WorldWideScience

Sample records for beryllium copper joints

  1. Thermal cycling tests of actively cooled beryllium copper joints

    Energy Technology Data Exchange (ETDEWEB)

    Roedig, M.; Duwe, R.; Linke, J.; Schuster, A.; Wiechers, B. [Forschungszentrum Juelich GmbH (Germany)

    1998-01-01

    Screening tests (steady state heating) and thermal fatigue tests with several kinds of beryllium-copper joints have been performed in an electron beam facility. Joining techniques under investigation were brazing with silver containing and silver-free braze materials, hot isostatic pressing (HIP) and diffusion bonding (hot pressing). Best thermal fatigue performance was found for the brazed samples. (author)

  2. The analysis of beryllium-copper diffusion joint after HHF test

    Energy Technology Data Exchange (ETDEWEB)

    Guiniatouline, R.N.; Mazul, I.V. [Efremov Research Institute, St. Petersburg (Russian Federation); Rubkin, S.Y. [Institute of Physical Chemistry, Moscow (Russian Federation)] [and others

    1995-09-01

    The development of beryllium-copper joints which can withstand to relevant ITER divertor conditions is one of the important tasks at present time. One of the main problem for beryllium-copperjoints, is the inter-metallic layers, the strength and life time of joints significantly depends from the width and contents of the intermetallic layers. The objective of this work is to study the diffusion joint of TGP-56 beryllium to OFHC copper after thermal response and thermocyclic tests with beryllium-copper mockup. The BEY test were performed at e-beam facility (EBTS, SNLA). The following methods were used for analyses: the roentgenographic analysis; X-ray spectrum analysis; the fracture graphic analysis. During the investigation the followed studies were done: the analysis of diffusion boundary Be-Cu, which was obtained at the crossection of one of the tiles, the analysis of the debonded surfaces of a few beryllium tiles and corresponding copper parts; the analysis of upper surface of one of the tiles after HHF tests. The results of this work have showed that: the joint roentgenographic and elements analyses indicated the following phases in the diffusion zone: Cu{sub 2}Be ({approximately}170 {mu}m), CuBe ({approximately}30{mu}m), CuBe{sub 2} ({approximately}1 {mu}m) and solid solution of copper in beryllium. The phases Cu{sub 2}Be, CuBe and solid solution of copper in beryllium were indicated using quantitative microanalysis and phases CuBe, CuBe{sub 2}, Cu, Be - by roentgenographic analysis; the source of fracture (initial crack) is located in the central part of the tiles, the crack caused by the influence of residual stresses during cooling of a mock-up after fabrication and developed under the conditions of slow elastic-plastic growing during the process of thermal fatigue testing. The analysis gives the important data about joint`s quality and also may be used for any type of joints and its comparison for ITER applications.

  3. Reactivity test between beryllium and copper

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, H. [Japan Atomic Energy Research Institute, Ibaraki-ken (Japan); Kato, M. [NGK Insulators, Ltd., Aichi-ken (Japan)

    1995-09-01

    Beryllium has been expected for using as plasma facing material on ITER. And, copper alloy has been proposed as heat sink material behind plasma facing components. Therefore, both materials must be joined. However, the elementary process of reaction between beryllium and copper alloy does not clear in detail. For example, other authors reported that beryllium reacted with copper at high temperature, but it was not obvious about the generation of reaction products and increasing of the reaction layer. In the present work, from this point, for clarifying the elementary process of reaction between beryllium and copper, the out-of-pile compatibility tests were conducted with diffusion couples of beryllium and copper which were inserted in the capsule filled with high purity helium gas (6N). Annealing temperatures were 300, 400, 500, 600 and 700{degrees}C, and annealing periods were 100, 300 and 1000h. Beryllium specimens were hot pressed beryllium, and copper specimens were OFC (Oxygen Free Copper).

  4. Beryllium and copper-beryllium alloys; Beryllium und Kupfer-Beryllium-Legierungen

    Energy Technology Data Exchange (ETDEWEB)

    Nagel, Nikolaus [Materion Brush GmbH, Stuttgart (Germany). Operation and Quality/EH and S

    2017-02-15

    The light metal beryllium is a comparatively rare element, which today is primarily derived from bertrandite. It is mainly used as pure metal or in the form of copper-beryllium alloys, e.g., in automotive industry, aerospace, and electrical components. The wide range of applications is mainly attributed to the extremely high rigidity/density ratio. An overview of the history of the metal, its production, and recycling as well as the properties of CuBe alloys are given.

  5. Vacuum Brazing of Beryllium Copper Components for the National Ignition Facility

    Energy Technology Data Exchange (ETDEWEB)

    Tyhurst, C.C.; Cunningham, M.A.

    2002-06-04

    A process for vacuum brazing beryllium copper anode assemblies was required for the Plasma Electrode Pockels Cell System, or PEPC, a component for the National Ignition Facility (NIF). Initial problems with the joint design and wettability of the beryllium copper drove some minor design changes. Brazing was facilitated by plating the joint surface of the beryllium copper rod with silver 0.0006 inch thick. Individual air sampling during processing and swipe tests of the furnace interior after brazing revealed no traceable levels of beryllium.

  6. Preliminary results for explosion bonding of beryllium to copper

    Energy Technology Data Exchange (ETDEWEB)

    Butler, D.J. [Northwest Technical Industries, Inc., Sequim, WA (United States); Dombrowski, D.E. [Brush Wellman, Inc., Cleveland, OH (United States)

    1995-09-01

    This program was undertaken to determine if explosive bonding is a viable technique for joining beryllium to copper substrates. The effort was a cursory attempt at trying to solve some of the problems associated with explosive bonding beryllium and should not be considered a comprehensive research effort. There are two issues that this program addressed. Can beryllium be explosive bonded to copper substrates and can the bonding take place without shattering the beryllium? Thirteen different explosive bonding iterations were completed using various thicknesses of beryllium that were manufactured with three different techniques.

  7. Photodesorption from copper, beryllium, and thin films

    Science.gov (United States)

    Foerster, C. L.; Halama, H. J.; Korn, G.

    Ever increasing circulating currents in electron-positron colliders and light sources demand lower and lower photodesportion (PSD) from the surfaces of their vacuum chambers and their photon absorbers. This is particularly important in compact electron storage rings and B meson factories where photon power of several kw cm(exp -1) is deposited on the surfaces. Given the above factors, we have measured PSD from 1 m long bars of solid copper and solid beryllium, and TiN, Au and C thin films deposited on solid copper bars. Each sample was exposed to about 10(exp 23) photons/m with a critical energy of 500 eV at the VUV ring of the NSLS. PSD was recorded for two conditions: after a 200 C bake-out and after an Ar glow discharge cleaning. In addition, we also measured reflected photons, photoelectrons and desorption as functions of normal, 75 mrad, 100 mrad, and 125 mrad incident photons.

  8. Nanostructured Alloys as an Alternative to Copper-Beryllium

    Science.gov (United States)

    2014-11-19

    bushing applications;  2) Nanometal/composite for high specific strength/stiffness components; and  3) Nanometal cobalt / copper enabled...performance of Integran’s Nanovate cobalt -based and nickel- cobalt metals is superior to copper beryllium (peak hardness); Mechanical Property Summary...Nanostructured Cobalt Alloy 285 ksi (1967 MPa) 225 ksi (1550 MPa) 290 ksi (2000 MPa) 18855 ksi (130 GPa) Copper Beryllium (C17200-TH04) 142 ksi

  9. 40 CFR 468.20 - Applicability; description of the beryllium copper forming subcategory.

    Science.gov (United States)

    2010-07-01

    ... of pollutants into publicly owned treatment works from the forming of beryllium copper alloys. ... beryllium copper forming subcategory. 468.20 Section 468.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS COPPER FORMING POINT SOURCE...

  10. Solid state bonding of beryllium-copper for an ITER first wall application

    Energy Technology Data Exchange (ETDEWEB)

    Odegard, B.C. Jr.; Cadden, C.H. [Sandia National Labs., Livermore, CA (United States)

    1998-01-01

    Several different joint assemblies were evaluated in support of a manufacturing technology for diffusion bonding a beryllium armor tile to a copper alloy heat sink for fusion reactor applications. Because beryllium reacts with all but a few elements to form intermetallic compounds, this study considered several different surface treatments as a means of both inhibiting these reactions and promoting a good diffusion bond between the two substrates. All diffusion bonded assemblies used aluminum or an aluminum-beryllium composite (AlBeMet-150) as the interfacial material in contact with beryllium. In most cases, explosive bonding was utilized as a technique for joining the copper alloy heat sink to an aluminum or AlBeMet-150 substrate, which was subsequently diffusion bonded to an aluminum coated beryllium tile. In this approach, a 250 {mu}m thick titanium foil was used as a diffusion barrier between the copper and aluminum to prevent the formation of Cu-Al intermetallic phases. In all cases, a hot isostatic pressing (HIP) furnace was used in conjunction with canned assemblies in order to minimize oxidation and apply sufficient pressure on the assembly for excellent metal-to-metal contact and subsequent bonding. Several different processing schedules were evaluated during the course of this study; bonded assemblies were produced that failed outside the bond area indicating a 100% joint efficiency. (author)

  11. Historical analysis of airborne beryllium concentrations at a copper beryllium machining facility (1964-2000).

    Science.gov (United States)

    McAtee, B L; Donovan, E P; Gaffney, S H; Frede, W; Knutsen, J S; Paustenbach, D J

    2009-06-01

    Copper beryllium alloys are the most commonly used form of beryllium; however, there have been few studies assessing occupational exposure in facilities that worked exclusively with this alloy versus those where pure metal or beryllium oxide may also have been present. In this paper, we evaluated the airborne beryllium concentrations at a machining plant using historical industrial hygiene samples collected between 1964 and 2000. With the exception of a few projects conducted in the 1960s, it is believed that >95% of the operations used copper beryllium alloy exclusively. Long-term (>120 min) and short-term (machining of copper beryllium-containing parts, as well as finishing operations (e.g., deburring and polishing) and decontamination of machinery. A total of 580 beryllium air samples were analyzed (311 personal and 269 area samples). The average concentration based on area samples (1964-2000) was 0.021 microg m(-3) (SD 0.17 microg m(-3); range 0.00012-2.5 microg m(-3)); 68.8% were below the analytical limit of detection (LOD). The average airborne beryllium concentration, based on all personal samples available from 1964 through the end of 2000 (n = 311), was 0.026 microg m(-3) (SD 0.059 microg m(-3); range 0.019-0.8 microg m(-3)); 97.4% were below the LOD. Personal samples collected from machinists (n = 78) had an average airborne concentration of 0.021 microg m(-3) (SD 0.014 microg m(-3); range 0.019-0.14 microg m(-3)); 97.4% were below the LOD. Airborne concentrations were consistently below the Occupational Safety and Health Administration permissible exposure limit for beryllium (2 microg m(-3)). Overall, the data indicate that for machining operations involving copper beryllium, the airborne concentrations for >95% of the samples were below the contemporaneous occupational exposure limits or the 1999 Department of Energy action level of 0.2 microg m(-3) and, in most cases, were below the LOD.

  12. Ultrasonic evaluation of beryllium-copper diffusion bonds

    Energy Technology Data Exchange (ETDEWEB)

    Jamieson, E.E.

    2000-06-08

    A study was performed to compare the effectiveness of several advanced ultrasonic techniques when used to determine the strength of diffusion bonded beryllium-copper, which heretofore have each been applied to only a few material systems. The use of integrated backscatter calculations, frequency domain reflection coefficients, and time-of-flight variance was compared in their ability to characterize the bond strength in a series of beryllium-copper diffusion bond samples having a wide variation in bond quality. Correlation of integrated backscatter calculations and time-of-flight variance with bond strength was good. Some correlation of the slope of the frequency based reflection coefficient was shown for medium and high strength bonds, while its Y-intercept showed moderate correlation for all bond strengths.

  13. RF surface resistance of copper-on-beryllium at cryogenic temperatures measured by a 22-GHZ demountable cavity

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Jianfei; Krawczyk, F. L. (Frank L.); Kurennoy, S. (Sergey); Schrage, D. L. (Dale L.); Shapiro, A. H. (Alan H.); Tajima, T. (Tsuyoshi); Wood R. L. (Richard L.)

    2003-01-01

    A 22-GHz demountable cavity on the cold head of a compact refrigerator system was used to measure the RF performance of several coppt:r-plated Beryllium samples. The cavity inner surfce was treated by chemical polishing and heat treatment., as well as an OFE copper coupon to provide a baseline for comparison. The measured surhce resistance was reasonable and repeatable during either cooling or warming. Materials tested included four grades of Beryllium, OFE copper, alumina-dispersion strengthened copper (Glidcop), and Cu-plated versions of all of the above. Two coupons, Cuplated on Beryllium 0-30 and 1-70, offered comparable surface resistance to pure OFE copper or Cu-plated Glidcop. The RF surface resistance of Cu-on-Beryllium samples at cryogenic temperatures is reported together with that of other reference materials.

  14. Photoneutron production in tungsten, praseodymium, copper and beryllium by using high energy electron linear accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Jallu, F. E-mail: jalluf@macadam.cea.fr; Lyoussi, A.; Payan, E.; Recroix, H.; Mariani, A.; Nurdin, G.; Buisson, A.; Allano, J

    1999-09-01

    This paper presents comparisons between photoneutron production measurements in tungsten, copper, praseodymium and beryllium, and calculated data resulting from the ELEPHANT (ELEctron, PHoton And Neutron Transport) code. Measurements were made using the DGA/ETCA linear electron accelerator located at Arcueil, France. Bremsstrahlung endpoints varying in the 15-25 MeV energy range were used. Detectors were positioned at different angles with respect to the electron beam axis. Each measured value is compared with the corresponding calculated value.

  15. A joint fracture toughness evaluation of hot-pressed beryllium

    Science.gov (United States)

    Conrad, H.; Sargent, G. A.; Brown, W. F., Jr.

    1977-01-01

    Fracture toughness tests at room temperature were made on three-point bend specimens cut from hot-pressed beryllium obtained from two suppliers. The test specimens had dimensions conforming to ASTM fracture toughness standard E399-72. A total of 42 specimens were machined from each batch of material. Six specimens from each batch were then distributed to seven independent laboratories for testing. The test data from the laboratories were collected and analyzed for differences between the laboratories and the two batches of material. It is concluded that ASTM 399-72 can be used as a valid test procedure for determining the fracture toughness of beryllium, providing that Kf(max) in fatigue cracking could be up to 80 percent of the K(0) value.

  16. Experimental Investigations on Pulsed Nd:YAG Laser Welding of C17300 Copper-Beryllium and 49Ni-Fe Soft Magnetic Alloys

    Science.gov (United States)

    Mousavi, S. A. A. Akbari; Ebrahimzadeh, H.

    2011-01-01

    Copper-beryllium and soft magnetic alloys must be joined in electrical and electro-mechanical applications. There is a high difference in melting temperatures of these alloys which cause to make the joining process very difficult. In addition, copper-beryllium alloys are of age hardenable alloys and precipitations can brittle the weld. 49Ni-Fe alloy is very hot crack sensitive. Moreover, these alloys have different heat transfer coefficients and reflection of laser beam in laser welding process. Therefore, the control of welding parameters on the formation of adequate weld puddle composition is very difficult. Laser welding is an advanced technique for joining of dissimilar materials since it can precisely control and adjust the welding parameters. In this study, a 100W Nd:YAG pulsed laser machine was used for joining 49Ni-Fe soft magnetic to C17300 copper-beryllium alloys. Welding of samples was carried out autogenously by changing the pulse duration, diameter of beam, welding speed, voltage and frequency. The spacing between samples was set to almost zero. The ample were butt welded. It was required to apply high voltage in this study due to high reflection coefficient of copper alloys. Metallography, SEM analysis, XRD and microhardness measurement was used for survey of results. The results show that the weld strength depends upon the chemical composition of the joints. To change the wells composition and heat input of the welds, it was attempted to deviate the laser focus away from the weld centerline. The best strength was achieved by deviation of the laser beam away about 0.1mm from the weld centerline. The result shows no intermetallic compounds if the laser beam is deviated away from the joint.

  17. High-strength braze joints between copper and steel

    Science.gov (United States)

    Kuhn, R. F.

    1967-01-01

    High-strength braze joints between copper and steel are produced by plating the faying surface of the copper with a layer of gold. This reduces porosity in the braze area and strengthens the resultant joint.

  18. PIC-DSMC simulation of a triggered vacuum switch with a copper/beryllium cathode

    Science.gov (United States)

    Fierro, Andrew; Moore, Chris; Moore, Stan; Biedermann, Laura; Hopkins, Matthew

    2016-09-01

    Typical vacuum discharge simulations rely on the injection of neutral or ionized metal vapor from the cathode into an electrically stressed anode-cathode gap. Simultaneous electron emission, also from the cathode, allows for electron-impact ionization of the emitted metal vapor allowing for plasma formation and subsequent closing mechanism to begin. This work looks to analyze the effect of photoemission from the cathode and/or photoionization of metal vapor on the switch closing process through kinetic simulation techniques. A 500 micron anode-cathode gap is chosen with a variable voltage applied to the anode and a grounded half copper, half beryllium cathode. Injection of the metal vapor for both cathode materials is modeled as a linearly ramped flux with a temperature of 1500 K and a bulk velocity (13.2 km/s for Cu and 22 km/s for Be) away from the cathode. Electron-impact excitation of the emitted metal vapor allows for subsequent spontaneous emission of photons which can then photoionize the metal vapor or cause photoemission from the cathode. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. DOE's NNSA under contract DE-AC04-94AL85000.

  19. Effect of uniaxial stress on gallium, beryllium, and copper-doped germanium hole population inversion lasers

    Energy Technology Data Exchange (ETDEWEB)

    Chamberlin, Danielle Russell [Univ. of California, Berkeley, CA (United States)

    1998-05-01

    The effects of stress on germanium lasers doped with single, double, and triple acceptors have been investigated. The results can be explained quantitatively with theoretical calculations and can be attributed to specific changes in the energy levels of acceptors in germanium under stress. In contrast to previous measurements, gallium-doped Ge crystals show a decrease in lasing upon uniaxial stress. The decrease seen here is attributed to the decrease in heavy hole effective mass upon application of uniaxial stress, which results in a decreased population inversion. The discrepancy between this work and previous studies can be explained with the low compensation level of the material used here. Because the amount of ionized impurity scattering in low-compensated germanium lasers is small to begin with, the reduction in scattering with uniaxial stress does not play a significant role in changing the laser operation. Beryllium-doped germanium lasers operate based on a different mechanism of population inversion. In this material it is proposed that holes can transfer between bands by giving their energy to a neutral beryllium atom, raising the hole from the ground to a bound excited state. The free hole will then return to zero energy with some probability of entering the other band. The minimum and maximum E/B ratios for lasing change with uniaxial stress because of the change in effective mass and bound excited state energy. These limits have been calculated for the case of 300 bar [100] stress, and match very well with the observed data. This adds further credence to the proposed mechanism for population inversion in this material. In contrast to Be and Ga-doped lasers, copper-doped lasers under uniaxial stress show an increase in the range of E and B where lasing is seen. To understand this change the theoretical limits for population inversion based on both the optical phonon mechanism and the neutral acceptor mechanism have been calculated. The data are

  20. Extremely low-outgassing material: 0.2% beryllium copper alloy

    Science.gov (United States)

    Watanabe, Fumio

    2004-01-01

    Exploration for low-outgassing materials for use in ultrahigh vacuum and extreme high-vacuum systems is one of the most important topics of a vacuum researcher. We have found that a copper alloy containing 0.2% beryllium (0.2% BeCu) can attain an extremely low hydrogen outgassing rate of 10-14 Pa (H2) m/s order. Almost the entire surface of 0.2% BeCu is dominated by a BeO layer, after a 400 °C×72 h prebakeout treatment in an ultrahigh vacuum. This layer functions as a barrier to the processes of oxidization and permeation of hydrogen. In addition, this layer resists carbon contamination. Temperature-programmed desorption spectra show only a single peak for water at 150 °C and small quantities of any other desorption gases. Therefore, an in situ bakeout process in which the temperature simply ramps up to 150 °C and immediately ramps back down is enough for degassing; it does not require an ordinary sustained-temperature bakeout. Using an outgassing sample consisting of 0.2% BeCu disks housed in a 0.2% BeCu nipple chamber, a lowest outgassing rate of the 5.6×10-14 Pa (H2) m/s was measured by the pressure-rise method after pump cutoff. The pressure-rise versus time curve was completely nonlinear. It rises over time to a constant slope of 1/2 in a log-log plot, due to hydrogen diffusion from the bulk, but this requires over a week at room temperature. The hydrogen outgassing from the 0.2% BeCu bulk is completely dominated by a diffusion-limited mechanism. This article will describe why we obtain such low-outgassing rates with 0.2% BeCu. It is based on the observed surface changes with prebakeout treatment seen by x-ray photoelectron spectroscopy, and the improvement of hydrogen outgassing measurements by the pressure-rise method. A comparison is made to ordinary stainless steel. In addition, the concept of an outgassing reduction method will be discussed from a review of the published ultralow-outgassing data and reduction methods. .

  1. Joint Exploitation of Copper Mine Resources in Liangshan by Jiangxi Copper and Sichuan

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>Recently,Sichuan Institute of Metallurgical Geology & Exploration signed a strategic agreement of cooperation with Jiangxi Copper Group.The two parties will play an active roles in the joint prospecting and exploitation of mine resources in Liangshan,the copper mine

  2. Eta Production at High Transverse Momentum by Negative 520 GeV/c Pions Incident on Beryllium and Copper Targets

    Energy Technology Data Exchange (ETDEWEB)

    Roser, Robert Martin [Univ. of Rochester, NY (United States)

    1994-01-01

    This thesis presents a measurement of the production of high transverse momentum 17 mesons by a 520 GeV /c $\\sqrt{s}$ = 31.2) $\\pi^-$ beam using data collected during the 1990 fixed target run of Fermilab experiment E706. E706 is a second generation fixed target experiment designed to measure direct-photon production in hadron-nucleus collisions. These data provide a clean test of perturbative QCD and serve as a valuable tool for probing hadronic structure. The $\\gamma\\gamma$ decay mode of the $\\eta$ meson was studied using data from a highly segmented electromagnetic lead liquid argon sampling calorimeter. Results are presented for inclusive $\\eta$ production by $\\pi^-$ beams on both beryllium and copper targets. The $\\eta$ to $\\pi^0$ production ratio and the nuclear dependence of the $\\eta$ production cross section are also reported. These results are for $\\eta$'s in the transverse momentum range 3.5 to 9 Ge V / c and the center of mass rapidity range -0.75 to 0.75, and are the highest energy results ever obtained for inclusive $\\eta$ production using a $\\pi^-$ beam.

  3. Influence of nickel and beryllium content on swelling behavior of copper irradiated with fast neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Singh, B.N.; Garner, F.A.; Edwards, D.J. [Pacific Northwest National Lab., Richland, WA (United States); Evans, J.H.

    1996-10-01

    In the 1970`s, the effects of nickel content on the evolution of dislocation microstructures and the formation and growth of voids in Cu-Ni alloys were studied using 1 MeV electrons in a high voltage electron microscope. The swelling rate was found to decrease rapidly with increasing nickel content. The decrease in the swelling rate was associated with a decreasing void growth rate with increasing nickel content at irradiation temperatures up to 450{degrees}C. At 500{degrees}C, both void size and swelling rate were found to peak at 1 and 2% Ni, respectively, and then to decrease rapidly with increasing nickel content. However, recent work has demonstrated that the swelling behavior of Cu-5%Ni irradiated with fission neutrons is very similar for that of pure copper. The present experiments were designed to investigate this apparent discrepancy.

  4. Beryllium 1989

    Energy Technology Data Exchange (ETDEWEB)

    1989-01-01

    The Roskill report on beryllium gives information on the occurrence and reserves, production technology, geographic distribution, consumption and end-uses, stocks, prices and beryllium and health. There is an appendix on international trade statistics. (author).

  5. In-pile thermocycling testing and post-test analysis of beryllium divertor mockups

    Energy Technology Data Exchange (ETDEWEB)

    Giniatulin, R.; Mazul, I. [Efremov Inst., St. Petersburg (Russian Federation); Melder, R.; Pokrovsky, A.; Sandakov, V.; Shiuchkin, A.

    1998-01-01

    The main damaging factors which impact the ITER divertor components are neutron irradiation, cyclic surface heat loads and hydrogen environment. One of the important questions in divertor mockups development is the reliability of beryllium/copper joints and the beryllium resistance under neutron irradiation and thermal cycling. This work presents the experiment, where neutron irradiation and thermocyclic heat loads were applied simultaneously for two beryllium/copper divertor mockups in a nuclear reactor channel to simulate divertor operational conditions. Two mockups with different beryllium grades were mounted facing each other with the tantalum heater placed between them. This device was installed in the active zone of the nuclear reactor SM-2 (Dimitrovgrad, Russia) and the tantalum block was heated by neutron irradiation up to a high temperature. The main part of the heat flux from the tantalum surface was transported to the beryllium surface through hydrogen, as a result the heat flux loaded two mockups simultaneously. The mockups were cooled by reactor water. The device was lowered to the active zone so as to obtain the heating regime and to provide cooling lifted. This experiment was performed under the following conditions: tantalum heater temperature - 1950degC; hydrogen environment -1000 Pa; surface heat flux density -3.2 MW/m{sup 2}; number of thermal cycles (lowering and lifting) -101; load time in each cycle - 200-5000 s; dwell time (no heat flux, no neutrons) - 300-2000 s; cooling water parameters: v - 1 m/s, Tin - 50degC, Pin - 5 MPa; neutron fluence -2.5 x 10{sup 20} cm{sup -2} ({approx}8 years of ITER divertor operation from the start up). The metallographic analysis was performed after experiment to investigate the beryllium and beryllium/copper joint structures, the results are presented in the paper. (author)

  6. MEASUREMENTS OF THE PROPERTIES OF BERYLLIUM FOIL

    Energy Technology Data Exchange (ETDEWEB)

    ZHAO,Y.; WANG,H.

    2000-03-31

    The electrical conductivity of beryllium at radio frequency (800 MHz) and liquid nitrogen temperature were investigated and measured. This summary addresses a collection of beryllium properties in the literature, an analysis of the anomalous skin effect, the test model, the experimental setup and improvements, MAFIA simulations, the measurement results and data analyses. The final results show that the conductivity of beryllium is not as good as indicated by the handbook, yet very close to copper at liquid nitrogen temperature.

  7. Brazing development and interfacial metallurgy study of tungsten and copper joints with eutectic gold copper brazing alloy

    Energy Technology Data Exchange (ETDEWEB)

    Easton, David, E-mail: david.easton@strath.ac.uk [University of Strathclyde, Department of Mechanical Engineering, Glasgow G1 1XJ (United Kingdom); Zhang, Yuxuan; Wood, James; Galloway, Alexander; Robbie, Mikael Olsson [University of Strathclyde, Department of Mechanical Engineering, Glasgow G1 1XJ (United Kingdom); Hardie, Christopher [Culham Centre for Fusion Energy CCFE, Culham Science Centre, Oxfordshire OX14 3DB (United Kingdom)

    2015-10-15

    Highlights: • A eutectic gold–copper brazing alloy has been successfully used to produce a highly wetted brazed joint between tungsten and copper. • Relevant materials for fusion applications. • Mechanical testing of W–AuCu–Cu soon to be performed. - Abstract: Current proposals for the divertor component of a thermonuclear fusion reactor include tungsten and copper as potentially suitable materials. This paper presents the procedures developed for the successful brazing of tungsten to oxygen free high conductivity (OFHC) copper using a fusion appropriate gold based brazing alloy, Orobraze 890 (Au80Cu20). The objectives were to develop preparation techniques and brazing procedures in order to produce a repeatable, defect free butt joint for tungsten to copper. Multiple brazing methods were utilised and brazing parameters altered to achieve the best joint possible. Successful and unsuccessful brazed specimens were sectioned and analysed using optical and scanning electron microscopy, EDX analysis and ultrasonic evaluation. It has been determined that brazing with Au80Cu20 has the potential to be a suitable joining method for a tungsten to copper joint.

  8. Reliability design and assessment of a micro-probe using the results of a tensile test of a beryllium-copper alloy thin film

    Science.gov (United States)

    Park, Jun-Hyub; Shin, Myung-Soo

    2011-09-01

    This paper describes the results of tensile tests for a beryllium-copper (BeCu) alloy thin film and the application of the results to the design of a probe. The copper alloy films were fabricated by electroplating. To obtain the tensile characteristics of the film, the dog-bone type specimen was fabricated by the etching method. The tensile tests were performed with the specimen using a test machine developed by the authors. The BeCu alloy has an elastic modulus of 119 GPa and the 0.2% offset yield and ultimate tensile strengths of 1078 MPa and 1108 MPa, respectively. The design and manufacture of a smaller probe require higher pad density and smaller pad-pitch chips. It should be effective in high-frequency testing. For the design of a new micro-probe, we investigated several design parameters that may cause problems, such as the contact force and life, using the tensile properties and the design of experiment method in conjunction with finite element analysis. The optimal dimensions of the probe were found using the response surface method. The probe with optimal dimensions was manufactured by a precision press process. It was verified that the manufactured probe satisfied the life, the contact force and the over drive through the compression tests and the life tests of the probes.

  9. Beryllium Toxicity

    Science.gov (United States)

    ... aerospace, aircraft manufacture and maintenance, computer, dental laboratories, telecommunications, and foundries and metal reclamation. How Can I ... if exposure stops. Beryllium usually affects the respiratory system, although it can affect other parts of the ...

  10. Chronic Beryllium Disease

    Science.gov (United States)

    ... Science Education & Training Home Conditions Chronic Beryllium Disease Chronic Beryllium Disease Make an Appointment Find a Doctor ... MD, MSPH, FCCP (February 01, 2016) What is chronic beryllium disease (CBD)? Chronic beryllium disease (CBD) is ...

  11. Extensive Characterisation of Copper-clad Plates, Bonded by the Explosive Technique, for ITER Electrical Joints

    CERN Document Server

    Langeslag, S A E; Libeyre, P; Gung, C Y

    2015-01-01

    Cable-in-conduit conductors will be extensively implemented in the large superconducting magnet coils foreseen to confine the plasma in the ITER experiment. The design of the various magnet systems imposes the use of electrical joints to connect unit lengths of superconducting coils by inter-pancake coupling. These twin-box lap type joints, produced by compacting each cable end in into a copper - stainless steel bimetallic box, are required to be highly performing in terms of electrical and mechanical prop- erties. To ascertain the suitability of the first copper-clad plates, recently produced, the performance of several plates is studied. Validation of the bonded interface is carried out by determining microstructural, tensile and shear characteristics. These measure- ments confirm the suitability of explosion bonded copper-clad plates for an overall joint application. Additionally, an extensive study is conducted on the suitability of certain copper purity grades for the various joint types.

  12. Thermal conductance measurements of bolted copper joints for SuperCDMS

    Energy Technology Data Exchange (ETDEWEB)

    Schmitt, R.; Tatkowski, Greg; Ruschman, M.; Golwala, S. R.; Kellaris, N.; Daal, M.; Hall, Jeter C.; Hoppe, Eric W.

    2015-09-01

    Joint thermal conductance testing has been undertaken for bolted copper to copper connections from 60 mK to 26 K. This testing was performed to validate an initial design basis for the SuperCDMS experiment, where a dilution refrigerator will be coupled to a cryostat via multiple bolted connections. Copper used during testing was either gold plated or passivated with citric acid to prevent surface oxidation. Results obtained are well fit by a power law regression of joint thermal conductance to temperature and match well with data collected during a literature review.

  13. Effect of laser surface melting treatment on properties of electric copper busbar joints

    Institute of Scientific and Technical Information of China (English)

    梁工英; 宋晓平; 顾林喻

    2001-01-01

    Electrical conductance and temperature of electric copper busbar joints were measured under different torque moments. Experimental results show that laser surface melting can increase hardness and refine structure of the copper, and it does not deteriorate electric resistance. Meanwhile, the temperature of laser treated joints under electric current is slightly lower than that of original sample. Salt spray test shows that laser treated sample has better salt spray corrosion resistance than the original sample does. The electric resistance of both laser-treated and original samples are increased with salt spray time. For the same salt spray time, the electric resistance of busbar joint is decreased with increasing torque moment.

  14. Genotoxicology: Single and Joint Action of Copper and Zinc to ...

    African Journals Online (AJOL)

    Michael Horsfall

    ABSTRACT: The genotoxicity of copper, zinc and their binary mixture was examined in. Synodontis clarias and ... Capacity of the water body to support aquatic life as well as its suitability for ... humans (Merian, 1991; DWAF, 1996). In addition,.

  15. The interfacial structure of plated copper alloy resistance spot welded joint

    Science.gov (United States)

    Wu, Jingwei; Zhai, Guofu; Chen, Qing; Wang, Jianqi; Ren, Gang

    2008-09-01

    Plated copper alloys are widely used in electron industry. The plating lay caused the farther decreasing of the welding property of copper alloys, whose intrinsic weldability was poor. In this paper, the bronze and brass specimens with nickel-tin double plating layer were joined by resistance spot welding method. The microstructure and peel strength of the joints were investigated. The experiment results show that a sandwich-like structure was obtained in the faying surface after welding, and the nickel plating layer thickness had severe effect on the reliability of the joints.

  16. The interfacial structure of plated copper alloy resistance spot welded joint

    Energy Technology Data Exchange (ETDEWEB)

    Wu Jingwei [Xiamen Hongfa Electroacoustic Co., Ltd, 361021 Xiamen (China); Harbin Institute of Technology, 150001 Harbin (China)], E-mail: jingweiwu.hit@gmail.com; Zhai Guofu [Harbin Institute of Technology, 150001 Harbin (China); Chen Qing; Wang Jianqi; Ren Gang [Xiamen Hongfa Electroacoustic Co., Ltd, 361021 Xiamen (China)

    2008-09-15

    Plated copper alloys are widely used in electron industry. The plating lay caused the farther decreasing of the welding property of copper alloys, whose intrinsic weldability was poor. In this paper, the bronze and brass specimens with nickel-tin double plating layer were joined by resistance spot welding method. The microstructure and peel strength of the joints were investigated. The experiment results show that a sandwich-like structure was obtained in the faying surface after welding, and the nickel plating layer thickness had severe effect on the reliability of the joints.

  17. Joining of Beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, A

    2006-02-01

    A handbook dealing with the many aspects of beryllium that would be important for the users of this metal is currently being prepared. With an introduction on the applications, advantages and limitations in the use of this metal the following topics will be discussed in this handbook: physical, thermal, and nuclear properties; extraction from the ores; purification and casting of ingots; production and types of beryllium powders; consolidation methods, grades, and properties; mechanical properties with emphasis on the various factors affecting these properties; forming and mechanical working; welding, brazing, bonding, and fastening; machining; powder deposition; corrosion; health aspects; and examples of production of components. This report consists of ''Section X--Joining'' from the handbook. The prefix X is maintained here for the figures, tables and references. In this section the different methods used for joining beryllium and the advantages, disadvantages and limitations of each are presented. The methods discussed are fusion welding, brazing, solid state bonding (diffusion bonding and deformation bonding), soldering, and mechanical fastening. Since beryllium has a high affinity for oxygen and nitrogen with the formation of oxides and nitrides, considerable care must be taken on heating the metal, to protect it from the ambient atmosphere. In addition, mating surfaces must be cleaned and joints must be designed to minimize residual stresses as well as locations for stress concentration (notch effects). In joining any two metals the danger exists of having galvanic corrosion if the part is subjected to moisture or to any type of corroding environment. This becomes a problem if the less noble (anodic) metal has a significantly smaller area than the more noble (cathodic) metal since the ions (positive charges) from the anodic (corroding) metal must correspond to the number of electrons (negative charges) involved at the cathode. Beryllium

  18. Diffusion Bonding Beryllium to Reduced Activation Ferritic Martensitic Steel: Development of Processes and Techniques

    Science.gov (United States)

    Hunt, Ryan Matthew

    Only a few materials are suitable to act as armor layers against the thermal and particle loads produced by magnetically confined fusion. These candidates include beryllium, tungsten, and carbon fiber composites. The armor layers must be joined to the plasma facing components with high strength bonds that can withstand the thermal stresses resulting from differential thermal expansion. While specific joints have been developed for use in ITER (an experimental reactor in France), including beryllium to CuCrZr as well as tungsten to stainless steel interfaces, joints specific to commercially relevant fusion reactors are not as well established. Commercial first wall components will likely be constructed front Reduced Activation Ferritic Martensitic (RAFM) steel, which will need to be coating with one of the three candidate materials. Of the candidates, beryllium is particularly difficult to bond, because it reacts during bonding with most elements to form brittle intermetallic compounds. This brittleness is unacceptable, as it can lead to interface crack propagation and delamination of the armor layer. I have attempted to overcome the brittle behavior of beryllium bonds by developing a diffusion bonding process of beryllium to RAFM steel that achieves a higher degree of ductility. This process utilized two bonding aids to achieve a robust bond: a. copper interlayer to add ductility to the joint, and a titanium interlayer to prevent beryllium from forming unwanted Be-Cu intermetallics. In addition, I conducted a series of numerical simulations to predict the effect of these bonding aids on the residual stress in the interface. Lastly, I fabricated and characterized beryllium to ferritic steel diffusion bonds using various bonding parameters and bonding aids. Through the above research, I developed a process to diffusion bond beryllium to ferritic steel with a 150 M Pa tensile strength and 168 M Pa shear strength. This strength was achieved using a Hot Isostatic

  19. Electrical, Corrosion, and Mechanical Properties of Aluminum-Copper Joints Produced by Explosive Welding

    Science.gov (United States)

    Acarer, Mustafa

    2012-11-01

    This study investigates the microstructure, electrical, corrosion, and mechanical properties of plate-shaped aluminum-copper couple produced using the explosive welding method. Mechanical tests, including hardness, tensile, tensile-shear, and impact test, concluded that the Al-Cu bimetal had an acceptable joint resistance. In this study, local intermetallic regions formed on the interface of the joint of the aluminum-copper bimetal, produced using the explosive welding technique. However, the formed intermetallic regions had no significant effect on the mechanical properties of the joint, except for increasing its hardness. According to electrical conductivity tests, the Al-Cu bimetal had an average electrical conductivity in comparison to the electrical conductivity of aluminum and copper, which were the original materials forming the joint. According to the results of electro-chemical corrosion test, during which galvanic corrosion formed, the Al side of the Al-Cu bimetal was more anodic due to its high electronegativity; as a result, it was exposed to more corrosion in comparison to the copper side.

  20. Vacuum Bellows, Vacuum Piping, Cryogenic Break, and Copper Joint Failure Rate Estimates for ITER Design Use

    Energy Technology Data Exchange (ETDEWEB)

    L. C. Cadwallader

    2010-06-01

    The ITER international project design teams are working to produce an engineering design in preparation for construction of the International Thermonuclear Experimental Reactor (ITER) tokamak. During the course of this work, questions have arisen in regard to safety barriers and equipment reliability as important facets of system design. The vacuum system designers have asked several questions about the reliability of vacuum bellows and vacuum piping. The vessel design team has asked about the reliability of electrical breaks and copper-copper joints used in cryogenic piping. Research into operating experiences of similar equipment has been performed to determine representative failure rates for these components. The following chapters give the research results and the findings for vacuum system bellows, power plant stainless steel piping (amended to represent vacuum system piping), cryogenic system electrical insulating breaks, and copper joints.

  1. Interfacial structure and joint strengthening in arc brazed galvanized steels with copper based filler

    Institute of Scientific and Technical Information of China (English)

    LI Rui-feng; YU Zhi-shui; QI Kai

    2006-01-01

    Galvanized steel sheets were joined by tungsten inert gas(TIG) and metal inert gas(MIG) brazing process using copper based filler. The results show that the joint zone hardness is higher than that of the base material or copper filler from the microhardness tests of TIG brazing specimens, and the fracture spot is at the base materials zone from the tensile tests of MIG brazing specimens. Examination using energy dispersive X-ray analysis reveals the presence of intermetallic compound Fe5Si3(Cu) in the joint. The dispersal of fine Fe5Si3(Cu) particles is the main strengthening factor for the joint. The Fe5Si3(Cu) particles are determined to arise from three sources, namely, spot micro-melt, whisker-like fragmentation and dissolve-separation actions.

  2. Diffusion-bonded beryllium aluminum optical structures

    Science.gov (United States)

    Grapes, Thomas F.

    2003-12-01

    Beryllium aluminum material can present significant advantages for optical support structures. A likely advantage of beryllium aluminum compared to aluminum or titanium for such structures is its higher specific stiffness. However, beryllium aluminum material is significantly more expensive than most competing materials. The cost problem with beryllium aluminum is exacerbated if fabrication methods that result in near net shape parts are not used. Near net shape methods result in the least amount of material "thrown away" in the fabrication process. Casting is a primary example of near net shape manufacturing that is appropriate for some optical support structures. Casting aluminum, and other materials as well, is common. Casting of beryllium aluminum is very difficult, however, and has not had significant success. Diffusion bonding - a different approach for achieving near net shape beryllium aluminum optical support structures, was pursued and accomplished. Diffusion bonding is a term used to describe the joining of solid metal pieces under high temperature and pressure, but without melting. Three different optical support structures were designed and built of beryllium aluminum using diffusion bonding. Relatively small solid beryllium aluminum pieces were arranged together and then joined under hot isostatic pressure conditions. The resulting relatively large pressure bonded part was then machined to achieve the final product. Significant cost savings as compared to machining the part from a solid block were realized. Difficulties achieving diffusion bonds in complex joints were experienced and addressed.

  3. Structure of the transition zone and its influence on the strength of copper-tantalum joint (Explosion welding)

    Science.gov (United States)

    Greenberg, B. A.; Ivanov, M. A.; Rybin, V. V.; Elkina, O. A.; Patselov, A. M.; Antonova, O. V.; Inozemtsev, A. V.; Salishchev, G. A.; Kozhevnikov, V. E.

    2012-10-01

    The joint of copper and tantalum, metals without mutual solubility, formed by explosion welding is studied. The mechanism of the influence of mutual solubility on the structure of the transition zone is established. It is demonstrated that the interface contains heterogeneities, and their role in the strength of the materials joint is revealed. A microheterogeneous structure of the joint zones is detected.

  4. 非真空熔铸铍铜合金大规格铸锭的研究%Research on using non-vacuum melting furnace to cast the large-size ingot of beryllium copper

    Institute of Scientific and Technical Information of China (English)

    马俊杰; 潘建立; 李永华

    2012-01-01

    The time for melting and insolating is very long when non-vacuum melt furnace is used to cast the large-size ingot of beryllium copper.Because of the rate of oxidation and melting loss for beryllium is about 0.004 4% per minute,the beryllium in the melt is declining,so that the beryllium content disparity between the different of ingot,or the same ingot for between top and end would be higher than 6%.Much of beryllium and master alloy's melting loss may cause the inclusion,and then reduce the yield.At the same times,beryllium has a strong deoxidization,the melt suction will be easy,and the results are that the ingot will emerge the casting defects easily,such as porosity and more.By the hundreds of researching every detail of the casting process,a rational casting process was found finally.The beryllium and other metal's melting loss are lower than 6%,3% in the casting process by controlling.The deviation of the content of the beryllium is lower than 4%.The rate of the ingot's finished products is higher than 80%.%在非真空熔铸铍铜合金大规格铸锭时,需要长时间的熔化和保温.由于铍在金属熔体中的氧化烧损量达到0.004 4%/min以上,熔体中的铍质量分数处于不断下降的状态,因而不同铸锭之间、同一铸锭头尾w(Be)偏差达到6%以上;铍及铍铜原料的大量烧损容易导致铸锭夹杂,进而影响铸锭的综合成品率;同时,由于铍具有强烈的脱氧作用,熔体极易吸气,铸锭内部容易出现气孔等铸造缺陷.通过上百炉次的试验,对熔铸工艺的每个细节深入研究和试验,确定了合理的熔铸工艺,在生产铍铜合金大规格铸锭时,铍及铍铜材料的烧损率分别降到6%及3%以下,铸锭化学成分偏差≤4%,铸锭综合成品率达到80%以上.

  5. Structure formation and properties of a copper-aluminum joint produced by ultrasound-assisted explosive welding

    Science.gov (United States)

    Kuz'min, E. V.; Peev, A. P.; Kuz'min, S. V.; Lysak, V. I.

    2017-08-01

    The effect of ultrasound-assisted explosive welding on the structure formation and the properties of copper-aluminum joints is studied. Ultrasound-assisted explosive welding improves the quality of formed copper-aluminum joints, i.e., enhances their strength and significantly reduces the amount of fused metal over the entire weldability range. It is shown that ultrasound-assisted explosive welding can noticeably extend the weldability range of the copper-aluminum pair to obtain equal-in-strength joints with minimum structural heterogeneity in the wide welding range.

  6. Effects of processing conditions and ambient environment on the microstructure and fracture strength of copper/niobium/copper interlayer joints for alumina

    Energy Technology Data Exchange (ETDEWEB)

    Marks, Robert Alan [Univ. of California, Berkeley, CA (United States)

    1999-12-01

    Partial transient liquid phase (PTLP) bonding is a technique which can be used to join ceramics with metals and is used to form niobium-based joints for alumina. The principal advantage to PTLP bonding is that it enables refractory joints to be fabricated at temperatures below those typically required by solid state diffusion bonding. A thorough review of the important parameters (chemical compatibility, thermal expansion match, sufficient wettability of the liquid phase on the solid phases) in choosing a joining material for ceramics by the PTLP method is provided. As in conventional PTLP joining, the current study uses thin (=3 μm) copper layers sandwiched between the alumina (bulk) and niobium (127 μm). However, unlike the case of copper/nickel/copper obium is limited. Consequently, the copper is not entirely dissolved in the process, resulting in a two phase (copper-rich and niobium-rich phases) microstructure. Different processing conditions (temperature and applied load) result in different morphologies of the copper-rich and niobium-rich phases at the interface. These different microstructures exhibit distinct strength characteristics. Extended annealing of as-processed joints can influence the strengths differently depending on the ambient partial oxygen pressure at the annealing temperature. The focus of this work is to correlate processing conditions, microstructure, and resulting joint strength. Under optimum processing conditions (1400°C, 2.2 MPa), joints with strengths in excess of 200 MPa at 1200°C are fabricated.

  7. Fiber laser welding of austenitic steel and commercially pure copper butt joint

    Science.gov (United States)

    Kuryntsev, S. V.; Morushkin, A. E.; Gilmutdinov, A. Kh.

    2017-03-01

    The fiber laser welding of austenitic stainless steel and commercially pure copper in butt joint configuration without filler or intermediate material is presented. In order to melt stainless steel directly and melt copper via heat conduction a defocused laser beam was used with an offset to stainless steel. During mechanical tests the weld seam was more durable than heat affected zone of copper so samples without defects could be obtained. Three process variants of offset of the laser beam were applied. The following tests were conducted: tensile test of weldment, intermediate layer microhardness, optical metallography, study of the chemical composition of the intermediate layer, fractography. Measurements of electrical resistivity coefficients of stainless steel, copper and copper-stainless steel weldment were made, which can be interpreted or recalculated as the thermal conductivity coefficient. It shows that electrical resistivity coefficient of cooper-stainless steel weldment higher than that of stainless steel. The width of intermediate layer between stainless steel and commercially pure copper was 41-53 μm, microhardness was 128-170 HV0.01.

  8. Joint Toxicity of Two Phthalates with Waterborne Copper to Daphnia magna and Photobacterium phosphoreum.

    Science.gov (United States)

    Huang, Boyang; Li, Dinglong; Yang, Yan

    2016-09-01

    Di-n-butyl phthalate (DBP) and di-2-ethylhexyl phthalate (DEHP) are two widely used phthalates, while Cu(II) is a common valence state of copper. They have been ubiquitously detected in the aquatic environment, but information on their joint toxicity to aquatic organisms is scarce. In this study, we evaluated the combined effects of copper and these two phthalates to Daphnia magna and Photobacterium phosphoreum by quantifying the acute toxicity expressed by the EC50 (the concentration causing 50 % of maximal effect) value. The toxicity order was DEHP + Cu(II) > DBP + Cu(II) > Cu(II) > DEHP > DBP for both test species. Antagonism effects were found in the joint toxicity of Cu(II) combined with DBP or DEHP using the toxic unit method. These findings have important implications in environmental risk assessment for phthalates in the aquatic environment in the presence of heavy metals.

  9. Experimental and theoretical investigations on temperature distribution at the joint interface for copper joints using ultrasonic welding

    Directory of Open Access Journals (Sweden)

    Elangovan Sooriya

    2014-01-01

    Full Text Available Ultrasonic welding is a solid-state joining process that produces joints by the application of high frequency vibratory energy in the work pieces held together under pressure without melting. Copper and its alloys are extensively used in electrical and electronic industry because of its excellent electrical and thermal properties. This paper mainly focused on temperature distribution and the influence of process parameters at the joint interface while joining copper sheets using ultrasonic welding process. Experiments are carried out using Cu sheets (0.2 mm and 0.3 mm thickness and the interface temperature is measured using Data Acquisition (DAQ System (thermocouple and thermal imager. Numerical and finite element based model for temperature distribution at the interface are developed and solved the same using Finite Difference Method (FDM and Finite Element Analysis (FEA. The results obtained from FDM and FEA model shows similar trend with experimental results and are found to be in good agreement.

  10. Characteristics of an optimized active metal cast joint between copper and C/C

    Energy Technology Data Exchange (ETDEWEB)

    Schedler, B [Technology Centre of PLANSEE SE, A-6600 Reutte (Austria); Huber, T [Technology Centre of PLANSEE SE, A-6600 Reutte (Austria); Friedrich, T [Technology Centre of PLANSEE SE, A-6600 Reutte (Austria); Eidenberger, E [Department of Physical Metallurgy and Materials Testing, Montanuniversitaet Leoben, A-8700 Leoben (Austria); Kapp, M [Austrian Academy of Sciences, Erich-Schmid-Institute of Material Science, A-8700 Leoben (Austria); Scheu, C [Department of Physical Metallurgy and Materials Testing, Montanuniversitaet Leoben, A-8700 Leoben (Austria); Pippan, R [Austrian Academy of Sciences, Erich-Schmid-Institute of Material Science, A-8700 Leoben (Austria); Clemens, H [Department of Physical Metallurgy and Materials Testing, Montanuniversitaet Leoben, A-8700 Leoben (Austria)

    2007-03-15

    In this paper, an optimized active metal cast copper to carbon composite (C/C) joint is examined. Mechanical characterization by means of shear and tensile tests as well as fracture toughness measurements at ambient temperature are employed, which show that the obtained values are above those of the reference joint that has been used so far. The phases occurring at the interface region and the fracture surface of the optimized joint are investigated in detail to explain the improved mechanical behaviour. The composition and the morphology at the interface region are analysed by means of scanning electron microscopy. In addition, the crack path is analysed by stereomicroscopy. The improved properties can be explained by the circumstance that the fracture of the optimized joint is not restricted to the interface between the occurring carbide and the C/C but changes between C/C, the carbide to C/C interface and the copper, depending on the local structure in the C/C composite.

  11. Joining of beryllium by braze welding technique: preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Banaim, P.; Abramov, E. [Ben-Gurion Univ. of the Negev, Beersheba (Israel); Zalkind, S.; Eden, S.

    1998-01-01

    Within the framework of some applications, there is a need to join beryllium parts to each other. Gas Tungsten Arc Braze Welds were made in beryllium using 0.3 mm commercially Aluminum (1100) shim preplaced at the joint. The welds exhibited a tendency to form microcracks in the Fusion Zone and Heat Affected Zone. All the microcracks were backfilled with Aluminum. (author)

  12. Single and joint toxicity of cypermethrin and copper on Chinese cabbage (Pakchoi) seeds.

    Science.gov (United States)

    Liu, T F; Wang, T; Sun, C; Wang, Y M

    2009-04-15

    The single and joint effects of Cu(2+) and cypermethrin (CPM) on the seed germination and the elongation of root and shoot of Pakchoi were investigated. The results showed that in solution low concentrations of Cu(2+) could accelerate the germination rate of Pakchoi, whereas high concentrations of Cu(2+) could inhibit it. CPM could strongly inhibit the germination of Pakchoi in solution. However, in the joint toxicity effect, CPM reduced the phytotoxicity of Cu(2+) on the germination of Pakchoi seeds under solution conditions. In the single-factor experiments and joint effect tests of CPM and copper on the seedling growth, it was found that there were significant liner relationships between concentrations of pollutants and root elongation (Psoil culture test, these synergistic effects were not significant (Pshoot elongation>germination rate.

  13. Beryllium chemistry and processing

    CERN Document Server

    Walsh, Kenneth A

    2009-01-01

    This book introduces beryllium; its history, its chemical, mechanical, and physical properties including nuclear properties. The 29 chapters include the mineralogy of beryllium and the preferred global sources of ore bodies. The identification and specifics of the industrial metallurgical processes used to form oxide from the ore and then metal from the oxide are thoroughly described. The special features of beryllium chemistry are introduced, including analytical chemical practices. Beryllium compounds of industrial interest are identified and discussed. Alloying, casting, powder processing, forming, metal removal, joining and other manufacturing processes are covered. The effect of composition and process on the mechanical and physical properties of beryllium alloys assists the reader in material selection. The physical metallurgy chapter brings conformity between chemical and physical metallurgical processing of beryllium, metal, alloys, and compounds. The environmental degradation of beryllium and its all...

  14. An industrial risk: Beryllium

    Directory of Open Access Journals (Sweden)

    Emrah Çaylak

    2012-03-01

    Full Text Available Beryllium is a vocational disease factor and berylliumexposure can potentially lead to Chronic Beryllium Disease(CBD in 2-6 % of workers. While acute lymphocyticpneumonia occurred in individuals who were exposedto high doses of beryllium, low dose exposure to berylliumfollowed by a long subclinical period can cause CBDcharacterized with chronic granulomatosis. It has beenobserved that varying amounts of beryllium exposureare necessary to produce symptoms of CBD or berylliumsensitization (BeS. Genetic differences between patientsmay be the underlying cause of these dose-effects andfurther study of the differences in patients exposed to berylliummay lead to earlier diagnosis and the identificationof biomarkers of CBD. In this review, it is summarizedthe general properties of beryllium exposure, the immunopathogenesisand genetic differences of beryllium-induceddiseases, genotoxicity and the carcinogenic effectsof beryllium. J Clin Exp Invest 2012; 3(1: 141-148

  15. Joint toxic action of binary metal mixtures of copper, manganese and nickel to Paronychiurus kimi (Collembola).

    Science.gov (United States)

    Son, Jino; Lee, Yun-Sik; Kim, Yongeun; Shin, Key-Il; Hyun, Seunghun; Cho, Kijong

    2016-10-01

    The joint toxic effects of binary metal mixtures of copper (Cu), manganese (Mn) and nickel (Ni) on reproduction of Paronhchiurus kimi (Lee) was evaluated using a toxic unit (TU) approach by judging additivity across a range of effect levels (10-90%). For all metal mixtures, the joint toxic effects of metal mixtures on reproduction of P. kimi decreased in a TU-dependent manner. The joint toxic effects of metal mixtures also changed from less than additive to more than additive at an effect level lower than or equal to 50%, while a more than additive toxic effects were apparent at higher effect levels. These results indicate that the joint toxicity of metal mixtures is substantially different from that of individual metals based on additivity. Moreover, the close relationship of toxicity to effect level suggests that it is necessary to encompass a whole range of effect levels rather than a specific effect level when judging mixture toxicity. In conclusion, the less than additive toxicity at low effect levels suggests that the additivity assumption is sufficiently conservative to warrant predicting joint toxicity of metal mixtures, which may give an additional margin of safety when setting soil quality standards for ecological risk assessment.

  16. Copper-to-silicon-carbide joints development for Future CLIC Hom Dampers

    CERN Document Server

    Gil Costa, Miguel

    2015-01-01

    Ceramic-to-metal joints have been of paramount importance for the nuclear and aeronautic industry since the last century. In this document, two different approaches to the Cu-to-SiC joining are briefly described and discussed. The first approach consists of an intermediate piece of lower Coefficient of Thermal Expansion than copper aiming to reduce the expansion mismatch with the ceramic during the brazing cycle. Soldering is selected as a second attempt, whose lower joining temperature reduces the absolute expansion difference between Cu and SiC. In addition, four SiC metallization processes are proposed and some of them have been also tested and discussed.

  17. (Beryllium). Internal Report No. 137, Jan. 15, 1958; Le beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Mouret, P.; Rigaud, A

    1959-07-01

    After a brief summary of the physical and chemical properties of beryllium, the various chemical treatments which can be applied to beryllium minerals either directly or after a physical enrichment are discussed. These various treatments give either the hydroxide or beryllium salts, from which either beryllium oxide or metallic beryllium can easily be obtained. The purification, analysis and uses of beryllium are also briefly discussed. (author)

  18. WETTING OF COPPER BY LEAD-FREE Sn-Cu SOLDERS AND SHEAR STRENGTH OF Cu – Cu JOINTS

    Directory of Open Access Journals (Sweden)

    Pavol Šebo

    2009-04-01

    Full Text Available Developing and microstructure of lead-free Sn-Cu solders containing 3, 5 and 10 wt. % of copper in bulk as well as in ribbon form is presented. Wetting of copper substrate by these solders at the temperatures 300, 350 and 400°C in air (partially in N2+10H2 during 1800 s was studied by sessile drop method. Joints Cu – solder – Cu were prepared at 300°C and 1800 s in air as well as in gas mix and their shear strength was measured. The microstructure was studied by light and scanning electron microscopy (SEM equipped with energy dispersive X-ray analyzer and standard X-ray diffraction machine. Wetting angle decreases with increasing wetting temperature. Wetting angle increased for higher (10 wt. % amount of copper in solder. Shear strength of the joints decreases with increasing the copper concentration in solder.

  19. Beryllium: genotoxicity and carcinogenicity.

    Science.gov (United States)

    Gordon, Terry; Bowser, Darlene

    2003-12-10

    Beryllium (Be) has physical-chemical properties, including low density and high tensile strength, which make it useful in the manufacture of products ranging from space shuttles to golf clubs. Despite its utility, a number of standard setting agencies have determined that beryllium is a carcinogen. Only a limited number of studies, however, have addressed the underlying mechanisms of the carcinogenicity and mutagenicity of beryllium. Importantly, mutation and chromosomal aberration assays have yielded somewhat contradictory results for beryllium compounds and whereas bacterial tests were largely negative, mammalian test systems showed evidence of beryllium-induced mutations, chromosomal aberrations, and cell transformation. Although inter-laboratory differences may play a role in the variability observed in genotoxicity assays, it is more likely that the different chemical forms of beryllium have a significant effect on mutagenicity and carcinogenicity. Because workers are predominantly exposed to airborne particles which are generated during the machining of beryllium metal, ceramics, or alloys, testing of the mechanisms of the mutagenic and carcinogenic activity of beryllium should be performed with relevant chemical forms of beryllium.

  20. Dissolution of beryllium in artificial lung alveolar macrophage phagolysosomal fluid.

    Science.gov (United States)

    Stefaniak, Aleksandr B; Virji, M Abbas; Day, Gregory A

    2011-05-01

    Dissolution of a lung burden of poorly soluble beryllium particles is hypothesized to be necessary for development of chronic beryllium lung disease (CBD) in humans. As such, particle dissolution rate must be sufficient to activate the lung immune response and dissolution lifetime sufficient to maintain chronic inflammation for months to years to support development of disease. The purpose of this research was to investigate the hypothesis that poorly soluble beryllium compounds release ions via dissolution in lung fluid. Dissolution kinetics of 17 poorly soluble particulate beryllium materials that span extraction through ceramics machining (ores, hydroxide, metal, copper-beryllium [CuBe] fume, oxides) and three CuBe alloy reference materials (chips, solid block) were measured over 31 d using artificial lung alveolar macrophage phagolysosomal fluid (pH 4.5). Differences in beryllium-containing particle physicochemical properties translated into differences in dissolution rates and lifetimes in artificial phagolysosomal fluid. Among all materials, dissolution rate constant values ranged from 10(-5) to 10(-10)gcm(-2)d(-1) and half-times ranged from tens to thousands of days. The presence of magnesium trisilicate in some beryllium oxide materials may have slowed dissolution rates. Materials associated with elevated prevalence of CBD had faster beryllium dissolution rates [10(-7)-10(-8)gcm(-2)d(-1)] than materials not associated with elevated prevalence (p<0.05).

  1. Beryllium Desorption from Sediments

    Science.gov (United States)

    Boschi, V.; Willenbring, J. K.

    2015-12-01

    Beryllium isotopes have provided a useful tool in the field of geochronology and geomorphology over the last 25 years. The amount of cosmogenic meteoric 10Be and native 9Be absorbed to soils often scales with the residence time and chemical weathering of sediments in a landscape, respectively. Thus, the concentrations in river sediment may be used to quantify the denudation of specific watersheds. When deposited in ocean sediment, these concentrations are thought to record the history of denudation on Earth over the last ~10 Ma. The use of both isotopes often relies on the premise of beryllium retention to sediment surfaces in order to preserve a landscape's erosion and weathering signature. Changes in setting, en route from the soil to fluvial system to the ocean, can cause beryllium desorption and may preclude some applications of the 10Be/9Be system. Four mechanisms were tested to determine the desorption potential of beryllium including a reduction in pH, an increase in ionic strength and complexation with soluble organic and inorganic species. These processes have the potential to mobilize beryllium into solution. For example, by both reducing the pH and increasing the ionic strength, competition for adsorption sites increases, potentially liberating beryllium from the sediment surface. In addition, organic and inorganic ligands can complex beryllium causing it to become mobilized. To determine which of these alterations influence beryllium desorption and to quantify the effect, we prepared separate solutions of beryllium bound to minerals and organic compounds and measured beryllium concentrations in solution before and after adjusting the pH, ionic strength, and changing inorganic and organic ligand concentrations. We conclude from our observations that overall, beryllium sorbed to organic compounds was more resistant to desorption relative to mineral-associated beryllium. Among the methods tested, a reduction in pH resulted in the greatest amount of

  2. Characterization and modeling of microstructural evolution of near-eutectic tin-silver-copper solder joints

    Science.gov (United States)

    Zbrzezny, Adam R.

    Near-eutectic Sn-Ag-Cu (SAC) solders are currently considered as major lead-free replacement candidates for Sn-Pb eutectic alloys in microelectronics applications. In this thesis, the microstructural thermal stability including recrystallization, grain growth behavior, Pb and Au contamination effects and interaction of the SAC solder with Cu and Ni substrates were investigated. The true eutectic composition of the Sn-Ag-Cu alloy was verified to be Sn3.5Ag0.9Cu wt.%, and the eutectic melting temperature was determined to be 217.4 +/- 0.8°C. The system was classified as belonging to faceting (Cu6Sn5)-faceting (Ag3Sn)-nonfaceting (Sn matrix) ternary eutectic. The most significant consequence of Pb contamination was the formation of a quaternary eutectic phase (Sn-Ag-Cu-Pb) with a melting point at 176°C. Similarly, the presence of gold in the SAC alloy led to a development of a new quaternary phase (Sn-Ag-Cu-Au) melting at 204°C. Prolonged aging of SAC-4 wt.% Au on nickel resulted in the deposition of a new, previously unreported, intermetallic (IMC) layer, ((Au1-xCUx)6Sn 5, 15 wt.% of Au) on top of the existing (Cu1-yNi y)6Sn5 layer. The interfacial products that formed during soldering to copper were Cu6Sn5 and Cu3Sn. Soldering to nickel resulted in the formation of one layer, (Cu1-yNiy) 6Sn5, which was different from the expected Ni3Sn 4 layer. A small copper content in the SAC solder (0.7 wt.%) was sufficient to promote this thermodynamic shift. Intermetallic growth on Cu during solid state aging was established to be bulk diffusion controlled. The IMC layers in the SAC system grew at a slower rate than in the Sn-Pb system. It was found that the reliability of SAC solder joints on copper was considerably better than on nickel due to copper enrichment during reflow and subsequent Cu6Sn5 intermetallic precipitation. Enhanced copper and silver diffusion followed by tin recrystallization and grain growth, cavity nucleation and subsequent micro-crack linkage formed

  3. Beryllium coating on Inconel tiles

    Energy Technology Data Exchange (ETDEWEB)

    Bailescu, V.; Burcea, G.; Lungu, C.P.; Mustata, I.; Lungu, A.M. [Association EURATOM-MEC Romania, National Institute of Laser, Plasma and Radiation Physics, Bucharest (Romania); Rubel, M. [Alfven Laboratory, Royal Institute of Technology, Stockholm (Sweden); Coad, J.P. [Culham Science Centre, EURATOM-UKAEA Fusion Association, Abingdon, OX, Oxon (United Kingdom); Matthews, G.; Pedrick, L.; Handley, R. [UKAEA Fusion, Association Euratom-UKAEA, Culham Science and Engineering Centre, OX 3DB ABINGDON, Oxon (United Kingdom)

    2007-07-01

    Full text of publication follows: The Joint European Torus (JET) is a large experimental nuclear fusion device. Its aim is to confine and study the behaviour of plasma in conditions and dimensions approaching those required for a fusion reactor. The plasma is created in the toroidal shaped vacuum vessel of the machine in which it is confined by magnetic fields. In preparation for ITER a new ITER-like Wall (ILW) will be installed on Joint European Torus (JET), a wall not having any carbon facing the plasma [1]. In places Inconel tiles are to be installed, these tiles shall be coated with Beryllium. MEdC represented by the National Institute for Laser, Plasma and Radiation Physics, Magurele, Bucharest and in direct cooperation with Nuclear Fuel Plant Pitesti started to coat Inconel tiles with 8 {mu}m of Beryllium in accordance with the requirements of technical specification and fit for installation in the JET machine. This contribution provides an overview of the principles of manufacturing processes using thermal evaporation method in vacuum and the properties of the prepared coatings. The optimization of the manufacturing process (layer thickness, structure and purity) has been carried out on Inconel substrates (polished and sand blasted) The results of the optimization process and analysis (SEM, TEM, XRD, Auger, RBS, AFM) of the coatings will be presented. Reference [1] Takeshi Hirai, H. Maier, M. Rubel, Ph. Mertens, R. Neu, O. Neubauer, E. Gauthier, J. Likonen, C. Lungu, G. Maddaluno, G. F. Matthews, R. Mitteau, G. Piazza, V. Philipps, B. Riccardi, C. Ruset, I. Uytdenhouwen, R and D on full tungsten divertor and beryllium wall for JET TIER-like Wall Project, 24. Symposium on Fusion Technology - 11-15 September 2006 -Warsaw, Poland. (authors)

  4. Microstructures and properties analysis of dissimilar metal joint in the friction stir welded copper to aluminum alloy

    Institute of Scientific and Technical Information of China (English)

    Wang Xijing; Zhang Zhongke; Da Chaobing; Li Jing

    2007-01-01

    This paper mainly concentrated on the feasibility of friction stir welding of dissimilar metal of aluminum alloy to copper (T2) and a preliminary analysis of welding parameters influencing on the microstructures and properties of joint was carried out. The results indicated that the thickness of workpiece played an important role in the welding parameters which could succeed in the friction stir welding of dissimilar metal of copper to aluminum alloy, and the parameters were proved to be a narrow choice. The interfacial region between copper and aluminum in the dissimilar joint was not uniformly mixed, constituted with part of incomplete mixing zone, complete mixing zone, dispersion zone and the most region's boundary was obvious. Meantime a kind banded structure with inhomogeneous width was formed. The intermetallic compounds generated during friction stir welding in the interfacial region were mainly Cu9Al4 , Al2Cu etc, and their hardness was higher than others.

  5. Interface structure and mechanical property of the brazed joint of graphite and copper

    Institute of Scientific and Technical Information of China (English)

    XIE Fengchun; ZHANG Lixia; FENG Jicai; HE Peng

    2009-01-01

    A kind of self-made AgCuTiSn braze alloy powder was used to join graphite and copper. The whole brazing process was performed under vacuum circumstances at different temperatures (1033-1193 K) for several holding time (300-1800 s). According to scanning electron microscope (SEM), energy dispersive spectrometer (EDS) and electron probe X-ray microanalysis (EPMA) results, the reaction products of the interface are TiC, Ti3Sn, Cu(s. s), Ag(s. s) and Cu-Sn compound. As the brazing parameters increase, the quantity of Ag(s. s) in the braze alloy and C fibers on graphite/AgCuTiSn interface reduce, while that of Cu (s. s) in the braze alloy improves. When the brazing temperature is 1093 K and holding time is 900 s, the joint can obtain the maximum room temperature shear strength 24 MPa.

  6. Cooperativity in beryllium bonds.

    Science.gov (United States)

    Alkorta, Ibon; Elguero, José; Yáñez, Manuel; Mó, Otilia

    2014-03-07

    A theoretical study of the beryllium bonded clusters of the (iminomethyl)beryllium hydride and (iminomethyl)beryllium fluoride [HC(BeX)=NH, X = H, F] molecules has been carried out at the B3LYP/6-311++G(3df,2p) level of theory. Linear and cyclic clusters have been characterized up to the decamer. The geometric, energetic, electronic and NMR properties of the clusters clearly indicate positive cooperativity. The evolution of the molecular properties, as the size of the cluster increases, is similar to those reported in polymers held together by hydrogen bonds.

  7. Selection of I-220H beryllium for NIRCam optical bench

    Science.gov (United States)

    Edinger, Derek J.; Nordt, Alison A.

    2005-08-01

    The Near Infrared Camera (NIRCam) for NASA's James Webb Space Telescope (JWST) is one of the four science instruments to be installed into the Integrated Science Instrument Module (ISIM) on JWST. I-220H beryllium was chosen as the optical bench material for NIRCam based on its high specific stiffness, relatively high thermal conductivity, low CTE at cryogenic temperatures, and overall thermal stability at cryogenic temperatures. Beryllium has cryogenic heritage, but development of a structural bonded joint that could survive cryogenic temperatures was required. This paper will describe the trade studies performed in which bonded, I-220H beryllium was selected.

  8. Beryllium Manufacturing Processes

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, A

    2006-06-30

    This report is one of a number of reports that will be combined into a handbook on beryllium. Each report covers a specific topic. To-date, the following reports have been published: (1) Consolidation and Grades of Beryllium; (2) Mechanical Properties of Beryllium and the Factors Affecting these Properties; (3) Corrosion and Corrosion Protection of Beryllium; (4) Joining of Beryllium; (5) Atomic, Crystal, Elastic, Thermal, Nuclear, and other Properties of Beryllium; and (6) Beryllium Coating (Deposition) Processes and the Influence of Processing Parameters on Properties and Microstructure. The conventional method of using ingot-cast material is unsuitable for manufacturing a beryllium product. Beryllium is a highly reactive metal with a high melting point, making it susceptible to react with mold-wall materials forming beryllium compounds (BeO, etc.) that become entrapped in the solidified metal. In addition, the grain size is excessively large, being 50 to 100 {micro}m in diameter, while grain sizes of 15 {micro}m or less are required to meet acceptable strength and ductility requirements. Attempts at refining the as-cast-grain size have been unsuccessful. Because of the large grain size and limited slip systems, the casting will invariably crack during a hot-working step, which is an important step in the microstructural-refining process. The high reactivity of beryllium together with its high viscosity (even with substantial superheat) also makes it an unsuitable candidate for precision casting. In order to overcome these problems, alternative methods have been developed for the manufacturing of beryllium. The vast majority of these methods involve the use of beryllium powders. The powders are consolidated under pressure in vacuum at an elevated temperature to produce vacuum hot-pressed (VHP) blocks and vacuum hot-isostatic-pressed (HIP) forms and billets. The blocks (typically cylindrical), which are produced over a wide range of sizes (up to 183 cm dia. by 61

  9. Ultrasonic test of carbon composite/copper joints in the ITER divertor

    Energy Technology Data Exchange (ETDEWEB)

    Roccella, S., E-mail: selanna.roccella@enea.it [Associazione ENEA-Euratom sulla Fusione, C.R. Frascati, 00044 Frascati, RM (Italy); Cacciotti, E. [Associazione ENEA-Euratom sulla Fusione, C.R. Frascati, 00044 Frascati, RM (Italy); Candura, D. [Ansaldo Nucleare S.p.A., C. so F.M. Perrone 25, 16152 Genoa (Italy); Mancini, A.; Pizzuto, A.; Reale, A. [Associazione ENEA-Euratom sulla Fusione, C.R. Frascati, 00044 Frascati, RM (Italy); Tatì, A. [Associazione Euratom-ENEA sulla Fusione, C.R. Casaccia, Via Anguillarese 301, 00123 Santa Maria di Galeria, RM (Italy); Visca, E. [Associazione ENEA-Euratom sulla Fusione, C.R. Frascati, 00044 Frascati, RM (Italy)

    2013-10-15

    Highlights: • ENEA developed and tested a specimen for the simulation of defects at the interface between CFC and copper. • The use of an ultrasonic technique properly set permitted to highlight and size with high accuracy the defects. • The technology developed could be employed successfully in the production of these components for high heat flux applications. -- Abstract: The vertical targets of the ITER divertor consist of high flux units (HFU) actively cooled: CuCrZr tubes armoured by tungsten and carbon/carbon fibre composite (CFC). The armour is obtained with holed parallelepiped blocks, called monoblocks, previously prepared and welded onto the tubes by means diffusion bonding. The monoblock preparation consists in the casting of a layer of copper oxygen free (Cu OFHC) inside the monoblock hole. Each HFU is covered with more than 100 monoblocks that have to be joined simultaneously to the tube. Therefore, it is very important to individuate any defects present in the casting of Cu OFHC or at the interface with the CFC before the monoblocks are installed on the units. This paper discusses the application of non-destructive testing by ultrasound (US) method for the control of the joining interfaces between CFC monoblocks and Cu OFHC, before the brazing on the CrCrZr tube. In ENEA laboratory an ultrasonic technique (UT) suitable for the control of these joints with size and geometry according to the ITER specifications has been developed and widely tested. Real defects in this type of joints are, however, still hardly detected by UT. The CFC surface has to be machined to improve the mechanical strength of the joint. This results in a surface not perpendicular to the ultrasonic wave. Moreover, CFC is characterized by high acoustic attenuation of the ultrasonic wave and then it is not easy to get information regarding the Cu/CFC bonding. Nevertheless, the UT sharpness and simplicity pushes to perform some further study. With this purpose, a sample with

  10. Beryllium coating produced by evaporation-condensation method and some their properties

    Energy Technology Data Exchange (ETDEWEB)

    Pepekin, G.I.; Anisimov, A.B.; Chernikov, A.S.; Mozherinn, S.I.; Pirogov, A.A. [SRI SIA Lutch., Podolsk (Russian Federation)

    1998-01-01

    The method of vacuum evaporation-condensation for deposition of beryllium coatings on metal substrates, considered in the paper, side by side with a plasma-spray method is attractive fon ITER application. In particular this technique may be useful for repair the surface of eroded tiles which is operated in a strong magnetic field. The possibility of deposition of beryllium coatings with the rate of layer growth 0.1-0.2 mm/h is shown. The compatibility of beryllium coating with copper or stainless steel substrate is provided due to intermediate barrier. The results of examination of microstructure, microhardness, porosity, thermal and physical properties and stability under thermal cycling of beryllium materials are presented. The value of thermal expansion coefficient and thermal conductivity of condensed beryllium are approximately the same as for industrial grade material produced by powder mettalurgy technique. However, the condensed beryllium has higher purity (up to 99.9-99.99 % wt.). (author)

  11. Improving adhesion of copper/epoxy joints by pulsed laser ablation

    KAUST Repository

    Hernandez, Edwin

    2015-10-19

    The purpose of the present work is to analyze the effect of pulsed laser ablation on copper substrates (CuZn40) deployed for adhesive bonding. Surface pre-treatment was carried using an Yb-fiber laser beam. Treated surfaces were probed using Scanning Electron Microscopy (SEM) and X-Ray Photoelectron Spectroscopy (XPS). The mechanical performance of CuZn40/epoxy bonded joints was assessed using the T-peel test coupon. In order to resolve the mechanisms of failure and adhesive penetration within surface asperities induced by the laser treatment, fracture surfaces were surveyed using SEM. Finite element simulations, based on the use of the cohesive zone model of fracture, were carried out to evaluate the variation of bond toughness. Results indicated that the laser ablation process effectively modifies surface morphology and chemistry and enables enhanced mechanical interlocking and cohesive failure within the adhesive layer. Remarkable improvements of apparent peel energy and bond toughness were observed with respect to control samples with sanded substrates.

  12. Achieving High Strength Joint of Pure Copper Via Laser-Cold Metal Transfer Arc Hybrid Welding

    Science.gov (United States)

    Chen, Yulong; Chen, Cong; Gao, Ming; Zeng, Xiaoyan

    2016-06-01

    Fiber laser-cold metal transfer arc hybrid welding of pure copper was studied. Weld porosity was tested by X-ray nondestructive testing. Microstructure and fracture features were observed by scanning electron microscopy. Mechanical properties were evaluated by cross weld tensile test. Full penetrated and continuous welds were obtained by hybrid welding once the laser power reached 2 kW, while they could not be obtained by laser welding alone, even though the laser power reached 5 kW. The ultimate tensile strength (UTS), the yield strength (YS), and the elongation of the best hybrid weld material were up to 227, 201 MPa, and 21.5 pct, respectively. The joint efficiencies in UTS and YS of hybrid weld were up to 84 and 80 pct of the BM, respectively. The fracture location changes from the fusion zone to the heat-affected zone with the increase of laser power. Besides, the mechanisms of process stability and porosity suppression were clarified by laser-arc interaction and pool behavior. The strengthening mechanism was discussed by microstructure characteristics.

  13. Determination of beryllium by using X-ray fluorescence spectrometry.

    Science.gov (United States)

    Zawisza, Beata

    2008-03-01

    X-ray fluorescence spectrometry method is subject to certain difficulties and inconveniences for the elements having the atomic number 9 or less. These difficulties become progressively more severe as the atomic number decreases, and are quite serious for beryllium, which is practically indeterminable directly by XRF. Therefore, an indirect determination of beryllium that is based on the evaluation of cobalt in the precipitate is taken into consideration. In the thesis below, there is a description of a new, simple, and precise method by selective precipitation using hexamminecobalt(III) chloride and ammonium carbonate-EDTA solution as a complexing agent for the determining of a trace amount of beryllium using X-ray fluorescence spectrometry. The optimum conditions for [Co(NH(3))(6)][Be(2)(OH)(3)(CO(3))(2)(H(2)O)(2)].(3)H(2)O complex formation were studied. The complex was collected on the membrane filter, and the Co Kalpha line was measured by XRF. The method presents the advantages of the sample preparation and the elimination of the matrix effects due to the thin film obtained. The detection limit of the proposed method is 0.2 mg of beryllium. The method was successfully applied to beryllium determination in copper/ beryllium/cobalt alloys.

  14. Beryllium contamination and exposure monitoring in an inhalation laboratory setting.

    Science.gov (United States)

    Muller, Caroline; Audusseau, Séverine; Salehi, Fariba; Truchon, Ginette; Chevalier, Gaston; Mazer, Bruce; Kennedy, Greg; Zayed, Joseph

    2010-02-01

    Beryllium (Be) is used in several forms: pure metal, beryllium oxide, and as an alloy with copper, aluminum, or nickel. Beryllium oxide, beryllium metal, and beryllium alloys are the main forms present in the workplace, with inhalation being the primary route of exposure. Cases of workers with sensitization or chronic beryllium disease challenge the scientific community for a better understanding of Be toxicity. Therefore, a toxicological inhalation study using a murine model was performed in our laboratory in order to identify the toxic effects related to different particle sizes and chemical forms of Be. This article attempts to provide information regarding the relative effectiveness of the environmental monitoring and exposure protection program that was enacted to protect staff (students and researchers) in this controlled animal beryllium inhalation exposure experiment. This includes specific attention to particle migration control through intensive housekeeping and systematic airborne and surface monitoring. Results show that the protective measures applied during this research have been effective. The highest airborne Be concentration in the laboratory was less than one-tenth of the Quebec OEL (occupational exposure limit) of 0.15 microg/m(3). Considering the protection factor of 10(3) of the powered air-purifying respirator used in this research, the average exposure level would be 0.03 x 10(- 4) microg/m(3), which is extremely low. Moreover, with the exception of one value, all average Be concentrations on surfaces were below the Quebec Standard guideline level of 3 microg/100 cm(2) for Be contamination. Finally, all beryllium lymphocyte proliferation tests for the staff were not higher than controls.

  15. Microstructure and mechanical properties of similar and dissimilar joints of aluminium alloy and pure copper by friction stir welding

    Directory of Open Access Journals (Sweden)

    V.C. Sinha

    2016-09-01

    Full Text Available In the present study, the microstructure and mechanical properties of similar and dissimilar friction stir welded joints of aluminium alloy (AlA and pure copper (Cu were evaluated at variable tool rotational speeds from 150 to 900 rpm in steps of 150 rpm at 60 mm/min travel speed and constant tilt angle 2°. The interfacial microstructures of the joints were characterised by optical and scanning electron microscopy. The Al4Cu9, AlCu, Al2Cu and Al2Cu3 intermetallic compounds have been observed at the interface and stir zone region of dissimilar Al/Cu FSWed joints. Variation in the grain size was observed in the stir zone depending upon the heat input value. Axial force, traverse force and torque value were analysed with variation in tool rotational speed. Residual stresses were measured at the stir zone by X-ray diffraction technique. Maximum ultimate tensile strength of ∼75% of AlA strength for AlA–AlA joints has been obtained at 750 rpm and for Cu–Cu joint tensile strength of ∼100% of tensile strength of Cu was obtained at 300 rpm. However, for Cu–AlA joint when processed at 600 rpm tool rotational speed achieved maximum ultimate tensile strength of ∼77% of AlA.

  16. Numerical investigation of the joint impact of thermophoresis and radiative losses in induction plasma synthesis of copper nanoparticles

    Science.gov (United States)

    Bianconi, S.; Boselli, M.; Gherardi, M.; Colombo, V.

    2017-04-01

    A numerical model for the simulation of the copper nanoparticles synthesis process by an induction thermal plasma system has been developed, taking into account the joint effects of radiative losses from the metallic vapour and thermophoretic transport of the synthetized nanoparticles on the process performance; the final aim of the work is that of setting up an accurate modelling tool for design-oriented simulation and optimization of the synthesis process. Radiative losses from copper vapour and thermophoresis have been taken into account for different reaction chamber geometries (a cylindrical one and one with a conical top section) combined with different quench gas injection strategies and different power levels, in order to evaluate the impact of these phenomena in process design strategies. The numerical results show that both these phenomena have a relevant impact on the process parameters for all the investigated cases, and that they should be taken into account in order to develop increasingly accurate models for process design and optimization.

  17. Joint toxicity of tetracycline with copper(II) and cadmium(II) to Vibrio fischeri: effect of complexation reaction.

    Science.gov (United States)

    Tong, Fei; Zhao, Yanping; Gu, Xueyuan; Gu, Cheng; Lee, Charles C C

    2015-03-01

    Co-contamination of antibiotic and heavy metals commonly occurs in the environment. Tetracycline (TC), a common antibiotic, can behave as an efficient organic ligand to complex with cations. In this paper, the joint toxicity of TC with two commonly existing metals, copper(II) and cadmium(II), towards a luminescent bacteria, Vibrio fischeri, are investigated. Results showed that coexistence of TC and Cu(II) showed a significant antagonistic effect, while TC and Cd(II) showed a synergistic effect. The aqueous speciation of TC with two metal cations was calculated using a chemical equilibrium software Visual MINTEQ and results indicated that a strong complexation exist between TC and Cu(II), while much weaker interaction between TC and Cd(II). Traditional joint toxicity prediction model based on independent action failed to predict the combined toxicity of TC with metals. A new method based on speciation calculation was used to evaluate the joint toxicity of ligands and cations. It is assumed that the metal-ligand complexes are non-toxic to V. fischeri and the joint toxicity is determined by the sum of toxic unit of free metal-ions and free organic ligands. It explained the joint toxicity of the mixed systems reasonably well. Meanwhile, citric acid (CA) and fulvic acid (FA) were also introduced in this study to provide a benchmark comparison with TC. Results showed it is also valid for mixed systems of CA and FA with metals except for the Cd-CA mixture.

  18. Reprocessing technology development for irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, H.; Sakamoto, N. [Oarai Research Establishment, Ibaraki-ken (Japan); Tatenuma, K. [KAKEN Co., Ibaraki-ken (Japan)] [and others

    1995-09-01

    At present, beryllium is under consideration as a main candidate material for neutron multiplier and plasma facing material in a fusion reactor. Therefore, it is necessary to develop the beryllium reprocessing technology for effective resource use. And, we have proposed reprocessing technology development on irradiated beryllium used in a fusion reactor. The preliminary reprocessing tests were performed using un-irradiated and irradiated beryllium. At first, we performed beryllium separation tests using un-irradiated beryllium specimens. Un-irradiated beryllium with beryllium oxide which is a main impurity and some other impurities were heat-treated under chlorine gas flow diluted with Ar gas. As the results high purity beryllium chloride was obtained in high yield. And it appeared that beryllium oxide and some other impurities were removed as the unreactive matter, and the other chloride impurities were separated by the difference of sublimation temperature on beryllium chloride. Next, we performed some kinds of beryllium purification tests from beryllium chloride. And, metallic beryllium could be recovered from beryllium chloride by the reduction with dry process. In addition, as the results of separation and purification tests using irradiated beryllium specimens, it appeared that separation efficiency of Co-60 from beryllium was above 96%. It is considered that about 4% Co-60 was carried from irradiated beryllium specimen in the form of cobalt chloride. And removal efficiency of tritium from irradiated beryllium was above 95%.

  19. Aerosols generated during beryllium machining.

    Science.gov (United States)

    Martyny, J W; Hoover, M D; Mroz, M M; Ellis, K; Maier, L A; Sheff, K L; Newman, L S

    2000-01-01

    Some beryllium processes, especially machining, are associated with an increased risk of beryllium sensitization and disease. Little is known about exposure characteristics contributing to risk, such as particle size. This study examined the characteristics of beryllium machining exposures under actual working conditions. Stationary samples, using eight-stage Lovelace Multijet Cascade Impactors, were taken at the process point of operation and at the closest point that the worker would routinely approach. Paired samples were collected at the operator's breathing zone by using a Marple Personal Cascade Impactor and a 35-mm closed-faced cassette. More than 50% of the beryllium machining particles in the breathing zone were less than 10 microns in aerodynamic diameter. This small particle size may result in beryllium deposition into the deepest portion of the lung and may explain elevated rates of sensitization among beryllium machinists.

  20. T cell recognition of beryllium.

    Science.gov (United States)

    Dai, Shaodong; Falta, Michael T; Bowerman, Natalie A; McKee, Amy S; Fontenot, Andrew P

    2013-12-01

    Chronic beryllium disease (CBD) is a granulomatous lung disorder caused by a hypersensitivity to beryllium and characterized by the accumulation of beryllium-specific CD4(+) T cells in the lung. Genetic susceptibility to beryllium-induced disease is strongly associated with HLA-DP alleles possessing a glutamic acid at the 69th position of the β-chain (βGlu69). The structure of HLA-DP2, the most prevalent βGlu69-containing molecule, revealed a unique solvent-exposed acidic pocket that includes βGlu69 and represents the putative beryllium-binding site. The delineation of mimotopes and endogenous self-peptides that complete the αβTCR ligand for beryllium-specific CD4(+) T cells suggests a unique role of these peptides in metal ion coordination and the generation of altered self-peptides, blurring the distinction between hypersensitivity and autoimmunity.

  1. The Effect of Welding Energy on the Microstructural and Mechanical Properties of Ultrasonic-Welded Copper Joints

    Directory of Open Access Journals (Sweden)

    Jingwei Yang

    2017-02-01

    Full Text Available The effects of welding energy on the mechanical and microstructural characteristics of ultrasonic-welded pure copper plates were investigated. Complex dynamic recrystallization and grain growth occurred inside the weld zone during ultrasonic welding. At a low welding energy, a thin band of straight weld interfaces was observed and had an ultra-fine grain structure. With an increase in welding energy, the weld interface progressively changed from flat to sinusoidal, and eventually turned into a convoluted wavy pattern, bearing similarities to shear instabilities, as observed in fluid dynamics. The lap shear load of the joints initially increased and then remained stable as the welding energy increased. The tensile characteristics of the joints significantly depended on the development of plastic deformation at the interface. The influence of the microstructure on the hardness was also discussed.

  2. Characterization of shocked beryllium

    Directory of Open Access Journals (Sweden)

    Papin P.A.

    2012-08-01

    Full Text Available While numerous studies have investigated the low-strain-rate constitutive response of beryllium, the combined influence of high strain rate and temperature on the mechanical behavior and microstructure of beryllium has received limited attention over the last 40 years. In the current work, high strain rate tests were conducted using both explosive drive and a gas gun to accelerate the material. Prior studies have focused on tensile loading behavior, or limited conditions of dynamic strain rate and/or temperature. Two constitutive strength (plasticity models, the Preston-Tonks-Wallace (PTW and Mechanical Threshold Stress (MTS models, were calibrated using common quasi-static and Hopkinson bar data. However, simulations with the two models give noticeably different results when compared with the measured experimental wave profiles. The experimental results indicate that, even if fractured by the initial shock loading, the Be remains sufficiently intact to support a shear stress following partial release and subsequent shock re-loading. Additional “arrested” drive shots were designed and tested to minimize the reflected tensile pulse in the sample. These tests were done to both validate the model and to put large shock induced compressive loads into the beryllium sample.

  3. 40 CFR 468.10 - Applicability; description of the copper forming subcategory.

    Science.gov (United States)

    2010-07-01

    ... treatment works from the forming of copper and copper alloys except beryllium copper alloys. ... copper forming subcategory. 468.10 Section 468.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS COPPER FORMING POINT SOURCE CATEGORY Copper...

  4. Characterization of Shocked Beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Cady, Carl M [Los Alamos National Laboratory; Adams, Chris D [Los Alamos National Laboratory; Hull, Lawrence M [Los Alamos National Laboratory; Gray III, George T [Los Alamos National Laboratory; Prime, Michael B [Los Alamos National Laboratory; Addessio, Francis L [Los Alamos National Laboratory; Wynn, Thomas A [Los Alamos National Laboratory; Brown, Eric N [Los Alamos National Laboratory

    2012-08-24

    Beryllium metal has many excellent structural properties in addition to its unique radiation characteristics, including: high elastic modulus, low Poisson's ratio, low density, and high melting point. However, it suffers from several major mechanical drawbacks: 1) high anisotropy - due to its hexagonal lattice structure and its susceptibility to crystallographic texturing; 2) susceptibility to impurity-induced fracture - due to grain boundary segregation; and 3) low intrinsic ductility at ambient temperatures thereby limiting fabricability. While large ductility results from deformation under the conditions of compression, the material can exhibit a brittle behavior under tension. Furthermore, there is a brittle to ductile transition at approximately 200 C under tensile conditions. While numerous studies have investigated the low-strain-rate constitutive response of beryllium, the combined influence of high strain rate and temperature on the mechanical behavior and microstructure of beryllium has received limited attention over the last 40 years. Prior studies have focused on tensile loading behavior, or limited conditions of dynamic strain rate and/or temperature. The beryllium used in this study was Grade S200-F (Brush Wellman, Inc., Elmore, OH) material. The work focused on high strain rate deformation and examine the validity of constitutive models in deformation rate regimes, including shock, the experiments were modeled using a Lagrangian hydrocode. Two constitutive strength (plasticity) models, the Preston-Tonks-Wallace (PTW) and Mechanical Threshold Stress (MTS) models, were calibrated using the same set of quasi-static and Hopkinson bar data taken at temperatures from 77K to 873K and strain rates from 0.001/sec to 4300/sec. In spite of being calibrated on the same data, the two models give noticeably different results when compared with the measured wave profiles. These high strain rate tests were conducted using both explosive drive and a gas gun to

  5. Effects of Phenolic Resin Addition on the Electrical Conductivity and Mechanical Strength of Nano-Copper Paste Formed Cu-Cu Joints

    Science.gov (United States)

    Gao, Runhua; Shen, Jun; Xie, Fuxing; Zuo, Yang; Wu, Dong

    2017-07-01

    Cu-Cu joints bonded by nano-copper pastes with different amounts of phenolic resin were developed at a low temperature (240°C) and a low pressure (1 MPa). The shear strengths of the joints were measured and the bonding layers were observed by scanning electron microscopy. The electrical conductivity of the joints was tested by a parameter analyzer. The results indicated that 2% phenolic resin in the pastes doubled the shear strength of Cu-Cu joints compared to joints made with 0%, 5% and 8% phenolic, because it filled the voids and coated sintered Cu nanoparticles in the joints without affecting the electrical conductivity of the Cu-Cu joint. This was because 2% phenolic paste prevented Cu nanoparticles from oxidation. However, 8% phenolic resin led to an increase of electrical resistivity due to the insulating property of phenolic resin, and a decrease of shear strength due to the hindrance to sintering between the nanoparticles.

  6. The development and advantages of beryllium capsules for the National Ignition Facility

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, D.C.; Bradley, P.A.; Hoffman, N.M. [Los Alamos National Lab., NM (United States)] [and others

    1998-02-01

    Capsules with beryllium ablators have long been considered as alternatives to plastic for the National Ignition Facility laser ; now the superior performance of beryllium is becoming well substantiated. Beryllium capsules have the advantages of relative insensitivity to instability growth, low opacity, high tensile strength, and high thermal conductivity. 3-D calculation with the HYDRA code NTIS Document No. DE-96004569 (M. M. Marinak et.al. in UCRL-LR-105821-95-3) confirm 2-D LASNEX U. B. Zimmerman and W. L. Kruer, Comments Plasmas Phys. Controlled Thermonucl. Fusion, 2, 51(2975) results that particular beryllium capsule designs are several times less sensitive than the CH point design to instability growth from DT ice roughness. These capsule designs contain more ablator mass and leave some beryllium unablated at ignition. By adjusting the level of copper dopant, the unablated mass can increase or decrease, with a corresponding decrease or increase in sensitivity to perturbations. A plastic capsule with the same ablator mass as the beryllium and leaving the same unablated mass also shows this reduced perturbation sensitivity. Beryllium`s low opacity permits the creation of 250 eV capsule designs. Its high tensile strength allows it to contain DT fuel at room temperature. Its high thermal conductivity simplifies cryogenic fielding.

  7. Technical Basis for PNNL Beryllium Inventory

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Michelle Lynn

    2014-07-09

    The Department of Energy (DOE) issued Title 10 of the Code of Federal Regulations Part 850, “Chronic Beryllium Disease Prevention Program” (the Beryllium Rule) in 1999 and required full compliance by no later than January 7, 2002. The Beryllium Rule requires the development of a baseline beryllium inventory of the locations of beryllium operations and other locations of potential beryllium contamination at DOE facilities. The baseline beryllium inventory is also required to identify workers exposed or potentially exposed to beryllium at those locations. Prior to DOE issuing 10 CFR 850, Pacific Northwest Nuclear Laboratory (PNNL) had documented the beryllium characterization and worker exposure potential for multiple facilities in compliance with DOE’s 1997 Notice 440.1, “Interim Chronic Beryllium Disease.” After DOE’s issuance of 10 CFR 850, PNNL developed an implementation plan to be compliant by 2002. In 2014, an internal self-assessment (ITS #E-00748) of PNNL’s Chronic Beryllium Disease Prevention Program (CBDPP) identified several deficiencies. One deficiency is that the technical basis for establishing the baseline beryllium inventory when the Beryllium Rule was implemented was either not documented or not retrievable. In addition, the beryllium inventory itself had not been adequately documented and maintained since PNNL established its own CBDPP, separate from Hanford Site’s program. This document reconstructs PNNL’s baseline beryllium inventory as it would have existed when it achieved compliance with the Beryllium Rule in 2001 and provides the technical basis for the baseline beryllium inventory.

  8. Thermal fatigue of beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Deksnis, E.; Ciric, D.; Falter, H. [JET Joint undertaking, Abingdon (United Kingdom)] [and others

    1995-09-01

    Thermal fatigue life of S65c beryllium castellated to a geometry 6 x 6 x (8-10)mm deep has been tested for steady heat fluxes of 3 MW/m{sup 2} to 5 MW/m{sup 2} and under pulsed heat fluxes (10-20 MW/m{sup 2}) for which the time averaged heat flux is 5 MW/m{sup 2}. These tests were carried out in the JET neutral beam test facility A test sequence with peak surface temperatures {le} 600{degrees}C produced no visible fatigue cracks. In the second series of tests, with T{sub max} {le} 750{degrees}C evidence for fatigue appeared after a minimum of 1350 stress cycles. These fatigue data are discussed in view of the observed lack of thermal fatigue in JET plasma operations with beryllium PFC. JET experience with S65b and S65c is reviewed; recent operations with {Phi} = 25 MW/m{sup 2} and sustained melting/resolidification are also presented. The need for a failure criterion for finite element analyses of Be PFC lifetimes is discussed.

  9. Infrared spectroscopy of copper-resveratrol complexes: A joint experimental and theoretical study

    Energy Technology Data Exchange (ETDEWEB)

    Chiavarino, B.; Crestoni, M. E.; Fornarini, S. [Dipartimento di Chimica e Tecnologie del Farmaco, Sapienza - Universita di Roma, Piazzale A. Moro 5, 00185 Rome (Italy); Taioli, S. [Interdisciplinary Laboratory for Computational Science, FBK-CMM and University of Trento, Via Sommarive 18, 38123 Trento (Italy); Department of Physics, University of Trento, Via Sommarive 14, 38123 Trento (Italy); Istituto Nazionale di Fisica Nucleare, Sezione di Perugia (Italy); Department of Chemistry, University of Bologna, Via F. Selmi 2, I-40126 Bologna (Italy); Mancini, I.; Tosi, P. [Department of Physics, University of Trento, Via Sommarive 14, 38123 Trento (Italy)

    2012-07-14

    Infrared multiple-photon dissociation spectroscopy has been used to record vibrational spectra of charged copper-resveratrol complexes in the 3500-3700 cm{sup -1} and 1100-1900 cm{sup -1} regions. Minimum energy structures have been determined by density functional theory calculations using plane waves and pseudopotentials. In particular, the copper(I)-resveratrol complex presents a tetra-coordinated metal bound with two carbon atoms of the alkenyl moiety and two closest carbons of the adjoining resorcinol ring. For these geometries vibrational spectra have been calculated by using linear response theory. The good agreement between experimental and calculated IR spectra for the selected species confirms the overall reliability of the proposed geometries.

  10. Beryllium in the ITER blanket

    Energy Technology Data Exchange (ETDEWEB)

    Billone, M.C.

    1995-01-01

    This paper consists of viewgraphs used in a presentation on the application of beryllium in breeding blankets for ITER and JET. The paper brings together data on the physical, thermal, mechanical, and chemical properties of beryllium and beryllium oxide for this type of application, as well as issues of compatibility with construction materials, and irradiation experience. It includes the results from testing programs carried out to arrive at some of the information, including fabrication work, irradiation experiments, and sample tests performed both in and out of the irradiation piles.

  11. Fluorometric determination of beryllium with 2-(o-hydroxylphenyl)benzoxazole

    Energy Technology Data Exchange (ETDEWEB)

    Gladilovich, D.B.; Stolyarov, K.P.

    1985-09-01

    According to the authors, of great interest for the fluorometric determination of small quantities of beryllium is 2-(o-hydroxyphenyl)benzthiazole (HPBT). In this work, 2-(o-hydroxyphenyl)benzoaxzole (HPBO), which is an analog of HPBT and differs from it in that the sulfur atom in the heterocyclic portion of the molecule is replaced by an oxygen atom, is proposed as a reagent for the fluorometric determination of beryllium. The fluorescent reaction of HPBO with beryllium is studied in this paper, in addition to the selection of the optimum conditions for the determination and the development of a procedure for the analysis of complex objects on this basis. The reaction proceeds in aqueous ethanol medium at pH 7.2-7.5. The limit of detection is 0.6 ng/ml. Methods have been developed for the determination of 10/sup -2/% beryllium in alloys based on copper and 10/sup -3/-10/sup -4/% in standard samples of silicate rocks.

  12. Acid-base jointly promoted copper(I)-catalyzed azide-alkyne cycloaddition.

    Science.gov (United States)

    Shao, Changwei; Wang, Xinyan; Zhang, Qun; Luo, Sheng; Zhao, Jichen; Hu, Yuefei

    2011-08-19

    In this novel acid-base jointly promoted CuAAC, the combination of CuI/DIPEA/HOAc was developed as a highly efficient catalytic system. The functions of DIPEA and HOAc have been assigned, and HOAc was recognized to accelerate the conversions of the C-Cu bond-containing intermediates and buffer the basicity of DIPEA. As a result, all drawbacks occurring in the popular catalytic system CuI/NR(3) were overcome easily.

  13. Reduction of liquid metal embrittlement in copper-brazed stainless steel joints

    Science.gov (United States)

    Uhlig, T.; Fedorov, V.; Elßner, M.; Wagner, G.; Weis, S.

    2017-03-01

    Due to its very good formability and the low raw material cost, pure copper in form of foils is commonly used to braze plate heat exchangers made of stainless steel. The difference in the electrochemical potentials of brazing filler and base material leads to corrosion effects in contact with electrolytes. This may lead to leakages, which decrease the reliability of the heat exchanger during service in potable water. The dissolution of the emerging corrosion products of brazing filler and base material induces the migration of heavy metal ions, such as Cu2+ and Ni2+, into the potable water. The so-called liquid metal embrittlement, which takes place during the brazing process, may intensify the corrosion. The brazing filler infiltrates the stainless steel along the grain boundaries and causes an embrittlement. This paper deals with the determination of the grain boundary erosion dependent on the degree of deformation and heat treatment of the stainless steel AISI 316L.

  14. Beryllium Related Matter

    Energy Technology Data Exchange (ETDEWEB)

    Gaylord, R F

    2008-12-23

    In recent months, LLNL has identified, commenced, and implemented a series of interim controls, compensatory measures, and initiatives to ensure worker safety, and improve safety processes with regards to potential worker exposure to beryllium. Many of these actions have been undertaken in response to the NNSA Independent Review (COR-TS-5/15/2008-8550) received by LLNL in November of 2008. Others are the result of recent discoveries, events or incidents, and lessons learned, or were scheduled corrective actions from earlier commitments. Many of these actions are very recent in nature, or are still in progress, and vary in the formality of implementation. Actions are being reviewed for effectiveness as they progress. The documentation of implementation, and review of effectiveness, when appropriate, of these actions will be addressed as part of the formal Corrective Action Plan addressing the Independent Review. The mitigating actions taken fall into the following categories: (1) Responses to specific events/concerns; (2) Development of interim controls; (3) Review of ongoing activities; and (4) Performance improvement measures.

  15. Mineral resource of the month: beryllium

    Science.gov (United States)

    ,

    2013-01-01

    The article discusses information about Beryllium. It notes that Beryllium is a light metal that has a gray color. The metal is used in the production of parts and devices including bearings, computer-chip heat sinks, and output windows of X-ray tubes. The article mentions Beryllium's discovery in 1798 by French chemist, Louis-Nicolas Vanquelin. It cites that bertrandite and beryl are the principal mineral components for the commercial production of beryllium.

  16. Beryllium--important for national defense

    Science.gov (United States)

    Boland, M.A.

    2012-01-01

    Beryllium is one of the lightest and stiffest metals, but there was little industrial demand for it until the 1930s and 1940s when the aerospace, defense, and nuclear sectors began using beryllium and its compounds. Beryllium is now classified by the U.S. Department of Defense as a strategic and critical material because it is used in products that are vital to national security. The oxide form of beryllium was identified in 1797, and scientists first isolated metallic beryllium in 1828. The United States is the world's leading source of beryllium. A single mine at Spor Mountain, Utah, produced more than 85 percent of the beryllium mined worldwide in 2010. China produced most of the remainder, and less than 2 percent came from Mozambique and other countries. National stockpiles also provide significant amounts of beryllium for processing. To help predict where future beryllium supplies might be located, U.S.Geological Survey (USGS) scientists study how and where beryllium resources are concentrated in Earth's crust and use that knowledge to assess the likelihood that undiscovered beryllium resources may exist. Techniques to assess mineral resources have been developed by the USGS to support the stewardship of Federal lands and to better evaluate mineral resource availability in a global context. The USGS also compiles statistics and information on the worldwide supply of, demand for, and flow of beryllium. These data are used to inform U.S. national policymaking.

  17. 10 CFR 850.33 - Beryllium emergencies.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Beryllium emergencies. 850.33 Section 850.33 Energy DEPARTMENT OF ENERGY CHRONIC BERYLLIUM DISEASE PREVENTION PROGRAM Specific Program Requirements § 850.33 Beryllium emergencies. (a) The responsible employer must comply with 29 CFR 1910.120(l) for...

  18. Neutron irradiation of beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Gelles, D.S.; Ermi, R.M. [Pacific Northwest National Lab., Richland, WA (United States); Tsai, H. [Argonne National Lab., IL (United States)

    1998-03-01

    Seven subcapsules from the FFTF/MOTA 2B irradiation experiment containing 97 or 100% dense sintered beryllium cylindrical specimens in depleted lithium have been opened and the specimens retrieved for postirradiation examination. Irradiation conditions included 370 C to 1.6 {times} 10{sup 22} n/cm{sup 2}, 425 C to 4.8 {times} 10{sup 22} n/cm{sup 2}, and 550 C to 5.0 {times} 10{sup 22} n/cm{sup 2}. TEM specimens contained in these capsules were also retrieved, but many were broken. Density measurements of the cylindrical specimens showed as much as 1.59% swelling following irradiation at 500 C in 100% dense beryllium. Beryllium at 97% density generally gave slightly lower swelling values.

  19. Beryllium strain under dynamic loading

    Directory of Open Access Journals (Sweden)

    Pushkov Victor

    2015-01-01

    Full Text Available There are some data (not much on dynamic characteristics of beryllium that are important, for example, when estimating construction performance at NPP emergencies. A number of data on stress-strain curves, spall strength, shear strength, fracture and structure responses of shock loaded beryllium have obtained in US and Russian laboratories. For today the model description of this complex metal behavior does not have a reasonable agreement with the experimental data, thus a wider spectrum of experimental data is required. This work presents data on dynamic compression-test diagrams of Russian beryllium. Experiments are performed using Hopkinson bar method (SHPB. Strain rates were ε ∼ 103 s−1.

  20. Analysis of microstructure and mechanical properties of aluminium-copper joints welded by FSW process

    Science.gov (United States)

    Iordache, M.; Sicoe, G.; Iacomi, D.; Niţu, E.; Ducu, C.

    2017-08-01

    The research conducted in this article aimed to check the quality of joining some dissimilar materials Al-Cu by determining the mechanical properties and microstructure analysis. For the experimental measurements there were used tin alloy Al - EN-AW-1050A with a thickness of 2 mm and Cu99 sheet with a thickness of 2 mm, joined by FSW weld overlay. The main welding parameters were: rotating speed of the rotating element 1400 rev/min, speed of the rotating element 50 mm/min. The experimental results were determined on samples specially prepared for metallographic analysis. In order to prepare samples for their characterization, there was designed and built a device that allowed simultaneous positioning and fixing for grinding. The characteristics analyzed in the joint welded samples were mictrostructure, microhardness and residual stresses. The techniques used to determine these characteristics were optical microscopy, electron microscopy with fluorescence radioactive elemental analysis (EDS), Vickers microhardness line - HV0.3 and X-ray diffractometry.

  1. Worker Environment Beryllium Characterization Study

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environment, Safety, Health & Quality

    2009-12-28

    This report summarizes the conclusion of regular monitoring of occupied buildings at the Nevada Test Site and North Las Vegas facility to determine the extent of beryllium (Be) contamination in accordance with Judgment of Needs 6 of the August 14, 2003, “Minnema Report.”

  2. Development of Be/Glidcop joint obtained by hot isostatic pressing diffusion bonding for high in-service temperature

    Energy Technology Data Exchange (ETDEWEB)

    Saint-Antonin, F.; Bucci, P.; Burlet, H.; Le Marois, G. [CEA Centre d`Etudes de Grenoble, 38 (France); Barberi, D.; Laille, A.

    1998-01-01

    This paper addresses some aspects of the beryllium-Glidcop joining by Hot Isostatic Pressing diffusion Bonding. The quality of a joint is mainly dependent on the interface microstructure. Thus, as Be/copper direct bonding is not recommended, the choice of interlayers is a critical point. The joining process parameters, i.e. temperature, pressure and time, must take into account the in-service requirements, the mechanical and metallurgical properties of each material. The Be/Glidcop joining process developed at CEA/Grenoble is presented here. (author)

  3. OVERVIEW OF BERYLLIUM SAMPLING AND ANALYSIS

    Energy Technology Data Exchange (ETDEWEB)

    Brisson, M

    2009-04-01

    Because of its unique properties as a lightweight metal with high tensile strength, beryllium is widely used in applications including cell phones, golf clubs, aerospace, and nuclear weapons. Beryllium is also encountered in industries such as aluminium manufacturing, and in environmental remediation projects. Workplace exposure to beryllium particulates is a growing concern, as exposure to minute quantities of anthropogenic forms of beryllium may lead to sensitization and to chronic beryllium disease, which can be fatal and for which no cure is currently known. Furthermore, there is no known exposure-response relationship with which to establish a 'safe' maximum level of beryllium exposure. As a result, the current trend is toward ever lower occupational exposure limits, which in turn make exposure assessment, both in terms of sampling and analysis, more challenging. The problems are exacerbated by difficulties in sample preparation for refractory forms of beryllium, such as beryllium oxide, and by indications that some beryllium forms may be more toxic than others. This chapter provides an overview of sources and uses of beryllium, health risks, and occupational exposure limits. It also provides a general overview of sampling, analysis, and data evaluation issues that will be explored in greater depth in the remaining chapters. The goal of this book is to provide a comprehensive resource to aid personnel in a wide variety of disciplines in selecting sampling and analysis methods that will facilitate informed decision-making in workplace and environmental settings.

  4. Defense programs beryllium good practice guide

    Energy Technology Data Exchange (ETDEWEB)

    Herr, M.

    1997-07-01

    Within the DOE, it has recently become apparent that some contractor employees who have worked (or are currently working) with and around beryllium have developed chronic beryllium disease (CBD), an occupational granulomatous lung disorder. Respiratory exposure to aerosolized beryllium, in susceptible individuals, causes an immunological reaction that can result in granulomatous scarring of the lung parenchyma, shortness of breath, cough, fatigue, weight loss, and, ultimately, respiratory failure. Beryllium disease was originally identified in the 1940s, largely in the fluorescent light industry. In 1950, the Atomic Energy Commission (AEC) introduced strict exposure standards that generally curtailed both the acute and chronic forms of the disease. Beginning in 1984, with the identification of a CBD case in a DOE contractor worker, there was increased scrutiny of both industrial hygiene practices and individuals in this workforce. To date, over 100 additional cases of beryllium-specific sensitization and/or CBD have been identified. Thus, a disease previously thought to be largely eliminated by the adoption of permissible exposure standards 45 years ago is still a health risk in certain workforces. This good practice guide forms the basis of an acceptable program for controlling workplace exposure to beryllium. It provides (1) Guidance for minimizing worker exposure to beryllium in Defense Programs facilities during all phases of beryllium-related work, including the decontamination and decommissioning (D&D) of facilities. (2) Recommended controls to be applied to the handling of metallic beryllium and beryllium alloys, beryllium oxide, and other beryllium compounds. (3) Recommendations for medical monitoring and surveillance of workers exposed (or potentially exposed) to beryllium, based on the best current understanding of beryllium disease and medical diagnostic tests available. (4) Site-specific safety procedures for all processes of beryllium that is likely to

  5. Beryllium Lymphocyte Proliferation Test Surveillance Identifies Clinically Significant Beryllium Disease

    Science.gov (United States)

    Mroz, Margaret M.; Maier, Lisa A.; Strand, Matthew; Silviera, Lori; Newman, Lee S.

    2011-01-01

    Background Workplace surveillance identifies chronic beryllium disease (CBD) but it remains unknown over what time frame mild CBD will progress to a more severe form. Methods We examined physiology and treatment in 229 beryllium sensitization (BeS) and 171 CBD surveillance-identified cases diagnosed from 1982 to 2002. Never smoking CBD cases (81) were compared to never smoking BeS patients (83) to assess disease progression. We compared CBD machinists to non-machinists to examine effects of exposure. Results At baseline, CBD and BeS cases did not differ significantly in exposure time or physiology. CBD patients were more likely to have machined beryllium. Of CBD cases, 19.3% went on to require oral immunosuppressive therapy. At 30 years from first exposure, measures of gas exchange were significantly worse and total lung capacity was lower for CBD subjects. Machinists had faster disease progression as measured by pulmonary function testing and gas exchange. Conclusions Medical surveillance for CBD identifies individuals at significant risk of disease progression and impairment with sufficient time since first exposure. PMID:19681064

  6. Mutagenicity, carcinogenicity and teratogenicity of beryllium.

    Science.gov (United States)

    Léonard, A; Lauwerys, R

    1987-07-01

    The carcinogenicity of a number of beryllium compounds has been confirmed in experiments on laboratory animals and this metal has to be treated as a possible carcinogenic threat to man. These carcinogenic properties are associated with mutagenic activity as shown by the results of short-term tests performed in vitro with beryllium chloride and beryllium sulfate. These soluble beryllium compounds can produce some infidelity of in vitro synthesis, forward gene mutations in microorganisms and in mammalian cells. They are also able to induce cell transformation. In addition to the positive results obtained in several short-term assays beryllium compounds have been found to bind to nucleoproteins, to inhibit certain enzymes needed for DNA synthesis, to bind nucleic acids to cell membranes and to inhibit microtubule polymerization. The teratogenicity of beryllium salts is relatively unknown and needs additional investigation.

  7. Advances in identifying beryllium sensitization and disease.

    Science.gov (United States)

    Middleton, Dan; Kowalski, Peter

    2010-01-01

    Beryllium is a lightweight metal with unique qualities related to stiffness, corrosion resistance, and conductivity. While there are many useful applications, researchers in the 1930s and 1940s linked beryllium exposure to a progressive occupational lung disease. Acute beryllium disease is a pulmonary irritant response to high exposure levels, whereas chronic beryllium disease (CBD) typically results from a hypersensitivity response to lower exposure levels. A blood test, the beryllium lymphocyte proliferation test (BeLPT), was an important advance in identifying individuals who are sensitized to beryllium (BeS) and thus at risk for developing CBD. While there is no true "gold standard" for BeS, basic epidemiologic concepts have been used to advance our understanding of the different screening algorithms.

  8. Investigation of Be/Cu joints via HHF tests of small-scale mockups

    Energy Technology Data Exchange (ETDEWEB)

    Giniatulin, R.; Gervash, A.; Komarov, V.L.; Litunovsky, N.; Mazul, I.; Yablokov, N. [Efremov Inst., St. Petersburg (Russian Federation)

    1998-01-01

    Beryllium-copper (Be/Cu) joints in divertor components work under cyclic heat loads. To develop reliable joints small-scale mockups are fabricated by divertor technologies and tested under the divertor conditions. One of the critical damaging factors that exist in the divertor and have to be simulated is thermocyclic heat loads in the range of 1-15 MW/m{sup 2}. This work presents the divertor mockups that have beryllium tiles with different dimensions (5 x 5 - 44 x 44) mm{sup 2} brazed with copper alloy heat sink. The electron beam was used to braze these mockups so as to decrease the formation of brittle intermetallic layers. The description of mockups design, geometry of armour tiles and fabrication techniques are presented in the paper. The results of screening and thermocyclic tests of these mockups in the heat flux range of 2-12 MW/m{sup 2} with a number of cycles {approx}10{sup 3} are presented. The results of metallographic analysis are also presented. The results of fabrication and testing with small-scale mockups for first wall application are also described. (author)

  9. Inhibited solid propellant composition containing beryllium hydride

    Science.gov (United States)

    Thompson, W. W. (Inventor)

    1978-01-01

    An object of this invention is to provide a composition of beryllium hydride and carboxy-terminated polybutadiene which is stable. Another object of this invention is to provide a method for inhibiting the reactivity of beryllium hydride toward carboxy-terminated polybutadiene. It was found that a small amount of lecithin inhibits the reaction of beryllium hydride with the acid groups in carboxy terminated polybutadiene.

  10. High-temperature beryllium embrittlement

    Energy Technology Data Exchange (ETDEWEB)

    Pokrovsky, A.S. [Scientific Research Inst. of Atomic Reactors, Dimitrovgrad (Russian Federation); Fabritsiev, S.A. [D.V. Efremov Scientific Research Institute, 189631 St. Petersburg (Russian Federation); Bagautdinov, R.M. [Scientific Research Inst. of Atomic Reactors, Dimitrovgrad (Russian Federation); Goncharenko, Yu.D. [Scientific Research Inst. of Atomic Reactors, Dimitrovgrad (Russian Federation)

    1996-10-01

    The neutron irradiation effect on the mechanical properties, swelling and fracture surface structure of various beryllium grades was studied in the BOR-60 reactor at 340 to 350 C up to a fluence of 7.2 x 10{sup 21} n/cm{sup 2}. At a mechanical testing temperature of 400 C there was observed a strong anisotropy of plastic beryllium deformation depending on the direction of sample cutting relative to the pressing direction. An increase of the testing temperature up to 700 C resulted in an abrupt embrittlement of all irradiated samples. In the most part of the surface structure the intercrystallite fracture along the grain boundaries was covered entirely with large pores, 1 to 4 {mu}m in size. It was suggested that the increased rate of pore formation along the grain boundaries resulted from a high-temperature embrittlement under irradiation. (orig.).

  11. Beryllium thin films for resistor applications

    Science.gov (United States)

    Fiet, O.

    1972-01-01

    Beryllium thin films have a protective oxidation resistant property at high temperature and high recrystallization temperature. However, the experimental film has very low temperature coefficient of resistance.

  12. Diffusion bonding beryllium to Reduced Activation Ferritic Martensitic steel: Development of processes and techniques

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, R.M., E-mail: hunt52@llnl.gov [Mechanical and Aerospace Engineering Department, UCLA, 44-128 Engineering IV, 420 Westwood Plaza, Los Angeles, CA 90025-1597 (United States); Goods, S.H., E-mail: shgoods@sandia.gov [Sandia National Laboratories (United States); Ying, A., E-mail: ying@fusion.ucla.edu [Mechanical and Aerospace Engineering Department, UCLA, 44-128 Engineering IV, 420 Westwood Plaza, Los Angeles, CA 90025-1597 (United States); Dorn, C.K., E-mail: christopher.dorn@materion.com [Materion Brush Beryllium and Composites (United States); Abdou, M., E-mail: abdou@fusion.ucla.edu [Mechanical and Aerospace Engineering Department, UCLA, 44-128 Engineering IV, 420 Westwood Plaza, Los Angeles, CA 90025-1597 (United States)

    2012-09-15

    Highlights: Black-Right-Pointing-Pointer We diffusion bonded Be to Reduced Activation Ferritic Martensitic steel. Black-Right-Pointing-Pointer Thin copper and titanium interlayers improved the bond's shear strength to 168 MPa. Black-Right-Pointing-Pointer A slow cooling scheme and intermediate hold step greatly increased bond strength. Black-Right-Pointing-Pointer Failure occurred in Be-Ti and Cu-Ti intermetallic compounds. - Abstract: Beryllium was successfully bonded to a Reduced Activation Ferritic Martensitic (RAFM) steel with a maximum strength of 150 MPa in tension and 168 MPa in shear. These strengths were achieved using Hot Isostatic Pressing (HIP), at temperatures between 700 Degree-Sign C and 750 Degree-Sign C for 2 h and under a pressure of 103 MPa. To obtain these strengths, 10 {mu}m of titanium and 20 {mu}m of copper were deposited on the beryllium substrate prior to HIP bonding. The copper film acted a bonding aid to the RAFM steel, while the titanium acted as a diffusion barrier between the copper and the beryllium, suppressing the formation of brittle intermetallics that are known to compromise mechanical performance. Slow cooling from the peak HIP temperature along with an imposed hold time at 450 Degree-Sign C further enhanced the final mechanical strength of the bond.

  13. Effects of processing conditions and ambient environment on the microstructure and fracture strength of copper/niobium/copper interlayer joints for alumina

    OpenAIRE

    Marks, Robert Alan

    1999-01-01

    Partial transient liquid phase (PTLP) bonding is a technique which can be used to join ceramics with metals and is used to form niobium-based joints for alumina. The principal advantage to PTLP bonding is that it enables refractory joints to be fabricated at temperatures below those typically required by solid state diffusion bonding. A thorough review of the important parameters (chemical compatibility, thermal expansion match, sufficient wettability of the liquid phase on the solid pha...

  14. Manufacturing and thermomechanical testing of actively cooled all beryllium high heat flux test pieces

    Energy Technology Data Exchange (ETDEWEB)

    Vasiliev, N.N.; Sokolov, Yu.A.; Shatalov, G.E. [and others

    1995-09-01

    One of the problems affiliated to ITER high heat flux elements development is a problem of interface of beryllium protection with heat sink routinely made of copper alloys. To get rid of this problem all beryllium elements could be used as heat receivers in places of enhanced thermal loads. In accordance with this objectives four beryllium test pieces of two types have been manufactured in {open_quotes}Institute of Beryllium{close_quotes} for succeeding thermomechanical testing. Two of them were manufactured in accordance with JET team design; they are round {open_quotes}hypervapotron type{close_quotes} test pieces. Another two ones are rectangular test sections with a twisted tape installed inside of the circular channel. Preliminary stress-strain analysis have been performed for both type of the test pieces. Hypervapotrons have been shipped to JET where they were tested on JET test bed. Thermomechanical testing of pieces of the type of {open_quotes}swirl tape inside of tube{close_quotes} have been performed on Kurchatov Institute test bed. Chosen beryllium grade properties, some details of manufacturing, results of preliminary stress-strain analysis and thermomechanical testing of the test pieces {open_quotes}swirl tape inside of tube{close_quotes} type are given in this report.

  15. Investigation on bonding defects in ITER first wall beryllium armour components by combining analytical and experimental methods

    Energy Technology Data Exchange (ETDEWEB)

    Pérez, Germán, E-mail: german.perez.pichel@gmail.com; Mitteau, Raphaël; Eaton, Russell; Raffray, René

    2015-12-15

    Highlights: • Bonding defects at the ITER first wall beryllium armour are studied. • Experimental and analytical methods are combined. • Models supporting test results interpretation are proposed. • Guidelines for new experimental protocols are suggested. • Contribution to the definition of defects acceptance criteria. - Abstract: The reliability of the plasma facing components (PFCs) is essential for the efficient plasma operation in a fusion machine. This concerns especially the bond between the armour tiles facing the plasma and the heat sink material (copper alloy). The different thermal expansions of the bonded materials cause a stress distribution in the bond, which peaks at the bond edge. Under cyclic heat flux and accounting for the possible presence of bonding defects, this stress could reach a level where the component might be jeopardised. Because of the complexity of describing realistically by analyses and models the stress evolution in the bond, “design by experiments” is the main procedure for defining and qualifying the armour joint. Most of the existing plasma operation know-how on actively cooled PFCs has been obtained with carbon composite armour tiles. In ITER, the tiles of the first wall are made out of beryllium, which means that the know-how is progressively adapted to this specific bimetallic pair. Nonetheless, analyses are still performed for supporting the R&D experimental programme. This paper: explores methods for combining experimental results with finite element and statistical analyses; benchmarks test results; proposes hypothesis and rationales consistent with test results interpretations; suggests guidelines for defining possible further experimental protocols; and contributes to the definition of defects acceptance criteria.

  16. Beryllium particulate exposure and disease relations in a beryllium machining plant.

    Science.gov (United States)

    Kelleher, P C; Martyny, J W; Mroz, M M; Maier, L A; Ruttenber, A J; Young, D A; Newman, L S

    2001-03-01

    We examined the relationship between exposure to beryllium and the presence of beryllium sensitization (BeS) and chronic beryllium disease (CBD) in a cohort of workers in a beryllium precision machining facility. Twenty workers with BeS or CBD (cases) were compared with 206 worker-controls in a case-control study. Exposure for each job title was measured using cascade impactors placed in the workers' breathing zone to measure total beryllium exposure and exposure to particles 0.20. In conclusion, increased cumulative and LTW exposure to total and respirable beryllium was observed in workers with CBD or BeS compared with the controls. These results support efforts to control beryllium exposure in the workplace.

  17. Investigation of beryllium/steam interaction

    Energy Technology Data Exchange (ETDEWEB)

    Chekhonadskikh, A.M.; Vurim, A.D.; Vasilyev, Yu.S.; Pivovarov, O.S. [Inst. of Atomic Energy National Nuclear Center of the Republic of Kazakstan Semipalatinsk (Kazakhstan); Shestakov, V.P.; Tazhibayeva, I.L.

    1998-01-01

    In this report program on investigations of beryllium emissivity and transient processes on overheated beryllium surface attacked by water steam to be carried out in IAE NNC RK within Task S81 TT 2096-07-16 FR. The experimental facility design is elaborated in this Report. (author)

  18. Modeling of hydrogen interactions with beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Longhurst, G.R. [Lockheed Martin Idaho Technologies Co., Idaho Falls, ID (United States)

    1998-01-01

    In this paper, improved mathematical models are developed for hydrogen interactions with beryllium. This includes the saturation effect observed for high-flux implantation of ions from plasmas and retention of tritium produced from neutronic transmutations in beryllium. Use of the models developed is justified by showing how they can replicated experimental data using the TMAP4 tritium transport code. (author)

  19. Benchmark Experiment for Beryllium Slab Samples

    Institute of Scientific and Technical Information of China (English)

    NIE; Yang-bo; BAO; Jie; HAN; Rui; RUAN; Xi-chao; REN; Jie; HUANG; Han-xiong; ZHOU; Zu-ying

    2015-01-01

    In order to validate the evaluated nuclear data on beryllium,a benchmark experiment has been performed at China Institution of Atomic Energy(CIAE).Neutron leakage spectra from pure beryllium slab samples(10cm×10cm×11cm)were measured at 61°and 121°using timeof-

  20. BERYLLIUM MEASUREMENT IN COMMERCIALLY AVAILABLE WET WIPES

    Energy Technology Data Exchange (ETDEWEB)

    Youmans-Mcdonald, L.

    2011-02-18

    Analysis for beryllium by fluorescence is now an established method which is used in many government-run laboratories and commercial facilities. This study investigates the use of this technique using commercially available wet wipes. The fluorescence method is widely documented and has been approved as a standard test method by ASTM International and the National Institute for Occupational Safety and Health (NIOSH). The procedure involves dissolution of samples in aqueous ammonium bifluoride solution and then adding a small aliquot to a basic hydroxybenzoquinoline sulfonate fluorescent dye (Berylliant{trademark} Inc. Detection Solution Part No. CH-2) , and measuring the fluorescence. This method is specific to beryllium. This work explores the use of three different commercial wipes spiked with beryllium, as beryllium acetate or as beryllium oxide and subsequent analysis by optical fluorescence. The effect of possible interfering metals such as Fe, Ti and Pu in the wipe medium is also examined.

  1. Some characteristics of fine beryllium particle combustion

    Science.gov (United States)

    Davydov, D. A.; Kholopova, O. V.; Kolbasov, B. N.

    2007-08-01

    Beryllium dust will be produced under plasma interaction with beryllium armor of the first wall in ITER. Exothermal reaction of this dust with water steam or air, which can leak into the reactor vacuum chamber in some accidents, gives concern in respect to reactor safety. Results of studies devoted to combustion of fine beryllium particles are reviewed in the paper. A chemically active medium and elevated temperature are prerequisite to the combustion of beryllium particles. Their ignition is hampered by oxide films, which form a diffusion barrier on the particle surface as a result of pre-flame oxidation. The temperature to initiate combustion of particles depends on flame temperature, particle size, composition of combustible mixture, heating rate and other factors. In mixtures enriched with combustible, the flame temperature necessary to ignite individual particles approaches the beryllium boiling temperature.

  2. 40 CFR 421.150 - Applicability: Description of the primary beryllium subcategory.

    Science.gov (United States)

    2010-07-01

    ... primary beryllium subcategory. 421.150 Section 421.150 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Primary Beryllium Subcategory § 421.150 Applicability: Description of the primary beryllium... beryllium by primary beryllium facilities processing beryllium ore concentrates or beryllium hydroxide...

  3. Postirradiation examination of beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Gelles, D.S. [Pacific Northwest National Lab., Richland, WA (United States)

    1998-03-01

    Postirradiation examinations of COBRA-1A beryllium pebbles irradiated in the EBR-II fast reactor at neutron fluences which generated 2700--3700 appm helium have been performed. Measurements included density change, optical microscopy, scanning electron microscopy, and transmission electron microscopy. The major change in microstructure is development of unusually shaped helium bubbles forming as highly non-equiaxed thin platelet-like cavities on the basal plane. Measurement of the swelling due to cavity formation was in good agreement with density change measurements.

  4. Technical issues for beryllium use in fusion blanket applications

    Energy Technology Data Exchange (ETDEWEB)

    McCarville, T.J.; Berwald, D.H.; Wolfer, W.; Fulton, F.J.; Lee, J.D.; Maninger, R.C.; Moir, R.W.; Beeston, J.M.; Miller, L.G.

    1985-01-01

    Beryllium is an excellent non-fissioning neutron multiplier for fusion breeder and fusion electric blanket applications. This report is a compilation of information related to the use of beryllium with primary emphasis on the fusion breeder application. Beryllium resources, production, fabrication, properties, radiation damage and activation are discussed. A new theoretical model for beryllium swelling is presented.

  5. Exposure-response analysis for beryllium sensitization and chronic beryllium disease among workers in a beryllium metal machining plant.

    Science.gov (United States)

    Madl, Amy K; Unice, Ken; Brown, Jay L; Kolanz, Marc E; Kent, Michael S

    2007-06-01

    The current occupational exposure limit (OEL) for beryllium has been in place for more than 50 years and was believed to be protective against chronic beryllium disease (CBD) until studies in the 1990s identified beryllium sensitization (BeS) and subclinical CBD in the absence of physical symptoms. Inconsistent sampling and exposure assessment methodologies have often prevented the characterization of a clear exposure-response relationship for BeS and CBD. Industrial hygiene (3831 personal lapel and 616 general area samples) and health surveillance data from a beryllium machining facility provided an opportunity to reconstruct worker exposures prior to the ascertainment of BeS or the diagnosis of CBD. Airborne beryllium concentrations for different job titles were evaluated, historical trends of beryllium levels were compared for pre- and postengineering control measures, and mean and upper bound exposure estimates were developed for workers identified as beryllium sensitized or diagnosed with subclinical or clinical CBD. Five approaches were used to reconstruct historical exposures of each worker: industrial hygiene data were pooled by year, job title, era of engineering controls, and the complete work history (lifetime weighted average) prior to diagnosis. Results showed that exposure metrics based on shorter averaging times (i.e., year vs. complete work history) better represented the upper bound worker exposures that could have contributed to the development of BeS or CBD. Results showed that beryllium-sensitized and CBD workers were exposed to beryllium concentrations greater than 0.2 microg/m3 (95th percentile), and 90% were exposed to concentrations greater than 0.4 microg/m3 (95th percentile) within a given year of their work history. Based on this analysis, BeS and CBD generally occurred as a result of exposures greater than 0.4 microg/m3 and maintaining exposures below 0.2 microg/m3 95% of the time may prevent BeS and CBD in the workplace.

  6. Prediction of grain size and mechanical properties in friction stir welded pure copper joints using a thermal model

    DEFF Research Database (Denmark)

    Heidarzadeh, A.; Jabbaribehnam, Mirmasoud; Esmaily, M.

    2015-01-01

    In this study, a thermal model was developed and applied to simulate the friction stir welding of pure copper plates with the thickness of 2 mm. The different traverse speeds of 100, 200, 300, and 400 mm min−1 and rotational speeds of 400, 700, 900 rev min−1 were considered as welding parameters....

  7. A theoretical framework for evaluating analytical digestion methods for poorly soluble particulate beryllium.

    Science.gov (United States)

    Stefaniak, Aleksandr B; Brink, Christopher A; Dickerson, Robert M; Day, Gregory A; Brisson, Michael J; Hoover, Mark D; Scripsick, Ronald C

    2007-04-01

    Complete digestion of all chemical forms and sizes of particulate analytes in environmental samples is usually necessary to obtain accurate results with atomic spectroscopy. In the current study, we investigate the physicochemical properties of beryllium particles likely to be encountered in samples collected from different occupational environments and present a hypothesis that a dissolution theory can be used as a conceptual framework to guide development of strategies for digestion procedures. For monodisperse single-chemical constituent primary particles, such as those encountered when handling some types of beryllium oxide (BeO) powder, theory predicts that a digestion procedure is sufficient when it completely dissolves all primary particles, independent of cluster size. For polydisperse single-chemical constituent particles, such as those encountered during the handling of some types of beryllium metal powder, theory predicts that a digestion procedure is sufficient only when it completely dissolves the largest particle in the sample. For samples with unknown or multi-chemical constituent particles and with particles having undefined sizes, e.g., fume emissions from a copper-beryllium alloy furnace operation or dust from a beryl ore crushing operation, a surface area-limited and single-constituent-dependent dissolution theory may not predict complete dissolution, thereby requiring non-routine robust treatment procedures with post-digestion filtration, followed by examination of residual particulate material. Additionally, for beryllium, and likely other poorly soluble materials, particulate reference materials of various chemical forms and size distributions are needed to better evaluate and harmonize analytical digestion procedures. Figure Generation of aerosol particles during machining of beryllium oxide.

  8. Measuring the stability of three copper alloys

    Science.gov (United States)

    Doiron, Theodore D.; Stoup, John R.; Snoots, Patricia; Chaconas, Grace

    1990-11-01

    In this paper we report measurements of the dimensional stability of samples of brass, beryllium copper, and tellurium copper taken over an 18 month time span. Of the materials, brass was the most stable, decreasing slightly in length at the rate of 1 part per million per year (ppm/y) with an uncertainty (3a) of about 1 ppm/y. Tellurium copper shrank at an average rate of 2.Li ppm/y and beryllium copper, the least stable, at the rate of 5.8 ppm/y. To measure the instrumental uncertainty 4 samples of each material were measured, and the measurement scheme was designed to detect and correct for thermal drift ,during measurements. The experiment design problems associated with these measurements and the associated uncertainties are discussed.

  9. Recommended design correlations for S-65 beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Billone, M.C. [Argonne National Lab., IL (United States)

    1995-09-01

    The properties of tritium and helium behavior in irradiated beryllium are reviewed, along with the thermal-mechanical properties needed for ITER design analysis. Correlations are developed to describe the performance of beryllium in a fusion reactor environment. While this paper focuses on the use of beryllium as a plasma-facing component (PFC) material, the correlations presented here can also be used to describe the performance of beryllium as a neutron multiplier for a tritium breeding blanket. The performance properties for beryllium are subdivided into two categories: properties which do not change with irradiation damage to the bulk of the material; and properties which are degraded by neutron irradiation. The irradiation-independent properties described within are: thermal conductivity, specific heat capacity, thermal expansion, and elastic constants. Irradiation-dependent properties include: yield strength, ultimate tensile strength, plastic tangent modulus, uniform and total tensile elongation, thermal and irradiation-induced creep strength, He-induced swelling and tritium retention/release. The approach taken in developing properties correlations is to describe the behavior of dense, pressed S-65 beryllium -- the material chosen for ITER PFC application -- as a function of temperature. As there are essentially no data on the performance of porous and/or irradiated S-65 beryllium, the degradation of properties with as-fabricated porosity and irradiation are determined from the broad data base on S-200F, as well as other types and grades, and applied to S-65 beryllium by scaling factors. The resulting correlations can be used for Be produced by vacuum hot pressing (VHP) and cold-pressing (CP)/sintering(S)/hot-isostatic-pressing (HIP). The performance of plasma-sprayed beryllium is discussed but not quantified.

  10. THE IDAHO NATIONAL LABORATORY BERYLLIUM TECHNOLOGY UPDATE

    Energy Technology Data Exchange (ETDEWEB)

    Glen R. Longhurst

    2007-12-01

    A Beryllium Technology Update meeting was held at the Idaho National Laboratory on July 18, 2007. Participants came from the U.S., Japan, and Russia. There were two main objectives of this meeting. One was a discussion of current technologies for beryllium in fission reactors, particularly the Advanced Test Reactor and the Japan Materials Test Reactor, and prospects for material availability in the coming years. The second objective of the meeting was a discussion of a project of the International Science and Technology Center regarding treatment of irradiated beryllium for disposal. This paper highlights discussions held during that meeting and major conclusions reached

  11. Metallurgical viewpoints on the brittleness of beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Lagerberg, G.

    1960-02-15

    At present the development and use of beryllium metal for structural applications is severely hampered by its brittleness. Reasons for this lack of ductility are reviewed in discussing the deformation behaviour of beryllium in relation to other hexagonal metals. The ease of fracturing in beryllium is assumed to be a consequence of a limited number of deformation modes in combination with high deformation resistance. Models for the nucleation of fracture are suggested. The relation of ductility to elastic constants as well as to grain size, texture and alloying additions is discussed.

  12. Yunnan Copper Co., Ltd. Invested 1.5 Billion Yuan for 200,000-Ton Refined Copper Project in Baoding

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    <正>Yunnan Copper(Group)Co.,Ltd.has signed a strategic agreement with Baoding Municipal Government of Heibei Province in Kunming on the joint development of a copper smelting project.With the joint investment from Baoding Xinxian Government,Yunnan Copper Co.,Ltd.and Baoding Dali Copper Ltd,a copper refinery with an annual capacity of

  13. Efficacy of serial medical surveillance for chronic beryllium disease in a beryllium machining plant.

    Science.gov (United States)

    Newman, L S; Mroz, M M; Maier, L A; Daniloff, E M; Balkissoon, R

    2001-03-01

    There is limited information on the use of the blood beryllium lymphocyte proliferation test (BeLPT) at regular intervals in medical surveillance. Employees of a beryllium machining plant were screened with the BeLPT biennially, and new employees were screened within 3 months of hire. Of 235 employees screened from 1995 to 1997, a total of 15 (6.4%) had confirmed abnormal BeLPT results indicating beryllium sensitization; nine of these employees were diagnosed with chronic beryllium disease. Four of the 15 cases were diagnosed within 3 months of first exposure. When 187 of the 235 employees participated in biennial screening in 1997 to 1999, seven more had developed beryllium sensitization or chronic beryllium disease, increasing the overall rate to 9.4% (22 of 235). The blood BeLPT should be used serially in beryllium disease surveillance to capture new or missed cases of sensitization and disease. Beryllium sensitization and chronic beryllium disease can occur within 50 days of first exposure in modern industry.

  14. Laser Spot Welding of Copper-aluminum Joints Using a Pulsed Dual Wavelength Laser at 532 and 1064 nm

    Science.gov (United States)

    Stritt, Peter; Hagenlocher, Christian; Kizler, Christine; Weber, Rudolf; Rüttimann, Christoph; Graf, Thomas

    A modulated pulsed laser source emitting green and infrared laser light is used to join the dissimilar metals copper and aluminum. The resultant dynamic welding process is analyzed using the back reflected laser light and high speed video observations of the interaction zone. Different pulse shapes are applied to influence the melt pool dynamics and thereby the forming grain structure and intermetallic phases. The results of high-speed images and back-reflections prove that a modulation of the pulse shape is transferred to oscillations of the melt pool at the applied frequency. The outcome of the melt pool oscillation is shown by the metallurgically prepared cross-section, which indicates different solidification lines and grain shapes. An energy-dispersivex-ray analysis shows the mixture and the resultant distribution of the two metals, copper and aluminum, within the spot weld. It can be seen that the mixture is homogenized the observed melt pool oscillations.

  15. Progress on a Cavity with Beryllium Walls for Muon Ionization Cooling Channel R&D.

    Energy Technology Data Exchange (ETDEWEB)

    Bowring, D. L.; DeMello, A. J.; Lambert, A. R.; Li, D.; Virostek, S.; Zisman, M.; Kaplan, D.; Palmer, R. B.

    2012-05-20

    The Muon Accelerator Program (MAP) collaboration is working to develop an ionization cooling channel for muon beams. An ionization cooling channel requires the operation of high-gradient, normal-conducting RF cavities in multi-Tesla solenoidal magnetic fields. However, experiments conducted at Fermilab?s MuCool Test Area (MTA) show that increasing the solenoidal field strength reduces the maximum achievable cavity gradient. This gradient limit is characterized by an RF breakdown process that has caused significant damage to copper cavity interiors. The damage may be caused by field-emitted electrons, focused by the solenoidal magnetic field onto small areas of the inner cavity surface. Local heating may then induce material fatigue and surface damage. Fabricating a cavity with beryllium walls would mitigate this damage due to beryllium?s low density, low thermal expansion, and high electrical and thermal conductivity. We address the design and fabrication of a pillbox RF cavity with beryllium walls, in order to evaluate the performance of high-gradient cavities in strong magnetic fields.

  16. Chronic Beryllium Disease Prevention Program Report

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S

    2012-03-29

    This document describes how Lawrence Livermore National Laboratory (LLNL) meets the requirements and management practices of federal regulation 10 CFR 850, 'Chronic Beryllium Disease Prevention Program (CBDPP).' This revision of the LLNL CBDPP incorporates clarification and editorial changes based on lessons learned from employee discussions, observations and reviews of Department of Energy (DOE) Complex and commercial industry beryllium (Be) safety programs. The information is used to strengthen beryllium safety practices at LLNL, particularly in the areas of: (1) Management of small parts and components; and (2) Communication of program status to employees. Future changes to LLNL beryllium activities and on-going operating experience will be incorporated into the program as described in Section S, 'Performance Feedback.'

  17. Hydrogen release from reactor-irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Klepikov, A.Kh. [Kazakh State Univ., Alma-Ata (Kazakstan); Tazhibaeva, I.L. [Kazakh State Univ., Alma-Ata (Kazakstan); Shestakov, V.P. [Kazakh State Univ., Alma-Ata (Kazakstan); Romanenko, O.G. [Kazakh State Univ., Alma-Ata (Kazakstan); Chikhray, Y.V. [Kazakh State Univ., Alma-Ata (Kazakstan); Kenzhin, E.A. [IAE NNC RK, Semipalatinsk-21 (Russian Federation); Cherepnin, Yu.S. [IAE NNC RK, Semipalatinsk-21 (Russian Federation); Tikhomirov, L.N. [IAE NNC RK, Semipalatinsk-21 (Russian Federation)

    1996-10-01

    Experiments on gas release of reactor-irradiated beryllium samples were carried out and compared to control samples. The simultaneous influence of reactor irradiation and exposure to hydrogen results in more hydrogen retention in beryllium, than if beryllium is initially irradiated and then exposed to hydrogen. Appearance of low temperature peaks at 460 K and 540 K with 0.71 eV/atom and 0.84 eV/atom desorption activation energies, respectively, assessed in a frame of a second order desorption model, is mainly responsible for the increase in hydrogen content. These peaks can be attributed to chemical hydrogen bonds with surface oxide. The simultaneous influence of hydrogen and nuclear reactor irradiation at a temperature of 1150 K was assumed to increase significantly microcrack formation near the surface of beryllium samples, resulting in an increase in low temperature peak intensities. (orig.).

  18. Synthesis and ceramization of polycarbosilane containing beryllium

    Institute of Scientific and Technical Information of China (English)

    黄小忠; 周珊; 程勇; 杜作娟; 段曦东; 王超英

    2014-01-01

    Polycarbosilane containing beryllium (BPCS) precursors was prepared by the reaction of polycarbosilane (PCS) with beryllium acetylacetone (Be (acac)2). The analysis of structures and components of BPCS demonstrates that their main structures are basically the same as PCS. Ceramization of BPCS precursors shows that BPCS precursors are organic below 600 °C and inorganic at 800 °C. At 1400 °C, BPCS precursors convert into silicon carbide ceramics. The ceramization of different beryllium content precursors were studied, which show that beryllium plays an important role in the inhibition of crystalline grain growth ofβ-SiC at high temperature and it can adjust the dielectric constant of silicon carbide ceramics.

  19. Microstructure and strength of TiAl/40Cr joint diffusion bonded with vanadium-copper filler metal

    Institute of Scientific and Technical Information of China (English)

    何鹏; 冯吉才; 钱乙余; 张炳刚

    2002-01-01

    Intermetallics TiAl was diffusion-bonded to steel 40Cr in vacuum furnace with interlayer V/Cu. The results show that infinite sosoloid that made for bond performance is formed at the interface of V/Cu and Cu/40Cr, and three acting layers are formed at the interface of TiAl/V including Ti3Al layer at TiAl side, intermittent V5Al8 layer in the middle and Ti-V sosoloid at V side. Fragile reactors V5Al8 arising at the interface lead to bad performance of joints, and the strength of the joint is 200MPa, while it was still higher than the strength of the joint intermetallics TiAl to 40Cr steel diffusion-bonded directly. Intermetallic TiAl and 40Cr steel are diffusion-bonded successfully by using a composite isolation layer V/Cu.

  20. Beryllium concentration in pharyngeal tonsils in children

    Directory of Open Access Journals (Sweden)

    Ewa Nogaj

    2014-06-01

    Full Text Available Power plant dust is believed to be the main source of the increased presence of the element beryllium in the environment which has been detected in the atmospheric air, surface waters, groundwater, soil, food, and cigarette smoke. In humans, beryllium absorption occurs mainly via the respiratory system. The pharyngeal tonsils are located on the roof of the nasopharynx and are in direct contact with dust particles in inhaled air. As a result, the concentration levels of beryllium in the pharyngeal tonsils are likely to be a good indicator of concentration levels in the air. The presented study had two primary aims: to investigate the beryllium concentration in pharyngeal tonsils in children living in southern Poland, and the appropriate reference range for this element in children’s pharyngeal tonsils. Pharyngeal tonsils were extracted from a total of 379 children (age 2–17 years, mean 6.2 ± 2.7 years living in southern Poland. Tonsil samples were mineralized in a closed cycle in a pressure mineralizer PDS 6, using 65% spectrally pure nitric acid. Beryllium concentration was determined using the ICP-AES method with a Perkin Elmer Optima 5300DVTM. The software Statistica v. 9 was used for the statistical analysis. It was found that girls had a significantly greater beryllium concentration in their pharyngeal tonsils than boys. Beryllium concentration varies greatly, mostly according to the place of residence. Based on the study results, the reference value for beryllium in pharyngeal tonsils of children is recommended to be determined at 0.02–0.04 µg/g.

  1. Benchmark Experiment for Beryllium Slab Samples

    Institute of Scientific and Technical Information of China (English)

    NIE; Yang-bo; BAO; Jie; HAN; Rui; RUAN; Xi-chao; REN; Jie; HUANG; Han-xiong; ZHOU; Zu-ying

    2013-01-01

    The neutron leakage spectra were measured at 60°from pure beryllium slab samples(10 cm×10 cm×5 cm and 10 cm×10 cm×11 cm)by TOF method.The experimental results were compared with the calculated ones by MCNP5 simulation,using the evaluated data of beryllium from CENDL3.1,

  2. Beryllium concentration in pharyngeal tonsils in children.

    Science.gov (United States)

    Nogaj, Ewa; Kwapulinski, Jerzy; Misiołek, Maciej; Golusiński, Wojciech; Kowol, Jolanta; Wiechuła, Danuta

    2014-01-01

    Power plant dust is believed to be the main source of the increased presence of the element beryllium in the environment which has been detected in the atmospheric air, surface waters, groundwater, soil, food, and cigarette smoke. In humans, beryllium absorption occurs mainly via the respiratory system. The pharyngeal tonsils are located on the roof of the nasopharynx and are in direct contact with dust particles in inhaled air. As a result, the concentration levels of beryllium in the pharyngeal tonsils are likely to be a good indicator of concentration levels in the air. The presented study had two primary aims: to investigate the beryllium concentration in pharyngeal tonsils in children living in southern Poland, and the appropriate reference range for this element in children's pharyngeal tonsils. Pharyngeal tonsils were extracted from a total of 379 children (age 2-17 years, mean 6.2 ± 2.7 years) living in southern Poland. Tonsil samples were mineralized in a closed cycle in a pressure mineralizer PDS 6, using 65% spectrally pure nitric acid. Beryllium concentration was determined using the ICP-AES method with a Perkin Elmer Optima 5300DVTM. The software Statistica v. 9 was used for the statistical analysis. It was found that girls had a significantly greater beryllium concentration in their pharyngeal tonsils than boys. Beryllium concentration varies greatly, mostly according to the place of residence. Based on the study results, the reference value for beryllium in pharyngeal tonsils of children is recommended to be determined at 0.02-0.04 µg/g.

  3. Tritium release from neutron irradiated beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Scaffidi-Argentina, F.; Werle, H. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reactortechnik

    1998-01-01

    One of the most important open issues related to beryllium for fusion applications refers to the kinetics of the tritium release as a function of neutron fluence and temperature. The EXOTIC-7 as well as the `Beryllium` experiments carried out in the HFR reactor in Petten are considered as the most detailed and significant tests for investigating the beryllium response under neutron irradiation. This paper reviews the present status of beryllium post-irradiation examinations performed at the Forschungszentrum Karlsruhe with samples from the above mentioned irradiation experiments, trying to elucidate the tritium release controlling processes. In agreement with previous studies it has been found that release starts at about 500-550degC and achieves a maximum at about 700-750degC. The observed release at about 500-550degC is probably due to tritium escaping from chemical traps, while the maximum release at about 700-750degC is due to tritium escaping from physical traps. The consequences of a direct contact between beryllium and ceramics during irradiation, causing tritium implanting in a surface layer of beryllium up to a depth of about 40 mm and leading to an additional inventory which is usually several times larger than the neutron-produced one, are also presented and the effects on the tritium release are discussed. (author)

  4. Hydrogen release from deposited beryllium layers

    Energy Technology Data Exchange (ETDEWEB)

    Shestakov, V.P.; Klepikov, A.Kh.; Chikhray, Y.V.; Tazhibaeva, I.L. [NIIETF of Al Farabi Kazakh State Univ., Almaty (Kazakhstan)

    2000-04-01

    The analysis of hydrogen retained in deposited beryllium layers deposited by magnetron sputtering was carried out by means of thermodesorption (TDS) technique. Two hydrogen release peaks were clearly seen on the thermodesorption curves at the temperatures 760-800 K and 920-970 K. Hydrogen concentrations in the deposited beryllium layers were calculated from the gas release curves corresponding to the number of Be atoms in the beryllium layer of 100% theoretical density. Average hydrogen concentration in the beryllium samples loaded in the process of magnetron sputtering was equal to 3800{+-}200 appm. The experiments with beryllium layers, enriched with carbon, revealed the increase of retained hydrogen concentration up to 9600{+-}200 appm. Assuming that gas release can be described within the framework of model of diffusion from layer system BeO-Be-BeO, hydrogen diffusion coefficient in BeO and the trapping and detrapping constants for the traps appearing in beryllium in the process of deposition were evaluated. (orig.)

  5. Characteristics of beryllium bonds; a QTAIM study.

    Science.gov (United States)

    Eskandari, K

    2012-08-01

    The nature of beryllium bonds formed between BeX2 (X is H, F and Cl) and some Lewis bases have been investigated. The distribution of the Laplacian of electron density shows that there is a region of charge depletion around the Be atom, which, according to Laplacian complementary principal, can interact with a region of charge concentration of an atom in the base and form a beryllium bond. The molecular graphs of the investigated complexes indicate that beryllium in BeH2 and BeF2 can form “beryllium bonds” with O, N and P atoms but not with halogens. In addition, eight criteria based on QTAIM properties, including the values of electron density and its Laplacian at the BCP, penetration of beryllium and acceptor atom, charge, energy, volume and first atomic moment of beryllium atom, have been considered and compared with the corresponding ones in conventional hydrogen bonds. These bonds share many common features with very strong hydrogen bonds, however,some differences have also been observed.

  6. Occupational Exposure to Beryllium. Final rule.

    Science.gov (United States)

    2017-01-09

    The Occupational Safety and Health Administration (OSHA) is amending its existing standards for occupational exposure to beryllium and beryllium compounds. OSHA has determined that employees exposed to beryllium at the previous permissible exposure limits face a significant risk of material impairment to their health. The evidence in the record for this rulemaking indicates that workers exposed to beryllium are at increased risk of developing chronic beryllium disease and lung cancer. This final rule establishes new permissible exposure limits of 0.2 micrograms of beryllium per cubic meter of air (0.2 [mu]g/m\\3\\) as an 8-hour time-weighted average and 2.0 [mu]g/m\\3\\ as a short-term exposure limit determined over a sampling period of 15 minutes. It also includes other provisions to protect employees, such as requirements for exposure assessment, methods for controlling exposure, respiratory protection, personal protective clothing and equipment, housekeeping, medical surveillance, hazard communication, and recordkeeping. OSHA is issuing three separate standards--for general industry, for shipyards, and for construction--in order to tailor requirements to the circumstances found in these sectors.

  7. Progress report on the behavior and modeling of copper alloy to stainless steel joints for ITER first wall applications

    Energy Technology Data Exchange (ETDEWEB)

    Min, J.; Stubbins, J.; Collins, J. [Univ. of Illinois, Urbana, IL (United States); Rowcliffe, A.F. [Oak Ridge National Lab., TN (United States)

    1998-09-01

    The stress states that lead to failure of joints between GlidCop{trademark} CuAl25 and 316L SS were examined using finite element modeling techniques to explain experimental observations of behavior of those joints. The joints were formed by hot isostatic pressing (HIP) and bend bar specimens were fabricated with the joint inclined 45{degree} to the major axis of the specimen. The lower surface of the bend bar was notched in order to help induce a precrack for subsequent loading in bending. The precrack was intended to localize a high stress concentration in close proximity to the interface so that its behavior could be examined without complicating factors from the bulk materials and the specimen configuration. Preparatory work to grow acceptable precracks caused the specimen to fail prematurely while the precrack was still progressing into the specimen toward the interface. This prompted the finite element model calculations to help understand the reasons for this behavior from examination of the stress states throughout the specimen. An additional benefit sought from the finite element modeling effort was to understand if the stress states in this non-conventional specimen were representative of those that might be experienced during operation in ITER.

  8. Sanitary-hygienic and ecological aspects of beryllium production

    Energy Technology Data Exchange (ETDEWEB)

    Dvinskykh, E.M.; Savchuk, V.V.; Sidorov, V.L.; Slobodin, D.B.; Tuzov, Y.V. [Ulba Metallurgical Plant, Ust-Kamenogorsk (Kazakhstan)

    1998-01-01

    The Report describes An organization of sanitary-hygienic and ecological control of beryllium production at Ulba metallurgical plant. It involves: (1) the consideration of main methods for protection of beryllium production personnel from unhealthy effect of beryllium, (2) main kinds of filters, used in gas purification systems at different process areas, (3) data on beryllium monitoring in water, soil, on equipment. This Report also outlines problems connected with designing devices for a rapid analysis of beryllium in air as well as problems of beryllium production on ecological situation in the town. (author)

  9. Status of the beryllium tile bonding qualification activities for the manufacturing of the ITER first wall

    Energy Technology Data Exchange (ETDEWEB)

    Mitteau, Raphaël, E-mail: Raphael.mitteau@iter.org [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Eaton, R.; Perez, G. [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Zacchia, F.; Banetta, S.; Bellin, B. [Fusion for Energy, Josep Pla 2, Torres Diagonal Litoral B3, 08019 Barcelona (Spain); Gervash, A.; Glazunov, D. [Efremov Research Institute, 189631 St. Petersburg (Russian Federation); Chen, J. [Southwestern Institute of Physics, Huangjing Road, Chengdu 610225 (China)

    2015-10-15

    The preparation of the manufacturing of the ITER first wall involves a qualification stage. The qualification aims at demonstrating that manufacturers can deliver the needed reliability and quality for the beryllium to copper bond, before the manufacturing can commence. The qualification is done on semi-prototype, containing relevant features relative to the beryllium armour (about 1/6 of the panel size). The qualification is done by the participating parties, firstly by a manufacturing semi-prototype and then by testing it under heat flux. One semi-prototype is manufactured and is being tested, and further from other manufacturers are still to come. The qualification programme is accompanied by bond defect investigations, which aim at defining defect acceptance criteria. Qualification and defect acceptance programme are supported by thermal and stress analyses, with good agreement regarding the thermal results, and some insights about the governing factors to bond damage.

  10. The effects of nucleation and solidification mechanisms on the microstructure and thermomechanical response of tin silver copper solder joints

    Science.gov (United States)

    Arfaei, Babak

    This work examines the nucleation mechanism of Sn in SnAgCu alloys and its effect on the microstructure of those solder joints. The nucleation rate of Sn in a SAC alloy was obtained by simultaneous calorimetric examination of the isothermal solidification of 88 flip chip Sn-Ag-Cu solder joints. Qualitative agreement with classic nucleation theory was observed, although it was concluded that the spherical cap model cannot be applied to explain the structure of nucleus. It was shown that the solidification temperature significantly affects the microstructure; samples that undercooled less than approximately 40oC revealed one or three large Sn grains, while interlaced twinning was observed in the samples that solidified at lower temperatures. In order to better understand the effect of microstructure on the thermomechanical properties of solder joints, a study of the dependence of room temperature shear fatigue lifetime on Sn grain number and orientation was conducted. This study examined the correlations of variations in fatigue life of solder balls with the microstructure of Sn-Ag-Cu solder. The mean fatigue lifetime was found to be significantly longer for samples with multiple Sn grains than for samples with single Sn grains. For single grain samples, correlations between Sn grain orientation (with respect to the loading direction) and lifetime were observed, providing insight on early failures in SnAgCu solder joints. Correlations between the lifetimes of single Sn grained, SAC205 solder joints with differences in Ag3Sn and Cu6Sn5 precipitate microstructures were investigated. It was found that Ag3Sn precipitates were highly segregated from Cu6Sn 5 precipitates on a length scale of approximately twenty microns. Furthermore, large (factor of two) variations of the Sn dendrite arm size were observed within given samples. Such variations in values of dendrite arm size within a single sample were much larger than observed variations of this parameter between

  11. Cu/Al真空扩散焊接头显微组织分析%Microstructure analyses in vacuum diffusion welded joint of copper and aluminum

    Institute of Scientific and Technical Information of China (English)

    李亚江; 吴会强; 陈茂爱; 杨敏; 冯涛

    2001-01-01

    采用真空扩散焊工艺方法,对Cu与Al扩散焊接头的组织性能进行了试验研究,利用扫描电镜(SEM)、电子探针(EPMA)、显微硬度等测试方法对焊接过渡区及基体组织和性能进行了分析。试验结果表明:采用真空扩散焊工艺,在加热温度520~540 ℃,保温时间60 min,压力11.5 MPa时,在Cu/Al界面处形成明显的扩散过渡区,扩散区域宽约40 μm。在铜侧过渡区中产生金属间化合物,会出现显微硬度高峰区,控制Al的扩散浓度可避免或减少界面处金属间化合物的产生。%By using vacuum diffusion welding process, the microstructures and performance of diffusion transition zone for the Cu/Al diffusion welding joint were researched by means of SEM, EPMA and micro-hardness test. The results indicate that under the condition of 520~540?℃ in holding time 60?min and pressure 11.5?MPa, the diffusion joined interface is obviously produced between copper and aluminum. The width of the diffusion interface zone is about 40?μm. The micro-hardness peak zone is formed in the copper side of the joined interface because of metal compounds such as γ and β phase. By controlling the Al diffusion amount, the brittle intermetallic compounds can be avoided or decreased.

  12. Mechanical performance of irradiated beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Scaffidi-Argentina, F.; Dalle-Donne, M.; Werle, H. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reaktortechnik

    1998-01-01

    For the Helium Cooled Pebble Bed (HCPB) Blanket, which is one of the two reference concepts studied within the European Fusion Technology Programme, the neutron multiplier consists of a mixed bed of about 2 and 0.1-0.2 mm diameter beryllium pebbles. Beryllium has no structural function in the blanket, however microstructural and mechanical properties are important, as they might influence the material behavior under neutron irradiation. The EXOTIC-7 as well as the `Beryllium` experiments carried out in the HFR reactor in Petten are considered as the most detailed and significant tests for investigating it. This paper reviews the present status of beryllium post-irradiation examinations performed at the Forschungszentrum Karlsruhe with samples from these irradiation experiments, emphasizing the effects of irradiation of essential material properties and trying to elucidate the processes controlling the property changes. The microstructure, the porosity distribution, the impurity content, the behavior under compression loads and the compatibility of the beryllium pebbles with lithium orthosilicate (Li{sub 4}SiO{sub 4}) during the in-pile irradiation are presented and critically discussed. Qualitative information on ductility and creep obtained by hardness-type measurements are also supplied. (author)

  13. Illness Absences Among Beryllium Sensitized Workers

    Science.gov (United States)

    Watkins, Janice P.; Ellis, Elizabeth D.; Girardi, David J.; Cragle, Donna L.

    2014-01-01

    Objectives. This study examined absence rates among US Department of Energy workers who had beryllium sensitization (BeS) or were diagnosed with chronic beryllium disease (CBD) compared with those of other workers. Methods. We used the lymphocyte proliferation test to determine beryllium sensitivity. In addition, we applied multivariable logistic regression to compare absences from 2002 to 2011 between workers with BeS or CBD to those without, and survival analysis to compare time to first absence by beryllium sensitization status. Finally, we examined beryllium status by occupational group. Results. Fewer than 3% of the 19 305 workers were BeS, and workers with BeS or CBD had more total absences (odds ratio [OR] = 1.31; 95% confidence interval [CI] = 1.18, 1.46) and respiratory absences (OR = 1.51; 95% CI = 1.24, 1.84) than did other workers. Time to first absence for all causes and for respiratory conditions occurred earlier for workers with BeS or CBD than for other workers. Line operators and crafts personnel were at increased risk for BeS or CBD. Conclusions. Although not considered “diseased,” workers with BeS have higher absenteeism compared with nonsensitized workers. PMID:25211750

  14. An official American Thoracic Society statement: diagnosis and management of beryllium sensitivity and chronic beryllium disease.

    Science.gov (United States)

    Balmes, John R; Abraham, Jerrold L; Dweik, Raed A; Fireman, Elizabeth; Fontenot, Andrew P; Maier, Lisa A; Muller-Quernheim, Joachim; Ostiguy, Gaston; Pepper, Lewis D; Saltini, Cesare; Schuler, Christine R; Takaro, Tim K; Wambach, Paul F

    2014-11-15

    Beryllium continues to have a wide range of industrial applications. Exposure to beryllium can lead to sensitization (BeS) and chronic beryllium disease (CBD). The purpose of this statement is to increase awareness and knowledge about beryllium exposure, BeS, and CBD. Evidence was identified by a search of MEDLINE. The committee then summarized the evidence, drew conclusions, and described their approach to diagnosis and management. The beryllium lymphocyte proliferation test is the cornerstone of both medical surveillance and the diagnosis of BeS and CBD. A confirmed abnormal beryllium lymphocyte proliferation test without evidence of lung disease is diagnostic of BeS. BeS with evidence of a granulomatous inflammatory response in the lung is diagnostic of CBD. The determinants of progression from BeS to CBD are uncertain, but higher exposures and the presence of a genetic variant in the HLA-DP β chain appear to increase the risk. Periodic evaluation of affected individuals can detect disease progression (from BeS to CBD, or from mild CBD to more severe CBD). Corticosteroid therapy is typically administered when a patient with CBD exhibits evidence of significant lung function abnormality or decline. Medical surveillance in workplaces that use beryllium-containing materials can identify individuals with BeS and at-risk groups of workers, which can help prioritize efforts to reduce inhalational and dermal exposures.

  15. Occupational and non-occupational allergic contact dermatitis from beryllium.

    Science.gov (United States)

    Vilaplana, J; Romaguera, C; Grimalt, F

    1992-05-01

    There are various references to sensitization to beryllium in the literature. Since introducing a patch testing series for patients with suspected sensitization to metals, we have found 3 cases of sensitization to beryllium. Of these 3 cases, we regard the first 2 as having relevant sensitization. Beryllium chloride (1% pet.) was positive in 3 patients and negative in 150 controls.

  16. 20 CFR 30.508 - What is beryllium sensitivity monitoring?

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false What is beryllium sensitivity monitoring? 30... and Offsets; Overpayments Payment of Claims and Offset for Certain Payments § 30.508 What is beryllium sensitivity monitoring? Beryllium sensitivity monitoring shall consist of medical examinations to confirm...

  17. Characteristics of beryllium exposure to small particles at a beryllium production facility.

    Science.gov (United States)

    Virji, M Abbas; Stefaniak, Aleksandr B; Day, Gregory A; Stanton, Marcia L; Kent, Michael S; Kreiss, Kathleen; Schuler, Christine R

    2011-01-01

    Epidemiological studies have reported process-specific elevated prevalence of beryllium sensitization (BeS) and chronic beryllium disease (CBD) among workers. However, exposure-response relationships have been inconsistent, possibly due to incomplete characterization of many biologically relevant aspects of exposure, including particle size. In 1999, two surveys were conducted 3-5 months apart at a beryllium metal, oxide, and alloy production facility during which personal impactor samples (n = 198) and personal 37-mm closed-face cassette (CFC) 'total' samples (n = 4026) were collected. Among process areas, median particle mass median aerodynamic diameter ranged from 5 to 14 μm. A large fraction of the beryllium aerosol was in the nonrespirable size range. Respirable beryllium concentrations were among the highest for oxide production [geometric mean (GM) = 2.02 μg m⁻³, geometric standard deviation (GSD) = 1.3] and pebbles plant (GM = 1.05 μg m⁻³, GSD = 2.9), areas historically associated with high risk of BeS and CBD. The relationship between GM 'CFC total' and GM respirable beryllium for jobs varied by process areas; the rank order of the jobs showed high overall consistency (Spearman r = 0.84), but the overall correlation was moderate (Pearson r = 0.43). Total beryllium concentrations varied greatly within and between workers among process areas; within-worker variance was larger than between-worker variance for most processes. A review of exposure characteristics among process areas revealed variation in chemical forms and solubility. Process areas with high risk of BeS and CBD had exposure to both soluble and insoluble forms of beryllium. Consideration of biologically relevant aspects of exposure such as beryllium particle size distribution, chemical form, and solubility will likely improve exposure assessment.

  18. Development of Beryllium-Copper Alloy Ignition Capsules

    Science.gov (United States)

    Cooley, Jason; Alexander, David; Thoma, Daniel; Field, Robert; Day, Robert; Cameron, Bernard; Nobile, Arthur; Rivera, Gerald; Kelly, Ann; Papin, Pallas; Schulze, Roland; Dauelsberg, Lawrence; Alexander, Neil; Galix, Remy

    2004-11-01

    Cu-doped Be capsules are being developed for ignition on the National Ignition Facility (NIF). Our fabrication approach is based on bonding of cylindrical parts containing precision machined hemispherical cavities, followed by machining an external spherical contour to produce a spherical shell. While we have demonstrated this approach, there are several key issues that need to be resolved before a shell meeting NIF specifications can be produced. These issues are synthesis of high purity small grain size Be0.9at%Cu alloy, formation of a strong hemishell bond that will allow the capsule to contain its 400 atm fill gas at room temperature, precision machining and polishing of the capsule to meet stringent specifications for surface finish and spherical quality, and filling with DT. In this paper we report on the progress that has been made in resolving these key issues.

  19. [Effects of beryllium chloride on cultured cells].

    Science.gov (United States)

    Sakaguchi, T; Sakaguchi, S; Nakamura, I; Kagami, M

    1984-05-01

    The effects of beryllium on cultured cells were investigated. Three cell-lines (HeLa-S3, Vero, HEL-R66) were used in these experiments and they were cultured in Eagle's MEM plus 5 or 10% FBS (Fetal Bovine Serum) containing beryllium in various concentrations. HeLa cells or Vero cells were able to grow in the medium with 10 micrograms Be/ml (1.1 mM). On the other hand, the growth of HEL cells were strongly inhibited, even when cultured in the medium with 1 microgram Be/ml (1.1 X 10(-1) mM) and the number of living cells showed markedly low level as compared to that of the control samples cultured in the medium without beryllium. The cytotoxic effects of beryllium on these cells, which were cultured for three days in the medium with beryllium, were observed. None of cytotoxic effects were found on HeLa cells cultured with 0.5 micrograms/ml (5.5 X 10(-2) mM) and on Vero cells cultured with 0.05 micrograms Be/ml (5.5 X 10(-3) mM), while HEL cells received cytotoxic effects even when cultured in the medium containing 0.05 micrograms Be/ml (5.5 X 10(-3) mM), and these effects on the cells appeared strong when cultured in the medium without FBS. It was revealed from these experiments that HEL cells are very sensitive in terms of toxic effects of beryllium. Therefore, there cells can be used for the toxicological study on low level concentrations of the metal.

  20. Mineral resource of the month: beryllium

    Science.gov (United States)

    Shedd, Kim B.

    2006-01-01

    Beryllium metal is lighter than aluminum and stiffer than steel. These and other properties, including its strength, dimensional stability, thermal properties and reflectivity, make it useful for aerospace and defense applications, such as satellite and space-vehicle structural components. Beryllium’s nuclear properties, combined with its low density, make it useful as a neutron reflector and moderator in nuclear reactors. Because it is transparent to most X rays, beryllium is used as X-ray windows in medical, industrial and analytical equipment.

  1. EFECTO DE LA ALTURA DEL MANGUITO EN UNIONES SOLDADAS EN CAÑERÍAS DE COBRE BUSHING HEIGHT EFFECT IN SOLDERED COPPER PIPE JOINTS

    Directory of Open Access Journals (Sweden)

    Víctor Carmona

    2006-12-01

    Full Text Available Se perforó un tubo de cobre de 28,6 mm de diámetro, por el proceso de taladrado por fluencia térmica (TFT. Se prepararon manguitos de diferentes alturas, haciendo un preperforado con brocas convencionales HSS de diferentes diámetros. Se seleccionaron manguitos de dos alturas diferentes. Se determinó la circularidad de la perforación. Se soldó un tubo cobre de ø 12,7 mm en forma perpendicular a un tubo de cobre de ø 28,6 mm y se determinó la resistencia a la tracción de la unión soldada, para lo cual se diseñó un dispositivo mecánico que fue adaptado en la máquina universal de ensayos. Se hicieron ensayos de microdureza y metalografía de la unión. Se concluyó que el manguito de menor altura es suficiente para que la unión alcance la máxima resistencia.Copper tubes were drilled with thermal flow drilling. Conventional HSS drills diameters were used to make pre drilling holes. Different height bushings were made. Two of the bushing heights were selected. The bushing circularity was measured. A ø 12,7 mm tube was welded perpendicularly on a ø 28,6 mm tube. A especial support device was designed and it was adapted to the Universal Test Machine, to determine the tensile stress of the brazing joint. The micro hardness and metallographic test were made in the brazing zone. As a conclusion the lower height bushing is enough to reach the maximum resistance.

  2. Cost effective aluminum beryllium mirrors for critical optics applications

    Science.gov (United States)

    Say, Carissa; Duich, Jack; Huskamp, Chris; White, Ray

    2013-09-01

    The unique performance of aluminum-beryllium frequently makes it an ideal material for manufacturing precision optical-grade metal mirrors. Traditional methods of manufacture utilize hot-pressed powder block in billet form which is subsequently machined to final dimensions. Complex component geometries such as lightweighted, non-plano mirrors require extensive tool path programming, fixturing, and CNC machining time and result in a high buy-to-fly ratio (the ratio of the mass of raw material purchased to the mass of the finished part). This increases the cost of the mirror structure as a significant percentage of the procurement cost is consumed in the form of machining, tooling, and scrap material that do not add value to the final part. Inrad Optics, Inc. and IBC Advanced Alloys Corp. undertook a joint study to evaluate the suitability of investment-cast Beralcast® 191 and 363 aluminum-beryllium as a precision mirror substrate material. Net shape investment castings of the desired geometry minimizes machining to just cleanup stock, thereby reducing the recurring procurement cost while still maintaining performance. The thermal stability of two mirrors, (one each of Beralcast® 191 and Beralcast® 363), was characterized from -40°F to +150°F. A representative pocketed mirror was developed, including the creation of a relevant geometry and production of a cast component to validate the approach. Information from the demonstration unit was used as a basis for a comparative cost study of the representative mirror produced in Beralcast® and one machined from a billet of AlBeMet® 162 (AlBeMet® is a registered trademark of Materion Corporation). The technical and financial results of these studies will be discussed in detail.

  3. Characterization of plasma sprayed beryllium ITER first wall mockups

    Energy Technology Data Exchange (ETDEWEB)

    Castro, R.G.; Vaidya, R.U.; Hollis, K.J. [Los Alamos National Lab., NM (United States). Material Science and Technology Div.

    1998-01-01

    ITER first wall beryllium mockups, which were fabricated by vacuum plasma spraying the beryllium armor, have survived 3000 thermal fatigue cycles at 1 MW/m{sup 2} without damage during high heat flux testing at the Plasma Materials Test Facility at Sandia National Laboratory in New Mexico. The thermal and mechanical properties of the plasma sprayed beryllium armor have been characterized. Results are reported on the chemical composition of the beryllium armor in the as-deposited condition, the through thickness and normal to the through thickness thermal conductivity and thermal expansion, the four-point bend flexure strength and edge-notch fracture toughness of the beryllium armor, the bond strength between the beryllium armor and the underlying heat sink material, and ultrasonic C-scans of the Be/heat sink interface. (author)

  4. Mechanisms of hydrogen retention in metallic beryllium and beryllium oxide and properties of ion-induced beryllium nitride; Rueckhaltemechanismen fuer Wasserstoff in metallischem Beryllium und Berylliumoxid sowie Eigenschaften von ioneninduziertem Berylliumnitrid

    Energy Technology Data Exchange (ETDEWEB)

    Oberkofler, Martin

    2011-09-22

    In the framework of this thesis laboratory experiments on atomically clean beryllium surfaces were performed. They aim at a basic understanding of the mechanisms occurring upon interaction of a fusion plasma with a beryllium first wall. The retention and the temperature dependent release of implanted deuterium ions are investigated. An atomistic description is developed through simulations and through the comparison with calculations based on density functional theory. The results of these investigations are compared to the behaviour of hydrogen upon implantation into thermally grown beryllium oxide layers. Furthermore, beryllium nitride is produced by implantation of nitrogen into metallic beryllium and its properties are investigated. The results are interpreted with regard to the use of beryllium in a fusion reactor. (orig.)

  5. Quantitative method of determining beryllium or a compound thereof in a sample

    Science.gov (United States)

    McCleskey, T. Mark; Ehler, Deborah S.; John, Kevin D.; Burrell, Anthony K.; Collis, Gavin E.; Minogue, Edel M.; Warner, Benjamin P.

    2010-08-24

    A method of determining beryllium or a beryllium compound thereof in a sample, includes providing a sample suspected of comprising beryllium or a compound thereof, extracting beryllium or a compound thereof from the sample by dissolving in a solution, adding a fluorescent indicator to the solution to thereby bind any beryllium or a compound thereof to the fluorescent indicator, and determining the presence or amount of any beryllium or a compound thereof in the sample by measuring fluorescence.

  6. Quantitative method of determining beryllium or a compound thereof in a sample

    Energy Technology Data Exchange (ETDEWEB)

    McCleskey, T. Mark (Los Alamos, NM); Ehler, Deborah S. (Los Alamos, NM); John, Kevin D. (Santa Fe, NM); Burrell, Anthony K. (Los Alamos, NM); Collis, Gavin E. (Los Alamos, NM); Minogue, Edel M. (Los Alamos, NM); Warner, Benjamin P. (Los Alamos, NM)

    2010-08-24

    A method of determining beryllium or a beryllium compound thereof in a sample, includes providing a sample suspected of comprising beryllium or a compound thereof, extracting beryllium or a compound thereof from the sample by dissolving in a solution, adding a fluorescent indicator to the solution to thereby bind any beryllium or a compound thereof to the fluorescent indicator, and determining the presence or amount of any beryllium or a compound thereof in the sample by measuring fluorescence.

  7. Quantitative method of determining beryllium or a compound thereof in a sample

    Energy Technology Data Exchange (ETDEWEB)

    McCleskey, T. Mark; Ehler, Deborah S.; John, Kevin D.; Burrell, Anthony K.; Collis, Gavin E.; Minogue, Edel M.; Warner, Benjamin P.

    2006-10-31

    A method of determining beryllium or a beryllium compound thereof in a sample, includes providing a sample suspected of comprising beryllium or a compound thereof, extracting beryllium or a compound thereof from the sample by dissolving in a solution, adding a fluorescent indicator to the solution to thereby bind any beryllium or a compound thereof to the fluorescent indicator, and determining the presence or amount of any beryllium or a compound thereof in the sample by measuring fluorescence.

  8. Electronic bistability in linear beryllium chains.

    Science.gov (United States)

    Helal, Wissam; Monari, Antonio; Evangelisti, Stefano; Leininger, Thierry

    2009-04-30

    A theoretical investigation on the mixed-valence behavior (bistability) of a series of cationic linear chains composed of beryllium atoms, Be(N)(+) (with N = 6,..., 12), is presented. The calculations were performed at CAS-SCF and MR-CI levels by using an ANO basis set containing 6s4p3d2f orbitals for each atom. Our results show a consistent gradual shift between different classes of mixed-valence compounds as the number of beryllium atoms increases, from class III strong coupling toward class II valence trapped. Indeed, in the largest cases (N > 10), the cationic chains were found to be closer to class I, where the coupling vanishes. The intramolecular electron transfer parameters V(ab), E(a), and E(opt) were calculated for each atomic chain. It is shown that the decrease of V(ab) with increasing N follows an exponential pattern.

  9. Plasma cleaning of beryllium coated mirrors

    Science.gov (United States)

    Moser, L.; Marot, L.; Steiner, R.; Newman, M.; Widdowson, A.; Ivanova, D.; Likonen, J.; Petersson, P.; Pintsuk, G.; Rubel, M.; Meyer, E.; Contributors, JET

    2016-02-01

    Cleaning systems of metallic first mirrors are needed in more than 20 optical diagnostic systems from ITER to avoid reflectivity losses. Currently, plasma sputtering is considered as one of the most promising techniques to remove deposits coming from the main wall (mainly beryllium and tungsten). This work presents the results of plasma cleaning of rhodium and molybdenum mirrors exposed in JET-ILW and contaminated with typical tokamak elements (including beryllium and tungsten). Using radio frequency (13.56 MHz) argon or helium plasma, the removal of mixed layers was demonstrated and mirror reflectivity improved towards initial values. The cleaning was evaluated by performing reflectivity measurements, scanning electron microscopy, x-ray photoelectron spectroscopy and ion beam analysis.

  10. PIGE analysis of magnesium and beryllium

    Science.gov (United States)

    Fonseca, M.; Jesus, A. P.; Luís, H.; Mateus, R.; Cruz, J.; Gasques, L.; Galaviz, D.; Ribeiro, J. P.

    2010-06-01

    In this work, we present an alternative method for PIGE analysis of magnesium and beryllium in thick samples. This method is based on the ERYA - Emitted Radiation Yield Analysis - code, which integrates the nuclear reaction excitation function along the depth of the sample. For this purpose, the excitations functions of the 25Mg(p,p'γ) 25Mg ( Eγ = 585 keV) and 9Be(p,γ) 10B ( Eγ = 718 keV) reactions were employed. Calculated gamma-ray yields were compared, at several proton energy values, with experimental yields for thick samples made of inorganic compounds containing magnesium or beryllium. The agreement is better than 5%. Taking into consideration the experimental uncertainty of the measured yields and the errors related to the stopping power values, this agreement shows that effects as the beam energy straggling, ignored in the calculation, seem to play a minor role.

  11. Neutron counter based on beryllium activation

    Energy Technology Data Exchange (ETDEWEB)

    Bienkowska, B.; Prokopowicz, R.; Kaczmarczyk, J.; Paducha, M. [Institute of Plasma Physics and Laser Microfusion (IPPLM), Hery 23, 01-497 Warsaw (Poland); Scholz, M.; Igielski, A. [Institute of Nuclear Physics PAS (IFJPAN), Radzikowskiego 152, 31-342 Krakow (Poland); Karpinski, L. [Faculty of Electrical Engineering, Rzeszow University of Technology, Pola 2, 35-959 Rzeszow (Poland); Pytel, K. [National Centre for Nuclear Research (NCBJ), Soltana 7, 05-400 Otwock - Swierk (Poland)

    2014-08-21

    The fusion reaction occurring in DD plasma is followed by emission of 2.45 MeV neutrons, which carry out information about fusion reaction rate and plasma parameters and properties as well. Neutron activation of beryllium has been chosen for detection of DD fusion neutrons. The cross-section for reaction {sup 9}Be(n, α){sup 6}He has a useful threshold near 1 MeV, which means that undesirable multiple-scattered neutrons do not undergo that reaction and therefore are not recorded. The product of the reaction, {sup 6}He, decays with half-life T{sub 1/2} = 0.807 s emitting β{sup −} particles which are easy to detect. Large area gas sealed proportional detector has been chosen as a counter of β–particles leaving activated beryllium plate. The plate with optimized dimensions adjoins the proportional counter entrance window. Such set-up is also equipped with appropriate electronic components and forms beryllium neutron activation counter. The neutron flux density on beryllium plate can be determined from the number of counts. The proper calibration procedure needs to be performed, therefore, to establish such relation. The measurements with the use of known β–source have been done. In order to determine the detector response function such experiment have been modeled by means of MCNP5–the Monte Carlo transport code. It allowed proper application of the results of transport calculations of β{sup −} particles emitted from radioactive {sup 6}He and reaching proportional detector active volume. In order to test the counter system and measuring procedure a number of experiments have been performed on PF devices. The experimental conditions have been simulated by means of MCNP5. The correctness of simulation outcome have been proved by measurements with known radioactive neutron source. The results of the DD fusion neutron measurements have been compared with other neutron diagnostics.

  12. Neutron counter based on beryllium activation

    Science.gov (United States)

    Bienkowska, B.; Prokopowicz, R.; Scholz, M.; Kaczmarczyk, J.; Igielski, A.; Karpinski, L.; Paducha, M.; Pytel, K.

    2014-08-01

    The fusion reaction occurring in DD plasma is followed by emission of 2.45 MeV neutrons, which carry out information about fusion reaction rate and plasma parameters and properties as well. Neutron activation of beryllium has been chosen for detection of DD fusion neutrons. The cross-section for reaction 9Be(n, α)6He has a useful threshold near 1 MeV, which means that undesirable multiple-scattered neutrons do not undergo that reaction and therefore are not recorded. The product of the reaction, 6He, decays with half-life T1/2 = 0.807 s emitting β- particles which are easy to detect. Large area gas sealed proportional detector has been chosen as a counter of β-particles leaving activated beryllium plate. The plate with optimized dimensions adjoins the proportional counter entrance window. Such set-up is also equipped with appropriate electronic components and forms beryllium neutron activation counter. The neutron flux density on beryllium plate can be determined from the number of counts. The proper calibration procedure needs to be performed, therefore, to establish such relation. The measurements with the use of known β-source have been done. In order to determine the detector response function such experiment have been modeled by means of MCNP5-the Monte Carlo transport code. It allowed proper application of the results of transport calculations of β- particles emitted from radioactive 6He and reaching proportional detector active volume. In order to test the counter system and measuring procedure a number of experiments have been performed on PF devices. The experimental conditions have been simulated by means of MCNP5. The correctness of simulation outcome have been proved by measurements with known radioactive neutron source. The results of the DD fusion neutron measurements have been compared with other neutron diagnostics.

  13. Beryllium induces premature senescence in human fibroblasts.

    Science.gov (United States)

    Coates, Shannon S A; Lehnert, Bruce E; Sharma, Sunil; Kindell, Susan M; Gary, Ronald K

    2007-07-01

    After cells have completed a sufficient number of cell divisions, they exit the cell cycle and enter replicative senescence. Here, we report that beryllium causes proliferation arrest with premature expression of the principal markers of senescence. After young presenescent human fibroblasts were treated with 3 microM BeSO(4) for 24 h, p21 cyclin-dependent kinase inhibitor mRNA increased by >200%. Longer periods of exposure caused mRNA and protein levels to increase for both p21 and p16(Ink4a), a senescence regulator that prevents pRb-mediated cell cycle progression. BeSO(4) also caused dose-dependent induction of senescence-associated beta-galactosidase activity (SA-beta-gal). Untreated cells had 48 relative fluorescence units (RFU)/microg/h of SA-beta-gal, whereas 3 microM BeSO(4) caused activity to increase to 84 RFU/microg/h. In chromatin immunoprecipitation experiments, BeSO(4) caused p53 protein to associate with its DNA binding site in the promoter region of the p21 gene, indicating that p53 transcriptional activity is responsible for the large increase in p21 mRNA elicited by beryllium. Forced expression of human telomerase reverse transcriptase (hTERT) rendered HFL-1 cells incapable of normal replicative senescence. However, there was no difference in the responsiveness of normal HFL-1 fibroblasts (IC(50) = 1.9 microM) and hTERT-immortalized cells (IC(50) = 1.7 microM) to BeSO(4) in a 9-day proliferation assay. The effects of beryllium resemble those of histone deacetylase-inhibiting drugs, which also cause large increases in p21. However, beryllium produced no changes in histone acetylation, suggesting that Be(2+) acts as a novel and potent pharmacological inducer of premature senescence.

  14. Computer simulation of electronic excitations in beryllium

    CERN Document Server

    Popov, A V

    2016-01-01

    An effective method for the quantitative description of the electronic excited states of polyatomic systems is developed by using computer technology. The proposed method allows calculating various properties of matter at the atomic level within the uniform scheme. A special attention is paid to the description of beryllium atoms interactions with the external fields, comparable by power to the fields in atoms, molecules and clusters.

  15. The bioinorganic chemistry and associated immunology of chronic beryllium disease.

    Science.gov (United States)

    Scott, Brian L; McCleskey, T Mark; Chaudhary, Anu; Hong-Geller, Elizabeth; Gnanakaran, S

    2008-07-07

    Chronic beryllium disease (CBD) is a debilitating, incurable, and often fatal disease that is caused by the inhalation of beryllium particulates. The growing use of beryllium in the modern world, in products ranging from computers to dental prosthetics (390 tons of beryllium in the US in the year 2000) necessitates a molecular based understanding of the disease in order to prevent and cure CBD. We have investigated the molecular basis of CBD at Los Alamos National Laboratory during the past six years, employing a multidisciplinary approach of bioinorganic chemistry and immunology. The results of this work, including speciation, inhalation and dissolution, and immunology will be discussed.

  16. The bioinorganic chemistry and associated immunology of chronic beryllium disease†

    Science.gov (United States)

    McCleskey, T. Mark; Chaudhary, Anu; Hong-Geller, Elizabeth; Gnanakaran, S.

    2013-01-01

    Chronic beryllium disease (CBD) is a debilitating, incurable, and often fatal disease that is caused by the inhalation of beryllium particulates. The growing use of beryllium in the modern world, in products ranging from computers to dental prosthetics (390 tons of beryllium in the US in the year 2000) necessitates a molecular based understanding of the disease in order to prevent and cure CBD. We have investigated the molecular basis of CBD at Los Alamos National Laboratory during the past six years, employing a multidisciplinary approach of bioinorganic chemistry and immunology. The results of this work, including speciation, inhalation and dissolution, and immunology will be discussed. PMID:18566702

  17. Possible health risks from low level exposure to beryllium.

    Science.gov (United States)

    Stange, A W; Hilmas, D E; Furman, F J

    1996-07-17

    The first case of chronic beryllium disease (CBD) at the Rocky Flats Environmental Technology Site (Rocky Flats) was diagnosed in a machinist in 1984. Rocky Flats, located 16 miles northwest of Denver, Colorado, is part of the United States Department of Energy (DOE) nuclear weapons complex. Research and development operations using beryllium began at Rocky Flats in 1953, and beryllium production operations began in 1957. Exposures could have occurred during foundry operations, casting, shearing, rolling, cutting, welding, machining, sanding, polishing, assembly, and chemical analysis operations. The Beryllium Health Surveillance Program (BHSP) was established in June 1991 at Rocky Flats to provide health surveillance for beryllium exposed employees using the Lymphocyte Proliferation Test (LPT) to identify sensitized individuals. Of the 29 cases of CBD and 76 cases of beryllium sensitization identified since 1991, several cases appear to have had only minimal opportunistic exposures to beryllium, since they were employed in administrative functions rather than primary beryllium operations. In conjunction with other health surveillance programs, a questionnaire and interview are administered to obtain detailed work and health histories. These histories, along with other data, are utilized to estimate the extent of an individual's exposure. Additional surveillance is in progress to attempt to characterize the possible risks from intermittent or brief exposures to beryllium in the workplace.

  18. Disposal of beryllium and cadmium from research reactors; Entsorgung von Beryllium und Cadmium aus Forschungsreaktoren

    Energy Technology Data Exchange (ETDEWEB)

    Lierse von Gostomski, C.; Remmert, A.; Stoewer, W. [Inst. fuer Radiochemie, Technische Univ. Muenchen, Garching (Germany); Bach, F.W.; Wilk, P.; Kutlu, I. [Inst. fuer Werkstoffkunde, Univ. Hannover, Hannover (Germany); Blenski, H.J.; Berthold, M. [Gesellschaft fuer Nuklear-Service mbH, Essen (Germany); Nerlich, K.D.; Plank, W. [TUeV Sueddeutschland Bau und Betrieb GmbH, Muenchen (Germany)

    2003-07-01

    Beryllium and cadmium mostly occur in metal form as radioactive special materials during the deconstruction of research reactors. Beryllium is usually used in these reactors as a neutron reflector and moderator, while cadmium is used above all as a neutron absorber. Both metals together have a high chemotoxicity as well as an inventory of radionuclides which has not been more closely characterised up to now. A high tritium content is to be expected, particularly in the case of beryllium; this tritium is due to the reaction of the metal with thermal reactor neutrons in particular. However, other nuclides which may be formed by neutron capture from impurities also contribute to the activity inventory. Up to now there is no qualified process for proper treatment, conditioning and intermediate and final repository in Germany. (orig.)

  19. Behavior of beryllium pebbles under irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Dalle-Donne, M.; Scaffidi-Argentina, F. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reactortechnik; Baldwin, D.L.; Gelles, D.S.; Greenwood, L.R.; Kawamura, H.; Oliver, B.M.

    1998-01-01

    Beryllium pebbles are being considered in fusion reactor blanket designs as neutron multiplier. An example is the European `Helium Cooled Pebble Bed Blanket.` Several forms of beryllium pebbles are commercially available but little is known about these forms in response to fast neutron irradiation. Commercially available beryllium pebbles have been irradiated to approximately 1.3 x 10{sup 22} n/cm{sup 2} (E>1 MeV) at 390degC. Pebbles 1-mm in diameter manufactured by Brush Wellman, USA and by Nippon Gaishi Company, Japan, and 3-mm pebbles manufactured by Brush Wellman were included. All were irradiated in the below-core area of the Experimental Breeder Reactor-II in Idaho Falls, USA, in molybdenum alloy capsules containing helium. Post-irradiation results are presented on density change measurements, tritium release by assay, stepped-temperature anneal, and thermal ramp desorption tests, and helium release by assay and stepped-temperature anneal measurements, for Be pebbles from two manufacturing methods, and with two specimen diameters. The experimental results on density change and tritium and helium release are compared with the predictions of the code ANFIBE. (author)

  20. Interactions of the organogold(III) compound Aubipyc with the copper chaperone Atox1: a joint mass spectrometry and circular dichroism investigation.

    Science.gov (United States)

    Marzo, Tiziano; Scaletti, Federica; Michelucci, Elena; Gabbiani, Chiara; Pescitelli, Gennaro; Messori, Luigi; Massai, Lara

    2015-12-01

    The so called "copper trafficking system" in mammalian cells is primarily devoted to the regulation of copper transport and homeostasis. This system, now well characterized, consists of a few strictly interconnected proteins that assist copper entrance inside cells and then promote metal transfer and delivery to essential copper-dependent cellular proteins (Boal and Rosenzweig 2009a; Banci et al., Mol Life Sci 67:2563-2589, 2010). Yet, the "copper trafficking system" may also facilitate the entrance inside cells of non-physiological metal species such as clinically established platinum drugs. ESI and MALDI MS methods are exploited here to characterize the interactions occurring between the experimental anticancer organogold(III) drug, Aubipyc, and the copper chaperone Atox1, a key protein of the copper trafficking system. The nature of the adducts that are formed when reacting Aubipyc with Atox1 is elucidated in detail. Characterization of the Aubipyc/Atox1 system is further supported by circular dichroism experiments. Binding competitions with mercury and bismuth ions were also explored. The relevance and the biological implications of the present results are discussed.

  1. Functionally Graded Nanophase Beryllium/Carbon Composites

    Science.gov (United States)

    Choi, Michael K.

    2003-01-01

    Beryllium, beryllium alloys, beryllium carbide, and carbon are the ingredients of a class of nanophase Be/Be2C/C composite materials that can be formulated and functionally graded to suit a variety of applications. In a typical case, such a composite consists of a first layer of either pure beryllium or a beryllium alloy, a second layer of B2C, and a third layer of nanophase sintered carbon derived from fullerenes and nanotubes. The three layers are interconnected through interpenetrating spongelike structures. These Be/Be2C/C composite materials are similar to Co/WC/diamond functionally graded composite materials, except that (1) W and Co are replaced by Be and alloys thereof and (2) diamond is replaced by sintered carbon derived from fullerenes and nanotubes. (Optionally, one could form a Be/Be2C/diamond composite.) Because Be is lighter than W and Co, the present Be/Be2C/C composites weigh less than do the corresponding Co/WC/diamond composites. The nanophase carbon is almost as hard as diamond. WC/Co is the toughest material. It is widely used for drilling, digging, and machining. However, the fact that W is a heavy element (that is, has high atomic mass and mass density) makes W unattractive for applications in which weight is a severe disadvantage. Be is the lightest tough element, but its toughness is less than that of WC/Co alloy. Be strengthened by nanophase carbon is much tougher than pure or alloy Be. The nanophase carbon has an unsurpassed strength-to-weight ratio. The Be/Be2C/C composite materials are especially attractive for terrestrial and aerospace applications in which there are requirements for light weight along with the high strength and toughness of the denser Co/WC/diamond materials. These materials could be incorporated into diverse components, including cutting tools, bearings, rocket nozzles, and shields. Moreover, because Be and C are effective as neutron moderators, Be/Be2C/C composites could be attractive for some nuclear applications.

  2. Beryllium metal II. a review of the available toxicity data.

    Science.gov (United States)

    Strupp, Christian

    2011-01-01

    Beryllium metal was classified in Europe collectively with beryllium compounds, e.g. soluble salts. Toxicological equivalence was assumed despite greatly differing physicochemical properties. Following introduction of the Registration, Evaluation, Authorization and Restriction of Chemicals (REACH) regulation, beryllium metal was classified as individual substance and more investigational efforts to appropriately characterize beryllium metal as a specific substance apart from soluble beryllium compounds was required. A literature search on toxicity of beryllium metal was conducted, and the resulting literature compiled together with the results of a recently performed study package into a comprehensive data set. Testing performed under Organisation for Economic Co-Operation and Development guidelines and Good Laboratory Practice concluded that beryllium metal was neither a skin irritant, an eye irritant, a skin sensitizer nor evoked any clinical signs of acute oral toxicity; discrepancies between the current legal classification of beryllium metal in the European Union (EU) and the experimental results were identified. Furthermore, genotoxicity and carcinogenicity were discussed in the context of the literature data and the new experimental data. It was concluded that beryllium metal is unlikely to be a classical nonthreshold mutagen. Effects on DNA repair and morphological cell transformation were observed but need further investigation to evaluate their relevance in vivo. Animal carcinogenicity studies deliver evidence of carcinogenicity in the rat; however, lung overload may be a species-specific confounding factor in the existing studies, and studies in other species do not give convincing evidence of carcinogenicity. Epidemiology has been intensively discussed over the last years and has the problem that the studies base on the same US beryllium production population and do not distinguish between metal and soluble compounds. It is noted that the correlation

  3. Deuterium/hydrogen isotope exchange on beryllium and beryllium nitride; Deuterium/Wasserstoff-Isotopenaustausch an Beryllium und Berylliumnitrid

    Energy Technology Data Exchange (ETDEWEB)

    Dollase, Petra; Eichler, Michael; Koeppen, Martin; Dittmar, Timo; Linsmeier, Christian [Forschungszentrum Juelich GmbH, Institut fuer Energie- und Klimaforschung - Plasmaphysik (Germany)

    2016-07-01

    In the fusion experiments JET and ITER, the first wall is made up of beryllium. The use of nitrogen is discussed for radiative cooling in the divertor. This can react with the surface of the first wall to form beryllium nitride (Be{sub 3}N{sub 2}). The hydrogen isotopes deuterium and tritium, which react in the fusion reaction to helium and a neutron, are used as fuel. Since the magnetic confinement of the plasma is not perfect, deuterium and tritium ions are also found on the beryllium wall and can accumulate there. This should be avoided due to the radioactivity of tritium. Therefore the isotope exchange with deuterium is investigated to regenerate the first wall. We investigate the isotopic exchange of deuterium and protium in order to have not to work with radioactive tritium. The ion bombardment is simulated with an ion source. With voltages up to a maximum of 5 kV, deuterium and protic hydrogen ions are implanted in polycrystalline Be and Be{sub 3}N{sub 2}. The samples are then analyzed in situ using X-ray photoelectron spectroscopy (XPS) and thermal desorption spectroscopy (TDS). Subsequently, samples prepared under the same conditions are characterized ex-situ by means of nuclear reaction analysis (NRA). [German] In den Fusionsexperimenten JET und ITER besteht die erste Wand im Hauptraum aus Beryllium (Be). Zur Strahlungskuehlung im Divertor wird der Einsatz von Stickstoff diskutiert. Dieser kann mit der Oberflaeche der ersten Wand zu Berylliumnitrid (Be{sub 3}N{sub 2}) reagieren. Als Brennstoff werden die Wasserstoffisotope Deuterium und Tritium eingesetzt, die in der Fusionsreaktion zu Helium und einem Neutron reagieren. Da der magnetische Einschluss des Plasmas nicht perfekt ist, treffen auch Deuterium- und Tritiumionen auf die Berylliumwand auf und koennen sich dort anreichern. Das soll aufgrund der Radioaktivitaet von Tritium unbedingt vermieden werden. Daher wird zur Regenerierung der ersten Wand der Isotopenaustausch mit Deuterium untersucht. Wir

  4. Beryllium toxicity testing in the suspension culture of mouse fibroblasts.

    Science.gov (United States)

    Rössner, P; Bencko, V

    1980-01-01

    Suspension culture of mouse fibroblast cell line L-A 115 was used to test beryllium toxicity in the presence of magnesium ions. Beryllium added to the MEM cultivation medium was bound in a complex with sulphosalicylic acid BeSSA complex, because the use of beryllium chloride turned out to yield ineffective beryllium phosphate that formed macroscopically detectable insoluble opacities. The BeSSA complex was used in the concentration range: 10(-3)--10(-9)M, magnesium was used in 3 concentrations: 10(-1)M, 5 x 10(-2)M and 10(-2)M. Growth curve analysis revealed pronounced beryllium toxicity at the concentration of 10(-3)M, magnesium-produced toxic changes were observed only at the concentration of 10(-1)M. No competition between the beryllium and magnesium ions was recorded. It is assumed that the possible beryllium-magnesium competition was significantly modified by the use of BeSSA complex-bound beryllium.

  5. 10 CFR 850.20 - Baseline beryllium inventory.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Baseline beryllium inventory. 850.20 Section 850.20 Energy... Baseline beryllium inventory. (a) The responsible employer must develop a baseline inventory of the... inventory, the responsible employer must: (1) Review current and historical records; (2) Interview...

  6. Ionization energies of beryllium in strong magnetic fields

    Institute of Scientific and Technical Information of China (English)

    GUANXiao-xu; ZHANGYue-xia

    2004-01-01

    We have develop an effective frozen core approximation to calculate energy levels and ionization enegies of the beryllium atom in magnetic field strengths up to 2.35 × 105T. Systematic improvement over the Hartree-Fock results for the beryllium low-lying states has been accomplished.

  7. Ionization energies of beryllium in strong magnetic fields

    Institute of Scientific and Technical Information of China (English)

    GUAN Xiao-xu; ZHANG Yue-xia

    2004-01-01

    We have develop an effective frozen core approximation to calculate energy levels and ionization enegies of the beryllium atom in magnetic field strengths up to 2.35×105T. Systematic improvement over the Hartree-Fock results for the beryllium low-lying states has been accomplished.

  8. IRIS TOXICOLOGICAL REVIEW AND SUMMARY DOCUMENTS FOR BERYLLIUM AND COMPOUNDS

    Science.gov (United States)

    EPA's assessment of the noncancer health effects and carcinogenic potential of Beryllium was added to the IRIS database in 1998. The IRIS program is updating the IRIS assessment for Beryllium. This update will incorporate health effects information published since the last assess...

  9. Failure Assessment Diagram for Titanium Brazed Joints

    Science.gov (United States)

    Flom, Yury; Jones, Justin S.; Powell, Mollie M.; Puckett, David F.

    2011-01-01

    The interaction equation was used to predict failure in Ti-4V-6Al joints brazed with Al 1100 filler metal. The joints used in this study were geometrically similar to the joints in the brazed beryllium metering structure considered for the ATLAS telescope. This study confirmed that the interaction equation R(sub sigma) + R(sub Tau) = 1, where R(sub sigma) and R(sub Tau)are normal and shear stress ratios, can be used as conservative lower bound estimate of the failure criterion in ATLAS brazed joints as well as for construction of the Failure Assessment Diagram (FAD).

  10. Toxicological effects of beryllium on platelets and vascular endothelium.

    Science.gov (United States)

    Togna, G; Togna, A R; Russo, P; Caprino, L

    1997-06-01

    Although ample research has described the toxic effects of the metal beryllium on the respiratory apparatus, less is known about its effects on the vascular apparatus, including pulmonary blood vessels. We investigated the in vitro effects of beryllium on endothelial vascular adenosine diphosphatase activity and prostacyclin production in bovine aortic endothelium, and on nitric oxide release in isolated rabbit arteries. Rabbit and human platelet responsiveness was also evaluated. Beryllium inhibited vascular endothelial adenosine diphosphatase activity, prostacyclin production, and nitric oxide release, thus inducing functional alterations in vascular endothelial cells. It also induced platelet hyperreactivity to arachidonic acid, as shown by a lowering of the threshold of aggregating concentration and by concurrently increasing thromboxane production. In contrast, beryllium left the response to aggregating and nonaggregating concentrations of ADP and collagen unchanged. These findings show that beryllium may impair some vascular endothelial functions and alter the interaction between platelet and endothelial mediators.

  11. Protection of air in premises and environment against beryllium aerosols

    Energy Technology Data Exchange (ETDEWEB)

    Bitkolov, N.Z.; Vishnevsky, E.P.; Krupkin, A.V. [Research Inst. of Industrial and Marine Medicine, St. Petersburg (Russian Federation)

    1998-01-01

    First and foremost, the danger of beryllium aerosols concerns a possibility of their inhalation. The situation is aggravated with high biological activity of the beryllium in a human lung. The small allowable beryllium aerosols` concentration in air poses a rather complex and expensive problem of the pollution prevention and clearing up of air. The delivery and transportation of beryllium aerosols from sites of their formation are defined by the circuit of ventilation, that forms aerodynamics of air flows in premises, and aerodynamic links between premises. The causes of aerosols release in air of premises from hoods, isolated and hermetically sealed vessels can be vibrations, as well as pulses of temperature and pressure. Furthermore, it is possible the redispersion of aerosols from dirty surfaces. The effective protection of air against beryllium aerosols at industrial plants is provided by a complex of hygienic measures: from individual means of breath protection up to collective means of the prevention of air pollution. (J.P.N.)

  12. Estimating occupational beryllium exposure from compliance monitoring data.

    Science.gov (United States)

    Hamm, Michele P; Burstyn, Igor

    2011-01-01

    Occupational exposure to beryllium is widespread and is a health risk. The objectives of this study were to develop plausible models to estimate occupational airborne beryllium exposure. Compliance monitoring data were obtained from the Occupational Safety and Health Administration for 12,148 personal measurements of beryllium exposure from 1979 to 2005. Industry codes were maintained as reported or collapsed based on the number of measurements per cell of a job-exposure matrix (JEM). Probability of exposure was predicted based on year, industry, job, and sampling duration. In these models, probability of exposure decreased over time, was highest in full-shift personal samples, and varied with industry and job. The probability of exposure was calculated using 6 JEMs, each providing similar rankings of the likelihood of non-negligible exposure to beryllium. These statistical models, with expert appraisal, are suitable for the assessment of the probability of elevated occupational exposure to beryllium.

  13. Release of beryllium into artificial airway epithelial lining fluid.

    Science.gov (United States)

    Stefaniak, Aleksandr B; Virji, M Abbas; Day, Gregory A

    2012-01-01

    Inhaled beryllium particles that deposit in the lung airway lining fluid may dissolve and interact with immune-competent cells resulting in sensitization. As such, solubilization of 17 beryllium-containing materials (ore, hydroxide, metal, oxide, alloys, and process intermediates) was investigated using artificial human airway epithelial lining fluid. The maximum beryllium release in 7 days was 11.78% (from a beryl ore melter dust), although release from most materials was beryllium ions may be released in the respiratory tract via dissolution in airway lining fluid. Beryllium-containing particles that deposit in the respiratory tract dissolve in artificial lung epithelial lining fluid, thereby providing ions for absorption in the lung and interaction with immune-competent cells in the respiratory tract.

  14. ZIRCONIUM-TITANIUM-BERYLLIUM BRAZING ALLOY

    Science.gov (United States)

    Gilliland, R.G.; Patriarca, P.; Slaughter, G.M.; Williams, L.C.

    1962-06-12

    A new and improved ternary alloy is described which is of particular utility in braze-bonding parts made of a refractory metal selected from Group IV, V, and VI of the periodic table and alloys containing said metal as a predominating alloying ingredient. The brazing alloy contains, by weight, 40 to 50 per cent zirconium, 40 to 50 per cent titanium, and the balance beryllium in amounts ranging from 1 to 20 per cent, said alloy having a melting point in the range 950 to 1400 deg C. (AEC)

  15. Plasma transferred arc deposition of beryllium

    Science.gov (United States)

    Hollis, K.; Bartram, B.; Withers, J.; Storm, R.; Massarello, J.

    2006-12-01

    The exceptional properties of beryllium (Be), including low density and high elastic modulus, make it the material of choice in many defense and aerospace applications. However, health hazards associated with Be material handling limit the applications that are suited for its use. Innovative solutions that enable continued use of Be in critical applications while addressing worker health concerns are highly desirable. Plasma transferred arc solid free-form fabrication is being evaluated as a Be fabrication technique for civilian and military space-based components. Initial experiments producing Be deposits are reported here. Deposit shape, microstructure, and mechanical properties are reported.

  16. Neutron beams from protons on beryllium.

    Science.gov (United States)

    Bewley, D K; Meulders, J P; Octave-Prignot, M; Page, B C

    1980-09-01

    Measurements of dose rate and penetration in water have been made for neutron beams produced by 30--75 MeV protons on beryllium. The effects of Polythene filters added on the target side of the collimator have also been studied. A neutron beam comparable with a photon beam from a 4--8 MeV linear accelerator can be produced with p/Be neutrons plus 5 cm Polythene filtrations, with protons in the range 50--75 MeV. This is a more economical method than use of the d/Be reaction.

  17. 40 CFR 63.11166 - What General Provisions apply to primary beryllium production facilities?

    Science.gov (United States)

    2010-07-01

    ... primary beryllium production facilities? 63.11166 Section 63.11166 Protection of Environment ENVIRONMENTAL... Primary Nonferrous Metals Area Sources-Zinc, Cadmium, and Beryllium Primary Beryllium Production Facilities § 63.11166 What General Provisions apply to primary beryllium production facilities? (a) You...

  18. Fluorimetric method for determination of Beryllium; Determinazione fluorimetrica del berillio

    Energy Technology Data Exchange (ETDEWEB)

    Sparacino, N.; Sabbioneda, S. [ENEA, Centro Ricerche Saluggia, Vercelli (Italy). Dip. Energia

    1996-10-01

    The old fluorimetric method for the determination of Beryllium, based essentially on the fluorescence of the Beryllium-Morine complex in a strongly alkaline solution, is still competitive and stands the comparison with more modern methods or at least three reasons: in the presence of solid or gaseous samples (powders), the times necessary to finalize an analytic determination are comparable since the stage of the process which lasts the longest is the mineralization of the solid particles containing Beryllium, the cost of a good fluorimeter is by far Inferior to the cost, e. g., of an Emission Spectrophotometer provided with ICP torch and magnets for exploiting the Zeeman effect and of an Atomic absorption Spectrophotometer provided with Graphite furnace; it is possible to determine, fluorimetrically, rather small Beryllium levels (about 30 ng of Beryllium/sample), this potentiality is more than sufficient to guarantee the respect of all the work safety and hygiene rules now in force. The study which is the subject of this publication is designed to the analysis procedure which allows one to reach good results in the determination of Beryllium, chiefly through the control and measurement of the interference effect due to the presence of some metals which might accompany the environmental samples of workshops and laboratories where Beryllium is handled, either at the pure state or in its alloys. The results obtained satisfactorily point out the merits and limits of this analytic procedure.

  19. Beryllium nitrate inhibits fibroblast migration to disrupt epimorphic regeneration.

    Science.gov (United States)

    Cook, Adam B; Seifert, Ashley W

    2016-10-01

    Epimorphic regeneration proceeds with or without formation of a blastema, as observed for the limb and skin, respectively. Inhibition of epimorphic regeneration provides a means to interrogate the cellular and molecular mechanisms that regulate it. In this study, we show that exposing amputated limbs to beryllium nitrate disrupts blastema formation and causes severe patterning defects in limb regeneration. In contrast, exposing full-thickness skin wounds to beryllium only causes a delay in skin regeneration. By transplanting full-thickness skin from ubiquitous GFP-expressing axolotls to wild-type hosts, we demonstrate that beryllium inhibits fibroblast migration during limb and skin regeneration in vivo Moreover, we show that beryllium also inhibits cell migration in vitro using axolotl and human fibroblasts. Interestingly, beryllium did not act as an immunostimulatory agent as it does in Anurans and mammals, nor did it affect keratinocyte migration, proliferation or re-epithelialization, suggesting that the effect of beryllium is cell type-specific. While we did not detect an increase in cell death during regeneration in response to beryllium, it did disrupt cell proliferation in mesenchymal cells. Taken together, our data show that normal blastema organogenesis cannot occur without timely infiltration of local fibroblasts and highlights the importance of positional information to instruct pattern formation during regeneration. In contrast, non-blastemal-based skin regeneration can occur despite early inhibition of fibroblast migration and cell proliferation.

  20. Quantum molecular dynamics simulations of beryllium at high pressures

    Science.gov (United States)

    Desjarlais, Michael; Knudson, Marcus

    2008-03-01

    The phase boundaries and high pressure melt properties of beryllium have been the subject of several recent experimental and theoretical studies. The interest is motivated in part by the use of beryllium as an ablator material in inertial confinement fusion capsule designs. In this work, the high pressure melt curve, Hugoniot crossings, sound speeds, and phase boundaries of beryllium are explored with DFT based quantum molecular dynamics calculations. The entropy differences between the various phases of beryllium are extracted in the vicinity of the melt curve and agree favorably with earlier theoretical work on normal melting. High velocity flyer plate experiments with beryllium targets on Sandia's Z machine have generated high quality data for the Hugoniot, bulk sound speeds, and longitudinal sound speeds. This data provides a tight constraint on the pressure for the onset of shock melting of beryllium and intriguing information on the solid phase prior to melt. The results of the QMD calculations and the experimental results will be compared, and implications for the HCP and BCC phase boundaries of beryllium will be presented.

  1. Sarcoidosis and chronic beryllium disease: similarities and differences.

    Science.gov (United States)

    Mayer, Annyce S; Hamzeh, Nabeel; Maier, Lisa A

    2014-06-01

    Chronic beryllium disease (CBD) is a granulomatous lung disease that may be pathologically and clinically indistinguishable from pulmonary sarcoidosis, except through use of immunologic testing, such as the beryllium lymphocyte proliferation test (BeLPT). Similar to sarcoidosis, the pulmonary manifestations of CBD are variable and overlap with other respiratory diseases. Definitive diagnosis of CBD is established by evidence of immune sensitization to beryllium and diagnostic bronchoscopy with bronchoalveolar lavage and transbronchial biopsy. However, the diagnosis of CBD can also be established on a medically probable basis in beryllium-exposed patients with consistent radiographic imaging and clinical course. Beryllium workers exposed too much higher levels of beryllium in the past demonstrated a much more fulminant disease than is usually seen today. Some extrapulmonary manifestations similar to sarcoidosis were noted in these historic cohorts, although with a narrower spectrum. Extrapulmonary manifestations of CBD are rare today. Since lung-predominant sarcoidosis can very closely resemble CBD, CBD is still misdiagnosed as sarcoidosis when current or past exposure to beryllium is not recognized and no BeLPT is obtained. This article describes the similarities and differences between CBD and sarcoidosis, including clinical and diagnostic features that can help physicians consider CBD in patients with apparent lung-predominant sarcoidosis.

  2. Angiotensin-1 converting enzyme polymorphisms in chronic beryllium disease.

    Science.gov (United States)

    Maier, L A; Raynolds, M V; Young, D A; Barker, E A; Newman, L S

    1999-04-01

    To test the hypothesis that the angiotensin converting enzyme (ACE) genotype is associated with chronic beryllium disease (CBD) and disease severity, we studied 50 cases of CBD and compared their ACE genotype to that of two different control groups, consisting of: (1) 50 participants from a beryllium machining facility; and (2) 50 participants from a non-beryllium-associated workplace. We found no statistically significant difference in the frequency of the I or D allele or of the DD genotype among cases of CBD and either control group. The odds ratio (OR) for the CBD DD genotype as compared with the non-DD genotype was 1.58 (95% confidence interval [CI]: 0.68 to 3.66, p = 0.12) for the beryllium-exposed control group, and 1.09 (95% CI: 0.48 to 2.46, p = 0.56) for the non-beryllium-exposed controls. We found an association between serum ACE activity and the ACE genotype, with DD cases having the highest median serum ACE activity (p = 0.005). We evaluated the beryllium lymphocyte proliferation test (BeLPT), bronchoalveolar lavage (BAL) cell components, chest radiography, pulmonary function test results, and exercise physiology in our CBD cases. No statistically significant associations with these disease markers were found for the CBD cases with the DD genotype. Although the difference was not statistically significant, the DD cases had a shorter median duration of exposure to beryllium before diagnosis of CBD, and tended to have a weaker response in their blood and BAL BeLPT than did the non-DD cases. These findings may indicate that the ACE genotype is important in the immune response to beryllium and in progression to beryllium disease.

  3. Detection and investigation of the molecular nature of low-molecular-mass copper ions in isolated rheumatoid knee-joint synovial fluid.

    Science.gov (United States)

    Naughton, D P; Knappitt, J; Fairburn, K; Gaffney, K; Blake, D R; Grootveld, M

    1995-03-20

    Low-molecular-mass copper(II) species have been detected and quantified in ultrafiltrates (n = 7) of rheumatoid synovial fluid (SF) by a highly-sensitive HPLC-based assay system with the ability to determine Cu(II) concentrations of ultrafiltrates resulted in complexation by histidine > alanine > formate > threonine > lactate > tyrosine > phenylalanine, their effectiveness in this context being in the given order. CD spectra of Cu(II)-treated samples of intact SF exhibited absorption bands typical of copper(II)-albumin complexes, in addition to a band attributable to a low-molecular-mass histidinate complex (lambda min 610 nm). Since both albumin and histidine are potent radical scavengers, these results indicate that any .OH radical generated from bound copper ions will be 'site-specifically' scavenged. Hence, low-molecular-mass copper complexes with the ability to promote the generation of .OH radical which can then escape from the metal ion co-ordination sphere (and in turn, cause damage to critical biomolecules) appear to be absent from inflammatory SF.

  4. Inhibitory effects of beryllium chloride on rat liver microsomal enzymes.

    Science.gov (United States)

    Teixeira, C F; Yasaka, W J; Silva, L F; Oshiro, T T; Oga, S

    1990-04-30

    A single i.v. dose (0.1 mmol Be2+/kg) of beryllium chloride prolonged the duration of pentobarbital-induced sleep and zoxazolamine-induced paralysis, in rats. The effects are correlated with changes of the pharmacokinetic parameters and with the in vitro inhibition of both aliphatic and aromatic hydroxylation of pentobarbital and zoxazolamine. In vitro N-demethylation of meperidine and aminopyrine was partially inhibited while O-demethylation of quinidine was unaffected by liver microsomes of rats pretreated with beryllium salt. The findings give clues that beryllium chloride inhibits some forms of cytochrome P-450, especially those responsible for hydroxylation of substrates, like pentobarbital and zoxazolamine.

  5. Beryllium Health and Safety Committee Data Reporting Task Force

    Energy Technology Data Exchange (ETDEWEB)

    MacQueen, D H

    2007-02-21

    On December 8, 1999, the Department of Energy (DOE) published Title 10 CFR 850 (hereafter referred to as the Rule) to establish a chronic beryllium disease prevention program (CBDPP) to: {sm_bullet} reduce the number of workers currently exposed to beryllium in the course of their work at DOE facilities managed by DOE or its contractors, {sm_bullet} minimize the levels of, and potential for, expos exposure to beryllium, and {sm_bullet} establish medical surveillance requirements to ensure early detection of the disease.

  6. Development of Beryllium Vacuum Chamber Technology for the LHC

    CERN Document Server

    Veness, R; Dorn, C

    2011-01-01

    Beryllium is the material of choice for the beam vacuum chambers around collision points in particle colliders due to a combination of transparency to particles, high specific stiffness and compatibility with ultra-high vacuum. New requirements for these chambers in the LHC experiments have driven the development of new methods for the manufacture of beryllium chambers. This paper reviews the requirements for experimental vacuum chambers. It describes the new beryllium technology adopted for the LHC and experience gained in the manufacture and installation.

  7. Measurement of Beryllium in Biological Samples by Accelerator Mass Spectrometry: Applications for Studying Chronic Beryllium Disease

    Energy Technology Data Exchange (ETDEWEB)

    Chiarappa-Zucca, M L; Finkel, R C; Martinelli, R E; McAninch, J E; Nelson, D O; Turtletaub, K W

    2004-04-15

    A method using accelerator mass spectrometry (AMS) has been developed for quantifying attomoles of beryllium (Be) in biological samples. This method provides the sensitivity to trace Be in biological samples at very low doses with the purpose of identifying the molecular targets involved in chronic beryllium disease. Proof of the method was tested by administering 0.001, 0.05, 0.5 and 5.0 {micro}g {sup 9}Be and {sup 10}Be by intraperitoneal injection to male mice and removing spleen, liver, femurs, blood, lung, and kidneys after 24 h exposure. These samples were prepared for AMS analysis by tissue digestion in nitric acid, followed by further organic oxidation with hydrogen peroxide and ammonium persulfate and lastly, precipitation of Be with ammonium hydroxide, and conversion to beryllium oxide at 800 C. The {sup 10}Be/{sup 9}Be ratio of the extracted beryllium oxide was measured by AMS and Be in the original sample was calculated. Results indicate that Be levels were dose-dependent in all tissues and the highest levels were measured in the spleen and liver. The measured {sup 10}Be/{sup 9}Be ratios spanned 4 orders of magnitude, from 10{sup -10} to 10{sup -14}, with a detection limit of 3.0 x 10{sup -14}, which is equivalent to 0.8 attomoles of {sup 10}Be. These results show that routine quantification of nanogram levels of Be in tissues is possible and that AMS is a sensitive method that can be used in biological studies to understand the molecular dosimetry of Be and mechanisms of toxicity.

  8. Extraction of beryllium from refractory beryllium oxide with dilute ammonium bifluoride and determination by fluorescence: a multiparameter performance evaluation.

    Science.gov (United States)

    Goldcamp, Michael J; Goldcamp, Diane M; Ashley, Kevin; Fernback, Joseph E; Agrawal, Anoop; Millson, Mark; Marlow, David; Harrison, Kenneth

    2009-12-01

    Beryllium exposure can cause a number of deleterious health effects, including beryllium sensitization and the potentially fatal chronic beryllium disease. Efficient methods for monitoring beryllium contamination in workplaces are valuable to help prevent dangerous exposures to this element. In this work, performance data on the extraction of beryllium from various size fractions of high-fired beryllium oxide (BeO) particles (from Beryllium concentrations were determined by fluorescence using a hydroxybenzoquinoline fluorophore. The effects of ABF concentration and volume, extraction temperature, sample tube types, and presence of filter or wipe media were examined. Three percent ABF extracts beryllium nearly twice as quickly as 1% ABF; extraction solution volume has minimal influence. Elevated temperatures increase the rate of extraction dramatically compared with room temperature extraction. Sample tubes with constricted tips yield poor extraction rates owing to the inability of the extraction medium to access the undissolved particles. The relative rates of extraction of Be from BeO of varying particle sizes were examined. Beryllium from BeO particles in fractions ranging from less than 32 microm up to 212 microm were subjected to various extraction schemes. The smallest BeO particles are extracted more quickly than the largest particles, although at 90 degrees C even the largest BeO particles reach nearly quantitative extraction within 4 hr in 3% ABF. Extraction from mixed cellulosic-ester filters, cellulosic surface-sampling filters, wetted cellulosic dust wipes, and cotton gloves yielded 90% or greater recoveries. Scanning electron microscopy of BeO particles, including partially dissolved particles, shows that dissolution in dilute ABF occurs not just on the exterior surface but also via accessing particles' interiors due to porosity of the BeO material. Comparison of dissolution kinetics data shows that as particle diameter approximately doubles, extraction

  9. Friction stir welding of copper alloys

    Institute of Scientific and Technical Information of China (English)

    Liu Shuhua; Liu Meng; Wang Deqing; Xu Zhenyue

    2007-01-01

    Copper plates,brass plates and copper/brass plates were friction stir welded with various parameters. Experimental results show that the microstructure of the weld is characterized by its much finer grains as contrasted with the coarse grains of parent materials and the heat-affected zones are very narrow. The microhardness of the copper weld is a little higher than that of parent plate. The microhardness of brass weld is about 25% higher than that of parent material. The tensile strength of copper joints increases with increasing welding speed in the test range. The range of parameters to obtain good welds for copper is much wider than that for brass. When different materials were welded, the position of copper plate before welding affected the quality of FSW joints. If the copper plate was put on the advancing side of weld, the good quality of weld could be got under proper parameters.

  10. 钎焊真空度对铜与铪钎焊接头组织及性能的影响%Effects of Brazing Vacuum Degree on Microstructure and Mechanical Properties of Copper and Hafnium Brazed Joints

    Institute of Scientific and Technical Information of China (English)

    路希龙; 刘平; 刘新宽; 陈小红; 何代华; 李伟

    2014-01-01

    采用72Ag-28Cu钎料对铜与铪进行真空钎焊试验.钎焊温度为840℃,保温时间为15 min,真空度试验范围为5.0×10-2~8.0 Pa.研究了钎焊真空度对铜与铪钎焊接头组织及性能的影响,采用场发射扫描电子显微镜(FESEM)观察钎焊接头的组织形貌,采用ZWICK Z050电子万能材料试验机测试接头剪切强度.结果表明:随着钎焊真空度的升高,接头剪切强度呈先升高后降低的趋势;在钎焊温度为840℃、保温时间为15 min时,较佳的钎焊真空度为2.0×10-1 Pa.%Copper and hafnium was brazed with 72Ag-28Cu filler metal in vacuum on condition that the brazing temperature is 840℃ ,the holding time is 1 5 minutes and the vacuum degree is 5.0 × 10-2-8.0 Pa. The effects of brazing vacuum degree on microstructure and mechanical properties of the copper and hafnium brazing joints were studied based on the microstructure and morphology of the brazing joints observed by scanning electron microscope (FESEM)and the shear strength of the joints tested with electrical universal material testing machine ZWICK-Z050.The results show that,with the increase of the brazing vacuum degree,the shear strength of joints increased first and then decreased.When the brazing temperature is 840 ℃ and the holding time is 15 minutes,the best vacuum degree is 2.0×10-1 Pa.

  11. Primordial beryllium as a big bang calorimeter.

    Science.gov (United States)

    Pospelov, Maxim; Pradler, Josef

    2011-03-25

    Many models of new physics including variants of supersymmetry predict metastable long-lived particles that can decay during or after primordial nucleosynthesis, releasing significant amounts of nonthermal energy. The hadronic energy injection in these decays leads to the formation of ⁹Be via the chain of nonequilibrium transformations: Energy(h)→T, ³He→⁶He, ⁶Li→⁹Be. We calculate the efficiency of this transformation and show that if the injection happens at cosmic times of a few hours the release of O(10 MeV) per baryon can be sufficient for obtaining a sizable ⁹Be abundance. The absence of a plateau structure in the ⁹Be/H abundance down to a O(10⁻¹⁴) level allows one to use beryllium as a robust constraint on new physics models with decaying or annihilating particles.

  12. Investigation of the ion beryllium surface interaction

    Energy Technology Data Exchange (ETDEWEB)

    Guseva, M.I.; Birukov, A.Yu.; Gureev, V.M. [RRC Kurchatov Institute, Moscow (Russian Federation)] [and others

    1995-09-01

    The self -sputtering yield of the Be was measured. The energy dependence of the Be self-sputtering yield agrees well with that calculated by W. Eckstein et. al. Below 770 K the self-sputtering yield is temperature independent; at T{sub irr}.> 870 K it increases sharply. Hot-pressed samples at 370 K were implanted with monoenergetic 5 keV hydrogen ions and with a stationary plasma (flux power {approximately} 5 MW/m{sup 2}). The investigation of hydrogen behavior in beryllium shows that at low doses hydrogen is solved, but at doses {ge} 5x10{sup 22} m{sup -2} the bubbles and channels are formed. It results in hydrogen profile shift to the surface and decrease of its concentration. The sputtering results in further concentration decrease at doses > 10{sup 25}m{sup -2}.

  13. Effect of Reflow Time on Wetting Behavior, Microstructure Evolution, and Joint Strength of Sn-2.5Ag-0.5Cu Solder on Bare and Nickel-Coated Copper Substrates

    Science.gov (United States)

    Sona, Mrunali; Prabhu, K. Narayan

    2016-07-01

    The effect of reflow time on wetting behavior of Sn-2.5Ag-0.5Cu lead-free solder on bare and nickel-coated copper substrates has been investigated. The solder alloy was reflowed at 270°C for various reflow times of 10 s, 100 s, 300 s, and 500 s. On bare copper substrate, the intermetallic compound (IMC) thickness increased with increase in reflow time, whereas on Ni-coated Cu substrate, the IMC thickness increased up to 300 s followed by a drop for solder alloy reflowed for 500 s. The spreading behavior of the solder alloy was categorized into capillary, gravity (diffusion), and viscous zones. Gravity zone was obtained from 3.8 ± 0.43 s to 38.97 ± 3.38 s and from 5.99 ± 0.5 s to 77.82 ± 8.84 s for the Sn-2.5Ag-0.5Cu/Cu and Sn-2.5Ag-0.5Cu/Ni/Cu system, respectively. Sn-2.5Ag-0.5Cu solder alloy was also reflowed for the period corresponding to the end of the gravity zone (40 s and 80 s on bare and Ni-coated Cu, respectively). The joint strength was maximum at reflow time of 40 s and 80 s for the Sn-2.5Ag-0.5Cu/Cu and Sn-2.5Ag-0.5Cu/Ni/Cu system, respectively. The dynamic contact angle at the end of the gravity (diffusion) zone ( θ gz) was found to be a better parameter compared with the stabilized contact angle ( θ f) to assess the effect of the wettability of the liquid solder on the microstructure and joint strength. The present investigation reveals the significance of the gravity zone in assessment of optimum reflow time for lead-free solder alloys.

  14. New facility for post irradiation examination of neutron irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Ishitsuka, Etsuo; Kawamura, Hiroshi [Oarai Research Establishment, Ibaraki-Ken (Japan)

    1995-09-01

    Beryllium is expected as a neutron multiplier and plasma facing materials in the fusion reactor, and the neutron irradiation data on properties of beryllium up to 800{degrees}C need for the engineering design. The acquisition of data on the tritium behavior, swelling, thermal and mechanical properties are first priority in ITER design. Facility for the post irradiation examination of neutron irradiated beryllium was constructed in the hot laboratory of Japan Materials Testing Reactor to get the engineering design data mentioned above. This facility consist of the four glove boxes, dry air supplier, tritium monitoring and removal system, storage box of neutron irradiated samples. Beryllium handling are restricted by the amount of tritium;7.4 GBq/day and {sup 60}Co;7.4 MBq/day.

  15. The uses and adverse effects of beryllium on health

    DEFF Research Database (Denmark)

    Cooper, Ross G.; Harrison, Adrian Paul

    2009-01-01

    Context: This review describes the health effects of beryllium exposure in the workplace and the environment. Aim: To collate information on the consequences of occupational and environmental exposure to beryllium on physiological function and well being. Materials and Methods: The criteria used...... in the current review for selecting articles were adopted from proposed criteria in The International Classification of Functioning, Disability, and Health. Articles were classified based on acute and chronic exposure and toxicity of beryllium. Results: The proportions of utilized and nonutilized articles were...... published in sources unobtainable through requests at the British Library, and some had no impact factor and were excluded. Conclusion: Beryllium has some useful but undoubtedly harmful effects on health and well-being. Measures needed to be taken to prevent hazardous exposure to this element, making its...

  16. The beryllium production at Ulba metallurgical plant (Ust-Kamenogrsk, Kazakhstan)

    Energy Technology Data Exchange (ETDEWEB)

    Dvinskykh, E.M.; Savchuk, V.V.; Tuzov, Y.V. [Ulba Metallurgical Plant (Zavod), Ust-Kamenogorsk, Abay prospect 102 (Kazakhstan)

    1998-01-01

    The Report includes data on beryllium production of Ulba metallurgical plant, located in Ust-Kamenogorsk (Kazakhstan). Beryllium production is showed to have extended technological opportunities in manufacturing semi-products (beryllium ingots, master alloys, metallic beryllium powders, beryllium oxide) and in production of structural beryllium and its parts. Ulba metallurgical plant owns a unique technology of beryllium vacuum distillation, which allows to produce reactor grades of beryllium with a low content of metallic impurities. At present Ulba plant does not depend on raw materials suppliers. The quantity of stored raw materials and semi-products will allow to provide a 25-years work of beryllium production at a full capacity. The plant has a satisfactory experience in solving ecological problems, which could be useful in ITER program. (author)

  17. Development of Biomarkers for Chronic Beryllium Disease in Mice

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, Terry

    2013-01-25

    Beryllium is a strategic metal, indispensable for national defense programs in aerospace, telecommunications, electronics, and weaponry. Exposure to beryllium is an extensively documented occupational hazard that causes irreversible, debilitating granulomatous lung disease in as much as 3 - 5% of exposed workers. Mechanistic research on beryllium exposure-disease relationships has been severely limited by a general lack of a sufficient CBD animal model. We have now developed and tested an animal model which can be used for dissecting dose-response relationships and pathogenic mechanisms and for testing new diagnostic and treatment paradigms. We have created 3 strains of transgenic mice in which the human antigen-presenting moiety, HLA-DP, was inserted into the mouse genome. Each mouse strain contains HLA-DPB1 alleles that confer different magnitude of risk for chronic beryllium disease (CBD): HLA-DPB1*0401 (odds ratio = 0.2), HLA-DPB1*0201 (odds ratio = 15), HLA-DPB1*1701 (odds ratio = 240). Our preliminary work has demonstrated that the *1701 allele, as predicted by human studies, results in the greatest degree of sensitization in a mouse ear swelling test. We have also completed dose-response experiments examining beryllium-induced lung granulomas and identified susceptible and resistant inbred strains of mice (without the human transgenes) as well as quantitative trait loci that may contain gene(s) that modify the immune response to beryllium. In this grant application, we propose to use the transgenic and normal inbred strains of mice to identify biomarkers for the progression of beryllium sensitization and CBD. To achieve this goal, we propose to compare the sensitivity and accuracy of the lymphocyte proliferation test (blood and bronchoalveolar lavage fluid) with the ELISPOT test in the three HLA-DP transgenic mice strains throughout a 6 month treatment with beryllium particles. Because of the availability of high-throughput proteomics, we will also identify

  18. Recent results for bonding S-65C grade Be to copper alloys

    Energy Technology Data Exchange (ETDEWEB)

    Dombrowski, D.W. [Brush Wellman Inc., Cleveland, OH (United States)

    1995-09-01

    Novel processes for bonding beryllium to copper alloys without the use of a silver bonding aid have been developed at Brush Wellman. Tensile strength results will be presented at room temperature and elevated temperatures. A comparison will be made between bond strengths derived from rectangular tensile specimens and reduced section tensile specimens. Failure modes of the specimens at various temperatures will be shown.

  19. Actinide/beryllium neutron sources with reduced dispersion characteristics

    Science.gov (United States)

    Schulte, Louis D.

    2012-08-14

    Neutron source comprising a composite, said composite comprising crystals comprising BeO and AmBe.sub.13, and an excess of beryllium, wherein the crystals have an average size of less than 2 microns; the size distribution of the crystals is less than 2 microns; and the beryllium is present in a 7-fold to a 75-fold excess by weight of the amount of AmBe.sub.13; and methods of making thereof.

  20. Impurities effect on the swelling of neutron irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Donne, M.D.; Scaffidi-Argentina, F. [Institut fuer Neutronenphysik und Reaktortechnik, Karlsruhe (Germany)

    1995-09-01

    An important factor controlling the swelling behaviour of fast neutron irradiated beryllium is the impurity content which can strongly affect both the surface tension and the creep strength of this material. Being the volume swelling of the old beryllium (early sixties) systematically higher than that of the more modem one (end of the seventies), a sensitivity analysis with the aid of the computer code ANFIBE (ANalysis of Fusion Irradiated BEryllium) to investigate the effect of these material properties on the swelling behaviour of neutron irradiated beryllium has been performed. Two sets of experimental data have been selected: the first one named Western refers to quite recently produced Western beryllium, whilst the second one, named Russian refers to relatively old (early sixties) Russian beryllium containing a higher impurity rate than the Western one. The results obtained with the ANFIBE Code were assessed by comparison with experimental data and the used material properties were compared with the data available in the literature. Good agreement between calculated and measured values has been found.

  1. Copper hypersensitivity.

    Science.gov (United States)

    Fage, Simon W; Faurschou, Annesofie; Thyssen, Jacob P

    2014-10-01

    The world production of copper is steadily increasing. Although humans are widely exposed to copper-containing items on the skin and mucosa, allergic reactions to copper are only infrequently reported. To review the chemistry, biology and accessible data to clarify the implications of copper hypersensitivity, a database search of PubMed was performed with the following terms: copper, dermatitis, allergic contact dermatitis, contact hypersensitivity, contact sensitization, contact allergy, patch test, dental, IUD, epidemiology, clinical, and experimental. Human exposure to copper is relatively common. As a metal, it possesses many of the same qualities as nickel, which is a known strong sensitizer. Cumulative data on subjects with presumed related symptoms and/or suspected exposure showed that a weighted average of 3.8% had a positive patch test reaction to copper. We conclude that copper is a very weak sensitizer as compared with other metal compounds. However, in a few and selected cases, copper can result in clinically relevant allergic reactions.

  2. High heat flux testing of ITER ICH&CD antenna beryllium faraday screen bars mock-ups

    Energy Technology Data Exchange (ETDEWEB)

    Courtois, X., E-mail: xavier.courtois@cea.fr [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Meunier, L. [Fusion for Energy, 08019 Barcelona (Spain); Kuznetsov, V. [Efremov Institute, FSUE NIIEFA, St. Petersburg, 196641 (Russian Federation); Beaumont, B.; Lamalle, P. [ITER Organization, Route de Vinon sur Verdon, CS 90 046, 13067 St Paul Lez Durance (France); Conchon, D. [ATMOSTAT Co, F-94815 Villejuif (France); Languille, P. [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France)

    2016-11-01

    Highlights: • ITER ICH&CD antenna beryllium faraday screen bars mock-ups were manufactured. • The mock-ups are submitted to high heat loads to test their heat exhaust capabilities. • The mock-ups withstand without damage the design limit load. • Lifetime is gradually reduced when the heat load is augmented beyond the design limit. • Thermal and mechanical behavior are reproducible, and coherent with the calculation. - Abstract: The Faraday Screen (FS) is the plasma facing component of ITER ion cyclotron heating antennas shielding. The requirement for the high heat exhaust, and the limitation of the temperatures to minimize strain and thus offer sufficient resistance to fatigue, imply the need for high conductivity materials and a high cooling flow rate. The FS bars are constructed by a hipping process involving beryllium tiles, a pure copper layer, a copper chrome zirconium alloy for the cooling channel and a stainless steel backing strip. Two FS bars small scale mock-ups were manufactured and tested under high heat flux. They endured 15,000 heating cycles without degradation under nominal heat flux, and revealed growing flaws when the heat flux was progressively augmented beyond. In this case, the ultrasonic test confirms a strong delamination of the Be tiles.

  3. Copper transport.

    Science.gov (United States)

    Linder, M C; Wooten, L; Cerveza, P; Cotton, S; Shulze, R; Lomeli, N

    1998-05-01

    In adult humans, the net absorption of dietary copper is approximately 1 mg/d. Dietary copper joins some 4-5 mg of endogenous copper flowing into the gastrointestinal tract through various digestive juices. Most of this copper returns to the circulation and to the tissues (including liver) that formed them. Much lower amounts of copper flow into and out of other major parts of the body (including heart, skeletal muscle, and brain). Newly absorbed copper is transported to body tissues in two phases, borne primarily by plasma protein carriers (albumin, transcuprein, and ceruloplasmin). In the first phase, copper goes from the intestine to the liver and kidney; in the second phase, copper usually goes from the liver (and perhaps also the kidney) to other organs. Ceruloplasmin plays a role in this second phase. Alternatively, liver copper can also exit via the bile, and in a form that is less easily reabsorbed. Copper is also present in and transported by other body fluids, including those bathing the brain and central nervous system and surrounding the fetus in the amniotic sac. Ceruloplasmin is present in these fluids and may also be involved in copper transport there. The concentrations of copper and ceruloplasmin in milk vary with lactational stage. Parallel changes occur in ceruloplasmin messenger RNA expression in the mammary gland (as determined in pigs). Copper in milk ceruloplasmin appears to be particularly available for absorption, at least in rats.

  4. Active Metal Brazing and Characterization of Brazed Joints in C-C and C-SiC Composites to Copper-Clad-Molybdenum System

    Science.gov (United States)

    Singh, M.; Asthana, R.

    2008-01-01

    Carbon/carbon composites with CVI and resin-derived matrices, and C/SiC composites reinforced with T-300 carbon fibers in a CVI SiC matrix were joined to Cu-clad Mo using two Ag-Cu braze alloys, Cusil-ABA (1.75% Ti) and Ticusil (4.5% Ti). The brazed joints revealed good interfacial bonding, preferential precipitation of Ti at the composite/braze interface, and a tendency toward delamination in resin-derived C/C composite. Extensive braze penetration of the inter-fiber channels in the CVI C/C composites was observed. The Knoop microhardness (HK) distribution across the C/C joints indicated sharp gradients at the interface, and a higher hardness in Ticusil than in Cusil-ABA. For the C/SiC composite to Cu-clad-Mo joints, the effect of composite surface preparation revealed that ground samples did not crack whereas unground samples cracked. Calculated strain energy in brazed joints in both systems is comparable to the strain energy in a number of other ceramic/metal systems. Theoretical predictions of the effective thermal resistance suggest that such joined systems may be promising for thermal management applications.

  5. Copper hypersensitivity

    DEFF Research Database (Denmark)

    Fage, Simon W; Faurschou, Annesofie; Thyssen, Jacob P

    2014-01-01

    hypersensitivity, a database search of PubMed was performed with the following terms: copper, dermatitis, allergic contact dermatitis, contact hypersensitivity, contact sensitization, contact allergy, patch test, dental, IUD, epidemiology, clinical, and experimental. Human exposure to copper is relatively common...

  6. Proton irradiation effects on beryllium - A macroscopic assessment

    Science.gov (United States)

    Simos, Nikolaos; Elbakhshwan, Mohamed; Zhong, Zhong; Camino, Fernando

    2016-10-01

    Beryllium, due to its excellent neutron multiplication and moderation properties, in conjunction with its good thermal properties, is under consideration for use as plasma facing material in fusion reactors and as a very effective neutron reflector in fission reactors. While it is characterized by unique combination of structural, chemical, atomic number, and neutron absorption cross section it suffers, however, from irradiation generated transmutation gases such as helium and tritium which exhibit low solubility leading to supersaturation of the Be matrix and tend to precipitate into bubbles that coalesce and induce swelling and embrittlement thus degrading the metal and limiting its lifetime. Utilization of beryllium as a pion production low-Z target in high power proton accelerators has been sought both for its low Z and good thermal properties in an effort to mitigate thermos-mechanical shock that is expected to be induced under the multi-MW power demand. To assess irradiation-induced changes in the thermal and mechanical properties of Beryllium, a study focusing on proton irradiation damage effects has been undertaken using 200 MeV protons from the Brookhaven National Laboratory Linac and followed by a multi-faceted post-irradiation analysis that included the thermal and volumetric stability of irradiated beryllium, the stress-strain behavior and its ductility loss as a function of proton fluence and the effects of proton irradiation on the microstructure using synchrotron X-ray diffraction. The mimicking of high temperature irradiation of Beryllium via high temperature annealing schemes has been conducted as part of the post-irradiation study. This paper focuses on the thermal stability and mechanical property changes of the proton irradiated beryllium and presents results of the macroscopic property changes of Beryllium deduced from thermal and mechanical tests.

  7. Beryllium processing technology review for applications in plasma-facing components

    Energy Technology Data Exchange (ETDEWEB)

    Castro, R.G.; Jacobson, L.A.; Stanek, P.W.

    1993-07-01

    Materials research and development activities for the International Thermonuclear Experimental Reactor (ITER), i.e., the next generation fusion reactor, are investigating beryllium as the first-wall containment material for the reactor. Important in the selection of beryllium is the ability to process, fabricate and repair beryllium first-wall components using existing technologies. Two issues that will need to be addressed during the engineering design activity will be the bonding of beryllium tiles in high-heat-flux areas of the reactor, and the in situ repair of damaged beryllium tiles. The following review summarizes the current technology associated with welding and joining of beryllium to itself and other materials, and the state-of-the-art in plasma-spray technology as an in situ repair technique for damaged beryllium tiles. In addition, a review of the current status of beryllium technology in the former Soviet Union is also included.

  8. Validation of cleaning method for various parts fabricated at a Beryllium facility

    Energy Technology Data Exchange (ETDEWEB)

    Davis, Cynthia M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-12-15

    This study evaluated and documented a cleaning process that is used to clean parts that are fabricated at a beryllium facility at Los Alamos National Laboratory. The purpose of evaluating this cleaning process was to validate and approve it for future use to assure beryllium surface levels are below the Department of Energy’s release limits without the need to sample all parts leaving the facility. Inhaling or coming in contact with beryllium can cause an immune response that can result in an individual becoming sensitized to beryllium, which can then lead to a disease of the lungs called chronic beryllium disease, and possibly lung cancer. Thirty aluminum and thirty stainless steel parts were fabricated on a lathe in the beryllium facility, as well as thirty-two beryllium parts, for the purpose of testing a parts cleaning method that involved the use of ultrasonic cleaners. A cleaning method was created, documented, validated, and approved, to reduce beryllium contamination.

  9. The structure, properties and performance of plasma-sprayed beryllium for fusion applications

    Energy Technology Data Exchange (ETDEWEB)

    Castro, R.G.; Stanek, P.W.; Elliott, K.E. [and others

    1995-09-01

    Plasma-spray technology is under investigation as a method for producing high thermal conductivity beryllium coatings for use in magnetic fusion applications. Recent investigations have focused on optimizing the plasma-spray process for depositing beryllium coatings on damaged beryllium surfaces. Of particular interest has been optimizing the processing parameters to maximize the through-thickness thermal conductivity of the beryllium coatings. Experimental results will be reported on the use of secondary H{sub 2} gas additions to improve the melting of the beryllium powder and transferred-arc cleaning to improve the bonding between the beryllium coatings and the underlying surface. Information will also be presented on thermal fatigue tests which were done on beryllium coated ISX-B beryllium limiter tiles using 10 sec cycle times with 60 sec cooldowns and an International Thermonuclear Experimental Reactor (ITER) relevant divertor heat flux slightly in excess of 5 MW/m{sup 2}.

  10. Controlling Beryllium Contaminated Material And Equipment For The Building 9201-5 Legacy Material Disposition Project

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, T. D.; Easterling, S. D.

    2010-10-01

    This position paper addresses the management of beryllium contamination on legacy waste. The goal of the beryllium management program is to protect human health and the environment by preventing the release of beryllium through controlling surface contamination. Studies have shown by controlling beryllium surface contamination, potential airborne contamination is reduced or eliminated. Although there are areas in Building 9201-5 that are contaminated with radioactive materials and mercury, only beryllium contamination is addressed in this management plan. The overall goal of this initiative is the compliant packaging and disposal of beryllium waste from the 9201-5 Legacy Material Removal (LMR) Project to ensure that beryllium surface contamination and any potential airborne release of beryllium is controlled to levels as low as practicable in accordance with 10 CFR 850.25.

  11. Beryllium abundances in stars hosting giant planets

    CERN Document Server

    Santos, N C; Israelian, G; Mayor, M; Rebolo, R; García-Gíl, A; Pérez de Taoro, M R; Randich, S

    2002-01-01

    We have derived beryllium abundances in a wide sample of stars hosting planets, with spectral types in the range F7V-K0V, aimed at studying in detail the effects of the presence of planets on the structure and evolution of the associated stars. Predictions from current models are compared with the derived abundances and suggestions are provided to explain the observed inconsistencies. We show that while still not clear, the results suggest that theoretical models may have to be revised for stars with Teff<5500K. On the other hand, a comparison between planet host and non-planet host stars shows no clear difference between both populations. Although preliminary, this result favors a ``primordial'' origin for the metallicity ``excess'' observed for the planetary host stars. Under this assumption, i.e. that there would be no differences between stars with and without giant planets, the light element depletion pattern of our sample of stars may also be used to further investigate and constraint Li and Be deple...

  12. Steam-chemical reactivity for irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Anderl, R.A.; McCarthy, K.A.; Oates, M.A.; Petti, D.A.; Pawelko, R.J.; Smolik, G.R. [Idaho National Engineering and Environmental Lab., Idaho Falls, ID (United States)

    1998-01-01

    This paper reports the results of an experimental investigation to determine the influence of neutron irradiation effects and annealing on the chemical reactivity of beryllium exposed to steam. The work entailed measurements of the H{sub 2} generation rates for unirradiated and irradiated Be and for irradiated Be that had been previously annealed at different temperatures ranging from 450degC to 1200degC. H{sub 2} generation rates were similar for irradiated and unirradiated Be in steam-chemical reactivity experiments at temperatures between 450degC and 600degC. For irradiated Be exposed to steam at 700degC, the chemical reactivity accelerated rapidly and the specimen experienced a temperature excursion. Enhanced chemical reactivity at temperatures between 400degC and 600degC was observed for irradiated Be annealed at temperatures of 700degC and higher. This reactivity enhancement could be accounted for by the increased specific surface area resulting from development of a surface-connected porosity in the irradiated-annealed Be. (author)

  13. Report of a technical evaluation panel on the use of beryllium for ITER plasma facing material and blanket breeder material

    Energy Technology Data Exchange (ETDEWEB)

    Ulrickson, M.A. [ed.] [Sandia National Labs., Albuquerque, NM (United States); Manly, W.D. [Oak Ridge National Lab., TN (United States); Dombrowski, D.E. [Brush Wellman, Inc., Cleveland, OH (United States)] [and others

    1995-08-01

    Beryllium because of its low atomic number and high thermal conductivity, is a candidate for both ITER first wall and divertor surfaces. This study addresses the following: why beryllium; design requirements for the ITER divertor; beryllium supply and unirradiated physical/mechanical property database; effects of irradiation on beryllium properties; tritium issues; beryllium health and safety; beryllium-coolant interactions and safety; thermal and mechanical tests; plasma erosion of beryllium; recommended beryllium grades for ITER plasma facing components; proposed manufacturing methods to produce beryllium parts for ITER; emerging beryllium materials; proposed inspection and maintenance techniques for beryllium components and coatings; time table and costs; and the importance of integrating materials and manufacturing personnel with designers.

  14. Erosion of beryllium under ITER – Relevant transient plasma loads

    Energy Technology Data Exchange (ETDEWEB)

    Kupriyanov, I.B., E-mail: igkupr@gmail.com [A.A. Bochvar High Technology Research Institute of Inorganic Materials, Rogova St. 5a, 123060 Moscow (Russian Federation); Nikolaev, G.N.; Kurbatova, L.A.; Porezanov, N.P. [A.A. Bochvar High Technology Research Institute of Inorganic Materials, Rogova St. 5a, 123060 Moscow (Russian Federation); Podkovyrov, V.L.; Muzichenko, A.D.; Zhitlukhin, A.M. [TRINITI, Troitsk, Moscow reg. (Russian Federation); Gervash, A.A. [Efremov Research Institute, S-Peterburg (Russian Federation); Safronov, V.M. [Project Center of ITER, Moscow (Russian Federation)

    2015-08-15

    Highlights: • We study the erosion, mass loss/gain and surface structure evolution of Be/CuCrZr mock-ups, armored with beryllium of TGP-56FW grade after irradiation by deuterium plasma heat load of 0.5 MJ/m{sup 2} at 250 °C and 500 °C. • Beryllium mass loss/erosion under plasma heat load at 250 °C is rather small (no more than 0.2 g/m{sup 2} shot and 0.11 μm/shot, correspondingly, after 40 shots) and tends to decrease with increasing number of shots. • Beryllium mass loss/erosion under plasma heat load at 500 °C is much higher (∼2.3 g/m{sup 2} shot and 1.2 μm/shot, correspondingly, after 10 shot) and tends to decrease with increasing the number of shots (∼0.26 g/m{sup 2} pulse and 0.14 μm/shot, correspondingly, after 100 shot). • Beryllium erosion value derived from the measurements of profile of irradiated surface is much higher than erosion value derived from mass loss data. - Abstract: Beryllium will be used as a armor material for the ITER first wall. It is expected that erosion of beryllium under transient plasma loads such as the edge-localized modes (ELMs) and disruptions will mainly determine a lifetime of the ITER first wall. This paper presents the results of recent experiments with the Russian beryllium of TGP-56FW ITER grade on QSPA-Be plasma gun facility. The Be/CuCrZr mock-ups were exposed to up to 100 shots by deuterium plasma streams (5 cm in diameter) with pulse duration of 0.5 ms and heat loads range of 0.2–0.5 MJ/m{sup 2} at different temperature of beryllium tiles. The temperature of Be tiles has been maintained about 250 and 500 °C during the experiments. After 10, 40 and 100 shots, the beryllium mass loss/gain under erosion process were investigated as well as evolution of surface microstructure and cracks morphology.

  15. A Report on the Validation of Beryllium Strength Models

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, Derek Elswick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-02-05

    This report discusses work on validating beryllium strength models with flyer plate and Taylor rod experimental data. Strength models are calibrated with Hopkinson bar and quasi-static data. The Hopkinson bar data for beryllium provides strain rates up to about 4000 per second. A limitation of the Hopkinson bar data for beryllium is that it only provides information on strain up to about 0.15. The lack of high strain data at high strain rates makes it difficult to distinguish between various strength model settings. The PTW model has been calibrated many different times over the last 12 years. The lack of high strain data for high strain rates has resulted in these calibrated PTW models for beryllium exhibiting significantly different behavior when extrapolated to high strain. For beryllium, the α parameter of PTW has recently been calibrated to high precision shear modulus data. In the past the α value for beryllium was set based on expert judgment. The new α value for beryllium was used in a calibration of the beryllium PTW model by Sky Sjue. The calibration by Sjue used EOS table information to model the temperature dependence of the heat capacity. Also, the calibration by Sjue used EOS table information to model the density changes of the beryllium sample during the Hopkinson bar and quasi-static experiments. In this paper, the calibrated PTW model by Sjue is compared against experimental data and other strength models. The other strength models being considered are a PTW model calibrated by Shuh- Rong Chen and a Steinberg-Guinan type model by John Pedicini. The three strength models are used in a comparison against flyer plate and Taylor rod data. The results show that the Chen PTW model provides better agreement to this data. The Chen PTW model settings have been previously adjusted to provide a better fit to flyer plate data, whereas the Sjue PTW model has not been changed based on flyer plate data. However, the Sjue model provides a reasonable fit to

  16. Genetic determinants of sensitivity to beryllium in mice.

    Science.gov (United States)

    Tarantino-Hutchison, Lauren M; Sorrentino, Claudio; Nadas, Arthur; Zhu, Yiwen; Rubin, Edward M; Tinkle, Sally S; Weston, Ainsley; Gordon, Terry

    2009-06-01

    Chronic beryllium disease (CBD), an irreversible, debilitating granulomatous lung disease is caused by exposure to beryllium. This occupational hazard occurs in primary production and machining of Be-metal, BeO, beryllium - containing alloys, and other beryllium products. CBD begins as an MHC Class II-restricted, T(H)1 hypersensitivity, and the Human Leukocyte Antigen, HLA-DPB1E(69), is associated with risk of developing CBD. Because inbred strains of mice have not provided good models of CBD to date, three strains of HLA-DPB1 transgenic mice in an FVB/N background were developed; each contains a single allele of HLA-DPB1 that confers a different magnitude of risk for chronic beryllium disease: HLA-DPB1*0401 (OR approximately 0.2), HLA-DPB1*0201 (OR approximately 3), and HLA-DPB1*1701 (OR approximately 46). The mouse ear swelling test (MEST) was employed to determine if these different alleles would support a hypersensitivity response to beryllium. Mice were first sensitized on the back and subsequently challenged on the ear. In separate experiments, mice were placed into one of three groups (sensitization/challenge): C/C, C/Be, and Be/Be. In the HLA-DPB1*1701 mice, the strain with the highest risk transgene, the Be/Be group was the only group that displayed significant maximum increased ear thickness of 19.6% +/- 3.0% over the baseline measurement (p beryllium in seven inbred strains were investigated through use of the MEST, these included: FVB/N, AKR, Balb/c, C3H/HeJ, C57/BL6, DBA/2, and SJL/J. The FVB/N strain was least responsive, while the SJL/J and C57/BL6 strains were the highest responders. Our results suggest that the HLA-DPB1*1701 transgene product is an important risk factor for induction of the beryllium-sensitive phenotype. This model should be a useful tool for investigating beryllium sensitization.

  17. Experimental studies and modeling of processes of hydrogen isotopes interaction with beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Tazhibaeva, I.L.; Chikhray, Y.V.; Romanenko, O.G.; Klepikov, A.Kh.; Shestakov, V.P.; Kulsartov, T.V. [Science Research Inst. of Experimental and Theoretical Physics of Kazakh State Univ., Almaty (Kazakhstan); Kenzhin, E.A.

    1998-01-01

    The objective of this work was to clarify the surface beryllium oxide influence on hydrogen-beryllium interaction characteristics. Analysis of experimental data and modeling of processes of hydrogen isotopes accumulation, diffusion and release from neutron irradiated beryllium was used to achieve this purpose as well as the investigations of the changes of beryllium surface element composition being treated by H{sup +} and Ar{sup +} plasma glowing discharge. (author)

  18. Identification of beryllium-dependent peptides recognized by CD4+ T cells in chronic beryllium disease.

    Science.gov (United States)

    Falta, Michael T; Pinilla, Clemencia; Mack, Douglas G; Tinega, Alex N; Crawford, Frances; Giulianotti, Marc; Santos, Radleigh; Clayton, Gina M; Wang, Yuxiao; Zhang, Xuewu; Maier, Lisa A; Marrack, Philippa; Kappler, John W; Fontenot, Andrew P

    2013-07-01

    Chronic beryllium disease (CBD) is a granulomatous disorder characterized by an influx of beryllium (Be)-specific CD4⁺ T cells into the lung. The vast majority of these T cells recognize Be in an HLA-DP–restricted manner, and peptide is required for T cell recognition. However, the peptides that stimulate Be-specific T cells are unknown. Using positional scanning libraries and fibroblasts expressing HLA-DP2, the most prevalent HLA-DP molecule linked to disease, we identified mimotopes and endogenous self-peptides that bind to MHCII and Be, forming a complex recognized by pathogenic CD4⁺ T cells in CBD. These peptides possess aspartic and glutamic acid residues at p4 and p7, respectively, that surround the putative Be-binding site and cooperate with HLA-DP2 in Be coordination. Endogenous plexin A peptides and proteins, which share the core motif and are expressed in lung, also stimulate these TCRs. Be-loaded HLA-DP2–mimotope and HLA-DP2–plexin A4 tetramers detected high frequencies of CD4⁺ T cells specific for these ligands in all HLADP2+ CBD patients tested. Thus, our findings identify the first ligand for a CD4⁺ T cell involved in metal-induced hypersensitivity and suggest a unique role of these peptides in metal ion coordination and the generation of a common antigen specificity in CBD.

  19. Behavior of carboxylic acids upon complexation with beryllium compounds.

    Science.gov (United States)

    Mykolayivna-Lemishko, Kateryna; Montero-Campillo, M Merced; Mó, Otilia; Yáñez, Manuel

    2014-07-31

    A significant acidity enhancement and changes on aromaticity were previously observed in squaric acid and its derivatives when beryllium bonds are present in those systems. In order to know if these changes on the chemical properties could be considered a general behavior of carboxylic acids upon complexation with beryllium compounds, complexes between a set of representative carboxylic acids RCOOH (formic acid, acetic acid, propanoic acid, benzoic acid, and oxalic acid) and beryllium compounds BeX2 (X = H, F, Cl) were studied by means of density functional theory calculations. Complexes that contain a dihydrogen bond or a OH···X interaction are the most stable in comparison with other possible BeX2 complexation patterns in which no other weak interactions are involved apart from the beryllium bond. Formic, acetic, propanoic, benzoic, and oxalic acid complexes with BeX2 are much stronger acids than their related free forms. The analysis of the topology of the electron density helps to clarify the reasons behind this acidity enhancement. Importantly, when the halogen atom is replaced by hydrogen in the beryllium compound, the dihydrogen bond complex spontaneously generates a new neutral complex [RCOO:BeH] in which a hydrogen molecule is lost. This seems to be a trend for carboxylic acids on complexing BeX2 compounds.

  20. Design and cooling of BESIII beryllium beam pipe

    Science.gov (United States)

    Li, Xunfeng; Ji, Quan; Wang, Li; Zheng, Lifang

    2008-01-01

    The beryllium beam pipe was restructured according to the requirements of the upgraded BESIII (Beijing Spectrometer) experiment. SMO-1 (sparking machining oil no. 1) was selected as the coolant for the central beryllium beam pipe. The cooling gap width of the beryllium beam pipe was calculated, the influence of concentrated heat load on the wall temperature of the beryllium beam pipe was studied, and the optimal velocity of the SMO-1 in the gap was determined at the maximum heat load. A cooling system for the beam pipe was developed to control the outer wall temperature of the beam pipe. The cooling system is reported in this paper with regard to the following two aspects: the layouts and the automation. The performance of the cooling system was tested on the beam pipe model with trim size. The test results show that the design of the beryllium beam pipe is reasonable and that the cooling system achieves the BESIII experimental aim. The cooling system has already passed the acceptance test and has been installed in position. It will be put into practice for the BESIII experiment in 2008.

  1. 10000 Tonnes Of Copper Concentrate Arrived At Nanjing Port

    Institute of Scientific and Technical Information of China (English)

    2016-01-01

    On March 20,a cargo ship loaded with 10000tonnes of copper concentrate docked at Nanjing Port,signaling that the biggest overseas acquisition project of China’s metal industry received concrete result.On that day,the first batch shipment of 11330tonnes of copper concentrate from Peru Las Bambas Copper Mine,a project jointly

  2. Optimization of mechanically jointed doped graphite/copper plasma facing components%核聚变掺杂石墨第一壁材料连接优化分析

    Institute of Scientific and Technical Information of China (English)

    种法力

    2012-01-01

    Two kinds of mechanically jointed graphite/copper structures were introduced, and their heat transfer performances were evaluated by means of electron beam facility and ANSYS finite element analysis. The results show that the temperature differences of two joints are not significant, and the maximum surface temperature is about 1 05S ℃ at 4 MW/m2, which has a good agreement with the numerical simulation results by ANSYS. Due to its poor heal transfer, the screw-fastened region appears the higher temperature, especially for Joint_l, it reachs about 2 000 ℃. It's indicated that Joint_2 could be more suitable to the heat flux region of less than 4 MW/nr. But under the higher heat flux, both of them are un-acceptable, an advanced plasma facing component has to be developed.%介绍核聚变实验装置掺杂石墨第一壁材料的两种机械连接方法,通过电子束热负荷实验及ANSYS有限元分析评价两种连接方式传热效果的差异.结果表明,两种连接方式传热效果相当,在4MW/m2功率密度下表面最高温度约为1055℃.ANSYS分析结果与实验结果有较高的一致性,但是由于螺钉固定区域散热较差,此处温度最高达到2000℃.对于功率密度低于4MW/m2的区域,掺杂石墨第一壁材料采用第二种方式连接较为合适;对于较高热负荷功率密度沉积的区域或者聚变实验装置,发展先进第一壁材料及连接方法十分必要.

  3. 10 CFR Appendix A to Part 850 - Chronic Beryllium Disease Prevention Program Informed Consent Form

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Chronic Beryllium Disease Prevention Program Informed Consent Form A Appendix A to Part 850 Energy DEPARTMENT OF ENERGY CHRONIC BERYLLIUM DISEASE PREVENTION PROGRAM Pt. 850, App. A Appendix A to Part 850—Chronic Beryllium Disease Prevention Program...

  4. Risk-based approach for controlling beryllium exposure in a manufacturing environment

    Energy Technology Data Exchange (ETDEWEB)

    Gilmore, W. E. (Walter E.); Clawson, C. D. (Chris D.); Ellis, K. K. (Kimberly K.)

    2003-01-01

    There are many diverse uses for beryllium in both military and industrial applications. Unfortunately, there are certain worker health risks associated with the manufacture and production of beryllium products. Respiratory illnesses due to prolonged contact with beryllium particulate are of paramount concern. However, these health risks can be controlled provided that the appropriate protective measures to prevent worker exposure from beryllium are in place. But it is no1 always a straightforward process to identify exactly what the beryllium protective measures should be in order to realize a true risk savings. Without prudent attention to a systematic inquiry and suitable evaluative criteria, a program for controlling beryllium health risks can be lacking in completeness and overall effectiveness. One approach that took into account the necessary ingredients for risk-based determination of beryllium protective measures was developed for a beryllium operation at a Department of Energy (DOE) facility. The methodological framework that was applied at this facility, as well as a discussion of the final beryllium protective measures that were determined by this approach will be presented. Regulatory aspects for working with beryllium, as well as a risk-assessment strategy for ranking beryllium-handling activities with respect to exposure potential will also be discussed. The presentation will conclude with a synopsis of lessons-learned as gleaned from this case study, as well as providing the participants with a constructive blueprint that can be adapted to other processes involving beryllium.

  5. 10 CFR 71.23 - General license: Plutonium-beryllium special form material.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false General license: Plutonium-beryllium special form material... RADIOACTIVE MATERIAL General Licenses § 71.23 General license: Plutonium-beryllium special form material. (a... form of plutonium-beryllium (Pu-Be) special form sealed sources, or to deliver Pu-Be sealed sources...

  6. Monte Carlo uncertainty analyses for integral beryllium experiments

    CERN Document Server

    Fischer, U; Tsige-Tamirat, H

    2000-01-01

    The novel Monte Carlo technique for calculating point detector sensitivities has been applied to two representative beryllium transmission experiments with the objective to investigate the sensitivity of important responses such as the neutron multiplication and to assess the related uncertainties due to the underlying cross-section data uncertainties. As an important result, it has been revealed that the neutron multiplication power of beryllium can be predicted with good accuracy using state-of-the-art nuclear data evaluations. Severe discrepancies do exist for the spectral neutron flux distribution that would transmit into significant uncertainties of the calculated neutron spectra and of the nuclear blanket performance in blanket design calculations. With regard to this, it is suggested to re-analyse the secondary energy and angle distribution data of beryllium by means of Monte Carlo based sensitivity and uncertainty calculations. Related code development work is underway.

  7. Estimation of beryllium ground state energy by Monte Carlo simulation

    Energy Technology Data Exchange (ETDEWEB)

    Kabir, K. M. Ariful [Department of Physical Sciences, School of Engineering and Computer Science, Independent University, Bangladesh (IUB) Dhaka (Bangladesh); Halder, Amal [Department of Mathematics, University of Dhaka Dhaka (Bangladesh)

    2015-05-15

    Quantum Monte Carlo method represent a powerful and broadly applicable computational tool for finding very accurate solution of the stationary Schrödinger equation for atoms, molecules, solids and a variety of model systems. Using variational Monte Carlo method we have calculated the ground state energy of the Beryllium atom. Our calculation are based on using a modified four parameters trial wave function which leads to good result comparing with the few parameters trial wave functions presented before. Based on random Numbers we can generate a large sample of electron locations to estimate the ground state energy of Beryllium. Our calculation gives good estimation for the ground state energy of the Beryllium atom comparing with the corresponding exact data.

  8. Field-emission spectroscopy of beryllium atoms adsorbed on tungsten

    Energy Technology Data Exchange (ETDEWEB)

    Czyzewski, J.J.; Grzesiak, W.; Krajniak, J. (Politechnika Wroclawska (Poland))

    1981-01-01

    Field emission energy distributions (FEED) have been measured for the beryllium-tungsten (023) adsorption system over the 78-450 K temperature range. A temperature dependence of the normalized half-width, ..delta../d, of FEED peaks changed significantly due to beryllium adsorption; and the curve, ..delta../d vs p, for the Be/W adsorption system was identical in character to the calculated curve based on the free electron model in contrast to the curve for the clean tungsten surface. In the last part of this paper Gadzuk's theory of the resonance-tunneling effect is applied to the beryllium atom on tungsten. Experimental and theoretical curves of the enhancement factor as a function of energy have been discussed.

  9. Color Enhancement by Diffusion of Beryllium in Dark Blue Sapphire

    Institute of Scientific and Technical Information of China (English)

    Kyungj in Kim; Yongkil Ahn

    2016-01-01

    Diffusion of beryllium was performed on dark blue sapphire from China and Australia.The samples were heated with beryllium as a dopant in a furnace at 1 600 ℃ for 42 h in air.After beryllium diffusion,sam-ples were analyzed by UV-Vis,FTIR,and WD-XRF spectroscopy.After heat-treatment with Be as a catalyst, the irons of the ferrous state were changed to the ferric state.Therefore,reaction of Fe2+/Ti4+ IVCT was de-creased.The absorption peaks at 3 309 cm-1 attributed to OH radical were disappeared completely due to carry out heat treatment.Consequently,the intensity of absorption band was decreased in the visible region.Espe-cially,decreased absorption band in the vicinity of 570 nm was responsible for the lighter blue color.There-fore,we confirmed that the dark blue sapphires from China and Australia were changed to vivid blue.

  10. Explosive compact-coating of tungsten–copper alloy to a copper surface

    Science.gov (United States)

    Chen, Xiang; Li, Xiaojie; Yan, Honghao; Wang, Xiaohong; Miao, Yusong

    2017-03-01

    This study proposed a new method for coating tungsten–copper alloy to copper surface. First, the tungsten–copper alloy powder was pre-compacted to the copper surface. Then, the powder in the hydrogen atmosphere was sintered, and the pre-compacted powder was compacted by explosive compact-coating. Finally, diffusion sintering was conducted to improve the density of the coating layer. The theoretical density of the coating reached 99.3%. Microstructure characteristics indicated that tungsten and copper powders were well mixed. Tungsten particles were larger than copper particles. Scanning electron microscope (SEM) fracture surface analysis was different from the traditional fracture of metals. Coating and substrate joint surfaces, which were analyzed by SEM, indicated that the tungsten–copper alloy was sintered on the copper surface. The hardness of the coating layer was 197.6–245.2 HV, and the hardness of the substrate was approximately 55 HV.

  11. Process Of Bonding Copper And Tungsten

    Science.gov (United States)

    Slattery, Kevin T.; Driemeyer, Daniel E.

    1999-11-23

    Process for bonding a copper substrate to a tungsten substrate by providing a thin metallic adhesion promoting film bonded to a tungsten substrate and a functionally graded material (FGM) interlayer bonding the thin metallic adhesion promoting film to the copper substrate. The FGM interlayer is formed by thermal plasma spraying mixtures of copper powder and tungsten powder in a varied blending ratio such that the blending ratio of the copper powder and the tungsten powder that is fed to a plasma torch is intermittently adjusted to provide progressively higher copper content/tungsten content, by volume, ratio values in the interlayer in a lineal direction extending from the tungsten substrate towards the copper substrate. The resulting copper to tungsten joint well accommodates the difference in the coefficient of thermal expansion of the materials.

  12. Neutron irradiation behavior of ITER candidate beryllium grades

    Energy Technology Data Exchange (ETDEWEB)

    Kupriyanov, I.B.; Gorokhov, V.A.; Nikolaev, G.N. [A.A.Bochvar All-Russia Scientific Research Inst. of Inorganic Materials (VNIINM), Moscow (Russian Federation); Melder, R.R.; Ostrovsky, Z.E.

    1998-01-01

    Beryllium is one of the main candidate materials both for the neutron multiplier in a solid breeding blanket and for the plasma facing components. That is why its behaviour under the typical for fusion reactor loading, in particular, under the neutron irradiation is of a great importance. This paper presents mechanical properties, swelling and microstructure of six beryllium grades (DshG-200, TR-30, TshG-56, TRR, TE-30, TIP-30) fabricated by VNIINM, Russia and also one - (S-65) fabricated by Brush Wellman, USA. The average grain size of the beryllium grades varied from 8 to 25 {mu}m, beryllium oxide content was 0.8-3.2 wt. %, initial tensile strength was 250-680 MPa. All the samples were irradiated in active zone of SM-3 reactor up to the fast neutron fluence (5.5-6.2) {center_dot} 10{sup 21} cm{sup -2} (2.7-3.0 dpa, helium content up to 1150 appm), E > 0.1 MeV at two temperature ranges: T{sub 1} = 130-180degC and T{sub 2} = 650-700degC. After irradiation at 130-180degC no changes in samples dimensions were revealed. After irradiation at 650-700degC swelling of the materials was found to be in the range 0.1-2.1 %. Beryllium grades TR-30 and TRR, having the smallest grain size and highest beryllium oxide content, demonstrated minimal swelling, which was no more than 0.1 % at 650-700degC and fluence 5.5 {center_dot} 10{sup 21} cm{sup -2}. Tensile and compression test results and microstructure parameters measured before and after irradiation are also presented. (author)

  13. Method for removal of beryllium contamination from an article

    Science.gov (United States)

    Simandl, Ronald F.; Hollenbeck, Scott M.

    2012-12-25

    A method of removal of beryllium contamination from an article is disclosed. The method typically involves dissolving polyisobutylene in a solvent such as hexane to form a tackifier solution, soaking the substrate in the tackifier to produce a preform, and then drying the preform to produce the cleaning medium. The cleaning media are typically used dry, without any liquid cleaning agent to rub the surface of the article and remove the beryllium contamination below a non-detect level. In some embodiments no detectible residue is transferred from the cleaning wipe to the article as a result of the cleaning process.

  14. Relativistic and QED corrections for the beryllium atom.

    Science.gov (United States)

    Pachucki, Krzysztof; Komasa, Jacek

    2004-05-28

    Complete relativistic and quantum electrodynamics corrections of order alpha(2) Ry and alpha(3) Ry are calculated for the ground state of the beryllium atom and its positive ion. A basis set of correlated Gaussian functions is used, with exponents optimized against nonrelativistic binding energies. The results for Bethe logarithms ln(k(0)(Be)=5.750 34(3) and ln(k(0)(Be+)=5.751 67(3) demonstrate the availability of high precision theoretical predictions for energy levels of the beryllium atom and light ions. Our recommended value of the ionization potential 75 192.514(80) cm(-1) agrees with equally accurate available experimental values.

  15. CHAPTER 7. BERYLLIUM ANALYSIS BY NON-PLASMA BASED METHODS

    Energy Technology Data Exchange (ETDEWEB)

    Ekechukwu, A

    2009-04-20

    The most common method of analysis for beryllium is inductively coupled plasma atomic emission spectrometry (ICP-AES). This method, along with inductively coupled plasma mass spectrometry (ICP-MS), is discussed in Chapter 6. However, other methods exist and have been used for different applications. These methods include spectroscopic, chromatographic, colorimetric, and electrochemical. This chapter provides an overview of beryllium analysis methods other than plasma spectrometry (inductively coupled plasma atomic emission spectrometry or mass spectrometry). The basic methods, detection limits and interferences are described. Specific applications from the literature are also presented.

  16. 20 CFR 30.207 - How does a claimant prove a diagnosis of a beryllium disease covered under Part B?

    Science.gov (United States)

    2010-04-01

    ... beryllium disease covered under Part B? 30.207 Section 30.207 Employees' Benefits OFFICE OF WORKERS... Beryllium Illness Under Part B of Eeoicpa § 30.207 How does a claimant prove a diagnosis of a beryllium... employee developed a covered beryllium illness. Proof that the employee developed a covered...

  17. Corrosion of dental copper, nickel, and gold alloys in artificial saliva and saline solutions.

    Science.gov (United States)

    Johansson, B I; Lemons, J E; Hao, S Q

    1989-09-01

    The purpose of this investigation was to study the tarnish and corrosion of three commercial copper alloys, three experimental copper alloys, two nickel alloys, and one high-gold alloy by exposing the specimens for four weeks to artificial saliva and saline solutions. Half of the specimens were brushed, and the solutions were changed regularly. The copper-based and the beryllium-containing nickel alloys exhibited significant surface alterations after exposure to either solution. The potential of elevated release of ions to the oral cavity and to the target organs by some of the investigated alloys should be considered if dental usage of these alloys is to be extended.

  18. Extraction of beryllium sulfate by a long chain amine; Extraction du sulfate de beryllium par une amine a longue chaine

    Energy Technology Data Exchange (ETDEWEB)

    Etaix, E.S. [Commissariat a l' Energie Atomique, Fontenay-Aux-Roses (France). Centre d' Etudes Nucleaires

    1968-06-01

    The extraction of sulfuric acid in aqueous solution by a primary amine in benzene solution, 3-9 (diethyl) - 6-amino tri-decane (D.E.T. ) - i.e., with American nomenclature 1-3 (ethyl-pentyl) - 4-ethyl-octyl amine (E.P.O.) - has made it possible to calculate the formation constants of alkyl-ammonium sulfate and acid sulfate. The formula of the beryllium and alkyl-ammonium sulfate complex formed in benzene has next been determined, for various initial acidity of the aqueous solution. Lastly, evidence has been given of negatively charged complexes of beryllium and sulfate in aqueous solution, through the dependence of the aqueous sulfate ions concentration upon beryllium extraction. The formation constant of these anionic complexes has been evaluated. (author) [French] L'etude de l'extraction de l'acide sulfurique en solution aqueuse par une amine primaire en solution dans le benzene, le diethyl-3,9 amino-6 tridecane (D.E.T.) - autre nom americain 1-3 (ethylpentyl) - 4-ethyloctylamine (E.P.O.) a permis de calculer les constantes de formation du sulfate et de l'hydrogenosulfate d'alkyl-ammonium. La formule du complexe de sulfate de beryllium et d'alkyl-ammonium forme en solution benzenique a ete ensuite determinee pour diverses acidites initiales de la solution aqueuse. Enfin, l'influence de la concentration des ions sulfate de la phase aqueuse sur l'extraction du beryllium a mis en evidence la formation en solution aqueuse de complexes anioniques de sulfate et de beryllium dont la constante de formation a ete evaluee. (auteur)

  19. Beryllium solubility in occupational airborne particles: Sequential extraction procedure and workplace application.

    Science.gov (United States)

    Rousset, Davy; Durand, Thibaut

    2016-01-01

    Modification of an existing sequential extraction procedure for inorganic beryllium species in the particulate matter of emissions and in working areas is described. The speciation protocol was adapted to carry out beryllium extraction in closed-face cassette sampler to take wall deposits into account. This four-step sequential extraction procedure aims to separate beryllium salts, metal, and oxides from airborne particles for individual quantification. Characterization of the beryllium species according to their solubility in air samples may provide information relative to toxicity, which is potentially related to the different beryllium chemical forms. Beryllium salts (BeF(2), BeSO(4)), metallic beryllium (Bemet), and beryllium oxide (BeO) were first individually tested, and then tested in mixtures. Cassettes were spiked with these species and recovery rates were calculated. Quantitative analyses with matched matrix were performed using inductively coupled plasma mass spectrometry (ICP-MS). Method Detection Limits (MDLs) were calculated for the four matrices used in the different extraction steps. In all cases, the MDL was below 4.2 ng/sample. This method is appropriate for assessing occupational exposure to beryllium as the lowest recommended threshold limit values are 0.01 µg.m(-3) in France([) (1) (]) and 0.05 µg.m(-3) in the USA.([ 2 ]) The protocol was then tested on samples from French factories where occupational beryllium exposure was suspected. Beryllium solubility was variable between factories and among the same workplace between different tasks.

  20. China Metallurgical Group and Jiangxi Copper Having Signed Agreement on Copper Mines with Afghanistan

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>On May 25,the joint investment combo formed by China Metallurgical Group Corp.(MCC) and Jiangxi Copper Co.has formally signed agreement with Afghan government in Kabul on the exploitation of Aynak copper mine.The mine is situated in the north of Loghar in the middle east of Afghanistan,which is about 35km from the Capital City of Kabul.The ex- tra-large copper mine was found at the begin-

  1. On-line separation of short-lived beryllium isotopes

    CERN Document Server

    Köster, U; Catherall, R; Fedosseev, V; Georg, U; Huber, G; Jading, Y; Jonsson, O; Koizumi, M; Kratz, K L; Kugler, E; Lettry, Jacques; Mishin, V I; Ravn, H L; Sebastian, V; Tamburella, C; Wöhr, A

    1998-01-01

    With the development of a new laser ionization scheme, it became possible to ionize beryllium efficiently in the hot cavity of the ISOLDE laser ion source. The high target and ion source temperatures enable the release of short-lived beryllium isotopes. Thus all particle-stable beryllium isotopes could be extracted from a standard uranium carbide/graphite target. For the first time the short-lived isotopes /sup 12/Be and /sup 14/Be could be identified at an ISOL facility, /sup 14/Be being among the most short-lived isotopes separated so far at ISOLDE. The release time from the UC/graphite target was studied with several beryllium isotopes. Profiting from the element selectivity of laser ionization, the strong and isotopically pure beam of /sup 12/Be allowed to determine the half- life to T/sub 1/2 /=21.34(23) ms and the probability of beta-delayed neutron emission to P/sub n/=0.48/sub -0.10//sup +0.12/(23 refs).

  2. Codeposition of deuterium ions with beryllium oxide at elevated temperatures

    CERN Document Server

    Markin, A V; Gorodetsky, A E; Negodaev, M A; Rozhanskii, N V; Scaffidi-Argentina, F; Werle, H; Wu, C H; Zalavutdinov, R K; Zakharov, A P

    2000-01-01

    Deuterium-loaded BeO films were produced by sputtering the beryllium target with 10 keV Ne ions in D sub 2 gas at a pressure of approximately 1 Pa. The sputtered beryllium reacts - on the substrate surface - with the residual oxygen, thus forming a beryllium oxide layer. Biasing the substrate negatively with respect to the target provides the simultaneous bombardment of the growing film surface with D ions formed by Ne-D sub 2 collisions. Substrate potential governs the maximum energy of ions striking the growing film surface while its size governs the flux density. According to X-ray photoelectron spectroscopy (XPS), electron probe microanalysis (EPMA) and reflection high energy electron diffraction (RHEED) data, the beryllium is deposited in the form of polycrystalline hcp-BeO layers with negligible (about 1 at.%) carbon and neon retention. Thermal desorption spectroscopy (TDS) data shows a strong deuterium bonding, with a desorption peak at 950 K, in the films deposited at -50 and -400 V substrate potentia...

  3. THORIUM-BERYLLIUM ALLOYS AND METHOD OF PRODUCING SAME

    Science.gov (United States)

    Spedding, F.H.; Wilhelm, H.A.; Keller, W.H.

    1959-09-01

    >The preparation is described of thorium-berylium alloys from halides of the metals by stmultaneously reducing thorium fluoride and beryllium fluoride with calcium at approximately 650 deg C and maintaining the temperature until the thorium-beryhltum alloy separates from the slag.

  4. TEM study of impurity segregations in beryllium pebbles

    Science.gov (United States)

    Klimenkov, M.; Chakin, V.; Moeslang, A.; Rolli, R.

    2014-12-01

    Beryllium is planned to be used as a neutron multiplier in the Helium-cooled Pebble Bed European concept of a breeding blanket of demonstration power reactor DEMO. In order to evaluate the irradiation performance, individual pebbles and constrained pebble beds were neutron-irradiated at temperatures typical of fusion blankets. Beryllium pebbles 1 mm in diameter produced by the rotating electrode method were subjected to a TEM study before and after irradiation at High Flux Reactor, Petten, Netherlands at 861 K. The grain size varied in a wide range from sub-micron size up to several tens of micrometers, which indicated formation bimodal grain size distribution. Based on the application of combined electron energy loss spectroscopy and energy dispersive X-ray spectroscopy methods, we suggest that impurity precipitates play an important role in controlling the mechanical properties of beryllium. The impurity elements were present in beryllium at a sub-percent concentration form beryllide particles of a complex (Fe/Al/Mn/Cr)B composition. These particles are often ordered along dislocations lines, forming several micron-long chains. It can be suggested that fracture surfaces often extended along these chains in irradiated material.

  5. TEM study of impurity segregations in beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Klimenkov, M., E-mail: michael.klimenkov@kit.edu [Institute for Applied Materials – Applied Materials Physics, Karlsruhe Institute of Technology, Hermann-von-Helmholz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Chakin, V.; Moeslang, A. [Institute for Applied Materials – Applied Materials Physics, Karlsruhe Institute of Technology, Hermann-von-Helmholz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Rolli, R. [Institute for Applied Materials – Materials and Biomechanics, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany)

    2014-12-15

    Beryllium is planned to be used as a neutron multiplier in the Helium-cooled Pebble Bed European concept of a breeding blanket of demonstration power reactor DEMO. In order to evaluate the irradiation performance, individual pebbles and constrained pebble beds were neutron-irradiated at temperatures typical of fusion blankets. Beryllium pebbles 1 mm in diameter produced by the rotating electrode method were subjected to a TEM study before and after irradiation at High Flux Reactor, Petten, Netherlands at 861 K. The grain size varied in a wide range from sub-micron size up to several tens of micrometers, which indicated formation bimodal grain size distribution. Based on the application of combined electron energy loss spectroscopy and energy dispersive X-ray spectroscopy methods, we suggest that impurity precipitates play an important role in controlling the mechanical properties of beryllium. The impurity elements were present in beryllium at a sub-percent concentration form beryllide particles of a complex (Fe/Al/Mn/Cr)B composition. These particles are often ordered along dislocations lines, forming several micron-long chains. It can be suggested that fracture surfaces often extended along these chains in irradiated material.

  6. 75 FR 80734 - Chronic Beryllium Disease Prevention Program

    Science.gov (United States)

    2010-12-23

    ... a person's immune system becomes highly responsive (allergic) to the presence of beryllium in the.... Hardcopies (2 copies) sent by regular mailing should be addressed to: Jacqueline D. Rogers, Office of Worker... to jackie.rogers@hq.doe.gov . If you have additional information, such as studies or journal articles...

  7. The uses and adverse effects of beryllium on health

    Directory of Open Access Journals (Sweden)

    Cooper Ross

    2009-01-01

    Full Text Available Context: This review describes the health effects of beryllium exposure in the workplace and the environment. Aim: To collate information on the consequences of occupational and environmental exposure to beryllium on physiological function and well being. Materials and Methods: The criteria used in the current review for selecting articles were adopted from proposed criteria in The International Classification of Functioning, Disability, and Health. Articles were classified based on acute and chronic exposure and toxicity of beryllium. Results: The proportions of utilized and nonutilized articles were tabulated. Years 2001-10 gave the greatest match (45.9% for methodological parameters, followed by 27.71% for 1991-2000. Years 1971-80 and 1981-90 were not significantly different in the information published and available whereas years 1951-1960 showed a lack of suitable articles. Some articles were published in sources unobtainable through requests at the British Library, and some had no impact factor and were excluded. Conclusion: Beryllium has some useful but undoubtedly harmful effects on health and well-being. Measures need to be taken to prevent hazardous exposure to this element, making its biological monitoring in the workplace essential.

  8. Biological exposure metrics of beryllium-exposed dental technicians.

    Science.gov (United States)

    Stark, Moshe; Lerman, Yehuda; Kapel, Arik; Pardo, Asher; Schwarz, Yehuda; Newman, Lee; Maier, Lisa; Fireman, Elizabeth

    2014-01-01

    Beryllium is commonly used in the dental industry. This study investigates the association between particle size and shape in induced sputum (IS) with beryllium exposure and oxidative stress in 83 dental technicians. Particle size and shape were defined by laser and video, whereas beryllium exposure data came from self-reports and beryllium lymphocyte proliferation test (BeLPT) results. Heme oxygenase-1 (HO1) gene expression in IS was evaluated by quantitative polymerase chain reaction. A high content of particles (92%) in IS >5 μ in size is correlated to a positive BeLPT risk (odds ratio [OR] = 3.4, 95% confidence interval [CI]: 0.9-13). Use of masks, hoods, and type of exposure yielded differences in the transparency of IS particles (gray level) and modulate HO1 levels. These results indicate that parameters of size and shape of particles in IS are sensitive to workplace hygiene, affect the level of oxidative stress, and may be potential markers for monitoring hazardous dust exposures.

  9. Determination of beryllium concentrations in UK ambient air

    Science.gov (United States)

    Goddard, Sharon L.; Brown, Richard J. C.; Ghatora, Baljit K.

    2016-12-01

    Air quality monitoring of ambient air is essential to minimise the exposure of the general population to toxic substances such as heavy metals, and thus the health risks associated with them. In the UK, ambient air is already monitored under the UK Heavy Metals Monitoring Network for a number of heavy metals, including nickel (Ni), arsenic (As), cadmium (Cd) and lead (Pb) to ensure compliance with legislative limits. However, the UK Expert Panel on Air Quality Standards (EPAQS) has highlighted a need to limit concentrations of beryllium (Be) in air, which is not currently monitored, because of its toxicity. The aim of this work was to analyse airborne particulate matter (PM) sampled onto filter papers from the UK Heavy Metals Monitoring Network for quantitative, trace level beryllium determination and compare the results to the guideline concentration specified by EPAQS. Samples were prepared by microwave acid digestion in a matrix of 2% sulphuric acid and 14% nitric acid, verified by the use of Certified Reference Materials (CRMs). The digested samples were then analysed by Inductively Coupled Plasma Mass Spectrometry (ICP-MS). The filters from the UK Heavy Metals Monitoring Network were tested using this procedure and the average beryllium concentration across the network for the duration of the study period was 7.87 pg m-3. The highest site average concentration was 32.0 pg m-3 at Scunthorpe Low Santon, which is significantly lower than levels that are thought to cause harm. However the highest levels were observed at sites monitoring industrial point sources, indicating that beryllium is being used and emitted, albeit at very low levels, from these point sources. Comparison with other metals concentrations and data from the UK National Atmospheric Emissions Inventory suggests that current emissions of beryllium may be significantly overestimated.

  10. Unsuspected exposure to beryllium: potential implications for sarcoidosis diagnoses.

    Science.gov (United States)

    Laczniak, Andrew N; Gross, Nathan A; Fuortes, Laurence J; Field, R William

    2014-07-21

    Exposure to Beryllium (Be) can cause sensitization (BeS) and chronic beryllium disease (CBD) in some individuals.  Even relatively low exposures may be sufficient to generate an asymptomatic, or in some cases a symptomatic, immune response. Since the clinical presentation of CBD is similar to that of sarcoidosis, it is helpful to have information on exposure to beryllium in order to reduce misdiagnosis. The purpose of this pilot study is to explore the occurrence of Be surface deposits at worksites with little or no previous reported use of commercially available Be products.  The workplaces chosen for this study represent a convenience sample of businesses in eastern Iowa. One hundred thirty-six surface dust samples were collected from 27 businesses for analysis of Be. The results were then divided into categories by the amount of detected Be according to U.S. Department of Energy guidelines as described in 10 CFR 850.30 and 10 CFR 850.31. Overall, at least one of the samples at 78% of the work sites tested contained deposited Be above the analytical limit of quantitation (0.035 µg beryllium per sample).  Beryllium was detected in 46% of the samples collected. Twelve percent of the samples exceeded 0.2 µg/100 cm² and 4% of the samples exceeded a Be concentration of 3 µg/100 cm². The findings from this study suggest that there may be a wider range and greater number of work environments that have the potential for Be exposure than has been documented previously.  These findings could have implications for the accurate diagnosis of sarcoidosis.

  11. Mechanical Properties of Aluminum-Copper Joint by Laser Penetration Brazing%铝-铜异种金属激光深熔钎焊接头力学性能

    Institute of Scientific and Technical Information of China (English)

    董鹏; 陈凯华; 肖荣诗

    2011-01-01

    采用Yb:YAG盘式激光器进行3 mm厚1060铝合金-T2紫铜异种金属激光深熔钎焊试验,并用显微硬度测试以及静载拉伸试验对接头的力学性能进行评价.由于焊缝中晶粒细小且含有硬度较高的AlCu以及A1Cu金属间化合物,其显微硬度要高于铝、铜母材.接头的抗拉强度可以达到铝母材的94%以上,拉伸试验的结果具有一定随机性,其中试样最大的抗拉强度为100.6 MPa,断裂发生在铝合金母材;断裂在焊缝界面处的试样的抗拉强度为94.5 MPa.由于在过渡层内存在硬度和脆性较大的金属间化合物过渡层,与焊缝其他部分存在硬度梯度,在拉伸过程中过渡层处容易出现裂纹,形成断裂.%1060 aluminum alloy and T2 copper with the thickness of 3 mm are joined by means of laser penetrationbrazing (LPB) with a Yb: YAG disc laser. The mechanical properties of the joint are measured by microhardness and tensile tests. The microhardness of the weld is higher than that of aluminum and copper base metals, respectively,due to the formation of fine grains and hard Al2Cu and Al2Cu3 intermetallic compounds. The results of the tensile tests for welded samples are variational under the same parameters. The maximum failure strength for tensile test is 100.6 MPa. The failure occurres at aluminum side. The minimum failure strength is 94. 5 MPa. The failure happens close to the interface due to the hardness gradient and brittle intermetallic compounds.

  12. Evaluation of historical beryllium abundance in soils, airborne particulates and facilities at Lawrence Livermore National Laboratory.

    Science.gov (United States)

    Sutton, Mark; Bibby, Richard K; Eppich, Gary R; Lee, Steven; Lindvall, Rachel E; Wilson, Kent; Esser, Bradley K

    2012-10-15

    Beryllium has been historically machined, handled and stored in facilities at Lawrence Livermore National Laboratory (LLNL) since the 1950s. Additionally, outdoor testing of beryllium-containing components has been performed at LLNL's Site 300 facility. Beryllium levels in local soils and atmospheric particulates have been measured over three decades and are comparable to those found elsewhere in the natural environment. While localized areas of beryllium contamination have been identified, laboratory operations do not appear to have increased the concentration of beryllium in local air or water. Variation in airborne beryllium correlates to local weather patterns, PM10 levels, normal sources (such as resuspension of soil and emissions from coal power stations) but not to LLNL activities. Regional and national atmospheric beryllium levels have decreased since the implementation of the EPA's 1990 Clean-Air-Act. Multi-element analysis of local soil and air samples allowed for the determination of comparative ratios for beryllium with over 50 other metals to distinguish between natural beryllium and process-induced contamination. Ten comparative elemental markers (Al, Cs, Eu, Gd, La, Nd, Pr, Sm, Th and Tl) that were selected to ensure background variations in other metals did not collectively interfere with the determination of beryllium sources in work-place samples at LLNL. Multi-element analysis and comparative evaluation are recommended for all workplace and environmental samples suspected of beryllium contamination. The multi-element analyses of soils and surface dusts were helpful in differentiating between beryllium of environmental origin and beryllium from laboratory operations. Some surfaces can act as "sinks" for particulate matter, including carpet, which retains entrained insoluble material even after liquid based cleaning. At LLNL, most facility carpets had beryllium concentrations at or below the upper tolerance limit determined by sampling facilities

  13. Geochemistry, geochronology, mineralogy, and geology suggest sources of and controls on mineral systems in the southern Toquima Range, Nye County, Nevada; with geochemistry maps of gold, silver, mercury, arsenic, antimony, zinc, copper, lead, molybdenum, bismuth, iron, titanium, vanadium, cobalt, beryllium, boron, fluorine, and sulfur; and with a section on lead associations, mineralogy and paragenesis, and isotopes

    Science.gov (United States)

    Shawe, Daniel R.; Hoffman, James D.; Doe, Bruce R.; Foord, Eugene E.; Stein, Holly J.; Ayuso, Robert A.

    2003-01-01

    distribution patterns that suggest specific sources and lithologic influences on deposition, as well as multiple episodes of mineralization. Principal episodes of mineralization are Late Cretaceous (molybdenum and tungsten in and near granite; silver at Belmont and Silver Point mines), early Oligocene [tourmaline and base- and precious-metals around the granodiorite of Dry Canyon stock as well as at Manhattan(?)], late Oligocene (gold at Round Mountain and Jefferson), and Miocene (gold at Manhattan). Most likely principal sources of molybdenum, tungsten, silver, and bismuth are Cretaceous granites; of antimony, arsenic, and mercury are intermediate-composition early Oligocene intrusives; and of gold are early and late Oligocene and early Miocene magmas of the volcanic cycle. Lead may have been derived principally from Cretaceous granitic magma and Paleozoic sedimentary rocks. Several areas prospective for undiscovered mineral deposits are suggested by spatial patterns of element distributions related to geologic features. The Manhattan district in the vicinity of the White Caps mine may be underlain by a copper-molybdenum porphyry system related to a buried stock; peripheral high-grade gold veins and skarn deposits may be present below deposits previously mined. The Jefferson district also may be underlain by a copper-molybdenum porphyry system related to a buried stock, it too with peripheral high-grade gold deposits. The Bald Mountain Canyon belt of small gold veins has potential for deeper deposits in buried porous ash-flow tuff similar to the huge Round Mountain low-grade gold-silver deposit. Several other areas have potential for a variety of mineral deposits. Altogether the geochemical, geochronologic, mineralogic, and geologic evidence suggests recurring mineralizing episodes of varied character, from Late Cretaceous to late Tertiary time, related to a long-lived hot spot deep in the crust or in the upper mantle. Granite plutons of Late Cretaceous age were minerali

  14. Beryllium detection in human lung tissue using electron probe X-ray microanalysis.

    Science.gov (United States)

    Butnor, Kelly J; Sporn, Thomas A; Ingram, Peter; Gunasegaram, Sue; Pinto, John F; Roggli, Victor L

    2003-11-01

    Chronic berylliosis is an uncommon disease that is caused by the inhalation of beryllium particles, dust, or fumes. The distinction between chronic berylliosis and sarcoidosis can be difficult both clinically and histologically, as both entities can have similar presentations and exhibit nonnecrotizing granulomatous inflammation of the lungs. The diagnosis of chronic berylliosis relies on a history of exposure to beryllium, roentgenographic evidence of diffuse nodular disease, and demonstration of beryllium hypersensitivity by ancillary studies, such as lymphocyte proliferation testing. Additional support may be gained by the demonstration of beryllium in lung tissue. Unlike other exogenous particulates, such as asbestos, detection of beryllium in human lung tissue is problematic. The low atomic number of beryllium usually makes it unsuitable for conventional microprobe analysis. We describe a case of chronic berylliosis in which beryllium was detected in lung tissue using atmospheric thin-window energy-dispersive X-ray analysis (ATW EDXA). A woman with a history of occupational exposure to beryllium at a nuclear weapons testing facility presented with progressive cough and dyspnea and a nodular pattern on chest roentgenograph. Open lung biopsy showed nonnecrotizing granulomatous inflammation that was histologically indistinguishable from sarcoidosis. Scanning electron microscopy and ATW EDXA demonstrated particulates containing beryllium within the granulomas. This application of EDXA offers significant advantages over existing methods of beryllium detection in that it is nondestructive, more widely available, and can be performed using routine paraffin sections.

  15. Beryllium alters lipopolysaccharide-mediated intracellular phosphorylation and cytokine release in human peripheral blood mononuclear cells.

    Science.gov (United States)

    Silva, Shannon; Ganguly, Kumkum; Fresquez, Theresa M; Gupta, Goutam; McCleskey, T Mark; Chaudhary, Anu

    2009-12-01

    Beryllium exposure in susceptible individuals leads to the development of chronic beryllium disease, a lung disorder marked by release of inflammatory cytokine and granuloma formation. We have previously reported that beryllium induces an immune response even in blood mononuclear cells from healthy individuals. In this study, we investigate the effects of beryllium on lipopolysaccharide-mediated cytokine release in blood mononuclear and dendritic cells from healthy individuals. We found that in vitro treatment of beryllium sulfate inhibits the secretion of lipopolysaccharide-mediated interleukin 10, while the release of interleukin 1beta is enhanced. In addition, not all lipopolysaccharide-mediated responses are altered, as interleukin 6 release in unaffected upon beryllium treatment. Beryllium sulfate-treated cells show altered phosphotyrosine levels upon lipopolysaccharide stimulation. Significantly, beryllium inhibits the phosphorylation of signal transducer and activator of transducer 3, induced by lipopolysaccharide. Finally, inhibitors of phosphoinositide-3 kinase mimic the effects of beryllium in inhibition of interleukin 10 release, while they have no effect on interleukin 1beta secretion. This study strongly suggests that prior exposures to beryllium could alter host immune responses to bacterial infections in healthy individuals, by altering intracellular signaling.

  16. 国内外铍及含铍材料的研究进展%Advances in beryllium and beryllium-containing materials

    Institute of Scientific and Technical Information of China (English)

    许德美; 秦高梧; 李峰; 王战宏; 钟景明; 何季麟; 何力军

    2014-01-01

    The research progress of beryllium and beryllium-containing materials was reviewed in the past two decades in the world, and much effort in this work was focused on beryllium metallurgy, beryllium alloys, beryllium oxide, beryllium matrix composites and intermetallics. The advances of beryllium materials in both research and production techniques in China were summarized, especially in technique gap as compared to that in the developed countries. Finally, the new beryllium materials and their key techniques conforming to the requirements of industry were proposed in the next one decade in China.%综述近20年来国外铍及含铍材料的研究进展,主要包括铍的冶金制备、铍合金、铍和氧化铍金属基复合材料、铍金属间化合物等。概括我国在铍材料方面取得的研究与生产技术进展,以及与国外研发水平的差距。并展望未来10年我国铍及含铍材料需要重点发展的新材料以及突破的关键技术。

  17. Investigations of the ternary system beryllium-carbon-tungsten and analyses of beryllium on carbon surfaces; Untersuchung des ternaeren Systems Beryllium-Kohlenstoff-Wolfram und Betrachtungen von Beryllium auf Kohlenstoffoberflaechen

    Energy Technology Data Exchange (ETDEWEB)

    Kost, Florian

    2009-05-25

    Beryllium, carbon and tungsten are planned to be used as first wall materials in the future fusion reactor ITER. The aim of this work is a characterization of mixed material formation induced by thermal load. To this end, model systems (layers) were prepared and investigated, which give insight into the basic physical and chemical concepts. Before investigating ternary systems, the first step was to analyze the binary systems Be/C and Be/W (bottom-up approach), where the differences between the substrates PG (pyrolytic graphite) and HOPG (highly oriented pyrolytic graphite) were of special interest. Particularly X-ray photoelectron spectroscopy (XPS), low energy ion scattering (ISS) and Rutherford backscattering spectroscopy (RBS) were used as analysis methods. Beryllium evaporated on carbon shows an island growth mode, whereas a closed layer can be assumed for layer thicknesses above 0.7 nm. Annealing of the Be/C system induces Be{sub 2}C island formation for T{>=}770 K. At high temperatures (T{>=}1170 K), beryllium carbide dissociates, resulting in (metallic) beryllium desorption. For HOPG, carbide formation starts at higher temperatures compared to PG. Activation energies for the diffusion processes were determined by analyzing the decreasing beryllium amount versus annealing time. Surface morphologies were characterized using angle-resolved XPS (ARXPS) and atomic force microscopy (AFM). Experiments were performed to study processes in the Be/W system in the temperature range from 570 to 1270 K. Be{sub 2}W formation starts at 670 K, a complete loss of Be{sub 2}W is observed at 1170 K due to dissociation (and subsequent beryllium desorption). Regarding ternary systems, particularly Be/C/W and C/Be/W were investigated, attaching importance to layer thickness (reservoir) variations. At room temperature, Be{sub 2}C, W{sub 2}C, WC and Be{sub 2}W formation at the respective interfaces was observed. Further Be{sub 2}C is forming with increasing annealing temperatures

  18. Effect of Bonding Temperature on Phase Transformation of Diffusion-Bonded Joints of Duplex Stainless Steel and Ti-6Al-4V Using Nickel and Copper as Composite Intermediate Metals

    Science.gov (United States)

    Kundu, Sukumar; Thirunavukarasu, Gopinath; Chatterjee, Subrata; Mishra, Brajendra

    2015-12-01

    In the present study, the effect of bonding temperature on phase transformation of diffusion-bonded joints of duplex stainless steel (DSS) and Ti-6Al-4V (Ti64) using simultaneously both nickel (Ni) and copper (Cu) interlayers was investigated in the temperature range of 1148 K to 1223 K (875 °C to 950 °C) insteps of 25 K (25 °C) for 60 minutes under 4 MPa uniaxial pressure in vacuum. Interfaces were characterized by scanning electron microscopy and interdiffusion of the chemical species across the diffusion interfaces were witnessed by electron probe microanalysis. At 1148 K (875 °C), layer-wise Cu4Ti, Cu2Ti, Cu4Ti3, CuTi, and CuTi2 phases were observed at the Cu-Ti64 interface; however, DSS-Ni and Ni-Cu interfaces were free from any intermetallic. At 1173 K and 1198 K (900 °C and 925 °C), Cu interlayer could not restrict the diffusion of atoms from Ti64 to Ni, and vice versa; and Ni-Ti-based intermetallics were formed at the Ni-Cu interface and throughout the Cu zone as well; however, at 1223 K (950 °C), both Ni and Cu interlayers could not inhibit the diffusion of atoms from Ti64 to DSS, and vice versa. The maximum shear strength of ~377 MPa was obtained for the diffusion couple processed at 1148 K (875 °C) and strength of the bonded joints gradually decreased with the increasing bonding temperature due to the widening of brittle intermetallics at the diffusion zone. Fracture path indicated that failure took place through the Cu4Ti intermetallic at the Cu-Ti64 interface when bonding was processed at 1148 K (875 °C). When bonding was processed at 1173 K and 1198 K (900 °C and 925 °C), fracture took place through the Ni3Ti intermetallic at the Ni-(Ni + Cu + Ti64 diffusion reaction) interface; however, at 1223 K (950 °C), fracture morphology indicated the brittle nature and the fracture took place apparently through the σ phase at the DSS-(DSS + Ni + Cu + Ti64 diffusion reaction) interface.

  19. JET-ISX-B beryllium limiter experiment safety analysis report and operational safety requirements

    Energy Technology Data Exchange (ETDEWEB)

    Edmonds, P.H.

    1985-09-01

    An experiment to evaluate the suitability of beryllium as a limiter material has been completed on the ISX-B tokamak. The experiment consisted of two phases: (1) the initial operation and characterization in the ISX experiment, and a period of continued operation to the specified surface fluence (10/sup 22/ atoms/cm/sup 2/) of hydrogen ions; and (2) the disassembly, decontamination, or disposal of the ISX facility. During these two phases of the project, the possibility existed for beryllium and/or beryllium oxide powder to be produced inside the vacuum vessel. Beryllium dust is a highly toxic material, and extensive precautions are required to prevent the release of the beryllium into the experimental work area and to prevent the contamination of personnel working on the device. Details of the health hazards associated with beryllium and the appropriate precautions are presented. Also described in appendixes to this report are the various operational safety requirements for the project.

  20. Beryllium Dust Generation in PISCES-B Due to Plasma-Material Interactions

    Science.gov (United States)

    Doerner, R.; Mays, C.; Hirooka, Y.; Luckhardt, S. C.; Sze, C. F.; Won, J.; Conn, R. W.

    1996-11-01

    The PISCES-B device has started plasma-beryllium experiments in its new location at U.C. San Diego. An improved controlled atmosphere enclosure was constructed to assure safe operation with beryllium materials. In the previous experimental campaign we found that a total of 600 mg of beryllium had been eroded during materials tests. This provided us with a unique opportunity to investigate the lost beryllium. Swipe sampling and vacuum sampling of the PISCES-B vacuum chamber revealed that 3% of the eroded beryllium resided as uniformly distributed loose dust within the vacuum chamber. An additional 33% of the eroded beryllium was coated onto the chamber wall. Filtering through a series of decreasing pore size meshes revealed a uniform distribution of particle sizes in the respirable range (between 10mm - 0.1mm), fewer larger particles (>50mm) were observed. This work is supported by USDOE under grant DE-FG03-95ER-54301.

  1. Studies on extraction of beryllium from thiocyanate solutions by quaternary ammonium halides.

    Science.gov (United States)

    El-Yamani, I S; El-Messieh, E N

    A 0.4M tricaprylmethylammonium chloride solution in n-hexane was used for the quantitative extraction of beryllium from hydrochloric acid (pH 3) and 5M potassium thiocyanate. Beryllium was stripped from the organic phase with 1M sodium hydroxide, then determined volumetrically with bismuthyl perchlorate and bromocresol green indicator. Beryllium was extracted in presence of a large number of elements which are usually associated with it in beryl and in fission products of nuclear fuel.

  2. Quality management of dispersion-strengthened beryllium-based composite alloy

    Directory of Open Access Journals (Sweden)

    Дмитро Миколайович Макаренко

    2016-05-01

    Full Text Available The article is devoted to investigation of the composition and properties of dispersion-strengthened beryllium-based composite alloy, used in various industries, including the aircraft manufacture aircraft. Analyzed the properties of these materials are analyzed to ensure their quality management. The mathematical relationship of dispersion strengthened beryllium-based composite alloy parameters from content of beryllium oxide and temperature are built

  3. Summary of historical beryllium uses and airborne concentration levels at Los Alamos National Laboratory.

    Science.gov (United States)

    Stefaniak, Aleksandr B; Weaver, Virginia M; Cadorette, Maureen; Puckett, Leslie G; Schwartz, Brian S; Wiggs, Laurie D; Jankowski, Mark D; Breysse, Patrick N

    2003-09-01

    Beryllium operations and accompanying medical surveillance of workers at Los Alamos National Laboratory began in the 1940s. In 1999 a Former Workers Medical Surveillance Program that includes screening for chronic beryllium disease was initiated. As part of this program, historical beryllium exposure conditions were reconstructed from archived paper and electronic industrial hygiene data sources to improve understanding of past beryllium uses and airborne concentration levels. Archived industrial hygiene sampling reports indicated beryllium was principally used in technical areas-01 and -03, primarily being machined. Beryllium was also used at 15 other technical areas in activities that ranged from explosives detonation to the manufacture of X-ray windows. A total of 4528 personal breathing zone and area air samples for beryllium, combined for purposes of calculating summary statistics, were identified during the records review phase. The geometric mean airborne beryllium concentration for the period 1949-1989 for all technical areas was 0.04 microg Be/m(3) with 97 percent of all sample below the 2.0 microg Be/m(3) occupational exposure limit (OEL). Average beryllium concentrations per decade were less than 1 microg Be/m(3) and annual geometric mean concentrations in technical area-03, the largest user of beryllium, were generally below 0.1 microg Be/m(3), indicating exposure was generally well-controlled, that is, below the OEL. Typical of many retrospective exposure assessments, not all archived data could be extracted and summarized. Despite this, we report a reasonable summary of potential beryllium uses and airborne concentration levels a worker may have encountered from 1949-1989. These data can be used to more effectively identify former worker populations at potential risk for chronic beryllium disease and to offer these workers screening as part of the Former Worker Medical Surveillance Program, and in the event that a case is diagnosed, help to understand

  4. Beryllium uptake and related biological effects studied in THP-1 differentiated macrophages.

    Science.gov (United States)

    Ding, Jian; Lin, Lin; Hang, Wei; Yan, Xiaomei

    2009-11-01

    Investigation of cellular uptake of metal compounds is important in understanding metal-related toxicity and diseases. Inhalation of beryllium aerosols can cause chronic beryllium disease, a progressive, granulomatous fibrosis of the lung. Studies in laboratory animals and cultured animal cells indicate that alveolar macrophages take up beryllium compounds and participate in a hypersensitivity immune response to a beryllium-containing antigen. In the present work, human monocyte cell line THP-1 was induced with phorbol myristate acetate to differentiate into a macrophage. This cell with characteristics of human alveolar macrophages was employed to study cellular beryllium uptake and related biological effects. Morphological changes, phagocytosis of fluorescent latex beads, and cell surface CD14 expression were used to verify the successful differentiation of THP-1 monocytes into macrophages. An improved mass spectrometry method for quantitative analysis of intracellular beryllium as opposed to the traditional radioisotopic approach was developed using ICP-MS. The influence of the solubility of beryllium compounds, exposure duration, and beryllium concentration on the incorporation of beryllium was studied. Our data indicated that the uptake of particulate BeO was much more significant than that of soluble BeSO(4), suggesting the major cellular uptake pathway is phagocytosis. Nevertheless, subsequent DAPI nuclear staining and PARP cleavage study indicated that beryllium uptake had a negligible effect on the apoptosis of THP-1 macrophages compared to the unstimulated macrophage control. Meanwhile, no substantial variation of tumour necrosis factor-alpha production was observed for THP-1 macrophages upon beryllium exposure. These data imply alveolar macrophages could have some level of tolerance to beryllium and this may explain why most Be-exposed individuals remain healthy throughout life.

  5. Minority Carrier Lifetime in Beryllium-Doped InAs/InAsSb Strained Layer Superlattices

    Science.gov (United States)

    2014-06-03

    SECURITY CLASSIFICATION OF: Minority carrier lifetimes in undoped and Beryllium -doped Type-2 Ga-free, InAs/InAsSb strained layer superlattices (SLS) with...is unlimited. Minority Carrier Lifetime in Beryllium -Doped InAs/InAsSb Strained Layer Superlattices The views, opinions and/or findings contained in...Brook University W-5510 Melville Library West Sayville, NY 11796 -3362 1 ABSTRACT Minority Carrier Lifetime in Beryllium -Doped InAs/InAsSb Strained

  6. Beryllium dimer: a bond based on non-dynamical correlation.

    Science.gov (United States)

    El Khatib, Muammar; Bendazzoli, Gian Luigi; Evangelisti, Stefano; Helal, Wissam; Leininger, Thierry; Tenti, Lorenzo; Angeli, Celestino

    2014-08-21

    The bond nature in beryllium dimer has been theoretically investigated using high-level ab initio methods. A series of ANO basis sets of increasing quality, going from sp to spdf ghi contractions, has been employed, combined with HF, CAS-SCF, CISD, and MRCI calculations with several different active spaces. The quality of these calculations has been checked by comparing the results with valence Full-CI calculations, performed with the same basis sets. It is shown that two quasi-degenerated partly occupied orbitals play a crucial role to give a qualitatively correct description of the bond. Their nature is similar to that of the edge orbitals that give rise to the quasi-degenerated singlet-triplet states in longer beryllium chains.

  7. Fabricating thin beryllium windows for X-ray applications

    Science.gov (United States)

    Truhan, John J.; Wagner, Lawrence M.

    1980-10-01

    X-ray windows for diagnostics into vacuum chambers are commonly made of beryllium, which must be as thin as possible to minimize attenuation of the X rays. The windows must be bonded to mounting flanges, and the bond must be leak-tight and able to withstand a pressure differential of one atmosphere. A solid-state bonding process can be used to attach windows of thickness from 0.025 down to 0.015 mm. The process bonds the beryllium window, a silver intermediate layer, and the mounting flange together using compression and heat. The process is not sensitive to the bonding parameters; usual ranges are: pressures of 83-172 MPa, temperatures of 750-950 K, and holding times of 5-60 min. Unsuccessful bonds can often be repaired, or parts can be salvaged for re-use. A variety of window geometries can be accommodated.

  8. Beryllium Drive Disc Characterization for Laboratory Astrophysics Experiments

    Science.gov (United States)

    Ditmar, J. R.; Drake, R. P.; Kuranz, C. C.; Grosskopf, M. J.

    2009-11-01

    Laboratory Astrophysics scales large-scale phenomena, such as core-collapse supernovae shocks, down to the sub-millimeter scale for investigation in a laboratory setting. In some experiments, targets are constructed with a 20μm thick beryllium disc attached to a polyimide tube. A shockwave is created by irradiating the Be disc with ˜ 4kJ of energy from the Omega Laser. The Be material is rolled into a 20μm sheet and then machined to a 2.5mm diameter. Characterizing the roughness and knowing if there are any major features on the initial surface could affect interpretations of data taken during experiments. Structure in the Beryllium discs could become an important parameter in future high-fidelity computer simulations. Surfaces were characterized with a Scanning Electron Microscope and an Atomic Force Microscope.

  9. VLT beryllium secondary mirror no. 1: performance review

    Science.gov (United States)

    Cayrel, Marc

    1998-08-01

    The four Very Large Telescope secondary mirrors are 1.2-m Beryllium lightweight convex mirrors. REOSC has been selected for the design and manufacturing of the optics and of their supporting system. The first mirror unit has been delivered in September, 1997. Operating from visible to near infrared, the mirror defines the telescope aperture stop and may be chopped during observation. The optical requirements are tight and a high stiffness, low weight and inertia are requested as well. Using beryllium is a technical challenge for such a large optic manufacturing, in particular regarding its stability. The requirements and design are presented, we review the mirror manufacturing steps: blank production, machining, grinding, Nickel plating, polishing, integration and testing. The optical quality control method, a problem for large convex mirrors control, is detailed. The results of acceptance testing of mirror No. 1 are summarized, we present conclusions about the mirror figure stability. The status of the three additional mirrors manufacturing is presented to conclude.

  10. Multiscale modelling of hydrogen behaviour on beryllium (0001 surface

    Directory of Open Access Journals (Sweden)

    Ch. Stihl

    2016-12-01

    Full Text Available Beryllium is proposed to be a neutron multiplier and plasma facing material in future fusion devices. Therefore, it is crucial to acquire an understanding of the microscopic mechanisms of tritium accumulation and release as a result of transmutation processes that Be undergoes under neutron irradiation. A multiscale simulation of ad- and desorption of hydrogen isotopes on the beryllium (0001 surface is developed. It consists of ab initio calculations of certain H adsorption configurations, a suitable cluster expansion approximating the energies of arbitrary configurations, and a kinetic Monte Carlo method for dynamic simulations of adsorption and desorption. The processes implemented in the kinetic Monte Carlo simulation are deduced from further ab initio calculations comprising both, static relaxation as well as molecular dynamics runs. The simulation is used to reproduce experimental data and the results are compared and discussed. Based on the observed results, proposals for a refined model are made.

  11. Beryllium Concentrations at European Workplaces: Comparison of 'Total' and Inhalable Particulate Measurements.

    Science.gov (United States)

    Kock, Heiko; Civic, Terence; Koch, Wolfgang

    2015-07-01

    A field study was carried out in order to derive a factor for the conversion of historic worker exposure data on airborne beryllium (Be) obtained by sampling according to the 37-mm closed faced filter cassette (CFC) 'total' particulate method into exposure concentration values to be expected when sampling using the 'Gesamtstaubprobenahmesystem' (GSP) inhalable sampling convention. Workplaces selected to represent the different copper Be work processing operations that typically occur in Germany and the EU were monitored revealing a broad spectrum of prevailing Be size distributions. In total, 39 personal samples were taken using a 37-mm CFC and a GSP worn side by side for simultaneous collection of the 'total' dust and the inhalable particulates, respectively. In addition, 20 static general area measurements were carried out using GSP, CFC, and Respicon samplers in parallel, the latter one providing information on the extra-thoracic fraction of the workplace aerosol. The study showed that there is a linear relationship between the concentrations measured with the CFC and those measured with the GSP sampler. The geometric mean value of the ratios of time-weighted average concentrations determined from GSP and CFC samples of all personal samples was 2.88. The individual values covered a range between 1 and 17 related to differences in size distributions of the Be-containing particulates. This was supported by the area measurements showing that the conversion factor increases with increasing values of the extra-thoracic fraction covering a range between 0 and 79%.

  12. Beryllium, Lithium and Oxygen Abundances in F-type Stars

    CERN Document Server

    García-López, R J; Pérez de Taoro, M R; Casares, C; Rasilla, J L; Rebolo, R; Allende-Prieto, C

    1997-01-01

    Beryllium and oxygen abundances have been derived in a sample of F-type field stars for which lithium abundances had been measured previously, with the aim of obtaining observational constraints to discriminate between the different mixing mechanisms proposed. Mixing associated with the transport of angular momentum in the stellar interior and internal gravity waves within the framework of rotating evolutionary models, appear to be promising ways to explain the observations.

  13. Presence of Beryllium (Be) in urban soils: human health risk

    Energy Technology Data Exchange (ETDEWEB)

    Pena, A.; Gonzalez, M. J.; Lobo, M. C.

    2009-07-01

    Berylium (Be) is, together with As, Cd, Hg, Pb and Ti, one of the trace elements more toxic for human being (Vaessen) and Szteke, 2000; Yaman and Avci, 2006), but in spite of the exponential increment of its applications during the last decades, surprisingly there isn't hardly information about its presence and environmental distribution. The aim of this work is to evaluate the presence of Beryllium in urban soils in Alcala de Henares, (Madrid Spain).

  14. Impact of HFIR LEU Conversion on Beryllium Reflector Degradation Factors

    Energy Technology Data Exchange (ETDEWEB)

    Ilas, Dan [ORNL

    2013-10-01

    An assessment of the impact of low enriched uranium (LEU) conversion on the factors that may cause the degradation of the beryllium reflector is performed for the High Flux Isotope Reactor (HFIR). The computational methods, models, and tools, comparisons with previous work, along with the results obtained are documented and discussed in this report. The report documents the results for the gas and neutronic poison production, and the heating in the beryllium reflector for both the highly enriched uranium (HEU) and LEU HFIR configurations, and discusses the impact that the conversion to LEU may have on these quantities. A time-averaging procedure was developed to calculate the isotopic (gas and poisons) production in reflector. The sensitivity of this approach to different approximations is gauged and documented. The results show that the gas is produced in the beryllium reflector at a total rate of 0.304 g/cycle for the HEU configuration; this rate increases by ~12% for the LEU case. The total tritium production rate in reflector is 0.098 g/cycle for the HEU core and approximately 11% higher for the LEU core. A significant increase (up to ~25%) in the neutronic poisons production in the reflector during the operation cycles is observed for the LEU core, compared to the HEU case, for regions close to the core s horizontal midplane. The poisoning level of the reflector may increase by more than two orders of magnitude during long periods of downtime. The heating rate in the reflector is estimated to be approximately 20% lower for the LEU core than for the HEU core. The decrease is due to a significantly lower contribution of the heating produced by the gamma radiation for the LEU core. Both the isotopic (gas and neutronic poisons) production and the heating rates are spatially non-uniform throughout the beryllium reflector volume. The maximum values typically occur in the removable reflector and close to the midplane.

  15. The beryllium quandary: will the lower exposure limits spur new developments in sampling and analysis?

    Energy Technology Data Exchange (ETDEWEB)

    Brisson, Michael

    2013-06-03

    At the time this article was written, new rulemakings were under consideration at OSHA and the U.S. Department of Energy (DOE) that would propose changes to occupational exposure limits for beryllium. Given these developments, it’s a good time to review the tools and methods available to IHs for assessing beryllium air and surface contamination in the workplace—what’s new and different, and what’s tried and true. The article discusses limit values and action levels for beryllium, problematic aspects of beryllium air sampling, sample preparation, sample analysis, and data evaluation.

  16. Proteomic analysis of beryllium-induced genotoxicity in an Escherichia coli mutant model system.

    Science.gov (United States)

    Taylor-McCabe, Kirsten J; Wang, Zaolin; Sauer, Nancy N; Marrone, Babetta L

    2006-03-01

    Beryllium is the second lightest metal, has a high melting point and high strength-to-weight ratio, and is chemically stable. These unique chemical characteristics make beryllium metal an ideal choice as a component material for a wide variety of applications in aerospace, defense, nuclear weapons, and industry. However, inhalation of beryllium dust or fumes induces significant health effects, including chronic beryllium disease and lung cancer. In this study, the mutagenicity of beryllium sulfate (BeSO(4)) and the comutagenicity of beryllium with a known mutagen 1-methyl-3-nitro-1-nitrosoguanidine (MNNG) were evaluated using a forward mutant detection system developed in Escherichia coli. In this system, BeSO(4) was shown to be weakly mutagenic alone and significantly enhanced the mutagenicity of MNNG up to 3.5-fold over MNNG alone. Based on these results a proteomic study was conducted to identify the proteins regulated by BeSO(4). Using the techniques of 2-DE and oMALDI-TOF MS, we successfully identified 32 proteins being differentially regulated by beryllium and/or MNNG in the E. coli test system. This is the first study to describe the proteins regulated by beryllium in vitro, and the results suggest several potential pathways for the focus of further research into the mechanisms underlying beryllium-induced genotoxicity.

  17. Chest wall shrapnel-induced beryllium-sensitization and associated pulmonary disease.

    Science.gov (United States)

    Fireman, E; Shai, A Bar; Lerman, Y; Topilsky, M; Blanc, P D; Maier, L; Li, L; Chandra, S; Abraham, J M; Fomin, I; Aviram, G; Abraham, J L

    2012-10-01

    Chronic beryllium disease (CBD) is an exposure-related granulomatous disease mimicking sarcoidosis. Beryllium exposure-associated disease occurs mainly via inhalation, but skin may also be a source of sensitization. A 65-year-old male with a history of war-related shrapnel wounds was initially diagnosed with pulmonary sarcoidosis. Twenty years later, the possibility of a metal-related etiology for the lung disease was raised. A beryllium lymphocyte proliferation test, elemental analysis of removed shrapnel, and genetic studies were consistent with a diagnosis of CBD. This case demonstrates that retained beryllium-containing foreign bodies can be linked to a pathophysiologic response in the lung consistent with CBD.

  18. Calculations for electron-impact excitation and ionization of beryllium

    Science.gov (United States)

    Zatsarinny, Oleg; Bartschat, Klaus; Fursa, Dmitry V.; Bray, Igor

    2016-12-01

    The B-spline R-matrix and the convergent close-coupling methods are used to study electron collisions with neutral beryllium over an energy range from threshold to 100 eV. Coupling to the target continuum significantly affects the results for transitions from the ground state, but to a lesser extent the strong transitions between excited states. Cross sections are presented for selected transitions between low-lying physical bound states of beryllium, as well as for elastic scattering, momentum transfer, and ionization. The present cross sections for transitions from the ground state from the two methods are in excellent agreement with each other, and also with other available results based on nonperturbative convergent pseudostate and time-dependent close-coupling models. The elastic cross section at low energies is dominated by a prominent shape resonance. The ionization from the {(2s2p)}3P and {(2s2p)}1P states strongly depends on the respective term. The current predictions represent an extensive set of electron scattering data for neutral beryllium, which should be sufficient for most modeling applications.

  19. A diethylhydroxylaminate based mixed lithium/beryllium aggregate

    Energy Technology Data Exchange (ETDEWEB)

    Berger, Raphael J.F. [Paris-Lodron Universitaet Salzburg (Austria). Fachbereich fuer Materialwissenschaften und Physik; Jana, Surajit [Asansol Girls College, West-Bengal (India). Dept. of Chemistry; Froehlich, Roland [Muenster Univ. (Germany). Organisch-Chemisches Inst.; Mitzel, Norbert W. [Bielefeld Univ. (Germany). Anorganische Chemie und Strukturchemie

    2015-07-01

    A mixed lithium/beryllium diethylhydroxylaminate compound containing {sup n}butyl beryllium units of total molecular composition {sup n}Be(ONEt{sub 2}){sub 2} [(LiONEt{sub 2}){sup 2} {sup n}BuBeONEt{sub 2}]{sub 2} (1) was isolated from a reaction mixture of {sup n}butyl lithium, N,N-diethylhydroxylamine and BeCl{sub 2} in diethylether/thf. The crystal structure of 1 has been determined by X-ray diffraction. The aggregate is composed of two ladder-type subunits connected in a beryllium-centered distorted tetrahedron of four oxygen atoms. Only the lithium atoms are engaged in coordination with the nitrogen donor atoms. The DFT calculations support the positional occupation determined for Li and Be in the crystal structure. The DFT and the solid-state structure are in excellent agreement, indicating only weak intermolecular interactions in the solid state. Structural details of metal atom coordination are discussed.

  20. Introduction to beryllium: uses, regulatory history, and disease.

    Science.gov (United States)

    Kolanz, M E

    2001-05-01

    Beryllium is an ubiquitous element in the environment, and it has many commercial applications. Because of its strength, electrical and thermal conductivity, corrosion resistance, and nuclear properties, beryllium products are used in the aerospace, automotive, energy, medical, and electronics industries. What eventually came to be known as chronic beryllium disease (CBD) was first identified in the 1940s, when a cluster of cases was observed in workers from the fluorescent light industry. The U.S. Atomic Energy Commission recommended the first 8-hour occupational exposure limit (OEL) for beryllium of 2.0 microg/m3 in 1949, which was later reviewed and accepted by the American Conference of Governmental Industrial Hygienists (ACGIH), the American Industrial Hygiene Association (AIHA), the American National Standards Institute (ANSI), the Occupational Safety and Health Administration (OSHA), and the vast majority of countries and standard-setting bodies worldwide. The 2.0 microg/m3 standard has been in use by the beryllium industry for more than 50 years and has been considered adequate to protect workers against clinical CBD. Recently, improved diagnostic techniques, including immunological testing and safer bronchoscopy, have enhanced our ability to identify subclinical CBD cases that would have formerly remained unidentified. Some recent epidemiological studies have suggested that some workers may develop CBD at exposures less than 2.0 microg/m3. ACGIH is currently reevaluating the adequacy of the current 2.0 microg/m3 guideline, and a plethora of research initiatives are under way to provide a better understanding of the cause of CBD. The research is focusing on the risk factors and exposure metrics that could be associated with CBD, as well as on efforts to better characterize the natural history of CBD. There is growing evidence that particle size and chemical form may be important factors that influence the risk of developing CBD. These research efforts are

  1. Beryllium metal I. experimental results on acute oral toxicity, local skin and eye effects, and genotoxicity.

    Science.gov (United States)

    Strupp, Christian

    2011-01-01

    The toxicity of soluble metal compounds is often different from that of the parent metal. Since no reliable data on acute toxicity, local effects, and mutagenicity of beryllium metal have ever been generated, beryllium metal powder was tested according to the respective Organisation for Economical Co-Operation and Development (OECD) guidelines. Acute oral toxicity of beryllium metal was investigated in rats and local effects on skin and eye in rabbits. Skin-sensitizing properties were investigated in guinea pigs (maximization method). Basic knowledge about systemic bioavailability is important for the design of genotoxicity tests on poorly soluble substances. Therefore, it was necessary to experimentally compare the capacities of beryllium chloride and beryllium metal to form ions under simulated human lung conditions. Solubility of beryllium metal in artificial lung fluid was low, while solubility in artificial lysosomal fluid was moderate. Beryllium chloride dissolution kinetics were largely different, and thus, metal extracts were used in the in vitro genotoxicity tests. Genotoxicity was investigated in vitro in a bacterial reverse mutagenicity assay, a mammalian cell gene mutation assay, a mammalian cell chromosome aberration assay, and an unscheduled DNA synthesis (UDS) assay. In addition, cell transformation was tested in a Syrian hamster embryo cell assay, and potential inhibition of DNA repair was tested by modification of the UDS assay. Beryllium metal was found not to be mutagenic or clastogenic based on the experimental in vitro results. Furthermore, treatment with beryllium metal extracts did not induce DNA repair synthesis, indicative of no DNA-damaging potential of beryllium metal. A cell-transforming potential and a tendency to inhibit DNA repair when the cell is severely damaged by an external stimulus were observed. Beryllium metal was also found not to be a skin or eye irritant, not to be a skin sensitizer, and not to have relevant acute oral

  2. Release of beryllium from mineral ores in artificial lung and skin surface fluids.

    Science.gov (United States)

    Duling, Matthew G; Stefaniak, Aleksandr B; Lawrence, Robert B; Chipera, Steve J; Virji, M Abbas

    2012-06-01

    Exposure to some manufactured beryllium compounds via skin contact or inhalation can cause sensitization. A portion of sensitized persons who inhale beryllium may develop chronic beryllium disease (CBD). Little is understood about exposures to naturally occurring beryllium minerals. The purpose of this study was to assess the bioaccessibility of beryllium from bertrandite ore. Dissolution of bertrandite from two mine pits (Monitor and Blue Chalk) was evaluated for both the dermal and inhalation exposure pathways by determining bioaccessibility in artificial sweat (pH 5.3 and pH 6.5), airway lining fluid (SUF, pH 7.3), and alveolar macrophage phagolysosomal fluid (PSF, pH 4.5). Significantly more beryllium was released from Monitor pit ore than Blue Chalk pit ore in artificial sweat buffered to pH 5.3 (0.88 ± 0.01% vs. 0.36 ± 0.00%) and pH 6.5 (0.09 ± 0.00% vs. 0.03 ± 0.01%). Rates of beryllium released from the ores in artificial sweat were faster than previously measured for manufactured forms of beryllium (e.g., beryllium oxide), known to induce sensitization in mice. In SUF, levels of beryllium were below the analytical limit of detection. In PSF, beryllium dissolution was biphasic (initial rapid diffusion followed by latter slower surface reactions). During the latter phase, dissolution half-times were 1,400 to 2,000 days, and rate constants were ~7 × 10(-10) g/(cm(2)·day), indicating that bertrandite is persistent in the lung. These data indicate that it is prudent to control skin and inhalation exposures to bertrandite dusts.

  3. Xinjiang to Build Its Largest Copper Mine

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>On September 16, the 6,000,000-ton mining project of Hudehe Copper Mine kicked off, which is the largest copper mine in Xinjiang.Jointly developed by Xinjiang Nonferrous Metals Group and Gansu Jianxin Group, Hudehe Copper Mine is located at Tuoli County, Tacheng Prefecture, Xinjiang. It is a large-scale porphyry-type copper deposit with proven copper reserve of 362,500 tons and prospective reserve of 1,000,000 tons(metal content). According to the preliminary plan, it will be built into a mine with mining and dressing capacity of 6,000,000 tons/year. With a total investment of RMB 1.466 billion, the project is expected to achieve annual sales revenue of RMB 0.8 billion and provide jobs for nearly 1,000 people.

  4. 20 CFR 30.615 - What type of tort suits filed against beryllium vendors or atomic weapons employers may...

    Science.gov (United States)

    2010-04-01

    ... beryllium vendors or atomic weapons employers may disqualify certain claimants from receiving benefits under... Special Provisions Effect of Tort Suits Against Beryllium Vendors and Atomic Weapons Employers § 30.615 What type of tort suits filed against beryllium vendors or atomic weapons employers may disqualify...

  5. 20 CFR 30.507 - What compensation will be provided to covered Part B employees who only establish beryllium...

    Science.gov (United States)

    2010-04-01

    ... Part B employees who only establish beryllium sensitivity under Part B of EEOICPA? 30.507 Section 30... Part B employees who only establish beryllium sensitivity under Part B of EEOICPA? The establishment of beryllium sensitivity does not entitle a covered Part B employee, or the eligible surviving beneficiary...

  6. 20 CFR 30.205 - What are the criteria for eligibility for benefits relating to beryllium illnesses covered under...

    Science.gov (United States)

    2010-04-01

    ... benefits relating to beryllium illnesses covered under Part B of EEOICPA? 30.205 Section 30.205 Employees... Relating to Covered Beryllium Illness Under Part B of Eeoicpa § 30.205 What are the criteria for eligibility for benefits relating to beryllium illnesses covered under Part B of EEOICPA? To...

  7. Proceedings of the third IEA international workshop on beryllium technology for fusion

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, Hiroshi; Okamoto, Makoto [eds.

    1998-01-01

    This report is the Proceedings of the Third International Energy Agency International Workshop on Beryllium Technology for Fusion. The workshop was held on October 22-24, 1997, at the Sangyou Kaikan in Mito City with 68 participants who attended from the Europe, the Russian Federation, the Kazakstan, the United States and Japan. The topics for papers were arranged into 9 sessions; beryllium applications for ITER, production and characterization, chemical compatibility and corrosion, forming and joining, plasma/tritium interactions, beryllium coating, first wall applications, neutron irradiation effects, health and safety. To utilize beryllium in the pebble type blanket, a series of discussions were intensified in multiple view points such as the swelling, He/T release from beryllium pebble irradiated up to high He content, effective thermal conductivity, tritium permeation and coating, and fabrication cost, and so on. As the plasma facing material, life time of beryllium and coated beryllium, dust and particle production, joining, waste treatment, mechanical properties and deformation by swelling were discussed as important issues. Especially, it was recognized throughout the discussions that the comparative study by the different researchers should be carried out to establish the reliability of the data reported in the workshop and in others. To enhance the comparative study, the world wide collaboration for the relative evaluation of the beryllium was proposed by the International Organization Committee and the proposal was approved by all of the participants. The 45 of the presented papers are indexed individually. (J.P.N.)

  8. DETERMINING BERYLLIUM IN DRINKING WATER BY GRAPHITE FURNACE ATOMIC ABSORPTION SPECTROSCOPY

    Science.gov (United States)

    A direct graphite furnace atomic absorption spectroscopy method for the analysis of beryllium in drinking water has been derived from a method for determining beryllium in urine. Ammonium phosphomolybdate and ascorbic acid were employed as matrix modifiers. The matrix modifiers s...

  9. Simultaneous determination of aluminium and beryllium by first-derivative synchronous solid-phase spectrofluorimetry.

    Science.gov (United States)

    Capitán, F; Manzano, E; Navalón, A; Luis Vilchez, J; Capitán-Vallvey, L F

    1992-01-01

    A method for the simultaneous determination of aluminium and beryllium in mixtures by first-deravative synchronous solid-phase spectrofluorimetry has been developed. Aluminium and beryllium reacted with morin to give fluorescent complexes, which were fixed on a dextran-type resin. The fluoresnce of the resin, packed in a 1-mm silica cell, was measured directly with a solid-surface attachment. The constant wavelength difference chosen to optimize the determination was Deltalambda = lambda(em) = 75 nm. Aluminium was measured at lambda(em)lambda = 445/520 nm and beryllium at lambda(em)lambda(em) = 430/505 nm. The range of application is between 0.5 and 5.0 ng/ml for both aluminium and beryllium. The accuracy and precision of the method are reported. The method has been successfully applied to the determination of aluminium and beryllium in synthetic mixtures and natural waters.

  10. Coolant choice for the central beryllium pipe of the BESIII beam pipe

    Science.gov (United States)

    Zheng, Li-Fang; Wang, Li; Wu, Ping; Ji, Quan; Li, Xun-Feng; Liu, Jian-Ping

    2010-07-01

    In order to take away much more heat on the BESIII beam pipe to guarantee the normal particle detection, EDM-1 (oil No.1 for electric discharge machining), with good thermal and flow properties was selected as the candidate coolant for the central beryllium pipe of the BESIII beam pipe. Its cooling character was studied and dynamic corrosion experiment was undertaken to examine its corrosion on beryllium. The experiment results show that EDM-1 would corrode the beryllium 19.9 μm in the depth in 10 years, which is weak and can be neglected. Finite element simulation and experiment research were taken to check the cooling capacity of EDM-1. The results show that EDM-1 can meet the cooling requirement of the central beryllium pipe. Now EDM-1 is being used to cool the central beryllium pipe of the BESIII beam pipe.

  11. Model study in chemisorption: atomic hydrogen on beryllium clusters

    Energy Technology Data Exchange (ETDEWEB)

    Bauschlicher, C.W. Jr.

    1976-08-01

    The interaction between atomic hydrogen and the (0001) surface of Be metal has been studied by ab initio electronic structure theory. Self-consistent-field (SCF) calculations have been performed using minimum, optimized minimum, double zeta and mixed basis sets for clusters as large as 22 Be atoms. The binding energy and equilibrium geometry (the distance to the surface) were determined for 4 sites. Both spatially restricted (the wavefunction was constrained to transform as one of the irreducible representations of the molecular point group) and unrestricted SCF calculations were performed. Using only the optimized minimum basis set, clusters containing as many as 22 beryllium atoms have been investigated. From a variety of considerations, this cluster is seen to be nearly converged within the model used, providing the most reliable results for chemisorption. The site dependence of the frequency is shown to be a geometrical effect depending on the number and angle of the bonds. The diffusion of atomic hydrogen through a perfect beryllium crystal is predicted to be energetically unfavorable. The cohesive energy, the ionization energy and the singlet-triplet separation were computed for the clusters without hydrogen. These quantities can be seen as a measure of the total amount of edge effects. The chemisorptive properties are not related to the total amount of edge effects, but rather the edge effects felt by the adsorbate bonding berylliums. This lack of correlation with the total edge effects illustrates the local nature of the bonding, further strengthening the cluster model for chemisorption. A detailed discussion of the bonding and electronic structure is included. The remaining edge effects for the Be/sub 22/ cluster are discussed.

  12. Detection of beryllium treatment of natural sapphires by NRA

    Energy Technology Data Exchange (ETDEWEB)

    Gutierrez, P.C., E-mail: carolina.gutierrez@uam.e [Centro de Micro-Analisis de Materiales (CMAM), Universidad Autonoma de Madrid, Campus de Cantoblanco, 28049 Madrid (Spain); Ynsa, M.-D.; Climent-Font, A. [Centro de Micro-Analisis de Materiales (CMAM), Universidad Autonoma de Madrid, Campus de Cantoblanco, 28049 Madrid (Spain); Dpto. Fisica Aplicada C-12, Universidad Autonoma de Madrid, Campus de Cantoblanco, 28049 Madrid (Spain); Calligaro, T. [Centre de Recherche et de Restauration des musees de France C2RMF, CNRS-UMR171, 14 quai Francois Mitterrand, 75001 Paris (France)

    2010-06-15

    Since the 1990's, artificial treatment of natural sapphires (Al{sub 2}O{sub 3} crystals coloured by impurities) by diffusion of beryllium at high temperature has become a growing practice. This process permits to enhance the colour of these gemstones, and thus to increase their value. Detection of such a treatment - diffusion of tens of {mu}g/g of beryllium in Al{sub 2}O{sub 3} crystals - is usually achieved using high sensitivity techniques like laser-ablation inductively coupled plasma mass spectrometry (LA-ICP/MS) or laser-induced breakdown spectrometry (LIBS) which are unfortunately micro-destructive (leaving 50-100-{mu}m diameter craters on the gems). The simple and non-destructive alternative method proposed in this work is based on the nuclear reaction {sup 9}Be({alpha}, n{gamma}){sup 12}C with an external helium ion beam impinging on the gem directly placed in air. The 4439 keV prompt {gamma}-ray tagging Be atoms are detected with a high efficiency bismuth germanate scintillator. Beam dose is monitored using the 2235 keV prompt {gamma}-ray produced during irradiation by the aluminium of the sapphire matrix through the {sup 27}Al({alpha}, p{gamma}){sup 30}Si nuclear reaction. The method is tested on a series of Be-treated sapphires previously analyzed by LA-ICP/MS to determine the optimal conditions to obtain a peak to background appropriate to reach the required {mu}g/g sensitivity. Using a 2.8-MeV external He beam and a beam dose of 200 {mu}C, beryllium concentrations from 5 to 16 {mu}g/g have been measured in the samples, with a detection limit of 1 {mu}g/g.

  13. Detection of beryllium treatment of natural sapphires by NRA

    Science.gov (United States)

    Gutiérrez, P. C.; Ynsa, M.-D.; Climent-Font, A.; Calligaro, T.

    2010-06-01

    Since the 1990's, artificial treatment of natural sapphires (Al 2O 3 crystals coloured by impurities) by diffusion of beryllium at high temperature has become a growing practice. This process permits to enhance the colour of these gemstones, and thus to increase their value. Detection of such a treatment - diffusion of tens of μg/g of beryllium in Al 2O 3 crystals - is usually achieved using high sensitivity techniques like laser-ablation inductively coupled plasma mass spectrometry (LA-ICP/MS) or laser-induced breakdown spectrometry (LIBS) which are unfortunately micro-destructive (leaving 50-100-μm diameter craters on the gems). The simple and non-destructive alternative method proposed in this work is based on the nuclear reaction 9Be(α, nγ) 12C with an external helium ion beam impinging on the gem directly placed in air. The 4439 keV prompt γ-ray tagging Be atoms are detected with a high efficiency bismuth germanate scintillator. Beam dose is monitored using the 2235 keV prompt γ-ray produced during irradiation by the aluminium of the sapphire matrix through the 27Al(α, pγ) 30Si nuclear reaction. The method is tested on a series of Be-treated sapphires previously analyzed by LA-ICP/MS to determine the optimal conditions to obtain a peak to background appropriate to reach the required μg/g sensitivity. Using a 2.8-MeV external He beam and a beam dose of 200 μC, beryllium concentrations from 5 to 16 μg/g have been measured in the samples, with a detection limit of 1 μg/g.

  14. Beryllium, an adjuvant that promotes gamma interferon production.

    Science.gov (United States)

    Lee, J Y; Atochina, O; King, B; Taylor, L; Elloso, M; Scott, P; Rossman, M D

    2000-07-01

    Beryllium is associated with a human pulmonary granulomatosis characterized by an accumulation of CD4(+) T cells in the lungs and a heightened specific lymphocyte proliferative response to beryllium (Be) with gamma interferon (IFN-gamma) release (i.e., a T helper 1 [Th1] response). While an animal model of Be sensitization is not currently available, Be has exhibited adjuvant effects in animals. The effects of Be on BALB/c mice immunized with soluble leishmanial antigens (SLA) were investigated to determine if Be had adjuvant activity for IFN-gamma production, an indicator of the Th1 response. In this strain of Leishmania-susceptible BALB/c mice, a Th2 response is normally observed after in vivo SLA sensitization and in vitro restimulation with SLA. If interleukin-12 (IL-12) is given during in vivo sensitization with SLA, markedly increased IFN-gamma production and decreased IL-4 production are detected. We show here that when beryllium sulfate (BeSO(4)) was added during in vivo sensitization of BALB/c mice with SLA and IL-12, significantly increased IFN-gamma production and decreased IL-4 production from lymph node and spleen cells were detected upon in vitro SLA restimulation. No specific responses were observed to Be alone. Lymph node and spleen cells from all mice proliferated strongly and comparably upon in vitro restimulation with SLA and with SLA plus Be; no differences were noted among groups of mice that received different immunization regimens. In vivo, when Be was added to SLA and IL-12 for sensitization of BALB/c mice, more effective control of Leishmania infection was achieved. This finding has implications for understanding not only the development of granulomatous reactions but also the potential for developing Be as a vaccine adjuvant.

  15. Beryllium-stimulated apoptosis in macrophage cell lines.

    Science.gov (United States)

    Sawyer, R T; Fadok, V A; Kittle, L A; Maier, L A; Newman, L S

    2000-08-21

    In vitro stimulation of bronchoalveolar lavage cells from patients with chronic beryllium disease (CBD) induces the production of TNF-alpha. We tested the hypothesis that beryllium (Be)-stimulated TNF-alpha might induce apoptosis in mouse and human macrophage cell lines. These cell lines were selected because they produce a range of Be-stimulated TNF-alpha. The mouse macrophage cell line H36.12j produces high levels of Be-stimulated TNF-alpha. The mouse macrophage cell line P388D.1 produces low, constitutive, levels of TNF-alpha and does not up-regulate Be-stimulated TNF-alpha production. The DEOHS-1 human CBD macrophage cell line does not produce constitutive or Be-stimulated TNF-alpha. Apoptosis was determined by microscopic observation of propidium iodide stained fragmented nuclei in unstimulated and BeSO(4)-stimulated macrophage cell lines. BeSO(4) induced apoptosis in all macrophage cell lines tested. Beryllium-stimulated apoptosis was dose-responsive and maximal after 24 h of exposure to 100 microM BeSO(4). In contrast, unstimulated and Al(2)(SO(4))(3)-stimulated macrophage cell lines did not undergo apoptosis. The general caspase inhibitor BD-fmk inhibited Be-stimulated macrophage cell line apoptosis at concentrations above 50 microM. Our data show that Be-stimulated macrophage cell line apoptosis was caspase-dependent and not solely dependent on Be-stimulated TNF-alpha levels. We speculate that the release of Be-antigen from apoptotic macrophages may serve to re-introduce Be material back into the lung microenvironment, make it available for uptake by new macrophages, and thereby amplify Be-stimulated cytokine production, promoting ongoing inflammation and granuloma maintenance in CBD.

  16. Physicochemical characteristics of aerosol particles generated during the milling of beryllium silicate ores: implications for risk assessment.

    Science.gov (United States)

    Stefaniak, Aleksandr B; Chipera, Steve J; Day, Gregory A; Sabey, Phil; Dickerson, Robert M; Sbarra, Deborah C; Duling, Mathew G; Lawrence, Robert B; Stanton, Marcia L; Scripsick, Ronald C

    2008-01-01

    Inhalation of beryllium dusts generated during milling of ores and cutting of beryl-containing gemstones is associated with development of beryllium sensitization and low prevalence of chronic beryllium disease (CBD). Inhalation of beryllium aerosols generated during primary beryllium production and machining of the metal, alloys, and ceramics are associated with sensitization and high rates of CBD, despite similar airborne beryllium mass concentrations among these industries. Understanding the physicochemical properties of exposure aerosols may help to understand the differential immunopathologic mechanisms of sensitization and CBD and lead to more biologically relevant exposure standards. Properties of aerosols generated during the industrial milling of bertrandite and beryl ores were evaluated. Airborne beryllium mass concentrations among work areas ranged from 0.001 microg/m(3) (beryl ore grinding) to 2.1 microg/m(3) (beryl ore crushing). Respirable mass fractions of airborne beryllium-containing particles were 80% in high-energy input areas (beryl melting, beryl grinding). Particle specific surface area decreased with processing from feedstock ores to drumming final product beryllium hydroxide. Among work areas, beryllium was identified in three crystalline forms: beryl, poorly crystalline beryllium oxide, and beryllium hydroxide. In comparison to aerosols generated by high-CBD risk primary production processes, aerosol particles encountered during milling had similar mass concentrations, generally lower number concentrations and surface area, and contained no identifiable highly crystalline beryllium oxide. One possible explanation for the apparent low prevalence of CBD among workers exposed to beryllium mineral dusts may be that characteristics of the exposure material do not contribute to the development of lung burdens sufficient for progression from sensitization to CBD. In comparison to high-CBD risk exposures where the chemical nature of aerosol

  17. Cryogenic optical tests of a lightweight HIP beryllium mirror

    Science.gov (United States)

    Melugin, Ramsey K.; Miller, Jacob H.; Young, J. A.; Howard, Steven D.; Pryor, G. Mark

    Five interferometric tests were conducted at cryogenic temperatures on a lightweight, 50 cm diameter, hot isostatic pressed (HIP) beryllium mirror in the Ames Research Center (ARC) Cryogenic Optics Test Facility. The purpose of the tests was to determine the stability of the mirror's figure when cooled to cryogenic temperatures. Test temperatures ranged from room ambient to 8 K. One cycle to 8 K and five cycles to 80 K were performed. Optical and thermal test methods are described. Data is presented to show the amount of cryogenic distortion and hysteresis present in the mirror when measured with an earlier, Shack interferometer, and with a newly-acquired, phase-measuring interferometer.

  18. Microstructure and mechanical properties of neutron irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Ishitsuka, E.; Kawamura, H. [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment; Terai, T.; Tanaka, S.

    1998-01-01

    Microstructure and mechanical properties of the neutron irradiated beryllium with total fast neutron fluences of 1.3 - 4.3 x 10{sup 21} n/cm{sup 2} (E>1 MeV) at 327 - 616degC were studied. Swelling increased by high irradiation temperature, high fluence, and by the small grain size and high impurity. Obvious decreasing of the fracture stress was observed in the bending test and in small grain specimens which had many helium bubbles on the grain boundary. Decreasing of the fracture stress for small grain specimens was presumably caused by crack propagation on the grain boundaries which weekend by helium bubbles. (author)

  19. Inorganic arrangement crystal beryllium, lithium, selenium and silicon

    CERN Document Server

    Gobato, Ricardo; Fedrigo, Desire Francine Gobato

    2015-01-01

    The use of inorganic crystals technology has been widely date. Since quartz crystals for watches in the nineteenth century, and common way radio in the early twentieth century, to computer chips with new semiconductor materials. Chemical elements such as beryllium, lithium, selenium and silicon, are widely used in technology. The development of new crystals arising from that arrangement can bring technological advances in several areas of knowledge. The likely difficulty of finding such crystals in nature or synthesized, suggest an advanced study of the subject. A study using computer programs with ab initio method was applied. As a result of the likely molecular structure of the arrangement of a crystal was obtained.

  20. Atomic, Crystal, Elastic, Thermal, Nuclear, and Other Properties of Beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, A

    2006-02-01

    This report is part of a series of documents that provide a background to those involved in the construction of beryllium components and their applications. This report is divided into five sub-sections: Atomic/Crystal Structure, Elastic Properties, Thermal Properties, Nuclear Properties, and Miscellaneous Properties. In searching through different sources for the various properties to be included in this report, inconsistencies were at times observed between these sources. In such cases, the values reported by the Handbook of Chemistry and Physics was usually used. In equations, except where indicated otherwise, temperature (T) is in degrees Kelvin.

  1. Tritium analyses of COBRA-1A2 beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Baldwin, D.L. [Pacific Northwest National Lab., Richland, WA (United States)

    1998-03-01

    Selected tritium measurements have been completed for the COBRA-1A2 experiment C03 and D03 beryllium pebbles. The completed results, shown in Tables 1, 2, and 3, include the tritium assay results for the 1-mm and 3-mm C03 pebbles, and the 1-mm D03 pebbles, stepped anneal test results for both types of 1-mm pebbles, and the residual analyses for the stepped-anneal specimens. All results have been reported with date-of-count and are not corrected for decay. Stepped-anneal tritium release response is provided in addenda.

  2. Use of notched beams to establish fracture criteria for beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Mayville, R.A.

    1980-01-04

    The fracture of an improved form of pure beryllium was studied under triaxial tensile stresses. This state of stress was produced by testing notched beams, which were thick enough to be in a state of plane strain at the center. A plane strain, elastic-incremental plasticity finite element program was then used to determine the stress and strain distributions at fracture. A four-point bend fixture was used to load the specimens. It was carefully designed and manufactured to eliminate virtually all of the shear stresses at the reduced section of the notched beams. The unixial properties were obtained.

  3. Beryllium ignition target design for indirect drive NIF experiments

    Science.gov (United States)

    Simakov, A. N.; Wilson, D. C.; Yi, S. A.; Kline, J. L.; Salmonson, J. D.; Clark, D. S.; Milovich, J. L.; Marinak, M. M.

    2016-03-01

    Beryllium (Be) ablator offers multiple advantages over carbon based ablators for indirectly driven NIF ICF ignition targets. These are higher mass ablation rate, ablation pressure and ablation velocity, lower capsule albedo, and higher thermal conductivity at cryogenic temperatures. Such advantages can be used to improve the target robustness and performance. While previous NIF Be target designs exist, they were obtained a long time ago and do not incorporate the latest improved physical understanding and models based upon NIF experiments. Herein, we propose a new NIF Be ignition target design at 1.45 MJ, 430 TW that takes all this knowledge into account.

  4. Status of the Development of Beryllium-Copper Alloy Ignition Capsules by Precision Machining

    Science.gov (United States)

    Nobile, Arthur

    2005-10-01

    Cu-doped Be capsules are being developed for ignition on the National Ignition Facility (NIF). The fabrication approach being pursued at Los Alamos is based on bonding of cylindrical parts containing precision machined hemispherical cavities, followed by machining the external contour to produce a spherical capsule. While we have demonstrated this approach, there are several key issues that need to be resolved before a capsule meeting NIF specifications can be produced. These issues are synthesis of high purity small grain size Be-Cu alloy, formation of a hemishell bond strong enough to allow the capsule to be machined after the hemishells are bonded, precision machining and polishing of the capsule to meet stringent specifications for surface finish and spherical quality, and filling with DT. In this paper we report on the progress that has been made on these issues. This work is performed at Los Alamos National Laboratory and supported by U.S. Department of Energy under contract number W7405-ENG36

  5. Machining characteristics and fracture morphologies in a copper-beryllium (Cu-2Be) alloy

    Science.gov (United States)

    Sudhakar, K. V.; Cisneros, J. C.; Cervantes, Hector; Pineda, Cosme Gomez

    2006-02-01

    The technology of materials removal is improved greatly by the introduction of advanced cutting tools like cubic boron nitride, ceramics, polycrystalline diamond and the more recent whisker-reinforced materials. In this paper, the influence of cutting temperature on machinability, mechanical properties, microstructure, and fracture morphology of Cu-2Be alloy using a polycrystalline diamond cutter is investigated. The information on machining, microstructure, and fracture morphology of Cu-2Be alloy are very useful to understand their fabrication characteristics and the basic mechanisms of its deformation and fracture. The machinability (in terms of surface finish) of Cu-2Be alloy is evaluated as a function of cutting temperature, resulting from wet and dry cutting. Machining is carried out on a Hardinge Cobra 42 CNC machine (Hardinge Inc., Elmira, NY), and the machining parameters used—cutting speed, depth of cut, and feed rate—are kept constant during both wet and dry cutting. The machined surface finish on Cu-2Be alloy is measured using a surface finish analyzer (Surftest 401, series 178) technique. The machined specimens are examined for their strength and hardness properties using a standard Universal Testing Machine and Rockwell hardness tester, respectively. Wet cutting (using coolants) produced a smooth surface finish when compared with dry cutting of the Cu-2Be alloy. The machined specimens are examined for their microstructural features using a Nikon optical microscope. The specimens are etched using a suitable etchant solution for revealing such microstructure constituents as grain size, phase proportions, and the possible overheated areas (especially in dry cutting). The fractured surfaces from the tensile and impact toughness tests are investigated for their fracture morphologies (dry and wet cutting) using a microprocessor-controlled scanning electron microscope (Jeol Model JSM 5910 LV). A detailed analysis is also made to understand and interpret the basic fracture mechanisms responsible for crack initiation and crack propagation. The Cu-2Be alloy showed relatively higher mechanical properties in wet cutting in comparison to dry cutting operations. Fracture studies demonstrated intergranular and ductile fractures as dominant modes of fracture mechanisms in Cu-2Be alloy.

  6. SOURCE AND PATHWAY DETERMINATION FOR BERYLLIUM FOUND IN BECHTEL NEVADA NORTH LAS VEGAS FACILITIES

    Energy Technology Data Exchange (ETDEWEB)

    BECHTEL NEVADA

    2004-07-01

    In response to the report ''Investigation of Beryllium Exposure Cases Discovered at the North Las Vegas Facility of the National Nuclear Security Administration'', published by the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA) in August 2003, Bechtel Nevada (BN) President and General Manager Dr. F. A. Tarantino appointed the Beryllium Investigation & Assessment Team (BIAT) to identify both the source and pathway for the beryllium found in the North Las Vegas (NLV) B-Complex. From September 8 to December 18, 2003, the BIAT investigated the pathway for beryllium and determined that a number of locations existed at the Nevada Test Site (NTS) which could have contained sufficient quantities of beryllium to result in contamination if transported. Operations performed in the B-1 Building as a result of characterization activities at the Engine Maintenance, Assembly, and Disassembly (EMAD); Reactor Maintenance, Assembly, and Disassembly (RMAD); Test Cells A and C; and the Central Support Facility in Area 25 had the greatest opportunity for transport of beryllium. Investigative monitoring and sampling was performed at these sites with subsequent transport of sample materials, equipment, and personnel from the NTS to the B-1 Building. The timeline established by the BIAT for potential transport of the beryllium contamination into the B-1 Building was from September 1997 through November 2002. Based on results of recently completed swipe sampling, no evidence of transport of beryllium from test areas has been confirmed. Results less than the DOE beryllium action level of 0.2 ???g/100 cm2 were noted for work support facilities located in Area 25. All of the identified sites in Area 25 worked within the B-1 tenant's residency timeline have been remediated. Legacy contaminants have either been disposed of or capped with clean borrow material. As such, no current opportunity exists for release or spread of beryllium

  7. The mechanism for production of beryllium fluoride from the product of ammonium fluoride processing of beryllium- containing raw material

    Science.gov (United States)

    Kraydenko, R. I.; Dyachenko, A. N.; Malyutin, L. N.; Petlin, I. V.

    2016-06-01

    The technique of fluorite-phenacite-bertrandite ores from Russian Ermakovskoe deposit processing by ammonium bifluoride is described. To determine the temperature mode and the thermal dissociation mechanism of ammonium tetrafluoroberyllate (the product of ammonium-fluoride leaching of the ore) the TG/DTA have been carried out. By IR spectroscopy and XRD the semi-products of ammonium tetrafluoroberyllate thermal dissociation have been identified. The hygroscopic low-temperature beryllium fluoride forms higher than 380°C. The less hydroscopic form of BeF2 have been produced at 600°C.

  8. Influence of neutron irradiation on the tritium retention in beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Rolli, R.; Ruebel, S.; Werle, H. [Forschungszentrum Karlsruhe, Inst. fuer Neutronenphysik und Reaktortechnik, Karlsruhe (Germany); Wu, C.H.

    1998-01-01

    Carbon-based materials and beryllium are the candidates for protective layers on the components of fusion reactors facing plasma. In contact with D-T plasma, these materials absorb tritium, and it is anticipated that tritium retention increases with the neutron damage due to neutron-induced traps. Because of the poor data base for beryllium, the work was concentrated on it. Tritium was loaded into the samples from stagnant T{sub 2}/H{sub 2} atmosphere, and afterwards, the quantity of the loaded tritium was determined by purged thermal annealing. The specification of the samples is shown. The samples were analyzed by SEM before and after irradiation. The loading and the annealing equipments are contained in two different glove boxes with N{sub 2} inert atmosphere. The methods of loading and annealing are explained. The separation of neutron-produced and loaded tritium and the determination of loaded tritium in irradiated samples are reported. Also the determination of loaded tritium in unirradiated samples is reported. It is evident that irradiated samples contained much more loaded tritium than unirradiated samples. The main results of this investigation are summarized in the table. (K.I.)

  9. Calculations for electron-impact excitation and ionization of beryllium

    CERN Document Server

    Zatsarinny, Oleg; Fursa, Dmitry V; Bray, Igor

    2016-01-01

    The B-spline R-matrix and the convergent close-coupling methods are used to study electron collisions with neutral beryllium over an energy range from threshold to 100 eV. Coupling to the target continuum significantly affects the results for transitions from the ground state, but to a lesser extent the strong transitions between excited states. Cross sections are presented for selected transitions between low-lying physical bound states of beryllium, as well as for elastic scattering, momentum transfer, and ionization. The present cross sections for transitions from the ground state from the two methods are in excellent agreement with each other, and also with other available results based on nonperturbative convergent pseudo-state and time-dependent close-coupling models. The elastic cross section at low energies is dominated by a prominent shape resonance. The ionization from the $(2s2p)^3P$ and $(2s2p)^1P$ states strongly depends on the respective term. The current predictions represent an extensive set o...

  10. Review and interpretation of recent cosmic ray beryllium isotope measurements

    Energy Technology Data Exchange (ETDEWEB)

    Buffington, A.

    1978-04-26

    Be/sup 10/ has long been of interest for cosmic ray propagation, because its radioactive decay half-life is well matched to the expected cosmic ray age. Recent beryllium isotope measurements from satellites and balloons have covered an energy range from about 30 to 300 MeV/nucleon/sup 1-3/. At the lowest energies, most of the Be/sup 10/ is absent, indicating a cosmic ray lifetime of order 2 x 10/sup 7/ years and the rather low average density of 0.2 atoms/cc traversed by the cosmic rays. At higher energies, a greater proportion of Be/sup 10/ is observed, indicating a somewhat shorter lifetime. These experiments will be reviewed and then compared with a new experiment covering from 100 to 1000 Mev/nucleon/sup 4/. Although improved experiments will be necessary to realize the full potential of cosmic ray beryllium isotope measurements, these first results are already disclosing interesting and unexpected facts about cosmic ray acceleration and propagation.

  11. Microstructural Characterization of Beryllium Treated Al-Si Alloys

    Directory of Open Access Journals (Sweden)

    M. F. Ibrahim

    2015-01-01

    Full Text Available The present study was carried out on B356 and B357 alloys using the thermal analysis technique. Metallographic samples prepared from these castings were examined using optical microscopy and FESEM. Results revealed that beryllium causes partial modification of the eutectic Si, similar to that reported for magnesium additions. Addition of 0.8 wt.% Mg reduces the eutectic temperature by ~10°C. During solidification of alloys containing high levels of Fe and Mg, but no Sr, formation of a Be-Fe phase was detected at 611°C, close to that of α-Al. The Be-Fe phase precipitates in script-like form at or close to the β-Al5SiFe platelets. A new reaction, composed of fine particles of Si and π-Fe phase, was observed to occur near the end of solidification in high Mg-, high Fe-, and Be-containing alloys. The amount of this reaction decreased with the addition of Sr. Occasionally, Be-containing phase particles were observed as part of the reaction. Addition of Be has a noticeable effect on decreasing the β-Al5FeSi platelet length; this effect may be enhanced by addition of Sr. Beryllium addition also results in precipitation of the β-Al5FeSi phase in nodular form, which lowers its harmful effects on the alloy mechanical properties.

  12. Remarkable Hydrogen Storage on Beryllium Oxide Clusters: First Principles Calculations

    CERN Document Server

    Shinde, Ravindra

    2016-01-01

    Since the current transportation sector is the largest consumer of oil, and subsequently responsible for major air pollutants, it is inevitable to use alternative renewable sources of energies for vehicular applications. The hydrogen energy seems to be a promising candidate. To explore the possibility of achieving a solid-state high-capacity storage of hydrogen for onboard applications, we have performed first principles density functional theoretical calculations of hydrogen storage properties of beryllium oxide clusters (BeO)$_{n}$ (n=2 -- 8). We observed that polar BeO bond is responsible for H$_{2}$ adsorption. The problem of cohesion of beryllium atoms does not arise, as they are an integral part of BeO clusters. The (BeO)$_{n}$ (n=2 -- 8) adsorbs 8--12 H$_{2}$ molecules with an adsorption energy in the desirable range of reversible hydrogen storage. The gravimetric density of H$_{2}$ adsorbed on BeO clusters meets the ultimate 7.5 wt% limit, recommended for onboard practical applications. In conclusion,...

  13. Joint ventures

    DEFF Research Database (Denmark)

    Sørensen, Karsten Engsig

    Afhandlingen analysere de konkurrenceretlige og selskabsretlige regler som er bestemmende for hvordan et joint venture samarbejde er struktureret......Afhandlingen analysere de konkurrenceretlige og selskabsretlige regler som er bestemmende for hvordan et joint venture samarbejde er struktureret...

  14. Joint swelling

    Science.gov (United States)

    ... chap 275. Raftery AT, Lim E, Ostor AJK. Joint disorders. In: Raftery AT, Lim E, Ostor AJK, eds. ... A.M. Editorial team. Related MedlinePlus Health Topics Joint Disorders Browse the Encyclopedia A.D.A.M., Inc. ...

  15. New and Emerging Technologies for Real-Time Air and Surface Beryllium Monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Phifer, B.E. Jr.; Churnetski, E.L.; Cooke, L.E.; Reed, J.J.; Howell, M.L.; Smith, V.D.

    2001-09-01

    In this study, five emerging technologies were identified for real-time monitoring of airborne beryllium: Microwave-Induced Plasma Spectroscopy (MIPS), Aerosol Beam-Focused Laser-Induced Plasma Spectroscopy (ABFLIPS), Laser-Induced Breakdown Spectroscopy (LIBS), Surfaced-Enhanced Raman Scattering (SERS) Spectroscopy, and Micro-Calorimetric Spectroscopy (CalSpec). Desired features of real-time air beryllium monitoring instrumentation were developed from the Y-12 CBDPP. These features were used as guidelines for the identification of potential technologies as well as their unique demonstrated capability to provide real-time monitoring of similar materials. However, best available technologies were considered, regardless of their ability to comply with the desired features. None of the five technologies have the capability to measure the particle size of airborne beryllium. Although reducing the total concentration of airborne beryllium is important, current literature suggests that reducing or eliminating the concentration of respirable beryllium is critical for worker health protection. Eight emerging technologies were identified for surface monitoring of beryllium. CalSpec, MIPS, SERS, LIBS, Laser Ablation, Absorptive Stripping Voltametry (ASV), Modified Inductively Coupled Plasma (ICP) Spectroscopy, and Gamma BeAST. Desired features of real-time surface beryllium monitoring were developed from the Y-12 CBDPP. These features were used as guidelines for the identification of potential technologies. However, the best available technologies were considered regardless of their ability to comply with the desired features.

  16. Development of radiation resistant grades of beryllium for nuclear and fusion facilities

    Energy Technology Data Exchange (ETDEWEB)

    Kupriyanov, I.B.; Gorokhov, V.A.; Nikolaev, G.N. [Russia Research Institute of Inorganic Materials, Moscow (Russian Federation)

    1995-09-01

    R&D results on beryllium with high radiation resistance obtained recently are described in this report. The data are presented on nine different grades of isotropic beryllium manufactured by VNIINM and distinguished by both initial powder characteristics and properties of billets, made of these powders. The average grain size of the investigated beryllium grades varied from 8 to 26 {mu}m, the content of beryllium oxide was 0.9 - 3.9 wt.%, the dispersity of beryllium oxide - 0.04 - 0.5 {mu}m, tensile strength -- 250 - 650 MPa. All materials were irradiated in SM - 2 reactor over the temperature range 550 - 780{degrees}C. The results of the investigation showed, that HIP beryllium grades are less susceptible to swelling at higher temperatures in comparison with hot pressed and extruded grades. Beryllium samples, having the smallest grain size, demonstrated minimal swelling, which was less than 0.8 % at 750{degrees}C and Fs = 3.7 {center_dot}10{sup 21} cm{sup -2} (E>0.1 MeV). The mechanical properties, creep and microstructure parameters, measured before and after irradiation, are presented.

  17. Sampling and analysis plan for assessment of beryllium in soils surrounding TA-40 building 15

    Energy Technology Data Exchange (ETDEWEB)

    Ruedig, Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-12-19

    Technical Area (TA) 40 Building 15 (40-15) is an active firing site at Los Alamos National Laboratory. The weapons facility operations (WFO) group plans to build an enclosure over the site in 2017, so that test shots may be conducted year-round. The enclosure project is described in PRID 16P-0209. 40-15 is listed on LANL OSH-ISH’s beryllium inventory, which reflects the potential for beryllium in/on soils and building surfaces at 40-15. Some areas in and around 40-15 have previously been sampled for beryllium, but past sampling efforts did not achieve complete spatial coverage of the area. This Sampling and Analysis Plan (SAP) investigates the area surrounding 40-15 via 9 deep (≥1-ft.) soil samples and 11 shallow (6-in.) soil samples. These samples will fill the spatial data gaps for beryllium at 40-15, and will be used to support OSH-ISH’s final determination of 40-15’s beryllium registry status. This SAP has been prepared by the Environmental Health Physics program in consultation with the Industrial Hygiene program. Industrial Hygiene is the owner of LANL’s beryllium program, and will make a final determination with regard to the regulatory status of beryllium at 40-15.

  18. Use of 41Ar production to measure ablator areal density in NIF beryllium implosions

    Science.gov (United States)

    Wilson, D. C.; Cassata, W. B.; Sepke, S. M.; Velsko, C. A.; Huang, H.; Yeamans, C. B.; Kline, J. L.; Yi, A.; Simakov, A. N.; Haan, S. W.; Batha, S. H.; Dewald, E. L.; Rygg, J. R.; Tommasini, R.; Xu, H.; Kong, C.; Bae, J.; Rice, N.

    2017-02-01

    For the first time, 41Ar produced by the (n,ϒ) reaction from 40Ar in the beryllium shell of a DT filled Inertial Confinement Fusion capsule has been measured. Ar is co-deposited with beryllium in the sputter deposition of the capsule shell. Combined with a measurement of the neutron yield, the radioactive 41Ar then quantifies the areal density of beryllium during the DT neutron production. The measured 1.15 ± 0.17 × 10+8 atoms of 41Ar are 2.5 times that from the best post-shot calculation, suggesting that the Ar and Be areal densities are correspondingly higher than those calculated. Possible explanations are that (1) the beryllium shell is compressed more than calculated, (2) beryllium has mixed into the cold DT ice, or more likely (3) less beryllium is ablated than calculated. Since only one DT filled beryllium capsule has been fielded at NIF, these results can be confirmed and expanded in the future.

  19. On use of beryllium in fusion reactors: Resources, impurities and necessity of detritiation after irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Kolbasov, B.N., E-mail: b.kolbasov@yandex.ru; Khripunov, V.I., E-mail: Khripunov_VI@nrcki.ru; Biryukov, A.Yu.

    2016-11-01

    Highlights: • Potential needs in Be for fusion power engineering may exceed Be resources. • Be recycling after its operation in a fusion power plant (FPP) seems inevitable. • U impurity in Be seriously impairs environmental properties of fusion power plants. • Upon burial of irradiated Be the main problems are caused by U and {sup 3}H impurities. • Clearance of Be extracted from a FPP is impossible due to U impurity. - Abstract: Worldwide identified resources of beryllium somewhat exceed 80 000 t. Beryllium production in all the countries of the world in 2012 was about 230 t. At the same time, some conceptual designs of fusion power reactors envisage utilization of several hundred tons of this metal. Therefore return of beryllium into the production cycle (recycling) will be necessary. The beryllium ore from some main deposits has uranium content inadmissible for fusion reactors. This fact raises a question on the need to develop and apply an economically acceptable technology for beryllium purification from the uranium. Practically any technological procedure with beryllium used in fusion reactors requires its detritiation. A study of tritium and helium release from irradiated beryllium at different temperatures and rates of temperature increase was performed at Kurchatov Institute.

  20. Target organ localization of memory CD4(+) T cells in patients with chronic beryllium disease.

    Science.gov (United States)

    Fontenot, Andrew P; Canavera, Scott J; Gharavi, Laia; Newman, Lee S; Kotzin, Brian L

    2002-11-01

    Chronic beryllium disease (CBD) is caused by exposure to beryllium in the workplace, and it remains an important public health concern. Evidence suggests that CD4(+) T cells play a critical role in the development of this disease. Using intracellular cytokine staining, we found that the frequency of beryllium-specific CD4(+) T cells in the lungs (bronchoalveolar lavage) of 12 CBD patients ranged from 1.4% to 29% (mean 17.8%), and these T cells expressed a Th1-type phenotype in response to beryllium sulfate (BeSO(4)). Few, if any, beryllium-specific CD8(+) T cells were identified. In contrast, the frequency of beryllium-responsive CD4(+) T cells in the blood of these subjects ranged from undetectable to 1 in 500. No correlation was observed between the frequency of beryllium-responsive bronchoalveolar lavage (BAL) CD4(+) T cells as detected by intracellular staining and lymphocyte proliferation in culture after BeSO(4) exposure. Staining for surface marker expression showed that nearly all BAL T cells exhibit an effector memory cell phenotype. These results demonstrate a dramatically high frequency and compartmentalization of antigen-specific effector memory CD4(+) cells in the lungs of CBD patients. These studies provide insight into the phenotypic and functional characteristics of antigen-specific T cells invading other inaccessible target organs in human disease.

  1. Machining risk of beryllium disease and sensitization with median exposures below 2 micrograms/m3.

    Science.gov (United States)

    Kreiss, K; Mroz, M M; Newman, L S; Martyny, J; Zhen, B

    1996-07-01

    We examined the prevalence of beryllium sensitization in relation to work process and beryllium exposure measurements in a beryllia ceramics plant that had operated since 1980. We interviewed 136 employees (97.8% of the workforce), ascertained beryllium sensitization with the beryllium lymphocyte proliferation blood test, and reviewed historical industrial hygiene measurements. Of eight beryllium-sensitized employees (5.9%), six (4.4% of participating employees) had granulomatous disease on transbronchial lung biopsy. Machinists had a sensitization rate of 14.3% compared to a rate of 1.2% among other employees. Machining had significantly higher general area and breathing zone measurements than did other processes in the time period in which most beryllium-sensitized cases had started machining work. Daily weighted average (DWA) estimates of exposure for matching processes also exceeded estimates for other work processes in that time period, with a median DWA of 0.9 microgram/m3. Machining process DWAs accounted for the majority of DWAs exceeding the 2.0 micrograms/m3 OSHA standard, with 8.1% of machining DWAs above the standard. We conclude that lowering machining process-related exposures may be important to lowering risk of beryllium disease.

  2. Joint ventures

    NARCIS (Netherlands)

    M.N. Hoogendoorn (Martin)

    2009-01-01

    textabstractEen veel voorkomende wijze van samenwerking tussen ondernemingen is het uitvoeren van activiteiten in de vorm van een joint venture. Een joint venture is bijna altijd een afzonderlijke juridische entiteit. De partners in de joint venture voeren gezamenlijk de zeggenschap uit. In internat

  3. Joint ventures

    NARCIS (Netherlands)

    M.N. Hoogendoorn (Martin)

    2009-01-01

    textabstractEen veel voorkomende wijze van samenwerking tussen ondernemingen is het uitvoeren van activiteiten in de vorm van een joint venture. Een joint venture is bijna altijd een afzonderlijke juridische entiteit. De partners in de joint venture voeren gezamenlijk de zeggenschap uit. In internat

  4. Considerations for the development of health-based surface dust cleanup criteria for beryllium.

    Science.gov (United States)

    Shay, Erin; De Gandiaga, Elise; Madl, Amy K

    2013-03-01

    The exposure-response patterns with beryllium sensitization (BeS), chronic beryllium disease (CBD) and lung cancer are influenced by a number of biological and physicochemical factors. Recent studies have suggested dermal exposure as a pathway for BeS. In light of the current non-health-based DOE Beryllium Rule surface criteria, the feasibility of deriving a human health-based surface dust cleanup criteria (SDCC) for beryllium was assessed based on toxicology and health risk factors via all potential routes of exposure. Beryllium-specific and general exposure factors were evaluated, including (1) beryllium physicochemical characteristics, bioavailability and influence on disease prevalence, and (2) chemical dissipation, resuspension and transfer. SDCC for non-cancer (SDCC) and cancer (SDCC) endpoints were derived from a combination of modern methods applied for occupational, residential and building reentry surface dust criteria. The most conservative SDCC estimates were derived for dermal exposure (5-379 μg/100 cm for 0.1-1% damaged skin and 17-3337 μg/100 cm for intact skin), whereas the SDCC for inhalation exposure ranged from 51 to 485 μg/100 cm. Considering this analysis, the lowest DOE surface criterion of 0.2 μg/100 cm is conservative for minimizing exposure and potential risks associated with beryllium-contaminated surfaces released for non-beryllium industrial or public sector use. Although methodological challenges exist with sampling and analysis procedures, data variability and interpretation of surface dust information in relation to anthropogenic and natural background concentrations, this evaluation should provide useful guidance with regard to cleanup of manufacturing equipment or remediation of property for transfer to the general public or non-beryllium industrial facilities.

  5. The structure and the Raman vibrational spectrum of the beryllium aquacation.

    Science.gov (United States)

    Rozmanov, Dmitry A; Sizova, Olga V; Skripkin, Mikhail Yu; Burkov, Kim A

    2005-11-01

    The experimental Raman vibrational spectrum of the 5.94 m water solution of the beryllium(II) chloride has been acquired. Theoretical frequencies, infrared and Raman intensities of the vibrational spectrum of the beryllium cation tetrahydrate have been calculated by means of quantum chemical approach. The peaks of the experimental spectrum have been assigned on the basis of the results of the quantum-chemical calculations. It has been shown that the hydrating surrounding of the aquacation increases effectively the frequency of the beryllium-oxygen stretching vibration by 16% in comparison with the free complex.

  6. Mathematical simulation of pressing X-ray lenses from nanocrystalline beryllium

    Science.gov (United States)

    Mishin, V. V.; Shishov, I. A.; Glukhov, P. A.; Zabrodin, A. V.; Semenov, A. A.; Brylev, D. A.; Anikin, A. S.

    2016-10-01

    A computer model is developed to describe the pressing of a beryllium lens using the Deform software package. This model takes into account the rheological properties of beryllium and the deforming tool. The state of stress of a workpiece is determined at various stages of pressing, and the probability of fracture of nanocrystalline beryllium is estimated using the normalized Cockcroft-Latham criterion. The temperature dependence of the limiting values of the fracture criterion is found and used to choose the pressing conditions that exclude fracture of lenses.

  7. Study of beryllium redeposition under bombardment by high intensity -low energy- hydrogen ion beams

    Energy Technology Data Exchange (ETDEWEB)

    Gureev, V.M.; Guseva, M.I.; Danelyan, L.S. [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation)] [and others

    1998-01-01

    The results of studying the erosion of beryllium under an effect of intense ion fluxes with the energy of 250 eV, at the fluences {approx}10{sup 2}1 cm{sup -2}, at the MAGRAS-stand are given. The operating conditions under which a practically-complete redeposition of the sputtered beryllium upon the target surface were experimentally-realized. A change in the microstructure of a beryllium target under sputtering and redeposition is analyzed. Some technological applications are considered. (author)

  8. Conditions for preparation of ultrapure beryllium by electrolytic refining in molten alkali-metal chlorides

    Energy Technology Data Exchange (ETDEWEB)

    Wohlfarth, Hagen

    1982-02-01

    Electrolytic refining is regarded as the most suitable process for the production of beryllium with impurity contents below 1 at.-ppM. Several parameters are important for electrolytic refining of beryllium in a BeCl/sub 2/-containing LiCl-KCl melt: current density, BeCl/sub 2/ content, electrolyte temperature, composition of the unpurified beryllium and impurity-ion concentrations in the melt, as well as apparatus characteristics such as rotation speed of the cathode and condition of the crucible material. These factors were studied and optimized such that extensive removal of the maximum number of accompanying and alloying elements was achieved.

  9. Beryllium Exposure Control Program at the Cardiff Atomic Weapons Establishment in the United Kingdom.

    Science.gov (United States)

    Johnson, J S; Foote, K; McClean, M; Cogbill, G

    2001-05-01

    The Cardiff Atomic Weapons Establishment (AWE) plant, located in Cardiff, Wales, United Kingdom, used metallic beryllium in their beryllium facility during the years of operation 1961-1997. The beryllium production processes included melting and casting, powder production, pressing, machining, and heat and surface treatments. As part of Cardiff's industrial hygiene program, extensive area measurements and personal lapel measurements of airborne beryllium concentrations were collected for Cardiff workers over the 36-year period of operation. In addition to extensive air monitoring, the beryllium control program also utilized surface contamination controls, building design, engineering controls, worker controls, material controls, and medical surveillance. The electronic database includes 367,757 area sampling records at 101 locations and 217,681 personal lapel sampling records collected from 194 employees over the period 1981-1997. Similar workplace samples were collected from 1961 to 1980, but they were not analyzed because they were not available electronically. Annual personal mean sampling concentrations for all workers ranged from 0.11 to 0.72 micrograms per cubic meter (microg/m3) with 95th percentiles ranging from 0.22 to 1.89 microg/m3; foundry workers worked in the highest concentration areas with a mean of 0.87 microg/m3 and a 95th percentile of 2.9 microg/m3. Area sampling concentrations, as expected, were lower than personal sampling concentrations. Mean annual area sample concentrations for all locations ranged from 0.02 to 0.32 microg/m3. The area sample 95th percentile concentrations for all years were below 0.5 microg/m3. For the overwhelming majority of samples, airborne beryllium concentrations were below the 2.0 microg/m3 standard. Although blood lymphocyte testing for beryllium sensitization has not been routinely conducted among these workers, this metal beryllium processing facility is the only large scale beryllium facility of its kind to have

  10. Photoluminescence enhancement from GaN by beryllium doping

    Science.gov (United States)

    García-Gutiérrez, R.; Ramos-Carrazco, A.; Berman-Mendoza, D.; Hirata, G. A.; Contreras, O. E.; Barboza-Flores, M.

    2016-10-01

    High quality Be-doped (Be = 0.19 at.%) GaN powder has been grown by reacting high purity Ga diluted alloys (Be-Ga) with ultra high purity ammonia in a horizontal quartz tube reactor at 1200 °C. An initial low-temperature treatment to dissolve ammonia into the Ga melt produced GaN powders with 100% reaction efficiency. Doping was achieved by dissolving beryllium into the gallium metal. The powders synthesized by this method regularly consist of two particle size distributions: large hollow columns with lengths between 5 and 10 μm and small platelets in a range of diameters among 1 and 3 μm. The GaN:Be powders present a high quality polycrystalline profile with preferential growth on the [10 1 bar 1] plane, observed by means of X-ray diffraction. The three characteristics growth planes of the GaN crystalline phase were found by using high resolution TEM microscopy. The optical enhancing of the emission in the GaN powder is attributed to defects created with the beryllium doping. The room temperature photoluminescence emission spectra of GaN:Be powders, revealed the presence of beryllium on a shoulder peak at 3.39 eV and an unusual Y6 emission at 3.32eV related to surface donor-acceptor pairs. Also, a donor-acceptor-pair transition at 3.17 eV and a phonon replica transition at 3.1 eV were observed at low temperature (10 K). The well-known yellow luminescence band coming from defects was observed in both spectra at room and low temperature. Cathodoluminescence emission from GaN:Be powders presents two main peaks associated with an ultraviolet band emission and the yellow emission known from defects. To study the trapping levels related with the defects formed in the GaN:Be, thermoluminescence glow curves were obtained using UV and β radiation in the range of 50 and 150 °C.

  11. Beryllium Separation from Beryllium Containing Solution with Solvent Extraction Method%溶剂萃取法从含铍溶液中分离铍

    Institute of Scientific and Technical Information of China (English)

    刘珍珍; 刘勇; 刘牡丹

    2012-01-01

    Beryllium was extracted from the sulphuric acid leaching solution of complex low grade beryllium ore with solvent extraction process. The effecting factors on beryllium single stage extraction rate were researched. The results show that the optimal conditions were pH in aqueous phase of 2?. 5, concentration of beryllium in leaching solution of 1. 5~2. 5 g/L, volume fraction of P204 of 30%, extraction time of 20 min, and W/O=l. In this conditions, more than 98. 50% beryllium is separated by four stage countercur-rent extraction.%采用溶剂萃取法从某复杂低品位铍矿的硫酸浸出液中进行铍的分离,研究了不同因素对铍的单级萃取效果的影响.结果表明,最佳条件为:水相pH=2~2.5、浸出液初始铍浓度1.5~2.5 g/L、P204体积分数30%、萃取时间20 min、相比为1.在此条件下四级逆流萃取后铍萃取率可达到98.50%.

  12. Modes of Occurrence and Geological Origin of Beryllium in Coals from the Pu'an Coalfield, Guizhou, Southwest China

    Institute of Scientific and Technical Information of China (English)

    YANG Jianye

    2007-01-01

    The concentration, modes of occurrence and geological origin of beryllium in five workable coal beds from the Pu'an Coalfield of Guizbou were studied using the inductively coupled-plasma mass spectrometry (ICP-MS), floating and sinking experiments (FSE) and sequential chemical extraction procedures (SCEP). The results show that the average concentration of beryllium in coals from the Pu'an Coalfield is 1.54 μg/g, much lower than that in most Chinese and worldwide coals.Beryllium in the Pu'an coals was not significantly enriched. However, it should be noted that the No. 8 coal bed from the study area has a high concentration of beryllium, 6.89 μg/g, three times higher than the background value of beryllium in coal. Beryllium in coal mainly occurs as organic association and has predominantly originated from coal-forming plants when its concentration is relatively low. The concentration of beryllium occurring as organic association is close to that distributed in inorganic matter when beryllium concentration of coal is similar to its background value, and in addition to coal-forming plants, beryllium is mainly derived from detrital materials of terrigenous origin. When beryllium is anomalously enriched in coal, it mainly occurs as organic association and is derived from volcanic tonsteins leached for a long geological time and then adsorbed by organic matter in peat mire.

  13. Copper allergy from dental copper amalgam?

    Science.gov (United States)

    Gerhardsson, Lars; Björkner, Bert; Karlsteen, Magnus; Schütz, Andrejs

    2002-05-06

    A 65-year-old female was investigated due to a gradually increasing greenish colour change of her plastic dental splint, which she used to prevent teeth grinding when sleeping. Furthermore, she had noted a greenish/bluish colour change on the back of her black gloves, which she used to wipe her tears away while walking outdoors. The investigation revealed that the patient had a contact allergy to copper, which is very rare. She had, however, had no occupational exposure to copper. The contact allergy may be caused by long-term exposure of the oral mucosa to copper from copper-rich amalgam fillings, which were frequently used in childhood dentistry up to the 1960s in Sweden. The deposition of a copper-containing coating on the dental splint may be caused by a raised copper intake from drinking water, increasing the copper excretion in saliva, in combination with release of copper due to electrochemical corrosion of dental amalgam. The greenish colour change of the surface of the splint is probably caused by deposition of a mixture of copper compounds, e.g. copper carbonates. Analysis by the X-ray diffraction technique indicates that the dominant component is copper oxide (Cu2O and CuO). The corresponding greenish/bluish discoloration observed on the back of the patient's gloves may be caused by increased copper excretion in tears.

  14. Tensile and fracture toughness test results of neutron irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Chaouadi, R.; Moons, F.; Puzzolante, J.L. [Centre d`Etude de l`Energie Nucleaire, Mol (Belgium)

    1998-01-01

    Tensile and fracture toughness test results of four Beryllium grades are reported here. The flow and fracture properties are investigated by using small size tensile and round compact tension specimens. Irradiation was performed at the BR2 material testing reactor which allows various temperature and irradiation conditions. The fast neutron fluence (>1 MeV) ranges between 0.65 and 2.45 10{sup 21} n/cm{sup 2}. In the meantime, un-irradiated specimens were aged at the irradiation temperatures to separate if any the effect of temperature from irradiation damage. Test results are analyzed and discussed, in particular in terms of the effects of material grade, test temperature, thermal ageing and neutron irradiation. (author)

  15. Optical properties and structure of beryllium lead silicate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Zhidkov, I. S., E-mail: i.s.zhidkov@urfu.ru [Ural Federal University, Mira Str. 19, Yekaterinburg, 620002, Russia and Institute of Metal Physics, Russian Academy of Sciences-Ural Division, S. Kovalevskoi Str. 18, 620990 Yekaterinburg (Russian Federation); Zatsepin, A. F.; Cholakh, S. O.; Kuznetsova, Yu. A. [Ural Federal University, Mira Str. 19, Yekaterinburg, 620002 (Russian Federation)

    2014-10-21

    Luminescence and optical properties and structural features of (BeO){sub x}(PbO⋅SiO{sub 2}){sub 1−x} glasses (x = 0 ÷ 0.3) are investigated by means of optical absorption and photoluminescence spectroscopy and X-ray diffraction. The regularities of the formation of the optical absorption edge and static disorder are studied. It is shown that the optical absorption and luminescence are determined by transitions between localized states of lead ions. The impact of beryllium oxide on optical and luminescence properties and electronic structure of bands tails is discussed. The presence of two different concentration ranges with various short-range order structure and band tails nature has been established.

  16. Optical properties and structure of beryllium lead silicate glasses

    Science.gov (United States)

    Zhidkov, I. S.; Zatsepin, A. F.; Cholakh, S. O.; Kuznetsova, Yu. A.

    2014-10-01

    Luminescence and optical properties and structural features of (BeO)x(PbOṡSiO2)1-x glasses (x = 0 ÷ 0.3) are investigated by means of optical absorption and photoluminescence spectroscopy and X-ray diffraction. The regularities of the formation of the optical absorption edge and static disorder are studied. It is shown that the optical absorption and luminescence are determined by transitions between localized states of lead ions. The impact of beryllium oxide on optical and luminescence properties and electronic structure of bands tails is discussed. The presence of two different concentration ranges with various short-range order structure and band tails nature has been established.

  17. Modelling of radiation impact on ITER Beryllium wall

    Science.gov (United States)

    Landman, I. S.; Janeschitz, G.

    2009-04-01

    In the ITER H-Mode confinement regime, edge localized instabilities (ELMs) will perturb the discharge. Plasma lost after each ELM moves along magnetic field lines and impacts on divertor armour, causing plasma contamination by back propagating eroded carbon or tungsten. These impurities produce enhanced radiation flux distributed mainly over the beryllium main chamber wall. The simulation of the complicated processes involved are subject of the integrated tokamak code TOKES that is currently under development. This work describes the new TOKES model for radiation transport through confined plasma. Equations for level populations of the multi-fluid plasma species and the propagation of different kinds of radiation (resonance, recombination and bremsstrahlung photons) are implemented. First simulation results without account of resonance lines are presented.

  18. Near real-time fluorescence detection of beryllium

    Energy Technology Data Exchange (ETDEWEB)

    McCleskey, T. M. (Thomas Mark); Ehler, D. S. (Deborah S.); Minogue, E. M. (Edel Mary); Collis, G. E. (Gavin E.); Keizer, T. S. (Timothy S.); Burrell, A. K. (Anthony K.); Sauer, N. N. (Nancy N.); John, K. D. (Kevin D.)

    2004-01-01

    We report on a fluorescent test for beryllium designed for analyzing swipes. The detection is rapid, quantitative and deployable in the field with $5,000 portable fluorimeter. Swipes are placed in a vial and a dilution solution is added. The vials are then rotated for 30 minutes and then syringe filtered. An aliquot of 100 pL is added to a detector solution and fluorescence measured with a portable ocean optics unit. We can readily detect down to 0.02 {micro}g on a filter paper. Interference studies have been carried out with various metals including Al, Fe, Pb, U, Ca, W, Ni, Co and Cu. The technique has proven to be successful under various conditions including a variety of surfaces both in the lab and in field. It is a user-friendly, cost effective method.

  19. Specification for nuclear-grade beryllium oxide powder

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2008-01-01

    1.1 This specification defines the physical and chemical requirements of nuclear-grade beryllium oxide (BeO) powder to be used in fabricating nuclear components. 1.2 This specification does not include requirements for health and safety. , , It recognizes the material as a Class B poison and suggests that producers and users become thoroughly familiar with and comply to applicable federal, state, and local regulations and handling guidelines. 1.3 Special tests and procedures are given in Annex A1 and Annex A2. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

  20. Nuclear charge radius measurements of radioactive beryllium isotopes

    CERN Multimedia

    2002-01-01

    We propose to measure the nuclear charge radii of the beryllium isotopes $^{7,9,10}$Be and the one-neutron halo isotope $^{11}$Be using laser spectroscopy of trapped ions. Ions produced at ISOLDE and ionized with the laser ion source will be cooled and bunched in the radio-frequency buncher of the ISOLTRAP experiment and then transferred into a specially designed Paul trap. Here, they will be cooled to temperatures in the mK range employing sympathetic and direct laser cooling. Precision laser spectroscopy of the isotope shift on the cooled ensemble in combination with accurate atomic structure calculations will provide nuclear charge radii with a precision of better than 3%. This will be the first model-independent determination of a one-neutron halo nuclear charge radius.

  1. Notched strength of beryllium powder and ingot sheets.

    Science.gov (United States)

    Moss, R. G.

    1972-01-01

    The effects of notches in thin beryllium sheets were studied as functions of material variables and notch severity. Double edge notched samples having stress concentration factors of 1.0 to 15.4 were prepared by milling to size, etching, and electrical discharge machining the notches. Strength was not reduced greatly by sharp notches, and duller notches were more deleterious than sharp notches. The trend was for reduced strength for dull notches, increased strength for sharper notches, and reduced strength for very sharp notches. Differences in material purity or source of the sheet had little affect on notch sensitivity. The most important factors appear to be oxide content and directionality of the sheet microstructure; high oxide content and highly directional microstructure tend to give more notch sensitivity than low oxide content, and more bidirectional microstructure. Postulated causes of the change in notched/unnotched strength are given.

  2. Electromagnetic properties of the Beryllium-11 nucleus in Halo EFT

    Directory of Open Access Journals (Sweden)

    Hammer H.-W.

    2010-04-01

    Full Text Available We compute electromagnetic properties of the Beryllium-11 nucleus using an effective field theory that exploits the separation of scales in this halo system. We fix the parameters of the EFT from measured data on levels and scattering lengths in the 10Be plus neutron system. We then obtain predictions for the B(E1 strength of the 1/2+ to 1/2− transition in the 11Be nucleus. We also compute the charge radius of the ground state of 11Be. Agreement with experiment within the expected accuracy of a leading-order computation in this EFT is obtained. We also indicate how higher-order corrections that affect both s-wave and p-wave 10 Be-neutron interactions will affect our results.

  3. Damage production in atomic displacement cascades in beryllium

    Directory of Open Access Journals (Sweden)

    V.A. Borodin

    2016-12-01

    Full Text Available The paper presents the results of a molecular dynamics simulation of cascade damage production in beryllium caused by self-ion recoils in the energy range of 0.5–3keV. It is demonstrated that point defects are produced in Be preferentially in well-separated subcascades generated by secondary and higher order recoils. A linear dependence of the point defect number on the primary recoil energy is obtained with the slope that corresponds to formal atom displacement energy of ∼21eV. Most of the damage is created as single defects and the relatively high part of created point defects (∼50% survives the correlated recombination following the ballistic cascade stage and becomes freely-migrating.

  4. Retrospective beryllium exposure assessment at the Rocky Flats Environmental Technology site

    Energy Technology Data Exchange (ETDEWEB)

    Barnard, A.E.; Torma-Krajewski, J. [Department of Energy, Rocky Flats Field Office, Golden, CO (United States); Viet, S.M. [M.H. Chew & Associates, Inc., Golden, CO (United States)

    1997-05-01

    Since the 1960`s, beryllium machining was performed to make nuclear weapon components at the Department of Energy (DOE) Rocky Flats Plant. Beryllium exposure was assessed via fixed airhead (FAH) sampling in which the filter cassette was affixed to the machine, generally within a few feet of the worker`s breathing zone. Approximately 500,000 FAH samples were collected for beryllium over three decades. From 1984 to 1987, personal breathing zone (PBZ) samples were also collected as part of the evaluation of a new high velocity/low volume local exhaust ventilation (HV/LV LEV) system. The purpose of this study was to determine how the two types of sampling data could be used for an exposure assessment in the beryllium shop.

  5. Solvent extraction of beryllium from malonate solutions with liquid anion exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Rao, R.R.; Khopkar, S.M.

    1983-12-01

    Beryllium was quantitatively extracted at pH 5.5-7.0 in microgram amounts with 0.06 M Aliquat 336S in xylene from 5 x 10/sup -3/ M malonic acid solution, stripped with 0.5 M hydrochloric acid, and determined spectrophotometrically at 523 nm as its complex with thorin. Those metals which could not form anionic complexes with malonic acid and were not extracted with beryllium at pH 6.5 were separated from it. Metals forming weak malonato complexes were scrubbed from the organic phase with water. The elements like bismuth, antimony, iron, uranium, gallium, and vanadium which form strong malonato complexes were separated by selective stripping with hydrochloric, sulfuric, or nitric acid. The method was extended for the analysis of beryllium in beryl and beryllium alloys. 1 figure, 6 tables.

  6. Cryogenic Fracture Toughness Evaluation of an Investment Cast Aluminum-Beryllium Alloy for Structural Applications

    Science.gov (United States)

    Gamwell, Wayne; McGill, Preston

    2006-01-01

    This document is a viewgraph presentation that details the fracture toughness of Aluminum-Beryllium Alloy for use in structures at cryogenic temperatures. Graphs and charts are presented in the presentation

  7. Estimations of neutron yield from beryllium target irradiated by SPring-8 hard synchrotron radiation

    CERN Document Server

    Gryaznykh, D A; Plokhoi, V V

    2000-01-01

    The possibility of creating a neutron source based on ''SPring-8'' synchrotron radiation interaction with beryllium targets is discussed. The possible neutron yield is estimated to be of order 10 sup 1 sup 2 s sup - sup 1 .

  8. Neutron activation analysis: Modelling studies to improve the neutron flux of Americium–Beryllium source

    National Research Council Canada - National Science Library

    Abdessamad Didi; Ahmed Dadouch; Otman Jaï; Jaouad Tajmouati; Hassane El Bekkouri

    2017-01-01

    Americium–beryllium (Am-Be; n, γ) is a neutron emitting source used in various research fields such as chemistry, physics, geology, archaeology, medicine, and environmental monitoring, as well as in the forensic sciences...

  9. REMOVAL OF BERYLLIUM FROM DRINKING WATER BY CHEMICAL COAGULATION AND LIME SOFTENING

    Science.gov (United States)

    The effectiveness of conventional drinking water treatment and lime softening was evaluated for beryllium removal from two drinking water sources. ar test studies were conducted to determine how common coagulants (aluminum sulfate and ferric chloride and lime softening performed ...

  10. The impact of particle size selective sampling methods on occupational assessment of airborne beryllium particulates.

    Science.gov (United States)

    Sleeth, Darrah K

    2013-05-01

    In 2010, the American Conference of Governmental Industrial Hygienists (ACGIH) formally changed its Threshold Limit Value (TLV) for beryllium from a 'total' particulate sample to an inhalable particulate sample. This change may have important implications for workplace air sampling of beryllium. A history of particle size-selective sampling methods, with a special focus on beryllium, will be provided. The current state of the science on inhalable sampling will also be presented, including a look to the future at what new methods or technology may be on the horizon. This includes new sampling criteria focused on particle deposition in the lung, proposed changes to the existing inhalable convention, as well as how the issues facing beryllium sampling may help drive other changes in sampling technology.

  11. IRIS Toxicological Review of Beryllium and Compounds (2008 External Review Draft)

    Science.gov (United States)

    EPA is conducting a peer review and public comment of the scientific basis supporting the human health hazard and dose-response assessment of Beryllium that when finalized will appear on the Integrated Risk Information System (IRIS) database.

  12. First beryllium capsule implosions on the National Ignition Facility

    Science.gov (United States)

    Kline, J. L.; Yi, S. A.; Simakov, A. N.; Olson, R. E.; Wilson, D. C.; Kyrala, G. A.; Perry, T. S.; Batha, S. H.; Zylstra, A. B.; Dewald, E. L.; Tommasini, R.; Ralph, J. E.; Strozzi, D. J.; MacPhee, A. G.; Callahan, D. A.; Hinkel, D. E.; Hurricane, O. A.; Milovich, J. L.; Rygg, J. R.; Khan, S. F.; Haan, S. W.; Celliers, P. M.; Clark, D. S.; Hammel, B. A.; Kozioziemski, B.; Schneider, M. B.; Marinak, M. M.; Rinderknecht, H. G.; Robey, H. F.; Salmonson, J. D.; Patel, P. K.; Ma, T.; Edwards, M. J.; Stadermann, M.; Baxamusa, S.; Alford, C.; Wang, M.; Nikroo, A.; Rice, N.; Hoover, D.; Youngblood, K. P.; Xu, H.; Huang, H.; Sio, H.

    2016-05-01

    The first indirect drive implosion experiments using Beryllium (Be) capsules at the National Ignition Facility confirm the superior ablation properties and elucidate possible Be-ablator issues such as hohlraum filling by ablator material. Since the 1990s, Be has been the preferred Inertial Confinement Fusion (ICF) ablator because of its higher mass ablation rate compared to that of carbon-based ablators. This enables ICF target designs with higher implosion velocities at lower radiation temperatures and improved hydrodynamic stability through greater ablative stabilization. Recent experiments to demonstrate the viability of Be ablator target designs measured the backscattered laser energy, capsule implosion velocity, core implosion shape from self-emission, and in-flight capsule shape from backlit imaging. The laser backscatter is similar to that from comparable plastic (CH) targets under the same hohlraum conditions. Implosion velocity measurements from backlit streaked radiography show that laser energy coupling to the hohlraum wall is comparable to plastic ablators. The measured implosion shape indicates no significant reduction of laser energy from the inner laser cone beams reaching the hohlraum wall as compared with plastic and high-density carbon ablators. These results indicate that the high mass ablation rate for beryllium capsules does not significantly alter hohlraum energetics. In addition, these data, together with data for low fill-density hohlraum performance, indicate that laser power multipliers, required to reconcile simulations with experimental observations, are likely due to our limited understanding of the hohlraum rather than the capsule physics since similar multipliers are needed for both Be and CH capsules as seen in experiments.

  13. First beryllium capsule implosions on the National Ignition Facility

    Energy Technology Data Exchange (ETDEWEB)

    Kline, J. L.; Yi, S. A.; Simakov, A. N.; Olson, R. E.; Wilson, D. C.; Kyrala, G. A.; Perry, T. S.; Batha, S. H.; Zylstra, A. B.; Dewald, E. L.; Tommasini, R.; Ralph, J. E.; Strozzi, D. J.; MacPhee, A. G.; Callahan, D. A.; Hinkel, D. E.; Hurricane, O. A.; Milovich, J. L.; Rygg, J. R.; Khan, S. F.; Haan, S. W.; Celliers, P. M.; Clark, D. S.; Hammel, B. A.; Kozioziemski, B.; Schneider, M. B.; Marinak, M. M.; Rinderknecht, H. G.; Robey, H. F.; Salmonson, J. D.; Patel, P. K.; Ma, T.; Edwards, M. J.; Stadermann, M.; Baxamusa, S.; Alford, C.; Wang, M.; Nikroo, A.; Rice, N.; Hoover, D.; Youngblood, K. P.; Xu, H.; Huang, H.; Sio, H.

    2016-05-01

    The first indirect drive implosion experiments using Beryllium (Be) capsules at the National Ignition Facility confirm the superior ablation properties and elucidate possible Be-ablator issues such as hohlraum filling by ablator material. Since the 1990s, Be has been the preferred Inertial Confinement Fusion (ICF) ablator because of its higher mass ablation rate compared to that of carbon-based ablators. This enables ICF target designs with higher implosion velocities at lower radiation temperatures and improved hydrodynamic stability through greater ablative stabilization. Recent experiments to demonstrate the viability of Be ablator target designs measured the backscattered laser energy, capsule implosion velocity, core implosion shape from self-emission, and in-flight capsule shape from backlit imaging. The laser backscatter is similar to that from comparable plastic (CH) targets under the same hohlraum conditions. Implosion velocity measurements from backlit streaked radiography show that laser energy coupling to the hohlraum wall is comparable to plastic ablators. The measured implosion shape indicates no significant reduction of laser energy from the inner laser cone beams reaching the hohlraum wall as compared with plastic and high-density carbon ablators. These results indicate that the high mass ablation rate for beryllium capsules does not significantly alter hohlraum energetics. In addition, these data, together with data for low fill-density hohlraum performance, indicate that laser power multipliers, required to reconcile simulations with experimental observations, are likely due to our limited understanding of the hohlraum rather than the capsule physics since similar multipliers are needed for both Be and CH capsules as seen in experiments.

  14. Copper Products Capacity Expansion Stimulate the Copper Consumption

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    <正>The dramatic growth of copper consumption in China can directly be seen from the expansion of copper products capacity.According to sta- tistics,in the past 4 years,the improvement on the balance of trade on copper bar,copper,and copper alloy and copper wire & cable has driven the growth of copper consumption a lot.

  15. Characterization of phagolysosomal simulant fluid for study of beryllium aerosol particle dissolution.

    Science.gov (United States)

    Stefaniak, A B; Guilmette, R A; Day, G A; Hoover, M D; Breysse, P N; Scripsick, R C

    2005-02-01

    A simulant of phagolysosomal fluid is needed for beryllium particle dissolution research because intraphagolysosomal dissolution is believed to be a necessary step in the cellular immune response associated with development of chronic beryllium disease. Thus, we refined and characterized a potassium hydrogen phthalate (KHP) buffered solution with pH 4.55, termed phagolysosomal simulant fluid (PSF), for use in a static dissolution technique. To characterize the simulant, beryllium dissolution in PSF was compared to dissolution in the J774A.1 murine cell line. The effects of ionic composition, buffer strength, and the presence of the antifungal agent alkylbenzyldimethylammonium chloride (ABDC) on beryllium dissolution in PSF were evaluated. Beryllium dissolution in PSF was not different from dissolution in the J774A.1 murine cell line (p = 0.78) or from dissolution in another simulant having the same pH but different ionic composition (p = 0.73). A buffer concentration of 0.01-M KHP did not appear adequate to maintain pH under all conditions. There was no difference between dissolution in PSF with 0.01-M KHP and 0.02-M KHP (p = 0.12). At 0.04-M KHP, beryllium dissolution was increased relative to 0.02-M KHP (p = 0.02). Use of a 0.02-M KHP buffer concentration in the standard formulation for PSF provided stability in pH without alteration of the dissolution rate. The presence of ABDC did not influence beryllium dissolution in PSF (p = 0.35). PSF appears to be a useful and appropriate model of in vitro beryllium dissolution when using a static dissolution technique. In addition, the critical approach used to evaluate and adjust the composition of PSF may serve as a framework for characterizing PSF to study dissolution of other metal and oxide particles.

  16. Calculated power distribution of a thermionic, beryllium oxide reflected, fast-spectrum reactor

    Science.gov (United States)

    Mayo, W.; Lantz, E.

    1973-01-01

    A procedure is developed and used to calculate the detailed power distribution in the fuel elements next to a beryllium oxide reflector of a fast-spectrum, thermionic reactor. The results of the calculations show that, although the average power density in these outer fuel elements is not far from the core average, the power density at the very edge of the fuel closest to the beryllium oxide is about 1.8 times the core avearge.

  17. Impact of beryllium reflector ageing on Safari–1 reactor core parameters / L.E. Moloko

    OpenAIRE

    Moloko, Lesego Ernest

    2011-01-01

    The build–up of 6Li and 3He, that is, the strong thermal neutron absorbers or the so called "neutron poisons", in the beryllium reflector changes the physical characteristics of the reactor, such as reactivity, neutron spectra, neutron flux level, power distribution, etc.; furthermore,gaseous isotopes such as 3H and 4He induce swelling and embrittlement of the reflector. The SAFARI–1 research reactor, operated by Necsa at Pelindaba in South Africa, uses a beryllium reflector on...

  18. Suivi médical de salariés exposés au beryllium

    OpenAIRE

    2009-01-01

    International audience; Purpose of the study: determination of a systematised procedure for medical follow-up of beryllium-exposed workers. Method: a medical follow-up of workers from a factory machining beryllium (Be) either plain or as an alloy started in 2001. Be Lymphocyte Proliferation Tests (LPT) were performed for screening Be sensitisation and were calculated again according to 1142-2001 speciation of the American Department Of Energy. A working group included occupational physicians,...

  19. Antwerp Copper Plates

    DEFF Research Database (Denmark)

    Wadum, Jørgen

    1999-01-01

    In addition to presenting a short history of copper paintings, topics detail artists’ materials and techniques, as well as aspects of the copper industry, including mining, preparation and trade routes.......In addition to presenting a short history of copper paintings, topics detail artists’ materials and techniques, as well as aspects of the copper industry, including mining, preparation and trade routes....

  20. Sensitive detection of beryllium using a fiber optic liquid waveguide cell.

    Science.gov (United States)

    Deng, Gang; Wei, Lily; Collins, Greg E

    2003-05-28

    The metallochromic chelating agent, Chromazurol S, has been utilized in conjunction with a fiber optic liquid waveguide capillary cell to enable the sensitive detection of beryllium in solution (30 ng l(-1) detection limit) and following extraction from a contaminated plexiglas surface (0.5 ng cm(-2) detection limit). The addition of a cationic surfactant, cetylpyridinium chloride, to Chromazurol S at pH 10 in Tris-HCl buffer results in the formation of two bathochromic peaks in the visible spectrum following metal chelation by beryllium. The first absorbance band, at 515 nm, is intermediate in nature, permitting maximal sensitivity for low beryllium concentrations, but diminishing in intensity at concentrations above 100 mug l(-1). The second absorbance band, centered at 610 nm, dominates for beryllium concentrations of 100 mug l(-1) and above. Experimental conditions including pH, buffer type, additive surfactants, masking agents, and dye concentration were investigated in order to optimize detection sensitivity and selectivity. A fiber optic spectrometer is used with both a liquid waveguide capillary cell and 1 cm cuvette cell, to give a sensitive and broad dynamic range for beryllium detection that capitalizes on both beryllium metal chelate absorbance bands formed under these conditions.

  1. Extraction and optical fluorescence method for the measurement of trace beryllium in soils.

    Science.gov (United States)

    Agrawal, Anoop; Cronin, John P; Agrawal, Akshay; Tonazzi, Juan C L; Adams, Lori; Ashley, Kevin; Brisson, Michael J; Duran, Brandy; Whitney, Gary; Burrell, Anthony K; McCleskey, T Mark; Robbins, James; White, Kenneth T

    2008-03-15

    Beryllium metal and beryllium oxide are important industrial materials used in a variety of applications in the electronics, nuclear energy, and aerospace industries. These materials are highly toxic, they must be disposed of with care, and exposed workers need to be protected. Recently, a new analytical method was developed that uses dilute ammonium bifluoride for extraction of beryllium and a high quantum yield optical fluorescence reagent to determine trace amounts of beryllium in airborne and surface samples. The sample preparation and analysis procedure was published by both ASTM International and the National Institute for Occupational Safety and Health (NIOSH). The main advantages of this method are its sensitivity, simplicity, use of lower toxicity materials, and low capital costs. Use of the technique for analyzing soils has been initiated to help meet a need at several of the U.S. Department of Energy legacy sites. So far this work has mainly concentrated on developing a dissolution protocol for effectively extracting beryllium from a variety of soils and sediments so that these can be analyzed by optical fluorescence. Certified reference materials (CRM) of crushed rock and soils were analyzed for beryllium content using fluorescence, and results agree quantitatively with reference values.

  2. The Status of Beryllium Research for Fusion in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Glen R. Longhurst

    2003-12-01

    Use of beryllium in fusion reactors has been considered for neutron multiplication in breeding blankets and as an oxygen getter for plasma-facing surfaces. Previous beryllium research for fusion in the United States included issues of interest to fission (swelling and changes in mechanical and thermal properties) as well as interactions with plasmas and hydrogen isotopes and methods of fabrication. When the United States formally withdrew its participation in the International Thermonuclear Experimental Reactor (ITER) program, much of this effort was terminated. The focus in the U.S. has been mainly on toxic effects of beryllium and on industrial hygiene and health-related issues. Work continued at the INEEL and elsewhere on beryllium-containing molten salts. This activity is part of the JUPITER II Agreement. Plasma spray of ITER first wall samples at Los Alamos National Laboratory has been performed under the European Fusion Development Agreement. Effects of irradiation on beryllium structure are being studied at Oak Ridge National Laboratory. Numerical and phenomenological models are being developed and applied to better understand important processes and to assist with design. Presently, studies are underway at the University of California Los Angeles to investigate thermo-mechanical characteristics of beryllium pebble beds, similar to research being carried out at Forschungszentrum Karlsruhe and elsewhere. Additional work, not funded by the fusion program, has dealt with issues of disposal, and recycling.

  3. Combined effects of gallic acid and propolis on beryllium-induced hepatorenal toxicity.

    Science.gov (United States)

    Nirala, Satendra K; Li, Peiqiang; Bhadauria, Monika; Guo, Guangqin

    2008-09-01

    The combined effect of gallic acid (3,4,5-trihydroxy benzoic acid; GA; 50 mg kg(-1) i.p.) and propolis (200 mg kg(-1) p.o.) was evaluated against beryllium-induced biochemical and morphological alterations in the liver and kidney. Female albino rats were exposed to beryllium nitrate (1 mg kg(-1) i.p.) daily for 28 days followed by treatment with the above mentioned therapeutic agents either individually or in combination for five consecutive days. Exposure to beryllium increased its concentration in the serum, liver and kidney and caused significant alterations in cytochrome P450 enzymes, microsomal lipid peroxidation and protein contents. Beryllium administration significantly altered the aspartate aminotransaminase, alanine aminotransaminase, lactate dehydrogenase, γ-grutamy1 transpeptidase, bilirubin, creatinine and urea in serum, and the activity of acid phosphatase, alkaline phosphatase, adenosine triphosphatase, glucose-6-phophatase and succinic dehydrogenase, triglycerides, cholesterol, protein contents, glycogen contents, lipid peroxidation and glutathione level in the liver and kidney. Beryllium exposure induced severe alterations in hepatorenal morphology, revealing its toxic consequences at a cellular level. Individual administration of GA and propolis reduced the effects on the studied parameters to a degree. Interestingly, GA in conjunction with propolis reversed the alterations in all of the variables examined, highlighting the beneficial effects of combined therapy over monotherapy in the alleviation of beryllium-induced systemic toxicity. © 2008 ISZS, Blackwell Publishing and IOZ/CAS.

  4. Synergistic effects of ferritin and propolis in modulation of beryllium induced toxicogenic alterations.

    Science.gov (United States)

    Nirala, Satendra Kumar; Bhadauria, Monika

    2008-09-01

    Synergistic therapeutic potential of ferritin (5mg/kg, i.p.) and propolis (honeybee hive product; 200mg/kg, p.o.) was analyzed to encounter the beryllium induced biochemical and ultra morphological alterations. Female albino rats were exposed to beryllium nitrate (1mg/kg, i.p.) daily for 28 days followed by treatment of above mentioned therapeutic agents either individually or in combination for five consecutive days. Exposure to beryllium increased its concentration in serum, liver and kidney and significantly altered the activities of CYP2E1 and CYP1A2 enzymes, microsomal lipid peroxidation and microsomal proteins. Activities of aspartate aminotransferase, alanine aminotransferase, alkaline phosphatase, lactate dehydrogenase, gamma-glutamyl transpeptidase, bilirubin, protein, creatinine and urea in serum as well as hemoglobin and blood glucose level; activity of acid phosphatase, alkaline phosphatase, adenosine triphosphatase, glucose-6-phosphatase and succinic dehydrogenase, total triglycerides, total cholesterol, total protein contents, glycogen contents, lipid peroxidation and glutathione level in liver and kidney were significantly altered after beryllium administration. Beryllium exposure severely altered ultramorphology of liver and kidney that proved its toxic consequences at cellular level. Ferritin in combination with propolis dramatically reversed the alterations of these variables towards control in a synergistic manner concluding its beneficial effects over monotherapy in attenuating beryllium induced systemic toxicity.

  5. Pharmacological intervention of tiferron and propolis to alleviate beryllium-induced hepatorenal toxicity.

    Science.gov (United States)

    Nirala, Satendra Kumar; Bhadauria, Monika; Shukla, Sangeeta; Agrawal, Om Prakash; Mathur, Asha; Li, Pei Qiang; Mathur, Ramesh

    2008-08-01

    Intervention of chelating agent tiferron (sodium-4,5-dihydroxy-1,3-benzene disulfonate; 300 mg/kg, intraperitoneal) with propolis (honey beehive product; 200 mg/kg, p.o.) was evaluated to encounter the characteristic biochemical and ultra-morphological alterations following subchronic exposure to beryllium. Female albino rats were challenged with beryllium nitrate (1 mg/kg, i.p.) daily for 28 days followed by treatment of the above-mentioned therapeutic agents either individually or in combination for five consecutive days. Exposure to beryllium increased its concentration in the serum, liver and kidney, and caused significant alterations in cytochrome P450 activity, microsomal lipid peroxidation and proteins. Activities of alkaline phosphatase, lactate dehydrogenase, gamma-glutamyl transpeptidase, bilirubin, creatinine and urea in the serum and activity of acid phosphatase, alkaline phosphatase, adenosine triphosphatase, glucose-6-phophatase and succinic dehydrogenase in the liver and kidney were significantly altered after beryllium administration. Beryllium exposure also induced severe hepatorenal alterations at histopathological and ultra-morphological level. Tiferron along with propolis dramatically reversed the alterations in all the variables more towards control rather than their individual treatment. The study concludes that pharmacological intervention of tiferron and propolis is beneficial in attenuating beryllium-induced systemic toxicity.

  6. Characterization of beryllium deformation using in-situ x-ray diffraction

    Energy Technology Data Exchange (ETDEWEB)

    Magnuson, Eric Alan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Brown, Donald William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Clausen, Bjorn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Sisneros, Thomas A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Park, Jun-Sang [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-08-24

    Beryllium’s unique mechanical properties are extremely important in a number of high performance applications. Consequently, accurate models for the mechanical behavior of beryllium are required. However, current models are not sufficiently microstructure aware to accurately predict the performance of beryllium under a range of processing and loading conditions. Previous experiments conducted using the SMARTS and HIPPO instruments at the Lujan Center(LANL), have studied the relationship between strain rate and texture development, but due to the limitations of neutron diffraction studies, it was not possible to measure the response of the material in real-time. In-situ diffraction experiments conducted at the Advanced Photon Source have allowed the real time measurement of the mechanical response of compressed beryllium. Samples of pre-strained beryllium were reloaded orthogonal to their original load path to show the reorientation of already twinned grains. Additionally, the in-situ experiments allowed the real time tracking of twin evolution in beryllium strained at high rates. The data gathered during these experiments will be used in the development and validation of a new, microstructure aware model of the constitutive behavior of beryllium.

  7. Copper and copper proteins in Parkinson's disease.

    Science.gov (United States)

    Montes, Sergio; Rivera-Mancia, Susana; Diaz-Ruiz, Araceli; Tristan-Lopez, Luis; Rios, Camilo

    2014-01-01

    Copper is a transition metal that has been linked to pathological and beneficial effects in neurodegenerative diseases. In Parkinson's disease, free copper is related to increased oxidative stress, alpha-synuclein oligomerization, and Lewy body formation. Decreased copper along with increased iron has been found in substantia nigra and caudate nucleus of Parkinson's disease patients. Copper influences iron content in the brain through ferroxidase ceruloplasmin activity; therefore decreased protein-bound copper in brain may enhance iron accumulation and the associated oxidative stress. The function of other copper-binding proteins such as Cu/Zn-SOD and metallothioneins is also beneficial to prevent neurodegeneration. Copper may regulate neurotransmission since it is released after neuronal stimulus and the metal is able to modulate the function of NMDA and GABA A receptors. Some of the proteins involved in copper transport are the transporters CTR1, ATP7A, and ATP7B and the chaperone ATOX1. There is limited information about the role of those biomolecules in the pathophysiology of Parkinson's disease; for instance, it is known that CTR1 is decreased in substantia nigra pars compacta in Parkinson's disease and that a mutation in ATP7B could be associated with Parkinson's disease. Regarding copper-related therapies, copper supplementation can represent a plausible alternative, while copper chelation may even aggravate the pathology.

  8. Erosion behaviour of ultrathin carbon layers and hydrogen retention in beryllium; Untersuchungen zur Erosion ultraduenner Kohlenstoffschichten und Wasserstoffrueckhaltung in Beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Reinelt, Matthias

    2008-04-16

    Plasma-wall-interaction plays an important role on the way to technical feasibility of thermonuclear fusion. In this context, the erosion behavior of few nanometer thin amorphous carbon layers on different metallic substrates by energetic deuterium and helium ions is investigated. Several aspects of the interaction are distinguishable by XPS. Ion induced carbide formation is governed by kinematic intermixing of carbon and metal substrate. Several methods of quantification of XPS measurements are developed and discussed. Comparison of results from these methods with NRA measurements show that surface roughness and implantation of particles into the carbon layer and intermixing zone influence the XPS measurements, which are sensitive to parameters such as material density. The retention of 1 keV deuterium ions implanted into single crystalline and cleaned beryllium at room temperature is investigated by temperature programmed desorption (TPD). The residual BeO coverage was 0.2 ML. The retention is 78% at low fluences and saturates above a bombardment with a fluence of 2.10{sup 17} cm{sup -2}. The retained maximum areal density is 2.10{sup 17} cm{sup -2}. Above 900 K, no deuterium is retained in the sample. An onset of self diffusion is observed at this temperature and metallic beryllium from the bulk segregates though thin BeO layers on the surface. From deuterium desorption traces, retention mechanisms are obtained. The measured TPDspectra are modeled by TMAP7 and rate equations to obtain activation energies for the release processes. From these, binding energies for the system Be-D are derived. Up to a implantation fluence of 1.10{sup 17} cm{sup -2}, deuterium is trapped in ion induced defects in the beryllium lattice with binding energies of 1.69 eV and 1.86 eV and release temperatures of 770 K and 840 K, respectively. The occupation of these states shows a different isotope behavior for {sup 1}H and {sup 2}H. The states are filled by diffusion of deuterium at the

  9. Solder joint technology materials, properties, and reliability

    CERN Document Server

    Tu, King-Ning

    2007-01-01

    Solder joints are ubiquitous in electronic consumer products. The European Union has a directive to ban the use of Pb-based solders in these products on July 1st, 2006. There is an urgent need for an increase in the research and development of Pb-free solders in electronic manufacturing. For example, spontaneous Sn whisker growth and electromigration induced failure in solder joints are serious issues. These reliability issues are quite complicated due to the combined effect of electrical, mechanical, chemical, and thermal forces on solder joints. To improve solder joint reliability, the science of solder joint behavior under various driving forces must be understood. In this book, the advanced materials reliability issues related to copper-tin reaction and electromigration in solder joints are emphasized and methods to prevent these reliability problems are discussed.

  10. Fracture toughness of copper-base alloys for ITER applications: A preliminary report

    Energy Technology Data Exchange (ETDEWEB)

    Alexander, D.J.; Zinkle, S.J.; Rowcliffe, A.F. [Oak Ridge National Lab., TN (United States)

    1997-04-01

    Oxide-dispersion strengthened copper alloys and a precipitation-hardened copper-nickel-beryllium alloy showed a significant reduction in toughness at elevated temperature (250{degrees}C). This decrease in toughness was much larger than would be expected from the relatively modest changes in the tensile properties over the same temperature range. However, a copper-chromium-zirconium alloy strengthened by precipitation showed only a small decrease in toughness at the higher temperatures. The embrittled alloys showed a transition in fracture mode, from transgranular microvoid coalescence at room temperature to intergranular with localized ductility at high temperatures. The Cu-Cr-Zr alloy maintained the ductile microvoid coalescence failure mode at all test temperatures.

  11. Brazing Inconel 625 Using the Copper Foil

    Science.gov (United States)

    Chen, Wen-Shiang; Wang, Cheng-Yen; Shiue, Ren-Kae

    2013-12-01

    Brazing Inconel 625 (IN-625) using the copper foil has been investigated in this research. The brazed joint is composed of nanosized CrNi3 precipitates and Cr/Mo/Nb/Ni quaternary compound in the Cu/Ni-rich matrix. The copper filler 50 μm in thickness is enough for the joint filling. However, the application of Cu foil 100 μm in thickness has little effect on the shear strength of the brazed joint. The specimen brazed at 1433 K (1160 °C) for 1800 seconds demonstrates the best shear strength of 470 MPa, and its fractograph is dominated by ductile dimple fracture with sliding marks. Decreasing the brazing temperature slightly decreases the shear strength of the brazed joint due to the presence of a few isolated solidification shrinkage voids smaller than 15 μm. Increasing the brazing temperature, especially for the specimen brazed at 1473 K (1200 °C), significantly deteriorates the shear strength of the joint below 260 MPa because of coalescence of isothermal solidification shrinkage voids in the joint. The Cu foil demonstrates potential in brazing IN-625 for industrial application.

  12. Ceramic joints

    Science.gov (United States)

    Miller, Bradley J.; Patten, Jr., Donald O.

    1991-01-01

    Butt joints between materials having different coefficients of thermal expansion are prepared having a reduced probability of failure of stress facture. This is accomplished by narrowing/tapering the material having the lower coefficient of thermal expansion in a direction away from the joint interface and not joining the narrow-tapered surface to the material having the higher coefficient of thermal expansion.

  13. Negative transferred arc cleaning: a method for roughening and removing surface contamination from beryllium and other metallic surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Castro, R.G.; Hollis, K.J.; Maggiore, C.J.; Ayala, A.; Bartram, B.D. [Los Alamos National Lab., NM (United States). Materials Science and Technology Div.; Doerner, R.P. [California Univ., San Diego (United States). Fusion Energy Res.

    2000-04-01

    TA cleaning has been investigated for preparing the surface of beryllium plasma facing components (PFC's) inside of the international thermonuclear experimental reactor (ITER) prior to depositing beryllium by plasma spraying. Plasma spraying of beryllium was evaluated during the ITER engineering design activity (EDA) for in-situ repair and initial fabrication of the beryllium first wall armor. Results have shown that surface roughening of beryllium, during the TA cleaning process, can result in bond strengths greater than 100 MPa between beryllium surfaces and plasma sprayed beryllium. In addition, the TA cleaning process was shown to be an effective method for removing contaminate layers of carbon and tungsten from the surface of beryllium. Investigations have been performed to characterize the different arc-types that occur during the TA cleaning process (type I, I and III arcs) and the effectiveness of the TA cleaning process for potentially removing co-deposited layers of carbon and deuterium from the surface of beryllium, stainless steel and tungsten. (orig.)

  14. Adsorption of beryllium atoms and clusters both on graphene and in a bilayer of graphite investigated by DFT.

    Science.gov (United States)

    Ferro, Yves; Fernandez, Nicolas; Allouche, Alain; Linsmeier, Christian

    2013-01-09

    We herein investigate the interaction of beryllium with a graphene sheet and in a bilayer of graphite by means of periodic DFT calculations. In all cases, we find the beryllium atoms to be more weakly bonded on graphene than in the bilayer. Be(2) forms both magnetic and non-magnetic structures on graphene depending on the geometrical configuration of adsorption. We find that the stability of the Be/bilayer system increases with the size of the beryllium clusters inserted into the bilayer of graphite. We also find a charge transfer from beryllium to the graphite layers. All these results are analysed in terms of electronic structure.

  15. Temporomandibular Joint, Closed

    Science.gov (United States)

    ... Gallery > Oral Health > The Temporomandibular Joint, Closed The Temporomandibular Joint, Closed Main Content Title: The Temporomandibular Joint, Closed Description: The temporomandibular joint connects the lower ...

  16. Assessment of Lead and Beryllium deposition and adsorption to exposed stream channel sediments

    Science.gov (United States)

    Pawlowski, E.; Karwan, D. L.

    2016-12-01

    The fallout radionuclides Beryllium-7 and Lead-210 have been shown to be effective sediment tracers that readily bind to particles. The adsorption capacity has primarily been assessed in marine and coastal environments with an important assumption being the radionuclides' uniform spatial distribution as fallout from the atmosphere. This neglects localized storm events that may mine stratospheric reserves creating variable distributions. To test this assumption atmospheric deposition is collected at the University of Minnesota St. Paul Campus weather station during individual storm events and subsequently analyzed for Beryllium-7 and Lead-210. This provides further insight into continental effects on radionuclide deposition. The study of Beryllium-7 and Lead-210 adsorption in marine and coastal environments has provided valuable insights into the processes that influence the element's binding to particles but research has been limited in freshwater river environments. These environments have greater variation in pH, iron oxide content, and dissolved organic carbon (DOC) levels which have been shown to influence the adsorption of Beryllium and Lead in marine settings. This research assesses the adsorption of Beryllium and Lead to river sediments collected from in-channel deposits by utilizing batch experiments that mimic the stream conditions from which the deposits were collected. Soils were collected from Difficult Run, VA, and the West Swan River, MN. Agitating the soils in a controlled solution of known background electrolyte and pH while varying the level of iron oxides and DOC in step provides a better understanding of the sorption of Lead and Beryllium under the conditions found within freshwater streams. Pairing the partitioning of Lead and Beryllium with their inputs to streams via depositional processes, from this study and others, allows for their assessment as possible sediment tracers and age-dating tools within the respective watersheds.

  17. Monitoring beryllium during site cleanup and closure using a real-time analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Schlager, R.J.; Sappey, A.D.; French, P.D. [ADA Technologies, Inc., Englewood, CO (United States)

    1998-12-31

    Beryllium metal has a number of unique properties that have been exploited for use in commercial and government applications. Airborne beryllium particles can represent a significant human health hazard if deposited in the lungs. These particles can cause immunologically-mediated chronic granulomatous lung disease (chronic beryllium disease). Traditional methods of monitoring airborne beryllium involve collecting samples of air within the work area using a filter. The filter then undergoes chemical analysis to determine the amount of beryllium collected during the sampling period. These methods are time-consuming and results are known only after a potential exposure has occurred. The need for monitoring exposures in real time has prompted government and commercial companies to develop instrumentation that will allow for the real time assessment of short-term exposures so that adequate protection for workers in contaminated environments can be provided. Such an analyzer provides a tool that will allow government and commercial sites to be cleaned up in a more safe and effective manner since exposure assessments can be made instantaneously. This paper describes the development and initial testing of an analyzer for monitoring airborne beryllium using a technique known as Laser-Induced Breakdown Spectroscopy (LIBS). Energy from a focused, pulsed laser is used to vaporize a sample and create an intense plasma. The light emitted from the plasma is analyzed to determine the quantity of beryllium in the sampled air. A commercial prototype analyzer has been fabricated and tested in a program conducted by Lawrence Livermore National Laboratory, Los Alamos National Laboratory, Lovelace Respiratory Research Institute, and ADA Technologies, Inc. Design features of the analyzer and preliminary test results are presented.

  18. Sub-micro level monitoring of beryllium ions with a novel beryllium sensor based on 2,6-diphenyl-4-benzo-9-crown-3-pyridine.

    Science.gov (United States)

    Ganjali, Mohammad Reza; Rahimi-Nasrabadi, Mehdi; Maddah, Bozorgmehr; Moghimi, Abolghasem; Faal-Rastegar, Madjid; Borhany, Shahin; Namazian, Mansour

    2004-07-01

    The 2,6-diphenyl-4-benzo-9-crown-3-pyridine (DPCP) was used as an excellent ionophore in construction of a coated graphite poly(vinyl chloride) (PVC)-based membrane sensor. The best performance was obtained with a membrane composition of 30% poly(vinyl chloride), 60% o-nitrophenyloctyl ether (NPOE), 5% 2,6-diphenyl-4-benzo-9-crown-3-pyridine and 5% sodium tetraphenyl borate (TBP). This sensor shows very good selectivity and sensitivity towards beryllium ion over a wide variety of cations, including alkali, alkaline earth, transition and heavy metal ions. The sensor revealed a great enhancement in selectivity coefficients and sensitivity for beryllium, in comparison with the previously reported beryllium electrodes. The electrode exhibits a Nernstian behavior (with slope of 29.6mV per decade) over a very wide concentration range (1.0x10(-7) to 1.0x10(-1)) with a detection limit of 4.0x10(-8)M (360pgml(-1)). It shows relatively fast response time, in whole concentration range (beryllium in mineral ore.

  19. Effect of composition of Al-Si welding wires on welded joint characteristics of copper and aluminum by CMT welding%铝硅焊丝成分对铜铝异种金属CMT焊接接头特征的影响

    Institute of Scientific and Technical Information of China (English)

    孟凡玲; 吕曜晨; 武小娟; 孙焕焕

    2016-01-01

    采用冷金属过渡(CMT)焊对异种金属T2和1060Al进行焊接,选用S301、ER4043、ER4047 3种焊丝作为填充材料,研究在适当工艺参数下,焊丝成分对焊接接头组织、相组成、界面化合物形态及硬度的影响.结果表明:3种焊丝焊接的接头均由焊缝区、结合区、熔合区组成,且靠Cu侧的焊缝结合区均生成了较厚的界面化合物层.结合区的组织主要为(α-Al+ CuAl2)共晶和CuAl2金属间化合物相,当采用含Si量12.0%的ER4047焊接时结合区还析出了块状Si.焊丝中添加Si元素,抑制了靠Cu侧焊缝区界面化合物生长,并改变了化合物形态.同时,界面化合物生成,也导致3种焊缝均在靠Cu侧出现显微硬度的高峰区.%Cold metal transfer (CMT) welding was employed to weld the dissimilar metallic sheets of T2 and 1060 aluminum.S301,ER4043 and ER4047 welding wires were used as filler materials,respectively.The effects of composition of Al-Si welding wires on the characteristics of Cu-Al welded joints obtained by using suitable CMT welding parameters were studied.The results show that the three welded joints are composed of weld zone,bonding zone,fusion zone,and the thick interface compounds are generated at the bonding zone near the copper sheets.The microstructure of the three bonding zones is mainly (α-Al + CuAl2) eutectic and CuAl2 intermetallics.Moreover,the massive Si phases are found at the bonding zones of the welded joint that produced by using ER4047 welding wire with 12.0% Si.These results indicate that Si element in the welding wires can restrain the growth of the interface compounds in the weld near the copper sheet,and the morphology of the compounds also can be changed by Si element as changing their contents in welding wires.The microhardness peak zones are formed in the copper side of the joint interface because of these interface compounds.

  20. Preparation of a sinterable beryllium oxide through decomposition of beryllium hydroxide (1963); Preparation d'un oxyde de beryllium frittable par decomposition de l'hydiloxyde (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Bernier, M. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-07-01

    In the course of the present study, we have attempted to precise the factors which among the ones effective in the course of the preparation of the beryllium hydroxide and oxide and during the sintering have an influence on the final result: the density and homogeneity of the sintered body. Of the several varieties of hydroxides precipitated from a sulfate solution the {beta}-hydroxide only is always contaminated with beryllium sulfate and cannot be purified even by thorough washing. We noticed that those varieties of the hydroxide (gel, {alpha}, {beta}) have different decomposition rates; this behaviour is used to identify and even to dose the different species in ({alpha}, {beta}) mixtures. The various hydroxides transmit to the resulting oxides the shape they had when precipitated. Accordingly the history of the oxide is revealed by its behaviour during its fabrication and sintering. By comparing the results of the sintering operation with the various measurements performed on the oxide powders we are led to the conclusion that an oxide obtained from beryllium hydroxide is sinterable under vacuum if the following conditions are fulfilled: the particle size must lie between 0.1 and 0.2 {mu} and the BeSO{sub 4} content of the powder must be less than 0.25 per cent wt (expressed as SO{sub 3}/BeO). The best fitting is obtained with the oxide issued from an {alpha}-hydroxide precipitated as very small aggregates and with a low sulfur-content. We have observed that this is also the case for the oxide obtained by direct calcination of beryllium sulfate. (author) [French] Au cours de cette etude, nous avons cherche a preciser les facteurs qui, intervenant tout au long de la preparation de l'hydroxyde, puis de l'oxyde de beryllium et enfin du frittage, peuvent avoir une influence sur le resultat final: la densite et l'homogeneite du fritte. Parmi tous les hydroxydes precipites d'une solution de sulfate, seul l'hydroxyde {beta} est toujours

  1. Joint pain

    Science.gov (United States)

    ... or conditions. It may be linked to arthritis , bursitis , and muscle pain . No matter what causes it, ... Autoimmune diseases such as rheumatoid arthritis and lupus Bursitis Chondromalacia patellae Crystals in the joint: Gout (especially ...

  2. Design of the beryllium window for Brookhaven Linac Isotope Producer

    Energy Technology Data Exchange (ETDEWEB)

    Nayak, S. [Brookhaven National Lab. (BNL), Upton, NY (United States); Mapes, M. [Brookhaven National Lab. (BNL), Upton, NY (United States); Raparia, D. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2015-11-01

    In the Brookhaven Linac Isotope Producer (BLIP) beam line, there were two Beryllium (Be) windows with an air gap to separate the high vacuum upstream side from low vacuum downstream side. There had been frequent window failures in the past which affected the machine productivity and increased the radiation dose received by workers due to unplanned maintenance. To improve the window life, design of Be window is reexamined. Detailed structural and thermal simulations are carried out on Be window for different design parameters and loading conditions to come up with better design to improve the window life. The new design removed the air gap and connect the both beam lines with a Be window in-between. The new design has multiple advantages such as 1) reduces the beam energy loss (because of one window with no air gap), 2) reduces air activation due to nuclear radiation and 3) increased the machine reliability as there is no direct pressure load during operation. For quick replacement of this window, an aluminum bellow coupled with load binder was designed. There hasn’t been a single window failure since the new design was implemented in 2012.

  3. Beryllium-induced immune response in C3H mice

    Energy Technology Data Exchange (ETDEWEB)

    Benson, J.M.; Bice, D.E.; Nikula, K.J. [and others

    1995-12-01

    Studies conducted at ITRI over the past several years have investigated whether Beagle dogs, monkeys, and mice are suitable models for human chronic beryllium-induced lung disease (CBD). Recent studies have focused on the histopathological and immunopathological changes occurring in A/J and C3H/HeJ mice acutely exposed by inhalation to Be metal. Lung lesions in both strains of mice included focal lymphocyte aggregates comprised primarily of B lymphocytes and lesser amounts of T-helper lymphocytes and microgranulomas consisting chiefly of macrophages and T-helper lymphocytes. The distribution of proliferating cells within the microgranulomas was similar to the distribution of T-helper cells. These results strongly suggested that A/J and C3H/HeJ mice responded to inhaled Be metal in a fashion similar to humans in terms of pulmonary lesions and the apparent in situ proliferation of T-helper cells. Results of these studies confirm lymphocyte involvement in the pulmonary response to inhaled Be metal.

  4. Is there a sign of new physics in beryllium transitions?

    Science.gov (United States)

    Fornal, Bartosz

    2017-01-01

    A 6.8 σ anomaly in the invariant mass distribution of e+e- pairs produced via internal pair creation in 8 Be nuclear transitions has been reported recently by Krasznahorkay et al. in Phys. Rev. Lett. 116 (2016) 042501. The data can be explained by a 17 MeV vector gauge boson X produced in the transition of an excited beryllium state to the ground state, 8Be* ->8 Be X , followed by the decay X ->e+e- . We find that the gauge boson X can be associated with a new ``protophobic'' fifth force (i.e.with a coupling to protons suppressed compared to its coupling to neutrons) with a characteristic range of 10 fm and milli-charged couplings to first generation quarks and electrons. We show that such a ``protophobic'' gauge boson is consistent with all available experimental constraints and we discuss several ways to embed this new particle into an anomaly-free extension of the Standard Model. One of the most appealing theories of this type is a model with gauged baryon number, in which the new gauge boson kinetically mixes with the photon, and provides a portal to the dark matter sector. Apart from the phenomenological richness of the model, it can also alleviate the current 3.6 σ discrepancy between the predicted and measured values of the muon's anomalous magnetic moment. B.F. acknowledges partial support from DOE Grant DE-SC0009919 and NSF Grant PHY-1316792.

  5. Spectroscopic Study on the Beryllium Abundances of Red Giant Stars

    CERN Document Server

    Takeda, Yoichi

    2014-01-01

    An extensive spectroscopic study was carried out for the beryllium abundances of 200 red giants (mostly of late G and early K type), which were determined from the near-UV Be II 3131.066 line based on high-dispersion spectra obtained by Subaru/HDS, with an aim of investigating the nature of surface Be contents in these evolved giants; e.g., dependence upon stellar parameters, degree of peculiarity along with its origin and build-up timing. We found that Be is considerably deficient (to widely different degree from star to star) in the photosphere of these evolved giants by ~1-3 dex (or more) compared to the initial abundance. While the resulting Be abundances (A(Be)) appear to weakly depend upon T_eff, log g, [Fe/H], M, age, and v_sin i, this may be attributed to the metallicity dependence of A(Be) coupled with the mutual correlation between these stellar parameters, since such tendencies almost disappear in the metallicity-scaled Be abundance ([Be/Fe]). By comparing the Be abundances (as well as their correl...

  6. Beryllium abundance in turn-off stars of NGC 6752

    CERN Document Server

    Pasquini, L; Randich, S; Galli, D; Gratton, R G; Wolff, B; Pasquini, Luca; Bonifacio, Piercarlo; Randich, Sofia; Galli, Daniele; Gratton, Raffaele G.

    2006-01-01

    Aims: To measure the beryllium abundance in two TO stars of the Globular Cluster NGC 6752, one oxygen rich and sodium poor, the other presumably oxygen poor and sodium rich. Be abundances in these stars are used to put on firmer grounds the hypothesis of Be as cosmochronometer and to investigate the formation of Globular Clusters. Method:We present near UV spectra with resolution R$\\sim 45000$ obtained with the UVES spectrograph on the 8.2m VLT Kueyen telescope, analysed with spectrum synthesis based on plane parallel LTE model atmospheres. Results:Be is detected in the O rich star with log(Be/H)=-12.04 $\\pm$0.15, while Be is not detected in the other star for which we obtain the upper limit log(Be/H)$<$-12.2. A large difference in nitrogen abundance (1.6 dex) is found between the two stars. Conclusions:The Be measurement is compatible with what found in field stars with the same [Fe/H] and [O/H]. The 'Be age' of the cluster is found to be 13.3 Gyrs, in excellent agreement with the results from main sequen...

  7. Inelastic Collisions of Positrons with Beryllium and Magnesium Ions

    Science.gov (United States)

    El-Bakry, Salah-Yaseen

    The collision of positrons with beryllium and magnesium positive ions is treated for the first time as a three-channel problem with the assumption that the elastic, ground-positronium and excited-positronium formation channels are open. A one-valence-electron model for the targets, based on the Clementi-Roetti Slater basis functions, as well as an improved coupled-static approach allowing for the polarization of the excited positronium, are used for calculating the partial cross-sections of eight partial waves (corresponding to 0≤ℓ≤7, where ℓ is the total angular momentum of the scattering problem considered). The calculations are carried out, in each case, at 19 values of the incident energy lying above the excited positronium formation threshold (i.e. above 16.42 eV in e+-Be+ scattering and above 13.02 eV in e+-Mg+ scattering). The total elastic cross-sections of e+-Mg+ scattering show a peak around the ionization threshold of Mg+ (at 14.723 eV) but for e+-Be+ scattering, display a peak at 90 eV (remember that the ionization threshold of Be+ is 18.2 eV). Although the resulting total collisional positronium formation cross-sections are smaller than the elastic ones, their relatively large values should draw the attention of experimental and theoretical physicists to the field of positron-ion collisions.

  8. Beryllium-Induced Hypersensitivity: Genetic Susceptibility and Neoantigen Generation.

    Science.gov (United States)

    Fontenot, Andrew P; Falta, Michael T; Kappler, John W; Dai, Shaodong; McKee, Amy S

    2016-01-01

    Chronic beryllium (Be) disease is a granulomatous lung disorder that results from Be exposure in a genetically susceptible host. The disease is characterized by the accumulation of Be-responsive CD4(+) T cells in the lung, and genetic susceptibility is primarily linked to HLA-DPB1 alleles possessing a glutamic acid at position 69 of the β-chain. Recent structural analysis of a Be-specific TCR interacting with a Be-loaded HLA-DP2-peptide complex revealed that Be is coordinated by amino acid residues derived from the HLA-DP2 β-chain and peptide and showed that the TCR does not directly interact with the Be(2+) cation. Rather, the TCR recognizes a modified HLA-DP2-peptide complex with charge and conformational changes. Collectively, these findings provide a structural basis for the development of this occupational lung disease through the ability of Be to induce posttranslational modifications in preexisting HLA-DP2-peptide complexes, resulting in the creation of neoantigens.

  9. Beryllium increases the CD14(dim)CD16+ subset in the lung of chronic beryllium disease.

    Science.gov (United States)

    Li, Li; Hamzeh, Nabeel; Gillespie, May; Elliott, Jill; Wang, Jieru; Gottschall, Eva Brigitte; Mroz, Peggy M; Maier, Lisa A

    2015-01-01

    CD14dimCD16+ and CD14brightCD16+ cells, which compose a minor population of monocytes in human peripheral blood mononuclear cells (PBMC), have been implicated in several inflammatory diseases. The aim of this study was to investigate whether this phenotype was present as a subset of lung infiltrative alveolar macrophages (AMs) in the granulomatous lung disease, chronic beryllium disease (CBD). The monocytes subsets was determined from PBMC cells and bronchoalveolar lavage (BAL) cells from CBD, beryllium sensitized Non-smoker (BeS-NS) and healthy subjects (HS) using flow cytometry. The impact of smoking on the AMs cell phenotype was determined by using BAL cells from BeS smokers (BeS-S). In comparison with the other monocyte subpopulations, CD14dimCD16+ cells were at decreased frequency in PBMCs of both BeS-NS and CBD and showed higher HLA-DR expression, compared to HS. The AMs from CBD and BeS-NS demonstrated a CD14dimCD16+phenotype, while CD14brightCD16+ cells were found at increased frequency in AMs of BeS, compared to HS. Fresh AMs from BeS-NS and CBD demonstrated significantly greater CD16, CD40, CD86 and HLA-DR than HS and BeS-S. The expression of CD16 on AMs from both CBD and BeS-NS was downregulated significantly after 10μM BeSO4 stimulation. The phagocytic activity of AMs decreased after 10μM BeSO4 treatment in both BeS-NS and CBD, although was altered or reduced in HS and BeS-S. These results suggest that Be increases the CD14dimCD16+ subsets in the lung of CBD subjects. We speculate that Be-stimulates the compartmentalization of a more mature CD16+ macrophage phenotype and that in turn these macrophages are a source of Th1 cytokines and chemokines that perpetuate the Be immune response in CBD. The protective effect of cigarette smoking in BeS-S may be due to the low expression of co-stimulatory markers on AMs from smokers as well as the decreased phagocytic function.

  10. Beryllium increases the CD14(dimCD16+ subset in the lung of chronic beryllium disease.

    Directory of Open Access Journals (Sweden)

    Li Li

    Full Text Available CD14dimCD16+ and CD14brightCD16+ cells, which compose a minor population of monocytes in human peripheral blood mononuclear cells (PBMC, have been implicated in several inflammatory diseases. The aim of this study was to investigate whether this phenotype was present as a subset of lung infiltrative alveolar macrophages (AMs in the granulomatous lung disease, chronic beryllium disease (CBD. The monocytes subsets was determined from PBMC cells and bronchoalveolar lavage (BAL cells from CBD, beryllium sensitized Non-smoker (BeS-NS and healthy subjects (HS using flow cytometry. The impact of smoking on the AMs cell phenotype was determined by using BAL cells from BeS smokers (BeS-S. In comparison with the other monocyte subpopulations, CD14dimCD16+ cells were at decreased frequency in PBMCs of both BeS-NS and CBD and showed higher HLA-DR expression, compared to HS. The AMs from CBD and BeS-NS demonstrated a CD14dimCD16+phenotype, while CD14brightCD16+ cells were found at increased frequency in AMs of BeS, compared to HS. Fresh AMs from BeS-NS and CBD demonstrated significantly greater CD16, CD40, CD86 and HLA-DR than HS and BeS-S. The expression of CD16 on AMs from both CBD and BeS-NS was downregulated significantly after 10μM BeSO4 stimulation. The phagocytic activity of AMs decreased after 10μM BeSO4 treatment in both BeS-NS and CBD, although was altered or reduced in HS and BeS-S. These results suggest that Be increases the CD14dimCD16+ subsets in the lung of CBD subjects. We speculate that Be-stimulates the compartmentalization of a more mature CD16+ macrophage phenotype and that in turn these macrophages are a source of Th1 cytokines and chemokines that perpetuate the Be immune response in CBD. The protective effect of cigarette smoking in BeS-S may be due to the low expression of co-stimulatory markers on AMs from smokers as well as the decreased phagocytic function.

  11. Accelerator mass spectrometry detection of beryllium ions in the antigen processing and presentation pathway.

    Science.gov (United States)

    Tooker, Brian C; Brindley, Stephen M; Chiarappa-Zucca, Marina L; Turteltaub, Kenneth W; Newman, Lee S

    2015-01-01

    Exposure to small amounts of beryllium (Be) can result in beryllium sensitization and progression to Chronic Beryllium Disease (CBD). In CBD, beryllium is presented to Be-responsive T-cells by professional antigen-presenting cells (APC). This presentation drives T-cell proliferation and pro-inflammatory cytokine (IL-2, TNFα, and IFNγ) production and leads to granuloma formation. The mechanism by which beryllium enters an APC and is processed to become part of the beryllium antigen complex has not yet been elucidated. Developing techniques for beryllium detection with enough sensitivity has presented a barrier to further investigation. The objective of this study was to demonstrate that Accelerator Mass Spectrometry (AMS) is sensitive enough to quantify the amount of beryllium presented by APC to stimulate Be-responsive T-cells. To achieve this goal, APC - which may or may not stimulate Be-responsive T-cells - were cultured with Be-ferritin. Then, by utilizing AMS, the amount of beryllium processed for presentation was determined. Further, IFNγ intracellular cytokine assays were performed to demonstrate that Be-ferritin (at levels used in the experiments) could stimulate Be-responsive T-cells when presented by an APC of the correct HLA type (HLA-DP0201). The results indicated that Be-responsive T-cells expressed IFNγ only when APC with the correct HLA type were able to process Be for presentation. Utilizing AMS, it was determined that APC with HLA-DP0201 had membrane fractions containing 0.17-0.59 ng Be and APC with HLA-DP0401 had membrane fractions bearing 0.40-0.45 ng Be. However, HLA-DP0401 APC had 20-times more Be associated with the whole cells (57.68-61.12 ng) than HLA-DP0201 APC (0.90-3.49 ng). As these findings demonstrate, AMS detection of picogram levels of Be processed by APC is possible. Further, regardless of form, Be requires processing by APC to successfully stimulate Be-responsive T-cells to generate IFNγ.

  12. Migration of Beryllium via Multiple Exposure Pathways among Work Processes in Four Different Facilities.

    Science.gov (United States)

    Armstrong, Jenna L; Day, Gregory A; Park, Ji Young; Stefaniak, Aleksandr B; Stanton, Marcia L; Deubner, David C; Kent, Michael S; Schuler, Christine R; Virji, M Abbas

    2014-01-01

    Inhalation of beryllium is associated with the development of sensitization; however, dermal exposure may also be important. The primary aim of this study was to elucidate relationships among exposure pathways in four different manufacturing and finishing facilities. Secondary aims were to identify jobs with increased levels of beryllium in air, on skin, and on surfaces; identify potential discrepancies in exposure pathways, and determine if these are related to jobs with previously identified risk. Beryllium was measured in air, on cotton gloves, and on work surfaces. Summary statistics were calculated and correlations among all three measurement types were examined at the facility and job level. Exposure ranking strategies were used to identify jobs with higher exposures. The highest air, glove, and surface measurements were observed in beryllium metal production and beryllium oxide ceramics manufacturing jobs that involved hot processes and handling powders. Two finishing and distribution facilities that handle solid alloy products had lower exposures than the primary production facilities, and there were differences observed among jobs. For all facilities combined, strong correlations were found between air-surface (rp ≥ 0.77), glove-surface (rp ≥ 0.76), and air-glove measurements (rp ≥ 0.69). In jobs where higher risk of beryllium sensitization or disease has been reported, exposure levels for all three measurement types were higher than in jobs with lower risk, though they were not the highest. Some jobs with low air concentrations had higher levels of beryllium on glove and surface wipe samples, suggesting a need to further evaluate the causes of the discrepant levels. Although such correlations provide insight on where beryllium is located throughout the workplace, they cannot identify the direction of the pathways between air, surface, or skin. Ranking strategies helped to identify jobs with the highest combined air, glove, and/or surface exposures

  13. X-ray drive of beryllium capsule implosions at the National Ignition Facility

    Science.gov (United States)

    Wilson, D. C.; Yi, S. A.; Simakov, A. N.; Kline, J. L.; Kyrala, G. A.; Dewald, E. L.; Tommasini, R.; Ralph, J. E.; Olson, R. E.; Strozzi, D. J.; Celliers, P. M.; Schneider, M. B.; MacPhee, A. G.; Zylstra, A. B.; Callahan, D. A.; Hurricane, O. A.; Milovich, J. L.; Hinkel, D. E.; Rygg, J. R.; Rinderknecht, H. G.; Sio, H.; Perry, T. S.; Batha, S.

    2016-05-01

    National Ignition Facility experiments with beryllium capsules have followed a path begun with “high-foot” plastic capsule implosions. Three shock timing keyhole targets, one symmetry capsule, a streaked backlit capsule, and a 2D backlit capsule were fielded before the DT layered shot. After backscatter subtraction, laser drive degradation is needed to match observed X-ray drives. VISAR measurements determined drive degradation for the picket, trough, and second pulse. Time dependence of the total Dante flux reflects degradation of the of the third laser pulse. The same drive degradation that matches Dante data for three beryllium shots matches Dante and bangtimes for plastic shots N130501 and N130812. In the picket of both Be and CH hohlraums, calculations over-estimate the x-ray flux > 1.8 keV by ∼100X, while calculating the total flux correctly. In beryllium calculations these X-rays cause an early expansion of the beryllium/fuel interface at ∼3 km/s. VISAR measurements gave only ∼0.3 km/s. The X-ray drive on the Be DT capsule was further degraded by an unplanned decrease of 9% in the total picket flux. This small change caused the fuel adiabat to rise from 1.8 to 2.3. The first NIF beryllium DT implosion achieved 29% of calculated yield, compared to CH capsules with 68% and 21%.

  14. Inherent structure features of beryllium and their influence on the performance polycrystalline metal under different conditions

    Energy Technology Data Exchange (ETDEWEB)

    Khomutov, A.M.; Mikhailov, V.S.; Pronin, V.N.; Pakhomov, Ya.D. [State Scientific Center of Russian Federation `A.A. Bochvar All-Russia Research Inst. of Inorganic Materials (VNIINM)`, Moscow (Russian Federation)

    1998-01-01

    The anisotropy of physical properties of beryllium single crystals resulting from covalent bonds in crystal lattice leads to significant residual thermal microstresses (RTM) in the polycrystalline metal. It is demonstrated experimentally that there is a simple linear dependence between the magnitude of RTM and the ultimate tensile strength. The factors controlling RTM are analysed and in the framework of powder metallurgy process the technological methods of producing beryllium with the needed properties are recommended. Primarily it is necessary to control the quantity and extent of dispersity of intergranular oxide inclusions and mean grain size in combination with the high degree of macro- and microhomogenity of the structure. The requirements to beryllium microstructure for different operating conditions including neutron fluxes and transient temperature fields are formulated. In the framework of the concept under development one can explain formerly not fully understandable effects, which are characteristic of polycrystalline beryllium such as unexpected Petch-Stro curve, the role of twinning etc., and predict new ones. In particular, it can be possible to expect the growth of ductility of high strength beryllium grades as neutron irradiated. (author)

  15. Study the effect of beryllium reflector poisoning on the Syrian MNSR.

    Science.gov (United States)

    Omar, H; Ghazi, N; Haddad, Kh; Ezzuddin, H

    2012-06-01

    Neutron interactions with beryllium lead to formation of (3)H and strong neutron absorbers (3)He and (6)Li in the reflector (so called beryllium poisoning). After the reactor shutdown, the concentration of (3)He increases in time due to tritium decay. This paper illustrates the impact of poisoning accumulation in the beryllium reflectors on reactivity for the Syrian MNSR research reactor. The prediction of (6)Li and (3)He poison concentrations, initiated by the 9Be(n,α) reaction, in the beryllium reflectors of the MNSR was also presented. The results were based on MCNP Monte Carlo calculations and solutions to the differential equations which describe the time dependent poison concentrations as a function of reactor operation time and shutdown periods. The whole reactor history was taken into account to predict reliable values of parasitic isotope concentrations. It was found that the (3)He and (6)Li accumulations in the beryllium reflectors during the actual working history decreased the excess reactivity by about 28%. While, the effect became more significant at the reactor life's end and the reactor became subcritical after 25,000 h operation. The results contained in this paper could be used in assess the safety analysis of the MNSR reactor.

  16. Search for chronic beryllium disease among sarcoidosis patients in Ontario, Canada.

    Science.gov (United States)

    Ribeiro, Marcos; Fritscher, Leandro G; Al-Musaed, Ahmed M; Balter, Meyer S; Hoffstein, Victor; Mazer, Bruce D; Maier, Lisa A; Liss, Gary M; Tarlo, Susan M

    2011-06-01

    Chronic beryllium disease (CBD) is clinically similar to other granulomatous diseases such as sarcoidosis. It is often misdiagnosed if a thorough occupational history is not taken. When appropriate, a beryllium lymphocyte proliferation tests (BeLPT) need to be performed. We aimed to search for CBD among currently diagnosed pulmonary sarcoidosis patients and to identify the occupations and exposures in Ontario leading to CBD. Questionnaire items included work history and details of possible exposure to beryllium. Participants who provided a history of previous work with metals underwent BeLPTs and an ELISPOT on the basis of having a higher pretest probability of CBD. Among 121 sarcoid patients enrolled, 87 (72%) reported no known previous metal dust or fume exposure, while 34 (28%) had metal exposure, including 17 (14%) with beryllium exposure at work or home. However, none of these 34 who underwent testing had positive test results. Self-reported exposure to beryllium or metals was relatively common in these patients with clinical sarcoidosis, but CBD was not confirmed using blood assays in this population.

  17. Occupational exposure to beryllium and cancer risk: a review of the epidemiologic evidence.

    Science.gov (United States)

    Boffetta, Paolo; Fryzek, Jon P; Mandel, Jack S

    2012-02-01

    There is controversy on whether occupational exposure to beryllium causes lung cancer. We conducted a systematic review of epidemiologic studies on cancer among workers exposed to beryllium, including a study of seven U.S. production plants which has been recently updated, a study of patients with beryllium disease (largely overlapping with the former study) and several smaller studies. A small excess mortality from lung cancer was detected in the large cohort, which was partially explained by confounding by tobacco smoking and urban residence. Other potential confounders have not been addressed. The excess mortality was mainly among workers employed (often for a short duration) in the early phase of the manufacturing industry. There was no relation with duration of employment or cumulative exposure, whereas average and maximum exposure were associated with lung cancer risk. The use of lagged exposure variables resulted in associations with lung cancer risk; however, these associations were due to confounding by year of birth and year of hire. The studies of beryllium disease patients do not provide independent evidence and the results from other studies do not support the hypothesis of an increased risk of lung cancer or any other cancer. Overall, the available evidence does not support a conclusion that a causal association has been established between occupational exposure to beryllium and the risk of cancer.

  18. Long-term follow-up of beryllium sensitized workers from a single employer

    Directory of Open Access Journals (Sweden)

    Curtis Anne M

    2010-01-01

    Full Text Available Abstract Background Up to 12% of beryllium-exposed American workers would test positive on beryllium lymphocyte proliferation test (BeLPT screening, but the implications of sensitization remain uncertain. Methods Seventy two current and former employees of a beryllium manufacturer, including 22 with pathologic changes of chronic beryllium disease (CBD, and 50 without, with a confirmed positive test were followed-up for 7.4 +/-3.1 years. Results Beyond predicted effects of aging, flow rates and lung volumes changed little from baseline, while DLCO dropped 17.4% of predicted on average. Despite this group decline, only 8 subjects (11.1% demonstrated physiologic or radiologic abnormalities typical of CBD. Other than baseline status, no clinical or laboratory feature distinguished those who clinically manifested CBD at follow-up from those who did not. Conclusions The clinical outlook remains favorable for beryllium-sensitized individuals over the first 5-12 years. However, declines in DLCO may presage further and more serious clinical manifestations in the future. These conclusions are tempered by the possibility of selection bias and other study limitations.

  19. YF-12 Lockalloy ventral fin program, volume 1. [design analysis, fabrication, and manufacturing of aircraft structures using aluminum and beryllium alloys for the lockheed YF-12 aircraft

    Science.gov (United States)

    Duba, R. J.; Haramis, A. C.; Marks, R. F.; Payne, L.; Sessing, R. C.

    1976-01-01

    Results are presented of the YF-12 Lockalloy Ventral Fin Program which was carried out by Lockheed Aircraft Corporation - Advanced Development Projects for the joint NASA/USAF YF-12 Project. The primary purpose of the program was to redesign and fabricate the ventral fin of the YF-12 research airplane (to reduce flutter) using Lockalloy, and alloy of beryllium and aluminum, as a major structural material. A secondary purpose, was to make a material characterization study (thermodynamic properties, corrosion; fatigue tests, mechanical properties) of Lockalloy to validate the design of the ventral fin and expand the existing data base on this material. All significant information pertinent to the design and fabrication of the ventral fin is covered. Emphasis throughout is given to Lockalloy fabrication and machining techniques and attendant personnel safety precautions. Costs are also examined. Photographs of tested alloy specimens are shown along with the test equipment used.

  20. Post irradiation characterization of beryllium and beryllides after high temperature irradiation up to 3000 appm helium production in HIDOBE-01

    Energy Technology Data Exchange (ETDEWEB)

    Fedorov, A.V., E-mail: fedorov@nrg.eu [Nuclear Research and Consultancy Group, Westerduinweg 3, Postbus 25, Petten, 1755 ZG (Netherlands); Til, S. van; Stijkel, M.P. [Nuclear Research and Consultancy Group, Westerduinweg 3, Postbus 25, Petten, 1755 ZG (Netherlands); Nakamichi, M. [Japan Atomic Energy Agency, Rokkasho (Japan); Zmitko, M. [The European Joint Undertaking for ITER and the Development of Fusion Energy, c/ Josep Pla, n° 2, Torres Diagonal Litoral, Edificio B3, Barcelona 08019 (Spain)

    2016-01-15

    Titanium beryllides are considered as advanced candidate material for neutron multiplier for the helium cooled pebble bed (HCPB) and/or the water cooled ceramic breeder (WCCB) breeder blankets. In the HIDOBE-01 (HIgh DOse irradiation of BEryllium) experiment, beryllium and beryllide pellets with 5 at% and 7 at% Ti are irradiated at four different target temperatures (T{sub irr}): 425 °C, 525 °C, 650 °C and 750 °C up to the dose corresponding to 3000 appm He production in beryllium. The pellets were supplied by JAEA. During post irradiation examinations the critical properties of volumetric swelling and tritium retention were studied. Both titanium beryllide grades show significantly less swelling than the beryllium grade, with the difference increasing with the irradiation temperature. The irradiation induced swelling was studied by using direct dimensions. Both beryllide grades showed much less swelling as compare to the reference beryllium grade. Densities of the grades were studied by Archimedean immersion and by He-pycnometry, giving indications of porosity formation. While both beryllide grades show no significant reduction in density at all irradiation temperatures, the beryllium density falls steeply at higher T{sub irr}. Finally, the tritium release and retention were studied by temperature programmed desorption (TPD). Beryllium shows the same strong tritium retention as earlier observed in studies on beryllium pebbles, while the tritium inventory of the beryllides is significantly less, already at the lowest T{sub irr} of 425 °C.

  1. Beryllium chloride-induced oxidative DNA damage and alteration in the expression patterns of DNA repair-related genes.

    Science.gov (United States)

    Attia, Sabry M; Harisa, Gamaleldin I; Hassan, Memy H; Bakheet, Saleh A

    2013-09-01

    Beryllium metal has physical properties that make its use essential for very specific applications, such as medical diagnostics, nuclear/fusion reactors and aerospace applications. Because of the widespread human exposure to beryllium metals and the discrepancy of the genotoxic results in the reported literature, detail assessments of the genetic damage of beryllium are warranted. Mice exposed to beryllium chloride at an oral dose of 23mg/kg for seven consecutive days exhibited a significant increase in the level of DNA-strand breaking and micronuclei formation as detected by a bone marrow standard comet assay and micronucleus test. Whereas slight beryllium chloride-induced oxidative DNA damage was detected following formamidopyrimidine DNA glycosylase digestion, digestion with endonuclease III resulted in considerable increases in oxidative DNA damage after the 11.5 and 23mg/kg/day treatment as detected by enzyme-modified comet assays. Increased 8-hydroxydeoxyguanosine was also directly correlated with increased bone marrow micronuclei formation and DNA strand breaks, which further confirm the involvement of oxidative stress in the induction of bone marrow genetic damage after exposure to beryllium chloride. Gene expression analysis on the bone marrow cells from beryllium chloride-exposed mice showed significant alterations in genes associated with DNA damage repair. Therefore, beryllium chloride may cause genetic damage to bone marrow cells due to the oxidative stress and the induced unrepaired DNA damage is probably due to the down-regulation in the expression of DNA repair genes, which may lead to genotoxicity and eventually cause carcinogenicity.

  2. Laser micro welding of copper and aluminum

    Science.gov (United States)

    Mys, Ihor; Schmidt, Michael

    2006-02-01

    Aluminum combines comparably good thermal and electrical properties with a low price and a low material weight. These properties make aluminum a promising alternative to copper for a large number of electronic applications, especially when manufacturing high volume components. However, a main obstacle for a wide use of this material is the lack of a reliable joining process for the interconnection of copper and aluminum. The reasons for this are a large misalignment in the physical properties and even more a poor metallurgical affinity of both materials that cause high crack sensitivity and the formation of brittle intermetallic phases during fusion welding. This paper presents investigations on laser micro welding of copper and aluminum with the objective to eliminate brittle intermetallic phases in the welding structure. For these purposes a combination of spot welding, a proper beam offset and special filler material are applied. The effect of silver, nickel and tin filler materials in the form of thin foils and coatings in a thickness range 3-100 μm has been investigated. Use of silver and tin filler materials yields to a considerable improvement of the static and dynamic mechanical stability of welded joints. The analysis of the weld microstructure shows that an application even of small amounts of suitable filler materials helps to avoid critical, very brittle intermetallic phases on the interface between copper and solidified melt in the welded joints.

  3. Yunnan Starts its Largest Copper Mining and Dressing Project

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    <正> Along with the recent establishment of DiqingMining Development Co.,the largest coppermining and dressing projeject at Yangla,DeqinCounty in Yunnan province started construc-tion.This project is invested by Yunnan Cop-per Group Corp.with RMB10 million yuan forthe mine’s propecting fight and over RMB30million yuan for risk capital.After a year’swork,the copper mine at Yangla is ready forlarge scale development.Yangla Copper Mineis located at the joint area of Yunnan,Sichuan

  4. [Copper pathology (author's transl)].

    Science.gov (United States)

    Mallet, B; Romette, J; Di Costanzo, J D

    1982-01-30

    Copper is an essential dietary component, being the coenzyme of many enzymes with oxidase activity, e.g. ceruloplasmin, superoxide dismutase, monoamine oxidase, etc. The metabolism of copper is complex and imperfectly known. Active transport of copper through the intestinal epithelial cells involves metallothionein, a protein rich in sulfhydryl groups which also binds the copper in excess and probably prevents absorption in toxic amounts. In hepatocytes a metallothionein facilitates absorption by a similar mechanism and regulates copper distribution in the liver: incorporation in an apoceruloplasmin, storage and synthesis of copper-dependent enzymes. Metallothioneins and ceruloplasmin are essential to adequate copper homeostasis. Apart from genetic disorders, diseases involving copper usually result from hypercupraemia of varied origin. Wilson's disease and Menkes' disease, although clinically and pathogenetically different, are both marked by low ceruloplasmin and copper serum levels. The excessive liver retention of copper in Wilson's disease might be due to increased avidity of hepatic metallothioneins for copper and decreased biliary excretion through lysosomal dysfunction. Menkes' disease might be due to low avidity of intestinal and hepatic metallothioneins for copper. The basic biochemical defect responsible for these two hereditary conditions has not yet been fully elucidated.

  5. [Copper IUDs (author's transl)].

    Science.gov (United States)

    Thiery, M

    1983-10-01

    Following initial development of the Grafenberg ring in the 1920's, IUDs fell into disuse until the late 1950s, when plastic devices inserted using new technology began to gain worldwide acceptance. Further research indicated that copper had a significant antifertility effect which increased with increasing surface area, and several copper IUDs were developed and adapted, including the Copper T 200, the Copper T 220C, and the Copper T 380 A, probably the most effective yet. The Gravigard and Multiload are 2 other copper devices developed according to somewhat different principles. Copper devices are widely used not so much because of their great effectiveness as because of their suitability for nulliparous patients and their ease of insertion, which minimizes risk of uterine perforation. Records of 2584 women using Copper IUDs for 7190 women-years and 956 women using devices without copper for 6059 women-years suggest that the copper devices were associated with greater effectiveness and fewer removals for complications. Research suggests that the advantages of copper IUDs become more significant with increased duration of use. Contraindications to copper devices include allergy to copper and hepatolenticular degeneration. No carcinogenic or teratogenic effect of copper devices has been found, but further studies are needed to rule out other undesirable effects. Significant modifications of copper devices in recent years have been developed to increase their effectiveness, prolong their duration of usefulness, facilitate insertion and permit insertion during abortion or delivery. The upper limit of the surface area of copper associated with increased effectiveness appears to be between 200-300 sq mm, and at some point increases in copper exposure may provoke expulsion of the IUD. The duration of fertility inhibition of copper IUDs is usually estimated at 2-3 years, but recent research indicates that it may be 6-8 years, and some devices may retain copper surface

  6. Structures and formation mechanisms of aquo/hydroxo oligomeric beryllium in aqueous solution: a density functional theory study.

    Science.gov (United States)

    Jin, Xiaoyan; Liao, Rongbao; Wu, Hai; Huang, Zhengjie; Zhang, Hong

    2015-09-01

    The structures and formation mechanisms of a wide variety of aquo/hydroxo oligomeric beryllium clusters were investigated using density functional theory. The structural parameters of beryllium clusters were found to vary regularly with the stepwise substitution of bound water molecules in the inner coordination sphere by hydroxyl groups. According to the Gibbs free energies deduced from SMD solvation model computations, unhydrolyzed oligomeric beryllium species are the most favorable products of polymerization, independent of the degrees of hydrolysis of the reactants. Simulation of the formation processes of oligomeric beryllium showed that polymerization, in essence, involves the nucleophilic attack of a terminal hydroxyl group in one BeO4 tetrahedron on the beryllium center in another BeO4 tetrahedron, leading to the bridging of two BeO4 tetrahedrons by a hydroxyl group.

  7. Examination of Beryllium Under Intense High Energy Proton Beam at CERN's HiRadMat Facility

    CERN Document Server

    Ammigan, K; Hurh, P; Zwaska, R; Atherton, A; Caretta, O; Davenne, t; Densham, C; Fitton, M; Loveridge, P; O'Dell, J; Roberts, S; Kuksenko, v; Butcher, M; Calviani, M; Guinchard, M; Losito, R

    2015-01-01

    Beryllium is extensively used in various accelerator beam lines and target facilities as material for beam win- dows, and to a lesser extent, as secondary particle produc- tion targets. With increasing beam intensities of future ac- celerator facilities, it is critical to understand the response of beryllium under extreme conditions to avoid compro- mising particle production efficiency by limiting beam pa- rameters. As a result, the planned experiment at CERN’s HiRadMat facility will take advantage of the test facility’s tunable high intensity proton beam to probe and investigate the damage mechanisms of several grades of beryllium. The test matrix will consist of multiple arrays of thin discs of varying thicknesses as well as cylinders, each exposed to increasing beam intensities. Online instrumentations will acquire real time temperature, strain, and vibration data of the cylinders, while Post-Irradiation-Examination (PIE) of the discs will exploit advanced microstructural characteri- zation and imagin...

  8. Time-lapse cinematographic analysis of beryllium--lung fibroblast interactions.

    Science.gov (United States)

    Absher, M; Sylwester, D; Hart, B A

    1983-02-01

    The proliferative response to beryllium chloride of cells in a population of human lung fibroblasts was quantitatively assessed using time-lapse cinematography. A dose of 0.02 microgram Be/ml, known to decrease the growth rate of fibroblasts, affects an estimated 75% of the cells in the population, increasing their interdivision time (IDT) by approximately 5 hr. The differences in mean 1n(IDT) between treated and control cells were essentially constant for comparable culture sizes ranging from 25 to 250 cells. There was no correlation between mother and daughter cell IDTs in control or treated culture at any culture size. IDTs of sister pairs were highly correlated in control cultures at selected culture sizes while sister pair IDTs of treated cultures were not. The data suggest that while beryllium alters the IDT of fibroblasts, an effect not related to culture size, any given cell affected by beryllium does not impart effects of the mineral to its progeny.

  9. Examination of Beryllium Under Intense High Energy Proton Beam at CERN's HiRadMat Facility

    CERN Document Server

    Ammigan, K.; Hurh, P.; Zwaska, R.; Atherton, A.; Caretta, O.; Davenne,T.; Densham, C.; Fitton, M.; Loveridge, P.; O'Dell, J.; Roberts, S.; Kuksenko, V.; Butcher, M.; Calviani, M.; Guinchard, M.; Losito, R.

    2017-01-01

    Beryllium is extensively used in various accelerator beam lines and target facilities as material for beam win- dows, and to a lesser extent, as secondary particle produc- tion targets. With increasing beam intensities of future ac- celerator facilities, it is critical to understand the response of beryllium under extreme conditions to avoid compro- mising particle production efficiency by limiting beam pa- rameters. As a result, the planned experiment at CERN’s HiRadMat facility will take advantage of the test facility’s tunable high intensity proton beam to probe and investigate the damage mechanisms of several grades of beryllium. The test matrix will consist of multiple arrays of thin discs of varying thicknesses as well as cylinders, each exposed to increasing beam intensities. Online instrumentations will acquire real time temperature, strain, and vibration data of the cylinders, while Post-Irradiation-Examination (PIE) of the discs will exploit advanced microstructural characteri- zation and imagin...

  10. A role for cell adhesion in beryllium-mediated lung disease

    Energy Technology Data Exchange (ETDEWEB)

    Hong-geller, Elizabeth [Los Alamos National Laboratory

    2008-01-01

    Chronic beryllium disease (CBD) is a debilitating lung disorder in which exposure to the lightweight metal beryllium (Be) causes the accumulation of beryllium-specific CD4+ T cells in the lung and formation of noncaseating pulmonary granulomas. Treatment for CBD patients who exhibit progressive pulmonary decline is limited to systemic corticosteroids, which suppress the severe host inflammatory response. Studies in the past several years have begun to highlight cell-cell adhesion interactions in the development of Be hypersensitivity and CBD. In particular, the high binding affinity between intercellular adhesion molecule 1 (I-CAM1) on lung epithelial cells and the {beta}{sub 2} integrin LFA-1 on migrating lymphocytes and macrophages regulates the concerted rolling of immune cells to sites of inflammation in the lung. In this review, we discuss the evidence that implicates cell adhesion processes in onset of Be disease and the potential of cell adhesion as an intervention point for development of novel therapies.

  11. Effect of beryllium nitrate on early and late pregnancy in rats

    Energy Technology Data Exchange (ETDEWEB)

    Mathur, R.; Sharma, S.; Mathur, S.; Prakash, A.O.

    1987-01-01

    Beryllium is widely used in fatigue-resistant alloys, nuclear reactors, space device, missiles parts, electronics and other specialized purposes. Workers both in industries and mines are constantly exposed through inhalation or direct skin contact. A number of investigations have been made in different laboratories in relation to its toxicological effects in laboratory animals and humans. The lethal dose (LD/sub 50/) of beryllium nitrate through intravenous route in rats has been reported from our laboratory to be 3.16 mg/kg body weight. But not much is known about its effects on reproductive physiology. The present communication deals with the effect of beryllium nitrate on early and late pregnancy in the albino rats.

  12. Equation of State Determination from Quasi-Isentropic Compression of Solid Beryllium Liners on Z

    Science.gov (United States)

    Martin, Matthew; Lemke, Raymond; McBride, Ryan; Knudson, Marcus; Davis, Jean-Paul

    2010-11-01

    We investigate the beryllium equation of state through constraining magneto-hydrodynamic and magneto-solid dynamic simulation with experimentally determined density profiles of a compressed beryllium cylindrical liner. Experiments utilizing pulse shaping techniques on Z have achieved quasi-isentropic compression of cylindrical beryllium liners to approximately 3 Megabars, and simulation results suggest that a large fraction of the liner remains in the solid phase through peak pressure for a 20 MA current pulse on Z. This opens up the possibility of extending the range of pressures we can explore with magnetic drive by utilizing cylindrical convergence. However, the cylindrical geometry limits the usefulness of diagnostics commonly applied to planar equation of state measurements on pulsed power machines and requires the development of new methods to unfold isentropes from the experimental data.

  13. A mortality study of workers exposed to insoluble forms of beryllium.

    Science.gov (United States)

    Boffetta, Paolo; Fordyce, Tiffani; Mandel, Jack S

    2014-11-01

    This study investigated lung cancer and other diseases related to insoluble beryllium compounds. A cohort of 4950 workers from four US insoluble beryllium manufacturing facilities were followed through 2009. Expected deaths were calculated using local and national rates. On the basis of local rates, all-cause mortality was significantly reduced. Mortality from lung cancer (standardized mortality ratio 96.0; 95% confidence interval 80.0, 114.3) and from nonmalignant respiratory diseases was also reduced. There were no significant trends for either cause of death according to duration of employment or time since first employment. Uterine cancer among women was the only cause of death with a significantly increased standardized mortality ratio. Five of the seven women worked in office jobs. This study confirmed the lack of an increase in mortality from lung cancer and nonmalignant respiratory diseases related to insoluble beryllium compounds.

  14. Oxide segregation and melting behavior of transient heat load exposed beryllium

    Science.gov (United States)

    Spilker, B.; Linke, J.; Pintsuk, G.; Wirtz, M.

    2016-10-01

    In the experimental fusion reactor ITER, beryllium will be applied as first wall armor material. However, the ITER-like wall project at JET already experienced that the relatively low melting temperature of beryllium can easily be exceeded during plasma operation. Therefore, a detailed study was carried out on S-65 beryllium under various transient, ITER-relevant heat loads that were simulated in the electron beam facility JUDITH 1. Hereby, the absorbed power densities were in the range of 0.15-1.0 GW m-2 in combination with pulse durations of 1-10 ms and pulse numbers of 1-1000. In metallographic cross sections, the emergence of a transition region in a depth of ~70-120 µm was revealed. This transition region was characterized by a strong segregation of oxygen at the grain boundaries, determined with energy dispersive x-ray spectroscopy element mappings. The oxide segregation strongly depended on the maximum temperature reached at the end of the transient heat pulse in combination with the pulse duration. A threshold for this process was found at 936 °C for a pulse duration of 10 ms. Further transient heat pulses applied to specimens that had already formed this transition region resulted in the overheating and melting of the material. The latter occurred between the surface and the transition region and was associated with a strong decrease of the thermal conductivity due to the weakly bound grains across the transition region. Additionally, the transition region caused a partial separation of the melt layer from the bulk material, which could ultimately result in a full detachment of the solidified beryllium layers from the bulk armor. Furthermore, solidified beryllium filaments evolved in several locations of the loaded area and are related to the thermally induced crack formation. However, these filaments are not expected to account for an increase of the beryllium net erosion.

  15. Tibet Mineral Development Teams up with Jinchuan Group to Develop Nimu Copper

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    <正>Tibet Mineral Development decided to sign a cooperation framework agreement with Jinchuan Group Co.,Ltd.,to assign a 25% stake in Nimu Copper Development Co.,Ltd. to Jinchuan Group or its subsidiary,and jointly develop Nimu Copper.

  16. Retention and release mechanisms of deuterium implanted into beryllium

    Science.gov (United States)

    Oberkofler, M.; Reinelt, M.; Linsmeier, Ch.

    2011-06-01

    The fraction of deuterium (D) that is retained upon irradiation of beryllium (Be) as well as the temperatures at which implanted D is released are of importance for the international fusion experiment ITER, where Be will be used as an armor material. The influence of single parameters on retention and release is investigated in laboratory experiments performed under well defined conditions with the aim to identify dominant underlying mechanisms and thus be able to predict the behavior of the Be wall in ITER. Recent progress in the quantification of retained fractions and release temperatures as well as in the understanding of the governing mechanisms is presented. The retained fraction upon implantation of D at 1 keV into Be(1 1 2¯ 0) to fluences far below the saturation threshold of 10 21 m -2 is almost 95%, the remaining 5% being attributed to reflection at the surface. At these low fluences, no dependence of the retained fractions on implantation energy is observed. At fluences of the order of 10 21 m -2 and higher, saturation of the irradiated material affects the retention, leading to lower retained fractions. Furthermore, at these fluences the retained fractions decrease with decreasing implantation energies. Differences in the retained fractions from implanted Be(1 1 2¯ 0) and polycrystalline Be are explained by anisotropic diffusion of interstitials during implantation, leading to an amount of surviving D-trap complexes that depends on surface-orientation. Temperature-programmed desorption (TPD) spectra are recorded after implantation of fluences of the order of 10 19 m -2 at various energies and simulated by means of a newly developed code based on coupled reaction-diffusion systems (CRDS). The asymmetric shape of the TPD peaks is reproduced by introducing a local D accumulation process into the model.

  17. Tritium and helium retention and release from irradiated beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Anderl, R.A.; Longhurst, G.R.; Oates, M.A.; Pawelko, R.J. [Idaho National Engineering and Environmental Lab., Idaho Falls, ID (United States)

    1998-01-01

    This paper reports the results of an experimental effort to anneal irradiated beryllium specimens and characterize them for steam-chemical reactivity experiments. Fully-dense, consolidated powder metallurgy Be cylinders, irradiated in the EBR-II to a fast neutron (>0.1 MeV) fluence of {approx}6 x 10{sup 22} n/cm{sup 2}, were annealed at temperatures from 450degC to 1200degC. The releases of tritium and helium were measured during the heat-up phase and during the high-temperature anneals. These experiments revealed that, at 600degC and below, there was insignificant gas release. Tritium release at 700degC exhibited a delayed increase in the release rate, while the specimen was at 700degC. For anneal temperatures of 800degC and higher, tritium and helium release was concurrent and the release behavior was characterized by gas-burst peaks. Essentially all of the tritium and helium was released at temperatures of 1000degC and higher, whereas about 1/10 of the tritium was released during the anneals at 700degC and 800degC. Measurements were made to determine the bulk density, porosity and specific surface area for each specimen before and after annealing. These measurements indicated that annealing caused the irradiated Be to swell, by as much as 14% at 700degC and 56% at 1200degC. Kr gas adsorption measurements for samples annealed at 1000degC and 1200degC determined specific surface areas between 0.04 m{sup 2}/g and 0.1 m{sup 2}/g for these annealed specimens. The tritium and helium gas release measurements and the specific surface area measurements indicated that annealing of irradiated Be caused a porosity network to evolve and become surface-connected to relieve internal gas pressure. (author)

  18. Fundamental hydrogen interactions with beryllium : a magnetic fusion perspective.

    Energy Technology Data Exchange (ETDEWEB)

    Wampler, William R. (Sandia National Laboratories, Albuquerque, NM); Felter, Thomas E.; Whaley, Josh A.; Kolasinski, Robert D.; Bartelt, Norman Charles

    2012-03-01

    Increasingly, basic models such as density functional theory and molecular dynamics are being used to simulate different aspects of hydrogen recycling from plasma facing materials. These models provide valuable insight into hydrogen diffusion, trapping, and recombination from surfaces, but their validation relies on knowledge of the detailed behavior of hydrogen at an atomic scale. Despite being the first wall material for ITER, basic single crystal beryllium surfaces have been studied only sparsely from an experimental standpoint. In prior cases researchers used electron spectroscopy to examine surface reconstruction or adsorption kinetics during exposure to a hydrogen atmosphere. While valuable, these approaches lack the ability to directly detect the positioning of hydrogen on the surface. Ion beam techniques, such as low energy ion scattering (LEIS) and direct recoil spectroscopy (DRS), are two of the only experimental approaches capable of providing this information. In this study, we applied both LEIS and DRS to examine how hydrogen binds to the Be(0001) surface. Our measurements were performed using an angle-resolved ion energy spectrometer (ARIES) to probe the surface with low energy ions (500 eV - 3 keV He{sup +} and Ne{sup +}). We were able to obtain a 'scattering maps' of the crystal surface, providing insight on how low energy ions are focused along open surface channels. Once we completed a characterization of the clean surface, we dosed the sample with atomic hydrogen using a heated tungsten capillary. A distinct signal associated with adsorbed hydrogen emerged that was consistent with hydrogen residing between atom rows. To aid in the interpretation of the experimental results, we developed a computational model to simulate ion scattering at grazing incidence. For this purpose, we incorporated a simplified surface model into the Kalypso molecular dynamics code. This approach allowed us to understand how the incident ions interacted with the

  19. Beryllium Chelation by Dicarboxylic Acids in Aqueous Solution.

    Science.gov (United States)

    Schmidt, Michael; Bauer, Andreas; Schmidbaur, Hubert

    1997-05-07

    Maleic and phthalic acids are found to react with Be(OH)(2), generated in situ from BeSO(4)(aq) and Ba(OH)(2)(aq), in aqueous solution at pH 3.0 or 4.4, respectively (25 degrees C), to give solutions containing the complexes (H(2)O)(2)Be[(OOCCH)(2)] (1) and (H(2)O)(2)Be[(OOC)(2)C(6)H(4)] (3). The products can be isolated in high yield and identified by microanalytical data. With 2 equiv of the dicarboxylic acids and the pH adjusted to 5.5 and 5.9, respectively, by addition of ammonia, the bis-chelate complexes [(NH(4))(+)](2){[Be[(OOCCH)(2)](2)}(2)(-) (2) and [(NH(4))(+)](2){Be[(OOC)(2)C(6)H(4)](2)}(2)(-) (4) are obtained, which can also be isolated. The compounds show distinct (9)Be, (1)H, and (13)C resonances in their NMR spectra in aqueous solutions. Layering of an aqueous solution of compound 4 with acetone at ambient temperature leads to the precipitation of single crystals suitable for an X-ray structure determination. This salt (5) was found to contain the bis-chelated dianion {Be[(OOC)(2)C(6)H(4)](2)}(2)(-) with the beryllium atom in the spiro center of two seven-membered rings and an overall geometry approaching closely C(2) symmetry. These anions are associated with two crystallographically independent but structurally similar counterions [MeC(O)CH(2)CMe(2)NH(3)](+), which are the product of a condensation reaction of the ammonium cation with the acetone solvent. In the crystal the ammonium hydrogen atoms of the cations form N-H.O hydrogen bonds with the oxo functions of the dianion.

  20. Structure of beryllium isotopes in fermionic molecular dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Torabi, Bahram Ramin

    2009-02-16

    Modern theoretical nuclear physics faces two major challenges. The first is finding a suitable interaction, which describes the forces between nucleons. The second challenge is the solution of the nuclear many-body problem for a given nucleus while applying a realistic potential. The potential used in the framework of this thesis is based on the Argonne AV18 potential. It was transformed by means of the Unitary Correlation Operator Method (UCOM) to optimize convergence. The usual phenomenological corrections were applied to improve the potential for the Hilbert space used in Fermionic Molecular Dynamics (FMD). FMD is an approach to solve the nuclear many-body problem. It uses a single-particle basis which is a superposition of Gaussian distributions in phase-space. The most simple many-body state is the antisymmetric product of the singleparticle states: a Slater determinant, the so called intrinsic state. This intrinsic state is projected on parity, total angular momentum and a center of mass momentum zero. The Hilbert space is spanned by several of these projected states. The states are obtained by minimizing their energy while demanding certain constraints. The expectation values of Slater determinants, parity projected and additionally total angular momentum projected Slater determinants are used. The states that are relevant in the low energy regime are obtained by diagonalization. The lowest moments of the mass-, proton- or neutron-distribution and the excitation in proton- and neutron-shells of a harmonic oscillator are some of the used constraints. The low energy regime of the Beryllium isotopes with masses 7 to 14 is calculated by using these states. Energies, radii, electromagnetic transitions, magnetic moments and point density distributions of the low lying states are calculated and are presented in this thesis. (orig.)

  1. Inhibition of normal human lung fibroblast growth by beryllium.

    Science.gov (United States)

    Lehnert, N M; Gary, R K; Marrone, B L; Lehnert, B E

    2001-03-07

    Inhalation of particulate beryllium (Be) and its compounds causes chronic Be disease (CBD) in a relatively small subset ( approximately 1-6%) of exposed individuals. Hallmarks of this pulmonary disease include increases in several cell types, including lung fibroblasts, that contribute to the fibrotic component of the disorder. In this regard, enhancements in cell proliferation appear to play a fundamental role in CBD development and progression. Paradoxically, however, some existing evidence suggests that Be actually has antiproliferative effects. In order to gain further information about the effects of Be on cell growth, we: (1) assessed cell proliferation and cell cycle effects of low concentrations of Be in normal human diploid fibroblasts, and (2) investigated the molecular pathway(s) by which the cell cycle disturbing effects of Be may be mediated. Treatment of human lung and skin fibroblasts with Be added in the soluble form of BeSO(4) (0.1-100 microM) caused inhibitions of their growth in culture in a concentration-dependent manner. Such growth inhibition was found to persist, even after cells were further cultured in Be(2+)-free medium. Flow cytometric analyses of cellular DNA labeled with the DNA-binding fluorochrome DAPI revealed that Be causes a G(0)-G(1)/pre-S phase arrest. Western blot analyses indicated that the Be-induced G(0)-G(1)/pre-S phase arrest involves elevations in TP53 (p53) and the cyclin-dependent kinase inhibitor CDKN1A (p21(Waf-1,Cip1)). That Be at low concentrations inhibits the growth of normal human fibroblasts suggests the possibility of the existence of abnormal cell cycle inhibitory responses to Be in individuals who are sensitive to the metal and ultimately develop CBD.

  2. Adaptation prevents the extinction of Chlamydomonas reinhardtii under toxic beryllium

    Directory of Open Access Journals (Sweden)

    Beatriz Baselga-Cervera

    2016-03-01

    Full Text Available The current biodiversity crisis represents a historic challenge for natural communities: the environmental rate of change exceeds the population’s adaptation capability. Integrating both ecological and evolutionary responses is necessary to make reliable predictions regarding the loss of biodiversity. The race against extinction from an eco-evolutionary perspective is gaining importance in ecological risk assessment. Here, we performed a classical study of population dynamics—a fluctuation analysis—and evaluated the results from an adaption perspective. Fluctuation analysis, widely used with microorganisms, is an effective empirical procedure to study adaptation under strong selective pressure because it incorporates the factors that influence demographic, genetic and environmental changes. The adaptation of phytoplankton to beryllium (Be is of interest because human activities are increasing the concentration of Be in freshwater reserves; therefore, predicting the effects of human-induced pollutants is necessary for proper risk assessment. The fluctuation analysis was performed with phytoplankton, specifically, the freshwater microalgae Chlamydomonas reinhardtii, under acute Be exposure. High doses of Be led to massive microalgae death; however, by conducting a fluctuation analysis experiment, we found that C. reinhardtii was able to adapt to 33 mg/l of Be due to pre-existing genetic variability. The rescuing adapting genotype presented a mutation rate of 9.61 × 10−6 and a frequency of 10.42 resistant cells per million wild-type cells. The genetic adaptation pathway that was experimentally obtained agreed with the theoretical models of evolutionary rescue (ER. Furthermore, the rescuing genotype presented phenotypic and physiologic differences from the wild-type genotype, was 25% smaller than the Be-resistant genotype and presented a lower fitness and quantum yield performance. The abrupt distinctions between the wild-type and the Be

  3. Microstructural characteristics of joint region during diffusion-brazing of magnesium alloy and stainless steel using pure copper interlayer%纯铜作中间层的镁合金与不锈钢扩散-钎焊接头区的微观结构特征

    Institute of Scientific and Technical Information of China (English)

    袁新建; 盛光敏; 罗军; 李佳

    2013-01-01

    A novel joining method,double-stage diffusion-brazing of an AZ31 magnesium alloy and a 304L austenitic stainless steel,was carried out using a pure copper interlayer.The solid-state diffusion bonding of 304L to copper was conducted at 850 ℃ for 20 min followed by brazing to AZ31 at 520 ℃ and 495 ℃ for various time.Microstructural characteristics of the diffusion-brazed joints were investigated in detail.A defect flee interface of Fe-Cu diffusion area appeared between the Cu alloy and the 304L steel.Cu-Mg reaction products were formed between AZ31 and Cu alloys.A layered structure including AZ31/Cu-Mg compounds/Cu/Fe-Cu diffusion layer/304L was present in the joint.With time prolonging,the reduction in the width of Cu layer was balanced by the increase in the width of Cu-Mg compounds zone.Microhardness peaks in the zone between AZ31 and Cu layer were attributed to the formation of Mg-Cu compounds in this zone.%以纯铜作中间层采用一种新型的两步式扩散-钎焊方法对AZ31镁合金和304L奥氏体不锈钢进行连接.304L与铜的固态扩散连接在850℃下进行20 min,随后与镁合金在520℃和495℃进行不同时间的钎焊.对扩散-钎焊接头区的微观结构特征进行研究.在铜与304L钢之间形成没有缺陷存在的Fe-Cu扩散界面.在AZ31和铜之间形成Cu-Mg反应物.在接头处出现包含AZ31/Cu-Mg化合物/Cu/Fe-Cu扩散层/304L的层状结构.随着时间的延长,铜层的宽度降低,而Cu-Mg化合物层的宽度增加.形成的Mg-Cu化合物使AZ31和铜层之间的区域出现显微硬度的峰值.

  4. Cu2+、Pb2+和Zn2+对大型溞的单一及联合毒性效应%INDIVIDUAL TOXICITY AND JOINT TOXICITY OF COPPER LEAD AND ZINC IONC TO DAPHNIA MAGNA

    Institute of Scientific and Technical Information of China (English)

    丁婵娟; 付荣恕

    2013-01-01

    Research on toxic effect of heavy metal combined pollution plays an importance role in ecological environment evaluation. The individual toxicity and the joint toxicity of Cu2+ 、Pb2 + and Zn2+ to Daphnia magna were investigated with a static test method. Results showed that the toxicity of Cu2+、Pb2+ and Zn2+ was degressive and the joint toxicity of Cu2 + - Zn2 + 、 Cu2 + - Pb2 + and Cu2 + - Pb2 + - Zn2 + was synergetic action, while Pb2 + -Zn + was antagonistic action. Joint toxicity was affected by combined gradation of poisons but it had no relation with ratio of chemical and exposure time.%重金属的复合污染毒性效应研究在生态环境评价中具有重要的实践意义.本研究以大型溞为试验材料,通过静水生物测试法,研究Cu2+、Pb2+和Zn2+三种金属离子对其的单一毒性及联合毒性效应.单一毒性实验结果表明,Cu2+、Pb2+和Zn2+对大型潘的毒性大小顺序为Cu2+> Pb2+> Zn2+.联合毒性实验结果表明,Cu2+-Zn2+、Cu2+-Pb2+和Cu2+-Pb2+-Zn2+三组的联合毒性均表现为协同作用,Pb2+-Zn2+的联合毒性表现为拮抗作用.联合毒性与毒物的组合有关,与毒物配比和暴露时间没有关系.

  5. Wavefunction and energy of the 1s22sns configuration in a beryllium atom

    Institute of Scientific and Technical Information of China (English)

    Huang Shi-Zhong; Ma Kun; Yu Jia-Ming; Liu Fen

    2008-01-01

    A new set of trial functions for 1s22sns configurations in a beryllium atom is suggested.A Mathematica program baaed on the variational method is developed to calculate the wavefunctions and energies of 1s22sns (n=3-6)configurations in a beryllium atom.Non-relativistic energy,polarization correction and relativistic correction which include mass correction,one- and two-body Darwin corrections,spin-spin contact interaction and orbit-orbit interaction,are calculated respectively.The results are in good agreement with experimental data.

  6. Beryllium plasma-facing components for the ITER-like wall project at JET

    Energy Technology Data Exchange (ETDEWEB)

    Rubel, M J; Sundelin, P [Alfven Laboratory, Royal Institute of Technology, Association Euratom-VR (Sweden); Bailescu, V [Nuclear Fuel Plant, Pitesti (Romania); Coad, J P; Matthews, G F; Pedrick, L; Riccardo, V; Villedieu, E [Culham Science Centre, Euratom-UKAEA Fusion Association, Abingdon (United Kingdom); Hirai, T; Linke, J [IEF-2, Forschungszentrum Juelich, Association Euratom-FZJ, Juelich (Germany); Likonen, J [VTT, Association Euratom-Tekes, 02044 VTT (Finland); Lungu, C P [NILPRP, Association Euratom-MEdC, Bucharest (Romania)], E-mail: rubel@kth.se

    2008-03-15

    ITER-Like Wall Project has been launched at the JET tokamak in order to study a tokamak operation with beryllium components on the main chamber wall and tungsten in the divertor. To perform this first comprehensive test of both materials in a thermonuclear fusion environment, a broad program has been undertaken to develop plasma-facing components and assess their performance under high power loads. The paper provides a concise report on scientific and technical issues in the development of a beryllium first wall at JET.

  7. Measurement of neutron yield by 62 MeV proton beam on a thick Beryllium target

    CERN Document Server

    Alba, R; Boccaccio, P; Celentano, A; Colonna, N; Cosentino, G; Del Zoppo, A; Di Pietro, A; Esposito, J; Figuera, P; Finocchiaro, P; Kostyukov, A; Maiolino, C; Osipenko, M; Ricco, G; Ripani, M; Viberti, C M; Santonocito, D; Schillaci, M

    2012-01-01

    In the framework of research on IVth generation reactors and high intensity neutron sources a low-power prototype neutron amplifier was recently proposed by INFN. It is based on a low-energy, high current proton cyclotron, whose beam, impinging on a thick Beryllium converter, produces a fast neutron spectrum. The world database on the neutron yield from thick Beryllium target in the 70 MeV proton energy domain is rather scarce. The new measurement was performed at LNS, covering a wide angular range from 0 to 150 degrees and an almost complete neutron energy interval. In this contribution the preliminary data are discussed together with the proposed ADS facility.

  8. Second hyperpolarizability of delta shaped disubstituted acetylene complexes of beryllium, magnesium, and calcium.

    Science.gov (United States)

    Hatua, Kaushik; Nandi, Prasanta K

    2015-10-01

    Present theoretical study involves the delta shape complexes of beryllium, magnesium, and calcium where the metal atom interacts perpendicularly with disubstituted acetylene. Most of the complexes are found to be fairly stable. The dependence of second-hyperpolarizability on the basis set with increasing polarization and diffuse functions has been examined which showed the importance of 'f-type' type polarization function for heavy metal (Mg, Ca) and 'd-type' polarization function for beryllium. Larger second hyperpolarizability has been predicted for complexes having significant ground state polarization and low lying excited states favoring strong electronic coupling. Transition energy plays the most significant role in modulating the second hyperpolarizability.

  9. Cold melting of beryllium: Atomistic view on Z-machine experiments

    Science.gov (United States)

    Dremov, V. V.; Rykounov, A. A.; Sapozhnikov, F. A.; Karavaev, A. V.; Yakovlev, S. V.; Ionov, G. V.; Ryzhkov, M. V.

    2015-07-01

    Analysis of phase diagram of beryllium at high pressures and temperatures obtained as a result of ab initio calculations and large scale classical molecular dynamics simulations of beryllium shock loading have shown that the so called cold melting takes place when shock wave propagates through polycrystalline samples. Comparison of ab initio calculation results on sound speed along the Hugoniot with experimental data obtained on Z-machine also evidences for possible manifestation of the cold melting. The last may explain the discrepancy between atomistic simulations and experimental data on the onset of the melting on the Hugoniot.

  10. Power deposition modelling of the ITER-like wall beryllium tiles at JET

    Science.gov (United States)

    Firdaouss, M.; Mitteau, R.; Villedieu, E.; Riccardo, V.; Lomas, P.; Vizvary, Z.; Portafaix, C.; Ferrand, L.; Thomas, P.; Nunes, I.; de Vries, P.; Chappuis, P.; Stephan, Y.

    2009-06-01

    A precise geometric method is used to calculate the power deposition on the future JET ITER-Like Wall beryllium tiles with particular emphasis on the internal edge loads. If over-heated surfaces are identified, these can be modified before the machining or failing that actively monitored during operations. This paper presents the methodology applied to the assessment of the main chamber beryllium limiters. The detailed analysis of one limiter is described. The conclusion of this study is that operation will not be limited by edges exposed to plasma convective loads.

  11. Efficacy of surface sampling methods for different types of beryllium compounds.

    Science.gov (United States)

    Dufresne, A; Mocanu, T; Viau, S; Perrault, G; Dion, C

    2011-01-01

    The objective of the research work was to evaluate the efficiency of three different sampling methods (Ghost Wipe™, micro-vacuum, and ChemTest®) in the recovery of Be dust by assessing: (1) four Be compounds (beryllium acetate, beryllium chloride, beryllium oxide and beryllium aluminium), (2) three different surfaces (polystyrene, glass and aluminium) and (3) inter-operator variation. The three sampling methods were also tested on site in a laboratory of a dental school for validation purposes. The Ghost Wipe™ method showed recovery ranging from 43.3% to 85.8% for all four Be compounds and for all three quantities of Be spiked on Petri dishes, while recovery with the micro-vacuum method ranged from 0.1% to 12.4%. On polystyrene dishes with 0.4 µg Be, the recovery ranged from 48.3% to 81.7%, with an average recovery of 59.4% for Operator 1 and 68.4% for Operator 2. The ChemTest® wipe method with beryllium acetate, beryllium chloride, and AlBeMet® showed analogous results that are in line with the manufacturer's manual, but collection of beryllium oxide was negative. In the dental laboratory, Ghost Wipe™ samplings showed better recovery than the micro-vacuum method. The ratios between the recovered quantities of Be in each location where the Ghost Wipe™ was tested differed substantially, ranging from 1.45 to 64. In the dental laboratory, a faint blue color indicating the presence of Be was observed on the ChemTest® wipes used in two locations out of six. In summary, the Ghost Wipe™ method was more efficient than micro-vacuuming in collecting the Be dust from smooth, non-porous surfaces such as Petri dishes by a factor of approximately 18. The results obtained on site in a dental laboratory also showed better recovery with Ghost Wipes™. However, the ratio of Be recovered by Ghost Wipes™ versus micro-vacuuming was much lower for surfaces where a large amount of dust was present. Wet wiping is preferred over micro-vacuuming for beryllium forms, but

  12. Developments of electrical joints for aluminum-stabilized superconducting cables

    CERN Document Server

    Curé, B

    1999-01-01

    Electrical joints for the aluminum-stabilized conductors of the LHC experiment magnets have been studied. Two techniques have been tested: electron beam welding and MIG welding. The joint resistance was measured as a function of the magnetic field on ring shaped samples using the MA.RI.S.A. test facility, wherein current is induced in the test conductor by a varying magnetic field. The resistance is obtained by measuring either the voltage drop or the decay time. Calculation and finite-element simulation have been performed in order to separate the effect of both the copper-aluminum contact resistivity and the aluminum resistivity from the effect due to the joint technique (joint configuration, resistivity of the filler material, increasing of aluminum resistivity in the welding zone). The copper-aluminum contact resistivity and the current transfer length were obtained by measurements of the joint resistance of butt welded samples. (2 refs).

  13. Developments of electrical joints for aluminium stabilized superconducting tables

    CERN Document Server

    Fabbricatore, P; Farinon, S; Horváth, I; Musenich, R; Prian, C

    1999-01-01

    Electrical joints for the aluminum stabilized conductors of the LHC experiment magnets have been studied. Two techniques have been tested: electron beam welding and MIG welding. The joint resistance was measured as a function of the magnetic field on ring shaped samples using the MA.RI.S.A. test facility: varying the magnet field, current is induced in the sample. The resistance is obtained by measuring either the voltage drop or the decay time. Calculation and FE simulation have been performed in order to separate the effect of both the copper-aluminum contact resistivity and the aluminum resistivity from the effect due to the joint technique ( joint configuration, resistivity of the filler material, increasing of aluminum resistivity in the welding zone). The copper-aluminum contact resistivity and the current transfer length were obtained by measurements of the joint resistance of butt welded samples

  14. Assessment of copper resistance to stress-corrosion cracking in nitrite solutions by means of joint analysis of acoustic emission measurements, deformation diagrams, qualitative and quantitative fractography, and non-linear fracture mechanics

    Energy Technology Data Exchange (ETDEWEB)

    Khanzhin, V.G.; Nikulin, S.A. [Moscow State Inst. of Steel and Alloys (Russian Federation)

    2005-06-01

    A study of stress-corrosion cracking (SCC) of copper in 0.1M NaNO{sub 2} aqueous solution is presented. The fracture kinetics was monitored by measuring the acoustic emission (AE) signals. Macro- and micro-fractography analysis, using scanning electron microscopy (SEM), was employed to investigate the fracture mechanisms. Estimates of stress intensity factor, KI, and J-integral were derived in order to assess the resistance of copper to stress corrosion cracking. Two kinds of SCC tests under continuous circulation of the corrosive solution were employed in the present study: 1. Constant extension rate (2x10{sup -6}/s) tests on pre-cracked, middle tension (MT) panel specimens. 2. Tests on pre-cracked, compact tension (CT) specimens at a fixed (by a fixing bolt) opening of the crack walls ({delta} = 0.3 mm, K{sub i} = 27 MPax{radical}m). The time base for these tests was about two months. After the completion of the SCC test, the CT specimen was additionally tested, under a constant-rate (0.02 mm/s) off-center extension. In the both kinds of tests, the SCC fracture kinetics is found to exhibit two typical stages: Stage 1: SCC initiation stage (after a certain incubation period, T{sub i}, measured to be T{sub i} {approx_equal} 3-4 hours for MT specimens under constant extension, the corresponding stress was {sigma} {approx_equal} 40-70 MPa, and T{sub i} {approx_equal} 200 hours for CT specimens under a fixed crack wall opening). Stage 2: Active fracture process (SCC macro-fracture) distinguished by strong AE pulses (which are registered after time T{sub 2} {approx_equal} 8 hours for MT specimens and T{sub 2} {approx_equal} 800 hours for CT specimens). Fractography analysis has shown that the zone of SCC fracture in MT specimens extends to approximately 1,500 {mu}m. A 400-700 {mu}m deep zone of brittle transgranular fracture, which included small areas showing characteristic SCC 'striations', was observed adjacent to the fatigue pre-crack area. At higher

  15. A NEAR REAL-TIME BERYLLIUM MONITOR WITH CAM AND WIPE ANALYSIS CAPABILITIES

    Energy Technology Data Exchange (ETDEWEB)

    D.T. Kendrick; Steven Saggese

    2002-12-01

    Science & Engineering Associates, Inc. (SEA), under contract No. DE-AC26-00NT40768, was tasked by the US Department of Energy--National Energy Technology Laboratory to develop and test a near real-time beryllium monitor for airborne and surface measurements. Recent public awareness of the health risks associated with exposure to beryllium has underscored the need for better, faster beryllium monitoring capabilities within the DOE. A near real-time beryllium monitor will offer significant improvements over the baseline monitoring technology currently in use. Whereas the baseline technology relies upon collecting an air sample on a filter and the subsequent analysis of the filter by an analytical laboratory, this effort developed a monitor that offers near real-time measurement results while work is in progress. Since the baseline typically only offers after-the-fact documentation of exposure levels, the near real-time capability provides a significant increase in worker protection. The beryllium monitor developed utilizes laser induced breakdown spectroscopy, or LIBS as the fundamental measurement technology. LIBS has been used in a variety of laboratory and field based instrumentation to provide real-time, and near-real-time elemental analysis capabilities. LIBS is an analytical technique where a pulsed high energy laser beam is focused to a point on the sample to be interrogated. The high energy density produces a small high temperature plasma plume, sometimes called a spark. The conditions within this plasma plume result in the constituent atoms becoming excited and emitting their characteristic optical emissions. The emission light is collected and routed to an optical spectrometer for quantitative spectral analysis. Each element has optical emissions, or lines, of a specific wavelength that can be used to uniquely identify that element. In this application, the intensity of the beryllium emission is used to provide a quantitative measure of the abundance of the

  16. Chronic Beryllium Disease: revealing the role of beryllium ion and small peptides binding to HLA-DP2.

    Science.gov (United States)

    Petukh, Marharyta; Wu, Bohua; Stefl, Shannon; Smith, Nick; Hyde-Volpe, David; Wang, Li; Alexov, Emil

    2014-01-01

    Chronic Beryllium (Be) Disease (CBD) is a granulomatous disorder that predominantly affects the lung. The CBD is caused by Be exposure of individuals carrying the HLA-DP2 protein of the major histocompatibility complex class II (MHCII). While the involvement of Be in the development of CBD is obvious and the binding site and the sequence of Be and peptide binding were recently experimentally revealed [1], the interplay between induced conformational changes and the changes of the peptide binding affinity in presence of Be were not investigated. Here we carry out in silico modeling and predict the Be binding to be within the acidic pocket (Glu26, Glu68 and Glu69) present on the HLA-DP2 protein in accordance with the experimental work [1]. In addition, the modeling indicates that the Be ion binds to the HLA-DP2 before the corresponding peptide is able to bind to it. Further analysis of the MD generated trajectories reveals that in the presence of the Be ion in the binding pocket of HLA-DP2, all the different types of peptides induce very similar conformational changes, but their binding affinities are quite different. Since these conformational changes are distinctly different from the changes caused by peptides normally found in the cell in the absence of Be, it can be speculated that CBD can be caused by any peptide in presence of Be ion. However, the affinities of peptides for Be loaded HLA-DP2 were found to depend of their amino acid composition and the peptides carrying acidic group at positions 4 and 7 are among the strongest binders. Thus, it is proposed that CBD is caused by the exposure of Be of an individual carrying the HLA-DP2*0201 allele and that the binding of Be to HLA-DP2 protein alters the conformational and ionization properties of HLA-DP2 such that the binding of a peptide triggers a wrong signaling cascade.

  17. Joint purpose?

    DEFF Research Database (Denmark)

    Pristed Nielsen, Helene

    2013-01-01

    Starting from Crenshaw´s point that antiracism often fails to interrogate patriarchy and that feminism often reproduces racist practices (1991: 1252), this paper asks: What are the theoretical reasons for believing that feminism and anti-racism can be regarded as fighting for the joint purpose of...

  18. Handling of Copper and Copper Oxide Nanoparticles by Astrocytes.

    Science.gov (United States)

    Bulcke, Felix; Dringen, Ralf

    2016-02-01

    Copper is an essential trace element for many important cellular functions. However, excess of copper can impair cellular functions by copper-induced oxidative stress. In brain, astrocytes are considered to play a prominent role in the copper homeostasis. In this short review we summarise the current knowledge on the molecular mechanisms which are involved in the handling of copper by astrocytes. Cultured astrocytes efficiently take up copper ions predominantly by the copper transporter Ctr1 and the divalent metal transporter DMT1. In addition, copper oxide nanoparticles are rapidly accumulated by astrocytes via endocytosis. Cultured astrocytes tolerate moderate increases in intracellular copper contents very well. However, if a given threshold of cellular copper content is exceeded after exposure to copper, accelerated production of reactive oxygen species and compromised cell viability are observed. Upon exposure to sub-toxic concentrations of copper ions or copper oxide nanoparticles, astrocytes increase their copper storage capacity by upregulating the cellular contents of glutathione and metallothioneins. In addition, cultured astrocytes have the capacity to export copper ions which is likely to involve the copper ATPase 7A. The ability of astrocytes to efficiently accumulate, store and export copper ions suggests that astrocytes have a key role in the distribution of copper in brain. Impairment of this astrocytic function may be involved in diseases which are connected with disturbances in brain copper metabolism.

  19. OCCURRENCE OF ARSENIC, LEAD, THALLIUM AND BERYLLIUM IN GROUNDWATER

    Directory of Open Access Journals (Sweden)

    Abdul A.J. Mohamed

    2014-01-01

    Full Text Available The occurrence of carcinogenic and heavy metals in groundwater sources in Urban-west region of Zanzibar Island is an issue that is not very well known. This could be also coupled with the absence of drinking water treatment plants. This study for the first time reports on the occurrence and the levels of three carcinogenic metals-Arsenic (As, Beryllium (Be and lead (Pb in thirty groundwater samples collected from Zanzibar’s Urban/West region. The levels of alkalinity, Magnesium (Mg and Thallium (Tl were also determined. The concentrations of As, Be, TI and Pb in the water samples were determined by the Inductively Coupled Plasma-Optical Emission Spectrometry (ICP-OES. Palintest photometry procedures were used to determine the levels of total alkalinity and magnesium. Be, As, Tl and Pb were not detected (nd in some water samples. The ranges of concentrations of Be, As, TI and Pb in the samples were; nd to 6100 ng L-1, nd to 6600 ng L-1, nd to 11600 ng L-1 and nd to 31400 ng L-1 respectively. The levels of total alkalinity varied from 38 to 380 (mg L-1 as CaCO3. The proportions of water samples contaminated with Be, Tl, As and Pb were 43.3, 66.7, 70 and 96.7% respectively. About 23% of the water samples had Pb concentrations beyond WHO limits for safe drinking water, while 30 and 56.67% of the samples had Be and Tl concentrations beyond the US EPA’s maximum limits. The concentration of arsenic in each water sample was within WHO limits. The occurrence and the levels of carcinogenic metals in water sources could be a potential cause of cancer cases in Zanzibar. Therefore, prompt action is required to control the levels of these hazardous metals, and other possible contaminants in Zanzibar’s domestic water systems.

  20. The relationship between gross and net erosion of beryllium at elevated temperature

    Energy Technology Data Exchange (ETDEWEB)

    Doerner, R.P., E-mail: rdoerner@ucsd.edu [Center for Energy Research, University of California in San Diego, La Jolla, CA 92093-0417 (United States); Jepu, I. [National Institute for Lasers, Plasma and Radiation Physics, NILPRP, Magurele, Bucharest 077125 (Romania); Nishijima, D. [Center for Energy Research, University of California in San Diego, La Jolla, CA 92093-0417 (United States); Safi, E.; Bukonte, L.; Lasa, A.; Nordlund, K. [Association EURATOM-Tekes, University of Helsinki, PO Box 43, 00014 University of Helsinki (Finland); Schwarz-Selinger, T. [Max-Planck Institut für Plasmaphysik, EURATOM Association, Boltzmannstrasse 2, D-85748 Garching (Germany)

    2015-08-15

    Surface temperature is a critical variable governing plasma–material interactions. PISCES-B injects controllable amounts of Be impurities into the plasma to balance, or exceed, the erosion rate of beryllium from samples in un-seeded plasma exposures. At low temperature, an order of magnitude more beryllium, than the beryllium mass loss measured in un-seeded discharges, needs to be seeded into the plasma to achieve no mass loss from a sample. At elevated temperature, no mass loss is achieved when the beryllium-seeding rate equals the mass loss rate in un-seeded discharges. Molecular dynamics simulations show that below 500 K, Be adatoms have difficulty surmounting the Ehrlich–Schwoebel barrier at the edge of a terrace. Above this temperature, an Arrhenius behavior is observed with an activation energy of 0.32 eV. Qualitatively, this indicates that at low surface temperature the deposited atoms may be more easily re-eroded, accounting for the increased seeding needed to balance the erosion.

  1. (n,p) emission channeling measurements on ion-implanted beryllium

    CERN Multimedia

    Jakubek, J; Uher, J

    2007-01-01

    We propose to perform emission-channeling measurements using thermal neutron induced proton emission from ion-implanted $^{7}$Be. The physics questions addressed concern the beryllium doping of III-V and II-VI semiconductors and the host dependence of the electron capture half-life of $^{7}$Be.

  2. Experimental bremsstrahlung yields for MeV proton bombardment of beryllium and carbon

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, David D. [Institute for Environmental Research, Australian Nuclear Science and Technology Organisation, Private Mail Bag 1, Menai, NSW 2234 (Australia)], E-mail: dcz@ansto.gov.au; Stelcer, Eduard; Siegele, Rainer; Ionescu, Mihail; Prior, Michael [Institute for Environmental Research, Australian Nuclear Science and Technology Organisation, Private Mail Bag 1, Menai, NSW 2234 (Australia)

    2008-04-15

    Experimental bremsstrahlung yields for 2, 3 and 4 MeV protons on thin beryllium and carbon targets have been measured. The yields have been corrected for detector efficiency, self-absorption in the target and fitted to 9th order polynomials over the X-ray energy range 1-10 keV for easy comparison with theoretical calculations.

  3. Thermo-optical properties of beryllium containing oxide crystals as materials for high power laser systems

    Science.gov (United States)

    Pestryakov, E. V.; Petrov, V. V.; Trunov, V. I.; Kirpichnikov, A. V.; Laptev, A. V.; Matrosov, V. N.

    2007-06-01

    The elastic and thermo-optical properties of chrysoberyl, beryllium hexaaluminate and beryllium-lanthanum hexaaluminate crystals have been experimentally studied. The velocities of elastic-wave propagation in the crystals are measured by acousto-optic interference method. The values of all the independent components of elastic-constant tensor are determined and used to calculate a number of important dynamic parameters of the crystals such as the Young's and shear moduli, the modulus of volume elasticity, Poisson's ratio, the Debye temperature. Also measurements of refractive indices in 25 - 75 C temperature range in VIS spectral region were performed. Using experimental data the dispersion of thermal optical coefficients (dn/dT) was calculated, these data were employed to evaluate the thermal lens in beryllium containing laser crystals. The experimental and calculated data are compared with similar parameters for well-known laser hosts. Some of beryllium containing oxide crystals was shown to be candidates for master oscillator and amplifying stages of high power femtosecond laser systems.

  4. Lifetime Measurements for Electric-Dipole △ n = 0 Transitions in the Beryllium-Like Sulfur

    Institute of Scientific and Technical Information of China (English)

    DU Shu-Bin; YANG Zhi-Hu; CHANG Hong-Wei; SU Hong

    2005-01-01

    @@ We have measured lifetimes of △n = 0 allowed transitions in beryllium-like sulfur using beam foil spectroscopic techniques. The measured values, derived from analysis of arbitrarily normalized decay curves, are presented and compared with theoretical calculations and previous measurements. Accurate probabilities have been determined by the well-known relationship.

  5. Beryllium abundances in parent stars of extrasolar planets 16 Cyg A & B and $\\rho^{1}$ Cnc$^{*}$

    CERN Document Server

    García-López, R J

    1998-01-01

    The Be II 3131 A doublet has been observed in the solar-type stars 16 Cyg A & B and in the late G-type star rho 1 Cnc, to derive their beryllium abundances. 16 Cyg A & B show similar (solar) beryllium abundances while 16 Cyg B, which has been proposed to have a planetary companion of ~2 M_Jup, is known to be depleted in lithium by a factor larger than 6 with respect to 16 Cyg A. Differences in their rotational histories which could induce different rates of internal mixing of material, and the ingestion of a similar planet by 16 Cyg A are discussed as potential explanations. The existence of two other solar-type stars which are candidates to harbour planetary-mass companions and which show lithium and beryllium abundances close to those of 16 Cyg A, requires a more detailed inspection of the peculiarities of the 16 Cyg system. For rho 1 Cnc, which is the coolest known object candidate to harbour a planetary-mass companion (M > 0.85 M_Jup), we establish a precise upper limit for its beryllium abundance...

  6. Beryllium assessment and recommendation for application in ITER plasma facing components

    Energy Technology Data Exchange (ETDEWEB)

    Barabash, V.; Tanaka, S.; Matera, R. [ITER Joint Central Team, Muenchen (Germany)

    1998-01-01

    The design status of the ITER Plasma Facing Components (PFC) is presented. The operational conditions of the armour material for the different components are summarized. Beryllium is the reference armour material for the Primary Wall, Baffle and Limiter and the back-up material for the Divertor Dome. The activities on the selection of the Be grades and the joining technologies are reviewed. (author)

  7. Thermal ramp tritium release in COBRA-1A2 C03 beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Baldwin, D.L. [Pacific Northwest National Lab., Richland, WA (United States)

    1998-03-01

    Tritium release kinetics, using the method of thermal ramp heating at three linear ramp rates, were measured on the COBRA-1A2 C03 1-mm beryllium pebbles. This report includes a brief discussion of the test, and the test data in graph format.

  8. Deep layer-resolved core-level shifts in the beryllium surface

    DEFF Research Database (Denmark)

    Aldén, Magnus; Skriver, Hans Lomholt; Johansson, Börje

    1993-01-01

    Core-level energy shifts for the beryllium surface region are calculated by means of a Green’s function technique within the tight-binding linear muffin-tin orbitals method. Both initial- and final-state effects in the core-ionization process are fully accounted for. Anomalously large energy shifts...

  9. F-4 Beryllium Rudders; A Precis of the Design, Fabrication, Ground and Flight Test Demonstrations

    Science.gov (United States)

    1975-05-01

    Stress concentration factor KIPS (1000 pounds) per square inch Applied moment (usually a Ending moment) Cycles to failure in fatigue; number...Beryllium rudder assembly. A- TEST 2- RUDDER ULTIMATE STATIC TEST WITH MAXIMUM AIRLOAD AT W„ THORn The objective of this test was to demonstrate

  10. Tritium release from advanced beryllium materials after loading by tritium/hydrogen gas mixture

    Energy Technology Data Exchange (ETDEWEB)

    Chakin, Vladimir, E-mail: vladimir.chakin@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Rolli, Rolf; Moeslang, Anton; Kurinskiy, Petr; Vladimirov, Pavel [Karlsruhe Institute of Technology, Institute for Applied Materials, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Dorn, Christopher [Materion Beryllium & Composites, 6070 Parkland Boulevard, Mayfield Heights, OH 44124-4191 (United States); Kupriyanov, Igor [Bochvar Russian Scientific Research Institute of Inorganic Materials, Rogova str., 5, 123098 Moscow (Russian Federation)

    2016-06-15

    Highlights: • A major tritium release peak for beryllium samples occurs at temperatures higher than 1250 K. • A beryllium grade with comparatively smaller grain size has a comparatively higher tritium release compared to the grade with larger grain size. • The pebbles of irregular shape with the grain size of 10–30 μm produced by the crushing method demonstrate the highest tritium release rate. - Abstract: Comparison of different beryllium samples on tritium release and retention properties after high-temperature loading by tritium/hydrogen gas mixture and following temperature-programmed desorption (TPD) tests has been performed. The I-220-H grade produced by hot isostatic pressing (HIP) having the smallest grain size, the pebbles of irregular shape with the smallest grain size (10–30 μm) produced by the crushing method (CM), and the pebbles with 1 mm diameter produced by the fluoride reduction method (FRM) having a highly developed inherent porosity show the highest release rate. Grain size and porosity are considered as key structural parameters for comparison and ranking of different beryllium materials on tritium release and retention properties.

  11. Improved vacuum evaporation unit for beryllium coating for biological X-ray microanalysis.

    Science.gov (United States)

    Marshall, A T; Carde, D; Kent, M

    1985-09-01

    An improved vacuum evaporator is described for coating frozen-hydrated biological samples with beryllium for X-ray microanalysis. The evaporator permits repeated coatings without bringing the main chamber to atmospheric pressure and ambient temperature. The use of a glass sleeve in the evaporation chamber facilitates cleaning.

  12. Lattice Dynamics of Beryllium from a First-Principles Nonlocal Pseudopotential Approach

    DEFF Research Database (Denmark)

    Walter, F. King; Cutler, P. H.

    1970-01-01

    The lattice dynamics of beryllium, a metal with hexagonal close-packed structure and two atoms per unit cell, is investigated within the framework of Harrison's first-principles pseudopotential theory, using (i) the Slater approximation for the conduction-band-core exchange, and (ii) a modified...

  13. Investigation of damages induced by ITER-relevant heat loads during massive gas injections on Beryllium

    Directory of Open Access Journals (Sweden)

    B. Spilker

    2016-12-01

    Full Text Available Massive gas injections (MGIs will be used in ITER to mitigate the strong damaging effect of full performance plasma disruptions on the plasma facing components. The MGI method transforms the stored plasma energy to radiation that is spread across the vacuum vessel with poloidal and toroidal asymmetries. This work investigated the impact of MGI like heat loading on the first wall armor material beryllium. ITER-relevant power densities of 90-260MWm−2in combination with pulse durations of 5-10ms were exerted onto the S-65 grade beryllium specimens in the electron beam facility JUDITH 1. All tested loading conditions led to noticeable surface morphology changes and in the expected worst case scenario, a crater with thermally induced cracks with a depth of up to ∼340µm formed in the loaded area. The level of destruction in the loaded area was strongly dependent on the pulse number but also on the formation of beryllium oxide. The cyclic melting of beryllium could lead to an armor thinning mechanism under the presence of melt motion driving forces such as surface tension, magnetic forces, and plasma pressure.

  14. REQUIREMENTS FOR COLLISION DATA ON THE SPECIES HELIUM, BERYLLIUM AND BORON IN MAGNETIC CONFINEMENT FUSION

    NARCIS (Netherlands)

    SUMMERS, HP; VONHELLERMANN, M; DEHEER, FJ; HOEKSTRA, R

    1992-01-01

    Requirements for collision data on helium, beryllium and boron are reviewed in the light of the directions of present and planned tokamak fusion experiments. The occurrence of the atoms and ions of these species and their roles in plasma behaviour and diagnostic measurements are described. Special e

  15. Tritium release from neutron irradiated beryllium: Kinetics, long-time annealing and effect or crack formation

    Energy Technology Data Exchange (ETDEWEB)

    Scaffidi-Argentina, F.; Werle, H. [Forschungszentrum Karlsruhe, (Germany)

    1995-09-01

    Since beryllium is considered as one of the best neutron multiplier materials in the blanket of the next generation fusion reactors, several studies have been started to evaluate its behaviour under irradiation during both operating and accidental conditions. Based on safety considerations, tritium produced in beryllium during neutron irradiation represents one important issue, therefore it is necessary to investigate tritium transport processes by using a comprehensive mathematical model and comparing its predictions with well characterized experimental tests. Because of the difficulties in extrapolating the short-time tritium release tests to a longer time scale, also long-time annealing experiments with beryllium samples from the SIBELIUS irradiation. have been carried out at the Forschungszentrum Karlsruhe. Samples were annealed up to 12 months at temperatures up to 650{degrees}C. The inventory after annealing was determined by heating the samples up to 1050{degrees}C with a He+0.1 vo1% H{sub 2} purge gas. Furthermore, in order to investigate the likely effects of cracks formation eventually causing a faster tritium release from beryllium, the behaviour of samples irradiated at low temperature (40-50{degrees}C) but up to very high fast neutron fluences (0.8-3.9{center_dot}10{sup 22} cm{sup -2}, E{sub n}{ge}1 MeV) in the BR2 reactor has been investigated. Tritium was released by heating the beryllium samples up to 1050{degrees}C and purging them with He+0.1 vo1% H{sub 2}. Tritium release from high-irradiated beryllium samples showed a much faster kinetics than from the low-irradiated ones, probably because of crack formation caused by thermal stresses in the brittle material and/or by helium bubbles migration. The obtained experimental data have been compared with predictions of the code ANFIBE with the goal to better understand the physical mechanisms governing tritium behaviour in beryllium and to assess the prediction capabilities of the code.

  16. Physical properties of beryllium oxide - Irradiation effects; Proprietes physiques et caracteristiques mecaniques de l'oxyde de beryllium fritte - Effet de l'irradiation et guerison

    Energy Technology Data Exchange (ETDEWEB)

    Elston, J.; Caillat, R. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    This work has been carried out in view of determining several physical properties of hot-pressed beryllium oxide under various conditions and the change of these properties after irradiation. Special attention has been paid on to the measurement of the thermal conductivity coefficient and thermal diffusivity coefficient. Several designs for the measurement of the thermal conductivity coefficient have been achieved. They permit its determination between 50 and 300 deg. C, between 400 and 800 deg. C. Some measurements have been made above 1000 deg. C. In order to measure the thermal diffusivity coefficient, we heat a perfectly flat surface of a sample in such a way that the heat flux is modulated (amplitude and frequency being adjustable). The thermal diffusivity coefficient is deduced from the variations of temperature observed on several spots. Tensile strength; compressive strength; expansion coefficient; sound velocity and crystal parameters have been also measured. Some of the measurements have been carried out after neutron irradiation. Some data have been obtained on the change of the properties of beryllium oxide depending on the integrated neutron flux. (author)Fren. [French] L'objet de cette etude est la determination de plusieurs proprietes physiques de l'oxyde de beryllium fritte sous charge dans differentes conditions et l'evolution de ces proprietes apres irradiation. Une attention particuliere a ete portee sur la mesure de la conductibilite et de la diffusivite thermiques. Differents montages ont ete realises pour mesurer la conductibilite thermique. Ils permettent la determination entre 50 et 300 deg. C, entre 400 et 800 deg. C; quelques mesures ont ete faites au-dessus de 1000 deg. C. Pour la mesure du coefficient de diffusivite thermique, on realise une attaque thermique, de frequence et d'amplitude reglables d'une face parfaitement plane d'un echantillon d'oxyde de beryllium. Les variations de temperature sont

  17. Canine models of copper toxicosis for understanding mammalian copper metabolism

    OpenAIRE

    Fieten, Hille; Leegwater, Peter A. J.; Watson, Adrian L.; Rothuizen, Jan

    2011-01-01

    Hereditary forms of copper toxicosis exist in man and dogs. In man, Wilson’s disease is the best studied disorder of copper overload, resulting from mutations in the gene coding for the copper transporter ATP7B. Forms of copper toxicosis for which no causal gene is known yet are recognized as well, often in young children. Although advances have been made in unraveling the genetic background of disorders of copper metabolism in man, many questions regarding disease mechanisms and copper homeo...

  18. Hair copper in intrauterine copper device users.

    Science.gov (United States)

    Thiery, M; Heyndrickx, A; Uyttersprot, C

    1984-03-01

    The antifertility effect of copper-bearing IUDs is based on continuous release of copper, which is a result of the reaction between the metal and the uterine secretions. Released cupric ions collect in the endometrium and in the uterine fluid but significant accumulation has not been found in the bloodstream or elsewhere. Following Laker's suggestion that hair be used for monitoring essential trace elements, e.g., copper, we checked the copper content of the hair of women wearing copper-bearing IUDs. Samples of untreated pubic hair removed by clipping before diagnostic curettage were obtained from 10 young (24-34 years old), white caucasian females who until then had been wearing an MLCu250 IUD for more than 1 year. Pubes from 10 comparable (sex, age, race) subjects who had never used a Cu-containing device served as controls. The unwashed material was submitted to the toxicology laboratory, where the copper content was assessed by flameless atomic absorption, a technique whose lower limit of measurement lies at a concentration of 0.05 mcg Cu/ml fluid (50 ppb). Hair samples were washed to remove extraneous traces of metal according to the prescriptions of the International Atomic Energy Agency, weighed, and mineralized, after which a small volume (10 mcl) of the diluted fluid was fed into the graphite furnace. Each sample (75-150 mg) was analyzed 4 times, both before and after washing. Since the cleaning procedure reduces the weight of the sample (mainly by the removal of fat, dust, etc.) this explains why the percentage copper content of washed hair is higher than that of unwashed hair belonging to the same subject. The results indicate that there was no significant difference (Mann-Whitney U test) between the mean copper levels of both unwashed and washed pubes from women who were using or had never used an MLCu250 IUD. We therefore conclude that the use of this copper-containing device is not associated with significant accumulation of copper in (pubic) hair.

  19. Beryllium-10 in the Taylor Dome ice core: Applications to Antarctic glaciology and paleoclimatology

    Energy Technology Data Exchange (ETDEWEB)

    Steig, E.J.

    1996-12-31

    An ice core was drilled at Taylor dome, East Antarctica, reaching to bedrock at 554 meters. Oxygen-isotope measurements reveal climatic fluctuations through the last interglacial period. To facilitate comparison of the Taylor Dome paleoclimate record with geologic data and results from other deep ice cores, several glaciological issues need to be addressed. In particular, accumulation data are necessary as input for numerical ice-flow-models, for determining the flux of chemical constituents from measured concentrations, and for calculation of the offset in age between ice and trapped air in the core. The analysis of cosmogenic beryllium-10 provides a geochemical method for constraining the accumulation-rate history at Taylor Dome. High-resolution measurements were made in shallow firn cores and snow pits to determine the relationship among beryllium-10 concentrations, wet and dry deposition mechanisms, and snow-accumulation rates. Comparison between theoretical and measured variations in deposition over the last 75 years constrains the relationship between beryllium-10 deposition and global average production rates. The results indicate that variations in geomagnetically-modulated production-rate do not strongly influence beryllium-10 deposition at Taylor Dome. Although solar modulation of production rate is important for time scales of years to centuries, snow-accumulation rate is the dominant control on ice-core beryllium-10 concentrations for longer periods. Results show that the Taylor Dome core can be used to provide new constraints on regional climate over the last 130,000 years, complementing the terrestrial and marine geological record from the Dry Valley, Transantarctic Mountains and western Ross Sea.

  20. Helium analyses of 1-mm beryllium microspheres from COBRA-1A2

    Energy Technology Data Exchange (ETDEWEB)

    Oliver, B.M. [Pacific Northwest National Lab., Richland, WA (United States)

    1998-03-01

    Multiple helium analyses on four beryllium microspheres irradiated in the Experimental Breeder Reactor-II (EBR-II) at Argonne National Laboratory-West (ANL-W), are reported. The purpose of the analyses was to determine the total helium content of the beryllium, and to determine the helium release characteristics of the beryllium as a function of time and temperature. For the helium release measurements, sequential helium analyses were conducted on two of the samples over a temperature range from 500 C to 1100 C in 100 C increments. Total helium measurements were conducted separately using the normal analysis method of vaporizing the material in a single analysis run. Observed helium release in the two beryllium samples was nonlinear with time at each temperature interval, with each step being characterized by a rather rapid initial release rate, followed by a gradual slowing of the rate over time. Sample Be-C03-1 released virtually all of its helium after approximately 30 minutes at 1000 C, reaching a final value of 2722 appm. Sample Be-D03-1, on the other hand, released only about 62% of its helium after about 1 hour at 1100 c, reaching a final value of 1519 appm. Combining these results with subsequent vaporization runs on the two samples, yielded total helium concentrations of 2724 and 2459 appm. Corresponding helium concentrations measured in the two other C03 and D03 samples, by vaporization alone, were 2941 and 2574 appm. Both sets of concentrations are in reasonable agreement with predicted values of 2723 and 2662 appm. Helium-3 levels measured during the latter two vaporization runs were 2.80 appm for Be-C03-2, and 2.62 appm for Be-D03-2. Calculated {sup 3}He values are slightly lower at 2.55 and 2.50 appm, respectively, suggesting somewhat higher tritium levels in the beryllium than predicted.

  1. Irradiated Beryllium Disposal Workshop, Idaho Falls, ID, May 29-30, 2002

    Energy Technology Data Exchange (ETDEWEB)

    Longhurst, Glen Reed; Anderson, Gail; Mullen, Carlan K; West, William Howard

    2002-07-01

    In 2001, while performing routine radioactive decay heat rate calculations for beryllium reflector blocks for the Advanced Test Reactor (ATR), it became evident that there may be sufficient concentrations of transuranic isotopes to require classification of this irradiated beryllium as transuranic waste. Measurements on samples from ATR reflector blocks and further calculations confirmed that for reflector blocks and outer shim control cylinders now in the ATR canal, transuranic activities are about five times the threshold for classification. That situation implies that there is no apparent disposal pathway for this material. The problem is not unique to the ATR. The High Flux Isotope Reactor at Oak Ridge National Laboratory, the Missouri University Research Reactor at Columbia, Missouri and other reactors abroad must also deal with this issue. A workshop was held in Idaho Falls Idaho on May 29-30, 2002 to acquaint stakeholders with these findings and consider a path forward in resolving the issues attendant to disposition of irradiated material. Among the findings from this workshop were (1) there is a real potential for the US to be dependent on foreign sources for metallic beryllium within about a decade; (2) there is a need for a national policy on beryllium utilization and disposition and for a beryllium coordinating committee to be assembled to provide guidance on that policy; (3) it appears it will be difficult to dispose of this material at the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico due to issues of Defense classification, facility radioactivity inventory limits, and transportation to WIPP; (4) there is a need for a funded DOE program to seek resolution of these issues including research on processing techniques that may make this waste acceptable in an existing disposal pathway or allow for its recycle.

  2. Validation of a standardised method for determining beryllium in human urine at nanogram level.

    Science.gov (United States)

    Devoy, Jérôme; Melczer, Mathieu; Antoine, Guillaume; Remy, Aurélie; Heilier, Jean-François

    2013-10-01

    The potential toxicity of beryllium at low levels of exposure means that a biological and/or air monitoring strategy may be required to monitor the exposure of subjects. The main objective of the work presented in this manuscript was to develop and validate a sensitive and reproducible method for determining levels of beryllium in human urine and to establish reference values in workers and in non-occupationally exposed people. A chelate of beryllium acetylacetonate formed from beryllium(II) in human urine was pre-concentrated on a SPE C18 cartridge and eluted with methanol. After drying the eluate, the residue was solubilised in nitric acid and analysed by atomic absorption spectrometry and/or inductively coupled plasma mass spectrometry. The proposed method is 4 to 100 times more sensitive than other methods currently in routine use. The new method was validated with the concordance correlation coefficient test for beryllium concentrations ranging from 10 to 100 ng/L. Creatinine concentration, urine pH, interfering compounds and freeze-thaw cycles were found to have only slight effects on the performance of the method (less than 6%). The effectiveness of the two analytical techniques was compared statistically with each other and to direct analysis techniques. Even with a detection limit of 0.6 ng/L (obtained with inductively coupled plasma mass spectrometry), the method is not sensitive enough to detect levels in non-occupationally exposed persons. The method performance does however appear to be suitable for monitoring worker exposure in some industrial settings and it could therefore be of use in biological monitoring strategies.

  3. Computational evaluation of unsaturated carbonitriles as neutral receptor model for beryllium(II) recognition.

    Science.gov (United States)

    Rosli, Ahmad Nazmi; Ahmad, Mohd Rais; Alias, Yatimah; Zain, Sharifuddin Md; Lee, Vannajan Sanghiran; Woi, Pei Meng

    2014-12-01

    Design of neutral receptor molecules (ionophores) for beryllium(II) using unsaturated carbonitrile models has been carried out via density functional theory, G3, and G4 calculations. The first part of this work focuses on gas phase binding energies between beryllium(II) and 2-cyano butadiene (2-CN BD), 3-cyano propene (3-CN P), and simpler models with two separate fragments; acrylonitrile and ethylene. Interactions between beryllium(II) and cyano nitrogen and terminal olefin in the models have been examined in terms of geometrical changes, distribution of charge over the entire π-system, and rehybridization of vinyl carbon orbitals. NMR shieldings and vibrational frequencies probed charge centers and strength of interactions. The six-membered cyclic complexes have planar structures with the rehybridized carbon slightly out of plane (16° in 2-CN BD). G3 results show that in 2-CN BD complex participation of vinyl carbon further stabilizes the cyclic adduct by 16.3 kcal mol(-1), whereas, in simpler models, interaction between beryllium(II) and acetonitrile is favorable by 46.4 kcal mol(-1) compared with that of ethylene. The terminal vinyl carbon in 2-CN BD rehybridizes to sp (3) with an increase of 7 % of s character to allow interaction with beryllium(II). G4 calculations show that the Be(II) and 2-CN BD complex is more strongly bound than those with Mg(II) and Ca(II) by 98.5 and 139.2 kcal mol(-1) (-1), respectively. QST2 method shows that the cyclic and acyclic forms of Be(II)-2-CN BD complexes are separated by 12.3 kcal mol(-1) barrier height. Overlap population analysis reveals that Ca(II) can be discriminated based on its tendency to form ionic interaction with the receptor models.

  4. China Copper Processing Industry Focus

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    <正>1. Market Consumption The ’China Factor’ and Copper Price Fluctuation We all know China is an enormous consumer of copper,but the exact levels of consumption and where the copper has gone remains a mystery.

  5. Biogenic nanoparticles: copper, copper oxides, copper sulphides, complex copper nanostructures and their applications.

    Science.gov (United States)

    Rubilar, Olga; Rai, Mahendra; Tortella, Gonzalo; Diez, Maria Cristina; Seabra, Amedea B; Durán, Nelson

    2013-09-01

    Copper nanoparticles have been the focus of intensive study due to their potential applications in diverse fields including biomedicine, electronics, and optics. Copper-based nanostructured materials have been used in conductive films, lubrification, nanofluids, catalysis, and also as potent antimicrobial agent. The biogenic synthesis of metallic nanostructured nanoparticles is considered to be a green and eco-friendly technology since neither harmful chemicals nor high temperatures are involved in the process. The present review discusses the synthesis of copper nanostructured nanoparticles by bacteria, fungi, and plant extracts, showing that biogenic synthesis is an economically feasible, simple and non-polluting process. Applications for biogenic copper nanoparticles are also discussed.

  6. Modeling the diffusion of solid copper into liquid solder alloys

    Energy Technology Data Exchange (ETDEWEB)

    Rizvi, M.J. [School of Computing and Mathematical Sciences, University of Greenwich, 30 Park Row, London, SE10 9LS (United Kingdom)], E-mail: rm77@gre.ac.uk; Lu, H.; Bailey, C. [School of Computing and Mathematical Sciences, University of Greenwich, 30 Park Row, London, SE10 9LS (United Kingdom)

    2009-01-01

    During the soldering process, the copper atoms diffuse into liquid solders. The diffusion process determines integrity and the reworking possibility of a solder joint. In order to capture the diffusion scenarios of solid copper into liquid Sn-Pb and Sn-Cu solders, a computer modeling has been performed for 10 s. An analytical model has also been proposed for calculating the diffusion coefficient of copper into liquid solders. It is found that the diffusion coefficient for Sn-Pb solder is 2.74 x 10{sup -10} m{sup 2}/s and for Sn-Cu solder is 6.44 x 10{sup -9} m{sup 2}/s. The modeling results reveal that the diffusion coefficient is one of the major factors that govern the rate at which solid Cu dissolve in the molten solder. The predicted dissolved amounts of copper into solders have been validated with the help of scanning electron microscopic analysis.

  7. Dissolution of FB-Line Residues Containing Beryllium Metal

    Energy Technology Data Exchange (ETDEWEB)

    RUDISILL, TRACY S.; CROWDER, MARK L.

    2005-09-06

    Scrap materials containing plutonium (Pu) metal were dissolved at the Savannah River Site (SRS) as part of a program to disposition nuclear materials during the deactivation of the FB-Line facility. Some of these items contained both Pu and beryllium (Be) metal as a composite material. The Pu and Be metals were physically separated to minimize the amount of Be associated with the Pu; however, a dissolution flowsheet was required to dissolve small amounts of Be combined with the Pu metal using a dissolving solution containing nitric acid (HNO{sub 3}) and potassium fluoride (KF). Since the dissolution of Pu metal in HNO{sub 3}/fluoride (F{sup -}) solutions was well understood, the primary focus of the flowsheet development was the dissolution of Be metal. Initially, small-scale experiments were used to measure the dissolution rate of Be metal foils using conditions effective for the dissolution of Pu metal. The experiments demonstrated that the dissolution rate was nearly independent of the HNO{sub 3} concentration over the limited range of investigation and only a moderate to weak function of the F{sup -} concentration. The effect of temperature was more pronounced, significantly increasing the dissolution rate between 40 and 105 C. The offgas analysis from three Be metal foil dissolutions demonstrated that the production of hydrogen (H{sub 2}) was sensitive to the HNO{sub 3} concentration, decreasing by a factor of approximately two when the concentration was increased from 4 to 8 M. In subsequent experiments, complete dissolution of Be samples from a Pu/Be composite material was achieved in a 4 M HNO{sub 3} solution containing 0.1-0.2 M KF. Gas samples collected during each experiment showed that the maximum H{sub 2} generation rate occurred at temperatures below 70-80 C. A Pu metal dissolution experiment was performed using a 4 M HNO{sub 3}/0.1 M KF solution at 80 C to demonstrate flowsheet conditions developed for the dissolution of Be metal. As the reaction

  8. Joint purpose?

    DEFF Research Database (Denmark)

    Pristed Nielsen, Helene

    2013-01-01

    of anti-discrimination in Europe today? And what empirical evidence may be found for such a joint approach? The paper discusses how the contemporary EU context differs from the American context which prompted Crenshaw to raise the point about intersectionality, and it analyses documents and interviews...... from each of the two European umbrella organisations the European Women´s Lobby and the European Network against Racism, as well as a number of their national member organisations from across Europe, both within EU and non-EU member states....

  9. 金属铍的应用进展%Progress in Application of Metallic Beryllium

    Institute of Scientific and Technical Information of China (English)

    钟景明; 许德美; 李春光; 王战宏; 李峰; 王莉; 李志年

    2014-01-01

    This paper mainly reviews the up-to-date progress of metallic beryllium applications in nuclear reactors,iner-tial navigation system,optics,thermotics,structure parts,high-energy physics and typical commercial use in the recent 20 years,as well as gives brief introduction that excellent performances of metallic beryllium play an important role in pro-moting technology development of its application field and improving product performance and quality.Based on the range and effect of metallic beryllium application,the paper details that metallic beryllium as key strategic engineering material has given strong support to national defense,aerospace and strategic nuclear energy development.Moreover,the paper briefly introduces status of metallic beryllium applications in China,and points out that China should greatly improve the level of beryllium application in inertial navigation system and the infrared optical system,so as to enhance China′s space fighting and confrontations ability.Finally,the paper summarizes pattern of metallic beryllium market.It can be expected that metallic beryllium market is still defense,aerospace and strategic nuclear,and metallic beryllium will consistently play an important role in civil industry in future.%综述了近20年来金属Be在核能、惯性导航系统、红外光学系统、热学、结构件、高能物理学和商业等领域的最新应用进展,以及金属Be优异的性能在促进其应用领域技术进步和改进产品性能和质量中所起的重要作用。从金属Be的应用范围和效果,说明金属Be作为“战略性、关键性”工程材料,对一个国家国防、航空航天和战略核能发展所起的关键支撑作用。并简要介绍了我国金属Be的应用现状,指出我国必须大幅度提高Be在惯性导航系统和红外光学系统的应用水平,以增强我国空间争夺和对抗能力。最后,总结了世界范围内金属Be的应用市场格局,预

  10. 78 FR 42584 - Bureau of International Security and Nonproliferation: Report to Congress Pursuant to Section...

    Science.gov (United States)

    2013-07-16

    ..., military, or ballistic missile programs of Iran: aluminum; beryllium; boron; cobalt; copper; copper infiltrated tungsten; copper- beryllium; graphite; hastelloy; inconel; magnesium; molybdenum; nickel;...

  11. All-solid-state continuous-wave laser systems for ionization, cooling and quantum state manipulation of beryllium ions

    CERN Document Server

    Lo, H -Y; Kienzler, D; Keitch, B C; de Clercq, L E; Negnevitsky, V; Home, J P

    2013-01-01

    We describe laser systems for photoionization, Doppler cooling and quantum state manipulation of beryllium ions. For photoionization of neutral beryllium, we have developed a continuous-wave 235 nm source obtained by two stages of frequency doubling from a diode laser at 940 nm. The system delivers up to 400 mW at 470 nm and 28 mW at 235 nm. For control of the beryllium ion, three laser wavelengths at 313 nm are produced by sum-frequency generation and second-harmonic generation from four infrared fiber lasers. Up to 7.2 W at 626 nm and 1.9 W at 313 nm are obtained using two pump beams at 1051 and 1551 nm. Intensity fluctuations below 0.5 % per hour (during 8 hours of operation) have been measured at a 313 nm power of 1 W. These systems are used to load beryllium ions into a segmented ion trap.

  12. Reproducibility and correctness of the procedure of photometric determination of beryllium with 2-(o-hydroxyphenyl)benzoxazole

    Energy Technology Data Exchange (ETDEWEB)

    Tikhonova, N.B.; Charykov, A.K.; Gladilovich, D.B.

    1985-09-01

    This paper discusses two methods of evaluation of correctness on the example of the fluorometric determination of beryllium by 2-(o-hydroxyphenyl) benzoxazole (HPBO), as well as an evaluation of the reproducibility of this procedure for the level of beryllium concentration 10-36 ng/ml. The traditional method of detection and evaluation of systematic errors in chemical analysis is comparison of the average result of repeated analysis of a standard sample with specified content of the component to be determined. The second method discussed is based on an experimental estimation of the constant and proportional components of the systematic error by a combination of the methods of doubling and additives. It is shown that the fluorometric method of determining beryllium with HPBO at an absolute beryllium content of 0.25-1.0 micrograms is satisfactorily reproducible and does not contain systematic errors at the level of significance beta=0.05.

  13. Copper and silver halates

    CERN Document Server

    Woolley, EM; Salomon, M

    2013-01-01

    Copper and Silver Halates is the third in a series of four volumes on inorganic metal halates. This volume presents critical evaluations and compilations for halate solubilities of the Group II metals. The solubility data included in this volume are those for the five compounds, copper chlorate and iodate, and silver chlorate, bromate and iodate.

  14. Coping with copper

    DEFF Research Database (Denmark)

    Nunes, Ines; Jacquiod, Samuel; Brejnrod, Asker

    2016-01-01

    Copper has been intensively used in industry and agriculture since mid-18(th) century and is currently accumulating in soils. We investigated the diversity of potential active bacteria by 16S rRNA gene transcript amplicon sequencing in a temperate grassland soil subjected to century-long exposure......, suggesting a potential promising role as bioindicators of copper contamination in soils....

  15. Diffusion Bonding of Tungsten to Copper and Its Alloy with Ti Foil and Ti/Ni/Ti Multiple Interlayers

    Institute of Scientific and Technical Information of China (English)

    Guisheng ZOU; Jun YANG; Aaiping WU; Genghua HUANG; Deku ZHANG; Jialie REN; Qing WANG

    2003-01-01

    Ti foil and Ti/Ni/Ti multiple interlayers were selected for the bonding of tungsten to copper and CuCrZr alloy. Theeffects of processing conditions on the microstructures and shear strength of the joints were investigated.

  16. Interfacial microstructure and properties of copper clad steel produced using friction stir welding versus gas metal arc welding

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Z.; Chen, Y. [Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo (Canada); Haghshenas, M., E-mail: mhaghshe@uwaterloo.ca [Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo (Canada); Nguyen, T. [Mechanical Systems Engineering, Conestoga College, Kitchener (Canada); Galloway, J. [Welding Engineering Technology, Conestoga College, Kitchener (Canada); Gerlich, A.P. [Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo (Canada)

    2015-06-15

    A preliminary study compares the feasibility and microstructures of pure copper claddings produced on a pressure vessel A516 Gr. 70 steel plate, using friction stir welding versus gas metal arc welding. A combination of optical and scanning electron microscopy is used to characterize the grain structures in both the copper cladding and heat affected zone in the steel near the fusion line. The friction stir welding technique produces copper cladding with a grain size of around 25 μm, and no evidence of liquid copper penetration into the steel. The gas metal arc welding of copper cladding exhibits grain sizes over 1 mm, and with surface microcracks as well as penetration of liquid copper up to 50 μm into the steel substrate. Transmission electron microscopy reveals that metallurgical bonding is produced in both processes. Increased diffusion of Mn and Si into the copper cladding occurs when using gas metal arc welding, although some nano-pores were detected in the FSW joint interface. - Highlights: • Cladding of steel with pure copper is possible using either FSW or GMAW. • The FSW yielded a finer grain structure in the copper, with no evidence of cracking. • The FSW joint contains some evidence of nano-pores at the interface of the steel/copper. • Copper cladding by GMAW contained surface cracks attributed to high thermal stresses. • The steel adjacent to the fusion line maintained a hardness value below 248 HV.

  17. Kunpeng Copper:The largest Copper Smelting Company of Sichuan

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>On September 9,Liangshan Mining Company’s 100,000 tons/year cathode copper project kicked off.It is another key project of the company following the successful launch of the 100,000 tons/year anode copper project.Based on ISA copper smelting technology of the largest open-cast copper mine in southwest China,

  18. Understanding the photomagnetic behavior in copper octacyanomolybdates.

    Science.gov (United States)

    Bunău, O; Arrio, M-A; Sainctavit, Ph; Paulatto, L; Calandra, M; Juhin, A; Marvaud, V; Cartier dit Moulin, C

    2012-08-30

    The mechanism of photomagnetism in copper octacyanomolybdate molecules is currently under debate. Contrary to the general belief that the photomagnetic transition occurs only due to a photoinduced electron transfer from the molybdenum to the copper atom, recent X-ray magnetic dichroic (XMCD) data clearly indicate that this phenomenon is associated at low temperature to a local low-spin-high-spin transition on the molybdenum atom. In this article we provide theoretical justification for these experimental facts. We show the first simulation of X-ray absorption (XAS) and magnetic circular dichroism (XMCD) spectra at the L(2,3) edges of molybdenum from the joint perspective of density functional theory (DFT) calculations and ligand field multiplet (LFM) theory. The description of electronic interactions seems mandatory for reproducing the photomagnetic state.

  19. Characteristics of microstructure and tritium release properties of different kinds of beryllium pebbles for application in tritium breeding modules

    Energy Technology Data Exchange (ETDEWEB)

    Kurinskiy, P., E-mail: petr.kurinskiy@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials – Applied Materials Physics (IAM-AWP), P.O. Box 3640, Karlsruhe 76021 (Germany); Vladimirov, P.; Moeslang, A. [Karlsruhe Institute of Technology, Institute for Applied Materials – Applied Materials Physics (IAM-AWP), P.O. Box 3640, Karlsruhe 76021 (Germany); Rolli, R. [Karlsruhe Institute of Technology, Institute for Applied Materials – Materials and Biomechanics (IAM-WBM), P.O. Box 3640, Karlsruhe 76021 (Germany); Zmitko, M. [The European Joint Undertaking for ITER and the Development of Fusion Energy, c/Josep Pla, no. 2, Torres Diagonal Litoral, Edificio B3, Barcelona 08019 (Spain)

    2014-10-15

    Highlights: • Tritium release properties and characteristics of microstructure of beryllium pebbles having different sizes of grains were studied. • Fine-grained beryllium pebbles showed the best ability to release tritium compared to pebbles from another charges. • Be pebbles with the grain sizes exceeding 100 μm contain a great number of small pores and inclusions presumably referring to the history of material fabrication. • The sizes of grains are one of a key characteristic of microstructure which influences the parameters of tritium release. - Abstract: Beryllium pebbles with diameters of 1 mm are considered to be perspective material for the use as neutron multiplier in tritium breeding modules of fusion reactors. Up to now, the design of helium-cooled breeding blanket in ITER project foresees the use of 1 mm beryllium pebbles fabricated by NGK Insulators Ltd., Japan. It is notable that beryllium pebbles from Russian Federation and USA are also available and the possibility of their large-scale fabrication is under study. Presented work is dedicated to a study of characteristics of microstructure and parameters of tritium release of beryllium pebbles produced by Bochvar Institute, Russian Federation, and Materion Corporation, USA.

  20. Posttranslational regulation of copper transporters

    NARCIS (Netherlands)

    van den Berghe, P.V.E.

    2009-01-01

    The transition metal copper is an essential cofactor for many redox-active enzymes, but excessive copper can generate toxic reactive oxygen species. Copper homeostasis is maintained by highly conserved proteins, to balance copper uptake, distribution and export on the systemic and cellular level. Th