WorldWideScience

Sample records for beds technical progress

  1. Volatiles combustion in fluidized beds. [Quarterly] technical progress report, 4 December 1994--4 March 1995

    Energy Technology Data Exchange (ETDEWEB)

    Pendergrass II, R.A.; Mansker, L.D.; Hesketh, R.P.

    1995-08-01

    The goal of this project is to investigate the conditions in which volatiles will bum within both the dense and freeboard regions of fluidized beds. Experiments using a fluidized bed operated at incipient fluidization are being conducted to characterize the effect of particle surface area, initial fuel concentration, and particle type on the inhibition of volatiles within a fluidized bed. The work conducted during the period 4 December, 1994 through, 3 March 1995 is presented in this technical progress report. The research consists of the application of a detailed chemical kinetics model for propane combustion and planned improvements in the experimental system.

  2. Nucla circulating atmospheric fluidized bed demonstration project. Quarterly technical progress report, October--December 1990

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-31

    During the fourth quarter of 1990, steady-state performance testing at the Nucla Circulating Fluidized Bed (CFB) resumed under sponsorship of the US Department of Energy. Co-sponsorship of the Demonstration Test Program by the Electric Power Research Institute (EPRI) was completed on June 15, 1990. From October through December, 1990, Colorado-Ute Electric Association (CUEA) completed a total of 23 steady-state performance tests, 4 dynamic tests, and set operating records during November and December as the result of improved unit operating reliability. Highlight events and achievements during this period of operation are presented.

  3. Spectral analysis of CFB data: Predictive models of Circulating Fluidized Bed combustors. 11th technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Gamwo, I.K.; Miller, A.; Gidaspow, D.

    1992-04-01

    The overall objective of this investigation is to develop experimentally verified models for circulating fluidized bed (CFB) combustors. Spectral analysis of CFB data obtained at Illinois Institute of Technology shows that the frequencies of pressure oscillations are less than 0.1 Hertz and that they increase with solids volume fraction to the usual value of one Hertz obtained in bubbling beds. These data are consistent with the kinetic theory interpretation of density wave propagation.

  4. Quarterly Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    Ayman I. Hawari

    2002-12-30

    This report presents the progress made during the first quarter of phase 2 for the project entitled ''Development and Validation of Thermal Neutron Scattering Laws from Applications and Safety Implications in Generation IV Reactor Designs.'' (B204) THIS IS NOT A FINAL REPORT

  5. Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-01

    This report summarizes experimental and theoretical work in basic nuclear physics carried out between October 1, 1995, the closing of our last Progress Report, and September 30, 1996 at the Nuclear Physics Laboratory of the University of Colorado, Boulder, under contracts DE-FG03-93ER-40774 and DE-FG03-95ER-40913 with the United States Department of Energy. The experimental contract supports broadly-based experimental research in intermediate energy nuclear physics. This report includes results from studies of Elementary Systems involving the study of the structure of the nucleon via polarized high-energy positron scattering (the HERMES experiment) and lower energy pion scattering from both polarized and unpolarized nucleon targets. Results from pion- and kaon-induced reactions in a variety of nuclear systems are reported under the section heading Meson Reactions; the impact of these and other results on understanding the nucleus is presented in the Nuclear Structure section. In addition, new results from scattering of high-energy electrons (from CEBAF/TJNAF) and pions (from KEK) from a broad range of nuclei are reported in the section on Incoherent Reactions. Finally, the development and performance of detectors produced by the laboratory are described in the section titled Instrumentation.

  6. Pressurized fluidized bed combustion second-generation system research and development. Technical progress for Phase 2 and Phase 3, October 1, 1997--September 30, 1998

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, A.; Horazak, D.; Newby, R.; Rehmat, A.; White, J.

    1998-10-01

    When DOE funds were exhausted in March 1995, all Phase 2 activities were placed on hold. In February 1996 a detailed cost estimate was submitted to the DOE for completing the two remaining Phase 2 Multi Annular Swirl Burner (MASB) topping combustor test burns; in August 1996 release was received from METC to proceed with these tests. The first test (Test Campaign No.3) will be conducted to: (1) test the MASB at proposed demonstration plant full to minimum loading operating conditions; (2) identify the lower oxygen limit of the MASB; and (3) demonstrate natural gas to carbonizer fuel gas switching. The Livingston Phase 3 Pilot Plant was last operated under contract DE-AC21-86MC21023 in September 1995 for seven days in an integrated carbonizer-CPFBC configuration. In May, 1996, the pilot plant was transferred to Contract DE-AC22-95PC95143 to allow testing in support of the High Performance Power Systems (HIPPS) Program. The HIPPS Program required modifications to the pilot plant and the following changes were incorporated: (1) installation of a dense phase transport system for loading pulverized coal into the feed system lock hopper directly from a pneumatic transport truck; (2) removal of the char transfer pipe between the char collecting hopper and the CPFBC to allow carbonizer only operation; (3) installation of a lock hopper directly under the char collecting hopper to facilitate char removal from the process, the hopper vent gases exhaust to the carbonizer baghouse filter and the depressured char is transferred via nitrogen to the CPFBC baghouse for dumping into drums; (4) removal of the carbonizer cyclone and top of bed overflow drain line; all material elutriated from the carbonizer bed will thus be removed by the 22-element Westinghouse ceramic candle filter; (5) replacement of the carbonizer continuous bottom bed drain (screw feeder) with a batch-type drain removal system; and (6) installation of a mass spectrometer that draws sample gas via a steam jacketed

  7. Pressurized fluidized bed combustion second-generation system research and development. Technical progress for Phase 2 and Phase 3, October 1, 1997--September 30, 1998

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, A.; Horazak, D.; Newby, R.; Rehmat, A.; White, J.

    1998-10-01

    When DOE funds were exhausted in March 1995, all Phase 2 activities were placed on hold. In February 1996 a detailed cost estimate was submitted to the DOE for completing the two remaining Phase 2 Multi Annular Swirl Burner (MASB) topping combustor test burns; in August 1996 release was received from METC to proceed with these tests. The first test (Test Campaign No.3) will be conducted to: (1) test the MASB at proposed demonstration plant full to minimum loading operating conditions; (2) identify the lower oxygen limit of the MASB; and (3) demonstrate natural gas to carbonizer fuel gas switching. The Livingston Phase 3 Pilot Plant was last operated under contract DE-AC21-86MC21023 in September 1995 for seven days in an integrated carbonizer-CPFBC configuration. In May, 1996, the pilot plant was transferred to Contract DE-AC22-95PC95143 to allow testing in support of the High Performance Power Systems (HIPPS) Program. The HIPPS Program required modifications to the pilot plant and the following changes were incorporated: (1) installation of a dense phase transport system for loading pulverized coal into the feed system lock hopper directly from a pneumatic transport truck; (2) removal of the char transfer pipe between the char collecting hopper and the CPFBC to allow carbonizer only operation; (3) installation of a lock hopper directly under the char collecting hopper to facilitate char removal from the process, the hopper vent gases exhaust to the carbonizer baghouse filter and the depressured char is transferred via nitrogen to the CPFBC baghouse for dumping into drums; (4) removal of the carbonizer cyclone and top of bed overflow drain line; all material elutriated from the carbonizer bed will thus be removed by the 22-element Westinghouse ceramic candle filter; (5) replacement of the carbonizer continuous bottom bed drain (screw feeder) with a batch-type drain removal system; and (6) installation of a mass spectrometer that draws sample gas via a steam jacketed

  8. Flue gas desulfurization by rotating beds. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, N.; Keyvani, M.; Coskundeniz, A.

    1992-12-01

    The operating and mass transfer characteristics of rotating foam metal beds were studied to determine the potential for flue gas desulfurization. This is a final technical report on the work supported by DOE {number_sign}FG22-87-PC79924. The report is divided into two sections, Part 1 deals primarily with the operating characteristics of rotating beds, and Part 2 covers the mass transfer characteristics of S0{sub 2} absorption in water-lime slurries. Rotating foam metal beds are in essence packed towers operated in high gravitational fields. The foam metal bed is in the form of a cylindrical donut, or torus, and is rotated to produced the high centrifugal forces. The liquid phase enters the bed at the inner surface of the torus and is pulled by the field through the bed. Gas flows countercurrent to the liquid. The bed packing can have a very large specific surface areas and not flood. Possible benefits include much smaller height of a transfer unit resulting in smaller equipment and supporting structures, reduced solvent inventory, faster response with improved process control, reduced pressure drop, and shorter startup and shut-down times. This work is concerned broadly with the operating characteristics of rotating beds, the objectives being to (1) determine the pressure drop through the rotating bed; (2) determine the power required to operate the beds, (3) investigate the residence time distribution of the liquid phase in the beds; and (4) determine the mass transfer coefficients of S0{sub 2} absorption. Three packings of differing specific surface areas were studied, with areas ranging from 656 to 2952 m{sub 2}/m{sub 3}. Liquid flow rates to 36 kg/s*m{sub 2}, gas flow rate to 2.2 kg/s*m{sub 2}, and gravitational fields to 300 g were covered in this study.

  9. Fluid bed solids heater. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Preuit, L. C.

    1980-01-01

    A solids heater which operates at up to 2000 F was designed, fabricated, installed and operated through checkout at the Morgantown Energy Technology Center at Morgantown, West Virginia. The system, designated the 2000 F Fluid Bed Solids Heater (FBSH) uses a fluidized bed to heat limestone to 600 F and aluminium oxide or silicon carbide to 2000 F and discharges heated solids upon demand. The FBSH with added valve handling and pressurization equipment is known as the Valve Hot Solids Test Unit and is intended for use by the US Department of Energy for testing of valves for severe service applications in coal conversion and utilization processes. The FBSH as designed and supplied by Combustion Power Company includes process equipment, controls, the enclosing building and other associated equipment. In the 600 F range of operation it can circulate limestone through two valve test trains simultaneously on a continuous basis. Only one valve test train is used for 2000 F solids and operation in that range is also continuous. Limestone, crushed to minus 5/16 size, is heated, discharged, and recycled at a maximum average rate of 250 lb/min while aluminum oxide or silicon carbide, No. 8 grit, is circulated at rates up to 167 lb/min. The FBSH control system is designed for automatic operation, and capability is included for external computerized data acquisition and/or supervisory control. An operating and maintenance manual and as-built drawings have been submitted. This report describes the FBSH equipment, its design basis, and its operation. It has been prepared and submitted in fulfillment of Contract Number DIAC05-77ET10499.

  10. Technical evaluation: pressurized fluidized-bed combustion technology

    Energy Technology Data Exchange (ETDEWEB)

    Miller, S A; Vogel, G J; Gehl, S M; Hanway, Jr, J E; Henry, R F; Parker, K M; Smyk, E B; Swift, W M; Podolski, W F

    1982-04-01

    The technology of pressurized fluidized-bed combustion, particularly in its application to a coal-burning combined-cycle plant, is evaluated by examining the technical status of advanced-concept plant components - boiler system (combustor, air-handling and air-injection equipment, and heat exchangers); solids handling, injection, and ejection system; hot-gas cleanup equipment; instrumentation/control system; and the gas turbine - along with materials of plant construction. Environmental performance as well as energy efficiency are examined, and economic considerations are reviewed briefly. The evaluation concludes with a broad survey of the principal related research and development programs in the United States and other countries, a foreview of the most likely technological developments, and a summary of unresolved technical issues and problems.

  11. Technical progress in pipeline design and construction

    Energy Technology Data Exchange (ETDEWEB)

    Hausken, K.B.

    1995-12-31

    This paper considers the technical progress in offshore pipeline construction with limitation to some general subjects covering pipeline design, installation and start-up. In future the use of limit state pipeline design philosophy, may be implemented as an alternative to the stress based design commonly used to day giving a potential for further optimisation of the pipeline design and consequently reduction of the initial investment. Comprehensive research and development efforts in Norway in the second half of the 1970`s, made it technically feasible to cross the deep water Norwegian Trench in the 1980`s. In addition, the development of several offshore pipeline systems until to day including gas distribution systems to the European continent, have brought Norway to the forefront of technical expertise

  12. Sludge Treatment Evaluation: 1992 Technical progress

    Energy Technology Data Exchange (ETDEWEB)

    Silva, L J; Felmy, A R; Ding, E R

    1993-01-01

    This report documents Fiscal Year 1992 technical progress on the Sludge Treatment Evaluation Task, which is being conducted by Pacific Northwest Laboratory. The objective of this task is to develop a capability to predict the performance of pretreatment processes for mixed radioactive and hazardous waste stored at Hanford and other US Department of Energy (DOE) sites. Significant cost savings can be achieved if radionuclides and other undesirable constituents can be effectively separated from the bulk waste prior to final treatment and disposal. This work is initially focused on chemical equilibrium prediction of water washing and acid or base dissolution of Hanford single-shell tank (SST) sludges, but may also be applied to other steps in pretreatment processes or to other wastes. Although SST wastes contain many chemical species, there are relatively few constituents -- Na, Al, NO[sub 3], NO[sub 2], PO[sub 4], SO[sub 4], and F -- contained in the majority of the waste. These constituents comprise 86% and 74% of samples from B-110 and U-110 SSTS, respectively. The major radionuclides of interest (Cs, Sr, Tc, U) are present in the sludge in small molal quantities. For these constituents, and other important components that are present in small molal quantities, the specific ion-interaction terms used in the Pitzer or NRTL equations may be assumed to be zero for a first approximation. Model development can also be accelerated by considering only the acid or base conditions that apply for the key pretreatment steps. This significantly reduces the number of chemical species and chemical reactions that need to be considered. Therefore, significant progress can be made by developing all the specific ion interactions for a base model and an acid dissolution model.

  13. Works Technical Department progress report, March 1961

    Energy Technology Data Exchange (ETDEWEB)

    None

    1961-04-19

    This document details the activities of the Savannah River Works Technical Department during the month of March 1961. Topics discussed are: Reactor Technology, Separations Technology, Engineering Assistance, Health Physics, Laboratories Overview, and Technical Papers Issued.

  14. Solar thermal power systems. Annual technical progress report, FY 1978

    Energy Technology Data Exchange (ETDEWEB)

    1979-06-01

    A technical progress report on the DOE Solar Thermal Power Systems Program is given. Emphasis is on the technical progress of the projects rather than on activities and individual contractor efforts. Each project description indicates its place in the prior to FY 1978 is given; the significant achievements and real progress of each project during FY 1978 are described; and future project activities as well as anticipated significant achievements for each project are forecast. (WHK)

  15. Geomorphology of ice stream beds: recent progress and future challenges

    Science.gov (United States)

    Stokes, Chris R.

    2016-04-01

    Ice sheets lose mass primarily by melting and discharge via rapidly-flowing ice streams. Surface and basal melting (e.g. of ice shelves) are closely linked to atmospheric and oceanic conditions, but the mechanisms that drive changes in ice stream discharge are more complex; and are influenced by conditions at their bed which can sustain, enhance or inhibit their motion. Although explicit comparisons are rare, the ice-bed interface is similar to the 'boundary layer' in fluvial and aeolian environments, where shear stresses (both basal and lateral in the case of ice streams) oppose the flow of the overlying medium. The analogy extends further because processes within the boundary layer create a distinctive geomorphology (and roughness) that is characterised by subglacial bedforms that resemble features in fluvial and aeolian environments. Their creation results from erosion, transport and deposition of sediment which is poorly constrained, but which is intimately linked to the mechanisms through which ice streams are able to flow rapidly. The study of ice stream geomorphology is, therefore, critical to our understanding of their dynamics. Despite difficulty in observing the subglacial environment of active ice streams, our understanding of their geomorphology has grown rapidly in the last three decades, from almost complete ignorance to a detailed knowledge of their geomorphological products. This has been brought about by two main approaches: (i) geophysical investigation of modern (active) ice streams, and (ii) sedimentological and geomorphological investigation of palaeo-ice stream beds. The aim of this paper is to review progress in these two areas, highlight the key questions that remain, and discuss the opportunities that are likely to arise that will enable them to be addressed. It is clear that whilst these two main approaches have led to important advances, they have often been viewed as separate sub-disciplines, with minimal cross-pollination of ideas and

  16. Solar lease grant program. Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    1981-04-01

    Progress on a lease program for the installation of a solar water heater with no installation charge is reported. Information on the announcement of the program, the selection of participants, the contractural agreement, progress on installation of equipment, monitoring, and evaluation is summarized. The status of the budget concerned with the program is announced. Forms used for applications for the program and an announcement from Resource Alternatives for Cilco customers are presented.

  17. Quarterly technical progress report, April-June 1982

    Energy Technology Data Exchange (ETDEWEB)

    None

    1984-04-01

    Progress reports are presented for the following tasks: (1) preparation of low-rank coals; application of liquefaction processes to low-rank coals; (2) slagging fixed-bed gasification; (3) atmospheric fluidized-bed combustion of low-rank coal; (4) ash fouling and combustion modification for low-rank coal; (5) combined flue gas cleanup/simultaneous SO/sub x/-NO/sub x/ control; (6) particulate control and hydrocarbons and trace element emissions from low-rank coals; (7) waste characterization and disposal; and (9) exploratory research.

  18. Technical progress and its factors in Russia’s economy

    Directory of Open Access Journals (Sweden)

    Simon György Jr.

    2010-01-01

    Full Text Available In this paper long-term growth in Russia’s economy is viewed in the context of technical progress, based on both neoclassical and endogenous theories. The dynamics of economic growth with some aspects of catch-up development are examined, as well as capital deepening. TFP is quantified in terms of both output and productivity increases to reveal the leading role of embodied technical progress in productivity growth. An endogenous growth model helped to discern three complex factors of technical progress in the Russian economy, to which at the macro level a factor related to natural wealth (oil and gas resources was added. This enabled the author to conclude that the most important macroeconomic factor of Russia’s technical progress in the half century from the early 1960s to the late 2000s was its immobile component. At the manufacturing level the situation was more complicated, as the initial leadership of creative technical progress was superseded by the dominance of the mobile factor. The collapse of the Soviet Union made the Russian economy more service-oriented and radically changed the conditions of economic modernization, in which technology transfer ensured by FDI began to play a more prominent part, particularly after the default of 1998.

  19. Final Technical Progress Report NANOSTRUCTURED MAGNETIC MATERIALS

    Energy Technology Data Exchange (ETDEWEB)

    Charles M. Falco

    2012-09-13

    This report describes progress made during the final phase of our DOE-funded program on Nanostructured Magnetic Materials. This period was quite productive, resulting in the submission of three papers and presentation of three talks at international conferences and three seminars at research institutions. Our DOE-funded research efforts were directed toward studies of magnetism at surfaces and interfaces in high-quality, well-characterized materials prepared by Molecular Beam Epitaxy (MBE) and sputtering. We have an exceptionally well-equipped laboratory for these studies, with: Thin film preparation equipment; Characterization equipment; Equipment to study magnetic properties of surfaces and ultra-thin magnetic films and interfaces in multi-layers and superlattices.

  20. Technical Entrepreneurship and Technological Progress in Developing Countries.

    Science.gov (United States)

    Quevedo-Procel, Jose

    This paper describes the Mexican economic environment in terms of general economic conditions from the 1940s to the present, the role of science and technology in industrial progress, and the promotion and support of small companies. The technical entrepreneur is identified as the missing link that would play an important part in the technological…

  1. Plan and Design Meticulously and Promoting Technical Progress

    Institute of Scientific and Technical Information of China (English)

    Miao Chengwu

    1994-01-01

    @@ Plan and design is the key link in captial construction, and the soul of engineering construction. China Petroleum Planning & Engineering Institute (CPPEI) is one of the main undertakers for planning and designing of petroleum industry,the only leading multi-functional institute with the first class design certificate. Now it has been an organization under the China National Petroleum Corporation(CNPC)for making development strategy planning, project evaluations and technical consulting, drawing up project development plan and providing technical recommendations. It can complete plan and design for the oil and gas field facilities, pipeline construction,petroleum relinery and petro-chemical industry engineering at home and abroad. It is also a center of servicing for new technical development and scientific research. Since CPPEI was established in 1978,it has meticulously conducted on planning and designing for the technical progress of petroleum engineering.

  2. Swallowable Wireless Capsule Endoscopy: Progress and Technical Challenges

    Directory of Open Access Journals (Sweden)

    Guobing Pan

    2012-01-01

    Full Text Available Wireless capsule endoscopy (WCE offers a feasible noninvasive way to detect the whole gastrointestinal (GI tract and revolutionizes the diagnosis technology. However, compared with wired endoscopies, the limited working time, the low frame rate, and the low image resolution limit the wider application. The progress of this new technology is reviewed in this paper, and the evolution tendencies are analyzed to be high image resolution, high frame rate, and long working time. Unfortunately, the power supply of capsule endoscope (CE is the bottleneck. Wireless power transmission (WPT is the promising solution to this problem, but is also the technical challenge. Active CE is another tendency and will be the next geneion of the WCE. Nevertheless, it will not come true shortly, unless the practical locomotion mechanism of the active CE in GI tract is achieved. The locomotion mechanism is the other technical challenge, besides the challenge of WPT. The progress about the WPT and the active capsule technology is reviewed.

  3. Solar thermal power systems. Annual technical progress report, FY 1979

    Energy Technology Data Exchange (ETDEWEB)

    Braun, Gerald W.

    1980-06-01

    The Solar Thermal Power Systems Program is the key element in the national effort to establish solar thermal conversion technologies within the major sectors of the national energy market. It provides for the development of concentrating mirror/lens heat collection and conversion technologies for both central and dispersed receiver applications to produce electricity, provide heat at its point of use in industrial processes, provide heat and electricity in combination for industrial, commercial, and residential needs, and ultimately, drive processes for production of liquid and gaseous fuels. This report is the second Annual Technical Progress Report for the Solar Thermal Power Systems Program and is structured according to the organization of the Solar Thermal Power Systems Program on September 30, 1979. Emphasis is on the technical progress of the projects rather than on activities and individual contractor efforts. Each project description indicates its place in the Solar Thermal Power Systems Program, a brief history, the significant achievements and real progress during FY 1979, also future project activities as well as anticipated significant achievements are forecast. (WHK)

  4. International Linear Collider-A Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    Elsen, Eckhard; /DESY; Harrison, Mike; /Brookhaven; Hesla, Leah; /Fermilab; Ross, Marc; /Fermilab; Royole-Degieux, Perrine; /Paris, IN2P3; Takahashi, Rika; /KEK, Tsukuba; Walker, Nicholas; /DESY; Warmbein, Barbara; /DESY; Yamamoto, Akira; /KEK, Tsukuba; Yokoya, Kaoru; /KEK, Tsukuba; Zhang, Min; /Beijing, Inst. High Energy Phys.

    2011-11-04

    The International Linear Collider: A Technical Progress Report marks the halfway point towards the Global Design Effort fulfilling its mandate to follow up the ILC Reference Design Report with a more optimised Technical Design Report (TDR) by the end of 2012. The TDR will be based on much of the work reported here and will contain all the elements needed to propose the ILC to collaborating governments, including a technical design and implementation plan that are realistic and have been better optimised for performance, cost and risk. We are on track to develop detailed plans for the ILC, such that once results from the Large Hadron Collider (LHC) at CERN establish the main science goals and parameters of the next machine, we will be in good position to make a strong proposal for this new major global project in particle physics. The two overriding issues for the ILC R&D programme are to demonstrate that the technical requirements for the accelerator are achievable with practical technologies, and that the ambitious physics goals can be addressed by realistic ILC detectors. This GDE interim report documents the impressive progress on the accelerator technologies that can make the ILC a reality. It highlights results of the technological demonstrations that are giving the community increased confidence that we will be ready to proceed with an ILC project following the TDR. The companion detector and physics report document likewise demonstrates how detector designs can meet the ambitious and detailed physics goals set out by the ILC Steering Committee. LHC results will likely affect the requirements for the machine design and the detectors, and we are monitoring that very closely, intending to adapt our design as those results become available.

  5. Environmental Research Division technical progress report, January 1984-December 1985

    Energy Technology Data Exchange (ETDEWEB)

    1986-05-01

    Technical progress in the various research and assessment activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1984 to 1985. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Environmental Impacts, Fundamental Molecular Physics and Chemistry, and Waste Management Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter.

  6. Technical Division quarterly progress report, January 1--March 31, 1977

    Energy Technology Data Exchange (ETDEWEB)

    Slansky, C.M. (ed.)

    1977-05-01

    Progress is reported in three categories: Fuel Cycle Research and Development, special materials production, and projects supporting energy development. Results are presented on the fluidized-bed calcination of high-level radioactive waste from the reprocessing of spent commercial nuclear fuel, on the post treatment of the calcine, and on the removal of actinide elements from the waste prior to calcination. Other projects include the development of storage technology for /sup 85/Kr waste; a study of the hydrogen mordenite catalyzed reaction between NO/sub x/ and NH/sub 3/; the adsorption and storage of /sup 129/I on silver exchanged mordenite; physical properties, materials of construction, and unit operations studies on the evaporation of high-level waste; the behavior of volatile radionuclides during the combustion of HTGR graphite-based fuel; and the use of fission product ruthenium in age-dating uranium ore bodies. The long-term management of defense waste from the ICPP covers post-calcination treatment of ICPP calcined waste. Improvements are reported on the Fluorinel head end process for Zircaloy-clad fuels. Studies are included on nuclear materials security; application of a liquid-solid fluidized-bed heat exchanger to the recovery of geothermal heat; inplant reactor source term measurements; burnup methods for fast breeder reactor fuels; research on analytical methods; and the behavior of environmental species of iodine.

  7. Review of the Technical Status on the Debris Bed Cooling Model

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Eui Kwang; Cho, Chung Ho; Lee, Yong Bum

    2007-09-15

    Preliminary safety analyses of the KALIMER-600 design have shown that the design has inherent safety characteristics and is capable of accommodating double-fault initiators such as ATWS events without coolant boiling or fuel melting. However, for the future design of sodium cooled fast reactor, the evaluation of the safety performance and the determination of containment requirements may be worth due consideration of triple-fault accident sequences of extremely low probability of occurrence that leads to core melting. For any postulated accident sequence which leads to core melting, in-vessel retention of the core debris will be required as a design requirement for the future design of sodium cooled fast reactor. Also, proof of the capacity of the debris bed cooling is an essential condition to solve the problem of in-vessel retention of the core debris. In this study, review of the technical status on the debris bed cooling model was carried out for in-vessel retention of the core debris0.

  8. Technical scheme and corresponding experiment for the PAT performance of a lasercom using an integrated test-bed

    Science.gov (United States)

    Sun, Jianfeng; Liu, Liren; Wang, Lijuan; Luan, Zhu; Liu, De'an; Xu, Nan; Zhong, Xianghong

    2007-09-01

    Recent successful demonstrations of laser communications have demonstrated the feasibility of some of the key aspects of this technology. The demonstrations can not success without the full-up ground test and validation. So an integrate test-bed was build in build to test the technical parameters and to verify the working performance for the optical pointing, acquisition and tracking (PAT) of various inter-satellite lasercom terminals. In this paper, we detail the test technical scheme (TTS) and the corresponding experiments. The integrate test-bed is a high quality optical system that will measure the key characteristics of lasercom terminals, such as point error, tracking error, acquisition possibility etc.. The test-bed can operate over the relative wavelength range. Through quantitative tests, the terminal could be optimized base on the test results.

  9. Advanced Coal Conversion Process Demonstration Project. Technical progress report, January 1, 1993--December 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-02-01

    This report describes the technical progress made on the Advanced Coal Conversion Process (ACCP) Demonstration Project from January 1, 1993, through December 31, 1993. This project demonstrates an advanced, thermal, coal drying process, coupled with physical cleaning techniques, that is designed to upgrade high-moisture, low- rank coals to a high-quality, low-sulfur fuel, registered as the SynCoal{reg_sign} process. The coal is processed through three stages (two heating stages followed by an inert cooling stage) of vibrating fluidized bed reactors that remove chemically bound water, carboxyl groups, and volatile sulfur compounds. After thermal processing, the coal is put through a deep-bed stratifier cleaning process to separate the pyrite-rich ash from the coal. Rosebud SynCoal Partnership`s ACCP Demonstration Facility entered Phase III, Demonstration Operation, in April 1992 and operated in an extended startup mode through August 10, 1993, when the facility became commercial. Rosebud SynCoal Partnership instituted an aggressive program to overcome startup obstacles and now focuses on supplying product coal to customers. Significant accomplishments in the history of the SynCoal{reg_sign} process development are shown in Appendix A.

  10. Thermal energy storage technical progress report, April 1992--March 1993

    Energy Technology Data Exchange (ETDEWEB)

    Olszewski, M.

    1993-05-01

    The Department of Energy (DOE) is supporting development of thermal energy storage (TES) as a means of efficiently coupling energy supplies to variable heating or cooling demands. Uses of TES include electrical demand-side management in buildings and industry, extending the utilization of renewable energy resources such as solar, and recovery of waste heat from periodic industrial processes. Technical progress to develop TES for specific diurnal and industrial applications under the Oak Ridge National Laboratory`s TES program from April 1992 to March 1993 is reported and covers research in the areas of low temperature sorption, thermal energy storage water heater, latent heat storage wallboard and latent/sensible heat regenerator technology development.

  11. Advanced coal conversion process demonstration. Technical progress report for the period July 1, 1995--September 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-01

    This report describes the technical progress made on the Advanced Coal Conversion Process (ACCP) Demonstration Project from July 1, 1995 through September 30, 1995. The ACCP Demonstration Project is a US Department of Energy (DOE) Clean Coal Technology Project. This project demonstrates an advanced, thermal, coal upgrading process, coupled with physical cleaning techniques, that is designed to upgrade high-moisture, low-rank coals to a high-quality, low-sulfur fuel, registered as the SynCoal process. The coal is processed through three stages (two heating stages followed by an inert cooling stage) of vibrating fluidized bed reactors that remove chemically bound water, carboxyl groups, and volatile sulfur compounds. After thermal upgrading, the cola is put through a deep-bed stratifier cleaning process to separate the pyrite-rich ash from the coal.

  12. Technical and economic assessment of fluidized bed augmented compressed air energy storage system. Volume III. Preconceptual design

    Energy Technology Data Exchange (ETDEWEB)

    Giramonti, A.J.; Lessard, R.D.; Merrick, D.; Hobson, M.J.

    1981-09-01

    A technical and economic assessment of fluidized bed combustion augmented compressed air energy storage systems is presented. The results of this assessment effort are presented in three volumes. Volume III - Preconceptual Design contains the system analysis which led to the identification of a preferred component configuration for a fluidized bed combustion augmented compressed air energy storage system, the results of the effort which transformed the preferred configuration into preconceptual power plant design, and an introductory evaluation of the performance of the power plant system during part-load operation and while load following.

  13. Progressing innovation in biomaterials. From the bench to the bed of patients.

    Science.gov (United States)

    Bayon, Y; Bohner, M; Eglin, D; Thérin, M; Montali, A; Procter, P; Fisher, J; Richards, R G

    2015-09-01

    A Translational Research Symposium was organized at the 2014 annual meeting of the European society for biomaterials. This brought together leading Tier one companies in clinical biomaterials and medical device markets, small and medium enterprises and entrepreneurial academics who shared their experiences on taking biomaterials technologies to commercial endpoints, in the clinics. The symposium focused on "Progressing Innovation in Biomaterials. From the Bench to the Bed of Patients". The aim of the present document is to illustrate the content of the symposium and to highlight the key lessons from selected lectures.

  14. Modern problems of technical progress and methodological support in medicine

    Science.gov (United States)

    Novyc'kyy, Victor V.; Lushchyk, Ulyana B.

    2001-06-01

    A rapid development of modern computer technologies gave a powerful incentive to technical progress as a whole and to medical equipment in particular. A range of medical diagnostic computer-based systems has recently appeared. There are various fields these techniques are used in: roentgenology, ultrasound diagnostic, neurophysiology, angiology etc. The advantages of the use of computer interface are undoubted: it gives possibility to enhance the functioning of the system itself, speed up all technological processes, carry out a reliable and easy archivation and exchange the information obtained. But the most important advantage of using PC in diagnostic system lies in an unlimited freedom of use mathematical algorithms and flexible mathematical models for processing information obtained. On the other hand, the absence of clinical techniques for interpretation of the data obtained is an obstacle to the use of software at its full potential. As a result, a close connection of a scientific development of hardware with high-informative techniques for clinical interpretation of the instrumental data obtained has become topical as never before. We see an optimal solution in introducing the interpretation patterns in conjunction with purely numerical computations into mathematical simulations.

  15. FY 1992 work plan and technical progress reports

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-11-01

    The Desert Research Institute (DRI) is a division of the University of Nevada System devoted to multidisciplinary scientific research. For more than 25 years, DRI has conducted research for the US Department of Energy`s Nevada Field Office (DOE/NV) in support of operations at the Nevada Test Site (NTS). During that time, the research program has grown from an early focus on hydrologic studies to include the areas of geology, archaeology, environmental compliance and monitoring, statistics, database management, public education, and community relations. The range of DRI`s activities has also expanded to include a considerable amount of management and administrative support in addition to scientific investigations. DRI`s work plan for FY 1992 reflects a changing emphasis in DOE/NV activities from nuclear weapons testing to environmental restoration and monitoring. Most of the environmental projects from FY 1991 are continuing, and several new projects have been added to the Environmental Compliance Program. The Office of Technology Development Program, created during FY 1991, also includes a number of environmental projects. This document contains the FY 1992 work plan and quarterly technical progress reports for each DRI project.

  16. Summary of Technical Meeting To Compare US/French Approaches for Physical Protection Test Beds

    Energy Technology Data Exchange (ETDEWEB)

    Mack, Thomas Kimball [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Martinez, Ruben [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Thomas, Gerald [National Nuclear Security Administration (NNSA), Washington, DC (United States); Palut, Jean-Michel [French Alternative and Atomic Energy Commission (CEA), Fontenay Aux Roses (France)

    2016-01-01

    In September 2015, representatives of the US Department of Energy/National Nuclear Security Administration, including test bed professionals from Sandia National Laboratories, and representatives of the French Alternative Energies and Atomic Energy Commission participated in a one-week workshop to share best practices in design, organization, operations, utilization, improvement, and performance testing of physical protection test beds. The intended workshop outcomes were to (1) share methods of improving respective test bed methodologies and programs and (2) prepare recommendations for standards regarding creating and operating testing facilities for nations new to nuclear operations. At the workshop, the French and American subject matter experts compared best practices as developed at their respective test bed sites; discussed access delay test bed considerations; and presented the limitations/ constraints of physical protection test beds.

  17. Development of a solar desiccant dehumidifier. Third technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Gunderson, M.E.

    1979-06-12

    This program is aimed at the development of a solar desiccant dehumidifier featuring a rotary bed of granular silica gel and a rotary regenerator. Design, fabrication, performance, commercialization studies, and test stand development are described in detail. (WHK)

  18. Effect of Climatic Conditions on Differences in Thermo-Technical Properties of Organic Bedding in Laboratory Testing

    Directory of Open Access Journals (Sweden)

    Lendelová Jana

    2017-03-01

    Full Text Available The aim of this experiment was to analyse the influence of climatic factors on the thermal performance of separated liquid manure. The samples of organic bedding were collected from the lying area of dairy housing and preparatory store. The measurement of properties of recycled manure solids (RMS was carried out in laboratory conditions. Samples were examined with determining the temperature effect on the thermal conductivity λ of ’dry‘ separated liquid manure (with a dry matter content of 60% and ’wet‘ liquid manure (with a dry matter content of 26%, in air temperatures ranging from 0 °C to 40 °C. Subsequently, the thermal resistance of three selected types of cows lying structures was calculated for winter and summer boundary values. Based on the results of thermal conductivity and thermal resistance, it was observed that dry separated liquid manure as an alternative bedding has, in low temperature (up to 5 °C, the most suitable thermal performance if it is maintained in a dry condition (with a dry matter content of 60%. With increasing temperature (above 20 °C and increasing humidity of bedding (below 26%, thermo-technical properties get worse; however, when comparing the thermal resistance of the cow bed structure with sandwich mattresses with a 50 mm layer of organic bedding and the deep cubicle filled with 200 mm of organic bedding, the thermal resistance of floor structure decreases by 7.6% or 18.4%, respectively. With a proper handling of the recycled organic bedding, it is possible to use its economic advantages.

  19. Advanced Coal Conversion Process Demonstration Project. Final technical progress report, January 1, 1995--December 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-01

    This report describes the technical progress made on the Advanced Coal Conversion Process (ACCP) Demonstration Project from January 1, 1995 through December 31, 1995. This project demonstrates an advanced, thermal, coal upgrading process, coupled with physical cleaning techniques, that is designed to upgrade high-moisture, low-rank coals to a high-quality, low-sulfur fuel, registered as the SynCoal Process. The coal is processed through three stages (two heating stages followed by an inert cooling stage) of vibrating fluidized bed reactors that remove chemically bound water, carboxyl groups, and volatile sulfur compounds. After thermal upgrading, the coal is put through a deep-bed stratifier cleaning process to separate the pyrite-rich ash from the coal. The SynCoal Process enhances low-rank, western coals, usually with a moisture content of 25 to 55 percent, sulfur content of 0.5 to 1.5 percent, and heating value of 5,5000 to 9,000 British thermal units per pound (Btu/lb), by producing a stable, upgraded, coal product with a moisture content as low as 1 percent, sulfur content as low as 0.3 percent, and heating value up to 12,000 Btu/lb. During this reporting period, the primary focus for the ACCP Demonstration Project team was to expand SynCoal market awareness and acceptability for both the products and the technology. The ACCP Project team continued to focus on improving the operation, developing commercial markets, and improving the SynCoal products as well as the product`s acceptance.

  20. Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3

    Energy Technology Data Exchange (ETDEWEB)

    Ulm, Franz-Josef

    2000-03-31

    OAK-B135 Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3(NOTE: Part II A item 1 indicates ''PAPER'', but a report is attached electronically)

  1. Responsive copolymers for enhanced petroleum recovery. Quarterly technical progress report, December 22, 1993--March 21, 1994

    Energy Technology Data Exchange (ETDEWEB)

    McCormick, C.; Hester, R.

    1994-06-01

    The overall goal of this research is the development of advanced water-soluble copolymers for use in enhanced oil recovery. This report summarizes technical progress for the following tasks: advanced copolymer synthesis; and characterization of molecular structure of copolymers.

  2. Verification of Steelmaking Slags Iron Content Final Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    J.Y. Hwang

    2006-10-04

    The steel industry in the United States generates about 30 million tons of by-products each year, including 6 million tons of desulfurization and BOF/BOP slag. The recycling of BF (blast furnace) slag has made significant progress in past years with much of the material being utilized as construction aggregate and in cementitious applications. However, the recycling of desulfurization and BOF/BOP slags still faces many technical, economic, and environmental challenges. Previous efforts have focused on in-plant recycling of the by-products, achieving only limited success. As a result, large amounts of by-products of various qualities have been stockpiled at steel mills or disposed into landfills. After more than 50 years of stockpiling and landfilling, available mill site space has diminished and environmental constraints have increased. The prospect of conventionally landfilling of the material is a high cost option, a waste of true national resources, and an eternal material liability issue. The research effort has demonstrated that major inroads have been made in establishing the viability of recycling and reuse of the steelmaking slags. The research identified key components in the slags, developed technologies to separate the iron units and produce marketable products from the separation processes. Three products are generated from the technology developed in this research, including a high grade iron product containing about 90%Fe, a medium grade iron product containing about 60% Fe, and a low grade iron product containing less than 10% Fe. The high grade iron product contains primarily metallic iron and can be marketed as a replacement of pig iron or DRI (Direct Reduced Iron) for steel mills. The medium grade iron product contains both iron oxide and metallic iron and can be utilized as a substitute for the iron ore in the blast furnace. The low grade iron product is rich in calcium, magnesium and iron oxides and silicates. It has a sufficient lime value and

  3. Verification of Steelmaking Slags Iron Content Final Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    J.Y. Hwang

    2006-10-04

    The steel industry in the United States generates about 30 million tons of by-products each year, including 6 million tons of desulfurization and BOF/BOP slag. The recycling of BF (blast furnace) slag has made significant progress in past years with much of the material being utilized as construction aggregate and in cementitious applications. However, the recycling of desulfurization and BOF/BOP slags still faces many technical, economic, and environmental challenges. Previous efforts have focused on in-plant recycling of the by-products, achieving only limited success. As a result, large amounts of by-products of various qualities have been stockpiled at steel mills or disposed into landfills. After more than 50 years of stockpiling and landfilling, available mill site space has diminished and environmental constraints have increased. The prospect of conventionally landfilling of the material is a high cost option, a waste of true national resources, and an eternal material liability issue. The research effort has demonstrated that major inroads have been made in establishing the viability of recycling and reuse of the steelmaking slags. The research identified key components in the slags, developed technologies to separate the iron units and produce marketable products from the separation processes. Three products are generated from the technology developed in this research, including a high grade iron product containing about 90%Fe, a medium grade iron product containing about 60% Fe, and a low grade iron product containing less than 10% Fe. The high grade iron product contains primarily metallic iron and can be marketed as a replacement of pig iron or DRI (Direct Reduced Iron) for steel mills. The medium grade iron product contains both iron oxide and metallic iron and can be utilized as a substitute for the iron ore in the blast furnace. The low grade iron product is rich in calcium, magnesium and iron oxides and silicates. It has a sufficient lime value and

  4. Processes and parameters involved in modeling radionuclide transport from bedded salt repositories. Final report. Technical memorandum

    Energy Technology Data Exchange (ETDEWEB)

    Evenson, D.E.; Prickett, T.A.; Showalter, P.A.

    1979-07-01

    The parameters necessary to model radionuclide transport in salt beds are identified and described. A proposed plan for disposal of the radioactive wastes generated by nuclear power plants is to store waste canisters in repository sites contained in stable salt formations approximately 600 meters below the ground surface. Among the principal radioactive wastes contained in these canisters will be radioactive isotopes of neptunium, americium, uranium, and plutonium along with many highly radioactive fission products. A concern with this form of waste disposal is the possibility of ground-water flow occurring in the salt beds and endangering water supplies and the public health. Specifically, the research investigated the processes involved in the movement of radioactive wastes from the repository site by groundwater flow. Since the radioactive waste canisters also generate heat, temperature is an important factor. Among the processes affecting movement of radioactive wastes from a repository site in a salt bed are thermal conduction, groundwater movement, ion exchange, radioactive decay, dissolution and precipitation of salt, dispersion and diffusion, adsorption, and thermomigration. In addition, structural changes in the salt beds as a result of temperature changes are important. Based upon the half-lives of the radioactive wastes, he period of concern is on the order of a million years. As a result, major geologic phenomena that could affect both the salt bed and groundwater flow in the salt beds was considered. These phenomena include items such as volcanism, faulting, erosion, glaciation, and the impact of meteorites. CDM reviewed all of the critical processes involved in regional groundwater movement of radioactive wastes and identified and described the parameters that must be included to mathematically model their behavior. In addition, CDM briefly reviewed available echniques to measure these parameters.

  5. Technical progress of nuclear energy: economic and environmental prospects

    Energy Technology Data Exchange (ETDEWEB)

    Naudet, G.

    1994-12-31

    This document deals with three different aspects of the nuclear energy: first the operating and economic performances of nuclear power plants in the world, the French nuclear competitiveness. Then, the technical and economic perspectives about reactors and fuels cycle and the advantages towards atmospheric pollution are discussed to favour a new worldwide nuclear development. (TEC). 8 refs., 4 figs., 6 tabs.

  6. Evaporation by mechanical vapor recompression. Technical progress report, September 1-December 31, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Iverson, C.H.; Coury, G.E.

    1979-01-01

    Progress to date in the development of a study of the application of the technologies of mechanical vapor recompression and falling film evaporators as applied to the beet sugar industry is reported. Progress is reported in the following areas: technical literature search and plant visitations of existing applications of VR/FFE.

  7. Power systems development facility. Quarterly technical progress report, July 1--September 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-31

    This quarterly technical progress report summarizes work completed during the Second Quarter of the Second Budget Period, July 1 through September 30, 1993, under the Department of Energy (DOE) Cooperative Agreement No. DE-FC21-90MC25140 entitled ``Hot Gas Cleanup Test Facility for Gasification and Pressurized Combustion.`` The objective of this project is to evaluate hot gas particle control technologies using coal-derived gas streams. This will entail the design, construction, installation, and use of a flexible test facility which can operate under realistic gasification and combustion conditions. The major particulate control device issues to be addressed include the integration of the particulate control devices into coal utilization systems, on-line cleaning techniques, chemical and thermal degradation of components, fatigue or structural failures, blinding, collection efficiency as a function of particle size, and scaleup of particulate control systems to commercial size. The conceptual design of the facility was extended to include a within scope, phased expansion of the existing Hot Gas Cleanup Test Facility Cooperative Agreement to also address systems integration issues of hot particulate removal in advanced coal-based power generation systems. This expansion included the consideration of the following modules at the test facility in addition to the existing Transport Reactor gas source and Hot Gas Cleanup Units: Carbonizer/Pressurized Circulating Fluidized Bed Gas Source. Hot Gas Cleanup Units to mate to all gas streams; Combustion Gas Turbine; and Fuel Cell and associated gas treatment. This expansion to the Hot Gas Cleanup Test Facility is herein referred to as the Power Systems Development Facility (PSDF). The major emphasis during this reporting period was continuing the detailed design of the facility.

  8. Technical Division quarterly progress report, April 1--June 30, 1977

    Energy Technology Data Exchange (ETDEWEB)

    Slansky, C.M.; Dickey, B.R.; Musgrave, B.C.; Rohde, K.L.

    1977-07-01

    Fuel Cycle Research and Development: Results are presented on the fluidized-bed calcination of high-level radioactive waste from reprocessing on the post treatment of the calcine, and on the removal of actinide elements from the waste prior to calcination. Other projects include the development of storage technology for /sup 85/Kr waste; a study of the hydrogen mordenite catalyzed reaction between NO/sub x/ and NH/sub 3/; the adsorption and storage of /sup 129/I on silver exchanged mordenite; physical properties, materials of construction, and unit operations studies on the evaporation of high-level waste; the behavior of volatile radionuclides during the combustion of HTGR graphite-based fuel; and the use of the uranium-ruthenium system in age-dating uranium ore bodies. Special Materials Production: The long-term management of defense waste from the ICPP covers postcalcination treatment of ICPP calcined waste; the removal of actinide elements from first-cycle raffinate; the retrieval and handling of calcined waste from ICPP storage vaults; and the preparation of the ''Defense Waste Document''. Process improvements are reported on the Fluorinel headend process for Zircaloy-clad fuels and on uranium accountability measurements. Other development results cover the process for recovering spent Rover fuel, buried pipeline transfer systems, support to the Waste Management Program, and effluent monitoring methods evaluation and development. Other Projects Supporting Energy Development: In this category are studies on nuclear materials security; application of a liquid-solid fluidized-bed heat exchanger to the recovery of geothermal heat; in-plant reactor source term measurements; burnup methods for fast breeder reactor fuels; absolute thermal fission yield measurements; analytical support to light water breeder reactor development; research on analytical methods; and the behavior of environmental species of iodine.

  9. LANL technical progress update for US HJPRR working group

    Energy Technology Data Exchange (ETDEWEB)

    Dombrowski, David E [Los Alamos National Laboratory

    2011-01-06

    The outline of this presentation is: (1) Collaboration on Master Alloy Melting; (2) Data for Safety Analysis, (3) HIP can development status, (4) Bond strength quality, (5) Plasma spraying results, and (6) Bare Rolling Larger Rolling Ingots. Significant near term progress has been made in five areas: (1) Collaboration on Master Alloy Melting; (2) HIP can development status; (3) Bond strength quality; (4) Plasma spraying results; and (5) Bare Rolling Larger Rolling Ingots. Significant progress is expected in the next month on several important areas: (1) Intrinsic bond strength of plasma sprayed Zr (2) Advanced Cleaning; (3) Residual Stress Collaboration with INL; and (4) Cost Metric Assessment.

  10. Proceedings of the sixth international conference on fluidized bed combustion. Volume II. Technical sessions

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-08-01

    The Sixth International Conference on Fluidized Bed Combustion was held April 9-11, 1980, at the Atlanta Hilton, Atlanta, Georgia. It was sponsored by the US Department of Energy, the Electric Power Research Institute, the US Environmental Protection Agency, and the Tennessee Valley Authority. The papers covered recent developments in atmospheric and pressurized fluidized-bed combustion, especially the design, operation and control of pilot and demonstration plants. The cleanup of combustion products and the erosion, corrosion and fouling of gas turbines was emphasized also. Fifty-five papers from Volume 2 of the proceedings have been entered individually into EDB and ERA; five papers had been entered previously from other sources. (LTN)

  11. Kinetics of lignite pyrolysis in fixed bed and entrained flow reactors. Technical report No. 17

    Energy Technology Data Exchange (ETDEWEB)

    Scaroni, A. W.; Walker, Jr., P. L.

    1979-08-01

    A laminar flow isothermal furnace has been constructed and used to study lignite pyrolysis in nitrogen at temperatures between 700/sup 0/ and 1000/sup 0/C. Particles of a Texas lignite (Darco Seam) between 41 and 201 microns in mean diameter, are found to flow down the furnace tube with velocities approximated by the summation of the gas plug-flow velocity and particle free-fall velocities. Some particle shrinkage and density changes occur during pyrolysis. Pyrolysis rate is particle size independent and increases with increase in temperature over the range of operating conditions. Ultimate yield of volatiles in the isothermal furnace, which is calculated from the linear relationship between weight loss and change in proximate volatile matter, is 66% of the original dry-ash-free coal and is particle size independent and relatively temperature independent. Ultimate yields of volatiles from fixed beds of pulverized coal are smaller than for dispersed particles of the same size. Proximate volatile matter for the lignite is, for example, 51% of the original dry-ash-free coal. Heating rates drop from about 10,000/sup 0/C/s in the isothermal furnace to about 20/sup 0/C/s in the proximate volatile matter test. Pyrolysis rates decrease and display particle size dependency in fixed beds. This implication of physical rate control is attributed to heat transfer limitations. It is proposed that pyrolysis rate and therefore residence time of volatiles in the fixed bed are important parameters affecting the preponderance of secondary char forming reactions.Also important is the total particle external surface area in the bed. Secondary char formation is considered responsible for yields of volatiles lower than the true volatile content of the lignite as measured in the isothermal furnace.

  12. Proceedings of the sixth international conference on fluidized bed combustion. Volume III. Technical sessions

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-08-01

    The Sixth International Conference on Fluidized Bed Combustion was held April 9-11, 1980, at the Atlanta Hilton, Atlanta, Georgia. It was sponsored by the US Department of Energy, the Electric Power Research Institute, the US Environmental Protection Agency, and the Tennessee Valley Authority. Forty-five papers from Vol. III of the proceedings have been entered individually into EDB and ERA. Two papers had been entered previously from other sources. (LTN)

  13. Technical progress report, 1 April-30 June 1981

    Energy Technology Data Exchange (ETDEWEB)

    None

    1981-01-01

    This report describes the technical accomplishments during the quarter ending June 1981, on the commercial nuclear waste management programs under the direction of the Office of Nuclear Waste Isolation (ONWI). The ONWI program is organized into 8 tasks entitled: systems, waste package, site, repository, regulatory and institutional, test facilities and excavations, land acquisition, and program management. Principal investigators in each of these areas have submitted summaries of quarterly highlights for inclusion in this report. Separate abstracts have been prepared for 5 of these tasks for inclusion in the Energy Data Base. (DMC)

  14. Quarterly technical progress report, February 1, 1996--April 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-28

    This report from the Amarillo National REsource Center for PLutonium provides research highlights and provides information regarding the public dissemination of information. The center is a a scientific resource for information regarding the issues of the storage, disposition, potential utilization and transport of plutonium, high explosives, and other hazardous materials generated from nuclear weapons dismantlement. The center responds to informational needs and interpretation of technical and scientific data raised by interested parties and advisory groups. Also, research efforts are carried out on remedial action programs and biological/agricultural studies.

  15. Environmental Research Division technical progress report: January 1986--October 1987

    Energy Technology Data Exchange (ETDEWEB)

    1988-07-01

    Technical process in the various research activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1986-1987. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Fundamental Molecular Physics and Chemistry, and Organic Geochemistry and Environmental Instrumentation Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter. Individual projects under each division are processed separately for the data bases.

  16. Development of a solar desiccant dehumidifier. Second technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Gunderson, M.E.; Hwang, K.C.; Railing, S.M.; Rousseau, J.

    1978-11-10

    Research and development of a solar desiccant dehumidifier featuring a rotary bed of granular silica gel and a rotary regenerator for air conditioning is described. The results of the system optimization studies are presented. The studies involved an extensive investigation of the energy saving potential and economic viability of the solar desiccant dehumidifier in different locations in the United States. Conventional electric vapor compression, and solar absorption and Rankine systems also were investigated for comparison. In general, it was found that the solar desiccant equipment, either by itself or in a hybrid system with an electric vapor compression air conditioner, is economically viable for all three locations considered. Substantial energy savings can be effected as well. Seal tests done at AiResearch to develop practical dynamic air seals are described. Leakage and friction tests were performed on a variety of material combinations and configurations. Dacron felt and silicone rubber were found to give an acceptable combination of leakage, friction, and cost characteristics. As part of the commercialization studies for the desiccant equipment, a questionnaire was sent to residential air conditioning equipment distributors. The results of the questionnaire are presented. The specifications and drawings for the 1.5-ton prototype are included. (WHK)

  17. Solar hot water space heating system. Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Van Dam, T

    1979-08-13

    A retrofit solar heating system was installed on Madison Hall at Jordan College, Cedar Springs, Michigan. The system provides heating and domestic water preheating for a campus dormitory. Freeze protection is provided by a draindown system. The building and solar system, construction progress, and design changes are described. Included in appendices are: condensate trap design, structural analysis, pictures of installation, operating instructions, maintenance instructions, and as-built drawings. (MHR)

  18. C-Mod Collaboration Informal Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    Kenneth W. Gentle

    2007-12-31

    The aims of the collaboration have not changed. A specific list of tasks was agreed upon during the Fall of 2006 in preparation for the 2007 C-Mod campaign by Earl Marmar, Head of the Alcator Project, Kenneth Gentle, Principal Investigator, and William Rowan, Collaboration Coordinator with the facilitation of Adam Rosenberg (DOE grant monitor for the collaboration). The activities follow the list of tasks and are discussed in this progress report.

  19. Monthly technical progress report, January 1, 1996 - January 28, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-24

    This is the January 1996 progress report contract DE-AC03-91SF18852 Radioisotope Thermoelectric Generators and Ancillary Activities, Cassini RTG Program. Included are discussions on the status of: (1) spacecraft integration and support, (2) engineering support, (3) safety, (4) qualified unicouple production, (5) ETG fabrication, Assembly, and Test, (6) ground support equipment, (7) RTG shipping and launch support, (8) designs, reviews, and mission applications, (9) project management, and (10) CAGO acquisition.

  20. Technical Progress Has Positive,Differentiated Effects on Energy Efficiency of Chinese Industries

    Institute of Scientific and Technical Information of China (English)

    李廉水; 周勇

    2007-01-01

    The rebound effects of technological advancement on energy consumption make it very complicated to measure the impact of technological advancement on energy efficiency.This article,taking 35 industries as samples,utilizes the non-parameter DEA-Malmquist productivity approach to subcategorise technological advancement into three parts:science-technological(sci-tech)progress,pure technical efficiency and efficiency of scale.The panel technique is then used to work out each subcategory’s contribution to energy efficiency individually.Findings show that technological efficiency (calculated by multiplying the results of pure technical efficiency and scale efficiency)is the principal factor in the improvement of energy efficiency while the contribution from sci-tech progress is comparatively less.Overtime,however,the effect of sci-tech progress is gradually heightened while the effect of technical efficiency slowly diminishes.

  1. Development of a solar desiccant dehumidifier. Volume 1. Summary. Volume 2. Detailed technical information. Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Gunderson, M.E.; Hwang, K.C.; Railing, S.M.

    1978-03-31

    Research and development work aimed at the development of a solar desiccant dehumidifier is described in detail. The system features a rotary bed of granular silica gel and a rotary regenerator. The dehumidifier can be used for air conditioning through adiabatic saturation of the process airstream. Detailed technical information is presented in the appendices: (A) management, (B) review of the literature: state-of-the-art survey and SERI meeting, (C) review of the literature: adsorbent survey, (D) design requirements and evaluation criteria, (E) design requirements and evaluation criteria, single-family house model, (F) design requirements and evaluation criteria, economic model, (G) design requirements and evaluation criteria: conventional system models for comparison, (H) candidate cooling subsystems, (I) subsystem computer model, (J) subsystem performance map, and (K) subsystem preliminary design. (WHK)

  2. Technical and economic assessment of fluidized-bed-augmented compressed-air energy-storage system. Volume 1: Executive summary

    Science.gov (United States)

    Giramonti, A. J.; Lessard, R. D.; Merrick, D.; Hobson, M. J.

    1981-09-01

    An energy storage system for electric utility peak load applications is a modified gas turbine power system utilizing underground storage of very high pressure air. The compressed air energy storage (CAES) concept involves using off peak electricity generated from indigenous coal or nuclear sources to compress air, storing the air in large underground facilities, and withdrawing the air during peak load periods when it would be heated by combustion and expanded through gas turbines to generate power. The attractiveness of the CAES concept is based upon its potential to supply competitively priced peaking energy, to reduce peak load power plant dependence on petroleum based fuels, and to provide a means for leveling the utility system load demand. Therefore, a technical and economic assessment of coal fired fluidized bed combustor/compressed air energy storage systems was performed and is described.

  3. Electronic refrigerant leak detector. Quarterly technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Talamas, E. Jr.

    1998-10-15

    The project comprises three main tasks. They are (1) Develop, design, and fabricate sensors, (2) Develop, design, and fabricate test instruments, (3) Testing and data analysis. The milestone includes 17 sub-tasks for the 52-weeks project period, starting on May 1, 1998 and ending on April 30, 1999. As stated in the Application for Federal Assistance, Micronic intended to relocate to a new office by June of 1998. This decision was delayed, since the first partial payment was transferred on August 12, 1998. Micronic plans to relocate this November. A second Provisional Application for a US patent has been filed. Progress made during this period is reported.

  4. Technical and economic assessment of fluidized bed augmented compressed air energy-storage system. Volume II. Introduction and technology assessment

    Energy Technology Data Exchange (ETDEWEB)

    Giramonti, A.J.; Lessard, R.D.; Merrick, D.; Hobson, M.J.

    1981-09-01

    The results are described of a study subcontracted by PNL to the United Technologies Research Center on the engineering feasibility and economics of a CAES concept which uses a coal fired, fluidized bed combustor (FBC) to heat the air being returned from storage during the power production cycle. By burning coal instead of fuel oil, the CAES/FBC concept can completely eliminate the dependence of compressed air energy storage on petroleum fuels. The results of this assessment effort are presented in three volumes. Volume II presents a discussion of program background and an in-depth coverage of both fluid bed combustion and turbomachinery technology pertinent to their application in a CAES power plant system. The CAES/FBC concept appears technically feasible and economically competitive with conventional CAES. However, significant advancement is required in FBC technology before serious commercial commitment to CAES/FBC can be realized. At present, other elements of DOE, industrial groups, and other countries are performing the required R and D for advancement of FBC technology. The CAES/FBC will be reevaluated at a later date when FBC technology has matured and many of the concerns now plaguing FBC are resolved. (LCL)

  5. Texas Experimental Tokamak. Technical progress report, April 1990--April 1993

    Energy Technology Data Exchange (ETDEWEB)

    Wootton, A.J.

    1993-04-01

    This progress report covers the period from November 1, 1990 to April 30, 1993. During that period, TEXT was operated as a circular tokamak with a material limiter. It was devoted to the study of basic plasma physics, in particular to study of fluctuations, turbulence, and transport. The purpose is to operate and maintain TEXT Upgrade as a complete facility for applied tokamak physics, specifically to conduct a research program under the following main headings: (1) to elucidate the mechanisms of working gas, impurity, and thermal transport in tokamaks, in particular to understand the role of turbulence; (2) to study physics of the edge plasma, in particular the turbulence; (3) to study the physics or resonant magnetic fields (ergodic magnetic divertors, intra island pumping); and (4) to study the physics of electron cyclotron heating (ECRH). Results of studies in each of these areas are reported.

  6. TECHNICAL TRAINING SEMINAR: High Temperature Superconductors: Progress and Issues

    CERN Multimedia

    Davide Vitè

    2002-01-01

    Monday 24 June from 14:30 to 15:30 - Training Centre Auditorium - bldg. 593-11 High Temperature Superconductors: Progress and Issues Prof. Jan Evetts / UNIVERSITY OF CAMBRIDGE, Department of Materials Science and Metallurgy, UK Grappling with grain boundaries: Current transport processes in granular High Temperature Superconductors (HTS) The development of High Temperature Superconductors, seen from a materials scientist's point of view, is relevant to the superconductivity community at CERN: their possible high current applications can include high performance magnets for future accelerators. There is an urgent need to develop a quantitative description of HTS conductors in terms of their complex anisotropy, inhomogeneity and dimensionality. This is essential both for the practical specification of a conductor and for charting routes to conductor optimisation. The critical current, the n-value, dissipation and quenching characteristics are amongst most important parameters that make up an engineering specifi...

  7. MARKET ASSESSMENT AND TECHNICAL FEASIBILITY STUDY OF PRESSURIZED FLUIDIZED BED COMBUSTION ASH USE

    Energy Technology Data Exchange (ETDEWEB)

    A.E. Bland; T.H. Brown

    1997-04-01

    Western Research Institute, in conjunction with the Electric Power Research Institute, Foster Wheeler International, Inc. and the US Department of Energy, has undertaken a research and demonstration program designed to examine the market potential and the technical feasibility of ash use options for PFBC ashes. Ashes from the Foster Wheeler Energia Oy pilot-scale circulating PFBC tests in Karhula, Finland, combusting (1) low-sulfur subbituminous and (2) high-sulfur bituminous coal, and ash from the AEP's high-sulfur bituminous coal-fired bubbling PFBC in Brilliant, Ohio, were evaluated in laboratory and pilot-scale ash use testing at WR1. The technical feasibility study examined the use of PFBC ash in construction-related applications, including its use as a cementing material in concrete and use in cement manufacturing, fill and embankment materials, soil stabilization agent, and use in synthetic aggregate production. Testing was also conducted to determine the technical feasibility of PFBC ash as a soil amendment for acidic and sodic problem soils and spoils encountered in agricultural and reclamation applications. The results of the technical feasibility testing indicated the following conclusions. PFBC ash does not meet the chemical requirements as a pozzolan for cement replacement. However, it does appear that potential may exist for its use in cement production as a pozzolan and/or as a set retardant. PFBC ash shows relatively high strength development, low expansion, and low permeability properties that make its use in fills and embankments promising. Testing has also indicated that PFBC ash, when mixed with low amounts of lime, develops high strengths, suitable for soil stabilization applications and synthetic aggregate production. Synthetic aggregate produced from PFBC ash is capable of meeting ASTM/AASHTO specifications for many construction applications. The residual calcium carbonate and calcium sulfate in the PFE3C ash has been shown to be of

  8. Texas Experimental Tokamak, a plasma research facility: Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Wootton, A.J.

    1995-08-01

    In the year just past, the authors made major progress in understanding turbulence and transport in both core and edge. Development of the capability for turbulence measurements throughout the poloidal cross section and intelligent consideration of the observed asymmetries, played a critical role in this work. In their confinement studies, a limited plasma with strong, H-mode-like characteristics serendipitously appeared and received extensive study though a diverted H-mode remains elusive. In the plasma edge, they appear to be close to isolating a turbulence drive mechanism. These are major advances of benefit to the community at large, and they followed from incremental improvements in diagnostics, in the interpretation of the diagnostics, and in TEXT itself. Their general philosophy is that the understanding of plasma physics must be part of any intelligent fusion program, and that basic experimental research is the most important part of any such program. The work here demonstrates a continuing dedication to the problems of plasma transport which continue to plague the community and are an impediment to the design of future devices. They expect to show here that they approach this problem consistently, systematically, and effectively.

  9. Technical Assistance Paper: Third-Grade Student Progression. DPS: 2013-56

    Science.gov (United States)

    Florida Department of Education, 2013

    2013-01-01

    The purpose of this Technical Assistance Paper (TAP) is to provide school districts with updates and changes relative to third-grade student progression policies, including information on alternative assessments, promotion criteria and resources. This paper provides: (1) General Information; (2) Student Portfolios for Third-Grade Students; (3)…

  10. Amarillo National Resource Center for Plutonium. Quarterly technical progress report, May 1--July 31, 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    Progress is reported on research projects related to the following: Electronic resource library; Environment, safety, and health; Communication, education, training, and community involvement; Nuclear and other materials; and Reporting, evaluation, monitoring, and administration. Technical studies investigate remedial action of high explosives-contaminated lands, radioactive waste management, nondestructive assay methods, and plutonium processing, handling, and storage.

  11. FAST FLUX TEST FACILITY MONTHLY INFORMAL TECHNICAL PROGRESS REPORT MAY 1969

    Energy Technology Data Exchange (ETDEWEB)

    Astley, E. R.; Cabell, C. P.

    1969-06-06

    This report was prepared by Battelle-Northwest under Contract No. AT(45-1)-1830 for the Atomic Energy Commission, Division of Reactor Development and Technology, to summarize technical progress made in the Fast Flux Test Facility Program during May 1969 .

  12. FAST FLUX TEST FACILITY MONTHLY INFORMAL TECHNICAL PROGRESS REPORT SEPTEMBER 1969

    Energy Technology Data Exchange (ETDEWEB)

    Astely, E. R.; Cabell, C. P.

    1969-10-07

    This report was prepared by Battelle-Northwest under Contract No. AT(45-1)-1830 for the Atomic Energy Commission, Division of Reactor Development and Technology, to summarize technical progress made in the Fast Flux Test Facility Program during September 1969.

  13. Technical Adequacy and Acceptability of Curriculum-Based Measurement and the Measures of Academic Progress

    Science.gov (United States)

    January, Stacy-Ann A.; Ardoin, Scott P.

    2015-01-01

    Curriculum-based measurement in reading (CBM-R) and the Measures of Academic Progress (MAP) are assessment tools widely employed for universal screening in schools. Although a large body of research supports the validity of CBM-R, limited empirical evidence exists supporting the technical adequacy of MAP or the acceptability of either measure for…

  14. FAST FLUX TEST FACILITY MONTHLY INFORMAL TECHNICAL PROGRESS REPORT FEBRUARY 1969

    Energy Technology Data Exchange (ETDEWEB)

    Astley, E. R.

    1969-03-07

    This report was prepared by Battelle-Northwest under Contract No. AT (45-1)-1830 for the Atomic Energy Commission, Division of Reactor Development and Technology, to summarize technical progress made in the Fast Flux Test Facility Program during February 1969.

  15. Cassini RTG Program. Monthly technical progress report, 27 November--31 December 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-01-24

    This monthly technical progress report provided information on the following tasks: spacecraft integration and liaison; engineering support; safety analysis; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment (GSE); RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, and reliability, and contractor acquired government owned (CAGO) property acquisition.

  16. Development of superior asphalt recycling agency: Phase 1, Technical feasibility. Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Bullin, J.A.; Glover, C.J.; Davison, R.R.; Lin, Moon-Sun; Chaffin, J.; Liu, Meng; Eckhardt, C.

    1996-04-01

    About every 12 years, asphalt roads must be reworked, and this is usually done by placing thick layers (hot-mix overlays) of new material on top of failed material, resulting in considerable waste of material and use of new asphalt binder. A good recycling agent is needed, not only to reduce the viscosity of the aged material but also to restore compatibility. Objective is to establish the technical feasibility (Phase I) of determining the specifications and operating parameters for producing high quality recycling agents which will allow most/all the old asphalt-based road material to be recycled. It is expected that supercritical fractionation can be used. The advanced road aging simulation procedure will be used to study aging of blends of old asphalt and recycling agents.

  17. Professional technical support services for the Mining Equipment Test Facility. First annual technical progress report, April 14-September 30, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Garson, R C

    1981-10-01

    The Department of Energy recently began the operation of its Mining Equipment Test Facility. One component at that facility is the highly sophisticated Mine Roof Simulator (MRS) for research and development of roof support equipment. Because of its previous experience, the University of Pittsburgh was contracted to assist the Facilities Manager by providing professional technical support services, principally for the MRS. This technical progress report briefly describes the services provided during the reporting period and planned for the next period. No significant technical disclosures of interest to those not associated with the MRS are contained herein. One of the four units of the US government-owned METF is the Mine Roof Simulator. This unique $10 million test facility was designed to simulate underground mine roof loads and motions. The MRS is a hybrid, analog-digital, computer-controlled, closed-loop, electro-hydraulic, research device capable of applying either loads or displacements in the vertical and one horizontal axis. Its vertical capacity of 3,000,000 pounds can be applied over its 20 by 20 foot active test area. The horizontal load capacity is 1,600,000 pounds. It can simulate coal seam heights of up to 16 feet. Automatic data acquisition and real time display are provided. The most modern, sophisticated technology was used in its design and construction.

  18. PREFACE: Scientific and Technical Challenges in the Well Drilling Progress

    Science.gov (United States)

    2015-02-01

    departments - Technologies in Mineral Exploration and Technologies in Mineral Exploration were merged into one department. In 2003 the newly merged Department of Drilling was established within the Institute of Petroleum Engineering, now the Institute of Natural Resources and is located in Building № 6 where it began its life. During these 60 years more than 3000 specialists have graduated the Department of Drilling, many whom are highly-qualified and dedicated professionals. There is no doubt that this Conference involved comprehensive advanced engineering problems in drilling and issues on relevant personnel training. It is extremely important to understand how the 60-year progress and contribution in the field of drilling has left its trace in the history of this Department; and, that, now, it is necessary to move further and seek new and new horizons in drilling.

  19. Appraisement on Contributive Ratio of Scientific and Technical Progresses in Milk Productive Enterprises by Model C2GS2

    Institute of Scientific and Technical Information of China (English)

    SUN Futian; SUN Liqun; YANG Guanglin

    2008-01-01

    Scientific and technical progress has been the driving forces of enterprises development. Milk productive enterprises are developing faster and growing better. It is very important to measure the contributive ratio of scientific and technical progress in milk productive enterprises. And the appraisement could help to develop milk productive enterprises. The model C2GS2 was established to appraise the contributive ratio of scientific and technical progress in milk productive enterprises in the research. And the appraisement on the contributive ratio of scientific and technical progress in milk productive enterprises was made by the model. In the results of appraisement, science and technology play a main role in milk productive enterprises. It is shown that our milk productive enterprises are developed by scientific and technical progress while not by input of productive factors.

  20. Examining the Technical Adequacy of Second-Grade Reading Comprehension Measures in a Progress Monitoring Assessment System. Technical Report # 08-08

    Science.gov (United States)

    Alonzo, Julie; Liu, Kimy; Tindal, Gerald

    2008-01-01

    This technical report describes the development of reading comprehension assessments designed for use as progress monitoring measures appropriate for 2nd Grade students. The creation, piloting, and technical adequacy of the measures are presented. The following are appended: (1) Item Specifications for MC [Multiple Choice] Comprehension - Passage…

  1. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 1. Geological environment of Japan

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, the part 1 of the progress report, describes first in detail the role of geological environment in high-level radioactive wastes disposal, the features of Japanese geological environment, and programs to proceed the investigation in geological environment. The following chapter summarizes scientific basis for possible existence of stable geological environment, stable for a long period needed for the HLW disposal in Japan including such natural phenomena as volcano and faults. The results of the investigation of the characteristics of bed-rocks and groundwater are presented. These are important for multiple barrier system construction of deep geological disposal. The report furthermore describes the present status of technical and methodological progress in investigating geological environment and finally on the results of natural analog study in Tono uranium deposits area. (Ohno, S.)

  2. Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 4

    Energy Technology Data Exchange (ETDEWEB)

    Ulm, Franz-Josef

    2000-06-30

    OAK-B135 Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 4. The analysis of the effect of cracks on the acceleration of the calcium leaching process of cement-based materials has been pursued. During the last period (Technical Progress Report No 3), we have introduced a modeling accounting for the high diffusivity of fractures in comparison with the weak solid material diffusivity. It has been shown through dimensional and asymptotic analysis that small fractures do not significantly accelerate the material aging process. This important result for the overall structural aging kinetics of containment structure has been developed in a paper submitted to the international journal ''Transport in Porous Media''.

  3. Cassini RTG Program monthly technical progress report, July 28--August 24, 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-24

    The technical progress achieved during this period is described. This report is organized by program task structure: (1) spacecraft and integration liaison; (2) engineering support; (3) safety; (4) qualified unicouple production; (5) ETG fabrication, assembly, and test; (6) ground support equipment (GSE); (7) RTG shipping and launch support; (8) designs, reviews, and mission applications; (9) project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and CAGO maintenance and repair; and (10) CAGO acquisition (capital funds).

  4. Decontamination Systems Information and Research Program. Quarterly technical progress report, January 1--March 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-01

    West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Reports on a quarterly basis. This report comprises the first Quarterly Technical Progress Report for Year 2 of the Agreement. This report reflects the progress and/or efforts performed on the sixteen (16) technical projects encompassed by the Year 2 Agreement for the period of January 1 through March 31, 1994. In situ bioremediation of chlorinated organic solvents; Microbial enrichment for enhancing in-situ biodegradation of hazardous organic wastes; Treatment of volatile organic compounds (VOCs) using biofilters; Drain-enhanced soil flushing (DESF) for organic contaminants removal; Chemical destruction of chlorinated organic compounds; Remediation of hazardous sites with steam reforming; Soil decontamination with a packed flotation column; Use of granular activated carbon columns for the simultaneous removal of organics, heavy metals, and radionuclides; Monolayer and multilayer self-assembled polyion films for gas-phase chemical sensors; Compact mercuric iodide detector technology development; Evaluation of IR and mass spectrometric techniques for on-site monitoring of volatile organic compounds; A systematic database of the state of hazardous waste clean-up technologies; Dust control methods for insitu nuclear and hazardous waste handling; Winfield Lock and Dam remediation; and Socio-economic assessment of alternative environmental restoration technologies.

  5. TERTIARY ECONOMIC ACTIVITIES UNDER THE IMPACT OF SCIENTIFIC AND TECHNICAL PROGRESS IN ROMANIA

    Directory of Open Access Journals (Sweden)

    PAUL-BOGDAN ZAMFIR

    2015-06-01

    Full Text Available The scientific and technical progress put its mark in a different manner on all activities that occur within contemporary economy and it was present in the entire evolution of human society, but its implications and effects were never so strong and extensive. There is no area of activity in which progress not to interfere, both as important mutations that they are happening in the all area of production factors, as well as the place and role of the human factor in the deployment of production processes. In the current period the progress has exceeded certain human limits, operating in other areas which until more now it seems unattainable by the achievements of new technology. In this paradigm are successfully integrated tertiary activities in which the scientific and technical progress entered with great difficulty.Nowadays we are witnessing spectacular evolutions whether we talk about movement of goods, education, research, health, transportation, arts and culture, etc. The purpose of this paper is to determine the degree in which scientific and technical progress. In this paper we proposed to determine the level in which the scientific and technical progress, had a decisive impact on the development of the tertiary sector in general and in Romania in particular , we shall specify which are the economic tertiary activities that adapt fast to new changes occurred in the system of informational society. In this context we have to mention the systems of intelligent transport, electronic governance, medical system based on ICT online educational systems, as a possible response of the tertiary sector to the adaptation of technological progress benefits. In the first part of this paper we focused on the conceptual delimitation of scientific concepts at which we refer often such as: technological progress and innovative services which inevitably determine the evolution of tertiary sector under the impact of new modern technologies. On this background

  6. Upgrade of deep bed filtration with activated carbon dosage for compact micropollutant removal from wastewater in technical scale.

    Science.gov (United States)

    Löwenberg, Jonas; Zenker, Armin; Krahnstöver, Thérèse; Boehler, Marc; Baggenstos, Martin; Koch, Gerhard; Wintgens, Thomas

    2016-05-01

    The removal of micropollutants from drinking and wastewater by powdered activated carbon (PAC) adsorption has received considerable attention in research over the past decade with various separation options having been investigated. With Switzerland as the first country in the world having adopted a new legislation, which forces about 100 wastewater treatment plants to be upgraded for the removal of organic micropollutants from municipal wastewater, the topic has reached practical relevance. In this study, the process combination of powdered activated carbon (PAC) adsorption and deep bed filtration (DBF) for advanced municipal wastewater treatment was investigated over an extended period exceeding one year of operation in technical scale. The study aimed to determine optimum process conditions to achieve sufficient micropollutant removal in agreement with the new Swiss Water Ordinance under most economic process design. It was shown that the addition of PAC and Fe(3+) as combined coagulation and flocculation agent improved effluent water quality with respect to dissolved organic pollutants as well as total suspended solids (TSS), turbidity and PO4-P concentration in comparison to a DBF operated without the addition of PAC and Fe(3+). Sufficient micropollutant (MP) removal of around 80% was achieved at PAC dosages of 10 mg/L revealing that PAC retained in the filter bed maintained considerable adsorption capacity. In the investigated process combination the contact reactor serves for adsorption as well as for flocculation and allowed for small hydraulic retention times of minimum 10 min while maintaining sufficient MP removal. The flocculation of two different PAC types was shown to be fully concluded after 10-15 min, which determined the flocculation reactor size while both PAC types proved suitable for the application in combination with DBF and showed no significant differences in MP removal. Finally, the capping of PAC dosage during rain water periods, which

  7. Hot gas cleanup test facility for gasification and pressurized combustion. Quarterly technical progress report, January 1--March 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-12-01

    This quarterly technical progress report summarizes work completed during the Sixth Quarter of the First Budget Period, January 1 through March 31, 1992, under the Department of Energy (DOE) Cooperative Agreement No. DE-FC21-90MC25140 entitled ``Hot Gas Cleanup Test Facility for Gasification and Pressurized Combustion.`` The objective of this project is to evaluate hot gas particle control technologies using coal-derived gas streams. The major emphasis during this reporting period was expanding the test facility to address system integration issues of hot particulate removal in advanced power generation systems. The conceptual design of the facility was extended to include additional modules for the expansion of the test facility, which is referred to as the Power Systems Development Facility (PSOF). A letter agreement was negotiated between Southern Company Services (SCS) and Foster Wheeler (FW) for the conceptual design of the Advanced Pressurized Fluid-Bed Combustion (APFBC)/Topping Combustor/Gas Turbine System to be added to the facility. The expanded conceptual design also included modifications to the existing conceptual design for the Hot Gas Cleanup Test Facility (HGCTF), facility layout and balance of plant design for the PSOF. Southern Research Institute (SRI) began investigating the sampling requirements for the expanded facility and assisted SCS in contacting Particulate Control Device (PCD) vendors for additional information. SCS also contacted the Electric Power Research Institute (EPRI) and two molten carbonate fuel cell vendors for input on the fuel cell module for the PSDF.

  8. Study of ebullated bed fluid dynamics. Final progress report, September 1980-July 1983

    Energy Technology Data Exchange (ETDEWEB)

    Schaefer, R.J.; Rundell, D.N.; Shou, J.K.

    1983-07-01

    The fluid dynamics occurring in HRI's H-coal process development unit coal liquefaction reactor during Run PDU-10 were measured and compared with Amoco Oil cold-flow fluidization results. It was found that catalyst bed expansions and gas holdups are higher in the PDU than those observed in the cold-flow tests for slurries having the same nominal viscosity. Comparison of PDU results with cold-flow results shows that the bulk of the operating reactor gas flow lies in the ideal bubbly regime. It also appears that the gas bubbles in these PDU tests are rising quite slowly. Only two of the operating points in our test program on the PDU were found to lie in the churn turbulent regime. Existence of churn turbulent behavior during these two experiments is consistent with trends observed in earlier cold-flow experiments. Two- and three-phase fluidization experiments were carried out in Amoco's cold-flow fluid dynamics unit. The data base now includes fluidization results for coal char/kerosene slurry concentrations of 4.0, 9.8, and 20.7 vol% in addition to the 15.5 and 17.8 vol% data from our earlier work. Both HDS-2A and Amocat-1A catalysts were used in the tests. Bed expansion is primarily a function of slurry velocity, with gas velocity having only a weak effect. Bed contractions have been observed in some cases at sufficiently high gas velocity. Gas and liquid holdups were found to be uniform across the cross-section of the Amoco cold-flow fluid dynamics pilot plant. A viscometer was adapted for measurement of the viscosity of coal slurries at high temperature and pressure. Based on experiments carried out in the Amoco cold-flow unit, a significant degree of backmixing was found to occur in the H-Coal system. 70 references, 93 figures, 32 tables.

  9. Pressurized fluidized-bed hydroretorting of Eastern oil shales. Progress report, December 1991--February 1992

    Energy Technology Data Exchange (ETDEWEB)

    Lau, F.S.; Mensinger, M.C.; Roberts, M.J.; Rue, D.M.

    1992-03-01

    The objective is to perform the research necessary to develop the pressurized fluidized-bed hydroretorting (PFH) process for producing oil from Easter oil shales. The program also incorporates research on technologies in areas such as raw shale preparation, beneficiation, product separation, and waste disposal that have the potential of improving the economics and/or environmental acceptability of recovering oil from oil shales using the PFH process. Accomplishments for this period are presented for the following tasks: Testing of Process Improvement Concepts; Beneficiation Research; Operation of PFH on Beneficiated Shale; Environmental Data and Mitigation Analyses; Sample Procurement, Preparation, and Characterization; and Project Management and Reporting. 24 figs., 19 tabs. (AT)

  10. Decontamination Systems Information and Research Program. Quarterly technical progress report, January 1--March 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-04-01

    This reports reports the progress/efforts performed on six technical projects: 1. systematic assessment of the state of hazardous waste clean-up technologies; 2. site remediation technologies (SRT):drain- enhanced soil flushing for organic contaminants removal; 3. SRT: in situ bio-remediation of organic contaminants; 4. excavation systems for hazardous waste sites: dust control methods for in-situ nuclear waste handling; 5. chemical destruction of polychlorinated biphenyls; and 6. development of organic sensors: monolayer and multilayer self-assembled films for chemical sensors.

  11. Kaldor’s ‘technical progress function’ and Verdoorn’s law revisited

    OpenAIRE

    McCombie, John S. L.; Spreafico, Marta R. M.

    2015-01-01

    This is the accepted manuscript of a paper published in the Cambridge Journal of Economics (McCombie JSL, Spreafico MRM, Cambridge Journal of Economics, 2015, doi:10.1093/cje/bev030). The final version is available at http://dx.doi.org/10.1093/cje/bev030 Kaldor put forward his technical progress function as an alternative to the neoclassical aggregate production function. It is shown that Verdoorn?s law is its empirical counterpart, although allowing for increasing returns to scale. Howeve...

  12. Monthly technical progress report, 29 January 1996--25 Februray 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-04-01

    This report discusses the technical progress made on the radioisotope thermoelectric generators and ancillary activities for the Cassini space probe mission to the planet Saturn. The probe is designated for launch in October of 1997. This report covers the project reporting period from 29 January 1996 through 25 February 1996. The report is organized by program task structure and includes activities for: spacecraft integration and liason; engineering support; safety; qualified unicouple production; ETG fabrication, assembly, and testing; RTG shipping and launch support; designs, reviews and mission applications; quality assurance, reliability and contract changes; and CAGO acquisition.

  13. Biomass power for rural development. Technical progress report, April 1, 1997--June 30, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Neuhauser, E.

    1997-08-01

    Detailed task progress reports and schedules are provided for the DOE/USDA sponsored Biomass Power for Rural Development project. The focus of the project is on developing commercial energy crops for power generation by the year 2000. The New York based Salix Consortium project is a multi-partner endeavor, implemented in three stages. Phase-I, Final Design and Project Development, will conclude with the preparation of construction and/or operating permits, feedstock production plans, and contracts ready for signature. Field trials of willow (Salix) have been initiated at several locations in New York (Tully, Lockport, King Ferry, La Fayette, Massena, and Himrod) and co-firing tests are underway at Greenidge Station (NYSEG) and Dunkirk Station (NMPC). Phase-H of the project will focus on scale-up of willow crop acreage, construction of co-firing facilities at Dunkirk Station (NMPC), and final modifications for Greenidge Station. Cofiring willow is also under consideration for GPU`s Seward Station where testing is under way. There will be an evaluation of the energy crop as part of the gasification trials occurring at BED`s McNeill power station. Phase-III will represent fullscale commercialization of the energy crop and power generation on a sustainable basis.

  14. Advancement of flash hydrogasification. Quarterly technical progress report, January-March 1984

    Energy Technology Data Exchange (ETDEWEB)

    Falk, A.Y.

    1984-06-25

    This first quarterly report documents technical progress during the period 31 December 1983 through 30 March 1984. The technical effort is 17 months in duration and is divided into two major technical tasks: Task VII, Hardware Fabrication and PDU Modifications, and Task VIII, Performance Testing. The design of test hardware and process development unit modifications had been previously completed as part of Task VI of the current contract. Task VII involves the fabrication of test hardware and modification of an existing 1-ton/h hydroliquefaction PDU at Rockwell's facilities for use as a hydrogasifier test facility. During this report period, fabrication of the test hardware and modifications to the PDU were initiated. Test hardware fabrication is now approximately 80% complete and should be completed by the end of May 1984. PDU modifications are progressing well and should be completed by the end of June 1984. The completed test hardware fabrication and PDU modifications will allow the conduct of short duration (1 to 2 h) hydrogasification tests along with preburner assembly performance evaluation tests in order to fulfill the test program objectives. Separate supplies of hydrogen, oxygen, methane, carbon monoxide, and water (for steam generation) are provided for this purpose. The modified facility is designed to accommodate both 10- and 20-ft-long hydrogasifier reactors so that residence times will be in the range of 2 to 6 s when coal is fed at a nominal 1/2 ton/h into reactors at 1000 psia pressure. Provisions are being made for real-time analysis of the product gases using an on-line gas chromatograph system. Test planning was the only Task VIII effort active during this report period. An initial (preliminary) test matrix has been defined. Preparation of a data analysis plan is underway, and data reduction programs are being programmed. 17 references, 25 figures, 6 tables.

  15. Technical notes for the conceptual design for an atmospheric fluidized-bed direct combustion power generating plant. [570 MWe plant

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-04-01

    The design, arrangement, thermodynamics, and economics of a 592 MW(e) (nominal gross) electric power generating plant equipped with a Babcock and Wilcox Company (B and W) atmospheric fluidized bed (AFB) boiler are described. Information is included on capital and operating costs, process systems, electrical systems, control and instrumentation, and environmental systems. This document represents a portion of an overall report describing the conceptual designs of two atmospheric fluidized bed boilers and balance of plants for the generation of electric power and the analysis and comparison of these conceptual designs to a conventional pulverized coal-fired electric power generation plant equipped with a wet limestone flue gas desulfurization system.

  16. Technical notes for the conceptual design for an atmospheric fluidized-bed direct combustion power generating plant. [570 MWe plant

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-04-01

    The design, arrangement, thermodynamics, and economics of a 578 MW(e) (nominal gross) electric power generating plant equipped with a Foster Wheeler Energy Corporation (FWEC) atmospheric fluidized bed (AFB) boiler are described. Information is included on capital and operating costs, process systems, electrical systems, control and instrumentation, and environmental systems. This document represents a portion of an overall report describing the conceptual designs of two atmospheric fluidized bed boilers and balance of plants for the generation of electric power and the analysis and comparison of these conceptual designs to a conventional pulverized coal-fired electric power generation plant equipped with a wet limestone flue gas desulfurization system.

  17. Development of the instrumentation and modeling for heat transfer characteristics in CFBC. Technical progress report No. 2, April 1, 1996--September 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Seong W.

    1996-11-01

    This technical report summarizes the research conducted and progress achieved during the period of April 1, 1996 to September 30, 1996. Auxiliary subsystems tests of the circulating fluidized bed were conducted and included the characteristics of a regenerative blower, a gas distributor, and a cyclone. When the air flow rate increases, the pressure at the blower outlet is decreased. The air flow rate in the riser is a function of the pressure in the wind box. The cyclone pressure drop and gas distributor pressure drop are functions of the primary air flow rate input. The higher gas pressure drop indicates primary air in the riser column with a uniform superficial velocity. The CFB primary test was conducted using glass beads as one of the CFB bed materials. Three typical tests with different sizes of glass were conducted. The pressure sensor data acquisition system was developed for the systematic instrumentation of flow measurements in the CFB system. Two types of sensors were used, a single pressure sensor, and a differential pressure sensor, respectively. The software used to control the analog/digital board was Paragon 500. The CFB experimental studies for hydrodynamics will be continued with the improved data acquisition system.

  18. Power systems development facility. Quarterly technical progress report, January 1, 1994--March 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-01

    This quarterly technical progress report summarizes work completed during the last quarter of the Second Budget Period, January 1 through March 31, 1994, entitled {open_quotes}Hot Gas Cleanup Test Facility for Gasification and Pressurized Combustion.{close_quotes} The objective of this project is to evaluate hot gas particulate control technologies using coal-derived gas streams. This will entail the design, construction, installation, and use of a flexible test facility which can operate under realistic gasification and combustion conditions. The major particulate control device issues to be addressed include the integration of the particulate control devices into coal utilization systems, on-line cleaning techniques, chemical and thermal degradation of components, fatigue or structural failures, blinding, collection efficiency as a function of particle size, and scale-up of particulate control systems to commercial size.

  19. Quarterly technical progress report, October-December 1982 on Energy Conversion Research and Development Programs

    Energy Technology Data Exchange (ETDEWEB)

    1983-10-01

    In this quarterly technical progress report, UTSI reports on the continued design work for the low mass flow train superheater. The detailed design of this component continued and the overall arrangement drawing for the superheater and air heater was finalized. The air heater procurement reached the point of contract award, but the actual purchase order award was held up pending receipt of additional funding from the Department of Energy. Testing activity reported includes two additional tests in the LMF1C series, which concludes this test series. Test data are presented, along with preliminary analyses for the combustor, nozzle, diagnostic channel, diffuser, radiant furnace/secondary combustor and Materials Test Module. In addition to the nitrogen oxide test measurements, corrosion and erosion rates for the boiler tube specimens and the materials test module are reported.

  20. MHD Integrated Topping Cycle Project. Seventeenth quarterly technical progress report, August 1, 1991--October 31, 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-07-01

    This seventeenth quarterly technical progress report of the MHD Integrated Topping Cycle Project presents the accomplishments during the period August 1, 1991 to October 31, 1991. Manufacturing of the prototypical combustor pressure shell has been completed including leak, proof, and assembly fit checking. Manufacturing of forty-five cooling panels was also completed including leak, proof, and flow testing. All precombustor internal components (combustion can baffle and swirl box) were received and checked, and integration of the components was initiated. A decision was made regarding the primary and backup designs for the 1A4 channel. The assembly of the channel related prototypical hardware continued. The cathode wall electrical wiring is now complete. The mechanical design of the diffuser has been completed.

  1. MHD air heater technology development. Annual technical progress report, January 1, 1980-December 31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    None

    1981-03-01

    Progress on the technology development of the directly-fired high temperature air heater (HTAH) for MHD power plants is described in detail. The objective of task 1 is to continue development of ceramic materials technology for the directly-fired HTAH. The objectives of task 2 are to demonstrate the technical feasibility of operating a directly-fired HTAH (including both the heater matrix and valves), to continue obtaining information on life and corrosion resistance of HTAH materials, and to obtain design information for full-scale studies and future design work. The objectives of task 3 are to begin the identification of HTAH control requirements and control system needs, and to continue full-scale study efforts incorporating updated materials and design information in order to identify development needs for the HTAH development program. (WHK)

  2. Solar heating and hot water system for the central administrative office facility. Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    1978-11-01

    Progress on the solar heating and hot water system for the central administrative office facility of the Lincoln Housing Authority, Lincoln, NE is covered. An acceptance test plan is presented and the results of the test are tabulated. A complete blueprint of the system as built is provided. The monitoring system is drawn and settings and installation are described. An operation and maintenance manual discusses procedures for start up, shut down and seasonal changeover and include a valve list and pictures and specifications of components and materials used. Photographs of the final installation are included, and technical data and performance data are given. Finally, there is a brief description of system design and operation and a discussion of major maintenance problems encountered and their solutions. (LEW)

  3. Energy conservation in citrus processing. Technical progress report, October 1, 1979-March 31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-15

    The principal objective of the work is to identify an economically viable alternative to the existing method of meeting the energy requirements of citrus fruit processing that will substantially reduce the overall energy usage of citrus processing plants. The components which will make up the alternative systems include: evaporators, dryers, refrigeration units, heat pumps, heat engines, heat exchangers, thermal storage units, and ancillary components. These components will be used to form the five operational units of the citrus processing plant. These operational units are: evaporation, drying, refrigeration, pasteurizing and canning, and the plant electrical load that consists of operations such as conveying and juice extraction. The five operational units are then interrelated to varying degrees with respect to energy exchange to form different types of alternative systems. The approach, work plan, and progress of technical work are summarized. (MCW)

  4. Redwood Community Action Agency: Technical progress report, 3rd quarter, 1986

    Energy Technology Data Exchange (ETDEWEB)

    1986-01-01

    Since the second quarter, at which time venture feasibility activities were well underway by Redwood Community Action Agency (RCAA) to develop a shared-savings energy business plan, significant progress has been made. Nearly all consultant reports on the technical feasibility analysis have been completed, initial market research has begun and capitalization strategy has been investigated. Additionally, RCAA received an award of a substantial grant from the California Dept. of Economic Opportunity to develop a series of business ventures with a consortium of Northern California community providers. Fifteen thousand dollars of equity capital has been allocated for the energy-related business venture being investigated under this grant. If all plans go as anticipated, this money, combined with agency unrestricted funds, will provide the initial seed capital for the venture.

  5. Sonic enhanced ash agglomeration and sulfur capture. Technical progress report: January 1993--March 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-31

    This 15th Quarterly Technical Progress Report presents the results of work accomplished during the period January 4, 193 through March 28, 1993 under Contract No. DE-AC21-88MC26288 entitled {open_quotes}Sonic Enhanced Ash Agglomeration and Sulfur Capture.{close_quotes} The fundamental studies conducted by West Virginia University and Pennsylvania State University are provided in subsections of this report. Shakedown testing continued through this period resulting in a series of required modifications for the coal-feed system, coal injector, installation of a water-cooling jacket at the bottom of the agglomeration chamber, and finally, the installation of an additional flow sensor and rate meter. Coal-fired bimodal tests were initiated at the end of the period. The unit was run at 2 atm pressure for 3 hours with steady-state operation for 2 hours. Then, the pressure was increased to 3 atm with steady-state operation for 2 hours.

  6. Energy conservation in citrus processing. Technical progress report, October 1, 1979-March 31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-15

    The Sunkist Citrus Plant in Ontario, California, processes about 6 million pounds of citrus fruit per day to make products which include frozen concentrated juice; chilled, pasteurized, natural strength juice; molasses from peel; dried meal from peel; pectin; citrus oil; and bioflavonoids. The energy intensive operations at the plant include concentration, drying, and refrigeration. The objective of the two-year two-phase project is to identify an economically viable alternative to the existing method of meeting energy requirements. Progress on the technical work of Phase I is reported. The following are summarized: requirements (energy price projection, atmospheric emission requirements, citrus juice quality constraints, economic evaluations); characterization (basic citrus processing operations, energy consumption and fruit processed vs time, identification and measurement of energy uses, energy balance for a typical citrus juice evaporator); and thermodynamic analysis (heat pump model, thermal evaporator, and co-generation model).

  7. Spray forming -- Aluminum: Third annual report (Phase 2). Technical progress -- Summary

    Energy Technology Data Exchange (ETDEWEB)

    Kozarek, R.L.

    1998-04-20

    Commercial production of aluminum sheet and plate by spray atomization and deposition is a potentially attractive manufacturing alternative to conventional ingot metallurgy/hot-milling and to continuous casting processes because of reduced energy requirements and reduced cost. To realize the full potential of the technology, the Aluminum Company of America (Alcoa), under contract by the US Department of Energy, is investigating currently available state-of-the-art atomization devices to develop nozzle design concepts whose spray characteristics are tailored for continuous sheet production. This third technical progress report will summarize research and development work conducted during the period 1997 October through 1998 March. Included are the latest optimization work on the Alcoa III nozzle, results of spray forming runs with 6111 aluminum alloy and preliminary rolling trials of 6111 deposits.

  8. MHD Integrated Topping Cycle Project. Fourteenth quarterly technical progress report, November 1, 1990-- January 31, 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-02-01

    This fourteenth quarterly technical progress report of the MHD Integrated Topping Cycle Project presents the accomplishments during the period November 1, 1990 to January 31, 1991. Testing of the High Pressure Cooling Subsystem electrical isolator was completed. The PEEK material successfully passed the high temperature, high pressure duration tests (50 hours). The Combustion Subsystem drawings were CADAM released. The procurement process is in progress. An equipment specification and RFP were prepared for the new Low Pressure Cooling System (LPCS) and released for quotation. Work has been conducted on confirmation tests leading to final gas-side designs and studies to assist in channel fabrication.The final cathode gas-side design and the proposed gas-side designs of the anode and sidewall are presented. Anode confirmation tests and related analyses of anode wear mechanisms used in the selection of the proposed anode design are presented. Sidewall confirmation tests, which were used to select the proposed gas-side design, were conducted. The design for the full scale CDIF system was completed. A test program was initiated to investigate the practicality of using Avco current controls for current consolidation in the power takeoff (PTO) regions and to determine the cause of past current consolidation failures. Another important activity was the installation of 1A4-style coupons in the 1A1 channel. A description of the coupons and their location with 1A1 channel is presented herein.

  9. Use of fluidized bed combustion by-products for liners and alkali substitutes. Technical report, March 1--May 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Paul, B.C.; Esling, S. [Southern Illinois Univ., Carbondale, IL (United States); Pisani, F. [Illinois Abandoned Mined Lands reclamation Council (United States); Wells, T. [Archer-Daniels-Midland Co., Minneapolis, MN (United States)

    1995-12-31

    Fluidized Bed Combustion of coal eliminates most emissions of S and N oxides but produces sizable volumes of a solid residue that EPA may require to be placed in capped and lined landfills. Fluidized Bed Combustors are one of the most promising growth markets for Illinois coal and imposing cap and liner requirements may make the technology uneconomic. Fluidized Bed residues are cementlike and when mixed with soil, produce a material as impermeable as the clay liners used at landfills. This project will demonstrate that the residues can be mixed with soils by regular construction equipment and used in place of clays as liner material. The demonstration cap will cover an area of 7 acres and will prevent water infiltration into acid producing material. Baseline studies of Briar Creek indicate that the water is now highly degraded by acid drainage. Construction delays have enhanced the data collected on Briar Creek by allowing monitoring to continue through major seasonal changes without any effects attributable to the FBC ash. Materials needed to place the wells and lysimeters have been obtained. A contractor will build and deliver a mobile foam generator and spray to the field to demonstrate fugitive dust control from FBC fly ash (dust problem is one key barrier to more widespread use of FBC ash).

  10. Developing and upgrading of solar system thermal energy storage simulation models. Technical progress report, March 1, 1978-August 31, 1978

    Energy Technology Data Exchange (ETDEWEB)

    Kuhn, J K; von Fuchs, G F; Warren, A W; Zob, A P

    1979-07-01

    The objective of the program are: 1) collect, standardize, and link existing TES models from the literature and other STO contractors; 2) correlate TES models with available TES component test data; 3) develop streamlined versions of validated TES component models; and 4) provide DOE and industry with a competent solar TES simulation tool. Progress during the reporting period was concerned primarily with the first and second objectives. A rock bed model was evolved and analytical results were correlated with component test data, and water tank model development was continued in detail. Progress is detailed. (WHK)

  11. Final Technical Progress Report: Development of Low-Cost Suspension Heliostat; December 7, 2011 - December 6, 2012

    Energy Technology Data Exchange (ETDEWEB)

    Bender, W.

    2013-01-01

    Final technical progress report of SunShot Incubator Solaflect Energy. The project succeeded in demonstrating that the Solaflect Suspension Heliostat design is viable for large-scale CSP installations. Canting accuracy is acceptable and is continually improving as Solaflect improves its understanding of this design. Cost reduction initiatives were successful, and there are still many opportunities for further development and further cost reduction.

  12. Sulfur removal in advanced two stage pressurized fluidized bed combustion. Technical report, 1 March--31 May 1994

    Energy Technology Data Exchange (ETDEWEB)

    Abbasian, J.; Chowdiah, P.; Hill, A.H.; Rue, D.M. [Inst. of Gas Technology, Chicago, IL (United States)

    1994-09-01

    The objective of this study is to obtain data on the rates of reaction between hydrogen sulfide (H{sub 2}S) and uncalcined calcium-based sorbents under operating conditions relevant to first stage (carbonizer) of Advanced Two-Stage Pressurized Fluidized-Bed Combustors (PFBC). In these systems the CO{sub 2} partial pressure in the first stage generally exceeds the equilibrium value for calcium carbonate decomposition. Therefore, removal of sulfur compounds takes place through the reaction between H{sub 2}S and calcium carbonate. To achieve this objective, the rates of reaction between hydrogen sulfide and uncalcined calcium-based sorbents will be determined by conducting tests in pressurized thermogravimetric analyzer (TGA) and high-pressure/high-temperature fluidized-bed reactor (HPTR) units. The effects of sorbent type, sorbent particle size, reactor temperature and pressure, and CO{sub 2} and H{sub 2}S partial pressures on the sulfidation reaction rate will be determined. During this quarter a series of sulfidation tests were conducted in the high-pressure/high-temperature fluidized-bed reactor (HPTR) units. The effects of sorbent type, sorbent particle size, reactor temperature and pressure, and CO{sub 2} and H{sub 2}S partial pressures on the sulfidation reaction rate will be determined. During this quarter a series of sulfidation tests were conducted in the high-pressure high-temperature thermogravimetric analyzer (HPTGA unit) using limestone and dolomite. The results suggest that half-calcined dolomite is much more reactive than uncalcined limestone. Also, temperature in the range of 800 to 950 C did not significantly affect the sulfidation reaction rates for both limestone and dolomite.

  13. Chaotic behavior control in fluidized bed systems using artificial neural network. Quarterly progress report, April 1, 1996--June 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Bodruzzaman, M.; Essawy, M.A.

    1996-07-30

    We have developed techniques to control the chaotic behavior in the Fluidized Bed (FBC) Systems using Artificial Neural Networks (ANNs). For those techniques to cross from theory to implementation, the computer programs we are developing have to be interfaced with the outside world, as a necessary step towards the actual interface with an FBC system or its experimental mock up. For this reason we are working on a Data Acquisition Board setup that will enable communication between our programs and external systems. Communication is planned to be enabled in both ways to deliver feedback signals from a system to the control programs in one way, and the control signals from the control programs to the controlled system in the other way. On the other hand, since most of our programs are PC based, they have to follow the revolutionary progress in the PC technology. Our programs were developed in the DOS environment using an early version of Microsoft C compiler. For those programs to meet the current needs of most PC users, we are working on converting those programs to the Windows environment, using a very advanced and up to date C++ compiler. This compiler is known as the Microsoft Visual C++ Version 4.0. This compiler enables the implementation of very professional and sophisticated Windows 95, 32 bit applications. It also allows a simple utilization of the Object Oriented Programming (OOP) techniques, and lots of powerful graphical and communication tools known as the Microsoft Foundation Classes (MFC). This compiler also allows creating Dynamic Link Libraries (DLLS) that can be liked together or with other Windows programs. These two main aspects, the computer-system interface and the DOS-Windows migration will give our programs a leap frog towards their real implementation.

  14. Methyl chloride via oxyhydrochlorination of methane. Quarterly technical progress report No. 7, April--June 1993

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    The purpose of this contract is to develop a process for converting light alkane gases to methyl chloride via oxyhydrochlorination using highly selective, stable catalysts in fixed-bed reactors designed to remove the large amount of heat generated, so as to control the reaction temperature. Further, the objective is to obtain the engineering data base necessary for developing a commercially feasible process and to evaluate the economics of the process. Several key technology areas were evaluated this quarter. The catalyst definition effort focused on the determination of the role of the Li and La promoters that have been found to be useful in enhancing Cu based oxyhydrochlorination of methane catalysts. Initial experiments show that the La acts to provide a much more active catalyst than the Cu only case. The role of the Li is ambiguous at this point. The Li enhances the stability of the La promoted catalyst, but gives only marginal improvement by itself This work will be continued, with additional emphasis on the analysis of the catalysts to determine the structural role that the promoters may play. The separation unit operation definition made significant progress by demonstrating in a laboratory system that a process solvent may be used to remove the product CH{sub 3}Cl from the reactor effluent stream. To date the data has been qualitative, but clear. Work will continue to gather the information possible in the laboratory to help with PDU design. An extensive amount of testing was performed on the chosen process solvent, Multitherm. A comprehensive review of all the thermal testing and associated FTIR, UV/VIS, and physical property testing is included in this report. This work shows that Multitherm should give the desired stability and solubility that are necessary to make the separation unit operation successful.

  15. Sulfur removal in advanced two stage pressurized fluidized bed combustion. Technical report, December 1, 1994--February 28, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Abbasian, J.

    1996-03-01

    The objective of this study is to obtain data on the rates and the extent of sulfation reactions involving partially sulfided calcium-based sorbents, and oxygen as well as sulfur dioxide, at operating conditions closely simulating those prevailing in the second stage (combustor) of Advanced Two-Stage Pressurized Fluidized-Bed Combustors (PFBC). In these systems the CO{sub 2} partial pressure generally exceeds the equilibrium value for calcium carbonate decomposition. Therefore, calcium sulfate is produced through the reactions between SO{sub 2} and calcium carbonate as well as the reaction between calcium sulfide and oxygen. To achieve this objective, the rates of reaction involving SO{sub 2} and oxygen (gaseous reactant); and calcium sulfide and calcium carbonate (solid reactants), will be determined by conducting tests in a pressurized thermogravimetric analyzer (HPTGA) unit. The effects of sorbent type, sorbent particle size, reactor temperature and pressure; and O{sub 2} as well as SO{sub 2} partial pressures on the sulfation reactions rate will be determined. During this quarter, samples of the selected limestone and dolomite, sulfided in the fluidized-bed reactor during last quarter, were analyzed. The extent of sulfidation in these samples was in the range of 20 to 50%, which represent carbonizer discharge material at different operating conditions. The high pressure thermogravimetric analyzer (BPTGA) unit has been modified and a new pressure control system was installed to eliminate pressure fluctuation during the sulfation tests.

  16. Sulfur removal in advanced two-stage fluidized-bed combustion. [Quarterly] technical report, December 1, 1993--February 28, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Abbasian, J.; Hill, A.H.; Wangerow, J.R.; Rue, D.M. [Inst. of Gas Technology, Chicago, IL (United States)

    1994-06-01

    The objective of this study is to obtain data on the rates of reaction between, hydrogen sulfide (H{sub 2}S) and uncalcined calcium-based sorbents under operating conditions relevant to first stage (carbonizer) of Advanced Two-Stage Pressurized Fluidized-Bed Combustors (PFBC). In these systems the CO{sub 2} partial pressure in the first stage generally exceeds the equilibrium value for calcium carbonate decomposition. Therefore, removal of sulfur compounds takes place through the reaction between H{sub 2}S and calcium carbonate. To achieve this objective the rates of reaction between hydrogen sulfide and uncalcined calcium-based sorbents will be determined by conducting tests in pressurized thermogravimetric analyzer (TGA) and high-pressure/high-temperature fluidized-bed reactor (HPTR) units. The effects of sorbent type, sorbent particle size, reactor temperature and pressure, and CO{sub 2} and H{sub 2}S partial pressures on the sulfidation reaction rate will be determined. During this quarter, the high-pressure thermogravimetric analyzer (HPTGA) unit was installed and the shakedown process was completed. Several tests were conducted in the HPTGA unit to establish the operating procedure and the repeatability of the experimental results. Sulfidation by conducting the baseline sulfidation tests. The results are currently being analyzed.

  17. Sulfur removal in advanced two stage pressurized fluidized bed combustion. Technical report, September 1--November 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Abbasian, J.; Hill, A.; Wangerow, J.R. [Inst. of Gas Technology, Chicago, IL (United States)

    1994-12-31

    The objective of this study is to obtain data on the rates and the extent of sulfation reactions involving partially sulfided calcium-based sorbents, and oxygen as well as sulfur dioxide, at operating conditions closely simulating those prevailing in the second stage (combustor) of Advanced Two-Stage Pressurized Fluidized-Bed Combustors (PFBC). In these systems the CO{sub 2} partial pressure generally exceeds the equilibrium value for calcium carbonate decomposition. Therefore, calcium sulfate is produced through the reactions between SO{sub 2} and calcium carbonate as well as the reaction between calcium sulfide and oxygen. To achieve this objective, the rates of reaction involving SO{sub 2} and oxygen (gaseous reactant); and calcium sulfide and calcium carbonate (solid reactants), will be determined by conducting tests in a pressurized thermogravimetric analyzer (HPTGA) unit. The effects of sorbent type, sorbent particle size, reactor temperature and pressure; and O{sub 2} as well as SO{sub 2} partial pressures on the sulfation reactions rate will be determined. During this quarter, samples of the selected limestone and dolomite were sulfided in the fluidized-bed reactor. These tests were conducted in both calcining and non-calcining operating conditions to produce partially-sulfided sorbents containing calcium oxide and calcium carbonate, respectively. These samples which represent the carbonizer discharge material, will be used as the feed material in the sulfation tests to be conducted in the HPTGA unit during the next quarter.

  18. Technical Progress of Rubber Additives%橡胶助剂技术进展

    Institute of Scientific and Technical Information of China (English)

    齐琳; 梁诚

    2013-01-01

    In this review, the development and application of rubber additives are presented, including antioxidant 4030, antioxidant 4050, accelerator TBSI and TBZTD, anti-reversion agent Perkalink900, peptizer, homogenizing agent and resorcinol resin. The technical progress of production processes of several rubber additives is reviewed, for example, 4-aminodiphenylamine from nitrobenzene, antioxidant DTPD from mixed amine, and thiazole accelerators through clean process. The growth of China rubber additive industry relies strongly on continuous technological innovation.%介绍防老剂4030和4050等防护体系助剂,促进剂TBSI和TBZTD、抗硫化返原剂Perkalink900等硫化体系助剂,以及塑解剂、均匀剂、间苯二酚树脂等加工助剂的开发和应用。综述对氨基二苯胺硝基苯法工艺、混合胺合成防老剂DTPD工艺、噻唑类促进剂清洁工艺等进展。我国橡胶助剂工业应不断科技创新,才能够做大做强。

  19. MHD Integrated Topping Cycle Project. Sixteenth quarterly technical progress report, May 1991--July 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    The Magnetohydrodynamics (MHD) Integrated Topping Cycle (ITC) Project represents the culmination of the proof-of-concept (POC) development stage in the US Department of Energy (DOE) program to advance MHD technology to early commercial development stage utility power applications. The project is a joint effort, combining the skills of three topping cycle component developers: TRW, Avco/TDS, and Westinghouse. TRW, the prime contractor and system integrator, is responsible for the 50 thermal megawatt (50 MW{sub t}) slagging coal combustion subsystem. Avco/TDS is responsible for the MHD channel subsystem (nozzle, channel, diffuser, and power conditioning circuits), and Westinghouse is responsible for the current consolidation subsystem. The ITC Project will advance the state-of-the-art in MHD power systems with the design, construction, and integrated testing of 50 MW{sub t} power train components which are prototypical of the equipment that will be used in an early commercial scale MHD utility retrofit. Long duration testing of the integrated power train at the Component Development and Integration Facility (CDIF) in Butte, Montana will be performed, so that by the early 1990`s, an engineering data base on the reliability, availability, maintainability and performance of the system will be available to allow scaleup of the prototypical designs to the next development level. This Sixteenth Quarterly Technical Progress Report covers the period May 1, 1991 to July 31, 1991.

  20. MHD air heater development technology. Technical progress report, April 1, 1980-June 30, 1980

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-07-01

    Technology development for the directly-fired high temperature air heater (HTAH) for MHD power plants is described. Work is being done under three tasks as described in the following. (1) materials selection, evaluation, and development: The objective of this task is to continue development of ceramic materials technology for the directly-fired HTAH. The scope of the work will include compilation of materials data, materials selection for testing and design studies, materials property determination, liaison with refractory manufacturers and other organizations to encourage development of materials and fabrication technology, establishment of preliminary HTAH material specifications, analyses of test materials, and development of criteria for thermal stress limits for crack-tolerant refractory materials. (2) operability, performance, and materials testing: The objectives of this task are to demonstrate the technical feasibility of operating a directly-fired HTAH (including both the heater matrix and valves), to continue obtaining information on life and corrosion resistance of HTAH materials, and to obtain design information for full-scale studies and future design work. (3) full-scale design concepts: The objectives of this task are to begin the identification of HTAH control requirements and control system needs, and to continue full-scale study efforts incorporating updated materials and design information in order to identify development needs for the HTAH development program. Progress is described. (WHK)

  1. PFBC HGCU Test Facility. Technical progress report No. 24, Third quarter, CY 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-01

    This is the twenty-fourth and final Technical Progress Report submitted to the Department of Energy (DOE) in connection with the cooperative agreement between the DOE and Ohio Power Company for the Tidd PFBC Hot Gas Clean Up Test Facility. This report covers the work completed during the Third Quarter of CY 1995. All activity this quarter was directed toward the completion of the program final report. A draft copy of the final report was forwarded to DOE during this quarter, and DOE submitted their comments on the report to AEPSC. DOE requested that Westinghouse write an appendix to the report covering the performance of the fail-safe regenerator devices during Tad operation, and Westinghouse subsequently prepared the appendix. Additional DOE comments were incorporated into the report, and it will be issued in camera-ready form by the end of October, 1995, which is the program end date. Appendix 1 presents the results of filter candle posttest examination by Westinghouse performed on selected filter candles following final shutdown of the system.

  2. Coal liquefaction process streams characterization and evaluation. Quarterly technical progress report, April 1--June 30, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Brandes, S.D.; Lancet, M.S.; Robbins, G.A.; Winschel, R.A.; Burke, F.P.

    1992-11-01

    This is the eleventh Quarterly Technical Progress Report under DOE Contract DE-AC22-89PC89883. Major topics reported are: (1) The results of a study designed to determine the effects of the conditions employed at the Wilsonville slurry preheater vessel on coal conversion is described. (2) Stable carbon isotope ratios were determined and used to source the carbon of three product samples from Period 49 of UOP bench-scale coprocessing Run 37. The results from this coprocessing run agree with the general trends observed in other coprocessing runs that we have studied. (3) Microautoclave tests and chemical analyses were performed to ``calibrate`` the reactivity of the standard coal used for determining donor solvent quality of process oils in this contract. (4) Several aspects of Wilsonville Close-Coupled Integrated Two-Stage Liquefaction (CC-ITSL) resid conversion kinetics were investigated; results are presented. Error limits associated with calculations of deactivation rate constants previously reported for Runs 258 and 261 are revised and discussed. A new procedure is described that relates the conversions of 850{degrees}F{sup +} , 1050{degrees}F{sup +}, and 850 {times} 1050{degrees}F material. Resid conversions and kinetic constants previously reported for Run 260 were incorrect; corrected data and discussion are found in Appendix I of this report.

  3. Jointly sponsored research program quarterly technical progress report, January--March 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-01

    Progress reports are presented for the following tasks: Development and demonstration of a practical electric downhole steam generator for thermal recovery of heavy oil and tar; wetting behavior of selected crude oil/brine/rock systems; coal gasification, power generation, and product market study; impact of leachate from clean coal technology waste on the stability of clay liners; investigation of coprocessing of heavy oil, automobile shredder residue, and coal; injection into coal seams for simultaneous CO{sub 2} mitigation and enhanced recovery of coalbed methane; optimization of carbonizer operations in the FMC coke process; chemical sensor and field screening technology development; demonstration of the Koppelman ``Series C`` Power River Basin coal as feed; remote chemical sensor development; market assessment and technical feasibility study of PFBC ash use; solid-state NMR analysis and interpretation of naturally and artificially matured kerogens; Crow{trademark} field demonstration with Bell Lumber and Pole; ``B`` series pilot plant tests; and in-situ treatment of manufactured gas plant contaminated soils demonstration program.

  4. Critical contributions in MHD power generation. Quarterly technical progress report, December 1, 1977-February 28, 1978

    Energy Technology Data Exchange (ETDEWEB)

    Louis, J.F.

    1978-03-01

    Research and development in open-cycle coal-fired MHD power generation is described. The scope and objectives of the MIT program are: (1) establish chemical, thermal, and electrical data to guide materials selection, develop improved detail designs, and support performance analyses of MHD electrode modules and insulator materials; (2) parametrically investigate selected electrode properties of critical design importance in chemical, thermal, and electrical environments simulating a coal-fired MHD generator; (3) develop combustion data pertinent to the design of MHD combustors; (4) establish techniques for the analysis and understanding of critical MHD phenomena which have an important bearing on MHD generator performance; such phenomena include inter-electrode breakdown, time-dependent behavior, effective plasma properties and plasma inhomogeneities; (5) establish the operating characteristics of an MHD disk generator; (6) continue work on computer techniques for modeling and for design and cost analysis of MHD components and the overall system; (7) integrate the engineering data and design criteria, as applicable, which are developed in the listed tasks into a model of the MHD channel; (8) participate in the US/USSR Cooperative Program in MHD Power Generation; and (9) participate in technical support of the DOE MHD Project Office. Progress in each of these areas is reported. (WHK)

  5. Critical contributions in MHD power generation. Quarterly technical progress report, September 1--November 30, 1977

    Energy Technology Data Exchange (ETDEWEB)

    Louis, J.F.

    1977-12-01

    Research and development in open-cycle coal-fired MHD power generation at Massachusetts Institute of Technology (MIT) is summarized. Progress is reported on the following tasks: (1) Establish chemical, thermal, and electrical data to guide materials selection, develop improved detail designs, and support performance analyses of MHD electrode modules and insulator materials; (2) parametrically investigate selected electrode properties of critical design importance in chemical, thermal, and electrical environments simulating a coal-fired MHD generator; (3) develop combustion data pertinent to the design of MHD combustors; this work is intended to determine the combustion characteristics of selected coal feedstock in terms of devolatilization kinetics, char characteristics, and combustion gas chemistry; (4) establish techniques for the analysis and understanding of critical MHD phenomena which have an important bearing on MHD generator performance; such phenomena include inter-electrode breakdown, time-dependent behavior, effective plasma properties and plasma inhomogeneities; (5) establish the operating characteristics of an MHD disk generator; (6) continue work on computer techniques for modeling and for design and cost analysis of MHD components and the overall system; (7) integrate the engineering data and design criteria, as applicable, which are developed in the above-listed tasks into a model of the MHD channel; (8) participate in technical support of the DOE MHD Project Office.

  6. Technical Progress of Domestic Iron & Steel Industry and Its Influence on the Development of Refractories

    Institute of Scientific and Technical Information of China (English)

    XINGShouwei; LIUJiehua

    2001-01-01

    The quick increase of domestic iron and steel output,the great improvement of steel quality and variety,the improtation of advanced equipment and the diminution and elimination of some backward technology and facilities have brought about great influence on the development of refracetories.In order to meet the technical progress of iron and steel industry,domestic refractories industry has,in the last industry,domestic refractories industry has,in the last decades ,concentrated its efforts on the development and production of new Sialon bonded SiC bricks and micropore carbon blocks for giant blast furnaces;new refractories for coke oven and non-coke iron making furnaces;MgO-C bricks for converters and electric conductive refractories for UHP EAF;refractories for slag splashing technology;and the highy technology-intensive refractories for continuous casting facilities.The paper reviews the great change occurred in the industries of iron-and steel-making and refratories during the last decaldes.

  7. Coal liquefaction process streams characterization and evaluation. Quarterly technical progress report, January 1--March 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Robbins, G.A.; Brandes, S.D.; Winschel, R.A.; Burke, F.P.

    1992-08-01

    This is the tenth Quarterly Technical Progress Report under DOE Contract DE-AC22-89PC89883. Process oils from Wilsonville Run 262 were analyzed to provide information on process performance. Run 262 was operated from July 10 through September 30, 1991, in the thermal/catalytic Close-Coupled Integrated Two-Stage Liquefaction (CC-ITSL) configuration with ash recycle. The feed coal was Black Thunder Mine subbituminous coal. The high/low temperature sequence was used. Each reactor was operated at 50% of the available reactor volume. The interstage separator was in use throughout the run. The second-stage reactor was charged with aged Criterion 324 catalyst (Ni/Mo on 1/16 inch alumina extrudate support). Slurry catalysts and sulfiding agent were fed to the first-stage reactor. Molyvan L is an organometallic compound which contains 8.1% Mo, and is commercially available as an oil-soluble lubricant additive. It was used in Run 262 as a dispersed hydrogenation catalyst precursor, primarily to alleviate deposition problems which plagued past runs with Black Thunder coal. One test was made with little supported catalyst in the second stage. The role of phenolic groups in donor solvent properties was examined. In this study, four samples from direct liquefaction process oils were subjected to O-methylation of the phenolic groups, followed by chemical analysis and solvent quality testing.

  8. MHD Integrated Topping Cycle Project. Sixteenth quarterly technical progress report, May 1991--July 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    The Magnetohydrodynamics (MHD) Integrated Topping Cycle (ITC) Project represents the culmination of the proof-of-concept (POC) development stage in the US Department of Energy (DOE) program to advance MHD technology to early commercial development stage utility power applications. The project is a joint effort, combining the skills of three topping cycle component developers: TRW, Avco/TDS, and Westinghouse. TRW, the prime contractor and system integrator, is responsible for the 50 thermal megawatt (50 MW{sub t}) slagging coal combustion subsystem. Avco/TDS is responsible for the MHD channel subsystem (nozzle, channel, diffuser, and power conditioning circuits), and Westinghouse is responsible for the current consolidation subsystem. The ITC Project will advance the state-of-the-art in MHD power systems with the design, construction, and integrated testing of 50 MW{sub t} power train components which are prototypical of the equipment that will be used in an early commercial scale MHD utility retrofit. Long duration testing of the integrated power train at the Component Development and Integration Facility (CDIF) in Butte, Montana will be performed, so that by the early 1990`s, an engineering data base on the reliability, availability, maintainability and performance of the system will be available to allow scaleup of the prototypical designs to the next development level. This Sixteenth Quarterly Technical Progress Report covers the period May 1, 1991 to July 31, 1991.

  9. PFBC HGCU test facility technical progress report. First Quarter, CY 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-01

    This is the eighteenth Technical Progress Report submitted in connection with the cooperative agreement between the DOE and Ohio Power Company for the Tidd PFBC Hot Gas Clean Up Test Facility. During this quarter, the Tidd Hot Gas Clean Up System operated for 835 hours during six separate test runs. The system was starting into a seventh run at the end of the quarter. Highlights of this period are summarized below: the longest run during the quarter was approximately 333 hours; filter pressure drop was stable during all test runs this quarter using spoiling air to the primary cyclone upstream of the Advanced Particle Filter (APF); the tempering air system was commissioned this quarter which enabled the unit to operate at full load conditions while limiting the gas temperature in the APF to 1,400 F; during a portion of the one run, the tempering air was removed and the filter operated without problems up to 1,450 F; ash sampling was performed by Battelle personnel upstream and downstream of the APF and ash loading and particle size distribution data were obtained, a summary report is included; a hot area on the APF head was successfully repaired in service; a hot spot on the top of an expansion joint was successfully repaired by drilling holes from the inside of the pipe and pumping in refractory insulation; a corrosion inspection program for the HGCU system was issued giving recommendations for points to inspect; filter internal inspections following test runs 13 and 17 revealed a light coating (up to 1/4 inch thick) of residual ash on the candles and some ash bridging between the dust sheds and inner rows of candles. Data from these inspections are included with this report.

  10. Instrumentation of dynamic gas pulse loading system. Technical progress report, first quarter 1992

    Energy Technology Data Exchange (ETDEWEB)

    Mohaupt, H.

    1992-04-14

    The overall goal of this work is to further develop and field test a system of stimulating oil and gas wells, which increases the effective radius of the well bore so that more oil can flow into it, by recording pressure during the gas generation phase in real time so that fractures can be induced more predictably in the producing formation. Task 1: Complete the laboratory studies currently underway with the prototype model of the instrumentation currently being studied. Task 2: Perform field tests of the model in the Taft/Bakersfield area, utilizing operations closest to the engineers working on the project, and optimize the unit for various conditions encountered there. Task 3: Perform field test of the model in DGPL jobs which are scheduled in the mid-continent area, and optimize the unit for downhole conditions encountered there. Task 4: Analyze and summarize the results achieved during the complete test series, documenting the steps for usage of downhole instrumentation in the field, and compile data specifying use of the technology by others. Task 5: Prepare final report for DOE, and include also a report on the field tests completed. Describe and estimate the probability of the technology being commercialized and in what time span. The project has made substantial technical progress, though we are running about a month behind schedule. Expenditures are in line with the schedule. Increased widespread interest in the use of DGPL stimulation has kept us very busy. The computer modeling and test instrumentation developed under this program is already being applied to commercial operations.

  11. Critical contributions in MHD power generation. Quarterly technical progress report, December 1, 1976--February 28, 1977

    Energy Technology Data Exchange (ETDEWEB)

    Louis, J.F.

    1977-08-01

    Research progress in open-cycle coal-fired MHD power generation at Massachusetts Institute of Technology (MIT) is reported. The scope and objectives of the MIT program are to: (1) Establish chemical, thermal, and electrical data to guide materials selection, develop improved detail designs, and support performance analyses of MHD electrode modules and insulator materials; (2) establish basic mechanical properties to guide detail design and fabrication of high field strength superconducting magnets for MHD applications; (3) parametrically investigate selected electrode properties of critical design importance in chemical, thermal, and electrical environments simulating a coal-fired MHD generator; (4) develop combustion data pertinent to the design of MHD combustors; (5) establish techniques for the analysis and understanding of critical MHD phenomena which have an important bearing on MHD generator performance; such phenomena include inter-electrode breakdown, time-dependent behavior, effective plasma properties and plasma inhomogeneities; (6) establish the operating characteristics of an MHD disk generator; (7) continue work on computer techniques for modeling and for design and cost analysis of MHD components and the overall system; (8) integrate the engineering data and design criteria, as applicable, which are developed in the above-listed tasks into a model of the MHD channel; (9) Participate in technical support of the ERDA MHD Project Office; (10) participate in the US/USSR Cooperative Program in MHD Power Generation. (11) During the summer of 1976, a short-term task in U-25 electrode screening was temporarily added to the scope of the contract. This effort involved screening tests, in the MIT MHD simulation facility of electrode modules and configurations intended for tests in the Soviet U-25 generator.

  12. Technical Note: A numerical test-bed for detailed ice nucleation studies in the AIDA cloud simulation chamber

    Directory of Open Access Journals (Sweden)

    R. J. Cotton

    2007-01-01

    Full Text Available The AIDA (Aerosol Interactions and Dynamics in the Atmosphere aerosol and cloud chamber of Forschungszentrum Karlsruhe can be used to test the ice forming ability of aerosols. The AIDA chamber is extensively instrumented including pressure, temperature and humidity sensors, and optical particle counters. Expansion cooling using mechanical pumps leads to ice supersaturation conditions and possible ice formation. In order to describe the evolving chamber conditions during an expansion, a parcel model was modified to account for diabatic heat and moisture interactions with the chamber walls. Model results are shown for a series of expansions where the initial chamber temperature ranged from −20°C to −60°C and which used desert dust as ice forming nuclei. During each expansion, the initial formation of ice particles was clearly observed. For the colder expansions there were two clear ice nucleation episodes. In order to test the ability of the model to represent the changing chamber conditions and to give confidence in the observations of chamber temperature and humidity, and ice particle concentration and mean size, ice particles were simply added as a function of time so as to reproduce the observations of ice crystal concentration. The time interval and chamber conditions over which ice nucleation occurs is therefore accurately known, and enables the model to be used as a test bed for different representations of ice formation.

  13. Sulfur removal in advanced two stage pressurized fluidized bed combustion. Technical report, March 1--May 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Abbasian, J.

    1995-12-31

    The objective of this study is to obtain data on the rates and the extent of sulfation reactions involving partially sulfided calcium-based sorbents, and oxygen as well as sulfur dioxide, at operating conditions closely simulating those prevailing in the second stage (combustor) of Advanced Two-Stage Pressurized Fluidized-Bed Combustors. In these systems the CO{sub 2} partial pressure generally exceeds the equilibrium value for calcium carbonate decomposition. Therefore, calcium sulfate is produced through the reactions between SO{sub 2} and calcium carbonate as well as the reaction between calcium sulfide and oxygen. To achieve this objective, the rates of reaction involving SO{sub 2} and oxygen, calcium sulfide and calcium carbonate will be determined by conducting tests in a pressurized thermogravimetric analyzer unit. The sulfate tests conducted during this quarter, focused on the determination of the rate of sulfation reaction involving partially sulfided half-calcined dolomite and oxygen. The test parameters included CO{sub 2} and O{sub 2} concentrations, reaction temperature and pressure, as well as the sorbent particle size. The results obtained during this quarter suggest that the rate of sulfation reaction involving partially sulfided half-calcined dolomite and oxygen is very fast at temperatures above 850 C which rapidly increases with increasing temperature, achieving more than 85% conversion in less than a few minutes. The reaction appears to continue to completion, however, above 85% conversion, the rate of reaction appears to be low, requiring long residence time to reach complete conversion.

  14. Savannah River Plant, Works Technical Department monthly progress report for March 1956

    Energy Technology Data Exchange (ETDEWEB)

    None

    1956-04-18

    This document details activities of the Works Technical Department during the month of March 1956. It covers reactor technology, separations technology, engineering assistance and heavy water technology.

  15. Hydrogen production by supercritical water gasification of biomass. Phase 1 -- Technical and business feasibility study, technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    The nine-month Phase 1 feasibility study was directed toward the application of supercritical water gasification (SCWG) for the economical production and end use of hydrogen from renewable energy sources such as sewage sludge, pulp waste, agricultural wastes, and ultimately the combustible portion of municipal solid waste. Unique in comparison to other gasifier systems, the properties of supercritical water (SCW) are ideal for processing biowastes with high moisture content or contain toxic or hazardous contaminants. During Phase I, an end-to-end SCWG system was evaluated. A range of process options was initially considered for each of the key subsystems. This was followed by tests of sewage sludge feed preparation, pumping and gasification in the SCW pilot plant facility. Based on the initial process review and successful pilot-scale testing, engineering evaluations were performed that defined a baseline system for the production, storage and end use of hydrogen. The results compare favorably with alternative biomass gasifiers currently being developed. The results were then discussed with regional wastewater treatment facility operators to gain their perspective on the proposed commercial SCWG systems and to help define the potential market. Finally, the technical and business plans were developed based on perceived market needs and the projected capital and operating costs of SCWG units. The result is a three-year plan for further development, culminating in a follow-on demonstration test of a 5 MT/day system at a local wastewater treatment plant.

  16. Hydrogen production by supercritical water gasification of biomass. Phase 1 -- Technical and business feasibility study, technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    The nine-month Phase 1 feasibility study was directed toward the application of supercritical water gasification (SCWG) for the economical production and end use of hydrogen from renewable energy sources such as sewage sludge, pulp waste, agricultural wastes, and ultimately the combustible portion of municipal solid waste. Unique in comparison to other gasifier systems, the properties of supercritical water (SCW) are ideal for processing biowastes with high moisture content or contain toxic or hazardous contaminants. During Phase I, an end-to-end SCWG system was evaluated. A range of process options was initially considered for each of the key subsystems. This was followed by tests of sewage sludge feed preparation, pumping and gasification in the SCW pilot plant facility. Based on the initial process review and successful pilot-scale testing, engineering evaluations were performed that defined a baseline system for the production, storage and end use of hydrogen. The results compare favorably with alternative biomass gasifiers currently being developed. The results were then discussed with regional wastewater treatment facility operators to gain their perspective on the proposed commercial SCWG systems and to help define the potential market. Finally, the technical and business plans were developed based on perceived market needs and the projected capital and operating costs of SCWG units. The result is a three-year plan for further development, culminating in a follow-on demonstration test of a 5 MT/day system at a local wastewater treatment plant.

  17. Learning Progressions: Tools for Assessment and Instruction for All Learners. Technical Report #1307

    Science.gov (United States)

    Sáez, Leilani; Lai, Cheng-Fei; Tindal, Gerald

    2013-01-01

    Conceptually, learning progressions hold promise for improving assessment and instruction by precisely outlining what students know and don't know at particular stages of knowledge and skill development. Based upon a synthesis of the literature, a rationale for the use of learning progressions maps to clarify how learning progresses in…

  18. Savannah River Ecology Laboratory, Annual Technical Progress Report of Ecological Research, June 30, 2002

    Energy Technology Data Exchange (ETDEWEB)

    Paul M. Bertsch, (Director)

    2002-06-30

    The Savannah River Ecology Laboratory (SREL) is a research unit of The University of Georgia (UGA) and has been conducting ecological research on the Savannah River Site (SRS) near Aiken, South Carolina for 50 years. The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts fundamental and applied ecological research, as well as education and outreach programs, under a Cooperative Agreement with the U.S. Department of Energy (DOE). The Laboratory's research mission during the 2002 fiscal year was fulfilled with the publication of 76 journal articles and book chapters by faculty, technical staff, students, and visiting scientists. An additional 50 journal articles have been submitted or are in press. Other noteworthy events took place as faculty members, staff, and graduate students received awards. These are described in the section titled Special Accomplishments of Faculty, Staff, Students, and Administration on page 51. Notable scientific accomplishments include work conducted on contaminant transport, stable isotopes, sandhills ecology, and phytoremediation: (1) A collaborative study between Dr. Tom Hinton at SREL and scientists at SRTC demonstrated the feasibility of using illite clay to sequester 137Cs in sediments along the P and R reactor cooling canal system, where approximately 3,000 acres of land are contaminated. Overall, the study showed significant decreases in cesium concentrations and bioavailability following the addition of illite with no sign of harm to the ecosystem. While the cesium remains sequestered from the biosphere, its radioactivity decays and the process progresses from contaminant immobilization to remediation. (2) SREL's stable isotope laboratory is now fully functional. Stable isotope distributions in nature can provide important insights into many historical and current environmental processes. Dr. Christopher Romanek is leading SREL's research

  19. Proceedings of the technical review on advances in geothermal reservoir technology---Research in progress

    Energy Technology Data Exchange (ETDEWEB)

    Lippmann, M.J. (ed.)

    1988-09-01

    This proceedings contains 20 technical papers and abstracts describing most of the research activities funded by the Department of Energy (DOE's) Geothermal Reservoir Technology Program, which is under the management of Marshall Reed. The meeting was organized in response to several requests made by geothermal industry representatives who wanted to learn more about technical details of the projects supported by the DOE program. Also, this gives them an opportunity to personally discuss research topics with colleagues in the national laboratories and universities.

  20. NRL Technical Year End Progress Report for MCSC PM-ICE FY11 SOW Tasks 1 and 2 - Hearing Loss

    Science.gov (United States)

    2012-05-18

    2 — Hearing Loss Research May 18, 2012 Approved for public release; distribution is unlimited. Peter C. HerdiC James W. mCmaHon daniel l. amon...Technical Year End Progress Report for MCSC PM-ICE FY11 SOW Tasks 1 and 2 — Hearing Loss Research Peter C. Herdic, James W. McMahon, Daniel L. Amon...deemed relevant to the warfighter. 18-05-2012 Memorandum Report Hearing loss Human ear Small weapons fire Shooter’s notch Program Manager, Infantry Combat

  1. Novel bimetallic dispersed catalysts for temperature-programmed coal liquefaction. Technical progress report, July--September 1996

    Energy Technology Data Exchange (ETDEWEB)

    Yoneyama, Yoshiharu; Wei, B.; Reddy, K.M.; Song, C.; Schobert, H.H.

    1997-01-01

    This quarterly report describes recent work on two related subjects: (1) effect of dispersed molybdenum catalyst precursor and the influence of water addition on C-O bond cleavage, aromatic hydrogenation and hydrodeoxygenation under coal liquefaction conditions, and (2) the effect of dispersed molybdenum catalyst precursor on the molecular weight reduction and desulfurization of petroleum resids related to coal/petroleum resids coprocessing. Technical progress on the C-O bond cleavage of 2,2{prime}-dinaphthyl ether and high temperature simulated distillation GC and HDS study on catalytic upgrading of atmospheric and vacuum resids.

  2. THE OPTIMAL ALLOCATION ABOUT CAPITAL AND LABOR IN THE ECONOMIC GROWTH WITH AN ENDOGENOUS TECHNICAL PROGRESS MODEL

    Institute of Scientific and Technical Information of China (English)

    刘金山; 李楚霖; 胡适耕

    2002-01-01

    In this paper, the balanced economic growth path was considered in a new growth model with endogenous technical progress. It is not only obtained the optimal allocation about capital and labor between a goods-producing sector and a R&D Sector,but also the optimal value of saving rates. By discussing the effect of parameters, it are also got the following results: When the rate of time preference (discount factor) rising, the fractions of Capital and labor in the goods-producing sector will increase , the fractions in R&D sector and the saving rates will decrease; When the population grows rapidly, the result will be contrary.

  3. Analysis of Sustainable Materials Used in Ecovillages:Review of Progress in BedZED and Masdar City

    Institute of Scientific and Technical Information of China (English)

    ZHU Dan; Michael Kung; Bill Whiteford; Alex Boswell-Ebersole

    2012-01-01

    This paper explores reclaimed and recycled material used in ecovillages.The models discussed in this paper include BedZED in the United Kingdom and Masdar City in the Middle East.These two communities contain features characterized by the sustainable principles of the ecovillage concept by using nontraditional building materials.The creations of more ecovillages,along with the growth of current ecovillages,play an important role in positively solvening environmental and social problems.The sustainable materials used in the ecovillages also act as a model for communities wishing to implement sustainable development.

  4. Index to Nuclear Safety: a technical progress review by chrology, permuted title, and author, Volume 11(1) through Volume 20(6)

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, W B; Passiakos, M

    1980-06-01

    This index to Nuclear Safety, a bimonthly technical progress review, covers articles published in Nuclear Safety, Volume II, No. 1 (January-February 1970), through Volume 20, No. 6 (November-December 1979). It is divided into three sections: a chronological list of articles (including abstracts) followed by a permuted-title (KWIC) index and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center (NSIC), covers all safety aspects of nuclear power reactors and associated facilities. Over 600 technical articles published in Nuclear Safety in the last ten years are listed in this index.

  5. Bed Bugs

    Science.gov (United States)

    Prevent, identify, and treat bed bug infestations using EPA’s step-by-step guides, based on IPM principles. Find pesticides approved for bed bug control, check out the information clearinghouse, and dispel bed bug myths.

  6. Technical progress report for the quarter 1 October-31 December 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    This report describes the technical accomplishments on the commercial nuclear waste management programs and on the geologic disposal of nuclear wastes. The program is organized into eight tasks: systems, waste package, site, repository, regulatory and institutional, test facilities and excavations, land acquisition, and program management. (DLC)

  7. Developing Technical Writing Skills in the Physical Chemistry Laboratory: A Progressive Approach Employing Peer Review

    Science.gov (United States)

    Gragson, Derek E.; Hagen, John P.

    2010-01-01

    Writing formal "journal-style" lab reports is often one of the requirements chemistry and biochemistry students encounter in the physical chemistry laboratory. Helping students improve their technical writing skills is the primary reason this type of writing is a requirement in the physical chemistry laboratory. Developing these skills is an…

  8. Atmospheric Effects of Nuclear Energy Centers (AENEC) Program. Annual technical progress report, July 1975--September 1976

    Energy Technology Data Exchange (ETDEWEB)

    Patrinos, A. A.; Hoffman, H. W. [comps.

    1977-04-01

    The Technical Memorandum contains information of a preliminary nature from the six participants of the Program describing their activities and presenting the results obtained during the reporting period. The birth of the Program, its definition and evolution are described, and a complete breakdown of responsibilities and tasks assigned to the six AENEC participants is presented.

  9. Developing Technical Writing Skills in the Physical Chemistry Laboratory: A Progressive Approach Employing Peer Review

    Science.gov (United States)

    Gragson, Derek E.; Hagen, John P.

    2010-01-01

    Writing formal "journal-style" lab reports is often one of the requirements chemistry and biochemistry students encounter in the physical chemistry laboratory. Helping students improve their technical writing skills is the primary reason this type of writing is a requirement in the physical chemistry laboratory. Developing these skills is an…

  10. Low-rank coal research under the UND/DOE cooperative agreement. Quarterly technical progress report, April 1983-June 1983

    Energy Technology Data Exchange (ETDEWEB)

    Wiltsee, Jr., G. A.

    1983-01-01

    Progress reports are presented for the following tasks: (1) gasification wastewater treatment and reuse; (2) fine coal cleaning; (3) coal-water slurry preparation; (4) low-rank coal liquefaction; (5) combined flue gas cleanup/simultaneous SO/sub x/-NO/sub x/ control; (6) particulate control and hydrocarbons and trace element emissions from low-rank coals; (7) waste characterization; (8) combustion research and ash fowling; (9) fluidized-bed combustion of low-rank coals; (10) ash and slag characterization; (11) organic structure of coal; (12) distribution of inorganics in low-rank coals; (13) physical properties and moisture of low-rank coals; (14) supercritical solvent extraction; and (15) pyrolysis and devolatilization.

  11. Space Power MHD (magnetohydrodynamic) System: Third quarterly technical progress report, 1 November 1987-31 January 1988

    Energy Technology Data Exchange (ETDEWEB)

    1988-03-15

    This progress report of the Space Power MHD System project presents the accomplishments during 1 November 1987 through 31 January 1988. The scope of work covered encompasses the definition of an MHD power system conceptual design and development plan (Task 1). Progress included the following: Subcontracts were issued to the MIT Plasma Fusion Center and the Westinghouse R and D Center. The performance of the 100 MW 500 sec. power system was optimized and the design concept finalized, including mass and energy balances. Mass and cost estimates were prepared. A design review was held at DOE/PETC. This also included the review of the technical issues definition and of the R and D Plan. Following the review, a final iteration on the conceptual design was initiated. Formulation of the R and D Plan was continued. Preparation of the Task 1 R and D Report was initiated. 12 figs.

  12. Measurements of scattering processes in negative ion - atom collisions. Technical progress report - year 1, April 1, 1995--March 31, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Kvale, T.J.

    1995-12-01

    This Technical Progress Report describes the progress made on the research objectives during the past twelve months. The objective of this research project is to provide absolute cross section measurements of various scattering processes which occur in negative ion collisions with atomic (specifically, noble gas and atomic hydrogen) targets at intermediate energies. These processes include: elastic scattering, single- and double-electron detachment, and target-inelastic processes of excitation and ionization. Total cross sections for single- and double-electron detachment were recently published in Physical Review A from this research project. The researchers were successful this past year in acquiring the first cross section measurements of target excitation for H{sup -} impact on helium target atoms.

  13. Technical and economical optimization of wood gasification in a circulating fluidized bed. Final report; Technische und wirtschaftliche Optimierung der Vergasung von Holz in der zirkulierenden Wirbelschicht. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Ising, M.; Unger, C.; Heunemann, F.; Dinkelbach, L.

    2002-12-01

    The project's objective was the optimization of a novel process for high efficient combined heat and power production from solid biomass. The processed air blown wood gasification in a pilot scale circulating fluidized bed was added by a catalytic tar reformer which would yield a tar-free gas quality suitable for IC-engine operation. Major efforts were taken for technical improvement of the tar reformer, especially concerning temperature control and cleaning devices which is important for keeping constantly a high activity. Pure natural timber did not yield chemical deactivation at the catalyst whereas the gasification of waste wood yielded decreasing activity which could be partly reversed by special measures taken. Further optimization of the process considered a better automation and improvement of the engine's flue gas emissions. Also a detailed economic consideration and evaluation of the entire process has been carried out. As a result the novel process should have economic advantages compared with conventional technology. (orig.) [German] Gegenstand des Vorhabens war die Weiterentwicklung eines Verfahrens zur effizienteren Strom- und Waermegewinnung aus festen Biobrennstoffen. Durch luftgeblasene Vergasung von Holz im Pilotmassstab in einer zirkulierenden Wirbelschicht und anschliessender katalytischer Teerspaltung konnte ein niederkalorisches Brenngas erzeugt werden, welches zum Betrieb eines Motoren-Blockheizkraftwerks geeignet war. Im Rahmen der Verfahrensoptimierung wurde der katalytische Teer-Reformer, insbesondere in Bezug auf Temperaturfuehrung und die zum Aktivitaetserhalt wichtige Abreinigungsvorrichtung, verbessert. Bei der Vergasung von Naturholz wurde keine chemische Desaktivierung festgestellt. Beim Altholzeinsatz wurde ein ueberwiegend reversibler Aktivitaetsverlust verzeichnet und begruendet. Geeignete Gegenmassnahmen wurden untersucht und beschrieben. Weitere Optimierungen betrafen die Anlagensteuerungstechnik im Hinblick auf die

  14. University of Florida, University research program in robotics. Annual technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Crane, C.D. III; Tulenko, J.S.

    1994-05-01

    Progress is reported in the areas of environmental hardening, database, world modeling, vision, man-machine interface, advanced liquid metal reactor inspection robot, and articulated transporter/manipulator system (ATMS) development.

  15. Information and Communications Technical Support Services to the Office of Environment, Safety, and Health. Progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-01

    Progress is reported on the following tasks: development of safety publications, conference support, planning and reporting, MORT A/I video, print products, special graphics, and SAFE software development.

  16. Amarillo National Resource Center for Plutonium. Quarterly technical progress report, May 1, 1997--July 31, 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    Progress summaries are provided from the Amarillo National Center for Plutonium. Programs include the plutonium information resource center, environment, public health, and safety, education and training, nuclear and other material studies.

  17. Biomass power for rural development. Technical progress report, October 1--December 31, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Neuhauser, E.

    1998-05-01

    The focus of the DOE/USDA sponsored biomass power for rural development project is to develop commercial energy crops for power generation by the year 2000. The New York based Salix Consortium project is a multi-partner endeavor, implemented in three stages. Phase-1, Final Design and Project Development, will conclude with the preparation of construction and/or operating permits, feedstock production plans, and contracts ready for signature. Field trials of willow (Salix) have been initiated at several locations in New York (Tully, Lockport, King Ferry, La Fayette, Massena, and Himrod) and co-firing tests are underway at Greenidge Station (NYSEG) and Dunkirk Station (NMPC). Phase-2 of the project will focus on scale-up of willow crop acreage, construction of co-firing facilities at Dunkirk Station (NMPC), and final modifications for Greenidge Station. Cofiring willow is also under consideration for GPU`s Seward Station where testing is underway. There will be an evaluation of the energy crop as part of the gasification trials occurring at BED`s McNeill Power Station. Phase-3 will represent fullscale commercialization of the energy crop and power generation on a sustainable basis. During the fourth quarter of 1997 the Consortium submitted a Phase-2 proposal. A few of the other more important milestones are outlined below. The first quarter of 1998 will be dominated by pre-planting activity in the spring.

  18. Experimental Program Final Technical Progress Report: 15 February 2007 to 30 September 2012

    Energy Technology Data Exchange (ETDEWEB)

    Kinney, Edward R. [University of Colorado, Boulder, CO

    2014-09-12

    This is the final technical report of the grant DE-FG02-04ER41301 to the University of Colorado at Boulder entitled "Intermediate Energy Nuclear Physics" and describes the results of our funded activities during the period 15 February 2007 to 30 September 2012. These activities were primarily carried out at Fermilab, RHIC, and the German lab DESY. Significant advances in these experiments were carried out by members of the Colorado group and are described in detail.

  19. Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2012

    OpenAIRE

    2013-01-01

    The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology ther...

  20. Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2013

    OpenAIRE

    2014-01-01

    The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomsonscattering. Within fusion technology there...

  1. Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2011

    OpenAIRE

    2012-01-01

    The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark (until 31-12- 2011: Association Euratom – Risø DTU) covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collecti...

  2. Recent Progress in the Study of Circulating Fluidized Bed Hydrodynamics%循环流化床流体动力学研究进展

    Institute of Scientific and Technical Information of China (English)

    朱廷钰; 肖云汉

    2001-01-01

    论述了国内外在循环流化床流体动力学研究领域的进展,对循环流态化颗粒流动问题、颗粒聚集及传热以及循环流态化数学模型等热点问题进行了重点回顾,并指出了当前循环流化床流体动力学研究的一些新动向。%Discussed in this paper is the recent progress in the study both at home and abroad of circulating fluidized bed hydrodynamics. The overview has been focused on a variety of hot topics, such as the problem of circulating fluidized particle flow, particle agglomeration and heat transfer, and a circulating fluidization mathematical model, etc. In addition, some new development trends have been highlighted in the current study of circulating fluidized bed hydrodynamics

  3. Methane from biomass and waste. Annual report for 1984. Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Smith, W.H.

    1985-01-01

    The report summarizes the research conducted in several projects by a wide array of faculty at the University of Florida, researching the production of methane from biomass and waste. Growth and yield data on a wide variety of plant species and varieties in eight plant resource groups are reported on promising species selected from extensive screening trials of over 150 species. Focused intensive research results are summarized for water hyacinth and Napier grass--model species showing yields in excess of 20 dry tons/acre/year. Over 1000 samples were bioassayed for methane yields and the variables affecting conversion to methane were defined. Methanogenesis results covering the spectrum from factors of cellular biology to operating parameters for large digesters. Results emphasize the multiphase Anaerobic Digestion System (MADS) an innovative design that employs leached/packed beds. A comprehensive information management system and an integrated methane form biomass system model (BIOMET) used for research evaluation and program management are described.

  4. Advanced coal conversion process demonstration. Technical progress report, April 1--June 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    This project demonstrates an advanced, thermal, coal upgrading process, coupled with physical cleaning techniques, that is designed to upgrade high moisture, low rank coals to a high quality, low sulfur fuel, registered as the SynCoal{reg_sign} process. The coal is processed through three stages (two heating stages followed by an inert cooling stage) of vibrating fluidized bed reactors that remove chemically bound water, carboxyl groups, and volatile sulfur compounds. After thermal upgrading, the coal is put through a deep bed stratifier cleaning process to separate the pyrite rich ash from the coal. The SynCoal process enhances low rank, western coals, usually with a moisture content of 25 to 55 percent, sulfur content of 0.5 to 1.5 percent, and heating value of 5,500 to 9,000 Btu/lb, by producing a stable, upgraded, coal product with a moisture content as low as 1 percent, sulfur content as low as 0.3 percent, and heating value up to 12,000 Btu/lb. The 45 ton per hour unit is located adjacent to a unit train load out facility at Western Energy Company`s Rosebud coal mine near Colstrip, Montana. The demonstration plant is sized at about one-tenth the projected throughput of a multiple processing train commercial facility. During this report period the primary focus has been to continue the operation of the demonstration facility. Production has been going to area power plants. Modifications and maintenance work was also performed this quarter.

  5. Biomass power for rural development. Technical progress report, May 1, 1996--December 31, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Neuhauser, E.

    1996-02-01

    Developing commercial energy crops for power generation by the year 2000 is the focus of the DOE/USDA sponsored Biomass Power for Rural Development project. The New York based Salix Consortium project is a multi-partner endeavor, implemented in three stages. Phase-I, Final Design and Project Development, will conclude with the preparation of construction and/or operating permits, feedstock production plans, and contracts ready for signature. Field trials of willow (Salix) have been initiated at several locations in New York (Tully, Lockport, King Ferry, La Facette, Massena, and Himrod) and co-firing tests are underway at Greenidge Station (NYSEG). Phase-II of the project will focus on scale-up of willow crop acreage, construction of co-firing facilities at Dunkirk Station (NMPC), and final modifications for Greenidge Station. There will be testing of the energy crop as part of the gasification trials expected to occur at BED`s McNeill power station and potentially at one of GPU`s facilities. Phase-III will represent full-scale commercialization of the energy crop and power generation on a sustainable basis. Willow has been selected as the energy crop of choice for many reasons. Willow is well suited to the climate of the Northeastern United States, and initial field trials have demonstrated that the yields required for the success of the project are obtainable. Like other energy crops, willow has rural development benefits and could serve to diversify local crop production, provide new sources of income for participating growers, and create new jobs. Willow could be used to put a large base of idle acreage back into crop production. Additionally, the willow coppicing system integrates well with current farm operations and utilizes agricultural practices that are already familiar to farmers.

  6. Amarillo National Resource Center for Plutonium. Quarterly technical progress report, November 1, 1997--January 31, 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This report provides information on projects conducted by the Amarillo National Resource Center for Plutonium, a consortium of Texas A&M University, Texas Tech University, and the University of Texas. Progress is reported for four major areas: (1) plutonium information resource; (2) environmental, safety, and health; (3) communication, education, training, and community involvement; and (4) nuclear and other material studies. Environmental, safety, and health projects reported include a number of studies on high explosives. Progress reported for nuclear material studies includes storage and waste disposal investigations.

  7. Instrumentation and process control for fossil demonstration plants. Quarterly technical progress report, January--March 1977

    Energy Technology Data Exchange (ETDEWEB)

    LeSage, L.G.; O' Fallon, N.M.

    1977-09-01

    Progress during the quarter of January through March 1977 on ANL 189a 49622R2, Instrumentation and Process Control for Fossil Demonstration Plants (FDP) is reported. Work has been performed on updating the study of the state-of-the-art of instrumentation for Fossil Demonstration Plants (FDP), on development of mass-flow and other on-line instruments for FDP, process control analysis for FDP, and organization of a symposium on instrumentation and control for FDP. Progress in these areas is described.

  8. Savannah River Ecology Laboratory annual technical progress report of ecological research, period ending July 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Vaitkus, M.R.; Wein, G.R. [eds.; Johnson, G.

    1993-11-01

    This progress report gives an overview of research programs at the Savannah River Site. Topics include; environmental operations support, wood stork foraging and breeding, defense waste processing, environmental stresses, alterations in the environment due to pollutants, wetland ecology, biodiversity, pond drawdown studies, and environmental toxicology.

  9. [Radioisotope thermoelectric generators and ancillary activities]. Monthly technical progress report, 1 April--28 April 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    Tehnical progress achieved during this period on radioisotope thermoelectric generators is described under the following tasks: engineering support, safety analysis, qualified unicouple fabrication, ETG fabrication/assembly/test, RTG shipping/launch support, design/review/mission applications, and project management/quality assurance/reliability.

  10. Electrostatic beneficiation of coal. Quarterly technical progress report, April 1, 1996--June 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Mazumder, M.K.; Lindquist, D.; Tennal, K.B.

    1996-07-01

    Progress reports are presented for the following: modification to the electrostatic separator; review of DOE specifications for minimum beneficiation and calculations of grinding requirements based on washability; two-pass beneficiation; analysis of different sieve fractions; measurement of charge to mass ratio as a function of height of deposition; and charging of coal against different materials.

  11. Projects at the Western Environmental Technology Office. Quarterly technical progress report, January 1--March 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    This quarterly report briefly describes recent progress in eight projects. The projects are entitled Biomass Remediation Project; Heavy Metal-Contaminated Soil Project; MHD Shutdown; Mine Waste Technology Program; Plasma Projects; Resource Recovery Project; Spray Casting Project; and Watervliet Arsenal Project.

  12. Dissolved organic matter and lake metabolism. Technical progress report, 1 July 1975--30 June 1976

    Energy Technology Data Exchange (ETDEWEB)

    Wetzel, R. G.

    1976-01-01

    Progress is reported in the following areas of research: interactions of dissolved organic matter with inorganic nutrient cycling; regulation of the photosynthetic and decompositional metabolism of micro- and macroflora; regulatory mechanisms of growth and rates of carbon cycling; and fate of detrital dissolved and particulate organic matter. (HLW)

  13. Great Basin paleoenvironmental studies project; Technical progress report: First quarter (January--August 1993)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    Project goals, project tasks, progress on tasks, and problems encountered are described and discussed for each of the studies that make up the Great Basin Paleoenvironmental Studies Project for Yucca Mountain. These studies are: Paleobotany, Paleofauna, Geomorphology, and Transportation. Budget summaries are also given for each of the studies and for the overall project.

  14. Projects at the Western Environmental Technology Office. Quarterly technical progress report, January 1--March 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    This quarterly report briefly describes recent progress in eight projects. The projects are entitled Biomass Remediation Project; Heavy Metal-Contaminated Soil Project; MHD Shutdown; Mine Waste Technology Program; Plasma Projects; Resource Recovery Project; Spray Casting Project; and Watervliet Arsenal Project.

  15. Energy conservation in citrus processing. Technical progress report No. 2, April 1, 1980-February 28, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Leo, M.A.; Lari, R.I.; Moore, N.R.; Broussard, M.R.; Gyamfi, M.

    1981-03-15

    Systems that reduce energy usage and are economically viable in the citrus fruit processing industry are identified. The preliminary results of Phase I are presented. Alternative systems to be considered are classified and denoted as central, modular, integrated, and combined. Progress is reported on the central and modular systems. (MCW)

  16. Review of technical program and progress. LBL geothermal exploration technology development program, FY 1982

    Energy Technology Data Exchange (ETDEWEB)

    Goldstein, N.E.

    1982-01-01

    The objectives, method of approach, main program elements, and progress through FY 1982 for Geothermal Exploration Technology Program at LBL are reviewed. Current tasks include controlled-source electromagnetic research, seismological research, magnetotelluric research, and electromagnetic technique evaluation and numerical modeling.

  17. [Tampa Electric Company IGCC project]. Final public design report; Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-07-01

    This final Public Design Report (PDR) provides completed design information about Tampa Electric Company`s Polk Power Station Unit No. 1, which will demonstrate in a commercial 250 MW unit the operating parameters and benefits of the integration of oxygen-blown, entrained-flow coal gasification with advanced combined cycle technology. Pending development of technically and commercially viable sorbent for the Hot Gas Cleanup System, the HGCU also is demonstrated. The report is organized under the following sections: design basis description; plant descriptions; plant systems; project costs and schedule; heat and material balances; general arrangement drawings; equipment list; and miscellaneous drawings.

  18. Molecular biological enhancement of coal biodesulfurization. Ninth quarterly technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Litchfield, J.H.; Zupancic, T.J.; Baker, B.; Palmer, D.T.; Fry, I.J.; Tranuero, C.G.; Wyza, R.E.; Schweitzer, A.; Conkle, H.N. [Battelle, Columbus, OH (United States); Chakravanty, L.; Tuovinen, O.H. [Ohio State Univ., Columbus, OH (United States)

    1991-09-13

    The objective of this project is to produce one or more microorganisms capable of removing the organic and inorganic sulfur in coal. The original specific technical objectives of the project were to: clone and characterize the genes encoding the enzymes of the ``4S`` pathway (sulfoxide/sulfone/sulfonate/sulfate) for release of organic sulfur from coal; return multiple copies of genes to the original host to enhance the biodesulfurization activity of that organism; transfer this pathway into a fast-growing chemolithotropic bacterium; conduct a batch-mode optimization/analysis of scale-up variables.

  19. Molecular biological enhancement of coal desulfurization. Eleventh quarterly technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Litchfield, J.H.; Zupancic, T.J.; Kittle, J.D. Jr.; Baker, B.; Palmer, D.T.; Traunero, C.G.; Wyza, R.E.; Schweitzer, A.; Conkle, H.N. [Battelle, Columbus, OH (United States); Chakravarty, L.; Tuovinen, O.H. [Ohio State Univ., Columbus, OH (United States)

    1991-03-13

    The objective of this project is to produce one or more microorganisms capable of removing the organic and inorganic sulfur in coal. The original specific technical objectives of the project were to: clone and characterize the genes encoding the enzymes of the ``4S`` pathway (sulfoxide/sulfone/sulfonate/sulfate) for release of organic sulfur from coal; return multiple copies of genes to the original host to enhance the biodesulfurization activity of the organism; transfer this pathway into a fast-growing chemolithotrophic bacterium; conduct a batch-mode optimization/analysis of scale-up variables.

  20. Molecular biological enhancement of coal biodesulfurization. Tenth quarterly technical progress report, [September--December 1991

    Energy Technology Data Exchange (ETDEWEB)

    Litchfield, J.H.; Zupancic, T.J.; Kittle, J.D.; Baker, B.; Palmer, D.T.; Fry, I.J.; Traunero, C.G.; Wyza, R.E.; Schweitzer, A.; Conkle, H.N. [Battelle, Columbus, OH (United States); Chakravanty, L.; Tuovinen, O.H. [Ohio State Univ., Columbus, OH (United States)

    1991-12-13

    The objective of this project is to produce one or more microorganisms capable of removing the organic and inorganic sulfur in coal. The specific technical objectives of the project are to: clone and characterize the genes encoding the enzymes of the ``4S`` pathway (sulfoxide/sulfone/sulfonate/sulfate) for release of organic sulfur from coal; return multiple copies of genes to the original host to enhance the biodesulfurization activity of that organism; transfer this pathway into a fast-growing chemolithotrophic bacterium; and conduct a batch-mode optimization/analysis of scale-up variables.

  1. Molecular biological enhancement of coal biodesulfurization. Fourth quarterly technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Litchfield, J.H.; Fry, I.; Wyza, R.E.; Palmer, D.T.; Zupancic, T.J.; Conkle, H.N.

    1990-06-14

    The objective of this project is to produce one or more microorganisms capable of removing the organic and inorganic sulfur in coal. The original specific technical objectives of the project were to: clone and characterize the genes encoding the enzymes of the ``4S`` pathway (sulfoxide/sulfone/sulfonate/sulfate) for release of organic sulfur from coal; return multiple copies of genes to the original host to enhance the biodesulfurization activity of that organism; transfer this pathway into a fast-growing chemolithotropic bacterium; conduct a batch-mode optimization/analysis of scale-up variables.

  2. "Optimal design and routing of power lines; ecological, technical and economic perspectives” (OPTIPOL). Progress Report 2009

    OpenAIRE

    Bevanger, Kjetil Modolv; Bartzke, Gundula; Brøseth, Henrik; Gjershaug, Jan Ove; Hanssen, Frank Ole; Jacobsen, Karl Otto; Kvaløy, Pål; May, Roelof Frans; Nygård, Torgeir; Pedersen, Hans-Christian; Reitan, Ole; Refsnæs, Steinar; Stokke, Sigbjørn; Vang, Roald

    2009-01-01

    From 2009 inclusive, NINA has received economic support for research on power lines and wildlife from the Norwegian Research Council (NFR) through the RENERGI Programme. The project is named “Optimal design and routing of power lines; ecological, technical and eco-nomic perspectives” (OPTIPOL). It is scheduled for 5 years (2009-1013) and is part of the ac-tivities within CEDREN, i.e. the Centre for environmental design of renewable energy (cf. http://www.cedren.no). With a grid close to 200 0...

  3. New infrared photon absorption processes. Final technical progress report, August 1, 1988--February 1, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Bayfield, J.E.

    1993-05-01

    The fast ionization of atoms by very short laser pulses, and its possible suppression at extreme pulse intensities, is an active new field of investigation at present. Described is an investigation of whether past techniques for infrared laser multiphoton ionization of excited hydrogen atoms and of one-dimensional microwave ionization of highly excited hydrogen atoms can be combined and extended to address the new issues. Although technically difficult and requiring further improvement of apparatus, intense-field infrared laser experiments on excited hydrogen atoms are possible and can directly test theoretical and numerical results.

  4. Measurements of scattering processes in negative ion-atom collisions. Technical progress report, 1 September 1992--31 August 1993

    Energy Technology Data Exchange (ETDEWEB)

    Kvale, T.J.

    1993-05-01

    This Technical Progress Report describes the progress made on the research objectives during the past twelve months. This research project is designed to provide measurements of various scattering processes which occur in H{sup {minus}} collisions with atomic (specifically, noble gas and atomic hydrogen) targets at intermediate energies. These processes include elastic scattering, single- and double-electron detachment, and target excitation/ionization. For the elastic and target inelastic processes where H{sup {minus}} is scattered intact, the experimental technique of Ion Energy-Loss Spectroscopy (IELS) will be employed to identify the final target state(s). In most of the above processes, cross sections are unknown both experimentally and theoretically. The measurements in progress will provide either experimentally determined cross sections or set upper limits to those cross sections. In either case, these measurements will be stringent tests of our understanding in energetic negative ion - atom collisions. In addition secondary negative particle emission yields for H{sup 0} on Cu in the 3 to 50 keV range are shown.

  5. Measurements of scattering processes in negative ion-atom collisions. Technical progress report, 1 September 1991--31 August 1992

    Energy Technology Data Exchange (ETDEWEB)

    Kvale, T.J.

    1992-04-01

    This Technical Progress Report describes the progress made on the research objectives during the past twelve months. This research project is designed to provide measurements of various scattering processes which occur in H{sup {minus}} collisions with atomic (specifically, noble gas and atomic hydrogen) targets at intermediate energies. These processes include: elastic scattering,single- and double-electron detachment, and target excitation/ionization. For the elastic and target inelastic processes where H{sup {minus}} is scattered intact, the experimental technique of Ion Energy-Loss Spectroscopy (IELS) will be employed to identify the final target state(s). In most of the above processes, cross sections are unknown both experimentally and theoretically. The measurements in progress will provide either experimentally-determined cross sections or set upper limits to those cross sections. In either case, these measurements will be stringent tests of our understanding in energetic negative ion-atom collisions. This series of experiments required the construction of a new facility and the initial ion beam was accelerated through the apparatus in April 1991.

  6. Developments of advanced hot-gas desulfurization sorbents. Quarterly technical progress report, April--June 1995

    Energy Technology Data Exchange (ETDEWEB)

    Jothimurugesan, K.; Adeyiga, A.A.; Gangwal, S.K.

    1995-07-01

    The objectives of this project are to develop hot-gas cleanup sorbents for relatively lower temperature application, with emphasis on the temperature range from 343-538{degrees}C. The candidate sorbents include highly dispersed mixed metal oxides of zinc, iron, copper, cobalt and molybdenum. The specific objective in the successful preparation of H{sub 2}S absorbents will be to generate as high and as stable a surface area as possible, in order to develop suitable sorbent, that are sufficiently reactive and regenerable at the relatively lower temperatures of interest in this work. A number of formulations will be prepared and screened for testing in a 1/2-inch fixed bed reactor at high pressure (1 to 20 atm) and high temperatures using simulated coal-derived fuel-gases. Screening criteria will include, chemical reactivity, stability, and regenerability over the temperature range of 343{degrees}C (650{degrees}F) to 538{degrees}C (1000{degrees}F). Each formulation will be tested for up to 5 cycles of absorption and regeneration. To prevent sulfation, catalyst additives will be investigated, which would promote a lower ignition of the regeneration. Selected superior formulation will be tested for long term (up to least 30 cycles) durability and chemical reactivity in the reactor.

  7. Power systems development facility. Quarterly technical progress report, July 1, 1994--September 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    The objective of this project is to evaluate hot gas particle control technologies using coal-derived gas streams. This will entail the design, construction, installation, and use of a flexible test facility which can operate under realistic gasification and combustion conditions. The major particulate control device issues to be addressed include the integration of the particulate control devices into coal utilization systems, on-line cleaning techniques, chemical and thermal degradation of components, fatigue or structural failures, blinding, collection efficiency as a function of particle size, and scale-up of particulate control systems to commercial size. The conceptual design of the facility was extended to include a within scope, phased expansion of the existing Hot Gas Cleanup Test Facility Cooperative Agreement to also address systems integration issues of hot particulate removal in advanced coal-based power generation systems. This expansion included the consideration of the following modules at the test facility in addition to the original Transport Reactor gas source and Hot Gas Cleanup Units: (1) Carbonizer/Pressurized Circulating Fluidized Bed Gas Source. (2) Hot Gas Cleanup Units to mate to all gas streams. (3) Combustion Gas Turbine. (4) Fuel Cell and associated gas treatment. This expansion to the Hot Gas Cleanup Test Facility is herein referred to as the Power Systems Development Facility (PSDF).

  8. Field-simulation analysis for disposal of liquefaction solid waste. Third quarterly technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    1982-08-27

    The tasks to be performed in this study are: (1) review applicable RCRA documents; (2) select waste and site-related parameters of interest; (3) compare and recommend leachate test methods; (4) review predictive simulation models and select one or more for further development; (5) identify required field verification data; and (6) develop a field monitoring program to obtain these data. This report represents the third quarterly progress report and contains the text prepared to date under Task 4.

  9. U.C. Davis high energy particle physics research: Technical progress report -- 1990

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-12-31

    Summaries of progress made for this period is given for each of the following areas: (1) Task A--Experiment, H1 detector at DESY; (2) Task C--Experiment, AMY detector at KEK; (3) Task D--Experiment, fixed target detectors at Fermilab; (4) Task F--Experiment, PEP detector at SLAC and pixel detector; (5) Task B--Theory, particle physics; and (6) Task E--Theory, particle physics.

  10. Association Euratom - Risoe National Laboratory, Technical Univ. of Denmark. Annual progress report 2007

    Energy Technology Data Exchange (ETDEWEB)

    Michelsen, P.K.; Korsholm, S.B.; Rasmussen, J.J. (eds.)

    2008-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. The activities in technology on investigations of radiation damage of fusion reactor materials have been phased out during 2007. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2007. (Author)

  11. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2008

    Energy Technology Data Exchange (ETDEWEB)

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M. (eds.)

    2009-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. New activities in technology related to development of high temperature superconductors have been initiated in 2008. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2008. (Author)

  12. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2010

    Energy Technology Data Exchange (ETDEWEB)

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M. (eds.)

    2011-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Other activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2010. (Author)

  13. Molecular biological enhancement of coal biodesulfurization. Eleventh quarterly technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Litchfield, J.H.; Zupancic, T.J.; Kittle, J.D. Jr.; Baker, B.; Palmer, D.T.; Traunero, C.G.; Wyza, R.E.; Schweitzer, A.; Conkle, H.N. [Battelle, Columbus, OH (United States); Chakravarty, L.; Tuovinen, O.H. [Ohio State Univ., Columbus, OH (United States)

    1992-03-13

    The objective of this project is to produce one or more microorganisms capable of the organic and inorganic sulfur in coal. The original specific technical objectives of the project were to: (1) clone and characterize the genes encoding the enzymes of the ``4S`` pathway (sulfoxide/sulfone/sulfonate/sulfate) for release of organic sulfur from coal; (2) return multiple copies of genes to the original host to enhance the biodesulfurization activity of that organism; (3) transfer this pathway into a fast-growing chemolithotrophic bacterium; (4) conduct a batch-mode optimization/analysis of scale-up variables. By letter of September 3, 1991, from the Project Manager at Department of Energy, Pittsburgh Energy Technology Center, these objectives of this project were redirected toward finding and developing suitable vectors for Thiobacillus strains. All work on bacterial strains from Lehigh University was terminated since they did not contain desulfurization traits represented by the ``4S`` pathway.

  14. Redwood Community Action Agency: Technical progress report, 4th quarter, 1986

    Energy Technology Data Exchange (ETDEWEB)

    1986-01-01

    Redwood Community Action Agency (RCAA) has been developing a business plan for a shared-savings energy business under this grant since January, 1986. At this time RCAA is nearing completion of the research activities, although a 90 day no-cost extension has been requested and received to complete activities on this grant. All consultant reports on the technical feasibility analysis and market research activities have been completed at this time. Fifteen thousand dollars of equity capital has been allocated for the business venture being investigated under this grant through an equity grant from the California Department of Economic Opportunity. This money, combined with agency unrestricted funds, will provide the initial seed capital for the venture.

  15. The Progression of Podcasting/Vodcasting in a Technical Physics Class

    Science.gov (United States)

    Glanville, Y. J.

    2010-11-01

    Technology such as Microsoft PowerPoint presentations, clickers, podcasting, and learning management suites is becoming prevalent in classrooms. Instructors are using these media in both large lecture hall settings and small classrooms with just a handful of students. Traditionally, each of these media is instructor driven. For instance, podcasting (audio recordings) provided my technical physics course with supplemental notes to accompany a traditional algebra-based physics lecture. Podcasting is an ideal tool for this mode of instruction, but podcasting/vodcasting is also an ideal technique for student projects and student-driven learning. I present here the various podcasting/vodcasting projects my students and I have undertaken over the last few years.

  16. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2009

    Energy Technology Data Exchange (ETDEWEB)

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M. (eds.)

    2010-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2009. (Author)

  17. West Hackberry Tertiary Project. Quarterly technical progress report, September 3, 1993--December 3, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Fassihi, M.R.; Gillham, T.H.

    1993-11-30

    The goal of the West Hackberry Tertiary Project is to demonstrate the technical and economic feasibility combining air injection with the Double Displacement Process for tertiary oil recovery. The Double Displacement Process is the gas displacement of a water invaded oil column for the purpose of recovering oil through gravity drainage. The novel aspect of this project is the use of air as the injection fluid. The target reservoirs for the project are the Camerina C- 1,2,3 Sands located on the west flank of West Hackberry Field in Cameron Parish, Louisiana. If successful, this project win demonstrate that the use of air injection in the Double Displacement Process can economically recover oil in reservoirs where tertiary oil recovery is presently uneconomical.

  18. West Hackberry Tertiary Project. Quarterly technical progress report, March 3, 1993--June 3, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Gillham, T.H.

    1994-09-01

    The goal of the West Hackberry Tertiary Project is to demonstrate the technical and economic feasibility of combining air injection with the Double Displacement Process for tertiary oil recovery. The Double Displacement Process is the gas displacement of a water invaded oil column for the purpose of recovering oil through gravity drainage. The novel aspect of this project is the use of air as the injection fluid. The target reservoir for the project is the Camerina C-1,2,3 Sand located on the West Flank of West Hackberry Field in Cameron Parish, Louisiana. This reservoir has been unitized and is designated as the WH Cam C RI SU. If successful, this project will demonstrate that the use of air injection in the Double Displacement Process can economically recover oil in reservoirs where tertiary oil recovery is presently uneconomic.

  19. Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol. 11, No. 1--Vol. 17, No. 6

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, W.B.; Klein, A.

    1977-02-23

    This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970), through Vol. 17, No. 6 (Nov.-Dec. 1976). The index includes a chronological list of articles (including abstract) followed by KWIC and Author Indexes. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 350 technical articles in the last six years of publication.

  20. Engineering support services for the DOE/GRI coal gasification research program. Quarterly technical progress report, January-March 1982

    Energy Technology Data Exchange (ETDEWEB)

    Bostwick, L.E.; Ethridge, T.R.; Starr, D.W.; Koneru, P.B.; Hubbard, D.A.; Shah, K.V.; Smith, M.R.; Ward, W.E.; Wong, E.W.

    1982-05-01

    Kellogg continued to actively monitor operations at BI-GAS, Westinghouse and IGT (for peat gasification). Pilot plant/PDU test runs which were monitored and reported included BI-GAS Tests G-18, G-18A and G-18B; Westinghouse PDU Test TP-032-1 and CFSF Test TP-M003; and Peatgas Pilot Plant Test No. 5. Kellogg also monitored winterization/maintenance activities at BI-GAS and Westinghouse and precommissioning of the IGT Wet Carbonization PDU. The final report on the Hygas Data Base Evaluation was issued, while final revisions were completed for the reports concerning PDU data base evaluations of Peatgas and single-stage peat gasification. Efforts toward completion of the brochure describing the DOE/GRI Joint Program proceeded. Normal MPC activities continued. Several technical progress reports were issued during this quarter.

  1. Management of dry flue gas desulfurization by-products in underground mines. Quarterly technical progress report, April 1995--June 1995

    Energy Technology Data Exchange (ETDEWEB)

    Chugh, Y.P.; Dutta, D.; Esling, S. [and others

    1995-07-01

    On September 30, 1993, the U.S. Department of Energy-Morgantown Energy Technology Center and Southern Illinois University at Carbondale (SIUC) entered into a cooperative research agreement entitled {open_quotes}Management of Dry Flue Gas Desulfurization By-Products in Underground Mines{close_quotes} (DE-FC21-93MC30252). Under the agreement Southern Illinois University at Carbondale will develop and demonstrate several technologies for the placement of coal combustion residues in abandoned coal mines, and will assess the environmental impact of such underground residues placement. Previous quarterly Technical Progress Reports have set forth the specific objectives of the program, and a discussion of these is not repeated here. Rather, this report discusses the technical progress made during the period April 1 - June 30, 1995. A final topical report on the SEEC, Inc. demonstration of its technology for the transporting of coal combustion residues was completed during the quarter, although final printing of the report was accomplished early in July, 1995. The SEEC technology involves the use of Collapsible Intermodal Containers (CIC`s) developed by SEEC, and the transportation of such containers - filled with fly ash or other coal combustion residues - on rail coal cars or other transportation means. Copies of the final topical report, entitled {open_quotes}The Development and Testing of Collapsible Intermodal Containers for the Handling and Transport of Coal Combustion Residues{close_quotes} were furnished to the Morgantown Energy Technology Center. The Rapid Aging Test colums were placed in operation during the quarter. This test is to determine the long-term reaction of both the pneumatic and hydraulic mixtures to brine as a leaching material, and simulates the conditions that will be encountered in the actual underground placement of the coal combustion residues mixtures. The tests will continue for about one year.

  2. Quarterly technical progress report for the period ending June 30, 1984

    Energy Technology Data Exchange (ETDEWEB)

    1984-10-01

    The Magnetohydrodynamics Program (Component Development and Integration Facility) in Butte, Montana, continued its site preparation for the TRW first-stage combustor installation. In the area of flue gas cleanup, our in-house research program is continuing its investigation into the causes of sorbent attrition in PETC's fluidized-bed copper oxide process for simultaneous SO/sub 2//NO/sub x/ removal. Interwoven with these tests is a series of spray dryer/electrostatic precipitator tests that are being conducted with the cooperation of Wheelabrator-Frye, Inc. This test series was completed this quarter, and the data show that when using a Kentucky coal, Wheelabrator-Frye's electrostatic precipitator provides excellent particulate control efficiency while using a spray dryer for sulfur dioxide removal. A unique project at Carnegie-Mellon University is looking at the concept of integrated environmental control for coal-fired power plants making use of precombustion, combustion, and postcombustion control, including systems for the simultaneous removal of more than one pollutant. The objective of this research is to develop a computer model and assessment for integrated environmental control systems that utilize conventional or advanced systems. The Liquid Phase Methanol Project Development Unit in LaPorte, Texas, was restarted after a successful shakedown run was completed. PETC has recently begun an in-house research project aimed at exploring the basic chemistry of liquefying coal in the presence of water under supercritical conditions. In the Alternative Fuels Technology Program, the Gulf Research and Development Company has completed the preliminary testing phase of its erosion test loop. Their results indicate that when pumping a coal-water slurry fuel through a flow loop, the erosion rate increases as velocity increases, suggesting a well-defined relationship between these two parameters.

  3. Quarterly technical progress report for the period ending June 30, 1984

    Energy Technology Data Exchange (ETDEWEB)

    1984-10-01

    The Magnetohydrodynamics Program (Component Development and Integration Facility) in Butte, Montana, continued its site preparation for the TRW first-stage combustor installation. In the area of flue gas cleanup, our in-house research program is continuing its investigation into the causes of sorbent attrition in PETC's fluidized-bed copper oxide process for simultaneous SO/sub 2//NO/sub x/ removal. Interwoven with these tests is a series of spray dryer/electrostatic precipitator tests that are being conducted with the cooperation of Wheelabrator-Frye, Inc. This test series was completed this quarter, and the data show that when using a Kentucky coal, Wheelabrator-Frye's electrostatic precipitator provides excellent particulate control efficiency while using a spray dryer for sulfur dioxide removal. A unique project at Carnegie-Mellon University is looking at the concept of integrated environmental control for coal-fired power plants making use of precombustion, combustion, and postcombustion control, including systems for the simultaneous removal of more than one pollutant. The objective of this research is to develop a computer model and assessment for integrated environmental control systems that utilize conventional or advanced systems. The Liquid Phase Methanol Project Development Unit in LaPorte, Texas, was restarted after a successful shakedown run was completed. PETC has recently begun an in-house research project aimed at exploring the basic chemistry of liquefying coal in the presence of water under supercritical conditions. In the Alternative Fuels Technology Program, the Gulf Research and Development Company has completed the preliminary testing phase of its erosion test loop. Their results indicate that when pumping a coal-water slurry fuel through a flow loop, the erosion rate increases as velocity increases, suggesting a well-defined relationship between these two parameters.

  4. Instrumentation and process control for fossil demonstration plants. Quarterly technical progress report, October--December 1976

    Energy Technology Data Exchange (ETDEWEB)

    LeSage, L. G.; O' Fallon, N. M; Bump, T. R.; Cohn, C. E.; Doering, R. W.; Duffey, D.; Kirsch,; Lipinski, W. C.; Managan, W. W.; Porges, K. G.; Raptis, A. C.

    1977-01-01

    The final report of the state-of-the-art study of instrumentation for process control and safety in large-scale coal conversion and fluidized-bed combustion systems was distributed in November. A conceptual design for the Solids/Gas Flow Test Facility has been initiated, the major components identified, and vendors located. Work on acoustic flow measurement has included theoretical feasibility studies of acoustic/ultrasonic techniques for mass-flow measurements of slurries and solid/gas media. Initial planning was conducted to establish a laboratory facility necessary to verify theoretical findings. A survey of the literature relating to capacitive measurements was begun to provide a basis for conceptual designs and preliminary bench tests of the feasibility of these designs. Conceptual design of a capacitive on-line solids density measuring device and calculations to select the type of system for initial feasibility tests were carried out. Preliminary tests of neutron capture gamma analysis for on-line elemental composition of liquid and solid streams in coal plants indicate that most coal elements can be detected quantitatively through the pipe walls. A computer program for peak-fitting in the gamma spectrum was modified for requirements of this work. A literature search was started to determine the state-of-the-art in dynamic process modeling of fossil energy system components, physical property models, and process control models. A partial review of abstracts from a computerized literature search has identified over 50 references having possible application to process analysis activities in this program.

  5. Technical Progress Report on Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Bill Stanley; Patrick Gonzalez; Sandra Brown; Jenny Henman; Ben Poulter; Sarah Woodhouse Murdock; Neil Sampson; Tim Pearson; Sarah Walker; Zoe Kant; Miguel Calmon; Gilberto Tiepolo

    2006-06-30

    The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between April 1st and July 30th 2006. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: emerging technologies for remote sensing of terrestrial carbon; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool. Work is being carried out in Brazil, Belize, Chile, Peru and the USA.

  6. Base program on energy related research. Quarterly technical progress report, February--April 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-01

    Progress reports are briefly described for the following areas of research: oil and gas; advanced systems applications; environmental technologies; and applied energy science. Oil and gas research includes: CROW {sup TM} process modeling; and miscible-immiscible gas injection processes. Advanced systems applications covers: development and optimization of a process for the production of a premium sold fuel from western US coals; development of an on-line alkali monitoring probe; optimization of the recycle oil process for eastern oil shale; and process support and development. Environmental technologies has solid waste management; and remediation of contaminated soils.

  7. Fusion programs in applied plasma physics. Technical progress report, July 11, 1992--May 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-07-01

    This report summarizes the progress made in theoretical and experimental research funded by US Department of Energy Grant No. DE-FG03-92ER54150, during the period July 11, 1992 through May 31, 1993. Four main tasks are reported: applied plasma physics theory, alpha particle diagnostic, edge and current density diagnostic, and plasma rotation drive. The report also discusses the research plans for the theory and experimental programs for the next grant year. Reports and publications supported by the grant during this period are listed in the final section.

  8. Decontamination Systems Information and Research Program. Quarterly technical progress report, July 1--September 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-01

    Progress reports are presented for the following projects: systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies--drain-enhanced soil flushing (DESF) for organic contaminants removal; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors--monolayer and multilayer self-assembled films for chemical sensors; Winfield Lock and Dam remediation; Winfield cleanup survey; assessment of technologies for hazardous waste site remediation--non-treatment technologies and pilot scale test facility implementation; assessment of environmental remediation storage technology; assessment of environmental remediation excavation technology; assessment of environmental remediation monitoring technology; and remediation of hazardous sites with steam reforming.

  9. GPHS-RTGs in support of the Cassini RTG Program. Semi annual technical progress report, September 26, 1994--April 2, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-20

    The technical progress achieved during the period 26 September 1994 through 2 April 1995 on Contract DE-AC03-91SF18852 Radioisotope Thermoelectric Generators and Ancillary Activities is described herein. Monthly technical activity for the period 27 February 1995 through 2 April 1995 is included in this progress report. The report addresses tasks, including: spacecraft integration and liaison; engineering support; safety; qualified unicouple production; ETG Fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and CAGO maintenance and repair; and CAGO acquisition (capital funds).

  10. Silicon ribbon growth by a capillary action shaping technique. Quarterly technical progress report No. 2

    Energy Technology Data Exchange (ETDEWEB)

    Schwuttke, G.H.; Ciszek, T.F.; Kran, A.

    1975-01-01

    Progress during the second quarter of the contractual effort is described. The work performed related mainly to ribbon growth by a capillary action shaping technique and to ribbon characterization. Actual progress in the crystal growth area includes the evaluation of 10 potential die materials other than carbon and the process development for 25-mm-wide ribon. From the die study it is concluded that boron carbide, silicon carbide, and silicon nitride may warrant further investigation as die materials. Process development for 25-mm ribbon growth resulted in ribbons of superior surface quality. Potential ribbongrowth problems encountered and discussed include a boron doping anomaly and frozen-in stresses in ribbons. The characterization effort concentrated on the development of a solar-cell process to be used for ribbon characterization. Material requirements and detailed process procedures are given. Solar cells fabricated by this process are compared with commercially available solar cells and compare favorably. A transmission electron microscopy study of planar boundaries frequently observed in ribbon crystals is reported. (auth)

  11. Savannah River Ecology Laboratory. Annual technical progress report of ecological research

    Energy Technology Data Exchange (ETDEWEB)

    Smith, M.H.

    1996-07-31

    The Savannah River Ecology Laboratory (SREL) is a research unit of the University of Georgia (UGA). The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts basic and applied ecological research, as well as education and outreach programs, under a contract with the U.S. Department of Energy (DOE) at the Savannah River Site (SRS) near Aiken, South Carolina. Significant accomplishments were made during the past year in the areas of research, education and service. The Laboratory`s research mission was fulfilled with the publication of two books and 143 journal articles and book chapters by faculty, technical and students, and visiting scientists. An additional three books and about 80 journal articles currently are in press. Faculty, technician and students presented 193 lectures, scientific presentations, and posters to colleges and universities, including minority institutions. Dr. J Vaun McArthur organized and conducted the Third Annual SREL Symposium on the Environment: New Concepts in Strewn Ecology: An Integrative Approach. Dr. Michael Newman conducted a 5-day course titled Quantitative Methods in Ecotoxicology, and Dr. Brian Teppen of The Advanced Analytical Center for Environmental Sciences (AACES) taught a 3-day short course titled Introduction to Molecular Modeling of Environmental Systems. Dr. I. Lehr Brisbin co-hosted a meeting of the Crocodile Special Interest Group. Dr. Rebecca Sharitz attended four symposia in Japan during May and June 1996 and conducted meetings of the Executive Committee and Board of the International Association for Ecology (ENTECOL).

  12. Pulverized coal firing of aluminum melting furnaces. First annual technical progress report, May 1978-June 1979

    Energy Technology Data Exchange (ETDEWEB)

    West, C.E.; Hines, J.E.; Stewart, D.L. Jr.; Yu, H.

    1979-10-01

    The ultimate objective of this program is the commercial demonstration of an efficient, environmentally acceptable coal firing process suitable for implementation on melting furnaces throughout the aluminum industry. To achieve this goal, the program has been divided into two phases. Phase I has begun with the design and construction of a 350 lb/h (coal) staged slagging cyclone combustor (SSCC) attached to a 7-ft dia aluminum melting ladle furnace. Process development will culminate with a 1000 pph prototype SSCC firing a 40,000 lb capacity open hearth melting furnace at the Alcoa Laboratories. Phase II implementation is currently planned for Alcoa's Lafayette, IN, Works, where two of the ingot plant's five open hearth melting furnaces will be converted to utilize coal. In addition to confirmation of data gathered in Phase I, the effect of extended production schedule operation on equipment and efficiencies will be determined. This work would begin in 1982 pursuant to technical and economic evaluation of the process development at that time. A major design subcontract for assistance in the design of the SSCC is 80% completed.

  13. Progress in magnetically stabilized bed and magnetic catalyst%磁稳定床及磁性催化剂的研究进展

    Institute of Scientific and Technical Information of China (English)

    鲁威; 文庆; 袁华; 吴元欣

    2012-01-01

    The research progress in the application of magnetically stabilized bed ( MSB) in the fields of petrochemical and biology was reviewed. MSB is used in catalytic hydrogenation, dust removal, dry coal separation, biochemical separation, immobilized bioreactors and culture of cells, etc. Compared with the conventional process, this novel reactor combines the advantages of fixed bed reactor and fluidized bed reactor, which can intensify the internal mass and heat transfer and improve the reaction efficiency. The design of magnetic catalyst is the key to the application of the MSB. So far,the magnetic catalysts in MSB are more commonly in coreshell structure with the magnetic core. All these catalysts have excellent magnetic properties and good catalytic performance at lower temperature. The research and development of MSB and magnetic catalyst are promising in catalyst industry.%对磁稳定床及磁性催化剂在石油化工和生物工程等领域的应用进行了归纳总结.磁稳定床已经应用于催化加氢、烟尘净化、干法选煤、生化分离、固定化生物反应器、细胞培养等过程.与传统工艺相比,磁稳定床兼有固定床和流化床的优点,能强化受传质传热限制的反应过程,提高反应效率,在实际应用中显示出独特的优越性.磁性催化剂的设计与开发是磁稳定床应用的关键,目前磁性催化剂以包覆型催化剂为主,其共同特点是具有适宜的磁性和低温反应活性,利于反应操作.磁稳定床及其磁性催化剂的研究开发是催化剂工业发展的一个新方向.

  14. Dissolved organic matter and lake metabolism. Technical progress report, 1 July 1976--30 June 1977

    Energy Technology Data Exchange (ETDEWEB)

    Wetzel, R.G.

    1977-01-01

    Progress is reported on investigations on the qualitative and quantitative cycling of particulate and dissolved organic matter within lakes and their drainage basins. Interactions of dissolved organic matter with inorganic nutrient cycling and regulation of the photosynthetic and decompositional metabolism of micro- and macroflora remain the focal point of these studies. Major efforts were directed towards the sources fates, pathways, and interactions of dissolved organic matter in inorganic chemical cycling; allochthonous sources, metabolism en route, and inputs to the lake systems of increasing stages of eutrophication; and the relationships of these compounds to the nutrient physiology and metabolism of phytoplankton, sessile algae, macrophytes, and bacterial populations. Results of studies carried out in a freshwater lake in Michigan (Lawrence Lake) are reported. 165 references.

  15. New imaging systems in nuclear medicine. Technical progress report, October 1, 1976--May 31, 1977

    Energy Technology Data Exchange (ETDEWEB)

    Brownell, G.L.

    1977-01-01

    Work carried out on the development of instrumentation and techniques for positron scintigraphy is discussed. Progress in positron imaging instrumentation and applications is detailed. The assembly and initial evaluation of the new multicrystal positron camera, PC-II, has been completed. Images have been obtained in both two and three-dimensions which demonstrate the basic physical properties of the instrument. Successful measurements using transverse section imaging have been carried out on animals and human volunteers. Physiological investigation using PC-II is proceeding. A flexible and accurate computer program has been developed for transverse section reconstruction of data acquired by PC-II. This program makes it possible to reconstruct both the activity distribution and the distribution of absorption. The program has been developed in such a way that it can handle variations in the data collection procedure. Clinical studies using PC-I and PC-II are being carried on in areas of heart, lung and brain.

  16. [Geothermal system temperature-depth database and model for data analysis]. 5. quarterly technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Blackwell, D.D.

    1998-04-25

    During this first quarter of the second year of the contract activity has involved several different tasks. The author has continued to work on three tasks most intensively during this quarter: the task of implementing the data base for geothermal system temperature-depth, the maintenance of the WWW site with the heat flow and gradient data base, and finally the development of a modeling capability for analysis of the geothermal system exploration data. The author has completed the task of developing a data base template for geothermal system temperature-depth data that can be used in conjunction with the regional data base that he had already developed and is now implementing it. Progress is described.

  17. Instrumentation and process control for fossil demonstration plants. Annual technical progress report, October 1976--September 1977

    Energy Technology Data Exchange (ETDEWEB)

    LeSage, L. G.; O' Fallon, N. M.

    1977-10-01

    Progress on Instrumentation and Process Control for Fossil Demonstration Plants (FDP) is reported. Work has been performed on updating the study of the state-of-the-art of instrumentation for FDP, development of mass-flow and other on-line instruments for FDP, process control analysis for FDP, and organization of a symposium on instrumentation and control for FDP. A Solids/Gas Flow Test Facility (S/GFTF) under construction for instrument development, testing, evaluation, and calibration is described. The development work for several mass-flow and other on-line instruments is described: acoustic flowmeter, capacitive density flowmeter, neutron activation flowmeter, gamma ray correlation flowmeter, optical flowmeter, composition analysis system, and capacitive liquid interface level meter.

  18. Waste Isolation Safety Assessment Program. Technical progress report for FY-1978

    Energy Technology Data Exchange (ETDEWEB)

    Brandstetter, A.; Harwell, M.A.; Howes, B.W.; Benson, G.L.; Bradley, D.J.; Raymond, J.R.; Serne, R.J.; Schilling, A.H.

    1979-07-01

    Associated with commercial nuclear power production in the United States is the generation of potentially hazardous radioactive wastes. The Department of Energy (DOE) is seeking to develop nuclear waste isolation systems in geologic formations that will preclude contact with the biosphere of waste radionuclides in concentrations which are sufficient to cause deleterious impact on humans or their environments. Comprehensive analyses of specific isolation systems are needed to assess the expectations of meeting that objective. The Waste Isolation Safety Assessment Program (WISAP) has been established at the Pacific Northwest Laboratory (operated by Battelle Memorial Institute) for developing the capability of making those analyses. Progress on the following tasks is reported: release scenario analysis, waste form release rate analysis, release consequence analysis, sorption-desorption analysis, and societal acceptance analysis. (DC)

  19. Simultaneous high-temperature removal of alkali and particulates in a pressurized gasification system. Final technical progress report, April 1981-July 1983

    Energy Technology Data Exchange (ETDEWEB)

    Mulik, P.R.; Alvin, M.A.; Bachovchin, D.M.

    1983-09-01

    This program is directed at performing experimental and analytical investigations, deriving system designs, and estimating costs to ascertain the feasibility of using aluminosilicate-based getters for controlling alkali in pressurized gasification systems. Its overall objective is to develop a plan for evaluating a scaled-up version of the gettering process as a unit operation or as an integral part of a particulate removal device. This report describes work completed on the four technical program tasks: Thermodynamic projections; Getter Selection and Qualification; System Performance Projections; and Program Definition for Concept Scale-up during the 27-month contract performance period. Work completed on the thermodynamic projections includes a data base update, development of alkali phase diagrams, and system performance projections. Getter selection and qualification efforts involved over 70 kinetic studies in which a leading candidate getter - emathlite - was selected and characterized. System performance projections identified a packed-bed configuration containing relatively large getter pellets as the preferred contacting device for a full-scale unit. For emathlite, we concluded that full-scale unit bed heights of 2 m or less would be required if we assume annual replacement on the basis of bed saturation capacity. Concept scale-up work involved defining the hardware and test program requirements for further development of the emathlite packed-bed system. 56 references, 80 figures, 74 tables.

  20. Innovative Clean Coal Technology (ICCT). Technical progress report, first quarter, 1993, January 1993--March 1993

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from U.S., Japanese and European catalyst suppliers on a high-sulfur U.S. coal-fired boiler. SCR is a post-combustion nitrogen oxide (NOx) control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NOx to convert it to nitrogen and water vapor. Although SCR is widely practiced in Japan and Europe on gas-, oil-, and low-sulfur coal-fired boilers, there are several technical uncertainties associated with applying SCR to U.S. coals. These uncertainties include: (1) potential catalyst deactivation due to poisoning by trace metal species present in U.S. coals that are not present in other fuels; (2) performance of the technology and effects on the balance-of-plant equipment in the presence of high amounts of SO{sub 2} and SO{sub 3}; and (3) performance of a wide variety of SCR catalyst compositions, geometries and methods of manufacture under typical high-sulfur coal-fired utility operating conditions. These uncertainties will be explored by constructing a series of small-scale SCR reactors and simultaneously exposing different SCR catalysts to flue gas derived from the combustion of high sulfur U.S. coal. The demonstration will be performed at Gulf Power Company`s Plant Crist Unit No. 5 (75 NM capacity) near Pensacola, Florida. The project will be funded by the U.S. Department of Energy (DOE), Southern Company Services, Inc. (SCS on behalf of the entire Southern electric system), the Electric Power Research Institute (EPRI), and Ontario Hydro. SCS is the participant responsible for managing all aspects of this project.

  1. Optimal design and routing of power lines; ecological, technical and economic perspectives (OPTIPOL). Progress report 2009

    Energy Technology Data Exchange (ETDEWEB)

    Bevanger, K.; Bartzke, G.; Broeseth, H.; Gjershaug, J.O.; Hanssen, F.; Jacobsen, K.-O.; Kvaloey, P.; May, R.; Nygaard, T.; Pedersen, H.C.; Reitan, O.; Refsnaes, S.; Stokke, S.; Vang, R.

    2009-12-15

    From 2009 inclusive, NINA has received economic support for research on power lines and wildlife from the Norwegian Research Council (NFR) through the RENERGI Programme. The project is named 'Optimal design and routing of power lines; ecological, technical and economic perspectives' (OPTIPOL). It is scheduled for 5 years (2009-1013) and is part of the activities within CEDREN, i.e. the Centre for environmental design of renewable energy (cf. http://www.cedren.no). With a grid close to 200 000 km overhead power-lines, the associated rights-of-way (ROW) affect huge land areas in Norway. The overall goal is to develop predict-ing tools for optimal routing of power lines from an environmental perspective and assess technical and economic solutions to minimize conflicts with wildlife and habitat conservation. Thus, the OPTIPOL rationale is based on the belief that the negative effects of electricity transmission and distribution can be reduced with respect to birds and mammals. OPTIPOL has several ambitious objectives, and is divided into sub-projects and specific tasks. From the first of November a PhD-student became part of the project, a position that will be held for 4 years. The main objective of the PhD-activities will be to assess how and why different wildlife species use deforested areas below power lines, evaluate possible positive and negative effects of power-line ROWs, and assess the possibilities for quality improvement. Another part of the project is dedicated the effects of linear structures on movement patterns and distribution in the landscape in native deer species. Here we will examine how different spatial scales influence the processes that guide movement patterns, and responses to linear structures. Another focus will be small game species, with mountain hare, capercaillie, black grouse and hazel grouse as model species. The main objective will be to assess the impact of transforming ROW habitats into attractive small-game foraging

  2. Supramolecular structures for photochemical energy conversion. Technical progress report, 1993--1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    This research project is concerned with the design, synthesis and study by photochemical and spectroscopic methods of complex molecular devices that mimic some important aspects of photosynthetic electron and energy transfer. Properly engineered molecules of this type can functionally mimic photosynthetic light harvesting (singlet-singlet energy transfer between chromophores), photoprotection from light-initiated singlet oxygen damage (triplet-triplet energy transfer from chlorophylls to carotenoid polyenes), and, most importantly, photoinduced multistep electron transfer to generate charge-separated states that preserve some of the photon energy as chemical potential. During the last three years, progress has been made on several fronts, all of which are related to the overall goal. A biomimetic system based on carotenoid-porphyrin-quinone triads has been constructed that demonstrates photoinduced transmembrane charge separation which in turn drives transmembrane proton transfer. Another investigation has focused on the use of proton transfer reactions to stabilize the initial products of photoinduced electron transfer and thereby increase the yield of long-lived charge separation. A third study has investigated the influence of rigid molecular geometries and short donor-acceptor separations on photoinduced electron transfer reactions. Finally, generation and quenching of singlet molecular oxygen by chlorophyll aggregates has been studied. All four studies are described and results are discussed.

  3. Advanced thermally stable jet fuels: Technical progress report, July 1994--September 1994

    Energy Technology Data Exchange (ETDEWEB)

    Schobert, H.H.; Eser, S.; Song, C.; Hatcher, P.G.; Boehman, A.; Coleman, M.M.

    1994-07-01

    There are five tasks within this project on thermally stable coal-based jet fuels. Progress on each of the tasks is described. Task 1, Investigation of the quantitative degradation chemistry of fuels, has 3 subtasks which are described: Pyrolysis of n-alkylbenzenes; Thermal decomposition of n-tetradecane in near-critical region; and Re-examining the effects of reactant and inert gas pressure on tetradecane pyrolysis--Effect of cold volume in batch reactor. Under Task 2, Investigation of incipient deposition, the subtask reported is Uncertainty analysis on growth and deposition of particles during heating of coal-derived aviation gas turbine fuels; under Task 3, Investigation of the quantitative degradation chemistry of fuels, is subtask, Effects of high surface area activated carbon and decalin on thermal degradation of jet A-1 fuel and n-dodecane; under Task 4, Coal-based fuel stabilization studies, is subtask, Screening potential jet fuel stabilizers using the model compound dodecane; and under Task 5, Exploratory studies on the direct conversion of coal to high quality jet fuels, is subtask, Shape-selective naphthalene hydrogenation for production of thermally stable jet fuels. 25 refs., 64 figs., 22 tabs.

  4. Dissolved organic matter and lake metabolism. Technical progress report, 1 July 1977--30 June 1978

    Energy Technology Data Exchange (ETDEWEB)

    Wetzel, R.G.

    1978-01-01

    Interactions of dissolved organic matter with inorganic nutrient cycling and regulation of the photosynthetic and decompositional metabolism of micro- and macroflora remains the focal point of these studies. Major efforts are directed towards the sources, fates, pathways, and interactions of dissolved organic matter in inorganic chemical cycling; allochthonous sources, metabolism en route, and inputs to the lake systems of increasing stages of eutrophication; and the relationships of these compounds to the nutrient physiology and metabolism of phytoplankton, sessile algae, macrophytes, and bacterial populations of the littoral zones and wetlands of the drainage basin. Analyses of regulatory mechanisms of growth and rates of carbon cycling center on evaluation of quantitative control interactions among the microflora of the pelagial zones of seversal lakes of progressively greater eutrophy, littoral photosynthetic producer-decomposer complex, and allochthonous inorganic--organic influxes and their biotic processing. The underlying thesis is that quantification of the dynamic carbon fluxes among these components and their rate control mechanisms by physical and chemical factors are fundamental to elucidation of the rate functions of lake eutrophication.

  5. Dissolved organic matter and lake metabolism. Technical progress report, 1 July 1978--30 Jun 1979

    Energy Technology Data Exchange (ETDEWEB)

    Wenzel, R.G.

    1979-01-01

    Progress is reported in continuing investigations focused on integrated studies of the qualitative and quantitative cycling and metabolism of particulate and dissolved organic carbon in lakes and their inflow sources (surface and subsurface). Emphasis is placed on the sources, fates, and interactions of dissolved and particulate organic matter in relation to: (a) inorganic chemical cycling, (b) allochthonous loading to the lake system, and (c) the coupled nutrient physiology and metabolism of phytoplankton, bacterial populations, macrophytes, and attendant sessile algal-bacterial communities. Regulatory mechanisms of growth and rates of carbon and nutrient cycling are being evaluated among the (a) inorganic-organic influxes of allochthonous sources as they are controlled by wetland-littoral communities, (b) the littoral photosynthetic producer-decomposer complex, and (c) the microflora of the pelagial zone. Quantification of carbon fluxes among these components and control mechanisms is fundamental to elucidation of the rate functions of lake eutrophication. The integrated studies addressing these multifacted objectives are summarized in three summary diagrams.

  6. Technical progress report during Phase 1 of the continuous fiber ceramic composites program

    Energy Technology Data Exchange (ETDEWEB)

    Richerson, D.W.

    1994-03-15

    United States industry has a critical need for materials that are lightweight, strong, tough, corrosion resistant and capable of performing at high temperatures; such materials will enable substantial increase in energy efficiency and reduction in emissions of pollutants. Continuous fiber ceramic composites (CFCCs) are an emerging class of materials which have the potential for the desired combination of properties to meet the industrial needs. A $10 billion annual market has been estimated for CFCC products by the year 2010, which equates to over 100,000 industrial sector jobs. The CFCC program began in the spring of 1992 as a three-phase 10-year effort to assess potential applications of CFCC materials, develop the necessary supporting technologies to design, analyze and test CFCC materials, conduct materials and process development guided by the applications assessment input, fabricate test samples and representative components to evaluate CFCC material capabilities under application conditions, and analyze scaleability and manufacturability plus demonstrate pilot-scale production engineering. DOE awarded 10 Phase I cooperative agreements to industry-lead teams plus identified generic supporting technology projects. This document highlights the broad progress and accomplishments on these contracts and support technology projects during Phase I.

  7. MHD Coal Fired Flow Facility. Quarterly technical progress report, July-September 1980

    Energy Technology Data Exchange (ETDEWEB)

    Altstatt, M. C.; Attig, R. C.; Brosnan, D. A.

    1980-11-01

    Significant activity, task status, planned research, testing, development, and conclusions for the Magnetohydrodynamics (MHD) Coal-Fired Flow Facility (CFFF) and the Energy Conversion Facility (ECF) are described. On Task 1, the first phase of the downstream quench system was completed. On Task 2, all three combustor sections were completed, hydrotested, ASME code stamped, and delivered to UTSI. The nozzle was also delivered. Fabrication of support stands and cooling water manifolds for the combustor and vitiation heater were completed, heat transfer and thermal stress analysis, along with design development, were conducted on the generator and radiant furnace and secondary combustor installation progressed as planned. Under Task 3 an Elemental Analyzer and Atomic Absorption Spectrophotometer/Graphite Furnace were received and installed, sites were prepared for two air monitoring stations, phytoplankton analysis began, and foliage and soil sampling was conducted using all study plots. Some 288 soil samples were combined to make 72 samples which were analyzed. Also, approval was granted to dispose of MHD flyash and slag at the Franklin County landfill. Task 4 effort consisted of completing all component test plans, and establishing the capability of displaying experimental data in graphical format. Under Task 7, a preliminary testing program for critical monitoring of the local current and voltage non-uniformities in the generator electrodes was outlined, electrode metal wear characteristics were documented, boron nitride/refrasil composite interelectrode sealing was improved, and several refractories for downstream MHD applications were evaluated with promising results.

  8. Critical contributions in MHD power generation. Quarterly technical progress report, June 1--August 31, 1977

    Energy Technology Data Exchange (ETDEWEB)

    Louis, J.F.

    1977-10-01

    Current research and development in open-cycle coal-fired MHD power generation at Massachusetts Institute of Technology is presented. Progress is reported on the following tasks: (1) Establish chemical, thermal, and electrical data to guide materials selection, develop improved detail designs, and support performance analyses of MHD electrode modules and insulator materials; (2) Parametrically investigate selected electrode properties of critical design importance in chemical, thermal, and electrical environments simulating a coal-fired MHD generator; (3) Develop combustion data pertinent to the design of MHD combustors; this work is intended to determine the combustion characteristics of selected coal feed stock in terms of devolatilization kinetics, char characteristics, and combustion gas chemistry; (4) Establish techniques for the analysis and understanding of critical MHD phenomena which have an important bearing on MHD generator performance; such phenomena include inter-electrode breakdown, time-dependent behavior, effective plasma properties and plasma inhomogeneities; (5) Establish the operating characteristics of an MHD disk generator; (6) Continue work on computer techniques for modeling and for design and cost analysis of MHD components and the overall system; (7) Integrate the engineering data and design criteria, as applicable, which are developed in the above-listed tasks into a model of the MHD channel.

  9. Critical contributions in MHD power generation. Quarterly technical progress report, June 1--August 31, 1976

    Energy Technology Data Exchange (ETDEWEB)

    Louis, J.F.

    1976-10-01

    Research progress on open-cycle coal-fired MHD power generation at Massachusetts Institute of Technology is detailed. Work is reported in the following areas: (1) Establish chemical, thermal, and electrical data to guide materials selection, develop improved detail designs, and support performance analyses of MHD electrode modules and insulator materials; (2) parametrically investigate selected electrode properties of critical design importance in chemical, thermal, and electrical environments simulating a coal-fired MHD generator; (3) develop combustion data pertinent to the design of MHD combustors; (4) establish techniques for the analysis and understanding of critical MHD phenomena which have an important bearing on MHD generator performance; (5) establish the operating characteristics of an MHD disk generator; (6) continue work on computer techniques for modeling and for design and cost analysis of MHD components and the overall system; (7) integrate the engineering data and design criteria, as applicable, which are developed in the above-listed tasks into a model of the MHD channel; (8) U-25 electrode screening tests.

  10. Great Basin paleoenvironmental studies project; Technical progress report, second quarter, September--November, 1993

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    Progress is described in the four tasks associated with this project. Task 1, Paleobotanical studies in the Great Basin, has as its objective the reconstruction of the response of vegetation to climate in order to identify periods of mesic climate at Yucca Mountain during the last 20,000 to 50,000 years. Past extremes in infiltration rates are expected to serve as estimates of climate that may be expected during the next 10,000 years at Yucca Mtn. Task 2, Paleofaunas, will construct a history of Great Basin vertebrates that will provide empirical evidence of past environmental and climatic conditions. The objective of Task 3, Geomorphology, is to document the responses of surficial processes and landforms to the climatic changes documented by studies of packrat middens, pollen, and faunal distributions. The goal of Task 4, Transportation, is to compare the results from three models that have been suggested as appropriate for evaluating flood flows on alluvial fans with the results obtained from the traditional one-dimensional, stochastic model used in previous research for Yucca Mountain. This research looked at three alluvial fans with rail transportation alignments crossing them.

  11. Capillary electrokinetic separations with optical detection. Technical progress report, February 1, 1993--January 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Sepaniak, M.J.

    1993-10-01

    This program seeks the development of capillary electrokinetic separation techniques and associated optical methods of detection. Fundamental studies of pertinent separation and band broadening mechanisms are being conducted, with the emphasis on understanding systems that include highly-ordered assemblies as running buffer additives. The additives include cyclodextrins, affinity reagents, and soluble (entangled) polymers and are employed with capillary electrophoresis, CE and/or micellar electrokinetic capillary chromatography, MECC modes of separation. The utility of molecular modeling techniques for predicting the effects of highly ordered assemblies on the retention behavior of isomeric compounds is under investigation. The feasibility of performing separations using a non-aqueous solvent/fullerene electrochromatographic system is being explored. The analytical methodologies associated with these capillary separation techniques are being advanced through the development of retention programming instumentation/techniques and new strategies for performing optical detection. The advantages of laser fluorimetry are extended through the inclusion of fluorogenic, reagents in the running buffer. These reagents include oligonucleotide intercalation reagents for detecting DNA fragments. Chemiluminescence detection using post-capillary reactors/flow cells is also in progress. Successful development of these separation and detection systems will fill current voids in the capabilities of capillary separation techniques.

  12. Advanced converter technology. Technical progress report, May 23, 1979-May 22, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Banic, C. V.; Eckhouse, S. A.; Kornbrust, F. J.; Lipman, K.; Peterson, J. L.; Rosati, R. W.

    1980-01-01

    The overall objective of this program is to define an advanced converter system employing 1980's technology in all subsystem and component areas for use in electrochemical energy storage systems. Additional experimental effort will validate elements of the advanced commutation circuitry on a full-scale breadboard basis. Improved models of battery electrical characteristics are beng defined and experimental apparatus is being designed to measure these characteristics and to enable better definition of the battery-power conditioner interface. Improvement of energy-storage system performance through modification of battery converter characteristics will also be investigated. During this first year of the contract, a new more advanced concept for power conditioning based on a concept defined by United Technologies Corporation for fuel cell use was evaluated. This high switching frequency concept has the potential for significantly reducing the size and cost of battery plant power conditioners. As a result, the Department of Energy authorized redirection of the program to first evaluate this new concept and then to reorient the program to adopt this concept as the primary one. Progress is reported. (WHK)

  13. Solvent refined coal (SRC) process. Quarterly technical progress report, January 1980-March 1980. [In process streams

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    This report summarizes the progress of the Solvent Refined Coal (SRC) project at the SRC Pilot Plant in Fort Lewis, Wahsington, and the Process Development Unit (P-99) in Harmarville, Pennsylvania. After the remaining runs of the slurry preheater survey test program were completed January 14, the Fort Lewis Pilot Plant was shut down to inspect Slurry Preheater B and to insulate the coil for future testing at higher rates of heat flux. Radiographic inspection of the coil showed that the welds at the pressure taps and the immersion thermowells did not meet design specifications. Slurry Preheater A was used during the first 12 days of February while weld repairs and modifications to Slurry Preheater B were completed. Two attempts to complete a material balance run on Powhatan No. 6 Mine coal were attempted but neither was successful. Slurry Preheater B was in service the remainder of the quarter. The start of a series of runs at higher heat flux was delayed because of plugging in both the slurry and the hydrogen flow metering systems. Three baseline runs and three slurry runs of the high heat flux program were completed before the plant was shut down March 12 for repair of the Inert Gas Unit. Attempts to complete a fourth slurry run at high heat flux were unsuccessful because of problems with the coal feed handling and the vortex mix systems. Process Development Unit (P-99) completed three of the four runs designed to study the effect of dissolver L/D ratio. The fourth was under way at the end of the period. SRC yield correlations have been developed that include coal properties as independent variables. A preliminary ranking of coals according to their reactivity in PDU P-99 has been made. Techniques for studying coking phenomenona are now in place.

  14. Advanced thermally stable jet fuels: Technical progress report, October 1994--December 1994

    Energy Technology Data Exchange (ETDEWEB)

    Schobert, H.H.; Eser, S.; Song, C.; Hatcher, P.G.; Boehman, A.; Coleman, M.M.

    1995-02-01

    There are five tasks within this project on thermally stable coal-based jet fuels. Progress on each of the tasks is described. Task 1, Investigation of the quantitative degradation chemistry of fuels, has 5 subtasks which are described: Literature review on thermal stability of jet fuels; Pyrolytic and catalytic reactions of potential endothermic fuels: cis- and trans-decalin; Use of site specific {sup 13}C-labeling to examine the thermal stressing of 1-phenylhexane: A case study for the determination of reaction kinetics in complex fuel mixtures versus model compound studies; Estimation of critical temperatures of jet fuels; and Surface effects on deposit formation in a flow reactor system. Under Task 2, Investigation of incipient deposition, the subtask reported is Uncertainty analysis on growth and deposition of particles during heating of coal-derived aviation gas turbine fuels; under Task 3, Characterization of solid gums, sediments, and carbonaceous deposits, is subtask, Studies of surface chemistry of PX-21 activated carbon during thermal degradation of jet A-1 fuel and n-dodecane; under Task 4, Coal-based fuel stabilization studies, is subtask, Exploratory screening and development potential of jet fuel thermal stabilizers over 400 C; and under Task 5, Exploratory studies on the direct conversion of coal to high quality jet fuels, are 4 subtasks: Novel approaches to low-severity coal liquefaction and coal/resid co-processing using water and dispersed catalysts; Shape-selective naphthalene hydrogenation for production of thermally stable jet fuels; Design of a batch mode and a continuous mode three-phase reactor system for the liquefaction of coal and upgrading of coal liquids; and Exploratory studies on coal liquids upgrading using mesopores molecular sieve catalysts. 136 refs., 69 figs., 24 tabs.

  15. Nuclear Physics Laboratory, University of Colorado technical progress report, 1976 and proposal for continuation of contract

    Energy Technology Data Exchange (ETDEWEB)

    1976-11-01

    This report summarizes the work carried out at the Nuclear Physics Laboratory of the University of Colorado during the period November 1, 1975 to November 1, 1976. The low energy nuclear physics section is dominated by light-ion reaction studies which span a wide range. These include both two-neutron and two-proton transfer reactions, charge exchange and inelastic scattering, as well as single nucleon transfer reactions. The nuclei studied vary widely in their mass and characteristics. These reaction studies have been aided by the multi-use scattering chamber which now allows the energy-loss-spectrometer beam preparation system (beam swinger) to shift from charged particle studies to neutron time-of-flight studies with a minimum loss of time. The intermediate energy section reflects the increase in activity accompanying the arrival of LAMPF data and the initiation of (p,d) studies at the Indiana separated-sector cyclotron. The nucleon removal results provided by the ..pi.. beam at EPICS previous to completion of the spectrometer have shown that nuclear effects dominate this process, so that the widely used free interaction picture is inadequate. The section entitled ''Other Activities'' reveals continuing activities in new applications of nuclear techniques to problems in medicine and biology. Reactions important to astrophysics continue to be investigated and our trace-element program remains at a high level of activity. The theoretical section reports new progress in understanding magnitudes of two-step reactions by inclusion of finite-range effects. A new finite-range program which is fast and economical has been completed. Intermediate energy results include calculations of ..pi..-..gamma.. angular correlations, low energy ..pi..-nucleus interactions, as well as (p,d) and nucleon scattering calculations for intermediate energies.

  16. Directional backlight liquid crystal autostereoscopic display: technical challenges, research progress, and prospect (Conference Presentation)

    Science.gov (United States)

    Fan, Hang; Li, Kunyang; Zhou, Yangui; Liang, Haowen; Wang, Jiahui; Zhou, Jianying

    2016-09-01

    Recent upsurge on virtual and augmented realities (VR and AR) has re-ignited the interest to the immerse display technology. The VR/AR technology based on stereoscopic display is believed in its early stage as glasses-free, or autostereoscopic display, will be ultimately adopted for the viewing convenience, visual comfort and for the multi-viewer purposes. On the other hand, autostereoscopic display has not yet received positive market response for the past years neither with stereoscopic displays using shutter or polarized glasses. We shall present the analysis on the real-world applications, rigid user demand, the drawbacks to the existing barrier- and lenticular lens-based LCD autostereoscopy. We shall emphasize the emerging autostereoscopic display, and notably on directional backlight LCD technology using a hybrid spatial- and temporal-control scenario. We report the numerical simulation of a display system using Monte-Carlo ray-tracing method with the human retina as the real image receiver. The system performance is optimized using newly developed figure of merit for system design. The reduced crosstalk in an autostereoscopic system, the enhanced display quality, including the high resolution received by the retina, the display homogeneity without Moiré- and defect-pattern, will be highlighted. Recent research progress including a novel scheme for diffraction-free backlight illumination, the expanded viewing zone for autostereoscopic display, and the novel Fresnel lens array to achieve a near perfect display in 2D/3D mode will be introduced. The experimental demonstration will be presented to the autostereoscopic display with the highest resolution, low crosstalk, Moiré- and defect- pattern free.

  17. Technical Progress Report on Single Pass Flow Through Tests of Ceramic Waste Forms for Plutonium Immobilization

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, P; Roberts, S; Bourcier, W

    2000-12-01

    This report updates work on measurements of the dissolution rates of single-phase and multi-phase ceramic waste forms in flow-through reactors at Lawrence Livermore National Laboratory. Previous results were reported in Bourcier (1999). Two types of tests are in progress: (1) tests of baseline pyrochlore-based multiphase ceramics; and (2) tests of single-phase pyrochlore, zirconolite, and brannerite (the three phases that will contain most of the actinides). Tests of the multi-phase material are all being run at 25 C. The single-phase tests are being run at 25, 50, and 75 C. All tests are being performed at ambient pressure. The as-made bulk compositions of the ceramics are given in Table 1. The single pass flow-through test procedure [Knauss, 1986 No.140] allows the powdered ceramic to react with pH buffer solutions traveling upward vertically through the powder. Gentle rocking during the course of the experiment keeps the powder suspended and avoids clumping, and allows the system to behave as a continuously stirred reactor. For each test, a cell is loaded with approximately one gram of the appropriate size fraction of powdered ceramic and reacted with a buffer solution of the desired pH. The buffer solution compositions are given in Table 2. All the ceramics tested were cold pressed and sintered at 1350 C in air, except brannerite, which was sintered at 1350 C in a CO/CO{sub 2} gas mixture. They were then crushed, sieved, rinsed repeatedly in alcohol and distilled water, and the desired particle size fraction collected for the single pass flow-through tests (SPFT). The surface area of the ceramics measured by BET ranged from 0.1-0.35 m{sup 2}/g. The measured surface area values, average particle size, and sample weights for each ceramic test are given in the Appendices.

  18. Improved methods for water shutoff. Final technical progress report, October 1, 1997--September 30, 1998

    Energy Technology Data Exchange (ETDEWEB)

    Seright, R.S.; Liang, J.T.; Schrader, R.; Hagstrom, J. II; Liu, J.; Wavrik, K.

    1998-10-01

    In the United States, more than 20 billion barrels of salt water are produced each year during oilfield operations. A tremendous economic incentive exists to reduce water production if that can be accomplished without significantly sacrificing hydrocarbon production. This three-year research project had three objectives. The first objective was to identify chemical blocking agents that will (a) during placement, flow readily through fractures without penetrating significantly into porous rock and with screening out or developing excessive pressure gradients and (b) at a predictable and controllable time, become immobile and resistant breakdown upon exposure to moderate to high pressure gradients. The second objective was to identify schemes that optimize placement of the above blocking agents. The third objective was to explain why gels and other chemical blocking agents reduce permeability to one phase (e.g., water) more than that to another phase (e.g., oil or gas). The authors also wanted to identify conditions that maximize this phenomenon. This project consisted of three tasks, each of which addressed one of the above objectives. This report describes work performed during the third and final period of the project. During this three-year project, they: (1) Developed a procedure and software for sizing gelant treatments in hydraulically fractured production wells; (2) Developed a method (based on interwell tracer results) to determine the potential for applying gel treatments in naturally fractured reservoirs; (3) Characterized gel properties during extrusion through fractures; (4) Developed a method to predict gel placement in naturally fractured reservoirs; (5) Made progress in elucidating the mechanism for why some gels can reduce permeability to water more than that to oil; (6) Demonstrated the limitations of using water/oil ratio diagnostic plots to distinguish between channeling and coning; and (7) Proposed a philosophy for diagnosing and attacking water

  19. Aligning Mathematics Assessment Standards: New Mexico and the 2009 National Assessment of Educational Progress (NAEP). REL Technical Brief. REL 2008-No. 011

    Science.gov (United States)

    Shapley, Kathy L.; Brite, Jessica

    2008-01-01

    This technical brief examines the current alignment between the New Mexico Standards Based Assessment (NMSBA) standards and the 2009 National Assessment of Educational Progress (NAEP) mathematics framework. It looks at the extent to which current state assessment standards cover the content on which 2009 NAEP assessments will be based. Applying…

  20. Savannah River Ecology Laboratory Annual Technical Progress Report of Ecological Research, June 30, 2001

    Energy Technology Data Exchange (ETDEWEB)

    Bertsch, Paul M.; Janecek, Laura; Rosier, Brenda

    2001-06-30

    The Savannah River Ecology Laboratory (SREL) is a research unit of the University of Georgia (UGA) and has been conducting ecological research on the Savannah River Site (SRS) in South Carolina for 50 years. The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts fundamental and applied ecological research, as well as education and outreach programs, under a Cooperative Agreement with the U.S. Department of Energy (DOE) SRS near Aiken, South Carolina. The Laboratory's research mission during the 2001 fiscal year was fulfilled with the publication of one book and 83 journal articles and book chapters by faculty, technical staff, students, and visiting scientists. An additional 77 journal articles have been submitted or are in press. Other noteworthy events took place as faculty members and graduate students received awards. These are described in the section Special Accomplishments of Faculty, Staff, Students, and Administration on page 54. Notable scientific accomplishments include work conducted on contaminant transport, global reptile decline, phytoremediation, and radioecology. Dr. Domy Adriano authored the second edition of his book ''Trace Elements in Terrestrial Environments: Biogeochemistry, Bioavailability, and Risks of Metals'', which was recently published by Springer-Verlag. The book provides a comprehensive treatment of many important aspects of trace elements in the environment. The first edition of the book, published in 1986, has become a widely acclaimed and cited reference. International attention was focused on the problem of reptile species decline with the publication of an article on this topic in the journal ''Bioscience'' in August, 2000. The article's authors included Dr. Whit Gibbons and a number of other SREL herpetologists who researched the growing worldwide problem of decline of reptile species. Factors related

  1. Optimal design and routing of power lines; ecological, technical and economic perspectives (OPTIPOL). Progress report 2012

    Energy Technology Data Exchange (ETDEWEB)

    Bevanger, Kjetil; Bartzke, Gundula; Broeseth, Henrik; Dahl, Espen Lie; Gjershaug, Jan Ove; Hanssen, Frank; Jacobsen, Karl-Otto; Kleven, Oddmund; Kvaloey, Paal; May, Roel; Meaas, Roger; Nygaaard, Torgeir; Resnaes, Steinar; Stokke, Sigbjoern; Thomassen, Joern

    2012-07-01

    birds in the database, compared to only 117 a year earlier. WP5 - 'A Least Cost Path (LCP) toolbox for optimal route routing of power lines', has developed an LCP-pilot to demonstrate the LCP method, based on the impact studies were undertaken prior to construction of a 420 kV transmission line in Central Norway 2005. Relevant economic, ecological and technological environment criteria based on suggestions from interested users (NGOs, government, industry, etc.), was used. LCP-pilot and a fuzzy-logic approach of this was demonstrated in the first dialogue-based workshop, 23.-24. april 2012. The seminar, which had an emphasis on criteria definitions were followed up with a working seminar that focused criterion values ??on 20 november 2012. Lecture - 'A Least Cost Path (LCP) Toolbox for Optimal Routing of Power Lines, -was presented and submitted as contributions to the conference report from 'The 10th ROW Conference' in Arizona, 'The 32nd Annual Conference of the International Association for Impact Assessment (IAIA12) ' in Porto, Portugal, and 'The ESRI European User Conference' in Oslo. WP6 - 'Birds and camouflaging of power lines', has almost completed the final report, 'Power line camouflaging. An assessment of the ecological and technical challenges'. 'Because of the budget situation in CEDREN However, completion of the report postponed until the end of April 2013. WP7 - 'Effect of line marking / modifications remedial measures against bird mortality' has almost completed the final report 'Opportunities and limitations in terms of reducing mortality in birds due to collision and electrocution.' Due to overall budget situation in CEDREN the report deferred to the end of april 2013. WP8, 'guidelines for technological solutions that may reduce mortality in birds because of the power line's', has focused topics relating to the labeling, design, insulation, camouflage and wiring. The results, which are presented in the notes and articles, will be implemented in

  2. Modeling the impacts of climate change and technical progress on the wheat yield in inland China: An autoregressive distributed lag approach.

    Science.gov (United States)

    Zhai, Shiyan; Song, Genxin; Qin, Yaochen; Ye, Xinyue; Lee, Jay

    2017-01-01

    This study aims to evaluate the impacts of climate change and technical progress on the wheat yield per unit area from 1970 to 2014 in Henan, the largest agricultural province in China, using an autoregressive distributed lag approach. The bounded F-test for cointegration among the model variables yielded evidence of a long-run relationship among climate change, technical progress, and the wheat yield per unit area. In the long run, agricultural machinery and fertilizer use both had significantly positive impacts on the per unit area wheat yield. A 1% increase in the aggregate quantity of fertilizer use increased the wheat yield by 0.19%. Additionally, a 1% increase in machine use increased the wheat yield by 0.21%. In contrast, precipitation during the wheat growth period (from emergence to maturity, consisting of the period from last October to June) led to a decrease in the wheat yield per unit area. In the short run, the coefficient of the aggregate quantity of fertilizer used was negative. Land size had a significantly positive impact on the per unit area wheat yield in the short run. There was no significant short-run or long-run impact of temperature on the wheat yield per unit area in Henan Province. The results of our analysis suggest that climate change had a weak impact on the wheat yield, while technical progress played an important role in increasing the wheat yield per unit area. The results of this study have implications for national and local agriculture policies under climate change. To design well-targeted agriculture adaptation policies for the future and to reduce the adverse effects of climate change on the wheat yield, climate change and technical progress factors should be considered simultaneously. In addition, adaptive measures associated with technical progress should be given more attention.

  3. Use of fluidized bed combustion by-products for liners and alkali substitutes. Technical report, December 1, 1994--February 28, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Paul, B.C.; Esling, S. [Southern Illinois Univ., Carbondale, IL (United States); Pisani, F. [Illinois Abandoned Mined Lands Reclamation Council, IL (United States); Wells, T. [Archer-Daniels-Midland Co., Minneapolis, MN (United States)

    1996-03-01

    Fluidized Bed Combustion (FBC) of coal eliminates most emissions of sulfur and nitrogen oxides, but produces sizable volumes of a solid residue that EPA may require to be placed in capped and lined landfills. Fluidized Bed Combustors are one of the most promising growth markets for Illinois coal and imposing cap and liner requirements would render the technology economically inviable. Fluidized Bed residues are cement-like and when mixed with soil produce a material as impermeable as the clay liners used at landfills. This project will demonstrate that Fluidized Bed Combustion Residues can be mixed with soils by regular construction equipment and used in place of clays as a liner material. The demonstration cap will cover an area of seven acres, and will prevent water infiltration into acid producing material. Baseline studies of Briar Creek indicate that the water is now highly degraded by acid drainage. Construction delays have enhanced the data collected on Briar Creek by allowing monitoring to continue through major seasonal changes without any effects attributable to the FBC ash. The materials needed to place the wells and lysimeters as soon as the weather improves this spring have been purchased and delivered. Also experiments suggest that it may be possible to control dust by foam conditioning the FBC ash at the power station.

  4. 钛白粉生产工艺技术进展%Technical progress of titanium dioxide manufacturing processes

    Institute of Scientific and Technical Information of China (English)

    龚家竹

    2012-01-01

    简要介绍了钛白粉全球主要生产商和市场概况、原料加工工艺技术和现有的硫酸法、氯化法钛白粉生产工艺技术;也介绍了最新工艺中钛原料富集的替代金红石工艺(REPTILE)和钛铁矿焙烧磁选分离酸回收工艺(ERMS SR),以及盐酸法的(Altair)生产工艺和碱融法的绿色生产工艺等钛白粉生产工艺技术的最新进展.%Major global producers and markets of titanium dioxide were briefly reviewed.Titanium dioxide's raw material processing techniques and existing manufacturing processes,such as sulfuric acid process and chlorination process,were introduced.Latest titanium dioxide manufacturing processes,such as REPTILE and ERMS SR,as well as the technical progress in production technology of hydrochloric acid process (Altair),and in the green production technology of alkali molten process were also introduced.

  5. Fundamental characterization of alternate fuel effects in continuous combustion systems. Summary technical progress report, August 15, 1978-January 31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Blazowski, W.S.; Edelman, R.B.; Wong, E.

    1980-02-27

    The overall objective of this contract is to assist in the development of fuel-flexible combustion systems for gas turbines as well as Rankine and Stirling cycle engines. The primary emphasis of the program is on liquid hydrocarbons produced from non-petroleum resources. Fuel-flexible combustion systems will provide for more rapid transition of these alternative fuels into important future energy utilization centers (especially utility power generation with the combined cycle gas turbine). The specific technical objectives of the program are: (a) develop an improved understanding of relationships between alternative fuel properties and continuous combustion system effects, and (b) provide analytical modeling/correlation capabilities to be used as design aids for development of fuel-tolerant combustion systems. This is the second major report of the program. Key experimental findings during this reporting period concern stirred combustor soot production during operation at controlled temperature conditions, soot production as a function of combustor residence time, an improved measurement technique for total hydrocarbons and initial stirred combustor results of fuel nitrogen conversion. While the results to be presented concern a stirred combustor which utilizes premixed fuel vapor/oxidant mixtures, a new combustor which combusts liquid fuel injected into the reactor as a spray has been developed and will be described. Analytical program progress includes the development of new quasiglobal models of soot formation and assessment of needs for other submodel development.

  6. Distribution of marine birds on Georges Bank and adjacent waters. Technical progress report, 1 January--31 August 1978

    Energy Technology Data Exchange (ETDEWEB)

    Powers, K.D.

    1978-10-01

    The work accomplished during the period covered in this technical progress report demonstrates the importance, interest, and necessity of a distribution study of marine birds in the Georges Bank area on a national and international scale. Cooperation was extended by the U.S. National Marine Fisheries Service, U.S. Fish and Wildlife Service, U.S. Coast Guard, and by the Canadian Wildlife Service, Halifax, N.S., AltantNIRO, Kaliningrad, USSR, and Federal Republic of Germany. Two sampling methods, fixed-area and total bird counts, were effectively employed, which allow comparable data bases with marine bird distribution information being collected in the North Pacific, Bering and Chukchi Seas (Outer Continental Shelf Energy Assessment Program), and in the North Atlantic and Canadian Arctic (CWS and The Seabird Group). A marine bird data retrieval bank is being developed for MBO seabird data at the USFWS Migratory Bird and Habitat Research Laboratory. A food habits bibliography and prey item/bird species summary table for marine birds in the western North Atlantic has been prepared from existing literature. Unpublished NMFS data on zooplankton/ichthyoplankton, and ground fish is being made available for possible correlations in distribution of selected prey items with bird species.

  7. Developments in breeding of Agaricus bisporus var. bisporus: progress made and technical and legal hurdles to take.

    Science.gov (United States)

    Sonnenberg, Anton S M; Baars, Johan J P; Gao, Wei; Visser, Richard G F

    2017-03-01

    True breeding of button mushrooms has hardly been done in the last decades, despite this species being one of the most cultivated mushrooms worldwide. Research done in the last 20 years has identified and characterised new germplasm and improved our understanding of the genetic base for some traits. A substantial collection of wild-collected strains is now available and partly characterised for a number of important traits such as disease resistance and yield. Most of the variations found in a number of important agronomic traits have a considerable heritability and are thus useful for breeding. Genetic marker technology has also developed considerably for this mushrooms in the last decade and used to identify quantitative trait loci (QTL) for important agronomic traits. This progress has, except for one example, not resulted so far into new commercially varieties. One of the reasons lies in the typical life cycle of the button mushroom Agaricus bisporus var. bisporus which hampers breeding. Joint investment is needed to solve technical problems in breeding. Special attention is needed for the protection of new varieties. Due to its typical life cycle, it is very easy to generate so called "look-a-likes" from protected cultivars by screening fertile single spore cultures. A consensus has been reached within the mushroom (breeding) industry to consider this method as the generation of essentially derived varieties as defined in plant breeding.

  8. High octane ethers from synthesis gas-derived alcohols. Quarterly technical progress report, July--September 1993

    Energy Technology Data Exchange (ETDEWEB)

    Klier, K.; Herman, R.G.; Feeley, O.C.; Johansson, M.A.

    1993-11-01

    The objective of the proposed research is to synthesize oxygenated fuel ethers, primarily methyl isobutyl ether (MIBE) and methyl tertiary butyl ether (MTBE), directly from coal-derived H{sub 2}/CO/CO{sub 2} synthesis via alcohol mixtures that are rich in methanol and 2-methyl-1-proanol (isobutanol). The overall scheme involves gasification of coal, purification and shifting of the synthesis gas, higher alcohol synthesis, and direct synthesis of ethers. Both organic and inorganic catalysts will be investigated, and the better catalysts will be subjected to long term performance studies. The project is divided into the following three tasks: (1) synthesis of high octane ethers from alcohol mixtures containing predominantly methanol and 2-methyl-1-propanol over superacid resins, (2) inorganic catalysts for the synthesis of high octane ethers form alcohols, and (3) long term performance and reaction engineering for scale-up of the alcohols-to-ether process. A summary of technical progress is provided in this report.

  9. Micropore diffusion in coal chars under reactive conditions: Quarterly technical progress report, 15 March 1987-15 June 1987

    Energy Technology Data Exchange (ETDEWEB)

    Calo, J.M.; Perkins, M.T.; Lilly, W.D.

    1987-01-01

    In this third quarterly technical progress report, we present some initial data obtained with the ''gradientless'' reactor, and explore the effects of dispersion in the reactor sampling line. In particular: the gas sampling system and the solenoid valve network have been assembled and interfaced between the 3'' Berty catalytic reactor and the mass spectrometer beam system; initial purging experiments were conducted with this system, focusing on the convoluting effects of the sampling line on time constant measurements; it was shown and concluded that for the projected operating regime, the sampling line configuration without the in-line filter should not introduce any appreciable error in the measurements; and an analysis of the dispersion effects to be expected in the sampling line has defined the useful flow rate ranges for the current system and the means by which to extend the dynamic range; e.g., by increasing the length of the small bore diameter tubing. 21 refs., 11 figs.

  10. Progress on Technology of Coal Bed Methane Development and Utilization in China Coal Mining Area%我国煤矿区煤层气开发利用技术进展

    Institute of Scientific and Technical Information of China (English)

    宁宇

    2013-01-01

    According to rich coal bed methane resources in China and high difficult development actual conditions, the state enhanced the attention degree and the investment dynamic to the technology and innovation of the coal bed methane development. A series of breakthrough progress was made.The paper summarized the new progresses on the basic theory,key technology,heavy equipment,transportation and utilization, development mode and others in the coal bed methane development and utilization in coal mining area. The paper analyzed the problems and challenges faced to the coal bed methane development and utilization in coal mining area. The paper provided the development orientation of the coal bed methane development and utilization in coal mining area in order to provide the references to the high efficient development and utilization of the coal bed methane in coal mining area.%针对我国煤层气资源丰富但开发难度较大的实际情况,国家通过加大科技创新重视程度和投入力度,取得了一系列突破性进展,对煤矿区煤层气开发利用中的基础理论、关键技术、重大装备、集输利用、开发模式等方面取得的新进展进行了总结,同时剖析了煤矿区煤层气开发利用面临的问题,并提出了煤矿区煤层气开发利用技术的发展方向,以期为煤矿区煤层气高效开发利用提供参考.

  11. Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author, Volume 18 (1) through Volume 22 (6)

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, W.B.; Passiakos, M.

    1982-06-01

    This index to Nuclear Safety covers articles published in Nuclear Safety, Volume 18, Number 1 (January-February 1977) through Volume 22, Number 6 (November-December 1981). The index is divided into three section: a chronological list of articles (including abstracts), a permuted-title (KWIC) index, and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. Over 300 technical articles published in Nuclear Safety in the last 5 years are listed in this index.

  12. Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author. Vol. 11(1)--Vol. 18(6)

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, W.B.; Klein, A.

    1978-04-11

    This index to Nuclear Safety covers articles published in Nuclear Safety, Vol. 11, No. 1 (January-February 1970), through Vol. 18, No. 6 (November-December 1977). It is divided into three sections: a chronological list of articles (including abstracts) followed by a permuted-title (KWIC) index and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center (NSIC), covers all safety aspects of nuclear power reactors and associated facilities. Over 450 technical articles published in Nuclear Safety in the last eight years are listed in this index.

  13. Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol 11, No. 1 through Vol. 16, No. 6

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, W.B.; Klein, A.

    1976-04-01

    This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970) through Vol. 16, No. 6 (Nov.-Dec. 1975). Included in the index is a chronological list of articles (including abstract) followed by both a KWIC index and an Author Index. Nuclear Safety is a bimonthly technical progress review prepared by the Nuclear Safety Information Center and covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 300 technical articles in the last six years of publication.

  14. Fossil energy program. Progress report, July 1980

    Energy Technology Data Exchange (ETDEWEB)

    McNeese, L. E.

    1980-10-01

    This report - the seventy-second of a series - is a compendium of monthly progress reports for the ORNL research and development programs that are in support of the increased utilization of coal and other fossil fuel alternatives to oil and gas as sources of clean energy. The projects reported this month include those for coal conversion development, chemical research and development, materials technology, component development and process evaluation, technical support to major liquefaction projects, process and program analysis, fossil energy environmental analysis, coal preparation and waste utilization, coal preparation plant automation, atmospheric fluidized bed coal combustor for cogeneration, technical support to the TVA fluidized bed combustion demonstration plant program, fossil energy applications assessments, performance assurance system support for fossil energy projects, international assessment of atmospheric fluidized bed combustion technology, and PFBC systems analysis.

  15. Fossil Energy Program progress report for May 1979

    Energy Technology Data Exchange (ETDEWEB)

    1979-07-01

    This report - the fifty eighth of a series - is a compendium of monthly progress reports for the ORNL research and development programs that are in support of the increased utilization of coal and other fossil fuel alternatives to oil and gas as sources of clean energy. The projects reported this month include those for coal conversion development, materials engineering, a coal equipment test program, an atmospheric fluid bed combustor for cogeneration, engineering studies and technical support, process and program analysis, environmental assessment studies, magnetic beneficiation of dry pulverized coal, technical support to the TVA fluid bed combustion program, coal cogeneration/district heating plant assessment, and chemical research and development.

  16. Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    Paul D. Ronney

    2004-08-26

    An ignition source was constructed that is capable of producing a pulsed corona discharge for the purpose of igniting mixtures in a test chamber. The corona generator can also be used as the ignition source for one cylinder on a test engine. The first tests were performed in a cylindrical shaped chamber to study the characteristics of the corona and analyze various electrode geometries. Next a test chamber was constructed that closely represented the dimensions of the combustion chamber of the test engine at USC. Combustion tests were performed in this chamber and various electrode diameters and geometries were tested. Higher peak pressures and faster pressure rise times were realized consistently in all test chambers versus standard spark plug ignition. A test engine was purchased for the project that has two spark plug ports per cylinder to The data acquisition and control system hardware for the USC engine lab was updated with new equipment. New software was also developed to perform the engine control and data acquisition functions including cylinder pressure monitoring. A ceramic corona electrode has been designed that fits in the new test engine and is capable of withstanding the pressures and temperatures encountered inside the combustion chamber. The corona ignition system was tested on the engine and an increase in both peak pressure and IMEP were seen in the initial test. There are issues that must be addressed before on-engine testing can continue such as EMF interference from the corona generator and electrical insulation on portions of the piston and cylinder head to prevent arcing. The EMF issue can be solved with proper shielding and grounding and various ceramic coatings are being researched for electrical insulation.

  17. Final Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    J.Y. Hwang; R.C. Greenlund

    2002-12-31

    Michigan Technological University has demonstrated major inroads in establishing the viability of utilizing aluminum smelting by-product waste materials in lightweight concrete product applications. The research identified key elements of producing various forms of lightweight concrete products through utilizing various procedures and mixture components with the by-product materials. A process was developed through pilot plant testing that results in additional aluminum recovery at finer sizes, a clean returnable salt product through spray drying technology, and a low-salt-content oxide product with enough aluminum metal content that it can be used to form lightweight cementitious mixtures. Having three distinct products aids in generating favorable process economics. Revenue projections from aluminum recovery and salt recovery are enough to cover processing costs and create a cost-free oxide product to market for lightweight concrete applications. This supply side commercialization strategy offers aluminum by-product recyclers a potentially no cost product, which has been demonstrated through this project to create desirable and marketable lightweight concrete products of various forms. Environmental benefits to the public are tremendous. At best, all dross and salt cake materials have the potential to be completely recycled and utilized. At worst, disposal sites would see a reduced amount of material: a post processed oxide product with little salt and no hydrogen sulfide or ammonia gas generating capability, which, if isolated from high alkali conditions, would pose no reactivity concerns. The US aluminum industry has historically, along with the steel industry, been a leader in recycling metal. The findings from this project, increased metal recovery, improved salt recycling, and demonstrated end uses for oxide residues, will go a long way in helping the aluminum industry obtain 100% material utilization and zero discharge.

  18. Progress of purification technology for low concentration coal-bed methane%低浓度煤层气分离提纯的研究进展

    Institute of Scientific and Technical Information of China (English)

    吕秋楠; 李小森; 徐纯刚; 陈朝阳; 李刚

    2013-01-01

    This paper reviewed the methods of methane (CH4) separation and purification from coal-bed methane (CBM),including low-temperature distillation,adsorption,membrane separation and gas hydrate separation. By the analysis of the advantages and the disadvantages of these methods,the separation efficiencies under different technical conditions were compared and discussed. Key issues needed to be solved for each method were summarized. For the low-temperature distillation method,de-oxidation is necessarily conducted for the oxygen-containing CBM. The selection of the adsorbent is the key for the adsorption method because the adsorbent determines the economy benefit directly. As for the membrane separation,the separation is affected by the selection of the membrane materials and membrane-making technology. For the hydrated-based CH4 separation,a good additive is crucial to promote the hydrate formation and enhance the CH4 separation efficiency. Finally,the separation of multi-methods or the separation by multi-stage processes is proposed for the future development of CBM separation.%  综述了应用于低浓度煤层气分离的主要方法,包括低温精馏法、吸附分离法、膜分离法和水合物法,探讨了各种方法在不同工艺条件下的分离效果,分析了它们的优缺点。文中总结了每种方法需要解决与突破的关键性问题:低温精馏法获得的甲烷浓度高,但在处理含氧煤层气时首先要脱氧;吸附分离的关键技术在于吸附剂的选择,吸附剂决定了该方法的经济效益与难易程度;对于膜法分离,影响煤层气分离效果的主要因素在于膜材料的选择及制膜工艺;对于水合物法,寻找制备具有较高分离效率的添加剂是关键。最后指出,多种方法结合、多级分离的分离方法是未来研究发展方向。

  19. Healy clean coal project. Quarterly technical progress report No. 16-19, October 1, 1994--September 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    This Quarterly Technical Progress Report is required under U.S. Department of Energy (DOE) Cooperative Agreement, Section XV, {open_quotes}Reporting Requirements{close_quotes} and Attachment C, {open_quotes}Federal Assistance Reporting Checklist{close_quotes}. It covers the period of October 1, 1994 through September 30, 1995. The primary objective of the HCCP is to conduct a cost-sharing project that will demonstrate a new power plant design which features innovative integration of an advanced combustor and heat recovery system coupled with both high and low temperature emission control processes. The parties anticipate that if the demonstration project is successful, the technology could become commercialized in the near term and will be capable of (1) achieving significant reductions in the emissions of sulfur dioxide and the oxides of nitrogen from existing facilities to minimize environmental impacts such as transboundary and interstate pollution and/or (2) providing for future energy needs in an environmentally acceptable manner. The primary equipment elements comprising this new power plant design includes entrained combustion systems coupled with a boiler which will produce low NOx levels, function as a limestone calciner and first stage SO{sub 2} remover in addition to its heat recovery function; a single spray dryer absorber vessel for second stage sulfur removal; a baghouse for third stage sulfur and particulate removal; and a lime activation system which recovers unused reagent from particulate collected in the baghouse. The emission levels Of SO{sub 2}, NOx, and particulate to be demonstrated are expected to be better than the federal New Source Performance Standards (NSPS).

  20. Micropore diffusion in coal chars under reactive conditions: Quarterly technical progress report, 15 September 1986-15 December 1986

    Energy Technology Data Exchange (ETDEWEB)

    Calo, J.M.

    1986-01-01

    This project is concerned with the development of a new technique for measuring the rates of diffusion of gases on the microporous structure of coal chars. Mass transport in pores of molecular dimensions is known to be an activated, relatively slow process. The gasification of coal chars may be transport-limited. To correlate and predict gasification reactivity, it is quite important to know over what range of conditions such limitations may control. The initial transient behavior of a gaseous species exposed to such chars primarily reflects the transport resistance offered by the micropores. When this process is conducted using a well-defined perturbation in a mixed reactor, the diffusion step can often be separated from the subsequent reaction steps, so that measurements can be conducted under actual gasification conditions. We will apply this technique to a few well-characterized coal/carbon chars. Micropore diffusion times in these samples will be determined for various gaseous species relevant to the gasification environments. The primary variables will be temperature and degree of conversion (i.e., burn-off). Measurements will be examined with respect to changes occurring in the pore structure of the chars. In this first quarterly technical progress report, the background and objectives of the study and the requisite experimental preparations to begin the micropore diffusion studies are presented. In particular, during the reporting period: the graduate assistant on this project conducted a literature review of the general area of micropore diffusion and began to acquire the necessary background for the experimental study; the inception of a pore model was undertaken involving micropore diffusion; and the Autoclave Engineers 3'' Berty catalytic reactor has been refurbished and modified for the study. 59 refs., 2 figs.

  1. Botanical inventory of the Rocky Flats AEC site: mapping methods and preliminary maps. Technical progress report, July 31, 1975--April 28, 1976

    Energy Technology Data Exchange (ETDEWEB)

    Webber, P.J.; Clark, S.V.

    1976-01-01

    This Technical Progress Report represents a small but important part of the overall progress and research effort of this contract. It outlines the methods used to produce one 1:12,000 colored vegetation map of the Rocky Flats site and its surrounding area and six black and white 1:500 vegetation maps of intensively studied experimental plots. These maps are already being used by various researchers and it is appropriate that the mapping methods be detailed prior to the final contract report so that their use may be optimised. (auth)

  2. GPHS-RTGs in support of the Cassini Mission. Semi annual technical progress report, 1 April 1996--29 September 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-20

    This technical progress report discusses work on the Radioisotope Generators and Ancillary Activities for the Cassini spacecraft. The Cassini spacecraft is expected to launch in October 1997, and will explore Saturn and its moons. This progress report discusses issues in: spacecraft integration and liason, engineering support, safety, qualified unicouple fabrication, ETG fabrication and testing, ground support equipment, RTG shipping and launch support, designs, reviews and mission application. Safety analysis of the RTGs during reentry and launch accidents are covered. This report covers the period of April 1 to September 29, 1996.

  3. Technical efficiency and productivity of Chinese county hospitals: an exploratory study in Henan province, China.

    Science.gov (United States)

    Cheng, Zhaohui; Tao, Hongbing; Cai, Miao; Lin, Haifeng; Lin, Xiaojun; Shu, Qin; Zhang, Ru-Ning

    2015-09-09

    Chinese county hospitals have been excessively enlarging their scale during the healthcare reform since 2009. The purpose of this paper is to examine the technical efficiency and productivity of county hospitals during the reform process, and to determine whether, and how, efficiency is affected by various factors. 114 sample county hospitals were selected from Henan province, China, from 2010 to 2012. Data envelopment analysis was employed to estimate the technical and scale efficiency of sample hospitals. The Malmquist index was used to calculate productivity changes over time. Tobit regression was used to regress against 4 environmental factors and 5 institutional factors that affected the technical efficiency. (1) 112 (98.2%), 112 (98.2%) and 104 (91.2%) of the 114 sample hospitals ran inefficiently in 2010, 2011 and 2012, with average technical efficiency of 0.697, 0.748 and 0.790, respectively. (2) On average, during 2010-2012, productivity of sample county hospitals increased by 7.8%, which was produced by the progress in technical efficiency changes and technological changes of 0.9% and 6.8%, respectively. (3) Tobit regression analysis indicated that government subsidy, hospital size with above 618 beds and average length of stay assumed a negative sign with technical efficiency; bed occupancy rate, ratio of beds to nurses and ratio of nurses to physicians assumed a positive sign with technical efficiency. There was considerable space for technical efficiency improvement in Henan county hospitals. During 2010-2012, sample hospitals experienced productivity progress; however, the adverse change in pure technical efficiency should be emphasised. Moreover, according to the Tobit results, policy interventions that strictly supervise hospital bed scale, shorten the average length of stay and coordinate the proportion among physicians, nurses and beds, would benefit hospital efficiency. Published by the BMJ Publishing Group Limited. For permission to use (where

  4. 新世纪不饱和聚酯树脂纵横谈%TECHNICAL PROGRESS OF UNSATURATED POLYESTER RESIN AT HOME AND ABROAD IN THE NEW CENTURY

    Institute of Scientific and Technical Information of China (English)

    蔡永源; 于同福

    2001-01-01

    从国内外不同视角和纵横面,阐述目前国内外不饱和聚酯树脂(UPR)高分子材料发展概况、用途分配、加工及技术进展。%The production capacity,processing technology application and technical progress of unsaturated polyester resins at home and abroad in the new century were discribed in this paper.

  5. Active sites in char gasification. Quarterly technical progress report, 1 January 1984-31 March 1984. [Polymers of phenol-formaldehyde family; chars produced from model compounds

    Energy Technology Data Exchange (ETDEWEB)

    Calo, J.M.; Suubers, E.M.; Wojtowicz, M.; Lilly, W.

    1984-05-01

    This project is concerned with the study of the nature and behavior of active sites in gasification of chars produced from synthesized model compounds, primarily of the phenol-formaldehyde family of resins. The current technical progress report presents further developments on resin synthesis and characterization and the design of a pyro-gasifier reactor for transient kinetic studies of the chars produced from the model compounds. 7 references, 12 figures, 2 tables.

  6. Technical notes for the conceptual design for an atmospheric fluidized-bed direct combustion power generating plant. [Comparison of AFB plant and pulverized coal plant

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-04-01

    The first part of this report presents a comparison of the conceptual designs of a large (570 MW(e)) pulverized coal (PC) steam generator equipped with a wet limestone flue gas desulfurization (FGD) system and two equivalent sized atmospheric fluidized bed (AFB) steam generators including balance of plants for electric-power generation. The reader is cautioned that this portion of the report compares a zero generation AFB technology to pulverized coal technology which has been operationally and economically optimized for the past half-century. This comparison is intended to be indicative of whether further development of the AFB concept as a viable alternative to the PC/FGD concept for electric-power generation is merited. In the second part, the load-following capability of a once-through subcritical atmospheric fluidized bed boiler is analyzed. Digital computer simulation predictions of the plant's response to open loop step changes in firing rate, feedwater flow, governor valve, unit load demand, etc, are made. The predicted response of throttle pressure, steam temperature, unit load, etc, are compared to the response of a conventional coal-fired, once-through, subcritical unit. The load-following capability is assessed through this qualitative comparison. Additional model response predictions are also presented for which no test data are presently available.

  7. Design, construction, operation and evaluation of a prototype culm combustion boiler/heater unit. Technical progress report, October 1-December 31, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-02-01

    This report provides a summary of the work performed on the Prototype Culm Combustion Boiler/Heater Unit, Phase I - Engineering Design and Analysis and Limited Phase II - Prototype Plant Construction during the period October 1, 1979 through December 31, 1979. The objectives of the program as well as the technical progress and problem areas encountered are presented. Progress on the components and system engineering studies is described. The Preliminary Design of Prototype Unit Topical Report was submitted. Final design activity is continuing and the progress on drawing preparation and advanced procurement activity is discussed. Based on authorization for a limited amount of Phase II activity, initial Purchase Orders were released authorizing preparation of certified drawings for fabricated equipment required to support the Phase I final design activity. The Purchase Order for site clearance and installation of boiler foundations was awarded and ground breaking ceremonies were held at the Prototype Culm Combustion Boiler site in Paxinos, Pennsylvania, on December 7, 1979.

  8. Thermal energy storage systems using fluidized bed heat exchangers

    Science.gov (United States)

    Ramanathan, V.; Weast, T. E.; Ananth, K. P.

    1980-01-01

    The viability of using fluidized bed heat exchangers (FBHX) for thermal energy storage (TES) in applications with potential for waste heat recovery was investigated. Of the candidate applications screened, cement plant rotary kilns and steel plant electric arc furnaces were identified, via the chosen selection criteria, as having the best potential for successful use of FBHX/TES system. A computer model of the FBHX/TES systems was developed and the technical feasibility of the two selected applications was verified. Economic and tradeoff evaluations in progress for final optimization of the systems and selection of the most promising system for further concept validation are described.

  9. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Introductory part and summaries

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan and comprises seven chapters. Chapter I briefly describes the importance of HLW management in promoting nuclear energy utilization. According to the long-term program, the HLW separated from spent fuels at reprocessing plants is to be vitrified and stored for a period of 30 to 50 years to allow cooling, then be disposed of in a deep geological formation. Chapter II mainly explains the concepts of geological disposal in Japan. Chapters III to V are devoted to discussions on three important technical elements (the geological environment of Japan, engineering technology and safety assessment of the geological disposal system) which are necessary for reliable realization of the geological disposal concept. Chapter VI demonstrates the technical ground for site selection and for setup of safety standards of the disposal. Chapter VII summarizes together with plans for future research and development. (Ohno, S.)

  10. An overview of research progress of adsorption and desorption of coal-Bed methane%煤层气吸附解吸研究进展综述

    Institute of Scientific and Technical Information of China (English)

    常广涛; 王一帆; 董特特

    2015-01-01

    对于煤层气吸附、解吸特征及机理的研究,是揭示煤层气成藏机理及高效开发煤层气的基础。通过对国内外文献资料的调研,详细论述了煤层气吸附解吸的机理和过程,介绍了影响煤层气吸附与解吸的因素以及各种煤层气吸附的数学模型,提出了煤层气吸附与解吸研究中存在的问题,进而为煤层气藏的高效、合理开发奠定理论基础。%The characteristics and mechanism research of coal-bed methane adsorption and desorption is the foundation of efficient development of coal-bed methane. The mechanism and process of adsorption and desorption of coal-bed methane are discussed in detail. The mathematical model and influencing factors as well as problems among the research are given. These can help to provide a theoretical foundation for the efficient,rational exploitation of coal-bed methane.

  11. Great Plains Coal Gasification Project: Quarterly technical progress report, April-June 1988 (Fourth fiscal quarter, 1987-1988)

    Energy Technology Data Exchange (ETDEWEB)

    1988-07-29

    This progress report describes the operation of the Great Plains Gasification Plant, including lignite coal production, SNG production, gas quality, by-products, and certain problems encountered. (LTN)

  12. Materials compatibility and lubricants research on CFC-refrigerant substitutes. Quarterly technical progress report, 1 October 1992--31 December 1992

    Energy Technology Data Exchange (ETDEWEB)

    Hourahan, G.C.; Szymurski, S.R.

    1993-01-01

    The materials Compatibility and Lubricants Research (MCLR) program supports critical research to accelerate the introduction of CFC-refrigerant substitutes. The MCLR program addresses refrigerant and lubricant properties and materials compatibility. The primary elements of the work include data collection and dissemination, materials compatibility testing, and methods development. The work is guided by an Advisory committee consisting of technical experts from the refrigeration and air-conditioning industry and government agencies. Under the current MCLR program the Air-Conditioning and Refrigeration Technology Institute, Inc., (ARTI) is contracting and managing multiple research projects and a data collection and dissemination effort. Preliminary results from these projects are reported in technical progress reports prepared by each researcher.

  13. 动力锂电池隔膜的技术要求及研究进展%Technical Requirements of Power Lithium Battery Diaphragm and Research Progress

    Institute of Scientific and Technical Information of China (English)

    李登科; 王丹

    2014-01-01

    This artical introduced the technical requirements of power lithium battery diaphragm, focused on the research progress of nonwoven membrane at home and abroad, nano fiber membrane, PA diaphragm, organic/inorganic composite film, ceramic coating membrane and other new diaphragm.%介绍了动力锂电池对隔膜的技术要求,重点介绍国内外无纺布隔膜、纳米纤维隔膜、PA隔膜,有机/无机复合膜,陶瓷涂层隔膜等新型隔膜的研究进展。

  14. GPHS-RTGs in support of the Cassini mission. Semi annual technical progress report, 2 October 1995--31 March 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-04-20

    The technical progress achieved during the period 2 October 1995 through 31 March 1996 on Contract No. DE-AC03-91SF18852, Radioisotope Generators and Ancillary Activities is described herein. This report is organized by the program task structure as follows: spacecraft integration and liaison; engineering support; safety; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment (GSE); RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance and reliability, contract changes, non-capital CAGO acquisition, and CAGO maintenance; contract acquired government-owned property (CAGO) acquisition; and program calendars.

  15. New York City School Survey 2008-2010: Assessing the Reliability and Validity of a Progress Report Measure. Technical Appendices

    Science.gov (United States)

    Nathanson, Lori; Cole, Rachel; Kemple, James J.; Lent, Jessica; McCormick, Meghan; Segeritz, Micha

    2013-01-01

    The Research Alliance for New York City Schools examined Department of Education (DOE) School Survey data from 2008-2010 to better understand the richness and complexities of the information elicited by the Survey from parents, students, and teachers. This document provides the appendices to the technical report "New York City School Survey…

  16. Design, construction, operation, and evaluation of a prototype culm-combustion boiler/heater unit. Quarterly technical progress report, October 1-December 31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-02-01

    This report provides a summary of the work performed on the Prototype Culm Combustion Boiler/Heater Unit, Phase I - Engineering Design and Analysis and Phase II - Prototype Plant Construction during the period October 1, 1980 through December 31, 1980. The objectives of the program as well as the technical progress and problem areas encountered during the reporting period are presented. The final detail design effort was completed and the final design report submitted. Progress on procurement activity authorized by full Phase II release on March 20, 1980, is discussed. Following approval by DOE, a purchase order was placed with the Norflor Construction Corporation for the prototype plant construction which began in November. Construction of the access roadway installation of the electric power, sewer and water lines was completed during this reporting period. Boiler construction continued.

  17. Bench-scale testing of on-line control of column flotation using a novel analyzer. Second quarterly technical progress report, January 1, 1993--March 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-04-16

    This document contains the second quarterly technical progress report for PTI`s Bench-Scale Testing Project of a circuit integrating PTI`s KEN-FLOTE{trademark} Column Flotation Technology and PTI`s On-Line Quality Monitor and Control System. The twelve-month project involves installation and testing of a 200--300 lb/hr. bench-scale testing circuit at PETC`s Coal Preparation Process Research Facility (CPPRF) for two bituminous coals (Upper Freeport and Pittsburgh No. 8 Seam Raw Coals). The project schedule timeline by task series for the twelve month project, as it was laid out in the initial Project Work Plan. At the present time, all tasks are progressing according to schedule with the exception of the Task 800 Circuit Testing and Sample Prep and Task 1000 Circuit Decommissioning, which have slipped approximately five weeks due to delays incurred within in the project.

  18. High-temperature-turbine technology program. Phase II. Technology test and support studies. Technical progress report, April 1, 1979-June 30, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1979-07-01

    Work performed on the High-Temperature-Turbine Technology Program, Phase II-Technology Test and Support Studies during the period from 1 April 1979 through 30 June 1979 is summarized. Objectives of the program elements as well as technical progress and problems during this Phase II quarterly reporting period are presented. Planned progress during the next quarterly reporting period is also defined. Testing of the LP rig engine with hot gas stream particulates simulating operation on low Btu gas is described. Fabrication of components and preparation of facilities for future tests of the Turbine Spool Technology Rig are discussed together with analytical reviews. Preparation of the low Btu gas synthesizing facility is discussed. Supporting Materials and Process investigations are described.

  19. Micropore diffusion in coal chars under reactive conditions: Quarterly technical progress report, 15 December 1986-15 March 1987. [Effect of activated diffusion in small pores

    Energy Technology Data Exchange (ETDEWEB)

    Calo, J.M.; Perkins, M.T.; Lilly, W.D.

    1987-01-01

    In this second quarterly technical progress report, we present some additional developments concerning the analysis of the effect of activated micropore diffusion on gasification reactivity, and report on progress with the experimental apparatus: (1) The Autoclave Engineers 3'' Berty catalytic reactor has been reassembled and tested, and has been found to function satisfactorily. However, the mass spectrometer malfunctioned and had to be repaired. (2) The effect of sorbate partial pressure on miropore diffusion and gasification reactivity have been examined. It was found that: pressure can have a significant effect on micropore diffusivities; increasing pressure generally increases the microparticle effectiveness factor for pressures far from saturation (while the opposite is true at near-saturation conditions); and the effect of sorbate partial pressure should be considered in conducting and interpreting measurements regarding micropore diffusion. 6 refs., 1 fig., 1 tab.

  20. Enhanced durability and reactivity for zinc ferrite desulfurization sorbent. Quarterly technical progress report 8, July--September 1988

    Energy Technology Data Exchange (ETDEWEB)

    Jha, M.C.; Berggren, M.H.

    1988-11-14

    AMAX Research & Development Center (AMAX R&D) has been investigating methods for enhancing the reactivity and durability of the zinc ferrite desulfurization sorbent. Zinc ferrite sorbents are intended for use in desulfurization of hot coal gas in integrated gasification combined cycle (IGCC) or molten carbonate fuel cell (MCFC) applications. For the present program, the reactivity of the sorbent may be defined as its sulfur sorption capacity at the breakthrough point and at saturation in a bench-scale, fixed-bed reactor. Durability may be defined as the ability of the sorbent to maintain important physical characteristics such As size, strength, and specific surface area during 10 cycles of sulfidation and oxidation.

  1. 双流化床生物质气化炉研究进展%Research progress of dual fluidized bed biomass gasifier

    Institute of Scientific and Technical Information of China (English)

    王晓明; 肖显斌; 刘吉; 陈旭娇; 覃吴; 董长青; 李文艳

    2015-01-01

    生物质是重要的清洁可再生能源,双流化床生物质气化技术是将低品位的生物质能转化成高品位氢能的重要途径。本文阐明了双流化床气化过程的基本原理,从燃气中氢气浓度、焦油含量和装置热效率等角度,介绍了双流化床生物质气化技术的早期探索和发展现状,对目前几种典型双流化床生物质气化炉的炉型设计及相关试验研究进行了分析和总结。指出内循环双流化床气化炉结构虽然简单紧凑,但是难以避免气化室和燃烧室之间的气体串混问题;而外循环流化床通过外置返料器很好地解决了气体串混问题。分析了不同气化室优化设计方案对提升燃气品质的理论依据及其优缺点。最后对双流化床生物质气化技术的发展进行了总结和展望,指出双流化床生物质气化制氢具有非常广阔的工业化应用和发展前景。%Biomass is an important part of clean and renewable energy sources. Dual fluidized bed biomass gasification is an important technology that transforms low-quality biomass into high-quality hydrogen. This paper illustrates the basic principles of the dual fluidized bed gasification process,and summarizes the early exploration and development status of the dual fluidized bed biomass gasification technology from the perspective of hydrogen concentration,tar content and device thermal efficiency. The furnace design and related experimental studies of several typical dual fluidized bed biomass gasifiers are analyzed and summarized. Internal circulating dual fluidized bed gasification furnace has simple and compact structure,but it is difficult to prevent gas leakage between gasification chamber and combustion chamber. External circulating dual fluidized bed with external recycle device resolves the problem of gas leakage. The theoretical basis,advantages and disadvantages of different optimized gasification chamber designs are analyzed. The

  2. Search for major genes with progeny test data to accelerate the development of genetically superior loblolly pine. Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-02-15

    This report details the progress of the three tasks of this project. The tasks are: (1) develop genetic models and analytical methods; (2) molecular confirmation of major gene segregation; and (3) develop strategies for marker-assisted breeding.

  3. Technical Division quarterly progress report, October 1--December 31, 1977. [Fuel cycle research and development; special materials production

    Energy Technology Data Exchange (ETDEWEB)

    Slansky, C.M. (ed.)

    1978-02-01

    Results are presented on the fluidized-bed calcination of simulated radioactive waste from the reprocessing of spent commercial nuclear fuel and on the removal of actinide elements from the waste prior to calcination. Other programs include the development of storage technology for /sup 85/Kr waste; and the behavior of volatile radionuclides during the combustion of HTGR graphite-based fuel. The long-term management of defense waste from the ICPP covers post-calcination treatment of ICPP calcined waste; the removal of actinide elements from first-cycle raffinate; the retrieval and handling of calcined waste from ICPP storage vaults; and the preparation of the Programmatic Environmental Impact Statement on ICPP waste. Process improvements are reported on the Fluorinel headend process for Zircaloy-clad fuels and on uranium accountability measurements. Other development results cover the process for recovering spent Rover fuel, buried pipeline transfer systems, support to the Waste Management Program, Waste Calcining Facility support, New Waste Calcining Facility support, and effluent monitoring methods evaluation and development. In this category are studies on nuclear materials security, application of a liquid-solid fluidized-bed heat exchanger to the recovery of geothermal heat, inplant reactor source term measurements, burnup methods for fast breeder reactor fuels, absolute thermal fission yield measurements, analytical support to light water breeder reactor development, research on analytical methods, and the behavior of environmental species of iodine.

  4. A systematic assessment of the state of hazardous waste clean-up technologies. Quarterly technical progress report, April 1--June 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Berg, M.T.; Reed, B.E.; Gabr, M.

    1993-07-01

    West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Report for Year 1 of the Agreement. This report reflects the progress and/or efforts performed on the following nine technical projects encompassed by the Year 1 Agreement for the period of April 1 through June 30, 1993: Systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies -- drain-enhanced soil flushing (DESF) for organic contaminants removal; site remediation technologies -- in situ bioremediation of organic contaminants; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors -- monolayer and multilayer self-assembled films for chemical sensors; Winfield lock and dam remediation; Assessments of Technologies for hazardous waste site remediation -- non-treatment technologies and pilot scale test facility implementation; and remediation of hazardous sites with stream reforming.

  5. A novel coal feeder for production of low sulfur fuel. Quarterly technical progress report, December 1, 1989--April 1, 1990

    Energy Technology Data Exchange (ETDEWEB)

    Keener, T.C.; Khang, S.J.; Yu, X.L.

    1990-12-31

    A novel coal feeding system is currently undergoing testing and evaluation at the University of Cincinnati. The system consists primarily of an auger feed tube which is used to both convey and provide desulfurization of a high sulfur coal feedstock. The coal is conveyed at temperatures ranging from 350 to 550 {degrees}C and under normal atmospheric pressure. Under these mild processing conditions, the coal partially pyrolizes and emits sulfur in the form of hydrogen sulfide while maintaining a relatively high heating value in the char product. The evolved gases are evacuated from the reactor (the feed tube) to another absorbing bed where H{sub 2}S reacts with the sorbent, usually lime or limestone. The resultant sorbent utilization is substantially higher than the values found in current dry scrubbing system and the produced low-sulfur char may then be used in a conventional steam boiler.

  6. Coal conversion. 1977 technical report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-06-01

    The status and progress in US DOE's projects in coal gasification, liquefaction, and fluidized-bed combustion are reviewed with financing, flowsheets, history, progress and status of each (57 projects). (LTN)

  7. Silicon ribbon growth by a capillary action shaping technique. Annual report (Quarterly technical progress report No. 9)

    Energy Technology Data Exchange (ETDEWEB)

    Schwuttke, G.H.; Ciszek, T.F.; Kran, A.

    1977-10-01

    Progress on the technological and economical assessment of ribbon growth of silicon by a capillary action shaping technique is reported. Progress in scale-up of the process from 50 mm to 100 mm ribbon widths is presented, the use of vitreous carbon as a crucible material is analyzed, and preliminary tests of CVD Si/sub 3/N/sub 4/ as a potential die material are reported. Diffusion length measurements by SEM, equipment and procedure for defect display under MOS structure in silicon ribbon for lifetime interpretation, and an assessment of ribbon technology are discussed. (WHK)

  8. Silicon ribbon growth by a capillary action shaping technique. Annual report (Quarterly technical progress report No. 9)

    Energy Technology Data Exchange (ETDEWEB)

    Schwuttke, G.H.; Ciszek, T.F.; Kran, A.

    1977-10-01

    Progress on the technological and economical assessment of ribbon growth of silicon by a capillary action shaping technique is reported. Progress in scale-up of the process from 50 mm to 100 mm ribbon widths is presented, the use of vitreous carbon as a crucible material is analyzed, and preliminary tests of CVD Si/sub 3/N/sub 4/ as a potential die material are reported. Diffusion length measurements by SEM, equipment and procedure for defect display under MOS structure in silicon ribbon for lifetime interpretation, and an assessment of ribbon technology are discussed. (WHK)

  9. Analysis and control of the METC fluid bed gasifier. Quarterly report, April 1995--June 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    This document summarizes work performed for the period 4/1/95 to 7/31/95 on contract no. DE-FG21-94MC31384 (Work accomplished during the period 10/1/94 to 3/31/94 was summarized in the previous technical progress report included in the appendix of this report). In this work, three components will form the basis for design of a control scheme for the Fluidized Bed Gasifier (FBG) at METC: (1) a control systems analysis based on simple linear models derived from process data, (2) review of the literature on fluid bed gasifier operation and control, and (3) understanding of present FBG operation and real world considerations. Tasks accomplished during the present reporting period include: (1) Completion of a literature survey on Fluid Bed Gasifier control, (2) Observation of the FBG during the week of July 17 to July 21, and (3) Suggested improvements to the control of FBG backpressure and MGCR pressure.

  10. 生物流化床处理废水的研究进展%Progress in fluidized bed bioreactor applied to wastewater treatment

    Institute of Scientific and Technical Information of China (English)

    冯杨阳; 廖延广; 陈英文; 沈树宝

    2014-01-01

    The fluidized bed bioreactor (FBBR) has attracted considerable interest due to the advantages,such as high treatment efficiency,high volume load,fast mass transfer and wide range of application. Its application to wastewater treatment in recent years is introduced. In addition , the main problems at present and development di-rection of fluidized bed bioreactor in the future are pointed out.%生物流化床技术因具有处理效率高、容积负荷大、传质速度快、应用范围广等优点受到了广泛的关注。介绍了近年来国内外生物流化床技术在废水处理中的应用研究情况,并指出了生物流化床技术目前存在的主要问题及今后的发展方向。

  11. Design, construction, operation and evaluation of a Prototype Culm Combustion Boiler/Heater Unit. Quarterly technical progress report, October 1-December 31, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-02-01

    This report provides a summary of the work performed on the Prototype Culm Combustion Boiler/Heater Unit, Phase I - Engineering Design and Analysis and Limited Phase II - Prototype Plant Construction during the period October 1, 1979 through December 31, 1979. The objectives of the program as well as the technical progress and problem areas encountered during the reporting period are presented. Progress on the components and system engineering studies is described. The Preliminary Design of Prototype Unit Topical Report was submitted during this reporting period. Final design activity is continuing and the progress on drawing preparation and advanced procurement activity is discussed. Based on authorization for a limited amount of Phase II activity, initial purchase orders were released authorizing preparation of certified drawings for fabricated equipment required to support the Phase I final design activity. The Purchase Order for site clearance and installation of boiler foundations was awarded during this reporting period and ground breaking ceremonies were held at the Prototype Culm Combustion Boiler site in Paxinos, Pennsylvania on December 7, 1979.

  12. High temperature turbine technology program. Phase II. Technology test and support studies. Annual technical progress report, January 1, 1979-December 31, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    Work performed on the High Temperature Turbine Technology Program, Phase II - Technology Test and Support Studies during the period from January 1, 1979 through December 31, 1979 is summarized. Objectives of the program elements as well as technical progress and problems encountered during this Phase II annual reporting period are presented. Progress on design, fabrication and checkout of test facilities and test rigs is described. LP turbine cascade tests were concluded. 350 hours of testing were conducted on the LP rig engine first with clean distillate fuel and then with fly ash particulates injected into the hot gas stream. Design and fabrication of the turbine spool technology rig components are described. TSTR 60/sup 0/ sector combustor rig fabrication and testing are reviewed. Progress in the design and fabrication of TSTR cascade rig components for operation on both distillate fuel and low Btu gas is described. The new coal-derived gaseous fuel synthesizing facility is reviewed. Results and future plans for the supporting metallurgical programs are discussed.

  13. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 2. Engineering technology for geological disposal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the deep geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, part 2 of the progress report, concerns engineering aspect with reference to Japanese geological disposal plan, according to which the vitrified HLW will be disposed of into a deep, stable rock mass with thick containers and surrounding buffer materials at the depth of several hundred meters. It discusses on multi-barrier systems consisting of a series of engineered and natural barriers that will isolate radioactive nuclides effectively and retard their migrations to the biosphere environment. Performance of repository components, including specifications of containers for vitrified HLW and their overpacks under design as well as buffer material such as Japanese bentonite to be placed in between are described referring also to such possible problems as corrosion arising from the supposed system. It also presents plans and designs for underground disposal facilities, and the presumed management of the underground facilities. (Ohno, S.)

  14. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 3. Safety assessment for geological disposal systems

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, the part 3 of the progress report, concerns safety assessment for geological disposal systems definitely introduced in part 1 and 2 of this series and consists of 9 chapters. Chapter I concerns the methodology for safety assessment while Chapter II deals with diversity and uncertainty about the scenario, the adequate model and the required data of the systems above. Chapter III summarizes the components of the geological disposal system. Chapter IV refers to the relationship between radioactive wastes and human life through groundwater, i.e. nuclide migration. In Chapter V is made a reference case which characterizes the geological environmental data using artificial barrier specifications. (Ohno. S.)

  15. Fossil Energy Program. Progress report for October 1979

    Energy Technology Data Exchange (ETDEWEB)

    McNeese, L.E.

    1979-12-01

    This report, the sixty-third of a series, is a compendium of monthly progress reports for the ORNL research and development programs that are in support of the increased utilization of coal and other fossil fuel alternatives to oil and gas as sources of clean energy. The projects reported this month include those for coal conversion development, materials engineering, a coal equipment test program, an atmospheric fluid bed combustor for cogeneration, engineering studies and technical support, process and program analysis, environmental assessment studies, magnetic beneficiation of dry pulverized coal, technical support to the TVA fluid bed combustion program, coal cogeneration/district heating plant assessment, chemical research and development, and technical support to major liquefaction projects.

  16. Fossil Energy Program. Progress report for September 1979

    Energy Technology Data Exchange (ETDEWEB)

    McNeese, L.E.

    1979-11-01

    This report - the sixty-second of a series - is a compendium of monthly progress reports for the ORNL research and development programs that are in support of the increased utilization of coal and other fossil fuel alternatives to oil and gas as sources of clean energy. The projects reported this month include those for coal conversion development, materials engineering, a coal equipment test program, an atmospheric fluidized bed combustor for cogeneration, engineering studies and technical support, process and program analysis, environmental assessment studies, magnetic beneficiation of dry pulverized coal, technical support to the TVA fluidized bed combustion program, coal cogeneration/district heating plant assessment, chemical research and development, and technical support to major liquefaction projects.

  17. Fossil Energy Program. Progress report for August 1979

    Energy Technology Data Exchange (ETDEWEB)

    McNeese, L.E.

    1979-10-01

    This report - the sixty-first of a series - is a compendium of monthly progress reports for the ORNL research and development programs that are in support of the increased utilization of coal and other fossil fuel alternatives to oil and gas as sources of clean energy. The projects reported this month include those for coal conversion development, materials engineering, a coal equipment test program, an atmospheric fluid bed combustor for cogeneration, engineering studies and technical support, process and program analysis, environmental assessment studies, magnetic beneficiation of dry pulverized coal, technical support to the TVA fluid bed combustion program, coal cogeneration/district heating plant assessment, chemical research and development, and technical support to major liquefaction projects.

  18. Neutron scatter studies of chromatin structures related to functions. Technical progress report, November 1, 1991--May 15, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Bradbury, E.M.

    1992-06-01

    We have made considerable progress in chromatin reconstitution with very lysine rich histone H1/H5 and in understanding the dynamics of nucleosomes. A ferromagnetic fluid was developed to align biological molecules for structural studies using small-angle-neutron-scattering. We have also identified and characterized in intrinsically bent DNA region flaking the RNA polymerase I binding site of the ribosomal RNA gene in Physarum Polycephalum. Finally projects in progress are in the areas of studying the interactions of histone H4 amino-terminus peptide 1-23 and acetylated 1-23 peptide with DNA using thermal denaturation; study of GGAAT repeats found in human centromeres using high resolution Nuclear Magnetic Resonance and nuclease sentivity assay; and the role of histones and other sperm specific proteins with sperm chromatin.

  19. Neutron scatter studies of chromatin structures related to functions. Technical progress report, November 1, 1991--May 15, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Bradbury, E.M.

    1992-11-01

    Despite of setbacks in the lack of neutrons for the proposed We have made considerable progress in chromatin reconstitution with the VLR histone H1/H5 and in understanding the dynamics of nucleosomes. A ferromagnetic fluid was developed to align biological molecules for structural studies using small-angle-neutron-scattering. We have also identified and characterized an intrinsically bent DNA region flanking the RNA polymerase I binding site of the ribosomal RNA gene in Physarum Polycephalum. Finally projects in progress are in the areas of studying the interatctions of histone H4 amino-terminus peptide 1-23 and acetylated 1-23 peptide with DNA using thermal denaturation; study of GGAAT repeats found in human centromeres using high resolution Nuclear magnetic Resonance and nuclease sentivity assay; and the role of histones and other sperm specific proteins with sperm chromatin.

  20. Technical progress report of biological research on the Volcanic Island Surtsey and its environs for the period 1965--1978

    Energy Technology Data Exchange (ETDEWEB)

    Fridriksson, S.

    1978-01-01

    Progress is reported on the following research projects: changes in shoreline and surface of the island due to volcanic activity; colonization of microorganisms, algae, lichens, and vascular plants; introduction of insects and other arthropods by wind, water, and man; transport of invertebrates to the island by flotsam of the sea; species and nesting habits of birds on the island; behavior of seals on beaches of the island; and future trends of Surtsey ecosystems. (HLW)

  1. 流化床膜反应器的应用研究进展%Research and development progress on fluidized bed membrane reactors

    Institute of Scientific and Technical Information of China (English)

    王长友; 韩艳丽; 赵洁; 解东来

    2012-01-01

    Two types of membranes have been employed in fluidized bed membrane reactors, hydrogen perm-selective membrane and oxygen perm-selective membranes. The studies focus on conceptual design of novel reactors, membrane fabrication and characterization, and reactor hydrodynamics. It is essential to study the coupling of chemical reaction and membrane separation in the future, to discover the influence of membrane on bed hydrodynamics, the influence of fluidization on membrane separation, and the coupling mechanisms of these two processes.%流化床膜反应器中所采用的膜主要有2类,一类为钯(及其合金)膜,另外一类为透氧膜.介绍了近十几年来流化床膜反应器的新型应用研究,主要集中在反应器概念设计、膜及其透过性能、以及流化床流体特性.提出未来有必要对流化床膜反应器中化学反应与膜分离过程的耦合这一关键科学问题进行深入的研究,揭示膜对流化床流体力学特性的影响和流化床对膜透过性能的影响机理,以及这两个过程的耦合机制.

  2. Engineering Development of Slurry Bubble Column Reactor (SBCR) Technology: Final quarterly technical progress no. 2, 1 July - 30 September 1995

    Energy Technology Data Exchange (ETDEWEB)

    Toseland, B.A.; Tischer, R.E.

    1997-12-31

    The major technical objectives of this program are threefold: (1) to develop the design tools and a fundamental understanding of the fluid dynamics of a slurry bubble column reactor to maximize reactor productivity, (2) to develop the mathematical reactor design models and gain an understanding of the hydrodynamic fundamentals under industrially relevant process conditions, and (3) to develop an understanding of the hydrodynamics and their interaction with the chemistries occurring in the bubble column reactor. Successful completion of these objectives will permit more efficient usage of the reactor column and tighter design criteria, increase overall reactor efficiency, and ensure a design that leads to stable reactor behavior when scaling up to large diameter reactors.

  3. POC-scale testing of an advanced fine coal dewatering equipment/technique. Quarterly technical progress report 2, January 1995--March 1995

    Energy Technology Data Exchange (ETDEWEB)

    Groppo, J.G.; Parekh, B.K.

    1995-05-05

    Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 {mu}m) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This project is a step in the Department of Energy`s program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The cost-sharing contract effort is for 36 months beginning September 30, 1994. This report discusses technical progress made during the quarter from January 1 to March 31, 1995.

  4. Humic substances in performance assessment of nuclear waste disposal: Actinide and iodine migration in the far-field. Second technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Buckau, G. (ed.)

    2004-07-01

    The present report describes progress within the second year of the EC-project ''Humic Substances in Performance Assessment of Nuclear Waste Disposal: Actinide and Iodine Migration in the Far-Field''. Without being a formal requirement of the commission or co-funding bodies, this report documents results in great technical detail. It is an open report and thus makes the detailed results available to a broad scientific community. The report contains an executive summary written by the coordinator. More detailed results are given as individual contributions in the form of 23 annexes. Not all results are discussed or referred to in the executive summary report and thus readers with a deeper interest also need to consult the annexes. (orig.)

  5. Increased oil production and reserves from improved completion techniques in the Bluebell Field, Uinta Basin, Utah. Seventh quarterly technical progress report, April 1, 1995--June 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Morgan, C.D.

    1995-09-01

    The objective of this project is to increase oil production and reserves in the Uinta Basin by demonstrating improved completion techniques. Low productivity of Uinta Basin wells is caused by gross production intervals of several thousand feet that contain perforated thief zones, water-bearing zones, and unperforated oil-bearing intervals. Geologic and engineering characterization and computer simulation of the Green River and Wasatch formations in the Bluebell field will determine reservoir heterogeneities related to fractures and depositional trends. This will be followed by drilling and recompletion of several wells to demonstrate improved completion techniques based on the reservoir characterization. Transfer of the project results will be an ongoing component of the project. Technical progress for this quarter are discussed for subsurface and engineering studies.

  6. An Investigation of the Mechanism of IGA/SCC of Alloy 600 in Corrosion Accelerating Heated Crevice Environments. Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    Lumsden, Jesse

    1999-01-01

    OAK-B135 An Investigation of the Mechanism of IGA/SCC of Alloy 600 in Corrosion Accelerating Heated Crevice Environments. Technical Progress Report. This program focuses on understanding the mechanisms causing corrosion damage to steam generator tubes in a pressurized water reactor (PWR) and the effects of the proposed remedial measures. The crevice formed by the tube/tube support plate (T/TSP) intersection in a PWR steam generator is a concentration site for nonvolatile impurities (referred to as hideout) in the steam generator water. The restricted mass transport in the small crevice volume prevents the species, which concentrate during the generation of steam, from quickly dispersing into the bulk water. The concentrated solutions in crevices have been a contributing cause of several forms of corrosion of steam generator tubes including intergranular attack/stress corrosion cracking (IGA/SCC), pitting, and wastage.

  7. The main technical progress directions in air-jet engine design branch, which are worked out by the “Single theory of continuous flow propulsions”

    Directory of Open Access Journals (Sweden)

    Борис Шамшадович Мамедов

    2016-03-01

    Full Text Available The main technical progress directions in air-jet engine design branch, which are worked out by the “Single theory of continuous flow propulsions” are highlighted. They are connected with providing the fly security by air-jet engines gas-dynamic work steady increasing with full elimination zone of rigid (spring stroke in the cross section B-B of the air-jet engines, with bypass turbojet engine’s thrust increasing with simultaneously fuel consumption lowering, with inlet and outlet decibel characteristic and radial dementias lowering, with high pressure compressor’s last working wheels blades increasing, with regulating law air-jet engine’s introduction to provide maximum thrust with the purpose of flying (thrust efficiency increasing

  8. Low-rank coal research under the UND/DOE cooperative agreement. Quarterly technical progress report, July-September 1983

    Energy Technology Data Exchange (ETDEWEB)

    Wiltsee, G.A. Jr.

    1983-01-01

    Two long gasification tests were accomplished (66 and 72 hours of slagging operation) this quarter, and the balance of the wastewater needed for the second cooling tower (CT) test (approx. 11,000 gallons) was generated. Eleven thousand gallons of slagging fixed-bed gasifier (SFBG) wastewater were solvent extracted and ammonia stripped (AS) to nominal levels of 160 mg/1 phenol and 600 mg/1 NH/sub 3/. This wastewater is being further treated by activated sludge (AS) and granular activated carbon (GAC) processing to prepare a high quality makeup for the second CT test. Phenol mass balances indicated that > 90 pct of the phenol was stripped from the tower, indicating that previous assumptions of high levels of biodegradation were erroneous. Over 80 pct of the ammonia and about 25 pct of the methanol were also stripped. Data collected during steady state operation of the bench-scale rotating biological contractor indicate complete removal of phenolics and alcohols, and 94 pct removal of BOD. Nitrification also occurred in this unit, with over 30 pct removal of ammonia. Problems due to individual bacteria, present in the biotreated wastewater, passing through the multi-media filter and thus decreasing the carbon adsorption efficiency of the GAC system, have resulted in lower treatment rates than originally anticipated. As a result, to achieve the desired treatment, the contact time of the wastewater with the carbon in the granular activated carbon system has been increased. Since this has decreased the treatment rate, a larger carbon adsorption system has been designed and is presently being constructed.

  9. High-temperature liquid-metal technology review. A Bimonthly Technical Progress Review, Volume 7, Number 2, April 1969

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    1969-04-01

    The purpose of the High-Temperature Liquid-Metal Technology Review is to provide up-to-date information on the various research and development programs in the United States in the field of high-temperature liquid-metal technology. The method is to publish reviews prepared by members of the Department of Applied Science of the Brookhaven National Laboratory on current topical and progress reports submitted by contracting organizations. When results and conclusions are reported, it is intended that the individual reviews become both summaries and critiques. Thirteen reviews are presented in this issue.

  10. THE BAUXITES AND JELAR - BEDS

    Directory of Open Access Journals (Sweden)

    Krešimir Sakač

    1993-12-01

    Full Text Available Minor bauxite deposits and occurrences were formed in technically disturbed environments in the middle part of the Adriatic geotectonic unit in Dinarides, contemporary with the clastic Jelar-beds in the Late Lutetian time. Uneven chemical composition of these Eocene bauxites, their sporadic occurrences in developed paleorelief as well as characteristic petrographic composition of the immediate overlying rocks point out at different genetical conditions (the paper is published in Croatian.

  11. Direct probing of chromatography columns by laser-induced fluorescence. Technical progress report, September 1, 1989--February 28, 1993

    Energy Technology Data Exchange (ETDEWEB)

    McGuffin, V.L.

    1992-12-07

    This report summarizes the progress and accomplishments of this research project from September 1, 1989 to February 28, 1993. During this period, we have accomplished all of the primary scientific objectives of the research proposal: (1) constructed and evaluated a laser-induced fluorescence detection system that allows direct examination of the chromatographic column, (2) examined nonequilibrium processes that occur upon solute injection and elution, (3) examined solute retention in liquid chromatography as a function of temperature and pressure, (4) examined solute zone dispersion in liquid chromatography as a function of temperature and pressure, and (5) developed appropriate theoretical models to describe these phenomena. In each of these studies, substantial knowledge has been gained of the fundamental processes that are responsible for chromatographic separations. In addition to these primary research objectives, we have made significant progress in three related areas: (1) examined pyrene as a fluorescent polarity probe insupercritical fluids and liquids as a function of temperature and pressure, (2) developed methods for the class-selective identification of polynuclear aromatic hydrocarbons in coal-derived fluids by microcolumn liquid chromatography with fluorescence quenching detection, and (3) developed methods for the determination of saturated and unsaturated (including omega-3) fatty acids in fish oil extracts by microcolumn liquid chromatography with laser-induced fluorescence detection. In these studies, the advanced separation and detection techniques developed in our laboratory are applied to practical problems of environmental and biomedical significance.

  12. 超重力旋转床中气液传质性能的研究进展%Progress on Performance of Gas-Liquid Mass Transference in Hypergravity Rotating Packet Bed

    Institute of Scientific and Technical Information of China (English)

    方健; 詹丽; 余国贤; 路平; 晋梅

    2015-01-01

    Rotating packed bed is a kind of new reaction device in industrial chemistry process ,used the centrifugal force generated by materials filling in high speed rotating to imitate the hypergravity enviro⁃ment ,the liquid contacted reversely with the gas phase at high relative velocity in curving hole of packing bed under the conditions of high dispersion ,high turbulence ,strong mixture and quick renew of inter⁃face ,it strongly intensified the gas-liquid mass transference. Reviewed the influence factors on the effect of gas-liquid mass transference in hypergravity rotating packed bed ,introduced the typical theory on gas-liquid mass transference ,moreover , introduced recent progress of the theory and the model of gas-liquid transference in hypergravity rotating packed bed ,prospected the intensifying technology in this field.%超重力旋转床是一种强化化学工业过程的新型反应器,利用高速旋转填料所产生的离心力来模拟超重力环境,液体在高分散、高湍动、强混合以及界面的快速更新下与气相以极大的相对速度在填料的弯曲孔道中进行逆向接触,极大地强化了气液传质过程而不液泛。对影响超重力旋转床气液传质效果的因素,如填料、转子转速以及气/液体流量等进行了综述,并在此基础上,介绍了典型的气液传质理论和近年来国内外对超重力旋转床中气液传质理论及气液传质模型的研究进展,最后对超重力旋转床气液传质的强化技术进行了展望。

  13. Advanced liquefaction using coal swelling and catalyst dispersion techniques. Quarterly technical progress report, April--June 1992

    Energy Technology Data Exchange (ETDEWEB)

    Curtis, C.W. [Auburn Univ., AL (United States); Gutterman, C. [Foster Wheeler Development Corp., Livingston, NJ (United States); Chander, S. [Pennsylvania State Univ., University Park, PA (United States)

    1992-08-26

    Research in this project centers upon developing a new approach to the direct liquefaction of coal to produce an all-distillate product slate at a sizable cost reduction over current technology. The approach integrates all aspects of the coal liquefaction process including coal selection, pretreatment, coal swelling with catalyst impregnation, coal liquefaction experimentation, product recovery with characterization, alternate bottoms processing, and a technical assessment including an economic evaluation. The project is being carried out under contract to the United States Department of Energy. On May 28, 1992, the Department of Energy authorized starting the experimental aspects of this projects; therefore, experimentation at Amoco started late in this quarterly report period. Research contracts with Auburn University, Pennsylvania State University, and Foster Wheeler Development Corporation were signed during June, 1992, so their work was just getting underway. Their work will be summarized in future quarterly reports. A set of coal samples were sent to Hazen Research for beneficiation. The samples were received and have been analyzed. The literature search covering coal swelling has been up-dated, and preliminary coal swelling experiments were carried out. Further swelling experimentation is underway. An up-date of the literature on the liquefaction of coal using dispersed catalysts is nearing completion; it will be included in the next quarterly report.

  14. Technical progress and energy substitutions in transport sector; Progres techniques et substitutions energetiques dans le secteur des transports

    Energy Technology Data Exchange (ETDEWEB)

    Florane, Philippe

    2002-11-15

    Alternative motorization technologies have been proposed in order to achieve energy diversification and a reduction in pollutant emissions. Fuel cell vehicles are, among others, at the centre of research carried out by car manufacturers and oil companies. The use of fuel cell vehicles could contribute, first, to a less stringent long-term energy dependence of oil importing countries and, second, to pollutant reduction in the transport sector. First of all, we propose the definition of 'innovation' and its treatment in the frame of mainstream economic theories. Then we proceed to a retrospective analysis of diesel motorization of the car market. In the second part of our work, we conduct a survey among French households aiming to obtain up-to-date information about their degree of acceptance of fuel cell technology. We are concerned about highlighting the determining factors of fuel cell vehicle adoption by consumers. For this, we set up a discrete choice model linking the individual decision to the whole group of technical or socio-economical factors and characteristics. Finally, we develop patterns of fuel cell equipment of passenger cars which differ according to type of vehicle and possible purchase assistance. These patterns lead us to the analysis of long-term fuel cell vehicle development on the French car market. (author)

  15. Combustion characteristics of Douglas Fir planer shavings. Technical progress report No. 4, September 16, 1977--September 15, 1978

    Energy Technology Data Exchange (ETDEWEB)

    Junge, D.C.

    1978-12-01

    Significant quantities of wood residue fuels are presently being used in industrial steam generating facilities. Recent studies indicate that substantial additional quantities of wood residue fuels are available for energy generation in the form of steam and/or electricity. A limited data base on the combustion characteristics of wood residue fuels has resulted in the installation and operation of inefficient combustion systems for these fuels. This investigation of the combustion characteristics of wood residue fuels was undertaken to provide a data base which could be used to optimize the combustion of such fuels. Optimization of the the combustion process in industrial boilers serves to improve combustion efficiency and to reduce air pollutant emissions generated in the combustion process. This report presents data on the combustion characteristics of Douglas Fir planer shavings. The data were obtained in a pilot scale combustion test facility at Oregon State Univerisity. Other technical reports present data on the combustion characteristics of: Douglas Fir bark, Red Alder sawdust, Red Alder bark, Ponderosa pine bark, Hemlock bark, and Eastern White Pine bark. An executive summary report is also available which compares the combustion characteristics of the various fuel species.

  16. Advanced liquefaction using coal swelling and catalyst dispersion techniques. Quarterly technical progress report No. 7, April 1993--June 1993

    Energy Technology Data Exchange (ETDEWEB)

    Curtis, C.W. [Auburn Univ., AL (United States); Chander, S. [Pennsylvania State Univ., University Park, PA (United States); Gutterman, C.

    1994-09-01

    The overall objective of this project is to develop a new approach for the direct liquefaction of coal to produce an all-distillate product slate at a sizable cost reduction over current technology. The approach integrates coal selection, pretreatment, coal swelling with catalyst impregnation, liquefaction, product recovery with characterization, alternate bottoms processing, and carrying out a technical assessment including an economic evaluation. The project is being carried out under contract to the United States Department of Energy. All three coals used in this study (Black Thunder, Burning Star bituminous, and Martin Lake lignite) are effectively swelled by a number of solvents. The most effective solvents are those having hetero-functionality. In addition, a synergistic effect has been demonstrated, in which solvent blends are more effective for coal swelling than the pure solvents alone. Therefore, it will be necessary to use only low levels of swelling agents and yet promote the impregnation of catalyst precursors. The rate of the impregnation of catalyst precursors into swollen coal increases greatly as the effectiveness of the solvent to swell the coal increases. This effect is also demonstrated by improved catalyst precursor impregnation with increased contact temperature. Laboratory- and bench-scale liquefaction experimentation is underway using swelled and catalyst impregnated coal samples. Higher coal conversions were observed for the SO{sub 2}-treated coal than the raw coal, regardless of catalyst type. Conversions of swelled coal were highest when Molyvan-L, molybdenum naphthenate, and nickel octoate, respectively, were added to the liquefaction solvent.

  17. Projects at the Western Environmental Technology Office. Quarterly technical progress report, July 1, 1995--September 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-01-01

    The goal of this project is to demonstrate the technical and economic feasibility of commercializing a biotechnology that uses plants to remediate soils, sediments, surface waters, and groundwaters contaminated by heavy metals and radionuclides. This technology, known as phytoremediation, is particularly suited to remediation of soils or water where low levels of contaminants are widespread. Project objectives are to provide an accurate estimate of the capability and rate of phytoremediation for removal of contaminants of concern from soils and groundwaters at Department of Energy (DOE) sites and to develop data suitable for engineering design and economic feasibility evaluations, including methods for destruction or final disposition of plants containing contaminants of concern. The bioremediation systems being evaluated could be less expensive than soil removal and treatment systems, given the areal extent and topography of sites under consideration and the investment of energy and money in soil-moving and -treating processes. In situ technology may receive regulatory acceptance more easily than ex situ treatments requiring excavation, processing, and replacement of surface soils. In addition, phytoremediation may be viable for cleanup of contaminated waters, either as the primary treatment or the final polishing stage, depending on the contaminant concentrations and process economics considerations.

  18. Development of precipitated iron Fischer-Tropsch catalysts. Quarterly technical progress report, 1 July 1995--30 September 1995

    Energy Technology Data Exchange (ETDEWEB)

    Bukur, D.B.

    1995-12-20

    The following accomplishments were made on task 4. Reproducibility of Catalyst Preparation: (1) Five slurry reactor tests were completed. Three tests were conducted using catalyst C (100 Fe/3 Cu/4 K/16 SiO{sub 2}) from three different batches (runs SB-2695, SB-2145 and SA-2715), and two tests were conducted with catalyst B (100 Fe/5 Cu/6 K/24 SiO{sub 2}) from two different preparation batches (runs SA-2615 and SB-2585). Performance of catalysts from different batches (activity, selectivity and deactivation rates) was similar to that of catalysts from the original batch (synthesized during DOE Contract DE- AC22-89PC89868). Thus, another major objective of the present contract, demonstration of reproducibility of catalyst preparation procedure and performance, has been accomplished. With these tests the work on Task 4 has been successfully completed. Two fixed bed reactor tests of catalysts B and C synthesized using potassium silicate solution as the source of potassium promoter were completed during this period (Task 5. The Effect of Source of Potassium and Basic Oxide Promoter). Activity of catalysts prepared using potassium silicate as the source of potassium promotion was somewhat higher, and their methane selectivities were higher than those of the corresponding catalysts prepared by incipient wetness impregnation using KHCO{sub 3} as the source of potassium promoter. However, these differences were not large, and may have been caused by experimental artifacts (e.g. existence of local hot spots in a reactor). A slurry reactor test (SA-2405) of catalyst with nominal composition 100 Fe/5 Cu/2 Ca/24 SiO{sub 2} was completed (Task 5). In general, the catalyst activity, space-time-yield, and hydrocarbon selectivities in this run during testing at:260{degrees}C, 2.17 MPa (300 psig), 2-2.6 Nl/g-cat/h and H{sub 2}CO=0.67 were quite good, and comparable to the best results obtained in our Laboratory.

  19. Follow on Research for Multi-Utility Technology Test Bed Aircraft at NASA Dryden Flight Research Center (FY13 Progress Report)

    Science.gov (United States)

    Pak, Chan-Gi

    2013-01-01

    Modern aircraft employ a significant fraction of their weight in composite materials to reduce weight and improve performance. Aircraft aeroservoelastic models are typically characterized by significant levels of model parameter uncertainty due to the composite manufacturing process. Small modeling errors in the finite element model will eventually induce errors in the structural flexibility and mass, thus propagating into unpredictable errors in the unsteady aerodynamics and the control law design. One of the primary objectives of Multi Utility Technology Test-bed (MUTT) aircraft is the flight demonstration of active flutter suppression, and therefore in this study, the identification of the primary and secondary modes for the structural model tuning based on the flutter analysis of MUTT aircraft. The ground vibration test-validated structural dynamic finite element model of the MUTT aircraft is created in this study. The structural dynamic finite element model of MUTT aircraft is improved using the in-house Multi-disciplinary Design, Analysis, and Optimization tool. In this study, two different weight configurations of MUTT aircraft have been improved simultaneously in a single model tuning procedure.

  20. Chaotic behavior monitoring & control in fluidized bed systems using artificial neural network. Quarterly progress report, July 1, 1996--September 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Bodruzzaman, M.

    1996-10-30

    We have developed techniques to control the chaotic behavior in Fluidized Bed Systems (FBC) systems using recurrent neural networks. For the sake of comparison of the techniques we have developed with the traditional chaotic system control methods, in the past three months we have been investigating the most popular and first known chaotic system control technique known as the OGY method. This method was developed by Edward Ott, Celso Grebogi and James York in 1990. In the past few years this method was further developed and applied by many researchers in the field. It was shown that this method has potential applications to a large cross section of problems in many fields. The only remaining question is whether it will prove possible to move from laboratory demonstrations on model systems to real world situations of engineering importance. We have developed computer programs to compute the OGY parameters from a chaotic time series, to control a chaotic system to a desired periodic orbit, using small perturbations to an accessible system parameter. We have tested those programs on the logistic map and the Henon map. We were able to control the chaotic behavior in such typical chaotic systems to period 1, 2, 3, 5..., as shown in some sample results below. In the following sections a brief discussion for the OGY method will be introduced, followed by results for the logistic map and Henon map control.

  1. SIMS three year study on statistics and environmental factors in health. Technical progress report No. 1. [Hazards of air pollution

    Energy Technology Data Exchange (ETDEWEB)

    None

    1976-12-01

    Progress is reported for the activities of the Siam Institute for mathematics and society (SIMS), Columbia University, and Stanford University. The SIMS report is concerned with the use of animal experiments in establishing tolerance limits for human exposure to environmental toxicants; valid assessment of the health consequences of occupational and other specialized toxic exposures; mathematical theories for the kinetics of carcinogenesis; data coding, storage, access, and analysis, relationship between air pollution and respiratory diseases; and air pollution assessment. The Columbia University report is concerned with development of statistical methods and models for describing the effects of the environment, measured by pollution and weather variables, on respiratory diseases. The Stanford University report is concerned with spatial distribution of air pollutants, relation of pollutant concentrations to morbidity and mortality statistics, and other topics. (HLW)

  2. High resolution, low cost solar cell contact development. Quarterly technical progress and schedule report, September 28, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Mardesich, N.

    1980-01-01

    The scope of the contract covers the development and evaluation of forming solar cell collector grid contacts by the MIDFILM process. This is a proprietary process developed by the Ferro Corporation which is a subcontractor for the program. The MIDFILM process attains line resolution characteristics of photoresist methods with processing related to screen printing. The surface to be processed is first coated with a thin layer of photoresist material. Upon exposure to ultraviolet light through a suitable mask, the resist in the non-pattern area cross-links and becomes hard. The unexposed pattern areas remain tacky. The conductor material is applied in the form of a dry mixture of metal and frit particles which adhere to the tacky pattern area. The assemblage is then fired to ash the photopolymer and sinter the fritted conductor powder. Effort was concentrated during this period on the establishment, optimization and identification of problem areas of the MIDFILM process. Progress is reported. (WHK)

  3. Technical progress report for the Magnetohydrodynamics Coal-Fired Flow Facility: October 1, 1992--December 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    1993-06-01

    Progress is reported on a multitask contract to develop technology for steam bottoming cycle of a Combined Cycle MHD Steam Power Plant. The report describes a 314 hour proof-of-concept (POC) test completed during the quarter. Results include secondary combustion and effect of potassium on the light-off temperature, fouling of heat transfer surfaces, particulate clean-up device performance and advanced diagnostic system performance. Test results on ceramic materials and tubes directed toward the development of a high temperature recuperative air heater are summarized. Results of data analysis of previous tests that are reported include the continuing analysis of tube materials that were exposed to 1500 and 2000 hours of eastern coal fired operation during the previously completed 2000 hour POC test series on eastern, high sulfur coal.

  4. Measurements of scattering processes in negative ion: Atom collisions. Technical progress report, 1 September 1991--31 December 1994

    Energy Technology Data Exchange (ETDEWEB)

    Kvale, T.J.

    1994-09-27

    This report describes the progress made on the research objectives during the past three years of the grant. This research project is designed to study various scattering processes which occur in H{sup {minus}} collisions with atomic (specifically, noble gas and atomic hydrogen) targets in the intermediate energy region. These processes include: elastic scattering, single- and double-electron detachment, and target excitation/ionization. For the elastic and target inelastic processes where H{sup {minus}} is scattered intact, the experimental technique of Ion Energy-Loss Spectroscopy (IELS) will be employed to identify the final target state(s). In most of the above processes, cross sections are unknown both experimentally and theoretically. The measurements will provide total cross sections (TCS) initially, and once the angular positioning apparatus is installed, will provide angular differential cross sections (ADCS).

  5. Development and Validation of a Novel Scoring System for Predicting Technical Success of Chronic Total Occlusion Percutaneous Coronary Interventions: The PROGRESS CTO (Prospective Global Registry for the Study of Chronic Total Occlusion Intervention) Score.

    Science.gov (United States)

    Christopoulos, Georgios; Kandzari, David E; Yeh, Robert W; Jaffer, Farouc A; Karmpaliotis, Dimitri; Wyman, Michael R; Alaswad, Khaldoon; Lombardi, William; Grantham, J Aaron; Moses, Jeffrey; Christakopoulos, Georgios; Tarar, Muhammad Nauman J; Rangan, Bavana V; Lembo, Nicholas; Garcia, Santiago; Cipher, Daisha; Thompson, Craig A; Banerjee, Subhash; Brilakis, Emmanouil S

    2016-01-11

    This study sought to develop a novel parsimonious score for predicting technical success of chronic total occlusion (CTO) percutaneous coronary intervention (PCI) performed using the hybrid approach. Predicting technical success of CTO PCI can facilitate clinical decision making and procedural planning. We analyzed clinical and angiographic parameters from 781 CTO PCIs included in PROGRESS CTO (Prospective Global Registry for the Study of Chronic Total Occlusion Intervention) using a derivation and validation cohort (2:1 sampling ratio). Variables with strong association with technical success in multivariable analysis were assigned 1 point, and a 4-point score was developed from summing all points. The PROGRESS CTO score was subsequently compared with the J-CTO (Multicenter Chronic Total Occlusion Registry in Japan) score in the validation cohort. Technical success was 92.9%. On multivariable analysis, factors associated with technical success included proximal cap ambiguity (beta coefficient [b] = 0.88), moderate/severe tortuosity (b = 1.18), circumflex artery CTO (b = 0.99), and absence of "interventional" collaterals (b = 0.88). The resulting score demonstrated good calibration and discriminatory capacity in the derivation (Hosmer-Lemeshow chi-square = 2.633; p = 0.268, and receiver-operator characteristic [ROC] area = 0.778) and validation (Hosmer-Lemeshow chi-square = 5.333; p = 0.070, and ROC area = 0.720) subset. In the validation cohort, the PROGRESS CTO and J-CTO scores performed similarly in predicting technical success (ROC area 0.720 vs. 0.746, area under the curve difference = 0.026, 95% confidence interval = -0.093 to 0.144). The PROGRESS CTO score is a novel useful tool for estimating technical success in CTO PCI performed using the hybrid approach. Copyright © 2016 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

  6. Coal-fired combustion system for industrial process heating applications. Quarterly technical progress report, April 1995--June 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-08-01

    PETC has implemented a number of advanced combustion research projects that will lead to the establishment of a broad, commercially acceptable engineering data base for the advancement of coal as the fuel of choice for boilers, furnaces, and process heaters. This includes new installations and those existing installations that were originally designed for oil or gas firing. The data generated by these projects must be sufficient for private-sector decisions on the feasibility of using coal as the fuel of choice. This work should also provide incentives for the private sector to continue and expand the development, demonstration, and application of these combustion systems. Vortec Corporation`s Coal-Fired Combustion System for Industrial Process Heating Applications is being developed under contract DE-AC22-91PC91161 as part of this DOE development program. The current contract represents the third phase of a three-phase development program. Phase I of the program addressed the technical and economic feasibility of the process, and was initiated in 1987 and completed 1989. Phase II was initiated in 1989 and completed in 1990. During Phase II of the development, design improvements were made to critical components and the test program addressed the performance of the process using several different feedstocks. Phase III of the program was initiated September 1991 and is scheduled for completion in 1994. The Phase III research effort is being focused on the development of a process heater system to be used for producing value-added vitrified glass products from boiler/incinerator ashes and selected industrial wastes.

  7. Innovative Clean Coal Technology (ICCT). Technical progress report, second & third quarters, 1993, April 1993--June 1993, July 1993--September 1993

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    The objective of this project is to demonstrate and evaluate commercially available Selective Catalytic Reduction (SCR) catalysts from U.S., Japanese, and European catalyst suppliers on a high-sulfur U.S. coal-fired boiler. SCR is a post-combustion nitrogen oxide (NOx) control technology that involves injecting ammonia into the flue gas generated from coal combustion in an electric utility boiler. The flue gas containing ammonia is then passed through a reactor that contains a specialized catalyst. In the presence of the catalyst, the ammonia reacts with NOx to convert it to nitrogen and water vapor. Although SCR is widely practiced in Japan and Europe on gas-, oil-, and low-sulfur coal-fired boilers, there are several technical uncertainties associated with applying SCR to U.S. coals. These uncertainties include: (1) potential catalyst deactivation due to poisoning by trace metal species present in U.S. coals that are not present in other fuels; (2) performance of the technology and effects on the balance-of-plant equipment in the presence of high amounts of SO{sub 2} and SO{sub 3}; and (3) performance of a wide variety of SCR catalyst compositions, geometries and methods of manufacture under typical high-sulfur coal-fired utility operating conditions. These uncertainties are being explored by constructing and operating a series of small-scale SCR reactors and simultaneously exposing different SCR catalysts to flue gas derived from the combustion of high sulfur U.S. coal. The demonstration is being performed at Gulf Power Company`s Plant Crist Unit No. 5 (75 MW capacity) near Pensacola, Florida. The project is funded by the U.S. Department of Energy (DOE), Southern Company Services, Inc. (SCS on behalf of the entire Southern electric system), the Electric Power Research Institute (EPRI), and Ontario Hydro. SCS is the participant responsible for managing all aspects of this project.

  8. Bed rest during pregnancy

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/patientinstructions/000581.htm Bed rest during pregnancy To use the sharing features on ... few days or weeks. This is called bed rest. Bed rest used to be recommended routinely for ...

  9. Establishment of an Institute for Fusion Studies. Technical progress report, 1 November 1993--31 October 1994

    Energy Technology Data Exchange (ETDEWEB)

    Hazeltine, R.D.

    1994-07-01

    The Institute for Fusion Studies is a national center for theoretical fusion plasma physics research. Its purposes are: (1) to conduct research on theoretical questions concerning the achievement of controlled fusion energy by means of magnetic confinement--including both fundamental problems of long-range significance, as well as shorter-term issues; (2) to serve as a national and international center for information exchange by hosting exchange visits, conferences, and workshops; (3) and to train students and postdoctoral research personnel for the fusion energy program and plasma physics research areas. The theoretical research results obtained by the Institute contribute to the progress of nuclear fusion research, whose goal is the development of fusion power as a basic energy source. Close collaborative relationships have been developed with other university and national laboratory fusion groups, both in the US and abroad. In addition to its primary focus on mainstream fusion physics, the Institute is also involved with research in fusion-sidestream fields, such as advanced computing techniques, nonlinear dynamics, space plasmas and astrophysics, statistical mechanics, fluid dynamics, and accelerator physics. Important research discoveries are briefly described.

  10. Molten Salt Coal Gasification Process Development Unit. Phase 2. Quarterly technical progress report No. 2, October-December 1980

    Energy Technology Data Exchange (ETDEWEB)

    Slater, M. H.

    1981-01-20

    This represents the second quarterly progress report on Phase 2 of the Molten Salt Coal Gasification Process Development Unit (PDU) Program. Phase 1 of this program started in March 1976 and included the design, construction, and initial operation of the PDU. On June 25, 1980, Phase 2 of the program was initiated. It covers a 1-year operations program utilizing the existing PDU and is planned to include five runs with a targeted total operating time of 9 weeks. During this report period, Run 6, the initial run of the Phase 2 program was completed. The gasification system was operated for a total of 95 h at pressures up to 10 atm. Average product gas HHV values of 100 Btu/scf were recorded during 10-atm operation, while gasifying coal at a rate of 1100 lb/h. The run was terminated when the melt overflow system plugged after 60 continuous hours of overflow. Following this run, melt withdrawal system revisions were made, basically by changing the orifice materials from Monofrax to an 80 Cobalt-20 Chromium alloy. By the end of the report period, the PDU was being prepared for Run 7.

  11. Molluscs and echinoderms aquaculture: biological aspects, current status, technical progress and future perspectives for the most promising species in Italy

    Directory of Open Access Journals (Sweden)

    Antonio Pais

    2012-10-01

    Full Text Available Shellfish aquaculture is a widespread activity in the Italian peninsula. However, only two bivalve species are mainly cultured along the coastline of that country: the Mediterranean mussel Mytilus galloprovincialis and the Manila clam Venerupis philippinarum (Ruditapes philippinarum. By contrast, just a few other mollusc species of commercial interest are scarcely reared at a small-scale level. After analysing the current status of Italian shellfish production, this paper reports and discusses the potential for culturing several different invertebrate species [i.e., the European flat oyster Ostrea edulis, the grooved carpet shell Venerupis decussata (Ruditapes decussatus, the razor clams Ensis minor and Solen marginatus, the cephalopod Octopus vulgaris, and the purple sea urchin Paracentrotus lividus] in this country. In addition, a detailed overview of the progress made in aquacultural techniques for these species in the Mediterranean basin is presented, highlighting the most relevant bottlenecks and the way forward to shift from the experimental to the aquaculture phase. Finally, an outlook of the main economic and environmental benefits arising from these shellfish culture practices is also given.

  12. Identification of sulfur heterocycles in coal liquids and shale oils. Technical progress report, August 1, 1980-May 1, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Lee, M. L.; Castle, R. N.

    1981-01-01

    The sulfur heterocycle separation scheme which was described in the last progress report was evaluated for quantitative recovery of individual components. The results indicate that recoveries can range from 10% to approx. 30% depending on the structure of the compound. During this period, 23 unsubstituted sulfur-containing heterocyclic ring systems were synthesized in oder to confirm GC/MS identifications and for biological testing. The four possible 3-ring heterocycles and the thirteen possible 4-ring heterocycles were tested for mutagenic activity in the histidine reversion (Ames assay) system. One of the 3-ring isomers, naphtho(1,2-b)-thiophene, and six of the 4-ring isomers induced mutations in Salmonella test strains. One of these compounds, phenanthro(3,4-b)thiophene, displayed approximately the same mutagenic activity as benzo(a)pyrene. A two-step adsorption chromatographic procedure was developed in order to fractionate synthetic fuels into various chemical-type classes for studying the relative concentrations and mutagenic activities of the various types. An SRC-II Heavy Distillate was fractionated into aliphatic hydrocarbons, polycyclic aromatic hydrocarbons, sulfur heterocycles, indoles and carbazoles, azaarenes, and amino polycyclic aromatic hydrocarbons. It was found that the amino-PAH fraction contained most of the mutagenic activity. A survey was made for compounds containing both nitrogen and sulfur heteroatoms in their structures. A number of these compounds were detected by GC using nitrogen- and sulfur-selective detection.

  13. 1991 Technical progress report of the University of South Carolina`s High Energy Physics Group, February 1990--July 1991

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-12-31

    The high energy physics group at the University of South Carolina includes five teaching faculty members, one research faculty member, and five graduate students. Profs. Childers, Darden, and Wilson devote most of their research effort to Fermilab experiment E789, which is designed to observe charmless two-body decays of b-flavored mesons and baryons. Prof. Wilson works on Fermilab experiment E687 which studies charm physics in the wide-band photon beam. Profs. Rosenfeld and Wang participate in the AMY collaboration, which studies electron-positron interactions using the TRISTAN collider at KEK. Prof. Rosenfeld and one student collaborate with personnel from KEK and INS, Tokyo, on an experiment to detect a 17 keV neutrino in the {beta}-decay spectrum of {sup 63}Ni. Members of the group also participate in Fermilab Proposal P803 which will search for the oscillation of muon neutrino to tau neutrino with sensitivity better than a factor of 40 than previously achieved and in Superconducting Super Collider activities which include the development of an imaging preradiator. A brief discussion is given on progress made for each program.

  14. Technical Progress Report for PEPCO: Turbo-Z Battery Charging System. Calendar Quarter Ending March 31, 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-04-01

    The project is proceeding at a rapid pace now. The software is in development for the control board and the test stand. Portions of the writing and debugging of this software have been in conjunction with the hardware development. The software now interfaces with all the measurement instruments and displays the measurements on the screen, and it saves the measurements to a disc file. There is still cleanup work to do on the display items. Work must still be imparted to the code to control a charging sequence while taking measurements of the results. The test stand hardware has received a good development effort this quarter. The timer-counter board is working in the computer. This board paces the measurement cycle and times the discharge pulse (whine circuit). The thermocouple multiplexer is scanning at the same time the analog to digital converter is taking measurements. We have made a good number of hardware modifications to solve problems revealed while writing the software. The power factor correction for the charger power section is still in development. The engineers have found additional sources for the PFC chips, and they have obtained more technical data sheets and acquired samples. The control board schematics are complete, and the software is far along in the development phase. The functions of the control board have been detailed. The control board must next be integrated with the power supply unit. The next phase of development will concentrate on integrating the components together. At this time, the final debugging of the hardware and software will begin. Additionally, the capacitive coupler development is proceeding. The annual DARPA/DoT Advanced Transportation review will be held on May 16, 1999. We expect to learn the status of our project proposal during this conference. Should we more forward, UL has agreed to help us determine the design requirements of the complete charging system at their EV testing facility, prior to manufacturing. This

  15. Continuous Fiber Wound Ceramic Composite (CFCC) for Commercial Water Reactor Fuel. Technical progress report for period ending April 1, 2000

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-04-01

    Our program began on August 1, 1999. As of April 1, 2000, the progress has been in materials selection and test planning. Three subcontracts are in place (McDermott Technologies Inc. for continuous fiber reinforced ceramic tubing fabrication, Swales Aerospace for LOCA testing of tubes, and Massachusetts Institute of Technology for In Reactor testing of tubes). With regard to materials selection we visited McDermott Technologies Inc. a number of times, including on February 23, 2000 to discuss the Draft Material Selection and Fabrication Report. The changes discussed at this meeting were implemented and the final version of this report is attached (attachment 1). McDermott Technologies Inc. will produce one type of tubing: Alumina oxide (Nextel 610) fiber, a carbon coating (left in place), and alumina-yttria matrix. A potentially desirable CFCC material of silicon carbide fiber with spinel matrix was discussed. That material selection was not adopted primarily due to material availability and cost. Gamma Engineering is exploring the available tube coatings at Northwestern University as a mechanism for reducing the permeability of the tubes, and thus, will use coating as a differentiating factor in the testing of tubing in the LOCA test as well as the In-Reactor Test. The conclusion of the Material Selection and Fabrication Report lists the possible coatings under evaluation. With regard to Test Planning, the MIT and Swales Aerospace have submitted draft Test Plans. MIT is attempting to accommodate an increased number of test specimens by evaluating alternative test configurations. Swales Aerospace held a design review at their facilities on February 24, 2000 and various engineering alternatives and safety issues were addressed. The final Test Plans are not expected until just before testing begins to allow for incorporation of changes during ''dry runs.''

  16. Heterogeneous kinetics of coal gasification. Quarterly technical progress report, 1 May 1982-31 July 1982. [Equipment design

    Energy Technology Data Exchange (ETDEWEB)

    Calo, J.M.

    1982-08-01

    During the reporting period significant progress was made on two fronts: (1) the steam addition system for transient steam-char kinetic experiments; and (2) the automated data acquisition system for rapid mass programming (control) of the mass spectrometer and data logging. Steam Addition System: Although it is a relatively straightforward matter to produce steam for the reactor, we found that it is quite a challenge to develop a system capable of maintaining a steady and accurately-known flow rate of steam-argon mixtures at high pressure and temperature in alternate flow circuits (i.e., the reactor and purge lines), while simultaneously protecting downstream valving and instrumentation. Thus, the scheme originally proposed has been modified to eliminate potential operating problems associated with the preliminary design. Automated Data Acquisition System: Although the CO/sub 2/ gasification data were obtained manually, the ultimate objective of the project to develop a quantitative understanding of the complete gasification rate process in the complex synthesis gas milieux calls for automated programming (control) of the mass spectrometer. In addition, the current mass spectrometer signal processing technique requires the use of a lock-in amplifier to extract the modulated portion of the total signal due to the beam species only, in an analog mode. In order to allow fast scanning of a number of species, the characteristic dwell time required by the lock-in amplifier on a particular mass peak must be decreased. These requirements are being met by implementing automated mass programming and data collection, and direct digital, phase-sensitive pulse counting.

  17. Progress in the establishment and strengthening of national immunization technical advisory groups: analysis from the 2013 WHO/UNICEF joint reporting form, data for 2012.

    Science.gov (United States)

    Duclos, Philippe; Dumolard, Laure; Abeysinghe, Nihal; Adjagba, Alex; Janusz, Cara Bess; Mihigo, Richard; Mosina, Liudmila; Takashima, Yashohiro; Oztürk, Murat Hakan

    2013-11-04

    The majority of industrialized and some developing countries have established National Immunization Technical Advisory Groups (NITAGs). To enable systematic global monitoring of the existence and functionality of NITAGs, in 2011, WHO and UNICEF included related questions in the WHO/UNICEF Joint Reporting Form (JRF) that provides an official means to globally collect indicators of immunization program performance. These questions relate to six basic process indicators. According to the analysis of the 2013 JRF, data for 2012, notable progress was achieved between 2010 and 2012 and by the end of 2012, 99 countries (52%) reported the existence of a NITAG with a formal legislative or administrative basis (with a high of 86% in the Eastern Mediterranean Region - EMR), among the countries that reported data in the NITAG section of the JRF. There were 63 (33%) countries with a NITAG that met six process indicators (47% increase over the 43 reported in 2010) including a total of 38 developing countries. 11% of low income countries reported a NITAG that meets all six process criteria, versus 29% of middle income countries and 57% of the high income ones. Countries with smaller populations reported the existence of a NITAG that meets all six process criteria less frequently than more populated countries (23% for less populated countries versus 43% for more populated ones). However, progress needs to be accelerated to reach the Global Vaccine Action Plan (GVAP) target of ensuring all countries have support from a NITAG. The GVAP represents a major opportunity to boost the institutionalization of NITAGs. A special approach needs to be explored to allow small countries to benefit from sub-regional or other countries advisory groups. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

  18. Features of formation spirituality pictures of the world in youth in in the era of information-highlytechnological scientific and technical progress

    Directory of Open Access Journals (Sweden)

    N. V. Polishchuk

    2016-06-01

    Full Text Available In clause necessity of formation of a spiritual picture of the world, anthropocosmos at young generation at the present stage of development much crisis world and, including, the Ukrainian society is proved. In the article the necessity of formation of anthropocosmos-spiritual picture of the world at young generation at the present stage of development bagalicious the world and, in particular, of the Ukrainian society. The proposed definition of new terms: anthropocosmos is a spiritual picture of the world, anthropocosmic spirituality, anthropocosmic worldview and other anthropocentric concepts and definitions in contemporary philosophical and pedagogical discourse. The presented model of the formation of anthropocosmos-spiritual worldview of the young generation in the information and high-tech scientific and technical progress and the author’s interpretation of its philosophical, educational, pedagogical and spiritual essence. It is proved, that having generated in consciousness of the young man a anthropocosmos-spiritual picture of the world, will allow it in conditions of inevitable crash in the near future of a human civilization, if it will not solve present global-civilizational crises and will not avoid geocosmic accidents, to understand sense space-ekzoplanete lives which will be esclusivi, and, therefore, crisis-free, conflict-free, comprehensive and meaningful, anthropocosmos-highly spiritual (divine M. Berdyaev, and, therefore, progressive and virtually eternal as the life of society, which is composed of such anthropocosmos educated individuals. Solved zagalnoosvitnioi sense anthropocosmos spiritual world picture, which is to solve the problem of the choice of life strategies of mankind, the search for new ways of civilization development, in particular, resettlement anthropocosmos-conscious part of humanity for exoplanets space with the aim of preserving the gene pool of humanity and creation of human cosmically

  19. Bench-scale testing of on-line control of column flotation using a novel analyzer. Quarterly technical progress report, September 21, 1992--December 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-01-22

    This document contains the first quarterly technical progress report for PTI`s Bench-Scale Testing Project of a circuit integrating PTI`s KEN-FLOTETM Column Flotation Technology and PTI`s On-Line Quality Monitor Control System. The twelve-month project will involve installation of a 300 lb/hr. bench-scale testing circuit at PETC`s Coal Preparation Process Research Facility (CPPRF) and testing of two bituminous coals (Upper Freeport and Pittsburgh No. 8 Seam Raw Coals). Figure 1 contains the project plan as well as the approach to completing the major tasks within the twelvemonth project. The project is broken down into three phases, which include: Phase I - Preparation: The preparation phase was performed principally at PTI`s Calumet offices from October through December, 1992. It involved building of the equipment and circuitry, as well as some preliminary design and equipment testing. Phase II - ET Circuit Installation and Testing: This installation and testing phase of the project will be performed at PETC`s CPPRF from January through May, 1993, and will be the major focus of the project. It will involve testing of the continuous 300 lb/hr. circuit. Phase II - Project Finalization: The project finalization phase will occur from June through September, 1993, at PTI`s Calumet offices and will involve finalizing analytical work and data evaluation, as well as final project reporting. This quarterly progress report principally summarizes the results from the Phase I preparation work and the plan for the early portions of the Phase 11 installation and commissioning, which will occur in January and the first week of February, 1993.

  20. Combined shift and methanation in a fluidized-bed reactor. Quarterly progress report, 1 October-31 December 1979. BCR report L-1061

    Energy Technology Data Exchange (ETDEWEB)

    Streeter, R C

    1980-01-01

    Construction of a new bench-scale methanation reactor is in progress. This system will provide the capability of adding steam to the feed gas. A bench-scale activity test, employing four samples of a Ni/Mo catalyst, was conducted using the existing life test system. Results showed that a spent catalyst sample containing 18 percent carbon was still as active as the fresh, as-received catalyst, thus confirming an earlier observation based on the results of PEDU Test No. 37. The activity of one sample that was previously heated at 450 C to remove the carbon seemed abnormally low. However, the results were inconclusive, and this sample will be tested further. No PEDU tests were scheduled. Some planned modifications to the PEDU reactor system are being delayed due to late delivery of a water injection pump and malfunctioning of new ball valves intended for installation on the catalyst sampling system. Arrangements have been made with Dr. Calvin Bartholomew of Brigham Young University to undertake continued studies on carbon deposition and catalyst regeneration. A research proposal submitted by Dr. Bartholomew has been reviewed and approved, and the BYU work is expected to commence early in January 1980.

  1. Progress and Challenges in Mainstreaming Climate Change in Federal Water Resources and Environmental Planning: Data Selection, Technical Methods, Decision Paradigms, and Climate Change Communication

    Science.gov (United States)

    Ferguson, I. M.; Gangopadhyay, S.; Elsner, M. M.; Broman, D.

    2016-12-01

    The Bureau of Reclamation (Reclamation) is a federal agency tasked with developing and managing water supply and hydropower projects throughout the Western U.S. Over the past decade, Reclamation and other federal agencies have adopted new guidelines, directives, and mandates that require consideration of climate change in water resources and environmental planning and decision making. The scientific community has developed a vast number of climate projections, along with an array of models and methods to evaluate potential impacts of climate change on hydrology and water resources. However, water resources engineers, planners, and decision makers continue to face challenges regarding how best to use the available data and tools to support major water resources decisions, including decisions regarding major infrastructure investments and long-term operating criteria. These decisions may affect local communities, national agricultural and energy economies, and critical environmental resources. Examples of challenges include: How to choose between the large number of available climate projection datasets? How to consider uncertainties in future climate while constraining the number of projections or scenarios analyzed to accommodate modeling resource limitations? How to communicate climate change information and uncertainties to decision makers, stakeholders, and the public? And, How to select a decision making framework when design or operating alternatives may differ between climate change scenarios. This presentation will discuss recent progress and ongoing challenges to integrating climate change information into water resources and environmental planning. Discussion will focus on the intersection between technical challenges and decision making paradigms through the lens of this federal water management agency.

  2. Development of vanadium-phosphate catalysts for methanol production by selective oxidation of methane. Quarterly technical progress report 10, July 1, 1995--September 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    McCormick, R.L.

    1995-12-07

    This document is the tenth quarterly technical progress report under Contract No. DE-AC22-92PC92110 {open_quotes}Development of Vanadium-Phosphate Catalysts for Methanol Production by Selective Oxidation of Methane{close_quotes}. Activities focused on testing of additional modified and promoted catalysts and characterization of these materials. Attempts at improving the sensitivity of our GC based analytical systems were also made with some success. Methanol oxidation studies were initiated. These results are reported. Specific accomplishments include: (1) Methane oxidation testing of a suite of catalysts promoted with most of the first row transition metals was completed. Several of these materials produced low, difficult to quantify yields of formaldehyde. (2) Characterization of these materials by XRD and FTIR was performed with the goal of correlating activity and selectivity with catalyst properties. (3) We began to characterize catalysts prepared via modified synthesis methods designed to enhance acidity using TGA measurements of acetonitrile chemisorption and methanol dehydration to dimethyl ether as a test reaction. (4) A catalyst prepared in the presence of naphthalene methanol as a structural disrupter was tested for activity in methane oxidation. It was found that this material produced low yields of formaldehyde which were difficult to quantify. (5) Preparation of catalysts with no Bronsted acid sites. This was accomplished by replacement of exchangeable protons with potassium, and (6) Methanol oxidation studies were initiated to provide an indication of catalyst activity for decomposition of this desired product and as a method of characterizing the catalyst surface.

  3. Design, construction, operation, and evaluation of a prototype culm combustion boiler/heater unit. Quarterly technical progress report, October 1-December 21, 1981

    Energy Technology Data Exchange (ETDEWEB)

    1982-01-01

    This report provides a summary of the work performed on the Prototype Culm Combustion Boiler/Heater Unit, Phase I - Engineering Design and Analysis, Phase II - Prototype Plant Construction and Phase III - Start-Up and Operation during the period October 1, 1981 through December 31, 1981. The objectives of the program as well as the technical progress and problem areas encountered during the reporting period are presented. Seven shakedown tests were run. Start-up and shakedown testing was completed. Four parametric tests were run. Performance data are presented with the exception of boiler efficiency which will be reported once chemical analyses are completed. Total boiler operation time through the end of this quarter - 1225 h, 50 min; operating time on culm and culm/limestone - 682 h, 43 min. Inspection revealed no problems with boiler tube wear. Sulfur capture greater than 94% was demonstrated (design is 88%). A turndown of better than 4 to 1 was shown (design is 2.5 to 1). Computer control of most of the loops has been successful and manual control was also demonstrated.

  4. Non-intrusive measurement of particle charge: Electrostatic dry coal cleaning. Technical progress report No. 8, April 1, 1993--June 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    As we reported in the Technical Progress Report No. 7, there are surges of electric current in the charging loop during triboelectrification of all particles. A high speed data acquisition and analysis system was developed to monitor and record the current pattern. There is no known report on such charge-discharge surges in the literature. The mechanism for it is yet to be understood. The on-line computerized electric current measurement also leads to an observation of charging effects as a function of particle feeding rate. It is shown that feed rate greatly alters particle charge. Such an effect is mostly overlooked by researchers and it could have a important role in process design where the feed rate would be maximized. The initial results for coal and mineral particles demonstrated that the average charge was lower when the feed rate was increased. Further investigation is scheduled to identify potential controlling factors, eg, the solid volume fraction and particle number density could be important process factors. The study of charging velocity and particle size was continued. It was found that particle charge was linearly dependent on the charging velocity for all samples investigated. However, the slope of this linear dependence varied for particles having different diameters. In addition, the charge-velocity relationships were dependent on feeding rates. Hence, the data discussed below include these interrelationships.

  5. Fossil energy program. Progress report for May 1980

    Energy Technology Data Exchange (ETDEWEB)

    McNeese, L.E.

    1980-08-01

    This report - the seventieth of a series - is a compendium of monthly progress reports for the ORNL research and development programs that are in support of the increased utilization of coal and other fossil fuel alternatives to oil and gas as sources of clean energy. The projects reported this month include those for coal conversion development, chemical research and development, materials technology, component and process evaluation studies, technical support to major liquefaction projects, process analysis and engineering evaluations, fossil energy environmental analysis, coal preparation and waste utilization, coal preparation plant automation, technical support to the TVA fluidized bed combustion demonstration plant program, coal cogeneration/district heating plant assessment, atmospheric fluidized bed coal combustor for cogeneration, performance assurance system support and international energy technology assessment.

  6. Fossil Energy Program. Progress report for April 1980

    Energy Technology Data Exchange (ETDEWEB)

    McNeese, L.E.

    1980-06-01

    This report - the sixty-ninth of a series - is a compendium of monthly progress reports for the ORNL research and development programs that are in support of the increased utilization of coal and other fossil fuel alternatives to oil and gas as sources of clean energy. The projects reported this month include those for coal conversion development, chemical research and development, materials technology, component and process evaluation studies, technical support to major liquefaction projects, process analysis and engineering evaluations, fossil energy environmental analysis, coal preparation and waste utilization, coal preparation plant automation, atmospheric fluidized bed coal combustor for cogeneration, technical support to the TVA fluidized bed combustion demonstration plant program, coal cogeneration/district heating plant assessment, performance assurance system support, and international energy technology assessment.

  7. Flue gas desulfurization by rotating beds

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, N.; Keyvani, M.; Coskundeniz, A.

    1992-01-01

    The operating and mass transfer characteristics of rotating foam metal beds were studied to determine the potential for flue gas desulfurization. This is a final technical report on the work supported by DOE [number sign]FG22-87-PC79924. The report is divided into two sections, Part 1 deals primarily with the operating characteristics of rotating beds, and Part 2 covers the mass transfer characteristics of S0[sub 2] absorption in water-lime slurries. Rotating foam metal beds are in essence packed towers operated in high gravitational fields. The foam metal bed is in the form of a cylindrical donut, or torus, and is rotated to produced the high centrifugal forces. The liquid phase enters the bed at the inner surface of the torus and is pulled by the field through the bed. Gas flows countercurrent to the liquid. The bed packing can have a very large specific surface areas and not flood. Possible benefits include much smaller height of a transfer unit resulting in smaller equipment and supporting structures, reduced solvent inventory, faster response with improved process control, reduced pressure drop, and shorter startup and shut-down times. This work is concerned broadly with the operating characteristics of rotating beds, the objectives being to (1) determine the pressure drop through the rotating bed; (2) determine the power required to operate the beds, (3) investigate the residence time distribution of the liquid phase in the beds; and (4) determine the mass transfer coefficients of S0[sub 2] absorption. Three packings of differing specific surface areas were studied, with areas ranging from 656 to 2952 m[sub 2]/m[sub 3]. Liquid flow rates to 36 kg/s*m[sub 2], gas flow rate to 2.2 kg/s*m[sub 2], and gravitational fields to 300 g were covered in this study.

  8. Rock bed heat accumulators. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Riaz, M.

    1977-12-01

    The principal objectives of the research program on rock bed heat accumulators (or RBHA) are: (1) to investigate the technical and economic feasibility of storing large amounts of thermal energy (in the tens of MWt range) at high temperature (up to 500/sup 0/C) over extended periods of time (up to 6 months) using native earth or rock materials; (2) to conduct studies to establish the performance characteristics of large rock bed heat accumulators at various power and temperature levels compatible with thermal conversion systems; and (3) to assess the materials and environmental problems associated with the operation of such large heat accumulators. Results of the study indicate that rock bed heat accumulators for seasonal storage are both technically and economically feasible, and hence could be exploited in various applications in which storage plays an essential role such as solar power and total energy systems, district and cogeneration heating systems.

  9. IRIS Final Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    M. D. Carelli

    2003-11-03

    OAK-B135 This NERI project, originally started as the Secure Transportable Autonomous Light Water Reactor (STAR-LW) and currently known as the International Reactor Innovative and Secure (IRIS) project, had the objective of investigating a novel type of water-cooled reactor to satisfy the Generation IV goals: fuel cycle sustainability, enhanced reliability and safety, and improved economics. The research objectives over the three-year (1999-2002) program were as follows: First year: Assess various design alternatives and establish main characteristics of a point design; Second year: Perform feasibility and engineering assessment of the selected design solutions; Third year: Complete reactor design and performance evaluation, including cost assessment These objectives were fully attained and actually they served to launch IRIS as a full fledged project for eventual commercial deployment. The program did not terminate in 2002 at the end of the NERI program, and has just entered in its fifth year. This has been made possible by the IRIS project participants which have grown from the original four member, two-countries team to the current twenty members, nine countries consortium. All the consortium members work under their own funding and it is estimated that the value of their in-kind contributions over the life of the project has been of the order of $30M. Currently, approximately 100 people worldwide are involved in the project. A very important constituency of the IRIS project is the academia: 7 universities from four countries are members of the consortium and five more US universities are associated via parallel NERI programs. To date, 97 students have worked or are working on IRIS; 59 IRIS-related graduate theses have been prepared or are in preparation, and 41 of these students have already graduated with M.S. (33) or Ph.D. (8) degrees. This ''final'' report (final only as far as the NERI program is concerned) summarizes the work performed in the first four years of IRIS, from October 1999 to October 2003. It provides a panoramic of the project status and design effort, with emphasis on the current status, since two previous reports have very extensively documented the work performed, from inception to early 2002.

  10. Research and development progresses in the mitigation and utilization of coal bed methane%煤层气治理与利用技术研究开发进展

    Institute of Scientific and Technical Information of China (English)

    李志凯; 秦张峰; 吴志伟; 赵建涛; 李树娜; 董梅; 樊卫斌; 王建国

    2013-01-01

    煤层气作为一种非常规天然气,既是宝贵的清洁能源,其主要成分甲烷同时也是一种主要的温室气体;煤层气的直接排放不仅加剧了大气温室效应和环境污染,同时也是能源资源的极大浪费.近年来,煤层气的治理和利用受到了广泛关注,有关技术研究和开发取得了很大进展.本文对近年来煤层气的治理和利用技术研发进展进行了总结和评估,侧重于介绍煤层气分离系统中关键的中、高浓度煤层气催化燃烧脱氧技术以及乏风瓦斯逆向流催化燃烧减排及余热利用技术.最后对煤层气综合利用技术进行了展望.%Coal bed methane (CBM) as an unconventional natural gas is a valuable energy resources;meanwhile the main content of CBM,methane,is also one of the most important gases that contribute towards inducing the greenhouse effect.The mitigation and utilization of coal bed methane,by reducing methane emissions and producing energy from recovered methane,can offer both opportunities to mitigate global climate change and to generate new sources of clean energy,which is therefore of great significance in both economic and environmental aspects and has received extensive attentions in recent years.In this paper,we attempt to make a review on the recent progresses of research and development in the mitigation and utilization of CBM.We focused mainly on the application of catalytic combustion in CBM mitigation and utilization,especially the deoxygenation of oxygen-bearing CBM,which is the key issue for methane concentration through pressure swing adsorption,as well as the mitigation and heat recovery of ventilation air methane (VAM) by using catalytic flow reversal reactor.Lastly,we would have an outlook on the possible technologies for the integrated utilization of CBM.

  11. The economical production of alcohol fuels from coal-derived synthesis gas. Quarterly technical progress report No. 5, October 1, 1992--December 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    1993-01-01

    Two base case flow sheets have now been prepared. In the first, which was originally presented in TPR4, a Texaco gasifier is used. Natural gas is also burned in sufficient quantity to increase the hydrogen to carbon monoxide ratio of the synthesis gas to the required value of 1. 1 for alcohol synthesis. Acid gas clean up and sulfur removal are accomplished using the Rectisol process followed by the Claus and Beavon processes. About 10% of the synthesis gas is sent to a power generation unit in order to produce electric power, with the remaining 90% used for alcohol synthesis. For this process, the estimated installed cost is $474.2 mm. The estimated annual operating costs are $64.5 MM. At a price of alcohol fuels in the vicinity of $1. 00/gal, the pay back period for construction of this plant is about four years. The details of this case, called Base Case 1, are presented in Appendix 1. The second base case, called Base Case 2, also has a detailed description and explanation in Appendix 1. In Base Case 2, a Lurgi Gasifier is used. The motivation for using a Lurgi Gasifier is that it runs at a lower temperature and pressure and, therefore, produces by-products such as coal liquids which can be sold. Based upon the economics of joint production, discussed in Technical Progress Report 4, this is a necessity. Since synthesis gas from natural gas is always less expensive to produce than from coal, then alcohol fuels will always be less expensive to produce from natural gas than from coal. Therefore, the only way to make coal- derived alcohol fuels economically competitive is to decrease the cost of production of coal-derived synthesis gas. one method for accomplishing this is to sell the by-products from the gasification step. The details of this strategy are discussed in Appendix 3.

  12. 技术进步对就业人力资本结构的影响%The Impact of Technical Progress on Human Capital Structure of Employment

    Institute of Scientific and Technical Information of China (English)

    黄犚

    2012-01-01

    利用2003-2010年省际面板数据,研究不同类型的技术进步对我国就业人力资本结构的影响.结果表明:总就业与就业结构的调整是矛盾的统一体;自主创新的技术进步对总就业的创造作用大于摧毁作用;外商直接投资和进出口贸易产生的引进技术进步有利于促进我国对外经济体转型升级,增加高人力资本需求;我国对外直接投资作为贸易的补充有利于增加我国总就业,但由于技术获取动力不足,吸收技术溢出的效果不明显,不具有高人力资本偏态效应.同时,该影响也表现出一定程度的区域差异.%Using the provincial panel data from 2003 to 2010, this paper studies the influence of different types of technical progress of the human capital structure of employment in China. The result shows that: total employment and employment structure adjustment are the unity of contradiction; independent innovation benefits job creation; FDI and foreign trade promote the transformation and upgrading of Chinas foreign economy, and thus increase the demand of high human capital; China's technology sourcing OFDI is underpowered; as a supplement to trade, it will be beneficial to increase total employment; but the technology spillover effect is not obvious. Meanwhile, the effect is different in areas.

  13. Thin films of gallium arsenide on low-cost substrates. Quarterly technical progress report No. 8 and topical report No. 3, April 2-July 1, 1978

    Energy Technology Data Exchange (ETDEWEB)

    Ruth, R.P.; Dapkus, P.D.; Dupuis, R.D.; Johnson, R.E.; Manasevit, H.M.; Moudy, L.A.; Yang, J.J.; Yingling, R.D.

    1978-07-01

    The seventh quarter of work on the contract is summarized. The metalorganic chemical vapor deposition (MO-CVD) technique has been applied to the growth of thin films of GaAs and GaAlAs on inexpensive polycrystalline or amorphous substrate materials (primarily glasses and metals) for use in fabrication of large-area low-cost photovoltaic device structures. Trimethylgallium (TMG), arsine (AsH/sub 3/), and trimethylaluminum (TMAl) are mixed in appropriate concentrations at room temperature in the gaseous state and pyrolyzed at the substrate, which is heated in a vertical reactor chamber to temperatures of 725 to 750/sup 0/C, to produce the desired film composition and properties. The technical activities during the quarter were concentrated on (1) a continuing evaluation of various graphite materials as possible substrates for MO-CVD growith of the polycrystalline GaAs solar cells; (2) attempts to improve the quality (especially the grain size) of polycrystalline GaAs films on Mo sheet and Mo/glass substrates by using HCl vapor during the MO-CVD growith process; (3) further studies of the transport properties of polycrystalline GaAs films, wth emphasis on n-type films; (4) continuing investigations of the properties of p-n junctions in polycrystalline GaAs, with emphasis on the formation and properties of p/sup +//n/n/sup +/ deposited structures; and (5) assembling apparatus and establishing a suitable technique for producing TiO/sub 2/ layers for use as AR coatings on GaAs cells. Progress is reported. (WHK)

  14. Bed Bugs - Multiple Languages

    Science.gov (United States)

    ... Are Here: Home → Multiple Languages → All Health Topics → Bed Bugs URL of this page: https://medlineplus.gov/languages/ ... V W XYZ List of All Topics All Bed Bugs - Multiple Languages To use the sharing features on ...

  15. Bed Bugs and Schools

    Science.gov (United States)

    Bed bugs have long been a pest – feeding on blood, causing itchy bites and generally irritating their human hosts. They are successful hitchhikers, and can move from an infested site to furniture, bedding, baggage, boxes, and clothing.

  16. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball and W. Zeuner

    2011-01-01

    In this report we will review the main achievements of the Technical Stop and the progress of several centrally-managed projects to support CMS operation and maintenance and prepare the way for upgrades. Overview of the extended Technical Stop  The principal objectives of the extended Technical Stop affecting the detector itself were the installation of the TOTEM T1 telescopes on both ends, the readjustment of the alignment link-disk in YE-2, the replacement of the light-guide sleeves for all PMs of both HFs, and some repairs on TOTEM T2 and CASTOR. The most significant tasks were, however, concentrated on the supporting infrastructure. A detailed line-by-line leak search was performed in the C6F14 cooling system of the Tracker, followed by the installation of variable-frequency drives on the pump motors of the SS1 and SS2 tracker cooling plants to reduce pressure transients during start-up. In the electrical system, larger harmonic filters were installed in ...

  17. Introduction to Bed Bugs

    Science.gov (United States)

    ... that there are ways to control bed bugs. Getting good, solid information is the first step in both prevention and control. While there is no chemical quick fix, there are effective strategies to control bed bugs involving both non-chemical and chemical methods. Bed bugs can be hard to find and ...

  18. Collaborative Strategy on Bed Bugs

    Science.gov (United States)

    The Collaborative Strategy on Bed Bugs was developed by the Federal Bed Bug Workgroup to clarify the federal role in bed bug control and highlight ways that government, community, academia and private industry can work together on bed bug issues.

  19. Humic substances in performance assessment of nuclear waste disposal: Actinide and iodine migration in the far-field. Third technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Buckau, G.

    2005-04-01

    The present report describes progress within the third and final year of the EC-project 'Humic Substances in Performance Assessment of Nuclear Waste Disposal: Actinide and Iodine Migration in the Far-Field'. The work conducted within the present project builds on a number of previous activities/project supported by the Commission. It finds its continuation within different EC FP 6 instruments and also provides for additional continued cooperation through network structures resulting from the broad cooperation within the project. Without being a formal requirement of the Commission or co-funding bodies, this report documents results in great technical detail and makes the results available to a broad scientific community. The report contains an executive summary written by the coordinator. More detailed results are given as individual contributions in the form of 12 annexes. Not all results are discussed or referred to in the executive summary report and thus readers with a deeper interest also need to consult the annexes. The overall objectives were to generate knowledge about the impact of humic substances on the migration of actinides and iodine in the far-field of a nuclear waste repository. In the beginning, focus was rather on the potential enhancement due to humic colloid mediated radionuclide transport. Thereby, sources, inventory, stability and mobility of dissolved humic substances in their colloidal form formed a key topic. Other key topics were the interaction with actinides and iodine, transport studies under near-natural conditions in the laboratory, rationalization of knowledge in models and application to three migration cases for visualization of the overall outcome. Changes relative to the original objectives were given by moving emphasis of natural chemical analogue studies from the question of kinetic exchange constants for different inventories in natural and laboratory systems to the study of anthropogenic actinide contaminants in the

  20. Application and research progress of fluidized bed-chemical vapor deposition technology%流化床-化学气相沉积技术的应用及研究进展

    Institute of Scientific and Technical Information of China (English)

    刘荣正; 刘马林; 邵友林; 刘兵

    2016-01-01

    Fluidized bed-chemical vapor deposition (FB-CVD) is widely used in industrial production owing to the combined advantages of both fluidized bed and chemical vapor deposition. Providing good heat and mass transfer,it can obtain a pure product with uniform deposition. Based on its basic principle,the applications of FB-CVD in areas of particle coating,preparation of one-dimensional nano-materials, polycrystalline silicon,powder synthesis and powder surface modification are reviewed. The progress of process simulation and reactor structure design of FB-CVD is introduced. From the discussion,the scientific connotation of FB-CVD shows multi-scale features,namely material preparation at microscopic level, particle fluidization at mesoscopic level and reactor structure design at macroscopic level. Future development of FB-CVD technology depends on coupling analysis of these three scales,and research should be focused on the effect of interaction between different scales,such as coupling between homogeneous nucleation material/non-homogeneous nucleation in materials preparation and particle fluidization in the reactor.%流化床-化学气相沉积(FB-CVD)技术是一种多学科交叉的材料制备技术,兼有流化床传热传质性能良好以及化学气相沉积均匀、产物单一等优点,在工业生产中有着广泛的应用,但因其属于交叉学科,散见于各种研究,没有进行专门的进展评述。本文拟对 FB-CVD 的工业应用进行专题综述,分析其发展和研究趋势。首先探讨了 FB-CVD 的基本原理,分别综述了其在颗粒包覆、一维纳米材料、多晶硅制备、颗粒表面改性及粉体制备等方面的应用,介绍了 FB-CVD 的过程模拟及反应器结构优化方面的研究进展。通过以上讨论,梳理了FB-CVD研究的科学内涵。可以看出,该过程具有明显的多尺度特征,即材料制备的微观层次、颗粒流化均匀性的介观层次以及反应器结构

  1. Fossil Energy Program. Progress report for November 1979. [35 Wt % Illinois No. 6 coal with Wilsonville recycle solvent

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    This report - the sixty-fourth of a series - is a compendium of monthly progress reports for the ORNL research and development programs that are in support of the increased utilization of coal and other fossil fuel alternatives to oil and gas as sources of clean energy. The projects reported this month include those for coal conversion development, materials engineering, a coal equipment test program, an atmospheric fluid bed combustor for cogeneration, engineering studies and technical support, process and program analysis, environmental assessment studies, magnetic beneficiation of dry pulverized coal, technical support to the TVA fluid bed combustion program, coal cogeneration/district heating plant assessment, chemical research and development, and technical support to major liquefaction projects.

  2. Currents induced by vertical varied radiation stress in standing waves and evolution of the bed composed of fine sediments

    Institute of Scientific and Technical Information of China (English)

    Jing-Xin ZHANG; Hua LIU

    2009-01-01

    This paper extends the conventional concept of radiation stress (Longuet-Higgins and Stewart, 1964)in progressive water waves to standing waves, so that its vertical profile could be defined and calculated in a new technical way. The hydrodynamic numerical model being coupled with the vertically varying radiation stress in standing waves is used to simulate the currents being induced by standing waves in the vertical section. Numerical modeling of suspended sediment transport is then carried out to simulate the evolution of the bed composed of fine sediments by the currents. The scour and deposition patterns simulated are in qualitative agreement with prior laboratory and field observations.

  3. TECHNICAL COORDINATION

    CERN Multimedia

    Austin Ball

    Summary of progress since last CMS week. Ten years of construction work have been completed. CMS is closed, in very close to the ideal low luminosity configuration, and performed well in the first tests with LHC beam. Behind this encouraging news is the story of a summer of intense commitment by many teams (from the collaboration and 3 CERN departments) working together, against the clock and despite many minor setbacks, to ensure that the experiment was ready to play a leading role in the excitement of September 10. Following beampipe bakeout and refill with pure neon, a magnificent effort by the ECAL group and the pt 5 technical crew made it possible to install and commission all 4 ECAL endcap Dees before the end of August. In the shadow of this activity, the barrel and forward pixel trackers and part of the beam monitoring were installed within the vac tank. The pt 5 technical teams then succeeded in safely removing the 20t installation tables and their support blocks from beneath the already installed ...

  4. A Primer on Wound Bed Preparation

    OpenAIRE

    Gokoo, Chuck

    2009-01-01

    Successful wound closure and healing are a major concern for today's clinician. Determining if the wound will progress or not relies on a comprehensive assessment, recognition of wound characteristics that will promote or impede the healing process and preparing the wound bed such that pathological features are removed allowing the healing cascade to occur. When complications are no longer a roadblock the wound will achieve a stable microenvironment and progress through the normal repairative...

  5. Increased oil production and reserves from improved completion techniques in the Bluebell field, Uinta Basin, Utah. Tenth quarterly technical progress report, January 1, 1996--March 31, 1996. Revised

    Energy Technology Data Exchange (ETDEWEB)

    Allison, M.L.

    1996-05-13

    The objective of this project is to increase oil production and reserves in the Uinta Basin by demonstrating improved completion techniques. Low productivity of Uinta Basin will is caused by gross production intervals of several thousand feet that contain perforated thief zones, water-bearing zones, and unperforated oil- bearing intervals. Geologic and engineering characterization and computer simulation of the Green River and Wasatch Formations in the Bluefell field will determine reservoir heterogeneities related to fractures and depositional trends. This will be followed by techniques based on the reservoir characterization. Transfer of the project results will be an ongoing component of the project. Data (net pay thickness, porosity, and water saturation) of more than 100 individuals beds in he lower Green River and Wasatch Formations were used to generate geostatistical realization (numerical- representation) of the reservoir properties. The data set was derived from the Michelle Ute and Malnar Pike demonstration wells and 22 other wells in a 20 (52 km{sup 2}) square-mile area. Beds were studied independently of each other. Principles of sequential Gaussian simulations were used to generate geostatistical realizations of the beds.

  6. Bed Stability and Debris Flow Erosion: A Dynamic "Shields Criterion" Associated with Bed Structure

    Science.gov (United States)

    Longjas, A.; Hill, K. M.

    2015-12-01

    Debris flows are mass movements that play an important role in transporting sediment from steep uplands to rivers at lower slopes. As the debris flow moves downstream, it entrains materials such as loose boulders, gravel, sand and mud deposited locally by shorter flows such as slides and rockfalls. To capture the conditions under which debris flows entrain bed sediment, some models use something akin to the Shields' criterion and an excess shear stress of the flow. However, these models typically neglect granular-scale effects in the bed which can modify the conditions under which a debris flow is erosional or depositional. For example, it is well known that repeated shearing causes denser packing in loose dry soils, which undoubtedly changes their resistance to shear. Here, we present laboratory flume experiments showing that the conditions for entrainment by debris flows is significantly dependent on the aging of an erodible bed even for narrowly distributed spherical particles. We investigate this quantitatively using particle tracking measurements to quantify instantaneous erosion rates and the evolving bed structure or "fabric". With progressive experiments we find a signature that emerges in the bed fabric that is correlated with an increasing apparent "fragility" of the bed. Specifically, a system that is originally depositional may become erosional after repeated debris flow events, and an erodible bed becomes increasingly erodible with repeated flows. We hypothesize that related effects of bed aging at the field scale may be partly responsible for the increasing destructiveness of secondary flows of landslides and debris flows.

  7. TECHNICAL COORDINATION

    CERN Multimedia

    Austin Ball

    2013-01-01

      Since the last report, much visible progress has been made, as the LS1 programme approaches the halfway point. From early October, technical and safety shift-crew have been present around the clock, allowing detectors to stay switched on overnight, ensuring that safety systems are operational and instructions for non-expert shift-crew are clear. LS1 progress Throughout the summer, whilst the solenoid vacuum tank and YB0 surfaces were accessible, an extensive installation programme took place to prepare for Tracker colder operation and the PLT installation, in 2014, the Phase 1 Pixel Tracker installation, in 2016–’17, and the HCAL Phase 1 upgrade completion, ending in LS2. This included pipework for N2 or dry air to flush the Tracker bulkhead region, many sensors to monitor temperature and dew point in the Tracker and its service channels, heating wires outside the Tracker cooling bundles, supports for the new vacuum-jacketed, concentric, CO2 Pixel cooling lines, the PLT cool...

  8. Materials compatibility and lubricants research on CFC-refrigerant substitutes. Quarterly MCLR program technical progress report, January 1, 1995--March 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Szymurski, S.R.; Hourahan, G.C.; Godwin, D.S.

    1995-04-01

    The Materials Compatibility and Lubricants Research (MCLR) program supports critical research to accelerate the introduction of CFC and HCFC refrigerant substitutes. The MCLR program addresses refrigerant and lubricant properties and materials compatibility. The primary elements of the work include data collection and dissemination, materials compatibility testing, and methods development. The work is guided by an Advisory Committee consisting of technical experts from the refrigeration and air-conditioning industry and government agencies. The Air-Conditioning and Refrigeration Technology Institute, Inc., (ARTI) manages and contracts multiple research projects and a data collection and dissemination effort. Detailed results from these projects are reported in technical reports prepared by each subcontractor.

  9. Fluidized bed calciner apparatus

    Science.gov (United States)

    Owen, Thomas J.; Klem, Jr., Michael J.; Cash, Robert J.

    1988-01-01

    An apparatus for remotely calcining a slurry or solution feed stream of toxic or hazardous material, such as ammonium diurante slurry or uranyl nitrate solution, is disclosed. The calcining apparatus includes a vertical substantially cylindrical inner shell disposed in a vertical substantially cylindrical outer shell, in which inner shell is disposed a fluidized bed comprising the feed stream material to be calcined and spherical beads to aid in heat transfer. Extending through the outer and inner shells is a feed nozzle for delivering feed material or a cleaning chemical to the beads. Disposed in and extending across the lower portion of the inner shell and upstream of the fluidized bed is a support member for supporting the fluidized bed, the support member having uniform slots for directing uniform gas flow to the fluidized bed from a fluidizing gas orifice disposed upstream of the support member. Disposed in the lower portion of the inner shell are a plurality of internal electric resistance heaters for heating the fluidized bed. Disposed circumferentially about the outside length of the inner shell are a plurality of external heaters for heating the inner shell thereby heating the fluidized bed. Further, connected to the internal and external heaters is a means for maintaining the fluidized bed temperature to within plus or minus approximately 25.degree. C. of a predetermined bed temperature. Disposed about the external heaters is the outer shell for providing radiative heat reflection back to the inner shell.

  10. Increased oil production and reserves utilizing secondary/tertiary recovery techniques on small reservoirs in the Paradox Basin, Utah. Technical progress report, January 1--March 31, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Allison, M.L.

    1996-04-30

    The primary objective of this project is to enhance domestic petroleum production by demonstration and technology transfer of an advanced oil recovery technology in the Paradox basin, southeastern Utah. If this project can demonstrate technical and economic feasibility, the technique can be applied to approximately 100 additional small fields in the Paradox basin alone, and result in increased recovery of 150 to 200 million barrels of oil. This project is designed to characterize five shallow-shelf carbonate reservoirs in the Pennsylvanian (Desmoinesian) Paradox Formation and choose the best candidate for a pilot demonstration project for either a waterflood or carbon dioxide-(CO{sub 2}-)flood project. The field demonstration, monitoring of field performance, and associated validation activities will take place in the Paradox basin within the Navajo Nation. The results of this project will be transferred to industry and other researchers through a petroleum extension service, creation of digital databases for distribution, technical workshops and seminars, field trips, technical presentations at national and regional professional meetings, and publication in newsletters and various technical or trade journals.

  11. Increased oil production and reserves utilizing secondary/tertiary recovery techniques on small reservoirs in the Paradox basin, Utah. Final technical progress report, October 1--December 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Allison, M.L.

    1996-01-15

    The primary objective of this project is to enhance domestic petroleum production by demonstration and technology transfer of an advanced oil recovery technology in the Paradox basin, southeastern Utah. If this project can demonstrate technical and economic feasibility, the technique can be applied to approximately 100 additional small fields in the Paradox basin alone, and result in increased recovery of 150 to 200 million barrels of oil. This project is designed to characterize five shallow-shelf carbonate reservoirs in the Pennsylvanian (Desmoinesian) Paradox Formation and choose the best candidate for a pilot demonstration project for either a waterflood or carbon dioxide-(CO{sub 2}) flood project. The field demonstration, monitoring of field performance, and associated validation activities will take place in the Paradox basin within the Navajo Nation. The results of this project will be transferred to industry and other researchers through a petroleum extension service, creation of digital databases for distribution, technical workshops and seminars, field trips, technical presentations at national and regional professional meeting, and publication in newsletters and various technical or trade journals. Five activities continued this quarter as part of the geological and reservoir characterization of carbonate mound buildups in the Paradox basin: (1) regional facies evaluation, (2) evaluation of outcrop analogues, (3) field-scale geologic analysis, (4) reservoir analysis, and (5) technology transfer.

  12. Federal Assistance Program Quarterly Project Progress Report. Geothermal Energy Program: Information Dissemination, Public Outreach, and Technical Analysis Activities. Reporting Period: January 1 - March 31, 2001 [Final report

    Energy Technology Data Exchange (ETDEWEB)

    Lund, John W.

    2002-03-22

    The final report of the accomplishments of the geothermal energy program: information dissemination, public outreach and technical analysis activities by the project team consisting of the Geo-Heat Center, Geothermal Resources Council, Geothermal Education Office, Geothermal Energy Association and the Washington State University Energy Program.

  13. The development of coal-based technologies for Department of Defense facilities. Volume 2, Appendices. Semiannual technical progress report, September 28, 1994--March 27, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Miller, B.G.; Bartley, D.A.; Hatcher, P. [Pennsylvania State Univ., University Park, PA (United States). Energy and Fuels Research Center] [and others

    1996-10-15

    This semiannual progress report contains the following appendices: description of the 1,000 lb steam/h watertube research boiler; the Pennsylvania CGE model; Phase II, subtask 3.9 coal market analysis; the CGE model; and sector definition.

  14. Development of automated welding process for field fabrication of thick walled pressure vessels. Fourth quarter technical progress report for period ending September 30, 1979

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-01-01

    Progress in developing an automated welding process for the field fabrication of thick walled pressure vessels is reported. Plans for the demonstration facility, for nondestructive testing, and for the procurement of materials are discussed. (LCL)

  15. Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer

    Energy Technology Data Exchange (ETDEWEB)

    Kevin Whitty

    2007-06-30

    University of Utah's project entitled 'Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer' (DOE Cooperative Agreement DE-FC26-02NT41490) was developed in response to a solicitation released by the U.S. Department of Energy in December 2001, requesting proposals for projects targeted towards black liquor/biomass gasification technology support research and development. Specifically, the solicitation was seeking projects that would provide technical support for Department of Energy supported black liquor and biomass gasification demonstration projects under development at the time.

  16. Research progress on bed time and position of patients after undergoing renal puncture biopsy%肾穿刺活组织检查术后病人卧床时间及体位的研究进展

    Institute of Scientific and Technical Information of China (English)

    潘凌蕴; 吕桂兰

    2012-01-01

    对肾穿刺活组织检查术后并发症发生的时间窗、不同卧床时间对肾活检术后并发症的影响及不同体位对肾活检术后病人舒适度的影响进行综述,提出肾活检病人术后6h~8h内平卧、12h~15h后下床的安全性,应进一步探讨高危病人肾活检术后卧床及下床时间.%It reviewed the time window of postoperative complications occurrence and influence of different bed time on postoperative complications of renal biopsy, and influence of different positions on the comfort of patients after undergoing renal biopsy. It put forward the security of renal biopsy patients with the supine in 6 h~8 h after operation,and out of bed in 12 h~15 h after operation, so as to further probe into In bed and out of bed time of high - risk patients after renal biopsy.

  17. Materials Compatibility and Lubricants Research of CFC-refrigerant substitutes. Quarterly technical progress report, 1 April 1993--30 June 1993

    Energy Technology Data Exchange (ETDEWEB)

    Godwin, D.S.; Hourahan, G.C.; Szymurski, S.R.

    1993-07-01

    The Materials Compatibility and Lubricants Research (MCLR) program supports critical research to accelerate the introduction of CFC and HCFC refrigerant substitutes. The DCLR program addresses refrigerant and lubricant properties and materials compatibility. The primary elements of the work include data collection and dissemination, materials compatibility testing, and methods development. The work is guided by an Advisory Committee consisting of technical experts from the refrigeration and air-conditioning industry and government agencies. Under the current MCLR program the Air-Conditioning and Refrigeration Technology Institute, Inc., (ARTI) is contracting and managing multiple research projects and a data collection and dissemination effort. Detailed results from these projects are reported in technical reports prepared by each researcher.

  18. An Empirical Analysis on Internal and External Effects of Technical Progress in Equipment Manufacturing Industry%装备制造业技术进步内外部效应的实证分析

    Institute of Scientific and Technical Information of China (English)

    刘震; 张宏

    2016-01-01

    In the realistic context of“Made in China by 2025”and“Industrial 4.0”,this paper,based on the analysis of the do⁃mestic and international effect mechanism of technical progress in equipment manufacturing industry,empirically verifies the internal and external effects of technical progress in China’s equipment manufacturing industry with the aid of the panel and the VAR model. The study finds that:In the internal effect,the equipment manufacturing industry’s income and energy effi⁃ciency have a two-way positive impact on technical level,profit has a one-way positive impact on technical level,and employ⁃ment and technology level show a two-way negative impact;In the external effect,the equipment manufacturing industry’s FDI quality and technical level present a two-way positive impact,international division of labor and technical level present a one-way positive impact,and trade competitiveness and technical level present a two-way negative impact. Therefore,China should increase investment and improve productivity at home,and deepen the international division of labor and actively par⁃ticipate in the construction of value chain in order to improve the technical level of equipment manufacturing industry.%文章以“中国制造2025”“、工业4.0”时代来临为现实背景,在分析装备制造业技术进步的国内及国际效应作用机理的基础上,借助面板和VAR模型从实证角度验证我国装备制造业技术进步的内外部效应。研究发现,内部效应中,装备制造业收入及能耗效率指标与技术水平呈现双向正面影响,利润与技术水平为单向正面,就业与技术水平为双向负面;外部效应中,装备制造业引进外资质量与技术水平呈现双向正面影响,国际分工程度与技术水平为单向正面,贸易竞争力与技术水平为双向负面。因此为提升装备制造业技术水平,国内应加大投入,提高

  19. Research and development of methods/utilities and rules for managing cooperation for performance improvement in government offices. Second Technical progress report, September 1, 1992--January 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Kurstedt, H.A.

    1993-03-01

    Purpose is to help managers approach their responsibilities proactively, so that they can anticipate problems and take actions to alleviate or eliminate those problems. Continuous performance improvement, the philosophy behind total quality management, requires working cooperatively to do a little better each day. The most effective tools are working through a closed set of 9 methods: setting expectations, charting, defining indicators and standards, collecting and logging data, converting data to information, organizing and presenting information, reviewing status and progress, self-management, and appraising. In addition, there are 8 rules: focus on what you can do, supply physical evidence of progress, pay attention to detail, inspect (don`t expect), review progress routinely and frequently, face ``success/fail`` squarely, communicate crisply, and conduct honest, open appraisals. Scope and plans of the draft research plan (study areas) are described.

  20. Tapered bed bioreactor

    Science.gov (United States)

    Scott, Charles D.; Hancher, Charles W.

    1977-01-01

    A vertically oriented conically shaped column is used as a fluidized bed bioreactor wherein biologically catalyzed reactions are conducted in a continuous manner. The column utilizes a packing material a support having attached thereto a biologically active catalytic material.

  1. Bed Bugs FAQs

    Science.gov (United States)

    ... Bed bugs have been found in five-star hotels and resorts and their presence is not determined ... sleep. These areas include apartments, shelters, rooming houses, hotels, cruise ships, buses, trains, and dorm rooms. They ...

  2. Moving-bed sorbents

    Energy Technology Data Exchange (ETDEWEB)

    Ayala, R.E.; Gupta, R.P.; Chuck, T.

    1995-12-01

    The objective of this program is to develop mixed-metal oxide sorbent formulations that are suitable for moving-bed, high-temperature, desulfurization of coal gas. Work continues on zinc titanates formulations and Z-sorb III sorbent.

  3. Bed Bug Information Clearinghouse

    Science.gov (United States)

    Its purpose is to help states, communities, and consumers in efforts to prevent and control bed bug infestations. Currently includes only reviewed material from federal/state/local government agencies, extension services, and universities.

  4. Bed Bug Tips

    Science.gov (United States)

    How to deal with bed bugs in one printable page. Ten tips include ensuring correct insect identification, reducing clutter, understand integrated pest management, using mattress and box spring encasements, and heat treatment.

  5. Fluidized bed gasification of industrial solid recovered fuels.

    Science.gov (United States)

    Arena, Umberto; Di Gregorio, Fabrizio

    2016-04-01

    The study evaluates the technical feasibility of the fluidized bed gasification of three solid recovered fuels (SRFs), obtained as co-products of a recycling process. The SRFs were pelletized and fed to a pilot scale bubbling fluidized bed reactor, operated in gasification and co-gasification mode. The tests were carried out under conditions of thermal and chemical steady state, with a bed of olivine particles and at different values of equivalence ratio. The results provide a complete syngas characterization, in terms of its heating value and composition (including tars, particulates, and acid/basic pollutants) and of the chemical and physical characterization of bed material and entrained fines collected at the cyclone outlet. The feasibility of the fluidized bed gasification process of the different SRFs was evaluated with the support of a material and substance flow analysis, and a feedstock energy analysis. The results confirm the flexibility of fluidized bed reactor, which makes it one of the preferable technologies for the gasification of different kind of wastes, even in co-gasification mode. The fluidized bed gasification process of the tested SRFs appears technically feasible, yielding a syngas of valuable quality for energy applications in an appropriate plant configuration.

  6. Research and development of a unified approach to operations scheduling for electric power under uncertainty. Technical progress report, June 1979-June 1980

    Energy Technology Data Exchange (ETDEWEB)

    Larson, R.E.

    1980-06-01

    The objective of this study was to develop a unified approach for operations schedulng in electric power systems that explicitly takes into account sources of uncertainty present at all levels in this problem. This objective requires formulating the operations scheduling problem as a single, integrated problem, and developing solution methodologies that start from this integrated formulation and progress to subproblem solution methods that are consistent with it. Progress for the first year of the project is reported. Information is included on: problem definition; time-scale decomposition; stochastic optimization of both parallel and series reservoir systems; stochastic production simulation; maintenance scheduling and nuclear refueling; and short-term resource scheduling. (LCL)

  7. A "Fear" Studies Perspective and Critique: Analyzing English and Stengel's Progressive Study of Fear and Learning in "Education Theory." Technical Paper No. 37

    Science.gov (United States)

    Fisher, R. Michael

    2011-01-01

    The author critiques the progressive approach of two contemporary educational philosophers (English and Stengel) on the topic of fear and learning. Using a postmodern integral approach, this article examines the tendency of reductionism, individualism, and psychologism as part of a hegemonic liberalism and modernism in discourses on fear and…

  8. Materials testing and requirement for the ERDA nuclear-powered artificial heart. Technical progress report, July 15, 1975--May 30, 1976. [BIOMER and AVCOTHANE

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, J. D.; Hufferd, W. L.; Lyman, D. J.

    1976-01-01

    The two materials currently being used for the artificial heart fabrication are BIOMER and AVCOTHANE. BIOMER is a polyether urethane polymer. AVCOTHANE is a proprietary polyurethane/polydimethylsiloxane polymer blend. Research progress on the chemical degradation, mechanical strength, and blood compatibility is reported. (TFD)

  9. Silicon Germanium (SiGe) Radioisotope Thermoelectric Generator (RTG) Program for space missions. Fifteenth technical progress report, August 1-31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Whitmore, C. W.; Silverman, G.

    1980-01-01

    This program consists of the following three tasks: Multi-Hundred Watt RTG for the Galileo Probe Mission; Reestablishment of Silicon Germanium Unicouple Capability; and General Purpose Heat Source RTG for the International Solar Polar and Galileo Orbiter Missions. Details of program progress for each task, including a milestone schedule and a discussion of current problem areas (if any) are presented.

  10. Geothermal resource assessment of Mt. Hood volcano, Oregon, Phase I study. Technical progress report No. 2, October 1, 1977--March 31, 1978

    Energy Technology Data Exchange (ETDEWEB)

    Hull, D.A.

    1978-05-31

    Several phases of the Mt. Hood geothermal resource assessment project are nearing completion. Most of the field work has been completed for the geologic study, gravity survey, and water sampling portions of the project. Thermal modelling, water analyses, rock analyses and age dating, and preparation of a complete Bouguer gravity map are in progress.

  11. Design, engineering, and evaluation of refractory liners for slagging gasifiers. Second annual technical progress report, 1 October 1979-30 September 1980

    Energy Technology Data Exchange (ETDEWEB)

    Booth, G.; Firestone, R. F.; Greaves, M. J.; Hales, C.; Lamoureux, J. P.; Ledford, R. R.

    1980-10-01

    The program has been making steady progress to completion. The refractory liner test system is a much more complex design than originally proposed, but it is also safer and better able to simulate the actual coal gasification environment to which refractories will be exposed. Consequently, the data from the tests will be more reliable and the final handbook more useful for refractory liner design.

  12. Development of automated welding process for field fabrication of thick walled pressure vessels. Fourth quarter technical progress report for period ending September 28, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    Progress is reported in research aimed at optimizing an automated welding process for the field fabrication of thick-walled pressure vessels and for evaluating the welded joints. Information is included on the welding equipment, mechanical control of the process, joint design, filler wire optimization, in-process nondestructive testing of welds, and repair techniques. (LCL)

  13. Synthesis of 6-Methyl-9-n-propyldibenzothiophene-4-ol. Quarterly technical progress report No. 4, April 25--July 25, 1991

    Energy Technology Data Exchange (ETDEWEB)

    Eisenbraun, E.J.

    1991-07-25

    The material covered in this report is divided into two parts: further cyclization experiments on 1,4-diethyl-2-[(2`- methoxyphenyl)thio]benzene and its sulfone both by chemical and photochemical means, and progress toward synthesis of modified target molecule, 9-isopropyl-4-methoxy-6-methyldibenzo-thiophene. 8 refs, figs.

  14. Design, engineering, and evaluation of refractory liners for slagging gasifiers. Second annual technical progress report, 1 October 1979-30 September 1980

    Energy Technology Data Exchange (ETDEWEB)

    Booth, G.; Firestone, R. F.; Greaves, M. J.; Hales, C.; Lamoureux, J. P.; Ledford, R. R.

    1980-10-01

    The program has been making steady progress to completion. The refractory liner test system is a much more complex design than originally proposed, but it is also safer and better able to simulate the actual coal gasification environment to which refractories will be exposed. Consequently, the data from the tests will be more reliable and the final handbook more useful for refractory liner design.

  15. Evaluation and capacity building to improve precollege science and mathematics achievement in the US: 10 CFR, Part 605. Technical progress report, June--December 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-12-31

    The National Center for Improving Science Education has undertaken activities to achieve evaluation goals for DOE`s Precollege programs: develop means to determine program quality; develop means for determining the contribution of DOE precollege programs to both teacher enhancement and student achievement; provide evaluation designs and instruments and reports of program quality and impact; and strengthen both DOE`s and the Labs` capacity to do both short- and long-term planning as well as deliver effective programs and evaluation. Appendices include evaluation/technical assistance report, profiling teacher research participation and teacher development programs, teacher surveys, impact assessment design, and teacher research participation programs anecdotes for 8 labs.

  16. Biased Technical Progress and Transitions of Economic Growth Mode in China%偏向型技术进步与中国经济增长方式的转变

    Institute of Scientific and Technical Information of China (English)

    张云辉; 王天尧

    2014-01-01

    Through economic growth accounting method and combining with economic growth data since the reform and open up , this paper analyzes China's economic growth by dividing it into different stages.The study finds the current China’s economic growth mode is in the initial stage and is characterized by greater resource consumption, relying on capital investment, income inequality and so on.It is mainly caused by that China's eco-nomic growth is excessively dependent on capital-biased technical progress and it slows down the sustainable economic growth .To break through this growth resistance, we must use the technical progress matching with China's resource, namely labor-biased technical progress.Only by taking these methods, we can guide the economic growth from the initial stage to the advanced one .The specific measure is taking induced innovation in the production field .%通过经济增长核算的方法,结合改革开放以来经济增长数据将中国经济增长分阶段进行分析。研究发现,目前中国经济增长方式处在初级阶段,特点是资源消耗大、增长依靠资本投入、收入不平等。造成这种情况的主要原因是中国的经济增长过分地依赖于资本偏向型技术进步,进而导致经济的可持续增长受阻。要想突破这种增长阻力,必须利用合乎中国资源禀赋的技术进步,即劳动偏向型技术进步,才能引导经济增长方式由低级阶段转向高级阶段,具体措施是在生产领域采取诱致性创新。

  17. INVESTIGATION OF FUEL CHEMISTRY AND BED PERFORMANCE IN A FLUIDIZED BED BLACK LIQUOR STEAM REFORMER

    Energy Technology Data Exchange (ETDEWEB)

    Kevin Whitty

    2003-12-01

    The University of Utah project ''Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer'' (DOE award number DE-FC26-02NT41490) was developed in response to a solicitation for projects to provide technical support for black liquor and biomass gasification. The primary focus of the project is to provide support for a DOE-sponsored demonstration of MTCI's black liquor steam reforming technology at Georgia-Pacific's paper mill in Big Island, Virginia. A more overarching goal is to improve the understanding of phenomena that take place during low temperature black liquor gasification. This is achieved through five complementary technical tasks: (1) construction of a fluidized bed black liquor gasification test system, (2) investigation of bed performance, (3) evaluation of product gas quality, (4) black liquor conversion analysis and modeling and (5) computational modeling of the Big Island gasifier. Four experimental devices have been constructed under this project. The largest facility, which is the heart of the experimental effort, is a pressurized fluidized bed gasification test system. The system is designed to be able to reproduce conditions near the black liquor injectors in the Big Island steam reformer, so the behavior of black liquor pyrolysis and char gasification can be quantified in a representative environment. The gasification test system comprises five subsystems: steam generation and superheating, black liquor feed, fluidized bed reactor, afterburner for syngas combustion and a flue gas cooler/condenser. The three-story system is located at University of Utah's Industrial Combustion and Gasification Research Facility, and all resources there are available to support the research.

  18. Fossil-energy program. Progress report for June 1981

    Energy Technology Data Exchange (ETDEWEB)

    1981-08-01

    This report - the eighty-third of series - is a compendium of monthly progress reports for the ORNL research and development programs that are in support of the increased utilization of coal and other fossil fuel alternatives as sources of clean energy. The projects reported this month include those for coal conversion development, chemical research and development, materials technology, component development and process evaluation, technical support to major liquefaction projects, process analysis and engineering evaluations, fossil energy environmental analysis, flue gas desulfurization, coal preparation waste utilization, atmospheric fluidized bed coal combustor for cogeneration, TVA FBC demonstration plant program technical support, PFBC systems analysis, fossil fuel applications assessments, performance assurance system support for fossil energy projects, international energy technology assessment, generalized equilibrium models for liquid and gaseous fuel supplies, analyses of coal production goals, and fossil energy information center.

  19. Characteristics of American coals in relation to their conversion into clean energy fuels. Quarterly technical progress report, July--September 1975

    Energy Technology Data Exchange (ETDEWEB)

    Spackman, W.; Davis, A.; Walker, P. L.; Lovell, H. L.; Essenhigh, R. H.; Vastola, F. J.; Given, P. H.

    1975-12-01

    Twenty-one coal samples have been collected and characterized. Sixty coals have been provided to other agencies at their request. The capability of controlling coal characteristics during preparation is being developed: large variations in volatile content occur within a given raw coal but, by controlling the preparation, a uniform product with the devised specifications can be produced. Studies have begun on the suitability of various coals and cokes for use in pressurized fixed bed gasifiers. Preliminary studies are being carried out on the feasibility of applying small angle x-ray scattering to the characterization of coal chars. Reactivity profiles and parameters for chars in air are markedly dependent upon the gaseous flow system used, indicating that char reactivity is determined by partial pressure of the reacting gas. Reactivities have been maximized by keeping the heat treatment temperature as low as possible, and allowing no soak time. The minerals kaolinite, dolomite, siderite, calcite, and pyrite are found not to be catalysts for the char-air reaction at 550/sup 0/C. The addition of coal to an oil-water-air emulsion considerably increases the heat flux from the flame to the water tubes during combustion. (auth)

  20. A charge distribution analysis instrument for catalysis and material science applications. Third quarterly technical progress report, April 1, 1994--June 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Freund, F.

    1994-08-05

    Key component in the CDA instrument is the differential capacitive force sensor. The CDA instrument has four basic components: OEM analytical balance, flexure point and capacitor plates, gas confinement tower and high-voltage bias electrodes, and the furnace. Phyton is in position to purchase an OEM analytical balance; negotations are underway for obtaining the feedback control circuitry for the differential capacitive force sensor. Progress with the differential capacitive force sensor is reviewed.

  1. GPHS-RTGs in support of the Cassini Mission. Semi annual technical progress report, 28 March 1994--25 September 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-10-20

    The progress on the radioisotope generators and ancillary activities is described. This report is organized by program task as follows: spacecraft integration and liaison; engineering support; safety; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; design, reviews, and mission applications; project management, quality assurance and reliability, contract changes, non-capital CAGO acquisition, and CAGO maintenance; contractor acquired government owned property (CAGO) acquisition.

  2. Circulating fluidized bed biological reactor for nutrients removal

    Institute of Scientific and Technical Information of China (English)

    Yubo CUI; Hongbo LIU; Chunxue BAI

    2008-01-01

    A new biological nitrogen removal process, which is named herein "The circulating fluidized bed bio-reactor (CFBBR)", was developed for simultaneous removal of nitrogen and organic matter. This process was composed of an anaerobic bed (Riser), aerobic bed (Downer) and connecting device. Influent and nitrified liquid from the aerobic bed enters the anaerobic bed from the bottom of the anaerobic bed, completing the removal of nitrogen and organic matter. The system performance under the conditions of different inflow loadings and nitrified liquid recirculation rates ranging from 200% to 600% was examined. From a technical and economic point of view, the optimum nitrified liquid recirculation rate was 400%. With a shortest total retention time of 2.5 h (0.8 h in the anaerobic bed and 1.5 h in the aerobic bed) and a nitrified liquid recir-culation rate of 400% based on the intluent flow rate, the average removal efficiencies of total nitrogen (TN) and sol-uble chemical oxygen demand (SCOD) were found to be 88% and 95%, respectively. The average effluent concentra-tions of TN and SCOD were 3.5 mg/L and 16 mg/L, respectively. The volatile suspended solid (VSS) concentra-tion, nitrification rate and denitrification rate in the system were less than 1.0 g/L, 0.026-0.1 g NH4+-N/g VSS.d, and 0.016-0.074 g NOx--N/g VSS.d, respectively.

  3. New Metallization Technique Suitable for 6-MW Pilot Production of Efficient Multicrystalline Solar Cells Using Upgraded Metallurgical Silicon: Final Technical Progress Report, December 17, 2007 -- June 16, 2009

    Energy Technology Data Exchange (ETDEWEB)

    Ounadjela, K.; Blosse, A.

    2010-08-01

    This report describes CaliSolar's work as a Photovoltaic Technology Incubator awardee within the U.S. Department of Energy's Solar Energy Technologies Program. The term of this subcontract with the National Renewable Energy Laboratory was two years. During this time, CaliSolar evolved from a handful of employees to over 100 scientists, engineers, technicians, and operators. On the technical side, the company transitioned from a proof-of-concept through pilot-scale to large-scale industrial production. A fully automated 60-megawatt manufacturing line was commissioned in Sunnyvale, California. The facility converts upgraded metallurgical-grade silicon feedstock to ingots, wafers, and high-efficiency multicrystalline solar cells.

  4. Development and testing of commercial-scale, coal-fired combustion systems, Phase 3. Technical progress report, October 1990--December 1990

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-31

    The US Department of Energy`s Pittsburgh Energy Technology Center (PETC) is actively pursuing the development and testing of coal-fired combustion systems for residential, commercial, and industrial market sectors. In response, MTCI initiated the development of a new combustor technology based on the principle of pulse combustion under the sponsorship of PETC (Contract No. AC22-83PC60419). The initial pulse combustor development program was conducted in three phases (MTCI, Development of a Pulsed Coal Combustor Fired with CWM, Phase III Final Report, DOE Contract No. AC22-83PC60419, November 1986). Phase I included a review of the prior art in the area of pulse combustion and the development of pulse combustor design concepts. It led to the conclusion that pulse combustors offer technical and base-of-operation advantages over conventional burners and also indicated favorable economics for replacement of oil- and gas-fired equipment.

  5. Advanced development of fine coal desulfurization and recovery technology. Quarterly technical progress report, October 1, 1976--December 31, 1976. [53 references

    Energy Technology Data Exchange (ETDEWEB)

    Fisher, R.W.; Wheelock, T.D.

    1977-02-01

    The improvement and technical development of promising methods for desulfurizing and recovering fine coal underway includes froth flotation, selective oil agglomeration, pelletization, and a chemical desulfurization process which involves leaching fine coal with a hot dilute solution of sodium carbonate containing dissolved oxygen under pressure. A preliminary assessment of the state of the art and review of the technical literature has been made. Equipment and apparatus have been assembled for small-scale laboratory experiments in froth flotation, oil agglomeration and chemical desulfurization. Preliminary froth flotation tests have been carried out on an Iowa coal to establish baseline data. Quite unexpectedly these tests indicated that aluminum nitrate may be an activator for coal because it served to increase the recovery of coal. Several potential flotation depressants for pyrite have been screened by measurement at the zeta potential and floatability of pyrite or coal in aqueous suspensions containing the potential depressants. The following reagents show some promise as pyrite depressants: ferric chloride, sodium cyanide, ammonium thiocyanate, and the disodium salt of ethylenediaminetetraacetic acid. Preliminary plans have been prepared for a continuous flow bench-scale system to demonstrate the process. This system will include equipment for grinding and pretreating the coal as well as equipment for demonstrating froth flotation, selective oil agglomeration and pelletization. An investigation of coal microstructure as it relates to coal beneficiation methods has also been initiated. The distribution of various forms of pyrite by size and crystal structure has been determined for two cannel samples of coal through application of scanning electron microscope techniques.

  6. Pulsed atmospheric fluidized bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    1989-11-01

    In order to verify the technical feasibility of the MTCI Pulsed Atmospheric Fluidized Bed Combustor technology, a laboratory-scale system was designed, built and tested. Important aspects of the operational and performance parameters of the system were established experimentally. A considerable amount of the effort was invested in the initial task of constructing an AFBC that would represent a reasonable baseline against which the performance of the PAFBC could be compared. A summary comparison of the performance and emissions data from the MTCI 2 ft {times} 2 ft facility (AFBC and PAFBC modes) with those from conventional BFBC (taller freeboard and recycle operation) and circulating fluidized bed combustion (CFBC) units is given in Table ES-1. The comparison is for typical high-volatile bituminous coals and sorbents of average reactivity. The values indicated for BFBC and CFBC were based on published information. The AFBC unit that was designed to act as a baseline for the comparison was indeed representative of the larger units even at the smaller scale for which it was designed. The PAFBC mode exhibited superior performance in relation to the AFBC mode. The higher combustion efficiency translates into reduced coal consumption and lower system operating cost; the improvement in sulfur capture implies less sorbent requirement and waste generation and in turn lower operating cost; lower NO{sub x} and CO emissions mean ease of site permitting; and greater steam-generation rate translates into less heat exchange surface area and reduced capital cost. Also, the PAFBC performance generally surpasses those of conventional BFBC, is comparable to CFBC in combustion and NO{sub x} emissions, and is better than CFBC in sulfur capture and CO emissions even at the scaled-down size used for the experimental feasibility tests.

  7. Innovative Clean Coal Technology (ICCT): 180 MW demonstration of advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Technical progress report, second quarter 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-11-25

    This quarterly report discusses the technical progress of a US Department of Energy (DOE) Innovative Clean Coal Technology (ICCT) Project demonstrating advanced tangentially-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from a coal-fired boiler. The project is being conducted at Gulf Power Company`s Plant Lansing Smith Unit 2 located near Panama City, Florida. The primary objective of this demonstration is to determine the long-term effects of commercially available tangentially-fired low NO{sub x} combustion technologies on NO{sub x} emissions and boiler performance. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project. The stepwise approach that is being used to evaluate the NO{sub x} control technologies requires three plant outages to successively install the test instrumentation and the different levels of the low NO{sub x} concentric firing system (LNCFS). Following each outage, a series of four groups of tests are performed. These are (1) diagnostic, (2) performance, (3) long-term, and (4) verification. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency. This technical progress report presents the LNCFS Level I short-term data collected during this quarter. In addition, a comparison of all the long-term emissions data that have been collected to date is included.

  8. The economical production of alcohol fuels from coal-derived synthesis gas. Quarterly technical progress report No. 19, April 1, 1996--June 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-07-01

    The objective of Task I is to prepare and evaluate catalysts and to develop efficient reactor systems for the selective conversion of hydrogen-lean synthesis gas to alcohol fuel extenders and octane enhancers. In Task 1, during this reporting period, we encountered and solved a problem in the analysis of the reaction products containing a small amount of heavy components. Subsequently, we continued with the major thrusts of the program. We analyzed the results from our preliminary studies on the packed-bed membrane reactor using the BASF methanol synthesis catalyst. We developed a quantitative model to describe the performance of the reactor. The effect of varying permeances and the effect of catalyst aging are being incorporated into the model. Secondly, we resumed our more- detailed parametric studies on selected non-sulfide Mo-based catalysts. Finally, we continue with the analysis of data from the kinetic study of a sulfided carbon-supported potassium-doped molybdenum-cobalt catalyst in the Rotoberty reactor. We have completed catalyst screening at UCC. The complete characterization of selected catalysts has been started. In Task 2, the fuel blends of alcohol and unleaded test gas 96 (UTG 96) have been made and tests have been completed. The testing includes knock resistance tests and emissions tests. Emissions tests were conducted when the engine was optimized for the particular blend being tested (i.e. where the engine produced the most power when running on the blend in question). The data shows that the presence of alcohol in the fuel increases the fuel`s ability to resist knock. Because of this, when the engine was optimized for use with alcohol blends, the engine produced more power and lower emission rates.

  9. Thorium utilization program. Quarterly progress report for the period ending November 30, 1975. [Fuel element crushing, solids handling, fluidized bed combustion, aqueous separations, solvent extraction, systems design and drafting, alternative head-end reprocessing, and fuel recycle systems analysis

    Energy Technology Data Exchange (ETDEWEB)

    1975-12-31

    The development program for HTGR fuel reprocessing continues to emphasize the design and construction of a prototype head-end line. Design work on the multistage crushing system, the primary and secondary fluidized bed burners, the pneumatic transfer systems, and the ancillary fixtures for semiremote assembly and disassembly is essentially complete. Fabrication and receipt of all major components is under way, and auxiliary instrumentation and support systems are being installed. Studies of flow characteristics of granular solids in pneumatic transfer systems are continuing and data are being collected for use in design of systems for solids handling. Experimental work on the 20-cm primary fluidized bed burner verified the fines recycle operating mode in runs of greater than 24 hr. Twelve leaching runs were performed during the quarter using crushed, burned-back TRISO coated ThC/sub 2/ particles and burned-back BISO coated sol gel ThO/sub 2/ particles to examine the effect of varying the Thorex-to-thoria ratio to give product solutions ranging from 0.25M to 1M in thorium. Only minor effects were observed and reference values for facility operations were specified. Two-stage leaching runs with burned-back ThC/sub 2/ indicate there are no measurable differences in total dissolution time as compared to single-stage leaching. Bench-scale tests on oxidation of HTGR fuel boron carbide at 900/sup 0/C indicates that most if not all of the carbide will be converted to boron oxide in the fluidized bed burner. Eight solvent extraction runs were completed during the quarter. These runs represented the first cycle and second uranium cycle of the acid-Thorex flowsheet. A detailed calculation of spent fuel compositions by fuel block and particle type is being performed for better definition of process streams in a fuel reprocessing facility.

  10. 高温气冷堆球床等效导热系数实验研究进展%Progress in Pebble Bed Heat Transfer Test Facility of High Temperature Gas-cooled Reactor

    Institute of Scientific and Technical Information of China (English)

    任成; 杨星团; 李聪新; 孙艳飞

    2013-01-01

    Pebble bed effective thermal conductivity of the reactor core is a vital parameter which directly affects the maximum temperature of fuel and the temperature distribution of reactor core in high temperature gas-cooled reactor and plays a dominant role in afterheat removal. The experimental research of pebble bed effective thermal conductivity is helpful for improving the reactor analytical program, increasing the power of single reactor and the safe analysis of projects. The experiments and results of pebble bed effective thermal conductivity measurement at home and abroad are reviewed. The develop direction is also discussed.%堆芯球床等效导热系数是直接影响高温气冷堆燃料最高温度和堆芯温度分布的关键参数;在余热导出过程中起主导作用.开展球床等效导热系数的实验研究对于反应堆分析程序的完善、研究提高高温气冷堆单堆功率的可能性、以及工程的安全分析具有重要的意义.综述了国内外球床等效导热系数测量的研究现状,给出了清华大学HTR-PM三维堆芯球床等效导热系数测量实验最新成果,总结了各国实验的研究手段,对研究方向进行了讨论.

  11. 1993 Annual progress report for subsidiary agreement No. 2 (1991--1996) between AECL and US/DOE for a radioactive waste management technical co-operative program

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    A coordinated research program on radioactive waste disposal is being carried out by the Atomic Energy of Canada Limited and the US Department of Energy. This annual report describes progress in the following eight studies: Fundamental materials investigations; In-situ stress determination; Development of a spent fuel dissolution model; Large block tracer test--Experimental testing of retardation models; Laboratory and field tests of in-situ hydrochemical tools; Cigar Lake--Analogue study, actinide and fission product geochemistry; Performance assessment technology exchange; and Development of multiple-well hydraulic test and field tracer test methods.

  12. Characterization of open-cycle coal-fired MHD generators. 14th/15th quarterly technical progress report, February 1-July 31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Wormhoudt, J.; Yousefian, V.; Weinberg, M.; Kolb, C.; Martinez-Sanchez, M.; Cheng, W.; Bien, F.; Dvore, D.; Unkel, W.; Stewart, G.

    1980-09-01

    The successful design of full-scale, open-cycle, coal-fired MHD generators for baseload electrical production requires a detailed understanding of the plasma chemical and plasma dynamic characteristics of anticipated combustor and channel fluids. Progress in efforts to model the efficiency of an open-cycle, coal-fired MHD channel based on the characterization of the channel flow as well as laboratory experiments to validate the modeling effort as detailed. In addition, studies related to understanding arcing phenomena in the vicinity of an anode are reported.

  13. Preliminary study of the behavioral and biological effects of high intensity 60 HZ electric fields. Interim technical progress report No. 4

    Energy Technology Data Exchange (ETDEWEB)

    Feldstone, C.; Spiegel, R.J.; Winters, W.; Polonis, J.J.

    1980-03-01

    Progress is reported in studies of the effects of high intensity 60 Hz electric fields on baboon behavior - both individual performance (operant conditioning) and natural (social) behavior. The result of the study should be either a clear indication of the electric field intensity which produces deleterious effects in the baboon or an indication that the highest field intensity of practical interest (analogous to the highest intensity that can be encountered by man under power lines) produces no deleterious effects. The generalization of results to man will be futher aided by the development of models relating the physical effects of electric fields on man to the physical effects on the baboon. (LCL)

  14. Bed bug deterrence

    Directory of Open Access Journals (Sweden)

    Haynes Kenneth F

    2010-09-01

    Full Text Available Abstract A recent study in BMC Biology has determined that the immature stage of the bed bug (the nymph signals its reproductive status to adult males using pheromones and thus avoids the trauma associated with copulation in this species. The success of this nymphal strategy of deterrence is instructive. Against the background of increasing problems with bed bugs, this research raises the question whether pheromones might be used to control them. See research article http://www.biomedcentral.com/1741-7007/8/121

  15. in Spouted Bed

    Directory of Open Access Journals (Sweden)

    Bronislaw Buczek

    2013-01-01

    Full Text Available Samples of active coke, fresh and spent after cleaning flue gases from communal waste incinerators, were investigated. The outer layers of both coke particles were separately removed by comminution in a spouted bed. The samples of both active cokes were analysed by means of densities, mercury porosimetry, and adsorption technique. Remaining cores were examined to determine the degree of consumption of coke by the sorption of hazardous emissions (SO2, HCl, and heavy metals through its bed. Differences in contamination levels within the porous structure of the particles were estimated. The study demonstrated the effectiveness of commercial active coke in the cleaning of flue gases.

  16. Treatment of N-Nitrosodimethylamine (NDMA) in Groundwater Using a Fluidized Bed Bioreactor

    Science.gov (United States)

    2014-01-01

    FINAL REPORT Treatment of N-Nitrosodimethylamine (NDMA) in Groundwater Using a Fluidized Bed Bioreactor ESTCP Project ER-200829...08-C-0021 USING A FLUIDIZED BED BIOREACTOR 5b. GRANT NUMBER NA 5c. PROGRAM ELEMENT NUMBER NA 6. AUTHOR(St 5d. PROJECT NUMBER Hatzinger, Paul B...14.ABSTRACT This ESTCP demonstration evaluated the technical effectiveness and cost of a fluidized bed bioreactor (FBR) for treating N-ni

  17. The Safety of Hospital Beds

    Science.gov (United States)

    Gervais, Pierre; Pooler, Charlotte; Merryweather, Andrew; Doig, Alexa K.; Bloswick, Donald

    2015-01-01

    To explore the safety of the standard and the low hospital bed, we report on a microanalysis of 15 patients’ ability to ingress, move about the bed, and egress. The 15 participants were purposefully selected with various disabilities. Bed conditions were randomized with side rails up or down and one low bed with side rails down. We explored the patients’ use of the side rails, bed height, ability to lift their legs onto the mattress, and ability to turn, egress, and walk back to the chair. The standard bed was too high for some participants, both for ingress and egress. Side rails were used by most participants when entering, turning in bed, and exiting. We recommend that side rails be reconsidered as a means to facilitate in-bed movement, ingress, and egress. Furthermore, single deck height settings for all patients are not optimal. Low beds as a safety measure must be re-evaluated. PMID:28462302

  18. Environmental and economic assessment of discharges from Gulf of Mexico Region Oil and Gas Operations. Quarterly technical progress report, January 1, 1994--March 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Gettleson, D.A.

    1994-04-21

    The primary objectives of the project are to increase the base of scientific knowledge concerning (1) the fate and environmental effects of organics, trace metals, and NORM in water, sediment, and biota near several offshore oil and gas facilities; (2) the characteristics of produced water and produced sand discharges as they pertain to organics, trace metals, and NORM variably found in association with the discharges; (3) the recovery of four terminated produced water discharge sites located in wetland and high-energy open bay sites of coastal Louisiana and Texas; (4) the economic and energy supply impacts of existing and anticipated federal and state offshore and coastal discharge regulations; and (5) the catch, consumption and human use patterns of seafood species collected from coastal and offshore waters. The products of the effort will be a series of technical reports detailing the study procedures, results, and conclusions which contribute to the transfer of technology to the scientific community, petroleum industry, and state and federal programs.

  19. Geothermal space/water heating for Mammoth Lakes Village, California. Quarterly technical progress report, 13 December 1976-12 March 1977

    Energy Technology Data Exchange (ETDEWEB)

    Sims, A.V.; Racine, W.C.

    1977-01-01

    During the second three months of this feasibility study to determine the technical, economic and environmental feasibility of heating Mammoth Lakes Village, California using geothermal energy, the following work was accomplished. A saturation survey of the number and types of space and water heaters currently in use in the Village was completed. Electric energy and ambient temperature metering equipment was installed. Peak heating demand for Mammoth Lakes was estimated for the years 1985, 1990 and 2000. Buildings were selected which are considered typical of Mammoth Lakes in terms of their heating systems to be used in estimating the cost of installing hydronic heating systems in Mammoth. Block diagrams and an order of magnitude cost comparison were prepared for high-temperature and low-temperature geothermal district heating systems. Models depicting a geothermal district heating system and a geothermal-electric power plant were designed, built and delivered to ERDA in Washington. Local input to the feasibility study was obtained from representatives of the State of California Departments of Transportation and Fish and Game, US Forest Service, and Mono County Planning Department.

  20. Undergraduate technical skills training guided by student tutors – Analysis of tutors' attitudes, tutees' acceptance and learning progress in an innovative teaching model

    Directory of Open Access Journals (Sweden)

    Jünger Jana

    2008-04-01

    Full Text Available Abstract Background Skills labs provide a sheltered learning environment. As close supervision and individual feedback were proven to be important in ensuring effective skills training, we implemented a cross-year peer tutor system in our skills lab of internal medicine that allowed intense training sessions with small learning groups (3–4 students taught by one student tutor. Methods The expectations, experiences and criticisms of peer tutors regarding the tutor system for undergraduate skills lab training were investigated in the context of a focus group. In addition, tutees' acceptance of this learning model and of their student tutors was evaluated by means of a pre/post web-based survey. Results 14 voluntary senior students were intensely prepared by consultants for their peer tutor activity. 127 students participated in the project, 66.9% of which responded to the web-based survey (23 topics with help of 6-point Likert scale + free comments. Acceptance was very high (5.69 ± 0.07, mean ± SEM, and self-confidence ratings increased significantly after the intervention for each of the trained skills (average 1.96 ± 0.08, all p Conclusion This study demonstrates that peer teaching in undergraduate technical clinical skills training is feasible and widely accepted among tutees, provided that the tutors receive sufficient training and supervision.

  1. MULTISTAGE FLUIDIZED BED REACTOR

    Science.gov (United States)

    Jonke, A.A.; Graae, J.E.A.; Levitz, N.M.

    1959-11-01

    A multistage fluidized bed reactor is described in which each of a number of stages is arranged with respect to an associated baffle so that a fluidizing gas flows upward and a granular solid downward through the stages and baffles, whereas the granular solid stopsflowing downward when the flow of fluidizing gas is shut off.

  2. Fluidized bed combustion chamber

    Energy Technology Data Exchange (ETDEWEB)

    Kullendorff, A.; Wikner, J.

    1985-03-25

    The chamber is confined in a pressure vessel. The lower part of the chamber has tilted parallel gutters up to the height of the fluidized bed. The slope of the gutter walls is 5 degrees-15 degrees and the top area of the gutters is 1.3 to 3 times larger than their bottom.

  3. Bed Bug Myths

    Science.gov (United States)

    Learn the truth about bed bugs, such as how easy they are to see with the naked eye, their preferred habitat, whether they transmit diseases, their public health effects, and whether pesticides are the best way to deal with an infestation.

  4. Surviving Bed Rest

    Science.gov (United States)

    ... your pregnancy — and your bed rest start a family tree that you can share with your child someday firm up your baby-name choices; use books and websites for ideas organize photo albums read anything — ... people (friends and family) whom you know will probably give gifts build ...

  5. Development of innovative techniques and principles that may be used as models to improve plant performance. Technical progress report, February 1, 1991--January 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Hanna, W.W.; Burton, G.W.

    1991-09-01

    Methods and techniques for transferring germplasm from wild to cultivated species are being developed. The transferred germplasm is being shown to be valuable in plant breeding and in cultivar development. Forty cytoplasms from the wild grassy subspecies monodii (primary gene pool) of Pennisetum glaucum are being tested for cytoplasmic effects on morphological characteristics and forage yield. A`-genome chromosomes from P. purpureum (secondary gene pool) have been transferred to cultivated pearl millet. The A`-chromosome derived lines have been developed into excellent male pollinator lines to produce a new high quality, high yielding grain hybrid for the US. Significant progress is being made in transferring the genes controlling apomixis (to produce true-breeding hybrids) from the tertiary gene pool to cultivated pearl millet. Backcross-4 plants are more pearl millet-like and reproduce by apomixis. New genome combinations have been produced in the apomixis genes transfer program which demonstrate the impact of apomixis on speciation and evolution.

  6. Engineering support services for the DOE/GRI coal-gasification research program. Quarterly technical progress report, October-December 1981

    Energy Technology Data Exchange (ETDEWEB)

    Bostwick, L.E.; Ethridge, T.R.; Starr, D.W.; Shah, K.V.; Hubbard, D.A.; Koneru, P.B.; Smith, M.R.; Ward, W.E.; Wong, E.W.; Zeis, L.A.

    1982-02-01

    Kellogg continued to actively monitor operations at BI-GAS Westinghouse and IGT (for peat gasification). Pilot plant/PDU testing which was monitored and reported includes Westinghouse PDU tests TP-030-3 and TP-031-3 and CFSF test TP-M003-1; Peatgas Pilot Plant test No. 4; and single-stage peat gasification PDU tests BF-22 and BF-23. Kellogg personnel briefed the GRI Project Advisors on current tasks and a DOE representative on peat-related work. The report on the Hygas Data Base Evaluation was approved for issue. Progress was made toward finalizing the report on the Peatgas Data Base Evaluation and the Descriptive Brochure for the DOE/GRI Joint Program. Work on the evaluation of the data base for single-stage peat gasification continued. Review of the Hygas final report was completed.

  7. Application of railgun principle to high-velocity hydrogen pellet injection for magnetic fusion reactor refueling. Technical progress report, [July 16, 1990--August 16, 1991

    Energy Technology Data Exchange (ETDEWEB)

    Kim, K.

    1991-08-01

    This report contains three documents describing the progress made by the University of Illinois electromagnetic railgun program sponsored by the Office of Fusion Energy of the United States Department of Energy during the period from July 16, 1990 to August 16, 1991. The first document contains a brief summary of the tasks initiated, continued, or completed, the status of major tasks, and the research effort distribution, estimated and actual, during the period. The second document contains a description of the work performed on time resolved laser interferometric density measurement of the railgun plasma-arc armature. The third document is an account of research on the spectroscopic measurement of the electron density and temperature of the railgun plasma arc.

  8. Application of integrated reservoir management and reservoir characterization to optimize infill drilling. Quarterly technical progress report, June 13--September 12, 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The eighteen 10-acre infill wells which were drilled as part of the field demonstration portion of the project are all currently in service with no operational problems. These wells consist of fourteen producing wells and four injection wells. The producing wells are currently producing a total of approximately 500 bopd, down from a peak rate of 900 bopd. Unit production is currently averaging approximately 2,800 bopd, 12,000 bwpd and 17,000 bwipd. The paper describes progress on core analysis, gas-oil/oil-gas permeability tests, water-oil/oil-water permeability tests, water-gas permeability tests, electrical resistivity measurements, capillary pressure tests, reservoir surveillance, and paleontologic analysis.

  9. Application of integrated reservoir management and reservoir characterization to optimize infill drilling. Quarterly technical progress report, March 13--June 12, 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The eighteen 10-acre infill wells which were drilled as part of the field demonstration portion of the project are all currently in service with no operational problems. These wells consist of fourteen producing wells and four injection wells. The producing wells are currently producing a total of approximately 650 bopd, down from a peak rate of 900 bopd. Unit production is currently averaging approximately 3,000 bopd, 12,000 bwpd and 18,000 bwipd. The paper describes progress in core analysis, reservoir surveillance, well stimulation, validation of reservoir characterization (includes thin section analyses, depositional environments, and paleontologic analysis), material balance decline curve analysis, and validation of reservoir simulation (includes geostatistical and deterministic).

  10. Identification and validation of heavy metal and radionuclide hyperaccumulating terrestrial plant species, Quarterly technical progress report, December 20, 1995--March 20, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Kochian, L.; Brady, D.; Last, M.; Ebbs, S.

    1995-12-01

    Although the period covered by this progress report began on December 20, 1994, which was the date that DOE approved the Interagency Agreement, the agreement was not approved by USDA until January 9, 1995 and the first scientists working on the project were not hired until February 1, 1995. The first goal of the research supported by the Interagency Agreement is to use hydroponic techniques to identify plant species and genotypes with potential for heavy metal hyperaccumulation for planting on a test site at Silverbow Creek and for radionuclide ({sup 90}Sr and {sup 137}Cs) accumulation on a test site at INEL, Idaho, later this year. The second goal of this research is to identify soil amendment procedures that will enhance the bioavailability of heavy metals and radionuclides in the soil without increasing the movement of the contaminants of concern (COC`s) into the groundwater. Our initial research covered in this report focuses on the first goal.

  11. Process feasibility study in support of silicon material, Task I. Quarterly technical progress report (XVIII), December 1, 1979-February 29, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Yaws, C.L.; Li, K.Y.

    1980-03-01

    Analyses of process system properties were continued for important chemical materials involved in the several processes under consideration for semiconductor and solar cell grade silicon production. Major activities were devoted to physical, thermodynamic and transport property data for silicon. Property data are reported for vapor pressure heat of vaporization, heat of sublimation, liquid heat capacity and solid heat capacity as a function of temperature to permit rapid usage in engineering. Chemical engineering analysis of the HSC process (Hemlock Semiconductor Corporation) for production of silicon was initiated. The process is based on hydrogen reduction of dichlorosilane (DCS) to produce the polysilicon. The chemical vapor deposition reaction for DCS is faster in rate than the conventional process route which utilizes trichlorosilane (TCS) as the silicon raw material. Status and progress are reported for primary activities of base case conditions (30%), reaction chemistry (25%) and process flow diagram (20%). Discussions with HSC and construction of a process flow diagram are in progress. Preliminary economic analysis of the BCL process (case B) was completed. Cost analysis results are presented based on a preliminary process design of a plant to produce 1000 metric tons/year of silicon. Fixed capital investment for the plant is $14.35 million (1980 dollars) and product cost without profit is 11.08 $/kg of silicon (1980 dollars). Cost sensitivity analysis indicate that the product cost is influenced most by plant investment and least by labor. For profitability, a sales price of 14 $/kg (1980 dollars) gives a 14% DCF rate of return on investment after taxes.

  12. Engineering development of advanced coal-fired low-emission boiler systems. Technical progress report No. 10, January 1995--March 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-17

    The project is on schedule and under budget. The current status is shown in the Milestone Schedule Report included as Appendix A. All Project Plans were updated based on the revised finding level authorized for FY95 and anticipated for FY96. Technology Transfer activities included {open_quotes}supplying{close_quotes} three executives and several team members to the LEBS Workshop, delivering a technical paper at a conference, and working on a Combustion 2000 Session for another conference. ABBES and CeraMem reached agreement concerning Task 7 work, including ownership and disposition of project-purchased equipment to be used during Task 7 and also during Task 11. A test plan was prepared. Task 7 activities for the Low-NO{sub x} Firing System included computational modeling of the firing arrangement. Reasonable comparisons to experimental data previously obtained in the Boiler Simulation Facility were achieved. A kinetic evaluation for both baseline and low NO{sub x} firing arrangements was also performed, with results indicating that the final reducing zone within the main windbox has a dominant effect on NO{sub x} reduction, with higher temperatures being more favorable for lower NO{sub x}. A week of combustion testing was completed in the Fundamental Scale Burner Facility to examine the impact of integrated fuel staging (NO{sub x} reduction via the reburn mechanism), and to explore preliminary vertical staging concepts within the main windbox region. Preliminary results from this testing demonstrated the potential of vertical air staging within the main windbox to augment overfire air. Testing was performed to quantify the coal size distribution and power requirements for one (1) conventional static and four (4) dynamic classifier designs. Results from this testing show the dynamic classifier capable of producing finer grinds of coal at lower relative power requirements.

  13. Undergraduate technical skills training guided by student tutors--analysis of tutors' attitudes, tutees' acceptance and learning progress in an innovative teaching model.

    Science.gov (United States)

    Weyrich, Peter; Schrauth, Markus; Kraus, Bernd; Habermehl, Daniel; Netzhammer, Nicolai; Zipfel, Stephan; Jünger, Jana; Riessen, Reimer; Nikendei, Christoph

    2008-04-09

    Skills labs provide a sheltered learning environment. As close supervision and individual feedback were proven to be important in ensuring effective skills training, we implemented a cross-year peer tutor system in our skills lab of internal medicine that allowed intense training sessions with small learning groups (3-4 students) taught by one student tutor. The expectations, experiences and criticisms of peer tutors regarding the tutor system for undergraduate skills lab training were investigated in the context of a focus group. In addition, tutees' acceptance of this learning model and of their student tutors was evaluated by means of a pre/post web-based survey. 14 voluntary senior students were intensely prepared by consultants for their peer tutor activity. 127 students participated in the project, 66.9% of which responded to the web-based survey (23 topics with help of 6-point Likert scale + free comments). Acceptance was very high (5.69 +/- 0.07, mean +/- SEM), and self-confidence ratings increased significantly after the intervention for each of the trained skills (average 1.96 +/- 0.08, all p teaching model to be sufficient, and a mere 1% expressed the wish for skills training to be provided by faculty staff only. Focus group analyses with tutors revealed 18 different topics, including profit in personal knowledge and personal satisfaction through teaching activities. The ratio of 1:4 tutor/tutees was regarded to be very beneficial for effective feedback, and the personalized online evaluation by tutees to be a strong motivator and helpful for further improvements. The tutors ascribed great importance to the continuous availability of a contact doctor in case of uncertainties. This study demonstrates that peer teaching in undergraduate technical clinical skills training is feasible and widely accepted among tutees, provided that the tutors receive sufficient training and supervision.

  14. Development & testing of industrial scale, coal fired combustion system, phase 3. Eighth quarterly technical progress report, 1 October, 1993--31 December, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Zauderer, B.

    1994-01-31

    The primary objective of the present Phase 3 effort is to perform the final testing at a 20 MMBtu/hr commercial scale of an air cooled, slagging coal combustor for application to industrial steam boilers and power plants. The focus of the test effort will be on combustor durability, automatic control of the combustor`s operation, and optimum environmental control of emissions inside the combustor. In connection with the latter, the goal is to achieve 0.4 lb/MMBtu of SO{sub 2} emissions, 0.2 lb/MMBtu of NO{sub x} emissions, and 0.02 lb particulates/MMBtu. Meeting the particulate goal will require the use of a baghouse or electrostatic precipitator to augment the nominal slag retention in the combustor. The NO{sub x} emission goal will require a modest improvement over maximum reduction achieved to date in the combustor to a level of 0.26 lb/MMBtu. To reach the SO{sub 2} emissions goal may require a combination of sorbent injection inside the combustor and sorbent injection inside the boiler, especially in high (>3.5%) sulfur coals. Prior to the initiation of the project, SO{sub 2} levels as low as 0.6 lb/MMBtu, equal to 81% reduction in 2% sulfur coals, were measured with boiler injection of calcium hydrate. The final objective is to define suitable commercial power or steam generating systems to which the use of the air cooled combustor offers significant technical and economic benefits. In implementing this objective both simple steam generation and combined gas turbine-steam generation systems will be considered.

  15. Bathing a patient in bed

    Science.gov (United States)

    ... medlineplus.gov/ency/patientinstructions/000427.htm Bathing a patient in bed To use the sharing features on this page, please enable JavaScript. Some patients cannot safely leave their beds to bathe. For ...

  16. VA National Bed Control System

    Data.gov (United States)

    Department of Veterans Affairs — The VA National Bed Control System records the levels of operating, unavailable and authorized beds at each VAMC, and it tracks requests for changes in these levels....

  17. Fluidized bed combustion of pesticide-manufacture liquid wastes

    Directory of Open Access Journals (Sweden)

    SAŠA MILETIĆ

    2010-04-01

    Full Text Available Industrial liquid wastes can be in the form of solutions, suspensions, sludges, scums or waste oil and have organic properties. The objective of this work was to demonstrate the technical feasibility of a fluidized bed as a clean technology for burning liquid waste from a pesticide production plant. The combustion of liquid waste mixtures, obtained from realistic samples, was investigated in a pilot scale fluidized bed with quartz sand particles of 0.63–1.25 mm in diameter and 2610 kg/m3 in density at 800–950 °C. To ensure complete combustion of liquid waste and additional fuel, the combustion chamber was supplied with excess air and the U/UmF (at ambient temperature was in between 1.1 and 2.3. In the fluidized bed chamber, liquid waste, additional liquid fuel and air can be brought into intense contact sufficient to permit combustion in bed without backfire problems. The experimental results show that the fluidized bed furnace offers excellent thermal uniformity and temperature control. The results of the combustion tests showed that degradation of liquid wastes can be successfully realized in a fluidized bed with no harmful gaseous emissions by ensuring that the temperatures of both the bed and the freeboard are not lower than 900 °C.

  18. Oil shale, tar sand, coal research, advanced exploratory process technology, jointly sponsored research. Quarterly technical progress report, April--June 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    Progress made in five areas of research is described briefly. The subtask in oil shale research is on oil shale process studies. For tar sand the subtask reported is on process development. Coal research includes the following subtasks: Coal combustion; integrated coal processing concepts; and solid waste management. Advanced exploratory process technology includes the following: Advanced process concepts; advanced mitigation concepts; oil and gas technology. Jointly sponsored research includes: Organic and inorganic hazardous waste stabilization; CROW{sup TM} field demonstration with Bell Lumber and Pole; development and validation of a standard test method for sequential batch extraction fluid; operation and evaluation of the CO{sup 2} HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid-state NMR analysis of Mesaverde Group, Greater Green River Basin, tight gas sands; characterization of petroleum residua; shallow oil production using horizontal wells with enhanced oil recovery techniques; surface process study for oil recovery using a thermal extraction process;NMR analysis of samples from the ocean drilling program; oil field waste cleanup using tank bottom recovery process; remote chemical sensor development; in situ treatment of manufactured gas plant contaminated soils demonstration program; solid-state NMR analysis of Mowry formation shale from different sedimentary basins; solid-state NMR analysis of naturally and artificially matured kerogens; and development of effective method for the clean-up of natural gas.

  19. The economical production of alcohol fuels from coal-derived synthesis gas. Quarterly technical progress report number 13, October 1--December 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-01-01

    At WVU, Mo{sub 2}S{sub 3} was produced from gas-phase reactions at 1,100 C. The gas-phase reactor was modified to increase product yields and to decrease particle size. Four Chevrel phases were synthesized for catalytic evaluation. In addition, four supported alkali-modified MoS{sub 2} materials were prepared from a single-source precursor, K{sub 2}Mo{sub 3}S{sub 13}. Screening runs have been carried out on some of these materials and others prepared earlier. At UCC and P, test runs on the reactor system have commenced. Higher alcohols up to butanol were observed and identified at high temperatures. Significant progress has been made on the Monte Carlo uncertainty analysis. Frequency distributions have been determined for all of the equipment blocks for the Texaco gasifier cases. For these cases, there is a 10% chance that the actual installed capital cost could exceed the estimated installed capital cost by $40 million dollars. This work will continue with inclusion of variable costs and prediction of the uncertainties in the return on investment. Modifications to the simulated annealing optimization program have been underway in order to increase the level of certainty that the final result is near the global optimum. Alternative design cases have been examined in efforts to enhance the economics of the production of high alcohols. One such process may be the generation of electric power using combustion turbines fueled by synthesis gas.

  20. Characterization of oil and gas waste disposal practices and assessment of treatment costs. Technical progress report, January 1, 1994--March 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Bedient, P.B.

    1994-04-25

    This report covers work completed during the sixth quarter for the project. The project consists of three tasks: the first relates to developing a database of waste volumes and disposal methods used by the industry; the second and third tasks are aimed at investigating technologies that could be used for the treatment of produced waters and developing cost estimates for those technologies. The remainder of this report describes progress related to the three tasks in the project. Overall, construction of the Production Environmental Database (PED) is ongoing. While much of the data has been collected and entered into the database, a few data categories are still missing, for example, soils and geology and geohydrology. Work is currently under way to collect these data. In addition, a detailed data analysis has begun in order to develop relationships between oil and gas activities and environmental characteristics. In terms of the treatment of produced water, much of the work in the past quarter was focused on analyzing the costs associated with the treatment and disposal of waste residuals such as sludges.

  1. Novel microorganism for selective separation of coal from ash and pyrite; First quarterly technical progress report, September 1, 1993--November 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Misra, M.; Smith, R.W.; Raichur, A.M.

    1993-12-31

    This report summarizes the progress made during the first quarter of the research project entitled ``A Novel Microorganism for Selective Separation of Coal from Ash and Pyrite,`` DOE Grant No. DE-FG22-93PC93215. The objective of this project is to study the effectiveness of a novel hydrophobic microorganism, Mycobacterium phlei (M. phlei), for the selective flocculation of coal from pyrite and ash-forming minerals. During the reporting period, three different coal samples: Illinois No. 6 coal, Kentucky No. 9 coal and Pittsburgh No. 8 coal, were collected to be used in the investigation. The microorganism, M. phlei, was obtained as freeze-dried cultures and the growth characteristics of the bacteria were studied. Scanning electron microphotographs revealed that M. phlei cells are coccal in shape and are approximately 1 {mu}m in diameter. Electrokinetic measurements showed that the Illinois No. 6 and Pittsburgh No. 8 coal samples had an isoelectric point (IEP) around pH 6 whereas M. phlei had an IEP around pH 1.5. Electrokinetic measurements of the ruptured microorganisms exhibited an increase in IEP. The increase in IEP of the ruputured cells was due to the release of fatty acids and polar groups from the cell membrane.

  2. Study of the effects of ambient conditions upon the performance of fan powered, infrared, natural gas burners. Quarterly technical progress report, July 1--September 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Bai, T.; Yeboah, Y.D.; Sampath, R.

    1995-10-01

    The objective of this investigation is to characterize the operation of fan powered infrared burner (PIR) at various gas compositions and ambient conditions and develop design guidelines for appliances in containing PIR burners for satisfactory performance. During this period, experimental setup with optical and electronic instrumentation that is necessary for measuring the radiant heat output and the emission gas output of the burner has been established. The radiation measurement instrument, an FTIR, has been purchased and installed in the porous burner experimental system. The radiation measurement capability of the FTIR was tested and found to be satisfactory. A standard blackbody source, made by Graseby Infrared, was employed to calibrate the FTIR. A collection duct for emission gas measurement was fabricated and connected to the existing Horiba gas analyzer. Test runs are being conducted for flue gas analysis. A number of published research papers on modeling of porous burners were reviewed. The physical mechanism and theoretical analysis of the combustion process of the PIR burner was formulated. The numerical modeling, and implementation of a PIR burner code at CAU`s computing facility is in progress.

  3. Wound bed preparation from a clinical perspective

    Directory of Open Access Journals (Sweden)

    A S Halim

    2012-01-01

    Full Text Available Wound bed preparation has been performed for over two decades, and the concept is well accepted. The ′TIME′ acronym, consisting of tissue debridement, i nfection or inflammation, moisture balance and edge effect, has assisted clinicians systematically in wound assessment and management. While the focus has usually been concentrated around the wound, the evolving concept of wound bed preparation promotes the treatment of the patient as a whole. This article discusses wound bed preparation and its clinical management components along with the principles of advanced wound care management at the present time. Management of tissue necrosis can be tailored according to the wound and local expertise. It ranges from simple to modern techniques like wet to dry dressing, enzymatic, biological and surgical debridement. Restoration of the bacterial balance is also an important element in managing chronic wounds that are critically colonized. Achieving a balance moist wound will hasten healing and correct biochemical imbalance by removing the excessive enzymes and growth factors. This can be achieved will multitude of dressing materials. The negative pressure wound therapy being one of the great breakthroughs. The progress and understanding on scientific basis of the wound bed preparation over the last two decades are discussed further in this article in the clinical perspectives.

  4. Engineering development of advanced physical fine coal cleaning for premium fuel applications. Quarterly technical progress report 9, October 1, 1994--December 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Moro, N.; Shields, G.L.; Smit, F.J.; Jha, M.C. [AMAX Research and Development Center, Golden, CO (United States)

    1995-01-25

    The primary goal of this project is the engineering development of two advanced physical fine coal cleaning processes, column flotation and selective agglomeration, for premium fuel applications. The project scope includes laboratory research and bench-scale testing on six coals to optimize these processes, followed by design, and construction of a 2-t/hr process development unit (PDU). The PDU will then be operated to generate 200 ton lots of each of three project coals, by each process. The project began in October, 1992 and is scheduled for completion by March, 1997. During Quarter 9 (October--December, 1995), parametric and optimization testing was completed for the Taggart, Sunnyside, and Indiana VII coal using a 12-inch Microcel{trademark} flotation column. The detailed design of the 2-t/hr PDU grinding, flotation, and dewatering circuits neared completion with the specification of the major pieces of capital equipment to be purchased for these areas. Selective agglomeration test work investigated the properties of various industrial grades of heptane for use during bench- and PDU-scale testing. It was decided to use a hydrotreated grade of commercial heptane due to its low cost and low concentration of aromatic compounds. The final Subtask 6.4 CWF Formulation Studies Test Plan was issued. A draft version of the Subtask 6.5 Preliminary Design and Test Plan Report was also issued, discussing the progress made in the design of the bench-scale selective agglomeration unit. PDU construction work moved forward through the issuing of 26 request for quotations and 21 award packages for capital equipment.

  5. Effects of low-temperature catalytic pretreatments on coal structure and reactivity in liquefaction. Technical progress report, October 1993--December 1993

    Energy Technology Data Exchange (ETDEWEB)

    Song, C.; Huang, L.; Wenzel, K.A.; Hatcher, P.G.; Schobert, H.H.

    1994-02-01

    In this quarter, progress has been made in the following two aspects: The influences of temperature, dispersed Mo catalyst, and solvent on the liquefaction conversion and composition of products from low-rank coals; and the hydrous pyrolysis of a lignite and spectroscopic characterization of its structural transformation during the hydrous pyrolysis. The analytical work described in this quarter also represents molecular-level characterization of products. The purpose of the first part of the work described in this quarter is to study the influences of temperature, solvent and dispersed Mo catalyst on the liquefaction conversion and chemical composition of the products. Many specialty chemicals, including one- to four-ring aromatics, could potentially be produced by liquefying coal. To achieve this goal, not only a high coal conversion but also a desirable product distribution is necessary. Therefore, it is of great importance to understand the structural changes of the coal during reaction and to investigate the conditions under which the aliphatics or aromatics can be removed from the macromolecular structure of coal. This quarterly report also describes the hydrous pyrolysis of Potapsco lignite and spectroscopic characterization of its structural transformation during the hydrous pyrolysis. This work has some implications both on the structural changes of low-rank coals during pretreatment and on the geochemical reactions during coalification stage. Vitrinite, a major component of most coals, is derived from degraded wood in ancient peat swamps. Organic geochemical studies conducted on a series of coalified wood samples derived mostly from gymnosperms have allowed the development of a chemical reaction series to characterize the major coalification reactions which lignin, the major coal-producing component of wood, undergoes.

  6. Adaptive harvest management for the Svalbard population of pink‐footed geese: 2016 progress summary: Technical Report from DCE – Danish Centre for Environment and Energy, No. 86

    Science.gov (United States)

    Johnson, Fred A.; Madsen, Jesper

    2016-01-01

    This document describes progress to date on the development of an adaptive harvest management strategy for maintaining the Svalbard population of pink‐footed geese (Anser brachyrhynchus) near their agreed target level (60,000) by providing for sustainable harvests in Norway and Denmark. This report provides an assessment of the most recent monitoring information (1991-2015) and its implications for the harvest management strategy. By combining varying hypotheses about survival and reproduction, a suite of nine models have been developed that represent a wide range of possibilities concerning the extent to which demographic rates are density dependent or independent. These results suggest that the pink‐footed goose population may have recently experienced a release from density‐dependent mechanisms, corresponding to the period of most rapid growth in population size. Beginning with the 2016 hunting season, harvest quotas will be prescribed on an annual basis rather than every three years because of the potential to better meet population management objectives. Based on updated model weights, the recent observations of population size (74,800), the proportion of the population comprised of one-year-old birds (0.138), and temperature days in Svalbard (20), the optimal harvest quota for the 2016 hunting season is 25,000. The large increase in quota compared to that during first three years of AHM reflects stakeholders’ desire to reduce population size to the goal of 60,000, recognizing that population size remains relatively high and above-average production is expected in 2016 due to a warm spring.

  7. A protocol for evaluating progressive levels of simulation fidelity in the development of technical skills, integrated performance and woman centred clinical assessment skills in undergraduate midwifery students.

    Science.gov (United States)

    Brady, Susannah; Bogossian, Fiona; Gibbons, Kristen; Wells, Andrew; Lyon, Pauline; Bonney, Donna; Barlow, Melanie; Jackson, Anne

    2013-05-24

    Simulation as a pedagogical approach has been used in health professional education to address the need to safely develop effective clinical skills prior to undertaking clinical practice. However, evidence for the use of simulation in midwifery is largely anecdotal, and research evaluating the effectiveness of different levels of simulation fidelity are lacking.Woman centred care is a core premise of the midwifery profession and describes the behaviours of an individual midwife who demonstrates safe and effective care of the individual woman. Woman centred care occurs when the midwife modifies the care to ensure the needs of each individual woman are respected and addressed. However, a review of the literature demonstrates an absence of a valid and reliable tool to measure the development of woman centred care behaviours. This study aims to determine which level of fidelity in simulated learning experiences provides the most effective learning outcomes in the development of woman centred clinical assessment behaviors and skills in student midwives. Three-arm, randomised, intervention trial.In this research we plan to:a) trial three levels of simulation fidelity - low, medium and progressive, on student midwives performing the procedure of vaginal examination;b) measure clinical assessment skills using the Global Rating Scale (GRS) and Integrated Procedural Performance Instrument (IPPI); andc) pilot the newly developed Woman Centred Care Scale (WCCS) to measure clinical behaviors related to Woman-Centredness. This project aims to enhance knowledge in relation to the appropriate levels of fidelity in simulation that yield the best educational outcomes for the development of woman centred clinical assessment in student midwives. The outcomes of this project may contribute to improved woman centred clinical assessment for student midwives, and more broadly influence decision making regarding education resource allocation for maternity simulation.

  8. Installation of a stoker-coal preparation plant in Krakow, Poland. Quarterly technical progress report No. 3, November--December 1994

    Energy Technology Data Exchange (ETDEWEB)

    Rozelle, P.

    1996-01-01

    This report describes the progress made during this reporting period of a two year project to demonstrate that the air pollution from a traveling grate stoker being used to heat water at a central heating plant in Krakow, Poland can be reduced significantly by (1) substituting the unwashed, unsized coal currently being used with a mechanically cleaned, double-sized stoker fuel and by (2) optimizing the operating parameters of the stoker. It is anticipated that these improvements will prove to be cost effective and hence be adopted by the other central heating plants in Krakow and indeed, throughout Eastern European cities where coal continues to be the primary source of fuel. EFH Coal Company has formed a partnership with two Polish institutions -- MPEC, a central heating company in Krakow, and Naftokrak-Naftobudowa, preparation plant designers and fabricators, for the execution of this effort. The washability data from a 20mm x 0.5mm size fraction of raw coal from the Nikwa Modrejow Mine were evaluated. The data show that the ash content of this coal can be reduced from 34.0 percent to 9.0 percent by washing in a heavy-media cyclone at 1.725 sp.gr.; the actual yield of clean coal would be 63.1 percent. This product would meet compliance limitations of 500 a of SO{sub 2}/GJ. An evaluation of the predicted results that can be expected when washing five different candidate Polish coals shows that compliance products containing less than 640 a SO{sub 2}/GJ and 10 percent ash at attractive yields can be produced by washing the raw coals in a heavy-media cyclone. Discussions with financial institutions regarding the cost of producing a quality stoker coal in Poland and for identifying sources of private capital to help cost share the project continued. The search for markets for utilizing surplus production from the new plant continued.

  9. Geomechanics of bedded salt

    Energy Technology Data Exchange (ETDEWEB)

    Serata, S.; Milnor, S.W.

    1979-06-08

    Creep data from the literature search is reinterpreted by SGI, resulting in a better understanding of the temperature and stress state dependence of the octahedral creep rate and the octahedral shear strength. The concept of a transition strength between the elastic and the plastic states is in agreement with the data. The elastic and rheological properties of salt are described, and a set of constitutive equations is presented. The dependence of material properties on parameters such as temperature is considered. Findings on the permeability of salt are summarized, and the in-situ behavior of openings in bedded salt is described based on extensive engineering experience. A stress measuring system utilizing a finite element computer code is discussed. Geological factors affecting the stability of salt openings are considered, and the Stress Control Technique for designing stable openings in bedded salt formations is explained.

  10. Virtual Test Bed

    Science.gov (United States)

    2016-06-07

    project is to develop a benchmark system for evaluating models for predicting the characteristics of ocean wind waves. SCIENTIFIC OBJECTIVES A...transformation-scale models (i.e. models which treat the physics of waves propagating from offshore areas into the coastline). Each phase is further divided...to be assembled within the virtual test bed. Wind fields for running these tests will be obtained from Oceanweather, Inc. from a separate ONR

  11. Technical Network

    CERN Multimedia

    2007-01-01

    In order to optimize the management of the Technical Network (TN), to ease the understanding and purpose of devices connected to the TN, and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive email notifications from IT/CS asking them to add the corresponding information in the network database. Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

  12. Technical Network

    CERN Multimedia

    2007-01-01

    In order to optimise the management of the Technical Network (TN), to facilitate understanding of the purpose of devices connected to the TN and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive e-mails from IT/CS asking them to add the corresponding information in the network database at "network-cern-ch". Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

  13. Cadmium sulfide/copper sulfide heterojunction cell research by sputter deposition. Quarterly technical progress report, March 1, 1981-June 30, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Thornton, J.A.; Anderson, W.W.; Meakin, J.D.

    1981-08-01

    A second series of hybrid cells with sputter-deposited Cu/sub 2/S layers has been fabricated. An efficiency of about 4 3/4%, without antireflection coating, was achieved for one of the cells. This result approaches the 5 3/4% which was achieved in the first set (different Cu/sub 2/S deposition conditions) and confirms the viability of the sputtering process for this application. Significant progress has been made in fabricating all-sputtered cells with CdS layers deposited by planar magnetron reactive sputtering. Efficiencies of approximately 3%, without antireflection coatings, have been achieved in the as-deposited state for seven cells. Individual cells have yielded a J/sub sc/ of 12 mA/cm/sup 2/, a V/sub oc/ of 0.53V, and a fill factor of 0.72. Taken together these parameters would yield an efficiency of 4 1/2%. A strong coupling is found between the properties of the Cu/sub 2/S and CdS layers. However, the conditions which maximize J/sub sc/, V/sub oc/ and the fill factor do not appear to be mutually exclusive. Reflectance measurements indicate that 30% or more of the incident radiation is being reflected from the front surface of the cells over the wavelength range of the solar spectrum. Thus optimization of the cell parameters with a suitable antireflection coating should yield cell efficiencies of about 6%. Characterization of the junctions formed in the all-sputtered cells under near-optimum deposition conditions indicates that they have remarkable properties in their as-deposited state, being very similar to high performance conventional cells after heat treatment. Junction ideality factors are about unity in the light, with J/sub 0/ values of about 2 x 10/sup -8/ mA/cm/sup 2/. Interface recombination velocities are as low as a few times 10/sup 5/ cm/sec. CdS depletion layer widths are about 2000 nm in the dark and collapse to about 200 nm under illumination.

  14. Cadmium sulfide/copper sulfide heterojunction cell research by sputter deposition. Quarterly technical progress report, March 1, 1981-June 30, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Thornton, J.A.; Anderson, W.W.; Meakin, J.D.

    1981-08-01

    A second series of hybrid cells with sputter-deposited Cu/sub 2/S layers has been fabricated. An efficiency of about 4 3/4%, without antireflection coating, was achieved for one of the cells. This result approaches the 5 3/4% which was achieved in the first set (different Cu/sub 2/S deposition conditions) and confirms the viability of the sputtering process for this application. Significant progress has been made in fabricating all-sputtered cells with CdS layers deposited by planar magnetron reactive sputtering. Efficiencies of approximately 3%, without antireflection coatings, have been achieved in the as-deposited state for seven cells. Individual cells have yielded a J/sub sc/ of 12 mA/cm/sup 2/, a V/sub oc/ of 0.53V, and a fill factor of 0.72. Taken together these parameters would yield an efficiency of 4 1/2%. A strong coupling is found between the properties of the Cu/sub 2/S and CdS layers. However, the conditions which maximize J/sub sc/, V/sub oc/ and the fill factor do not appear to be mutually exclusive. Reflectance measurements indicate that 30% or more of the incident radiation is being reflected from the front surface of the cells over the wavelength range of the solar spectrum. Thus optimization of the cell parameters with a suitable antireflection coating should yield cell efficiencies of about 6%. Characterization of the junctions formed in the all-sputtered cells under near-optimum deposition conditions indicates that they have remarkable properties in their as-deposited state, being very similar to high performance conventional cells after heat treatment. Junction ideality factors are about unity in the light, with J/sub 0/ values of about 2 x 10/sup -8/ mA/cm/sup 2/. Interface recombination velocities are as low as a few times 10/sup 5/ cm/sec. CdS depletion layer widths are about 2000 nm in the dark and collapse to about 200 nm under illumination.

  15. Status of the fluidized bed unit

    Energy Technology Data Exchange (ETDEWEB)

    Williams, P.M.; Wade, J.F.

    1994-06-01

    Rocky Flats has a serious mixed waste problem. No technology or company has a license and available facilities to remedy this dilemma. One solution under study is to use a catalytic fluidized bed unit to destroy the combustible portion of the mixed waste. The fluidized bed thermal treatment program at Rocky Flats is building on knowledge gained over twenty years of successful development activity. The FBU has numerous technical advantages over other thermal technologies to treat Rocky Flats` mixed waste, the largest being the lower temperature (700{degrees}C versus 1000{degrees}C) which reduces acid corrosion and mechanical failures and obviates the need for ceramic lining. Successful demonstrations have taken place on bench, pilot, and full-scale tests using radioactive mixed wastes. The program is approaching implementation and licensing of a production-scale fluidized bed system for the safe treatment of mixed waste. The measure for success on this project is the ability to work closely with the community to jointly solve problems and respond to concerns of mixed waste treatment at Rocky Flats.

  16. Modern trends in technical crystallization

    Science.gov (United States)

    Matz, G.

    1980-04-01

    Interesting and significant developments have occurred in the last decade in both crystallization equipment and in the theory of crystallization process. In the field of technical crystallization new crystallizers have been developed and computer modelling has become important in scaling up and in the achievement of increased performance. The DP-Kristaller developed by Escher-Wyss-Tsukishima, the Brodie purifier, the sieve tray column having dancing balls, the automated multiple crystallization process due to Mützenberg and Saxer and the double belt cooler, all of which represent technical developments, are described in the first section. The second part of the paper reviews computer modelling of the fluidized bed crystallizer, chemical precipitation, flaking and prilling. Finally, there is a brief discussion of the impact of technical crystallization processes on environmental protection.

  17. Understanding and predicting bed humidity in fluidized bed granulation.

    Science.gov (United States)

    Hu, Xinhui; Cunningham, John; Winstead, Denita

    2008-04-01

    Bed humidity is a critical parameter that needs to be controlled in a fluidized bed granulation to ensure reliability. To predict and control the bed humidity during the fluidized bed granulation process, a simple model based on the mass conservation of moisture was developed. The moisture mass balance model quantitatively simulates the effects of spray rate, binder solution concentration, airflow rate, inlet air temperature, and dew point on the bed humidity. The model was validated by a series of granulations performed in different scale granulators including Glatt GPCG-1, GPCG-15, and GPCG-60. Good agreement was observed between the theoretical prediction and the measured loss on drying (LOD). The model developed in the current work enables us to choose the appropriate parameters for the fluidized bed granulation and can be used as a valuable tool in process scaling-up.

  18. Hazards of Fluoride Pollution and Technical Research Progress of Treating Fluoride-containing Wastewater%氟污染的危害及含氟废水处理技术研究进展

    Institute of Scientific and Technical Information of China (English)

    雷绍民; 郭振华

    2012-01-01

    Conclude the fluoride pollution sources, introduce the hazards of fluoride pollution, discuss the fluoride-containing wastewater treatment technical research progress, and analyze the existing problems of fluoride-containing wastewater treatment methods, finally point out that the new functional materials, combination process and resource utilization technology are the key orientation of fluoride-containing wastewater treatment research. Keywords Sources of fluoride pollution,Hazards of fluoride pollution,Fluoride-containing wastewater treatment tech-%归纳了氟污染的来源,介绍了氟污染的危害,论述了含氟废水处理技术的研究进展,并分析了各种含氟废水处理方法存在的问题.最后指出新型功能材料、联合工艺及含氟废水资源化利用技术是今后含氟废水处理研究的重点方向.

  19. 合成气经草酸酯法制取乙二醇的技术进展%Technical Progress of Ethylene Glycol Made of Ethyl Oxalate Method from Synthetic Gas

    Institute of Scientific and Technical Information of China (English)

    张艳梅; 石自更

    2011-01-01

    Author has analyzed the supply/demand situations of ethylene glycol and the advantages for developing the ethylene glycol made by coal;has discussed the process principle,process flow and technical progress for ethylene glycol made by ethyl oxalate method;has indicated that strengthening the research on hydrogenation catalyst for ethyl oxalate and establishing the industrialized demonstration plant with a definite scale is the urgent matter for making the large-scale industrialized production for process technology of ethylene glycol made by ethyl oxalate method from synthetic gas.%分析了当前国内乙二醇的供需状况和发展煤制乙二醇的优势;论述了草酸酯法制取乙二醇的工艺原理、工艺流程和技术进展;指出加强草酸酯加氢催化剂的研究并建立一定规模的工业化示范装置是合成气经草酸酯法制乙二醇工艺技术进入大规模工业化生产的当务之急。

  20. Innovative Clean Coal Technology (ICCT): 500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Technical progress report, First quarter 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-12-31

    This quarterly report discusses the technical progress of an Innovative Clean Coal Technology (ICCT) demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. The project is being conducted at Georgia Power Company`s Plant Hammond Unit 4 located near Rome, Georgia. The primary goal of this project is the characterization of the low NO{sub x} combustion equipment through the collection and analysis of long-term emissions data. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project. The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO{sub x} burners (LNB). During each test phase of the project, diagnostic, performance, long-term, and verification testing will be performed. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency.

  1. Preliminary study of the behavioral and biological effects of high intensity 60 Hz electric fields. Quarterly technical progress report, No. 1. [Development and testing of experimental protocols and apparatus

    Energy Technology Data Exchange (ETDEWEB)

    1978-08-01

    The major objective of this preliminary study is to develop and thoroughly test the experimental protocols and apparatus, which are planned for a major study of the behavioral and biological effects of high intensity 60 Hz electric fields. The behavior of baboons will be observed before, during, and after exposure to 60 Hz electric fields at a maximum intensity of 60 kV/m. Both individual performance (operant conditioning) and social behavior will be examined. The preliminary study will differ from the planned major study as follows: subjects will be used as their own controls; a smaller number of subjects will be run; field intensity will not be varied; the electric field should be non-uniform; the preliminary study exposure facility will be basically an outdoor facility; to avoid deterioration of plastic materials, the high intensity fields will not be turned on during or just after rainfall; and in the preliminary study the biological work will be restricted to the clinical determination of the health of subjects before and after exposure. The present report is the first of three quarterly technical progress reports. It covers approximately the first two and one-half months of activity and, therefore, consists primarily of plans. The report addresses four major areas: the high intensity field exposure facility; the field measurement instrumentation; the operation conditioning equipment; and experimental methods including experimental design and data analysis.

  2. Coal Bed Methane Primer

    Energy Technology Data Exchange (ETDEWEB)

    Dan Arthur; Bruce Langhus; Jon Seekins

    2005-05-25

    During the second half of the 1990's Coal Bed Methane (CBM) production increased dramatically nationwide to represent a significant new source of income and natural gas for many independent and established producers. Matching these soaring production rates during this period was a heightened public awareness of environmental concerns. These concerns left unexplained and under-addressed have created a significant growth in public involvement generating literally thousands of unfocused project comments for various regional NEPA efforts resulting in the delayed development of public and fee lands. The accelerating interest in CBM development coupled to the growth in public involvement has prompted the conceptualization of this project for the development of a CBM Primer. The Primer is designed to serve as a summary document, which introduces and encapsulates information pertinent to the development of Coal Bed Methane (CBM), including focused discussions of coal deposits, methane as a natural formed gas, split mineral estates, development techniques, operational issues, producing methods, applicable regulatory frameworks, land and resource management, mitigation measures, preparation of project plans, data availability, Indian Trust issues and relevant environmental technologies. An important aspect of gaining access to federal, state, tribal, or fee lands involves education of a broad array of stakeholders, including land and mineral owners, regulators, conservationists, tribal governments, special interest groups, and numerous others that could be impacted by the development of coal bed methane. Perhaps the most crucial aspect of successfully developing CBM resources is stakeholder education. Currently, an inconsistent picture of CBM exists. There is a significant lack of understanding on the parts of nearly all stakeholders, including industry, government, special interest groups, and land owners. It is envisioned the Primer would being used by a variety of

  3. Bed Rest Muscular Atrophy

    Science.gov (United States)

    Greenleaf, John E.

    2000-01-01

    A major debilitating response from prolonged bed rest (BR) is muscle atrophy, defined as a "decrease in size of a part of tissue after full development has been attained: a wasting away of tissue as from disuse, old age, injury or disease". Part of the complicated mechanism for the dizziness, increased body instability, and exaggerated gait in patients who arise immediately after BR may be a result of not only foot pain, but also of muscular atrophy and associated reduction in lower limb strength. Also, there seems to be a close association between muscle atrophy and bone atrophy. A discussion of many facets of the total BR homeostatic syndrome has been published. The old adage that use determines form which promotes function of bone (Wolff's law) also applies to those people exposed to prolonged BR (without exercise training) in whom muscle atrophy is a consistent finding. An extreme case involved a 16-year-old boy who was ordered to bed by his mother in 1932: after 50 years in bed he had "a lily-white frame with limbs as thin as the legs of a ladder-back chair". These findings emphasize the close relationship between muscle atrophy and bone atrophy. In addition to loss of muscle mass during deconditioning, there is a significant loss of muscle strength and a decrease in protein synthesis. Because the decreases in force (strength) are proportionately greater than those in fiber size or muscle cross-sectional area, other contributory factors must be involved; muscle fiber dehydration may be important.

  4. Bed Rest Muscular Atrophy

    Science.gov (United States)

    Greenleaf, John E.

    2000-01-01

    A major debilitating response from prolonged bed rest (BR) is muscle atrophy, defined as a "decrease in size of a part of tissue after full development has been attained: a wasting away of tissue as from disuse, old age, injury or disease". Part of the complicated mechanism for the dizziness, increased body instability, and exaggerated gait in patients who arise immediately after BR may be a result of not only foot pain, but also of muscular atrophy and associated reduction in lower limb strength. Also, there seems to be a close association between muscle atrophy and bone atrophy. A discussion of many facets of the total BR homeostatic syndrome has been published. The old adage that use determines form which promotes function of bone (Wolff's law) also applies to those people exposed to prolonged BR (without exercise training) in whom muscle atrophy is a consistent finding. An extreme case involved a 16-year-old boy who was ordered to bed by his mother in 1932: after 50 years in bed he had "a lily-white frame with limbs as thin as the legs of a ladder-back chair". These findings emphasize the close relationship between muscle atrophy and bone atrophy. In addition to loss of muscle mass during deconditioning, there is a significant loss of muscle strength and a decrease in protein synthesis. Because the decreases in force (strength) are proportionately greater than those in fiber size or muscle cross-sectional area, other contributory factors must be involved; muscle fiber dehydration may be important.

  5. Trends in hospital bed utilisation in New Zealand 1989 to 2006: more or less beds in the future?

    Science.gov (United States)

    Malcolm, Laurence

    2007-10-26

    Reduction in hospital bed utilisation has been a key factor in controlling costs in recent decades in many health systems, including New Zealand's. This paper has the following aims: to analyse trends in hospital bed utilisation from 1988 to 2006; to examine variation between district health boards (DHBs); to consider factors which may explain the trends observed; to compare the results with international trends; and to discuss future need for beds and factors affecting this need, including the integrated DHB system. Ministry of Health Hospital Throughput reports for 1988/89 to 2005/06 were accessed and present standardised, filtered, and truncated data on discharges, average length of stay (ALOS), bed days, and DHB comparisons. Data on beds were also obtained from the Private Surgical Hospitals Association. Rates of utilisation were calculated using Statistics New Zealand and the Ministry of Health population data. Australian, UK, and US comparisons were obtained. The New Zealand data showed a continuing rise in discharge rates, especially case weighted. This was almost entirely due to the increase in day patients. There was a marked downward trend in bed day rates due to a more than 50% decline in the ALOS and a corresponding decline in bed availability. There was a marked variation between DHBs in standardised discharge ratios in 2005/06, with low rates indicating potential benchmarks to which higher utilisation DHBs might aspire. New Zealand was well ahead of both Australia and the UK National Health System (NHS) in reducing bed utilisation but comparisons with Kaiser Permanente indicated that DHBs could potentially, even dramatically, reduce bed utilisation through reducing admissions. The findings point to important progress in New Zealand in containing costs associated with hospital bed utilisation. Future strategies need to focus strongly on reducing hospital admissions through PHO action to provide community alternatives and chronic disease management.

  6. Racing for the Bed

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    No one knows when the people ofMacheng City began to employthe marriage custom of racingfor the bed, once a custom unique to theTujia ethnic minority. It is said that at the end of awedding, bride and bridegroom enter thebridal chamber together and race for thebed. The one who is the first to sit on thebed will be the master of the new familyIt sounds unreasonable, but quite anumber of people believe in it.Therefore, on the wedding night, manybrides and bridegrooms try their best to

  7. Biparticle fluidized bed reactor

    Science.gov (United States)

    Scott, C.D.

    1993-12-14

    A fluidized bed reactor system which utilizes a fluid phase, a retained fluidized primary particulate phase, and a migratory second particulate phase is described. The primary particulate phase is a particle such as a gel bead containing an immobilized biocatalyst. The secondary particulate phase, continuously introduced and removed in either cocurrent or countercurrent mode, acts in a secondary role such as a sorbent to continuously remove a product or by-product constituent from the fluid phase. Introduction and removal of the sorbent phase is accomplished through the use of feed screw mechanisms and multivane slurry valves. 3 figures.

  8. A Spouted Bed Reactor Monitoring System for Particulate Nuclear Fuel

    Energy Technology Data Exchange (ETDEWEB)

    D. S. Wendt; R. L. Bewley; W. E. Windes

    2007-06-01

    Conversion and coating of particle nuclear fuel is performed in spouted (fluidized) bed reactors. The reactor must be capable of operating at temperatures up to 2000°C in inert, flammable, and coating gas environments. The spouted bed reactor geometry is defined by a graphite retort with a 2.5 inch inside diameter, conical section with a 60° included angle, and a 4 mm gas inlet orifice diameter through which particles are removed from the reactor at the completion of each run. The particles may range from 200 µm to 2 mm in diameter. Maintaining optimal gas flow rates slightly above the minimum spouting velocity throughout the duration of each run is complicated by the variation of particle size and density as conversion and/or coating reactions proceed in addition to gas composition and temperature variations. In order to achieve uniform particle coating, prevent agglomeration of the particle bed, and monitor the reaction progress, a spouted bed monitoring system was developed. The monitoring system includes a high-sensitivity, low-response time differential pressure transducer paired with a signal processing, data acquisition, and process control unit which allows for real-time monitoring and control of the spouted bed reactor. The pressure transducer is mounted upstream of the spouted bed reactor gas inlet. The gas flow into the reactor induces motion of the particles in the bed and prevents the particles from draining from the reactor due to gravitational forces. Pressure fluctuations in the gas inlet stream are generated as the particles in the bed interact with the entering gas stream. The pressure fluctuations are produced by bulk movement of the bed, generation and movement of gas bubbles through the bed, and the individual motion of particles and particle subsets in the bed. The pressure fluctuations propagate upstream to the pressure transducer where they can be monitored. Pressure fluctuation, mean differential pressure, gas flow rate, reactor

  9. [How beds for tuberculosis be provided and utilized?].

    Science.gov (United States)

    Shimao, Tadao

    2002-01-01

    In 1951 when TB Control Law was legislated, and the government of Japan started intensive TB programme mainly consisting of mass health examination, BCG vaccination and distribution of appropriate treatment for TB cases, there were about 100,000 beds for TB, similar to the number of then TB deaths, and many TB patients died before admission to sanatoria. Urgent measures were taken to increase beds for TB with a target of 250,000, 2.5 times of then TB death. The target was achieved in 1957. Thereafter, the number of beds for TB as well as the occupancy rate had decreased with the decline of TB, and then policy on beds for TB could be summarized as follows: (1) top priority was given to increase the number of beds for TB, (2) general hospitals were improved with the progress of medical science and economic development, while no improvement was done on TB beds with the assumption that the need for TB beds will soon disappear, (3) minimum unit of TB beds was a TB ward with generally 40 to 50 beds, (4) an idea to provide TB bed in a general hospital came out only since 1992 as a small model project, (5) it was intended to segregate infectious TB patients from the community, however, no consideration was made about super-infection among patients themselves and the infection to health care workers, (6) admission of TB cases to a general bed and admission of non-TB cases to a TB ward was not legally permitted, (7) cost for TB treatment was set on a low level. Recent data indicate that the occupancy rate of TB beds was 43.5%, and the average stay in TB beds is still slightly over 100 days, and observing by prefectures, marked differences were seen. Taking into account changes in the pattern on TB patients such as aging and the increase of cases with serious complications and most health care workers in TB wards are not yet infected with TB, it is needed to divide TB beds into two types, one for new cases and the other for chronic cases. Beds for new cases should be provided

  10. Study of fluidized-bed desulfurization with zinc ferrite

    Energy Technology Data Exchange (ETDEWEB)

    Grindley, T

    1991-01-01

    Previous work established the technical feasibility of desulfurizing the hot product gases of coal gasification with fixed beds of a regenerable zinc ferrite sorbent. This process, intended for integration with coal gasifiers and gas turbines, has been tested and studied in considerable detail in a process development unit. Though possessing the advantages of high-sulfur absorption at low-sulfur breakthrough and the lack of sorbent attrition characteristic of a stationary bed, fixed beds also have inherent disadvantages: susceptibility to plugging by particles and a large diluent requirement during regeneration to control the reaction zone temperature. Therefore, METC conducted a scoping laboratory test program to determine the desulfurizing capability of fluid beds of zinc ferrite. Results from this program are presented. The results generally demonstrated that fluid beds of zinc ferrite have the potential to lower the H{sub 2}S level in hot gas from 10,000 to 10 ppmv. To achieve this at a high-sorbent sulfur loading would require two fluid-bed stages. Sorbent attrition appears to be acceptably low. Planned future activities include tests at high pressure with both simulated gas and in a gasifier sidestream.

  11. BED UTILIZATION IN CARDIO VASCULAR AND THORACIC SURGERY WARD

    Directory of Open Access Journals (Sweden)

    Ishtyak

    2015-11-01

    Full Text Available BACKGROUND: Of all the subsystems of a hospital, inpatient care occupies prime place in terms of resource consumed, use of specialized technical man power, technology and skill. In spite of the huge investment of money, material and the manpower at times even the basic needs of patients are not met. AIMS: The study was conducted, to observe the average length of stay (ALS of patients in cardio vascular and thoracic Surgery (CVTS ward, and to find out the bed occupancy rate. METHODS: The admission and discharge record of all the patients was recorded from the report books, hospital files of all the patients were checked to know complete biodata. Medical record section was consulted and admission discharge register/files were recorded to know the symptomatology, clinical findings, diagnosis and the management thereof. Mortality and morbidity was recorded from admission files. RESULTS: A total of 732 patients were admitted on a bed complement of 11712 days having 8639 bed days. 84.28% of the patients underwent surgical procedures. Daily average beds occupied were 23.60 beds per day, average length of stay was 11.23 days, and 73.76% was the bed occupancy rate. CONCLUSION: Patients having major operations had more length of stay compared to patients who were admitted after pre anesthetic checkup and full planning from outdoor departments. Preadmission evaluation, pre anesthetic checkup and preventing post-operative morbidity decrease length of stay

  12. Imagining Technicities

    DEFF Research Database (Denmark)

    Liboriussen, Bjarke; Plesner, Ursula

    2011-01-01

    The actors of the building industry have access to a range of Information and Communication Technologies (ICTs), and are constantly presented with new software and new communications platforms. Through case studies, and inspired by sociotechnical approaches to the study of emerging technologies......, this article focuses on innovative uses of virtual worlds in architecture. We interviewed architects, industrial designers and other practitioners. Conceptually supported by an understanding of technicity found in Cultural Studies, the interviews were then coded with a focus on interviewees’ references...... to the elements of taste and skill. In the final analysis those references were synthesized as five imagined technicities: the architect, the engineer, the client, the Chinese, and the Virtual World native. Because technicities are often assumed and rarely discussed as actants who influence practice, their role...

  13. Imagining Technicities

    DEFF Research Database (Denmark)

    Liboriussen, Bjarke; Plesner, Ursula

    2011-01-01

    , this article focuses on innovative uses of virtual worlds in architecture. We interviewed architects, industrial designers and other practitioners. Conceptually supported by an understanding of technicity found in Cultural Studies, the interviews were then coded with a focus on interviewees’ references......The actors of the building industry have access to a range of Information and Communication Technologies (ICTs), and are constantly presented with new software and new communications platforms. Through case studies, and inspired by sociotechnical approaches to the study of emerging technologies...... to the elements of taste and skill. In the final analysis those references were synthesized as five imagined technicities: the architect, the engineer, the client, the Chinese, and the Virtual World native. Because technicities are often assumed and rarely discussed as actants who influence practice, their role...

  14. Bullous reactions to bed bug bites reflect cutaneous vasculitis

    Science.gov (United States)

    This study evaluates bullous cutaneous reactions and sequential histopathology in an individual sensitized to bed bug bites in an effort to better understand the allergic response and histology associated with these bites. There was a progression of the inflammatory response across time ranging from...

  15. Fossil energy program. Progress report, May 1978

    Energy Technology Data Exchange (ETDEWEB)

    McNeese, L.E.

    1978-06-01

    Results are reported from hydrocarbonization of Illinois No. 6 coal in the bench-scale reactor. All heat treatment for as-quenched, quenched and tempered, and stress relieved samples of 2-/sup 1///sub 4/ Cr-1 Mo steel is complete and some aging is in progress. Impact testing of material that was slow-cooled (0.3 K/sec) from 1038/sup 0/C and subsequently heat treated has been completed. Work is underway on COGAS process residues and attempts are underway to secure representative SRC wastes. The Environmental Monitoring Handbook was completed. Technical assistance was provided to DOE/FE on four demonstration plants: Grace/Ebasco; Memphis Light, Gas and Water; ICGG; and CONOCO Work was initiated on the atmospheric fluidized bed combustion assessment. In process modeling the revised physical properties package was received from Purdue and has been compiled and linked into the subroutine library. Evaluation of market demand for coal conversion equipment is continuing. Process flowsheets were completed for all major plant units of the in situ syngas-to-gasoline facility. Material and heat balances for the M-gasoline plant were revised. In hygas modeling work continues on the areas of devolatilization, the characterization and thermal cracking behavior of coal derived liquids, model definition and thermal cracking behavior, model definition and development of a multiple bed simulation program. Information for the H-Coal process has been collected. Fixed capital cost estimates and profitability analyses for the SRC-II, CSF, and H-Coal processes are in progress. Monitoring of the HYGAS Pilot Plant continues.

  16. CIRCULATING MOVING BED COMBUSTION PROOF OF CONCEPT

    Energy Technology Data Exchange (ETDEWEB)

    Jukkola, Glen

    2010-06-30

    Circulating Moving Bed (CMB) combustion technology has its roots in traditional circulating fluidized bed technology and involves a novel method of solid fuel combustion and heat transfer. CMB technology represents a step change in improved performance and cost relative to conventional PC and FBC boilers. The CMB heat exchanger preheats the energy cycle working fluid, steam or air, to the high temperature levels required in systems for advanced power generation. Unique features of the CMB are the reduction of the heat transfer surfaces by about 60% as a result of the enhanced heat transfer rates, flexibility of operation, and about 30% lower cost over existing technology. The CMB Phase I project ran from July 2001 through March 2003. Its objective was to continue development of the CMB technology with a series of proof of concept tests. The tests were conducted at a scale that provided design data for scale up to a demonstration plant. These objectives were met by conducting a series of experiments in ALSTOM Power’s Multi-use Test Facility (MTF). The MTF was modified to operate under CMB conditions of commercial interest. The objective of the tests were to evaluate gas-to-solids heat transfer in the upper furnace, assess agglomeration in the high temperature CMB bubbling bed, and evaluate solids-to-tube heat transfer in the moving bed heat exchanger. The Phase I program results showed that there are still some significant technical uncertainties that needed to be resolved before the technology can be confidently scaled up for a successful demonstration plant design. Work remained in three primary areas: • scale up of gas to solid heat transfer • high temperature finned surface design • the overall requirements of mechanical and process design. The CMB Phase II workscope built upon the results of Phase I and specifically addressed the remaining technical uncertainties. It included a scaled MTF heat transfer test to provide the necessary data to scale up gas

  17. Variability of Bed Drag on Cohesive Beds under Wave Action

    Directory of Open Access Journals (Sweden)

    Ilgar Safak

    2016-04-01

    Full Text Available Drag force at the bed acting on water flow is a major control on water circulation and sediment transport. Bed drag has been thoroughly studied in sandy waters, but less so in muddy coastal waters. The variation of bed drag on a muddy shelf is investigated here using field observations of currents, waves, and sediment concentration collected during moderate wind and wave events. To estimate bottom shear stress and the bed drag coefficient, an indirect empirical method of logarithmic fitting to current velocity profiles (log-law, a bottom boundary layer model for combined wave-current flow, and a direct method that uses turbulent fluctuations of velocity are used. The overestimation by the log-law is significantly reduced by taking turbulence suppression due to sediment-induced stratification into account. The best agreement between the model and the direct estimates is obtained by using a hydraulic roughness of 10 - 4 m in the model. Direct estimate of bed drag on the muddy bed is found to have a decreasing trend with increasing current speed, and is estimated to be around 0.0025 in conditions where wave-induced flow is relatively weak. Bed drag shows an increase (up to fourfold with increasing wave energy. These findings can be used to test the bed drag parameterizations in hydrodynamic and sediment transport models and the skills of these models in predicting flows in muddy environments.

  18. Variability of bed drag on cohesive beds under wave action

    Science.gov (United States)

    Safak, Ilgar

    2016-01-01

    Drag force at the bed acting on water flow is a major control on water circulation and sediment transport. Bed drag has been thoroughly studied in sandy waters, but less so in muddy coastal waters. The variation of bed drag on a muddy shelf is investigated here using field observations of currents, waves, and sediment concentration collected during moderate wind and wave events. To estimate bottom shear stress and the bed drag coefficient, an indirect empirical method of logarithmic fitting to current velocity profiles (log-law), a bottom boundary layer model for combined wave-current flow, and a direct method that uses turbulent fluctuations of velocity are used. The overestimation by the log-law is significantly reduced by taking turbulence suppression due to sediment-induced stratification into account. The best agreement between the model and the direct estimates is obtained by using a hydraulic roughness of 10  m in the model. Direct estimate of bed drag on the muddy bed is found to have a decreasing trend with increasing current speed, and is estimated to be around 0.0025 in conditions where wave-induced flow is relatively weak. Bed drag shows an increase (up to fourfold) with increasing wave energy. These findings can be used to test the bed drag parameterizations in hydrodynamic and sediment transport models and the skills of these models in predicting flows in muddy environments.

  19. Technical Progress of China's Delayed Coking Technology

    Institute of Scientific and Technical Information of China (English)

    Zhang Lixin; Li Hejie

    2005-01-01

    This article introduces the recent advances of China in the fields of process technology of delayed coking, enlarged equipment size, hydraulic decoking, automatic control and environmental protection. By the end of 2004 the total capacity of delayed coking units in China had reached 37.24Mt/a with the maximum coke drum diameter equating to 9.4 m. This article also presents the investment in delayed cokers and the current production status while pointing out the existing problems and future development trends.

  20. Quarterly Technical Progress Report June 2015

    Energy Technology Data Exchange (ETDEWEB)

    Buchholz, Bruce A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-06-08

    The project has two main goals: 1) Identify the types of adducts naphthalene (NA) forms with DNA and 2) determine whether adduct formation correlates with site selective tumor formation in defined subcompartments of the respiratory tract (respiratory and olfactory nasal epithelium and airways of mice, rats and rhesus monkeys). Five tasks are associated with the completion of the goals. Task 1: Contracting and Animal Use Approvals. IACUC and ACURO approvals are complete, The subcontract with UC Davis (UCD) was executed in December 2014. Task 2: Perform In Vitro Study for Goal 1. Rat samples exposed and in freezer while adduct standards are being made. Mouse samples need to be exposed in next quarter. Task 3: Perform In Vitro Study for Goal 2. Mouse ex vivo samples completed. Rat and monkey samples need to be completed in the next quarter. Task 4: Sample Preparation and Analysis. Mouse Goal 2 samples completed. Other samples remain to be done. Task 5: Data Interpretation and Reporting. Need rat data to write paper on adduct formation.

  1. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball

    2010-01-01

    Operational Experience At the end of the first full-year running period of LHC, CMS is established as a reliable, robust and mature experiment. In particular common systems and infrastructure faults accounted for <0.6 % CMS downtime during LHC pp physics. Technical operation throughout the entire year was rather smooth, the main faults requiring UXC access being sub-detector power systems and rack-cooling turbines. All such problems were corrected during scheduled technical stops, in the shadow of tunnel access needed by the LHC, or in negotiated accesses or access extensions. Nevertheless, the number of necessary accesses to the UXC averaged more than one per week and the technical stops were inevitably packed with work packages, typically 30 being executed within a few days, placing a high load on the coordination and area management teams. It is an appropriate moment for CMS Technical Coordination to thank all those in many CERN departments and in the Collaboration, who were involved in CMS techni...

  2. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball

    2010-01-01

    Operational Experience Since the closure of the detector in February, the technical operation of CMS has been quite smooth and reliable. Some minor interventions in UXC were required to cure failures of power supplies, fans, readout boards and rack cooling connections, but all these failures were repaired in scheduled technical stops or parasitically during access dedicated to fixing LHC technical problems. The only occasion when CMS had to request an access between fills was to search for the source of an alarm from the leak-detection cables mounted in the DT racks. After a few minutes of diagnostic search, a leaking air-purge was found. Replacement was complete within 2 hours. This incident demonstrated once more the value of these leak detection cables; the system will be further extended (during the end of year technical stop) to cover more racks in UXC and the floor beneath the detector. The magnet has also been operating reliably and reacted correctly to the 14s power cut on 29 May (see below). In or...

  3. Bioethics for Technical Experts

    Science.gov (United States)

    Asano, Shigetaka

    Along with rapidly expanding applications of life science and technology, technical experts have been implicated more and more often with ethical, social, and legal problems than before. It should be noted that in this background there are scientific and social uncertainty elements which are inevitable during the progress of life science in addition to the historically-established social unreliability to scientists and engineers. In order to solve these problems, therefore, we should establish the social governance with ‘relief’ and ‘reliance’ which enables for both citizens and engineers to share the awareness of the issues, to design social orders and criterions based on hypothetical sense of values for bioethics, to carry out practical use management of each subject carefully, and to improve the sense of values from hypothetical to universal. Concerning these measures, the technical experts can learn many things from the present performance in the medical field.

  4. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Monday 9 February 2004 From 10:00 to 12:00 - IT Auditorium - bldg. 31, 3rd floor ANSOFT High-Frequency Seminar David Prestaux, Application Engineer, ANSOFT F-78535 BUC, France This Technical Training seminar will present two Ansoft application products: Ansoft HFSS and Ansoft Designer. Ansoft HFSS makes use of the Finite Element Method (FEM) to calculate field solutions from first principles. It can accurately predict all high-frequency behaviours such as dispersion, mode conversion, and losses due to materials and radiation. Ansoft Designer is a suite of design tools to fully integrate high-frequency, physics-based electromagnetic simulations into a seamless system-level simulation environment. Ansoft Designer uses a simple interface to give complete control over every design task, by a method allowing multiple solvers, Solver on Demand. • Introduction • Overview of the Ansoft Total solution • Ansoft HFSS 9...

  5. Paleomagnetism of red beds of Early Devonian age from Central Iran

    NARCIS (Netherlands)

    Wensink, H.

    1983-01-01

    Paleomagnetic results are reported from 13 sites of red beds of Early Devonian age from Central Iran. Detailed paleomagnetic analyses were carried out. Two types of partial progressive demagnetization were applied, one using alternating magnetic fields, the other heating.

  6. Compreendendo a lacuna entre a prática e a evolução técnico-científica do banho no leito Comprendiendo la laguna entre la práctica y la evolución técnico-científica del baño en la cama Understanding the gap between practice and the technical-scientific evolution of the bed-bath

    Directory of Open Access Journals (Sweden)

    Silaine Sandrini Alves Maciel

    2006-04-01

    nursing when the patient becomes dependent on nursing care for the bed-bath. The theoretical model shows the meaning of the patient experience in the bed-bath, integrated by the core category - proposing a nursing model for the bed-bath according to the patient assessment process, as opposed to the technical-scientific evolution of this procedure.

  7. SEWAGE SLUDGE COMBUSTION IN A SPOUTED BED CASCADE SYSTEM

    Institute of Scientific and Technical Information of China (English)

    Mirko Barz

    2003-01-01

    @@ In modern society, sewage is disposed of in a two-step process: it is first made into granules and the sewage sludge granules are then burned in an appropriate combustor. The present paper describes a spouted bed cascade system for sewage sludge combustion developed at the Technical University of Berlin at the turn of the present century. Combustion results in the recovery of the combustible matters of the sewage in the form of thermal energy.

  8. The Latest Progress and Major Technical Changes of API SPEC 5CT%API SPEC 5CT标准最新进展及主要技术内容变化

    Institute of Scientific and Technical Information of China (English)

    方伟; 秦长毅; 许晓锋; 徐婷

    2012-01-01

    从引言部分、正文部分以及附录中的主要修改内容详细介绍了美国石油学会API SPEC 5CT《套管和油管规范》的最新进展,以及该标准新版与前版之间的主要技术内容变化,供套管和油管相关生产厂、油田用户、监督检验人员等在生产、检验过程中更好地使用标准作参考.建议有关各方应加强API和ISO标准信息的跟踪和研究,及时掌握核心标准的变化,使国内生产企业和用户能及时应对.%The latest progress of API SPEC 5CT Specification for Casing and Tubing, as well as the major technical changes of the latest edition and the previous edition of this standard were introduced from foreword, text and the main revised contents in appendix . This standard will provide reference for the personnel that work in relative manufacturing plant, oilfield customers, the supervision & inspection staff and others to use this standard well during production and inspection . It suggests related parties strengthen the tracking and research on API, ISO standard information, promptly grasp the changes of core standards and enable China domestic manufacturers and users to respond in time.

  9. Innovative Clean Coal Technology (ICCT): 500 MW demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. Third quarterly technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-31

    This quarterly report discusses the technical progress of an Innovative Clean Coal Technology (ICCT) demonstration of advanced wall-fired combustion techniques for the reduction of nitrogen oxide (NO{sub x}) emissions from coal-fired boilers. The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO{sub x} burners (LNB). During each test phase of the project, diagnostic, performance, long-term, and verification testing will be performed. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions on other combustion parameters such as particulate characteristics and boiler efficiency. Baseline, AOFA, LNB, and LNB plus AOFA test segments have been completed. Analysis of the 94 days of LNB long-term data collected show the full-load NO{sub x} emission levels to be approximately 0.65 lb/MBtu with fly ash LOI values of approximately 8 percent. Corresponding values for the AOFA configuration are 0.94 lb/MBtu and approximately 10 percent. For comparison, the long-term full-load, baseline NO{sub x} emission level was approximately 1.24 lb/MBtu at 5.2 percent LOI. Comprehensive testing in the LNB+AOFA configuration indicate that at full-load, NO{sub x} emissions and fly ash LOI are near 0.40 lb/MBtu and 8 percent, respectively. However, it is believed that a substantial portion of the incremental change in NO{sub x} emissions between the LNB and LNB+AOFA configurations is the result of additional burner tuning and other operational adjustments and is not the result of the AOFA system. During this quarter, LNB+AOFA testing was concluded. Testing performed during this quarter included long-term and verification testing in the LNB+AOFA configuration.

  10. Effectiveness of Bed Bug Pesticides

    Science.gov (United States)

    Before EPA allows a bed bug claim on a label, the product must be supported by data showing it will kill bed bugs when applied according to the label. Also consider factors such as extent of infestation, site preparation, and insect life stages.

  11. Bed Bug Laws and Regulations

    Science.gov (United States)

    21 states have some level of regulation with regard to bed bugs. Most of these requirements focus on hotels and landlords or other property managers. The Department of Housing and Urban Development has guidance on controlling bed bugs in public housing.

  12. Debris-bed friction of hard-bedded glaciers

    Science.gov (United States)

    Cohen, D.; Iverson, N.R.; Hooyer, T.S.; Fischer, U.H.; Jackson, M.; Moore, P.L.

    2005-01-01

    [1] Field measurements of debris-bed friction on a smooth rock tablet at the bed of Engabreen, a hard-bedded, temperate glacier in northern Norway, indicated that basal ice containing 10% debris by volume exerted local shear traction of up to 500 kPa. The corresponding bulk friction coefficient between the dirty basal ice and the tablet was between 0.05 and 0.08. A model of friction in which nonrotating spherical rock particles are held in frictional contact with the bed by bed-normal ice flow can account for these measurements if the power law exponent for ice flowing past large clasts is 1. A small exponent (n glacier sliding at 20 m a-1 with a geothermally induced melt rate of 0.006 m a-1 and an effective pressure of 300 kPa can exceed 100 kPa. Debris-bed friction can therefore be a major component of sliding resistance, contradicting the common assumption that debris-bed friction is negligible. Copyright 2005 by the American Geophysical Union.

  13. Fixed bed gasification of solid biomass fuels

    Energy Technology Data Exchange (ETDEWEB)

    Haavisto, I. [Condens Oy, Haemeenlinna (Finland)

    1996-12-31

    Fixed bed biomass gasifiers are feasible in the effect range of 100 kW -10 MW. Co-current gasification is available only up to 1 MW for technical reasons. Counter-current gasifiers have been used in Finland and Sweden for 10 years in gasification heating plants, which are a combination of a gasifier and an oil boiler. The plants have proved to have a wide control range, flexible and uncomplicated unmanned operation and an excellent reliability. Counter-current gasifiers can be applied for new heating plants or for converting existing oil and natural gas boilers into using solid fuels. There is a new process development underway, aiming at motor use of the producer gas. The development work involves a new, more flexible cocurrent gasifier and a cleaning step for the counter-current producer gas. (orig.)

  14. Microvessel density in the placental bed among preeclampsia patients

    Directory of Open Access Journals (Sweden)

    Tarcisio Mota Coelho

    Full Text Available CONTEXT AND OBJECTIVE: Morphological changes in the spiral arteries of the placental bed have been studied in patients with preeclampsia, one of the largest causes of maternal and perinatal morbidity and mortality. The reports show that vasospasm and vascular endothelial injury were two major pathological conditions for preeclampsia. The aim of this study was to investigate the microvessel density of spiral arteries in the placental bed, in pregnancies complicated by hypertension and proteinuria, and in normal pregnancies. DESIGN AND SETTING: This was a cross-sectional survey of immunohistochemical studies on biopsies from the spiral arteries of the placental bed, among women undergoing cesarean sections for clinical and obstetrical reasons at Universidade Federal de São Paulo, São Paulo, Brazil. METHODS: Placental bed biopsies were obtained during cesarean section after placenta removal, with direct viewing of the central area of placenta insertion. The microvessel density of spiral arteries was measured by immunohistochemical methods in decidual and myometrial segments, using CD34 antibody. RESULTS: Biopsies containing spiral arteries were obtained from 34 hypertensive pregnant women with proteinuria, and 26 normotensive pregnant women. The microvessel densities in decidual and myometrial segments of the placental bed were compared between the groups. It was observed that, with increasing blood pressure and proteinuria, the microvessel density gradually decreased. CONCLUSION: The presence of high levels of hypertension and proteinuria may be associated with a progressive decrease in microvessel density in the placental bed.

  15. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball

    Overview From a technical perspective, CMS has been in “beam operation” state since 6th November. The detector is fully closed with all components operational and the magnetic field is normally at the nominal 3.8T. The UXC cavern is normally closed with the radiation veto set. Access to UXC is now only possible during downtimes of LHC. Such accesses must be carefully planned, documented and carried out in agreement with CMS Technical Coordination, Experimental Area Management, LHC programme coordination and the CCC. Material flow in and out of UXC is now strictly controlled. Access to USC remains possible at any time, although, for safety reasons, it is necessary to register with the shift crew in the control room before going down.It is obligatory for all material leaving UXC to pass through the underground buffer zone for RP scanning, database entry and appropriate labeling for traceability. Technical coordination (notably Stephane Bally and Christoph Schaefer), the shift crew and run ...

  16. The Pebble Bed Modular Reactor: An obituary

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Steve, E-mail: stephen.thomas@gre.ac.u [Public Services International Research Unit (PSIRU), Business School, University of Greenwich, 30 Park Row, London SE10 9LS (United Kingdom)

    2011-05-15

    The High Temperature Gas-cooled Reactor (HTGR) has exerted a peculiar attraction over nuclear engineers. Despite many unsuccessful attempts over half a century to develop it as a commercial power reactor, there is still a strong belief amongst many nuclear advocates that a highly successful HTGR technology will emerge. The most recent attempt to commercialize an HTGR design, the Pebble Bed Modular Reactor (PBMR), was abandoned in 2010 after 12 years of effort and the expenditure of a large amount of South African public money. This article reviews this latest attempt to commercialize an HTGR design and attempts to identify which issues have led to its failure and what lessons can be learnt from this experience. It concludes that any further attempts to develop HTGRs using Pebble Bed technology should only be undertaken if there is a clear understanding of why earlier attempts have failed and a high level of confidence that earlier problems have been overcome. It argues that the PBMR project has exposed serious weaknesses in accountability mechanisms for the expenditure of South African public money. - Research highlights: {yields} In this study we examine the reasons behind the failure of the South African PBMR programme. {yields} The study reviews the technical issues that have arisen and lessons for future reactor developments. {yields} The study also identifies weaknesses in the accountability mechanisms for public spending.

  17. Design requirements for the supercritical water oxidation test bed

    Energy Technology Data Exchange (ETDEWEB)

    Svoboda, J.M.; Valentich, D.J.

    1994-05-01

    This report describes the design requirements for the supercritical water oxidation (SCWO) test bed that will be located at the Idaho National Engineering Laboratory (INEL). The test bed will process a maximum of 50 gph of waste plus the required volume of cooling water. The test bed will evaluate the performance of a number of SCWO reactor designs. The goal of the project is to select a reactor that can be scaled up for use in a full-size waste treatment facility to process US Department of Energy mixed wastes. EG&G Idaho, Inc. will design and construct the SCWO test bed at the Water Reactor Research Test Facility (WRRTF), located in the northern region of the INEL. Private industry partners will develop and provide SCWO reactors to interface with the test bed. A number of reactor designs will be tested, including a transpiring wall, tube, and vessel-type reactor. The initial SCWO reactor evaluated will be a transpiring wall design. This design requirements report identifies parameters needed to proceed with preliminary and final design work for the SCWO test bed. A flow sheet and Process and Instrumentation Diagrams define the overall process and conditions of service and delineate equipment, piping, and instrumentation sizes and configuration Codes and standards that govern the safe engineering and design of systems and guidance that locates and interfaces test bed hardware are provided. Detailed technical requirements are addressed for design of piping, valves, instrumentation and control, vessels, tanks, pumps, electrical systems, and structural steel. The approach for conducting the preliminary and final designs and environmental and quality issues influencing the design are provided.

  18. Dynamics of fine particles in liquid-solid fluidized beds

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    On the basis of the Local Equilibrium Model (LEM), fine particles with large Richardson-Zaki exponent n show, under certain conditions during bed expansion and collapse, different dynamic behavior from particles with small n. For an expansion process there may be a concentration discontinuity propagating upward from the distributor, and, on the contrary, for a collapse process there may be a progressively broadening and upward-propagating continuous transition zone instead of discontinuity. The predictions of the bed height variation and the discontinuity trace have been validated experimentally.

  19. A technological evaluation of the Microsoft Kinect for automated behavioural mapping at bed rest.

    Science.gov (United States)

    Gibson, Simon; McBride, Simon J; McClelland, Coen; Watson, Marcus

    2013-01-01

    Behavioural mapping (BM) is a long established method of structured observational study used to understand where patients are and what they are doing within a hospital setting. BM is prominent in stroke rehabilitation research, where that research indicates patients spend most of their time at bed rest. We evaluate the technical feasibility of using the Microsoft Kinect to automate patient physical activity classification at bed rest.

  20. Torsion testing of bed joints

    DEFF Research Database (Denmark)

    Hansen, Klavs Feilberg; Pedersen, Carsten Mørk

    2008-01-01

    be carried out directly in a normal testing machine. The torsion strength is believed to be the most important parameter in out-of-plane resistance of masonry walls subjected to bending about an axis perpendicular to the bed joints. The paper also contains a few test results from bending of small walls about...... an axis perpendicular to the bed joints, which indicate the close connection between these results and results from torsion tests. These characteristics make the torsion strength well suited to act as substitute parameter for the bending strength of masonry about an axis perpendicular to the bed joints....