WorldWideScience

Sample records for beryllium workers assessment

  1. Worker Environment Beryllium Characterization Study

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environment, Safety, Health & Quality

    2009-12-28

    This report summarizes the conclusion of regular monitoring of occupied buildings at the Nevada Test Site and North Las Vegas facility to determine the extent of beryllium (Be) contamination in accordance with Judgment of Needs 6 of the August 14, 2003, “Minnema Report.”

  2. Worker Environment Beryllium Characterization Study

    International Nuclear Information System (INIS)

    This report summarizes the conclusion of regular monitoring of occupied buildings at the Nevada Test Site and North Las Vegas facility to determine the extent of beryllium (Be) contamination in accordance with Judgment of Needs 6 of the August 14, 2003, 'Minnema Report.'

  3. Assessment of LANL beryllium waste management documentation

    International Nuclear Information System (INIS)

    The objective of this report is to determine present status of the preparation and implementation of the various high priority documents required to properly manage the beryllium waste generated at the Laboratory. The documents being assessed are: Waste Acceptance Criteria, Waste Characterization Plan, Waste Certification Plan, Waste Acceptance Procedures, Waste Characterization Procedures, Waste Certification Procedures, Waste Training Procedures and Waste Recordkeeping Procedures. Beryllium is regulated (as a dust) under 40 CFR 261.33 as ''Discarded commercial chemical products, off specification species, container residues and spill residues thereof.'' Beryllium is also identified in the 3rd thirds ruling of June 1, 1990 as being restricted from land disposal (as a dust). The beryllium waste generated at the Laboratory is handled separately because beryllium has been identified as a highly toxic carcinogenic material

  4. Technical Basis for PNNL Beryllium Inventory

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Michelle Lynn

    2014-07-09

    The Department of Energy (DOE) issued Title 10 of the Code of Federal Regulations Part 850, “Chronic Beryllium Disease Prevention Program” (the Beryllium Rule) in 1999 and required full compliance by no later than January 7, 2002. The Beryllium Rule requires the development of a baseline beryllium inventory of the locations of beryllium operations and other locations of potential beryllium contamination at DOE facilities. The baseline beryllium inventory is also required to identify workers exposed or potentially exposed to beryllium at those locations. Prior to DOE issuing 10 CFR 850, Pacific Northwest Nuclear Laboratory (PNNL) had documented the beryllium characterization and worker exposure potential for multiple facilities in compliance with DOE’s 1997 Notice 440.1, “Interim Chronic Beryllium Disease.” After DOE’s issuance of 10 CFR 850, PNNL developed an implementation plan to be compliant by 2002. In 2014, an internal self-assessment (ITS #E-00748) of PNNL’s Chronic Beryllium Disease Prevention Program (CBDPP) identified several deficiencies. One deficiency is that the technical basis for establishing the baseline beryllium inventory when the Beryllium Rule was implemented was either not documented or not retrievable. In addition, the beryllium inventory itself had not been adequately documented and maintained since PNNL established its own CBDPP, separate from Hanford Site’s program. This document reconstructs PNNL’s baseline beryllium inventory as it would have existed when it achieved compliance with the Beryllium Rule in 2001 and provides the technical basis for the baseline beryllium inventory.

  5. Low Prevalence of Chronic Beryllium Disease among Workers at a Nuclear Weapons Research and Development Facility

    Energy Technology Data Exchange (ETDEWEB)

    Arjomandi, M; Seward, J P; Gotway, M B; Nishimura, S; Fulton, G P; Thundiyil, J; King, T E; Harber, P; Balmes, J R

    2010-01-11

    To study the prevalence of beryllium sensitization (BeS) and chronic beryllium disease (CBD) in a cohort of workers from a nuclear weapons research and development facility. We evaluated 50 workers with BeS with medical and occupational histories, physical examination, chest imaging with HRCT (N=49), and pulmonary function testing. Forty of these workers also underwent bronchoscopy for bronchoalveolar lavage (BAL) and transbronchial biopsies. The mean duration of employment at the facility was 18 yrs and the mean latency (from first possible exposure) to time of evaluation was 32 yrs. Five of the workers had CBD at the time of evaluation (based on histology or HRCT); three others had evidence of probable CBD. These workers with BeS, characterized by a long duration of potential Be exposure and a long latency, had a low prevalence of CBD.

  6. Long-term follow-up of beryllium sensitized workers from a single employer

    Directory of Open Access Journals (Sweden)

    Curtis Anne M

    2010-01-01

    Full Text Available Abstract Background Up to 12% of beryllium-exposed American workers would test positive on beryllium lymphocyte proliferation test (BeLPT screening, but the implications of sensitization remain uncertain. Methods Seventy two current and former employees of a beryllium manufacturer, including 22 with pathologic changes of chronic beryllium disease (CBD, and 50 without, with a confirmed positive test were followed-up for 7.4 +/-3.1 years. Results Beyond predicted effects of aging, flow rates and lung volumes changed little from baseline, while DLCO dropped 17.4% of predicted on average. Despite this group decline, only 8 subjects (11.1% demonstrated physiologic or radiologic abnormalities typical of CBD. Other than baseline status, no clinical or laboratory feature distinguished those who clinically manifested CBD at follow-up from those who did not. Conclusions The clinical outlook remains favorable for beryllium-sensitized individuals over the first 5-12 years. However, declines in DLCO may presage further and more serious clinical manifestations in the future. These conclusions are tempered by the possibility of selection bias and other study limitations.

  7. Proton irradiation effects on beryllium - A macroscopic assessment

    Science.gov (United States)

    Simos, Nikolaos; Elbakhshwan, Mohamed; Zhong, Zhong; Camino, Fernando

    2016-10-01

    Beryllium, due to its excellent neutron multiplication and moderation properties, in conjunction with its good thermal properties, is under consideration for use as plasma facing material in fusion reactors and as a very effective neutron reflector in fission reactors. While it is characterized by unique combination of structural, chemical, atomic number, and neutron absorption cross section it suffers, however, from irradiation generated transmutation gases such as helium and tritium which exhibit low solubility leading to supersaturation of the Be matrix and tend to precipitate into bubbles that coalesce and induce swelling and embrittlement thus degrading the metal and limiting its lifetime. Utilization of beryllium as a pion production low-Z target in high power proton accelerators has been sought both for its low Z and good thermal properties in an effort to mitigate thermos-mechanical shock that is expected to be induced under the multi-MW power demand. To assess irradiation-induced changes in the thermal and mechanical properties of Beryllium, a study focusing on proton irradiation damage effects has been undertaken using 200 MeV protons from the Brookhaven National Laboratory Linac and followed by a multi-faceted post-irradiation analysis that included the thermal and volumetric stability of irradiated beryllium, the stress-strain behavior and its ductility loss as a function of proton fluence and the effects of proton irradiation on the microstructure using synchrotron X-ray diffraction. The mimicking of high temperature irradiation of Beryllium via high temperature annealing schemes has been conducted as part of the post-irradiation study. This paper focuses on the thermal stability and mechanical property changes of the proton irradiated beryllium and presents results of the macroscopic property changes of Beryllium deduced from thermal and mechanical tests.

  8. Massachusetts Beryllium Screening Program for Former Workers of Wyman-Gordon, Norton Abrasives, and MIT/Nuclear Metals

    Energy Technology Data Exchange (ETDEWEB)

    Pepper, L. D.

    2008-05-21

    The overall objective of this project was to provide medical screening to former workers of Wyman-Gordon Company, Norton Abrasives, and MIT/Nuclear Metals (NMI) in order to prevent and minimize the health impact of diseases caused by site related workplace exposures to beryllium. The program was developed in response to a request by the U.S. Department of Energy (DOE) that had been authorized by Congress in Section 3162 of the 1993 Defense Authorization Act, urging the DOE to carry out a program for the identification and ongoing evaluation of current and former DOE employees who are subjected to significant health risks during such employment." This program, funded by the DOE, was an amendment to the medical surveillance program for former DOE workers at the Nevada Test Site (NTS). This program's scope included workers who had worked for organizations that provided beryllium products or materials to the DOE as part of their nuclear weapons program. These organizations have been identified as Beryllium Vendors.

  9. Assessment of beryllium Faraday screens of the JET ICRF antennas

    International Nuclear Information System (INIS)

    The JET ICRF antennas, equipped with beryllium (Be) Faraday screens (FS), can be operated in such a way that the RF specific effects on the plasma boundary, by the impurity influx originating at the screens, are reduced to a negligible level. In dipole phasing, k parallel = 7 m-1, the influx is for all purposes negligible. In monopole phasing (kparallel = 0 m-1) the beryllium influx does not exceed ΦFSBe = 1 x 1019 atoms·MW-1·s-1 and the corresponding δZeff/PRF is -1. The observed dependences of ΦFSBe (in monopole phasing) on plasma density, antenna voltage, antenna phasing, and the angle between FS elements and the magnetic field in the boundary, B-vector(a) = B-vectorθ(a) + B-vectorT(a), confirm that the release mechanism is sputtering by ions accelerated in the RF enhanced Bohm-Debye sheaths forming at the front face of the FS. When the angle between FS and B-vector(a) is approx. 22 deg. C, the fraction of the RF power radiated by the antenna, dissipated at the screen, can reach 40%. At high antenna voltage, arcing across the FS can occur. With dipole phasing the heating efficiency is not degraded, even with the large angle, and all the power coupled by the antenna is absorbed at the resonance position near the plasma centre. The open screen design did not introduce any disadvantages. The experience from JET operation at powers of up to 22 MW shows that, if the necessary conditions are met, i.e. if RF rectification is minimized, antennas are phased as dipoles and material with low sputtering coefficients at energies of 0.5-1 keV is used, then the influx from the FS is, for all practical purposes, eliminated. (author). 19 refs, 6 figs

  10. An occurrence model for the national assessment of volcanogenic beryllium deposits

    Science.gov (United States)

    Foley, Nora K.; Seal, Robert R., II; Piatak, Nadine M.; Hetland, Brianna

    2010-01-01

    The general occurrence model summarized here is intended to provide a descriptive basis for the identification and assessment of undiscovered beryllium deposits of a type and style similar to those found at Spor Mountain, Juab County, Utah. The assessment model is restricted in its application in order to provide a coherent basis for assessing the probability of the occurrence of similar economic deposits using the current U.S. Geological Survey methodology. The model is intended to be used to identify tracts of land where volcanogenic epithermal replacement-type beryllium deposits hosted by metaluminous to peraluminous rhyolite are most likely to occur. Only a limited number of deposits or districts of this type are known, and only the ores of the Spor Mountain district have been studied in detail. The model highlights those distinctive aspects and features of volcanogenic epithermal beryllium deposits that pertain to the development of assessment criteria and puts forward a baseline analysis of the geoenvironmental consequences of mining deposits of this type.

  11. Beryllium 1989

    Energy Technology Data Exchange (ETDEWEB)

    1989-01-01

    The Roskill report on beryllium gives information on the occurrence and reserves, production technology, geographic distribution, consumption and end-uses, stocks, prices and beryllium and health. There is an appendix on international trade statistics. (author).

  12. Aerosols generated during beryllium machining.

    Science.gov (United States)

    Martyny, J W; Hoover, M D; Mroz, M M; Ellis, K; Maier, L A; Sheff, K L; Newman, L S

    2000-01-01

    Some beryllium processes, especially machining, are associated with an increased risk of beryllium sensitization and disease. Little is known about exposure characteristics contributing to risk, such as particle size. This study examined the characteristics of beryllium machining exposures under actual working conditions. Stationary samples, using eight-stage Lovelace Multijet Cascade Impactors, were taken at the process point of operation and at the closest point that the worker would routinely approach. Paired samples were collected at the operator's breathing zone by using a Marple Personal Cascade Impactor and a 35-mm closed-faced cassette. More than 50% of the beryllium machining particles in the breathing zone were less than 10 microns in aerodynamic diameter. This small particle size may result in beryllium deposition into the deepest portion of the lung and may explain elevated rates of sensitization among beryllium machinists.

  13. Defense programs beryllium good practice guide

    International Nuclear Information System (INIS)

    Within the DOE, it has recently become apparent that some contractor employees who have worked (or are currently working) with and around beryllium have developed chronic beryllium disease (CBD), an occupational granulomatous lung disorder. Respiratory exposure to aerosolized beryllium, in susceptible individuals, causes an immunological reaction that can result in granulomatous scarring of the lung parenchyma, shortness of breath, cough, fatigue, weight loss, and, ultimately, respiratory failure. Beryllium disease was originally identified in the 1940s, largely in the fluorescent light industry. In 1950, the Atomic Energy Commission (AEC) introduced strict exposure standards that generally curtailed both the acute and chronic forms of the disease. Beginning in 1984, with the identification of a CBD case in a DOE contractor worker, there was increased scrutiny of both industrial hygiene practices and individuals in this workforce. To date, over 100 additional cases of beryllium-specific sensitization and/or CBD have been identified. Thus, a disease previously thought to be largely eliminated by the adoption of permissible exposure standards 45 years ago is still a health risk in certain workforces. This good practice guide forms the basis of an acceptable program for controlling workplace exposure to beryllium. It provides (1) Guidance for minimizing worker exposure to beryllium in Defense Programs facilities during all phases of beryllium-related work, including the decontamination and decommissioning (D ampersand D) of facilities. (2) Recommended controls to be applied to the handling of metallic beryllium and beryllium alloys, beryllium oxide, and other beryllium compounds. (3) Recommendations for medical monitoring and surveillance of workers exposed (or potentially exposed) to beryllium, based on the best current understanding of beryllium disease and medical diagnostic tests available. (4) Site-specific safety procedures for all processes of beryllium that is

  14. Beryllium Toxicity

    Science.gov (United States)

    ... Favorites Del.icio.us Digg Facebook Google Bookmarks Yahoo MyWeb Beryllium Toxicity Patient Education Care Instruction Sheet ... Favorites Del.icio.us Digg Facebook Google Bookmarks Yahoo MyWeb Page last reviewed: May 23, 2008 Page ...

  15. Postural stability assessment in sewer workers.

    Science.gov (United States)

    Kuo, W; Bhattacharya, A; Succop, P; Linz, D

    1996-01-01

    In this study, postural stability was measured with a microcomputer-based force platform as an indirect assessment of central nervous system effect in 28 sewer workers (age range 23.4 to 64.5 years, standard deviation of 8.7 years). All workers performed four 30-second postural sway tests. The organic-solvent exposure was measured by a photo-ionization detector. The photo-ionization detector was calibrated to measure volatile organic solvents in total benzene equivalence, and concentrations were measured in various parts of the plant. The mean exposure was .32 parts per million (ppm) benzene equivalent (range of .02 to .95 ppm, standard deviation .19 ppm). Based on a covariate adjusted linear multiple-regression model, a statistically significant (p organic-solvent exposure. These workers also had increased postural sway compared with a nonexposed population. The statistically significant correlation between postural sway determinations and organic-solvent exposure was surprising given the very low exposures measured. It is possible that the organic-solvent exposure might not be the causative agent, but rather that the solvents themselves correlate with some other causative exposure, ie, total volatile organics as implicated in the cause of sick-building syndrome.

  16. Beryllium assessment and recommendation for application in ITER plasma facing components

    Energy Technology Data Exchange (ETDEWEB)

    Barabash, V.; Tanaka, S.; Matera, R. [ITER Joint Central Team, Muenchen (Germany)

    1998-01-01

    The design status of the ITER Plasma Facing Components (PFC) is presented. The operational conditions of the armour material for the different components are summarized. Beryllium is the reference armour material for the Primary Wall, Baffle and Limiter and the back-up material for the Divertor Dome. The activities on the selection of the Be grades and the joining technologies are reviewed. (author)

  17. Defense programs beryllium good practice guide

    Energy Technology Data Exchange (ETDEWEB)

    Herr, M.

    1997-07-01

    Within the DOE, it has recently become apparent that some contractor employees who have worked (or are currently working) with and around beryllium have developed chronic beryllium disease (CBD), an occupational granulomatous lung disorder. Respiratory exposure to aerosolized beryllium, in susceptible individuals, causes an immunological reaction that can result in granulomatous scarring of the lung parenchyma, shortness of breath, cough, fatigue, weight loss, and, ultimately, respiratory failure. Beryllium disease was originally identified in the 1940s, largely in the fluorescent light industry. In 1950, the Atomic Energy Commission (AEC) introduced strict exposure standards that generally curtailed both the acute and chronic forms of the disease. Beginning in 1984, with the identification of a CBD case in a DOE contractor worker, there was increased scrutiny of both industrial hygiene practices and individuals in this workforce. To date, over 100 additional cases of beryllium-specific sensitization and/or CBD have been identified. Thus, a disease previously thought to be largely eliminated by the adoption of permissible exposure standards 45 years ago is still a health risk in certain workforces. This good practice guide forms the basis of an acceptable program for controlling workplace exposure to beryllium. It provides (1) Guidance for minimizing worker exposure to beryllium in Defense Programs facilities during all phases of beryllium-related work, including the decontamination and decommissioning (D&D) of facilities. (2) Recommended controls to be applied to the handling of metallic beryllium and beryllium alloys, beryllium oxide, and other beryllium compounds. (3) Recommendations for medical monitoring and surveillance of workers exposed (or potentially exposed) to beryllium, based on the best current understanding of beryllium disease and medical diagnostic tests available. (4) Site-specific safety procedures for all processes of beryllium that is likely to

  18. Assessment of irradiation effects on beryllium reflector and heavy water tank of JRR-3M

    Energy Technology Data Exchange (ETDEWEB)

    Murayama, Yoji; Kakehuda, Kazuhiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-10-01

    The JRR-3M, a swimming pool type research reactor with beryllium and heavy water reflectors, has been operated since 1990. Since the beryllium reflectors are close to fuel and receive high fast neutron fluence in a relatively short time, they may be subject to change their dimensions by swelling due mostly to entrapped helium gaseous. This may bend the reflectors to the outside and narrow gaps between the reflectors and the fuel elements. The gaps have been measured with an ultrasonic thickness gage in an annual inspection. The results in 1996 show that the maximum of expansion in the diametral directions was 0.6 mm against 1.6 mm of a managed value for replacement of the reflector. A heavy water tank of the JRR-3M is made of aluminum alloy A5052. Surveillance tests of the alloy have been conducted to evaluate irradiation effects of the heavy water tank. Five sets of specimens of the alloy have been irradiated in the beryllium reflectors where fast neutron flux is higher than that in the heavy water tank. In 1994, one set of specimens had been unloaded and carried out the post-irradiation tests. The results show that the heavy water tank preserved satisfactory mechanical properties. (author)

  19. Lay Outreach Workers and the Ohio Migrant and Seasonal Farm Workers Health Education Needs Assessment.

    Science.gov (United States)

    Alvarez, Olga L.

    The Migrant and Seasonal Farm Workers Project sought to determine the health education needs of this indigent population in Ohio using the help of lay outreach workers. A bilingual needs assessment survey was developed containing questions on demographics, place of permanent residence, points of travel after working in Ohio, and type of work and…

  20. Assessment of cardiometabolic risk among shift workers in Hungary

    Directory of Open Access Journals (Sweden)

    Jermendy György

    2012-02-01

    Full Text Available Abstract Aim Shift workers may be at risk of different diseases. In order to assess cardiometabolic risk in shift workers, a cross-sectional study was performed among active workers. Methods A total of 481 workers (121 men, 360 women were investigated; most of them were employees in light industry (58.2% or in public services (23.9%. Past medical history was recorded and physical examination was performed. Questionnaires were used to characterize daily activity. Fasting venous blood sample was collected for measuring laboratory parameters. Data from shift workers (n = 234, age: 43.9 ± 8.1 years were compared to those of daytime workers (n = 247, age: 42.8 ± 8.5 years, men and women were analyzed separately. Results In men, systolic blood pressure was higher in shift workers compared to daytime workers (133 ± 8 vs 126 ± 17 mmHg; p vs 67.7 ± 13.2 kg; p vs 13.4%; p vs 21.7%; p vs 1.68 ± 0.36 mmol/l; p Conclusion Middle-aged active shift workers, especially women, have a less healthy lifestyle and are at higher cardiometabolic risk as compared to daytime workers. Our study highlights the importance of measures for identifying and preventing cardiometabolic risk factors in shift workers.

  1. Assessment of worker and nonworker radiological safety of a repository

    International Nuclear Information System (INIS)

    Preliminary assessments of worker and nonworker radiological safety for both normal and accident conditions during the preclosure period have been performed for the proposed Yucca Mountain repository. The accident-conditions assessment estimated off-site doses resulting form credible accidents at the repository. Since the purpose of the accident-conditions assessment was to support the development of an initial Q list, worker doses were not calculated. The normal-conditions assessment estimated off-site public doses as well as on-site worker doses resulting form the various anticipated routine radioactive releases and sources. The purpose of the normal-conditions assessment was to evaluate the preliminary Yucca Mountain repository design and identify those operations and aspects that are most important to radiation safety for the repository (e.g., those operations that are the largest contributors to the occupational doses of individual workers). The general approach and some of the results of these safety assessments are summarized

  2. OVERVIEW OF BERYLLIUM SAMPLING AND ANALYSIS

    Energy Technology Data Exchange (ETDEWEB)

    Brisson, M

    2009-04-01

    Because of its unique properties as a lightweight metal with high tensile strength, beryllium is widely used in applications including cell phones, golf clubs, aerospace, and nuclear weapons. Beryllium is also encountered in industries such as aluminium manufacturing, and in environmental remediation projects. Workplace exposure to beryllium particulates is a growing concern, as exposure to minute quantities of anthropogenic forms of beryllium may lead to sensitization and to chronic beryllium disease, which can be fatal and for which no cure is currently known. Furthermore, there is no known exposure-response relationship with which to establish a 'safe' maximum level of beryllium exposure. As a result, the current trend is toward ever lower occupational exposure limits, which in turn make exposure assessment, both in terms of sampling and analysis, more challenging. The problems are exacerbated by difficulties in sample preparation for refractory forms of beryllium, such as beryllium oxide, and by indications that some beryllium forms may be more toxic than others. This chapter provides an overview of sources and uses of beryllium, health risks, and occupational exposure limits. It also provides a general overview of sampling, analysis, and data evaluation issues that will be explored in greater depth in the remaining chapters. The goal of this book is to provide a comprehensive resource to aid personnel in a wide variety of disciplines in selecting sampling and analysis methods that will facilitate informed decision-making in workplace and environmental settings.

  3. Exposure Assessment of Workers Handling Industrial NORM in Japan

    International Nuclear Information System (INIS)

    In the study, a dose assessment of workers handling typical industrial NORM was carried out to obtain information for the future regulation system in Japan. The annual effective dose received by workers was estimated using measurements of dose rate and activity concentrations in raw materials, products and aerosols, as well as concentrations of 222Rn and 220Rn decay products in workplaces at plants processing zircon, monazite and titanium ore in Japan. From the results of the dose assessment, a relationship between the concentration of NORM and the average annual dose received by the worker was discussed. (author)

  4. Occurrence model for volcanogenic beryllium deposits: Chapter F in Mineral deposit models for resource assessment

    Science.gov (United States)

    Foley, Nora K.; Hofstra, Albert H.; Lindsey, David A.; Seal, Robert R., II; Jaskula, Brian W.; Piatak, Nadine M.

    2012-01-01

    Current global and domestic mineral resources of beryllium (Be) for industrial uses are dominated by ores produced from deposits of the volcanogenic Be type. Beryllium deposits of this type can form where hydrothermal fluids interact with fluorine and lithophile-element (uranium, thorium, rubidium, lithium, beryllium, cesium, tantalum, rare earth elements, and tin) enriched volcanic rocks that contain a highly reactive lithic component, such as carbonate clasts. Volcanic and hypabyssal high-silica biotite-bearing topaz rhyolite constitutes the most well-recognized igneous suite associated with such Be deposits. The exemplar setting is an extensional tectonic environment, such as that characterized by the Basin and Range Province, where younger topaz-bearing igneous rock sequences overlie older dolomite, quartzite, shale, and limestone sequences. Mined deposits and related mineralized rocks at Spor Mountain, Utah, make up a unique economic deposit of volcanogenic Be having extensive production and proven and probable reserves. Proven reserves in Utah, as reported by the U.S. Geological Survey National Mineral Information Center, total about 15,900 tons of Be that are present in the mineral bertrandite (Be4Si2O7(OH)2). At the type locality for volcanogenic Be, Spor Mountain, the tuffaceous breccias and stratified tuffs that host the Be ore formed as a result of explosive volcanism that brought carbonate and other lithic fragments to the surface through vent structures that cut the underlying dolomitic Paleozoic sedimentary rock sequences. The tuffaceous sediments and lithic clasts are thought to make up phreatomagmatic base surge deposits. Hydrothermal fluids leached Be from volcanic glass in the tuff and redeposited the Be as bertrandite upon reaction of the hydrothermal fluid with carbonate clasts in lithic-rich sections of tuff. The localization of the deposits in tuff above fluorite-mineralized faults in carbonate rocks, together with isotopic evidence for the

  5. Occupational risk assessment of paint industry workers

    Directory of Open Access Journals (Sweden)

    Hugo M de Oliveira

    2011-01-01

    Full Text Available Background: Thousands of chemical compounds are used in paint products, like pigments, extenders, binders, additives, and solvents (toluene, xylene, ketones, alcohols, esters, and glycol ethers. Paint manufacture workers are potentially exposed to the chemicals present in paint products although the patterns and levels of exposure to individual agents may differ from those of painters. The aim of the present study was to evaluate genome damage induced in peripheral blood lymphocytes and oral mucosa cells of paint industry workers. Materials and Methods: Genotoxicity was evaluated using the alkaline Comet assay in blood lymphocytes and oral mucosa cells, and the Micronucleus test in oral mucosa cells. For the micronucleus test in exfoliated buccal cells, no significant difference was detected between the control and paint industry workers. Results: The Comet assay in epithelia buccal cells showed that the damage index (DI and damage frequency (DF observed in the exposed group were significantly higher relative to the control group ( P≤0.05. In the same way, the Comet assay data in peripheral blood leukocytes showed that both analysis parameters (DI and DF were significantly greater than that for the control group ( P≤0.05. Conclusions: Chronic occupational exposure to paints may lead to a slightly increased risk of genetic damage among paint industry workers.

  6. Potential exposures and risks from beryllium-containing products.

    Science.gov (United States)

    Willis, Henry H; Florig, H Keith

    2002-10-01

    Beryllium is the strongest of the lightweight metals. Used primarily in military applications prior to the end of the Cold War, beryllium is finding new applications in many commercial products, including computers, telecommunication equipment, and consumer and automotive electronics. The use of beryllium in nondefense consumer applications is of concern because beryllium is toxic. Inhalation of beryllium dust or vapor causes a chronic lung disease in some individuals at concentrations as low as 0.01 microg/m3 in air. As beryllium enters wider commerce, it is prudent to ask what risks this might present to the general public and to workers downstream of the beryllium materials industry. We address this question by evaluating the potential for beryllium exposure from the manufacturing, use, recycle, and disposal of beryllium-containing products. Combining a market study with a qualitative exposure analysis, we determine which beryllium applications and life cycle phases have the largest exposure potential. Our analysis suggests that use and maintenance of the most common types of beryllium-containing products do not result in any obvious exposures of concern, and that maintenance activities result in greater exposures than product use. Product disposal has potential to present significant individual risks, but uncertainties concerning current and future routes of product disposal make it difficult to be definitive. Overall, additional exposure and dose-response data are needed to evaluate both the health significance of many exposure scenarios, and the adequacy of existing regulations to protect workers and the public. Although public exposures to beryllium and public awareness and concern regarding beryllium risks are currently low, beryllium risks have psychometric qualities that may lead to rapidly heightened public concern. PMID:12442995

  7. CANISTER HANDLING FACILITY WORKER DOSE ASSESSMENT

    Energy Technology Data Exchange (ETDEWEB)

    D.T. Dexheimer

    2004-02-27

    The purpose of this calculation is to estimate radiation doses received by personnel working in the Canister Handling Facility (CHF) performing operations to receive transportation casks, transfer wastes, prepare waste packages, perform associated equipment maintenance. The specific scope of work contained in this calculation covers individual worker group doses on an annual basis, and includes the contributions due to external and internal radiation. The results of this calculation will be used to support the design of the CHF and provide occupational dose estimates for the License Application.

  8. CANISTER HANDLING FACILITY WORKER DOSE ASSESSMENT

    International Nuclear Information System (INIS)

    The purpose of this calculation is to estimate radiation doses received by personnel working in the Canister Handling Facility (CHF) performing operations to receive transportation casks, transfer wastes, prepare waste packages, perform associated equipment maintenance. The specific scope of work contained in this calculation covers individual worker group doses on an annual basis, and includes the contributions due to external and internal radiation. The results of this calculation will be used to support the design of the CHF and provide occupational dose estimates for the License Application

  9. FUEL HANDLING FACILITY WORKER DOSE ASSESSMENT

    International Nuclear Information System (INIS)

    The purpose of this design calculation is to estimate radiation doses received by personnel working in the Fuel Handling Facility (FHF) of the Monitored Geological Repository (MGR). The FHF is a surface facility supporting waste handling operations i.e. receive transportation casks, transfer wastes, prepare waste packages, and ship out loaded waste packages and empty casks. The specific scope of work contained in this calculation covers both collective doses and individual worker group doses on an annual basis, and includes the contributions due to external and internal radiation. The results are also limited to normal operations only. Results of this calculation will be used to support the FHF design and License Application

  10. Monitoring beryllium during site cleanup and closure using a real-time analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Schlager, R.J.; Sappey, A.D.; French, P.D. [ADA Technologies, Inc., Englewood, CO (United States)

    1998-12-31

    Beryllium metal has a number of unique properties that have been exploited for use in commercial and government applications. Airborne beryllium particles can represent a significant human health hazard if deposited in the lungs. These particles can cause immunologically-mediated chronic granulomatous lung disease (chronic beryllium disease). Traditional methods of monitoring airborne beryllium involve collecting samples of air within the work area using a filter. The filter then undergoes chemical analysis to determine the amount of beryllium collected during the sampling period. These methods are time-consuming and results are known only after a potential exposure has occurred. The need for monitoring exposures in real time has prompted government and commercial companies to develop instrumentation that will allow for the real time assessment of short-term exposures so that adequate protection for workers in contaminated environments can be provided. Such an analyzer provides a tool that will allow government and commercial sites to be cleaned up in a more safe and effective manner since exposure assessments can be made instantaneously. This paper describes the development and initial testing of an analyzer for monitoring airborne beryllium using a technique known as Laser-Induced Breakdown Spectroscopy (LIBS). Energy from a focused, pulsed laser is used to vaporize a sample and create an intense plasma. The light emitted from the plasma is analyzed to determine the quantity of beryllium in the sampled air. A commercial prototype analyzer has been fabricated and tested in a program conducted by Lawrence Livermore National Laboratory, Los Alamos National Laboratory, Lovelace Respiratory Research Institute, and ADA Technologies, Inc. Design features of the analyzer and preliminary test results are presented.

  11. DRY TRANSFER FACILITY WORKER DOSE ASSESSMENT

    International Nuclear Information System (INIS)

    The purpose of this calculation is to estimate radiation doses received by personnel working in the Dry Transfer Facility No.1 (DTF-1) performing operations to receive transportation casks, transfer wastes, prepare waste packages, and ship out loaded waste packages and empty casks. Doses received by workers due to maintenance operations are also included in this revision. The specific scope of work contained in this calculation covers both collective doses and individual worker group doses on an annual basis, and includes the contributions due to external and internal radiation from normal operation, excluding the remediation area of the building. The results of this calculation will be used to support the design of the DTF-1 and to provide occupational dose estimates for the License Application. The calculations contained in this document were developed by Environmental and Nuclear Engineering of the Design and Engineering Organization and are intended solely for the use of the Design and Engineering Organization in its work regarding facility operation. Yucca Mountain Project personnel from the Environmental and Nuclear Engineering should be consulted before use of the calculations for purposes other than those stated herein or use by individuals other than authorized personnel in the Environmental and Nuclear Engineering

  12. Beryllium facilities in India

    International Nuclear Information System (INIS)

    Due to its unique combination of physical, mechanical, thermal and nuclear properties, beryllium is indispensable for many applications in the fields of nuclear and space sciences. Beryllia and copper beryllium alloys have also found extensive applications in the electrical and electronic industries. Beryllium facilities at Bhabha Atomic Research Centre (BARC) have been set up to meet indigenous requirements for these materials. Besides developing beryllium technology, the project team has also designed and developed a number of special purpose equipment. (Author)

  13. Ergonomic Risk Assessment on Oil Palm Industry Workers

    Directory of Open Access Journals (Sweden)

    Baba Mohd DEROS

    2016-03-01

    Full Text Available Background: This study was an investigation conducted at two oil palm plantations in Slim River District, Perak, Malaysia on the prevalence of back pain among workers in the Malaysian oil palm industry. Many manual handling activities and tasks performed were not designed ergonomically, thus a high prevalence of musculoskeletal disorders was found among oil palm fresh fruit bunches (FFBs manual workers. The three main objectives of this study were to determine the level of employee awareness on health and safety of manual handling tasks; to recognize the musculoskeletal symptom on the workers body parts; and to analyze their working postures and identify the relevant risk factors.Methods: Modified Nordic questionnaire was used to collect data in 2012 at two oil palm plantations located in Slim River District, Perak, Malaysia. Later, Rapid Entire Body Assessment (REBA analysis was conducted for high risk working postures. Seventy workers participated in the study.Results: 81.4% of workers were aware on the correct methods to perform the manual handling tasks. The upper back and lower back pain were experienced by 87.1% and 94.3% of the workers respectively.Conclusion: Manual workers have high level (81.4% health and safety awareness on manual handling tasks but failed to practice it. As a result, 87.1% of them are sufferring from lower back and 94.3% from upper back pain. FFBs loading activity into the lorry is a high risk and changes needed to be done immediately. The two major risk factors identified were awkward lifting postures and repetitive lifting of FFBs. Keywords: Oil palm industry, Ergonomics, Posture, Musculoskeletal pain, workers

  14. Safety handling of beryllium for fusion technology R and D

    International Nuclear Information System (INIS)

    Feasibility of beryllium use as a blanket neutron multiplier, first wall and plasma facing material has been studied for the D-T burning experiment reactors such as ITER. Various experimental work of beryllium and its compounds will be performed under the conditions of high temperature and high energy particle exposure simulating fusion reactor conditions. Beryllium is known as a hazardous substance and its handling has been carefully controlled by various health and safe guidances and/or regulations in many countries. Japanese regulations for hazardous substance provide various guidelines on beryllium for the protection of industrial workers and environment. This report was prepared for the safe handling of beryllium in a laboratory scale experiments for fusion technology R and D such as blanket development. Major items in this report are; (1) Brief review of guidances and regulations in USA, UK and Japan. (2) Safe handling and administration manuals at beryllium facilities in INEL, LANL and JET. (3) Conceptual design study of beryllium handling facility for small to mid-scale blanket R and D. (4) Data on beryllium toxicity, example of clinical diagnosis of beryllium disease, and environmental occurence of beryllium. (5) Personnel protection tools of Japanese Industrial Standard for hazardous substance. (author) 61 refs

  15. Beryllium Related Matter

    Energy Technology Data Exchange (ETDEWEB)

    Gaylord, R F

    2008-12-23

    In recent months, LLNL has identified, commenced, and implemented a series of interim controls, compensatory measures, and initiatives to ensure worker safety, and improve safety processes with regards to potential worker exposure to beryllium. Many of these actions have been undertaken in response to the NNSA Independent Review (COR-TS-5/15/2008-8550) received by LLNL in November of 2008. Others are the result of recent discoveries, events or incidents, and lessons learned, or were scheduled corrective actions from earlier commitments. Many of these actions are very recent in nature, or are still in progress, and vary in the formality of implementation. Actions are being reviewed for effectiveness as they progress. The documentation of implementation, and review of effectiveness, when appropriate, of these actions will be addressed as part of the formal Corrective Action Plan addressing the Independent Review. The mitigating actions taken fall into the following categories: (1) Responses to specific events/concerns; (2) Development of interim controls; (3) Review of ongoing activities; and (4) Performance improvement measures.

  16. Beryllium chemistry and processing

    CERN Document Server

    Walsh, Kenneth A

    2009-01-01

    This book introduces beryllium; its history, its chemical, mechanical, and physical properties including nuclear properties. The 29 chapters include the mineralogy of beryllium and the preferred global sources of ore bodies. The identification and specifics of the industrial metallurgical processes used to form oxide from the ore and then metal from the oxide are thoroughly described. The special features of beryllium chemistry are introduced, including analytical chemical practices. Beryllium compounds of industrial interest are identified and discussed. Alloying, casting, powder processing, forming, metal removal, joining and other manufacturing processes are covered. The effect of composition and process on the mechanical and physical properties of beryllium alloys assists the reader in material selection. The physical metallurgy chapter brings conformity between chemical and physical metallurgical processing of beryllium, metal, alloys, and compounds. The environmental degradation of beryllium and its all...

  17. Coal worker's pneumoconiosis: CT assessment in exposed workers and correlation with radiographic findings

    International Nuclear Information System (INIS)

    To study the signs of coal worker's pneumoconiosis (CWP) at computed tomography (CT), the authors obtained thoracic CT scans in 170 coal-dust-exposed workers who were concomitantly evaluated with conventional posteroanterior and lateral radiography. The profusion and extent of disease was assessed by means of CT in two groups of miners: group 1 (n = 86), miners with worker's compensation and radiographic evidence of CWP, and group 2(n = 84), miners who had applied for compensation without radiographic evidence of CWP. The CT signs of CWP consisted of micronodules, nodules, and progressive massive fibrosis. The comparative analysis demonstrates the superiority of an optimal CT technique over chest radiography in the evaluation of simple silicosis, with improved sensitivity in the detection of small parenchymal opacities. CT provides additional information on the stage of the disease but also clarifies some ambiguities of the ILO classification of small opacities. CT was equivalent to radiography for complicated silicosis, except in the identification of necrosis. CT evaluations are complementary to plain radiography in the assessment of CWP, and the addition of high-resolution CT is useful in achieving a more accurate evaluation of the small parenchymal opacities

  18. Assessing the first wave of epidemiological studies of nanomaterial workers

    International Nuclear Information System (INIS)

    The results of early animal studies of engineered nanomaterials (ENMs) and air pollution epidemiology suggest that it is important to assess the health of ENM workers. Initial epidemiological studies of workers’ exposure to ENMs (<100 nm) are reviewed and characterized for their study designs, findings, and limitations. Of the 15 studies, 11 were cross-sectional, 4 were longitudinal (1 was both cross-sectional and longitudinal in design), and 1 was a descriptive pilot study. Generally, the studies used biologic markers as the dependent variables. All 11 cross-sectional studies showed a positive relationship between various biomarkers and ENM exposures. Three of the four longitudinal studies showed a negative relationship; the fourth showed positive findings after a 1-year follow-up. Each study considered exposure to ENMs as the independent variable. Exposure was assessed by mass concentration in 10 studies and by particle count in six studies. Six of them assessed both mass and particle concentrations. Some of the studies had limited exposure data because of inadequate exposure assessment. Generally, exposure levels were not very high in comparison to those in human inhalation chamber studies, but there were some exceptions. Most studies involved a small sample size, from 2 to 258 exposed workers. These studies represent the first wave of epidemiological studies of ENM workers. They are limited by small numbers of participants, inconsistent (and in some cases inadequate) exposure assessments, generally low exposures, and short intervals between exposure and effect. Still, these studies are a foundation for future work; they provide insight into where ENM workers are experiencing potentially adverse effects that might be related to ENM exposures

  19. Assessing the first wave of epidemiological studies of nanomaterial workers

    Energy Technology Data Exchange (ETDEWEB)

    Liou, Saou-Hsing, E-mail: shliou@nhri.org.tw [National Health Research Institutes, National Institute of Environmental Health Sciences (China); Tsai, Candace S. J. [Colorado State University, Department of Environmental and Radiological Health Science (United States); Pelclova, Daniela [Charles University in Prague, Department of Occupational Medicine, First Faculty of Medicine (Czech Republic); Schubauer-Berigan, Mary K.; Schulte, Paul A. [National Institute for Occupational Safety and Health (United States)

    2015-10-15

    The results of early animal studies of engineered nanomaterials (ENMs) and air pollution epidemiology suggest that it is important to assess the health of ENM workers. Initial epidemiological studies of workers’ exposure to ENMs (<100 nm) are reviewed and characterized for their study designs, findings, and limitations. Of the 15 studies, 11 were cross-sectional, 4 were longitudinal (1 was both cross-sectional and longitudinal in design), and 1 was a descriptive pilot study. Generally, the studies used biologic markers as the dependent variables. All 11 cross-sectional studies showed a positive relationship between various biomarkers and ENM exposures. Three of the four longitudinal studies showed a negative relationship; the fourth showed positive findings after a 1-year follow-up. Each study considered exposure to ENMs as the independent variable. Exposure was assessed by mass concentration in 10 studies and by particle count in six studies. Six of them assessed both mass and particle concentrations. Some of the studies had limited exposure data because of inadequate exposure assessment. Generally, exposure levels were not very high in comparison to those in human inhalation chamber studies, but there were some exceptions. Most studies involved a small sample size, from 2 to 258 exposed workers. These studies represent the first wave of epidemiological studies of ENM workers. They are limited by small numbers of participants, inconsistent (and in some cases inadequate) exposure assessments, generally low exposures, and short intervals between exposure and effect. Still, these studies are a foundation for future work; they provide insight into where ENM workers are experiencing potentially adverse effects that might be related to ENM exposures.

  20. Assessing Oral Cancer Awareness Among Rural Latino Migrant Workers.

    Science.gov (United States)

    Dodd, Virginia J; Schenck, David P; Chaney, Elizabeth H; Padhya, Tapan

    2016-06-01

    Latino migrant farm workers suffer significant health disparities, including poor oral health. The purpose of this research was to assess Latino migrant farm workers' OC awareness, including knowledge and care-seeking behaviors. A 42-item survey was developed. Trained, bilingual researchers verbally administered the survey to migrant farm workers in Hillsborough County, Florida. Frequencies and descriptive statistics were generated to report baseline data. The sample consisted of 53.7 % female respondents. The mean age for males and females respectively was 38.7 and 39.2. Most respondents had attended grade school; 6.7 % never attended school. Perceptions of cancer susceptibility were present; knowledge of OC risk factors, signs and symptoms was low. Participants were unlikely to seek preventive care. The results contribute to the limited studies regarding Latino migrant farm workers and oral cancer risk factor awareness and knowledge. Findings highlight factors influencing motivation and care-seeking behaviors, as well as provide guidance for development of educational materials. PMID:26018959

  1. Beryllium Desorption from Sediments

    Science.gov (United States)

    Boschi, V.; Willenbring, J. K.

    2015-12-01

    Beryllium isotopes have provided a useful tool in the field of geochronology and geomorphology over the last 25 years. The amount of cosmogenic meteoric 10Be and native 9Be absorbed to soils often scales with the residence time and chemical weathering of sediments in a landscape, respectively. Thus, the concentrations in river sediment may be used to quantify the denudation of specific watersheds. When deposited in ocean sediment, these concentrations are thought to record the history of denudation on Earth over the last ~10 Ma. The use of both isotopes often relies on the premise of beryllium retention to sediment surfaces in order to preserve a landscape's erosion and weathering signature. Changes in setting, en route from the soil to fluvial system to the ocean, can cause beryllium desorption and may preclude some applications of the 10Be/9Be system. Four mechanisms were tested to determine the desorption potential of beryllium including a reduction in pH, an increase in ionic strength and complexation with soluble organic and inorganic species. These processes have the potential to mobilize beryllium into solution. For example, by both reducing the pH and increasing the ionic strength, competition for adsorption sites increases, potentially liberating beryllium from the sediment surface. In addition, organic and inorganic ligands can complex beryllium causing it to become mobilized. To determine which of these alterations influence beryllium desorption and to quantify the effect, we prepared separate solutions of beryllium bound to minerals and organic compounds and measured beryllium concentrations in solution before and after adjusting the pH, ionic strength, and changing inorganic and organic ligand concentrations. We conclude from our observations that overall, beryllium sorbed to organic compounds was more resistant to desorption relative to mineral-associated beryllium. Among the methods tested, a reduction in pH resulted in the greatest amount of

  2. Beryllium Health and Safety Committee Data Reporting Task Force

    Energy Technology Data Exchange (ETDEWEB)

    MacQueen, D H

    2007-02-21

    On December 8, 1999, the Department of Energy (DOE) published Title 10 CFR 850 (hereafter referred to as the Rule) to establish a chronic beryllium disease prevention program (CBDPP) to: {sm_bullet} reduce the number of workers currently exposed to beryllium in the course of their work at DOE facilities managed by DOE or its contractors, {sm_bullet} minimize the levels of, and potential for, expos exposure to beryllium, and {sm_bullet} establish medical surveillance requirements to ensure early detection of the disease.

  3. Assessment of soil contamination. Measuring devices for arsenic, berryllium, lead, cadmium, mercury and selenium. Wirkung von Bodenkontaminationen. Messlatten fuer Arsen, Beryllium, Blei, Cadmium, Quecksilber und Selen

    Energy Technology Data Exchange (ETDEWEB)

    Blumenbach, D.; Kloke, A.; Luehr, H.P.

    1991-12-01

    To assess soil contamination with respect to the suitability of the site concerned, it is essential to obtain knowledge of the relationship between soil contamination levels and the effect of the contaminants on a targets meriting protection (e.g. human beings, plants, soil organisms). In this final report, data obtained from literature on the inorganic pollutants arsenic, lead, cadmium, mercury, selenium and beryllium are compiled, and for selected targets an overview is given of the damage occurring at the various concentration levels studies. The present data, together with information on the envisaged use of the site and on soil properties influencing the pollutant's transport to the protected target, can be used to assess soil quality. Threshold values for use in decision-making cannot be derived directly from the presented data, as such data can only convey a picture of the range of the harmful concentrations given in the literature. (orig.).

  4. Beryllium Manufacturing Processes

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, A

    2006-06-30

    This report is one of a number of reports that will be combined into a handbook on beryllium. Each report covers a specific topic. To-date, the following reports have been published: (1) Consolidation and Grades of Beryllium; (2) Mechanical Properties of Beryllium and the Factors Affecting these Properties; (3) Corrosion and Corrosion Protection of Beryllium; (4) Joining of Beryllium; (5) Atomic, Crystal, Elastic, Thermal, Nuclear, and other Properties of Beryllium; and (6) Beryllium Coating (Deposition) Processes and the Influence of Processing Parameters on Properties and Microstructure. The conventional method of using ingot-cast material is unsuitable for manufacturing a beryllium product. Beryllium is a highly reactive metal with a high melting point, making it susceptible to react with mold-wall materials forming beryllium compounds (BeO, etc.) that become entrapped in the solidified metal. In addition, the grain size is excessively large, being 50 to 100 {micro}m in diameter, while grain sizes of 15 {micro}m or less are required to meet acceptable strength and ductility requirements. Attempts at refining the as-cast-grain size have been unsuccessful. Because of the large grain size and limited slip systems, the casting will invariably crack during a hot-working step, which is an important step in the microstructural-refining process. The high reactivity of beryllium together with its high viscosity (even with substantial superheat) also makes it an unsuitable candidate for precision casting. In order to overcome these problems, alternative methods have been developed for the manufacturing of beryllium. The vast majority of these methods involve the use of beryllium powders. The powders are consolidated under pressure in vacuum at an elevated temperature to produce vacuum hot-pressed (VHP) blocks and vacuum hot-isostatic-pressed (HIP) forms and billets. The blocks (typically cylindrical), which are produced over a wide range of sizes (up to 183 cm dia. by 61

  5. Beryllium development programme in India

    International Nuclear Information System (INIS)

    India has fairly large deposits of beryl. The requirement of beryllium and copper-beryllium alloys in space and electronic industries has provided the incentive for the setting up of an indigenous base for the development of beryllium process metallurgy. The paper presents the developmental work carried out, in the Metallurgy Division of the Bhabha Atomic Research Centre, on the preparation of beryllium metal and its alloys starting from Indian beryl. A laboratory facility incorporating essential precautionary measures has been set up for the safe handling of beryllium and its compounds. Based on the laboratory investigations a flow-sheet suitable to Indian conditions has been developed. The flow-sheet involves preparation of anhydrous beryllium fluoride from beryl through the silico-fluoride route, magnesiothermic reduction of beryllium fluoride for the production of beryllium metal or its master alloy with copper or aluminium, and fabrication of beryllium metal. (author)

  6. Medical Surveillance for Former Workers

    Energy Technology Data Exchange (ETDEWEB)

    Tim Takaro

    2009-05-29

    The Former Hanford Worker Medical Monitoring Program, directed by the Occupational and Environmental Medicine Program at the University of Washington, served former production and other non-construction workers who were potentially exposed to workplace hazards while working for the USDOE or its contractors at Hanford. The USDOE Former Workers Program arose from Congressional action in the Defense Authorization of 1993 (Public Law 102). Section 3162 stated that, “The Secretary shall establish and carry out a program for the identification and ongoing medical evaluation of current and former Department of Energy employees who are subject to significant health risks as a result of exposure of such employees to hazardous or radioactive substances during such employment.” (This also covers former employees of USDOE contractors and subcontractors.) The key objective has been to provide these former workers with medical evaluations in order to determine whether workers have experienced significant risk due to workplace exposure to hazards. Exposures to asbestos, beryllium, and noise can produce specific medical conditions: asbestosis, berylliosis, and noise-induced hearing loss (NIHL). Each of these conditions can be identified by specific, non-invasive screening tests, which are widely available. Treatments are also available for individuals affected by these conditions. This project involved two phases. Phase I involved a needs and risk assessment, characterizing the nature and extent of workplace health hazards which may have increased the risk for long-term health effects. We categorized jobs and tasks by likelihood of exposures to specific workplace health hazards; and located and established contact with former Hanford workers. Phase II involved implementation of medical monitoring programs for former workers whose individual work history indicated significant risk for adverse health effects. We identified 118,000 former workers, employed from 1943 to 1997

  7. DNA Damage among Wood Workers Assessed with the Comet Assay

    Science.gov (United States)

    Bruschweiler, Evin Danisman; Wild, Pascal; Huynh, Cong Khanh; Savova-Bianchi, Dessislava; Danuser, Brigitta; Hopf, Nancy B.

    2016-01-01

    Exposure to wood dust, a human carcinogen, is common in wood-related industries, and millions of workers are occupationally exposed to wood dust worldwide. The comet assay is a rapid, simple, and sensitive method for determining DNA damage. The objective of this study was to investigate the DNA damage associated with occupational exposure to wood dust using the comet assay (peripheral blood samples) among nonsmoking wood workers (n = 31, furniture and construction workers) and controls (n = 19). DNA damage was greater in the group exposed to composite wood products compared to the group exposed to natural woods and controls (P < 0.001). No difference in DNA damage was observed between workers exposed to natural woods and controls (P = 0.13). Duration of exposure and current dust concentrations had no effect on DNA damage. In future studies, workers’ exposures should include cumulative dust concentrations and exposures originating from the binders used in composite wood products. PMID:27398027

  8. Final Pantex Report - 2006 [Phase 1 plan for assessment of Former Workers at the Pantex Facility

    International Nuclear Information System (INIS)

    The purpose of this project was to develop a Phase 1 plan for assessment of Former Workers at the Pantex Facility in Amarillo, TX and to determine the suitability to start a medical surveillance program among former workers for this site

  9. Risk assessment of silicosis and lung cancer among construction workers exposed to respirable quartz

    NARCIS (Netherlands)

    Tjoe Nij, E.; Heederik, D.

    2005-01-01

    Objectives: The aim of this study was to assess the magnitude of the silicosis and cancer risk among construction workers. Methods: In 1998, 1335 of 4173 invited construction workers with expected high cumulative exposure to quartz were studied for early signs of silicosis. In 2002 the study was rep

  10. Final Pantex Report - 2006 [Phase 1 plan for assessment of Former Workers at the Pantex Facility

    Energy Technology Data Exchange (ETDEWEB)

    Abdo, Ronna

    2013-07-18

    The purpose of this project was to develop a Phase 1 plan for assessment of Former Workers at the Pantex Facility in Amarillo, TX and to determine the suitability to start a medical surveillance program among former workers for this site.

  11. Assessment of PAH-exposure among coke oven workers

    Energy Technology Data Exchange (ETDEWEB)

    Vahakangas, K. [and others] [Oulu University, Oulu (Finland)

    1992-12-31

    Levels of BaP diol epoxide - DNA adducts in urine and blood were monitored for workers at the Raahe coking plant, Finland, and other relevant information was collected. All adduct values were low, but oven battery workers had slightly higher values than matched controls. Antibodies to these adducts increased somewhat after work at the plant started, no differences between smokers and non-smokers were found.

  12. Ergonomic Risk Assessment on Oil Palm Industry Workers

    OpenAIRE

    Baba Mohd DEROS; Mohd Hafiz ALI; Darliana MOHAMAD; Dian Darina Indah DARUIS

    2016-01-01

    Background: This study was an investigation conducted at two oil palm plantations in Slim River District, Perak, Malaysia on the prevalence of back pain among workers in the Malaysian oil palm industry. Many manual handling activities and tasks performed were not designed ergonomically, thus a high prevalence of musculoskeletal disorders was found among oil palm fresh fruit bunches (FFBs) manual workers. The three main objectives of this study were to determine the level of employee awareness...

  13. Inter-worker variability in lower body postures during assembly line work: implications for exposure assessment.

    Science.gov (United States)

    Keyserling, W Monroe; Wiggermann, Neal; Werner, Robert A; Gell, Nancy

    2010-05-01

    This study evaluated inter-worker variability in lower body posture and work activity during highly-structured assembly line work. Data were collected from 79 unique assembly line workstations in an engine manufacturing plant. Because the plant utilized work teams, 4-8 workers rotated through each workstation. At least 30 min of videotape was collected from at least three workers at each workstation. A computer-assisted work sampling procedure randomly selected 200 video "freeze-frames" for each worker. Lower body posture/movement (e.g., sit, stand, walk, etc.) was determined for each frame and used to estimate the percentage of time the worker spent in various postures and activities. Chi-square analyses were performed for each workstation to assess the significance of inter-worker differences. Due to variations in individual work methods, significant differences (p <.05) were found at 57 out of 79 workstations (72%). The greatest differences occurred when workers had the option to choose between standing and sitting (significant in 8 of 8 cases; in extreme examples, sit time ranged between 0-100% on one job, and 6.5-98% on another). Studying a single worker (or "proxy") can contribute to substantial error when estimating exposures in workplace studies of ergonomic stressors, since the proxy may not be representative of all workers who perform the job. Individual measurements are preferable, particularly for jobs where workers have substantial latitude to develop individualized work methods.

  14. Beryllium solubility in occupational airborne particles: Sequential extraction procedure and workplace application.

    Science.gov (United States)

    Rousset, Davy; Durand, Thibaut

    2016-01-01

    Modification of an existing sequential extraction procedure for inorganic beryllium species in the particulate matter of emissions and in working areas is described. The speciation protocol was adapted to carry out beryllium extraction in closed-face cassette sampler to take wall deposits into account. This four-step sequential extraction procedure aims to separate beryllium salts, metal, and oxides from airborne particles for individual quantification. Characterization of the beryllium species according to their solubility in air samples may provide information relative to toxicity, which is potentially related to the different beryllium chemical forms. Beryllium salts (BeF(2), BeSO(4)), metallic beryllium (Bemet), and beryllium oxide (BeO) were first individually tested, and then tested in mixtures. Cassettes were spiked with these species and recovery rates were calculated. Quantitative analyses with matched matrix were performed using inductively coupled plasma mass spectrometry (ICP-MS). Method Detection Limits (MDLs) were calculated for the four matrices used in the different extraction steps. In all cases, the MDL was below 4.2 ng/sample. This method is appropriate for assessing occupational exposure to beryllium as the lowest recommended threshold limit values are 0.01 µg.m(-3) in France([) (1) (]) and 0.05 µg.m(-3) in the USA.([ 2 ]) The protocol was then tested on samples from French factories where occupational beryllium exposure was suspected. Beryllium solubility was variable between factories and among the same workplace between different tasks. PMID:26327570

  15. Development of Biomarkers for Chronic Beryllium Disease in Mice

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, Terry

    2013-01-25

    Beryllium is a strategic metal, indispensable for national defense programs in aerospace, telecommunications, electronics, and weaponry. Exposure to beryllium is an extensively documented occupational hazard that causes irreversible, debilitating granulomatous lung disease in as much as 3 - 5% of exposed workers. Mechanistic research on beryllium exposure-disease relationships has been severely limited by a general lack of a sufficient CBD animal model. We have now developed and tested an animal model which can be used for dissecting dose-response relationships and pathogenic mechanisms and for testing new diagnostic and treatment paradigms. We have created 3 strains of transgenic mice in which the human antigen-presenting moiety, HLA-DP, was inserted into the mouse genome. Each mouse strain contains HLA-DPB1 alleles that confer different magnitude of risk for chronic beryllium disease (CBD): HLA-DPB1*0401 (odds ratio = 0.2), HLA-DPB1*0201 (odds ratio = 15), HLA-DPB1*1701 (odds ratio = 240). Our preliminary work has demonstrated that the *1701 allele, as predicted by human studies, results in the greatest degree of sensitization in a mouse ear swelling test. We have also completed dose-response experiments examining beryllium-induced lung granulomas and identified susceptible and resistant inbred strains of mice (without the human transgenes) as well as quantitative trait loci that may contain gene(s) that modify the immune response to beryllium. In this grant application, we propose to use the transgenic and normal inbred strains of mice to identify biomarkers for the progression of beryllium sensitization and CBD. To achieve this goal, we propose to compare the sensitivity and accuracy of the lymphocyte proliferation test (blood and bronchoalveolar lavage fluid) with the ELISPOT test in the three HLA-DP transgenic mice strains throughout a 6 month treatment with beryllium particles. Because of the availability of high-throughput proteomics, we will also identify

  16. Assessment of coke oven emissions exposure among coking workers

    Energy Technology Data Exchange (ETDEWEB)

    Chen, M.L.; Mao, I.F.; Wu, M.T.; Chen, J.R.; Ho, C.K.; Smith, T.J.; Wypij, D.; Christiani, D.C. [National Yang Ming University, Taipei (Taiwan). Dept. of Public Health

    1999-01-01

    Coking workers are regularly exposed to coke oven emissions, which consist primarily of polycyclic aromatic hydrocarbons and volatile organic compounds. This study measured the workers` exposure to the benzene soluble fraction of total particulates (BSF). Personal breathing-zone samples of BSF and total particulates were taken from all study subjects for 3 consecutive days. The highest BSF concentrations were found among the topside oven workers. Among the samples at the topside oven 84% exceeded the Occupational Safety and Health Administration standard (150 {mu}g/m{sup 3} BSF). The percentage of BSF in total particulates varied across job classifications, ranging from 0.3% in wharf men to 24% in tar chasers. Area sampling indicated that the BSF concentration at the topside area was sixty fold higher than that at the administrative area, which was approximately 2 km from the coke oven plant.

  17. Reprocessing technology development for irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, H.; Sakamoto, N. [Oarai Research Establishment, Ibaraki-ken (Japan); Tatenuma, K. [KAKEN Co., Ibaraki-ken (Japan)] [and others

    1995-09-01

    At present, beryllium is under consideration as a main candidate material for neutron multiplier and plasma facing material in a fusion reactor. Therefore, it is necessary to develop the beryllium reprocessing technology for effective resource use. And, we have proposed reprocessing technology development on irradiated beryllium used in a fusion reactor. The preliminary reprocessing tests were performed using un-irradiated and irradiated beryllium. At first, we performed beryllium separation tests using un-irradiated beryllium specimens. Un-irradiated beryllium with beryllium oxide which is a main impurity and some other impurities were heat-treated under chlorine gas flow diluted with Ar gas. As the results high purity beryllium chloride was obtained in high yield. And it appeared that beryllium oxide and some other impurities were removed as the unreactive matter, and the other chloride impurities were separated by the difference of sublimation temperature on beryllium chloride. Next, we performed some kinds of beryllium purification tests from beryllium chloride. And, metallic beryllium could be recovered from beryllium chloride by the reduction with dry process. In addition, as the results of separation and purification tests using irradiated beryllium specimens, it appeared that separation efficiency of Co-60 from beryllium was above 96%. It is considered that about 4% Co-60 was carried from irradiated beryllium specimen in the form of cobalt chloride. And removal efficiency of tritium from irradiated beryllium was above 95%.

  18. Status of beryllium development for fusion applications

    Energy Technology Data Exchange (ETDEWEB)

    Billone, M.C. [Argonne National Lab., IL (United States); Donne, M.D. [Kernforschungszentrum Karlsruhe GmbH (Germany). Institut fuer Neutronphysik and Reaktortechnik; Macaulay-Newcombe, R.G. [McMaster Univ., Ontario, CA (United States). Dept. of Engineering Physics

    1994-05-01

    Beryllium is a leading candidate material for the neutron multiplier of tritium breeding blankets and the plasma facing component of first wall and divertor systems. Depending on the application, the fabrication methods proposed include hot-pressing, hot-isostatic-pressing, cold isostatic pressing/sintering, rotary electrode processing and plasma spraying. Product forms include blocks, tubes, pebbles, tiles and coatings. While, in general, beryllium is not a leading structural material candidate, its mechanical performance, as well its performance with regard to sputtering, heat transport, tritium retention/release, helium-induced swelling and chemical compatibility, is an important consideration in first-wall/blanket design. Differential expansion within the beryllium causes internal stresses which may result in cracking, thereby affecting the heat transport and barrier performance of the material. Overall deformation can result in loading of neighboring structural material. Thus, in assessing the performance of beryllium for fusion applications, it is important to have a good database in all of these performance areas, as well as a set of properties correlations and models for the purpose of interpolation/extrapolation.

  19. Radiological assessment of worker doses during sludge mobilization and removal at the Melton Valley storage tanks

    Energy Technology Data Exchange (ETDEWEB)

    Kerr, G.D.; Coleman, R.L.; Kocher, D.C.; Wynn, C.C.

    1996-12-17

    This report presents an assessment of potential radiation doses to workers during mobilization and removal of contaminated sludges from the Melton Valley Storage Tanks at Oak Ridge National Laboratory. The assessment is based on (1) measurements of radionuclide concentrations in sludge and supernatant liquid samples from the waste storage tanks, (2) measurements of gamma radiation levels in various areas that will be accessed by workers during normal activities, (3) calculations of gamma radiation levels for particular exposure situations, especially when the available measurements are not applicable, and (4) assumed scenarios for worker activities in radiation areas. Only doses from external exposure are estimated in this assessment. Doses from internal exposure are assumed to be controlled by containment of radioactive materials or respiratory protection of workers and are not estimated.

  20. Beryllium. Its minerals. Pt. 1

    International Nuclear Information System (INIS)

    With this work a series of reports begins, under the generic name 'Beryllium', related to several aspects of beryllium technology. The target is to update, with critical sense, current bibliographic material in order to be used in further applications. Some of the most important beryllium ores, the Argentine emplacement of their deposits and world occurrence are described. Argentine and world production, resources and reserves are indicated here as well. (Author)

  1. Derivation of beryllium guidelines for use in establishing cleanup levels at the Peek Street and Sacandaga sites, New York

    International Nuclear Information System (INIS)

    Guideline levels are derived for beryllium in soil and on indoor surfaces at the Peek Street and Sacandaga sites in the state of New York. On the basis of highly conservative assumptions, the soil beryllium concentration that corresponds to a 10-4 carcinogenic risk level is estimated to be 13 mg/kg at both sites. Calculations indicate that the proposed US Department of Energy guideline of 2 μg/ft2 for beryllium in dust on indoor surfaces would be sufficiently protective of human health. For occupational protection of workers during cleanup operations, Office of Safety and Health Administration standards for beryllium are referenced and restated

  2. Joining of Beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, A

    2006-02-01

    A handbook dealing with the many aspects of beryllium that would be important for the users of this metal is currently being prepared. With an introduction on the applications, advantages and limitations in the use of this metal the following topics will be discussed in this handbook: physical, thermal, and nuclear properties; extraction from the ores; purification and casting of ingots; production and types of beryllium powders; consolidation methods, grades, and properties; mechanical properties with emphasis on the various factors affecting these properties; forming and mechanical working; welding, brazing, bonding, and fastening; machining; powder deposition; corrosion; health aspects; and examples of production of components. This report consists of ''Section X--Joining'' from the handbook. The prefix X is maintained here for the figures, tables and references. In this section the different methods used for joining beryllium and the advantages, disadvantages and limitations of each are presented. The methods discussed are fusion welding, brazing, solid state bonding (diffusion bonding and deformation bonding), soldering, and mechanical fastening. Since beryllium has a high affinity for oxygen and nitrogen with the formation of oxides and nitrides, considerable care must be taken on heating the metal, to protect it from the ambient atmosphere. In addition, mating surfaces must be cleaned and joints must be designed to minimize residual stresses as well as locations for stress concentration (notch effects). In joining any two metals the danger exists of having galvanic corrosion if the part is subjected to moisture or to any type of corroding environment. This becomes a problem if the less noble (anodic) metal has a significantly smaller area than the more noble (cathodic) metal since the ions (positive charges) from the anodic (corroding) metal must correspond to the number of electrons (negative charges) involved at the cathode. Beryllium

  3. Status of beryllium development for fusion applications

    International Nuclear Information System (INIS)

    Beryllium is a leading candidate material for the neutron multiplier of tritium breeding blankets and the plasma-facing component of first-wall and divertor systems. Depending on the application, the fabrication methods proposed include hot-pressing, hot-isostatic-pressing, cold-isostatic-pressing/sintering, rotary electrode processing and plasma spraying. Product forms include blocks, tubes, pebbles, tiles and coatings. While, in general, beryllium is not a leading structural material candidate, its mechanical performance, as well as its performance with regard to sputtering, heat transport, tritium retention/release, helium-induced swelling and chemical compatibility, is an important consideration in first-wall/blanket design. Differential expansion within the beryllium causes internal stresses which may result in cracking, thereby affecting the heat transport and barrier performance of the material. Overall deformation can result in loading of neighboring structural material. Thus, in assessing the performance of beryllium for fusion applications, it is important to have a good database in all of these performance areas, as well as a set of properties correlations and models for the purpose of interpolation/extrapolation.In this current work, the range of anticipated fusion operating conditions is reviewed. The thermal, mechanical, chemical compatibility, tritium retention/release, and helium retention/swelling databases are then reviewed for fabrication methods and fusion operating conditions of interest. Properties correlations and uncertainty ranges are also discussed. In the case of the more complex phenomena of tritium retention/release and helium-induced swelling, fundamental mechanisms and models are reviewed in more detail. Areas in which additional data are needed are highlighted, along with some trends which suggest ways of optimizing the performance of beryllium for fusion applications. (orig.)

  4. Assessing Quality of Working Life Among Malaysian Workers.

    Science.gov (United States)

    Sulaiman, Nur Suffia; Choo, Wan Yuen; Mat Yassim, Abdul Rahim; Van Laar, Darren; Chinna, Karuthan; Majid, Hazreen Abdul

    2015-11-01

    The Work-Related Quality of Life Scale-2 (WRQLS-2) has been used to measure quality of working life (QOWL) in the United Kingdom. In this study, the scale was translated and normalized into Malay. The scale was translated using the back-translation method, pretesting, and pilot testing. It was conducted among health care and office workers. It was tested in 3 stages; confirmatory factor analysis at stages 1 and 3 and exploratory factor analysis at stage 2. The Malaysian WRQLS-2 had 5 factors: "General Well-Being," "Job and Career Satisfaction," "Employee Engagement," "Home-Work Interface," and "Stress at Work." The scale showed good convergent and construct validity and also reliability. Perception of good QOWL may differ because of cultural influences and varying work environments. The validated Malaysian WRQLS-2 can be used to determine the QOWL of Malaysian office and health care workers.

  5. Beryllium. Beryllium oxide, obtention and properties. Pt.4

    International Nuclear Information System (INIS)

    As a continuation of the 'Beryllium' series this work reviews several methods of high purity beryllia production. Diverse methods of obtention and purification from different beryllium compounds are described. Some chemical, mechanical and electrical properties related with beryllia obtention methods are summarized. (Author)

  6. The results of medical surveillance of beryllium production personnel

    International Nuclear Information System (INIS)

    The report presents results of surveillance of 1836 workers of beryllium production of Ulba Metallurgical Plant JSC with the acute and chronic forms of occupation diseases for 52 years of its operation. The dependence of acute and chronic occupation lesions on the protection degree is shown. It has been found out that, the risk of getting an occupation disease increases sharply at the moments of experimental works and at the time of reconstruction and some other extreme conditions in the production, that is supported by fixed lesions of eye mucous coat, skin and lung lesions. In this case, the readiness of people for their work in deleterious conditions and their personal responsibility for following the regulations of safety occupational standards plays a definite role. Therefore, the issues of protection are of paramount importance in prophylaxis both of acute and chronic exposure to beryllium. An influence of duration of service and occupation on chronic beryllium diseases is shown. A parallel between the lung beryllium disease and skin lesions by insoluble beryllium compounds is drawn for the first time. (author)

  7. Fallout beryllium-7 as a soil and sediment tracer in river basins: current status and needs

    Science.gov (United States)

    Taylor, Alex; Blake, Will H.; Smith, Hugh G.; Mabit, Lionel; Keith-Roach, Miranda J.

    2013-04-01

    Beryllium-7 is a cosmogenic radionuclide formed in the upper atmosphere by cosmic ray spallation of nitrogen and oxygen. Its constant natural production and fallout via precipitation coupled with its ability to bind to soil particles have underpinned its application as a sediment tracer. The short half-life of beryllium-7 (53.3 days) lends itself to tracing sediment dynamics over short time periods, thus, enabling assessment of the effect of land use change upon soil redistribution. Although beryllium-7 has been widely applied as a tracer to date, there remain crucial gaps in understanding relating to the assumptions for its use. To further support the application of beryllium-7 as a tracer across a range of environments requires consideration of both the current strengths and shortcomings of the technique to direct research needs. Here we review research surrounding the assumptions underpinning beryllium-7 use as a tracer and identify key knowledge gaps relating to i) the effects of rain shadowing and vegetation interception upon beryllium-7 fallout uniformity at the hillslope-scale; ii) the effect of preferential flow pathways upon beryllium-7 depth distribution in soil and overland flow upon beryllium-7 inventory uniformity and iii) the potential for beryllium-7 desorption in saline and reducing environments. To provide continued support for the use of beryllium-7 as a hillslope and catchment-scale tracer, there is an urgent need to undertake further research to quantify the effect of these factors upon tracer estimates.

  8. Explanation of test and assessment of chromosomal aberrations on occupational health examinations for radiation workers

    International Nuclear Information System (INIS)

    Test and Assessment of Chromosomal Aberrations on Occupational Health Examinations for Radiation Workers was formulated for standardizing analysis and outcome assessment of chromosomal aberrations on occupational health examinations for radiation workers. In order to provide experimental and theoretical basis for implementation and extension of this standard, this paper interpreted the standard comprehensively, including some existed problems that methods on detection and outcome assessment of chromosomal aberrations is not unified in different laboratories in China, and related criteria,laws and regulations at home and abroad are not fit for the detection of chromosomal aberrations for radiation workers very well; some introduction on methods of chromosomal slide preparation, discriminant analysis and outcome assessment of chromosomal aberration; and some influencing factors in the quality of chromosomal aberration detection. (authors)

  9. Workers' radioprotection: professional exposure to ionizing radiation in France: assessment for 2010

    International Nuclear Information System (INIS)

    As more than 300.000 workers are potentially exposed to different artificial sources of ionizing radiation in different activity sectors in France (nuclear, industry, research, and medicine) and some others to natural radiation sources, this report proposes an assessment of these exposures for 2010. The report describes the monitoring of professional exposure (legal framework, monitoring modalities, means and actions of the IRSN), presents the methodology adopted for this annual assessment of workers' exposure to ionizing radiation. It gives this assessment for civilian activities submitted to an authorization or declaration regime and for defence activities (general results for external and internal exposures, exposure in the medical and veterinary sector, in the nuclear sector, in the industrial sector, in the research sector). It finally addresses the exposure of workers to natural radioactivity

  10. Service quality assessment of workers compensation health care delivery programs in New York using SERVQUAL.

    Science.gov (United States)

    Arunasalam, Mark; Paulson, Albert; Wallace, William

    2003-01-01

    Preferred provider organizations (PPOs) provide healthcare services to an expanding proportion of the U.S. population. This paper presents a programmatic assessment of service quality in the workers' compensation environment using two different models: the PPO program model and the fee-for-service (FFS) payor model. The methodology used here will augment currently available research in workers' compensation, which has been lacking in measuring service quality determinants and assessing programmatic success/failure of managed care type programs. Results indicated that the SERVQUAL tool provided a reliable and valid clinical quality assessment tool that ascertained that PPO marketers should focus on promoting physician outreach (to show empathy) and accessibility (to show reliability) for injured workers.

  11. Service quality assessment of workers compensation health care delivery programs in New York using SERVQUAL.

    Science.gov (United States)

    Arunasalam, Mark; Paulson, Albert; Wallace, William

    2003-01-01

    Preferred provider organizations (PPOs) provide healthcare services to an expanding proportion of the U.S. population. This paper presents a programmatic assessment of service quality in the workers' compensation environment using two different models: the PPO program model and the fee-for-service (FFS) payor model. The methodology used here will augment currently available research in workers' compensation, which has been lacking in measuring service quality determinants and assessing programmatic success/failure of managed care type programs. Results indicated that the SERVQUAL tool provided a reliable and valid clinical quality assessment tool that ascertained that PPO marketers should focus on promoting physician outreach (to show empathy) and accessibility (to show reliability) for injured workers. PMID:15271631

  12. The beryllium quandary: will the lower exposure limits spur new developments in sampling and analysis?

    Energy Technology Data Exchange (ETDEWEB)

    Brisson, Michael

    2013-06-03

    At the time this article was written, new rulemakings were under consideration at OSHA and the U.S. Department of Energy (DOE) that would propose changes to occupational exposure limits for beryllium. Given these developments, it’s a good time to review the tools and methods available to IHs for assessing beryllium air and surface contamination in the workplace—what’s new and different, and what’s tried and true. The article discusses limit values and action levels for beryllium, problematic aspects of beryllium air sampling, sample preparation, sample analysis, and data evaluation.

  13. Impurities effect on the swelling of neutron irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Donne, M.D.; Scaffidi-Argentina, F. [Institut fuer Neutronenphysik und Reaktortechnik, Karlsruhe (Germany)

    1995-09-01

    An important factor controlling the swelling behaviour of fast neutron irradiated beryllium is the impurity content which can strongly affect both the surface tension and the creep strength of this material. Being the volume swelling of the old beryllium (early sixties) systematically higher than that of the more modem one (end of the seventies), a sensitivity analysis with the aid of the computer code ANFIBE (ANalysis of Fusion Irradiated BEryllium) to investigate the effect of these material properties on the swelling behaviour of neutron irradiated beryllium has been performed. Two sets of experimental data have been selected: the first one named Western refers to quite recently produced Western beryllium, whilst the second one, named Russian refers to relatively old (early sixties) Russian beryllium containing a higher impurity rate than the Western one. The results obtained with the ANFIBE Code were assessed by comparison with experimental data and the used material properties were compared with the data available in the literature. Good agreement between calculated and measured values has been found.

  14. Thermal fatigue of beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Deksnis, E.; Ciric, D.; Falter, H. [JET Joint undertaking, Abingdon (United Kingdom)] [and others

    1995-09-01

    Thermal fatigue life of S65c beryllium castellated to a geometry 6 x 6 x (8-10)mm deep has been tested for steady heat fluxes of 3 MW/m{sup 2} to 5 MW/m{sup 2} and under pulsed heat fluxes (10-20 MW/m{sup 2}) for which the time averaged heat flux is 5 MW/m{sup 2}. These tests were carried out in the JET neutral beam test facility A test sequence with peak surface temperatures {le} 600{degrees}C produced no visible fatigue cracks. In the second series of tests, with T{sub max} {le} 750{degrees}C evidence for fatigue appeared after a minimum of 1350 stress cycles. These fatigue data are discussed in view of the observed lack of thermal fatigue in JET plasma operations with beryllium PFC. JET experience with S65b and S65c is reviewed; recent operations with {Phi} = 25 MW/m{sup 2} and sustained melting/resolidification are also presented. The need for a failure criterion for finite element analyses of Be PFC lifetimes is discussed.

  15. Assessment physical load of dockers in a worker cooperative

    Directory of Open Access Journals (Sweden)

    Hernán D. Zapata

    2011-05-01

    Full Text Available Manual labourers are workers whose job consists of humping goods. Task commonly related to a varied level of mechanical stress due both to its mechanical stress demand and the workplace risk factors. Objectives: to determine the level of exposure to physical workload amongst a sample of manual labourers who work at the factory of food concentrate for animal. To propose general administrative control and working atmosphere measures. Methodology: a study of descriptive observational type by convenience was carried out. The sample consisted of 41 manual labourers who were administered a socio-demographic survey in order to know the population characteristics. To those fulfilling the inclusion criteria, a heart rate monitoring was used. Afterwards, the Frimat method was administered to determine the levels of exposure to physical work load according to workload rates. Statistical analysis favoured was descriptive and non-parametric (Chisquare χ Results: two out of the four work sites under study constitute the most representative workload to personnel. While the study, the three labourers (100% shoving and 14 (63.6% out of the 22 labourers loading goods up and down ranged from hard to extremely tough levels of workload. Conversely, 11(91.7% labourers carrying raw material and 4 (100% sewing sacks were placed under a low level ranging between a minimal and bearable workload. Discussion: the kinds of job as well as the activities related to it affect the level of physical workload. Personal factors can have an influence upon physical workload.

  16. Assessment of functional integrity of liver among workers exposed to soluble nickel compounds during nickel plating

    Directory of Open Access Journals (Sweden)

    Kalahasthi Ravi Babu

    2006-01-01

    Full Text Available The present study investigates the functional integrity of liver among workers exposed to nickel during nickel-plating process. The functional integrity of liver was assessed in 69 workers who are exposed to nickel during nickel plating and considered as nickel-exposed workers; and 50 administrative workers residing in same city, but away from the place of work of study group, were considered as control group. The level of urine nickel was measured by using a flameless atomic absorption spectrophotometer. Using kits supplied by Bayer Diagnostics, we determined serum markers of liver function tests. Results: The levels of urine nickel were significantly increased in high-and moderate-exposure groups as compared to control group. The levels of serum transaminases -viz, alanine transaminase and aspartate transaminase-were significantly increased in nickel-exposed workers, who had high urine nickel levels as compared to control group. The level of serum albumin was negatively correlated with urine nickel levels. The levels of serum transaminases and serum g- glutamyl- transpeptidase were positively and significantly correlated with urine nickel levels. Conclusion: Results indicate that workers who had high urine nickel levels had a consistent effect on hepatic inflammatory function.

  17. Beryllium usage in fusion blankets and beryllium data needs

    International Nuclear Information System (INIS)

    Increasing numbers of designers are choosing beryllium for fusion reactor blankets because it, among all nonfissile materials, produces the highest number (2.5 neutron in an infinite media) of neutrons per 14-MeV incident neutron. In amounts of about 20 cm of equivalent solid density, it can be used to produce fissile material, to breed all the tritium consumed in ITER from outboard blankets only, and in designs to produce Co-60. The problem is that predictions of neutron multiplication in beryllium are off by some 10 to 20% and appear to be on the high side, which means that better multiplication measurements and numerical methods are needed. The n,2n reactions result in two helium atoms, which cause radiation damage in the form of hardening at low temperatures (300/degree/C). The usual way beryllium parts are made is by hot pressing the powder. A lower cost method is to cold press and then sinter. There is no radiation damage data on this form of beryllium. The issues of corrosion, safety relative to the release of the tritium built-up inside beryllium, and recycle of used beryllium are also discussed. 10 figs

  18. Real-time assessment of exposure dose to workers in radiological environments during decommissioning of nuclear facilities

    International Nuclear Information System (INIS)

    Highlights: • The method of exposure dose assessment to workers during decommissioning of nuclear facilities. • The environments of simulation were designed under a virtual reality. • To assess exposure dose to workers, human model was developed within a virtual reality. - Abstract: This objective of this paper is to develop a method to simulate and assess the exposure dose to workers during decommissioning of nuclear facilities. To simulate several scenarios, decommissioning environments were designed using virtual reality. To assess exposure dose to workers, a human model was also developed using virtual reality. The exposure dose was measured and assessed under the principle of ALARA in accordance with radiological environmental change. This method will make it possible to plan for the exposure dose to workers during decommissioning of nuclear facilities

  19. Beryllium technology workshop, Clearwater Beach, Florida, November 20, 1991

    International Nuclear Information System (INIS)

    This report discusses the following topics: beryllium in the ITER blanket; mechanical testing of irradiated beryllium; tritium release measurements on irradiated beryllium; beryllium needs for plasma-facing components; thermal conductivity of plasma sprayed beryllium; beryllium research at the INEL; Japanese beryllium research activities for in-pile mockup tests on ITER; a study of beryllium bonding of copper alloy; new production technologies; thermophysical properties of a new ingot metallurgy beryllium product line; implications of beryllium:steam interactions in fusion reactors; and a test program for irradiation embrittlement of beryllium at JET

  20. New and Emerging Technologies for Real-Time Air and Surface Beryllium Monitoring; FINAL

    International Nuclear Information System (INIS)

    In this study, five emerging technologies were identified for real-time monitoring of airborne beryllium: Microwave-Induced Plasma Spectroscopy (MIPS), Aerosol Beam-Focused Laser-Induced Plasma Spectroscopy (ABFLIPS), Laser-Induced Breakdown Spectroscopy (LIBS), Surfaced-Enhanced Raman Scattering (SERS) Spectroscopy, and Micro-Calorimetric Spectroscopy (CalSpec). Desired features of real-time air beryllium monitoring instrumentation were developed from the Y-12 CBDPP. These features were used as guidelines for the identification of potential technologies as well as their unique demonstrated capability to provide real-time monitoring of similar materials. However, best available technologies were considered, regardless of their ability to comply with the desired features. None of the five technologies have the capability to measure the particle size of airborne beryllium. Although reducing the total concentration of airborne beryllium is important, current literature suggests that reducing or eliminating the concentration of respirable beryllium is critical for worker health protection. Eight emerging technologies were identified for surface monitoring of beryllium. CalSpec, MIPS, SERS, LIBS, Laser Ablation, Absorptive Stripping Voltametry (ASV), Modified Inductively Coupled Plasma (ICP) Spectroscopy, and Gamma BeAST. Desired features of real-time surface beryllium monitoring were developed from the Y-12 CBDPP. These features were used as guidelines for the identification of potential technologies. However, the best available technologies were considered regardless of their ability to comply with the desired features

  1. New and Emerging Technologies for Real-Time Air and Surface Beryllium Monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Phifer, B.E. Jr.; Churnetski, E.L.; Cooke, L.E.; Reed, J.J.; Howell, M.L.; Smith, V.D.

    2001-09-01

    In this study, five emerging technologies were identified for real-time monitoring of airborne beryllium: Microwave-Induced Plasma Spectroscopy (MIPS), Aerosol Beam-Focused Laser-Induced Plasma Spectroscopy (ABFLIPS), Laser-Induced Breakdown Spectroscopy (LIBS), Surfaced-Enhanced Raman Scattering (SERS) Spectroscopy, and Micro-Calorimetric Spectroscopy (CalSpec). Desired features of real-time air beryllium monitoring instrumentation were developed from the Y-12 CBDPP. These features were used as guidelines for the identification of potential technologies as well as their unique demonstrated capability to provide real-time monitoring of similar materials. However, best available technologies were considered, regardless of their ability to comply with the desired features. None of the five technologies have the capability to measure the particle size of airborne beryllium. Although reducing the total concentration of airborne beryllium is important, current literature suggests that reducing or eliminating the concentration of respirable beryllium is critical for worker health protection. Eight emerging technologies were identified for surface monitoring of beryllium. CalSpec, MIPS, SERS, LIBS, Laser Ablation, Absorptive Stripping Voltametry (ASV), Modified Inductively Coupled Plasma (ICP) Spectroscopy, and Gamma BeAST. Desired features of real-time surface beryllium monitoring were developed from the Y-12 CBDPP. These features were used as guidelines for the identification of potential technologies. However, the best available technologies were considered regardless of their ability to comply with the desired features.

  2. How occupational health is assessed in mine workers in Murmansk Oblast

    Directory of Open Access Journals (Sweden)

    Tormod Brenn

    2012-05-01

    Full Text Available Objectives. We aimed to describe how work exposure and occupational health is assessed for mine workers in Murmansk Oblast, Russia. Study design. A descriptive study based on current practice, laws and available literature. Methods. The information and data were obtained from scientific publications, reports, regional and federal statistics, legal documents, through personal visits and onsite inspections. Results. Several institutions are involved in these assessments, but all mine workers have been examined by specialists at one institution, which helps to ensure that the work is of stable quality and adds reliability value to the numbers. Workplace risks are assigned hazard grades, which influence the frequency of periodic medical examinations and salary levels. The examinations are aimed to diagnose latent or manifest occupational disease. This may lead to relocation to a workplace with lower exposure levels, free medical treatment, compensation and a lower pension age. Conclusions. Regulations and systems to protect the health of mine workers have more emphasis on control and repair than on prevention. Since relocation can lower the salary, some workers may under-report medical problems. To what degree this happens is unknown. The mining enterprises pay the medical service provider for periodic medical examinations, which could potentially weaken their independent role. This framework is important to understand when studying and assessing the health of working populations in the circumpolar region.

  3. Worker exposures to triclopyr: risk assessment through measurements in urine samples.

    Science.gov (United States)

    Gosselin, Nathalie H; Brunet, Robert C; Carrier, Gaétan; Dosso, Amssétou

    2005-07-01

    In the province of Quebec (Canada), the phytocide Garlon 4, whose active ingredient is triclopyr, is often used to prevent trees from reaching electrical conductors. The object of this paper is to assess the potential health risks in workers coming into contact with Garlon 4. Ten workers collected their urine during the 22 h following the beginning of a work shift. Measured urinary amounts of triclopyr varied between 1 and 13 mg. The absorbed daily doses were estimated from the amounts of triclopyr in urine through the use of a kinetic model that links the rates of triclopyr elimination to absorbed doses. These estimated doses were compared with the no-observed-effect level (NOEL) observed in rats: 5 mg per kg of body weight. The upper-bound estimations of the worker's daily absorbed doses were found to be 13.3% or less of the rat NOEL. PMID:15703284

  4. Assessment of eye lens doses for workers during interventional radiology procedures

    International Nuclear Information System (INIS)

    The assessment of eye lens doses for workers during interventional radiology (IR) procedures was performed using a new eye lens dosemeter. In parallel, the results of routine individual monitoring were analysed and compared with the results obtained from measurements with a new eye lens dosemeter. The eye lens doses were assessed using Hp(3) measured at the level of the eyes and were compared with Hp(10) measured with the whole-body dosemeter above the lead collar. The information about use of protective measures, the number of performed interventional procedures per month and their fluoroscopy time was also collected. The assessment of doses to the lens of the eye was done for 50 IR workers at 9 Lithuanian hospitals for the period of 2012-2013. If the use of lead glasses is not taken into account, the estimated maximum annual dose equivalent to the lens of the eye was 82 mSv. (authors)

  5. Assessing Assessment – the Danish Experience of Worker Participation in Risk Assessment

    DEFF Research Database (Denmark)

    Jensen, Per Langå

    2002-01-01

    The transposition of the EU Framework Directive resulted in new Danish legislation on workplace assessment whereby a mandatory participatory process to handle work environment is to be established in all firms. The first studies on the implementations shows that while smaller firms do not comply......; the larger firms appreciate the new requirements. But a closer analysis shows that the ambitions behind the law are still not fulfilled. By analysing the results through the optics of different theories this paper addresses what strategies to follow to develop the activities and thereby develop...... the participatory program established in the Danish law on work environment...

  6. Assessment of potential damage to DNA in urine of coke oven workers: an assay of unscheduled DNA synthesis.

    OpenAIRE

    Roos, F.; Renier, A.; Ettlinger, J; Iwatsubo, Y; Letourneux, M; Haguenoer, J M; Jaurand, M C; Pairon, J C

    1997-01-01

    OBJECTIVES: A study was conducted in coke oven workers to evaluate the biological consequences of the exposure of these workers, particularly production of potential genotoxic factors. METHODS: 60 coke oven workers and 40 controls were recruited in the same iron and steel works. Exposure to polycyclic aromatic hydrocarbons (PAHs) was assessed by job and measurement of 1-hydroxypyrene (1OHP) in urine samples. An unscheduled DNA synthesis assay was performed on rat pleural mesothelial cells use...

  7. Chemometrics models for assessment of oxidative stress risk in chrome-electroplating workers.

    Science.gov (United States)

    Zendehdel, Rezvan; Shetab-Boushehri, Seyed Vahid; Azari, Mansoor R; Hosseini, Vajihe; Mohammadi, Hamidreza

    2015-04-01

    Oxidative stress is the main cause of hexavalant chromium-induced damage in chrome electroplating workers. The main goal of this study is toxicity analysis and the possibility of toxicity risk categorizing in the chrome electroplating workers based on oxidative stress parameters as prognostic variables. We assessed blood chromium levels and biomarkers of oxidative stress such as lipid peroxidation, thiol (SH) groups and antioxidant capacity of plasma. Data were subjected to principle component analysis (PCA) and artificial neuronal network (ANN) to obtain oxidative stress pattern for chrome electroplating workers. Blood chromium levels increased from 4.42 ppb to 10.6 ppb. Induction of oxidative stress was observed by increased in lipid peroxidation (22.38 ± 10.47 μM versus 14.74 ± 4.82 μM, p < 0.0008), decreased plasma antioxidant capacity (3.17 ± 1.35 μM versus 7.74 ± 4.45 μM, p < 0.0001) and plasma total thiol (SH groups) (0.21 ± 0.07 μM versus 0.45 ± 0.41 μM, p < 0.0042) in comparison to controls. Based on the oxidative parameters, two groups were identified by PCA methods. One category is workers with the risk of oxidative stress and second group is subjects with probable risk of oxidative stress induction. ANN methods can predict oxidative-risk category for assessment of toxicity induction in chrome electroplaters. The result showed multivariate modeling can be interpreted as the induced biochemical toxicity in the workers exposed to hexavalent chromium. Different occupation groups were assessed on the basis of risk level of oxidative stress which could further justify proceeding engineering control measures.

  8. Release of beryllium from mineral ores in artificial lung and skin surface fluids.

    Science.gov (United States)

    Duling, Matthew G; Stefaniak, Aleksandr B; Lawrence, Robert B; Chipera, Steve J; Virji, M Abbas

    2012-06-01

    Exposure to some manufactured beryllium compounds via skin contact or inhalation can cause sensitization. A portion of sensitized persons who inhale beryllium may develop chronic beryllium disease (CBD). Little is understood about exposures to naturally occurring beryllium minerals. The purpose of this study was to assess the bioaccessibility of beryllium from bertrandite ore. Dissolution of bertrandite from two mine pits (Monitor and Blue Chalk) was evaluated for both the dermal and inhalation exposure pathways by determining bioaccessibility in artificial sweat (pH 5.3 and pH 6.5), airway lining fluid (SUF, pH 7.3), and alveolar macrophage phagolysosomal fluid (PSF, pH 4.5). Significantly more beryllium was released from Monitor pit ore than Blue Chalk pit ore in artificial sweat buffered to pH 5.3 (0.88 ± 0.01% vs. 0.36 ± 0.00%) and pH 6.5 (0.09 ± 0.00% vs. 0.03 ± 0.01%). Rates of beryllium released from the ores in artificial sweat were faster than previously measured for manufactured forms of beryllium (e.g., beryllium oxide), known to induce sensitization in mice. In SUF, levels of beryllium were below the analytical limit of detection. In PSF, beryllium dissolution was biphasic (initial rapid diffusion followed by latter slower surface reactions). During the latter phase, dissolution half-times were 1,400 to 2,000 days, and rate constants were ~7 × 10(-10) g/(cm(2)·day), indicating that bertrandite is persistent in the lung. These data indicate that it is prudent to control skin and inhalation exposures to bertrandite dusts. PMID:21866318

  9. Exposure assessment of workers in printed electronics workplace.

    Science.gov (United States)

    Lee, Ji Hyun; Sohn, Eun Kyung; Ahn, Jin Soo; Ahn, Kangho; Kim, Keun Soo; Lee, Jong Hwan; Lee, Taik Min; Yu, Il Je

    2013-07-01

    Printed electronics uses converging technologies, such as printing, fine mechanics, nanotechnology, electronics and other new technologies. Consequently, printed electronics raises additional health and safety concerns to those experienced in the traditional printing industry. This study investigated two printed electronics workplaces based on a walk-through survey and personal and area sampling. All the printed electronics operations were conducted in a cleanroom. No indication of exposure to excess silver nanoparticles or carbon nanotubes (CNTs) was found. While the organic solvents were lower than current occupational exposure limits, there was a lack of engineering controls, such as local exhaust ventilation, correct enclosure and duct connections. There was also an insufficient quantity of personal protective equipment, and some organic solvents not described in the safety data sheets (SDSs) were detected in the air samples. Plus, the cleaning work, a major emissions operation, was not conducted within a hood, and the cleaning waste was not properly disposed of. Therefore, the present exposure assessment results from two printed electronics workplaces suggest that the printed electronics industry needs to take note of the occupational safety and health risks and hazards already established by the traditional printing industry, along with new risks and hazards originating from converging technologies such as nanotechnology.

  10. Hanford Site Beryllium Program: Past, Present, and Future - 12428

    International Nuclear Information System (INIS)

    The U.S. Department of Energy (DOE) has a long history of beryllium use because of the element's broad application to many nuclear operations and processes. At the Hanford Site beryllium alloy was used to fabricate parts for reactors, including fuel rods for the N-Reactor during plutonium production. Because of continued confirmed cases of chronic beryllium disease (CBD), and data suggesting CBD occurs at exposures to low-level concentrations, the DOE decided to issue a rule to further protect federal and contractor workers from hazards associated with exposure to beryllium. When the beryllium rule was issued in 1999, each of the Hanford Site contractors developed a Chronic Beryllium Disease Prevention Program (CBDPP) and initial site wide beryllium inventories. A new site-wide CBDPP, applicable to all Hanford contractors, was issued in May, 2009. In the spring of 2010 the DOE Headquarters Office of Health, Safety, and Security (HSS) conducted an independent inspection to evaluate the status of implementation of the Hanford Site Chronic Beryllium Disease Prevention Program (CBDPP). The report identified four Findings and 12 cross-cutting Opportunities for Improvement (OFIs). A corrective action plan (CAP) was developed to address the Findings and crosscutting OFIs. The DOE directed affected site contractors to identify dedicated resources to participate in development of the CAP, along with involving stakeholders. The CAP included general and contractor-specific recommendations. Following initiation of actions to implement the approved CAP, it became apparent that additional definition of product deliverables was necessary to assure that expectations were adequately addressed and CAP actions could be closed. Consequently, a supplement to the original CAP was prepared and transmitted to DOE-HQ for approval. Development of the supplemental CAP was an eight month effort. From the onset a core group of CAP development members were identified to develop a mechanism for

  11. Assessment of hand hygiene compliance after hand hygiene education among health care workers in Cambodia.

    Science.gov (United States)

    Sansam, Sim; Yamamoto, Eiko; Srun, Sok; Sinath, Yin; Moniborin, Mey; Bun Sim, Kheang; Reyer, Joshua A; Yoshida, Yoshitoku; Hamajima, Nobuyuki

    2016-05-01

    Health care-associated infection (HCAI) is the most frequent adverse event for hospitalized patients. Hand hygiene is a simple and effective solution to protect patients from HCAI. This study aimed to introduce hand hygiene to health care workers based on the World Health Organization guideline for reducing HCAI in Cambodia and to assess their behavioral patterns on hand hygiene. All health care workers at Kampong Cham provincial hospital had lectures and practice on hand hygiene in January 2012. The surveys for hand hygiene compliance (HHC) were performed after 6 months, 1 year and 2 years, respectively. The number of surgical site infections (SSI) was counted in 2011 and 2014. Our analysis used the data of 58 workers, who were observed at all three points, although 139 workers were observed during the study period. The average of HHC at 6 months, 1 year and 2 years were 62.37%, 85.76% and 80.36%, respectively. The improved group (HHC 2 years/1 year≧1) had 32 workers, whereas the worsened group (HHC 2 years/1 yearsex, age or occupations. The improved group had more workers of General (31.2% vs. 19.2%), Surgical (25.0% vs. 11.5%) and Infection (21.9% vs. 11.5%) categories compared to the worsened group. The incidence of SSI was improved from 32.26% in 2011 to 0.97% in 2014. Our results suggest that the education and the survey on hand hygiene are effective for reducing HCAI in Cambodia. PMID:27303102

  12. Processing Irradiated Beryllium For Disposal

    Energy Technology Data Exchange (ETDEWEB)

    T. J. Tranter; R. D. Tillotson; N. R. Mann; G. R. Longhurst

    2005-11-01

    The purpose of this research was to develop a process for decontaminating irradiated beryllium that will allow it to be disposed of through normal radwaste channels. Thus, the primary objectives of this ongoing study are to remove the transuranic (TRU) isotopes to less than 100 nCi/g and remove {sup 60}Co, and {sup 137}Cs, to levels that will allow the beryllium to be contact handled. One possible approach that appears to have the most promise is aqueous dissolution and separation of the isotopes by selected solvent extraction followed by precipitation, resulting in a granular form for the beryllium that may be fixed to prevent it from becoming respirable and therefore hazardous. Beryllium metal was dissolved in nitric and fluorboric acids. Isotopes of {sup 241}Am, {sup 239}Pu, {sup 85}Sr, and {sup 137}Cs were then added to make a surrogate beryllium waste solution. A series of batch contacts was performed with the spiked simulant using chlorinated cobalt dicarbollide (CCD) and polyethylene glycol diluted with sulfone to extract the isotopes of Cs and Sr. Another series of batch contacts was performed using a combination of octyl (phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) in tributyl phosphate (TBP) diluted with dodecane for extracting the isotopes of Pu and Am. The results indicate that greater than 99.9% removal can be achieved for each isotope with only three contact stages.

  13. Status of beryllium materials for fusion application

    International Nuclear Information System (INIS)

    The possible use of beryllium as a material for fusion reactors is discussed. Based on the results of recent Russian elaborations, which were not covered previously in the scientific literature, an attempt of complex analysis of the techniques of using beryllium is made. The specific requirements on beryllium as a protective material for first wall and divertor are considered. Also the possibility of creating a fusion grade of beryllium is discussed and an optimum strategy is suggested. (orig.)

  14. Monte Carlo uncertainty analyses for integral beryllium experiments

    CERN Document Server

    Fischer, U; Tsige-Tamirat, H

    2000-01-01

    The novel Monte Carlo technique for calculating point detector sensitivities has been applied to two representative beryllium transmission experiments with the objective to investigate the sensitivity of important responses such as the neutron multiplication and to assess the related uncertainties due to the underlying cross-section data uncertainties. As an important result, it has been revealed that the neutron multiplication power of beryllium can be predicted with good accuracy using state-of-the-art nuclear data evaluations. Severe discrepancies do exist for the spectral neutron flux distribution that would transmit into significant uncertainties of the calculated neutron spectra and of the nuclear blanket performance in blanket design calculations. With regard to this, it is suggested to re-analyse the secondary energy and angle distribution data of beryllium by means of Monte Carlo based sensitivity and uncertainty calculations. Related code development work is underway.

  15. Assessment of occupational health problems and physiological stress among the brick field workers of West Bengal, India

    Directory of Open Access Journals (Sweden)

    Banibrata Das

    2014-08-01

    Full Text Available Objectives: The brick field industry is one of the oldest industries in India, which employs a large number of workers of poor socioeconomic status. The main aim of the present investigation is i to determine the prevalence of musculoskeletal disorders among brick field workers, ii to determine the prevalence of respiratory disorders and physiological stress among brick field workers compared to control workers. Material and Methods: For this study, a total of 220 brick field workers and 130 control subjects were selected randomly. The control subjects were mainly involved in hand-intensive jobs. The Modified Nordic Questionnaire was applied to assess the discomfort felt among both groups of workers. Thermal stress was also assessed by measuring the WBGT index. The pulmonary functions were checked using the spirometry. Physiological assessment of the workload was carried out by recording the heart rate and blood pressure of the workers prior to work and just after work in the field. Results: Brick field workers suffered from pain especially in the lower back (98%, hands (93%, knees (86%, wrists (85%, shoulders (76% and neck (65%. Among the brick-making activities, brick field workers felt discomfort during spading for mud collection (98%, carrying bricks (95% and molding (87%. The results showed a significantly lower p value < 0.001 in FVC, FEV1, FEV1/FVC ratio and PEFR in brick field workers compared to the control group. The post-activity heart rate of the brick field workers was 148.6 beats/min, whereas the systolic and diastolic blood pressure results were 152.8 and 78.5 mm/Hg, respectively. Conclusions: This study concludes that health of the brick field workers was highly affected due to working in unhealthy working conditions for a long period of time.

  16. Assessment of fitness for work in health care workers: biomechanical risk factors.

    Science.gov (United States)

    Violante, E S; Mattioli, S; Camagni, Angela; Bottoli, Elena; Farioli, A; Bonfiglioli, Roberta

    2012-01-01

    In current practice the assessment of fitness for work in health care workers exposed to biomechanical risk factors is often based on conventional approaches rather than on evidence-based guidelines. However, an accurate evaluation of worker's psychophysical resources compared to job demand and potential occupational risk factors is essential in order to properly assess fitness for work. The latest published guidelines on the management of patients suffering from back pain reported that the evidence-based approach can minimize the period of inactivity by encouraging return to work (and to other non-dangerous physical activities) in a relatively short period of time. As for carpal tunnel syndrome, there is no scientific evidence supporting a restriction of physical activities requiring forceful movements of the hand/wrist. PMID:22838297

  17. Using Lymphocyte and Plasma Hsp70 as Biomarkers for Assessing Coke Oven Exposure among Steel Workers

    OpenAIRE

    Yang, Xiaobo; Zheng, Jinping; Bai, Yun; Tian, Fengjie; Yuan, Jing; Sun, Jianya; Liang, Huashan; Guo, Liang; Tan, Hao; Chen, Weihong; Tanguay, Robert M.; Wu, Tangchun

    2007-01-01

    Background Hsp70, an early-response protein induced when organisms are confronted with simple or complicated environmental stresses, can act as either a cellular protector or a danger signal. Objectives The goal of this study was to evaluate levels of lymphocyte and/or plasma Hsp70 as biomarkers for assessing exposure response to complex coke oven emissions (COEs). Methods We recruited 101 coke oven workers and determined levels of polycyclic aromatic hydrocarbon (PAH) exposure, urinary 1-hyd...

  18. Neutron irradiation of beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Gelles, D.S.; Ermi, R.M. [Pacific Northwest National Lab., Richland, WA (United States); Tsai, H. [Argonne National Lab., IL (United States)

    1998-03-01

    Seven subcapsules from the FFTF/MOTA 2B irradiation experiment containing 97 or 100% dense sintered beryllium cylindrical specimens in depleted lithium have been opened and the specimens retrieved for postirradiation examination. Irradiation conditions included 370 C to 1.6 {times} 10{sup 22} n/cm{sup 2}, 425 C to 4.8 {times} 10{sup 22} n/cm{sup 2}, and 550 C to 5.0 {times} 10{sup 22} n/cm{sup 2}. TEM specimens contained in these capsules were also retrieved, but many were broken. Density measurements of the cylindrical specimens showed as much as 1.59% swelling following irradiation at 500 C in 100% dense beryllium. Beryllium at 97% density generally gave slightly lower swelling values.

  19. Knowledge and Practice Assessment of Workers in a Pharmaceutical Company about Prevention of Coronary Artery Disease

    Directory of Open Access Journals (Sweden)

    Yasser Labbafinejad

    2012-10-01

    Full Text Available Coronary artery disease is one of the most common reasons of death around the world. Also, according to previous studies, the incidence of coronary artery disease is rapidly increasing in developing countries such as Iran. The aim of this study was to evaluate the knowledge and practice of pharmaceutical company workers towards the prevention of cardiovascular disease. In this cross sectional study that was conducted in Tehran, 1223 workers of a pharmaceutical company were enrolled. Data was collected using a questionnaire that assessed the level of knowledge and practice of the participants towards coronary artery disease. Regression analysis was used to evaluate the relationship between study variables and the workers knowledge level. The results of this study showed that 49% of the workers were in a good level of knowledge and according to the regression analysis, the female gender, age above 28, education level higher than high school diploma, body mass index above 25 kilograms per square meters, history of hyperlipidemia, history of diabetes, history of hypertension, history of myocardial infarction, daily activity and exercise, were significantly related to a good knowledge towards coronary artery disease. In addition, the mean score of the participants' performance in preventing coronary artery disease was 4.66 out of 9. The results of this study showed that increasing level of knowledge of labors in order to prevent missing specialized work force, leads to imposition of health costs to the industry and the labor society.

  20. Assessment of skeletal muscle fatigue of road maintenance workers based on heart rate monitoring and myotonometry

    Directory of Open Access Journals (Sweden)

    Kalkis Henrijs

    2006-07-01

    Full Text Available Abstract Objective This research work is dedicated to occupational health problems caused by ergonomic risks. The research object was road building industry, where workers have to work very intensively, have long work hours, are working in forced/constrained work postures and overstrain during the work specific parts of their bodies. The aim of this study was to evaluate the work heaviness degree and to estimate the muscle fatigue of workers after one week work cycle. The study group consisted of 10 road construction and maintenance workers and 10 pavers aged between 20 and 60 years. Methods Physical load were analyzed by measuring heart rate (HR, work postures (OWAS and perceived exertion (RPE. Assessments of the muscles strain and functional state (tone were carried out using myotonometric (MYO measurements. The reliability of the statistical processing of heart rate monitoring and myotonometry data was determined using correlating analysis. Results This study showed that that road construction and repairing works should be considered as a hard work according to average metabolic energy consumption 8.1 ± 1.5 kcal/min; paving, in its turn, was a moderately hard work according to 7.2 ± 1.1 kcal/min. Several muscle tone levels were identified allowing subdivision of workers into three conditional categories basing on muscle tone and fatigue: I – absolute muscle relaxation and ability to relax; II – a state of equilibrium, when muscles are able to adapt to the work load and are partly able to relax; and III – muscle fatigue and increased tone. It was also found out that the increase of muscle tone and fatigue mainly depend on workers physical preparedness and length of service, and less – on their age. Conclusion We have concluded that a complex ergonomic analysis consisting of heart rate monitoring, assessment of compulsive working postures and myotonometry is appropriate to assess the work heaviness degree and can provide prognosis of

  1. Assessment of potential doses to workers during postulated accident conditions at the Waste Isolation Pilot Plant

    Energy Technology Data Exchange (ETDEWEB)

    Hoover, M.D.; Farrell, R.F. [DOE, Carlsbad, NM (United States); Newton, G.J.

    1995-12-01

    The recent 1995 WIPP Safety Analysis Report (SAR) Update provided detailed analyses of potential radiation doses to members of the public at the site boundary during postulated accident scenarios at the U.S. Department of Energy`s Waste Isolation Pilot Plant (WIPP). The SAR Update addressed the complete spectrum of potential accidents associated with handling and emplacing transuranic waste at WIPP, including damage to waste drums from fires, punctures, drops, and other disruptions. The report focused on the adequacy of the multiple layers of safety practice ({open_quotes}defense-in-depth{close_quotes}) at WIPP, which are designed to (1) reduce the likelihood of accidents and (2) limit the consequences of those accidents. The safeguards which contribute to defense-in-depth at WIPP include a substantial array of inherent design features, engineered controls, and administrative procedures. The SAR Update confirmed that the defense-in-depth at WIPP is adequate to assure the protection of the public and environment. As a supplement to the 1995 SAR Update, we have conducted additional analyses to confirm that these controls will also provide adequate protection to workers at the WIPP. The approaches and results of the worker dose assessment are summarized here. In conformance with the guidance of DOE Standard 3009-94, we emphasize that use of these evaluation guidelines is not intended to imply that these numbers constitute acceptable limits for worker exposures under accident conditions. However, in conjunction with the extensive safety assessment in the 1995 SAR Update, these results indicate that the Carlsbad Area Office strategy for the assessment of hazards and accidents assures the protection of workers, members of the public, and the environment.

  2. Characterization and Health Risk Assessment of Volatile Organic Compounds in Gas Service Station Workers

    Directory of Open Access Journals (Sweden)

    Duangduan Yimrungruang

    2008-07-01

    Full Text Available Gas service station workers who work near volatile organic compounds (VOCs sources, such as gasoline vapor emissions, and motor vehicle exhausts, may be exposed to highly elevated VOCs levels. This study investigates air samples from gas service stations in Thailand to evaluate the health risks following inhalation exposure. Personal air samplings were obtained at nine gas service stations in Chonburi, Thailand from October to December 2007. The concentrations of benzene, toluene, ethylbenzene, xylenes, and hexane in the air from the workplaces were significantly higher than in a control group of office workers (p<0.05. However, all VOCs in these air samples were lower than TWA limit of Thailand and the OSHA standard. Samples of urine, collected after 8-h work periods which were analyzed for VOCs metabolites, including t,t muconic acid, hippuric acid, mandelic acid and m-hippuric acid, demonstrate that the average levels of metabolites in gas service station workers and in controls were close, except for t,t muconic acid of gas service station workers which displayed higher levels than the in the controls. The lifetime cancer and noncancer risks for the workers exposed to VOCs were also assessed. Results show that all nine gas service stations in this study had a elevated lifetime cancer risk ranging from 53 to 630 per million, thus exceeding the normal risk of 1 per million. For noncancer risks, the levels in all gas stations ranged between 0.03 and 0.4, which is well below the reference hazard level of 1.0. Benzene may the most important cause of both cancer and noncancer risk followed by 1,3 butadiene.

  3. Assessment of zero gravity effects on space worker health and safety

    Science.gov (United States)

    1980-01-01

    One objective of the study is to assess the effects of all currently known deviations from normal of medical, physiological, and biochemical parameters which appear to be due to zero gravity (zero-g) environment and to acceleration and deceleration to be experienced, as outlined in the references Solar Power Satellites (SPS) design, by space worker. Study results include identification of possible health or safety effects on space workers either immediate or delayed due to the zero gravity environment and acceleration and deceleration; estimation of the probability that an individual will be adversely affected; description of the possible consequence to work efficiency in persons adversely affected; and description of the possible/probable consequences to immediate and future health of individuals exposed to this environment. A research plan, which addresses the uncertainties in current knowledge regarding the health and safety hazards to exposed SPS space workers, is presented. Although most adverse affects experienced during space flight soon disappeared upon return to the Earth's environment, there remains a definite concern for the long-term effects to SPS space workers who might spend as much as half their time in space during a possible five year career period. The proposed 90 day up/90 day down cycle, coupled with the fact that most of the effects of weightlessness may persist throughout the flight along with the realization that recovery may occupy much of the terrestrial stay, may keep the SPS workers in a deviant physical condition or state of flux for 60 to 100% of their five year career.

  4. Assessment of zero gravity effects on space worker health and safety

    Energy Technology Data Exchange (ETDEWEB)

    1980-11-01

    One objective of the study is to assess the effects of all currently known deviations from normal of medical, physiological, and biochemical parameters which appear to be due to zero gravity (zero-g) environment and to acceleration and deceleration to be experienced, as outlined in the reference Solar Power Satellite (SPS) design, by space worker. Study results include identification of possible health or safety effects on space workers - either immediate or delayed - due to the zero gravity environment and acceleration and deceleration; estimation of the probability that an individual will be adversely affected; description of the possible consequence to work efficiently in persons adversely affected; and description of the possible/probable consequences to immediate and future health of individuals exposed to this environment. A research plan, which addresses the uncertainties in current knowledge regarding the health and safety hazards to exposed SPS space workers, is presented. Although most adverse affects experienced during space flight soon disappeared upon return to the Earth's environment, there remains a definite concern for the long-term effects to SPS space workers who might spend as much as half their time in space during a possible five-year career period. The proposed 90-day up/90 day down cycle, coupled with the fact that most of the effects of weightlessness may persist throughout the flight along with the realization that recovery may occupy much of the terrestrial stay, may keep the SPS workers in a deviant physical condition or state of flux for 60 to 100% of their five-year career. (JGB)

  5. Assessment of workers' exposure to bioaerosols in a French cheese factory.

    Science.gov (United States)

    Simon, Xavier; Duquenne, Philippe

    2014-07-01

    Hundreds of different cheeses are produced in France, where 23.9kg of cheese were consumed per inhabitant in 2009, when it was ranked the second cheese-consuming nation. To meet this considerable demand, a large number of cheese factories exist where many workers, especially cheese washers, may be exposed to fungal bioaerosols that can lead to adverse toxinic and allergic effects. Airborne bacteria, fragments, or microbial by-products (endotoxins) are also found and contribute to total worker exposure. However, there is almost no published data concerning worker exposure or characteristics of bioaerosols emitted during these activities. Here, we measured the parameters (concentrations, species present, and size distribution) of the culturable fungal bioaerosol emitted in a French natural-rind cheese-maturing cellar. Concentrations of airborne bacteria and endotoxins were also measured. The main tasks were investigated using stationary or personal sampling over three consecutive days. Depending on the work area, high concentrations of culturable mesophilic microorganisms were measured (using closed-face cassettes): from 10(4) to 2×10(8) CFU m(-3) for fungi and from 10(3) to 10(6) CFU m(-3) for bacteria. These concentrations are 10- to 100000-fold higher than those measured at two reference points (indoor and outdoor) that are assumed not to be contaminated by the plant's activities. Endotoxin concentrations were between 10 and 300 EU m(-3) in the plant. Exposure was further assessed by identifying the predominant culturable fungi (allergenic Mucor fuscus and Penicillium sp.) and by measuring particle size distributions (cascade impactor). Airborne fungal entities (spores, mycelium strands and fragments, agglomerates, etc.) were found with aerodynamic diameters from 3 to over 20 µm. A metrological approach was used to fully characterize the culturable fungal aerosols generated during cheese maturing in this plant. The results show that workers are exposed to

  6. Integrated exposure assessment of sewage workers to genotoxicants: an urinary biomarker approach and oxidative stress evaluation

    Directory of Open Access Journals (Sweden)

    Sari-Minodier Irène

    2011-03-01

    Full Text Available Abstract Background Sewage workers are exposed to multiple chemicals among which many are suspected genotoxicants. Therefore, they might incur DNA damage and oxidative stress. We aimed to explore integrated urinary biomarkers, assessing the overall urine genotoxicity by in vitro comet and micronucleus assays and measuring urinary 8-oxo-2'-deoxyguanosine. Methods During three consecutive working days, polycyclic aromatic hydrocarbons and volatile organic compounds were sampled in workplace air of 34 sewage and 30 office workers, as indicators of airborne exposure. The last day, subjects collected their 24 hours urine. Genotoxicity of urinary extracts was assessed by comet and micronucleus assays on a HepG2 cell line. Using competitive enzymatic immunoassay we evaluated the 24 hours urinary 8-oxo-2'-deoxyguanosine excretion. Benzo(apyrene toxicity equivalent factors and inhalation unit risk for Benzo(apyrene and benzene were used to give an estimate of cancer risk levels. Results Workplace air concentrations of polycyclic aromatic hydrocarbons (e.g. 23.7 [range 2.4-104.6] ng.m-3 for fluoranthene and volatile organic compounds (e.g. 19.1 ± 2.9 [standard error] μ.m-3 for benzene were elevated in sewage compared to office workplaces (P P Conclusions The integrated and non-specific urinary biomarkers of exposure showed that sewage workers experience exposure to mixtures of genotoxicants in the workplace.

  7. Assessment of plutonium exposures for an epidemiological study of US nuclear workers

    International Nuclear Information System (INIS)

    An ongoing case-control study evaluating the association between workplace external radiation exposures and leukaemia mortality required an assessment of internal plutonium exposures as a potential confounder. Of the study participants, 1092 were employed at four Dept. of Energy sites where plutonium-bearing materials were processed or stored. Exposures were assessed by first categorising exposure potentials based on available bioassay data, then estimating doses for workers in the highest categories using recent recommendations of the International Commission on Radiological Protection. Given the aetiology of leukaemia, equivalent dose to active bone marrow was chosen as the exposure variable. There were 556 workers each with at least one plutonium bioassay result, assigned to one of three evaluation categories. Dose estimates were made for 115 workers resulting in a collective equivalent dose of 2.1 person-Sv for 2822 exposure-years, compared with 29.8 person-Sv estimated from photon exposures. Modelling uncertainties were examined by comparison of results from independent analyses and by Monte Carlo simulation. (authors)

  8. Assessment of acetylcholinesterase and butyrylcholinesterase activities in blood plasma of agriculture workers

    Directory of Open Access Journals (Sweden)

    V Dhananjayan

    2012-01-01

    Full Text Available Background: Cholinesterase determination indicates whether the person has been under pesticide exposure is not. It is recommended that the worker′s cholinesterase level should be assessed for workers at a pesticide applied region. Hence, cholinesterase activities in blood samples of agricultural workers exposed to vegetables and grape cultivation with age matched, unexposed workers, who never had any exposure to pesticides, were estimated. Methods: The detailed occupational history and lifestyle characters were obtained by questionnaire. Cholinesterase activity was determined by the method of Ellman as modified by Chambers and Chambers. Results: AChE was ranging from 1.65 to 3.54μmoles/min/ml in exposed subjects where as it was ranged from 2.22 to 3.51μmoles/min/ml in control subjects. BChE activity was ranging from 0.16 to 5.2μmoles/min/ml among exposed subjects, where as it was ranged from 2.19 to 5.06μmoles/min/ml in control subjects. The results showed statistically significant reduction in enzyme activities (AChE 14%; BChE 56% among exposed subjects. Conclusion: It was concluded that the reduction in cholinesterase activity may lead to varieties of effects. Hence it is compulsory to use protective gadgets during pesticide spray. Further a continuous biomonitoring study is recommended to assess pesticide exposure.

  9. Inhalation cancer risk assessment of hexavalent chromium based on updated mortality for Painesville chromate production workers

    Science.gov (United States)

    Proctor, Deborah M; Suh, Mina; Mittal, Liz; Hirsch, Shawn; Valdes Salgado, Raydel; Bartlett, Chris; Van Landingham, Cynthia; Rohr, Annette; Crump, Kenny

    2016-01-01

    The exposure-response for hexavalent chromium (Cr(VI))-induced lung cancer among workers of the Painesville Ohio chromate production facility has been used internationally for quantitative risk assessment of environmental and occupational exposures to airborne Cr(VI). We updated the mortality of 714 Painesville workers (including 198 short-term workers) through December 2011, reconstructed exposures, and conducted exposure-response modeling using Poisson and Cox regressions to provide quantitative lung cancer risk estimates. The average length of follow-up was 34.4 years with 24,535 person-years at risk. Lung cancer was significantly increased for the cohort (standardized mortality ratio (SMR)=186; 95% confidence interval (CI) 145–228), for those hired before 1959, those with >30-year tenure, and those with cumulative exposure >1.41 mg/m3-years or highest monthly exposures >0.26 mg/m3. Of the models assessed, the linear Cox model with unlagged cumulative exposure provided the best fit and was preferred. Smoking and age at hire were also significant predictors of lung cancer mortality. Adjusting for these variables, the occupational unit risk was 0.00166 (95% CI 0.000713–0.00349), and the environmental unit risk was 0.00832 (95% CI 0.00359–0.0174), which are 20% and 15% lower, respectively, than values developed in a previous study of this cohort. PMID:26669850

  10. Reactivity test between beryllium and copper

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, H. [Japan Atomic Energy Research Institute, Ibaraki-ken (Japan); Kato, M. [NGK Insulators, Ltd., Aichi-ken (Japan)

    1995-09-01

    Beryllium has been expected for using as plasma facing material on ITER. And, copper alloy has been proposed as heat sink material behind plasma facing components. Therefore, both materials must be joined. However, the elementary process of reaction between beryllium and copper alloy does not clear in detail. For example, other authors reported that beryllium reacted with copper at high temperature, but it was not obvious about the generation of reaction products and increasing of the reaction layer. In the present work, from this point, for clarifying the elementary process of reaction between beryllium and copper, the out-of-pile compatibility tests were conducted with diffusion couples of beryllium and copper which were inserted in the capsule filled with high purity helium gas (6N). Annealing temperatures were 300, 400, 500, 600 and 700{degrees}C, and annealing periods were 100, 300 and 1000h. Beryllium specimens were hot pressed beryllium, and copper specimens were OFC (Oxygen Free Copper).

  11. Extraction and optical fluorescence method for the measurement of trace beryllium in soils.

    Science.gov (United States)

    Agrawal, Anoop; Cronin, John P; Agrawal, Akshay; Tonazzi, Juan C L; Adams, Lori; Ashley, Kevin; Brisson, Michael J; Duran, Brandy; Whitney, Gary; Burrell, Anthony K; McCleskey, T Mark; Robbins, James; White, Kenneth T

    2008-03-15

    Beryllium metal and beryllium oxide are important industrial materials used in a variety of applications in the electronics, nuclear energy, and aerospace industries. These materials are highly toxic, they must be disposed of with care, and exposed workers need to be protected. Recently, a new analytical method was developed that uses dilute ammonium bifluoride for extraction of beryllium and a high quantum yield optical fluorescence reagent to determine trace amounts of beryllium in airborne and surface samples. The sample preparation and analysis procedure was published by both ASTM International and the National Institute for Occupational Safety and Health (NIOSH). The main advantages of this method are its sensitivity, simplicity, use of lower toxicity materials, and low capital costs. Use of the technique for analyzing soils has been initiated to help meet a need at several of the U.S. Department of Energy legacy sites. So far this work has mainly concentrated on developing a dissolution protocol for effectively extracting beryllium from a variety of soils and sediments so that these can be analyzed by optical fluorescence. Certified reference materials (CRM) of crushed rock and soils were analyzed for beryllium content using fluorescence, and results agree quantitatively with reference values.

  12. Assessment of the occupational radiation exposure doses to workers at INMOL Pakistan (2007-11)

    International Nuclear Information System (INIS)

    The assessment of occupationally exposed medical radiation workers at the Institute of Nuclear Medicine and Oncology (INMOL) (Pakistan)) has been performed. The whole-body radiation exposure doses of 120 workers in nuclear medicine (NM), radiotherapy (RT) and diagnostic radiology (DR) were measured by using the film badge dosimetry technique for the time interval (2007-11) and their results presented. The annual average effective doses in NM, RT and DR were found to be well below the permissible annual limit of 20 mSv (averaged over a period of 5 consecutive y). The declining trend observed in the annual average dose values during the time interval (2007-11) is an indication of ameliorated radiation protection practices at INMOL (Pakistan)). (authors)

  13. Assessment of selected B cells populations in the workers of X-ray departments

    Directory of Open Access Journals (Sweden)

    Piotr Kłuciński

    2014-08-01

    Full Text Available Objectives: Workers of X-ray departments are occupationally exposed to long-term low levels of ionizing radiation (LLIR, which may affect their humoral immunity. The aim of the study was to assess the influence of LLIR on the number and proportion of B cells (CD19+, B1 cells (CD5+CD19+ and memory B cells (CD27+CD19+ in peripheral blood of such workers. Materials and Methods: In the study group of 47 X-ray departments workers and the control group consisting of 38 persons, the number and percentage of CD19+, CD5+CD19+, CD27+CD19+ cells as well as CD5+CD19+/CD19+ and CD27+CD19+/CD19+ cell ratios were assessed using flow cytometry. Additionally, the study group was divided into 2 groups by the length of employment below and over 15 years and analysis adjusted for age and smoking habit was performed. Results: The total number of CD19+ cells showed significant increase in the group of workers in comparison with the persons from the control group, whereas the percentage of CD5+CD19+ cells as well as CD27+CD19+/CD19+ and CD5+CD19+/CD19+ cell ratios were lower. Percentage, number of CD5+CD19+ cells and CD5+CD19+/CD19+ cell ratio were significantly lower in the workers with length of employment longer than 15 years in comparison with those employed below 15 years. Moreover, we found positive associations between the number of CD19+ cells and employment as well as smoking habit, whereas the number of CD5+CD19+ cells was positively associated with cigarette smoking alone. Percentage of CD5+CD19+ cells as well as CD5+CD19+/CD19+ and CD27+CD19+/CD19+ cell ratios were negatively correlated with employment. Conclusions: The study suggests association between the suppressive influence of low level ionizing radiation on circulating in peripheral blood, especially of B1 cells as well as of memory B cells, in workers of X-ray units, which is adverse in relation to microbiological threat.

  14. Exposure of workers to the risks related to electromagnetic fields. Guide for risk assessment

    International Nuclear Information System (INIS)

    This guide aims at helping companies to prevent risks related to worker exposure to electromagnetic fields, and at simplifying the assessment approach. After some generalities of electromagnetic fields (notions of electromagnetic spectrum, electric, magnetic and electromagnetic fields, wavelength and frequency, reactive near- or far-field area, work environment), this report describes the effect of an exposure with respect to frequencies (under 100 khz, over 10 MHz, between 100 khz and 10 MHz), recalls the regulation in occupational environment. It presents some generalities on exposure sources, and methods and ways for a simplified risk assessment (equipment inventory and characterization, CE-labelled equipment). It addresses various aspects of a deepened risk assessment: the exposure assessment (emitted field measurement, workstation analysis, maximum exposure, determination of exposure action level or VDA), the indirect effects (contact with a metallic object within the field, projection of ferromagnetic objects, initiation of firing electric devices, fires and explosions), and workers with specific risks (those bearing active implants or passive ferromagnetic implants, pregnant women). The last part addresses actions aimed at reducing the exposure. Eight industrial applications are more particularly addressed and discussed at the end of each chapter: induction-based devices (welding, fusion, heating, surface treatment, so on), magnetizers and demagnetizers, magneto-scopic devices, magnetic resonance imagery devices, electrolytic cells, heating or welding devices based on dielectric losses, and microwave ovens

  15. Assessment of impact of high particulate concentration on peak expiratory flow rate of lungs of sand stone quarry workers.

    Science.gov (United States)

    Singh, Suresh Kumar; Chowdhary, G R; Purohit, Gopal

    2006-12-01

    This study was designed to assess the impact of high particulate concentration on peak expiratory flow rate of lungs of sand stone quarry workers. The workers were engaged in different types of activities such as drilling, loading and dressing. These different working conditions had different concentrations of RSPM, leading to different exposure levels in workers. It was found that exposure duration and exposure concentrations were the main factors responsible for damage to the respiratory tracts of the workers. The particles were deposited at various areas of the respiratory system and reduced the peak flow rate. It was also revealed from the study that most of the workers suffered from silicosis if the exposure duration was more than 20 years.

  16. Beryllium - A Unique Material in Nuclear Applications

    International Nuclear Information System (INIS)

    Beryllium, due to its unique combination of structural, chemical, atomic number, and neutron absorption cross section characteristics, has been used successfully as a neutron reflector for three generations of nuclear test reactors at the Idaho National Engineering and Environmental Laboratory (INEEL). The Advanced Test Reactor (ATR), the largest test reactor in the world, has utilized five successive beryllium neutron reflectors and is scheduled for continued operation with a sixth beryllium reflector. A high radiation environment in a test reactor produces radiation damage and other changes in beryllium. These changes necessitate safety analysis of the beryllium, methods to predict performance, and appropriate surveillances. Other nuclear applications also utilize beryllium. Beryllium, given its unique atomic, physical, and chemical characteristics, is widely used as a ''window'' for x-rays and gamma rays. Beryllium, intimately mixed with high-energy alpha radiation emitters has been successfully used to produce neutron sources. This paper addresses operational experience and methodologies associated with the use of beryllium in nuclear test reactors and in ''windows'' for x-rays and gamma rays. Other nuclear applications utilizing beryllium are also discussed

  17. South African farm workers' interpretation of risk assessment data expressed as pictograms on pesticide labels

    International Nuclear Information System (INIS)

    Pesticide companies and regulators in developing countries use the United Nations Food and Agricultural Organization (FAO) recommended pictograms on pesticide labels to communicate risk information based on toxicological and environmental risk assessment data. The pesticide label not only is often the only access people have to pesticide risk information, but also in many countries is a legally binding document. As a result of the crucial role pesticide labels play in protecting health and the environment and as a legal instrument, pictograms are used to overcome literacy challenges in transmitting pesticide risk information. Yet, this risk communication tool is often prone to misinterpretations of the risk information which results in hazardous exposures to pesticides for farm workers and end-users generally. In this paper, results are presented from a study with 115 farm workers on commercial vineyards in the Western Cape, South Africa, assessing their interpretations of 10 commonly used pictograms. A standardized questionnaire based on four commonly used pesticide labels was administered. Overall, 50% or more of the study farm workers had misleading, incorrect and critically confused interpretations of the label pictograms. Interpretations often reflected farm workers' social and cultural frames of reference rather than the technically intended risk information. For example, the pictogram indicating a pesticide's toxicity requires boots must be worn, evoked interpretations of 'dangerous to pedestrians' and 'don't walk through pesticides'. Furthermore, there was a gender variation in pictogram comprehension whereby males generally had more correct interpretations than females. This is a result both of a lack of training for women who are assumed to not work with pesticides, as well as a lack of pictograms relevant for female exposures. These findings challenge the viability of the United Nations current initiative to globally harmonize pictograms used on all

  18. Beryllium abundances in stars with planets:Extending the sample

    CERN Document Server

    Gálvez-Ortiz, M C; Hernández, J I González; Israelian, G; Santos, N C; Rebolo, R; Ecuvillon, A

    2011-01-01

    Context: Chemical abundances of light elements as beryllium in planet-host stars allow us to study the planet formation scenarios and/or investigate possible surface pollution processes. Aims: We present here an extension of previous beryllium abundance studies. The complete sample consists of 70 stars hosting planets and 30 stars without known planetary companions. The aim of this paper is to further assess the trends found in previous studies with less number of objects. This will provide more information on the processes of depletion and mixing of light elements in the interior of late type stars, and will provide possible explanations for the abundance differences between stars that host planets and "single" stars. Methods: Using high resolution UVES spectra, we measure beryllium abundances of 26 stars that host planets and 1 "single" star mainly using the \\lambda 3131.065 A Be II line, by fitting synthetic spectra to the observational data. We also compile beryllium abundance measurements of 44 stars hos...

  19. Mutagenicity, carcinogenicity and teratogenicity of beryllium.

    Science.gov (United States)

    Léonard, A; Lauwerys, R

    1987-07-01

    The carcinogenicity of a number of beryllium compounds has been confirmed in experiments on laboratory animals and this metal has to be treated as a possible carcinogenic threat to man. These carcinogenic properties are associated with mutagenic activity as shown by the results of short-term tests performed in vitro with beryllium chloride and beryllium sulfate. These soluble beryllium compounds can produce some infidelity of in vitro synthesis, forward gene mutations in microorganisms and in mammalian cells. They are also able to induce cell transformation. In addition to the positive results obtained in several short-term assays beryllium compounds have been found to bind to nucleoproteins, to inhibit certain enzymes needed for DNA synthesis, to bind nucleic acids to cell membranes and to inhibit microtubule polymerization. The teratogenicity of beryllium salts is relatively unknown and needs additional investigation.

  20. Assessment of Cold Stress and Its Effects on Workers in a Cold-Storage Warehouse

    OpenAIRE

    Farhang Akbar-Khanzadeh; Mohammad–Hossein Sajadi; Keramat Nouri Jelyani; Farideh Golbabaei

    2009-01-01

    Exposure to cold work environment is an occupational health hazard and poses adverse effect on workers health, performance and productivity. This study was performed in a cold food-storage warehouse complex in Tehran-Iran in order to evaluate the workers' exposure to cold stress. Twenty nine exposed workers and 33 non-exposed workers as control subject were included in this study. Climatic factors were measured based on ISO 7996 at the three levels of workers height. Physiological factor...

  1. Inhibited solid propellant composition containing beryllium hydride

    Science.gov (United States)

    Thompson, W. W. (Inventor)

    1978-01-01

    An object of this invention is to provide a composition of beryllium hydride and carboxy-terminated polybutadiene which is stable. Another object of this invention is to provide a method for inhibiting the reactivity of beryllium hydride toward carboxy-terminated polybutadiene. It was found that a small amount of lecithin inhibits the reaction of beryllium hydride with the acid groups in carboxy terminated polybutadiene.

  2. Recommended design correlations for S-65 beryllium

    International Nuclear Information System (INIS)

    The properties of tritium and helium behavior in irradiated beryllium are reviewed, along with the thermal-mechanical properties needed for ITER design analysis. Correlations are developed to describe the performance of beryllium in a fusion reactor environment. While this paper focuses on the use of beryllium as a plasma-facing component (PFC) material, the correlations presented here can also be used to describe the performance of beryllium as a neutron multiplier for a tritium breeding blanket. The performance properties for beryllium are subdivided into two categories: properties which do not change with irradiation damage to the bulk of the material; and properties which are degraded by neutron irradiation. The approach taken in developing properties correlations is to describe the behavior of dense, pressed S-65 beryllium as a function of temperature. As there are essentially no data on the performance of porous and/or irradiated S-65 beryllium, the degradation of properties with as-fabricated porosity and irradiation are determined form the broad data base on S-200F, as well as other types and grades, and applied to S-65 beryllium by scaling factors. The resulting correlations can be used for Be produced by vacuum hot pressing (VHP) and cold-pressing (CP)/sintering(S)/hot-isostatic-pressing(HIP). The performance of plasma-sprayed beryllium is discussed but not quantified

  3. U.S. Department of Energy worker health risk evaluation methodology for assessing risks associated with environmental restoration and waste management

    Energy Technology Data Exchange (ETDEWEB)

    Blaylock, B.P.; Legg, J.; Travis, C.C. [Oak Ridge National Lab., TN (United States). Center for Risk Management; Simek, M.A.; Sutherland, J. [Univ. of Tennessee, Knoxville, TN (United States); Scofield, P.A. [Office of Environmental Compliance and Documentation (United States)

    1995-06-01

    This document describes a worker health risk evaluation methodology for assessing risks associated with Environmental Restoration (ER) and Waste Management (WM). The methodology is appropriate for estimating worker risks across the Department of Energy (DOE) Complex at both programmatic and site-specific levels. This document supports the worker health risk methodology used to perform the human health risk assessment portion of the DOE Programmatic Environmental Impact Statement (PEIS) although it has applications beyond the PEIS, such as installation-wide worker risk assessments, screening-level assessments, and site-specific assessments.

  4. Orthopaedic surgeries - assessment of ionising radiations exposure in health care workers

    Energy Technology Data Exchange (ETDEWEB)

    Leite, E.S.; Uva, A.S. [Lisbon Univ., National School of Public Health/New (Portugal)

    2006-07-01

    Full text of publication follows: 1. Objectives: The health care workers are exposed to ionizing radiations during their activities. In the operating rooms, the ionizing radiations are used in orthopaedic surgery and the dose depends on some factors, like the characteristics of the equipment. This study aims to: Estimate the occupational dose of ionizing radiations exposure of the orthopaedic doctors and nurses during the orthopaedic surgeries, in a Portuguese operating room; Sensitize the health care workers to use the individual dosimeter and to adopt radiation preventive measures. 2. Population and methods The study was conducted on nine Orthopaedic doctors and two nurses of an operating room of a hospital in Lisbon neighborhoods. We made a risk evaluating concerning: the radiations dose in different points, corresponding to gonads, hands and crystalline lens levels of all the professionals, during the surgeries; the average period of radiation in the orthopaedic surgeries; the number of annual orthopaedic surgeries, looking for that in the surgeries registers, to estimate the annual ionizing radiations dose of each orthopaedic doctor and nurse. 3. Results The annual doses estimated at different levels for orthopaedic doctors were the following: gonads: between 20,63 and 68,75 mGy; hands: 4,95 16,50 mGy; crystalline lens: 8,25 27,50 mGy). For the orthopaedic nurses: gonads: 130,63 151,25 mGy; hands: 31,35 36,30 mGy; crystalline lens 52,25 60,25 mGy. 4. Conclusions Although the location and positions of health care workers are not the same during the different surgeries and the equipment has an automatic control of the X ray emission, the annual ionizing radiations dose exposure for health care workers is an important one. The risk rating justifies the use of individual dosimeters for better individual dose assessment as part of an ionizing radiations prevention program. As a matter of fact preventive measures begin with a good quantitative risk assessment of

  5. Orthopaedic surgeries - assessment of ionising radiations exposure in health care workers

    International Nuclear Information System (INIS)

    Full text of publication follows: 1. Objectives: The health care workers are exposed to ionizing radiations during their activities. In the operating rooms, the ionizing radiations are used in orthopaedic surgery and the dose depends on some factors, like the characteristics of the equipment. This study aims to: Estimate the occupational dose of ionizing radiations exposure of the orthopaedic doctors and nurses during the orthopaedic surgeries, in a Portuguese operating room; Sensitize the health care workers to use the individual dosimeter and to adopt radiation preventive measures. 2. Population and methods The study was conducted on nine Orthopaedic doctors and two nurses of an operating room of a hospital in Lisbon neighborhoods. We made a risk evaluating concerning: the radiations dose in different points, corresponding to gonads, hands and crystalline lens levels of all the professionals, during the surgeries; the average period of radiation in the orthopaedic surgeries; the number of annual orthopaedic surgeries, looking for that in the surgeries registers, to estimate the annual ionizing radiations dose of each orthopaedic doctor and nurse. 3. Results The annual doses estimated at different levels for orthopaedic doctors were the following: gonads: between 20,63 and 68,75 mGy; hands: 4,95 16,50 mGy; crystalline lens: 8,25 27,50 mGy). For the orthopaedic nurses: gonads: 130,63 151,25 mGy; hands: 31,35 36,30 mGy; crystalline lens 52,25 60,25 mGy. 4. Conclusions Although the location and positions of health care workers are not the same during the different surgeries and the equipment has an automatic control of the X ray emission, the annual ionizing radiations dose exposure for health care workers is an important one. The risk rating justifies the use of individual dosimeters for better individual dose assessment as part of an ionizing radiations prevention program. As a matter of fact preventive measures begin with a good quantitative risk assessment of

  6. Are Care Takers of Link WorkerAND#8217;s Scheme of HIV/AIDS Knowledgeable Enouth? Assessment Study of Link Workers Scheme in Surat District

    Directory of Open Access Journals (Sweden)

    Parmar Rohit

    2012-04-01

    Full Text Available Introduction: Gujarat State AIDS Control Society with support from UNICEF Gujarat has initiated as unique project for prevention of HIV /AIDS at rural set up since 2008, which is known as Link Workers’ scheme. Link Workers (LWs are working in each cluster of villages around a 5,000+ population village which will serve as the node for intervention. They are supported in their work by village level volunteers selected from the available groups in the community. Methodology: 140 Link workers and 70 volunteers from 70 villages of 14 blocks of district Surat were invited for the study. Due to few vacant posts, total 183 participants took part in the study; out of these 117 were link workers (LWs while 66 were volunteers. Their Knowledge regarding HIV/AIDS and STI were assessed on a predesigned pretested semi structured study tool. Result: 96.59% link workers and 93.44% volunteers had knowledge about condom use as a method of preventing HIV infection. The concern issue is that only 11.11% LWs and 13.64% volunteers revealed that HIV testing during ANC check up can also prevent HIV transmission from mother to child, inspite of receiving induction training. Only 74.36% LWs and 68.31% volunteers were able to tell about three or more HIV preventive methods. Recommendations: Refresher training and exposure visit to HIV care centres are needed for these workers to strengthen their knowledge. [National J of Med Res 2012; 2(2.000: 173-175

  7. Assessment of work stress and alcohol use in mental health care workers

    Directory of Open Access Journals (Sweden)

    Athanasiadis T.

    2011-10-01

    Full Text Available Aim: The documentation and assessment of general work stressors and alcohol use on mental health care workers as well as the relationship between them. Material and method: The sample consisted of 300 mental health care workers who worked in Private and Public Psychiatric Clinics and Psychiatric Hospitals of the country (Hellas. The collection of empirical material was done by using a questionnaire that included a scale of 34 questions for detecting occupational stress factors, the self-esteem scale of the Spielberger and questions about alcohol use. The statistical analysis of data was done with the statistical program SPSS version 15.0 using Student t - test, the ANOVA analysis of variance test and x2 test. Results: Higher frequency occupational stress factors appeared in Nurses rather than Doctors as well as in employees in Private Psychiatric Clinics rather than employees in the Public sector. The fact that Nurses have higher frequency in stressors rather than Doctors is reflected in measurements of anxiety, as a state as well as a personality trait. Also the employees of Private Psychiatric Clinics exhibit greater indicator of anxiety as a personality trait than the employees of the Public sector. Regarding alcohol use (concept of efficiency and normal consumption quantity it was found to be positively associated with the age of the employees. Also the concept of the effectiveness of alcohol in tackling work stress is associated with some occupational stress factors (dangerous conditions of work, rolling working hours. Conclusions: Factors such as specialty and the type of workplace (Public, Private sector affect the stress experienced by the mental health professional. The view of alcohol as a means of relieving working stress is associated with certain stressors of work and the worker's age.

  8. United Kingdom Beryllium Registry: mortality and autopsy study.

    Science.gov (United States)

    Williams, W J

    1996-01-01

    This report is based on 30 deaths from chronic beryllium disease (CBD) in the United Kingdom with details of 19 autopsies. The majority were fluorescent lamp workers and machinists who died from respiratory failure. There were no cases of lung cancer. The survival times ranged from less than 1 to 29 years and was longest in machinists. All of the workers showed interstitial pulmonary fibrosis with varying degrees of cystic change. The majority showed hyalinized, and a few active sarcoid-type, granulomas. Extrathoracic granulomas, as in a U.K. sarcoid autopsy series, were rare. A notable difference was the absence of myocardial involvement in CBD compared to an incidence of 20% in the sarcoid autopsies. The detection of beryllium in the criteria for diagnosis is emphasized and the cases classified as definite include 12 of 19 positive analysis, 6 of 19, negative or unavailable analysis. The remaining case was classified as dubious because, despite a positive analysis, granulomas were absent. The main differential diagnosis is sarcoidosis. Images Figure 1. Figure 2. Figure 3. PMID:8933040

  9. Assessment of the effects of the zero gravity environment on the health and safety of space workers. Summary report

    Energy Technology Data Exchange (ETDEWEB)

    1980-02-18

    A review was conducted of currently available information relating to adverse effects to the health and safety that SPS space workers may experience. Currently available information on the responses of humans to space flight is somewhat limited and was obtained under conditions which are grossly different from conditions to be experienced by future space workers. The limitations in information and differences in conditions have been considered in the assessment of potential health and safety hazards to the SPS space workers. The study did not disclose any adverse effects that would result in long term deviations to the medical or physiological health of space workers so long as proper preventive or ameleorating actions were taken.

  10. A probabilistic approach to quantitatively assess the inhalation risk for airborne endotoxin in cotton textile workers

    International Nuclear Information System (INIS)

    Endotoxin, a component of gram-negative bacterial cell walls, is a proinflammatory agent that induces local and systemic inflammatory responses in normal subjects which can contribute to the risk of developing asthma and chronic obstructive lung diseases. A probabilistic approach linking models of exposure, internal dosimetry, and health effects were carried out to quantitatively assess the potential inhalation risk of airborne endotoxin for workers in cotton textile plants. Combining empirical data and modeling results, we show that the half-maximum effects of the endotoxin dose (ED50) were estimated to be 3.3 x 105 (95% confidence interval (CI): 1.9-14.7 x 105) endotoxin units (EU) for the blood C-reactive protein (CRP) concentration, 1.1 x 105 (95% CI: 0.6-1.7 x 105) EU for the blood polymorphonuclear neutrophil (PMN) count, and 1.5 x 105 (95% CI: 0.4-2.5 x 105) EU for the sputum PMN count. Our study offers a risk-management framework for discussing future establishment of limits for respiratory exposure to airborne endotoxin for workers in cotton textile plants.

  11. Applying the revised Chinese Job Content Questionnaire to assess psychosocial work conditions among Taiwan's hospital workers

    Directory of Open Access Journals (Sweden)

    Castillo Roberto

    2011-06-01

    Full Text Available Abstract Background For hospital accreditation and health promotion reasons, we examined whether the 22-item Job Content Questionnaire (JCQ could be applied to evaluate job strain of individual hospital employees and to determine the number of factors extracted from JCQ. Additionally, we developed an Excel module of self-evaluation diagnostic system for consultation with experts. Methods To develop an Excel-based self-evaluation diagnostic system for consultation to experts to make job strain assessment easier and quicker than ever, Rasch rating scale model was used to analyze data from 1,644 hospital employees who enrolled in 2008 for a job strain survey. We determined whether the 22-item Job Content Questionnaire (JCQ could evaluate job strain of individual employees in work sites. The respective item responding to specific groups' occupational hazards causing job stress was investigated by using skewness coefficient with its 95% CI through item-by-item analyses. Results Each of those 22 items on the questionnaire was examined to have five factors. The prevalence rate of Chinese hospital workers with high job strain was 16.5%. Conclusions Graphical representations of four quadrants, item-by-item bar chart plots and skewness 95% CI comparison generated in Excel can help employers and consultants of an organization focusing on a small number of key areas of concern for each worker in job strain.

  12. A probabilistic approach to quantitatively assess the inhalation risk for airborne endotoxin in cotton textile workers

    Energy Technology Data Exchange (ETDEWEB)

    Liao, Vivian Hsiu-Chuan, E-mail: vivianliao@ntu.edu.tw [Department of Bioenvironmental Systems Engineering, National Taiwan University, 1 Roosevelt Road, Sec. 4, Taipei 106, Taiwan (China); Chou, Wei-Chun; Chio, Chia-Pin; Ju, Yun-Ru; Liao, Chung-Min [Department of Bioenvironmental Systems Engineering, National Taiwan University, 1 Roosevelt Road, Sec. 4, Taipei 106, Taiwan (China)

    2010-05-15

    Endotoxin, a component of gram-negative bacterial cell walls, is a proinflammatory agent that induces local and systemic inflammatory responses in normal subjects which can contribute to the risk of developing asthma and chronic obstructive lung diseases. A probabilistic approach linking models of exposure, internal dosimetry, and health effects were carried out to quantitatively assess the potential inhalation risk of airborne endotoxin for workers in cotton textile plants. Combining empirical data and modeling results, we show that the half-maximum effects of the endotoxin dose (ED50) were estimated to be 3.3 x 10{sup 5} (95% confidence interval (CI): 1.9-14.7 x 10{sup 5}) endotoxin units (EU) for the blood C-reactive protein (CRP) concentration, 1.1 x 10{sup 5} (95% CI: 0.6-1.7 x 10{sup 5}) EU for the blood polymorphonuclear neutrophil (PMN) count, and 1.5 x 10{sup 5} (95% CI: 0.4-2.5 x 10{sup 5}) EU for the sputum PMN count. Our study offers a risk-management framework for discussing future establishment of limits for respiratory exposure to airborne endotoxin for workers in cotton textile plants.

  13. Investigation of beryllium/steam interaction

    Energy Technology Data Exchange (ETDEWEB)

    Chekhonadskikh, A.M.; Vurim, A.D.; Vasilyev, Yu.S.; Pivovarov, O.S. [Inst. of Atomic Energy National Nuclear Center of the Republic of Kazakstan Semipalatinsk (Kazakhstan); Shestakov, V.P.; Tazhibayeva, I.L.

    1998-01-01

    In this report program on investigations of beryllium emissivity and transient processes on overheated beryllium surface attacked by water steam to be carried out in IAE NNC RK within Task S81 TT 2096-07-16 FR. The experimental facility design is elaborated in this Report. (author)

  14. Modeling of hydrogen interactions with beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Longhurst, G.R. [Lockheed Martin Idaho Technologies Co., Idaho Falls, ID (United States)

    1998-01-01

    In this paper, improved mathematical models are developed for hydrogen interactions with beryllium. This includes the saturation effect observed for high-flux implantation of ions from plasmas and retention of tritium produced from neutronic transmutations in beryllium. Use of the models developed is justified by showing how they can replicated experimental data using the TMAP4 tritium transport code. (author)

  15. Beryllium chloride-induced oxidative DNA damage and alteration in the expression patterns of DNA repair-related genes.

    Science.gov (United States)

    Attia, Sabry M; Harisa, Gamaleldin I; Hassan, Memy H; Bakheet, Saleh A

    2013-09-01

    Beryllium metal has physical properties that make its use essential for very specific applications, such as medical diagnostics, nuclear/fusion reactors and aerospace applications. Because of the widespread human exposure to beryllium metals and the discrepancy of the genotoxic results in the reported literature, detail assessments of the genetic damage of beryllium are warranted. Mice exposed to beryllium chloride at an oral dose of 23mg/kg for seven consecutive days exhibited a significant increase in the level of DNA-strand breaking and micronuclei formation as detected by a bone marrow standard comet assay and micronucleus test. Whereas slight beryllium chloride-induced oxidative DNA damage was detected following formamidopyrimidine DNA glycosylase digestion, digestion with endonuclease III resulted in considerable increases in oxidative DNA damage after the 11.5 and 23mg/kg/day treatment as detected by enzyme-modified comet assays. Increased 8-hydroxydeoxyguanosine was also directly correlated with increased bone marrow micronuclei formation and DNA strand breaks, which further confirm the involvement of oxidative stress in the induction of bone marrow genetic damage after exposure to beryllium chloride. Gene expression analysis on the bone marrow cells from beryllium chloride-exposed mice showed significant alterations in genes associated with DNA damage repair. Therefore, beryllium chloride may cause genetic damage to bone marrow cells due to the oxidative stress and the induced unrepaired DNA damage is probably due to the down-regulation in the expression of DNA repair genes, which may lead to genotoxicity and eventually cause carcinogenicity.

  16. BERYLLIUM MEASUREMENT IN COMMERCIALLY AVAILABLE WET WIPES

    Energy Technology Data Exchange (ETDEWEB)

    Youmans-Mcdonald, L.

    2011-02-18

    Analysis for beryllium by fluorescence is now an established method which is used in many government-run laboratories and commercial facilities. This study investigates the use of this technique using commercially available wet wipes. The fluorescence method is widely documented and has been approved as a standard test method by ASTM International and the National Institute for Occupational Safety and Health (NIOSH). The procedure involves dissolution of samples in aqueous ammonium bifluoride solution and then adding a small aliquot to a basic hydroxybenzoquinoline sulfonate fluorescent dye (Berylliant{trademark} Inc. Detection Solution Part No. CH-2) , and measuring the fluorescence. This method is specific to beryllium. This work explores the use of three different commercial wipes spiked with beryllium, as beryllium acetate or as beryllium oxide and subsequent analysis by optical fluorescence. The effect of possible interfering metals such as Fe, Ti and Pu in the wipe medium is also examined.

  17. Beryllium for fusion application - recent results

    Science.gov (United States)

    Khomutov, A.; Barabash, V.; Chakin, V.; Chernov, V.; Davydov, D.; Gorokhov, V.; Kawamura, H.; Kolbasov, B.; Kupriyanov, I.; Longhurst, G.; Scaffidi-Argentina, F.; Shestakov, V.

    2002-12-01

    The main issues for the application of beryllium in fusion reactors are analyzed taking into account the latest results since the ICFRM-9 (Colorado, USA, October 1999) and presented at 5th IEA Be Workshop (10-12 October 2001, Moscow Russia). Considerable progress has been made recently in understanding the problems connected with the selection of the beryllium grades for different applications, characterization of the beryllium at relevant operational conditions (irradiation effects, thermal fatigue, etc.), and development of required manufacturing technologies. The key remaining problems related to the application of beryllium as an armour in near-term fusion reactors (e.g. ITER) are discussed. The features of the application of beryllium and beryllides as a neutron multiplier in the breeder blanket for power reactors (e.g. DEMO) in pebble-bed form are described.

  18. Application of handheld devices to field research among underserved construction worker populations: a workplace health assessment pilot study

    Directory of Open Access Journals (Sweden)

    Fleming Lora E

    2011-04-01

    Full Text Available Abstract Background Novel low-cost approaches for conducting rapid health assessments and health promotion interventions among underserved worker groups are needed. Recruitment and participation of construction workers is particularly challenging due to their often transient periods of work at any one construction site, and their limited time during work to participate in such studies. In the present methodology report, we discuss the experience, advantages and disadvantages of using touch screen handheld devices for the collection of field data from a largely underserved worker population. Methods In March 2010, a workplace-centered pilot study to examine the feasibility of using a handheld personal device for the rapid health assessment of construction workers in two South Florida Construction sites was undertaken. A 45-item survey instrument, including health-related questions on tobacco exposure, workplace safety practices, musculoskeletal disorders and health symptoms, was programmed onto Apple iPod Touch® devices. Language sensitive (English and Spanish recruitment scripts, verbal consent forms, and survey questions were all preloaded onto the handheld devices. The experience (time to survey administration and capital cost of the handheld administration method was recorded and compared to approaches available in the extant literature. Results Construction workers were very receptive to the recruitment, interview and assessment processes conducted through the handheld devices. Some workers even welcomed the opportunity to complete the questionnaire themselves using the touch screen handheld device. A list of advantages and disadvantages emerged from this experience that may be useful in the rapid health assessment of underserved populations working in a variety of environmental and occupational health settings. Conclusions Handheld devices, which are relatively inexpensive, minimize survey response error, and allow for easy storage of data

  19. Biological exposure assessment to tetrachloroethylene for workers in the dry cleaning industry

    Directory of Open Access Journals (Sweden)

    Ashley David L

    2008-04-01

    Full Text Available Abstract Background The purpose of this study was to assess the feasibility of conducting biological tetrachloroethylene (perchloroethylene, PCE exposure assessments of dry cleaning employees in conjunction with evaluation of possible PCE health effects. Methods Eighteen women from four dry cleaning facilities in southwestern Ohio were monitored in a pilot study of workers with PCE exposure. Personal breathing zone samples were collected from each employee on two consecutive work days. Biological monitoring included a single measurement of PCE in blood and multiple measurements of pre- and post-shift PCE in exhaled breath and trichloroacetic acid (TCA in urine. Results Post-shift PCE in exhaled breath gradually increased throughout the work week. Statistically significant correlations were observed among the exposure indices. Decreases in PCE in exhaled breath and TCA in urine were observed after two days without exposure to PCE. A mixed-effects model identified statistically significant associations between PCE in exhaled breath and airborne PCE time weighted average (TWA after adjusting for a random participant effect and fixed effects of time and body mass index. Conclusion Although comprehensive, our sampling strategy was challenging to implement due to fluctuating work schedules and the number (pre- and post-shift on three consecutive days and multiplicity (air, blood, exhaled breath, and urine of samples collected. PCE in blood is the preferred biological index to monitor exposures, but may make recruitment difficult. PCE TWA sampling is an appropriate surrogate, although more field intensive. Repeated measures of exposure and mixed-effects modeling may be required for future studies due to high within-subject variability. Workers should be monitored over a long enough period of time to allow the use of a lag term.

  20. Office workers' objectively assessed total and prolonged sitting time: Individual-level correlates and worksite variations.

    Science.gov (United States)

    Hadgraft, Nyssa T; Healy, Genevieve N; Owen, Neville; Winkler, Elisabeth A H; Lynch, Brigid M; Sethi, Parneet; Eakin, Elizabeth G; Moodie, Marj; LaMontagne, Anthony D; Wiesner, Glen; Willenberg, Lisa; Dunstan, David W

    2016-12-01

    Sedentary behavior is highly prevalent in office-based workplaces; however, few studies have assessed the attributes associated with this health risk factor in the workplace setting. This study aimed to identify the correlates of office workers' objectively-assessed total and prolonged (≥ 30 min bouts) workplace sitting time. Participants were 231 Australian office workers recruited from 14 sites of a single government employer in 2012-13. Potential socio-demographic, work-related, health-related and cognitive-social correlates were measured through a self-administered survey and anthropometric measurements. Associations with total and prolonged workplace sitting time (measured with the activPAL3) were tested using linear mixed models. Worksites varied significantly in total workplace sitting time (overall mean [SD]: 79% [10%] of work hours) and prolonged workplace sitting time (42% [19%]), after adjusting for socio-demographic and work-related characteristics. Organisational tenure of 3-5 years (compared to tenure > 5 years) was associated with more time spent in total and prolonged workplace sitting time, while having a BMI categorised as obese (compared to a healthy BMI) was associated with less time spent in total and prolonged workplace sitting time. Significant variations in sitting time were observed across different worksites of the same employer and the variation remained after adjusting for individual-level factors. Only BMI and organisational tenure were identified as correlates of total and prolonged workplace sitting time. Additional studies are needed to confirm the present findings across diverse organisations and occupations. PMID:27413681

  1. Postirradiation examination of beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Gelles, D.S. [Pacific Northwest National Lab., Richland, WA (United States)

    1998-03-01

    Postirradiation examinations of COBRA-1A beryllium pebbles irradiated in the EBR-II fast reactor at neutron fluences which generated 2700--3700 appm helium have been performed. Measurements included density change, optical microscopy, scanning electron microscopy, and transmission electron microscopy. The major change in microstructure is development of unusually shaped helium bubbles forming as highly non-equiaxed thin platelet-like cavities on the basal plane. Measurement of the swelling due to cavity formation was in good agreement with density change measurements.

  2. Technical issues for beryllium use in fusion blanket applications

    International Nuclear Information System (INIS)

    Beryllium is an excellent non-fissioning neutron multiplier for fusion breeder and fusion electric blanket applications. This report is a compilation of information related to the use of beryllium with primary emphasis on the fusion breeder application. Beryllium resources, production, fabrication, properties, radiation damage and activation are discussed. A new theoretical model for beryllium swelling is presented

  3. 20 CFR 30.615 - What type of tort suits filed against beryllium vendors or atomic weapons employers may...

    Science.gov (United States)

    2010-04-01

    ... Part B of EEOICPA? 30.615 Section 30.615 Employees' Benefits OFFICE OF WORKERS' COMPENSATION PROGRAMS... certain claimants from receiving benefits under Part B of EEOICPA? (a) A tort suit (other than an... Part B employee's employment-related exposure to beryllium or radiation, filed against a...

  4. Fluorimetric method for determination of Beryllium

    International Nuclear Information System (INIS)

    The old fluorimetric method for the determination of Beryllium, based essentially on the fluorescence of the Beryllium-Morine complex in a strongly alkaline solution, is still competitive and stands the comparison with more modern methods or at least three reasons: in the presence of solid or gaseous samples (powders), the times necessary to finalize an analytic determination are comparable since the stage of the process which lasts the longest is the mineralization of the solid particles containing Beryllium, the cost of a good fluorimeter is by far Inferior to the cost, e. g., of an Emission Spectrophotometer provided with ICP torch and magnets for exploiting the Zeeman effect and of an Atomic absorption Spectrophotometer provided with Graphite furnace; it is possible to determine, fluorimetrically, rather small Beryllium levels (about 30 ng of Beryllium/sample), this potentiality is more than sufficient to guarantee the respect of all the work safety and hygiene rules now in force. The study which is the subject of this publication is designed to the analysis procedure which allows one to reach good results in the determination of Beryllium, chiefly through the control and measurement of the interference effect due to the presence of some metals which might accompany the environmental samples of workshops and laboratories where Beryllium is handled, either at the pure state or in its alloys. The results obtained satisfactorily point out the merits and limits of this analytic procedure

  5. Correspondence in Stakeholder Assessment of Health, Work Capacity and Sick Leave in Workers with Comorbid Subjective Health Complaints? A Video Vignette Study.

    Science.gov (United States)

    Maeland, Silje; Magnussen, Liv Heide; Eriksen, Hege R; Werner, Erik L; Helle-Valle, Anna; Hensing, Gunnel

    2016-09-01

    Purpose The purpose of this study is to test if there is correspondence in stakeholders' assessments of health, work capacity and sickness certification in four workers with comorbid subjective health complaints based on video vignettes. Methods A cross sectional survey among stakeholders (N = 514) in Norway in 2009/2010. Logistic regression and multinomial logistic regression was used to obtain the estimated probability of stakeholders choosing 100 % sick leave, partial sick leave or work and the estimation of odds ratio of stakeholder assessment compared to the other stakeholders for the individual worker. Results The supervisors were less likely to assess poor health and reduced work capacity, and more likely to suggest partial sick leave and full time work compared to the GPs for worker 1. The public was less likely to assess comorbidity and reduced work capacity, and 6 and 12 times more likely to suggest partial sick leave and full time work compared to the GPs for worker 1. Stakeholders generally agreed in their assessments of workers 2 and 3. The public was more likely to assess poor health, comorbidity and reduced work capacity, and the supervisors more likely to assess comorbidity and reduced work capacity, compared to the GPs for worker 4. Compared to the GPs, all other stakeholders were less likely to suggest full time work for this worker. Conclusions Our results seem to suggest that stakeholders have divergent assessments of complaints, health, work capacity, and sickness certification in workers with comorbid subjective health complaints. PMID:26615412

  6. Preliminary proposal for a beryllium technology program for fusion applications

    International Nuclear Information System (INIS)

    The program was designed to provide the answers to the critical issues of beryllium technology needed in fusion blanket designs. The four tasks are as follows: (1) Beryllium property measurements needed for fusion data base. (2) Beryllium stress relaxation and creep measurements for lifetime modelling calculations. (3) Simplified recycle technique development for irradiated beryllium. (4) Beryllium neutron multiplier measurements using manganese bath absolute calibration techniques

  7. Recommended design correlations for S-65 beryllium

    International Nuclear Information System (INIS)

    The properties of tritium and helium behavior in irradiated beryllium are reviewed, along with the thermal-mechanical properties needed for ITER design analysis. Correlations are developed to describe the performance of beryllium in a fusion reactor environment. While this paper focuses on the use of beryllium as a plasma-facing component (PFC) material, the correlations presented here can also be used to describe the performance of beryllium as a neutron multiplier for a tritium breeding blanket. The performance properties for beryllium are subdivided into two categories: properties which do not change with irradiation damage to the bulk of the material; and properties which are degraded by neutron irradiation. The irradiation-independent properties described within are: thermal conductivity, specific heat capacity, thermal expansion, and elastic constants. Irradiation-dependent properties include: yield strength, ultimate tensile strength, plastic tangent modulus, uniform and total tensile elongation, thermal and irradiation-induced creep strength, He-induced swelling and tritium retention/release. The approach taken in developing properties correlations is to describe the behavior of dense, pressed S-65 beryllium -- the material chosen for ITER PFC application -- as a function of temperature. As there are essentially no data on the performance of porous and/or irradiated S-65 beryllium, the degradation of properties with as-fabricated porosity and irradiation are determined from the broad data base on S-200F, as well as other types and grades, and applied to S-65 beryllium by scaling factors. The resulting correlations can be used for Be produced by vacuum hot pressing (VHP) and cold-pressing (CP)/sintering(S)/hot-isostatic-pressing (HIP). The performance of plasma-sprayed beryllium is discussed but not quantified

  8. Recommended design correlations for S-65 beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Billone, M.C. [Argonne National Lab., IL (United States)

    1995-09-01

    The properties of tritium and helium behavior in irradiated beryllium are reviewed, along with the thermal-mechanical properties needed for ITER design analysis. Correlations are developed to describe the performance of beryllium in a fusion reactor environment. While this paper focuses on the use of beryllium as a plasma-facing component (PFC) material, the correlations presented here can also be used to describe the performance of beryllium as a neutron multiplier for a tritium breeding blanket. The performance properties for beryllium are subdivided into two categories: properties which do not change with irradiation damage to the bulk of the material; and properties which are degraded by neutron irradiation. The irradiation-independent properties described within are: thermal conductivity, specific heat capacity, thermal expansion, and elastic constants. Irradiation-dependent properties include: yield strength, ultimate tensile strength, plastic tangent modulus, uniform and total tensile elongation, thermal and irradiation-induced creep strength, He-induced swelling and tritium retention/release. The approach taken in developing properties correlations is to describe the behavior of dense, pressed S-65 beryllium -- the material chosen for ITER PFC application -- as a function of temperature. As there are essentially no data on the performance of porous and/or irradiated S-65 beryllium, the degradation of properties with as-fabricated porosity and irradiation are determined from the broad data base on S-200F, as well as other types and grades, and applied to S-65 beryllium by scaling factors. The resulting correlations can be used for Be produced by vacuum hot pressing (VHP) and cold-pressing (CP)/sintering(S)/hot-isostatic-pressing (HIP). The performance of plasma-sprayed beryllium is discussed but not quantified.

  9. [ASSESSMENT OF EXTREME FACTORS OF SHIFT WORK IN ARCTIC CONDITIONS BY WORKERS WITH DIFFERENT REGULATORY PROCESSES].

    Science.gov (United States)

    Korneeva, Ya A; Simonova, N N

    2016-01-01

    A man working on a shift basis in the Arctic, every day is under the influence of various extreme factors which are inevitable for oil and gas indudtry. To adapt to shift work employees use various resources of the individual. The purpose of research is the determination of personal resources of shift workers to overcome the adverse factors of the environment in the Arctic. The study involved 191 builder of main gas pipelines, working in shifts in the Tyumen region (the length of the shift 52 days of arrival) at the age of 23 to 59 (mean age 34.9 ± 8.1) years. Methods: psychological testing, questioning, observation, descriptive statistics, discriminant step by step analysis. There was revealed the correlation between the subjective assessment of the majority of adverse climatic factors in the regulatory process "assessment of results"; production factors--regulatory processes such as flexibility, autonomy, simulation, and the general level of self-regulation; social factors are more associated with the severity of such regulatory processes, flexibility and evaluation of results. PMID:27430072

  10. Lung cinescintigraphy in the dynamic assessment of ventilation and mucociliary clearance of asbestos cement workers.

    OpenAIRE

    Di Lorenzo, L; Mele, M; Pegorari, M M; Fratello, A; Zocchetti, C; Capozzi, D.

    1996-01-01

    OBJECTIVES: To verify in vivo whether lung cinescintigraphy confirms the effect of asbestos on the patency of the smallest airways and on the efficiency of mucociliary clearance in asbestos cement workers. METHODS: 39 male subjects were examined: 30 asbestos cement workers and nine workers never exposed to occupational respiratory irritants. All subjects had a chest radiograph (International Labour Organisation (ILO) 1980); standard questionnaire on chronic bronchitis; spirometry; arterial bl...

  11. Beryllium Concentrations at European Workplaces: Comparison of ‘Total’ and Inhalable Particulate Measurements

    OpenAIRE

    Kock, Heiko; Civic, Terence; Koch, Wolfgang

    2015-01-01

    A field study was carried out in order to derive a factor for the conversion of historic worker exposure data on airborne beryllium (Be) obtained by sampling according to the 37-mm closed faced filter cassette (CFC) ‘total’ particulate method into exposure concentration values to be expected when sampling using the ‘Gesamtstaubprobenahmesystem’ (GSP) inhalable sampling convention. Workplaces selected to represent the different copper Be work processing operations that typically occur in Germa...

  12. Assessment of psychosocial risks faced by workers in Almería-type greenhouses, using the Mini Psychosocial Factor method.

    Science.gov (United States)

    Montoya-García, M E; Callejón-Ferre, A J; Pérez-Alonso, J; Sánchez-Hermosilla, J

    2013-03-01

    This work reports the use of the Mini Psychosocial Factor (MPF) method for assessing the psychosocial risks faced by agricultural workers in the greenhouses of Almería (Spain) with the aim of improving their health. The variables Rhythm, Mobbing, Relationships, Health, Recognition, Autonomy, Emotional Involvement, Support, Compensation, Control, Demands, and Mental Load were recorded using a pre-validated questionnaire containing 15 questions. The sex, age, and nationality of the respondents (n = 310) were also recorded, as were the type of greenhouse in which each worked, the size of the greenhouse, and the crop grown. The results showed psychosocial risks to exist for the workers. Multiple correspondence analysis, however, showed that moderate risks can be offset by new prevention programmes that improve Spanish legislation in terms of workers' salaries, worker-employer social days, work timetables to facilitate family life, and training courses. This could improve the work environment and health of Almería's greenhouse workers as well as their productivity. PMID:22981469

  13. Impact of HFIR LEU Conversion on Beryllium Reflector Degradation Factors

    Energy Technology Data Exchange (ETDEWEB)

    Ilas, Dan [ORNL

    2013-10-01

    An assessment of the impact of low enriched uranium (LEU) conversion on the factors that may cause the degradation of the beryllium reflector is performed for the High Flux Isotope Reactor (HFIR). The computational methods, models, and tools, comparisons with previous work, along with the results obtained are documented and discussed in this report. The report documents the results for the gas and neutronic poison production, and the heating in the beryllium reflector for both the highly enriched uranium (HEU) and LEU HFIR configurations, and discusses the impact that the conversion to LEU may have on these quantities. A time-averaging procedure was developed to calculate the isotopic (gas and poisons) production in reflector. The sensitivity of this approach to different approximations is gauged and documented. The results show that the gas is produced in the beryllium reflector at a total rate of 0.304 g/cycle for the HEU configuration; this rate increases by ~12% for the LEU case. The total tritium production rate in reflector is 0.098 g/cycle for the HEU core and approximately 11% higher for the LEU core. A significant increase (up to ~25%) in the neutronic poisons production in the reflector during the operation cycles is observed for the LEU core, compared to the HEU case, for regions close to the core s horizontal midplane. The poisoning level of the reflector may increase by more than two orders of magnitude during long periods of downtime. The heating rate in the reflector is estimated to be approximately 20% lower for the LEU core than for the HEU core. The decrease is due to a significantly lower contribution of the heating produced by the gamma radiation for the LEU core. Both the isotopic (gas and neutronic poisons) production and the heating rates are spatially non-uniform throughout the beryllium reflector volume. The maximum values typically occur in the removable reflector and close to the midplane.

  14. Assessing the Factors Associated with Sexual Harassment among Young Female Migrant Workers in Nepal

    Science.gov (United States)

    Puri, Mahesh; Cleland, John

    2007-01-01

    This article explores the extent of, and factors associated with, sexual harassment of young female migrant workers in the carpet and garment factories in Kathmandu Valley. Information is drawn from a survey of 550 female workers aged 14 to 19 and 12 in-depth case histories. Bivariate and multivariate techniques were applied to identify the…

  15. Assessing the Impact of Ongoing National Terror: Social Workers in Israel

    Science.gov (United States)

    Ron, Pnina; Shamai, Michal

    2011-01-01

    The main goal of this study was to explore the connections between social workers' personal and professional exposure to national terror in Israel and their professional and personal distress experienced due to ongoing terror attacks. Data were collected from 406 social workers from Israel who worked in agencies that provide help to victims of…

  16. Chronic Beryllium Disease Prevention Program Report

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S

    2012-03-29

    This document describes how Lawrence Livermore National Laboratory (LLNL) meets the requirements and management practices of federal regulation 10 CFR 850, 'Chronic Beryllium Disease Prevention Program (CBDPP).' This revision of the LLNL CBDPP incorporates clarification and editorial changes based on lessons learned from employee discussions, observations and reviews of Department of Energy (DOE) Complex and commercial industry beryllium (Be) safety programs. The information is used to strengthen beryllium safety practices at LLNL, particularly in the areas of: (1) Management of small parts and components; and (2) Communication of program status to employees. Future changes to LLNL beryllium activities and on-going operating experience will be incorporated into the program as described in Section S, 'Performance Feedback.'

  17. Lithium-Beryllium-Boron : Origin and Evolution

    OpenAIRE

    Vangioni-Flam, Elisabeth; Casse, Michel; Audouze, Jean

    1999-01-01

    The origin and evolution of Lithium-Beryllium-Boron is a crossing point between different astrophysical fields : optical and gamma spectroscopy, non thermal nucleosynthesis, Big Bang and stellar nucleosynthesis and finally galactic evolution. We describe the production and the evolution of Lithium-Beryllium-Boron from Big Bang up to now through the interaction of the Standard Galactic Cosmic Rays with the interstellar medium, supernova neutrino spallation and a low energy component related to...

  18. Assessment of oral hygiene habits, oral hygiene practices and tooth wear among fertilizer factory workers of Northern India: A Cross sectional study

    OpenAIRE

    Vivek V Gupta; Asawa, Kailash; Bhat, Nagesh; Tak, Mridula; Bapat, Salil; Chaturvedi, Pulkit; Philip George, Pradeep; Chitkara, Neha; Patel, Maulikkumar Natubhai; Shinde, Kushal; Sidhu, Prabhjot Kaur

    2015-01-01

    Background The association between oral hygiene habits & practices and severity of tooth wear lesion varies from community to community and also from occupation to occupation. The present study was conducted with to assess oral hygiene habits & practices and tooth wear among fertilizer factory workers of Punjab, India. Material and Methods A descriptive cross sectional survey was conducted among 965 male workers who were aged between 19–58 years, who were the workers of fertilizers factory of...

  19. Tritium release from neutron irradiated beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Scaffidi-Argentina, F.; Werle, H. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reactortechnik

    1998-01-01

    One of the most important open issues related to beryllium for fusion applications refers to the kinetics of the tritium release as a function of neutron fluence and temperature. The EXOTIC-7 as well as the `Beryllium` experiments carried out in the HFR reactor in Petten are considered as the most detailed and significant tests for investigating the beryllium response under neutron irradiation. This paper reviews the present status of beryllium post-irradiation examinations performed at the Forschungszentrum Karlsruhe with samples from the above mentioned irradiation experiments, trying to elucidate the tritium release controlling processes. In agreement with previous studies it has been found that release starts at about 500-550degC and achieves a maximum at about 700-750degC. The observed release at about 500-550degC is probably due to tritium escaping from chemical traps, while the maximum release at about 700-750degC is due to tritium escaping from physical traps. The consequences of a direct contact between beryllium and ceramics during irradiation, causing tritium implanting in a surface layer of beryllium up to a depth of about 40 mm and leading to an additional inventory which is usually several times larger than the neutron-produced one, are also presented and the effects on the tritium release are discussed. (author)

  20. Assessment of Fidelity in Interventions to Improve Hand Hygiene of Healthcare Workers: A Systematic Review.

    Science.gov (United States)

    Musuuza, Jackson S; Barker, Anna; Ngam, Caitlyn; Vellardita, Lia; Safdar, Nasia

    2016-05-01

    OBJECTIVE Compliance with hand hygiene in healthcare workers is fundamental to infection prevention yet remains a challenge to sustain. We examined fidelity reporting in interventions to improve hand hygiene compliance, and we assessed 5 measures of intervention fidelity: (1) adherence, (2) exposure or dose, (3) quality of intervention delivery, (4) participant responsiveness, and (5) program differentiation. DESIGN Systematic review METHODS A librarian performed searches of the literature in PubMed, Cumulative Index to Nursing and Allied Health (CINAHL), Cochrane Library, and Web of Science of material published prior to June 19, 2015. The review protocol was registered in PROSPERO International Prospective Register of Systematic Reviews, and assessment of study quality was conducted for each study reviewed. RESULTS A total of 100 studies met the inclusion criteria. Only 8 of these 100 studies reported all 5 measures of intervention fidelity. In addition, 39 of 100 (39%) failed to include at least 3 fidelity measures; 20 of 100 (20%) failed to include 4 measures; 17 of 100 (17%) failed to include 2 measures, while 16 of 100 (16%) of the studies failed to include at least 1 measure of fidelity. Participant responsiveness and adherence to the intervention were the most frequently unreported fidelity measures, while quality of the delivery was the most frequently reported measure. CONCLUSIONS Almost all hand hygiene intervention studies failed to report at least 1 fidelity measurement. To facilitate replication and effective implementation, reporting fidelity should be standard practice when describing results of complex behavioral interventions such as hand hygiene. Infect Control Hosp Epidemiol 2016;37:567-575. PMID:26861117

  1. Assessing the Impact of Peer Educator Outreach on the Likelihood and Acceleration of Clinic Utilization among Sex Workers

    Science.gov (United States)

    Krishnamurthy, Parthasarathy; Hui, Sam K.; Shivkumar, Narayanan; Gowda, Chandrasekhar; Pushpalatha, R.

    2016-01-01

    Objective Peer-led outreach is a critical element of HIV and STI-reduction interventions aimed at sex workers. We study the association between peer-led outreach to sex workers and the time to utilize health facilities for timely STI syndromic-detection and treatment. Using data on the timing of peer-outreach interventions and clinic visits, we utilize an Extended Cox model to assess whether peer educator outreach intensity is associated with accelerated clinic utilization among sex workers. Methods Our data comes from 2705 female sex workers registered into Pragati, a women-in-sex-work outreach program, and followed from 2008 through 2012. We analyze this data using an Extended Cox model with the density of peer educator visits in a 30-day rolling window as the key predictor, while controlling for the sex workers’ age, client volume, location of sex work, and education level. The principal outcome of interest is the timing of the first voluntary clinic utilization. Results More frequent peer visit is associated with earlier first clinic visit (HR: 1.83, 95% CI, 1.75–1.91, p < .001). In addition, 18% of all syndrome-based STI detected come from clinic visits in which the sex worker reports no symptoms, underscoring the importance of inducing clinic visits in the detection of STI. Additional models to test the robustness of these findings indicate consistent beneficial effect of peer educator outreach. Conclusions Peer outreach density is associated with increased likelihood of–and shortened duration to–clinic utilization among female sex workers, suggesting potential staff resourcing implications. Given the observational nature of our study, however, these findings should be interpreted as an association rather than as a causal relationship. PMID:27467124

  2. Sanitary-hygienic and ecological aspects of beryllium production

    Energy Technology Data Exchange (ETDEWEB)

    Dvinskykh, E.M.; Savchuk, V.V.; Sidorov, V.L.; Slobodin, D.B.; Tuzov, Y.V. [Ulba Metallurgical Plant, Ust-Kamenogorsk (Kazakhstan)

    1998-01-01

    The Report describes An organization of sanitary-hygienic and ecological control of beryllium production at Ulba metallurgical plant. It involves: (1) the consideration of main methods for protection of beryllium production personnel from unhealthy effect of beryllium, (2) main kinds of filters, used in gas purification systems at different process areas, (3) data on beryllium monitoring in water, soil, on equipment. This Report also outlines problems connected with designing devices for a rapid analysis of beryllium in air as well as problems of beryllium production on ecological situation in the town. (author)

  3. Uncertainty in the estimation of benzene risks: application of an uncertainty taxonomy to risk assessments based on an epidemiology study of rubber hydrochloride workers.

    OpenAIRE

    Byrd, D M; Barfield, E T

    1989-01-01

    This paper reviews 14 risk assessments that use the data from descriptions by Rinsky, Young, and co-workers of benzene-associated leukemias among a group of rubber hydrochloride workers in Ohio. The leukemogenic risks of benzene estimated in these assessments differ. The assessors use different assumptions (parameters, confounding factors, or formulas), which account for the differences in risk. The purpose of the review is to determine whether the major source of uncertainty in assessments o...

  4. Knowledge and communication needs assessment of community health workers in a developing country: a qualitative study

    Directory of Open Access Journals (Sweden)

    Hafeez Assad

    2009-07-01

    Full Text Available Abstract Background Primary health care is a set of health services that can meet the needs of the developing world. Community health workers act as a bridge between health system and community in providing this care. Appropriate knowledge and communication skills of the workers are key to their confidence and elementary for the success of the system. We conducted this study to document the perceptions of these workers on their knowledge and communication needs, image building through mass media and mechanisms for continued education. Methods Focus group discussions were held with health workers and their supervisors belonging to all the four provinces of the country and the Azad Jammu & Kashmir region. Self-response questionnaires were also used to obtain information on questions regarding their continued education. Results About four fifths of the respondents described their communication skills as moderately sufficient and wanted improvement. Knowledge on emerging health issues was insufficient and the respondents showed willingness to participate in their continued education. Media campaigns were successful in building the image of health workers as a credible source of health information. Conclusion A continued process should be ensured to provide opportunities to health workers to update their knowledge, sharpen communication skills and bring credibility to their persona as health educators.

  5. Assessment of knowledge and perception regarding male sterilization (Non-Scalpel Vasectomy among community health workers in Jharkhand, India

    Directory of Open Access Journals (Sweden)

    Swati Mahapatra

    2014-12-01

    Full Text Available Introduction: In India, community health workers are the main source of information for family planning services and male population want to interact and discuss with them to clear their doubts about male oriented family planning methods. Objective: The objective of the study was to assess the knowledge and perception of community health workers regarding the modern male sterilization method. Methodology: This was a cross-sectional study conducted in Simdega district of Jharkhand. The target population was the community health workers and randomly selected from four randomly selected from blocks out of total seven in the district. A self-administered quantitative questionnaire was used for data collection comprising questions related to knowledge and perception of community health workers about modern male sterilization method. Results: 43% CHWs didn’t know that this method is different from traditional male sterilization method and around 62% thought man’s sexual performance get affected after NSV and 77% did not have any idea about time required to resume normal work. Conclusions: The poor knowledge and wrong perception could be one of the main reasons for poor male participation in family planning process in India.

  6. Beryllium. Health hazards and their control. Pt. 2

    International Nuclear Information System (INIS)

    In this work (continuation of 'Beryllium' series) health hazards, toxic effects, limits of permissible atmospheric contamination and safe exposure to beryllium are described. Guidelines to the design, control operations and hygienic precautions of the working facilities are given. (Author)

  7. Mechanical performance of irradiated beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Scaffidi-Argentina, F.; Dalle-Donne, M.; Werle, H. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reaktortechnik

    1998-01-01

    For the Helium Cooled Pebble Bed (HCPB) Blanket, which is one of the two reference concepts studied within the European Fusion Technology Programme, the neutron multiplier consists of a mixed bed of about 2 and 0.1-0.2 mm diameter beryllium pebbles. Beryllium has no structural function in the blanket, however microstructural and mechanical properties are important, as they might influence the material behavior under neutron irradiation. The EXOTIC-7 as well as the `Beryllium` experiments carried out in the HFR reactor in Petten are considered as the most detailed and significant tests for investigating it. This paper reviews the present status of beryllium post-irradiation examinations performed at the Forschungszentrum Karlsruhe with samples from these irradiation experiments, emphasizing the effects of irradiation of essential material properties and trying to elucidate the processes controlling the property changes. The microstructure, the porosity distribution, the impurity content, the behavior under compression loads and the compatibility of the beryllium pebbles with lithium orthosilicate (Li{sub 4}SiO{sub 4}) during the in-pile irradiation are presented and critically discussed. Qualitative information on ductility and creep obtained by hardness-type measurements are also supplied. (author)

  8. Time-lapse cinematographic analysis of beryllium--lung fibroblast interactions.

    Science.gov (United States)

    Absher, M; Sylwester, D; Hart, B A

    1983-02-01

    The proliferative response to beryllium chloride of cells in a population of human lung fibroblasts was quantitatively assessed using time-lapse cinematography. A dose of 0.02 microgram Be/ml, known to decrease the growth rate of fibroblasts, affects an estimated 75% of the cells in the population, increasing their interdivision time (IDT) by approximately 5 hr. The differences in mean 1n(IDT) between treated and control cells were essentially constant for comparable culture sizes ranging from 25 to 250 cells. There was no correlation between mother and daughter cell IDTs in control or treated culture at any culture size. IDTs of sister pairs were highly correlated in control cultures at selected culture sizes while sister pair IDTs of treated cultures were not. The data suggest that while beryllium alters the IDT of fibroblasts, an effect not related to culture size, any given cell affected by beryllium does not impart effects of the mineral to its progeny.

  9. Assessing the Ultraviolet Exposure Level in Welding Workers of Sar-Cheshmeh Copper Complex

    Directory of Open Access Journals (Sweden)

    Javad Vatani

    2013-04-01

    Full Text Available Background: Because of being exposed to a wide range of ultraviolet radiations, welders are prone to eye and skin diseases. This study aims at determining the ultraviolet exposure level in welding workers of Sar-Cheshmeh Copper Complex.Materials and Methods: This cross-sectional study was conducted in 2010 on all welding workers of the complex using Hagner UV digital radiometer.Results: The mean value for the received ultraviolet radiation level was 0.09±0.045 j2/cm2. The level of UV exposure was significantly different (p=0.001 for the welders working in different units of the complex. The mineworkers received the highest level of radiation (0.14 j2/cm2.Conclusion: In this study, the ultraviolet exposure of welding workers is below the allowable threshold limit for UV radiation.

  10. A NEAR REAL-TIME BERYLLIUM MONITOR WITH CAM AND WIPE ANALYSIS CAPABILITIES

    Energy Technology Data Exchange (ETDEWEB)

    D.T. Kendrick; Steven Saggese

    2002-12-01

    Science & Engineering Associates, Inc. (SEA), under contract No. DE-AC26-00NT40768, was tasked by the US Department of Energy--National Energy Technology Laboratory to develop and test a near real-time beryllium monitor for airborne and surface measurements. Recent public awareness of the health risks associated with exposure to beryllium has underscored the need for better, faster beryllium monitoring capabilities within the DOE. A near real-time beryllium monitor will offer significant improvements over the baseline monitoring technology currently in use. Whereas the baseline technology relies upon collecting an air sample on a filter and the subsequent analysis of the filter by an analytical laboratory, this effort developed a monitor that offers near real-time measurement results while work is in progress. Since the baseline typically only offers after-the-fact documentation of exposure levels, the near real-time capability provides a significant increase in worker protection. The beryllium monitor developed utilizes laser induced breakdown spectroscopy, or LIBS as the fundamental measurement technology. LIBS has been used in a variety of laboratory and field based instrumentation to provide real-time, and near-real-time elemental analysis capabilities. LIBS is an analytical technique where a pulsed high energy laser beam is focused to a point on the sample to be interrogated. The high energy density produces a small high temperature plasma plume, sometimes called a spark. The conditions within this plasma plume result in the constituent atoms becoming excited and emitting their characteristic optical emissions. The emission light is collected and routed to an optical spectrometer for quantitative spectral analysis. Each element has optical emissions, or lines, of a specific wavelength that can be used to uniquely identify that element. In this application, the intensity of the beryllium emission is used to provide a quantitative measure of the abundance of the

  11. Occupational and non-occupational allergic contact dermatitis from beryllium.

    Science.gov (United States)

    Vilaplana, J; Romaguera, C; Grimalt, F

    1992-05-01

    There are various references to sensitization to beryllium in the literature. Since introducing a patch testing series for patients with suspected sensitization to metals, we have found 3 cases of sensitization to beryllium. Of these 3 cases, we regard the first 2 as having relevant sensitization. Beryllium chloride (1% pet.) was positive in 3 patients and negative in 150 controls.

  12. 75 FR 80734 - Chronic Beryllium Disease Prevention Program

    Science.gov (United States)

    2010-12-23

    ... Beryllium Disease Prevention Program (CBDPP) (63 FR 66940). After considering the comments received, DOE... CFR Part 850 RIN 1992-AA39 Chronic Beryllium Disease Prevention Program AGENCY: Office of Health... beryllium disease prevention program. The Department solicits comment and information on the...

  13. NIOSH field studies team assessment: Worker exposure to aerosolized metal oxide nanoparticles in a semiconductor fabrication facility.

    Science.gov (United States)

    Brenner, Sara A; Neu-Baker, Nicole M; Eastlake, Adrienne C; Beaucham, Catherine C; Geraci, Charles L

    2016-11-01

    The ubiquitous use of engineered nanomaterials-particulate materials measuring approximately 1-100 nanometers (nm) on their smallest axis, intentionally engineered to express novel properties-in semiconductor fabrication poses unique issues for protecting worker health and safety. Use of new substances or substances in a new form may present hazards that have yet to be characterized for their acute or chronic health effects. Uncharacterized or emerging occupational health hazards may exist when there is insufficient validated hazard data available to make a decision on potential hazard and risk to exposed workers under condition of use. To advance the knowledge of potential worker exposure to engineered nanomaterials, the National Institute for Occupational Safety and Health Nanotechnology Field Studies Team conducted an on-site field evaluation in collaboration with on-site researchers at a semiconductor research and development facility on April 18-21, 2011. The Nanomaterial Exposure Assessment Technique (2.0) was used to perform a complete exposure assessment. A combination of filter-based sampling and direct-reading instruments was used to identify, characterize, and quantify the potential for worker inhalation exposure to airborne alumina and amorphous silica nanoparticles associated with th e chemical mechanical planarization wafer polishing process. Engineering controls and work practices were evaluated to characterize tasks that might contribute to potential exposures and to assess existing engineering controls. Metal oxide structures were identified in all sampling areas, as individual nanoparticles and agglomerates ranging in size from 60 nm to >1,000 nm, with varying structure morphology, from long and narrow to compact. Filter-based samples indicated very little aerosolized material in task areas or worker breathing zone. Direct-reading instrument data indicated increased particle counts relative to background in the wastewater treatment area; however

  14. NIOSH Field Studies Team Assessment: Worker Exposure to Aerosolized Metal Oxide Nanoparticles in a Semiconductor Fabrication Facility

    Science.gov (United States)

    Brenner, Sara A.; Neu-Baker, Nicole M.; Eastlake, Adrienne C.; Beaucham, Catherine C.; Geraci, Charles L.

    2016-01-01

    The ubiquitous use of engineered nanomaterials – particulate materials measuring approximately 1–100 nanometers (nm) on their smallest axis, intentionally engineered to express novel properties – in semiconductor fabrication poses unique issues for protecting worker health and safety. Use of new substances or substances in a new form may present hazards that have yet to be characterized for their acute or chronic health effects. Uncharacterized or emerging occupational health hazards may exist when there is insufficient validated hazard data available to make a decision on potential hazard and risk to exposed workers under condition of use. To advance the knowledge of potential worker exposure to engineered nanomaterials, the National Institute for Occupational Safety and Health Nanotechnology Field Studies Team conducted an on-site field evaluation in collaboration with on-site researchers at a semiconductor research and development facility on April 18–21, 2011. The Nanomaterial Exposure Assessment Technique (2.0) was used to perform a complete exposure assessment. A combination of filter-based sampling and direct-reading instruments was used to identify, characterize, and quantify the potential for worker inhalation exposure to airborne alumina and amorphous silica nanoparticles associated with the chemical mechanical planarization wafer polishing process. Engineering controls and work practices were evaluated to characterize tasks that might contribute to potential exposures and to assess existing engineering controls. Metal oxide structures were identified in all sampling areas, as individual nanoparticles and agglomerates ranging in size from 60nm to >1,000nm, with varying structure morphology, from long and narrow to compact. Filter-based samples indicated very little aerosolized material in task areas or worker breathing zone. Direct-reading instrument data indicated increased particle counts relative to background in the wastewater treatment area

  15. Spectrographic determination of impurities in beryllium oxide

    International Nuclear Information System (INIS)

    A method for the spectrographic determination of Al, B, Cd, Co, Cu, Cr, Fe, Mg, NaNi, Si and Zn in nuclear grade beryllium oxide has been developed. The determination of Co, Al, Na and Zn is besed upon a carrier distillation technique. Better results were obtained with 2% Ga2O3 as carrier in beryllium oxide. For the elements B, Cd, Cu, Fe, Cr, Mg, Ni and Si the sample is loaded in a Scribner-Mullin shallow cup electrode, covered with graphite powder and excited in DC arc. The relative standard deviation values for different elements are in the range of 10 to 20%. The method fulfills requirements of precision and sensitivity for specification analysis of nuclear grade beryllium oxide.(Author)

  16. [Effects of beryllium chloride on cultured cells].

    Science.gov (United States)

    Sakaguchi, T; Sakaguchi, S; Nakamura, I; Kagami, M

    1984-05-01

    The effects of beryllium on cultured cells were investigated. Three cell-lines (HeLa-S3, Vero, HEL-R66) were used in these experiments and they were cultured in Eagle's MEM plus 5 or 10% FBS (Fetal Bovine Serum) containing beryllium in various concentrations. HeLa cells or Vero cells were able to grow in the medium with 10 micrograms Be/ml (1.1 mM). On the other hand, the growth of HEL cells were strongly inhibited, even when cultured in the medium with 1 microgram Be/ml (1.1 X 10(-1) mM) and the number of living cells showed markedly low level as compared to that of the control samples cultured in the medium without beryllium. The cytotoxic effects of beryllium on these cells, which were cultured for three days in the medium with beryllium, were observed. None of cytotoxic effects were found on HeLa cells cultured with 0.5 micrograms/ml (5.5 X 10(-2) mM) and on Vero cells cultured with 0.05 micrograms Be/ml (5.5 X 10(-3) mM), while HEL cells received cytotoxic effects even when cultured in the medium containing 0.05 micrograms Be/ml (5.5 X 10(-3) mM), and these effects on the cells appeared strong when cultured in the medium without FBS. It was revealed from these experiments that HEL cells are very sensitive in terms of toxic effects of beryllium. Therefore, there cells can be used for the toxicological study on low level concentrations of the metal.

  17. Assessment of minute volume of lung in NPP workers for Korean reference man

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Y. J.; Song, S. H.; Lee, J.; Jin, Y. W.; Yim, Y. K.; Kim, J. S. [KNETEC, Seoul (Korea, Republic of)

    2001-05-01

    To formulation of the reference Korean for radiation protection purpose, we measured the forced vital capacity(FVC), forced expiratory volume in second(FEVI), minute ventilation(MV) of Nuclear Power Plant workers using SP-1 Spirometry Unit(Schiller AG. 1998) and eatimated the liters of breathed for working and resting, also compared these data with ICRP 23.

  18. Mineral resource of the month: beryllium

    Science.gov (United States)

    Shedd, Kim B.

    2006-01-01

    Beryllium metal is lighter than aluminum and stiffer than steel. These and other properties, including its strength, dimensional stability, thermal properties and reflectivity, make it useful for aerospace and defense applications, such as satellite and space-vehicle structural components. Beryllium’s nuclear properties, combined with its low density, make it useful as a neutron reflector and moderator in nuclear reactors. Because it is transparent to most X rays, beryllium is used as X-ray windows in medical, industrial and analytical equipment.

  19. Preliminary results for explosion bonding of beryllium to copper

    Energy Technology Data Exchange (ETDEWEB)

    Butler, D.J. [Northwest Technical Industries, Inc., Sequim, WA (United States); Dombrowski, D.E. [Brush Wellman, Inc., Cleveland, OH (United States)

    1995-09-01

    This program was undertaken to determine if explosive bonding is a viable technique for joining beryllium to copper substrates. The effort was a cursory attempt at trying to solve some of the problems associated with explosive bonding beryllium and should not be considered a comprehensive research effort. There are two issues that this program addressed. Can beryllium be explosive bonded to copper substrates and can the bonding take place without shattering the beryllium? Thirteen different explosive bonding iterations were completed using various thicknesses of beryllium that were manufactured with three different techniques.

  20. Guidance for the assessment of a chronic intake of workers in a nuclear fuel facility in Argentina

    Energy Technology Data Exchange (ETDEWEB)

    Rojo, A.M.; Spinella, M.R. [Autoridad Regulatoria Nuclear, Buenos Aires - Republica Argentina (Argentina); Gomez Parada, I. [Sociedad Argentina de Radioproteccio, Buenos Aires - Republica Argentina (Argentina)

    2006-07-01

    Todays trend for the design of internal dose monitoring programmes of workers applying the ICRP respiratory tract model requires taking into account the specific absorption parameters of the compounds and the physical data of the workplace aerosols. The aim of this analysis is to determine the specific ALIs and to establish reference levels for the assessment of chronic intake of workers, using the data from individual monitoring (pulmonary burden and urinary and fecal excretion) for natural uranium and uranium with 3.5 % and 20 % enrichment. In this paper the I.M.B.A. and AIDE software were used applying the respiratory tract model and the uranium biokinetic model published by ICRP taking into consideration the specific parameters of the uranium compounds. On the basis of this analysis, the relevance of lung, urine and faeces measurements in the individual monitoring of workers for internal dosimetry purposes is discussed It is concluded that these monitoring methods are useful for confirming that ALIs have not been exceeded and to assure that daily intakes are below the toxicological limits (2 mg/d) but it is necessary considering practical limitations of each method. (authors)

  1. Parallel assessment of male reproductive function in workers and wild rats exposed to pesticides in banana plantations in Guadeloupe

    Directory of Open Access Journals (Sweden)

    Huc-Terki Farida

    2008-07-01

    Full Text Available Abstract Background There is increasing evidence that reproductive abnormalities are increasing in frequency in both human population and among wild fauna. This increase is probably related to exposure to toxic contaminants in the environment. The use of sentinel species to raise alarms relating to human reproductive health has been strongly recommended. However, no simultaneous studies at the same site have been carried out in recent decades to evaluate the utility of wild animals for monitoring human reproductive disorders. We carried out a joint study in Guadeloupe assessing the reproductive function of workers exposed to pesticides in banana plantations and of male wild rats living in these plantations. Methods A cross-sectional study was performed to assess semen quality and reproductive hormones in banana workers and in men working in non-agricultural sectors. These reproductive parameters were also assessed in wild rats captured in the plantations and were compared with those in rats from areas not directly polluted by humans. Results No significant difference in sperm characteristics and/or hormones was found between workers exposed and not exposed to pesticide. By contrast, rats captured in the banana plantations had lower testosterone levels and gonadosomatic indices than control rats. Conclusion Wild rats seem to be more sensitive than humans to the effects of pesticide exposure on reproductive health. We conclude that the concept of sentinel species must be carefully validated as the actual nature of exposure may varies between human and wild species as well as the vulnerable time period of exposure and various ecological factors.

  2. Assessment of safety and health of storage workers - a psychosocial approach

    OpenAIRE

    Joanna Sadłowska-Wrzesińska

    2016-01-01

    Background: Although there is still a lot to do as far as prevention and elimination of traditional health and work safety hazards is concerned, the problem of psychosocial risk prevention is extremely important nowadays. It is crucial to take into consideration the health of workers and promotion of health in the workplace, as the occupational stress epidemics is getting more and more widespread. Methods: The article is based on the statistic analysis of accidents at work as well as the...

  3. Wages or Other Conditions: A Critical Assessment of Factors in Workers Performance in Nigeria

    Directory of Open Access Journals (Sweden)

    A. M. Ogaboh Agba

    2013-07-01

    Full Text Available The challenge of getting maximum performance from employees remain a perennial problem to managers in Nigeria. This challenge is aggravated by the great divide that exist among managers on which of the motivational factors stimulate workers the more into higher performance; while some tilt to monetary incentives; many more argue that non-monetary incentives are major motivating factors. Thus, this study is set to investigate factors that influence workers’ job performance in Nigeria. The study attempt to compare the influence of wages and other conditions service on employees’ performance. To achieve this objective, we elicited information from 300 respondents who were purposively sample from four organizations in some selected geo-political zones in Nigeria. Data collected were presented in graph, pie chart and bar chart. Findings reveal that, employee job performance are greatly influenced by regular and good wages; followed by conducive work environment, availability of internet facilities, good library, recognition/award, regular promotion, training opportunities, access to medical care and communication flow. We made the following recommendations among others, that managers of formal organizations should properly remunerate workers as well as provide conducive work environment for their employees. We posit that other least motivating factors as identified in this study should not ignore by managers, since each provide workers with a level of stimulant that propel them into maximum performance in work organization.

  4. A cross-sectional study to assess knowledge about HIV/AIDS transmission and prevention measures in company workers in Ecuador

    OpenAIRE

    Cabezas Guerra, Maria del Carmen; Fornasini, Marco; Dardenne, Nadia; Borja, Teresa; Albert, Adelin

    2013-01-01

    Background: HIV/AIDS was first reported in Ecuador in 1984 and its prevalence has been increasing ever since. In 2009, the National AIDS Program reported 21,810 HIV/AIDS cases and confirmed that the worker population was amongst the most affected groups. The objective of this study was to assess knowledge about HIV transmission and prevention measures in company workers in Ecuador. Methods: A cross-sectional survey based on a random sample of 115 companies (1,732 workers), stratified by t...

  5. Efficacy of surface sampling methods for different types of beryllium compounds.

    Science.gov (United States)

    Dufresne, A; Mocanu, T; Viau, S; Perrault, G; Dion, C

    2011-01-01

    The objective of the research work was to evaluate the efficiency of three different sampling methods (Ghost Wipe™, micro-vacuum, and ChemTest®) in the recovery of Be dust by assessing: (1) four Be compounds (beryllium acetate, beryllium chloride, beryllium oxide and beryllium aluminium), (2) three different surfaces (polystyrene, glass and aluminium) and (3) inter-operator variation. The three sampling methods were also tested on site in a laboratory of a dental school for validation purposes. The Ghost Wipe™ method showed recovery ranging from 43.3% to 85.8% for all four Be compounds and for all three quantities of Be spiked on Petri dishes, while recovery with the micro-vacuum method ranged from 0.1% to 12.4%. On polystyrene dishes with 0.4 µg Be, the recovery ranged from 48.3% to 81.7%, with an average recovery of 59.4% for Operator 1 and 68.4% for Operator 2. The ChemTest® wipe method with beryllium acetate, beryllium chloride, and AlBeMet® showed analogous results that are in line with the manufacturer's manual, but collection of beryllium oxide was negative. In the dental laboratory, Ghost Wipe™ samplings showed better recovery than the micro-vacuum method. The ratios between the recovered quantities of Be in each location where the Ghost Wipe™ was tested differed substantially, ranging from 1.45 to 64. In the dental laboratory, a faint blue color indicating the presence of Be was observed on the ChemTest® wipes used in two locations out of six. In summary, the Ghost Wipe™ method was more efficient than micro-vacuuming in collecting the Be dust from smooth, non-porous surfaces such as Petri dishes by a factor of approximately 18. The results obtained on site in a dental laboratory also showed better recovery with Ghost Wipes™. However, the ratio of Be recovered by Ghost Wipes™ versus micro-vacuuming was much lower for surfaces where a large amount of dust was present. Wet wiping is preferred over micro-vacuuming for beryllium forms, but

  6. Trace-level beryllium analysis in the laboratory and in the field: State of the art, challenges, and opportunities

    Energy Technology Data Exchange (ETDEWEB)

    BRISSON, MICHAEL

    2006-03-30

    Control of workplace exposure to beryllium is a growing issue in the United States and other nations. As the health risks associated with low-level exposure to beryllium are better understood, the need increases for improved analytical techniques both in the laboratory and in the field. These techniques also require a greater degree of standardization to permit reliable comparison of data obtained from different locations and at different times. Analysis of low-level beryllium samples, in the form of air filters or surface wipes, is frequently required for workplace monitoring or to provide data to support decision-making on implementation of exposure controls. In the United States and the United Kingdom, the current permissible exposure level is 2 {micro}g/m{sup 3} (air), and the United States Department of Energy has implemented an action level of 0.2 {micro}g/m{sup 3} (air) and 0.2 {micro}g/100 cm{sup 2} (surface). These low-level samples present a number of analytical challenges, including (1) a lack of suitable standard reference materials, (2) unknown robustness of sample preparation techniques, (3) interferences during analysis, (4) sensitivity (sufficiently low detection limits), (5) specificity (beryllium speciation), and (6) data comparability among laboratories. Additionally, there is a need for portable, real-time (or near real-time) equipment for beryllium air monitoring and surface wipe analysis that is both laboratory-validated and field-validated in a manner that would be accepted by national and/or international standards organizations. This paper provides a review of the current analytical requirements for trace-level beryllium analysis for worker protection, and also addresses issues that may change those requirements. The current analytical state of the art and relevant challenges facing the analytical community will be presented, followed by suggested criteria for real-time monitoring equipment. Recognizing and addressing these challenges will

  7. Assessment of biomarkers in asbestos-exposed workers as indicators of cancer risk.

    Science.gov (United States)

    Amati, Monica; Tomasetti, Marco; Mariotti, Laura; Tarquini, Lucia Miria; Valentino, Matteo; Santarelli, Lory

    2008-01-01

    Epidemiological studies have shown that mortality from malignant mesothelioma (MM) and lung cancer have increased with increasing cumulative exposure to asbestos. To investigate whether tumour-related biomarkers can contribute towards the evaluation of the carcinogenic risk in populations exposed to asbestos, the DNA adduct 8-hydroxy-2'-deoxyguanosine (80HdG), interleukine-6 (IL-6), platelet-derived growth factor (PDGF-BB), hepatocyte growth factor (HGF), basic fibroblast growth factor (bFGF), vascular endothelial growth factor (VEGFbeta) and soluble mesothelin-related peptides (SMRPs) were analysed in a cohort of workers differently exposed to asbestos fibres at the workplace. To document biomarker levels in an unexposed population, 54 age-matched subjects were enrolled. A total of 119 subjects with a history of occupational exposure to asbestos underwent clinical examination and were interviewed by trained personnel, responding to a detailed questionnaire related to duration of asbestos exposure, smoking, and occupational task. According to the occupational tasks, asbestos-exposed subjects were analysed for their asbestos cumulative dose and the association with the biomarkers was evaluated. Among the occupational groups, maintenance workers, pipe fitters and electricians were exposed to a higher cumulative dose of asbestos fibres. Exposure to asbestos significantly increased the steady-state content of 80HdG in DNA. Elevated levels of 80HdG and IL-6 best reflected a high level of SMRPs, which is related to cell transformation. Subjects heavily exposed to asbestos [> 60(ff/cm3) x years] showed also a higher level of angiogenic factors. A combination of angiogenic biomarkers with a specific mesothelioma-biomarker such as SMRPs could be used for close surveillance of workers with a history of asbestos exposure. PMID:18638565

  8. Control of beryllium powder at a DOE facility

    International Nuclear Information System (INIS)

    Beryllium is contained in a number of domestic and national defense items. Although many items might contain beryllium in some manner, few people need worry about the adverse effects caused by exposure to beryllium because it is the inhalable form of beryllium that is most toxic. Chronic beryllium disease (CBD), a granulomas and fibrotic lung disease with long latency, can be developed after inhalation exposures to beryllium. It is a progressive, debilitating lung disease. Its occurrence in those exposed to beryllium has been difficult to predict because some people seem to react to low concentration exposures whereas others do not react to high concentration exposures. Onset of the disease frequently occurs between 15 to 20 years after exposure begins. Some people develop the disease after many years of low concentration exposures but others do not develop CBD even though beryllium is shown to be present in lungs and urine. Conclusions based on these experiences are that their is some immunological dependence of developing CBD in about 3--4% of the exposed population, but the exact mechanism involved has not yet been identified. Acute beryllium disease can occur after a single exposure to a concentration of greater than 0.100 mg/m3 (inhalation exposure); it is characterized by the development of chemical pneumoconiosis, a respiratory disease. The acute effect of skin contact is a dermatitis characterized by itching and reddened, elevated, or fluid-accumulated lesions which appear particularly on the exposed surfaces of the body, especially the face, neck, arms, and hands. Small particles of beryllium that enter breaks in the skin can lead to the development of granulomas and/or open sores that do not heal until the beryllium has been removed. Our interest is only airborne beryllium, which is found in areas that machine or produce beryllium

  9. Assessment of safety and health of storage workers - a psychosocial approach

    Directory of Open Access Journals (Sweden)

    Joanna Sadłowska-Wrzesińska

    2016-03-01

    Full Text Available Background: Although there is still a lot to do as far as prevention and elimination of traditional health and work safety hazards is concerned, the problem of psychosocial risk prevention is extremely important nowadays. It is crucial to take into consideration the health of workers and promotion of health in the workplace, as the occupational stress epidemics is getting more and more widespread. Methods: The article is based on the statistic analysis of accidents at work as well as the analysis of health problems resulting from the job itself. The latest work safety reports have been reviewed and special attention has been paid to psychosocial risk analysis. The author has tried to explicate the terms of new and emerging risks as regards storage work. Results: Various threat aspects of storage work have been evaluated. Deficits in psychosocial hazard identification have been indicated. What is more, no correlation between occupational tasks of storage workers and their knowledge about psychosocial risks has been emphasized.  An exemplified approach to warehouse psychosocial threat identification has been presented. The approach is based on the diagnosis of the current situation.  Conclusions: The psychosocial risk of storage work may lead to health deterioration, greater accident risk and worse performance at work. Such consequences mean that the psychosocial risks affect both an individual and the organization. Therefore, we should expect more intense efforts to increase psychosocial risk awareness of both employers and employees.

  10. Aerosol resuspension from fabric: implications for personal monitoring in the beryllium industry.

    Science.gov (United States)

    Bohne, J E; Cohen, B S

    1985-02-01

    The fabric used for work clothing at an industrial site can significantly influence personal monitor (PM) exposure estimates because dust resuspension from clothing can increase the concentration at the sampler inlet. The magnitude of the effect depends on removal forces and on the interaction of the contaminant particles with work garments. Aerosol deposition and resuspension on cotton and Nomex aramid fabrics was evaluated at a beryllium refinery. Electrostatically charged cotton backdrops collected more beryllium than neutral controls, but electronegative Nomex backdrops did not. Moving fabrics collected more beryllium than did stationary controls. When contaminated fabrics were agitated, PMs mounted 2.5 cm in front of the fabric collected more beryllium than monitors above the fabric, positioned to simulate the nose or mouth. The difference between the air concentrations measured by these PMs increased with Be loading and tended to level off for highly contaminated fabric. Cotton resuspended a larger fraction of its contaminant load than Nomex. These results are consistent with current knowledge of the behavior of particles on fabric fibers. Aerosol resuspension from garments is an important consideration in assessing inhalation exposure to toxic dusts. A garment may attract and retain toxic particles. This contamination is then available for later resuspension. PMID:3976498

  11. Results of The Analysis of The Blood Beryllium Lymphocyte Proliferation Test Data From The Oak Ridge Y-12 Study

    Energy Technology Data Exchange (ETDEWEB)

    Frome, EL

    2001-12-18

    The potential hazards from exposure to beryllium or beryllium compounds in the workplace were first reported in the 1930s. The tritiated thymidine beryllium lymphocyte proliferation test (BeLPT) is an in vitro blood test that is widely used to screen beryllium exposed workers in the nuclear industry for sensitivity to beryllium. Newman [18] has discussed the clinical significance of the BeLPT and described a standard protocol that was developed in the late 1980s. Cell proliferation is measured by the incorporation of tritiated thymidine into dividing cells on two culture dates and using three concentrations of beryllium sulfate. Results are expressed as a ''stimulation index'' (SI) which is the ratio of the amount of tritiated thymidine (measured by beta counts) in the stimulated cells divided by the counts for the unstimulated cells on the same culture day. Several statistical methods for use in the routine analysis of the BeLPT were considered in the early 1990's by Frome et al. [7]. The least absolute values (LAV) method was recommended for routine analysis of the BeLPT. The purposes of this report are to further evaluate the LAV method using new data, and to describe a new method for identification of an abnormal or borderline test. This new statistical biological positive (SBP) method reflects the clinical judgment that (1) at least two SIs show a ''positive'' response to beryllium, and (2), that the maximum of the six SIs must exceed a cut point that is determined from a reference data set of normal individuals whose blood has been tested by the same method in the same serum. The new data is from the Y-12 facility in Oak Ridge and consist of 1080 worker and 33 nonexposed control BeLPTs (all tested in the same serum). Graphical results are presented to explain the statistical method, and the new SBP method is applied to the Y-12 group. The true positive rate and specificity of the new method were estimated to be 86

  12. Study on neutron irradiation behavior of beryllium as neutron multiplier

    Energy Technology Data Exchange (ETDEWEB)

    Ishitsuka, Etsuo [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment

    1998-03-01

    More than 300 tons beryllium is expected to be used as a neutron multiplier in ITER, and study on the neutron irradiation behavior of beryllium as the neutron multiplier with Japan Materials Testing Reactor (JMTR) were performed to get the engineering data for fusion blanket design. This study started as the study on the tritium behavior in beryllium neutron reflector in order to make clear the generation mechanism on tritium of JMTR primary coolant since 1985. These experiences were handed over to beryllium studies for fusion study, and overall studies such as production technology of beryllium pebbles, irradiation behavior evaluation and reprocessing technology have been started since 1990. In this presentation, study on the neutron irradiation behavior of beryllium as the neutron multiplier with JMTR was reviewed from the point of tritium release, thermal properties, mechanical properties and reprocessing technology. (author)

  13. Status of material development for lifetime expansion of beryllium reflector

    International Nuclear Information System (INIS)

    Beryllium has been used as the reflector element material in the reactor, specifically S-200F structural grade beryllium manufactured by Materion Brush Beryllium and Composites (former, Brush Wellman Inc.). As a part of the reactor upgrade, the Japan Atomic Energy Agency (JAEA) also has carried out the cooperation experiments to extend the operating lifetime of the beryllium reflector elements. It will first be necessary to determine which of the material's physical, mechanical and chemical properties will be the most influential on that choice. The irradiation testing plans to evaluate the various beryllium grades are also briefly considered and prepared. In this paper, material selection, irradiation test plan and PEI development for lifetime expansion of beryllium are described for material testing reactors. (author)

  14. Mechanisms of hydrogen retention in metallic beryllium and beryllium oxide and properties of ion-induced beryllium nitride; Rueckhaltemechanismen fuer Wasserstoff in metallischem Beryllium und Berylliumoxid sowie Eigenschaften von ioneninduziertem Berylliumnitrid

    Energy Technology Data Exchange (ETDEWEB)

    Oberkofler, Martin

    2011-09-22

    In the framework of this thesis laboratory experiments on atomically clean beryllium surfaces were performed. They aim at a basic understanding of the mechanisms occurring upon interaction of a fusion plasma with a beryllium first wall. The retention and the temperature dependent release of implanted deuterium ions are investigated. An atomistic description is developed through simulations and through the comparison with calculations based on density functional theory. The results of these investigations are compared to the behaviour of hydrogen upon implantation into thermally grown beryllium oxide layers. Furthermore, beryllium nitride is produced by implantation of nitrogen into metallic beryllium and its properties are investigated. The results are interpreted with regard to the use of beryllium in a fusion reactor. (orig.)

  15. Characterization of plasma sprayed beryllium ITER first wall mockups

    Energy Technology Data Exchange (ETDEWEB)

    Castro, R.G.; Vaidya, R.U.; Hollis, K.J. [Los Alamos National Lab., NM (United States). Material Science and Technology Div.

    1998-01-01

    ITER first wall beryllium mockups, which were fabricated by vacuum plasma spraying the beryllium armor, have survived 3000 thermal fatigue cycles at 1 MW/m{sup 2} without damage during high heat flux testing at the Plasma Materials Test Facility at Sandia National Laboratory in New Mexico. The thermal and mechanical properties of the plasma sprayed beryllium armor have been characterized. Results are reported on the chemical composition of the beryllium armor in the as-deposited condition, the through thickness and normal to the through thickness thermal conductivity and thermal expansion, the four-point bend flexure strength and edge-notch fracture toughness of the beryllium armor, the bond strength between the beryllium armor and the underlying heat sink material, and ultrasonic C-scans of the Be/heat sink interface. (author)

  16. Toward universal coverage in Afghanistan: A multi-stakeholder assessment of capacity investments in the community health worker system.

    Science.gov (United States)

    Edward, Anbrasi; Branchini, Casey; Aitken, Iain; Roach, Melissa; Osei-Bonsu, Kojo; Arwal, Said Habib

    2015-11-01

    Global efforts to scale-up the community health workforce have accelerated as a result of the growing evidence of their effectiveness to enhance coverage and health outcomes. Reconstruction efforts in Afghanistan integrated capacity investments for community based service delivery, including the deployment of over 28,000 community health workers (CHWs) to ensure access to basic preventive and curative services. The study aimed to conduct capacity assessments of the CHW system and determine stakeholder perspectives of CHW performance. Structured interviews were conducted on a national sample from 33 provinces and included supervisors, facility providers, patients, and CHWs. Formative assessments were also conducted with national policymakers, community members and health councils in two provinces. Results indicate that more than 70% of the NGO's provide comprehensive training for CHWs, 95% CHWs reported regular supervision, and more than 60% of the health posts had adequate infrastructure and essential commodities. Innovative strategies of paired male and female CHWs, institution of a special cadre of community health supervisors, and community health councils were introduced as systems strengthening mechanisms. Reported barriers included unrealistic and expanding task expectations (14%), unsatisfactory compensation mechanisms (75%), inadequate transport (69%), and lack of commodities (40%). Formative assessments evidenced that CHWs were highly valued as they provided equitable, accessible and affordable 24-h care. Their loyalty, dedication and the ability for women to access care without male family escorts was appreciated by communities. With rising concerns of workforce deficits, insecurity and budget constraints, the health system must enhance the capacity of these frontline workers to improve the continuum of care. The study provides critical insight into the strengths and constraints of Afghanistan's CHW system, warranting further efforts to contextualize

  17. Personal radiation monitoring and assessment of doses received by radiation workers (1996)

    International Nuclear Information System (INIS)

    Since late 1986, all persons monitored by the Australian Radiation Laboratory have been registered on a data base which maintains records of the doses received by each individual wearer. At present, the Service regularly monitors approximately 30,000 persons, which is roughly 90 percent of those monitored in Australia, and maintains dose histories of over 75,000 people. The skin dose for occupationally exposed workers can be measured by using one of the five types of monitor issued by the Service: Thermoluminescent Dosemeter (TLD monitor), Finger TLD 3, Neutron Monitor, Special TLD and Environmental monitor. The technical description of the monitors is provided along with the method for calculating the radiation dose. 5 refs., 7 tabs., 5 figs

  18. Personal radiation monitoring and assessment of doses received by radiation workers (1996)

    Energy Technology Data Exchange (ETDEWEB)

    Morris, N.D.

    1996-12-01

    Since late 1986, all persons monitored by the Australian Radiation Laboratory have been registered on a data base which maintains records of the doses received by each individual wearer. At present, the Service regularly monitors approximately 30,000 persons, which is roughly 90 percent of those monitored in Australia, and maintains dose histories of over 75,000 people. The skin dose for occupationally exposed workers can be measured by using one of the five types of monitor issued by the Service: Thermoluminescent Dosemeter (TLD monitor), Finger TLD 3, Neutron Monitor, Special TLD and Environmental monitor. The technical description of the monitors is provided along with the method for calculating the radiation dose. 5 refs., 7 tabs., 5 figs.

  19. Effective dose assessment for workers in caves in the Czech Republic: Experiments with passive radon detectors

    International Nuclear Information System (INIS)

    The new RAMARN system for radon volume activity measurement was developed in 2003 and has been in use since then. RAMARN system consists of a plastic chamber that is conically cylindrical in shape and about 0.5 l in volume; a bare Kodak LR 115 is located on the bottom of this diffusion chamber. The size was chosen to avoid the influence of deposited decay products of radon. Kodak has a spectrometric character - the tracks are visualized only for alphas with energies between 1 and 3 MeV that touch the foil; thus the effective volume has a lens shape. The response therefore corresponds to diffused radon and half of 218Po born by radon gas decay. The experiments described below were conducted as one part of a routine methodology control, focused on classifying worker irradiation from natural ionizing radiation sources in show caves and in caves used for speleo-therapy. (authors)

  20. Plasma cleaning of beryllium coated mirrors

    Science.gov (United States)

    Moser, L.; Marot, L.; Steiner, R.; Newman, M.; Widdowson, A.; Ivanova, D.; Likonen, J.; Petersson, P.; Pintsuk, G.; Rubel, M.; Meyer, E.; Contributors, JET

    2016-02-01

    Cleaning systems of metallic first mirrors are needed in more than 20 optical diagnostic systems from ITER to avoid reflectivity losses. Currently, plasma sputtering is considered as one of the most promising techniques to remove deposits coming from the main wall (mainly beryllium and tungsten). This work presents the results of plasma cleaning of rhodium and molybdenum mirrors exposed in JET-ILW and contaminated with typical tokamak elements (including beryllium and tungsten). Using radio frequency (13.56 MHz) argon or helium plasma, the removal of mixed layers was demonstrated and mirror reflectivity improved towards initial values. The cleaning was evaluated by performing reflectivity measurements, scanning electron microscopy, x-ray photoelectron spectroscopy and ion beam analysis.

  1. Neutron counter based on beryllium activation

    Energy Technology Data Exchange (ETDEWEB)

    Bienkowska, B.; Prokopowicz, R.; Kaczmarczyk, J.; Paducha, M. [Institute of Plasma Physics and Laser Microfusion (IPPLM), Hery 23, 01-497 Warsaw (Poland); Scholz, M.; Igielski, A. [Institute of Nuclear Physics PAS (IFJPAN), Radzikowskiego 152, 31-342 Krakow (Poland); Karpinski, L. [Faculty of Electrical Engineering, Rzeszow University of Technology, Pola 2, 35-959 Rzeszow (Poland); Pytel, K. [National Centre for Nuclear Research (NCBJ), Soltana 7, 05-400 Otwock - Swierk (Poland)

    2014-08-21

    The fusion reaction occurring in DD plasma is followed by emission of 2.45 MeV neutrons, which carry out information about fusion reaction rate and plasma parameters and properties as well. Neutron activation of beryllium has been chosen for detection of DD fusion neutrons. The cross-section for reaction {sup 9}Be(n, α){sup 6}He has a useful threshold near 1 MeV, which means that undesirable multiple-scattered neutrons do not undergo that reaction and therefore are not recorded. The product of the reaction, {sup 6}He, decays with half-life T{sub 1/2} = 0.807 s emitting β{sup −} particles which are easy to detect. Large area gas sealed proportional detector has been chosen as a counter of β–particles leaving activated beryllium plate. The plate with optimized dimensions adjoins the proportional counter entrance window. Such set-up is also equipped with appropriate electronic components and forms beryllium neutron activation counter. The neutron flux density on beryllium plate can be determined from the number of counts. The proper calibration procedure needs to be performed, therefore, to establish such relation. The measurements with the use of known β–source have been done. In order to determine the detector response function such experiment have been modeled by means of MCNP5–the Monte Carlo transport code. It allowed proper application of the results of transport calculations of β{sup −} particles emitted from radioactive {sup 6}He and reaching proportional detector active volume. In order to test the counter system and measuring procedure a number of experiments have been performed on PF devices. The experimental conditions have been simulated by means of MCNP5. The correctness of simulation outcome have been proved by measurements with known radioactive neutron source. The results of the DD fusion neutron measurements have been compared with other neutron diagnostics.

  2. Neutron counter based on beryllium activation

    Science.gov (United States)

    Bienkowska, B.; Prokopowicz, R.; Scholz, M.; Kaczmarczyk, J.; Igielski, A.; Karpinski, L.; Paducha, M.; Pytel, K.

    2014-08-01

    The fusion reaction occurring in DD plasma is followed by emission of 2.45 MeV neutrons, which carry out information about fusion reaction rate and plasma parameters and properties as well. Neutron activation of beryllium has been chosen for detection of DD fusion neutrons. The cross-section for reaction 9Be(n, α)6He has a useful threshold near 1 MeV, which means that undesirable multiple-scattered neutrons do not undergo that reaction and therefore are not recorded. The product of the reaction, 6He, decays with half-life T1/2 = 0.807 s emitting β- particles which are easy to detect. Large area gas sealed proportional detector has been chosen as a counter of β-particles leaving activated beryllium plate. The plate with optimized dimensions adjoins the proportional counter entrance window. Such set-up is also equipped with appropriate electronic components and forms beryllium neutron activation counter. The neutron flux density on beryllium plate can be determined from the number of counts. The proper calibration procedure needs to be performed, therefore, to establish such relation. The measurements with the use of known β-source have been done. In order to determine the detector response function such experiment have been modeled by means of MCNP5-the Monte Carlo transport code. It allowed proper application of the results of transport calculations of β- particles emitted from radioactive 6He and reaching proportional detector active volume. In order to test the counter system and measuring procedure a number of experiments have been performed on PF devices. The experimental conditions have been simulated by means of MCNP5. The correctness of simulation outcome have been proved by measurements with known radioactive neutron source. The results of the DD fusion neutron measurements have been compared with other neutron diagnostics.

  3. Behavior of beryllium pebbles under irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Dalle-Donne, M.; Scaffidi-Argentina, F. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reactortechnik; Baldwin, D.L.; Gelles, D.S.; Greenwood, L.R.; Kawamura, H.; Oliver, B.M.

    1998-01-01

    Beryllium pebbles are being considered in fusion reactor blanket designs as neutron multiplier. An example is the European `Helium Cooled Pebble Bed Blanket.` Several forms of beryllium pebbles are commercially available but little is known about these forms in response to fast neutron irradiation. Commercially available beryllium pebbles have been irradiated to approximately 1.3 x 10{sup 22} n/cm{sup 2} (E>1 MeV) at 390degC. Pebbles 1-mm in diameter manufactured by Brush Wellman, USA and by Nippon Gaishi Company, Japan, and 3-mm pebbles manufactured by Brush Wellman were included. All were irradiated in the below-core area of the Experimental Breeder Reactor-II in Idaho Falls, USA, in molybdenum alloy capsules containing helium. Post-irradiation results are presented on density change measurements, tritium release by assay, stepped-temperature anneal, and thermal ramp desorption tests, and helium release by assay and stepped-temperature anneal measurements, for Be pebbles from two manufacturing methods, and with two specimen diameters. The experimental results on density change and tritium and helium release are compared with the predictions of the code ANFIBE. (author)

  4. Dynamic behaviour of S200F beryllium

    International Nuclear Information System (INIS)

    Compression tests have been made on a large scale of strain, strain rate (up to 2000 s-1) and temperature (between 20 C and 300 C). From these experiences, we have calculated a constitutive model for beryllium S200F, which can be used by computer codes. Its formulation is not far from Steinberg, Cochran and Guinan's. But in our case, the influences of temperature and strain rate appear clearly within the expression. To validate our equation, we have used it in a computer code. Its extrapolation for higher strain rates is in good agreement with experiments such as Taylor impact tests or plate impact tests (strain rates greater than 104 s-1). With micrography, we could settle a link between the main strain mode within the material, and the variation of one parameter of the model. Beside the constitutive model, we have shown that shock loaded beryllium behaves in two different ways. If the strain rate is lower than 5.106 s-1, then it is proportional to the squared shock pressure. Beyond, it is a linear function of shock pressure to the power of four. By a spall study on beryllium, we have confirmed that it is excessively fragile. Its fracture is sudden, at a strength near 1 GPa. (author)

  5. Interaction of nitrogen ions with beryllium surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Dobes, Katharina [Institute of Applied Physics, TU Wien, Association EURATOM ÖAW, Vienna (Austria); Köppen, Martin [Institute of Energy and Climate Research – Plasma Physics, Forschungszentrum Jülich GmbH, 52425 Jülich (Germany); Oberkofler, Martin [Max-Planck-Institut für Plasmaphysik, Boltzmannstraße 2, D-85748 Garching (Germany); Lungu, Cristian P.; Porosnicu, Corneliu [National Institute for Laser, Plasma, and Radiation Physics, Bucharest (Romania); Höschen, Till; Meisl, Gerd [Max-Planck-Institut für Plasmaphysik, Boltzmannstraße 2, D-85748 Garching (Germany); Linsmeier, Christian [Institute of Energy and Climate Research – Plasma Physics, Forschungszentrum Jülich GmbH, 52425 Jülich (Germany); Aumayr, Friedrich, E-mail: aumayr@iap.tuwien.ac.at [Institute of Applied Physics, TU Wien, Association EURATOM ÖAW, Vienna (Austria)

    2014-12-01

    The interaction of energetic nitrogen projectiles with a beryllium surface is studied using a highly sensitive quartz crystal microbalance technique. The overall mass change rate of the beryllium sample under N{sub 2}{sup +} ion impact at an ion energy of 5000 eV (i.e. 2500 eV per N) is investigated in situ and in real-time. A strong dependency of the observed mass change rate on the nitrogen fluence (at constant flux) is found and can be attributed to the formation of a nitrogen-containing mixed material layer within the ion penetration depth. The presented data elucidate the dynamics of the interaction process and the surface saturation with increasing nitrogen fluence in a unique way. Basically, distinct interaction regimes can be discriminated, which can be linked to the evolution of the surface composition upon nitrogen impact. Steady state surface conditions are obtained at a total cumulative nitrogen fluence of ∼80 × 10{sup 16} N atoms per cm{sup 2}. In dynamic equilibrium, the interaction is marked by continuous surface erosion. In this case, the observed total sputtering yield becomes independent from the applied nitrogen fluence and is of the order of 0.4 beryllium atoms per impinging nitrogen atom.

  6. Beryllium-10 in Australasian tektites - Evidence for a sedimentary precursor

    Science.gov (United States)

    Pal, D. K.; Moniot, R. K.; Kruse, T. H.; Herzog, G. F.; Tuniz, C.

    1982-01-01

    Each of seven Australasian tektites contains about 100 micron atoms of beryllium-10 (half-life, 1.53 million years) per gram. Cosmic-ray bombardment of the australites cannot have produced the measured amounts of beryllium-10 either at the earth's surface or in space. The beryllium-10 contents of these australites are consistent with a sedimentary precursor that adsorbed from precipitation beryllium-10 produced in the atmosphere. The sediments must have spent several thousand years at the earth's surface within a few million years of the tektite-producing event.

  7. Tritium release from neutron irradiated beryllium: Kinetics, long-time annealing and effect or crack formation

    Energy Technology Data Exchange (ETDEWEB)

    Scaffidi-Argentina, F.; Werle, H. [Forschungszentrum Karlsruhe, (Germany)

    1995-09-01

    Since beryllium is considered as one of the best neutron multiplier materials in the blanket of the next generation fusion reactors, several studies have been started to evaluate its behaviour under irradiation during both operating and accidental conditions. Based on safety considerations, tritium produced in beryllium during neutron irradiation represents one important issue, therefore it is necessary to investigate tritium transport processes by using a comprehensive mathematical model and comparing its predictions with well characterized experimental tests. Because of the difficulties in extrapolating the short-time tritium release tests to a longer time scale, also long-time annealing experiments with beryllium samples from the SIBELIUS irradiation. have been carried out at the Forschungszentrum Karlsruhe. Samples were annealed up to 12 months at temperatures up to 650{degrees}C. The inventory after annealing was determined by heating the samples up to 1050{degrees}C with a He+0.1 vo1% H{sub 2} purge gas. Furthermore, in order to investigate the likely effects of cracks formation eventually causing a faster tritium release from beryllium, the behaviour of samples irradiated at low temperature (40-50{degrees}C) but up to very high fast neutron fluences (0.8-3.9{center_dot}10{sup 22} cm{sup -2}, E{sub n}{ge}1 MeV) in the BR2 reactor has been investigated. Tritium was released by heating the beryllium samples up to 1050{degrees}C and purging them with He+0.1 vo1% H{sub 2}. Tritium release from high-irradiated beryllium samples showed a much faster kinetics than from the low-irradiated ones, probably because of crack formation caused by thermal stresses in the brittle material and/or by helium bubbles migration. The obtained experimental data have been compared with predictions of the code ANFIBE with the goal to better understand the physical mechanisms governing tritium behaviour in beryllium and to assess the prediction capabilities of the code.

  8. Design of the beryllium window for Brookhaven Linac Isotope Producer

    Energy Technology Data Exchange (ETDEWEB)

    Nayak, S. [Brookhaven National Lab. (BNL), Upton, NY (United States); Mapes, M. [Brookhaven National Lab. (BNL), Upton, NY (United States); Raparia, D. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2015-11-01

    In the Brookhaven Linac Isotope Producer (BLIP) beam line, there were two Beryllium (Be) windows with an air gap to separate the high vacuum upstream side from low vacuum downstream side. There had been frequent window failures in the past which affected the machine productivity and increased the radiation dose received by workers due to unplanned maintenance. To improve the window life, design of Be window is reexamined. Detailed structural and thermal simulations are carried out on Be window for different design parameters and loading conditions to come up with better design to improve the window life. The new design removed the air gap and connect the both beam lines with a Be window in-between. The new design has multiple advantages such as 1) reduces the beam energy loss (because of one window with no air gap), 2) reduces air activation due to nuclear radiation and 3) increased the machine reliability as there is no direct pressure load during operation. For quick replacement of this window, an aluminum bellow coupled with load binder was designed. There hasn’t been a single window failure since the new design was implemented in 2012.

  9. Assessment of Some Immune Parameters in Occupationally Exposed Nuclear Power Plants Workers

    Science.gov (United States)

    Panova, Delyana; Djounova, Jana; Rupova, Ivanka; Penkova, Kalina

    2015-01-01

    The purpose of this article is to analyze the results of a 10-year survey of the radiation effects of some immune parameters of occupationally exposed personnel from the Nuclear Power Plant “Kozloduy”, Bulgaria. 438 persons working in NPP with cumulative doses between 0.06 mSv and 766.36mSv and a control group with 65 persons were studied. Flow cytometry measurements of T, B, natural killer (NK) and natural killer T (NKT) cell lymphocyte populations were performed. Data were interpreted with regard to cumulative doses, length of service and age. The average values of the studied parameters of cellular immunity were in the reference range relative to age and for most of the workers were not significantly different from the control values. Low doses of ionizing radiation showed some trends of change in the number of CD3+CD4+ helper-inducer lymphocytes, CD3+ CD8+ and NKT cell counts. The observed changes in some of the studied parameters could be interpreted in terms of adaptation processes at low doses. At doses above 100–200 mSv, compensatory mechanisms might be involved to balance deviations in lymphocyte subsets. The observed variations in some cases could not be attributed only to the radiation exposure because of the impact of a number of other exogenous and endogenous factors on the immune system. PMID:26675014

  10. Study of Peak Expiratory Flow Rate as the Assessment of Lung Function in Occupationally Exposed Petrol Pump Workers of Western Maharashtra

    Directory of Open Access Journals (Sweden)

    Patil Smita V

    2016-04-01

    Full Text Available Background: Fast urbanization trends, rapid industrial growth, globalization, and poor environmental conditions at work places have created a lot of healthrelated issues. Aim and Objectives: The aim of this study is to investigate Peak Expiratory Flow Rate (PEFR as the assessment of lung function in occupationally exposed petrol pump workers and also check whether PEFR increases or decreases with duration of exposure. Material and Methods: The study was conducted on 60 male petrol pump workers between age group of 20-40 years who were working as petrol filling attendants for more than one year from western Maharashtra. 50 normal healthy males with same socioeconomic status were chosen as controls to find out the effect of occupational exposure to petroleum product on PEFR as the assessment of lung function tests. Petrol pump workers were divided into three groups based on their duration of exposure i.e. 1- 5 yrs, 6- 10 yrs and more than 11 years. PEFR of petrol pump workers and control was measured by using a Mini Wright peak flow meter which is a portable device for measuring ventilator functions. Comparisons was done using unpaired t-test for 2 groups comparisons and one way ANOVAfor multiple groups of exposures. Results: The PEFR was significantly lower decrease (p=0.001 around petrol pump workers (389.17 as compared to control (534.2. As year of exposure increased mean value of PEFR was significantly decreased from 452.17, 378.00 and 283.64 respectively in petrol pump workers. Conclusion: The results suggested that respiratory functions i.e. PEFR of occupationally exposed petrol pump workers are significantly reduced as compared to controls, also PEFR is significantly reduced with increase in the duration of exposure.

  11. Continuing Education on Suicide Assessment and Crisis Intervention for Social Workers and Other Mental Health Professionals: A Follow-Up Study

    Science.gov (United States)

    Mirick, Rebecca G.; Bridger, Joanna; McCauley, James; Berkowitz, Larry

    2016-01-01

    Historically, graduate training programs have not taught suicide assessment and intervention skills in depth; therefore, the development of effective continuing education offerings is relevant and necessary for practicing social workers. Although the ability to increase knowledge and confidence is critical, a focus on competency-based education…

  12. Experiments on studying beryllium - steam interaction, determination of oxidated beryllium emissivity factor

    International Nuclear Information System (INIS)

    The report presents results of beryllium emissivity factor measurements within 700-1300 K temperature range. The tests were conducted at Institute of Atomic Energy of the National Nuclear Center of the Republic of Kazakhstan to receive experimental data for verification of calculation programs describing an accident involving water coolant discharge into ITER reactor vacuum cavity. (author)

  13. Beryllium toxicity testing in the suspension culture of mouse fibroblasts.

    Science.gov (United States)

    Rössner, P; Bencko, V

    1980-01-01

    Suspension culture of mouse fibroblast cell line L-A 115 was used to test beryllium toxicity in the presence of magnesium ions. Beryllium added to the MEM cultivation medium was bound in a complex with sulphosalicylic acid BeSSA complex, because the use of beryllium chloride turned out to yield ineffective beryllium phosphate that formed macroscopically detectable insoluble opacities. The BeSSA complex was used in the concentration range: 10(-3)--10(-9)M, magnesium was used in 3 concentrations: 10(-1)M, 5 x 10(-2)M and 10(-2)M. Growth curve analysis revealed pronounced beryllium toxicity at the concentration of 10(-3)M, magnesium-produced toxic changes were observed only at the concentration of 10(-1)M. No competition between the beryllium and magnesium ions was recorded. It is assumed that the possible beryllium-magnesium competition was significantly modified by the use of BeSSA complex-bound beryllium.

  14. Ionization energies of beryllium in strong magnetic fields

    Institute of Scientific and Technical Information of China (English)

    GUANXiao-xu; ZHANGYue-xia

    2004-01-01

    We have develop an effective frozen core approximation to calculate energy levels and ionization enegies of the beryllium atom in magnetic field strengths up to 2.35 × 105T. Systematic improvement over the Hartree-Fock results for the beryllium low-lying states has been accomplished.

  15. Joining of beryllium by braze welding technique: preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Banaim, P.; Abramov, E. [Ben-Gurion Univ. of the Negev, Beersheba (Israel); Zalkind, S.; Eden, S.

    1998-01-01

    Within the framework of some applications, there is a need to join beryllium parts to each other. Gas Tungsten Arc Braze Welds were made in beryllium using 0.3 mm commercially Aluminum (1100) shim preplaced at the joint. The welds exhibited a tendency to form microcracks in the Fusion Zone and Heat Affected Zone. All the microcracks were backfilled with Aluminum. (author)

  16. Protection of air in premises and environment against beryllium aerosols

    Energy Technology Data Exchange (ETDEWEB)

    Bitkolov, N.Z.; Vishnevsky, E.P.; Krupkin, A.V. [Research Inst. of Industrial and Marine Medicine, St. Petersburg (Russian Federation)

    1998-01-01

    First and foremost, the danger of beryllium aerosols concerns a possibility of their inhalation. The situation is aggravated with high biological activity of the beryllium in a human lung. The small allowable beryllium aerosols` concentration in air poses a rather complex and expensive problem of the pollution prevention and clearing up of air. The delivery and transportation of beryllium aerosols from sites of their formation are defined by the circuit of ventilation, that forms aerodynamics of air flows in premises, and aerodynamic links between premises. The causes of aerosols release in air of premises from hoods, isolated and hermetically sealed vessels can be vibrations, as well as pulses of temperature and pressure. Furthermore, it is possible the redispersion of aerosols from dirty surfaces. The effective protection of air against beryllium aerosols at industrial plants is provided by a complex of hygienic measures: from individual means of breath protection up to collective means of the prevention of air pollution. (J.P.N.)

  17. Preparation and characterization of beryllium doped organic plasma polymer coatings

    International Nuclear Information System (INIS)

    We report the formation of beryllium doped plasma polymerized coatings derived from a helical resonator deposition apparatus, using diethylberyllium as the organometaric source. These coatings had an appearance not unlike plain plasma polymer and were relatively stable to ambient exposure. The coatings were characterized by Inductively Coupled Plasma Mass Spectrometry and X-Ray Photoelectron Spectroscopy. Coating rates approaching 0.7 μm hr-1 were obtained with a beryllium-to-carbon ratio of 1:1.3. There is also a significant oxygen presence in the coating as well which is attributed to oxidation upon exposure of the coating to air. The XPS data show only one peak for beryllium with the preponderance of the XPS data suggesting that the beryllium exists as BeO. Diethylberyllium was found to be inadequate as a source for beryllium doped plasma polymer, due to thermal decomposition and low vapor recovery rates

  18. Spectrofluorimetric Determination of Beryllium by Mean Centering of Ratio Spectra.

    Science.gov (United States)

    Chamsaz, Mahmoud; Samghani, Kobra; Arbab-Zavar, Mohammad Hossein; Heidari, Tahereh

    2016-07-01

    Trace amounts of beryllium has been determined by spectrofluorimetric method that used morin as fluorimetric reagent. Beryllium gives a highly fluorescent complex with morin. The excitation wavelength of morin and Be-morin complex were 410 and 430. The fluorescence spectra of morin and Be-morin complex were overlaped in excitation wavelength of 430 nm. A method based on mean centering of ratio spectra has been performed to remove the interference caused by morin as it overlaps with the Be-morin spectra. The linear range of beryllium concentration is in 0.2-200 ppb range. The parameters of detection limit and RSD were 0.18 ppb and 4.6 % respectively. This method was used for determination of beryllium in copper-beryllium alloy as a real sample. In determination of Be(II), the interference by Cu(II) was very serious, which was eliminated by adding triethanolamine. PMID:27265354

  19. The Usefulness of Assessing and Identifying Workers' Temperaments and Their Effects on Occupational Stress in the Workplace.

    Directory of Open Access Journals (Sweden)

    Yasuhiko Deguchi

    Full Text Available The relationship between temperaments and mental disorders has been reported in previous studies, but there has been little attention to temperaments in the occupational safety and health research. The aim of this study was to clarify the effects of temperaments on occupational stress among local government employees. The subjects were 145 Japanese daytime workers in local government. Temperaments were assessed by the Temperament Evaluation of Memphis, Pisa, Paris, and San Diego-Auto questionnaire (TEMPS-A. Occupational stress was assessed using the Generic Job Stress Questionnaire (GJSQ. Hierarchical multiple linear regression analysis was used. Hyperthymic temperament predicted a higher level of job control, and a lower level of role ambiguity and job future ambiguity. Irritable temperament predicted a lower level of social support from supervisors and a higher level of role conflict, variance in workload and intragroup conflict. Anxious temperament predicted a lower level of social support from coworkers and a higher level of job future ambiguity. The sample size was small. Only Japanese local government employees were surveyed. Hyperthymic temperament played a protective role, and irritable, anxious temperament played a vulnerable role against one's own occupational stress and recognizing the roles they play in work life would lead to self-insight. Additionally, recognition of the temperaments and temperament-related stressors by one's supervisors or coworkers would facilitate provision of social support.

  20. Monitoring and assessment of individual doses of occupationally exposed workers due to external radiation

    International Nuclear Information System (INIS)

    Exposure to external radiation occurs in many occupations. Any exposure to ionizing radiation has the tendency to change the biochemical make-up of the human body which may result in biological health effects of ionizing radiation. This study reviews the monitoring and assessment of external radiation doses in industrial radiography using thermoluminescence and direct reading dosimeters. Poor handling procedures such as inadequate engineering control of equipment, safety culture, management, and inadequate assessment and monitoring of doses are the causes of most of the reported cases of exposure to external radiation in industrial radiography. Occupational exposure data in industrial radiography taken from UNSCEAR report 2008 was discussed and recommendations were made to regulatory authorities, operating organizations and radiographers. (au)

  1. Monitoring and assessment of individual doses of occupationally exposed workers due to external radiation

    International Nuclear Information System (INIS)

    Exposure to external radiation occurs in many occupations. Any exposure to ionizing radiation has the tendency to change the biochemical make-up of the human body which may result in biological health effects of ionizing radiation. This study reviews the monitoring and assessment of external radiation doses in industrial radiography using thermoluminescence and direct reading dosimeters. Poor handling procedures such as inadequate engineering control of equipment, safety culture, management, and inadequate assessment and monitoring of doses are the causes of most of the reported cases of exposure to external radiation in industrial radiography. Occupational exposure data in industrial radiography from UNSCEAR report 2008 was discussed and recommendations were made to regulatory authorities, operating organizations and radiographers. (au)

  2. Pulmonary and gastric lead burden assessment for lead-recycling plant workers

    OpenAIRE

    Uzu, Gaëlle; Sauvain, Jean-Jacques; Baeza, Armelle; Riediker, Michael; Sanchez Sandoval Hohl, Magdalena; Val, Stéphanie; Tack, Karine; Denys, Sébastien; Pradere, Philippe; Dumat, Camille

    2011-01-01

    As a function of PM size (PM10-2.5, PM2.5-1 and PM1) and origin (furnace, refining and channeled emissions), lead toxicity and bioaccessibility assessment were performed in a lead recycling plant using complementary biologic and chemical acellular tests. According to their origin, process PM displays differences in metal contents, granulometry and percentage of inhalable fraction. Lead gastric bioaccessibility was relatively low (maximum 25%) in comparison with previous available studies, tho...

  3. Gauging U.S. Emergency Medical Services workers' willingness to respond to pandemic influenza using a threat- and efficacy-based assessment framework.

    Directory of Open Access Journals (Sweden)

    Daniel J Barnett

    Full Text Available BACKGROUND: Emergency Medical Services workers' willingness to report to duty in an influenza pandemic is essential to healthcare system surge amidst a global threat. Application of Witte's Extended Parallel Process Model (EPPM has shown utility for revealing influences of perceived threat and efficacy on non-EMS public health providers' willingness to respond in an influenza pandemic. We thus propose using an EPPM-informed assessment of EMS workers' perspectives toward fulfilling their influenza pandemic response roles. METHODOLOGY/PRINCIPAL FINDINGS: We administered an EPPM-informed snapshot survey about attitudes and beliefs toward pandemic influenza response, to a nationally representative, stratified random sample of 1,537 U.S. EMS workers from May-June 2009 (overall response rate: 49%. Of the 586 respondents who met inclusion criteria (currently active EMS providers in primarily EMS response roles, 12% indicated they would not voluntarily report to duty in a pandemic influenza emergency if asked, 7% if required. A majority (52% indicated their unwillingness to report to work if risk of disease transmission to family existed. Confidence in personal safety at work (OR = 3.3 and a high threat/high efficacy ("concerned and confident" EPPM profile (OR = 4.7 distinguished those who were more likely to voluntarily report to duty. Although 96% of EMS workers indicated that they would probably or definitely report to work if they were guaranteed a pandemic influenza vaccine, only 59% had received an influenza immunization in the preceding 12 months. CONCLUSIONS/SIGNIFICANCE: EMS workers' response willingness gaps pose a substantial challenge to prehospital surge capacity in an influenza pandemic. "Concerned and confident" EMS workers are more than four times as likely to fulfill pandemic influenza response expectations. Confidence in workplace safety is a positively influential modifier of their response willingness. These findings can inform

  4. MORBIDITY AND MORTALITY AMONG EMERGENCY WORKERS OF THE CHERNOBYL ACCIDENT: ASSESSMENT OF RADIATION RISKS FOR THE FOLLOW-UP PERIOD OF 1992-2008

    Directory of Open Access Journals (Sweden)

    V. K. Ivanov

    2011-01-01

    Full Text Available Morbidity and mortality among emergency workers of the Chernobyl accident for the follow- up period of 199Morbidity and mortality among the emergency workers of the Chernobyl accident for the follow-up period of 1992-2008 is analyzed in the article. The cohort consists of 47141 emergency workers of 1986-1987. Radiation risks for cancer morbidity (ERR/Gy is 0.76; 95% CI: 0.19; 1.42, p-value=0008 and cancer mortality (ERR/Gy is 0.95; 95% CI: 0.19; 1.89, p-value=0.01 are statistically significant. Radiation risk for vascular diseases is assessed as well.

  5. Assessment of air pollution and its effects on the health status of the workers in beam rolling mills factory (Iran National Steel Industrial Group from Ahvaz-Iran

    Directory of Open Access Journals (Sweden)

    Rafiei Masoud

    2009-01-01

    Full Text Available Background: Air pollutants of iron- and steel-making operations have historically been an environmental and health hazard. These pollutants include gaseous substances such as sulfur oxide, nitrogen dioxide, and carbon monoxide. The Iran National Steel Industrial Group beam rolling mills factory has two production lines viz. line 630 and line 650, with different beam production capabilities and is capable of producing different types of beams. Materials and Methods: A retrospective cross-sectional study on 400 workers in different exposure levels to environmental pollution was performed during 2005 to determine the mean value of respirable particulate matter (RPM concentrations and its effects on the health status of workers. To elicit information regarding the health status of the worker, the National Institute for Occupational Safety and Health standard questionnaire was used. Fisher′s exact test was performed to assess the relative risk (RR of exposure to air pollution on cardiovascular diseases, chest tightness, cough, difficulty in retention, i.e. loss of memory, tension, occupational fatigue, and occupational stress in exposed workers. Results: There was significant difference in RPM pollution level between two product lines. The RR of exposure to air pollution on cardiovascular diseases, chest tightness, cough, difficulty in retention, i.e. loss of memory, tension, occupational fatigue, and occupational stress in exposed workers were 2.78, 2.44, 2.15, 1.92, 1.57, 3.90, and 2.09, respectively.

  6. Comparative assessment of migrant farm worker health in conventional and organic horticultural systems in the United Kingdom.

    Science.gov (United States)

    Cross, Paul; Edwards, Rhiannon T; Hounsome, Barry; Edwards-Jones, Gareth

    2008-02-25

    This study describes the self-reported health and well-being status of field and packhouse workers in UK vegetable horticulture, and tests the null hypothesis that there is no difference in the self-reported health of workers on organic and conventional horticultural farms. The majority of those sampled were migrant workers (93%) from Bulgaria, Latvia, Lithuania, Poland, Russia and the Ukraine. More than 95% of the respondents were aged 18-34 and recruited through university agricultural faculties in East European or employed via UK agencies. The health of 605 farm workers (395 males and 210 females) was measured through the use of four standard health instruments. Farm workers' health was significantly poorer than published national norms for three different health instruments (Short Form 36, EuroQol EQ-5D and the Visual Analogue Scale). There were no significant differences in the health status of farm workers between conventional and organic farms for any of these three instruments. However, organic farm workers scored higher on a fourth health instrument the Short Depression Happiness Scale (SDHS) indicating that workers on organic farms were happier than their counterparts working on conventional farms. Multiple regression analysis suggested that the difference in the SDHS score for organic and conventional farms is closely related to the range and number of tasks the workers performed each day. These findings suggest that a great deal of improvement in the self-reported health of farmers will need to occur before organic farms meet the requirements of the 'Principle of Health' as described by IFOAM. Ensuring that farm workers have a varied range of tasks could be a cost effective means of improving self-reported health status in both organic and conventional farming systems.

  7. Worker Participation

    Science.gov (United States)

    Shepherd, W. F.

    1973-01-01

    The philosophy and workability of the concept of worker participation in management decisions is discussed in the context of British society. It is recommended that four interests be represented in any kind of Workers' Council: management, workers, shareholders, and consumers. (AG)

  8. Prevalence and Assessment of Clinical Management of Sexually Transmitted Infections among Female Sex Workers in Two Cities of India

    Directory of Open Access Journals (Sweden)

    A. Das

    2011-01-01

    Full Text Available Objective. Control of sexually transmitted infections (STIs among female sex workers (FSWs is an important strategy to reduce HIV transmission. A study was conducted to determine the prevalence and assess the current clinical management of STIs in India. Methods. FSWs attending three clinics for regular checkups or symptoms were screened for study eligibility. A behavioral questionnaire was administered, clinical examination performed, and laboratory samples collected. Results. 417 study participants reported a mean number of 4.9 (SD 3.5 commercial clients in the last week. 14.6% reported anal sex in the last three months. Consistent condom use with commercial and regular partners was 70.1% and 17.5%, respectively. The prevalence of gonorrhea was 14.1%, chlamydia 16.1%, and trichomoniasis 31.1% with a third of all infections being asymptomatic. Syphilis seropositivity was 10.1%. Conclusions. At study sites, presumptive treatment for gonorrhea, chlamydia, and syphilis screening should continue. Presumptive treatment for trichomoniasis should be considered. Consistent condom use and partner treatment need to be reemphasized.

  9. Thermal Comfort Assessment-A Study Toward Workers’ Satisfaction in a Low Energy Office Building

    Directory of Open Access Journals (Sweden)

    Mohd Nafiz Shaharon

    2012-01-01

    Full Text Available Problem statement: The government of Malaysia has raised their concerns towards the issue of workers comfort and workspace quality in a Low Energy Office (LEO building. New energy efficient building concepts and technologies require a revision of comfort standards, to create a suitable thermal condition in avoiding occupant dissatisfaction, adverse effect on their productivity and overall building performance. Approach: Assessment was conducted using Babuc-A (Portable air quality monitor and sets of questionnaire adapted from ASHRAE-2004 were 99 respondents selected using a stratified random sampling. Results: This study shows that the thermal comfort zone temperature was identified to be within the range of 21.6-23.6°C and relative humidity of 42-54%. Conclusion: The results suggested that the thermal condition was in the acceptable range of ISO7730 and a lower room temperature was preferred by Malaysian in an office environment compared with the temperature criteria cited in ASHRAE-55. To create an optimum comfortable workplace, temperature between 20-26°C and relative humidity between 40-60% must be maintained. Adequate ventilation must be provided at the minimum rate of 10 l/s of fresh air per person for general office space or every 10 m2 of floor space.

  10. Fluorimetric method for determination of Beryllium; Determinazione fluorimetrica del berillio

    Energy Technology Data Exchange (ETDEWEB)

    Sparacino, N.; Sabbioneda, S. [ENEA, Centro Ricerche Saluggia, Vercelli (Italy). Dip. Energia

    1996-10-01

    The old fluorimetric method for the determination of Beryllium, based essentially on the fluorescence of the Beryllium-Morine complex in a strongly alkaline solution, is still competitive and stands the comparison with more modern methods or at least three reasons: in the presence of solid or gaseous samples (powders), the times necessary to finalize an analytic determination are comparable since the stage of the process which lasts the longest is the mineralization of the solid particles containing Beryllium, the cost of a good fluorimeter is by far Inferior to the cost, e. g., of an Emission Spectrophotometer provided with ICP torch and magnets for exploiting the Zeeman effect and of an Atomic absorption Spectrophotometer provided with Graphite furnace; it is possible to determine, fluorimetrically, rather small Beryllium levels (about 30 ng of Beryllium/sample), this potentiality is more than sufficient to guarantee the respect of all the work safety and hygiene rules now in force. The study which is the subject of this publication is designed to the analysis procedure which allows one to reach good results in the determination of Beryllium, chiefly through the control and measurement of the interference effect due to the presence of some metals which might accompany the environmental samples of workshops and laboratories where Beryllium is handled, either at the pure state or in its alloys. The results obtained satisfactorily point out the merits and limits of this analytic procedure.

  11. Monitoring and assessment of individual doses of occupationally exposed workers due to intake of radionuclides

    International Nuclear Information System (INIS)

    Monitoring and estimation of individual intakes of radionuclides can be complex. Doses of intakes cannot be measured directly, however must be assessed from the monitoring data of the individual. The individual monitoring data includes whole body counting, excretion analysis (urine or faecal). In the estimation of these data requires that the assessor makes assumptions about the exposure scenario, including the pattern and mode of radionuclide intake. Also physicochemical characteristics of the material involved and the period of time between exposure and measurement. This project report seeks to provide some underlying guidance on monitoring programmes and data interpretation using case study. In this present study the committed effective dose (CED) 1.20mSv exceeded the recording level (i.e. 1mSv) however it was below the investigation level (i.e. 2mSv). The present study recommends that as an essential part in internal dosimetry, specialists be capable of recognizing conditions warranting follow-up bioassay and dose evaluation. Personnel should be familiar with the relevant internal dosimetry literature and the recommendations of national and international scientific organizations with regard to internal dose. (au)

  12. Assessment of the labor market experiences of CETA-trained solar workers

    Energy Technology Data Exchange (ETDEWEB)

    Burns, B.A.; Mason, B.; Mikasa, G.Y.

    1980-12-01

    This study assessed solar training offered by CETA-funded programs and labor market experiences of program graduates. The initial research was restricted to programs within California, because the state is involved in a variety of solar-related activities, including development of jobs and training programs in solar energy. Interviews were conducted with 12 CETA solar training programs and graduates in 1979, in cooperation with California's SolarCal Office. Information on graduates includes demographics, educational and work experience, satisfaction with solar training, types of jobs found, wage levels, and job tenure. Program information includes length, types of training, and the number and kinds of solar systems installed. Results show that major programs problems were: limited funding; shortages of trained instructors; insufficient staff; need for local employment information; need for better defined role for unions; and pressures for high placement rates. The curricula involved general skills, skills specific to solar technologies, and basic job behavior and skills. The training involved both classroom and hands-on experience and was mainly tailored to participants and the local job market. Successful placement of program participants was relatively high; over half the initial job placements involved solar energy. Solar jobs appeared to pay more than nonsolar jobs. Participants generally felt that their training had prepared them adequately for their current work.

  13. Inhibitory effects of beryllium chloride on rat liver microsomal enzymes.

    Science.gov (United States)

    Teixeira, C F; Yasaka, W J; Silva, L F; Oshiro, T T; Oga, S

    1990-04-30

    A single i.v. dose (0.1 mmol Be2+/kg) of beryllium chloride prolonged the duration of pentobarbital-induced sleep and zoxazolamine-induced paralysis, in rats. The effects are correlated with changes of the pharmacokinetic parameters and with the in vitro inhibition of both aliphatic and aromatic hydroxylation of pentobarbital and zoxazolamine. In vitro N-demethylation of meperidine and aminopyrine was partially inhibited while O-demethylation of quinidine was unaffected by liver microsomes of rats pretreated with beryllium salt. The findings give clues that beryllium chloride inhibits some forms of cytochrome P-450, especially those responsible for hydroxylation of substrates, like pentobarbital and zoxazolamine.

  14. Analysis of surface contaminants on beryllium and aluminum windows

    International Nuclear Information System (INIS)

    An effort has been made to document the types of contamination which form on beryllium windows surfaces due to interaction with a synchrotron radiation beam. Beryllium windows contaminated in a variety of ways (exposure to water and air) exhibited surface powders, gels, crystals and liquid droplets. These contaminants were analyzed by electron diffraction, electron energy loss spectroscopy, energy dispersive X-ray spectroscopy and wet chemical methods. Materials found on window surfaces include beryllium oxide, amorphous carbon, cuprous oxide, metallic copper and nitric acid. Aluminum window surface contaminants were also examined. (orig.)

  15. Development of Beryllium Vacuum Chamber Technology for the LHC

    CERN Document Server

    Veness, R; Dorn, C

    2011-01-01

    Beryllium is the material of choice for the beam vacuum chambers around collision points in particle colliders due to a combination of transparency to particles, high specific stiffness and compatibility with ultra-high vacuum. New requirements for these chambers in the LHC experiments have driven the development of new methods for the manufacture of beryllium chambers. This paper reviews the requirements for experimental vacuum chambers. It describes the new beryllium technology adopted for the LHC and experience gained in the manufacture and installation.

  16. Assessing the Impact of Community Engagement Interventions on Health Worker Motivation and Experiences with Clients in Primary Health Facilities in Ghana: A Randomized Cluster Trial

    Science.gov (United States)

    Alhassan, Robert Kaba; Nketiah-Amponsah, Edward; Spieker, Nicole; Arhinful, Daniel Kojo; Rinke de Wit, Tobias F.

    2016-01-01

    Background Health worker density per 1000 population in Ghana is one of the lowest in the world estimated to be 2.3, below the global average of 9.3. Low health worker motivation induced by poor working conditions partly explain this challenge. Albeit the wage bill for public sector health workers is about 90% of domestic government expenditure on health in countries such as Ghana, staff motivation and performance output remain a challenge, suggesting the need to complement financial incentives with non-financial incentives through a community-based approach. In this study, a systematic community engagement (SCE) intervention was implemented to engage community groups in healthcare quality assessment to promote mutual collaboration between clients and healthcare providers, and enhance health worker motivation levels. SCE involves structured use of existing community groups and associations to assess healthcare quality in health facilities. Identified quality gaps are discussed with healthcare providers, improvements made and rewards given to best performing facilities for closing quality care gaps. Purpose To evaluate the effect of SCE interventions on health worker motivation and experiences with clients. Methods The study is a cluster randomized trial involving health workers in private (n = 38) and public (n = 26) primary healthcare facilities in two administrative regions in Ghana. Out of 324 clinical and non-clinical staff randomly interviewed at baseline, 234 (72%) were successfully followed at end-line and interviewed on workplace motivation factors and personal experiences with clients. Propensity score matching and difference-in-difference estimations were used to estimate treatment effect of the interventions on staff motivation. Results Intrinsic (non-financial) work incentives including cordiality with clients and perceived career prospects appeared to be prime sources of motivation for health staff interviewed in intervention health facilities while

  17. Cosmis Lithium-Beryllium-Boron Story

    Science.gov (United States)

    Vangioni-Flam, E.; Cassé, M.

    Light element nucleosynthesis is an important chapter of nuclear astrophysics. Specifically, the rare and fragile light nuclei Lithium, Beryllium and Boron (LiBeB) are not generated in the normal course of stellar nucleosynthesis (except Lithium-7) and are, in fact, destroyed in stellar interiors. This characteristic is reflected in the low abundance of these simple species. Up to recently, the most plausible interpretation was that galactic cosmic rays (GCR) interact with interstellar CNO to form LiBeB. Other origins have been also identified, primordial and stellar (Lithium-7) and supernova neutrino spallation (Lithium-7 and Boron-11). In contrast, Beryllium-9, Boron-10 and Lithium-6 are pure spallative products. This last isotope presents a special interest since the Lithium-7/Lithium-6 ratio has been measured in a few halo stars offering a new constraint on the early galactic evolution. However, in the nineties, new observations prompted astrophysicists to reassess the question. Optical measurements of the beryllium and boron abundances in halo stars have been achieved by the 10 meters KECK telescope and the Hubble Space Telescope. These observations indicate a quasi linear correlation between Be and B vs Fe, at least at low metallicity, unexpected on the basis of GCR scenario, predicting a quadratic relationship. As a consequence, the origin and the evolution of the LiBeB nuclei has been revisited. This linearity implies the acceleration of C and O nuclei freshly synthesized and their fragmentation on the the interstellar Hydrogen and Helium. Wolf-Rayet stars and supernovae via the shock waves induced, are the best candidates to the acceleration of their own material enriched into C and O; so LiBeB is produced independently of the Interstellar Medium chemical composition. Moreover, neutrinos emitted by the newly born neutron stars interacting with the C layer of the supernova could produce specifically Lithium-7 and Boron-11. This process is supported by the

  18. Extraction of beryllium from refractory beryllium oxide with dilute ammonium bifluoride and determination by fluorescence: a multiparameter performance evaluation.

    Science.gov (United States)

    Goldcamp, Michael J; Goldcamp, Diane M; Ashley, Kevin; Fernback, Joseph E; Agrawal, Anoop; Millson, Mark; Marlow, David; Harrison, Kenneth

    2009-12-01

    Beryllium exposure can cause a number of deleterious health effects, including beryllium sensitization and the potentially fatal chronic beryllium disease. Efficient methods for monitoring beryllium contamination in workplaces are valuable to help prevent dangerous exposures to this element. In this work, performance data on the extraction of beryllium from various size fractions of high-fired beryllium oxide (BeO) particles (from bifluoride (ABF) solution were obtained under various conditions. Beryllium concentrations were determined by fluorescence using a hydroxybenzoquinoline fluorophore. The effects of ABF concentration and volume, extraction temperature, sample tube types, and presence of filter or wipe media were examined. Three percent ABF extracts beryllium nearly twice as quickly as 1% ABF; extraction solution volume has minimal influence. Elevated temperatures increase the rate of extraction dramatically compared with room temperature extraction. Sample tubes with constricted tips yield poor extraction rates owing to the inability of the extraction medium to access the undissolved particles. The relative rates of extraction of Be from BeO of varying particle sizes were examined. Beryllium from BeO particles in fractions ranging from less than 32 microm up to 212 microm were subjected to various extraction schemes. The smallest BeO particles are extracted more quickly than the largest particles, although at 90 degrees C even the largest BeO particles reach nearly quantitative extraction within 4 hr in 3% ABF. Extraction from mixed cellulosic-ester filters, cellulosic surface-sampling filters, wetted cellulosic dust wipes, and cotton gloves yielded 90% or greater recoveries. Scanning electron microscopy of BeO particles, including partially dissolved particles, shows that dissolution in dilute ABF occurs not just on the exterior surface but also via accessing particles' interiors due to porosity of the BeO material. Comparison of dissolution kinetics data

  19. Exposure Assessment and Inflammatory Response Among Workers Producing Calcium Carbonate Nanomaterials

    Science.gov (United States)

    Cui, Ling

    . Modification is thought to be the primary emission source. It is discovered nanoparticles in the size range of 20-300nm dominate in this workplace, which consists of 90-98% of particle counts in the respirable fraction. Based on the sampling results from 2012, there was a strong relationship between number concentration in 5-25um range and the respirable mass concentration (r= 0.908); however, no such correlation was found between number concentration in nanoscale and respirable mass (r= 0.018). The deposited surface area in TB (r=0.66) and alveolar region (r=0.46) was modestly correlated with number concentration of particles in the nanoscale. A reduced FEV1 and increased BP were consistently found among medium-mass exposure compared to low-mass exposure, however no statistical significance was found. When comparing the four exposure metrics, we found number concentration and surface area concentration in general produce effects in similar direction, however opposite to mass concentration. Such observation is consistent with the correlation among these exposure metrics. Airway inflammatory responses presented a dose-response relationship using mass as exposure metric. The concentrations of IL1beta (p =0.043) and IL8 (p=0.008) in sputum among high mass-exposure group were statistically greater than that in low-mass exposure group. It suggested the inflammatory responses were associated with mass concentration of inhaled nanoparticle particles, which are mainly made up by agglomerated form of nanoparticles. At current stage, with limited understanding of the toxicological perspective of nanoparticle, a complete exposure assessment in nanoparticle facility needs to be conducted in both bulk- and nano-form.

  20. Investigation of the ion beryllium surface interaction

    Energy Technology Data Exchange (ETDEWEB)

    Guseva, M.I.; Birukov, A.Yu.; Gureev, V.M. [RRC Kurchatov Institute, Moscow (Russian Federation)] [and others

    1995-09-01

    The self -sputtering yield of the Be was measured. The energy dependence of the Be self-sputtering yield agrees well with that calculated by W. Eckstein et. al. Below 770 K the self-sputtering yield is temperature independent; at T{sub irr}.> 870 K it increases sharply. Hot-pressed samples at 370 K were implanted with monoenergetic 5 keV hydrogen ions and with a stationary plasma (flux power {approximately} 5 MW/m{sup 2}). The investigation of hydrogen behavior in beryllium shows that at low doses hydrogen is solved, but at doses {ge} 5x10{sup 22} m{sup -2} the bubbles and channels are formed. It results in hydrogen profile shift to the surface and decrease of its concentration. The sputtering results in further concentration decrease at doses > 10{sup 25}m{sup -2}.

  1. Stellar abundances of beryllium and CUBES

    CERN Document Server

    Smiljanic, R

    2014-01-01

    Stellar abundances of beryllium are useful in different areas of astrophysics, including studies of the Galactic chemical evolution, of stellar evolution, and of the formation of globular clusters. Determining Be abundances in stars is, however, a challenging endeavor. The two Be II resonance lines useful for abundance analyses are in the near UV, a region strongly affected by atmospheric extinction. CUBES is a new spectrograph planned for the VLT that will be more sensitive than current instruments in the near UV spectral region. It will allow the observation of fainter stars, expanding the number of targets where Be abundances can be determined. Here, a brief review of stellar abundances of Be is presented together with a discussion of science cases for CUBES. In particular, preliminary simulations of CUBES spectra are presented, highlighting its possible impact in investigations of Be abundances of extremely metal-poor stars and of stars in globular clusters.

  2. Study of Peak Expiratory Flow Rate as the Assessment of Lung Function in Occupationally Exposed Petrol Pump Workers of Western Maharashtra

    OpenAIRE

    Patil Smita V; Sumangala Patil; Sampada Kanitkar

    2016-01-01

    Background: Fast urbanization trends, rapid industrial growth, globalization, and poor environmental conditions at work places have created a lot of healthrelated issues. Aim and Objectives: The aim of this study is to investigate Peak Expiratory Flow Rate (PEFR) as the assessment of lung function in occupationally exposed petrol pump workers and also check whether PEFR increases or decreases with duration of exposure. Material and Methods: The study was conducted o...

  3. A rapid assessment of a community health worker pilot programme to improve the management of hypertension and diabetes in Emfuleni sub-district of Gauteng Province, South Africa

    OpenAIRE

    Ndou, Tshipfuralo; van Zyl, Greer; Hlahane, Salamina; Goudge, Jane

    2013-01-01

    Background: Non-communicable diseases (NCD) and infectious chronic illnesses are recognised as significant contributing factors to the burden of disease globally, specifically in South Africa, yet clinical management is often poor. The involvement of community health workers (CHWs) in TB and HIV care in South Africa, and other low- and middle-income settings, suggests that they could make an important contribution in the management of NCDs. Objectives: Using a rapid assessment, this study exa...

  4. Geochemistry of beryllium in Bulgarian coals

    Energy Technology Data Exchange (ETDEWEB)

    Eskenazy, Greta M. [Geology Department, University of Sofia ' St. Kl. Ohridski' , Tzar Osvoboditel 15, Sofia 1504 (Bulgaria)

    2006-04-03

    The beryllium content of about 3000 samples (coal, coaly shales, partings, coal lithotypes, and isolated coalified woods) from 16 Bulgarian coal deposits was determined by atomic emission spectrography. Mean Be concentrations in coal show great variability: from 0.9 to 35 ppm for the deposits studied. There was no clear-cut relationship between Be content and rank. The following mean and confidence interval Be values were measured: lignites, 2.6+/-0.8 ppm; sub-bituminous coals, 8.2+/-3.3 ppm; bituminous coals, 3.0+/-1.2 ppm; and anthracites, 19+/-9.0 ppm. The Be contents in coal and coaly shales for all deposits correlated positively suggesting a common source of the element. Many samples of the coal lithotypes vitrain and xylain proved to be richer in Be than the hosting whole coal samples as compared on ash basis. Up to tenfold increase in Be levels was routinely recorded in fusain. The ash of all isolated coalified woods was found to contain 1.1 to 50 times higher Be content relative to its global median value for coal inclusions. Indirect evidence shows that Be occurs in both organic and inorganic forms. Beryllium is predominantly organically bound in deposits with enhanced Be content, whereas the inorganic form prevails in deposits whose Be concentration approximates Clarke values. The enrichment in Be exceeding the coal Clarke value 2.4 to 14.5 times in some of the Bulgarian deposits is attributed to subsynchronous at the time of coal deposition hydrothermal and volcanic activity. (author)

  5. New facility for post irradiation examination of neutron irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Ishitsuka, Etsuo; Kawamura, Hiroshi [Oarai Research Establishment, Ibaraki-Ken (Japan)

    1995-09-01

    Beryllium is expected as a neutron multiplier and plasma facing materials in the fusion reactor, and the neutron irradiation data on properties of beryllium up to 800{degrees}C need for the engineering design. The acquisition of data on the tritium behavior, swelling, thermal and mechanical properties are first priority in ITER design. Facility for the post irradiation examination of neutron irradiated beryllium was constructed in the hot laboratory of Japan Materials Testing Reactor to get the engineering design data mentioned above. This facility consist of the four glove boxes, dry air supplier, tritium monitoring and removal system, storage box of neutron irradiated samples. Beryllium handling are restricted by the amount of tritium;7.4 GBq/day and {sup 60}Co;7.4 MBq/day.

  6. Can Community Health Workers Report Accurately on Births and Deaths? Results of Field Assessments in Ethiopia, Malawi and Mali.

    Directory of Open Access Journals (Sweden)

    Romesh Silva

    Full Text Available Most low-income countries lack complete and accurate vital registration systems. As a result, measures of under-five mortality rates rely mostly on household surveys. In collaboration with partners in Ethiopia, Ghana, Malawi, and Mali, we assessed the completeness and accuracy of reporting of births and deaths by community-based health workers, and the accuracy of annualized under-five mortality rate estimates derived from these data. Here we report on results from Ethiopia, Malawi and Mali.In all three countries, community health workers (CHWs were trained, equipped and supported to report pregnancies, births and deaths within defined geographic areas over a period of at least fifteen months. In-country institutions collected these data every month. At each study site, we administered a full birth history (FBH or full pregnancy history (FPH, to women of reproductive age via a census of households in Mali and via household surveys in Ethiopia and Malawi. Using these FBHs/FPHs as a validation data source, we assessed the completeness of the counts of births and deaths and the accuracy of under-five, infant, and neonatal mortality rates from the community-based method against the retrospective FBH/FPH for rolling twelve-month periods. For each method we calculated total cost, average annual cost per 1,000 population, and average cost per vital event reported.On average, CHWs submitted monthly vital event reports for over 95 percent of catchment areas in Ethiopia and Malawi, and for 100 percent of catchment areas in Mali. The completeness of vital events reporting by CHWs varied: we estimated that 30%-90% of annualized expected births (i.e. the number of births estimated using a FPH were documented by CHWs and 22%-91% of annualized expected under-five deaths were documented by CHWs. Resulting annualized under-five mortality rates based on the CHW vital events reporting were, on average, under-estimated by 28% in Ethiopia, 32% in Malawi, and 9% in

  7. Assessment of Chlamydia psittaci Shedding and Environmental Contamination as Potential Sources of Worker Exposure throughout the Mule Duck Breeding Process.

    Science.gov (United States)

    Hulin, V; Bernard, P; Vorimore, F; Aaziz, R; Cléva, D; Robineau, J; Durand, B; Angelis, L; Siarkou, V I; Laroucau, K

    2015-12-28

    Chlamydia psittaci is an obligate intracellular bacterium responsible for avian chlamydiosis, otherwise known as psittacosis, a zoonotic disease that may lead to severe atypical pneumonia. This study was conducted on seven mule duck flocks harboring asymptomatic birds to explore the circulation and persistence of C. psittaci during the entire breeding process and assess the potential sources of worker exposure. Cloacal swabs and air samples were taken on each occasion requiring humans to handle the birds. In parallel, environmental samples, including dust, water, and soil, were collected. Specific real-time PCR analyses revealed the presence of C. psittaci in all flocks but with three different shedding patterns involving ducks about the age of 4, 8, and 12 weeks with heavy, moderate, and low excretion levels, respectively. Air samples were only positive in flocks harboring heavy shedders. Dust in flocks with heavy or moderate shedders carried chlamydial loads strongly associated with the loads detected in avian and soil samples. Environmental contamination, significantly correlated with shedding dynamics, was considered to be the most probable source of exposure. The high prevalence of bacteriophage Chp1 in all flocks, mostly jointly present with chlamydia, suggests an important factor in C. psittaci persistence, thus creating a greater risk for humans. A survey conducted in these flocks regarding farming practices and activities showed that disinfection seems to be the most promising practice for reducing C. psittaci prevalence in ducks and that the place and the duration of action during operations seem to be potential risk factors. Strict adherence to good practices is strongly recommended.

  8. The beryllium production at Ulba metallurgical plant (Ust-Kamenogrsk, Kazakhstan)

    Energy Technology Data Exchange (ETDEWEB)

    Dvinskykh, E.M.; Savchuk, V.V.; Tuzov, Y.V. [Ulba Metallurgical Plant (Zavod), Ust-Kamenogorsk, Abay prospect 102 (Kazakhstan)

    1998-01-01

    The Report includes data on beryllium production of Ulba metallurgical plant, located in Ust-Kamenogorsk (Kazakhstan). Beryllium production is showed to have extended technological opportunities in manufacturing semi-products (beryllium ingots, master alloys, metallic beryllium powders, beryllium oxide) and in production of structural beryllium and its parts. Ulba metallurgical plant owns a unique technology of beryllium vacuum distillation, which allows to produce reactor grades of beryllium with a low content of metallic impurities. At present Ulba plant does not depend on raw materials suppliers. The quantity of stored raw materials and semi-products will allow to provide a 25-years work of beryllium production at a full capacity. The plant has a satisfactory experience in solving ecological problems, which could be useful in ITER program. (author)

  9. Beryllium nitride thin film grown by reactive laser ablation

    OpenAIRE

    G. Soto; Diaz, J.A.; Machorro, R.; Reyes-Serrato, A.; de la Cruz, W.

    2001-01-01

    Beryllium nitride thin films were grown on silicon substrates by laser ablating a beryllium foil in molecular nitrogen ambient. The composition and chemical state were determined with Auger (AES), X-Ray photoelectron (XPS) and energy loss (EELS) spectroscopies. A low absorption coefficient in the visible region, and an optical bandgap of 3.8 eV, determined by reflectance ellipsometry, were obtained for films grown at nitrogen pressures higher than 25 mTorr. The results show that the reaction ...

  10. 10 CFR 850.21 - Hazard assessment.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Hazard assessment. 850.21 Section 850.21 Energy DEPARTMENT OF ENERGY CHRONIC BERYLLIUM DISEASE PREVENTION PROGRAM Specific Program Requirements § 850.21 Hazard... must conduct a beryllium hazard assessment that includes an analysis of existing conditions,...

  11. Determination of beryllium by using X-ray fluorescence spectrometry.

    Science.gov (United States)

    Zawisza, Beata

    2008-03-01

    X-ray fluorescence spectrometry method is subject to certain difficulties and inconveniences for the elements having the atomic number 9 or less. These difficulties become progressively more severe as the atomic number decreases, and are quite serious for beryllium, which is practically indeterminable directly by XRF. Therefore, an indirect determination of beryllium that is based on the evaluation of cobalt in the precipitate is taken into consideration. In the thesis below, there is a description of a new, simple, and precise method by selective precipitation using hexamminecobalt(III) chloride and ammonium carbonate-EDTA solution as a complexing agent for the determining of a trace amount of beryllium using X-ray fluorescence spectrometry. The optimum conditions for [Co(NH(3))(6)][Be(2)(OH)(3)(CO(3))(2)(H(2)O)(2)].(3)H(2)O complex formation were studied. The complex was collected on the membrane filter, and the Co Kalpha line was measured by XRF. The method presents the advantages of the sample preparation and the elimination of the matrix effects due to the thin film obtained. The detection limit of the proposed method is 0.2 mg of beryllium. The method was successfully applied to beryllium determination in copper/ beryllium/cobalt alloys.

  12. Beryllium pressure vessels for creep tests in magnetic fusion energy

    International Nuclear Information System (INIS)

    Beryllium has interesting applications in magnetic fusion experimental machines and future power-producing fusion reactors. Chief among the properties of beryllium that make these applications possible is its ability to act as a neutron multiplier, thereby increasing the tritium breeding ability of energy conversion blankets. Another property, the behavior of beryllium in a 14-MeV neutron environment, has not been fully investigated, nor has the creep behavior of beryllium been studied in an energetic neutron flux at thermodynamically interesting temperatures. This small beryllium pressure vessel could be charged with gas to test pressures around 3, 000 psi to produce stress in the metal of 15,000 to 20,000 psi. Such stress levels are typical of those that might be reached in fusion blanket applications of beryllium. After contacting R. Powell at HEDL about including some of the pressure vessels in future test programs, we sent one sample pressure vessel with a pressurizing tube attached (Fig. 1) for burst tests so the quality of the diffusion bond joints could be evaluated. The gas used was helium. Unfortunately, budget restrictions did not permit us to proceed in the creep test program. The purpose of this engineering note is to document the lessons learned to date, including photographs of the test pressure vessel that show the tooling necessary to satisfactorily produce the diffusion bonds. This document can serve as a starting point for those engineers who resume this task when funds become available

  13. Exposure assessment of workers to airborne PCDD/Fs, PCBs and PAHs at an electric arc furnace steelmaking plant in the UK.

    Science.gov (United States)

    Aries, Eric; Anderson, David R; Fisher, Raymond

    2008-06-01

    Occupational exposure studies were undertaken at a UK electric arc furnace (EAF) steelmaking plant to investigate the exposure of workers via inhalation to dioxins, polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs) including benzo[a]pyrene (B[a]P). Surveys were undertaken in areas including the melting shop, the casting department and a furnace control cabin. The highest concentrations of dioxins and PCBs were found inside the melting shop nearby EAFs, whereas dioxin and PCB concentrations in the casting department and inside the control cabin were significantly lower. Risk characterization was carried out by comparing the daily intake of dioxins and PCBs through inhalation with the recommended tolerable daily intake (TDI). Health risk assessments were also carried out by combining exposure data with inhalation cancer potency factors to quantify the cancer risk. For the most exposed category of workers (melting shop workers), the estimated daily intake via inhalation was 0.35 pg WHO-TEQ kg(-1) body weight (bw) in the worst case scenario. Considering that the average UK adult exposure to dioxins from the diet is 1.8 pg WHO-TEQ kg(-1) bw day(-1), the results indicated that the estimated daily intake of dioxins via inhalation at the EAF would not result in the recommended range of the TDI (1-4 pg WHO-TEQ kg(-1) bw day(-1)) being exceeded. Cancer risks for a 40-year occupational exposure period were determined by multiplying the inhalation dose by the inhalation cancer potency factor for 2,3,7,8-tetrachlorodibenzo-p-dioxin. For melting shop workers, cancer risks from exposure to dioxins and PCBs ranged from 2.05 x 10(-5) to 7.54 x 10(-5). Under most regulatory programmes, excess cancer risks between 1.0 x 10(-4) and 1.0 x 10(-6) indicate an acceptable range of excess cancer risk, suggesting a limited risk from dioxin exposure for workers in the EAF plant. For the calculation of excess cancer risks, no account has been taken of the protection

  14. Combined exposure of F344 rats to beryllium metal and plutonium-239 dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Finch, G.L.; Carlton, W.W.; Rebar, A.H. [Purdue Univ., Lafayette, IN (United States)] [and others

    1995-12-01

    Nuclear weapons industry workers have the potential for inhalation exposures to plutonium (Pu) and other agents, such as beryllium (Be) metal. The purpose of this ongoing study is to investigate potential interactions between Pu and Be in the production of lung tumors in rats exposed by inhalation to particles of {sup 239}PuO{sub 2}, Be metal, or these agents in combination. Inhaled Pu deposited in the lung delivers high-linear-energy transfer, alpha-particle radiation and is known to induce pulmonary cancer in laboratory animals. Although the epidemiological evidence implicating Be in the induction of human lung cancer is weak and controversial, various studies in laboratory animals have demonstrated the pulmonary carcinogenicity of Be. As a result, Be is classified as a suspect human carcinogen in the United STates and as a demonstrated human carcinogen by the International Agency for Research on Cancer. This study is in progress.

  15. An assessment of sex work in Swaziland: barriers to and opportunities for HIV prevention among sex workers.

    Science.gov (United States)

    Chipamaunga, Shalote; Muula, Adamson S; Mataya, Ronald

    2010-10-01

    The HIV situation in virtually all southern African countries is a generalised epidemic. Despite the fact that almost all adult age and social groups have high HIV prevalence estimates, sex workers are disproportionally affected, with prevalence estimates higher than the general population. In a qualitative study of 61 male and female sex workers in Swaziland, we found that while poverty drove many into sex work, others reported motivations of pleasure or "sensation seeking", and freedoms from the burden of marriage as perceived benefits of sex work. We also found that penile-vaginal sex was not universal in male-female sexual encounters; and motivation by sex workers for non-condom use included intention to earn more money from unprotected sex, desire for sexual pleasure, and not having time to use condoms. Many sex workers expressed doubts over an alternative lifestyle, even if that change afforded them money to meet their daily necessities. The findings from this study suggest that treating sex workers as a homogenous group that is driven into, or maintain sex work only because of poverty may be problematic, and could hamper HIV-relevant interventions aimed at reducing their vulnerability to sexually transmitted infections. PMID:21409304

  16. Beryllium data base for in-pile mockup test on blanket of fusion reactor, (1)

    International Nuclear Information System (INIS)

    Beryllium has been used in the fusion blanket designs with ceramic breeder as a neutron multiplier to increase the net tritium breeding ratio (TBR). The properties of beryllium, that is physical properties, chemical properties, thermal properties, mechanical properties, nuclear properties, radiation effects, etc. are necessary for the fusion blanket design. However, the properties of beryllium have not been arranged for the fusion blanket design. Therefore, it is indispensable to check and examine the material data of beryllium reported previously. This paper is the first one of the series of papers on beryllium data base, which summarizes the reported material data of beryllium. (author)

  17. Assess workers' needs and preferences first before planning a physical fitness programme: findings from a polytechnic institute in Singapore.

    Science.gov (United States)

    Wong, M L; Koh, D; Lee, M H

    1998-01-01

    Workplace physical fitness programmes are usually poorly attended because the activities do not meet workers' needs. We investigated leisure-time physical activity and its relation to sociodemographic characteristics and cardiovascular risk factors in a polytechnic institute in Singapore before planning a physical fitness programme. Low leisure-time physical activity (defined as no activity or engaging in physical activity less than once per week) was more prevalent among older women, married workers, smokers and men with unhealthy dietary habits. The type of physical activity varied with age and gender, with a preference for walking by women and older men and jogging by younger men. Low physical activity was significantly associated with sickness absence and self-reported stress in women and higher values of triglycerides and low density lipoprotein cholesterol in men. This survey helps to identify target groups for physical fitness programmes and determine leisure-time physical activities specific to workers' preferences by age and gender. PMID:9604471

  18. Beryllium Health and Safety Committee Data Reporting Task Force White Paper #2 -- Uses of Uncensored Data

    Energy Technology Data Exchange (ETDEWEB)

    MacQueen, D H

    2007-10-10

    On December 8, 1999, the Department of Energy (DOE) published Title 10 CFR 850 (hereafter referred to as the Rule) to establish a chronic beryllium disease prevention program (CBDPP) to: (1) reduce the number of workers currently exposed to beryllium in the course of their work at DOE facilities managed by DOE or its contractors; (2) minimize the levels of, and potential for, exposure to beryllium; and (3) establish medical surveillance requirements to ensure early detection of the disease. On January 4, 2001, DOE issued DOE G 440.1-7A, Implementation Guide for use with 10 CFR 850, Chronic Beryllium Disease Prevention Program, to assist line managers in meeting their responsibilities for implementing the CBDPP. That guide describes methods and techniques that DOE considers acceptable in complying with the Rule. In 2005 a draft DOE Technical Standard ''Management of Items and Areas Containing Low Levels of Beryllium'' (SAFT 0103; hereafter referred to as the ''TS'') was circulated for comment (http://www.hss.energy.gov/NuclearSafety/techstds/tsdrafts/saft-0103.pdf). DOE technical standards are voluntary consensus standards developed when industry standards do not exist (see http://www.hss.energy.gov/NuclearSafety/techstds/index.html for more information). DOE does not require its field elements to implement DOE technical standards, but field elements may choose to adopt these standards to meet specific needs. This beryllium TS is intended to provide best practices and lessons learned for manageing items and areas that contain low levels of beryllium, which has been a costly and technically challenging component of CBDPPs. The TS is also intended to provide guidance for determining if the Rule's housekeeping and release criteria are met. On challenge the TS addressed was the statistical interpretation of data sets with non-detected results, a topic for which no strong consensus exists. Among the many comments on the draft

  19. Radiological assessment of NORM industries in Ireland-radiation doses to workers and members of the public

    International Nuclear Information System (INIS)

    only those industries with potential NORM issues were first published by the European Commission in 1997 and were followed by more specific guidance documents covering particular aspects of NORM: building materials, remediation of contaminated sites, NORM effluents and discharges, waste types produced by industries dealing with special metal and ceramics and NORM waste management and treatment options. Countries located outside Europe may follow and/or implement the International Atomic Energy Agency (IAEA) Safety Standards requirements. As far as the identification of work activities involving NORM is concerned, the IAEA has equally produced a number of important and very helpful documents in the recent years, complementary to those published by the EC which capture the essential aspects of the approach advocated by the IAEA to identify NORM industries. Four large industries operating in Ireland and dealing with NORM were prioritised and investigated to determine the level of radiation to which workers and members of the public were exposed as a result of their work practices: the peat-fired power production, the coal-fired power production, the extraction of natural gas and the bauxite refining for the production of alumina. In each case, a thorough examination of the industrial process has been carried out to identify the potential radiation exposure situations arising from the occurrance of NORM at the different stages of the respective process. At the core of our assessment methodology, the following aspects were targeted. The potential for enhancement of radionuclide concentrations above their natural levels in products, by-products, residues and waste. Their availability to be released into the biosphere, due to physicochemical changes during processing or due to the method used to manage the residues and the waste produced. Occupational radiation doses were estimated based on field measurements and analysis of samples collected onsite. For particular scenarios

  20. Assessing Worker and Environmental Chemical Exposure Risks at an e-Waste Recycling and Disposal Site in Accra, Ghana

    Directory of Open Access Journals (Sweden)

    Jack Caravanos

    2011-01-01

    Conclusions. The Agbogbloshie e-waste recycling/disposal site in Accra, Ghana revealed an area with extensive lead contamination in both ambient air and topsoil. Given the urban nature of this site e as well as the large adjacent food distribution market, the potential for human health impact is substantial both to workers and local residents.

  1. Assessment of the Utilization of HIV Interventions by Sex Workers in Selected Brothels in Bangladesh: An Exploratory Study

    Science.gov (United States)

    Huq, Nafisa Lira; Chowdhury, Mahbub Elahi

    2012-01-01

    In this qualitative study of brothel-based Female Sex Workers (FSWs), the authors explored factors that influence safe sex practices of FSWs within an integrated HIV intervention. Qualitative methods, including focus group discussions (FGDs), in-depth interviews and key informant interviews were applied in four brothels in Bangladesh. Young and…

  2. The work compatibility improvement framework: an assessment of the worker-work environment interaction in the manufacturing sector.

    Science.gov (United States)

    Genaidy, Ash M; Rinder, Magda M; A-Rehim, Amal D

    2008-08-01

    The manufacturing sector in the US is challenged by high health care costs and shortage of qualified workers, which are largely attributed to the degree of fit between the worker and work environment. In this regard, a healthy worker-work environment interface is a necessary and sufficient condition for the containment of health care costs and the retaining/attraction of highly qualified knowledge workers and should be based on the principles of optimum physical, cognitive and emotional health for the workers. In prior research, the Work Compatibility Improvement Framework (WCIF) was introduced as a vehicle to address these issues and was defined as the identification, improvement and maintenance of the well-being characteristics of the workforce and its interaction with the work environment through the application of engineering, medicine, management and human sciences methodologies, technologies and best practices. This paper advances WCIF by examining its applications in manufacturing with regard to the evaluation of working conditions impacting musculoskeletal/stress outcome measures. A study was conducted in a machining department of a bag packaging manufacturer in the Midwest of the United States. The work tasks were planned and executed with regard to the following aims: (1) to compute work compatibility as a function of work demands and energisers; (2) to establish whether the prevalence of musculoskeletal/stress disorders increases with a decrease in the quality of worker-work environment interface in terms of work compatibility level and other work factors such as shift and job category. A major finding is that a 'poor' work environment (a function of all work domains) results in musculoskeletal/stress disorders that are 105% and 67% higher than those for a 'good' work environment. The evening shift exhibited the poorest compatibility followed by the night shift relative to the day shift. Application of the work compatibility approach demonstrated the

  3. Development of Interatomic Potentials for Beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Bjorkas, C.; Juslin, N.; Nordlund, K. [Accelerator Laboratory, University of Helsinki, P.O. Box 43, FIN-00014 Helsinki (Finland); Erhart, P. [Lawrence Livermore National Laboratory, Livermore, AK (United States); Henriksson, K. [Royal Institute of Technology, Stockholm (Sweden)

    2007-07-01

    Full text of publication follows: To be able to benefit from fusion as a clean and safe power source, we need a comprehensive understanding of the dynamic region of a fusion reactor. Knowing the interplay between the fuel plasma and the reactor components, such as the first wall and the divertor, one can minimize the resulting degradation. The atom-level mechanisms behind the reactions, (e.g. erosion and redeposition) are, however, not accessible to experiments. Hence, computational methods, including molecular dynamics (MD) simulations, are needed. The interactions in a system of particles are within MD described by an interatomic potential. The study of reactor processes requires models for the mixed interaction between the first wall and divertor materials beryllium, carbon and tungsten, as well as for the interaction of these with hydrogen. The absence of proper models for the Be system motivated us to develop potentials for pure Be, Be-C, Be-W and Be-H. We present a Tersoff-like bond order potential for pure Be and the same formalism applied to Be-C and Be-H. The performance of the potentials is discussed and an outlook for the remaining potential is also given. (authors)

  4. Beryllium abundances in stars hosting giant planets

    CERN Document Server

    Santos, N C; Israelian, G; Mayor, M; Rebolo, R; García-Gíl, A; Pérez de Taoro, M R; Randich, S

    2002-01-01

    We have derived beryllium abundances in a wide sample of stars hosting planets, with spectral types in the range F7V-K0V, aimed at studying in detail the effects of the presence of planets on the structure and evolution of the associated stars. Predictions from current models are compared with the derived abundances and suggestions are provided to explain the observed inconsistencies. We show that while still not clear, the results suggest that theoretical models may have to be revised for stars with Teff<5500K. On the other hand, a comparison between planet host and non-planet host stars shows no clear difference between both populations. Although preliminary, this result favors a ``primordial'' origin for the metallicity ``excess'' observed for the planetary host stars. Under this assumption, i.e. that there would be no differences between stars with and without giant planets, the light element depletion pattern of our sample of stars may also be used to further investigate and constraint Li and Be deple...

  5. Electronic band structure of beryllium oxide

    CERN Document Server

    Sashin, V A; Kheifets, A S; Ford, M J

    2003-01-01

    The energy-momentum resolved valence band structure of beryllium oxide has been measured by electron momentum spectroscopy (EMS). Band dispersions, bandwidths and intervalence bandgap, electron momentum density (EMD) and density of occupied states have been extracted from the EMS data. The experimental results are compared with band structure calculations performed within the full potential linear muffin-tin orbital approximation. Our experimental bandwidths of 2.1 +- 0.2 and 4.8 +- 0.3 eV for the oxygen s and p bands, respectively, are in accord with theoretical predictions, as is the s-band EMD after background subtraction. Contrary to the calculations, however, the measured p-band EMD shows large intensity at the GAMMA point. The measured full valence bandwidth of 19.4 +- 0.3 eV is at least 1.4 eV larger than the theory. The experiment also finds a significantly higher value for the p-to-s-band EMD ratio in a broad momentum range compared to the theory.

  6. Interaction of beryllium and hydrogen isotopes

    International Nuclear Information System (INIS)

    It has been considered that in the plasma nuclear fusion experimental devices of magnetic field confinement type, in order to reduce the energy loss due to bremsstrahlung, the use of the plasma-facing materials (PFM) of low atomic number like carbon is indispensable at present. Attention is paid to beryllium which is one of the PFMs, and its effectiveness was rocognized by the practical use in JET. When Be is considered as a PFM, it is necessary to accumulate many data on the diffusion, dissolution, permeation and surface recoupling of hydrogen isotopes, which regulate the recycling and inventory of deuterium and tritium fuel, and the relation of these factors with the physical and chemical states of Be. In this research, as the first phase of understanding the characteristics of Be as a PFM, the change of the surface condition by heating Be was investigated by X-ray photoelectron spectroscopy, and the chemical form of the Be-related substances emitted from the surface by argon or deuterium ion sputtering and their thermal behavior were measured by secondary ion mass spectrometry. The sample, the measurement and the results are reported. The diversified secondary ions of Be, Be cluster, Be oxide, hydroxide, hydride and deuteride were observed by the measurement, and their features are shown. (K.I.)

  7. Steam-chemical reactivity for irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Anderl, R.A.; McCarthy, K.A.; Oates, M.A.; Petti, D.A.; Pawelko, R.J.; Smolik, G.R. [Idaho National Engineering and Environmental Lab., Idaho Falls, ID (United States)

    1998-01-01

    This paper reports the results of an experimental investigation to determine the influence of neutron irradiation effects and annealing on the chemical reactivity of beryllium exposed to steam. The work entailed measurements of the H{sub 2} generation rates for unirradiated and irradiated Be and for irradiated Be that had been previously annealed at different temperatures ranging from 450degC to 1200degC. H{sub 2} generation rates were similar for irradiated and unirradiated Be in steam-chemical reactivity experiments at temperatures between 450degC and 600degC. For irradiated Be exposed to steam at 700degC, the chemical reactivity accelerated rapidly and the specimen experienced a temperature excursion. Enhanced chemical reactivity at temperatures between 400degC and 600degC was observed for irradiated Be annealed at temperatures of 700degC and higher. This reactivity enhancement could be accounted for by the increased specific surface area resulting from development of a surface-connected porosity in the irradiated-annealed Be. (author)

  8. The structure, properties and performance of plasma-sprayed beryllium for fusion applications

    Energy Technology Data Exchange (ETDEWEB)

    Castro, R.G.; Stanek, P.W.; Elliott, K.E. [and others

    1995-09-01

    Plasma-spray technology is under investigation as a method for producing high thermal conductivity beryllium coatings for use in magnetic fusion applications. Recent investigations have focused on optimizing the plasma-spray process for depositing beryllium coatings on damaged beryllium surfaces. Of particular interest has been optimizing the processing parameters to maximize the through-thickness thermal conductivity of the beryllium coatings. Experimental results will be reported on the use of secondary H{sub 2} gas additions to improve the melting of the beryllium powder and transferred-arc cleaning to improve the bonding between the beryllium coatings and the underlying surface. Information will also be presented on thermal fatigue tests which were done on beryllium coated ISX-B beryllium limiter tiles using 10 sec cycle times with 60 sec cooldowns and an International Thermonuclear Experimental Reactor (ITER) relevant divertor heat flux slightly in excess of 5 MW/m{sup 2}.

  9. Controlling Beryllium Contaminated Material And Equipment For The Building 9201-5 Legacy Material Disposition Project

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, T. D.; Easterling, S. D.

    2010-10-01

    This position paper addresses the management of beryllium contamination on legacy waste. The goal of the beryllium management program is to protect human health and the environment by preventing the release of beryllium through controlling surface contamination. Studies have shown by controlling beryllium surface contamination, potential airborne contamination is reduced or eliminated. Although there are areas in Building 9201-5 that are contaminated with radioactive materials and mercury, only beryllium contamination is addressed in this management plan. The overall goal of this initiative is the compliant packaging and disposal of beryllium waste from the 9201-5 Legacy Material Removal (LMR) Project to ensure that beryllium surface contamination and any potential airborne release of beryllium is controlled to levels as low as practicable in accordance with 10 CFR 850.25.

  10. Validation of cleaning method for various parts fabricated at a Beryllium facility

    Energy Technology Data Exchange (ETDEWEB)

    Davis, Cynthia M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-12-15

    This study evaluated and documented a cleaning process that is used to clean parts that are fabricated at a beryllium facility at Los Alamos National Laboratory. The purpose of evaluating this cleaning process was to validate and approve it for future use to assure beryllium surface levels are below the Department of Energy’s release limits without the need to sample all parts leaving the facility. Inhaling or coming in contact with beryllium can cause an immune response that can result in an individual becoming sensitized to beryllium, which can then lead to a disease of the lungs called chronic beryllium disease, and possibly lung cancer. Thirty aluminum and thirty stainless steel parts were fabricated on a lathe in the beryllium facility, as well as thirty-two beryllium parts, for the purpose of testing a parts cleaning method that involved the use of ultrasonic cleaners. A cleaning method was created, documented, validated, and approved, to reduce beryllium contamination.

  11. Beryllium processing technology review for applications in plasma-facing components

    Energy Technology Data Exchange (ETDEWEB)

    Castro, R.G.; Jacobson, L.A.; Stanek, P.W.

    1993-07-01

    Materials research and development activities for the International Thermonuclear Experimental Reactor (ITER), i.e., the next generation fusion reactor, are investigating beryllium as the first-wall containment material for the reactor. Important in the selection of beryllium is the ability to process, fabricate and repair beryllium first-wall components using existing technologies. Two issues that will need to be addressed during the engineering design activity will be the bonding of beryllium tiles in high-heat-flux areas of the reactor, and the in situ repair of damaged beryllium tiles. The following review summarizes the current technology associated with welding and joining of beryllium to itself and other materials, and the state-of-the-art in plasma-spray technology as an in situ repair technique for damaged beryllium tiles. In addition, a review of the current status of beryllium technology in the former Soviet Union is also included.

  12. Erosion of beryllium under ITER – Relevant transient plasma loads

    Energy Technology Data Exchange (ETDEWEB)

    Kupriyanov, I.B., E-mail: igkupr@gmail.com [A.A. Bochvar High Technology Research Institute of Inorganic Materials, Rogova St. 5a, 123060 Moscow (Russian Federation); Nikolaev, G.N.; Kurbatova, L.A.; Porezanov, N.P. [A.A. Bochvar High Technology Research Institute of Inorganic Materials, Rogova St. 5a, 123060 Moscow (Russian Federation); Podkovyrov, V.L.; Muzichenko, A.D.; Zhitlukhin, A.M. [TRINITI, Troitsk, Moscow reg. (Russian Federation); Gervash, A.A. [Efremov Research Institute, S-Peterburg (Russian Federation); Safronov, V.M. [Project Center of ITER, Moscow (Russian Federation)

    2015-08-15

    Highlights: • We study the erosion, mass loss/gain and surface structure evolution of Be/CuCrZr mock-ups, armored with beryllium of TGP-56FW grade after irradiation by deuterium plasma heat load of 0.5 MJ/m{sup 2} at 250 °C and 500 °C. • Beryllium mass loss/erosion under plasma heat load at 250 °C is rather small (no more than 0.2 g/m{sup 2} shot and 0.11 μm/shot, correspondingly, after 40 shots) and tends to decrease with increasing number of shots. • Beryllium mass loss/erosion under plasma heat load at 500 °C is much higher (∼2.3 g/m{sup 2} shot and 1.2 μm/shot, correspondingly, after 10 shot) and tends to decrease with increasing the number of shots (∼0.26 g/m{sup 2} pulse and 0.14 μm/shot, correspondingly, after 100 shot). • Beryllium erosion value derived from the measurements of profile of irradiated surface is much higher than erosion value derived from mass loss data. - Abstract: Beryllium will be used as a armor material for the ITER first wall. It is expected that erosion of beryllium under transient plasma loads such as the edge-localized modes (ELMs) and disruptions will mainly determine a lifetime of the ITER first wall. This paper presents the results of recent experiments with the Russian beryllium of TGP-56FW ITER grade on QSPA-Be plasma gun facility. The Be/CuCrZr mock-ups were exposed to up to 100 shots by deuterium plasma streams (5 cm in diameter) with pulse duration of 0.5 ms and heat loads range of 0.2–0.5 MJ/m{sup 2} at different temperature of beryllium tiles. The temperature of Be tiles has been maintained about 250 and 500 °C during the experiments. After 10, 40 and 100 shots, the beryllium mass loss/gain under erosion process were investigated as well as evolution of surface microstructure and cracks morphology.

  13. A Report on the Validation of Beryllium Strength Models

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, Derek Elswick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-02-05

    This report discusses work on validating beryllium strength models with flyer plate and Taylor rod experimental data. Strength models are calibrated with Hopkinson bar and quasi-static data. The Hopkinson bar data for beryllium provides strain rates up to about 4000 per second. A limitation of the Hopkinson bar data for beryllium is that it only provides information on strain up to about 0.15. The lack of high strain data at high strain rates makes it difficult to distinguish between various strength model settings. The PTW model has been calibrated many different times over the last 12 years. The lack of high strain data for high strain rates has resulted in these calibrated PTW models for beryllium exhibiting significantly different behavior when extrapolated to high strain. For beryllium, the α parameter of PTW has recently been calibrated to high precision shear modulus data. In the past the α value for beryllium was set based on expert judgment. The new α value for beryllium was used in a calibration of the beryllium PTW model by Sky Sjue. The calibration by Sjue used EOS table information to model the temperature dependence of the heat capacity. Also, the calibration by Sjue used EOS table information to model the density changes of the beryllium sample during the Hopkinson bar and quasi-static experiments. In this paper, the calibrated PTW model by Sjue is compared against experimental data and other strength models. The other strength models being considered are a PTW model calibrated by Shuh- Rong Chen and a Steinberg-Guinan type model by John Pedicini. The three strength models are used in a comparison against flyer plate and Taylor rod data. The results show that the Chen PTW model provides better agreement to this data. The Chen PTW model settings have been previously adjusted to provide a better fit to flyer plate data, whereas the Sjue PTW model has not been changed based on flyer plate data. However, the Sjue model provides a reasonable fit to

  14. A Real-Time Location-Based Services System Using WiFi Fingerprinting Algorithm for Safety Risk Assessment of Workers in Tunnels

    Directory of Open Access Journals (Sweden)

    Peng Lin

    2014-01-01

    Full Text Available This paper investigates the feasibility of a real-time tunnel location-based services (LBS system to provide workers’ safety protection and various services in concrete dam site. In this study, received signal strength- (RSS- based location using fingerprinting algorithm and artificial neural network (ANN risk assessment is employed for position analysis. This tunnel LBS system achieves an online, real-time, intelligent tracking identification feature, and the on-site running system has many functions such as worker emergency call, track history, and location query. Based on ANN with a strong nonlinear mapping, and large-scale parallel processing capabilities, proposed LBS system is effective to evaluate the risk management on worker safety. The field implementation shows that the proposed location algorithm is reliable and accurate (3 to 5 meters enough for providing real-time positioning service. The proposed LBS system is demonstrated and firstly applied to the second largest hydropower project in the world, to track workers on tunnel site and assure their safety. The results show that the system is simple and easily deployed.

  15. Report of a technical evaluation panel on the use of beryllium for ITER plasma facing material and blanket breeder material

    International Nuclear Information System (INIS)

    Beryllium because of its low atomic number and high thermal conductivity, is a candidate for both ITER first wall and divertor surfaces. This study addresses the following: why beryllium; design requirements for the ITER divertor; beryllium supply and unirradiated physical/mechanical property database; effects of irradiation on beryllium properties; tritium issues; beryllium health and safety; beryllium-coolant interactions and safety; thermal and mechanical tests; plasma erosion of beryllium; recommended beryllium grades for ITER plasma facing components; proposed manufacturing methods to produce beryllium parts for ITER; emerging beryllium materials; proposed inspection and maintenance techniques for beryllium components and coatings; time table and costs; and the importance of integrating materials and manufacturing personnel with designers

  16. Report of a technical evaluation panel on the use of beryllium for ITER plasma facing material and blanket breeder material

    Energy Technology Data Exchange (ETDEWEB)

    Ulrickson, M.A. [ed.] [Sandia National Labs., Albuquerque, NM (United States); Manly, W.D. [Oak Ridge National Lab., TN (United States); Dombrowski, D.E. [Brush Wellman, Inc., Cleveland, OH (United States)] [and others

    1995-08-01

    Beryllium because of its low atomic number and high thermal conductivity, is a candidate for both ITER first wall and divertor surfaces. This study addresses the following: why beryllium; design requirements for the ITER divertor; beryllium supply and unirradiated physical/mechanical property database; effects of irradiation on beryllium properties; tritium issues; beryllium health and safety; beryllium-coolant interactions and safety; thermal and mechanical tests; plasma erosion of beryllium; recommended beryllium grades for ITER plasma facing components; proposed manufacturing methods to produce beryllium parts for ITER; emerging beryllium materials; proposed inspection and maintenance techniques for beryllium components and coatings; time table and costs; and the importance of integrating materials and manufacturing personnel with designers.

  17. Experimental studies and modeling of processes of hydrogen isotopes interaction with beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Tazhibaeva, I.L.; Chikhray, Y.V.; Romanenko, O.G.; Klepikov, A.Kh.; Shestakov, V.P.; Kulsartov, T.V. [Science Research Inst. of Experimental and Theoretical Physics of Kazakh State Univ., Almaty (Kazakhstan); Kenzhin, E.A.

    1998-01-01

    The objective of this work was to clarify the surface beryllium oxide influence on hydrogen-beryllium interaction characteristics. Analysis of experimental data and modeling of processes of hydrogen isotopes accumulation, diffusion and release from neutron irradiated beryllium was used to achieve this purpose as well as the investigations of the changes of beryllium surface element composition being treated by H{sup +} and Ar{sup +} plasma glowing discharge. (author)

  18. Computational Predictions of the Beryllium Analogue of Borole, Cp(+), and the Fluorenyl Cation: Highly Stabilized, non-Lewis Acidic Antiaromatic Ring Systems.

    Science.gov (United States)

    Field-Theodore, Terri E; Wilson, David J D; Dutton, Jason L

    2015-08-17

    A computational study of a set of synthetically unknown beryllium-containing rings, anionic analogues of antiaromatic boroles, has been carried out to investigate their structure, stability, and potential reactivity. The results indicate that these compounds should be electronically viable (as assessed from HOMO-LUMO and singlet-triplet gaps) and therefore potential targets for synthesis. In strong contrast with boroles, these beryllium species are predicted to be not Lewis acidic but rather Lewis basic, with reactivity centered on the endocyclic Be-C bond.

  19. Lawrence Livermore Laboratory's beryllium control program for high-explosive test firing bunkers and tables

    International Nuclear Information System (INIS)

    This report on the control program to minimize beryllium levels in Laboratory workplaces includes an outline of beryllium surface, soil, and air levels and an 11-y summary of sampling results from two high-use, high-explosive test firing bunkers. These sampling data and other studies demonstrate that the beryllium control program is functioning effectively

  20. Mayak Worker Dosimetry System 2008 (MWDS-2008): assessment of internal dose from measurement results of plutonium activity in urine.

    Science.gov (United States)

    Khokhryakov, Victor V; Khokhryakov, Valentin F; Suslova, Klara G; Vostrotin, Vadim V; Vvedensky, Vladimir E; Sokolova, Alexandra B; Krahenbuhl, Melinda P; Birchall, Alan; Miller, Scott C; Schadilov, Anatoly E; Ephimov, Alexander V

    2013-04-01

    A new modification of the prior human lung compartment plutonium model, Doses-2005, has been described. The modified model was named "Mayak Worker Dosimetry System-2008" (MWDS-2008). In contrast to earlier models developed for workers at the Mayak Production Association (Mayak PA), the new model more correctly describes plutonium biokinetics and metabolism in pulmonary lymph nodes. The MWDS-2008 also provides two sets of doses estimates: one based on bioassay data and the other based on autopsy data, where available. The algorithm of internal dose calculation from autopsy data will be described in a separate paper. Results of comparative analyses of Doses-2005 and MWDS-2008 are provided. Perspectives on the further development of plutonium dosimetry are discussed.

  1. How do frontline tax workers assess citizen-clients’ trustworthiness? The role of signals and status characteristics

    OpenAIRE

    Raaphorst, Nadine; Groeneveld, Sandra

    2015-01-01

    textabstractWithin the literature on street-level workers’ encounters with citizens it is generally known that bureaucrats’ decision making is partly dependent on the relationship they have with them. Within policy areas that promote notions as trust and responsiveness, bureaucrats’ relationship with citizen-clients becomes even more crucial. Very little is known about what frontline workers deem trustworthy and untrustworthy citizen-clients in the first place, and how they know they have to ...

  2. A skills and needs analysis among social workers assessing alleged child sexual abuse in the Western Cape

    OpenAIRE

    Iffley, Roché Shandré

    2012-01-01

    This study focuses on the skills and needs of forensic social workers, working with alleged child sexual abuse in the Western Cape. Forensic social work is based on specialised knowledge drawn from established principles and their application within proven methodology of training, familiarity with the law, evaluation and objective criteria associated with treatment outcomes. The scope of forensic social work thus includes a specialised skill where human service systems communicate the languag...

  3. A longitudinal study of industrial and clerical workers: incidence of carpal tunnel syndrome and assessment of risk factors.

    Science.gov (United States)

    Gell, Nancy; Werner, Robert A; Franzblau, Alfred; Ulin, Sheryl S; Armstrong, Thomas J

    2005-03-01

    This study followed workers over an extended period of time to identify factors which may influence the onset of Carpal Tunnel Syndrome (CTS). The purpose was to evaluate incidence of CTS and to create a predictive model of factors that play a role in the development of CTS. This prospective study followed 432 industrial and clerical workers over 5.4 years. Incident cases were defined as workers who had no prior history of CTS at baseline testing and were diagnosed with CTS during the follow-up period or at the follow-up screening. On the basis of logistic regression, significant predictors for CTS include baseline median-ulnar peak latency difference, a history of wrist/hand/finger tendonitis, a history of numbness, tingling, burning, and/or pain in the hand, and work above the action level of the peak force and hand activity level threshold limit value. This longitudinal study supports findings from previous cross-sectional studies identifying both work related ergonomic stressors and physical factors as independent risk factors for CTS.

  4. Assessment of work environmental hazard and exposure of a worker utilizing 226Ra in an oncological center

    International Nuclear Information System (INIS)

    Our study presents dosimetric evaluation of activities associated with sealing in glass 72 sources of 226Ra prepared for utilization, and of the effect of an absorbed dose on a worker's select laboratory parameters. During 3 h exposure to 226Ra of activity 31 GBq, it was demonstrated that taking the sources from a bunker in portions only for the time of sealing them in glass, decreases the worker's exposure to the obtained dose from 91.5 mSv to 6 mSv, and additionally used 5 cm shield to 2 mSv. Nine days after the worker's absorption of the radiation dose, we observed in laboratory tests disorders expressed by decreased numbers of white blood cells and neutrophils, decreased activity of antioxidative enzymes in erythrocytes, concentrations of protein thiol groups, vascular endothelial growth factors in serum, and an increase of plasma total antioxidant status level, of insulin-like growth factor I level, and urokinase-type plasminogen activator receptor level in blood serum. (authors)

  5. Estimation of beryllium ground state energy by Monte Carlo simulation

    Energy Technology Data Exchange (ETDEWEB)

    Kabir, K. M. Ariful [Department of Physical Sciences, School of Engineering and Computer Science, Independent University, Bangladesh (IUB) Dhaka (Bangladesh); Halder, Amal [Department of Mathematics, University of Dhaka Dhaka (Bangladesh)

    2015-05-15

    Quantum Monte Carlo method represent a powerful and broadly applicable computational tool for finding very accurate solution of the stationary Schrödinger equation for atoms, molecules, solids and a variety of model systems. Using variational Monte Carlo method we have calculated the ground state energy of the Beryllium atom. Our calculation are based on using a modified four parameters trial wave function which leads to good result comparing with the few parameters trial wave functions presented before. Based on random Numbers we can generate a large sample of electron locations to estimate the ground state energy of Beryllium. Our calculation gives good estimation for the ground state energy of the Beryllium atom comparing with the corresponding exact data.

  6. Photochemical Behavior of Beryllium Complexes with Subporphyrazines and Subphthalocyanines.

    Science.gov (United States)

    Montero-Campillo, M Merced; Lamsabhi, Al Mokhtar; Mó, Otilia; Yáñez, Manuel

    2016-07-14

    Structures of beryllium subphthalocyanines and beryllium subporphyrazines complexes with different substituents are explored for the first time. Their photochemical properties are studied using time-dependent density functional theory calculations and compared to boron-related compounds for which their photochemical activity is already known. These beryllium compounds were found to be thermodynamically stable in a vacuum and present features similar to those of boron-containing analogues, although the nature of bonding between the cation and the macrocycle presents subtle differences. Most important contributions to the main peak in the Q-band region arise from HOMO to LUMO transitions in the case of subphthalocyanines and alkyl subporphyrazine complexes, whereas a mixture of that contribution and a HOMO-2 to LUMO contribution are present in the case of thioalkyl subporphyrazines. The absorption in the visible region could make these candidates suitable for photochemical devices if combined with appropriate donor groups. PMID:26812068

  7. Measurement of the ultracold neutron loss coefficient in beryllium powder

    International Nuclear Information System (INIS)

    The ultracold neutron (UCN) reflection from beryllium powder at different slab thicknesses and different packing densities is measured. The reduced UCN loss coefficient η=(1.75±0.35)x10-4 for thermally untreated beryllium is extracted from experimental data. The formerly obtained experimental results on UCN reflection from beryllium after high temperature annealing are reconsidered. The loss coefficient η at room temperature in this case is obtained to be (6.4±2.5)x10-5, which is an order of magnitude higher than the theoretical one. The extraction of the loss coefficient from the experimental data is based on the modified diffusion theory where albedo reflection depends on packing density

  8. Field-emission spectroscopy of beryllium atoms adsorbed on tungsten

    Energy Technology Data Exchange (ETDEWEB)

    Czyzewski, J.J.; Grzesiak, W.; Krajniak, J. (Politechnika Wroclawska (Poland))

    1981-01-01

    Field emission energy distributions (FEED) have been measured for the beryllium-tungsten (023) adsorption system over the 78-450 K temperature range. A temperature dependence of the normalized half-width, ..delta../d, of FEED peaks changed significantly due to beryllium adsorption; and the curve, ..delta../d vs p, for the Be/W adsorption system was identical in character to the calculated curve based on the free electron model in contrast to the curve for the clean tungsten surface. In the last part of this paper Gadzuk's theory of the resonance-tunneling effect is applied to the beryllium atom on tungsten. Experimental and theoretical curves of the enhancement factor as a function of energy have been discussed.

  9. Force-field parameters for beryllium complexes in amorphous layers.

    Science.gov (United States)

    Emelyanova, Svetlana; Chashchikhin, Vladimir; Bagaturyants, Alexander

    2016-09-01

    Unknown force-field parameters for metal organic beryllium complexes used in emitting and electron transporting layers of OLED structures are determined. These parameters can be used for the predictive atomistic simulations of the structure and properties of amorphous organic layers containing beryllium complexes. The parameters are found for the AMBER force field using a relaxed scan procedure and quantum-mechanical DFT calculations of potential energy curves for specific internal (angular) coordinates in a series of three Be complexes (Bebq2; Be(4-mpp)2; Bepp2). The obtained parameters are verified in calculations of some molecular and crystal structures available from either quantum-mechanical DFT calculations or experimental data. Graphical Abstract Beryllium complexes in amorphous layersᅟ. PMID:27550375

  10. Neutron irradiation behavior of ITER candidate beryllium grades

    Energy Technology Data Exchange (ETDEWEB)

    Kupriyanov, I.B.; Gorokhov, V.A.; Nikolaev, G.N. [A.A.Bochvar All-Russia Scientific Research Inst. of Inorganic Materials (VNIINM), Moscow (Russian Federation); Melder, R.R.; Ostrovsky, Z.E.

    1998-01-01

    Beryllium is one of the main candidate materials both for the neutron multiplier in a solid breeding blanket and for the plasma facing components. That is why its behaviour under the typical for fusion reactor loading, in particular, under the neutron irradiation is of a great importance. This paper presents mechanical properties, swelling and microstructure of six beryllium grades (DshG-200, TR-30, TshG-56, TRR, TE-30, TIP-30) fabricated by VNIINM, Russia and also one - (S-65) fabricated by Brush Wellman, USA. The average grain size of the beryllium grades varied from 8 to 25 {mu}m, beryllium oxide content was 0.8-3.2 wt. %, initial tensile strength was 250-680 MPa. All the samples were irradiated in active zone of SM-3 reactor up to the fast neutron fluence (5.5-6.2) {center_dot} 10{sup 21} cm{sup -2} (2.7-3.0 dpa, helium content up to 1150 appm), E > 0.1 MeV at two temperature ranges: T{sub 1} = 130-180degC and T{sub 2} = 650-700degC. After irradiation at 130-180degC no changes in samples dimensions were revealed. After irradiation at 650-700degC swelling of the materials was found to be in the range 0.1-2.1 %. Beryllium grades TR-30 and TRR, having the smallest grain size and highest beryllium oxide content, demonstrated minimal swelling, which was no more than 0.1 % at 650-700degC and fluence 5.5 {center_dot} 10{sup 21} cm{sup -2}. Tensile and compression test results and microstructure parameters measured before and after irradiation are also presented. (author)

  11. CHAPTER 7. BERYLLIUM ANALYSIS BY NON-PLASMA BASED METHODS

    Energy Technology Data Exchange (ETDEWEB)

    Ekechukwu, A

    2009-04-20

    The most common method of analysis for beryllium is inductively coupled plasma atomic emission spectrometry (ICP-AES). This method, along with inductively coupled plasma mass spectrometry (ICP-MS), is discussed in Chapter 6. However, other methods exist and have been used for different applications. These methods include spectroscopic, chromatographic, colorimetric, and electrochemical. This chapter provides an overview of beryllium analysis methods other than plasma spectrometry (inductively coupled plasma atomic emission spectrometry or mass spectrometry). The basic methods, detection limits and interferences are described. Specific applications from the literature are also presented.

  12. Assessment of Air Pollution and its Effects on Health of Workers of Steel Re-Rolling Mills in Hyderabad

    Directory of Open Access Journals (Sweden)

    Altaf Alam Noonari

    2016-04-01

    Full Text Available The SRRMs (Steel Re-Rolling Mills are being releasing air pollutants in the environment. In order to evaluate their effect on the health of the workers, health and safety issues were analyzed by first measuring the concentrations of SO x (OIxides of Sulphur, NO x (Oxides of Nitrogen, CO (Carbon Monoxide and O2 (Oxygen produced in the three SRRMs located in SITE area Hyderabad. The mean concentration of SO x , NO x and CO were in the order of 0.35, 0.280, 6.333 ppm, respectively, whereas the mean concentration of O 2 was 203.53 thousand ppm. As per results, the concentration ofair pollutants, including SOx and NO x were significantly higher than to the NEQS (National Environmental Quality Standards and NAAQS (National Ambient Air Quality Standards. The concentration ofCO was lower than to the NAAQS, but higher than to the NEQs, while the concentration of O2 was slightly lower than to the standard value. The workers who were exposed to these air pollutants are being suffering from chronic diseases related to breathing and allergies. Moreover, labour staff was lifting heavy loads manually, which causes them to muscular and joint problems. In all the SRRMs under study, the electrical and mechanical equipments were used without any safety. The MSDS were not displayed on the workstations, the housekeeping was inadequate and most of the workers were performing their jobs without personal protective equipment. In addition to these, the other serious issues related to the occupational health and safety were an unhygienic supply of water, higher noise level, placement of explosive cylinders in the open atmosphere and unavailability of the first aid facilities in the Mill premises.

  13. Occupational exposure to airborne nanomaterials: An assessment of worker exposure to aerosolized metal oxide nanoparticles in a semiconductor fab and subfab.

    Science.gov (United States)

    Brenner, Sara A; Neu-Baker, Nicole M; Caglayan, Cihan; Zurbenko, Igor G

    2016-09-01

    This occupational exposure assessment study characterized potential inhalation exposures of workers to engineered nanomaterials associated with chemical mechanical planarization wafer polishing processes in a semiconductor research and development facility. Air sampling methodology was designed to capture airborne metal oxide nanoparticles for characterization. The research team obtained air samples in the fab and subfab areas using a combination of filter-based capture methods to determine particle morphology and elemental composition and real-time direct-reading instruments to determine airborne particle counts. Filter-based samples were analyzed by electron microscopy and energy-dispersive x-ray spectroscopy while real-time particle counting data underwent statistical analysis. Sampling was conducted during worker tasks associated with preventive maintenance and quality control that were identified as having medium to high potential for inhalation exposure based on qualitative assessments. For each sampling event, data was collected for comparison between the background, task area, and personal breathing zone. Sampling conducted over nine months included five discrete sampling series events in coordination with on-site employees under real working conditions. The number of filter-based samples captured was: eight from worker personal breathing zones; seven from task areas; and five from backgrounds. A complementary suite of direct-reading instruments collected data for seven sample collection periods in the task area and six in the background. Engineered nanomaterials of interest (Si, Al, Ce) were identified in filter-based samples from all areas of collection, existing as agglomerates (>500 nm) and nanoparticles (100-500 nm). Particle counts showed an increase in number concentration above background during a subset of the job tasks, but particle counts in the task areas were otherwise not significantly higher than background. Additional data is needed to

  14. Occupational exposure to airborne nanomaterials: An assessment of worker exposure to aerosolized metal oxide nanoparticles in a semiconductor fab and subfab.

    Science.gov (United States)

    Brenner, Sara A; Neu-Baker, Nicole M; Caglayan, Cihan; Zurbenko, Igor G

    2016-09-01

    This occupational exposure assessment study characterized potential inhalation exposures of workers to engineered nanomaterials associated with chemical mechanical planarization wafer polishing processes in a semiconductor research and development facility. Air sampling methodology was designed to capture airborne metal oxide nanoparticles for characterization. The research team obtained air samples in the fab and subfab areas using a combination of filter-based capture methods to determine particle morphology and elemental composition and real-time direct-reading instruments to determine airborne particle counts. Filter-based samples were analyzed by electron microscopy and energy-dispersive x-ray spectroscopy while real-time particle counting data underwent statistical analysis. Sampling was conducted during worker tasks associated with preventive maintenance and quality control that were identified as having medium to high potential for inhalation exposure based on qualitative assessments. For each sampling event, data was collected for comparison between the background, task area, and personal breathing zone. Sampling conducted over nine months included five discrete sampling series events in coordination with on-site employees under real working conditions. The number of filter-based samples captured was: eight from worker personal breathing zones; seven from task areas; and five from backgrounds. A complementary suite of direct-reading instruments collected data for seven sample collection periods in the task area and six in the background. Engineered nanomaterials of interest (Si, Al, Ce) were identified in filter-based samples from all areas of collection, existing as agglomerates (>500 nm) and nanoparticles (100-500 nm). Particle counts showed an increase in number concentration above background during a subset of the job tasks, but particle counts in the task areas were otherwise not significantly higher than background. Additional data is needed to

  15. A multilevel study on the association of observer-assessed working conditions with depressive symptoms among female eldercare workers from 56 work units in 10 care homes in Denmark

    DEFF Research Database (Denmark)

    Jakobsen, Louise M.; Jorgensen, Anette F. B.; Thomsen, Birthe L.;

    2015-01-01

    OBJECTIVES: Eldercare workers in Denmark have a higher prevalence of poor psychological health than other occupational groups. We examined the association between working conditions assessed by trained observers and depressive symptoms assessed by self-report in a study of female Danish eldercare...

  16. A multicenter study of biological effects assessment of pharmacy workers occupationally exposed to antineoplastic drugs in Pharmacy Intravenous Admixture Services.

    Science.gov (United States)

    Zhang, Jingjing; Bao, Jianan; Wang, Renying; Geng, Zhou; Chen, Yao; Liu, Xinchun; Xie, Yongzhong; Jiang, Ling; Deng, Yufei; Liu, Gaolin; Xu, Rong; Miao, Liyan

    2016-09-01

    This multi-centered study was designed to evaluate the biological effects of exposure to antineoplastic drugs (ADs) at PIVAS (Pharmacy Intravenous Admixture Service) across ten Chinese hospitals. 8-hydroxy-2-deoxyguanosine (8-OHdG) was used as a biomarker of DNA oxidative damage and lymphocyte apoptosis assays using peripheral lymphocyte cells were used to detect primary DNA damage. The mutagenicity activity was estimated with the Ames fluctuation test. 158 exposed and 143 unexposed workers participated in this study. The urinary 8-OHdG/Cr concentrations of the exposed group was 22.05±17.89ng/mg Cr, which was significantly higher than controls of 17.36±13.50ng/mg Cr (P<0.05). The rate of early lymphocyte apoptosis was slightly increased in exposed group than that of the control group (P=0.087). The mutagenic activity was significantly higher in the exposed group relative to the control group (P<0.05). Moreover, while no statistically significant difference was observed, higher concentrations of 8-OHdG/Cr in urine and an early lymphocyte apoptosis rate were found in exposed group II as compared to exposed group I. In addition, a significant correlation between early lymphocyte apoptosis and exposure time to ADs was also observed (P<0.05). In conclusion, our study identified elevated biomarkers in PIVAS workers exposed to ADs. However whether these findings could lead to increased incidence of genotoxic responses remains to be further investigated. PMID:27179702

  17. Some features of beryllium corrosion behavior in Be-liquid Li-V-4Ti-4Cr alloy system

    International Nuclear Information System (INIS)

    Recent experimental results on beryllium corrosion behavior in a V-4Ti-4Cr alloy, liquid lithium static system during testing for 200-500 h at temperatures from 600 to 800 deg. C are presented. The influence of test conditions (temperature, duration and lithium purity) and beryllium characteristics (microstructure, grain size and chemical composition) on weight loss of beryllium and penetration of lithium into beryllium are discussed. Results of compressive tests for beryllium specimens before and after corrosion testing are also introduced

  18. TEM study of impurity segregations in beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Klimenkov, M., E-mail: michael.klimenkov@kit.edu [Institute for Applied Materials – Applied Materials Physics, Karlsruhe Institute of Technology, Hermann-von-Helmholz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Chakin, V.; Moeslang, A. [Institute for Applied Materials – Applied Materials Physics, Karlsruhe Institute of Technology, Hermann-von-Helmholz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Rolli, R. [Institute for Applied Materials – Materials and Biomechanics, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany)

    2014-12-15

    Beryllium is planned to be used as a neutron multiplier in the Helium-cooled Pebble Bed European concept of a breeding blanket of demonstration power reactor DEMO. In order to evaluate the irradiation performance, individual pebbles and constrained pebble beds were neutron-irradiated at temperatures typical of fusion blankets. Beryllium pebbles 1 mm in diameter produced by the rotating electrode method were subjected to a TEM study before and after irradiation at High Flux Reactor, Petten, Netherlands at 861 K. The grain size varied in a wide range from sub-micron size up to several tens of micrometers, which indicated formation bimodal grain size distribution. Based on the application of combined electron energy loss spectroscopy and energy dispersive X-ray spectroscopy methods, we suggest that impurity precipitates play an important role in controlling the mechanical properties of beryllium. The impurity elements were present in beryllium at a sub-percent concentration form beryllide particles of a complex (Fe/Al/Mn/Cr)B composition. These particles are often ordered along dislocations lines, forming several micron-long chains. It can be suggested that fracture surfaces often extended along these chains in irradiated material.

  19. Beryllium Wipe Sampling (differing methods - differing exposure potentials)

    Energy Technology Data Exchange (ETDEWEB)

    Kerr, Kent

    2005-03-09

    This research compared three wipe sampling techniques currently used to test for beryllium contamination on room and equipment surfaces in Department of Energy facilities. Efficiencies of removal of beryllium contamination from typical painted surfaces were tested by wipe sampling without a wetting agent, with water-moistened wipe materials, and by methanol-moistened wipes. Analysis indicated that methanol-moistened wipe sampling removed about twice as much beryllium/oil-film surface contamination as water-moistened wipes, which removed about twice as much residue as dry wipes. Criteria at 10 CFR 850.30 and .31 were established on unspecified wipe sampling method(s). The results of this study reveal a need to identify criteria-setting method and equivalency factors. As facilities change wipe sampling methods among the three compared in this study, these results may be useful for approximate correlations. Accurate decontamination decision-making depends on the selection of appropriate wetting agents for the types of residues and surfaces. Evidence for beryllium sensitization via skin exposure argues in favor of wipe sampling with wetting agents that provide enhanced removal efficiency such as methanol when surface contamination includes oil mist residue.

  20. TEM study of impurity segregations in beryllium pebbles

    Science.gov (United States)

    Klimenkov, M.; Chakin, V.; Moeslang, A.; Rolli, R.

    2014-12-01

    Beryllium is planned to be used as a neutron multiplier in the Helium-cooled Pebble Bed European concept of a breeding blanket of demonstration power reactor DEMO. In order to evaluate the irradiation performance, individual pebbles and constrained pebble beds were neutron-irradiated at temperatures typical of fusion blankets. Beryllium pebbles 1 mm in diameter produced by the rotating electrode method were subjected to a TEM study before and after irradiation at High Flux Reactor, Petten, Netherlands at 861 K. The grain size varied in a wide range from sub-micron size up to several tens of micrometers, which indicated formation bimodal grain size distribution. Based on the application of combined electron energy loss spectroscopy and energy dispersive X-ray spectroscopy methods, we suggest that impurity precipitates play an important role in controlling the mechanical properties of beryllium. The impurity elements were present in beryllium at a sub-percent concentration form beryllide particles of a complex (Fe/Al/Mn/Cr)B composition. These particles are often ordered along dislocations lines, forming several micron-long chains. It can be suggested that fracture surfaces often extended along these chains in irradiated material.

  1. Codeposition of deuterium ions with beryllium oxide at elevated temperatures

    CERN Document Server

    Markin, A V; Gorodetsky, A E; Negodaev, M A; Rozhanskii, N V; Scaffidi-Argentina, F; Werle, H; Wu, C H; Zalavutdinov, R K; Zakharov, A P

    2000-01-01

    Deuterium-loaded BeO films were produced by sputtering the beryllium target with 10 keV Ne ions in D sub 2 gas at a pressure of approximately 1 Pa. The sputtered beryllium reacts - on the substrate surface - with the residual oxygen, thus forming a beryllium oxide layer. Biasing the substrate negatively with respect to the target provides the simultaneous bombardment of the growing film surface with D ions formed by Ne-D sub 2 collisions. Substrate potential governs the maximum energy of ions striking the growing film surface while its size governs the flux density. According to X-ray photoelectron spectroscopy (XPS), electron probe microanalysis (EPMA) and reflection high energy electron diffraction (RHEED) data, the beryllium is deposited in the form of polycrystalline hcp-BeO layers with negligible (about 1 at.%) carbon and neon retention. Thermal desorption spectroscopy (TDS) data shows a strong deuterium bonding, with a desorption peak at 950 K, in the films deposited at -50 and -400 V substrate potentia...

  2. Fluorometric determination of beryllium with 2-(o-hydroxylphenyl)benzoxazole

    Energy Technology Data Exchange (ETDEWEB)

    Gladilovich, D.B.; Stolyarov, K.P.

    1985-09-01

    According to the authors, of great interest for the fluorometric determination of small quantities of beryllium is 2-(o-hydroxyphenyl)benzthiazole (HPBT). In this work, 2-(o-hydroxyphenyl)benzoaxzole (HPBO), which is an analog of HPBT and differs from it in that the sulfur atom in the heterocyclic portion of the molecule is replaced by an oxygen atom, is proposed as a reagent for the fluorometric determination of beryllium. The fluorescent reaction of HPBO with beryllium is studied in this paper, in addition to the selection of the optimum conditions for the determination and the development of a procedure for the analysis of complex objects on this basis. The reaction proceeds in aqueous ethanol medium at pH 7.2-7.5. The limit of detection is 0.6 ng/ml. Methods have been developed for the determination of 10/sup -2/% beryllium in alloys based on copper and 10/sup -3/-10/sup -4/% in standard samples of silicate rocks.

  3. The uses and adverse effects of beryllium on health

    DEFF Research Database (Denmark)

    Cooper, Ross G.; Harrison, Adrian Paul

    2009-01-01

    in the current review for selecting articles were adopted from proposed criteria in The International Classification of Functioning, Disability, and Health. Articles were classified based on acute and chronic exposure and toxicity of beryllium. Results: The proportions of utilized and nonutilized articles were...

  4. The uses and adverse effects of beryllium on health

    Directory of Open Access Journals (Sweden)

    Cooper Ross

    2009-01-01

    Full Text Available Context: This review describes the health effects of beryllium exposure in the workplace and the environment. Aim: To collate information on the consequences of occupational and environmental exposure to beryllium on physiological function and well being. Materials and Methods: The criteria used in the current review for selecting articles were adopted from proposed criteria in The International Classification of Functioning, Disability, and Health. Articles were classified based on acute and chronic exposure and toxicity of beryllium. Results: The proportions of utilized and nonutilized articles were tabulated. Years 2001-10 gave the greatest match (45.9% for methodological parameters, followed by 27.71% for 1991-2000. Years 1971-80 and 1981-90 were not significantly different in the information published and available whereas years 1951-1960 showed a lack of suitable articles. Some articles were published in sources unobtainable through requests at the British Library, and some had no impact factor and were excluded. Conclusion: Beryllium has some useful but undoubtedly harmful effects on health and well-being. Measures need to be taken to prevent hazardous exposure to this element, making its biological monitoring in the workplace essential.

  5. Extraction of lead and beryllium from a firing site soil

    International Nuclear Information System (INIS)

    The Dual Axis Radiographic Hydrodynamic Test (DARHT) program is being implemented at LANL to conduct tests for evaluating the stability of the nation's aging nuclear stockpile. In order to reduce impact on the environment, containment of the non-fissile explosives tests is being phased in. The resulting shot debris can contain a mix of depleted uranium, lead, and beryllium. We are developing a treatment scheme to separate the radioactive and RCRA-hazardous components in order to recover the uranium, re-use some materials in future shots, and minimize waste for disposal. Our experience using a proprietary water soluble polymer to extract lead from contaminated soil to below TCLP levels has been extended to a surrogate soil from an open-air firing site that contains both lead and beryllium. Results for lead removal from this soil by dendrimers and molecular chelators will also be shown. Because of the potentially severe inhalation hazard associated with beryllium, the fate of this metal in our treatment scheme has been investigated, as well as extraction of beryllium using a variety of chemical agents

  6. Thermal cycling tests of actively cooled beryllium copper joints

    Energy Technology Data Exchange (ETDEWEB)

    Roedig, M.; Duwe, R.; Linke, J.; Schuster, A.; Wiechers, B. [Forschungszentrum Juelich GmbH (Germany)

    1998-01-01

    Screening tests (steady state heating) and thermal fatigue tests with several kinds of beryllium-copper joints have been performed in an electron beam facility. Joining techniques under investigation were brazing with silver containing and silver-free braze materials, hot isostatic pressing (HIP) and diffusion bonding (hot pressing). Best thermal fatigue performance was found for the brazed samples. (author)

  7. The use of the kurtosis metric in the evaluation of occupational hearing loss in workers in China: Implications for hearing risk assessment

    Directory of Open Access Journals (Sweden)

    Robert I Davis

    2012-01-01

    Full Text Available This study examined: (1 the value of using the statistical metric, kurtosis [β(t], along with an energy metric to determine the hazard to hearing from high level industrial noise environments, and (2 the accuracy of the International Standard Organization (ISO-1999:1990 model for median noise-induced permanent threshold shift (NIPTS estimates with actual recent epidemiological data obtained on 240 highly screened workers exposed to high-level industrial noise in China. A cross-sectional approach was used in this study. Shift-long temporal waveforms of the noise that workers were exposed to for evaluation of noise exposures and audiometric threshold measures were obtained on all selected subjects. The subjects were exposed to only one occupational noise exposure without the use of hearing protection devices. The results suggest that: (1 the kurtosis metric is an important variable in determining the hazards to hearing posed by a high-level industrial noise environment for hearing conservation purposes, i.e., the kurtosis differentiated between the hazardous effects produced by Gaussian and non-Gaussian noise environments, (2 the ISO-1999 predictive model does not accurately estimate the degree of median NIPTS incurred to high level kurtosis industrial noise, and (3 the inherent large variability in NIPTS among subjects emphasize the need to develop and analyze a larger database of workers with well-documented exposures to better understand the effect of kurtosis on NIPTS incurred from high level industrial noise exposures. A better understanding of the role of the kurtosis metric may lead to its incorporation into a new generation of more predictive hearing risk assessment for occupational noise exposure.

  8. Assessment of the occupational exposure of the workers involved in the 123I production at the IEN/CNEN-RJ

    International Nuclear Information System (INIS)

    123I is a gamma emitter used for diagnosis in Nuclear Medicine. Since 1998 it is produced in the Institute of Nuclear Energy (IEN) and supplied to the Clinics and Hospitals located in the city of Rio de Janeiro. The annual production is in the approximately of 0,74 TBq (20 Ci), which represents a risk of external and internal exposure to the workers involved in this activity. A survey of external doses in the period of 1994 to 2004 was carried out based on the individual registries available in the CONEXO Data Base operated by the Institute of Radiation Protection and Dosimetry (IRD). It was verified an increase of the external exposure associated to the production curve. However, the individual doses are all bellow the annual limits established by the regulatory board. On the other hand, the variation of doses among individuals involved in the same tasks suggests the possibility of optimization of procedures. Regarding internal exposure it was calculated a decision factor above 1mSv for the practice, which justifies the need for internal monitoring. An evaluation of the process based on the results of in vivo thyroid monitoring in the period of 2000 to 2004 was carried out to identify the steps which represent higher risk of internal exposure. The available data indicate that the laboratory of quality control is the critical step in terms of internal contamination. This conclusion can be justified by the high volatility of iodine which is manipulated in the form of a liquid open source during this step. With the aim of optimizing monitoring procedures for the control of occupationally exposed workers in the production of 123I, in vivo and in vitro bioassay methods were developed to identify and quantify internal contamination by such radionuclide, using the detection systems available at the Bioassay Laboratory and at the In Vivo Measurements Laboratory. The techniques developed present sensitivity compatible with the derived registry level associated to the

  9. Older workers

    NARCIS (Netherlands)

    Ybema,J.F.; Giesen, F.

    2014-01-01

    Due to an ageing population and global economic competition, there is a societal need for people to extend their working lives while maintaining high work productivity. This article presents an overview of the labour participation, job performance, and job characteristics of older workers in the Eur

  10. Field Note-Developing Suicide Risk Assessment Training for Hospital Social Workers: An Academic-Community Partnership

    Science.gov (United States)

    Wharff, Elizabeth A.; Ross, Abigail M.; Lambert, Susan

    2014-01-01

    This article describes 1 large urban pediatric hospital's partnership with a university to provide suicide assessment and management training within its social work department. Social work administrators conducted a department-wide needs assessment and implemented a 2-session suicide assessment training program and evaluation. Respondents…

  11. Assessment of the exposure of workers to the insecticide imidacloprid during application on various field crops by a hand-held power sprayer.

    Science.gov (United States)

    Choi, Hoon; Moon, Joon-Kwan; Kim, Jeong-Han

    2013-11-13

    Exposure assessment and risk assessment for imidacloprid were conducted for agricultural workers through mixing/loading and application with a power sprayer in four kinds of crop fields. The spray suspension was prepared with 10% wettable powder (250 g) for 5 min and applied on field crops for 1 h. A patch method and a personal air sampler with XAD-2 resin were used to monitor the dermal and inhalation exposure, respectively. In mixing/loading, the total dermal exposure on the whole body was 0.2 (cucumber) to 2.0 (apple) mg and the most exposed part of body was the hand (48-100% of total exposure). During the application of imidacloprid, whole dermal exposure was in the range of 2.9 (apple) to 9.5 (green pepper) mg. The primary sites exposed to pesticides were legs (51-79% of total exposure) in cucumber, green pepper, and paddy fields, whereas the primary sites were hands (35% of total exposure) in the apple field. The inhalation exposure was determined to be 0.2 (paddy) to 2.8 (cucumber) μg and 0.2 (paddy) to 3.0 (cucumber) μg during mixing/loading and application, respectively. The absorbable quantity of exposure and the margin of safety were determined for risk assessment. Workers were exposed through inhalation as 23-93 and 2-11% of the absorbable quantity of exposure during mixing and application, respectively. The margin of safety of all cases was much higher than 1, indicating the lowest possibility of risk. PMID:24111779

  12. Assessment of knowledge attitude and practice towards hepatitis B among health care workers in a tertiary care hospital

    Directory of Open Access Journals (Sweden)

    Farhana Siraj

    2016-01-01

    Results: This cross sectional prospective study was conducted in the Department of Obstetrics and Gynecology Govt. Medical College Srinagar from January to June 2015. 150 health care professionals were taken for the study. Knowledge regarding disease and transmission was fairly good. Regarding vaccination status 42.02% of medical and 29.60% of paramedical staff was fully vaccinated, the most common reason for non compliance being ignorance of importance of vaccination. Awareness of patients' vaccination status was also low. Conclusions: Due to low vaccine-compliance, Health care workers (HCW continue to be at the risk of occupational HBV infection. Regular Health education highlighting occupational risk of HBV, accessibility of vaccine, and mandatory vaccination of HCW is recommended to prevent Hepatitis B infection. [Int J Reprod Contracept Obstet Gynecol 2016; 5(1.000: 58-61

  13. Does a more refined assessment of exposure to bitumen fume and confounders alter risk estimates from a nested case-control study of lung cancer among European asphalt workers?

    DEFF Research Database (Denmark)

    Agostini, Michela; Ferro, Gilles; Burstyn, Igor;

    2013-01-01

    To investigate whether a refined assessment of exposure to bitumen fume among workers in the European asphalt industry within a nested case-control study resulted in a different interpretation pertaining to risk of lung cancer mortality compared with the cohort study.......To investigate whether a refined assessment of exposure to bitumen fume among workers in the European asphalt industry within a nested case-control study resulted in a different interpretation pertaining to risk of lung cancer mortality compared with the cohort study....

  14. Investigations of the ternary system beryllium-carbon-tungsten and analyses of beryllium on carbon surfaces; Untersuchung des ternaeren Systems Beryllium-Kohlenstoff-Wolfram und Betrachtungen von Beryllium auf Kohlenstoffoberflaechen

    Energy Technology Data Exchange (ETDEWEB)

    Kost, Florian

    2009-05-25

    Beryllium, carbon and tungsten are planned to be used as first wall materials in the future fusion reactor ITER. The aim of this work is a characterization of mixed material formation induced by thermal load. To this end, model systems (layers) were prepared and investigated, which give insight into the basic physical and chemical concepts. Before investigating ternary systems, the first step was to analyze the binary systems Be/C and Be/W (bottom-up approach), where the differences between the substrates PG (pyrolytic graphite) and HOPG (highly oriented pyrolytic graphite) were of special interest. Particularly X-ray photoelectron spectroscopy (XPS), low energy ion scattering (ISS) and Rutherford backscattering spectroscopy (RBS) were used as analysis methods. Beryllium evaporated on carbon shows an island growth mode, whereas a closed layer can be assumed for layer thicknesses above 0.7 nm. Annealing of the Be/C system induces Be{sub 2}C island formation for T{>=}770 K. At high temperatures (T{>=}1170 K), beryllium carbide dissociates, resulting in (metallic) beryllium desorption. For HOPG, carbide formation starts at higher temperatures compared to PG. Activation energies for the diffusion processes were determined by analyzing the decreasing beryllium amount versus annealing time. Surface morphologies were characterized using angle-resolved XPS (ARXPS) and atomic force microscopy (AFM). Experiments were performed to study processes in the Be/W system in the temperature range from 570 to 1270 K. Be{sub 2}W formation starts at 670 K, a complete loss of Be{sub 2}W is observed at 1170 K due to dissociation (and subsequent beryllium desorption). Regarding ternary systems, particularly Be/C/W and C/Be/W were investigated, attaching importance to layer thickness (reservoir) variations. At room temperature, Be{sub 2}C, W{sub 2}C, WC and Be{sub 2}W formation at the respective interfaces was observed. Further Be{sub 2}C is forming with increasing annealing temperatures

  15. Assessment of Extremely Low Frequency (ELF Electric and Magnetic Fields in Hamedan High Electrical Power Stations and their Effects on Workers

    Directory of Open Access Journals (Sweden)

    Farshid Ghorbani Shahna

    2011-09-01

    Full Text Available Introduction: Public and occupational exposure to extremely low frequency (ELF electric and magnetic fields induced by electrical equipment is a significant issue in the environment and at the workplace due to their potential health effects on public health. The purpose of this study was assessment of the electric and magnetic fields intensities and determination of mental and psychological effects of occupational exposure in the high voltage electric power stations in the city of Hamadan, Iran. Material and Methods: The intensities of the magnetic and electric fields were measured at eight high voltage electric power stations at three different intervals of sources using an HI-3604 instrument. A two-part questionnaire was used to assess mental and psychological effects of the exposure to these fields. Two groups of control and case workers including 30 samples were selected to determine the exposure effects. Results: The results of field measurements showed the highest average electric field intensity was related to the CVT unit with 3110 V/m at a 2 m distance from the source and the lowest average was related to the control room with 1.35 V/m next to the source. Also, the highest and lowest magnetic field intensities were close to the transformator 2 and the battery room (50.42 and 1.31 mG, respectively. Discussion and Conclusion: The intensities of electric and magnetic fields in the selected stations are lower than the ACGIH and ICNIRP standard levels for occupational exposures. The results obtained indicate that the distribution of these fields was nonlinear around the sources and the effects observed on exposed workers were non-thermal.

  16. Assessment of the quality of antenatal care services provided by health workers using a mobile phone decision support application in northern Nigeria: a pre/post-intervention study.

    Directory of Open Access Journals (Sweden)

    Marion McNabb

    Full Text Available Given the shortage of skilled healthcare providers in Nigeria, frontline community health extension workers (CHEWs are commonly tasked with providing maternal and child health services at primary health centers. In 2012, we introduced a mobile case management and decision support application in twenty primary health centers in northern Nigeria, and conducted a pre-test/post-test study to assess whether the introduction of the app had an effect on the quality of antenatal care services provided by this lower-level cadre.Using the CommCare mobile platform, the app dynamically guides CHEWs through antenatal care protocols and collects client data in real time. Thirteen health education audio clips are also embedded in the app for improving and standardizing client counseling. To detect changes in quality, we developed an evidence-based quality score consisting of 25 indicators, and conducted a total of 266 client exit interviews. We analyzed baseline and endline data to assess changes in the overall quality score as well as changes in the provision of key elements of antenatal care.Overall, the quality score increased from 13.3 at baseline to 17.2 at endline (p<0.0001, out of a total possible score of 25, with the most significant improvements related to health counseling, technical services provided, and quality of health education.These study results suggest that the introduction of a low-cost mobile case management and decision support application can spur behavior change and improve the quality of services provided by a lower level cadre of healthcare workers. Future research should employ a more rigorous experimental design to explore potential longer-term effects on client health outcomes.

  17. The PAediatric Risk Assessment (PARA) Mobile App to Reduce Postdischarge Child Mortality: Design, Usability, and Feasibility for Health Care Workers in Uganda

    Science.gov (United States)

    English, Lauren Lacey; Dunsmuir, Dustin; Kumbakumba, Elias; Ansermino, John Mark; Larson, Charles P; Lester, Richard; Barigye, Celestine; Ndamira, Andrew; Kabakyenga, Jerome

    2016-01-01

    Background Postdischarge death in children is increasingly being recognized as a major contributor to overall child mortality. The PAediatric Risk Assessment (PARA) app is an mHealth tool developed to aid health care workers in resource-limited settings such as Sub-Saharan Africa to identify pediatric patients at high risk of both in-hospital and postdischarge mortality. The intended users of the PARA app are health care workers (ie, nurses, doctors, and clinical officers) with varying levels of education and technological exposure, making testing of this clinical tool critical to successful implementation. Objective Our aim was to summarize the usability evaluation of the PARA app among target users, which consists of assessing the ease of use, functionality, and navigation of the interfaces and then iteratively improving the design of this clinical tool. Methods Health care workers (N=30) were recruited to participate at Mbarara Regional Referral Hospital and Holy Innocents Children’s Hospital in Mbarara, Southwestern Uganda. This usability study was conducted in two phases to allow for iterative improvement and testing of the interfaces. The PARA app was evaluated using quantitative and qualitative measures, which were compared between Phases 1 and 2 of the study. Participants were given two patient scenarios that listed hypothetical information (ie, demographic, social, and clinical data) to be entered into the app and to determine the patient’s risk of in-hospital and postdischarge mortality. Time-to-completion and user errors were recorded for each participant while using the app. A modified computer system usability questionnaire was utilized at the end of each session to elicit user satisfaction with the PARA app and obtain suggestions for future improvements. Results The average time to complete the PARA app decreased by 30% from Phase 1 to Phase 2, following user feedback and modifications. Participants spent the longest amount of time on the oxygen

  18. Selecting Young Workers: The Influence of Applicants' Education and Skills on Employability Assessments by Employers. Executive Summary.

    Science.gov (United States)

    Hollenbeck, Kevin; Smith, Bruce

    A study analyzed the explicit and implicit behavior of employers in their assessment of young job applicants for entry-level clerical, retail trade, and machine trade jobs. In order to determine the influence of applicants' education and skills on employability assessments made by employers, the researchers analyzed data from almost 600 mail…

  19. Older workers

    OpenAIRE

    Ybema, J.F.; Giesen, F.

    2014-01-01

    Due to an ageing population and global economic competition, there is a societal need for people to extend their working lives while maintaining high work productivity. This article presents an overview of the labour participation, job performance, and job characteristics of older workers in the European Union. The way in which several factors, including health, working conditions, skills and knowledge, and social and financial factors influence sustainable employability and the early retirem...

  20. Assessment of levels of occupational exposure to workers in radiofrequency fields of two television stations in Accra, Ghana.

    Science.gov (United States)

    Osei, S; Amoako, J K; Fletcher, J J

    2016-03-01

    A survey of the radiofrequency (RF) radiation was undertaken within the premises of two television (TV) stations, TVA and TVB, in Accra, Ghana. The primary objective of this study was to determine the level of RF exposure to workers in the TV stations. A spectrum analyser, a bi-conical antenna (30-300 MHz) and a log-periodic antenna (200 MHz-2.0 GHz) were used. Results obtained indicated that the wideband electric field strength levels recorded in this work vary between 0.006 and 58.5 V m(-1) at TVA and between 0.007 and 28.5 V m(-1) at TVB. Compared with the results from TVB, TVA recorded relatively higher values in the 30-400 MHz range, whereas TVB produced relatively higher values in the 400 MHz-1.7 GHz range. Generally, results obtained were found to be below the occupational reference levels of the International Commission on Non-Ionizing Radiation Protection, but at some locations, the field intensity was 4.3 times higher than the reference levels for the general public.

  1. Knowledge About the Waterpipe (Hookah), a Qualitative Assessment Among Community Workers in a Major Urban Center in Canada.

    Science.gov (United States)

    Hammal, Fadi; Wild, T Cameron; Finegan, Barry A

    2016-08-01

    Waterpipe (WP) use has surged in popularity since the introduction of flavoured shisha. It is now an increasingly popular form of smoking among youth in North America. Health professionals/educators knowledge about the WP may well be inadequate. This study, using qualitative methods, sought to explore the knowledge and attitude of leaders in the community toward the WP. Family physicians, pharmacists, tobacco counsellors, social workers and educators were invited to participate in a one-one interview using open-ended questions. A total of 27 interviews were conducted. Individuals from Eastern Mediterranean backgrounds raised doubt about the overemphasised cultural significance of the WP and perceived this as a marketing strategy by industry. Most felt that WP smokers believed the WP to be less harmful than cigarettes and that the use of flavoured tobacco was motivating people to smoke. Participants believed that education should be directed at the general public and healthcare professionals, suggesting school programs and the use of social media to inform young smokers. Most thought that the current practices regarding packaging and second hand smoke exposure are confusing. They identified the lack of knowledge, poor enforcement procedures, "so called cultural aspects" and the economic impact of banning the WP on small businesses as barriers to change. Despite the awareness of an increase in WP use, our participants recognized that little has been done to curb this problem. Our findings emphasize the need for further education and better legislation to regulate WP use and availability. PMID:26704909

  2. Assessment of levels of occupational exposure to workers in radiofrequency fields of two television stations in Accra, Ghana

    International Nuclear Information System (INIS)

    A survey of the radiofrequency (RF) radiation was undertaken within the premises of two television (TV) stations, TVA and TVB, in Accra, Ghana. The primary objective of this study was to determine the level of RF exposure to workers in the TV stations. A spectrum analyser, a bi-conical antenna (30-300 MHz) and a log-periodic antenna (200 MHz-2.0 GHz) were used. Results obtained indicated that the wideband electric field strength levels recorded in this work vary between 0.006 and 58.5 V m-1 at TVA and between 0.007 and 28.5 V m-1 at TVB. Compared with the results from TVB, TVA recorded relatively higher values in the 30-400 MHz range, whereas TVB produced relatively higher values in the 400 MHz-1.7 GHz range. Generally, results obtained were found to be below the occupational reference levels of the International Commission on Non-Ionizing Radiation Protection, but at some locations, the field intensity was 4.3 times higher than the reference levels for the general public. (authors)

  3. Prevalence of vibration-induced white finger and assessment of vibration exposure among travertine workers in Italy.

    Science.gov (United States)

    Bovenzi, M; Franzinelli, A; Strambi, F

    1988-01-01

    Among 76 stonedrillers and stonecutters/chippers working in the Rapolano travertine quarries (Tuscany, Italy), 27 subjects (35.5%) were affected with vibration-induced white finger (VWF). The median latent period for VWF was ten years (range 0.1-26 years). A VWF prevalence of 8% was found among 60 comparable controls (P less than 0.0001). Vibration measurements showed that the frequency-weighted accelerations for two rock-drills and two small chipping hammers ranged from 19.7 to 36.4 m/s2. Weighted accelerations between 2.4 and 4.1 m/s2 were measured on the handles of a vertical grinder and a hand cutter. Vibration data, daily exposure time and total duration of exposure period were used to calculate two indicators of vibration dose such as the four-hour, energy-equivalent, frequency-weighted acceleration (m/s2) and the vibration exposure level (dB). A significant association between the vibration exposure level and the severity of VWF stages was observed among the travertine operators. The dose-effect relationship proposed by ISO 5349 was not suitable for the data of the present study because it overestimates the risk due to hand-transmitted vibration in the travertine workers. Finally, the results of a cold test indicated that the rewarming time of fingertips to room temperature was more prolonged in the operators with VWF than in those without VWF and in the controls. PMID:3198281

  4. Beryllium coating produced by evaporation-condensation method and some their properties

    Energy Technology Data Exchange (ETDEWEB)

    Pepekin, G.I.; Anisimov, A.B.; Chernikov, A.S.; Mozherinn, S.I.; Pirogov, A.A. [SRI SIA Lutch., Podolsk (Russian Federation)

    1998-01-01

    The method of vacuum evaporation-condensation for deposition of beryllium coatings on metal substrates, considered in the paper, side by side with a plasma-spray method is attractive fon ITER application. In particular this technique may be useful for repair the surface of eroded tiles which is operated in a strong magnetic field. The possibility of deposition of beryllium coatings with the rate of layer growth 0.1-0.2 mm/h is shown. The compatibility of beryllium coating with copper or stainless steel substrate is provided due to intermediate barrier. The results of examination of microstructure, microhardness, porosity, thermal and physical properties and stability under thermal cycling of beryllium materials are presented. The value of thermal expansion coefficient and thermal conductivity of condensed beryllium are approximately the same as for industrial grade material produced by powder mettalurgy technique. However, the condensed beryllium has higher purity (up to 99.9-99.99 % wt.). (author)

  5. 5. IEA International workshop on beryllium technology for fusion. Book of abstracts

    International Nuclear Information System (INIS)

    The collection includes the abstracts of reports presented to the 5-th IEA international workshop on beryllium technology for fusion. The themes of reports are as follows: status of beryllium technology for fusion in Russia; manufacturing and testing of Be armoured first wall mock-up for ITER; development of the process of diffusion welding of metals stainless steel-copper-beryllium into a single composite; some features of beryllium-laser beam interaction; the effect of irradiation dose on tritium and helium release from neutron irradiated beryllium; thermal properties of neutron irradiated Be12Ti. The results of investigating the mechanical properties variation and swelling of beryllium under high temperature neutron irradiation are presented

  6. JET-ISX-B beryllium limiter experiment safety analysis report and operational safety requirements

    International Nuclear Information System (INIS)

    An experiment to evaluate the suitability of beryllium as a limiter material has been completed on the ISX-B tokamak. The experiment consisted of two phases: (1) the initial operation and characterization in the ISX experiment, and a period of continued operation to the specified surface fluence (1022 atoms/cm2) of hydrogen ions; and (2) the disassembly, decontamination, or disposal of the ISX facility. During these two phases of the project, the possibility existed for beryllium and/or beryllium oxide powder to be produced inside the vacuum vessel. Beryllium dust is a highly toxic material, and extensive precautions are required to prevent the release of the beryllium into the experimental work area and to prevent the contamination of personnel working on the device. Details of the health hazards associated with beryllium and the appropriate precautions are presented. Also described in appendixes to this report are the various operational safety requirements for the project

  7. Proceedings of the 8th specialist meeting on recycling of irradiated Beryllium

    International Nuclear Information System (INIS)

    This report summarizes the documents presented in the 8th Specialist Meeting on Recycling of Irradiated Beryllium, which was held on October 28, 2013, in Bariloche, Río Negro, Argentina, hosted by INVAP and CNEA (Comision Nacional de Energia Atomica). The objective of the meeting is to exchange the information of current status and future plan for beryllium study in the Research/Testing reactors, and to make a discussion of “How to cooperate”. There were 20 participants from USA, Japan, Korea, Austria and Argentina. In this meeting, information exchange of current status and future plan for beryllium study was carried out for the Research/Testing reactor fields, and evaluation results of beryllium materials were discussed based on new irradiated beryllium data such as swelling, deformation, gas release and so on. The subject of the used beryllium recycling was also discussed for the enforcement of demonstration recycling tests. (author)

  8. Effects of beryllium-compounds on the hen. 2. Comm

    International Nuclear Information System (INIS)

    After oral application of 7Be2+ this cation is relative slowly absorbed from the intestine. The highest proportion of 7Be appeared in the feces. The absorbed 7Be has been found in the feathers, the bones and in the muscles as well as in the mucosa of the stomach and the intestine. Relative low is the accumulation in the liver and the kidneys as well as in the brain and the spinal cord. After i.v. application a high proportion of 7Be has been observed in the eggs. The rest of the applied radio-beryllium has been accumulated 7Be in the metabolically active tissues is removed very slowly. In contrast to this observation radio-beryllium disappeared relatively rapidly from the blood. (orig.)

  9. Quantum-chemical approach to cohesive properties of metallic beryllium

    International Nuclear Information System (INIS)

    Calculations based upon the incremental approach, i.e. an expansion of the correlation energy in terms of one-body, two-body, and higher-order contributions from localized orbital groups, have been performed for metallic beryllium. We apply an embedding scheme which has been successfully applied recently to ground-state properties of magnesium and group 12 elements. This scheme forces localization in metallic-like model systems and allows for a gradual delocalization within the incremental approach. Quantum-chemical methods of the coupled-cluster and multi-reference configuration interaction type are used for evaluating individual increments. Results are given for the cohesive energy and lattice constants of beryllium, and it is shown that further development of the approach is needed for this difficult case

  10. Neopterin: A candidate biomarker for the early assessment of toxicity of aluminum among bauxite dust exposed mine workers

    Directory of Open Access Journals (Sweden)

    Shubhangi K Pingle

    2015-01-01

    Full Text Available Introduction: Bauxite ore is a major source of aluminum (Al which contains approximately 35–60% Al by weight. Occupational and environmental bauxite dust exposure may cause toxicity by interaction with human biological systems resulting in oxidative stress (OS and cell death. A neopterin derivative as an antioxidant is able to modulate cytotoxicity by the induction of OS. Materials and Methods: A total of 273 subjects were selected for blood collection from three different major Al producing bauxite mines and were categorized into three groups as experimental (Exp (n = 150, experimental controls (ExC (n = 73 and control (Con (n = 50. Whole blood and serum samples were used for measurement of Al, neopterin, urea and creatinine values. Statistical analysis was performed using R-2.15.1 programming language. Results and Discussion: The result showed that age, body mass index and the behavioral habits, that is, smoking, tobacco and alcohol consumption have possible effects on neopterin level. Serum neopterin levels were found to be significantly higher (P <0.0001 in the experimental group as compared to other groups. Significantly positive correlation (P < 0.0001 was observed between neopterin and creatinine. It was also observed that neopterin level increases as the duration of exposure increases. Conclusion: On the basis of findings it was concluded that exposure to bauxite dust (even at low levels of Al changes biochemical profile leading to high levels of serum neopterin. Levels of serum neopterin in workers exposed to bauxite dust were probably examined for the 1st time in India. The outcome of this study suggested that serum neopterin may be used as potential biomarker for early detection of health risks associated with bauxite dust exposed population.

  11. Assessing the quality of service of village malaria workers to strengthen community-based malaria control in Cambodia

    Directory of Open Access Journals (Sweden)

    Ly Po

    2010-04-01

    Full Text Available Abstract Background Malaria continues to be a major public health problem in remote forested areas in Cambodia. As a national strategy to strengthen community-based malaria control, the Cambodian government has been running the Village Malaria Worker (VMW project since 2001. This study sought to examine the nature and quality of the VMWs' services. Methods Data collection was carried out in February and March 2008 through interviews with one of the two VMWs who takes the lead in malaria control activities in each of the 315 VMW villages (n = 251. The questionnaire addressed 1 the sociodemographic characteristics of VMWs, 2 service quality, 3 actions for malaria prevention and vector control, and 4 knowledge of malaria epidemiology and vector ecology. Results VMWs were effective in conducting diagnosis with Rapid Diagnostic Tests (RDTs and prescribing anti-malarials to those who had positive RDT results, skills that they had acquired through their training programmes. However, most other services, such as active detection, explanations about compliance, and follow-up of patients, were carried out by only a small proportion of VMWs. The variety of actions that VMWs took for malaria prevention and vector control was small (average action index score 12.8/23, and their knowledge was very limited with less than 20% of the VMWs giving correct answers to six out of seven questions on malaria epidemiology and vector ecology. Knowledge of vector breeding places and malaria transmission were significant determinants of both the quality of VMWs' services and the variety of their actions for malaria prevention and vector control. Conclusions VMWs' services focused primarily on diagnosis and treatment. Their focus needs to be broadened to cover other aspects of malaria control in order to further strengthen community-based malaria control. VMWs' actions and knowledge also need substantial improvement. Strengthening training programmes can help achieve better

  12. Clandestine migrant workers in Japan.

    Science.gov (United States)

    Nagayama, T

    1992-01-01

    The author assesses the problem of illegal labor migration to Japan. "Labor policies, regulations, types of immigration violations, and the role of the recruitment industry are described. Most of the estimated 200,000 illegal workers are employed in small and medium sized enterprises, especially construction and manufacturing, which pay them wages well below the normal rate. A key issue is the infringement of human rights of these illegal workers, who lack the protection of labor laws and the social security system."

  13. Studies on extraction of beryllium from thiocyanate solutions by quaternary ammonium halides.

    Science.gov (United States)

    El-Yamani, I S; El-Messieh, E N

    A 0.4M tricaprylmethylammonium chloride solution in n-hexane was used for the quantitative extraction of beryllium from hydrochloric acid (pH 3) and 5M potassium thiocyanate. Beryllium was stripped from the organic phase with 1M sodium hydroxide, then determined volumetrically with bismuthyl perchlorate and bromocresol green indicator. Beryllium was extracted in presence of a large number of elements which are usually associated with it in beryl and in fission products of nuclear fuel.

  14. Dose Rates from Plutonium Metal and Beryllium Metal in a 9975 Shipping Container

    International Nuclear Information System (INIS)

    A parametric study was performed of the radiation dose rates that might be produced if plutonium metal and beryllium metal were shipped in the 9975 shipping package. These materials consist of heterogeneous combinations plutonium metal and beryllium. The plutonium metal content varies up to 4.4 kilograms while the beryllium metal varies up to 4 kilograms. This paper presents the results of that study

  15. Low-energy electronic stopping for boron in beryllium

    International Nuclear Information System (INIS)

    The range distribution for 50-keV boron bombarding beryllium was measured by an energetic ion-beam backscattering technique using helium ions. This distribution was compared with the range calculated with computer code EDEP1, with the result k 0.101 ± 0.013 for the electronic-stopping k-value. This value is compared with the results of recent interpolations from measurements of other elements. (author)

  16. Presence of Beryllium (Be) in urban soils: human health risk

    Energy Technology Data Exchange (ETDEWEB)

    Pena, A.; Gonzalez, M. J.; Lobo, M. C.

    2009-07-01

    Berylium (Be) is, together with As, Cd, Hg, Pb and Ti, one of the trace elements more toxic for human being (Vaessen) and Szteke, 2000; Yaman and Avci, 2006), but in spite of the exponential increment of its applications during the last decades, surprisingly there isn't hardly information about its presence and environmental distribution. The aim of this work is to evaluate the presence of Beryllium in urban soils in Alcala de Henares, (Madrid Spain).

  17. Analysis of features of the deformation of auxetic beryllium

    OpenAIRE

    Гунько, Михаил Николаевич; Олейнич-Лысюк, Алла Васильевна; Раранский, Николай Дмитриевич; Тащук, Александр Юрьевич

    2015-01-01

    In the framework of the linear elasticity theory using the experimentally obtained elastic stiffness modules, temperature dependences of the elastic compliance modules and tensor components of Poisson's ratios    of beryllium in a wide range of temperatures and directions in the crystal lattice were calculated, and it was shown that with increasing temperature, the value and signs of Poisson's ratios  change differently in various temperature intervals. In the interval 0-300K,  become negativ...

  18. Beryllium, Lithium and Oxygen Abundances in F-type Stars

    CERN Document Server

    García-López, R J; Pérez de Taoro, M R; Casares, C; Rasilla, J L; Rebolo, R; Allende-Prieto, C

    1997-01-01

    Beryllium and oxygen abundances have been derived in a sample of F-type field stars for which lithium abundances had been measured previously, with the aim of obtaining observational constraints to discriminate between the different mixing mechanisms proposed. Mixing associated with the transport of angular momentum in the stellar interior and internal gravity waves within the framework of rotating evolutionary models, appear to be promising ways to explain the observations.

  19. Health in relation to occupational exposure to pesticides in the Dutch flower bulb culture : Part 3A : neurobehavioral assessment of workers occupationally exposed to pesticides in the bulb growing industry

    NARCIS (Netherlands)

    Emmen, H.H.; Hooisma, J.; Kullig, B.M.; Brouwer, E.J.

    1992-01-01

    The purpose of the present study was to evaluate the possible effects of occupational exposure to pesticides on central nervous system (CNS) function. A variety of neurobehavioral functions were assessed in a group of 129 workers in the bulb growing industry with at least ten years occupational expo

  20. Hospital-based cluster randomised controlled trial to assess effects of a multi-faceted programme on influenza vaccine coverage among hospital healthcare workers and nosocomial influenza in the Netherlands, 2009 to 2011

    NARCIS (Netherlands)

    Riphagen-Dalhuisen, J.; Burgerhof, J.G.; Frijstein, G.; van der Geest-Blankert, AD; Danhof-Pont, M.B.; de Jager, H.J.; Bos, A.A.; Smeets, E.E.; de Vries, M.J.; Gallee, P.M.; Hak, E.

    2013-01-01

    Nosocomial influenza is a large burden in hospitals. Despite recommendations from the World Health Organization to vaccinate healthcare workers against influenza, vaccine uptake remains low in most European countries. We performed a pragmatic cluster randomised controlled trial in order to assess th

  1. Detail analysis of fusion neutronics benchmark experiment on beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Konno, Chikara, E-mail: konno.chikara@jaea.go.j [Fusion Research and Development Directorate, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki-ken 319-1195 (Japan); Ochiai, Kentaro; Takakura, Kosuke; Ohnishi, Seiki; Kondo, Keitaro [Fusion Research and Development Directorate, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki-ken 319-1195 (Japan); Wada, Masayuki [Japan Computer System, Mito-shi, Ibaraki-ken 310-0805 (Japan); Sato, Satoshi [Fusion Research and Development Directorate, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki-ken 319-1195 (Japan)

    2010-12-15

    Our previous analysis of the integral experiments (in situ and TOF experiments) on beryllium with DT neutrons at JAEA/FNS pointed out two problems by using MCNP4C and the latest nuclear data libraries; one was a strange larger neutron peak around 12 MeV appearing in the TOF experiment analysis with JEFF-3.1 and the other was an overestimation on law energy neutrons in the in situ experiment analyses with all the nuclear data libraries. We investigated reasons for these problems in detail. It was found out that the official ACE file MCJEFF3.1 of JEFF-3.1 had an inconsistency with the original JEFF-3.1, which caused the strange larger neutron peak around 12 MeV in the TOF experiment analysis. We also found out that the calculated thermal neutron peak was probably too large in the in situ experiment. On trial we examined influence of the thermal neutron scattering law data of beryllium metal in ENDF/B-VI. The result pointed out that the coherent elastic scattering cross-section data in the thermal neutron scattering law data of beryllium metal were probably too large.

  2. Electron microscope study of thin beryllium lamellae (1963)

    International Nuclear Information System (INIS)

    Thin SR beryllium lamellae are examined by electron microscopy after various treatments, together with other samples made up of Be - Fe at 1 per cent and 0.2 per cent iron. The SR beryllium is examined after annealing at 750 deg C and 900 deg C, strongly cold-worked and quenched at 900 deg C. At 950 deg C the metal is perfectly annealed; at 750 deg C the polygonisation is almost complete, the dislocations are arranged either is dislocation walls in the prismatic planes, or in hexagonal lattices with non-dissociated nodes suggesting a high stacking defect energy. The cold-worked structure has a high dislocation density and already existing crystal walls. In the quenched state, the few dislocations are very straight and are aligned in the crystallographic directions. Iron-precipitation is studied in two alloys during tempering at 660 deg after quenching in salt water. The precipitate appears at the grain boundaries and then spreads through the matrix leaving a depleted zone in the neighbourhood of the joints. These precipitates, in the form of platelets parallel to the base planes of the beryllium lattice have been identified as the inter metallic phase Be11 Fe oriented in relation to the matrix (0 0 0 1)//(0 0 0 1) (1 0 1-bar 0)//(1 1 2-bar 0). (authors)

  3. Elastic, micro- and macroplastic properties of polycrystalline beryllium

    Science.gov (United States)

    Kardashev, B. K.; Kupriyanov, I. B.

    2011-12-01

    The Young's modulus and the internal friction of beryllium polycrystals (size grain from 6 to 60 μm) prepared by the powder metallurgy method have been studied as functions of the amplitude and temperature in the range from 100 to 873 K. The measurements have been performed using the composite piezoelectric vibrator method for longitudinal vibrations at frequencies about 100 kHz. Based on the acoustic measurements, the data have been obtained on the elastic and inelastic (microplastic) properties as functions of vibration stress amplitudes within the limits from 0.2 to 30-60 MPa. The microplastic deformation diagram is shown to become nonlinear at the amplitudes higher than 5 MPa. The beryllium mechanical characteristics (the yield strength σ 0.2, the ultimate strength σ u , and the conventional microscopic yield strength σ y ) obtained with various grain sizes are compared. At room temperature, all the parameters satisfactorily obey the Hall-Petch relationship, although there is no complete similarity. The temperature dependences are quite different, namely: σ 0.2( T) and σ u ( T) decrease monotonically during heating from room temperature to higher temperatures; however, σ y ( T) behaves unusually, and it has a minimum near 400 K. The different levels of stresses and the absence of similarity indicate that the scattering of the ultrasound energy and the formation of a level of the macroscopic flow stresses in beryllium occur on dislocation motion obstacles of different origins.

  4. A diethylhydroxylaminate based mixed lithium/beryllium aggregate

    Energy Technology Data Exchange (ETDEWEB)

    Berger, Raphael J.F. [Paris-Lodron Universitaet Salzburg (Austria). Fachbereich fuer Materialwissenschaften und Physik; Jana, Surajit [Asansol Girls College, West-Bengal (India). Dept. of Chemistry; Froehlich, Roland [Muenster Univ. (Germany). Organisch-Chemisches Inst.; Mitzel, Norbert W. [Bielefeld Univ. (Germany). Anorganische Chemie und Strukturchemie

    2015-07-01

    A mixed lithium/beryllium diethylhydroxylaminate compound containing {sup n}butyl beryllium units of total molecular composition {sup n}Be(ONEt{sub 2}){sub 2} [(LiONEt{sub 2}){sup 2} {sup n}BuBeONEt{sub 2}]{sub 2} (1) was isolated from a reaction mixture of {sup n}butyl lithium, N,N-diethylhydroxylamine and BeCl{sub 2} in diethylether/thf. The crystal structure of 1 has been determined by X-ray diffraction. The aggregate is composed of two ladder-type subunits connected in a beryllium-centered distorted tetrahedron of four oxygen atoms. Only the lithium atoms are engaged in coordination with the nitrogen donor atoms. The DFT calculations support the positional occupation determined for Li and Be in the crystal structure. The DFT and the solid-state structure are in excellent agreement, indicating only weak intermolecular interactions in the solid state. Structural details of metal atom coordination are discussed.

  5. Beryllium Science: US-UK agreement on the use of Atomic Energy for mutual defense

    Energy Technology Data Exchange (ETDEWEB)

    Hanafee, J.E. (ed.)

    1988-02-19

    Twenty-seven papers are presented on beryllium supply, production, fabrication, safe handling, analysis, powder technology, and coatings. Separate abstracts have been prepared for the individual papers. (DLC)

  6. Problems and future plan on material development of beryllium in materials testing reactors

    International Nuclear Information System (INIS)

    Beryllium has been utilized as a moderator and/or reflector in a number of material testing reactors. The attractive nuclear properties of beryllium are its low atomic number, low atomic weight, low parasitic capture cross section for thermal neutrons, readiness to part with one of its own neutrons, and good neutron elastic scattering characteristics. However, it is difficult to reprocess irradiated beryllium because of high induced radioactivity. Disposal has also been difficult because of toxicity issues and special nuclear material controls. In this paper, problems and future plans of beryllium technology are introduced for nuclear reactors. (author)

  7. The impact of beryllium chloride and oxide on sexual function and offspring development in female rats

    International Nuclear Information System (INIS)

    The comparative study of the action of soluble chloride and difficultly soluble beryllium oxide on sexual cycle in female rats and their conception capability, revealing of embryotoxic and teratogenic effect of these compounds and determination of significance of terms of their impact on pregnant female as well as beryllium capability to penetrate through the placenta and accumulate in the offspring organism have been performed. A great potential danger of impact on animal reproductive function of soluble (chloride) beryllium compounds as compared with low soluble ones (oxide). In the genesis of embryotoxic teratonic effect probably along with beryllium impact on progeny through the maternal organism there occurs its direct impact on the offspring

  8. Vacuum Brazing of Beryllium Copper Components for the National Ignition Facility

    Energy Technology Data Exchange (ETDEWEB)

    Tyhurst, C.C.; Cunningham, M.A.

    2002-06-04

    A process for vacuum brazing beryllium copper anode assemblies was required for the Plasma Electrode Pockels Cell System, or PEPC, a component for the National Ignition Facility (NIF). Initial problems with the joint design and wettability of the beryllium copper drove some minor design changes. Brazing was facilitated by plating the joint surface of the beryllium copper rod with silver 0.0006 inch thick. Individual air sampling during processing and swipe tests of the furnace interior after brazing revealed no traceable levels of beryllium.

  9. Beryllium Science: US-UK agreement on the use of Atomic Energy for mutual defense

    International Nuclear Information System (INIS)

    Twenty-seven papers are presented on beryllium supply, production, fabrication, safe handling, analysis, powder technology, and coatings. Separate abstracts have been prepared for the individual papers

  10. How vulnerable are automobile repair workers to HIV/AIDS? A quantitative and qualitative assessment in a slum of Kolkata,India

    Directory of Open Access Journals (Sweden)

    Mukherjee Shuvankar

    2012-11-01

    Full Text Available Background: Automobile repair workers may run high risk of acquiring HIV/AIDS infection owing to their socio cultural background. A cross- sectional study was conducted among them in Chetla, Kolkata to assess knowledge, attitude and practices related to HIV/AIDS and to find out difference in knowledge status based on different socio-demographic variables. Materials and Methods: Both qualitative and quantitative methods were adopted. A total of 114 male workers were interviewed from randomly selected 12 automobile garages using pre-designed, pre-tested schedule. A uniform scoring system for knowledge was adopted. Chi-square test was applied to find out difference in knowledge score based on different socio-demographic variables. Qualitative analysis was performed after conducting in-depth interview with 24 participants. Results: About 84% belonged to 15-35 years age group with mean age 26.3(+ 2.7 years. Overall, 63.2% had poor knowledge score. Higher difference in knowledge score was obtained with higher literacy status and age (p<0.05. About 29 % of the respondents opined that People Living with HIV/AIDS (PLHAs should not continue their work and 47.4% commented that PLHAs should not reveal their HIV status. One of the three participants who had commercial sex in last 12 months did not use condom. Two participants complained about symptom of genital discharge in last 12 months and none underwent any treatment. Qualitative analysis revealed low awareness level and discriminatory attitude towards PLHAs.Conclusions: Poor level of knowledge and unfavourable attitude of the participants were observed from both quantitative and qualitative analyses though they could not be considered high risk group. Appropriate communication for behavioural change both by group approach and by interpersonal communication was required.

  11. Valoración de la aptitud laboral en trabajadoras sanitarias con cáncer de mama Labor capability assessment for health workers with breast cancer

    Directory of Open Access Journals (Sweden)

    Consuelo Rodrigo García-Pando

    2011-09-01

    Full Text Available El cáncer de mama es el tumor más frecuente en las mujeres occidentales y afectará a una de cada ocho mujeres a lo largo de su vida. Su incidencia se ha incrementado pero la tasa de mortalidad ha descendido. El médico del trabajo debe valorar y adoptar las medidas de prevención adecuadas para atenuar los riesgos a los que puedan estar expuestos los trabajadores especialmente sensibles en el ámbito sanitario. Nuestro objetivo es proponer un método para esta valoración así como las adaptaciones necesarias para el desempeño de su tarea. Partimos de una revisión bibliográfica del cáncer de mama y se analizan los riesgos laborales del ámbito sanitario que pudieran suponer un agravamiento de las condiciones de salud de la trabajadora afectada. Exponemos un modelo de reconocimiento médico y valoración de la capacidad funcional adaptado a las secuelas más probables presentadas por las mujeres que han sido diagnosticadas de cáncer de mama, para proponer unos criterios de aptitud y recomendaciones de adecuación del puesto de trabajo.Breast cancer is the most frequent tumour in occidental women and it will affect one in eight women throughout their lives. Over the years, incidence rate has increased, whereas, mortality rate has decreased. The labour physician has to assess and decide on the suitable prevention measures to reduce those labour risks to which especially sensitive health workers may be exposed in their labour environment. Our objective is to propose a method for carrying out the assessment and the necessary adjustments for them to do their job. We begin with a bibliographic review about breast cancer to analyze the risks found in the health work environment that could worsen health conditions of the affected worker. We expose a model of medical examinations and assessment of the functional capacity, adapted to the most usual sequels shown up in women that have been diagnosed with breast cancer. We can then propose some

  12. Beryllium Concentrations at European Workplaces: Comparison of 'Total' and Inhalable Particulate Measurements.

    Science.gov (United States)

    Kock, Heiko; Civic, Terence; Koch, Wolfgang

    2015-07-01

    A field study was carried out in order to derive a factor for the conversion of historic worker exposure data on airborne beryllium (Be) obtained by sampling according to the 37-mm closed faced filter cassette (CFC) 'total' particulate method into exposure concentration values to be expected when sampling using the 'Gesamtstaubprobenahmesystem' (GSP) inhalable sampling convention. Workplaces selected to represent the different copper Be work processing operations that typically occur in Germany and the EU were monitored revealing a broad spectrum of prevailing Be size distributions. In total, 39 personal samples were taken using a 37-mm CFC and a GSP worn side by side for simultaneous collection of the 'total' dust and the inhalable particulates, respectively. In addition, 20 static general area measurements were carried out using GSP, CFC, and Respicon samplers in parallel, the latter one providing information on the extra-thoracic fraction of the workplace aerosol. The study showed that there is a linear relationship between the concentrations measured with the CFC and those measured with the GSP sampler. The geometric mean value of the ratios of time-weighted average concentrations determined from GSP and CFC samples of all personal samples was 2.88. The individual values covered a range between 1 and 17 related to differences in size distributions of the Be-containing particulates. This was supported by the area measurements showing that the conversion factor increases with increasing values of the extra-thoracic fraction covering a range between 0 and 79%. PMID:25808693

  13. Beryllium metal I. experimental results on acute oral toxicity, local skin and eye effects, and genotoxicity.

    Science.gov (United States)

    Strupp, Christian

    2011-01-01

    The toxicity of soluble metal compounds is often different from that of the parent metal. Since no reliable data on acute toxicity, local effects, and mutagenicity of beryllium metal have ever been generated, beryllium metal powder was tested according to the respective Organisation for Economical Co-Operation and Development (OECD) guidelines. Acute oral toxicity of beryllium metal was investigated in rats and local effects on skin and eye in rabbits. Skin-sensitizing properties were investigated in guinea pigs (maximization method). Basic knowledge about systemic bioavailability is important for the design of genotoxicity tests on poorly soluble substances. Therefore, it was necessary to experimentally compare the capacities of beryllium chloride and beryllium metal to form ions under simulated human lung conditions. Solubility of beryllium metal in artificial lung fluid was low, while solubility in artificial lysosomal fluid was moderate. Beryllium chloride dissolution kinetics were largely different, and thus, metal extracts were used in the in vitro genotoxicity tests. Genotoxicity was investigated in vitro in a bacterial reverse mutagenicity assay, a mammalian cell gene mutation assay, a mammalian cell chromosome aberration assay, and an unscheduled DNA synthesis (UDS) assay. In addition, cell transformation was tested in a Syrian hamster embryo cell assay, and potential inhibition of DNA repair was tested by modification of the UDS assay. Beryllium metal was found not to be mutagenic or clastogenic based on the experimental in vitro results. Furthermore, treatment with beryllium metal extracts did not induce DNA repair synthesis, indicative of no DNA-damaging potential of beryllium metal. A cell-transforming potential and a tendency to inhibit DNA repair when the cell is severely damaged by an external stimulus were observed. Beryllium metal was also found not to be a skin or eye irritant, not to be a skin sensitizer, and not to have relevant acute oral

  14. Reducing workers' compensation costs.

    Science.gov (United States)

    Killian, M J

    1994-01-01

    Employers can reduce their workers' compensation costs by encouraging internal communication and education before and after injuries occur. Comprehensive workers' compensation programs can be developed by integrating the management of employee benefits and workers' compensation claims. PMID:10133659

  15. Assessment of exposure of workers to ionizing radiation from radioiodine and technetium in nuclear medicine departmental facilities

    Directory of Open Access Journals (Sweden)

    Grażyna Krajewska

    2013-10-01

    Full Text Available Background: Due to its use of ionising radiation, the field of nuclear medicine is a unique and significant part of medical diagnostics and patient treatment. The aim of this study was to assess the internal exposure of nuclear medicine employees to radioiodine 131I and technetium 99mTc as well as to assess the external exposure doses. Material and Methods: The radioiodine 131I and technetium 99mTc contents in the thyroid of staff members (about 100 persons dealing with these radionuclides have been measured in four departments of nuclear medicine. The measurements were conducted with a portable detection unit for in situ measurements of radioiodine and technetium. High sensitivity environmental thermoluminescent dosimeters (TLD were used to measure the external exposure dose. Results: The average values and ranges of radioiodine 131I activity measured in the thyroids of all of the medical units' employees were: 83 Bq (range: 70-250 Bq, 280 Bq (range: 70-4000 Bq, 275 Bq (range: 70-1000 Bq for technical staff, nuclear medicine staff and hospital services staff, respectively. The mean value of technetium 99mTc content in the thyroids of nuclear medicine staff was approximately 1500 Bq (range: 50- -1800 Bq. External exposure dose rates were in the range of 0.5-10 μGy/h. Conclusions: The calculated average effective dose for particular person caused by the inhalation of radioiodine 131I is below 5% of 20 mSv/year (occupational exposure limit. Med Pr 2013;64(5:625–630

  16. Analysis of the KANT experiment on beryllium using TRIPOLI-4 Monte Carlo code

    International Nuclear Information System (INIS)

    Beryllium is an important material in fusion technology for multiplying neutrons in blankets. However, beryllium nuclear data are differently presented in modern nuclear data evaluations. Recent investigations with the TRIPOLI-4 Monte Carlo simulation of the tritium breeding ratio (TBR) demonstrated that beryllium reaction data are the main source of the calculation uncertainties between ENDF/B-VII.0 and JEFF-3.1. To clarify the calculation uncertainties from data libraries on beryllium, in this study TRIPOLI-4 calculations of the Karlsruhe Neutron Transmission (KANT) experiment have been performed by using ENDF/B-VII.0 and new JEFF-3.1.1 data libraries. The KANT Experiment on beryllium has been used to validate neutron transport codes and nuclear data libraries. An elaborated KANT experiment benchmark has been compiled and published in the NEA/SINBAD database and it has been used as reference in the present work. The neutron multiplication in bulk beryllium assemblies was considered with a central D-T neutron source. Neutron leakage spectra through the 5, 10, and 17 cm thick spherical beryllium shells were calculated and five-group partial leakage multiplications were reported and discussed. In general, improved C/E ratios on neutron leakage multiplications have been obtained. Both ENDF/B-VII.0 and JEFF-3.1.1 beryllium data libraries of TRIPOLI-4 are acceptable now for fusion neutronics calculations.

  17. Proceedings of the third IEA international workshop on beryllium technology for fusion

    International Nuclear Information System (INIS)

    This report is the Proceedings of the Third International Energy Agency International Workshop on Beryllium Technology for Fusion. The workshop was held on October 22-24, 1997, at the Sangyou Kaikan in Mito City with 68 participants who attended from the Europe, the Russian Federation, the Kazakstan, the United States and Japan. The topics for papers were arranged into 9 sessions; beryllium applications for ITER, production and characterization, chemical compatibility and corrosion, forming and joining, plasma/tritium interactions, beryllium coating, first wall applications, neutron irradiation effects, health and safety. To utilize beryllium in the pebble type blanket, a series of discussions were intensified in multiple view points such as the swelling, He/T release from beryllium pebble irradiated up to high He content, effective thermal conductivity, tritium permeation and coating, and fabrication cost, and so on. As the plasma facing material, life time of beryllium and coated beryllium, dust and particle production, joining, waste treatment, mechanical properties and deformation by swelling were discussed as important issues. Especially, it was recognized throughout the discussions that the comparative study by the different researchers should be carried out to establish the reliability of the data reported in the workshop and in others. To enhance the comparative study, the world wide collaboration for the relative evaluation of the beryllium was proposed by the International Organization Committee and the proposal was approved by all of the participants. The 45 of the presented papers are indexed individually. (J.P.N.)

  18. Proceedings of the third IEA international workshop on beryllium technology for fusion

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, Hiroshi; Okamoto, Makoto [eds.

    1998-01-01

    This report is the Proceedings of the Third International Energy Agency International Workshop on Beryllium Technology for Fusion. The workshop was held on October 22-24, 1997, at the Sangyou Kaikan in Mito City with 68 participants who attended from the Europe, the Russian Federation, the Kazakstan, the United States and Japan. The topics for papers were arranged into 9 sessions; beryllium applications for ITER, production and characterization, chemical compatibility and corrosion, forming and joining, plasma/tritium interactions, beryllium coating, first wall applications, neutron irradiation effects, health and safety. To utilize beryllium in the pebble type blanket, a series of discussions were intensified in multiple view points such as the swelling, He/T release from beryllium pebble irradiated up to high He content, effective thermal conductivity, tritium permeation and coating, and fabrication cost, and so on. As the plasma facing material, life time of beryllium and coated beryllium, dust and particle production, joining, waste treatment, mechanical properties and deformation by swelling were discussed as important issues. Especially, it was recognized throughout the discussions that the comparative study by the different researchers should be carried out to establish the reliability of the data reported in the workshop and in others. To enhance the comparative study, the world wide collaboration for the relative evaluation of the beryllium was proposed by the International Organization Committee and the proposal was approved by all of the participants. The 45 of the presented papers are indexed individually. (J.P.N.)

  19. Tritium release from highly neutron irradiated constrained and unconstrained beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Chakin, V., E-mail: vladimir.chakin@kit.edu; Rolli, R.; Vladimirov, P.; Moeslang, A.

    2015-06-15

    Highlights: • For the irradiated constrained beryllium pebbles, the tritium release occurs easier than for the unconstrained ones. • Tritium retention in the irradiated constrained and unconstrained beryllium pebbles decreases with increasing irradiation temperature. • Formation of sub-grains in the constrained beryllium pebbles facilitate the open porosity network formation. - Abstract: Beryllium is the reference neutron multiplier material in the Helium Cooled Pebble Bed (HCPB) breeding blanket of fusion power plants. Significant tritium inventory accumulated in beryllium as a result of neutron-induced transmutations could become a safety issue for the operation of such blankets as well as for the nuclear waste utilization. To provide a related materials database, a neutron irradiation campaign of beryllium pebbles with diameters of 0.5 and 1 mm at 686–1006 K, the HIDOBE-01 experiment, has been performed in the HFR in Petten, the Netherlands, producing up to 3020 appm helium and 298 appm tritium. Thermal desorption tests of irradiated unconstrained and constrained beryllium pebbles were performed in a purge gas flow using a quadrupole mass-spectrometer (QMS) and an ionization chamber. Compared to unconstrained pebbles, constrained beryllium pebbles have an enhanced tritium release at all temperatures investigated. Small elongated sub-grains formed under irradiation in the constrained pebbles promote formation of numerous channels for facilitated tritium release.

  20. Reduction evaporation of BeO to provide a beryllium metal sample for accelerator radiometric dating

    International Nuclear Information System (INIS)

    A technique is described for preparing beryllium metal samples from beryllium oxide for use in accelerator ion sources. These samples are used to measure minute 10Be/9Be ratios for radiometric dating at the University of Washington tandem Van de Graaff accelerator. (orig.)

  1. Protection of beryllium metal against microbial influenced corrosion using silane self-assembled monolayers

    Science.gov (United States)

    Vaidya, Rajendra U.; Deshpande, Alina; Hersman, Larry; Brozik, Susan M.; Butt, Darryl

    1999-08-01

    The effectiveness of a self-assembled silane monolayer as protection for beryllium against microbiologically influenced corrosion (MIC) was demonstrated. Four-point bend tests on coated and uncoated beryllium samples were conducted after microbiological exposures, and the effectiveness of these coatings as MIC protection was reported through mechanical property evaluations. Application of the silane monolayer to the beryllium surfaces was found to prevent degradation of the failure strength and displacement-to-failure of beryllium in bending. In contrast, the uncoated beryllium samples exhibited a severe reduction in these mechanical properties in the presence of the marine Pseudomonas bacteria. The potentiodynamic measurements showed that both the uncoated and coated samples pitted at the open-circuit potential. However, the size and distribution of the corrosion pits formed on the surface of the beryllium samples were significantly different for the various cases (coated vs uncoated samples exposed to control vs inoculated medium). This study demonstrates the following: (1) the deleterious effects of MIC on the mechanical properties of beryllium and (2) the potential for developing fast, easy, and cost-effective MIC protection for beryllium metal using silane self-assemblies.

  2. 10 CFR 71.23 - General license: Plutonium-beryllium special form material.

    Science.gov (United States)

    2010-01-01

    ... requirements of 49 CFR 173.417(a). (b) The general license applies only to a licensee who has a quality... 10 Energy 2 2010-01-01 2010-01-01 false General license: Plutonium-beryllium special form material... RADIOACTIVE MATERIAL General Licenses § 71.23 General license: Plutonium-beryllium special form material....

  3. Correlates of Performance of Healthcare Workers in Emergency, Triage, Assessment and Treatment plus Admission Care (ETAT+ Course in Rwanda: Context Matters.

    Directory of Open Access Journals (Sweden)

    Celestin Hategekimana

    Full Text Available The Emergency, Triage, Assessment and Treatment plus Admission care (ETAT+ course, a comprehensive advanced pediatric life support course, was introduced in Rwanda in 2010 to facilitate the achievement of the fourth Millennium Development Goal. The impact of the course on improving healthcare workers (HCWs knowledge and practical skills related to providing emergency care to severely ill newborns and children in Rwanda has not been studied.To evaluate the impact of the ETAT+ course on HCWs knowledge and practical skills, and to identify factors associated with greater improvement in knowledge and skills.We used a one group, pre-post test study using data collected during ETAT+ course implementation from 2010 to 2013. The paired t-test was used to assess the effect of ETAT+ course on knowledge improvement in participating HCWs. Mixed effects linear and logistic regression models were fitted to explore factors associated with HCWs performance in ETAT+ course knowledge and practical skills assessments, while accounting for clustering of HCWs in hospitals.374 HCWs were included in the analysis. On average, knowledge scores improved by 22.8/100 (95% confidence interval (CI 20.5, 25.1. In adjusted models, bilingual (French & English participants had a greater improvement in knowledge 7.3 (95% CI 4.3, 10.2 and higher odds of passing the practical skills assessment (adjusted odds ratio (aOR = 2.60; 95% CI 1.25, 5.40 than those who were solely proficient in French. Participants who attended a course outside of their health facility had higher odds of passing the skills assessment (aOR = 2.11; 95% CI 1.01, 4.44 than those who attended one within their health facility.The current study shows a positive impact of ETAT+ course on improving participants' knowledge and skills related to managing emergency pediatric and neonatal care conditions. The findings regarding key factors influencing ETAT+ course outcomes demonstrate the importance of considering key

  4. The Foreign Workers and Foreign Workers' German.

    Science.gov (United States)

    Blackshire-Belay, Carol

    Foreign Workers' German (FWG) refers to the acquired German language skills of workers from various countries who were recruited to West Germany between 1955 and 1973 to fill menial, undesirable jobs. Contact between these workers and native German speakers was limited because of the nature of the foreigners' work, the tendency toward residential…

  5. Deformation behaviour of fine grained high purity beryllium - influence of fabrication parameters, temperature and copper additions

    International Nuclear Information System (INIS)

    The deformation behaviour of high-purity beryllium was tested on hot isostatically pressed samples of different initial grain size and compared with material manufactured commercially from pure beryllium and with beryllium-copper alloys containing 0.44, 1.1 and 2.1 at.% copper. Initial grain size of these high purity material was 0C. Grain structure of the samples was subsequently analysed by light, rastor and transmission electron microscopy. The influence of copper additions on deformation of high-purity beryllium was analysed. A further aim of this study was to investigate, by suitable methods, the mode of action of relevant impurities and to throw light on their influence on grain formation. This should enable reliable information to be provided for the manufacture of high-purity beryllium which, in turn, will lead to an improvement in ductility. (orig./IHOE)

  6. Preliminary irradiation test for new material selection on lifetime extension of beryllium reflector

    International Nuclear Information System (INIS)

    Beryllium has been utilized as a moderator and/or reflector in Japan Materials Testing Reactor (JMTR), because of nuclear properties of beryllium, low neutron capture and high neutron scattering cross sections. At present, the amount of irradiated beryllium frames in JMTR is about 2 tons in the JMTR canal. In this study, preliminary irradiation test was performed from 162nd to 165th operation cycles of JMTR as irradiation and PIE technique development for lifetime expansion of beryllium frames. The design study of irradiation capsule, development of dismount device of irradiation capsule and the high accuracy size measurement device were carried out. The PIEs such as tensile tests, metallurgical observation, and size change measurement were also carried out with two kinds of irradiated beryllium metals (S-200F and S-65C). (author)

  7. Detection of beryllium treatment of natural sapphires by NRA

    Science.gov (United States)

    Gutiérrez, P. C.; Ynsa, M.-D.; Climent-Font, A.; Calligaro, T.

    2010-06-01

    Since the 1990's, artificial treatment of natural sapphires (Al 2O 3 crystals coloured by impurities) by diffusion of beryllium at high temperature has become a growing practice. This process permits to enhance the colour of these gemstones, and thus to increase their value. Detection of such a treatment - diffusion of tens of μg/g of beryllium in Al 2O 3 crystals - is usually achieved using high sensitivity techniques like laser-ablation inductively coupled plasma mass spectrometry (LA-ICP/MS) or laser-induced breakdown spectrometry (LIBS) which are unfortunately micro-destructive (leaving 50-100-μm diameter craters on the gems). The simple and non-destructive alternative method proposed in this work is based on the nuclear reaction 9Be(α, nγ) 12C with an external helium ion beam impinging on the gem directly placed in air. The 4439 keV prompt γ-ray tagging Be atoms are detected with a high efficiency bismuth germanate scintillator. Beam dose is monitored using the 2235 keV prompt γ-ray produced during irradiation by the aluminium of the sapphire matrix through the 27Al(α, pγ) 30Si nuclear reaction. The method is tested on a series of Be-treated sapphires previously analyzed by LA-ICP/MS to determine the optimal conditions to obtain a peak to background appropriate to reach the required μg/g sensitivity. Using a 2.8-MeV external He beam and a beam dose of 200 μC, beryllium concentrations from 5 to 16 μg/g have been measured in the samples, with a detection limit of 1 μg/g.

  8. Detection of beryllium treatment of natural sapphires by NRA

    Energy Technology Data Exchange (ETDEWEB)

    Gutierrez, P.C., E-mail: carolina.gutierrez@uam.e [Centro de Micro-Analisis de Materiales (CMAM), Universidad Autonoma de Madrid, Campus de Cantoblanco, 28049 Madrid (Spain); Ynsa, M.-D.; Climent-Font, A. [Centro de Micro-Analisis de Materiales (CMAM), Universidad Autonoma de Madrid, Campus de Cantoblanco, 28049 Madrid (Spain); Dpto. Fisica Aplicada C-12, Universidad Autonoma de Madrid, Campus de Cantoblanco, 28049 Madrid (Spain); Calligaro, T. [Centre de Recherche et de Restauration des musees de France C2RMF, CNRS-UMR171, 14 quai Francois Mitterrand, 75001 Paris (France)

    2010-06-15

    Since the 1990's, artificial treatment of natural sapphires (Al{sub 2}O{sub 3} crystals coloured by impurities) by diffusion of beryllium at high temperature has become a growing practice. This process permits to enhance the colour of these gemstones, and thus to increase their value. Detection of such a treatment - diffusion of tens of {mu}g/g of beryllium in Al{sub 2}O{sub 3} crystals - is usually achieved using high sensitivity techniques like laser-ablation inductively coupled plasma mass spectrometry (LA-ICP/MS) or laser-induced breakdown spectrometry (LIBS) which are unfortunately micro-destructive (leaving 50-100-{mu}m diameter craters on the gems). The simple and non-destructive alternative method proposed in this work is based on the nuclear reaction {sup 9}Be({alpha}, n{gamma}){sup 12}C with an external helium ion beam impinging on the gem directly placed in air. The 4439 keV prompt {gamma}-ray tagging Be atoms are detected with a high efficiency bismuth germanate scintillator. Beam dose is monitored using the 2235 keV prompt {gamma}-ray produced during irradiation by the aluminium of the sapphire matrix through the {sup 27}Al({alpha}, p{gamma}){sup 30}Si nuclear reaction. The method is tested on a series of Be-treated sapphires previously analyzed by LA-ICP/MS to determine the optimal conditions to obtain a peak to background appropriate to reach the required {mu}g/g sensitivity. Using a 2.8-MeV external He beam and a beam dose of 200 {mu}C, beryllium concentrations from 5 to 16 {mu}g/g have been measured in the samples, with a detection limit of 1 {mu}g/g.

  9. Model study in chemisorption: atomic hydrogen on beryllium clusters

    Energy Technology Data Exchange (ETDEWEB)

    Bauschlicher, C.W. Jr.

    1976-08-01

    The interaction between atomic hydrogen and the (0001) surface of Be metal has been studied by ab initio electronic structure theory. Self-consistent-field (SCF) calculations have been performed using minimum, optimized minimum, double zeta and mixed basis sets for clusters as large as 22 Be atoms. The binding energy and equilibrium geometry (the distance to the surface) were determined for 4 sites. Both spatially restricted (the wavefunction was constrained to transform as one of the irreducible representations of the molecular point group) and unrestricted SCF calculations were performed. Using only the optimized minimum basis set, clusters containing as many as 22 beryllium atoms have been investigated. From a variety of considerations, this cluster is seen to be nearly converged within the model used, providing the most reliable results for chemisorption. The site dependence of the frequency is shown to be a geometrical effect depending on the number and angle of the bonds. The diffusion of atomic hydrogen through a perfect beryllium crystal is predicted to be energetically unfavorable. The cohesive energy, the ionization energy and the singlet-triplet separation were computed for the clusters without hydrogen. These quantities can be seen as a measure of the total amount of edge effects. The chemisorptive properties are not related to the total amount of edge effects, but rather the edge effects felt by the adsorbate bonding berylliums. This lack of correlation with the total edge effects illustrates the local nature of the bonding, further strengthening the cluster model for chemisorption. A detailed discussion of the bonding and electronic structure is included. The remaining edge effects for the Be/sub 22/ cluster are discussed.

  10. Use of notched beams to establish fracture criteria for beryllium

    International Nuclear Information System (INIS)

    The fracture of an improved form of pure beryllium was studied under triaxial tensile stresses. This state of stress was produced by testing notched beams, which were thick enough to be in a state of plane strain at the center. A plane strain, elastic-incremental plasticity finite element program was then used to determine the stress and strain distributions at fracture. A four-point bend fixture was used to load the specimens. It was carefully designed and manufactured to eliminate virtually all of the shear stresses at the reduced section of the notched beams. The unixial properties were obtained

  11. Beryllium ignition target design for indirect drive NIF experiments

    Science.gov (United States)

    Simakov, A. N.; Wilson, D. C.; Yi, S. A.; Kline, J. L.; Salmonson, J. D.; Clark, D. S.; Milovich, J. L.; Marinak, M. M.

    2016-03-01

    Beryllium (Be) ablator offers multiple advantages over carbon based ablators for indirectly driven NIF ICF ignition targets. These are higher mass ablation rate, ablation pressure and ablation velocity, lower capsule albedo, and higher thermal conductivity at cryogenic temperatures. Such advantages can be used to improve the target robustness and performance. While previous NIF Be target designs exist, they were obtained a long time ago and do not incorporate the latest improved physical understanding and models based upon NIF experiments. Herein, we propose a new NIF Be ignition target design at 1.45 MJ, 430 TW that takes all this knowledge into account.

  12. Dosage of boron traces in graphite, uranium and beryllium oxide

    International Nuclear Information System (INIS)

    The problem of the dosage of the boron in the materials serving to the construction of nuclear reactors arises of the following way: to determine to about 0,1 ppm close to the quantities of boron of the order of tenth ppm. We have chosen the colorimetric analysis with curcumin as method of dosage. To reach the indicated contents, it is necessary to do a previous separation of the boron and the materials of basis, either by extraction of tetraphenylarsonium fluoborate in the case of the boron dosage in uranium and the beryllium oxide, either by the use of a cations exchanger resin of in the case of graphite. (M.B.)

  13. Technique of beryllium determination using an (α,n) reaction

    International Nuclear Information System (INIS)

    The possibility of detecting small amounts of 9Be using the (α, n) reaction has been investigated. It is shown that at a 210Po α-particle source intensity of 3x108 s-1 for limit of the detectable amount of beryllium is equal to 0.1 μg in the case of recording neutron-gamma (>= 3.6 MeV) coincidences. Other light elements (B, F, Al, Mg, Si etc.) do not produce a noticeable background under such conditions

  14. Double K-shell photoionization of atomic beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Yip, F. L. [Departamento de Quimica, Modulo 13, Universidad Autonoma de Madrid, E-28049 Madrid (Spain); Martin, F. [Departamento de Quimica, Modulo 13, Universidad Autonoma de Madrid, E-28049 Madrid (Spain); Instituto Madrilen(tilde sign)o de Estudios Avanzados en Nanociencia, Cantoblanco, E-28049 Madrid (Spain); McCurdy, C. W. [Department of Chemistry, University of California, Davis, California 95616 (United States); Lawrence Berkeley National Laboratory, Chemical Sciences, and Ultrafast X-ray Science Laboratory, Berkeley, California 94720 (United States); Rescigno, T. N. [Lawrence Berkeley National Laboratory, Chemical Sciences, and Ultrafast X-ray Science Laboratory, Berkeley, California 94720 (United States)

    2011-11-15

    Double photoionization of the core 1s electrons in atomic beryllium is theoretically studied using a hybrid approach that combines orbital and grid-based representations of the Hamiltonian. The {sup 1} S ground state and {sup 1} P final state contain a double occupancy of the 2s valence shell in all configurations used to represent the correlated wave function. Triply differential cross sections are evaluated, with particular attention focused on a comparison of the effects of scattering the ejected electrons through the spherically symmetric valence shell with similar cross sections for helium, representing a purely two-electron target with an analogous initial-state configuration.

  15. Accumulation of tritium in beryllium material under neutron irradiation

    International Nuclear Information System (INIS)

    In the present work the programming code is created on the basis of which the accumulation kinetics of tritium and isotope of He4 in the Be9 sample is analyzed depending on the time. The program is written in C++ programming language and for the calculations Monte Carlo method was applied. This program scoped on the calculation of concentration of helium and tritium in beryllium samples depending on the spectrum of the neutron flux in different experimental reactors such as JMTR, JOYO and IPEN/MB. The processes of accumulation of helium and tritium for each neutron energy spectrum of these reactors were analyzed. (author)

  16. Tritium analyses of COBRA-1A2 beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Baldwin, D.L. [Pacific Northwest National Lab., Richland, WA (United States)

    1998-03-01

    Selected tritium measurements have been completed for the COBRA-1A2 experiment C03 and D03 beryllium pebbles. The completed results, shown in Tables 1, 2, and 3, include the tritium assay results for the 1-mm and 3-mm C03 pebbles, and the 1-mm D03 pebbles, stepped anneal test results for both types of 1-mm pebbles, and the residual analyses for the stepped-anneal specimens. All results have been reported with date-of-count and are not corrected for decay. Stepped-anneal tritium release response is provided in addenda.

  17. Electromagnetic properties of the Beryllium-11 nucleus in Halo EFT

    OpenAIRE

    Hammer H.-W.; Phillips D.R.

    2010-01-01

    We compute electromagnetic properties of the Beryllium-11 nucleus using an effective field theory that exploits the separation of scales in this halo system. We fix the parameters of the EFT from measured data on levels and scattering lengths in the 10Be plus neutron system. We then obtain predictions for the B(E1) strength of the 1/2+ to 1/2− transition in the 11Be nucleus. We also compute the charge radius of the ground state of 11Be. Agreement with experiment within the expected accurac...

  18. Microstructure and mechanical properties of neutron irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Ishitsuka, E.; Kawamura, H. [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment; Terai, T.; Tanaka, S.

    1998-01-01

    Microstructure and mechanical properties of the neutron irradiated beryllium with total fast neutron fluences of 1.3 - 4.3 x 10{sup 21} n/cm{sup 2} (E>1 MeV) at 327 - 616degC were studied. Swelling increased by high irradiation temperature, high fluence, and by the small grain size and high impurity. Obvious decreasing of the fracture stress was observed in the bending test and in small grain specimens which had many helium bubbles on the grain boundary. Decreasing of the fracture stress for small grain specimens was presumably caused by crack propagation on the grain boundaries which weekend by helium bubbles. (author)

  19. Assessment of potential dermal and inhalation exposure of workers to the insecticide imidacloprid using whole-body dosimetry in China

    Institute of Scientific and Technical Information of China (English)

    Lidong Cao; BO Chen; Li Zheng; Dongwei Wang; Feng Liu; Qiliang Huang

    2015-01-01

    In China,although improvements to the pesticide registration process have been made in last thirty years,no occupational exposure data are required to obtain a commercial license for a pesticide product.Consequently,notably little research has been conducted to establish an exposure assessment procedure in China.The present study monitored the potential dermal operator exposure from knapsack electric sprayer wheat field application of imidacloprid in Liaocheng City,Shandong Province and in Xinxiang City,Henan Province,China,using whole-body dosimetry.The potential inhalation exposure was determined using a personal air pump and XAD-2 sample tubes.The analytical method was developed and validated,including such performance parameters as limits of detection and quantification,linear range,recovery and precision.The total potential dermal and inhalation exposures were 14.20,16.80,15.39 and 20.78 mL/hr,respectively,for the four operators in Liaocheng and Xinxiang,corresponding to 0.02% to 0.03% of the applied volume of spray solution.In all trials,the lower part (thigh,lower leg) of the body was the most contaminated,accounting for approximately 76% to 88% of the total exposure.The inhalation exposure was less than 1% of the total exposure.Such factors as the application pattern,crop type,spray equipment,operator experience and climatic conditions have been used to explain the exposure distribution over the different parts of the body.As indicated by the calculated Margin of Exposure,the typical wheat treatment scenarios when a backpack sprayer was used are considered to be safe in terms of imidacloprid exposure.

  20. Organizational Commitment and Turnover Intention in Low-Skilled Immigrant Workers in Thailand: An Empirical Assessment of Need Satisfaction, Job Satisfaction and Overall Life Satisfaction Factors

    OpenAIRE

    Kevalin Puangyoykeaw; Yuko Nishide

    2015-01-01

    As a result of its pace of development, Thailand is now facing a shortage of low-skilled labour, especially in labour-intensive industries. An influx of workers from neighbouring countries, especially Myanmar, is now substituting for low-skilled nationals. The challenge of how organizations can retain and motivate low-skilled workers remains a major issue. The scarce literature and little focus on how low-skilled workers can be managed have given rise to this paper. In this paper, we aim to e...

  1. Safety assessment for ethanol-based topical antiseptic use by health care workers: Evaluation of developmental toxicity potential.

    Science.gov (United States)

    Maier, Andrew; Ovesen, Jerald L; Allen, Casey L; York, Raymond G; Gadagbui, Bernard K; Kirman, Christopher R; Poet, Torka; Quiñones-Rivera, Antonio

    2015-10-01

    Ethanol-based topical antiseptic hand rubs, commonly referred to as alcohol-based hand sanitizers (ABHS), are routinely used as the standard of care to reduce the presence of viable bacteria on the skin and are an important element of infection control procedures in the healthcare industry. There are no reported indications of safety concerns associated with the use of these products in the workplace. However, the prevalence of such alcohol-based products in healthcare facilities and safety questions raised by the U.S. FDA led us to assess the potential for developmental toxicity under relevant product-use scenarios. Estimates from a physiologically based pharmacokinetic modeling approach suggest that occupational use of alcohol-based topical antiseptics in the healthcare industry can generate low, detectable concentrations of ethanol in blood. This unintended systemic dose probably reflects contributions from both dermal absorption and inhalation of volatilized product. The resulting internal dose is low, even under hypothetical, worst case intensive use assumptions. A significant margin of exposure (MOE) exists compared to demonstrated effect levels for developmental toxicity under worst case use scenarios, and the MOE is even more significant for typical anticipated occupational use patterns. The estimated internal doses of ethanol from topical application of alcohol-based hand sanitizers are also in the range of those associated with consumption of non-alcoholic beverages (i.e., non-alcoholic beer, flavored water, and orange juice), which are considered safe for consumers. Additionally, the estimated internal doses associated with expected exposure scenarios are below or in the range of the expected internal doses associated with the current occupational exposure limit for ethanol set by the Occupational Safety and Health Administration. These results support the conclusion that there is no significant risk of developmental or reproductive toxicity from

  2. The mechanism for production of beryllium fluoride from the product of ammonium fluoride processing of beryllium- containing raw material

    Science.gov (United States)

    Kraydenko, R. I.; Dyachenko, A. N.; Malyutin, L. N.; Petlin, I. V.

    2016-06-01

    The technique of fluorite-phenacite-bertrandite ores from Russian Ermakovskoe deposit processing by ammonium bifluoride is described. To determine the temperature mode and the thermal dissociation mechanism of ammonium tetrafluoroberyllate (the product of ammonium-fluoride leaching of the ore) the TG/DTA have been carried out. By IR spectroscopy and XRD the semi-products of ammonium tetrafluoroberyllate thermal dissociation have been identified. The hygroscopic low-temperature beryllium fluoride forms higher than 380°C. The less hydroscopic form of BeF2 have been produced at 600°C.

  3. Worker participation - the Netherlands

    NARCIS (Netherlands)

    Kwantes, J.H.

    2014-01-01

    Worker participation relates to the involvement of workers in the management decision-making processes. In this article attention is focused on worker participation related to occupational safety and health in the Netherlands. Worker participation can refer either to direct or indirect participation

  4. Influence of neutron irradiation on the tritium retention in beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Rolli, R.; Ruebel, S.; Werle, H. [Forschungszentrum Karlsruhe, Inst. fuer Neutronenphysik und Reaktortechnik, Karlsruhe (Germany); Wu, C.H.

    1998-01-01

    Carbon-based materials and beryllium are the candidates for protective layers on the components of fusion reactors facing plasma. In contact with D-T plasma, these materials absorb tritium, and it is anticipated that tritium retention increases with the neutron damage due to neutron-induced traps. Because of the poor data base for beryllium, the work was concentrated on it. Tritium was loaded into the samples from stagnant T{sub 2}/H{sub 2} atmosphere, and afterwards, the quantity of the loaded tritium was determined by purged thermal annealing. The specification of the samples is shown. The samples were analyzed by SEM before and after irradiation. The loading and the annealing equipments are contained in two different glove boxes with N{sub 2} inert atmosphere. The methods of loading and annealing are explained. The separation of neutron-produced and loaded tritium and the determination of loaded tritium in irradiated samples are reported. Also the determination of loaded tritium in unirradiated samples is reported. It is evident that irradiated samples contained much more loaded tritium than unirradiated samples. The main results of this investigation are summarized in the table. (K.I.)

  5. Remarkable Hydrogen Storage on Beryllium Oxide Clusters: First Principles Calculations

    CERN Document Server

    Shinde, Ravindra

    2016-01-01

    Since the current transportation sector is the largest consumer of oil, and subsequently responsible for major air pollutants, it is inevitable to use alternative renewable sources of energies for vehicular applications. The hydrogen energy seems to be a promising candidate. To explore the possibility of achieving a solid-state high-capacity storage of hydrogen for onboard applications, we have performed first principles density functional theoretical calculations of hydrogen storage properties of beryllium oxide clusters (BeO)$_{n}$ (n=2 -- 8). We observed that polar BeO bond is responsible for H$_{2}$ adsorption. The problem of cohesion of beryllium atoms does not arise, as they are an integral part of BeO clusters. The (BeO)$_{n}$ (n=2 -- 8) adsorbs 8--12 H$_{2}$ molecules with an adsorption energy in the desirable range of reversible hydrogen storage. The gravimetric density of H$_{2}$ adsorbed on BeO clusters meets the ultimate 7.5 wt% limit, recommended for onboard practical applications. In conclusion,...

  6. Microstructural Characterization of Beryllium Treated Al-Si Alloys

    Directory of Open Access Journals (Sweden)

    M. F. Ibrahim

    2015-01-01

    Full Text Available The present study was carried out on B356 and B357 alloys using the thermal analysis technique. Metallographic samples prepared from these castings were examined using optical microscopy and FESEM. Results revealed that beryllium causes partial modification of the eutectic Si, similar to that reported for magnesium additions. Addition of 0.8 wt.% Mg reduces the eutectic temperature by ~10°C. During solidification of alloys containing high levels of Fe and Mg, but no Sr, formation of a Be-Fe phase was detected at 611°C, close to that of α-Al. The Be-Fe phase precipitates in script-like form at or close to the β-Al5SiFe platelets. A new reaction, composed of fine particles of Si and π-Fe phase, was observed to occur near the end of solidification in high Mg-, high Fe-, and Be-containing alloys. The amount of this reaction decreased with the addition of Sr. Occasionally, Be-containing phase particles were observed as part of the reaction. Addition of Be has a noticeable effect on decreasing the β-Al5FeSi platelet length; this effect may be enhanced by addition of Sr. Beryllium addition also results in precipitation of the β-Al5FeSi phase in nodular form, which lowers its harmful effects on the alloy mechanical properties.

  7. A non-chemical spectroscopic determination of atmospheric beryllium

    International Nuclear Information System (INIS)

    Beryllium in the atmosphere is determined by emission spectroscopy using a non-chemical method of analysis. Long term effects of beryllium poisoning result in respiratory and skin disease, and this is partly reflected by the low threshold limits (0.002 mg/m3). In comparison the threshhold values for lead and cadmium are 0.2 and 0.16 mg/m3 respectively. Air samples are collected at 2 litres/ minute using cellulose filters, and sampling time is dependent on the individual process being monitored, but can be as short as five minutes, eg. dental laboratories. The filters are initially divided in two parts, and one portion is carefully pelletised using a steel press. The pellet is placed in an electrode cup and 'wetted' using isopropanol and ethylene glycol. Wetting is necessary because the pellets tended to explode out of the arcing zone. Calibration graphs were produced using an internal cobalt standard, and the 234.8 nm, 313.0 nm emission lines were used. No spectral and inter-element effects were observed, and the minimum detection limit was one nanogram. Under normal working conditions a 25% precision was obtained. (author)

  8. Calculations for electron-impact excitation and ionization of beryllium

    CERN Document Server

    Zatsarinny, Oleg; Fursa, Dmitry V; Bray, Igor

    2016-01-01

    The B-spline R-matrix and the convergent close-coupling methods are used to study electron collisions with neutral beryllium over an energy range from threshold to 100 eV. Coupling to the target continuum significantly affects the results for transitions from the ground state, but to a lesser extent the strong transitions between excited states. Cross sections are presented for selected transitions between low-lying physical bound states of beryllium, as well as for elastic scattering, momentum transfer, and ionization. The present cross sections for transitions from the ground state from the two methods are in excellent agreement with each other, and also with other available results based on nonperturbative convergent pseudo-state and time-dependent close-coupling models. The elastic cross section at low energies is dominated by a prominent shape resonance. The ionization from the $(2s2p)^3P$ and $(2s2p)^1P$ states strongly depends on the respective term. The current predictions represent an extensive set o...

  9. Steam chemical reactivity of plasma-sprayed beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Anderl, R.A.; Pawelko, R.J.; Smolik, G.R. [Lockheed Martin Idaho Technologies Co., Idaho Falls, ID (United States). Idaho National Engineering and Environmental Lab.; Castro, R.G. [Los Alamos National Lab., NM (United States)

    1998-07-01

    Plasma-spraying with the potential for in-situ repair makes beryllium a primary candidate for plasma facing and structural components in experimental magnetic fusion machines. Deposits with good thermal conductivity and resistance to thermal cycling have been produced with low pressure plasma-spraying (LPPS). A concern during a potential accident with steam ingress is the amount of hydrogen produced by the reactions of steam with hot components. In this study the authors measure the reaction rates of various deposits produced by LPPS with steam from 350 C to above 1,000 C. They correlate these reaction rates with measurements of density, open porosity and BET surface areas. They find the reactivity to be largely dependent upon effective surface area. Promising results were obtained below 600 C from a 94% theoretical dense (TD) deposit with a BET specific surface area of 0.085 m{sup 2}/g. Although reaction rates were higher than those for dense consolidated beryllium they were substantially lower, i.e., about two orders of magnitude, than those obtained from previously tested lower density plasma-sprayed deposits.

  10. Increased Suicide Risk among Workers following Toxic Metal Exposure at the Paducah Gaseous Diffusion Plant From 1952 to 2003: A Cohort Study

    Directory of Open Access Journals (Sweden)

    D Tollerud

    2011-09-01

    Full Text Available Background: Suicide is a problem worldwide and occupation is an important risk factor. In the last decade, 55 200 deaths in the US were attributed to occupational risk factors. Objective: To determine if toxic metal exposure was associated with suicide risk among Paducah gaseous diffusion plant (PGDP workers. Methods: We assembled a cohort of 6820 nuclear industry workers employed from 1952 to 2003. A job-specific exposure matrix (JEM was used to determine metal exposure likelihood. Uranium exposure was also assessed by urinalysis. All suicide/self-injury International Classification for Disease (ICD codes were used to identify suicides. Standardized mortality ratios (SMR, odds ratios (OR, and hazard ratios (HR were used to estimate suicide risk. Results: PGDP suicide victims typically were younger white men. Within exposure likelihood categories, several suicide SMRs were typically elevated for several metals. Only beryllium exposure likelihood was associated with an increased HR. Uranium urine concentration was associated with an elevated suicide risk after stratification by urinalysis frequency. Conclusion: Suicide risk is associated with uranium exposure.

  11. 女用安全套在暗娼中的应用评价%Assessment of female condom use in female sex workers

    Institute of Scientific and Technical Information of China (English)

    蒋辽远; 闫红静; 郭红梅; 冯景文; 孙祖峰; 杨蒙蒙; 李澜

    2015-01-01

    Objective:To assess the influence of condom promotion on female condom use in female sex workers ( FSW) . Methods:Female condom use was promoted among FSWs in targeted entertainment estab-lishments. Results:After intervention, condom usage rate was increased from 74.8% to 98.8% in the last sex contact and from 9. 5% to 87. 7% in the last month. The female condom use was increased from 1. 4% to 13.8%. Conclusion:Female condom intervention can promotes condom use.%目的::评价暗娼( FSW)中女用安全套干预措施对提高安全套使用率的影响。方法:对目标场所FSW女用安全套的使用进行干预促进。结果:经干预后,FSW最近1次发生性行为时安全套使用率从74.8%上升到98.8%;最近1个月使用率从9.5%上升到87.7%,其中女用安全套使用比例从1.4%上升到13.8%。结论:女用安全套干预措施可以明显提高该人群安全套的使用率。

  12. A rapid assessment of a community health worker pilot programme to improve the management of hypertension and diabetes in Emfuleni sub-district of Gauteng Province, South Africa

    Directory of Open Access Journals (Sweden)

    Jane Goudge

    2013-01-01

    Full Text Available Background: Non-communicable diseases (NCD and infectious chronic illnesses are recognised as significant contributing factors to the burden of disease globally, specifically in South Africa, yet clinical management is often poor. The involvement of community health workers (CHWs in TB and HIV care in South Africa, and other low- and middle-income settings, suggests that they could make an important contribution in the management of NCDs. Objectives: Using a rapid assessment, this study examines the outcomes of a pilot CHW programme to improve the management of hypertension and diabetes in Gauteng province, South Africa. Methods: A record review compared outcomes of patients receiving home visits (n56 with a control group (n168 attending the clinic, matched, as far as possible, on age, gender, and condition. Focus group discussions and semi-structured interviews with CHWs, patients, district, clinic, and NGO staff were used to obtain descriptions of the functioning of the programme and patient experiences. Results: Despite the greater age and co-morbidity among those in the pilot programme, the findings suggest that control of hypertension was improved by CHW home visits in comparison to usual clinic care. However, too few doctor visits, insufficient monitoring of patient outcomes by clinic staff, and a poor procurement process for supplies required by the CHWs hampered the programme's activities. Conclusion: The role of CHWs in the management of hypertension should be given greater consideration, with larger studies being conducted to provide more robust evidence. Adequate training, supervision, and operational support will be required to ensure success of any CHW programme.

  13. VOC contamination in hospital, from stationary sampling of a large panel of compounds, in view of healthcare workers and patients exposure assessment.

    Directory of Open Access Journals (Sweden)

    Vincent Bessonneau

    Full Text Available BACKGROUND: We aimed to assess, for the first time, the nature of the indoor air contamination of hospitals. METHODS AND FINDINGS: More than 40 volatile organic compounds (VOCs including aliphatic, aromatic and halogenated hydrocarbons, aldehydes, alcohols, ketones, ethers and terpenes were measured in a teaching hospital in France, from sampling in six sampling sites--reception hall, patient room, nursing care, post-anesthesia care unit, parasitology-mycology laboratory and flexible endoscope disinfection unit--in the morning and in the afternoon, during three consecutive days. Our results showed that the main compounds found in indoor air were alcohols (arithmetic means ± SD: 928±958 µg/m³ and 47.9±52.2 µg/m³ for ethanol and isopropanol, respectively, ethers (75.6±157 µg/m³ for ether and ketones (22.6±20.6 µg/m³ for acetone. Concentrations levels of aromatic and halogenated hydrocarbons, ketones, aldehydes and limonene were widely variable between sampling sites, due to building age and type of products used according to health activities conducted in each site. A high temporal variability was observed in concentrations of alcohols, probably due to the intensive use of alcohol-based hand rubs in all sites. Qualitative analysis of air samples led to the identification of other compounds, including siloxanes (hexamethyldisiloxane, octamethyltrisiloxane, decamethylcyclopentasiloxane, anesthetic gases (sevoflurane, desflurane, aliphatic hydrocarbons (butane, esters (ethylacetate, terpenes (camphor, α-bisabolol, aldehydes (benzaldehyde and organic acids (benzoic acid depending on sites. CONCLUSION: For all compounds, concentrations measured were lower than concentrations known to be harmful in humans. However, results showed that indoor air of sampling locations contains a complex mixture of VOCs. Further multicenter studies are required to compare these results. A full understanding of the exposure of healthcare workers and patients

  14. Development of radiation resistant grades of beryllium for nuclear and fusion facilities

    Energy Technology Data Exchange (ETDEWEB)

    Kupriyanov, I.B.; Gorokhov, V.A.; Nikolaev, G.N. [Russia Research Institute of Inorganic Materials, Moscow (Russian Federation)

    1995-09-01

    R&D results on beryllium with high radiation resistance obtained recently are described in this report. The data are presented on nine different grades of isotropic beryllium manufactured by VNIINM and distinguished by both initial powder characteristics and properties of billets, made of these powders. The average grain size of the investigated beryllium grades varied from 8 to 26 {mu}m, the content of beryllium oxide was 0.9 - 3.9 wt.%, the dispersity of beryllium oxide - 0.04 - 0.5 {mu}m, tensile strength -- 250 - 650 MPa. All materials were irradiated in SM - 2 reactor over the temperature range 550 - 780{degrees}C. The results of the investigation showed, that HIP beryllium grades are less susceptible to swelling at higher temperatures in comparison with hot pressed and extruded grades. Beryllium samples, having the smallest grain size, demonstrated minimal swelling, which was less than 0.8 % at 750{degrees}C and Fs = 3.7 {center_dot}10{sup 21} cm{sup -2} (E>0.1 MeV). The mechanical properties, creep and microstructure parameters, measured before and after irradiation, are presented.

  15. The development and advantages of beryllium capsules for the National Ignition Facility

    International Nuclear Information System (INIS)

    Capsules with beryllium ablators have long been considered as alternatives to plastic for the National Ignition Facility laser; now the superior performance of beryllium is becoming well substantiated. Beryllium capsules have the advantages of relative insensitivity to instability growth, low opacity, high tensile strength, and high thermal conductivity. 3-D calculation with the HYDRA code NTIS Document No. DE-96004569 (M. M. Marinak et.al. in UCRL-LR-105821-95-3) confirm 2-D LASNEX U. B. Zimmerman and W. L. Kruer, Comments Plasmas Phys. Controlled Thermonucl. Fusion, 2, 51(2975) results that particular beryllium capsule designs are several times less sensitive than the CH point design to instability growth from DT ice roughness. These capsule designs contain more ablator mass and leave some beryllium unablated at ignition. By adjusting the level of copper dopant, the unablated mass can increase or decrease, with a corresponding decrease or increase in sensitivity to perturbations. A plastic capsule with the same ablator mass as the beryllium and leaving the same unablated mass also shows this reduced perturbation sensitivity. Beryllium's low opacity permits the creation of 250 eV capsule designs. Its high tensile strength allows it to contain DT fuel at room temperature. Its high thermal conductivity simplifies cryogenic fielding

  16. Is audio computer-assisted self-interview (ACASI useful in risk behaviour assessment of female and male sex workers, Mombasa, Kenya?

    Directory of Open Access Journals (Sweden)

    Elisabeth M van der Elst

    Full Text Available BACKGROUND: Audio computer-assisted self-interview (ACASI may elicit more frequent reporting of socially sensitive behaviours than face-to-face (FtF-interview. However, no study compared responses to both methods in female and male sex workers (FSW; MSW in Africa. METHODOLOGY/PRINCIPAL FINDINGS: We sequentially enrolled adults recruited for an HIV-1 intervention trial into a comparative study of ACASI and FtF-interview, in a clinic near Mombasa, Kenya. Feasibility and acceptability of ACASI, and a comparative analysis of enrolment responses between ACASI and FtF on an identical risk assessment questionnaire were evaluated. In total, 139 women and 259 men, 81% of eligible cohort participants, completed both interviews. ACASI captured a higher median number of regular (2 vs. 1, p<0.001, both genders and casual partners in the last week (3 vs. 2, p = 0.04 in women; 2 vs. 1, p<0.001 in men. Group sex (21.6 vs. 13.5%, p<0.001, in men, intravenous drug use (IDU; 10.8 vs. 2.3%, p<0.001 in men; 4.4 vs. 0%, p = 0.03 in women, and rape (8.9 vs. 3.9%, p = 0.002, in men were reported more frequently in ACASI. A surprisingly high number of women reported in ACASI that they had paid for sex (49.3 vs. 5.8%, p<0.001. Behaviours for recruitment (i.e. anal sex, sex work, sex between males were reported less frequently in ACASI. The majority of women (79.2% and men (69.7% felt that answers given in ACASI were more honest. Volunteers who were not able to take ACASI (84 men, and 37 women mostly lacked reading skills. CONCLUSIONS/SIGNIFICANCE: About 1 in 5 cohort participants was not able to complete ACASI, mostly for lack of reading skills. Participants who completed ACASI were more likely to report IDU, rape, group sex, and payment for sex by women than when asked in FtF interview. ACASI appears to be a useful tool for high risk behaviour assessments in the African context.

  17. The structure and the Raman vibrational spectrum of the beryllium aquacation.

    Science.gov (United States)

    Rozmanov, Dmitry A; Sizova, Olga V; Skripkin, Mikhail Yu; Burkov, Kim A

    2005-11-01

    The experimental Raman vibrational spectrum of the 5.94 m water solution of the beryllium(II) chloride has been acquired. Theoretical frequencies, infrared and Raman intensities of the vibrational spectrum of the beryllium cation tetrahydrate have been calculated by means of quantum chemical approach. The peaks of the experimental spectrum have been assigned on the basis of the results of the quantum-chemical calculations. It has been shown that the hydrating surrounding of the aquacation increases effectively the frequency of the beryllium-oxygen stretching vibration by 16% in comparison with the free complex.

  18. Conditions for preparation of ultrapure beryllium by electrolytic refining in molten alkali-metal chlorides

    Energy Technology Data Exchange (ETDEWEB)

    Wohlfarth, Hagen

    1982-02-01

    Electrolytic refining is regarded as the most suitable process for the production of beryllium with impurity contents below 1 at.-ppM. Several parameters are important for electrolytic refining of beryllium in a BeCl/sub 2/-containing LiCl-KCl melt: current density, BeCl/sub 2/ content, electrolyte temperature, composition of the unpurified beryllium and impurity-ion concentrations in the melt, as well as apparatus characteristics such as rotation speed of the cathode and condition of the crucible material. These factors were studied and optimized such that extensive removal of the maximum number of accompanying and alloying elements was achieved.

  19. Study of beryllium redeposition under bombardment by high intensity -low energy- hydrogen ion beams

    Energy Technology Data Exchange (ETDEWEB)

    Gureev, V.M.; Guseva, M.I.; Danelyan, L.S. [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation)] [and others

    1998-01-01

    The results of studying the erosion of beryllium under an effect of intense ion fluxes with the energy of 250 eV, at the fluences {approx}10{sup 2}1 cm{sup -2}, at the MAGRAS-stand are given. The operating conditions under which a practically-complete redeposition of the sputtered beryllium upon the target surface were experimentally-realized. A change in the microstructure of a beryllium target under sputtering and redeposition is analyzed. Some technological applications are considered. (author)

  20. Photoluminescence enhancement from GaN by beryllium doping

    Science.gov (United States)

    García-Gutiérrez, R.; Ramos-Carrazco, A.; Berman-Mendoza, D.; Hirata, G. A.; Contreras, O. E.; Barboza-Flores, M.

    2016-10-01

    High quality Be-doped (Be = 0.19 at.%) GaN powder has been grown by reacting high purity Ga diluted alloys (Be-Ga) with ultra high purity ammonia in a horizontal quartz tube reactor at 1200 °C. An initial low-temperature treatment to dissolve ammonia into the Ga melt produced GaN powders with 100% reaction efficiency. Doping was achieved by dissolving beryllium into the gallium metal. The powders synthesized by this method regularly consist of two particle size distributions: large hollow columns with lengths between 5 and 10 μm and small platelets in a range of diameters among 1 and 3 μm. The GaN:Be powders present a high quality polycrystalline profile with preferential growth on the [10 1 bar 1] plane, observed by means of X-ray diffraction. The three characteristics growth planes of the GaN crystalline phase were found by using high resolution TEM microscopy. The optical enhancing of the emission in the GaN powder is attributed to defects created with the beryllium doping. The room temperature photoluminescence emission spectra of GaN:Be powders, revealed the presence of beryllium on a shoulder peak at 3.39 eV and an unusual Y6 emission at 3.32eV related to surface donor-acceptor pairs. Also, a donor-acceptor-pair transition at 3.17 eV and a phonon replica transition at 3.1 eV were observed at low temperature (10 K). The well-known yellow luminescence band coming from defects was observed in both spectra at room and low temperature. Cathodoluminescence emission from GaN:Be powders presents two main peaks associated with an ultraviolet band emission and the yellow emission known from defects. To study the trapping levels related with the defects formed in the GaN:Be, thermoluminescence glow curves were obtained using UV and β radiation in the range of 50 and 150 °C.

  1. Failure prediction of thin beryllium sheets used in spacecraft structures

    Science.gov (United States)

    Roschke, Paul N.; Mascorro, Edward; Papados, Photios; Serna, Oscar R.

    1991-01-01

    The primary objective of this study is to develop a method for prediction of failure of thin beryllium sheets that undergo complex states of stress. Major components of the research include experimental evaluation of strength parameters for cross-rolled beryllium sheet, application of the Tsai-Wu failure criterion to plate bending problems, development of a high order failure criterion, application of the new criterion to a variety of structures, and incorporation of both failure criteria into a finite element code. A Tsai-Wu failure model for SR-200 sheet material is developed from available tensile data, experiments carried out by NASA on two circular plates, and compression and off-axis experiments performed in this study. The failure surface obtained from the resulting criterion forms an ellipsoid. By supplementing experimental data used in the the two-dimensional criterion and modifying previously suggested failure criteria, a multi-dimensional failure surface is proposed for thin beryllium structures. The new criterion for orthotropic material is represented by a failure surface in six-dimensional stress space. In order to determine coefficients of the governing equation, a number of uniaxial, biaxial, and triaxial experiments are required. Details of these experiments and a complementary ultrasonic investigation are described in detail. Finally, validity of the criterion and newly determined mechanical properties is established through experiments on structures composed of SR200 sheet material. These experiments include a plate-plug arrangement under a complex state of stress and a series of plates with an out-of-plane central point load. Both criteria have been incorporated into a general purpose finite element analysis code. Numerical simulation incrementally applied loads to a structural component that is being designed and checks each nodal point in the model for exceedance of a failure criterion. If stresses at all locations do not exceed the failure

  2. Population aging, older workers, and Canada's labour force

    OpenAIRE

    Frank T Denton; Spencer, Byron G.

    2009-01-01

    The Expert Panel on Older Workers made recommendations designed to increase the labour force participation of older workers. We explore the implications that higher rates of older-worker participation would have for the overall size and age composition of the labour force, for the productive capacity of the economy, and for the incomes of Canadians. Our purpose is to assess the potential impact that increased participation of older workers might have in offsetting any anticipated adverse effe...

  3. Modes of Occurrence and Geological Origin of Beryllium in Coals from the Pu'an Coalfield, Guizhou, Southwest China

    Institute of Scientific and Technical Information of China (English)

    YANG Jianye

    2007-01-01

    The concentration, modes of occurrence and geological origin of beryllium in five workable coal beds from the Pu'an Coalfield of Guizbou were studied using the inductively coupled-plasma mass spectrometry (ICP-MS), floating and sinking experiments (FSE) and sequential chemical extraction procedures (SCEP). The results show that the average concentration of beryllium in coals from the Pu'an Coalfield is 1.54 μg/g, much lower than that in most Chinese and worldwide coals.Beryllium in the Pu'an coals was not significantly enriched. However, it should be noted that the No. 8 coal bed from the study area has a high concentration of beryllium, 6.89 μg/g, three times higher than the background value of beryllium in coal. Beryllium in coal mainly occurs as organic association and has predominantly originated from coal-forming plants when its concentration is relatively low. The concentration of beryllium occurring as organic association is close to that distributed in inorganic matter when beryllium concentration of coal is similar to its background value, and in addition to coal-forming plants, beryllium is mainly derived from detrital materials of terrigenous origin. When beryllium is anomalously enriched in coal, it mainly occurs as organic association and is derived from volcanic tonsteins leached for a long geological time and then adsorbed by organic matter in peat mire.

  4. Thermal desorption analysis of beryllium tile pieces from JET

    International Nuclear Information System (INIS)

    Pieces of beryllium tile exposed to a D-D plasma in JET have been studied by thermal desorption spectroscopy. These tiles have a thick layer of redeposited Be-C-O with considerable hydrogen and deuterium present. The samples were heated at a constant rate of 2 C/min. from 100 C to 900 C. Desorption peaks occurred in the range of 140-480 C. There was no significant desorption at temperatures above 600 C. The amount of deuterium detected varied from a low of 8 x 1021/m2 to a high of 2.1 x 1023/m2. In one case, the amount of deuterium in a tile piece was seven times greater than the amount in a neighboring tile piece. Some of the tile pieces in the plasma-exposed region showed surface melting. Despite this, the deuterium yield from one of these pices is >1023/m2. (orig.)

  5. Thermal Induced Processes in Laminar System of Stainless Steel - Beryllium

    International Nuclear Information System (INIS)

    The paper reports on investigation of the laminar system 'stainless steel 12Cr18Ni10Ti - Be' at thermal treatment. There have been determined sequences of phase transformations along with relative amount of iron-containing phases in the samples subjected to thermal beryllization. It has been revealed that thermal beryllization of stainless steel thin foils results in γ→α transformation and formation of the beryllides NiBe and FeBe2. It has also been revealed that direct γ→α- and reverse α→γ-transformations are accompanied by, correspondingly, formation and decomposition of the beryllide NiBe. It is shown that distribution of the formed phases within sample bulk is defined by local concentration of beryllium. Based on obtained experimental data there is proposed a physical model of phase transformations in stainless steel at thermal beryllization.

  6. Nuclear charge radius measurements of radioactive beryllium isotopes

    CERN Multimedia

    2002-01-01

    We propose to measure the nuclear charge radii of the beryllium isotopes $^{7,9,10}$Be and the one-neutron halo isotope $^{11}$Be using laser spectroscopy of trapped ions. Ions produced at ISOLDE and ionized with the laser ion source will be cooled and bunched in the radio-frequency buncher of the ISOLTRAP experiment and then transferred into a specially designed Paul trap. Here, they will be cooled to temperatures in the mK range employing sympathetic and direct laser cooling. Precision laser spectroscopy of the isotope shift on the cooled ensemble in combination with accurate atomic structure calculations will provide nuclear charge radii with a precision of better than 3%. This will be the first model-independent determination of a one-neutron halo nuclear charge radius.

  7. Optical properties and structure of beryllium lead silicate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Zhidkov, I. S., E-mail: i.s.zhidkov@urfu.ru [Ural Federal University, Mira Str. 19, Yekaterinburg, 620002, Russia and Institute of Metal Physics, Russian Academy of Sciences-Ural Division, S. Kovalevskoi Str. 18, 620990 Yekaterinburg (Russian Federation); Zatsepin, A. F.; Cholakh, S. O.; Kuznetsova, Yu. A. [Ural Federal University, Mira Str. 19, Yekaterinburg, 620002 (Russian Federation)

    2014-10-21

    Luminescence and optical properties and structural features of (BeO){sub x}(PbO⋅SiO{sub 2}){sub 1−x} glasses (x = 0 ÷ 0.3) are investigated by means of optical absorption and photoluminescence spectroscopy and X-ray diffraction. The regularities of the formation of the optical absorption edge and static disorder are studied. It is shown that the optical absorption and luminescence are determined by transitions between localized states of lead ions. The impact of beryllium oxide on optical and luminescence properties and electronic structure of bands tails is discussed. The presence of two different concentration ranges with various short-range order structure and band tails nature has been established.

  8. Optical properties and structure of beryllium lead silicate glasses

    Science.gov (United States)

    Zhidkov, I. S.; Zatsepin, A. F.; Cholakh, S. O.; Kuznetsova, Yu. A.

    2014-10-01

    Luminescence and optical properties and structural features of (BeO)x(PbOṡSiO2)1-x glasses (x = 0 ÷ 0.3) are investigated by means of optical absorption and photoluminescence spectroscopy and X-ray diffraction. The regularities of the formation of the optical absorption edge and static disorder are studied. It is shown that the optical absorption and luminescence are determined by transitions between localized states of lead ions. The impact of beryllium oxide on optical and luminescence properties and electronic structure of bands tails is discussed. The presence of two different concentration ranges with various short-range order structure and band tails nature has been established.

  9. Specification for nuclear-grade beryllium oxide powder

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2008-01-01

    1.1 This specification defines the physical and chemical requirements of nuclear-grade beryllium oxide (BeO) powder to be used in fabricating nuclear components. 1.2 This specification does not include requirements for health and safety. , , It recognizes the material as a Class B poison and suggests that producers and users become thoroughly familiar with and comply to applicable federal, state, and local regulations and handling guidelines. 1.3 Special tests and procedures are given in Annex A1 and Annex A2. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

  10. Stress distribution and fracture behavior of beryllium compact tension specimens

    International Nuclear Information System (INIS)

    Compact tension specimens of beryllium (Be) were designed to study fracture behavior and mechanical properties. The local stress distribution near a notch in a compact tension specimen was measured in situ by the combination of an X-ray stress analysis and a custom-designed load device. The fracture morphology was observed by scanning electron microscopy. The result showed that the local stresses near the notch tip are much higher than in other areas, and cracking occurs first in that area. The load-crack opening displacement curve of the Be compact tension specimen was obtained, and used to calculate the fracture toughness as 15.7 MPa√m. The compact tension specimen fracture surfaces were mainly characterized by cleavage fracture over three different areas. Cleavage micro-cracks along the basal slip plane were formed at the crack tip, and their growth was controlled by the primary stress after reaching a critical length

  11. Modelling of radiation impact on ITER Beryllium wall

    International Nuclear Information System (INIS)

    In the ITER H-Mode confinement regime, edge localized instabilities (ELMs) will perturb the discharge. Plasma lost after each ELM moves along magnetic field lines and impacts on divertor armour, causing plasma contamination by back propagating eroded carbon or tungsten. These impurities produce enhanced radiation flux distributed mainly over the beryllium main chamber wall. The simulation of the complicated processes involved are subject of the integrated tokamak code TOKES that is currently under development. This work describes the new TOKES model for radiation transport through confined plasma. Equations for level populations of the multi-fluid plasma species and the propagation of different kinds of radiation (resonance, recombination and bremsstrahlung photons) are implemented. First simulation results without account of resonance lines are presented.

  12. Electron microscope observation of single - crystalline beryllium thin foils

    International Nuclear Information System (INIS)

    Thin foils prepared from single crystalline beryllium simples deformed at room temperature, have been observed by transmission electron microscopy. The various deformation modes have been investigated separately, from their early stages and their characteristic dislocation configurations have been observed. Basal slip is characterized at is outset by the presence of numerous dipoles and elongated prismatic loops. More pronounced cold work leads to the formation of dislocation tangles and bundles which eventually give a cellular structure. Prismatic slip begins by the cross-slip of dislocations from the basal plane into the prismatic plane. A cellular structure is equally observed in heavily deformed samples. Sessile dislocations have been observed in twin boundaries; they are produced by reactions between slip dislocations and twin dislocations. Finally, the study of samples quenched from 1100 deg. C and annealed at 200 deg. C has shown that the observed loops lie in prismatic planes and have a Burgers vector b 1/3. (authors)

  13. Electromagnetic properties of the Beryllium-11 nucleus in Halo EFT

    Directory of Open Access Journals (Sweden)

    Hammer H.-W.

    2010-04-01

    Full Text Available We compute electromagnetic properties of the Beryllium-11 nucleus using an effective field theory that exploits the separation of scales in this halo system. We fix the parameters of the EFT from measured data on levels and scattering lengths in the 10Be plus neutron system. We then obtain predictions for the B(E1 strength of the 1/2+ to 1/2− transition in the 11Be nucleus. We also compute the charge radius of the ground state of 11Be. Agreement with experiment within the expected accuracy of a leading-order computation in this EFT is obtained. We also indicate how higher-order corrections that affect both s-wave and p-wave 10 Be-neutron interactions will affect our results.

  14. Tensile and fracture toughness test results of neutron irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Chaouadi, R.; Moons, F.; Puzzolante, J.L. [Centre d`Etude de l`Energie Nucleaire, Mol (Belgium)

    1998-01-01

    Tensile and fracture toughness test results of four Beryllium grades are reported here. The flow and fracture properties are investigated by using small size tensile and round compact tension specimens. Irradiation was performed at the BR2 material testing reactor which allows various temperature and irradiation conditions. The fast neutron fluence (>1 MeV) ranges between 0.65 and 2.45 10{sup 21} n/cm{sup 2}. In the meantime, un-irradiated specimens were aged at the irradiation temperatures to separate if any the effect of temperature from irradiation damage. Test results are analyzed and discussed, in particular in terms of the effects of material grade, test temperature, thermal ageing and neutron irradiation. (author)

  15. First beryllium capsule implosions on the National Ignition Facility

    Science.gov (United States)

    Kline, J. L.; Yi, S. A.; Simakov, A. N.; Olson, R. E.; Wilson, D. C.; Kyrala, G. A.; Perry, T. S.; Batha, S. H.; Zylstra, A. B.; Dewald, E. L.; Tommasini, R.; Ralph, J. E.; Strozzi, D. J.; MacPhee, A. G.; Callahan, D. A.; Hinkel, D. E.; Hurricane, O. A.; Milovich, J. L.; Rygg, J. R.; Khan, S. F.; Haan, S. W.; Celliers, P. M.; Clark, D. S.; Hammel, B. A.; Kozioziemski, B.; Schneider, M. B.; Marinak, M. M.; Rinderknecht, H. G.; Robey, H. F.; Salmonson, J. D.; Patel, P. K.; Ma, T.; Edwards, M. J.; Stadermann, M.; Baxamusa, S.; Alford, C.; Wang, M.; Nikroo, A.; Rice, N.; Hoover, D.; Youngblood, K. P.; Xu, H.; Huang, H.; Sio, H.

    2016-05-01

    The first indirect drive implosion experiments using Beryllium (Be) capsules at the National Ignition Facility confirm the superior ablation properties and elucidate possible Be-ablator issues such as hohlraum filling by ablator material. Since the 1990s, Be has been the preferred Inertial Confinement Fusion (ICF) ablator because of its higher mass ablation rate compared to that of carbon-based ablators. This enables ICF target designs with higher implosion velocities at lower radiation temperatures and improved hydrodynamic stability through greater ablative stabilization. Recent experiments to demonstrate the viability of Be ablator target designs measured the backscattered laser energy, capsule implosion velocity, core implosion shape from self-emission, and in-flight capsule shape from backlit imaging. The laser backscatter is similar to that from comparable plastic (CH) targets under the same hohlraum conditions. Implosion velocity measurements from backlit streaked radiography show that laser energy coupling to the hohlraum wall is comparable to plastic ablators. The measured implosion shape indicates no significant reduction of laser energy from the inner laser cone beams reaching the hohlraum wall as compared with plastic and high-density carbon ablators. These results indicate that the high mass ablation rate for beryllium capsules does not significantly alter hohlraum energetics. In addition, these data, together with data for low fill-density hohlraum performance, indicate that laser power multipliers, required to reconcile simulations with experimental observations, are likely due to our limited understanding of the hohlraum rather than the capsule physics since similar multipliers are needed for both Be and CH capsules as seen in experiments.

  16. Cost effective aluminum beryllium mirrors for critical optics applications

    Science.gov (United States)

    Say, Carissa; Duich, Jack; Huskamp, Chris; White, Ray

    2013-09-01

    The unique performance of aluminum-beryllium frequently makes it an ideal material for manufacturing precision optical-grade metal mirrors. Traditional methods of manufacture utilize hot-pressed powder block in billet form which is subsequently machined to final dimensions. Complex component geometries such as lightweighted, non-plano mirrors require extensive tool path programming, fixturing, and CNC machining time and result in a high buy-to-fly ratio (the ratio of the mass of raw material purchased to the mass of the finished part). This increases the cost of the mirror structure as a significant percentage of the procurement cost is consumed in the form of machining, tooling, and scrap material that do not add value to the final part. Inrad Optics, Inc. and IBC Advanced Alloys Corp. undertook a joint study to evaluate the suitability of investment-cast Beralcast® 191 and 363 aluminum-beryllium as a precision mirror substrate material. Net shape investment castings of the desired geometry minimizes machining to just cleanup stock, thereby reducing the recurring procurement cost while still maintaining performance. The thermal stability of two mirrors, (one each of Beralcast® 191 and Beralcast® 363), was characterized from -40°F to +150°F. A representative pocketed mirror was developed, including the creation of a relevant geometry and production of a cast component to validate the approach. Information from the demonstration unit was used as a basis for a comparative cost study of the representative mirror produced in Beralcast® and one machined from a billet of AlBeMet® 162 (AlBeMet® is a registered trademark of Materion Corporation). The technical and financial results of these studies will be discussed in detail.

  17. REMOVAL OF BERYLLIUM FROM DRINKING WATER BY CHEMICAL COAGULATION AND LIME SOFTENING

    Science.gov (United States)

    The effectiveness of conventional drinking water treatment and lime softening was evaluated for beryllium removal from two drinking water sources. ar test studies were conducted to determine how common coagulants (aluminum sulfate and ferric chloride and lime softening performed ...

  18. Analysis of beryllium and depleted uranium: An overview of detection methods in aerosols and soils

    International Nuclear Information System (INIS)

    We conducted a survey of commercially available methods for analysis of beryllium and depleted uranium in aerosols and soils to find a reliable, cost-effective, and sufficiently precise method for researchers involved in environmental testing at the Yuma Proving Ground, Yuma, Arizona. Criteria used for evaluation include cost, method of analysis, specificity, sensitivity, reproducibility, applicability, and commercial availability. We found that atomic absorption spectrometry with graphite furnace meets these criteria for testing samples for beryllium. We found that this method can also be used to test samples for depleted uranium. However, atomic absorption with graphite furnace is not as sensitive a measurement method for depleted uranium as it is for beryllium, so we recommend that quality control of depleted uranium analysis be maintained by testing 10 of every 1000 samples by neutron activation analysis. We also evaluated 45 companies and institutions that provide analyses of beryllium and depleted uranium. 5 refs., 1 tab

  19. Analysis of beryllium and depleted uranium: An overview of detection methods in aerosols and soils

    Energy Technology Data Exchange (ETDEWEB)

    Camins, I.; Shinn, J.H.

    1988-06-01

    We conducted a survey of commercially available methods for analysis of beryllium and depleted uranium in aerosols and soils to find a reliable, cost-effective, and sufficiently precise method for researchers involved in environmental testing at the Yuma Proving Ground, Yuma, Arizona. Criteria used for evaluation include cost, method of analysis, specificity, sensitivity, reproducibility, applicability, and commercial availability. We found that atomic absorption spectrometry with graphite furnace meets these criteria for testing samples for beryllium. We found that this method can also be used to test samples for depleted uranium. However, atomic absorption with graphite furnace is not as sensitive a measurement method for depleted uranium as it is for beryllium, so we recommend that quality control of depleted uranium analysis be maintained by testing 10 of every 1000 samples by neutron activation analysis. We also evaluated 45 companies and institutions that provide analyses of beryllium and depleted uranium. 5 refs., 1 tab.

  20. Estimations of neutron yield from beryllium target irradiated by SPring-8 hard synchrotron radiation

    CERN Document Server

    Gryaznykh, D A; Plokhoi, V V

    2000-01-01

    The possibility of creating a neutron source based on ''SPring-8'' synchrotron radiation interaction with beryllium targets is discussed. The possible neutron yield is estimated to be of order 10 sup 1 sup 2 s sup - sup 1 .

  1. Off the Beaten Track-A Hitchhiker's Guide to Beryllium Chemistry.

    Science.gov (United States)

    Naglav, Dominik; Buchner, Magnus R; Bendt, Georg; Kraus, Florian; Schulz, Stephan

    2016-08-26

    This Minireview aims to give an introduction to beryllium chemistry for all less-experienced scientists in this field of research. Up to date information on the toxicity of beryllium and its compounds are reviewed and several basic and necessary guidelines for a safe and proper handling in modern chemical research laboratories are presented. Interesting phenomenological observations are described that are related directly to the uniqueness of this element, which are also put into historical context. Herein we combine the contributions and experiences of many scientist that work passionately in this field. We want to encourage fellow scientists to reconcile the long-standing reservations about beryllium and its compounds and motivate intense research on this spurned element. Who on earth should be able to deal with beryllium and its compounds if not chemists? PMID:27364901

  2. Views of the workers

    International Nuclear Information System (INIS)

    This paper is written from the perspective of the worker. As such it presents the workers' viewpoint with respect to the present status and problems to be solved with regard to occupational exposure. (author)

  3. Coal worker's pneumoconiosis

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/000130.htm Coal worker's pneumoconiosis To use the sharing features on this page, please enable JavaScript. Coal worker's pneumoconiosis is a lung disease that results ...

  4. Characterization of phagolysosomal simulant fluid for study of beryllium aerosol particle dissolution.

    Science.gov (United States)

    Stefaniak, A B; Guilmette, R A; Day, G A; Hoover, M D; Breysse, P N; Scripsick, R C

    2005-02-01

    A simulant of phagolysosomal fluid is needed for beryllium particle dissolution research because intraphagolysosomal dissolution is believed to be a necessary step in the cellular immune response associated with development of chronic beryllium disease. Thus, we refined and characterized a potassium hydrogen phthalate (KHP) buffered solution with pH 4.55, termed phagolysosomal simulant fluid (PSF), for use in a static dissolution technique. To characterize the simulant, beryllium dissolution in PSF was compared to dissolution in the J774A.1 murine cell line. The effects of ionic composition, buffer strength, and the presence of the antifungal agent alkylbenzyldimethylammonium chloride (ABDC) on beryllium dissolution in PSF were evaluated. Beryllium dissolution in PSF was not different from dissolution in the J774A.1 murine cell line (p = 0.78) or from dissolution in another simulant having the same pH but different ionic composition (p = 0.73). A buffer concentration of 0.01-M KHP did not appear adequate to maintain pH under all conditions. There was no difference between dissolution in PSF with 0.01-M KHP and 0.02-M KHP (p = 0.12). At 0.04-M KHP, beryllium dissolution was increased relative to 0.02-M KHP (p = 0.02). Use of a 0.02-M KHP buffer concentration in the standard formulation for PSF provided stability in pH without alteration of the dissolution rate. The presence of ABDC did not influence beryllium dissolution in PSF (p = 0.35). PSF appears to be a useful and appropriate model of in vitro beryllium dissolution when using a static dissolution technique. In addition, the critical approach used to evaluate and adjust the composition of PSF may serve as a framework for characterizing PSF to study dissolution of other metal and oxide particles.

  5. Impact of beryllium reflector ageing on Safari–1 reactor core parameters / L.E. Moloko

    OpenAIRE

    Moloko, Lesego Ernest

    2011-01-01

    The build–up of 6Li and 3He, that is, the strong thermal neutron absorbers or the so called "neutron poisons", in the beryllium reflector changes the physical characteristics of the reactor, such as reactivity, neutron spectra, neutron flux level, power distribution, etc.; furthermore,gaseous isotopes such as 3H and 4He induce swelling and embrittlement of the reflector. The SAFARI–1 research reactor, operated by Necsa at Pelindaba in South Africa, uses a beryllium reflector on...

  6. The Status of Beryllium Research for Fusion in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Glen R. Longhurst

    2003-12-01

    Use of beryllium in fusion reactors has been considered for neutron multiplication in breeding blankets and as an oxygen getter for plasma-facing surfaces. Previous beryllium research for fusion in the United States included issues of interest to fission (swelling and changes in mechanical and thermal properties) as well as interactions with plasmas and hydrogen isotopes and methods of fabrication. When the United States formally withdrew its participation in the International Thermonuclear Experimental Reactor (ITER) program, much of this effort was terminated. The focus in the U.S. has been mainly on toxic effects of beryllium and on industrial hygiene and health-related issues. Work continued at the INEEL and elsewhere on beryllium-containing molten salts. This activity is part of the JUPITER II Agreement. Plasma spray of ITER first wall samples at Los Alamos National Laboratory has been performed under the European Fusion Development Agreement. Effects of irradiation on beryllium structure are being studied at Oak Ridge National Laboratory. Numerical and phenomenological models are being developed and applied to better understand important processes and to assist with design. Presently, studies are underway at the University of California Los Angeles to investigate thermo-mechanical characteristics of beryllium pebble beds, similar to research being carried out at Forschungszentrum Karlsruhe and elsewhere. Additional work, not funded by the fusion program, has dealt with issues of disposal, and recycling.

  7. Sensitive detection of beryllium using a fiber optic liquid waveguide cell.

    Science.gov (United States)

    Deng, Gang; Wei, Lily; Collins, Greg E

    2003-05-28

    The metallochromic chelating agent, Chromazurol S, has been utilized in conjunction with a fiber optic liquid waveguide capillary cell to enable the sensitive detection of beryllium in solution (30 ng l(-1) detection limit) and following extraction from a contaminated plexiglas surface (0.5 ng cm(-2) detection limit). The addition of a cationic surfactant, cetylpyridinium chloride, to Chromazurol S at pH 10 in Tris-HCl buffer results in the formation of two bathochromic peaks in the visible spectrum following metal chelation by beryllium. The first absorbance band, at 515 nm, is intermediate in nature, permitting maximal sensitivity for low beryllium concentrations, but diminishing in intensity at concentrations above 100 mug l(-1). The second absorbance band, centered at 610 nm, dominates for beryllium concentrations of 100 mug l(-1) and above. Experimental conditions including pH, buffer type, additive surfactants, masking agents, and dye concentration were investigated in order to optimize detection sensitivity and selectivity. A fiber optic spectrometer is used with both a liquid waveguide capillary cell and 1 cm cuvette cell, to give a sensitive and broad dynamic range for beryllium detection that capitalizes on both beryllium metal chelate absorbance bands formed under these conditions.

  8. Preconcentration and separation of ultra-trace beryllium using quinalizarine-modified magnetic microparticles

    Energy Technology Data Exchange (ETDEWEB)

    Ashtari, Parviz, E-mail: pashtari@aeoi.org.ir [State Key Laboratory of Chemo/Biosensing and Chemometrics, Biomedical Engineering Center, College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082 (China); NFCS, Nuclear Science and Technology Research Institute, PO Box 11365-8486, Tehran (Iran, Islamic Republic of); Wang Kemin; Yang Xiaohai [State Key Laboratory of Chemo/Biosensing and Chemometrics, Biomedical Engineering Center, College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082 (China); Ahmadi, Seyed Javad [NFCS, Nuclear Science and Technology Research Institute, PO Box 11365-8486, Tehran (Iran, Islamic Republic of)

    2009-07-30

    Magnetically-assisted chemical separation/preconcentration method for the analysis of beryllium from aqueous solutions was developed. According to this method several extractants were coated on certain magnetic microparticles to assist the extraction of beryllium from the aqueous solutions. The influence of different parameters (type and amount of extractant, pH, equilibrium time and ionic strength) was investigated. Also, the interfering effect of various cationic and anionic species on the percent recovery of beryllium was studied. The applied spectrophotometric method showed good linearity and precision at a given wavelength (605.0 nm). Among the extractants used, quinalizarine resulted in almost a full recovery of beryllium at pH 7.4, which was the optimum extraction pH. The equilibrium time of the extraction was 10.0 min. The quantitative re-extraction was carried out by 0.5 M nitric acid. Also, the stability of the extractant-coated magnetic microparticles was 4 cycles (extraction and re-extraction) and the used magnetic microparticles showed good selectivity for beryllium against other cations and anions. Finally, the developed method was applicable for the preconcentration and separation of beryllium from spring water, tap water and certified reference waters. The obtained detection limit was 30 ng L{sup -1}.

  9. Characterization of beryllium deformation using in-situ x-ray diffraction

    Energy Technology Data Exchange (ETDEWEB)

    Magnuson, Eric Alan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Brown, Donald William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Clausen, Bjorn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Sisneros, Thomas A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Park, Jun-Sang [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-08-24

    Beryllium’s unique mechanical properties are extremely important in a number of high performance applications. Consequently, accurate models for the mechanical behavior of beryllium are required. However, current models are not sufficiently microstructure aware to accurately predict the performance of beryllium under a range of processing and loading conditions. Previous experiments conducted using the SMARTS and HIPPO instruments at the Lujan Center(LANL), have studied the relationship between strain rate and texture development, but due to the limitations of neutron diffraction studies, it was not possible to measure the response of the material in real-time. In-situ diffraction experiments conducted at the Advanced Photon Source have allowed the real time measurement of the mechanical response of compressed beryllium. Samples of pre-strained beryllium were reloaded orthogonal to their original load path to show the reorientation of already twinned grains. Additionally, the in-situ experiments allowed the real time tracking of twin evolution in beryllium strained at high rates. The data gathered during these experiments will be used in the development and validation of a new, microstructure aware model of the constitutive behavior of beryllium.

  10. Investigation of the mechanism of interaction of Lithium 6 ions on Beryllium 9

    International Nuclear Information System (INIS)

    The objective of this research on the interaction of Lithium 6 and Beryllium 9 ions is to obtain new indications on the mode of interaction of these heavy ions, and on the configuration of target nuclei and projectile nuclei. In a first part, the author presents and describes the experimental conditions which comprise a Van de Graaff accelerator, a source, a stripper, and a target. He reports the study of α particles emitted by the reaction between the Lithium and Beryllium ions: description of the experimental installation (irradiation chamber and method), presentation and interpretation of experimental results. In the next part, he reports the study of Lithium 7 and Beryllium 10 nuclides emitted by disintegration of Beryllium 11: description of experimental conditions, variations of cross sections, variation of the cross section rate, and interpretation. The author then addresses the study of the intervention of the mode of interaction by 15N compound nucleus in the reactions between lithium and beryllium ions: study of intensities of the different spectrum lines, measurement of the Doppler effect produced of the 479 keV line, interpretation of results. In conclusion, the author analyses the mechanism of interaction between lithium and beryllium ions, and discusses different theories: the Newns and Glendenning theories, and the Leigh theory

  11. Assessment of psychosocial risk factors for the development of non-specific chronic disabling low back pain in Japanese workers-findings from the Japan Epidemiological Research of Occupation-related Back Pain (JOB) study.

    Science.gov (United States)

    Matsudaira, Ko; Kawaguchi, Mika; Isomura, Tatsuya; Inuzuka, Kyoko; Koga, Tadashi; Miyoshi, Kota; Konishi, Hiroaki

    2015-01-01

    To investigate the associations between psychosocial factors and the development of chronic disabling low back pain (LBP) in Japanese workers. A 1 yr prospective cohort of the Japan Epidemiological Research of Occupation-related Back Pain (JOB) study was used. The participants were office workers, nurses, sales/marketing personnel, and manufacturing engineers. Self-administered questionnaires were distributed twice: at baseline and 1 yr after baseline. The outcome of interest was the development of chronic disabling LBP during the 1 yr follow-up period. Incidence was calculated for the participants who experienced disabling LBP during the month prior to baseline. Logistic regression was used to assess risk factors for chronic disabling LBP. Of 5,310 participants responding at baseline (response rate: 86.5%), 3,811 completed the questionnaire at follow-up. Among 171 eligible participants who experienced disabling back pain during the month prior to baseline, 29 (17.0%) developed chronic disabling LBP during the follow-up period. Multivariate logistic regression analysis implied reward to work (not feeling rewarded, OR: 3.62, 95%CI: 1.17-11.19), anxiety (anxious, OR: 2.89, 95%CI: 0.97-8.57), and daily-life satisfaction (not satisfied, ORs: 4.14, 95%CI: 1.18-14.58) were significant. Psychosocial factors are key to the development of chronic disabling LBP in Japanese workers. Psychosocial interventions may reduce the impact of LBP in the workplace. PMID:26051289

  12. Tritium release of Li4SiO4, Li2O and beryllium and chemical compatibility of beryllium with Li4SiO4, Li2O and steel (SIBELIUS irradiation)

    International Nuclear Information System (INIS)

    The objective of the SIBELIUS irradiation, a joint EC-US project performed at CEN Grenoble, was to investigate the oxidation kinetics of beryllium in contact with ceramic and the nature and extent of beryllium in contact with ceramic and the nature and extent of beryllium interaction with (316 L and 1.4914) steel in a neutron environment. In this work post irradiation examinations of SIBELIUS specimens performed at KfK are described. Tritium release of Li4SiO4, Li2O and beryllium was studied by out-of-pile annealing and chemical compatibility of beryllium with Li4SiO4, Li2O and steel by microscopic examinations. Tritium release of the ceramics was found to be consistent with SIBELIUS inpile observations and previous tests. Release of tritium generated in beryllium was found to be very slow, in accordance with previous work. For beryllium which was in contact with ceramic during irradiation, a second type of tritium, caused by injection of 2.7 MeV tritons generated in the ceramic, is observed. Release of injected tritium is faster than that of generated. Evidence for injected tritium in beryllium was also found in the microscopic studies. The observed minor chemical reactions of beryllium with steel and probably also those with breeder materials under neutron irradiation are consistent with the results of laboratory annealing tests. (orig.)

  13. Assessment of life quality of workers in an indium smeltery%某铟冶炼厂作业工人生命质量评价

    Institute of Scientific and Technical Information of China (English)

    黄世文; 江世强; 梁启荣; 黄才千; 陈雪冬

    2013-01-01

    目的 了解某大型铟冶炼厂作业工人的生命质量,为预防和控制铟冶炼接触人群健康危害提供依据.方法 对某铟冶炼厂作业场所空气中职业病危害因素进行调查、检测,按国家职业卫生标准进行评价;采用健康调查量表(SF-36)对208名铟冶炼厂作业工人(观察组)和243名铟冶炼厂辅助工种工人(对照组)进行问卷调查并分析.结果 铟冶炼过程中存在粉尘、铅、砷、镉、铟、砷化氢、各种酸碱、噪声、高温等职业病危害因素,其中砷化氢浓度超过国家职业卫生标准.两组调查人群躯体功能和社会角色功能分值接近;观察组躯体疼痛、总体健康、生命活力分值低于对照组,差异有统计学意义(P<0.05).在心理健康方面,两组心理功能对角色的影响比较,差异无统计学意义(P>0.05);观察组的心理健康分值低于对照组,差异有统计学意义(P<0.05).男女之间躯体功能对角色的影响、躯体疼痛、总体健康、社会角色功能等比较,差异有统计学意义(P<0.05),女性分值均低于男性.结论 某铟冶炼厂主要作业场所存在粉尘、化学、物理等职业病危害因素;与对照组比较,铟冶炼厂职业接触人群的生命质量较低,多处于亚健康状态.铟冶炼厂作业工人职业接触引起的职业危害必须引起重视.%Objective To investigate workers' life quality in an indium smeltery and to provide scientific criteria for preventing and controlling occupational hazards of exposed population. Methods Occupational health survey in an indium smeltery was conducted and occupational hazards were detected in workplaces. Results were evaluated according to national occupational health standards. Moreover, life quality of 208 indium smelters(observation group) and 243 indium smelting auxiliary workers(control group) was assessed with SF-36 scale. Results Occupational hazards in the indium smelting process included dust, lead

  14. Characteristics of microstructure and tritium release properties of different kinds of beryllium pebbles for application in tritium breeding modules

    Energy Technology Data Exchange (ETDEWEB)

    Kurinskiy, P.; Vladimirov, P.; Moeslang, A. [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany). Inst. for Applied Materials - Applied Materials Physics (IAM-AWP); Rolli, R. [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany). Inst. for Applied Materials - Materials Biomechanics (IAM-WBM); Zmitko, M. [The European Joint Undertaking for ITER and the Development of Fusion Energy, Barcelona (Spain)

    2013-07-01

    Beryllium pebbles with diameters of 1 mm are considered to be perspective material for the use as neutron multiplier in tritium breeding modules of fusion reactors. Up to now, the main concept of helium-cooled breeding blanket in ITER project foresees the use of 1 mm beryllium pebbles fabricated by company NGK, Japan. It is notable that beryllium pebbles of other types are commercially available at the market. Presented work is dedicated to a study of characteristics of microstructure, packaging density and parameters of tritium release of beryllium pebbles produced by Bochvar Institute, Russian Federation, and Company Materion, USA. (orig.).

  15. Immune Functions of the Garment Workers

    Directory of Open Access Journals (Sweden)

    LN Islam

    2012-09-01

    Full Text Available Background: Occupational exposure to cotton dust, fibers, metal fumes and different chemicals used in the apparel manufacturing industries cause a wide range of physical and psychological health problems in the garment workers that may also affect their immune function.Objective: To assess the immune system function in garment workers.Methods: A total of 45 workers of a garment factory, and 41 control subjects, not exposed to the garment working environment were enrolled in this study. In the study subjects, the complement system function was assessed as bactericidal activity on Escherichia coli DH5α cells using the standard plate count method. Serum complement components C3 and C4 were measured by immunoprecipitation, and IgG was measured by immunonephelometry.Results: The bactericidal activity of serum complement in the garment workers (range: 93.5%–99.9% was significantly (p<0.01 lower than that in the controls (range: 98.6%–100%. The heat-inactivated serum of the workers showed a significantly enhanced bactericidal activity. In the garment workers, the mean levels of complement C3, and C4 were 1.75 and 0.26 g/L, respectively that were close to those of the controls. The mean IgG level in the garment workers was 13.5 g/L that was significantly (p<0.001 higher than that in the controls. Conclusion: Working in a garment factory may affect the immune system.

  16. [Workplace accomodations for two workers with narcolepsy].

    Science.gov (United States)

    Vico Garcerán, Belén; Monzó Salas, Monserrat; Cuenca Esteve, Francisco; Luis Domingo, José

    2013-01-01

    We describe the case of two workers evaluated in our occupational health unit. The first worker was a kitchen aide; the second was a primary care physician. Both had been diagnosed with narcolepsy and had obvious disability.We assessed occupational hazards related to their jobs, analysed their tasks, and performed medical examinations. Afterwards, we offered recommendations to the patients, consisting of avoidance of situations involving a risk of work accidents and improving their sleep habits. Narcolepsy is a rare disorder, but it has important social and occupational consequences. A better understanding of the disease and some work accommodations can help improve the quality of life of affected workers. PMID:23700708

  17. Medical standards for radiation workers

    International Nuclear Information System (INIS)

    The Council of the European Communities in its Directive of June 1, 1976 has laid down revised basic safety standards for the health protection of the general public and workers against the danger of ionising radiation. The Directive requires each Member State of the Community 'for the guidance of medical practitioners.....to draw up a list, which need not be exhaustive, of the criteria which should be taken into account when judging a worker's fitness to be exposed to ionising radiation'. Medical officers with current responsibility for radiation workers in the U.K. therefore met recently for informal exploratory discussion at the National Radiological Protection Board's headquarters, and an account is given of the views expressed there about the composition of the required 'list', and the possibility of standardizing the procedure adopted. Consideration was given to the objectives of medical examinations, the form of examination, and specific conditions which may give rise to difficulty in making a fitness assessment. These conditions are skin abnormalities, blood abnormalities, cataract, pregnancy, and psychological and psychiatric conditions. It was concluded that the medical examination of radiation workers, including blood examinations, are of value to the extent that they form part of any good general occupational health practice. The promulgation of the Euratom Directive has provided an opportunity for reviewing and standardising procedures for medical surveillance in the light of current knowledge concerning average occupational radiation doses and dose-response relationships. (U.K.)

  18. In-pile thermocycling testing and post-test analysis of beryllium divertor mockups

    Energy Technology Data Exchange (ETDEWEB)

    Giniatulin, R.; Mazul, I. [Efremov Inst., St. Petersburg (Russian Federation); Melder, R.; Pokrovsky, A.; Sandakov, V.; Shiuchkin, A.

    1998-01-01

    The main damaging factors which impact the ITER divertor components are neutron irradiation, cyclic surface heat loads and hydrogen environment. One of the important questions in divertor mockups development is the reliability of beryllium/copper joints and the beryllium resistance under neutron irradiation and thermal cycling. This work presents the experiment, where neutron irradiation and thermocyclic heat loads were applied simultaneously for two beryllium/copper divertor mockups in a nuclear reactor channel to simulate divertor operational conditions. Two mockups with different beryllium grades were mounted facing each other with the tantalum heater placed between them. This device was installed in the active zone of the nuclear reactor SM-2 (Dimitrovgrad, Russia) and the tantalum block was heated by neutron irradiation up to a high temperature. The main part of the heat flux from the tantalum surface was transported to the beryllium surface through hydrogen, as a result the heat flux loaded two mockups simultaneously. The mockups were cooled by reactor water. The device was lowered to the active zone so as to obtain the heating regime and to provide cooling lifted. This experiment was performed under the following conditions: tantalum heater temperature - 1950degC; hydrogen environment -1000 Pa; surface heat flux density -3.2 MW/m{sup 2}; number of thermal cycles (lowering and lifting) -101; load time in each cycle - 200-5000 s; dwell time (no heat flux, no neutrons) - 300-2000 s; cooling water parameters: v - 1 m/s, Tin - 50degC, Pin - 5 MPa; neutron fluence -2.5 x 10{sup 20} cm{sup -2} ({approx}8 years of ITER divertor operation from the start up). The metallographic analysis was performed after experiment to investigate the beryllium and beryllium/copper joint structures, the results are presented in the paper. (author)

  19. Knowledge and skills of primary health care workers trained on integrated management of neonatal and childhood illness: Follow-up assessment 3 years after the training

    Directory of Open Access Journals (Sweden)

    J Venkatachalam

    2011-01-01

    Full Text Available Background: The primary health care workers of a district in northern India were trained in the year 2006 for Integrated Management of Neonatal and Childhood Illness (IMNCI using two different training methods: conventional 8-day training and new interrupted 5-day training. Knowledge and skills may decline over a period of time. Rate of decline may be associated with the type of training. A study was thus conducted to see the retention of knowledge and skills in the two training groups, 3 years after the initial training. Materials and Methods: This study was done in the Panchkula district of Haryana state in northern India. In the year 2006, 50 primary health care workers were given new interrupted 5-day training and another 35 workers were given conventional 8-day training on IMNCI. Knowledge and skills of the same workers were evaluated in the year 2009, using the same methodology and tools as were used in the year 2006. Data analysis was done to see the extent of decline in knowledge and skills in these 3 years and whether decline was more in any particular training group. Results: Compared to post-training score in the year 2006, composite knowledge and skill scores for Auxilliary Nurse Midwives (ANMs and Anganwari workers (AWWs together declined significantly in the year 2009 from 74.6 to 58.0 in 8-day training group and from 73.2 to 57.0 in 5-day training group (P < 0.001. Follow-up composite scores in the two training groups were similar. Whereas the decline was more for knowledge scores in 8-day training group and for skill score in 5-day training group, the pattern of decline was inconsistent for different health conditions and among ANMs and AWWs. Conclusion: Long-term retention of knowledge and skills in 5-day group was equivalent to that in 8-day training group. Refresher trainings may boost up the decline in the knowledge and skills.

  20. Sub-micro level monitoring of beryllium ions with a novel beryllium sensor based on 2,6-diphenyl-4-benzo-9-crown-3-pyridine.

    Science.gov (United States)

    Ganjali, Mohammad Reza; Rahimi-Nasrabadi, Mehdi; Maddah, Bozorgmehr; Moghimi, Abolghasem; Faal-Rastegar, Madjid; Borhany, Shahin; Namazian, Mansour

    2004-07-01

    The 2,6-diphenyl-4-benzo-9-crown-3-pyridine (DPCP) was used as an excellent ionophore in construction of a coated graphite poly(vinyl chloride) (PVC)-based membrane sensor. The best performance was obtained with a membrane composition of 30% poly(vinyl chloride), 60% o-nitrophenyloctyl ether (NPOE), 5% 2,6-diphenyl-4-benzo-9-crown-3-pyridine and 5% sodium tetraphenyl borate (TBP). This sensor shows very good selectivity and sensitivity towards beryllium ion over a wide variety of cations, including alkali, alkaline earth, transition and heavy metal ions. The sensor revealed a great enhancement in selectivity coefficients and sensitivity for beryllium, in comparison with the previously reported beryllium electrodes. The electrode exhibits a Nernstian behavior (with slope of 29.6mV per decade) over a very wide concentration range (1.0x10(-7) to 1.0x10(-1)) with a detection limit of 4.0x10(-8)M (360pgml(-1)). It shows relatively fast response time, in whole concentration range (beryllium in mineral ore.

  1. Study on assessment technology of safety psychology for construction workers by fuzzy mathematics%基于模糊数学的建筑工人安全心理评估技术研究

    Institute of Scientific and Technical Information of China (English)

    刘浩燃; 陈绍清; 刘光才; 冉光建

    2013-01-01

    In view of assessment on safety psychology of construction workers,it can effectively prevent and reduce construction accidents.Combining with previous results and expert opinion,an evaluation system on safety psychologly construction workers,including 18 indexes,was proposed through the analysis on the characteristics of the construction work and major psychological and physiological activities of the job,the interviews on the workers who serving a construction in site in Chongqing,the survey and results analysis on the questionnaire Ⅰ by software of SPSS V19.0.Delphi was used to calculate the relative weights of the 18 indexes.With the establishment of evaluation criterion based on human intelligence distribution,the fuzzy comprehensive evaluation model was established.The safety status of construction worker was figured out according to the principle of the biggest subject.Through the example of calculation with the Questionnaire Ⅱ measured by 18 indexes,this model can objectively evaluate the psychological state of construction worker.This model enables the assessment on the safety psychology of construction workers to achieve a quantitative study and plays a guiding role in construction workers safety psychological evaluation.%对建筑工人安全心理评估,可以有效预防和减少建筑施工事故的发生.通过分析建筑施工工作特征以及作业中主要的心理生理活动,对重庆市某建筑工地的建筑工人访谈,问卷Ⅰ调查及结果SPSS V19.0软件分析,结合前人成果和专家意见,得到由18个指标组成的建筑工人安全心理评估体系.用Delphi法对18个指标的权重赋值,根据人类智力分布等建立评判标准,构建了模糊综合评价数学模型.根据最大隶属度原则,得出安全心理综合评价等级.通过由18个指标形成的问卷Ⅱ实测表明,此模型可以客观评估建筑工人的心理状态,使建筑工人安全心理评估实现了定量化,对建筑

  2. Respiratory Health among Cement Workers in Ethiopia

    OpenAIRE

    Zeleke, Zeyede K.

    2011-01-01

    Background: Little is known on dust exposure and respiratory health among cement cleaners. There are only a few follow-up studies on respiratory health among cement factory workers and also studies on acute effects of cement dust exposure are limited in numbers. Objective: This study aimed at assessing cement dust exposure and adverse respiratory health effects among Ethiopian cement production workers, with particular focus on cement cleaners. Method: The first paper was...

  3. Investigation of the glide modes of single crystals of beryllium

    International Nuclear Information System (INIS)

    The flow characteristics of single crystals of beryllium specially oriented for slip along a single plane and a single direction have been thoroughly investigated. The elastic limit and the strain hardening in basal glide have been investigated in the temperature range (-195 deg. C, 400 deg. C) in tension as well as in compression. Observation of the slip lines and of the dislocation configurations have also been made in addition to the mechanical tests. The prismatic slip has been studied in greater detail: tensile tests have been performed on specimens carefully oriented at different temperatures, strain rates and with varying orientations of the basal and of the prism planes. Tests have also been made in the micro-strain range; the slip lines and the dislocation arrangements were observed in detail. The very unusual variation of the elastic limit with temperature is not due to impurities but to a cross slip mechanism. A model of dislocation locking is proposed to account for the experimental results. This mechanism assumes that the a-bar dislocations may also dissociate on the prism planes [101-bar 0]. Various possible dissociations are suggested, the most probable of which corresponds to the phase transformation: Hexagonal close packed to body centered cubic. This proposal can be extended to account for the relative ease of glide on the different systems in the hexagonal close packed metals. (author)

  4. Erosion of beryllium under high-flux plasma impact

    Energy Technology Data Exchange (ETDEWEB)

    Doerner, R.P., E-mail: rdoerner@ucsd.edu [Center for Energy Research, UCSD, La Jolla, CA 92093-0417 (United States); Björkas, C. [EURATOM-Tekes, Department of Physics, University of Helsinki, P.O.B. 64, 00014 Helsinki (Finland); Institute for Energy Research-Plasma Physics, Forchungszentrun Jülich GmbH, 52425 Jülich (Germany); Nishijima, D. [Center for Energy Research, UCSD, La Jolla, CA 92093-0417 (United States); Schwarz-Selinger, T. [Max-Planck Institut für Plasmaphysik, EURATOM Association, Boltzmannstrasse 2, D-85748 Garching (Germany)

    2013-07-15

    Be sputtering yields, measured by weight loss, in PISCES-B are a factor of 5–10 less than that predicted by binary collision approximations. Measurements show the BeO surface is removed early in the plasma bombardment. Modeling of molecular ions (D{sub 2}{sup +} and D{sub 3}{sup +}) species and redeposition cannot explain the difference. Surface morphology that evolves during the exposure reduces the sputtering yield by a factor of 2–3. Plasma fuel atoms retained in the surface decrease the sputtering yield compared to calculations of a pure Be surface. These effects may explain the measured erosion rates in the absence of Be impurities within the plasma. By introducing Be impurity ions into the plasma, it is possible to simulate a controllable amount of redeposition. The weight loss from eroding Be targets, with Be seeding, is unchanged until the concentration of Be ions in the plasma greatly exceeds the sputtering yield in the non-beryllium seeded exposure.

  5. Manufacture of sintered bricks of high density from beryllium oxide

    International Nuclear Information System (INIS)

    Beryllium oxide bricks of nuclear purity 100 x 100 x 50 and 100 x 100 x 100 mm of very high density (between 2.85 and 3.00) are manufactured by sintering under pressure in graphite moulds at temperatures between 1,750 and 1,850 deg. C, and under a pressure of 150 kg/cm2. The physico-chemical state of the saw material is of considerable importance with regard to the success of the sintering operation. In addition, a study of the sintering of a BeO mixture with 3 to 5 per cent of boron introduced in the form of boric acid, boron carbide or elementary boron shows that high densities can only be obtained by sintering under pressure. For technical reasons of manufacture, only the mixture based on boron carbide is used. The sintering is carried out in graphite moulds at 1500 deg. C under 150 kg/cm2 pressure, and bricks can be obtained with density between 2,85 and 2,90. Laboratory studies and the industrial manufacture of various sinters are described in detail. (author)

  6. Beryllium-induced immune response in C3H mice

    Energy Technology Data Exchange (ETDEWEB)

    Benson, J.M.; Bice, D.E.; Nikula, K.J. [and others

    1995-12-01

    Studies conducted at ITRI over the past several years have investigated whether Beagle dogs, monkeys, and mice are suitable models for human chronic beryllium-induced lung disease (CBD). Recent studies have focused on the histopathological and immunopathological changes occurring in A/J and C3H/HeJ mice acutely exposed by inhalation to Be metal. Lung lesions in both strains of mice included focal lymphocyte aggregates comprised primarily of B lymphocytes and lesser amounts of T-helper lymphocytes and microgranulomas consisting chiefly of macrophages and T-helper lymphocytes. The distribution of proliferating cells within the microgranulomas was similar to the distribution of T-helper cells. These results strongly suggested that A/J and C3H/HeJ mice responded to inhaled Be metal in a fashion similar to humans in terms of pulmonary lesions and the apparent in situ proliferation of T-helper cells. Results of these studies confirm lymphocyte involvement in the pulmonary response to inhaled Be metal.

  7. Beryllium abundance in turn-off stars of NGC 6752

    CERN Document Server

    Pasquini, L; Randich, S; Galli, D; Gratton, R G; Wolff, B; Pasquini, Luca; Bonifacio, Piercarlo; Randich, Sofia; Galli, Daniele; Gratton, Raffaele G.

    2006-01-01

    Aims: To measure the beryllium abundance in two TO stars of the Globular Cluster NGC 6752, one oxygen rich and sodium poor, the other presumably oxygen poor and sodium rich. Be abundances in these stars are used to put on firmer grounds the hypothesis of Be as cosmochronometer and to investigate the formation of Globular Clusters. Method:We present near UV spectra with resolution R$\\sim 45000$ obtained with the UVES spectrograph on the 8.2m VLT Kueyen telescope, analysed with spectrum synthesis based on plane parallel LTE model atmospheres. Results:Be is detected in the O rich star with log(Be/H)=-12.04 $\\pm$0.15, while Be is not detected in the other star for which we obtain the upper limit log(Be/H)$<$-12.2. A large difference in nitrogen abundance (1.6 dex) is found between the two stars. Conclusions:The Be measurement is compatible with what found in field stars with the same [Fe/H] and [O/H]. The 'Be age' of the cluster is found to be 13.3 Gyrs, in excellent agreement with the results from main sequen...

  8. Project SAPPHIRE uranium-beryllium dose rate analysis

    International Nuclear Information System (INIS)

    During a six-week period in the fall of 1994 a team of 31 US government and Y-12 personnel packaged and removed several thousand kilograms of material containing highly enriched uranium from the (former Soviet Union) Republic of Kazakhstan for interim storage at the Y-12 Plant in Oak Ridge, Tennessee. This classified mission, known as PROJECT SAPPHIRE, had been initiated at the request of the Kazakhstan government in order to rid itself of possible security problems. Planning for the mission included assurance of the health and safety of the team members, as well as compliance with all local, IAEA, and US government regulations regarding the handling, packaging, transportation, and storage of radioactive and fissile material. The mission classification restrictions were relaxed following the return of the team and material to the United States. The material to be removed, in the form of small billets and rods of uranium metal and uranium-beryllium alloy and oxide powder, was sealed by team members on site into two-liter steel cans. Two or three cans each were loaded into more than 400 IAEA certified fissile material shipping container, and each container was packed into a large steel drum for transport by US Air Force cargo planes to the United States

  9. Waterlike structural and excess entropy anomalies in liquid beryllium fluoride.

    Science.gov (United States)

    Agarwal, Manish; Chakravarty, Charusita

    2007-11-22

    The relationship between structural order metrics and the excess entropy is studied using the transferable rigid ion model (TRIM) of beryllium fluoride melt, which is known to display waterlike thermodynamic anomalies. The order map for liquid BeF2, plotted between translational and tetrahedral order metrics, shows a structurally anomalous regime, similar to that seen in water and silica melt, corresponding to a band of state points for which average tetrahedral (q(tet)) and translational (tau) order are strongly correlated. The tetrahedral order parameter distributions further substantiate the analogous structural properties of BeF2, SiO2, and H2O. A region of excess entropy anomaly can be defined within which the pair correlation contribution to the excess entropy (S2) shows an anomalous rise with isothermal compression. Within this region of anomalous entropy behavior, q(tet) and S2 display a strong negative correlation, indicating the connection between the thermodynamic and the structural anomalies. The existence of this region of excess entropy anomaly must play an important role in determining the existence of diffusional and mobility anomalies, given the excess entropy scaling of transport properties observed in many liquids. PMID:17963376

  10. Electric properties of the Beryllium-11 system in Halo EFT

    International Nuclear Information System (INIS)

    We compute E1 transitions and electric radii in the Beryllium-11 nucleus using an effective field theory that exploits the separation of scales in this halo system. We fix the leading-order parameters of the EFT from measured data on the 1/2+ and 1/2- levels in 11Be and the B(E1) strength for the transition between them. We then obtain predictions for the B(E1) strength for Coulomb dissociation of the 11Be nucleus to the continuum. We also compute the charge radii of the 1/2+ and 1/2- states. Agreement with experiment within the expected accuracy of a leading-order computation in this EFT is obtained. We also discuss how next-to-leading-order (NLO) corrections involving both s-wave and p-wave 10Be-neutron interactions affect our results, and display the NLO predictions for quantities which are free of additional short-distance operators at this order. Information on neutron-10Be scattering in the relevant channels is inferred.

  11. Electron microscope observation of single - crystalline beryllium thin foils; Observation de lames minces monocristallines de beryllium en microscopie electronique

    Energy Technology Data Exchange (ETDEWEB)

    Antolin, J.; Poirier, J.P.; Dupouy, J.M. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1965-07-01

    Thin foils prepared from single crystalline beryllium simples deformed at room temperature, have been observed by transmission electron microscopy. The various deformation modes have been investigated separately, from their early stages and their characteristic dislocation configurations have been observed. Basal slip is characterized at is outset by the presence of numerous dipoles and elongated prismatic loops. More pronounced cold work leads to the formation of dislocation tangles and bundles which eventually give a cellular structure. Prismatic slip begins by the cross-slip of dislocations from the basal plane into the prismatic plane. A cellular structure is equally observed in heavily deformed samples. Sessile dislocations have been observed in twin boundaries; they are produced by reactions between slip dislocations and twin dislocations. Finally, the study of samples quenched from 1100 deg. C and annealed at 200 deg. C has shown that the observed loops lie in prismatic planes and have a Burgers vector b 1/3<1 1 2-bar 0>. (authors) [French] On a observe en microscopie electronique par transmission des lames minces tirees d'eprouvettes monocristallines de beryllium deformees a l'ambiante. On a etudie separement les differents modes de deformation a partir de leur stade elementaire en observant les configurations de dislocations caracteristiques. Le glissement basal est caracterise a son debut par la presence de nombreux dipoles et de boucles prismatiques allongees. Des ecrouissages plus forts conduisent a la formation d'echeveaux et de gerbes qui finissent par donner une structure cellulaire. Le glissement prismatique debute par le glissement des dislocations hors du plan de base dans les plans prismatiques. On trouve egalement une structure cellulaire pour de forts ecrouissages. Dans les joints de macle, on a observe des dislocations sessiles formees par la reaction entre dislocations de macle et dislocations de glissement. Enfin l

  12. Current chemical exposures among Ontario construction workers.

    Science.gov (United States)

    Verma, Dave K; Kurtz, Lawrence A; Sahai, Dru; Finkelstein, Murray M

    2003-12-01

    Current occupational exposures to chemical agents were assessed as part of an epidemiological study pertaining to the cancer and mortality patterns of Ontario construction workers. The task-based exposure assessment involved members from nine construction trade unions. Air samples were taken using personal sampling pumps and collection media. A DustTrak direct-reading particulate monitor was also employed. Exposure assessments included measurements of airborne respirable, inhalable, total, and silica dust; solvents; metals; asbestos; diesel exhaust and man-made mineral fibers (MMMF). In total, 396 single- or multi-component (filter/tube), 798 direct-reading, and 71 bulk samples were collected. The results showed that Ontario construction workers are exposed to potentially hazardous levels of chemical agents. The findings are similar to those reported by other researchers, except for silica exposure. In our study, silica exposure is much lower than reported elsewhere. The difficulty associated with assessing construction workers' exposures is highlighted. PMID:14612300

  13. Motivating Workers in Construction

    Directory of Open Access Journals (Sweden)

    Jason E. Barg

    2014-01-01

    Full Text Available The study of the motivation of construction workers is limited to a relatively small body of knowledge. Although there is considerable research available regarding motivation and productivity, few researchers have provided a comprehensive analysis on the motivation of construction workers. The research stated that productivity in construction has not improved compared to other industry sectors such as manufacturing. This trend has been echoed in publications throughout the past five decades, and suggested that motivation is one of the key factors impacting productivity. This paper offers a comprehensive review of the published work that directly links the key words—construction and motivation. The findings have been presented in five themes, that is, motivation models, environment and culture, incentives and empowerment, and worker management. This paper concludes with two methods suggested by previous researchers to improve motivation of construction workers: (1 relevant worker incentives (intrinsic or extrinsic and (2 improved management practices, specifically regarding communication with workers.

  14. Pneumoconiosis in rubber workers

    International Nuclear Information System (INIS)

    Radiographic survey carried out on rubber workers revealed that 32 % (24/76) of the workers showed pneumoconiosis. The cases of pneumoconiosis were found in workers who had been exposed to dust for more than 10 years. Among the 24 cases of pneumoconiosis, 15 workers had been exposed to talc dust for more than 12 years. Chest radiographs of the rubber workers who had been exposed to dust for more than 10 years demonstrated radiographic findings and incidences as follows; nodular pattern (16 %), fine reticular and granular pattern (52 %), reticular pattern (36 %), irregularity of lung markings (61 %), ground-glass appearance (8 %), and pleural thickening (15 %). Irregular opacities such as fine reticular and granular pattern, reticular pattern and irregularity of lung markings seen to be major radiographic findings of pneumoconiosis of the rubber workers. While, nodular pattern seen in upper and middle lung zones and pleural thickening seen in apices and upper lung zones seen to be minor changes. (author)

  15. Migration of Beryllium via Multiple Exposure Pathways among Work Processes in Four Different Facilities.

    Science.gov (United States)

    Armstrong, Jenna L; Day, Gregory A; Park, Ji Young; Stefaniak, Aleksandr B; Stanton, Marcia L; Deubner, David C; Kent, Michael S; Schuler, Christine R; Virji, M Abbas

    2014-01-01

    Inhalation of beryllium is associated with the development of sensitization; however, dermal exposure may also be important. The primary aim of this study was to elucidate relationships among exposure pathways in four different manufacturing and finishing facilities. Secondary aims were to identify jobs with increased levels of beryllium in air, on skin, and on surfaces; identify potential discrepancies in exposure pathways, and determine if these are related to jobs with previously identified risk. Beryllium was measured in air, on cotton gloves, and on work surfaces. Summary statistics were calculated and correlations among all three measurement types were examined at the facility and job level. Exposure ranking strategies were used to identify jobs with higher exposures. The highest air, glove, and surface measurements were observed in beryllium metal production and beryllium oxide ceramics manufacturing jobs that involved hot processes and handling powders. Two finishing and distribution facilities that handle solid alloy products had lower exposures than the primary production facilities, and there were differences observed among jobs. For all facilities combined, strong correlations were found between air-surface (rp ≥ 0.77), glove-surface (rp ≥ 0.76), and air-glove measurements (rp ≥ 0.69). In jobs where higher risk of beryllium sensitization or disease has been reported, exposure levels for all three measurement types were higher than in jobs with lower risk, though they were not the highest. Some jobs with low air concentrations had higher levels of beryllium on glove and surface wipe samples, suggesting a need to further evaluate the causes of the discrepant levels. Although such correlations provide insight on where beryllium is located throughout the workplace, they cannot identify the direction of the pathways between air, surface, or skin. Ranking strategies helped to identify jobs with the highest combined air, glove, and/or surface exposures

  16. Inherent structure features of beryllium and their influence on the performance polycrystalline metal under different conditions

    International Nuclear Information System (INIS)

    The anisotropy of physical properties of beryllium single crystals resulting from covalent bonds in crystal lattice leads to significant residual thermal microstresses (RTM) in the polycrystalline metal. It is demonstrated experimentally that there is a simple linear dependence between the magnitude of RTM and the ultimate tensile strength. The factors controlling RTM are analysed and in the framework of powder metallurgy process the technological methods of producing beryllium with the needed properties are recommended. Primarily it is necessary to control the quantity and extent of dispersity of intergranular oxide inclusions and mean grain size in combination with the high degree of macro- and microhomogenity of the structure. The requirements to beryllium microstructure for different operating conditions including neutron fluxes and transient temperature fields are formulated. In the framework of the concept under development one can explain formerly not fully understandable effects, which are characteristic of polycrystalline beryllium such as unexpected Petch-Stro curve, the role of twinning etc., and predict new ones. In particular, it can be possible to expect the growth of ductility of high strength beryllium grades as neutron irradiated. (author)

  17. Solid state bonding of beryllium-copper for an ITER first wall application

    International Nuclear Information System (INIS)

    Several different joint assemblies were evaluated in support of a manufacturing technology for diffusion bonding a beryllium armor tile to a copper alloy heat sink for fusion reactor applications. Because beryllium reacts with all but a few elements to form intermetallic compounds, this study considered several different surface treatments as a means of both inhibiting these reactions and promoting a good diffusion bond between the two substrates. All diffusion bonded assemblies used aluminum or an aluminum-beryllium composite (AlBeMet-150) as the interfacial material in contact with beryllium. In most cases, explosive bonding was utilized as a technique for joining the copper alloy heat sink to an aluminum or AlBeMet-150 substrate, which was subsequently diffusion bonded to an aluminum coated beryllium tile. In this approach, a 250 μm thick titanium foil was used as a diffusion barrier between the copper and aluminum to prevent the formation of Cu-Al intermetallic phases. In all cases, a hot isostatic pressing (HIP) furnace was used in conjunction with canned assemblies in order to minimize oxidation and apply sufficient pressure on the assembly for excellent metal-to-metal contact and subsequent bonding. Several different processing schedules were evaluated during the course of this study; bonded assemblies were produced that failed outside the bond area indicating a 100% joint efficiency. (author)

  18. Clinical approach to chronic beryllium disease and other nonpneumoconiotic interstitial lung diseases.

    Science.gov (United States)

    Maier, Lisa A

    2002-10-01

    Exposures in the workplace result in a diverse set of diseases ranging from the pneumoconiosis to other interstitial lung diseases to acute lung injury. Physician awareness of the potential disease manifestations associated with specific exposures is important in defining these diseases and in preventing additional disease. Most occupational diseases mimic other forms of lung disease, including pulmonary fibrosis, sarcoidosis, adult respiratory distress syndrome (ARDS), and bronchiolitis. A "sarcoidosis"-like syndrome, usually limited to the lungs, may result from exposure to bioaerosols and a number of metals. Exposure to beryllium in the workplace produces a granulomatous lung disease clinically indistinguishable from sarcoidosis, chronic beryllium disease (CBD). Beryllium's ability to produce a beryllium-specific immune response is used in the beryllium lymphocyte proliferation tests to confirm a diagnosis of CBD and exclude sarcoidosis. Exposure to other metals must also be considered in the differential diagnosis of sarcoidosis. When an individual presents acutely with ARDS or acute lung injury, an acute inhalational exposure must be considered. Exposure to a number of irritant substances at high levels may cause a "chemical pneumonitis" or acute lung injury, depending on the solubility and physicochemical properties of the substance. Some of the most notable agents include nitrogen and sulfur oxides, phosgene, and smoke breakdown products. Ingestion of paraquat may also result in an ARDS syndrome, with pulmonary fibrosis eventually resulting. Bronchiolitis is a rare manifestation of inhalational exposures but must also be considered in the clinical evaluation of inhalational exposure. PMID:12362066

  19. Inherent structure features of beryllium and their influence on the performance polycrystalline metal under different conditions

    Energy Technology Data Exchange (ETDEWEB)

    Khomutov, A.M.; Mikhailov, V.S.; Pronin, V.N.; Pakhomov, Ya.D. [State Scientific Center of Russian Federation `A.A. Bochvar All-Russia Research Inst. of Inorganic Materials (VNIINM)`, Moscow (Russian Federation)

    1998-01-01

    The anisotropy of physical properties of beryllium single crystals resulting from covalent bonds in crystal lattice leads to significant residual thermal microstresses (RTM) in the polycrystalline metal. It is demonstrated experimentally that there is a simple linear dependence between the magnitude of RTM and the ultimate tensile strength. The factors controlling RTM are analysed and in the framework of powder metallurgy process the technological methods of producing beryllium with the needed properties are recommended. Primarily it is necessary to control the quantity and extent of dispersity of intergranular oxide inclusions and mean grain size in combination with the high degree of macro- and microhomogenity of the structure. The requirements to beryllium microstructure for different operating conditions including neutron fluxes and transient temperature fields are formulated. In the framework of the concept under development one can explain formerly not fully understandable effects, which are characteristic of polycrystalline beryllium such as unexpected Petch-Stro curve, the role of twinning etc., and predict new ones. In particular, it can be possible to expect the growth of ductility of high strength beryllium grades as neutron irradiated. (author)

  20. Parametric studies of carbon erosion mitigation dynamics in beryllium seeded deuterium plasmas

    International Nuclear Information System (INIS)

    The characteristic time of protective beryllium layer formation on a graphite target, τBe/C, has been investigated as a function of surface temperature, Ts, ion energy, Ei, ion flux, Γi, and beryllium ion concentration, cBe, in beryllium seeded deuterium plasma. τBe/C is found to be strongly decreased with increasing Ts in the range of 550-970K. This is thought to be associated with the more efficient formation of beryllium carbide (Be2C). By scanning the parameters, a scaling expression for τBe/C has been derived as τBe/C[s]=1.0x10-7cBe-1.9+/-0.1Ei0.9+/-0.3Γi-0.6+/-0.3exp ((4.8+/-0.5)x103/Ts) where cBe is dimensionless, Ei in eV, Γi in 1022m-2s-1 and Ts in K. Should this scaling extend to an ITER scenario, carbon erosion of the divertor strike point region may be reduced with characteristic time of ∼6ms. This is much shorter than the time between predicted ITER type I ELMs (∼1s), and suggests that protective beryllium layers can be formed in between ELMs, and mitigate carbon erosion.

  1. X-ray drive of beryllium capsule implosions at the National Ignition Facility

    Science.gov (United States)

    Wilson, D. C.; Yi, S. A.; Simakov, A. N.; Kline, J. L.; Kyrala, G. A.; Dewald, E. L.; Tommasini, R.; Ralph, J. E.; Olson, R. E.; Strozzi, D. J.; Celliers, P. M.; Schneider, M. B.; MacPhee, A. G.; Zylstra, A. B.; Callahan, D. A.; Hurricane, O. A.; Milovich, J. L.; Hinkel, D. E.; Rygg, J. R.; Rinderknecht, H. G.; Sio, H.; Perry, T. S.; Batha, S.

    2016-05-01

    National Ignition Facility experiments with beryllium capsules have followed a path begun with “high-foot” plastic capsule implosions. Three shock timing keyhole targets, one symmetry capsule, a streaked backlit capsule, and a 2D backlit capsule were fielded before the DT layered shot. After backscatter subtraction, laser drive degradation is needed to match observed X-ray drives. VISAR measurements determined drive degradation for the picket, trough, and second pulse. Time dependence of the total Dante flux reflects degradation of the of the third laser pulse. The same drive degradation that matches Dante data for three beryllium shots matches Dante and bangtimes for plastic shots N130501 and N130812. In the picket of both Be and CH hohlraums, calculations over-estimate the x-ray flux > 1.8 keV by ∼100X, while calculating the total flux correctly. In beryllium calculations these X-rays cause an early expansion of the beryllium/fuel interface at ∼3 km/s. VISAR measurements gave only ∼0.3 km/s. The X-ray drive on the Be DT capsule was further degraded by an unplanned decrease of 9% in the total picket flux. This small change caused the fuel adiabat to rise from 1.8 to 2.3. The first NIF beryllium DT implosion achieved 29% of calculated yield, compared to CH capsules with 68% and 21%.

  2. Material selection for extended life of the beryllium reflectors in the JMTR

    International Nuclear Information System (INIS)

    The Japan Materials Test Reactor (JMTR) has been one of the most significant high-energy test reactors in the world since achieving its first criticality in 1968. Beryllium has been used as the reflector element material in the reactor, specifically S-200F structural grade beryllium manufactured by Brush Wellman Inc. The JMTR is currently in the process of being refurbished, and the upgraded reactor will return to service in 2011. As a part of the reactor upgrade, the Japan Atomic Energy Agency (JAEA) also has plans to extend the operating lifetime of the beryllium reflector elements. In order to do that, it will first be necessary to determine which of the material's physical and mechanical properties will be the most influential on that choice. Selecting a different grade of beryllium material for the reflector elements to extend operational lifetime under neutron irradiation is discussed in detail. A new plan for irradiation testing to evaluate the various beryllium grades under consideration is also briefly described. (author)

  3. Manufacturing and thermomechanical testing of actively cooled all beryllium high heat flux test pieces

    Energy Technology Data Exchange (ETDEWEB)

    Vasiliev, N.N.; Sokolov, Yu.A.; Shatalov, G.E. [and others

    1995-09-01

    One of the problems affiliated to ITER high heat flux elements development is a problem of interface of beryllium protection with heat sink routinely made of copper alloys. To get rid of this problem all beryllium elements could be used as heat receivers in places of enhanced thermal loads. In accordance with this objectives four beryllium test pieces of two types have been manufactured in {open_quotes}Institute of Beryllium{close_quotes} for succeeding thermomechanical testing. Two of them were manufactured in accordance with JET team design; they are round {open_quotes}hypervapotron type{close_quotes} test pieces. Another two ones are rectangular test sections with a twisted tape installed inside of the circular channel. Preliminary stress-strain analysis have been performed for both type of the test pieces. Hypervapotrons have been shipped to JET where they were tested on JET test bed. Thermomechanical testing of pieces of the type of {open_quotes}swirl tape inside of tube{close_quotes} have been performed on Kurchatov Institute test bed. Chosen beryllium grade properties, some details of manufacturing, results of preliminary stress-strain analysis and thermomechanical testing of the test pieces {open_quotes}swirl tape inside of tube{close_quotes} type are given in this report.

  4. Beryllium and lithium resource requirements for solid blanket designs for fusion reactors

    International Nuclear Information System (INIS)

    The lithium and beryllium requirements are analyzed for an economy of 106 MW(e) CTR3 capacity using solid blanket fusion reactors. The total lithium inventory in fusion reactors is only approximately 0.2 percent of projected U. S. resources. The lithium inventory in the fusion reactors is almost entirely 6Li, which must be extracted from natural lithium. Approximately 5 percent of natural lithium can be extracted as 6Li. Thus the total feed of natural lithium required is approximately 20 times that actually used in fusion reactors, or approximately 4 percent of U. S. resources. Almost all of this feed is returned to the U. S. resource base after 6Li is extracted, however. The beryllium requirements are on the order of 10 percent of projected U. S. resources. Further, the present cost of lithium and the cost of beryllium extraction could both be increased tenfold with only minor effects on CTR capital cost. Such an increase should substantially multiply the economically recoverable resources of lithium and beryllium. It is concluded that there are no lithium or beryllium resource limitations preventing large-scale implementation of solid blanket fusion reactors. (U.S.)

  5. Solid state bonding of beryllium-copper for an ITER first wall application

    Energy Technology Data Exchange (ETDEWEB)

    Odegard, B.C. Jr.; Cadden, C.H. [Sandia National Labs., Livermore, CA (United States)

    1998-01-01

    Several different joint assemblies were evaluated in support of a manufacturing technology for diffusion bonding a beryllium armor tile to a copper alloy heat sink for fusion reactor applications. Because beryllium reacts with all but a few elements to form intermetallic compounds, this study considered several different surface treatments as a means of both inhibiting these reactions and promoting a good diffusion bond between the two substrates. All diffusion bonded assemblies used aluminum or an aluminum-beryllium composite (AlBeMet-150) as the interfacial material in contact with beryllium. In most cases, explosive bonding was utilized as a technique for joining the copper alloy heat sink to an aluminum or AlBeMet-150 substrate, which was subsequently diffusion bonded to an aluminum coated beryllium tile. In this approach, a 250 {mu}m thick titanium foil was used as a diffusion barrier between the copper and aluminum to prevent the formation of Cu-Al intermetallic phases. In all cases, a hot isostatic pressing (HIP) furnace was used in conjunction with canned assemblies in order to minimize oxidation and apply sufficient pressure on the assembly for excellent metal-to-metal contact and subsequent bonding. Several different processing schedules were evaluated during the course of this study; bonded assemblies were produced that failed outside the bond area indicating a 100% joint efficiency. (author)

  6. An assessment of hand hygiene practices of healthcare workers of a semi-urban teaching hospital using the five moments of hand hygiene

    Directory of Open Access Journals (Sweden)

    Emmanuel Olushola Shobowale

    2016-01-01

    Full Text Available Background: Hand hygiene has been described as the cornerstone and starting point in all infection control programs, with the hands of healthcare staff being the drivers and promoters of infection in critically ill patients. The objectives of this study were to access healthcare workers compliance with the World Health Organization (WHO prescribed five moments of hand hygiene as it relates to patient care and to determine the various strata of healthcare workers who are in default of such prescribed practices. Methods: The study was an observational, cross-sectional one. Hand hygiene compliance was monitored using the hand hygiene observation tool developed by the WHO. A nonidentified observer was used for monitoring compliance with hand hygiene. The observational period was over a 60-day period from August 2015 to October 2015. Results: One hundred and seventy-six observations were recorded from healthcare personnel. The highest number of observations were seen in surgery, n = 40. The following were found to be in noncompliance before patient contact - anesthetist P = 0.00 and the Intensive Care Unit P = 0.00 while compliance was seen with senior nurses (certified registered nurse anesthetist [CRNA] P = 0.04. Concerning hand hygiene after the removal of gloves, the following were areas of noncompliance - the emergency room P = 0.00, CRNA P = 0.00, dental P = 0.04, and compliance was seen with surgery P = 0.01. With regards to compliance after touching the patient, areas of noncompliance were the anesthetists P = 0.00, as opposed to CRNA P = 0.00, dental P = 0.00, and Medicine Department P = 0.02 that were compliant. Overall, the rates of compliance to hand hygiene were low. Discussion: The findings however from our study show that the rates of compliance in our local center are still low. The reasons for this could include lack of an educational program on hand hygiene; unfortunately, healthcare workers in developing settings such as ours

  7. Risk compensation behaviours in construction workers' activities.

    Science.gov (United States)

    Feng, Yingbin; Wu, Peng

    2015-01-01

    The purpose of this study was to test whether the construction workers have the tendency of engaging in risk compensation behaviours, and identify the demographic variables, which may influence the extent to which the construction workers may show risk compensation behaviours. Both quantitative (survey) and qualitative (interviews) approaches were used in this study. A questionnaire survey was conducted with all the construction workers on three building construction sites of a leading construction company in Australia. Semi-structured interviews were then conducted to validate the findings of the quantitative research. The findings indicate that workers tend to show risk compensation behaviours in the construction environment. The workers with more working experience, higher education, or having never been injured at work before have a higher tendency to show risk compensation in their activities than the others. The implication is that contractors need to assess the potential influence of workers' risk compensation behaviours when evaluating the effect of risk control measures. It is recommended that supervisors pay more attention to the behavioural changes of those workers who have more experience, higher education, and have never been injured before after the implementation of new safety control measures on construction site. PMID:24134314

  8. Characterization of constrained beryllium pebble beds after neutron irradiation at HFR at high temperatures up to helium production of 3000 appm

    Energy Technology Data Exchange (ETDEWEB)

    Chakin, V., E-mail: vladimir.chakin@kit.edu [Institute for Applied Materials – Applied Materials Physics, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Plarz 1, 76344 Eggenstein-Leopoldshafen (Germany); Rolli, R. [Institute for Applied Materials – Materials and Biomechanics, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Plarz 1, 76344 Eggenstein-Leopoldshafen (Germany); Moeslang, A.; Vladimirov, P.; Kurinskiy, P. [Institute for Applied Materials – Applied Materials Physics, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Plarz 1, 76344 Eggenstein-Leopoldshafen (Germany); Til, S. van; Magielsen, A.J. [Nuclear Research and Consultancy Group, Westerduinweg 3, Postbus 25, 1755 ZG Petten (Netherlands); Zmitko, M. [The European Joint Undertaking for ITER and the Development of Fusion Energy, c/ Josep Pla, no. 2, Torres Diagonal Litoral, Edificio B3, 08019 Barcelona (Spain)

    2013-10-15

    Highlights: • Defragmentation of beryllium pebbles at irradiation temperatures of 873 and 948 K was detected. • Formation of brittle beryllium oxide layers on neutron irradiated beryllium pebbles was detected. • Strong interaction between beryllium pebbles and platinum foil under neutron irradiation was detected. • Strong interaction between beryllium pebbles and austenitic stainless steel under neutron irradiation was detected. -- Abstract: Small constrained beryllium pebble beds as well as unconstrained beryllium pebbles have been irradiated within HIDOBE-01 experiment at HFR, Petten, the Netherlands. Beryllium pebbles with 1 mm diameter produced by Rotating Electrode Method (REM) were investigated after irradiation at 630, 740, 873, and 948 K up to helium production of 3000 appm. Intensive pore and bubble formation occurs in beryllium after 873 K irradiation. In the contact zones of the pebbles enhanced pore formation takes place. Oxidation of beryllium pebble external surfaces is accompanied by partial destruction of oxide layers owing to their high brittleness. Strong interactions between beryllium pebbles and platinum foil, as well as between beryllium and stainless steel at contact zones occur at 873 and 948 K.

  9. HIV/AIDS risk among brothel-based female sex workers in China: Assessing the terms, content, and knowledge of sex work

    Institute of Scientific and Technical Information of China (English)

    Huang,YY; Henderson,GE; Pan,SM; Cohen,MS

    2005-01-01

    Background: Sexual transmission of HIV in China is rapidly increasing, in part driven by commercial sex work. Goal: This article examines variations in occupational control among one type of brothel-based prostitutes in China, and the relationship between the terms and content of this work and the risk of HIV/AIDS. Organizational factors, are discussed as part of the current political, economic, and social context of sex work in China. Study: The analysis is based on ethnographic observation and in-depth interviews conducted in south China in 2000 and 2001 involving 158 female prostitutes from 45 brothels in 4 red light districts. Qualitative analysis of interview and observational data used development of thematic codes measuring occupational control. Results: Brothel-based female sex workers in China are a heterogeneous population, displaying considerable variability in the organization of life and work, relationships with managers and clients, ability to negotiate condom use, knowledge of sexually transmitted diseases and HIV, and occupational identity, all of which may result in different risks of acquiring HIV. Conclusion: HIV prevention activities in China must focus on sociocultural aspects of sex work. Such interventions depend on detailed knowledge of its organization. The results of this study demonstrate the importance of prevention activities directed at the brothel managers and clients, as well as the sex workers.

  10. Temporary foreign workers in British Columbia's construction industry: friends or rivals

    OpenAIRE

    Kim, Ahna

    2009-01-01

    This study assesses the extent to which opposition to temporary foreign workers exists in British Columbia’s construction industry and uses the findings to suggest policies designed to address the concerns of resident workers. Using a survey of resident workers, the study examines the economic rationale behind their opposition to the employment of temporary foreign workers and determines whether skill levels affect the degree of opposition. The survey finds that resident workers are most conc...

  11. A role for cell adhesion in beryllium-mediated lung disease

    Energy Technology Data Exchange (ETDEWEB)

    Hong-geller, Elizabeth [Los Alamos National Laboratory

    2008-01-01

    Chronic beryllium disease (CBD) is a debilitating lung disorder in which exposure to the lightweight metal beryllium (Be) causes the accumulation of beryllium-specific CD4+ T cells in the lung and formation of noncaseating pulmonary granulomas. Treatment for CBD patients who exhibit progressive pulmonary decline is limited to systemic corticosteroids, which suppress the severe host inflammatory response. Studies in the past several years have begun to highlight cell-cell adhesion interactions in the development of Be hypersensitivity and CBD. In particular, the high binding affinity between intercellular adhesion molecule 1 (I-CAM1) on lung epithelial cells and the {beta}{sub 2} integrin LFA-1 on migrating lymphocytes and macrophages regulates the concerted rolling of immune cells to sites of inflammation in the lung. In this review, we discuss the evidence that implicates cell adhesion processes in onset of Be disease and the potential of cell adhesion as an intervention point for development of novel therapies.

  12. Tribological behavior of improved chemically vapor-deposited boron on beryllium

    International Nuclear Information System (INIS)

    Earlier chemical vapor deposition (CVD) experiments with diborane as the boron source gave well-bonded boron films up to 10 μm thick on beryllium, with layered intermetallic compounds below a top layer of boron. The films were nonuniform in thickness and cracked badly when given diffusion heat treatments to produce desired intermetallic compounds. By rotating the beryllium samples during the CVD, films of uniform thickness have now been produced. A variety of compounds of beryllium and boron have been produced on the outer surface of the CVD film by varying the concentration of diborane in the CVD gas. Wear and friction tests performed on various CVD surfaces using sapphire and diamond pins showed remarkable differences in that the CVD boron surface appeared to be substantially more compatible with diamond than with sapphire. The results of these tests are discussed. (Auth.)

  13. A comparison between beryllium and graphite as materials for JET limiters and wall surfaces

    International Nuclear Information System (INIS)

    JET has always been operated with graphite limiters. Carbonisation has been performed from time to time resulting in a temporary reduction of Zeff. However, the latest results at high power (up to 30 MW) indicate that in most cases the impurity content in the plasma is too large to reach near reactor conditions. To reduce the impurity content to a level acceptable in a reactor, it is proposed to use beryllium as a material for the limiters and wall surfaces in JET. This proposal was first made four years ago on the basis of a report comparing the relative merits of beryllium and carbon. This report is now updated in the present paper, which contains three parts, covering the effects of impurities on the plasma performance, the physical and chemical properties of graphite and beryllium and a simple model for the impurity production at the plasma edge. (author)

  14. Measurement of the ultracold-neutron loss coefficient for beryllium powder

    International Nuclear Information System (INIS)

    Reflections of ultracold neutrons (UCN) from beryllium powder have been measured for various layer thickness and various packing densities. On the basis of the experimental data, the reduced UCN loss coefficient for the UCN reflected from the thermally untreated beryllium, η, is found to be η = (1.75 ± 0.35) x 10-4. The previously obtained data on the reflection of UCN from beryllium powder annealed at high temperature are reconsidered. the value obtained for η at room temperature is (6.4 ± 2.5) x 10-5, which exceeds the theoretical value by an order of magnitude. The analysis of the experimental data was carried out by using a modified diffusion theory in which the albedo reflection depends on the packing density

  15. Diamond-turning HP-21 beryllium to achieve an optical surface

    International Nuclear Information System (INIS)

    Investigation of diamond turning on beryllium was made in anticipation of obtaining an optical finish. Although results of past experiences were poor, it was decided to continue diamond turning on beryllium beyond initial failures. By changing speed and using coolant, partial success was achieved. Tool wear was the major problem. Tests were made to establish and plot wear as a function of cutting speed and time. Slower speeds did cause lower wear rates, but at no time did wear reach an acceptable level. The machine, tools, and procedure used were chosen based on the results of preliminary attempts and on previous experience. It was unnecessary to use an air-bearing spindle because tool failure governed the best finish that could be expected. All tools of diamond composition, whether single crystal or polycrystalline, wore at unacceptable rates. Based on present technology, it must be concluded that beryllium cannot be feasibly diamond turned to achieve an optical finish. (22 fig.)

  16. Examination of Beryllium Under Intense High Energy Proton Beam at CERN's HiRadMat Facility

    CERN Document Server

    Ammigan, K; Hurh, P; Zwaska, R; Atherton, A; Caretta, O; Davenne, t; Densham, C; Fitton, M; Loveridge, P; O'Dell, J; Roberts, S; Kuksenko, v; Butcher, M; Calviani, M; Guinchard, M; Losito, R

    2015-01-01

    Beryllium is extensively used in various accelerator beam lines and target facilities as material for beam win- dows, and to a lesser extent, as secondary particle produc- tion targets. With increasing beam intensities of future ac- celerator facilities, it is critical to understand the response of beryllium under extreme conditions to avoid compro- mising particle production efficiency by limiting beam pa- rameters. As a result, the planned experiment at CERN’s HiRadMat facility will take advantage of the test facility’s tunable high intensity proton beam to probe and investigate the damage mechanisms of several grades of beryllium. The test matrix will consist of multiple arrays of thin discs of varying thicknesses as well as cylinders, each exposed to increasing beam intensities. Online instrumentations will acquire real time temperature, strain, and vibration data of the cylinders, while Post-Irradiation-Examination (PIE) of the discs will exploit advanced microstructural characteri- zation and imagin...

  17. The unique bonding characteristics of beryllium and the Group IIA metals

    Science.gov (United States)

    Heaven, Michael C.; Bondybey, Vladimir E.; Merritt, Jeremy M.; Kaledin, Alexey L.

    2011-04-01

    Having closed valence sub-shells, the alkaline earth atoms participate in covalent bonding via orbital hybridization and exchange interactions, with additional contributions from dispersion interactions. Starting from a closed ns2 configuration imparts different characteristics to the chemistry of this group, as compared to metals that have open-shell atomic ground states. Theoretical studies of the bonding of the Group IIA metals have been pursued for many years, and they are known to be challenging for ab initio electronic structure methods. The bonding motifs have been examined, and the differences between beryllium and the remainder of the group explored. Experimental studies that probe the bonding, particularly for beryllium, have lagged behind the theoretical work. In the present Letter we describe our recent spectroscopic and theoretical investigations of simple beryllium compounds, and discuss these results in terms of their relationship to the properties of the heavier Group IIA elements.

  18. Conditions for obtaining extremely pure beryllium by electrolytic refining in alkali chloride fusions

    International Nuclear Information System (INIS)

    Electrorefining is considered a suitable method for producing beryllium with levels of impurity below 1 At.-ppm. Beryllium was electrorefined in a BeCl2-containing LiCl-KCl melt and the key parameters current density, BeCl2 content, electrolyte temperature, composition of crude beryllium, and foreign ion concentration in the melt, together with adjustment of apparatus settings for rotation speed of the cathode, and constitution of crucible material were studied and optimized to achieve a depletion of as many accompanying and alloyed elements as possible. The trace elements were analysed chiefly by means of instrumental neutron activation analysis and atomic absorption spectrometry with electrothermal atomisation, and oxygen and nitrogen determined by vacuum melt extraction or the micro-Kjehldahl method. (orig./IHOE)

  19. The use of a beryllium Hopkinson bar to characterize a piezoresistive accelerometer in shock environments

    Energy Technology Data Exchange (ETDEWEB)

    Bateman, V.I.; Brown, F.A.; Davie, N.T.

    1996-03-01

    The characteristics of a piezoresistive accelerometer in shock environments are being studied at Sandia National Laboratories in the Mechanical Shock Testing Laboratory. A Hopkinson bar capability has been developed to extend our understanding of the piezoresistive accelerometer, in two mechanical configurations, in the high frequency, high shock environments where measurements are being made. In this paper, the beryllium Hopkinson bar configuration with a laser doppler vibrometer as the reference measurement is described. The in-axis performance of the piezoresistive accelerometer for frequencies of dc-50 kHz and shock magnitudes of up to 70,000 g as determined from measurements with a beryllium Hopkinson bar are presented. Preliminary results of characterizations of the accelerometers subjected to cross-axis shocks in a split beryllium Hopkinson bar configuration are presented.

  20. What makes workers happy?

    NARCIS (Netherlands)

    van der Meer, P.H.; Wielers, R.J.J.

    2013-01-01

    This article answers the question what makes workers happy? It does so by combining insights from micro-economics, sociology and psychology. Basis is the standard utility function of a worker that includes income and hours of work and is elaborated with job characteristics. In this way it is possibl

  1. Tritium and helium retention and release from irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Anderl, R.A.; Longhurst, G.R.; Oates, M.A.; Pawelko, R.J. [Idaho National Engineering and Environmental Lab., Idaho Falls, ID (United States)

    1998-01-01

    This paper reports the results of an experimental effort to anneal irradiated beryllium specimens and characterize them for steam-chemical reactivity experiments. Fully-dense, consolidated powder metallurgy Be cylinders, irradiated in the EBR-II to a fast neutron (>0.1 MeV) fluence of {approx}6 x 10{sup 22} n/cm{sup 2}, were annealed at temperatures from 450degC to 1200degC. The releases of tritium and helium were measured during the heat-up phase and during the high-temperature anneals. These experiments revealed that, at 600degC and below, there was insignificant gas release. Tritium release at 700degC exhibited a delayed increase in the release rate, while the specimen was at 700degC. For anneal temperatures of 800degC and higher, tritium and helium release was concurrent and the release behavior was characterized by gas-burst peaks. Essentially all of the tritium and helium was released at temperatures of 1000degC and higher, whereas about 1/10 of the tritium was released during the anneals at 700degC and 800degC. Measurements were made to determine the bulk density, porosity and specific surface area for each specimen before and after annealing. These measurements indicated that annealing caused the irradiated Be to swell, by as much as 14% at 700degC and 56% at 1200degC. Kr gas adsorption measurements for samples annealed at 1000degC and 1200degC determined specific surface areas between 0.04 m{sup 2}/g and 0.1 m{sup 2}/g for these annealed specimens. The tritium and helium gas release measurements and the specific surface area measurements indicated that annealing of irradiated Be caused a porosity network to evolve and become surface-connected to relieve internal gas pressure. (author)

  2. Fundamental hydrogen interactions with beryllium : a magnetic fusion perspective.

    Energy Technology Data Exchange (ETDEWEB)

    Wampler, William R. (Sandia National Laboratories, Albuquerque, NM); Felter, Thomas E.; Whaley, Josh A.; Kolasinski, Robert D.; Bartelt, Norman Charles

    2012-03-01

    Increasingly, basic models such as density functional theory and molecular dynamics are being used to simulate different aspects of hydrogen recycling from plasma facing materials. These models provide valuable insight into hydrogen diffusion, trapping, and recombination from surfaces, but their validation relies on knowledge of the detailed behavior of hydrogen at an atomic scale. Despite being the first wall material for ITER, basic single crystal beryllium surfaces have been studied only sparsely from an experimental standpoint. In prior cases researchers used electron spectroscopy to examine surface reconstruction or adsorption kinetics during exposure to a hydrogen atmosphere. While valuable, these approaches lack the ability to directly detect the positioning of hydrogen on the surface. Ion beam techniques, such as low energy ion scattering (LEIS) and direct recoil spectroscopy (DRS), are two of the only experimental approaches capable of providing this information. In this study, we applied both LEIS and DRS to examine how hydrogen binds to the Be(0001) surface. Our measurements were performed using an angle-resolved ion energy spectrometer (ARIES) to probe the surface with low energy ions (500 eV - 3 keV He{sup +} and Ne{sup +}). We were able to obtain a 'scattering maps' of the crystal surface, providing insight on how low energy ions are focused along open surface channels. Once we completed a characterization of the clean surface, we dosed the sample with atomic hydrogen using a heated tungsten capillary. A distinct signal associated with adsorbed hydrogen emerged that was consistent with hydrogen residing between atom rows. To aid in the interpretation of the experimental results, we developed a computational model to simulate ion scattering at grazing incidence. For this purpose, we incorporated a simplified surface model into the Kalypso molecular dynamics code. This approach allowed us to understand how the incident ions interacted with the

  3. Structure of beryllium isotopes in fermionic molecular dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Torabi, Bahram Ramin

    2009-02-16

    Modern theoretical nuclear physics faces two major challenges. The first is finding a suitable interaction, which describes the forces between nucleons. The second challenge is the solution of the nuclear many-body problem for a given nucleus while applying a realistic potential. The potential used in the framework of this thesis is based on the Argonne AV18 potential. It was transformed by means of the Unitary Correlation Operator Method (UCOM) to optimize convergence. The usual phenomenological corrections were applied to improve the potential for the Hilbert space used in Fermionic Molecular Dynamics (FMD). FMD is an approach to solve the nuclear many-body problem. It uses a single-particle basis which is a superposition of Gaussian distributions in phase-space. The most simple many-body state is the antisymmetric product of the singleparticle states: a Slater determinant, the so called intrinsic state. This intrinsic state is projected on parity, total angular momentum and a center of mass momentum zero. The Hilbert space is spanned by several of these projected states. The states are obtained by minimizing their energy while demanding certain constraints. The expectation values of Slater determinants, parity projected and additionally total angular momentum projected Slater determinants are used. The states that are relevant in the low energy regime are obtained by diagonalization. The lowest moments of the mass-, proton- or neutron-distribution and the excitation in proton- and neutron-shells of a harmonic oscillator are some of the used constraints. The low energy regime of the Beryllium isotopes with masses 7 to 14 is calculated by using these states. Energies, radii, electromagnetic transitions, magnetic moments and point density distributions of the low lying states are calculated and are presented in this thesis. (orig.)

  4. Electron impact ionization cross sections of beryllium-tungsten clusters*

    Science.gov (United States)

    Sukuba, Ivan; Kaiser, Alexander; Huber, Stefan E.; Urban, Jan; Probst, Michael

    2016-01-01

    We report calculated electron impact ionization cross sections (EICSs) of beryllium-tungsten clusters, BenW with n = 1,...,12, from the ionization threshold to 10 keV using the Deutsch-Märk (DM) and the binary-encounter-Bethe (BEB) formalisms. The positions of the maxima of DM and BEB cross sections are mostly close to each other. The DM cross sections are more sensitive with respect to the cluster size. For the clusters smaller than Be4W they yield smaller cross sections than BEB and vice versa larger cross sections than BEB for clusters larger than Be6W. The maximum cross section values for the singlet-spin groundstate clusters range from 7.0 × 10-16 cm2 at 28 eV (BeW) to 54.2 × 10-16 cm2 at 43 eV (Be12W) for the DM cross sections and from 13.5 × 10-16 cm2 at 43 eV (BeW) to 38.9 × 10-16 cm2 at 43 eV (Be12W) for the BEB cross sections. Differences of the EICSs in different isomers and between singlet and triplet states are also explored. Both the DM and BEB cross sections could be fitted perfectly to a simple expression used in modeling and simulation codes in the framework of nuclear fusion research. Contribution to the Topical Issue "Atomic Cluster Collisions (7th International Symposium)", edited by Gerardo Delgado Barrio, Andrey Solov'Yov, Pablo Villarreal, Rita Prosmiti.Supplementary material in the form of one pdf file available from the Journal web page at http://dx.doi.org/10.1140/epjd/e2015-60583-7

  5. Structure of beryllium isotopes in fermionic molecular dynamics

    International Nuclear Information System (INIS)

    Modern theoretical nuclear physics faces two major challenges. The first is finding a suitable interaction, which describes the forces between nucleons. The second challenge is the solution of the nuclear many-body problem for a given nucleus while applying a realistic potential. The potential used in the framework of this thesis is based on the Argonne AV18 potential. It was transformed by means of the Unitary Correlation Operator Method (UCOM) to optimize convergence. The usual phenomenological corrections were applied to improve the potential for the Hilbert space used in Fermionic Molecular Dynamics (FMD). FMD is an approach to solve the nuclear many-body problem. It uses a single-particle basis which is a superposition of Gaussian distributions in phase-space. The most simple many-body state is the antisymmetric product of the singleparticle states: a Slater determinant, the so called intrinsic state. This intrinsic state is projected on parity, total angular momentum and a center of mass momentum zero. The Hilbert space is spanned by several of these projected states. The states are obtained by minimizing their energy while demanding certain constraints. The expectation values of Slater determinants, parity projected and additionally total angular momentum projected Slater determinants are used. The states that are relevant in the low energy regime are obtained by diagonalization. The lowest moments of the mass-, proton- or neutron-distribution and the excitation in proton- and neutron-shells of a harmonic oscillator are some of the used constraints. The low energy regime of the Beryllium isotopes with masses 7 to 14 is calculated by using these states. Energies, radii, electromagnetic transitions, magnetic moments and point density distributions of the low lying states are calculated and are presented in this thesis. (orig.)

  6. Retention and release mechanisms of deuterium implanted into beryllium

    Science.gov (United States)

    Oberkofler, M.; Reinelt, M.; Linsmeier, Ch.

    2011-06-01

    The fraction of deuterium (D) that is retained upon irradiation of beryllium (Be) as well as the temperatures at which implanted D is released are of importance for the international fusion experiment ITER, where Be will be used as an armor material. The influence of single parameters on retention and release is investigated in laboratory experiments performed under well defined conditions with the aim to identify dominant underlying mechanisms and thus be able to predict the behavior of the Be wall in ITER. Recent progress in the quantification of retained fractions and release temperatures as well as in the understanding of the governing mechanisms is presented. The retained fraction upon implantation of D at 1 keV into Be(1 1 2¯ 0) to fluences far below the saturation threshold of 10 21 m -2 is almost 95%, the remaining 5% being attributed to reflection at the surface. At these low fluences, no dependence of the retained fractions on implantation energy is observed. At fluences of the order of 10 21 m -2 and higher, saturation of the irradiated material affects the retention, leading to lower retained fractions. Furthermore, at these fluences the retained fractions decrease with decreasing implantation energies. Differences in the retained fractions from implanted Be(1 1 2¯ 0) and polycrystalline Be are explained by anisotropic diffusion of interstitials during implantation, leading to an amount of surviving D-trap complexes that depends on surface-orientation. Temperature-programmed desorption (TPD) spectra are recorded after implantation of fluences of the order of 10 19 m -2 at various energies and simulated by means of a newly developed code based on coupled reaction-diffusion systems (CRDS). The asymmetric shape of the TPD peaks is reproduced by introducing a local D accumulation process into the model.

  7. Oxide segregation and melting behavior of transient heat load exposed beryllium

    Science.gov (United States)

    Spilker, B.; Linke, J.; Pintsuk, G.; Wirtz, M.

    2016-10-01

    In the experimental fusion reactor ITER, beryllium will be applied as first wall armor material. However, the ITER-like wall project at JET already experienced that the relatively low melting temperature of beryllium can easily be exceeded during plasma operation. Therefore, a detailed study was carried out on S-65 beryllium under various transient, ITER-relevant heat loads that were simulated in the electron beam facility JUDITH 1. Hereby, the absorbed power densities were in the range of 0.15-1.0 GW m-2 in combination with pulse durations of 1-10 ms and pulse numbers of 1-1000. In metallographic cross sections, the emergence of a transition region in a depth of ~70-120 µm was revealed. This transition region was characterized by a strong segregation of oxygen at the grain boundaries, determined with energy dispersive x-ray spectroscopy element mappings. The oxide segregation strongly depended on the maximum temperature reached at the end of the transient heat pulse in combination with the pulse duration. A threshold for this process was found at 936 °C for a pulse duration of 10 ms. Further transient heat pulses applied to specimens that had already formed this transition region resulted in the overheating and melting of the material. The latter occurred between the surface and the transition region and was associated with a strong decrease of the thermal conductivity due to the weakly bound grains across the transition region. Additionally, the transition region caused a partial separation of the melt layer from the bulk material, which could ultimately result in a full detachment of the solidified beryllium layers from the bulk armor. Furthermore, solidified beryllium filaments evolved in several locations of the loaded area and are related to the thermally induced crack formation. However, these filaments are not expected to account for an increase of the beryllium net erosion.

  8. Chronology of the beryllium replacement shutdown at the High Flux Isotope Reactor (HFIR), 1983

    International Nuclear Information System (INIS)

    In addition to the permanent beryllium reflector, several other components were replaced. The outer shroud and lower tracks were replaced. The new control rod access plugs and the upper tracks were installed. Replacement of collimator tubes for HB-1 and -2 are tentatively slated for the next permanent beryllium changeout. Inspection of the reactor vessel, the vessel-to-nozzle welds, core support structure, and vessel internal cladding showed them to be in acceptable condition. The highest, accumulative radiation doses received by Reactor Operations personnel during the shutdown, in mrem, were 665, 606, and 560; the highest for P and E personnel were 520, 505, and 475

  9. Structural Basis of Chronic Beryllium Disease: Linking Allergic Hypersensitivity and Autoimmunity

    OpenAIRE

    Clayton, Gina M.; Wang, Yang; Crawford, Frances; Novikov, Andrey; Wimberly, Brian T.; Kieft, Jeffrey S.; Falta, Michael T.; Bowerman, Natalie A.; Marrack, Philippa; Fontenot, Andrew P.; Dai, Shaodong; John W Kappler

    2014-01-01

    T cell-mediated hypersensitivity to metal cations is common in humans. How the T cell antigen receptor (TCR) recognizes these cations bound to a major histocompatibility complex (MHC) protein and self-peptide is unknown. Individuals carrying the MHCII allele, HLA-DP2, are at risk for chronic beryllium disease (CBD), a debilitating inflammatory lung condition caused by the reaction of CD4 T cells to inhaled beryllium. We show here that the T cell ligand is created when a Be2+ cation becomes bu...

  10. Isothermal compression and phase transition in beryllium to 28.3 GPa

    International Nuclear Information System (INIS)

    In situ high-pressure x-ray diffraction data for polycrystalline beryllium to 28.3 GPa at ambient temperature show that beryllium is transformed from the HCP phase (I) into a slightly distorted HCP phase (II) at pressures between 8.6 and 14.5 GPa. The volume change for the transition is extremely small (approx. 0.4%); the effect of pressure on the c/a ratio for both the Be(I) and Be(II) phases is also very small. (author)

  11. Measurement of neutron yield by 62 MeV proton beam on a thick Beryllium target

    CERN Document Server

    Alba, R; Boccaccio, P; Celentano, A; Colonna, N; Cosentino, G; Del Zoppo, A; Di Pietro, A; Esposito, J; Figuera, P; Finocchiaro, P; Kostyukov, A; Maiolino, C; Osipenko, M; Ricco, G; Ripani, M; Viberti, C M; Santonocito, D; Schillaci, M

    2012-01-01

    In the framework of research on IVth generation reactors and high intensity neutron sources a low-power prototype neutron amplifier was recently proposed by INFN. It is based on a low-energy, high current proton cyclotron, whose beam, impinging on a thick Beryllium converter, produces a fast neutron spectrum. The world database on the neutron yield from thick Beryllium target in the 70 MeV proton energy domain is rather scarce. The new measurement was performed at LNS, covering a wide angular range from 0 to 150 degrees and an almost complete neutron energy interval. In this contribution the preliminary data are discussed together with the proposed ADS facility.

  12. Micromechanical properties of beryllium and other instrument materials, end-of-year-report

    International Nuclear Information System (INIS)

    The objective of the program is to evaluate and understand the micromechanical properties of beryllium and other instrument materials for use in gyroscopes, so that dimensional instability can be improved. Improved dimensional stability is expected to lessen the need to periodically align gyroscopes in service. Drift in alignment has been attributed in part to mass shifts of 0.000001 inches in critical components of gyroscopes. This report consists of two major parts. Part A - Micromechanical properties of instrument grade beryllium. (description of the materials problem, instrumentation to make strain measurements in the range of 10 to the -7 power, and initial results.) Part B - 10 to the -8 power creep measurement system

  13. Migration of Beryllium via Multiple Exposure Pathways among Work Processes in Four Different Facilities

    Science.gov (United States)

    Armstrong, Jenna L.; Day, Gregory A.; Park, Ji Young; Stefaniak, Aleksandr B.; Stanton, Marcia L.; Deubner, David C.; Kent, Michael S.; Schuler, Christine R.; Virji, M. Abbas

    2016-01-01

    Inhalation of beryllium is associated with the development of sensitization; however, dermal exposure may also be important. The primary aim of this study was to elucidate relationships among exposure pathways in four different manufacturing and finishing facilities. Secondary aims were to identify jobs with increased levels of beryllium in air, on skin, and on surfaces; identify potential discrepancies in exposure pathways, and determine if these are related to jobs with previously identified risk. Beryllium was measured in air, on cotton gloves, and on work surfaces. Summary statistics were calculated and correlations among all three measurement types were examined at the facility and job level. Exposure ranking strategies were used to identify jobs with higher exposures. The highest air, glove, and surface measurements were observed in beryllium metal production and beryllium oxide ceramics manufacturing jobs that involved hot processes and handling powders. Two finishing and distribution facilities that handle solid alloy products had lower exposures than the primary production facilities, and there were differences observed among jobs. For all facilities combined, strong correlations were found between air-surface (rp ≥ 0.77), glove-surface (rp ≥ 0.76), and air-glove measurements (rp ≥ 0.69). In jobs where higher risk of beryllium sensitization or disease has been reported, exposure levels for all three measurement types were higher than in jobs with lower risk, though they were not the highest. Some jobs with low air concentrations had higher levels of beryllium on glove and surface wipe samples, suggesting a need to further evaluate the causes of the discrepant levels. Although such correlations provide insight on where beryllium is located throughout the workplace, they cannot identify the direction of the pathways between air, surface, or skin. Ranking strategies helped to identify jobs with the highest combined air, glove, and/or surface exposures

  14. Wavefunction and energy of the 1s22sns configuration in a beryllium atom

    Institute of Scientific and Technical Information of China (English)

    Huang Shi-Zhong; Ma Kun; Yu Jia-Ming; Liu Fen

    2008-01-01

    A new set of trial functions for 1s22sns configurations in a beryllium atom is suggested.A Mathematica program baaed on the variational method is developed to calculate the wavefunctions and energies of 1s22sns (n=3-6)configurations in a beryllium atom.Non-relativistic energy,polarization correction and relativistic correction which include mass correction,one- and two-body Darwin corrections,spin-spin contact interaction and orbit-orbit interaction,are calculated respectively.The results are in good agreement with experimental data.

  15. Feeling refreshed by sleep can predict psychological wellbeing assessed using the general health questionnaire in male workers: a 3-year follow-up study.

    Science.gov (United States)

    Kawada, Tomoyuki

    2012-12-01

    Prediction of psychological wellbeing based on several important predictors was conducted for ensuring maintenance of good mental health. A 3-year follow-up study to determine psychological well-being was conducted in 969 Japanese male workers. Age, body mass index, present history of medication and four lifestyle factors were used for the analysis. A logistic regression analysis revealed that the odds ratio (95% confidence interval) for obtaining a score of ≥4 in the General Health Questionnaire-12-item version, among the subjects who felt refreshed by sleep was 0.559 (0.415-0.753). None of the other factors showed any statistically significant association. Feeling refreshed by sleep was identified as a predictor of maintained psychological wellbeing in this 3-year follow-up study. PMID:23251209

  16. Assessing Burnout in Portuguese Health Care Workers who Care for the Dying: Validity and Reliability of a Burnout Scale Using Exploratory Factor Analysis

    Directory of Open Access Journals (Sweden)

    Carol Gouveia Melo

    2012-11-01

    Full Text Available Aims: The aim of this study was to develop an effective instrument to measure levels of burnout in Health Care Workers (HCWs who care for dying patients and confirm the validity and reliability of the scale. The Burnout scale for workers who care for dying patients was created in 2005, by Gouveia Melo, using items from the Maslach Burnout Inventory (Human Services Survey (Maslach, Jackson, & Leiter, 1997, the Burnout Test (Service Fields (Jerabek, 2001 and items specifically designed for burnout in end-of-life care. Method: The scale was validated with 280 HCWs working in oncology hospitals and in community home care in different parts of the country. The psychometric methods used were exploratory factor analysis using principal components analysis (PCA, Cronbach’s α coefficients, and intra-class correlation coefficients. Results: The initial 40 items were submitted to analysis for suitability of the data and 38 items were chosen for PCA. Results showed 3 main components with 36 items explaining a total of 34.29% of the variance. These factors were emotional exhaustion (15 items, professional fulfillment (14 items and depersonalization (7 items. Cronbach’s α coefficients were .86 for emotional exhaustion, .83 for professional fulfillment and .63 for depersonalization. Pearson bivariate correlations were performed on the 150 participants, with an interval of 4 months for test-retest purposes with intra-class correlations from .55 to .59 in each domain. Convergent and divergent validation showed significant correlations. Conclusions: The validity and reliability of this scale was established, enabling it to be used within the Portuguese population.

  17. Prevalence of the Metabolic Syndrome Among U.S. Workers

    OpenAIRE

    Davila, Evelyn P; Florez, Hermes; Fleming, Lora E.; Lee, David J; Goodman, Elizabeth; William G LeBlanc; Caban-Martinez, Alberto J; Arheart, Kristopher L.; McCollister, Kathryn E.; Christ, Sharon L.; Clark, John C.; Clarke, Tainya

    2010-01-01

    OBJECTIVE Differences in the prevalence of cardiovascular disease (CVD) and its risk factors among occupational groups have been found in several studies. Certain types of workers (such as shift workers) may have a greater risk for metabolic syndrome, a precursor of CVD. The objective of this study was to assess the differences in prevalence and risk of metabolic syndrome among occupational groups using nationally representative data of U.S. workers. RESEARCH DESIGN AND METHODS Data from 8,45...

  18. A Model for Team Managers with Self-serving Workers

    OpenAIRE

    Corgnet, B. (Brice)

    2007-01-01

    We develop a model of team formation in which workers learn about their level of ability. We show that insufficient cooperation may arise as workers learn positively about their own skills. We then build a model for team managers and establish that their objectivity in assessing coworkers' abilities may facilitate cooperation among agents. This is the case because managers are able to design team contracts based on workers' true performances. Our work provides a motive for the existence of te...

  19. Environmental radiation monitoring plan for depleted uranium and beryllium areas, Yuma Proving Ground

    International Nuclear Information System (INIS)

    This Environmental Radiation Monitoring Plan (ERM) discusses sampling soils, vegetation, and biota for depleted uranium (DU) and beryllium (Be) at Yuma Proving Ground (YPG). The existing ERM plan was used and modified to more adequately assess the potential of DU and Be migration through the YPG ecosystem. The potential pathways for DU and Be migration are discussed and include soil to vegetation, soil to animals, vegetation to animals, animals to animals, and animals to man. Sample collection will show DU deposition and will be used to estimate DU migration. The number of samples from each area varies and depends on if the firing range of interest is currently used for DU testing (GP 17A) or if the range is not used currently for DU testing (GP 20). Twenty to thirty-five individual mammals or lizards will be sampled from each transect. Air samples and samples of dust in the air fall will be collected in three locations in the active ranges. Thirty to forty-five sediment samples will be collected from different locations in the arroys near the impact areas. DU and Be sampling in the Hard Impact and Soft Impact areas changed only slightly from the existing ERM. The modifications are changes in sample locations, addition of two sediment transport locations, addition of vegetation samples, mammal samples, and air sampling from three to five positions on the impact areas. Analysis of samples for DU or total U by inductively-coupled mass spectroscopy (ICP/MS), cc spectroscopy, neutron activation analysis (NAA), and kinetic phosphorimetric analysis (KPA) are discussed, and analysis for Be by ICP/MS are recommended. Acquiring total U (no isotope data) from a large number of samples and analysis of those samples with relatively high total U concentrations results in fewer isotopic identifications but more information on U distribution. From previous studies, total U concentrations greater than about 3 times natural background are usually DU by isotopic confirmation

  20. Asthma among mink workers

    DEFF Research Database (Denmark)

    Grøntved, Berit; Carstensen, Ole; Petersen, Rolf;

    2014-01-01

    We report two cases of asthma among mink workers. The first case is about a mink farmer who had asthma that was difficult to treat. In the medical history there was no clear relation to work, and no conclusive work relation with peak flow monitoring. He had a positive histamine release test to mink...... urine. The second case is about a mink farm worker, who had an asthma attack when handling mink furs. Peak flow monitoring showed a clear relation to this work, but there were no signs of allergy. We conclude that these two cases suggest an increased risk of asthma among mink workers....