben Slama, Rihab; Rhim, Amel; Bakhrouf, Amina

    2017-03-01

    Listeria monocytogenes is a food-borne pathogen of humans and other animals. The striking ability to survive several stresses usually used for food preservation makes L. monocytogenes one of the biggest concerns to the food industry. This ubiquity can be partly explained by the ability of the organism to grow and persist at very low temperatures, a consequence of its ability to accumulate cryoprotective compound called osmolytes. A quantitative RT-PCR assay was used to measure mRNA transcript accumulation for the stress response genes opuCA and betL (encoding carnitine and betaine transporters, respectively) and the housekeeping gene 16S rRNA. Assays were conducted on mid-exponential phase L. monocytogenes cells exposed to conditions reflecting cold and freezing stress, conditions usually used to preserve foods. We showed that expression of the two cold-adapted genes encoded the transporters of the cryoprotectants carnitine and betaine in ATCC 19115 and the food-isolated L. monocytogenes S1 is induced after cold and freezing stress exposure. Furthermore, transcriptional analysis of the genes encoding opuCA and betL revealed that each transporter is induced to different degrees upon cold shock of L. monocytogenes ATCC 19115 and S1. Our results confirm an increase in carnitine uptake at low temperatures more than in betaine after cold-shocked temperature compared to the non-stress control treatment. It was concluded the use of carnitine and betaine as cryoprotectants is essential for rapid induction of the tested stress response under conditions typically encountered during food preservation.

  10. Site-Specific Molecule-Surface Interactions on Metal Oxides

    National Research Council Canada - National Science Library

    Reisler, Hanna

    1998-01-01

    .... At low incident energies rotational and translational temperatures of scattered HCl were equal to the surface temperature, and residence times in the millisecond regime were observed at low surface temperature. When HCl(v=2, J=1...

  11. Preparation of lignin-based carbon aerogels as biomaterials for nano-supercapacitor

    Science.gov (United States)

    Yang, Bong Suk; Kang, Kyu-Young; Jeong, Myung-Joon

    2017-10-01

    Kraft and organosolv lignins, generally produced in chemical pulping and bio-refinery processes of lignocellulosic biomass, were used to prepare lignin-based carbon aerogels for supercapacitors as raw materials. The difference between lignins and lignin-based aerogels were compared by analyzing physical and chemical properties, including molecular weight, polydispersity, and reactivity with formaldehyde. Also, density, shrinkage, Brunauer-Emmett-Teller (BET) surface area and scanning electron microscope (SEM) images of the lignin-based aerogel were investigated. Kraft lignin consisting of coniferyl alcohol (G) and p-coumaryl alcohol (H) increased the reactivity of formaldehyde, formed a hydrogel well (porosity > 0.45), and specific surface area higher than organosolv lignin. In the case of kraft lignin, there were irregular changes such as oxidation and condensation in the pulping process. However, reaction sites with aromatic rings in lignin impacted the production of aerogel and required a long gelation period. The molecular weight of lignin influences the gelation time in producing lignin-based aerogel, and lignin composition affects the BET surface area and pore structures of the lignin-based carbon aerogels.

  12. Enhanced specific capacitance of modified needle cokes by controlling oxidation treatment

    International Nuclear Information System (INIS)

    Yang, Sunhye; Kim, Ick-Jun; Choi, In-Sik; Soo Kim, Hyun; Tack Kim, Yu

    2010-01-01

    The electric double-layer performance of needle cokes can be affected by the morphology of structures. Hence, we introduce modified needle cokes by using simple oxidation treatment. The degree of graphitization with high specific capacitance is controlled by acid and heat treatment. The active sites of cokes are increased with increasing oxidation time. Dilute nitric acid (HNO 3 ) and sodium chlorate (NaClO 3 ) are used for the activation of cokes. In this case, the interlayer distance is dramatically increased from 3.5 to 8.9 A. The specific capacitances are 33 F g -1 and 30 F ml -1 , respectively, on a two-electrode system with a potential range of 0-2.5 V. The behaviors of double-layer capacitance are demonstrated by the charge-discharge process and the morphologies of modified needle cokes are analyzed by XRD, FE-SEM, BET and elemental analysis.

  13. Preparation of Nano Activated γ-Alumina ( with Surfactant and Surface Characterization

    Directory of Open Access Journals (Sweden)

    Enas Sameer AL-Khawaja

    2016-09-01

    Full Text Available This paper deals with the preparation of Alumina by sol-gel technique through the hydrolysis of aluminum ion mixed with the glucose as a surfactant and converting it to gel by ammonium hydroxide in aqueous media. The resulting sol composed of particle is draying to become a transparent gel. The freshly prepared gel is heated at 700°C for 2hrs to obtain alumina ( particles. The obtained particles are found to be γ-alumina particles with high porosity, Their characteristics are determined by LPSA, XRD, SEM, TEM and BET techniques. The results show that the particles are pure alumina, nano-sized=20nm, spherical shape, high surface area=210 /gm.

  14. The preparation, surface structure, zeta potential, surface charge density and photocatalytic activity of TiO2 nanostructures of different shapes

    International Nuclear Information System (INIS)

    Grover, Inderpreet Singh; Singh, Satnam; Pal, Bonamali

    2013-01-01

    Titania based nanocatalysts such as sodium titanates of different morphology having superior surface properties are getting wide importance in photocatalysis research. Despite having sodium (Na) contents and its high temperature synthesis (that generally deteriorate the photoreactivity), these Na-titanates often exhibit better photoactivity than P25-TiO 2 catalyst. Hence, this work demonstrated the influence of crystal structure, BET surface area, surface charge, zeta potential (ζ) and metal loading on the photocatalytic activity of as-prepared sodium titanate nanotube (TNT) and titania nanorod (TNR). Straw like hollow orthorhombic-TNT (Na 2 Ti 2 O 5 ·H 2 O) particles (W = 9–12 nm and L = 82–115 nm) and rice like pure anatase-TNR particles (W = 8–13 nm and L = 81–134 nm) are obtained by the hydrothermal treatment of P25-TiO 2 with NaOH, which in fact, altered the net surface charge of TNT and TNR particles. The observed ζ = −2.82 (P25-TiO 2 ), −13.5 (TNT) and −22.5 mV (TNR) are significantly altered by the Ag and Cu deposition. It has been found here that TNT displayed best photocatalytic activity for the imidacloprid insecticide (C 9 H 10 ClN 5 O 2 ) degradation to CO 2 formation under UV irradiation because of its largest surface area 176 m 2 g −1 among the catalysts studied.

  15. Production of specific structured lipids by enzymatic interesterification: optimization of the reaction by response surface design

    DEFF Research Database (Denmark)

    Xu, Xuebing; Skands, Anja Rebecca Havegaard; Adler-Nissen, Jens

    1998-01-01

    Rapeseed oil and capric acid were interesterified in solvent-free media catalyzed by Lipozyme IM (Rhizomucor miehei) to produce specific-structured lipids (SSLs). The process was optimized by response surface design concerning the effects of acyl migration and the by-products of diacylglycerols...

  16. BET bromodomain inhibition as a novel strategy for reactivation of HIV-1.

    Science.gov (United States)

    Banerjee, Camellia; Archin, Nancie; Michaels, Daniel; Belkina, Anna C; Denis, Gerald V; Bradner, James; Sebastiani, Paola; Margolis, David M; Montano, Monty

    2012-12-01

    The persistence of latent HIV-1 remains a major challenge in therapeutic efforts to eradicate infection. We report the capacity for HIV reactivation by a selective small molecule inhibitor of BET family bromodomains, JQ1, a promising therapeutic agent with antioncogenic properties. JQ1 reactivated HIV transcription in models of latent T cell infection and latent monocyte infection. We also tested the effect of exposure to JQ1 to allow recovery of replication-competent HIV from pools of resting CD4(+) T cells isolated from HIV-infected, ART-treated patients. In one of three patients, JQ1 allowed recovery of virus at a frequency above unstimulated conditions. JQ1 potently suppressed T cell proliferation with minimal cytotoxic effect. Transcriptional profiling of T cells with JQ1 showed potent down-regulation of T cell activation genes, including CD3, CD28, and CXCR4, similar to HDAC inhibitors, but JQ1 also showed potent up-regulation of chromatin modification genes, including SIRT1, HDAC6, and multiple lysine demethylases (KDMs). Thus, JQ1 reactivates HIV-1 while suppressing T cell activation genes and up-regulating histone modification genes predicted to favor increased Tat activity. Thus, JQ1 may be useful in studies of potentially novel mechanisms for transcriptional control as well as in translational efforts to identify therapeutic molecules to achieve viral eradication.

  17. Functional Characterization of a Mucus-Specific LPXTG Surface Adhesin from Probiotic Lactobacillus rhamnosus GG ▿

    Science.gov (United States)

    von Ossowski, Ingemar; Satokari, Reetta; Reunanen, Justus; Lebeer, Sarah; De Keersmaecker, Sigrid C. J.; Vanderleyden, Jos; de Vos, Willem M.; Palva, Airi

    2011-01-01

    In spite of the wealth of clinical evidence supporting the health benefits of Lactobacillus rhamnosus GG in humans, there is still a lack of understanding of the molecular mechanisms behind its probiosis. Current knowledge suggests that the health-promoting effects of this probiotic strain might be partly dependent on its persistence in the intestine and adhesion to mucosal surfaces. Moreover, L. rhamnosus GG contains mucus-binding pili that might also explain the occupation of its ecological niche as a comparatively less stringent allochthonous intestine-dwelling bacterium. To uncover additional surface proteins involved in mucosal adhesion, we investigated the adherence properties of the only predicted protein (LGG_02337) in L. rhamnosus GG that exhibits homology with a known mucus-binding domain. We cloned a recombinant form of the gene for this putative mucus adhesin and established that the purified protein readily adheres to human intestinal mucus. We also showed that this mucus adhesin is visibly distributed throughout the cell surface and participates in the adhesive interaction between L. rhamnosus GG and mucus, although less prominently than the mucus-binding pili in this strain. Based on primary structural comparisons, we concluded that the current annotation of the LGG_02337 protein likely does not accurately reflect its predicted properties, and we propose that this mucus-specific adhesin be called the mucus-binding factor (MBF). Finally, we interpret our results to mean that L. rhamnosus GG MBF, as an active mucus-specific surface adhesin with a presumed ancillary involvement in pilus-mediated mucosal adhesion, plays a part in the adherent mechanisms during intestinal colonization by this probiotic. PMID:21602388

  18. Derivation of preliminary specifications for transmitted wavefront and surface roughness for large optics used in inertial confinement fusion

    International Nuclear Information System (INIS)

    Aikens, D.; Roussel, A.; Bray, M.

    1995-01-01

    In preparation for beginning the design of the Nation Ignition Facility (NIF) in the United States and the Laser Mega-Joule (LMJ) in France, the authors are in the process of deriving new specifications for the large optics required for these facilities. Traditionally, specifications for transmitted wavefront and surface roughness of large ICF optics have been based on parameters which were easily measured during the early 1980's, such as peak-to-valley wavefront error (PV) and root-mean-square (RMS) surface roughness, as well as wavefront gradients in terms of waves per cm. While this was convenient from a fabrication perspective, since the specifications could be easily interpreted by fabricators in terms which were understood and conventionally measurable, it did not accurately reflect the requirements of the laser system. For the NIF and LMJ laser systems, the authors use advances in metrology and interferometry and an enhanced understanding of laser system performance to derive specifications which are based on power spectral densities (PSD's.) Such requirements can more accurately reflect the requirements of the laser system for minimizing the amplitude of mid- and high-spatial frequency surface and transmitted wavefront errors, while not over constraining the fabrication in terms of low spatial frequencies, such as residual coma or astigmatism, which are typically of a very large amplitude compared to periodic errors. In order to study the effect of changes in individual component tolerances, it is most useful to have a model capable of simulating real behavior. The basis of this model is discussed in this paper, outlining the general approach to the open-quotes theoreticalclose quotes study of ICF optics specifications, and an indication of the type of specification to be expected will be shown, based upon existing ICF laser optics

  19. Top-down and bottom-up characterization of nitrated birch pollen allergen Bet v 1a with CZE hyphenated to an Orbitrap mass spectrometer.

    Science.gov (United States)

    Gusenkov, Sergey; Stutz, Hanno

    2018-02-01

    Tyrosine (Tyr) residues of the major pollen allergen of birch Betula verrucosa, Bet v 1a, were nitrated by peroxynitrite. This modification enhances the allergenicity. Modified tyrosines were identified by analyzing intact allergen variants in combination with top-down and bottom-up approaches. Therefore, a laboratory-built sheath-liquid assisted ESI interface was applied for hyphenation of CE to an Orbitrap mass spectrometer to localize individual nitration sites. The major focus was on identification of primary nitration sites. The top-down approach unambiguously identified Tyr 5 as the most prominent modification site. Fragments from the allergen core and the C-terminal part carried up to three potential nitration sites, respectively. Thus, a bottom-up approach with tryptic digest was used as a complementary strategy which allowed for the unambiguous localization of nitration sites within the respective peptides. Nitration propensity for individual Tyr residues was addressed by comparison of MS signals of nitrated peptides relative to all cognates of homolog primary sequence. Combined data identified surface exposed Tyr 5 and Tyr 66 as major nitration sites followed by less accessible Tyr 158 whereas Tyr 81, 83 and 150 possess a lower nitration tendency and are apparently modified in variants with higher nitration levels. © 2018 The Authors. Electrophoresis published by Wiley-VCH Verlag GmbH & Co. KGaA.

  20. Studies on Thermal Decomposition of Aluminium Sulfate to Produce Alumina Nano Structure

    Directory of Open Access Journals (Sweden)

    M. Jafar-Tafreshi

    2012-12-01

    Full Text Available Aluminum sulfate nano structures have been prepared by solution combustion synthesis using aluminum nitrate nonahydrate (Al(NO33.9H2O and ammonium sulfate ((NH42SO4. The resultant aluminum sulfate nano structures were calcined at different temperatures to study thermal  decomposition of aluminum sulfate. The crystallinity and phase of  the as-synthesized and calcined samples were characterized by both X- ray diffraction and FTIR measurements. These two analyses determined the temperature at which the aluminum sulfate is converted to γ-alumina nano particles. The specific surface area and pore size distribution for  γ-alumina nano particles were determined by BET measurement. TEM measurement confirmed the size of the particles obtained by XRD and BET analyses.

  1. Graphene-Like 2D Porous Carbon Nanosheets Derived from Cornstalk Pith for Energy Storage Materials

    Science.gov (United States)

    Gao, Kezheng; Niu, Qingyuan; Tang, Qiheng; Guo, Yaqing; Wang, Lizhen

    2018-01-01

    Biomass materials from different organisms or different parts (even different periods) of the same organism have different microscopic morphologies, hierarchical pore structures and even elemental compositions. Therefore, carbon materials inheriting the unique hierarchical microstructure of different biomass materials may exhibit significantly different electrochemical properties. Cornstalk pith and cornstalk skin (dried by freeze-drying) exhibit significantly different microstructures due to their different biological functions. The cornstalk skin-based carbon (S-carbon) exhibits a thick planar morphology, and the Barrett-Emmett-Teller (BET) surface area is only about 332.07 m2 g-1. However, cornstalk pith-based carbon (P-carbon) exhibits a graphene-like 2D porous nanosheet structure with a rough, wrinkled morphology, and the BET surface area is about 805.17 m2 g-1. In addition, a P-carbon supercapacitor exhibits much higher specific capacitance and much better rate capability than an S-carbon supercapacitor in 6 M potassium hydroxide (KOH) electrolyte.

  2. Trace Cd(II, Pb(II and Ni(II ions extraction and preconcentration from different water samples by using Ghezeljeh montmorillonite nanoclay as a natural new adsorbent

    Directory of Open Access Journals (Sweden)

    Zahra hassanzadeh Siahpoosh

    2017-01-01

    Full Text Available This investigate presents the extraction-preconcentration of Lead, Cadmium, and Nickel ions from water samples using Ghezeljeh montmorillonite nanoclay or “Geleh-Sar-Shoor” (means head-washing clay as a natural and native new adsorbent in batch single element systems. The Ghezeljeh clay is categorized by using Fourier Transform Infrared Spectroscopy (FT-IR, Scanning Electron Microscopy-Energy Dispersive Spectrometer Operating (SEM-EDS, X-ray Diffractometry (XRD, X-ray Fluorescence (XRF, Cation Exchange Capacity (CEC measurements, Surface property valuation (SBET by the BET method from nitrogen adsorption isotherms and Zeta potential. According to BET theory, the specific surface area of Ghezeljeh nanoclay was computed as 19.8 m2 g-1 whereas the cation exchange capacity was determined as 150 meq (100 g-1. The results of XRD, FT-IR, XRF, zeta potential, BET surface area and CEC of the Ghezeljeh clay confirm that montmorillonite is the dominant mineral phase. Based on SEM images of clay, it can be seen that the distance between the plates is nm level. For all three ions, the limit of detection, the limit of quantification, dynamic linear range, preconcentration factor, and the adsorption capacity were obtained. The result of several interfering ions was considered. The Ghezeljeh nanoclay as a new adsorbent and experimental method were effectively used for the extraction of heavy metals (Lead, Cadmium, and Nickel in a variety of real water samples.

  3. Synthesis of graphene aerogel for adsorption of bisphenol A

    Science.gov (United States)

    Trinh, Truong Thi Phuong Nguyet Xuan; Long, Nguyen Huynh Bach Son; Quang, Dong Thanh; Hieu, Nguyen Huu

    2018-04-01

    In this research, graphene aerogel (GA) was synthesized by chemical reduction method using ethylene diamine as a reducing agent. The morphology and properties of GA were characterized by calculating apparent density, Fourier transform infrared spectroscopy, X-ray diffraction, Raman spectroscopy, field emission scanning electron microscopy, and Brunauer-Emmett-Teller (BET) specific surface area. High-performance liquid chromatography (HPLC) was used to quantify the amount of the residual bisphenol A (BPA) concentration. The analysis results showed that GA exhibited low density ranging from 4-8 mg/cm3, hydrophobicity, high porosity, and specific surface area of 1883 m2/g according to BET. The obtained GA was used as an adsorbent for BPA. The effects of pH, contact time, and initial BPA concentration on the adsorption were investigated. The adsorption equilibrium time could be reached within 240 minutes. The adsorption data were well-fitted to pseudo-second-order kinetic equation and Langmuir isotherm model. The maximum adsorption capacity of GA for BPA calculated by the Langmuir model was 185.185 mg/g at pH 7. Accordingly, GA could be considered as promising adsorbents for BPA in water.

  4. Synthesis of zinc aluminate with high surface area by microwave hydrothermal method applied in the transesterification of soybean oil (biodiesel)

    Energy Technology Data Exchange (ETDEWEB)

    Quirino, M.R. [Chemistry Laboratory of Federal University of Paraiba (LABQUIM), Campus III, 58200-000 Bananeiras, PB (Brazil); Oliveira, M.J.C. [Academic Unit of Materials Engineering, UFCG, Campina Grande Campus I, 58429-900 Campina Grande, PB (Brazil); Keyson, D. [Laboratory of study in Science, DME, Federal University of Paraíba, Campus I, 58051-900 João Pessoa, PB (Brazil); Lucena, G.L., E-mail: guilherme_leo1@yahoo.com.br [Chemistry Laboratory of Federal University of Paraiba (LABQUIM), Campus III, 58200-000 Bananeiras, PB (Brazil); Oliveira, J.B.L. [Federal University of Rio Grande do Norte, UFRN, Campus I, 59078-970 Natal, RN (Brazil); Gama, L. [Academic Unit of Materials Engineering, UFCG, Campina Grande Campus I, 58429-900 Campina Grande, PB (Brazil)

    2016-02-15

    Highlights: • ZnAl{sub 2}O{sub 4} spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min. • The powders show high specific surface area. • ZAT{sub b}15 showed activity of 52.22% for the conversion of soybean oil into biodiesel. - Abstract: Zinc aluminate is a material with high thermal stability and high mechanical strength that, owing to these properties, is used as a catalyst or support. In this work, zinc aluminate spinel was synthesized by the microwave hydrothermal method in only 15 or 30 min at a low temperature (150 °C) without templates, using only Al(NO{sub 3}){sub 3}·9H{sub 2}O, Zn(NO{sub 3}){sub 2}·6H{sub 2}O, and urea as precursors and applied in the transesterification of soybean oil. X-ray diffraction analysis showed that ZnAl{sub 2}O{sub 4} had a cubic structure without secondary phases. The nitrogen adsorption measurements (BET) revealed a high surface area (266.57 m{sup 2} g{sup −1}) for the nanopowder synthesized in 15 min. This powder showed activity of 52.22% for the catalytic conversion of soybean oil into biodiesel by transesterification.

  5. Preparation of High Surface Area Activated Carbon from Spent Phenolic Resin by Microwave Heating and KOH Activation

    Science.gov (United States)

    Cheng, Song; Zhang, Libo; Zhang, Shengzhou; Xia, Hongying; Peng, Jinhui

    2018-01-01

    The spent phenolic resin is as raw material for preparing high surface area activated carbon (HSAAC) by microwave-assisted KOH activation. The effects of microwave power, activation duration and impregnation ratio (IR) on the iodine adsorption capability and yield of HSAAC were investigated. The surface characteristics of HSAAC were characterized by nitrogen adsorption isotherms, FTIR, SEM and TEM. The operating variables were optimized utilizing the response surface methodology (RSM) and were identified to be microwave power of 700 W, activation duration of 15 min and IR of 4, corresponding to a yield of 51.25 % and an iodine number of 2,384 mg/g. The pore structure parameters of the HSAAC, i. e., Brunauer-Emmett-Teller (BET) surface area, total pore volume, and average pore diameter were estimated to be 4,269 m2/g, 2.396 ml/g and 2.25 nm, respectively, under optimum conditions. The findings strongly support the feasibility of microwave-assisted KOH activation for preparation of HSAAC from spent phenolic resin.

  6. Concatenation of electrochemical grafting with chemical or electrochemical modification for preparing electrodes with specific surface functionality

    International Nuclear Information System (INIS)

    Verma, Pallavi; Maire, Pascal; Novak, Petr

    2011-01-01

    Surface modified electrodes are used in electro-analysis, electro-catalysis, sensors, biomedical applications, etc. and could also be used in batteries. The properties of modified electrodes are determined by the surface functionality. Therefore, the steps involved in the surface modification of the electrodes to obtain specific functionality are of prime importance. We illustrate here bridging of two routes of surface modifications namely electrochemical grafting, and chemical or electrochemical reduction. First, by electrochemical grafting an organic moiety is covalently immobilized on the surface. Then, either by chemical or by electrochemical route the terminal functional group of the grafted moiety is transformed. Using the former route we prepared lithium alkyl carbonate (-O(CH 2 ) 3 OCO 2 Li) modified carbon with potential applications in batteries, and employing the latter we prepared phenyl hydroxyl amine (-C 6 H 4 NHOH) modified carbon which may find application in biosensors. Benzyl alcohol (-C 6 H 4 CH 2 OH) modified carbon was prepared by both chemical as well as electrochemical route. We report combinations of conjugating the two steps of surface modifications and show how the optimal route of terminal functional group modification depends on the chemical nature of the moiety attached to the surface in the electrochemical grafting step.

  7. Concatenation of electrochemical grafting with chemical or electrochemical modification for preparing electrodes with specific surface functionality

    Energy Technology Data Exchange (ETDEWEB)

    Verma, Pallavi; Maire, Pascal [Paul Scherrer Institut, Electrochemistry Laboratory, Section Electrochemical Energy Storage, CH-5232 Villigen PSI (Switzerland); Novak, Petr, E-mail: petr.novak@psi.c [Paul Scherrer Institut, Electrochemistry Laboratory, Section Electrochemical Energy Storage, CH-5232 Villigen PSI (Switzerland)

    2011-04-01

    Surface modified electrodes are used in electro-analysis, electro-catalysis, sensors, biomedical applications, etc. and could also be used in batteries. The properties of modified electrodes are determined by the surface functionality. Therefore, the steps involved in the surface modification of the electrodes to obtain specific functionality are of prime importance. We illustrate here bridging of two routes of surface modifications namely electrochemical grafting, and chemical or electrochemical reduction. First, by electrochemical grafting an organic moiety is covalently immobilized on the surface. Then, either by chemical or by electrochemical route the terminal functional group of the grafted moiety is transformed. Using the former route we prepared lithium alkyl carbonate (-O(CH{sub 2}){sub 3}OCO{sub 2}Li) modified carbon with potential applications in batteries, and employing the latter we prepared phenyl hydroxyl amine (-C{sub 6}H{sub 4}NHOH) modified carbon which may find application in biosensors. Benzyl alcohol (-C{sub 6}H{sub 4}CH{sub 2}OH) modified carbon was prepared by both chemical as well as electrochemical route. We report combinations of conjugating the two steps of surface modifications and show how the optimal route of terminal functional group modification depends on the chemical nature of the moiety attached to the surface in the electrochemical grafting step.

  8. Polysiloxane surface modified with bipyrazolic tripodal receptor for quantitative lead adsorption

    Energy Technology Data Exchange (ETDEWEB)

    Radi, Smaail, E-mail: radi_smaail@yahoo.fr [Laboratoire de Chimie Organique, Macromoleculaire et Produits Naturels, Equipe de Chimie Bio-organique et Macromoleculaire, Unite Associee au CNRST URAC 25, Departement de Chimie, Faculte des Sciences, Universite Med I, BP 524, 60 000 Oujda (Morocco); Tighadouini, Said; Toubi, Yahya [Laboratoire de Chimie Organique, Macromoleculaire et Produits Naturels, Equipe de Chimie Bio-organique et Macromoleculaire, Unite Associee au CNRST URAC 25, Departement de Chimie, Faculte des Sciences, Universite Med I, BP 524, 60 000 Oujda (Morocco); Bacquet, Maryse [Universite des Sciences et Technologies de Lille, UMET: Unite Materiaux et Transformations UMR8207, Equipe Ingenierie des Systemes Polymeres, Batiment C6 salle 119-59655 Villeneuve d' Ascq (France)

    2011-01-15

    A new silica gel compound modified N,N-bis(3,5-dimethylpyrazol-1-ylmethyl) amine (SiN{sub 2}Pz) was synthesized and characterized by elemental analysis, FT-IR, {sup 13}C NMR of the solid state, nitrogen adsorption-desorption isotherm, BET surface area and BJH pore sizes. The new surface exhibits good chemical and thermal stability determined by thermogravimetry curves (TGA). The effect of pH and stirring time on the adsorption of Pb(II) were studied. The process of metal retention was followed by batch method and the optimum pH value for the quantitative adsorption of this toxic metal ion was 7. At this pH value, the new functionalized polysiloxane presents further improvements and shows higher affinity (123 mg of Pb{sup 2+}/g of silica) for the effective adsorption of Pb(II) compared to others described sorbents. The extracted amounts of Pb(II) were determined by atomic absorption measurements.

  9. Optimization of operating variables for production of ultra-fine talc in a stirred mill. Specific surface area investigations

    Directory of Open Access Journals (Sweden)

    Toraman Oner Yusuf

    2016-01-01

    Full Text Available Due to its properties such as chemical inertness, softness, whiteness, high thermal conductivity, low electrical conductivity and adsorption properties talc has wide industrial applications in paper, cosmetics, paints, polymer, ceramics, refractory materials and pharmaceutical. The demand for ultra-fine talc is emerging which drives the mineral industry to produce value added products. In this study, it was investigated how certain grinding parameters such as mill speed, ball filling ratio, powder filling ratio and grinding time of dry stirred mill affect grindability of talc ore (d97=127 μm. A series of laboratory experiments using a 24 full factorial design was conducted to determine the optimal operational parameters of a stirred mill in order to minimize the specific surface area. The main and interaction effects on the volume specific surface area (SV, m2.cm−3 of the ground product were evaluated using the Yates analysis. Under the optimal conditions at the stirrer speed of 600 rpm, grinding time of 20 min, sample mass of 5% and ball ratio of 70%, the resulting talc powder had larger volume specific surface area (i.e., 3.48 m2.cm−3 than the starting material (i.e., 1.84 m2.cm−3.

  10. Lar Betânia: O atendimento à infância abandonada em Maringá – PR

    Directory of Open Access Journals (Sweden)

    Ângela Mara de Barros Lara

    2012-08-01

    Full Text Available O presente artigo discute as políticas públicas de atendimento à criança e ao adolescenteem situação social de risco, na cidade de Maringá-PR, por meio da história do Lar Betânia,um abrigo fundado em 1965, no sistema casa-lar. A instituição que, em muitos períodos desua história chegou a atender, simultaneamente, 100 crianças vive hoje, a possibilidade desucumbir diante da atual filosofia do Estado de priorizar a permanência do menor junto àfamília biológica e, na impossibilidade dessa convivência, encaminhá-lo para acolhimento,junto às famílias cadastradas e preparadas para atuarem como famílias temporárias. Estadiscussão só foi possível a partir do estudo dos pressupostos que evidenciam o papel doEstado e dos direitos sociais na sociedade em que vivemos.

  11. Estimation of Specific Surface Area using Langmuir Isotherm ...

    African Journals Online (AJOL)

    Michael Horsfall

    Y= KCe/(1+KCe) (1) where Y is the fraction of fish carbon surface covered ..... transmigration of adsorbate in the plane surface. (Hameed et al., 2006). ... and to the Technologists of Agric Soil Science. Laboratory of ... Biosorption of Heavy Metals by Activated. Sludge and their Desorption Characteristics. J. Environ Mgt. 84: ...

  12. Drop drying on surfaces determines chemical reactivity - the specific case of immobilization of oligonucleotides on microarrays

    Science.gov (United States)

    2013-01-01

    Background Drop drying is a key factor in a wide range of technical applications, including spotted microarrays. The applied nL liquid volume provides specific reaction conditions for the immobilization of probe molecules to a chemically modified surface. Results We investigated the influence of nL and μL liquid drop volumes on the process of probe immobilization and compare the results obtained to the situation in liquid solution. In our data, we observe a strong relationship between drop drying effects on immobilization and surface chemistry. In this work, we present results on the immobilization of dye labeled 20mer oligonucleotides with and without an activating 5′-aminoheptyl linker onto a 2D epoxysilane and a 3D NHS activated hydrogel surface. Conclusions Our experiments identified two basic processes determining immobilization. First, the rate of drop drying that depends on the drop volume and the ambient relative humidity. Oligonucleotides in a dried spot react unspecifically with the surface and long reaction times are needed. 3D hydrogel surfaces allow for immobilization in a liquid environment under diffusive conditions. Here, oligonucleotide immobilization is much faster and a specific reaction with the reactive linker group is observed. Second, the effect of increasing probe concentration as a result of drop drying. On a 3D hydrogel, the increasing concentration of probe molecules in nL spotting volumes accelerates immobilization dramatically. In case of μL volumes, immobilization depends on whether the drop is allowed to dry completely. At non-drying conditions, very limited immobilization is observed due to the low oligonucleotide concentration used in microarray spotting solutions. The results of our study provide a general guideline for microarray assay development. They allow for the initial definition and further optimization of reaction conditions for the immobilization of oligonucleotides and other probe molecule classes to different

  13. Porphyromonas gingivalis Uses Specific Domain Rearrangements and Allelic Exchange to Generate Diversity in Surface Virulence Factors.

    Science.gov (United States)

    Dashper, Stuart G; Mitchell, Helen L; Seers, Christine A; Gladman, Simon L; Seemann, Torsten; Bulach, Dieter M; Chandry, P Scott; Cross, Keith J; Cleal, Steven M; Reynolds, Eric C

    2017-01-01

    Porphyromonas gingivalis is a keystone pathogen of chronic periodontitis. The virulence of P. gingivalis is reported to be strain related and there are currently a number of strain typing schemes based on variation in capsular polysaccharide, the major and minor fimbriae and adhesin domains of Lys-gingipain (Kgp), amongst other surface proteins. P. gingivalis can exchange chromosomal DNA between strains by natural competence and conjugation. The aim of this study was to determine the genetic variability of P. gingivalis strains sourced from international locations over a 25-year period and to determine if variability in surface virulence factors has a phylogenetic basis. Whole genome sequencing was performed on 13 strains and comparison made to 10 previously sequenced strains. A single nucleotide polymorphism-based phylogenetic analysis demonstrated a shallow tri-lobed phylogeny. There was a high level of reticulation in the phylogenetic network, demonstrating extensive horizontal gene transfer between the strains. Two highly conserved variants of the catalytic domain of the major virulence factor the Kgp proteinase (Kgp cat I and Kgp cat II) were found. There were three variants of the fourth Kgp C-terminal cleaved adhesin domain. Specific variants of the cell surface proteins FimA, FimCDE, MfaI, RagAB, Tpr, and PrtT were also identified. The occurrence of all these variants in the P. gingivalis strains formed a mosaic that was not related to the SNP-based phylogeny. In conclusion P. gingivalis uses domain rearrangements and genetic exchange to generate diversity in specific surface virulence factors.

  14. In the Casino of Life: Betting on Risks and Ignoring the Consequences of Climate Change and Hazards

    Science.gov (United States)

    Brosnan, D. M.

    2016-12-01

    Even faced with strong scientific evidence decision-makers cite uncertainty and delay actions. Scientists, confident in the quality of their science and acknowledging that uncertainty while present is low by scientific standards, become more frustrated as their information is ignored. Decreasing scientific uncertainty, a hallmark of long term studies e.g. IPCC reports does little to motivate decision-makers. Imperviousness to scientific data is prevalent across all scales. Municipalities prefer to spend millions of dollars on engineered solutions to climate change and hazards, even if science shows that they perform less well than nature-based ones and cost much more. California is known to be at risk from tsunamis generated by earthquakes off Alaska. A study using a 9.1 earthquake, similar to a 1965 event, calculated the immediate economic price tag in infrastructure loss and business interruption at 9.5billion. The exposure of Los Angeles/Long Beach port trade to damage and downtime exceeds 1.2billion; business interruption would triple the figure. Yet despite several excellent scientific studies, the State is ill prepared; investments in infrastructure commerce and conservation risk being literally washed away. Globally there is a 5-10% probability of an extreme geohazard, e.g, a Tambora like eruption, occurring in this century. With a "value of statistical life" of 2.2 million and population at 7 billion the risk for fatalities alone is 1.1-7billion per yr. But there is little interest in investing the $0.5-3.5 billion per year in volcano monitoring necessary to reduce fatalities and lower risks of global conflict, starvation, and societal destruction. More science and less uncertainty is clearly not the driver of action. But is speaking with certainty really the answer? Decision makers and scientists are in the same casino of life but rarely play at the same tables. Decision makers bet differently to scientists. To motivate action we need to be cognizant of

  15. Visible Light-Induced Metal Free Surface Initiated Atom Transfer Radical Polymerization of Methyl Methacrylate on SBA-15

    Directory of Open Access Journals (Sweden)

    Liang Ma

    2017-02-01

    Full Text Available Surface-initiated atom transfer radical polymerization (SI-ATRP is one of the most versatile techniques to modify the surface properties of materials. Recent developed metal-free SI-ATRP makes such techniques more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N-dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. A SBA-15-based polymeric composite with an adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous conditions. This procedure provides a low-cost, readily available, and easy modification method to synthesize polymeric composites without the contamination of metal.

  16. Specific Features of Chip Making and Work-piece Surface Layer Formation in Machining Thermal Coatings

    Directory of Open Access Journals (Sweden)

    V. M. Yaroslavtsev

    2016-01-01

    Full Text Available A wide range of unique engineering structural and performance properties inherent in metallic composites characterizes wear- and erosion-resistant high-temperature coatings made by thermal spraying methods. This allows their use both in manufacturing processes to enhance the wear strength of products, which have to operate under the cyclic loading, high contact pressures, corrosion and high temperatures and in product renewal.Thermal coatings contribute to the qualitative improvement of the technical level of production and product restoration using the ceramic composite materials. However, the possibility to have a significantly increased product performance, reduce their factory labour hours and materials/output ratio in manufacturing and restoration is largely dependent on the degree of the surface layer quality of products at their finishing stage, which is usually provided by different kinds of machining.When machining the plasma-sprayed thermal coatings, a removing process of the cut-off layer material is determined by its distinctive features such as a layered structure, high internal stresses, low ductility material, high tendency to the surface layer strengthening and rehardening, porosity, high abrasive properties, etc. When coatings are machined these coating properties result in specific characteristics of chip formation and conditions for formation of the billet surface layer.The chip formation of plasma-sprayed coatings was studied at micro-velocities using an experimental tool-setting microscope-based setup, created in BMSTU. The setup allowed simultaneous recording both the individual stages (phases of the chip formation process and the operating force factors.It is found that formation of individual chip elements comes with the multiple micro-cracks that cause chipping-off the small particles of material. The emerging main crack in the cut-off layer of material leads to separation of the largest chip element. Then all the stages

  17. Preparation and surface characterization of activated carbons from Euphorbia rigida by chemical activation with ZnCl2, K2CO3, NaOH and H3PO4

    International Nuclear Information System (INIS)

    Kılıç, Murat; Apaydın-Varol, Esin; Pütün, Ayşe Eren

    2012-01-01

    Highlights: ► An arid land plant evaluated as low cost activated carbon precursor. ► Four types of different chemical activation agents are used. ► Higher surface area (2600 m 2 /g) obtained by chemical activation. ► Obtained activated carbon can be effectively used as an adsorbent for the removal of toxic pollutants from aqueous solutions. - Abstract: Preparation of activated carbons from Euphorbia rigida by chemical activation with different impregnation agents and ratios was studied. ZnCl 2 , K 2 CO 3 , NaOH and H 3 PO 4 were used as chemical activation agents and four impregnation ratios (25–50–75–100%) by mass were applied on biomass. Activation is applied to impregnated biomass samples at 700 °C under sweeping gas in a fixed bed reactor. For determination of chemical and physical properties of the obtained activated carbons; elemental analysis was applied to determine the elemental composition (C, H, N, O) and FT-IR spectra was used to analyze the functional groups. BET equation was used to calculate the surface areas of activated carbons. For understanding the changes in the surface structure, activated carbons were conducted to Scanning Electron Microscopy (SEM). Maximum BET surface area (2613 m 2 /g) was reached with 75% K 2 CO 3 impregnated biomass sample. Experimental results showed that impregnation types and ratios have a significant effect on the pore structure of activated carbon and E. rigida seems to be an alternative precursor for commercial activated carbon production.

  18. Electron and electron-phonon effects in quasi-two-dimensional molecular conductor theta-(BETS) sub 4 HgBr sub 4 (C sub 6 H sub 5 Cl): optical investigations at 300-15 K

    CERN Document Server

    Vlasova, R M; Petrov, B V; Semkin, N D; Zhilyaeva, E I; Bogdanova, O A; Lyubovskaya, R N; Graja, A

    2002-01-01

    One studied the polarized spectra of reflection and spectra of optical transmission of theta-(BETS) sub 4 HgBr sub 4 (C sub 6 H sub 5 Cl) quasi-two-dimensional molecular conductor within 700-6500 cm sup - sup 1 range under 300-15 K temperatures and within 9000-40000 cm sup - sup 1 under 300 K for two principal directions within crystal plane parallel to conducting layers of BETS molecules. Under 300 K within IR region the spectra are characterized by the intensive essential peculiarities (1200-1400 cm sup - sup 1) caused by electron-oscillation coupling (EOC). At temperature drop within 180-80 K range one observes in the spectra a Lorentz term with omega sub t = 2900 cm sup - sup 1 and three extra bands within 800-1180 cm sup - sup 1 region caused by EOC. The derived results are indicative of unstable structural distortions along two principal directions in a crystal followed by formation of a charge density comparable wave

  19. Fabrication of carbon nanospheres by the pyrolysis of polyacrylonitrile–poly(methyl methacrylate core–shell composite nanoparticles

    Directory of Open Access Journals (Sweden)

    Dafu Wei

    2017-09-01

    Full Text Available Carbon nanospheres with a high Brunauer–Emmett–Teller (BET specific surface area were fabricated via the pyrolysis of polyacrylonitrile–poly(methyl methacrylate (PAN–PMMA core–shell nanoparticles. Firstly, PAN–PMMA nanoparticles at high concentration and low surfactant content were controllably synthesized by a two-stage azobisisobutyronitrile (AIBN-initiated semicontinuous emulsion polymerization. The carbon nanospheres were obtained after the PAN core domain was converted into carbon and the PMMA shell was sacrificed via the subsequent heat treatment steps. The thickness of the PMMA shell can be easily adjusted by changing the feeding volume ratio (FVR of methyl methacrylate (MMA to acrylonitrile (AN. At an FVR of 1.6, the coarse PAN cores were completely buried in the PMMA shells, and the surface of the obtained PAN–PMMA nanoparticles became smooth. The thick PMMA shell can inhibit the adhesion between carbon nanospheres caused by cyclization reactions during heat treatment. The carbon nanospheres with a diameter of 35–65 nm and a high BET specific surface area of 612.8 m2/g were obtained from the PAN–PMMA nanoparticles synthesized at an FVR of 1.6. The carbon nanospheres exhibited a large adsorption capacity of 190.0 mg/g for methylene blue, thus making them excellent adsorbents for the removal of organic pollutants from water.

  20. Synthesis of nanoparticles of magnetite by sol-gel and precipitation methods: study of chemical composition and structure

    International Nuclear Information System (INIS)

    Picasso, Gino; Vega, Jaime; Uzuriaga, Rosario; Ruiz, Gean Pieer

    2012-01-01

    In this work, nanoparticles based on magnetite have been prepared by sol-gel and precipitation methods. In the first case two variants have been applied: by growing of sol starting from nitrate precursor and ethylene glycol as solvent and to control the reduction process and force hydrolysis and steric control prepared from ferrum sulfate precursor and sodium citrate. In the second case the starting material was sulfate precursor, ammonium hydroxide as precipitaing agent and ethylene glycol as surfactant. The samples have been characterized by X-ray diffraction technique (XRD), adsorption-desorption of N 2 (BET equation model) and Moessbauer spectroscopy. XRD patterns of all samples showed typical peaks of magnetite which were detected in the following positions: 30,06 o , 35,42 o , 62,55 o . Average specific surface quantified by BET method was ranging from 40 to 50 m 2 /g with isotherm type IV corresponding to mesoporous surface. Moessbauer spectra of sample prepared from sol-gel (gel growing) carried out at home temperature detected the presence of 2 sextets consisting in 2 type of sites: first one due to octahedral positions (Fe 2+ , Fe 3+ ) and the second one due to tetrahedral positions (Fe 3+ ). Grain size of magnetite samples, evaluated by Scherrer equation and specific surface area, was ranging from 2 to 20 nm. (author).

  1. Specific capture and detection of Staphylococcus aureus with high-affinity modified aptamers to cell surface components.

    Science.gov (United States)

    Baumstummler, A; Lehmann, D; Janjic, N; Ochsner, U A

    2014-10-01

    Slow off-rate modified aptamer (SOMAmer) reagents were generated to several Staphylococcus aureus cell surface-associated proteins via SELEX with multiple modified DNA libraries using purified recombinant or native proteins. High-affinity binding agents with sub-nanomolar Kd 's were obtained for staphylococcal protein A (SpA), clumping factors (ClfA, ClfB), fibronectin-binding proteins (FnbA, FnbB) and iron-regulated surface determinants (Isd). Further screening revealed several SOMAmers that specifically bound to Staph. aureus cells from all strains that were tested, but not to other staphylococci or other bacteria. SpA and ClfA SOMAmers proved useful for the selective capture and enrichment of Staph. aureus cells, as shown by culture and PCR, leading to improved limits of detection and efficient removal of PCR inhibitors. Detection of Staph. aureus cells was enhanced by several orders of magnitude when the bacterial cell surface was coated with SOMAmers followed by qPCR of the SOMAmers. Furthermore, fluorescence-labelled SpA SOMAmers demonstrated their utility as direct detection agents in flow cytometry. Significance and impact of the study: Monitoring for microbial contamination of food, water, nonsterile products or the environment is typically based on culture, PCR or antibodies. Aptamers that bind with high specificity and affinity to well-conserved cell surface epitopes represent a promising novel type of reagents to detect bacterial cells without the need for culture or cell lysis, including for the capture and enrichment of bacteria present at low cell densities and for the direct detection via qPCR or fluorescent staining. © 2014 Soma Logic, Inc. published by John Wiley & Sons Ltd On behalf of the society for Applied Microbiology.

  2. Characterization of antigen association with accessory cells: specific removal of processed antigens from the cell surface by phospholipases

    International Nuclear Information System (INIS)

    Falo, L.D. Jr.; Haber, S.I.; Herrmann, S.; Benacerraf, B.; Rock, K.L.

    1987-01-01

    To characterize the basis for the cell surface association of processed antigen with the antigen-presenting cell (APC) the authors analyzed its sensitivity to enzymatic digestion. Antigen-exposed APC that are treated with phospholipase and then immediately fixed lose their ability to stimulate antigen-plus-Ia-specific T-T hybridomas. This effect is seen with highly purified phospholipase A 2 and phospholipase C. In addition it is observed with three distinct antigens - ovalbumin, bovine insulin, and poly(LGlu 56 LLys 35 LPhe 9 )[(GluLysPhe)/sub n/]. The effect of phospholipases is highly specific. Identically treated APC are equivalent to control in their ability to stimulate alloreactive hybridomas specific for precisely the same Ia molecule that is corecognized by antigen-plus-Ia-specific hybrids. Furthermore, the antigen-presenting function of enzyme-treated, fixed APC can be reconstituted by the addition of exogenous in vitro processed or processing independent antigens. In parallel studies 125 I-labeled avidin was shown to specifically bind to APC that were previously exposed and allowed to process biotin-insulin. Biotin-insulin-exposed APC that are pretreated with phospholipase bind significantly less 125 I-labeled avidin than do untreated, exposed APC. Identical enzyme treatment does not reduce the binding of avidin to a biotinylated antibody already bound to class II major histocompatibility complex molecules of APC. These studies demonstrate that phospholipase effectively removes processed cell surface antigen

  3. Acridine orange adsorption by zinc oxide/almond shell activated carbon composite: Operational factors, mechanism and performance optimization using central composite design and surface modeling.

    Science.gov (United States)

    Zbair, M; Anfar, Z; Ait Ahsaine, H; El Alem, N; Ezahri, M

    2018-01-15

    Zinc Oxide/Activated Carbon Powder was used for the adsorptive removal of Acridine Orange dye (AO) from aqueous solution. The prepared composite material was characterized using XRD, XPS, SEM, EDS, FTIR, XRF, Raman, BET surface area and TGA/DTA. The adsorption isotherms, kinetics and thermodynamic studies of AO onto the ZnO-AC were thoroughly analyzed. The kinetic modeling data revealed that the adsorption of AO has a good adjustment to the pseudo-second-order model. Langmuir isotherm model is better fitted for adsorption data and the maximum adsorption capacity was found to be 909.1 mg/g at 313 K. The negative values of ΔG showed the spontaneous nature of the AO adsorption onto ZnO-AC. The results indicated the adsorption was pH dependent which is mainly governed by electrostatic attraction, hydrogen bonding and π-π interaction. Reusability test showed a low decrease in the removal performance of ZnO-AC due to the mesopore filling mechanism confirmed by BET analysis after adsorption. Also, thermal regeneration could deposit AO dye on the surface of the composite leading to the efficiency decrease. Finally, the effect of various parameters such as pH, temperature, contact time and initial dye concentration was studied using response surface methodology (RSM). The model predicted a maximum AO removal (99.42 ± 0.57%) under the optimum conditions, which was very close to the experimental value (99.32 ± 0.18%). Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. HadISDH: an updateable land surface specific humidity product for climate monitoring

    Directory of Open Access Journals (Sweden)

    K. M. Willett

    2013-03-01

    Full Text Available HadISDH is a near-global land surface specific humidity monitoring product providing monthly means from 1973 onwards over large-scale grids. Presented herein to 2012, annual updates are anticipated. HadISDH is an update to the land component of HadCRUH, utilising the global high-resolution land surface station product HadISD as a basis. HadISD, in turn, uses an updated version of NOAA's Integrated Surface Database. Intensive automated quality control has been undertaken at the individual observation level, as part of HadISD processing. The data have been subsequently run through the pairwise homogenisation algorithm developed for NCDC's US Historical Climatology Network monthly temperature product. For the first time, uncertainty estimates are provided at the grid-box spatial scale and monthly timescale. HadISDH is in good agreement with existing land surface humidity products in periods of overlap, and with both land air and sea surface temperature estimates. Widespread moistening is shown over the 1973–2012 period. The largest moistening signals are over the tropics with drying over the subtropics, supporting other evidence of an intensified hydrological cycle over recent years. Moistening is detectable with high (95% confidence over large-scale averages for the globe, Northern Hemisphere and tropics, with trends of 0.089 (0.080 to 0.098 g kg−1 per decade, 0.086 (0.075 to 0.097 g kg−1 per decade and 0.133 (0.119 to 0.148 g kg−1 per decade, respectively. These changes are outside the uncertainty range for the large-scale average which is dominated by the spatial coverage component; station and grid-box sampling uncertainty is essentially negligible on large scales. A very small moistening (0.013 (−0.005 to 0.031 g kg−1 per decade is found in the Southern Hemisphere, but it is not significantly different from zero and uncertainty is large. When globally averaged, 1998 is the moistest year since monitoring began in 1973, closely

  5. Ligand-specific regulation of the extracellular surface of a G-protein-coupled receptor

    Energy Technology Data Exchange (ETDEWEB)

    Bokoch, Michael P.; Zou, Yaozhong; Rasmussen, Søren G.F.; Liu, Corey W.; Nygaard, Rie; Rosenbaum, Daniel M.; Fung, Juan José; Choi, Hee-Jung; Thian, Foon Sun; Kobilka, Tong Sun; Puglisi, Joseph D.; Weis, William I.; Pardo, Leonardo; Prosser, R. Scott; Mueller, Luciano; Kobilka, Brian K. (Stanford-MED); (Toronto); (BMS); (UAB, Spain)

    2010-01-14

    G-protein-coupled receptors (GPCRs) are seven-transmembrane proteins that mediate most cellular responses to hormones and neurotransmitters. They are the largest group of therapeutic targets for a broad spectrum of diseases. Recent crystal structures of GPCRs have revealed structural conservation extending from the orthosteric ligand-binding site in the transmembrane core to the cytoplasmic G-protein-coupling domains. In contrast, the extracellular surface (ECS) of GPCRs is remarkably diverse and is therefore an ideal target for the discovery of subtype-selective drugs. However, little is known about the functional role of the ECS in receptor activation, or about conformational coupling of this surface to the native ligand-binding pocket. Here we use NMR spectroscopy to investigate ligand-specific conformational changes around a central structural feature in the ECS of the {beta}{sub 2} adrenergic receptor: a salt bridge linking extracellular loops 2 and 3. Small-molecule drugs that bind within the transmembrane core and exhibit different efficacies towards G-protein activation (agonist, neutral antagonist and inverse agonist) also stabilize distinct conformations of the ECS. We thereby demonstrate conformational coupling between the ECS and the orthosteric binding site, showing that drugs targeting this diverse surface could function as allosteric modulators with high subtype selectivity. Moreover, these studies provide a new insight into the dynamic behaviour of GPCRs not addressable by static, inactive-state crystal structures.

  6. Synthesis and characterization of WO3 nanostructures prepared by an aged-hydrothermal method

    International Nuclear Information System (INIS)

    Huirache-Acuna, R.; Paraguay-Delgado, F.; Albiter, M.A.; Lara-Romero, J.; Martinez-Sanchez, R.

    2009-01-01

    Nanostructures of tungsten trioxide (WO 3 ) have been successfully synthesized by using an aged route at low temperature (60 deg. C) followed by a hydrothermal method at 200 deg. C for 48 h under well controlled conditions. The material was studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Energy Dispersive Spectroscopy (EDS), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). Specific Surface Area (S BET ) were measured by using the BET method. The lengths of the WO 3 nanostructures obtained are between 30 and 200 nm and their diameters are from 20 to 70 nm. The growth direction of the tungsten oxide nanostructures was determined along [010] axis with an inter-planar distance of 0.38 nm.

  7. Effects of textural and surface characteristics of microporous activated carbons on the methane adsorption capacity at high pressures

    International Nuclear Information System (INIS)

    Bastos-Neto, M.; Canabrava, D.V.; Torres, A.E.B.; Rodriguez-Castellon, E.; Jimenez-Lopez, A.; Azevedo, D.C.S.; Cavalcante, C.L.

    2007-01-01

    The objective of this study is to relate textural and surface characteristics of selected microporous activated carbons to their methane storage capacity. In this work, a magnetic suspension balance (Rubotherm, Germany) was used to measure methane adsorption isotherms of several activated carbon samples. Textural characteristics were assessed by nitrogen adsorption on a regular surface area analyzer (Autosorb-MP, by Quantachrome, USA). N 2 adsorption was analysed by conventional models (BET, DR, HK) and by Monte Carlo molecular simulations. Elemental and surface analyses were performed by X-ray photoelectronic spectroscopy (XPS) for the selected samples. A comparative analysis was then carried out with the purpose of defining some correlation among the variables under study. For the system under study, pore size distribution and micropore volume seem to be a determining factor as long as the solid surface is perfectly hydrophobic. It was concluded that the textural parameters per se do not unequivocally determine natural gas storage capacities. Surface chemistry and methane adsorption equilibria must be taken into account in the decision-making process of choosing an adsorbent for gas storage

  8. How stable 'should' epigenetic modifications be? Insights from adaptive plasticity and bet hedging.

    Science.gov (United States)

    Herman, Jacob J; Spencer, Hamish G; Donohue, Kathleen; Sultan, Sonia E

    2014-03-01

    Although there is keen interest in the potential adaptive value of epigenetic variation, it is unclear what conditions favor the stability of these variants either within or across generations. Because epigenetic modifications can be environmentally sensitive, existing theory on adaptive phenotypic plasticity provides relevant insights. Our consideration of this theory suggests that stable maintenance of environmentally induced epigenetic states over an organism's lifetime is most likely to be favored when the organism accurately responds to a single environmental change that subsequently remains constant, or when the environmental change cues an irreversible developmental transition. Stable transmission of adaptive epigenetic states from parents to offspring may be selectively favored when environments vary across generations and the parental environment predicts the offspring environment. The adaptive value of stability beyond a single generation of parent-offspring transmission likely depends on the costs of epigenetic resetting. Epigenetic stability both within and across generations will also depend on the degree and predictability of environmental variation, dispersal patterns, and the (epi)genetic architecture underlying phenotypic responses to environment. We also discuss conditions that favor stability of random epigenetic variants within the context of bet hedging. We conclude by proposing research directions to clarify the adaptive significance of epigenetic stability. © 2013 The Author(s). Evolution © 2013 The Society for the Study of Evolution.

  9. SU-E-T-04: 3D Printed Patient-Specific Surface Mould Applicators for Brachytherapy Treatment of Superficial Lesions

    International Nuclear Information System (INIS)

    Cumming, I; Lasso, A; Rankin, A; Fichtinger, G; Joshi, C P; Falkson, C; Schreiner, L John

    2014-01-01

    Purpose: Evaluate the feasibility of constructing 3D-printed patient-specific surface mould applicators for HDR brachytherapy treatment of superficial lesions. Methods: We propose using computer-aided design software to create 3D printed surface mould applicators for brachytherapy. A mould generation module was developed in the open-source 3D Slicer ( http://www.slicer.org ) medical image analysis platform. The system extracts the skin surface from CT images, and generates smooth catheter paths over the region of interest based on user-defined start and end points at a specified stand-off distance from the skin surface. The catheter paths are radially extended to create catheter channels that are sufficiently wide to ensure smooth insertion of catheters for a safe source travel. An outer mould surface is generated to encompass the channels. The mould is also equipped with fiducial markers to ensure its reproducible placement. A surface mould applicator with eight parallel catheter channels of 4mm diameters was fabricated for the nose region of a head phantom; flexible plastic catheters of 2mm diameter were threaded through these channels maintaining 10mm catheter separations and a 5mm stand-off distance from the skin surface. The apparatus yielded 3mm thickness of mould material between channels and the skin. The mould design was exported as a stereolithography file to a Dimension SST1200es 3D printer and printed using ABS Plus plastic material. Results: The applicator closely matched its design and was found to be sufficiently rigid without deformation during repeated application on the head phantom. Catheters were easily threaded into channels carved along catheter paths. Further tests are required to evaluate feasibility of channel diameters smaller than 4mm. Conclusion: Construction of 3D-printed mould applicators show promise for use in patient specific brachytherapy of superficial lesions. Further evaluation of 3D printing techniques and materials is required

  10. SU-E-T-04: 3D Printed Patient-Specific Surface Mould Applicators for Brachytherapy Treatment of Superficial Lesions

    Energy Technology Data Exchange (ETDEWEB)

    Cumming, I; Lasso, A; Rankin, A; Fichtinger, G [Laboratory for Percutaneous Surgery, School of Computing, Queen' s University, Kingston, Ontario (Canada); Joshi, C P; Falkson, C; Schreiner, L John [CCSEO, Kingston General Hospital and Department of Oncology, Queen' s University, Kingston, Ontario (Canada)

    2014-06-01

    Purpose: Evaluate the feasibility of constructing 3D-printed patient-specific surface mould applicators for HDR brachytherapy treatment of superficial lesions. Methods: We propose using computer-aided design software to create 3D printed surface mould applicators for brachytherapy. A mould generation module was developed in the open-source 3D Slicer ( http://www.slicer.org ) medical image analysis platform. The system extracts the skin surface from CT images, and generates smooth catheter paths over the region of interest based on user-defined start and end points at a specified stand-off distance from the skin surface. The catheter paths are radially extended to create catheter channels that are sufficiently wide to ensure smooth insertion of catheters for a safe source travel. An outer mould surface is generated to encompass the channels. The mould is also equipped with fiducial markers to ensure its reproducible placement. A surface mould applicator with eight parallel catheter channels of 4mm diameters was fabricated for the nose region of a head phantom; flexible plastic catheters of 2mm diameter were threaded through these channels maintaining 10mm catheter separations and a 5mm stand-off distance from the skin surface. The apparatus yielded 3mm thickness of mould material between channels and the skin. The mould design was exported as a stereolithography file to a Dimension SST1200es 3D printer and printed using ABS Plus plastic material. Results: The applicator closely matched its design and was found to be sufficiently rigid without deformation during repeated application on the head phantom. Catheters were easily threaded into channels carved along catheter paths. Further tests are required to evaluate feasibility of channel diameters smaller than 4mm. Conclusion: Construction of 3D-printed mould applicators show promise for use in patient specific brachytherapy of superficial lesions. Further evaluation of 3D printing techniques and materials is required

  11. The preparation, surface structure, zeta potential, surface charge density and photocatalytic activity of TiO{sub 2} nanostructures of different shapes

    Energy Technology Data Exchange (ETDEWEB)

    Grover, Inderpreet Singh; Singh, Satnam; Pal, Bonamali, E-mail: bpal@thapar.edu

    2013-09-01

    Titania based nanocatalysts such as sodium titanates of different morphology having superior surface properties are getting wide importance in photocatalysis research. Despite having sodium (Na) contents and its high temperature synthesis (that generally deteriorate the photoreactivity), these Na-titanates often exhibit better photoactivity than P25-TiO{sub 2} catalyst. Hence, this work demonstrated the influence of crystal structure, BET surface area, surface charge, zeta potential (ζ) and metal loading on the photocatalytic activity of as-prepared sodium titanate nanotube (TNT) and titania nanorod (TNR). Straw like hollow orthorhombic-TNT (Na{sub 2}Ti{sub 2}O{sub 5}·H{sub 2}O) particles (W = 9–12 nm and L = 82–115 nm) and rice like pure anatase-TNR particles (W = 8–13 nm and L = 81–134 nm) are obtained by the hydrothermal treatment of P25-TiO{sub 2} with NaOH, which in fact, altered the net surface charge of TNT and TNR particles. The observed ζ = −2.82 (P25-TiO{sub 2}), −13.5 (TNT) and −22.5 mV (TNR) are significantly altered by the Ag and Cu deposition. It has been found here that TNT displayed best photocatalytic activity for the imidacloprid insecticide (C{sub 9}H{sub 10}ClN{sub 5}O{sub 2}) degradation to CO{sub 2} formation under UV irradiation because of its largest surface area 176 m{sup 2} g{sup −1} among the catalysts studied.

  12. Obg and Membrane Depolarization Are Part of a Microbial Bet-Hedging Strategy that Leads to Antibiotic Tolerance.

    Science.gov (United States)

    Verstraeten, Natalie; Knapen, Wouter Joris; Kint, Cyrielle Ines; Liebens, Veerle; Van den Bergh, Bram; Dewachter, Liselot; Michiels, Joran Elie; Fu, Qiang; David, Charlotte Claudia; Fierro, Ana Carolina; Marchal, Kathleen; Beirlant, Jan; Versées, Wim; Hofkens, Johan; Jansen, Maarten; Fauvart, Maarten; Michiels, Jan

    2015-07-02

    Within bacterial populations, a small fraction of persister cells is transiently capable of surviving exposure to lethal doses of antibiotics. As a bet-hedging strategy, persistence levels are determined both by stochastic induction and by environmental stimuli called responsive diversification. Little is known about the mechanisms that link the low frequency of persisters to environmental signals. Our results support a central role for the conserved GTPase Obg in determining persistence in Escherichia coli in response to nutrient starvation. Obg-mediated persistence requires the stringent response alarmone (p)ppGpp and proceeds through transcriptional control of the hokB-sokB type I toxin-antitoxin module. In individual cells, increased Obg levels induce HokB expression, which in turn results in a collapse of the membrane potential, leading to dormancy. Obg also controls persistence in Pseudomonas aeruginosa and thus constitutes a conserved regulator of antibiotic tolerance. Combined, our findings signify an important step toward unraveling shared genetic mechanisms underlying persistence. Copyright © 2015 Elsevier Inc. All rights reserved.

  13. Effect of interparticle interactions on size determination of zirconia and silica based systems – A comparison of SAXS, DLS, BET, XRD and TEM

    Science.gov (United States)

    Pabisch, Silvia; Feichtenschlager, Bernhard; Kickelbick, Guido; Peterlik, Herwig

    2012-01-01

    The aim of this work is a systematic comparison of size characterisation methods for two completely different model systems of oxide nanoparticles, i.e. amorphous spherical silica and anisotropic facet-shaped crystalline zirconia. Size and/or size distribution were determined in a wide range from 5 to 70 nm using small-angle X-ray scattering (SAXS), dynamic light scattering (DLS), nitrogen sorption (BET), X-ray diffraction (XRD) and transmission electron microscopy (TEM). A nearly perfect coincidence was observed only for SAXS and TEM for both types of particles. For zirconia nanoparticles considerable differences between different measurement methods were observed. PMID:22347721

  14. Titanium dioxide nanoparticles modified by salicylic acid and arginine: Structure, surface properties and photocatalytic decomposition of p-nitrophenol

    Energy Technology Data Exchange (ETDEWEB)

    Li, Lei [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China); Shanxi Province Key Laboratory of Higee-Oriented Chemical Engineering, North University of China, Taiyuan 030051 (China); Feng, Yujie, E-mail: yujief@hit.edu.cn [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China); Liu, Youzhi; Wei, Bing; Guo, Jiaxin; Jiao, Weizhou [Shanxi Province Key Laboratory of Higee-Oriented Chemical Engineering, North University of China, Taiyuan 030051 (China); Zhang, Zhaohan [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China); Zhang, Qiaoling, E-mail: zhangqiaoling@nuc.edu.cn [Shanxi Province Key Laboratory of Higee-Oriented Chemical Engineering, North University of China, Taiyuan 030051 (China)

    2016-02-15

    Graphical abstract: A simple and versatile synthetic method to produce TiO{sub 2} nanoparticles surface-modified with various organic capping agents can be used for novel multifunctional photocatalysts as required for various applications in energy saving and environmental protection. - Highlights: • SA and Arg was modified through the method of dipping treatment-based on chemical adsorption in saturated solution. • Surface modified TiO{sub 2} applied in photodecomposition of nitroaromatic. • The photoreduction of nitroaromatic and photocatalytic activity under visible light irradiation were enhanced by TiO{sub 2}–SA–Arg. • TiO{sub 2}–SA–Arg showed better lipophilic, dispersion and adsorption properties. - Abstract: In this study, titanium dioxide (TiO{sub 2}) nanoparticles were surface-modified with salicylic acid (SA) and arginine (Arg) using an environmentally friendly and convenient method, and the bonding structure, surface properties and degradation efficiency of p-nitrophenol (PNP) were investigated. X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET), X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared spectroscopy (FT-IR), water contact angle (WCA) measurements, ζ-potentiometric analysis, UV/visible diffuse reflectance spectroscopy (UV–vis DRS), and thermogravimetric analysis (TGA) were performed to evaluate the modification effect. The degradation rates were determined by high-performance liquid chromatography (HPLC). The results show that bidentate or bridging bonds are most likely formed between SA/Arg and TiO{sub 2} surface. Surface modification with SA, Arg, or both can improve the lipophilic properties and decrease the zeta potential, and also result in a red shift of the absorption wavelength. TiO{sub 2} nanoparticles modified by Arg or both SA and Arg show a large specific surface area and pore volume. Further, degradation

  15. Fabrication of Water Jet Resistant and Thermally Stable Superhydrophobic Surfaces by Spray Coating of Candle Soot Dispersion.

    Science.gov (United States)

    Qahtan, Talal F; Gondal, Mohammed A; Alade, Ibrahim O; Dastageer, Mohammed A

    2017-08-08

    A facile synthesis method for highly stable carbon nanoparticle (CNP) dispersion in acetone by incomplete combustion of paraffin candle flame is presented. The synthesized CNP dispersion is the mixture of graphitic and amorphous carbon nanoparticles of the size range of 20-50 nm and manifested the mesoporosity with an average pore size of 7 nm and a BET surface area of 366 m 2 g -1 . As an application of this material, the carbon nanoparticle dispersion was spray coated (spray-based coating) on a glass surface to fabricate superhydrophobic (water contact angle > 150° and sliding angle fabricated from direct candle flame soot deposition (candle-based coating). This study proved that water jet resistant and thermally stable superhydrophobic surfaces can be easily fabricated by simple spray coating of CNP dispersion gathered from incomplete combustion of paraffin candle flame and this technique can be used for different applications with the potential for the large scale fabrication.

  16. Adsorption of Carbon Dioxide onto Tetraethylenepentamine Impregnated PMMA Sorbents with Different Pore Structure

    Energy Technology Data Exchange (ETDEWEB)

    Jo, Dong Hyun; Park, Cheonggi; Jung, Hyunchul; Kim, Sung Hyun [Korea University, Seoul (Korea, Republic of)

    2015-02-15

    Poly(methyl methacrylate) (PMMA) supports and amine additives were investigated to adsorb CO{sub 2}. PMMA supports were fabricated by using different ratio of pore forming agents (porogen) to control the BET specific surface area, pore volume and distribution. Toluene and xylene are used for porogens. Supported amine sorbents were prepared by wet impregnation of tetraethylenepentamine (TEPA) on PMMA supports. So we could identify the effect of the pore structure of supports and the quantity of impregnated TEPA on the adsorption capacity. The increased amount of toluene as pore foaming agent resulted in the decreased average pore diameter and the increased BET surface area. Polymer supports with huge different pore distribution could be fabricated by controlling the ratio of porogen. After impregnation, the support with micropore structure is supposed the pore blocking and filling effect so that it has low CO{sub 2} capacity and kinetics due to the difficulty of diffusing. Macropore structure indicates fast adsorption capacity and low influence of amine loading. In case of support with mesopore, it has high performance of adsorption capacity and kinetics. So high surface area and meso-/macro- pore structure is suitable for CO{sub 2} capture.

  17. Functionalization of the hydroxyapatite nanoparticles surface: source of new applications

    International Nuclear Information System (INIS)

    Rojas Sanchez, Leonardo

    2012-01-01

    The surface of the nano-calcium hydroxyapatite, Ca 10 (PO 4 ) 6 (OH) 2 is reacted with stearic acid, succinic anhydride, succinimide and 2 a minoetil dihydrogenphosphate. Introduction of different functional groups is given onto the surface. An ionic interaction is identified by infrared spectroscopy and Raman between the carboxylate groups of the resulting organic molecules and calcium of the hydroxyapatite. The formation of a P-O-P pyrophosphate type bond has been for 2-aminoethyl dihydrogen phosphate with hydroxyapatite groups. Hydroxyapatite phase was remained in all cases after the reaction as demonstrated by diffraction of x-ray in powder. The amount of spiked molecules is quantified by analysis of thermal degradation which together with the determination of the surface area by BET isotherms of nitrogen adsorption. A degree of surface coverage is estimated by the organic molecules. A maximum percentage of 71% is obtained for the functionalization with succinic anhydride, followed by 57% for the reaction with stearic acid. Dilute suspensions of different materials were prepared for which in phosphate buffer solution have presented two populations around 2 and 5 μm in diameter for the modified particles. The ζ-Potential of various materials was determined occurring a variation in the potential of the unmodified hydroxyapatite. The particles with physicochemical properties different of the starting hydroxyapatite were obtained, this has expanded the range of application of the material. (author) [es

  18. Synthesis and capacitance properties of N-doped porous carbon/NiO nanosheet composites using coal-based polyaniline as carbon and nitrogen source

    Science.gov (United States)

    Wang, Xiaoqin; Li, Qiaoqin; Zhang, Yong; Yang, Yufei; Cao, Zhi; Xiong, Shanxin

    2018-06-01

    A novel synthesis approach of N-doped porous carbon (NPC)/NiO composites possessing some honeycomb-shaped nanoporous carbon and plentiful NiO nanosheets is exploited. First NPC/Ni composites are achieved with NPC yield of 52.9% through a catalytic pyrolysis method, using coal-based polyaniline particles prepared by an in-situ polymerization method as a carbon and nitrogen source, and nickel particles as a catalyst, respectively. Next NPC/NiO composites are achieved unexpectedly with plentiful NiO nanosheets and N content of 1.00 wt% after a liquid oxidation process. In NPC/NiO composites, porous carbon mainly presents in the amorphous state, while the incorporated nitrogen mainly presents in the form of pyrrolic N (92.9 at.%) and oxidized N (7.1 at.%). Plentiful NiO nanosheets are embedded in the pores or on the NPC surface. 33.3 at.% Ni2O3 components exist in the surface of NiO nanosheets. NPC/NiO composites possess not only rich micropores, but also significant mesopores and nanoscale macropores. The BET specific surface area, BET average pore width and BJH adsorption average pore diameter are 627.5 m2/g, 2.0 nm and 5.1 nm, respectively. NPC/NiO composites demonstrate a high specific capacitance of 404.1 F/g at 1 A/g, and a good cycling stability maintaining high specific capacitance of 212.4 F/g (84.3% of the initial capacitance) at 5 A/g after 5000 cycles of charge and discharge, attributed to some honeycomb-shaped nanopores of carbon and large specific surface area of NiO nanosheets, and the synergistic effects between electric double-layer capacitance of NPC and pseudocapacitance of NiO. This study may provide a novel approach for the value-added applications of low-rank coal.

  19. Modificación de Betún-Venezuela por reacción de Friedel y Crafts

    Directory of Open Access Journals (Sweden)

    Blanco, Manuel

    1987-03-01

    Full Text Available In this work, a Venezuelan-bitumen of newtonian nature was modified by Friedel and Crafts reaction, changing it in new materials that present pseudoplastic characteristics, with very different properties from the original product. These new materials are harder and have less thermical susceptibility and allow us to use them in many applications such as paving and roofing. The modifications have been made with rubbers, PVC, phtalic anhydride, maleic anhydride, 1, 2-propyleneglycol, hexamethylenediisocyanate and toluylene-2,4-diisocyanate.

    En el presente trabajo se modificó un betún-Venezuela, de naturaleza newtoniana, mediante reacción de Friedel y Crafts, transformándolo en unos nuevos materiales, ya de carácter pseudoplástico, con unas propiedades notablemente distintas a las del producto de partida. Los nuevos materiales son más duros y de menor susceptibilidad térmica, lo que los hace útiles para pavimentación e impermeabilización. Las modificaciones se han realizado con cauchos, policloruro de vinilo, anhídrido ftálico, anhídrido maléico, 1,2-propanodiol, hexametilendiisocianato y toluen-2,4-diisocianato.

  20. Routine systemic antibiotic prophylaxis for burn injuries in developing countries: A best evidence topic (BET)

    Science.gov (United States)

    Stewart, Barclay T; Gyedu, Adam; Agbenorku, Pius; Amankwa, Richcane; Kushner, Adam L; Gibran, Nicole

    2015-01-01

    Background Burns are common in low- and middle-income countries (LMICs) and complicated by unhygienic conditions, malnutrition, use of high-risk homemade dressings and delayed presentation. Resultantly, use of routine systemic antibiotic prophylaxis (SAP) to prevent wound infection is common practice despite this intervention being abandoned in high-income countries due to increased antimicrobial resistance and non-bacterial suprainfection, Methods A best evidence topic (BET) was constructed using a structured protocol. The question addressed was: In LMICs, does routine use of SAP reduce burn wound infection, morbidity or mortality? Results From 704 retrieved records, 48 reports met criteria to be examined. Of those, 3 studies represented the best available evidence. Together, two randomized clinical trials (RCTs) and a retrospective cohort study reported no difference in the proportion of wound infection, any infection or length of hospital stay between SAP groups and controls. One RCT described a greater proportion of wounds infected with P. aeruginosa among SAP arms compared to controls. The studies had few participants and significant methodological weaknesses. Conclusion On the basis of limited, currently available evidence, the use of SAP cannot be recommended for patients in LMICs that present soon after burn injury. PMID:26260622

  1. Glass dissolution rate measurement and calculation revisited

    Energy Technology Data Exchange (ETDEWEB)

    Fournier, Maxime, E-mail: maxime.fournier@cea.fr [CEA, DEN, DTCD, SECM, F-30207, Bagnols sur Cèze (France); Ull, Aurélien; Nicoleau, Elodie [CEA, DEN, DTCD, SECM, F-30207, Bagnols sur Cèze (France); Inagaki, Yaohiro [Department of Applied Quantum Physics & Nuclear Engineering, Kyushu University, Fukuoka, 819-0395 (Japan); Odorico, Michaël [ICSM-UMR5257 CEA/CNRS/UM2/ENSCM, Site de Marcoule, BP17171, F-30207, Bagnols sur Cèze (France); Frugier, Pierre; Gin, Stéphane [CEA, DEN, DTCD, SECM, F-30207, Bagnols sur Cèze (France)

    2016-08-01

    Aqueous dissolution rate measurements of nuclear glasses are a key step in the long-term behavior study of such waste forms. These rates are routinely normalized to the glass surface area in contact with solution, and experiments are very often carried out using crushed materials. Various methods have been implemented to determine the surface area of such glass powders, leading to differing values, with the notion of the reactive surface area of crushed glass remaining vague. In this study, around forty initial dissolution rate measurements were conducted following static and flow rate (SPFT, MCFT) measurement protocols at 90 °C, pH 10. The international reference glass (ISG), in the forms of powders with different particle sizes and polished monoliths, and soda-lime glass beads were examined. Although crushed glass grains clearly cannot be assimilated with spheres, it is when using the samples geometric surface (S{sub geo}) that the rates measured on powders are closest to those found for monoliths. Overestimation of the reactive surface when using the BET model (S{sub BET}) may be due to small physical features at the atomic scale—contributing to BET surface area but not to AFM surface area. Such features are very small compared with the thickness of water ingress in glass (a few hundred nanometers) and should not be considered in rate calculations. With a S{sub BET}/S{sub geo} ratio of 2.5 ± 0.2 for ISG powders, it is shown here that rates measured on powders and normalized to S{sub geo} should be divided by 1.3 and rates normalized to S{sub BET} should be multiplied by 1.9 in order to be compared with rates measured on a monolith. The use of glass beads indicates that the geometric surface gives a good estimation of glass reactive surface if sample geometry can be precisely described. Although data clearly shows the repeatability of measurements, results must be given with a high uncertainty of approximately ±25%. - Highlights: • Initial dissolution

  2. Nitrides and carbides of molybdenum and tungsten with high specific-surface area: their synthesis, structure, and catalytic properties

    International Nuclear Information System (INIS)

    Volpe, L.

    1985-01-01

    Temperature-programmed reactions between trioxides of molybdenum or tungsten and ammonia provide a new method to synthesize dimolybdenum and ditungsten nitrides with specific surface areas to two-hundred-and-twenty and ninety-one square meters per gram, respectively. These are the highest values on record for any unsupported metallic powders. They correspond to three-four nonometer particles. The reaction of molybdenum trioxide with ammonia is topotactic in the sense that one-zero-zero planes of dimolybdenum nitride are parallel to zero-one-zero planes of molybdenum trioxide. As the trioxide transforms, it passes through an oxynitride intermediate with changing bulk structure and increasing surface area and extent of reduction. The nitride product consists of platelets, pseudomorphous with the original trioxide, which can be regarded as highly porous defect single crystals. By treating small particles of dimolybdenum or ditungsten nitride with methane-dihydrogen mixtures it is possible to replace interstitial nitrogen atoms by carbon atoms, without sintering, and thus to prepare carbides of molybdenum and tungsten with very high specific surface areas. Molybdenum nitride powders catalyze ammonia synthesis. A pronounced increase in the catalytic activity with increasing particle size confirms the structure-sensitive character of this reaction

  3. The sorption behavior of Cs and Cd onto oxide and clay surfaces

    International Nuclear Information System (INIS)

    Westrich, H.R.; Cygan, R.T.; Brady, P.V.; Nagy, K.L.; Anderson, H.L.; Kirkpatrick, R.J.

    1995-01-01

    The sorption of Cs and Cd on model soil minerals was examined by complementary analytical and experimental procedures. X-ray photoelectron spectroscopy (XPS) and nuclear magnetic resonance (NMR) spectroscopy were used to characterize the chemical and physical nature of Cs-reacted soil minerals. Cd and Cs adsorption isotherms for kaolinite were also measured at variable pH and temperature to establish likely reaction stoichiometries, while atomic force microscopy (AFM) was used to characterize the microtopography of the clay surface. XPS analyses of Cs-exchanged samples show that Cs is sorbed at mineral surfaces and at the interlayer site of smectite clays, although the spectral resolution of XPS analyses is insufficient to differentiate between basal, edge or interlayer sites. 133 Cs MAS-NMR results also show that Cs is adsorbed primarily in an interlayer site of montmorillonite and on edge and basal sites for kaolinite. Cd adsorption isotherms on kaolinite were found to be additive using Al 2 0 3 + Si0 2 Cd binding constants. AFM quantification of kaolinite crystallites suggest that edges comprise up to 50% of the BET surface area, and are consistent with NMR and surface charge results that Cs an Cd adsorption occur primarily at edge sites

  4. Atom-specific look at the surface chemical bond using x-ray emission spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, A.; Wassdahl, N.; Weinelt, M. [Uppsala Univ. (Sweden)] [and others

    1997-04-01

    CO and N{sub 2} adsorbed on the late transition metals have become prototype systems regarding the general understanding of molecular adsorption. It is in general assumed that the bonding of molecules to transition metals can be explained in terms of the interaction of the frontier HOMO and LUMO molecular orbitals with the d-orbitals. In such a picture the other molecular orbitals should remain essentially the same as in the free molecule. For the adsorption of the isoelectronic molecules CO and N{sub 2} this has led to the so called Blyholder model i.e., a synergetic {sigma} (HOMO) donor and {pi} (LUMO) backdonation bond. The authors results at the ALS show that such a picture is oversimplified. The direct observation and identification of the states related to the surface chemical bond is an experimental challenge. For noble and transition metal surfaces, the adsorption induced states overlap with the metal d valence band. Their signature is therefore often obscured by bulk substrate states. This complication has made it difficult for techniques such as photoemission and inverse photoemission to provide reliable information on the energy of chemisorption induced states and has left questions unanswered regarding the validity of the frontier orbitals concept. Here the authors show how x-ray emission spectroscopy (XES), in spite of its inherent bulk sensitivity, can be used to investigate adsorbed molecules. Due to the localization of the core-excited intermediate state, XE spectroscopy allows an atomic specific separation of the valence electronic states. Thus the molecular contributions to the surface measurements make it possible to determine the symmetry of the molecular states, i.e., the separation of {pi} and {sigma} type states. In all the authors can obtain an atomic view of the electronic states involved in the formation of the chemical bond to the surface.

  5. Microstructure and thermal conductivity of surfactant-free NiO nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Sahoo, Pranati [Laboratory for Emerging Energy and Electronic Materials, Materials Science and Engineering Department, University of Michigan, Ann Arbor, MI 48109 (United States); Department of Chemistry, University of New Orleans, New Orleans, LA 70148 (United States); Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Misra, Dinesh K. [The Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Salvador, Jim [Chemical Sciences and Materials Systems Laboratory, General Motors R and D Center, Warren, MI 48090 (United States); Makongo, Julien P.A. [Laboratory for Emerging Energy and Electronic Materials, Materials Science and Engineering Department, University of Michigan, Ann Arbor, MI 48109 (United States); Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Chaubey, Girija S. [Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Takas, Nathan J. [Laboratory for Emerging Energy and Electronic Materials, Materials Science and Engineering Department, University of Michigan, Ann Arbor, MI 48109 (United States); Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Wiley, John B. [Department of Chemistry, University of New Orleans, New Orleans, LA 70148 (United States); Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Poudeu, Pierre F.P., E-mail: ppoudeup@umich.edu [Laboratory for Emerging Energy and Electronic Materials, Materials Science and Engineering Department, University of Michigan, Ann Arbor, MI 48109 (United States); Department of Chemistry, University of New Orleans, New Orleans, LA 70148 (United States); Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States)

    2012-06-15

    High purity, nanometer sized surfactant-free nickel oxide (NiO) particles were produced in gram scale using a solution combustion method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), gas pycnometry and gas adsorption analysis (BET). The average particle size of the as-synthesized NiO increases significantly with the preheating temperature of the furnace, while the specific surface area decreases. A BET specific surface area of {approx}100 m{sup 2}/g was obtained for NiO nanoparticles with size as small as 3 nm synthesized at 300 Degree-Sign C. The thermal conductivity ({kappa}) of pressed pellets of the synthesized NiO nanoparticles obtained using spark plasma sintering (SPS) and uniaxial hot pressing is drastically decreased ({approx}60%) compared to that of NiO single crystal. This strong reduction in {kappa} with particle size suggests the suitability of the synthesized surfactant-free NiO nanoparticles for use as nanoinclusions when designing high performance materials for waste heat recovery. - Graphical abstract: Highly efficient phonon scattering by surfactant-free NiO nanostructures obtained by solution combustion of a mixture of nickel (II) nitrate hexahydrate (oxidizer) and urea (fuel) at various temperatures. Highlights: Black-Right-Pointing-Pointer Fast synthesis of surfactant-free NiO nanoparticles with controllable size. Black-Right-Pointing-Pointer High specific surface area for NiO nanoparticles with size range from 3 to 7 nm. Black-Right-Pointing-Pointer Strong reduction of the thermal conductivity with decreasing particle size. Black-Right-Pointing-Pointer NiO as nanoinclusions in high performance materials for energy conversion.

  6. Microstructure and thermal conductivity of surfactant-free NiO nanostructures

    International Nuclear Information System (INIS)

    Sahoo, Pranati; Misra, Dinesh K.; Salvador, Jim; Makongo, Julien P.A.; Chaubey, Girija S.; Takas, Nathan J.; Wiley, John B.; Poudeu, Pierre F.P.

    2012-01-01

    High purity, nanometer sized surfactant-free nickel oxide (NiO) particles were produced in gram scale using a solution combustion method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), gas pycnometry and gas adsorption analysis (BET). The average particle size of the as-synthesized NiO increases significantly with the preheating temperature of the furnace, while the specific surface area decreases. A BET specific surface area of ∼100 m 2 /g was obtained for NiO nanoparticles with size as small as 3 nm synthesized at 300 °C. The thermal conductivity (κ) of pressed pellets of the synthesized NiO nanoparticles obtained using spark plasma sintering (SPS) and uniaxial hot pressing is drastically decreased (∼60%) compared to that of NiO single crystal. This strong reduction in κ with particle size suggests the suitability of the synthesized surfactant-free NiO nanoparticles for use as nanoinclusions when designing high performance materials for waste heat recovery. - Graphical abstract: Highly efficient phonon scattering by surfactant-free NiO nanostructures obtained by solution combustion of a mixture of nickel (II) nitrate hexahydrate (oxidizer) and urea (fuel) at various temperatures. Highlights: ► Fast synthesis of surfactant-free NiO nanoparticles with controllable size. ► High specific surface area for NiO nanoparticles with size range from 3 to 7 nm. ► Strong reduction of the thermal conductivity with decreasing particle size. ► NiO as nanoinclusions in high performance materials for energy conversion.

  7. Synthesis of SAPO-56 with controlled crystal size

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Ting; Feng, Xuhui [Colorado School of Mines, Chemical and Biological Engineering Department (United States); Carreon, Maria L. [University of Tulsa, Rusell School of Chemical Engineering (United States); Carreon, Moises A., E-mail: mcarreon@mines.edu [Colorado School of Mines, Chemical and Biological Engineering Department (United States)

    2017-03-15

    Herein, we present the hydrothermal synthesis of SAPO-56 crystals with relatively controlled crystal/particle size. The effects of water content, aluminum source, gel composition, stirring, crystallization temperature and time, as well as the incorporation of crystal growth inhibitors during synthesis were systematically investigated. The synthesized SAPO-56 crystals displayed BET surface areas as high as ∼630 m{sup 2} g{sup −1} with relative narrow size distribution in the ∼5–60 μm range. Nitrogen BET surface areas in the 451 to 631 m{sup 2} g{sup −1} range were observed. Decreasing the crystallization temperature from 220 to 210 °C helped to decrease the average SAPO-56 crystal size. Diluted gel compositions promoted the formation of smaller crystals. Crystal growth inhibitors were found to be helpful in reducing crystal size and narrow the size distribution. Specifically, ∼5 μm SAPO-56 crystals displaying narrow size distribution were synthesized employing aluminum-tri-sec-butoxide as Al source, high water content, and high stirring rates.

  8. Synthesis of SAPO-56 with controlled crystal size

    International Nuclear Information System (INIS)

    Wu, Ting; Feng, Xuhui; Carreon, Maria L.; Carreon, Moises A.

    2017-01-01

    Herein, we present the hydrothermal synthesis of SAPO-56 crystals with relatively controlled crystal/particle size. The effects of water content, aluminum source, gel composition, stirring, crystallization temperature and time, as well as the incorporation of crystal growth inhibitors during synthesis were systematically investigated. The synthesized SAPO-56 crystals displayed BET surface areas as high as ∼630 m"2 g"−"1 with relative narrow size distribution in the ∼5–60 μm range. Nitrogen BET surface areas in the 451 to 631 m"2 g"−"1 range were observed. Decreasing the crystallization temperature from 220 to 210 °C helped to decrease the average SAPO-56 crystal size. Diluted gel compositions promoted the formation of smaller crystals. Crystal growth inhibitors were found to be helpful in reducing crystal size and narrow the size distribution. Specifically, ∼5 μm SAPO-56 crystals displaying narrow size distribution were synthesized employing aluminum-tri-sec-butoxide as Al source, high water content, and high stirring rates.

  9. The hydrochemical identification of groundwater flowing to the Bet She’an-Harod multiaquifer system (Lower Jordan Valley) by rare earth elements, yttrium, stable isotopes (H, O) and Tritium

    International Nuclear Information System (INIS)

    Siebert, Christian; Rosenthal, Eliahu; Möller, Peter; Rödiger, Tino; Meiler, Miki

    2012-01-01

    The Bet She’an and Harod Valleys in Israel are regional recipients and mixing zones for groundwater draining from a multiple aquifer system, which includes carbonate and basalt aquifers and deep-seated pressurized brines. The aquifers drain through two types of outlets, distinct and mixed. The latter type is mainly conditioned by the occurrence of fault-blocks related to the Jordan Rift system, which act as connecting media between the aquifers and facilitate interaquifer flow. Conjoint application of rare earth element distribution and water isotopes enables detection of the local areas replenishment by rainfall infiltration and, in connection with the position of wells or springs, the identification of groundwater flow paths. Once stationary equilibria are established changes of REY composition between REY in groundwater and their surface adsorption, are negligible. In areas with little soil coverage and vegetation even recharge over young Tertiary and diagenetic Cretaceous limestones is distinguishable by their REY distribution patterns. Groundwater recharged over Tertiary limestones show higher REY abundance and more significant Ce anomalies than those derived from the Cretaceous limestones. Weathering of alkali olivine basalts leads to REY patterns in groundwater depleted in the middle REE. The improved knowledge of the hydrological systems is thought to be useful for regional hydrogeological modeling and for designing rational water management schemes.

  10. A microbial-mineralization approach for syntheses of iron oxides with a high specific surface area.

    Science.gov (United States)

    Yagita, Naoki; Oaki, Yuya; Imai, Hiroaki

    2013-04-02

    Of minerals and microbes: A microbial-mineralization-inspired approach was used to facilitate the syntheses of iron oxides with a high specific surface area, such as 253 m(2)g(-1) for maghemite (γ-Fe(2)O(3)) and 148 m(2)g(-1) for hematite (α-Fe(2)O(3)). These iron oxides can be applied to electrode material of lithium-ion batteries, adsorbents, and catalysts. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Growth of porous anodized alumina on the sputtered aluminum films with 2D-3D morphology for high specific surface area

    Science.gov (United States)

    Liao, M. W.; Chung, C. K.

    2014-08-01

    The porous anodic aluminum oxide (AAO) with high-aspect-ratio pore channels is widely used as a template for fabricating nanowires or other one-dimensional (1D) nanostructures. The high specific surface area of AAO can also be applied to the super capacitor and the supporting substrate for catalysis. The rough surface could be helpful to enhance specific surface area but it generally results in electrical field concentration even to ruin AAO. In this article, the aluminum (Al) films with the varied 2D-3D morphology on Si substrates were prepared using magnetron sputtering at a power of 50 W-185 W for 1 h at a working pressure of 2.5 × 10-1 Pa. Then, AAO was fabricated from the different Al films by means of one-step hybrid pulse anodizing (HPA) between the positive 40 V and the negative -2 V (1 s:1 s) for 3 min in 0.3 M oxalic acid at a room temperature. The microstructure and morphology of Al films were characterized by X-ray diffraction, scanning electron microscope and atomic force microscope, respectively. Some hillocks formed at the high target power could be attributed to the grain texture growth in the normal orientation of Al(1 1 1). The 3D porous AAO structure which is different from the conventional 2D planar one has been successfully demonstrated using HPA on the film with greatly rough hillock-surface formed at the highest power of 185 W. It offers a potential application of the new 3D AAO to high specific surface area devices.

  12. Site-specific Pt deposition and etching on electrically and thermally isolated SiO2 micro-disk surfaces

    International Nuclear Information System (INIS)

    Saraf, Laxmikant V

    2010-01-01

    Electrically and thermally isolated surfaces are crucial for improving the detection sensitivity of microelectronic sensors. The site-specific in situ growth of Pt nano-rods on thermally and electrically isolated SiO 2 micro-disks using wet chemical etching and a focused ion/electron dual beam (FIB-SEM) is demonstrated. Fabrication of an array of micro-cavities on top of a micro-disk is also demonstrated. The FIB source is utilized to fabricate through-holes in the micro-disks. Due to the amorphous nature of SiO 2 micro-disks, the Ga implantation possibly modifies through-hole sidewall surface chemistry rather than affecting its transport properties. Some sensor design concepts based on micro-fabrication of SiO 2 micro-disks utilizing thermally and electrically isolated surfaces are discussed from the viewpoint of applications in photonics and bio-sensing.

  13. Study on Purification Diatomite with nitric acid by Thermal Closed System

    Directory of Open Access Journals (Sweden)

    Kuang Meng

    2016-01-01

    Full Text Available In this research, a purification approach using nitric acid leaching at thermal closed system was developed to improve the porous structure of raw diatomite by removal of impurities from its surface and clogged pores. The feasibility and efficiency of this approach were determined by XRF for chemical constitution of diatomite, SEM for morphology and BET for specific surface area of purified diatomite. The investigations indicated that the content of SiO2 was in order of 85.14% for raw diatomite and 98% for purified diatomite, the content of Fe2O3 decreases after purified; the integrity of the porous structure was confirmed by SEM, and increase in specific surface area from 18m2·g-1 to 36m2·g-1.

  14. Preparation and Characterization of Carbon Nanotubes-Based Composite Electrodes for Electric Double Layer Capacitors

    International Nuclear Information System (INIS)

    Seo, Min Kang; Park, Soo Jin

    2012-01-01

    In this work, we prepared activated multi-walled carbon nanotubes/polyacrylonitrile (A-MWCNTs/C) composites by film casting and activation method. Electrochemical properties of the composites were investigated in terms of serving as MWCNTs-based electrode materials for electric double layer capacitors (EDLCs). As a result, the A-MWCNTs/C composites had much higher BET specific surface area, and pore volume, and lower volume ratio of micropores than those of pristine MWCNTs/PAN ones. Furthermore, some functional groups were added on the surface of the A-MWCNTs/C composites. The specific capacitance of the A-MWCNTs/C composites was more than 4.5 times that of the pristine ones at 0.1 V discharging voltage owing to the changes of the structure and surface characteristics of the MWCNTs by activation process

  15. Enhancing the specificity of polymerase chain reaction by graphene oxide through surface modification: zwitterionic polymer is superior to other polymers with different charges

    Science.gov (United States)

    Zhong, Yong; Huang, Lihong; Zhang, Zhisen; Xiong, Yunjing; Sun, Liping; Weng, Jian

    2016-01-01

    Graphene oxides (GOs) with different surface characteristics, such as size, reduction degree and charge, are prepared, and their effects on the specificity of polymerase chain reaction (PCR) are investigated. In this study, we demonstrate that GO with a large size and high reduction degree is superior to small and nonreduced GO in enhancing the specificity of PCR. Negatively charged polyacrylic acid (PAA), positively charged polyacrylamide (PAM), neutral polyethylene glycol (PEG) and zwitterionic polymer poly(sulfobetaine) (pSB) are used to modify GO. The PCR specificity-enhancing ability increases in the following order: GO-PAA Pfu DNA polymerase. Our data demonstrate that the size, reduction degree and surface charge of GO affect the specificity of PCR. Based on our results, zwitterionic polymer-modified GO may be used as an efficient additive for enhancing the specificity of PCR. PMID:27956830

  16. Micelle-template synthesis of hollow silica spheres for improving water vapor permeability of waterborne polyurethane membrane

    OpenAIRE

    Bao, Yan; Wang, Tong; Kang, Qiaoling; Shi, Chunhua; Ma, Jianzhong

    2017-01-01

    Hollow silica spheres (HSS) with special interior spaces, high specific surface area and excellent adsorption and permeability performance were synthesized via micelle-template method using cetyl trimethyl ammonium bromide (CTAB) micelles as soft template and tetraethoxysilane (TEOS) as silica precursor. SEM, TEM, FT-IR, XRD, DLS and BET-BJH were carried out to characterize the morphology and structure of as-obtained samples. The results demonstrated that the samples were amorphous with a hol...

  17. Specification for a surface-search radar-detection-range model

    Science.gov (United States)

    Hattan, Claude P.

    1990-09-01

    A model that predicts surface-search radar detection range versus a variety of combatants has been developed at the Naval Ocean Systems Center. This model uses a simplified ship radar cross section (RCS) model and the U.S. Navy Oceanographic and Atmospheric Mission Library Standard Electromagnetic Propagation Model. It provides the user with a method of assessing the effects of the environment of the performance of a surface-search radar system. The software implementation of the model is written in ANSI FORTRAN 77, with MIL-STD-1753 extensions. The program provides the user with a table of expected detection ranges when the model is supplied with the proper environmental radar system inputs. The target model includes the variation in RCS as a function of aspect angle and the distribution of reflected radar energy as a function of height above the waterline. The modeled propagation effects include refraction caused by a multisegmented refractivity profile, sea-surface roughness caused by local winds, evaporation ducting, and surface-based ducts caused by atmospheric layering.

  18. High prevalence of sensitization to gibberellin-regulated protein (peamaclein) in fruit allergies with negative immunoglobulin E reactivity to Bet v 1 homologs and profilin: Clinical pattern, causative fruits and cofactor effect of gibberellin-regulated protein allergy.

    Science.gov (United States)

    Inomata, Naoko; Miyakawa, Mami; Aihara, Michiko

    2017-07-01

    Gibberellin-regulated protein (GRP) is a new allergen in peach allergy, with an amino acid sequence very well conserved through several botanical species. We investigated the allergenicity of GRP in fruit allergies other than peaches and identified the clinical characteristics of fruit allergy patients with GRP sensitization. One hundred consecutive Japanese patients with fruit allergies were enrolled in the present study. To identify the features of GRP sensitization, we selected patients with negative ImmunoCAP results for Bet v 1 homologs and profilin, which are marker allergens for pollen-food allergy syndrome (PFAS), or lipid transfer protein. These patients underwent specific immunoglobulin E measurements by enzyme-linked immunosorbent assay (ELISA) and skin prick tests (SPT) using purified nPru p 7. Twenty of 100 consecutive patients with fruit allergies had negative ImmunoCAP results for Bet v 1 homologs and profilin. Thirteen (65.0%) of the 20 patients had positive ELISA and/or SPT results using nPru p 7, whereas one of the 20 patients had positive ImmunoCAP results for Pru p 3. In 13 nPru p 7-sensitized patients, the causative foods were peaches (92.3%), apricots (61.5%), oranges (46.2%) and apples (30.8%). Ten patients (76.9%) had multiple causative fruits. Frequent symptoms included facial edema (92.3%) and laryngeal tightness (66.7%). In eight patients (61.5%), exercise or aspirin intake enhanced the allergic reaction onset as cofactors. The prevalence of GRP sensitization was high in Japanese fruit allergy patients except for PFAS patients. In conclusion, GRP-sensitized patients may have allergies to multiple fruits and may show peculiar characteristics such as facial swelling and cofactor dependence. © 2017 Japanese Dermatological Association.

  19. Kinetics and thermodynamics studies on the BMP-2 adsorption onto hydroxyapatite surface with different multi-morphological features

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Zhiwei; Huangfu, Changxin; Wang, Yanying; Ge, Hongwei; Yao, Yao; Zou, Ping; Wang, Guangtu [College of Science, Sichuan Agricultural University, Ya' an 625014 (China); He, Hua [Institute of Animal Genetics and Breeding, Sichuan Agricultural University, Wenjiang, Sichuan 611130 (China); Rao, Hanbing, E-mail: rhbscu@gmail.com [College of Science, Sichuan Agricultural University, Ya' an 625014 (China)

    2015-07-01

    The effect of the surface topography on protein adsorption process is of great significance for designing hydroxyapatite (HA) ceramic material surfaces. In this work, three different topographies of HA materials HA-sheet, HA-rod, and HA-whisker were synthesized and testified by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Brunauer–Emmett–Teller (BET) and a field emission scanning electron microscopy (FE-SEM). We have systematically investigated the adsorption kinetics and thermodynamics of bone morphogenetic proteins (BMP-2) on the three different topography surfaces of HA, respectively. The results showed that the maximum adsorption capacities of HA-sheet, HA-rod and HA-whisker were (219.96 ± 10.18), (247.13 ± 12.35), and (354.67 ± 17.73) μg · g{sup −1}, respectively. Kinetic parameters, rate constants, equilibrium adsorption capacities and related correlation coefficients, for each kinetic model were calculated as well as discussed. It demonstrated that the adsorption of BMP-2 onto HA could be described by the pseudo second-order equation. Adsorption of BMP-2 onto HA followed the Langmuir isotherm. It confirmed that compared with other samples HA-whisker had more adsorption sites for its high specific surface area which could provide more opportunities for protein molecules. The adsorption processes were endothermic (ΔH > 0), spontaneous (ΔG < 0) and entropy increasing (ΔS > 0). A possible adsorption mechanism has been proposed. In addition, the BMP-2 could be adsorbed to the surface which existed slight conformational changes by FT-IR. - Highlights: • A novel protein adsorption studies based on sheet, rod and whisker of HA were designed. • Kinetic and thermodynamics parameters of BMP-2 and HA bonded materials were evaluated. • Surface topographies of the HA effect BMP-2 adsorption • The HA-whisker material had excellent adsorption performance for protein enrichment. • The electrostatic interaction is responsible for the

  20. Kinetics and thermodynamics studies on the BMP-2 adsorption onto hydroxyapatite surface with different multi-morphological features

    International Nuclear Information System (INIS)

    Lu, Zhiwei; Huangfu, Changxin; Wang, Yanying; Ge, Hongwei; Yao, Yao; Zou, Ping; Wang, Guangtu; He, Hua; Rao, Hanbing

    2015-01-01

    The effect of the surface topography on protein adsorption process is of great significance for designing hydroxyapatite (HA) ceramic material surfaces. In this work, three different topographies of HA materials HA-sheet, HA-rod, and HA-whisker were synthesized and testified by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Brunauer–Emmett–Teller (BET) and a field emission scanning electron microscopy (FE-SEM). We have systematically investigated the adsorption kinetics and thermodynamics of bone morphogenetic proteins (BMP-2) on the three different topography surfaces of HA, respectively. The results showed that the maximum adsorption capacities of HA-sheet, HA-rod and HA-whisker were (219.96 ± 10.18), (247.13 ± 12.35), and (354.67 ± 17.73) μg · g −1 , respectively. Kinetic parameters, rate constants, equilibrium adsorption capacities and related correlation coefficients, for each kinetic model were calculated as well as discussed. It demonstrated that the adsorption of BMP-2 onto HA could be described by the pseudo second-order equation. Adsorption of BMP-2 onto HA followed the Langmuir isotherm. It confirmed that compared with other samples HA-whisker had more adsorption sites for its high specific surface area which could provide more opportunities for protein molecules. The adsorption processes were endothermic (ΔH > 0), spontaneous (ΔG < 0) and entropy increasing (ΔS > 0). A possible adsorption mechanism has been proposed. In addition, the BMP-2 could be adsorbed to the surface which existed slight conformational changes by FT-IR. - Highlights: • A novel protein adsorption studies based on sheet, rod and whisker of HA were designed. • Kinetic and thermodynamics parameters of BMP-2 and HA bonded materials were evaluated. • Surface topographies of the HA effect BMP-2 adsorption • The HA-whisker material had excellent adsorption performance for protein enrichment. • The electrostatic interaction is responsible for the BMP-2